WorldWideScience

Sample records for relative fuel economy

  1. 40 CFR 600.208-12 - Calculation of FTP-based and HFET-based fuel economy and carbon-related exhaust emission values...

    Science.gov (United States)

    2010-07-01

    ...-based fuel economy and carbon-related exhaust emission values for a model type. 600.208-12 Section 600... ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later...-based and HFET-based fuel economy and carbon-related exhaust emission values for a model type. (a) Fuel...

  2. www.FuelEconomy.gov

    Data.gov (United States)

    U.S. Environmental Protection Agency — FuelEconomy.gov provides comprehensive information about vehicles' fuel economy. The official U.S. government site for fuel economy information, it is operated by...

  3. 49 CFR 537.9 - Determination of fuel economy values and average fuel economy.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 6 2010-10-01 2010-10-01 false Determination of fuel economy values and average fuel economy. 537.9 Section 537.9 Transportation Other Regulations Relating to Transportation (Continued) NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AUTOMOTIVE FUEL ECONOMY REPORTS § 537.9 Determination of fuel...

  4. Fuel economy handbook

    Energy Technology Data Exchange (ETDEWEB)

    Short, W [ed.

    1979-01-01

    An overview of the UK's energy situation from 1950 to 2020 is presented. Problems are discussed and recommendations are made. A strong argument is presented for energy conservation, greater use of nuclear energy, and restrained production of North Sea oil. Specific recommendations are made for financial and operational considerations of (1) new or replacement boiler plants; (2) space heating of factories, offices and similar buildings; and (3) possible use of various fuels including duel-fuel economics and use of wastes. Tariffs and charges are discussed as well as services (e.g. compressed air, cooling water, sources of waste, etc.). Standby considerations (peak load lopping, turbines-engines, parallel or sectioned operation, etc.) and heat distribution (steam, condensate return and uses) are discussed. Throughout, the emphasis is on fuel economy. Savings in process such as recovering waste heat and the storage of heat are considered. For small industrial furnaces, intermittent heating, heat recovery, and the importance of furnace loading are discussed. (MJJ)

  5. 40 CFR 600.113-78 - Fuel economy calculations.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Fuel economy calculations. 600.113-78... FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1978 and Later Model Year Automobiles-Test Procedures § 600.113-78 Fuel economy calculations. The...

  6. 40 CFR 600.113-88 - Fuel economy calculations.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Fuel economy calculations. 600.113-88... FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1978 and Later Model Year Automobiles-Test Procedures § 600.113-88 Fuel economy calculations. The...

  7. 40 CFR 600.113-93 - Fuel economy calculations.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Fuel economy calculations. 600.113-93... FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1978 and Later Model Year Automobiles-Test Procedures § 600.113-93 Fuel economy calculations. The...

  8. 40 CFR 600.510-12 - Calculation of average fuel economy and average carbon-related exhaust emissions.

    Science.gov (United States)

    2010-07-01

    ... and average carbon-related exhaust emissions. 600.510-12 Section 600.510-12 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF... Transportation. (iv) [Reserved] (2) Average carbon-related exhaust emissions will be calculated to the nearest...

  9. Fuel Economy Testing and Data

    Science.gov (United States)

    EPA’s Fuel Economy pages provide information on current standards and how federal agencies work to enforce those laws, testing for national Corporate Average Fuel Economy or CAFE standards, and what you can do to reduce your own vehicle emissions.

  10. Fuel Economy Label and CAFE Data

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Engine and Vehicle Compliance Certification and Fuel Economy Inventory contains measured emissions and fuel economy compliance information for light duty...

  11. 40 CFR 600.206-12 - Calculation and use of FTP-based and HFET-based fuel economy and carbon-related exhaust emission...

    Science.gov (United States)

    2010-07-01

    ... POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for... vehicle under § 600.113(a) and (b) and as approved in § 600.008-08(c), are used to determine FTP-based... value exists for an electric vehicle configuration, that value, rounded to the nearest tenth of a mile...

  12. Model Year 2017 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2016-11-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

  13. Model Year 2012 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2011-11-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

  14. Model Year 2013 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2012-12-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

  15. Model Year 2011 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2010-11-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

  16. Model Year 2018 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2017-12-07

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles.

  17. METHODS TO MEASURE, PREDICT AND RELATE FRICTION, WEAR AND FUEL ECONOMY

    Energy Technology Data Exchange (ETDEWEB)

    Gravante, Steve [Ricardo, Inc.; Fenske, George [Argonne National Lab. (ANL), Argonne, IL (United States); Demas, Nicholas [Argonne National Lab. (ANL), Argonne, IL (United States); Erck, Robert [Argonne National Lab. (ANL), Argonne, IL (United States)

    2018-03-19

    High-fidelity measurements of the coefficient of friction and the parasitic friction power of the power cylinder components have been made for the Isuzu 5.2L 4H on-highway engine. In particular, measurements of the asperity friction coefficient were made with test coupons using Argonne National Lab’s (ANL) reciprocating test rig for the ring-on-liner and skirt-on-liner component pairs. These measurements correlated well with independent measurements made by Electro-Mechanical Associates (EMA). In addition, surface roughness measurements of the Isuzu components were made using white light interferometer (WLI). The asperity friction and surface characterization are key inputs to advanced CAE simulation tools such as RINGPAK and PISDYN which are used to predict the friction power and wear rates of power cylinder components. Finally, motored friction tests were successfully performed to quantify the friction mean effective pressure (FMEP) of the power cylinder components for various oils (High viscosity 15W40, low viscosity 5W20 with friction modifier (FM) and specially blended oil containing consisting of PAO/ZDDP/MoDTC) at 25, 50, and 110 °C. Ricardo's objective is to use this data along with advanced CAE methods to develop empirical characterizations of friction and wear mechanisms in internal combustion engines such that the impact of such mechanisms of engine fuel consumption and/or vehicle fuel economy can be estimated. The value of such predictive schemes is that if one knows how a particular friction reduction technology changes oil viscosity and/or the friction coefficient then the fuel consumption or fuel economy impacts can be estimated without the excessive cost of motored or fired engine tests by utilizing cost effective lab scale tests and in combination with advanced analytical methods. One accomplishment made during this work was the development and validation of a novel technique for quantifying wear using data from WLI through the use of

  18. 40 CFR 600.114-08 - Vehicle-specific 5-cycle fuel economy calculations.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Vehicle-specific 5-cycle fuel economy... (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy... fuel economy calculations. This section applies to data used for fuel economy labeling under Subpart D...

  19. Model Year 2015 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2014-12-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

  20. Model Year 2009 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2008-10-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

  1. Model Year 2005 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2004-11-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

  2. Model Year 2016 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2015-11-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

  3. Model Year 2010 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2009-10-14

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

  4. Model Year 2014 Fuel Economy Guide: EPA Fuel Economy Estimates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2013-12-01

    The Fuel Economy Guide is published by the U.S. Department of Energy as an aid to consumers considering the purchase of a new vehicle. The Guide lists estimates of miles per gallon (mpg) for each vehicle available for the new model year. These estimates are provided by the U.S. Environmental Protection Agency in compliance with Federal Law. By using this Guide, consumers can estimate the average yearly fuel cost for any vehicle. The Guide is intended to help consumers compare the fuel economy of similarly sized cars, light duty trucks and special purpose vehicles. The vehicles listed have been divided into three classes of cars, three classes of light duty trucks, and three classes of special purpose vehicles.

  5. Substantial Improvements of Fuel Economy

    DEFF Research Database (Denmark)

    Jørgensen, Kaj; Nielsen, Lars H.

    1996-01-01

    The paper evaluates the scope for improving the energy and environmental impacts of road transport by means of electrical and hybrid propulsion. These technologies promise considerable improvements of the fuel economy compared to equivalent vehicles mas well as beneficial effects for the energy...... and traffic systems. A case study concerning passenger cars is analysed by means of computer simulation....

  6. Car buyers and fuel economy?

    International Nuclear Information System (INIS)

    Turrentine, Thomas S.; Kurani, Kenneth S.

    2007-01-01

    This research is designed to help researchers and policy makers ground their work in the reality of how US consumers are thinking and behaving with respect to automotive fuel economy. Our data are from semi-structured interviews with 57 households across nine lifestyle 'sectors.' We found no household that analyzed their fuel costs in a systematic way in their automobile or gasoline purchases. Almost none of these households track gasoline costs over time or consider them explicitly in household budgets. These households may know the cost of their last tank of gasoline and the unit price of gasoline on that day, but this accurate information is rapidly forgotten and replaced by typical information. One effect of this lack of knowledge and information is that when consumers buy a vehicle, they do not have the basic building blocks of knowledge assumed by the model of economically rational decision-making, and they make large errors estimating gasoline costs and savings over time. Moreover, we find that consumer value for fuel economy is not only about private cost savings. Fuel economy can be a symbolic value as well, for example among drivers who view resource conservation or thrift as important values to communicate. Consumers also assign non-monetary meaning to fuel prices, for example seeing rising prices as evidence of conspiracy. This research suggests that consumer responses to fuel economy technology and changes in fuel prices are more complex than economic assumptions suggest. The US Department of Energy and the Energy Foundation supported this research. The authors are solely responsible for the content and conclusions presented

  7. Fuel Economy Label and CAFE Data

    Science.gov (United States)

    The Engine and Vehicle Compliance Certification and Fuel Economy Inventory contains measured emissions and fuel economy compliance information for light duty vehicles. Data is collected by EPA to certify compliance with the applicable fuel economy provisions of the Energy Policy and Conservation Act (EPCA) and The Energy Independent Security Act of 2007

  8. 40 CFR 600.211-08 - Sample calculation of fuel economy values for labeling.

    Science.gov (United States)

    2010-07-01

    ... AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-Procedures for Calculating Fuel Economy... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Sample calculation of fuel economy...

  9. 40 CFR 600.209-85 - Calculation of fuel economy values for labeling.

    Science.gov (United States)

    2010-07-01

    ... (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-Procedures for Calculating Fuel Economy Values § 600.209... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Calculation of fuel economy values for...

  10. 40 CFR 600.209-95 - Calculation of fuel economy values for labeling.

    Science.gov (United States)

    2010-07-01

    ... (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-Procedures for Calculating Fuel Economy Values § 600.209... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Calculation of fuel economy values for...

  11. 40 CFR Appendix II to Part 600 - Sample Fuel Economy Calculations

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Sample Fuel Economy Calculations II... FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Pt. 600, App. II Appendix II to Part 600—Sample Fuel Economy Calculations (a) This sample fuel economy calculation is applicable to...

  12. Economy and the fuel market

    International Nuclear Information System (INIS)

    1994-01-01

    The nuclear fuel manufacturing constitutes a considerable venture for the competitiveness of the nuclear power sector although it represents a relatively modest fraction (around 4%) of the nuclear kWh cost. The COGEMA group is participating through its branches in the control of the most part (32%) of the world manufacturing capacity of fuel for PWR. Amounting up to 242 operating installations this reactor type is the most widespread in the world. The paper discusses the costs, the fuel clients and the fuel suppliers. Data concerning the boiling water and fast neutron reactors, geographical localization of the PWR and VVER reactors all over the world, the PWR and fuel for PWR manufacturers are also presented

  13. Sipping fuel and saving lives: increasing fuel economy withoutsacrificing safety

    Energy Technology Data Exchange (ETDEWEB)

    Gordon, Deborah; Greene, David L.; Ross, Marc H.; Wenzel, Tom P.

    2007-06-11

    The public, automakers, and policymakers have long worried about trade-offs between increased fuel economy in motor vehicles and reduced safety. The conclusion of a broad group of experts on safety and fuel economy in the auto sector is that no trade-off is required. There are a wide variety of technologies and approaches available to advance vehicle fuel economy that have no effect on vehicle safety. Conversely, there are many technologies and approaches available to advance vehicle safety that are not detrimental to vehicle fuel economy. Congress is considering new policies to increase the fuel economy of new automobiles in order to reduce oil dependence and reduce greenhouse gas emissions. The findings reported here offer reassurance on an important dimension of that work: It is possible to significantly increase the fuel economy of motor vehicles without compromising their safety. Automobiles on the road today demonstrate that higher fuel economy and greater safety can co-exist. Some of the safest vehicles have higher fuel economy, while some of the least safe vehicles driven today--heavy, large trucks and SUVs--have the lowest fuel economy. At an October 3, 2006 workshop, leading researchers from national laboratories, academia, auto manufacturers, insurance research industry, consumer and environmental groups, material supply industries, and the federal government agreed that vehicles could be designed to simultaneously improve safety and fuel economy. The real question is not whether we can realize this goal, but the best path to get there. The experts' studies reveal important new conclusions about fuel economy and safety, including: (1) Vehicle fuel economy can be increased without affecting safety, and vice versa; (2) Reducing the weight and height of the heaviest SUVs and pickup trucks will simultaneously increase both their fuel economy and overall safety; and (3) Advanced materials can decouple size from mass, creating important new possibilities

  14. Fuel Economy Label and CAFE Data Inventory

    Science.gov (United States)

    The Fuel Economy Label and CAFE Data asset contains measured summary fuel economy estimates and test data for light-duty vehicle manufacturers by model for certification as required under the Energy Policy and Conservation Act of 1975 (EPCA) and The Energy Independent Security Act of 2007 (EISA) to collect vehicle fuel economy estimates for the creation of Economy Labels and for the calculation of Corporate Average Fuel Economy (CAFE). Manufacturers submit data on an annual basis, or as needed to document vehicle model changes.The EPA performs targeted fuel economy confirmatory tests on approximately 15% of vehicles submitted for validation. Confirmatory data on vehicles is associated with its corresponding submission data to verify the accuracy of manufacturer submissions beyond standard business rules. Submitted data comes in XML format or as documents, with the majority of submissions being sent in XML, and includes descriptive information on the vehicle itself, fuel economy information, and the manufacturer's testing approach. This data may contain proprietary information (CBI) such as information on estimated sales or other data elements indicated by the submitter as confidential. CBI data is not publically available; however, within the EPA data can accessed under the restrictions of the Office of Transportation and Air Quality (OTAQ) CBI policy [RCS Link]. Datasets are segmented by vehicle model/manufacturer and/or year with corresponding fuel economy, te

  15. Comparing flexibility mechanisms for fuel economy standards

    International Nuclear Information System (INIS)

    Fischer, Carolyn

    2008-01-01

    Since 1975, the Corporate Average Fuel Economy (CAFE) program has been the main policy tool in the US for coping with the problems of increasing fuel consumption and dependence on imported oil. The program mandates average fuel economy requirements for the new vehicle sales of each manufacturer's fleet, with separate standards for cars and light trucks. The fact that each manufacturer must on its own meet the standards means that the incentives to improve fuel economy are different across manufacturers and vehicle types, although the problems associated with fuel consumption do not make such distinctions. This paper evaluates different mechanisms to offer automakers the flexibility of joint compliance with nationwide fuel economy goals: tradable CAFE credits, feebates, output-rebated fees, and tradable credits with banking. The policies are compared according to the short- and long-run economic incentives, as well as to issues of transparency, implementation, administrative and transaction costs, and uncertainty

  16. 40 CFR 600.307-08 - Fuel economy label format requirements.

    Science.gov (United States)

    2010-07-01

    ... to battery electric vehicles, fuel cell vehicles, plug-in hybrid electric vehicles and vehicles... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Fuel economy label format requirements...) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy...

  17. 40 CFR 600.210-08 - Calculation of fuel economy values for labeling.

    Science.gov (United States)

    2010-07-01

    ... including, but not limited to battery electric vehicles, fuel cell vehicles, plug-in hybrid electric... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Calculation of fuel economy values for... (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy...

  18. 40 CFR 600.006-08 - Data and information requirements for fuel economy vehicles.

    Science.gov (United States)

    2010-07-01

    ... controller, battery configuration, or other components performed within 2,000 miles prior to fuel economy... fuel economy vehicles. 600.006-08 Section 600.006-08 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel...

  19. Green economy and related concepts

    NARCIS (Netherlands)

    Loiseau, Eleonore; Saikku, Laura; Antikainen, Riina; Droste, Nils; Hansjürgens, Bernd; Pitkänen, Kati; Leskinen, Pekka; Kuikman, Peter; Thomsen, Marianne

    2016-01-01

    For the last ten years, the notion of a green economy has become increasingly attractive to policy makers. However, green economy covers a lot of diverse concepts and its links with sustainability are not always clear. In this article, we focus on definitions of green economy and related concepts

  20. Technology Roadmap: Fuel Economy of Road Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-07-01

    This roadmap explores the potential improvement of existing technologies to enhance the average fuel economy of motorised vehicles; the roadmap’s vision is to achieve a 30% to 50% reduction in fuel use per kilometre from new road vehicles including 2-wheelers, LDV s and HDV s) around the world in 2030, and from the stock of all vehicles on the road by 2050. This achievement would contribute to significant reductions in GHG emissions and oil use, compared to a baseline projection. Different motorised modes are treated separately, with a focus on LDV s, HDV s and powered two-wheelers. A section on in-use fuel economy also addresses technical and nontechnical parameters that could allow fuel economy to drastically improve over the next decades. Technology cost analysis and payback time show that significant progress can be made with low or negative cost for fuel-efficient vehicles over their lifetime use. Even though the latest data analysed by the IEA for fuel economy between 2005 and 2008 showed that a gap exists in achieving the roadmap’s vision, cutting the average fuel economy of road motorised vehicles by 30% to 50% by 2030 is achievable, and the policies and technologies that could help meet this challenge are already deployed in many places around the world.

  1. Effect of Intake Air Filter Condition on Vehicle Fuel Economy

    Energy Technology Data Exchange (ETDEWEB)

    Norman, Kevin M [ORNL; Huff, Shean P [ORNL; West, Brian H [ORNL

    2009-02-01

    The U.S. Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy and the U.S. Environmental Protection Agency (EPA) jointly maintain a fuel economy website (www.fueleconomy.gov), which helps fulfill their responsibility under the Energy Policy Act of 1992 to provide accurate fuel economy information [in miles per gallon (mpg)] to consumers. The site provides information on EPA fuel economy ratings for passenger cars and light trucks from 1985 to the present and other relevant information related to energy use such as alternative fuels and driving and vehicle maintenance tips. In recent years, fluctuations in the price of crude oil and corresponding fluctuations in the price of gasoline and diesel fuels have renewed interest in vehicle fuel economy in the United States. (User sessions on the fuel economy website exceeded 20 million in 2008 compared to less than 5 million in 2004 and less than 1 million in 2001.) As a result of this renewed interest and the age of some of the references cited in the tips section of the website, DOE authorized the Oak Ridge National Laboratory (ORNL) Fuels, Engines, and Emissions Research Center (FEERC) to initiate studies to validate and improve these tips. This report documents a study aimed specifically at the effect of engine air filter condition on fuel economy. The goal of this study was to explore the effects of a clogged air filter on the fuel economy of vehicles operating over prescribed test cycles. Three newer vehicles (a 2007 Buick Lucerne, a 2006 Dodge Charger, and a 2003 Toyota Camry) and an older carbureted vehicle were tested. Results show that clogging the air filter has no significant effect on the fuel economy of the newer vehicles (all fuel injected with closed-loop control and one equipped with MDS). The engine control systems were able to maintain the desired AFR regardless of intake restrictions, and therefore fuel consumption was not increased. The carbureted engine did show a decrease in

  2. Consumer Views: Importance of Fuel Economy

    Energy Technology Data Exchange (ETDEWEB)

    Singer, Mark [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2017-04-11

    This presentation includes data captured by the National Renewable Energy Laboratory (NREL) to support the U.S. Department of Energy's Vehicle Technologies Office (VTO) research efforts. The data capture consumer views on the importance of fuel economy amongst other vehicle attributes and views on which alternative fuel types would be the best and worst replacements for gasoline.

  3. Haptic seat for fuel economy feedback

    Energy Technology Data Exchange (ETDEWEB)

    Bobbitt, III, John Thomas

    2016-08-30

    A process of providing driver fuel economy feedback is disclosed in which vehicle sensors provide for haptic feedback on fuel usage. Such sensors may include one or more of a speed sensors, global position satellite units, vehicle pitch/roll angle sensors, suspension displacement sensors, longitudinal accelerometer sensors, throttle position in sensors, steering angle sensors, break pressure sensors, and lateral accelerometer sensors. Sensors used singlely or collectively can provide enhanced feedback as to various environmental conditions and operating conditions such that a more accurate assessment of fuel economy information can be provided to the driver.

  4. 40 CFR Appendix III to Part 600 - Sample Fuel Economy Label Calculation

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Sample Fuel Economy Label Calculation...) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Pt. 600, App. III Appendix III to Part 600—Sample Fuel Economy Label Calculation Suppose that a manufacturer called Mizer...

  5. 40 CFR 600.510-08 - Calculation of average fuel economy.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Calculation of average fuel economy. 600.510-08 Section 600.510-08 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for Model Year 1978 Passenger Automobiles...

  6. 40 CFR 600.510-93 - Calculation of average fuel economy.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Calculation of average fuel economy. 600.510-93 Section 600.510-93 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for Model Year 1978 Passenger Automobiles...

  7. 40 CFR 600.510-86 - Calculation of average fuel economy.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Calculation of average fuel economy. 600.510-86 Section 600.510-86 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for Model Year 1978 Passenger Automobiles...

  8. 40 CFR 600.006-86 - Data and information requirements for fuel economy vehicles.

    Science.gov (United States)

    2010-07-01

    ... fuel economy vehicles. 600.006-86 Section 600.006-86 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-General Provisions § 600.006-86 Data and...

  9. 49 CFR 525.11 - Termination of exemption; amendment of alternative average fuel economy standard.

    Science.gov (United States)

    2010-10-01

    ... average fuel economy standard. 525.11 Section 525.11 Transportation Other Regulations Relating to... EXEMPTIONS FROM AVERAGE FUEL ECONOMY STANDARDS § 525.11 Termination of exemption; amendment of alternative average fuel economy standard. (a) Any exemption granted under this part for an affected model year does...

  10. 40 CFR 600.006-89 - Data and information requirements for fuel economy vehicles.

    Science.gov (United States)

    2010-07-01

    ... fuel economy vehicles. 600.006-89 Section 600.006-89 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-General Provisions § 600.006-89 Data and...

  11. The System Dynamics of U.S. Automobile Fuel Economy

    Directory of Open Access Journals (Sweden)

    Todd K. BenDor

    2012-05-01

    Full Text Available This paper analyzes the dynamics of U.S. automobile gasoline consumption since 1975. Using background literature on the history of domestic fuel economy and energy policy, I establish a conceptual model that explains historical trends in adoption of increased fuel economy. I then create a system dynamics simulation model to understand the relationship between increased fuel economy standards and potential changes to gas tax policies. The model suggests that when increases in mandated fuel economy are not conducted in an environment with rising fuel costs, fuel economy improvements may be directly counteracted by shifting tastes of consumers towards larger automobiles with lower fuel economy.

  12. Nuclear fuel burn-up economy

    International Nuclear Information System (INIS)

    Matausek, M.

    1984-01-01

    In the period 1981-1985, for the needs of Utility Organization, Beograd, and with the support of the Scientific Council of SR Srbija, work has been performed on the study entitled 'Nuclear Fuel Burn-up Economy'. The forst [phase, completed during the year 1983 comprised: comparative analysis of commercial NPP from the standpoint of nuclear fuel requirements; development of methods for fuel burn-up analysis; specification of elements concerning the nuclear fuel for the tender documentation. The present paper gives the short description of the purpose, content and results achieved in the up-to-now work on the study. (author)

  13. Fuel demand on UK roads and dieselisation of fuel economy

    International Nuclear Information System (INIS)

    Bonilla, David

    2009-01-01

    Because of high oil prices, and climate change policy, governments are now seeking ways to improve new car fuel economy thus contributing to air quality and energy security. One strategy is to increase dieselisation rates of the vehicle fleet. Recent trends in fuel economy show improvement since 1995, however, efforts need to go further if the EU Voluntary Agreement targets on CO 2 (a greenhouse gas emission standard) are to be achieved. Trends show diesel car sales have accelerated rapidly and that the advantage of new car fuel economy of diesel cars over gasoline ones is narrowing posing a new challenge. We estimate the demand for new car fuel economy in the UK. In the long-run consumers buy fuel economy, but not in the short-run. We found that long-term income and price changes were the main drivers to achieve improvements particularly for diesel cars and that there is no break in the trend of fuel economy induced by the agreement adopted in the 1990s. Policy should target more closely both consumer choice of, and use of, diesel cars.

  14. 40 CFR 600.006-87 - Data and information requirements for fuel economy vehicles.

    Science.gov (United States)

    2010-07-01

    ..., motor controller, battery configuration, or other components performed within 2,000 miles prior to fuel... fuel economy vehicles. 600.006-87 Section 600.006-87 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel...

  15. Fuel economy of hybrid fuel-cell vehicles

    Science.gov (United States)

    Ahluwalia, Rajesh K.; Wang, X.; Rousseau, A.

    The potential improvement in fuel economy of a mid-size fuel-cell vehicle by combining it with an energy storage system has been assessed. An energy management strategy is developed and used to operate the direct hydrogen, pressurized fuel-cell system in a load-following mode and the energy storage system in a charge-sustaining mode. The strategy places highest priority on maintaining the energy storage system in a state where it can supply unanticipated boost power when the fuel-cell system alone cannot meet the power demand. It is found that downsizing a fuel-cell system decreases its efficiency on a drive cycle which is compensated by partial regenerative capture of braking energy. On a highway cycle with limited braking energy the increase in fuel economy with hybridization is small but on the stop-and-go urban cycle the fuel economy can improve by 27%. On the combined highway and urban drive cycles the fuel economy of the fuel-cell vehicle is estimated to increase by up to 15% by hybridizing it with an energy storage system.

  16. Motor vehicle fuel economy, the forgotten HC control stragegy?

    Energy Technology Data Exchange (ETDEWEB)

    Deluchi, M.; Wang, Quanlu; Greene, D.L.

    1992-06-01

    Emissions of hydrocarbons from motor vehicles are recognized as major contributors to ozone pollution in urban areas. Petroleum-based motor fuels contain volatile organic compounds (VOC) which, together with oxides of nitrogen, promote the formation of ozone in the troposphere via complex photochemical reactions. VOC emissions from the tailpipe and evaporation from the fuel and engine systems of highway vehicles are believed to account for about 40% of total VOC emissions in any region. But motor fuels also generate emissions throughout the fuel cycle, from crude oil production to refining, storage, transportation, and handling, that can make significant contributions to the total inventory of VOC emissions. Many of these sources of emissions are directly related to the quantity of fuel produced and handled throughout the fuel cycle. It is, therefore, reasonable to expect that a reduction in total fuel throughput might result in a reduction of VOC emissions. In particular, reducing vehicle fuel consumption by increasing vehicle fuel economy should reduce total fuel throughput, thereby cutting total emissions of VOCS. In this report we identify the sources of VOC emissions throughout the motor fuel cycle, quantify them to the extent possible, and describe their dependence on automobile and light truck fuel economy.

  17. Automobile Buyer Decisions about Fuel Economy and Fuel Efficiency

    OpenAIRE

    Kurani, Ken; Turrentine, Thomas

    2004-01-01

    Much prior research into consumer automotive and fuel purchase behaviors and fuel economy has been shaped by the normative assumptions of economics. Among these assumptions are that consumers should pay attention to costs of fuel and that they are aware of their options to save on fuel over long periods of time, i.e., the life of a vehicle or at least their period of ownership. For example, researchers have analyzed in some depth consumer choices for more fuel economical vehicles in the 1980s...

  18. 40 CFR 610.42 - Fuel economy measurement.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Fuel economy measurement. 610.42... ECONOMY RETROFIT DEVICES Test Procedures and Evaluation Criteria General Vehicle Test Procedures § 610.42 Fuel economy measurement. (a) Fuel consumption will be measured by: (1) The carbon balance method, or...

  19. 49 CFR 531.5 - Fuel economy standards.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 6 2010-10-01 2010-10-01 false Fuel economy standards. 531.5 Section 531.5... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION PASSENGER AUTOMOBILE AVERAGE FUEL ECONOMY STANDARDS § 531.5 Fuel economy standards. (a) Except as provided in paragraph (e) of this section, each manufacturer of passenger...

  20. Several remarks on the fuel cycle economy

    International Nuclear Information System (INIS)

    Roman Kubin; Rudolf Vespalec

    2007-01-01

    Present paper deals with some aspects influencing significantly cost of nuclear fuel and possibilities of its usage in optimal fuel cycle technology. Our discussion is focused on the phase of fuel procurement that means financial parts of the contract as well as its technical Appendices. Typically the fuel fabrication price is taken as the main economy indicator; nevertheless also many other financial and technical features of the contract must be taken into account in order to reach the best price of electricity sold into public energy grid. Our experience from several international tenders shows that the consistent complex of commercial and technical parameters of the contract is necessary to achieve optimal economic results and prepare proper conditions for advanced fuel cycle technology. Among those essential characteristics are payment conditions and schedule and extent of vendor's services and assistance to the operator. Very important role play also technical parameters, as safety and operational limits, influencing loading pattern quality and operating flexibility. Obviously also a level of operator's fuel cycle technology is a crucial point that is necessary for usage of technical quality of the fuel at the power plant. The final electricity price, produced by the plant, and uranium consumption are the only objective criteria to evaluate economic level of the fuel contract and the fuel cycle at all (Authors)

  1. LABOUR RELATIONS IN POSTINDUSTRIAL ECONOMY

    Directory of Open Access Journals (Sweden)

    Yuriy Rostislavovitch Chistyakov

    2013-09-01

    Full Text Available The article deals with inadequacy of present-day labour relations in economy. Out of date form of labour relations makes workforce dependable, causes social inequality, prevents economical development. The article gives results of theoretical and empiric research. The mechanism of guaranteed reproduction of labour to be realized as social partnership is offered.Purpose: the purpose is to give critical estimation of present-day labour relations in postindustrial economy.Method of studies: monographic, general theoretic economic analysis, correlation statistic analysisResults: a new modern adequate alternative form of labour relations guarantying the reproduction of labour is introducedField of application: industrial regulation both in economics in general and concrete businesses; motivation of workers.DOI: http://dx.doi.org/10.12731/2218-7405-2013-8-29

  2. 40 CFR Appendix Viii to Part 600 - Fuel Economy Label Formats

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Fuel Economy Label Formats VIII... POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Pt. 600, App. VIII Appendix VIII to Part 600—Fuel Economy Label Formats EC01MY92.117 EC01MY92.118 EC01MY92.119 EC01MY92.120...

  3. 40 CFR 600.209-08 - Calculation of vehicle-specific 5-cycle fuel economy values for a model type.

    Science.gov (United States)

    2010-07-01

    ...-cycle fuel economy values for a model type. 600.209-08 Section 600.209-08 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-Procedures for...

  4. Fuel economy and range estimates for fuel cell powered automobiles

    Energy Technology Data Exchange (ETDEWEB)

    Steinbugler, M.; Ogden, J. [Princeton Univ., NJ (United States)

    1996-12-31

    While a number of automotive fuel cell applications have been demonstrated, including a golf cart, buses, and a van, these systems and others that have been proposed have utilized differing configurations ranging from direct hydrogen fuel cell-only power plants to fuel cell/battery hybrids operating on reformed methanol. To date there is no clear consensus on which configuration, from among the possible combinations of fuel cell, peaking device, and fuel type, is the most likely to be successfully commercialized. System simplicity favors direct hydrogen fuel cell vehicles, but infrastructure is lacking. Infrastructure favors a system using a liquid fuel with a fuel processor, but system integration and performance issues remain. A number of studies have analyzed particular configurations on either a system or vehicle scale. The objective of this work is to estimate, within a consistent framework, fuel economies and ranges for a variety of configurations using flexible models with the goal of identifying the most promising configurations and the most important areas for further research and development.

  5. 40 CFR 600.314-08 - Updating label values, annual fuel cost, Gas Guzzler Tax, and range of fuel economy for...

    Science.gov (United States)

    2010-07-01

    ... cost, Gas Guzzler Tax, and range of fuel economy for comparable automobiles. 600.314-08 Section 600.314-08 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later...

  6. New vehicle fuel economy in the UK: Impact of the recession and recent policies

    International Nuclear Information System (INIS)

    Wadud, Zia

    2014-01-01

    Interests in vehicle fuel economy have increased in the past few years with the implementations of more stringent CAFE standard in USA and mandatory carbon emission standard in the EU. We seek to understand the effects of recent policies such as restructuring of Vehicle Excise Duties and EU standard on new vehicle fuel economy in the UK. In the past few years there have been substantial fluctuations in income and fuel prices, offering an interesting testing ground to understand their impact on the demand for fuel economy in vehicles. We use a monthly dataset to find that the emission standard is the largest driver for fuel economy improvements in recent years. Also, contrary to some recent findings in Europe and in UK, we find that income has an effect and that the recession had some role in improving the fuel economy. The effects of fuel prices were relatively small. Restructuring of the VED also improved new vehicle fuel economy in the UK, but the scrappage scheme had no significant effect. Results indicate that both supply and demand side policies are effective in improving fuel economy, although quantitatively the emission standard appears more effective due to its stringency. It is also important to consider the effects of income while devising demand side policies. - Highlights: • Econometric modelling and simulation of new vehicle fuel economy in UK. • EU carbon standard is the largest reason behind improving fuel economy. • Recession and associated reduction in income also had a role. • Fuel price has some impact on new car fuel economy, but small. • VED restructuring had an impact, but scrappage scheme's impact was insignificant

  7. Algal biodiesel economy and competition among bio-fuels.

    Science.gov (United States)

    Lee, D H

    2011-01-01

    This investigation examines the possible results of policy support in developed and developing economies for developing algal biodiesel through to 2040. This investigation adopts the Taiwan General Equilibrium Model-Energy for Bio-fuels (TAIGEM-EB) to predict competition among the development of algal biodiesel, bioethanol and conventional crop-based biodiesel. Analytical results show that algal biodiesel will not be the major energy source in 2040 without strong support in developed economies. In contrast, bioethanol enjoys a development advantage relative to both forms of biodiesel. Finally, algal biodiesel will almost completely replace conventional biodiesel. CO(2) reduction benefits the development of the bio-fuels industry. Copyright © 2010 Elsevier Ltd. All rights reserved.

  8. Fueling Wisconsin's economy with renewable energy

    International Nuclear Information System (INIS)

    Clemmer, S.

    1995-01-01

    A dynamic macroeconomic model of the Wisconsin economy is used to estimate the economic impacts of displacing a portion of future investment in fossil fuel power plants (coal and natural gas) with renewable energy resources (biomass, wind, solar and hydro). The results show that renewable energy investments produce over three times more jobs, income and economic activity than the same amount of electricity generated from coal and natural gas power plants. Between 1995 and 2020, a 75% increase in renewable energy use generates approximately 65,000 more job-years of employment, $1.6 billion in higher disposable income and a $3.1 billion increase in gross regional product than conventional power plant investments. This includes the effects of a 0.3% average annual increase in electricity prices from renewable energy investments

  9. 40 CFR 600.206-86 - Calculation and use of fuel economy values for gasoline-fueled, diesel, and electric vehicle...

    Science.gov (United States)

    2010-07-01

    ... values for gasoline-fueled, diesel, and electric vehicle configurations. 600.206-86 Section 600.206-86...-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year... values for gasoline-fueled, diesel, and electric vehicle configurations. (a) Fuel economy values...

  10. Instrumentation of cars for fuel economy. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Morris, J E

    1982-04-01

    The development of an electronic system to control the air-fuel ratio (A/F) and ignition timing of an internal combustion engine to optimize fuel economy is described. Dynamometer and drive cycle testing of the system was performed. The results showed that a significant improvement in fuel economy can be achieved by a control system of the type developed. It is clear, however, that considerably more work needs to be done. One area mentioned is the need for more systematic fuel economy testing against speed and load as control parameters are varied for optimization, and a more economic air bypass system must be developed. (LCL)

  11. Determinants of consumer interest in fuel economy: Lessons for strengthening the conservation argument

    International Nuclear Information System (INIS)

    Popp, Michael; Vickery, Gina; Dixon, Bruce; Van de Velde, Liesbeth; Van Huylenbroeck, Guido; Verbeke, Wim

    2009-01-01

    With an outlook for higher global energy prices and concomitant increase of agricultural resources for the pursuit of fuel, consumers are expected to seek more fuel-economic transportation alternatives. This paper examines factors that influence the importance consumers place on fuel economy, with attention given to differences between American and European consumers. In a survey conducted simultaneously in the United States (U.S.) and Belgium in the fall of 2006, respondents in both countries ranked fuel economy high among characteristics considered when purchasing a new vehicle. Overall, respondents in the U.S. placed greater emphasis on fuel economy as a new-vehicle characteristic. Respondents' budgetary concerns carried a large weight when purchasing a new vehicle as reflected in their consideration of a fuel's relative price (e.g. gasoline vs. diesel vs. biofuel) and associated car repair and maintenance costs. On the other hand, high-income Americans displayed a lack of concern over fuel economy. Concern over the environment also played a role since consumers who felt empowered to affect the environment with their purchasing decisions (buying low and clean emission technology and fuels) placed greater importance on fuel economy. No statistically significant effects on fuel economy rankings were found related to vehicle performance, socio-demographic parameters of age, gender or education. Importantly, the tradeoff between using agricultural inputs for energy rather than for food, feed and fiber had no impact on concerns over fuel economy. Finally, contrary to expectations, U.S. respondents who valued domestically produced renewable fuels did not tend to value fuel economy. (author)

  12. Development of fuel economy 5W-20 gasoline engine oil; Teinenpi 5W-20 gasoline engine yu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Akiyama, K; Ueda, F; Kurono, K; Kawai, H; Sugiyama, S [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    A 5W-20 gasoline engine oil which improves vehicle fuel efficiency by more than 1.5% relative to a conventional 5W-30 gasoline engine oil was newly developed. Its high fuel economy performance lasts 10,000 km. The viscosity was optimized to satisfy both fuel economy and antiwear performances. Thiadiazole was used to retain the initial fuel economy performance provided by MoDTC. 5 refs., 7 figs., 2 tabs.

  13. 76 FR 31467 - Guide Concerning Fuel Economy Advertising for New Automobiles

    Science.gov (United States)

    2011-06-01

    ... the Fuel Economy Guide \\1\\ in 1975 to prevent deceptive fuel economy advertising for new automobiles... Economy Guide. That rulemaking will increase the coverage of EPA's new fuel economy labels to include... issue to new vehicle advertisers in the FTC's Fuel Economy Guide. Therefore, the Commission has...

  14. On-Road Validation of a Simplified Model for Estimating Real-World Fuel Economy: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Wood, Eric; Gonder, Jeff; Jehlik, Forrest

    2017-01-01

    On-road fuel economy is known to vary significantly between individual trips in real-world driving conditions. This work introduces a methodology for rapidly simulating a specific vehicle's fuel economy over the wide range of real-world conditions experienced across the country. On-road test data collected using a highly instrumented vehicle is used to refine and validate this modeling approach. Model accuracy relative to on-road data collection is relevant to the estimation of 'off-cycle credits' that compensate for real-world fuel economy benefits that are not observed during certification testing on a chassis dynamometer.

  15. Vehicle technologies, fuel-economy policies, and fuel-consumption rates of Chinese vehicles

    International Nuclear Information System (INIS)

    Huo Hong; He Kebin; Wang, Michael; Yao Zhiliang

    2012-01-01

    One of the principal ways to reduce transport-related energy use is to reduce fuel-consumption rates of motor vehicles (usually measured in liters of fuel per 100 km). Since 2004, China has implemented policies to improve vehicle technologies and lower the fuel-consumption rates of individual vehicles. Policy evaluation requires accurate and adequate information on vehicle fuel-consumption rates. However, such information, especially for Chinese vehicles under real-world operating conditions, is rarely available from official sources in China. For each vehicle type we first review the vehicle technologies and fuel-economy policies currently in place in China and their impacts. We then derive real-world (or on-road) fuel-consumption rates on the basis of information collected from various sources. We estimate that the real-world fuel-consumption rates of vehicles in China sold in 2009 are 9 L/100 km for light-duty passenger vehicles, 11.4 L/100 km for light-duty trucks, 22 L/100 km for inter-city transport buses, 40 L/100 km for urban transit buses, and 24.9 L/100 km for heavy-duty trucks. These results aid in understanding the levels of fuel consumption of existing Chinese vehicle fleets and the effectiveness of policies in reducing on-road fuel consumption, which can help in designing and evaluating future vehicle energy-efficiency policies. - Highlights: ► Vehicle fuel-consumption rate (VFCR) data are rarely available in China. ► We review the fuel-economy policies currently in place in China and their impacts. ► We derive real-world VFCRs on the basis of information collected from various sources. ► Results aid in understanding the fuel consumption levels of Chinese vehicle fleets. ► Results help in designing and evaluating future vehicle energy-efficiency policies.

  16. Light-Duty Vehicle CO2 and Fuel Economy Trends

    Science.gov (United States)

    This report provides data on the fuel economy, carbon dioxide (CO2) emissions, and technology trends of new light-duty vehicles (cars, minivans, sport utility vehicles, and pickup trucks) for model years 1975 to present in the United States.

  17. Fuel economy and traffic fatalities: multivariate analysis of international data

    International Nuclear Information System (INIS)

    Noland, Robert B.

    2005-01-01

    In the US motor vehicle fuel economy standards were imposed in the late 1970s, in response to the oil crises of that decade. Since then, efforts to increase the standards have not occurred, one reason being the argument that smaller vehicles (which are generally more efficient) are considered less safe. Recent analyses (Energy J.( 2004)) suggests that variance in vehicle weights may be more important than the absolute weights of vehicles in making the highway network less safe. In Europe and other countries, which generally have smaller more efficient vehicle fleets, due to relatively high gasoline taxes, this debate has not occurred. In particular, countries such as Great Britain and Sweden have far safer road transport systems than the US but also have much more efficient vehicle fleets. This suggests that either vehicle weight and size are unimportant or if they have an effect it is small compared to other factors. This paper uses international data to build econometric models that examine whether average vehicle fuel economy has any association with road traffic fatalities, while controlling for other factors that are associated with fatalities. The effect on pedestrian fatalities is also analyzed. Cross-sectional time-series data on traffic fatalities from OECD countries is used and negative binomial regression models are developed using panel data to determine whether any associations are present. Results find that changes in vehicle efficiency are not associated with changes in traffic fatalities, suggesting either that size and weight changes over time have not had a strong effect or are not associated with fuel economy improvements

  18. Should a vehicle fuel economy standard be combined with an economy-wide greenhouse gas emissions constraint? Implications for energy and climate policy in the United States

    International Nuclear Information System (INIS)

    Karplus, Valerie J.; Paltsev, Sergey; Babiker, Mustafa; Reilly, John M.

    2013-01-01

    The United States has adopted fuel economy standards that require increases in the on-road efficiency of new passenger vehicles, with the goal of reducing petroleum use and (more recently) greenhouse gas (GHG) emissions. Understanding the cost and effectiveness of fuel economy standards, alone and in combination with economy-wide policies that constrain GHG emissions, is essential to inform coordinated design of future climate and energy policy. We use a computable general equilibrium model, the MIT Emissions Prediction and Policy Analysis (EPPA) model, to investigate the effect of combining a fuel economy standard with an economy-wide GHG emissions constraint in the United States. First, a fuel economy standard is shown to be at least six to fourteen times less cost effective than a price instrument (fuel tax) when targeting an identical reduction in cumulative gasoline use. Second, when combined with a cap-and-trade (CAT) policy, a binding fuel economy standard increases the cost of meeting the GHG emissions constraint by forcing expensive reductions in passenger vehicle gasoline use, displacing more cost-effective abatement opportunities. Third, the impact of adding a fuel economy standard to the CAT policy depends on the availability and cost of abatement opportunities in transport—if advanced biofuels provide a cost-competitive, low carbon alternative to gasoline, the fuel economy standard does not bind and the use of low carbon fuels in passenger vehicles makes a significantly larger contribution to GHG emissions abatement relative to the case when biofuels are not available. This analysis underscores the potentially large costs of a fuel economy standard relative to alternative policies aimed at reducing petroleum use and GHG emissions. It further emphasizes the need to consider sensitivity to vehicle technology and alternative fuel availability and costs as well as economy-wide responses when forecasting the energy, environmental, and economic outcomes of

  19. 40 CFR 85.1510 - Maintenance instructions, warranties, emission labeling and fuel economy requirements.

    Science.gov (United States)

    2010-07-01

    ..., emission labeling and fuel economy requirements. 85.1510 Section 85.1510 Protection of Environment..., warranties, emission labeling and fuel economy requirements. The provisions of this section are applicable to... for final admission. (d) Fuel economy labeling. (1) The certificate holder shall affix a fuel economy...

  20. 10 CFR 474.3 - Petroleum-equivalent fuel economy calculation.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 3 2010-01-01 2010-01-01 false Petroleum-equivalent fuel economy calculation. 474.3..., DEVELOPMENT, AND DEMONSTRATION PROGRAM; PETROLEUM-EQUIVALENT FUEL ECONOMY CALCULATION § 474.3 Petroleum-equivalent fuel economy calculation. (a) The petroleum-equivalent fuel economy for an electric vehicle is...

  1. 77 FR 29751 - Agency Information Collection Activity Under OMB Review: Automotive Fuel Economy Reports

    Science.gov (United States)

    2012-05-18

    ...-0059] Agency Information Collection Activity Under OMB Review: Automotive Fuel Economy Reports AGENCY... Transportation on whether a manufacturer will comply with an applicable average fuel economy standard for the... R. Katz, Fuel Economy Division, Office of International Policy, Fuel Economy and Consumer Programs...

  2. Reduction of CO/sub 2/ emissions through fuel economy standards for diesel cars in pakistan

    International Nuclear Information System (INIS)

    Memon, L.A.; Mehlia, T.M.I.; Hassan, M.H.

    2007-01-01

    In Pakistan, like many developing countries, the increasing prosperity and population growth are resulting in accelerated growth in vehicle population and vehicle kilometers traveled. This causes air pollution due to huge CO/sub 2/ emissions. Automobile fuel economy standards have proven to be one of the most effective tools to control oil demand thereby reducing the GHG (Green House Gas) emissions like CO/sub 2/, This study presents the investigation to apply fuel economy standards in Pakistan, in order to predict the potential reduction in CO/sub 2/ emissions and saving in fuel demand. The study is focused on only diesel cars and the data of diesel car owners for previous fifteen years is obtained from the related sources in Pakistan. A growth trend of diesel car owners was analyzed and the number of diesel car owners in future was predicted by applying database computer software. Calculations were made to study the effect of fuel economy standards in terms of saving in fuel demand and the reduction in CO/sub 2/ emissions. The results reveal the potential application of fuel economy standards and it was found that a cumulative amount of fuel 39266775 liters can be saved and CO/sub 2/ emissions can be reduced by 106021 tons at the end of 2011-2012, if fuel economy standards are implemented in 2008-2009. (author)

  3. Gasoline-fueled hybrid vs. conventional vehicle emissions and fuel economy.

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, J.; Bharathan, D.; He, J.; Plotkin, S.; Santini, D.; Vyas, A.

    1999-06-18

    This paper addresses the relative fuel economy and emissions behavior, both measured and modeled, of technically comparable, contemporary hybrid and conventional vehicles fueled by gasoline, in terms of different driving cycles. Criteria pollutants (hydrocarbons, carbon monoxide, and nitrogen oxides) are discussed, and the potential emissions benefits of designing hybrids for grid connection are briefly considered. In 1997, Toyota estimated that their grid-independent hybrid vehicle would obtain twice the fuel economy of a comparable conventional vehicle on the Japan 10/15 mode driving cycle. This initial result, as well as the fuel economy level (66 mpg), made its way into the U.S. press. Criteria emissions amounting to one-tenth of Japanese standards were cited, and some have interpreted these results to suggest that the grid-independent hybrid can reduce criteria emissions in the U.S. more sharply than can a conventional gasoline vehicle. This paper shows that the potential of contemporary grid-independent hybrid vehicle technology for reducing emissions and fuel consumption under U.S. driving conditions is less than some have inferred. The importance (and difficulty) of doing test and model assessments with comparable driving cycles, comparable emissions control technology, and comparable performance capabilities is emphasized. Compared with comparable-technology conventional vehicles, grid-independent hybrids appear to have no clear criteria pollutant benefits (or disbenefits). (Such benefits are clearly possible with grid-connectable hybrids operating in zero emissions mode.) However, significant reductions in greenhouse gas emissions (i.e., fuel consumption) are possible with hybrid vehicles when they are used to best advantage.

  4. The economy of the nuclear fuel cycle

    Energy Technology Data Exchange (ETDEWEB)

    Stoll, W [Alpha Chemie und Metallurgie G.m.b.H. (ALKEM), Hanau (Germany, F.R.)

    1989-07-01

    Heat extracted from nuclear fuel costs by a factor of 3 to 7 less than heat from conventional fossile fuel. So, nuclear fuel per se has an economical advantage, decreased however partly by higher nuclear plant investment costs. The standard LWR design does not allow all the fission energy stored in the fuel during on cycle to be used. It is therefore the most natural approach to separate fissionable species from fission products and consume them by fissioning. Whether this is economically justified as opposed by storing them indefinitely with spent fuel has widely been debated. The paper outlines the different approaches taken by nuclear communities worldwide and their perceived or proven rational arguments. It will balance economic and other factors for the near and distant future including advanced reactor concepts. The specific solution within the German nuclear programme will be explained, including foreseeable future trends. (orig.).

  5. Light-duty vehicle fuel economy improvements, 1979--1998: A consumer purchase model of corporate average fuel economy, fuel price, and income effects

    Science.gov (United States)

    Chien, David Michael

    2000-10-01

    The Energy Policy and Conservation Act of 1975, which created fuel economy standards for automobiles and light trucks, was passed by Congress in response to the rapid rise in world oil prices as a result of the 1973 oil crisis. The standards were first implemented in 1978 for automobiles and 1979 for light trucks, and began with initial standards of 18 MPG for automobiles and 17.2 MPG for light trucks. The current fuel economy standards for 1998 have been held constant at 27.5 MPG for automobiles and 20.5 MPG for light trucks since 1990--1991. While actual new automobile fuel economy has almost doubled from 14 MPG in 1974 to 27.2 MPG in 1994, it is reasonable to ask if the CAFE standards are still needed. Each year Congress attempts to pass another increase in the Corporate Average Fuel Economy (CAFE) standard and fails. Many have called for the abolition of CAFE standards citing the ineffectiveness of the standards in the past. In order to determine whether CAFE standards should be increased, held constant, or repealed, an evaluation of the effectiveness of the CAFE standards to date must be established. Because fuel prices were rising concurrently with the CAFE standards, many authors have attributed the rapid rise in new car fuel economy solely to fuel prices. The purpose of this dissertation is to re-examine the determinants of new car fuel economy via three effects: CAFE regulations, fuel price, and income effects. By measuring the marginal effects of the three fuel economy determinants upon consumers and manufacturers choices, for fuel economy, an estimate was made of the influence of each upon new fuel economy. The conclusions of this dissertation present some clear signals to policymakers: CAFE standards have been very effective in increasing fuel economy from 1979 to 1998. Furthermore, they have been the main cause of fuel economy improvement, with income being a much smaller component. Furthermore, this dissertation has suggested that fuel prices have

  6. Nuclear fuel burn-up economy; Ekonomija izgaranja nuklearnog goriva

    Energy Technology Data Exchange (ETDEWEB)

    Matausek, M [Institute of nuclear sciences Boris Kidric, Vinca, Beograd (Yugoslavia)

    1984-07-01

    In the period 1981-1985, for the needs of Utility Organization, Beograd, and with the support of the Scientific Council of SR Srbija, work has been performed on the study entitled 'Nuclear Fuel Burn-up Economy'. The forst [phase, completed during the year 1983 comprised: comparative analysis of commercial NPP from the standpoint of nuclear fuel requirements; development of methods for fuel burn-up analysis; specification of elements concerning the nuclear fuel for the tender documentation. The present paper gives the short description of the purpose, content and results achieved in the up-to-now work on the study. (author)

  7. Real-world fuel economy and CO2 emissions of plug-in hybrid electric vehicles

    International Nuclear Information System (INIS)

    Ploetz, Patrick; Funke, Simon Arpad; Jochem, Patrick

    2015-01-01

    Plug-in hybrid electric vehicles (PHEV) combine electric propulsion with an internal combustion engine. Their potential to reduce transport related green-house gas emissions highly depends on their actual usage and electricity provision. Various studies underline their environmental and economic advantages, but are based on standardised driving cycles, simulations or small PHEV fleets. Here, we analyse real-world fuel economy of PHEV and the factors influencing it based on about 2,000 actual PHEV that have been observed over more than a year in the U.S. and Germany. We find that real-world fuel economy of PHEV differ widely among users. The main factors explaining this variation are the annual mileage, the regularity of daily driving, and the likelihood of long-distance trips. Current test cycle fuel economy ratings neglect these factors. Despite the broad range of PHEV fuel economies, the test cycle fuel economy ratings can be close to empiric PHEV fleet averages if the average annual mile-age is about 17,000 km. For the largest group of PHEV in our data, the Chevrolet Volt, we find the average fuel economy to be 1.45 litres/100 km at an average electric driving share of 78%. The resulting real-world tank-to-wheel CO 2 emissions of these PHEV are 42 gCO 2 /km and the annual CO 2 savings in the U.S. amount to about 50 Mt. In conclusion, the variance of empirical PHEV fuel economy is considerably higher than of conventional vehicles. This should be taken into account by future test cycles and high electric driving shares should be incentivised.

  8. Benefits of recent improvements in vehicle fuel economy.

    Science.gov (United States)

    2014-10-01

    For the past several years, we have calculated (on a monthly basis) the average, sales-weighted fuel economy of all light-duty vehicles (cars, pickup trucks, vans, and SUVs) sold in : the U.S. The results indicate that, from October 2007 to September...

  9. Solid fuels. Coal. Economy and resources

    International Nuclear Information System (INIS)

    Bautin, F.; Martin-Amouroux, J.M.

    2007-01-01

    The share of coal in the world energy mix (25%) and its possible increase during the next decades is due to its specific use in steelmaking industry and to its excellent competitiveness in fossil-fuel power plants with respect to other energy sources. Its inferior energy efficiency is compensated by lower and more stable prices on international markets. This situation is explained by a strong competition and abundant reserves. However, coal is a strong emitter of greenhouse gases and would be temporarily penalized by the implementation of emission tax or trading systems before the development of carbon sequestration systems. This article presents: the main world markets (consumption per sector of activity, power generation market, coke market, start-up of a synthetic fuels market), the main international coal producers and traders (overview and typology, international trades, transport), the reserves and resources, and the worldwide perspectives (2050 scenarios, climatic risks, CO 2 prices and technological changes). (J.S.)

  10. Motor vehicle fuel economy, the forgotten HC control stragegy. [Hydrocarbon (HC)

    Energy Technology Data Exchange (ETDEWEB)

    Deluchi, M.; Wang, Quanlu; Greene, D.L.

    1992-06-01

    Emissions of hydrocarbons from motor vehicles are recognized as major contributors to ozone pollution in urban areas. Petroleum-based motor fuels contain volatile organic compounds (VOC) which, together with oxides of nitrogen, promote the formation of ozone in the troposphere via complex photochemical reactions. VOC emissions from the tailpipe and evaporation from the fuel and engine systems of highway vehicles are believed to account for about 40% of total VOC emissions in any region. But motor fuels also generate emissions throughout the fuel cycle, from crude oil production to refining, storage, transportation, and handling, that can make significant contributions to the total inventory of VOC emissions. Many of these sources of emissions are directly related to the quantity of fuel produced and handled throughout the fuel cycle. It is, therefore, reasonable to expect that a reduction in total fuel throughput might result in a reduction of VOC emissions. In particular, reducing vehicle fuel consumption by increasing vehicle fuel economy should reduce total fuel throughput, thereby cutting total emissions of VOCS. In this report we identify the sources of VOC emissions throughout the motor fuel cycle, quantify them to the extent possible, and describe their dependence on automobile and light truck fuel economy.

  11. Predicting Light-Duty Vehicle Fuel Economy as a Function of Highway Speed

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, John [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hwang, Ho-Ling [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); West, Brian [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Huff, Shean [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2013-04-08

    The www.fueleconomy.gov website offers information such as window label fuel economy for city, highway, and combined driving for all U.S.-legal light-duty vehicles from 1984 to the present. The site is jointly maintained by the U.S. Department of Energy and the U.S. Environmental Protection Agency (EPA), and also offers a considerable amount of consumer information and advice pertaining to vehicle fuel economy and energy related issues. Included with advice pertaining to driving styles and habits is information concerning the trend that as highway cruising speed is increased, fuel economy will degrade. An effort was undertaken to quantify this conventional wisdom through analysis of dynamometer testing results for 74 vehicles at steady state speeds from 50 to 80 mph. Using this experimental data, several simple models were developed to predict individual vehicle fuel economy and its rate of change over the 50-80 mph speed range interval. The models presented require a minimal number of vehicle attributes. The simplest model requires only the EPA window label highway mpg value (based on the EPA specified estimation method for 2008 and beyond). The most complex of these simple model uses vehicle coast-down test coefficients (from testing prescribed by SAE Standard J2263) known as the vehicle Target Coefficients, and the raw fuel economy result from the federal highway test. Statistical comparisons of these models and discussions of their expected usefulness and limitations are offered.

