A study on the thermal expansion characteristics of simulated spent fuel and simulated DUPIC fuel

International Nuclear Information System (INIS)

Kang, Kweon Ho; Ryu, H. J.; Kim, H. S.; Song, K. C.; Yang, M. S.

2001-10-01

Thermal expansions of simulated spent PWR fuel and simulated DUPIC fuel were studied using a dilatometer in the temperature range from 298 to 1900 K. The densities of simulated spent PWR fuel and simulated DUPIC fuel used in the measurement were 10.28 g/cm3 (95.35 % of TD) and 10.26 g/cm3 (95.14 % of TD), respectively. Their linear thermal expansions of simulated fuels are higher than that of UO2, and the difference between these fuels and UO2 increases progressively as temperature increases. However, the difference between simulated spent PWR fuel and simulated DUPIC fuel can hardly be observed. For the temperature range from 298 to 1900 K, the values of the average linear thermal expansion coefficients for simulated spent PWR fuel and simulated DUPIC fuel are 1.391 10-5 and 1.393 10-5 K-1, respectively. As temperature increases to 1900 K, the relative densities of simulated spent PWR fuel and simulated DUPIC fuel decrease to 93.81 and 93.76 % of initial densities at 298 K, respectively

The relation between cognitive and metacognitive strategic processing during a science simulation.

Science.gov (United States)

Dinsmore, Daniel L; Zoellner, Brian P

2018-03-01

This investigation was designed to uncover the relations between students' cognitive and metacognitive strategies used during a complex climate simulation. While cognitive strategy use during science inquiry has been studied, the factors related to this strategy use, such as concurrent metacognition, prior knowledge, and prior interest, have not been investigated in a multidimensional fashion. This study addressed current issues in strategy research by examining not only how metacognitive, surface-level, and deep-level strategies influence performance, but also how these strategies related to each other during a contextually relevant science simulation. The sample for this study consisted of 70 undergraduates from a mid-sized Southeastern university in the United States. These participants were recruited from both physical and life science (e.g., biology) and education majors to obtain a sample with variance in terms of their prior knowledge, interest, and strategy use. Participants completed measures of prior knowledge and interest about global climate change. Then, they were asked to engage in an online climate simulator for up to 30 min while thinking aloud. Finally, participants were asked to answer three outcome questions about global climate change. Results indicated a poor fit for the statistical model of the frequency and level of processing predicting performance. However, a statistical model that independently examined the influence of metacognitive monitoring and control of cognitive strategies showed a very strong relation between the metacognitive and cognitive strategies. Finally, smallest space analysis results provided evidence that strategy use may be better captured in a multidimensional fashion, particularly with attention paid towards the combination of strategies employed. Conclusions drawn from the evidence point to the need for more dynamic, multidimensional models of strategic processing that account for the patterns of optimal and non

Simulator: A Pilot Interactive Simulation Program for Use in Teaching Public Relations.

Science.gov (United States)

Pavlik, John V.

An interactive simulation program was developed for use in teaching students how to handle public relations problems. The program user is placed in the role of assistant newsletter editor, facing a series of decision-making situations. Each choice the user makes affects the subsequent reality created by the program, which is designed to provide…

Dropout during a driving simulator study: A survival analysis.

Science.gov (United States)

Matas, Nicole A; Nettelbeck, Ted; Burns, Nicholas R

2015-12-01

Simulator sickness is the occurrence of motion-sickness like symptoms that can occur during use of simulators and virtual reality technologies. This study investigated individual factors that contributed to simulator sickness and dropout while using a desktop driving simulator. Eighty-eight older adult drivers (mean age 72.82±5.42years) attempted a practice drive and two test drives. Participants also completed a battery of cognitive and visual assessments, provided information on their health and driving habits, and reported their experience of simulator sickness symptoms throughout the study. Fifty-two participants dropped out before completing the driving tasks. A time-dependent Cox Proportional Hazards model showed that female gender (HR=2.02), prior motion sickness history (HR=2.22), and Mini-SSQ score (HR=1.55) were associated with dropout. There were no differences between dropouts and completers on any of the cognitive abilities tests. Older adults are a high-risk group for simulator sickness. Within this group, female gender and prior motion sickness history are related to simulator dropout. Higher reported experience of symptoms of simulator sickness increased rates of dropout. The results highlight the importance of screening and monitoring of participants in driving simulation studies. Older adults, females, and those with a prior history of motion sickness may be especially at risk. Copyright © 2015 Elsevier Ltd and National Safety Council. All rights reserved.

Some issues in the simulation of two-phase flows: The relative velocity

International Nuclear Information System (INIS)

Gräbel, J.; Hensel, S.; Ueberholz, P.; Farber, P.; Zeidan, D.

2016-01-01

In this paper we compare numerical approximations for solving the Riemann problem for a hyperbolic two-phase flow model in two-dimensional space. The model is based on mixture parameters of state where the relative velocity between the two-phase systems is taken into account. This relative velocity appears as a main discontinuous flow variable through the complete wave structure and cannot be recovered correctly by some numerical techniques when simulating the associated Riemann problem. Simulations are validated by comparing the results of the numerical calculation qualitatively with OpenFOAM software. Simulations also indicate that OpenFOAM is unable to resolve the relative velocity associated with the Riemann problem.

Some issues in the simulation of two-phase flows: The relative velocity

Energy Technology Data Exchange (ETDEWEB)

Gräbel, J.; Hensel, S.; Ueberholz, P.; Farber, P. [Niederrhein University of Applied Sciences, Institute for Modelling and High Performance Computing, Reinarzstraße 49, 47805 Krefeld (Germany); Zeidan, D. [School of Basic Sciences and Humanities, German Jordanian University, Amman (Jordan)

2016-06-08

In this paper we compare numerical approximations for solving the Riemann problem for a hyperbolic two-phase flow model in two-dimensional space. The model is based on mixture parameters of state where the relative velocity between the two-phase systems is taken into account. This relative velocity appears as a main discontinuous flow variable through the complete wave structure and cannot be recovered correctly by some numerical techniques when simulating the associated Riemann problem. Simulations are validated by comparing the results of the numerical calculation qualitatively with OpenFOAM software. Simulations also indicate that OpenFOAM is unable to resolve the relative velocity associated with the Riemann problem.

How Do Simulated Error Experiences Impact Attitudes Related to Error Prevention?

Science.gov (United States)

Breitkreuz, Karen R; Dougal, Renae L; Wright, Melanie C

2016-10-01

The objective of this project was to determine whether simulated exposure to error situations changes attitudes in a way that may have a positive impact on error prevention behaviors. Using a stratified quasi-randomized experiment design, we compared risk perception attitudes of a control group of nursing students who received standard error education (reviewed medication error content and watched movies about error experiences) to an experimental group of students who reviewed medication error content and participated in simulated error experiences. Dependent measures included perceived memorability of the educational experience, perceived frequency of errors, and perceived caution with respect to preventing errors. Experienced nursing students perceived the simulated error experiences to be more memorable than movies. Less experienced students perceived both simulated error experiences and movies to be highly memorable. After the intervention, compared with movie participants, simulation participants believed errors occurred more frequently. Both types of education increased the participants' intentions to be more cautious and reported caution remained higher than baseline for medication errors 6 months after the intervention. This study provides limited evidence of an advantage of simulation over watching movies describing actual errors with respect to manipulating attitudes related to error prevention. Both interventions resulted in long-term impacts on perceived caution in medication administration. Simulated error experiences made participants more aware of how easily errors can occur, and the movie education made participants more aware of the devastating consequences of errors.

COMPREHENSIVE GYROKINETIC SIMULATION OF TOKAMAK TURBULENCE AT FINITE RELATIVE GYRORADIUS

International Nuclear Information System (INIS)

WALTZ, R.E.; CANDY, J.; ROSENBLUTH, M.N.

2002-01-01

OAK B202 COMPREHENSIVE GYROKINETIC SIMULATION OF TOKAMAK TURBULENCE AT FINITE RELATIVE GYRORADIUS. A continuum global gyrokinetic code GYRO has been developed to comprehensively simulate turbulent transport in actual experimental profiles and allow direct quantitative comparisons to the experimental transport flows. GYRO not only treats the now standard ion temperature gradient (ITG) mode turbulence, but also treats trapped and passing electrons with collisions and finite beta, and all in real tokamak geometry. Most importantly the code operates at finite relative gyroradius (ρ*) so as to treat the profile shear stabilization effects which break gyroBohm scaling. The code operates in a cyclic flux tube limit which allows only gyroBohm scaling and a noncyclic radial annulus with physical profile variation. The later requires an adaptive source to maintain equilibrium profiles. Simple ITG simulations demonstrate the broken gyroBohm scaling depends on the actual rotational velocity shear rates competing with mode growth rates, direct comprehensive simulations of the DIII-D ρ*-scaled L-mode experiments are presented as a quantitative test of gyrokinetics and the paradigm

Event-by-event simulation of single-neutron experiments to test uncertainty relations

International Nuclear Information System (INIS)

Raedt, H De; Michielsen, K

2014-01-01

Results from a discrete-event simulation of a recent single-neutron experiment that tests Ozawa's generalization of Heisenberg's uncertainty relation are presented. The event-based simulation algorithm reproduces the results of the quantum theoretical description of the experiment but does not require the knowledge of the solution of a wave equation, nor does it rely on detailed concepts of quantum theory. In particular, the data from these non-quantum simulations satisfy uncertainty relations derived in the context of quantum theory. (paper)

Cosmological hydrodynamical simulations of galaxy clusters: X-ray scaling relations and their evolution

Science.gov (United States)

Truong, N.; Rasia, E.; Mazzotta, P.; Planelles, S.; Biffi, V.; Fabjan, D.; Beck, A. M.; Borgani, S.; Dolag, K.; Gaspari, M.; Granato, G. L.; Murante, G.; Ragone-Figueroa, C.; Steinborn, L. K.

2018-03-01

We analyse cosmological hydrodynamical simulations of galaxy clusters to study the X-ray scaling relations between total masses and observable quantities such as X-ray luminosity, gas mass, X-ray temperature, and YX. Three sets of simulations are performed with an improved version of the smoothed particle hydrodynamics GADGET-3 code. These consider the following: non-radiative gas, star formation and stellar feedback, and the addition of feedback by active galactic nuclei (AGN). We select clusters with M500 > 1014 M⊙E(z)-1, mimicking the typical selection of Sunyaev-Zeldovich samples. This permits to have a mass range large enough to enable robust fitting of the relations even at z ˜ 2. The results of the analysis show a general agreement with observations. The values of the slope of the mass-gas mass and mass-temperature relations at z = 2 are 10 per cent lower with respect to z = 0 due to the applied mass selection, in the former case, and to the effect of early merger in the latter. We investigate the impact of the slope variation on the study of the evolution of the normalization. We conclude that cosmological studies through scaling relations should be limited to the redshift range z = 0-1, where we find that the slope, the scatter, and the covariance matrix of the relations are stable. The scaling between mass and YX is confirmed to be the most robust relation, being almost independent of the gas physics. At higher redshifts, the scaling relations are sensitive to the inclusion of AGNs which influences low-mass systems. The detailed study of these objects will be crucial to evaluate the AGN effect on the ICM.

Simulation of growing grains under orientation relation - dependent quadruple point dragging

International Nuclear Information System (INIS)

Ito, K

2015-01-01

The growth behaviour of a specified grain embedded in matrix grains, for which the migration mobility of the quadruple points depended on the relation between the orientations of the growing and shrinking grains, was studied using a modified Potts MC-type threedimensional simulation. Large embedded grains continued to grow without being overcome by coarsening matrix grains, whereas small embedded grains disappeared, under the influence of the relative mobilities of the quadruple points, the composition of the matrix grain texture and the width of the grain size distribution of the matrix grains. These results indicate that orientation relation-dependent quadruple point dragging can affect the recrystallization texture during the grain coarsening stage. (paper)

Dual-energy mammography: simulation studies

International Nuclear Information System (INIS)

Bliznakova, K; Kolitsi, Z; Pallikarakis, N

2006-01-01

This paper presents a mammography simulator and demonstrates its applicability in feasibility studies in dual-energy (DE) subtraction mammography. This mammography simulator is an evolution of a previously presented x-ray imaging simulation system, which has been extended with new functionalities that are specific for DE simulations. The new features include incident exposure and dose calculations, the implementation of a DE subtraction algorithm as well as amendments to the detector and source modelling. The system was then verified by simulating experiments and comparing their results against published data. The simulator was used to carry out a feasibility study of the applicability of DE techniques in mammography, and more precisely to examine whether this modality could result in better visualization and detection of microcalcifications. Investigations were carried out using a 3D breast software phantom of average thickness, monoenergetic and polyenergetic beam spectra and various detector configurations. Dual-shot techniques were simulated. Results showed the advantage of using monoenergetic in comparison with polyenergetic beams. Optimization studies with monochromatic sources were carried out to obtain the optimal low and high incident energies, based on the assessment of the figure of merit of the simulated microcalcifications in the subtracted images. The results of the simulation study with the optimal energies demonstrated that the use of the DE technique can improve visualization and increase detectability, allowing identification of microcalcifications of sizes as small as 200 μm. The quantitative results are also verified by means of a visual inspection of the synthetic images

Solvent effect on Rb+ to K+ ion mutation: Monte Carlo simulation study

International Nuclear Information System (INIS)

Kim, Hag Sung

2000-01-01

The solvent effects on the relative free energies of solvation and the difference in partition coefficients (log P) for Rb + to K + mutation in several solvents have been investigated using Monte Carlo simulation (MCS) of statistical perturbation theory (SPT). In comparing the relative free energies for interconversion of one ion pair, Rb + to K + , in H 2 O (TIP4P) in this study with the relative free energies of the computer simulations and the experimental, we found that the figure in this study is -5.00 ± 0.11 kcal/mol. There is good agreement among various studies, taking into account both methods used to obtain the hydration free energies and standard deviations. There is also good agreement between the calculated structural properties of this study and the simulations, ab initio and the experimental results. We have explained the deviation of the relationship between the free energy difference and the Onsager dielectric function of solvents by the electron pair donor properties of the solvents. For the Rb + and K + ion pair, the Onsager dielectric function of solvents (or solvent permittivity), donor number of solvent and the differences in solvation dominate the differences in the relative free energies of solvation and partition coefficients

Biological consequences of environmental changes related to coastal upwelling: a simulation study

Energy Technology Data Exchange (ETDEWEB)

Howe, S.O.

1979-05-01

Two simulation models of marine ecosystem dynamics are formulated and applied to field data. The first is a time-dependent model of phytoplankton growth in nutrient-enriched batch cultures where spatial gradients of dependent variables and the effects of higher tropic level processes are not included. Rates of photosynthesis, nutrient uptake, chlorophyll synthesis and cell division for a single phytoplankton functional group are simulated as functions of photosynthetically active solar radiation, dissolved nutrient concentrations and cell quotas of carbon, nitrogen and silica. The second model combines the phytoplankton growth model with a time dependent, two-dimensional model of coastal upwelling off northwest Africa.

Relative solvation free energies calculated using an ab initio QM/MM-based free energy perturbation method: dependence of results on simulation length.

Science.gov (United States)

Reddy, M Rami; Erion, Mark D

2009-12-01

Molecular dynamics (MD) simulations in conjunction with thermodynamic perturbation approach was used to calculate relative solvation free energies of five pairs of small molecules, namely; (1) methanol to ethane, (2) acetone to acetamide, (3) phenol to benzene, (4) 1,1,1 trichloroethane to ethane, and (5) phenylalanine to isoleucine. Two studies were performed to evaluate the dependence of the convergence of these calculations on MD simulation length and starting configuration. In the first study, each transformation started from the same well-equilibrated configuration and the simulation length was varied from 230 to 2,540 ps. The results indicated that for transformations involving small structural changes, a simulation length of 860 ps is sufficient to obtain satisfactory convergence. In contrast, transformations involving relatively large structural changes, such as phenylalanine to isoleucine, require a significantly longer simulation length (>2,540 ps) to obtain satisfactory convergence. In the second study, the transformation was completed starting from three different configurations and using in each case 860 ps of MD simulation. The results from this study suggest that performing one long simulation may be better than averaging results from three different simulations using a shorter simulation length and three different starting configurations.

Cost savings from reduced catheter-related bloodstream infection after simulation-based education for residents in a medical intensive care unit.

Science.gov (United States)

Cohen, Elaine R; Feinglass, Joe; Barsuk, Jeffrey H; Barnard, Cynthia; O'Donnell, Anna; McGaghie, William C; Wayne, Diane B

2010-04-01

Interventions to reduce preventable complications such as catheter-related bloodstream infections (CRBSI) can also decrease hospital costs. However, little is known about the cost-effectiveness of simulation-based education. The aim of this study was to estimate hospital cost savings related to a reduction in CRBSI after simulation training for residents. This was an intervention evaluation study estimating cost savings related to a simulation-based intervention in central venous catheter (CVC) insertion in the Medical Intensive Care Unit (MICU) at an urban teaching hospital. After residents completed a simulation-based mastery learning program in CVC insertion, CRBSI rates declined sharply. Case-control and regression analysis methods were used to estimate savings by comparing CRBSI rates in the year before and after the intervention. Annual savings from reduced CRBSIs were compared with the annual cost of simulation training. Approximately 9.95 CRBSIs were prevented among MICU patients with CVCs in the year after the intervention. Incremental costs attributed to each CRBSI were approximately $82,000 in 2008 dollars and 14 additional hospital days (including 12 MICU days). The annual cost of the simulation-based education was approximately $112,000. Net annual savings were thus greater than $700,000, a 7 to 1 rate of return on the simulation training intervention. A simulation-based educational intervention in CVC insertion was highly cost-effective. These results suggest that investment in simulation training can produce significant medical care cost savings.

Study of physical properties, gas generation and gas retention in simulated Hanford waste

International Nuclear Information System (INIS)

Bryan, S.A.; Pederson, L.R.; Scheele, R.D.

1993-04-01

The purpose of this study was to establish the chemical and physical processes responsible for the generation and retention of gases within high-level waste from Tank 101-SY on the Hanford Site. This research, conducted using simulated waste on a laboratory scale, supports the development of mitigation/remediation strategies for Tank 101-SY. Simulated waste formulations are based on actual waste compositions. Selected physical properties of the simulated waste are compared to properties of actual Tank 101-SY waste samples. Laboratory studies using aged simulated waste show that significant gas generation occurs thermally at current tank temperatures (∼60 degrees C). Gas compositions include the same gases produced in actual tank waste, primarily N 2 , N 2 O, and H 2 . Gas stoichiometries have been shown to be greatly influenced by several organic and inorganic constituents within the simulated waste. Retention of gases in the simulated waste is in the form of bubble attachment to solid particles. This attachment phenomenon is related to the presence of organic constituents (HEDTA, EDTA, and citrate) of the simulated waste. A mechanism is discussed that relates the gas bubble/particle interactions to the partially hydrophobic surface produced on the solids by the organic constituents

Conducting Simulation Studies in the R Programming Environment.

Science.gov (United States)

Hallgren, Kevin A

2013-10-12

Simulation studies allow researchers to answer specific questions about data analysis, statistical power, and best-practices for obtaining accurate results in empirical research. Despite the benefits that simulation research can provide, many researchers are unfamiliar with available tools for conducting their own simulation studies. The use of simulation studies need not be restricted to researchers with advanced skills in statistics and computer programming, and such methods can be implemented by researchers with a variety of abilities and interests. The present paper provides an introduction to methods used for running simulation studies using the R statistical programming environment and is written for individuals with minimal experience running simulation studies or using R. The paper describes the rationale and benefits of using simulations and introduces R functions relevant for many simulation studies. Three examples illustrate different applications for simulation studies, including (a) the use of simulations to answer a novel question about statistical analysis, (b) the use of simulations to estimate statistical power, and (c) the use of simulations to obtain confidence intervals of parameter estimates through bootstrapping. Results and fully annotated syntax from these examples are provided.

On the relative role of fire and rainfall in determining vegetation patterns in tropical savannas: a simulation study

Science.gov (United States)

Spessa, Allan; Fisher, Rosie

2010-05-01

LPJ-GUESS vegetation model. Recently, SPIFTIRE has been coupled to the Ecosystem Demography (ED) model, which simulates global vegetation dynamics as part of the new land surface scheme JULES (Joint UK Environment Simulator) within the QUEST Earth System Model (http://www.quest-esm.ac.uk/). This study forms part of on-going work to further improve and test the ability of JULES to accurately simulate the terrestrial carbon cycle and land-atmosphere exchanges under different climates. Using the JULES (ED-SPITFIRE) model driven by observed climate (1901-2002), and focusing on large-scale rainfall gradients in the tropical savannas of west Africa, the Northern Territory (Australia) and central-southern Brazil, this study assesses: i) simulated versus observed vegetation dynamics and distributions, and ii) the relative importance of fire versus rainfall in determining vegetation patterns. A sensitivity analysis approach was used.

Assessment of driving-related performance in chronic whiplash using an advanced driving simulator.

Science.gov (United States)

Takasaki, Hiroshi; Treleaven, Julia; Johnston, Venerina; Rakotonirainy, Andry; Haines, Andrew; Jull, Gwendolen

2013-11-01

Driving is often nominated as problematic by individuals with chronic whiplash associated disorders (WAD), yet driving-related performance has not been evaluated objectively. The purpose of this study was to test driving-related performance in persons with chronic WAD against healthy controls of similar age, gender and driving experience to determine if driving-related performance in the WAD group was sufficiently impaired to recommend fitness to drive assessment. Driving-related performance was assessed using an advanced driving simulator during three driving scenarios; freeway, residential and a central business district (CBD). Total driving duration was approximately 15min. Five driving tasks which could cause a collision (critical events) were included in the scenarios. In addition, the effect of divided attention (identify red dots projected onto side or rear view mirrors) was assessed three times in each scenario. Driving performance was measured using the simulator performance index (SPI) which is calculated from 12 measures. z-Scores for all SPI measures were calculated for each WAD subject based on mean values of the control subjects. The z-scores were then averaged for the WAD group. A z-score of ≤-2 indicated a driving failing grade in the simulator. The number of collisions over the five critical events was compared between the WAD and control groups as was reaction time and missed response ratio in identifying the red dots. Seventeen WAD and 26 control subjects commenced the driving assessment. Demographic data were comparable between the groups. All subjects completed the freeway scenario but four withdrew during the residential and eight during the CBD scenario because of motion sickness. All scenarios were completed by 14 WAD and 17 control subjects. Mean z-scores for the SPI over the three scenarios was statistically lower in the WAD group (-0.3±0.3; Pdriving. There were no differences in the reaction time and missed response ratio in divided

Effects of alcohol on attention orienting and dual-task performance during simulated driving: an event-related potential study.

Science.gov (United States)

Wester, Anne E; Verster, Joris C; Volkerts, Edmund R; Böcker, Koen B E; Kenemans, J Leon

2010-09-01

Driving is a complex task and is susceptible to inattention and distraction. Moreover, alcohol has a detrimental effect on driving performance, possibly due to alcohol-induced attention deficits. The aim of the present study was to assess the effects of alcohol on simulated driving performance and attention orienting and allocation, as assessed by event-related potentials (ERPs). Thirty-two participants completed two test runs in the Divided Attention Steering Simulator (DASS) with blood alcohol concentrations (BACs) of 0.00%, 0.02%, 0.05%, 0.08% and 0.10%. Sixteen participants performed the second DASS test run with a passive auditory oddball to assess alcohol effects on involuntary attention shifting. Sixteen other participants performed the second DASS test run with an active auditory oddball to assess alcohol effects on dual-task performance and active attention allocation. Dose-dependent impairments were found for reaction times, the number of misses and steering error, even more so in dual-task conditions, especially in the active oddball group. ERP amplitudes to novel irrelevant events were also attenuated in a dose-dependent manner. The P3b amplitude to deviant target stimuli decreased with blood alcohol concentration only in the dual-task condition. It is concluded that alcohol increases distractibility and interference from secondary task stimuli, as well as reduces attentional capacity and dual-task integrality.

Decoding the dopamine signal in macaque prefrontal cortex: a simulation study using the Cx3Dp simulator.

Directory of Open Access Journals (Sweden)

Isabelle Ayumi Spühler

Full Text Available Dopamine transmission in the prefrontal cortex plays an important role in reward based learning, working memory and attention. Dopamine is thought to be released non-synaptically into the extracellular space and to reach distant receptors through diffusion. This simulation study examines how the dopamine signal might be decoded by the recipient neuron. The simulation was based on parameters from the literature and on our own quantified, structural data from macaque prefrontal area 10. The change in extracellular dopamine concentration was estimated at different distances from release sites and related to the affinity of the dopamine receptors. Due to the sparse and random distribution of release sites, a transient heterogeneous pattern of dopamine concentration emerges. Our simulation predicts, however, that at any point in the simulation volume there is sufficient dopamine to bind and activate high-affinity dopamine receptors. We propose that dopamine is broadcast to its distant receptors and any change from the local baseline concentration might be decoded by a transient change in the binding probability of dopamine receptors. Dopamine could thus provide a graduated 'teaching' signal to reinforce concurrently active synapses and cell assemblies. In conditions of highly reduced or highly elevated dopamine levels the simulations predict that relative changes in the dopamine signal can no longer be decoded, which might explain why cognitive deficits are observed in patients with Parkinson's disease, or induced through drugs blocking dopamine reuptake.

Decoding the Dopamine Signal in Macaque Prefrontal Cortex: A Simulation Study Using the Cx3Dp Simulator

Science.gov (United States)

Spühler, Isabelle Ayumi; Hauri, Andreas

2013-01-01

Dopamine transmission in the prefrontal cortex plays an important role in reward based learning, working memory and attention. Dopamine is thought to be released non-synaptically into the extracellular space and to reach distant receptors through diffusion. This simulation study examines how the dopamine signal might be decoded by the recipient neuron. The simulation was based on parameters from the literature and on our own quantified, structural data from macaque prefrontal area 10. The change in extracellular dopamine concentration was estimated at different distances from release sites and related to the affinity of the dopamine receptors. Due to the sparse and random distribution of release sites, a transient heterogeneous pattern of dopamine concentration emerges. Our simulation predicts, however, that at any point in the simulation volume there is sufficient dopamine to bind and activate high-affinity dopamine receptors. We propose that dopamine is broadcast to its distant receptors and any change from the local baseline concentration might be decoded by a transient change in the binding probability of dopamine receptors. Dopamine could thus provide a graduated ‘teaching’ signal to reinforce concurrently active synapses and cell assemblies. In conditions of highly reduced or highly elevated dopamine levels the simulations predict that relative changes in the dopamine signal can no longer be decoded, which might explain why cognitive deficits are observed in patients with Parkinson’s disease, or induced through drugs blocking dopamine reuptake. PMID:23951205

Conducting Simulation Studies in the R Programming Environment

Directory of Open Access Journals (Sweden)

Kevin A. Hallgren

2013-10-01

Full Text Available Simulation studies allow researchers to answer specific questions about data analysis, statistical power, and best-practices for obtainingaccurate results in empirical research. Despite the benefits that simulation research can provide, many researchers are unfamiliar with available tools for conducting their own simulation studies. The use of simulation studies need not be restricted toresearchers with advanced skills in statistics and computer programming, and such methods can be implemented by researchers with a variety of abilities and interests. The present paper provides an introduction to methods used for running simulationstudies using the R statistical programming environment and is written for individuals with minimal experience running simulation studies or using R. The paper describes the rationale and benefits of using simulations and introduces R functions relevant for many simulation studies. Three examples illustrate different applications for simulation studies, including (a the use of simulations to answer a novel question about statistical analysis, (b the use of simulations to estimate statistical power, and (c the use of simulations to obtain confidence intervals of parameter estimates throughbootstrapping. Results and fully annotated syntax from these examples are provided.

Chernobyl reactor transient simulation study

International Nuclear Information System (INIS)

Gaber, F.A.; El Messiry, A.M.

1988-01-01

This paper deals with the Chernobyl nuclear power station transient simulation study. The Chernobyl (RBMK) reactor is a graphite moderated pressure tube type reactor. It is cooled by circulating light water that boils in the upper parts of vertical pressure tubes to produce steam. At equilibrium fuel irradiation, the RBMK reactor has a positive void reactivity coefficient. However, the fuel temperature coefficient is negative and the net effect of a power change depends upon the power level. Under normal operating conditions the net effect (power coefficient) is negative at full power and becomes positive under certain transient conditions. A series of dynamic performance transient analysis for RBMK reactor, pressurized water reactor (PWR) and fast breeder reactor (FBR) have been performed using digital simulator codes, the purpose of this transient study is to show that an accident of Chernobyl's severity does not occur in PWR or FBR nuclear power reactors. This appears from the study of the inherent, stability of RBMK, PWR and FBR under certain transient conditions. This inherent stability is related to the effect of the feed back reactivity. The power distribution stability in the graphite RBMK reactor is difficult to maintain throughout its entire life, so the reactor has an inherent instability. PWR has larger negative temperature coefficient of reactivity, therefore, the PWR by itself has a large amount of natural stability, so PWR is inherently safe. FBR has positive sodium expansion coefficient, therefore it has insufficient stability it has been concluded that PWR has safe operation than FBR and RBMK reactors

Discrete simulation and related fields. Proceedings of the IMACS European Simulation Meeting

Energy Technology Data Exchange (ETDEWEB)

Javor, A

1982-01-01

The following topics were dealt with: philosophy and methodology; flexible microprocessor systems; aggregative simulation system; directed simulation systems; directed simulation experiments; closed loop feedback controlled simulation system; system architecture; complex systems modelling and analysis; SIMKOM; artificial intelligence; forecasting of commodity flows; microprogrammed simulation; education systems; linear transformations; Cyber-72 input output subsystems; hazard detecting in MOS LSI circuits; and fault simulation for logic networks. 23 papers were presented, of which all are published in full in the present proceedings. Abstracts of individual papers can be found under the relevant classification in this or other issues.

Risk for intracranial pressure increase related to enclosed air in post-craniotomy patients during air ambulance transport: a retrospective cohort study with simulation.

Science.gov (United States)

Brändström, Helge; Sundelin, Anna; Hoseason, Daniela; Sundström, Nina; Birgander, Richard; Johansson, Göran; Winsö, Ola; Koskinen, Lars-Owe; Haney, Michael

2017-05-12

Post-craniotomy intracranial air can be present in patients scheduled for air ambulance transport to their home hospital. We aimed to assess risk for in-flight intracranial pressure (ICP) increases related to observed intracranial air volumes, hypothetical sea level pre-transport ICP, and different potential flight levels and cabin pressures. A cohort of consecutive subdural hematoma evacuation patients from one University Medical Centre was assessed with post-operative intracranial air volume measurements by computed tomography. Intracranial pressure changes related to estimated intracranial air volume effects of changing atmospheric pressure (simulating flight and cabin pressure changes up to 8000 ft) were simulated using an established model for intracranial pressure and volume relations. Approximately one third of the cohort had post-operative intracranial air. Of these, approximately one third had intracranial air volumes less than 11 ml. The simulation estimated that the expected changes in intracranial pressure during 'flight' would not result in intracranial hypertension. For intracranial air volumes above 11 ml, the simulation suggested that it was possible that intracranial hypertension could develop 'inflight' related to cabin pressure drop. Depending on the pre-flight intracranial pressure and air volume, this could occur quite early during the assent phase in the flight profile. DISCUSSION: These findings support the idea that there should be radiographic verification of the presence or absence of intracranial air after craniotomy for patients planned for long distance air transport. Very small amounts of air are clinically inconsequential. Otherwise, air transport with maintained ground-level cabin pressure should be a priority for these patients.

Simulations for Making On-farm Decisions in Relation to ENSO in Semi-arid Areas, South Africa

Science.gov (United States)

Tesfuhuney, W. A.; Crespo, O. O.; Walker, S. S.; Steyn, S. A.

2017-12-01

The study was employed to investigate and improve on-farm decision making on planting dates and fertilization by relating simulated yield and seasonal outlook information. The Agricultural Production Systems SIMulator model (APSIM) was used to explore ENSO/SOI effects for small-scale farmers to represent weather conditions and soil forms of semi-arid areas of Bothaville, Bethlehem and Bloemfontein regions in South Africa. The relationships of rainfall and SOI anomalies indicate a positive correlation, signifies ENSO/SOI as seasonal outlooks for study areas. Model evaluation results showed higher degree of bias (RMSEs/RMSE value of 0.88-0.98). The D-index of agreement in the range 0.61-0.71 indicate the ability of the APSIM-Maize model is an adequate tool in evaluating relative changes in maize yield in relation to various management practices and seasonal variations. During rainy, La Niño years (SOI > +5), highest simulated yields were found for Bethlehem in November with addition of 100 - 150 kg ha-1 N fertilization and up to 50 kg ha-1 for both Bothaville and Bloemfontein. With respect to various levels of fertilization, the dry El Niño years (SOI risk for dryland farming in semi-arid regions. Key word: Semi-arid; APSIM; SOI; El Niño / La Niña; On-farm Decisions

Conducting Simulation Studies in Psychometrics

Science.gov (United States)

Feinberg, Richard A.; Rubright, Jonathan D.

2016-01-01

Simulation studies are fundamental to psychometric discourse and play a crucial role in operational and academic research. Yet, resources for psychometricians interested in conducting simulations are scarce. This Instructional Topics in Educational Measurement Series (ITEMS) module is meant to address this deficiency by providing a comprehensive…

Numerical relativity simulations of precessing binary neutron star mergers

Science.gov (United States)

Dietrich, Tim; Bernuzzi, Sebastiano; Brügmann, Bernd; Ujevic, Maximiliano; Tichy, Wolfgang

2018-03-01

We present the first set of numerical relativity simulations of binary neutron mergers that include spin precession effects and are evolved with multiple resolutions. Our simulations employ consistent initial data in general relativity with different spin configurations and dimensionless spin magnitudes ˜0.1 . They start at a gravitational-wave frequency of ˜392 Hz and cover more than 1 precession period and about 15 orbits up to merger. We discuss the spin precession dynamics by analyzing coordinate trajectories, quasilocal spin measurements, and energetics, by comparing spin aligned, antialigned, and irrotational configurations. Gravitational waveforms from different spin configuration are compared by calculating the mismatch between pairs of waveforms in the late inspiral. We find that precession effects are not distinguishable from nonprecessing configurations with aligned spins for approximately face-on binaries, while the latter are distinguishable from nonspinning configurations. Spin precession effects are instead clearly visible for approximately edge-on binaries. For the parameters considered here, precession does not significantly affect the characteristic postmerger gravitational-wave frequencies nor the mass ejection. Our results pave the way for the modeling of spin precession effects in the gravitational waveform from binary neutron star events.

Relative importance of secondary settling tank models in WWTP simulations

DEFF Research Database (Denmark)

Ramin, Elham; Flores-Alsina, Xavier; Sin, Gürkan

2012-01-01

Results obtained in a study using the Benchmark Simulation Model No. 1 (BSM1) show that a one-dimensional secondary settling tank (1-D SST) model structure and its parameters are among the most significant sources of uncertainty in wastewater treatment plant (WWTP) simulations [Ramin et al., 2011......]. The sensitivity results consistently indicate that the prediction of sludge production is most sensitive to the variation of the settling parameters. In the present study, we use the Benchmark Simulation Model No. 2 (BSM2), a plant-wide benchmark, that combines the Activated Sludge Model No. 1 (ASM1...

New media simulation stories in nursing education: a quasi-experimental study exploring learning outcomes.

Science.gov (United States)

Webb-Corbett, Robin; Schwartz, Melissa Renee; Green, Bob; Sessoms, Andrea; Swanson, Melvin

2013-04-01

New media simulation stories are short multimedia presentations that combine simulation, digital technology, and story branching to depict a variety of healthcare-related scenarios. The purpose of this study was to explore whether learning outcomes were enhanced if students viewed the results of both correct and incorrect nursing actions demonstrated through new media simulation stories. A convenience sample of 109 undergraduate nursing students in a family-centered maternity course participated in the study. Study findings suggests that students who viewed both correct and incorrect depictions of maternity nursing actions scored better on tests than did those students who viewed only correct nursing actions.

Publicly Open Virtualized Gaming Environment For Simulation of All Aspects Related to '100 Year Starship Study'

Science.gov (United States)

Obousy, R. K.

2012-09-01

Sending a mission to distant stars will require our civilization to develop new technologies and change the way we live. The complexity of the task is enormous [1] thus, the thought is to involve people from around the globe through the ``citizen scientist'' paradigm. The suggestion is a ``Gaming Virtual Reality Network'' (GVRN) to simulate sociological and technological aspects involved in this project. Currently there is work being done [2] in developing a technology which will construct computer games within GVRN. This technology will provide quick and easy ways for individuals to develop game scenarios related to various aspects of the ``100YSS'' project. People will be involved in solving certain tasks just by play games. Players will be able to modify conditions, add new technologies, geological conditions, social movements and assemble new strategies just by writing scenarios. The system will interface with textual and video information, extract scenarios written in millions of texts and use it to assemble new games. Thus, players will be able to simulate enormous amounts of possibilities. Information technologies will be involved which will require us to start building the system in a way that any modules can be easily replaced. Thus, GVRN should be modular and open to the community.

The energy and stability of helium-related cluster in nickel: A study of molecular dynamics simulation

Energy Technology Data Exchange (ETDEWEB)

Gong, Hengfeng, E-mail: gonghengfeng@sinap.ac.cn [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Division of Nuclear Materials and Engineering, Shanghai 201800 (China); Key Laboratory of Interfacial Physics and Technology, Chinese Academy of Sciences, Shanghai 201800 (China); Wang, Chengbin; Zhang, Wei; Xu, Jian [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Division of Nuclear Materials and Engineering, Shanghai 201800 (China); Key Laboratory of Interfacial Physics and Technology, Chinese Academy of Sciences, Shanghai 201800 (China); Huai, Ping, E-mail: huaiping@sinap.ac.cn [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Division of Nuclear Materials and Engineering, Shanghai 201800 (China); Key Laboratory of Nuclear Radiation and Nuclear Energy Technology, Chinese Academy of Sciences, Shanghai 201800 (China); Deng, Huiqiu; Hu, Wangyu [Hunan University, Department of Applied Physics, Changsha 410082 (China)

2016-02-01

Highlights: • The He-related clusters exhibit the very high symmetry. • The trapping capability of vacancy to defects becomes weak due to the pre-existed SIA. • The average length of He{sub N}V{sub 1} clusters is longer than one of He{sub N} and He{sub N}V{sub 1}SIA{sub 1} cluster. - Abstract: Using molecular dynamics simulation, we investigated the energy and stability of helium-related cluster in nickel. All the binding energies of the He-related clusters are demonstrated to be positive and increase with the cluster sizes. Due to the pre-existed self-interstitial nickel atom, the trapping capability of vacancy to defects becomes weak. Besides, the minimum energy configurations of He-related clusters exhibit the very high symmetry in the local atomistic environment. And for the He{sub N} and He{sub N}V{sub 1}SIA{sub 1} clusters, the average length of He–He bonds shortens, but it elongates for the He{sub N}V{sub 1} clusters with helium cluster sizes. The helium-to-vacancy ratio plays a decisive role on the binding energies of He{sub N}V{sub M} cluster. These results can provide some excellent clues to insight the initial stage of helium bubbles nucleation and growth in the Ni-based alloys for the Generation-IV Molten Salt Reactor.

Parameter uncertainty in simulations of extreme precipitation and attribution studies.

Science.gov (United States)

Timmermans, B.; Collins, W. D.; O'Brien, T. A.; Risser, M. D.

2017-12-01

The attribution of extreme weather events, such as heavy rainfall, to anthropogenic influence involves the analysis of their probability in simulations of climate. The climate models used however, such as the Community Atmosphere Model (CAM), employ approximate physics that gives rise to "parameter uncertainty"—uncertainty about the most accurate or optimal values of numerical parameters within the model. In particular, approximate parameterisations for convective processes are well known to be influential in the simulation of precipitation extremes. Towards examining the impact of this source of uncertainty on attribution studies, we investigate the importance of components—through their associated tuning parameters—of parameterisations relating to deep and shallow convection, and cloud and aerosol microphysics in CAM. We hypothesise that as numerical resolution is increased the change in proportion of variance induced by perturbed parameters associated with the respective components is consistent with the decreasing applicability of the underlying hydrostatic assumptions. For example, that the relative influence of deep convection should diminish as resolution approaches that where convection can be resolved numerically ( 10 km). We quantify the relationship between the relative proportion of variance induced and numerical resolution by conducting computer experiments that examine precipitation extremes over the contiguous U.S. In order to mitigate the enormous computational burden of running ensembles of long climate simulations, we use variable-resolution CAM and employ both extreme value theory and surrogate modelling techniques ("emulators"). We discuss the implications of the relationship between parameterised convective processes and resolution both in the context of attribution studies and progression towards models that fully resolve convection.

Participatory ergonomics simulation of hospital work systems: The influence of simulation media on simulation outcome.

Science.gov (United States)

Andersen, Simone Nyholm; Broberg, Ole

2015-11-01

Current application of work system simulation in participatory ergonomics (PE) design includes a variety of different simulation media. However, the actual influence of the media attributes on the simulation outcome has received less attention. This study investigates two simulation media: full-scale mock-ups and table-top models. The aim is to compare, how the media attributes of fidelity and affordance influence the ergonomics identification and evaluation in PE design of hospital work systems. The results illustrate, how the full-scale mock-ups' high fidelity of room layout and affordance of tool operation support ergonomics identification and evaluation related to the work system entities space and technologies & tools. The table-top models' high fidelity of function relations and affordance of a helicopter view support ergonomics identification and evaluation related to the entity organization. Furthermore, the study addresses the form of the identified and evaluated conditions, being either identified challenges or tangible design criteria. Copyright © 2015 Elsevier Ltd and The Ergonomics Society. All rights reserved.

The effects of a simulated laughter programme on mood, cortisol levels, and health-related quality of life among haemodialysis patients.

Science.gov (United States)

Heo, Eun Hwa; Kim, Sehyun; Park, Hye-Ja; Kil, Suk Yong

2016-11-01

This study aimed to evaluate the effects of a simulated laughter programme on mood, cortisol levels, and health-related quality of life among haemodialysis patients. Forty participants were randomly assigned to a laughter group (n = 20) or a control group (n = 20). Eleven participants completed the laughter programme after haemodialysis sessions and 18 control participants remained. The 4-week simulated laughter programme included weekly 60 min group sessions of simulated laughter, breathing, stretching exercises, and meditation, as well as daily 15 s individual laughter sessions administered via telephone. Mood, cortisol levels, and health-related quality of life were analysed using the rank analysis of covariance, and Wilcoxon's signed rank test. The laughter group exhibited improvements in mood, symptoms, social interaction quality, and role limitations due to physical health. The simulated laughter programme may help improve mood and health-related quality of life among haemodialysis patients. Copyright © 2016 Elsevier Ltd. All rights reserved.

A task-related and resting state realistic fMRI simulator for fMRI data validation

Science.gov (United States)

Hill, Jason E.; Liu, Xiangyu; Nutter, Brian; Mitra, Sunanda

2017-02-01

After more than 25 years of published functional magnetic resonance imaging (fMRI) studies, careful scrutiny reveals that most of the reported results lack fully decisive validation. The complex nature of fMRI data generation and acquisition results in unavoidable uncertainties in the true estimation and interpretation of both task-related activation maps and resting state functional connectivity networks, despite the use of various statistical data analysis methodologies. The goal of developing the proposed STANCE (Spontaneous and Task-related Activation of Neuronally Correlated Events) simulator is to generate realistic task-related and/or resting-state 4D blood oxygenation level dependent (BOLD) signals, given the experimental paradigm and scan protocol, by using digital phantoms of twenty normal brains available from BrainWeb (http://brainweb.bic.mni.mcgill.ca/brainweb/). The proposed simulator will include estimated system and modelled physiological noise as well as motion to serve as a reference to measured brain activities. In its current form, STANCE is a MATLAB toolbox with command line functions serving as an open-source add-on to SPM8 (http://www.fil.ion.ucl.ac.uk/spm/software/spm8/). The STANCE simulator has been designed in a modular framework so that the hemodynamic response (HR) and various noise models can be iteratively improved to include evolving knowledge about such models.

A simulation study comparing aberration detection algorithms for syndromic surveillance

Directory of Open Access Journals (Sweden)

Painter Ian

2007-03-01

Full Text Available Abstract Background The usefulness of syndromic surveillance for early outbreak detection depends in part on effective statistical aberration detection. However, few published studies have compared different detection algorithms on identical data. In the largest simulation study conducted to date, we compared the performance of six aberration detection algorithms on simulated outbreaks superimposed on authentic syndromic surveillance data. Methods We compared three control-chart-based statistics, two exponential weighted moving averages, and a generalized linear model. We simulated 310 unique outbreak signals, and added these to actual daily counts of four syndromes monitored by Public Health – Seattle and King County's syndromic surveillance system. We compared the sensitivity of the six algorithms at detecting these simulated outbreaks at a fixed alert rate of 0.01. Results Stratified by baseline or by outbreak distribution, duration, or size, the generalized linear model was more sensitive than the other algorithms and detected 54% (95% CI = 52%–56% of the simulated epidemics when run at an alert rate of 0.01. However, all of the algorithms had poor sensitivity, particularly for outbreaks that did not begin with a surge of cases. Conclusion When tested on county-level data aggregated across age groups, these algorithms often did not perform well in detecting signals other than large, rapid increases in case counts relative to baseline levels.

Simulating Navigation with Virtual 3d Geovisualizations - a Focus on Memory Related Factors

Science.gov (United States)

Lokka, I.; Çöltekin, A.

2016-06-01

The use of virtual environments (VE) for navigation-related studies, such as spatial cognition and path retrieval has been widely adopted in cognitive psychology and related fields. What motivates the use of VEs for such studies is that, as opposed to real-world, we can control for the confounding variables in simulated VEs. When simulating a geographic environment as a virtual world with the intention to train navigational memory in humans, an effective and efficient visual design is important to facilitate the amount of recall. However, it is not yet clear what amount of information should be included in such visual designs intended to facilitate remembering: there can be too little or too much of it. Besides the amount of information or level of detail, the types of visual features (`elements' in a visual scene) that should be included in the representations to create memorable scenes and paths must be defined. We analyzed the literature in cognitive psychology, geovisualization and information visualization, and identified the key factors for studying and evaluating geovisualization designs for their function to support and strengthen human navigational memory. The key factors we identified are: i) the individual abilities and age of the users, ii) the level of realism (LOR) included in the representations and iii) the context in which the navigation is performed, thus specific tasks within a case scenario. Here we present a concise literature review and our conceptual development for follow-up experiments.

Participatory ergonomics simulation of hospital work systems: The influence of simulation media on simulation outcome

DEFF Research Database (Denmark)

Andersen, Simone Nyholm; Broberg, Ole

2015-01-01

of tool operation support ergonomics identification and evaluation related to the work system entities space and technologies & tools. The table-top models’ high fidelity of function relations and affordance of a helicopter view support ergonomics identification and evaluation related to the entity......Current application of work system simulation in participatory ergonomics (PE) design includes a variety of different simulation media. However, the actual influence of the media attributes on the simulation outcome has received less attention. This study investigates two simulation media: full......-scale mock-ups and table-top models. The aim is to compare, how the media attributes of fidelity and affordance influence the ergonomics identification and evaluation in PE design of hospital work systems. The results illustrate, how the full-scale mock-ups’ high fidelity of room layout and affordance...

Comprehensive gyrokinetic simulation of tokamak turbulence at finite relative gyroradius

International Nuclear Information System (INIS)

Waltz, R.E.; Candy, J.; Rosenbluth, M.N.

2003-01-01

A continuum global gyrokinetic code GYRO has been developed to comprehensively simulate turbulent transport in actual experimental profiles and allow direct quantitative comparisons to the experimental transport flows. GYRO not only treats the now standard ion temperature gradient (ITG) mode turbulence, but also treats trapped and passing electrons with collisions and finite beta, and all in real tokamak geometry. Most importantly the code operates at finite relative gyroradius (ρ*) so as to treat the profile shear stabilization effects which break gyro Bohm scaling. The code operates in a cyclic flux tube limit which allows only gyro Bohm scaling and a noncylic radial annulus with physical profile variation. The later requires an adaptive source to maintain equilibrium profiles. Simple ITG simulations demonstrate the broken gyro Bohm scaling paradigm of Garbet and Waltz [Phys. Plasmas 3, 1898 (1996)]. Since broken gyro Bohm scaling depends on the actual rotational velocity shear rates competing with mode growth rates, direct comprehensive simulations of the DIII-D ρ*-scaled L-mode experiments are presented as a quantitative test of gyrokinetics and the paradigm. (author)

Mathematical and Computational Aspects Related to Soil Modeling and Simulation

Science.gov (United States)

2017-09-26

and simulation challenges at the interface of applied math (homogenization, handling of discontinuous behavior, discrete vs. continuum representations...topics: a) Visco-elasto-plastic continuum models of geo-surface materials b) Discrete models of geo-surface materials (rocks/gravel/sand) c) Mixed...continuum- discrete representations. Coarse-graining and fine-graining mathematical formulations d) Multi-physics aspects related to the modeling of

Multivariate Meta-Analysis of Genetic Association Studies: A Simulation Study.

Directory of Open Access Journals (Sweden)

Binod Neupane

Full Text Available In a meta-analysis with multiple end points of interests that are correlated between or within studies, multivariate approach to meta-analysis has a potential to produce more precise estimates of effects by exploiting the correlation structure between end points. However, under random-effects assumption the multivariate estimation is more complex (as it involves estimation of more parameters simultaneously than univariate estimation, and sometimes can produce unrealistic parameter estimates. Usefulness of multivariate approach to meta-analysis of the effects of a genetic variant on two or more correlated traits is not well understood in the area of genetic association studies. In such studies, genetic variants are expected to roughly maintain Hardy-Weinberg equilibrium within studies, and also their effects on complex traits are generally very small to modest and could be heterogeneous across studies for genuine reasons. We carried out extensive simulation to explore the comparative performance of multivariate approach with most commonly used univariate inverse-variance weighted approach under random-effects assumption in various realistic meta-analytic scenarios of genetic association studies of correlated end points. We evaluated the performance with respect to relative mean bias percentage, and root mean square error (RMSE of the estimate and coverage probability of corresponding 95% confidence interval of the effect for each end point. Our simulation results suggest that multivariate approach performs similarly or better than univariate method when correlations between end points within or between studies are at least moderate and between-study variation is similar or larger than average within-study variation for meta-analyses of 10 or more genetic studies. Multivariate approach produces estimates with smaller bias and RMSE especially for the end point that has randomly or informatively missing summary data in some individual studies, when

A review on the relation between simulation and improvement in hospitals

Directory of Open Access Journals (Sweden)

van Lent Wineke AM

2012-03-01

Full Text Available Abstract Background Simulation applications on operations management in hospitals are frequently published and claim to support decision-making on operations management subjects. However, the reported implementation rates of recommendations are low and the actual impact of the changes recommended by the modeler has hardly been examined. This paper examines: 1 the execution rate of simulation study recommendations, 2 the research methods used to evaluate implementation of recommendations, 3 factors contributing to implementation, and 4 the differences regarding implementation between literature and practice. Results Altogether 16 hospitals executed the recommendations (at least partially. Implementation results were hardly reported upon; 1 study described a before-and-after design, 2 a partial before and after design. Factors that help implementation were grouped according to 1 technical quality, of which data availability, validation/verification with historic data/expert opinion, and the development of the conceptual model were mentioned most frequently 2 process quality, with client involvement and 3 outcome quality with, presentation of results. The survey response rate of traceable authors was 61%, 18 authors implemented the results at least partially. Among these responses, evaluation methods were relatively better with 3 time series designs and 2 before-and-after designs. Conclusions Although underreported in literature, implementation of recommendations seems limited; this review provides recommendations on project design, implementation conditions and evaluation methods to increase implementation. Methods A literature review in PubMed and Business Source Elite on stochastic simulation applications on operations management in individual hospitals published between 1997 and 2008. From those reporting implementation, cross references were added. In total, 89 papers were included. A scoring list was used for data extraction. Two reviewers

Studies on Fracture Behavior of Epoxy/DWNT Nanocomposites by Molecular Dynamics Simulation

Directory of Open Access Journals (Sweden)

Shahin Shadlou

2012-12-01

Full Text Available The nanoscale fracture behavior of epoxy-based nanocomposites reinforced with double-walled carbon nanotube (DWNT was investigated by molecular dynamics (MD simulations technique. In order to prepare a nanocomposite model including polymer and DWNT, the exact atomic structure of epoxy was adopted as in previous experimental studies made by authors. Tersoff and Amber potential, which are well known potentials, were used for simulation of polymer and DWNT, respectively. Among different available methods to simulate the cross-linking process, a technique was adopted with closer similarity to what happens in real conditions. Therefore, when some especial atoms of monomer and hardener molecules were closer than a specific potential distance, the chemical bonds were created between them. To verify the prepared model, a pull-out simulation was carried out and the results were compared with those of previous studies. It was found that although a rather wide range for interface strength has been presented by different researchers and different techniques, the strength obtained in this study is in the middle of this range. In addition, the fracture energy obtained from the simulations for pure epoxy was compared with that of experimental results and good agreement was obtained. To evaluate the effect of nanocomposite structure at nanometer scale, DWNT was modeled in three different angles relative to the loading direction, including 0°, 45°and 90°. It was found that when DWNT is parallel with the loading direction (i.e. 90° it has the least impact on the fracture energy. The maximum fracture energy was obtained when MWNT was at 45° relative to loading direction. These results were compared with the theories provided for conventional composites.

