WorldWideScience

Sample records for related petroleum-field brines

  1. Transport of Pb and Zn by carboxylate complexes in basinal ore fluids and related petroleum-field brines at 100°C: the influence of pH and oxygen fugacity

    Directory of Open Access Journals (Sweden)

    Giordano Thomas H

    2002-09-01

    can mobilize up to 3% of the total Pb and up to 1.3% of the total Zn as carboxylate complexes. Furthermore, these percentages, under the most favorable conditions, correspond to approximately 1 to 100 ppm of these metals in solution; concentrations that are adequate to form economic deposits of these metals. However, the field evidence suggests that all of these optimum conditions for carboxylate complexation are rarely met at the same time. A comparison of the composite ore fluid compositions from this study and modern brine data shows that the ore brines, corresponding to log –pH conditions based on the Anderson (1975 and Giordano (1994 model fluids, are similar in many respects to modern, high trace-metal petroleum-field brines. The principal differences between modern high trace-metal brines and the composite ore fluids of Anderson (1975 and Giordano (1994 relate to their carboxylate anion content. The reported concentrations of monocarboxylate anions (∑monocbx and dicarboxylate anions (Edicbx in high trace-metal petroleum-field brines (-1 and -1, respectively are significantly lower than the concentrations assumed in the modelled brines of this study (∑monocbx = 7 700 mg L-1 and ∑dicbx = 300 mg L-1. There are also major differences in the corresponding total chloride to carboxylate ratio (∑mCl/∑mcbx and monocarboxylate to dicarboxylate ratio (∑mmonocbx/∑mdicbx. Modern high trace-metal brines have much higher ∑mCl/∑mcbx values and, therefore, the contribution of carboxylate complexes to the total Pb and Zn content in these modern brines is likely to be significantly less than the 1 to 3 percent for the composite ore fluids of Anderson (1975 and Giordano (1994. The composite ore-brine based on the Giordano and Barnes (1981 MVT ore fluid is comparable to the high salinity (> 170 000 mg L-1 TDS subset of modern brines characterized by low trace-metal content and high total reduced sulfur (∑H2S. A comparison of the Sverjensky (1984 composite ore-brine

  2. Improving the performance of brine wells at Gulf Coast strategic petroleum reserve sites

    Energy Technology Data Exchange (ETDEWEB)

    Owen, L.B.; Quong, R. (eds.)

    1979-11-05

    At the request of the Department of Energy, field techniques were developed to evaluate and improve the injection of brine into wells at Strategic Petroleum Reserve (SPR) sites. These wells are necessary for the disposal of saturated brine removed from salt domes where oil is being stored. The wells, which were accepting brine at 50 percent or less of their initial design rates, were impaired by saturated brine containing particulates that deposited on the sand face and in the geologic formation next to the wellbore. Corrosion of the brine-disposal pipelines and injection wells contributed to the impairment by adding significant amounts of particulates in the form of corrosion products. When tests were implemented at the SPR sites, it was found that the poor quality of injected brines was the primary cause of impaired injection; that granular-media filtration, when used with chemical pretreatment, is an effective method for removing particulates from hypersaline brine; that satisfactory injection-well performance can be attained with prefiltered brines; and that corrosion rates can be substantially reduced by oxygen-scavenging.

  3. West Hackberry Strategic Petroleum Reserve site brine-disposal monitoring, Year I report. Volume III. Biological oceanography. Final report

    Energy Technology Data Exchange (ETDEWEB)

    DeRouen, L.R.; Hann, R.W.; Casserly, D.M.; Giammona, C.; Lascara, V.J. (eds.)

    1983-02-01

    The Department of Energy's Strategic Petroleum Reserve Program began discharging brine into the Gulf of Mexico from its West Hackberry site near Cameron, Louisiana in May 1981. The brine originates from underground salt domes being leached with water from the Intracoastal Waterway, making available vast underground storage caverns for crude oil. The effects of brine discharge on aquatic organisms are presented in this volume. The topics covered are: benthos; nekton; phytoplankton; zooplankton; and data management.

  4. Strontium isotope systematics of mixing groundwater and oil-field brine at Goose Lake in northeastern Montana, USA

    Science.gov (United States)

    Peterman, Zell E.; Thamke, Joanna N.; Futa, Kiyoto; Preston, Todd

    2012-01-01

    Groundwater, surface water, and soil in the Goose Lake oil field in northeastern Montana have been affected by Cl−-rich oil-field brines during long-term petroleum production. Ongoing multidisciplinary geochemical and geophysical studies have identified the degree and local extent of interaction between brine and groundwater. Fourteen samples representing groundwater, surface water, and brine were collected for Sr isotope analyses to evaluate the usefulness of 87Sr/86Sr in detecting small amounts of brine. Differences in Sr concentrations and 87Sr/86Sr are optimal at this site for the experiment. Strontium concentrations range from 0.13 to 36.9 mg/L, and corresponding 87Sr/86Sr values range from 0.71097 to 0.70828. The local brine has 168 mg/L Sr and a 87Sr/86Sr value of 0.70802. Mixing relationships are evident in the data set and illustrate the sensitivity of Sr in detecting small amounts of brine in groundwater. The location of data points on a Sr isotope-concentration plot is readily explained by an evaporation-mixing model. The model is supported by the variation in concentrations of most of the other solutes.

  5. Brine Migration in Heated Salt: Lessons Learned from Field Experiments

    Science.gov (United States)

    Kuhlman, K. L.; Matteo, E. N.; Mills, M.

    2017-12-01

    We summarize several interesting brine migration related phenomena hinted at in field experiments from field testing related to salt radioactive waste repositories in Germany and the US. Past heater tests in salt have shown 1) thermal-hydrological-mechanical coupling is quite strong during both heating and cooling; 2) chemical composition of brine evolves during heating, and comprises a mix of several water sources; and 3) acid gas (HCl) generation has been observed during past heater tests and may have multiple mechanisms for formation. We present a heated brine migration test design, formulated with these complexities in mind. Sandia National Laboratories is a multimission laboratory managed and operated by National Technology and Engineering Solutions of Sandia LLC, a wholly owned subsidiary of Honeywell International Inc. for the U.S. Department of Energy's National Nuclear Security Administration under contract DE-NA0003525.

  6. Environmental Impacts of Petroleum Production: Initial Results from the Osage-Skiatook Petroleum Environmental Research Sites, Osage County, Oklahoma

    Science.gov (United States)

    Kharaka, Yousif K.; Otton, James K.

    2003-01-01

    releases from active and inactive pipes and tank batteries. The leases are typical of many depleted and aging petroleum fields in Osage County, which ranks among the top oil and gas producing counties in Oklahoma with about 39,000 wells. Oil and gas production has occurred in Osage county for over one hundred years, but current production is mainly from stripper wells (averaging ~2.8 bbl/d oil and >30 bbl/d brine) that are shallow, mostly 300-700 m in depth, and produce from several sandstones of Pennsylvanian age. Results to date show that the produced water source is a Na-Ca-Cl brine (~150,000 mg/L total dissolved solids), with relatively high concentrations of Mg, Sr, and NH4, but low SO4 and H2S. With the exception of Fe and Mn, the concentrations of trace metals are low. Results also show that some and, eventually, the bulk, of inorganic salts and some dissolved organic species in the released brine from both sites will reach Skiatook Lake. Results at the 'A' site show that the salts have essentially been removed from the sandy soil which formed in a surficial layer of eolian sand, but degraded and weathered oil persists on the surface of old oil and brine pits, close to sites of old tanks, on old channels that carried oil from tanks to the oil pits and other impacted areas. Results also show a plume of high salinity water (5,000-30,600 mg/L TDS) is present at intermediate depths that extend from below the old oil and brine pits to Skiatook Lake. No liquid petroleum was found in the contaminated groundwater, but soluble petroleum byproducts, including organic acid anions and other volatile organic compounds (VOCs) are present. Results to date clearly show that significant amounts of salts from produced-water releases and petroleum hydrocarbons still remain in the soils and rocks of the impacted area after more than 60 years of natural attenuation. At the 'B' site significant amounts of produced water from the two active brine pits percolate into th

  7. Evolution of mineralizing brines in the east Tennessee Mississippi Valley-type ore field

    Energy Technology Data Exchange (ETDEWEB)

    Kesler, S.E.; Gesink, J.A.; Haynes, F.M. (Univ. of Michingan, Ann Arbor (USA))

    1989-05-01

    The east Tennessee Mississippi Valley-type (MVT) ore field contains barite-fluorite and sphalterite deposits in a continuous paleoaquifer consisting of breccia zones in the Upper Cambrian-Lower Ordovician Knox Group. Paragenetic observations and fluid inclusion compositions in these deposits indicate that the Knox paleoaquifer was invaded first by Ca-rich brines (Ca:Na about 1) that deposited fluorite and barite, and later by Na-Ca brines (Ca:Na = 0.1 to 0.5) that deposited sphalerite. Geologic relation sindicate that these brines were derived from the southeast, in the area of the Middle Ordovician Servier foreland shale basin, and that imposed by fluorite solubility indicate further that all original connate water in the Sevier basin was required to deposit the estimated flourite reserves of the ore field.Thus, the later, sphalerite-depositing brines represent recycled meteoric water from the Sevier basin or connate brines from underlying (Cambrian) shales.

  8. West Hackberry Strategic Petroleum Reserve site brine-disposal monitoring, year 1 report. Volume 1. Executive summary. Final report

    Energy Technology Data Exchange (ETDEWEB)

    DeRouen, L.R.; Hann, R.W.; Casserly, D.M.; Giammona, C.; Lascara, V.J. (eds.)

    1983-02-01

    The physical, chemical and biological attributes are described for: (1) a coastal marine environment centered about a Department of Energy Strategic Petroleum Reserve (SPR) brine disposal site located 11.4 km off the southwest coast of Louisiana; and (2) the lower Calcasieu and Sabine estuarine systems that provide leach waters for the SPR project. During the study period, the daily discharge averaged 529,000 barrels of 216 0/00 brine, representing a loading of 18,000 metric tons of salt per day. The objective of this study are: (1) characterize the environment in terms of physical, chemical and biological attributes; (2) determine if significant adverse changes in ecosystem productivity and stability of the biological community are occurring as a result of brine discharge; and (3) determine the magnitude of any change observed. This report describes the methodology and significant results of the first year's monitoring effort of the West Hackberry brine disposal site. The investigative tasks, presented as separate sections, are: Physical Oceanography, Estuarine Hydrology and Hydrography, Analysis of Discharge Plume, Water and Sediment Quality, Special Pollutant Surveys, Benthos, Nekton, Phytoplankton, Zooplankton and Data Management.

  9. West Hackberry Strategic Petroleum Reserve site brine-disposal monitoring, Year I report. Volume II. Physical and chemical oceanography. Final report

    Energy Technology Data Exchange (ETDEWEB)

    DeRouen, L.R.; Hann, R.W.; Casserly, D.M.; Giammona, C.; Lascara, V.J. (eds.)

    1983-02-01

    This project centers around the Strategic Petroleum Site (SPR) known as the West Hackberry salt dome which is located in southwestern Louisiana, and which is designed to store 241 million barrels of crude oil. Oil storage caverns are formed by injecting water into salt deposits, and pumping out the resulting brine. Studies described in this report were designed as follow-on studies to three months of pre-discharge characterization work, and include data collected during the first year of brine leaching operations. The objectives were to: (1) characterize the environment in terms of physical, chemical and biological attributes; (2) determine if significant adverse changes in ecosystem productivity and stability of the biological community are occurring as a result of brine discharge; and (3) determine the magnitude of any change observed. Contents of Volume II include: introduction; physical oceanography; estuarine hydrology and hydrography; analysis of discharge plume; and water and sediment quality.

  10. Evaluation of brine disposal from the Bryan Mound site of the strategic petroleum reserve program. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Case, Robert J.; Chittenden, Jr, Mark E.; Harper, Jr, Donald E.; Kelly, Jr, Francis J.; Loeblich, Laurel A.; McKinney, Larry D.; Minello, Thomas J.; Park, E. Taisoo; Randall, Robert E.; Slowey, J. Frank

    1981-01-01

    On March 10, 1980, the Department of Energy's Strategic Petroleum Reserve Program began leaching the Bryan Mound salt dome and discharging the resulting brine into the coastal waters off Freeport, Texas. During the months of March and April, a team of scientists and engineers from Texas A and M University conducted an intensive environmental study of the area surrounding the diffuser site. A pipeline has been laid from the Bryan Mound site to a location 12.5 statute miles (20 km) offshore. The last 3060 ft (933 m) of this pipeline is a 52-port diffuser through which brine can be discharged at a maximum rate of 680,000 barrels per day. Initially, 16 ports were open which permitted a maximum discharge rate of 350,000 barrels per day and a continuous brine discharge was achieved on March 13, 1980. The purpose of this report is to describe the findings of the project team during the intensive postdisposal study period of March and April, 1980. The major areas of investigation are physical oceanography, analysis of the discharge plume, water and sediment quality, nekton, benthos, phytoplankton, zooplankton, and data management.

  11. Chemical composition of selected Kansas brines as an aid to interpreting change in water chemistry with depth

    Science.gov (United States)

    Dingman, R.J.; Angino, E.E.

    1969-01-01

    Chemical analyses of approximately 1,881 samples of water from selected Kansas brines define the variations of water chemistry with depth and aquifer age. The most concentrated brines are found in the Permian rocks which occupy the intermediate section of the geologic column of this area. Salinity decreases below the Permian until the Ordovician (Arbuckle) horizon is reached and then increases until the Precambrian basement rocks are reached. Chemically, the petroleum brines studied in this small area fit the generally accepted pattern of an increase in calcium, sodium and chloride content with increasing salinity. They do not fit the often-predicted trend of increases in the calcium to chloride ratio, calcium content and salinity with depth and geologic age. The calcium to chloride ratio tends to be asymptotic to about 0.2 with increasing chloride content. Sulfate tends to decrease with increasing calcium content. Bicarbonate content is relatively constant with depth. If many of the hypotheses concerning the chemistry of petroleum brines are valid, then the brines studied are anomolous. An alternative lies in accepting the thesis that exceptions to these hypotheses are rapidly becoming the rule and that indeed we still do not have a valid and general hypothesis to explain the origin and chemistry of petroleum brines. ?? 1969.

  12. Uranium mobility in non-oxidizing brines: field and experimental evidence

    International Nuclear Information System (INIS)

    Giblin, A.M.; Appleyard, E.C.

    1987-01-01

    The present distribution of U in the Wollaston Sediments in Saskatchewan can be related to the movement of brines as revealed in Na-Ca-Mg-Cl-metasomes. Experiments were conducted at 60 and 200 0 C under stringently non-oxidizing conditions using solvents ranging from distilled water to a Ca-Na-K brine formulated to simulate the major element composition of the Salton Sea geothermal brines. The experiments were conducted on natural pitchblende (UOsub(2.67)) and synthetic uraninite (UOsub(2.01)). Natural pitchblende was more strongly dissolved than the synthetic uraninite, and the synthetic Salton Sea brine was a more potent solvent than distilled water, 1:4 diluted Salton Sea brine, or pure NaCl brine. Within analytical limits of detection the dissolved U is present in the uranous (U 4+ ) state. The evidence demonstrates empirically the mechanism of dissolution of naturally occurring U minerals in reduced brines and describes a geological case where this appears to have happened. (author)

  13. Brine crude oil interactions at the oil-water interface

    DEFF Research Database (Denmark)

    Chakravarty, Krishna Hara; Fosbøl, Philip Loldrup; Thomsen, Kaj

    2015-01-01

    The impact of brine salinity and its ionic composition on oil displacement efficiency has been investigated extensively in recent years due to the potential of enhanced oil recovery (EOR). Wettability alterations through relative interactions at the mineral surface have been the basis of proposed...... in enhancing oil emulsion formation by increasing interactions between polar acids and brine solutions. The results propose the potential use of HPO42- ions in reservoirs having inactive mineral surfaces. The relative oil affinity of different ions including K+, Na+, Mg2+, and Ca2+ (cations), and Cl-, SO42...... and thus reduces the interfacial viscoelasticity of the trapped oil. These results show significant correlation between oil emulsion formation and increased oil recovery. Copyright 2015; Society of Petroleum Engineers...

  14. Environmental assessment of the brine pipeline replacement for the Strategic Petroleum Reserve Bryan Mound Facility in Brazoria County, Texas

    Energy Technology Data Exchange (ETDEWEB)

    1993-09-01

    The Department of Energy (DOE) has prepared an environmental assessment (EA), DOE/EA-0804, for the proposed replacement of a deteriorated brine disposal pipeline from the Strategic Petroleum Reserve (SPR) Bryan Mound storage facility in Brazoria County, Texas, into the Gulf of Mexico. In addition, the ocean discharge outfall would be moved shoreward by locating the brine diffuser at the end of the pipeline 3.5 miles offshore at a minimum depth of 30 feet. The action would occur in a floodplain and wetlands; therefore, a floodplain/wetlands assessment has been prepared in conjunction with this EA. Based on the analyses in the EA, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969 (42 USC. 4321, et seg.). Therefore, the preparation of an Environmental Impact Statement (EIS) is not required, and the Department is issuing this Finding of No Significant Impact (FONSI). This FONSI also includes a Floodplain Statement of Findings in accordance with 10 CFR Part 1022.

  15. Environmental assessment of the brine pipeline replacement for the Strategic Petroleum Reserve Bryan Mound Facility in Brazoria County, Texas

    International Nuclear Information System (INIS)

    1993-09-01

    The Department of Energy (DOE) has prepared an environmental assessment (EA), DOE/EA-0804, for the proposed replacement of a deteriorated brine disposal pipeline from the Strategic Petroleum Reserve (SPR) Bryan Mound storage facility in Brazoria County, Texas, into the Gulf of Mexico. In addition, the ocean discharge outfall would be moved shoreward by locating the brine diffuser at the end of the pipeline 3.5 miles offshore at a minimum depth of 30 feet. The action would occur in a floodplain and wetlands; therefore, a floodplain/wetlands assessment has been prepared in conjunction with this EA. Based on the analyses in the EA, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969 (42 USC. 4321, et seg.). Therefore, the preparation of an Environmental Impact Statement (EIS) is not required, and the Department is issuing this Finding of No Significant Impact (FONSI). This FONSI also includes a Floodplain Statement of Findings in accordance with 10 CFR Part 1022

  16. West Hackberry Strategic Petroleum Reserve site brine-disposal monitoring, Year I report. Volume IV. Bibliography and supporting data for physical oceanography. Final report. [421 references

    Energy Technology Data Exchange (ETDEWEB)

    DeRouen, L.R.; Hann, R.W.; Casserly, D.M.; Giammona, C.; Lascara, V.J. (eds.)

    1983-02-01

    This project centers around the Strategic Petroleum Site (SPR) known as the West Hackberry salt dome which is located in southwestern Louisiana and which is designed to store 241 million barrels of crude oil. Oil storage caverns are formed by injecting water into salt deposits, and pumping out the resulting brine. Studies described in this report were designed as follow-on studies to three months of pre-discharge characterization work, and include data collected during the first year of brine leaching operations. The objectives were to: (1) characterize the environment in terms of physical, chemical and biological attributes; (2) determine if significant adverse changes in ecosystem productivity and stability of the biological community are occurring as a result of brine discharge; and (3) determine the magnitude of any change observed. Volume IV contains the following: bibliography; appendices for supporting data for physical oceanography, and summary of the physical oceanography along the western Louisiana coast.

  17. Petroleum-related origin for uraniferous organic-rich nodules of Southwestern Oklahoma

    International Nuclear Information System (INIS)

    Curiale, J.A.; Bloch, S.; Harrison, W.E.; Rafalska-Bloch, J.

    1983-01-01

    Geologic field relations and geochemical analyses imply a petroleum-related origin for the organic matter of uraniferous nodules in the Permian Hennessey Group red beds in Kiowa County, Oklahoma. The local presence of crude oil in the shallow subsurface and the absence of local occurrences of plant debris suggest a hydrocarbon-related origin for these nodules. Several oil seeps in the general vicinity of the study area indicate that major steep reverse faults near the nodule site may have provided vertical conduits for petroleum migration from deeper zones. Geochemical analyses of the uraniferous nodules, including infrared spectroscopy and elemental analysis, reveal characteristics of both coal and petroleum. Carbon isotopic analyses favor a petroleum-related origin. A model incorporating field and geochemical evidence is suggested whereby crude oil, migrating from depth, is initially altered near the surface to a more viscous material. Concurrently migrating uranium-bearing ground water is then stripped of its uranium by the degraded petroleum. Therefore, presence of such nodules in the shallow subsurface may suggest buried petroleum deposits. Confirmation of this model must await further study of the effects of radiation damage on organic matter

  18. West Hackberry Brine Disposal Project pre-discharge characterization. Final report

    Energy Technology Data Exchange (ETDEWEB)

    DeRouen, L.R.; Hann, R.W.; Casserly, D.M.; Giammona, C. (eds.)

    1982-01-01

    The physical, chemical and biological attributes are described for: (1) a coastal marine environment centered about a Department of Energy Strategic Petroleum Reserve (SPR) brine disposal site 11.4 km off the southwest coast of Louisiana; and (2) the lower Calcasieu and Sabine estuarine systems that provide leach waters for the SPR project. A three month sampling effort, February through April 1981, and previous investigations from the study area are integrated to establish baseline information for evaluation of impacts from brine disposal in the nearshore marine waters and from freshwater withdrawal from the coastal marsh of the Chenier Plain. January data are included for some tasks that sampled while testing and mobilizing their instruments prior to the February field effort. The study addresses the areas of physical oceanography, estuarine hydrology and hydrography, water and sediment quality, benthos, nekton, phytoplankton, zooplankton, and data management.

  19. Impacts of petroleum production on ground and surface waters: Results from the Osage-Skiatook Petroleum Environmental Research A site, Osage County Oklahoma

    Science.gov (United States)

    Kharaka, Y.K.; Thordsen, J.J.; Kakouros, E.; Herkelrath, W.N.

    2005-01-01

    As part of a multidisciplinary group of about 20 scientists, we are investigating the transport, fate, natural attenuation, and ecosystem impacts of inorganic salts and organic compounds present in releases of produced water and associated hydrocarbons at the Osage-Skiatook Petroleum Environmental Research (OSPER) sites, located in Osage County, Oklahoma. Geochemical data collected from nearby oil wells show that the produced water source is a Na-Ca-Cl brine (???150,000 mg/L total dissolved solids [TDS]), with relatively high concentrations of Mg, Sr, and NH4, but low SO4 and H2S. Results from the depleted OSPER A site show that the salts continue to be removed from the soil and surficial rocks, but degraded oil persists on the contaminated surface. Eventually, the bulk of inorganic salts and dissolved organics in the brine will reach the adjacent Skiatook Lake, a 4250-ha (10,501-ac) potable water reservoir. Repeated sampling of 44 wells show a plume of high-salinity water (2000-30,000 mg/L TDS) at intermediate depths that intersects Skiatook Lake and extends beyond the visibly impacted areas. No liquid petroleum was observed in this plume, but organic acid anions, benzene, toluene, ethylbenzene, and xylene (BTEX), and other volatile organic carbon (VOC) are present. The chemical composition of released brine is modified by sorption, mineral precipitation and dissolution, evapotranspiration, volatilization, and bacterially mediated oxidation-reduction reactions, in addition to mixing with percolating precipitation water, lake water, and pristine groundwater. Results show that only minor amounts of salt are removed by runoff, supporting the conclusion that significant amounts of salts from produced water and petroleum releases still remain in the soils and rocks of the impacted area after more than 65 yr of natural attenuation. Copyright ?? 2005. The American Association of Petroleum Geologists/Division of Environmental Geosciences. All rights reserved.

  20. Delineation of brine contamination in and near the East Poplar oil field, Fort Peck Indian Reservation, northeastern Montana, 2004-09

    Science.gov (United States)

    Thamke, Joanna N.; Smith, Bruce D.

    2014-01-01

    The extent of brine contamination in the shallow aquifers in and near the East Poplar oil field is as much as 17.9 square miles and appears to be present throughout the entire saturated zone in contaminated areas. The brine contamination affects 15–37 billion gallons of groundwater. Brine contamination in the shallow aquifers east of the Poplar River generally moves to the southwest toward the river and then southward in the Poplar River valley. The likely source of brine contamination in the shallow aquifers is brine that is produced with crude oil in the East Poplar oil field study area. Brine contamination has not only affected the water quality from privately owned wells in and near the East Poplar oil field, but also the city of Poplar’s public water-supply wells. Three water-quality types characterize water in the shallow aquifers; a fourth water-quality type in the study area characterizes the brine. Type 1 is uncontaminated water that is suitable for most domestic purposes and typically contains sodium bicarbonate and sodium/magnesium sulfate as the dominant ions. Type 2 is moderately contaminated water that is suitable for some domestic purposes, but not used for drinking water, and typically contains sodium and chloride as the dominant ions. Type 3 is considerably contaminated water that is unsuitable for any domestic purpose and always contains sodium and chloride as the dominant ions. Type 3 quality of water in the shallow aquifers is similar to Type 4, which is the brine that is produced with crude oil. Electromagnetic apparent conductivity data were collected in the 106 square-mile area and used to determine extent of brine contamination. These data were collected and interpreted in conjunction with water-quality data collected through 2009 to delineate brine plumes in the shallow aquifers. Monitoring wells subsequently were drilled in some areas without existing water wells to confirm most of the delineated brine plumes; however, several possible

  1. Weeks Island brine diffuser site study: baseline conditions and environmental assessment technical report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-12-12

    This technical report presents the results of a study conducted at two alternative brine diffuser sites (A and B) proposed for the Weeks Island salt dome, together with an analysis of the potential physical, chemical, and biological effects of brine disposal for this area of the Gulf of Mexico. Brine would result from either the leaching of salt domes to form or enlarge oil storage caverns, or the subsequent use of these caverns for crude oil storage in the Strategic Petroleum Reserve (SPR) program. Brine leached from the Weeks Island salt dome would be transported through a pipeline which would extend from the salt dome either 27 nautical miles (32 statute miles) for Site A, or 41 nautical miles (47 statute miles) for Site B, into Gulf waters. The brine would be discharged at these sites through an offshore diffuser at a sustained peak rate of 39 ft/sup 3//sec. The disposal of large quantities of brine in the Gulf could have a significant impact on the biology and water quality of the area. Physical and chemical measurements of the marine environment at Sites A and B were taken between September 1977 and July 1978 to correlate the existing environmental conditions with the estimated physical extent of tthe brine discharge as predicted by the MIT model (US Dept. of Commerce, 1977a). Measurements of wind, tide, waves, currents, and stratification (water column structure) were also obtained since the diffusion and dispersion of the brine plume are a function of the local circulation regime. These data were used to calculate both near- and far-field concentrations of brine, and may also be used in the design criteria for diffuser port configuration and verification of the plume model. Biological samples were taken to characterize the sites and to predict potential areas of impact with regard to the discharge. This sampling focused on benthic organisms and demersal fish. (DMC)

  2. Characterization of ophiolites from northern Havana-Matanzas petroleum fields using instrumental neutron activation analysis

    Energy Technology Data Exchange (ETDEWEB)

    Montero Cabrera, M.E. E-mail: montero@yakko.cimav.edu.mx; Ortueta Milan, M.; Herrera Peraza, E.F.; Herrera Hernandez, H.; Rodriguez Martinez, N.; Olivares Rieumont, S.; Lopez Reyes, M.C

    2001-01-15

    Concentrations of 16 elements from 14 serpentinitic samples from Basilio and Cantel petroleum fields were obtained by instrumental neutron activation analysis (INAA): Cr, Co, Ni, La, Nd, Sm, Eu, Gd, Tb, Ce Yb, Lu, Rb, Cs, Hf and Th. Relative INAA was performed using certified reference materials and laboratory standards. Average elemental concentrations showed that the ophiolites have a basic character, suggesting the use of a well-logging method designed for volcano-sedimentary petroleum fields.

  3. Characterization of ophiolites from northern Havana-Matanzas petroleum fields using instrumental neutron activation analysis

    International Nuclear Information System (INIS)

    Montero Cabrera, M.E.; Ortueta Milan, M.; Herrera Peraza, E.F.; Herrera Hernandez, H.; Rodriguez Martinez, N.; Olivares Rieumont, S.; Lopez Reyes, M.C.

    2001-01-01

    Concentrations of 16 elements from 14 serpentinitic samples from Basilio and Cantel petroleum fields were obtained by instrumental neutron activation analysis (INAA): Cr, Co, Ni, La, Nd, Sm, Eu, Gd, Tb, Ce Yb, Lu, Rb, Cs, Hf and Th. Relative INAA was performed using certified reference materials and laboratory standards. Average elemental concentrations showed that the ophiolites have a basic character, suggesting the use of a well-logging method designed for volcano-sedimentary petroleum fields

  4. FIELD IMPLEMENTATION PLAN FOR A WILLISTON BASIN BRINE EXTRACTION AND STORAGE TEST

    Energy Technology Data Exchange (ETDEWEB)

    Hamling, John; Klapperich, Ryan; Stepan, Daniel; Sorensen, James; Pekot, Lawrence; Peck, Wesley; Jacobson, Lonny; Bosshart, Nicholas; Hurley, John; Wilson, William; Kurz, Marc; Burnison, Shaughn; Salako, Olarinre; Musich, Mark; Botnen, Barry; Kalenze, Nicholas; Ayash, Scott; Ge, Jun; Jiang, Tao; Dalkhaa, Chantsalmaa; Oster, Benjamin; Peterson, Kyle; Feole, Ian; Gorecki, Charles; Steadman, Edward

    2016-03-31

    The Energy & Environmental Research Center (EERC) successfully completed all technical work of Phase I, including development of a field implementation plan (FIP) for a brine extraction and storage test (BEST) in the North Dakota portion of the Williston Basin. This implementation plan was commissioned by the U.S. Department of Energy (DOE) National Energy Technology Laboratory (NETL) as a proxy for managing formation pressure plumes and measuring/monitoring the movement of differential pressure and CO2 plumes in the subsurface for future saline CO2 storage projects. BEST comprises the demonstration and validation of active reservoir management (ARM) strategies and extracted brine treatment technologies. Two prospective commercial brine injection sites were evaluated for BEST to satisfy DOE’s goals. Ultimately, an active saltwater disposal (SWD) site, Johnsons Corner, was selected because it possesses an ideal combination of key factors making it uniquely suited to host BEST. This site is located in western North Dakota and operated by Nuverra Environmental Solutions (Nuverra), a national leader in brine handling, treatment, and injection. An integrated management approach was used to incorporate local and regional geologic characterization activities with geologic and simulation models, inform a monitoring, verification, and accounting (MVA) plan, and to conduct a risk assessment. This approach was used to design a FIP for an ARM schema and an extracted brine treatment technology test bed facility. The FIP leverages an existing pressure plume generated by two commercial SWD wells. These wells, in conjunction with a new brine extraction well, will be used to conduct the ARM schema. Results of these tests will be quantified based on their impact on the performance of the existing SWD wells and the surrounding reservoir system. Extracted brine will be injected into an underlying deep saline formation through a new injection well. The locations of proposed

  5. West Hackberry Strategic Petroleum Reserve site brine disposal monitoring, Year I report. Volume V. Supporting data for estuarine hydrology, discharge plume analysis, chemical oceanography, biological oceanography, and data management. Final report

    Energy Technology Data Exchange (ETDEWEB)

    DeRouen, L.R.; Hann, R.W.; Casserly, D.M.; Giammona, C.; Lascara, V.J. (eds.)

    1983-02-01

    This project centers around the Strategic Petroleum Site (SPR) known as the West Hackberry salt dome which located in southwestern Louisiana, and which is designed to store 241 million barrels of crude oil. Oil storage caverns are formed by injecting water into salt deposits, and pumping out the resulting brine. Studies described in this report were designed as follow-on studies to three months of pre-discharge characterization work, and include data collected during the first year of brine leaching operations. The objectives were to: (1) characterize the environment in terms of physical, chemical and biological attributes; (2) determine if significant adverse changes in ecosystem productivity and stability of the biological community are occurring as a result of brine discharge; and (3) determine the magnitude of any change observed. Volume V contains appendices for the following: supporting data for estuarine hydrology and hydrography; supporting data analysis of discharge plume; supporting data for water and sediment chemistry; CTD/DO and pH profiles during biological monitoring; supporting data for nekton; and supporting data for data management.

  6. Laboratory and field studies on an Indian strain of the brine shrimp Artemia

    Digital Repository Service at National Institute of Oceanography (India)

    Royan, J.P.

    The Tuticorin strain of the brine shrimp @iArtemia@@ was studied under both laboratory and field conditions. Studies on the survival of the nauplii at different temperatures and salinities revealed that the nauplii preferred a salinity of 35 ppt...

  7. Modelling CO2-Brine Interfacial Tension using Density Gradient Theory

    KAUST Repository

    Ruslan, Mohd Fuad Anwari Che

    2018-03-01

    Knowledge regarding carbon dioxide (CO2)-brine interfacial tension (IFT) is important for petroleum industry and Carbon Capture and Storage (CCS) strategies. In petroleum industry, CO2-brine IFT is especially importance for CO2 – based enhanced oil recovery strategy as it affects phase behavior and fluid transport in porous media. CCS which involves storing CO2 in geological storage sites also requires understanding regarding CO2-brine IFT as this parameter affects CO2 quantity that could be securely stored in the storage site. Several methods have been used to compute CO2-brine interfacial tension. One of the methods employed is by using Density Gradient Theory (DGT) approach. In DGT model, IFT is computed based on the component density distribution across the interface. However, current model is only applicable for modelling low to medium ionic strength solution. This limitation is due to the model only considers the increase of IFT due to the changes of bulk phases properties and does not account for ion distribution at interface. In this study, a new modelling strategy to compute CO2-brine IFT based on DGT was proposed. In the proposed model, ion distribution across interface was accounted for by separating the interface to two sections. The saddle point of tangent plane distance where ( ) was defined as the boundary separating the two sections of the interface. Electrolyte is assumed to be present only in the second section which is connected to the bulk liquid phase side. Numerical simulations were performed using the proposed approach for single and mixed salt solutions for three salts (NaCl, KCl, and CaCl2), for temperature (298 K to 443 K), pressure (2 MPa to 70 MPa), and ionic strength (0.085 mol·kg-1 to 15 mol·kg-1). The simulation result shows that the tuned model was able to predict with good accuracy CO2-brine IFT for all studied cases. Comparison with current DGT model showed that the proposed approach yields better match with the experiment data

  8. Organic geochemistry of deep ground waters from the Palo Duro Basin, Texas: implications for radionuclide complexation, ground-water origin, and petroleum exploration

    International Nuclear Information System (INIS)

    Means, J.L.; Hubbard, N.J.

    1985-05-01

    This report describes the organic geochemistry of 11 ground-water samples from the Palo Duro Basin, Texas and discusses the implications of their organic geochemical compositions in terms of radionuclide complexation, ground-water origin, and the petroleum potential of two candidate repository sites in Deaf Smith and Swisher Counties. Short-chain aliphatic acid anions are the principal organic constituents present. Stability constant data and simple chemical equilibria calculations suggest that short-chain aliphatic acids are relatively weak complexing agents. The extent of complexation of a typical actinide by selected inorganic ligands present in these brines is expected to far outweigh actinide complexation by the aliphatic acid anions. Various lines of evidence suggest that some portion of the bromide concentrations in the brines is derived from the same source as the short-chain aliphatic acid anions. When the postulated organic components are subtracted from total bromide concentrations, the origins of the Palo Duro brines, based on chloride versus bromide relationships, appear largely consistent with origins based on isotopic evidence. The short-chain aliphatic acid anion content of the Palo Duro brines is postulated to have been much greater in the geologic past. Aliphatic acid anions are but one of numerous petroleum proximity indicators, which consistently suggest a greater petroleum exploration potential for the area surrounding the Swisher County site than the region encompassing the candidate site in Deaf Smith County. Short-chain aliphatic acid anions appear to provide a useful petroleum exploration tool as long as the complex reactions that may dimish their concentrations in ground water are recognized. 71 refs., 10 figs., 10 tabs

  9. Uranium-thorium series radionuclides in brines and reservoir rocks from two deep geothermal boreholes in the Salton Sea Geothermal Field, southeastern California

    Science.gov (United States)

    Zukin, Jeffrey G.; Hammond, Douglas E.; Teh-Lung, Ku; Elders, Wilfred A.

    1987-10-01

    Naturally occurring U and Th series radionuclides have been analyzed in high temperature brines (~300°C, 25 wt% dissolved solids) and associated rocks from two deep geothermal wells located on the northeastern margin of the Salton Sea Geothermal Field (SSGF). These data are part of a study of the SSGF as a natural analog of possible radionuclide behavior near a nuclear waste repository constructed in salt beds, and permit evaluation of some characteristics of water-rock interaction in the SSGF. Rock/Brine concentration ratios ( Rc = (dpm/ g) rock/(dpm/ g) brine) were found to vary from near unity for isotopes of Ra, Pb and Rn to about 5 × 10 5 for 232Th. The high sorptivity of 232Th is closely followed by that of 238U and 234U ( Rc ~ 5 × 10 4), suggesting that U is retained in the +4 oxidation state by the reducing conditions in the brines. The relatively high solubility of 210Pb and 212Pb is attributed to formation of chloride complexes, while the high Ra solubility is attributed to chloride complexing, a lack of suitable adsorption sites due to the high brine salinity and temperature, and the reducing conditions that prevent MnO 2 and RaSO 4 from forming. The 228Ra /226Ra ratios in the brines are approximately equal to those of their parents ( 232Th /230Th ) in associated rocks, indicating that Ra equilibration in the brine-rock system is achieved within the mean life of 228Ra (8.3 years). The 224Ra /228Ra ratios in these brines are about 0.7, indicating that either (1) brine composition is not homogeneous and 224Ra decays in fracture zones deficient in Ra and Th as the brine travels to the wellhead or (2) Ra equilibration in the brine-host rock system is not complete within the mean life of 224Ra (5.2 days) because the desorption of 224Ra from the solid phase is impeded. The 228Ac /228Ra activity ratio in the SSGF brines studied is <0.1, and from this ratio the residence time of 228Ac in the brine before sorption onto solid surfaces is estimated to be <70

  10. Modeling Coupled THM Processes and Brine Migration in Salt at High Temperatures

    International Nuclear Information System (INIS)

    Rutqvist, Jonny; Blanco-Martin, Laura; Molins, Sergi; Trebotich, David; Birkholzer, Jens

    2015-01-01

    In this report, we present FY2015 progress by Lawrence Berkeley National Laboratory (LBNL) related to modeling of coupled thermal-hydrological-mechanical-chemical (THMC) processes in salt and their effect on brine migration at high temperatures. This is a combined milestone report related to milestone Salt R&D Milestone ''Modeling Coupled THM Processes and Brine Migration in Salt at High Temperatures'' (M3FT-15LB0818012) and the Salt Field Testing Milestone (M3FT-15LB0819022) to support the overall objectives of the salt field test planning.

  11. Modeling Coupled THM Processes and Brine Migration in Salt at High Temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Rutqvist, Jonny [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Blanco-Martin, Laura [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Molins, Sergi [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Trebotich, David [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Birkholzer, Jens [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2015-09-01

    In this report, we present FY2015 progress by Lawrence Berkeley National Laboratory (LBNL) related to modeling of coupled thermal-hydrological-mechanical-chemical (THMC) processes in salt and their effect on brine migration at high temperatures. This is a combined milestone report related to milestone Salt R&D Milestone “Modeling Coupled THM Processes and Brine Migration in Salt at High Temperatures” (M3FT-15LB0818012) and the Salt Field Testing Milestone (M3FT-15LB0819022) to support the overall objectives of the salt field test planning.

  12. Geological implications of radium and helium in oil-field brines: observations, inferences and speculations

    International Nuclear Information System (INIS)

    Lerche, I.

    1993-01-01

    The 1600 yr half-life of radium restricts the time and thus the distance over which radium can migrate in sediments. The dominant source of unsupported radium in sandstone reservoir brines must then be close by and is likely in shales adjacent to the oil-field reservoirs. The chemical similarity of calcium and radium can be used to argue for a local shale-source contribution to the calcium in reservoir sands -suggesting the probability of calcite cementation early in the sedimentary sequence. Helium production by radium decay increases with time. Concentrations of helium found in reservoir oil field brines are then used to suggest that: (a) such reservoirs are dominantly closed systems over geological times; (b) neither methane nor helium in the reservoirs have migrated any significant distance; and (c) the mechanism responsible for the observed helium in the brine is a continuous on-going process operative today. Diagenetic studies should then deal with both sands and shales interdependently, the two are not separable. Shales control the transport mechanisms of migration so that the primary migration of hydrocarbons, the result of kerogen catagenesis in shales, should occur sufficiently early in the sedimentary sequence in order to avoid exclusion from the reservoir by calcite cementation in association with radium transport. (author)

  13. Strontium isotope evidence on the history of oilfield brines, Mediterranean Coastal Plain, Israel

    International Nuclear Information System (INIS)

    Starinsky, A.; Bielski, M.; Lazar, B.; Steinitz, G.; Raab, M.

    1983-01-01

    The isotopic composition of Sr in oil field brines from the Mediterranean Coastal Plain was determined in 18 drillholes. The brines are characterized by salinities ranging from 35 to 93 g/l (TDS), Sr from 28 to 350 mg/l, Sr/Ca molar ratios from 0.011 to 0.053 and 87 Sr/ 86 Sr ratios from 0.7075 to 0.7090. E and A = 0.7081 +- 0.0004 (2σ). The brines are classified into two groups: (a) Mavqi'im group - brines with relatively high 87 Sr/ 86 Sr ratios, sampled from clastics, dolomites and anhydrites of Upper Miocene age. (b) Heletz group - brines with relatively low 87 Sr/ 86 Sr ratios, sampled from sandstones and dolomites of Lower Cretaceous age. Equations were derived to show the relations between 87 Sr/ 86 Sr ratio of the brines and the processes through which they evolved. It is suggested that both groups of brines originated from Mediterranean evaporated seawater during the Messinian desiccation. The strontium isotope composition of the seawater is reflected in that of both groups of brines, the Mavqi'im group containing the original 87 Sr/ 86 Sr ratio. The Heletz group evolved later on, through exchange reactions of those primary brines with a carbonate sequence of Cretaceous age and consequently new 87 Sr/ 86 Sr ratios could have been developed. (author)

  14. Investigation of an innovative technology for oil-field brine treatment

    Energy Technology Data Exchange (ETDEWEB)

    Miskovic, D; Dalmacija, B; Hain, Z; Karlovic, E; Maric, S; Uzelac, N [Inst. of Chemistry, Faculty of Sciences, V. Vlahovica 2 (YU)

    1989-01-01

    Various aspects of an innovative technology for oil field brine treatment were investigated on a laboratory scale. The both free and dispersed oily matter were separated by gravitation and sedimentation. Apart from the physico-chemical oil removal process, special attention was paid to different variants of improved microbiological treatment: dilution with fresh water and application of powdered activated carbon (PAC). Advanced treatment was carried out on granular biological activated carbon (GBAC). A technological scheme for complete treatment was proposed. (author).

  15. Effect of gas field production and CO2 injection on brine flow and salt precipitation

    NARCIS (Netherlands)

    Loeve, D.; Tambach, T.J.; Hofstee, C.; Plug, W.J.; Maas, J.

    2012-01-01

    This paper reports modeling of gas field produc-tion and CO2 injection from a theoretical reser-voir based on characteristics of the P18 gas field in the Dutch offshore, which consists of four geological deposits with different petrophysical properties. We especially focus on the brine flow during

  16. Subsurface transport of inorganic and organic solutes from experimental road spreading of oil-field brine

    International Nuclear Information System (INIS)

    Bair, E.S.; Digel, R.K.

    1990-01-01

    A study designed to evaluate ground water quality changes resulting from spreading oil-field brine on roads for ice and dust control was conducted using a gravel roadbed that received weekly applications of brine eight times during the winter phase and 11 times during the summer phase of the study. A network of 11 monitoring wells and five pressure-vacuum lysimeters was installed to obtain ground water and soil water samples. Thirteen sets of water-quality samples were collected and analyzed for major ions, trace metals, and volatile organic compounds. Two sets of samples were taken prior to brine spreading, four sets during winter-phase spreading, five sets during summer-phase spreading, and two sets during the interim between the winter and summer phases. A brine plume delineated by elevated specific-conductance values and elevated chloride concentrations in ground water samples to exceed US EPA public drinking-water standards by two-fold during the winter phase and five-fold during the summer phase. No other major ions, trace metals, or volatile organic compounds exceeded the standards during the winter or summer phases. More than 99% dilution of the solutes in the brine occurred between the roadbed surface and the local ground water flow system. Further attenuation of calcium, sodium, potassium, and strontium resulted from adsorption, whereas further attenuation of benzene resulted from volatilization and adsorption

  17. Strontium isotope detection of brine contamination in the East Poplar oil field, Montana

    Science.gov (United States)

    Peterman, Zell E.; Thamke, Joanna N.; Futa, Kiyoto; Oliver, Thomas A.

    2010-01-01

    Brine contamination of groundwater in the East Poplar oil field was first documented in the mid-1980s by the U.S. Geological Survey by using hydrochemistry, with an emphasis on chloride (Cl) and total dissolved solids concentrations. Supply wells for the City of Poplar are located downgradient from the oil field, are completed in the same shallow aquifers that are documented as contaminated, and therefore are potentially at risk of being contaminated. In cooperation with the Office of Environmental Protection of the Fort Peck Tribes, groundwater samples were collected in 2009 and 2010 from supply wells, monitor wells, and the Poplar River for analyses of major and trace elements, including strontium (Sr) concentrations and isotopic compositions. The ratio of strontium-87 to strontium-86 (87Sr/86Sr) is used extensively as a natural tracer in groundwater to detect mixing among waters from different sources and to study the effects of water/rock interaction. On a plot of the reciprocal strontium concentration against the 87Sr/86Sr ratio, mixtures of two end members will produce a linear array. Using this plotting method, data for samples from most of the wells, including the City of Poplar wells, define an array with reciprocal strontium values ranging from 0.08 to 4.15 and 87Sr/86Sr ratios ranging from 0.70811 to 0.70828. This array is composed of a brine end member with an average 87Sr/86Sr of 0.70822, strontium concentrations in excess of 12.5 milligrams per liter (mg/L), and chloride concentrations exceeding 8,000 mg/L mixing with uncontaminated water similar to that in USGS06-08 with 18.0 mg/L chloride, 0.24 mg/L strontium, and a 87Sr/86Sr ratio of 0.70811. The position of samples from the City of Poplar public-water supply wells within this array indicates that brine contamination has reached all three wells. Outliers from this array are EPU-4G (groundwater from the Cretaceous Judith River Formation), brine samples from disposal wells (Huber 5-D and EPU 1-D

  18. Applied field test procedures on petroleum release sites

    International Nuclear Information System (INIS)

    Gilbert, G.; Nichols, L.

    1995-01-01

    The effective remediation of petroleum contaminated soils and ground water is a significant issue for Williams Pipe Line Co. (Williams): costing $6.8 million in 1994. It is in the best interest, then, for Williams to adopt approaches and apply technologies that will be both cost-effective and comply with regulations. Williams has found the use of soil vapor extraction (SVE) and air sparging (AS) field test procedures at the onset of a petroleum release investigation/remediation accomplish these goals. This paper focuses on the application of AS/SVE as the preferred technology to a specific type of remediation: refined petroleum products. In situ field tests are used prior to designing a full-scale remedial system to first validate or disprove initial assumptions on applicability of the technology. During the field test, remedial system design parameters are also collected to tailor the design and operation of a full-scale system to site specific conditions: minimizing cost and optimizing effectiveness. In situ field tests should be designed and operated to simulate as close as possible the operation of a full-scale remedial system. The procedures of an in situ field test will be presented. The results of numerous field tests and the associated costs will also be evaluated and compared to full-scale remedial systems and total project costs to demonstrate overall effectiveness. There are many advantages of As/SVE technologies over conventional fluid extraction or SVE systems alone. However, the primary advantage is the ability to simultaneously reduce volatile and biodegradable compound concentrations in the phreatic, capillary fringe, and unsaturated zones

  19. Results for the Brine Evaporation Bag (BEB) Brine Processing Test

    Science.gov (United States)

    Delzeit, Lance; Flynn, Michael; Fisher, John; Shaw, Hali; Kawashima, Brian; Beeler, David; Howard, Kevin

    2015-01-01

    The recent Brine Processing Test compared the NASA Forward Osmosis Brine Dewatering (FOBD), Paragon Ionomer Water Processor (IWP), UMPQUA Ultrasonic Brine Dewatering System (UBDS), and the NASA Brine Evaporation Bag (BEB). This paper reports the results of the BEB. The BEB was operated at 70 deg C and a base pressure of 12 torr. The BEB was operated in a batch mode, and processed 0.4L of brine per batch. Two different brine feeds were tested, a chromic acid-urine brine and a chromic acid-urine-hygiene mix brine. The chromic acid-urine brine, known as the ISS Alternate Pretreatment Brine, had an average processing rate of 95 mL/hr with a specific power of 5kWhr/L. The complete results of these tests will be reported within this paper.

  20. Brine Sampling and Evaluation Program: Phase 1 report

    International Nuclear Information System (INIS)

    Deal, D.E.; Case, J.B.

    1987-01-01

    This interim report presents preliminary data obtained in the course of the WIPP Brine Sampling and Evaluation Program. The investigations focus on the brine present in the near-field environment around the WIPP underground workings. Although the WIPP underground workings are considered dry, small amounts of brine are present. This amount of brine is not unexpected in rocks of marine sedimentary origin. Part of that brine can and does migrate into the repository in response to pressure gradients, at essentially isothermal conditions. These small volumes of brine have little effect on the day-to-day operations, but are pervasive throughout the repository and may contribute enough moisture over a period of years to affect resaturation and repressurization after sealing and closure. Gas bubbles are observed in many of the brine occurrences. Gas is also known to exsolve from solution as the brine is poured from container to container. 68 refs., 9 figs., 2 tabs

  1. A review of modern instrumental methods of elemental analysis of petroleum related material. Part 2

    International Nuclear Information System (INIS)

    Nadkarni, R.A.

    1991-01-01

    In this paper a review is presented of the state of the art in elemental analysis of petroleum-related materials (crude oil, gasoline, additives, and lubricants) using modern instrumental analysis techniques. The major instrumental techniques used for elemental analysis of petroleum products include atomic absorption spectrometry (both with flame and with graphite furnace atomizer), inductively coupled plasma atomic emission spectrometry, ion chromatography, microelemental methods, neutron activation, spark source mass spectrometry, and x-ray fluorescence. Each of these techniques is compared for its advantages, disadvantages, and typical applications in the petroleum field

  2. Evolution of hydrologic systems and brine geochemistry in a deforming salt medium: Data from WIPP brine seeps

    International Nuclear Information System (INIS)

    Deal, D.E.; Roggenthen, W.M.

    1991-01-01

    The Brine Sampling and Evaluation Program (BSEP) is a formalized continuation of studies that began in 1982 as part of the Site Validation Program. The program was established in 1985. The mission was to document and investigate the origins, hydraulic characteristics, extent, and composition of brine occurrences in the Permian Salado Formation and the seepage of that brine into the WIPP excavations. This document focuses on the cumulative data obtained from the BSEP. The overall activities of the BSEP described and quantified the brine. It includes documentation and study of brine inflow into boreholes in the facility. The BSEP investigated the occurrence and development of brine weeps, crusts, and brine geochemistry. The presence of salt-tolerant bacteria in the workings was recorded and their possible interactions with experiments and operations, was assessed. The formation properties associated with the occurrence of brine was characterized. The determination of formation properties included the water content of various geologic units, direct examination of these units in boreholes using a video camera system, and measurement of electrical properties relatable to the brine contents. Modeling examined the interaction of salt deformation near the workings and the flow of brine through the deforming rocks. 34 refs

  3. Geomechanical Model Calibration Using Field Measurements for a Petroleum Reserve

    Science.gov (United States)

    Park, Byoung Yoon; Sobolik, Steven R.; Herrick, Courtney G.

    2018-03-01

    A finite element numerical analysis model has been constructed that consists of a mesh that effectively captures the geometries of Bayou Choctaw (BC) Strategic Petroleum Reserve (SPR) site and multimechanism deformation (M-D) salt constitutive model using the daily data of actual wellhead pressure and oil-brine interface location. The salt creep rate is not uniform in the salt dome, and the creep test data for BC salt are limited. Therefore, the model calibration is necessary to simulate the geomechanical behavior of the salt dome. The cavern volumetric closures of SPR caverns calculated from CAVEMAN are used as the field baseline measurement. The structure factor, A 2, and transient strain limit factor, K 0, in the M-D constitutive model are used for the calibration. The value of A 2, obtained experimentally from BC salt, and the value of K 0, obtained from Waste Isolation Pilot Plant salt, are used for the baseline values. To adjust the magnitude of A 2 and K 0, multiplication factors A 2 F and K 0 F are defined, respectively. The A 2 F and K 0 F values of the salt dome and salt drawdown skins surrounding each SPR cavern have been determined through a number of back analyses. The cavern volumetric closures calculated from this model correspond to the predictions from CAVEMAN for six SPR caverns. Therefore, this model is able to predict behaviors of the salt dome, caverns, caprock, and interbed layers. The geotechnical concerns associated with the BC site from this analysis will be explained in a follow-up paper.

  4. Biological treatment process for removing petroleum hydrocarbons from oil field produced waters

    Energy Technology Data Exchange (ETDEWEB)

    Tellez, G.; Khandan, N.

    1995-12-31

    The feasibility of removing petroleum hydrocarbons from oil fields produced waters using biological treatment was evaluated under laboratory and field conditions. Based on previous laboratory studies, a field-scale prototype system was designed and operated over a period of four months. Two different sources of produced waters were tested in this field study under various continuous flow rates ranging from 375 1/D to 1,800 1/D. One source of produced water was an open storage pit; the other, a closed storage tank. The TDS concentrations of these sources exceeded 50,000 mg/l; total n-alkanes exceeded 100 mg/l; total petroleum hydrocarbons exceeded 125 mg/l; and total BTEX exceeded 3 mg/l. Removals of total n-alkanes, total petroleum hydrocarbons, and BTEX remained consistently high over 99%. During these tests, the energy costs averaged $0.20/bbl at 12 bbl/D.

  5. State-of-the-art review of brine migration studies in salt. Technical memorandum report RSI-0075

    International Nuclear Information System (INIS)

    Gnirk, P.F.; Krause, W.B.; Fossum, A.F.