  12. 76 FR 54932 - Revisions and Additions to Motor Vehicle Fuel Economy Label; Correction

    Science.gov (United States)

    2011-09-06

    ...-AK73 Revisions and Additions to Motor Vehicle Fuel Economy Label; Correction AGENCY: Environmental... regarding labeling of cars and trucks with fuel economy and environmental information in the Federal...

  13. Automobile fuel; Economy and CO2 emissions in industrialized countries : troubling trends through 2005/6

    Science.gov (United States)

    2005-01-01

    A review of recently available data on both on-road fuel economy and new car test fuel economy : shows that while US on-road fuel economy has been flat for almost 15 years, major European countries and Japan have shown modest improvements in response...

  14. 10 CFR Appendix to Part 474 - Sample Petroleum-Equivalent Fuel Economy Calculations

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 3 2010-01-01 2010-01-01 false Sample Petroleum-Equivalent Fuel Economy Calculations..., DEVELOPMENT, AND DEMONSTRATION PROGRAM; PETROLEUM-EQUIVALENT FUEL ECONOMY CALCULATION Pt. 474, App. Appendix to Part 474—Sample Petroleum-Equivalent Fuel Economy Calculations Example 1: An electric vehicle is...

  15. 75 FR 59673 - Public Hearing Locations for the Proposed Fuel Economy Labels

    Science.gov (United States)

    2010-09-28

    ...] RIN 2060-AQ09; RIN 2127-AK73 Public Hearing Locations for the Proposed Fuel Economy Labels AGENCY... Vehicle Fuel Economy Label,'' published in the Federal Register on September 23, 2010. The goal of a... testimony or comment on the Agency's proposed revisions and additions to the motor vehicle fuel economy...

  16. 40 CFR 600.206-93 - Calculation and use of fuel economy values for gasoline-fueled, diesel-fueled, electric, alcohol...

    Science.gov (United States)

    2010-07-01

    ... EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-Procedures... equivalent petroleum-based fuel economy value exists for an electric vehicle configuration, all values for... values for gasoline-fueled, diesel-fueled, electric, alcohol-fueled, natural gas-fueled, alcohol dual...

  17. Survey evidence on the willingness of U.S. consumers to pay for automotive fuel economy

    International Nuclear Information System (INIS)

    Greene, David L.; Evans, David H.; Hiestand, John

    2013-01-01

    Prospect theory holds that human beings faced with a risky bet will tend to value potential losses about twice as much as potential gains. Previous research has demonstrated that prospect theory could be sufficient to explain an energy paradox in the market for automotive fuel economy. This paper analyzes data from questions added to four commercial, multi-client surveys of 1000 U.S. households each in 2004, 2011, 2012 and 2013. Households were asked about willingness to pay for future fuel savings as well as the annual fuel savings necessary to justify a given upfront payment. Payback periods inferred from household responses are generally consistent over time and across different formulations of questions. Mean calculated payback periods are about 3 years, but there is substantial dispersion among individual responses. The calculated payback periods do not appear to be correlated with the attributes of respondents. Respondents were able to quantitatively describe their uncertainty about both vehicle fuel economy and future fuel prices. Simulation of loss averse behavior based on respondents’ stated uncertainty illustrates how loss aversion could lead consumers to substantially undervalue future fuel savings relative to their expected value. - Highlights: • Payback periods were calculated from stated willingness to pay for fuel savings in 4 US surveys. • US car buyers expect payback in 3 years in order to pay more for increased fuel economy. • Respondents’ payback periods are uncorrelated with their socio-economic attributes. • Survey respondents consider fuel economy ratings and future fuel prices highly uncertain. • The survey results are consistent with the behavioral economic principle of loss aversion

  18. Fuel related risks; Braenslerisker

    Energy Technology Data Exchange (ETDEWEB)

    Englund, Jessica; Sernhed, Kerstin; Nystroem, Olle; Graveus, Frank (Grontmij AB, (Sweden))

    2012-02-15

    The project, within which this work report was prepared, aimed to complement the Vaermeforsk publication 'Handbook of fuels' on fuel related risks and measures to reduce the risks. The fuels examined in this project where the fuels included in the first version of the handbook from 2005 plus four additional fuels that will be included in the second and next edition of the handbook. Following fuels were included: woodfuels (sawdust, wood chips, powder, briquettes), slash, recycled wood, salix, bark, hardwood, stumps, straw, reed canary grass, hemp, cereal, cereal waste, olive waste, cocoa beans, citrus waste, shea, sludge, forest industrial sludge, manure, Paper Wood Plastic, tyre, leather waste, cardboard rejects, meat and bone meal, liquid animal and vegetable wastes, tall oil pitch, peat, residues from food industry, biomal (including slaughterhouse waste) and lignin. The report includes two main chapters; a general risk chapter and a chapter of fuel specific risks. The first one deals with the general concept of risk, it highlights laws and rules relevant for risk management and it discuss general risks that are related to the different steps of fuel handling, i.e. unloading, storing, processing the fuel, transportation within the facility, combustion and handling of ashes. The information that was used to produce this chapter was gathered through a literature review, site visits, and the project group's experience from risk management. The other main chapter deals with fuel-specific risks and the measures to reduce the risks for the steps of unloading, storing, processing the fuel, internal transportation, combustion and handling of the ashes. Risks and measures were considered for all the biofuels included in the second version in the handbook of fuels. Information about the risks and risk management was gathered through interviews with people working with different kinds of fuels in electricity and heat plants in Sweden. The information from

  19. Automotive Stirling engine development program. [fuel economy assessment

    Science.gov (United States)

    Kitzner, E. W.

    1978-01-01

    The Ford/DOE automotive Stirling engine development program is directed towards establishing the technological and developmental base that would enable a decision on whether an engineering program should be directed at Stirling engine production. The fuel economy assessment aims to achieve, with a high degree of confidence, the ERDA proposal estimate of 20.6 MPG (gasoline) for a 4500 lb 1WC Stirling engine passenger car. The current M-H fuel economy projection for the 170 HP Stirling engine is 15.7 MPG. The confidence level for this projection is 32%. A confidence level of 29% is projected for a 22.1 MPG estimate. If all of the planned analyses and test work is accomplished at the end of the one year effort, and the projected improvements are substantiated, the confidence levels would rise to 59% for the 20.6 MPG projection and 54% for the 22.1 MPG projection. Progress achieved thus far during the fuel economy assessment is discussed.

  20. Fuel Economy Improvement Potential of a Heavy Duty Truck using V2x Communication

    Energy Technology Data Exchange (ETDEWEB)

    LaClair, Tim J [ORNL; Verma, Rajeev [Eaton Corporation; Norris, Sarah [Eaton Corporation; Cochran, Robert [Eaton Corporation

    2014-01-01

    In this paper, we introduce an intelligent driver assistance system to reduce fuel consumption in heavy duty vehicles irrespective of the driving style of the driver. We specifically study the potential of V2I and V2V communications to reduce fuel consumption in heavy duty trucks. Most ITS communications today are oriented towards vehicle safety, with communications strategies and hardware that tend to focus on low latency. This has resulted in technologies emerging with a relatively limited range for the communications. For fuel economy, it is expected that most benefits will be derived with greater communications distances, at the scale of many hundred meters or several kilometers, due to the large inertia of heavy duty vehicles. It may therefore be necessary to employ different communications strategies for ITS applications aimed at fuel economy and other environmental benefits than what is used for safety applications in order to achieve the greatest benefits.

  1. Modeling of hybrid vehicle fuel economy and fuel engine efficiency

    Science.gov (United States)

    Wu, Wei

    "Near-CV" (i.e., near-conventional vehicle) hybrid vehicles, with an internal combustion engine, and a supplementary storage with low-weight, low-energy but high-power capacity, are analyzed. This design avoids the shortcoming of the "near-EV" and the "dual-mode" hybrid vehicles that need a large energy storage system (in terms of energy capacity and weight). The small storage is used to optimize engine energy management and can provide power when needed. The energy advantage of the "near-CV" design is to reduce reliance on the engine at low power, to enable regenerative braking, and to provide good performance with a small engine. The fuel consumption of internal combustion engines, which might be applied to hybrid vehicles, is analyzed by building simple analytical models that reflect the engines' energy loss characteristics. Both diesel and gasoline engines are modeled. The simple analytical models describe engine fuel consumption at any speed and load point by describing the engine's indicated efficiency and friction. The engine's indicated efficiency and heat loss are described in terms of several easy-to-obtain engine parameters, e.g., compression ratio, displacement, bore and stroke. Engine friction is described in terms of parameters obtained by fitting available fuel measurements on several diesel and spark-ignition engines. The engine models developed are shown to conform closely to experimental fuel consumption and motored friction data. A model of the energy use of "near-CV" hybrid vehicles with different storage mechanism is created, based on simple algebraic description of the components. With powertrain downsizing and hybridization, a "near-CV" hybrid vehicle can obtain a factor of approximately two in overall fuel efficiency (mpg) improvement, without considering reductions in the vehicle load.

  2. The Role of Synthetic Fuels for a Carbon Neutral Economy

    Directory of Open Access Journals (Sweden)

    Rui Namorado Rosa

    2017-04-01

    Full Text Available Fossil fuels depletion and increasing environmental impacts arising from their use call for seeking growing supplies from renewable and nuclear primary energy sources. However, it is necessary to simultaneously attend to both the electrical power needs and the specificities of the transport and industrial sector requirements. A major question posed by the shift away from traditional fossil fuels towards renewable energy sources lies in matching the power demand with the daily and seasonal oscillation and the intermittency of these natural energy fluxes. Huge energy storage requirements become necessary or otherwise the decline of the power factor of both the renewable and conventional generation would mean loss of resources. On the other hand, liquid and gaseous fuels, for which there is vast storage and distribution capacity available, appear essential to supply the transport sector for a very long time ahead, besides their domestic and industrial roles. Within this context, the present assessment suggests that proven technologies and sound tested principles are available to develop an integrated energy system, relying on synthetic fuels. These would incorporate carbon capture and utilization in a closed carbon cycle, progressively relying mostly on solar and/or nuclear primary sources, providing both electric power and gaseous/liquid hydrocarbon fuels, having ample storage capacity, and able to timely satisfy all forms of energy demand. The principles and means are already available to develop a carbon-neutral synthetic fuel economy.

  3. 40 CFR 600.113-12 - Fuel economy and carbon-related exhaust emission calculations for FTP, HFET, US06, SC03 and cold...

    Science.gov (United States)

    2010-07-01

    ... Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method... Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method... Petroleum Products by Hydrometer Method” (incorporated by reference at § 600.011-93) for the gasoline fuel...

  4. On the baseline evolution of automobile fuel economy in Europe

    International Nuclear Information System (INIS)

    Zachariadis, Theodoros

    2006-01-01

    'Business as usual' scenarios in long-term energy forecasts are crucial for scenario-based policy analyses. This article focuses on fuel economy of passenger cars and light trucks, a long-disputed issue with serious implications for worldwide energy use and CO 2 emissions. The current status in Europe is explained and future developments are analysed with the aid of historical data of the last three decades from the United States and Europe. As a result of this analysis, fuel economy values are proposed for use as assumptions in baseline energy/transport scenarios in the 15 'old' European Union Member States. Proposed values are given for new gasoline and diesel cars and for the years 2010, 2020 and 2030. The increasing discrepancy between vehicle fuel consumption measured under test conditions and that in the real world is also considered. One main conclusion is that the European Commission's voluntary agreement with the automobile industry should not be assumed to fully achieve its target under baseline conditions, nor should it be regarded as a major stimulus for autonomous vehicle efficiency improvements after 2010. A second conclusion is that three very recent studies enjoying authority across the EU tend to be overly optimistic as regards the technical progress for conventional and alternative vehicle propulsion technologies under 'business as usual' conditions

  5. Fuel economy and life-cycle cost analysis of a fuel cell hybrid vehicle

    Science.gov (United States)

    Jeong, Kwi Seong; Oh, Byeong Soo

    The most promising vehicle engine that can overcome the problem of present internal combustion is the hydrogen fuel cell. Fuel cells are devices that change chemical energy directly into electrical energy without combustion. Pure fuel cell vehicles and fuel cell hybrid vehicles (i.e. a combination of fuel cell and battery) as energy sources are studied. Considerations of efficiency, fuel economy, and the characteristics of power output in hybridization of fuel cell vehicle are necessary. In the case of Federal Urban Driving Schedule (FUDS) cycle simulation, hybridization is more efficient than a pure fuel cell vehicle. The reason is that it is possible to capture regenerative braking energy and to operate the fuel cell system within a more efficient range by using battery. Life-cycle cost is largely affected by the fuel cell size, fuel cell cost, and hydrogen cost. When the cost of fuel cell is high, hybridization is profitable, but when the cost of fuel cell is less than 400 US$/kW, a pure fuel cell vehicle is more profitable.

  6. Fuel Economy Impacts of Manual, Conventional Cruise Control, and Predictive Eco-Cruise Control Driving

    Directory of Open Access Journals (Sweden)

    Sangjun Park

    2013-09-01

    Full Text Available The paper presents the results of a field experiment that was designed to compare manual driving, conventional cruise control (CCC driving, and Eco-cruise control (ECC driving with regard to fuel economy. The field experiment was conducted on five test vehicles along a section of Interstate 81 that was comprised of ±4% uphill and downhill grade sections. Using an Onboard Diagnostic II reader, instantaneous fuel consumption rates and other driving parameters were collected with and without the CCC system enabled. The collected data were compared with regard to fuel economy, throttle control, and travel time. The results demonstrate that CCC enhances vehicle fuel economy by 3.3 percent on average relative to manual driving, however this difference was not found to be statistically significant at a 5 percent significance level. The results demonstrate that CCC driving is more efficient on downhill versus uphill sections. In addition, the study demonstrates that an ECC system can produce fuel savings ranging between 8 and 16 percent with increases in travel times ranging between 3 and 6 percent. These benefits appear to be largest for heavier vehicles (SUVs.

  7. 40 CFR 600.307-95 - Fuel economy label format requirements.

    Science.gov (United States)

    2010-07-01

    ... requirements. (a)(1) Fuel economy labels must be: (i) Rectangular in shape with a minimum height of 4.5 inches... equivalent fuel economy. To convert these values into units of miles per 100 cubic feet of natural gas... per 100 cubic feet of natural gas, multiply by 0.823.” may be replaced by the statement “The fuel...

  8. Household cooking fuels and technologies in developing economies

    International Nuclear Information System (INIS)

    Foell, Wesley; Pachauri, Shonali; Spreng, Daniel; Zerriffi, Hisham

    2011-01-01

    A major energy challenge of the 21st century is the health and welfare of 2.7 billion people worldwide, who currently rely on burning biomass in traditional household cooking systems. This Special Issue on Clean Cooking Fuels and Technologies in Developing Economies builds upon an IAEE workshop on this subject, held in Istanbul in 2008. It includes several papers from that workshop plus papers commissioned afterwards. The major themes of that workshop and this Special Issue are: •Analytical and decision frameworks for analysis and policy development for clean cooking fuels. •Making energy provisioning a central component of development strategies. •Strategies/business models of suppliers of modern fuels and technologies. •Analysis of successes/failures of past policies and programs to improve access to clean cooking. This introductory paper serves as a preamble to the 11 papers in this Special Issue. It provides a brief background on household cooking fuels and technologies, including: (1) their implications for sustainable development, health and welfare, gender impacts, and environment/climate issues; (2) options and scenarios for improved household cooling systems; and (3) discussions of institutions, programs and markets. It closes with “Research and Action Agendas”, initially developed during the 2008 workshop.

  9. Fuel cell commercialization: The key to a hydrogen economy

    Science.gov (United States)

    Zegers, P.

    With the current level of global oil production, oil reserves will be sufficient for 40 years. However, due to the fact that the global GDP will have increased by a factor seven in 2050, oil reserves are likely to be exhausted in a much shorter time period. The EU and car industry aim at a reduction of the consumption of oil, at energy savings (with a key role for fuel cells) and an increased use of hydrogen from natural gas and, possibly, coal, in the medium term. The discovery of huge methane resources as methane hydrates (20 times those of oil, gas and coal together) in oceans at 1000-3000 m depth could be of major importance. In the long term, the EU aims at a renewable energy-based energy supply. The European Hydrogen and Fuel Cell Technology Platform is expected to play a major role in bringing about a hydrogen economy. The availability of commercial fuel cells is here a prerequisite. However, after many years of research, fuel cells have not yet been commercialized. If they will not succeed to enter the market within 5 years there is a real danger that activities aiming at a hydrogen society will peter out. In a hydrogen strategy, high priority should therefore be given to actions which will bring about fuel cell commercialization within 5 years. They should include the identification of fuel cell types and (niche) markets which are most favorable for a rapid market introduction. These actions should include focused short-term RTD aiming at cost reduction and increased reliability.

  10. Clean Cities Strategic Planning White Paper: Light Duty Vehicle Fuel Economy

    Energy Technology Data Exchange (ETDEWEB)

    Saulsbury, Bo [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hopson, Dr Janet L [Univ. of Tennessee, Knoxville, TN (United States); Greene, David [Univ. of Tennessee, Knoxville, TN (United States); Gibson, Robert [Univ. of Tennessee, Knoxville, TN (United States)

    2015-04-01

    Increasing the energy efficiency of motor vehicles is critical to achieving national energy goals of reduced petroleum dependence, protecting the global climate, and promoting continued economic prosperity. Even with fuel economy and greenhouse gas emissions standards and various economic incentives for clean and efficient vehicles, providing reliable and accurate fuel economy information to the public is important to achieving these goals. This white paper reviews the current status of light-duty vehicle fuel economy in the United States and the role of the Department of Energy (DOE) Clean Cities Program in disseminating fuel economy information to the public.

  11. 40 CFR 600.207-08 - Calculation and use of vehicle-specific 5-cycle-based fuel economy values for vehicle...

    Science.gov (United States)

    2010-07-01

    ...-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year... for each vehicle under § 600.114-08 and as approved in § 600.008-08 (c), are used to determine vehicle... fuel economy value exists for an electric vehicle configuration, all values for that vehicle...

  12. Light-duty vehicle greenhouse gas emission standards and corporate average fuel economy standards : final rule

    Science.gov (United States)

    2010-05-07

    Final Rule to establish a National Program consisting of new standards for light-duty vehicles that will reduce greenhouse gas emissions and improve fuel economy. This joint : Final Rule is consistent with the National Fuel Efficiency Policy announce...

  13. The Sport-Utility Vehicle: Debating Fuel-Economy Standards in Thermodynamics

    Science.gov (United States)

    Mayer, Shannon

    2008-01-01

    This paper describes a debate about national fuel-economy standards for sport-utility vehicles (SUVs) used as a foundation for exploring a public policy issue in the physical science classroom. The subject of automobile fuel economy benefits from a familiarity with thermodynamics, specifically heat engines, and is therefore applicable to a broad…

  14. Real-world fuel economy and CO{sub 2} emissions of plug-in hybrid electric vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Ploetz, Patrick; Funke, Simon Arpad; Jochem, Patrick [Fraunhofer-Institut fuer System- und Innovationsforschung (ISI), Karlsruhe (Germany). Competence Center Energiepolitik und Energiesysteme

    2015-07-01

    Plug-in hybrid electric vehicles (PHEV) combine electric propulsion with an internal combustion engine. Their potential to reduce transport related green-house gas emissions highly depends on their actual usage and electricity provision. Various studies underline their environmental and economic advantages, but are based on standardised driving cycles, simulations or small PHEV fleets. Here, we analyse real-world fuel economy of PHEV and the factors influencing it based on about 2,000 actual PHEV that have been observed over more than a year in the U.S. and Germany. We find that real-world fuel economy of PHEV differ widely among users. The main factors explaining this variation are the annual mileage, the regularity of daily driving, and the likelihood of long-distance trips. Current test cycle fuel economy ratings neglect these factors. Despite the broad range of PHEV fuel economies, the test cycle fuel economy ratings can be close to empiric PHEV fleet averages if the average annual mile-age is about 17,000 km. For the largest group of PHEV in our data, the Chevrolet Volt, we find the average fuel economy to be 1.45 litres/100 km at an average electric driving share of 78%. The resulting real-world tank-to-wheel CO{sub 2} emissions of these PHEV are 42 gCO{sub 2}/km and the annual CO{sub 2} savings in the U.S. amount to about 50 Mt. In conclusion, the variance of empirical PHEV fuel economy is considerably higher than of conventional vehicles. This should be taken into account by future test cycles and high electric driving shares should be incentivised.

  15. Feebates, rebates and gas-guzzler taxes: a study of incentives for increased fuel economy

    International Nuclear Information System (INIS)

    Greene, D.L.; Patterson, P.D.; Singh, Margaret; Li Jia

    2005-01-01

    US fuel economy standards have not been changed significantly in 20 years. Feebates are a market-based alternative in which vehicles with fuel consumption rates above a 'pivot point' are charged fees while vehicles below receive rebates. By choice of pivot points, feebate systems can be made revenue neutral. Feebates have been analyzed before. This study re-examines feebates using recent data, assesses how the undervaluing of fuel economy by consumers might affect their efficacy, tests sensitivity to the cost of fuel economy technology and price elasticities of vehicle demand, and adds assessments of gas-guzzler taxes or rebates alone. A feebate rate of $500 per 0.01 gallon per mile (GPM) produces a 16 percent increase in fuel economy, while a $1000 per 0.01 GPM results in a 29 percent increase, even if consumers count only the first 3 years of fuel savings. Unit sales decline by about 0.5 percent but sales revenues increase because the added value of fuel economy technologies outweighs the decrease in sales. In all cases, the vast majority of fuel economy increase is due to adoption of fuel economy technologies rather than shifts in sales

  16. Fuel economy of new passenger cars in Mexico: Trends from 1988 to 2008 and prospects

    International Nuclear Information System (INIS)

    Sheinbaum-Pardo, Claudia; Chávez-Baeza, Carlos

    2011-01-01

    This paper analyzes trends in fuel economy (kilometers per liter) of new passenger vehicles in Mexico over a period of 20 years from 1988 to 2008. Results show that in this period, fuel economy of the new passenger vehicle fleet, including multipurpose vehicles (a category similar to sport utility vehicles, SUVs), increased by only 6.3%. A simple Laspeyres index analysis was developed to evaluate both the impact of changes in vehicle sales structure by category and the changes in fuel economy. Results show that increased sales of heavier, multipurpose vehicles in place of subcompact and compact vehicles, impacted negatively on the fleet average fuel economy. If the structure of sales had continued in the same proportions across all categories as in 1988, fuel economy would have increased by 11.0%, instead of the actual 6.3%. This result coincides with trends in other countries. The paper also presents different scenarios of passenger car fuel economy for the year 2020, and its implications for gasoline consumption and CO 2 emissions. The results may influence the new passenger vehicle fuel economy standard that is currently under discussion in Mexico.

  17. 75 FR 25323 - Light-Duty Vehicle Greenhouse Gas Emission Standards and Corporate Average Fuel Economy Standards...

    Science.gov (United States)

    2010-05-07

    ... Greenhouse Gas Emission Standards and Corporate Average Fuel Economy Standards; Final Rule #0;#0;Federal... Fuel Economy Standards; Final Rule AGENCY: Environmental Protection Agency (EPA) and National Highway... reduce greenhouse gas emissions and improve fuel economy. This joint Final Rule is consistent with the...

  18. 41 CFR 102-34.65 - How may we request an exemption from the fuel economy standards?

    Science.gov (United States)

    2010-07-01

    ... exemption from the fuel economy standards? 102-34.65 Section 102-34.65 Public Contracts and Property... an exemption from the fuel economy standards? You must submit a written request for an exemption from the fuel economy standards to: Administrator, General Services Administration, ATTN: Deputy Associate...

  19. Impact of non-petroleum vehicle fuel economy on GHG mitigation potential

    International Nuclear Information System (INIS)

    Luk, Jason M; Saville, Bradley A; MacLean, Heather L

    2016-01-01

    The fuel economy of gasoline vehicles will increase to meet 2025 corporate average fuel economy standards (CAFE). However, dedicated compressed natural gas (CNG) and battery electric vehicles (BEV) already exceed future CAFE fuel economy targets because only 15% of non-petroleum energy use is accounted for when determining compliance. This study aims to inform stakeholders about the potential impact of CAFE on life cycle greenhouse gas (GHG) emissions, should non-petroleum fuel vehicles displace increasingly fuel efficient petroleum vehicles. The well-to-wheel GHG emissions of a set of hypothetical model year 2025 light-duty vehicles are estimated. A reference gasoline vehicle is designed to meet the 2025 fuel economy target within CAFE, and is compared to a set of dedicated CNG vehicles and BEVs with different fuel economy ratings, but all vehicles meet or exceed the fuel economy target due to the policy’s dedicated non-petroleum fuel vehicle incentives. Ownership costs and BEV driving ranges are estimated to provide context, as these can influence automaker and consumer decisions. The results show that CNG vehicles that have lower ownership costs than gasoline vehicles and BEVs with long distance driving ranges can exceed the 2025 CAFE fuel economy target. However, this could lead to lower efficiency CNG vehicles and heavier BEVs that have higher well-to-wheel GHG emissions than gasoline vehicles on a per km basis, even if the non-petroleum energy source is less carbon intensive on an energy equivalent basis. These changes could influence the effectiveness of low carbon fuel standards and are not precluded by the light-duty vehicle GHG emissions standards, which regulate tailpipe but not fuel production emissions. (letter)

  20. Fuel Cell Development for NASA's Human Exploration Program: Benchmarking with "The Hydrogen Economy"

    Science.gov (United States)

    Scott, John H.

    2007-01-01

    The theoretically high efficiency and low temperature operation of hydrogen-oxygen fuel cells has motivated them to be the subject of much study since their invention in the 19th Century, but their relatively high life cycle costs kept them as a "solution in search of a problem" for many years. The first problem for which fuel cells presented a truly cost effective solution was that of providing a power source for NASA's human spaceflight vehicles in the 1960 s. NASA thus invested, and continues to invest, in the development of fuel cell power plants for this application. This development program continues to place its highest priorities on requirements for minimum system mass and maximum durability and reliability. These priorities drive fuel cell power plant design decisions at all levels, even that of catalyst support. However, since the mid-1990's, prospective environmental regulations have driven increased governmental and industrial interest in "green power" and the "Hydrogen Economy." This has in turn stimulated greatly increased investment in fuel cell development for a variety of commercial applications. This investment is bringing about notable advances in fuel cell technology, but, as these development efforts place their highest priority on requirements for minimum life cycle cost and field safety, these advances are yielding design solutions quite different at almost every level from those needed for spacecraft applications. This environment thus presents both opportunities and challenges for NASA's Human Exploration Program

  1. The Impact of Drive Cycles and Auxiliary Power on Passenger Car Fuel Economy

    Directory of Open Access Journals (Sweden)

    Thomas Grube

    2018-04-01

    Full Text Available In view of the advancement of zero emission transportation and current discussions on the reliability of nominal passenger car fuel economy, this article considers the procedure for assessing the potential for reducing the fuel consumption of passenger cars by using electric power to operate them. The analysis compares internal combustion engines, hybrid and fully electric concepts utilizing batteries and fuel cells. The starting point for the newly developed, simulation-based fuel consumption analysis is a longitudinal vehicle model. Mechanical power requirements on the drive side incorporate a large variety of standardized drive cycles to simulate typical patterns of car usage. The power requirements of electric heating and air conditioning are also included in the simulation, as these are especially relevant to electric powertrains. Moreover, on-board grid-load profiles are considered in the assessment. Fuel consumption is optimized by applying concept-specific operating strategies. The results show that the combination of low average driving speed and elevated onboard power requirements have severe impacts on the fuel efficiency of all powertrain configurations analyzed. In particular, the operational range of battery-electric vehicles is strongly affected by this due to the limited storage capacity of today’s batteries. The analysis confirms the significance of considering different load patterns of vehicle usage related to driving profiles and onboard electrical and thermal loads.

  2. In-use fuel economy of hybrid-electric school buses in Iowa.

    Science.gov (United States)

    Hallmark, Shauna; Sperry, Bob; Mudgal, Abhisek

    2011-05-01

    Although it is much safer and more fuel-efficient to transport children to school in buses than in private vehicles, school buses in the United States still consume 822 million gal of diesel fuel annually, and school transportation costs can account for a significant portion of resource-constrained school district budgets. Additionally, children in diesel-powered school buses may be exposed to higher levels of particulates and other pollutants than children in cars. One solution to emission and fuel concerns is use of hybrid-electric school buses, which have the potential to reduce emissions and overall lifecycle costs compared with conventional diesel buses. Hybrid-electric technologies are available in the passenger vehicle market as well as the transit bus market and have a track record indicating fuel economy and emissions benefits. This paper summarizes the results of an in-use fuel economy evaluation for two plug-in hybrid school buses deployed in two different school districts in Iowa. Each school district selected a control bus with a route similar to that of the hybrid bus. Odometer readings, fuel consumption, and maintenance needs were recorded for each bus. The buses were deployed in 2008 and data were collected through May 2010. Fuel consumption was calculated for each school district. In Nevada, IA, the overall average fuel economy was 8.23 mpg for the hybrid and 6.35 mpg for the control bus. In Sigourney, IA, the overall average fuel economy was 8.94 mpg for the hybrid and 6.42 mpg for the control bus. The fuel consumption data were compared for the hybrid and control buses using a Wilcoxon signed rank test. Results indicate that fuel economy for the Nevada hybrid bus was 29.6% better than for the Nevada control bus, and fuel economy for the Sigourney hybrid bus was 39.2% higher than for the Sigourney control bus. Both differences were statistically significant.

  3. Unemployment rate and price of gasoline predict the fuel economy of purchased new vehicles.

    Science.gov (United States)

    2011-03-01

    This study examined the relationship between two economic indicatorsthe : unemployment rate and the price of gasolineand the fuel economy of purchased new : vehicles. A regression analysis was performed on U.S. monthly data from October 2007 : ...

  4. Increasing the Fuel Economy and Safety of New Light-DutyVehicles

    Energy Technology Data Exchange (ETDEWEB)

    Wenzel, Tom; Ross, Marc

    2006-09-18

    One impediment to increasing the fuel economy standards forlight-duty vehicles is the long-standing argument that reducing vehiclemass to improve fuel economy will inherently make vehicles less safe.This technical paper summarizes and examines the research that is citedin support of this argument, and presents more recent research thatchallenges it. We conclude that the research claiming that lightervehicles are inherently less safe than heavier vehicles is flawed, andthat other aspects of vehicle design are more important to the on-roadsafety record of vehicles. This paper was prepared for a workshop onexperts in vehicle safety and fuel economy, organized by the William andFlora Hewlett Foundation, to discuss technologies and designs that can betaken to simultaneously improve vehicle safety and fuel economy; theworkshop was held in Washington DC on October 3, 2006.

  5. Policy Pathways: Improving the Fuel Economy of Road Vehicles - A policy package

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-07-01

    The transportation sector accounts for approximately one-fifth of global final energy consumption and will account for nearly all future growth in oil use, particularly for road vehicles. The right policy mix can allow countries to improve the fuel economy of road vehicles, which in turn can enhance energy security and reduce CO2 emissions. Improving the Fuel Economy of Road Vehicles highlights lessons learned and examples of good practices from countries with experience in implementing fuel economy policies for vehicles. The report, part of the IEA’s Policy Pathway series, outlines key steps in planning, implementation, monitoring and evaluation. It complements the IEA Technology Roadmap: Fuel Economy for Road Vehicles, which outlines technical options, potentials, and costs towards improvement in the near, medium and long term.

  6. Light-Duty Automotive Technology, Carbon Dioxide Emissions, and Fuel Economy Trends Data

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Light-Duty Automotive Technology, Carbon Dioxide Emissions, and Fuel Economy Trends report is the authoritative reference for carbon dioxide (CO2) emissions,...

  7. Eco-driving : strategic, tactical, and operational decisions of the driver that improve vehicle fuel economy.

    Science.gov (United States)

    2011-08-01

    "This report presents information about the effects of decisions that a driver can make to : influence on-road fuel economy of light-duty vehicles. These include strategic decisions : (vehicle selection and maintenance), tactical decisions (route sel...

  8. Potential Fuel Economy Improvements from the Implementation of cEGR and CDA on an Atkinson Cycle Engine

    Science.gov (United States)

    Present the implementation of cEGR and CDA on an Atkinson engine and use steady state fuel consumption maps to estimate the technologies’ potential fuel economy improvements over the FTP and Highway tests. In addition to use fuel weighted modes to determine possible fuel economy...

  9. Is self-repayment of the nuclear fuel cycle plants profitable for national economy?

    International Nuclear Information System (INIS)

    Shevelev, Ya.V.

    1991-01-01

    The nuclear fuel cycle (NFC) plants should not be repaying in the optimal plan of nuclear economy development. Their losses are overlapped by superprofits of energy consumers. The loss in the national economy resulting from compulsory conversion of the NFC plants to self-repayment is estimated. 12 refs

  10. The relation between energy - ecology - economy

    International Nuclear Information System (INIS)

    Horn, J.

    1977-01-01

    In North America and Western Europe, supporters of zero growth think that economy and energy, on the one hand, and an intact ecology, on the other, are opposites or opposing tendencies which cannot go hand in hand. These people also contest the claim that there is a linear correlation between a developing ecology and technology and increased energy consumption. The author thinks that the above basic assumptions are wrong and not in agreement with either the laws of evolution of the geosphere or with the necessities of the present political and economic situation. Giving an outline of the history of evolution and the present situation, especially in the developing countries, he shows that there is a linear, self-strengthening correlation between economic growth and capital-intensive technological innovation on the one hand and environmental improvement on the other. (orig./GG) [de

  11. Forest fuel - economy and models for cost analysis

    International Nuclear Information System (INIS)

    Olsson, Anders.

    1991-01-01

    The purpose of this report is to develop guidelines for the R and D work within Skogskraft with the aim of improving the efficiency of the investigatory work. The report mainly concerns logging waste. The contents are as follows; Terminology - definitions: This section includes a brief description of wood fuels with regard to terminology, definitions, production and marketing. Units of measurement: Different units of measurement are descrived and their relationship to forestry, sawmills and consumers of wood fuels. An account is also given of effective thermal values and formulas for calculations of the energy content for different wood fuels. Calculation models, analyses: This section discusses different models and standards for calculating machine and manual costs. In addition, views are given on cost analysis and certain guidelines with regard to overhead costs. Actors and systems: There is a risk that technical problems receive a far too dominant role in relation to problems which concern organisation and structure. Consequently, it is important to define the actors and to illustrate the different driving forces and tensions that may occur. Seven different actors/interested parties have been described and analysed with regard to primary and secondary interests in ecological, technical and economic questions. Preparation of reports: Certain recommendations have been given with regard to formal requirements and quality requirements

  12. Experiment and Simulation of Medium-Duty Tactical Truck for Fuel Economy Improvement

    Directory of Open Access Journals (Sweden)

    Allen M. Quail

    2011-02-01

    Full Text Available Fuel economy improvement on medium-duty tactical truck has and continues to be a significant initiative for the U.S. Army. The focus of this study is the investigation of Automated Manual Transmissions (AMT and mild hybridization powertrain that have potential to improve the fuel economy of the 2.5-ton cargo trucks. The current platform uses a seven-speed automatic transmission. This study utilized a combination of on-road experimental vehicle data and analytical vehicle modeling and simulation. This paper presents the results of (1 establishment of a validated, high fidelity baseline analytical vehicle model, (2 modeling and simulation of two AMTs and their control strategy, (3 optimization of transmissions shift schedules, and (4 modeling and simulation of engine idle stop/start and Belt-Integrated-Starter-Generator (B-ISG systems to improve the fuel economy. The fuel economy discrepancy between experimental average and the baseline simulation result was 2.87%. The simulation results indicated a 14.5% and 12.2% fuel economy improvement for the 10-speed and 12-speed AMT respectively. A stop/start system followed by a B-ISG mild hybrid system incorporating regenerative braking was estimated to improve fuel economy 3.39% and 10.2% respectively.

  13. Meeting U.S. passenger vehicle fuel economy standards in 2016 and beyond

    International Nuclear Information System (INIS)

    Cheah, Lynette; Heywood, John

    2011-01-01

    New fuel economy standards require new U.S. passenger vehicles to achieve at least 34.1 miles per gallon (MPG) on average by model year 2016, up from 28.8 MPG today. In this paper, the magnitude, combinations and timings of the changes required in U.S. vehicles that are necessary in order to meet the new standards, as well as a target of doubling the fuel economy within the next two decades are explored. Scenarios of future vehicle characteristics and sales mix indicate that the 2016 mandate is aggressive, requiring significant changes starting from today. New vehicles must forgo horsepower improvements, become lighter, and a greater number will use advanced, more fuel-efficient powertrains, such as smaller turbocharged engines, hybrid-electric drives. Achieving a factor-of-two increase in fuel economy by 2030 is also challenging, but more feasible since the auto industry will have more lead time to respond. A discussion on the feasibility of meeting the new fuel economy mandate is included, considering vehicle production planning realities and challenges in deploying new vehicle technologies into the market. - Research Highlights: → The new 2016 fuel economy standards for passenger vehicles in the U.S. can be met, but are aggressive. → Future vehicles must forgo horsepower improvements, become lighter, and a greater number will use advanced, more fuel efficient powertrains. → The challenge of meeting the fuel economy targets is defined by both the magnitude and the timing of these requirements. → Doubling the fuel economy by 2030 is also challenging, but more feasible since the auto industry will have more lead time to respond.

  14. Hydrogen Fuel Cell Vehicle Fuel Economy Testing at the U.S. EPA National Vehicle and Fuel Emissions Laboratory (SAE Paper 2004-01-2900)

    Science.gov (United States)

    The introduction of hydrogen fuel cell vehicles and their new technology has created the need for development of new fuel economy test procedures and safety procedures during testing. The United States Environmental Protection Agency-National Vehicle Fuels and Emissions Laborato...

  15. Determining Off-Cycle Fuel Economy Benefits of 2-Layer HVAC Technology

    Energy Technology Data Exchange (ETDEWEB)

    Wood, Eric W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Moniot, Matthew [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Jehlik, Forrest [Argonne National Laboratory; Chevers, Netsanet [Toyota Motor North America R& D; Hirabayshi, Hidekazu [Toyota Motor North America R& D; Song, Yuanpei [DENSO International America Inc.

    2018-04-03

    This work presents a methodology to determine the off-cycle fuel economy benefit of a 2-Layer HVAC system which reduces ventilation and heat rejection losses of the heater core versus a vehicle using a standard system. Experimental dynamometer tests using EPA drive cycles over a broad range of ambient temperatures were conducted on a highly instrumented 2016 Lexus RX350 (3.5L, 8 speed automatic). These tests were conducted to measure differences in engine efficiency caused by changes in engine warmup due to the 2-Layer HVAC technology in use versus the technology being disabled (disabled equals fresh air-considered as the standard technology baseline). These experimental datasets were used to develop simplified response surface and lumped capacitance vehicle thermal models predictive of vehicle efficiency as a function of thermal state. These vehicle models were integrated into a database of measured on road testing and coupled with U.S. typical meteorological data to simulate vehicle efficiency across seasonal thermal and operational conditions for hundreds of thousands of drive cycles. Fuel economy benefits utilizing the 2-Layer HVAC technology are presented in addition to goodness of fit statistics of the modeling approach relative to the experimental test data.

  16. From user-producer relations to the learning economy

    DEFF Research Database (Denmark)

    Johnson, Bjørn

    2011-01-01

    This paper deals with three issues. First, the conceptual and theoretical development in Lundvall’s writing from user–producer relations to the learning economy is discussed with a focus on his main contributions to innovation theory. Second, Lundvall’s description of the learning economy...... the learning economy is placed as a central concept in the quest for a general theory of innovation, which for many years has characterized Lundvall’s writings....... is extended in that it is argued that it is driven by its internal contradictions, and by the institutional responses to these contradictions. This approach is not in conflict with Lundvall’s views, but he has not pursued it and it may give new insights into the dynamics of the learning economy. Finally...

  17. The cost of fuel economy in the Indian passenger vehicle market

    International Nuclear Information System (INIS)

    Chugh, Randy; Cropper, Maureen; Narain, Urvashi

    2011-01-01

    To investigate how fuel economy is valued in the Indian car market, we compute the cost to Indian consumers of purchasing a more fuel-efficient vehicle and compare it to the benefit of lower fuel costs over the life of the vehicle. We estimate hedonic price functions for four market segments (petrol hatchbacks, diesel hatchbacks, petrol sedans, and diesel sedans) to compute 95% confidence intervals for the marginal cost to the consumer for an increase in fuel economy. We find that the associated present value of fuel savings falls within the 95% confidence interval for most specifications, in all market segments, for the years 2002 through 2006. Thus, we fail to consistently reject the hypothesis that consumers appropriately value fuel economy. - Highlights: → We examine the tradeoffs faced by new vehicle consumers in India. → We use hedonic price functions and instrumental variables. → We find no support for the hypothesis that consumers undervalue fuel economy. → Some consumers are willing to forgo substantial potential savings to own their preferred vehicle.

  18. Are standards effective in improving automobile fuel economy? An international panel analysis

    International Nuclear Information System (INIS)

    Clerides, Sofronis; Zachariadis, Theodoros

    2007-01-01

    Although the adoption of fuel economy standards has induced fuel savings in new motor vehicles, there are arguments against standards and in favour of fuel tax increases because the latter may have lower welfare costs. We therefore attempted to analyze the impact of standards and fuel prices in the fuel consumption of new cars with the aid of cross-section time series analysis of data from 18 countries. To our knowledge, this study is the first one that attempts to explore econometrically this issue at an international level. We built an unbalanced panel comprising 384 observations from the US, Canada, Australia, Japan, Switzerland and 13 EU countries spanning a period between 1975 and 2003. We specified a dynamic panel model of fuel economy and estimated the model for the whole sample and also for North America and Europe separately. Based on these estimates, we derived three important policy conclusions. Firstly, it seems that if there were no FE standards or voluntary targets in force, transportation energy use would increase more rapidly. Secondly, if CO 2 targets are not to be tightened in Europe, retail fuel prices might have to double in order to attain the currently discussed target of 120 g CO 2 /km in the future. Thirdly, without higher fuel prices and/or tighter FE standards, one should not expect any marked improvements in fuel economy under 'business as usual' conditions. European policy makers might need to consider this issue carefully because some recent European studies tend to be optimistic in this respect

  19. Reforming fossil fuel prices in India: Dilemma of a developing economy

    International Nuclear Information System (INIS)

    Anand, Mukesh Kumar

    2016-01-01

    Over the period between 1990–1 and 2012–3, fossil fuel use on farms has risen and its indirect use in farming, particularly for non-energy purposes, is also growing. Consequently, both energy intensity and fossil fuel intensity are rising for Indian agriculture. But, these are declining for the aggregate Indian economy. Thus, revision of fossil fuel prices acquires greater significance for Indian agriculture than for rest of the economy. There are significant differences across crops. The crop-level analysis is supplemented by an alternative approach that utilizes a three-sector input–output (I–O) model for the Indian economy representing farming, fossil fuels, and rest of economy. Fossil fuels sector is assessed to portray, in general, strong forward linkages. The increase in total cost of farming, for a given change in fossil fuel prices, is estimated as a multiple of increase in direct input cost of fossil fuels in farming. From the three-sector aggregated economy this multiple was estimated at 3.99 for 1998–9. But it grew to 6.7 in 2007–8. The findings have stronger ramifications than commonly recognized, for inflation and cost of implementing the policy on food security. - Highlights: •Fossil fuels’ contribution in primary energy supply has risen from 55 to 75 per cent. •Energy intensity halved for aggregate GDP, but doubled for agricultural GDP. •Impact of fossil fuel price increase on farming costs mimics a widening spiral. •Total cost of farming may increase 6.7 times the increase in direct fuel input cost.

  20. Demand for road-fuel in a small developing economy: The case of Sri Lanka

    International Nuclear Information System (INIS)

    Chandrasiri, Sunil

    2006-01-01

    This paper estimates the demand for road fuel (petrol and auto-diesel) in the context of a small developing economy-Sri Lanka. The data set covers a period of 39 years from 1964 to 2002 representing both close economy and open economy policy regimes. The estimation procedure is based on seemingly unrelated regression equation (SURE) methodology mainly to capture substitutability of petrol and diesel in road transportation. The effect of auto-fuel prices on vehicle demand is also analyzed as a part of the analysis. In addition to confirming existing evidence on road-fuel demand, the findings reveal some interesting evidence with respect to own-price elasticity, cross-price elasticity, lag effects, income and vehicle mix variables

  1. Innovation in the energy sector – The role of fossil fuels and developing economies

    International Nuclear Information System (INIS)

    Brutschin, Elina; Fleig, Andreas

    2016-01-01

    This paper analyzes the effects of fossil fuel rents on R&D expenditures and patent grants in the field of energy-related technology. We argue that an increasing share of fossil fuel rents lessens the innovation of new energy technologies. We consider a sample of countries beyond the common selection of OECD members and investigate innovation efforts in the energy sector of 116 countries from 1980 to 2012. We observe the gradually growing influence of resource-abundant countries on global R&D expenditures and find that increasing fossil fuel rents have a negative effect on patent grants. This study contributes to the ongoing debate concerning the potential effects of resource abundance. More importantly, it increases our understanding of innovation activities within the energy sector and further underscores the need to extend future research to countries that have not been taken into account thus far. - Highlights: • We investigate a sample of 116 countries, a pool beyond the commonly considered OECD members. • We find that high oil prices induce increased R&D expenditures in developed countries. • Fossil rents are associated with decreasing patent grants when developing economies are included. • We use multiple imputation to handle the problem of missing data.

  2. Interaction of carbon reduction and green energy promotion in a small fossil-fuel importing economy

    International Nuclear Information System (INIS)

    Pethig, Ruediger; Wittlich, Christian

    2009-01-01

    We study the incidence of carbon-reduction and green-energy promotion policies in an open fossil-fuel importing general equilibrium economy. The focus is on mixed price-based or quantity-based policies. Instruments directed toward promoting green energy are shown to reduce also carbon emissions and vice versa. Their direct effects are stronger than their side effects, the more so, the greater is the elasticity of substitution in consumption between energy and the consumption good. We calculate the effects of variations in individual policy parameters, especially on energy prices and welfare costs, and determine the impact of exogenous fossil-fuel price shocks on the economy. (orig.)

  3. Fuel economy and torque tracking in camless engines through optimization of neural networks

    International Nuclear Information System (INIS)

    Ashhab, Moh'd Sami S.

    2008-01-01

    The feed forward controller of a camless internal combustion engine is modeled by inverting a multi-input multi-output feed forward artificial neural network (ANN) model of the engine. The engine outputs, pumping loss and cylinder air charge, are related to the inputs, intake valve lift and closing timing, by the artificial neural network model, which is trained with historical input-output data. The controller selects the intake valve lift and closing timing that will mimimize the pumping loss and achieve engine torque tracking. Lower pumping loss means better fuel economy, whereas engine torque tracking gurantees the driver's torque demand. The inversion of the ANN is performed with the complex method constrained optimization. How the camless engine inverse controller can be augmented with adaptive techniques to maintain accuracy even when the engine parts degrade is discussed. The simulation results demonstrate the effectiveness of the developed camless engine controller

  4. Optimal Battery Utilization Over Lifetime for Parallel Hybrid Electric Vehicle to Maximize Fuel Economy

    Energy Technology Data Exchange (ETDEWEB)

    Patil, Chinmaya; Naghshtabrizi, Payam; Verma, Rajeev; Tang, Zhijun; Smith, Kandler; Shi, Ying

    2016-08-01

    This paper presents a control strategy to maximize fuel economy of a parallel hybrid electric vehicle over a target life of the battery. Many approaches to maximizing fuel economy of parallel hybrid electric vehicle do not consider the effect of control strategy on the life of the battery. This leads to an oversized and underutilized battery. There is a trade-off between how aggressively to use and 'consume' the battery versus to use the engine and consume fuel. The proposed approach addresses this trade-off by exploiting the differences in the fast dynamics of vehicle power management and slow dynamics of battery aging. The control strategy is separated into two parts, (1) Predictive Battery Management (PBM), and (2) Predictive Power Management (PPM). PBM is the higher level control with slow update rate, e.g. once per month, responsible for generating optimal set points for PPM. The considered set points in this paper are the battery power limits and State Of Charge (SOC). The problem of finding the optimal set points over the target battery life that minimize engine fuel consumption is solved using dynamic programming. PPM is the lower level control with high update rate, e.g. a second, responsible for generating the optimal HEV energy management controls and is implemented using model predictive control approach. The PPM objective is to find the engine and battery power commands to achieve the best fuel economy given the battery power and SOC constraints imposed by PBM. Simulation results with a medium duty commercial hybrid electric vehicle and the proposed two-level hierarchical control strategy show that the HEV fuel economy is maximized while meeting a specified target battery life. On the other hand, the optimal unconstrained control strategy achieves marginally higher fuel economy, but fails to meet the target battery life.

  5. 76 FR 39477 - Revisions and Additions to Motor Vehicle Fuel Economy Label

    Science.gov (United States)

    2011-07-06

    ...The Environmental Protection Agency (EPA) and the National Highway Traffic Safety Administration (NHTSA) are issuing a joint final rule establishing new requirements for the fuel economy and environment label that will be posted on the window sticker of all new automobiles sold in the U.S. The labeling requirements apply for model year 2013 and later vehicles with a voluntary manufacturer option for model year 2012. The labeling requirements apply to passenger cars, light-duty trucks, and medium duty passenger vehicles such as larger sport-utility vehicles and vans. The redesigned label provides expanded information to American consumers about new vehicle fuel economy and fuel consumption, greenhouse gas and smog-forming emissions, and projected fuel costs and savings, and also includes a smartphone interactive code that permits direct access to additional Web resources. Specific label designs are provided for gasoline, diesel, ethanol flexible fuel, compressed natural gas, electric, plug-in hybrid electric, and hydrogen fuel cell vehicles. This rulemaking is in response to provisions in the Energy Independence and Security Act of 2007 that imposed several new labeling requirements and new advanced-technology vehicles entering the market. NHTSA and EPA believe that these changes will help consumers to make more informed vehicle purchase decisions, particularly as the future automotive marketplace provides more diverse vehicle technologies from which consumers may choose. These new label requirements do not affect the methodologies that EPA uses to generate consumer fuel economy estimates, or the automaker compliance values for NHTSA's corporate average fuel economy and EPA's greenhouse gas emissions standards. This action also finalizes a number of technical corrections to EPA's light-duty greenhouse gas emission standards program.

  6. Economy

    OpenAIRE

    Haring, Ben

    2009-01-01

    The economy of ancient Egypt is a difficult area of study due to the lack of preservation of much data (especially quantitative data); it is also a controversial subject on which widely divergent views have been expressed. It is certain, however, that the principal production and revenues of Egyptian society as a whole and of its individual members was agrarian, and as such, dependent on the yearly rising and receding of the Nile. Most agricultural producers were probably self-sufficient tena...

  7. The Transportation Leapfrog: Using Smart Phones to Collect Driving Data and Model Fuel Economy in India

    Energy Technology Data Exchange (ETDEWEB)

    Gopal, Anand [Lawrence Berkeley National Laboratory (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Schewel, Laura [Lawrence Berkeley National Laboratory (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Saxena, Samveg [Lawrence Berkeley National Laboratory (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Phadke, Amol [Lawrence Berkeley National Laboratory (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division

    2013-05-01

    Car ownership in India is expected to skyrocket in the coming decades, strongly driven by rising incomes. This phenomenon provides unprecedented opportunities for automakers and equally unprecedented social and environmental challenges. Policymakers, urban planners and civil society see this car boom leading to an explosion in problems related to congestion, infrastructure, air pollution, safety, higher oil imports and climate change. For all these stakeholders to take effective action, good data on how people use their cars, their demand for mobility and their behavior in mobility is essential. Unfortunately, there is very little data on the Indian transport sector as a whole and virtually none on real-world vehicle performance and use. The rapid development of high quality mobile telecommunications infrastructure provides India with the opportunity to leapfrog the West in cheaply collecting vast amounts of useful data from transportation. In this paper, we describe a pilot project in which we use commercial smart phone apps to collect per second car driving data from the city of Pune, instantly upload it through 3G and prepare it for analysis using advanced noise filtering algorithms for less than $1 per day per car. We then use our data in an Autonomie simulation to show that India’s currently planned fuel economy test procedures will result in over-estimates of fuel economy of approximately 35% for a typical Indian car when it is operated in real world conditions. Supporting better driving cycle development is just one of many applications for smart phone derived data in Indian transportation.

  8. 40 CFR 600.207-86 - Calculation of fuel economy values for a model type.

    Science.gov (United States)

    2010-07-01

    ... calculation of the original base level fuel economy values), and (iii) All subconfigurations within the new... a new base level. The new base level is identical to the existing base level except that it shall be considered, for the purposes of this paragraph, as containing a new basic engine. The manufacturer will be...

  9. 40 CFR 600.207-93 - Calculation of fuel economy values for a model type.

    Science.gov (United States)

    2010-07-01

    ... calculation of the original base level fuel economy values); and (iii) All subconfigurations within the new... a new base level. The new base level is identical to the existing base level except that it shall be considered, for the purposes of this paragraph, as containing a new basic engine. The manufacturer will be...

  10. Impact of Friction Reduction Technologies on Fuel Economy for Ground Vehicles

    Science.gov (United States)

    2009-08-13

    UNCLAS: Dist A. Approved for public release IMPACT OF FRICTION REDUCTION TECHNOLOGIES ON FUEL ECONOMY FOR GROUND VEHICLES G. R. Fenske , R. A. Erck...PROGRAM ELEMENT NUMBER 6. AUTHOR(S) G.R. Fenske ; R.A. Erck; O.O. Ajayi; A. Masoner’ A.S. Confort 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT

  11. Vehicle energy management for on/off controlled auxiliaries : fuel economy vs. switching frequency

    NARCIS (Netherlands)

    Chen, H.; Kessels, J.T.B.A.; Weiland, S.

    2015-01-01

    In this paper, an integrated approach for designing energy management strategies concerning vehicle auxiliaries with on/off control is proposed. This approach provides the possibility of making different trade-offs between fuel economy and switching frequency. In this paper, we demonstrate the

  12. 40 CFR 600.307-86 - Fuel economy label format requirements.

    Science.gov (United States)

    2010-07-01

    ... metering system, including number of carburetor barrels, if applicable; (7) Transmission class; (8... Regulations for 1977 and Later Model Year Automobiles-Labeling § 600.307-86 Fuel economy label format... the city and highway estimates by 0.85, then rounding to the next lower integer value. (2) The upper...

  13. Simulations of the Fuel Economy and Emissions of Hybrid Transit Buses over Planned Local Routes

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Zhiming [ORNL; LaClair, Tim J [ORNL; Daw, C Stuart [ORNL; Smith, David E [ORNL; Franzese, Oscar [ORNL

    2014-01-01

    We present simulated fuel economy and emissions city transit buses powered by conventional diesel engines and diesel-hybrid electric powertrains of varying size. Six representative city drive cycles were included in the study. In addition, we included previously published aftertreatment device models for control of CO, HC, NOx, and particulate matter (PM) emissions. Our results reveal that bus hybridization can significantly enhance fuel economy by reducing engine idling time, reducing demands for accessory loads, exploiting regenerative braking, and shifting engine operation to speeds and loads with higher fuel efficiency. Increased hybridization also tends to monotonically reduce engine-out emissions, but trends in the tailpipe (post-aftertreatment) emissions involve more complex interactions that significantly depend on motor size and drive cycle details.

  14. Towards a methanol economy: Zeolite catalyzed production of synthetic fuels

    DEFF Research Database (Denmark)

    Mentzel, Uffe Vie

    The main focus of this thesis is zeolite catalyzed conversion of oxygenates to hydrocarbon fuels and chemicals. Furthermore, conversion of ethane to higher hydrocarbons has also been studied. After a brief introduction to the concept of “the methanol economy” in the first chapter, the second...... a commercial H-ZSM-5 zeolite impregnated with gallium and/or molybdenum is described. The object was to investigate if the presence of methanol in the feed could enhance the conversion of ethane, but in all cases the opposite is observed; the presence of methanol actually suppresses the conversion of ethane...... various zeolite catalysts is studied in Chapter 4. When 2-propanol or 1-butanol is converted over H-ZSM-5, the total conversion capacities of the catalyst are more than 25 times higher than for conversion of methanol and ethanol. Furthermore, for conversion of C3+ alcohols, the selectivity shifts during...