A study on a nano-scale materials simulation using a PC cluster

International Nuclear Information System (INIS)

Choi, Deok Kee; Ryu, Han Kyu

2002-01-01

Not a few scientists have paid attention to application of molecular dynamics to chemistry, biology and physics. With recent popularity of nano technology, nano-scale analysis has become a major subject in various engineering fields. A underlying nano scale analysis is based on classical molecular theories representing molecular dynamics. Based on Newton's law of motions of particles, the movement of each particles is to be determined by numerical integrations. As the size of computation is closely related with the number of molecules, materials simulation takes up huge amount of computer resources so that it is not until recent days that the application of molecular dynamics to materials simulations draw some attention from many researchers. Thanks to high-performance computers, materials simulation via molecular dynamics looks promising. In this study, a PC cluster consisting of multiple commodity PCs is established and nano scale materials simulations are carried out. Micro-sized crack propagation inside a nano material is displayed by the simulation

Simulating the market coefficient of relative risk aversion

Directory of Open Access Journals (Sweden)

Samih Antoine Azar

2014-12-01

Full Text Available In this paper, expected utility, defined by a Taylor series expansion around expected wealth, is maximized. The coefficient of relative risk aversion (CRRA that is commensurate with a 100% investment in the risky asset is simulated. The following parameters are varied: the riskless return, the market standard deviation, the market stock premium, and the skewness and the kurtosis of the risky return. Both the high extremes and the low extremes are considered. With these figures, the upper bound of the market CRRA is 3.021 and the lower bound is 0.466. Log utility, which corresponds to a CRRA of 1, is not excluded.

Multipebble Simulations for Alternating Automata

Science.gov (United States)

Clemente, Lorenzo; Mayr, Richard

We study generalized simulation relations for alternating Büchi automata (ABA), as well as alternating finite automata. Having multiple pebbles allows the Duplicator to "hedge her bets" and delay decisions in the simulation game, thus yielding a coarser simulation relation. We define (k 1,k 2)-simulations, with k 1/k 2 pebbles on the left/right, respectively. This generalizes previous work on ordinary simulation (i.e., (1,1)-simulation) for nondeterministic Büchi automata (NBA)[4] in and ABA in [5], and (1,k)-simulation for NBA in [3].

Fact or factitious? A psychobiological study of authentic and simulated dissociative identity states.

Science.gov (United States)

Reinders, A A T S; Reinders, A A T Simone; Willemsen, Antoon T M; Vos, Herry P J; den Boer, Johan A; Nijenhuis, Ellert R S

2012-01-01

Dissociative identity disorder (DID) is a disputed psychiatric disorder. Research findings and clinical observations suggest that DID involves an authentic mental disorder related to factors such as traumatization and disrupted attachment. A competing view indicates that DID is due to fantasy proneness, suggestibility, suggestion, and role-playing. Here we examine whether dissociative identity state-dependent psychobiological features in DID can be induced in high or low fantasy prone individuals by instructed and motivated role-playing, and suggestion. DID patients, high fantasy prone and low fantasy prone controls were studied in two different types of identity states (neutral and trauma-related) in an autobiographical memory script-driven (neutral or trauma-related) imagery paradigm. The controls were instructed to enact the two DID identity states. Twenty-nine subjects participated in the study: 11 patients with DID, 10 high fantasy prone DID simulating controls, and 8 low fantasy prone DID simulating controls. Autonomic and subjective reactions were obtained. Differences in psychophysiological and neural activation patterns were found between the DID patients and both high and low fantasy prone controls. That is, the identity states in DID were not convincingly enacted by DID simulating controls. Thus, important differences regarding regional cerebral bloodflow and psychophysiological responses for different types of identity states in patients with DID were upheld after controlling for DID simulation. The findings are at odds with the idea that differences among different types of dissociative identity states in DID can be explained by high fantasy proneness, motivated role-enactment, and suggestion. They indicate that DID does not have a sociocultural (e.g., iatrogenic) origin.

A framework for simulating ultrasound imaging based on first order nonlinear pressure–velocity relations

DEFF Research Database (Denmark)

Du, Yigang; Fan, Rui; Li, Yong

2016-01-01

An ultrasound imaging framework modeled with the first order nonlinear pressure–velocity relations (NPVR) based simulation and implemented by a half-time staggered solution and pseudospectral method is presented in this paper. The framework is capable of simulating linear and nonlinear ultrasound...... propagation and reflections in a heterogeneous medium with different sound speeds and densities. It can be initialized with arbitrary focus, excitation and apodization for multiple individual channels in both 2D and 3D spatial fields. The simulated channel data can be generated using this framework......, and ultrasound image can be obtained by beamforming the simulated channel data. Various results simulated by different algorithms are illustrated for comparisons. The root mean square (RMS) errors for each compared pulses are calculated. The linear propagation is validated by an angular spectrum approach (ASA...

Survival of Listeria monocytogenes in simulated gastrointestinal system and transcriptional profiling of stress- and adhesion-related genes

DEFF Research Database (Denmark)

Jiang, Lingli; Olesen, Inger; Andersen, Thomas

2010-01-01

-related genes after exposure to the conditions similar to those encountered in the mouth, stomach, and small intestine. None of the L. monocytogenes strains investigated could survive in the gastric juice at pH 2.5 or 3.0. Their survival increased at higher pH (3.5 and 4.0) in the gastric stress. Relative...... afterpassing through the simulated gastrointestinal tract, whereas that of the adhesion-related gene ami was downregulated. Taken together, this study revealed that L. monocytogenes strains enhanced the expression of stressrelated genes and decreased the transcription of adhesion-related gene in order...

A simulation study of enhancement duration in three-dimensional contrast-enhanced MR angiography

International Nuclear Information System (INIS)

Ohkubo, Masaki; Ohgoshi, Yukio; Inoue, Tomoko; Naito, Kenichi; Suzuki, Kiyotaka

2001-01-01

In our study on three-dimensional (3D) contrast-enhanced MR angiography we performed a computer simulation to investigate quantitative vessel visibility. In the simulation, we evaluated the relative loss of signal intensity in a vessel due to shortened duration of contrast-enhancement. The mid-point of enhancement-duration was assumed to be at the point in which the data in the center of k-space (k y axis) was acquired. Signal intensity of a vessel decreased as the enhancement-duration was shortened and the diameter of the vessel was decreased. When the duration was shortened 40%, the signal intensity of a vessel in which the diameter was more than 2 pixels was preserved by approximately 70% or more. This suggests that the vessel visibility is high. When the duration was shortened 20%, the signal intensity of a vessel in which the diameter was less than 2 pixels decreased to less than approximately 40% or less. The simulation was confirmed by using 3D MR angiography with a tube phantom filled with Gd-DTPA to simulate a vessel model. At anytime during data acquisition, we could set the phantom on the region being scanned or take it out by using the ''pause'' function of the MR scanner. This made it possible to change the enhancement-duration to match the simulation. Results of the phantom study were comparable to those of the simulation, suggesting that the simulation was valid. Our results and simple techniques for both the simulation and the phantom study using the ''pause'' function, were considered useful in the study of 3D MR angiography. (author)

Simulation-Based Evaluation of the Performances of an Algorithm for Detecting Abnormal Disease-Related Features in Cattle Mortality Records.

Science.gov (United States)

Perrin, Jean-Baptiste; Durand, Benoît; Gay, Emilie; Ducrot, Christian; Hendrikx, Pascal; Calavas, Didier; Hénaux, Viviane

2015-01-01

We performed a simulation study to evaluate the performances of an anomaly detection algorithm considered in the frame of an automated surveillance system of cattle mortality. The method consisted in a combination of temporal regression and spatial cluster detection which allows identifying, for a given week, clusters of spatial units showing an excess of deaths in comparison with their own historical fluctuations. First, we simulated 1,000 outbreaks of a disease causing extra deaths in the French cattle population (about 200,000 herds and 20 million cattle) according to a model mimicking the spreading patterns of an infectious disease and injected these disease-related extra deaths in an authentic mortality dataset, spanning from January 2005 to January 2010. Second, we applied our algorithm on each of the 1,000 semi-synthetic datasets to identify clusters of spatial units showing an excess of deaths considering their own historical fluctuations. Third, we verified if the clusters identified by the algorithm did contain simulated extra deaths in order to evaluate the ability of the algorithm to identify unusual mortality clusters caused by an outbreak. Among the 1,000 simulations, the median duration of simulated outbreaks was 8 weeks, with a median number of 5,627 simulated deaths and 441 infected herds. Within the 12-week trial period, 73% of the simulated outbreaks were detected, with a median timeliness of 1 week, and a mean of 1.4 weeks. The proportion of outbreak weeks flagged by an alarm was 61% (i.e. sensitivity) whereas one in three alarms was a true alarm (i.e. positive predictive value). The performances of the detection algorithm were evaluated for alternative combination of epidemiologic parameters. The results of our study confirmed that in certain conditions automated algorithms could help identifying abnormal cattle mortality increases possibly related to unidentified health events.

Designing and Simulation of a Two-Axis Solar Tracking System by Exact Relations of Solar Angles

Directory of Open Access Journals (Sweden)

Faezeh Esmaili Ranjbar

2013-01-01

Full Text Available In this study, a system has been designed and simulated to track sunlight, which identifies sun location based on the exact relations of solar angles and without any optical sensor. In fact the relations which have been used in this study are far more accurate compared to similar cases, because of using the "equation of time" and reducing the tracking time of every 15 minutes. In this system, an economical micro-controller has been used to generate the necessary orders to control system and two stepper motors for powering solar array. By adding a real-time clock IC (RTC to angle differentiation circuit, dynamic plane has improved.

Preliminary simulation study of doppler reflectometry

International Nuclear Information System (INIS)

Ishii, Yuta; Hojo, Hitoshi; Yoshikawa, Masashi; Ichimura, Makoto; Haraguchi, Yusuke; Imai, Tsuyoshi; Mase, Atsushi

2010-01-01

A preliminary simulation study of Doppler reflectometry is performed. The simulations solve Maxwell's equations by a finite difference time domain (FDTD) code method in two dimensions. A moving corrugated metal target is used as a plasma cutoff layer to study the basic features of Doppler reflectometry. We examined the effects of the full width at half maximum (FWHM) of the electromagnetic waves and the corrugation depth of the metal target. Furthermore, the effect of a nonuniform plasma is studied using this FDTD analysis. The Doppler shift and velocity are compared with those obtained from FDTD analysis of a uniform plasma. (author)

Simulation-Based Approach for Studying the Balancing of Local Smart Grids with Electric Vehicle Batteries

Directory of Open Access Journals (Sweden)

Juhani Latvakoski

2015-07-01

Full Text Available Modern society is facing great challenges due to pollution and increased carbon dioxide (CO2 emissions. As part of solving these challenges, the use of renewable energy sources and electric vehicles (EVs is rapidly increasing. However, increased dynamics have triggered problems in balancing energy supply and consumption demand in the power systems. The resulting uncertainty and unpredictability of energy production, consumption, and management of peak loads has caused an increase in costs for energy market actors. Therefore, the means for studying the balancing of local smart grids with EVs is a starting point for this paper. The main contribution is a simulation-based approach which was developed to enable the study of the balancing of local distribution grids with EV batteries in a cost-efficient manner. The simulation-based approach is applied to enable the execution of a distributed system with the simulation of a local distribution grid, including a number of charging stations and EVs. A simulation system has been constructed to support the simulation-based approach. The evaluation has been carried out by executing the scenario related to balancing local distribution grids with EV batteries in a step-by-step manner. The evaluation results indicate that the simulation-based approach is able to facilitate the evaluation of smart grid– and EV-related communication protocols, control algorithms for charging, and functionalities of local distribution grids as part of a complex, critical cyber-physical system. In addition, the simulation system is able to incorporate advanced methods for monitoring, controlling, tracking, and modeling behavior. The simulation model of the local distribution grid can be executed with the smart control of charging and discharging powers of the EVs according to the load situation in the local distribution grid. The resulting simulation system can be applied to the study of balancing local smart grids with EV

Vertical Motion Changes Related to North-East Brazil Rainfall Variability: a GCM Simulation

Science.gov (United States)

Roucou, Pascal; Oribe Rocha de Aragão, José; Harzallah, Ali; Fontaine, Bernard; Janicot, Serge

1996-08-01

The atmospheric structure over north-east Brazil during anomalous rainfall years is studied in the 11 levels of the outputs of the Laboratoire de Météorologie Dynamique atmospheric general circulation model (LMD AGCM). Seven 19-year simulations were performed using observed sea-surface temperature (SST) corresponding to the period 1970- 1988. The ensemble mean is calculated for each month of the period, leading to an ensemble-averaged simulation. The simulated March-April rainfall is in good agreement with observations. Correlations of simulated rainfall and three SST indices relative to the equatorial Pacific and northern and southern parts of the Atlantic Ocean exhibit stronger relationships in the simulation than in the observations. This is particularly true with the SST gradient in the Atlantic (Atlantic dipole). Analyses on 200 ;hPa velocity potential, vertical velocity, and vertical integral of the zonal component of mass flux are performed for years of abnormal rainfall and positive/negative SST anomalies in the Pacific and Atlantic oceans in March-April during the rainy season over the Nordeste region. The results at 200 hPa show a convergence anomaly over Nordeste and a divergence anomaly over the Pacific concomitant with dry seasons associated with warm SST anomalies in the Pacific and warm (cold) waters in the North (South) Atlantic. During drought years convection inside the ITCZ indicated by the vertical velocity exhibits a displacement of the convection zone corresponding to a northward migration of the ITCZ. The east-west circulation depicted by the zonal divergent mass flux shows subsiding motion over Nordeste and ascending motion over the Pacific in drought years, accompanied by warm waters in the eastern Pacific and warm/cold waters in northern/southern Atlantic. Rainfall variability of the Nordeste rainfall is linked mainly to vertical motion and SST variability through the migration of the ITCZ and the east-west circulation.

Virtual reality simulation training of mastoidectomy - studies on novice performance.

Science.gov (United States)

Andersen, Steven Arild Wuyts

2016-08-01

Virtual reality (VR) simulation-based training is increasingly used in surgical technical skills training including in temporal bone surgery. The potential of VR simulation in enabling high-quality surgical training is great and VR simulation allows high-stakes and complex procedures such as mastoidectomy to be trained repeatedly, independent of patients and surgical tutors, outside traditional learning environments such as the OR or the temporal bone lab, and with fewer of the constraints of traditional training. This thesis aims to increase the evidence-base of VR simulation training of mastoidectomy and, by studying the final-product performances of novices, investigates the transfer of skills to the current gold-standard training modality of cadaveric dissection, the effect of different practice conditions and simulator-integrated tutoring on performance and retention of skills, and the role of directed, self-regulated learning. Technical skills in mastoidectomy were transferable from the VR simulation environment to cadaveric dissection with significant improvement in performance after directed, self-regulated training in the VR temporal bone simulator. Distributed practice led to a better learning outcome and more consolidated skills than massed practice and also resulted in a more consistent performance after three months of non-practice. Simulator-integrated tutoring accelerated the initial learning curve but also caused over-reliance on tutoring, which resulted in a drop in performance when the simulator-integrated tutor-function was discontinued. The learning curves were highly individual but often plateaued early and at an inadequate level, which related to issues concerning both the procedure and the VR simulator, over-reliance on the tutor function and poor self-assessment skills. Future simulator-integrated automated assessment could potentially resolve some of these issues and provide trainees with both feedback during the procedure and immediate

The McGill simulator for endoscopic sinus surgery (MSESS): a validation study.

Science.gov (United States)

Varshney, Rickul; Frenkiel, Saul; Nguyen, Lily H P; Young, Meredith; Del Maestro, Rolando; Zeitouni, Anthony; Saad, Elias; Funnell, W Robert J; Tewfik, Marc A

2014-10-24

Endoscopic sinus surgery (ESS) is a technically challenging procedure, associated with a significant risk of complications. Virtual reality simulation has demonstrated benefit in many disciplines as an important educational tool for surgical training. Within the field of rhinology, there is a lack of ESS simulators with appropriate validity evidence supporting their integration into residency education. The objectives of this study are to evaluate the acceptability, perceived realism and benefit of the McGill Simulator for Endoscopic Sinus Surgery (MSESS) among medical students, otolaryngology residents and faculty, and to present evidence supporting its ability to differentiate users based on their level of training through the performance metrics. 10 medical students, 10 junior residents, 10 senior residents and 3 expert sinus surgeons performed anterior ethmoidectomies, posterior ethmoidectomies and wide sphenoidotomies on the MSESS. Performance metrics related to quality (e.g. percentage of tissue removed), efficiency (e.g. time, path length, bimanual dexterity, etc.) and safety (e.g. contact with no-go zones, maximum applied force, etc.) were calculated. All users completed a post-simulation questionnaire related to realism, usefulness and perceived benefits of training on the MSESS. The MSESS was found to be realistic and useful for training surgical skills with scores of 7.97 ± 0.29 and 8.57 ± 0.69, respectively on a 10-point rating scale. Most students and residents (29/30) believed that it should be incorporated into their curriculum. There were significant differences between novice surgeons (10 medical students and 10 junior residents) and senior surgeons (10 senior residents and 3 sinus surgeons) in performance metrics related to quality (p education. This simulator may be a potential resource to help fill the void in endoscopic sinus surgery training.

Fact or factitious? A psychobiological study of authentic and simulated dissociative identity states.

Directory of Open Access Journals (Sweden)

A A T S Reinders

Full Text Available BACKGROUND: Dissociative identity disorder (DID is a disputed psychiatric disorder. Research findings and clinical observations suggest that DID involves an authentic mental disorder related to factors such as traumatization and disrupted attachment. A competing view indicates that DID is due to fantasy proneness, suggestibility, suggestion, and role-playing. Here we examine whether dissociative identity state-dependent psychobiological features in DID can be induced in high or low fantasy prone individuals by instructed and motivated role-playing, and suggestion. METHODOLOGY/PRINCIPAL FINDINGS: DID patients, high fantasy prone and low fantasy prone controls were studied in two different types of identity states (neutral and trauma-related in an autobiographical memory script-driven (neutral or trauma-related imagery paradigm. The controls were instructed to enact the two DID identity states. Twenty-nine subjects participated in the study: 11 patients with DID, 10 high fantasy prone DID simulating controls, and 8 low fantasy prone DID simulating controls. Autonomic and subjective reactions were obtained. Differences in psychophysiological and neural activation patterns were found between the DID patients and both high and low fantasy prone controls. That is, the identity states in DID were not convincingly enacted by DID simulating controls. Thus, important differences regarding regional cerebral bloodflow and psychophysiological responses for different types of identity states in patients with DID were upheld after controlling for DID simulation. CONCLUSIONS/SIGNIFICANCE: The findings are at odds with the idea that differences among different types of dissociative identity states in DID can be explained by high fantasy proneness, motivated role-enactment, and suggestion. They indicate that DID does not have a sociocultural (e.g., iatrogenic origin.

Fact or Factitious? A Psychobiological Study of Authentic and Simulated Dissociative Identity States

Science.gov (United States)

Simone Reinders, A. A. T.; Willemsen, Antoon T. M.; Vos, Herry P. J.; den Boer, Johan A.; Nijenhuis, Ellert R. S.

2012-01-01

Background Dissociative identity disorder (DID) is a disputed psychiatric disorder. Research findings and clinical observations suggest that DID involves an authentic mental disorder related to factors such as traumatization and disrupted attachment. A competing view indicates that DID is due to fantasy proneness, suggestibility, suggestion, and role-playing. Here we examine whether dissociative identity state-dependent psychobiological features in DID can be induced in high or low fantasy prone individuals by instructed and motivated role-playing, and suggestion. Methodology/Principal Findings DID patients, high fantasy prone and low fantasy prone controls were studied in two different types of identity states (neutral and trauma-related) in an autobiographical memory script-driven (neutral or trauma-related) imagery paradigm. The controls were instructed to enact the two DID identity states. Twenty-nine subjects participated in the study: 11 patients with DID, 10 high fantasy prone DID simulating controls, and 8 low fantasy prone DID simulating controls. Autonomic and subjective reactions were obtained. Differences in psychophysiological and neural activation patterns were found between the DID patients and both high and low fantasy prone controls. That is, the identity states in DID were not convincingly enacted by DID simulating controls. Thus, important differences regarding regional cerebral bloodflow and psychophysiological responses for different types of identity states in patients with DID were upheld after controlling for DID simulation. Conclusions/Significance The findings are at odds with the idea that differences among different types of dissociative identity states in DID can be explained by high fantasy proneness, motivated role-enactment, and suggestion. They indicate that DID does not have a sociocultural (e.g., iatrogenic) origin. PMID:22768068

Simulating clinical trial visits yields patient insights into study design and recruitment

Directory of Open Access Journals (Sweden)

Lim SS

2017-07-01

Full Text Available S Sam Lim,1 Alan J Kivitz,2 Doug McKinnell,3 M Edward Pierson,4 Faye S O’Brien4 1Division of Rheumatology, Department of Medicine, Emory University, Atlanta, GA, USA; 2Altoona Center for Clinical Research, Altoona, PA, USA; 3Deloitte Life Sciences Advisory, Basel, Switzerland; 4Clinical Operations, Global Medicines Development, AstraZeneca, Gaithersburg, MD, USA Purpose: We elicited patient experiences from clinical trial simulations to aid in future trial development and to improve patient recruitment and retention.Patients and methods: Two simulations of draft Phase II and Phase III anifrolumab studies for systemic lupus erythematosus (SLE/lupus nephritis (LN were performed involving African-American patients from Grady Hospital, an indigent care hospital in Atlanta, GA, USA, and white patients from Altoona Arthritis and Osteoporosis Center in Altoona, PA, USA. The clinical trial simulation included an informed consent procedure, a mock screening visit, a mock dosing visit, and a debriefing period for patients and staff. Patients and staff were interviewed to obtain sentiments and perceptions related to the simulated visits.Results: The Atlanta study involved 6 African-American patients (5 female aged 27–60 years with moderate to severe SLE/LN. The Altoona study involved 12 white females aged 32–75 years with mild to moderate SLE/LN. Patient experiences had an impact on four patient-centric care domains: 1 information, communication, and education; 2 responsiveness to needs; 3 access to care; and 4 coordination of care; and continuity and transition. Patients in both studies desired background material, knowledgeable staff, family and friend support, personal results, comfortable settings, shorter wait times, and greater scheduling flexibility. Compared with the Altoona study patients, Atlanta study patients reported greater preferences for information from the Internet, need for strong community and online support, difficulties in

A prospective study to determine the need for physical simulation following virtual simulation

International Nuclear Information System (INIS)

Valicenti, R.K.; Waterman, F.M.; Corn, B.W.; Sweet, J.; Curran, W.J.

1996-01-01

Purpose: Virtual simulation is CT based planning utilizing computed digitally reconstructed radiographs (DRRs) in a manner similar to conventional fluoroscopic simulation. However, conventional or physical simulation is still widely used to assure precise implementation of the devised plan. To evaluate the need for performing physical simulation, we prospectively studied patients undergoing virtual simulation who either had or did not have a subsequent physical simulation. Materials and Methods: From July, 1995 to February, 1996, 48 patients underwent conformal 4-field radiation therapy for prostate cancer using a commercial grade spiral CT simulator. All patients were immobilized in a foam body cast and positioned by using a fiducial laser marking system. Following prostate and seminal vesicle definition on a slice-by-slice basis, virtual simulation was performed. The isocenter defined by this process was marked on both the patient and the immobilization device before leaving the CT simulator room. The isocenter position of the devised plan was evaluated by three verification methods: physical simulation, first day treatment port filming, and port filming immediately following physical simulation. Simulator radiographs and port films were compared against DRRs for x, y, and z deviations of the isocenter. These deviations were used as a measure of the implementation precision achieved by each verification method. Results: Thirty-seven patients underwent physical simulation and first day port filming. Eleven had first day treatment verification films only and never had a physical simulation. A total of 79 simulator radiographs and 126 first day treatment port films were reviewed. The tabulation of all deviations is as follows: There was significantly more setup error (≥ 5 mm) observed when the devised treatment was implemented in the treatment room as opposed to the physical simulator. The physical simulator did not lead to a significant reduction in setup error

Head-on collisions of binary white dwarf-neutron stars: Simulations in full general relativity

International Nuclear Information System (INIS)

Paschalidis, Vasileios; Etienne, Zachariah; Liu, Yuk Tung; Shapiro, Stuart L.

2011-01-01

We simulate head-on collisions from rest at large separation of binary white dwarf-neutron stars (WDNSs) in full general relativity. Our study serves as a prelude to our analysis of the circular binary WDNS problem. We focus on compact binaries whose total mass exceeds the maximum mass that a cold-degenerate star can support, and our goal is to determine the fate of such systems. A fully general relativistic hydrodynamic computation of a realistic WDNS head-on collision is prohibitive due to the large range of dynamical time scales and length scales involved. For this reason, we construct an equation of state (EOS) which captures the main physical features of neutron stars (NSs) while, at the same time, scales down the size of white dwarfs (WDs). We call these scaled-down WD models 'pseudo-WDs (pWDs)'. Using pWDs, we can study these systems via a sequence of simulations where the size of the pWD gradually increases toward the realistic case. We perform two sets of simulations; One set studies the effects of the NS mass on the final outcome, when the pWD is kept fixed. The other set studies the effect of the pWD compaction on the final outcome, when the pWD mass and the NS are kept fixed. All simulations show that after the collision, 14%-18% of the initial total rest mass escapes to infinity. All remnant masses still exceed the maximum rest mass that our cold EOS can support (1.92M · ), but no case leads to prompt collapse to a black hole. This outcome arises because the final configurations are hot. All cases settle into spherical, quasiequilibrium configurations consisting of a cold NS core surrounded by a hot mantle, resembling Thorne-Zytkow objects. Extrapolating our results to realistic WD compactions, we predict that the likely outcome of a head-on collision of a realistic, massive WDNS system will be the formation of a quasiequilibrium Thorne-Zytkow-like object.

Revisiting the stellar velocity ellipsoid-Hubble-type relation: observations versus simulations

Science.gov (United States)

Pinna, F.; Falcón-Barroso, J.; Martig, M.; Martínez-Valpuesta, I.; Méndez-Abreu, J.; van de Ven, G.; Leaman, R.; Lyubenova, M.

2018-04-01

The stellar velocity ellipsoid (SVE) in galaxies can provide important information on the processes that participate in the dynamical heating of their disc components (e.g. giant molecular clouds, mergers, spiral density waves, and bars). Earlier findings suggested a strong relation between the shape of the disc SVE and Hubble type, with later-type galaxies displaying more anisotropic ellipsoids and early types being more isotropic. In this paper, we revisit the strength of this relation using an exhaustive compilation of observational results from the literature on this issue. We find no clear correlation between the shape of the disc SVE and morphological type, and show that galaxies with the same Hubble type display a wide range of vertical-to-radial velocity dispersion ratios. The points are distributed around a mean value and scatter of σz/σR = 0.7 ± 0.2. With the aid of numerical simulations, we argue that different mechanisms might influence the shape of the SVE in the same manner and that the same process (e.g. mergers) does not have the same impact in all the galaxies. The complexity of the observational picture is confirmed by these simulations, which suggest that the vertical-to-radial axis ratio of the SVE is not a good indicator of the main source of disc heating. Our analysis of those simulations also indicates that the observed shape of the disc SVE may be affected by several processes simultaneously and that the signatures of some of them (e.g. mergers) fade over time.

Axisymmetric core collapse simulations using characteristic numerical relativity

International Nuclear Information System (INIS)

Siebel, Florian; Mueller, Ewald; Font, Jose A.; Papadopoulos, Philippos

2003-01-01

We present results from nonrotating axisymmetric stellar core collapse simulations in general relativity. Our hydrodynamics code has proved robust and accurate enough to allow for a detailed analysis of the global dynamics of the collapse. Contrary to traditional approaches based on the 3+1 formulation of the gravitational field equations, our framework uses a foliation based on a family of outgoing light cones, emanating from a regular center, and terminating at future null infinity. Such a coordinate system is well adapted to the study of interesting dynamical spacetimes in relativistic astrophysics such as stellar core collapse and neutron star formation. Perhaps most importantly this procedure allows for the extraction of gravitational waves at future null infinity, along with the commonly used quadrupole formalism for the gravitational wave extraction. Our results concerning the gravitational wave signals show noticeable disagreement when those are extracted by computing the Bondi news at future null infinity on the one hand and by using the quadrupole formula on the other hand. We have a strong indication that for our setup the quadrupole formula on the null cone does not lead to physical gravitational wave signals. The Bondi gravitational wave signals extracted at infinity show typical oscillation frequencies of about 0.5 kHz

Study on the CFD simulation of refrigerated container

Science.gov (United States)

Arif Budiyanto, Muhammad; Shinoda, Takeshi; Nasruddin

2017-10-01

The objective this study is to performed Computational Fluid Dynamic (CFD) simulation of refrigerated container in the container port. Refrigerated container is a thermal cargo container constructed from an insulation wall to carry kind of perishable goods. CFD simulation was carried out use cross sectional of container walls to predict surface temperatures of refrigerated container and to estimate its cooling load. The simulation model is based on the solution of the partial differential equations governing the fluid flow and heat transfer processes. The physical model of heat-transfer processes considered in this simulation are consist of solar radiation from the sun, heat conduction on the container walls, heat convection on the container surfaces and thermal radiation among the solid surfaces. The validation of simulation model was assessed uses surface temperatures at center points on each container walls obtained from the measurement experimentation in the previous study. The results shows the surface temperatures of simulation model has good agreement with the measurement data on all container walls.

Direct Numerical Simulations of Dynamic Drainage and Imbibition to Investigate Capillary Pressure-Saturation-Interfacial Area Relation

Science.gov (United States)

Konangi, S.; Palakurthi, N. K.; Karadimitriou, N.; Comer, K.; Ghia, U.

2017-12-01

We present results of pore-scale direct numerical simulations (DNS) of drainage and imbibition in a quasi-two-dimensional (40µm thickness) porous medium with a randomly distributed packing of cylindrical obstructions. The Navier-Stokes (NS) equations are solved in the pore space on an Eulerian mesh using the open-source finite-volume computational fluid dynamics (CFD) code, OpenFOAM. The Volume-of-Fluid (VOF) method is employed to track the evolution of the fluid-fluid interface; a static contact angle is used to account for wall adhesion. From the DNS data, we focus on the macroscopic capillary pressure-saturation (Pc-Sw) relation, which is known to be hysteretic, i.e., this relation is flow process (such as drainage, imbibition and scanning curves) and history dependent. In order to overcome the problem of hysteresis, extended theories of multiphase flow hypothesized that the inclusion of specific interfacial area as a state variable will result in a unique relation between capillary pressure, saturation and interfacial area (Pc-Sw-awn). We study the role of specific interfacial area on hysteresis in the macroscopic Pc-Sw relation under non-equilibrium (dynamic) conditions. Under dynamic conditions, capillary pressure depends on the rate of change of the wetting phase saturation, and the dynamic Pc-Sw relation includes the changes caused by viscous effects. Simulations of drainage and imbibition are performed for two capillary numbers by controlling the flow rate of the non-wetting (polydimenthlysiloxane oil) and wetting (water) fluids. From these simulations, the Pc-Sw curves will be estimated; the Pc-S-awn surface will be constructed to determine whether the data points from drainage and imbibition processes fall on a unique surface under transient conditions. Different macroscopic capillary pressure definitions based on phase-averaged pressures and interfacial area will be evaluated. Understanding macroscopic capillary pressure definitions and the uniqueness

Python Open source Waveform ExtractoR (POWER): an open source, Python package to monitor and post-process numerical relativity simulations

Science.gov (United States)

Johnson, Daniel; Huerta, E. A.; Haas, Roland

2018-01-01

Numerical simulations of Einstein’s field equations provide unique insights into the physics of compact objects moving at relativistic speeds, and which are driven by strong gravitational interactions. Numerical relativity has played a key role to firmly establish gravitational wave astrophysics as a new field of research, and it is now paving the way to establish whether gravitational wave radiation emitted from compact binary mergers is accompanied by electromagnetic and astro-particle counterparts. As numerical relativity continues to blend in with routine gravitational wave data analyses to validate the discovery of gravitational wave events, it is essential to develop open source tools to streamline these studies. Motivated by our own experience as users and developers of the open source, community software, the Einstein Toolkit, we present an open source, Python package that is ideally suited to monitor and post-process the data products of numerical relativity simulations, and compute the gravitational wave strain at future null infinity in high performance environments. We showcase the application of this new package to post-process a large numerical relativity catalog and extract higher-order waveform modes from numerical relativity simulations of eccentric binary black hole mergers and neutron star mergers. This new software fills a critical void in the arsenal of tools provided by the Einstein Toolkit consortium to the numerical relativity community.

Student Perceptions of a Role-Playing Simulation in an Introductory International Relations Course

Science.gov (United States)

Giovanello, Sean P.; Kirk, Jason A.; Kromer, Mileah K.

2013-01-01

An emerging assumption in undergraduate political science education is that role-playing simulations are an effective teaching tool. While previous studies have addressed the pedagogical advantages of simulations as compared to more traditional teaching techniques, less attention has been paid to student perceptions of these simulations. This…

ALLAN.simulation club; Club ALLAN.simulation

Energy Technology Data Exchange (ETDEWEB)

Boudaud, F

1994-05-27

The ALLAN.Simulation code was developed by the R and D direction of Gaz de France (GdF) company with the support of CISI and Dassault Data Services companies. Its aim is to provide a modeling tool for the design and operation of complex technical systems. It uses a `boxes and ropes` representation (non-oriented multi-variable bloc-schemes) which allows the re-use of all or part of previous models or analyses already developed and recorded. The third meeting of the non-GdF users of the ALLAN.Simulation code took place at Sophia Antipolis (France) on May 27, 1994. Several studies performed with ALLAN.Simulation were presented and dealt with: a thermohydraulic loop, an alternator for automobile, and the hydration of cements. This report is a compilation of the transparencies relative to these three studies. A last part is devoted the presentation of the possible links between different existing simulation codes: ALLAN, BASILE, MAPLE, NEPTUNIX. (J.S.)

A numerical relativity scheme for cosmological simulations

Science.gov (United States)

Daverio, David; Dirian, Yves; Mitsou, Ermis

2017-12-01

Cosmological simulations involving the fully covariant gravitational dynamics may prove relevant in understanding relativistic/non-linear features and, therefore, in taking better advantage of the upcoming large scale structure survey data. We propose a new 3  +  1 integration scheme for general relativity in the case where the matter sector contains a minimally-coupled perfect fluid field. The original feature is that we completely eliminate the fluid components through the constraint equations, thus remaining with a set of unconstrained evolution equations for the rest of the fields. This procedure does not constrain the lapse function and shift vector, so it holds in arbitrary gauge and also works for arbitrary equation of state. An important advantage of this scheme is that it allows one to define and pass an adaptation of the robustness test to the cosmological context, at least in the case of pressureless perfect fluid matter, which is the relevant one for late-time cosmology.

Simulation studies for the evaluation of health information technologies

DEFF Research Database (Denmark)

Ammenwerth, Elske; Hackl, Werner; Binzer, Kristine

2012-01-01

It is essential for new health information technologies (IT) to undergo rigorous evaluations to ensure they are effective and safe for use in real-world situations. However, evaluation of new health IT is challenging, as field studies are often not feasible when the technology being evaluated...... is not sufficiently mature. Laboratory-based evaluations have also been shown to have insufficient external validity. Simulation studies seem to be a way to bridge this gap. The aim of this study was to evaluate, using a simulation methodology, the impact of a new prototype of an electronic medication management...... system on the appropriateness of prescriptions and drugrelated activities, including laboratory test ordering or medication changes. This article presents the results of a controlled simulation study with 50 simulation runs, including ten doctors and five simulation patients, and discusses experiences...

Digitalized design of extraforaminal lumbar interbody fusion: a computer-based simulation and cadaveric study.

Science.gov (United States)

Yang, Mingjie; Zeng, Cheng; Guo, Song; Pan, Jie; Han, Yingchao; Li, Zeqing; Li, Lijun; Tan, Jun

2014-01-01

This study aims to investigate the feasibility of a novel lumbar approach named extraforaminal lumbar interbody fusion (ELIF), a newly emerging minimally invasive technique for treating degenerative lumbar disorders, using a digitalized simulation and a cadaveric study. The ELIF surgical procedure was simulated using the Mimics surgical simulator and included dissection of the superior articular process, dilation of the vertebral foramen, and placement of pedicle screws and a cage. ELIF anatomical measures were documented using a digitalized technique and subsequently validated on fresh cadavers. The use of the Mimics allowed for the vivid simulation of ELIF surgical procedures, while the cadaveric study proved the feasibility of this novel approach. ELIF had a relatively lateral access approach that was located 8-9 cm lateral to the median line with an access depth of approximately 9 cm through the intermuscular space. Dissection of the superior articular processes could fully expose the target intervertebral discs and facilitate a more inclined placement of the pedicle screws and cage with robust enhancement. According to the computer-based simulation and cadaveric study, it is feasible to perform ELIF. Further research including biomechanical study is needed to prove ELIF has a superior ability to preserve the posterior tension bands of the spinal column, with similar effects on spinal decompression, fixation, and fusion, and if it can enhance post-fusion spinal stability and expedites postoperative recovery.

Studying pressure denaturation of a protein by molecular dynamics simulations.

Science.gov (United States)

Sarupria, Sapna; Ghosh, Tuhin; García, Angel E; Garde, Shekhar

2010-05-15

Many globular proteins unfold when subjected to several kilobars of hydrostatic pressure. This "unfolding-up-on-squeezing" is counter-intuitive in that one expects mechanical compression of proteins with increasing pressure. Molecular simulations have the potential to provide fundamental understanding of pressure effects on proteins. However, the slow kinetics of unfolding, especially at high pressures, eliminates the possibility of its direct observation by molecular dynamics (MD) simulations. Motivated by experimental results-that pressure denatured states are water-swollen, and theoretical results-that water transfer into hydrophobic contacts becomes favorable with increasing pressure, we employ a water insertion method to generate unfolded states of the protein Staphylococcal Nuclease (Snase). Structural characteristics of these unfolded states-their water-swollen nature, retention of secondary structure, and overall compactness-mimic those observed in experiments. Using conformations of folded and unfolded states, we calculate their partial molar volumes in MD simulations and estimate the pressure-dependent free energy of unfolding. The volume of unfolding of Snase is negative (approximately -60 mL/mol at 1 bar) and is relatively insensitive to pressure, leading to its unfolding in the pressure range of 1500-2000 bars. Interestingly, once the protein is sufficiently water swollen, the partial molar volume of the protein appears to be insensitive to further conformational expansion or unfolding. Specifically, water-swollen structures with relatively low radii of gyration have partial molar volume that are similar to that of significantly more unfolded states. We find that the compressibility change on unfolding is negligible, consistent with experiments. We also analyze hydration shell fluctuations to comment on the hydration contributions to protein compressibility. Our study demonstrates the utility of molecular simulations in estimating volumetric properties

Leading teams during simulated pediatric emergencies: a pilot study

Directory of Open Access Journals (Sweden)

Coolen EH

2015-01-01

Full Text Available Ester H Coolen,1 Jos M Draaisma,2 Sabien den Hamer,3 Jan L Loeffen2 1Department of Pediatric Surgery, Amalia Children’s Hospital, Radboud University Medical Center, 2Department of Pediatrics, Amalia Children’s Hospital, Radboud University Medical Center, 3Department of Communication Science, Radboud University, Nijmegen, the Netherlands Purpose: Leadership has been identified as a key variable for the functioning of teams and as one of the main reasons for success or failure of team-based work systems. Pediatricians often function as team leaders in the resuscitation of a critically ill child. However, pediatric residents often report having little opportunity to perform in the role of team leader during residency. In order to gain more insight into leadership skills and behaviors, we classified leadership styles of pediatric residents during simulated emergencies. Methods: We conducted a prospective quantitative study to investigate leadership styles used by pediatric residents during simulated emergencies with clinical deterioration of a child at a pediatric ward. Using videotaped scenarios of 48 simulated critical events among 12 residents, we were able to classify verbal and nonverbal communication into different leadership styles according to the situational leadership theory. Results: The coaching style (mean 54.5%, SD 7.8 is the most frequently applied by residents, followed by the directing style (mean 35.6%, SD 4.1. This pattern conforms to the task- and role-related requirements in our scenarios and it also conforms to the concept of situational leadership. We did not find any significant differences in leadership style according to the postgraduate year or scenario content. Conclusion: The model used in this pilot study helps us to gain a better understanding of the development of effective leadership behavior and supports the applicability of situational leadership theory in training leadership skills during residency. Keywords

Efficient algorithms for flow simulation related to nuclear reactor safety

International Nuclear Information System (INIS)

Gornak, Tatiana

2013-01-01

Safety analysis is of ultimate importance for operating Nuclear Power Plants (NPP). The overall modeling and simulation of physical and chemical processes occuring in the course of an accident is an interdisciplinary problem and has origins in fluid dynamics, numerical analysis, reactor technology and computer programming. The aim of the study is therefore to create the foundations of a multi-dimensional non-isothermal fluid model for a NPP containment and software tool based on it. The numerical simulations allow to analyze and predict the behavior of NPP systems under different working and accident conditions, and to develop proper action plans for minimizing the risks of accidents, and/or minimizing the consequences of possible accidents. A very large number of scenarios have to be simulated, and at the same time acceptable accuracy for the critical parameters, such as radioactive pollution, temperature, etc., have to be achieved. The existing software tools are either too slow, or not accurate enough. This thesis deals with developing customized algorithm and software tools for simulation of isothermal and non-isothermal flows in a containment pool of NPP. Requirements to such a software are formulated, and proper algorithms are presented. The goal of the work is to achieve a balance between accuracy and speed of calculation, and to develop customized algorithm for this special case. Different discretization and solution approaches are studied and those which correspond best to the formulated goal are selected, adjusted, and when possible, analysed. Fast directional splitting algorithm for Navier-Stokes equations in complicated geometries, in presence of solid and porous obstacles, is in the core of the algorithm. Developing suitable pre-processor and customized domain decomposition algorithms are essential part of the overall algorithm amd software. Results from numerical simulations in test geometries and in real geometries are presented and discussed.

Simulation study of the high intensity S-Band photoinjector

Energy Technology Data Exchange (ETDEWEB)

Zhu, Xiongwei; Nakajima, Kazuhisa [High Energy Accelerator Research Organization, Tsukuba, Ibaraki (Japan)

2001-10-01

In this paper, we report the results of simulation study of the high intensity S-Band photoinjector. The aim of the simulation study is to transport high bunch charge with low emittance evolution. The simulation result shows that 7nC bunch with rms emittance 22.3 {pi} mm mrad can be outputted at the exit of photoinjector. (author)

Simulation study of the high intensity S-Band photoinjector

International Nuclear Information System (INIS)

Zhu, Xiongwei; Nakajima, Kazuhisa

2001-01-01

In this paper, we report the results of simulation study of the high intensity S-Band photoinjector. The aim of the simulation study is to transport high bunch charge with low emittance evolution. The simulation result shows that 7nC bunch with rms emittance 22.3 π mm mrad can be outputted at the exit of photoinjector. (author)

When does alcohol hurt? A driving simulator study.

Science.gov (United States)

Vollrath, Mark; Fischer, Josefine

2017-12-01

World-wide, alcohol is still a major cause of traffic accidents. The dose-related accident risk function has been found in a large number of risk studies. A plethora of laboratory studies has examined the effect of alcohol with regard to different information processing capabilities of drivers. Summarizing the results, alcohol effects occur at lower blood alcohol concentrations (BAC) the more complex the tasks get. However, in contrast, typical alcohol-related crashes are frequently single vehicle crashes but not so often crashes in complex situations like at intersections. It may be that the subjective assessment of the traffic situation and the adaptation of behavior under the influence of alcohol plays a major role in accident causation. In order to examine this hypothesis, two driving simulator studies were conducted at a target BAC of 0.5g/l comparing two (alcohol vs. placebo; n=48, Experiment 1) and three (sober, placebo and alcohol; n=63, Experiment 2) groups of subjects in two critical scenarios. The first scenario was a seemingly easy traffic situation and was supposed to lead to a relaxed driving behavior under alcohol. The second scenario involved a complex intersection situation where especially drivers under the influence of alcohol should try to concentrate and compensate their experienced alcohol effects. In all scenarios, a critical object appeared suddenly and the driver had to react fast in order to prevent a (simulated) accident. Overall, the results support the hypothesis. Accidents were more frequent for alcohol drivers as compared to placebo/sober drivers in the easy scenario, but not the complex one. The initial speed of the driver when entering the scenario seems to play a major role in the accident causation. Drivers under the influence of alcohol seem to lower their speed in complex scenarios, possibly to thus counteract alcohol effects. In seemingly easy scenarios this does not seem necessary for them and the arousing effect of alcohol

Event-related potentials and secondary task performance during simulated driving.

Science.gov (United States)

Wester, A E; Böcker, K B E; Volkerts, E R; Verster, J C; Kenemans, J L

2008-01-01

Inattention and distraction account for a substantial number of traffic accidents. Therefore, we examined the impact of secondary task performance (an auditory oddball task) on a primary driving task (lane keeping). Twenty healthy participants performed two 20-min tests in the Divided Attention Steering Simulator (DASS). The visual secondary task of the DASS was replaced by an auditory oddball task to allow recording of brain activity. The driving task and the secondary (distracting) oddball task were presented in isolation and simultaneously, to assess their mutual interference. In addition to performance measures (lane keeping in the primary driving task and reaction speed in the secondary oddball task), brain activity, i.e. event-related potentials (ERPs), was recorded. Performance parameters on the driving test and the secondary oddball task did not differ between performance in isolation and simultaneous performance. However, when both tasks were performed simultaneously, reaction time variability increased in the secondary oddball task. Analysis of brain activity indicated that ERP amplitude (P3a amplitude) related to the secondary task, was significantly reduced when the task was performed simultaneously with the driving test. This study shows that when performing a simple secondary task during driving, performance of the driving task and this secondary task are both unaffected. However, analysis of brain activity shows reduced cortical processing of irrelevant, potentially distracting stimuli from the secondary task during driving.

Digitalized design of extraforaminal lumbar interbody fusion: a computer-based simulation and cadaveric study.

Directory of Open Access Journals (Sweden)

Mingjie Yang

Full Text Available PURPOSE: This study aims to investigate the feasibility of a novel lumbar approach named extraforaminal lumbar interbody fusion (ELIF, a newly emerging minimally invasive technique for treating degenerative lumbar disorders, using a digitalized simulation and a cadaveric study. METHODS: The ELIF surgical procedure was simulated using the Mimics surgical simulator and included dissection of the superior articular process, dilation of the vertebral foramen, and placement of pedicle screws and a cage. ELIF anatomical measures were documented using a digitalized technique and subsequently validated on fresh cadavers. RESULTS: The use of the Mimics allowed for the vivid simulation of ELIF surgical procedures, while the cadaveric study proved the feasibility of this novel approach. ELIF had a relatively lateral access approach that was located 8-9 cm lateral to the median line with an access depth of approximately 9 cm through the intermuscular space. Dissection of the superior articular processes could fully expose the target intervertebral discs and facilitate a more inclined placement of the pedicle screws and cage with robust enhancement. CONCLUSIONS: According to the computer-based simulation and cadaveric study, it is feasible to perform ELIF. Further research including biomechanical study is needed to prove ELIF has a superior ability to preserve the posterior tension bands of the spinal column, with similar effects on spinal decompression, fixation, and fusion, and if it can enhance post-fusion spinal stability and expedites postoperative recovery.

IgG4-related disease simulating Hodgkin lymphoma in a child

Directory of Open Access Journals (Sweden)

D. Eric Ewing, MD

2016-06-01

Full Text Available Immunoglobulin (Ig G4-related disease is a recently described syndrome characterized by mass forming lymphoplasmacytic tissue infiltration and elevated serum IgG4 concentrations usually affecting middle-aged or older individuals. Lymphadenopathy is frequently observed and is sometimes the first or only manifestation of the disease. We report a case of IgG4-related disease mimicking Hodgkin lymphoma in a 13-year-old girl. The patient presented with progressive unilateral cervical lymphadenopathy of several months duration. Biopsy showed follicular hyperplasia with progressive transformation of germinal centers. Interfollicular areas were expanded by small lymphocytes, histiocytes, eosinophils and fibrosis with occasional CD30 positive cells initially concerning for interfollicular Hodgkin lymphoma. Immunohistochemical analysis revealed an intrafollicular plasmacytosis with an IgG4-positive/IgG-positive plasma cell ratio of 50% supporting a diagnosis of IgG4-related lymphadenopathy, progressively transformed germinal centers type. Laboratory studies were supportive with elevated serum IgG4 (178 mg/dL and IgE (30.40 kU/L levels along with an elevated serum IgG4/IgG ratio (0.16. Very few cases of IgG4-related disease have been described in children. Within this age group, there is considerable clinical overlap between IgG4-related disease associated lymphadenopathy and Hodgkin lymphoma. In addition, lymphadenopathy secondary to IgG4-related disease demonstrates substantial histologic diversity with the potential to simulate the inflammatory background and fibrosis of Hodgkin lymphoma. The importance of accurate diagnosis is underscored by the prognostic implications considering the marked response of the syndrome to steroid therapy. In addition, appropriate follow up is critical to monitor for relapse and additional organ involvement.

Leading teams during simulated pediatric emergencies: a pilot study

Science.gov (United States)

Coolen, Ester H; Draaisma, Jos M; den Hamer, Sabien; Loeffen, Jan L

2015-01-01

Purpose Leadership has been identified as a key variable for the functioning of teams and as one of the main reasons for success or failure of team-based work systems. Pediatricians often function as team leaders in the resuscitation of a critically ill child. However, pediatric residents often report having little opportunity to perform in the role of team leader during residency. In order to gain more insight into leadership skills and behaviors, we classified leadership styles of pediatric residents during simulated emergencies. Methods We conducted a prospective quantitative study to investigate leadership styles used by pediatric residents during simulated emergencies with clinical deterioration of a child at a pediatric ward. Using videotaped scenarios of 48 simulated critical events among 12 residents, we were able to classify verbal and nonverbal communication into different leadership styles according to the situational leadership theory. Results The coaching style (mean 54.5%, SD 7.8) is the most frequently applied by residents, followed by the directing style (mean 35.6%, SD 4.1). This pattern conforms to the task- and role-related requirements in our scenarios and it also conforms to the concept of situational leadership. We did not find any significant differences in leadership style according to the postgraduate year or scenario content. Conclusion The model used in this pilot study helps us to gain a better understanding of the development of effective leadership behavior and supports the applicability of situational leadership theory in training leadership skills during residency. PMID:25610010

Combining annual daylight simulation with photobiology data to assess the relative circadian efficacy of interior spaces

Energy Technology Data Exchange (ETDEWEB)

Pechacek, C.S.; Andersen, M. [Massachusetts Inst. of Technology, Cambridge, MA (United States). Dept. of Architecture, Building Technology; Lockley, S.W. [Harvard Medical School, Boston, MA (United States). Div. of Sleep Medicine, Brigham and Women' s Hospital

2008-07-01

This paper addressed the issue of hospital design and the role of daylight in patient health care. It presented a new approach for integrating empirical data and findings in photobiology into the performance assessment of a space, thus combining both visual and health-related criteria. Previous studies have reported significant health care outcomes in daylit environments, although the mechanism and photoreceptor systems controlling these effects remain unknown. This study focused on furthering the previous studies beyond windows to describing the characteristics of daylight that may promote human health by providing daylighting for the appropriate synchronization of circadian rhythms, and then make specific daylighting recommendations, grounded in biological findings. In particular, this study investigated the use of daylight autonomy (DA) to simulate the probabilistic and temporal potential of daylight for human health needs. Results of photobiology research were used to define threshold values for lighting, which were then used as goals for simulations. These goals included spectrum, intensity and timing of light at the human eye. The study investigated the variability of key architectural decisions in hospital room design to determine their influence on achieving the goals. The simulations showed how choices in building orientation, window size, user-window position and interior finishes affect the circadian efficacy of a space. Design decisions can improve or degrade the health potential for the space considered. While the findings in this research were specific to hospitals, the results can be applied to other building types such as office buildings and residences. 33 refs., 7 figs.

Special relativity in beam trajectory simulation in small accelerators

International Nuclear Information System (INIS)

Pramudita Anggraita; Budi Santosa; Taufik; Emy Mulyani; Frida Iswinning Diah

2012-01-01

Calculation for trajectory simulation of particle beam in small accelerators should account special relativity effect in the beam motion, which differs between parallel and perpendicular direction to the beam velocity. For small electron beam machine of 300 keV, the effect shows up as the rest mass of electron is only 511 keV. Neglecting the effect yields wrong kinetic energy after 300 kV of dc acceleration. For a 13 MeV PET (positron emission tomography) baby cyclotron accelerating proton beam, the effect increases the proton mass by about 1.4% at the final energy. To keep the beam isochronous with the accelerating radiofrequency, a radial increase of the average magnetic field must be designed accordingly. (author)

Simulation and experimental study on distortion of butt and T-joints using WELD PLANNER

International Nuclear Information System (INIS)

Sulaiman, Mohd Shahar; Manurung, Yupiter HP; Rahim, Mohammad Ridzwan Abdul Mohd; Redza, Ridhwan; Lidam, Robert Ngendang Ak.; Abas, Sunhaji Kiyai; Tham, Ghalib; Haruman, Esa; Chau, Chan Yin

2011-01-01

This paper investigates the capability of linear thermal elastic numerical analysis to predict the welding distortion that occurs due to GMAW process. Distortion is considered as the major stumbling block that can adversely affect the dimensional accuracy and thus lead to expensive corrective work. Hence, forecast of distortion is crucially needed and ought to be determined in advance in order to minimize the negative effects, improve the quality of welded parts and finally to reduce the production costs. In this study, the welding deformation was simulated by using relatively new FEM software WELD PLANNER developed by ESI Group. This novel Welding Simulation Solution was employed to predict welding distortion induced in butt and T-joints with thickness of 4 mm. Low carbon steel material was used for the simulation and experimental study. A series of experiments using fully automated welding process were conducted for verification purpose to measure the distortion. By comparing between the simulation and experimental results, it was found out that this program code offered fast solution analysis time in estimating weld induced distortion within acceptable accuracy

Simulation and experimental study on distortion of butt and T-joints using WELD PLANNER

Energy Technology Data Exchange (ETDEWEB)

Sulaiman, Mohd Shahar; Manurung, Yupiter HP; Rahim, Mohammad Ridzwan Abdul Mohd; Redza, Ridhwan; Lidam, Robert Ngendang Ak.; Abas, Sunhaji Kiyai; Tham, Ghalib [Universiti Teknologi MARA, Kuala Lumpur (Malaysia); Haruman, Esa [Bakrie University, Jakarta (Indonesia); Chau, Chan Yin [ESI Group, Kuala Lumpur (Malaysia)

2011-10-15

This paper investigates the capability of linear thermal elastic numerical analysis to predict the welding distortion that occurs due to GMAW process. Distortion is considered as the major stumbling block that can adversely affect the dimensional accuracy and thus lead to expensive corrective work. Hence, forecast of distortion is crucially needed and ought to be determined in advance in order to minimize the negative effects, improve the quality of welded parts and finally to reduce the production costs. In this study, the welding deformation was simulated by using relatively new FEM software WELD PLANNER developed by ESI Group. This novel Welding Simulation Solution was employed to predict welding distortion induced in butt and T-joints with thickness of 4 mm. Low carbon steel material was used for the simulation and experimental study. A series of experiments using fully automated welding process were conducted for verification purpose to measure the distortion. By comparing between the simulation and experimental results, it was found out that this program code offered fast solution analysis time in estimating weld induced distortion within acceptable accuracy.