    1981-09-01

    This report provides a state-of-the-art review of brine migration studies in rock salt. Emphasis is placed on the review of literature relating to brine migration phenomena around nuclear waste canisters. This review includes experimental work which has been conducted in the laboratory and in the field. In addition to the literature review, some additional thoughts on brine migration are given and a series of laboratory experiments is proposed. The proposed laboratory experiments are designed to determine whether or not a relationship exists between brine migration and temperature, temperature gradient and stress in rock salt. 34 references, 9 figures, 3 tables

  6. Novel Cleanup Agents Designed Exclusively for Oil Field Membrane Filtration Systems Low Cost Field Demonstrations of Cleanup Agents in Controlled Experimental Environments

    Energy Technology Data Exchange (ETDEWEB)

    David Burnett; Harold Vance

    2007-08-31

    The goal of our project is to develop innovative processes and novel cleaning agents for water treatment facilities designed to remove fouling materials and restore micro-filter and reverse osmosis (RO) membrane performance. This project is part of Texas A&M University's comprehensive study of the treatment and reuse of oilfield brine for beneficial purposes. Before waste water can be used for any beneficial purpose, it must be processed to remove contaminants, including oily wastes such as residual petroleum hydrocarbons. An effective way of removing petroleum from brines is the use of membrane filters to separate oily waste from the brine. Texas A&M and its partners have developed highly efficient membrane treatment and RO desalination for waste water including oil field produced water. We have also developed novel and new cleaning agents for membrane filters utilizing environmentally friendly materials so that the water from the treatment process will meet U.S. EPA drinking water standards. Prototype micellar cleaning agents perform better and use less clean water than alternate systems. While not yet optimized, the new system restores essentially complete membrane flux and separation efficiency after cleaning. Significantly the amount of desalinated water that is required to clean the membranes is reduced by more than 75%.

  7. In situ brine migration experiments at the Avery Island salt mine

    International Nuclear Information System (INIS)

    Krause, W.B.; Van Sambeek, L.L.; Stickney, R.G.

    1980-01-01

    An in situ brine movement study was conducted at the Avery Island Salt Mine of the International Salt Company in southwestern Louisiana. The objective of the in situ experiments was to relate field measurements to previously determined laboratory and analytical results for the purpose of determining the rate and amount of brine movement through dome salt when subjected to heating. The heating in the experiments was provided by electrical heaters emplaced in the salt mine floor. An understanding of thermally induced brine movement is essential from the standpoint of identifying conditions which may influence the physical integrity of the nuclear waste canisters or impede the functional performance of the waste package system in a nuclear waste repository in geologic salt. 28 refs

  8. Near-field environment research at PNL relevant to brine migration phenomena

    International Nuclear Information System (INIS)

    Pederson, L.R.; Gray, W.J.; Hodges, F.N.

    1987-01-01

    Heat and radiation resulting from emplacement of a high level nuclear waste package in a repository in salt will cause physical and chemical changes in the host rock and any brines present. These changes may alter the performance of waste package materials. Gamma radiolysis decomposes water into hydrogen and oxygen, hydrogen peroxide, and various other free radical and ionic species. Gamma ray irradiation of rock salt decomposes that salt to sodium metal colloids and neutral chlorine (unknown form), changing both its physical and chemical properties. Sodium metal will react, if contacted by water, to form sodium hydroxide plus hydrogen gas, while chlorine will react to form hydrochloric plus hypochlorous acids. If irradiated salts are completely dissolved, little impact on the chemical environment is expected because the acids and bases formed will neutralize each other. Heat from the waste package can alter the chemistry of the host rock. Changes in temperature can also alter the chemistry of brines by precipitation of phases with retrograde solubility, addition of more soluble salt components to the brine, and by reaction with clays and other impurities in the salt. Some of these reactions could be accompanied by significant shifts in the pH. In experiments to date, no important changes in chemistry have been observed when typical Permian Basin intrusion or inclusion brines were heated up to 150 0 C with no excess site-specific salt present. When excess salt was included, acidic shifts were noted, increasing with brine-salt interaction time and temperature

  9. Mission improbable: Does petroleum-related aid address the resource curse?

    International Nuclear Information System (INIS)

    Kolstad, Ivar; Wiig, Arne; Williams, Aled

    2009-01-01

    Petroleum-related aid programmes and projects are a key part of donor activities in oil-rich developing countries. This paper critically assesses petroleum-related aid activities, using the Norwegian Oil for Development programme as a main case. Recent research suggests that institutions, or governance, are essential in averting a resource curse. While governance issues are beginning to receive more attention in these types of programmes, they still form a minor part of programme activities. The narrow sector focus that characterizes petroleum-related aid makes it unlikely that it will produce the higher order institutional changes needed to lift the resource curse. Petroleum-related aid activities address the issue of corruption only to a limited extent. Given the commercial and political interests of donor countries, questions about the integrity and credibility of these types of programmes can be raised

  10. Applications of T-ray spectroscopy in the petroleum field

    Science.gov (United States)

    Al-Douseri, Fatemah M.

    2005-11-01

    Because of heavy usage of petroleum products, which are the main source of energy in daily life and industry, a fast, reliable, and portable analysis system is needed to complement traditional techniques. Terahertz (THz) radiation, or T-rays, is electromagnetic radiation in the 0.1 to 10 THz frequency range. One unique attribute of T-rays is their ability to sensitively measure the induced molecular dipole moments in non-polar liquids such as aromatics, which make up the majority of the contents of many petroleum products. This information can lead to several applications in petroleum analysis. The application of T-rays to petroleum product analysis has the potential to make a significant impact in the petroleum field. In this dissertation, I show the first use of T-ray time-domain spectroscopy and Fourier transform infrared (FTIR) spectroscopy techniques for petroleum product analysis. I report on the feasibility of analyzing selected petroleum products, including gasoline, diesel, lubricating oil, and selected compounds of toluene, ethylbenzene, and xylene (BTEX). With the use of a T-ray time-domain spectrometer. I demonstrate that gasolines with different octane numbers and diesel all show specific absorption coefficients and refractive indexes in the spectral range from 0.5 to 2.0 THz. Furthermore, I report the qualitative and quantitative analysis of selected BTEX components in gasoline and diesel using FTIR spectroscopy in the 50 to 650 cm-1 region. I distinguish gasolines with different octane numbers from diesel and lubricating oil according to their different spectral features. I also determine the concentration of (o, m, p) xylene isomers in gasoline according to their specific absorption bands. The experimental results in this thesis, imply that linking between the knowledge of petroleum products and the development of T-ray spectrometer with the cooperation of industry might translate the T-ray spectroscopic system into a real world application in

  11. Origin of the yellow brine and the black brine in Sichuan Basin

    International Nuclear Information System (INIS)

    Wang Dongsheng

    1988-01-01

    The spring water, geothermal water and Cretaceous brine in the outer zone of the Sichuan Basin has the Craig relationship, and they are cycling waters. The brine in the inner zone is mainly metasedimentary water. A basic feature of them is poor in 2 H, but rich in 18 O. The δD-values of the yellow brine in Jurassic and Upper Triassic aquifer of continental facies varies from -62.25 to -22.4, and the δ 18 O-values are -6.72 - +6.02. The δD-values of the black brine in marine aquifer (T 2 ,T 1 ,P,C,O and so on) varies from -49 to -25.1, and the 18 O values are +3.89 - +6.14. The δD of yellow brine is similar to that of meteoric water, and the δD of the black brine is around that of crystallization water expelled from gypsum by anhydritization. Increases of salinity in Jurassic yellow brine result primarily from the evapotranspiration process. The salinity in Upper Triassic yellow brine in Aa sub-area originated from underlying rock salt which was leached by paleometeoric water. Triassic black brine derived from the mixing of the crystallization water leached from rock salt with the residual sea water after salt crystallization. In Zhigong, the composition of yellow brine has mainly been changed by the mixing of the yellow brine with the black brine. (author). 2 refs, 2 figs, 2 tabs

  12. Succession in the petroleum reservoir microbiome through an oil field production lifecycle.

    Science.gov (United States)

    Vigneron, Adrien; Alsop, Eric B; Lomans, Bartholomeus P; Kyrpides, Nikos C; Head, Ian M; Tsesmetzis, Nicolas

    2017-09-01

    Subsurface petroleum reservoirs are an important component of the deep biosphere where indigenous microorganisms live under extreme conditions and in isolation from the Earth's surface for millions of years. However, unlike the bulk of the deep biosphere, the petroleum reservoir deep biosphere is subject to extreme anthropogenic perturbation, with the introduction of new electron acceptors, donors and exogenous microbes during oil exploration and production. Despite the fundamental and practical significance of this perturbation, there has never been a systematic evaluation of the ecological changes that occur over the production lifetime of an active offshore petroleum production system. Analysis of the entire Halfdan oil field in the North Sea (32 producing wells in production for 1-15 years) using quantitative PCR, multigenic sequencing, comparative metagenomic and genomic bins reconstruction revealed systematic shifts in microbial community composition and metabolic potential, as well as changing ecological strategies in response to anthropogenic perturbation of the oil field ecosystem, related to length of time in production. The microbial communities were initially dominated by slow growing anaerobes such as members of the Thermotogales and Clostridiales adapted to living on hydrocarbons and complex refractory organic matter. However, as seawater and nitrate injection (used for secondary oil production) delivered oxidants, the microbial community composition progressively changed to fast growing opportunists such as members of the Deferribacteres, Delta-, Epsilon- and Gammaproteobacteria, with energetically more favorable metabolism (for example, nitrate reduction, H 2 S, sulfide and sulfur oxidation). This perturbation has profound consequences for understanding the microbial ecology of the system and is of considerable practical importance as it promotes detrimental processes such as reservoir souring and metal corrosion. These findings provide a new

  13. Estimating decades-long trends in petroleum field energy return on investment (EROI) with an engineering-based model

    Science.gov (United States)

    Tripathi, Vinay S.

    2017-01-01

    This paper estimates changes in the energy return on investment (EROI) for five large petroleum fields over time using the Oil Production Greenhouse Gas Emissions Estimator (OPGEE). The modeled fields include Cantarell (Mexico), Forties (U.K.), Midway-Sunset (U.S.), Prudhoe Bay (U.S.), and Wilmington (U.S.). Data on field properties and production/processing parameters were obtained from a combination of government and technical literature sources. Key areas of uncertainty include details of the oil and gas surface processing schemes. We aim to explore how long-term trends in depletion at major petroleum fields change the effective energetic productivity of petroleum extraction. Four EROI ratios are estimated for each field as follows: The net energy ratio (NER) and external energy ratio (EER) are calculated, each using two measures of energy outputs, (1) oil-only and (2) all energy outputs. In all cases, engineering estimates of inputs are used rather than expenditure-based estimates (including off-site indirect energy use and embodied energy). All fields display significant declines in NER over the modeling period driven by a combination of (1) reduced petroleum production and (2) increased energy expenditures on recovery methods such as the injection of water, steam, or gas. The fields studied had NER reductions ranging from 46% to 88% over the modeling periods (accounting for all energy outputs). The reasons for declines in EROI differ by field. Midway-Sunset experienced a 5-fold increase in steam injected per barrel of oil produced. In contrast, Prudhoe Bay has experienced nearly a 30-fold increase in amount of gas processed and reinjected per unit of oil produced. In contrast, EER estimates are subject to greater variability and uncertainty due to the relatively small magnitude of external energy investments in most cases. PMID:28178318

  14. Estimating decades-long trends in petroleum field energy return on investment (EROI) with an engineering-based model.

    Science.gov (United States)

    Tripathi, Vinay S; Brandt, Adam R

    2017-01-01

    This paper estimates changes in the energy return on investment (EROI) for five large petroleum fields over time using the Oil Production Greenhouse Gas Emissions Estimator (OPGEE). The modeled fields include Cantarell (Mexico), Forties (U.K.), Midway-Sunset (U.S.), Prudhoe Bay (U.S.), and Wilmington (U.S.). Data on field properties and production/processing parameters were obtained from a combination of government and technical literature sources. Key areas of uncertainty include details of the oil and gas surface processing schemes. We aim to explore how long-term trends in depletion at major petroleum fields change the effective energetic productivity of petroleum extraction. Four EROI ratios are estimated for each field as follows: The net energy ratio (NER) and external energy ratio (EER) are calculated, each using two measures of energy outputs, (1) oil-only and (2) all energy outputs. In all cases, engineering estimates of inputs are used rather than expenditure-based estimates (including off-site indirect energy use and embodied energy). All fields display significant declines in NER over the modeling period driven by a combination of (1) reduced petroleum production and (2) increased energy expenditures on recovery methods such as the injection of water, steam, or gas. The fields studied had NER reductions ranging from 46% to 88% over the modeling periods (accounting for all energy outputs). The reasons for declines in EROI differ by field. Midway-Sunset experienced a 5-fold increase in steam injected per barrel of oil produced. In contrast, Prudhoe Bay has experienced nearly a 30-fold increase in amount of gas processed and reinjected per unit of oil produced. In contrast, EER estimates are subject to greater variability and uncertainty due to the relatively small magnitude of external energy investments in most cases.

  15. Estimating decades-long trends in petroleum field energy return on investment (EROI with an engineering-based model.

    Directory of Open Access Journals (Sweden)

    Vinay S Tripathi

    Full Text Available This paper estimates changes in the energy return on investment (EROI for five large petroleum fields over time using the Oil Production Greenhouse Gas Emissions Estimator (OPGEE. The modeled fields include Cantarell (Mexico, Forties (U.K., Midway-Sunset (U.S., Prudhoe Bay (U.S., and Wilmington (U.S.. Data on field properties and production/processing parameters were obtained from a combination of government and technical literature sources. Key areas of uncertainty include details of the oil and gas surface processing schemes. We aim to explore how long-term trends in depletion at major petroleum fields change the effective energetic productivity of petroleum extraction. Four EROI ratios are estimated for each field as follows: The net energy ratio (NER and external energy ratio (EER are calculated, each using two measures of energy outputs, (1 oil-only and (2 all energy outputs. In all cases, engineering estimates of inputs are used rather than expenditure-based estimates (including off-site indirect energy use and embodied energy. All fields display significant declines in NER over the modeling period driven by a combination of (1 reduced petroleum production and (2 increased energy expenditures on recovery methods such as the injection of water, steam, or gas. The fields studied had NER reductions ranging from 46% to 88% over the modeling periods (accounting for all energy outputs. The reasons for declines in EROI differ by field. Midway-Sunset experienced a 5-fold increase in steam injected per barrel of oil produced. In contrast, Prudhoe Bay has experienced nearly a 30-fold increase in amount of gas processed and reinjected per unit of oil produced. In contrast, EER estimates are subject to greater variability and uncertainty due to the relatively small magnitude of external energy investments in most cases.

  16. Origin, distribution, and movement of brine in the Permian Basin (U.S.A.). A model for displacement of connate brine

    International Nuclear Information System (INIS)

    Bein, A.; Dutton, A.R.

    1993-01-01

    Na-Cl, halite Ca-Cl, and gypsum Ca-Cl brines with salinities from 45 to >300 g/L are identified and mapped in four hydrostratigraphic units in the Permian Basin area beneath western Texas and Oklahoma and eastern New Mexico, providing spatial and lithologic constraints on the interpretation of the origin and movement of brine. Na-Cl brine is derived from meteoric water as young as 5-10 Ma that dissolved anhydrite and halite, whereas Ca-Cl brine is interpreted to be ancient, modified-connate Permian brine that now is mixing with, and being displaced by, the Na-Cl brine. Displacement fronts appear as broad mixing zones with no significant salinity gradients. Evolution of Ca-Cl brine composition from ideal evaporated sea water is attributed to dolomitization and syndepositional recycling of halite and bittern salts by intermittent influx of fresh water and sea water. Halite Ca-Cl brine in the evaporite section in the northern part of the basin differs from gypsum Ca-Cl brine in the south-central part in salinity and Na/Cl ratio and reflects segregation between halite- and gypsum-precipitating lagoons during the Permian. Ca-Cl brine moved downward through the evaporite section into the underlying Lower Permian and Pennsylvanian marine section that is now the deep-basin brine aquifer, mixing there with pre-existing sea water. Buoyancy-driven convection of brine dominated local flow for most of basin history, with regional advection governed by topographically related forces dominant only for the past 5 to 10 Ma. 71 refs., 11 figs

  17. Forward Osmosis Brine Drying

    Science.gov (United States)

    Flynn, Michael; Shaw, Hali; Hyde, Deirdre; Beeler, David; Parodi, Jurek

    2015-01-01

    The Forward Osmosis Brine Drying (FOBD) system is based on a technique called forward osmosis (FO). FO is a membrane-based process where the osmotic potential between brine and a salt solution is equalized by the movement of water from the brine to the salt solution. The FOBD system is composed of two main elements, the FO bag and the salt regeneration system. This paper discusses the results of testing of the FO bag to determine the maximum water recovery ratio that can be attained using this technology. Testing demonstrated that the FO bag is capable of achieving a maximum brine water recovery ratio of the brine of 95%. The equivalent system mass was calculated to be 95 kg for a feed similar to the concentrated brine generated on the International Space Station and 86 kg for an Exploration brine. The results have indicated that the FOBD can process all the brine for a one year mission for between 11% to 10% mass required to bring the water needed to make up for water lost in the brine if not recycled. The FOBD saves 685 kg and when treating the International Space Station brine and it saves 829 kg when treating the Exploration brine. It was also demonstrated that saturated salt solutions achieve a higher water recovery ratios than solids salts do and that lithium chloride achieved a higher water recovery ratio than sodium chloride.

  18. Expansion of the Strategic Petroleum Reserve, Alabama, Louisiana, Mississippi, and Texas: Draft Environmental Impact Statement

    International Nuclear Information System (INIS)

    1992-10-01

    The proposed action entails the development of a plan for 250 million barrels of new crude oil storage capacity in two Gulf Coast salt domes to expand the Strategic Petroleum Reserve pursuant to Congressional directive (PL 101--383 and PL 101--512). Storage capacity would be developed by solution-mining the salt which would require about two billion barrels of surface water and would generate about two billion barrels of salt brine. The brine would be disposed of primarily by ocean discharge and alternatively by deep underground injection. Crude oil fill and distribution systems would require new pipelines and terminal facilities. This EIS assesses the impacts of construction and operation for the range of alternatives being considered and focuses on oil and brine spill risk and impacts of brine disposal, water and land use, groundwater contamination, hydrocarbon emissions, and involvement with wetlands and floodplains. This volume contains 20 appendices

  19. Influence of radiolytic products on the chemistry of uranium VI in brines

    International Nuclear Information System (INIS)

    Lucchini, J-F.; Reed, D.T.; Borkowski, M.; Rafalski, A.; Conca, J.

    2004-01-01

    In the near field of a salt repository of nuclear waste, ionizing radiations can strongly affect the chemistry of concentrated saline solutions. Radiolysis can locally modify the redox conditions, speciation, solubility and mobility of the actinide compounds. In the case of uranium VI, radiolytic products can not only reduce U(VI), but also react with uranium species. The net effect on the speciation of uranyl depends on the relative kinetics of the reactions and the buildup of molecular products in brine solutions. The most important molecular products in brines are expected to be hypochlorite ion, hypochlorous acid and hydrogen peroxide. Although U(VI) is expected not to be significantly affected by radiolysis, the combined effects of the major molecular radiolytic products on the chemistry of U(VI) in brines have not been experimentally established previously. (authors)

  20. Facts 2010 - The Norwegian petroleum sector

    Energy Technology Data Exchange (ETDEWEB)

    2010-07-01

    The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Content; Foreword; The petroleum sector - Norway's largest industry; Organisation of Norwegian petroleum activity; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology and industrial development; Environmental considerations in the Norwegian petroleum sector; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

  1. Geochemistry of Salado formation brines recovered from the Waste Isolation Pilot Plant (WIPP) repository

    International Nuclear Information System (INIS)

    Abitz, R.; Myers, J.; Drez, P.; Deal, D.

    1990-01-01

    Intergranular brines recovered from the repository horizon of the Waste Isolation Pilot Plant (WIPP) have major- and trace-element compositions that reflect seawater evaporation and diagenetic processes. Brines obtained from repository drill holes are heterogeneous with respect to composition but their compositional fields are distinct from those obtained from fluid inclusions in WIPP halite. The heterogeneity of brine compositions within the drill-hole population indicates a lack of mixing and fluid homogenization within the salt at the repository level. Compositional differences between intergranular (drill hole) and intragranular (fluid inclusions) brines is attributed to isolation of the latter from diagenetic fluids that were produced from dehydration reactions involving gypsum and clay minerals. Modeling of brine-rock equilibria indicates that equilibration with evaporite minerals controls the concentrations of major elements in the brine. Drill-hole brines are in equilibrium with the observed repository minerals halite, anhydrite, magnesite, polyhalite and quartz. The equilibrium model supports the derivation of drill-hole brines from near-field fluid, rather than large-scale vertical migration of fluids from the overlying Rustler or underlying Castile Formations. 13 refs., 6 figs., 6 tabs

  2. Geochemistry of Salado Formation brines recovered from the Waste Isolation Pilot Plant (WIPP) repository

    International Nuclear Information System (INIS)

    Abitz, R.; Myers, J.; Drez, P.; Deal, D.

    1990-01-01

    Intergranular brines recovered from the repository horizon of the Waste Isolation Pilot Plant (WIPP) have major- and trace-element compositions that reflect seawater evaporation and diagenetic processes. Brines obtained from repository drill holes are heterogenous with respect to composition, but their compositional fields are distinct from those obtained from fluid inclusions in WIPP halite. The heterogeneity of brine compositions within the drill-hole population indicates a lack of mixing and fluid homogenization within the salt at the repository level. Compositional differences between intergranular (drill hole) and intragranular (fluid inclusions) brines is attributed to isolation of the latter from diagenetic fluids that were produced from dehydration reactions involving gypsum and clay minerals. Modeling of brine-rock equilibria indicates that equilibration with evaporite minerals controls the concentrations of major elements in the brine. Drill-hole brines are in equilibrium with the observed repository minerals halite, anhydrite, magnesite, polyhalite and quartz. The equilibrium model supports the derivation of drill-hole brines from near-field fluid, rather than large-scale vertical migration of fluids from the overlying Rustler or underlying Castile Formations. 13 refs., 6 figs., 6 tabs

  3. Modeling brine inflow to Room Q: A numerical investigation of flow mechanisms

    International Nuclear Information System (INIS)

    Freeze, G.A.; Christian-Frear, T.L.; Webb, S.W.

    1997-04-01

    A hydrologic modeling study was performed to gain insight into the flow mechanisms around Room Q. A summary of hydrologic and structural data and of predictive fluid flow models from Room Q are provided. Six years of measured data are available from the time of excavation. No brine accumulation in Room Q was measured in the first two years following excavation. However, there is considerable uncertainty associated with this early-time data due to inadequate sealing of the room. Brine may have been lost to evaporation or it may have flowed into newly created disturbed rock zone (DRZ) porosity resulting from excavation. Non-zero brine accumulation rates were measured from 2--5 years, but brine accumulation within the room dropped to zero after 5.5 years. A conceptual model for brine inflow to Room Q was developed which assumes far-field Darcy flow combined with an increasing DRZ pore volume. Numerical simulations employed TOUGH28W and used predictive DRZ porosity increase with time from SPECTROM-32 rock deformation simulations. Simulated brine inflow showed good agreement with measured brine accumulation rates for the first five years. Two important conclusions were drawn from the simulation results: (1) early-time brine inflow to the room can be reduced to zero if the DRZ pore volume increases with time, and (2) brine accumulation (inflow) rates from 2 to 5 years suggest a far-field permeability of 5 x 10 -22 m 2 with a bulk rock compressibility of 5.4 x 10 -12 Pa -1

  4. Facts 2011 - The Norwegian petroleum sector

    Energy Technology Data Exchange (ETDEWEB)

    2011-07-15

    The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Content; Foreword; The petroleum sector - Norway's largest industry; Organisation of Norwegian petroleum activity; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology and industrial development; Environmental considerations in the Norwegian petroleum sector; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

  5. Facts 2010 - The Norwegian petroleum sector

    Energy Technology Data Exchange (ETDEWEB)

    2010-07-01

    The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Content; Foreword; The petroleum sector - Norway's largest industry; Organisation of Norwegian petroleum activity; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology and industrial development; Environmental considerations in the Norwegian petroleum sector; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

  6. Optimization Models for Petroleum Field Exploitation

    Energy Technology Data Exchange (ETDEWEB)

    Jonsbraaten, Tore Wiig

    1998-12-31

    This thesis presents and discusses various models for optimal development of a petroleum field. The objective of these optimization models is to maximize, under many uncertain parameters, the project`s expected net present value. First, an overview of petroleum field optimization is given from the point of view of operations research. Reservoir equations for a simple reservoir system are derived and discretized and included in optimization models. Linear programming models for optimizing production decisions are discussed and extended to mixed integer programming models where decisions concerning platform, wells and production strategy are optimized. Then, optimal development decisions under uncertain oil prices are discussed. The uncertain oil price is estimated by a finite set of price scenarios with associated probabilities. The problem is one of stochastic mixed integer programming, and the solution approach is to use a scenario and policy aggregation technique developed by Rockafellar and Wets although this technique was developed for continuous variables. Stochastic optimization problems with focus on problems with decision dependent information discoveries are also discussed. A class of ``manageable`` problems is identified and an implicit enumeration algorithm for finding optimal decision policy is proposed. Problems involving uncertain reservoir properties but with a known initial probability distribution over possible reservoir realizations are discussed. Finally, a section on Nash-equilibrium and bargaining in an oil reservoir management game discusses the pool problem arising when two lease owners have access to the same underlying oil reservoir. Because the oil tends to migrate, both lease owners have incentive to drain oil from the competitors part of the reservoir. The discussion is based on a numerical example. 107 refs., 31 figs., 14 tabs.

  7. Soil washing for brine removal

    International Nuclear Information System (INIS)

    Ayyachamy, J.S.; Atalay, A.; Zaman, M.

    1992-01-01

    During the exploration for oil and thereafter, brine transfer lines get ruptured releasing the brine which contaminates the surrounding soil. The salinity level in brine is very high, sometimes approaching or exceeding that of sea water. Soils contaminated with brine are unproductive and unsuitable for plant growth. Several investigators have documented the pollution of surface water and groundwater due to brine disposal from oil and needed to clean up such sites. The objective of this study is to develop a soil washing technique that can be used to remove brine sites were collected and used in the study. This paper reports on results which indicate that soil washing using various surface active agents is effective in removing the brine

  8. Petroleum products. Looking back over the past 50 years

    Energy Technology Data Exchange (ETDEWEB)

    Del Castillo, F. [CONCAWE, Brussels (Belgium)

    2013-04-01

    The field of petroleum products in CONCAWE has historically been concerned with product stewardship and chemicals control legislation relating to the production, marketing and use of petroleum substances. In 1977, the Petroleum Products Management Group issued its first report, titled 'An assessment of precautionary labelling systems relating to the movement of petroleum products in bulk', the objective of which was to promote the harmonisation of labelling for dangerous goods. Over the years CONCAWE has continued to provide guidance to its member companies on compliance with emerging and evolving EU legislation related to the control of chemicals.

  9. Computer-related standards for the petroleum industry

    International Nuclear Information System (INIS)

    Winczewski, L.M.

    1992-01-01

    Rapid application of the computer to all areas of the petroleum industry is straining the capabilities of corporations and vendors to efficiently integrate computer tools into the work environment. Barriers to this integration arose form decades of competitive development of proprietary applications formats, along with compilation of data bases in isolation. Rapidly emerging industry-wide standards relating to computer applications and data management are poised to topple these barriers. This paper identifies the most active players within a rapidly evolving group of cooperative standardization activities sponsored by the petroleum industry. Summarized are their objectives, achievements, current activities and relationships to each other. The trends of these activities are assessed and projected

  10. An experimental study of relative permeability hysteresis, capillary trapping characteristics, and capillary pressure of CO2/brine systems at reservoir conditions

    Science.gov (United States)

    Akbarabadi, Morteza

    We present the results of an extensive experimental study on the effects of hysteresis on permanent capillary trapping and relative permeability of CO2/brine and supercritical (sc)CO2+SO2/brine systems. We performed numerous unsteady- and steady-state drainage and imbibition full-recirculation flow experiments in three different sandstone rock samples, i.e., low and high-permeability Berea, Nugget sandstones, and Madison limestone carbonate rock sample. A state-of-the-art reservoir conditions core-flooding system was used to perform the tests. The core-flooding apparatus included a medical CT scanner to measure in-situ saturations. The scanner was rotated to the horizontal orientation allowing flow tests through vertically-placed core samples with about 3.8 cm diameter and 15 cm length. Both scCO2 /brine and gaseous CO2 (gCO2)/brine fluid systems were studied. The gaseous and supercritical CO2/brine experiments were carried out at 3.46 and 11 MPa back pressures and 20 and 55°C temperatures, respectively. Under the above-mentioned conditions, the gCO2 and scCO2 have 0.081 and 0.393 gr/cm3 densities, respectively. During unsteady-state tests, the samples were first saturated with brine and then flooded with CO2 (drainage) at different maximum flow rates. The drainage process was then followed by a low flow rate (0.375 cm 3/min) imbibition until residual CO2 saturation was achieved. Wide flow rate ranges of 0.25 to 20 cm3/min for scCO2 and 0.125 to 120 cm3min for gCO2 were used to investigate the variation of initial brine saturation (Swi) with maximum CO2 flow rate and variation of trapped CO2 saturation (SCO2r) with Swi. For a given Swi, the trapped scCO2 saturation was less than that of gCO2 in the same sample. This was attributed to brine being less wetting in the presence of scCO2 than in the presence of gCO 2. During the steady-state experiments, after providing of fully-brine saturated core, scCO2 was injected along with brine to find the drainage curve and as

  11. Environmental issues of petroleum exploration and production: Introduction

    Science.gov (United States)

    Kharaka, Yousif K.; Dorsey, Nancy S.

    2005-01-01

    Energy is the lifeblood of our planet Earth, an essential commod- ity that powers the expanding global economy. Starting in the 1950s, oil and natural gas became the main sources of primary energy for the increasing world population, and this dominance is expected to continue for several more decades (Edwards, 1997; Energy Information Administration (EIA), 2004). In the United States, petroleum production started in 1859 when Drake's well was drilled near Titusville, Pennsylvania, and oil and natural gas currently supply approximately 63% of the energy consumption; forecasts indicate that by 2025, their use will increase by about 40% to 28.3 million bbl/day and to 31.4 tcf/yr (EIA, 2004). The clear benefits of petroleum consumption, however, can carry major environmental impacts that may be regional or global in scale, in- cluding air pollution, global climate change, and oil spills. This vol- ume of Environmental Geosciences, covering environmental impacts of petroleum exploration and production, does not address these major impacts directly because air pollution and global warming are issues related primarily to petroleum and coal uses, and major oil spills are generally attributed to marine petroleum transportation, such as the Exxon Valdez's 1989 spill of 260,000 bbl of oil into Prince William Sound, Alaska. Exploration for and production of petroleum, however, have caused local detrimental impacts to soils, surface and groundwa- ters, and ecosystems in the 36 producing states in the United States (Richter and Kreitler, 1993; Kharaka and Hanor, 2003). These im- pacts arose primarily from the improper disposal of some of the large volumes (presently estimated at 20 billion bbl/yr total pro- duced) of saline water produced with oil and gas, from accidental hydrocarbon and produced-water releases, and from abandoned oil wells that were orphaned or not correctly plugged (Kharaka et al., 1995; Veil et al., 2004). Impacts and ground-surface disturbances, in the order

  12. Brine flow in heated geologic salt.

    Energy Technology Data Exchange (ETDEWEB)

    Kuhlman, Kristopher L.; Malama, Bwalya

    2013-03-01

    This report is a summary of the physical processes, primary governing equations, solution approaches, and historic testing related to brine migration in geologic salt. Although most information presented in this report is not new, we synthesize a large amount of material scattered across dozens of laboratory reports, journal papers, conference proceedings, and textbooks. We present a mathematical description of the governing brine flow mechanisms in geologic salt. We outline the general coupled thermal, multi-phase hydrologic, and mechanical processes. We derive these processes governing equations, which can be used to predict brine flow. These equations are valid under a wide variety of conditions applicable to radioactive waste disposal in rooms and boreholes excavated into geologic salt.

  13. Facts 2009 - The Norwegian petroleum sector

    Energy Technology Data Exchange (ETDEWEB)

    2009-07-01

    The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Contents: Foreword; The petroleum sector; Norwegian resource management; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology; Environmental considerations; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

  14. Petroleum 1996 - issues and trends

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-01

    Increasingly, users of the Energy Information Administration`s petroleum data and analytical reports have expressed an interest in a recurring report that takes a broad view of the petroleum sector. What is sought is some perspective on the complex interrelationships that comprise an industry and markets accounting for 40 percent of the energy consumed in the United States and ranging from the drilling rig in the oil field to the pump at the local gasoline station. This report comprehensively examines historical trends, and selectively focuses on major issues and the events they represent. It analyzes different dimensions of the industry and related markets in terms of how they relate to a common theme, in this case, the volatility in petroleum markets.

  15. Expected brine movement at potential nuclear waste repository salt sites

    International Nuclear Information System (INIS)

    McCauley, V.S.; Raines, G.E.

    1987-08-01

    The BRINEMIG brine migration code predicts rates and quantities of brine migration to a waste package emplaced in a high-level nuclear waste repository in salt. The BRINEMIG code is an explicit time-marching finite-difference code that solves a mass balance equation and uses the Jenks equation to predict velocities of brine migration. Predictions were made for the seven potentially acceptable salt sites under consideration as locations for the first US high-level nuclear waste repository. Predicted total quantities of accumulated brine were on the order of 1 m 3 brine per waste package or less. Less brine accumulation is expected at domal salt sites because of the lower initial moisture contents relative to bedded salt sites. Less total accumulation of brine is predicted for spent fuel than for commercial high-level waste because of the lower temperatures generated by spent fuel. 11 refs., 36 figs., 29 tabs

  16. Petroleum related business activities in Hordaland - competence, flexibility and future possibilities

    International Nuclear Information System (INIS)

    Osland, Ove

    2004-06-01

    The aim of the study has been to determine the future conditions of the supply business in Hordaland for petroleum related activities, international competition and on markets outside the Norwegian shelf. In addition it is focused on the adjustment possibilities of the companies during the expected decrease of activity on the Norwegian continental shelf. The report is based on a questionnaire to the company leadership. In 2003 there was 15073 persons employed in the petroleum activities in Hordaland. Out of this the supplier activities account for 10500 employees which is 4.7 % of the total employment in the county. Service deliveries to the shelf are included in the figure. The productivity related competence in these companies is substantial. The work force has a high educational level where more than half has an education of college or higher. Most of the firms have been in the industry for a long time. A substantial part of the suppliers in Hordaland is internationally competitive and participates globally. The companies are to a varying degree specialized for petroleum activities but most of them get their income largely from the petroleum market. A substantial number of companies inform that they would participate in the foreign petroleum market when decrease of activities on the Norwegian shelf occurs. The majority of the companies have however, the capability to adjust to other markets than petroleum exploitation

  17. Use of a multi-process phytoremediation system for decontamination of petroleum impacted soils : results of successful field trials

    International Nuclear Information System (INIS)

    Greenberg, B.M.; Gurska, J.; Huang, X.D.; Gerhardt, K.E.; Yu, X.M.; Nykamp, J.; MacNeill, G.; Yang, S.; Lu, X.; Glick, B.; Wang, W.; Knezevich, N.; Reid, N.

    2008-01-01

    The multi-process phytoremediation system (MPPS) was developed to degrade petroleum hydrocarbons (PHCs) in impacted soils. Phytoremediation of persistent contaminants in soils holds significant promise for rapid remediation kinetics. MPPS effectively removes polycyclic aromatic hydrocarbons (PAHs), total petroleum hydrocarbons (TPHs) and chlorinated hydrocarbons (CHCs) from soils. A plant growth promoting rhizobacteria interaction is the main element for success as it mitigates stress ethylene effects in plants, leading to high root biomass which, in turn, promotes growth of rhizosphere organisms. Field tests of the MPPS were initiated at a farm site in Sarnia, Ontario in the summer of 2004. The field was contaminated with petroleum hydrocarbons from refinery oil sludge. The second field trial was performed for 3 consecutive years at a petroleum contaminated biopile in Turner Valley, Alberta. The paper presented the results of the successful field tests of the MPPS. It was concluded that increased root biomass is achieved in the contaminated soils, which leads to more efficient and complete removal of TPHs in the field. Three years of field trials of the MPPS showed that remediation continues with successive seasons. 28 refs., 1 tab., 3 figs

  18. Mass transfer of H2O between petroleum and water: implications for oil field water sample quality

    International Nuclear Information System (INIS)

    McCartney, R.A.; Ostvold, T.

    2005-01-01

    Water mass transfer can occur between water and petroleum during changes in pressure and temperature. This process can result in the dilution or concentration of dissolved ions in the water phase of oil field petroleum-water samples. In this study, PVT simulations were undertaken for 4 petroleum-water systems covering a range of reservoir conditions (80-185 o C; 300-1000 bar) and a range of water-petroleum mixtures (volume ratios of 1:1000-300:1000) to quantify the extent of H 2 O mass transfer as a result of pressure and temperature changes. Conditions were selected to be relevant to different types of oil field water sample (i.e. surface, downhole and core samples). The main variables determining the extent of dilution and concentration were found to be: (a) reservoir pressure and temperature, (b) pressure and temperature of separation of water and petroleum, (c) petroleum composition, and (d) petroleum:water ratio (PWR). The results showed that significant dilution and concentration of water samples could occur, particularly at high PWR. It was not possible to establish simple guidelines for identifying good and poor quality samples due to the interplay of the above variables. Sample quality is best investigated using PVT software of the type used in this study. (author)

  19. Petroleum field management, evolution and perspectives; Gerenciamento de campo de petroleo, evolucao e perspectivas

    Energy Technology Data Exchange (ETDEWEB)

    Castro, Guilherme Teixeira de

    1999-07-01

    In Brazil until few years ago the petroleum exploration and production were state's monopoly, with the opening of the market became necessary implements some changes, to create conditions to the national industry can survive in this new scenery. The objective of this work is to propose a model for petroleum fields management based on the examples with more success mentioned in the literature. (author)

  20. Petroleum field management, evolution and perspectives; Gerenciamento de campo de petroleo, evolucao e perspectivas

    Energy Technology Data Exchange (ETDEWEB)

    Castro, Guilherme Teixeira de

    1999-07-01

    In Brazil until few years ago the petroleum exploration and production were state's monopoly, with the opening of the market became necessary implements some changes, to create conditions to the national industry can survive in this new scenery. The objective of this work is to propose a model for petroleum fields management based on the examples with more success mentioned in the literature. (author)

  1. Expansion of the Strategic Petroleum Reserve, Alabama, Louisiana, Mississippi, and Texas: Draft environmental impact statement

    International Nuclear Information System (INIS)

    1992-10-01

    The proposed action entails the development of a plan for 250 million barrels of new crude oil storage capacity in two Gulf Coast salt domes to expand the Strategic Petroleum Reserve pursuant to Congressional directive (PL 101--383 and PL 101--512). Storage capacity would be developed by solution-mining the salt which would require about two billion barrels of surface water and would generate about two billion barrels of salt brine. The brine would be disposed of primarily by ocean discharge and alternatively by deep underground injection. Crude oil fill and distribution systems would require new pipelines and terminal facilities. This EIS assesses the impacts of construction and operation for the range of alternatives being considered and focuses on oil and brine spill risk and impacts of brine disposal, water and land use, groundwater contamination, hydrocarbon emissions, and involvement with wetlands and floodplains. This volume focuses on the environmental risks and public occupational health and safety, environmental impacts, regulatory requirements and mitigation methods, the relationship between local short-term use and long-term productivity, and the commitment of resources

  2. Petroleum Vapor - Field Technical

    Science.gov (United States)

    The screening approach being developed by EPA OUST to evaluate petroleum vapor intrusion (PVI) requires information that has not be routinely collected in the past at vapor intrusion sites. What is the best way to collect this data? What are the relevant data quality issues and ...

  3. Brine migration in salt and its implications in the geologic disposal of nuclear waste

    International Nuclear Information System (INIS)

    Jenks, G.H.; Claiborne, H.C.

    1981-12-01

    This report respresents a comprehensive review and analysis of available information relating to brine migration in salt surrounding radioactive waste in a salt repository. The topics covered relate to (1) the characteristics of salt formations and waste packages pertinent to considerations of rates, amounts, and effects of brine migration, (2) experimental and theoretical information on brine migration, and (3) means of designing to minimize any adverse effects of brine migration. Flooding, brine pockets, and other topics were not considered, since these features will presumably be eliminated by appropriate site selection and repository design. 115 references

  4. Field desorption mass spectroscopy monitoring of changes in hydrocarbon type composition during petroleum biodegradation

    International Nuclear Information System (INIS)

    Huesemann, M.H.

    1995-01-01

    A comprehensive petroleum hydrocarbon characterization procedure involving group type separation, boiling point distribution, and hydrocarbon typing by field desorption mass spectroscopy (FDMS) has been developed to quantify changes in hydrocarbon type composition during bioremediation of petroleum-contaminated soils. FDMS is able to quantify the concentration of hundreds of specific hydrocarbon types based on their respective hydrogen deficiency (z-number) and molecular weight (carbon number). Analytical results from two bioremediation experiments involving soil contaminated with crude oil and motor oil indicate that alkanes and two-ring saturates (naphthenes) were readily biodegradable. In addition, low-molecular-weight hydrocarbons generally were biodegraded to a larger extent than those of high molecular weight. More importantly, it was found that the extent of biodegradation of specific hydrocarbon types was comparable between treatments and appeared to be unaffected by the petroleum contaminant source, soil type, or experimental conditions. It was therefore concluded that in these studies the extent of total petroleum hydrocarbon (TPH) biodegradation is primarily affected by the molecular composition of the petroleum hydrocarbons present in the contaminated soil

  5. Geochemistry and petrology of surface samples, six boreholes and brines from the Salton Sea geothermal field: A natural analog of a nuclear waste repository in salt: Report No. 3

    International Nuclear Information System (INIS)

    1987-05-01

    Cuttings from six wells in the Salton Sea geothermal field, and rocks at outcrop that are correlative in age with those encountered at depth in the wells were analyzed in detail. Mineralogy, petrography, x-ray diffraction, electron microprobe, instrumental neutron activation analysis, fission track radiography, oxygen and stable carbon isotopic, uranium-thorium series disequilibrium, and fluid inclusion analyses are reported. Where fluids were being produced from wells, brine chemistry as well as stable isotope and uranium-thorium series analyses are reported. Particular attention has been paid to defining zones of fluid-rock interaction in which analyses of coexisting geothermal reservoir brine and hydrothermally altered sediments could be acquired. A wide span of temperatures, from surficial to greater than 300/degree/C, and salinities ranging from relatively dilute ground waters up to brines of 25 wt% total dissolved solids, span a range of environments that might be encountered in a waste repository in salt. Progressive hydrothermal alteration, mineral formation and element mobility are documented in the data presented. 52 refs., 25 figs., 49 tabs

  6. Brine Sampling and Evaluation Program

    International Nuclear Information System (INIS)

    Deal, D.E.; Case, J.B.; Deshler, R.M.; Drez, P.E.; Myers, J.; Tyburski, J.R.

    1987-12-01

    The Brine Sampling and Evaluation Program (BSEP) Phase II Report is an interim report which updates the data released in the BSEP Phase I Report. Direct measurements and observations of the brine that seeps into the WIPP repository excavations were continued through the period between August 1986 and July 1987. That data is included in Appendix A, which extends the observation period for some locations to approximately 900 days. Brine observations at 87 locations are presented in this report. Although WIPP underground workings are considered ''dry,'' small amounts of brine are present. Part of that brine migrates into the repository in response to pressure gradients at essentially isothermal conditions. The data presented in this report is a continuation of moisture content studies of the WIPP facility horizon that were initiated in 1982, as soon as underground drifts began to be excavated. Brine seepages are manifested by salt efflorescences, moist areas, and fluid accumulations in drillholes. 35 refs., 6 figs., 11 tabs

  7. PILOT TESTING: PRETREATMENT OPTIONS TO ALLOW RE-USE OF FRAC FLOWBACK AND PRODUCED BRINE FOR GAS SHALE RESOURCE DEVELOPMENT

    Energy Technology Data Exchange (ETDEWEB)

    Burnett, David

    2012-12-31

    The goal of the A&M DOE NETL Project No. DE-FE0000847 was to develop a mobile, multifunctional water treatment capability designed specifically for “pre-treatment” of field waste brine. The project consisted of constructing s mobile “field laboratory” incorporating new technology for treating high salinity produced water and using the lab to conduct a side-by-side comparison between this new technology and that already existing in field operations. A series of four field trials were performed utilizing the mobile unit to demonstrate the effectiveness of different technology suitable for use with high salinity flow back brines and produced water. The design of the mobile unit was based on previous and current work at the Texas A&M Separation Sciences Pilot Plant. The several treatment techniques which have been found to be successful in both pilot plant and field tests had been tested to incorporate into a single multifunctional process train. Eight different components were evaluated during the trials, two types of oil and grease removal, one BTEX removal step, three micro-filters, and two different nanofilters. The performance of each technique was measured by its separation efficiency, power consumption, and ability to withstand fouling. The field trials were a success. Four different field brines were evaluated in the first trial in New York. Over 16,000 gallons of brine were processed. Using a power cost of $.10 per kWh, media pretreatment power use averaged $0.004 per barrel, solids removal $.04 per barrel and brine “softening” $.84 per barrel. Total power cost was approximately $1.00 per barrel of fluid treated. In Pennsylvania, brines collected from frac ponds were tested in two additional trials. Each of the brines was converted to an oil-free, solids-free brine with no biological activity. Brines were stable over time and would be good candidates for use as a make-up fluid in a subsequent fracturing fluid design. Reports on all of the field

  8. The impact of radioactivity of brine water on environment on the territory of the Caspian sea

    International Nuclear Information System (INIS)

    Mamedov, F.I.; Gurbanova, E.K.

    2015-01-01

    At the present, the problem of purification of the petroleum polluted areas is getting essential. The reason of that is the increased scope of work on oil producing and oil refining. Consequently, the risk of contamination of the environment increases. So far, experts have considered that hydrocarbons which are contained in composition of oil waste are most dangerous for environment. In the last decade were discovered tens of different metals, halogens and radioactive elements in the oil, the gas and the brine water.

  9. Brine Sampling and Evaluation Program, 1990 report

    Energy Technology Data Exchange (ETDEWEB)

    Deal, D.E.; Abitz, R.J.; Myers, J.; Case, J.B.; Martin, M.L.; Roggenthen, W.M. [International Technology Corp., Albuquerque, NM (United States); Belski, D.S. [Westinghouse Electric Corp., Carlsbad, NM (United States). Waste Isolation Div.

    1991-08-01

    The data presented in this report are the result of Brine Sampling and Evaluation Program (BSEP) activities at the Waste Isolation Pilot Plant (WIPP) during 1990. When excavations began in 1982, small brine seepages (weeps) were observed on the walls. These brine occurrences were initially described as part of the Site Validation Program. Brine studies were formalized in 1985. The BSEP activities document and investigate the origins, hydraulic characteristics, extent, and composition of brine occurrences in the Permian Salado Formation and seepage of that brine into the excavations at the WIPP. The brine chemistry is important because it assists in understanding the origin of the brine and because it may affect possible chemical reactions in the buried waste after sealing the repository. The volume of brine and the hydrologic system that drives the brine seepage also need to be understood to assess the long-term performance of the repository. After more than eight years of observations (1982--1990), no credible evidence exists to indicate that enough naturally occurring brine will seep into the WIPP excavations to be of practical concern. The detailed observations and analyses summarized herein and in previous BSEP reports confirm the evidence apparent during casual visits to the underground workings -- that the excavations are remarkably dry.

  10. Brine Sampling and Evaluation Program, 1990 report

    International Nuclear Information System (INIS)

    Deal, D.E.; Abitz, R.J.; Myers, J.; Case, J.B.; Martin, M.L.; Roggenthen, W.M.; Belski, D.S.

    1991-08-01

    The data presented in this report are the result of Brine Sampling and Evaluation Program (BSEP) activities at the Waste Isolation Pilot Plant (WIPP) during 1990. When excavations began in 1982, small brine seepages (weeps) were observed on the walls. These brine occurrences were initially described as part of the Site Validation Program. Brine studies were formalized in 1985. The BSEP activities document and investigate the origins, hydraulic characteristics, extent, and composition of brine occurrences in the Permian Salado Formation and seepage of that brine into the excavations at the WIPP. The brine chemistry is important because it assists in understanding the origin of the brine and because it may affect possible chemical reactions in the buried waste after sealing the repository. The volume of brine and the hydrologic system that drives the brine seepage also need to be understood to assess the long-term performance of the repository. After more than eight years of observations (1982--1990), no credible evidence exists to indicate that enough naturally occurring brine will seep into the WIPP excavations to be of practical concern. The detailed observations and analyses summarized herein and in previous BSEP reports confirm the evidence apparent during casual visits to the underground workings -- that the excavations are remarkably dry

  11. Performance evaluation of a once-through multi-stage flash distillation system: Impact of brine heater fouling

    International Nuclear Information System (INIS)

    Baig, Hasan; Antar, Mohamed A.; Zubair, Syed M.

    2011-01-01

    Multi-stage flash distillation (MSF) system modeling involves a number of process variables. An estimation of all these process variables requires both analytical solutions and experimental/field analysis. However, the accurate estimate of variables related to the brine heater operation in a MSF system is very important for a reliable operation of the system. For example, steam operating conditions as well as the brine properties including fouling of the brine heater tubes have a significant effect on the heat transfer characteristics of the brine heater, which in turn influence the distillate output from the system. In this study, the effect of various design as well as operating conditions on the performance ratio (PR), brine temperature and salinity as it leaves the last flash stage are investigated in a once-through system. Increasing the number of stages from 24 to 32 has a significant effect on the PR, it ranges between 79% (for ΔT = 1.5) and 327% (for ΔT = 2.3) for a top-brine temperature of 106 o C. This value increase as the top-brine temperature increases. Increasing the stage-to-stage temperature difference increases the water salinity as it leaves the final stage and reduces its temperature that would imply better energy utilization within the plant. Results show that brine side heat exchanger fouling has a significant effect in decreasing the overall heat transfer coefficient, which reduces the production rate as the fouling increases with time. A sensitivity analysis to identify the key parameters, which can have a significant influence on the desalination plant performance, is carried out in an attempt to contribute a better understanding and operation of MSF desalination processes.

  12. Petroleum Characterisation and Reservoir Dynamics - The Froey Field and the Rind Discovery, Norwegian Continental Shelf

    Energy Technology Data Exchange (ETDEWEB)

    Bhullar, Abid G.

    1999-07-01

    The objective of this thesis is to apply the fundamental principles of petroleum geochemistry integrated with petroleum/reservoir engineering and geological concepts to the dynamics and characterisation of petroleum reservoirs. The study is based on 600 core samples and 9 DST oils from 11 wells in the Froey Field and the Rind Discovery. The work is presented in five papers. Paper 1 is a detailed characterisation of the reservoirs using a petroleum geochemical approach. Paper 2 describes the application of a single reservoir geochemical screening technique to exploration, appraisal and production geology and reservoir/petroleum engineering. Paper 3 compares the Iatroscan TLC-FID screening technique and the extraction efficiency of micro-extraction used in this work with the well-established Rock-Eval geochemical screening method and with the Soxtec extraction method. Paper 4 refines the migration and filling models of Paper 1, and Paper 5 presents a comparison of models of petroleum generation, migration and accumulation based on geochemical data with 1D burial history, a ''pseudo well'' based on actual well data and regional seismic analysis representing the hydrocarbon generative basin conditions.

  13. Brine Sampling and Evaluation Program: 1988 report

    International Nuclear Information System (INIS)

    Deal, D.E.; Abitz, R.J.; Case, J.B.; Crawley, M.E.; Deshler, R.M.; Drez, P.E.; Givens, C.A.; King, R.B.; Myers, J.; Pietz, J.M.; Roggenthen, W.M.; Tyburski, J.R.; Belski, D.S.; Niou, S.; Wallace, M.G.

    1989-12-01

    The data presented in this report are the result of Brine Sampling and Evaluation Program (BSEP) activities at the Waste Isolation Pilot Plant (WIPP) during 1988. These activities, which are a continuation and update of studies that began in 1982 as part of the Site Validation Program, were formalized as the BSEP in 1985 to document and investigate the origins, hydraulic characteristics, extent, and composition of brine occurrences in the Permian Salado Formation, and seepage of that brine into the excavations at the WIPP. Previous BSEP reports (Deal and Case, 1987; Deal and others, 1987) described the results of ongoing activities that monitor brine inflow into boreholes in the facility, moisture content of the Salado Formation, brine geochemistry, and brine weeps and crusts. The information provided in this report updates past work and describes progress made during the calendar year 1988. During 1988, BSEP activities focused on four major areas to describe and quantify brine activity: (1) monitoring of brine inflow parameters, e.g., measuring brines recovered from holes drilled upward from the underground drifts (upholes), downward from the underground drifts (downholes), and near-horizontal holes; (2) characterizing the brine, e.g., the geochemistry of the brine and the presence of bacteria and their possible interactions with experiments and operations; (3) characterizing formation properties associated with the occurrence of brine; e.g., determining the water content of various geologic units, examining these units in boreholes using a video camera system, and measuring their resistivity (conductivity); and (4) modeling to examine the interaction of salt deformation near the workings and brine seepage through the deforming salt. 77 refs., 48 figs., 32 tabs

  14. Analysis of petroleum oily sludge producing in petroleum field of Rio Grande do Norte, Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Lima, Cicero de Souza; Lima, Regineide Oliveira; Silva, Edjane Fabiula Buriti da; Castro, Kesia Kelly Vieira de; Chiavone Filho, Osvaldo; Araujo, Antonio Souza de [Universidade Federal do Rio Grande do Norte (UFRN), RN (Brazil)

    2012-07-01

    In exploration and production of petroleum is generated solid waste different and components other. The petroleum oily sludge is a complex mix of components different (water, oil and solid). The petroleum oily sludge generally has other residues and is formed during production and operations, transport, storage and petroleum refining (atmospheric residue, vacuum residue and catalytic cracking residue). However, according to its origin, the compositions can be found quite varied for sludge. Observing the process steps production and refining is possible to locate its main sources and percentage contributions in terms of waste generation. The elemental analysis was performed with oily sludge from region and it showed different composition. For carbon element and hydrogen, small differences was observed, but for was observed greater differences for Oxygen element. The sludge has different inorganic and organic composition. The sludge from oil water separator (OWS) 2 showed a greater amount of oil (94.88%), this may indicate a residue of aggregate high for petroleum industry. In analysis of Saturates, Aromatics, Resins and Asphaltenes (SARA), the sludge from unloading showed amount high of saturates. The inorganic material separated from sludge was characterized and sludge from OWS 2 had high amount sulfur (41.57%). The sludge analyzed showed organic components high values, so it can be treated and reprocessed in process units petroleum industry. The analysis thermal degradation had a better setting for treated oily sludge. (author)

  15. Deep brine recognition upstream the EBE syndicate. Geochemical and isotopic investigations. Final report

    International Nuclear Information System (INIS)

    2009-01-01

    The authors report and discuss the results obtained after performing a drilling upstream the drinkable water harnessing field of a water supply syndicate in Alsace (Ensisheim, Bollwiller and surroundings), in order to confirm the existence of a deep brine source. This brine is diluted by recent waters. The first isotopic investigations do not allow the origin of this brine to be identified, but fractures due to some seismic events are suspected. The report presents the drilling and the various aspects of the chemical and isotopic studies (sampling, physico-chemical analysis, dating, identification of various isotopes)

  16. Brine Sampling and Evaluation Program, 1991 report

    Energy Technology Data Exchange (ETDEWEB)

    Deal, D.E.; Abitz, R.J.; Myers, J.; Martin, M.L.; Milligan, D.J.; Sobocinski, R.W.; Lipponer, P.P.J. [International Technology Corp., Albuquerque, NM (United States); Belski, D.S. [Westinghouse Electric Corp., Carlsbad, NM (United States). Waste Isolation Div.