  15. 75 FR 58077 - Revisions and Additions to Motor Vehicle Fuel Economy Label

    Science.gov (United States)

    2010-09-23

    ...The Environmental Protection Agency (EPA) and the National Highway Traffic Safety Administration (NHTSA) are conducting a joint rulemaking to redesign and add information to the current fuel economy label that is posted on the window sticker of all new cars and light- duty trucks sold in the U.S. The redesigned label will provide new information to American consumers about the fuel economy and consumption, fuel costs, and environmental impacts associated with purchasing new vehicles beginning with model year 2012 cars and trucks. This action will also develop new labels for certain advanced technology vehicles, which are poised to enter the U.S. market, in particular plug-in hybrid electric vehicles and electric vehicles. NHTSA and EPA are proposing these changes because the Energy Independence and Security Act (EISA) of 2007 imposes several new labeling requirements, because the agencies believe that the current labels can be improved to help consumers make more informed vehicle purchase decisions, and because the time is right to develop new labels for advanced technology vehicles that are being commercialized. This proposal is also consistent with the recent joint rulemaking by EPA and NHTSA that established harmonized federal greenhouse gas (GHG) emissions and corporate average fuel economy (CAFE) standards for new cars, sport utility vehicles, minivans, and pickup trucks for model years 2012-2016.

  16. Lightweighting Impacts on Fuel Economy, Cost, and Component Losses

    Energy Technology Data Exchange (ETDEWEB)

    Brooker, A. D.; Ward, J.; Wang, L.

    2013-01-01

    The Future Automotive Systems Technology Simulator (FASTSim) is the U.S. Department of Energy's high-level vehicle powertrain model developed at the National Renewable Energy Laboratory. It uses a time versus speed drive cycle to estimate the powertrain forces required to meet the cycle. It simulates the major vehicle powertrain components and their losses. It includes a cost model based on component sizing and fuel prices. FASTSim simulated different levels of lightweighting for four different powertrains: a conventional gasoline engine vehicle, a hybrid electric vehicle (HEV), a plug-in hybrid electric vehicle (PHEV), and a battery electric vehicle (EV). Weight reductions impacted the conventional vehicle's efficiency more than the HEV, PHEV and EV. Although lightweighting impacted the advanced vehicles' efficiency less, it reduced component cost and overall costs more. The PHEV and EV are less cost effective than the conventional vehicle and HEV using current battery costs. Assuming the DOE's battery cost target of $100/kWh, however, the PHEV attained similar cost and lightweighting benefits. Generally, lightweighting was cost effective when it costs less than $6/kg of mass eliminated.

  17. The Development of Fuel Cell Technology for Electric Power Generation - From Spacecraft Applications to the Hydrogen Economy

    Science.gov (United States)

    Scott, John H.

    2005-01-01

    The fuel cell uses a catalyzed reaction between a fuel and an oxidizer to directly produce electricity. Its high theoretical efficiency and low temperature operation made it a subject of much study upon its invention ca. 1900, but its relatively high life cycle costs kept it as "solution in search of a problem" for its first half century. The first problem for which fuel cells presented a cost effective solution was, starting in the 1960's that of a power source for NASA's manned spacecraft. NASA thus invested, and continues to invest, in the development of fuel cell power plants for this application. However, starting in the mid-1990's, prospective environmental regulations have driven increased governmental and industrial interest in "green power" and the "Hydrogen Economy." This has in turn stimulated greatly increased investment in fuel cell development for a variety of terrestrial applications. This investment is bringing about notable advances in fuel cell technology, but these advances are often in directions quite different from those needed for NASA spacecraft applications. This environment thus presents both opportunities and challenges for NASA's manned space program.

  18. Fuel economy improvement based on a many-gear shifting strategy

    Energy Technology Data Exchange (ETDEWEB)

    Mashadi, B. [School of Automotive Engineering, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of); Baghaei Lakeh, R. [Department of Mechanical Engineering, Southern Illinois University, Edwardsville (United States)

    2012-07-01

    Considering the engine operating condition in terms of engine load and engine speed, a fuzzy decision making system has been developed. The objective was to controlling the engine operating point in the engine torque-rpm map, in order to enhance fuel economy. The main idea stems from the approach of tracking the defined target curve in the engine map similar to the CVT control criteria. To provide resemblance between a traditional geared transmission and a CVT, a many-gear transmission concept was introduced. A Fuzzy control was utilized by defining proper membership functions for the inputs and output. The efficient fuel consumption curve in the engine map was taken as the target of controller. The effect of engine output power on fuel consumption has also been taken into consideration. Making use of ADVISOR software, vehicle simulations was performed for the many-gear base case and a very good consistency was found with the CVT case. As a result the fuel consumption was found to become considerably less than existing values. The developed strategy was then applied to other cases including conventional manual and automatic transmissions and improvements in the fuel economy was observed.

  19. Experimental study on fuel economies and emissions of direct-injection premixed combustion engine fueled with gasoline/diesel blends

    International Nuclear Information System (INIS)

    Du, Jiakun; Sun, Wanchen; Guo, Liang; Xiao, Senlin; Tan, Manzhi; Li, Guoliang; Fan, Luyan

    2015-01-01

    Highlights: • A compound combustion concept was proposed and investigated. • Premixed combustion near the top dead center was investigated using blended fuels. • Increasing gasoline blend ratio was found to enhance the mixture preparation. • Too much addition of gasoline decreases indicated thermal efficiency. • Gasoline/diesel blends may be a promising alternative for premixed combustion. - Abstract: The effects of gasoline/diesel blended fuel composed of diesel fuel with gasoline as additives in volume basis, on combustion, fuel economies and exhaust emissions were experimentally investigated. Tests were carried out based on a turbocharged Common-rail Direct Injection engine at a constant engine speed of 1800 r/min and different loads of 3.2 bar, 5.1 bar Indicated Mean Effective Pressure. Additionally, the effect of combustion phasing and Exhaust Gas Recirculation were evaluated experimentally for various fuels. The results indicated that with the fraction of gasoline increasing in blends, the ignition delay was prolonged and the combustion phasing was retarded with the common injection timing. This led to a significant increase of premixed burning phase, which was in favor of smoke reduction; although, too much gasoline might be adverse to fuel consumption. An optimum combustion phasing was identified, leading to a higher thermal efficiency and better premixed combustion with blended fuels. A combined application of Exhaust Gas Recirculation and blended fuel with a high gasoline fraction was confirmed effective in reducing the oxides of nitrogen and smoke emissions simultaneously at the optimum combustion phasing without giving significant penalty of fuel consumption. A compound combustion mode with its emission lower than the conventional Compression Ignition engines, and efficiency higher than the typical Spark Ignition engines, could be achieved with a cooperative control of Exhaust Gas Recirculation and combustion phasing of the gasoline

  20. US Department of Energy Hybrid Electric Vehicle Battery and Fuel Economy Testing

    Science.gov (United States)

    Karner, Donald; Francfort, James

    The advanced vehicle testing activity (AVTA), part of the US Department of Energy's FreedomCAR and Vehicle Technologies Program, has conducted testing of advanced technology vehicles since August 1995 in support of the AVTA goal to provide benchmark data for technology modelling, and research and development programs. The AVTA has tested over 200 advanced technology vehicles including full-size electric vehicles, urban electric vehicles, neighborhood electric vehicles, and internal combustion engine vehicles powered by hydrogen. Currently, the AVTA is conducting a significant evaluation of hybrid electric vehicles (HEVs) produced by major automotive manufacturers. The results are posted on the AVTA web page maintained by the Idaho National Laboratory. Through the course of this testing, the fuel economy of HEV fleets has been monitored and analyzed to determine the 'real world' performance of their hybrid energy systems, particularly the battery. The initial fuel economy of these vehicles has typically been less than that determined by the manufacturer and also varies significantly with environmental conditions. Nevertheless, the fuel economy and, therefore, battery performance, has remained stable over the life of a given vehicle (160 000 miles).

  1. Structure and impacts of fuel economy standards for passenger cars in China

    International Nuclear Information System (INIS)

    Wagner, David Vance; An Feng; Wang Cheng

    2009-01-01

    By the end of 2006, there were about 24 million total passenger cars on the roads in China, nearly three times as many as in 2001. To slow the increase in energy consumption by these cars, China began implementing passenger car fuel economy standards in two phases beginning in 2005. Phase 1 fuel consumption limits resulted in a sales-weighted new passenger car average fuel consumption decrease of about 11%, from just over 9 l/100 km to approximately 8 l/100 km, from 2002 to 2006. However, we project that upon completion of Phase 2 limits in 2009, the average fuel consumption of new passenger cars in China may drop only by an additional 1%, to approximately 7.9 l/100 km. This is due to the fact that a majority of cars sold in 2006 already meets the stricter second phase fuel consumption limits. Simultaneously, other trends in the Chinese vehicle market, including increases in average curb weight and increases in standards-exempt imported vehicles, threaten to offset the efficiency gains achieved from 2002 to 2006. It is clear that additional efforts and policies beyond Phase 2 fuel consumption limits are required to slow and, ultimately, reverse the trend of rapidly rising energy consumption and greenhouse gases from China's transportation sector.

  2. Development of the fuel and energy complex within the less demanding variant of Czechoslovak economy till 2000

    International Nuclear Information System (INIS)

    Kopac, P.; Blaha, J.; Maly, M.

    1989-01-01

    The character of the fuel and energy complex which has to serve national economy, requires that it be developed according to the needs and possibilities of national economy. A projection of social and economic development of Czechoslovakia till 2000 was set up by the Central Institute of National Economy Research and it was used as the basis of a scenario of the development of the fuel and energy complex. The results are given of modeling the development of the complex. (author). 6 tabs., 3 refs

  3. 40 CFR 600.206-08 - Calculation and use of FTP-based and HFET-based fuel economy values for vehicle configurations.

    Science.gov (United States)

    2010-07-01

    ... EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-Procedures... economy value exists for an electric vehicle configuration, all values for that vehicle configuration are... HFET-based fuel economy values for vehicle configurations. 600.206-08 Section 600.206-08 Protection of...

  4. The National Center For Hydrogen And Fuel Cells. Jump-starting the hydrogen economy through research

    International Nuclear Information System (INIS)

    Stefanescu, Ioan; Varlam, Mihai; Carcadea, Elena

    2010-01-01

    Full text: The research, design and implementation of hydrogen-based economy must consider each of the segments of the hydrogen energy system - production, supply, storage, conversion. The National Center for Hydrogen and Fuel Cells has the experience, expertise, facilities and instrumentation necessary to have a key role in developing any aspect of hydrogen-based economy, aiming to integrate technologies for producing and using hydrogen as an 'energy vector'. This paper presents a simulation of the applied 'learning curve' concept, NCHFC being the key element of R and D in the field in comparing the costs involved. It also presents the short and medium term research program of NCHFC, the main research and development directions being specified. (authors)

  5. China's fuel economy standards for passenger vehicles. Rationale, policy process, and impacts

    International Nuclear Information System (INIS)

    Oliver, Hongyan H.; Gallagher, Kelly Sims; Tian, Donglian; Zhang, Jinhua

    2009-01-01

    China issued its first Fuel Economy Standards (FES) for light-duty passenger vehicles (LDPV) in September 2004, and the first and second phases of the FES took effective in July 2005 and January 2008, respectively. The stringency of the Chinese FES ranks third globally, following the Japanese and European standards. In this paper, we first review the policy-making background, including the motivations, key players, and the process; and then explain the content and the features of the FES and why there was no compliance flexibility built into it. Next, we assess the various aspects of the standard's impact, including fuel economy improvement, technology changes, shift of market composition, and overall fuel savings. Lastly, we comment on the prospect of tightening the existing FES and summarize the complementary policies that have been adopted or may be considered by the Chinese government for further promoting efficient vehicles and reducing transport energy consumption. The Chinese experience is highly relevant for countries that are also experiencing or anticipating rapid growth in personal vehicles, those wishing to moderate an increase in oil demand, or those desirous of vehicle technology upgrades. (author)

  6. The Impact of Analog and Bang-Bang Steering Gear Control on Ship's Fuel Economy

    DEFF Research Database (Denmark)

    Nørtoft Thomsen, J. C.; Blanke, Mogens; Reid, R. E.

    1982-01-01

    it is found to be at least equally important regarding steering performance and fuel economy. The paper presents a comprehensive survey of steering gear principles commonly used, including relevant details of three analog steering gear servo principles, which have outperformed conventional designs. Control......The latest years have shown considerable efforts towards improving steering generated propulsion losses of ships by the introduction of various sophisticated control algorithms in the autopilots. However, little previous attention has been given to the steering gear control loop, although...

  7. Particle swarm optimization of driving torque demand decision based on fuel economy for plug-in hybrid electric vehicle

    International Nuclear Information System (INIS)

    Shen, Peihong; Zhao, Zhiguo; Zhan, Xiaowen; Li, Jingwei

    2017-01-01

    In this paper, an energy management strategy based on logic threshold is proposed for a plug-in hybrid electric vehicle. The plug-in hybrid electric vehicle powertrain model is established using MATLAB/Simulink based on experimental tests of the power components, which is validated by the comparison with the verified simulation model which is built in the AVL Cruise. The influence of the driving torque demand decision on the fuel economy of plug-in hybrid electric vehicle is studied using a simulation. The optimization method for the driving torque demand decision, which refers to the relationship between the accelerator pedal opening and driving torque demand, from the perspective of fuel economy is formulated. The dynamically changing inertia weight particle swarm optimization is used to optimize the decision parameters. The simulation results show that the optimized driving torque demand decision can improve the PHEV fuel economy by 15.8% and 14.5% in the fuel economy test driving cycle of new European driving cycle and worldwide harmonized light vehicles test respectively, using the same rule-based energy management strategy. The proposed optimization method provides a theoretical guide for calibrating the parameters of driving torque demand decision to improve the fuel economy of the real plug-in hybrid electric vehicle. - Highlights: • The influence of the driving torque demand decision on the fuel economy is studied. • The optimization method for the driving torque demand decision is formulated. • An improved particle swarm optimization is utilized to optimize the parameters. • Fuel economy is improved by using the optimized driving torque demand decision.

  8. Substantial improvements of fuel economy. Potentials of electric and hybrid electric vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Joergensen, K [Technical Univ. of Denmark (Denmark); Nielsen, L H [Forskningscenter Risoe (Denmark)

    1996-12-01

    This paper evaluates the scope for improvement of the energy and environmental impacts of road traffic by means of electrical and hybrid electric propulsion. These technologies promise considerable improvements of the fuel economy of vehicles compared to the present vehicle types as well as beneficial effects for the energy and traffic system. The paper - based on work carried out in the project `Transportation fuel based on renewable energy`, funded by the National Energy Agency of Denmark and carried out by Department of Buildings and Energy, Technical University of Denmark and System Analysis Department, Risoe National Laboratory - assesses the potentials for reduction of the primary energy consumption and emissions, and points to the necessary technical development to reap these benefits. A case study concerning passenger cars is analysed by means of computer simulations, comparing electric and hybrid electric passenger car to an equivalent reference vehicle (a conventional gasoline passenger car). (au) 10 refs.

  9. Substitutability of Electricity and Renewable Materials for Fossil Fuels in a Post-Carbon Economy

    Directory of Open Access Journals (Sweden)

    Antonio García-Olivares

    2015-11-01

    Full Text Available A feasible way to avoid the risk of energy decline and combat climate change is to build a 100% renewable global energy mix. However, a globally electrified economy cannot grow much above 12 electric terawatts without putting pressure on the limits of finite mineral reserves. Here we analyze whether 12 TW of electricity and 1 TW of biomass (final power will be able to fuel a future post-carbon economy that can provide similar services to those of a contemporary economy. Contrarily to some pessimistic expectations, this analysis shows that the principle economic processes can be replaced with sustainable alternatives based on electricity, charcoal, biogas and hydrogen. Furthermore, those services that cannot be replaced are not as crucial so as to cause a return to a pre-industrial society. Even so, land transport and aviation are at the limit of what is sustainable, outdoor work should be reorganized, metal primary production should be based on hydrogen reduction when possible, mineral production should be increasingly based on recycling, the petrochemical industry should shrink to a size of 40%–43% of the 2012 petrochemical sector, i.e., a size similar to that the sector had in 1985–1986, and agriculture may require organic farming methods to be sustainable.

  10. Nuclear fuel cycle facilities in the world (excluding the centrally planned economies)

    International Nuclear Information System (INIS)

    1979-01-01

    Information on the existing, under construction and planned fuel cycle facilities in the various countries is presented. Some thirty countries have activities related to different nuclear fuel cycle steps and the information covers the capacity, status, location, and the names of owners of the facilities

  11. Buses retrofitting with diesel particle filters: Real-world fuel economy and roadworthiness test considerations.

    Science.gov (United States)

    Fleischman, Rafael; Amiel, Ran; Czerwinski, Jan; Mayer, Andreas; Tartakovsky, Leonid

    2018-05-01

    Retrofitting older vehicles with diesel particulate filter (DPF) is a cost-effective measure to quickly and efficiently reduce particulate matter emissions. This study experimentally analyzes real-world performance of buses retrofitted with CRT DPFs. 18 in-use Euro III technology urban and intercity buses were investigated for a period of 12months. The influence of the DPF and of the vehicle natural aging on buses fuel economy are analyzed and discussed. While the effect of natural deterioration is about 1.2%-1.3%, DPF contribution to fuel economy penalty is found to be 0.6% to 1.8%, depending on the bus type. DPF filtration efficiency is analyzed throughout the study and found to be in average 96% in the size range of 23-560nm. Four different load and non-load engine operating modes are investigated on their appropriateness for roadworthiness tests. High idle is found to be the most suitable regime for PN diagnostics considering particle number filtration efficiency. Copyright © 2017. Published by Elsevier B.V.

  12. Hydraulic Hybrid and Conventional Parcel Delivery Vehicles' Measured Laboratory Fuel Economy on Targeted Drive Cycles

    Energy Technology Data Exchange (ETDEWEB)

    Lammert, M. P.; Burton, J.; Sindler, P.; Duran, A.

    2014-10-01

    This research project compares laboratory-measured fuel economy of a medium-duty diesel powered hydraulic hybrid vehicle drivetrain to both a conventional diesel drivetrain and a conventional gasoline drivetrain in a typical commercial parcel delivery application. Vehicles in this study included a model year 2012 Freightliner P100H hybrid compared to a 2012 conventional gasoline P100 and a 2012 conventional diesel parcel delivery van of similar specifications. Drive cycle analysis of 484 days of hybrid parcel delivery van commercial operation from multiple vehicles was used to select three standard laboratory drive cycles as well as to create a custom representative cycle. These four cycles encompass and bracket the range of real world in-use data observed in Baltimore United Parcel Service operations. The NY Composite cycle, the City Suburban Heavy Vehicle Cycle cycle, and the California Air Resources Board Heavy Heavy-Duty Diesel Truck (HHDDT) cycle as well as a custom Baltimore parcel delivery cycle were tested at the National Renewable Energy Laboratory's Renewable Fuels and Lubricants Laboratory. Fuel consumption was measured and analyzed for all three vehicles. Vehicle laboratory results are compared on the basis of fuel economy. The hydraulic hybrid parcel delivery van demonstrated 19%-52% better fuel economy than the conventional diesel parcel delivery van and 30%-56% better fuel economy than the conventional gasoline parcel delivery van on cycles other than the highway-oriented HHDDT cycle.

  13. The Fuel Economy of Hybrid Buses: The Role of Ancillaries in Real Urban Driving

    Directory of Open Access Journals (Sweden)

    Francesco Bottiglione

    2014-07-01

    Full Text Available In the present context of the global economic crisis and environmental emergency, transport science is asked to find innovative solutions to turn traditional vehicles into fuel-saving and eco-friendly devices. In the last few years, hybrid vehicles have been shown to have potential benefits in this sense. In this paper, the fuel economy of series hybrid-electric and hybrid-mechanical buses is simulated in two real driving situations: cold and hot weather driving in the city of Taranto, in Southern Italy. The numerical analysis is carried out by an inverse dynamic approach, where the bus speed is given as a velocity pattern measured in the field tests performed on one of the city bus routes. The city of Taranto drive schedule is simulated in a typical tempered climate condition and with a hot temperature, when the air conditioning system must be switched on for passenger comfort. The fuel consumptions of hybrid-electric and hybrid-mechanical buses are compared to each other and with a traditional bus powered by a diesel engine. It is shown that the series hybrid-electric vehicle outperforms both the traditional and the mechanical hybrid vehicles in the cold weather driving simulation, reducing the fuel consumption by about 35% with respect to the traditional diesel bus. However, it is also shown that the performance of the hybrid-electric bus gets dramatically worse when the air-cooling system is continuously turned on. In this situation, the fuel consumption of the three different technologies for city buses under investigation is comparable.

  14. Reduction in global warming due to fuel economy improvements and emissions control of criteria pollutants: New US light-duty vehicles (1968--1991)

    International Nuclear Information System (INIS)

    Pitstick, M.E.; Santini, D.J.; Chauhan, H.

    1992-01-01

    This paper explores the impact of US emission controls and fuel economy improvements on the global warming potential (GWP) of new light-duty vehicles. Fuel economy improvements have reduced the GWP of both passenger cars and light-duty trucks by lowering the per mile emissions of carbon dioxide (CO 2 ). Further GWP reductions have been achieved by emission standards for criteria pollutants: carbon monoxide (CO), hydrocarbons (HC), and nitrogen oxides (NO x ). The GWP of a criteria pollutant was calculated by multiplying the emission rate by a relative global warming factor to obtain a CO 2 equivalent emission rate. Both CO 2 and criteria pollutant emission rates per vehicle have decreased substantially for new light-duty vehicles over the period from 1968 to 1991. Over that period, the GWP from CO 2 was reduced by almost 50% in new vehicles by improving fuel economy. In that same time period, the GWP from criteria pollutants from new vehicles was reduced with emission controls by from 80% to 90% depending on the global warming time frame of interest. Consequently, total reductions in the GWP of new passenger cars and light-duty trucks have been on the order of 55 to 75 percent compared to precontrol (before 1968) new vehicles. However, the reduction in GWP caused by emission control of criteria pollutants has been larger than the reduction caused by improved fuel economy (i.e., reduced CO 2 ). The contribution of criteria pollutants to the GWP of precontrol new vehicles was substantial, but their contribution has been reduced significantly due to US emission controls. As a result, the contribution of criteria pollutants to global warming is now much less than the contribution of CO 2 from fuel consumption

  15. Reduction in global warming due to fuel economy improvements and emissions control of criteria pollutants: New US light-duty vehicles (1968--1991)

    Energy Technology Data Exchange (ETDEWEB)

    Pitstick, M.E.; Santini, D.J. [Argonne National Lab., IL (United States); Chauhan, H. [Delaware Univ., Newark, DE (United States). Dept. of Civil Engineering

    1992-08-01

    This paper explores the impact of US emission controls and fuel economy improvements on the global warming potential (GWP) of new light-duty vehicles. Fuel economy improvements have reduced the GWP of both passenger cars and light-duty trucks by lowering the per mile emissions of carbon dioxide (CO{sub 2}). Further GWP reductions have been achieved by emission standards for criteria pollutants: carbon monoxide (CO), hydrocarbons (HC), and nitrogen oxides (NO{sub x}). The GWP of a criteria pollutant was calculated by multiplying the emission rate by a relative global warming factor to obtain a CO{sub 2} equivalent emission rate. Both CO{sub 2} and criteria pollutant emission rates per vehicle have decreased substantially for new light-duty vehicles over the period from 1968 to 1991. Over that period, the GWP from CO{sub 2} was reduced by almost 50% in new vehicles by improving fuel economy. In that same time period, the GWP from criteria pollutants from new vehicles was reduced with emission controls by from 80% to 90% depending on the global warming time frame of interest. Consequently, total reductions in the GWP of new passenger cars and light-duty trucks have been on the order of 55 to 75 percent compared to precontrol (before 1968) new vehicles. However, the reduction in GWP caused by emission control of criteria pollutants has been larger than the reduction caused by improved fuel economy (i.e., reduced CO{sub 2}). The contribution of criteria pollutants to the GWP of precontrol new vehicles was substantial, but their contribution has been reduced significantly due to US emission controls. As a result, the contribution of criteria pollutants to global warming is now much less than the contribution of CO{sub 2} from fuel consumption.

  16. Reduction in global warming due to fuel economy improvements and emissions control of criteria pollutants: New US light-duty vehicles (1968--1991)

    Energy Technology Data Exchange (ETDEWEB)

    Pitstick, M.E.; Santini, D.J. (Argonne National Lab., IL (United States)); Chauhan, H. (Delaware Univ., Newark, DE (United States). Dept. of Civil Engineering)

    1992-01-01

    This paper explores the impact of US emission controls and fuel economy improvements on the global warming potential (GWP) of new light-duty vehicles. Fuel economy improvements have reduced the GWP of both passenger cars and light-duty trucks by lowering the per mile emissions of carbon dioxide (CO{sub 2}). Further GWP reductions have been achieved by emission standards for criteria pollutants: carbon monoxide (CO), hydrocarbons (HC), and nitrogen oxides (NO{sub x}). The GWP of a criteria pollutant was calculated by multiplying the emission rate by a relative global warming factor to obtain a CO{sub 2} equivalent emission rate. Both CO{sub 2} and criteria pollutant emission rates per vehicle have decreased substantially for new light-duty vehicles over the period from 1968 to 1991. Over that period, the GWP from CO{sub 2} was reduced by almost 50% in new vehicles by improving fuel economy. In that same time period, the GWP from criteria pollutants from new vehicles was reduced with emission controls by from 80% to 90% depending on the global warming time frame of interest. Consequently, total reductions in the GWP of new passenger cars and light-duty trucks have been on the order of 55 to 75 percent compared to precontrol (before 1968) new vehicles. However, the reduction in GWP caused by emission control of criteria pollutants has been larger than the reduction caused by improved fuel economy (i.e., reduced CO{sub 2}). The contribution of criteria pollutants to the GWP of precontrol new vehicles was substantial, but their contribution has been reduced significantly due to US emission controls. As a result, the contribution of criteria pollutants to global warming is now much less than the contribution of CO{sub 2} from fuel consumption.

  17. Voluntary Truck and Bus Fuel-Economy-Program marketing plan. Final technical report, September 29, 1980-January 29, 1982

    Energy Technology Data Exchange (ETDEWEB)

    None

    1982-01-01

    The aim of the program is to improve the utilization of fuel by commercial trucks and buses by updating and implementing specific approaches for educating and monitoring the trucking industry on methods and means of conserving fuels. The following outlines the marketing plan projects: increase use of program logo by voluntary program members and others; solicit trade publication membership and support; brief Congressional delegations on fuel conservation efforts; increase voluntary program presence before trade groups; increase voluntary program presence at truck and trade shows; create a voluntary program display for use at trade shows and in other areas; review voluntary program graphics; increase voluntary program membership; and produce placemats carrying fuel conservation messages; produce a special edition of Fuel Economy News, emphasizing the driver's involvement in fuel conservation; produce posters carrying voluntary program fuel conservation message. Project objectives, activities, and results for each project are summarized.

  18. About economy of fuel and energy resources in the hot water supply system

    Science.gov (United States)

    Rotov, P. V.; Sivukhin, A. A.; Zhukov, D. A.; Zhukova, A. V.

    2017-11-01

    The assessment of the power efficiency realized in the current of heat supply system of technology of regulation of loading of the hot water supply system, considering unevenness consumption of hot water is executed. For the purpose of definition the applicability boundary of realized technology comparative analysis of indicators of the effectiveness of its work within the possible range of the parameters of regulations. Developed a software application “The calculation of the total economy of fuel and energy resources in the hot water supply system when you change of the parameters of regulations”, which allows on the basis of multivariate calculations analyses of their results, to choose the optimum mode of operation heat supply system and to assess the effectiveness of load regulation in the hot water supply system.

  19. Engineering-economic analyses of automotive fuel economy potential in the United States

    Energy Technology Data Exchange (ETDEWEB)

    Greene, D.L.; DeCicco, J.

    2000-02-01

    Over the past 25 years more than 20 major studies have examined the technological potential to improve the fuel economy of passenger cars and light trucks in the US. The majority has used technology/cost analysis, a combination of analytical methods from the disciplines of economics and automotive engineering. In this paper the authors describe the key elements of this methodology, discuss critical issues responsible for the often widely divergent estimates produced by different studies, review the history of its use, and present results from six recent assessments. Whereas early studies tended to confine their scope to the potential of proven technology over a 10-year time period, more recent studies have focused on advanced technologies, raising questions about how best to include the likelihood of technological change. The paper concludes with recommendations for further research.

  20. A Model Predictive Control Approach for Fuel Economy Improvement of a Series Hydraulic Hybrid Vehicle

    Directory of Open Access Journals (Sweden)

    Tri-Vien Vu

    2014-10-01

    Full Text Available This study applied a model predictive control (MPC framework to solve the cruising control problem of a series hydraulic hybrid vehicle (SHHV. The controller not only regulates vehicle velocity, but also engine torque, engine speed, and accumulator pressure to their corresponding reference values. At each time step, a quadratic programming problem is solved within a predictive horizon to obtain the optimal control inputs. The objective is to minimize the output error. This approach ensures that the components operate at high efficiency thereby improving the total efficiency of the system. The proposed SHHV control system was evaluated under urban and highway driving conditions. By handling constraints and input-output interactions, the MPC-based control system ensures that the system operates safely and efficiently. The fuel economy of the proposed control scheme shows a noticeable improvement in comparison with the PID-based system, in which three Proportional-Integral-Derivative (PID controllers are used for cruising control.

  1. Improving of diesel combustion-pollution-fuel economy and performance by gasoline fumigation

    International Nuclear Information System (INIS)

    Şahin, Zehra; Durgun, Orhan

    2013-01-01

    Highlights: • The effects of gasoline fumigation on the engine performance and NO x emission were investigated in Ford XLD 418 T automotive diesel engine. • Gasoline at approximately (2, 4, 6, 8 10, and 12)% (by vol.) ratios was injected into intake air by a carburetor. • GF enhances effective power and reduces brake specific fuel consumption, cost, and NO x emission. - Abstract: One of the most important objectives of the studies worldwide is to improve combustion of diesel engine to meet growing energy needs and to reduce increasing environmental pollution. To accomplish this goal, especially to reduce pollutant emissions, researchers have focused their interest on the field of alternative fuels and alternative solutions. Gasoline fumigation (GF) is one of these alternative solutions, by which diesel combustion, fuel economy, and engine performance are improved, and environmental pollution is decreased. In the fumigation method, gasoline is injected into intake air, either by a carburetor, which main nozzle section is adjustable or by a simple injection system. In the present experimental study, a simple carburetor was used, and the effects of gasoline fumigation at (2, 4, 6, 8, 10, 12)% (by vol.) gasoline ratios on the combustion, NO x emission, fuel economy, and engine performance sophisticatedly investigated for a fully instrumented, four-cylinder, water-cooled indirect injection (IDI), Ford XLD 418 T automotive diesel engine. Tests were conducted for each of the above gasoline fumigation ratios at three different speeds and for (1/1, 3/4, and 1/2) fuel delivery ratios (FDRs). GF test results showed that NO x emission is lower than that of neat diesel fuel (NDF). NO x emission decreases approximately 4.20%, 2.50%, and 9.65% for (1/1, 3/4, and 1/2) FDRs, respectively. Effective power increases approximately 2.38% for 1/1 FDR. At (2500 and 3000) rpms, effective power decreases at low gasoline ratios, but it increases at high gasoline ratios for 3/4 and 1

  2. Design incentives to increase vehicle size created from the U.S. footprint-based fuel economy standards

    International Nuclear Information System (INIS)

    Whitefoot, Kate S.; Skerlos, Steven J.

    2012-01-01

    The recently amended U.S. Corporate Average Fuel Economy (CAFE) standards determine fuel-economy targets based on the footprint (wheelbase by track width) of vehicles such that larger vehicles have lower fuel-economy targets. This paper considers whether these standards create an incentive for firms to increase vehicle size by presenting an oligopolistic-equilibrium model in which automotive firms can modify vehicle dimensions, implement fuel-saving technology features, and trade off acceleration performance and fuel economy. Wide ranges of scenarios for consumer preferences are considered. Results suggest that the footprint-based CAFE standards create an incentive to increase vehicle size except when consumer preference for vehicle size is near its lower bound and preference for acceleration is near its upper bound. In all other simulations, the sales-weighted average vehicle size increases by 2–32%, undermining gains in fuel economy by 1–4 mpg (0.6–1.7 km/L). Carbon-dioxide emissions from these vehicles are 5–15% higher as a result (4.69×10 11 –5.17×10 11 kg for one year of produced vehicles compared to 4.47×10 11 kg with no size changes), which is equivalent to adding 3–10 coal-fired power plants to the electricity grid each year. Furthermore, results suggest that the incentive is larger for light trucks than for passenger cars, which could increase traffic safety risks. - Highlights: ► New U.S. fuel-economy standards may create an incentive to increase vehicle size. ► We model firms as choosing vehicle designs and prices in oligopolistic equilibrium. ► Vehicle size increases 2–32% for 20 out of 21 scenarios of consumer preferences. ► Increases in size reduce fuel economy gains from 5–13%, resulting in 5–15% higher CO 2 emissions. ► Incentive is larger for trucks than cars, which may increase traffic safety risks.

  3. Ethanol and air quality: influence of fuel ethanol content on emissions and fuel economy of flexible fuel vehicles.

    Science.gov (United States)

    Hubbard, Carolyn P; Anderson, James E; Wallington, Timothy J

    2014-01-01

    Engine-out and tailpipe emissions of NOx, CO, nonmethane hydrocarbons (NMHC), nonmethane organic gases (NMOG), total hydrocarbons (THC), methane, ethene, acetaldehyde, formaldehyde, ethanol, N2O, and NH3 from a 2006 model year Mercury Grand Marquis flexible fuel vehicle (FFV) operating on E0, E10, E20, E30, E40, E55, and E80 on a chassis dynamometer are reported. With increasing ethanol content in the fuel, the tailpipe emissions of ethanol, acetaldehyde, formaldehyde, methane, and ammonia increased; NOx and NMHC decreased; while CO, ethene, and N2O emissions were not discernibly affected. NMOG and THC emissions displayed a pronounced minimum with midlevel (E20-E40) ethanol blends; 25-35% lower than for E0 or E80. Emissions of NOx decreased by approximately 50% as the ethanol content increased from E0 to E30-E40, with no further decrease seen with E55 or E80. We demonstrate that emission trends from FFVs are explained by fuel chemistry and engine calibration effects. Fuel chemistry effects are fundamental in nature; the same trend of increased ethanol, acetaldehyde, formaldehyde, and CH4 emissions and decreased NMHC and benzene emissions are expected for all FFVs. Engine calibration effects are manufacturer and model specific; emission trends for NOx, THC, and NMOG will not be the same for all FFVs. Implications for air quality are discussed.

  4. Consumer Views: Fuel Economy, Plug-in Electric Vehicle Battery Range, and Willingness to Pay for Vehicle Technology

    Energy Technology Data Exchange (ETDEWEB)

    Singer, Mark [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2017-05-11

    This presentation includes data captured by the National Renewable Energy Laboratory (NREL) to support the U.S. Department of Energy's Vehicle Technologies Office (VTO) research efforts. The data capture consumer views on fuel economy, plug-in electric vehicle battery range, and willingness to pay for advanced vehicle technologies.

  5. Running for exercise mitigates age-related deterioration of walking economy.

    Directory of Open Access Journals (Sweden)

    Justus D Ortega

    Full Text Available Impaired walking performance is a key predictor of morbidity among older adults. A distinctive characteristic of impaired walking performance among older adults is a greater metabolic cost (worse economy compared to young adults. However, older adults who consistently run have been shown to retain a similar running economy as young runners. Unfortunately, those running studies did not measure the metabolic cost of walking. Thus, it is unclear if running exercise can prevent the deterioration of walking economy.To determine if and how regular walking vs. running exercise affects the economy of locomotion in older adults.15 older adults (69 ± 3 years who walk ≥ 30 min, 3x/week for exercise, "walkers" and 15 older adults (69 ± 5 years who run ≥ 30 min, 3x/week, "runners" walked on a force-instrumented treadmill at three speeds (0.75, 1.25, and 1.75 m/s. We determined walking economy using expired gas analysis and walking mechanics via ground reaction forces during the last 2 minutes of each 5 minute trial. We compared walking economy between the two groups and to non-aerobically trained young and older adults from a prior study.Older runners had a 7-10% better walking economy than older walkers over the range of speeds tested (p = .016 and had walking economy similar to young sedentary adults over a similar range of speeds (p =  .237. We found no substantial biomechanical differences between older walkers and runners. In contrast to older runners, older walkers had similar walking economy as older sedentary adults (p =  .461 and ∼ 26% worse walking economy than young adults (p<.0001.Running mitigates the age-related deterioration of walking economy whereas walking for exercise appears to have minimal effect on the age-related deterioration in walking economy.

  6. Law proposition relative to the ecology transformation of the economy

    International Nuclear Information System (INIS)

    Rugy, F. de; Billard, M.; Cochet, Y.; Mamere, N.

    2009-04-01

    This law proposition presents some fiscal and legal measures aiming to prepare the necessary evolution of the ecological transformation of the economy. The presented articles aim to define a legislative and fiscal framework in favor of a deep change of the production and consumption modes. Four main domains are discussed: the climate-energy contribution, the evolution of the transportation sector, the enhancement of the energy performance of the buildings, the development of the renewable energies and the reconversion of the automobile sector. (A.L.B.)

  7. Modeling and control of a hybrid-electric vehicle for drivability and fuel economy improvements

    Science.gov (United States)

    Koprubasi, Kerem

    The gradual decline of oil reserves and the increasing demand for energy over the past decades has resulted in automotive manufacturers seeking alternative solutions to reduce the dependency on fossil-based fuels for transportation. A viable technology that enables significant improvements in the overall tank-to-wheel vehicle energy conversion efficiencies is the hybridization of electrical and conventional drive systems. Sophisticated hybrid powertrain configurations require careful coordination of the actuators and the onboard energy sources for optimum use of the energy saving benefits. The term optimality is often associated with fuel economy, although other measures such as drivability and exhaust emissions are also equally important. This dissertation focuses on the design of hybrid-electric vehicle (HEV) control strategies that aim to minimize fuel consumption while maintaining good vehicle drivability. In order to facilitate the design of controllers based on mathematical models of the HEV system, a dynamic model that is capable of predicting longitudinal vehicle responses in the low-to-mid frequency region (up to 10 Hz) is developed for a parallel HEV configuration. The model is validated using experimental data from various driving modes including electric only, engine only and hybrid. The high fidelity of the model makes it possible to accurately identify critical drivability issues such as time lags, shunt, shuffle, torque holes and hesitation. Using the information derived from the vehicle model, an energy management strategy is developed and implemented on a test vehicle. The resulting control strategy has a hybrid structure in the sense that the main mode of operation (the hybrid mode) is occasionally interrupted by event-based rules to enable the use of the engine start-stop function. The changes in the driveline dynamics during this transition further contribute to the hybrid nature of the system. To address the unique characteristics of the HEV

  8. Sustainable and safe energy supply with seawater uranium fueled HTGR and its economy

    International Nuclear Information System (INIS)

    Fukaya, Y.; Goto, M.

    2017-01-01

    Highlights: • We discussed uranium resources with an energy security perspective. • We concluded seawater uranium is preferable for sustainability and energy security. • We evaluated electricity generation cost of seawater uranium fueled HTGR. • We concluded electricity generation with seawater uranium is reasonable. - Abstract: Sustainable and safe energy supply with High Temperature Gas-cooled Reactor (HTGR) fueled by uranium from seawater have been investigated and discussed. From the view point of safety feature of self-regulation with thermal reactor of HTGR, the uranium resources should be inexhaustible. The seawater uranium is expected to be alternative resources to conventional resources because it exists so much in seawater as a solute. It is said that 4.5 billion tons of uranium is dissolved in the seawater, which corresponds to a consumption of approximately 72 thousand years. Moreover, a thousand times of the amount of 4.5 trillion tU of uranium, which corresponds to the consumption of 72 million years, also is included in the rock on the surface of the sea floor, and that is also recoverable as seawater uranium because uranium in seawater is in an equilibrium state with that. In other words, the uranium from seawater is almost inexhaustible natural resource. However, the recovery cost with current technology is still expensive compared with that of conventional uranium. Then, we assessed the effect of increase in uranium purchase cost on the entire electricity generation cost. In this study, the economy of electricity generation of cost of a commercial HTGR was evaluated with conventional uranium and seawater uranium. Compared with ordinary LWR using conventional uranium, HTGR can generate electricity cheaply because of small volume of simple direct gas turbine system compared with water and steam systems of LWR, rationalization by modularizing, and high thermal efficiency, even if fueled by seawater uranium. It is concluded that the HTGR

  9. Running for exercise mitigates age-related deterioration of walking economy.

    Science.gov (United States)

    Ortega, Justus D; Beck, Owen N; Roby, Jaclyn M; Turney, Aria L; Kram, Rodger

    2014-01-01

    Impaired walking performance is a key predictor of morbidity among older adults. A distinctive characteristic of impaired walking performance among older adults is a greater metabolic cost (worse economy) compared to young adults. However, older adults who consistently run have been shown to retain a similar running economy as young runners. Unfortunately, those running studies did not measure the metabolic cost of walking. Thus, it is unclear if running exercise can prevent the deterioration of walking economy. To determine if and how regular walking vs. running exercise affects the economy of locomotion in older adults. 15 older adults (69 ± 3 years) who walk ≥ 30 min, 3x/week for exercise, "walkers" and 15 older adults (69 ± 5 years) who run ≥ 30 min, 3x/week, "runners" walked on a force-instrumented treadmill at three speeds (0.75, 1.25, and 1.75 m/s). We determined walking economy using expired gas analysis and walking mechanics via ground reaction forces during the last 2 minutes of each 5 minute trial. We compared walking economy between the two groups and to non-aerobically trained young and older adults from a prior study. Older runners had a 7-10% better walking economy than older walkers over the range of speeds tested (p = .016) and had walking economy similar to young sedentary adults over a similar range of speeds (p =  .237). We found no substantial biomechanical differences between older walkers and runners. In contrast to older runners, older walkers had similar walking economy as older sedentary adults (p =  .461) and ∼ 26% worse walking economy than young adults (peconomy whereas walking for exercise appears to have minimal effect on the age-related deterioration in walking economy.

  10. The political economy of diagnosis-related groups.

    Science.gov (United States)

    Bertoli, Paola; Grembi, Veronica

    2017-10-01

    A well-established political economic literature has shown as multi-level governance affects the inefficiency of public expenditures. Yet, this expectation has not been empirically tested on health expenditures. We provide a political economy interpretation of the variation in the prices of 6 obstetric DRGs using Italy as a case study. Italy offers a unique institutional setting since its 21 regional governments can decide whether to adopt the national DRG system or to adjust/waive it. We investigate whether the composition and characteristics of regional governments do matter for the average DRG level and, if so, why. To address both questions, we first use a panel fixed effects model exploiting the results of 66 elections between 2000 and 2013 (i.e., 294 obs) to estimate the link between DRGs and the composition and characteristics of regional governments. Second, we investigate these results exploiting the implementation of a budget constraint policy through a difference-in-differences framework. The incidence of physicians in the regional government explains the variation of DRGs with low technological intensity, such as normal newborn, but not of those with high technological intensity, as severely premature newborn. We also observe a decrease in the average levels of DRGs after the budget constraint implementation, but the magnitude of this decrease depends primarily on the presence of physicians among politicians and the political alignment between the regional and the national government. To understand which kind of role the relevance of the political components plays (i.e., waste vs. better defined DRGs), we check whether any of the considered political economy variables have a positive impact on the quality of regional obstetric systems finding no effect. These results are a first evidence that a system of standardized prices, such as the DRGs, is not immune to political pressures. Copyright © 2017 Elsevier Ltd. All rights reserved.

  11. USSR Report, World Economy and International Relations, No. 12, December 1986

    National Research Council Canada - National Science Library

    1987-01-01

    This report is a Translation of the Russian-language monthly journal MIROVAYA EKONOMIKA I MEZHDUNARODNYYE OTNOSHENIYA published in Moscow by the Institute of World Economy and international Relations...

  12. JPRS Report. Soviet Union: World Economy & International Relations, No. 4, April 1989

    National Research Council Canada - National Science Library

    1989-01-01

    This report is a translation of the Russian-language monthly journal MIROVAYA EKONOMIKA I MEZHDUNARODNYYE OTNOSHENIYA published in Moscow by the Institute of World Economy and International Relations...

  13. JPRS Report. Soviet Union: World Economy & International Relations, No. 2, February 1989

    National Research Council Canada - National Science Library

    1989-01-01

    This report is a translation of the Russian-language monthly journal MIROVAYA EKONOMIKA I MEZHDUNARODNYYE OTNOSHENIYA published in Moscow by the Institute of World Economy and International Relations...

  14. Gasoline prices, gasoline consumption, and new-vehicle fuel economy: Evidence for a large sample of countries

    International Nuclear Information System (INIS)

    Burke, Paul J.; Nishitateno, Shuhei

    2013-01-01

    Countries differ considerably in terms of the price drivers pay for gasoline. This paper uses data for 132 countries for the period 1995–2008 to investigate the implications of these differences for the consumption of gasoline for road transport. To address the potential for simultaneity bias, we use both a country's oil reserves and the international crude oil price as instruments for a country's average gasoline pump price. We obtain estimates of the long-run price elasticity of gasoline demand of between − 0.2 and − 0.5. Using newly available data for a sub-sample of 43 countries, we also find that higher gasoline prices induce consumers to substitute to vehicles that are more fuel-efficient, with an estimated elasticity of + 0.2. Despite the small size of our elasticity estimates, there is considerable scope for low-price countries to achieve gasoline savings and vehicle fuel economy improvements via reducing gasoline subsidies and/or increasing gasoline taxes. - Highlights: ► We estimate the determinants of gasoline demand and new-vehicle fuel economy. ► Estimates are for a large sample of countries for the period 1995–2008. ► We instrument for gasoline prices using oil reserves and the world crude oil price. ► Gasoline demand and fuel economy are inelastic with respect to the gasoline price. ► Large energy efficiency gains are possible via higher gasoline prices

  15. A prospective analysis of Brazilian biofuel economy: Land use, infrastructure development and fuel pricing policies

    Science.gov (United States)

    Nunez Amortegui, Hector Mauricio

    Being the two largest ethanol producers in the world, transportation fuel policies in Brazil and the U.S. affect not only their domestic markets but also the global food and biofuel economy. Hence, the complex biofuel policy climate in these countries leaves the public with unclear conclusions about the prospects for supply and trade of agricultural commodities and biofuels. In this dissertation I develop a price endogenous mathematical programming model to simulate and analyze the impacts of biofuel policies in Brazil and the U.S. on land use in these countries, agricultural commodity and transportation fuel markets, trade, and global environment. The model maximizes the social surplus represented by the sum of producers' and consumers' surpluses, including selected agricultural commodity markets and fuel markets in the U.S., Brazil, Argentina, China, and the Rest-of-the-World (ROW), subject to resource limitations, material balances, technical constraints, and policy restrictions. Consumers' surplus is derived from consumption of agricultural commodities and transportation fuels by vehicles that generate vehicle-kilometers-traveled (VKT). While in the other regional components aggregate supply and demand functions are assumed for the commodities included in the analysis, the agricultural supply component is regionally disaggregated for Brazil and the U.S., and the transportation fuel sector is regionally disaggregated for Brazil. The U.S. agricultural supply component includes production of fourteen major food/feed crops, including soybeans, corn and wheat, and cellulosic biofuel feedstocks. The Brazil component includes eight major annual crops, including soybeans, corn, wheat, and rice, and sugarcane as the energy crop. A particular emphasis is given to the beef-cattle production in Brazil and the potential for livestock semi-intensification in Brazilian pasture grazing systems as a prospective pathway for releasing new croplands. In the fuel sector of both

  16. IAEA Activities in the Area of Fast Reactors and Related Fuels and Fuel Cycles

    International Nuclear Information System (INIS)

    Monti, S.; Basak, U.; Dyck, G.; Inozemtsev, V.; Toti, A.; Zeman, A.

    2013-01-01

    Summary: • The IAEA role to support fast reactors and associated fuel cycle development programmes; • Main IAEA activities on fast reactors and related fuel and fuel cycle technology; • Main IAEA deliverables on fast reactors and related fuel and fuel cycle technology

  17. Evaluating the Impact of Road Grade on Simulated Commercial Vehicle Fuel Economy Using Real-World Drive Cycles

    Energy Technology Data Exchange (ETDEWEB)

    Lopp, Sean; Wood, Eric; Duran, Adam

    2015-10-13

    Commercial vehicle fuel economy is known to vary significantly with both positive and negative road grade. Medium- and heavy-duty vehicles operating at highway speeds require incrementally larger amounts of energy to pull heavy payloads up inclines as road grade increases. Non-hybrid vehicles are then unable to recapture energy on descent and lose energy through friction braking. While the on-road effects of road grade are well understood, the majority of standard commercial vehicle drive cycles feature no climb or descent requirements. Additionally, existing literature offers a limited number of sources that attempt to estimate the on-road energy implications of road grade in the medium- and heavy-duty space. This study uses real-world commercial vehicle drive cycles from the National Renewable Energy Laboratory's Fleet DNA database to simulate the effects of road grade on fuel economy across a range of vocations, operating conditions, and locations. Drive-cycles are matched with vocation-specific vehicle models and simulated with and without grade. Fuel use due to grade is presented, and variation in fuel consumption due to drive cycle and vehicle characteristics is explored through graphical and statistical comparison. The results of this study suggest that road grade accounts for 1%-9% of fuel use in commercial vehicles on average and up to 40% on select routes.

  18. Measuring of Traction and Speed Characteristics as Well as of Fuel Economy of a Car in Road Conditions

    OpenAIRE

    Krivtsov, Sergey; Syrbakov, Andrey Pavlovich; Korchuganova, Mariya Anatolievna

    2016-01-01

    This article is devoted to the identification of traction and speed characteristics as well as of fuel economy of motor vehicles in road conditions. Among common variants of measuring of the above stated values, the preference was given to the immediate gaining of factors by means of a computer-aided measuring system. There is a theoretical justification given to the suggested approach as well as methods and results allowing to provide a practically sufficient solution accuracy of the problem.

  19. Measuring of Traction and Speed Characteristics as Well as of Fuel Economy of a Car in Road Conditions

    Science.gov (United States)

    Krivtsov, Sergey N.; Syrbakov, Andrey P.; Korchuganova, Marina A.

    2016-08-01

    This article is devoted to the identification of traction and speed characteristics as well as of fuel economy of motor vehicles in road conditions. Among common variants of measuring of the above stated values, the preference was given to the immediate gaining of factors by means of a computer-aided measuring system. There is a theoretical justification given to the suggested approach as well as methods and results allowing to provide a practically sufficient solution accuracy of the problem.

  20. Study of emissions and fuel economy for parallel hybrid versus conventional vehicles on real world and standard driving cycles

    Directory of Open Access Journals (Sweden)

    Ahmed Al-Samari

    2017-12-01

    Full Text Available Parallel hybrid electric vehicles (PHEVs increasing rapidly in the automobile markets. However, the benefits out of using this kind of vehicles are still concerned a lot of costumers. This work investigated the expected benefits (such as decreasing emissions and increasing fuel economy from using the parallel HEV in comparison to the conventional vehicle model of the real-world and standard driving cycles. The software Autonomie used in this study to simulate the parallel HEV and conventional models on these driving cycles.The results show that the fuel economy (FE can be improved significantly up to 68% on real-world driving cycle, which is represented mostly city activities. However, the FE improvement was limited (10% on the highway driving cycle, and this is expected since the using of brake system was infrequent. Moreover, the emissions from parallel HEV decreased about 40% on the real-world driving cycle, and decreased 11% on the highway driving cycle. Finally, the engine efficiency, improved about 12% on the real-world driving cycle, and about 7% on highway driving cycle. Keywords: Emissions, Hybrid electric vehicles, Fuel economy, Real-world driving cycle

  1. Problems related to fossil fuels utilization

    International Nuclear Information System (INIS)

    Rota, R.

    1999-01-01

    Fossil fuels still present the main energy source in the world since about 90% of the energy produced comes from combustion. This paper, based on the lectures given at the conference of Energy and Environment hold at the Accademia dei Lincei in 1998, presents a short review of some of the problems related to the utilization of fossil fuels, such as their availability in the medium period, the effect of pollutant dispersion in the atmosphere as well as the available technologies to deal with such problems [it

  2. Development & optimization of a rule-based energy management strategy for fuel economy improvement in hybrid electric vehicles

    Science.gov (United States)

    Asfoor, Mostafa

    The gradual decline of oil reserves and the increasing demand for energy over the past decades has resulted in automotive manufacturers seeking alternative solutions to reduce the dependency on fossil-based fuels for transportation. A viable technology that enables significant improvements in the overall energy conversion efficiencies is the hybridization of conventional vehicle drive systems. This dissertation builds on prior hybrid powertrain development at the University of Idaho. Advanced vehicle models of a passenger car with a conventional powertrain and three different hybrid powertrain layouts were created using GT-Suite. These different powertrain models were validated against a variety of standard driving cycles. The overall fuel economy, energy consumption, and losses were monitored, and a comprehensive energy analysis was performed to compare energy sources and sinks. The GT-Suite model was then used to predict the formula hybrid SAE vehicle performance. Inputs to this model were a numerically predicted engine performance map, an electric motor torque curve, vehicle geometry, and road load parameters derived from a roll-down test. In this case study, the vehicle had a supervisory controller that followed a rule-based energy management strategy to insure a proper power split during hybrid mode operation. The supervisory controller parameters were optimized using discrete grid optimization method that minimized the total amount of fuel consumed during a specific urban driving cycle with an average speed of approximately 30 [mph]. More than a 15% increase in fuel economy was achieved by adding supervisory control and managing power split. The vehicle configuration without the supervisory controller displayed a fuel economy of 25 [mpg]. With the supervisory controller this rose to 29 [mpg]. Wider applications of this research include hybrid vehicle controller designs that can extend the range and survivability of military combat platforms. Furthermore, the

  3. Comments on the Joint Proposed Rulemaking to Establish Light-Duty Vehicle Greenhouse Gas Emission Standards and Corporate Average Fuel Economy Standards

    Energy Technology Data Exchange (ETDEWEB)

    Wenzel, Tom [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2009-10-27

    Tom Wenzel of Lawrence Berkeley National Laboratory comments on the joint rulemaking to establish greenhouse gas emission and fuel economy standards for light-duty vehicle, specifically on the relationship between vehicle weight and vehicle safety.

  4. Simulated Fuel Economy and Emissions Performance during City and Interstate Driving for a Heavy-Duty Hybrid Truck

    Energy Technology Data Exchange (ETDEWEB)

    Daw, C. Stuart; Gao, Zhiming; Smith, David E.; Laclair, Tim J.; Pihl, Josh A.; Edwards, K. Dean

    2013-04-08

    We compare simulated fuel economy and emissions for both conventional and hybrid class 8 heavy-duty diesel trucks operating over multiple urban and highway driving cycles. Both light and heavy freight loads were considered, and all simulations included full aftertreatment for NOx and particulate emissions controls. The aftertreatment components included a diesel oxidation catalyst (DOC), urea-selective catalytic NOx reduction (SCR), and a catalyzed diesel particulate filter (DPF). Our simulated hybrid powertrain was configured with a pre-transmission parallel drive, with a single electric motor between the clutch and gearbox. A conventional HD truck with equivalent diesel engine and aftertreatment was also simulated for comparison. Our results indicate that hybridization can significantly increase HD fuel economy and improve emissions control in city driving. However, there is less potential hybridization benefit for HD highway driving. A major factor behind the reduced hybridization benefit for highway driving is that there are fewer opportunities to utilize regenerative breaking. Our aftertreatment simulations indicate that opportunities for passive DPF regeneration are much greater for both hybrid and conventional trucks during highway driving due to higher sustained exhaust temperatures. When passive DPF regeneration is extensively utilized, the fuel penalty for particulate control is virtually eliminated, except for the 0.4%-0.9% fuel penalty associated with the slightly higher exhaust backpressure.