Study of plasticity in metals by numerical simulations

International Nuclear Information System (INIS)

Clouet, E.

2013-01-01

We present a study of the plastic behaviour in metals based on the modelling of dislocation properties. Different simulation tools have been used and developed to study plasticity in structural materials, in particular metals used in the nuclear industry. In iron or zirconium alloys, plasticity is controlled at low temperature by the glide of screw dislocations. Atomistic simulations can be used to model dislocation core properties and thus to obtain a better knowledge of the mechanisms controlling dislocation glide. Such atomistic simulations need nevertheless some special care because of the long range elastic field induced by the dislocations. We have therefore developed a modelling approach relying both on atomistic simulations, using either empirical interatomic potentials or ab initio calculations, and on elasticity theory. Such an approach has been used to obtain dislocation intrinsic core properties. These simulations allowed us to describe, in iron, the variations of these core properties with the dislocation character. In zirconium, we could identity the origin of the high lattice friction and obtain a better understanding of the competition between the different glide systems. At high temperature, dislocations do not only glide but can also cross-slip or climb. This leads to a motion of the dislocations out of their glide plane which needs to be considered when modelling the plastic flow. We performed a study of dislocation climb at different scales, leading to the implementation of a dislocation climb model in dislocation dynamics simulations. (author) [fr

A comparative study on real lab and simulation lab in communication engineering from students' perspectives

Science.gov (United States)

Balakrishnan, B.; Woods, P. C.

2013-05-01

Over the years, rapid development in computer technology has engendered simulation-based laboratory (lab) in addition to the traditional hands-on (physical) lab. Many higher education institutions adopt simulation lab, replacing some existing physical lab experiments. The creation of new systems for conducting engineering lab activities has raised concerns among educators on the merits and shortcomings of both physical and simulation labs; at the same time, many arguments have been raised on the differences of both labs. Investigating the effectiveness of both labs is complicated, as there are multiple factors that should be considered. In view of this challenge, a study on students' perspectives on their experience related to key aspects on engineering laboratory exercise was conducted. In this study, the Visual Auditory Read and Kinetic model was utilised to measure the students' cognitive styles. The investigation was done through a survey among participants from Multimedia University, Malaysia. The findings revealed that there are significant differences for most of the aspects in physical and simulation labs.

Simulating Shopper Behavior using Fuzzy Logic in Shopping Center Simulation

Directory of Open Access Journals (Sweden)

Jason Christian

2016-12-01

Full Text Available To simulate real-world phenomena, a computer tool can be used to run a simulation and provide a detailed report. By using a computer-aided simulation tool, we can retrieve information relevant to the simulated subject in a relatively short time. This study is an extended and complete version of an initial research done by Christian and Hansun and presents a prototype of a multi-agent shopping center simulation tool along with a fuzzy logic algorithm implemented in the system. Shopping centers and all their components are represented in a simulated 3D environment. The simulation tool was created using the Unity3D engine to build the 3D environment and to run the simulation. To model and simulate the behavior of agents inside the simulation, a fuzzy logic algorithm that uses the agents’ basic knowledge as input was built to determine the agents’ behavior inside the system and to simulate human behaviors as realistically as possible.

Simulation Optimization by Genetic Search: A Comprehensive Study with Applications to Production Management

National Research Council Canada - National Science Library

Yunker, James

2003-01-01

In this report, a relatively new simulation optimization technique, the genetic search, is compared to two more established simulation techniques-the pattern search and the response surface methodology search...

Superheating of Ag nanowires studied by molecular dynamics simulations

International Nuclear Information System (INIS)

Duan Wenshi; Ling Guangkong; Hong Lin; Li Hong; Liang Minghe

2008-01-01

The melting process of Ag nanowires was studied by molecular dynamics (MD) simulations at the atomic level. It is indicated that the Ag nanowires with Ni coating can be superheated depending on their radius and size. Also, in this paper the mechanism of superheating was analyzed and ascribed to the epitaxial Ag/Ni interface suppressing the nucleation and growth of melt. For the analysis, a thermodynamic model was constructed to describe the superheating mechanism of the Ni-coated Ag nanowires by considering the Ag/Ni interface free energy. We showed that the nucleation and growth of the Ag melt phase are both suppressed by the low energy Ag/Ni interfaces in Ni-coated Ag wires and the suppression of melt growth is crucial and plays a major role in the process of melting. The thermodynamic analysis gave a quantitative relation of superheating with the Ag wire radius and the contact angle of melting. The superheating decreased with Ag wire radius and also depended on the Ag/Ni interfacial condition. The results of the thermodynamic model were consistent with those of the MD simulations

Foraging efficiency of a predator flock for randomly moving prey: A simulation study

Science.gov (United States)

Lee, Sang-Hee; Kwon, Ohsung

2016-03-01

Flocking behavior of animals is highly advantageous for taking food resources. The degree of the advantage is related to the ability of flock members to detect their prey and the mobility of prey individuals. In this study, to explore the relation, we constructed a model to simulate a predator flock and its randomly moving prey. The predator members have the prey detection ability, which was characterized as sensing distance, R, and a sensing angle, θ. The mobility of the prey individuals was characterized as the maximum traveling distance of an iteration time step, L. The relative flock foraging efficiency, ɛ, was defined as ɛ = 1 - (Td/Tup). Tup and Td represent the spent time for the flock to eat all prey individuals and to uptake the last remaining 10% prey, respectively. Simulation results showed that ɛ increased, maximized, and decreased with the increase of R, regardless of L. As the number of prey, N, increased, the tendency of the increasing and decreasing was diluted. The result was briefly discussed in relation to the flock foraging behavior and the development of the model toward applications for real ecosystems.

Study and simulation of human interface; Human interface kenkyu to simulation

Energy Technology Data Exchange (ETDEWEB)

Nishitani, H. [Nara Institute of Science and Technology, Nara (Japan)

1996-10-05

Validation researches have begun about the interrelationship between systems and human beings using a virtual-reality plant environment. This article introduces some recent studies about the human interface in an operation control system in a virtual-reality environment. The evaluation of a system from the viewpoint of ease of use is called a usability test, to which a psychological protocol analysis is applied for finding out problematic points by carefully observing the operator actually operating the system. For instance, in a boiler plant simulator constructed for DCS training, the operator is given some tasks, such as the prediction as to how a certain event will develop, probing of the cause of anomalies, and execution of related operations. Video cameras are installed at various spots for the minute observation of facial expressions and behavior of the operator, and the operator`s recognition, thought, behavior, and utterances, expressed by the operator facially or verbally, are recorded and analyzed, and the results are utilized for system improvement and operator training. 3 refs., 2 figs.

Learning with a strategic management simulation game: A case study

OpenAIRE

Loon, Mark; Evans, Jason; Kerridge, Clive

2015-01-01

The use of simulation games as a pedagogic method is well established though its effective use is context-driven. This study adds to the increasing growing body of empirical evidence of the effectiveness of simulation games but more importantly emphasises why by explaining the instructional design implemented reflecting best practices. This multi-method study finds evidence that student learning was enhanced through the use of simulation games, reflected in the two key themes; simulation game...

Driving Simulator Development and Performance Study

OpenAIRE

Juto, Erik

2010-01-01

The driving simulator is a vital tool for much of the research performed at theSwedish National Road and Transport Institute (VTI). Currently VTI posses three driving simulators, two high fidelity simulators developed and constructed by VTI, and a medium fidelity simulator from the German company Dr.-Ing. Reiner Foerst GmbH. The two high fidelity simulators run the same simulation software, developed at VTI. The medium fidelity simulator runs a proprietary simulation software. At VTI there is...

Multi-Bunch Simulations of the ILC for Luminosity Performance Studies

CERN Document Server

White, Glen; Walker, Nicholas J

2005-01-01

To study the luminosity performance of the International Linear Collider (ILC) with different design parameters, a simulation was constructed that tracks a multi-bunch representation of the beam from the Damping Ring extraction through to the Interaction Point. The simulation code PLACET is used to simulate the LINAC, MatMerlin is used to track through the Beam Delivery System and GUINEA-PIG for the beam-beam interaction. Included in the simulation are ground motion and wakefield effects, intra-train fast feedback and luminosity-based feedback systems. To efficiently study multiple parameters/multiple seeds, the simulation is deployed on the Queen Mary High-Throughput computing cluster at Queen Mary, University of London, where 100 simultaneous simulation seeds can be run.

A molecular dynamics simulation study of chloroform

Science.gov (United States)

Tironi, Ilario G.; van Gunsteren, Wilfred F.

Three different chloroform models have been investigated using molecular dynamics computer simulation. The thermodynamic, structural and dynamic properties of the various models were investigated in detail. In particular, the potential energies, diffusion coefficients and rotational correlation times obtained for each model are compared with experiment. It is found that the theory of rotational Brownian motion fails in describing the rotational diffusion of chloroform. The force field of Dietz and Heinzinger was found to give good overall agreement with experiment. An extended investigation of this chloroform model has been performed. Values are reported for the isothermal compressibility, the thermal expansion coefficient and the constant volume heat capacity. The values agree well with experiment. The static and frequency dependent dielectric permittivity were computed from a 1·2 ns simulation conducted under reaction field boundary conditions. Considering the fact that the model is rigid with fixed partial charges, the static dielectric constant and Debye relaxation time compare well with experiment. From the same simulation the shear viscosity was computed using the off-diagonal elements of the pressure tensor, both via an Einstein type relation and via a Green-Kubo equation. The calculated viscosities show good agreement with experimental values. The excess Helmholtz energy is calculated using the thermodynamic integration technique and simulations of 50 and 80 ps. The value obtained for the excess Helmholtz energy matches the theoretical value within a few per cent.

Partnering to Establish and Study Simulation in International Nursing Education.

Science.gov (United States)

Garner, Shelby L; Killingsworth, Erin; Raj, Leena

The purpose of this article was to describe an international partnership to establish and study simulation in India. A pilot study was performed to determine interrater reliability among faculty new to simulation when evaluating nursing student competency performance. Interrater reliability was below the ideal agreement level. Findings in this study underscore the need to obtain baseline interrater reliability data before integrating competency evaluation into a simulation program.

PEPT: An invaluable tool for 3-D particle tracking and CFD simulation verification in hydrocyclone studies

Directory of Open Access Journals (Sweden)

Hoffmann Alex C.

2013-05-01

Full Text Available Particle tracks in a hydrocyclone generated both experimentally by positron emission particle tracking (PEPT and numerically with Eulerian-Lagranian CFD have been studied and compared. A hydrocyclone with a cylinder-on-cone design was used in this study, the geometries used in the CFD simulations and in the experiments being identical. It is shown that it is possible to track a fast-moving particle in a hydrocyclone using PEPT with high temporal and spatial resolutions. The numerical 3-D particle trajectories were generated using the Large Eddy Simulation (LES turbulence model for the fluid and Lagrangian particle tracking for the particles. The behaviors of the particles were analyzed in detail and were found to be consistent between experiments and CFD simulations. The tracks of the particles are discussed and related to the fluid flow field visualized in the CFD simulations using the cross-sectional static pressure distribution.

An Integrated Capillary, Buoyancy, and Viscous-Driven Model for Brine/CO2Relative Permeability in a Compositional and Parallel Reservoir Simulator

KAUST Repository

Kong, X.; Delshad, M.; Wheeler, M. F.

2012-01-01

The effectiveness of CO2 storage in the saline aquifers is governed by the interplay of capillary, viscous, and buoyancy forces. Recent experimental study reveals the impact of pressure, temperature, and salinity on interfacial tension (IFT) between CO2 and brine. The dependence of CO2-brine relative permeability and capillary pressure on pressure (IFT) is also clearly evident in published experimental results. Improved understanding of the mechanisms that control the migration and trapping of CO2 in subsurface is crucial to design future storage projects that warrant long-term and safe containment. Simulation studies ignoring the buoyancy and also variation in interfacial tension and the effect on the petrophysical properties such as trapped CO2 saturations, relative permeability, and capillary pressure have a poor chance of making accurate predictions of CO2 injectivity and plume migration. We have developed and implemented a general relative permeability model that combines effects of pressure gradient, buoyancy, and IFT in an equation of state (EOS) compositional and parallel simulator. The significance of IFT variations on CO2 migration and trapping is assessed.

An Integrated Capillary, Buoyancy, and Viscous-Driven Model for Brine/CO2Relative Permeability in a Compositional and Parallel Reservoir Simulator

KAUST Repository

Kong, X.

2012-11-03

The effectiveness of CO2 storage in the saline aquifers is governed by the interplay of capillary, viscous, and buoyancy forces. Recent experimental study reveals the impact of pressure, temperature, and salinity on interfacial tension (IFT) between CO2 and brine. The dependence of CO2-brine relative permeability and capillary pressure on pressure (IFT) is also clearly evident in published experimental results. Improved understanding of the mechanisms that control the migration and trapping of CO2 in subsurface is crucial to design future storage projects that warrant long-term and safe containment. Simulation studies ignoring the buoyancy and also variation in interfacial tension and the effect on the petrophysical properties such as trapped CO2 saturations, relative permeability, and capillary pressure have a poor chance of making accurate predictions of CO2 injectivity and plume migration. We have developed and implemented a general relative permeability model that combines effects of pressure gradient, buoyancy, and IFT in an equation of state (EOS) compositional and parallel simulator. The significance of IFT variations on CO2 migration and trapping is assessed.

In-hospital resuscitation evaluated by in situ simulation: a prospective simulation study

DEFF Research Database (Denmark)

Mondrup, Frederik; Brabrand, Mikkel; Folkestad, Lars

2011-01-01

, and to examine differences in the resuscitation performance between the first responders and the cardiac arrest team. METHOD: S: A prospective observational study of 16 unannounced simulated cardiopulmonary arrest scenarios was conducted. The participants of the study involved all health care personel on duty...

Simulation studies for a high resolution time projection chamber at the international linear collider

Energy Technology Data Exchange (ETDEWEB)

Muennich, A.

2007-03-26

The International Linear Collider (ILC) is planned to be the next large accelerator. The ILC will be able to perform high precision measurements only possible at the clean environment of electron positron collisions. In order to reach this high accuracy, the requirements for the detector performance are challenging. Several detector concepts are currently under study. The understanding of the detector and its performance will be crucial to extract the desired physics results from the data. To optimise the detector design, simulation studies are needed. Simulation packages like GEANT4 allow to model the detector geometry and simulate the energy deposit in the different materials. However, the detector response taking into account the transportation of the produced charge to the readout devices and the effects ofthe readout electronics cannot be described in detail. These processes in the detector will change the measured position of the energy deposit relative to the point of origin. The determination of this detector response is the task of detailed simulation studies, which have to be carried out for each subdetector. A high resolution Time Projection Chamber (TPC) with gas amplification based on micro pattern gas detectors, is one of the options for the main tracking system at the ILC. In the present thesis a detailed simulation tool to study the performance of a TPC was developed. Its goal is to find the optimal settings to reach an excellent momentum and spatial resolution. After an introduction to the present status of particle physics and the ILC project with special focus on the TPC as central tracker, the simulation framework is presented. The basic simulation methods and implemented processes are introduced. Within this stand-alone simulation framework each electron produced by primary ionisation is transferred through the gas volume and amplified using Gas Electron Multipliers (GEMs). The output format of the simulation is identical to the raw data from a

Large-scale introduction of wind power stations in the Swedish grid: a simulation study

Energy Technology Data Exchange (ETDEWEB)

Larsson, L

1978-08-01

This report describes a simulation study on the factors to be considered if wind power were to be introduced to the south Swedish power grid on a large scale. The simulations are based upon a heuristic power generation planning model, developed for the purpose. The heuristic technique reflects the actual running strategies of a big power company with suitable accuracy. All simulations refer to certain typical days in 1976 to which all wind data and system characteristics are related. The installed amount of wind power will not be subject to optimization. All differences between planned and real wind power generation is equalized by regulation of the hydro power. The simulations made differ according to how the installed amount of wind power is handled in the power generation planning. The simulations indicate that the power system examined could well bear an introduction of wind power up to a level of 20% of the total power installed. This result is of course valid only for the days examined and does not necessarily apply to the present day structure of the system.

Female song rates in response to simulated intruder are positively related to reproductive success.

Directory of Open Access Journals (Sweden)

Kristal E Cain

2015-10-01

Full Text Available Bird song is well studied in males as a sexually selected behavior. However, although song is also common among females, it is infrequently examined and poorly understood. Research suggests that song is often used as a resource defense behavior and is important in female-female competition for limited resources, e.g. mates and territories. If so, song should be positively related to fitness and related to other resource defense behaviors, but this possibility has rarely been explored. Here we examine fitness estimates in relation to spontaneous song rates and song rates in response to a simulated intruder (playback, in the superb fairy-wren (Malurus cyaneus, a cooperatively breeding songbird. We also determine how song rates relate to other territorial defense behaviors. Song rate in response to playback, but not spontaneous song rate, was positively related to nest success and the number of fledglings produced by successful females. Further, response song rate was also correlated with other territorial defense behaviors (latency to respond and flights. This evidence supports the hypothesis that female song may be used in the context of female-female competition to improve access to limited reproductive resources, and suggests that song may provide direct fitness benefits.

BC404 scintillators as gamma locators studied via Geant4 simulations

Science.gov (United States)

Cortés, M. L.; Hoischen, R.; Eisenhauer, K.; Gerl, J.; Pietralla, N.

2014-05-01

In many applications in industry and academia, an accurate determination of the direction from where gamma rays are emitted is either needed or desirable. Ion-beam therapy treatments, the search for orphan sources, and homeland security applications are examples of fields that can benefit from directional sensitivity to gamma-radiation. Scintillation detectors are a good option for these types of applications as they have relatively low cost, are easy to handle and can be produced in a large range of different sizes. In this work a Geant4 simulation was developed to study the directional sensitivity of different BC404 scintillator geometries and arrangements. The simulation includes all the physical processes relevant for gamma detection in a scintillator. In particular, the creation and propagation of optical photons inside the scintillator was included. A simplified photomultiplier tube model was also simulated. The physical principle exploited is the angular dependence of the shape of the energy spectrum obtained from thin scintillator layers when irradiated from different angles. After an experimental confirmation of the working principle of the device and a check of the simulation, the possibilities and limitations of directional sensitivity to gamma radiation using scintillator layers was tested. For this purpose, point-like sources of typical energies expected in ion-beam therapy were used. Optimal scintillator thicknesses for different energies were determined and the setup efficiencies calculated. The use of arrays of scintillators to reconstruct the direction of incoming gamma rays was also studied. For this case, a spherical source emitting Bremsstrahlung radiation was used together with a setup consisting of scintillator layers. The capability of this setup to identify the center of the extended source was studied together with its angular resolution.

Lung assist devices influence cardio-energetic parameters: Numerical simulation study.

Science.gov (United States)

De Lazzari, C; Quatember, B; Recheis, W; Mayr, M; Demertzis, S; Allasia, G; De Rossi, A; Cavoretto, R; Venturino, E; Genuini, I

2015-08-01

We aim at an analysis of the effects mechanical ventilators (MVs) and thoracic artificial lungs (TALs) will have on the cardiovascular system, especially on important quantities, such as left and right ventricular external work (EW), pressure-volume area (PVA) and cardiac mechanical efficiency (CME). Our analyses are based on simulation studies which were carried out by using our CARDIOSIM(©) software simulator. At first, we carried out simulation studies of patients undergoing mechanical ventilation (MV) without a thoracic artificial lung (TAL). Subsequently, we conducted simulation studies of patients who had been provided with a TAL, but did not undergo MV. We aimed at describing the patient's physiological characteristics and their variations with time, such as EW, PVA, CME, cardiac output (CO) and mean pulmonary arterial/venous pressure (PAP/PVP). We were starting with a simulation run under well-defined initial conditions which was followed by simulation runs for a wide range of mean intrathoracic pressure settings. Our simulations of MV without TAL showed that for mean intrathoracic pressure settings from negative (-4 mmHg) to positive (+5 mmHg) values, the left and right ventricular EW and PVA, right ventricular CME and CO decreased, whereas left ventricular CME and the PAP increased. The simulation studies of patients with a TAL, comprised all the usual TAL arrangements, viz. configurations "in series" and in parallel with the natural lung and, moreover, hybrid configurations. The main objective of the simulation studies was, as before, the assessment of the hemodynamic response to the application of a TAL. We could for instance show that, in case of an "in series" configuration, a reduction (an increase) in left (right) ventricular EW and PVA values occurred, whereas the best performance in terms of CO can be achieved in the case of an in parallel configuration.

Studies on the survival of Ascaris suum eggs under laboratory and simulated field conditions

NARCIS (Netherlands)

Gaasenbeek, C.P.H.; Borgsteede, F.H.M.

1998-01-01

A series of four experiments was carried out to study the survival of Ascaris suum eggs: in a pig slurry unit on a farm, in the laboratory under anaerobic conditions and different relative humidities (rH), and under simulated field conditions. Survival of eggs in the pig slurry unit was 20% after

Human factors in resuscitation: Lessons learned from simulator studies

Directory of Open Access Journals (Sweden)

Hunziker S

2010-01-01

Full Text Available Medical algorithms, technical skills, and repeated training are the classical cornerstones for successful cardiopulmonary resuscitation (CPR. Increasing evidence suggests that human factors, including team interaction, communication, and leadership, also influence the performance of CPR. Guidelines, however, do not yet include these human factors, partly because of the difficulties of their measurement in real-life cardiac arrest. Recently, clinical studies of cardiac arrest scenarios with high-fidelity video-assisted simulations have provided opportunities to better delineate the influence of human factors on resuscitation team performance. This review focuses on evidence from simulator studies that focus on human factors and their influence on the performance of resuscitation teams. Similar to studies in real patients, simulated cardiac arrest scenarios revealed many unnecessary interruptions of CPR as well as significant delays in defibrillation. These studies also showed that human factors play a major role in these shortcomings and that the medical performance depends on the quality of leadership and team-structuring. Moreover, simulated video-taped medical emergencies revealed that a substantial part of information transfer during communication is erroneous. Understanding the impact of human factors on the performance of a complex medical intervention like resuscitation requires detailed, second-by-second, analysis of factors involving the patient, resuscitative equipment such as the defibrillator, and all team members. Thus, high-fidelity simulator studies provide an important research method in this challenging field.

Diagnostic budget study of the internal variability in ensemble simulations of the Canadian RCM

Energy Technology Data Exchange (ETDEWEB)

Nikiema, Oumarou; Laprise, Rene [UQAM, Canadian Network for Regional Climate Modelling and Diagnostics, Centre ESCER, Departement des Sciences de la Terre et de l' Atmosphere, B.P. 8888, Montreal, QC (Canada)

2011-06-15

Due to the chaotic and nonlinear nature of the atmospheric dynamics, it is known that small differences in the initial conditions (IC) of models can grow and affect the simulation evolution. In this study, we perform a quantitative diagnostic budget calculation of the various diabatic and dynamical contributions to the time evolution and spatial distribution of internal variability (IV) in simulations with the nested Canadian Regional Climate Model. We establish prognostic budget equations of the IV for the potential temperature and the relative vorticity fields. For both of these variables, the IV equations present similar terms, notably terms relating to the transport of IV by ensemble-mean flow and to the covariance of fluctuations acting on the gradient of the ensemble-mean state. We show the skill of these equations to diagnose the IV that took place in an ensemble of 20 3-month (summer season) simulations that differed only in their IC. Our study suggests that the dominant terms responsible for the large increase of IV are either the covariance term involving the potential temperature fluctuations and diabatic heating fluctuations, or the covariance of inter-member fluctuations acting upon ensemble-mean gradients. Our results also show that, on average, the third-order terms are negligible, but they can become important when the IV is large. (orig.)

A simulated regolith medium for multi-wavelength studies

Science.gov (United States)

Wilkman, O.; Muinonen, K.; Parviainen, H.; Näränen, J.

2012-04-01

Effects arising from the small-scale surface structure are significant in remote studies of regolith surfaces on atmosphereless solar system bodies, such as the Moon, Mercury and the asteroids. The important properties determining these effects are the porosity of the regolith and the roughness of the interface between the bulk material and empty space. We concentrate on the regolith effects in visible light photometry and X-ray spectrometry. The fluorescent X-ray spectrum induced by solar X-rays contains information about the elemental abundances of the surface material, while the photometry can be used to constrain surface properties such as porosity. We have developed a computer model simulating a regolith medium consisting of spherical particles with variable size distribution and properties. The bulk properties of the medium, such as porosity and surface roughness, can be varied. The model can then be used in ray-tracing simulations of the regolith effects in both visible light scattering and X-ray fluorescence. In photometric studies the scattering law of the constituent particles can be chosen to take into account scattering phenomena such as coherent backscattering. In the X-ray simulations, we can choose the elemental abundances of the material and the spectrum of the incident X-ray radiation. The ray-tracing simulations then allow us to determine the characteristics of the emitted radiation in different observational geometries. We present results from various studies which have been based on our regolith model. The model has been used to simulate the regolith effects on X-ray fluorescence spectra under specific situations. These can be compared to laboratory measurements. The visible light simulations have been applied in a study of the shadowing effects in photometry. The model was also used in a study of lunar photometry from SMART-1/AMIE data. Applications in the analysis of X-ray spectrometry from the BepiColombo MIXS/SIXS instruments are planned. An

Laparoscopic skills acquisition: a study of simulation and traditional training.

Science.gov (United States)

Marlow, Nicholas; Altree, Meryl; Babidge, Wendy; Field, John; Hewett, Peter; Maddern, Guy J

2014-12-01

Training in basic laparoscopic skills can be undertaken using traditional methods, where trainees are educated by experienced surgeons through a process of graduated responsibility or by simulation-based training. This study aimed to assess whether simulation trained individuals reach the same level of proficiency in basic laparoscopic skills as traditional trained participants when assessed in a simulated environment. A prospective study was undertaken. Participants were allocated to one of two cohorts according to surgical experience. Participants from the inexperienced cohort were randomized to receive training in basic laparoscopic skills on either a box trainer or a virtual reality simulator. They were then assessed on the simulator on which they did not receive training. Participants from the experienced cohort, considered to have received traditional training in basic laparoscopic skills, did not receive simulation training and were randomized to either the box trainer or virtual reality simulator for skills assessment. The assessment scores from different cohorts on either simulator were then compared. A total of 138 participants completed the assessment session, 101 in the inexperienced simulation-trained cohort and 37 on the experienced traditionally trained cohort. There was no statistically significant difference between the training outcomes of simulation and traditionally trained participants, irrespective of the simulator type used. The results demonstrated that participants trained on either a box trainer or virtual reality simulator achieved a level of basic laparoscopic skills assessed in a simulated environment that was not significantly different from participants who had been traditionally trained in basic laparoscopic skills. © 2013 Royal Australasian College of Surgeons.

The process of adopting and incorporating simulation into undergraduate nursing curricula: a grounded theory study.

Science.gov (United States)

Taplay, Karyn; Jack, Susan M; Baxter, Pamela; Eva, Kevin; Martin, Lynn

2015-01-01

The aim of this study is to explain the process of adopting and incorporating simulation as a teaching strategy in undergraduate nursing programs, define uptake, and discuss potential outcomes. In many countries, simulation is increasingly adopted as a common teaching strategy. However, there is a dearth of knowledge related to the process of adoption and incorporation. We used an interpretive, constructivist approach to grounded theory to guide this research study. We conducted the study was in Ontario, Canada, during 2011-2012. Using multiple data sources, we informed the development of this theory including in-depth interviews (n = 43) and a review of key organizational documents, such as mission and vision statements (n = 67) from multiple nursing programs (n = 13). The adoption and uptake of mid- to high-fidelity simulation equipment is a multistep iterative process involving various organizational levels within the institution that entails a seven-phase process: (a) securing resources, (b) nursing leaders working in tandem, (c) getting it out of the box, (d) learning about simulation and its potential for teaching, (e) finding a fit, (f) trialing the equipment, and (g) integrating into the curriculum. These findings could assist nursing programs in Canada and internationally that wish to adopt or further incorporate simulation into their curricula and highlight potential organizational and program level outcomes. Crown Copyright © 2015. Published by Elsevier Inc. All rights reserved.

Simulation of merging neutron stars in full general relativity

International Nuclear Information System (INIS)

Shibata, M.

2001-01-01

We have performed 3D numerical simulations for merger of equal mass binary neutron stars in full general relativity. We adopt a Γ-law equation of state in the form P = (Γ - 1)ρε where P, ρ, ε and Γ are the pressure, rest mass density, specific internal energy, and the adiabatic constant. As initial conditions, we adopt models of irrotational binary neutron stars in a quasiequilibrium state. Simulations have been carried out for a wide range of Γ and compactness of neutron stars, paying particular attention to the final product and gravitational waves. We find that the final product depends sensitively on the initial compactness of the neutron stars: In a merger between sufficiently compact neutron stars, a black hole is formed in a dynamical timescale. As the compactness is decreased, the formation timescale becomes longer and longer. It is also found that a differentially rotating massive neutron star is formed instead of a black hole for less compact binary cases. In the case of black hole formation, the disk mass around the black hole appears to be very small; less than 1% of the total rest mass. It is indicated that waveforms of high-frequency gravitational waves after merger depend strongly on the compactness of neutron stars before the merger. We point out importance of detecting such gravitational waves of high frequency to constrain the maximum allowed mass of neutron stars. (author)

A simulation study provided sample size guidance for differential item functioning (DIF) studies using short scales

DEFF Research Database (Denmark)

Scott, Neil W.; Fayers, Peter M.; Bottomley, Andrew

2009-01-01

Differential item functioning (DIF) analyses are increasingly used to evaluate health-related quality of life (HRQoL) instruments, which often include relatively short subscales. Computer simulations were used to explore how various factors including scale length affect analysis of DIF by ordinal...... logistic regression....

Scale issues in soil hydrology related to measurement and simulation: A case study in Colorado

Science.gov (United States)

State variables, such as soil water content (SWC), are typically measured or inferred at very small scales while being simulated at larger scales relevant to spatial management or hillslope areas. Thus there is an implicit spatial disparity that is often ignored. Surface runoff, on the other hand, ...

Comparison of robustness to outliers between robust poisson models and log-binomial models when estimating relative risks for common binary outcomes: a simulation study.

Science.gov (United States)

Chen, Wansu; Shi, Jiaxiao; Qian, Lei; Azen, Stanley P

2014-06-26

To estimate relative risks or risk ratios for common binary outcomes, the most popular model-based methods are the robust (also known as modified) Poisson and the log-binomial regression. Of the two methods, it is believed that the log-binomial regression yields more efficient estimators because it is maximum likelihood based, while the robust Poisson model may be less affected by outliers. Evidence to support the robustness of robust Poisson models in comparison with log-binomial models is very limited. In this study a simulation was conducted to evaluate the performance of the two methods in several scenarios where outliers existed. The findings indicate that for data coming from a population where the relationship between the outcome and the covariate was in a simple form (e.g. log-linear), the two models yielded comparable biases and mean square errors. However, if the true relationship contained a higher order term, the robust Poisson models consistently outperformed the log-binomial models even when the level of contamination is low. The robust Poisson models are more robust (or less sensitive) to outliers compared to the log-binomial models when estimating relative risks or risk ratios for common binary outcomes. Users should be aware of the limitations when choosing appropriate models to estimate relative risks or risk ratios.

The Simulation Study of Horizontal Axis Water Turbine Using Flow Simulation Solidworks Application

Science.gov (United States)

Prasetyo, H.; Budiana, EP; Tjahjana, DDDP; Hadi, S.

2018-02-01

The design of Horizontal Axis Water Turbine in pico hydro power plants involves many parameters. To simplify that, usually using computer simulation is applied. This research performs simulation process variation on turbine blade number, turbine blade curvature angle, turbine bucket angle and blocking system tilt angle. Those four variations were combined in order to obtain the best design of turbine. The study used Flow Simulation Solidworks application, and obtain data on turbine speed, pressure, force, and torque. However, this research focused on turbine torque value. The best design of turbine was obtained in the turbine with 6 blades, blade curvature angle of 65° and bucket angle of 10°, and blocking system tilt angle of 40°. In the best turbine, the produced torque value was 8.464 Nm.

Designing a Qualitative Data Collection Strategy (QDCS) for Africa - Phase 1: A Gap Analysis of Existing Models, Simulations, and Tools Relating to Africa

Science.gov (United States)

2012-06-01

QDCS) for Africa – Phase I: A Gap Analysis of Existing Models, Simulations, and Tools Relating to Africa Ashley N. Bybee , Project Leader Dominick E...Strategy (QDCS) for Africa – Phase I: A Gap Analysis of Existing Models, Simulations, and Tools Relating to Africa Ashley N. Bybee , Project Leader...Africa Phase I: A Gap Analysis of Existing Models, Simulations, and Tools Relating to Africa June 2012 Authors: Dr. Ashley Bybee , Project Lead Dr

Spatial variations in estimated chronic exposure to traffic-related air pollution in working populations: A simulation

Directory of Open Access Journals (Sweden)

Cloutier-Fisher Denise

2008-07-01

Full Text Available Abstract Background Chronic exposure to traffic-related air pollution is associated with a variety of health impacts in adults and recent studies show that exposure varies spatially, with some residents in a community more exposed than others. A spatial exposure simulation model (SESM which incorporates six microenvironments (home indoor, work indoor, other indoor, outdoor, in-vehicle to work and in-vehicle other is described and used to explore spatial variability in estimates of exposure to traffic-related nitrogen dioxide (not including indoor sources for working people. The study models spatial variability in estimated exposure aggregated at the census tracts level for 382 census tracts in the Greater Vancouver Regional District of British Columbia, Canada. Summary statistics relating to the distributions of the estimated exposures are compared visually through mapping. Observed variations are explored through analyses of model inputs. Results Two sources of spatial variability in exposure to traffic-related nitrogen dioxide were identified. Median estimates of total exposure ranged from 8 μg/m3 to 35 μg/m3 of annual average hourly NO2 for workers in different census tracts in the study area. Exposure estimates are highest where ambient pollution levels are highest. This reflects the regional gradient of pollution in the study area and the relatively high percentage of time spent at home locations. However, for workers within the same census tract, variations were observed in the partial exposure estimates associated with time spent outside the residential census tract. Simulation modeling shows that some workers may have exposures 1.3 times higher than other workers residing in the same census tract because of time spent away from the residential census tract, and that time spent in work census tracts contributes most to the differences in exposure. Exposure estimates associated with the activity of commuting by vehicle to work were

Communication: Minimum in the thermal conductivity of supercooled water: A computer simulation study

Energy Technology Data Exchange (ETDEWEB)

Bresme, F., E-mail: f.bresme@imperial.ac.uk [Chemical Physics Section, Department of Chemistry, Imperial College, London SW7 2AZ, United Kingdom and Department of Chemistry, Norwegian University of Science and Technology, Trondheim 7491 (Norway); Biddle, J. W.; Sengers, J. V.; Anisimov, M. A. [Institute for Physical Science and Technology, and Department of Chemical and Biomolecular Engineering, University of Maryland, College Park, Maryland 20742 (United States)

2014-04-28

We report the results of a computer simulation study of the thermodynamic properties and the thermal conductivity of supercooled water as a function of pressure and temperature using the TIP4P-2005 water model. The thermodynamic properties can be represented by a two-structure equation of state consistent with the presence of a liquid-liquid critical point in the supercooled region. Our simulations confirm the presence of a minimum in the thermal conductivity, not only at atmospheric pressure, as previously found for the TIP5P water model, but also at elevated pressures. This anomalous behavior of the thermal conductivity of supercooled water appears to be related to the maximum of the isothermal compressibility or the minimum of the speed of sound. However, the magnitudes of the simulated thermal conductivities are sensitive to the water model adopted and appear to be significantly larger than the experimental thermal conductivities of real water at low temperatures.

Communication: Minimum in the thermal conductivity of supercooled water: A computer simulation study

International Nuclear Information System (INIS)

Bresme, F.; Biddle, J. W.; Sengers, J. V.; Anisimov, M. A.

2014-01-01

We report the results of a computer simulation study of the thermodynamic properties and the thermal conductivity of supercooled water as a function of pressure and temperature using the TIP4P-2005 water model. The thermodynamic properties can be represented by a two-structure equation of state consistent with the presence of a liquid-liquid critical point in the supercooled region. Our simulations confirm the presence of a minimum in the thermal conductivity, not only at atmospheric pressure, as previously found for the TIP5P water model, but also at elevated pressures. This anomalous behavior of the thermal conductivity of supercooled water appears to be related to the maximum of the isothermal compressibility or the minimum of the speed of sound. However, the magnitudes of the simulated thermal conductivities are sensitive to the water model adopted and appear to be significantly larger than the experimental thermal conductivities of real water at low temperatures

Simulator Evaluation of Drivers’ Performance on Rural Highways in relation to Drivers’ Visual Attention Demands

Directory of Open Access Journals (Sweden)

Yaqin Qin

2015-01-01

Full Text Available Aim of the study is to investigate, by means of a driving simulator experiment, drivers’ performance in terms of lateral position, speed, deceleration, steering angle, and breaking times on a divided two-lane rural highway in relation to drivers’ visual attention (VD. In the experiment, the virtual scene of twenty different geometric alignment sections without traffic and the VD testing were designed. Twenty-three experienced drivers with the calibration of attention capacity participated in a 30 km drive in an interactive fixed-base simulator. Each participant was required to drive with the controlled speed of 60 km/h along the central lane as repeating random number and was evaluated on VD and driving performances. Three different data analysis techniques were used: (a statistical tests and hypothesis test of curvature change rate (CCR of the geometric alignments, visual attention demands, and driving performance data, (b correlation analysis of VD, CCRs, and driving behaviors, and (c regression analysis of the VD and CCRs. Results have showed that the driving performance can be effectively influenced by the highway alignment and a prediction model built in this study can evaluate the drivers’ visual attention demands before the highway constructed. The interactions among VD, driving behavior, and CCRs were also found.

Study on a computerized compact simulator of NHR-200

International Nuclear Information System (INIS)

Gao Zuying; Dong Yujie

1997-01-01

A fully computerized compact simulator is studied in accordance with the engineering practical need of NHR-200. A SUN SPARC 2 stand-alone workstation is selected as its computer system and multi-task structure of software is employed. Simulation program is derived from the RETRAN-02 code. The standard I/O devices are used as its interface equipment and the man-machine interface graphic program is coded on the basis of X Window System. Shared memory and semaphores are used for inter-task communication and a timer is used in real-time control of tasks. Its accuracy and simulation speed are verified by using several typical accident transients. The accuracy and speed are perfectly able to meet the requirements of engineering simulation. It is useful for normal and accident transient analysis, engineering study and design, reactor operation support and personnel training

Predictive validity of driving-simulator assessments following traumatic brain injury: a preliminary study.

Science.gov (United States)

Lew, Henry L; Poole, John H; Lee, Eun Ha; Jaffe, David L; Huang, Hsiu-Chen; Brodd, Edward

2005-03-01

To evaluate whether driving simulator and road test evaluations can predict long-term driving performance, we conducted a prospective study on 11 patients with moderate to severe traumatic brain injury. Sixteen healthy subjects were also tested to provide normative values on the simulator at baseline. At their initial evaluation (time-1), subjects' driving skills were measured during a 30-minute simulator trial using an automated 12-measure Simulator Performance Index (SPI), while a trained observer also rated their performance using a Driving Performance Inventory (DPI). In addition, patients were evaluated on the road by a certified driving evaluator. Ten months later (time-2), family members observed patients driving for at least 3 hours over 4 weeks and rated their driving performance using the DPI. At time-1, patients were significantly impaired on automated SPI measures of driving skill, including: speed and steering control, accidents, and vigilance to a divided-attention task. These simulator indices significantly predicted the following aspects of observed driving performance at time-2: handling of automobile controls, regulation of vehicle speed and direction, higher-order judgment and self-control, as well as a trend-level association with car accidents. Automated measures of simulator skill (SPI) were more sensitive and accurate than observational measures of simulator skill (DPI) in predicting actual driving performance. To our surprise, the road test results at time-1 showed no significant relation to driving performance at time-2. Simulator-based assessment of patients with brain injuries can provide ecologically valid measures that, in some cases, may be more sensitive than a traditional road test as predictors of long-term driving performance in the community.

Simulation study on cross polarization scattering of ultrashort-pulse electromagnetic waves

International Nuclear Information System (INIS)

Katsuragawa, Naoki; Hojo, Hitoshi; Mase, Atushi

1996-11-01

Simulation study on cross polarization scattering of ultrashort-pulse electromagnetic waves due to magnetic fluctuations is presented. One-dimensional coupled wave equations for the ordinary and extraordinary modes are solved for incident unipolar sub-cycle pulses in an inhomogeneous magnetized plasma. It is shown that the peak frequencies in the frequency-spectral signals of the mode-converted reflected waves are determined from the Bragg resonance condition in the wave numbers of the ordinary mode, the extraordinary mode and the magnetic fluctuations for relatively short-wavelength localized magnetic fluctuations. (author)

Baccalaureate nursing students' perspectives of peer tutoring in simulation laboratory, a Q methodology study.

Science.gov (United States)

Li, Ting; Petrini, Marcia A; Stone, Teresa E

2018-02-01

The study aim was to identify the perceived perspectives of baccalaureate nursing students toward the peer tutoring in the simulation laboratory. Insight into the nursing students' experiences and baseline data related to their perception of peer tutoring will assist to improve nursing education. Q methodology was applied to explore the students' perspectives of peer tutoring in the simulation laboratory. A convenience P-sample of 40 baccalaureate nursing students was used. Fifty-eight selected Q statements from each participant were classified into the shape of a normal distribution using an 11-point bipolar scale form with a range from -5 to +5. PQ Method software analyzed the collected data. Three discrete factors emerged: Factor I ("Facilitate or empower" knowledge acquisition), Factor II ("Safety Net" Support environment), and Factor III ("Mentoring" learn how to learn). The findings of this study support and indicate that peer tutoring is an effective supplementary strategy to promote baccalaureate students' knowledge acquisition, establishing a supportive safety net and facilitating their abilities to learn in the simulation laboratory. Copyright © 2017 Elsevier Ltd. All rights reserved.

A Parametric Study on Welding Process Simulation for Multi-pass welds in a Plate

Energy Technology Data Exchange (ETDEWEB)

Park, Won Dong; Bahn, Chi Bum; Kim, Ji Hun [Pusan National University, Busan (Korea, Republic of)

2016-05-15

EPRI (MRP-316, 317) (1,2) and USNRC (NUREG-2162)(3) have performed related studies for FEA models to predict the weld residual stress distribution. In this work, a systematic parametric study was performed to find out how major assumptions and conditions used in the simulation could affect the weld residual stress distribution. 2- dimensional simulation was conducted by using commercial FEA software, ABAQUS(4) , for multi-pass Alloy 82 welds performed in a stainless steel plate (EPRI MRP-316, P-4, phase 1). From the previous results, we could make the following conclusions. 1. The method of applying power density is more realistic than predefined temperature. 2. It seems that annealing effect reduces the transverse direction weld residual stress (S33). However more detailed analyses for annealing effect are needed.

Nitrogen-Related Constraints of Carbon Uptake by Large-Scale Forest Expansion: Simulation Study for Climate Change and Management Scenarios

Science.gov (United States)

Kracher, Daniela

2017-11-01

Increase of forest areas has the potential to increase the terrestrial carbon (C) sink. However, the efficiency for C sequestration depends on the availability of nutrients such as nitrogen (N), which is affected by climatic conditions and management practices. In this study, I analyze how N limitation affects C sequestration of afforestation and how it is influenced by individual climate variables, increased harvest, and fertilizer application. To this end, JSBACH, the land component of the Earth system model of the Max Planck Institute for Meteorology is applied in idealized simulation experiments. In those simulations, large-scale afforestation increases the terrestrial C sink in the 21st century by around 100 Pg C compared to a business as usual land-use scenario. N limitation reduces C sequestration roughly by the same amount. The relevance of compensating effects of uptake and release of carbon dioxide by plant productivity and soil decomposition, respectively, gets obvious from the simulations. N limitation of both fluxes compensates particularly in the tropics. Increased mineralization under global warming triggers forest expansion, which otherwise is restricted by N availability. Due to compensating higher plant productivity and soil respiration, the global net effect of warming for C sequestration is however rather small. Fertilizer application and increased harvest enhance C sequestration as well as boreal expansion. The additional C sequestration achieved by fertilizer application is offset to a large part by additional emissions of nitrous oxide.

Seventeenth Workshop on Computer Simulation Studies in Condensed-Matter Physics

CERN Document Server

Landau, David P; Schütler, Heinz-Bernd; Computer Simulation Studies in Condensed-Matter Physics XVI

2006-01-01

This status report features the most recent developments in the field, spanning a wide range of topical areas in the computer simulation of condensed matter/materials physics. Both established and new topics are included, ranging from the statistical mechanics of classical magnetic spin models to electronic structure calculations, quantum simulations, and simulations of soft condensed matter. The book presents new physical results as well as novel methods of simulation and data analysis. Highlights of this volume include various aspects of non-equilibrium statistical mechanics, studies of properties of real materials using both classical model simulations and electronic structure calculations, and the use of computer simulations in teaching.

Development of a Cardiovascular Simulator for Studying Pulse Diagnosis Mechanisms

Directory of Open Access Journals (Sweden)

Min Jang

2017-01-01

Full Text Available This research was undertaken to develop a cardiovascular simulator for use in the study of pulse diagnosis. The physical (i.e., pulse wave transmission and reflection and physiological (i.e., systolic and diastolic pressure, pulse pressure, and mean pressure characteristics of the radial pulse wave were reproduced by our simulator. The simulator consisted of an arterial component and a pulse-generating component. Computer simulation was used to simplify the arterial component while maintaining the elastic modulus and artery size. To improve the reflected wave characteristics, a palmar arch was incorporated within the simulator. The simulated radial pulse showed good agreement with clinical data.

A Study on Data Base for the Pyroprocessing Material Flow and MUF Uncertainty Simulation

International Nuclear Information System (INIS)

Sitompul, Yos Panagaman; Shin, Heesung; Han, Boyoung; Kim, Hodong

2011-01-01

The data base for the pyroprocessing material flow and MUF uncertainty simulation has been implemented well. There is no error in the data base processing and it is relatively fast by using OLEDB and MySQL. The important issue is the data base size. In OLEDB the data base size is limited to 2 Gb. To reduce the data base size, we give an option for users to filter the input nuclides based on their masses and activities. A simulation program called PYMUS has been developed to study the pyroprocessing material flow and MUF. In the program, there is a data base system that controls the data processing in the simulation. The data base system consists of input data base, data processing, and output data base. The data base system has been designed in such a way to be efficient. One example is using the OLEDB and MySQL. The data base system is explained in detail in this paper. The result shows that the data base system works well in the simulation

Relative Free Energies for Hydration of Monovalent Ions from QM and QM/MM Simulations.

Science.gov (United States)

Lev, Bogdan; Roux, Benoît; Noskov, Sergei Yu

2013-09-10

Methods directly evaluating the hydration structure and thermodynamics of physiologically relevant cations (Na(+), K(+), Cl(-), etc.) have wide ranging applications in the fields of inorganic, physical, and biological chemistry. All-atom simulations based on accurate potential energy surfaces appear to offer a viable option for assessing the chemistry of ion solvation. Although MD and free energy simulations of ion solvation with classical force fields have proven their usefulness, a number of challenges still remain. One of them is the difficulty of force field benchmarking and validation against structural and thermodynamic data obtained for a condensed phase. Hybrid quantum mechanical/molecular mechanical (QM/MM) models combined with sampling algorithms have the potential to provide an accurate solvation model and to incorporate the effects from the surrounding, which is often missing in gas-phase ab initio computations. Herein, we report the results from QM/MM free energy simulations of Na(+)/K(+) and Cl(-)/Br(-) hydration where we simultaneously characterized the relative thermodynamics of ion solvation and changes in the solvation structure. The Flexible Inner Region Ensemble Separator (FIRES) method was used to impose a spatial separation between QM region and the outer sphere of solvent molecules treated with the CHARMM27 force field. FEP calculations based on QM/MM simulations utilizing the CHARMM/deMon2k interface were performed with different basis set combinations for K(+)/Na(+) and Cl(-)/Br(-) perturbations to establish the dependence of the computed free energies on the basis set level. The dependence of the computed relative free energies on the size of the QM and MM regions is discussed. The current methodology offers an accurate description of structural and thermodynamic aspects of the hydration of alkali and halide ions in neat solvents and can be used to obtain thermodynamic data on ion solvation in condensed phase along with underlying

DWPF simulant CPC studies for SB8

Energy Technology Data Exchange (ETDEWEB)

Koopman, D. C.; Zamecnik, J. R.

2013-06-25

The Savannah River National Laboratory (SRNL) accepted a technical task request (TTR) from Waste Solidification Engineering to perform simulant tests to support the qualification of Sludge Batch 8 (SB8) and to develop the flowsheet for SB8 in the Defense Waste Processing Facility (DWPF). These efforts pertained to the DWPF Chemical Process Cell (CPC). Separate studies were conducted for frit development and glass properties (including REDOX). The SRNL CPC effort had two primary phases divided by the decision to drop Tank 12 from the SB8 constituents. This report focuses on the second phase with SB8 compositions that do not contain the Tank 12 piece. A separate report will document the initial phase of SB8 testing that included Tank 12. The second phase of SB8 studies consisted of two sets of CPC studies. The first study involved CPC testing of an SB8 simulant for Tank 51 to support the CPC demonstration of the washed Tank 51 qualification sample in the SRNL Shielded Cells facility. SB8-Tank 51 was a high iron-low aluminum waste with fairly high mercury and moderate noble metal concentrations. Tank 51 was ultimately washed to about 1.5 M sodium which is the highest wash endpoint since SB3-Tank 51. This study included three simulations of the DWPF Sludge Receipt and Adjustment Tank (SRAT) cycle and Slurry Mix Evaporator (SME) cycle with the sludge-only flowsheet at nominal DWPF processing conditions and three different acid stoichiometries. These runs produced a set of recommendations that were used to guide the successful SRNL qualification SRAT/SME demonstration with actual Tank 51 washed waste. The second study involved five SRAT/SME runs with SB8-Tank 40 simulant. Four of the runs were designed to define the acid requirements for sludge-only processing in DWPF with respect to nitrite destruction and hydrogen generation. The fifth run was an intermediate acid stoichiometry demonstration of the coupled flowsheet for SB8. These runs produced a set of processing

DWPF simulant CPC studies for SB8

International Nuclear Information System (INIS)

Koopman, D. C.; Zamecnik, J. R.

2013-01-01

The Savannah River National Laboratory (SRNL) accepted a technical task request (TTR) from Waste Solidification Engineering to perform simulant tests to support the qualification of Sludge Batch 8 (SB8) and to develop the flowsheet for SB8 in the Defense Waste Processing Facility (DWPF). These efforts pertained to the DWPF Chemical Process Cell (CPC). Separate studies were conducted for frit development and glass properties (including REDOX). The SRNL CPC effort had two primary phases divided by the decision to drop Tank 12 from the SB8 constituents. This report focuses on the second phase with SB8 compositions that do not contain the Tank 12 piece. A separate report will document the initial phase of SB8 testing that included Tank 12. The second phase of SB8 studies consisted of two sets of CPC studies. The first study involved CPC testing of an SB8 simulant for Tank 51 to support the CPC demonstration of the washed Tank 51 qualification sample in the SRNL Shielded Cells facility. SB8-Tank 51 was a high iron-low aluminum waste with fairly high mercury and moderate noble metal concentrations. Tank 51 was ultimately washed to about 1.5 M sodium which is the highest wash endpoint since SB3-Tank 51. This study included three simulations of the DWPF Sludge Receipt and Adjustment Tank (SRAT) cycle and Slurry Mix Evaporator (SME) cycle with the sludge-only flowsheet at nominal DWPF processing conditions and three different acid stoichiometries. These runs produced a set of recommendations that were used to guide the successful SRNL qualification SRAT/SME demonstration with actual Tank 51 washed waste. The second study involved five SRAT/SME runs with SB8-Tank 40 simulant. Four of the runs were designed to define the acid requirements for sludge-only processing in DWPF with respect to nitrite destruction and hydrogen generation. The fifth run was an intermediate acid stoichiometry demonstration of the coupled flowsheet for SB8. These runs produced a set of processing

Virtual gaming simulation of a mental health assessment: A usability study.

Science.gov (United States)

Verkuyl, Margaret; Romaniuk, Daria; Mastrilli, Paula

2018-05-18

Providing safe and realistic virtual simulations could be an effective way to facilitate the transition from the classroom to clinical practice. As nursing programs begin to include virtual simulations as a learning strategy; it is critical to first assess the technology for ease of use and usefulness. A virtual gaming simulation was developed, and a usability study was conducted to assess its ease of use and usefulness for students and faculty. The Technology Acceptance Model provided the framework for the study, which included expert review and testing by nursing faculty and nursing students. This study highlighted the importance of assessing ease of use and usefulness in a virtual game simulation and provided feedback for the development of an effective virtual gaming simulation. The study participants said the virtual gaming simulation was engaging, realistic and similar to a clinical experience. Participants found the game easy to use and useful. Testing provided the development team with ideas to improve the user interface. The usability methodology provided is a replicable approach to testing virtual experiences before a research study or before implementing virtual experiences into curriculum. Copyright © 2018 Elsevier Ltd. All rights reserved.