    1993-09-01

    The data presented in this report are the result of Brine Sampling and Evaluation Program (BSEP) activities at the Waste Isolation Pilot Plan (WIPP) during 1991. These BSEP activities document and investigate the origins, hydraulic characteristics, extent, and composition of brine occurrences in the Permian Salado Formation and seepage of that brine into the excavations at the WIPP. When excavations began at the WIPP in 1982, small brine seepages (weeps) were observed on the walls. Brine studies began as part of the Site Validation Program and were formalized as a program in its own right in 1985. During nine years of observations (1982--1991), evidence has mounted that the amount of brine seeping into the WIPP excavations is limited, local, and only a small fraction of that required to produce hydrogen gas by corroding the metal in the waste drums and waste inventory. The data through 1990 is discussed in detail and summarized by Deal and others (1991). The data presented in this report describes progress made during the calendar year 1991 and focuses on four major areas: (1) quantification of the amount of brine seeping across vertical surfaces in the WIPP excavations (brine ``weeps); (2) monitoring of brine inflow, e.g., measuring brines recovered from holes drilled downward from the underground drifts (downholes), upward from the underground drifts (upholes), and from subhorizontal holes; (3) further characterization of brine geochemistry; and (4) preliminary quantification of the amount of brine that might be released by squeezing the underconsolidated clays present in the Salado Formation.

  17. Fact sheet. Norwegian petroleum activity 1996

    Energy Technology Data Exchange (ETDEWEB)

    Westgaard, T. [ed.

    1996-02-01

    The present report from the Royal Ministry of Industry and Energy deals with the Norwegian petroleum activity. Main topics are as follow: Historical overview; state organisation of petroleum activities; the economic impact of Norwegian oil and gas; state revenues; mainland activities; petroleum resources; production; marketing situation for petroleum products; environmental aspects; the legal and licence framework; licensing rounds; exploration; fields in production; fields under development; discoveries with development plan under consideration; transportation systems; licence interests; company interests. 36 refs., 24 figs., 15 tabs.

  18. Petroleum and natural gas economy in Arab Countries, in Congo, Ethiopia, Gabon and Iran

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    This paper gives informations on petroleum and natural gas industry, petroleum market and prices, trade and contracts, prospection and investments: Portugal has retained the candidature of ten foreign companies for the introduction of natural gas in 1996 and the first enhanced recovery contract will relate to Rhourde El Baguel natural gas field (Algeria). New contracts have been signed for exploration or development of petroleum or natural gas fields in Gabon, Ethiopia and Libya. Iraq has restarted its petroleum exports and Iranian production has diminished

  19. Characterization of contamination, source and degradation of petroleum between upland and paddy fields based on geochemical characteristics and phospholipid fatty acids.

    Science.gov (United States)

    Zhang, Juan; Wang, Renqing; Du, Xiaoming; Li, Fasheng; Dai, Jiulan

    2012-01-01

    To evaluate contamination caused by petroleum, surface soil samples were collected from both upland and paddy fields along the irrigation canals in the Hunpu wastewater irrigation region in northeast China. N-alkanes, terpanes, steranes, and phospholipid fatty acids (PLFA) in the surface soil samples were analyzed. The aliphatic hydrocarbon concentration was highest in the samples obtained from the upland field near an operational oil well; it was lowest at I-3P where wastewater irrigation promoted the downward movement of hydrocarbons. The Hunpu region was found contaminated by heavy petroleum from oxic lacustrine fresh water or marine deltaic source rocks. Geochemical parameters also indicated significantly heavier contamination and degradation in the upland fields compared with the paddy fields. Principal component analysis based on PLFA showed various microbial communities between petroleum contaminated upland and paddy fields. Gram-negative bacteria indicated by 15:0, 3OH 12:0, and 16:1(9) were significantly higher in the paddy fields, whereas Gram-positive bacteria indicated by i16:0 and 18:1(9)c were significantly higher in the upland fields (p petroleum contamination. Poly-unsaturated PLFA (18:2omega6, 9; indicative of hydrocarbon-degrading bacteria and fungi) was also significantly elevated in the upland fields. This paper recommends more sensitive indicators of contamination and degradation of petroleum in soil. The results also provide guidelines on soil pollution control and remediation in the Hunpu region and other similar regions.

  20. International petroleum enviromental conference (IPEC) offers opportunity for exchange of ideas

    International Nuclear Information System (INIS)

    Veil, J.A.; Spiric, Z.

    2001-01-01

    Oil and gas are produced in many parts of the world. Persons working in the petroleum industry can learn much by communicating with colleagues in other countries, but the opportunities for engineers and scientists to come together and discuss petroleum environmental control practices, technologies, and regulations with representatives of other countries are limited. This paper describes the very useful International Petroleum Environmental Conference (IPEC) which completed its seventh meeting in November 2000 in Albuquerque, New Mexico, USA. The 7th IPEC attracted 350 participants, including 26 participants from countries other than the United States. The 7th IPEC emphasized international issues and included more than 20 papers by international authors or on international topics. The conference covered all aspects of petroleum environmental issues and featured speakers from many disciplines. The conference included technical sessions on the following topics: Legal and Regulatory Issues in the Oil and Gas Industry; Pollution Prevention, Waste Management, and Waste Minimization; Bioremediation of Petroleum Hydrocarbons; Characterization and Remediation of Brine-Impacted Soils; Biotreatment and Bioremediation; International Issues in the Oil and Gas Industry; Phytoremediation of Petroleum Hydrocarbons; Treatment and Management of Produced Water; Forensic Geochemistry and Site Characterization/Technology Transfer; Environmentall Acceptable Endpoints; Desulfurization of Fuels and Waste Streams; Control of Air Emissions; MTBE/Phytoremediation and Natural Attenuation; and Treatment and Remediation of Petroleum Hydrocarbons. The last day of the conference was devoted to a special symposium on 'Innovative Technologies for Subsurface Characterization and Remediation.' The authors recommend this conference as a forum for industry, government, and academia to freely exchange ideas and information

  1. Searching for brine on Mars using Raman spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, E.

    2016-07-01

    In the last few years, water ice and perchlorate salts capable of melting this ice and producing liquid solutions have been discovered at the surface and shallow subsurface of Mars. In addition to via melting of ice, perchlorate salts may also form liquid solutions by absorbing water vapor when the relative humidity is above a certain threshold in a process known as deliquescence. Formed either by melting or deliquescence, liquid solutions (brine) are the most likely way of liquid water activity on the Martian surface and in the shallow subsurface and are therefore important to understand the habitability of Mars. Using Raman spectroscopy, we provide reference spectra of various mixing states of liquid water, water ice and calcium perchlorate, all of which can occur during brine formation. We focus on the perchlorate symmetric stretching band and the O-H stretching vibrational band to distinguish brine from crystalline salt and water ice. We show that perchlorate brines can be identified by analyzing the peaks and their widths in the decomposed Raman spectra of the investigated samples. This serves as an important reference for future in-situ Raman spectrometers on Mars, such as those on the ExoMars and Mars 2020 rovers and can aid in the detection of brine formation on Mars. (Author)

  2. Facts 2011 - The Norwegian petroleum sector; Fakta 2011 - norsk petroleumsverksemd

    Energy Technology Data Exchange (ETDEWEB)

    2011-07-15

    The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Content; Foreword; The petroleum sector - Norway's largest industry; Organisation of Norwegian petroleum activity; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology and industrial development; Environmental considerations in the Norwegian petroleum sector; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

  3. Facts 2010 - The Norwegian petroleum sector; Fakta 2010 - norsk petroleumsverksemd

    Energy Technology Data Exchange (ETDEWEB)

    2010-07-01

    The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Content; Foreword; The petroleum sector - Norway's largest industry; Organisation of Norwegian petroleum activity; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology and industrial development; Environmental considerations in the Norwegian petroleum sector; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

  4. Possible Mars brines - Equilibrium and kinetic considerations

    Science.gov (United States)

    Zent, A. P.; Fanale, F. P.

    1986-01-01

    To determine the fate of postulated near surface brines on Mars, the rate of H2O mass loss from subsurface brines was calculated as a function of latitude, depth, regolith porosity, eutectic temperature, and pore size. A model for a chemically reasonable brine that could reproduce Martian radar results was developed, and the escape rate of H2O molecules from such a brine was estimated. It is suggested that the presence of a low-permeability duricrust may be required to preserve such a brine for reasonable periods, and to prevent detection of an extensive subsurface system by the Viking MAWD instrument.

  5. Carbonate and carbon isotopic evolution of groundwater contaminated by produced water brine with hydrocarbons

    International Nuclear Information System (INIS)

    Atekwana, Eliot A.; Seeger, Eric J.

    2015-01-01

    The major ionic and dissolved inorganic carbon (DIC) concentrations and the stable carbon isotope composition of DIC (δ"1"3C_D_I_C) were measured in a freshwater aquifer contaminated by produced water brine with petroleum hydrocarbons. Our aim was to determine the effects of produced water brine contamination on the carbonate evolution of groundwater. The groundwater was characterized by three distinct anion facies: HCO_3"−-rich, SO_4"2"−-rich and Cl"−-rich. The HCO_3"−-rich groundwater is undergoing closed system carbonate evolution from soil CO_2_(_g_) and weathering of aquifer carbonates. The SO_4"2"−-rich groundwater evolves from gypsum induced dedolomitization and pyrite oxidation. The Cl"−-rich groundwater is contaminated by produced water brine and undergoes common ion induced carbonate precipitation. The δ"1"3C_D_I_C of the HCO_3"−-rich groundwater was controlled by nearly equal contribution of carbon from soil CO_2_(_g_) and the aquifer carbonates, such that the δ"1"3C of carbon added to the groundwater was −11.6‰. In the SO_4"2"−-rich groundwater, gypsum induced dedolomitization increased the "1"3C such that the δ"1"3C of carbon added to the groundwater was −9.4‰. In the produced water brine contaminated Cl"−-rich groundwater, common ion induced precipitation of calcite depleted the "1"3C such that the δ"1"3C of carbon added to the groundwater was −12.7‰. The results of this study demonstrate that produced water brine contamination of fresh groundwater in carbonate aquifers alters the carbonate and carbon isotopic evolution. - Highlights: • We studied carbonate and δ"1"3C evolution in groundwater contaminated by produced water brine. • Multiple processes affect the carbonate and δ"1"3C evolution of the groundwater. • The processes are carbonate weathering, dedolomitization and common ion induce calcite precipitation. • The δ"1"3C added to DIC was −11.6‰ for weathering, −9.4‰ for dedolomitization

  6. Evolution of wettability in terms of petroleum and petroleum fractions adsorption. An approach by the Wilhelmy method; Evolution de la mouillabilite en fonction de l`adsorption du petrole et de ses fractions. Approche par la methode des angles de contact dynamiques

    Energy Technology Data Exchange (ETDEWEB)

    Mattos Saliba, A

    1996-12-06

    Reservoir wettability is very important to petroleum recovery by waterflooding and other processes. It is a key parameter controlling multiphase flow and fluids distribution in a porous medium. Nevertheless, the original water-wetness can be modified by the petroleum`s natural surfactants (asphaltenes and resins) adsorption onto the rock surface. This adsorption may reduce petroleum recovery. In this study, the adsorption of model molecules (pyridine and benzo-quinoline), of rude oil and of its heavier fractions (asphaltenes and resins) has been investigated in terms of wettability alteration for initially water-wet surfaces (glass or quartz). In this case, the dynamic Wilhelmy plate technique provides quantitative values of wetting preference to either oil or water. The results show that, at ambient conditions, adsorption depends on concentration, adsorbent/adsorbate interaction time, pH, solvent type, substrate surface, brine concentration and environment liquid phase (water or oil). However, the initial water film on the surface does not strongly influence this phenomena. (author) 222 refs.

  7. Brine Pockets in the Icy Shell on Europa: Distribution, Chemistry, and Habitability

    Science.gov (United States)

    Zolotov, M. Yu; Shock, E. L.; Barr, A. C.; Pappalardo, R. T.

    2004-01-01

    On Earth, sea ice is rich in brine, salt, and gas inclusions that form through capturing of seawater during ice formation. Cooling of the ice over time leads to sequential freezing of captured sea-water, precipitation of salts, exsolution of gases, and formation of brine channels and pockets. Distribution and composition of brines in sea ice depend on the rate of ice formation, vertical temperature gradient, and the age of the ice. With aging, the abundance of brine pockets decreases through downward migration. De- spite low temperatures and elevated salinities, brines in sea ice provide a habitat for photosynthetic and chemosynthetic organisms. On Europa, brine pockets and channels could exist in the icy shell that may be from a few km to a few tens of km thick and is probably underlain by a water ocean. If the icy shell is relatively thick, convection could develop, affecting the temperature pattern in the ice. To predict the distribution and chemistry of brine pockets in the icy shell we have combined numerical models of the temperature distribution within a convecting shell, a model for oceanic chemistry, and a model for freezing of Europan oceanic water. Possible effects of brine and gas inclusions on ice rheology and tectonics are discussed.

  8. On the physico-chemical characteristics of brines

    Digital Repository Service at National Institute of Oceanography (India)

    Shirodkar, P.V.; Rao, P.V.S.S.D.P.; Singbal, S.Y.S.

    Analyses of the natural brines form the salt lakes, salt pans and the artificial brines obtained after the solar desalination of seawater respectively, showed wide differences in their physico-chemical characteristics. The natural brines are markEd...

  9. Gypsum and hydrohalite dynamics in sea ice brines

    Science.gov (United States)

    Butler, Benjamin M.; Papadimitriou, Stathys; Day, Sarah J.; Kennedy, Hilary

    2017-09-01

    Mineral authigenesis from their dissolved sea salt matrix is an emergent feature of sea ice brines, fuelled by dramatic equilibrium solubility changes in the large sub-zero temperature range of this cryospheric system on the surface of high latitude oceans. The multi-electrolyte composition of seawater results in the potential for several minerals to precipitate in sea ice, each affecting the in-situ geochemical properties of the sea ice brine system, the habitat of sympagic biota. The solubility of two of these minerals, gypsum (CaSO4 ·2H2O) and hydrohalite (NaCl · 2H2O), was investigated in high ionic strength multi-electrolyte solutions at below-zero temperatures to examine their dissolution-precipitation dynamics in the sea ice brine system. The gypsum dynamics in sea ice were found to be highly dependent on the solubilities of mirabilite and hydrohalite between 0.2 and - 25.0 ° C. The hydrohalite solubility between - 14.3 and - 25.0 ° C exhibits a sharp change between undersaturated and supersaturated conditions, and, thus, distinct temperature fields of precipitation and dissolution in sea ice, with saturation occurring at - 22.9 ° C. The sharp changes in hydrohalite solubility at temperatures ⩽-22.9 °C result from the formation of an ice-hydrohalite aggregate, which alters the structural properties of brine inclusions in cold sea ice. Favourable conditions for gypsum precipitation in sea ice were determined to occur in the region of hydrohalite precipitation below - 22.9 ° C and in conditions of metastable mirabilite supersaturation above - 22.9 ° C (investigated at - 7.1 and - 8.2 ° C here) but gypsum is unlikely to persist once mirabilite forms at these warmer (>-22.9 °C) temperatures. The dynamics of hydrohalite in sea ice brines based on its experimental solubility were consistent with that derived from thermodynamic modelling (FREZCHEM code) but the gypsum dynamics derived from the code were inconsistent with that indicated by its

  10. Facts 2006. The Norwegian petroleum sector

    International Nuclear Information System (INIS)

    Dokka, Ane; Midttun, Oeyvind

    2006-01-01

    The petroleum sector is extremely important to Norway. The industry is responsible for one fourth of all value creation in the country and more than one fourth of the state's revenues. It is currently Norway's largest industry, and the spillover effects to other industries are substantial. Norway ranks as the world's third largest exporter of oil and the eighth largest oil producer. Less than one third of the estimated petroleum reserves Norway has have been produced. The level of activity on the Norwegian continental shelf was very high in 2005. The number of producing fields was 50, and these fields produced 3 million barrels of oil (including NGL and condensate) per day and 85 billion standard cubic metres (scm) gas, for a total production saleable petroleum of 257 million scm of oil equivalents. Resource management is conducted through the models of cooperation and competition. Annual licensing rounds are held by the authorities where companies are given access to new exploration areas. The interest in the 19th licensing round in 2005 was considerable, indicating a continuous high interest in the Norwegian continental shelf. The Norwegian Petroleum Directorate estimates for the future a gradual increase in the petroleum production up until 2011, and a gradual fall thereafter. Gas production is expected to increase until 2013. Gas production represents 35 percent of the total production in 2006. It is expected that by 2013 it will represent 50 percent of the total. Other aspects accounted for include government petroleum revenues, environmental considerations, petroleum resources and overviews of fields in production, fields where production has ceased and fields under development

  11. BIOREMEDIATION OF A PETROLEUM-HYDROCARBON

    African Journals Online (AJOL)

    ES OBE

    under field conditions in the bioremediation of a petroleum- hydrocarbon polluted ... an accelerated biodegradation of petroleum hydrocarbons in a polluted agricultural soil ..... 12) Jackson, M.L. Soil chemical analysis. ... biological assay. 3 rd.

  12. Facts 2009 - The Norwegian petroleum sector; Fakta 2009 - norsk petroleumsverksemd

    Energy Technology Data Exchange (ETDEWEB)

    2009-07-01

    The publication provides a general overview of information regarding the petroleum activities on the Norwegian continental shelf. Contents: Foreword; The petroleum sector; Norwegian resource management; Government petroleum revenues; Exploration activities; Development and operations; Norwegian gas exports; Decommissioning; Research, technology; Environmental considerations; Petroleum resources; Fields in production; Fields under development; Future developments; Fields where production has ceased; Pipelines and onshore facilities. (AG)

  13. Petroleum environmental research forum field study on biofilters for control of volatile hydrocarbons

    International Nuclear Information System (INIS)

    Leson, G.; Smith, B.J.

    1997-01-01

    A field study on the treatment of volatile petroleum hydrocarbons (PHC) by biofiltration was conducted by the Petroleum Environmental Research Forum (PERF) between 1992 and 1994. Its objective was to assess the technical, regulatory, and economic feasibility of biofiltration for off-gases from petroleum processing and soil remediation equipment. It involved three small-scale biofilters provided by US vendors, treating off-gas from two soil vapor extraction sites and a source of refinery wastewater. Comprehensive monitoring of biofilter operating parameters and performance was conducted. Typically more than 95% of aromatic compounds such as benzene, and odorous reduced sulfur compounds can be removed at residence times of one minute or less, while removal of more than 70% of light aliphatics will require residence times of several minutes, and will thus require correspondingly large filter volumes and higher capital expenditure. The high percentage removal of aromatic hazardous air pollutants (HAP) and odors can generally be accomplished at comparatively short residence times while the need for high-percentage removal, particular of light aliphatics ( 5 ) will generally render biofiltration noncompetitive. Finally, a preliminary economic comparison of biofilters and established control technologies suggested that biofiltration may, for a representative design case involving off-gas from a refinery wastewater treatment operation, offer considerable savings in total cost of air pollution control for petroleum hydrocarbon streams if regulations require the control of aromatic HAP or odors

  14. Jarosite dissolution rates in perchlorate brine

    Science.gov (United States)

    Legett, Carey; Pritchett, Brittany N.; Elwood Madden, Andrew S.; Phillips-Lander, Charity M.; Elwood Madden, Megan E.

    2018-02-01

    Perchlorate salts and the ferric sulfate mineral jarosite have been detected at multiple locations on Mars by both landed instruments and orbiting spectrometers. Many perchlorate brines have eutectic temperatures bearing rocks and sediments may have been altered by perchlorate brines. Here we measured jarosite dissolution rates in 2 M sodium perchlorate brine as well as dilute water at 298 K to determine the effects of perchlorate anions on jarosite dissolution rates and potential reaction products. We developed a simple method for determining aqueous iron concentrations in high salinity perchlorate solutions using ultraviolet-visible spectrophotometry that eliminates the risk of rapid oxidation reactions during analyses. Jarosite dissolution rates in 2 M perchlorate brine determined by iron release rate (2.87 × 10-12 ±0.85 × 10-12 mol m-2 s-1) were slightly slower than the jarosite dissolution rate measured in ultrapure (18.2 MΩ cm-1) water (5.06 × 10-12 mol m-2 s-1) using identical methods. No additional secondary phases were observed in XRD analyses of the reaction products. The observed decrease in dissolution rate may be due to lower activity of water (ɑH2O = 0.9) in the 2 M NaClO4 brine compared with ultrapure water (ɑH2O = 1). This suggests that the perchlorate anion does not facilitate iron release, unlike chloride anions which accelerated Fe release rates in previously reported jarosite and hematite dissolution experiments. Since dissolution rates are slower in perchlorate-rich solutions, jarosite is expected to persist longer in perchlorate brines than in dilute waters or chloride-rich brines. Therefore, if perchlorate brines dominate aqueous fluids on the surface of Mars, jarosite may remain preserved over extended periods of time, despite active aqueous processes.

  15. Evaluation of Brine Processing Technologies for Spacecraft Wastewater

    Science.gov (United States)

    Shaw, Hali L.; Flynn, Michael; Wisniewski, Richard; Lee, Jeffery; Jones, Harry; Delzeit, Lance; Shull, Sarah; Sargusingh, Miriam; Beeler, David; Howard, Jeanie; hide

    2015-01-01

    Brine drying systems may be used in spaceflight. There are several advantages to using brine processing technologies for long-duration human missions including a reduction in resupply requirements and achieving high water recovery ratios. The objective of this project was to evaluate four technologies for the drying of spacecraft water recycling system brine byproducts. The technologies tested were NASA's Forward Osmosis Brine Drying (FOBD), Paragon's Ionomer Water Processor (IWP), NASA's Brine Evaporation Bag (BEB) System, and UMPQUA's Ultrasonic Brine Dewatering System (UBDS). The purpose of this work was to evaluate the hardware using feed streams composed of brines similar to those generated on board the International Space Station (ISS) and future exploration missions. The brine formulations used for testing were the ISS Alternate Pretreatment and Solution 2 (Alt Pretreat). The brines were generated using the Wiped-film Rotating-disk (WFRD) evaporator, which is a vapor compression distillation system that is used to simulate the function of the ISS Urine Processor Assembly (UPA). Each system was evaluated based on the results from testing and Equivalent System Mass (ESM) calculations. A Quality Function Deployment (QFD) matrix was also developed as a method to compare the different technologies based on customer and engineering requirements.

  16. Proceedings of the 2001 Canadian society of petroleum geologists annual convention

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    Founded in 1927 as the Alberta Society of Petroleum Geologists, the Canadian Society of Petroleum Geologists is dedicated to promote and further the study of petroleum and natural gas geology and all the study fields related to it. Its 3300 members represent Canada and 30 other countries. The annual convention is held to provide a forum for the exchange of information on topics related to petroleum geology and to foster the spirit of scientific research with the members. Another objective of the Society and annual convention is to make the general public aware of the need for professional and well-trained scientists. In excess of 100 presentations were made at the 2001 annual convention on topics that included petroleum potential in Somalia, seismic imaging, faulting and fault seal, multi-scale reservoir compartmentalization, non-invasive geochemical and remote sensing methods, and much more. refs., tabs., figs.

  17. Hydrogen and carbon isotopes of petroleum and related organic matter

    International Nuclear Information System (INIS)

    Yeh, H.W.; Epstein, S.

    1981-01-01

    D/H and 13 C/ 12 C ratios were measured for 114 petroleum samples and for several samples of related organic matter. DeltaD of crude oil ranges from -85 to -181 per thousand except for one distillate (-250 per thousand) from the Kenai gas field; delta 13 C of crude oil ranges from -23.3 to -32.5 per thousand. Variation in deltaD and delta 13 C values of compound-grouped fractions of a crude oil is small, 3 and 1.1 per thousand, respectively, and the difference in deltaD and delta 13 C between oil and coeval wax is slight. Gas fractions are 53 to 70 and 22.6 to 23.2 per thousand depleted in D and 13 C, respectively, relative to the coexisting oil fractions. The deltaD and delta 13 C values of the crude oils appear to be largely determined by the isotopic compositions of their organic precursors. The contribution of terrestrial organic debris to the organic precursors of most marine crude oils may be significant. (author)

  18. State information needs related to onshore and nearshore effects of OCS petroleum development

    Energy Technology Data Exchange (ETDEWEB)

    Williams, D.C.; Stang, P.R.; Hyde, B.

    1977-01-01

    The United States currently has underway a program to develop tracts on the Outer Continental Shelf (OCS) for their petroleum resources that can have significant impact on and near the shore. The potentially affected States bordering the Atlantic and Pacific Oceans and the Gulf of Mexico have expressed serious concerns about the availability and adequacy of the information they need to make planning and management decisions about onshore activities and impacts related to OCS petroleum development. This report discusses state policies, major concerns, organization, planning approaches and relation to other state planning efforts.

  19. Pressure-driven brine migration in a salt repository

    International Nuclear Information System (INIS)

    Hwang, Y.; Chambre, P.L.; Pigford, T.H.; Lee, W.W.L.

    1989-01-01

    The traditional view is that salt is the ideal rock for isolation of nuclear waste because it is ''dry'' and probably ''impermeable.'' The existence of salt through geologic time is prima facie evidence of such properties. Experiments and experience at potential salt sites for geologic repositories have indicated that while porosity and permeability of salt are low, the salt may be saturated with brine. If this hypothesis is correct, then it is possible to have brine flow due to pressure differences within the salt. If there is pressure-driven brine migration in salt repositories then it is paramount to know the magnitude of such flow because inward brine flow would affect the corrosion rate of nuclear waste containers and outward brine flow might affect radionuclide transport rates. Brine exists in natural salt as inclusions in salt crystals and in grain boundaries. Brine inclusions in crystals move to nearby grain boundaries when subjected to a temperature gradient, because of temperature-dependent solubility of salt. Brine in grain boundaries moves under the influence of a pressure gradient. When salt is mined to create a waste repository, brine from grain boundaries will migrate into the rooms, tunnels and boreholes because these cavities are at atmospheric pressure. After a heat-emitting waste package is emplaced and backfilled, the heat will impose a temperature gradient in the surrounding salt that will cause inclusions in the nearby salt to migrate to grain boundaries within a few years, adding to the brine that was already present in the grain boundaries. The formulation of brine movement with salt as a thermoelastic porous medium, in the context of the continuum theory of mixtures, has been described. In this report we show the mathematical details and discuss the results predicted by this analysis

  20. Formation of brine channels in sea ice.

    Science.gov (United States)

    Morawetz, Klaus; Thoms, Silke; Kutschan, Bernd

    2017-03-01

    Liquid salty micro-channels (brine) between growing ice platelets in sea ice are an important habitat for CO 2 -binding microalgaea with great impact on polar ecosystems. The structure formation of ice platelets is microscopically described and a phase field model is developed. The pattern formation during solidification of the two-dimensional interstitial liquid is considered by two coupled order parameters, the tetrahedricity as structure of ice and the salinity. The coupling and time evolution of these order parameters are described by a consistent set of three model parameters. They determine the velocity of the freezing process and the structure formation, the phase diagram, the super-cooling and super-heating region, and the specific heat. The model is used to calculate the short-time frozen micro-structures. The obtained morphological structure is compared with the vertical brine pore space obtained from X-ray computed tomography.

  1. Basic petroleum research. Final report

    International Nuclear Information System (INIS)

    Roesjoe, Bjarne; Stiksrud, Helge

    2004-01-01

    An overview of projects in the field of basic petroleum research (PetroForsk) is presented. A brief presentation of some of the projects is included, as well as political comments on the value of these projects. The research program Basic Petroleum Research (PetroForsk) was established in 1998 and ended in 2004. The program has been part of the Research Council of Norway's long-term effort in petroleum research (ml)

  2. Field portable petroleum analysis for validation of the site characterization and analysis penetrometer system petroleum, oil and lubricant sensor

    International Nuclear Information System (INIS)

    Davis, W.M.; Jones, P.; Porter, B.

    1995-01-01

    A petroleum, oil and lubricant (POL) sensor for the Site Characterization and Analysis Penetrometer System (SCAPS) has been developed by the Tri-Services (e.g. Army, Navy and Air Force) to characterize the distribution of POL contaminants on military sites. The sensor is based on the detection of POL contaminants using a laser induced fluorescence (LIF) spectrometer. The SCAPS POL sensor has been shown to be a valuable tool for the rapid screening of POL contamination in the subsurface. However, many factors can affect the LIF response of a particular fuel at a particular site. These include fuel type, age of spill (e.g. weathering) and soil type. The LIF sensor also detects fluorescence from any naturally occurring fluorophores, including humic substances and fluorescent minerals. These factors lead to the development of an independent procedure for the verification of the POL sensor response. This paper describes a field portable total recoverable petroleum hydrocarbon (TRPH) method based on EPA Method 418.1 and its application to on site validation of the SCAPS POL sensor response at a number of contaminated sites

  3. Durability of concrete materials in high-magnesium brine

    International Nuclear Information System (INIS)

    Wakeley, L.D.; Poole, T.S.; Burkes, J.P.

    1994-03-01

    Cement pastes and mortars representing 11 combinations of candidate concrete materials were cast in the laboratory and monitored for susceptibility to chemical deterioration in high-magnesium brine. Mixtures were selected to include materials included in the current leading candidate concrete for seals at the Waste Isolation Pilot Plant (WIPP). Some materials were included in the experimental matrix to answer questions that had arisen during study of the concrete used for construction of the liner of the WIPP waste-handling shaft. Mixture combinations compared Class C and Class F fly ashes, presence or absence of an expansive component, and presence or absence of salt as a mixture component. Experimental conditions exposed the pastes and mortars to extreme conditions, those being very high levels of Mg ion and an effectively unlimited supply of brine. All pastes and mortars showed deterioration with brine exposure. In general, mortars deteriorated more extensively than the corresponding pastes. Two-inch cube specimens of mortar were not uniformly deteriorated, but showed obvious zoning even after a year in the brine, with a relatively unreacted zone remaining at the center of each cube. Loss of calcium from the calcium hydroxide of paste/aggregate interfaces caused measurable strength loss in the reacted zone comprising the outer portion of every mortar specimen. The current candidate mass concrete for WIPP seals includes salt as an initial component, and has a relatively closed initial microstructure. Both of these features contribute to its suitability for use in large placements within the Salado Formation

  4. Relative permeabilities of supercritical CO2 and brine in carbon sequestration by a two-phase lattice Boltzmann method

    Science.gov (United States)

    Xie, Jian.-Fei.; He, S.; Zu, Y. Q.; Lamy-Chappuis, B.; Yardley, B. W. D.

    2017-08-01

    In this paper, the migration of supercritical carbon dioxide (CO2) in realistic sandstone rocks under conditions of saline aquifers, with applications to the carbon geological storage, has been investigated by a two-phase lattice Boltzmann method (LBM). Firstly the digital images of sandstone rocks were reproduced utilizing the X-ray computed microtomography (micro-CT), and high resolutions (up to 2.5 μm) were applied to the pore-scale LBM simulations. For the sake of numerical stability, the digital images were "cleaned" by closing the dead holes and removing the suspended particles in sandstone rocks. In addition, the effect of chemical reactions occurred in the carbonation process on the permeability was taken into account. For the wetting brine and non-wetting supercritical CO2 flows, they were treated as the immiscible fluids and were driven by pressure gradients in sandstone rocks. Relative permeabilities of brine and supercritical CO2 in sandstone rocks were estimated. Particularly the dynamic saturation was applied to improve the reliability of the calculations of the relative permeabilities. Moreover, the effects of the viscosity ratio of the two immiscible fluids and the resolution of digital images on the relative permeability were systematically investigated.

  5. Salton Sea geothermal field as a natural analog for the near-field in a salt high-level nuclear waste repository

    International Nuclear Information System (INIS)

    Elders, W.A.; Moody, J.B.; Battelle Memorial Inst., Columbus, OH)

    1984-01-01

    The Salton Sea Geothermal Field (SSGF), on the delta of the Colorado River in southern California, is being studied as a natural analog for the near-field environment of proposed nuclear waste repositories in salt. A combination of mineralogical and geochemical methods is being employed to develop a three-dimenisonal picture of temperature, salinity, lithology, mineralogy, and chemistry of reactions between the reservoir rocks and the hot brines. Our aim is to obtain quantitative data on mineral stabilities and on mobilities of the naturally occurring radionuclides of concern in Commercial High-Level Waste (CHLW). These data will be used to validate the EQ3/6 geochemical code under development to model the salt near-field repository behavior. Maximum temperatures encountered in wells in the SSGF equal or exceed peak temperatures expected in a salt repository. Brines produced from these wells have major element chemistry similar to brines from candidate salt sites. Relative to the rocks, these brines are enriched in Na, Mn, Sr, Ra, and Po, depleted in Ba, Si, Mg, Ti, and Al, and strongly depleted in U and Th. However, the unaltered rocks contain only about 2 to 3 ppm of U and 4 to 12 ppm of Th, largely in detrital epidotes and zircons. Samples of hydrothermally altered rocks from a wide range of temperature and salinity show rather similar uniform low concentrations of these elements, even when authigenic illite, chlorite, ipidote and feldspar are present. These observations suggest that U and Th are relatively immobile in these hot brines. However, Ra, Po, Cs, and Sr are relatively mobile. Work is continuing to document naturally occurring radionuclide partitioning between SSGF minears and brine over a range of temperature, salinity, and lithology. 8 refs., 7 figs., 2 tabs

  6. Migration of brine inclusions in salt

    International Nuclear Information System (INIS)

    Pigford, T.H.

    1982-01-01

    Theories of the migration of brine inclusions in salt are interpreted as simple physical processes, and theories by Russian and U.S. workers are shown to yield the same results. The migration theory is used to predict threshold temperature gradients below which migration of brine inclusions should not occur. The predicted threshold gradients are compared with the temperature gradients expected at the Waste Isolation Pilot Plant in New Mexico. The theory of a threshold gradient helps explain the existence of brine inclusions in natural salt deposits

  7. Recovery of Fresh Water Resources from Desalination of Brine Produced During Oil and Gas Production Operations

    Energy Technology Data Exchange (ETDEWEB)

    David B. Burnett; Mustafa Siddiqui

    2006-12-29

    Management and disposal of produced water is one of the most important problems associated with oil and gas (O&G) production. O&G production operations generate large volumes of brine water along with the petroleum resource. Currently, produced water is treated as a waste and is not available for any beneficial purposes for the communities where oil and gas is produced. Produced water contains different contaminants that must be removed before it can be used for any beneficial surface applications. Arid areas like west Texas produce large amount of oil, but, at the same time, have a shortage of potable water. A multidisciplinary team headed by researchers from Texas A&M University has spent more than six years is developing advanced membrane filtration processes for treating oil field produced brines The government-industry cooperative joint venture has been managed by the Global Petroleum Research Institute (GPRI). The goal of the project has been to demonstrate that treatment of oil field waste water for re-use will reduce water handling costs by 50% or greater. Our work has included (1) integrating advanced materials into existing prototype units and (2) operating short and long-term field testing with full size process trains. Testing at A&M has allowed us to upgrade our existing units with improved pre-treatment oil removal techniques and new oil tolerant RO membranes. We have also been able to perform extended testing in 'field laboratories' to gather much needed extended run time data on filter salt rejection efficiency and plugging characteristics of the process train. The Program Report describes work to evaluate the technical and economical feasibility of treating produced water with a combination of different separation processes to obtain water of agricultural water quality standards. Experiments were done for the pretreatment of produced water using a new liquid-liquid centrifuge, organoclay and microfiltration and ultrafiltration membranes

  8. Toxicology of oil field wastes. Hazards to livestock associated with the petroleum industry.

    Science.gov (United States)

    Edwards, W C

    1989-07-01

    In oil-producing states, the proximity of livestock to drilling operations and production sites often results in poisoning of animals from ingestion of crude oil, condensate, salt water, heavy metals, and caustic chemicals. The heavy metals encountered most frequently are lead from pipe joint compound and arsenicals and chromates used as corrosion inhibitors. Numerous toxic and caustic chemicals are used in drilling muds and fluids. Crude oil and salt water spills are common occurrences around production sites. Pipeline breaks may result in exposure of livestock to crude oil or refined petroleum hydrocarbons. Ingestion of petroleum hydrocarbons may result in sudden death from peracute bloat. The most common cause of illness or death following exposure to petroleum hydrocarbons is aspiration pneumonia, which may cause a chronic progressive deterioration of health, with death after several days or weeks. Cases in which livestock are exposed to oil, salt water, or caustic chemicals, but do not die acutely or from aspiration pneumonia are more frustrating to diagnose. In these cases, parasitism, poor nutrition, and other debilitating diseases must be considered. Anorexia, weight loss, and decreased rumen motility may be caused by a disruption of normal rumen function. Petroleum hydrocarbons, salt water, and caustic chemicals have the potential of altering rumen flora and enzymatic processes as well as damaging the ruminal and gastrointestinal epithelium. The toxicity of petroleum hydrocarbons appears to be related more closely to the volatility and viscosity of the product than to other factors. The more volatile straight chain and aromatic petroleum hydrocarbons have a greater potential for aspiration pneumonia and may produce an anesthetic-like action if absorbed systemically. The more volatile petroleum hydrocarbons also are more irritating to skin and mucous membranes and appear to be more damaging to rumen flora. Treatment of petroleum hydrocarbon ingestion is

  9. Chemistry of brines in salt from the Waste Isolation Pilot Plant (WIPP), southeastern New Mexico: a preliminary investigation

    International Nuclear Information System (INIS)

    Stein, C.L.; Krumhansl, J.L.

    1986-03-01

    We present here analyses of macro- and microscopic (intracrystalline) brines observed within the WIPP facility and in the surrounding halite, with interpretations regarding the origin and history of these fluids and their potential effect(s) on long-term waste storage. During excavation, several large fluid inclusions were recovered from an area of highly recrystallized halite in a thick salt bed at the repository horizon (2150 ft below ground level). In addition, 52 samples of brine ''weeps'' were collected from walls of recently excavated drifts at the same stratigraphic horizon from which the fluid inclusion samples are assumed to have been taken. Analyses of these fluids show that they differ substantially in composition from the inclusion fluids and cannot be explained by mixing of the fluid inclusion populations. Finally, holes in the facility floor that filled with brine were sampled but with no stratographic control; therefore it is not possible to interpret the compositions of these brines with any accuracy, except insofar as they resemble the weep compositions but with greater variation in both K/Mg and Na/Cl ratios. However, the Ca and SO 4 values for the floor holes are relatively close to the gypsum saturation curve, suggesting that brines filling floor holes have been modified by the presence of gypsum or anhydrite, possibly even originating in one or more of the laterally continuous anhydrite units referred to in the WIPP literature as marker beds. In conclusion, the wide compositional variety of fluids found in the WIPP workings suggest that (1) an interconnected hydrologic system which could effectively transport radonuclides away from the repository does not exist; (2) brine migration studies and experiments must consider the mobility of intergranular fluids as well as those in inclusions; and (3) near- and far-field radionuclide migration testing programs need to consider a wide range of brine compositions rather than a few reference brines

  10. Capillary pressure - saturation relations for supercritical CO2 and brine: Implications for capillary/residual trapping in carbonate reservoirs during geologic carbon sequestration

    Science.gov (United States)

    Wang, S.; Tokunaga, T. K.

    2014-12-01

    In geologic carbon sequestration (GCS), data on capillary pressure (Pc) - saturation (Sw) relations are routinely needed to appraise reservoir processes. Capillarity and its hysteresis have been often experimentally studied in oil-water, gas-water and three phase gas-oil-water systems, but fewer works have been reported on scCO2-water under in-situ reservoir conditions. Here, Pc-Sw relations of supercritical (sc) CO2 displacing brine, and brine rewetting the porous medium to trap scCO2 were studied to understand CO2 transport and trapping behavior in carbonate reservoirs under representative reservoir conditions. High-quality drainage and imbibition (and associated capillary pressure hysteresis) curves were measured under elevated temperature and pressure (45 ºC, 8.5 and 12 MPa) for scCO2-brine as well as at room temperature and pressure (23 ºC, 0.1 MPa) for air-brine in unconsolidated limestone and dolomite sand columns using newly developed semi-automated multistep outflow-inflow porous plate apparatus. Drainage and imbibition curves for scCO2-brine deviated from the universal scaling curves for hydrophilic interactions (with greater deviation under higher pressure) and shifted to lower Pc than predicted based on interfacial tension (IFT) changes. Augmented scaling incorporating differences in IFT and contact angle improved the scaling results but the scaled curves still did not converge onto the universal curves. Equilibrium residual trapping of the nonwetting phase was determined at Pc =0 during imbibition. The capillary-trapped amounts of scCO2 were significantly larger than for air. It is concluded that the deviations from the universal capillary scaling curves are caused by scCO2-induced wettability alteration, given the fact that pore geometry remained constant and IFT is well constrained. In-situ wettability alteration by reactive scCO2 is of critical importance and must be accounted for to achieve reliable predictions of CO2 behavior in GCS reservoirs.

  11. Brine Extraction and Treatment Strategies to Enhance Pressure Management and Control of CO2 Plumes in Deep Geologic Formations

    Energy Technology Data Exchange (ETDEWEB)

    Okwen, Roland [Univ. of Illinois, Champaign, IL (United States). Prairie Research Inst.; Frailey, Scott [Univ. of Illinois, Champaign, IL (United States). Prairie Research Inst.; Dastgheib, Seyed [Univ. of Illinois, Champaign, IL (United States). Prairie Research Inst.

    2017-06-14

    The overall goal of the this project is to develop and validate pressure management and carbon dioxide (CO2) plume control strategies that can address technical and economic barriers to commercial deployment of CO2 storage technologies, based on computational and field demonstration work at the Archer Daniels Midland Company (ADM) facility where the Illinois Basin–Decatur Project (IBDP) and the Illinois-Industrial Carbon Capture and Storage (IL-ICCS) projects are located. To accomplish the overall goal, the ISGS designed a brine extraction storage test (BEST) that could be completed in two phases. The goal of BEST Phase I was to evaluate the feasibilities of extraction well(s) placement, the brine extraction to CO2 injection rate ratio, extraction well completion, and brine treatment and handling. The goal of BEST Phase II would be to validate the brine extraction and treatment options deemed feasible in Phase I by (1) demonstrating the efficacy of brine extraction (BE) in managing pressure (i.e., formation) and the CO2 plume, and (2) demonstrating treatment of extracted brine with high total dissolved solids (TDS; >200,000 mg/L) using multiple advanced treatment technologies. This report details work done in Phase I. Several brine extraction and treatment scenarios were tested, simulated, and analyzed for their effectiveness in extracting brine. Initially a vertical well was studied; however, geologic modeling, reservoir modeling, and the existing facility and wellbore infrastructure dictated that the location of a vertical brine extraction well was limited to an area with no existing monitoring wells and where the well would be in relative proximity to an existing CO2 plume. Consequently, a vertical well was excluded, and a horizontal brine extraction well placed above the existing CO2 plume near two existing wells was studied. The horizontal well option allows the project to leverage the

  12. Brine migration in hot-pressed polycrystalline sodium chloride

    International Nuclear Information System (INIS)

    Biggers, J.V.; Dayton, G.O.

    1982-12-01

    This report describes experiments designed to provide data on brine migration in polycrystalline salt. Polycrystalling samples of various grain sizes, density, and purity were prepared from several commercial-grade salts by hot-pressing. Three distinct experimental set-ups were used to place salt billets in an induced thermal gradient in contact with brine source. The test designs varied primarily in the way in which the thermal gradient was applied and monitored and the way in which brine migration was determined. All migration was in enclosed vessels which precluded visual observation of brine movement through the microstructure. Migration velocities were estimated either by the timed appearance of brine at the hot face of the sample, or by determination of the penetration distance of migration artifacts in the microstructure after tests of fixed duration. For various reasons both of these methods were subject to a large degree of error. Our results suggest, however, that the migration velocity in dense polycrystalline salt may be at least an order of magnitude greater than that suggested by single-crystal experiments. Microstructural analysis shows that brine prefers to migrate along paths of high crystalline activity such as grain and subgrain boundaries and is dispersed rather quickly in the microstructure. A series of tests were performed using various types of tracers in brine in order to flag migration paths and locate brine in the microstructure more decisively. These attempts failed and it appears that only the aqueous portion of the brine moves through the microstructure with the dissolved ions being lost and replaced rather quickly. This suggests the use of deuterium as a tracer in future work

  13. Effects of high salinity from desalination brine on growth, photosynthesis, water relations and osmolyte concentrations of seagrass Posidonia australis

    International Nuclear Information System (INIS)

    Cambridge, M L; Zavala-Perez, A; Cawthray, G R; Mondon, J; Kendrick, G A

    2017-01-01

    Highly saline brines from desalination plants expose seagrass communities to salt stress. We examined effects of raised salinity (46 and 54 psu) compared with seawater controls (37 psu) over 6 weeks on the seagrass, Posidonia australis, growing in tanks with the aim of separating effects of salinity from other potentially deleterious components of brine and determining appropriate bioindicators. Plants survived exposures of 2–4 weeks at 54 psu, the maximum salinity of brine released from a nearby desalination plant. Salinity significantly reduced maximum quantum yield of PSII (chlorophyll a fluorescence emissions). Leaf water potential (Ψ w ) and osmotic potential (Ψ π ) were more negative at increased salinity, while turgor pressure (Ψ p ) was unaffected. Leaf concentrations of K + and Ca 2+ decreased, whereas concentrations of sugars (mainly sucrose) and amino acids increased. We recommend leaf osmolarity, ion, sugar and amino acid concentrations as bioindicators for salinity effects, associated with brine released in desalination plant outfalls. - Highlights: • We separated salt effects of desalination brine from other deleterious components. • Sublethal salinity stress depended on both salinity increase and exposure time. • Very effective osmoregulation led to tolerance of short intervals of high salinity.

  14. Measurement and modeling of CO2 solubility in NaCl brine and CO2–saturated NaCl brine density

    DEFF Research Database (Denmark)

    Yan, Wei; Huang, Shengli; Stenby, Erling Halfdan

    2011-01-01

    over climate change and energy security. This work is an experimental and modeling study of two fundamental properties in high pressure CO2–NaCl brine equilibrium, i.e., CO2 solubility in NaCl brine and CO2–saturated NaCl brine density. A literature review of the available data was presented first...

  15. Ice Control with Brine on Highways

    DEFF Research Database (Denmark)

    Bolet, Lars

    traffic flow the spread rate of pure sodium chloride (and thus the environmental impact) in the pre-salting operations was cut back by more than one third. Compared to neighbouring counties the use of salt is less than fifty percent per square meter. In addition, supply of brine from two mixer...... of interpreting this information. The improvements gained by the county of Funen were mainly due to the use of technologies (brine spreading with nozzles) giving a more precise spread pattern than the traditional gritting of pre-wetted salt. Major challenges in the process have been to verify the higher quality...... of the nozzles spread pattern, to ensure maximum utilization of volume of brine carried by the spreading vehicles and to control the mixing of brine without getting stratification in the mixture. Moreover, of course, to ensure political approval of abandoning a well-served technology and to organize...

  16. Strategic petroleum reserve, Byran Mound Salt Dome, Brazoria County, Texas. Final environmental impact statement (final supplement to FEA FES 76/77-6)

    Energy Technology Data Exchange (ETDEWEB)

    1977-12-01

    On January 7, 1977, the Federal Energy Administration issued a Final Environmental Impact Statement (EIS) for the development of the Bryan Mound salt dome as a storage site for the Strategic Petroleum Reserve (FES 76/77-6). On October 1, 1977, the U.S. Department of Energy was created and the programs of the Federal Energy Administration were transferred to the new Department. As such, this final supplement is being issued by the Department of Energy. The salt dome is located in Brazoria County, Texas. Since the EIS was published, it has been determined that this arrangement would be inadequate to meet the long term requirements for filling and withdrawing oil at the site, although the disposal of brine to Dow Chemical would be utilized to the maximum extent possible. Therefore, on July 15, 1977, a Draft Supplement to FES 76/77-6 was issued addressing the environmental impacts of construction and operation of two types of brine disposal systems and a new water supply system. This final supplement addresses a brine injection well system and a water intake system. Construction of this new system component would cause temporary disruption to land use, water quality, air quality, and terrestrial and aquatic ecology. The new facilities would permanently change 17 acres of land from its present use. Operation of the systems would have relatively small, short-term impacts. Use of the brine surge pit could adversely affect air quality by emitting hydrocarbon vapors (maximum rate of 51.4 tons per year). Operation of the disposal wells would increase the salinity of an already saline aquifer. All operational impacts would be relatively minor and short-term, occurring only during periods of fill or withdrawal of the storage facility.

  17. Modeling Coupled THMC Processes and Brine Migration in Salt at High Temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Rutqvist, Jonny; Blanco Martin, Laura; Mukhopadhyay, Sumit; Houseworth, Jim; Birkholzer, Jens

    2014-08-14

    In this report, we present FY2014 progress by Lawrence Berkeley National Laboratory (LBNL) related to modeling of coupled thermal-hydrological-mechanical-chemical (THMC) processes in salt and their effect on brine migration at high temperatures. LBNL’s work on the modeling of coupled THMC processes in salt was initiated in FY2012, focusing on exploring and demonstrating the capabilities of an existing LBNL modeling tool (TOUGH-FLAC) for simulating temperature-driven coupled flow and geomechanical processes in salt. This work includes development related to, and implementation of, essential capabilities, as well as testing the model against relevant information and published experimental data related to the fate and transport of water. we provide more details on the FY2014 work, first presenting updated tools and improvements made to the TOUGH-FLAC simulator, and the use of this updated tool in a new model simulation of long-term THM behavior within a generic repository in a salt formation. This is followed by the description of current benchmarking and validations efforts, including the TSDE experiment. We then present the current status in the development of constitutive relationships and the dual-continuum model for brine migration. We conclude with an outlook for FY2015, which will be much focused on model validation against field experiments and on the use of the model for the design studies related to a proposed heater experiment.

  18. Geochemistry of metal-rich brines from central Mississippi Salt Dome basin, U.S.A.

    Science.gov (United States)

    Kharaka, Y.K.; Maest, A.S.; Carothers, W.W.; Law, L.M.; Lamothe, P.J.; Fries, T.L.

    1987-01-01

    Oil-field brines are the most favored ore-forming solutions for the sediment-hosted Mississippi Valley-type ore deposits. Detailed inorganic and organic chemical and isotope analyses of water and gas samples from six oil fields in central Mississippi, one of the very few areas with high metal brines, were conducted to study the inorganic and organic complexes responsible for the high concentrations of these metals. The samples were obtained from production zones consisting of sandstone and limestone that range in depth from 1900 to 4000 m (70-120??C) and in age from Late Cretaceous to Late Jurassic. Results show that the waters are dominantly bittern brines related to the Louann Salt. The brines have extremely high salinities that range from 160,000 to 320,000 mg/l total dissolved solids and are NaCaCl-type waters with very high concentrations of Ca (up to 48,000 mg/l) and other alkaline-earth metals, but with low concentrations of aliphatic acid anions. The concentrations of metals in many water samples are very high, reaching values of 70 mg/l for Pb, 245 mg/l for Zn, 465 mg/l for Fe and 210 mg/l for Mn. The samples with high metal contents have extremely low concentrations (<0.02 mg/l) of H2S. Samples obtained from the Smackover Formation (limestone) have low metal contents that are more typical of oil-field waters, but have very high concentrations (up to 85 mg/l) of H2S. Computations with the geochemical code SOLMINEQ.87 give the following results: (1) both Pb and Zn are present predominantly as aqueous chloride complexes (mainly as PbCl42- and ZnCl42-, respectively); (2) the concentrations of metals complexed with short-chained aliphatic acid anions and reduced S species are minor; (3) organic acid anions are important in controlling the concentrations of metals because they affect the pH and buffer capacity of the waters at subsurface conditions; and (4) galena and sphalerite solubilities control the concentrations of Pb and Zn in these waters. ?? 1988.

  19. Origin and Evolution of Li-rich Brines at Clayton Valley, Nevada, USA

    Science.gov (United States)

    Munk, L. A.; Bradley, D. C.; Hynek, S. A.; Chamberlain, C. P.

    2011-12-01

    be an important process in the brine evolution. This is evident because of the increase in Na concentration as a function of enrichment in δD for most brine samples. In contrast the non-brine waters flowing into the basin show an increase in Na at relatively constant δD indicating little evaporation. The δD of clays sampled throughout a sediment core extending to 354 m below the surface show fluctuations that likely indicate warmer and cooler periods through time. Further investigation of the relationship of past climate and Li accumulation is in progress.

  20. Waste glass/metal interactions in brines

    International Nuclear Information System (INIS)

    Shade, J.W.; Pederson, L.R.; McVay, G.L.

    1983-05-01

    Leaching studies of MCC 76-68 glass in synthetic brines high in NaCl were performed from 50 to 150 0 C and included interactive testing with ductile iron and titanium. Hydrolysis of the glass matrix was generally slower in saturated brines than in deionized water, due to a lower solubility of silica in the brines. Inclusion of ductile iron in the tests resulted in accelerated leach rates because irion-silica reactions occurred which reduced the silica saturation fraction. At 150 0 C, iron also accelerated the rate of crystalline reaction product formation which were primarily Fe-bearing sepiolite and talc. 16 references

  1. Norwegian Petroleum Activity 97. Fact Sheet

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report is the official governmental review of the offshore operations on the Norwegian Continental Shelf in 1996. It covers the following topics: (1) Summary, (2) Historical overview, (3) State organization of petroleum activities, (4) The economic impact of Norwegian oil and gas, (5) State revenues, (6) Mainland activities, (7) Petroleum resources, (8) Production, (9) Marketing situation for petroleum products, (10) Environmental aspects, (11) The legal and license framework, (12) Licensing rounds, (13) Exploration, (14) Fields in production, (15) Fields under development, (16) Discoveries with development plan under consideration, (17) Transportation systems, (18) License interests, (19) Company interests, (20) White papers, (21) Useful postal addresses. 24 figs., 16 tabs.

  2. Petroleum and international policy

    International Nuclear Information System (INIS)

    Pertuzio, A.

    2002-01-01

    To illustrate the relation between the petroleum and the international policy, the author presents the place of the petroleum industry in the international relations by an analysis of the historical aspects, the states and international organizations interventions and the prices evolution. (A.L.B.)

  3. Power Scaling of Petroleum Field Sizes and Movie Box Office Earnings.

    Science.gov (United States)

    Haley, J. A.; Barton, C. C.