  5. Environmental, Economic, and Scalability Considerations and Trends of Selected Fuel Economy-Enhancing Biomass-Derived Blendstocks

    Energy Technology Data Exchange (ETDEWEB)

    Dunn, Jennifer B. [Systems; Biddy, Mary [National; Jones, Susanne [Energy; Cai, Hao [Systems; Benavides, Pahola Thathiana [Systems; Markham, Jennifer [National; Tao, Ling [National; Tan, Eric [National; Kinchin, Christopher [National; Davis, Ryan [National; Dutta, Abhijit [National; Bearden, Mark [Energy; Clayton, Christopher [Energy; Phillips, Steven [Energy; Rappé, Kenneth [Energy; Lamers, Patrick [Bioenergy

    2017-10-30

    24 biomass-derived compounds and mixtures, identified based on their physical properties, that could be blended into fuels to improve spark ignition engine fuel economy were assessed for their economic, technology readiness, and environmental viability. These bio-blendstocks were modeled to be produced biochemically, thermochemically, or through hybrid processes. To carry out the assessment, 17 metrics were developed for which each bio-blendstock was determined to be favorable, neutral, or unfavorable. Cellulosic ethanol was included as a reference case. Overall, bio-blendstock yields in biochemical processes were lower than in thermochemical processes, in which all biomass, including lignin, is converted to a product. Bio-blendstock yields were a key determinant in overall viability. Key knowledge gaps included the degree of purity needed for use as a bio-blendstock as compared to a chemical. Less stringent purification requirements for fuels could cut processing costs and environmental impacts. Additionally, more information is needed on the blendability of many of these bio-blendstocks with gasoline to support the technology readiness evaluation. Overall, the technology to produce many of these blendstocks from biomass is emerging and as it matures, these assessments must be revisited. Importantly, considering economic, environmental, and technology readiness factors in addition to physical properties of blendstocks that could be used to boost fuel economy can help spotlight those most likely to be viable in the near term.

  6. Quantifying the Effects of Idle-Stop Systems on Fuel Economy in Light-Duty Passenger Vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Jeff Wishart; Matthew Shirk

    2012-12-01

    Vehicles equipped with idle-stop (IS) systems are capable of engine shut down when the vehicle is stopped and rapid engine re-start for the vehicle launch. This capability reduces fuel consumption and emissions during periods when the engine is not being utilized to provide propulsion or to power accessories. IS systems are a low-cost and fast-growing technology in the industry-wide pursuit of increased vehicle efficiency, possibly becoming standard features in European vehicles in the near future. In contrast, currently there are only three non-hybrid vehicle models for sale in North America with IS systems and these models are distinctly low-volume models. As part of the United States Department of Energy’s Advanced Vehicle Testing Activity, ECOtality North America has tested the real-world effect of IS systems on fuel consumption in three vehicle models imported from Europe. These vehicles were chosen to represent three types of systems: (1) spark ignition with 12-V belt alternator starter; (2) compression ignition with 12-V belt alternator starter; and (3) direct-injection spark ignition, with 12-V belt alternator starter/combustion restart. The vehicles have undergone both dynamometer and on-road testing; the test results show somewhat conflicting data. The laboratory data and the portion of the on-road data in which driving is conducted on a prescribed route with trained drivers produced significant fuel economy improvement. However, the fleet data do not corroborate improvement, even though the data show significant engine-off time. It is possible that the effects of the varying driving styles and routes in the fleet testing overshadowed the fuel economy improvements. More testing with the same driver over routes that are similar with the IS system-enabled and disabled is recommended. There is anecdotal evidence that current Environmental Protection Agency fuel economy test procedures do not capture the fuel economy gains that IS systems produce in real

  7. The Miller cycle effects on improvement of fuel economy in a highly boosted, high compression ratio, direct-injection gasoline engine: EIVC vs. LIVC

    International Nuclear Information System (INIS)

    Li, Tie; Gao, Yi; Wang, Jiasheng; Chen, Ziqian

    2014-01-01

    Highlights: • At high load, LIVC is superior over EIVC in improving fuel economy. • The improvement with LIVC is due to advanced combustion phasing and increased pumping work. • At low load, EIVC is better than LIVC in improving fuel economy. • Pumping loss with EIVC is smaller than with LIVC at low load. • But heat release rate with EIVC is slower than with LIVC. - Abstract: A combination of downsizing, highly boosting and direct injection (DI) is an effective way to improve fuel economy of gasoline engines without the penalties of reduced torque or power output. At high loads, however, knock problem becomes severer when increasing the intake boosting. As a compromise, geometric compression ratio (CR) is usually reduced to mitigate knock, and the improvement of fuel economy is discounted. Application of Miller cycle, which can be realized by either early or late intake valve closing (EIVC or LIVC), has the potential to reduce the effective CR and suppress knock. In this paper, the effects of EIVC and LIVC on the fuel economy of a boosted DI gasoline production engine reformed with a geometric CR of 12.0 are experimentally compared at low and high loads. Compared to the original production engine with CR 9.3, at the high load operation, the brake specific fuel consumption (BSFC) is improved by 4.7% with CR12.0 and LIVC, while the effect of EIVC on improving BSFC is negligibly small. At the low load operation, combined with CR12.0, LIVC and EIVC improve the fuel economy by 6.8% and 7.4%, respectively, compared to the production engine. The mechanism behind the effects of LIVC and EIVC on improving the fuel economy is discussed. These results will be a valuable reference for engine designers and researchers

  8. Fueling the Gig Economy: A Case Study Evaluation of Upwork.com

    OpenAIRE

    Daryl D. Green; Craig Walker; Abdulrahman Alabulththim; Daniel Smith; Michele Phillips

    2018-01-01

    With recent downsizing of talented professionals and the power of globalization to provide opportunities for more underdeveloped countries, the gig economy is a source of influence in today’s generation of professionals. Online outsourcing media have shown to be valuable resources for companies who need a specific set of skills for a limited period. This case study evaluates Upwork.com, one of the leading freelance websites in the gig economy; this article provides insights on how others shou...

  9. Hydrogen fuel cell engines and related technologies

    Science.gov (United States)

    2001-12-01

    The manual documents the first training course developed on the use of hydrogen fuel cells in transportation. The manual contains eleven modules covering hydrogen properties, use and safety; fuel cell technology and its systems, fuel cell engine desi...

  10. Fueling the Gig Economy: A Case Study Evaluation of Upwork.com

    Directory of Open Access Journals (Sweden)

    Daryl D. Green

    2018-02-01

    Full Text Available With recent downsizing of talented professionals and the power of globalization to provide opportunities for more underdeveloped countries, the gig economy is a source of influence in today’s generation of professionals. Online outsourcing media have shown to be valuable resources for companies who need a specific set of skills for a limited period. This case study evaluates Upwork.com, one of the leading freelance websites in the gig economy; this article provides insights on how others should evaluate the power of this new economy in terms of opportunities for small businesses, entrepreneurs, and freelancers. Upwork has led the pack by providing a flexible platform for freelancers worldwide, including coders, writers, and web developers, putting businesses in touch with reasonably priced workers. The study begins by exploring the attributes of the gig economy. Data collection is achieved through qualitative analysis. The application of these conclusions could increase the survival rate of new freelancers on Upwork.com and in the gig economy. The study is significant because this research widens contemporary assumptions about strategic thinking for individuals engaged in e-commerce.

  11. Modeling and Parameterization of Fuel Economy in Heavy Duty Vehicles (HDVs

    Directory of Open Access Journals (Sweden)

    Yunjung Oh

    2014-08-01

    Full Text Available The present paper suggests fuel consumption modeling for HDVs based on the code from the Japanese Ministry of the Environment. Two interpolation models (inversed distance weighted (IDW and Hermite and three types of fuel efficiency maps (coarse, medium, and dense were adopted to determine the most appropriate combination for further studies. Finally, sensitivity analysis studies were conducted to determine which parameters greatly impact the fuel efficiency prediction results for HDVs. While vitiating each parameter at specific percentages (±1%, ±3%, ±5%, ±10%, the change rate of the fuel efficiency results was analyzed, and the main factors affecting fuel efficiency were summarized. As a result, the Japanese transformation algorithm program showed good agreement with slightly increased prediction accuracy for the fuel efficiency test results when applying the Hermite interpolation method compared to IDW interpolation. The prediction accuracy of fuel efficiency remained unchanged regardless of the chosen fuel efficiency map data density. According to the sensitivity analysis study, three parameters (fuel consumption map data, driving force, and gross vehicle weight have the greatest impact on fuel efficiency (±5% to ±10% changes.

  12. A review on idling reduction strategies to improve fuel economy and reduce exhaust emissions of transport vehicles

    International Nuclear Information System (INIS)

    Shancita, I.; Masjuki, H.H.; Kalam, M.A.; Rizwanul Fattah, I.M.; Rashed, M.M.; Rashedul, H.K.

    2014-01-01

    Highlights: • Introduce various idling reduction technologies for transport vehicles. • Exhibit their energy use, advantages, disadvantages to understand their capability. • Conduct critical review to improve fuel economy and exhaust emissions. • Suggest better technology according to their performance ability. - Abstract: To achieve reductions in vehicle idling, strategies and actions must be taken to minimize the time spent by drivers idling their engines. A number of benefits can be obtained in limiting the idling time. These benefits include savings in fuel use and maintenance costs, vehicle life extension, and reduction in exhaust emissions. The main objective of idling reduction (IR) devices is to reduce the amount of energy wasted by idling trucks, rail locomotives, and automobiles. During idling, gasoline vehicles emit a minimum amount of nitrogen oxides (NO x ) and negligible particulate matter (PM). However, generally a large amount of carbon monoxide (CO) and hydrocarbons (HC) are produced from these vehicles. Gasoline vehicles consume far more fuel at an hourly rate than their diesel counterparts during idling. Higher NOx and comparatively larger PM are produced by diesel vehicles than gasoline vehicles on the average during idling. Auxiliary power unit (APU), direct-fired heaters, fuel cells, thermal storage system, truck stop electrification, battery-based systems, engine idle management (shutdown) systems, electrical (shore power) solutions, cab comfort system, and hybridization are some of the available IR technologies whose performances for reducing fuel consumption and exhaust emissions have been compared. This paper analyzes the availability and capability of most efficient technologies to reduce fuel consumption and exhaust emissions from diesel and gasoline vehicles by comparing the findings of previous studies. The analysis reveals that among all the options direct fired heaters, APUs and electrified parking spaces exhibit better

  13. The reliability of the Extra Load Index as a measure of relative load carriage economy.

    Science.gov (United States)

    Hudson, Sean; Cooke, Carlton; Lloyd, Ray

    2017-09-01

    The aim of this study was to measure the reliability of the extra load index (ELI) as a method for assessing relative load carriage economy. Seventeen volunteers (12 males, 5 females) performed walking trials at 3 km·h -1 , 6 km·h -1 and a self-selected speed. Trial conditions were repeated 7 days later to assess test-retest reliability. Trials involved four 4-minute periods of walking, each separated by 5 min of rest. The initial stage was performed unloaded followed in a randomised order by a second unloaded period and walking with backpacks of 7 and 20 kg. Results show ELI values did not differ significantly between trials for any of the speeds (p = 0.46) with either of the additional loads (p = 0.297). The systematic bias, limits of agreement and coefficients of variation were small in all trial conditions. We conclude the ELI appears to be a reliable measure of relative load carriage economy. Practitioner Summary: This paper demonstrates that the ELI is a reliable measure of load carriage economy at a range of walking speeds with both a light and heavy load. The ELI, therefore, represents a useful tool for comparing the relative economy associated with different load carriage systems.

  14. Fuel Economy Improvement of a Heavy-Duty Powertrain by Using Hardware-in-Loop Simulation and Calibration

    Directory of Open Access Journals (Sweden)

    Bolan Liu

    2015-09-01

    Full Text Available Fuel economy efficiency is one of the most important parameters for vehicle powertrains, which is of particular interest for heavy-duty powertrain calibration. Conventionally, this work relies heavily on road tests, which cost more and may lead to long duration product development cycles. The paper proposes a novel hardware-in-loop modeling and calibration method to work it out. A dSPACE hardware-based test bench was successfully established and validated, which is valuable for a more efficient and easier shift schedule in calibration. Meanwhile, a real-time dynamic powertrain model, including a diesel engine, torque converter, gear box and driver model was built. Typical driving cycles that both velocity and slope information were constructed for different road conditions. A basic economic shift schedule was initially calculated and then optimal calibrated by the test bench. The results show that there is an optimal relationship between an economic shift schedule and speed regulation. By matching the best economic shift schedule regulation to different road conditions; the fuel economy of vehicles can be improved. In a smooth driving cycle; when the powertrain applies a larger speed regulation such as 12% and the corresponding shift schedule; the fuel consumption is smaller and is reduced by 13%. In a complex driving cycle, when the powertrain applies a smaller speed regulation such as 5% along with the corresponding shift schedule; the fuel consumption is smaller and is reduced by 5%. The method thus can provide guidance for economic calibration experiments of off-road heavy-duty vehicles.

  15. 1998 Annual Study Report. Standardization of methods for measuring fuel economy of hybrid electric vehicles; 1998 nendo seika hokokusho. Hybrid denki jidosha no nenpi sokutei hoho no hyojunka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The hybrid electric vehicle (HEV) has been attracting attention as a clean energy vehicle, because it will potentially show higher fuel economy and release smaller quantities of exhaust emissions than the conventional internal combustion engine, and also will be potentially advantageous over the electric vehicle in that it needs no charging infrastructures and less cost. However, there are many types of hybrid vehicle systems, and, for them to be commercialized on a large scale, it is urgently necessary to establish the fuel economy measurement method. The 1998 R and D efforts were directed to analysis of the effects of the hybrid-characteristic factors (SOC of the propulsion battery and regenerative braking) on fuel economy and exhaust emissions. As a result, it is found that changed SOC before and after the tests must be corrected to determine fuel economy and that it is possible. The method for measuring the effects of regenerative braking should be further developed, because the data collected while the vehicle is running on road and on a two-wheel chassis dynamometer are not clearly distinguished from each other. The exhaust emissions are also sensitive to the changed SOC, correction for which, however, is not as easy as that for fuel economy. (NEDO)

  16. Monolithic fuel injector and related manufacturing method

    Science.gov (United States)

    Ziminsky, Willy Steve [Greenville, SC; Johnson, Thomas Edward [Greenville, SC; Lacy, Benjamin [Greenville, SC; York, William David [Greenville, SC; Stevenson, Christian Xavier [Greenville, SC

    2012-05-22

    A monolithic fuel injection head for a fuel nozzle includes a substantially hollow vesicle body formed with an upstream end face, a downstream end face and a peripheral wall extending therebetween, an internal baffle plate extending radially outwardly from a downstream end of the bore, terminating short of the peripheral wall, thereby defining upstream and downstream fuel plenums in the vesicle body, in fluid communication by way of a radial gap between the baffle plate and the peripheral wall. A plurality of integral pre-mix tubes extend axially through the upstream and downstream fuel plenums in the vesicle body and through the baffle plate, with at least one fuel injection hole extending between each of the pre-mix tubes and the upstream fuel plenum, thereby enabling fuel in the upstream plenum to be injected into the plurality of pre-mix tubes. The fuel injection head is formed by direct metal laser sintering.

  17. INFLUENCE OF RELATIONS WITH INTERNATIONAL FINANCIAL INSTITUTIONS ON INSTITUTIONAL TRANSFORMATIONS OF ECONOMY

    Directory of Open Access Journals (Sweden)

    Galyna POCHENCHUK

    2014-12-01

    Full Text Available The article deals with the problem of the impact of transitional countries cooperation with international financial institutions on institutional changes which take place in emerging market economies, on the base of Ukraine. Research is carried out from the standpoint of institutional theory. The main reforms that took place in emerging market economy countries were based on the Washington Consensus strategy recommended by international financial institutions. The results of implementing this strategy are varied in different countries. In Ukraine strict adherence to requirements in the early stages of reforms without internal institutional conditions and characteristics led to a deep and protracted crisis of forming a "transformational stability." The general formal institutions of the market economy have been created according to the neoliberal concept which is provided by IFIs. However, experience of transitive economies including Ukraine, confirms the ineffectiveness of many established formal institutions borrowed from the developed countries. The author reviews the basic theory of institutional changes, argues that the terms of cooperation circulated by international financial institutions not only affect economic development strategy, but also determine the role of the national government in relations with markets. Under present conditions prevailing in Ukraine, it is impossible to manage without assistance of international financial institutions. But we need to pay more attention to technical and advisory cooperation in realization of institutional reforms, and credits – to take as a required time for receiving the results of reforms.

  18. Status of Occupational Health and Safety and Related Challenges in Expanding Economy of Tanzania.

    Science.gov (United States)

    Mrema, Ezra J; Ngowi, Aiwerasia V; Mamuya, Simon H D

    2015-01-01

    Occupational health and safety is related with economic activities undertaken in the country. As the economic activities grow and expand, occupational injuries and diseases are more likely to increase among workers in different sectors of economy such as agriculture, mining, transport, and manufacture. This may result in high occupational health and safety services demand, which might be difficult to meet by developing countries that are prioritizing economic expansion without regard to their impact on occupational health and safety. To describe the status of occupational health and safety in Tanzania and outline the challenges in provision of occupational health services under the state of an expanding economy. Tanzania's economy is growing steadily, with growth being driven by communications, transport, financial intermediation, construction, mining, agriculture, and manufacturing. Along with this growth, hazards emanating from work in all sectors of the economy have increased and varied. The workers exposed to these hazards suffer from illness and injuries and yet they are not provided with adequate occupational health services. Services are scanty and limited to a few enterprises that can afford it. Existing laws and regulations are not comprehensive enough to cover the entire population. Implementation of legislation is weak and does not protect the workers. Most Tanzanians are not covered by the occupational health and safety law and do not access occupational health services. Thus an occupational health and safety services strategy, backed by legislations and provided with the necessary resources (competent experts, financial and technological resources), is a necessity in Tanzania. The existing legal provisions require major modifications to meet international requirements and standards. OHS regulations and legislations need refocusing, revision, and strengthening to cover all working population. Capacities should be improved through training and research

  19. Integration of Forest Fuel Handling in the Ordinary Forestry. Studies on Forestry, Technology and Economy of Forest Fuel Production in Lithuania

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Lars [Regional Forestry Board of Vaermland-Oerebro, Karlstad (Sweden); Budrys, Renatas [Lithuanian Forest Research Inst. (Lithuania)

    2002-07-01

    During the year 2000, The Swedish Forest Administration and Forest Department, Ministry of Environment in Lithuania, started a bilateral co-operation project, named: 'Swedish Lithuanian Wood Fuel Development Project', financed by the Swedish Energy Agency. The project was divided into 2 phases. The first phase objectives were to make a feasibility study in the eastern part of Lithuania and to identify the present conditions for the utilization of wood fuel within seven state forest enterprises and to define a demonstration and experimental area for the phase 2. The purpose of this work was to find solutions for creating horizontal and vertical integration in the handling of forest fuels in ordinary forestry and supply systems. The aim would be to give specific recommendations on which methods are the most suitable and profitable and on what type of equipment to use for various conditions and by the means of demonstrations to show how to integrate the positive results into the ordinary forestry activities. Different kinds of activities have been carried out to ensure capacity building and development on other levels within the system. 3 activity groups were established and have been working side by side with the appointed team leaders for each activity group from the institutions leading in the specific area within the forest sector in Lithuania. Swedish specialists from the Swedish Forest Administration were involved into the project and the activity groups as well. Lithuanian Forest Research Institute was involved into the project with research support. Additional to the project a mobile drum wood chipper was purchased from Sweden. 3 separate investigations have been conducted, one by Kaunas Univ. of Tech. on the analysis and estimation of material balance in Lithuania saw milling industry, another by Forest Economy Centre on wood fuel produced in industry in Lithuania and the third one by Lithuanian Energy Institute and AF international on Bio fuel

  20. Alternative Fuels Data Center: Hydrogen Related Links

    Science.gov (United States)

    marketing zero-emission proton exchange membrane (PEM) fuel cells for transportation and power generation production and use. Energy Management Institute The Energy Management Institute publishes the Alternative

  1. Fuel reprocessing plant - no solution for the economy of the region

    International Nuclear Information System (INIS)

    Elvers, G.

    1986-01-01

    Both for the construction and operation stage, the direct and indirect impact of the fuel reprocessing plant on employment on the whole will be negative. It is not altogether certain either that there will be no adverse effects for the areas of tourism. The top organization of German trade unions (DGB) holds that a different structure-political concept from the one represented by the large-scale project of the fuel reprocessing plant would be more appropriate for the region. Employment in the steel and construction industries must be safeguarded by corresponding programmes, and new employment must be created in small- and medium-size companies. (DG) [de

  2. Foucault's contributions for understanding power relations in British classical political economy

    Directory of Open Access Journals (Sweden)

    Danielle Guizzo

    2015-05-01

    Full Text Available This paper analyzes the strategic role played by British classical political economy in constructing new technologies of power. Michel Foucault drew attention to a change that political economists promoted concerning the role of the state, which has been overlooked by historians of economic thought. This paper explores the main arguments provided by the most important British political economists of the 18th and 19th centuries on what concerns population management, State's role and economic dynamics in order to examine Foucault's considerations. Although British classical political economy consolidated the mechanism of markets and economic individuality, thus creating a system of truth that changed economic norms and practices, its discourse also established a political conduct that was responsible for creating mechanisms of control that disseminated new forms of power relations.

  3. 41 CFR 102-34.55 - Are there fleet average fuel economy standards we must meet?

    Science.gov (United States)

    2010-07-01

    ... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Are there fleet average... Management Federal Property Management Regulations System (Continued) FEDERAL MANAGEMENT REGULATION PERSONAL PROPERTY 34-MOTOR VEHICLE MANAGEMENT Obtaining Fuel Efficient Motor Vehicles § 102-34.55 Are there fleet...

  4. Hybrid Taxis Give Fuel Economy a Lift -Clean Cities Fleet Experiences -

    Energy Technology Data Exchange (ETDEWEB)

    None

    2009-04-01

    The hybrid taxis are able to achieve about twice the gas mileage of a conventional taxi while helping cut gasoline use and fuel costs. Tax credits and other incentives are helping both company owners and drivers make the switch to hybrids.

  5. Effect of Weight and Roadway Grade on the Fuel Economy of Class-8 Frieght Trucks

    Energy Technology Data Exchange (ETDEWEB)

    Franzese, Oscar [ORNL; Davidson, Diane [ORNL

    2011-11-01

    In 2006-08, the Oak Ridge National Laboratory, in collaboration with several industry partners, collected real-world performance and situational data for long-haul operations of Class-8 trucks from a fleet engaged in normal freight operations. Such data and information are useful to support Class-8 modeling of combination truck performance, technology evaluation efforts for energy efficiency, and to provide a means of accounting for real-world driving performance within combination truck research and analyses. The present study used the real-world information collected in that project to analyze the effects that vehicle speed and vehicle weight have on the fuel efficiency of Class-8 trucks. The analysis focused on two type of terrains, flat (roadway grades ranging from -1% to 1%) and mild uphill terrains (roadway grades ranging from 1% to 3%), which together covered more than 70% of the miles logged in the 2006-08 project (note: almost 2/3 of the distance traveled on mild uphill terrains was on terrains with 1% to 2% grades). In the flat-terrain case, the results of the study showed that for light and medium loads, fuel efficiency decreases considerably as speed increases. For medium-heavy and heavy loads (total vehicle weight larger than 65,000 lb), fuel efficiency tends to increase as the vehicle speed increases from 55 mph up to about 58-60 mph. For speeds higher than 60 mph, fuel efficiency decreases at an almost constant rate with increasing speed. At any given speed, fuel efficiency decreases and vehicle weight increases, although the relationship between fuel efficiency and vehicle weight is not linear, especially for vehicle weights above 65,000 lb. The analysis of the information collected while the vehicles were traveling on mild upslope terrains showed that the fuel efficiency of Class-8 trucks decreases abruptly with vehicle weight ranging from light loads up to medium-heavy loads. After that, increases in the vehicle weight only decrease fuel

  6. 40 CFR 600.208-08 - Calculation of FTP-based and HFET-based fuel economy values for a model type.

    Science.gov (United States)

    2010-07-01

    ... the original base level fuel economy values); and (iii) All subconfigurations within the new base... separating subconfigurations from an existing base level and placing them into a new base level. The new base... this paragraph, as containing a new basic engine. The manufacturer will be permitted to designate such...

  7. The Application of High Energy Ignition and Boosting/Mixing Technology to Increase Fuel Economy in Spark Ignition Gasoline Engines by Increasing EGR Dilution Capability

    Energy Technology Data Exchange (ETDEWEB)

    Keating, Edward [General Motors LLC, Pontiac, MI (United States); Gough, Charles [General Motors LLC, Pontiac, MI (United States)

    2015-07-07

    This report summarizes activities conducted in support of the project “The Application of High Energy Ignition and Boosting/Mixing Technology to Increase Fuel Economy in Spark Ignition Gasoline Engines by Increasing EGR Dilution Capability” under COOPERATIVE AGREEMENT NUMBER DE-EE0005654, as outlined in the STATEMENT OF PROJECT OBJECTIVES (SOPO) dated May 2012.

  8. NRC committee on assessment of technologies for improving fuel economy of light-duty vehicles: Meeting with DOT Volpe Center staff - February 27, 2013

    Science.gov (United States)

    2013-02-27

    On February 27, 2013 National Research Council's Committee on Fuel Economy of Light-Duty Vehicles, Phase 2 held a meeting at the John A. Volpe National Transportation Systems Center on the Volpe Model and Other CAFE Issues. The meeting objectives wer...

  9. The Neoindustrial Principles for the Development of Integration Relations in the Agrarian Sector of Economy

    Directory of Open Access Journals (Sweden)

    Hutorov Andrii O.

    2017-08-01

    Full Text Available The article is aimed at elaborating the neoindustrial principles for the development of integration relations in the agrarian sector of economy. It has been shown that the engine of sectoral development and economic growth in the context of neoliberal globalization are the integration relations formed by the product principle and intrinsically linked to the neoindustrial transformation of the agro-industrial potential. The article explores the lack of options when choosing a national model for the sectoral development of economy: vertical integration of advanced playback, neoindustrialization, and economic security. It has been proven that the mutual relationship between the socio-economic formations and the strategies for integration interaction is organic. The replacement of the functional target setting of economic system at all levels of the hierarchy from the maximum profit to the maximum of the cumulative newly created (added value has been substantiated. A conceptual model for the development of the agrarian sector through integration and neoindustrialization has been accomplished, as well as the principles of strategic management of the system of integration relations have been elaborated. The main forms of implementation of the integration relations with the centralized and decentralized models of neoindustrial development of the agrarian sector have been defined.

  10. China’s Strategic Investments and Its Relations with Developing Economies

    Directory of Open Access Journals (Sweden)

    Radu-Marcel Joia

    2011-05-01

    Full Text Available 2010 brings news regarding China's economic strategy. It has strengthened its trade relations withemerging economies, making significant investments, plus significant imports and exports, proving again thatit is the first commercial power in the world. China, considered being "the manufacturer of the world", alongwith Brazil and Russia, major exporters of raw materials, and India, the country which offers the cheapesttechnology services, has made the world organization, named as BRIC. In 2009, China has consolidated itsposition as the main trading partner with Brazil, a position that enabled it in 2010 to become the largestinvestor in the Brazilian territory. One of the most important Chinese strategies is the monetary one, throughwhich China is trying to grow internationally Yuan’s importance, reducing the dependence on the dollar bydriving autonomous trade flows. It is expected that Yuan will become the main currency in Asia, main goalthat will be achieved by the constitution of large reserves of Yuan on the Asian territory. Knowledge ofChinese economic policy and relations with emerging economies is essential, since 2010 shows the economicpower of this nation, the largest trading power in the world, which has led the economists to study China'seconomic situation. We used for this study, data extracted from UNCTAD and ASEAN’s reports from 2010,plus various U.S. studies on China's geostrategic position. China’s geostrategic position is an important one,especially compared with the other BRIC countries, making energy investments in the Middle East, strategythat was adopted also by India and Russia; so Russia and China created ESPO project, Eastern Siberia -Pacific - Ocean, through which China is making huge investments in energy and Russia is trying to stand outfor European markets. Through this paper, we tried to evidence China’s financial and trade relations withUSA, European Union and emerging economies, in the context of a severe

  11. Hybrid Taxis Give Fuel Economy a Lift, Clean Cities, Fleet Experiences, April 2009 (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2009-04-01

    Clean Cities helped Boston, San Antonio, and Cambridge create hybrid taxi programs. The hybrid taxis are able to achieve about twice the gas mileage of a conventional taxi while helping cut gasoline use and fuel costs. Tax credits and other incentives are helping both company owners and drivers make the switch to hybrids. Program leaders have learned some important lessons other cities can benefit from including learning a city's taxi structure, relaying benefits to drivers, and understanding the needs of owners.

  12. On the Relation between Tax Rates and Evasion in a Multi-period Economy

    OpenAIRE

    Jordi Caball?Author-Email:; Judith Panad?

    2001-01-01

    We extend the basic tax evasion model to a multi-period economy exhibiting sustained growth. When individuals conceal part of their true income from the tax authority, they face the risk of being audited and hence of paying the corresponding fine. Both taxes and fines determine individual saving and the rate of capital accumulation. In this context we show that the sign of the relation between the level of the tax rate and the amount of evaded income is the same as that obtained in static set...

  13. On the relation between tax rates and evasion in a multi-period economy

    OpenAIRE

    Caballé, Jordi

    2006-01-01

    We extend the basic tax evasion model to a multi-period economy exhibiting sustained growth. When individuals conceal part of their true income from the tax authority, they face the risk of being audited and hence of paying the corresponding fine. Both taxes and fines determine individual saving and the rate of capital accumulation. In this context we show that the sign of the relation between the level of the tax rate and the amount of evaded income is the same as that obtained in static set...

  14. Hydrogen economy

    Energy Technology Data Exchange (ETDEWEB)

    Pahwa, P.K.; Pahwa, Gulshan Kumar

    2013-10-01

    In the future, our energy systems will need to be renewable and sustainable, efficient and cost-effective, convenient and safe. Hydrogen has been proposed as the perfect fuel for this future energy system. The availability of a reliable and cost-effective supply, safe and efficient storage, and convenient end use of hydrogen will be essential for a transition to a hydrogen economy. Research is being conducted throughout the world for the development of safe, cost-effective hydrogen production, storage, and end-use technologies that support and foster this transition. This book discusses hydrogen economy vis-a-vis sustainable development. It examines the link between development and energy, prospects of sustainable development, significance of hydrogen energy economy, and provides an authoritative and up-to-date scientific account of hydrogen generation, storage, transportation, and safety.

  15. Fuel assembly

    International Nuclear Information System (INIS)

    Chaki, Masao; Nishida, Koji; Karasawa, Hidetoshi; Kanazawa, Toru; Orii, Akihito; Nagayoshi, Takuji; Kashiwai, Shin-ichi; Masuhara, Yasuhiro

    1998-01-01

    The present invention concerns a fuel assembly, for a BWR type nuclear reactor, comprising fuel rods in 9 x 9 matrix. The inner width of the channel box is about 132mm and the length of the fuel rods which are not short fuel rods is about 4m. Two water rods having a circular cross section are arranged on a diagonal line in a portion of 3 x 3 matrix at the center of the fuel assembly, and two fuel rods are disposed at vacant spaces, and the number of fuel rods is 74. Eight fuel rods are determined as short fuel rods among 74 fuel rods. Assuming the fuel inventory in the short fuel rod as X(kg), and the fuel inventory in the fuel rods other than the short fuel rods as Y(kg), X and Y satisfy the relation: X + Y ≥ 173m, Y ≤ - 9.7X + 292, Y ≤ - 0.3X + 203 and X > 0. Then, even when the short fuel rods are used, the fuel inventory is increased and fuel economy can be improved. (I.N.)

  16. Experimental programmes related to high burnup fuel

    International Nuclear Information System (INIS)

    Vasudeva Rao, P.R.; Vidhya, R.; Ananthasivan, K.; Srinivasan, T.G.; Nagarajan, K.

    2002-01-01

    The experimental programmes undertaken at IGCAR with regard to high burn-up fuels fall under the following categories: a) studies on fuel behaviour, b) development of extractants for aqueous reprocessing and c) development of non-aqueous reprocessing techniques. An experimental programme to measure the carbon potential in U/Pu-FP-C systems by methane-hydrogen gas equilibration technique has been initiated at IGCAR in order to understand the evolution of fuel and fission product phases in carbide fuel at high burn-up. The carbon potentials in U-Mo-C system have been measured by this technique. The free energies and enthalpies of formation of LaC 2 , NdC 2 and SmC 2 have been measured by measuring the vapor pressures of CO over the region Ln 2 O 3 -LnC 2 -C during the carbothermic reduction of Ln 2 O 3 by C. The decontamination from fission products achieved in fuel reprocessing depends strongly on the actinide loading of the extractant phase. Tri-n-butyl phosphate (TBP), presently used as the extractant, does not allow high loadings due to its propensity for third phase formation in the extraction of Pu(IV). A detailed study of the allowable Pu loadings in TBP and other extractants has been undertaken in IGCAR, the results of which are presented in this paper. The paper also describes the status of our programme to develop a non-aqueous route for the reprocessing of fast reactor fuels. (author)

  17. JPRS Report, Soviet Union, World Economy and International Relations, No. 1, January 1988.

    Science.gov (United States)

    1988-05-23

    ous sectors of the economy. Such sections might just as happily have been accommodated in any book on the country’s economy or in an economico ...of the military sector of the economy. Admitting the need for highly developed productive forces in order to build up the military might the author...military business. The high level of monopolization characteristic of the Japanese economy’s military sector is combined with a comparatively low volume

  18. Decomposing Fuel Economy and Greenhouse Gas Regulatory Standards in the Energy Conversion Efficiency and Tractive Energy Domain

    Energy Technology Data Exchange (ETDEWEB)

    Pannone, Greg [Novation Analytics; Thomas, John F [ORNL; Reale, Michael [Novation Analytics; Betz, Brian [Novation Analytics

    2017-01-01

    The three foundational elements that determine mobile source energy use and tailpipe carbon dioxide (CO2) emissions are the tractive energy requirements of the vehicle, the on-cycle energy conversion efficiency of the propulsion system, and the energy source. The tractive energy requirements are determined by the vehicle's mass, aerodynamic drag, tire rolling resistance, and parasitic drag. Oncycle energy conversion of the propulsion system is dictated by the tractive efficiency, non-tractive energy use, kinetic energy recovery, and parasitic losses. The energy source determines the mobile source CO2 emissions. For current vehicles, tractive energy requirements and overall energy conversion efficiency are readily available from the decomposition of test data. For future applications, plausible levels of mass reduction, aerodynamic drag improvements, and tire rolling resistance can be transposed into the tractive energy domain. Similarly, by combining thermodynamic, mechanical efficiency, and kinetic energy recovery fundamentals with logical proxies, achievable levels of energy conversion efficiency can be established to allow for the evaluation of future powertrain requirements. Combining the plausible levels of tractive energy and on-cycle efficiency provides a means to compute sustainable vehicle and propulsion system scenarios that can achieve future regulations. Using these principles, the regulations established in the United States (U.S.) for fuel consumption and CO2 emissions are evaluated. Fleet-level scenarios are generated and compared to the technology deployment assumptions made during rule-making. When compared to the rule-making assumptions, the results indicate that a greater level of advanced vehicle and propulsion system technology deployment will be required to achieve the model year 2025 U.S. standards for fuel economy and CO2 emissions.

  19. Methodical Approach to Estimation of Energy Efficiency Parameters of the Economy Under the Structural Changes in the Fuel And Energy Balance (on the Example of Baikal Region

    Directory of Open Access Journals (Sweden)

    Boris Grigorievich Saneev

    2013-12-01

    Full Text Available The authors consider a methodical approach which allows estimating energy efficiency parameters of the region’s economy using a fuel and energy balance (FEB. This approach was tested on the specific case of Baikal region. During the testing process the authors have developed ex ante and ex post FEBs and estimated energy efficiency parameters such as energy-, electro- and heat capacity of GRP, coefficients of useful utilization of fuel and energy resources and a monetary version of FEB. Forecast estimations are based on assumptions and limitations of technologically-intensive development scenario of the region. Authors show that the main factor of structural changes in the fuel and energy balance will be the large-scale development of hydrocarbon resources in Baikal region. It will cause structural changes in the composition of both the debit and credit of FEB (namely the structure of export and final consumption of fuel and energy resources. Authors assume that the forecast structural changes of the region’s FEB will significantly improve energy efficiency parameters of the economy: energy capacity of GRP will decrease by 1,5 times in 2010– 2030, electro and heat capacity – 1,9 times; coefficients of useful utilization of fuel and energy resources will increase by 3–5 p.p. This will save about 20 million tons of fuel equivalent (about 210 billion rubles in 2011 the prices until 2030

  20. Change in running kinematics after cycling are related to alterations in running economy in triathletes.

    Science.gov (United States)

    Bonacci, Jason; Green, Daniel; Saunders, Philo U; Blanch, Peter; Franettovich, Melinda; Chapman, Andrew R; Vicenzino, Bill

    2010-07-01

    Emerging evidence suggests that cycling may influence neuromuscular control during subsequent running but the relationship between altered neuromuscular control and run performance in triathletes is not well understood. The aim of this study was to determine if a 45 min high-intensity cycle influences lower limb movement and muscle recruitment during running and whether changes in limb movement or muscle recruitment are associated with changes in running economy (RE) after cycling. RE, muscle activity (surface electromyography) and limb movement (sagittal plane kinematics) were compared between a control run (no preceding cycle) and a run performed after a 45 min high-intensity cycle in 15 moderately trained triathletes. Muscle recruitment and kinematics during running after cycling were altered in 7 of 15 (46%) triathletes. Changes in kinematics at the knee and ankle were significantly associated with the change in VO(2) after cycling (precruitment in some triathletes and that changes in kinematics, especially at the ankle, are closely related to alterations in running economy after cycling. Copyright 2010 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

  1. Experience related to the safety of advanced LMFBR fuel elements

    International Nuclear Information System (INIS)

    Kerrisk, J.F.

    1975-07-01

    Experiments and experience relative to the safety of advanced fuel elements for the liquid metal fast breeder reactor are reviewed. The design and operating parameters and some of the unique features of advanced fuel elements are discussed breifly. Transient and steady state overpower operation and loss of sodium bond tests and experience are discussed in detail. Areas where information is lacking are also mentioned

  2. Fuel Economy and Emissions Effects of Low Tire Pressure, Open Windows, Roof Top and Hitch-Mounted Cargo, and Trailer

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, John F [ORNL; Huff, Shean P [ORNL; West, Brian H [ORNL

    2014-01-01

    To quantify the fuel economy (FE) effect of some common vehicle accessories or alterations, a compact passenger sedan and a sport utility vehicle (SUV) were subjected to SAE J2263 coastdown procedures. Coastdowns were conducted with low tire pressure, all windows open, with a roof top or hitch-mounted cargo carrier, and with the SUV pulling an enclosed cargo trailer. From these coastdowns, vehicle dynamometer coefficients were developed which enabled the execution of vehicle dynamometer experiments to determine the effect of these changes on vehicle FE and emissions over standard drive cycles and at steady highway speeds. The FE penalty associated with the rooftop cargo box mounted on the compact sedan was as high as 25-27% at higher speeds, where the aerodynamic drag is most pronounced. For both vehicles, use of a hitch mounted cargo tray carrying a similar load resulted in very small FE penalties, unlike the rooftop cargo box. The results for the SUV pulling a 3500 pound enclosed cargo trailer were rather dramatic, resulting in FE penalties ranging from 30%, for the city cycle, to 50% at 80 mph, at which point significant CO generation indicated protective enrichment due to high load. Low tire pressure cases resulted in negligible to 10% FE penalty depending on the specific case and test point. Driving with all four windows open decreased FE by 4-8.5% for the compact sedan, and 1-4% for the SUV.

  3. Assessment of effects of maturity of Japan`s economy and society and improvement in automotive fuel consumption on demand for automotive fuels; Nippon keizai shakai no seijukuka to nenpi kaizen ga jidoshayo nenryo juyo ni ataeru eikyo hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Shimomura, S. [The Institute of Energy Economics, Tokyo (Japan)

    1998-04-01

    This paper evaluates impacts of the maturity of Japan`s economy and society and the improvement in automotive fuel efficiency on the demand for automotive fuels by FY 2010. Standard case and lower order case were examined. When the traffic volume of passenger cars in FY 1995 is assumed to be 100, it become 121 and 119 in standard and lower order cases, respectively. The traffic volume of lorries become 106 and 102 in standard and lower order cases, respectively, which showed a rather small growth. Deterioration rate of the fuel consumption was estimated by considering the difference in fuel consumption of new cars and existing cars. Although the fuel consumption will be lowered by FY 2000 when the cassation rate of ordinary passenger cars will rapidly increase, the impact will be lowered after that. For lorries for commercial use, the running fuel consumption will be gradually lowered due to the increased carrying capacity and vehicle weight a lorry with improving the transportation efficiency. Decreased running speed by traffic jam is also a cause of the deterioration of fuel consumption. When a policy of improvement in the fuel consumption is promoted in a background of CO2 issues, the fuel consumption of each vehicle will be gradually improved. The peak of fuel demand will be in FY 2005 by considering the changes in economical and social structures and the improvement in fuel consumption for the environmental protection. 5 figs., 3 tabs.

  4. Forests, food, and fuel in the tropics: the uneven social and ecological consequences of the emerging political economy of biofuels.

    Science.gov (United States)

    Dauvergne, Peter; Neville, Kate J

    2010-01-01

    The global political economy of biofuels emerging since 2007 appears set to intensify inequalities among the countries and rural peoples of the global South. Looking through a global political economy lens, this paper analyses the consequences of proliferating biofuel alliances among multinational corporations, governments, and domestic producers. Since many major biofuel feedstocks - such as sugar, oil palm, and soy - are already entrenched in industrial agricultural and forestry production systems, the authors extrapolate from patterns of production for these crops to bolster their argument that state capacities, the timing of market entry, existing institutions, and historical state-society land tenure relations will particularly affect the potential consequences of further biofuel development. Although the impacts of biofuels vary by region and feedstock, and although some agrarian communities in some countries of the global South are poised to benefit, the analysis suggests that already-vulnerable people and communities will bear a disproportionate share of the costs of biofuel development, particularly for biofuels from crops already embedded in industrial production systems. A core reason, this paper argues, is that the emerging biofuel alliances are reinforcing processes and structures that increase pressures on the ecological integrity of tropical forests and further wrest control of resources from subsistence farmers, indigenous peoples, and people with insecure land rights. Even the development of so-called 'sustainable' biofuels looks set to displace livelihoods and reinforce and extend previous waves of hardship for such marginalised peoples.

  5. Review of spent fuel related issues in SKB's SR 97

    International Nuclear Information System (INIS)

    Grambow, B.

    2000-01-01

    The solid waste form 'spent fuel' constitutes both the dominant radionuclide source as well as a first radionuclide retention barrier of a planned future high level nuclear waste isolation systems in deep granite formations. In order to evaluate the performance of spent fuel as part of the multibarrier containment system in a deep repository, the radionuclide release properties in groundwater must be predicted over very long time periods. Radionuclide release is not an inherent materials property of the fuel but depends, besides fuel specific parameters, mainly on time but as well on the geochemical and hydraulic environment of the disposal location. The study SR 97 documents the large effort of SKB to assess the long-term performance of a repository containing spent nuclear fuel. Scenario and consequence analyses are clearly described, considering major physical and chemical interactions of the various components of the multi-barrier isolation system. The approach attempts to assess both a realistic and a pessimistic evolution scenario. The present report attempts to evaluate whether this approach is thoroughly carried through to assess the performance of spent nuclear fuel in a repository. Main issues are radionuclide inventories and inventory distribution between structural parts of the fuel assembly and the fuel matrix, potential fuel alteration prior to water access, as well as models for fuel matrix dissolution and instant release fractions. Uncertainties in radionuclide inventories are discussed and were found for many radionuclides to be higher than assumed in SR 97. This is particularly true for Cl-36. This nuclide is a potential key biosphere dose contributor in various international safety assessments. Of particular importance are uncertainties related to the partition of radionuclides between metallic parts of the fuel assembly and the fuel matrix, since inventories of metallic parts are considered to be released instantaneously. Using C-14 as an

  6. The Relative Importance of the Service Sector in the Mexican Economy: A Time Series Analysis

    Directory of Open Access Journals (Sweden)

    Carlos Alberto Flores

    2014-01-01

    Full Text Available We conduct a study of the secondary and tertiary sectors with the goal of highlighting the relative im-portance of services in the Mexican economy. We consider a time series analysis approach designed to identify the stochastic nature of the series, as well as to define their long-run and-short run relationships with Gross Domestic Product (GDP. The results of cointegration tests suggest that, for the most part, activities in the secondary and tertiary sectors share a common trend with GDP. Interestingly, the long-run elasticities of GDP with respect to services are on average larger than those with respect to secondary activities. Common cycle tests results identify the existence of common cycles between GDP and the disaggregated sectors, as well as with manufacturing, commerce, real estate and transportation. In this case, the short-run elasticities of secondary activities are on average larger than those corresponding to services.

  7. Investigation of the influence of physical and chemical properties of biodiesel in the fuel economy, energy and environmental performance of motor diesel

    Directory of Open Access Journals (Sweden)

    Korpach А.

    2016-08-01

    Full Text Available Due to exhaustion of world energy reserves and significant environmental pollution by harmful substances, current research aimed at determining the effectiveness of alternative fuels. In the article compare two samples of biodiesel and studied their physical and chemical properties accordance with International Standard. Effect of different samples of biodiesel in fuel economy, energy and environmental performance automotive diesel determined by the bench tests of 4CH11,0/12.5 (D-241 diesel. The difference between physical and chemical properties of two biodiesel samples influenced to the fuel efficiency and environmental performance of the diesel. Operation on biodiesel with higher density and kinematic viscosity provide increases of maximum power and torque and increase fuel consumption. It also increases the concentration of nitrogen oxides in exhaust gases and it opacity. The results allow evaluate how the deviation of physical and chemical properties of biodiesel could affect the operational performance of the engine.

  8. Evaporative water loss, relative water economy and evaporative partitioning of a heterothermic marsupial, the monito del monte (Dromiciops gliroides).

    Science.gov (United States)

    Withers, Philip C; Cooper, Christine E; Nespolo, Roberto F

    2012-08-15

    We examine here evaporative water loss, economy and partitioning at ambient temperatures from 14 to 33°C for the monito del monte (Dromiciops gliroides), a microbiotheriid marsupial found only in temperate rainforests of Chile. The monito's standard evaporative water loss (2.58 mg g(-1) h(-1) at 30°C) was typical for a marsupial of its body mass and phylogenetic position. Evaporative water loss was independent of air temperature below thermoneutrality, but enhanced evaporative water loss and hyperthermia were the primary thermal responses above the thermoneutral zone. Non-invasive partitioning of total evaporative water loss indicated that respiratory loss accounted for 59-77% of the total, with no change in respiratory loss with ambient temperature, but a small change in cutaneous loss below thermoneutrality and an increase in cutaneous loss in and above thermoneutrality. Relative water economy (metabolic water production/evaporative water loss) increased at low ambient temperatures, with a point of relative water economy of 15.4°C. Thermolability had little effect on relative water economy, but conferred substantial energy savings at low ambient temperatures. Torpor reduced total evaporative water loss to as little as 21% of normothermic values, but relative water economy during torpor was poor even at low ambient temperatures because of the relatively greater reduction in metabolic water production than in evaporative water loss. The poor water economy of the monito during torpor suggests that negative water balance may explain why hibernators periodically arouse to normothermia, to obtain water by drinking or via an improved water economy.

  9. On the hazard accumulation of actinide waste in a Pu-fueled LMFBR power economy with and without by-product actinide recycling

    International Nuclear Information System (INIS)

    Anselmi, L.; Caruso, K.; Hage, W.; Schmidt, E.

    1979-01-01

    The actinide waste arisings in terms of hazard potential for ingestion and inhalation are given for a Pu-fueled LMFBR Power Economy as function of decay time. The data were assessed for two simplified fuel cycles, one considering the recycling of by-product actinides and the other their complete discharge to the high-level waste. Two durations of nuclear power and several loss fractions of actinides to the waste were considered. The major contributors in form of chemical elements or isotopes to the actinide waste hazard built up during the nuclear power duration were identified for various decay intervals

  10. Queensland Alcohol-related violence and Night Time Economy Monitoring project (QUANTEM): a study protocol.

    Science.gov (United States)

    Miller, Peter G; Ferris, Jason; Coomber, Kerri; Zahnow, Renee; Carah, Nicholas; Jiang, Heng; Kypri, Kypros; Chikritzhs, Tanya; Clough, Alan; Livingston, Michael; de Andrade, Dominique; Room, Robin; Callinan, Sarah; Curtis, Ashlee; Mayshak, Richelle; Droste, Nicolas; Lloyd, Belinda; Matthews, Sharon; Taylor, Nicholas; Crane, Meredythe; Thorn, Michael; Najman, Jake

    2017-10-05

    Alcohol-related harm is a substantial burden on the community in Australia and internationally, particularly harm related to risky drinking practices of young people in the night-time economy. This protocol paper describes a study that will report on the changes in a wide range of health and justice outcome measures associated with major policy changes in the state of Queensland, Australia. A key element includes trading hours restrictions for licensed premises to 2 am for the state and 3 am in Safe Night Precincts (SNPs). Other measures introduced include drinks restrictions after midnight, increased patron banning measures for repeat offenders, mandatory ID scanning of patrons in late-night venues, and education campaigns. The primary aim of the study is to evaluate change in the levels of harm due to these policy changes using administrative data (e.g., police, hospital, ambulance, and court data). Other study elements will investigate the impact of the Policy by measuring foot traffic volume in SNPs, using ID scanner data to quantify the volume of people entering venues and measure the effectiveness of banning notices, using patron interviews to quantify the levels of pre-drinking, intoxication and illicit drug use within night-time economy districts, and to explore the impacts of the Policy on business and live music, and costs to the community. The information gathered through this project aims to evaluate the effectiveness of the Policy and to draw on these findings to inform future prevention and enforcement approaches by policy makers, police, and venue staff.

  11. Evaluating the Environmental Dimension of Material Efficiency Strategies Relating to the Circular Economy

    Directory of Open Access Journals (Sweden)

    Stuart Walker

    2018-03-01

    Full Text Available Material efficiency is a key element of new thinking to address the challenges of reducing impacts on the environment and of resource scarcity, whilst at the same time meeting service and functionality demands on materials. Directly related to material efficiency is the concept of the Circular Economy, which is based on the principle of optimising the utility embodied in materials and products through the life-cycle. Although materials such as steel, on account of high recycling rates at end-of-life, are amongst the most ‘circular’ of manufactured materials, significant opportunities for greater material efficiency exist, which are yet to be widely implemented. Life Cycle Assessment (LCA is commonly used to assess the environmental benefits of recovering and recycling materials through the manufacturing supply chain and at end-of-life. Using an example taken from renewable energy generation, this paper explores the correlation between product circularity and the environmental case for strategies designed to improve material efficiency. An LCA-based methodology for accounting for the recovery and reuse of materials from the supply chain and at end-of-life is used as the basis for calculating the carbon footprint benefits of five material efficiency scenarios. The results are compared with a number of proposed material circularity indicators. Two conclusions from this exercise are that (i LCA methodologies based around end-of-life approaches are well placed for quantifying the environmental benefits of material efficiency and circular economy strategies and (ii when applying indicators relating to the circularity of materials these should also be supported by LCA-based studies.

  12. Queensland Alcohol-related violence and Night Time Economy Monitoring project (QUANTEM: a study protocol

    Directory of Open Access Journals (Sweden)

    Peter G. Miller

    2017-10-01

    Full Text Available Abstract Background Alcohol-related harm is a substantial burden on the community in Australia and internationally, particularly harm related to risky drinking practices of young people in the night-time economy. This protocol paper describes a study that will report on the changes in a wide range of health and justice outcome measures associated with major policy changes in the state of Queensland, Australia. A key element includes trading hours restrictions for licensed premises to 2 am for the state and 3 am in Safe Night Precincts (SNPs. Other measures introduced include drinks restrictions after midnight, increased patron banning measures for repeat offenders, mandatory ID scanning of patrons in late-night venues, and education campaigns. Methods The primary aim of the study is to evaluate change in the levels of harm due to these policy changes using administrative data (e.g., police, hospital, ambulance, and court data. Other study elements will investigate the impact of the Policy by measuring foot traffic volume in SNPs, using ID scanner data to quantify the volume of people entering venues and measure the effectiveness of banning notices, using patron interviews to quantify the levels of pre-drinking, intoxication and illicit drug use within night-time economy districts, and to explore the impacts of the Policy on business and live music, and costs to the community. Discussion The information gathered through this project aims to evaluate the effectiveness of the Policy and to draw on these findings to inform future prevention and enforcement approaches by policy makers, police, and venue staff.

  13. Measurement of relative permeability of fuel cell diffusion media

    KAUST Repository

    Hussaini, I.S.; Wang, C.Y.

    2010-01-01

    Gas diffusion layer (GDL) in PEM fuel cells plays a pivotal role in water management. Modeling of liquid water transport through the GDL relies on knowledge of relative permeability functions in the in-plane and through-plane directions

  14. Phase relations, crystal structures and physical properties of nuclear fuels

    International Nuclear Information System (INIS)

    Tagawa, Hiroaki; Fujino, Takeo; Tateno, Jun

    1975-07-01

    Phase relations, crystal structures and physical properties of the compounds for nuclear fuels are presented, including melting point, thermal expansion, diffusion and magnetic and electric properties. Emphasis is on oxides, carbides and nitrides of thorium, uranium and plutonium. (auth.)

  15. Review of the IAEA Nuclear Fuel Cycle Materials Section activities related to WWER fuel

    International Nuclear Information System (INIS)

    Killeen, J.

    2003-01-01

    The IAEA Nuclear Fuel Cycle Programme, designated as Programme B, has the main objective of supporting Member States in policy making, strategic planning, developing technology and addressing issues with respect to safe, reliable, economically efficient, proliferation resistant and environmentally sound nuclear fuel cycle. This paper is concentrated on describing the work within Sub-programme B.2 'Fuel Performance and Technology'. Two Technical Working Groups assist in the preparation of the IAEA programme in the nuclear fuel cycle area - Technical Working Group on Water Reactor Fuel Performance and Technology and Technical Working Group on Nuclear Fuel Cycle Options. The activities of the Unit within the Nuclear Fuel Cycle and Materials Section working on Fuel Performance and Technology are given, based on the sub-programme structure of the Agency programme and budget for 2002-2003. Within the framework of Co-ordinated Research Projects a study of the delayed hydride cracking (DHC) of the zirconium alloys used in pressurised heavy water reactors (PHWR) involving 10 countries has been completed. It achieved very effective transfer of know-how at the laboratory level in three technologically important areas: 1) Controlled hydriding of samples to predetermined levels; 2) Accurate measurement of hydrogen concentrations at the relatively low levels found in pressure tubes and RBMK channel tubes; and 3) In the determination of DHC rates under various conditions of temperature and stress. A new project has been started on the 'Improvement of Models used for Fuel Behaviour Simulation' (FUMEX II) to assist Member States in improving the predictive capabilities of computer codes used in modelling fuel behaviour for extended burnup. The IAEA also collaborates with organisations in the Member States to support activities and meetings on nuclear fuel cycle related topics

  16. Relative efficiency of hydrogen technologies for the hydrogen economy : a fuzzy AHP/DEA hybrid model approach

    International Nuclear Information System (INIS)

    Lee, S.

    2009-01-01

    As a provider of national energy security, the Korean Institute of Energy Research is seeking to establish a long term strategic technology roadmap for a hydrogen-based economy. This paper addressed 5 criteria regarding the strategy, notably economic impact, commercial potential, inner capacity, technical spinoff, and development cost. The fuzzy AHP and DEA hybrid model were used in a two-stage multi-criteria decision making approach to evaluate the relative efficiency of hydrogen technologies for the hydrogen economy. The fuzzy analytic hierarchy process reflects the uncertainty of human thoughts with interval values instead of clear-cut numbers. It therefore allocates the relative importance of 4 criteria, notably economic impact, commercial potential, inner capacity and technical spin-off. The relative efficiency of hydrogen technologies for the hydrogen economy can be measured via data envelopment analysis. It was concluded that the scientific decision making approach can be used effectively to allocate research and development resources and activities

  17. Relative efficiency of hydrogen technologies for the hydrogen economy : a fuzzy AHP/DEA hybrid model approach

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S. [Korea Inst. of Energy Research, Daejeon (Korea, Republic of). Energy Policy Research Division; Mogi, G. [Tokyo Univ., (Japan). Dept. of Technology Management for Innovation, Graduate School of Engineering; Kim, J. [Korea Inst. of Energy Research, Daejeon (Korea, Republic of)

    2009-07-01

    As a provider of national energy security, the Korean Institute of Energy Research is seeking to establish a long term strategic technology roadmap for a hydrogen-based economy. This paper addressed 5 criteria regarding the strategy, notably economic impact, commercial potential, inner capacity, technical spinoff, and development cost. The fuzzy AHP and DEA hybrid model were used in a two-stage multi-criteria decision making approach to evaluate the relative efficiency of hydrogen technologies for the hydrogen economy. The fuzzy analytic hierarchy process reflects the uncertainty of human thoughts with interval values instead of clear-cut numbers. It therefore allocates the relative importance of 4 criteria, notably economic impact, commercial potential, inner capacity and technical spin-off. The relative efficiency of hydrogen technologies for the hydrogen economy can be measured via data envelopment analysis. It was concluded that the scientific decision making approach can be used effectively to allocate research and development resources and activities.