Experiment-scale molecular simulation study of liquid crystal thin films

Science.gov (United States)

Nguyen, Trung Dac; Carrillo, Jan-Michael Y.; Matheson, Michael A.; Brown, W. Michael

2014-03-01

Supercomputers have now reached a performance level adequate for studying thin films with molecular detail at the relevant scales. By exploiting the power of GPU accelerators on Titan, we have been able to perform simulations of characteristic liquid crystal films that provide remarkable qualitative agreement with experimental images. We have demonstrated that key features of spinodal instability can only be observed with sufficiently large system sizes, which were not accessible with previous simulation studies. Our study emphasizes the capability and significance of petascale simulations in providing molecular-level insights in thin film systems as well as other interfacial phenomena.

Data on simulated interpersonal touch, individual differences and the error-related negativity

Directory of Open Access Journals (Sweden)

Mandy Tjew-A-Sin

2016-06-01

Full Text Available The dataset includes data from the electroencephalogram study reported in our paper: ‘Effects of simulated interpersonal touch and trait intrinsic motivation on the error-related negativity’ (doi:10.1016/j.neulet.2016.01.044 (Tjew-A-Sin et al., 2016 [1]. The data was collected at the psychology laboratories at the Vrije Universiteit Amsterdam in 2012 among a Dutch-speaking student sample. The dataset consists of the measures described in the paper, as well as additional (exploratory measures including the Five-Factor Personality Inventory, the Connectedness to Nature Scale, the Rosenberg Self-esteem Scale and a scale measuring life stress. The data can be used for replication purposes, meta-analyses, and exploratory analyses, as well as cross-cultural comparisons of touch and/or ERN effects. The authors also welcome collaborative research based on re-analyses of the data. The data described is available at a data repository called the DANS archive: http://persistent-identifier.nl/?identifier=urn:nbn:nl:ui:13-tzbk-gg.

A prospective, randomized study addressing the need for physical simulation following virtual simulation

International Nuclear Information System (INIS)

Valicenti, Richard K.; Waterman, Frank M.; Corn, Benjamin W.; Curran, Walter J.

1997-01-01

Purpose: To accurately implement a treatment plan obtained by virtual or CT simulation, conventional or physical simulation is still widely used. To evaluate the need for physical simulation, we prospectively randomized patients to undergo physical simulation or no additional simulation after virtual simulation. Methods and Materials: From July 1995 to September 1996, 75 patients underwent conformal four-field radiation therapy planning for prostate cancer with a commercial grade CT simulator. The patients were randomized to undergo either port filming immediately following physical simulation or port filming alone. The precision of implementing the devised plan was evaluated by comparing simulator radiographs and/or port films against the digitally reconstructed radiographs (DRRs) for x, y, and z displacements of the isocenter. Changes in beam aperture were also prospectively evaluated. Results: Thirty-seven patients were randomized to undergo physical simulation and first day port filming, and 38 had first day treatment verification films only without a physical simulation. Seventy-eight simulator radiographs and 195 first day treatment port films were reviewed. There was no statistically significant reduction in treatment setup error (>5 mm) if patients underwent physical simulation following virtual simulation. No patient required a resimulation, and there was no significant difference in changes of beam aperture. Conclusions: Following virtual simulation, physical simulation may not be necessary to accurately implement the conformal four-field technique. Because port filming appears to be sufficient to assure precise and reliable execution of a devised treatment plan, physical simulation may be eliminated from the process of CT based planning when virtual simulation is available

Planetary Simulation Chambers bring Mars to laboratory studies

Energy Technology Data Exchange (ETDEWEB)

Mateo-Marti, E.

2016-07-01

Although space missions provide fundamental and unique knowledge for planetary exploration, they are always costly and extremely time-consuming. Due to the obvious technical and economical limitations of in-situ planetary exploration, laboratory simulations are among the most feasible research options for making advances in planetary exploration. Therefore, laboratory simulations of planetary environments are a necessary and complementary option to expensive space missions. Simulation chambers are economical, more versatile, and allow for a higher number of experiments than space missions. Laboratory-based facilities are able to mimic the conditions found in the atmospheres and on the surfaces of a majority of planetary objects. Number of relevant applications in Mars planetary exploration will be described in order to provide an understanding about the potential and flexibility of planetary simulation chambers systems: mainly, stability and presence of certain minerals on Mars surface; and microorganisms potential habitability under planetary environmental conditions would be studied. Therefore, simulation chambers will be a promising tools and necessary platform to design future planetary space mission and to validate in-situ measurements from orbital or rover observations. (Author)

Study of asymmetrical electric discharges using particle simulation

International Nuclear Information System (INIS)

Alves, M.V.

1990-11-01

Asymmetrical electric discharges are been widely used in the microelectronic industry. The asymmetry in the electrode areas determines the magnitude of the plasma-to-electrode voltage, V sub(a), at the powered electrode, which determines the ion bombarding energy, a critical plasma processing parameter. Two many-particle simulation codes, called P D C 1 and P D S 1, were developed. These codes are electrostatic, one-dimensional (radial) and model (a bounded plasma between two infinite cylinders or two concentric spheres that can be connected to a RLC external circuit. Both codes consider asymmetrical electrodes areas. In order to simulate electrical discharges, Monte-Carlo simulation of electron-neutral and ion-neutral collisions were included. These codes were used to study the relationship between the voltage area ratio across the sheaths, V sub(a) / V sub(b), and the electrode area ratio A sub(b) / A sub(a). Simulation results agree with experimental results and also with the analytical model that includes local ionization near the electrodes, observed to occur in almost all our simulations. (author)

Laboratory studies of photoionized plasma related to astrophysics

International Nuclear Information System (INIS)

Yang Peiqiang; Wang Feilu; Zhao Gang

2011-01-01

Photoionized plasma is universal in astronomy and has great importance on account of its close relation to compact astrophysical objects such as black holes. Recently, with the development of high energy density lasers and Z-pinch facilities, it has become possible to simulate astronomical photoionized plasma in the laboratory. These experiments help us to benchmark and modify the photoionization models, and to understand the photoionization processes to diagnose related astronomical plasma environments. (authors)

Understanding the core-halo relation of quantum wave dark matter from 3D simulations.

Science.gov (United States)

Schive, Hsi-Yu; Liao, Ming-Hsuan; Woo, Tak-Pong; Wong, Shing-Kwong; Chiueh, Tzihong; Broadhurst, Tom; Hwang, W-Y Pauchy

2014-12-31

We examine the nonlinear structure of gravitationally collapsed objects that form in our simulations of wavelike cold dark matter, described by the Schrödinger-Poisson (SP) equation with a particle mass ∼10(-22)  eV. A distinct gravitationally self-bound solitonic core is found at the center of every halo, with a profile quite different from cores modeled in the warm or self-interacting dark matter scenarios. Furthermore, we show that each solitonic core is surrounded by an extended halo composed of large fluctuating dark matter granules which modulate the halo density on a scale comparable to the diameter of the solitonic core. The scaling symmetry of the SP equation and the uncertainty principle tightly relate the core mass to the halo specific energy, which, in the context of cosmological structure formation, leads to a simple scaling between core mass (Mc) and halo mass (Mh), Mc∝a(-1/2)Mh(1/3), where a is the cosmic scale factor. We verify this scaling relation by (i) examining the internal structure of a statistical sample of virialized halos that form in our 3D cosmological simulations and by (ii) merging multiple solitons to create individual virialized objects. Sufficient simulation resolution is achieved by adaptive mesh refinement and graphic processing units acceleration. From this scaling relation, present dwarf satellite galaxies are predicted to have kiloparsec-sized cores and a minimum mass of ∼10(8)M⊙, capable of solving the small-scale controversies in the cold dark matter model. Moreover, galaxies of 2×10(12)M⊙ at z=8 should have massive solitonic cores of ∼2×10(9)M⊙ within ∼60  pc. Such cores can provide a favorable local environment for funneling the gas that leads to the prompt formation of early stellar spheroids and quasars.

Computer simulation studies in condensed-matter physics 5. Proceedings

International Nuclear Information System (INIS)

Landau, D.P.; Mon, K.K.; Schuettler, H.B.

1993-01-01

As the role of computer simulations began to increase in importance, we sensed a need for a ''meeting place'' for both experienced simulators and neophytes to discuss new techniques and results in an environment which promotes extended discussion. As a consequence of these concerns, The Center for Simulational Physics established an annual workshop on Recent Developments in Computer Simulation Studies in Condensed-Matter Physics. This year's workshop was the fifth in this series and the interest which the scientific community has shown demonstrates quite clearly the useful purpose which the series has served. The workshop was held at the University of Georgia, February 17-21, 1992, and these proceedings from a record of the workshop which is published with the goal of timely dissemination of the papers to a wider audience. The proceedings are divided into four parts. The first part contains invited papers which deal with simulational studies of classical systems and includes an introduction to some new simulation techniques and special purpose computers as well. A separate section of the proceedings is devoted to invited papers on quantum systems including new results for strongly correlated electron and quantum spin models. The third section is comprised of a single, invited description of a newly developed software shell designed for running parallel programs. The contributed presentations comprise the final chapter. (orig.). 79 figs

The IRX-β dust attenuation relation in cosmological galaxy formation simulations

Science.gov (United States)

Narayanan, Desika; Davé, Romeel; Johnson, Benjamin D.; Thompson, Robert; Conroy, Charlie; Geach, James

2018-02-01

We utilize a series of galaxy formation simulations to investigate the relationship between the ultraviolet (UV) slope, β, and the infrared excess (IRX) in the spectral energy distributions (SEDs) of galaxies. Our main goals are to understand the origin of and scatter in the IRX-β relation; to assess the efficacy of simplified stellar population synthesis screen models in capturing the essential physics in the IRX-β relation; and to understand systematic deviations from the canonical local IRX-β relations in particular populations of high-redshift galaxies. Our main results follow. Young galaxies with relatively cospatial UV and IR emitting regions and a Milky Way-like extinction curve fall on or near the standard Meurer relation. This behaviour is well captured by simplified screen models. Scatter in the IRX-β relation is dominated by three major effects: (i) older stellar populations drive galaxies below the relations defined for local starbursts due to a reddening of their intrinsic UV SEDs; (ii) complex geometries in high-z heavily star-forming galaxies drive galaxies towards blue UV slopes owing to optically thin UV sightlines; (iii) shallow extinction curves drive galaxies downwards in the IRX-β plane due to lowered near-ultraviolet/far-ultraviolet extinction ratios. We use these features of the UV slopes of galaxies to derive a fitting relation that reasonably collapses the scatter back towards the canonical local relation. Finally, we use these results to develop an understanding for the location of two particularly enigmatic populations of galaxies in the IRX-β plane: z ˜ 2-4 dusty star-forming galaxies and z > 5 star-forming galaxies.

Validation studies of the DOE-2 Building Energy Simulation Program. Final Report

Energy Technology Data Exchange (ETDEWEB)

Sullivan, R.; Winkelmann, F.

1998-06-01

This report documents many of the validation studies (Table 1) of the DOE-2 building energy analysis simulation program that have taken place since 1981. Results for several versions of the program are presented with the most recent study conducted in 1996 on version DOE-2.1E and the most distant study conducted in 1981 on version DOE-1.3. This work is part of an effort related to continued development of DOE-2, particularly in its use as a simulation engine for new specialized versions of the program such as the recently released RESFEN 3.1. RESFEN 3.1 is a program specifically dealing with analyzing the energy performance of windows in residential buildings. The intent in providing the results of these validation studies is to give potential users of the program a high degree of confidence in the calculated results. Validation studies in which calculated simulation data is compared to measured data have been conducted throughout the development of the DOE-2 program. Discrepancies discovered during the course of such work has resulted in improvements in the simulation algorithms. Table 2 provides a listing of additions and modifications that have been made to various versions of the program since version DOE-2.1A. One of the most significant recent changes in the program occurred with version DOE-2.1E. An improved algorithm for calculating the outside surface film coefficient was implemented. In addition, integration of the WINDOW 4 program was accomplished resulting in improved ability in analyzing window energy performance. Validation and verification of a program as sophisticated as DOE-2 must necessarily be limited because of the approximations inherent in the program. For example, the most accurate model of the heat transfer processes in a building would include a three-dimensional analysis. To justify such detailed algorithmic procedures would correspondingly require detailed information describing the building and/or HVAC system and energy plant parameters

Simulator Studies of the Deep Stall

Science.gov (United States)

White, Maurice D.; Cooper, George E.

1965-01-01

Simulator studies of the deep-stall problem encountered with modern airplanes are discussed. The results indicate that the basic deep-stall tendencies produced by aerodynamic characteristics are augmented by operational considerations. Because of control difficulties to be anticipated in the deep stall, it is desirable that adequate safeguards be provided against inadvertent penetrations.

Simulation Studies of Diffusion-Release and Effusive-Flow of Short-Lived Radioactive Isotopes

CERN Document Server

Zhang, Yan; Kawai, Yoko

2005-01-01

Delay times associated with diffusion release from targets and effusive-flow transport of radioactive isotopes to ion sources are principal intensity limiters at ISOL-based radioactive ion beam facilities, and simulation studies with computer models are cost effective methods for designing targets and vapor transport systems with minimum delay times to avoid excessive decay losses of short lived ion species. A finite difference code, Diffuse II, was recently developed at the Oak Ridge National Laboratory to study diffusion-release of short-lived species from three principal target geometries. Simulation results are in close agreement with analytical solutions to Fick’s second equation. Complementary to the development of Diffuse II, the Monte-Carlo code, Effusion, was developed to address issues related to the design of fast vapor transport systems. Results, derived by using Effusion, are also found to closely agree with experimental measurements. In this presentation, the codes will be used in conc...

Digital Simulation Games for Social Studies Classrooms

Science.gov (United States)

Devlin-Scherer, Roberta; Sardone, Nancy B.

2010-01-01

Data from ten teacher candidates studying teaching methods were analyzed to determine perceptions toward digital simulation games in the area of social studies. This research can be used as a conceptual model of how current teacher candidates react to new methods of instruction and determine how education programs might change existing curricula…

Individualized feedback during simulated laparoscopic training:a mixed methods study.

Science.gov (United States)

Ahlborg, Liv; Weurlander, Maria; Hedman, Leif; Nisel, Henry; Lindqvist, Pelle G; Felländer-Tsai, Li; Enochsson, Lars

2015-07-29

This study aimed to explore the value of individualized feedback on performance, flow and self-efficacy during simulated laparoscopy. Furthermore, we wished to explore attitudes towards feedback and simulator training among medical students. Sixteen medical students were included in the study and randomized to laparoscopic simulator training with or without feedback. A teacher provided individualized feedback continuously throughout the procedures to the target group. Validated questionnaires and scales were used to evaluate self-efficacy and flow. The Mann-Whitney U test was used to evaluate differences between groups regarding laparoscopic performance (instrument path length), self-efficacy and flow. Qualitative data was collected by group interviews and interpreted using inductive thematic analyses. Sixteen students completed the simulator training and questionnaires. Instrument path length was shorter in the feedback group (median 3.9 m; IQR: 3.3-4.9) as compared to the control group (median 5.9 m; IQR: 5.0-8.1), pfeedback group were more concentrated on the task and also more anxious. Both groups had high ambitions to succeed and also expressed the importance of getting feedback. The authenticity of the training scenario was important for the learning process. This study highlights the importance of individualized feedback during simulated laparoscopy training. The next step is to further optimize feedback and to transfer standardized and individualized feedback from the simulated setting to the operating room.

Magnetohydrodynamic Simulations for Studying Solar Flare Trigger Mechanism

Energy Technology Data Exchange (ETDEWEB)

Muhamad, J.; Kusano, K.; Inoue, S.; Shiota, D. [Institute for Space-Earth Environmental Research, Nagoya University, Furocho, Chikusa-ku, Nagoya, Aichi, 464-8601 (Japan)

2017-06-20

In order to understand the flare trigger mechanism, we conduct three-dimensional magnetohydrodynamic simulations using a coronal magnetic field model derived from data observed by the Hinode satellite. Several types of magnetic bipoles are imposed into the photospheric boundary of the Nonlinear Force-free Field model of Active Region (AR) NOAA 10930 on 2006 December 13, to investigate what kind of magnetic disturbance may trigger the flare. As a result, we confirm that certain small bipole fields, which emerge into the highly sheared global magnetic field of an AR, can effectively trigger a flare. These bipole fields can be classified into two groups based on their orientation relative to the polarity inversion line: the so-called opposite polarity, and reversed shear structures, as suggested by Kusano et al. We also investigate the structure of the footpoints of reconnected field lines. By comparing the distribution of reconstructed field lines and observed flare ribbons, the trigger structure of the flare can be inferred. Our simulation suggests that the data-constrained simulation, taking into account both the large-scale magnetic structure and small-scale magnetic disturbance (such as emerging fluxes), is a good way to discover a flare-producing AR, which can be applied to space weather prediction.

Mathematical and computational modeling and simulation fundamentals and case studies

CERN Document Server

Moeller, Dietmar P F

2004-01-01

Mathematical and Computational Modeling and Simulation - a highly multi-disciplinary field with ubiquitous applications in science and engineering - is one of the key enabling technologies of the 21st century. This book introduces to the use of Mathematical and Computational Modeling and Simulation in order to develop an understanding of the solution characteristics of a broad class of real-world problems. The relevant basic and advanced methodologies are explained in detail, with special emphasis on ill-defined problems. Some 15 simulation systems are presented on the language and the logical level. Moreover, the reader can accumulate experience by studying a wide variety of case studies. The latter are briefly described within the book but their full versions as well as some simulation software demos are available on the Web. The book can be used for University courses of different level as well as for self-study. Advanced sections are marked and can be skipped in a first reading or in undergraduate courses...

Simulation in an Undergraduate Nursing Pharmacology Course: A Pilot Study.

Science.gov (United States)

Tinnon, Elizabeth; Newton, Rebecca

This study examined the effectiveness of simulation as a method of teaching pharmacological concepts to nursing students; perceptions of satisfaction with simulation as a teaching strategy were also evaluated. Second-semester juniors participated in three simulations and completed the National League for Nursing Student Satisfaction and Self-Confidence in Learning Questionnaire and the Student Evaluation of Educational Quality Survey; a control group received traditional lectures. A unit exam on anticoagulant therapy content was administered to measure effectiveness. Findings support that simulation is as effective as traditional lecture for an undergraduate pharmacology course.

Criteria for safety-related nuclear-power-plant operator actions: 1982 pressurized-water-reactor (PWR) simulator exercises

International Nuclear Information System (INIS)

Crowe, D.S.; Beare, A.N.; Kozinsky, E.J.; Haas, P.M.

1983-06-01

The primary objective of the Safety-Related Operator Action (SROA) Program at Oak Ridge National Laboratory is to provide a data base to support development of criteria for safety-related actions by nuclear power plant operators. When compared to field data collected on similar events, a base of operator performance data developed from the simulator experiments can then be used to establish safety-related operator action design evaluation criteria, evaluate the effects of performance shaping factors, and support safety/risk assessment analyses. This report presents data obtained from refresher training exercises conducted in a pressurized water reactor (PWR) power plant control room simulator. The 14 exercises were performed by 24 teams of licensed operators from one utility, and operator performance was recorded by an automatic Performance Measurement System. Data tapes were analyzed to extract operator response times (RTs) and error rate information. Demographic and subjective data were collected by means of brief questionnaires and analyzed in an attempt to evaluate the effects of selected performance shaping factors on operator performance

Relate better and judge less: poverty simulation promoting culturally competent care in community health nursing.

Science.gov (United States)

Yang, Kyeongra; Woomer, Gail Ratliff; Agbemenu, Kafuli; Williams, Lynne

2014-11-01

The study aim was to evaluate the effectiveness of a poverty simulation in increasing understanding of and attitudes toward poverty and resulting in changes in clinical practice among nursing seniors. A poverty simulation was conducted using a diverse group of nursing professors and staff from local community agencies assuming the role of community resource providers. Students were assigned roles as members of low-income families and were required to complete tasks during a simulated month. A debriefing was held after the simulation to explore students' experiences in a simulated poverty environment. Students' understanding of and attitude toward poverty pre- and post-simulation were examined. Changes in the students' clinical experiences following the simulation were summarized into identified categories and themes. The poverty simulation led to a greater empathy for the possible experiences of low income individuals and families, understanding of barriers to health care, change in attitudes towards poverty and to those living in poverty, and changes in the students' nursing practice. Use of poverty simulation is an effective means to teach nursing students about the experience of living in poverty. The simulation experience changed nursing students' clinical practice, with students providing community referrals and initiating inter-professional collaborations. Copyright © 2014 Elsevier Ltd. All rights reserved.

Real time simulation techniques in Taiwan - Maanshan compact simulator

International Nuclear Information System (INIS)

Liang, K.-S.; Chuang, Y.-M.; Ko, H.-T.

2004-01-01

Recognizing the demand and potential market of simulators in various industries, a special project for real time simulation technology transfer was initiated in Taiwan in 1991. In this technology transfer program, the most advanced real-time dynamic modules for nuclear power simulation were introduced. Those modules can be divided into two categories; one is modeling related to catch dynamic response of each system, and the other is computer related to provide special real time computing environment and man-machine interface. The modeling related modules consist of the thermodynamic module, the three-dimensional core neutronics module and the advanced balance of plant module. As planned in the project, the technology transfer team should build a compact simulator for the Maanshan power plant before the end of the project to demonstrate the success of the technology transfer program. The compact simulator was designed to support the training from the regular full scope simulator which was already equipped in the Maanshan plant. The feature of this compact simulator focused on providing know-why training by the enhanced graphic display. The potential users were identified as senior operators, instructors and nuclear engineers. Total about 13 important systems were covered in the scope of the compact simulator, and multi-graphic displays from three color monitors mounted on the 10 feet compact panel were facilitated to help the user visualize detailed phenomena under scenarios of interest. (author)

Numerical relativity reaching into post-Newtonian territory: a compact-object binary simulation spanning 350 gravitational-wave cycles

Science.gov (United States)

Scheel, Mark; Szilagyi, Bela; Blackman, Jonathan; Chu, Tony; Kidder, Lawrence; Pfeiffer, Harald; Buonanno, Alessandra; Pan, Yi; Taracchini, Andrea; SXS Collaboration

2015-04-01

We present the first numerical-relativity simulation of a compact-object binary whose gravitational waveform is long enough to cover the entire frequency band of advanced gravitational-wave detectors such as LIGO, Virgo and KAGRA, for mass ratio 7 and total mass as low as 45 . 5M⊙ . We find that effective-one-body models, either uncalibrated or calibrated against substantially shorter numerical-relativity waveforms at smaller mass ratios, reproduce our new waveform remarkably well, with a loss in detection rate due to modeling error smaller than 0 . 3 % . In contrast, post-Newtonian inspiral waveforms and existing phenomenological inspiral-merger-ringdown waveforms display much greater disagreement with our new simulation. The disagreement varies substantially depending on the specific post-Newtonian approximant used.

Co-producing simulation models to inform resource management: a case study from southwest South Dakota

Science.gov (United States)

Miller, Brian W.; Symstad, Amy J.; Frid, Leonardo; Fisichelli, Nicholas A.; Schuurman, Gregor W.

2017-01-01

Simulation models can represent complexities of the real world and serve as virtual laboratories for asking “what if…?” questions about how systems might respond to different scenarios. However, simulation models have limited relevance to real-world applications when designed without input from people who could use the simulated scenarios to inform their decisions. Here, we report on a state-and-transition simulation model of vegetation dynamics that was coupled to a scenario planning process and co-produced by researchers, resource managers, local subject-matter experts, and climate change adaptation specialists to explore potential effects of climate scenarios and management alternatives on key resources in southwest South Dakota. Input from management partners and local experts was critical for representing key vegetation types, bison and cattle grazing, exotic plants, fire, and the effects of climate change and management on rangeland productivity and composition given the paucity of published data on many of these topics. By simulating multiple land management jurisdictions, climate scenarios, and management alternatives, the model highlighted important tradeoffs between grazer density and vegetation composition, as well as between the short- and long-term costs of invasive species management. It also pointed to impactful uncertainties related to the effects of fire and grazing on vegetation. More broadly, a scenario-based approach to model co-production bracketed the uncertainty associated with climate change and ensured that the most important (and impactful) uncertainties related to resource management were addressed. This cooperative study demonstrates six opportunities for scientists to engage users throughout the modeling process to improve model utility and relevance: (1) identifying focal dynamics and variables, (2) developing conceptual model(s), (3) parameterizing the simulation, (4) identifying relevant climate scenarios and management

A Comparative Study of Simulated and Measured Gear-Flap Flow Interaction

Science.gov (United States)

Khorrami, Mehdi R.; Mineck, Raymond E.; Yao, Chungsheng; Jenkins, Luther N.; Fares, Ehab

2015-01-01

The ability of two CFD solvers to accurately characterize the transient, complex, interacting flowfield asso-ciated with a realistic gear-flap configuration is assessed via comparison of simulated flow with experimental measurements. The simulated results, obtained with NASA's FUN3D and Exa's PowerFLOW® for a high-fidelity, 18% scale semi-span model of a Gulfstream aircraft in landing configuration (39 deg flap deflection, main landing gear on and off) are compared to two-dimensional and stereo particle image velocimetry measurements taken within the gear-flap flow interaction region during wind tunnel tests of the model. As part of the bench-marking process, direct comparisons of the mean and fluctuating velocity fields are presented in the form of planar contour plots and extracted line profiles at measurement planes in various orientations stationed in the main gear wake. The measurement planes in the vicinity of the flap side edge and downstream of the flap trailing edge are used to highlight the effects of gear presence on tip vortex development and the ability of the computational tools to accurately capture such effects. The present study indicates that both computed datasets contain enough detail to construct a relatively accurate depiction of gear-flap flow interaction. Such a finding increases confidence in using the simulated volumetric flow solutions to examine the behavior of pertinent aer-odynamic mechanisms within the gear-flap interaction zone.

Integrating international relations and environmental science course concepts through an interactive world politics simulation

Science.gov (United States)

Straub, K. H.; Kesgin, B.

2012-12-01

During the fall 2012 semester, students in two introductory courses at Susquehanna University - EENV:101 Environmental Science and POLI:131 World Affairs - will participate together in an online international relations simulation called Statecraft (www.statecraftsim.com). In this strategy game, students are divided into teams representing independent countries, and choose their government type (democracy, constitutional monarchy, communist totalitarian, or military dictatorship) and two country attributes (industrial, green, militaristic, pacifist, or scientific), which determine a set of rules by which that country must abide. Countries interact over issues such as resource distribution, war, pollution, immigration, and global climate change, and must also keep domestic political unrest to a minimum in order to succeed in the game. This simulation has typically been run in political science courses, as the goal is to allow students to experience the balancing act necessary to maintain control of global and domestic issues in a dynamic, diverse world. This semester, environmental science students will be integrated into the simulation, both as environmental advisers to each country and as independent actors representing groups such as Greenpeace, ExxonMobil, and UNEP. The goal in integrating the two courses in the simulation is for the students in each course to gain both 1) content knowledge of certain fundamental material in the other course, and 2) a more thorough, applied understanding of the integrated nature of the two subjects. Students will gain an appreciation for the multiple tradeoffs that decision-makers must face in the real world (economy, resources, pollution, health, defense, etc.). Environmental science students will link these concepts to the traditional course material through a "systems thinking" approach to sustainability. Political science students will face the challenges of global climate change and gain an understanding of the nature of

Generation Risk Assessment Using Fault Trees and Turbine Cycle Simulation: Case Studies

International Nuclear Information System (INIS)

Heo, Gyun Young; Park, Jin Kyun

2009-01-01

Since 2007, Korea Atomic Energy Research Institute and Kyung Hee University have collaborated on the development of the framework to quantify human errors broken out during the test and maintenance (T and M) in secondary systems of nuclear power plants (NPPs). The project entitled 'Development of Causality Analyzer for Maintenance/Test Tasks in Nuclear Power Plants' for OPR1000 on the basis of the proposed framework is still on-going, and will come to fruition by 2010. The overall concept of GRA-HRE (Generation Risk Assessment for Human Related Events) which is the designation of the framework, and the quantification methods for evaluating risk and electric loss have introduced in other references. The originality emerged while implementing GRA-HRE could be evaluated in view of (1) recognizing the relative importance of human errors comparing with other types of mechanical and/or electrical failures, (2) providing the top-down path of the propagation of human errors by designating top events in the fault tree model as trip signals, and (3) analyzing electric loss using turbine cycle simulation. Recently, we were successfully to illustrate the applicability of GRA-HRE by simulating several abnormalities. Since the detailed methodologies were released enough to follow up, this paper is going to only exemplify the case studies

Molecular dynamics simulations study of nano bubble attachment at hydrophobic surfaces

Energy Technology Data Exchange (ETDEWEB)

Jin, Jiaqi; Dang, Liem X.; Miller, Jan D.

2018-01-01

Bubble attachment phenomena are examined using Molecular Dynamics Simulations (MDS) for the first time. The simulation involves a nitrogen nano bubble containing 906 nitrogen molecules in a water phase with 74,000 water molecules at molybdenite surfaces. During a simulation period of 1 ns, film rupture and displacement occurs. The attached nanobubble at the hydrophobic molybdenite face surface results in a contact angle of about 90º. This spontaneous attachment is due to a “water exclusion zone” at the molybdenite face surface and can be explained by a van der Waals (vdW) attractive force, as discussed in the literature. In contrast, the film is stable at the hydrophilic quartz (001) surface and the bubble does not attach. Contact angles determined from MD simulations are reported, and these results agree well with experimental and MDS sessile drop results. In this way, film stability and bubble attachment are described with respect to interfacial water structure for surfaces of different polarity. Interfacial water molecules at the hydrophobic molybdenite face surface have relatively weak interactions with the surface when compared to the hydrophilic quartz (001) surface, as revealed by the presence of a 3 Å “water exclusion zone” at the molybdenite/water interface. The molybdenite armchair-edge and zigzag-edge surfaces show a comparably slow process for film rupture and displacement when compared to the molybdenite face surface, which is consistent with their relatively weak hydrophobic character.

Ethylene glycol intercalation in smectites. molecular dynamics simulation studies

International Nuclear Information System (INIS)

Szczerba, Marek; Klapyta, Zenon; Kalinichev, Andrey

2012-01-01

Document available in extended abstract form only. Intercalation of ethylene glycol in smectites (glycolation) is widely used to discriminate smectites and vermiculites from other clays and among themselves. During this process, ethylene glycol molecules enter into the interlayer spaces of the swelling clays, leading to the formation of two-layer structure (∼17 A) in the case of smectites, or one-layer structure (∼14 A) in the case of vermiculites. In spite of the relatively broad literature on the understanding/characterization of ethylene glycol/water-clays complexes, the simplified structure of this complex presented by Reynolds (1965) is still used in the contemporary X-ray diffraction computer programs, which simulate structures of smectite and illite-smectite. The monolayer structure is only approximated using the assumption of the interlayer cation and ethylene glycol molecules lying in the middle of interlayer spaces. This study was therefore undertaken to investigate the structure of ethylene glycol/water-clays complex in more detail using molecular dynamics simulation. The structural models of smectites were built on the basis of pyrophyllite crystal structure (Lee and Guggenheim, 1981), with substitution of particular atoms. In most of simulations, the structural model assumed the following composition, considered as the most common in the mixed layer illite-smectites: EXCH 0.4 (Si 3.96 Al 0.04 )(Al 1.46 Fe 0.17 Mg 0.37 )O 10 (OH) 2 Atoms of the smectites were described with CLAYFF force field (Cygan et al., 2004), while atoms of water and ethylene glycol with flexible SPC and OPLS force fields, respectively. Ewald summation was used to calculate long range Coulombic interactions and the cutoff was set at 8.5 A. Results of the simulations show that in the two-layer glycolate the content of water is relatively small: up to 0.8 H 2 O per half of the smectite unit cell. Clear thermodynamic preference of mono- or two-layer structure of the complex is

DWPF Simulant CPC Studies For SB8

Energy Technology Data Exchange (ETDEWEB)

Newell, J. D.

2013-09-25

Prior to processing a Sludge Batch (SB) in the Defense Waste Processing Facility (DWPF), flowsheet studies using simulants are performed. Typically, the flowsheet studies are conducted based on projected composition(s). The results from the flowsheet testing are used to 1) guide decisions during sludge batch preparation, 2) serve as a preliminary evaluation of potential processing issues, and 3) provide a basis to support the Shielded Cells qualification runs performed at the Savannah River National Laboratory (SRNL). SB8 was initially projected to be a combination of the Tank 40 heel (Sludge Batch 7b), Tank 13, Tank 12, and the Tank 51 heel. In order to accelerate preparation of SB8, the decision was made to delay the oxalate-rich material from Tank 12 to a future sludge batch. SB8 simulant studies without Tank 12 were reported in a separate report.1 The data presented in this report will be useful when processing future sludge batches containing Tank 12. The wash endpoint target for SB8 was set at a significantly higher sodium concentration to allow acceptable glass compositions at the targeted waste loading. Four non-coupled tests were conducted using simulant representing Tank 40 at 110-146% of the Koopman Minimum Acid requirement. Hydrogen was generated during high acid stoichiometry (146% acid) SRAT testing up to 31% of the DWPF hydrogen limit. SME hydrogen generation reached 48% of of the DWPF limit for the high acid run. Two non-coupled tests were conducted using simulant representing Tank 51 at 110-146% of the Koopman Minimum Acid requirement. Hydrogen was generated during high acid stoichiometry SRAT testing up to 16% of the DWPF limit. SME hydrogen generation reached 49% of the DWPF limit for hydrogen in the SME for the high acid run. Simulant processing was successful using previously established antifoam addition strategy. Foaming during formic acid addition was not observed in any of the runs. Nitrite was destroyed in all runs and no N2O was detected

Reservoir Simulation on the Cerro Prieto Geothermal Field: A Continuing Study

Energy Technology Data Exchange (ETDEWEB)

Castaneda, M.; Marquez, R.; Arellano, V.; Esquer, C.A.

1983-12-15

The Cerro Prieto geothermal field is a liquid-dominated geothermal reservoir of complex geological and hydrological structure. It is located at the southern end of the Salton-Mexicali trough which includes other geothermal anomalies as Heber and East Mesa. Although in 1973, the initial power plant installed capacity was 75 MW of electrical power, this amount increased to 180 MW in 1981 as field development continued. It is expected to have a generating capacity of 620 MW by the end of 1985, when two new plants will be completely in operation. Questions about field deliverability, reservoir life and ultimate recovery related to planned installations are being presently asked. Numerical modeling studies can give very valuable answers to these questions, even at the early stages in the development of a field. An effort to simulate the Cerro Prieto geothermal reservoir has been undergoing for almost two years. A joint project among Comision Federal de Electricidad (CFE), Instituto de Investigaciones Electricas (IIE) and Intercomp of Houstin, Texas, was created to perform reservoir engineering and simulation studies on this field. The final project objective is tosimulate the behavior of the old field region when production from additional wells located in the undeveloped field zones will be used for feeding the new power plants.

Simulation of groundwater flow in the Edwards-Trinity and related aquifers in the Pecos County region, Texas

Science.gov (United States)

Clark, Brian R.; Bumgarner, Johnathan R.; Houston, Natalie A.; Foster, Adam L.

2014-01-01

The Edwards-Trinity aquifer is a vital groundwater resource for agricultural, industrial, and public supply uses in the Pecos County region of western Texas. The U.S. Geological Survey completed a comprehensive, integrated analysis of available hydrogeologic data to develop a numerical groundwater-flow model of the Edwards-Trinity and related aquifers in the study area in parts of Brewster, Jeff Davis, Pecos, and Reeves Counties. The active model area covers about 3,400 square miles of the Pecos County region of Texas west of the Pecos River, and its boundaries were defined to include the saturated areas of the Edwards-Trinity aquifer. The model is a five-layer representation of the Pecos Valley, Edwards-Trinity, Dockum, and Rustler aquifers. The Pecos Valley aquifer is referred to as the alluvial layer, and the Edwards-Trinity aquifer is divided into layers representing the Edwards part of the Edwards-Trinity aquifer and the Trinity part of the Edwards-Trinity aquifer, respectively. The calibration period of the simulation extends from 1940 to 2010. Simulated hydraulic heads generally were in good agreement with observed values; 1,684 out of 2,860 (59 percent) of the simulated values were within 25 feet of the observed value. The average root mean square error value of hydraulic head for the Edwards-Trinity aquifer was 34.2 feet, which was approximately 4 percent of the average total observed change in groundwater-level altitude (groundwater level). Simulated spring flow representing Comanche Springs exhibits a pattern similar to observed spring flow. Independent geochemical modeling corroborates results of simulated groundwater flow that indicates groundwater in the Edwards-Trinity aquifer in the Leon-Belding and Fort Stockton areas is a mixture of recharge from the Barilla and Davis Mountains and groundwater that has upwelled from the Rustler aquifer.

Computational study of nonlinear plasma waves. I. Simulation model and monochromatic wave propagation

International Nuclear Information System (INIS)

Matsuda, Y.; Crawford, F.W.

1975-01-01

An economical low-noise plasma simulation model originated by Denavit is applied to a series of problems associated with electrostatic wave propagation in a one-dimensional, collisionless, Maxwellian plasma, in the absence of magnetic field. The model is described and tested, first in the absence of an applied signal, and then with a small amplitude perturbation. These tests serve to establish the low-noise features of the model, and to verify the theoretical linear dispersion relation at wave energy levels as low as 10 -6 of the plasma thermal energy: Better quantitative results are obtained, for comparable computing time, than can be obtained by conventional particle simulation models, or direct solution of the Vlasov equation. The method is then used to study propagation of an essentially monochromatic plane wave. Results on amplitude oscillation and nonlinear frequency shift are compared with available theories

Using relational databases to collect and store discrete-event simulation results

DEFF Research Database (Denmark)

Poderys, Justas; Soler, José

2016-01-01

, export the results to a data carrier file and then process the results stored in a file using the data processing software. In this work, we propose to save the simulation results directly from a simulation tool to a computer database. We implemented a link between the discrete-even simulation tool...... and the database and performed performance evaluation of 3 different open-source database systems. We show, that with a right choice of a database system, simulation results can be collected and exported up to 2.67 times faster, and use 1.78 times less disk space when compared to using simulation software built...

Simulation studies of the LAMPF proton linac

International Nuclear Information System (INIS)

Garnett, R.W.; Gray, E.R.; Rybarcyk, L.J.; Wangler, T.P.

1995-01-01

The LAMPF accelerator consists of two 0.75-MeV injectors, one for H + and the other for H - , a separate low-energy beam transport (LEBT) line for each beam species, a 0.75 to 100-MeV drift-tube linac (DTL) operating at 201.25-MHz, a 100-MeV transition region (TR), and a 100 to 800-MeV side-coupled linac (SCL) operating at 805-MHz. Each LEBT line consists of a series of quadrupoles to transport and transversely match the beam. The LEBT also contains a prebuncher, a main buncher, and an electrostatic deflector. The deflector is used to limit the fraction of a macropulse which is seen by the beam diagnostics throughout the linac. The DTL consists of four rf tanks and uses singlet FODO transverse focusing. The focusing period is doubled in the last two tanks by placing a quadrupole only in every other drift-tube. Doublet FDO transverse focusing is used in the SCL. The TR consists of separate transport lines for the H + and H - beams. The pathlengths for the two beams differ, by introducing bends, so as to delay arrival of one beam relative to the other and thereby produce the desired macropulse time structure. Peak beam currents typically range from 12 to 18-mA for varying macropulse lengths which give an average beam current of 1-mA. The number of particles per bunch is of the order 10 8 . The work presented here is an extension of previous work. The authors have attempted to do a more complete simulation by including modeling of the LEBT. No measurements of the longitudinal structure of the beam, except phase-scans, are performed at LAMPF. The authors show that, based on simulation results, the primary causes of beam spill are inefficient longitudinal capture and the lack of longitudinal matching. Measurements to support these claims are not presently made at LAMPF. However, agreement between measurement and simulation for the transverse beam properties and transmissions serve to benchmark the simulations

Three-dimensional growth simulation: A study of substrate oriented films

International Nuclear Information System (INIS)

Besnard, A; Martin, N; Carpentier, L

2010-01-01

Monte Carlo simulations are developed to simulate the growth of three-dimensional columnar microstructure in thin films. We are studying in particular oriented microstructure like those produced with the Glancing Angle Deposition technique (GLAD). Some geometrical characteristics of the particles flux, the organization of defect sites on the substrate surface and the atomic surface diffusion are mainly investigated in order to predict the growth processes and the resulting features of the films. This study reports on simulations of thin film growth exhibiting an oblique and zigzag columnar microstructure. Column angle evolution and density are investigated versus incidence angle α or period number n and compared with experimental measurements.

A study of human behavior simulation in architectural design for healthcare facilities.

Science.gov (United States)

Schaumann, Davide; Pilosof, Nirit Putievsky; Date, Kartikeya; Kalay, Yehuda E

2016-01-01

Current tools and methods in architectural design do not allow predicting and evaluating how people will use designed environments before their actual realization. To investigate how computational simulation can help in evaluating design proposals as far as their use by people is concerned. Simulation of a medicine distribution procedure in a general hospital facility, while accounting for serendipitous social interactions made possible by the presence of different users in the same space, at the same time. The simulation shows how use patterns are influenced by the social and physical context in which actors are situated, and demonstrates the significance of the proposed method of evaluating hospital designs before construction. The system allows simulating use patterns with different degrees of complexity, and enables architects to ask new types of questions related to the interactions between people and physical settings.

Numerical simulation of a semi-indirect evaporative cooler

Energy Technology Data Exchange (ETDEWEB)

Martin, R. Herrero [Departamento de Ingenieria Termica y de Fluidos, Universidad Politecnica de Cartagena, C/Dr. Fleming, s/n (Campus Muralla), 30202 Cartagena, Murcia (Spain)

2009-11-15

This paper presents the experimental study and numerical simulation of a semi-indirect evaporative cooler (SIEC), which acts as an energy recovery device in air conditioning systems. The numerical simulation was conducted by applying the CFD software FLUENT implementing a UDF to model evaporation/condensation. The numerical model was validated by comparing the simulation results with experimental data. Experimental data and numerical results agree for the lower relative humidity series but not for higher relative humidity values. (author)

Three-Dimensional Muscle Architecture and Comprehensive Dynamic Properties of Rabbit Gastrocnemius, Plantaris and Soleus: Input for Simulation Studies.

Science.gov (United States)

Siebert, Tobias; Leichsenring, Kay; Rode, Christian; Wick, Carolin; Stutzig, Norman; Schubert, Harald; Blickhan, Reinhard; Böl, Markus

2015-01-01

The vastly increasing number of neuro-muscular simulation studies (with increasing numbers of muscles used per simulation) is in sharp contrast to a narrow database of necessary muscle parameters. Simulation results depend heavily on rough parameter estimates often obtained by scaling of one muscle parameter set. However, in vivo muscles differ in their individual properties and architecture. Here we provide a comprehensive dataset of dynamic (n = 6 per muscle) and geometric (three-dimensional architecture, n = 3 per muscle) muscle properties of the rabbit calf muscles gastrocnemius, plantaris, and soleus. For completeness we provide the dynamic muscle properties for further important shank muscles (flexor digitorum longus, extensor digitorum longus, and tibialis anterior; n = 1 per muscle). Maximum shortening velocity (normalized to optimal fiber length) of the gastrocnemius is about twice that of soleus, while plantaris showed an intermediate value. The force-velocity relation is similar for gastrocnemius and plantaris but is much more bent for the soleus. Although the muscles vary greatly in their three-dimensional architecture their mean pennation angle and normalized force-length relationships are almost similar. Forces of the muscles were enhanced in the isometric phase following stretching and were depressed following shortening compared to the corresponding isometric forces. While the enhancement was independent of the ramp velocity, the depression was inversely related to the ramp velocity. The lowest effect strength for soleus supports the idea that these effects adapt to muscle function. The careful acquisition of typical dynamical parameters (e.g. force-length and force-velocity relations, force elongation relations of passive components), enhancement and depression effects, and 3D muscle architecture of calf muscles provides valuable comprehensive datasets for e.g. simulations with neuro-muscular models, development of more realistic muscle models, or

Three-Dimensional Muscle Architecture and Comprehensive Dynamic Properties of Rabbit Gastrocnemius, Plantaris and Soleus: Input for Simulation Studies.

Directory of Open Access Journals (Sweden)

Tobias Siebert

Full Text Available The vastly increasing number of neuro-muscular simulation studies (with increasing numbers of muscles used per simulation is in sharp contrast to a narrow database of necessary muscle parameters. Simulation results depend heavily on rough parameter estimates often obtained by scaling of one muscle parameter set. However, in vivo muscles differ in their individual properties and architecture. Here we provide a comprehensive dataset of dynamic (n = 6 per muscle and geometric (three-dimensional architecture, n = 3 per muscle muscle properties of the rabbit calf muscles gastrocnemius, plantaris, and soleus. For completeness we provide the dynamic muscle properties for further important shank muscles (flexor digitorum longus, extensor digitorum longus, and tibialis anterior; n = 1 per muscle. Maximum shortening velocity (normalized to optimal fiber length of the gastrocnemius is about twice that of soleus, while plantaris showed an intermediate value. The force-velocity relation is similar for gastrocnemius and plantaris but is much more bent for the soleus. Although the muscles vary greatly in their three-dimensional architecture their mean pennation angle and normalized force-length relationships are almost similar. Forces of the muscles were enhanced in the isometric phase following stretching and were depressed following shortening compared to the corresponding isometric forces. While the enhancement was independent of the ramp velocity, the depression was inversely related to the ramp velocity. The lowest effect strength for soleus supports the idea that these effects adapt to muscle function. The careful acquisition of typical dynamical parameters (e.g. force-length and force-velocity relations, force elongation relations of passive components, enhancement and depression effects, and 3D muscle architecture of calf muscles provides valuable comprehensive datasets for e.g. simulations with neuro-muscular models, development of more realistic

Glass polymorphism in glycerol-water mixtures: I. A computer simulation study.

Science.gov (United States)

Jahn, David A; Wong, Jessina; Bachler, Johannes; Loerting, Thomas; Giovambattista, Nicolas

2016-04-28

We perform out-of-equilibrium molecular dynamics (MD) simulations of water-glycerol mixtures in the glass state. Specifically, we study the transformations between low-density (LDA) and high-density amorphous (HDA) forms of these mixtures induced by compression/decompression at constant temperature. Our MD simulations reproduce qualitatively the density changes observed in experiments. Specifically, the LDA-HDA transformation becomes (i) smoother and (ii) the hysteresis in a compression/decompression cycle decreases as T and/or glycerol content increase. This is surprising given the fast compression/decompression rates (relative to experiments) accessible in MD simulations. We study mixtures with glycerol molar concentration χ(g) = 0-13% and find that, for the present mixture models and rates, the LDA-HDA transformation is detectable up to χ(g) ≈ 5%. As the concentration increases, the density of the starting glass (i.e., LDA at approximately χ(g) ≤ 5%) rapidly increases while, instead, the density of HDA remains practically constant. Accordingly, the LDA state and hence glass polymorphism become inaccessible for glassy mixtures with approximately χ(g) > 5%. We present an analysis of the molecular-level changes underlying the LDA-HDA transformation. As observed in pure glassy water, during the LDA-to-HDA transformation, water molecules within the mixture approach each other, moving from the second to the first hydration shell and filling the first interstitial shell of water molecules. Interestingly, similar changes also occur around glycerol OH groups. It follows that glycerol OH groups contribute to the density increase during the LDA-HDA transformation. An analysis of the hydrogen bond (HB)-network of the mixtures shows that the LDA-HDA transformation is accompanied by minor changes in the number of HBs of water and glycerol. Instead, large changes in glycerol and water coordination numbers occur. We also perform a detailed analysis of the effects that

Impact of subject related factors and position of flight control stick on acquisition of simulated flying skills using a flight simulator

Science.gov (United States)

Cho, Bo-Keun

Increasing demand on aviation industry calls for more pilots. Thus, pilot training systems and pilot-candidate screening systems are essential for civil and military flying training institutes. Before actual flight training, it is not easy to determine whether a flight trainee will be successful in the training. Due to the high cost of actual flight training, it would be better if there were low cost methods for screening and training candidates prior to the actual flight training. This study intended to determine if subject related factors and flight control stick position have an impact on acquisition of simulated flying skills using a PC-based flight simulator. The experimental model was a factorial design with repeated measures. Sixty-four subjects participated in the experiment and were divided into 8 groups. Experiment consisted of 8 sessions in which performance data, such as heading, altitude and airspeed were collected every 15 seconds. Collected data were analyzed using SAS statistical program. Result of multivariate analysis of variance indicated that the three independent variables: nationality, computer game experience, and flight stick position have significant impact on acquiring simulated flying skill. For nationality, Americans recorded higher scores in general (mean: 81.7) than Koreans (mean: 78.9). The difference in mean scores between Americans and Koreans was 2.8 percent. Regarding computer game experience, the difference between high experience group (82.3) and low experience group (78.3) is significant. For high experience group, American side-stick group recorded the highest (mean: 85.6), and Korean side-stick group (mean: 77.2) scored the lowest. For the low experience group, American center-stick group scored the highest (80.6), and the Korean side-stick group (74.2) scored the lowest points. Therefore, there is a significant difference between high experience group and low experience group. The results also reveal that the center

Dark Energy Studies with LSST Image Simulations, Final Report

International Nuclear Information System (INIS)

Peterson, John Russell

2016-01-01

This grant funded the development and dissemination of the Photon Simulator (PhoSim) for the purpose of studying dark energy at high precision with the upcoming Large Synoptic Survey Telescope (LSST) astronomical survey. The work was in collaboration with the LSST Dark Energy Science Collaboration (DESC). Several detailed physics improvements were made in the optics, atmosphere, and sensor, a number of validation studies were performed, and a significant number of usability features were implemented. Future work in DESC will use PhoSim as the image simulation tool for data challenges used by the analysis groups.

Genetic Simulation Tools for Post-Genome Wide Association Studies of Complex Diseases

Science.gov (United States)

Amos, Christopher I.; Bafna, Vineet; Hauser, Elizabeth R.; Hernandez, Ryan D.; Li, Chun; Liberles, David A.; McAllister, Kimberly; Moore, Jason H.; Paltoo, Dina N.; Papanicolaou, George J.; Peng, Bo; Ritchie, Marylyn D.; Rosenfeld, Gabriel; Witte, John S.

2014-01-01

Genetic simulation programs are used to model data under specified assumptions to facilitate the understanding and study of complex genetic systems. Standardized data sets generated using genetic simulation are essential for the development and application of novel analytical tools in genetic epidemiology studies. With continuing advances in high-throughput genomic technologies and generation and analysis of larger, more complex data sets, there is a need for updating current approaches in genetic simulation modeling. To provide a forum to address current and emerging challenges in this area, the National Cancer Institute (NCI) sponsored a workshop, entitled “Genetic Simulation Tools for Post-Genome Wide Association Studies of Complex Diseases” at the National Institutes of Health (NIH) in Bethesda, Maryland on March 11-12, 2014. The goals of the workshop were to: (i) identify opportunities, challenges and resource needs for the development and application of genetic simulation models; (ii) improve the integration of tools for modeling and analysis of simulated data; and (iii) foster collaborations to facilitate development and applications of genetic simulation. During the course of the meeting the group identified challenges and opportunities for the science of simulation, software and methods development, and collaboration. This paper summarizes key discussions at the meeting, and highlights important challenges and opportunities to advance the field of genetic simulation. PMID:25371374

AUV-Based Plume Tracking: A Simulation Study

Directory of Open Access Journals (Sweden)

Awantha Jayasiri

2016-01-01

Full Text Available This paper presents a simulation study of an autonomous underwater vehicle (AUV navigation system operating in a GPS-denied environment. The AUV navigation method makes use of underwater transponder positioning and requires only one transponder. A multirate unscented Kalman filter is used to determine the AUV orientation and position by fusing high-rate sensor data and low-rate information. The paper also proposes a gradient-based, efficient, and adaptive novel algorithm for plume boundary tracking missions. The algorithm follows a centralized approach and it includes path optimization features based on gradient information. The proposed algorithm is implemented in simulation on the AUV-based navigation system and successful boundary tracking results are obtained.

Framework for Architecture Trade Study Using MBSE and Performance Simulation

Science.gov (United States)

Ryan, Jessica; Sarkani, Shahram; Mazzuchim, Thomas

2012-01-01

Increasing complexity in modern systems as well as cost and schedule constraints require a new paradigm of system engineering to fulfill stakeholder needs. Challenges facing efficient trade studies include poor tool interoperability, lack of simulation coordination (design parameters) and requirements flowdown. A recent trend toward Model Based System Engineering (MBSE) includes flexible architecture definition, program documentation, requirements traceability and system engineering reuse. As a new domain MBSE still lacks governing standards and commonly accepted frameworks. This paper proposes a framework for efficient architecture definition using MBSE in conjunction with Domain Specific simulation to evaluate trade studies. A general framework is provided followed with a specific example including a method for designing a trade study, defining candidate architectures, planning simulations to fulfill requirements and finally a weighted decision analysis to optimize system objectives.

Systematic comparison of position and time dependent macroparticle simulations in beam dynamics studies

Directory of Open Access Journals (Sweden)

Ji Qiang

2002-06-01

Full Text Available Macroparticle simulation plays an important role in modern accelerator design and operation. Most linear rf accelerators have been designed based on macroparticle simulations using longitudinal position as the independent variable. In this paper, we have done a systematic comparison between using longitudinal position as the independent variable and using time as the independent variable in macroparticle simulations. We have found that, for an rms-matched beam, the maximum relative moment difference for second, fourth moments and beam maximum amplitudes between these two types of simulations is 0.25% in a 10 m reference transport system with physical parameters similar to the Spallation Neutron Source linac design. The maximum z-to- t transform error in the space-charge force calculation of the position dependent simulation is about 0.1% in such a system. This might cause a several percent error in a complete simulation of a linac with a length of hundreds of meters. Furthermore, the error may be several times larger in simulations of mismatched beams. However, if such errors are acceptable to the linac designer, then one is justified in using position dependent macroparticle simulations in this type of linac design application.