    2017-12-01

    The size-cumulative frequency distribution of petroleum fields has long been shown to be power scaling, Mandelbrot, 1963, and Barton and Scholz, 1995. The scaling exponents for petroleum field volumes range from 0.8 to 1.08 worldwide and are used to assess the size and number of undiscovered fields. The size-cumulative frequency distribution of movie box office earnings also exhibits a power scaling distribution for domestic, overseas, and worldwide gross box office earnings for the top 668 earning movies released between 1939 and 2016 (http://www.boxofficemojo.com/alltime/). Box office earnings were reported in the dollars-of-the-day and were converted to 2015 U.S. dollars using the U.S. consumer price index (CPI) for domestic and overseas earnings. Because overseas earnings are not reported by country and there is no single inflation index appropriate for all overseas countries. Adjusting the box office earnings using the CPI index has two effects on the power functions fit. The first is that the scaling exponent has a narrow range (2.3 - 2.5) between the three data sets; and second, the scatter of the data points fit by the power function is reduced. The scaling exponents for the adjusted value are; 2.3 for domestic box office earnings, 2.5 for overseas box office earnings, and 2.5 worldwide box office earnings. The smaller the scaling exponent the greater the proportion of all earnings is contributed by a smaller proportion of all the movies: where E = P (a-2)/(a-1) where E is the percentage of earnings, P is the percentage of all movies in the data set. The scaling exponents for box office earnings (2.3 - 2.5) means that approximately 20% of the top earning movies contribute 70-55% of all the earnings for domestic, worldwide earnings respectively.

  4. REFUSE OF FERMENTATION BRINES IN THE CUCUMBER PICKLING INDUSTRY

    Science.gov (United States)

    The project evaluated on a commercial scale the technological and economic feasibility of recycling spent cucumber fermentation brine. Two brine treatment procedures, heat treatment and chemical treatment, were used. The results showed that brine recycling was practical on a comm...

  5. The effect of plants on the degradation and toxicity of petroleum contaminants in soil: a field assessment.

    Science.gov (United States)

    Banks, M K; Schwab, P; Liu, B; Kulakow, P A; Smith, J S; Kim, R

    2003-01-01

    A field project located at the US Naval Base at Port Hueneme, California was designed to evaluate changes in contaminant concentrations and toxicity during phytoremediation. Vegetated plots were established in petroleum (diesel and heavy oil) contaminated soil and were evaluated over a two-year period. Plant species were chosen based on initial germination studies and included native California grasses. The toxicity of the impacted soil in vegetated and unvegetated plots was evaluated using Microtox, earthworm, and seed germination assays. The reduction of toxicity was affected more by contaminant aging than the establishment of plants. However, total petroleum hydrocarbon concentrations were lower by the end of the study in the vegetated plots when compared to the unvegetated soil. Although phytoremediation is an effective approach for cleaning-up of petroleum contaminated soil, a long-term management plan is required for significant reductions in contaminant concentrations.

  6. Effects of high salinity from desalination brine on growth, photosynthesis, water relations and osmolyte concentrations of seagrass Posidonia australis.

    Science.gov (United States)

    Cambridge, M L; Zavala-Perez, A; Cawthray, G R; Mondon, J; Kendrick, G A

    2017-02-15

    Highly saline brines from desalination plants expose seagrass communities to salt stress. We examined effects of raised salinity (46 and 54psu) compared with seawater controls (37psu) over 6weeks on the seagrass, Posidonia australis, growing in tanks with the aim of separating effects of salinity from other potentially deleterious components of brine and determining appropriate bioindicators. Plants survived exposures of 2-4weeks at 54psu, the maximum salinity of brine released from a nearby desalination plant. Salinity significantly reduced maximum quantum yield of PSII (chlorophyll a fluorescence emissions). Leaf water potential (Ψ w ) and osmotic potential (Ψ π ) were more negative at increased salinity, while turgor pressure (Ψ p ) was unaffected. Leaf concentrations of K + and Ca 2+ decreased, whereas concentrations of sugars (mainly sucrose) and amino acids increased. We recommend leaf osmolarity, ion, sugar and amino acid concentrations as bioindicators for salinity effects, associated with brine released in desalination plant outfalls. Copyright © 2016 Elsevier Ltd. All rights reserved.

  7. Relative potency estimation for synthetic petroleum skin carcinogens.

    OpenAIRE

    Holland, J M; Wolf, D A; Clark, B R

    1981-01-01

    A procedure for quantitative analysis of skin carcinogenesis data, for the purpose of establishing carcinogenic potency, has been applied to observations obtained from C3H mice exposed continuously to synthetic and natural petroleums. The importance of total polynuclear aromatic (PNA) content to the skin carcinogenic activity of the crude materials was also examined. Of three synthetic petroleums evaluated, all were shown capable of inducing skin neoplasms within a two-year exposure period. U...

  8. Water quality in the vicinity of Mosquito Creek Lake, Trumbull County, Ohio, in relation of the chemistry of locally occurring oil, natural gas, and brine

    International Nuclear Information System (INIS)

    Barton, G.J.; Burruss, R.C.; Ryder, R.T.

    1998-01-01

    The purpose of this report is to describe current water quality and the chemistry of oil, natural gas, and brine in the Mosquito Creek Lake area. Additionally, these data are used to characterize water quality in the Mosquito Creek Lake area in relation to past oil and natural gas well drilling and production. To meet the overall objective, several goals for this investigation were established. These include (1) collect water-quality and subsurface-gas data from shallow sediments and rock that can be used for future evaluation of possible effects of oil and natural gas well drilling and production on water supplies, (2) characterize current surface-water and ground-water quality as it relates to the natural occurrence and (or) release of oil, gas, and brine (3) sample and chemically characterize the oil in the shallow Mecca Oil Pool, gas from the Berea and Cussewago Sandstone aquifers, and the oil, gas, and brine from the Clinton sandstone, and (4) identify areas where aquifers are vulnerable to contamination from surface spills at oil and natural gas drilling and production sites

  9. Effects of brine migration on waste storage systems. Final report

    International Nuclear Information System (INIS)

    Gaffney, E.S.; Nickell, R.E.

    1979-01-01

    Processes which can lead to mobilization of brine adjacent to spent fuel or nuclear waste canisters and some of the thermomechanical consequences have been investigated. Velocities as high as 4 x 10 -7 m s -1 (13 m y -1 ) are calculated at the salt/canister boundary. As much as 40 liters of pure NaCl brine could accumulate around each canister during a 10-year storage period. Accumulations of bittern brines would probably be less, in the range of 2 to 5 liters. With 0.5% water, NaCl brine accumulation over a 10-year storage cycle around a spent fuel canister producing 0.6 kW of heat is expected to be less than 1 liter for centimeter-size inclusions and less than 0.5 liter for millimeter-size inclusions. For bittern brines, about 25 years would be required to accumulate 0.4 liter. The most serious mechanical consequence of brine migration would be the increased mobility of the waste canister due to pressure solution. In pressure solution enhanced deformation, the existence of a thin film of fluid either between grains or between media (such as between a canister and the salt) provides a pathway by which the salt can be redistributed leading to a marked increase in strain rates in wet rock relative to dry rock. In salt, intergranular water will probably form discontinuous layers rather than films so that they would dominate pressure solution. A mathematical model of pressure solution indicates that pressure solution will not lead to appreciable canister motions except possibly in fine grained rocks (less than 10 -4 m). In fine grained salts, details of the contact surface between the canister and the salt bed may lead to large pressure solution motions. A numerical model indicates that heat transfer in the brine layer surrounding a spent fuel canister is not conduction dominated but has a significant convective component

  10. Fact sheet. Norwegian petroleum activity 1995

    International Nuclear Information System (INIS)

    Harv, M.R.

    1995-02-01

    This report on the Norwegian petroleum activity in 1994 is published by the Royal Ministry of Industry and Energy. Production to the end of 1994 totaled 1.63 billion scm oe. At 31 Dec 1994, total reserves on the Norwegian continental shelf comprised 1.34 billion scm oe of oil, 1.35 billion scm oe of gas and 0.1 billion scm oe of NGLs. The net increment in oil and gas during 1994 was about 115 million scm oe. Twenty-seven exploration wells, including 22 wildcats and five appraisal wells, were completed or temporarily abandoned on the Norwegian continental shelf in 1994. Governmental approval was given for developing the second phase of the Ekofisk field, the Vigdis and Snorre Lunde oil fields, and two smaller formations on the Veslefrikk field. Investment in petroleum operations totaled about NOK 50 billion. Norwegian oil and gas production came to about 180 million scm oe. At present levels of output, Norway's petroleum resources are sufficient to support production of oil for 20 years and of gas for 115 years. The estimated value of Norwegian petroleum exports in 1994 is NOK 114 billion, representing about 34% of the country's total export earnings. State revenues from taxes and royalties on petroleum operations came to about NOK 23.7 billion, or eight per cent of total government revenues. 24 figs., 13 tabs

  11. The Brine Sampling and Evaluation Program (PSEP) at WIPP

    International Nuclear Information System (INIS)

    Deal, D.E.; Roggenthen, W.M.

    1989-01-01

    The Permian salt beds of the WIPP facility are virtually dry. The amount of water present in the rocks exposed in the excavations that is free to migrate under pressure gradients was estimated by heating salt samples to 95 degrees C and measuring weight loss. Clear balite contains about 0.22 weight percent water and the more argillaceous units average about 0.75 percent. Measurements made since 1984 as part of the Brine Sampling and Evaluation Program (BSEP) indicate that small amounts of this brine can migrate into the excavations and does accumulate in the underground environment. Brine seepage into drillholes monitored since thy were drilled show that brine seepage decreases with time and that many have dried up entirely. Weeping of brine from the walls of the repository excavations also decreases after two or more years. Chemical analyses of brines shows that they are sodium-chloride saturated and magnesium-rich

  12. Choice of optimal working fluid for binary power plants at extremely low temperature brine

    Science.gov (United States)

    Tomarov, G. V.; Shipkov, A. A.; Sorokina, E. V.

    2016-12-01

    The geothermal energy development problems based on using binary power plants utilizing lowpotential geothermal resources are considered. It is shown that one of the possible ways of increasing the efficiency of heat utilization of geothermal brine in a wide temperature range is the use of multistage power systems with series-connected binary power plants based on incremental primary energy conversion. Some practically significant results of design-analytical investigations of physicochemical properties of various organic substances and their influence on the main parameters of the flowsheet and the technical and operational characteristics of heat-mechanical and heat-exchange equipment for binary power plant operating on extremely-low temperature geothermal brine (70°C) are presented. The calculation results of geothermal brine specific flow rate, capacity (net), and other operation characteristics of binary power plants with the capacity of 2.5 MW at using various organic substances are a practical interest. It is shown that the working fluid selection significantly influences on the parameters of the flowsheet and the operational characteristics of the binary power plant, and the problem of selection of working fluid is in the search for compromise based on the priorities in the field of efficiency, safety, and ecology criteria of a binary power plant. It is proposed in the investigations on the working fluid selection of the binary plant to use the plotting method of multiaxis complex diagrams of relative parameters and characteristic of binary power plants. Some examples of plotting and analyzing these diagrams intended to choose the working fluid provided that the efficiency of geothermal brine is taken as main priority.

  13. Stratification and space-time variability of Red Sea hot brines

    Energy Technology Data Exchange (ETDEWEB)

    Monin, A S; Plakhin, E A

    1982-11-01

    The results of hydrophysical studies in Red Sea hot brines prefaced with historical information are presented. The CTD-recorder readings show stratification of the upper brine in the Atlantis II Deep into meter-scale layers, in agreement with laboratory findings. Repeated soundings with the AIST CTD meter of the upper brine interface in the Valdivia Deep recorded internal waves of 3 to 4-h periods. The observations show the different nature of brines in the four deeps studied and the lack of contact between the brine layers of the Chain and Discovery deeps.

  14. Petroleum and gas economy in Arab Countries, in Angola, Congo and Nigeria

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    This paper gives informations on petroleum and natural gas industry, petroleum market and prices, trade and contracts, exploration and production. In OPEC countries, petroleum production has increased of 1% at a level of 24.77 millions barrels per day. Petroleum exploration or oil field development are going on at Ras al Khaima and Oum al Qaiwain (Arab Union Emirates), Gachsaran and Parsi (Iran) and Masilia (Yemen). In Tunisia, Union Texas Petroleum (Houston) has obtained a license for the exploration of Ramla oil field. In 1993, for the first, world wide petroleum demand will be reduce of 150000 barrels per day since 1983. In Congo, Sofresid Petrole Gaz has obtained a contract for the building of the bridge of two offshore platforms on N'Kossa oil field. In Nigeria, Offshore Pipelines Inc. (Houston) will build offshore structures for North Apoi and Okubie oil fields

  15. Radioactive waste isolation in salt: geochemistry of brine in rock salt in temperature gradients and gamma-radiation fields - a selective annotated bibliography

    International Nuclear Information System (INIS)

    Hull, A.B.; Williams, L.B.

    1985-07-01

    Evaluation of the extensive research concerning brine geochemistry and transport is critically important to successful exploitation of a salt formation for isolating high-level radioactive waste. This annotated bibliography has been compiled from documents considered to provide classic background material on the interactions between brine and rock salt, as well as the most important results from more recent research. Each summary elucidates the information or data most pertinent to situations encountered in siting, constructing, and operating a mined repository in salt for high-level radioactive waste. The research topics covered include the basic geology, depositional environment, mineralogy, and structure of evaporite and domal salts, as well as fluid inclusions, brine chemistry, thermal and gamma-radiation effects, radionuclide migration, and thermodynamic properties of salts and brines. 4 figs., 6 tabs

  16. Radioactive waste isolation in salt: geochemistry of brine in rock salt in temperature gradients and gamma-radiation fields - a selective annotated bibliography

    Energy Technology Data Exchange (ETDEWEB)

    Hull, A.B.; Williams, L.B.

    1985-07-01

    Evaluation of the extensive research concerning brine geochemistry and transport is critically important to successful exploitation of a salt formation for isolating high-level radioactive waste. This annotated bibliography has been compiled from documents considered to provide classic background material on the interactions between brine and rock salt, as well as the most important results from more recent research. Each summary elucidates the information or data most pertinent to situations encountered in siting, constructing, and operating a mined repository in salt for high-level radioactive waste. The research topics covered include the basic geology, depositional environment, mineralogy, and structure of evaporite and domal salts, as well as fluid inclusions, brine chemistry, thermal and gamma-radiation effects, radionuclide migration, and thermodynamic properties of salts and brines. 4 figs., 6 tabs.

  17. Zooplankton at deep Red Sea brine pools

    KAUST Repository

    Kaartvedt, Stein

    2016-03-02

    The deep-sea anoxic brines of the Red Sea comprise unique, complex and extreme habitats. These environments are too harsh for metazoans, while the brine–seawater interface harbors dense microbial populations. We investigated the adjacent pelagic fauna at two brine pools using net tows, video records from a remotely operated vehicle and submerged echosounders. Waters just above the brine pool of Atlantis II Deep (2000 m depth) appeared depleted of macrofauna. In contrast, the fauna appeared to be enriched at the Kebrit Deep brine–seawater interface (1466 m).

  18. An Integrated Capillary, Buoyancy, and Viscous-Driven Model for Brine/CO2Relative Permeability in a Compositional and Parallel Reservoir Simulator

    KAUST Repository

    Kong, X.; Delshad, M.; Wheeler, M. F.

    2012-01-01

    The effectiveness of CO2 storage in the saline aquifers is governed by the interplay of capillary, viscous, and buoyancy forces. Recent experimental study reveals the impact of pressure, temperature, and salinity on interfacial tension (IFT) between CO2 and brine. The dependence of CO2-brine relative permeability and capillary pressure on pressure (IFT) is also clearly evident in published experimental results. Improved understanding of the mechanisms that control the migration and trapping of CO2 in subsurface is crucial to design future storage projects that warrant long-term and safe containment. Simulation studies ignoring the buoyancy and also variation in interfacial tension and the effect on the petrophysical properties such as trapped CO2 saturations, relative permeability, and capillary pressure have a poor chance of making accurate predictions of CO2 injectivity and plume migration. We have developed and implemented a general relative permeability model that combines effects of pressure gradient, buoyancy, and IFT in an equation of state (EOS) compositional and parallel simulator. The significance of IFT variations on CO2 migration and trapping is assessed.

  19. An Integrated Capillary, Buoyancy, and Viscous-Driven Model for Brine/CO2Relative Permeability in a Compositional and Parallel Reservoir Simulator

    KAUST Repository

    Kong, X.

    2012-11-03

    The effectiveness of CO2 storage in the saline aquifers is governed by the interplay of capillary, viscous, and buoyancy forces. Recent experimental study reveals the impact of pressure, temperature, and salinity on interfacial tension (IFT) between CO2 and brine. The dependence of CO2-brine relative permeability and capillary pressure on pressure (IFT) is also clearly evident in published experimental results. Improved understanding of the mechanisms that control the migration and trapping of CO2 in subsurface is crucial to design future storage projects that warrant long-term and safe containment. Simulation studies ignoring the buoyancy and also variation in interfacial tension and the effect on the petrophysical properties such as trapped CO2 saturations, relative permeability, and capillary pressure have a poor chance of making accurate predictions of CO2 injectivity and plume migration. We have developed and implemented a general relative permeability model that combines effects of pressure gradient, buoyancy, and IFT in an equation of state (EOS) compositional and parallel simulator. The significance of IFT variations on CO2 migration and trapping is assessed.

  20. Assessment of Brine Management for Geologic Carbon Sequestration

    Energy Technology Data Exchange (ETDEWEB)

    Breunig, Hanna M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Birkholzer, Jens T. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Borgia, Andrea [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Price, Phillip N. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Oldenburg, Curtis M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; McKone, Thomas E. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division

    2013-06-13

    surface water bodies. Results of the assessment were generated, stored, and analyzed using Microsoft Excel spreadsheets and ESRI Geographical Information System (GIS) maps. Conclusions about the relative benefits and impacts of alternative brine-­management strategies were highly sensitive to local climate and weather, and aquifer water chemistry. The NPV of certain scenarios ranged from -­$50/mt-­CO2 (a cost) to +$10/mt-­CO2 (revenue). The land footprint of the scenarios in this study ranged from <1 km2 to 100 km2. Brine extraction as a pressure management tool for GCS has potential for improving the economics and for minimizing the environmental impacts of CCS. In order to maximize this potential, careful analysis of each saline aquifer and region must be conducted to determine a regionally appropriate brine use sequence (BUS) at the time of site selection. Models that use GIS will be essential tools in determining such sequences for individual CFPP. Future studies that perform risk and life cycle assessments (LCA) of BUS scenarios, incorporate additional impact metrics into the BUS model, and enhance the temporal sensitivity of the model would improve the robustness of this regional assessment method.

  1. Offshore oceanographic and environmental monitoring services for the Strategic Petroleum Reserve. Volume I. Appendices. Annual report for the Bryan Mound Site, September 1982-August 1983

    Energy Technology Data Exchange (ETDEWEB)

    None

    1984-03-01

    The Department of Energy's Strategic Petroleum Reserve Program began leaching the Bryan Mound salt dome and discharging brine into the coastal waters offshore of Freeport, Texas on March 10, 1980. This report describes the findings of a team of Texas A and M University scientists and engineers who have conducted a study to evaluate the effects of the Bryan Mound brine discharge on the marine environment. The study addresses the areas of physical oceanography, analysis of the discharge plume, water and sediment quality, nekton, benthos and data management. It focuses on the period from September 1982 through August 1983. The ambient physical environment and its temporal and spatial variability were studied by means of continuously recording in situ current/conductivitiy/temperature meters and twelve, one-day synoptic hydrographic cruises. The quarterly water and sediment quality data show a small increase in salinity, sodium and chloride ions occurs in the bottom waters and sediment pore waters near the diffuser relative to those values measured at stations farther away. Data from the brine plume study for this reporting study show the largest areal extent within the +1 o/oo above ambient salinity contour was 40.0 km/sup 2/ which occurred on August 11, 1983. It appears that brine disposal at Bryan Mound has had neglible if any influence on the nekton community surrounding the diffuser. The benthic quarterly data from 26 stations, including 7 collections made after the diffuser outflow rate was increased to 1,000,000 barrels/day, show the total numbers of species at the diffuser station were higher than most other nearfield stations as well as many farfield stations in both the pre- and post-1,000,000 barrels/day brine flow periods. 138 references, 175 figures, 53 tables.

  2. Liquid interfacial water and brines in the upper surface of Mars

    Science.gov (United States)

    Moehlmann, Diedrich

    2013-04-01

    Liquid interfacial water and brines in the upper surface of Mars Diedrich T.F. Möhlmann DLR Institut für Planetenforschung, Rutherfordstr. 2, D - 12489 Berlin, Germany dirk.moehlmann@dlr.de Interfacial water films and numerous brines are known to remain liquid at temperatures far below 0° C. The physical processes behind are described in some detail. Deliquescence, i.e. the liquefaction of hygroscopic salts at the threshold of a specific "Deliquescence Relative Humidity", is shown to be that process, which on present Mars supports the formation of stable interfacial water and bulk liquids in form of temporary brines on and in a salty upper surface of present Mars in a diurnally temporary and repetitive process. Temperature and relative humidity are the governing conditions for deliquescence (and the counterpart "efflorescence") to evolve. The current thermo-dynamical conditions on Mars support these processes to evolve on present Mars. The deliquescence-driven presence of liquid brines in the soil of the upper surface of Mars can expected to be followed by physical and chemical processes like "surface cementation", down-slope flows, and physical and chemical weathering processes. A remarkable and possibly also biologically relevant evolution towards internally interfacial water bearing structures of dendritic capillaries is related to their freezing - thawing driven formation. The internal walls of these network-pores or -tubes can be covered by films of interfacial water, providing that way possibly habitable crack-systems in soil and rock. These evolutionary processes of networks, driven by their tip-growth, can expected to be ongoing also at present.

  3. Uranium-thorium series radionuclides in brines and reservoir rocks from two deep geothermal boreholes in the Salton Sea geothermal field, southeastern California

    International Nuclear Information System (INIS)

    Zukin, J.G.; Hammond, D.E.; Ku, Tehlung; Elders, W.A.

    1987-01-01

    Naturally occurring U and Th series radionuclides have been analyzed in high temperature brines (∼ 300 degree C, 25 wt% dissolved solids) and associated rocks from two deep geothermal wells located on the northeastern margin of the Salton Sea Geothermal Field (SSGF). These data are part of a study of the SSGF as a natural analog of possible radionuclide behavior near a nuclear waste repository constructed in salt beds, and permit evaluation of some characteristics of water-rock interaction in the SSGF

  4. Petroleum and mineral resources of Antarctica

    Science.gov (United States)

    Kovar, Karel; Behrendt, John Charles

    1983-01-01

    No known petroleum or mineral resources occur in Antarctica. The data on these subjects have been collected, mainly since the IGY (International Geophysical Year), 1957-58, as a part of other research carried out by geologists and geophysicists from a number of countries. Specific resource-related studies have not been made. Wright and Williams (1974) summarized what was known of Antarctic mineral resources a decade ago.The U.S. Geological Survey has been actively pursuing various investigations in Antarctica since 194 7. In the course of this work and that of our colleagues elsewhere in the United States and in other countries, much information relevant to petroleum and mineral resources has been obtained. Since 1976, modern state-of-the-art multichannel seismic reflection and aeromagnetic surveys by several countries over the continental margin of Antarctica have indicated thick sedimentary basins. However, no offshore drilling beneath the continental shelf has taken place since the DSDP (Deep Sea Drilling Project) holes in the Ross Sea in 1973. Geologic field investigations begun at the turn of the twentieth century have been intensified in the past two decades; most rock outcrops have been visited and samples collected. Technology to exploit resources, particularly in the Arctic, has been developing at a rapid rate, and much of it could be applied to Antarctica. As a result of the petroleum price increases of the past decade, the attention of a number of countries has turned to Antarctica, but under the policy of "voluntary restraint" adopted by the Antarctic Treaty nations, no active petroleum or mineral exploration is taking place. The Antarctic treaty countries are in the process of negotiating an Antarctic mineral resources regime that is anticipated to be completed within the next several years. Therefore it seemed timely to us to readdress the question of petroleum and mineral resources. These reports review and summarize the available information. The

  5. Petroleum Biotechnology. Developments and Perspectives

    International Nuclear Information System (INIS)

    Vazquez-Duhalt, R.; Quintero-Ramirez, R.

    2004-01-01

    This book deals with the field of petroleum biorefining and biological upgrade of petroleum; it presents a critical review as well as an integrated overview of the potential biochemical processes, bridging the gap between academia and industry. It addresses today's demanding production challenges, taking into account energy efficient and environmentally friendly processes, and also looks at the future possibility of implementing new refinery systems

  6. OUT Success Stories: Chemical Treatments for Geothermal Brines

    International Nuclear Information System (INIS)

    Burr, R.

    2000-01-01

    DOE research helped develop the large, untapped geothermal resource beneath the Salton Sea in California's Imperial Valley. The very hot brines under high pressure make them excellent for electric power production. The brines are very corrosive and contain high concentrations of dissolved silica. DOE worked with San Diego Gas and Electric Company to find a solution to the silica-scaling problem. This innovative brine treatment eliminated scaling and made possible the development of the Salton Sea geothermal resource

  7. Sorption of cesium and strontium from concentrated brines by backfill barrier materials

    International Nuclear Information System (INIS)

    Winslow, C.D.

    1981-03-01

    The sorption of radionuclides from potentially intruding groundwater at a nuclear waste repository is a major chemical function of backfill barriers. In this study, various materials (including clays, zeolites and an inorganic ion exchanger) were screened for the sorption of the fission products cesium and strontium in concentrated brines. Representative brines A and B for the Waste Isolation Pilot Plant (WIPP), a proposed radioactive waste repository and test facility in bedded salt were used. Sorption properties were quantified using empirical distribution coefficients, k/sub d/. Of the materials examined, sodium titanate had the highest k/sub d/ for the sorption of Sr(II) in both brine A (k/sub d/ = 125 ml/g) and brine B(k/sub d/ = 500 to 600 ml/g). A mordenite-type zeolite was the most effective getter for Cs(I) in brine A (k/sub d = 27 ml/g), while illite yielded the highest k/sub d/ for Cs(I) in brine B (k/sub d/ = 115 ml/g). The relative merit of these k/sub d/ values is evaluated in terms of calculated estimates of breakthrough times for a backfill barrier containing the getter. Results show that a backfill mixture containing these getters is potentially an effective barrier to the migration of Sr(II) and Cs(I), although further study (especially for the sorption of cesium from brine A) is recommended. Initial mechanistic studies revealed competing ion effects which would support an ion exchange mechanism. K/sub d/'s were constant over a Sr(II) concentration range of 10 -11 to 10 -5 M and a Cs(I) concentration range of 10 -8 to 10 -5 M, supporting the choice of a linear sorption isotherm as a model for the results. Constant batch composition was shown to be attained within one week

  8. Brine contamination to aquatic resources from oil and gas development in the Williston Basin, United States

    Science.gov (United States)

    Gleason, Robert A.; Contributions by Chesley-Preston, Tara L.; Coleman, James L.; Haines, Seth S.; Jenni, Karen E.; Nieman, Timothy L.; Peterman, Zell E.; van der Burg, Max Post; Preston, Todd M.; Smith, Bruce D.; Tangen, Brian A.; Thamke, Joanna N.; Gleason, Robert A.; Tangen, Brian A.

    2014-01-01

    The Williston Basin, which includes parts of Montana, North Dakota, and South Dakota in the United States and the provinces of Manitoba and Saskatchewan in Canada, has been a leading domestic oil and gas producing region for more than one-half a century. Currently, there are renewed efforts to develop oil and gas resources from deep geologic formations, spurred by advances in recovery technologies and economic incentives associated with the price of oil. Domestic oil and gas production has many economic benefits and provides a means for the United States to fulfill a part of domestic energy demands; however, environmental hazards can be associated with this type of energy production in the Williston Basin, particularly to aquatic resources (surface water and shallow groundwater) by extremely saline water, or brine, which is produced with oil and gas. The primary source of concern is the migration of brine from buried reserve pits that were used to store produced water during recovery operations; however, there also are considerable risks of brine release from pipeline failures, poor infrastructure construction, and flow-back water from hydraulic fracturing associated with modern oilfield operations. During 2008, a multidisciplinary (biology, geology, water) team of U.S. Geological Survey researchers was assembled to investigate potential energy production effects in the Williston Basin. Researchers from the U.S. Geological Survey participated in field tours and met with representatives from county, State, tribal, and Federal agencies to identify information needs and focus research objectives. Common questions from agency personnel, especially those from the U.S. Fish and Wildlife Service, were “are the brine plumes (plumes of brine-contaminated groundwater) from abandoned oil wells affecting wetlands on Waterfowl Production Areas and National Wildlife Refuges?” and “are newer wells related to Bakken and Three Forks development different than the older

  9. Logistics aspects of petroleum pipeline operations

    Directory of Open Access Journals (Sweden)

    W. J. Pienaar

    2010-11-01

    Full Text Available The paper identifies, assesses and describes the logistics aspects of the commercial operation of petroleum pipelines. The nature of petroleum-product supply chains, in which pipelines play a role, is outlined and the types of petroleum pipeline systems are described. An outline is presented of the nature of the logistics activities of petroleum pipeline operations. The reasons for the cost efficiency of petroleum pipeline operations are given. The relative modal service effectiveness of petroleum pipeline transport, based on the most pertinent service performance measures, is offered. The segments in the petroleum-products supply chain where pipelines can play an efficient and effective role are identified.

  10. Effect of iron cation on geochemical trapping of CO2 in brine

    Science.gov (United States)

    Liu, Qi; Maroto-Valer, Mercedes

    2014-05-01

    Carbon dioxide sequestration using brines has emerged as a promising technology to mitigate the adverse impacts of climate change due to its large storage capacity and favorable chemistries. However, the permanent storage (mineral trapping) of CO2 in brines takes significantly long periods of time as the formation and precipitation of carbonates is very slow .[1]. The main parameters reported to effect on mineral trapping of CO2 sequestration in brines are brine composition, brine pH, system temperature and pressure.[2, 3]. It is suggested that the precipitation of mineral carbonates is mostly dependent on brine pH. Previous studies by the authors concluded that iron in natural brines causes pH instability, but it was not ascertained whether ferric iron or ferrous iron caused pH instability .[4]. Accordingly, the aim of this project is to study synthetic brines mimicking the major ions found in natural brines and including different concentrations of ferric and ferrous iron. Three brines were prepared, as follows: Brine 1 was prepared with ferric Fe3+ iron, Brine 2 prepared with ferrous Fe2+ iron and Brine 3 prepared with no iron. A series of pH stability studies and carbonation reactions were conducted using the above three brines. It is concluded that the ferrous iron causes pH instability, while ferric iron might promote carbonate precipitation. .1. Garcia, S., et al., Sequestration of non-pure carbon dioxide streams in iron oxyhydroxide-containing saline repositories. International Journal of Greenhouse Gas Control, 2012. 7: p. 89-97. 2. Liu, Q. and M.M. Maroto-Valer, Investigation of the pH effect of a typical host rock and buffer solution on CO 2 sequestration in synthetic brines. Fuel Processing Technology, 2010. 91(10): p. 1321-1329. 3. Liu, Q. and M.M. MarotoValer, Parameters affecting mineral trapping of CO2 sequestration in brines. Greenhouse Gases: Science and Technology, 2011. 1(3): p. 211-222. 4. Druckenmiller, M.L. and M.M. Maroto-Valer, Carbon

  11. Catalysts in petroleum refining and petrochemical industries 1995

    Energy Technology Data Exchange (ETDEWEB)

    Absi-Halabi, M.; Beshara, J.; Qabazard, H.; Stanislaus, A. [eds.] [Petroleum, Petrochemicals and Materials Division, Kuwait Institute of Scientific Research, Kuwait (Kuwait)

    1996-07-01

    Catalysis plays an increasingly critical role in modern petroleum refining and basic petrochemical industries. The market demands for and specifications of petroleum and petrochemical products are continuously changing. They have impacted the industry significantly over the past twenty years. Numerous new refining processes have been developed and significant improvements were made on existing technologies. Catalysts have been instrumental in enabling the industry to meet the continuous challenges posed by the market. As we enter the 21st century, new challenges for catalysis science and technology are anticipated in almost every field. Particularly, better utilization of petroleum resources and demands for cleaner transportation fuels are major items on the agenda. It is against this background that the 2nd International Conference on Catalysts in Petroleum Refining and Petrochemical Industries was organized. The papers from the conference were carefully selected from around 100 submissions. They were a mix of reviews providing an overview of selected areas, original fundamental research results, and industrial experiences. The papers in the proceedings were grouped in the following sections for quick reference: Plenary Papers; Hydroprocessing of Petroleum Residues and Distillates; Fluid Catalytic Cracking; Oxidation Catalysis; Aromatization and Polymerization Catalysis; Catalyst Characterization and Performance. The plenary papers were mostly reviews covering important topics related to the objectives of the conference. The remaining sections cover various topics of major impact on modern petroleum refining and petrochemical industries. A large number of papers dealt with hydroprocessing of petroleum distillates and residues which reflects the concern over meeting future sulfur-level specifications for diesel and fuel oils

  12. Industry consequences of reduced petroleum activity; Naeringsmessige konsekvenser av redusert petroleumsaktivitet

    Energy Technology Data Exchange (ETDEWEB)

    2010-10-22

    Norwegian oil production is falling. Top of the petroleum production was reached in 2004, and in line with forecasts from the Norwegian Petroleum Directorate and Econ Poeyry (2009), we anticipate a continued decline in production towards an end around 2080. Petroleum industries accounted for about a quarter of Norwegian value creation in 2008. The industries provide strong growth impetus to the Norwegian economy through investments in new fields and operation of existing ones. The petroleum activity on the Norwegian shelf add to our estimates, the basis for about 90 000 jobs in the petroleum industry and the supplier industry. The prescribed reduction in Norwegian petroleum activities will naturally reduce petroleum-related employment. We calculate in this report the effect of a reduction in the petroleum activity with regard to employment. The calculations show a strong decline in employment in the period 2025-2080. In order to reduce the effects of the fall, the Norwegian authorities can open more areas for petroleum production. We show in this report the employment consequences of an opening of the areas off Lofoten, Vesteraalen and Senja may have for employment. To calculate the employment effects are based on an estimate of 2 billion barrels of oil equivalent (boe), and assuming that it made more commercial discoveries. This estimate lies between the updated estimate of Petroleum Directorate announced 16 April 2010 and the projection industry refers to. Our estimate of 2 billion barrels is based on continued technological advances that increase the recovery rate. Based on an estimate of 2 billion barrels, our calculations show that this can lay the basis for between 3000 and 8000 permanent jobs in the petroleum industry and supplier industry. We do not know today whether it is or how much petroleum resources in the areas concerned. If there is no commercial discoveries, employment effect will only be related to exploration activity. If however, there are more

  13. Brine transport studies in the bedded salt of the Waste Isolation Pilot Plant (WIPP)

    International Nuclear Information System (INIS)

    McTigue, D.F.; Nowak, E.J.

    1987-01-01

    Brine flow has been measured to unheated boreholes for periods of a few days and to heated holes for two years in the WIPP facility. It is suggested that Darcy flow may dominate the observed influx of brine. Exact solutions to a linearized model for one-dimensional, radial flow are evaluated for conditions approximating the field experiments. Flow rates of the correct order of magnitude are calculated for permeabilities in the range 10 -21 to 10 -20 m 2 (1 to 10 nanodarcy) for both the unheated and heated cases. 20 refs., 3 figs., 1 tab

  14. Biological screening of chitosan derivatives using Artemia spp. (brine shrimp test)

    International Nuclear Information System (INIS)

    Rozaini Mohd Zohdi; Norimah Yusof; Asnah Hassan

    2006-01-01

    The present study reported on the screening of six selected chitosan derivatives using the brine shrimp lethality bioassay. In addition, the irradiation effects towards the compounds at 25 kGy were also studied. Chitosan is a natural polysaccharide derived from chitin, extracted from the exoskeletons of crustaceans and insects as well as walls of some bacteria and fungi. Brine shrimp test is employed for the screening of toxicity of chitosan derivatives. Toxicity test was carried out by adding different concentrations of tested samples to approximately 5 to 15 Artemia salina larvae. Biological activity using the brine shrimp bioassay was recorded as LC 50 i.e. lethal concentration that kills 50% of the larvae within 24 hours of contact with the samples. Compounds are considered toxic when the LC 50 value is lower than 1 mg/ml by brine shrimp bioassay and practically non-toxic when the value is larger. Of the samples tested, none were toxic to the brine shrimp (LC 50 > 1 mg/ml). The LC 50 values of all chitosan derivatives tested, control and irradiated at 25 kGy were above 1 mg/ml thus all tested samples are considered non-toxic. This study demonstrated that irradiation at 25 kGy showed no significant effects towards the toxicity of the chitosan derivatives. After irradiation, only NO-CMC exhibited marked decrease in LC 50 value, reduced by 3-fold from 34.96 mg/ml to 11.07 mg/ml while O-CMC (5.45 mg/ml to 5 mg/ml) showed no clear differences based on rough estimation. This study suggested that brine shrimp bioassay is a simple, reliable and convenient method that could provide useful clues of the relative toxic potential of the sample tested. (Author)

  15. Evaluation of brine disposal from the Bryan Mound site of the Strategic Petroleum Reserve Program. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hann, R.W. Jr.; Randall, R.E. (eds.)

    1980-12-01

    The purpose of this report is to describe the environmental conditions found by the principal investigators during the predisposal study conducted from September 1977 through February 1980 prior to the start of brine discharge in March 1980. The major areas of investigation are physical oceanography, analysis of the discharge plume, water and sediment quality, nekton, benthos, phytoplankton, zooplankton, and data management. Volume 1 describes the results of the predisposal study, and it is divided into eight chapters entitled: Physical Oceanography, Analysis of the Discharge Plume, Water and Sediment Quality, Nekton, Benthos, Zooplankton, Phytoplankton, and Data Management. Volume 2 consists of appendices which contain additional supporting data in the form of figures and tables.

  16. Migration rates of brine inclusions in single crystals of NaCl

    International Nuclear Information System (INIS)

    Chou, I.M.

    1982-01-01

    Rock-salt deposits have been considered as a possible medium for the permanent storage of high-level radioactive wastes and spent fuel. Brine inclusions present in natural salt can migrate toward the waste if the temperature and the temperature gradients in the vicinity of the radioactive waste are large enough. This migration is due to the dissolution of salt at the hot side of the salt-brine interface, ion diffusion through the brine droplet, and the precipitation of salt at the cold side of the salt brine interface. In order to quantify the problem, the migration rate of these brine inclusions must be estimated under various repository conditions. This paper estimates migration rates for all-liquid brine inclusions in single crystals of NaCl by utilizing recent data for brines and the model of Anthony and Cline [T.R. Anthony and H.E. Cline, J. Appl. Phys., 42, pp. 3380-387 (1971)]. The predictions are compared with experimentally measured migration rates. 4 figures, 6 tables

  17. Natural gas in 1936: Petroleum in 1936: The gas and oil fields in the Guelph and Medina (Grimsby) formations: Appendix, the Brownsville Gas Field: Gas and oil in eastern Ontario. Annual publication

    Energy Technology Data Exchange (ETDEWEB)

    Harkness, R B; Evans, C S

    1938-12-31

    Part V of this annual report consists of four separate reports: Natural gas, petroleum, gas and oil fields in the Guelph and Medina (Grimsby) formations, and gas and oil in eastern Ontario. The natural gas report discusses production and distribution; changes and improvements; consumption and rates; gas wells and their production; and licenses issued. The logs of wells are also included, being presented alphabetically by counties, townships, and owners, respectively. The petroleum report presents information on production and drilling by township; expansion; and petroleum importation and refining operations.

  18. Thermal-gradient migration of brine inclusions in salt

    International Nuclear Information System (INIS)

    Yagnik, S.K.

    1982-02-01

    It has been proposed that the high level nuclear waste be buried deep underground in a suitable geologic formation. Natural salt deposits have been under active consideration as one of the geologic formations where a nuclear waste repository may be built in future. The salt deposits, however, are known to contain a small amount (about 0.5 vol.%) of water in the form of brine inclusions which are dispersed throughout the medium. The temperature gradients imposed by the heat generating nuclear waste will mobilize these brine inclusions. It is important to know the rate and the amount of brine accumulating at the waste packages to properly evaluate the performance of a nuclear waste repository. An extensive experimental investigation of the migration velocities of brine inclusions in synthetic single crystals of NaCl and in polycrystalline natural salt crystals has been conducted. The results show that in a salt repository the brine inclusions within a grain would move with the diffusion controlled velocities. The brine reaching a grain boundary may be swept across, if the thermal gradient is high enough. Grain boundaries in polycrystalline rock salt are apparently quite weak and open up due to drilling the hole for a waste canister and to the thermal stresses which accompany the thermal gradient produced by the heat generating waste. The enhanced porosity allows the water reaching the grain boundary to escape by a vapor transport process

  19. Canada-Nova Scotia Offshore Petroleum Board annual report, 1992-1993

    International Nuclear Information System (INIS)

    1993-06-01

    The Canada-Nova Scotia Offshore Petroleum Board was established as the agency responsible for the regulation of the hydrocarbon resources in the Nova Scotia offshore. The Board evaluates resource potential, administers petroleum exploration and production rights, approves offshore activities, and approves benefits and development plans. The main activities of the Board in 1992-1993 are summarized and financial statements are presented. Highlights include production of 572,300 m 3 of oil during the first production season of LASMO Nova Scotia Ltd.'s Cohasset development, the first commercial offshore oil production for Canada; four major resource evaluation projects in the Glenelg Field, the Laurentian sub-basin, the Fundy Rift Basin, and the Panuke Field; holding of discussions between Nova Scotia, Newfoundland, and Canada on the maritime boundary lines between respective offshore petroleum board jurisdictions, in the wake of a June 1992 determination of the disputed maritime boundary around St. Pierre et Miquelon; and amendments of certain safety-related legislation applicable to offshore operations. Employment benefits of the Cohasset project during 1992 totalled ca 470 Nova Scotians and 120 other Canadians. 3 tabs

  20. Brine transport in porous media self-similar solutions

    NARCIS (Netherlands)

    C.J. van Duijn (Hans); L.A. Peletier (Bert); R.J. Schotting (Ruud)

    1996-01-01

    textabstractIn this paper we analyze a model for brine transport in porous media, which includes a mass balance for the fluid, a mass balance for salt, Darcy's law and an equation of state, which relates the fluid density to the salt mass fraction. This model incorporates the effect of local volume

  1. Petroleum-related contaminants near a produced water discharge site in the Santa Barbara Channel

    International Nuclear Information System (INIS)

    Jones, A.D.; Witter, A.E.; Higashi, R.M.

    1994-01-01

    Offshore oil production generates substantial quantities of waste water that is frequently discharged into marine waters. Contamination of coastal sediments occurs due to other inputs including natural petroleum seeps, and this complicates assessments of the environmental effects of produced water in marine ecosystems. The current study has focused on characterization of contaminants in sediments near produced water discharge site off the coast of Southern California. First, it was important to address the question: ''What contaminants in sediments should be monitored as indicators of produced water effects?'' Dichloromethane extracts of sediments were analyzed for numerous organic constituents using gas chromatography-mass spectrometry and selected ion monitoring. Though the phenols and fatty acids were not detected in sediment extracts, normal and branched alkanes and other petroleum hydrocarbon biomarkers were quantified. No relationship was evident that related absolute concentrations of organic compounds to distance from the outfall, but patterns of petroleum hydrocarbons exhibited consistent spatial variations that could be related to distance from the produced water out fall. Analysis of chemical fossil ''biomarkers'' provides potentially useful indices of effects of waste discharges upon microbial biodegradation of organic compounds in sediments

  2. An evaporated seawater origin for the ore-forming brines in unconformity-related uranium deposits (Athabasca Basin, Canada): Cl/Br and δ 37Cl analysis of fluid inclusions

    Science.gov (United States)

    Richard, Antonin; Banks, David A.; Mercadier, Julien; Boiron, Marie-Christine; Cuney, Michel; Cathelineau, Michel

    2011-05-01

    Analyses of halogen concentration and stable chlorine isotope composition of fluid inclusions from hydrothermal quartz and carbonate veins spatially and temporally associated with giant unconformity-related uranium deposits from the Paleoproterozoic Athabasca Basin (Canada) were performed in order to determine the origin of chloride in the ore-forming brines. Microthermometric analyses show that samples contain variable amounts of a NaCl-rich brine (Cl concentration between 120,000 and 180,000 ppm) and a CaCl 2-rich brine (Cl concentration between 160,000 and 220,000 ppm). Molar Cl/Br ratios of fluid inclusion leachates range from ˜100 to ˜900, with most values between 150 and 350. Cl/Br ratios below 650 (seawater value) indicate that the high salinities were acquired by evaporation of seawater. Most δ 37Cl values are between -0.6‰ and 0‰ (seawater value) which is also compatible with a common evaporated seawater origin for both NaCl- and CaCl 2-rich brines. Slight discrepancies between the Cl concentration, Cl/Br, δ 37Cl data and seawater evaporation trends, indicate that the evaporated seawater underwent secondary minor modification of its composition by: (i) mixing with a minor amount of halite-dissolution brine or re-equilibration with halite during burial; (ii) dilution in a maximum of 30% of connate and/or formation waters during its migration towards the base of the Athabasca sandstones; (iii) leaching of chloride from biotites within basement rocks and (iv) water loss by hydration reactions in alteration haloes linked to uranium deposition. The chloride in uranium ore-forming brines of the Athabasca Basin has an unambiguous dominantly marine origin and has required large-scale seawater evaporation and evaporite deposition. Although the direct evidence for evaporative environments in the Athabasca Basin are lacking due to the erosion of ˜80% of the sedimentary pile, Cl/Br ratios and δ 37Cl values of brines have behaved conservatively at the basin

  3. Brine Transport Experiments in Granular Salt

    Energy Technology Data Exchange (ETDEWEB)

    Jordan, Amy B. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Boukhalfa, Hakim [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Caporuscio, Florie Andre [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stauffer, Philip H. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-06-06

    To gain confidence in the predictive capability of numerical models, experimental validation must be performed to ensure that parameters and processes are correctly simulated. The laboratory investigations presented herein aim to address knowledge gaps for heat-generating nuclear waste (HGNW) disposal in bedded salt that remain after examination of prior field and laboratory test data. Primarily, we are interested in better constraining the thermal, hydrological, and physicochemical behavior of brine, water vapor, and salt when moist salt is heated. The target of this work is to use run-of-mine (RoM) salt; however during FY2015 progress was made using high-purity, granular sodium chloride.

  4. Environmental Management System of Petroleum Industries: A case study of Oil and Gas Exploration in the Zamrud Field Conservation Areas

    Directory of Open Access Journals (Sweden)

    Onny Setiani

    2015-12-01

    Full Text Available ABSTRACT Background:The Zamrud Field is one of the oil fields managed by Caltex Pacific Indonesia (CPI a production sharing contractor of Pertamina. It is located in the Coastal Plain and  Pekanbaru (CPP Block. The government of Indonesia has designated Zamrud as a conservation area. The petroleum industry in Zamrud fields has received 14001 ISO Certificate on Environmental Management System. The production sharing contract between CPI and the Government of Indonesia expired in August 2002 Methods: .This case study describes how CPI managed the development  of oil and gas production and compared to  the environmental management system for  petroleum industries  that should be taken  in the Zamrud conservation areas. Results: A number of specific measures were employed by CPI  to protect this sensitive area including a green seismic project, zero-discharge drilling, water management, preservation of nature and regular monitoring and impact assessment. There are two  important points that should be in consideration  for the environmental management system by CPI in the Zamrud areas, including top soil utilization to maintain biological and nutrients quality and re-vegetation in all areas of significant disturbances. Conclusion: oil and gas  exploration and production in conservation areas has to be managed through high commitment to good environmental  and social practices. Key words     : Environmental Management System (EMS, Petroleum Industries, Zamrud Field

  5. Petroleum: the new challenges. Market pressure and technological lever

    International Nuclear Information System (INIS)

    Boy de la Tour, X.

    1992-01-01

    This paper describes the forecasting of petroleum demand during the next years, the state of petroleum reserves and recognized oil fields in the whole world at the present time. The challenge to obtain a sufficient petroleum production, facing an increased energy demand, requires to have recourse to new exploration and oil recovery techniques. 8 refs., 5 figs., 1 tab

  6. Brine: a computer program to compute brine migration adjacent to a nuclear waste canister in a salt repository

    International Nuclear Information System (INIS)

    Duckworth, G.D.; Fuller, M.E.

    1980-01-01

    This report presents a mathematical model used to predict brine migration toward a nuclear waste canister in a bedded salt repository. The mathematical model is implemented in a computer program called BRINE. The program is written in FORTRAN and executes in the batch mode on a CDC 7600. A description of the program input requirements and output available is included. Samples of input and output are given

  7. Oil exudation and histological structures of duck egg yolks during brining.

    Science.gov (United States)

    Lai, K M; Chung, W H; Jao, C L; Hsu, K C

    2010-04-01

    Changes in oil exudation and histological structures of salted duck egg yolks during brining up to 5 wk were investigated. During brining, the salt contents of albumen, exterior yolk (hardened portion), and interior yolk (soft or liquid portion) gradually increased accompanied by slight decreases in moisture content. The hardening ratio of salted egg yolks increased rapidly to about 60% during the first week of brining and then reached 100% at the end of brining. After brining, part of the lipids in salted egg yolk became free due to the structural changes of low-density lipoprotein induced by dehydration and increase of salt content, and more free lipids in salted egg yolk were released after the cooking process. With the brining time increased up to 5 wk, the outer region of the cooked salted yolk gradually changed into dark brown, brown, orange, and then dark brown, whereas the center region changed into light yellow, yellow, dark yellow, and then yellow again. The microstructures of cooked salted egg yolks showed that the yolk spheres in the outer and middle regions retained their original shape, with some shrinking and being packed more loosely when brining time increased, and the exuded oil filled the space between the spheres. Furthermore, the yolk spheres in the center region transformed to a round shape but still showed granulation after 4 wk of brining, whereas they were mostly disrupted after 2 to 5 wk of brining. One of the most important characteristics of cooked salted egg yolks, gritty texture, contributed to oil exudation and granulated yolk spheres were observed at the brining time of 4 wk.

  8. Natural gas in 1942: Petroleum in 1942: Gravimetric and magnetic geophysical surveys in the gas fields of southwestern Ontario, 1941 and 1942. Annual publication

    Energy Technology Data Exchange (ETDEWEB)

    Crozier, A R; Brant, A A

    1946-12-31

    Part V of this annual report consists of three separate reports: Natural gas; petroleum; and gravimetric and magnetic geophysical surveys in the gas fields of southwestern Ontario. The natural gas report discusses production and distribution; changes and improvements; consumption and rates; and gas wells and their production. The petroleum report presents information on production and drilling by township; expansion; and petroleum importation and refining operations. The final report discusses causes of anomalies; a discussion of the gravitational results and a discussion of the magnetic results.

  9. Human Resource Local Content in Ghana's Upstream Petroleum Industry

    Science.gov (United States)

    Benin, Papa

    Enactment of Ghana's Petroleum (Local Content and Local Participation) Regulations, 2013 (L.I. 2204) was intended to regulate the percentage of local products, personnel, financing, and goods and services rendered within Ghana's upstream petroleum industry value chain. Five years after the inception of Ghana's upstream oil and gas industry, a gap is evident between the requirements of L.I. 2204 and professional practice. Drawing on Lewin's change theory, a cross-sectional study was conducted to examine the extent of differences between the prevailing human resource local content and the requirements of L.I. 2204 in Ghana's upstream petroleum industry. The extent to which training acquired by indigenous Ghanaians seeking jobs in Ghana's oil fields affects the prevalent local content in its upstream petroleum industry was also examined. Survey data were collected from 97 management, technical, and other staff in 2 multinational petroleum companies whose oil and gas development plans have been approved by the Petroleum Commission of Ghana. To answer the research questions and test their hypotheses, one-way ANOVA was performed with staff category (management, technical, and other) as the independent variable and prevalent local content as the dependent variable. Results indicated that prevailing local content in Ghana's upstream petroleum industry meets the requirements of L.I. 2204. Further, training acquired by indigenous Ghanaians seeking jobs in Ghana's oil fields affects the prevalent local content in its offshore petroleum industry. Findings may encourage leaders within multinational oil companies and the Petroleum Commission of Ghana to organize educational seminars that equip indigenous Ghanaians with specialized skills for working in Ghana's upstream petroleum industry.

  10. Modeling Episodic Ephemeral Brine Lake Evaporation and Salt Crystallization on the Bonneville Salt Flats, Utah

    Science.gov (United States)

    Liu, T.; Harman, C. J.; Kipnis, E. L.; Bowen, B. B.

    2017-12-01

    Public concern about apparent reductions in the areal extent of the Bonneville Salt Flat (BSF) and perceived changes in inundation frequency has motivated renewed interest in the hydrologic and geochemical behavior of this salt playa. In this study, we develop a numerical modeling framework to simulate the relationship between hydrometeorologic variability, brine evaporation and salt crystallization processes on BSF. The BSF, locates in Utah, is the remnant of paleo-lake Bonneville, and is capped by up to 1 meter of salt deposition over a 100 km2 area. The BSF has two distinct hydrologic periods each year: a winter wet periods with standing surface brine and the summer dry periods when the brine is evaporated, exposing the surface salt crust. We develop a lumped non-linear dynamical models coupling conservation expressions from water, dissolved salt and thermal energy to investigate the seasonal and diurnal behavior of brine during the transition from standing brine to exposed salt at BSF. The lumped dynamic models capture important nonlinear and kinetic effects introduced by the high ionic concentration of the brine, including the pronounced effect of the depressed water activity coefficient on evaporation. The salt crystallization and dissolution rate is modeled as a kinetic process linearly proportional to the degree of supersaturation of brine. The model generates predictions of the brine temperature and the solute and solvent masses controlled by diurnal net radiation input and aerodynamic forcing. Two distinct mechanisms emerge as potential controls on salt production and dissolution: (1) evapo-concentration and (2) changes in solubility related to changes in brine temperature. Although the evaporation of water is responsible for ultimate disappearance of the brine each season ,variation in solubility is found to be the dominant control on diurnal cycles of salt precipitation and dissolution in the BSF case. Most salt is crystallized during nighttime, but the

  11. Chemistry of glass corrosion in high saline brines

    International Nuclear Information System (INIS)

    Grambow, B.; Mueller, R.

    1990-01-01

    Corrosion data obtained in laboratory tests can be used for the performance assessment of nuclear waste glasses in a repository if the data are quantitatively described in the frame of a geochemical model. Experimental data were obtained for conventional pH values corrected for liquid junction, amorphous silica solubility and glass corrosion in concentrated salt brines. The data were interpreted with a geochemical model. The brine chemistry was described with the Pitzer formalism using a data base which allows calculation of brine compositions in equilibrium with salt minerals at temperatures up to 200C. In MgCl 2 dominated brines Mg silicates form and due to the consumption of Mg the pH decreases with proceeding reaction. A constant pH (about 4) and composition of alteration products is achieved, when the alkali release from the glass balances the Mg consumption. The low pH results in high release of rare earth elements REE (rare earth elements) and U from the glass. In the NaCl dominated brine MgCl 2 becomes exhausted by Mg silicate formation. As long as there is still Mg left in solution the pH decreases. After exhaustion of Mg the pH rises with the alkali release from the glass and analcime is formed

  12. Russian petroleum tax policy – Continuous maneuvering in rocky waters

    International Nuclear Information System (INIS)

    Fjaertoft, Daniel; Lunden, Lars Petter

    2015-01-01

    This article maps and analyses petroleum taxation policy in Russia to investigate the extent to which it reaches the goal of maximizing government revenue from new petroleum field developments. Expected cash flows from four real-world fields in Russia are modeled in four real-world tax regimes in an attempt to determine whether the so-called ‘tax maneuver’ of December 2014 helps the government to reach its goal. Russia's tax policy is further analyzed in terms of the desirable tax system design features of simplicity, flexibility, stability and competitiveness. The article concludes that the changes to the tax system introduced additional incentives for field developments but failed both to improve tax system design per se and to maximize government tax revenue. - Highlights: • Petroleum tax revenue is the Russian government’s largest single source of revenue. • Tax legislation has not maximized government revenue from the petroleum industry. • The December 2014 tax reform is just one in a long line of reforms and amendments. • Russian petroleum taxation is set to change perpetually.