  18. Symptoms of another life: time, possibility, and domestic relations in Chile's credit economy.

    Science.gov (United States)

    Han, Clara

    2011-01-01

    In this article, I explore the synergy and disjunctures of the consumer credit system and care for the mentally ill and addicted in the lifeworlds of the urban poor in Santiago, Chile. In Chile, the expansion of the credit system has had a double-edged effect on the poor. Although it produces perpetual indebtedness, it also is a resource amid unstable labor. Following an extended family over several years, this article examines how women take up credit through a wider field of domestic relations and institutions to care for kin with mental illness and addiction within the home. Such gestures of care enact a temporality of waiting, allowing different, but unpredictable, aspects of others to emerge. Through longitudinal ethnographic research with this family, I demonstrate both how possibility is actualized within the home as symptoms of illness and forms of domestic violence, and how a wider network of dependencies—from neighbors to lending institutions—shapes the temporality of relations within the home. Such a study of care in relation to the credit economy may offer other analytic perspectives on discourses of individualism, consumerism, and cost-effectiveness accompanying the expansion of consumer credit as they are absorbed into the everyday.

  19. Nuclides Economy

    International Nuclear Information System (INIS)

    Ivanov, Evgeny; Subbotin, Stanislav

    2007-01-01

    Traditionally the subject of discussion about the nuclear technology development is focused on the conditions that facilitate the nuclear power deployment. The main objective of this work is seeking of methodological basis for analysis of the coupling consequences of nuclear development. Nuclide economy is the term, which defines a new kind of society relations, dependent on nuclear technology development. It is rather closed to the setting of problems then to the solving of them. Last year Dr. Jonathan Tennenbaum published in Executive Intelligence Review Vol. 33 no 40 the article entitled as 'The Isotope Economy' where main interconnections for nuclear energy technologies and their infrastructure had been explained on the popular level. There he has given several answers and, therefore, just here we will try to expand this concept. We were interested by this publication because of similarity of our vision of resource base of technologies development. The main paradigm of 'Isotope economy' was expresses by Lyndon H. LaRouche: 'Instead of viewing the relevant resources of the planet as if they were a fixed totality, we must now assume responsibility of man's creating the new resources which will be more than adequate to sustain a growing world population at a constantly improved standard of physical per-capita output, and personal consumption'. We also consider the needed resources as a dynamic category. Nuclide economy and nuclide logistics both are needed for identifying of the future development of nuclear power as far we follow the holistic analysis approach 'from cave to grave'. Thus here we try to reasoning of decision making procedures and factors required for it in frame of innovative proposals development and deployment. The nuclear power development is needed in humanitarian scientific support with maximally deep consideration of all inter-disciplinary aspects of the nuclear power and nuclear technologies implementation. The main objectives for such

  20. Evidence of fueling of the 2000 new economy bubble by foreign capital inflow: implications for the future of the US economy and its stock market

    Science.gov (United States)

    Sornette, Didier; Zhou, Wei-Xing

    2004-02-01

    Previous analyses of a large ensemble of stock markets have demonstrated that a log-periodic power law (LPPL) behavior of the prices constitutes a qualifying signature of speculative bubbles that often land with a crash. We detect such a LPPL signature in the foreign capital inflow during the bubble on the US markets culminating in March 2000. We detect a weak synchronization and lag with the NASDAQ LPPL pattern. We propose to rationalize these observations by the existence of positive feedback loops between market-appreciation/increased-spending/increased-deficit-of-balance-of-payment/larger-foreign-surplus/increased-foreign-capital-inflows and so on. Our analysis suggests that foreign capital inflow has been following rather than causing the bubble. We then combine a macroeconomic analysis of feedback processes occurring between the economy and the stock market with a technical analysis of more than 200 years of the DJIA to investigate possible scenarios for the future, three years after the end of the bubble and deep into a bearish regime. We conclude that the low interest rates and depreciating dollar are the indispensable ingredients for a lower sustainable burden of the global US debt structure and for allowing the slow rebuilding of an internationally competitive economy. This will probably be accompanied by a weak stock market on the medium term as the growing Federal deficit is consuming a large part of the foreign surplus dollars and the stock market is remaining a very risky and unattractive investment. Notwithstanding strong surge of liquidity in recent months orchestrated by the Federal Reserve, this macroeconomic analysis which incorporates an element of collective behavior is in line with our recent analyses of the bearish market that started in 2000 in terms of a LPPL “anti-bubble”. We project this LPPL anti-bubble to continue at least for another year. On the short term, increased availability of liquidity (M1) and self-fulfilling bullish

  1. A comparison of high-speed flywheels, batteries, and ultracapacitors on the bases of cost and fuel economy as the energy storage system in a fuel cell based hybrid electric vehicle

    Energy Technology Data Exchange (ETDEWEB)

    Doucette, Reed T.; McCulloch, Malcolm D. [Department of Engineering Science, University of Oxford, Thom Building, Parks Road, Oxford, OX1 3PJ (United Kingdom)

    2011-02-01

    Fuel cells aboard hybrid electric vehicles (HEVs) are often hybridized with an energy storage system (ESS). Batteries and ultracapacitors are the most common technologies used in ESSs aboard HEVs. High-speed flywheels are an emerging technology with traits that have the potential to make them competitive with more established battery and ultracapacitor technologies in certain vehicular applications. This study compares high-speed flywheels, ultracapacitors, and batteries functioning as the ESS in a fuel cell based HEV on the bases of cost and fuel economy. In this study, computer models were built to simulate the powertrain of a fuel cell based HEV where high-speed flywheels, batteries, and ultracapacitors of a range of sizes were used as the ESS. A simulated vehicle with a powertrain using each of these technologies was run over two different drive cycles in order to see how the different ESSs performed under different driving patterns. The results showed that when cost and fuel economy were both considered, high-speed flywheels were competitive with batteries and ultracapacitors. (author)

  2. Intensity related changes of running economy in recreational level distance runners.

    Science.gov (United States)

    Engeroff, Tobias; Bernardi, Andreas; Niederer, Daniel; Wilke, Jan; Vogt, Lutz; Banzer, Winfried

    2017-09-01

    Running economy (RE) is often described as a key demand of running performance. The variety of currently used assessment methods with different running intensities and outcomes restricts interindividual comparability of RE in recreational level runners. The purpose of this study was to compare the influence of RE, assessed as oxygen cost (OC) and caloric unit cost (CUC), on running speed at individual physiological thresholds. Eighteen recreational runners performed: 1) a graded exercise test to estimate first ventilatory threshold (VT1), respiratory compensation point (RCP) and maximal oxygen uptake (VO2max); 2) discontinuous RE assessment to determine relative OC in milliliters per kilogram per kilometer (mL/kg/km) and CUC in kilocalories per kilogram per kilometer (kcal/kg/km) at three different running intensities: VT1, RCP and at a third standardized reference point (TP) in between. OC (mL/kg/km; at VT1: 235.4±26.2; at TP: 227.8±23.4; at RCP: 224.9±21.9) and CUC (kcal/kg/km at VT1: 1.18±0.13; at TP: 1.14±0.12; at RCP: 1.13±0.11) decreased with increasing intensities (P≤0.01). Controlling for the influence of sex OC and CUC linearly correlated with running speed at RCP and VO2max (P≤0.01). RE, even assessed at low intensity, is strongly related to running performance in recreational athletes. Both calculation methods used (OC and CUC) are sensitive for monitoring intensity related changes of substrate utilization. RE values decreased with higher running intensity indicating an increase of anaerobic and subsequent decrease of aerobic substrate utilization.

  3. Fuels Performance | Transportation Research | NREL

    Science.gov (United States)

    chemistry, combustion, and emissions to answer two primary questions: How can improved fuel chemistry lead initiative Combustion and engines Fuel chemistry Emissions and fuel economy Find out about related NREL Chemistry. (2014) Saturated Monoglyceride Effects on Low-Temperature Performance of Biodiesel Blends. G.M

  4. WWER water chemistry related to fuel cladding behaviour

    Energy Technology Data Exchange (ETDEWEB)

    Kysela, J; Zmitko, M [Nuclear Research Inst. plc., Rez (Czech Republic); Vrtilkova, V [Nuclear Fuel Inst., Prague (Czech Republic)

    1997-02-01

    Operational experience in WWER primary water chemistry and corrosion related to the fuel cladding is reviewed. Insignificant corrosion of fuel cladding was found which is caused by good corrosion resistance of Zr1Nb material and relatively low coolant temperature at WWER-440 reactor units. The differences in water chemistry control is outlined and an attention to the question of compatibility of Zircaloys with WWER water chemistry is given. Some results of research and development in field of zirconium alloy corrosion behaviour are discussed. Experimental facility for in-pile and out-of-pile cladding material corrosion testing is shown. (author). 14 refs, 5 figs, 3 tabs.

  5. Plutonium economy

    International Nuclear Information System (INIS)

    Traube, K.

    1984-01-01

    The author expresses his opinion on the situation, describes the energy-economic setting, indicates the alternatives: fuel reprocessing or immediate long-term storage, and investigates the prospects for economic utilization of the breeder reactors. All the facts suggest that the breeder reactor will never be able to stand economic competition with light-water reactors. However, there is no way to prove the future. It is naive to think that every doubt could and must be removed before stopping the development of breeder reactors - and thus also the reprocessing of the fuel of light-water reactors. On the basis of the current state of knowledge an unbiased cost-benefit-analysis can only lead to the recommendation to stop construction immediately. But can 'experts', who for years or even decades have called for and supported the development of breeder reactors be expected to make an unbiased analysis. Klaus Traube strikes the balance of the state Germany's nuclear economy is in: although there is no chance of definitively abandoning that energy-political cul-de-sac, no new adventures must be embarked upon. Responsible handling of currently used nuclear technology means to give up breeder technology and waive plutonium economy. It is no supreme technology with the aid of which structural unemployment or any other economic problem could be solved. (orig.) [de

  6. IAEA activities related to research reactor fuel conversion and spent fuel return programs

    International Nuclear Information System (INIS)

    Goldman, Ira N.; Adelfang, Pablo; Ritchie, Iain G.

    2005-01-01

    The IAEA has been involved for more than twenty years in supporting international nuclear non-proliferation efforts associated with reducing the amount of highly enriched uranium (HEU) in international commerce. IAEA projects and activities have directly supported the Reduced Enrichment for Research and Test Reactors (RERTR) programme, as well as directly associated efforts to return research reactor fuel to the country where it was originally enriched. IAEA efforts have included the development and maintenance of several data bases with information related to research reactors and research reactor spent fuel inventories that have been essential in planning and managing both RERTR and spent fuel return programmes. Other IAEA regular budget programs have supported research reactor fuel conversion from HEU to low enriched uranium (LEU), and in addressing issues common to many member states with spent fuel management problems and concerns. The paper briefly describes IAEA involvement since the early 1980's in these areas, including regular budget and Technical Co-operation programme activities, and focuses on efforts in the past five years to continue to support and accelerate U.S. and Russian research reactor spent fuel return programmes. (author)

  7. IAEA activities related to research reactor fuel conversion and spent fuel return programmes

    International Nuclear Information System (INIS)

    Ritchie, I.G.; Adelfang, P.; Goldman, I.N.

    2004-01-01

    Full text: The IAEA has been involved for more than twenty years in supporting international nuclear non-proliferation efforts associated with reducing the amount of highly enriched uranium (HEU) in international commerce. IAEA projects and activities have directly supported the Reduced Enrichment for Research and Test Reactors (RERTR) programme, as well as directly associated efforts to return research reactor fuel to the country of origin where it was originally enriched. IAEA efforts have included the development and maintenance of several data bases with information related to research reactors and research reactor spent fuel inventories that have been essential in planning and managing both RERTR and spent fuel return programmes. Other IAEA regular budget programmes have supported research reactor fuel conversion from HEU to low enriched uranium, and in addressing issues common to many member states with spent fuel management problems and concerns. The paper briefly describes IAEA involvement since the early 1980's in these areas, including regular budget and Technical Co-operation programme activities, and focuses on efforts in the past five years to continue to support and accelerate U.S. and Russian research reactor spent fuel return programmes. It is hoped that an announcement of the extension of the U.S. Acceptance Programme, which is expected in the very near future, will facilitate the life extensions of many productive TRIGA reactors around the world. (author)

  8. Real economy versus virtual economy - New challenges for nowadays society

    Directory of Open Access Journals (Sweden)

    Associates Professon Dr. Veronica Adriana Popescu

    2011-05-01

    Full Text Available In the paper Real Economy versus Virtual Economy – New Challenges for Nowadays Society our goal is to present the importance of both real economy and virtual economy.At the begging of our research, we have presented the main views of some specialists concerning both virtual and real economy. After that we have compared the two types of economies and we have stressed the most important aspects connected to them. The main reason why we have decided to approach this complex subject is due to the increasing interest in the virtual economy matters and the relation that this particular type of economy develops with the real economy.

  9. THE IMPACT OF VAT ON THE ECONOMY IN RELATION TO OTHER TAXES IN SOUTH EAST EUROPE

    Directory of Open Access Journals (Sweden)

    Petre BREZEANU

    2018-06-01

    Full Text Available Through this article, we aim to create a multifactorial model of linear regression by which we discover the impact of the most important taxes in an economy in the economies of the countries of Southeastern Europe. We have selected South East Europe to include and Romania in the empirical analysis. So for building the model, we considered it opportune to choose the following independent variables: VAT, Excise, Income Tax. The economy as a whole was considered to be well defined by the Gross Domestic Product it produces, which is why GDP has been selected as a variable. The chosen period spans a sample of 20 years. In conclusion, this study will try to highlight how fiscal pillars, such as VAT, ACIs and income taxes, affect the GDP. In the light of the results obtained, we will try to interpret the coefficients obtained through a fiscal policy that is dominant or not at this level.

  10. Research on the Impacts of Expensive Food and Luxury Goods Import Tariff Adjustment on Chinese Economy and Related Measures

    OpenAIRE

    Qishen Zhou; Mingxing Yang

    2013-01-01

    This study aims to investigate the impacts of expensive food and luxury goods import tariff adjustment on Chinese economy and related measures. Nowadays, Asia especially China has been the world’s biggest expensive food and luxury goods market. However, due to relatively higher luxury import tariff in China, most consumers have chosen to purchase expensive food and luxury goods abroad which leads to a large of domestic consumption cash outflow. Therefore, whether to cut the luxury import tari...

  11. Assessment of Used Nuclear Fuel Inventory Relative to Disposition Options

    International Nuclear Information System (INIS)

    Wagner, John C.; Peterson, Joshua L.; Mueller, Don; Gehin, Jess C.; Worrall, Andrew; Taiwo, Temitope; Nutt, Mark; Williamson, Mark A.; Todosow, Mike; Wigeland, Roald; Halsey, William; Omberg, Ronald; Swift, Peter; Carter, Joe

    2013-01-01

    This paper presents a technical assessment of the current inventory [∼70,150 metric tons of heavy metal (MTHM) as of 2011] of U.S.-discharged used nuclear fuel (UNF) to support decisions regarding fuel cycle strategies and research, development and demonstration (RD and D) needs. The assessment considered discharged UNF from commercial nuclear electricity generation and defense and research programs and determined that the current UNF inventory can be divided into the following three categories: 1. Disposal - excess material that is not needed for other purposes; 2. Research - material needed for RD and D purposes to support waste management (e.g., UNF storage, transportation, and disposal) and development of alternative fuel cycles (e.g., separations and advanced fuels/reactors); and 3. Recycle/Recovery - material with inherent and/or strategic value. A set of key assumptions and attributes relative to the disposition options was used to categorize the current UNF inventory. Based on consideration of RD and D needs, time frames and material needs for deployment of alternative fuel cycles, characteristics of the current UNF inventory, and possible uses to support national security interests, it was determined that the vast majority of the category, without the need for retrieval for reuse or research purposes. Access to the material in the Research and Recycle/Recovery categories should be retained to support RD and D needs and national security interests. This assessment does not assume any decision about future fuel cycle options or preclude any potential options, including those with potential recycling of commercial UNF, since the ∼2,000 MTHM that is generated annually could provide the feedstock needed for deployment of alternative fuel cycles.

  12. The Sharing Economy

    OpenAIRE

    Reinhold, Stephan; Dolnicar, Sara

    2017-01-01

    Peer-to-peer accommodation networks in general, and Airbnb in specific, are frequently referred to as part of the sharing economy. This chapter provides an overview of key characteristics of the sharing economy, discusses how these characteristics relate to peer-to-peer accommodation, and positions peer-to-peer accommodation networks within the sharing economy.

  13. Issues related to EM management of DOE spent nuclear fuel

    International Nuclear Information System (INIS)

    Abbott, D.G.; Abashian, M.S.; Chakraborti, S.; Roberson, K.; Meloin, J.M.

    1993-07-01

    This document is a summary of the important issues involved in managing spent nuclear fuel (SNF) owned by the Department of Energy (DOE). Issues related to civilian SNF activities are not discussed. DOE-owned SNF is stored primarily at the Hanford Site, Idaho National Engineering Laboratory (INEL), Savannah River Site (SRS), Oak Ridge National Laboratory (ORNL), and West Valley Demonstration Project. Smaller quantities of SNF are stored at Brookhaven National Laboratory, Sandia National Laboratories, and Los Alamos National Laboratory (LANL). There is a wide variety of fuel types, including both low and high enrichment fuels from weapons production, DOE reactors, research and development programs, naval programs, and universities. Most fuel is stored in pools associated with reactor or reprocessing facilities. Smaller quantities are in dry storage. Physical conditions of the fuel range from excellent to poor or severely damaged. An issue is defined as an important question that must be answered or decision that must be made on a topic or subject relevant to achieving the complimentary objectives of (a) storing SNF in compliance with applicable regulations and orders until it can be disposed, and (b) safely disposing of DOE's SNF. The purpose of this document is to define the issues; no recommendations are made on resolutions. As DOE's national SNF management program is implemented, a system of issues identification, documentation, tracking, and resolution will be implemented. This document is an initial effort at issues identification. The first section of this document is an overview of issues that are common to several or all DOE facilities that manage SNF. The common issues are organized according to specific aspects of spent fuel management. This is followed by discussions of management issues that apply specifically to individual DOE facilities. The last section provides literature references

  14. Evironmental assessment factors relating to reprocessing of spent nuclear fuel

    International Nuclear Information System (INIS)

    1978-05-01

    This document is in two parts. Part I presents the criteria and evaluation factors, based primarily on US experience, which may be used to carry out an environmental assessment of spent fuel reprocessing. The concept of As Low as is Reasonably Achievable (ALARA) is introduced in limiting radiation exposure. The factors influencing both occupational and general public radiation exposure are reviewed. Part II provides information on occupational and general public radiation exposure in relation to reprocessing taken from various sources including UNSCEAR and GESMO. Some information is provided in relation to potential accidents at reprocessing or MOX fuel refabrication plants. The magnitude of the services, energy, land use and non-radiological effluents for the reference design of reprocessing plant are also presented

  15. Management of severely damaged nuclear fuel and related waste

    International Nuclear Information System (INIS)

    1991-01-01

    This report is concerned primarily with severe fuel damage accidents in large electric power producing reactors such as those in the TMI and Chernobyl plants. It does include, as appropriate, knowledge gained from accidents in other power, research and military reactors. It is believed that the conclusions and recommendations apply to a large extent to severe fuel damage accidents in all types of reactors. The period considered in this publication begins after the initial crisis of an accident has been brought under control. (This initial crisis could be from one day to several weeks after the event, depending on the specific conditions). Accordingly, it is assumed that the plant is shut down, the reactor is under control and decay heat removal is in progress in a stable manner so that attention must be given to cleanup. This report addresses the principles involved in planning, engineering, construction, operation and other activities to characterize, clean up and dispose of the fuel and related waste. The end of the period under consideration is when the fuel and abnormal wastes are packaged either for interim storage or final disposal and activities are started either to restore the plant to service or to establish a safe state from which decommissioning planning can start. 36 refs, 3 figs, 4 tabs.

  16. Graphite behaviour in relation to the fuel element design

    Energy Technology Data Exchange (ETDEWEB)

    Everett, M. R. [OECD High Temperature Reactor Project Dragon, Winfrith (United Kingdom); Manzel, R. [OECD High Temperature Reactor Project Dragon, Winfrith (United Kingdom); Blackstone, R. [Reactor Centrum, Petten (Netherlands); Delle, W. [Kernforschungsanlage, Juelich (Germany); Lungagnani, V. [Joint Nuclear Research Centre, Euratom, Petten (Netherlands); Krefeld, R. [Joint Nuclear Research Centre, Euratom, Petten (Netherlands)

    1969-09-01

    The first designs of H.T.R. power reactors will probably use a Gilsocarbon based graphite for both the moderator/carrier blocks and for the fuel tubes. The initial physical properties and changes of dimensions, thermal expansion coefficient, Young*s modulus, and thermal conductivity on irradiation of Gilsocarbon graphites to typical reactor dwell-time fast neutron doses of 4 * 1021 cm -2 Ni dose Dido equivalent are given and values for the irradiation creep constant are presented. The influence of these property changes and those of chemical corrosion are considered briefly in relation to the present fuel element designs. The selection of an eventual less costly replacement graphite for Gilsocarbon graphite is discussed in terms of materials properties.

  17. Operational limitations of light water reactors relating to fuel performance

    International Nuclear Information System (INIS)

    Cheng, H.S.

    1976-07-01

    General aspects of fuel performance for typical Boiling and Pressurized Water Reactors are presented. Emphasis is placed on fuel failures in order to make clear important operational limitations. A discussion of fuel element designs is first given to provide the background information for the subsequent discussion of several fuel failure modes that have been identified. Fuel failure experiences through December 31, 1974, are summarized. The operational limitations that are required to mitigate the effects of fuel failures are discussed

  18. Food Desertification: Situating Choice and Class Relations within an Urban Political Economy of Declining Food Access

    Directory of Open Access Journals (Sweden)

    Melanie Bedore

    2014-05-01

    Full Text Available While food deserts create whole sets of tangible consequences for people living within them, the problem has yet to be the subject of much normative, in-depth evaluation as an urban political economy of food access. This paper provides a critical analysis of a specific food desert and its responses, drawing on a case study of the low-income, spatially segregated North End of the small city of Kingston, Ontario, Canada. The main thrust of the paper is that the food desert remains a useful yet underexplored phenomenon through which to reveal the complexities and tensions surrounding the treatment of “choice” in a classed society. Understood as an urban political economy of declining food access, the food desert phenomenon reveals capital’s complex role in the promotion or violation of dignity through the urban geographies of acquiring food for oneself, family, or household. Through the data presented here, the article also argues for a collective pause among critical scholars to radicalize, rather than reject, the role of consumer choice in a more just food system, and for further normative engagement with urban landscapes of retail consolidation.

  19. About Economy of Fuel at Thermal Power Stations due to Optimization of Utilization Diagram of Power-Generating Equipment

    Directory of Open Access Journals (Sweden)

    M. V. Svechko

    2008-01-01

    Full Text Available Problems of rational fuel utilization becomes more and more significant especially for thermal power stations (TPS. Thermal power stations have complicated starting-up diagrams and utilization modes of their technological equipment. Method of diagram optimization of TPS equipment utilization modes has been developed. The method is based on computer analytical model with application of spline-approximation of power equipment characteristics. The method allows to economize fuel consumption at a rate of 15-20 % with accuracy of the predicted calculation not more than 0.25 %.

  20. Political economy of low sulfurization and air pollution control policy in Japan : SOx emission reduction by fuel conversion

    OpenAIRE

    Terao, Tadayoshi

    2013-01-01

    In the early stages of the development of Japan’s environmental policy, sulfur oxide (SOx) emissions, which seriously damage health, was the most important air pollution problem. In the second half of the 1960s and the first half of the 1970s, the measures against SOx emissions progressed quickly, and these emissions were reduced drastically. The most important factor of the reduction was the conversion to a low-sulfur fuel for large-scale fuel users, such as the electric power industry. Howe...

  1. Measurement of relative permeability of fuel cell diffusion media

    KAUST Repository

    Hussaini, I.S.

    2010-06-01

    Gas diffusion layer (GDL) in PEM fuel cells plays a pivotal role in water management. Modeling of liquid water transport through the GDL relies on knowledge of relative permeability functions in the in-plane and through-plane directions. In the present work, air and water relative permeabilities are experimentally determined as functions of saturation for typical GDL materials such as Toray-060, -090, -120 carbon paper and E-Tek carbon cloth materials in their plain, untreated forms. Saturation is measured using an ex situ gravimetric method. Absolute and relative permeability functions in the two directions of interest are presented and new correlations for in-plane relative permeability of water and air are established. © 2010 Elsevier B.V. All rights reserved.

  2. Collaborative Economy

    DEFF Research Database (Denmark)

    collaborative economy and tourism Dianne Dredge and Szilvia Gyimóthy PART I - Theoretical explorations 2.Definitions and mapping the landscape in the collaborative economy Szilvia Gyimóthy and Dianne Dredge 3.Business models of the collaborative economy Szilvia Gyimóthy 4.Responsibility and care...... in the collaborative economy Dianne Dredge 5.Networked cultures in the collaborative economy Szilvia Gyimóthy 6.Policy and regulatory perspectives in the collaborative economy Dianne Dredge PART II - Disruptions, innovations and transformations 7.Regulating innovation in the collaborative economy: An examination...... localities of tourism Greg Richards 11.Collaborative economy and destination marketing organizations: A systems approach Jonathan Day 12.Working within the Collaborative Tourist Economy: The complex crafting of work and meaning Jane Widtfeldt Meged and Mathilde Dissing Christensen PART - III Encounters...

  3. Comments on the Joint Proposed Rulemaking to Establish Light-Duty Vehicle Greenhouse Gas Emission Standards and Corporate Average Fuel Economy Standards

    Energy Technology Data Exchange (ETDEWEB)

    Wenzel, Thomas P

    2009-10-27

    I appreciate the opportunity to provide comments on the joint rulemaking to establish greenhouse gas emission and fuel economy standards for light-duty vehicles. My comments are directed at the choice of vehicle footprint as the attribute by which to vary fuel economy and greenhouse gas emission standards, in the interest of protecting vehicle occupants from death or serious injury. I have made several of these points before when commenting on previous NHTSA rulemakings regarding CAFE standards and safety. The comments today are mine alone, and do not necessarily represent the views of the US Department of Energy, Lawrence Berkeley National Laboratory, or the University of California. My comments can be summarized as follows: (1) My updated analysis of casualty risk finds that, after accounting for drivers and crash location, there is a wide range in casualty risk for vehicles with the same weight or footprint. This suggests that reducing vehicle weight or footprint will not necessarily result in increased fatalities or serious injuries. (2) Indeed, the recent safety record of crossover SUVs indicates that weight reduction in this class of vehicles resulted in a reduction in fatality risks. (3) Computer crash simulations can pinpoint the effect of specific design changes on vehicle safety; these analyses are preferable to regression analyses, which rely on historical vehicle designs, and cannot fully isolate the effect of specific design changes, such as weight reduction, on crash outcomes. (4) There is evidence that automakers planned to build more large light trucks in response to the footprint-based light truck CAFE standards. Such an increase in the number of large light trucks on the road may decrease, rather than increase, overall safety.

  4. Symposium on hydrogen technology and fuel cells - opportunities for the economy; Symposium Wassertechnologie und Brennstoffzellen - Chancen fuer die Wirtschaft

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-07-01

    This volume contains 17 contributions on fuel cell technology and on the infrastructure required for hydrogen production and supply, in the form of abstracts and short reports. [German] Dieser Band enthaelt 17 Beitraege zum Themenkreis Brennstoffzellentechnologie und die dazu erforderliche Infrastruktur fuer die Wasserstofferzeugung und -versorgung in Form von Kurzfassungen und Vortragsfolien.

  5. Fuel cracking in relation to fuel oxidation in support of an out-reactor instrumented defected fuel experiment

    Energy Technology Data Exchange (ETDEWEB)

    Quastel, A.; Thiriet, C. [Atomic Energy of Canada Limited, Chalk River, ON (Canada); Lewis, B., E-mail: brent.lewis@uoit.ca [Univ. of Ontario Inst. of Tech., Oshawa, ON (Canada); Corcoran, E., E-mail: emily.corcoran@rmc.ca [Royal Military College of Canada, Kingston, ON (Canada)

    2014-07-01

    An experimental program funded by the CANDU Owners Group (COG) is studying an out-reactor instrumented defected fuel experiment in Stern Laboratories (Hamilton, Ontario) with guidance from Atomic Energy of Canada Limited (AECL). The objective of this test is to provide experimental data for validation of a mechanistic fuel oxidation model. In this experiment a defected fuel element with UO{sub 2} pellets will be internally heated with an electrical heater element, causing the fuel to crack. By defecting the sheath in-situ the fuel will be exposed to light water coolant near normal reactor operating conditions (pressure 10 MPa and temperature 265-310{sup o}C) causing fuel oxidation, especially near the hotter regions of the fuel in the cracks. The fuel thermal conductivity will change, resulting in a change in the temperature distribution of the fuel element. This paper provides 2D r-θ plane strain solid mechanics models to simulate fuel thermal expansion, where conditions for fuel crack propagation are investigated with the thermal J integral to predict fuel crack stress intensity factors. Finally since fuel crack geometry can affect fuel oxidation this paper shows that the solid mechanics model with pre-set radial cracks can be coupled to a 2D r-θ fuel oxidation model. (author)

  6. ORNL-GM: Development of Ionic Liquid-Additized, GF-5/6 Compatible Low-Viscosity Oils for Automotive Engine and Rear Axle Lubrication for 4% Improved Fuel Economy

    Energy Technology Data Exchange (ETDEWEB)

    Qu, Jun [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Zhou, Yan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Luo, Huimin [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Toops, Todd J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Brookshear, Daniel W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Stump, Benjamin C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Viola, Michael B. [General Motors (GM) Technical Center, Pontiac, MI (United States); Zreik, Khaled [General Motors (GM) Technical Center, Pontiac, MI (United States); Ahmed, Tasfia [General Motors (GM) Technical Center, Pontiac, MI (United States)

    2017-01-01

    The overall objective of this project are as follows: Further develop ionic liquid (IL)-additized lowviscosity engine oils meeting the GF-5/6 specifications and possessing superior lubricating characteristics; Expand the IL additive technology to rear axle lubricants; and Seek a combined improvement in the vehicle fuel economy

  7. Impact on vehicle fuel economy of the soot loading on diesel particulate filters made of different substrate materials

    International Nuclear Information System (INIS)

    Millo, Federico; Andreata, Maurizio; Rafigh, Mahsa; Mercuri, Davide; Pozzi, Chiara

    2015-01-01

    Wall flow DPFs (Diesel Particulate Filters) are nowadays universally adopted for all European passenger cars. Since the properties of the filter substrate material play a fundamental role in determining the optimal soot loading level to be reached before DPF regeneration, three different filter material substrates (Silicon Carbide, Aluminum Titanate and Cordierite) were investigated in this work, considering different driving conditions, after treatment layouts and regeneration strategies. In the first step of the research, an experimental investigation on the three different substrates over the NEDC (New European Driving Cycle) was performed. The data obtained from experiments were then used for the calibration and the validation of a one dimensional fluid-dynamic engine and after treatment simulation model. Afterward, the model was used to predict the vehicle fuel consumption increments as a function of the exhaust back pressure due to the soot loading for different driving cycles. The results showed that appreciable fuel consumption increments could be noticed only in particular driving conditions, and, as a consequence, in most of the cases the optimal filter regeneration strategy corresponds to reach the highest soot loading that still ensures the component safety even in case of uncontrolled regeneration events. - Highlights: • Three different substrate materials for a Diesel Particulate Filter were investigated. • Fuel consumption increases due to DPF soot loading were generally not appreciable. • Optimal soot loading before regeneration was the highest safeguarding DPF integrity. • SiC substrate showed highest soot load limit and lowest fuel consumption penalties. • AT and Cd substrate properties lead to lower soot load limits than SiC

  8. Increased fuel economy in transportation systems by use of energy management. Third year's program. Final report, May 1, 1976--July 1, 1976

    Energy Technology Data Exchange (ETDEWEB)

    Beachley, N.H.; Frank, A.A.

    1976-07-01

    A report is given of the results accomplished during the third year of a three-year research program, the overall goal of which has been to conceive and evaluate practical ways to increase automobile fuel economy by energy management within the engine-transmission-vehicle system. The third year was devoted primarily to the detailed design, construction, and preliminary evaluation of a Flywheel Energy Management Powerplant (FEMP) installed in a Pinto. The vehicle has been built to experimentally verify performance simulations and to allow the practical aspects of a real flywheel vehicle to be studied. The FEMP consists basically of an internal combustion engine, a high-speed energy-storage flywheel, and a hydrostatic power-split continuously-variable transmission (CVT) system. The flywheel drives the car, and the engine comes on to ''recharge'' it (with efficient wide-open throttle operation) only when the flywheel speed drops below a predetermined value. The concept also permits effective and efficient regenerative braking. Computer simulations have indicated an improvement in city fuel mileage of about 50%, with improvements of 100% appearing feasible with further research. Preliminary testing of the car shows favorable performance.

  9. Bike Sharing and the Economy, the Environment, and Health-Related Externalities

    Directory of Open Access Journals (Sweden)

    Lu-Yi Qiu

    2018-04-01

    Full Text Available In recent years, bike-sharing has experienced rapid development; however, controversies about the externalities of bike-sharing programs have arisen as well. While bike-sharing programs have impacts on traffic, the environment, and public health, the social impacts, the management, and sustainable development of bike-sharing has also been of interest. The debate regards whether there are externalities, as well as whether and how such externalities can be determined. Based on the rapidly diffused bike-sharing in China, this paper quantitatively explores bike-sharing externalities. Specifically, this paper estimates the impacts of bike-sharing on the economy, energy use, the environment, and public health. The empirical results show that bike-sharing programs have significant positive externalities. The bike-sharing systems can provide urban residents with a convenient and time-saving travel mode. We find that the bike-sharing dramatically decreases traffic, reduces energy consumption, decreasing harmful gas emissions, improves public health generally, and promotes economic growth. This study contributes to a better comprehension of the externalities of bike-sharing and provides empirical evidence of the impacts of bike-sharing. Findings suggest that bike-sharing can play a critical role in the process of urban transportation development and provide information useful for urban transportation policies.

  10. The political economy of urban homicide: assessing the relative impact of gender inequality on sex-specific victimization.

    Science.gov (United States)

    DeWees, Mari A; Parker, Karen F

    2003-02-01

    This research examines the ways in which the changing political economy of urban areas has contributed differently to the homicide victimization rates of females and males across US cities. Recent research, while relatively limited, has presented disparate results regarding the effect of gender inequality on urban sex-specific victimization. Our work further explores this relationship by taking into account relative gender disparities in income, education, labor market opportunities, and politics in an examination of sex-specific homicide victimization in 1990. Key to this current investigation is the evaluation of feminist and lifestyle arguments that suggest that structural gender inequality has a unique effect on female victimization. Overall, our findings reveal gender inequality to be a significant predictor of both male and female urban homicide. While these findings suggest mixed support for theoretical arguments regarding gender inequality, further analyses reveal significant differences in specific types of gender inequality on victimization patterns across genders. These additional results highlight the need for greater attention toward both methodological and theoretical issues when examining the interconnections between gender, political economy, and violence in research.

  11. The effects of the final disposal facility for spent nuclear fuel on regional economy; Kaeytetyn ydinpolttoaineen loppusijoituslaitoksen aluetaloudelliset vaikutukset

    Energy Technology Data Exchange (ETDEWEB)

    Laakso, S. [Seppo Laakso Urban Research (Finland)

    1999-03-01

    The study deals with the economic effects of the final disposal facility for spent nuclear fuel on the alternative location municipalities - Eurajoki, Kuhmo, Loviisa and Aeaenekoski - and their neighbouring areas (in Finland). The economic influence of the facility on industrials, employment, population, property markets, community structure and local public economics are analysed applying the approach of regional economics. The evaluation of the facility`s effects on employment is based on the input-output analysis. Both the direct and indirect effects of the construction and the functioning of the facility are taken into account in the analysis. According to the results the total increase in employment caused by the construction of the facility is about 350 persons annually, at national level. Some 150 persons of this are estimated to live in the wider region and 100-150 persons in the facility`s influence area consisting of the location municipality and neighbouring municipalities. This amount is reached at the top stage of construction (around the year 2018). At the production stage - after the year 2020 - the facility`s effects on employment will be concentrated significantly more on the location municipality and the rest of the influence area than on the rest of the country, compared with the construction stage. The estimated employment growth in the production stage is approximately 160 persons at national level of which 100-120 persons live in the candidate municipality and in the rest of the influence area. There is a direct link between local employment and population development. The growth of jobs attracts immigrants affecting the development of both the number and the structure of population. The facility`s effects on population development in the alternative location municipalities are analysed using comparative population forecasts based on demographic population projection methods. According to the results the job growth caused by the facility will

  12. Fuel handling, reprocessing, and waste and related nuclear data aspects

    International Nuclear Information System (INIS)

    Kuesters, H.; Lalovic, M.; Wiese, H.W.

    1979-06-01

    The essential processes in the out-of-pile nuclear fuel cycle are described, i.e. mining and milling of uranium ores, enrichment, fuel fabrication, storage, transportation, reprocessing of irradiated fuel, waste treatment and waste disposal. The aspects of radiation (mainly gammas and neutrons) and of heat production, as well as special safety considerations are outlined with respect to their potential operational impacts and long-term hazards. In this context the importance of nuclear data for the out-of-pile fuel cycle is discussed. Special weight is given to the LWR fuel cycle including recycling; the differences of LMFBR high burn-up fuel with large PuO 2 content are described. The HTR fuel cycle is discussed briefly as well as some alternative fuel cycle concepts. (orig.) [de

  13. Japan's plutonium economy

    International Nuclear Information System (INIS)

    Hecht, M.M.

    1994-01-01

    Japan's plutonium economy is based on the most efficient use of nuclear energy, as envisioned under the Atoms for Peace program of the 1950s and 1960s. The nuclear pioneers assumed that all nations would want to take full advantage of atomic energy, recycling waste into new fuel to derive as much energy as possible from this resource

  14. Collaborative Economy

    DEFF Research Database (Denmark)

    that are emerging from them, and how governments are responding to these new challenges. In doing so, the book provides both theoretical and practical insights into the future of tourism in a world that is, paradoxically, becoming both increasingly collaborative and individualized. Table of Contents Preface 1.The...... collaborative economy and tourism Dianne Dredge and Szilvia Gyimóthy PART I - Theoretical explorations 2.Definitions and mapping the landscape in the collaborative economy Szilvia Gyimóthy and Dianne Dredge 3.Business models of the collaborative economy Szilvia Gyimóthy 4.Responsibility and care...... in the collaborative economy Dianne Dredge 5.Networked cultures in the collaborative economy Szilvia Gyimóthy 6.Policy and regulatory perspectives in the collaborative economy Dianne Dredge PART II - Disruptions, innovations and transformations 7.Regulating innovation in the collaborative economy: An examination...

  15. Collaborative Economy

    DEFF Research Database (Denmark)

    collaborative economy and tourism Dianne Dredge and Szilvia Gyimóthy PART I - Theoretical explorations 2.Definitions and mapping the landscape in the collaborative economy Szilvia Gyimóthy and Dianne Dredge 3.Business models of the collaborative economy Szilvia Gyimóthy 4.Responsibility and care...... and similar phenomena are among these collective innovations in tourism that are shaking the very bedrock of an industrial system that has been traditionally sustained along commercial value chains. To date there has been very little investigation of these trends, which have been inspired by, amongst other...... in the collaborative economy Dianne Dredge 5.Networked cultures in the collaborative economy Szilvia Gyimóthy 6.Policy and regulatory perspectives in the collaborative economy Dianne Dredge PART II - Disruptions, innovations and transformations 7.Regulating innovation in the collaborative economy: An examination...

  16. FROM CIRCULAR ECONOMY TO BLUE ECONOMY

    Directory of Open Access Journals (Sweden)

    Iustin-Emanuel, ALEXANDRU

    2014-11-01

    Full Text Available Addressing the subject of this essay is based on the background ideas generated by a new branch of science - Biomimicry. According to European Commissioner for the Environment, "Nature is the perfect model of circular economy". Therefore, by imitating nature, we are witnessing a process of cycle redesign: production-consumption-recycling. The authors present some reflections on the European Commission's decision to adopt after July 1, 2014 new measures concerning the development of more circular economies. Starting from the principles of Ecolonomy, which is based on the whole living paradigm, this paper argues for the development within each economy of entrepreneurial policies related to the Blue economy. In its turn, Blue economy is based on scientific analyses that identify the best solutions in a business. Thus, formation of social capital will lead to healthier and cheaper products, which will stimulate entrepreneurship. Blue economy is another way of thinking economic practice and is a new model of business design. It is a healthy, sustainable business, designed for people. In fact, it is the core of the whole living paradigm through which, towards 2020, circular economy will grow more and more.

  17. The relative labour productivity contribution of different age-skill categories for a developing economy

    Directory of Open Access Journals (Sweden)

    Gerhardus van Zyl

    2013-01-01

    Full Text Available Orientation: The article dealt with the estimation, computation and interpretation of the relative productivity contributions of different age-skill categories. Research purpose: The aim of the article was to estimate and compute, (1 relative productivity contributions and (2 relative productivity contribution–employee remuneration cost levels for different age-skill categories. Motivation for the study: The research was deemed necessary given the current debate on relative productivity levels and possible changes to the retirement age in the South African labour market. No real research in this regard has been published regarding the South African labour market situation. Research design, approach and method: A less restrictive production function was used, allowing for the simultaneous estimation and final computation of relative labour contribution levels of different age-skill categories. Main findings: The lower-skilled segment produced significantly smaller productivity contributions and the relative productivity contribution–employee remuneration cost ratios of the 55 years and older age group were superior in the higher-skilled segment but, at the same time, the lowest in the lower-skilled segment. Practical/managerial implications: It is recommended that human resource practitioners (given the perceived rigidity of labour legislation implement and maintain structures that promote higher productivity levels for all age-skill categories in the workplace. Contribution/value-add: An estimation procedure, which can be applied to the measurement of the relative productivity contribution of different age-skill categories, has been established.

  18. The relative labour productivity contribution of different age-skill categories for a developing economy

    Directory of Open Access Journals (Sweden)

    Gerhardus van Zyl

    2013-01-01

    Full Text Available Orientation: The article dealt with the estimation, computation and interpretation of the relative productivity contributions of different age-skill categories.Research purpose: The aim of the article was to estimate and compute, (1 relative productivity contributions and (2 relative productivity contribution–employee remuneration cost levels for different age-skill categories.Motivation for the study: The research was deemed necessary given the current debate on relative productivity levels and possible changes to the retirement age in the South African labour market. No real research in this regard has been published regarding the South African labour market situation.Research design, approach and method: A less restrictive production function was used, allowing for the simultaneous estimation and final computation of relative labour contribution levels of different age-skill categories.Main findings: The lower-skilled segment produced significantly smaller productivity contributions and the relative productivity contribution–employee remuneration cost ratios of the 55 years and older age group were superior in the higher-skilled segment but, at the same time, the lowest in the lower-skilled segment.Practical/managerial implications: It is recommended that human resource practitioners (given the perceived rigidity of labour legislation implement and maintain structures that promote higher productivity levels for all age-skill categories in the workplace.Contribution/value-add: An estimation procedure, which can be applied to the measurement of the relative productivity contribution of different age-skill categories, has been established.

  19. System failure, innovation policy and patents: Fuel cells and related hydrogen technology in Norway 1990-2002

    International Nuclear Information System (INIS)

    Godoe, Helge; Nygaard, Stian

    2006-01-01

    The empirical focus of this article is technological innovation activities in the emerging field of fuel cells and related hydrogen technology in Norway from 1990 to 2002. In this period, four comparatively large-scale research and development projects and a number of smaller projects aimed at development of fuel cells technology were undertaken, resulting in many inventions that were subsequently patented. Although this creativity may be considered an indication of success, only one of the projects became successful in an innovation perspective. All the large projects were initiated and funded for divergent political and economic reasons. An important reason in the late 1980s was the prospect of using Norway's abundant supply of natural gas in fuel cells for electric power generation. The large R and D projects that attempted to develop fuel cells based on natural gas as energy source failed. In contrast, the successful project was undertaken by military R and D, i.e. in a different system of innovation than the projects that failed. Analysis of these cases points to the importance of a systemic approach to innovations-and to policy making. One challenge for policy makers is to decide how they should promote this development which is crucial for the vision of a future 'Hydrogen Economy', i.e. what kind of policy incentives should be introduced to spur efficiency in technological development and diffusion. Theoretically, many options are available; however, understanding the innovation dynamics in this sector is fundamental for making choices. In this article, focus will be set on policy aspects using an innovation systemic approach to analyze development of fuel cells and related hydrogen technology in Norway

  20. THE OUTSET AND DEVELOPMENT OF PUBLIC RELATIONS (PR) IN ROMANIAN ECONOMY AFTER 1990

    OpenAIRE

    Raluca ZOLTAN; Ghiorghi PRISACARU; Romulus VANCEA

    2009-01-01

    Currently, even in Romania the public relations (PR) develops in extremely diverse organizations, have varied frames of work and implies objectives sometimes hard to conciliate; they are practiced in and for governmental institutions, also in / for non-governmental organizations, for companies which pursue the profit, but also for civic associations, for banks, for educational or cultural institutions. The objectives of public relations are different too: from inducement of the public in favo...

  1. The ring of fire: the relative importance of fuel packing versus intrinsic leaf flammability

    NARCIS (Netherlands)

    Grootemaat, S.; Wright, I.J.; Cornelissen, J.H.C.; Viegas, D.X.

    2014-01-01

    Two different experimental set-ups were used to disentangle the relative importance of intrinsic leaf traits versus fuel packing for the flammability in fuel beds. Dried leaves from 25 Australian perennial species were burnt in fuel bed rings under controlled conditions. The flammability parameters

  2. Safety aspects related to burnup increase and mixed oxide fuel

    International Nuclear Information System (INIS)

    Thomas, W.

    1992-01-01

    The dominant factor presently limiting the fuel burnup is the response of the cladding hulls. To maintain the excellent record of very low fuel failure rates for increased burnups further technical development is underway and necessary. In the nuclear fuel cycle increased burnups lead to a remarkable reduction of spent fuel arisings and corresponding economic savings. Thermal recycling of plutonium presently provides an opportunity to reduce the rising accumulation of plutunium in a situation where there is no demand for this fissile material in Fast Breeder Reactors. (orig.) [de

  3. Knowledge Economy

    OpenAIRE

    Kerr, Aphra; O Riain, Sean

    2009-01-01

    We examine a number of key questions regarding this knowledge economy. First, we look at the origin of the concept as well as early attempts to define and map the knowledge economy empirically. Second, we examine a variety of perspectives on the socio-spatial organisation of the knowledge economy and approaches which link techno-economic change and social-spatial organisation. Building on a critique of these perspectives, we then go on to develop a view of a knowledge economy that is conteste...

  4. Fuel cycle related parametric study considering long lived actinide production, decay heat and fuel cycle performances

    International Nuclear Information System (INIS)

    Raepsaet, X.; Damian, F.; Lenain, R.; Lecomte, M.

    2001-01-01

    One of the very attractive HTGR reactor characteristics is its highly versatile and flexible core that can fulfil a wide range of diverse fuel cycles. Based on a GTMHR-600 MWth reactor, analyses of several fuel cycles were carried out without taking into account common fuel particle performance limits (burnup, fast fluence, temperature). These values are, however, indicated in each case. Fuel derived from uranium, thorium and a wide variety of plutonium grades has been considered. Long-lived actinide production and total residual decay heat were evaluated for the various types of fuel. The results presented in this papers provide a comparison of the potential and limits of each fuel cycle and allow to define specific cycles offering lowest actinide production and residual heat associated with a long life cycle. (author)

  5. Improvement of life insurance-related accounting opera-tions within the New Economy

    Directory of Open Access Journals (Sweden)

    Marinică DOBRIN

    2010-06-01

    Full Text Available This paper outlines the life insurance-related accounting operations, in consideration to the harmonization of the Romanian legislation with the International Financial Reporting Standards. The main accounting operations specific to the life insurance sector include: accounting of revenues and expenses derived from life insurance operations (recording the premiums written, recording the payment of insurance premiums, termination of insurance policy, recording the compensation expenses, accounting of operations related to the setting up and using the technical reserves for life insurance (general principles, accounting of premium reserves, accounting of loss reserve, accounting of the reserve for benefits and discounts, accounting of mathematical reserve, accounting of other life insurance-related technical reserves.

  6. Opening Session [International Conference on Fast Reactors and Related Fuel Cycles: Safe Technologies and Sustainable Scenarios (FR13), Paris, France, March 4-7, 2013

    International Nuclear Information System (INIS)

    Bigot, Bernard

    2013-01-01

    In Europe today, the energy supply relies on fossil fuels at over 75% of its primary energy consumption. Worldwide, it is over 82%. Such a massive use of fossil fuels is thus both a threat for the environment, climate and health, and also for our economies. In 2012, for France, fossil fuel imports represent an expense 3 times larger than in 2005, and over 90% of France’s trade deficit. If keeping this current energy mix, we will strongly contribute to a large increase of the risk of climate change, environmental and human health impacts, and their damaging effects. Tackling climate change, environmental and health issues will require the priority use of CO 2 emission free energy sources. Despite Kyoto protocol and many political international statements, the amount of CO 2 emission per year has known a +40% growth from 1990 to 2009, with the correlated increase of temperatures. To ensure a sustainable development, the world needs a sustainable energy supply, which makes a sufficient amount available for everybody at an acceptable price. For all these reasons, the substitution of fossil fuel consumption as soon as possible and as large as possible with CO 2 free energy sources must be our top priority. The corner stone of any sustainable European energy is the reduction of our consumption of fossil fuels with three axes of action relative to the technologies using these fuels: energy savings, improved efficiency, substitution by other technologies which do not use such fuels, as renewable and nuclear energies

  7. JPRS Report, Soviet Union, World Economy & International Relations, No. 1, January 1989.

    Science.gov (United States)

    1989-05-12

    Council ( ASTEC ). In his opinion, it is necessary before approaching a solution of problems of bilateral relations to get a clear idea of one’s partners...engineering products constitute a very negligible proportion. The task of the ASTEC is to expand bilateral trade and promote its development. But...that its further elaboration will not be long in coming. It was decided, given the direct assistance of the ASTEC , to create a "strike" group of

  8. Malaysia's Human Resource Strategies for a Knowledge-Based Economy - Comparing the Influence of Different Labur Market Relations

    DEFF Research Database (Denmark)

    Fleming, Daniel; Søborg, Henrik

    2010-01-01

    In the last 15-20 years the Malaysian government has sought to meet the increasing international competition in the labour intensive manufacturing industry by transforming the economy to a more knowledge-based economy. Impotant levers are industrial upgrading policies and partnerships with leadin...

  9. Impact of the energy-related inventions program on the national economy

    Energy Technology Data Exchange (ETDEWEB)

    Brown, M.A.; Morell, J.A.; Snell, S.A.; Kerley, C.R.

    1987-01-01

    The market entry, sales, and employment data presented in this paper suggest that ERIP has been able to efficiently produce positive economic impacts. It is likely that the documented successes of ERIP's inventors will be even greater as their projects mature and more current commercialization information is collected. Survey data presented elsewhere indicate that the ERIP financial support, endorsement, encouragement, and commercialization education are viewed by participants as the most important benefits of the program (Brown, Morell, Snell, Soderstrom, and Friggle, 1987). Other federal, state, and local programs might profit substantially from modelling the composition and delivery of their assistance after the Energy-Related Inventions Program.

  10. Relation of fuel rod service parameters and design requirements to produced fuel rod and their components

    International Nuclear Information System (INIS)

    Bibilashvili, Yu.K.

    1999-01-01

    Based on the presented material it is possible to state that there is a very close link between the fuel operational parameters and the requirements for its design and production process. The required performance and life-time of a fuel rod can be only assured by the correctly selected design and process solutions. The economical aspect of this problem is significantly depend on the commercial feasibility of a particular selected solution with the provision of an automated and comparative by inexpensive production of a fuel rod and its components. The operational conditions are also important for the life time of the fuel rods. If there are no special measures for the mitigation of the certain operation conditions the leakage of fuel elements can take place before the planned time. (authors)

  11. A Comparative Study of Trade Relations and the Spatial-Temporal Evolution of Geo-Economy between China and Vietnam

    Directory of Open Access Journals (Sweden)

    Teng Ma

    2017-06-01

    Full Text Available With the increasing economic importance of the Asia-Pacific Region, the economic interdependence among countries in the region has gradually enhanced. With the continuous opening up of the two countries, Sino-Vietnamese economic relations have also been deepened. However, the export trade between Vietnam and China has been competitive. China and Vietnam seek to dominate or join an agreement that is conducive to their own trade, which also exacerbates the trade competition between the two countries. This paper compares China and Vietnam and analyzes their foreign trade data from 2005 to 2014. By analyzing the competitiveness of export commodities, the trade division effect and spatio-temporal changes of the geo-economic relationship in the Asia-Pacific Region, this study explores Sino-Vietnamese trade relations and compares the pattern of geo-economic evolution between the two countries. The findings show that China and Vietnam have similarities and substitutability in textiles, apparel and footwear in terms of commodity structure. There is already a trade diversion effect between Vietnam and China on these commodities, but it is not substantial. From a geographic perspective, China’s geo-economic relations in the Pacific Rim present an increasingly dispersed trend. However, the spatial pattern of Vietnam’s geo-economy has maintained a low-level and stable spatial agglomeration over the last decade.

  12. Economy, Geopolitics, environment: the triple gas issue in the relations between the Eu and Russia

    International Nuclear Information System (INIS)

    Bourguignon, D.

    2008-01-01

    With the political tinge it has recently acquired, natural gas has taken a central position in the relations between the EU and Russia Besides energy security, the issue has three levels: the first is the opening of markets or the maintaining of monopolies, as much in Russia as in the European Union. The line of fracture is complex, and at present, in spite of rhetoric support on the opening of markets, it is rather their protection which is on the agenda. The second level is that of energy diplomacy Brussels and Moscow come face to face primarily in Central Asia, on the basis of interests and using diametrically opposite instrument. However, their policies are characterised by weighty constraints. The third level is that of the fight against climatic change. Soaring in this field, there are several convergencies between the policies of Brussels and Moscow, particularly in terms of energy efficiency. With this new order, gas could watch itself grow in significance, or otherwise drop, in which case the relation between the EU and Russian would not go uninfluenced. (author)

  13. Fuel pin bowing and related investigation of WWER-440 control rod influence on power release inside of neighbouring fuel pins

    International Nuclear Information System (INIS)

    Mikus, J.

    2005-01-01

    The purpose of this work consists in investigation of the WWER-440 control rod (CR) influence on space power distribution, especially from viewpoint of the values and gradient occurrence that could result in static and cyclic loads with some consequences, e.g. fuel pin bowing. As known, CR can cause power peaks in periphery fuel pins of adjacent operating assemblies because of the butt joint design of the absorbing adapter to the CR fuel part, that is, presence of the water cavity resulting in a flash up of thermal neutrons. As a consequence, beside well-known peaks in axial power distribution, above power gradients can occur inside of mentioned fuel pins. Because of complicated geometry and material composition of the CR, the detailed calculations concerning both above phenomena are complicated, too. Therefore it is useful to acquire appropriate experimental data to investigate mentioned influence and compare them with calculations. Since detailed power distributions cannot be obtained in the NPP, needed information is provided by means of experiments on research reactors. In case of measurements inside of fuel pins, special (e.g. track) detectors placed between fuel pellets are used. Such works are relatively complicated and time consuming, therefore an evaluation based on mathematical modelling and numerical approximation was proposed by means of that, and using measured power release in some selected fuel pins, information about power release inside of one of these fuel pins, can be obtained. For this purpose, an experiment on light water, zero-power research reactor LR-0 was realized and axial power distribution measurements were performed in a WWER-440 type core near to an authentic CR model. Application of the above evaluation method is demonstrated on one ''investigated'' fuel pin neighbouring CR by means of following results: 1. Axial power distribution inside of investigated fuel pin in two opposite positions on its pellets surface that are situated to

  14. Popular Education in Solidarity Economy

    Science.gov (United States)

    de Melo Neto, José Francisco; da Costa, Francisco Xavier Pereira

    2015-01-01

    This article seeks to show the relation between popular education and solidarity economy in experiences of solidarity economy enterprises in Brazil. It is based on diverse experiences which have occurred in various sectors of this economy, highlighting those experiences which took place in João Pessoa with the creation of a Cooperative of Workers…

  15. Sexual dimorphism in relation to big-game hunting and economy in modern human populations.

    Science.gov (United States)

    Collier, S

    1993-08-01

    Postcranial skeletal data from two recent Eskimo populations are used to test David Frayer's model of sexual dimorphism reduction in Europe between the Upper Paleolithic and Mesolithic. Frayer argued that a change from big-game hunting and adoption of new technology in the Mesolithic reduced selection for large body size in males and led to a reduction in skeletal sexual dimorphism. Though aspects of Frayer's work have been criticized in the literature, the association of big-game hunting and high sexual dimorphism is untested. This study employs univariate and multivariate analysis to test that association by examining sexual dimorphism of cranial and postcranial bones of two recent Alaskan Eskimo populations, one being big-game (whale and other large marine mammal) hunting people, and the second being salmon fishing, riverine people. While big-game hunting influences skeletal robusticity, it cannot be said to lead to greater sexual dimorphism generally. The two populations had different relative sexual dimorphism levels for different parts of the body. Notably, the big-game hunting (whaling) Eskimos had the lower multivariate dimorphism in the humerus, which could be expected to be the structure under greatest exertion by such hunting in males. While the exertions of the whale hunting economic activities led to high skeletal robusticity, as predicted by Frayer's model, this was true of the females as well as the males, resulting in low sexual dimorphism in some features. Females are half the sexual dimorphism equation, and they cannot be seen as constants in any model of economic behavior.