Statistical Analysis of Large Simulated Yield Datasets for Studying Climate Effects

NARCIS (Netherlands)

Makowski, D.; Asseng, S.; Ewert, F.; Bassu, S.; Durand, J.L.; Martre, P.; Adam, M.; Aggarwal, P.K.; Angulo, C.; Baron, C.; Basso, B.; Bertuzzi, P.; Biernath, C.; Boogaard, H.; Boote, K.J.; Brisson, N.; Cammarano, D.; Challinor, A.J.; Conijn, J.G.; Corbeels, M.; Deryng, D.; Sanctis, De G.; Doltra, J.; Gayler, S.; Goldberg, R.; Grassini, P.; Hatfield, J.L.; Heng, L.; Hoek, S.B.; Hooker, J.; Hunt, L.A.; Ingwersen, J.; Izaurralde, C.; Jongschaap, R.E.E.; Jones, J.W.; Kemanian, R.A.; Kersebaum, K.C.; Kim, S.H.; Lizaso, J.; Müller, C.; Naresh Kumar, S.; Nendel, C.; O'Leary, G.J.; Olesen, J.E.; Osborne, T.M.; Palosuo, T.; Pravia, M.V.; Priesack, E.; Ripoche, D.; Rosenzweig, C.; Ruane, A.C.; Sau, F.; Semenov, M.A.; Shcherbak, I.; Steduto, P.; Stöckle, C.O.; Stratonovitch, P.; Streck, T.; Supit, I.; Tao, F.; Teixeira, E.; Thorburn, P.; Timlin, D.; Travasso, M.; Roetter, R.P.; Waha, K.; Wallach, D.; White, J.W.; Williams, J.R.; Wolf, J.

2015-01-01

Many simulation studies have been carried out to predict the effect of climate change on crop yield. Typically, in such study, one or several crop models are used to simulate series of crop yield values for different climate scenarios corresponding to different hypotheses of temperature, CO2

Evaluating best educational practices, student satisfaction, and self-confidence in simulation: A descriptive study.

Science.gov (United States)

Zapko, Karen A; Ferranto, Mary Lou Gemma; Blasiman, Rachael; Shelestak, Debra

2018-01-01

The National League for Nursing (NLN) has endorsed simulation as a necessary teaching approach to prepare students for the demanding role of professional nursing. Questions arise about the suitability of simulation experiences to educate students. Empirical support for the effect of simulation on patient outcomes is sparse. Most studies on simulation report only anecdotal results rather than data obtained using evaluative tools. The aim of this study was to examine student perception of best educational practices in simulation and to evaluate their satisfaction and self-confidence in simulation. This study was a descriptive study designed to explore students' perceptions of the simulation experience over a two-year period. Using the Jeffries framework, a Simulation Day was designed consisting of serial patient simulations using high and medium fidelity simulators and live patient actors. The setting for the study was a regional campus of a large Midwestern Research 2 university. The convenience sample consisted of 199 participants and included sophomore, junior, and senior nursing students enrolled in the baccalaureate nursing program. The Simulation Days consisted of serial patient simulations using high and medium fidelity simulators and live patient actors. Participants rotated through four scenarios that corresponded to their level in the nursing program. Data was collected in two consecutive years. Participants completed both the Educational Practices Questionnaire (Student Version) and the Student Satisfaction and Self-Confidence in Learning Scale. Results provide strong support for using serial simulation as a learning tool. Students were satisfied with the experience, felt confident in their performance, and felt the simulations were based on sound educational practices and were important for learning. Serial simulations and having students experience simulations more than once in consecutive years is a valuable method of clinical instruction. When

Simulation studies on measures to mitigate ion clouds

Energy Technology Data Exchange (ETDEWEB)

Babu Ganta, Prasanth; Masood, Ahmed; Rienen, Ursula van [Universitaet Rostock, Institut fuer Allgemeine Elektrotechnik (Germany); Sauerland, Dennis; Hillert, Wolfgang [Physikalisches Institut der Universitaet Bonn, ELSA (Germany); Meseck, Atoosa [HZB, Institut Beschleunigerphysik, Berlin (Germany)

2016-07-01

For future Energy Recovery Linacs (ERL), parasitic ions, which are generated by collisions of the beam and the rest gas in the vacuum chamber, present a limiting factor for the high current-low emittance electron beams. Clearing gaps, clearing electrodes and appropriate filling patterns are a remedy to keep the ion density in the accelerator at a level that allows for a minimum stability of the beam parameters. The MOEVE PIC Tracking code, which employs a 2D wake matrix, enables tracking simulations of the ion distribution over a relatively long period of up to thousands of interactions with the passing bunches. It enables to develop a deeper understanding of the ion-cloud behavior in order to design appropriate measures for their mitigation. For certain cases, it is sufficient to study the problem in 2D. Therefore, an additional 2D solver shall be implemented into MOEVE PIC Tracking in order to reduce the computation times. Numerical studies of ion cloud dynamics in beam guiding magnets and drift sections of electron machines will be shown and compared with experimental results obtained at the ELSA facility.

Operational safety enhancement of Soviet-designed nuclear reactors via development of nuclear power plant simulators and transfer of related technology

International Nuclear Information System (INIS)

Kohut, P.; Epel, L.G.; Tutu, N.K.

1998-01-01

The US Department of Energy (DOE), under the US government's International Nuclear Safety Program (INSP), is implementing a program of developing and providing simulators for many of the Russian and Ukrainian Nuclear Power Plants (NPPs). Pacific Northwest National Laboratory (PNNL) and Brookhaven National Laboratory (BNL) manage and provide technical oversight of the various INSP simulator projects for DOE. The program also includes a simulator technology transfer process to simulator design organizations in Russia and Ukraine. Training programs, installation of new simulators, and enhancements in existing simulators are viewed as providing a relatively fast and cost-effective technology transfer that will result in measurable improvement in the safety culture and operation of NPPs. A review of this program, its present status, and its accomplishments are provided in this paper

The vibrational source strength descriptor using power input from equivalent forces: a simulation study

DEFF Research Database (Denmark)

Laugesen, Søren; Ohlrich, Mogens

1994-01-01

Simple, yet reliable methods for the approximate determination of the vibratory power supplied by the internal excitation forces of a given vibrational source are of great interest. One such method that relies on the application of a number of “equivalent forces” and measurements of the mean...... squared velocity on either the source or the receiving structure is studied in this paper by means of computer simulations. The study considers a simple system of two flexural beams coupled via a pair of springs. The investigation shows that a relatively small number of equivalent forces suffice...

Visibility Network Patterns and Methods for Studying Visual Relational Phenomena in Archeology

Directory of Open Access Journals (Sweden)

Tom Brughmans

2017-08-01

Full Text Available A review of the archeological and non-archeological use of visibility networks reveals the use of a limited range of formal techniques, in particular for representing visibility theories. This paper aims to contribute to the study of complex visual relational phenomena in landscape archeology by proposing a range of visibility network patterns and methods. We propose first- and second-order visibility graph representations of total and cumulative viewsheds, and two-mode representations of cumulative viewsheds. We present network patterns that can be used to represent aspects of visibility theories and that can be used in statistical simulation models to compare theorized networks with observed networks. We argue for the need to incorporate observed visibility network density in these simulation models, by illustrating strong differences in visibility network density in three example landscapes. The approach is illustrated through a brief case study of visibility networks of long barrows in Cranborne Chase.

Molecular simulation studies on thermophysical properties with application to working fluids

CERN Document Server

Raabe, Gabriele

2017-01-01

This book discusses the fundamentals of molecular simulation, starting with the basics of statistical mechanics and providing introductions to Monte Carlo and molecular dynamics simulation techniques. It also offers an overview of force-field models for molecular simulations and their parameterization, with a discussion of specific aspects. The book then summarizes the available know-how for analyzing molecular simulation outputs to derive information on thermophysical and structural properties. Both the force-field modeling and the analysis of simulation outputs are illustrated by various examples. Simulation studies on recently introduced HFO compounds as working fluids for different technical applications demonstrate the value of molecular simulations in providing predictions for poorly understood compounds and gaining a molecular-level understanding of their properties. This book will prove a valuable resource to researchers and students alike.

Sequential Computerized Mastery Tests--Three Simulation Studies

Science.gov (United States)

Wiberg, Marie

2006-01-01

A simulation study of a sequential computerized mastery test is carried out with items modeled with the 3 parameter logistic item response theory model. The examinees' responses are either identically distributed, not identically distributed, or not identically distributed together with estimation errors in the item characteristics. The…

Realization of a Desktop Flight Simulation System for Motion-Cueing Studies

Directory of Open Access Journals (Sweden)

Berkay Volkaner

2016-05-01

Full Text Available Parallel robotic mechanisms are generally used in flight simulators with a motion-cueing algorithm to create an unlimited motion feeling of a simulated medium in a bounded workspace of the simulator. A major problem in flight simulators is that the simulation has an unbounded space and the manipulator has a limited one. Using a washout filter in the motion-cueing algorithm overcomes this. In this study, a low-cost six degrees of freedom (DoF desktop parallel manipulator is used to test a classical motion-cueing algorithm; the algorithm's functionality is confirmed with a Simulink real-time environment. Translational accelerations and angular velocities of the simulated medium obtained from FlightGear flight simulation software are processed through a generated washout filter algorithm and the simulated medium's motion information is transmitted to the desktop parallel robotic mechanism as a set point for each leg. The major issues of this paper are designing a desktop simulation system, controlling the parallel manipulator, communicating between the flight simulation and the platform, designing a motion-cueing algorithm and determining the parameters of the washout filters.

Shuttle/TDRSS modelling and link simulation study

Science.gov (United States)

Braun, W. R.; Mckenzie, T. M.; Biederman, L.; Lindsey, W. C.

1979-01-01

A Shuttle/TDRSS S-band and Ku-band link simulation package called LinCsim was developed for the evaluation of link performance for specific Shuttle signal designs. The link models were described in detail and the transmitter distortion parameters or user constraints were carefully defined. The overall link degradation (excluding hardware degradations) relative to an ideal BPSK channel were given for various sets of user constraint values. The performance sensitivity to each individual user constraint was then illustrated. The effect of excessive Spacelab clock jitter on the return link BER performance was also investigated as was the problem of subcarrier recovery for the K-band Shuttle return link signal.

A simulation study of interface mixing during ion-assisted deposition

International Nuclear Information System (INIS)

Wenzhi Li; Fuzhai Cui; Yi Liao; Hengde Li

1990-01-01

Ion-beam assisted deposition (IAD) can produce strong film to substrate adhesion. The adhesion depends heavily on atom mixing near the interface. In order to study the dependence of the width of the mixed interface on the experimental parameters, a Monte Carlo study has been made using the dynamic simulation code TCIS-6. The simulation mode and calculational procedure are described. Simulation calculations indicate that the mixing increases with the bombarding energies and a saturation width appears at high energies. There is a strong relationship between the amount of mixing and the ion-to-atom arrival ratio. Some comparisons of the calculations with experimental data in the literature are also presented. (author)

Molecular Simulation Study of Montmorillonite in Contact with Variably Wet Supercritical Carbon Dioxide

KAUST Repository

Kadoura, Ahmad Salim

2017-03-07

We perform grand canonical Monte Carlo simulations to study the detailed molecular mechanism of intercalation behavior of CO2 in Na-, Ca-, and Mg- montmorillonite exposed to variably hydrated supercritical CO2 at 323.15 K and 90 bar, The simulations indicate that the intercalation of CO2 strongly depends on the relative humidity (RH). The intercalation of CO2 in the dehydrated interlayer is inhibited, followed by the swelling of the interlayer region due to uptake of water and CO2 as the RH increases. In all of the hydrated clay samples, the amount of the intercalated CO2 generally decreases as a function of increasing RH, which is attributed mainly to the weakening of the interaction between CO2 and clay. At low RH values, Ca- and Mg- montmorillonite are relatively more efficient in capturing CO2. The amount of CO2 trapped in all clay samples shows similar values above RH of similar to 60%. Molecular dynamics simulations show that the diffusion coefficient of each species generally increases with increasing RH due to the associated expansion of the interlayer distance of the clay. For all the hydrated samples, the diffusion coefficients of CO2 and water in the interlayers are mostly comparable due to the fact that CO2 molecules are well solvated. The diffusion of CO2 in each hydration state is mostly independent of the type of cation in accordance with the fact that CO2 molecules hardly migrate into the first hydration shell of the interlayer cations.

Simulating direct shear tests with the Bullet physics library: A validation study.

Science.gov (United States)

Izadi, Ehsan; Bezuijen, Adam

2018-01-01

This study focuses on the possible uses of physics engines, and more specifically the Bullet physics library, to simulate granular systems. Physics engines are employed extensively in the video gaming, animation and movie industries to create physically plausible scenes. They are designed to deliver a fast, stable, and optimal simulation of certain systems such as rigid bodies, soft bodies and fluids. This study focuses exclusively on simulating granular media in the context of rigid body dynamics with the Bullet physics library. The first step was to validate the results of the simulations of direct shear testing on uniform-sized metal beads on the basis of laboratory experiments. The difference in the average angle of mobilized frictions was found to be only 1.0°. In addition, a very close match was found between dilatancy in the laboratory samples and in the simulations. A comprehensive study was then conducted to determine the failure and post-failure mechanism. We conclude with the presentation of a simulation of a direct shear test on real soil which demonstrated that Bullet has all the capabilities needed to be used as software for simulating granular systems.

COMPARATIVE STUDY OF TERTIARY WASTEWATER TREATMENT BY COMPUTER SIMULATION

Directory of Open Access Journals (Sweden)

Stefania Iordache

2010-01-01

Full Text Available The aim of this work is to asses conditions for implementation of a Biological Nutrient Removal (BNR process in theWastewater Treatment Plant (WWTP of Moreni city (Romania. In order to meet the more increased environmentalregulations, the wastewater treatment plant that was studied, must update the actual treatment process and have tomodernize it. A comparative study was undertaken of the quality of effluents that could be obtained by implementationof biological nutrient removal process like A2/O (Anaerobic/Anoxic/Oxic and VIP (Virginia Plant Initiative aswastewater tertiary treatments. In order to asses the efficiency of the proposed treatment schemata based on the datamonitored at the studied WWTP, it were realized computer models of biological nutrient removal configurations basedon A2/O and VIP process. Computer simulation was realized using a well-known simulator, BioWin by EnviroSimAssociates Ltd. The simulation process allowed to obtain some data that can be used in design of a tertiary treatmentstage at Moreni WWTP, in order to increase the efficiency in operation.

Analysis of the Accuracy and Performance of a Continuous Glucose Monitoring Sensor Prototype: An In-Silico Study Using the UVA/PADOVA Type 1 Diabetes Simulator.

Science.gov (United States)

Breton, Marc D; Hinzmann, Rolf; Campos-Nañez, Enrique; Riddle, Susan; Schoemaker, Michael; Schmelzeisen-Redeker, Guenther

2017-05-01

Computer simulation has been shown over the past decade to be a powerful tool to study the impact of medical devices characteristics on clinical outcomes. Specifically, in type 1 diabetes (T1D), computer simulation platforms have all but replaced preclinical studies and are commonly used to study the impact of measurement errors on glycemia. We use complex mathematical models to represent the characteristics of 3 continuous glucose monitoring systems using previously acquired data. Leveraging these models within the framework of the UVa/Padova T1D simulator, we study the impact of CGM errors in 6 simulation scenarios designed to generate a wide variety of glycemic conditions. Assessment of the simulated accuracy of each different CGM systems is performed using mean absolute relative deviation (MARD) and precision absolute relative deviation (PARD). We also quantify the capacity of each system to detect hypoglycemic events. The simulated Roche CGM sensor prototype (RCGM) outperformed the 2 alternate systems (CGM-1 & CGM-2) in accuracy (MARD = 8% vs 11.4% vs 18%) and precision (PARD = 6.4% vs 9.4% vs 14.1%). These results held for all studied glucose and rate of change ranges. Moreover, it detected more than 90% of hypoglycemia, with a mean time lag less than 4 minutes (CGM-1: 86%/15 min, CGM-2: 57%/24 min). The RCGM system model led to strong performances in these simulation studies, with higher accuracy and precision than alternate systems. Its characteristics placed it firmly as a strong candidate for CGM based therapy, and should be confirmed in large clinical studies.

Team play in surgical education: a simulation-based study.

Science.gov (United States)

Marr, Mollie; Hemmert, Keith; Nguyen, Andrew H; Combs, Ronnie; Annamalai, Alagappan; Miller, George; Pachter, H Leon; Turner, James; Rifkind, Kenneth; Cohen, Steven M

2012-01-01

Simulation-based training provides a low-stress learning environment where real-life emergencies can be practiced. Simulation can improve surgical education and patient care in crisis situations through a team approach emphasizing interpersonal and communication skills. This study assessed the effects of simulation-based training in the context of trauma resuscitation in teams of trainees. In a New York State-certified level I trauma center, trauma alerts were assessed by a standardized video review process. Simulation training was provided in various trauma situations followed by a debriefing period. The outcomes measured included the number of healthcare workers involved in the resuscitation, the percentage of healthcare workers in role position, time to intubation, time to intubation from paralysis, time to obtain first imaging study, time to leave trauma bay for computed tomography scan or the operating room, presence of team leader, and presence of spinal stabilization. Thirty cases were video analyzed presimulation and postsimulation training. The two data sets were compared via a 1-sided t test for significance (p role positions increased from 57.8% to 83.6% (p = 0.46). The time to intubation from paralysis decreased from 3.9 to 2.8 minutes (p team leader increased from 64% to 90% (p team interaction and educational competencies. Providing simulation training as a tool for surgical education may enhance patient care. Copyright © 2012 Association of Program Directors in Surgery. Published by Elsevier Inc. All rights reserved.

An exploration of the relationship between knowledge and performance-related variables in high-fidelity simulation: designing instruction that promotes expertise in practice.

Science.gov (United States)

Hauber, Roxanne P; Cormier, Eileen; Whyte, James

2010-01-01

Increasingly, high-fidelity patient simulation (HFPS) is becoming essential to nursing education. Much remains unknown about how classroom learning is connected to student decision-making in simulation scenarios and the degree to which transference takes place between the classroom setting and actual practice. The present study was part of a larger pilot study aimed at determining the relationship between nursing students' clinical ability to prioritize their actions and the associated cognitions and physiologic outcomes of care using HFPS. In an effort to better explain the knowledge base being used by nursing students in HFPS, the investigators explored the relationship between common measures of knowledge and performance-related variables. Findings are discussed within the context of the expert performance approach and concepts from cognitive psychology, such as cognitive architecture, cognitive load, memory, and transference.

Best practices across surgical specialties relating to simulation-based training.

Science.gov (United States)

Gardner, Aimee K; Scott, Daniel J; Pedowitz, Robert A; Sweet, Robert M; Feins, Richard H; Deutsch, Ellen S; Sachdeva, Ajit K

2015-11-01

Simulation-based training is playing an increasingly important role in surgery. However, there is insufficient discussion among the surgical specialties regarding how simulation may best be leveraged for training. There is much to be learned from one another as we all strive to meet new requirements within the context of Undergraduate Medical Education, Graduate Medical Education, and Continuing Medical Education. To address this need, a panel was convened at the 6th Annual Meeting of the Consortium of the American College of Surgeons-Accredited Education Institutes consisting of key leaders in the field of simulation from 4 surgical subspecialties, namely, general surgery, orthopedic surgery, cardiothoracic surgery, urology, and otolaryngology. An overview of how the 5 surgical specialties are using simulation-based training to meet a wide array of educational needs for all levels of learners is presented. Copyright © 2015 Elsevier Inc. All rights reserved.

Simulating spatial and temporally related fire weather

Science.gov (United States)

Isaac C. Grenfell; Mark Finney; Matt Jolly

2010-01-01

Use of fire behavior models has assumed an increasingly important role for managers of wildfire incidents to make strategic decisions. For fire risk assessments and danger rating at very large spatial scales, these models depend on fire weather variables or fire danger indices. Here, we describe a method to simulate fire weather at a national scale that captures the...

Gender differences in alcohol impairment of simulated driving performance and driving-related skills.

Science.gov (United States)

Miller, Melissa A; Weafer, Jessica; Fillmore, Mark T

2009-01-01

Considerable laboratory research indicates that moderate doses of alcohol impair a broad range of skilled activities related to driving performance in young adults. Although laboratory studies show that the intensity of impairment is generally dependent on the blood alcohol concentration, some reviews of this literature suggest that women might be more sensitive to the impairing effects of alcohol than men. The present study tested this hypothesis. Drawing on data from previous experiments in our laboratory, we compared men and women in terms of the degree to which a challenge dose of alcohol (0.65 g/kg) impaired their simulated driving performance and measures of three separate behavioral and cognitive functions important to driving performance: motor coordination, speed of information processing and information-processing capacity. Alcohol significantly impaired all aspects of performance. Moreover, women displayed greater impairment than men on all behavioral tests and also reported higher levels of subjective intoxication compared with men. Both biological and social-cultural factors have been implicated in gender differences in the behavioral responses to alcohol. The current evidence of heightened sensitivity to alcohol in women highlights the need for better understanding the biological and environmental factors underlying this gender difference.

Statistical Analysis of Large Simulated Yield Datasets for Studying Climate Effects

Science.gov (United States)

Makowski, David; Asseng, Senthold; Ewert, Frank; Bassu, Simona; Durand, Jean-Louis; Martre, Pierre; Adam, Myriam; Aggarwal, Pramod K.; Angulo, Carlos; Baron, Chritian;

Pilot study on indoor climate investigation and computer simulation in historical museum building: Amerongen Castle, the Netherlands

Directory of Open Access Journals (Sweden)

Raha Sulaiman

2010-12-01

Full Text Available The indoor climate is one of the most important factors contributing to climate-induced damage to the building materials and cultural collections of a monumental building. The Dutch monumental building - Amerongen Castle, and the collections housed in it show severe deterioration caused by inappropriate historical indoor environment. Assessments of the indoor climate, especially on the room temperature and relative humidity, are necessary to analyze the causes and impacts of climate change. As the building was flooded in year 1993 and 1996, extra attention is paid to investigate the effects of flooding to it. This pilot study was aimed to identify the buildup linkages between the known past, historical data on indoor environment and indoor climate performance in the building through simulation based-prediction. This paper focuses on the methodology of indoor climate investigation from the past to the current situation. A hypothesis was developed on backcasting-based prediction simulation which can be used to identify the accepted historical indoor climate where during those times there probably was no damage to the building and the collection. A simulation method based on heat, air and moisture transport is used with the HAMBase program. The computer model representing the Grand Salon of Amerongen Castle was calibrated by comparing real measurements to simulation results. It shows that the differences were only to the minimum of -1.8C and maximum of 3.2C. The data for the historical outdoor weather files was obtained by interpolating outdoor ancient climatology constructed by MATLAB. Based on archival research, indoor thermal history was gathered as input for the profiles used in simulation. Further, the calibrated computer model can be used to simulate past indoor climate and investigate the process of the deterioration of the room and the collections mainly due to the fluctuation of indoor temperature and relative humidity. At the end

Simulation and the Development of Clinical Judgment: A Quantitative Study

Science.gov (United States)

Holland, Susan

2015-01-01

The purpose of this quantitative pretest posttest quasi-experimental research study was to explore the effect of the NESD on clinical judgment in associate degree nursing students and compare the differences between groups when the Nursing Education Simulation Design (NESD) guided simulation in order to identify educational strategies promoting…

Approaching the Post-Newtonian Regime with Numerical Relativity: A Compact-Object Binary Simulation Spanning 350 Gravitational-Wave Cycles.

Science.gov (United States)

Szilágyi, Béla; Blackman, Jonathan; Buonanno, Alessandra; Taracchini, Andrea; Pfeiffer, Harald P; Scheel, Mark A; Chu, Tony; Kidder, Lawrence E; Pan, Yi

2015-07-17

We present the first numerical-relativity simulation of a compact-object binary whose gravitational waveform is long enough to cover the entire frequency band of advanced gravitational-wave detectors, such as LIGO, Virgo, and KAGRA, for mass ratio 7 and total mass as low as 45.5M_{⊙}. We find that effective-one-body models, either uncalibrated or calibrated against substantially shorter numerical-relativity waveforms at smaller mass ratios, reproduce our new waveform remarkably well, with a negligible loss in detection rate due to modeling error. In contrast, post-Newtonian inspiral waveforms and existing calibrated phenomenological inspiral-merger-ringdown waveforms display greater disagreement with our new simulation. The disagreement varies substantially depending on the specific post-Newtonian approximant used.

Do Simulated Gambling Activities Predict Gambling with Real Money During Adolescence? Empirical Findings from a Longitudinal Study.

Science.gov (United States)

Hayer, Tobias; Kalke, Jens; Meyer, Gerhard; Brosowski, Tim

2018-02-12

As technology has developed, the international gambling market has changed markedly in recent years. The supply of internet-based gambling opportunities has become ever more significant. At the same time, the introduction of new gambling opportunities always brings a demand for evidence-based scientific evaluation, with regard to the associated risks of addiction. Simulated internet gambling, which is the focus of this study, represents a relatively new product group located at the interface between gambling and computer gaming. Concerns have been raised in scientific literature, especially with regard to the adolescent age group, as to whether participation in simulated internet gambling directly promotes recruitment to the world of monetary gambling, as defined in the gateway hypothesis. The research design was based on a standardized, representative longitudinal survey (over a 1-year period) with a total of 1178 school pupils from Northern Germany (M = 13.6 years; 47.5% male). It must be borne in mind that 12% of the adolescents belonged to the subgroup of "onset gamblers" and first reported experience with monetary gambling at the second stage of surveying. Logistic regression analysis demonstrates that this migration process is fostered by (1) participation from home in simulated gambling on social networks and (2) significant exposure to advertising (relating to both simulated and monetary gambling). Within the subgroup of simulated internet gamblers, variables such as particular patterns of use (including breadth and depth of involvement with simulated internet gambling, certain motives for participation, and microtransactions) do not serve as significant predictors. Despite this, important needs for action for the purposes of prevention and research can be identified.

Ion bombardment simulation: a review related to fusion radiation damage

International Nuclear Information System (INIS)

Brimhall, J.L.

1975-01-01

Prime emphasis is given to reviewing the ion bombardment data on the refractory metals molybdenum, niobium and vanadium which have been proposed for use in advanced fusion devices. The temperature and dose dependence of the void parameters are correlated among these metals. The effect of helium and hydrogen gas on the void parameters is also included. The similarities and differences of the response of these materials to high dose, high temperature radiation damage are evaluated. Comparisons are made with results obtained from stainless steel and nickel base alloys. The ion bombardment data is then compared and correlated, as far as possible, with existing neutron data on the refractory metals. The theoretically calculated damage state produced by neutrons and ions is also briefly discussed and compared to experimental data wherever possible. The advantages and limitations of ion simulation in relation to fusion radiation damage are finally summarized

Theoretical studies of zirconium and carbon clusters with molecular dynamics simulations

International Nuclear Information System (INIS)

Zhang, B.

1993-01-01

With the aim of understanding the anomalous phonon behavior near the martensitic phase transition in Zr, we have simulated the dynamics of atomic motion in the high temperature bcc phase of Zr using an embedded-atom potential. The calculated dynamical structure factors reproduce the strong asymmetry in the scattering cross-sections in different Brillouin zones observed in inelastic neutron scattering experiments. From the real-space atomic picture, we observed the phase fluctuations between bcc and low temperature phase hcp. The anomalous phonon behavior arises from the incompleteness of the phase fluctuations. Combining an efficient simulated annealing scheme for generating closed, hollow, spheroidal cage structures with a tight-binding molecular-dynamics method for energy optimization. We have systematically studied the ground-state structure of every even-numbered carbon fullerene from C 20 to C 100 . Clusters of sizes 60, 70, and 84 are found to be energetically more stable than their neighbors. Most ground-state structures of fullerenes have relatively low symmetries. In many cases, several isomers of a fullerene are found to have competitively low energies, which suggests that a mixture of these isomers can be observed in experimentally prepared samples. We also simulate the collisions between fullerene and the thermal disintegration of fullerenes. We observed three different regimes of behavior as the collisions become more and more energetic: bouncing, fusion and fragmentation. The critical energies for fusion and fragmentation as well as details of the energy transfer process during the collisions are investigated. In simulations of the thermal disintegration of fullerene cages, the most commonly observed fragments after the disintegration of the carbon cages are dimers, rings, and multiple rings. The fragmentation temperature increases almost linearly with cluster size for small cages (n ≤ 58), but remains constant for larger fullerenes

Defining the Simulation Technician Role: Results of a Survey-Based Study.

Science.gov (United States)

Bailey, Rachel; Taylor, Regina G; FitzGerald, Michael R; Kerrey, Benjamin T; LeMaster, Thomas; Geis, Gary L

2015-10-01

In health care simulation, simulation technicians perform multiple tasks to support various educational offerings. Technician responsibilities and the tasks that accompany them seem to vary between centers. The objectives were to identify the range and frequency of tasks that technicians perform and to determine if there is a correspondence between what technicians do and what they feel their responsibilities should be. We hypothesized that there is a core set of responsibilities and tasks for the technician position regardless of background, experience, and type of simulation center. We conducted a prospective, survey-based study of individuals currently functioning in a simulation technician role in a simulation center. This survey was designed internally and piloted within 3 academic simulation centers. Potential respondents were identified through a national mailing list, and the survey was distributed electronically during a 3-week period. A survey request was sent to 280 potential participants, 136 (49%) responded, and 73 met inclusion criteria. Five core tasks were identified as follows: equipment setup and breakdown, programming scenarios into software, operation of software during simulation, audiovisual support for courses, and on-site simulator maintenance. Independent of background before they were hired, technicians felt unprepared for their role once taking the position. Formal training was identified as a need; however, the majority of technicians felt experience over time was the main contributor toward developing knowledge and skills within their role. This study represents a first step in defining the technician role within simulation-based education and supports the need for the development of a formal job description to allow recruitment, development, and certification.

Preliminary simulation studies of accelerator cavity loading

International Nuclear Information System (INIS)

Faehl, R.J.

1980-06-01

Two-dimensional simulations of loading effects in a 350 MHz accelerator cavity have been performed. Electron currents of 1-10 kA have been accelerated in 5 MV/m fields. Higher order cavity modes induced by the beam may lead to emittance growth. Operation in an autoaccelerator mode has been studied

Study of dissolution precipitation phenomena related to heat generated by underground disposal

International Nuclear Information System (INIS)

Fabriol, R.

1987-01-01

This study is composed of two parts developed in two separated volumes. The first part is a bibliographical research concerning the behaviour of waste analog elements during hydrothermal alteration in active geothermal fields. The second part is an experimental and theoretical simulation of dissolution-precipitation phenomena related to heat generated in the vicinity of a nuclear waste repository located in granitic formations. This work is part of the CEC project MIRAGE on natural geological migration systems [fr

Molecular Simulation Studies of Covalently and Ionically Grafted Nanoparticles

Science.gov (United States)

Hong, Bingbing

Solvent-free covalently- or ionically-grafted nanoparticles (CGNs and IGNs) are a new class of organic-inorganic hybrid composite materials exhibiting fluid-like behaviors around room temperature. With similar structures to prior systems, e.g. nanocomposites, neutral or charged colloids, ionic liquids, etc, CGNs and IGNs inherit the functionality of inorganic nanopariticles, the facile processibility of polymers, as well as conductivity and nonvolatility from their constituent materials. In spite of the extensive prior experimental research having covered synthesis and measurements of thermal and dynamic properties, little progress in understanding of these new materials at the molecular level has been achieved, because of the lack of simulation work in this new area. Atomistic and coarse-grained molecular dynamics simulations have been performed in this thesis to investigate the thermodynamics, structure, and dynamics of these systems and to seek predictive methods predictable for their properties. Starting from poly(ethylene oxide) oligomers (PEO) melts, we established atomistic models based on united-atom representations of methylene. The Green-Kubo and Einstein-Helfand formulas were used to calculate the transport properties. The simulations generate densities, viscosities, diffusivities, in good agreement with experimental data. The chain-length dependence of the transport properties suggests that neither Rouse nor reptation models are applicable in the short-chain regime investigated. Coupled with thermodynamic integration methods, the models give good predictions of pressure-composition-density relations for CO 2 + PEO oligomers. Water effects on the Henry's constant of CO 2 in PEO have also been investigated. The dependence of the calculated Henry's constants on the weight percentage of water falls on a temperature-dependent master curve, irrespective of PEO chain length. CGNs are modeled by the inclusion of solid-sphere nanoparticles into the atomistic

Study on computer-aided simulation procedure for multicomponent separating cascade

International Nuclear Information System (INIS)

Kinoshita, Masahiro

1982-11-01

The present report reviews the author's study on the computer-aided simulation procedure for a multicomponent separating cascade. As a conclusion, two very powerful simulation procedures have been developed for cascades composed of separating elements whose separation factors are very large. They are applicable in cases where interstage flow rates are input variables for the calculation and stage separation factors are given either as constants or as functions of compositions of the up and down streams. As an application of the new procedure, a computer-aided simulation study has been performed for hydrogen isotope separating cascades by porous membrane method. A cascade system configuration is developed and pertinent design specifications are determined in an example case of the feed conditions and separation requirements. (author)

Challenging stereotyping and bias: a voice simulation study.

Science.gov (United States)

Dearing, Karen S; Steadman, Sheryl

2008-02-01

Stigma is a barrier to mental health care access for patients with schizophrenia and can interfere with developing therapeutic relationships. This study demonstrates success of a voice simulation experience during orientation in changing the biases of nursing students and the effect on the development of the nurse-patient relationship. Ninety-four individuals participated; 52 received a voice simulation experience during orientation, and 42 received orientation with no voice simulation experience. The Medical Condition Regard Scale was administered before and after orientation. Posttest paired t test results show significant differences in attitudes toward patients with voice hearing experiences between the two groups. The themes of personal growth from the focus groups postorientation include Affective Experience, Physical Experience, and Empathy. Findings demonstrate that the orientation process should include methods to challenge stereotyping and bias to decrease stigma, improve service access, and enhance the ability to develop therapeutic relationships.

Numerical Simulations of Kinetic Alfvén Waves to Study Spectral ...

Indian Academy of Sciences (India)

Numerical Simulations of Kinetic Alfvén Waves to Study Spectral. Index in Solar Wind Turbulence and Particle Heating. R. P. Sharma. ∗. & H. D. Singh. Center for Energy Studies, Indian Institute of Technology, Delhi 110 016, India. ∗ e-mail: rpsharma@ces.iitd.ernet.in. Abstract. We present numerical simulations of the ...

A randomised, simulated study assessing auscultation of heart rate at birth

NARCIS (Netherlands)

Voogdt, Kevin G. J. A.; Morrison, Allison C.; Wood, Fiona E.; van Elburg, Ruurd M.; Wyllie, Jonathan P.

2010-01-01

Heart rate is a primary clinical indicator directing newborn resuscitation. The time taken to assess the heart rate by auscultation in relation to accuracy during newborn resuscitation is not known. To assess both the accuracy and time taken to assess heart rate by stethoscope in simulated

Review of Methods Related to Assessing Human Performance in Nuclear Power Plant Control Room Simulations

Energy Technology Data Exchange (ETDEWEB)

Katya L Le Blanc; Ronald L Boring; David I Gertman

2001-11-01

With the increased use of digital systems in Nuclear Power Plant (NPP) control rooms comes a need to thoroughly understand the human performance issues associated with digital systems. A common way to evaluate human performance is to test operators and crews in NPP control room simulators. However, it is often challenging to characterize human performance in meaningful ways when measuring performance in NPP control room simulations. A review of the literature in NPP simulator studies reveals a variety of ways to measure human performance in NPP control room simulations including direct observation, automated computer logging, recordings from physiological equipment, self-report techniques, protocol analysis and structured debriefs, and application of model-based evaluation. These methods and the particular measures used are summarized and evaluated.

Simulation Use in Paramedic Education Research (SUPER): A Descriptive Study.

Science.gov (United States)

McKenna, Kim D; Carhart, Elliot; Bercher, Daniel; Spain, Andrew; Todaro, John; Freel, Joann

2015-01-01

The purpose of this research was to characterize the use of simulation in initial paramedic education programs in order assist stakeholders' efforts to target educational initiatives and resources. This group sought to provide a snapshot of what simulation resources programs have or have access to and how they are used; faculty perceptions about simulation; whether program characteristics, resources, or faculty training influence simulation use; and if simulation resources are uniform for patients of all ages. This was a cross-sectional census survey of paramedic programs that were accredited or had a Letter of Review from the Committee on Accreditation of Educational Programs for the EMS Professions at the time of the study. The data were analyzed using descriptive statistics and chi-square analyses. Of the 638 surveys sent, 389 valid responses (61%) were analyzed. Paramedic programs reported they have or have access to a wide range of simulation resources (task trainers [100%], simple manikins [100%], intermediate manikins [99%], advanced/fully programmable manikins [91%], live simulated patients [83%], computer-based [71%], and virtual reality [19%]); however, they do not consistently use them, particularly advanced (71%), live simulated patients (66%), computer-based (games, scenarios) (31%), and virtual reality (4%). Simulation equipment (of any type) reportedly sits idle and unused in (31%) of programs. Lack of training was cited as the most common reason. Personnel support specific to simulation was available in 44% of programs. Programs reported using simulation to replace skills more frequently than to replace field or clinical hours. Simulation goals included assessment, critical thinking, and problem-solving most frequently, and patient and crew safety least often. Programs using advanced manikins report manufacturers as their primary means of training (87%) and that 19% of faculty had no training specific to those manikins. Many (78%) respondents felt

Mobile-ip Aeronautical Network Simulation Study

Science.gov (United States)

Ivancic, William D.; Tran, Diepchi T.

2001-01-01

NASA is interested in applying mobile Internet protocol (mobile-ip) technologies to its space and aeronautics programs. In particular, mobile-ip will play a major role in the Advanced Aeronautic Transportation Technology (AATT), the Weather Information Communication (WINCOMM), and the Small Aircraft Transportation System (SATS) aeronautics programs. This report presents the results of a simulation study of mobile-ip for an aeronautical network. The study was performed to determine the performance of the transmission control protocol (TCP) in a mobile-ip environment and to gain an understanding of how long delays, handoffs, and noisy channels affect mobile-ip performance.

Post-processing of Monte Carlo simulations for rapid BNCT source optimization studies

International Nuclear Information System (INIS)

Bleuel, D.L.; Chu, W.T.; Donahue, R.J.; Ludewigt, B.A.; Vujic, J.

2000-01-01

A great advantage of some neutron sources, such as accelerator-produced sources, is that they can be tuned to produce different spectra. Unfortunately, optimization studies are often time-consuming and difficult, as they require a lengthy Monte Carlo simulation for each source. When multiple characteristics, such as energy, angle, and spatial distribution of a neutron beam are allowed to vary, an overwhelming number of simulations may be required. Many optimization studies, therefore, suffer from a small number of datapoints, restrictive treatment conditions, or poor statistics. By scoring pertinent information from every particle tally in a Monte Carlo simulation, then applying appropriate source variable weight factors in a post-processing algorithm, a single simulation can be used to model any number of multiple sources. Through this method, the response to a new source can be modeled in minutes or seconds, rather than hours or days, allowing for the analysis of truly variable source conditions of much greater resolution than is normally possible when a new simulation must be run for each datapoint in a study. This method has been benchmarked and used to recreate optimization studies in a small fraction of the time spent in the original studies

Emergency Evacuation Simulation for Radiological Emergency; A Case Study of Gijang

Energy Technology Data Exchange (ETDEWEB)

Lee, Gyu M.; Na, Kyoungseok; Jeong, Jae Jun; Ahn, Seokyoung; Park, Seonghee [Pusan National Univ., Busan (Korea, Republic of)

2014-05-15

The recent nuclear reactor accident at Fukushima caused the residents at Gijang to be concerned about the safety of their local nuclear plants. The nuclear reactor-related accidents is very rare but may cause the serious consequences and last for significant period. Especially, Gijang is located next to Busan, at which most population is concentrated. Hence, the effective and efficient emergency evacuation plan cannot be overemphasized in addition to well-designed nuclear disaster prevention measures. The central government has studied the safety issues of nuclear plants and developed the prevention systems. However, the local government also needs their emergency evacuation plan for its residents, considering its geographical and local factors such as various modes of transportations, transportation and shelters systems. The disasters related to nuclear power plants is rare but their influence is considerable. Therefore, while maintaining the safe facilities, the disaster preparedness cannot be overemphasized. An agent-based emergency evacuation simulation tool has been developed and tested for Gijang area.

Simulation Study of Flap Effects on a Commercial Transport Airplane in Upset Conditions

Science.gov (United States)

Cunningham, Kevin; Foster, John V.; Shah, Gautam H.; Stewart, Eric C.; Ventura, Robin N.; Rivers, Robert A.; Wilborn, James E.; Gato, William

2005-01-01

As part of NASA's Aviation Safety and Security Program, a simulation study of a twinjet transport airplane crew training simulation was conducted to address fidelity for upset or loss of control conditions and to study the effect of flap configuration in those regimes. Piloted and desktop simulations were used to compare the baseline crew training simulation model with an enhanced aerodynamic model that was developed for high-angle-of-attack conditions. These studies were conducted with various flap configurations and addressed the approach-to-stall, stall, and post-stall flight regimes. The enhanced simulation model showed that flap configuration had a significant effect on the character of departures that occurred during post-stall flight. Preliminary comparisons with flight test data indicate that the enhanced model is a significant improvement over the baseline. Some of the unrepresentative characteristics that are predicted by the baseline crew training simulation for flight in the post-stall regime have been identified. This paper presents preliminary results of this simulation study and discusses key issues regarding predicted flight dynamics characteristics during extreme upset and loss-of-control flight conditions with different flap configurations.

Buffered Simulation Games for Büchi Automata

Directory of Open Access Journals (Sweden)

Milka Hutagalung

2014-05-01

Full Text Available Simulation relations are an important tool in automata theory because they provide efficiently computable approximations to language inclusion. In recent years, extensions of ordinary simulations have been studied, for instance multi-pebble and multi-letter simulations which yield better approximations and are still polynomial-time computable. In this paper we study the limitations of approximating language inclusion in this way: we introduce a natural extension of multi-letter simulations called buffered simulations. They are based on a simulation game in which the two players share a FIFO buffer of unbounded size. We consider two variants of these buffered games called continuous and look-ahead simulation which differ in how elements can be removed from the FIFO buffer. We show that look-ahead simulation, the simpler one, is already PSPACE-hard, i.e. computationally as hard as language inclusion itself. Continuous simulation is even EXPTIME-hard. We also provide matching upper bounds for solving these games with infinite state spaces.

The influence of headform orientation and flooring systems on impact dynamics during simulated fall-related head impacts.

Science.gov (United States)

Wright, Alexander D; Laing, Andrew C

2012-10-01

Novel compliant flooring systems are a promising approach for reducing fall-related injuries in seniors, as they may provide up to 50% attenuation in peak force during simulated hip impacts while eliciting only minimal influences on balance. This study aimed to determine the protective capacity of novel compliant floors during simulated 'high severity' head impacts compared to common flooring systems. A headform was impacted onto a common Commercial-Carpet at 1.5, 2.5, and 3.5 m/s in front, back, and side orientations using a mechanical drop tower. Peak impact force applied to the headform (F(max)), peak linear acceleration of the headform (g(max)) and Head Injury Criterion (HIC) were determined. For the 3.5 m/s trials, backwards-oriented impacts were associated with the highest F(max) and HIC values (pfloors (Resilient Rubber, Residential-Loop Carpet, Berber Carpet) and six novel compliant floors at each impact velocity. ANOVAs indicated that flooring type was associated with all parameters at each impact velocity (pfloors (pfloors can substantially reduce the forces and accelerations applied to a headform compared to common floors including carpet and resilient rubber. In combination with reports of minimal balance impairments, these findings support the promise of novel compliant floors as a biomechanically effective strategy for reducing fall-related injuries including traumatic brain injuries and skull fractures. Copyright © 2011 IPEM. Published by Elsevier Ltd. All rights reserved.

Physical layer simulation study for the coexistence of WLAN standards

Energy Technology Data Exchange (ETDEWEB)

Howlader, M. K. [Marquette Univ., 222 Haggerty Hall, P. O. Box 1881, Milwaukee, WI 53201 (United States); Keiger, C. [Analysis and Measurement Services Corporation, 9111 Cross Park Drive, Knoxville, TN 37923 (United States); Ewing, P. D. [Oak Ridge National Laboratory, MS-6006, P. O. Box 2008, Oak Ridge, TN 37831 (United States); Govan, T. V. [U.S. Nuclear Regulatory Commission, MS T-10-D20, 11545 Rockville Pike, Rockville, MD 20852 (United States)

2006-07-01

This paper presents the results of a study on the performance of wireless local area network (WLAN) devices in the presence of interference from other wireless devices. To understand the coexistence of these wireless protocols, simplified physical-layer-system models were developed for the Bluetooth, Wireless Fidelity (WiFi), and Zigbee devices, all of which operate within the 2.4-GHz frequency band. The performances of these protocols were evaluated using Monte-Carlo simulations under various interference and channel conditions. The channel models considered were basic additive white Gaussian noise (AWGN), Rayleigh fading, and site-specific fading. The study also incorporated the basic modulation schemes, multiple access techniques, and channel allocations of the three protocols. This research is helping the U.S. Nuclear Regulatory Commission (NRC) understand the coexistence issues associated with deploying wireless devices and could prove useful in the development of a technical basis for guidance to address safety-related issues with the implementation of wireless systems in nuclear facilities. (authors)

Physical layer simulation study for the coexistence of WLAN standards

International Nuclear Information System (INIS)

Howlader, M. K.; Keiger, C.; Ewing, P. D.; Govan, T. V.

2006-01-01

This paper presents the results of a study on the performance of wireless local area network (WLAN) devices in the presence of interference from other wireless devices. To understand the coexistence of these wireless protocols, simplified physical-layer-system models were developed for the Bluetooth, Wireless Fidelity (WiFi), and Zigbee devices, all of which operate within the 2.4-GHz frequency band. The performances of these protocols were evaluated using Monte-Carlo simulations under various interference and channel conditions. The channel models considered were basic additive white Gaussian noise (AWGN), Rayleigh fading, and site-specific fading. The study also incorporated the basic modulation schemes, multiple access techniques, and channel allocations of the three protocols. This research is helping the U.S. Nuclear Regulatory Commission (NRC) understand the coexistence issues associated with deploying wireless devices and could prove useful in the development of a technical basis for guidance to address safety-related issues with the implementation of wireless systems in nuclear facilities. (authors)

Large Scale Simulation Platform for NODES Validation Study

Energy Technology Data Exchange (ETDEWEB)

Sotorrio, P. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Qin, Y. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Min, L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-04-27

This report summarizes the Large Scale (LS) simulation platform created for the Eaton NODES project. The simulation environment consists of both wholesale market simulator and distribution simulator and includes the CAISO wholesale market model and a PG&E footprint of 25-75 feeders to validate the scalability under a scenario of 33% RPS in California with additional 17% of DERS coming from distribution and customers. The simulator can generate hourly unit commitment, 5-minute economic dispatch, and 4-second AGC regulation signals. The simulator is also capable of simulating greater than 10k individual controllable devices. Simulated DERs include water heaters, EVs, residential and light commercial HVAC/buildings, and residential-level battery storage. Feeder-level voltage regulators and capacitor banks are also simulated for feeder-level real and reactive power management and Vol/Var control.

Simulated Leaching (Migration) Study for a Model Container-Closure System Applicable to Parenteral and Ophthalmic Drug Products.

Science.gov (United States)

Jenke, Dennis; Egert, Thomas; Hendricker, Alan; Castner, James; Feinberg, Tom; Houston, Christopher; Hunt, Desmond G; Lynch, Michael; Nicholas, Kumudini; Norwood, Daniel L; Paskiet, Diane; Ruberto, Michael; Smith, Edward J; Holcomb, Frank; Markovic, Ingrid

2017-01-01

A simulating leaching (migration) study was performed on a model container-closure system relevant to parenteral and ophthalmic drug products. This container-closure system consisted of a linear low-density polyethylene bottle (primary container), a polypropylene cap and an elastomeric cap liner (closure), an adhesive label (labeling), and a foil overpouch (secondary container). The bottles were filled with simulating solvents (aqueous salt/acid mixture at pH 2.5, aqueous buffer at pH 9.5, and 1/1 v/v isopropanol/water), a label was affixed to the filled and capped bottles, the filled bottles were placed into the foil overpouch, and the filled and pouched units were stored either upright or inverted for up to 6 months at 40 °C. After storage, the leaching solutions were tested for leached substances using multiple complementary analytical techniques to address volatile, semi-volatile, and non-volatile organic and inorganic extractables as potential leachables.The leaching data generated supported several conclusions, including that (1) the extractables (leachables) profile revealed by a simulating leaching study can qualitatively be correlated with compositional information for materials of construction, (2) the chemical nature of both the extracting medium and the individual extractables (leachables) can markedly affect the resulting profile, and (3) while direct contact between a drug product and a system's material of construction may exacerbate the leaching of substances from that material by the drug product, direct contact is not a prerequisite for migration and leaching to occur. LAY ABSTRACT: The migration of container-related extractables from a model pharmaceutical container-closure system and into simulated drug product solutions was studied, focusing on circumstances relevant to parenteral and ophthalmic drug products. The model system was constructed specifically to address the migration of extractables from labels applied to the outside of the

SU-F-T-682: In-Vivo Simulation of the Relative Biological Effectiveness in Proton Therapy Using a Monte Carlo Method

International Nuclear Information System (INIS)

Oesten, H; Loeck, S; Wohlfahrt, P; Helmbrecht, S; Tillner, F; Schuemann, J; Luehr, A

2016-01-01

Purpose: In proton therapy, the relative biological effectiveness (RBE) – compared with conventional photon therapy – is routinely set to 1.1. However, experimental in vitro studies indicate evidence for the variability of the RBE. To clarify the impact on patient treatment, investigation of the RBE in a preclinical case study should be performed. Methods: The Monte Carlo software TOPAS was used to simulate the radiation field of an irradiation setup at the experimental beamline of the proton therapy facility (OncoRay) in Dresden, Germany. Simulations were performed on cone beam CT-data (CBCT) of a xenogeneous mouse with an orthotopic lung carcinoma obtained by an in-house developed small animal image-guided radiotherapy device. A homogeneous physical fraction dose of 1.8Gy was prescribed for the contoured tumor volume. Simulated dose and linear energy transfer distributions were used to estimate RBE values in the mouse based on an RBE model by Wedenberg et al. To characterize radiation sensitivity of normal and tumor tissue, α/β-ratios were taken from the literature for NB1RGB (10.1Gy) and human squamous lung cancer (6.2Gy) cell lines, respectively. Results: Good dose coverage of the target volume was achieved with a spread-out Bragg peak (SOBP). The contra-lateral lung was completely spared from receiving radiation. An increase in RBE towards the distal end of the SOBP from 1.07 to 1.35 and from 1.05 to 1.3 was observed when considering normal tissue and tumor, respectively, with the highest RBE values located distal to the target volume. Conclusion: Modeled RBE values simulated on CBCT for experimental preclinical proton therapy varied with tissue type and depth in a mouse and differed therefore from a constant value of 1.1. Further translational work will include, first, conducting preclinical experiments and, second, analogous RBE studies in patients using experimentally verified simulation settings for our clinically used patient-specific beam

SU-F-T-682: In-Vivo Simulation of the Relative Biological Effectiveness in Proton Therapy Using a Monte Carlo Method

Energy Technology Data Exchange (ETDEWEB)

Oesten, H [OncoRay - National Center for Radiation Research in Oncology, Faculty of Medicine and University Hospital Carl Gustav Carus, Technische Universitaet Dresden (Germany); Massachusetts General Hospital, Boston, MA (Germany); Loeck, S; Wohlfahrt, P [OncoRay - National Center for Radiation Research in Oncology, Faculty of Medicine and University Hospital Carl Gustav Carus, Technische Universitaet Dresden (Germany); Helmbrecht, S [OncoRay - National Center for Radiation Research in Oncology, Faculty of Medicine and University Hospital Carl Gustav Carus, Technische Universitaet Dresden (Germany); Institute of Radiation Physics, Helmholtz-Zentrum Dresden-Rossendorf (Germany); Tillner, F [OncoRay - National Center for Radiation Research in Oncology, Faculty of Medicine and University Hospital Carl Gustav Carus, Technische Universitaet Dresden (Germany); Department of Radiation Oncology, University Hospital Carl Gustav Carus, Technische Universitaet Dresden (Germany); Schuemann, J [Massachusetts General Hospital, Boston, MA (United States); Luehr, A [OncoRay - National Center for Radiation Research in Oncology, Faculty of Medicine and University Hospital Carl Gustav Carus, Technische Universitaet Dresden (Germany); German Cancer Consortium (DKTK), Dresden (Germany); German Cancer Research Center (DKFZ), Heidelberg (Germany)

2016-06-15

Purpose: In proton therapy, the relative biological effectiveness (RBE) – compared with conventional photon therapy – is routinely set to 1.1. However, experimental in vitro studies indicate evidence for the variability of the RBE. To clarify the impact on patient treatment, investigation of the RBE in a preclinical case study should be performed. Methods: The Monte Carlo software TOPAS was used to simulate the radiation field of an irradiation setup at the experimental beamline of the proton therapy facility (OncoRay) in Dresden, Germany. Simulations were performed on cone beam CT-data (CBCT) of a xenogeneous mouse with an orthotopic lung carcinoma obtained by an in-house developed small animal image-guided radiotherapy device. A homogeneous physical fraction dose of 1.8Gy was prescribed for the contoured tumor volume. Simulated dose and linear energy transfer distributions were used to estimate RBE values in the mouse based on an RBE model by Wedenberg et al. To characterize radiation sensitivity of normal and tumor tissue, α/β-ratios were taken from the literature for NB1RGB (10.1Gy) and human squamous lung cancer (6.2Gy) cell lines, respectively. Results: Good dose coverage of the target volume was achieved with a spread-out Bragg peak (SOBP). The contra-lateral lung was completely spared from receiving radiation. An increase in RBE towards the distal end of the SOBP from 1.07 to 1.35 and from 1.05 to 1.3 was observed when considering normal tissue and tumor, respectively, with the highest RBE values located distal to the target volume. Conclusion: Modeled RBE values simulated on CBCT for experimental preclinical proton therapy varied with tissue type and depth in a mouse and differed therefore from a constant value of 1.1. Further translational work will include, first, conducting preclinical experiments and, second, analogous RBE studies in patients using experimentally verified simulation settings for our clinically used patient-specific beam

Study of numerical simulations concerning the performance of antennas used for automobile wireless communications; Jidosha no musen tsushin ni okeru antenna seino hyoka no tame no suchi simulation no ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Sueyoshi, M; Yano, T; Noda, Y; Goto, H [Honda Lock Mfg. Co. Ltd., Tokyo (Japan)

1997-10-01

Automobiles and communication technologies will be more closely related with each other in the advanced intelligence society. Anti-theft security systems apply those technologies, where antenna performance is one of the key elements. This is a study of numerical simulations of the performance of those vehicle antennas. 2 refs., 2 figs.