  13. Space and Industrial Brine Drying Technologies

    Science.gov (United States)

    Jones, Harry W.; Wisniewski, Richard S.; Flynn, Michael; Shaw, Hali

    2014-01-01

    This survey describes brine drying technologies that have been developed for use in space and industry. NASA has long considered developing a brine drying system for the International Space Station (ISS). Possible processes include conduction drying in many forms, spray drying, distillation, freezing and freeze drying, membrane filtration, and electrical processes. Commercial processes use similar technologies. Some proposed space systems combine several approaches. The current most promising candidates for use on the ISS use either conduction drying with membrane filtration or spray drying.

  14. Disposal/recovery options for brine waters from oil and gas production in New York State. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Matsumoto, M.R.; Atkinson, J.F.; Bunn, M.D.; Hodge, D.S.

    1996-03-01

    Produced water from oil and gas operations, or brine as it is typically referred, may be characterized as being highly saline, with total dissolved solids greater than 100 g/L. If these bribes are disposed improperly there may be severe adverse environmental effects. Thus, it is important that brine be disposed using environmentally sound methods. Unfortunately, costs for the disposal of brine water are a significant burden to oil and gas producers in New York State. These costs and the relatively low market price of oil and natural gas have contributed to the decline in gas and oil production in New York State during the past 10 years. The objectives of this study were to evaluate new and existing options for brine disposal in New York State, examine the technical and economic merits of these options, and assess environmental impacts associated with each option. Two new disposal options investigated for New York State oil and gas producers included construction of a regional brine treatment facility to treat brine prior to discharge into a receiving water and a salt production facility that utilizes produced water as a feed stock. Both options are technically feasible; however, their economic viability depends on facility size and volume of brine treated.

  15. Disposal/recovery options for brine waters from oil and gas production in New York State. Final report

    International Nuclear Information System (INIS)

    Matsumoto, M.R.; Atkinson, J.F.; Bunn, M.D.; Hodge, D.S.

    1996-03-01

    Produced water from oil and gas operations, or brine as it is typically referred, may be characterized as being highly saline, with total dissolved solids greater than 100 g/L. If these bribes are disposed improperly there may be severe adverse environmental effects. Thus, it is important that brine be disposed using environmentally sound methods. Unfortunately, costs for the disposal of brine water are a significant burden to oil and gas producers in New York State. These costs and the relatively low market price of oil and natural gas have contributed to the decline in gas and oil production in New York State during the past 10 years. The objectives of this study were to evaluate new and existing options for brine disposal in New York State, examine the technical and economic merits of these options, and assess environmental impacts associated with each option. Two new disposal options investigated for New York State oil and gas producers included construction of a regional brine treatment facility to treat brine prior to discharge into a receiving water and a salt production facility that utilizes produced water as a feed stock. Both options are technically feasible; however, their economic viability depends on facility size and volume of brine treated

  16. Basic petroleum research. Final report; Grunnleggende petroleumsforskning. Sluttrapport

    Energy Technology Data Exchange (ETDEWEB)

    Roesjoe, Bjarne; Stiksrud, Helge

    2004-07-01

    An overview of projects in the field of basic petroleum research (PetroForsk) is presented. A brief presentation of some of the projects is included, as well as political comments on the value of these projects. The research program Basic Petroleum Research (PetroForsk) was established in 1998 and ended in 2004. The program has been part of the Research Council of Norway's long-term effort in petroleum research (ml)

  17. Pressurized brines in continental Antarctica as a possible analogue of Mars

    OpenAIRE

    Forte, Emanuele; Dalle Fratte, Michele; Azzaro, Maurizio; Guglielmin, Mauro

    2016-01-01

    Interest in brines in extreme and cold environments has recently increased after they have been found on Mars. Those brines can be potential new subsurface habitats for peculiar ecosystems. In the McMurdo Dry Valleys of the Antarctic, the best analogue for Mars conditions, only a few cases of brines have been identified in some perennially frozen lakes and in one case in an underground aquifer. Here, we present the occurrence of pressurized brines in a shallow perennially ice-covered lake sou...

  18. Calcium extraction from brine water and seawater using oxalic acid

    Science.gov (United States)

    Natasha, Nadia Chrisayu; Lalasari, Latifa Hanum

    2017-01-01

    Calcium can be extracted not only from rocks but also from natural liquor such as seawater and brine water. In order to extract the calcium from seawater and brine water, oxalic acid was used in this research. Effect of variations of the volume of the oxalic acid at a constant concentration in seawater and brine water to produce calcium was investigated. The concentration of oxalic acid was 100 g/l and the variations of its volume were 2 ml, 4 ml, 6 ml, 8 ml, 10 ml, 20 ml, 30 ml, 40 ml, and 50 ml. The used seawater and brine water were firstly evaporated from 100 ml into 50 ml and then the oxalic acid was added into them with mixing to produce the calcium precipitates. The precipitates were analyzed by X-ray diffraction (XRD) and scanning electron microscope (SEM) and the filtrates were analyzed by inductively coupled plasma-optical emission spectrometry (ICP-OES). The SEM analysis showed that the precipitates from brine water were consisted of only calcium compound while from seawater sodium one was also found along with calcium compound. The XRD analysis showed that the calcium was present in the form of calcium oxalate for both seawater and brine water. The ICP-OES analysis of the filtrate from seawater precipitation showed that the its calcium content was decreased from 826.20 ppm to 0.04 ppm while from brine water, it decreased from 170.06 ppm to 1.96 ppm. These results showed that both seawater and brine water have the potential to be a raw material for calcium production.

  19. Pressurized brines in continental Antarctica as a possible analogue of Mars.

    Science.gov (United States)

    Forte, Emanuele; Dalle Fratte, Michele; Azzaro, Maurizio; Guglielmin, Mauro

    2016-09-12

    Interest in brines in extreme and cold environments has recently increased after they have been found on Mars. Those brines can be potential new subsurface habitats for peculiar ecosystems. In the McMurdo Dry Valleys of the Antarctic, the best analogue for Mars conditions, only a few cases of brines have been identified in some perennially frozen lakes and in one case in an underground aquifer. Here, we present the occurrence of pressurized brines in a shallow perennially ice-covered lake south of 70°S in an ice-free area of Victoria Land, Antarctica. For the first time, we also imaged, by means of ground penetrating radar data, the existence of a pingo-like-feature (PLF) formed by the extrusion of brines, which has also been confirmed by borehole evidence. Those brines are fed by an underground talik external to the lake basin, enhancing the possibility of unexploited ecosystems that could find an analogue in Martian environments.

  20. Photocatalytic reduction of nitrate using titanium dioxide for regeneration of ion exchange brine.

    Science.gov (United States)

    Yang, Ting; Doudrick, Kyle; Westerhoff, Paul

    2013-03-01

    Nitrate is often removed from groundwater by ion exchange (IX) before its use as drinking water. Accumulation of nitrate in IX brine reduces the efficiency of IX regeneration and the useful life of the regeneration brine. For the first time, we present a strategy to photocatalytically reduce nitrate in IX brine, thereby extending the use of the brine. Titanium dioxide (Evonik P90), acting as photocatalyst, reduced nitrate effectively in both synthetic brines and sulfate-removed IX brine when formic acid (FA) was used as the hole scavenger (i.e., electron donor) and the initial FA to nitrate molar ratio (IFNR) was 5.6. Increasing the NaCl level in the synthetic brine slowed the nitrate reduction rate without affecting by-product selectivity of ammonium and gaseous N species (e.g., N(2), N(2)O). In a non-modified IX brine, nitrate removal was greatly inhibited owing to the presence of sulfate, which competed with nitrate for active surface sites on P90 and induced aggregation of P90 nanoparticles. After removing sulfate through barium sulfate precipitation, nitrate was effectively reduced; approximately 3.6 × 10(24) photons were required to reduce each mole of nitrate to 83% N Gases and 17% NH(4)(+). To make optimum use of FA and control the residual FA level in treated brine, the IFNR was varied. High IFNRs (e.g., 4, 5.6) were found to be more efficient for nitrate reduction but left higher residual FA in brine. IX column tests were performed to investigate the impact of residual FA for brine reuse. The residual FA in the brine did not significantly affect the nitrate removal capacity of IX resins, and formate contamination of treated water could be eliminated by rinsing with one bed volume of fresh brine. Copyright © 2012 Elsevier Ltd. All rights reserved.

  1. Petroleum. [Venezuela

    Energy Technology Data Exchange (ETDEWEB)

    1976-01-01

    An introductory chapter of world wide petroleum history is followed by a comprehensive record of the petroliferous basins of Venezuela. Exploration, productivity, production statistics, reserves, geologic structures, and the distribution of oil and gas fields are described separately for the Maracaibo-Falcon basin, Apure-Barinas basin, E. Venezuela basin, and Tuy-Cariaco basin. The descriptions include geographic distribution, geomorphologic outline of the basins, lithology and thickness of sediments, structural development, present structural conditions in which oil and gas fields occur, and their distribution in the basins. Economic factors are discussed in an appendix. 145 references.

  2. Laws of the electrochemical soils remediation from petroleum pollution

    Energy Technology Data Exchange (ETDEWEB)

    Korolev, V.A. [Moscow State Univ. (Russian Federation)

    2001-07-01

    The man-caused petroleum pollution of humus and soils in places of oil production, and also the pollution of geological environment by petroleum is carried out in growing scales. Very much frequently of ground and soils become soiled by petroleum at failures during transportation of petroleum. The humus and clay soils polluted by petroleum causes destruction ecosystems and landscapes. Therefore finding - out of the nature and mechanisms of interaction water-saturated dispersed soils with the liquid hydrocarbons becomes one of priority problems in the field of ecological geology. The development of methods of electrochemical clearing soils from the liquid hydrocarbons pollution is the important task too. Therefore, the study of dependences of a double electrical layer (DEL) parameters of the water-petroleum-saturated caolinite clay and electrochemical migration in it of petroleum was the purpose of the present work. (orig.)

  3. Did you know? Petroleum industry fast facts: Newfoundland

    International Nuclear Information System (INIS)

    1999-10-01

    This is part of a series of brochures published by the Petroleum Communication Foundation, a non-profit society established in 1975. The foundation's objective is to stimulate public awareness and understanding of Canada's petroleum industry and its contribution to the economy of each of the provinces where the industry's presence and impact is substantial. This brochure provides brief, but useful, information about the province of Newfoundland, its size (405,720 sq.km), capital (St. John's), population (543.800 in 1998) major industries (petroleum and mining, manufacturing, fishing, logging and forestry, electricity and tourism), and revenue from natural resources ($ 175 million in 1998/1999, primarily in the form of expenditure commitments relating to exploration leases offshore and onshore). Also included are some facts about the petroleum industry in Newfoundland, (exploration and pre-production work in the offshore Terra Nova field, construction and development of the Hibernia project with production beginning in 1998, employment, etc.), and upstream industry expenditures in the province (about $ 1.15 billion in 1998). It is expected that by 2004 when the Terra Nova and White Rose projects are fully on stream, Newfoundland will produce one-third of Canada's conventional light crude oil output. map, pie-chart, figs

  4. Thermal-gradient migration of brine inclusions in salt crystals

    International Nuclear Information System (INIS)

    Yagnik, S.K.

    1982-09-01

    It has been proposed that high-level nuclear waste be disposed in a geologic repository. Natural-salt deposits, which are being considered for this purpose, contain a small volume fraction of water in the form of brine inclusions distributed throughout the salt. Radioactive-decay heating of the nuclear wastes will impose a temperature gradient on the surrounding salt which mobilizes the brine inclusions. Inclusions filled completely with brine migrate up the temperature gradient and eventually accumulate brine near the buried waste forms. The brine may slowly corrode or degrade the waste forms which is undesirable. In this work, thermal gradient migration of both all-liquid and gas-liquid inclusions was experimentally studied in synthetic single crystals of NaCl and KCl using a hot-stage attachment to an optical microscope which was capable of imposing temperature gradients and axial compressive loads on the crystals. The migration velocities of the inclusions were found to be dependent on temperature, temperature gradient, and inclusion shape and size. The velocities were also dictated by the interfacial mass transfer resistance at brine/solid interface. This interfacial resistance depends on the dislocation density in the crystal, which in turn, depends on the axial compressive loading of the crystal. At low axial loads, the dependence between the velocity and temperature gradient is non-linear.At high axial loads, however, the interfacial resistance is reduced and the migration velocity depends linearly on the temperature gradient. All-liquid inclusions filled with mixed brines were also studied. For gas-liquid inclusions, three different gas phases (helium, air and argon) were compared. Migration studies were also conducted on single crystallites of natural salt as well as in polycrystalline natural salt samples. The behavior of the inclusions at large angle grain boundaries was observed. 35 figures, 3 tables

  5. Thermal gradient migration of brine inclusions in salt crystals

    International Nuclear Information System (INIS)

    Yagnik, S.K.

    1982-01-01

    Natural salt deposits, which are being considered for high-level nuclear wastes repositories, contain a small volume fraction of water in the form of brine inclusions distributed throughout the salt. Radioactive decay heating of the nuclear wastes will impose a temperature gradient on the surrounding salt which mobilizes the brine inclusions. Inclusions filled completely with brine (the all-liquid inclusions) migrate up the temperature gradient and eventually accumulate brine near the buried waste forms. The brine may slowly corrode or degrade the waste forms which is undesirable. In the present work, thermal gradient migration of both all-liquid and gas-liquid inclusions was experimentally studied in synthetic single crystals of NaCl and KCl using a hot-stage attachment to an optical microscope which was capable of imposing temperature gradients and axial compressive loads on the crystals. The migration velocities of the inclusions were found to be dependent on temperature, temperature gradient, and inclusion shape and size. The velocities were also dictated by the interfacial mass transfer resistance at brine/solid interface. This interfacial resistance depends on the dislocation density in the crystal, which in turn, depends on the axial compressive loading of the crystal. At low axial loads, the dependence between the velocity and temperature gradient is nonlinear. At high axial loads, however, the interfacial resistance is reduced and the migration velocity depends linearly on the temperature gradient. All-liquid inclusions filled with mixed brines were also studied. For gas-liquid inclusions, three different gas phases (helium, air and argon) were compared. Migration studies were also conducted on single crystallites of natural salt as well as in polycrystalline natural salt samples. The behavior of the inclusions at large angle grain boudaries was observed

  6. Membrane Lipids as Indicators for Viable Bacterial Communities Inhabiting Petroleum Systems.

    Science.gov (United States)

    Gruner, Andrea; Mangelsdorf, Kai; Vieth-Hillebrand, Andrea; Horsfield, Brian; van der Kraan, Geert M; Köhler, Thomas; Janka, Christoph; Morris, Brandon E L; Wilkes, Heinz

    2017-08-01

    Microbial activity in petroleum reservoirs has been implicated in a suite of detrimental effects including deterioration of petroleum quality, increases in oil sulfur content, biofouling of steel pipelines and other infrastructures, and well plugging. Here, we present a biogeochemical approach, using phospholipid fatty acids (PLFAs), for detecting viable bacteria in petroleum systems. Variations within the bacterial community along water flow paths (producing well, topside facilities, and injection well) can be elucidated in the field using the same technique, as shown here within oil production plants in the Molasse Basin of Upper Austria. The abundance of PLFAs is compared to total cellular numbers, as detected by qPCR of the 16S rDNA gene, to give an overall comparison between the resolutions of both methods in a true field setting. Additionally, the influence of biocide applications on lipid- and DNA-based quantification was investigated. The first oil field, Trattnach, showed significant PLFA abundances and cell numbers within the reservoir and topside facilities. In contrast, the second field (Engenfeld) showed very low PLFA levels overall, likely due to continuous treatment of the topside facilities with a glutaraldehyde-based antimicrobial. In comparison, Trattnach is dosed once per week in a batch fashion. Changes within PLFA compositions across the flow path, throughout the petroleum production plants, point to cellular adaptation within the system and may be linked to shifts in the dominance of certain bacterial types in oil reservoirs versus topside facilities. Overall, PLFA-based monitoring provides a useful tool to assess the abundance and high-level taxonomic diversity of viable microbial populations in oil production wells, topside infrastructure, pipelines, and other related facilities.

  7. Permeability of salt-crystal interfaces to brine

    International Nuclear Information System (INIS)

    Gilpatrick, L.O.; Baes, C.F. Jr.; Shor, A.J.; Canonico, C.M.

    1982-06-01

    To investigate the movement of brine along grain boundaries in polycrystalline salt, measurements have been made of the radial flow of brine through the interface between cylindrical salt crystals under axial stresses to 140 bar and temperatures to 80 0 C. For constant conditions, the total flow of brine showed a linear dependence on the logarithm of time, and the reciprocal permeability increased linearly with time. Loss of salt from the interface by pressure solution effects was more than enough to account for the decrease in the apparent thickness of the interface (i.e., that which may be estimated for an interface of the same permeability formed by plane parallel surfaces). This apparent thickness, initially as large as 10 μm, decreased to as little as 0.2 μm with exposure to stress and flowing brine. It decreased quickly with sudden increases in axial stress and usually increased, though not reversibly, with decreases in stress. The rate of increase in the reciprocal permeability with time was roughly proportional to the stress and to the square of the hydraulic pressure drop. Assuming similar apparent thicknesses for the grain boundaries in polycrystalline salt, permeabilities are predicted that are quite consistent with the low values reported for stressed core specimens

  8. Brine chemistry and control of adverse chemical reactions with natural gas production. Annual report, July 1990-June 1991

    Energy Technology Data Exchange (ETDEWEB)

    Oddo, J.E.; Kan, A.T.; Cao, X.; Hunter, M.; Tomson, M.B.

    1991-08-01

    A significant quantity of brine is produced along with nearly all gas production. In addition to disposal, three specific chemistry problems occur: (1) scale formation; (2) carbon dioxide corrosion; (3) solids or turbidity production. Additionally, there are numerous specific analytical chemistry issues which require attention. Several research oriented small test squeezes were performed in the Delee Well. Results of these test squeezes were used to better design a full-sized squeeze at the O'Daniels No. 2 Well in the Alta Loma East field, near Galveston, Texas. Sulfate scale formation is common in offshore gas production, because of the high sulfate content in sea water. Preliminary work has been completed on sulfate scale prediction for the common scales of calcium, strontium and barium. These predictive algorithms have been developed for field use and are based upon readily measured brine parameters. Corresponding laboratory work on sulfate inhibition has been started using a newly developed high temperature and pressure flow through apparatus. Flow through core tests have been conducted to determine the important mechanisms of inhibition retention and release in the field. These results are summarized along with their major implications to squeeze design. Also, a new method has been developed and a patent application filed for low level phosphonate inhibition analysis in produced brines.

  9. Concentrated Brine Treatment using New Energy in Coal Mine Evaporation Ponds

    Science.gov (United States)

    Li, Ting; Li, Jingfeng

    2017-12-01

    Recently, more and more coal mine water is being advanced treated and reused in China. The concentrated brine that results from advanced treatment methods can only be evaporated in an evaporation pond. Because of limited treatment capabilities and winter freezing, evaporation ponds often overflow, causing environment contamination. In this paper, based on analysis of brine water quality and economic-technical feasibility, we present a suitable treatment method for brine in evaporation ponds as electrodialysis using solar energy. In addition, we propose a new system to treat brine in coal mine evaporation ponds, which is powered by solar and wind. The operating efficiency of this treatment system proposed in this paper can meet the concentrated brine treatment demands in most coal mines in western mining areas of China and it places the photovoltaic power generation plates on the surface of the evaporation pond on a fixed floating island, which reduces any risk associated with land acquisition. This system can enhance brine treatment efficiency, requires a reduced evaporation pond area, increases the utilization of coal mine water, and minimizes the risk of environment contamination.

  10. A novel lignin-based surfactant system for the Salem Unit

    International Nuclear Information System (INIS)

    DeBons, F.E.; Whittington, L.E.

    1991-01-01

    Texaco conducted a successful surfactant/polymer flood in a 60-acre [24 ha] portion of the Salem Benoist reservoir in Salem, Illinois, in 1981. This pilot used a brine-tolerant petroleum sulfonate surfactant system blended in injection brine followed by a xanthan mobility control polymer in fresher water. The oil recovery over the seven year life of the flood was 487,050 bbl [77 435 m 3 ]. This represents 45% of the oil remaining in the total thickness of 73% of that from the more permeable lower interval where most of the surfactant flowed. Since this successful project, Texaco has continued to improve enhanced oil recovery surfactant systems. We have developed novel, brine tolerant surfactants based on the renewable resources lignin and tallow amine. This paper describes the laboratory work leading to a surfactant system which has been recommended for field testing. The laboratory work includes blending, interfacial tension measurements, and core floods in Berea and reservoir cores. The type of lignin based surfactant system described in this report has applicability in all fields where conventional petroleum-based surfactants have been used. Their much lower cost means that they can be used economically at lower crude oil prices

  11. Aerobic methanotrophic communities at the Red Sea brine-seawater interface

    Directory of Open Access Journals (Sweden)

    Rehab Z. Abdallah

    2014-09-01

    Full Text Available The central rift of the Red Sea contains 25 brine pools with different physicochemical conditions, dictating the diversity and abundance of the microbial community. Three of these pools, the Atlantis II, Kebrit and Discovery Deeps, are uniquely characterized by a high concentration of hydrocarbons. The brine-seawater interface, described as an anoxic-oxic (brine-seawater boundary, is characterized by a high methane concentration, thus favoring aerobic methane oxidation. The current study analyzed the aerobic free–living methane-oxidizing bacterial communities that potentially contribute to methane oxidation at the brine-seawater interfaces of the three aforementioned brine pools, using metagenomic pyrosequencing, 16S rRNA pyrotags and pmoA library constructs. The sequencing of 16S rRNA pyrotags revealed that these interfaces are characterized by high microbial community diversity. Signatures of aerobic methane-oxidizing bacteria were detected in the Atlantis II Interface (ATII-I and the Kebrit Deep Upper (KB-U and Lower (KB-L brine-seawater interfaces. Through phylogenetic analysis of pmoA, we further demonstrated that the ATII-I aerobic methanotroph community is highly diverse. We propose four ATII-I pmoA clusters. Most importantly, cluster 2 groups with marine methane seep methanotrophs, and cluster 4 represent a unique lineage of an uncultured bacterium with divergent alkane monooxygenases. Moreover, non-metric multidimensional scaling (NMDS based on the ordination of putative enzymes involved in methane metabolism showed that the Kebrit interface layers were distinct from the ATII-I and DD-I brine-seawater interfaces.

  12. REDUCING POWER PRODUCTION COSTS BY UTILIZING PETROLEUM COKE

    Energy Technology Data Exchange (ETDEWEB)

    Kevin C. Galbreath; Donald L. Toman; Christopher J. Zygarlicke

    1999-09-01

    Petroleum coke, a byproduct of the petroleum-refining process, is an attractive primary or supplemental fuel for power production primarily because of a progressive and predictable increase in the production volumes of petroleum coke (1, 2). Petroleum coke is most commonly blended with coal in proportions suitable to meet sulfur emission compliance. Petroleum coke is generally less reactive than coal; therefore, the cofiring of petroleum coke with coal typically improves ignition, flame stability, and carbon loss relative to the combustion of petroleum coke alone. Although petroleum coke is a desirable fuel for producing relatively inexpensive electrical power, concerns about the effects of petroleum coke blending on combustion and pollution control processes exist in the coal-fired utility industry (3). The Energy & Environmental Research Center (EERC) completed a 2-year technical assessment of petroleum coke as a supplemental fuel. A survey questionnaire was sent to seven electric utility companies that are currently cofiring coal and petroleum coke in an effort to solicit specific suggestions on research needs and fuel selections. An example of the letter and survey questionnaire is presented in Appendix A. Interest was expressed by most utilities in evaluating the effects of petroleum coke blending on grindability, combustion reactivity, fouling, slagging, and fly ash emissions control. Unexpectedly, concern over corrosion was not expressed by the utilities contacted. Although all seven utilities responded to the question, only two utilities, Northern States Power Company (NSP) and Ameren, sent fuels to the EERC for evaluation. Both utilities sent subbituminous coals from the Power River Basin and petroleum shot coke samples. Petroleum shot coke is produced unintentionally during operational upsets in the petroleum refining process. This report evaluates the effects of petroleum shot coke blending on grindability, fuel reactivity, fouling/slagging, and

  13. Monitoring of Miit glass solution interactions by brine analysis

    International Nuclear Information System (INIS)

    Sassoon, R.E.; Gong, M.; Adel-Hadadi, M.; Brandys, M.; Barkatt, A.; Macedo, P.B.

    1989-01-01

    Analyses of brine samples taken from borehole MIIT=8 at the WIPP site were carried out in order to study the leaching behavior of the brine in this system. The standard addition method was used with the analytical techniques of AA, DCP and ICP-MS to determine the concentration of the components in the brine. The changes in the concentration of the major components, Na, Mg and K can be explained by reactions of the brine with the rock salt walls of the borehole. From the data obtained for the other components no leaching of the SRL-Y glass discs in the test could be observed. It was however possible to determine an upper limit for leaching of the glass from isotope ratio studies made on Li which yielded a value for the leach rate of lithium from the glass of 0.117 g m -2 d -1

  14. Petroleum and natural gas economy in Arab Countries, in Iraq, Nigeria and Tunisia

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    This paper gives informations on petroleum and natural gas industry, petroleum market and prices, trade and contracts, prospection and investments: Portugal has retained the joining to the Maghreb-Europe gas pipeline for algerian gas supply. Saudi Arabia has closed several oil fields for maintenance. New contracts have been signed for exploration or development of petroleum or natural gas fields in Nigeria, Qatar, Tunisia and Yemen

  15. The coupling of supercritical fluid chromatography and field ionization time-of-flight high-resolution mass spectrometry for rapid and quantitative analysis of petroleum middle distillates.

    Science.gov (United States)

    Qian, Kuangnan; Diehl, John W; Dechert, Gary J; DiSanzo, Frank P

    2004-01-01

    We report the first coupling of supercritical fluid chromatography (SFC) with field ionization time-of-flight high-resolution mass spectrometry (FI-ToF HRMS), in parallel with ultraviolet (UV) detection and flame ionization detection (FID), for rapid and quantitative analysis of petroleum middle distillates. SFC separates petroleum middle distillates into saturates and 1- to 3-ring aromatics. FI generates molecular ions for hydrocarbon species eluted from the SFC. The high resolution and exact mass measurements by ToF mass spectrometry provide elemental compositions of the molecules in the petroleum product. The amounts of saturates and aromatic ring types were quantified using the parallel SFC-FID assisted by SFC-UV. With a proper carbon-number calibration, the detailed composition of the petroleum middle distillate was rapidly determined.

  16. The immune-related fatty acids are responsive to CO2 driven seawater acidification in a crustacean brine shrimp Artemia sinica.

    Science.gov (United States)

    Gao, Yan; Zheng, Shu-Cheng; Zheng, Chao-Qun; Shi, Yue-Chen; Xie, Xiao-Lu; Wang, Ke-Jian; Liu, Hai-Peng

    2018-04-01

    The gradual increase of CO 2 concentration in the atmosphere, absorbed by the ocean surface water through air to sea equilibration termed ocean acidification (OA), leads to the decline of pH in seawater. It is not clear so far how the composition of fatty acids, particular the immune-related, in marine crustacean and the subsequent energy supply in marine ecosystem are affected by OA. The brine shrimp Artemia sinica is an open and common feed that provide essential fatty acids for mariculture. In this study, the fatty acids profiles of brine shrimp cultured under different lower pH levels of CO 2 driven seawater were investigated. The results showed a significant reduction of the proportion of total saturated fatty acids under the pH7.6 within one week. Meanwhile, the percentage of total monounsaturated fatty acids was significantly decreased at day 14 under pH7.8, and this percentage gave a significant increase of proportion within one week under pH7.6. Furthermore, the relative content of total polyunsaturated fatty acids (PUFAs) was found to be clearly increased with exposure to different seawater acidification at day 1, suggesting that the brine shrimp immune response was likely to be affected by acidified seawater as the PUFAs have been well known to be involved in immunomodulatory effects through alterations on cell membrane fluidity/lipid mediators and gene expression of cell signaling pathways. Notably, eicosapentaenoic acid and docosahexaenoic acid, which have essential effect on various physiological processes such as inflammatory cytokines production and cell structural stability, were strongly increased under two lower pH treatments within one week and with the significant increase at day 1 under pH7.6. These data clearly supported the hypothesis that OA might affect fatty acids composition, likely also the innate immunity, in crustacean and the subsequent energy transfer by food-chain system in the marine ecosystem. Copyright © 2017 Elsevier Ltd. All

  17. Petroleum Migration, Filling and Biological Degradation in Mesozoic Reservoirs in the Northern North Sea

    Energy Technology Data Exchange (ETDEWEB)

    Horstad, I

    1996-12-31

    This thesis comprises five papers the first of which discusses the distribution of petroleum within the Gullfaks Field and applies conventional geochemical techniques to characterize the petroleum distribution within a single field. The paper also shows how understanding geochemical heterogeneities in the petroleum fluids helped to build a better geological model of the development of the Gullfaks Field. Based on this work an improved filling model was proposed for the Gullfaks Field. The second paper discusses the biological degradation of the hydrocarbons within the Gullfaks Field, and shows how several samples from neighbouring fields were analyzed to confirm the filling model of the field. It also demonstrates how the quantification of biological degradation of hydrocarbons in the reservoir places constraints on acceptable models of the geological development of the Tampen Spur Area. The third paper discusses the source vs. sink problems of petroleum migration in the North Sea. The fourth paper is a regional study of the petroleum migration within the Tampen Spur area and proposes a regional migration model. The fifth paper is a detailed reservoir geochemical study of the giant Troll Field on the Horda Platform and proposes a revised filling model for the field. 224 refs., 86 figs., 5 tabs.

  18. Petroleum Migration, Filling and Biological Degradation in Mesozoic Reservoirs in the Northern North Sea

    Energy Technology Data Exchange (ETDEWEB)

    Horstad, I.

    1995-12-31

    This thesis comprises five papers the first of which discusses the distribution of petroleum within the Gullfaks Field and applies conventional geochemical techniques to characterize the petroleum distribution within a single field. The paper also shows how understanding geochemical heterogeneities in the petroleum fluids helped to build a better geological model of the development of the Gullfaks Field. Based on this work an improved filling model was proposed for the Gullfaks Field. The second paper discusses the biological degradation of the hydrocarbons within the Gullfaks Field, and shows how several samples from neighbouring fields were analyzed to confirm the filling model of the field. It also demonstrates how the quantification of biological degradation of hydrocarbons in the reservoir places constraints on acceptable models of the geological development of the Tampen Spur Area. The third paper discusses the source vs. sink problems of petroleum migration in the North Sea. The fourth paper is a regional study of the petroleum migration within the Tampen Spur area and proposes a regional migration model. The fifth paper is a detailed reservoir geochemical study of the giant Troll Field on the Horda Platform and proposes a revised filling model for the field. 224 refs., 86 figs., 5 tabs.

  19. Petroleum and natural gas economy in Arab Countries, in Congo, Ethiopia, Gabon and Iran. Economie petroliere et gaziere dans les Pays Arabes, au Congo, en Ethiopie, Gabon et Iran

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    1993-05-16

    This paper gives informations on petroleum and natural gas industry, petroleum market and prices, trade and contracts, prospection and investments: Portugal has retained the candidature of ten foreign companies for the introduction of natural gas in 1996 and the first enhanced recovery contract will relate to Rhourde El Baguel natural gas field (Algeria). New contracts have been signed for exploration or development of petroleum or natural gas fields in Gabon, Ethiopia and Libya. Iraq has restarted its petroleum exports and Iranian production has diminished.

  20. Petroleum and natural gas economy in Arab countries and in Congo, Iran, Namibia, Nigeria

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    This paper gives informations on petroleum and natural gas industry, petroleum market and prices, trade and contracts, prospection and production. In Saudi Arabia, Saudi Aramco has developed exploration program near Djeddah and has made a call up supply for the development of Haradh and Ghawar oil fields. In Iran, petroleum production will reach 4.5 Millions barrel per day in 1999. A new oil field has been discovered near Darkhavin and the new petroleum refinery of Ark has been inaugurated. In Yemen, Masila oil field will produce 120000 barrels per day. A new export project of liquefied natural gas is developed and will reached 5 millions of tons per year

  1. Recovery of energy from geothermal brine and other hot water sources

    Science.gov (United States)

    Wahl, III, Edward F.; Boucher, Frederic B.

    1981-01-01

    Process and system for recovery of energy from geothermal brines and other hot water sources, by direct contact heat exchange between the brine or hot water, and an immiscible working fluid, e.g. a hydrocarbon such as isobutane, in a heat exchange column, the brine or hot water therein flowing countercurrent to the flow of the working fluid. The column can be operated at subcritical, critical or above the critical pressure of the working fluid. Preferably, the column is provided with a plurality of sieve plates, and the heat exchange process and column, e.g. with respect to the design of such plates, number of plates employed, spacing between plates, area thereof, column diameter, and the like, are designed to achieve maximum throughput of brine or hot water and reduction in temperature differential at the respective stages or plates between the brine or hot water and the working fluid, and so minimize lost work and maximize efficiency, and minimize scale deposition from hot water containing fluid including salts, such as brine. Maximum throughput approximates minimum cost of electricity which can be produced by conversion of the recovered thermal energy to electrical energy.

  2. Protein removal from waste brines generated during ham salting through acidification and centrifugation.

    Science.gov (United States)

    Gutiérrez-Martínez, Maria del Rosario; Muñoz-Guerrero, Hernán; Alcaína-Miranda, Maria Isabel; Barat, José Manuel

    2014-03-01

    The salting step in food processes implies the production of large quantities of waste brines, having high organic load, high conductivity, and other pollutants with high oxygen demand. Direct disposal of the residual brine implies salinization of soil and eutrophication of water. Since most of the organic load of the waste brines comes from proteins leaked from the salted product, precipitation of dissolved proteins by acidification and removal by centrifugation is an operation to be used in waste brine cleaning. The aim of this study is optimizing the conditions for carrying out the separation of proteins from waste brines generated in the pork ham salting operation, by studying the influence of pH, centrifugal force, and centrifugation time. Models for determining the removal of proteins depending on the pH, centrifugal force, and time were obtained. The results showed a high efficacy of the proposed treatment for removing proteins, suggesting that this method could be used for waste brine protein removal. The best pH value to be used in an industrial process seems to be 3, while the obtained results indicate that almost 90% of the proteins from the brine can be removed by acidification followed by centrifugation. A further protein removal from the brine should have to be achieved using filtrating techniques, which efficiency could be highly improved as a consequence of the previous treatment through acidification and centrifugation. Waste brines from meat salting have high organic load and electrical conductivity. Proteins can be removed from the waste brine by acidification and centrifugation. The total protein removal can be up to 90% of the initial content of the waste brine. Protein removal is highly dependent on pH, centrifugation rate, and time. © 2014 Institute of Food Technologists®

  3. Geochemical evolution of brines in the Salar of Uyuni, Bolivia.

    Science.gov (United States)

    Rettig, S.L.; Jones, B.F.; Risacher, F.

    1980-01-01

    Recent analyses of brines from the Salars of Uyuni and Coipasa have been compared with published data for Lakes Titicaca and Poopo to evaluate solute compositional trends in these remnants of two large Pleistocene lakes once connected by overflow from the N to the S of the Bolivian Altiplano. From Titicaca to Poopo the water shows an increase in Cl and N somewhat greater than the total solutes. Ca and SO4 increase to a lesser extent than total dissolved solids, and carbonate species are relatively constant. Between Poopo and Coipasa proportions of Ca, SO4 and CO3 continue to decrease. At Coipasa and Uyuni, the great salars frequently evaporate to halite saturation. Halite crystallization is accompanied by an increased K, Mg and SO4 in residual brines. - from Authors

  4. Petroleum industry of Korea seen from industry

    Energy Technology Data Exchange (ETDEWEB)

    Kim, H.P. [SK Co, Seoul (Korea, Republic of)

    1998-05-01

    The domestic petroleum industry faced with outward opening and exchange crisis is put under the most difficult period so far, and costs reduction and securing international competitive power in software field are emerging as important assignments on which the life and death of national key industries depends not only as a restructuring issue of each petroleum company. Required strategy of petroleum industry to solve this effectively this year must be the thorough revamping through restructuring and reform of management standards not the survival exercise through price competition. For this, each petroleum company and distributor should open a new petroleum industry in which fair rules of the game are developed as well as costs reduction through joint efforts and value creation in overall industry. For this, government should support the domestic petroleum industry to stand up straight as a keeper of domestic energy industry by helping it to arm with international competitive power within a short period of time through overall needed system and legal scheme. It is because nobody can deny that energy industry is the key industry on which national existence is at stake.

  5. The role of the national petroleum company in petroleum development market

    Energy Technology Data Exchange (ETDEWEB)

    Lee, B J [Korea Energy Economics Institute, Euiwang (Korea, Republic of)

    1997-08-01

    The present century started with the creation of national petroleum companies, and it ends with those national petroleum companies exerting various types of efforts to increase the efficiency of their management. Especially, the efforts of these national petroleum companies are ever intensifying to adapt to new trends in the world petroleum market such as intensified competition, ever-deepening price unstableness, separation of structure between upstream and downstream portions, rapid development of petroleum development technologies, change of political systems and the demise of national borders, ever-increasing consciousness of environmental preservation, etc. Korea cannot be exempt from management rationalization efforts of national petroleum companies. Especially, Korea established its own national petroleum company in order to actively deal with these as its supply system is very weak. Therefore, the national petroleum company should create as many successful petroleum development businesses by actively carrying out petroleum development businesses domestically and overseas in order to establish a stable supply system of petroleum and to support the petroleum development businesses of civilian enterprises more effectively. The national petroleum company must, first of all, replace the bureaucracy with entrepreneurship. Esp., in order to enhance the efficiency of management, short- term outcome should not be emphasized over long-term tenure of petroleum development businesses, and excessive interference of government on the national petroleum company should be excluded. The entrepreneurship of the national petroleum company should be pursued in Positive-sum way, and its public image should be actively promoted through this. 35 refs., 11 figs., 32 tabs.

  6. Petroleum supply monthly

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-10-01

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blends, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  7. CONTACT ANGLE OF YUCCA MOUNTAIN WELDED TUFF WITH WATER AND BRINES

    International Nuclear Information System (INIS)

    H. Kalia

    2006-01-01

    A number of tests were performed to acquire contact angles between Yucca Mountain welded tuff from Topopah Springs Lower Lithophysal geologic unit and various brine solutions. The tests were performed on core disks received from Sample Management Facility (SMF), oven dried to a constant weight and the core disks vacuum saturated in: distilled water, J-13 water, calcium chloride brine and sodium chloride brine to constant weight. The contact angles were acquired from eight points on the surface of the core disks, four on rough surface, and four on polished surface. The contact angle was measured by placing a droplet of the test fluid, distilled water, J-13 water, calcium chloride brine and sodium chloride brine on the core disks. The objective of this test was to acquire contact angles as a potential input to estimating capillary forces in accumulated dust on the waste packages and drip shields slated for the proposed High-Level Radioactive Waste Repository at Yucca Mountain, Nevada. It was noted that once the droplet contacts the test surface, it continues to spread hence the contact angle continues to decrease with elapsed time. The maximum observed angle was at time 0 or when the drop contacted the rock surface. The measured contact angle, in all cases has significant scatter. In general, the time zero contact angles for core disks saturated in sodium chloride brine were smaller than those saturated in calcium chloride brine, distilled water, and J-13 water. The contact angles for samples saturated in distilled water, J-13 water and calcium chloride brine at time zero were similar. There was slight difference between the observed contact angles for smooth and rough surface of the test samples. The contact angles for smooth surfaces were smaller than for the rough surfaces

  8. Development and successful field tests of a multi-process phytoremediation system for decontamination of persistent petroleum and organic contaminants in soil

    Energy Technology Data Exchange (ETDEWEB)

    Greenberg, B.M.; Huang, X.-D.; Gurska, Y.; Gerhardt, K.E.; Lampi, M.A.; Khalid, A.; Isherwood, D.; Chang, P.; Wang, W.; Wang, H.; Dixon, D.G.; Glick, B.R. [Waterloo Univ., ON (Canada). Dept. of Biology

    2006-07-01

    If efficient systems with rapid remediation kinetics can be realized, phytoremediation of persistent contaminants from soils holds great promise. A multi-process phytoremediation system (MPPS) with accelerated remediation kinetics that effectively removes polycyclic aromatic hydrocarbons (PAHs), total petroleum hydrocarbons (TPHs) and chlorinated hydrocarbons (CHCs) from soils has been developed. A plant growth promoting rhizobacteria interaction is the main element for success as it mitigates stress ethylene effects in plants, leading to high root biomass which, in turn, promotes growth of rhizosphere organisms. Based on the success of greenhouse experiments, field tests of the MPPS were initiated at an Imperial Oil land farm site in Sarnia, Ontario in the summer of 2004, followed by 127 field tests at the same site in the summer of 2005 and 2006. In addition, a total petroleum hydrocarbons (TPH) contaminated site in Alberta was used in 2005 and 2006. The study presented and discussed selected results of successful greenhouse, pilot field tests and field tests of the MPPS. It was concluded that increased root biomass is achieved in the contaminated soils, which leads to more efficient and complete removal of TPHs in the field. Three years of field trials of the MPPS showed that remediation continues with successive seasons. 27 refs., 2 tabs., 1 fig.

  9. Petroleum and natural gas

    Energy Technology Data Exchange (ETDEWEB)

    060,

    1965-02-01

    Substantial increases in demand for Canadian petroleum and natural gas in both domestic and export markets resulted in another good year throughout the main sectors of the industry. In February, production averaged 850,000 bpd, or about 8% more than 1963 output of crude oil and natural gas liquids. Construction began on the first full scale plant for the extraction of oil from the Athabasca bituminous sands. In 1964, exploratory and development drilling in western Canada increased 10% from the previous year. A total of 15.5 million ft was drilled, the largest since the record drilling year of 1956. The main oil field development areas in Alberta were the House Mountain, Deer Mountain and Goose River Fields, and the Bantry-Taber heavy oil region in southeastern Alberta. Oil reserves were increased substantially by waterflood pressure maintenance projects in many of the older oil fields. The largest oil accumulation discovered in 1964 was the Syvia-Honda Field in the Devonian Gilwood sandstone in N.-central Alberta. Two graphs illustrate the crude petroleum in Canada in millions of barrels from 1940 to 1964, and natural gas in Canada in billions of cu ft from 1950 to 1964. The outlook for the industry in 1965 is good.

  10. Environment 2004. The Norwegian petroleum sector

    Energy Technology Data Exchange (ETDEWEB)

    Gooderham, Rolf E. (ed.)

    2004-07-01

    The Ministry of Petroleum and Energy produces an annual environmental review in cooperation with the Norwegian Petroleum Directorate. The purpose of this publication is threefold: (1) to increase knowledge about the environmental aspects of Norwegian oil and gas activities, (2) to take a more detailed look at a specific topic which particularly concerns both the industry and the authorities, and identify the challenges and options faced, (3) to emphasise the government's goal of ensuring that Norway reconciles its role as a large energy producer with a pioneering position on environmental issues. This year's edition focuses on the topic of produced water treatment techniques. It demonstrates that new Norwegian technology helps to limit the risk of environmental harm. New treatment techniques have been developed and adopted, but it can be difficult to understand why a specific solution is not applicable to every field. Through the thematic section in part 2, we endeavour to explain why the choice of solution will vary from field to field, and how that reflects such considerations as technical reservoir conditions and costs. The strong focus on the environmental aspects of Norwegian oil and gas production has undoubtedly helped to make the Norwegian petroleum sector a leader in this area. That reflects both the way the authorities have incorporated environmental considerations extensively into the industry's frame conditions, and from the commitment made by the industry itself. Environment 2004 also incorporates a factual section, which covers the status of emissions discharges, environmental impacts, measures to reduce discharges to the sea and emissions to the air from petroleum activities.

  11. Portable brine evaporator unit, process, and system

    Science.gov (United States)

    Hart, Paul John; Miller, Bruce G.; Wincek, Ronald T.; Decker, Glenn E.; Johnson, David K.

    2009-04-07

    The present invention discloses a comprehensive, efficient, and cost effective portable evaporator unit, method, and system for the treatment of brine. The evaporator unit, method, and system require a pretreatment process that removes heavy metals, crude oil, and other contaminates in preparation for the evaporator unit. The pretreatment and the evaporator unit, method, and system process metals and brine at the site where they are generated (the well site). Thus, saving significant money to producers who can avoid present and future increases in transportation costs.

  12. Brine reuse in ion-exchange softening: salt discharge, hardness leakage, and capacity tradeoffs.

    Science.gov (United States)

    Flodman, Hunter R; Dvorak, Bruce I

    2012-06-01

    Ion-exchange water softening results in the discharge of excess sodium chloride to the aquatic environment during the regeneration cycle. In order to reduce sodium chloride use and subsequent discharge from ion-exchange processes, either brine reclaim operations can be implemented or salt application during regeneration can be reduced. Both result in tradeoffs related to loss of bed volumes treated per cycle and increased hardness leakage. An experimentally validated model was used to compare concurrent water softening operations at various salt application quantities with and without the direct reuse of waste brine for treated tap water of typical midwestern water quality. Both approaches were able to reduce salt use and subsequent discharge. Reducing salt use and discharge by lowering the salt application rate during regeneration consequently increased hardness leakage and decreased treatment capacity. Single or two tank brine recycling systems are capable of reducing salt use and discharge without increasing hardness leakage, although treatment capacity is reduced.

  13. Crude petroleum

    International Nuclear Information System (INIS)

    1990-01-01

    Crude petroleum statistics by country of production, export values and import values from 1983 to 1988 are given. Table A.1 of the Annex includes free market prices and price indices for crude petroleum based on average of Dubai, United Kingdom Brent and Alaska N Slope crude prices (price expressed in dollars/barrel). The data sources are: Crude petroleum United Nations Statistical Office; OPEC Annual Statistical Bulletin, and Petroleum Economist. For trade the sources of data are: National trade statistics; United Nations international trade statistics; International Moneytary Fund (IMF); Organization of the Petroleum Exporting Countries (OPEC); UNCTAD secretariat estimates. Tabs

  14. Advanced oxidation of iodinated X-ray contrast media in reverse osmosis brines: the influence of quenching.

    Science.gov (United States)

    Azerrad, Sara P; Gur-Reznik, Shirra; Heller-Grossman, Lilly; Dosoretz, Carlos G

    2014-10-01

    Among the main restrictions for the implementation of advanced oxidation processes (AOPs) for removal of micropollutants present in reverse osmosis (RO) brines of secondary effluents account the quenching performed by background organic and inorganic constituents. Natural organic matter (NOM) and soluble microbial products (SMP) are the main effluent organic matter constituents. The inorganic fraction is largely constituted by chlorides and bicarbonate alkalinity with sodium and calcium as main counterions. The quenching influence of these components, separately and their mixture, in the transformation of model compounds by UVA/TiO2 was studied applying synthetic brines solutions mimicking 2-fold concentrated RO secondary effluents brines. The results were validated using fresh RO brines. Diatrizoate (DTZ) and iopromide (IOPr) were used as model compound. They have been found to exhibit relative high resistance to oxidation process and therefore represent good markers for AOPs techniques. Under the conditions applied, oxidization of DTZ in the background of RO brines was strongly affected by quenching effects. The major contribution to quenching resulted from organic matter (≈70%) followed by bicarbonate alkalinity (≈30%). NOM displayed higher quenching than SMP in spite of its relative lower concentration. Multivalent cations, i.e., Ca(+2), were found to decrease effectiveness of the technique due to agglomeration of the catalyst. However this influence was lowered in presence of NOM. Different patterns of transformation were found for each model compound in which a delayed deiodination was observed for iopromide whereas diatrizoate oxidation paralleled deiodination. Copyright © 2014 Elsevier Ltd. All rights reserved.

  15. Petroleum

    International Nuclear Information System (INIS)

    Anon.

    2000-01-01

    Here are gathered the results of the year 1999 concerning the petroleum industry in France ('UFIP' data), the market quotations of crude oil, the prices of fuels in France and in Portugal and some news about the petroleum industry in Algeria (privatization, exploration-offshore, repurchase), in Iraq (exports, contracts with foreign companies), in Russian Federation (petroleum pipelines and oil ports constructions) and in Chad (production sharing, offshore sites discoveries). (O.M.)

  16. Kinetics of radioisotope exchange between brine and rock in a geothermal system

    International Nuclear Information System (INIS)

    Hammond, D.E.; Zukin, J.G.; Teh-Lung Ku

    1988-01-01

    A wide range of isotopes in the /sup 238/U, /sup 235/U, and /sup 232/Th decay chains was measured in geothermal brines collected from two production zones at 1898 and 3220 m in the Salton Sea Scientific Drilling Project well. High concentrations of radium, radon, and lead isotopes are generated and maintained by the input of these isotopes from solid phases into brine by both recoil and leaching processes, by the high chloride content of the brine which complexes radium and lead, and by the apparent absence of suitable unoccupied adsorption sites. In contrast, uranium, thorium, actinium, bismuth, and polonium isotopes all have low concentrations due to their efficient sorption from brine to rock. Measurements of short-lived isotopes in these decay series yield insights regarding the mechanisms controlling radioisotope exchange, and they permit estimation of rates of brine-rock interaction. For example, the /sup 228/Ac//sup 228/Ra activity ratio of 0.2 in brines indicates that the mean residence time of actinium in solution before sorption onto solid surfaces is less than 2.5 hours

  17. Petroleum Supply Monthly

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major U.S. geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  18. Effects of temperature, temperature gradients, stress, and irradiation on migration of brine inclusions in a salt repository

    International Nuclear Information System (INIS)

    Jenks, G.H.

    1979-07-01

    Available experimental and theoretical information on brine migration in bedded salt are reviewed and analyzed. The effects of temperature, thermal gradients, stress, irradiation, and pressure in a salt repository are among the factors considered. The theoretical and experimental (with KCl) results of Anthony and Cline were used to correlate and explain the available data for rates of brine migration at temperatures up to 250 0 C in naturally occurring crystals of bedded salt from Lyons and Hutchinson, Kansas. Considerations of the effects of stressing crystals of bedded salt on the migratin properties of brine inclusions within the crystals led to the conclusion that the most probable effects are a small fractional increase in the solubility of the salt within the liquid and a concomitant and equal fractional increase in the rate of the thermal gradient-induced migration of the brine. The greatest uncertainty relative to the prediction of rates of migration of brine into a waste emplacement cavity in bedded salt is associated with questions concerning the effects of the grain boundaries (within the aggregates of single crystals which comprise a bedded salt deposit) on brine migration through the deposit. The results of some of the estimates of rates and total amounts of brine inflow to HLW and SURF waste packages emplaced in bedded salt were included to illustrate the inflow volumes which might occur in a repository. The results of the brine inflow estimates for 10-year-old HLW emplaced at 150 kW/acre indicated inflow rates starting at 0.7 liter/year and totaling 12 liters at 30 years after emplacement. The results of the estimates for 10-year-old PWR SURF emplaced at 60 kW/acre indicated a constant inflow of 0.035 liter/year for the first 35 years after emplacement

  19. Modeling the morphogenesis of brine channels in sea ice.

    Science.gov (United States)

    Kutschan, B; Morawetz, K; Gemming, S

    2010-03-01

    Brine channels are formed in sea ice under certain constraints and represent a habitat of different microorganisms. The complex system depends on a number of various quantities as salinity, density, pH value, or temperature. Each quantity governs the process of brine channel formation. There exists a strong link between bulk salinity and the presence of brine drainage channels in growing ice with respect to both the horizontal and vertical planes. We develop a suitable phenomenological model for the formation of brine channels both referring to the Ginzburg-Landau theory of phase transitions as well as to the chemical basis of morphogenesis according to Turing. It is possible to conclude from the critical wave number on the size of the structure and the critical parameters. The theoretically deduced transition rates have the same magnitude as the experimental values. The model creates channels of similar size as observed experimentally. An extension of the model toward channels with different sizes is possible. The microstructure of ice determines the albedo feedback and plays therefore an important role for large-scale global circulation models.

  20. Brine migration resulting from pressure increases in a layered subsurface system

    Science.gov (United States)

    Delfs, Jens-Olaf; Nordbeck, Johannes; Bauer, Sebastian

    2016-04-01

    Brine originating from the deep subsurface impairs parts of the freshwater resources in the North German Basin. Some of the deep porous formations (esp. Trias and Jurassic) exhibit considerable storage capacities for waste fluids (CO2, brine from oil production or cavern leaching), raising concerns among water providers that this type of deep subsurface utilization might impair drinking water supplies. On the one hand, overpressures induced by fluid injections and the geothermal gradient support brine migration from deep into shallow formations. On the other hand, the rising brine is denser than the surrounding less-saline formation waters and, therefore, tends to settle down. Aim of this work is to investigate the conditions under which pressurized formation brine from deep formations can reach shallow freshwater resources. Especially, the role of intermediate porous formations between the storage formation and the groundwater is studied. For this, complex thermohaline simulations using a coupled numerical process model are necessary and performed in this study, in which fluid density depends on fluid pressure, temperature and salt content and the governing partial differential equations are coupled. The model setup is 2D and contains a hypothetic series of aquifers and barriers, each with a thickness of 200 m. Formation pressure is increased at depths of about 2000 m in proximity to a salt wall and a permeable fault. The domain size reaches up to tens of kilometers horizontally to the salt wall. The fault connects the injection formation and the freshwater aquifer such that conditions can be considered as extremely favorable for induced brine migration (worst case scenarios). Brine, heat, and salt fluxes are quantified with reference to hydraulic permeabilities, storage capacities (in terms of domain size), initial salt and heat distribution, and operation pressures. The simulations reveal the development of a stagnation point in the fault region in each

  1. Laboratory modeling, field study, and numerical simulation of bioremediation of petroleum contaminants

    International Nuclear Information System (INIS)

    Livingston, R.J.; Islam, M.R.