  16. Safety-related investigations on power distribution in MOX fuel elements in LWR cores

    International Nuclear Information System (INIS)

    Kramer, E.; Langenbuch, S.

    1991-01-01

    For the concept of thermal recycling various fuel assembly designs have been developped during the last years. An overview is given describing the present status of MOX-fuel assembly design for PWR and BWR. The local power distribution within the MOX-fuel assembly and influences between neighbouring MOX- and Uranium fuel assemblies have been analyzed by own calculations. These investigations are limited to specific aspects of the spatial power distribution, which are related to the use of MOX-fuel assemblies within the reactor core of LWR. (orig.) [de

  17. Moneyless Economy

    OpenAIRE

    Das, Subhendu

    2012-01-01

    Moneyless economy (MLE) does not have any money in the economy. All products and services are free for all people. This means everybody must work, work for free, and get everything they want for free also. Any work that a society needs is considered legitimate. MLE is not socialism. MLE has the ability to provide a lifestyle that anyone wants. We show that it is possible to run the exact same economy that we have now, in the exact same way, and without money. Any government of any country can...

  18. An overview of economic and technical issues related to LWR MOX fuel usage

    International Nuclear Information System (INIS)

    Malone, J.P.; Varley, G.; Goldstein, L.

    1999-01-01

    This paper will present comparisons of the economics of MOX versus UO 2 fuels. In addition to the economics of the front end, the scope of the comparison will include the back end of the fuel cycle. Management of spent MOX fuel assemblies presents utilities with some technical issues that can complicate spent fuel pool operation. Alternative spent fuel management methods, such as dry storage of spent MOX fuel assemblies, will also be discussed. Differences in decay heat loads versus time for spent MOX and UO 2 fuel assemblies will be presented. This difference is one of the main problems confronting spent fuel managers relative to MOX. The difference in decay heat loads will serve as the basis for a performance overview of the various spent fuel technologies available today. The economics of the front end of MOX will be presented relative to UO 2 fuel. Availability of MOX manufacturing capability will also be discussed, along with a discussion of its impact on future MOX fabrication prices. The in-core performance of MOX will be compared to that of UO 2 fuel with similar performance characteristics. The information will include highlights of nuclear design and related operational considerations such as: Reactivity reduction with burnup is slower for MOX fuel than for UO 2 fuel; Spectral hardening resulting in lower control rod worths and a lower soluble boron worth; and more negative moderator, void and fuel temperature coefficients. A comparison of Westinghouse and ABB-CE core designs for use on disposition of weapons MOX in 12- and 18-month cycles will be presented. (author)

  19. The Methanol Economy Project

    Energy Technology Data Exchange (ETDEWEB)

    Olah, George [Univ. of Southern California, Los Angeles, CA (United States); Prakash, G. K. [Univ. of Southern California, Los Angeles, CA (United States)

    2014-02-01

    The Methanol Economy Project is based on the concept of replacing fossil fuels with methanol generated either from renewable resources or abundant natural (shale) gas. The full methanol cycle was investigated in this project, from production of methanol through bromination of methane, bireforming of methane to syngas, CO2 capture using supported amines, co-electrolysis of CO2 and water to formate and syngas, decomposition of formate to CO2 and H2, and use of formic acid in a direct formic acid fuel cell. Each of these projects achieved milestones and provided new insights into their respective fields.

  20. Iran's Economy

    National Research Council Canada - National Science Library

    Ilias, Shayerah

    2008-01-01

    .... To the extent that U.S. sanctions and other efforts to change Iranian state policy target aspects of Iran ssssssss economy as a means of influence, it is important to evaluate Iran's economic structure, strengths, and vulnerabilities...

  1. Iran's Economy

    National Research Council Canada - National Science Library

    Ilias, Shayerah

    2008-01-01

    .... To the extent that U.S. sanctions and other efforts to change Iranian state policy target aspects of Iran's economy as a means of influence, it is important to evaluate Iran's economic structure, strengths, and vulnerabilities...

  2. Cambodia's economy

    OpenAIRE

    Ear, Sophal

    2008-01-01

    "This presentation is adapted from a Harvard KSG workshop held earlier this year on the Political Economy of "Binding Constraints to Growth" Cambodia Pilot for which I served as an External Panelist/Resource Person."

  3. Mobile economy

    OpenAIRE

    Turowski, Klaus

    2004-01-01

    Mobile economy : Transaktionen, Prozesse, Anwendungen und Dienste ; 4. Workshop Mobile Commerce, 02.-03. Februar 2004, Univ. Augsburg / K. Turowski ... (Hrsg.). - Bonn : Ges. für Informatik, 2004. - 189 S. : Ill., graph. Darst. - (GI-Edition : Proceedings ; 42)

  4. CURRENT TRENDS IN THE KNOWLEDGE ECONOMY

    Directory of Open Access Journals (Sweden)

    Ciprian Ionel HRETCANU

    2015-07-01

    Full Text Available In this paper we discuss various aspects of the current economy known as the knowledge economy. Also we will review two indicators of this new economy, because these indicators presents a general plan on access, use and degree of diffusion of knowledge. Then, based on these indicators and taking into account other aspects, we outline the structure relations between "new economy" and "digital economy". Finally we present the main types of business existing in the digital economy.

  5. ECONOMY AND SOCIAL ENVIRONMENT

    Directory of Open Access Journals (Sweden)

    Oleg BOGOMOLOV

    2008-12-01

    Full Text Available Market reforms in the post-socialist countries have brought into sharp focus the problem of interconnection and interaction between the economy and the social environment. The economy is inseparable from politics and the operation of the political system, from the state of the social consciousness, the moral and cultural level of the population and from many other aspects of human life and behavior, in short, from everything that can be described by the concept of social environment. Society in every country is a single organism with closely interconnected and interacting parts and systems. Their conjugation and mutual influence are not always apparent and are often overlooked. It is quite easy to see how changes in policy affect the economy and then trace the feedback effect of the economy on policy. It is more difficult to discern the direct and feedback relationship of the economy with administrative relations, with the state of culture, science, morals and public opinion. Meanwhile, an underestimation of these mutual influences is a frequent cause of failures in socio-economic transformation. It is to be regretted that the reforms in Russia were accompanied by a dangerous disruption not only of the economy, but also of the entire system of social relations. What was primary here and what was secondary? In order to answer this question the paper takes a theoretical look at the problem of interaction between the economy and the social environment.

  6. Neutron imaging methods for the investigation of energy related materials. Fuel cells, battery, hydrogen storage and nuclear fuel

    Science.gov (United States)

    Lehmann, Eberhard H.; Boillat, Pierre; Kaestner, Anders; Vontobel, Peter; Mannes, David

    2015-10-01

    After a short explanation of the state-of-the-art in the field of neutron imaging we give some examples how energy related materials can be studied successfully. These are in particular fuel cell studies, battery research approaches, the storage of hydrogen, but also some investigations with nuclear fuel components. The high contrast for light isotopes like H-1, Li-6 or B-10 are used to trace low amounts of material even within compact sealing of metals which are relatively transparent for neutrons at the same time.

  7. Analysis of the Relationship Between Vehicle Weight/Size and Safety, and Implications for Federal Fuel Economy Regulation

    Energy Technology Data Exchange (ETDEWEB)

    Wenzel, Thomas P.

    2010-03-02

    preferable unit of exposure to a serious crash than the number of registered vehicles. However, because there are relatively few fatalities in the states providing crash data, we calculate casualty risks, which are the sum of fatalities and serious or incapacitating injuries, per vehicle involved in a crash reported to the police. We can account for driver age/gender and driving location effects by excluding from analysis crashes (and casualties) involving young males and the elderly, and occurring in very rural or very urban counties. Using state data on all police-reported crashes in five states, we find that excluding crashes involving young male and elderly drivers has little effect on casualty risk; however, excluding crashes that occurred in the most rural and most urban counties (based on population density) increases casualty risk for all vehicle types except pickups. This suggests that risks for pickups are overstated unless they account for the population density of the county in which the crashes occur. After removing crashes involving young males and elderly drivers, and those occurring in the most rural and most urban counties, we find that casualty risk in all light-duty vehicles tends to increase with increasing weight or footprint; however, the correlation (R{sup 2}) between casualty risk and vehicle weight is 0.31, while the correlation with footprint is 0.23. These relationships are stronger for cars than for light trucks. The correlation between casualty risk in frontal crashes and light-duty vehicle wheelbase is 0.12, while the correlation between casualty risk in left side crashes and track width is 0.36. We calculated separately the casualty risks vehicles impose on drivers of the other vehicles with which they crash. The correlation between casualty risk imposed by light trucks on drivers of other vehicles and light truck footprint is 0.15, while the correlation with light truck footprint is 0.33; risk imposed on others increases as light truck weight

  8. Public relations campaign for shipping spent nuclear fuel

    Energy Technology Data Exchange (ETDEWEB)

    Bushee, Tom [Northern States Power Company, Minneapolis, MN (United States)

    1989-07-01

    An example of positive outcome of proper attitude of the media and public on the occasion of shipping of nuclear fuel is described. Nothing new was invented in the way of public relations issue management. But a combination of a number of proven techniques were put together and the public relations plan that was highly successful. early planning was of great help. Public officials were well informd by means of ANS organized seminars. ANS had experts from Sandia Labs (a major government research facility), General Electric (the cask supplier), the railroad we planned to use and Northern States Power Company on the program to describe what was going to happen and why it was safe. These sessions are believed to head off a major portion of the local opposition. A cooperation was established with the states of Wisconsin and Minnesota in providing shipment-specific training for emergency response personnel along the route. Safety, obviously, was the number one concern expressed by public officials. Knowing that would be the case, it was decided to provide some optional extras to go with the shipments. There was a consultant yo do a safety analysis of all the possible rail routes between the plant and storage facility. Though none was required by law, a shipment-specific emergency response plan which was prepared. Another important effort which was maintained from the beginning was sharing information among the participants. In dealing with the news media, an attemp was made to stick to a single source of information as much as possible. When dealing with the news media, one should refuse to apologize for modern technology. One should attack, at every opportunity, the idea that a ''risk-free'' society is worth the price of returning to the Dark Ages. The contributions of nuclear technology are numerous and far-reaching. Its negative impacts on health and safety have been minor compared with most other major industrial technologies. Certainly there is risk in stepping out

  9. Public relations campaign for shipping spent nuclear fuel

    International Nuclear Information System (INIS)

    Bushee, Tom

    1989-01-01

    An example of positive outcome of proper attitude of the media and public on the occasion of shipping of nuclear fuel is described. Nothing new was invented in the way of public relations issue management. But a combination of a number of proven techniques were put together and the public relations plan that was highly successful. early planning was of great help. Public officials were well informd by means of ANS organized seminars. ANS had experts from Sandia Labs (a major government research facility), General Electric (the cask supplier), the railroad we planned to use and Northern States Power Company on the program to describe what was going to happen and why it was safe. These sessions are believed to head off a major portion of the local opposition. A cooperation was established with the states of Wisconsin and Minnesota in providing shipment-specific training for emergency response personnel along the route. Safety, obviously, was the number one concern expressed by public officials. Knowing that would be the case, it was decided to provide some optional extras to go with the shipments. There was a consultant yo do a safety analysis of all the possible rail routes between the plant and storage facility. Though none was required by law, a shipment-specific emergency response plan which was prepared. Another important effort which was maintained from the beginning was sharing information among the participants. In dealing with the news media, an attemp was made to stick to a single source of information as much as possible. When dealing with the news media, one should refuse to apologize for modern technology. One should attack, at every opportunity, the idea that a r isk-freesociety is worth the price of returning to the Dark Ages. The contributions of nuclear technology are numerous and far-reaching. Its negative impacts on health and safety have been minor compared with most other major industrial technologies. Certainly there is risk in stepping out of

  10. Improvements in or relating to nuclear reactor fuel element assemblies

    International Nuclear Information System (INIS)

    Chetter, J.

    1975-01-01

    A description is given of a spacer grid comprising a substantially rigid grid structure formed from intersecting strip members defining cells which are penetrated by fuel pins bearing against rigid stops projecting inside the cells and spring locating members in the form of bow springs which extend longitudinally in the cells of the grid structure to hold the fuel pins against the rigid stops in the cells. The bow spring members of each line of cells extending in one direction across the grid structure have their corresponding ends interconnected by common longitudinal bridging strips to form a ladder spring assembly. (author)

  11. Signs of political economy

    Directory of Open Access Journals (Sweden)

    Bernard Lamizet

    2015-12-01

    Full Text Available Like any political system, economy is a system of signs and representations. The Semiotics of economy elaborates its analytical methods to interpret such signs, which give meaning to the economy by representing its performances in public debate and in the media. Four major features distinguish the Semiotics of political economy from other semiotic forms or other systems of information and political representation. First of all, the relationship between the signification of the economy and the real or the imaginary phenomena to which they refer always pertains to the order of values. The second characteristic of economic signs is the significance of the state of lack they express. The third characteristic of signs of the economy is the form of sign production, which can be designated by the concept of emission of signs and their diffusion. Finally, as all signs, the economic sign is arbitrary. In the field of Economics, such arbitrariness does not imply that the Subject is free to superimpose whatever value to the signs themselves, but refers to the rupture between the world and its possible transformation. The very meaning of the word economy is here at stake. Oikos, in Greek (the term from which the word economy is derived refers to a known, familiar space. Economy transforms the real, natural world into a symbolic social world, into a world of relations with others whom we recognise and whose actions are relatively predictable. It might be useful to consider the contemporary issue of debt, its implications and its multiple meanings, which includes both the ethical and moral dimension of the condemnation of debt as well as the imaginary political dimension based on the expression of an idea of independence.

  12. OECD/NEA Ongoing activities related to the nuclear fuel cycle

    International Nuclear Information System (INIS)

    Cornet, S.M.; McCarthy, K.; Chauvin, N.

    2013-01-01

    As part of its role in encouraging international collaboration, the OECD Nuclear Energy Agency is coordinating a series of projects related to the Nuclear Fuel Cycle. The Nuclear Science Committee (NSC) Working Party on Scientific Issues of the Nuclear Fuel Cycle (WPFC) comprises five different expert groups covering all aspects of the fuel cycle from front to back-end. Activities related to fuels, materials, physics, separation chemistry, and fuel cycles scenarios are being undertaken. By publishing state-of-the-art reports and organizing workshops, the groups are able to disseminate recent research advancements to the international community. Current activities mainly focus on advanced nuclear systems, and experts are working on analyzing results and establishing challenges associated to the adoption of new materials and fuels. By comparing different codes, the Expert Group on Advanced Fuel Cycle Scenarios is aiming at gaining further understanding of the scientific issues and specific national needs associated with the implementation of advanced fuel cycles. At the back end of the fuel cycle, separation technologies (aqueous and pyrochemical processing) are being assessed. Current and future activities comprise studies on minor actinides separation and post Fukushima studies. Regular workshops are also organized to discuss recent developments on Partitioning and Transmutation. In addition, the Nuclear Development Committee (NDC) focuses on the analysis of the economics of nuclear power across the fuel cycle in the context of changes of electricity markets, social acceptance and technological advances and assesses the availability of the nuclear fuel and infrastructure required for the deployment of existing and future nuclear power. The Expert Group on the Economics of the Back End of the Nuclear Fuel Cycle (EBENFC), in particular, is looking at assessing economic and financial issues related to the long term management of spent nuclear fuel. (authors)

  13. Summary of fuel economy performance

    Science.gov (United States)

    2009-12-09

    This report contains estimated fleet production numbers and CAFE figures obtained from pre-model year (source I) and mid-model year (source 2) documents assembled prior to or during the model year. The actual mpg values reported to EPA at the end of ...

  14. Safety criteria related to microheterogeneities in LWR mixed oxide fuels

    International Nuclear Information System (INIS)

    Renard, A.; Mostin, N.

    1978-01-01

    The main safety aspets of PuO 2 microheterogeneities in the pellets of LWR mixed oxide fuels are reviewed. Points of interest are studied, especially the transient behaviour in accidental conditions and criteria are deduced for use in the specification and quality control of the fabricated product. (author)

  15. Analytic tests and their relation to jet fuel thermal stability

    Energy Technology Data Exchange (ETDEWEB)

    Heneghan, S.P.; Kauffman, R.E. [Univ. of Dayton Research Institute, OH (United States)

    1995-05-01

    The evaluation of jet fuel thermal stability (TS) by simple analytic procedures has long been a goal of fuels chemists. The reason is obvious: if the analytic chemist can determine which types of material cause his test to respond, the refiners will know which materials to remove to improve stability. Complicating this quest is the lack of an acceptable quantitative TS test with which to compare any analytic procedures. To circumvent this problem, we recently compiled the results of TS tests for 12 fuels using six separate test procedures. The results covering a range of flow and temperature conditions show that TS is not as dependent on test conditions as previously thought. Also, comparing the results from these tests with several analytic procedures shows that either a measure of the number of phenols or the total sulfur present in jet fuels is strongly indicative of the TS. The phenols have been measured using a cyclic voltammetry technique and the polar material by gas chromatography (atomic emission detection) following a solid phase extraction on silica gel. The polar material has been identified as mainly phenols (by mass spectrometry identification). Measures of the total acid number or peroxide concentration have little correlation with TS.

  16. Overview of safeguards aspects related to MOX fuel

    International Nuclear Information System (INIS)

    Heinonen, O.J.; Murakami, K.; Shea, T.

    2000-01-01

    Recent developments in the light of the IAEA verification requirements for MOX fuel at reactors and bulk handling facilities are discussed. Impact of the Additional Protocol and Integrated Safeguards System is briefly addressed. Agency's work undertaken with regard to the nuclear arms control and reduction is presented. (author)

  17. Safety problems related to microheterogeneities in physically mixed oxide fuels

    International Nuclear Information System (INIS)

    Renard, A.; Evrard, G.; Vanhellemont, G.

    1976-01-01

    The safety aspects of microheterogeneities in LMFBR mixed oxide fuel are reviewed from the point of view of the pin behaviour dynamic study, the fabrication and the quality control. The paper emphasizes some significant parameters in transient conditions, the prevention means in the fabrication process and the analysis methods for the control

  18. RELATIVE PROLIFERATION RISKS FOR NUCLEAR FUEL LEASING ARRANGEMENT

    International Nuclear Information System (INIS)

    CHENG, L.Y.; YUE, M.; BARI, R.A.

    2007-01-01

    The present study demonstrates a probabilistic approach to quantify the proliferation risks of fuel leasing and recycling. A Markov model approach is applied to evaluate the probability of proliferation success by diversion or theft. Proliferation risk is calculated as a product of the probability of success and the corresponding consequences

  19. Regulating the sharing economy

    OpenAIRE

    Erickson, Kristofer; Sorensen, Inge

    2016-01-01

    In this introductory essay, we explore definitions of the ‘sharing economy’, a concept indicating both social (relational, communitarian) and economic (allocative, profit-seeking) aspects which appear to be in tension. We suggest combining the social and economic logics of the sharing economy to focus on the central features of network enabled, aggregated membership in a pool of offers and demands (for goods, services, creative expressions). This definition of the sharing economy distinguishe...

  20. Ash related behaviour in staged and non-staged combustion of biomass fuels and fuel mixtures

    International Nuclear Information System (INIS)

    Becidan, Michaël; Todorovic, Dusan; Skreiberg, Øyvind; Khalil, Roger A.; Backman, Rainer; Goile, Franziska; Skreiberg, Alexandra; Jovovic, Aleksandar; Sørum, Lars

    2012-01-01

    The fate of selected elements (with focus on the important players in corrosion i.e. Na, K, Pb, Zn, Cl and S) are investigated for three biomasses (wood, demolition wood and coffee waste) and six mixtures of these as pellets both with and without air staging in a laboratory reactor. In order to get a complete overview of the combustion products, both online and offline analytical methods are used. Information is collected about: flue gas composition, particle (fly ash) size distribution and composition, bottom ash composition and melting properties. The main findings are: (1) complex interactions are taking place between the mixed fuels during combustion; (2) the mode of occurrence of an element as well as the overall structure of the fuel are important for speciation; (3) the pelletisation process, by bringing chemical elements into intimate contact, may affect partitioning and speciation; (4) staging and mixing might simultaneously have positive and negative effects on operation; (5) staging affects the governing mechanisms of fly ash (aerosols) formation. -- Highlights: ► Complex interactions are taking place between the mixed fuels during combustion. ► The mode of occurrence of an element as well as the overall structure of the fuel are important for speciation. ► The pelletisation process, by bringing chemical elements into intimate contact, may affect partitioning and speciation. ► Staging and mixing might simultaneously have positive and negative effects on operation. ► Staging affects the governing mechanisms of fly ash (aerosols) formation.

  1. The effects of the final disposal facility for spent nuclear fuel on regional and municipal economy assessment of socio economical impacts

    International Nuclear Information System (INIS)

    Laakso, S.; Kuisma, H.; Kilpelaeinen, P.; Kostiainen, E.

    2007-12-01

    The aim of this study is to give an up-to-date assessment of the effects the construction of the final disposal facility for spent nuclear fuel in Eurajoki, based on latest knowledge. The disposal facility's effects on employment, population, housing construction, community structure and economy are estimated in the municipality of Eurajoki and in the wider region under the influence of the facility. The time-span of the report reaches from 2001 to the early 2020's when the facility will be in operation. The investment in research and construction of the disposal facility during the years 2004-2020 will be all together approximately 290 million euros. The estimation for the overall effect on national employment during the years 2001-2020 is circa 6 800 manyears, of which 4 200 man-years are from direct effects and 2 600 from indirect effects. The direct employment effects of the project will be at its highest approximately 325 man-year per year in 2020. The direct effect on employment during the operational period is estimated to be circa 130 man-years per year, of which the share of regular employees of Posiva is slightly over 100 man-years. At its highest, about 45 man-years per year of the total effect on employment (direct + indirect effects) will be directed to Eurajoki municipality. During the operational phase the share of Eurajoki is estimated to be circa 30 man-years per year. For the whole region, the effect of the disposal facility on employment will be significant, at its height in 2020, approximately 220 man-years per year. The disposal facility will also have an effect on the size and the structure of the population due to changes in employment and jobs. The estimation for the cumulative effect on the growth of the population caused by the facility is 80 more inhabitants in Eurajoki by 2020, which corresponds to 1,4 % of the municipality's current population. The growth of the population brought about by the facility in the whole region is estimated

  2. Dynamic Economy: the case for a new economic order based on dynamics and related to the value of energy

    Energy Technology Data Exchange (ETDEWEB)

    Bradbury, F

    1980-09-01

    Traditional economic tools are unable to deal with the scale and rapid interactions of today's world economies. The outstripping of these regulators by events finds them with neither the gain nor the response rate even to deal with classic problems like involuntary monetary inflation, enforced unemployment, political insecurity, and human drudgery. The Dynamic Economy may be achieved, uses control techniques, and builds upon the known elements of wealth, effort, and energy, to provide a fast, accurate feedback of the unit of added value. 4 references.

  3. Problems relating to international transport of nuclear fuels

    International Nuclear Information System (INIS)

    Timm, U.E.

    1985-01-01

    Owing to the tremendous geographic distances between uranium deposits of interest, to the various degrees of sophistication of nuclear industry in industrialized countries and to the close international cooperation in the field of nuclear energy, safe international transports, physical protection and transport handling play an important role. It is suggested to better coordinate the activities of nuclear power plant operators, the nuclear industry and specialized transport companies with respect to all national and international issues of nuclear fuel transports. (DG) [de

  4. Measurements relating fire radiative energy density and surface fuel consumption - RxCADRE 2011 and 2012

    Science.gov (United States)

    Andrew T. Hudak; Matthew B. Dickinson; Benjamin C. Bright; Robert L. Kremens; E. Louise Loudermilk; Joseph J. O' Brien; Benjamin S. Hornsby; Roger D. Ottmar

    2016-01-01

    Small-scale experiments have demonstrated that fire radiative energy is linearly related to fuel combusted but such a relationship has not been shown at the landscape level of prescribed fires. This paper presents field and remotely sensed measures of pre-fire fuel loads, consumption, fire radiative energy density (FRED) and fire radiative power flux density (FRFD),...

  5. Study on new-type fuel-related assembly handling tools for PWR NPP

    International Nuclear Information System (INIS)

    Fan Xiumei

    2013-01-01

    This article describes the design and study on a set of new-type fuel-related assembly snatching tools used for PWR NPP. The purpose is mainly to enhance the tool safety, reliability and convenientness by improvement of the mechanism and structure of the tool for snatching preciseness and avoiding from falling and abrasion of fuel-related assemblies for any condition. The new-type fuel-related assembly handling tools are compared with similar equipment in worldwide in terms of function, main technical characteristic, and safety and protection, some of them are better than the similar equipment in that they have reliable loading and unloading and conveying capabilities. (author)

  6. Software Solution of Web Questionnaires for the Analysis of the Economy in Relation to the Competence of Students

    Science.gov (United States)

    Simeunovic, Vlado; Milic, Sanja

    2018-01-01

    The basic idea of the research was to take advantage of IT and establish a direct contact between businesses (employers) and universities in order to exchange relevant data on the knowledge, skills and competencies of students who got their first job in the economy. We used the best practices from previous papers that dealt with designing web…

  7. Human economy and natural economy

    Directory of Open Access Journals (Sweden)

    Masullo Andrea

    2014-03-01

    Full Text Available The decline of economy is due to its dependency from a virtual value, the currency, the coin, that in the recent phase of consumerism is so far from real value: human capital and natural capital. If human economy wants to continue to produce wellbeing, it must accept to be a subset of natural economy, intercept flux of matter produced by its circular mechanisms, put constraints in it, i.e. machines and structures, to direct it temporarily for our advantage, and finally release it to the same original flux, in an still usable state. In this way it will assume a function no more parasitic but symbiotic. It will be connected to natural cycles without destroying it, recovering the co-evolutionary link between nature and culture, building an economic web suited to the ecological web; thus we will have a mosaic characterised by biodiversity, technological diversity, and cultural diversity, able to produce a durable prosperity.

  8. 49 CFR 536.10 - Treatment of dual-fuel and alternative fuel vehicles-consistency with 49 CFR part 538.

    Science.gov (United States)

    2010-10-01

    ... vehicles-consistency with 49 CFR part 538. 536.10 Section 536.10 Transportation Other Regulations Relating... vehicles—consistency with 49 CFR part 538. (a) Statutory alternative fuel and dual-fuel vehicle fuel... economy in a particular compliance category by more than the limits set forth in 49 U.S.C. 32906(a), the...

  9. Review of spent fuel related issues in SKB's SR 97

    Energy Technology Data Exchange (ETDEWEB)

    Grambow, B. [Ecole des Mines de Nantes (France). SUBATECH-Laboratory

    2000-12-01

    The solid waste form 'spent fuel' constitutes both the dominant radionuclide source as well as a first radionuclide retention barrier of a planned future high level nuclear waste isolation systems in deep granite formations. In order to evaluate the performance of spent fuel as part of the multibarrier containment system in a deep repository, the radionuclide release properties in groundwater must be predicted over very long time periods. Radionuclide release is not an inherent materials property of the fuel but depends, besides fuel specific parameters, mainly on time but as well on the geochemical and hydraulic environment of the disposal location. The study SR 97 documents the large effort of SKB to assess the long-term performance of a repository containing spent nuclear fuel. Scenario and consequence analyses are clearly described, considering major physical and chemical interactions of the various components of the multi-barrier isolation system. The approach attempts to assess both a realistic and a pessimistic evolution scenario. The present report attempts to evaluate whether this approach is thoroughly carried through to assess the performance of spent nuclear fuel in a repository. Main issues are radionuclide inventories and inventory distribution between structural parts of the fuel assembly and the fuel matrix, potential fuel alteration prior to water access, as well as models for fuel matrix dissolution and instant release fractions. Uncertainties in radionuclide inventories are discussed and were found for many radionuclides to be higher than assumed in SR 97. This is particularly true for Cl-36. This nuclide is a potential key biosphere dose contributor in various international safety assessments. Of particular importance are uncertainties related to the partition of radionuclides between metallic parts of the fuel assembly and the fuel matrix, since inventories of metallic parts are considered to be released instantaneously. Using C-14 as

  10. Investigation of the Behavior of Fuel in the Intake Manifold and its Relation to S. I. Engines, 1980-1983

    Science.gov (United States)

    Servati, Hamid Beyragh

    A liquid fuel film formation on the walls of an intake manifold adversely affects the engine performance and alters the overall air/fuel ratio from that scheduled by a fuel injector or carburetor and leads to adverse effects in vehicle driveability, exhaust emissions, and fuel economy. In this dissertation, the intake manifold is simulated by a horizontal circular duct. A model is provided to predict the rate of deposition and evaporation of the droplets in the intake manifold. The liquid fuel flow rate into the cylinders, mean film velocity and film thickness are determined as functions of engine parameters for both steady and transient operating conditions of the engine. A mathematical engine model is presented to simulate the dynamic interactions of the various engine components such as the air/fuel inlet element, intake manifold, combustion, dynamics and exhaust emissions. Inputs of the engine model are the intake manifold pressure and temperature, throttle angle, and air/fuel ratio. The observed parameters are the histories of fuel film thickness and velocity, fuel consumption, engine speed, engine speed hesitation time, and histories of CO, CO(,2), NO(,x), CH(,n), and O(,2). The effects of different air/fuel ratio control strategies on engine performance and observed parameters are also shown.

  11. Europe - the first hydrogen economy?

    International Nuclear Information System (INIS)

    Hart, D.

    1999-01-01

    An examination of the state of research relating to hydrogen production and utilization indicates that interest in hydrogen from major companies in Europe has increased by several orders of magnitude in recent years. Of the three major areas where a hydrogen economy could be expected to start, namely, Japan, the United States and Europe, the latter may have advantages in diversity of resources, attitudes towards environmental issues and specific fiscal and regulatory structures. Examples of ongoing research and development projects in Europe include Norway's hydrogen combustion turbine to run on hydrogen from decarbonised natural gas, a project in the Netherlands involving mixing hydrogen and methane in the natural gas grid and a variety of projects involving liquid hydrogen refuelling, hydrogen aircraft, hydrogen fuelling stations and fuel cell vehicle development. There are also ongoing projects in carbon sequestration and hydrogen production for power generation and vehicle use. The author's main contention is that the combination of natural surroundings, environmental problems and attitudes, and business and government frameworks strongly suggest that Europe may be the first to have a hydrogen-based economy. 8 refs

  12. Fission gas release and fuel rod chemistry related to extended burnup

    International Nuclear Information System (INIS)

    1993-04-01

    The purpose of the meeting was to review the state of the art in fission gas release and fuel rod chemistry related to extended burnup. The meeting was held in a time when national and international programmes on water reactor fuel irradiated in experimental reactors were still ongoing or had reached their conclusion, and when lead test assemblies had reached high burnup in power reactors and been examined. At the same time, several out-of-pile experiments on high burnup fuel or with simulated fuel were being carried out. As a result, significant progress has been registered since the last meeting, particularly in the evaluation of fuel temperature, the degradation of the global thermal conductivity with burnup and in the understanding of the impact on fission gas release. Fifty five participants from 16 countries and one international organization attended the meeting. 28 papers were presented. A separate abstract was prepared for each of the papers. Refs, figs, tabs and photos

  13. Japanese perspectives and research on packaging, transport and storage of spent fuel

    International Nuclear Information System (INIS)

    Saegusa, T.; Ito, C.; Yamakawa, H.; Shirai, K.

    2004-01-01

    The Japanese policy on spent fuel is reprocessing. Until, reprocessed, spent fuel shall be stored properly. This paper overviews current status of transport and storage of spent fuel with related research in Japan. The research was partly carried out under a contract of Ministry of Economy, Trade and Industry of the Japanese government

  14. Regulating the sharing economy

    Directory of Open Access Journals (Sweden)

    Kristofer Erickson

    2016-06-01

    Full Text Available In this introductory essay, we explore definitions of the ‘sharing economy’, a concept indicating both social (relational, communitarian and economic (allocative, profit-seeking aspects which appear to be in tension. We suggest combining the social and economic logics of the sharing economy to focus on the central features of network enabled, aggregated membership in a pool of offers and demands (for goods, services, creative expressions. This definition of the sharing economy distinguishes it from other related peer-to-peer and collaborative forms of production. Understanding the social and economic motivations for and implications of participating in the sharing economy is important to its regulation. Each of the papers in this special issue contributes to knowledge by linking the social and economic aspects of sharing economy practices to regulatory norms and mechanisms. We conclude this essay by suggesting future research to further clarify and render intelligible the sharing economy, not as a contradiction in terms but as an empirically observable realm of socio-economic activity.

  15. Oil exploitation regulational framework and effects in the sector and its relation to the whole economy: the case of Brazil’s 1997 change

    Directory of Open Access Journals (Sweden)

    Rodrigo Emmanuel Santana Borges

    2012-01-01

    Full Text Available The world lives a context of energetic pre-crisis, and Brazil has discovered newbig reserves of the “black gold”, which led to changing the regulation framework of itsexploitation in the country. This paper focuses in analysis, from last years, thechanges in oil production and tries to evaluate its effects in growth of production andits links to the rest of Brazilian economy. Using data derived from the I-O matrix in thesupply side, and Balance of Payments data, we try to see if there were meaningfulchanges in the period 1998-2007 from the period 1990-1997 in terms of the oil sectorlinkage to the rest of the economy, technological modernization, its relation toemployment and average earnings, and its impacts in the external insertion of thecountry (exports and dividends balance.

  16. OIL EXPLOITATION REGULATIONAL FRAMEWORK AND EFFECTS IN THE SECTOR AND ITS RELATION TO THE WHOLE ECONOMY: THE CASE OF BRAZIL’S 1997 CHANGE

    Directory of Open Access Journals (Sweden)

    Rodrigo Emmanuel Santana Borges

    2012-09-01

    Full Text Available The world lives a context of energetic pre-crisis, and Brazil has discovered new big reserves of the “black gold”, which led to changing the regulation framework of its exploitation in the country. This paper focuses on the last change in that framework, in 1997, and tries to evaluate its effects in the production and its links to the rest of Brazilian economy. Using data derived from the I-O matrix in the supply side, and Balance of Payments data, we try to see if there were meaningful changes in the period 1998-2007 from the period 1990-1997 in terms of the oil sector linkage to the rest of the economy, technological modernization, its relation to employment and average earnings , and its impacts in the external insertion of the country (exports and dividends balance.

  17. Relative price level developments in the Baltic economies and lessons to learn from the crises. Suhteline hinnatase Balti riikide majandustes ja kriisikogemused

    Directory of Open Access Journals (Sweden)

    Meelis Angerma

    2012-01-01

    Full Text Available Estonia and other Baltic countries experienced speculative boom in years 2004-2008. The boom resulted in rapidly rising relative price level or real exchange rate. Euro wages are used as proxies for bilateral real exchange rates. Rapid reversal of capital inflow created instantly short-term real exchange rate overvaluation. The data shows that some other developing countries, like Poland and Russia let their price level to adjust through depreciation of nominal exchange rate. Estonia and other Baltic countries decided to go through adjustment with deflation of prices and wages. This contributed to higher unemployment rate and GDP loss. The most positive way out appears to be restoration of foreign investors interest in local economy and raising equilibrium real exchange rate reducing likely real exchange rate overvaluation. The other important implication was that local businessmen and other individuals were too much risk-takers for volatile emerging market economy.

  18. Gaining Control of Iraq's Shadow Economy

    National Research Council Canada - National Science Library

    Ramirez, David S

    2007-01-01

    .... These conditions fuel a sprawling, decades-old shadow economy manipulated by elements of organized crime, militias, and insurgents to fund attacks on Coalition forces, infrastructure and innocent Iraqi civilians...

  19. Hydrogen economy: a little bit more effort

    International Nuclear Information System (INIS)

    Pauron, M.

    2008-01-01

    In few years, the use of hydrogen in economy has become a credible possibility. Today, billions of euros are invested in the hydrogen industry which is strengthened by technological advances in fuel cells development and by an increasing optimism. However, additional research efforts and more financing will be necessary to make the dream of an hydrogen-based economy a reality

  20. Nuclear energy in the hydrogen economy

    International Nuclear Information System (INIS)

    Bertel, E.; Lee, K.S.; Nordborg, C.

    2004-01-01

    In the framework of a sustainable development, the hydrogen economy is envisaged as an alternative scenario in substitution to the fossil fuels. After a presentation of the hydrogen economy advantages, the author analyzes the nuclear energy a a possible energy source for hydrogen production since nuclear reactors can produce both the heat and electricity required for it. (A.L.B.)

  1. Technical Meeting on Fast Reactors and Related Fuel Cycle Facilities with Improved Economic Characteristics. Working Material

    International Nuclear Information System (INIS)

    2013-01-01

    The objectives of the meeting were: - To identify the main issues and technical features that affect capital and energy production costs of fast reactors and related fuel cycle facilities; - To present fast reactor concepts and designs with enhanced economic characteristics, as well as innovative technical solutions (components, subsystems, etc.) that have the potential to reduce the capital costs of fast reactors and related fuel cycle facilities; - To present energy models and advanced tools for the cost assessment of innovative fast reactors and associated nuclear fuel cycles; - To discuss the results of studies and on-going R&D activities that address cost reduction and the future economic competitiveness of fast reactors; and - To identify research and technology development needs in the field, also in view of new IAEA initiatives to help and support Member States in improving the economic competitiveness of fast reactors and associated nuclear fuel cycles

  2. Technical Meeting on Fast Reactors and Related Fuel Cycle Facilities with Improved Economic Characteristics. Presentations

    International Nuclear Information System (INIS)

    2013-01-01

    The objectives of the meeting were: • To identify the main issues and technical features that affect capital and energy production costs of fast reactors and related fuel cycle facilities; • To present fast reactor concepts and designs with enhanced economic characteristics, as well as innovative technical solutions (components, subsystems, etc.) that have the potential to reduce the capital costs of fast reactors and related fuel cycle facilities; • To present energy models and advanced tools for the cost assessment of innovative fast reactors and associated nuclear fuel cycles; • To discuss the results of studies and ongoing R&D activities that address cost reduction and the future economic competitiveness of fast reactors; • To identify research and technology development needs in the field, also in view of new IAEA initiatives to help and support Member States in improving the economic competitiveness of fast reactors and associated nuclear fuel cycles

  3. The Brazilian strategy for the hydrogen economy; A estrategia brasileira para economia do hidrogenio

    Energy Technology Data Exchange (ETDEWEB)

    Matos, Maiana Brito de [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Fac. de Engenharia Mecanica; Neves Junior, Newton Pimenta

    2008-07-01

    This paper examines the Brazilian strategy in the development of technology related to hydrogen and the fuel cell systems. The Brazilian program and road map in the area are analyzed: the Program on Science, Technology and Innovation for the Hydrogen Economy - Pro H2, former Brazilian Program of the Fuel Cell Systems-ProCaC which was created in 2002 by the Ministry of Science, Technology - MCT, and the Road map for Structuring of the Hydrogen Economy in Brazil, which was created in 2004 by the Ministry of Mines and Energy - MME. (author)

  4. SOCIAL ECONOMY EFFICIENCY

    Directory of Open Access Journals (Sweden)

    Florina Oana Virlanuta

    2015-05-01

    Full Text Available The social economy combines profitability with social inclusion. Social innovation is the first step in the creation of a social enterprise. Social economy development is a process underway, innovative in terms of relating the individual to the production processes, the concept of citizenship, production areas and modalities. The concern for sustainable development, analysis of economic and financial crisis, the issue of the relationship between the individual and the production process open up many opportunities for development that can influence public policies on employment and social cohesion.

  5. Multi-objective regulations on transportation fuels: Comparing renewable fuel mandates and emission standards

    International Nuclear Information System (INIS)

    Rajagopal, D.; Plevin, R.; Hochman, G.; Zilberman, D.

    2015-01-01

    We compare two types of fuel market regulations — a renewable fuel mandate and a fuel emission standard — that could be employed to simultaneously achieve multiple outcomes such as reduction in fuel prices, fuel imports and greenhouse gas (GHG) emissions. We compare these two types of regulations in a global context taking into account heterogeneity in carbon content of both fossil fuels and renewable fuels. We find that although neither the ethanol mandate nor the emission standard is certain to reduce emissions relative to a business-as-usual baseline, at any given level of biofuel consumption in the policy region, a mandate, relative to an emission standard, results in higher GHG emissions, smaller expenditure on fuel imports, lower price of ethanol-blended gasoline and higher domestic fuel market surplus. This result holds over a wide range of values of model parameters. We also discuss the implications of this result to a regulation such as the US Renewable Fuel Standard given recent developments within the US such as increase in shale and tight oil production and large increase in average vehicle fuel economy of the automotive fleet. - Highlights: • Biofuel mandates and fuel GHG emission standards are analyzed from a multiple criteria perspective • An emission-standard always results in lower global emissions while requiring less biofuel relative to a biofuel mandate • An emission-standard results in higher fuel price in the home region relative to a biofuel mandate • Emission standards lead to more shuffling of both fossil fuels and biofuels between home and abroad • The relative impact of the policies on fuel imports depends on the relative cost-effectiveness of domestic & imported biofuel • Recent developments oil production and fuel economy increase the net benefits of an LCFS approach relative to RFS

  6. Attitudes toward Sustainability and Green Economy Issues Related to Some Students Learning Their Characteristics: A Preliminary Study

    Directory of Open Access Journals (Sweden)

    Andrea Micangeli

    2014-05-01

    Full Text Available The present paper proposes and describes a new method, called L2A (listen-to-apprise, conceived of in order to improve the commitment of all the participants involved in an educational process specifically dedicated to sustainability and the green economy. The first stage consists in listening to the students and, when possible, in listening to the environment, the people, and the territory, while, in the second stage, the acquired information is used to exploit everyone’s talents and to achieve the maximum advantage and satisfaction for all. The first phase of L2A is mainly dedicated to listening to the students via the submission of an on-line questionnaire that measures their learning preferences, self-efficacy and sensitivity to the themes of sustainability and the green economy. The investigation has been extended from Italy to Honduras, where the authors are involved in the development of major projects concerning sustainability. The results of the survey have been analyzed by means of standard significance and correlation analysis, and therefore, significant differences among the groups and correlations within each group have been detected. The results have been discussed in order to explain how the L2A method works and how useful and powerful a tool it could be to improve teaching, learning and practical activities.

  7. Microstructural characteristics of PWR [pressurized water reactor] spent fuel relative to its leaching behavior

    International Nuclear Information System (INIS)

    Wilson, C.N.

    1986-01-01

    Microstructural, compositional and thermochemical properties of spent nuclear fuel are discussed relative to its potential performance as a high-level waste form under proposed Nevada Nuclear Waste Storage Investigations Project tuff repository conditions. Pressurized water reactor spent fuel specimens with various artificially induced cladding defects were leach tested in deionized water and in a reference tuff groundwater under ambient hot cell air and temperature conditions. Greater fractional actinide release was observed with bare fuel than with clad fuel leached through a cladding defect. Congruent actinide release and preferential release of cesium and technetium were observed in both water types. Selected summary radionuclide release data are presented and correlated to pre- and post-test microstructural characterization data

  8. Fuel pin bowing and related investigation of the gadolinium fuel pin influence on power release inside of neighbouring fuel pins in a WWER-440 type core

    International Nuclear Information System (INIS)

    Mikus, J.

    2006-01-01

    As known both the WWER-440 and WWER-1000 reactors are systematically modernized to enhance their safety and economical parameters of operation. For this purpose new fuel assemblies (FAs) were designed with improved technical parameters, e.g., containing fuel pins (FPs) in which Gd 2 O 3 burnable absorber is integrated into fuel. Presence of such FPs in reactor core results in a strong depression of thermal neutrons in their positions and corresponding high gradients in neighbouring FPs. Consequently, similar situation in neighbouring FPs can be expected as for both the power release and temperature gradients. The purpose of this work consists in investigation of the gadolinium FP influence on space power distribution, especially from viewpoint of the values and gradient occurrence inside of the neighbouring FPs that could result in static loads with some consequences, e.g., a contribution to FP/FA bowing. Since detailed power distributions cannot be obtained in the NPPs, needed information is provided by means of experiments on research reactors. As for the power release measurement inside of FPs, some special (e.g. track) detectors placed between fuel pellets are usually used. Since such works are relatively complicated and time consuming, an evaluation method based on mathematical modelling and numerical approximation was proposed by means of that, and using measured (integral) power release in selected FPs, needed power release values inside of investigated FPs, can be estimated. For this purpose, experimental results from light water, zero-power research reactor LR-0 obtained by measurements in a WWER-440 type core with 19 FAs at zero boron concentration and containing some FPs with gadolinium (Gd FPs) were utilized. Application of the proposed evaluation method is demonstrated on investigated FPs neighbouring a Gd FP by means of the: relative azimuthal power distribution estimation inside of investigated FPs on their fuel pellet surface in horizontal plane

  9. Improved correlations of hydrogen content versus combustion performance related properties of aviation turbine fuels

    Energy Technology Data Exchange (ETDEWEB)

    Nagpal, J.M.; Sharma, R.L.; Sagu, M.L.; Tiwari, G.B. (Indian Institute of Petroleum, Dehradun (India))

    1994-01-01

    In recent years the hydrogen content of Aviation Fuels has generated considerable interest. Various investigators have suggested correlation of hydrogen content with combustion related properties of aviation turbine fuel (ATF). A suitable threshold value of hydrogen content 13.8 wt% is being considered as a waiver of specifications such as specific energy, aniline gravity product, smoke point, aromatic content, naphthalenes and luminometer number. In the present paper relationship between the hydrogen content and combustion related properties has been examined and improved correlations of hydrogen content with several combustion related properties have been developed by incorporating a characterization factor in the equations. The supporting threshold value of a hydrogen content of 13.8wt% is verified with 25 data points for waiving of combustion properties such as specific energy, aniline gravity product, smoke point and aromatic content from aviation turbine fuel. 6 refs., 12 figs., 2 tabs.

  10. Fuel taxes, motor vehicle emission standards and patents related to the fuel-efficiency and emissions of motor vehicles. Joint Meetings of Tax and Environment Experts

    International Nuclear Information System (INIS)

    Vollebergh, H.

    2010-01-01

    Contribution to the project on Taxation, Innovation and the Environment of OECD's Joint Meetings of Tax and Environment Experts. It studies the impacts of motor vehicle fuel taxes and mandatory fuel efficiency standards on relevant car-related innovation activity in selected car-producing countries.

  11. Nuclear fuel cycle risk assessment: survey and computer compilation of risk-related literature

    International Nuclear Information System (INIS)

    Yates, K.R.; Schreiber, A.M.; Rudolph, A.W.

    1982-10-01

    The US Nuclear Regulatory Commission has initiated the Fuel Cycle Risk Assessment Program to provide risk assessment methods for assistance in the regulatory process for nuclear fuel cycle facilities other than reactors. Both the once-through cycle and plutonium recycle are being considered. A previous report generated by this program defines and describes fuel cycle facilities, or elements, considered in the program. This report, the second from the program, describes the survey and computer compilation of fuel cycle risk-related literature. Sources of available information on the design, safety, and risk associated with the defined set of fuel cycle elements were searched and documents obtained were catalogued and characterized with respect to fuel cycle elements and specific risk/safety information. Both US and foreign surveys were conducted. Battelle's computer-based BASIS information management system was used to facilitate the establishment of the literature compilation. A complete listing of the literature compilation and several useful indexes are included. Future updates of the literature compilation will be published periodically. 760 annotated citations are included

  12. Automotive Fuel Processor Development and Demonstration with Fuel Cell Systems

    Energy Technology Data Exchange (ETDEWEB)

    Nuvera Fuel Cells

    2005-04-15

    The potential for fuel cell systems to improve energy efficiency and reduce emissions over conventional power systems has generated significant interest in fuel cell technologies. While fuel cells are being investigated for use in many applications such as stationary power generation and small portable devices, transportation applications present some unique challenges for fuel cell technology. Due to their lower operating temperature and non-brittle materials, most transportation work is focusing on fuel cells using proton exchange membrane (PEM) technology. Since PEM fuel cells are fueled by hydrogen, major obstacles to their widespread use are the lack of an available hydrogen fueling infrastructure and hydrogen's relatively low energy storage density, which leads to a much lower driving range than conventional vehicles. One potential solution to the hydrogen infrastructure and storage density issues is to convert a conventional fuel such as gasoline into hydrogen onboard the vehicle using a fuel processor. Figure 2 shows that gasoline stores roughly 7 times more energy per volume than pressurized hydrogen gas at 700 bar and 4 times more than liquid hydrogen. If integrated properly, the fuel processor/fuel cell system would also be more efficient than traditional engines and would give a fuel economy benefit while hydrogen storage and distribution issues are being investigated. Widespread implementation of fuel processor/fuel cell systems requires improvements in several aspects of the technology, including size, startup time, transient response time, and cost. In addition, the ability to operate on a number of hydrocarbon fuels that are available through the existing infrastructure is a key enabler for commercializing these systems. In this program, Nuvera Fuel Cells collaborated with the Department of Energy (DOE) to develop efficient, low-emission, multi-fuel processors for transportation applications. Nuvera's focus was on (1) developing fuel

  13. Study over problems related to fuel and ash handling systems; Probleminventering braensle- och askhantering

    Energy Technology Data Exchange (ETDEWEB)

    Njurell, Rolf; Wikman, Karin [AaF-Energi och Miljoe AB, Stockhom (Sweden)

    2003-10-01

    There have been a lot of problems related to fuel and ash handling systems since the combustion of different types of biofuels started in the 70s. Many measures have been taken to solve some of the problems, but others have become part of the daily work. The purpose of this study has been to do a compilation of the fuel and ash handling problems that exist at different types of heat and power plants. The study over problems related to fuel and ash handling systems has been carried out through a questionnaire via the Internet. Directors at about 150 energy production plants were contacted by phone or e-mail in the beginning of the project and asked to participate in the study. 72 of these plants accepted to fill in the questionnaire. After several reminders by e-mails and phone calls there were in the end 32 plants that completed the form. Together they reported about 25 problems related to fuel handling and 27 problems related to ash handling. In general each of the plants reported one problem of each kind. Even if the material from the questionnaire is not enough to make statistical analysis a few conclusions can be made about the most common problems, the cause of the problems and where they appear. Fuel handling problems that occur at several plants are stoppage in the conveying equipment, bridging in the boiler silo or the tipping bunker and problems with the sieve for separation. The distribution of the fuel handling problems is almost equal for all equipment parts (receiving, separation, transport etc.). For the ash handling systems problems with transport of dry bottom ash dominate, followed by and the moistening of fly ash and transport of wet bottom ash. Most of the problems related to fuel handling are caused by the fuel quality. For example several plants have reported that bark is a fuel that is hard to handle. Nevertheless the quality for a specific fuel is not always bad when it is delivered to the plant but the fuel quality might change during

  14. Usage of Production Functions in the Comparative Analysis of Transport Related Fuel Consumption

    Directory of Open Access Journals (Sweden)

    Torok Adam

    2014-12-01

    Full Text Available This contribution aims to examine the relationship between the transport sector and the macroeconomy, particularly in fossil energy use, capital and labour relations. The authors have investigated the transport related fossil fuel consumption 2003 -2010 in a macroeconomic context in Hungary and Germany. The Cobb-Douglas type of production function could be justified empirically, while originating from the general CES (Constant Elasticity of Substitution production function. Furthermore, as a policy implication, the results suggest that a solution for the for the reduction of anthropogenic CO2 driven by the combustion of fossil fuels presupposes technological innovation to reach emission reduction targets. Other measures, such as increasing the fossil fuel price by levying taxes, would consequently lead to an undesirable GDP decline.

  15. Technical Meeting on Fast Reactors and Related Fuel Cycle Facilities with Improved Economic Characteristics. Working Material

    International Nuclear Information System (INIS)

    2013-01-01

    In recent years, engineering oriented work, rather than basic research and development (R&D), has led to significant progress in improving the economics of innovative fast reactors and associated fuel cycle facilities, while maintaining and even enhancing the safety features of these systems. Optimization of plant size and layout, more compact designs, reduction of the amount of plant materials and the building volumes, higher operating temperatures to attain higher generating efficiencies, improvement of load factor, extended core lifetimes, high fuel burnup, etc. are good examples of achievements to date that have improved the economics of fast neutron systems. The IAEA, through its Technical Working Group on Fast Reactors (TWG-FR) and Technical Working Group on Nuclear Fuel Cycle Options and Spent Fuel Management (TWG-NFCO), devotes many of its initiatives to encouraging technical cooperation and promoting common research and technology development projects among Member States with fast reactor and advanced fuel cycle development programmes, with the general aim of catalysing and accelerating technology advances in these fields. In particular the theme of fast reactor deployment, scenarios and economics has been largely debated during the recent IAEA International Conference on Fast Reactors and Related Fuel Cycles: Safe Technologies and Sustainable Scenarios, held in Paris in March 2013. Several papers presented at this conference discussed the economics of fast reactors from different national and regional perspectives, including business cases, investment scenarios, funding mechanisms and design options that offer significant capital and energy production cost reductions. This Technical Meeting on Fast Reactors and Related Fuel Cycle Facilities with Improved Economic Characteristics addresses Member States’ expressed need for information exchange in the field, with the aim of identifying the main open issues and launching possible initiatives to help and

  16. Risk connected to the demographic factors in managing labour relations in the tertiary sector of the economy

    Directory of Open Access Journals (Sweden)

    Aaliya Abdoolla

    2016-12-01

    Full Text Available In today’s fast-paced, competitive and digital work environment, the challenges of work commitments and personal responsibilities confront employers and employees. Employees want flexibility and control over their work obligations and their personal lives. This is imperative as their economic needs depend on the income derived from work performance. Employers need to institute relevant programmes for economic viability and sustainability. The study aims to examine the impact of the demographic variables on work-life balance in a tertiary sector of the economy. The study utilizes a questionnaire that was self-developed which was pilot tested and, the validity and reliability were determined. Significant differences surfaced in the study. The findings of the study shed light on balancing several aspects of employees’ work and family lives. The results culminate in recommendations for management to integrate Employee Assistance Programmes into its structure and policies; provide for on-site day care facilities and; institute flexible working practices to impact positively on employee commitment and motivation, amongst others

  17. The underground economy in Romania

    Directory of Open Access Journals (Sweden)

    Adriana Veronica LITRA

    2016-07-01

    Full Text Available The paper aims at covering issues related to the underground economy, activities that compound this phenomenon, its magnitude in Romania and reported to the European average. Underground economy in Romania consists of undeclared work (2/3 from the total and unreported income; it decreased from 33.6% of GDP in 2003 to 28% in 2014, but remained over EU-28 average with about 10 p.p. Among EU-28 countries, only Bulgaria exceeds the size of the underground economy of Romania. The underground economy is a challenge for the leadership of the state which must act simultaneously to stop illegal activities, and to discourage non-declaration of the legal activities. Corruption favours maintaining the underground economy, delays economic development, obstructs democratic processes and affects justice and the law state.

  18. Wind in the future hydrogen economy

    International Nuclear Information System (INIS)

    Andres, P.

    2006-01-01

    Converting to a hydrogen economy will only be sustainable and have a positive impact on the environment if the fuel source for the hydrogen production is from a renewable or GHG free fuel source. Wind energy is of particular interest as a potential energy source for hydrogen production. It is modular, abundant and competitive and is far from fully exploited around the globe. Transmission constraints are however the current bottle neck to fully exploiting this resource. Producing electrolytic hydrogen from wind energy in transmission constraint areas will allow for better utilization of the available wind energy and transmission resources. The type of hydrogen storage and transportation option chosen and the size of the facilities will be the crucial factors in determining the relative cost competitiveness of a wind / hydrogen facility verses traditional hydrogen production from fossil fuels. With fossil fuel prices at record highs and the traditional demand for hydrogen growing (oil refining, ammonia production) and the fact that the world has entered a GHG constraint era the need to explore large scale wind / hydrogen production facilities has never been more urgent. (author)

  19. 40 CFR 600.113-08 - Fuel economy calculations for FTP, HFET, US06, SC03 and cold temperature FTP tests.