Realization of a simulator for radon-222 underground migration studies

International Nuclear Information System (INIS)

Tidjani, A.; Seidel, J.L.; Monnin, M.; Isabelle, D.B.

1987-01-01

To study under controlled conditions the underground movements of radon gas a simulator has been built. It was designed in order to vary independently the different geophysical parameters such as pressure, temperature, humidity, type of soil and its granulometry, etc.. The first tests, described in this paper, have demonstrated the usefullness of such a simulator. (orig.)

A comparative study of defibrillation and cardiopulmonary resuscitation performance during simulated cardiac arrest in nursing student teams

Directory of Open Access Journals (Sweden)

Eikeland Husebø Sissel I

2012-04-01

Full Text Available Abstract Background Although nurses must be able to respond quickly and effectively to cardiac arrest, numerous studies have demonstrated poor performance. Simulation is a promising learning tool for resuscitation team training but there are few studies that examine simulation for training defibrillation and cardiopulmonary resuscitation (D-CPR in teams from the nursing education perspective. The aim of this study was to investigate the extent to which nursing student teams follow the D-CPR-algorithm in a simulated cardiac arrest, and if observing a simulated cardiac arrest scenario and participating in the post simulation debriefing would improve team performance. Methods We studied video-recorded simulations of D-CPR performance in 28 nursing student teams. Besides describing the overall performance of D-CPR, we compared D-CPR performance in two groups. Group A (n = 14 performed D-CPR in a simulated cardiac arrest scenario, while Group B (n = 14 performed D-CPR after first observing performance of Group A and participating in the debriefing. We developed a D-CPR checklist to assess team performance. Results Overall there were large variations in how accurately the nursing student teams performed the specific parts of the D-CPR algorithm. While few teams performed opening the airways and examination of breathing correctly, all teams used a 30:2 compression: ventilation ratio. We found no difference between Group A and Group B in D-CPR performance, either in regard to total points on the check list or to time variables. Conclusion We found that none of the nursing student teams achieved top scores on the D-CPR-checklist. Observing the training of other teams did not increase subsequent performance. We think all this indicates that more time must be assigned for repetitive practice and reflection. Moreover, the most important aspects of D-CPR, such as early defibrillation and hands-off time in relation to shock, must be highlighted in team

The impact of therapeutic opioid agonists on driving-related psychomotor skills assessed by a driving simulator or an on-road driving task: A systematic review.

Science.gov (United States)

Ferreira, Diana H; Boland, Jason W; Phillips, Jane L; Lam, Lawrence; Currow, David C

2018-04-01

Driving cessation is associated with poor health-related outcomes. People with chronic diseases are often prescribed long-term opioid agonists that have the potential to impair driving. Studies evaluating the impact of opioids on driving-related psychomotor skills report contradictory results likely due to heterogeneous designs, assessment tools and study populations. A better understanding of the effects of regular therapeutic opioid agonists on driving can help to inform the balance between individual's independence and community safety. To identify the literature assessing the impact of regular therapeutic opioid agonists on driving-related psychomotor skills for people with chronic pain or chronic breathlessness. Systematic review reported in accordance with the Preferred Reporting Items for Systematic Review and Meta-analysis statement; PROSPERO Registration CRD42017055909. Six electronic databases and grey literature were systematically searched up to January, 2017. Inclusion criteria were as follows: (1) empirical studies reporting data on driving simulation, on-the-road driving tasks or driving outcomes; (2) people with chronic pain or chronic breathlessness; and (3) taking regular therapeutic opioid agonists. Critical appraisal used the National Institutes of Health's quality assessment tools. From 3809 records screened, three studies matched the inclusion criteria. All reported data on people with chronic non-malignant pain. No significant impact of regular therapeutic opioid agonists on people's driving-related psychomotor skills was reported. One study reported more intense pain significantly worsened driving performance. This systematic review does not identify impaired simulated driving performance when people take regular therapeutic opioid agonists for symptom control, although more prospective studies are needed.

Nuclear power plant diagnostics study at the Midland training simulator

International Nuclear Information System (INIS)

Reifman, J.; Rank, P.; Lee, J.C.

1991-01-01

Training simulators provide a real world environment for testing advanced diagnostic and control systems as an aid to nuclear power plant operators. The simulators not only duplicate the hardware din the actual control room, allowing for analysis of man-machine interface, but also represent the dynamic behavior of the reference plant in real-time, in a realistic manner. Training simulators provide the means to representing the reference plant operations in a wide range of operation conditions including off-normal and emergency conditions. Transient events with very low probability of occurrence can then be represented and used to test the capabilities of advanced diagnostic and control systems. For these reasons, full-scope operator training simulators have been used as a test bed for a number of advanced diagnostic concepts. The University of Michigan and Consumers Power Company have been collaborating in a program devoted to the development and study of advanced concepts for automatic diagnostics and control of nuclear power plants. The program has been focused on the use of the full-scope operator training Midland Nuclear Power Plant Unit 2 (MNP-2) Simulator for development, testing, and verification of advanced diagnostics concepts. In their current efforts, the authors have developed two artificial intelligent (AI) diagnostic concepts that have been applied to the MNP-2 Simulator: the systematic generation and updating of a rule-based knowledge system for nuclear power plant diagnostics and a nonlinear parameter estimation algorithm called the simulation filter. The simulation filter algorithm is used with the MNP-2 Simulator to improve the simulation of the Three Mile Island Unit 2 (TMI-2) accident. 11 refs., 4 figs

Reminiscence of CFD simulation; CFD simulation no omoide

Energy Technology Data Exchange (ETDEWEB)

Shimamoto, Y. [University of Shiga Prefecture, Shiga (Japan)

1998-12-01

Upon graduation from university, the author began studying internal combustion engines, and has been engaged in the numerical analysis of gas flows for 45 years. His graduation study involved the measurement of velocity distribution at the turbine nozzle outlet in the subsonic domain. When he was in the internal engine laboratory of the graduate school, Mentor Fujio Nagao presented him with an essay of E. Jenny on the characteristic curve method, that is, a writing on the numerical analysis of gas flows in the exhaust system of a pulse operation engine. From that time onward, he has been involved with numerical simulation in this field. Some seniors of his gave him various advice about his way too much inclined toward numerical calculation. But the author believes that, as far as one is interested in numerical analysis and does not refrain from touching things, new discoveries related to engineering will occur at the same probability, whether one is absorbed in experiment or in simulation. In the study of simulation, although the engineers concerned are supposed to make propositions on practical programs for prediction that may be applicable to various fields well as to seek for new schemes, it is desired that cooperative studies between industries and universities will become real that are open to the public. (NEDO)

Towards a complex systems approach in sports injury research: simulating running-related injury development with agent-based modelling.

Science.gov (United States)

Hulme, Adam; Thompson, Jason; Nielsen, Rasmus Oestergaard; Read, Gemma J M; Salmon, Paul M

2018-06-18

There have been recent calls for the application of the complex systems approach in sports injury research. However, beyond theoretical description and static models of complexity, little progress has been made towards formalising this approach in way that is practical to sports injury scientists and clinicians. Therefore, our objective was to use a computational modelling method and develop a dynamic simulation in sports injury research. Agent-based modelling (ABM) was used to model the occurrence of sports injury in a synthetic athlete population. The ABM was developed based on sports injury causal frameworks and was applied in the context of distance running-related injury (RRI). Using the acute:chronic workload ratio (ACWR), we simulated the dynamic relationship between changes in weekly running distance and RRI through the manipulation of various 'athlete management tools'. The findings confirmed that building weekly running distances over time, even within the reported ACWR 'sweet spot', will eventually result in RRI as athletes reach and surpass their individual physical workload limits. Introducing training-related error into the simulation and the modelling of a 'hard ceiling' dynamic resulted in a higher RRI incidence proportion across the population at higher absolute workloads. The presented simulation offers a practical starting point to further apply more sophisticated computational models that can account for the complex nature of sports injury aetiology. Alongside traditional forms of scientific inquiry, the use of ABM and other simulation-based techniques could be considered as a complementary and alternative methodological approach in sports injury research. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Glass polymorphism in glycerol–water mixtures: I. A computer simulation study

Science.gov (United States)

Jahn, David A.; Wong, Jessina; Bachler, Johannes; Loerting, Thomas

2016-01-01

We perform out-of-equilibrium molecular dynamics (MD) simulations of water–glycerol mixtures in the glass state. Specifically, we study the transformations between low-density (LDA) and high-density amorphous (HDA) forms of these mixtures induced by compression/decompression at constant temperature. Our MD simulations reproduce qualitatively the density changes observed in experiments. Specifically, the LDA–HDA transformation becomes (i) smoother and (ii) the hysteresis in a compression/decompression cycle decreases as T and/or glycerol content increase. This is surprising given the fast compression/decompression rates (relative to experiments) accessible in MD simulations. We study mixtures with glycerol molar concentration χ g = 0–13% and find that, for the present mixture models and rates, the LDA–HDA transformation is detectable up to χ g ≈ 5%. As the concentration increases, the density of the starting glass (i.e., LDA at approximately χ g ≤ 5%) rapidly increases while, instead, the density of HDA remains practically constant. Accordingly, the LDA state and hence glass polymorphism become inaccessible for glassy mixtures with approximately χ g > 5%. We present an analysis of the molecular-level changes underlying the LDA–HDA transformation. As observed in pure glassy water, during the LDA-to-HDA transformation, water molecules within the mixture approach each other, moving from the second to the first hydration shell and filling the first interstitial shell of water molecules. Interestingly, similar changes also occur around glycerol OH groups. It follows that glycerol OH groups contribute to the density increase during the LDA–HDA transformation. An analysis of the hydrogen bond (HB)-network of the mixtures shows that the LDA–HDA transformation is accompanied by minor changes in the number of HBs of water and glycerol. Instead, large changes in glycerol and water coordination numbers occur. We also perform a detailed analysis of the

Virtual reality simulators for rock engineering related training.

CSIR Research Space (South Africa)

Squelch, A

1997-12-01

Full Text Available Virtual reality (VR) has been investigated by SIMRAC and CSIR Miningtek as a means of providing an enhancement to current training methods that will lead to more effective hazard awareness training programmes. A VR training simulator developed under...

One-dimensional plasma simulation studies

International Nuclear Information System (INIS)

Friberg, Ari; Virtamo, Jorma

1976-01-01

Some basic plasma phenomena are studied by a one-dimensional electrostatic simulation code. A brief description of the code and its application to a test problem is given. The experiments carried out include Landau damping of an excited wave, particle retardation by smoothed field and beam-plasma instability. In each case, the set-up of the experiment is described and the results are compared with theoretical predictions. In the theoretical discussions, the oscillatory behaviour found in the Landau damping experiment is explained, an explicit formula for the particle retardation rate is derived and a rudimentary picture of the beam-plasma instability in terms of quasilinear theory is given. (author)

Modeling and Simulation Optimization and Feasibility Studies for the Neutron Detection without Helium-3 Project

Energy Technology Data Exchange (ETDEWEB)

Ely, James H.; Siciliano, Edward R.; Swinhoe, Martyn T.; Lintereur, Azaree T.

2013-01-01

This report details the results of the modeling and simulation work accomplished for the ‘Neutron Detection without Helium-3’ project during the 2011 and 2012 fiscal years. The primary focus of the project is to investigate commercially available technologies that might be used in safeguards applications in the relatively near term. Other technologies that are being developed may be more applicable in the future, but are outside the scope of this study.

The neural basis of event simulation: an FMRI study.

Directory of Open Access Journals (Sweden)

Yukihito Yomogida

Full Text Available Event simulation (ES is the situational inference process in which perceived event features such as objects, agents, and actions are associated in the brain to represent the whole situation. ES provides a common basis for various cognitive processes, such as perceptual prediction, situational understanding/prediction, and social cognition (such as mentalizing/trait inference. Here, functional magnetic resonance imaging was used to elucidate the neural substrates underlying important subdivisions within ES. First, the study investigated whether ES depends on different neural substrates when it is conducted explicitly and implicitly. Second, the existence of neural substrates specific to the future-prediction component of ES was assessed. Subjects were shown contextually related object pictures implying a situation and performed several picture-word-matching tasks. By varying task goals, subjects were made to infer the implied situation implicitly/explicitly or predict the future consequence of that situation. The results indicate that, whereas implicit ES activated the lateral prefrontal cortex and medial/lateral parietal cortex, explicit ES activated the medial prefrontal cortex, posterior cingulate cortex, and medial/lateral temporal cortex. Additionally, the left temporoparietal junction plays an important role in the future-prediction component of ES. These findings enrich our understanding of the neural substrates of the implicit/explicit/predictive aspects of ES-related cognitive processes.

Post-processing of Monte Carlo simulations for rapid BNCT source optimization studies

International Nuclear Information System (INIS)

Bleuel, D.L.; Chu, W.T.; Donahue, R.J.; Ludewigt, B.A.; Vujic, J.

2000-01-01

A great advantage of some neutron sources, such as accelerator-produced sources, is that they can be tuned to produce different spectra. Unfortunately, optimization studies are often time-consuming and difficult, as they require a lengthy Monte Carlo simulation for each source. When multiple characteristics, such as energy, angle, and spatial distribution of a neutron beam are allowed to vary, an overwhelming number of simulations may be required. Many optimization studies, therefore, suffer from a small number of data points, restrictive treatment conditions, or poor statistics. By scoring pertinent information from every particle tally in a Monte Carlo simulation, then applying appropriate source variable weight factors in a post-processing algorithm; a single simulation can be used to model any number of multiple sources. Through this method, the response to a new source can be modeled in minutes or seconds, rather than hours or days, allowing for the analysis of truly variable source conditions of much greater resolution than is normally possible when a new simulation must be run for each data point in a study. This method has been benchmarked and used to recreate optimization studies in a small fraction of the time spent in the original studies. (author)

Virtual Gaming Simulation in Nursing Education: A Focus Group Study.

Science.gov (United States)

Verkuyl, Margaret; Hughes, Michelle; Tsui, Joyce; Betts, Lorraine; St-Amant, Oona; Lapum, Jennifer L

2017-05-01

The use of serious gaming in a virtual world is a novel pedagogical approach in nursing education. A virtual gaming simulation was implemented in a health assessment class that focused on mental health and interpersonal violence. The study's purpose was to explore students' experiences of the virtual gaming simulation. Three focus groups were conducted with a convenience sample of 20 first-year nursing students after they completed the virtual gaming simulation. Analysis yielded five themes: (a) Experiential Learning, (b) The Learning Process, (c) Personal Versus Professional, (d) Self-Efficacy, and (e) Knowledge. Virtual gaming simulation can provide experiential learning opportunities that promote engagement and allow learners to acquire and apply new knowledge while practicing skills in a safe and realistic environment. [J Nurs Educ. 2017;56(5):274-280.]. Copyright 2017, SLACK Incorporated.

RTS amplitudes in decananometer MOSFETs: 3-D simulation study

OpenAIRE

Asenov, A.; Balasubramaniam, R.; Brown, A.R.; Davies, J.H.

2003-01-01

In this paper we study the amplitudes of random telegraph signals (RTS) associated with the trapping of a single electron in defect states at the Si/SiO/sub 2/ interface of sub-100-nm (decananometer) MOSFETs employing three-dimensional (3-D) "atomistic" simulations. Both continuous doping charge and random discrete dopants in the active region of the MOSFETs are considered in the simulations. The dependence of the RTS amplitudes on the position of the trapped charge in the channel and on devi...

Monte Carlo simulation of a four-layer DOI detector with relative offset in animal PET

International Nuclear Information System (INIS)

Chung, Yong Hyun; Hwang, Ji Yeon; Baek, Cheol-Ha; Lee, Seung-Jae; Ito, Mikiko; Lee, Jae Sung; Hong, Seong Jong

2011-01-01

We have built a four-layer detector to obtain depth of interaction (DOI) information in which all four layers have a relative offset of half a crystal pitch with each other. The main characteristics of the detector, especially the energy and spatial resolutions, strongly depend on the crystal surface treatments. As a part of the development of an animal PET, we have investigated the effect of crystal surface treatment on detector performances using Monte Carlo simulations in order to optimize the surface conditions of crystals composing a four-layer detector. The proposed detector consists of four LYSO layers with crystal dimensions of 1.5x1.5x7.0 and 1.5x1.5x5.0 mm 3 . A simulation tool (DETECT2000) was used and validated against the experimental results; flood images were acquired by a prototype module. Flood images were simulated by varying the surface treatment of the crystals. The optimal surface conditions of the four-layer crystals were derived for a small animal PET with a view towards achieving high sensitivity, as well as high and uniform radial resolution.

A simulation study on garment manufacturing process

Science.gov (United States)

Liong, Choong-Yeun; Rahim, Nur Azreen Abdul

2015-02-01

Garment industry is an important industry and continues to evolve in order to meet the consumers' high demands. Therefore, elements of innovation and improvement are important. In this work, research studies were conducted at a local company in order to model the sewing process of clothes manufacturing by using simulation modeling. Clothes manufacturing at the company involves 14 main processes, which are connecting the pattern, center sewing and side neating, pockets sewing, backside-sewing, attaching the front and back, sleeves preparation, attaching the sleeves and over lock, collar preparation, collar sewing, bottomedge sewing, buttonholing sewing, removing excess thread, marking button, and button cross sewing. Those fourteen processes are operated by six tailors only. The last four sets of processes are done by a single tailor. Data collection was conducted by on site observation and the probability distribution of processing time for each of the processes is determined by using @Risk's Bestfit. Then a simulation model is developed using Arena Software based on the data collected. Animated simulation model is developed in order to facilitate understanding and verifying that the model represents the actual system. With such model, what if analysis and different scenarios of operations can be experimented with virtually. The animation and improvement models will be presented in further work.

Cultures of simulations vs. cultures of calculations? The development of simulation practices in meteorology and astrophysics

Science.gov (United States)

Sundberg, Mikaela

While the distinction between theory and experiment is often used to discuss the place of simulation from a philosophical viewpoint, other distinctions are possible from a sociological perspective. Turkle (1995) distinguishes between cultures of calculation and cultures of simulation and relates these cultures to the distinction between modernity and postmodernity, respectively. What can we understand about contemporary simulation practices in science by looking at them from the point of view of these two computer cultures? What new questions does such an analysis raise for further studies? On the basis of two case studies, the present paper compares and discusses simulation activities in astrophysics and meteorology. It argues that simulation practices manifest aspects of both of these cultures simultaneously, but in different situations. By employing the dichotomies surface/depth, play/seriousness, and extreme/reasonable to characterize and operationalize cultures of calculation and cultures of simulation as sensitizing concepts, the analysis shows how simulation code work shifts from development to use, the importance of but also resistance towards too much visualizations, and how simulation modelers play with extreme values, yet also try to achieve reasonable results compared to observations.

Molecular dynamics simulation studies of tailored nanostructured polymers

Science.gov (United States)

Liu, Lixin

With recent advancements in the synthesis and characterization of polymeric materials, scientists are able to create multi-scale novel polymers with various cases of chemical functionalities, diversified topologies, as well as cross-linking networks. Due to those remarkable achievements, there are a broad range of possible applications of smart polymers in catalysis, in environmental remediation, and especially in drug-delivery. Because of rising interest in developing therapeutic drug binding to specific treating target, polymer chemists are in particular interests in design and engineering the drug delivery materials to be not only bio-compatible, but also to be capable of self-assembly at various in-vivo physiological stimulus. Both experimental and theoretical work indicate that the thermodynamic properties relating to the hydrophobic effect play an important role in determining self-assembly process. At the same time, computational simulation and modeling are powerful instruments to contribute to microscopic thermodynamics' understanding toward self-assembly phenomenon. Along with statistical approaches, constructing empirical model based on simulation results would also help predict for further development of tailored nano-structured materials. My Research mainly focused on investigating physical and chemical characteristics of polymer materials through molecular dynamics simulation and probing the fundamental thermodynamic driving force of self-assembly behavior. We tried to surmount technological obstacles in computational chemistry and build an efficient scheme to identify the physical and chemical Feature of molecules, to reproduce underlying properties, to understand the origin of thermodynamic signatures, and to speed up current trial and error process in screening new materials.

Comparative study of the effectiveness of three learning environments: Hyper-realistic virtual simulations, traditional schematic simulations and traditional laboratory

Directory of Open Access Journals (Sweden)

Maria Isabel Suero

2011-10-01

Full Text Available This study compared the educational effects of computer simulations developed in a hyper-realistic virtual environment with the educational effects of either traditional schematic simulations or a traditional optics laboratory. The virtual environment was constructed on the basis of Java applets complemented with a photorealistic visual output. This new virtual environment concept, which we call hyper-realistic, transcends basic schematic simulation; it provides the user with a more realistic perception of a physical phenomenon being simulated. We compared the learning achievements of three equivalent, homogeneous groups of undergraduates—an experimental group who used only the hyper-realistic virtual laboratory, a first control group who used a schematic simulation, and a second control group who used the traditional laboratory. The three groups received the same theoretical preparation and carried out equivalent practicals in their respective learning environments. The topic chosen for the experiment was optical aberrations. An analysis of variance applied to the data of the study demonstrated a statistically significant difference (p value <0.05 between the three groups. The learning achievements attained by the group using the hyper-realistic virtual environment were 6.1 percentage points higher than those for the group using the traditional schematic simulations and 9.5 percentage points higher than those for the group using the traditional laboratory.

Gelled fuel simulant

International Nuclear Information System (INIS)

Christy, J.; Hiser, E.J.; Sippel, N.J.

1980-01-01

A relatively stable inert simulant formulation for a hazardous metallized fuel has the density, shear rate and yield stress of the duplicated fuel. This formulation provides inexpensive and safe testing of exploratory hydraulic studies, or testing of the mechanical strength of containers, plumbing, etc., in which the metallized fuels are to be used

Simulation models: a current indispensable tool in studies of the continuous water-soil-plant - atmosphere

International Nuclear Information System (INIS)

Lopez Seijas, Teresa; Gonzalez, Felicita; Cid, G.; Osorio, Maria de los A.; Ruiz, Maria Elena

2008-01-01

Full text: This work assesses the current use of simulation models as a tool useful and indispensable for the advancement in the research and study of the processes related to the continuous water-soil - plant-atmosphere. In recent years they have reported in the literature many jobs where these modeling tools are used as a support to the decision-making process of companies or organizations in the agricultural sphere and in Special for the design of optimal management of irrigation and fertilization strategies of the crops. Summarizes some of the latest applications reported with respect to the use of water transfers and solutes, such simulation models mainly to nitrate leaching and groundwater contamination problems. On the other hand also summarizes important applications of simulation models of growth of cultivation for the prediction of effects on the performance of different conditions of water stress, and finally some other applications on the management of the different irrigation technologies as kingpins, superfiail irrigation and drip irrigation. Refer also the main work carried out in Cuba. (author)

Comparison of meaningful learning characteristics in simulated nursing practice after traditional versus computer-based simulation method: a qualitative videography study.

Science.gov (United States)

Poikela, Paula; Ruokamo, Heli; Teräs, Marianne

2015-02-01

Nursing educators must ensure that nursing students acquire the necessary competencies; finding the most purposeful teaching methods and encouraging learning through meaningful learning opportunities is necessary to meet this goal. We investigated student learning in a simulated nursing practice using videography. The purpose of this paper is to examine how two different teaching methods presented students' meaningful learning in a simulated nursing experience. The 6-hour study was divided into three parts: part I, general information; part II, training; and part III, simulated nursing practice. Part II was delivered by two different methods: a computer-based simulation and a lecture. The study was carried out in the simulated nursing practice in two universities of applied sciences, in Northern Finland. The participants in parts II and I were 40 first year nursing students; 12 student volunteers continued to part III. Qualitative analysis method was used. The data were collected using video recordings and analyzed by videography. The students who used a computer-based simulation program were more likely to report meaningful learning themes than those who were first exposed to lecture method. Educators should be encouraged to use computer-based simulation teaching in conjunction with other teaching methods to ensure that nursing students are able to receive the greatest educational benefits. Copyright © 2014 Elsevier Ltd. All rights reserved.

Online external beam radiation treatment simulator

International Nuclear Information System (INIS)

Hamza-Lup, Felix G.; Sopin, Ivan; Zeidan, Omar

2008-01-01

Radiation therapy is an effective and widely accepted form of treatment for many types of cancer that requires extensive computerized planning. Unfortunately, current treatment planning systems have limited or no visual aid that combines patient volumetric models extracted from patient-specific CT data with the treatment device geometry in a 3D interactive simulation. We illustrate the potential of 3D simulation in radiation therapy with a web-based interactive system that combines novel standards and technologies. We discuss related research efforts in this area and present in detail several components of the simulator. An objective assessment of the accuracy of the simulator and a usability study prove the potential of such a system for simulation and training. (orig.)

Impact of atmospheric model resolution on simulation of ENSO feedback processes: a coupled model study

Science.gov (United States)

Hua, Lijuan; Chen, Lin; Rong, Xinyao; Su, Jingzhi; Wang, Lu; Li, Tim; Yu, Yongqiang

2018-03-01

This study examines El Niño-Southern Oscillation (ENSO)-related air-sea feedback processes in a coupled general circulation model (CGCM) to gauge model errors and pin down their sources in ENSO simulation. Three horizontal resolutions of the atmospheric component (T42, T63 and T106) of the CGCM are used to investigate how the simulated ENSO behaviors are affected by the resolution. We find that air-sea feedback processes in the three experiments mainly differ in terms of both thermodynamic and dynamic feedbacks. We also find that these processes are simulated more reasonably in the highest resolution version than in the other two lower resolution versions. The difference in the thermodynamic feedback arises from the difference in the shortwave-radiation (SW) feedback. Due to the severely (mildly) excessive cold tongue in the lower (higher) resolution version, the SW feedback is severely (mildly) underestimated. The main difference in the dynamic feedback processes lies in the thermocline feedback and the zonal-advection feedback, both of which are caused by the difference in the anomalous thermocline response to anomalous zonal wind stress. The difference in representing the anomalous thermocline response is attributed to the difference in meridional structure of zonal wind stress anomaly in the three simulations, which is linked to meridional resolution.

The study, design and simulation of a free piston Stirling engine linear alternatorThe study, design and simulation of a free piston Stirling engine linear alternator

Directory of Open Access Journals (Sweden)

Teodora Susana Oros

2014-12-01

Full Text Available This paper presents a study, design and simulation of a Free Piston Stirling Engine Linear Alternator. There are presented the main steps of the magnetic and electric calculations for a permanent magnet linear alternator of fixed coil and moving magnets type. Finally, a detailed thermal, mechanical and electrical model for a Stirling engine linear alternator have been made in SIMULINK simulation program. The linear alternator simulation model uses a controllable DC voltage which simulates the linear alternator combined with a rectifier, a variable load and a DC-DC converter, which compensates for the variable nature of Stirling engine operation, and ensures a constant voltage output regardless of the load.

Driving error and anxiety related to iPod mp3 player use in a simulated driving experience.

Science.gov (United States)

Harvey, Ashley R; Carden, Randy L

2009-08-01

Driver distraction due to cellular phone usage has repeatedly been shown to increase the risk of vehicular accidents; however, the literature regarding the use of other personal electronic devices while driving is relatively sparse. It was hypothesized that the usage of an mp3 player would result in an increase in not only driving error while operating a driving simulator, but driver anxiety scores as well. It was also hypothesized that anxiety scores would be positively related to driving errors when using an mp3 player. 32 participants drove through a set course in a driving simulator twice, once with and once without an iPod mp3 player, with the order counterbalanced. Number of driving errors per course, such as leaving the road, impacts with stationary objects, loss of vehicular control, etc., and anxiety were significantly higher when an iPod was in use. Anxiety scores were unrelated to number of driving errors.

Comparative Study of the Effectiveness of Three Learning Environments: Hyper-Realistic Virtual Simulations, Traditional Schematic Simulations and Traditional Laboratory

Science.gov (United States)

Martinez, Guadalupe; Naranjo, Francisco L.; Perez, Angel L.; Suero, Maria Isabel; Pardo, Pedro J.

2011-01-01

This study compared the educational effects of computer simulations developed in a hyper-realistic virtual environment with the educational effects of either traditional schematic simulations or a traditional optics laboratory. The virtual environment was constructed on the basis of Java applets complemented with a photorealistic visual output.…

Equipment and performance upgrade of compact nuclear simulator

International Nuclear Information System (INIS)

Park, J. C.; Kwon, K. C.; Lee, D. Y.; Hwang, I. K.; Park, W. M.; Cha, K. H.; Song, S. J.; Lee, J. W.; Kim, B. G.; Kim, H. J.

1999-01-01

The simulator at Nuclear Training Center in KAERI became old and has not been used effectively for nuclear-related training and researches due to the problems such as aging of the equipment, difficulties in obtaining consumables and their high cost, and less personnel available who can handle the old equipment. To solve the problems, this study was performed for recovering the functions of the simulator through the technical design and replacement of components with new ones. As results of this study, our test after the replacement showed the same simulation status as the previous one, and new graphic displays added to the simulator was effective for the training and easy for maintenance. This study is meaningful as demonstrating the way of upgrading nuclear training simulators that lost their functioning due to the obsolescence of simulators and the unavailability of components

Pilot-model analysis and simulation study of effect of control task desired control response

Science.gov (United States)

Adams, J. J.; Gera, J.; Jaudon, J. B.

1978-01-01

A pilot model analysis was performed that relates pilot control compensation, pilot aircraft system response, and aircraft response characteristics for longitudinal control. The results show that a higher aircraft short period frequency is required to achieve superior pilot aircraft system response in an altitude control task than is required in an attitude control task. These results were confirmed by a simulation study of target tracking. It was concluded that the pilot model analysis provides a theoretical basis for determining the effect of control task on pilot opinions.

Simulation of a spintronic transistor: A study of its performance

International Nuclear Information System (INIS)

Pela, R.R.; Teles, L.K.

2009-01-01

We study theoretically the magnetic bipolar transistor, and compare its performance with common bipolar transistor. We present not only the simulation results for the characteristic curves, but also other relevant parameters related with its performance, such as: the current amplification factor, the open-loop gain, the hybrid parameters and the cutoff frequency. We noted that the spin-charge coupling introduces new phenomena that enrich the functionality characteristics of the magnetic bipolar transistor. Among other things, it has an adjustable band structure, which may be modified during the device operation; it exhibits the already known spin-voltaic effect. On the other hand, we observed that it is necessary a large g-factor to analyze the influence of the field B over the transistor. Nevertheless, we consider the magnetic bipolar transistor as a promising device for spintronic applications

Simulating secondary organic aerosol from missing diesel-related intermediate-volatility organic compound emissions during the Clean Air for London (ClearfLo campaign

Directory of Open Access Journals (Sweden)

R. Ots

2016-05-01

Full Text Available We present high-resolution (5 km  ×  5 km atmospheric chemical transport model (ACTM simulations of the impact of newly estimated traffic-related emissions on secondary organic aerosol (SOA formation over the UK for 2012. Our simulations include additional diesel-related intermediate-volatility organic compound (IVOC emissions derived directly from comprehensive field measurements at an urban background site in London during the 2012 Clean Air for London (ClearfLo campaign. Our IVOC emissions are added proportionally to VOC emissions, as opposed to proportionally to primary organic aerosol (POA as has been done by previous ACTM studies seeking to simulate the effects of these missing emissions. Modelled concentrations are evaluated against hourly and daily measurements of organic aerosol (OA components derived from aerosol mass spectrometer (AMS measurements also made during the ClearfLo campaign at three sites in the London area. According to the model simulations, diesel-related IVOCs can explain on average  ∼  30 % of the annual SOA in and around London. Furthermore, the 90th percentile of modelled daily SOA concentrations for the whole year is 3.8 µg m−3, constituting a notable addition to total particulate matter. More measurements of these precursors (currently not included in official emissions inventories is recommended. During the period of concurrent measurements, SOA concentrations at the Detling rural background location east of London were greater than at the central London location. The model shows that this was caused by an intense pollution plume with a strong gradient of imported SOA passing over the rural location. This demonstrates the value of modelling for supporting the interpretation of measurements taken at different sites or for short durations.

Dynamics of biopolymers on nanomaterials studied by quasielastic neutron scattering and MD simulations

Science.gov (United States)

Dhindsa, Gurpreet K.

Neutron scattering has been proved to be a powerful tool to study the dynamics of biological systems under various conditions. This thesis intends to utilize neutron scattering techniques, combining with MD simulations, to develop fundamental understanding of several biologically interesting systems. Our systems include a drug delivery system containing Nanodiamonds with nucleic acid (RNA), and two specific model proteins, beta-Casein and Inorganic Pyrophosphatase (IPPase). RNA and nanodiamond (ND) both are suitable for drug-delivery applications in nano-biotechnology. The architecturally flexible RNA with catalytic functionality forms nanocomposites that can treat life-threatening diseases. The non-toxic ND has excellent mechanical and optical properties and functionalizable high surface area, and thus actively considered for biomedical applications. In this thesis, we utilized two tools, quasielastic neutron scattering (QENS) and Molecular Dynamics Simulations to probe the effect of ND on RNA dynamics. Our work provides fundamental understanding of how hydrated RNA motions are affected in the RNA-ND nanocomposites. From the experimental and Molecular Dynamics Simulation (MD), we found that hydrated RNA motion is faster on ND surface than a freestanding one. MD Simulation results showed that the failure of Stokes Einstein relation results the presence of dynamic heterogeneities in the biomacromolecules. Radial pair distribution function from MD Simulation confirmed that the hydrophilic nature of ND attracts more water than RNA results the de-confinement of RNA on ND. Therefore, RNA exhibits faster motion in the presence of ND than freestanding RNA. In the second project, we studied the dynamics of a natively disordered protein beta-Casein which lacks secondary structures. In this study, the temperature and hydration effects on the dynamics of beta-Casein are explored by Quasielastic Neutron Scattering (QENS). We investigated the mean square displacement (MSD) of

Study, simulation and design of a 3D clinostat

Science.gov (United States)

Pavone, Valentina; Guarnieri, Vincenzo; Lobascio, Cesare; Soma, Aurelio; Bosso, Nicola; Lamantea, Matteo Maria

High cost and limited number of physically executable experiments in space have introduced the need for ground simulation systems that enable preparing experiments to be carried out on board, identifying phenomena associated with the altered gravity conditions, and taking advantage of these conditions, as in Biotechnology. Among systems developed to simulate microgravity, especially for life sciences experiments, different types of clinostats were realized. This work deals with mechanical design of a three-dimensional clinostat and simulation of the dynamic behavior of the system by varying the operating parameters. The design and simulation phase was preceded by a careful analysis of the state of art and by the review of the most recent results, in particular from the major investigators of Life Sciences in Space. The mechanical design is quite innovative by adoption of a structure entirely in aluminum, which allows robustness while reducing the overall weight. The transmission system of motion has been optimized by means of brushless DC micro motors, light and compact, which helped to reduce weight, dimensions, power consumption and increase the reliability and durability of the system. The study of the dynamic behavior using SIMPACK, a multibody simulation software, led to results in line with those found in the most important and recent scientific publications. This model was also appropriately configured to represent any desired operating condition, and for eventual system scalability. It would be interesting to generate simulated hypogravity - e.g.: 0.38-g (Mars) or 0.17-g (Moon). This would allow to investigate how terrestrial life forms can grow in other planetary habitats, or to determine the gravity threshold response of different organisms. At the moment, such a system can only be achieved by centrifuges in real microgravity. We are confident that simulation and associated tests with our 3D clinostat can help adjusting the parameters allowing variable g

Automated simulation and study of spatial-structural design processes

NARCIS (Netherlands)

Davila Delgado, J.M.; Hofmeyer, H.; Stouffs, R.; Sariyildiz, S.

2013-01-01

A so-called "Design Process Investigation toolbox" (DPI toolbox), has been developed. It is a set of computational tools that simulate spatial-structural design processes. Its objectives are to study spatial-structural design processes and to support the involved actors. Two case-studies are

Evaluation of CMIP5 continental precipitation simulations relative to satellite-based gauge-adjusted observations

Science.gov (United States)

Mehran, A.; AghaKouchak, A.; Phillips, T. J.

2014-02-01

The objective of this study is to cross-validate 34 Coupled Model Intercomparison Project Phase 5 (CMIP5) historical simulations of precipitation against the Global Precipitation Climatology Project (GPCP) data, quantifying model pattern discrepancies, and biases for both entire distributions and their upper tails. The results of the volumetric hit index (VHI) analysis of the total monthly precipitation amounts show that most CMIP5 simulations are in good agreement with GPCP patterns in many areas but that their replication of observed precipitation over arid regions and certain subcontinental regions (e.g., northern Eurasia, eastern Russia, and central Australia) is problematical. Overall, the VHI of the multimodel ensemble mean and median also are superior to that of the individual CMIP5 models. However, at high quantiles of reference data (75th and 90th percentiles), all climate models display low skill in simulating precipitation, except over North America, the Amazon, and Central Africa. Analyses of total bias (B) in CMIP5 simulations reveal that most models overestimate precipitation over regions of complex topography (e.g., western North and South America and southern Africa and Asia), while underestimating it over arid regions. Also, while most climate model simulations show low biases over Europe, intermodel variations in bias over Australia and Amazonia are considerable. The quantile bias analyses indicate that CMIP5 simulations are even more biased at high quantiles of precipitation. It is found that a simple mean field bias removal improves the overall B and VHI values but does not make a significant improvement at high quantiles of precipitation.

Clarifying the learning experiences of healthcare professionals with in situ and off-site simulation-based medical education: a qualitative study.

Science.gov (United States)

Sørensen, Jette Led; Navne, Laura Emdal; Martin, Helle Max; Ottesen, Bent; Albrecthsen, Charlotte Krebs; Pedersen, Berit Woetmann; Kjærgaard, Hanne; van der Vleuten, Cees

2015-10-06

To examine how the setting in in situ simulation (ISS) and off-site simulation (OSS) in simulation-based medical education affects the perceptions and learning experience of healthcare professionals. Qualitative study using focus groups and content analysis. Twenty-five healthcare professionals (obstetricians, midwives, auxiliary nurses, anaesthesiologists, a nurse anaesthetist and operating theatre nurse) participated in four focus groups and were recruited due to their exposure to either ISS or OSS in multidisciplinary obstetric emergencies in a randomised trial. Departments of obstetrics and anaesthesia, Rigshospitalet, Copenhagen, Denmark. Initially participants preferred ISS, but this changed after the training when the simulation site became of less importance. There was a strong preference for simulation in authentic roles. These perceptions were independent of the ISS or OSS setting. Several positive and negative factors in simulation were identified, but these had no relation to the simulation setting. Participants from ISS and OSS generated a better understanding of and collaboration with the various health professionals. They also provided individual and team reflections on learning. ISS participants described more experiences that would involve organisational changes than the OSS participants did. Many psychological and sociological aspects related to the authenticity of the learning experience are important in simulation, but the physical setting of the simulation as an ISS and OSS is the least important. Based on these focus groups OSS can be used provided that all other authenticity elements are taken into consideration and respected. The only difference was that ISS had an organisational impact and ISS participants talked more about issues that would involve practical organisational changes. ISS and OSS participants did, however, go through similar individual and team learning experiences. Published by the BMJ Publishing Group Limited. For

Positron annihilation lifetime spectroscopy source correction determination: A simulation study

Energy Technology Data Exchange (ETDEWEB)

Kanda, Gurmeet S.; Keeble, David J., E-mail: d.j.keeble@dundee.ac.uk

2016-02-01

Positron annihilation lifetime spectroscopy (PALS) can provide sensitive detection and identification of vacancy-related point defects in materials. These measurements are normally performed using a positron source supported, and enclosed by, a thin foil. Annihilation events from this source arrangement must be quantified and are normally subtracted from the spectrum before analysis of the material lifetime components proceeds. Here simulated PALS spectra reproducing source correction evaluation experiments have been systematically fitted and analysed using the packages PALSfit and MELT. Simulations were performed assuming a single lifetime material, and for a material with two lifetime components. Source correction terms representing a directly deposited source and various foil supported sources were added. It is shown that in principle these source terms can be extracted from suitably designed experiments, but that fitting a number of independent, nominally identical, spectra is recommended.

Quench Simulation Studies: Program documentation of SPQR

CERN Document Server

Sonnemann, F

2001-01-01

Quench experiments are being performed on prototypes of the superconducting magnets and busbars to determine the adequate design and protection. Many tests can only be understood correctly with the help of quench simulations that model the thermo-hydraulic and electrodynamic processes during a quench. In some cases simulations are the only method to scale the experimental results of prototype measurements to match the situation of quenching superconducting elements in the LHC. This note introduces the theoretical quench model and the use of the simulation program SPQR (Simulation Program for Quench Research), which has been developed to compute the quench process in superconducting magnets and busbars. The model approximates the heat balance equation with the finite difference method including the temperature dependence of the material parameters. SPQR allows the simulation of longitudinal quench propagation along a superconducting cable, the transverse propagation between adjacent conductors, heat transfer i...

Study of swelling by simulation

International Nuclear Information System (INIS)

Gilbon, D.; Le Naour, L.; Didout, G.

1983-06-01

Fuel cans and hexagonal tubes containing the pins must withstand high irradiation doses (220 or even 275 dpa) with a low swelling. Qualification of a new alloy for claddings requires several years of irradiation on a reactor. For a fast first selection simulation by 1MeV electron or heavy ions enhance radiation damages. Principles of these techniques are recalled and some examples mainly with steel 316 are given. Results are compared with results obtained in reactor to determine simulation limits. The method is not valid in the case of a structural instability of the irradiated material in a reactor [fr

Improved GPS-based Satellite Relative Navigation Using Femtosecond Laser Relative Distance Measurements

Directory of Open Access Journals (Sweden)

Hyungjik Oh

2016-03-01

Full Text Available This study developed an approach for improving Carrier-phase Differential Global Positioning System (CDGPS based realtime satellite relative navigation by applying laser baseline measurement data. The robustness against the space operational environment was considered, and a Synthetic Wavelength Interferometer (SWI algorithm based on a femtosecond laser measurement model was developed. The phase differences between two laser wavelengths were combined to measure precise distance. Generated laser data were used to improve estimation accuracy for the float ambiguity of CDGPS data. Relative navigation simulations in real-time were performed using the extended Kalman filter algorithm. The GPS and laser-combined relative navigation accuracy was compared with GPS-only relative navigation solutions to determine the impact of laser data on relative navigation. In numerical simulations, the success rate of integer ambiguity resolution increased when laser data was added to GPS data. The relative navigational errors also improved five-fold and two-fold, relative to the GPS-only error, for 250 m and 5 km initial relative distances, respectively. The methodology developed in this study is suitable for application to future satellite formation-flying missions.

Simulation study of the beam-beam interaction at SPEAR

International Nuclear Information System (INIS)

Tennyson, J.

1980-01-01

A two dimensional simulation study of the beam-beam interaction at SPEAR indicates that quantum fluctuations affecting the horizontal betatron oscillation play a critical role in the vertical beam blowup

Does removal of mammalian predators significantly affect success of simulated nests in linear habitats? Case study on American mink Mustela vison \\& Predation on simulated duck nests in relation to nest density and habitat type

OpenAIRE

PADYŠÁKOVÁ, Eliška

2007-01-01

This thesis is made up of two studies dealing with predation of waterfowl nests. in the first study, we determined wheather removal of introduced predator Mustela vison affected nest survival of simulated duck nests in linear habitat. In the second study, we tested two hypothesis: 1)predation depends on density of waterfowl nests, 2)mammals are main predators in forest habitat and birds mainly depredate nests deployed in open land.

Realistic electricity market simulator for energy and economic studies

International Nuclear Information System (INIS)

Bernal-Agustin, Jose L.; Contreras, Javier; Conejo, Antonio J.; Martin-Flores, Raul

2007-01-01

Electricity market simulators have become a useful tool to train engineers in the power industry. With the maturing of electricity markets throughout the world, there is a need for sophisticated software tools that can replicate the actual behavior of power markets. In most of these markets, power producers/consumers submit production/demand bids and the Market Operator clears the market producing a single price per hour. What makes markets different from each other are the bidding rules and the clearing algorithms to balance the market. This paper presents a realistic simulator of the day-ahead electricity market of mainland Spain. All the rules that govern this market are modeled. This simulator can be used either to train employees by power companies or to teach electricity markets courses in universities. To illustrate the tool, several realistic case studies are presented and discussed. (author)

8th International Workshop on Simulation

CERN Document Server

Rasch, Dieter; Melas, Viatcheslav; Moder, Karl; Statistics and simulation

2018-01-01

This volume features original contributions and invited review articles on mathematical statistics, statistical simulation and experimental design. The selected peer-reviewed contributions originate from the 8th International Workshop on Simulation held in Vienna in 2015. The book is intended for mathematical statisticians, Ph.D. students and statisticians working in medicine, engineering, pharmacy, psychology, agriculture and other related fields. The International Workshops on Simulation are devoted to statistical techniques in stochastic simulation, data collection, design of scientific experiments and studies representing broad areas of interest. The first 6 workshops took place in St. Petersburg, Russia, in 1994 – 2009 and the 7th workshop was held in Rimini, Italy, in 2013.

MODELING SIMULATION AND PERFORMANCE STUDY OF GRIDCONNECTED PHOTOVOLTAIC ENERGY SYSTEM

OpenAIRE

Nagendra K; Karthik J; Keerthi Rao C; Kumar Raja Pemmadi

2017-01-01

This paper presents Modeling Simulation of grid connected Photovoltaic Energy System and performance study using MATLAB/Simulink. The Photovoltaic energy system is considered in three main parts PV Model, Power conditioning System and Grid interface. The Photovoltaic Model is inter-connected with grid through full scale power electronic devices. The simulation is conducted on the PV energy system at normal temperature and at constant load by using MATLAB.

Physically realistic modeling of maritime training simulation

OpenAIRE

Cieutat , Jean-Marc

2003-01-01

Maritime training simulation is an important matter of maritime teaching, which requires a lot of scientific and technical skills.In this framework, where the real time constraint has to be maintained, all physical phenomena cannot be studied; the most visual physical phenomena relating to the natural elements and the ship behaviour are reproduced only. Our swell model, based on a surface wave simulation approach, permits to simulate the shape and the propagation of a regular train of waves f...

High temperature breakdown of the Stokes-Einstein relation in a computer simulated Cu-Zr melt

Energy Technology Data Exchange (ETDEWEB)

Han, X. J., E-mail: xjhan@sjtu.edu.cn; Li, J. G., E-mail: lijg@sjtu.edu.cn [School of Materials Science and Engineering, Shanghai Jiao Tong University, Dongchuan Rd. 800, 200240 Shanghai (China); Schober, H. R., E-mail: h.schober@fz-juelich.de [Peter Grünberg Institut, Forschungszentrum Jülich, D-52425 Jülich (Germany)

2016-03-28

Transport properties and the Stokes-Einstein (SE) relation in liquid Cu{sub 8}Zr{sub 3} are studied by molecular dynamics simulation with a modified embedded atom potential. The critical temperature T{sub c} of mode coupling theory (MCT) is derived as 930 K from the self-diffusion coefficient D and viscosity η. The SE relation breaks down around T{sub SE} = 1900 K, which is far above T{sub c}. At temperatures below T{sub SE}, the product of D and η fluctuates around a constant value, similar to the prediction of MCT near T{sub c}. The influence of the microscopic atomic motion on macroscopic properties is investigated by analyzing the time dependent liquid structure and the self-hole filling process. The self-holes for the two components are preferentially filled by atoms of the same component. The self-hole filling dynamics explains the different breakdown behaviors of the SE relation in Zr-rich liquid CuZr{sub 2} compared to Cu-rich Cu{sub 8}Zr{sub 3}. At T{sub SE}, a kink is found in the temperature dependence of both partial and total coordination numbers for the three atomic pair combinations and of the typical time of self-hole filling. This indicates a strong correlation between liquid structure, atomic dynamics, and the breakdown of SE relation. The previously suggested usefulness of the parameter d(D{sub 1}/D{sub 2})/dT to predict T{sub SE} is confirmed. Additionally we propose a viscosity criterion to predict T{sub SE} in the absence of diffusion data.

A SAS-based solution to evaluate study design efficiency of phase I pediatric oncology trials via discrete event simulation.

Science.gov (United States)

Barrett, Jeffrey S; Jayaraman, Bhuvana; Patel, Dimple; Skolnik, Jeffrey M

2008-06-01

Previous exploration of oncology study design efficiency has focused on Markov processes alone (probability-based events) without consideration for time dependencies. Barriers to study completion include time delays associated with patient accrual, inevaluability (IE), time to dose limiting toxicities (DLT) and administrative and review time. Discrete event simulation (DES) can incorporate probability-based assignment of DLT and IE frequency, correlated with cohort in the case of DLT, with time-based events defined by stochastic relationships. A SAS-based solution to examine study efficiency metrics and evaluate design modifications that would improve study efficiency is presented. Virtual patients are simulated with attributes defined from prior distributions of relevant patient characteristics. Study population datasets are read into SAS macros which select patients and enroll them into a study based on the specific design criteria if the study is open to enrollment. Waiting times, arrival times and time to study events are also sampled from prior distributions; post-processing of study simulations is provided within the decision macros and compared across designs in a separate post-processing algorithm. This solution is examined via comparison of the standard 3+3 decision rule relative to the "rolling 6" design, a newly proposed enrollment strategy for the phase I pediatric oncology setting.

A New Simulation Technique for Study of Collisionless Shocks: Self-Adaptive Simulations

International Nuclear Information System (INIS)

Karimabadi, H.; Omelchenko, Y.; Driscoll, J.; Krauss-Varban, D.; Fujimoto, R.; Perumalla, K.

2005-01-01

The traditional technique for simulating physical systems modeled by partial differential equations is by means of time-stepping methodology where the state of the system is updated at regular discrete time intervals. This method has inherent inefficiencies. In contrast to this methodology, we have developed a new asynchronous type of simulation based on a discrete-event-driven (as opposed to time-driven) approach, where the simulation state is updated on a 'need-to-be-done-only' basis. Here we report on this new technique, show an example of particle acceleration in a fast magnetosonic shockwave, and briefly discuss additional issues that we are addressing concerning algorithm development and parallel execution

Study and simulation of a parallel numerical processing machine

International Nuclear Information System (INIS)

Bel Hadj, Slaheddine

1981-12-01

This study has been carried out in the perspective of the implementation on a minicomputer of the NEPTUNIX package (software for the resolution of very large algebra-differential equation systems). Aiming at increasing the system performance, a previous research work has shown the necessity of reducing the execution time of certain numerical computation tasks, which are of frequent use. It has also demonstrated the feasibility of handling these tasks with efficient algorithms of parallel type. The present work deals with the study and simulation of a parallel architecture processor adapted to the fast execution of these algorithms. A minicomputer fitted with a connection to such a parallel processor, has a greatly extended computing power. Then the architecture of a parallel numerical processor, based on the use of VLSI microprocessors and co-processors, is described. Its design aims at the best cost / performance ratio. The last part deals with the simulation processor with the 'CHAMBOR' program. Results show an increasing factor of 30 in speed, in comparison with the execution on a MITRA 15 minicomputer. Moreover the conflicts importance, mainly at the level of access to a shared resource is evaluated. Although this implementation has been designed having in mind a dedicated application, other uses could be envisaged, particularly for the simulation of nuclear reactors: operator guiding system, the behavioural study under accidental circumstances, etc. (author) [fr

Study of Gamma spectra by Monte Carlo simulation

International Nuclear Information System (INIS)

Cantaragiu, A.; Gheorghies, A.; Borcia, C.

2008-01-01

The purpose of this paper is obtaining gamma ray spectra by means of a scintillation detector applying the Monte Carlo statistic simulation method using the EGS4 program. The Monte Carlo algorithm implies that the physical system is described by the probability density function which allows generating random figures and the result is taken as an average of numbers which were observed. The EGS4 program allows the simulation of the following physical processes: the photo-electrical effect, the Compton effect, the electron positron pairs generation and the Rayleigh diffusion. The gamma rays recorded by the detector are converted into electrical pulses and the gamma ray spectra are acquired and processed by means of the Nomad Plus portable spectrometer connected to a computer. As a gamma ray sources 137Cs and 60Co are used whose spectra drawn and used for study the interaction of the gamma radiations with the scintillation detector. The parameters which varied during the acquisition of the gamma ray spectra are the distance between source and detector and the measuring time. Due to the statistical processes in the detector, the peak looks like a Gauss distribution. The identification of the gamma quantum energy value is achieved by the experimental spectra peaks, thus gathering information about the position of the peak, the width and the area of the peak respectively. By means of the EGS4 program a simulation is run using these parameters and an 'ideal' spectrum is obtained, a spectrum which is not influenced by the statistical processes which take place inside the detector. Then, the convolution of the spectra is achieved by means of a normalised Gauss function. There is a close match between the experimental results and those simulated in the EGS4 program because the interactions which occurred during the simulation have a statistical behaviour close to the real one. (authors)

Simulation study of an automated storage/retrieval system

NARCIS (Netherlands)

Berg, van den J.P.; Gademann, A.J.R.M.

2000-01-01

In this paper we present a simulation study of an automated storage/retrieval system and examine a wide variety of control policies. We compare several storage location assignment policies. For the class-based storage policy, we apply a recent algorithm that enables us to evaluate the trade-off

Injector and beam transport simulation study of proton dielectric wall accelerator

International Nuclear Information System (INIS)

Zhao, Quantang; Yuan, P.; Zhang, Z.M.; Cao, S.C; Shen, X.K.; Jing, Y.; Ma, Y.Y.; Yu, C.S.; Li, Z.P.; Liu, M.; Xiao, R.Q.; Zhao, H.W.