    1999-01-01

    Historical methods of cleaning up petroleum hydrocarbons from the vadose zone, the capillary zone, and the aquifers are not technically true cleanup technologies but rather transfer techniques. In addition, environmental engineers are realizing that the standard remediation techniques are not entirely effective in removing the hazardous material in a reasonable time frame. Long-chain hydrocarbons such as kerosene, diesel, and waste oil are particularly difficult to remediate using conventional techniques. The use of bioremediation as an alternative remediation technology is fast becoming the technique of choice among many environmental professionals. This method offers substantial benefits not found in other remediation processes. Bioremediation is very cost effective, nondestructive, relatively uncomplicated in implementing, requires non specialized equipment, and can be extremely effective in removing recalcitrant petroleum hydrocarbons. This study researched the availability of viable microbial populations in the arid climate in South Dakota. Exponential growth of the bacteria and the ability of bacteria to degrade long-chain hydrocarbons indicated that healthy populations do exist and could be used to mineralize organic hydrocarbons. Experimental results indicated that bioremediation can be effectively enhanced in landfills as well as in the subsurface using a supply of harmless nutrients. The biodegradation rate can be further enhanced with the use of edible surfactant that helped disperse the petroleum products. Also, the use of hydrogen peroxide enhanced the oxygen availability and increased the degradation rate. Interestingly, the bacterial growth rate is found to be high in difficult-to-biodegrade contaminants, such as waste oil. A numerical simulation program was also developed that describes the bacterial growth in the subsurface along with the reduction in substrate (contamination). Results from this program were found to be consistent with laboratory

  2. Cost-effective bioregeneration of nitrate-laden ion exchange brine through deliberate bicarbonate incorporation.

    Science.gov (United States)

    Li, Qi; Huang, Bin; Chen, Xin; Shi, Yi

    2015-05-15

    Bioregeneration of nitrate-laden ion exchange brine is desired to minimize its environmental impacts, but faces common challenges, i.e., enriching sufficient salt-tolerant denitrifying bacteria and stabilizing brine salinity and alkalinity for stable brine biotreatment and economically removing undesired organics derived in biotreatment. Incorporation of 0.25 M bicarbonate in 0.5 M chloride brine little affected resin regeneration but created a benign alkaline condition to favor bio-based brine regeneration. The first-quarter sulfate-mainly enriched spent brine (SB) was acidified with carbon source acetic acid for using CaCl2 at an efficiency >80% to remove sulfate. Residual Ca(2+) was limited below 2 mM by re-mixing the first-quarter and remained SB to favor denitrification. Under [Formula: see text] system buffered pH condition (8.3-8.8), nitrate was removed at 0.90 gN/L/d by hematite-enriched well-settled activated sludge (SVI 8.5 ml/g) and the biogenic alkalinity was retained as bicarbonate. The biogenic alkalinity met the need of alkalinity in removing residual Ca(2+) after sulfate removal and in CaCl2-induced CaCO3 flocculation to remove 63% of soluble organic carbon (SOC) in biotreated brine. Carbon-limited denitrification was also operated after activated sludge acclimation with sulfide to cut SOC formation during denitrification. Overall, this bicarbonate-incorporation approach, stabilizing the brine salinity and alkalinity for stable denitrification and economical removal of undesired SOC, suits long-term cost-effective brine bioregeneration. Copyright © 2015 Elsevier Ltd. All rights reserved.

  3. Euro-arab petroleum and gas relations. Perspectives and consequences of an increasing interdependence

    International Nuclear Information System (INIS)

    Anon.

    1995-01-01

    Arab countries are the most important petroleum and gas suppliers for european countries. The energy demand is certainly going to grow. From the price point of view, it seems the these ones are staying low and it does not help the petroleum production development and natural gas exports. An other point in petroleum prices is the exporting countries part is at 19% against 48% in 1984 and the consumers part spent from 35% in 1984 to 61% in 1994. The part of costs and profits of petroleum companies spent from 17% to 20%. New taxes could reduce still more the producers countries income. For natural gas, the problem of price is more crucial because a lot of gas exports projects are no more profitable at actual prices. If the major preoccupation of industrialized countries is to import petroleum at prices as low as possible, it is not sure that the question of security supply is completely and forever solved. A real cooperation between european and arab countries should answer to the need of economic development in arab countries

  4. Contribution of offshore petroleum deposits to marine food chain

    Science.gov (United States)

    Mori, S.

    2009-12-01

    Petroleum production out of offshore petroleum deposits often coincides with abundant fisheries in the world. Superposition of marine microorganism concentration distribution and offshore petroleum field distribution from various data in the literature provides to prove this coincidence. Sakhalin Island coastal regions, North Sea, Gulf of Mexico, etc. are chosen for the superpositions. Significant conformity is observed between the plankton concentration distribution and the offshore petroleum deposit distribution in all those regions. Also, most studies on the consequence of oil spills to marine eco-systems have focused mainly on hazardous marine pollution caused by spilled petroleum at high concentration in marine environment. However, some of those data clearly indicate stimulation of plankton population in properly low concentration levels of dissolved hydrocarbons and dissolved petroleum compositions. Further, increase of hydrocarbon concentration leads to its inhibition from its stimulation conditions upon crossing over a critical concentration level—a plankton stimulation/inhibition threshold concentration (SITC) of hydrocarbons. The SITC varies depending on hydrocarbon compounds, petroleum compositions, and microorganisms such as planktons. Further, petroleum composition diffusing through subterranean layers from petroleum deposits reacts with dissolved oxygen to be consumed at the ocean floor to precipitate the agglomerate suspension of hydrocarbons, leaving the sea water in a condition of oxygen depletion on the ocean floor. Such incidents are also briefly discussed.Plankton stimulation/inhibition threshold concentration of petroleum fractions

  5. A network model for characterizing brine channels in sea ice

    Science.gov (United States)

    Lieblappen, Ross M.; Kumar, Deip D.; Pauls, Scott D.; Obbard, Rachel W.

    2018-03-01

    The brine pore space in sea ice can form complex connected structures whose geometry is critical in the governance of important physical transport processes between the ocean, sea ice, and surface. Recent advances in three-dimensional imaging using X-ray micro-computed tomography have enabled the visualization and quantification of the brine network morphology and variability. Using imaging of first-year sea ice samples at in situ temperatures, we create a new mathematical network model to characterize the topology and connectivity of the brine channels. This model provides a statistical framework where we can characterize the pore networks via two parameters, depth and temperature, for use in dynamical sea ice models. Our approach advances the quantification of brine connectivity in sea ice, which can help investigations of bulk physical properties, such as fluid permeability, that are key in both global and regional sea ice models.

  6. Modeling of brine migration in halite

    International Nuclear Information System (INIS)

    Cheung, H.; Fuller, M.E.; Gaffney, E.S.

    1979-01-01

    When canisters containing radwastes are emplaced in a repository the heat produced by the decaying radwaste will cause moderate thermal gradients to develop which will cause the brine present in a halite medium (salt deposits) to accumulate around the canister. Four different models of the migration process have been reviewed to determine their suitability as a working model. One model predicts that inclusions smaller than 0.1 mm dimension probably will not migrate. The other models do not consider size as a factor. Thermal diffusion (Soret effect) is considered insignificant in three models, while in the fourth model it is added to the concentration diffusion term. The following conclusions can be made: Temperature is the most significant parameter in all models and must be known as a function of time, and distance from the canister. All four models predict about the same migration velocity for it is a given set of conditions; for 100 0 C and 1 0 C/cm thermal gradient, it is 3.0, 4.8, 5.6 and 6.4 mm/y. Diffusion of ions through the brine inclusions is the rate controlling mechanism. The difference between the thermal gradients in the liquid and in the solid should always be considered and is a function of droplet shape. The model based upon work by Nernst is easiest to use, but it predicts the lowest migration rate. The maximum volume of pure brine accumulated at the canister surface would be less than 20-40 liters in 50 years, for a canister initial thermal power of 3.5 kW.Bitterns would migrate proportionately less volume. A computer code, BRINE, was developed to make these calculations by means of any of the four models

  7. Stability of polyvinyl alcohol-coated biochar nanoparticles in brine

    Energy Technology Data Exchange (ETDEWEB)

    Griffith, Christopher, E-mail: cgriffith@utexas.edu; Daigle, Hugh [University of Texas at Austin, Department of Petroleum and Geosystems Engineering (United States)

    2017-01-15

    This paper reports on the dispersion stability of 150 nm polyvinyl alcohol coated biochar nanoparticles in brine water. Biochar is a renewable, carbon based material that is of significant interest for enhanced oil recovery operations primarily due to its wide ranging surface properties, low cost of synthesis, and low environmental toxicity. Nanoparticles used as stabilizing agents for foams (and emulsions) or in nanofluids have emerged as potential alternatives to surfactants for subsurface applications due to their improved stability at reservoir conditions. If, however, the particles are not properly designed, they are susceptible to aggregation because of the high salinity brines typical of oil and gas reservoirs. Attachment of polymers to the nanoparticle surface, through covalent bonds, provides steric stabilization, and is a necessary step. Our results show that as the graft density of polyvinyl alcohol increases, so too does the stability of nanoparticles in brine solutions. A maximum of 34 wt% of 50,000 Da polyvinyl alcohol was grafted to the particle surface, and the size of the particles was reduced from ~3500 nm (no coating) to 350 nm in brine. After 24 h, the particles had a size of ~500 nm, and after 48 h completely aggregated. 100,000 Da PVA coated at 24 wt% on the biochar particles were stable in brine for over 1 month with no change in mean particle size of ~330 nm.

  8. Petroleum

    International Nuclear Information System (INIS)

    Anon.

    2000-01-01

    Here are briefly summarized 1)the OPEC decisions and their consequences concerning the production of petroleum in the world 2)some news about the petroleum industry in Chad and in Iraq 3)some news about the new pipelines constructed or to be constructed in the world 4)some news about the LPG industry (start of a LPG extraction unit in Argentina, legislation in France for LPG vehicles) 4)and some news about the petroleum distribution in France. (O.M.)

  9. Petroleum Oxidation in Marine Microcosms by Natural Microbial Assemblages

    Science.gov (United States)

    Wardlaw, G. D.; Reddy, C. M.; Nelson, R. K.; Ehrhardt, C. J.; Valentine, D. L.

    2006-12-01

    Millions of gallons of petroleum are emitted into marine environments each year and the oxidation of this oil by microbes is an important mechanism for mediating toxicity. In terms of quantity, petroleum is the most abundant organic pollutant impacting marine environments today. Recent advances in chromatography have led to the development of comprehensive two-dimensional gas chromatography (GC &GC). The acronym, GC GC, is used because orthogonal gas chromatographic separations are achieved in both analytical dimensions by using stationary phases with varying partitioning abilities and selectivity. This novel method has greatly expanded the analytical window of petroleum hydrocarbons and was used to track the loss of petroleum hydrocarbons in aerobic marine microcosm experiments. Sediment microcosms were composed of seawater and sediment collected from the Coal Oil Point (COP) seep field off the coast of Santa Barbara, CA. Oil collected directly from the reservoir underlying the seep field was added to each microcosm, and samples were incubated for one year. Net metabolism was tracked by quantifying oxygen consumption and carbon dioxide production. The loss of petroleum components was tracked with GC GC, whereas the bacterial and archaeal community structures were tracked using T-RFLP. Results of these incubation studies will be presented.

  10. Determination of pollutant elements and heavy metals in petroleum sludge and scale at Heglig field Sudan

    International Nuclear Information System (INIS)

    Amir, N. T.

    2012-02-01

    The release of pollutant metals from petroleum industry in to ecosystems represents a serious hazard for the biosphere, because of their toxicity. The objective of this study was to determine the levels of some elements in petroleum sludge and scales collected from petroleum production area in Heglig oil field located in South Kordofan State. The concentration of Ca, Fe, V, Mn,Ni, Cu, Zn, Cs, Sr, Zr, Y and Pb in sludge and scale samples have been determined using energy dispersive x-ray fluorescence (EDXRF) equipped with a point source of 1 09C d. The concentration of Ca and Fe in scale samples were found to fall in range of 15,49-23.28% and 0.98-5.13%, respectively. The a verge elemental concentrations of Ti, Mn, Ni, Cu, Zn, Sr,Y, and Pb in scale samples were 2917.8, 567.74, 23.21, 23.05, 101.67, 31.38, 177.06 and 24.12 (mg/kg), respectively. The concentrations of Ca and Fe in sludge samples ranged from 1.98-8.82% and 0.71-5.19%, respectively and the a verge elemental concentrations of Cs, V, Mn,Cu, Zn, Pb, Sr, Y and Zr were 7.44, 92,59, 557.36, 7.67, 162.72,28.67, 65.02, 45.64 and 52.15 (mg/kg), respectively. Correlation analysis revealed lock of any significant correlation between elemental concentrations in sludge and scales. (Author)

  11. Preliminary fingerprinting analysis of Alberta oil sands and related petroleum products

    International Nuclear Information System (INIS)

    Yang, C.; Wang, Z.D.; Hollebone, B.; Brown, C.E.; Yang, Z.Y.; Landriault, M.; Fieldhouse, B.

    2009-01-01

    This paper reported on a study that presented a preliminary quantitative chemical characterization of Alberta oil sands and many other related Alberta oils such as oil sand bitumen, Cold Lake bitumen, Albian heavy synthetic crude, and Alberta Mixed sweet blend. The rapid increase in production of the Alberta oil sands has resulted in unprecedented environmental concern. The mining, extraction and production of oil sands such resulted in huge consumption of water resources, huge emission of greenhouse gas and large number of tailings ponds. In addition, accidental spills in the transportation and usage of oil sands will potentially cause considerable impact on the environment. It is therefore essential to have the ability to characterize Alberta oil sands and their oil products. The specific chemical properties of the oil sands bitumen must be known. Therefore, this study collected quantitative data on the concentration and distribution profiles of target compounds in Alberta oil sands and its petroleum products. The chemical fingerprints of 5 Alberta oil sands and their related petroleum products were studied using gas chromatography/flame ionization detection (GC/FID) and gas chromatography/mass spectrometry (GC/MS). The characterized hydrocarbons were n-alkanes; target alkylated PAHs and other EPA priority PAHs; biomarker terpanes and steranes; and bicyclic sesquiterpanes. The information acquired during this study will provide the basis for oil-oil correlation and differentiation in future environmental applications relevant to oil sands. 24 refs., 6 tabs., 4 figs.

  12. Solubility of Nd in brine

    International Nuclear Information System (INIS)

    Khalili, F.I.; Symeopoulos, V.; Chen, J.F.; Choppin, G.R.

    1994-01-01

    The solubility of Nd(III) has been measured at 23±3 C in a synthetic brine at pcH 6.4, 8.4, 10.4 and 12.4. The brine consisted predominantly of (Na+K)Cl and MgCl 2 with an ionic strength of 7.8 M (9.4 m) a solid compound of Nd(III) at each pcH was assigned from X-ray diffraction patterns. The log values of the experimental solubilities decrease fomr -3 at pcH 6.4 to -5.8 at pcH 8.4; at pcH 10.4 and 12.4 the solubility was below the detection limit of -7.5. The experimental solubility does not follow closely the variation with pcH estimated from modeling of the species in solution in equilibrium with the Nd solid using S.I.T. (orig.)

  13. Managing the visual effects of outer continental shelf and other petroleum-related coastal development

    Science.gov (United States)

    Philip A. Marcus; Ethan T. Smith

    1979-01-01

    Five petroleum-related facilities often sited in the coastal zone during development of Outer Continental oil and gas can change the visual appearance of coastal areas. These facilities are service bases, platform fabrication yards, marine terminals and associated storage facilities, oil and gas processing facilities, and liquified natural gas terminals. Examples of...

  14. Comparison of methods used to estimate conventional undiscovered petroleum resources: World examples

    Science.gov (United States)

    Ahlbrandt, T.S.; Klett, T.R.

    2005-01-01

    Various methods for assessing undiscovered oil, natural gas, and natural gas liquid resources were compared in support of the USGS World Petroleum Assessment 2000. Discovery process, linear fractal, parabolic fractal, engineering estimates, PETRIMES, Delphi, and the USGS 2000 methods were compared. Three comparisons of these methods were made in: (1) the Neuquen Basin province, Argentina (different assessors, same input data); (2) provinces in North Africa, Oman, and Yemen (same assessors, different methods); and (3) the Arabian Peninsula, Arabian (Persian) Gulf, and North Sea (different assessors, different methods). A fourth comparison (same assessors, same assessment methods but different geologic models), between results from structural and stratigraphic assessment units in the North Sea used only the USGS 2000 method, and hence compared the type of assessment unit rather than the method. In comparing methods, differences arise from inherent differences in assumptions regarding: (1) the underlying distribution of the parent field population (all fields, discovered and undiscovered), (2) the population of fields being estimated; that is, the entire parent distribution or the undiscovered resource distribution, (3) inclusion or exclusion of large outlier fields; (4) inclusion or exclusion of field (reserve) growth, (5) deterministic or probabilistic models, (6) data requirements, and (7) scale and time frame of the assessment. Discovery process, Delphi subjective consensus, and the USGS 2000 method yield comparable results because similar procedures are employed. In mature areas such as the Neuquen Basin province in Argentina, the linear and parabolic fractal and engineering methods were conservative compared to the other five methods and relative to new reserve additions there since 1995. The PETRIMES method gave the most optimistic estimates in the Neuquen Basin. In less mature areas, the linear fractal method yielded larger estimates relative to other methods

  15. Petroleum and international policy; Petrole et politique internationale

    Energy Technology Data Exchange (ETDEWEB)

    Pertuzio, A

    2002-07-01

    To illustrate the relation between the petroleum and the international policy, the author presents the place of the petroleum industry in the international relations by an analysis of the historical aspects, the states and international organizations interventions and the prices evolution. (A.L.B.)

  16. Relationships between stratigraphy, deformation and thermal history in sedimentary basins. Impact of geodynamic concepts in petroleum exploration

    International Nuclear Information System (INIS)

    Sarmiento, Luis Fernando

    2002-01-01

    The natural processes that generate petroleum accumulations in a sedimentary basin require several ingredients: (1) the petroleum system elements: source, reservoir, seal and overburden rocks, which are the result of sedimentation processes in a subsiding basin; (2) petroleum traps, which in many cases are the result of deformation and (3) heat to convert suitable organic matter into petroleum. Although these different phenomena are considered independent at the scale of an oil field, at the lithosphere scale thermal phenomena, (2) vertical movements of the earth surface responsible for sedimentation and erosion and (3) tectonic deformation are not independent phenomena, physical quantitative laws intimately relate them. These mutual inter relationships are useful in petroleum exploration to predict one factor having knowledge of the others. Applications of these concepts can contribute to understand the tectonic history of complex areas, such as the Colombian sedimentary basins and reduce exploration risk

  17. Petroleum and natural gas economy in Arab Countries, in Angola, Iran, Nigeria, Tanzania and Zaire

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    This paper gives informations on petroleum and natural gas industry, petroleum market and prices, trade and contracts, prospection and production. The possible return of Iraq on the petroleum market has an influence on petroleum prices. In Algeria, Sonatrach will deliver 2.5 milliards m 3 to Portugal through the Maghreb-Europe gas pipeline. In Tunisia, a petroleum exploration permit has been attributed to Atlantic Richfield Company and Miskar natural gas field would come into production in 1995. In Saudi Arabia, Saudi Aramco has bought all the petroleum refining and distribution interests of the Saudi Arabian Marketing and Refining Company and Petromin Company and now Saudi Aramco is become a national integrated petroleum company. Petroleum exploration is going on in Caspian sea (Iran), six new oil fields have come into production in the Deir ez-Zor and Ash Sham permits (Syria) and petroleum exploration contracts have been signed in Angola, Nigeria and Zaire. In Egypt, the growth of natural gas consumption gives an indication upon the future growing deficit

  18. Brine migrations in the Athabasca Basin platform, alteration and associated fluid-rock exchanges

    International Nuclear Information System (INIS)

    Mercadier, J.; Cathelineau, M.; Richard, A.; Boiron, M.Ch.; Cuney, M.; Milesi, J.P.

    2009-01-01

    Uranium deposits of Athabasca Basin (Saskatchewan, Canada) are considered as the richest in the world. They result from massive percolation of basin brines in the underlying platform. The authors describe the brine movements and how structures and micro-fractures promoted this percolation until very important depths (hundreds of meters under the discordance), and their chemical modifications as they interacted with platform rocks, thus promoting the transformation of an initially sodic brine into a uranium-enriched calcic brine which is essential to the formation of discordance-type deposit

  19. Domal salt brine migration experiments at Avery Island, Louisiana

    International Nuclear Information System (INIS)

    Krause, W.B.; Gnirk, P.F.

    1981-01-01

    Three in-situ brine migration experiments were performed in domal salt in the Avery Island mine located in southwestern Louisiana. The primary measurements included temperature, moisture collection, and pre- and post-test permeability at the experimental sites. Experimental data are discussed and compared with calculations based on the single-crystal brine migration theory. Comparisons indicate reasonable agreement between experiment and theory

  20. Radiation chemistry of salt-mine brines and hydrates

    International Nuclear Information System (INIS)

    Jenks, G.H.; Walton, J.R.; Bronstein, H.R.; Baes, C.F. Jr.

    1981-07-01

    Certain aspects of the radiation chemistry of NaCl-saturated MgCl 2 solutions and MgCl 2 hydrates at temperatures in the range of 30 to 180 0 C were investigated through experiments. A principal objective was to establish the values for the yields of H 2 [G(H 2 )] and accompanying oxidants in the gamma-ray radiolysis of concentrated brines that might occur in waste repositories in salt. We concluded that G(H 2 ) from gamma-irradiated brine solution into a simultaneously irradiated, deaerated atmosphere above the solution is between 0.48 and 0.49 over most of the range 30 to 143 0 C. The yield is probably somewhat lower at the lower end of this range, averaging 0.44 at 30 to 45 0 C. Changes in the relative amounts of MgCl 2 and NaCl in the NaCl-saturated solutions have negligible effects on the yield. The yield of O 2 into the same atmosphere averages 0.13, independent of the temperature and brine composition, showing that only about 50% of the radiolytic oxidant that was formed along with the H 2 was present as O 2 . We did not identify the species that compose the remainder of the oxidant. We concluded that the yield of H 2 from a gamma-irradiated brine solution into a simultaneously irradiated atmosphere containing 5 to 8% air in He may be greater than the yield in deaerated systems by amounts ranging from 0% for temperatures of 73 to 85 0 C, to about 30 and 40% for temperatures in the ranges 100 to 143 0 C and 30 to 45 0 C, respectively. We did not establish the mechanism whereby the air affected the yields of H 2 and O 2 . The values found in this work for G(H 2 ) in deaerated systems are in approximate agreement with the value of 0.44 for the gamma-irradiation yield of H 2 in pure H 2 O at room temperature. They are also in agreement with the values predicted by extrapolation from the findings of previous researchers for the value for G(H 2 ) in 2 M NaCl solutions at room temperature

  1. Fate of Brine Applied to Unpaved Roads at a Radioactive Waste Subsurface Disposal Area

    International Nuclear Information System (INIS)

    Larry C. Hull; Carolyn W. Bishop

    2004-01-01

    Between 1984 and 1993, MgCl 2 brine was used to suppress dust on unpaved roads at a radioactive waste subsurface disposal area. Because Cl - might enhance corrosion of buried metals in the waste, we investigated the distribution and fate of Cl - in the vadose zone using pore water samples collected from suction lysimeters and soluble salt concentrations extracted from sediment samples. The Cl/Br mass ratio and the total dissolved Cl - concentration of pore water show that brine contamination occurs primarily within 13 m of treated roads, but can extend as much as 30 m laterally in near-surface sedimentary deposits. Within the deep vadose zone, which consists of interlayered basalt lava flows and sedimentary interbeds, brine has moved up to 110 m laterally. This lateral migration suggests formation of perched water and horizontal transport during periods of high recharge. In a few locations, brine migrated to depths of 67 m within 3 to 5 yr. Elevated Cl - concentrations were found to depths of 2 m in roadbed material. In drainage ditches along roads, where runoff accumulates and recharge of surface water is high, Cl - was flushed from the sediments in 3 to 4 yr. In areas of lower recharge, Cl - remained in the sediments after 5 yr. Vertical brine movement is directly related to surface recharge through sediments. The distribution of Cl - in pore water and sediments is consistent with estimates of vadose zone residence times and spatial distribution of surface water recharge from other investigations at the subsurface disposal area

  2. Alcohol Brine Freezing of Japanese Horse Mackerel (Trachurus japonicus) for Raw Consumption

    Science.gov (United States)

    Maeda, Toshimichi; Yuki, Atsuhiko; Sakurai, Hiroshi; Watanabe, Koichiro; Itoh, Nobuo; Inui, Etsuro; Seike, Kazunori; Mizukami, Yoichi; Fukuda, Yutaka; Harada, Kazuki

    In order to test the possible application of alcohol brine freezing to Japanese horse mackerel (Trachurus japonicus) for raw consumption, the quality and taste of fish frozen by direct immersion in 60% ethanol brine at -20, -25 and -30°C was compared with those by air freezing and fresh fish without freezing. Cracks were not found during the freezing. Smell of ethanol did not remain. K value, an indicator of freshness, of fish frozen in alcohol brine was less than 8.3%, which was at the same level as those by air freezing and fresh fish. Oxidation of lipid was at the same level as air freezing does, and lower than that of fresh fish. The pH of fish frozen in alcohol brine at -25 and -30°C was 6.5 and 6.6, respectively, which were higher than that by air freezing and that of fresh fish. Fish frozen in alcohol brine was better than that by air and at the same level as fresh fish in total evaluation of sensory tests. These results show that the alcohol brine freezing is superior to air freezing, and fish frozen in alcohol brine can be a material for raw consumption. The methods of thawing in tap water, cold water, refrigerator, and at room temperature were compared. Thawing in tap water is considered to be convenient due to the short thaw time and the quality of thawed fish that was best among the methods.

  3. Experimental Study of Cement - Sandstone/Shale - Brine - CO2 Interactions.

    Science.gov (United States)

    Carroll, Susan A; McNab, Walt W; Torres, Sharon C

    2011-11-11

    Reactive-transport simulation is a tool that is being used to estimate long-term trapping of CO2, and wellbore and cap rock integrity for geologic CO2 storage. We reacted end member components of a heterolithic sandstone and shale unit that forms the upper section of the In Salah Gas Project carbon storage reservoir in Krechba, Algeria with supercritical CO2, brine, and with/without cement at reservoir conditions to develop experimentally constrained geochemical models for use in reactive transport simulations. We observe marked changes in solution composition when CO2 reacted with cement, sandstone, and shale components at reservoir conditions. The geochemical model for the reaction of sandstone and shale with CO2 and brine is a simple one in which albite, chlorite, illite and carbonate minerals partially dissolve and boehmite, smectite, and amorphous silica precipitate. The geochemical model for the wellbore environment is also fairly simple, in which alkaline cements and rock react with CO2-rich brines to form an Fe containing calcite, amorphous silica, smectite and boehmite or amorphous Al(OH)3. Our research shows that relatively simple geochemical models can describe the dominant reactions that are likely to occur when CO2 is stored in deep saline aquifers sealed with overlying shale cap rocks, as well as the dominant reactions for cement carbonation at the wellbore interface.

  4. Assessment of brine migration risks along vertical pathways due to CO2 injection

    Science.gov (United States)

    Kissinger, Alexander; Class, Holger

    2015-04-01

    Global climate change, shortage of resources and the growing usage of renewable energy sources has lead to a growing demand for the utilization of subsurface systems. Among these competing uses are Carbon Capture and Storage (CCS), geothermal energy, nuclear waste disposal, 'renewable' methane or hydrogen storage as well as the ongoing production of fossil resources like oil, gas and coal. Additionally, these technologies may also create conflicts with essential public interests such as water supply. For example, the injection of CO2 into the subsurface causes an increase in pressure reaching far beyond the actual radius of influence of the CO2 plume, potentially leading to large amounts of displaced salt water. In this work we focus on the large scale impacts of CO2 storage on brine migration but the methodology and the obtained results may also apply to other fields like waste water disposal, where large amounts of fluid are injected into the subsurface. In contrast to modeling on the reservoir scale the spatial scale required for this work is much larger in both vertical and lateral direction, as the regional hydrogeology has to be considered. Structures such as fault zones, hydrogeological windows in the Rupelian clay or salt domes are considered as potential pathways for displaced fluids into shallow systems and their influence has to be taken into account. We put the focus of our investigations on the latter type of scenario, since there is still a poor understanding of the role that salt diapirs would play in CO2 storage projects. As there is hardly any field data available on this scale, we compare different levels of model complexity in order to identify the relevant processes for brine displacement and simplify the modeling process wherever possible, for example brine injection vs. CO2 injection, simplified geometries vs. the complex formation geometry and the role of salt induced density differences on flow. Further we investigate the impact of the

  5. Distribution of Cathepsin D Activity between Lysosomes and a Soluble Fraction of Marinating Brine.

    Science.gov (United States)

    Szymczak, Mariusz

    2016-08-01

    This paper is the first ever to describe the phenomenon of bimodal distribution of cathepsin D in the lysosomal and soluble fractions of brine left after herring marinating. Up to 2 times higher cathepsin D activity was observed in the lysosome fraction. Activity of cathepsin D in brine increased according to the logarithmic function during low frequency-high power ultrasounds treatment or according to the linear function after multiple freezing-thawing of brine. Activity enhancement was achieved only in the brine devoid of lipids and suspension. Study results show also that measurement of lysosomal cathepsin D activity in the marinating brine requires also determining cathepsin E activity. Decreasing pore size of microfilter from 2.7 to 0.3 μm significantly reduced the lysosome content in the brine. The presence of lysosomes and the possibility of their separation as well as the likely release of cathepsins shall be considered during industrial application of the marinating brine, as new cathepsins preparations in fish and meat technology. © 2016 Institute of Food Technologists®

  6. Laboratory modeling, field study, and numerical simulation of bioremediation of petroleum contaminants

    International Nuclear Information System (INIS)

    Livingston, R.J.; Islam, M.R.

    1999-01-01

    The use of bioremediation as an alternative remediation technology is fast becoming the technique of choice among many environmental professionals. This method offers substantial benefits not found in other remediation processes. Bioremediation is very cost effective, nondestructive, relatively uncomplicated in implementing, requires nonspecialized equipment, and can be extremely effective in removing recalcitrant petroleum hydrocarbons. This study researched the availability of viable microbial populations in the arid climate in South Dakota. Exponential growth of the bacteria and the ability of bacteria to degrade long-chain hydrocarbons indicated that healthy populations do exist and could be used to mineralize organic hydrocarbons. Experimental results indicated that bioremediation can be effectively enhanced in landfills as well as in the subsurface using a supply of harmless nutrients. The biodegradation rate can be further enhanced with the use of edible surfactant that helped disperse the petroleum products. Also, the use of hydrogen peroxide enhanced the oxygen availability and increased the degradation rate. Interestingly, the bacterial growth rate was found to be high in difficult-to-biodegrade contaminants, such as waste oil. A numerical simulation program was also developed that describes the bacterial growth in the subsurface along with the reduction in substrate (contamination). Results from this program were found to be consistent with laboratory results

  7. A carbon inventory for Orca Basin brines and sediments

    International Nuclear Information System (INIS)

    Sackett, W.M.; Brooks, J.M.; Bernard, B.B.; Schwab, C.R.; Chung, H.; Parker, R.A.

    1979-01-01

    Orca Basin, an intraslope depression at a depth of about 2400 m on the continental slope of the north-central Gulf of Mexico, contains an anoxic, hypersaline brine similar to composition to those reported in the Red Sea. Concentrations and stable carbon isotope compositions of various inorganic and organic carbon species have been determined on the brine and sediments in order to gain an understanding of the origin and cycling of carbon in this unique environment. ΣCO 2 in the brine (55 mg C/l) is about twice seawater with delta 13 C sub(PDB)=-16.4per thousand and Δ 14 C=-501per thousand. CH 4 has a concentration of 12 mg C/l and delta 13 C=-73.5per thousand. Dissolved and particulate organic carbon concentrations are seven times higher and have delta 13 C values several permil different than the overlying seawater, ΣCO 2 and CH 4 in the interstitial waters are considerably higher in concentrations and isotropically light than the overlying brine. Solution of near-surface salt deposits by seawater with subsequent microbial production and consumption of methane can be used to explain most of the data. (Auth.)

  8. Freezing of perchlorate and chloride brines under Mars-relevant conditions

    Science.gov (United States)

    Primm, K. M.; Gough, R. V.; Chevrier, V. F.; Tolbert, M. A.

    2017-09-01

    Perchlorate and chloride salts on Mars could readily absorb water vapor and deliquesce into aqueous solutions. The deliquescence relative humidity (RH) as well as the efflorescence (recrystallization) RH of several Mars-relevant salts are now well known; however, the conditions that could cause a brine to freeze are not well established. It is often assumed that ice formation will occur whenever the saturation with respect to ice, Sice, of the system is greater than or equal to unity; however, ice nucleation is often hindered due to a kinetic barrier. For ice to form, a critical cluster of the ice crystal must first be achieved, often requiring Sice > 1. Here we use a Raman microscope and an environmental cell to examine the RH and temperature conditions required for Mg(ClO4)2 and MgCl2 brines to freeze into ice. By examining the salt phase present both optically and spectrally under different low temperature conditions, it is found that both salts exhibit Sice values much greater than unity, meaning that supersaturation readily occurs and brines can persist under conditions previously thought to lead to freezing. The RH range of ice formation for Mg(ClO4)2 from 218 to 245 K is 83-95%, respectively, corresponding to Sice = 1.30-1.54. The RH of ice formation for MgCl2 ranges from 80 to 100% for temperatures between 221 and 252 K, corresponding to Sice = 1.30-1.35. In addition to ice nucleation, the deliquescence and efflorescence relative humidity values for MgCl2 were determined. Two hydrates for MgCl2 were observed, and exhibited different deliquescence relative humidity (DRH) values. The DRH for MgCl2·4H2O was found to be 12.8 ± 0.3% at 243 K with slightly increasing DRH as temperature decreased. The DRH for MgCl2·6H2O was found to be 31.3 ± 0.6% at 242 K with little temperature dependence. The DRH of MgCl2·6H2O was measured below the previously reported eutectic, 240 K, suggesting that the eutectic might be incorrect or that there is a different relevant

  9. Threshold temperature gradient effect on migration of brine inclusions in salt

    International Nuclear Information System (INIS)

    Pigford, T.H.

    1987-01-01

    Theories of the migration of brine inclusions in salt were interpreted as simple physical processes, and theories by Russian and US workers were shown to yield the same results. The migration theory was used to predict threshold temperature gradients below which migration of brine inclusions should not occur. The predicted threshold gradients were compared with the temperature gradients expected at the Waste Isolation Pilot Plant in New Mexico. The theory of threshold gradients helps explain the existence of brine inclusions in natural salt deposits

  10. Scanning electron microscope observations of brine shrimp larvae from space shuttle experiments

    Science.gov (United States)

    DeBell, L.; Paulsen, A.; Spooner, B.

    1992-01-01

    Brine shrimp are encysted as gastrula stage embryos, and may remain dehydrated and encysted for years without compromising their viability. This aspect of brine shrimp biology is desirable for studying development of animals during space shuttle flight, as cysts placed aboard a spacecraft may be rehydrated at the convenience of an astronaut, guaranteeing that subsequent brine shrimp development occurs only on orbit and not on the pad during launch delays. Brine shrimp cysts placed in 5 ml syringes were rehydrated with salt water and hatched during a 9 day space shuttle mission. Subsequent larvae developed to the 8th larval stage in the sealed syringes. We studied the morphogenesis of the brine shrimp larvae and found the larvae from the space shuttle experiments similar in rate of growth and extent of development, to larvae grown in sealed syringes on the ground. Extensive differentiation and development of embryos and larvae can occur in a microgravity environment.

  11. The use of field redox measurements in assessing remediation of ground water containing petroleum hydrocarbons and chlorinated organic compounds

    International Nuclear Information System (INIS)

    Warner, S.D.; Gallinatti, J.D.; Honniball, J.H.

    1995-01-01

    Field measurements of the reduction-oxidation (redox) condition of ground water were used to assess the effects of in situ remediation of ground water affected by petroleum hydrocarbons and chlorinated organic compounds at multiple sites in northern California. The redox condition of ground water, traditionally measured quickly and inexpensively using a meter that measures electrode potential (Eh), is a valuable parameter by which to assess the conditions that affect the relative stability of various chemicals in ground water. Although not specific to a given redox couple measurements obtained using the traditional Eh meter give a sense of the relative tendency for a ground water to be reducing or oxidizing by providing a measurement of the system Eh. Two cases demonstrate the use of ground water Eh measurements in assessing the effects of in situ ground water remediation. In the first case, ground water affected by petroleum hydrocarbons-gasoline (TPHg), and benzene, toluene, ethylbenzene, and xylenes (BTEX) (ambient Eh of -100 to +100 millivolts [mv]) was treated by injecting hydrogen peroxide to supply oxygen to the subsurface environment and stimulate microbial activity. The second case involved remediation of ground water containing chlorinated organic compounds. In this case, a subsurface permeable ground water treatment wall containing granular iron was installed across the flow path of the affected ground water. The in situ chemical treatment, which successfully dechlorinates compounds such as trichloroethylene, 1,2-dichloroethylene, and vinyl chloride, caused reducing conditions in the ground water, which resulted in the decrease in ground water Eh from am ambient reading of about -50 mv to about -400 mv

  12. Treatment and Remediation of Petroleum-Contaminated Soils Using Selective Ornamental Plants

    OpenAIRE

    Liu, Rui; Jadeja, Rajendrasinh N.; Zhou, Qixing; Liu, Zhe

    2012-01-01

    Pot-culture experiments were carried out to assess the phytoremediation potential of 14 ornamental plants in weathered petroleum-contaminated soil, which was collected in the Shengli Oil Field, one of the biggest oil fields in China, by examining their impact on the degradation potential of total petroleum hydrocarbons (TPHs) and its composition. Results showed Gaillardia aristata, Echinacea purpurea, Fawn (Festuca arundinacea Schreb), Fire Phoenix (a combined F. arundinacea), and Medicago sa...

  13. Waste isolation pilot plant performance assessment: Radionuclide release sensitivity to diminished brine and gas flows to/from transuranic waste disposal areas

    Energy Technology Data Exchange (ETDEWEB)

    Day, Brad A.; Camphouse, R. C.; Zeitler, Todd R. [Sandia National Laboratories, Carlsbad (United States)

    2017-03-15

    Waste Isolation Pilot Plant repository releases are evaluated through the application of modified parameters to simulate accelerated creep closure, include capillary pressure effects on relative permeability, and increase brine and gas saturation in the operations and experimental (OPS/EXP) areas. The modifications to the repository model result in increased pressures and decreased brine saturations in waste areas and increased pressures and brine saturations in the OPS/EXP areas. Brine flows up the borehole during a hypothetical drilling intrusion are nearly identical and brine flows up the shaft are decreased. The modified parameters essentially halt the flow of gas from the southern waste areas to the northern nonwaste areas, except as transported through the marker beds and anhydrite layers. The combination of slightly increased waste region pressures and very slightly decreased brine saturations result in a modest increase in spallings and no significant effect on direct brine releases, with total releases from the Culebra and cutting and caving releases unaffected. Overall, the effects on total high-probability mean releases from the repository are insignificant, with total low-probability mean releases minimally increased. It is concluded that the modified OPS/EXP area parameters have an insignificant effect on the prediction of total releases.

  14. Observations of brine drainage networks and microstructure of first-year sea ice

    Science.gov (United States)

    Cole, D. M.; Shapiro, L. H.

    1998-09-01

    Brine drainage networks and the microstructure of first-year sea ice have been examined at two locations near Barrow, northern Alaska. A method for obtaining full-depth sections of ice sheets up to 1.8 m thick is presented and shown to provide information on the spatial distribution and geometry of brine drainage networks on a scale of meters. A number of such sections from the two test sites are presented which reveal a greater variety of main channel and side branch configurations than is typically observed in ice grown in the laboratory. Vertical and horizontal micrographs and thin section photographs were obtained in November 1993, and March and May 1994 at a test site in the relatively protected Elson Lagoon. The resulting time series of photographic records provide detailed information on the size, shape, and spatial distribution of the brine- and gas-filled inclusions and a means to quantify their size and shape changes with time. An example of the changes with time in inclusion sizes and aspect ratios in the vertical and horizontal directions for a depth of 0.2 m, with a given thermal history is also presented.

  15. Study of thermal-gradient-induced migration of brine inclusions in salt. Final report

    International Nuclear Information System (INIS)

    Olander, D.R.

    1984-08-01

    Natural salt deposits, which are being considered for high-level waste disposal, contain a small volume fraction of water in the form of brine inclusions distributed throughout the salt. Radioactive decay heating of the nuclear wastes will impose a temperature gradient on the surrounding salt which mobilizes the brine inclusions. Inclusions filled completely with brine (the all-liquid inclusions) migrate up the temperature gradient and eventually accumulate brine near the buried waste forms. The brine may slowly corrode or degrade the waste forms, which is undesirable. Therefore it is important to consider the migration of brine inclusions in salt under imposed temperature gradients to properly evaluate the performance of a future salt repository for nuclear wastes. The migration velocities of the inclusions were found to be dependent on temperature, temperature gradient, and inclusion shape and size. The velocities were also dictated by the interfacial mass transfer resistance at brine/solid interface. This interfacial resistance depends on the dislocation density in the crystal, which in turn, depends on the axial compressive loading of the crystal. At low axial loads, the dependence between the velocity and temperature gradient is nonlinear. At high axial loads, the interfacial resistance is reduced and the migration velocity depends linearly on the temperature gradient. All-liquid inclusions filled with mixed brines were also studied. For gas-liquid inclusions, helium, air and argon were compared. Migration studies were also conducted on single crystallites of natural salt as well as in polycrystalline natural salt samples. The behavior of the inclusions at large-ange grain boundaries was observed

  16. Study of thermal-gradient-induced migration of brine inclusions in salt. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Olander, D.R.

    1984-08-01

    Natural salt deposits, which are being considered for high-level waste disposal, contain a small volume fraction of water in the form of brine inclusions distributed throughout the salt. Radioactive decay heating of the nuclear wastes will impose a temperature gradient on the surrounding salt which mobilizes the brine inclusions. Inclusions filled completely with brine (the all-liquid inclusions) migrate up the temperature gradient and eventually accumulate brine near the buried waste forms. The brine may slowly corrode or degrade the waste forms, which is undesirable. Therefore it is important to consider the migration of brine inclusions in salt under imposed temperature gradients to properly evaluate the performance of a future salt repository for nuclear wastes. The migration velocities of the inclusions were found to be dependent on temperature, temperature gradient, and inclusion shape and size. The velocities were also dictated by the interfacial mass transfer resistance at brine/solid interface. This interfacial resistance depends on the dislocation density in the crystal, which in turn, depends on the axial compressive loading of the crystal. At low axial loads, the dependence between the velocity and temperature gradient is nonlinear. At high axial loads, the interfacial resistance is reduced and the migration velocity depends linearly on the temperature gradient. All-liquid inclusions filled with mixed brines were also studied. For gas-liquid inclusions, helium, air and argon were compared. Migration studies were also conducted on single crystallites of natural salt as well as in polycrystalline natural salt samples. The behavior of the inclusions at large-ange grain boundaries was observed.

  17. Enhanced Brine Dewatering System, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The purpose of the Enhanced Brine Dewatering System (EBDS) is to provide an easily scalable means of completely recovering usable water from byproducts created by...

  18. Enhanced Brine Dewatering System, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — The purpose of the Enhanced Brine Dewatering System (EBDS) is to provide a scalable means of completely recovering usable water from byproducts created by reverse...

  19. 46 CFR 58.16-7 - Use of liquefied petroleum gas.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Use of liquefied petroleum gas. 58.16-7 Section 58.16-7... MACHINERY AND RELATED SYSTEMS Liquefied Petroleum Gases for Cooking and Heating § 58.16-7 Use of liquefied petroleum gas. (a) Cooking equipment using liquefied petroleum gas on vessels of 100 gross tons or more that...

  20. Evaluation and analysis of underground brine resources in the southern coastal area of Laizhou Bay

    Science.gov (United States)

    Tian, M.; Zhu, H. T.; Feng, J.; Zhao, Q. S.

    2016-08-01

    The southern coastal districts of Laizhou Bay are some of the most important areas for underground brine exploitation in Shandong Province. Recently, these areas have been gradually developed by the underground brine mining industry. Such economic interest has led to brine exploitation so that underground brine resources are running out. Based on this phenomenon, this study describes the supply, runoff and draining conditions of the area by collecting and organizing the background information of the studied area. Hydrogeological parameters are then calculated according to pumping tests, and the amount of sustainable resources in the coastal areas of the Southern Bank of Laizhou Bay are then calculated based on the uniform distribution of wells. Under the circumstances of underground brine mining, the exploitation potential of the underground brine is evaluated in accordance with the calculation results of exploitation quantum. Finally, suggestions are provided for the sustainable exploitation of underground brine in the area.

  1. Comparative analysis of petroleum exploration contracts

    International Nuclear Information System (INIS)

    1996-01-01

    A principal mandate of the UNCTAD's Division on Transnational Corporations and Investment (DTCI) is to provide advisory and training services to requesting Governments aimed at strengthening their capabilities in dealing with the whole range of issues which arise in relationships between the Governments of host countries and transnational corporations (TNCs) in any natural resource, manufacturing or service sector. One of the areas in which DTCI has assisted many Governments and has accumulated considerable knowledge and experience is on matters related to the involvement of TNCs in the exploration, development and production of national petroleum resources. In this context, DTCI has provided advisory and training services related to formulating or reviewing national petroleum policies, laws and regulations, including taxation in the petroleum sector; assessing the merits of alternative forms of contractual arrangements taking into account national objectives and resources; formulating or reviewing bidding arrangements and procedures; drafting or reviewing model contracts and undertaking related economic and computer analyses; evaluating the economic, financial, legal and operational aspects of specific proposed contractual arrangements with TNCs; evaluating bids received from TNCs M the context of specific projects; preparing for negotiation with TNCs, including the formulation of negotiating positions and strategies; and formulating or reviewing legislative, institutional and other arrangements related to the establishment, functions and operation of national petroleum companies. The objective of the present paper is to assist policy-makers, especially in developing countries, in taking full advantage of the changing and increasingly complex forms of relationship evolving between host Governments and TNCs in the petroleum sector. The paper takes into account the policies and arrangements adopted by Governments in their dealings with TNCs, as well as DTCI's own

  2. Place of petroleum in the U. K. fuel market. [In relation to electricity, gas, and coal

    Energy Technology Data Exchange (ETDEWEB)

    Nicolaou, G B

    1977-06-01

    An attempt is made to study the interaction process that occurs between petroleum products and the remainder of the fuel market. Petroleum competes with electricity, gas, and coal as a source of fuel, and an assessment is made of the demand elasticities of its place in the fuel market. In the U.K. fuel market the question is to what extent petroleum is a substitute or complement to the others. Petroleum consumption constituted 25 percent in 1960 of the total fuel consumption and has grown constantly since. The extent to which it changes depends upon its close substitutes. Which out of gas, coal, and electricity is, in fact, the closest substitute for petroleum; is it sensitive to price or to other things. In order to attempt to answer these questions, two models are presented. The first presents a straightforward linear equation for the demand for petroleum due to a change in total fuel consumption. This is then used in Model 2, which is basically the Slutsky equation, to obtain the mean substitution effect between petroleum and coal, gas and electricity. This, then, measures the net substitution or complementarity between petroleum and the commodities mentioned. 11 references.

  3. Petroleum marketing monthly

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-08-01

    The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

  4. Petroleum marketing monthly

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-07-01

    Petroleum Marketing Monthly (PPM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o. b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

  5. Petroleum marketing monthly

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

  6. Petroleum 2006. Statistical elements

    International Nuclear Information System (INIS)

    2007-06-01

    This document gathers in 5 parts, the main existing statistical data about petroleum industry in France and in the rest of the world, together with an insight on other energy sources: 1 - petroleum in the French economy (petroleum and other energies, petroleum and transports, petroleum and energy in the industry, the residential and tertiary sectors, environment: 42 pages); 2 - the French petroleum industry (exploration, production, foreign trade, transports, refining, storage, petrochemistry: 66 pages); 3 - the French market of petroleum products (evolution of sales by product and detail by region for the past year: 38 pages); 4 - prices and taxes of petroleum products (world prices and rates for crude and refined products, evolution of fret rates, retail prices and French taxes: 28 pages); 5 - petroleum in the world (world energy production and consumption, detailed petroleum activity by main areas and for the main countries: 112 pages). (J.S.)

  7. Capillary pressure and saturation relations for supercritical CO2 and brine in sand: High-pressure Pc(Sw) controller/meter measurements and capillary scaling predictions

    Science.gov (United States)

    Tokunaga, Tetsu K.; Wan, Jiamin; Jung, Jong-Won; Kim, Tae Wook; Kim, Yongman; Dong, Wenming

    2013-08-01

    In geologic carbon sequestration, reliable predictions of CO2 storage require understanding the capillary behavior of supercritical (sc) CO2. Given the limited availability of measurements of the capillary pressure (Pc) dependence on water saturation (Sw) with scCO2 as the displacing fluid, simulations of CO2 sequestration commonly rely on modifying more familiar air/H2O and oil/H2O Pc(Sw) relations, adjusted to account for differences in interfacial tensions. In order to test such capillary scaling-based predictions, we developed a high-pressure Pc(Sw) controller/meter, allowing accurate Pc and Sw measurements. Drainage and imbibition processes were measured on quartz sand with scCO2-brine at pressures of 8.5 and 12.0 MPa (45°C), and air-brine at 21°C and 0.1 MPa. Drainage and rewetting at intermediate Sw levels shifted to Pc values that were from 30% to 90% lower than predicted based on interfacial tension changes. Augmenting interfacial tension-based predictions with differences in independently measured contact angles from different sources led to more similar scaled Pc(Sw) relations but still did not converge onto universal drainage and imbibition curves. Equilibrium capillary trapping of the nonwetting phases was determined for Pc = 0 during rewetting. The capillary-trapped volumes for scCO2 were significantly greater than for air. Given that the experiments were all conducted on a system with well-defined pore geometry (homogeneous sand), and that scCO2-brine interfacial tensions are fairly well constrained, we conclude that the observed deviations from scaling predictions resulted from scCO2-induced decreased wettability. Wettability alteration by scCO2 makes predicting hydraulic behavior more challenging than for less reactive fluids.

  8. Present situation of the development of petroleum substitution energy (The UK); Sekiyu daitai energy kaihatsu no genjo (Eikoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With relation to the petroleum substitution energy in the U.K., the paper states measures taken for the development and introduction and the state of spread. Introduced were the U.K., energy policy described by energy field, petroleum and natural gas, coal, nuclear power, electric power, renewable energy (petroleum substitution energy), and the policy on energy conservation and the recent trend. Further, the paper took up the environmental policy relating to global warming which is an environmental problem in close connection with the energy industry and described the present status of exhaust gas such as acid rain gas and ozonospherial destruction gas, target for reduction of exhaust gas, and the present situation of exhaust gas at power plant. Explained were the positioning of and the measures for the petroleum substitution energy which was incorporated into a part of the energy policy in the U.K., especially the recent trend of obligation to use non-fossil fuel. First, the order of priority of the governmental policies was introduced, and then the NFFO order was described which was to give reliable fund base to the development toward the practical use of petroleum substitution energy. The paper also commented on recent topics on the state of the practical use of petroleum substitution energy. 2 figs., 7 tabs.

  9. 34. annual conference Ontario Petroleum Institute

    International Nuclear Information System (INIS)

    1995-01-01

    A total of 18 papers, dealing with a variety of issues relevant to the petroleum industry, such as marketing strategies, feasibility studies and exploration technologies, were combined in this volume of proceedings of the 34th annual conference of the Ontario Petroleum Institute. Some of the papers presented case studies of hydrocarbon reserves in North America, along with their depositional histories. Oil yields and resource potential of fractured reservoirs was the subject of some presentations. Studies of cores from drilling sites and complete stratigraphic columns of some oil fields were also presented. (Papers are paged individually). refs., tabs., figs

  10. Bioremediation of a Petroleum-Hydrocarbon Polluted Agricultural ...

    African Journals Online (AJOL)

    A combination of field cells involving a control and five treatment cells were evaluated under field conditions in the bioremediation of a petroleum- hydrocarbon polluted agricultural soil over a six-week period. Previous works have indicated that crude oil contamination of soils depletes oxygen reserves in the soils and slows ...

  11. Petroleum and natural gas economy in Arab countries, Angola, Iran and Nigeria

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    This paper describes briefly main informations on petroleum prices and market trends, trade and contracts, imports, demand, taxes. The Southern Oil Company has restored a production capacity of 1.8 Mb per day in the South of Iraq. In Iran, a joint venture between France and Iran (Iranian French Gas Co.) has been created and precedes the establishment of an european consortium for iranian gas import. In Jordan, in the natural gas field of Risha, a new discovery can give 633000 m 3 per day. Informations on petroleum exploration or production in Tunisia (Rhemoura oil field), in Syria (Dez ez Zor Petroleum Company), in Angola are also offered

  12. Remediation plan for contaminated areas by naturally occurring radioactivity materials in Syrian petroleum company oil fields

    International Nuclear Information System (INIS)

    Shwekani, R.; Al-Masri, M.S.; Awad, I.

    2005-08-01

    The present report contains a detailed plan for remediation of areas contaminated with naturally occurring radioactive materials in the Syrian petroleum company oil fields. This plan includes a description of the contaminated areas and the procedures that will be followed before and during the execution of the project in addition to the final radiation surveys according to the Syrian regulations. In addition, responsibilities of the main personnel who will carry out the work have been defined and the future monitoring program of the remediated areas was determined. (author)

  13. Remediation plan for contaminated areas by naturally occurring radioactivity materials in Syrian Petroleum Company oil fields

    International Nuclear Information System (INIS)

    Shweikani, R.; Al-Masri, M. S.; Awad, I.

    2006-01-01

    The present report contains a detailed plan for remediation of areas contaminated with naturally occurring radioactive materials in the syrian Petroleum Company Oil fields. This plan includes a description of the contaminated areas and the procedures that will be followed before and during the execution of the project in addition to the final radiation surveys according to the Syrian regulations. In addition, responsibilities of the main personnel who will carry out the work have been defined and the future monitoring program of the remediated areas was determined. (author)

  14. Insertion sequences enrichment in extreme Red sea brine pool vent

    KAUST Repository

    Elbehery, Ali H. A.

    2016-12-03

    Mobile genetic elements are major agents of genome diversification and evolution. Limited studies addressed their characteristics, including abundance, and role in extreme habitats. One of the rare natural habitats exposed to multiple-extreme conditions, including high temperature, salinity and concentration of heavy metals, are the Red Sea brine pools. We assessed the abundance and distribution of different mobile genetic elements in four Red Sea brine pools including the world’s largest known multiple-extreme deep-sea environment, the Red Sea Atlantis II Deep. We report a gradient in the abundance of mobile genetic elements, dramatically increasing in the harshest environment of the pool. Additionally, we identified a strong association between the abundance of insertion sequences and extreme conditions, being highest in the harshest and deepest layer of the Red Sea Atlantis II Deep. Our comparative analyses of mobile genetic elements in secluded, extreme and relatively non-extreme environments, suggest that insertion sequences predominantly contribute to polyextremophiles genome plasticity.

  15. Brine migration test report: Asse Salt Mine, Federal Republic of Germany: Technical report

    International Nuclear Information System (INIS)

    Coyle, A.J.; Eckert, J.; Kalia, H.