    Science.gov (United States)

    2010-07-01

    ... (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method... Products by Hydrometer Method” for the blend. This incorporation by reference was approved by the Director... Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method” for the gasoline fuel...

  20. Relation between climate and diesel fuel rate consumption for sugar cane agriculture

    International Nuclear Information System (INIS)

    Fonte Hernandez, Aramis; Rivero Vega, Roger

    2005-01-01

    In the present work, some results are shown of a study carried out within the ENERCLIMA project. The principal objective was to establish the relationship between diesel fuel rate consumption by agricultural equipment in activities related to sugar cane production and simple climatic variables. Through a statistical analysis, we show the possibility of obtaining statistical models of an acceptable confidence level, as applied to some of these activities, which could be used in order to plan more rationally the level of fuel consumption of the agricultural companies with access to meteorological stations located nearby

  1. Application of a personal computer relational data base management system to fuel cycle economic scoping

    International Nuclear Information System (INIS)

    Malone, J.P.; Dooley, G.D.

    1986-01-01

    A personal computer (PC) relational data base management system (RDBMS) permits large quantities of data to be maintained in a data base composed of structured data sets or files and provides data access through a software environment, procedure, or program language. The features of an RDBMS-based system create an environment on a PC that can provide significant benefits to any fuel cycle economics analysis. The ability to maintain a separate data set for each fuel cycle parameter group and the ability to manipulate the data through a series of independent calculation modules combine to provide the fuel cycle analyst with more time to examine and use the data, because less time is required to manipulate it

  2. Fuel efficiency of conventional design tractors diesel engines in relation to new design

    Directory of Open Access Journals (Sweden)

    Jevtić Jeremija

    2006-01-01

    Full Text Available Total consumption of all types of energies is rather high nowadays with constant tendency of increasing. Transport section is one of the highest consumers of energy obtained from fossil fuels. It is absolutely clear that the reduction of energy consumption and the protection of environment - exhaust emission reduction, i. e. cleaner air, will be one of the main tasks of automotive industry in the first decades of the 21st century. In spite of its superiority over the petrol engine in respect of the fuel consumption, a diesel engine "suffers" from the increased exhaust emission, particles and NOx first of all and also from the noise and vibrations. The paper gives a review of fuel efficiency of conventional design tractors diesel engines in relation to new design. .

  3. Antimatter Economy

    Science.gov (United States)

    Hansen, Norm

    2004-05-01

    The Antimatter Economy will bring every country into the 21st century without destroying our environment and turn the Star Trek dream into reality by using antimatter from comets. At the April 2002 joint meeting of the American Physical Society and American Astronomical Society, I announced that comets were composed of antimatter, there were 109 antimatter elements, and the Periodic Table of Elements had been updated to include the antimatter elements. When matter and antimatter come together, energy is produce according to Einstein's equation of mass times the speed of light squared or E = mc2. Antimatter energy creates incredible opportunities for humanity. People in spacecraft will travel to the moon in hours, planets in days, and stars in weeks. Antimatter power will replace fossil plants and produce hydrogen from off-peak electrical power. Hydrogen will supplant gas in cars, trucks, and other vehicles. The billions of ton of coal, billions of barrels of oil, and trillions of cubic feet of natural gas will be used to make trillions of dollars of products to bring countries into the 21st century. Within this millennium, the Worlds Gross National Product will increase from 30 trillion to 3,000 trillion plus 1,500 trillion from space commercialization bringing the Total Gross National Product to 4,500 trillion. Millions of businesses and billions of jobs will be created. However, the real benefits will come from taking billions of people out of poverty and empowering them to pursue their dreams of life, liberty and pursuit of happiness. Please visit www.AntimatterEnergy.com.

  4. Fusion power economy of scale

    International Nuclear Information System (INIS)

    Dolan, T.J.

    1993-01-01

    In the next 50 yr, the world will need to develop hundreds of gigawatts of non-fossil-fuel energy sources for production of electricity and fuels. Nuclear fusion can probably provide much of the required energy economically, if large single-unit power plants are acceptable. Large power plants are more common than most people realize: There are already many multiple-unit power plants producing 2 to 5 GW(electric) at a single site. The cost of electricity (COE) from fusion energy is predicted to scale as COE ∼ COE 0 (P/P 0 ) -n , where P is the electrical power, the subscript zero denotes reference values, and the exponent n ∼ 0.36 to 0.7 in various designs. The validity ranges of these scalings are limited and need to be extended by future work. The fusion power economy of scale derives from four interrelated effects: improved operations and maintenance costs; scaling of equipment unit costs; a geometric effect that increases the mass power density; and reduction of the recirculating power fraction. Increased plasma size also relaxes the required confinement parameters: For the same neutron wall loading, larger tokamaks can use lower magnetic fields. Fossil-fuel power plants have a weaker economy of scale than fusion because the fuel costs constitute much of their COE. Solar and wind power plants consist of many small units, so they have little economy of scale. Fission power plants have a strong economy of scale but are unable to exploit it because the maximum unit size is limited by safety concerns. Large, steady-state fusion reactors generating 3 to 6 GW(electric) may be able to produce electricity for 4 to 5 cents/kW·h, which would be competitive with other future energy sources. 38 refs., 6 figs., 6 tabs

  5. Relative Release-to-Birth Indicators for Investigating TRISO Fuel Fission Gas Release Models

    International Nuclear Information System (INIS)

    Harp, Jason M.; Hawari, Ayman I.

    2008-01-01

    TRISO microsphere fuel is the fundamental fuel unit for Very High Temperature Reactors (VHTR). A single TRISO particle consists of an inner kernel of uranium dioxide or uranium oxycarbide surrounded by layers of pyrolytic carbon and silicon carbide. If the silicon carbide layer fails, fission products, especially the noble fission gases Kr and Xe, will begin to escape the failed particle. The release of fission gas is usually quantified by measuring the ratio of the released activity (R) to the original birth activity (B), which is designated as the R/B ratio. In this work, relative Release-to-Birth indicators (I) are proposed as a technique for interpreting the results of TRISO irradiation experiments. By implementing a relative metric, it is possible to reduce the sensitivity of the indicators to instrumental uncertainties and variations in experimental conditions. As an example, relative R/B indicators are applied to the interpretation of representative data from the Advanced Gas Reactor-1 TRISO fuel experiment that is currently taking place at the Advanced Test Reactor of Idaho National Laboratory. It is shown that the comparison of measured to predicted relative R/B indicators (I) gives insight into the physics of release and helps validate release models. Different trends displayed by the indicators are related to the mechanisms of fission gas release such as diffusion and recoil. The current analysis shows evidence for separate diffusion coefficients for Kr and Xe and supports the need to account for recoil release. (authors)

  6. Analysis of the holistic impact of the Hydrogen Economy on the coal industry

    Science.gov (United States)

    Lusk, Shannon Perry

    As gas prices soar and energy demand continues to grow amidst increasingly stringent environmental regulations and an assortment of global pressures, implementing alternative energy sources while considering their linked economic, environmental and societal impacts becomes a more pressing matter. The Hydrogen Economy has been proposed as an answer to meeting the increasing energy demand for electric power generation and transportation in an environmentally benign way. Based on current hydrogen technology development, the most practical feedstock to fuel the Hydrogen Economy may prove to be coal via hydrogen production at FutureGen plants. The planned growth of the currently conceived Hydrogen Economy will cause dramatic impacts, some good and some bad, on the economy, the environment, and society, which are interlinked. The goal of this research is to provide tools to inform public policy makers in sorting out policy options related to coal and the Hydrogen Economy. This study examines the impact of a transition to a Hydrogen Economy on the coal industry by creating FutureGen penetration models, forecasting coal MFA's which clearly provide the impact on coal production and associated environmental impacts, and finally formulating a goal programming model that seeks the maximum benefit to society while analyzing the trade-offs between environmental, social, and economical concerns related to coal and the Hydrogen Economy.

  7. Fuel assembly

    International Nuclear Information System (INIS)

    Ueda, Makoto; Ogiya, Shunsuke.

    1989-01-01

    For improving the economy of a BWR type reactor by making the operation cycle longer, the fuel enrichment degree has to be increased further. However, this makes the subcriticality shallower in the upper portion of the reactor core, to bring about a possibility that the reactor shutdown becomes impossible. In the present invention, a portion of fuel rod is constituted as partial length fuel rods (P-fuel rods) in which the entire stack length in the effective portion is made shorter by reducing the concentration of fissionable materials in the axial portion. A plurality of moderator rods are disposed at least on one diagonal line of a fuel assembly and P-fuel rods are arranged at a position put between the moderator rods. This makes it possible to reactor shutdown and makes the axial power distribution satisfactory even if the fuel enrichment degree is increased. (T.M.)

  8. Exploring the connections between green economy and informal economy in South Africa

    Directory of Open Access Journals (Sweden)

    Suzanne Smit

    2015-11-01

    Full Text Available The notion of an inclusive green economy in the context of sustainable development and poverty eradication requires an approach that engages with the informal economy. However, the informal economy is generally ignored or undervalued in discussions on the green economy. This paper set out to bolster this argument by identifying the ways in which the green economy and the informal economy may be connected by establishing the extent to which policies and plans relating to green economy connect with the informal economy, and recognising several informal green activities. The barriers and opportunities for connecting the two spheres were also explored as well as possible ways in which such activities may be supported at different levels of organisation. In the case of South Africa, many informal green activities that contribute to sustainable livelihoods are recognised. However, issues pertaining to procedure, process and participation hinder the transition to a truly inclusive green economy.

  9. Addressing Concerns Related to the Use of Ethanol-Blended Fuels in Marine Vehicles

    Directory of Open Access Journals (Sweden)

    Gregory W. Davis

    2017-12-01

    Full Text Available Ethanol blended fuels have become increasingly prevalent in the on-road transportation sector due to the benefits they provide in energy security, sustainability and reduced environmental impact. However, ethanol usage has led to material compatibility concerns causing corrosion and degradation in materials that are commonly used in engines and fuel storage/delivery systems. The on-road transportation sector continues to study and develop alternatives to minimize potential material challenges. Although, marine vehicles represent a smaller segment of the transportation sector, they represent many vehicles, particularly in the United States. Concerns related to the use of ethanol blended fuels in the marine environment have been expressed by many individuals and groups. Unfortunately, relatively little work has gone into the study of gasoline mixed with approximately 10% ethanol usage and potential material incompatibilities in marine engines. The objective of this article is to provide some factual answers to these concerns. In order to understand the extent of material incompatibilities, a literature survey of published material compatibility data and marine engine manufacturer recommendations was conducted. Next field samples of marine fuels were gathered to estimate the extent of ethanol usage in marine gasoline. Finally, samples of new and in-use marine components were exposed to either gasoline mixed with approximately 10% ethanol or gasoline with 0% ethanol for 1,960 hours to determine whether gasoline mixed with approximately 10% ethanol presented degradation beyond that seen with gasoline (gasoline with 0% ethanol alone. This work has shown that many marine engine manufacturers have used ethanol compatible materials in current products and that exposure of older marine engine components to gasoline mixed with approximately 10% ethanol by did not reveal any significant degradation. Finally, marine fuel samples gathered in 2013, reveal that

  10. Agri-food supply chains and sustainability-related issues: evidence from across the Scottish agri-food economy

    OpenAIRE

    Leat, Philip M.K.; Lamprinopoulou-Kranis, Chrysa; Revoredo-Giha, Cesar; Kupiec-Teahan, Beata

    2011-01-01

    This paper examines the influence of agri-food supply chains on the sustainability-related activities and decisions of Scottish farmers, as well as the treatment of sustainability issues by food processors and retailers themselves. It is based on 8 whole chain case studies covering some of Scotland’s major agricultural products. The cases identify differing levels of understanding and activities related to sustainability, but widespread acknowledgement that sustainability involves the develop...

  11. Reconceptualizing the nature and health consequences of work-related insecurity for the new economy: the decline of workers' power in the flexibility regime.

    Science.gov (United States)

    Scott, Heather K

    2004-01-01

    This article aims to reconceptualize job insecurity in a manner relevant to shifts in the power relations of work that have accompanied globalization, in order to assess the implications for workers' health. The linkage between job insecurity and health has been well established, but little formal theorizing has analyzed the mechanisms responsible. Implicitly, however, the assumption remains that its role as a stressor is limited to the realm of job strain, whereby workers lack control over a threatened employment situation. Within this framework, job insecurity and related dimensions of power remain locked in the "box" of the standard employment relationship, precluding an analysis of work-related insecurity in the new context of globalization. In contrast, the author constructs a model of work-related insecurity that takes into account current shifts in the balance of power toward employers, which in turn has undermined the fundamental quid pro quo associated with the standard postwar model of employment. She proposes that job insecurity is no longer a mere temporary break in an otherwise predictable work-life pattern but rather a structural feature of the new labor market. Emerging contingencies associated with the New Economy, "flexibilized" employment relationships, and diminution of workers' power have constituted work-related insecurity as a chronic stressor with several implications for long-term health outcomes at the individual and societal levels.

  12. Estimates of relative areas for the disposal in bedded salt of LWR wastes from alternative fuel cycles

    International Nuclear Information System (INIS)

    Lincoln, R.C.; Larson, D.W.; Sisson, C.E.

    1978-01-01

    The relative mine-level areas (land use requirements) which would be required for the disposal of light-water reactor (LWR) radioactive wastes in a hypothetical bedded-salt formation have been estimated. Five waste types from alternative fuel cycles have been considered. The relative thermal response of each of five different site conditions to each waste type has been determined. The fuel cycles considered are the once-through (no recycle), the uranium-only recycle, and the uranium and plutonium recycle. The waste types which were considered include (1) unreprocessed spent reactor fuel, (2) solidified waste derived from reprocessing uranium oxide fuel, (3) plutonium recovered from reprocessing spent reactor fuel and doped with 1.5% of the accompanying waste from reprocessing uranium oxide fuel, (4) waste derived from reprocessing mixed uranium/plutonium oxide fuel in the third recycle, and (5) unreprocessed spent fuel after three recycles of mixed uranium/plutonium oxide fuels. The relative waste-disposal areas were determined from a calculated value of maximum thermal energy (MTE) content of the geologic formations. Results are presented for each geologic site condition in terms of area ratios. Disposal area requirements for each waste type are expressed as ratios relative to the smallest area requirement (for waste type No. 2 above). For the reference geologic site condition, the estimated mine-level disposal area ratios are 4.9 for waste type No. 1, 4.3 for No. 3, 2.6 for No. 4, and 11 for No. 5

  13. CRP on Demonstrating Performance of Spent Fuel and Related Storage Systems beyond the Long Term

    International Nuclear Information System (INIS)

    Bevilacqua, Arturo

    2014-01-01

    At the initial Coordinated Research Project (CRP) planning meeting held in August 2011, international experts in spent fuel performance confirmed the value of further coordination and development of international efforts to demonstrate the performance of spent fuel and related storage system components as durations extend. Furthermore, in recognition that the Extended Storage Collaboration Program (ESCP) managed by the Electric Power Research Institute (EPRI) in the USA, from now on ESCP, provided a broad context for the research and development work to be performed in the frame of this CRP, it was agreed that its objectives should target specific ESCP needs in order to make a relevant contribution. Accordingly, the experts examined on-going gap analyses - gaps between anticipated technical needs and existing technical data - for identify the specific research objectives. Additionally, during the planning meeting it was pointed out the need to coordinate and cooperate with the OECD/NEA counterparts involved in the organization of the International Workshop planned in autumn 2013 and with the on-going third phase of the CRP on Spent Fuel Performance Assessment and Research (SPAR-III). Given the importance to assess the performance of spent fuel and related important storage system components in order to confirm the viability of very long term storage for supporting the need to extend or renew licenses for storage facilities the CRP was approved by the IAEA in November 2011. While a full range of spent fuel types and storage conditions are deployed around the world, this CRP is focused on existing systems and, more specifically, water reactor fuel in dry storage with the overall research objective to support the technical basis for water reactor spent fuel management as dry storage durations extend. In March 2012 the group of international experts who participated at the initial CRP planning meeting in August 2011 evaluated and recommended for approval 9 research

  14. Electricity prices and fuel costs. Long-run relations and short-run dynamics

    International Nuclear Information System (INIS)

    Mohammadi, Hassan

    2009-01-01

    The paper examines the long-run relation and short-run dynamics between electricity prices and three fossil fuel prices - coal, natural gas and crude oil - using annual data for the U.S. for 1960-2007. The results suggest (1) a stable long-run relation between real prices for electricity and coal (2) Bi-directional long-run causality between coal and electricity prices. (3) Insignificant long-run relations between electricity and crude oil and/or natural gas prices. And (4) no evidence of asymmetries in the adjustment of electricity prices to deviations from equilibrium. A number of implications are addressed. (author)

  15. Ethanol, Corn, and Soybean Price Relations in a Volatile Vehicle-Fuels Market

    Directory of Open Access Journals (Sweden)

    Cesar Escalante

    2009-06-01

    Full Text Available The rapid upward shift in ethanol demand has raised concerns about ethanol’s impact on the price level and volatility of agricultural commodities. The popular press attributes much of this volatility in commodity prices to a price bubble in ethanol fuel and recent deflation. Market economics predicts not only a softening of demand to high commodity prices but also a positive supply response. This volatility in ethanol and commodity prices are investigated using cointegration, vector error corrections (VECM, and multivariate generalized autoregressive conditional heteroskedascity (MGARCH models. In terms of derived demand theory, results support ethanol and oil demands as derived demands from vehicle-fuel production. Gasoline prices directly influence the prices of ethanol and oil. However, of greater significance for the fuel versus food security issue, results support the effect of agricultural commodity prices as market signals which restore commodity markets to their equilibriums after a demand or supply event (shock. Such shocks may in the short-run increase agricultural commodity prices, but decentralized freely operating markets will mitigate the persistence of these shocks. Results indicate in recent years there are no long-run relations among fuel (ethanol, oil and gasoline prices and agricultural commodity (corn and soybean prices.

  16. Analysis of economy characteristics and improvement ways for China nuclear power

    International Nuclear Information System (INIS)

    Li Yong

    2010-01-01

    For the nuclear power industry, due to characteristics of its own, its economy is quite different from that of the traditional fossil-fuel power. This paper studied the basic characteristics of the nuclear power economy and the status of economy of domestic nuclear power, and analyzed the main ways to improve the nuclear power economy. (authors)

  17. Hunter-gatherer postcranial robusticity relative to patterns of mobility, climatic adaptation, and selection for tissue economy.

    Science.gov (United States)

    Stock, J T

    2006-10-01

    Human skeletal robusticity is influenced by a number of factors, including habitual behavior, climate, and physique. Conflicting evidence as to the relative importance of these factors complicates our ability to interpret variation in robusticity in the past. It remains unclear how the pattern of robusticity in the skeleton relates to adaptive constraints on skeletal morphology. This study investigates variation in robusticity in claviculae, humeri, ulnae, femora, and tibiae among human foragers, relative to climate and habitual behavior. Cross-sectional geometric properties of the diaphyses are compared among hunter-gatherers from southern Africa (n = 83), the Andaman Islands (n = 32), Tierra del Fuego (n = 34), and the Great Lakes region (n = 15). The robusticity of both proximal and distal limb segments correlates negatively with climate and positively with patterns of terrestrial and marine mobility among these groups. However, the relative correspondence between robusticity and these factors varies throughout the body. In the lower limb, partial correlations between polar second moment of area (J(0.73)) and climate decrease from proximal to distal section locations, while this relationship increases from proximal to distal in the upper limb. Patterns of correlation between robusticity and mobility, either terrestrial or marine, generally increase from proximal to distal in the lower and upper limbs, respectively. This suggests that there may be a stronger relationship between observed patterns of diaphyseal hypertrophy and behavioral differences between populations in distal elements. Despite this trend, strength circularity indices at the femoral midshaft show the strongest correspondence with terrestrial mobility, particularly among males.

  18. CANDU fuel cycle options in Korea

    International Nuclear Information System (INIS)

    Boczar, P. G.; Fehrenbach, P. J.; Meneley, D. A.

    1996-01-01

    There are many reasons for countries embarking on a CANDU R program to start with the natural uranium fuel cycle. Simplicity of fuel design, ease of fabrication, and ready availability of natural uranium all help to localize the technology and to reduce reliance on foreign technology. Nonetheless, at some point, the incentives for using natural uranium fuel may be outweighed by the advantages of alternate fuel cycles. The excellent neutron economy, on-line refuelling, and simple fuel-bundle design provide an unsurpassed degree of fuel-cycle flexibility in CANDU reactors. The easiest first step in CANDU fuel-cycle evolution may be the use of slightly enriched uranium (SEU), including recovered uranium from reprocessed LWR spent fuel. Relatively low enrichment (up to 1.2%) will result in a two- to three-fold reduction in the quantity of spent fuel per unit energy production, reductions in fuel-cycle costs, and greater flexibility in the design of new reactors. The CANFLEX (CANDU FLEXible) fuel bundle would be the optimal fuel carrier. A country that has both CANDU and PWR reactors can exploit the natural synergism between these two reactor types to minimize overall waste production, and maximize energy derived from the fuel. This synergism can be exploited through several different fuel cycles. A high burnup CANDU MOX fuel design could be used to utilize plutonium from conventional reprocessing or more advanced reprocessing options (such as co-processing). DUPIC (Direct Use of Spent PWR Fuel In CANDU) represents a recycle option that has a higher degree of proliferation resistance than dose conventional reprocessing, since it uses only dry processes for converting spent PWR fuel into CANDU fuel, without separating the plutonium. Good progress is being made in the current KAERI, AECL, and U. S. Department of State program in demonstrating the technical feasibility of DUPIC. In the longer term, CANDU reactors offer even more dramatic synergistic fuel cycles with PWR or

  19. International conference on fast reactors and related fuel cycles (FR09): Challenges and opportunities. CN-176 presentations

    International Nuclear Information System (INIS)

    2009-01-01

    Renewed interest in nuclear energy is driven by the need to develop carbon free energy sources, by demographics and development in emerging economies, as well as by security of supply concerns. It is expected that nuclear energy will deliver huge amounts of energy to both emerging and developed economies. However, acceptance of large scale contributions would depend on satisfaction of key drivers to enhance sustainability in terms of economics, safety, adequacy of natural resources, waste reduction, non-proliferation and public acceptance. Fast spectrum reactors with recycle enhance the sustainability indices significantly. This has led to the focus on fast spectrum reactors with recycle in the Generation IV International Forum (GIF) and the International Project on Innovative Nuclear Reactors and Fuel Cycles (INPRO) initiative of the IAEA. It is expected that 2009 will register major events in the domain of fast spectrum reactors, that is, the restart of Monju in Japan, the first criticality of the China Experimental Fast Reactor in China, as well as new insights through end-of-life studies in Phenix, France. New fast reactors are expected to be commissioned in the near future: the 500 MW(e) Prototype Fast Breeder Reactor in India and the BN-800 unit in the Russian Federation. Moreover, China, France, India, Japan, Republic of Korea and the United States of America are preparing advanced prototypes/ demonstrations and/or commercial reactors for the 2020-2030 horizon. The necessary condition for successful fast reactor deployment in the near and mid-term is the understanding and assessment of innovative technological and design options, based on both past knowledge and experience, as well as on ongoing research and technology development efforts. In this respect, the need for in-depth international information exchange is underscored by the fact that the last large international fast reactor conference was held as far back as 1991. Since then, progress in research

  20. Assessment of methane-related fuels for automotive fleet vehicles: technical, supply, and economic assessments

    Energy Technology Data Exchange (ETDEWEB)

    1982-02-01

    The use of methane-related fuels, derived from a variety of sources, in highway vehicles is assessed. Methane, as used here, includes natural gas (NG) as well as synthetic natural gas (SNG). Methanol is included because it can be produced from NG or the same resources as SNG, and because it is a liquid fuel at normal ambient conditions. Technological, operational, efficiency, petroleum displacement, supply, safety, and economic issues are analyzed. In principle, both NG and methanol allow more efficient engine operation than gasoline. In practice, engines are at present rarely optimized for NG and methanol. On the basis of energy expended from resource extraction to end use, only optimized LNG vehicles are more efficient than their gasoline counterparts. By 1985, up to 16% of total petroleum-based highway vehicle fuel could be displaced by large fleets with central NG fueling depots. Excluding diesel vehicles, which need technology advances to use NG, savings of 8% are projected. Methanol use by large fleets could displace up to 8% of petroleum-based highway vehicle fuel from spark-ignition vehicles and another 9% from diesel vehicles with technology advances. The US NG supply appears adequate to accommodate fleet use. Supply projections, future price differential versus gasoline, and user economics are uncertain. In many cases, attractive paybacks can occur. Compressed NG now costs on average about $0.65 less than gasoline, per energy-equivalent gallon. Methanol supply projections, future prices, and user economics are even more uncertain. Current and projected near-term methanol supplies are far from adequate to support fleet use. Methanol presently costs more than gasoline on an equal-energy basis, but is projected to cost less if produced from coal instead of NG or petroleum.

  1. Disease burden due to biomass cooking-fuel-related household air pollution among women in India.

    Science.gov (United States)

    Sehgal, Meena; Rizwan, Suliankatchi Abdulkader; Krishnan, Anand

    2014-01-01

    Household air pollution (HAP) due to biomass cooking fuel use is an important risk factor for a range of diseases, especially among adult women who are primary cooks, in India. About 80% of rural households in India use biomass fuel for cooking. The aim of this study is to estimate the attributable cases (AC) for four major diseases/conditions associated with biomass cooking fuel use among adult Indian women. We used the population attributable fraction (PAF) method to calculate the AC of chronic bronchitis, tuberculosis (TB), cataract, and stillbirths due to exposure to biomass cooking fuel. A number of data sources were accessed to obtain population totals and disease prevalence rates. A meta-analysis was conducted to obtain adjusted pooled odds ratios (ORs) for strength of association. Using this, PAF and AC were calculated using a standard formula. Results were presented as number of AC and 95% confidence intervals (CI). The fixed effects pooled OR obtained from the meta-analysis were 2.37 (95% CI: 1.59, 3.54) for chronic bronchitis, 2.33 (1.65, 3.28) for TB, 2.16 (1.42, 3.26) for cataract, and 1.26 (1.12, 1.43) for stillbirths. PAF varied across conditions being maximum (53%) for chronic bronchitis in rural areas and least (1%) for cataract in older age and urban areas. About 2.4 (95% CI: 1.4, 3.1) of 5.6 m cases of chronic bronchitis, 0.3 (0.2, 0.4) of 0.76 m cases of TB, 5.0 (2.8, 6.7) of 51.4 m cases of cataract among adult Indian women and 0.02 (0.01, 0.03) of 0.15 m stillbirths across India are attributable to HAP due to biomass cooking fuel. These estimates should be cautiously interpreted in the light of limitations discussed which relate to exposure assessment, exposure characterization, and age-specific prevalence of disease. HAP due to biomass fuel has diverse and major impacts on women's health in India. Although challenging, incorporating the agenda of universal clean fuel access or cleaner technology within the broader framework of rural

  2. Safety assessments relating to the use of new fuels in research reactors: application to the case of FRM 2 reactor fuel

    International Nuclear Information System (INIS)

    Abou Yehia, H.; Bars, G.; Tran Dai

    2001-01-01

    After giving a brief reminder of the procedure applied in France for the licensing of the use of a new fuel type or design in a research reactor, we outline the main safety aspects associated with such a modification. Finally, by way of an example, we focus on the safety assessment relating to the IRIS irradiation device used in SILOE reactor, in particular for the qualification of the fuel dedicated to FRM II reactor of the Technical University of Munich. This qualification was carried out on a U 3 Si 2 fuel plate enriched to about 90 % in weight of 235 U and containing 1.5 g of uranium per cm 3 . The evaluation performed by the IPSN for GRS did not call into question the choice of U 3 Si 2 fuel plates for the FRM-II reactor. (authors)

  3. A nuclear based hydrogen economy

    International Nuclear Information System (INIS)

    Sandquist, G.M.; Tamm, G.; Kunze, J.

    2005-01-01

    Exhausting demands are being imposed upon the world's ability to extract and deliver oil to the nations demanding fluid fossil fuels. This paper analyzes these issues and concludes that there must be no delay in beginning the development of the 'hydrogen economy' using nuclear energy as the primary energy source to provide both the fluid fuel and electrical power required in the 21st century. Nuclear energy is the only proven technology that is abundant and available worldwide to provide the primary energy needed to produce adequate hydrogen fluid fuel supplies to replace oil. Most importantly, this energy transition can be accomplished in an economical and technically proven manner while lowering greenhouse gas emissions. Furthermore, a similar application of using wind and solar to produce hydrogen instead of electricity for the grid can pave the way for the much larger production scales of nuclear plants producing both electricity and hydrogen. (authors)

  4. IMPACTT5A model : enhancements and modifications since December 1994 with special reference to the effect of tripled-fuel-economy vehicles on fuel-cycle energy and emissions

    Science.gov (United States)

    1998-09-01

    Version 5A of the Integrated Market Penetration and Anticipated Cost of Transportation Technologies (IMPACIT5A) model is a spreadsheet-based set of algorithms that calculates the effects of advanced-technology vehicles on baseline fuel use and emi...

  5. THEN: COE-INES international workshop on 'toward hydrogen economy; what nuclear can contribute and how'. Proposal and presentations

    International Nuclear Information System (INIS)

    2005-01-01

    The workshop of the title was held on topics; hydrogen system, nuclear and non-nuclear hydrogen production, hydrogen storage and transportation, fuel-cells, hydrogen energy management, hydrogen economy and all subjects related on hydrogen system, consisted of 4 panels by 15 panelists and a comprehensive discussion session. (J.P.N.)

  6. An optimized BWR fuel lattice for improved fuel utilization

    International Nuclear Information System (INIS)

    Bernander, O.; Helmersson, S.; Schoen, C.G.

    1984-01-01

    Optimization of the BWR fuel lattice has evolved into the water cross concept, termed ''SVEA'', whereby the improved moderation within bundles augments reactivity and thus improves fuel cycle economy. The novel design introduces into the assembly a cruciform and double-walled partition containing nonboiling water, thus forming four subchannels, each of which holds a 4x4 fuel rod bundle. In Scandinavian BWRs - for which commercial SVEA reloads are now scheduled - the reactivity gain is well exploited without adverse impact in other respects. In effect, the water cross design improves both mechanical and thermal-hydraulic performance. Increased average burnup is also promoted through achieving flatter local power distributions. The fuel utilization savings are in the order of 10%, depending on the basis of comparison, e.g. choice of discharge burnup and lattice type. This paper reviews the design considerations and the fuel utilization benefits of the water cross fuel for non-Scandinavian BWRs which have somewhat different core design parameters relative to ASEA-ATOM reactors. For one design proposal, comparisons are made with current standard 8x8 fuel rod bundles as well as with 9x9 type fuel in reactors with symmetric or asymmetric inter-assembly water gaps. The effect on reactivity coefficients and shutdown margin are estimated and an assessment is made of thermal-hydraulic properties. Consideration is also given to a novel and advantageous way of including mixed-oxide fuel in BWR reloads. (author)

  7. Linking Indigenous Peoplesr Health-Related Decision Making to Information Communication Technology: Insights from an Emerging Economy

    Directory of Open Access Journals (Sweden)

    Md. Jahir Uddin Palas

    2017-04-01

    Full Text Available Indigenous peoples are being marginalised globally from a socioeconomic perspective and are often excluded from mainstream communities for social and/or geographic reasons. Historically, they tend to have lower living standards, including poor health conditions as compared to the rest of the population. Literature suggests that information and communication technologies (ICTs have the potential to improve awareness about how to improve health and wellbeing. In order to both deepen and broaden the understanding of how ICTs can influence Indigenous peoplesr health-related decision-making, this study has developed a conceptual framework based on the capability approach, focusing on the five dimensions of freedoms suggested by Amartya Sen. Data collected from a sample of members of an Indigenous community in Bangladesh, using a purposive sampling method, were analysed through qualitative techniques to identify ways in which a mobile-based health system have influenced the lives of indigenous people. The findings revealed that the mobile healthcare system explored in this study addressed a number of factors pertaining to indigenous peoplesr quality of life. These findings are useful for policy formulation related to the design and implementation of healthcare strategies in Bangladesh. The conceptual framework, following further validation, could serve as a platform for the advancement of research towards understanding how mobile healthcare systems can improve the wellbeing of individuals in indigenous communities.

  8. Professional Networks in the International Political Economy

    DEFF Research Database (Denmark)

    Henriksen, Lasse Folke; Seabrooke, Leonard

    debates; and the creation of ‘human capital controls’ to prevent the poaching of skilled migrants. The paper directly contributes to the STS literature in locating how professional practices and, their work content, are linked to science and technology while embedded in sociocultural frameworks......Who writes the rules for the governance of the world economy? This paper looks beyond the usual suspects of states, NGOs and firms to attempt to map how ideas and skills travel between professional ecologies to solve long-term socioeconomic problems. The paper identifies professional networks...... they compete and cooperate through a variety of novel concepts and technologies. The issue-areas discussed in relation to professional networks include: the creation of a viable bio-fuels industry; addressing low fertility rates in the OECD; risk weighting and regulatory segmentation in financial reform...

  9. Waste to chemicals for a circular economy.

    Science.gov (United States)

    Iaquaniello, Gaetano; Centi, Gabriele; Annarita Salladini, Annarita; Palo, Emma; Perathoner, Siglinda

    2018-06-25

    The implementation of a circular economy is a fundamental step to create a greater and more sustainable future for a better use of resources and energy. Wastes and in particular municipal solid waste represent an untapped source of carbon (and hydrogen) to produce a large range of chemicals from methane to alcohols (as methanol or ethanol) or urea. The waste to chemical (WtC) process and related economics are assessed in this concept article to show the validity of such solution both from an economic point of view and from an environmental perspective considering the sensible reduction in greenhouse gas emissions with respect to conventional production from fossil fuels. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Nuclear regulatory guides for LWR (PWR) fuel in Japan and some related safety research

    International Nuclear Information System (INIS)

    Ichikawa, M.

    1994-01-01

    The general aspects of licensing procedure for NPPs in Japan and regulatory guides are described. The expert committee reports closely related to PWR fuel are reviewed. Some major results of reactor safety research experiments at NSPR (Nuclear Safety Research Reactor of JAERI) used for establishment of related guide, are discussed. It is pointed out that the reactor safety research in Japan supports the regularity activities by establishing and revising guides and preparing the necessary regulatory data as well as improving nuclear safety. 10 figs., 4 refs

  11. Nuclear regulatory guides for LWR (PWR) fuel in Japan and some related safety research

    Energy Technology Data Exchange (ETDEWEB)

    Ichikawa, M [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan)

    1994-12-31

    The general aspects of licensing procedure for NPPs in Japan and regulatory guides are described. The expert committee reports closely related to PWR fuel are reviewed. Some major results of reactor safety research experiments at NSPR (Nuclear Safety Research Reactor of JAERI) used for establishment of related guide, are discussed. It is pointed out that the reactor safety research in Japan supports the regularity activities by establishing and revising guides and preparing the necessary regulatory data as well as improving nuclear safety. 10 figs., 4 refs.

  12. Fuel chemistry and pellet-clad interaction related to high burnup fuel. Proceedings of the technical committee

    International Nuclear Information System (INIS)

    2000-10-01

    The purpose of the meeting was to review new developments in clad failures. Major findings regarding the causes of clad failures are presented in this publication, with the main topics being fuel chemistry and fission product behaviour, swelling and pellet-cladding mechanical interaction, cladding failure mechanism at high burnup, thermal properties and fuel behaviour in off-normal conditions. This publication contains 17 individual presentations delivered at the meeting; each of them was indexed separately

  13. Methodology for the calculation of source terms related to irradiated fuel accumulated away from nuclear power plants

    International Nuclear Information System (INIS)

    Lima Filho, R.M.; Oliveira, L.F.S. de

    1984-01-01

    A general method for the calculation of the time evolution of source terms related to irradiated fuel is presented. Some applications are discussed which indicated that the method can provide important informations for the engineering design and safety analysis of a temporary storage facility of irradiated fuel elements. (Author) [pt

  14. Opening Address [International Conference on Fast Reactors and Related Fuel Cycles: Safe Technologies and Sustainable Scenarios (FR13), Paris, France, March 4-7, 2013

    International Nuclear Information System (INIS)

    Amano, Yukiya

    2013-01-01

    Public confidence in nuclear power was greatly shaken by the Fukushima Daiichi accident. It will take time to rebuild that confidence. This will only be possible if everyone involved in nuclear power has a total commitment to safety and if the sector is open and transparent. The public need to be reassured that nuclear energy is efficient and safe, can mitigate the effects of climate change and can play a key role in meeting the growing global demand for energy. Fast reactors and related fuel cycles will be important for the long-term sustainability of nuclear power. This innovative technology has the potential to ensure that energy resources which would run out in a few hundred years, using today’s technology, will actually last several thousand years. Fast reactors also reduce the volume and toxicity of the final waste. China’s Experimental Fast Reactor has been connected to the grid. Work is at an advanced stage on construction of India’s 500 MW(e) Prototype Fast Breeder Reactor and of the large BN-800 reactor in the Russian Federation. Interest in fast reactors with closed fuel cycles is increasing steadily. A number of emerging economies are joining the existing fast reactor technology-holders. Considerable R & D work is being done on advanced designs with enhanced safety characteristics. It is important to gather the operational experience of countries with operating fast reactors and related fuel cycle facilities. This can help to achieve higher levels of safety. Events such as the Joint GIF-IAEA Workshop on the safety of sodium-cooled fast reactors last week are a useful way of doing this. They also help to ensure that relevant lessons from the Fukushima Daiichi accident are learned. The IAEA remains the unique collaboration forum for ensuring continued progress in fast reactor technology. We provide an umbrella for knowledge preservation, information exchange and collaborative R&D in which resources and expertise are pooled

  15. Determination of Basic Structure-Property Relations for Processing and Modeling in Advanced Nuclear Fuel: Microstructure Evolution and Mechanical Properties

    International Nuclear Information System (INIS)

    Wheeler, Kirk; Parra, Manuel; Peralta, Pedro

    2009-01-01

    The project objective is to study structure-property relations in solid solutions of nitrides and oxides with surrogate elements to simulate the behavior of fuels of inert matrix fuels of interest to the Advanced Fuel Cycle Initiative (AFCI), with emphasis in zirconium-based materials. Work with actual fuels will be carried out in parallel in collaboration with Los Alamos National Laboratory (LANL). Three key aspects will be explored: microstructure characterization through measurement of global texture evolution and local crystallographic variations using Electron Backscattering Diffraction (EBSD); determination of mechanical properties, including fracture toughness, quasi-static compression strength, and hardness, as functions of load and temperature, and, finally, development of structure-property relations to describe mechanical behavior of the fuels based on experimental data. Materials tested will be characterized to identify the mechanisms of deformation and fracture and their relationship to microstructure and its evolution. New aspects of this research are the inclusion of crystallographic information into the evaluation of fuel performance and the incorporation of statistical variations of microstructural variables into simplified models of mechanical behavior of fuels that account explicitly for these variations. The work is expected to provide insight into processing conditions leading to better fuel performance and structural reliability during manufacturing and service, as well as providing a simplified testing model for future fuel production

  16. Fuel assemblies

    International Nuclear Information System (INIS)

    Nagano, Mamoru; Yoshioka, Ritsuo

    1983-01-01

    Purpose: To effectively utilize nuclear fuels by increasing the reactivity of a fuel assembly and reduce the concentration at the central region thereof upon completion of the burning. Constitution: A fuel assembly is bisected into a central region and a peripheral region by disposing an inner channel box within a channel box. The flow rate of coolants passing through the central region is made greater than that in the peripheral region. The concentration of uranium 235 of the fuel rods in the central region is made higher. In such a structure, since the moderating effect in the central region is improved, the reactivity of the fuel assembly is increased and the uranium concentration in the central region upon completion of the burning can be reduced, fuel economy and effective utilization of uranium can be attained. (Kamimura, M.)

  17. Fuel assembly

    International Nuclear Information System (INIS)

    Yokota, Tokunobu.

    1990-01-01

    A fuel assembly used in a FBR type nuclear reactor comprises a plurality of fuel rods and a moderator guide member (water rod). A moderator exit opening/closing mechanism is formed at the upper portion of the moderator guide member for opening and closing a moderator exit. In the initial fuel charging operation cycle to the reactor, the moderator exit is closed by the moderator exit opening/closing mechanism. Then, voids are accumulated at the inner upper portion of the moderator guide member to harden spectrum and a great amount of plutonium is generated and accumulated in the fuel assembly. Further, in the fuel re-charging operation cycle, the moderator guide member is used having the moderator exit opened. In this case, voids are discharged from the moderator guide member to decrease the ratio, and the plutonium accumulated in the initial charging operation cycle is burnt. In this way, the fuel economy can be improved. (I.N.)

  18. Fuel spacer

    International Nuclear Information System (INIS)

    Nishida, Koji; Yokomizo, Osamu; Kanazawa, Toru; Kashiwai, Shin-ichi; Orii, Akihito.

    1992-01-01

    The present invention concerns a fuel spacer for a fuel assembly of a BWR type reactor and a PTR type reactor. Springs each having a vane are disposed on the side surface of a circular cell which supports a fuel rods. A vortex streams having a vertical component are formed by the vanes in the flowing direction of a flowing channel between adjacent cylindrical cells. Liquid droplets carried by streams are deposited on liquid membrane streams flowing along the fuel rod at the downstream of the spacer by the vortex streams. In view of the above, the liquid droplets can be deposited to the fuel rod without increasing the amount of metal of the spacer. Accordingly, the thermal margin of the fuel assembly can be improved without losing neutron economy. (I.N.)

  19. Alternative Fuels DISI Engine Research ? Autoignition Metrics.

    Energy Technology Data Exchange (ETDEWEB)

    Sjoberg, Carl Magnus Goran [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Vuilleumier, David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2018-02-01

    Improved engine efficiency is required to comply with future fuel economy standards. Alternative fuels have the potential to enable more efficient engines while addressing concerns about energy security. This project contributes to the science base needed by industry to develop highly efficient direct injection spark igniton (DISI) engines that also beneficially exploit the different properties of alternative fuels. Here, the emphasis is on quantifying autoignition behavior for a range of spark-ignited engine conditions, including directly injected boosted conditions. The efficiency of stoichiometrically operated spark ignition engines is often limited by fuel-oxidizer end-gas autoignition, which can result in engine knock. A fuel’s knock resistance is assessed empirically by the Research Octane Number (RON) and Motor Octane Number (MON) tests. By clarifying how these two tests relate to the autoignition behavior of conventional and alternative fuel formulations, fuel design guidelines for enhanced engine efficiency can be developed.

  20. Real-time immune-inspired optimum state-of-charge trajectory estimation using upcoming route information preview and neural networks for plug-in hybrid electric vehicles fuel economy

    Science.gov (United States)

    Mozaffari, Ahmad; Vajedi, Mahyar; Azad, Nasser L.

    2015-06-01

    The main proposition of the current investigation is to develop a computational intelligence-based framework which can be used for the real-time estimation of optimum battery state-of-charge (SOC) trajectory in plug-in hybrid electric vehicles (PHEVs). The estimated SOC trajectory can be then employed for an intelligent power management to significantly improve the fuel economy of the vehicle. The devised intelligent SOC trajectory builder takes advantage of the upcoming route information preview to achieve the lowest possible total cost of electricity and fossil fuel. To reduce the complexity of real-time optimization, the authors propose an immune system-based clustering approach which allows categorizing the route information into a predefined number of segments. The intelligent real-time optimizer is also inspired on the basis of interactions in biological immune systems, and is called artificial immune algorithm (AIA). The objective function of the optimizer is derived from a computationally efficient artificial neural network (ANN) which is trained by a database obtained from a high-fidelity model of the vehicle built in the Autonomie software. The simulation results demonstrate that the integration of immune inspired clustering tool, AIA and ANN, will result in a powerful framework which can generate a near global optimum SOC trajectory for the baseline vehicle, that is, the Toyota Prius PHEV. The outcomes of the current investigation prove that by taking advantage of intelligent approaches, it is possible to design a computationally efficient and powerful SOC trajectory builder for the intelligent power management of PHEVs.

  1. UNDERGROUND ECONOMY, INFLUENCES ON NATIONAL ECONOMIES

    Directory of Open Access Journals (Sweden)

    CEAUȘESCU IONUT

    2015-04-01

    Full Text Available The purpose of research is to improve the understanding of nature underground economy by rational justification of the right to be enshrined a reality that, at least statistically, can no longer be neglected. So, we propose to find the answer to the question: has underground economy to stand-alone?

  2. Symbiotic N2 fixation activity in relation to C economy of Pisum sativum L. as a function of plant phenology.

    Science.gov (United States)

    Voisin, A S; Salon, C; Jeudy, C; Warembourg, F R

    2003-12-01

    The relationships between symbiotic nitrogen fixation (SNF) activity and C fluxes were investigated in pea plants (Pisum sativum L. cv. Baccara) using simultaneous 13C and 15N labelling. Analysis of the dynamics of labelled CO2 efflux from the nodulated roots allowed the different components associated with SNF activity to be calculated, together with root and nodule synthetic and maintenance processes. The carbon costs for the synthesis of roots and nodules were similar and decreased with time. Carbon lost by turnover, associated with maintenance processes, decreased with time for nodules while it increased in the roots. Nodule turnover remained higher than root turnover until flowering. The effect of the N source on SNF was investigated using plants supplied with nitrate or plants only fixing N2. SNF per unit nodule biomass (nodule specific activity) was linearly related to the amount of carbon allocated to the nodulated roots regardless of the N source, with regression slopes decreasing across the growth cycle. These regression slopes permitted potential values of SNF specific activity to be defined. SNF activity decreased as the plants aged, presumably because of the combined effects of both increasing C costs of SNF (from 4.0 to 6.7 g C g-1 N) and the limitation of C supply to the nodules. SNF activity competed for C against synthesis and maintenance processes within the nodulated roots. Synthesis was the main limiting factor of SNF, but its importance decreased as the plant aged. At seed-filling, SNF was probably more limited by nodule age than by C supply to the nodulated roots.

  3. Review of Sodium and Plutonium related Technical Standards in Trans-Uranium Fuel Fabrication Facilities

    International Nuclear Information System (INIS)

    Jang, Misuk; Jeon, Jong Seon; Kang, Hyun Sik; Kim, Seoung Rae

    2016-01-01

    In this paper, we would introduce and review technical standards related to sodium fire and plutonium criticality safety. This paper may be helpful to identify considerations in the development of equipment, standards, and etc., to meet the safety requirements in the design, construction and operating of TFFF, KAPF and SFR. The feasibility and conceptual designs are being examined on related facilities, for example, TRU Fuel Fabrication Facilities (TFFF), Korea Advanced Pyro-process Facility (KAPF), and Sodium Cooled Fast Reactor (SFR), in Korea. However, the safety concerns of these facilities have been controversial in part because of the Sodium fire accident and Plutonium related radiation safety caused by transport and handling accident. Thus, many researches have been performed to ensure safety and various documents including safety requirements have been developed. In separating and reducing the long-lived radioactive transuranic(TRU) in the spent nuclear fuel, reusing as the potential energy of uranium fuel resources and reducing the high level wastes, TFFF would be receiving the attention of many people. Thus, people would wonder whether compliance with technical standards that ensures safety. For new facility design, one of the important tasks is to review of technical standards, especially for sodium and Plutonium because of water related highly reactive characteristics and criticality hazard respectively. We have introduced and reviewed two important technical standards for TFFF, which are sodium fire and plutonium criticality safety, in this paper. This paper would provide a brief guidance, about how to start and what is important, to people who are responsible for the initial design to operation of TFFF

  4. Review of Sodium and Plutonium related Technical Standards in Trans-Uranium Fuel Fabrication Facilities

    Energy Technology Data Exchange (ETDEWEB)

    Jang, Misuk; Jeon, Jong Seon; Kang, Hyun Sik; Kim, Seoung Rae [NESS, Daejeon (Korea, Republic of)

    2016-10-15

    In this paper, we would introduce and review technical standards related to sodium fire and plutonium criticality safety. This paper may be helpful to identify considerations in the development of equipment, standards, and etc., to meet the safety requirements in the design, construction and operating of TFFF, KAPF and SFR. The feasibility and conceptual designs are being examined on related facilities, for example, TRU Fuel Fabrication Facilities (TFFF), Korea Advanced Pyro-process Facility (KAPF), and Sodium Cooled Fast Reactor (SFR), in Korea. However, the safety concerns of these facilities have been controversial in part because of the Sodium fire accident and Plutonium related radiation safety caused by transport and handling accident. Thus, many researches have been performed to ensure safety and various documents including safety requirements have been developed. In separating and reducing the long-lived radioactive transuranic(TRU) in the spent nuclear fuel, reusing as the potential energy of uranium fuel resources and reducing the high level wastes, TFFF would be receiving the attention of many people. Thus, people would wonder whether compliance with technical standards that ensures safety. For new facility design, one of the important tasks is to review of technical standards, especially for sodium and Plutonium because of water related highly reactive characteristics and criticality hazard respectively. We have introduced and reviewed two important technical standards for TFFF, which are sodium fire and plutonium criticality safety, in this paper. This paper would provide a brief guidance, about how to start and what is important, to people who are responsible for the initial design to operation of TFFF.

  5. Fuel and nuclear fuel cycle

    International Nuclear Information System (INIS)

    Prunier, C.

    1998-01-01

    The nuclear fuel is studied in detail, the best choice and why in relation with the type of reactor, the properties of the fuel cans, the choice of fuel materials. An important part is granted to the fuel assembly of PWR type reactor and the performances of nuclear fuels are tackled. The different subjects for research and development are discussed and this article ends with the particular situation of mixed oxide fuels ( materials, behavior, efficiency). (N.C.)

  6. Identification of potential safety-related incidents applicable to a breeder fuel reprocessing plant

    International Nuclear Information System (INIS)

    Perkins, W.C.

    1980-01-01

    The current emphasis on safety in all phases of the nuclear fuel cycle requires that safety features be identified and included in designs of nuclear facilities at the earliest possible stage. A popular method for the early identification of these safety features is the Preliminary Hazards Analysis. An extension of this analysis is to illustrate the nature of a hazard by its effects in accident situations, that is, to identify what are called safety-related incidents. Some useful tools are described which have been used at the Savannah River Laboratory, SRL, to make Preliminary Hazards Analyses as well as safety analyses of facilities for processing spent nuclear fuels from both power and production reactors. These tools have also been used in safety studies of waste handling operations at the Savannah River Plant. The tools are the SRL Incidents Data Bank and the What If meeting. The application of this methodology to a proposed facility which has breeder fuel reprocessing capability, the Hot Experimental Facility (HEF) is illustrated

  7. Ecology versus economy: is biohydrogen the fuel of the future?; Ecologia contra Economia: ¿es el biohidrogeno el combustible del futuro?

    Energy Technology Data Exchange (ETDEWEB)

    Patino, Rodrigo [Centro de Investigacion y de Estudios Avanzados, Unidad Merida, Merida, Yucatan (Mexico)] e-mail: rtarkus@mda.cinvestav.mx

    2009-09-15

    This work presents a literature review of scientific research on different methodologies developed to produce hydrogen. Current processes to obtain commercial hydrogen are completely unsustainable in terms of the use of natural resources and environmental degradation. Different bioprocesses have been proposed in recent years as environmentally clean alternatives to produce combustible gases, but balance has not yet been obtained between production costs and performance. Therefore, a comparative analysis is performed of the different methods to obtain hydrogen, their limitations and the future prospects for each one. An in-depth reflection is also provided about challenges and recommendations for scientific and technological research aimed at proposing hydrogen (or biohydrogen) as the substitute for fossil fuels over the course of the 21st century, including not only its production but also storage and energy transformation mechanisms. [Spanish] En este trabajo se presenta una revision bibliografica acerca de las distintas metodologias desarrolladas en investigacion cientifica para producir hidrogeno. Los procesos actuales por los que se obtiene hidrogeno comercial son completamente insostenibles en cuanto a la utilizacion de recursos naturales y deterioro del medio ambiente. En los ultimos anos se han propuesto distintos bioprocesos como alternativas medioambientalmente limpias para la produccion del combustible gaseoso, pero aun no se llega a obtener un balance entre los costos y los rendimientos de produccion. Se hace entonces un analisis comparativo de los distintos metodos de obtencion de hidrogeno, de las limitantes presentes y las perspectivas futuras para cada uno de ellos. Tambien se hace una profunda reflexion acerca del reto y la orientacion que deben tener las investigaciones cientificas y tecnologicas para proponer al hidrogeno (o al biohidrogeno) como el combustible que deba sustituir a los combustibles fosiles durante el transcurso del siglo XXI

  8. Convex optimisation approach to constrained fuel optimal control of spacecraft in close relative motion

    Science.gov (United States)

    Massioni, Paolo; Massari, Mauro

    2018-05-01

    This paper describes an interesting and powerful approach to the constrained fuel-optimal control of spacecraft in close relative motion. The proposed approach is well suited for problems under linear dynamic equations, therefore perfectly fitting to the case of spacecraft flying in close relative motion. If the solution of the optimisation is approximated as a polynomial with respect to the time variable, then the problem can be approached with a technique developed in the control engineering community, known as "Sum Of Squares" (SOS), and the constraints can be reduced to bounds on the polynomials. Such a technique allows rewriting polynomial bounding problems in the form of convex optimisation problems, at the cost of a certain amount of conservatism. The principles of the techniques are explained and some application related to spacecraft flying in close relative motion are shown.

  9. Circular economy and nuclear energy

    International Nuclear Information System (INIS)

    2017-01-01

    This article first recalls what circular economy is, and its main principles (sustainable supply, eco-design, industrial and territorial ecology, economy of function rather than of possession, extension of product lifetime, recycling). It outlines its different benefits: improved resilience, inclusion of all actors of the territory, creation of local jobs, a global vision. In the next part, the nuclear industry is presented as a pioneer in this respect through various trends and developments: closure of the fuel cycle and saving of uranium and energy in the upstream part, reduction of wastes in the downstream part, exploitation of plants on a longer term, management of the production of conventional wastes, reduction of energy consumption, evolution of the doctrine in terms of management of very low level radioactive wastes

  10. Management of research reactor; dynamic characteristics analysis for reactor structures related with vibration of HANARO fuel assembly

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, Chang Kee; Shim, Joo Sup [Shinwa Technology Information, Seoul (Korea)

    2001-04-01

    The objective of this study is to deduce the dynamic correlation between the fuel assembly and the reactor structure. Dynamic characteristics analyses for reactor structure related with vibration of HANARO fuel assembly have been performed For the dynamic characteristic analysis, the in-air models of the round and hexagonal flow tubes, 18-element and 36-element fuel assemblies, and reactor structure were developed. By calculating the hydrodynamic mass and distributing it on the in-air models, the in-water models of the flow tubes, the fuel assemblies, and the reactor structure were developed. Then, modal analyses for developed in-air and in-water models have been performed. Especially, two 18-element fuel assemblies and three 36-element fuel assemblies were included in the in-water reactor models. For the verification of the modal analysis results, the natural frequencies and the mode shapes of the fuel assembly were compared with those obtained from the experiment. Finally the analysis results of the reactor structure were compared with them performed by AECL Based on the reactor model without PCS piping, the in-water reactor model including the fuel assemblies was developed, and its modal analysis was performed. The analysis results demonstrate that there are no resonance between the fuel assembly and the reactor structures. 26 refs., 419 figs., 85 tabs. (Author)

  11. Understanding the New Economy.

    Science.gov (United States)

    Morrell, Louis R.

    2001-01-01

    Asserts that while the Nasdaq bubble did burst, the new economy is real and that failure to understand the rules of the digital economy can lead to substandard investment portfolio performance. Offers guidelines for higher education institutional investors. (EV)

  12. Cost of the external MTR-fuel cycle. (Uranium , reprocessing and related services)

    International Nuclear Information System (INIS)

    Mueller, H.; Gruber, G.

    1991-01-01

    This paper points out how the RERTR program has affected NUKEM's fuel supplies for MTRs and how the prices in the External MTR Fuel Cycle have developed during this period. In addition other potential fuel sources and services on the External MTR Fuel Cycle are given. (orig.)

  13. Public perception related to a hydrogen hybrid internal combustion engine transit bus demonstration and hydrogen fuel

    International Nuclear Information System (INIS)

    Hickson, Allister; Phillips, Al; Morales, Gene

    2007-01-01

    Hydrogen has been widely considered as a potentially viable alternative to fossil fuels for use in transportation. In addition to price competitiveness with fossil fuels, a key to its adoption will be public perceptions of hydrogen technologies and hydrogen fuel. This paper examines public perceptions of riders of a hydrogen hybrid internal combustion engine bus and hydrogen as a fuel source

  14. Knowledge Based Economy Assessment

    OpenAIRE

    Madalina Cristina Tocan

    2012-01-01

    The importance of knowledge-based economy (KBE) in the XXI century is evident. In the article the reflection of knowledge on economy is analyzed. The main point is targeted to the analysis of characteristics of knowledge expression in economy and to the construction of structure of KBE expression. This allows understanding the mechanism of functioning of knowledge economy. The authors highlight the possibility to assess the penetration level of KBE which could manifest itself trough the exist...