2012-01-01

A simulation study of a short-pulsed proton injector for, and beam transport in, a dielectric wall accelerator (DWA) has been carried out using the particle-in-cell (PIC) code Warp. It was shown that applying “tilt pulse” voltage waveforms on three electrodes enables the production of a shorter bunch by the injector. The fields in the DWA beam tube were simulated using Computer Simulation Technology’s Microwave Studio (CST MWS) package, with various choices for the boundary conditions. For acceleration in the DWA, the beam transport was simulated with Warp, using applied fields obtained by running CST MWS. Our simulations showed that the electric field at the entrance to the DWA represents a challenging issue for the beam transport. We thus simulated a configuration with a mesh at the entrance of the DWA, intended to improve the entrance field. In these latter simulations, a proton bunch was successfully accelerated from 130 keV to about 36 MeV in a DWA with a length of 36.75 cm. As the beam bunch progresses, its transverse dimensions diminish from (roughly) 0.5×0.5 cm to 0.2×0.4 cm. The beam pulse lengthens from 1 cm to 2 cm due to lack of longitudinal compression fields. -- Highlights: ► A pulse proton injector with tilt voltages on the three electrodes was simulated. ► The fields in different part of the DWA were simulated with CST and analyzed. ► The proton beam transport in DWA was simulated with Warp successfully. ► The simulation can help for designing a real DWA.

How do pharmacists respond to complaints of acute insomnia? A simulated patient study.

Science.gov (United States)

Kippist, Carly; Wong, Keith; Bartlett, Delwyn; Saini, Bandana

2011-04-01

It is known that many people with insomnia choose to self medicate and present at community pharmacies, particularly in cases of acute insomnia. The objective of this study is to investigate how community pharmacists respond to complaints of acute insomnia from people who seek self treatment and determine the factors affecting this response. Community pharmacies in New South Wales, Australia. A simulated patient study was conducted in 100 randomly selected pharmacies located in Newcastle and Sydney, Australia. A standardized scenario of acute sleep onset insomnia and a scoring system was used in each pharmacy. Main outcome measures included supply/non supply of an over the counter sleep aid to the simulated patient, and scores for pharmacists for skills in eliciting information prior to supply of medication (Pre Supply Score), counseling about medication (Supply Score), or about sleep (Sleep Score). Of the 100 pharmacies, upon simulated patient presentation, 96% supplied a product, the remaining 4% referred to a physician. Non-pharmacological advice was provided in 42%. Pharmacists scored highly on advice provided with supply of a medication (Supply scores/4, 3.1 ± 0.9), but lower on skills in eliciting information prior to supply (Pre-supply score/8, 3.6 ± 1.9) and sleep related counselling (Sleep Score/9, 2.1 ± 1.7). Lower estimated pharmacist age, being in a chain type pharmacy, and having a visible symbol of quality accreditation were found to significantly improve (P Supply Score (P Supply scores (P < 0.05). The results of this study suggest that many pharmacists are responding appropriately to complaints of sleeplessness in terms of eliciting insomnia type and counseling about medicines use. However more education for pharmacists would help to further promote good sleep health, and address behaviors including reliance on medicines taking that can progressively worsen insomnia.

Formation of Nanophase Iron in Lunar Soil Simulant for Use in ISRU Studies

Science.gov (United States)

Liu, Yang; Taylor, Lawrence A.; Hill, Eddy; Day, James D. M.

2005-01-01

For the prospective return of humans to the Moon and the extensive amount of premonitory studies necessary, large quantities of lunar soil simulants are required, for a myriad of purposes from construction/engineering purposes all the way to medical testing of its effects from ingestion by humans. And there is only a limited and precious quantity of lunar soil available on Earth (i.e., Apollo soils) - therefore, the immediate need for lunar soil simulants. Since the Apollo era, there have been several simulants; of these JSC-1 (Johnson Space Center) and MLS-1 (Minnesota Lunar Simulant) have been the most widely used. JSC-1 was produced from glassy volcanic tuff in order to approximate lunar soil geotechnical properties; whereas, MLS-1 approximates the chemistry of Apollo 11 high-Ti soil, 10084. Stocks of both simulants are depleted, but JSC-1 has recently gone back into production. The lunar soil simulant workshop, held at Marshall Space Flight Center in January 2005, identified the need to make new simulants for the special properties of lunar soil, such as nanophase iron (np-Fe(sup 0). Hill et al. (2005, this volume) showed the important role of microscale Fe(sup 0) in microwave processing of the lunar soil simulants JSC-1 and MLS-1. Lunar soil is formed by space weathering of lunar rocks (e.g., micrometeorite impact, cosmic particle bombardment). Glass generated during micrometeorite impact cements rock and mineral fragments together to form aggregates called agglutinates, and also produces vapor that is deposited and coats soil grains. Taylor et al. (2001) showed that the relative amount of impact glass in lunar soil increases with decreasing grain size and is the most abundant component in lunar dust (less than 20 micrometer fraction). Notably, the magnetic susceptibility of lunar soil also increases with the decreasing grain size, as a function of the amount of nanophase-sized Fe(sup 0) in impact-melt generated glass. Keller et al. (1997, 1999) also

Agent Behavior-Based Simulation Study on Mass Collaborative Product Development Process

Directory of Open Access Journals (Sweden)

Shuo Zhang

2015-01-01

Full Text Available Mass collaborative product development (MCPD benefits people by high innovation products with lower cost and shorter lead time due to quick development of group innovation, Internet-based customization, and prototype manufacturing. Simulation is an effective way to study the evolution process and therefore to guarantee the success of MCPD. In this paper, an agent behavior-based simulation approach of MCPD is developed, which models the MCPD process as the interactive process of design agents and the environment objects based on Complex Adaptive System (CAS theory. Next, the structure model of design agent is proposed, and the modification and collaboration behaviors are described. Third, the agent behavior-based simulation flow of MCPD is designed. At last, simulation experiments are carried out based on an engineering case of mobile phone design. The experiment results show the following: (1 the community scale has significant influence on MCPD process; (2 the simulation process can explicitly represent the modification and collaboration behaviors of design agents; (3 the community evolution process can be observed and analyzed dynamically based on simulation data.

Simulator configuration management system

International Nuclear Information System (INIS)

Faulent, J.; Brooks, J.G.

1990-01-01

The proposed revisions to ANS 3.5-1985 (Section 5) require Utilities to establish a simulator Configuration Management System (CMS). The proposed CMS must be capable of: Establishing and maintaining a simulator design database. Identifying and documenting differences between the simulator and its reference plant. Tracking the resolution of identified differences. Recording data to support simulator certification, testing and maintenance. This paper discusses a CMS capable of meeting the proposed requirements contained in ANS 3.5. The system will utilize a personal computer and a relational database management software to construct a simulator design database. The database will contain records to all reference nuclear plant data used in designing the simulator, as well as records identifying all the software, hardware and documentation making up the simulator. Using the relational powers of the database management software, reports will be generated identifying the impact of reference plant changes on the operation of the simulator. These reports can then be evaluated in terms of training needs to determine if changes are required for the simulator. If a change is authorized, the CMS will track the change through to its resolution and then incorporate the change into the simulator design database

Studying distributed cognition of simulation-based team training with DiCoT.

Science.gov (United States)

Rybing, Jonas; Nilsson, Heléne; Jonson, Carl-Oscar; Bang, Magnus

2016-03-01

Health care organizations employ simulation-based team training (SBTT) to improve skill, communication and coordination in a broad range of critical care contexts. Quantitative approaches, such as team performance measurements, are predominantly used to measure SBTTs effectiveness. However, a practical evaluation method that examines how this approach supports cognition and teamwork is missing. We have applied Distributed Cognition for Teamwork (DiCoT), a method for analysing cognition and collaboration aspects of work settings, with the purpose of assessing the methodology's usefulness for evaluating SBTTs. In a case study, we observed and analysed four Emergo Train System® simulation exercises where medical professionals trained emergency response routines. The study suggests that DiCoT is an applicable and learnable tool for determining key distributed cognition attributes of SBTTs that are of importance for the simulation validity of training environments. Moreover, we discuss and exemplify how DiCoT supports design of SBTTs with a focus on transfer and validity characteristics. Practitioner Summary: In this study, we have evaluated a method to assess simulation-based team training environments from a cognitive ergonomics perspective. Using a case study, we analysed Distributed Cognition for Teamwork (DiCoT) by applying it to the Emergo Train System®. We conclude that DiCoT is useful for SBTT evaluation and simulator (re)design.

SED-ML web tools: generate, modify and export standard-compliant simulation studies.

Science.gov (United States)

Bergmann, Frank T; Nickerson, David; Waltemath, Dagmar; Scharm, Martin

2017-04-15

The Simulation Experiment Description Markup Language (SED-ML) is a standardized format for exchanging simulation studies independently of software tools. We present the SED-ML Web Tools, an online application for creating, editing, simulating and validating SED-ML documents. The Web Tools implement all current SED-ML specifications and, thus, support complex modifications and co-simulation of models in SBML and CellML formats. Ultimately, the Web Tools lower the bar on working with SED-ML documents and help users create valid simulation descriptions. http://sysbioapps.dyndns.org/SED-ML_Web_Tools/ . fbergman@caltech.edu . © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com

Co-Simulation of Detailed Whole Building with the Power System to Study Smart Grid Applications

Energy Technology Data Exchange (ETDEWEB)

Makhmalbaf, Atefe; Fuller, Jason C.; Srivastava, Viraj; Ciraci, Selim; Daily, Jeffrey A.

2014-12-24

Modernization of the power system in a way that ensures a sustainable energy system is arguably one of the most pressing concerns of our time. Buildings are important components in the power system. First, they are the main consumers of electricity and secondly, they do not have constant energy demand. Conventionally, electricity has been difficult to store and should be consumed as it is generated. Therefore, maintaining the demand and supply is critical in the power system. However, to reduce the complexity of power models, buildings (i.e., end-use loads) are traditionally modeled and represented as aggregated “dumb” nodes in the power system. This means we lack effective detailed whole building energy models that can support requirements and emerging technologies of the smart power grid. To gain greater insight into the relationship between building energy demand and power system performance, it is important to constitute a co-simulation framework to support detailed building energy modeling and simulation within the power system to study capabilities promised by the modern power grid. This paper discusses ongoing work at Pacific Northwest National Laboratory and presents underlying tools and framework needed to enable co-simulation of building, building energy systems and their control in the power system to study applications such as demand response, grid-based HVAC control, and deployment of buildings for ancillary services. The optimal goal is to develop an integrated modeling and simulation platform that is flexible, reusable, and scalable. Results of this work will contribute to future building and power system studies, especially those related to the integrated ‘smart grid’. Results are also expected to advance power resiliency and local (micro) scale grid studies where several building and renewable energy systems transact energy directly. This paper also reviews some applications that can be supported and studied using the framework introduced

Indicial lift response function: an empirical relation for finite‐thickness airfoils, and effects on aeroelastic simulations

DEFF Research Database (Denmark)

Bergami, Leonardo; Gaunaa, Mac; Heinz, Joachim Christian

2013-01-01

The aeroelastic response of wind turbines is often simulated in the time domain by using indicial response techniques. Unsteady aerodynamics in attached flow are usually based on Jones's approximation of the flat plate indicial response, although the response for finite‐thickness airfoils differs...... from the flat plate one. The indicial lift response of finite‐thickness airfoils is simulated with a panel code, and an empirical relation is outlined connecting the airfoil indicial response to its geometric characteristics. The effects of different indicial approximations are evaluated on a 2D...... of equivalent fatigue loads, ultimate loads, and stability limits. The agreement with CFD computations of a 2D profile in harmonic motion is improved by the indicial function accounting for the finite‐thickness of the airfoil. Concerning the full wind turbine aeroelastic behavior, the differences between...

Simulation Study of a Vehicle Production Line for Productivity Improvement

Directory of Open Access Journals (Sweden)

M.F.F. Ab Rashid

2015-06-01

Full Text Available This paper presents the study of a motorcycle frame production line in a particular company in Malaysia. Due to the high demand, the company needs to increase its production by at least 12% compared with current output. In order to improve productivity, the production-floor data was collected and simulated using the discrete event simulation approach. Later, a number of suggestions for improvement were simulated to identify the effect of the suggestions on productivity. In addition, cost analysis was also undertaken to identify the profit margin for a particular period of time for each suggestion. Simulation results indicate that there are three suggestions that are able to fulfill the 12% volume increment. In the short term, the suggestion to hire an assistant line leader will give instant effect to the profit. Meanwhile, for the medium term, Poka-yoke will give higher profit compared with the others, while in the long term, SOP (standard operating procedure implementation will yield a better profit margin. In future, the simulation of a dynamic demand model for this product is suggested to cope with new trends in the market.

Prospective randomized study of contrast reaction management curricula: Computer-based interactive simulation versus high-fidelity hands-on simulation

Energy Technology Data Exchange (ETDEWEB)

Wang, Carolyn L., E-mail: wangcl@uw.edu [Department of Radiology, University of Washington, Box 357115, 1959 NE Pacific Street, Seattle, WA 98195-7115 (United States); Schopp, Jennifer G.; Kani, Kimia [Department of Radiology, University of Washington, Box 357115, 1959 NE Pacific Street, Seattle, WA 98195-7115 (United States); Petscavage-Thomas, Jonelle M. [Penn State Hershey Medical Center, Department of Radiology, 500 University Drive, Hershey, PA 17033 (United States); Zaidi, Sadaf; Hippe, Dan S.; Paladin, Angelisa M.; Bush, William H. [Department of Radiology, University of Washington, Box 357115, 1959 NE Pacific Street, Seattle, WA 98195-7115 (United States)

2013-12-01

Purpose: We developed a computer-based interactive simulation program for teaching contrast reaction management to radiology trainees and compared its effectiveness to high-fidelity hands-on simulation training. Materials and methods: IRB approved HIPAA compliant prospective study of 44 radiology residents, fellows and faculty who were randomized into either the high-fidelity hands-on simulation group or computer-based simulation group. All participants took separate written tests prior to and immediately after their intervention. Four months later participants took a delayed written test and a hands-on high-fidelity severe contrast reaction scenario performance test graded on predefined critical actions. Results: There was no statistically significant difference between the computer and hands-on groups’ written pretest, immediate post-test, or delayed post-test scores (p > 0.6 for all). Both groups’ scores improved immediately following the intervention (p < 0.001). The delayed test scores 4 months later were still significantly higher than the pre-test scores (p ≤ 0.02). The computer group's performance was similar to the hands-on group on the severe contrast reaction simulation scenario test (p = 0.7). There were also no significant differences between the computer and hands-on groups in performance on the individual core competencies of contrast reaction management during the contrast reaction scenario. Conclusion: It is feasible to develop a computer-based interactive simulation program to teach contrast reaction management. Trainees that underwent computer-based simulation training scored similarly on written tests and on a hands-on high-fidelity severe contrast reaction scenario performance test as those trained with hands-on high-fidelity simulation.

Prospective randomized study of contrast reaction management curricula: Computer-based interactive simulation versus high-fidelity hands-on simulation

International Nuclear Information System (INIS)

Wang, Carolyn L.; Schopp, Jennifer G.; Kani, Kimia; Petscavage-Thomas, Jonelle M.; Zaidi, Sadaf; Hippe, Dan S.; Paladin, Angelisa M.; Bush, William H.

2013-01-01

Purpose: We developed a computer-based interactive simulation program for teaching contrast reaction management to radiology trainees and compared its effectiveness to high-fidelity hands-on simulation training. Materials and methods: IRB approved HIPAA compliant prospective study of 44 radiology residents, fellows and faculty who were randomized into either the high-fidelity hands-on simulation group or computer-based simulation group. All participants took separate written tests prior to and immediately after their intervention. Four months later participants took a delayed written test and a hands-on high-fidelity severe contrast reaction scenario performance test graded on predefined critical actions. Results: There was no statistically significant difference between the computer and hands-on groups’ written pretest, immediate post-test, or delayed post-test scores (p > 0.6 for all). Both groups’ scores improved immediately following the intervention (p < 0.001). The delayed test scores 4 months later were still significantly higher than the pre-test scores (p ≤ 0.02). The computer group's performance was similar to the hands-on group on the severe contrast reaction simulation scenario test (p = 0.7). There were also no significant differences between the computer and hands-on groups in performance on the individual core competencies of contrast reaction management during the contrast reaction scenario. Conclusion: It is feasible to develop a computer-based interactive simulation program to teach contrast reaction management. Trainees that underwent computer-based simulation training scored similarly on written tests and on a hands-on high-fidelity severe contrast reaction scenario performance test as those trained with hands-on high-fidelity simulation

Comparative Study of Algorithms for the Numerical Simulation of Lattice QCD

International Nuclear Information System (INIS)

Luz, Fernando H. P.; Mendes, Tereza

2010-01-01

Large-scale numerical simulations are the prime method for a nonperturbative study of QCD from first principles. Although the lattice simulation of the pure-gauge (or quenched-QCD) case may be performed very efficiently on parallel machines, there are several additional difficulties in the simulation of the full-QCD case, i.e. when dynamical quark effects are taken into account. We discuss the main aspects of full-QCD simulations, describing the most common algorithms. We present a comparative analysis of performance for two versions of the hybrid Monte Carlo method (the so-called R and RHMC algorithms), as provided in the MILC software package. We consider two degenerate flavors of light quarks in the staggered formulation, having in mind the case of finite-temperature QCD.

Comparison of classic simulation and virtual simulation in breast irradiation: prospective study on 14 patients

International Nuclear Information System (INIS)

Bauduceau, O.; Pons, P.; Romero, L.; Fayolle, M.; Campana, F.; Bollet, M.

2005-01-01

Purpose. - To compare conventional 2D simulation and virtual simulation on 14 patients with breast cancer. Patients and methods. - Patients were simulated for treatment using standard procedure. They subsequently underwent CT scan in the treatment position. The CTV was defined as breast tissue. The PTV was obtained by adding a 3D margin of 1 cm around CTV. Organs at risk (lungs and heart) were outlined. Ballistics and dose distribution obtained with the two planning methods were compared. Results. - With conventional simulation, 95% of CTV received 95% of the dose prescribed. Virtual simulation significantly improved dosimetric coverage of PTV without increasing irradiation volume of lung and heart. In 2D simulation, using three slices allowed optimisation by adjusting wedge angle. The five-slice plan was a much better predictor of the maximum dose regions when compared to the three-slice plan. Using entire CT data did not give any benefit. Conclusion. - Variations in CTV delineation and PTV definition limit interest of virtual simulation. In classic simulation, a 5 CT slice-plan can be used to optimise dose distribution. (author)

Tight binding simulation study on zigzag single-walled carbon nanotubes

Science.gov (United States)

Sharma, Deepa; Jaggi, Neena; Gupta, Vishu

2018-01-01

Tight binding simulation studies using the density functional tight binding (DFTB) model have been performed on various zigzag single-walled carbon-nanotubes (SWCNTs) to investigate their electronic properties using DFTB module of the Material Studio Software version 7.0. Various combinations of different eigen-solvers and charge mixing schemes available in the DFTB Module have been tried to chalk out the electronic structure. The analytically deduced values of the bandgap of (9, 0) SWCNT were compared with the experimentally determined value reported in the literature. On comparison, it was found that the tight binding approximations tend to drastically underestimate the bandgap values. However, the combination of Anderson charge mixing method with standard eigensolver when implemented using the smart algorithm was found to produce fairly close results. These optimized model parameters were then used to determine the band structures of various zigzag SWCNTs. (9, 0) Single-walled Nanotube which is extensively being used for sensing NH3, CH4 and NO2 has been picked up as a reference material since its experimental bandgap value has been reported in the literature. It has been found to exhibit a finite energy bandgap in contrast to its expected metallic nature. The study is of utmost significance as it not only probes and validates the simulation route for predicting suitable properties of nanomaterials but also throws light on the comparative efficacy of the different approximation and rationalization quantum mechanical techniques used in simulation studies. Such simulation studies if used intelligently prove to be immensely useful to the material scientists as they not only save time and effort but also pave the way to new experiments by making valuable predictions.

Study of Monte Carlo Simulation Method for Methane Phase Diagram Prediction using Two Different Potential Models

KAUST Repository

Kadoura, Ahmad

2011-06-06

Lennard‐Jones (L‐J) and Buckingham exponential‐6 (exp‐6) potential models were used to produce isotherms for methane at temperatures below and above critical one. Molecular simulation approach, particularly Monte Carlo simulations, were employed to create these isotherms working with both canonical and Gibbs ensembles. Experiments in canonical ensemble with each model were conducted to estimate pressures at a range of temperatures above methane critical temperature. Results were collected and compared to experimental data existing in literature; both models showed an elegant agreement with the experimental data. In parallel, experiments below critical temperature were run in Gibbs ensemble using L‐J model only. Upon comparing results with experimental ones, a good fit was obtained with small deviations. The work was further developed by adding some statistical studies in order to achieve better understanding and interpretation to the estimated quantities by the simulation. Methane phase diagrams were successfully reproduced by an efficient molecular simulation technique with different potential models. This relatively simple demonstration shows how powerful molecular simulation methods could be, hence further applications on more complicated systems are considered. Prediction of phase behavior of elemental sulfur in sour natural gases has been an interesting and challenging field in oil and gas industry. Determination of elemental sulfur solubility conditions helps avoiding all kinds of problems caused by its dissolution in gas production and transportation processes. For this purpose, further enhancement to the methods used is to be considered in order to successfully simulate elemental sulfur phase behavior in sour natural gases mixtures.

Do Simulations Enhance Student Learning? An Empirical Evaluation of an IR Simulation

Science.gov (United States)

Shellman, Stephen M.; Turan, Kursad

2006-01-01

There is a nascent literature on the question of whether active learning methods, and in particular simulation methods, enhance student learning. In this article, the authors evaluate the utility of an international relations simulation in enhancing learning objectives. Student evaluations provide evidence that the simulation process enhances…

Vacancy profile in reverse osmosis membranes studied by positron annihilation lifetime measurements and molecular dynamics simulations

International Nuclear Information System (INIS)

Shimazu, A; Shintani, T; Hirose, M; Goto, H; Suzuki, R; Kobayashi, Y

2013-01-01

The positron annihilation technique using a slow positron beam can be used for the study of the vacancy profiles in typical reverse osmosis (RO) membranes. In this study, the vacancy profile in the polyamide membrane that exhibits a high permselectivity between ions and water was studied using the positron annihilation technique and molecular dynamics simulations. Ortho-positronium (o-Ps) lifetimes in the surface region of the membranes were evaluated by using a slow positron beam. The diffusion behavior of Na + and water in the polyamides was simulated by molecular dynamics (MD) methods using the TSUBAME2 supercomputer at the Tokyo Institute of Technology and discussed with the vacancy profile probed by the o-Ps. The results suggested that the large hydration size of Na + compared to the vacancy size in the polyamides contributes to the increased diffusivity selectivity of water/Na + that is related to the NaCl desalination performance of the membrane. Both the hydration size of the ions and the vacancy size appeared to be significant parameters to discuss the diffusivity selectivity of water/ions in typical polyamide membranes.

Performance of informative priors skeptical of large treatment effects in clinical trials: A simulation study.

Science.gov (United States)

Pedroza, Claudia; Han, Weilu; Thanh Truong, Van Thi; Green, Charles; Tyson, Jon E

2018-01-01

One of the main advantages of Bayesian analyses of clinical trials is their ability to formally incorporate skepticism about large treatment effects through the use of informative priors. We conducted a simulation study to assess the performance of informative normal, Student- t, and beta distributions in estimating relative risk (RR) or odds ratio (OR) for binary outcomes. Simulation scenarios varied the prior standard deviation (SD; level of skepticism of large treatment effects), outcome rate in the control group, true treatment effect, and sample size. We compared the priors with regards to bias, mean squared error (MSE), and coverage of 95% credible intervals. Simulation results show that the prior SD influenced the posterior to a greater degree than the particular distributional form of the prior. For RR, priors with a 95% interval of 0.50-2.0 performed well in terms of bias, MSE, and coverage under most scenarios. For OR, priors with a wider 95% interval of 0.23-4.35 had good performance. We recommend the use of informative priors that exclude implausibly large treatment effects in analyses of clinical trials, particularly for major outcomes such as mortality.

Simulations in nursing practice: toward authentic leadership.

Science.gov (United States)

Shapira-Lishchinsky, Orly

2014-01-01

Aim  This study explores nurses' ethical decision-making in team simulations in order to identify the benefits of these simulations for authentic leadership. Background  While previous studies have indicated that team simulations may improve ethics in the workplace by reducing the number of errors, those studies focused mainly on clinical aspects and not on nurses' ethical experiences or on the benefits of authentic leadership. Methods  Fifty nurses from 10 health institutions in central Israel participated in the study. Data about nurses' ethical experiences were collected from 10 teams. Qualitative data analysis based on Grounded Theory was applied, using the atlas.ti 5.0 software package. Findings  Simulation findings suggest four main benefits that reflect the underlying components of authentic leadership: self-awareness, relational transparency, balanced information processing and internalized moral perspective. Conclusions  Team-based simulation as a training tool may lead to authentic leadership among nurses. Implications for nursing management  Nursing management should incorporate team simulations into nursing practice to help resolve power conflicts and to develop authentic leadership in nursing. Consequently, errors will decrease, patients' safety will increase and optimal treatment will be provided. © 2012 John Wiley & Sons Ltd.

Status of the TOUGH-FLAC simulator and recent applications related to coupled fluid flow and crustal deformations

Energy Technology Data Exchange (ETDEWEB)

Rutqvist, J.

2010-06-01

This paper presents recent advancement in and applications of TOUGH-FLAC, a simulator for multiphase fluid flow and geomechanics. The TOUGH-FLAC simulator links the TOUGH family multiphase fluid and heat transport codes with the commercial FLAC{sup 3D} geomechanical simulator. The most significant new TOUGH-FLAC development in the past few years is a revised architecture, enabling a more rigorous and tight coupling procedure with improved computational efficiency. The applications presented in this paper are related to modeling of crustal deformations caused by deep underground fluid movements and pressure changes as a result of both industrial activities (the In Salah CO{sub 2} Storage Project and the Geysers Geothermal Field) and natural events (the 1960s Matsushiro Earthquake Swarm). Finally, the paper provides some perspectives on the future of TOUGH-FLAC in light of its applicability to practical problems and the need for high-performance computing capabilities for field-scale problems, such as industrial-scale CO{sub 2} storage and enhanced geothermal systems. It is concluded that despite some limitations to fully adapting a commercial code such as FLAC{sup 3D} for some specialized research and computational needs, TOUGH-FLAC is likely to remain a pragmatic simulation approach, with an increasing number of users in both academia and industry.

Study protocol: combining experimental methods, econometrics and simulation modelling to determine price elasticities for studying food taxes and subsidies (The Price ExaM Study).

Science.gov (United States)

Waterlander, Wilma E; Blakely, Tony; Nghiem, Nhung; Cleghorn, Christine L; Eyles, Helen; Genc, Murat; Wilson, Nick; Jiang, Yannan; Swinburn, Boyd; Jacobi, Liana; Michie, Jo; Ni Mhurchu, Cliona

2016-07-19

There is a need for accurate and precise food price elasticities (PE, change in consumer demand in response to change in price) to better inform policy on health-related food taxes and subsidies. The Price Experiment and Modelling (Price ExaM) study aims to: I) derive accurate and precise food PE values; II) quantify the impact of price changes on quantity and quality of discrete food group purchases and; III) model the potential health and disease impacts of a range of food taxes and subsidies. To achieve this, we will use a novel method that includes a randomised Virtual Supermarket experiment and econometric methods. Findings will be applied in simulation models to estimate population health impact (quality-adjusted life-years [QALYs]) using a multi-state life-table model. The study will consist of four sequential steps: 1. We generate 5000 price sets with random price variation for all 1412 Virtual Supermarket food and beverage products. Then we add systematic price variation for foods to simulate five taxes and subsidies: a fruit and vegetable subsidy and taxes on sugar, saturated fat, salt, and sugar-sweetened beverages. 2. Using an experimental design, 1000 adult New Zealand shoppers complete five household grocery shops in the Virtual Supermarket where they are randomly assigned to one of the 5000 price sets each time. 3. Output data (i.e., multiple observations of price configurations and purchased amounts) are used as inputs to econometric models (using Bayesian methods) to estimate accurate PE values. 4. A disease simulation model will be run with the new PE values as inputs to estimate QALYs gained and health costs saved for the five policy interventions. The Price ExaM study has the potential to enhance public health and economic disciplines by introducing internationally novel scientific methods to estimate accurate and precise food PE values. These values will be used to model the potential health and disease impacts of various food pricing policy

Study protocol: combining experimental methods, econometrics and simulation modelling to determine price elasticities for studying food taxes and subsidies (The Price ExaM Study

Directory of Open Access Journals (Sweden)

Wilma E. Waterlander

2016-07-01

Full Text Available Abstract Background There is a need for accurate and precise food price elasticities (PE, change in consumer demand in response to change in price to better inform policy on health-related food taxes and subsidies. Methods/Design The Price Experiment and Modelling (Price ExaM study aims to: I derive accurate and precise food PE values; II quantify the impact of price changes on quantity and quality of discrete food group purchases and; III model the potential health and disease impacts of a range of food taxes and subsidies. To achieve this, we will use a novel method that includes a randomised Virtual Supermarket experiment and econometric methods. Findings will be applied in simulation models to estimate population health impact (quality-adjusted life-years [QALYs] using a multi-state life-table model. The study will consist of four sequential steps: 1. We generate 5000 price sets with random price variation for all 1412 Virtual Supermarket food and beverage products. Then we add systematic price variation for foods to simulate five taxes and subsidies: a fruit and vegetable subsidy and taxes on sugar, saturated fat, salt, and sugar-sweetened beverages. 2. Using an experimental design, 1000 adult New Zealand shoppers complete five household grocery shops in the Virtual Supermarket where they are randomly assigned to one of the 5000 price sets each time. 3. Output data (i.e., multiple observations of price configurations and purchased amounts are used as inputs to econometric models (using Bayesian methods to estimate accurate PE values. 4. A disease simulation model will be run with the new PE values as inputs to estimate QALYs gained and health costs saved for the five policy interventions. Discussion The Price ExaM study has the potential to enhance public health and economic disciplines by introducing internationally novel scientific methods to estimate accurate and precise food PE values. These values will be used to model the potential

Simulation in Medical School Education: Review for Emergency Medicine

Directory of Open Access Journals (Sweden)

Shahram Lotfipour

2011-05-01

Full Text Available Medical education is rapidly evolving. With the paradigm shift to small-group didactic sessions and focus on clinically oriented case-based scenarios, simulation training has provided educators a novel way to deliver medical education in the 21st century. The field continues to expand in scope and practice and is being incorporated into medical school clerkship education, and specifically in emergency medicine (EM. The use of medical simulation in graduate medical education is well documented. Our aim in this article is to perform a retrospective review of the current literature, studying simulation use in EM medical student clerkships. Studies have demonstrated the effectiveness of simulation in teaching basic science, clinical knowledge, procedural skills, teamwork, and communication skills. As simulation becomes increasingly prevalent in medical school curricula, more studies are needed to assess whether simulation training improves patient-related outcomes.

Study of the therapeutic effects of an advanced hippotherapy simulator in children with cerebral palsy: a randomised controlled trial.

Science.gov (United States)

Herrero, Pablo; Asensio, Angel; García, Elena; Marco, Alvaro; Oliván, Barbara; Ibarz, Alejandro; Gómez-Trullén, Eva M; Casas, Roberto

2010-04-16

Although hippotherapy treatment has been demonstrated to have therapeutic effects on children with cerebral palsy, the samples used in research studies have been very small. In the case of hippotherapy simulators, there are no studies that either recommend or advise against their use in the treatment of children with cerebral palsy. The aim of this randomised clinical study is to analyse the therapeutic effects or the contraindications of the use of a commercial hippotherapy simulator on several important factors relating to children with cerebral palsy such as their motor development, balance control in the sitting posture, hip abduction range of motion and electromyographic activity of adductor musculature. The study is a randomised controlled trial. It will be carried out with a sample of 37 children with cerebral palsy divided into two treatment groups. Eligible participants will be randomly allocated to receive either (a) Treatment Group with hippotherapy simulator, maintaining sitting posture, with legs in abduction and rhythmic movement of the simulator or (b) Treatment Group maintaining sitting posture, with legs in abduction and without rhythmic movement of the simulator. all measurements will be carried out by a specially trained blind assessor. To ensure standardization quality of the assessors, an inter-examiner agreement will be worked out at the start of the study. The trial is funded by the Department of Research, Innovation and Development of the Regional Government of Aragon (Official Bulletin of Aragon 23 July 2007), project number PM059/2007. Interest in this project is due to the following factors: Clinical originality (there are no previous studies analysing the effect of simulators on the population group of children with CP, nor any studies using as many variables as this project); Clinical impact (infantile cerebral palsy is a chronic multisystemic condition that affects not only the patient but also the patient's family and their close

A Study of the Use of Simulations and Games in Education with Special Reference to Geography.

Science.gov (United States)

O'Reilly, Desmond Vincent

Chapter 1 of this thesis provides definitions of terms used. Chapter 2 discusses role-playing, strategy games, and models. Chapter 3 explores the significance of games in child development. Chapter 4 relates the historical development of gaming and simulation. Chapter 5 focuses on advantages of simulations and games in education in terms of such…

Virtual Learning Simulations in High School

DEFF Research Database (Denmark)

Thisgaard, Malene Warming; Makransky, Guido

2017-01-01

The present study compared the value of using a virtual learning simulation compared to traditional lessons on the topic of evolution, and investigated if the virtual learning simulation could serve as a catalyst for STEM academic and career development, based on social cognitive career theory....... The investigation was conducted using a crossover repeated measures design based on a sample of 128 high school biology/biotech students. The results showed that the virtual learning simulation increased knowledge of evolution significantly, compared to the traditional lesson. No significant differences between...... the simulation and lesson were found in their ability to increase the non-cognitive measures. Both interventions increased self-efficacy significantly, and none of them had a significant effect on motivation. In addition, the results showed that the simulation increased interest in biology related tasks...

Transferring Nuclear Knowledge by NPP Simulators Developers

International Nuclear Information System (INIS)

Levchenko, A.; Duginov, O.; Levchenko, V.

2016-01-01

Full text: In relation to nuclear power, safety is closely linked with the human factor. Knowledge and skills of staff should more closely match the needs of the industry and employers. This can be achieved through more efficient training using simulators. Such simulators must be available at all stages of study and cover the needs of trainees with different levels of knowledge. Simulator developers can solve this problem by implement knowledge management in the using of simulators for practical training. Due to the nature of their activities, they have everything needed for this. This paper describes the solutions of Simulation Systems Ltd Company for nuclear power plants, universities and other parties. (author

Driving simulator sickness: Impact on driving performance, influence of blood alcohol concentration, and effect of repeated simulator exposures.

Science.gov (United States)

Helland, Arne; Lydersen, Stian; Lervåg, Lone-Eirin; Jenssen, Gunnar D; Mørland, Jørg; Slørdal, Lars

2016-09-01

Simulator sickness is a major obstacle to the use of driving simulators for research, training and driver assessment purposes. The purpose of the present study was to investigate the possible influence of simulator sickness on driving performance measures such as standard deviation of lateral position (SDLP), and the effect of alcohol or repeated simulator exposure on the degree of simulator sickness. Twenty healthy male volunteers underwent three simulated driving trials of 1h's duration with a curvy rural road scenario, and rated their degree of simulator sickness after each trial. Subjects drove sober and with blood alcohol concentrations (BAC) of approx. 0.5g/L and 0.9g/L in a randomized order. Simulator sickness score (SSS) did not influence the primary outcome measure SDLP. Higher SSS significantly predicted lower average speed and frequency of steering wheel reversals. These effects seemed to be mitigated by alcohol. Higher BAC significantly predicted lower SSS, suggesting that alcohol inebriation alleviates simulator sickness. The negative relation between the number of previous exposures to the simulator and SSS was not statistically significant, but is consistent with habituation to the sickness-inducing effects, as shown in other studies. Overall, the results suggest no influence of simulator sickness on SDLP or several other driving performance measures. However, simulator sickness seems to cause test subjects to drive more carefully, with lower average speed and fewer steering wheel reversals, hampering the interpretation of these outcomes as measures of driving impairment and safety. BAC and repeated simulator exposures may act as confounding variables by influencing the degree of simulator sickness in experimental studies. Copyright © 2016 Elsevier Ltd. All rights reserved.

Self-Radiolysis of Tritiated Water: Experimental Study and Simulation

International Nuclear Information System (INIS)

Heinze, Sylver; Stolz, Thibaut; Ducret, Didier; Colson, Jean-Claude

2005-01-01

Radioactive decay of tritium contained in tritiated water leads to the production of gaseous helium and, through self-radiolysis, to the formation of molecular hydrogen and oxygen. For safety management of tritiated water storage, it is essential to be able to predict pressure increase resulting from this phenomenon. The present study aims to identify the mechanisms that take place in self-radiolysis of chemically pure liquid tritiated water. The evolution of the concentration of hydrogen and oxygen in the gas phase of closed vessels containing tritiated water has been followed experimentally. Simulation of pure water radiolysis has been carried out using data from the literature. In order to fit experimental results, simulation should take into account gas phase recombination reaction between hydrogen and oxygen. A simplified system has been extracted from the complete chemical system used to simulate radiolysis. This system allows identifying the basic mechanisms that are responsible for tritiated water self-radiolysis

Monte Carlo Simulations Validation Study: Vascular Brachytherapy Beta Sources

International Nuclear Information System (INIS)

Orion, I.; Koren, K.

2004-01-01

During the last decade many versions of angioplasty irradiation treatments have been proposed. The purpose of this unique brachytherapy is to administer a sufficient radiation dose into the vein walls in order to prevent restonosis, a clinical sequel to balloon angioplasty. The most suitable sources for this vascular brachytherapy are the β - emitters such as Re-188, P-32, and Sr-90/Y-90, with a maximum energy range of up to 2.1 MeV [1,2,3]. The radioactive catheters configurations offered for these treatments can be a simple wire [4], a fluid filled balloon or a coated stent. Each source is differently positioned inside the blood vessel, and the emitted electrons ranges therefore vary. Many types of sources and configurations were studied either experimentally or with the use of the Monte Carlo calculation technique, while most of the Monte Carlo simulations were carried out using EGS4 [5] or MCNP [6]. In this study we compared the beta-source absorbed-dose versus radial-distance of two treatment configurations using MCNP and EGS4 simulations. This comparison was aimed to discover the differences between the MCNP and the EGS4 simulation code systems in intermediate energies electron transport

Simulating a base population in honey bee for molecular genetic studies.

Science.gov (United States)

Gupta, Pooja; Conrad, Tim; Spötter, Andreas; Reinsch, Norbert; Bienefeld, Kaspar

2012-06-27

Over the past years, reports have indicated that honey bee populations are declining and that infestation by an ecto-parasitic mite (Varroa destructor) is one of the main causes. Selective breeding of resistant bees can help to prevent losses due to the parasite, but it requires that a robust breeding program and genetic evaluation are implemented. Genomic selection has emerged as an important tool in animal breeding programs and simulation studies have shown that it yields more accurate breeding value estimates, higher genetic gain and low rates of inbreeding. Since genomic selection relies on marker data, simulations conducted on a genomic dataset are a pre-requisite before selection can be implemented. Although genomic datasets have been simulated in other species undergoing genetic evaluation, simulation of a genomic dataset specific to the honey bee is required since this species has a distinct genetic and reproductive biology. Our software program was aimed at constructing a base population by simulating a random mating honey bee population. A forward-time population simulation approach was applied since it allows modeling of genetic characteristics and reproductive behavior specific to the honey bee. Our software program yielded a genomic dataset for a base population in linkage disequilibrium. In addition, information was obtained on (1) the position of markers on each chromosome, (2) allele frequency, (3) χ(2) statistics for Hardy-Weinberg equilibrium, (4) a sorted list of markers with a minor allele frequency less than or equal to the input value, (5) average r(2) values of linkage disequilibrium between all simulated marker loci pair for all generations and (6) average r2 value of linkage disequilibrium in the last generation for selected markers with the highest minor allele frequency. We developed a software program that takes into account the genetic and reproductive biology specific to the honey bee and that can be used to constitute a genomic

A Study on Bipedal and Mobile Robot Behavior Through Modeling and Simulation

Directory of Open Access Journals (Sweden)

Nirmala Nirmala

2015-05-01

Full Text Available The purpose of this work is to study and analyze mobile robot behavior. In performing this, a framework is adopted and developed for mobile and bipedal robot. The robots are design, build, and run as proceed from the development of mechanical structure, electronics and control integration, and control software application. The behavior of those robots are difficult to be observed and analyzed qualitatively. To evaluate the design and behavior quality, modeling and simulation of robot structure and its task capability is performed. The stepwise procedure to robot behavior study is explained. Behavior cases study are experimented to bipedal robots, transporter robot and Autonomous Guided Vehicle (AGV developed at our institution. The experimentation are conducted on those robots by adjusting their dynamic properties and/or surrounding environment. Validation is performed by comparing the simulation result and the real robot execution. The simulation gives a more idealistic behavior execution rather than realistic one. Adjustments are performed to fine tuning simulation's parameters to provide a more realistic performance.

Study on efficiency of time computation in x-ray imaging simulation base on Monte Carlo algorithm using graphics processing unit

International Nuclear Information System (INIS)

Setiani, Tia Dwi; Suprijadi; Haryanto, Freddy

2016-01-01

Monte Carlo (MC) is one of the powerful techniques for simulation in x-ray imaging. MC method can simulate the radiation transport within matter with high accuracy and provides a natural way to simulate radiation transport in complex systems. One of the codes based on MC algorithm that are widely used for radiographic images simulation is MC-GPU, a codes developed by Andrea Basal. This study was aimed to investigate the time computation of x-ray imaging simulation in GPU (Graphics Processing Unit) compared to a standard CPU (Central Processing Unit). Furthermore, the effect of physical parameters to the quality of radiographic images and the comparison of image quality resulted from simulation in the GPU and CPU are evaluated in this paper. The simulations were run in CPU which was simulated in serial condition, and in two GPU with 384 cores and 2304 cores. In simulation using GPU, each cores calculates one photon, so, a large number of photon were calculated simultaneously. Results show that the time simulations on GPU were significantly accelerated compared to CPU. The simulations on the 2304 core of GPU were performed about 64 -114 times faster than on CPU, while the simulation on the 384 core of GPU were performed about 20 – 31 times faster than in a single core of CPU. Another result shows that optimum quality of images from the simulation was gained at the history start from 10"8 and the energy from 60 Kev to 90 Kev. Analyzed by statistical approach, the quality of GPU and CPU images are relatively the same.

Study on efficiency of time computation in x-ray imaging simulation base on Monte Carlo algorithm using graphics processing unit

Energy Technology Data Exchange (ETDEWEB)

Setiani, Tia Dwi, E-mail: tiadwisetiani@gmail.com [Computational Science, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung Jalan Ganesha 10 Bandung, 40132 (Indonesia); Suprijadi [Computational Science, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung Jalan Ganesha 10 Bandung, 40132 (Indonesia); Nuclear Physics and Biophysics Reaserch Division, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung Jalan Ganesha 10 Bandung, 40132 (Indonesia); Haryanto, Freddy [Nuclear Physics and Biophysics Reaserch Division, Faculty of Mathematics and Natural Sciences, Institut Teknologi Bandung Jalan Ganesha 10 Bandung, 40132 (Indonesia)

2016-03-11

Monte Carlo (MC) is one of the powerful techniques for simulation in x-ray imaging. MC method can simulate the radiation transport within matter with high accuracy and provides a natural way to simulate radiation transport in complex systems. One of the codes based on MC algorithm that are widely used for radiographic images simulation is MC-GPU, a codes developed by Andrea Basal. This study was aimed to investigate the time computation of x-ray imaging simulation in GPU (Graphics Processing Unit) compared to a standard CPU (Central Processing Unit). Furthermore, the effect of physical parameters to the quality of radiographic images and the comparison of image quality resulted from simulation in the GPU and CPU are evaluated in this paper. The simulations were run in CPU which was simulated in serial condition, and in two GPU with 384 cores and 2304 cores. In simulation using GPU, each cores calculates one photon, so, a large number of photon were calculated simultaneously. Results show that the time simulations on GPU were significantly accelerated compared to CPU. The simulations on the 2304 core of GPU were performed about 64 -114 times faster than on CPU, while the simulation on the 384 core of GPU were performed about 20 – 31 times faster than in a single core of CPU. Another result shows that optimum quality of images from the simulation was gained at the history start from 10{sup 8} and the energy from 60 Kev to 90 Kev. Analyzed by statistical approach, the quality of GPU and CPU images are relatively the same.

Temperature dependence of creep compliance of highly cross-linked epoxy: A molecular simulation study

International Nuclear Information System (INIS)

Khabaz, Fardin; Khare, Ketan S.; Khare, Rajesh

2014-01-01

We have used molecular dynamics (MD) simulations to study the effect of temperature on the creep compliance of neat cross-linked epoxy. Experimental studies of mechanical behavior of cross-linked epoxy in literature commonly report creep compliance values, whereas molecular simulations of these systems have primarily focused on the Young’s modulus. In this work, in order to obtain a more direct comparison between experiments and simulations, atomistically detailed models of the cross-linked epoxy are used to study their creep compliance as a function of temperature using MD simulations. The creep tests are performed by applying a constant tensile stress and monitoring the resulting strain in the system. Our results show that simulated values of creep compliance increase with an increase in both time and temperature. We believe that such calculations of the creep compliance, along with the use of time temperature superposition, hold great promise in connecting the molecular insight obtained from molecular simulation at small length- and time-scales with the experimental behavior of such materials. To the best of our knowledge, this work is the first reported effort that investigates the creep compliance behavior of cross-linked epoxy using MD simulations

Friction between Two Brownian Particles in a Lennard-Jones Solvent: A Molecular Dynamics Simulation Study

International Nuclear Information System (INIS)

Lee, Song Hi

2010-01-01

We presented a molecular dynamics (MD) simulation study of friction behavior between two very massive Brownian particles (BPs) oriented along the z axis with BP centers at -R 12 /2 and R 12 /2 in a Lennard-Jones solvent as a function of the inter-particle separation, R 12 . In order to fix the BPs in space an MD simulation method with the mass of the BP as 10 90 g/mol was employed in which the total momentum of the system was conserved. The cross friction coefficients of x- and y-components are nearly insensitive to R 12 but that of z-component varies with R 12 in good accord with the simple hydrodynamic approximation. On the other hand, the self-friction coefficients are estimated as a very small difference from the single particle friction coefficients, ξ 0 , at all inter-particle separations which agrees with the simple hydrodynamic approximation. Consequently ξ (-) xx is nearly independent of R 12 and equal to its asymptotic value of twice the single particle friction coefficient, and the other relative friction, ξ (-) zz , is in good agreement with the simple hydrodynamic approximation. Molecular theory of Brownian motion of a single heavy particle in a fluid had received a considerable attention in earlier years. After molecular dynamics (MD) simulation technique was utilized, this subject has been widely studied by a variety of MD simulation methods. The common issues here were about the long time behavior of the force and velocity autocorrelation functions, the system size dependent friction coefficient of a massive Brownian particle, and test of the Stokes-Einstein law

Virtual Property Manager: Providing a Simulated Learning Environment in a New University Program of Study

Directory of Open Access Journals (Sweden)

Andrew Carswell

2007-08-01

Full Text Available This paper relates the experience that students have while accessing Virtual Property Manager (VPM, a Web-based simulation learning tool designed to introduce students to a new discipline being offered at the university – Residential Property Management. The VPM simulation was designed in part to develop student interest in the new program. Results indicate that this simple simulation device did make a notable impact on student interest. Additionally, student acceptance and self-reported impact differed significantly based upon the delivery context. Adding a competitive reward element to the simulation experience improved student's evaluation of the software and self-reported interest in the field. Results indicate that educational simulation evaluation, acceptance, and performance may often be substantially influenced by the delivery context, rather than simply the program itself. Developers may do well to focus "outside the box" of program content to promote audience-specific delivery environments.

Influence of thyroid volume reduction on absorbed dose in "1"3"1I therapy studied by using Geant4 Monte Carlo simulation

International Nuclear Information System (INIS)

Rahman, Ziaur; Arshed, Waheed; Ahmed, Waheed; Mirza, Sikander M.; Mirza, Nasir M.

2014-01-01

A simulation study has been performed to quantify the effect of volume reduction on the thyroid absorbed dose per decay and to investigate the variation of energy deposition per decay due to β- and γ-activity of "1"3"1I with volume/mass of thyroid, for water, ICRP- and ICRU-soft tissue taken as thyroid material. A Monte Carlo model of the thyroid, in the Geant4 radiation transport simulation toolkit was constructed to compute the β- and γ-absorbed dose in the simulated thyroid phantom for various values of its volume. The effect of the size and shape of the thyroid on energy deposition per decay has also been studied by using spherical, ellipsoidal and cylindrical models for the thyroid and varying its volume in 1-25 cm"3 range. The relative differences of Geant4 results for different models with each other and MCNP results lie well below 1.870%. The maximum relative difference among the Geant4 estimated results for water with ICRP and ICRU soft tissues is not more than 0.225%. S-values for ellipsoidal, spherical and cylindrical thyroid models were estimated and the relative difference with published results lies within 3.095%. The absorbed fraction values for beta particles show a good agreement with published values within 2.105% deviation. The Geant4 based simulation results of absorbed fractions for gammas again show a good agreement with the corresponding MCNP and EGS4 results (± 6.667%) but have 29.032% higher values than that of MIRD calculated values. Consistent with previous studies, the reduction of the thyroid volume is found to have a substantial effect on the absorbed dose. Geant4 simulations confirm dose dependence on the volume/mass of thyroid in agreement with MCNP and EGS4 computed values but are substantially different from MIRD8 data. Therefore, inclusion of size/mass dependence is indicated for "1"3"1I radiotherapy of the thyroid. (authors)

CO2 capture using aqueous ammonia: kinetic study and process simulation

DEFF Research Database (Denmark)

Darde, Victor Camille Alfred; van Well, Willy J.M.; Stenby, Erling Halfdan

2011-01-01

to 0.6. The results were compared with those found for 30 wt% mono-ethanolamine (MEA) solutions.The capture process was simulated successfully using the simulator Aspen Plus coupled with the extended UNIQUAC thermodynamic model available for the NH3–CO2–H2O system. For this purpose, a user model......Carbon dioxide capture using aqueous ammonia is a post-combustion technology that has shown a good potential. Therefore this process is studied by measuring the rate of absorption of carbon dioxide by aqueous ammonia and by performing process simulation. The rate of absorption of carbon dioxide...

Bias, precision and statistical power of analysis of covariance in the analysis of randomized trials with baseline imbalance: a simulation study

Science.gov (United States)

2014-01-01

Background Analysis of variance (ANOVA), change-score analysis (CSA) and analysis of covariance (ANCOVA) respond differently to baseline imbalance in randomized controlled trials. However, no empirical studies appear to have quantified the differential bias and precision of estimates derived from these methods of analysis, and their relative statistical power, in relation to combinations of levels of key trial characteristics. This simulation study therefore examined the relative bias, precision and statistical power of these three analyses using simulated trial data. Methods 126 hypothetical trial scenarios were evaluated (126 000 datasets), each with continuous data simulated by using a combination of levels of: treatment effect; pretest-posttest correlation; direction and magnitude of baseline imbalance. The bias, precision and power of each method of analysis were calculated for each scenario. Results Compared to the unbiased estimates produced by ANCOVA, both ANOVA and CSA are subject to bias, in relation to pretest-posttest correlation and the direction of baseline imbalance. Additionally, ANOVA and CSA are less precise than ANCOVA, especially when pretest-posttest correlation ≥ 0.3. When groups are balanced at baseline, ANCOVA is at least as powerful as the other analyses. Apparently greater power of ANOVA and CSA at certain imbalances is achieved in respect of a biased treatment effect. Conclusions Across a range of correlations between pre- and post-treatment scores and at varying levels and direction of baseline imbalance, ANCOVA remains the optimum statistical method for the analysis of continuous outcomes in RCTs, in terms of bias, precision and statistical power. PMID:24712304

3D simulation studies of tokamak plasmas using MHD and extended-MHD models

International Nuclear Information System (INIS)

Park, W.; Chang, Z.; Fredrickson, E.; Fu, G.Y.; Pomphrey, N.; Sugiyama, L.E.

1997-01-01

The M3D (Multi-level 3D) tokamak simulation project aims at the simulation of tokamak plasmas using a multi-level tokamak code package. Several current applications using MHD and Extended-MHD models are presented; high-β disruption studies in reversed shear plasmas using the MHD level MH3D code, ω *i stabilization and nonlinear island rotation studies using the two-fluid level MH3D-T code, studies of nonlinear saturation of TAE modes using the hybrid particle/MHD level MH3D-K code, and unstructured mesh MH3D ++ code studies. In particular, three internal mode disruption mechanisms are identified from simulation results which agree well with experimental data

Lipopolysaccharide Membranes and Membrane Proteins of Pseudomonas aeruginosa Studied by Computer Simulation

Energy Technology Data Exchange (ETDEWEB)

Straatsma, TP

2006-12-01

Pseudomonas aeruginosa is a ubiquitous environmental Gram-negative bacterium with high metabolic versatility and an exceptional ability to adapt to a wide range of ecological environments, including soil, marches, coastal habitats, plant and animal tissues. Gram-negative microbes are characterized by the asymmetric lipopolysaccharide outer membrane, the study of which is important for a number of applications. The adhesion to mineral surfaces plays a central role in characterizing their contribution to the fate of contaminants in complex environmental systems by effecting microbial transport through soils, respiration redox chemistry, and ion mobility. Another important application stems from the fact that it is also a major opportunistic human pathogen that can result in life-threatening infections in many immunocompromised patients, such as lung infections in children with cystic fibrosis, bacteraemia in burn victims, urinary-tract infections in catheterized patients, hospital-acquired pneumonia in patients on respirators, infections in cancer patients receiving chemotherapy, and keratitis and corneal ulcers in users of extended-wear soft contact lenses. The inherent resistance against antibiotics which has been linked with the specific interactions in the outer membrane of P. aeruginosa makes these infections difficult to treat. Developments in simulation methodologies as well as computer hardware have enabled the molecular simulation of biological systems of increasing size and with increasing accuracy, providing detail that is difficult or impossible to obtain experimentally. Computer simulation studies contribute to our understanding of the behavior of proteins, protein-protein and protein-DNA complexes. In recent years, a number of research groups have made significant progress in applying these methods to the study of biological membranes. However, these applications have been focused exclusively on lipid bilayer membranes and on membrane proteins in lipid

Strategic approaches to simulation-based education: A case study from Australia

Directory of Open Access Journals (Sweden)

Debra Nestel

2013-01-01

Full Text Available This paper addresses some of the challenges met when developing widely distributed, broad spectrum, simulation-based education (SBE for health professionals, such as resource duplication, inconsistent facilities utilization, discipline-specific silos, and the intersection of academic institutions and health services sectors. We examine three primary contributors to successful simulation-based practices - strategic planning, program development, and professional networks. Further, we provide examples of how each of these contributors function at different levels to assure comprehensive, yet sustainable approaches to implementing SBE for greatest impact at national, state, regional, and institutional levels. We draw on the example of Australia and its state and regional government structures, including the challenges in providing health services across a widely variable geography and population distribution. The types of health services and issues relating to health provision and management reflect those found in many western countries. Our hope is that the experiences gained at each level of governance within Australia may inform similar, successful development in other countries. We emphasize the importance of leadership and investment at the national level that serves to inform state, regional, and institutional efforts through a "trickle down" effect. Although evaluation of the strategic planning, program development, and professional networks described in this case study is still ongoing, their preliminary coordination has resulted in significant investment and support at all levels.