    1987-01-01

    This report presents a summary of Brine Migration Tests which were undertaken at the Asse mine of the Federal Republic of Germany (FRG) under a bilateral US/FRG agreement. This experiment simulates a nuclear waste repository at the 800-m (2624-ft) level of the Asse salt mine in the Federal Republic of Germany. This report describes the Asse salt mine, the test equipment, and the pretest properties of the salt in the mine and in the vicinity of the test area. Also included are selected test data (for the first 28 months of operation) on the following: brine migration rates, thermomechaical behavior of the salt (including room closure, stress reading, and thermal profiles), borehole gas pressures, and borehole gas analyses. In addition to field data, laboratory analyses of pretest salt properties are included in this report. The operational phase of these experiments was completed on October 4, 1985, with the commencement of cooldown and the start of posttest activities. 7 refs., 68 figs., 48 tabs

  16. Petroleum fiscality indicators

    International Nuclear Information System (INIS)

    2008-02-01

    This document presents the different taxes imposed to petroleum products in France: domestic tax on petroleum products (TIPP) and added value tax (TVA). A comparison is made with the fiscality into effect in other European countries for some petroleum products. Then, the fiscality is detailed for the different petroleum products and automotive fuels with its regional modulations. Finally, the fiscal measures adopted in 2007 are detailed. They concern the transposition of the European directive 2003-96/CE into French right and some fiscal regime changes given to some economical sectors particularly penalized by the rise of petroleum energy prices in 2007. (J.S.)

  17. Petroleum industry 1996

    International Nuclear Information System (INIS)

    1997-01-01

    A survey on petroleum industry activities in France and in the world in 1996 is presented. The different parts and themes of the study are: evolution of the petroleum market (international and French markets, supply and demand, prices, mark-up and taxation in France and in Europe); activities in the petroleum industries (exploration and production, maritime transportation, inland transportation and storage, refining, quality of petroleum products and substitution fuels, oil distribution); environment and safety (refining, distribution and evolution of products, pipeline and maritime transportation, exploration and production); situation of the sector's companies (oil groups, para-petroleum French industry, scientific and technical research)

  18. Petroleum industry in 2004

    International Nuclear Information System (INIS)

    2005-01-01

    This document presents a detailed outlook of the petroleum industry in the world and more particularly in France in 2005: evolution of crude oil prices; petroleum exploration and production in the world and in France; the French para-petroleum and petroleum industry; the oil supplies; the refining activities; the evolution of products quality and the substitution fuels; the domestic transports, the storage and consumption of petroleum products; the fiscality, prices and distribution of petroleum products. (J.S.)

  19. Microbial changes and growth of Listeria monocytogenes during chilled storage of brined shrimp ( Pandalus borealis )

    DEFF Research Database (Denmark)

    Mejlholm, Ole; Kjeldgaard, J.; Modberg, A.

    2008-01-01

    Thirteen storage trials and ten challenge tests were carried out to examine microbial changes, spoilage and the potential growth of Listeria monocytogenes in brined shrimp (Pandalus borealis). Shrimp in brine as well as brined and drained shrimp in modified atmosphere packaging (MAP) were produced...... and lactic acids were studied. Furthermore, the effect of adding diacetate to brined shrimp was evaluated. A single batch of cooked and peeled shrimp was used to study both industrially and manually processed brined shrimp with respect to the effect of process hygiene on microbial changes and the shelf life...... of products. Concentrations of microorganisms on newly produced brined shrimp from an industrial scale processing line were 1.0-2.3 log (CFU g(-1)) higher than comparable concentrations in manually processed samples. This resulted in a substantially shorter shelf life and a more diverse spoilage microflora...

  20. Problems in waterflooding fields containing paraffinic crude oils

    Energy Technology Data Exchange (ETDEWEB)

    Kovalev, A G; Lyutin, L V; Perevalov, V G

    1968-11-01

    When Caspian seawater is injected into the Uzen field reservoir, the temperature of the reservoir oil can be lowered 10/sup 0/ to 20/sup 0/C below initial reservoir temperature. Because Uzen crude oil is saturated with paraffin, the cold injection water can deposit paraffin in the formation and reduce oil recovery. In a related study, it was shown that the lower temperature should not adversely affect capillary and wettability behavior of the crude oil in the reservoir. Oil recovery was found to be essentially independent of water composition. However, fresh water is easier to handle in injection systems than brines. Several studies have shown that oil recovery from Uzen field should be increased by use of hot injection water. Various methods of heating the water are discussed. To reduce corrosivity and scaling of hot brine, sodium hexametaphosphate is added in concentrations of 2 to 15 mg/liter. It is concluded that it would be practical to use hot injection water in this field.

  1. Viruses-to-mobile genetic elements skew in the deep Atlantis II brine pool sediments

    KAUST Repository

    Adel, Mustafa

    2016-09-06

    The central rift of the Red Sea has 25 brine pools with different physical and geochemical characteristics. Atlantis II (ATIID), Discovery Deeps (DD) and Chain Deep (CD) are characterized by high salinity, temperature and metal content. Several studies reported microbial communities in these brine pools, but few studies addressed the brine pool sediments. Therefore, sediment cores were collected from ATIID, DD, CD brine pools and an adjacent brine-influenced site. Sixteen different lithologic sediment sections were subjected to shotgun DNA pyrosequencing to generate 1.47 billion base pairs (1.47 × 109 bp). We generated sediment-specific reads and attempted to annotate all reads. We report the phylogenetic and biochemical uniqueness of the deepest ATIID sulfur-rich brine pool sediments. In contrary to all other sediment sections, bacteria dominate the deepest ATIID sulfur-rich brine pool sediments. This decrease in virus-to-bacteria ratio in selected sections and depth coincided with an overrepresentation of mobile genetic elements. Skewing in the composition of viruses-to-mobile genetic elements may uniquely contribute to the distinct microbial consortium in sediments in proximity to hydrothermally active vents of the Red Sea and possibly in their surroundings, through differential horizontal gene transfer.

  2. Ex-situ bioremediation of petroleum contaminated soil

    International Nuclear Information System (INIS)

    Minier, M.R.

    1994-01-01

    The use of stress acclimated bacteria and nutrient supplements to enhance the biodegradation of petroleum contaminated soil can be a cost effective and reliable treatment technology to reduce organic contaminant levels to below established by local, state, and federal regulatory clean-up criteria. This paper will summarize the results of a field study in which 12,000 yds 3 of petroleum contaminated soil was successfully treated via ex-situ bioremediation and through management of macro and micronutrient concentrations, as well as, other site specific environmental factors that are essential for optimizing microbial growth

  3. 19 CFR 151.47 - Optional entry of net quantity of petroleum or petroleum products.

    Science.gov (United States)

    2010-04-01

    ... 19 Customs Duties 2 2010-04-01 2010-04-01 false Optional entry of net quantity of petroleum or petroleum products. 151.47 Section 151.47 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF... Petroleum and Petroleum Products § 151.47 Optional entry of net quantity of petroleum or petroleum products...

  4. Evaluation of polymer efficiency on the inhibition of calcium carbonate scale in synthetic brines; Avaliacao da acao de polimeros sobre a inibicao de incrustacoes de carbonato de calcio em salmouras sinteticas

    Energy Technology Data Exchange (ETDEWEB)

    Freitas, Juliana M.; Rodrigues, Jessica S.; Loureiro, Tatiana S.; Lucas, Elizabete F.; Spinelli, Luciana S. [Universidade Federal do Rio de Janeiro, Instituto de Macromoleculas, Laboratorio de Macromoleculas e Coloides na Industria de Petroleo, RJ (Brazil)], e-mail: julianamatos@ima.ufrj.br

    2011-07-01

    The inorganic scale results in serious problems for oil production. This scale results from the incompatibility between the chemical compositions of formation water and injection, and the changes of thermodynamic system. These deposits consist mainly of calcium carbonate and barium sulfate. In order to prevent the formation of these deposits, the petroleum industry has made use of chemicals that act as scale inhibitors. The aim of this study was to test the ability of two types of polymeric inhibitors prevent the formation of calcium carbonate from brines of different compositions with high concentrations of calcium. The inhibitors were tested at varying concentrations and at fixed conditions of temperature, pH, pressure and time. The estimated effectiveness of each inhibitor was measured by complexometric titration. The inhibitor carboxylic acid-based (poly (maleic acid)) was more efficient at relatively low concentrations, which is important both economically and environmentally. (author)

  5. Guidelines to Facilitate the Evaluation of Brines for Winter Roadway Maintenance Operations.

    Science.gov (United States)

    2017-09-19

    This document presents guidelines to facilitate the evaluation of brines for winter weather roadway maintenance applications in Texas. Brines are used in anti-icing applications which typically consist of placing liquid snow and ice control chemicals...

  6. The technology of uranium extraction from the brine with high chlorine-ion content

    International Nuclear Information System (INIS)

    Khakimov, N.; Nazarov, Kh.M.; Mirsaidov, I.U.; Negmatov, Sh.I.; Barotov, B.B.

    2010-01-01

    Present article is devoted to technology of uranium extraction from the brine with high chlorine-ion content. The research results on uranium extraction from the brine of Sasik-Kul Lake by means of sorption method were considered. The chemical composition of salt was determined. The process of uranium sorption was described and analyzed. The technology of uranium extraction from the brine with high chlorine-ion content was proposed.

  7. [Study on the groundwater petroleum contaminant remediation by air sparging].

    Science.gov (United States)

    Wang, Zhi-Qiang; Wu, Qiang; Zou, Zu-Guang; Chen, Hong; Yang, Xun-Chang; Zhao, Ji-Chu

    2007-04-01

    The groundwater petroleum contaminant remediation effect by air sparging was investigated in an oil field. The results show that the soil geological situation has great influence on the air distribution, and the shape of air distribution is not symmetrical to the air sparging (AS) well as axis. The influence distance in the left of AS well is 6 m, and only 4 m in the right. The petroleum removal rate can reach 70% in the zone with higher air saturation, but only 40% in the zone with lower air saturation, and the average petroleum removal rate reaches 60% in the influence zone for 40 days continuous air sparging. The petroleum components in groundwater were analyzed by GC/MS (gas chromatogram-mass spectrograph) before and after experiments, respectively. The results show that the petroleum removal rate has relationship with the components and their properties. The petroleum components with higher volatility are easily removed by volatilization, but those with lower volatility are difficult to remove, so a tailing effect of lingering residual contaminant exists when the air sparging technology is adopted to treat groundwater contaminated by petroleum products.

  8. Nuclear techniques in the prospecting and exploitation of petroleum

    International Nuclear Information System (INIS)

    Balcazar, M.; Lopez, A.; Castellanos, J.P.

    2003-01-01

    The apatite is a mineral that is found in the perforation nucleus of petroleum exploration whose natural content of Uranium is of around 10 ppm. This uranium is spontaneously fissioned producing fission traces whose number it is proportional to the age of the apatite and whose longitudes remained stable to temperatures smaller than 60 C, they decreased partially in the temperature range of 60 to 120 C and they faded totally if the nucleus of perforation was to temperatures bigger than 120 C. This agreement in the call 'thermal formation window' of the petroleum among 60 and 120 C and the partial erased of the longitudes of fission traces in the apatite, it allows to use this to determine not only the age of the petroleum field, but also their geologic thermal history (paleo temperature), it also allows to model the formation of the petroleum field and to contribute to outline to PEMEX on exploitation and exploration strategies. In this work it is presented: the visualization of the fission traces in the apatite of Cerro de Mercado, Durango, considered as an international standard of dating; the basic principles of this nuclear technique that allow to determine the age of the apatite; the formation of horizontal fission traces inside the apatite, by irradiation with fission fragments; and as the analysis of the thermal instability of the lengths of the fission traces it provides information of the paleo temperature of the petroleum basin. (Author)

  9. The petroleum industry in 2003

    International Nuclear Information System (INIS)

    2004-01-01

    This 2004 edition of the petroleum industry activities presents results and data concerning the crude oil prices evolution, the petroleum exploration and production in france and in the world, the para-petroleum industry, the hydrocarbons supplies, the refining, the quality evolution of the substitution products and fuels, the internal transports of petroleum products, the petroleum products storage, the petroleum products consumption, the petroleum products prices and taxation, the petroleum products distribution. (A.L.B.)

  10. Exports of petroleum products, 1987

    International Nuclear Information System (INIS)

    1988-04-01

    A summary is presented of exports of motor gasoline, middle distillate, aviation turbine fuel, heavy fuel oil, and partially processed oil from Canada for the 1987 calendar year. A discussion of petroleum product imports is included in order to put exports in the context of the overall trade. Exports of the above petroleum products averaged 22,200 m 3 /d in 1987, up 15% from 1986 levels. Exports of middle distillates and aviation fuel had the largest gains in 1987. Export prices for light petroleum products stayed relatively close to USA spot prices. The heavy fuel oil price was below the New York spot price in the beginning of 1987 but remained close for the rest of the year. Canada's petroleum products exports were made to 5 countries while imports came from at least 13 countries. The USA remained Canada's largest trading partner in petroleum products. Exports to Japan and the Far East rose ca 60% over 1986. Product outturns for export were 9% of total Canadian refinery throughput. Exports of aviation turbine fuel from Ontario began in April 1987. The top single exporter in Canada was Irving Oil Ltd. with 2,485,000 m 3 . Irving was also the top exporter in 1986. 11 figs., 4 tabs

  11. Petroleum marketing monthly

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data.

  12. INTRAVAL Phase 2 WIPP 1 test case report: Modeling of brine flow through halite at the Waste Isolation Pilot Plant site

    International Nuclear Information System (INIS)

    Beauheim, R.L.

    1997-05-01

    This report describes the WIPP 1 test case studied as part of INTRAVAL, an international project to study validation of geosphere transport models. The WIPP 1 test case involved simulation of measured brine-inflow rates to boreholes drilled into the halite strata surrounding the Waste Isolation Pilot Plant repository. The goal of the test case was to evaluate the use of Darcy's law to describe brine flow through halite. The general approach taken was to try to obtain values of permeability and specific capacitance that would be: (1) consistent with other available data and (2) able to provide reasonable simulations of all of the brine-inflow experiments performed in the Salado Formation. All of the teams concluded that the average permeability of the halite strata penetrated by the holes was between approximately 10 -22 and 10 -21 m 2 . Specific capacitances greater than 10 -10 Pa -1 are inconsistent with the known constitutive properties of halite and are attributed to deformation, possibly ongoing, of the halite around the WIPP excavations. All project teams found that Darcy-flow models could replicate the experimental data in a consistent and reasonable manner. Discrepancies between the data and simulations are attributed to inadequate representation in the models of processes modifying the pore-pressure field in addition to the experiments themselves, such as ongoing deformation of the rock around the excavations. Therefore, the conclusion from the test case is that Darcy-flow models can reliably be used to predict brine flow to WIPP excavations, provided that the flow modeling is coupled with measurement and realistic modeling of the pore-pressure field around the excavations. This realistic modeling of the pore-pressure field would probably require coupling to a geomechanical model of the stress evolution around the repository

  13. Petroleum exploration and development opportunities in Manitoba

    International Nuclear Information System (INIS)

    Fox, J.N.; Martiniuk, C.D.

    1992-01-01

    The productive areas of Manitoba are located along the northeastern flank of the Williston basin. Rocks of Paleozoic, Mesozoic and Cenozoic age form a basin-ward thickening wedge of sedimentary strata that reach a total thickness of 2,300 m in the southwest corner of the province. A brief description is presented of the geology and reservoir characteristics of petroleum producing horizons in Manitoba. Manitoba's Crown land tenure system of leases and exploitation reservations is described and an overview of Manitoba's petroleum royalty and tax structure and incentive programs is presented. Exploration and development opportunities in Manitoba are outlined. There are numerous development drilling opportunities along the poorly defined edges of existing pools. Exploration opportunities exist in the Mississippian in the sparsely explored areas outside existing field boundaries. Deeper Devonian and Ordovician horizons, productive elsewhere in the Williston basin, remain relatively untested in Manitoba. An attractive, stable investment climate is created by: availability of land at comparatively low cost; a stable and competitive fiscal regime; incentive programs designed to enhance pay-out; low drilling density; relatively untested deep potential below the Mississippian; low drilling and completion costs; easy access to market; and competitive oil prices. 12 refs., 11 figs., 7 tabs

  14. Petroleum exploration and development opportunities in Manitoba

    International Nuclear Information System (INIS)

    Fox, J.N.; Martiniuk, C.D.

    1991-01-01

    The productive areas of Manitoba are located along the northeastern flank of the Williston basin. Rocks of paleozoic, Mesozoic and Cenozoic age form a basin-ward thickening wedge of sedimentary strata that reach a total thickness of 2,300 m in the southwest corner of the province. A brief description is presented of the geology and reservoir characteristics of petroleum producing horizons in Manitoba. Manitoba's Crown land tenure system of leases and exploitation reservations is described and an overview of Manitoba's petroleum royalty and tax structure and incentive programs is presented. Exploration and development opportunities in Manitoba are outlined. There are numerous development drilling opportunities along the poorly defined edges of existing pools. Exploration opportunities exist in the Mississippian in the sparsely explored areas outside existing field boundaries. Deeper Devonian and Ordovician horizons, productive elsewhere in the Williston basin, remain relatively untested in Manitoba. An attractive, stable investment climate is created by: availability of land at comparatively low cost; a stable and competitive fiscal regime; incentive programs designed to enhance pay-out; low drilling density; relatively untested deep potential below the Mississippian; low drilling and completion costs; easy access to market; and competitive oil prices. 12 refs., 11 figs., 7 tabs

  15. Surface-downhole and crosshole geoelectrics for monitoring of brine injection at the Ketzin CO2 storage site

    Science.gov (United States)

    Rippe, Dennis; Bergmann, Peter; Labitzke, Tim; Wagner, Florian; Schmidt-Hattenberger, Cornelia

    2016-04-01

    The Ketzin pilot site in Germany is the longest operating on-shore CO2 storage site in Europe. From June 2008 till August 2013, a total of ˜67,000 tonnes of CO2 were safely stored in a saline aquifer at depths of 630 m to 650 m. The storage site has now entered the abandonment phase, and continuation of the multi-disciplinary monitoring as part of the national project "CO2 post-injection monitoring and post-closure phase at the Ketzin pilot site" (COMPLETE) provides the unique chance to participate in the conclusion of the complete life cycle of a CO2 storage site. As part of the continuous evaluation of the functionality and integrity of the CO2 storage in Ketzin, from October 12, 2015 till January 6, 2015 a total of ˜2,900 tonnes of brine were successfully injected into the CO2 reservoir, hereby simulating in time-lapse the natural backflow of brine and the associated displacement of CO2. The main objectives of this brine injection experiment include investigation of how much of the CO2 in the pore space can be displaced by brine and if this displacement of CO2 during the brine injection differs from the displacement of formation fluid during the initial CO2 injection. Geophysical monitoring of the brine injection included continuous geoelectric measurements accompanied by monitoring of pressure and temperature conditions in the injection well and two adjacent observation wells. During the previous CO2 injection, the geoelectrical monitoring concept at the Ketzin pilot site consisted of permanent crosshole measurements and non-permanent large-scale surveys (Kiessling et al., 2010). Time-lapse geoelectrical tomographies derived from the weekly crosshole data at near-wellbore scale complemented by six surface-downhole surveys at a scale of 1.5 km showed a noticeable resistivity signature within the target storage zone, which was attributed to the CO2 plume (Schmidt-Hattenberger et al., 2011) and interpreted in terms of relative CO2 and brine saturations (Bergmann

  16. Facts 2000. Norwegian petroleum activities; Fakta 2000. Norsk petroleumsvirksomhet

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The petroleum resources discovered on the Norwegian Continental Shelf amounts to about 9,6 billion Sm{sup 3} oil equivalents, 76 percent in the North Sea, 20 percent in the Norwegian Sea and 4 percent in the Barents Sea. The present publication gives a summary of the resources, the exploration, the field development, the production of oil and gas, and the revenue from petroleum sale for the year 1999.

  17. [Experimental interaction of halophilic prokaryotes and opportunistic bacteria in brine].

    Science.gov (United States)

    Selivanova, E A; Nemtseva, N V

    2013-01-01

    Study the effect of extremely halophilic archaea and moderately halophilic bacteria on preservation of opportunistic bacteria in brine. 17 strains of moderately halophilic bacteria and 2 strains of extremely halophilic archaea were isolated from continental hypersaline lake Razval of Sol-Iletsk area of Orenburg Region. Identification of pure cultures of prokaryotes was carried out taking into account their phenotype properties and based on determination of 16S RNA gene sequence. The effect of halophilic prokaryote on elimination of Escherichia coli from brine was evaluated during co-cultivation. Antagonistic activity of cell extracts of the studied microorganisms was evaluated by photometric method. A more prolonged preservation of an E. coli strain in brine in the presence of live cells of extremely halophilic archaea Halorubrum tebenquichense and moderately halophilic bacteria Marinococcus halophilus was established. Extracts of cells of extremely halophilic archaea and moderately halophilic bacteria on the contrary displayed antagonistic activity. The protective effect of live cells of halophilic prokaryotes and antagonistic activity of their cell extracts change the period of conservation of opportunistic bacteria in brine that regulates inter-microbial interactions and changes the period of self-purification that reflects the sanitary condition of a hypersaline water body.

  18. Experimental investigation of CO2-brine-rock interactions at elevated temperature and pressure: Implications for CO2 sequestration in deep-saline aquifers

    Science.gov (United States)

    Rosenbauer, R.J.; Koksalan, T.; Palandri, J.L.

    2005-01-01

    Deep-saline aquifers are potential repositories for excess CO2, currently being emitted to the atmosphere from anthropogenic activities, but the reactivity of supercritical CO2 with host aquifer fluids and formation minerals needs to be understood. Experiments reacting supercritical CO2 with natural and synthetic brines in the presence and absence of limestone and plagioclase-rich arkosic sandstone showed that the reaction of CO2-saturated brine with limestone results in compositional, mineralogical, and porosity changes in the aquifer fluid and rock that are dependent on initial brine composition, especially dissolved calcium and sulfate. Experiments reacting CO2-saturated, low-sulfate brine with limestone dissolved 10% of the original calcite and increased rock porosity by 2.6%. Experiments reacting high-sulfate brine with limestone, both in the presence and absence of supercritical CO2, were characterized by the precipitation of anhydrite, dolomitization of the limestone, and a final decrease in porosity of 4.5%. However, based on favorable initial porosity changes of about 15% due to the dissolution of calcite, the combination of CO2 co-injection with other mitigation strategies might help alleviate some of the well-bore scale and formation-plugging problems near the injection zone of a brine disposal well in Paradox Valley, Colorado, as well as provide a repository for CO2. Experiments showed that the solubility of CO2 is enhanced in brine in the presence of limestone by 9% at 25 ??C and 6% at 120 ??C and 200 bar relative to the brine itself. The solubility of CO2 is enhanced also in brine in the presence of arkosic sandstone by 5% at 120 ??C and 300 bar. The storage of CO 2 in limestone aquifers is limited to only ionic and hydraulic trapping. However, brine reacted with supercritical CO2 and arkose yielded fixation and sequestration of CO2 in carbonate mineral phases. Brine desiccation was observed in all experiments containing a discrete CO2 phase

  19. Lithium recovery from salt lake brine by H2TiO3.

    Science.gov (United States)

    Chitrakar, Ramesh; Makita, Yoji; Ooi, Kenta; Sonoda, Akinari

    2014-06-21

    The details of the ion exchange properties of layered H2TiO3, derived from the layered Li2TiO3 precursor upon treatment with HCl solution, with lithium ions in the salt lake brine (collected from Salar de Uyuni, Bolivia) are reported. The lithium adsorption rate is slow, requiring 1 d to attain equilibrium at room temperature. The adsorption of lithium ions by H2TiO3 follows the Langmuir model with an adsorptive capacity of 32.6 mg g(-1) (4.7 mmol g(-1)) at pH 6.5 from the brine containing NaHCO3 (NaHCO3 added to control the pH). The total amount of sodium, potassium, magnesium and calcium adsorbed from the brine was lithium ions from the brine containing competitive cations such as sodium, potassium, magnesium and calcium in extremely large excess. The results indicate that the selectivity order Li(+) ≫ Na(+), K(+), Mg(2+), Ca(2+) originates from a size effect. The H2TiO3 can be regenerated and reused for lithium exchange in the brine with an exchange capacity very similar to the original H2TiO3.

  20. A Field Study of NMR Logging to Quantify Petroleum Contamination in Subsurface Sediments

    Science.gov (United States)

    Fay, E. L.; Knight, R. J.; Grunewald, E. D.

    2016-12-01

    Nuclear magnetic resonance (NMR) measurements are directly sensitive to hydrogen-bearing fluids including water and petroleum products. NMR logging tools can be used to detect and quantify petroleum hydrocarbon contamination in the sediments surrounding a well or borehole. An advantage of the NMR method is that data can be collected in both cased and uncased holes. In order to estimate the volume of in-situ hydrocarbon, there must be sufficient contrast between either the relaxation times (T2) or the diffusion coefficients (D) of water and the contaminant. In a field study conducted in Pine Ridge, South Dakota, NMR logging measurements were used to investigate an area of hydrocarbon contamination from leaking underground storage tanks. A contaminant sample recovered from a monitoring well at the site was found to be consistent with a mixture of gasoline and diesel fuel. NMR measurements were collected in two PVC-cased monitoring wells; D and T2 measurements were used together to detect and quantify contaminant in the sediments above and below the water table at both of the wells. While the contrast in D between the fluids was found to be inadequate for fluid typing, the T2 contrast between the contaminant and water in silt enabled the estimation of the water and contaminant volumes. This study shows that NMR logging can be used to detect and quantify in-situ contamination, but also highlights the importance of sediment and contaminant properties that lead to a sufficiently large contrast in T2 or D.

  1. Water isotopic characterization of hypersaline formation of a petroleum field Reconcavo basin, Brazil

    International Nuclear Information System (INIS)

    Teles, Danilo Ribeiro de Sa; Azevedo, Antonio Expedito Gomes de

    2010-01-01

    Formation water is the water present in reservoir rock pores, produced together with petroleum. Usually it is hyper saline with concentrations that can be higher than 250 g/l of dissolved solids. The concentration of the dissolved elements and the isotopic composition of the water and of some of the dissolved elements can be excellent tracers to study the dynamic of underground fluid flux, the mixing of distinct sources and the origin of salinization of these waters. This work reports the isotopic composition (δ 2 H , δ 18 O) and electrical conductivity (EC) of formation waters from 10 wells of a petroleum field of the Reconcavo Basin, looking for their evolution, interaction with the minerals and rocks and reservoir interconnection. The samples have electric conductivity ranging from 84 to 137 mS/cm, with conductivity increasing with depth of production zone. It is observed an enrichment of deuterium and oxygen-18 with the depth of production zone, probably due to water-rock interactions that were probably increased by higher temperatures of the deeper levels and longer residence times. The samples from the production zone between 1450 to 1520 m, drained by 7 of the 10 wells sampled, show a small range in isotopic composition and in electric conductivity, indicating homogeneity in this level of the reservoir. In the shallow level of 450 m the values of δ 2 H , δ 18 O and EC are lower, with isotopic composition similar to the oceanic water, possibly representing the original water that entered the reservoir during the sedimentation of the basin. (author)

  2. Shale oil. I. Genesis of oil shales and its relation to petroleum and other fuels

    Energy Technology Data Exchange (ETDEWEB)

    McKee, R H; Manning, P D.V.

    1927-01-01

    Oil-shale kerogen originated from resinous vegetation residues of past eras, whereas well petroleum was formed from oil shales by pressure and mild heat. Petroleum migrated to its present reservoir from neighboring oil-shale deposits, leaving a residue of black bituminous shales. The high carbon dioxide content of gases present in petroleum wells originated from kerogen, as it gives off carbon dioxide gas before producing soluble oil or bitumen.

  3. Ring Resonator for Detection of Melting Brine Under Shallow Subsurface of Mars

    Science.gov (United States)

    Ponchak, George E.; Jordan, Jennifer L.; Scardelletti, Maximilian C.

    2016-01-01

    Laboratory experimental evidence using Raman spectroscopy has shown that liquid brine may form below the shallow subsurface of Mars. A simpler experimental method to verify the presence of liquid brine or liquid water below Mars surface is needed. In this paper, a ring resonator is used to detect the phase change between frozen water and liquid water below a sandy soil that simulates the Mars surface. Experimental data shows that the ring resonator can detect the melting of thin layers of frozen brine or water up to 15 mm below the surface.

  4. Environmental flows and life cycle assessment of associated petroleum gas utilization via combined heat and power plants and heat boilers at oil fields

    International Nuclear Information System (INIS)

    Rajović, Vuk; Kiss, Ferenc; Maravić, Nikola; Bera, Oskar

    2016-01-01

    Highlights: • Environmental impact of associated petroleum gas flaring is discussed. • A modern trend of introducing cogeneration systems to the oil fields is presented. • Three alternative utilization options evaluated with life cycle assessment method. • Producing electricity and/or heat instead of flaring would reduce impacts. - Abstract: Flaring of associated petroleum gas is a major resource waste and causes considerable emissions of greenhouse gases and air pollutants. New environmental regulations are forcing oil industry to implement innovative and sustainable technologies in order to compete in growing energy market. A modern trend of introducing energy-effective cogeneration systems to the oil fields by replacing flaring and existing heat generation technologies powered by associated petroleum gas is discussed through material flow analysis and environmental impact assessment. The environmental assessment is based on the consequential life cycle assessment method and mainly primary data compiled directly from measurements on Serbian oil-fields or company-supplied information. The obtained results confirm that the utilization of associated petroleum gas via combined heat and power plants and heat boilers can provide a significant reduction in greenhouse gas emissions and resource depletion by displacing marginal production of heat and electricity. At the base case scenario, which assumes a 100% heat realization rate, the global warming potential of the combined heat and power plant and heat boiler scenarios were estimated at −4.94 and −0.54 kg CO_2_e_q Sm"−"3, whereas the cumulative fossil energy requirements of these scenarios were −48.7 and −2.1 MJ Sm"−"3, respectively. This is a significant reduction compared to the global warming potential (2.25 kg CO_2_e_q Sm"−"3) and cumulative fossil energy requirements (35.36 MJ Sm"−"3) of flaring. Nevertheless, sensitivity analyses have shown that life cycle assessment results are sensitive

  5. Fate and groundwater impacts of produced water releases at OSPER "B" site, Osage County, Oklahoma

    Science.gov (United States)

    Kharaka, Y.K.; Kakouros, E.; Thordsen, J.J.; Ambats, G.; Abbott, M.M.

    2007-01-01

    For the last 5 a, the authors have been investigating the transport, fate, natural attenuation and ecosystem impacts of inorganic and organic compounds in releases of produced water and associated hydrocarbons at the Osage-Skiatook Petroleum Environmental Research (OSPER) "A" and "B" sites, located in NE Oklahoma. Approximately 1.0 ha of land at OSPER "B", located within the active Branstetter lease, is visibly affected by salt scarring, tree kills, soil salinization, and brine and petroleum contamination. Site "B" includes an active production tank battery and adjacent large brine pit, two injection well sites, one with an adjacent small pit, and an abandoned brine pit and tank battery site. Oil production in this lease started in 1938, and currently there are 10 wells that produce 0.2-0.5 m3/d (1-3 bbl/d) oil, and 8-16 m3/d (50-100 bbl/d) brine. Geochemical data from nearby oil wells show that the produced water source is a Na-Ca-Cl brine (???150,000 mg/L TDS), with high Mg, but low SO4 and dissolved organic concentrations. Groundwater impacts are being investigated by detailed chemical analyses of water from repeated sampling of 41 boreholes, 1-71 m deep. The most important results at OSPER "B" are: (1) significant amounts of produced water from the two active brine pits percolate into the surficial rocks and flow towards the adjacent Skiatook reservoir, but only minor amounts of liquid petroleum leave the brine pits; (2) produced-water brine and minor dissolved organics have penetrated the thick (3-7 m) shale and siltstone units resulting in the formation of three interconnected plumes of high-salinity water (5000-30,000 mg/L TDS) that extend towards the Skiatook reservoir from the two active and one abandoned brine pits; and (3) groundwater from the deep section of only one well, BR-01 located 330 m upslope and west of the site, appear not to be impacted by petroleum operations. ?? 2007.

  6. A REVIEW OF THE KEY PROVISIONS OF THE PETROLEUM ...

    African Journals Online (AJOL)

    safety measures relating to all aspects of upstream petroleum operations, publish reports and ... Nigerian Petroleum Assets Management Company Limited12 ..... the demand” will apply and the public will be protected against monopolies,.

  7. Radiological assessment of petroleum pipe scale waste streams from dry rattling operations - 16323

    International Nuclear Information System (INIS)

    Hamilton, Ian S.; Arno, Matthew G.; Fruchtnicht, Erich H.; Berry, Robert O.

    2009-01-01

    Petroleum pipe scale consists of inorganic solids, such as barium sulfate. These solids can precipitate out of brine solutions that are pumped out of oil wells as part of normal oil field operations. The precipitates can nucleate on down hole pipe walls, causing the buildup of hard scales in some tubular in a pipe string, while leaving others virtually untouched. Once the scale buildup is sufficient to restrict flow in the string significantly, the tubular are removed from service. Once removed, tubular are transported to storage yards for storage, subsequent inspection, and possible recycling. Many of the tubular are never returned to service, either because the threads were too damaged, pipe walls too thin, or the scale buildup too thick. Historically, the tubular refurbishment industry used primarily one of two processes, either a high-pressure water lance or a dry, abrasive 'rattling' process to ream pipes free of scale buildup. The dry rattling process was primarily for touching up new pipes that have rusted slightly during storage; however, pipes with varying levels of scale were reamed, leaving only a thin coating of scale on the inner diameter, and then returned to service. Chemically, radium is an analog for barium, and radium is present in parts-per-million quantities in the brines produced from downhole pumping operations. Thus, some of the scales contain radium salts. When the radium-bearing scales are reamed with a dry process there is the possibility of generating radioactive aerosols, as well as bulk waste materials. At Texas A and M University, and under the university's radioactive materials broad scope license, an outdoor laboratory was constructed and operated with dry rattling equipment restored to the 'as was' condition typical of historical pipe cleaning yards. A battery of measurements were obtained to determine the radiological and aerodynamic properties of scale-waste products liberated from the inner surfaces of a variety of tubular

  8. The application of somputer and network technology in the realm of petroleum

    International Nuclear Information System (INIS)

    Liu Wei

    2003-01-01

    In the our country petroleum industry inside, the computer and network technology have become the important tools of exploring and developing new oil fields. Using jumped-up and most advanced computer and network technology will carve out wider foreground for the development of the petroleum realm. (authors)

  9. Efficacy of chlorine dioxide against Listeria monocytogenes in brine chilling solutions.

    Science.gov (United States)

    Valderrama, W B; Mills, E W; Cutter, C N

    2009-11-01

    Chilled brine solutions are used by the food industry to rapidly cool ready-to-eat meat products after cooking and before packaging. Chlorine dioxide (ClO(2)) was investigated as an antimicrobial additive to eliminate Listeria monocytogenes. Several experiments were performed using brine solutions made of sodium chloride (NaCl) and calcium chloride (CaCl(2)) inoculated with L. monocytogenes and/or treated with 3 ppm of ClO(2). First, 10 and 20% CaCl(2) and NaCl solutions (pH 7.0) were inoculated with a five-strain cocktail of L. monocytogenes to obtain approximately 7 log CFU/ml and incubated 8 h at 0 degrees C. The results demonstrated that L. monocytogenes survived in 10% CaCl(2), 10 and 20% NaCl, and pure water. L. monocytogenes levels were reduced approximately 1.2 log CFU/ml in 20% CaCl(2). Second, inoculated ( approximately 7 log CFU/ml) brine solutions (10 and 20% NaCl and 10% CaCl(2)) treated with 3 ppm of ClO(2) resulted in a approximately 4-log reduction of the pathogen within 90 s. The same was not observed in a solution of 20% CaCl(2); further investigation demonstrated that high levels of divalent cations interfere with the disinfectant. Spent brine solutions from hot dog and ham chilling were treated with ClO(2) at concentrations of 3 or 30 ppm. At these concentrations, ClO(2) did not reduce L. monocytogenes. Removal of divalent cations and organic material in brine solutions prior to disinfection with ClO(2) should be investigated to improve the efficacy of the compound against L. monocytogenes. The information from this study may be useful to processing establishments and researchers who are investigating antimicrobials in chilling brine solutions.

  10. Geomechanical Simulation of Bayou Choctaw Strategic Petroleum Reserve - Model Calibration.

    Energy Technology Data Exchange (ETDEWEB)

    Park, Byoung [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-02-01

    A finite element numerical analysis model has been constructed that consists of a realistic mesh capturing the geometries of Bayou Choctaw (BC) Strategic Petroleum Reserve (SPR) site and multi - mechanism deformation ( M - D ) salt constitutive model using the daily data of actual wellhead pressure and oil - brine interface. The salt creep rate is not uniform in the salt dome, and the creep test data for BC salt is limited. Therefore, the model calibration is necessary to simulate the geomechanical behavior of the salt dome. The cavern volumetric closures of SPR caverns calculated from CAVEMAN are used for the field baseline measurement. The structure factor, A 2 , and transient strain limit factor, K 0 , in the M - D constitutive model are used for the calibration. The A 2 value obtained experimentally from the BC salt and K 0 value of Waste Isolation Pilot Plant (WIPP) salt are used for the baseline values. T o adjust the magnitude of A 2 and K 0 , multiplication factors A2F and K0F are defined, respectively. The A2F and K0F values of the salt dome and salt drawdown skins surrounding each SPR cavern have been determined through a number of back fitting analyses. The cavern volumetric closures calculated from this model correspond to the predictions from CAVEMAN for six SPR caverns. Therefore, this model is able to predict past and future geomechanical behaviors of the salt dome, caverns, caprock , and interbed layers. The geological concerns issued in the BC site will be explained from this model in a follow - up report .

  11. Phytoremediation of petroleum-polluted soils: application of Polygonum aviculare and its root-associated (penetrated) fungal strains for bioremediation of petroleum-polluted soils.

    Science.gov (United States)

    Mohsenzadeh, Fariba; Nasseri, Simin; Mesdaghinia, Alireza; Nabizadeh, Ramin; Zafari, Doustmorad; Khodakaramian, Gholam; Chehregani, Abdolkarim

    2010-05-01

    Petroleum-polluted soils are a common disaster in many countries. Bioremediation of oil contamination in soils is based on the stimulation of petroleum-hydrocarbon-degrading fungal and microbial communities. A field study was conducted in a petroleum-contaminated site to find petroleum-resistant plants and their root-associated fungal strains for use in bioremediation of petroleum-polluted soils. Results and observations showed that the amounts of petroleum pollution in nonvegetated soils were several times higher than in vegetated soils. Plants collected from petroleum-polluted areas were identified using morphological characters. Results indicated that seven plant species were growing on the contaminated sites: Alhaji cameleron L. (Fabaceae), Amaranthus retroflexus L. var. retroflexus (Amaranthaceae), Convolvulus arvensis L. (Convolvulaceae), Chrozophora hierosolymitana Spreg. (Euphorbiaceae), Noea mucronata L. (Boraginaceae), Poa sp. (Poaceae), and Polygonum aviculare L. (Polygonaceae). The root-associated fungi of each plant were determined and results showed the presence of 11 species that associated with and also penetrated the roots of plants growing in the polluted areas. Altenaria sp. was common to all of the plants and the others had species-specific distribution within the plants. The largest numbers of fungal species (six) were determined for P. aviculare and Poa sp. in polluted areas. However, the variation of fungal strains in the plants collected from petroleum-polluted areas was greater than for nonpolluted ones. Culture of fungi in oil-contaminated media showed that all the studied fungi were resistant to low petroleum pollution (1% v/v) and a few species, especially Fusarium species, showed resistance to higher petroleum pollution (10% v/v) and may be suitable for bioremediation in highly polluted areas. Bioremediation tests with P. aviculare, with and without fungal strains, showed that application of both the plant and its root-associated fungal

  12. Brine Dewatering Using Ultrasonic Nebulization, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Recovery of water from brine is critically important for manned space exploration. Resupply of water is prohibitively costly for extended missions. It is anticipated...

  13. Coiled Brine Recovery Assembly (CoBRA) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Coiled Brine Recovery Assembly (CoBRA) project will result in a proof-of-concept demonstration for a lightweight, compact, affordable, regenerable and disposable...

  14. Brine Dewatering Using Ultrasonic Nebulization, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Recovery of water from brine is critically important for future manned space exploration. Resupply of water is prohibitively costly for such extended missions. Water...

  15. Distillation Brine Purification for Resource Recovery Applications

    Data.gov (United States)

    National Aeronautics and Space Administration — Wastewater processing systems for space generate residual brine that contains water and salts that could be recovered to reduce life support consumables. The project...

  16. Origin of brines from the coal mine Silesia inferred from stable isotope and hydrochemical data; Pochodzenie solanek kopalni Silesia w swietle badan izotopowych i hydrochemicznych

    Energy Technology Data Exchange (ETDEWEB)

    Pluta, I. [Glowny Inst. Gornictwa, Katowice (Poland); Wayor, L. [KWK Silesia, Czechowice-Dziedzice (Poland); Zuber, A. [Institute of Nuclear Physics, Cracow (Poland)

    1996-12-31

    The deepest brines in the Carboniferous formations of the Coal Mine Silesia can be identified as the oldest infiltration in the Upper Silesian Coal Basin. Two types of brines can be related to some infiltration periods before the last marine transgression. One of them is discovered for the first time in the Carboniferous formation. The three brine types of different origin are characterized by subtle differences in chemical composition. (author). 19 refs, 2 figs, 1 tab.

  17. Approach to recover strategic metals from brines

    Energy Technology Data Exchange (ETDEWEB)

    Raber, E.; Harrar, J.; Gregg, D.

    1981-09-16

    The objective of the proposed research is to evaluate hypersaline brines from geothermal sources and salt domes as possible sources for some strategic metals. This research is suggested because several previous analyses of brine from geothermal wells in the Imperial Valley, California, and from Gulf Coast salt domes, indicate near commercial values for platinum as well as other metals (i.e., gold, silver). Extraction of the platinum should be technically feasible. A research program should include more complete systematic sampling and analysis for resource delineation, followed by bench-scale investigation of several potential extraction processes. This could be followed by engineering feasibility and design studies, for extraction of the metals either as a by-product of other operations or in a stand-alone process.

  18. Corrosion and hydrogen permeation of A216 Grade WCA steel in hydrothermal magnesium-containing brines

    International Nuclear Information System (INIS)

    Haberman, J.H.; Frydrych, D.J.; Westerman, R.E.

    1988-03-01

    Corrosion rates determined at 1 month in 150/degree/C brine increased with magnesium concentration. The structure of the corrosion product, as determined by x-ray diffraction, depended upon the magnesium concentration. In brines with less than 10,000 ppM magnesium, the primary corrosion product had a spinel structure characteristic of magnetite or magnesioferrite. In brines containing magnesium concentrations greater than 20,000 ppM, the primary corrosion product had the amakinite structure characteristic of a complex iron-magnesium hydroxide. The high corrosion rates observed in brines containing high magnesium concentrations suggest that the corrosion products having the amakinite structure is less protective than corrosion products having the spinel structure. Corrosion rates in high-magnesium (inclusion) brine determined over a 6-month test duration were essentially constant. Hydrogen permeation rates observed in exposing mild steel to high-Mg/sup 2/plus// brine at 150/degree/C could be potentially damaging to a mild steel waste package container. The rate of hydrogen permeation was proportional to the brine flow rate in the autoclave. Thiourea additions to the brine increased the hydrogen permeation rate; sulfate and bromide ion additions did not. The maximum gaseous hydrogen pressure attainable is not known (based on 3Fe /plus/ 4H 2 O /plus/ Fe(sub 3)O /plus/ 4H 2 , would be /approximately/900 atmospheres), and the dependence of permeation rate on temperature is not known. 8 refs., 13 figs., 3 tabs

  19. The petroleum industry in 2005

    International Nuclear Information System (INIS)

    2006-01-01

    This document provides information on the petroleum industry for the year 2005. It discusses the world gas and petroleum markets, the world and french petroleum exploration and production, the petroleum and byproducts industry in France, the hydrocarbons supplying, the refining in France, the evolution of the products and fuels substitution quality, the internal transports of petroleum products, the storage consumption and taxes of petroleum products, the prices and distribution of the petroleum products. (A.L.B.)

  20. Environmental hazard and risk characterisation of petroleum substances: a guided "walking tour" of petroleum hydrocarbons.

    Science.gov (United States)

    Bierkens, Johan; Geerts, Lieve

    2014-05-01

    Petroleum substances are used in large quantities, primarily as fuels. They are complex mixtures whose major constituents are hydrocarbons derived from crude oil by distillation and fractionation. Determining the complete molecular composition of petroleum and its refined products is not feasible with current analytical techniques because of the huge number of molecular components. This complex nature of petroleum products, with their varied number of constituents, all of them exhibiting different fate and effect characteristics, merits a dedicated hazard and risk assessment approach. From a regulatory perspective they pose a great challenge in a number of REACH processes, in particular in the context of dossier and substance evaluation but also for priority setting activities. In order to facilitate the performance of hazard and risk assessment for petroleum substances the European oil company association, CONCAWE, has developed the PETROTOX and PETRORISK spreadsheet models. Since the exact composition of many petroleum products is not known, an underlying assumption of the PETROTOX and PETRORISK tools is that the behaviour and fate of a total petroleum substance can be simulated based on the physical-chemical properties of representative structures mapped to hydrocarbon blocks (HBs) and on the relative share of each HB in the total mass of the product. To assess how differing chemical compositions affect the simulated chemical fate and toxicity of hydrocarbon mixtures, a series of model simulations were run using an artificial petroleum substance, containing 386 (PETROTOX) or 160 (PETRORISK) HBs belonging to different chemical classes and molecular weight ranges, but with equal mass assigned to each of them. To this artificial petroleum substance a guided series of subsequent modifications in mass allocation to a delineated number of HBs belonging to different chemical classes and carbon ranges was performed, in what we perceived as a guided "walking tour

  1. Canadian petroleum history bibliography. Release update

    Energy Technology Data Exchange (ETDEWEB)

    Cass, D.

    2010-01-07

    The petroleum history bibliography was created over several years as a record dedicated to preserving the history of the Canadian petroleum industry. It comprises a list of more than 5000 publications, including books, theses, films, audio tapes, published articles and stories of the many companies that have come and gone. It aims to include all publications and audio visual products from the Social Sciences and Humanities on company histories, biographies, autobiographies, fiction, poetry and humour. An author index is included. Most government documents are excluded as they are accessible through Library and Archives Canada. This bibliography is an ongoing piece of work, and welcomes any additions relating to the study and preservation of Canadian petroleum industry history.

  2. Exports of petroleum products, 1989

    International Nuclear Information System (INIS)

    1990-04-01

    A summary is presented of exports of motor gasoline, middle distillate, aviation turbine fuel, heavy fuel oil, and partially processed oil from Canada for the 1989 calendar year. A discussion of petroleum product imports is included in order to put exports in the context of the overall trade. Exports of the above petroleum products averaged 30,400 m 3 /d in 1989, down 5% from 1988 levels. Motor gasoline shipments showed the largest decrease, down 1,500 m 3 to 7,700 m 3 /d. Export prices for light petroleum products stayed relatively close to USA spot prices except in June and July 1989, when attractive prices were obtained for shipments from the prairie provinces. The heavy fuel oil export price was similar to the USA east coast spot price in 1989, except in December. Canada's petroleum products imports in 1989 were 21,600 m 3 /d, compared to 18,400 m 3 /d in 1988. Imports of heavy fuel oil in eastern Canada rose 36% in 1989 because of industries switching from electricity and the high demand for thermal power generation. The USA remained Canada's largest trading partner in petroleum products. The top single exporter in 1989, as in 1988, was Newfoundland Processing, with a volume of 3,484,500 m 3 . 24 figs., 4 tabs

  3. Exports of petroleum products, 1988

    International Nuclear Information System (INIS)

    1989-04-01

    A summary is presented of exports of motor gasoline, middle distillate, aviation turbine fuel, heavy fuel oil, and partially processed oil from Canada for the 1988 calendar year. A discussion of petroleum product imports is included in order to put exports in the context of the overall trade. Exports of the above petroleum products averaged 32,000 m 3 /d in 1988, up 44% from 1987 levels. Each product except aviation fuel registered increases in export volumes, which reached the highest total volume of the decade. The main reason for the large increase was the first full year of production from the export-directed refinery at Come By Chance, Newfoundland. Export prices for light petroleum products stayed relatively close to USA spot prices. The heavy fuel oil price was mostly above the USA east coast spot price during 1988. Attractive prices on the USA east coast resulted in a few cargoes of middle distillate and motor gasoline shipped from British Columbia. Petroleum products imports came from 12 countries; Quebec had the largest volume of imports in 1988. The USA remained Canada's largest trading partner in petroleum products. Western exporters view the Far East as an ongoing important market. The top single exporter in Canada was Newfoundland Processing, with 32% of the total export volume. 12 figs., 3 tabs

  4. Workbook for prioritizing petroleum industry exploration and production sites for remediation

    International Nuclear Information System (INIS)

    White, G.J.

    1998-01-01

    The purpose of this Workbook is to provide a screening-level method for prioritizing petroleum exploration and production sites for remediation that is based on readily available information, but which does not require a full characterization of the sites being evaluated. The process draws heavily from the Canadian National Classification System for Contaminated Sites, and fits into the framework for ecological risk assessment provided in guidance from the US Environmental Protection Agency. Using this approach, scoring guidelines are provided for a number of Evaluation Factors relating to: (1) the contaminants present at the site; (2) the potential exposure pathways for these contaminants; and (3) the potential receptors of those contaminants. The process therefore incorporates a risk-based corrective action (RBCA) framework to estimate the relative threat posed by a site to human health and to ecological systems. Physical (non-toxic) disturbance factors have also been incorporated into the process. It should also be noted that the process described in this Workbook has not yet been field tested at petroleum E and P sites. The first logical step in the field testing of this process is to apply the method at a small number of sites to assess the availability of the information that is needed to score each evaluation factor. Following this evaluation, the Workbook process should be applied at a series of sites to determine the effectiveness of the process at ranking sites according to their relative need for remediation. Upon completion of these tests, the Workbook should be revised to reflect the findings of the field tests

  5. Figures on petroleum 1981

    Energy Technology Data Exchange (ETDEWEB)

    1981-01-01

    This table taken out from the 1981 annual report 1981 contains an introductory remark on the reorganization of mineral oil statistics up to January 82. It is followed by the tables ranged as follows: refinery capacity and production, crude oil supply, GDR-coverings, import of petroleum products, petroleum consumption, export of petroleum products, transport, oil storage tanks, motor vehicle stock, taxes and tariffs, petroleum export trade, energy consumption and world petroleum numbers. In parts the tables contain comparative figures back to 1950.

  6. Amorphous salts formed from rapid dehydration of multicomponent chloride and ferric sulfate brines: Implications for Mars

    Science.gov (United States)

    Sklute, Elizabeth C.; Rogers, A. Deanne; Gregerson, Jason C.; Jensen, Heidi B.; Reeder, Richard J.; Dyar, M. Darby

    2018-03-01

    Salts with high hydration states have the potential to maintain high levels of relative humidity (RH) in the near subsurface of Mars, even at moderate temperatures. These conditions could promote deliquescence of lower hydrates of ferric sulfate, chlorides, and other salts. Previous work on deliquesced ferric sulfates has shown that when these materials undergo rapid dehydration, such as that which would occur upon exposure to present day Martian surface conditions, an amorphous phase forms. However, the fate of deliquesced halides or mixed ferric sulfate-bearing brines are presently unknown. Here we present results of rapid dehydration experiments on Ca-, Na-, Mg- and Fe-chloride brines and multicomponent (Fe2(SO4)3 ± Ca, Na, Mg, Fe, Cl, HCO3) brines at ∼21 °C, and characterize the dehydration products using visible/near-infrared (VNIR) reflectance spectroscopy, mid-infrared attenuated total reflectance spectroscopy, and X-ray diffraction (XRD) analysis. We find that rapid dehydration of many multicomponent brines can form amorphous solids or solids with an amorphous component, and that the presence of other elements affects the persistence of the amorphous phase under RH fluctuations. Of the pure chloride brines, only Fe-chloride formed an amorphous solid. XRD patterns of the multicomponent amorphous salts show changes in position, shape, and magnitude of the characteristic diffuse scattering observed in all amorphous materials that could be used to help constrain the composition of the amorphous salt. Amorphous salts deliquesce at lower RH values compared to their crystalline counterparts, opening up the possibility of their role in potential deliquescence-related geologic phenomena such as recurring slope lineae (RSLs) or soil induration. This work suggests that a wide range of aqueous mixed salt solutions can lead to the formation of amorphous salts and are possible for Mars; detailed studies of the formation mechanisms, stability and transformation

  7. Amorphous salts formed from rapid dehydration of multicomponent chloride and ferric sulfate brines: Implications for Mars

    Science.gov (United States)

    Sklute, Elizabeth C.; Rogers, A. Deanne; Gregerson, Jason C.; Jensen, Heidi B.; Reeder, Richard J.; Dyar, M. Darby

    2018-01-01

    Salts with high hydration states have the potential to maintain high levels of relative humidity (RH) in the near subsurface of Mars, even at moderate temperatures. These conditions could promote deliquescence of lower hydrates of ferric sulfate, chlorides, and other salts. Previous work on deliquesced ferric sulfates has shown that when these materials undergo rapid dehydration, such as that which would occur upon exposure to present day Martian surface conditions, an amorphous phase forms. However, the fate of deliquesced halides or mixed ferric sulfate-bearing brines are presently unknown. Here we present results of rapid dehydration experiments on Ca–, Na–, Mg– and Fe–chloride brines and multi-component (Fe2 (SO4)3 ± Ca, Na, Mg, Fe, Cl, HCO3) brines at ∼21°C, and characterize the dehydration products using visible/near-infrared (VNIR) reflectance spectroscopy, mid-infrared attenuated total reflectance spectroscopy, and X-ray diffraction (XRD) analysis. We find that rapid dehydration of many multicomponent brines can form amorphous solids or solids with an amorphous component, and that the presence of other elements affects the persistence of the amorphous phase under RH fluctuations. Of the pure chloride brines, only Fe–chloride formed an amorphous solid. XRD patterns of the multicomponent amorphous salts show changes in position, shape, and magnitude of the characteristic diffuse scattering observed in all amorphous materials that could be used to help constrain the composition of the amorphous salt. Amorphous salts deliquesce at lower RH values compared to their crystalline counterparts, opening up the possibility of their role in potential deliquescence-related geologic phenomena such as recurring slope lineae (RSLs) or soil induration. This work suggests that a wide range of aqueous mixed salt solutions can lead to the formation of amorphous salts and are possible for Mars; detailed studies of the formation mechanisms, stability and

  8. Amorphous salts formed from rapid dehydration of multicomponent chloride and ferric sulfate brines: Implications for Mars.