  15. Problems in complying with regulations related to low activity materials: Nuclear fuel cycle issues

    International Nuclear Information System (INIS)

    Coates, R.

    1997-01-01

    The range of issues relating to exemption and clearance within the nuclear fuel cycle is reviewed. It is concluded that current regulatory systems and the underpinning technical criteria are potentially inflexible and over-conservative, resulting in an imbalance in the use of society's resources. Proposals are developed for establishing practical requirements which would ensure that resource allocation is commensurate with the magnitude of the risks and in broad proportion to the other risks affecting society. Such an approach would be consistent with the concept of sustainability and could support wider public acceptance of these issues. Within this approach the practical distinction between exemption and clearance is challenged. (author)

  16. An approach to quantitative assessment of relative proliferation risks from nuclear fuel cycles

    International Nuclear Information System (INIS)

    Silvennoinen, P.; Vira, J.

    1981-01-01

    Feasibility of quantitative assessments of the risk of nuclear weapons proliferation is discussed in this paper. The proliferation risk is defined as a combined utility of the different fuel cycle processes or materials for the proscribed acquisition of a nuclear weapon. Based on a set of selected weighted criteria, the process utilities are calculated employing utility functions or fuzzy expectation values. The methods are compared to each other. The scheme appears feasible in relative comparisons while certain leeway must still be retained for political judgement. (author)

  17. Satellite formation flying relative dynamics, formation design, fuel optimal maneuvers and formation maintenance

    CERN Document Server

    Wang, Danwei; Poh, Eng Kee

    2017-01-01

    This book systematically describes the concepts and principles for multi-satellite relative motion, passive and near passive formation designs, trajectory planning and control for fuel optimal formation maneuvers, and formation flying maintenance control design. As such, it provides a sound foundation for researchers and engineers in this field to develop further theories and pursue their implementations. Though satellite formation flying is widely considered to be a major advance in space technology, there are few systematic treatments of the topic in the literature. Addressing that gap, the book offers a valuable resource for academics, researchers, postgraduate students and practitioners in the field of satellite science and engineering.

  18. Experimental Measurement of Relative Permeability Functions for Fuel Cell GDL Materials

    KAUST Repository

    Hussaini, Irfan; Wang, Chao-Yang

    2009-01-01

    Gas diffusion layer in PEM fuel cells plays a pivotal role in water management. Modeling of liquid water transport through the GDL relies on knowledge of relative permeability functions in the in-plane and through-plane directions. In the present work, air and water relative permeabilities are experimentally determined as functions of saturation for typical GDL materials such as Toray-060, -090, -120 carbon paper and E-Tek carbon cloth materials in their plain, untreated forms. Saturation is measured using an ex-situ gravimetric method. Absolute and relative permeability functions in the two directions of interest are presented. Significant departure from the generally assumed cubic function of saturation is observed. ©The Electrochemical Society.

  19. Analysis of neutronic parameters related to reduction in fuel rod diameter for Angra-1 reactor fuel elements

    International Nuclear Information System (INIS)

    Faria, Eduardo F.; Sadde, Luciano M.; Sakai, Massao; Gomes, Sydney da S.

    2000-01-01

    The actual fuel element design for Angra-1 PWR satisfies in a very conservative way the design limits established for the critical heat flux as well as for the energy stored in the fuel rod. However, that is not an optimized design under neutronic considerations. The conservative ratio of the H and U atomic densities gives rise to a harder neutron spectrum which reduces its reactivity. In this report, a reduction in fuel rod diameters has been analyzed, keeping however the same rod pitch for geometrical compatibility reasons. By increasing the H/U ratio it is possible to obtain a net gain in reactivity. The optimized diameter in its turn should not jeopardize the reactor safety requirements. The actual trends of the nuclear industry is to extend the cycles and the enrichment by using advanced fuel design. It must be emphasized that this design change gives rise to economical advantages, for example, reduced costs for uranium utilization and enrichment with a net gain in reactivity. (author)

  20. Remote technology related to the handling, storage and disposal of spent fuel. Proceedings of a technical committee meeting

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    Reduced radiation exposure, greater reliability and cost savings are all potential benefits of the application of remote technologies to the handling of spent nuclear fuel. Remote equipment and technologies are used to some extent in all facilities handling fuel and high-level wastes whether they are for interim storage, processing/repacking, reprocessing or disposal. In view of the use and benefits of remote technologies, as well as recent technical and economic developments in the area, the IAEA organized the Technical Committee Meeting (TCM) on Remote Technology Related to the Handling, Storage and/or Disposal of Spent Fuel. Twenty-one papers were presented at the TCM, divided into five general areas: 1. Choice of technologies; 2. Use of remote technologies in fuel handling; 3. Use of remote technologies for fuel inspection and characterization; 4. Remote maintenance of facilities; and 5. Current and future developments. Refs, figs and tabs.

  1. Challenges in Building a Sustainable Biobased Economy

    DEFF Research Database (Denmark)

    Mussatto, Solange I.

    2017-01-01

    for the production of fuels, chemicals, energy and materials is therefore recognized as a need by numerous industries and policy makers in countries around the world. In addition, a biobased economy has the potential to generate new jobs and even new industries, creating new opportunities for entrepreneurship...

  2. Energy sustainability performance of the regional economy

    Directory of Open Access Journals (Sweden)

    N. I. Danilov

    2005-03-01

    Full Text Available The results of the study of the dynamics of energy intensity of gross regional product of the Sverdlovsk region for the period 1996 - 2003 years. and projections for the period up to 2015. The principal possibility of growth performance of the regional economy, without a significant increase in the consumption of primary fuel.

  3. Modeling of similar economies

    Directory of Open Access Journals (Sweden)

    Sergey B. Kuznetsov

    2017-06-01

    Full Text Available Objective to obtain dimensionless criteria ndash economic indices characterizing the national economy and not depending on its size. Methods mathematical modeling theory of dimensions processing statistical data. Results basing on differential equations describing the national economy with the account of economical environment resistance two dimensionless criteria are obtained which allow to compare economies regardless of their sizes. With the theory of dimensions we show that the obtained indices are not accidental. We demonstrate the implementation of the obtained dimensionless criteria for the analysis of behavior of certain countriesrsquo economies. Scientific novelty the dimensionless criteria are obtained ndash economic indices which allow to compare economies regardless of their sizes and to analyze the dynamic changes in the economies with time. nbsp Practical significance the obtained results can be used for dynamic and comparative analysis of different countriesrsquo economies regardless of their sizes.

  4. Fabrication of preliminary fuel rods for SFR

    International Nuclear Information System (INIS)

    Kim, Sun Ki; Oh, Seok Jin; Ko, Young Mo; Woo, Youn Myung; Kim, Ki Hwan

    2012-01-01

    Metal fuels was selected for fueling many of the first reactors in the US, including the Experimental Breeder Reactor-I (EBR-I) and the Experimental Breeder Reactor-II (EBR-II) in Idaho, the FERMI-I reactor, and the Dounreay Fast Reactor (DFR) in the UK. Metallic U.Pu.Zr alloys were the reference fuel for the US Integral Fast Reactor (IFR) program. Metallic fuel has advantages such as simple fabrication procedures, good neutron economy, high thermal conductivity, excellent compatibility with a Na coolant and inherent passive safety. U-Zr-Pu alloy fuels have been used for SFR (sodium-cooled fast reactor) related to the closed fuel cycle for managing minor actinides and reducing a high radioactivity levels since the 1980s. Fabrication technology of metallic fuel for SFR has been in development in Korea as a national nuclear R and D program since 2007. For the final goal of SFR fuel rod fabrication with good performance, recently, three preliminary fuel rods were fabricated. In this paper, the preliminary fuel rods were fabricated, and then the inspection for QC(quality control) of the fuel rods was performed

  5. DEVELOPING COUNTRIES. TRANSITION ECONOMIES

    Directory of Open Access Journals (Sweden)

    Dumitru FILIPEANU

    2016-05-01

    Full Text Available According to the modern theories of economic development – the take-off, backwardness, convergence and balanced growth hypothesis - the new industrialized states from Asia seem to have noticed the advantages of backwardness from which low income countries benefited, namely the possibility to take advantage of the latest technological discoveries of advanced countries, thus achieving a faster growth than the latter which operated closer to the technological border. The assimilation of appropriate technologies, however, required the efficient mobilization and allocation of resources and the improvement of human and physical capital. While the Western countries were confronted with crises generated by inflationary shocks and movements of speculative capital, the relative isolation of countries whose economy was planned by the world economy sheltered them until 1990, unemployment being practically non-existent. Asia's exceptional economic success is not only due to borrowing Western practices, but also to the fact that Asian societies maintained certain traditional features of their own culture - such as a strong work ethic - and integrated them in the modern business environment.

  6. 10 CFR Appendix F to Part 50 - Policy Relating to the Siting of Fuel Reprocessing Plants and Related Waste Management Facilities

    Science.gov (United States)

    2010-01-01

    ... and Related Waste Management Facilities F Appendix F to Part 50 Energy NUCLEAR REGULATORY COMMISSION... Relating to the Siting of Fuel Reprocessing Plants and Related Waste Management Facilities 1. Public health... facilities for the temporary storage of highlevel radioactive wastes, may be located on privately owned...

  7. Impacts of removing fuel import subsidies in Nigeria on poverty

    International Nuclear Information System (INIS)

    Siddig, Khalid; Aguiar, Angel; Grethe, Harald; Minor, Peter; Walmsley, Terrie

    2014-01-01

    The petroleum sector contributes substantially to the Nigerian economy; however, the potential benefits are diminished due to the existence of significant subsidies on imports of petroleum products. Subsidies on imported petroleum products are considered to be an important instrument for keeping fuel prices, and hence the cost of living, low. The costs of these subsidies, however, has risen dramatically in recent years due to increased volatility in world petroleum and petroleum product prices and increased illegal exportation of subsidized petroleum products into neighboring countries. Removing the subsidy on fuel is one of the most contentious socio-economic policy issues in Nigeria today. In this paper, an economy-wide framework is used to identify the impact of removing the fuel subsidy on the Nigerian economy and investigates how alternative policies might be used to meet socio-economic objectives related to fuel subsidies. The results show that while a reduction in the subsidy generally results in an increase in Nigerian GDP, it can have a detrimental impact on household income, and in particular on poor households. Accompanying the subsidy reduction with income transfers aimed at poor households or domestic production of petroleum products can alleviate the negative impacts on household income. - Highlights: • Subsidies on imported fuel compromise the contribution of crude oil in Nigeria. • Fuel subsidies benefit households, but harm the economy. • We use an economy-wide model to identify the impact of removing the fuel subsidy. • We simulate scenarios that target the poor and promote fuel's domestic production

  8. Development of 4S and related technologies (2). Long life metallic fuel

    International Nuclear Information System (INIS)

    Yacout, A.M.; Tsuboi, Y.; Ueda, N.

    2009-01-01

    This paper provides an overview of the long life metallic fuel to be used in the 4S reactor. The 4S fuel design is presented and implications of its characteristics on fuel performance are discussed. Main design characteristics include the long fuel life time of 30 years and the wider and longer fuel pins compared to EBR-II and FFTF fuel pins. The LIFE-METAL fuel performance code was used to evaluate the performance of the 4S fuel design. The code has been validated using post irradiation examination data of metallic fuel irradiated in EBR-II. The performance evaluation shows the benign nature of the design. The design enables the fuel to perform adequately during reactor operations without violating any of a conservative set of steady state design criteria. A survey evaluation of the fuel performance is also presented. This performance bounding evaluation took into account possible fuel swelling behavior and cladding temperature range that represents worst case scenarios. The evaluation showed that the fuel maintains its integrity even under those worst case conditions. (author)

  9. Hydrogen economy and nuclear energy

    International Nuclear Information System (INIS)

    Knapp, V.

    2004-01-01

    Global energy outlooks based on present trends, such as WETO study, give little optimism about fulfilling Kyoto commitments in controlling CO2 emissions and avoiding unwanted climate consequences. Whilst the problem of radioactive waste has a prominence in public, in spite of already adequate technical solutions of safe storage for future hundreds and thousands of years, there s generally much less concern with influence of fossil fuels on global climate. In addition to electricity production, process heat and transportation are approximately equal contributors to CO2 emission. Fossil fuels in transportation present also a local pollution problem in congested regions. Backed by extensive R and D, hydrogen economy is seen as the solution, however, often without much thought where from the hydrogen in required very large quantities may come. With welcome contributions from alternative sources, nuclear energy is the only source of energy capable of producing hydrogen in very large amounts, without parallel production of CO2. Future high temperature reactors could do this most efficiently. In view of the fact that nuclear weapon proliferation is not under control, extrapolation from the present level of nuclear power to the future level required by serious attempts to reduce global CO2 emission is a matter of justified concern. Finding the sites for many hundreds of new reactors would, alone, be a formidable problem in developed regions with high population density. What is generally less well understood and not validated is that the production of nuclear hydrogen allows the required large increases of nuclear power without the accompanied increase of proliferation risks. Unlike electricity, hydrogen can be economically shipped or transported by pipelines to places very far from the place of production. Thus, nuclear production of hydrogen can be located and concentrated at few remote, controllable sites, far from the population centers and consumption regions. At such

  10. Program requirements to determine and relate fuel damage and failure thresholds to anticipated conditions in pressurized water reactors

    International Nuclear Information System (INIS)

    Loyd, R.F.; Croucher, D.W.

    1980-03-01

    Anticipated transients, licensing criteria, and damage mechanisms for PWR fuel rods are reviewed. Potential mechanistic fuel rod damage limits for PWRs are discussed. An expermental program to be conducted out-of-pile and in the Engineering Test Reactor (ETR) to generate a safety data base to define mechanistic fuel damage and failure thresholds and to relate these thresholds to the thermal-hydraulic and power conditions in a PWR is proposed. The requirements for performing the tests are outlined. Analytical support requirements are defined

  11. The International conference on fast reactors and related fuel cycles: next generation nuclear systems for sustainable development. Book of abstracts

    International Nuclear Information System (INIS)

    2017-01-01

    The materials of the International Conference on Fast Reactors and Related Fuel Cycles (June 26-29, 2017, Yekaterinburg) are presented. The forum was organized by the IAEA with the assistance of Rosatom State Corporation. The theme of the conference: “The New Generation of Nuclear Systems for Sustainable Development”. About 700 specialists from more than 30 countries took part in the conference. The state and prospects for the development of the direction of fast reactors in countries dealing with this topic were discussed. A wide range of scientific issues covered the concepts of prospective reactors, reactor cores, fuel and fuel cycles, operation and decommissioning, safety, licensing, structural materials, industrial implementation [ru

  12. Product Innovations in Emerging Economies

    DEFF Research Database (Denmark)

    Xiao, Xiao; Sarker, Saonee; Rai, Sudhanshu

    2011-01-01

    , such as countries that are not considered “developed.” This study aims at examining how firms innovate in emerging economies. Specifically, we focus on the role of collaborative capacity in product innovations. Primary data collected from an ICT project in India has been used to test the relevant hypotheses......Studies on enterprise innovations have established the relationships between a number of determinants and enterprise innovativeness. However, such studies in general have been conducted in developed economies. Recent literature has called for broadening innovation-related research to other contexts...

  13. The legal situation relating to the reprocessing in other EC member countries of spent fuel from German nuclear power stations

    International Nuclear Information System (INIS)

    Haedrich, H.

    1993-01-01

    The author states that reprocessing can continue, showing by his analysis that discontinuing the reprocessing of spent fuel from Germany in installations in France or Great Britain would mean a breach of - prior-ranking - Euratom law, which offers equally efficient protection of public security and public health and safety in accordance with the internationally defined and accepted state of the art in science and technology. In addition, such a decision would mean an infringement of the basic principles of the free market economy as laid down by the Euratom treaty and by the EC treaty, as there are no facts or conditions allowing application of the exemption provision given by the EC treaty. (orig./HP) [de

  14. An examination of flame shape related to convection heat transfer in deep-fuel beds

    Science.gov (United States)

    Kara M. Yedinak; Jack D. Cohen; Jason M. Forthofer; Mark A. Finney

    2010-01-01

    Fire spread through a fuel bed produces an observable curved combustion interface. This shape has been schematically represented largely without consideration for fire spread processes. The shape and dynamics of the flame profile within the fuel bed likely reflect the mechanisms of heat transfer necessary for the pre-heating and ignition of the fuel during fire spread....

  15. Air Pollution and Dispensed Medications for Asthma, and Possible Effect Modifiers Related to Mental Health and Socio-Economy: A Longitudinal Cohort Study of Swedish Children and Adolescents.

    Science.gov (United States)

    Oudin, Anna; Bråbäck, Lennart; Oudin Åström, Daniel; Forsberg, Bertil

    2017-11-16

    It has been suggested that children that are exposed to a stressful environment at home have an increased susceptibility for air pollution-related asthma. The aim here was to investigate the association between air pollution exposure and asthma, and effect modification by mental health and by socio-economic status (as markers of a stressful environment). All individuals under 18 years of age in four Swedish counties during 2007 to 2010 (1.2 million people) were included. The outcome was defined as dispensing at least two asthma medications during follow up. We linked data on NO₂ from an empirical land use regression to data from national registers on outcome and potential confounders. Data was analyzed with logistic regression. There was an odds ratio (OR) of 1.02 (95% Confidence Interval (CI: 1.01-1.03) for asthma associated with a 10 µg·m -3 increase in NO₂. The association only seemed to be present in areas where NO₂ was higher than 15 µg·m -3 with an OR of 1.09 (95% CI: 1.07-1.12), and the association seemed stronger in children with parents with a high education, OR = 1.05 (95% CI: 1.02-1.09) and OR = 1.04 (95% CI: 1.01-1.07) in children to mothers and father with a high education, respectively. The association did not seem to depend on medication history of psychiatric disorders. There was weak evidence for the association between air pollution and asthma to be stronger in neighborhoods with higher education levels. In conclusion, air pollution was associated with dispensed asthma medications, especially in areas with comparatively higher levels of air pollution, and in children to parents with high education. We did not observe support for our hypothesis that stressors linked to socio-economy or mental health problems would increase susceptibility to the effects of air pollution on the development of asthma.

  16. Greenhouse impact due to the use of combustible fuels: life cycle viewpoint and relative radiative forcing commitment.

    Science.gov (United States)

    Kirkinen, Johanna; Palosuo, Taru; Holmgren, Kristina; Savolainen, Ilkka

    2008-09-01

    Extensive information on the greenhouse impacts of various human actions is important in developing effective climate change mitigation strategies. The greenhouse impacts of combustible fuels consist not only of combustion emissions but also of emissions from the fuel production chain and possible effects on the ecosystem carbon storages. It is important to be able to assess the combined, total effect of these different emissions and to express the results in a comprehensive way. In this study, a new concept called relative radiative forcing commitment (RRFC) is presented and applied to depict the greenhouse impact of some combustible fuels currently used in Finland. RRFC is a ratio that accounts for the energy absorbed in the Earth system due to changes in greenhouse gas concentrations (production and combustion of fuel) compared to the energy released in the combustion of fuel. RRFC can also be expressed as a function of time in order to give a dynamic cumulative picture on the caused effect. Varying time horizons can be studied separately, as is the case when studying the effects of different climate policies on varying time scales. The RRFC for coal for 100 years is about 170, which means that in 100 years 170 times more energy is absorbed in the atmosphere due to the emissions of coal combustion activity than is released in combustion itself. RRFC values of the other studied fuel production chains varied from about 30 (forest residues fuel) to 190 (peat fuel) for the 100-year study period. The length of the studied time horizon had an impact on the RRFC values and, to some extent, on the relative positions of various fuels.

  17. Investigation on preparing data collections related to new energy technology development. Fuel cells; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Nenryo denchi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With an objective to put data related to fuel cells systematically into order, related data were collected comprehensively. Reviewing large international conferences impresses dawn of commercialization in phosphoric acid fuel cells (PAFC), take-off of megawatt-class molten carbonate fuel cells (MCFC), and remarkable advancement in studies on solid oxide fuel cells (SOFC) and polymer electrolyte fuel cells (PEFC). The data collection may be compiled as follows: basic principles, features, operation principles, system configurations, utilization fields, and characteristics were summarized on fuel cell power generation systems using phosphoric acid, polymer, molten carbonate, solid oxide, and alkaline fuel cells; major installation examples in Japan and overseas countries were summarized; investigations were given on developing other fuel cells such as alkaline type and direct methanol type fuel cells; and marketability, subsidies operations in Japan, and states of policy implementation in the U.S.A. were investigated and put into order. 22 refs., 24 figs., 21 tabs.

  18. Emerging Economies Research Dialogue | IDRC - International ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    This grant will allow the Indian Council for Research on International Economic Relations to bridge the gap by organizing two research dialogues in the form of international conferences for emerging economy professionals, academics and policymakers on issues of contemporary relevance to the global economy and polity.

  19. Plutonium economy. Plutonium-Wirtschaft

    Energy Technology Data Exchange (ETDEWEB)

    Traube, K

    1984-01-01

    The author expresses his opinion on the situation, describes the energy-economic setting, indicates the alternatives: fuel reprocessing or immediate long-term storage, and investigates the prospects for economic utilization of the breeder reactors. All the facts suggest that the breeder reactor will never be able to stand economic competition with light-water reactors. However, there is no way to prove the future. It is naive to think that every doubt could and must be removed before stopping the development of breeder reactors - and thus also the reprocessing of the fuel of light-water reactors. On the basis of the current state of knowledge an unbiased cost-benefit-analysis can only lead to the recommendation to stop construction immediately. But can 'experts', who for years or even decades have called for and supported the development of breeder reactors be expected to make an unbiased analysis. Klaus Traube strikes the balance of the state Germany's nuclear economy is in: although there is no chance of definitively abandoning that energy-political cul-de-sac, no new adventures must be embarked upon. Responsible handling of currently used nuclear technology means to give up breeder technology and waive plutonium economy. It is no supreme technology with the aid of which structural unemployment or any other economic problem could be solved.

  20. The Evolution of the Coastal Economy: The Role of Working Waterfronts in the Alabama Gulf Coast

    Directory of Open Access Journals (Sweden)

    Yaoqi Zhang

    2015-04-01

    Full Text Available This article describes the evolution of the coastal economy in Alabama and examines the driving forces of the sustainable economy in a historical context. The input-output model was applied to assess the direct and secondary effects of output and employment in the coastal region. Results suggest that state industries are heavily dependent on waterfront-related activities in this area, which have fueled much of their rapid development in the past few decades. Tourism, ship building and repairing and transportation are the three dominating sources contributing to the coastal economy. There are a few general problems of working waterfronts in the coastal Alabama area, but there are also some unique problems (e.g., Hurricane Katrina, Deepwater Horizon oil spill. Policies for future sustainable development are proposed.

  1. Relations between Air-Fuel Ratio and Dynamic Performance of Small Race Cars

    OpenAIRE

    位田, 晴良; Ida, Haruyoshi; 漁, 佑一郎; Sunadori, Yuichiro; 牧田, 俊太郎; Makita, Syuntaro; 宮﨑, 真央; Miyazaki, Manaka; 磯松, 弥司; Isomatsu, Yatsuka

    2017-01-01

    'It goes without saying that engine output power characteristics greatly affect the dynamic performance of the race car. One of the methods of changing the output power of the engine is to adjust the set amount of fuel supply. This method changes the air-fuel ratio of the air fuel mixture supplied to the engine. In this study, a slalom test run of a small race car was used to examine dynamic performance with attention to the air-fuel ratio changed by adjusting the set amount of fuel supply. T...

  2. Growing a market economy

    Energy Technology Data Exchange (ETDEWEB)

    Basu, N.; Pryor, R.J.

    1997-09-01

    This report presents a microsimulation model of a transition economy. Transition is defined as the process of moving from a state-enterprise economy to a market economy. The emphasis is on growing a market economy starting from basic microprinciples. The model described in this report extends and modifies the capabilities of Aspen, a new agent-based model that is being developed at Sandia National Laboratories on a massively parallel Paragon computer. Aspen is significantly different from traditional models of the economy. Aspen`s emphasis on disequilibrium growth paths, its analysis based on evolution and emergent behavior rather than on a mechanistic view of society, and its use of learning algorithms to simulate the behavior of some agents rather than an assumption of perfect rationality make this model well-suited for analyzing economic variables of interest from transition economies. Preliminary results from several runs of the model are included.

  3. The Sharing Economy

    DEFF Research Database (Denmark)

    Avital, Michel; Carroll, John M.; Hjalmarsson, Anders

    2015-01-01

    The sharing economy is spreading rapidly worldwide in a number of industries and markets. The disruptive nature of this phenomenon has drawn mixed responses ranging from active conflict to adoption and assimilation. Yet, in spite of the growing attention to the sharing economy, we still do not know...... much about it. With the abundant enthusiasm about the benefits that the sharing economy can unleash and the weekly reminders about its dark side, further examination is required to determine the potential of the sharing economy while mitigating its undesirable side effects. The panel will join...... the ongoing debate about the sharing economy and contribute to the discourse with insights about how digital technologies are critical in shaping this turbulent ecosystem. Furthermore, we will define an agenda for future research on the sharing economy as it becomes part of the mainstream society as well...

  4. Effects of fabrication requirements on fuel performance in relation to operating conditions. The views of Electricite de France (EDF)

    International Nuclear Information System (INIS)

    Ponticq, M.; Richer, P.; Scribe, G.

    1979-01-01

    Because of the operational constraints relating to fuel behaviour, imperfect knowledge of the behaviour of a defective fuel assembly and, in the near future, the need to adapt reactor power to grid following (load following and remote control), EDF is aiming to reduce the present rate of fuel failure. While the phenomena affecting fuel behaviour have now been listed and analysed, the efforts at reducing their consequences have yet to be completed. This can be achieved, firstly, by reducing or eliminating fabrication defects, which are responsible for failure at the beginning of fuel life, through establishment of a good quality assurance organization and the search for still higher efficiency of quality control and fabrication equipment, and secondly, by developing fabrication techniques minimizing in particular cladding-pellet interactions and the stress corrosion of the cladding, which are responsible for fuel failure as from mid-life. However, the reactor operating conditions likely to apply in the near future may lead, for a given fuel configuration, to a re-evaluation of the fabrication parameters of cladding and UO 2 pellets. (author)

  5. Biofuels sources, biofuel policy, biofuel economy and global biofuel projections

    International Nuclear Information System (INIS)

    Demirbas, Ayhan

    2008-01-01

    The term biofuel is referred to liquid, gas and solid fuels predominantly produced from biomass. Biofuels include energy security reasons, environmental concerns, foreign exchange savings, and socioeconomic issues related to the rural sector. Biofuels include bioethanol, biomethanol, vegetable oils, biodiesel, biogas, bio-synthetic gas (bio-syngas), bio-oil, bio-char, Fischer-Tropsch liquids, and biohydrogen. Most traditional biofuels, such as ethanol from corn, wheat, or sugar beets, and biodiesel from oil seeds, are produced from classic agricultural food crops that require high-quality agricultural land for growth. Bioethanol is a petrol additive/substitute. Biomethanol can be produced from biomass using bio-syngas obtained from steam reforming process of biomass. Biomethanol is considerably easier to recover than the bioethanol from biomass. Ethanol forms an azeotrope with water so it is expensive to purify the ethanol during recovery. Methanol recycles easier because it does not form an azeotrope. Biodiesel is an environmentally friendly alternative liquid fuel that can be used in any diesel engine without modification. There has been renewed interest in the use of vegetable oils for making biodiesel due to its less polluting and renewable nature as against the conventional petroleum diesel fuel. Due to its environmental merits, the share of biofuel in the automotive fuel market will grow fast in the next decade. There are several reasons for biofuels to be considered as relevant technologies by both developing and industrialized countries. Biofuels include energy security reasons, environmental concerns, foreign exchange savings, and socioeconomic issues related to the rural sector. The biofuel economy will grow rapidly during the 21st century. Its economy development is based on agricultural production and most people live in the rural areas. In the most biomass-intensive scenario, modernized biomass energy contributes by 2050 about one half of total energy

  6. Investigation of metal/carbon-related materials for fuel cell applications by electronic structure calculations

    Energy Technology Data Exchange (ETDEWEB)

    Kong, Ki-jeong [Korea Research Institute of Chemical Technology, P.O.Box 107, Yuseong, Daejeon 305-600 (Korea, Republic of)]. E-mail: kong@krict.re.kr; Choi, Youngmin [Korea Research Institute of Chemical Technology, P.O.Box 107, Yuseong, Daejeon 305-600 (Korea, Republic of); Ryu, Beyong-Hwan [Korea Research Institute of Chemical Technology, P.O.Box 107, Yuseong, Daejeon 305-600 (Korea, Republic of); Lee, Jeong-O [Korea Research Institute of Chemical Technology, P.O.Box 107, Yuseong, Daejeon 305-600 (Korea, Republic of); Chang, Hyunju [Korea Research Institute of Chemical Technology, P.O.Box 107, Yuseong, Daejeon 305-600 (Korea, Republic of)

    2006-07-15

    The potential of carbon-related materials, such as carbon nanotubes (CNTs) and graphite nanofibers (GNFs), supported metal catalysts as an electrode for fuel cell application was investigated using the first-principle electronic structure calculations. The stable binding geometries and energies of metal catalysts are determined on the CNT surface and the GNF edge. The catalyst metal is more tightly bound to the GNF edge than to the CNT surface because of the existence of active dangling bonds of edge carbon atoms. The diffusion barrier of metal atoms on the surface and edge is also obtained. From our calculation results, we have found that high dispersity is achievable for GNF due to high barrier against the diffusion of metal atoms, while CNT appears less suitable. The GNF with a large edge-to-wall ratio is more suitable for the high-performance electrode than perfect crystalline graphite or CNT.

  7. Investigation of metal/carbon-related materials for fuel cell applications by electronic structure calculations

    International Nuclear Information System (INIS)

    Kong, Ki-jeong; Choi, Youngmin; Ryu, Beyong-Hwan; Lee, Jeong-O; Chang, Hyunju

    2006-01-01

    The potential of carbon-related materials, such as carbon nanotubes (CNTs) and graphite nanofibers (GNFs), supported metal catalysts as an electrode for fuel cell application was investigated using the first-principle electronic structure calculations. The stable binding geometries and energies of metal catalysts are determined on the CNT surface and the GNF edge. The catalyst metal is more tightly bound to the GNF edge than to the CNT surface because of the existence of active dangling bonds of edge carbon atoms. The diffusion barrier of metal atoms on the surface and edge is also obtained. From our calculation results, we have found that high dispersity is achievable for GNF due to high barrier against the diffusion of metal atoms, while CNT appears less suitable. The GNF with a large edge-to-wall ratio is more suitable for the high-performance electrode than perfect crystalline graphite or CNT

  8. Economy and Grace

    DEFF Research Database (Denmark)

    Pedersen, Else Marie Wiberg

    2015-01-01

    Luther develops his idea the grace of God in tandem with his idea of economy, and a society characterized by ethical and social values such as love of neighbour and caring for the poor. Hence, the reformer's search for a gracious God is developed along with his criticism of the current indulgence...... doctrine and the emerging 'oeconomia moderna'. Thus, building on a simul gratia et oeconomia, grace and economy simultaneously, Luther's reformation theology can be perceived as te intersection of an economy of grace and a horizontal social economy (works of love) in quotidian life that together constitute...

  9. Scientific issues in fuel behaviour

    International Nuclear Information System (INIS)

    1995-01-01

    The current limits on discharge burnup in today's nuclear power stations have proven the fuel to be very reliable in its performance, with a negligibly small rate of failure. However, for reasons of economy, there are moves to increase the fuel enrichment in order to extend both the cycle time and the discharge burnup. But, longer periods of irradiation cause increased microstructural changes in the fuel and cladding, implying a larger degradation of physical and mechanical properties. This degradation may well limit the plant life, hence the NSC concluded that it is of importance to develop a predictive capability of fuel behaviour at extended burnup. This can only be achieved through an improved understanding of the basic underlying phenomena of fuel behaviour. The Task Force on Scientific Issues Related to Fuel Behaviour of the NEA Nuclear Science Committee has identified the most important scientific issues on the subject and has assigned priorities. Modelling aspects are listed in Appendix A and discussed in Part II. In addition, quality assurance process for performing and evaluating new integral experiments is considered of special importance. Main activities on fuel behaviour modelling, as carried out in OECD Member countries and international organisations, are listed in Part III. The aim is to identify common interests, to establish current coverage of selected issues, and to avoid any duplication of efforts between international agencies. (author). refs., figs., tabs

  10. THEN-2: The 2nd COE-INES international workshop on 'toward hydrogen economy; what nuclear can contribute and how'. Proposal and presentations

    International Nuclear Information System (INIS)

    2006-01-01

    The workshop of the title was held on topics; nuclear hydrogen system in cooperation with other non-nuclear energy systems related with hydrogen production, storage and transportation, and synthesized fuel productions, hydrogen energy management and economy, consisted of 3 keynote lectures and 4 topical sessions by 15 presenters and a panel discussion session. (J.P.N.)

  11. The impact of peak oil on tourism in Spain: An input-output analysis of price, demand and economy-wide effects

    NARCIS (Netherlands)

    Logar, I.; van den Bergh, J.C.J.M.

    2013-01-01

    This article examines the potential effects of peak oil on Spanish tourism and indirectly on the rest of the economy. We construct several scenarios of price increases in oil, related fossil fuels and their inflationary effects. These scenarios provide the context for an input-output (I/O) analysis

  12. International Conference on Fast Reactors and Related Fuel Cycles: Safe Technologies and Sustainable Scenarios (FR13). Presentations

    International Nuclear Information System (INIS)

    2013-01-01

    The conference, which was held from 4 to 7 of March 2013 in Paris, provided a forum to exchange information on national and international programmes, and more generally new developments and experience, in the field of fast reactors and related fuel cycle technologies. A first goal was to identify and discuss strategic and technical options that have been proposed by individual countries or companies. Another goal was to promote the development of fast reactors and related fuel cycle technologies in a safe, proliferation resistant and economic way. A third goal was to identify gaps and key issues that need to be addressed in relation to the industrial deployment of fast reactors with a closed fuel cycle. A fourth goal was to engage young scientists and engineers in this field, in particular with sustainability, innovation, simulation, safety, economics and public acceptance

  13. Obesity-related health impacts of fuel excise taxation- an evidence review and cost-effectiveness study

    Directory of Open Access Journals (Sweden)

    V. Brown

    2017-05-01

    Full Text Available Abstract Background Reducing automobile dependence and improving rates of active transport may reduce the impact of obesogenic environments, thereby decreasing population prevalence of obesity and other diseases where physical inactivity is a risk factor. Increasing the relative cost of driving by an increase in fuel taxation may therefore be a promising public health intervention for obesity prevention. Methods A scoping review of the evidence for obesity or physical activity effect of changes in fuel price or taxation was undertaken. Potential health benefits of an increase in fuel excise taxation in Australia were quantified using Markov modelling to simulate obesity, injury and physical activity related health impacts of a fuel excise taxation intervention for the 2010 Australian population. Health adjusted life years (HALYs gained and healthcare cost savings from diseases averted were estimated. Incremental cost-effectiveness ratios (ICERs were reported and results were tested through sensitivity analysis. Results Limited evidence on the effect of policies such as fuel taxation on health-related behaviours currently exists. Only three studies were identified reporting associations between fuel price or taxation and obesity, whilst nine studies reported associations specifically with physical activity, walking or cycling. Estimates of the cross price elasticity of demand for public transport with respect to fuel price vary, with limited consensus within the literature on a probable range for the Australian context. Cost-effectiveness modelling of a AUD0.10 per litre increase in fuel excise taxation using a conservative estimate of cross price elasticity for public transport suggests that the intervention would be cost-effective from a limited societal perspective (237 HALYs gained, AUD2.6 M in healthcare cost savings, measured against a comparator of no additional increase in fuel excise. Under “best case” assumptions, the intervention

  14. Obesity-related health impacts of fuel excise taxation- an evidence review and cost-effectiveness study.

    Science.gov (United States)

    Brown, V; Moodie, M; Cobiac, L; Mantilla Herrera, A M; Carter, R

    2017-05-04

    Reducing automobile dependence and improving rates of active transport may reduce the impact of obesogenic environments, thereby decreasing population prevalence of obesity and other diseases where physical inactivity is a risk factor. Increasing the relative cost of driving by an increase in fuel taxation may therefore be a promising public health intervention for obesity prevention. A scoping review of the evidence for obesity or physical activity effect of changes in fuel price or taxation was undertaken. Potential health benefits of an increase in fuel excise taxation in Australia were quantified using Markov modelling to simulate obesity, injury and physical activity related health impacts of a fuel excise taxation intervention for the 2010 Australian population. Health adjusted life years (HALYs) gained and healthcare cost savings from diseases averted were estimated. Incremental cost-effectiveness ratios (ICERs) were reported and results were tested through sensitivity analysis. Limited evidence on the effect of policies such as fuel taxation on health-related behaviours currently exists. Only three studies were identified reporting associations between fuel price or taxation and obesity, whilst nine studies reported associations specifically with physical activity, walking or cycling. Estimates of the cross price elasticity of demand for public transport with respect to fuel price vary, with limited consensus within the literature on a probable range for the Australian context. Cost-effectiveness modelling of a AUD0.10 per litre increase in fuel excise taxation using a conservative estimate of cross price elasticity for public transport suggests that the intervention would be cost-effective from a limited societal perspective (237 HALYs gained, AUD2.6 M in healthcare cost savings), measured against a comparator of no additional increase in fuel excise. Under "best case" assumptions, the intervention would be more cost-effective (3181 HALYs gained, AUD34.2

  15. Spatial dynamics in the Experience Economy

    DEFF Research Database (Denmark)

    The volume consists of 14 chapters, each presenting original research contributions. The book explores the dynamics of place, location and territories related to the experience economy. Three overall perspectives permeate the contributions of the book. The first is related to innovation and innov...... and innovation processes in the experience economy. The second is related to the governance of experiential innnovation and development. The third is the role of place in creating experiential value and vice versa....

  16. Storage, handling and movement of fuel and related components at nuclear power plants

    International Nuclear Information System (INIS)

    1979-01-01

    The report describes in general terms the various operations involved in the handling of fresh fuel, irradiated fuel, and core components such as control rods, neutron sources, burnable poisons and removable instruments. It outlines the principal safety problems in these operations and provides the broad safety criteria which must be observed in the design, operation and maintenance of equipment and facilities for handling, transferring, and storing nuclear fuel and core components at nuclear power reactor sites

  17. Improvements in or relating to gripping means for handling nuclear reactor fuel assemblies

    International Nuclear Information System (INIS)

    Batjukov, V.I.; Vjugov, O.N.; Fadeev, A.I.; Shkhian, T.G.

    1980-01-01

    A gripping means for handling fuel assemblies, the heads of which are internally recessed to receive gripping jaws, forms part of a reactor refuelling machine and is telescopically accommodated within a manipulator tube of the machine. A through hole is provided to allow cooling medium to be passed through the fuel assemblies to remove afterheat when the gripping means is used to transfer assemblies from a reactor core to spent fuel storage sockets. (author)

  18. Improvements relating to the low temperature carbonisation of coal, shale, and other suitable fuels

    Energy Technology Data Exchange (ETDEWEB)

    Hackford, J E

    1930-03-10

    In the low-temperature carbonization of coal, shale, and other suitable fuel is interposed between the fuel to be carbonized and the container, conveyor, grate, or other surface or surfaces with which the fuel normally contacts during the heat treatment. A medium decomposes during the said heat treatment, to produce a dry carbon at the surface or surfaces contacted without passing through an intermediate plastic or liquid phase during decomposition.

  19. Potential safety-related incidents with possible applicability to a nuclear fuel reprocessing plant

    International Nuclear Information System (INIS)

    Perkins, W.C.; Durant, W.S.; Dexter, A.H.

    1980-12-01

    The occurrence of certain potential events in nuclear fuel reprocessing plants could lead to significant consequences involving risk to operating personnel or to the general public. This document is a compilation of such potential initiating events in nuclear fuel reprocessing plants. Possible general incidents and incidents specific to key operations in fuel reprocessing are considered, including possible causes, consequences, and safety features designed to prevent, detect, or mitigate such incidents

  20. Economy Profile of Argentina

    OpenAIRE

    World Bank Group

    2017-01-01

    Doing Business 2018 is the 15th in a series of annual reports investigating the regulations that enhance business activity and those that constrain it. This economy profile presents the Doing Business indicators for Argentina. Doing Business presents quantitative indicators on business regulation and the protection of property rights that can be compared across 190 economies; for 2018 Arge...

  1. Economy Profile of Estonia

    OpenAIRE

    World Bank Group

    2017-01-01

    Doing Business 2018 is the 15th in a series of annual reports investigating the regulations that enhance business activity and those that constrain it. This economy profile presents the Doing Business indicators for Estonia. Doing Business presents quantitative indicators on business regulation and the protection of property rights that can be compared across 190 economies; for 2018 Estonia ...

  2. Economy Profile of Australia

    OpenAIRE

    World Bank Group

    2017-01-01

    Doing Business 2018 is the 15th in a series of annual reports investigating the regulations that enhance business activity and those that constrain it. This economy profile presents the Doing Business indicators for Australia. Doing Business presents quantitative indicators on business regulation and the protection of property rights that can be compared across 190 economies; for 2018 Aust...

  3. Economy Profile of Bolivia

    OpenAIRE

    World Bank Group

    2017-01-01

    Doing Business 2018 is the 15th in a series of annual reports investigating the regulations that enhance business activity and those that constrain it. This economy profile presents the Doing Business indicators for Bolivia. Doing Business presents quantitative indicators on business regulation and the protection of property rights that can be compared across 190 economies; for 2018 Bolivia ...

  4. Free variable economy

    NARCIS (Netherlands)

    Roelofsen, F.

    2009-01-01

    Several authors have recently argued that semantic interpretation is subject to economy constraints. In particular, Fox (1999) argued that the interpretation of pronouns is subject to BINDING ECONOMY, which favors local binding over non-local binding. The present paper points out a problem for

  5. Mechanical and thermomechanical calculations related to the storage of spent nuclear-fuel assemblies in granite

    International Nuclear Information System (INIS)

    Butkovich, T.R.

    1980-05-01

    A generic test of the geologic storage of spent-fuel assemblies is being made at Nevada Test Site. The spent-fuel assemblies were emplaced at a depth of 420 m (1370 ft) below the surface in a typical granite and will be retrieved at a later time. The early time, close-in thermal history of this type of repository is being simulated with spent-fuel and electrically heated canisters in a central drift, with auxiliary heaters in two parallel side drifts. Prior to emplacement of the spent-fuel canisters, preliminary calculations were made using a pair of existing finite-element codes, ADINA and ADINAT

  6. Underdeveloping Appalachia: Toward an environmental sociology of extractive economies

    Science.gov (United States)

    Wishart, William Ryan

    This dissertation uses mixed methods to examine the role of the coal industry in the reproduction of Central Appalachia as an internal periphery within the United States and the economic, ecological, and human inequalities this entails. It also analyzes the related political economy and power structure of coal in a national context. Particularly important for analysis of the region's underdevelopment are the class relations involved in unequal ecological exchange and the establishment of successive "modes of extraction." I employ a historical comparative analysis of Appalachia to evaluate Bunker's thesis that resource dependent peripheries often become locked into a "mode of extraction" (with aspects parallel to Marxist concepts of mode of production) triggering economic and ecological path dependencies leading to underdevelopment. This historical comparative analysis establishes the background for a closer examination of the political economy of the modern US coal industry. After sketching the changes in the structure of monopoly and competition in the coal industry I employ network analysis of the directorate interlocks of the top twenty coal firms in the US within the larger energy policy-planning network to examine their connections with key institutions of the policy formation network of think tanks and business groups. My findings show the importance of the capacities of fossil fuel fractions of the capitalist class in formulating energy policy around issues such as the 2009 climate legislation. As a contribution to the growing literature applying the concept of metabolism as link between contemporary and classical theory, I examine the conflict at Coal River Mountain from the vantage points of ecology, political economy, and human development in dialectical rotation. Utilizing Marx's method of successive abstractions, the mountain is presented as a nexus of metabolic rifts in the human relationship to the earth's natural systems and an impediment to genuine

  7. Ways of reducing radiation exposure in a future nuclear power economy

    International Nuclear Information System (INIS)

    Morgan, K.Z.

    1976-01-01

    The reasons for attempting to reduce radiation exposure in a future nuclear power economy are first discussed. This is followed by a detailed examination of ways for reducing exposures. The entire fuel cycle from uranium mining through fuel reprocessing is covered but special attention is devoted to reactors, fuel and waste shipping and fuel reprocessing

  8. Advancements in the behavioral modeling of fuel elements and related structures

    International Nuclear Information System (INIS)

    Billone, M.C.; Montgomery, R.O.; Rashid, Y.R.; Head, J.L.

    1989-01-01

    An important aspect of the design and analysis of nuclear reactors is the ability to predict the behavior of fuel elements in the adverse environment of a reactor system. By understanding the thermomechanical behavior of the different materials which constitute a nuclear fuel element, analysis and predictions can be made regarding the integrity and reliability of fuel element designs. The SMiRT conference series, through the division on fuel elements and the post-conference seminars on fuel element modeling, provided technical forums for the international participation in the exchange of knowledge concerning the thermomechanical modeling of fuel elements. This paper discusses the technical advances in the behavioral modeling of fuel elements presented at the SMiRT conference series since its inception in 1971. Progress in the areas of material properties and constitutive relationships, modeling methodologies, and integral modeling approaches was reviewed and is summarized in light of their impact on the thermomechanical modeling of nuclear fuel elements. 34 refs., 5 tabs

  9. Alcohol fuels for developing countries

    International Nuclear Information System (INIS)

    Bhattacharya, Partha

    1993-01-01

    The importance of alcohol as an alternative fuel has been slowly established. In countries such as Brazil, they are already used in transport and other sectors of economy. Other developing countries are also trying out experiments with alcohol fuels. Chances of improving the economy of many developing nations depends to a large extent on the application of this fuel. The potential for alcohol fuels in developing countries should be considered as part of a general biomass-use strategy. The final strategies for the development of alcohol fuel will necessarily reflect the needs, values, and conditions of the individual nations, regions, and societies that develop them. (author). 5 refs

  10. New technology and fuel cycles

    International Nuclear Information System (INIS)

    Mooradian, A.J.

    1979-06-01

    The means of improving uranium utilization in nuclear power reactors are reviewed with respect to economic considerations, assurance of adequate fuel supplies and risk of weapons proliferation. Reference is made to what can be done to improve fuel economy in existing reactor systems operating on a once-through fuel cycle and the potential for improvement offered by fuel recycle in those systems. The state of development of new reactor systems that offer significant savings in uranium utilization is also reviewed and conclusions are made respecting the policy implications of the search for fuel economy. (author)

  11. The solar-hydrogen economy: an analysis

    Science.gov (United States)

    Reynolds, Warren D.

    2007-09-01

    The 20th Century was the age of the Petroleum Economy while the 21st Century is certainly the age of the Solar-Hydrogen Economy. The global Solar-Hydrogen Economy that is now emerging follows a different logic. Under this new economic paradigm, new machines and methods are once again being developed while companies are restructuring. The Petroleum Economy will be briefly explored in relation to oil consumption, Hubbert's curve, and oil reserves with emphasis on the "oil crash". Concerns and criticisms about the Hydrogen Economy will be addressed by debunking some of the "hydrogen myths". There are three major driving factors for the establishment of the Solar-Hydrogen Economy, i.e. the environment, the economy with the coming "oil crash", and national security. The New Energy decentralization pathway has developed many progressive features, e.g., reducing the dependence on oil, reducing the air pollution and CO II. The technical and economic aspects of the various Solar-Hydrogen energy options and combinations will be analyzed. A proposed 24-hour/day 200 MWe solar-hydrogen power plant for the U.S. with selected energy options will be discussed. There are fast emerging Solar Hydrogen energy infrastructures in the U.S., Europe, Japan and China. Some of the major infrastructure projects in the transportation and energy sectors will be discussed. The current and projected growth in the Solar-Hydrogen Economy through 2045 will be given.

  12. Fossil Fuels.

    Science.gov (United States)

    Crank, Ron

    This instructional unit is one of 10 developed by students on various energy-related areas that deals specifically with fossil fuels. Some topics covered are historic facts, development of fuels, history of oil production, current and future trends of the oil industry, refining fossil fuels, and environmental problems. Material in each unit may…

  13. A hydrogen economy: opportunities and challenges

    International Nuclear Information System (INIS)

    Tseng, P.; Lee, J.; Friley, P.

    2005-01-01

    A hydrogen economy, the long-term goal of many nations, can potentially confer energy security, along with environmental and economic benefits. However, the transition from a conventional petroleum-based energy system to a hydrogen economy involves many uncertainties, such as the development of efficient fuel-cell technologies, problems in hydrogen production and its distribution infrastructure, and the response of petroleum markets. This study uses the US MARKAL model to simulate the impacts of hydrogen technologies on the US energy system and to identify potential impediments to a successful transition. Preliminary findings highlight possible market barriers facing the hydrogen economy, as well as opportunities in new R and D and product markets for bioproducts. Quantitative analysis also offers insights on policy options for promoting hydrogen technologies. (author)

  14. RECIPROCITY IN THE ECONOMY OF THE AGE OF SILICON ECONOMY SYSTEMS TO EARLY EXPERIENCES CURRENT SOLIDARITY ECONOMY

    Directory of Open Access Journals (Sweden)

    Horacio, Simes

    2012-01-01

    Full Text Available Reciprocity is an integrating principle of supportive economy activities. In non-capitalist societies, it has been realized through the participation of certain institutional arrangements that favored the stability of exchange relations. Progress towards capitalist societies and deepening them, dissolved many of these institutional supports, while economy relations separated from other social relations in which it was first inserted. In addition, the selfish individual was become an active participant in the economy life of society. With the construction of market economies and state regulation, reciprocal relationships were being reduced to a lower field activities. Under these circumstances, they should investigate how reciprocity is manifested today, the institutional arrangements that are suitable to give stability and unity to cooperative behavior and the dynamics of their relationship to the context of the market and the state.

  15. Direct hydrogen fuel cell systems for hybrid vehicles

    Science.gov (United States)

    Ahluwalia, Rajesh K.; Wang, X.

    Hybridizing a fuel cell system with an energy storage system offers an opportunity to improve the fuel economy of the vehicle through regenerative braking and possibly to increase the specific power and decrease the cost of the combined energy conversion and storage systems. Even in a hybrid configuration it is advantageous to operate the fuel cell system in a load-following mode and use the power from the energy storage system when the fuel cell alone cannot meet the power demand. This paper discusses an approach for designing load-following fuel cell systems for hybrid vehicles and illustrates it by applying it to pressurized, direct hydrogen, polymer-electrolyte fuel cell (PEFC) systems for a mid-size family sedan. The vehicle level requirements relative to traction power, response time, start-up time and energy conversion efficiency are used to select the important parameters for the PEFC stack, air management system, heat rejection system and the water management system.

  16. Concerning major items in government ordinance requiring modification of part of enforcement regulation for law relating to control of nuclear material, nuclear fuel and nuclear reactor

    International Nuclear Information System (INIS)

    1989-01-01

    The report describes major items planned to be incorporated into the enforcement regulations for laws relating to control of nuclear material, nuclear fuel and nuclear reactor. The modifications have become necessary for the nation to conclude a nuclear material protection treaty with other countries. The modification include the definitions of 'special nuclear fuel substances' and 'special nuclear fuel substances' and 'special nuclear fuel substances subject to protection'. The modifications require that protective measures be taken when handling and transporting special nuclear fuel substances subject to protection. Transport of special nuclear fuel substances requires approval from the Prime Minister or Transport Minister. Transport of special nuclear fuel substances subject to protection should be conducted after notifying the prefectural Public Safety Commission. Transport of special nuclear fuel substances subject to protection requires the conclusion of arrangements among responsible persons and approval of them from the Prime Minister. (N.K.)

  17. The Political Economy of Extraterritoriality

    Directory of Open Access Journals (Sweden)

    Paul B. Stephan

    2013-06-01

    Full Text Available Near the end of the 2009 Term the Supreme Court decided Morrison v. Australia National Bank, Ltd., the strongest anti-extraterritoriality opinion it has produced in modern times. Not only is Congress presumed generally to prefer only territorial regulation, but lower courts that had carved out exceptions from this principle over a long period of time must now revisit their positions. Again this year in Kiobel v. Royal Dutch Shell Co. the Court relied on an aggressive use of the presumption against extraterritoriality to cut back on an important field of private litigation. The Court appears to have embraced two related stances: The imposition of barriers to extraterritorial regulation generally advances welfare, and the lower courts cannot be trusted to determine those instances where an exception to this rule might be justified. Implicit in the Court's position are intuitions about the political economy of both legislation and litigation. I want to use the occasion of the Morrison and Kiobel decisions to consider the political economy of extraterritorial regulation by the United States. International lawyers for the most part have analyzed state decisions to exercise prescriptive jurisdiction over extraterritorial transactions in terms of a welfare calculus that determines the likely costs and benefits to the state as a whole. Fewer studies have considered the political economy of the decision whether to regulate foreign transactions. No work of which I am aware has considered the political economy of deciding the extraterritorial question through litigation. This paper seeks to fill these gaps by sketching out what political economy suggests both about extraterritoriality and the role of courts as arbiters of extraterritoriality.

  18. Issues relating to spent nuclear fuel storage on the Oak Ridge Reservation

    International Nuclear Information System (INIS)

    Klein, J.A.; Turner, D.W.

    1994-01-01

    Currently, about 2,800 metric tons of spent nuclear fuel (SNF) is stored in the US, 1,000 kg of SNF (or about 0.03% of the nation's total) are stored at the US Department of Energy (DOE) complex in Oak Ridge, Tennessee. However small the total quantity of material stored at Oak Ridge, some of the material is quite singular in character and, thus, poses unique management concerns. The various types of SNF stored at Oak Ridge will be discussed including: (1) High-Flux Isotope Reactor (HFIR) and future Advanced Neutron Source (ANS) fuels; (2) Material Testing Reactor (MTR) fuels, including Bulk Shielding Reactor (BSR) and Oak Ridge Research Reactor (ORR) fuels; (3) Molten Salt Reactor Experiment (MSRE) fuel; (4) Homogeneous Reactor Experiment (HRE) fuel; (5) Miscellaneous SNF stored in Oak Ridge National Laboratory's (ORNL's) Solid Waste Storage Areas (SWSAs); (6) SNF stored in the Y-12 Plant 9720-5 Warehouse including Health. Physics Reactor (HPRR), Space Nuclear Auxiliary Power (SNAP-) 10A, and DOE Demonstration Reactor fuels

  19. Accidents and failures related to nuclear fuel facilities and nuclear power stations in fiscal 1982

    International Nuclear Information System (INIS)

    1983-01-01

    In the chemical preparation room of the reprocessing plant in the Tokai Establishment, Power Reactor and Nuclear Fuel Development Corp., the nasal contamination of small amount (3.6 pCi at maximum) was detected on two workers in June, 1982, but abnormality was not observed in the Lung-monitor of the workers themselves. There was not the effect to the surrounding environment. The failures reported by electric power companies to the Agency of Natural Resources and Energy in accordance with the laws related to atomic energy were 26 cases. The main causes were 5 cases due to improper design management, 2 cases due to improper manufacture management, 4 cases due to improper construction management, 11 cases due to improper maintenance management and 4 other cases. Among those 26 cases, 17 cases occurred in operation, and 9 cases occurred or were detected during shutdown such as regular inspection. Among the 17 cases, 7 cases were the automatic stop by reactor protection system, and 10 cases were the finding by regular in-operation inspection. Among the 9 cases, 5 cases were the breaking of steam generator tubes, 2 cases the breaking of bumper plates at feed heater entrance, and 2 cases other troubles. Moreover, there were 41 minor troubles. (Kako, I.)

  20. Quality and environmental aspects in relation to the application of pulverized fuel ash

    International Nuclear Information System (INIS)

    Berg, J.W. van den

    1991-01-01

    In the Netherlands pulverised coal from different parts of the world is used in 5 coalfired power stations which each have 1 to 3 boilers, which in turn are equipped with various types of burners. This causes a large variation in the composition of the pulverized fuel ash (PFA). The PFA is marketed in several areas, each of which has its own specific quality requirements. These requirements are partially dictated in standard specifications. In order to obtain insight into the quality of the PFA, samples are taken and analysed daily. Rules for certification, concerning the quality and the quality control of PFA for use in concrete in The Netherlands have been agreed upon. The environmental aspects in relation to the application of PFA concern the working conditions and health aspects during processing and the environmental impact when PFA is used as a building material. The Dutch legislation concerning the environmental consequences of the application of PFA and other secondary materials is currently under review. 3 tabs