A Novel Simulation Technician Laboratory Design: Results of a Survey-Based Study.

Science.gov (United States)

Ahmed, Rami; Hughes, Patrick G; Friedl, Ed; Ortiz Figueroa, Fabiana; Cepeda Brito, Jose R; Frey, Jennifer; Birmingham, Lauren E; Atkinson, Steven Scott

2016-03-16

OBJECTIVE : The purpose of this study was to elicit feedback from simulation technicians prior to developing the first simulation technician-specific simulation laboratory in Akron, OH. Simulation technicians serve a vital role in simulation centers within hospitals/health centers around the world. The first simulation technician degree program in the US has been approved in Akron, OH. To satisfy the requirements of this program and to meet the needs of this special audience of learners, a customized simulation lab is essential. A web-based survey was circulated to simulation technicians prior to completion of the lab for the new program. The survey consisted of questions aimed at identifying structural and functional design elements of a novel simulation center for the training of simulation technicians. Quantitative methods were utilized to analyze data. Over 90% of technicians (n=65) think that a lab designed explicitly for the training of technicians is novel and beneficial. Approximately 75% of respondents think that the space provided appropriate audiovisual (AV) infrastructure and space to evaluate the ability of technicians to be independent. The respondents think that the lab needed more storage space, visualization space for a large number of students, and more space in the technical/repair area. CONCLUSIONS : A space designed for the training of simulation technicians was considered to be beneficial. This laboratory requires distinct space for technical repair, adequate bench space for the maintenance and repair of simulators, an appropriate AV infrastructure, and space to evaluate the ability of technicians to be independent.

Corrosion Inhibition Study of Al-Cu-Ni Alloy in Simulated Sea-Water ...

African Journals Online (AJOL)

Akorede

ABSTRACT: A study on the inhibition of Al-Cu-Ni alloy in simulated ... which the percentage of Copper, and Nickel were kept .... proceed based on equation of reaction in eqn (4). Al .... Sodium-Modified A356.0-Type Al-Si-Mg Alloy in Simulated.

Simulation of complex data structures for planning of studies with focus on biomarker comparison.

Science.gov (United States)

Schulz, Andreas; Zöller, Daniela; Nickels, Stefan; Beutel, Manfred E; Blettner, Maria; Wild, Philipp S; Binder, Harald

2017-06-13

There are a growing number of observational studies that do not only focus on single biomarkers for predicting an outcome event, but address questions in a multivariable setting. For example, when quantifying the added value of new biomarkers in addition to established risk factors, the aim might be to rank several new markers with respect to their prediction performance. This makes it important to consider the marker correlation structure for planning such a study. Because of the complexity, a simulation approach may be required to adequately assess sample size or other aspects, such as the choice of a performance measure. In a simulation study based on real data, we investigated how to generate covariates with realistic distributions and what generating model should be used for the outcome, aiming to determine the least amount of information and complexity needed to obtain realistic results. As a basis for the simulation a large epidemiological cohort study, the Gutenberg Health Study was used. The added value of markers was quantified and ranked in subsampling data sets of this population data, and simulation approaches were judged by the quality of the ranking. One of the evaluated approaches, the random forest, requires original data at the individual level. Therefore, also the effect of the size of a pilot study for random forest based simulation was investigated. We found that simple logistic regression models failed to adequately generate realistic data, even with extensions such as interaction terms or non-linear effects. The random forest approach was seen to be more appropriate for simulation of complex data structures. Pilot studies starting at about 250 observations were seen to provide a reasonable level of information for this approach. We advise to avoid oversimplified regression models for simulation, in particular when focusing on multivariable research questions. More generally, a simulation should be based on real data for adequately reflecting

Simulation of complex data structures for planning of studies with focus on biomarker comparison

Directory of Open Access Journals (Sweden)

Andreas Schulz

2017-06-01

Full Text Available Abstract Background There are a growing number of observational studies that do not only focus on single biomarkers for predicting an outcome event, but address questions in a multivariable setting. For example, when quantifying the added value of new biomarkers in addition to established risk factors, the aim might be to rank several new markers with respect to their prediction performance. This makes it important to consider the marker correlation structure for planning such a study. Because of the complexity, a simulation approach may be required to adequately assess sample size or other aspects, such as the choice of a performance measure. Methods In a simulation study based on real data, we investigated how to generate covariates with realistic distributions and what generating model should be used for the outcome, aiming to determine the least amount of information and complexity needed to obtain realistic results. As a basis for the simulation a large epidemiological cohort study, the Gutenberg Health Study was used. The added value of markers was quantified and ranked in subsampling data sets of this population data, and simulation approaches were judged by the quality of the ranking. One of the evaluated approaches, the random forest, requires original data at the individual level. Therefore, also the effect of the size of a pilot study for random forest based simulation was investigated. Results We found that simple logistic regression models failed to adequately generate realistic data, even with extensions such as interaction terms or non-linear effects. The random forest approach was seen to be more appropriate for simulation of complex data structures. Pilot studies starting at about 250 observations were seen to provide a reasonable level of information for this approach. Conclusions We advise to avoid oversimplified regression models for simulation, in particular when focusing on multivariable research questions. More generally

WRF simulation of a severe hailstorm over Baramati: a study into the space-time evolution

Science.gov (United States)

Murthy, B. S.; Latha, R.; Madhuparna, H.

2018-04-01

Space-time evolution of a severe hailstorm occurred over the western India as revealed by WRF-ARW simulations are presented. We simulated a specific event centered over Baramati (18.15°N, 74.58°E, 537 m AMSL) on March 9, 2014. A physical mechanism, proposed as a conceptual model, signifies the role of multiple convective cells organizing through outflows leading to a cold frontal type flow, in the presence of a low over the northern Arabian Sea, propagates from NW to SE triggering deep convection and precipitation. A `U' shaped cold pool encircled by a converging boundary forms to the north of Baramati due to precipitation behind the moisture convergence line with strong updrafts ( 15 ms-1) leading to convective clouds extending up to 8 km in a narrow region of 30 km. The outflows from the convective clouds merge with the opposing southerly or southwesterly winds from the Arabian Sea and southerly or southeasterly winds from the Bay of Bengal resulting in moisture convergence (maximum 80 × 10-3 g kg-1 s-1). The vertical profile of the area-averaged moisture convergence over the cold pool shows strong convergence above 850 hPa and divergence near the surface indicating elevated convection. Radar reflectivity (50-60 dBZ) and vertical component of vorticity maximum ( 0.01-0.14 s-1) are observed along the convergence zone. Stratiform clouds ahead of the squall line and parallel wind flow at 850 hPa and nearly perpendicular flow at higher levels relative to squall line as evidenced by relatively low and wide-spread reflectivity suggests that organizational mode of squall line may be categorized as `Mixed Mode' type where northern part can be a parallel stratiform while the southern part resembles with a leading stratiform. Simulated rainfall (grid scale 27 km) leads the observed rainfall by 1 h while its magnitude is 2 times of the observed rainfall (grid scale 100 km) derived from Kalpana-1. Thus, this study indicates that under synoptically favorable conditions

A Pilot Study Assessing Performance and Visual Attention of Teenagers with ASD in a Novel Adaptive Driving Simulator.

Science.gov (United States)

Wade, Joshua; Weitlauf, Amy; Broderick, Neill; Swanson, Amy; Zhang, Lian; Bian, Dayi; Sarkar, Medha; Warren, Zachary; Sarkar, Nilanjan

2017-11-01

Individuals with Autism Spectrum Disorder (ASD), compared to typically-developed peers, may demonstrate behaviors that are counter to safe driving. The current work examines the use of a novel simulator in two separate studies. Study 1 demonstrates statistically significant performance differences between individuals with (N = 7) and without ASD (N = 7) with regards to the number of turning-related driving errors (p training (p attention of drivers and an adaptive driving intervention for individuals with ASD.

Simulation Activity in Otolaryngology Residencies.

Science.gov (United States)

Deutsch, Ellen S; Wiet, Gregory J; Seidman, Michael; Hussey, Heather M; Malekzadeh, Sonya; Fried, Marvin P

2015-08-01

Simulation has become a valuable tool in medical education, and several specialties accept or require simulation as a resource for resident training or assessment as well as for board certification or maintenance of certification. This study investigates current simulation resources and activities in US otolaryngology residency programs and examines interest in advancing simulation training and assessment within the specialty. Web-based survey. US otolaryngology residency training programs. An electronic web-based survey was disseminated to all US otolaryngology program directors to determine their respective institutional and departmental simulation resources, existing simulation activities, and interest in further simulation initiatives. Descriptive results are reported. Responses were received from 43 of 104 (43%) residency programs. Simulation capabilities and resources are available in most respondents' institutions (78.6% report onsite resources; 73.8% report availability of models, manikins, and devices). Most respondents (61%) report limited simulation activity within otolaryngology. Areas of simulation are broad, addressing technical and nontechnical skills related to clinical training (94%). Simulation is infrequently used for research, credentialing, or systems improvement. The majority of respondents (83.8%) expressed interest in participating in multicenter trials of simulation initiatives. Most respondents from otolaryngology residency programs have incorporated some simulation into their curriculum. Interest among program directors to participate in future multicenter trials appears high. Future research efforts in this area should aim to determine optimal simulators and simulation activities for training and assessment as well as how to best incorporate simulation into otolaryngology residency training programs. © American Academy of Otolaryngology—Head and Neck Surgery Foundation 2015.

Simulation of dust-acoustic waves

International Nuclear Information System (INIS)

Winske, D.; Murillo, M.S.; Rosenberg, M.

1998-01-01

The authors use molecular dynamics (MD) and particle-in-cell (PIC) simulation methods to investigate the dispersion relation of dust-acoustic waves in a one-dimensional, strongly coupled (Coulomb coupling parameter Λ = ratio of the Coulomb energy to the thermal energy = 120) dusty plasma. They study both cases where the dust is represented by a small number of simulation particles that form into a regular array structure (crystal limit) as well as where the dust is represented by a much larger number of particles (fluid limit)

Simulation studies on high-gradient experiments

International Nuclear Information System (INIS)

Yamaguchi, S.

1992-12-01

Computer simulation of the characteristics of the dark current emitted from a 0.6 m long S-band accelerating structure has been made. The energy spectra and the dependence of the dark current on the structure length were simulated. By adjusting the secondary electron emission (SEE) coefficients, the simulated energy spectra qualitatively reproduced the observed ones. It was shown that the dark current increases exponentially with the structure length. The measured value of the multiplication factor of the dark current per unit cell can be explained if the SEE coefficient is set to 1.2. The critical gradient for dark current capture E cri has been calculated for two structures of 180 cells. They are E cri [MV/m] = 13.1 f and 8.75 f for a/λ = 0.089 and 0.16, respectively, where f is the frequency in GHz, a the iris diameter and λ the wave length

EXAMINATION OF THE SIMULATED THERMAL CONDITIONS IN A POPULAR PLAYGROUND RELATED TO THE HUMAN REACTIONS AND THE JUDGMENT OF THE AREA DESIGN

Directory of Open Access Journals (Sweden)

L.A. ÉGERHÁZI

2013-03-01

Full Text Available In the field of urban bioclimatology an important and timely research direction today is to examine the thermal conditions of public places. In our study, human thermal comfort analysis was performed in a modern and well-attended children playground located in Szeged (Hungary. The aim of the paper is to reveal the changes in the thermal comfort conditions between two seasons and also the resulting subjective thermal reactions of visitors in this relatively small area. Thermal comfort conditions were quantified by the Physiologically Equivalent Temperature (PET. For typical summer and autumn days of 2011 numerical simulations of thermal comfort conditions in the playground were carried out by means of the urban microclimate model ENVI-met. Spatial distribution of the simulated PET, i.e. thermal stress maps were created in two different times of the selected days in order to characterize the distinct microclimatological conditions appearing in the area. The relationship between the momentary spatial patterns of visitors and the thermal conditions was also under investigation. Additionally, onsite questionnaire survey was implemented which highlights the people’s subjective evaluation related to the design of the playground.

Thermal inertia and energy efficiency – Parametric simulation assessment on a calibrated case study

International Nuclear Information System (INIS)

Aste, Niccolò; Leonforte, Fabrizio; Manfren, Massimiliano; Mazzon, Manlio

2015-01-01

Highlights: • We perform a parametric simulation study on a calibrated building energy model. • We introduce adaptive shadings and night free cooling in simulations. • We analyze the effect of thermal capacity on the parametric simulations results. • We recognize that cooling demand and savings scales linearly with thermal capacity. • We assess the advantage of medium-heavy over medium and light configurations. - Abstract: The reduction of energy consumption for heating and cooling services in the existing building stock is a key challenge for global sustainability today and buildings’ envelopes retrofit is one the main issues. Most of the existing buildings’ envelopes have low levels of insulation, high thermal losses due to thermal bridges and cracks, absence of appropriate solar control, etc. Further, in building refurbishment, the importance of a system level approach is often undervalued in favour of simplistic “off the shelf” efficient solutions, focused on the reduction of thermal transmittance and on the enhancement of solar control capabilities. In many cases, the importance of the dynamic thermal properties is often neglected or underestimated and the effective thermal capacity is not properly considered as one of the design parameters. The research presented aims to critically assess the influence of the dynamic thermal properties of the building fabric (roof, walls and floors) on sensible heating and cooling energy demand for a case study. The case study chosen is an existing office building which has been retrofitted in recent years and whose energy model has been calibrated according to the data collected in the monitoring process. The research illustrates the variations of the sensible thermal energy demand of the building in different retrofit scenarios, and relates them to the variations of the dynamic thermal properties of the construction components. A parametric simulation study has been performed, encompassing the use of

Reprocessing process simulation network; PRONET

International Nuclear Information System (INIS)

Mitsui, T.; Takada, H.; Kamishima, N.; Tsukamoto, T.; Harada, N.; Fujita, N.; Gonda, K.

1991-01-01

The effectiveness of simulation technology and its wide application to nuclear fuel reprocessing plants has been recognized recently. The principal aim of applying simulation is to predict the process behavior accurately based on the quantitative relations among substances in physical and chemical phenomena. Mitsubishi Heavy Industries Ltd. has engaged positively in the development and the application study of this technology. All the software products of its recent activities were summarized in the integrated form named 'PRONET'. The PRONET is classified into two independent software groups from the viewpoint of computer system. One is off-line Process Simulation Group, and the other is Dynamic Real-time Simulator Group. The former is called 'PRONET System', and the latter is called 'PRONET Simulator'. These have several subsystems with the prefix 'MR' meaning Mitsubishi Reprocessing Plant. Each MR subsystem is explained in this report. The technical background, the objective of the PRONET, the system and the function of the PRONET, and the future application to an on-line real-time simulator and the development of MR EXPERT are described. (K.I.)

Using Computer Simulations for Investigating a Sex Education Intervention: An Exploratory Study.

Science.gov (United States)

Eleftheriou, Anastasia; Bullock, Seth; Graham, Cynthia A; Ingham, Roger

2017-05-03

Sexually transmitted infections (STIs) are ongoing concerns. The best method for preventing the transmission of these infections is the correct and consistent use of condoms. Few studies have explored the use of games in interventions for increasing condom use by challenging the false sense of security associated with judging the presence of an STI based on attractiveness. The primary purpose of this study was to explore the potential use of computer simulation as a serious game for sex education. Specific aims were to (1) study the influence of a newly designed serious game on self-rated confidence for assessing STI risk and (2) examine whether this varied by gender, age, and scores on sexuality-related personality trait measures. This paper undertook a Web-based questionnaire study employing between and within subject analyses. A Web-based platform hosted in the United Kingdom was used to deliver male and female stimuli (facial photographs) and collect data. A convenience sample group of 66 participants (64%, 42/66) male, mean age 22.5 years) completed the Term on the Tides, a computer simulation developed for this study. Participants also completed questionnaires on demographics, sexual preferences, sexual risk evaluations, the Sexual Sensation Seeking Scale (SSS), and the Sexual Inhibition Subscale 2 (SIS2) of the Sexual Inhibition/Sexual Excitation Scales-Short Form (SIS/SES - SF). The overall confidence of participants to evaluate sexual risks reduced after playing the game (Psimulations as a serious game for sex education. Engaging in the Term on the Tides game had an impact on participants' confidence in evaluating sexual risks. ©Anastasia Eleftheriou, Seth Bullock, Cynthia A Graham, Roger Ingham. Originally published in JMIR Serious Games (http://games.jmir.org), 03.05.2017.

Rigid body motion in stereo 3D simulation

International Nuclear Information System (INIS)

Zabunov, Svetoslav

2010-01-01

This paper addresses the difficulties experienced by first-grade students studying rigid body motion at Sofia University. Most quantities describing the rigid body are in relations that the students find hard to visualize and understand. They also lose the notion of cause-result relations between vector quantities, such as the relation between torque and angular momentum. Consequently, the understanding of physical laws and conservation principles in free rigid body motion is hampered. This paper presents the capabilities of a 3D simulation, which aims to clarify these questions to the students, who are taught mechanics in the general physics course. The rigid body motion simulations may be observed at http://ialms.net/sim/, and are intended to complement traditional learning practices, not replace them, as the author shares the opinion that no simulation may fully resemble reality.

Quantum mechanical simulation methods for studying biological systems

International Nuclear Information System (INIS)

Bicout, D.; Field, M.

1996-01-01

Most known biological mechanisms can be explained using fundamental laws of physics and chemistry and a full understanding of biological processes requires a multidisciplinary approach in which all the tools of biology, chemistry and physics are employed. An area of research becoming increasingly important is the theoretical study of biological macromolecules where numerical experimentation plays a double role of establishing a link between theoretical models and predictions and allowing a quantitative comparison between experiments and models. This workshop brought researchers working on different aspects of the development and application of quantum mechanical simulation together, assessed the state-of-the-art in the field and highlighted directions for future research. Fourteen lectures (theoretical courses and specialized seminars) deal with following themes: 1) quantum mechanical calculations of large systems, 2) ab initio molecular dynamics where the calculation of the wavefunction and hence the energy and forces on the atoms for a system at a single nuclear configuration are combined with classical molecular dynamics algorithms in order to perform simulations which use a quantum mechanical potential energy surface, 3) quantum dynamical simulations, electron and proton transfer processes in proteins and in solutions and finally, 4) free seminars that helped to enlarge the scope of the workshop. (N.T.)

Simulations of groundwater flow, transport, and age in Albuquerque, New Mexico, for a study of transport of anthropogenic and natural contaminants (TANC) to public-supply wells

Science.gov (United States)

Heywood, Charles E.

2013-01-01

flow and transport through these wells requires time discretization that adequately represents periods of pumping and non-pumping. The effects of intra-borehole flow are not fully represented in the simulation because it employs seasonal stress periods, which are longer than periods of pumping and non-pumping. Further simulations utilizing daily pumpage data and model stress periods may help quantify the relative effects of intra-borehole versus advective aquifer flow on the transport of contaminants near the public-supply wells. The fraction of young water withdrawn from the studied supply well varies with simulated pumping rates due to changes in the relative contributions to flow from different aquifer intervals. The advective transport of dissolved solutes from a known contaminant source to the public-supply wells was simulated by using particle-tracking. Because of the transient groundwater flow field, scenarios with alternative contaminant release times result in different simulated-particle fates, most of which are withdrawn from the aquifer at wells that are between the source and the studied supply well. The relatively small effective porosity required to simulate advective transport from the simulated contaminant source to the studied supply well is representative of a preferential pathway and not the predominant aquifer effective porosity that was estimated by the calibration of the model to observed chemical-tracer concentrations.

White book Escrime. Climatic simulation studies

International Nuclear Information System (INIS)

Terray, L.; Braconnot, P.

2007-01-01

The ESCRIME project aims to manage the analysis realized on the climatic simulations on the framework of the fourth report of the GIEC (group of intergovernmental experts on the climate evolution), in particularly the simulations based on french models. This white book is constituted by 8 chapters: the global scenario, the climatic sensibility, the variation modes, the regionalization and the extremes, the hydrological cycle, the polar regions and the cryo-sphere, the carbon cycle, detection and attributions. (A.L.B.)

Monte Carlo simulation study of the muon-induced neutron flux at LNGS

International Nuclear Information System (INIS)

Persiani, R.; Garbini, M.; Massoli, F.; Sartorelli, G; Selvi, M.

2011-01-01

Muon-induced neutrons are ultimate background for all the experiments searching for rare events in underground laboratories. Several measurements and simulations were performed concerning the neutron production and propagation but there are disagreements between experimental data and simulations. In this work we present our Monte-Carlo simulation study, based on Geant4, to estimate the muon-induced neutron flux at LNGS. The obtained integral flux of neutrons above 1 MeV is 2.31 x 10 -10 n/cm 2 /s.

Simulative study on dose distribution of 103Pd stent in blood-vessel

International Nuclear Information System (INIS)

Yuan Shuyu; Dai Guangfu; Xu Zhiyong; Sun Fuyin; Xu Shuhe; Ma Fengwu

2003-01-01

Objective: To evaluate the dose distribution of 103 Pd stent in the blood-vessel. Methods: Simulative study on dose distribution of endovascular 103 Pd stent was conducted with thermoluminescence dosimeter. The vessel wall was substituted by muscle equivalent material in this simulative study. Results: When radioactivity of the study 103 Pd stent was 9.8 MBq the absorbed dose from the stent surface by muscle equivalent material was 9.8 Gy at 17 d (the half-life period of 103 Pd). The radioactivity of 103 Pd stent surface rapidly attenuated over the radial distance. 80% of the radioactivity at the area that was radially 0.4 mm apart from the stent surface was absorbed by the simulative blood-vessel wall. Conclusion: Endovascular 103 Pd stent does not exert significant injury on the surrounding organs or tissues

A simulation study to quantify the impacts of exposure measurement error on air pollution health risk estimates in copollutant time-series models.

Science.gov (United States)

BackgroundExposure measurement error in copollutant epidemiologic models has the potential to introduce bias in relative risk (RR) estimates. A simulation study was conducted using empirical data to quantify the impact of correlated measurement errors in time-series analyses of a...

Evaluation of the UK Met Office's HadGEM3-RA and HadRM3P regional climate models within South America-CORDEX simulations: ENSO related interannual precipitation variability

Science.gov (United States)

Bozkurt, D.; Rojas, M.

2014-12-01

This study aims to investigate and compare the ability of the UK Met Office's HadGEM3-RA and HadRM3P regional climate models (RCMs) to simulate mean and interannual variability of precipitation over South America with a special focus on Chile. The HadGEM3-RA is a regional version of the newly developed HadGEM3 global model and the HadRM3P is based on the earlier HadCM3 global model. The RCMs simulations were carried out at 0.44o x 0.44o degree resolution over South America-CORDEX domain for the period 1989-2008. The initial and boundary conditions were provided by ERA-Interim Reanalysis data available at 6-h intervals with a resolution of 1.5o x 1.5o in the horizontal and 37 pressure levels. We compare the results against a number of observational datasets, including gridded dataset of CRU, UDEL, TRMM and GPCP. Moreover, available station data is derived from Direccion General de Aguas (DGA) mainly for Central Chile, which is the heartland of Chile with the highest population and important economic activities. The analysis is mainly focused on evaluating the abilities of the RCMs in simulating spatial pattern and ENSO related precipitation variability in different subregions of South America-CORDEX domain. In general, both RCMs have a good skill in reproducing spatial pattern and annual cycle of observed precipitation in climatically different subregions. However, both RCMs tend to underestimate precipitation in the Amazon Basin, which is more pronounced in the HadRM3P simulations. On the contrary, the RCMs tend to overestimate the precipitation over the Andes and southern Chile. The overestimation could be related to the physical core of the RCMs, but the discrepancies could also arise due to insufficient station network, especially in the mountainous areas, potentially yielding smaller precipitation quantities in the observed data than the true ones. In terms of interannual variability, the models capture ENSO related wet and dry interannual precipitation

Study of TXRF experimental system by Monte Carlo simulation

International Nuclear Information System (INIS)

Costa, Ana Cristina M.; Leitao, Roberta G.; Lopes, Ricardo T.; Anjos, Marcelino J.; Conti, Claudio C.

2011-01-01

The Total-Reflection X-ray Fluorescence (TXRF) technique offers unique possibilities to study the concentrations of a wide range of trace elements in various types of samples. Besides that, the TXRF technique is widely used to study the trace elements in biological, medical and environmental samples due to its multielemental character as well as simplicity of sample preparation and quantification methods used. In general the TXRF experimental setup is not simple and might require substantial experimental efforts. On the other hand, in recent years, experimental TXRF portable systems have been developed. It has motivated us to develop our own TXRF portable system. In this work we presented a first step in order to optimize a TXRF experimental setup using Monte Carlo simulation by MCNP code. The results found show that the Monte Carlo simulation method can be used to investigate the development of a TXRF experimental system before its assembly. (author)

Introduction to Network Simulator NS2

CERN Document Server

Issariyakul, Teerawat

2012-01-01

"Introduction to Network Simulator NS2" is a primer providing materials for NS2 beginners, whether students, professors, or researchers for understanding the architecture of Network Simulator 2 (NS2) and for incorporating simulation modules into NS2. The authors discuss the simulation architecture and the key components of NS2 including simulation-related objects, network objects, packet-related objects, and helper objects. The NS2 modules included within are nodes, links, SimpleLink objects, packets, agents, and applications. Further, the book covers three helper modules: timers, ra

A study of the use of simulated work task situations in interactive information retrieval evaluations

DEFF Research Database (Denmark)

Borlund, Pia

2016-01-01

Purpose – The purpose of this paper is to report a study of how the test instrument of a simulated work task situation is used in empirical evaluations of interactive information retrieval (IIR) and reported in the research literature. In particular, the author is interested to learn whether....... The paper addresses the need to carefully design and tailor simulated work task situations to suit the test participants in order to obtain the intended authentic and realistic IIR under study. Keywords Interactive information retrieval study, IIR study, Test design, Simulated work task situations, Meta-evaluation...... situations in IIR evaluations. In particular, with respect to the design and creation of realistic simulated work task situations. There is a lack of tailoring of the simulated work task situations to the test participants. Likewise, the requirement to include the test participants’ personal information...

Do technical skills correlate with non-technical skills in crisis resource management: a simulation study.

Science.gov (United States)

Riem, N; Boet, S; Bould, M D; Tavares, W; Naik, V N

2012-11-01

Both technical skills (TS) and non-technical skills (NTS) are key to ensuring patient safety in acute care practice and effective crisis management. These skills are often taught and assessed separately. We hypothesized that TS and NTS are not independent of each other, and we aimed to evaluate the relationship between TS and NTS during a simulated intraoperative crisis scenario. This study was a retrospective analysis of performances from a previously published work. After institutional ethics approval, 50 anaesthesiology residents managed a simulated crisis scenario of an intraoperative cardiac arrest secondary to a malignant arrhythmia. We used a modified Delphi approach to design a TS checklist, specific for the management of a malignant arrhythmia requiring defibrillation. All scenarios were recorded. Each performance was analysed by four independent experts. For each performance, two experts independently rated the technical performance using the TS checklist, and two other experts independently rated NTS using the Anaesthetists' Non-Technical Skills score. TS and NTS were significantly correlated to each other (r=0.45, P<0.05). During a simulated 5 min resuscitation requiring crisis resource management, our results indicate that TS and NTS are related to one another. This research provides the basis for future studies evaluating the nature of this relationship, the influence of NTS training on the performance of TS, and to determine whether NTS are generic and transferrable between crises that require different TS.

Exploring Students' Flow Experiences in Business Simulation Games

Science.gov (United States)

Buil, I.; Catalán, S.; Martínez, E.

2018-01-01

Business simulation games are a motivational and engaging tool for teaching business management. However, relatively little is known about what factors contribute to their success. This study explores the role of flow experienced while using business simulation games. Specifically, this research investigates the influence of challenge, skills,…

Repetition-related reductions in neural activity reveal component processes of mental simulation.

Science.gov (United States)

Szpunar, Karl K; St Jacques, Peggy L; Robbins, Clifford A; Wig, Gagan S; Schacter, Daniel L

2014-05-01

In everyday life, people adaptively prepare for the future by simulating dynamic events about impending interactions with people, objects and locations. Previous research has consistently demonstrated that a distributed network of frontal-parietal-temporal brain regions supports this ubiquitous mental activity. Nonetheless, little is known about the manner in which specific regions of this network contribute to component features of future simulation. In two experiments, we used a functional magnetic resonance (fMR)-repetition suppression paradigm to demonstrate that distinct frontal-parietal-temporal regions are sensitive to processing the scenarios or what participants imagined was happening in an event (e.g., medial prefrontal, posterior cingulate, temporal-parietal and middle temporal cortices are sensitive to the scenarios associated with future social events), people (medial prefrontal cortex), objects (inferior frontal and premotor cortices) and locations (posterior cingulate/retrosplenial, parahippocampal and posterior parietal cortices) that typically constitute simulations of personal future events. This pattern of results demonstrates that the neural substrates of these component features of event simulations can be reliably identified in the context of a task that requires participants to simulate complex, everyday future experiences.

Scoping study of flowpath of simulated fission products during secondary burning of crushed HTGR fuel in a quartz fluidized-bed burner

International Nuclear Information System (INIS)

Rindfleisch, J.A.; Barnes, V.H.

1976-04-01

The results of four experimental runs in which isotopic tracers were used to simulate fission products during fluidized bed secondary burning of HTGR fuel were studied. The experimental tests provided insight relative to the flow path of fission products during fluidized-bed burning of HTGR fuel

Simulations to study the static polarization limit for RHIC lattice

Science.gov (United States)

Duan, Zhe; Qin, Qing

2016-01-01

A study of spin dynamics based on simulations with the Polymorphic Tracking Code (PTC) is reported, exploring the dependence of the static polarization limit on various beam parameters and lattice settings for a practical RHIC lattice. It is shown that the behavior of the static polarization limit is dominantly affected by the vertical motion, while the effect of beam-beam interaction is small. In addition, the “nonresonant beam polarization” observed and studied in the lattice-independent model is also observed in this lattice-dependent model. Therefore, this simulation study gives insights of polarization evolution at fixed beam energies, that are not available in simple spin tracking. Supported by the U.S. Department of Energy (DE-AC02-98CH10886), Hundred-Talent Program (Chinese Academy of Sciences), and National Natural Science Foundation of China (11105164)

Focus on Games & Simulations: Trends+Technologies+Case Studies

Science.gov (United States)

Weinstein, Margery

2011-01-01

A changing mindset combined with changing technology is driving the use of games and simulations. People are becoming more open to using games and simulations for learning, and, at the same time, the technologies are making the development of games and simulations easier and faster than a mere five years ago. Together, the changing mindset and the…

Integration of a driving simulator and a traffic simulator case study: Exploring drivers' behavior in response to variable message signs

Directory of Open Access Journals (Sweden)

Mansoureh Jeihani

2017-12-01

Full Text Available For the first time, a driving simulator has been integrated with a traffic simulator at the network level to allow subjects to drive in a fairly realistic environment with a realistic traffic flow and density. A 10 mi2 (25 km2 network was developed in a driving simulator and then exported to a traffic simulator. About 30 subjects drove the simulator under different traffic and driving conditions and variable message sign (VMS information, both with and without integration. Route guidance was available for the subjects. The challenges of the integration process are explained and its advantages investigated. The study concluded that traffic density, VMS reliability and compliance behavior are higher when driving and traffic simulators are integrated. To find factors affecting route diversion, researchers applied a binary logistic regression model. The results indicated that the original chosen route, displayed VMS information, subjects' attitude toward VMS information helpfulness, and their level of exposure to VMS affect route diversion. In addition, a multinomial logistic regression model was employed to investigate important factors in route choice. The results revealed that there is a significant correlation with driver route choice behavior and their actual travel time, the need for GPS, VMS exposure and also the designed scenarios. It should be noted that the paper was peer-reviewed by TRB and presented at the TRB Annual Meeting, Washington, D.C., January 2016. Keywords: Integration, Variable message sign, Compliance behavior, Driving simulator, Traffic simulator, Discrete choice analysis

A generic analytical foot rollover model for predicting translational ankle kinematics in gait simulation studies.

Science.gov (United States)

Ren, Lei; Howard, David; Ren, Luquan; Nester, Chris; Tian, Limei

2010-01-19

The objective of this paper is to develop an analytical framework to representing the ankle-foot kinematics by modelling the foot as a rollover rocker, which cannot only be used as a generic tool for general gait simulation but also allows for case-specific modelling if required. Previously, the rollover models used in gait simulation have often been based on specific functions that have usually been of a simple form. In contrast, the analytical model described here is in a general form that the effective foot rollover shape can be represented by any polar function rho=rho(phi). Furthermore, a normalized generic foot rollover model has been established based on a normative foot rollover shape dataset of 12 normal healthy subjects. To evaluate model accuracy, the predicted ankle motions and the centre of pressure (CoP) were compared with measurement data for both subject-specific and general cases. The results demonstrated that the ankle joint motions in both vertical and horizontal directions (relative RMSE approximately 10%) and CoP (relative RMSE approximately 15% for most of the subjects) are accurately predicted over most of the stance phase (from 10% to 90% of stance). However, we found that the foot cannot be very accurately represented by a rollover model just after heel strike (HS) and just before toe off (TO), probably due to shear deformation of foot plantar tissues (ankle motion can occur without any foot rotation). The proposed foot rollover model can be used in both inverse and forward dynamics gait simulation studies and may also find applications in rehabilitation engineering. Copyright 2009 Elsevier Ltd. All rights reserved.

Simulating a base population in honey bee for molecular genetic studies

Directory of Open Access Journals (Sweden)

Gupta Pooja

2012-06-01

Full Text Available Abstract Background Over the past years, reports have indicated that honey bee populations are declining and that infestation by an ecto-parasitic mite (Varroa destructor is one of the main causes. Selective breeding of resistant bees can help to prevent losses due to the parasite, but it requires that a robust breeding program and genetic evaluation are implemented. Genomic selection has emerged as an important tool in animal breeding programs and simulation studies have shown that it yields more accurate breeding value estimates, higher genetic gain and low rates of inbreeding. Since genomic selection relies on marker data, simulations conducted on a genomic dataset are a pre-requisite before selection can be implemented. Although genomic datasets have been simulated in other species undergoing genetic evaluation, simulation of a genomic dataset specific to the honey bee is required since this species has a distinct genetic and reproductive biology. Our software program was aimed at constructing a base population by simulating a random mating honey bee population. A forward-time population simulation approach was applied since it allows modeling of genetic characteristics and reproductive behavior specific to the honey bee. Results Our software program yielded a genomic dataset for a base population in linkage disequilibrium. In addition, information was obtained on (1 the position of markers on each chromosome, (2 allele frequency, (3 χ2 statistics for Hardy-Weinberg equilibrium, (4 a sorted list of markers with a minor allele frequency less than or equal to the input value, (5 average r2 values of linkage disequilibrium between all simulated marker loci pair for all generations and (6 average r2 value of linkage disequilibrium in the last generation for selected markers with the highest minor allele frequency. Conclusion We developed a software program that takes into account the genetic and reproductive biology specific to the honey bee

A simulation based engineering method to support HAZOP studies

DEFF Research Database (Denmark)

Enemark-Rasmussen, Rasmus; Cameron, David; Angelo, Per Bagge

2012-01-01

the conventional HAZOP procedure. The method systematically generates failure scenarios by considering process equipment deviations with pre-defined failure modes. The effect of failure scenarios is then evaluated using dynamic simulations -in this study the K-Spice® software used. The consequences of each failure...

Simulating solar MHD

Directory of Open Access Journals (Sweden)

M. Schüssler

Full Text Available Two aspects of solar MHD are discussed in relation to the work of the MHD simulation group at KIS. Photospheric magneto-convection, the nonlinear interaction of magnetic field and convection in a strongly stratified, radiating fluid, is a key process of general astrophysical relevance. Comprehensive numerical simulations including radiative transfer have significantly improved our understanding of the processes and have become an important tool for the interpretation of observational data. Examples of field intensification in the solar photosphere ('convective collapse' are shown. The second line of research is concerned with the dynamics of flux tubes in the convection zone, which has far-reaching implications for our understanding of the solar dynamo. Simulations indicate that the field strength in the region where the flux is stored before erupting to form sunspot groups is of the order of 10⁵ G, an order of magnitude larger than previous estimates based on equipartition with the kinetic energy of convective flows.

Key words. Solar physics · astrophysics and astronomy (photosphere and chromosphere; stellar interiors and dynamo theory; numerical simulation studies.

Analysis of nanowire transistor based nitrogen dioxide gas sensor – A simulation study

Directory of Open Access Journals (Sweden)

Gaurav Saxena

2015-06-01

Full Text Available Sensors sensitivity, selectivity and stability has always been a prime design concern for gas sensors designers. Modeling and simulation of gas sensors aids the designers in improving their performance. In this paper, different routes for the modeling and simulation of a semiconducting gas sensor is presented. Subsequently, by employing one of the route, the response of Zinc Oxide nanowire transistor towards nitrogen dioxide ambient is simulated. In addition to the sensing mechanism, simulation study of gas species desorption by applying a recovery voltage is also presented.

An application of sedimentation simulation in Tahe oilfield

Science.gov (United States)

Tingting, He; Lei, Zhao; Xin, Tan; Dongxu, He

2017-12-01

The braided river delta develops in Triassic low oil formation in the block 9 of Tahe oilfield, but its sedimentation evolution process is unclear. By using sedimentation simulation technology, sedimentation process and distribution of braided river delta are studied based on the geological parameters including sequence stratigraphic division, initial sedimentation environment, relative lake level change and accommodation change, source supply and sedimentary transport pattern. The simulation result shows that the error rate between strata thickness of simulation and actual strata thickness is small, and the single well analysis result of simulation is highly consistent with the actual analysis, which can prove that the model is reliable. The study area belongs to braided river delta retrogradation evolution process, which provides favorable basis for fine reservoir description and prediction.

A Virtual Mixture Approach to the Study of Multistate Equilibrium: Application to Constant pH Simulation in Explicit Water

Science.gov (United States)

Wu, Xiongwu; Brooks, Bernard R.

2015-01-01

Chemical and thermodynamic equilibrium of multiple states is a fundamental phenomenon in biology systems and has been the focus of many experimental and computational studies. This work presents a simulation method to directly study the equilibrium of multiple states. This method constructs a virtual mixture of multiple states (VMMS) to sample the conformational space of all chemical states simultaneously. The VMMS system consists of multiple subsystems, one for each state. The subsystem contains a solute and a solvent environment. The solute molecules in all subsystems share the same conformation but have their own solvent environments. Transition between states is implicated by the change of their molar fractions. Simulation of a VMMS system allows efficient calculation of relative free energies of all states, which in turn determine their equilibrium molar fractions. For systems with a large number of state transition sites, an implicit site approximation is introduced to minimize the cost of simulation. A direct application of the VMMS method is for constant pH simulation to study protonation equilibrium. Applying the VMMS method to a heptapeptide of 3 ionizable residues, we calculated the pKas of those residues both with all explicit states and with implicit sites and obtained consistent results. For mouse epidermal growth factor of 9 ionizable groups, our VMMS simulations with implicit sites produced pKas of all 9 ionizable groups and the results agree qualitatively with NMR measurement. This example demonstrates the VMMS method can be applied to systems of a large number of ionizable groups and the computational cost scales linearly with the number of ionizable groups. For one of the most challenging systems in constant pH calculation, SNase Δ+PHS/V66K, our VMMS simulation shows that it is the state-dependent water penetration that causes the large deviation in lysine66’s pKa. PMID:26506245

A Virtual Mixture Approach to the Study of Multistate Equilibrium: Application to Constant pH Simulation in Explicit Water.

Directory of Open Access Journals (Sweden)

Xiongwu Wu

2015-10-01

Full Text Available Chemical and thermodynamic equilibrium of multiple states is a fundamental phenomenon in biology systems and has been the focus of many experimental and computational studies. This work presents a simulation method to directly study the equilibrium of multiple states. This method constructs a virtual mixture of multiple states (VMMS to sample the conformational space of all chemical states simultaneously. The VMMS system consists of multiple subsystems, one for each state. The subsystem contains a solute and a solvent environment. The solute molecules in all subsystems share the same conformation but have their own solvent environments. Transition between states is implicated by the change of their molar fractions. Simulation of a VMMS system allows efficient calculation of relative free energies of all states, which in turn determine their equilibrium molar fractions. For systems with a large number of state transition sites, an implicit site approximation is introduced to minimize the cost of simulation. A direct application of the VMMS method is for constant pH simulation to study protonation equilibrium. Applying the VMMS method to a heptapeptide of 3 ionizable residues, we calculated the pKas of those residues both with all explicit states and with implicit sites and obtained consistent results. For mouse epidermal growth factor of 9 ionizable groups, our VMMS simulations with implicit sites produced pKas of all 9 ionizable groups and the results agree qualitatively with NMR measurement. This example demonstrates the VMMS method can be applied to systems of a large number of ionizable groups and the computational cost scales linearly with the number of ionizable groups. For one of the most challenging systems in constant pH calculation, SNase Δ+PHS/V66K, our VMMS simulation shows that it is the state-dependent water penetration that causes the large deviation in lysine66's pKa.

A Virtual Mixture Approach to the Study of Multistate Equilibrium: Application to Constant pH Simulation in Explicit Water.

Science.gov (United States)

Wu, Xiongwu; Brooks, Bernard R

2015-10-01

Chemical and thermodynamic equilibrium of multiple states is a fundamental phenomenon in biology systems and has been the focus of many experimental and computational studies. This work presents a simulation method to directly study the equilibrium of multiple states. This method constructs a virtual mixture of multiple states (VMMS) to sample the conformational space of all chemical states simultaneously. The VMMS system consists of multiple subsystems, one for each state. The subsystem contains a solute and a solvent environment. The solute molecules in all subsystems share the same conformation but have their own solvent environments. Transition between states is implicated by the change of their molar fractions. Simulation of a VMMS system allows efficient calculation of relative free energies of all states, which in turn determine their equilibrium molar fractions. For systems with a large number of state transition sites, an implicit site approximation is introduced to minimize the cost of simulation. A direct application of the VMMS method is for constant pH simulation to study protonation equilibrium. Applying the VMMS method to a heptapeptide of 3 ionizable residues, we calculated the pKas of those residues both with all explicit states and with implicit sites and obtained consistent results. For mouse epidermal growth factor of 9 ionizable groups, our VMMS simulations with implicit sites produced pKas of all 9 ionizable groups and the results agree qualitatively with NMR measurement. This example demonstrates the VMMS method can be applied to systems of a large number of ionizable groups and the computational cost scales linearly with the number of ionizable groups. For one of the most challenging systems in constant pH calculation, SNase Δ+PHS/V66K, our VMMS simulation shows that it is the state-dependent water penetration that causes the large deviation in lysine66's pKa.

3D simulation studies of tokamak plasmas using MHD and extended-MHD models

International Nuclear Information System (INIS)

Park, W.; Chang, Z.; Fredrickson, E.; Fu, G.Y.

1996-01-01

The M3D (Multi-level 3D) tokamak simulation project aims at the simulation of tokamak plasmas using a multi-level tokamak code package. Several current applications using MHD and Extended-MHD models are presented; high-β disruption studies in reversed shear plasmas using the MHD level MH3D code, ω *i stabilization and nonlinear island saturation of TAE mode using the hybrid particle/MHD level MH3D-K code, and unstructured mesh MH3D ++ code studies. In particular, three internal mode disruption mechanisms are identified from simulation results which agree which agree well with experimental data

Study on Photon Transport Problem Based on the Platform of Molecular Optical Simulation Environment

Directory of Open Access Journals (Sweden)

Kuan Peng

2010-01-01

Full Text Available As an important molecular imaging modality, optical imaging has attracted increasing attention in the recent years. Since the physical experiment is usually complicated and expensive, research methods based on simulation platforms have obtained extensive attention. We developed a simulation platform named Molecular Optical Simulation Environment (MOSE to simulate photon transport in both biological tissues and free space for optical imaging based on noncontact measurement. In this platform, Monte Carlo (MC method and the hybrid radiosity-radiance theorem are used to simulate photon transport in biological tissues and free space, respectively, so both contact and noncontact measurement modes of optical imaging can be simulated properly. In addition, a parallelization strategy for MC method is employed to improve the computational efficiency. In this paper, we study the photon transport problems in both biological tissues and free space using MOSE. The results are compared with Tracepro, simplified spherical harmonics method (SPn, and physical measurement to verify the performance of our study method on both accuracy and efficiency.

Study on photon transport problem based on the platform of molecular optical simulation environment.

Science.gov (United States)

Peng, Kuan; Gao, Xinbo; Liang, Jimin; Qu, Xiaochao; Ren, Nunu; Chen, Xueli; Ma, Bin; Tian, Jie

2010-01-01

As an important molecular imaging modality, optical imaging has attracted increasing attention in the recent years. Since the physical experiment is usually complicated and expensive, research methods based on simulation platforms have obtained extensive attention. We developed a simulation platform named Molecular Optical Simulation Environment (MOSE) to simulate photon transport in both biological tissues and free space for optical imaging based on noncontact measurement. In this platform, Monte Carlo (MC) method and the hybrid radiosity-radiance theorem are used to simulate photon transport in biological tissues and free space, respectively, so both contact and noncontact measurement modes of optical imaging can be simulated properly. In addition, a parallelization strategy for MC method is employed to improve the computational efficiency. In this paper, we study the photon transport problems in both biological tissues and free space using MOSE. The results are compared with Tracepro, simplified spherical harmonics method (SP(n)), and physical measurement to verify the performance of our study method on both accuracy and efficiency.

Inquiry-Based Whole-Class Teaching with Computer Simulations in Physics

NARCIS (Netherlands)

Rutten, N.P.G.; van der Veen, Jan T.; van Joolingen, Wouter

2015-01-01

In this study we investigated the pedagogical context of whole-class teaching with computer simulations. We examined relations between the attitudes and learning goals of teachers and their students regarding the use of simulations in whole-class teaching, and how teachers implement these

Musculoskeletal Disorders in Ophthalmologists After Simulated Cataract Operation: A Pilot Study.

Science.gov (United States)

Pearce, Zachary D; Zatkin, Mathew A; Bruner, Jon

2017-12-01

Musculoskeletal disorders are a common problem among ophthalmologists, likely due to ergonomic challenges. Most research on the topic has been survey-based studies, which carry inherent weaknesses. To examine the frequency and pattern of musculoskeletal dysfunction induced by performing a surgical procedure and to quantify the improvement after ergonomic interventions. Ophthalmology residents from a single academic institution were invited to participate in the study on a volunteer basis. Preexisting musculoskeletal disorders; previous spinal, cervical, or shoulder surgery; or limited range of motion of the upper body or arms were exclusion criteria. The interventions consisted of a surgical simulation session and a control session, each lasting 2 hours. For the surgical simulation session, a musculoskeletal examination was performed at the beginning and end of the 2-hour session after the participants used the Eyesi Cataract Surgery Simulator (VRmagic). A musculoskeletal examination was performed by the palpatory screener (M.A.Z.) at the beginning and conclusion of the 2-hour control session, which consisted of both passive and active tasks. The musculoskeletal screener was blinded as to which session the participant was completing at the time of the examinations, as well as any musculoskeletal examination findings from before the intervention. All participants completed both sessions, but they were randomized into which session they were to complete first. Participants completed each session one after the other. Eight participants completed both sessions, and 32 musculoskeletal examinations were performed. In the surgical simulation session, after using the simulator, 5 of 8 participants had an increase in the number of spinal levels with tissue texture abnormalities, and 3 had no change. Of those in the control session, 5 participants had a decrease in the number of spinal levels with tissue texture abnormalities after a period of rest. Three participants in the

Simulation in Sport Finance

Science.gov (United States)

Drayer, Joris; Rascher, Dan

2010-01-01

Simulations have long been used in business schools to give students experience making real-world decisions in a relatively low risk environment. The OAKLAND A'S BASEBALL BUSINESS SIMULATOR takes a traditional business simulation and applies it to the sport industry, in which sales of tangible products are replaced by sales of experiences provided…

A Web-based Simulator for Sample Size and Power Estimation in Animal Carcinogenicity Studies

Directory of Open Access Journals (Sweden)

Hojin Moon

2002-12-01

Full Text Available A Web-based statistical tool for sample size and power estimation in animal carcinogenicity studies is presented in this paper. It can be used to provide a design with sufficient power for detecting a dose-related trend in the occurrence of a tumor of interest when competing risks are present. The tumors of interest typically are occult tumors for which the time to tumor onset is not directly observable. It is applicable to rodent tumorigenicity assays that have either a single terminal sacrifice or multiple (interval sacrifices. The design is achieved by varying sample size per group, number of sacrifices, number of sacrificed animals at each interval, if any, and scheduled time points for sacrifice. Monte Carlo simulation is carried out in this tool to simulate experiments of rodent bioassays because no closed-form solution is available. It takes design parameters for sample size and power estimation as inputs through the World Wide Web. The core program is written in C and executed in the background. It communicates with the Web front end via a Component Object Model interface passing an Extensible Markup Language string. The proposed statistical tool is illustrated with an animal study in lung cancer prevention research.

Standardised simulation-based emergency and intensive care nursing curriculum to improve nursing students' performance during simulated resuscitation: A quasi-experimental study.

Science.gov (United States)

Chen, Jie; Yang, Jian; Hu, Fen; Yu, Si-Hong; Yang, Bing-Xiang; Liu, Qian; Zhu, Xiao-Ping

2018-03-14

Simulation-based curriculum has been demonstrated as crucial to nursing education in the development of students' critical thinking and complex clinical skills during a resuscitation simulation. Few studies have comprehensively examined the effectiveness of a standardised simulation-based emergency and intensive care nursing curriculum on the performance of students in a resuscitation simulation. To evaluate the impact of a standardised simulation-based emergency and intensive care nursing curriculum on nursing students' response time in a resuscitation simulation. Two-group, non-randomised quasi-experimental design. A simulation centre in a Chinese University School of Nursing. Third-year nursing students (N = 39) in the Emergency and Intensive Care course were divided into a control group (CG, n = 20) and an experimental group (EG, n = 19). The experimental group participated in a standardised high-technology, simulation-based emergency and intensive care nursing curriculum. The standardised simulation-based curriculum for third-year nursing students consists of three modules: disaster response, emergency care, and intensive care, which include clinical priorities (e.g. triage), basic resuscitation skills, airway/breathing management, circulation management and team work with eighteen lecture hours, six skill-practice hours and twelve simulation hours. The control group took part in the traditional curriculum. This course included the same three modules with thirty-four lecture hours and two skill-practice hours (trauma). Perceived benefits included decreased median (interquartile ranges, IQR) seconds to start compressions [CG 32 (25-75) vs. EG 20 (18-38); p  0.05] and defibrillation [CG 222 (194-254) vs. EG 221 (214-248); p > 0.05] at the beginning of the course. A simulation-based emergency and intensive care nursing curriculum was created and well received by third-year nursing students and associated with decreased response time in a

Simulating Study on Drive System Performance for Hybrid Electric Bus Based on ADVISOR

Directory of Open Access Journals (Sweden)

Wang Xingxing

2017-01-01

Full Text Available Hybrid electric bus has a number of advantages when compared with ordinary passenger cars, but in the dynamic matching and the vehicle performance are difficult to detect, thus limits its development process. In this paper, combined with the actual models, the hybrid electric bus module parameters were modified in the software of ADVISOR (Advanced Vehicle Simulator, main including: module of the vehicle, the wheel module, motor module, a battery module and engine module, three kinds of bus models for A, B and C were established, and the related performance that need to be analyzed was set up, such as acceleration, gradability, emissions and energy utilization and so on, in order to ensure the vehicle running in the same environment and convenient for comparison, a fixed vehicle driving cycles was chose, then the simulation results was analyzed, and the various performance was compared with the dynamic indicators and economic indicators which determined by referencing of traditional city bus standard and each other, and finally, the performance optimal model of B was chose out which can meet the demand, its related performance parameters of the simulation results are as follows: the best gradability is 26%, maximum speed is 72.7km/h, maximum acceleration is 1.7m/s2, 0~50km/h acceleration time is 9.5s and fuel consumption is 25L/km.

Modeling and real time simulation of an HVDC inverter feeding a weak AC system based on commutation failure study.

Science.gov (United States)

Mankour, Mohamed; Khiat, Mounir; Ghomri, Leila; Chaker, Abdelkader; Bessalah, Mourad

2018-06-01

This paper presents modeling and study of 12-pulse HVDC (High Voltage Direct Current) based on real time simulation where the HVDC inverter is connected to a weak AC system. In goal to study the dynamic performance of the HVDC link, two serious kind of disturbance are applied at HVDC converters where the first one is the single phase to ground AC fault and the second one is the DC link to ground fault. The study is based on two different mode of analysis, which the first is to test the performance of the DC control and the second is focalized to study the effect of the protection function on the system behavior. This real time simulation considers the strength of the AC system to witch is connected and his relativity with the capacity of the DC link. The results obtained are validated by means of RT-lab platform using digital Real time simulator Hypersim (OP-5600), the results carried out show the effect of the DC control and the influence of the protection function to reduce the probability of commutation failures and also for helping inverter to take out from commutation failure even while the DC control fails to eliminate them. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.