    Science.gov (United States)

    Sklute, Elizabeth C; Rogers, A Deanne; Gregerson, Jason C; Jensen, Heidi B; Reeder, Richard J; Dyar, M Darby

    2018-03-01

    Salts with high hydration states have the potential to maintain high levels of relative humidity (RH) in the near subsurface of Mars, even at moderate temperatures. These conditions could promote deliquescence of lower hydrates of ferric sulfate, chlorides, and other salts. Previous work on deliquesced ferric sulfates has shown that when these materials undergo rapid dehydration, such as that which would occur upon exposure to present day Martian surface conditions, an amorphous phase forms. However, the fate of deliquesced halides or mixed ferric sulfate-bearing brines are presently unknown. Here we present results of rapid dehydration experiments on Ca-, Na-, Mg- and Fe-chloride brines and multi-component (Fe 2 (SO 4 ) 3 ± Ca, Na, Mg, Fe, Cl, HCO 3 ) brines at ∼21°C, and characterize the dehydration products using visible/near-infrared (VNIR) reflectance spectroscopy, mid-infrared attenuated total reflectance spectroscopy, and X-ray diffraction (XRD) analysis. We find that rapid dehydration of many multicomponent brines can form amorphous solids or solids with an amorphous component, and that the presence of other elements affects the persistence of the amorphous phase under RH fluctuations. Of the pure chloride brines, only Fe-chloride formed an amorphous solid. XRD patterns of the multicomponent amorphous salts show changes in position, shape, and magnitude of the characteristic diffuse scattering observed in all amorphous materials that could be used to help constrain the composition of the amorphous salt. Amorphous salts deliquesce at lower RH values compared to their crystalline counterparts, opening up the possibility of their role in potential deliquescence-related geologic phenomena such as recurring slope lineae (RSLs) or soil induration. This work suggests that a wide range of aqueous mixed salt solutions can lead to the formation of amorphous salts and are possible for Mars; detailed studies of the formation mechanisms, stability and transformation

  9. Evaluation of Oil Removal Efficiency and Enzymatic Activity in Some fungal Strains for Bioremediation of Petroleum-Polluted Soils

    Directory of Open Access Journals (Sweden)

    Fariba Mohsenzadeh

    2012-12-01

    Full Text Available Background: Petroleum pollution is a global disaster and there are several soil cleaning methods including bioremediation.Methods: In a field study, fugal strains were isolated from oil-contaminated sites of Arak refinery (Iran and their growth ability was checked in potato dextrose agar (PDA media containing 0-10% v/v crude oil, the activity of three enzymes (Catalase, Peroxidase and Phenol Oxidase was evaluated in the fungal colonies and bioremediation ability of the fungi was checked in the experimental pots containing 3 kg sterilized soil and different concentrations of petroleum (0-10% w/w.Results: Four fungal strains, Acromonium sp., Alternaria sp., Aspergillus terreus and Penicillium sp., were selected asthe most resistant ones. They were able to growth in the subjected concentrations and Alternaria sp. showed thehighest growth ability in the petroleum containing media. The enzyme assay showed that the enzymatic activity was increased in the oil-contaminated media. Bioremediation results showed that the studied fungi were able to decrease petroleum pollution. The highest petroleum removing efficiency of Aspergillus terreus, Penicillium sp.,Alternaria sp. and Acromonium sp. was evaluated in the 10%, 8%, 8% and 2% petroleum pollution respectively.Conclusions: Fungi are important microorganisms in decreasing of petroleum pollution. They have bioremediation potency that is related to their enzymatic activities.

  10. Petroleum supply monthly, April 1990

    Energy Technology Data Exchange (ETDEWEB)

    None

    1990-06-26

    The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in the Petroleum Supply Monthly describe (PSM) the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply.'' Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: (1) the Summary Statistics and (2) the Detailed Statistics.

  11. Petroleum supply monthly, April 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-04-01

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographical regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the US. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the US.

  12. [National Institute for Petroleum and Energy Research] monthly progress report, July 1992

    Energy Technology Data Exchange (ETDEWEB)

    1992-09-01

    Accomplishments for the month of July are described briefly under tasks for: Energy Production Research; Fuels Research; and Supplemental Government Program. Energy Production Research includes: reservoir assessment and characterization; TORIS research support; development of improved microbial flooding methods; surfactant flooding methods; development of improved alkaline flooding methods; mobility control and sweep improvement in chemical flooding; gas flood performance prediction improvement; mobility control, profile modification, and sweep improvement in gas flooding; three-phase relative permeability research; thermal processes for light oil recovery; thermal processes for heavy oil recovery; and imaging techniques applied to the study of fluids in porous media. Fuel Research includes: development of analytical methodology for analysis of heavy crudes; and thermochemistry and thermophysical properties of organic nitrogen- and diheteroatom-containing compounds. Supplement Government Program includes: microbial-enhanced waterflooding field project; feasibility study of heavy oil recovery in the midcontinent region--Oklahoma, Kansas, and Missouri; surfactant-enhanced alkaline flooding field project; development of methods for mapping distribution of clays in petroleum reservoirs; summary of geological and production characteristics of class 1. unstructured, deltaic reservoirs; third international reservoir characterization technical conference; process-engineering property measurements on heavy petroleum components; development and application of petroleum production technologies; upgrade BPO crude oil data base; simulation analysis of steam-foam projects; analysis of the US oil resource base and estimate of future recoverable oil; DOE education initiative project; and technology transfer to independent producers.

  13. (National Institute for Petroleum and Energy Research) monthly progress report, July 1992

    Energy Technology Data Exchange (ETDEWEB)

    1992-09-01

    Accomplishments for the month of July are described briefly under tasks for: Energy Production Research; Fuels Research; and Supplemental Government Program. Energy Production Research includes: reservoir assessment and characterization; TORIS research support; development of improved microbial flooding methods; surfactant flooding methods; development of improved alkaline flooding methods; mobility control and sweep improvement in chemical flooding; gas flood performance prediction improvement; mobility control, profile modification, and sweep improvement in gas flooding; three-phase relative permeability research; thermal processes for light oil recovery; thermal processes for heavy oil recovery; and imaging techniques applied to the study of fluids in porous media. Fuel Research includes: development of analytical methodology for analysis of heavy crudes; and thermochemistry and thermophysical properties of organic nitrogen- and diheteroatom-containing compounds. Supplement Government Program includes: microbial-enhanced waterflooding field project; feasibility study of heavy oil recovery in the midcontinent region--Oklahoma, Kansas, and Missouri; surfactant-enhanced alkaline flooding field project; development of methods for mapping distribution of clays in petroleum reservoirs; summary of geological and production characteristics of class 1. unstructured, deltaic reservoirs; third international reservoir characterization technical conference; process-engineering property measurements on heavy petroleum components; development and application of petroleum production technologies; upgrade BPO crude oil data base; simulation analysis of steam-foam projects; analysis of the US oil resource base and estimate of future recoverable oil; DOE education initiative project; and technology transfer to independent producers.

  14. Laboratory tests to determine the effect of Olkiluoto bounding brine water on buffer performance

    International Nuclear Information System (INIS)

    Martikainen, J.; Schatz, T.

    2011-10-01

    This report presents a set of results from laboratory studies on the effect of bounding brine water exposure on buffer performance. In order to evaluate the effect of bounding brine water exposure on compacted bentonite buffer performance a series of experiments were conducted using swelling pressure and hydraulic conductivity measurements as follows: Direct exposure measurements were performed on MX-80 bentonite samples encompassing a range of dry density values from 1334 to 1585 kg/m 3 . These samples were saturated directly with a 70 g/L solution composed of calcium and sodium chloride at a Ca 2+ /Na + mass ratio of 3:2. Direct exposure measurements were performed on IBECO RWC samples encompassing a range of dry density values from 1314 to 1564 kg/m 3 . These samples were saturated directly with a 68.45 g/L solution composed of calcium and sodium chloride at a Ca 2+ /Na + mass ratio of 3.2:2. A set of MX-80 and IBECO RWC samples encompassing a range of dry density values from 1018 to 1607 kg/m 3 were initially saturated with tap water followed by (indirect) exposure to a 68.45 g/L solution composed of calcium and sodium chloride at a Ca 2+ /Na + mass ratio of 3.2:2. Sample swelling pressures were continuously monitored and hydraulic conductivity measurements were performed at each constant swelling pressure condition. In some cases, exchangeable cation analyses were performed. The specific test results are summarized as follows: All of the measured swelling pressure values upon exposure to bounding brine water were lower than the corresponding values after saturation with tap water. The relative swelling pressure decrease for the IBECO RWC samples was approximately half of the corresponding decrease for the MX-80 samples. On exposure to bounding brine water, hydraulic conductivity values were increased at the lowest densities, for both the MX-80 and IBECO samples, while at higher densities hydraulic conductivity values were essentially equivalent, for both the

  15. Genomic and Transcriptomic Evidence for Carbohydrate Consumption Among Microorganisms in a Cold Seep Brine Pool

    Directory of Open Access Journals (Sweden)

    Weipeng Zhang

    2016-11-01

    Full Text Available The detailed lifestyle of microorganisms in deep-sea brine environments remains largely unexplored. Using a carefully calibrated genome binning approach, we reconstructed partial to nearly-complete genomes of 51 microorganisms in biofilms from the Thuwal cold seep brine pool of the Red Sea. The recovered metagenome-assembled genomes (MAGs belong to six different phyla: Actinobacteria, Proteobacteria, Candidatus Cloacimonetes, Candidatus Marinimicrobia, Bathyarchaeota and Thaumarchaeota. By comparison with close relatives of these microorganisms, we identified a number of unique genes associated with organic carbon metabolism and energy generation. These genes included various glycoside hydrolases, nitrate and sulfate reductases, putative bacterial microcompartment biosynthetic clusters (BMC, and F420H2 dehydrogenases. Phylogenetic analysis suggested that the acquisition of these genes probably occurred through horizontal gene transfer (HGT. Metatranscriptomics illustrated that glycoside hydrolases are among the most highly expressed genes. Our results suggest that the microbial inhabitants are well adapted to this brine environment, and anaerobic carbohydrate consumption mediated by glycoside hydrolases and electron transport systems (ETSs is a dominant process performed by microorganisms from various phyla within this ecosystem.

  16. Genomic and Transcriptomic Evidence for Carbohydrate Consumption among Microorganisms in a Cold Seep Brine Pool

    KAUST Repository

    Zhang, Weipeng

    2016-11-15

    The detailed lifestyle of microorganisms in deep-sea brine environments remains largely unexplored. Using a carefully calibrated genome binning approach, we reconstructed partial to nearly-complete genomes of 51 microorganisms in biofilms from the Thuwal cold seep brine pool of the Red Sea. The recovered metagenome-assembled genomes (MAGs) belong to six different phyla: Actinobacteria, Proteobacteria, Candidatus Cloacimonetes, Candidatus Marinimicrobia, Bathyarchaeota, and Thaumarchaeota. By comparison with close relatives of these microorganisms, we identified a number of unique genes associated with organic carbon metabolism and energy generation. These genes included various glycoside hydrolases, nitrate and sulfate reductases, putative bacterial microcompartment biosynthetic clusters (BMC), and F420H2 dehydrogenases. Phylogenetic analysis suggested that the acquisition of these genes probably occurred through horizontal gene transfer (HGT). Metatranscriptomics illustrated that glycoside hydrolases are among the most highly expressed genes. Our results suggest that the microbial inhabitants are well adapted to this brine environment, and anaerobic carbohydrate consumption mediated by glycoside hydrolases and electron transport systems (ETSs) is a dominant process performed by microorganisms from various phyla within this ecosystem.

  17. Geochemical Investigation of Vertical Migration of Petroleum ...

    African Journals Online (AJOL)

    Dr. K.J. Umar

    chimneys over faults in an overpressured zone in the western part of ... Haltenbanken area is part of a passive continental margin between the Møre Basin and the Trøndelag. Platform ... The petroleum accumulations in the Heidrun field and in.

  18. Petroleum marketing annual 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-08-24

    The Petroleum Marketing Annual (PMA) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysis, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the fob and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Annual. For this production, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication date.

  19. Petroleum marketing annual 1994

    International Nuclear Information System (INIS)

    1995-01-01

    The Petroleum Marketing Annual (PMA) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysis, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the fob and landed cost of imported crude oil, and the refiners' acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Annual. For this production, all estimates have been recalculated since their earlier publication in the Petroleum Marketing Monthly (PMM). These calculations made use of additional data and corrections that were received after the PMM publication date

  20. Syria: a waited petroleum production of 600 000 barrels per day for the end of 1993

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    This paper describes the reserves of petroleum deposits and gives statistical data on the production of the main oil fields in Syria. Petroleum production has grown from 160000 barrels per day in 1984 to 515000 barrels per day in 1992 and a production at a level of 600000 barrels per day is waited in 1993. Several petroleum companies, operating in Syria, have contributed to this rise, especially Al-Furat Petroleum Company (AFPC), joint venture between Syrian Petroleum Company (SPC) and Pecten/Shell/Deminex, followed by Deiz Ezzor Petroleum Company (DEZPC), association between the french company Elf Aquitaine and SPC. 2 tabs

  1. Comparative analysis of on site bioremediation: Alternatives for petroleum contaminated soils

    International Nuclear Information System (INIS)

    Bell, P.E.; Tremaine, S.C.

    1994-01-01

    Environmental Protection Systems, Inc. has developed a low maintenance, highly effective method to remediate petroleum and hazardous waste contamination of soils. This method combines the use of a slow release chemical oxygen source, along with nutrient amendments for the degradation of contaminants that require oxygen as a terminal electron acceptor. This method has been used successfully in bench and field experiments on creosote. The authors have performed laboratory experiments on diesel fuel. This paper describes rapid (site closure in 2.5 months in cold weather) field degradation of relatively freshly spilled diesel fuel using native bacteria and tailored nutrient amendments

  2. Alberta`s petroleum industry and the Conservation Board

    Energy Technology Data Exchange (ETDEWEB)

    Breen, D.H.

    1993-12-31

    The history of Alberta`s petroleum industry and Energy Resources Conservation Board (ERCB) was told. The conservation movement in Alberta was tracked from 1908 to the founding of the Petroleum and Natural Gas Conservation Board in 1938. Failure of Alberta`s first proration, and the Turner Valley `waste` gas conservation movement occurred during this period. The Leduc discovery and effects of the new regulatory environment on its development were discussed. The natural gas export debate, and the expansion of Alberta`s crude oil market were recounted in detail. The organization and regulation of field development which occurred during the period from 1948 to 1959 was presented. Past actions of the Petroleum and Natural Gas Conservation Board reviewed from today`s perspective. The petroleum industry and the ERCB were said to have been jointly responsible for the creation of a prosperous and confident new Alberta, moving it further and further away from the Canadian economic and political mainstream,, and reinforcing the sense of alienation that began to develop during the preceding agrarian decades. 53 figs., 48 tabs.

  3. Petroleum and natural gas economy in Arab Countries, Iran, Nigeria, Ethiopia and Ivory Coast

    International Nuclear Information System (INIS)

    1993-01-01

    This paper describes briefly main informations on petroleum production, prices and market trends, trade and contracts, petroleum exploration in Bahrain, Ethiopia, Libya, Tunisia, United Arab Emirates and Yemen. In Ivory Coast, a consortium led by Electricite de France and Bouygues has obtained the exploitation of Foxtrot natural gas field. Statistics on petroleum and natural gas reserves, production in the world in 1991 and 1992 are also given

  4. Cryogenic formation of brine and sedimentary mirabilite in submergent coastal lake basins, Canadian Arctic

    Science.gov (United States)

    Grasby, Stephen E.; Rod Smith, I.; Bell, Trevor; Forbes, Donald L.

    2013-06-01

    Two informally named basins (Mirabilite Basins 1 and 2) along a submergent coastline on Banks Island, Canadian Arctic Archipelago, host up to 1 m-thick accumulations of mirabilite (Na2SO4·10H2O) underlying stratified water bodies with basal anoxic brines. Unlike isostatically uplifting coastlines that trap seawater in coastal basins, these basins formed from freshwater lakes that were transgressed by seawater. The depth of the sill that separates the basins from the sea is shallow (1.15 m), such that seasonal sea ice formation down to 1.6 m isolates the basins from open water exchange through the winter. Freezing of seawater excludes salts, generating dense brines that sink to the basin bottom. Progressive freezing increases salinity of residual brines to the point of mirabilite saturation, and as a result sedimentary deposits of mirabilite accumulate on the basin floors. Brine formation also leads to density stratification and bottom water anoxia. We propose a model whereby summer melt of the ice cover forms a temporary freshwater lens, and rather than mixing with the underlying brines, it is exchanged with seawater once the ice plug that separates the basins from the open sea melts. This permits progressive brine development and density stratification within the basins.

  5. Water Recovery from Brines to Further Close the Water Recovery Loop in Human Spaceflight

    Science.gov (United States)

    Jackson, W. Andrew; Barta, Daniel J.; Anderson, Molly S.; Lange, Kevin E.; Hanford, Anthony J.; Shull, Sarah A.; Carter, D. Layne

    2014-01-01

    Further closure of water recovery systems will be necessary for future long duration human exploration missions. NASA's Space Technology Roadmap for Human Health, Life Support and Habitation Systems specified a milestone to advance water management technologies during the 2015 to 2019 timeframe to achieve 98% H2O recovery from a mixed wastewater stream containing condensate, urine, hygiene, laundry, and water derived from waste. This goal can only be achieved by either reducing the amount of brines produced by a water recovery system or by recovering water from wastewater brines. NASA convened a Technical Interchange Meeting (TIM) on the topic of Water Recovery from Brines (WRB) that was held on January14-15th, 2014 at Johnson Space Center. Objectives of the TIM were to review systems and architectures that are sources of brines and the composition of brines they produce, review the state of the art in NASA technology development and perspectives from other industries, capture the challenges and difficulties in developing brine processing hardware, identify key figures of merit and requirements to focus technology development and evaluate candidate technologies, and identify other critical issues including microgravity sensitivity, and concepts of operation, safety. This paper represents an initial summary of findings from the workshop.

  6. Tiger Team Assessment of the Naval Petroleum Reserves in California

    International Nuclear Information System (INIS)

    1991-12-01

    This report documents the Tiger Team Assessment of the Naval Petroleum Reserves in California (NPRC) which consists of Naval Petroleum Reserve Number 1 (NPR-1), referred to as the Elk Hills oil field and Naval Petroleum Reserve Number 2 (NPR-2), referred to as the Buena Vista oil field, each located near Bakersfield, California. The Tiger Team Assessment was conducted from November 12 to December 13, 1991, under the auspices of DOE's Office of Special Projects (OSP) under the Assistant Secretary for Environment, Safety and Health (EH). The assessment was comprehensive, encompassing environmental, safety, and health (ES ampersand H), and quality assurance (OA) disciplines; site remediation; facilities management; and waste management operations. Compliance with applicable Federal, State of California, and local regulations; applicable DOE Orders; best management practices; and internal NPRC requirements was assessed. In addition, an evaluation of the adequacy and effectiveness of DOE/NPRC, CUSA, and BPOI management of the ES ampersand H/QA programs was conducted

  7. Nuclear waste repository simulation experiments (brine migration), Asse Mine of the Federal Republic of Germany: Quarterly brine migration data report, October--December 1985

    International Nuclear Information System (INIS)

    Eckert, J.L.; Kalia, H.N.; Coyle, A.J.

    1988-03-01

    The tenth brine migration data report describes experiments simulating a nuclear waste repository at the 800-m (2624-ft) level of the Asse Salt Mine in the Federal Republic of Germany from May 1983 through December 1985. This report describes the test equipment, the Asse Salt Mine, and the pretest properties of the salt in the test gallery. This report includes test data for 31 months of operations on brine migration rates, borehole pressure, salt temperatures and thermomechanical behavior of the salt. 3 refs., 118 figs., 93 tabs

  8. Taxation and regulation of petroleum companies under asymmetric information; a monograph

    Energy Technology Data Exchange (ETDEWEB)

    Osmundsen, P

    1994-12-01

    The report relates to the taxation and regulation of petroleum companies. The main topics of this report are as follow: Taxation and regulation of petroleum companies under asymmetric information. A discussion of incentive problems and the principles for applying principal-agent analysis; taxation and regulation of petroleum companies under asymmetric information. A static adverse selection model; Petroleum Taxation with adverse selection. Interactions of dynamics in costs and information; Adverse selection and moral hazard in the petroleum industry, repeated auctions of incentive contracts; Petroleum taxation and regulation. Policy implications from principal-agent theory, and a comparison with the current Norwegian system. 54 refs., 7 figs.

  9. Taxation and regulation of petroleum companies under asymmetric information; a monograph

    International Nuclear Information System (INIS)

    Osmundsen, P.

    1994-12-01

    The report relates to the taxation and regulation of petroleum companies. The main topics of this report are as follow: Taxation and regulation of petroleum companies under asymmetric information. A discussion of incentive problems and the principles for applying principal-agent analysis; taxation and regulation of petroleum companies under asymmetric information. A static adverse selection model; Petroleum Taxation with adverse selection. Interactions of dynamics in costs and information; Adverse selection and moral hazard in the petroleum industry, repeated auctions of incentive contracts; Petroleum taxation and regulation. Policy implications from principal-agent theory, and a comparison with the current Norwegian system. 54 refs., 7 figs

  10. Petroleum supply monthly, January 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-15

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  11. Petroleum supply monthly, October 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-10-26

    The Petroleum Supply Monthly (PSM) is one of a family of four publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other publications are the Weekly Petroleum Status Report (WPSR), the Winter Fuels Report, and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  12. Petroleum Supply Monthly, August 1990

    Energy Technology Data Exchange (ETDEWEB)

    1990-10-30

    The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) district movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics.

  13. Petroleum supply monthly, September 1991

    Energy Technology Data Exchange (ETDEWEB)

    1991-09-30

    The Petroleum Supply Monthly (PSM) is one of a family of three publications produced by the Petroleum Supply Division within the Energy Information Administration (EIA) reflecting different levels of data timeliness and completeness. The other two publications are the Weekly Petroleum Status Report (WPSR) and the Petroleum Supply Annual (PSA). Data presented in PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administrations for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections (1) the Summary Statistics and (2) the Detailed Statistics. 65 tabs.

  14. Natural gas in 1927: Petroleum in 1927: The oil and gas fields of Ontario. Annual publication

    Energy Technology Data Exchange (ETDEWEB)

    Harkness, R B

    1930-12-31

    This annual report presents figures for gas consumption in Ontario, gas wells and their production, and leakage. It includes licenses issued for the year and logs of wells. Information is also given on oil production in Ontario, petroleum refining and petroleum imported into Ontario.

  15. Attraction aspects of petroleum industry: fragilities and opportunities for the petroleum companies - part 1; Atratividade da industria para-petrolifera: fragilidades e oportunidades para as petroleiras - parte 1

    Energy Technology Data Exchange (ETDEWEB)

    Duque, Marcelo Ascher; Szklo, Alexandre [Universidade Federal do Rio de Janeiro (PPE/COPPE/UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-Graduacao de Engenharia. Programa de Planejamento Energetico

    2010-07-01

    This paper is the first part of the study that examine the structure of the para-petroleum worldwide industry, in accordance with strategies of the largest service industries, the merger and the acquisitions, and the positioning of petroleum operators related to their suppliers. Through the characterization of service sector activities, identifying those more sensible to increasing of market concentration, revealing strategies of vertical integration which can rise the dependence grade of the petroleum companies close to their suppliers. So, this paper evaluates the evolution of the interface among the petroleum and the para-petroleum, identifying the following aspects: the variables that can modify the organizational structure of the agents, the strategies of the service enterprises to act in a environment of elevated dynamism in his structure and competition grade, the strategies of the operators with government participation related to the para-petroleum enterprise businesses, and the consolidation of the sector leader of the service sector and his search for integration.

  16. Production and refining. Increase of Chinese petroleum imports

    International Nuclear Information System (INIS)

    Anon.

    1997-01-01

    China produced 156.5 Mt of petroleum in 1996, from which 56 Mt were extracted from the Daqing oil field, exploited since 1960. About 10% of the crude oil comes from offshore fields. Over the 100 Mt refined in 1996, 20 Mt were imported. The Chinese petroleum products demand should increase to 200 Mt/y by the end of the century with respect to 150 Mt/y in 1997. The Dalian refinery, the first Chinese-foreign joint venture, started to work in November 1996 and should reached its full capacity of 100000 b/day in the first quarter of 1997. The Chinese refining activity has now an excess capacity of 206 Mt/y. Several other joint venture projects in petrochemistry are planned in China. Short paper. (J.S.)

  17. Long term mineralogical changes in salt formations due to water and brine interactions

    International Nuclear Information System (INIS)

    Herbert, H.J.; Brewitz, W.

    1996-01-01

    Four very common long term mineralogical changes in salt formations are discussed in the view of the safety considerations for underground repositories. Two of these processes, the 'Hartsalz' and 'Carnallite' dissolution were studied in two scale in situ experiments. The results are presented and compared with the results of the geochemical modelling with the computer code EQ3/6. Furthermore the reactions leading to the formation of the gypsum cap rock on the top of the Zechstein salt formations and to the polyhalitization of anhydrite are discussed. Geological field observations and mineral assemblages agree well with the results of the geochemical modelling employing the Pitzer formalism along with the Harvie, Moller and Weare database. We conclude that once the mechanisms of the chemical reactions are well understood it becomes possible to evaluate realistically whether such processes, when encountered in the repository, are still active or whether they are finished. It also becomes possible to estimate the volume changes associated with the reactions and thus the impact of these reactions on the integrity and the geomechanical stability of the salt formation. The intimate knowledge of the reaction mechanisms of the short and long term changes in the mineralogical assemblages and the associated brine chemistry is a first prerequisite for the correct evaluation of the origin of brines. Thus, it is essential for the correct assessment of the hazards which brine inflows may pose for the safety of a repository in salt formations. (authors). 8 refs., 14 figs., 8 tabs

  18. Petroleum price

    International Nuclear Information System (INIS)

    Chevallier, B.

    2009-01-01

    The 'AFTP' conference on 'petroleum prices' organized by Total last March, tries to explain the different aspects of the crisis we undergo for July 2007 and its consequential effects on the petroleum markets (supply, demand evolvements, impacts on reserves, prices, refining...). (O.M.)

  19. A deep sea community at the Kebrit brine pool in the Red Sea

    KAUST Repository

    Vestheim, Hege; Kaartvedt, Stein

    2015-01-01

    Approximately 25 deep sea brine pools occur along the mid axis of the Red Sea. These hypersaline, anoxic, and acidic environments have previously been reported to host diverse microbial communities. We visited the Kebrit brine pool in April 2013

  20. Biosurfactants: Promising Molecules for Petroleum Biotechnology Advances

    Directory of Open Access Journals (Sweden)

    DARNE GERMANO DE ALMEIDA

    2016-10-01

    Full Text Available The growing global demand for sustainable technologies that improves the efficiency of petrochemical processes in the oil industry has driven advances in petroleum biotechnology in recent years. Petroleum industry uses substantial amounts of petrochemical-based synthetic surfactants in its activities as mobilizing agents to increase the availability or recovery of hydrocarbons as well as many other applications related to extraction, treatment, cleaning and transportation. However, biosurfactants have several potential applications for use across the oil processing chain and in the formulations of petrochemical products such as emulsifying/demulsifying agents, anticorrosive, biocides for sulphate-reducing bacteria, fuel formulation, extraction of bitumen from tar sands and many other innovative applications. Due to their versatility and proven efficiency, biosurfactants are often presented as valuable versatile tools that can transform and modernise petroleum biotechnology in an attempt to provide a true picture of state of the art and directions or use in the oil industry. We believe that biosurfactants are going to have a significant role in many future applications in the oil industries and in this review therefore, we highlight recent important relevant applications, patents disclosures and potential future applications for biosurfactants in petroleum and related industries.

  1. Biosurfactants: Promising Molecules for Petroleum Biotechnology Advances.

    Science.gov (United States)

    De Almeida, Darne G; Soares Da Silva, Rita de Cássia F; Luna, Juliana M; Rufino, Raquel D; Santos, Valdemir A; Banat, Ibrahim M; Sarubbo, Leonie A

    2016-01-01

    The growing global demand for sustainable technologies that improves the efficiency of petrochemical processes in the oil industry has driven advances in petroleum biotechnology in recent years. Petroleum industry uses substantial amounts of petrochemical-based synthetic surfactants in its activities as mobilizing agents to increase the availability or recovery of hydrocarbons as well as many other applications related to extraction, treatment, cleaning, and transportation. However, biosurfactants have several potential applications for use across the oil processing chain and in the formulations of petrochemical products such as emulsifying/demulsifying agents, anticorrosive, biocides for sulfate-reducing bacteria, fuel formulation, extraction of bitumen from tar sands, and many other innovative applications. Due to their versatility and proven efficiency, biosurfactants are often presented as valuable versatile tools that can transform and modernize petroleum biotechnology in an attempt to provide a true picture of state of the art and directions or use in the oil industry. We believe that biosurfactants are going to have a significant role in many future applications in the oil industries and in this review therefore, we highlight recent important relevant applications, patents disclosures and potential future applications for biosurfactants in petroleum and related industries.

  2. Biosurfactants: Promising Molecules for Petroleum Biotechnology Advances

    Science.gov (United States)

    De Almeida, Darne G.; Soares Da Silva, Rita de Cássia F.; Luna, Juliana M.; Rufino, Raquel D.; Santos, Valdemir A.; Banat, Ibrahim M.; Sarubbo, Leonie A.

    2016-01-01

    The growing global demand for sustainable technologies that improves the efficiency of petrochemical processes in the oil industry has driven advances in petroleum biotechnology in recent years. Petroleum industry uses substantial amounts of petrochemical-based synthetic surfactants in its activities as mobilizing agents to increase the availability or recovery of hydrocarbons as well as many other applications related to extraction, treatment, cleaning, and transportation. However, biosurfactants have several potential applications for use across the oil processing chain and in the formulations of petrochemical products such as emulsifying/demulsifying agents, anticorrosive, biocides for sulfate-reducing bacteria, fuel formulation, extraction of bitumen from tar sands, and many other innovative applications. Due to their versatility and proven efficiency, biosurfactants are often presented as valuable versatile tools that can transform and modernize petroleum biotechnology in an attempt to provide a true picture of state of the art and directions or use in the oil industry. We believe that biosurfactants are going to have a significant role in many future applications in the oil industries and in this review therefore, we highlight recent important relevant applications, patents disclosures and potential future applications for biosurfactants in petroleum and related industries. PMID:27843439

  3. Design of Tomato Drying System by Utilizing Brine Geothermal

    Science.gov (United States)

    Afuar, W.; Sibarani, B.; Abdurrahman, G.; Hendrarsakti, J.

    2016-09-01

    Cultivation of tomato plants in Indonesia has been started since 1961.Tomatoes generally will rot in three days if left on storage. Moreover, low quality tomatoes have cheaper price. After harvested, tomatoes need to be treated by drying process so it can last longer. Energy for drying tomatoes can be obtained by utilizing heat from geothermal brine. Purpose of this research is to design a tomato drying system by extracting heat of geothermal brine from separator with certain flow rate to heat up water by using a heat exchanger. Furthermore, this water will be used to heat up the surrounding air which is circulated by blower system to heat up the tomatoes chamber. Tomatoes drying process needs temperature range of 50-70°C to evaporate water content from 95.7% to 26%. After that treatment, the tomatoes are expected to have better durability. The objective of this study is to determine the quantity of hot brine which is needed for drying tomatoes and to design a drying system so that tomatoes can last longer.

  4. The petroleum resources on the Norwegian Continental Shelf. 2009

    Energy Technology Data Exchange (ETDEWEB)

    2009-07-01

    Exploration activity has reached record-breaking levels in the last couple of years, which has led to many, but small, discoveries. The NPD believes that large discoveries can still be made in areas of the shelf that have not been extensively explored. Content: Challenges on the Norwegian continental shelf; Value creation in fields; 40 years of oil and gas production; Resource management; Still many possibilities; Energy consumption and the environment; Exploration; Access to acreage; Awards of new licenses; Exploration in frontier areas; Exploration history and statistics; Resources and forecasts; Undiscovered resources; Proven recoverable resources; Forecasts; Short-term petroleum production forecast (2009-2013); Investments- and operating costs forecasts; Long-term forecast for the petroleum production; Emissions from the petroleum activity. (AG)

  5. Microbiological evaluation on toxicity amelioration of soil samples contaminated with petroleum-based products

    International Nuclear Information System (INIS)

    Khairuddin Abdul Rahim; Pauline Liew Woan Ying; Ahmad Nazrul Abd Wahid; Shamsiah Abdul Rahman; Mohd Suhaimi Hamzah; Abdul Khalik Wood; Muhamat Omar

    2004-01-01

    Samples of soil materials from oil sludge landfarm in Melaka and petroleum sludge ready for disposal were analysed on their potentially toxic elements and compounds and their microbial population. These were compared against uncontaminated soil samples from agricultural plots and fresh crude petroleum samples obtained from an oil refinery in Kerteh, Terengganu. Enumeration and isolation of culturable microbial populations in the above samples were conducted using standard plate counts and screening methods. Populations of microorganisms from uncontaminated soils were tested on its potential to degrade petroleum derived products on contaminated soil samples and crude petroleum samples in a laboratory experiment. Microorganisms with great potential to degrade petroleum sludge will be further screened in further bioremediation studies in the field. (Author)

  6. 77 FR 56421 - Standards of Performance for Petroleum Refineries; Standards of Performance for Petroleum...

    Science.gov (United States)

    2012-09-12

    ... Parts 9 and 60 Standards of Performance for Petroleum Refineries; Standards of Performance for Petroleum...-9672-3] RIN 2060-AN72 Standards of Performance for Petroleum Refineries; Standards of Performance for Petroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After May 14, 2007...

  7. A Dual-Continuum Model for Brine Migration in Salt Associated with Heat-Generating Nuclear Waste: Fully Coupled Thermal-Hydro-Mechanical Analysis

    Science.gov (United States)

    Hu, M.; Rutqvist, J.

    2017-12-01

    The disposal of heat-generating nuclear waste in salt host rock establishes a thermal gradient around the waste package that may cause brine inclusions in the salt grains to migrate toward the waste package. In this study, a dual-continuum model is developed to analyze such a phenomenon. This model is based on the Finite Volume Method (FVM), and it is fully thermal-hydro-mechanical (THM) coupled. For fluid flow, the dual-continuum model considers flow in the interconnected pore space and also in the salt grains. The mass balance of salt and water in these two continua is separately established, and their coupling is represented by flux associated with brine migration. Together with energy balance, such a system produces a coupled TH model with strongly nonlinear features. For mechanical analysis, a new formulation is developed based on the Voronoi tessellated mesh. By relating each cell to several connected triangles, first-order approximation is constructed. The coupling between thermal and mechanical fields is only considered in terms of thermal expansion. And the coupling between the hydraulic and mechanical fields in terms of pore-volume effects is consistent with Biot's theory. Therefore, a fully coupled THM model is developed. Several demonstration examples are provided to verify the model. Last the new model is applied to analyze coupled THM behavior and the results are compared with experimental data.

  8. Successful field tests of a multi-process phytoremediation system for decontamination of persistent petroleum and organic contaminants

    Energy Technology Data Exchange (ETDEWEB)

    Greenberg, B.M.; Huang, X.D.; Gurska, Y.; Gerhardt, K.E.; Wang, W.; Lampi, M.A.; Zhang, C.; Khalid, A.; Isherwood, D.; Chang, P.; Wang, H.; Dixon, D.G.; Glick, B.R. [Waterloo Univ., ON (Canada)

    2006-07-01

    A large number of aquatic and terrestrial environments are polluted with various levels of toxicants. Metals, organics and total petroleum hydrocarbons from anthropogenic sources pose a risk to both human health and the health of ecosystems. Although these persistent contaminants are difficult to remediate, several industrial sites throughout North America are being remediated as part of land reclamation and restoration programs. This paper addressed the issue of phytoremediation for removing contaminants from soils. Phytoremediation is considered to be a viable remediation strategy because the increased biomass of plants, relative to the biomass of soil microbes in the absence of plants, allows for higher throughput. Extensive root systems can infiltrate large volumes of soil, thus promoting degradation of contaminants over a wide area. This paper described a newly developed multi-process phytoremediation system with accelerated remediation kinetics to effectively remove polycyclic aromatic hydrocarbons (PAH), total petroleum hydrocarbons (TPH) and chlorinated hydrocarbons (CHC) from soils. The system combines land farming/sunlight exposure; inoculation of contaminant degrading bacteria; and, plant growth with plant growth promoting rhizobacteria which mitigates the effects of stress ethylene in plants. The primary factor for success was the interaction between the plant and the plant growth promoting rhizobacteria. Several field tests were conducted following successful greenhouse tests. Results at a TPH contaminated site in Sarnia, Ontario showed that over a 2 year period, 60 to 70 per cent remediation of 15 per cent TPH was achieved. At a site in Turner Valley, Alberta, 35 per cent remediation of 1 per cent recalcitrant TPH was achieved, while a DDT contaminated site near Simcoe, Ontario had nearly 30 per cent of CHC removed in a 3 month period. 34 refs., 2 tabs., 2 figs.

  9. Successful field tests of a multi-process phytoremediation system for decontamination of persistent petroleum and organic contaminants

    International Nuclear Information System (INIS)

    Greenberg, B.M.; Huang, X.D.; Gurska, Y.; Gerhardt, K.E.; Wang, W.; Lampi, M.A.; Zhang, C.; Khalid, A.; Isherwood, D.; Chang, P.; Wang, H.; Dixon, D.G.; Glick, B.R.

    2006-01-01

    A large number of aquatic and terrestrial environments are polluted with various levels of toxicants. Metals, organics and total petroleum hydrocarbons from anthropogenic sources pose a risk to both human health and the health of ecosystems. Although these persistent contaminants are difficult to remediate, several industrial sites throughout North America are being remediated as part of land reclamation and restoration programs. This paper addressed the issue of phytoremediation for removing contaminants from soils. Phytoremediation is considered to be a viable remediation strategy because the increased biomass of plants, relative to the biomass of soil microbes in the absence of plants, allows for higher throughput. Extensive root systems can infiltrate large volumes of soil, thus promoting degradation of contaminants over a wide area. This paper described a newly developed multi-process phytoremediation system with accelerated remediation kinetics to effectively remove polycyclic aromatic hydrocarbons (PAH), total petroleum hydrocarbons (TPH) and chlorinated hydrocarbons (CHC) from soils. The system combines land farming/sunlight exposure; inoculation of contaminant degrading bacteria; and, plant growth with plant growth promoting rhizobacteria which mitigates the effects of stress ethylene in plants. The primary factor for success was the interaction between the plant and the plant growth promoting rhizobacteria. Several field tests were conducted following successful greenhouse tests. Results at a TPH contaminated site in Sarnia, Ontario showed that over a 2 year period, 60 to 70 per cent remediation of 15 per cent TPH was achieved. At a site in Turner Valley, Alberta, 35 per cent remediation of 1 per cent recalcitrant TPH was achieved, while a DDT contaminated site near Simcoe, Ontario had nearly 30 per cent of CHC removed in a 3 month period. 34 refs., 2 tabs., 2 figs

  10. Photolysis of petroleum

    International Nuclear Information System (INIS)

    Bobra, M.

    1992-05-01

    A study was conducted to examine the chemical and physical changes that occur in oils as a result of photooxidation. A literature review of recent studies in petroleum photochemistry revealed reported effects of photo-induced reactions in petroleum, including changes in color, polymerization, solidification, increases in solubility and toxicity, and changes in interfacial properties. A list of products reported as a result of photolysis of petroleum is presented, including such compounds as aldehydes, ketones, esters, and lactones. The photoreactivity of various petroleum components is discussed and mechanisms of photooxidation of petroleum are suggested. In the experimental portion of the study, a variety of crude oils and petroleum products were used to determine how different oils are affected by photolysis, and to examine the importance of photolysis as a weathering process. Photooxidation products from several oils were isolated and identified, including aliphatic and aromatic acids, alcohols, and phenols. Some physical manifestations attributed to photolysis included yellowing, formation of precipitates or crusts, increases in density and viscosity with time, increases of asphaltene content in some oils, changes in pH of the surrounding water, and emulsification. 51 refs., 38 figs., 18 tabs

  11. Petroleum supply monthly, January 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-01

    Data presented describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States. The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  12. Interfacial tension measurement between CO2 and brines under high temperature and elevated pressure conditions

    Science.gov (United States)

    Li, X.; Boek, E. S.; Maitland, G. C.; Trusler, J. P. M.

    2012-04-01

    We have investigated the dependence of interfacial tension of (CO2 + brine) on temperature, pressure and salinity (including both salt type and molality) over the range of conditions applicable to CO2 storage in saline aquifers. The study covered a wide range of measurements of the interfacial tensions between carbon dioxide and (NaCl + KCl)(aq), CaCl2(aq), MgCl2(aq), Na2SO4(aq), KHCO3(aq), NaHCO3(aq) and two laboratory constructed brines with molality ranging from (0.3 to 5.0) mol·kg-1. The measurements were made at temperatures between (298 and 448) K at various pressures up to 50 MPa, using the pendant drop method in a high-pressure view cell filled with water-saturated CO2. The drop to be imaged was created by injecting brine from a high-pressure syringe pump into a capillary sealed through the top of the cell. The expanded uncertainties of the experimental state variables at 95 % confidence are +0.05 K in temperature and +70 kPa in pressure. For the interfacial tension, the overall expanded relative uncertainty at 95 % confidence was +1.6%. The experimental results show that interfacial tension for all the systems increases linearly with molality, indicating that relatively few measurements and simple interpolation procedures are adequate for describing this property accurately over wide ranges of conditions.

  13. Petroleum marketing monthly, July 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-07-01

    The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in five sections: summary statistics; crude oil prices; prices of petroleum products; volumes of petroleum products; and prime supplier sales volumes of petroleum products for local consumption. 7 figs., 50 tabs.

  14. Petroleum supply monthly, August 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-08-26

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics.

  15. Bioremediation of hydrocarbon and brine contaminated topsoil : annual report (1992-93)

    International Nuclear Information System (INIS)

    Danielson, R.M.

    1996-01-01

    This report presents the results of a study which examined the remediation of hydrocarbon and brine contaminated topsoil in a field-based bioreactor at a gas processing plant in Nevis, Alberta during 1992 and 1993. The hydrocarbon and brine contaminated topsoil was placed in the Bio-Reactor and treated for eleven months. Four treatments were applied to eight Bio-Reactor cells: (1) ambient temperature/no forced aeration, (2) ambient temperature/forced aeration, (3) optimum temperature/no forced aeration and (4) optimum temperature/forced aeration. The ninth cell was filled with 30 cm contaminated topsoil and maintained under optimum temperature/forced aeration. The contaminated topsoil was kept moist throughout the experiment by an automatic irrigation system. The contaminated topsoil in the heated cells lost 40 per cent of its original hydrocarbon content in one year; the soil in the non-heated cells lost between 25 and 29 per cent in the same period. Results showed that the Bio-Reactor offered an inexpensive means for promoting a natural process for degrading organic compounds by microorganisms in soil. Equally important, it is capable of handling the large volumes of waste produced by the oil and gas industry. 64 refs., 35 tabs., 46 figs

  16. Strategic Petroleum Reserve Site Environmental Report for calendar year 1994

    International Nuclear Information System (INIS)

    1995-01-01

    The purpose of this Site Environmental Report (SER) is to characterize site environmental management performance, confirm compliance with environmental standards and requirements, and highlight significant programs and efforts. The SER, provided annually in accordance with Department of Energy DOE Order 5400.1, serves the public by summarizing monitoring data collected to assess how the Strategic Petroleum Reserve (SPR) impacts the environment. This report (SER) provides a balanced synopsis of non-radiological monitoring and regulatory compliance data and affirms that the SPR has been operating within acceptable regulatory limits. Included in this report is a description of each site's environment, an overview of the SPR environmental program, and a recapitulation of special environmental activities and events associated with each SPR site during 1994. Two of these highlights include decommissioning of the Weeks Island facility (disposition of 73 million barrels of crude oil inventory) as well as the degasification of up to 144 million barrels of crude oil inventory at the Bayou Choctaw, Big Hill, Bryan Mound, and West Hackberry facilities. The decision to decommission the Weeks Island facility is a result of diminishing mine integrity from ground water intrusion. Degasifying the crude oil is required to reduce potentially harmful emissions that would occur during oil movements. With regard to still another major environmental action, 43 of the original 84 environmental findings from the 1992 DOE Tiger Team Assessment were closed by the end of 1994. Spills to the environment, another major topic, indicates a positive trend. Total volume of oil spilled in 1994 was only 39 barrels, down from 232 barrels in 1993, and the total volume of brine spilled was only 90 barrels, down from 370 barrels in 1993. The longer term trend for oil and brine spills has declined substantially from 27 in 1990 down to nine in 1994

  17. 46 CFR 148.04-15 - Petroleum coke, uncalcined; petroleum coke, uncalcined and calcined (mixture).

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Petroleum coke, uncalcined; petroleum coke, uncalcined and calcined (mixture). 148.04-15 Section 148.04-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND... Requirements for Certain Material § 148.04-15 Petroleum coke, uncalcined; petroleum coke, uncalcined and...

  18. Salted herring brine as a coating or additive for herring (Clupea harengus) products — A source of natural antioxidants?

    DEFF Research Database (Denmark)

    Albertos, Irene; Gringer, Nina; Rico, Daniel

    2016-01-01

    The objective of this study was to characterise herring brine and assess its use as natural antioxidant in herring preservation. Herring brines from different marinated products (brine from fillet-ripened spice-cured herring SC, traditional barrel-salted spice-cured herring TSp and brine from...

  19. Petroleum and geopolitics

    International Nuclear Information System (INIS)

    Chaigneau, P.

    2004-01-01

    Todays, petroleum companies consider that despite the constant increase of petroleum consumption, petroleum will remain the main energy source for at least 40 years. However, after the Iraq conflict, new regional situations are changing. China, for instance, with its growing up demand, will change the physiognomy of the oil market. In parallel, from Indonesia to Africa, petroleum and religion interfere and explain the new conflict areas. As for the US strategy, which is not limited to the energy paradigm, it largely integrates energy in the main lines of its diplomacy, from the 'Wide Middle East' to the 'Sahel initiative', and in its position with respect to Venezuela

  20. Review of the impacts of leaking CO 2 gas and brine on groundwater quality

    Energy Technology Data Exchange (ETDEWEB)

    Qafoku, Nikolla P.; Lawter, Amanda R.; Bacon, Diana H.; Zheng, Liange; Kyle, Jennifer; Brown, Christopher F.

    2017-06-01

    This review paper provides a synthetic view of the existing knowledge and summarizes data and findings of the recent literature on the subject of the potential leaking of CO2 from the deep subsurface storage reservoirs and the effects on aquifer quality. New ideas and concepts are developed and insights are also provided. The objectives of this paper are to: 1) present and discuss potential risks for groundwater degradation due to CO2 gas and brine exposure; 2) identify the set of geochemical data required to assess and predict aquifer responses to CO2 and brine leakage. Specifically, this paper will discuss the following issues: 1) Aquifer responses (such as changes in aqueous phase/groundwater chemical composition; changes in solid phase chemistry and mineralogy; changes in the extent and rate of reactions and processes and possible establishment of a new network of reactions and processes affecting or controlling overall mobility of major, minor, and trace elements; development of conceptual and reduced order models (ROMs) to describe and predict aquifer responses); 2) The degree of impact such as significant or insignificant changes in pH and major, minor, and trace element release that depend on the following controlling variables; the effect of leaking plume characteristics (gas composition, pure CO2 and/or CO2 -CH4 -H2S mixtures and brine concentration and composition (trace metals); aquifer properties [such as initial aqueous phase conditions and mineralogy: minerals controlling sediments’ response (e.g., calcite, Si bearing minerals, etc.)]; overview of relevant hydrogeological and geochemical processes related to the impact of CO2 gas and brine on groundwater quality; the fate of the elements released from sediments or transported with brine (such as precipitation/incorporation into minerals (calcite and other minerals), adsorption, electron transfer reactions, the role of natural attenuation; whether or not the release of metals following exposure to

  1. Comparison of the Sr isotopic signatures in brines of the Canadian and Fennoscandian shields

    International Nuclear Information System (INIS)

    Negrel, Philippe; Casanova, Joel

    2005-01-01

    A synthesis of Sr isotope data from shallow and deep groundwaters, and brines from the Fennoscandian and Canadian Shields is presented. A salinity gradient is evident in the water with concentrations varying from approximately 1-75 g L -1 below 1500 m depth in the Fennoscandian Shield and from 10 up to 300 g L -1 below 650 m depth in the Canadian Shield. Strontium isotope ratios were measured to assess the origin of the salinity and evaluate the degree of water-rock interaction in the systems. In both shields, the Sr concentrations are enriched relative to Cl, defining a positive trend parallel to the seawater dilution line and indicative of Sr addition through weathering processes. The depth distribution for Sr concentration increases strongly with increasing depth in both shields although the variation in Sr-isotope composition does not mirror that of Sr concentrations. Strontium-isotope compositions are presented for surface waters, and groundwaters in several sites in the Fennoscandian and Canadian Shields. Numerous mixing lines can be drawn reflecting water-rock interaction. A series of calculated lines links the surface end-members (surface water and shallow groundwater) and the deep brines; these mixing lines define a range of 87 Sr/ 86 Sr ratios for the deep brines in different selected sites. All sites show a specific 87 Sr/ 86 Sr signature and the occurrence of large 87 Sr/ 86 Sr variations is site specific in both shields. In Canadian Shield brines, the Sr isotope ratios clearly highlight large water rock interaction that increases the 87 Sr/ 86 Sr ratio from water that could have been of marine origin. In contrast to the Canadian Shield, groundwater does not occur in closed pockets in the Fennoscandian, and the well-constrained 87 Sr/ 86 Sr signatures in deep brines should correspond to a large, well-mixed and homogeneous water reservoir, whose Sr isotope signature results from water-rock interaction

  2. Accessible reactive surface area and abiotic redox reactivity of iron oxyhydroxides in acidic brines

    Science.gov (United States)

    Strehlau, Jennifer H.; Toner, Brandy M.; Arnold, William A.; Penn, R. Lee

    2017-01-01

    The reactivity of iron oxyhydroxide nanoparticles in low pH and high ionic strength solutions was quantified to assess abiotic contributions to oxidation-reduction chemistry in acidic brine environments, such as mine groundwater seepage, lakes in Western Australia, and acid mine drainage settings, which are of global interest for their environmental impacts and unique geomicrobiology. Factors expected to influence accessible and reactive surface area, including Fe(II) adsorption and aggregate size, were measured as a function of pH and CaCl2 concentration and related to the kinetics of redox reactions in aqueous suspensions of synthetic goethite (α-FeOOH), akaganeite (β-FeOOH), and ferrihydrite (Fe10O14(OH)2) nanoparticles. Aqueous conditions and iron oxyhydroxides were chosen based on characterization of natural iron-rich mine microbial mats located in Soudan Underground Mine State Park, Minnesota, USA. Quinone species were used as redox sensors because they are well-defined probes and are present in natural organic matter. Fe(II) adsorption to the iron oxyhydroxide mineral surfaces from aqueous solution was measurable only at pH values above 4 and either decreased or was not affected by CaCl2 concentration. Concentrations at or above 0.020 M CaCl2 in acetate buffer (pH 4.5) induced particle aggregation. Assessment of Fe(II) adsorption and particle aggregation in acidic brine suggested that accessible reactive surface area may be limited in acidic brines. This was supported by observations of decreasing benzoquinone reduction rate by adsorbed Fe(II) at high CaCl2 concentration. In contrast, the hydroquinone oxidation rate increased at high CaCl2 concentrations, which may be due to suppressed adsorption of Fe(II) generated by the reaction. Results suggest that iron geochemical cycling in acidic brine environments will be substantially different than for iron oxyhydroxides in low-saline waters with circumneutral pH. These findings have implications for acidic

  3. Indoor tests to investigate the effect of brine depth on the performance of solar still

    Energy Technology Data Exchange (ETDEWEB)

    Ali, Marwah A.W.; Jabbar N. Khalifa, Abdul [Nahrain University, College of Engineering, Jadiriya, P.O. Box 64040, Baghdad (Iraq)

    2013-07-01

    Many experimental and numerical studies have been done on different configurations of solar stills to optimize the design by examining the effect of climatic, operational and design parameters on its performance. One of the most important of the operational parameters that has received a considerable attention in the literature is the brine depth. This paper reports indoor experimental investigations on the effect of brine depth on the productivity and efficiency of the solar stills at four different brine depths of 1.5, 2, 4 and 5.5 cm. Indoor tests were used by simulating the solar input by proper electric heaters located at the bottom of the still for heating the water contained in the basin of the still. The present study validated the decreasing trend in productivity with the increase of brine depth and showed that the still productivity could be influenced by the brine depth by up to 24%.

  4. Bioremediation of Petroleum and Radiological Contaminated Soils at the Savannah River Site: Laboratory to Field Scale Applications

    Energy Technology Data Exchange (ETDEWEB)

    BRIGMON, ROBINL.

    2004-06-07

    In the process of Savannah River Site (SRS) operations limited amounts of waste are generated containing petroleum, and radiological contaminated soils. Currently, this combination of radiological and petroleum contaminated waste does not have an immediate disposal route and is being stored in low activity vaults. SRS developed and implemented a successful plan for clean up of the petroleum portion of the soils in situ using simple, inexpensive, bioreactor technology. Treatment in a bioreactor removes the petroleum contamination from the soil without spreading radiological contamination to the environment. This bioreactor uses the bioventing process and bioaugmentation or the addition of the select hydrocarbon degrading bacteria. Oxygen is usually the initial rate-limiting factor in the biodegradation of petroleum hydrocarbons. Using the bioventing process allowed control of the supply of nutrients and moisture based on petroleum contamination concentrations and soil type. The results of this work have proven to be a safe and cost-effective means of cleaning up low level radiological and petroleum-contaminated soil. Many of the other elements of the bioreactor design were developed or enhanced during the demonstration of a ''biopile'' to treat the soils beneath a Polish oil refinery's waste disposal lagoons. Aerobic microorganisms were isolated from the aged refinery's acidic sludge contaminated with polycyclic aromatic hydrocarbons (PAHs). Twelve hydrocarbon-degrading bacteria were isolated from the sludge. The predominant PAH degraders were tentatively identified as Achromobacter, Pseudomonas Burkholderia, and Sphingomonas spp. Several Ralstonia spp were also isolated that produce biosurfactants. Biosurfactants can enhance bioremediation by increasing the bioavailability of hydrophobic contaminants including hydrocarbons. The results indicated that the diversity of acid-tolerant PAH-degrading microorganisms in acidic oil wastes may

  5. Organic geochemistry and brine composition in Great Salt, Mono, and Walker Lakes

    Science.gov (United States)

    Domagalski, Joseph L.; Orem, W.H.; Eugster, H.P.

    1989-01-01

    Samples of Recent sediments, representing up to 1000 years of accumulation, were collected from three closed basin lakes (Mono Lake, CA, Walker Lake, NV, and Great Salt Lake, UT) to assess the effects of brine composition on the accumulation of total organic carbon, the concentration of dissolved organic carbon, humic acid structure and diagenesis, and trace metal complexation. The Great Salt Lake water column is a stratified Na-Mg-Cl-SO4 brine with low alkalinity. Algal debris is entrained in the high density (1.132-1.190 g/cc) bottom brines, and in this region maximum organic matter decomposition occurs by anaerobic processes, with sulfate ion as the terminal electron acceptor. Organic matter, below 5 cm of the sediment-water interface, degrades at a very slow rate in spite of very high pore-fluid sulfate levels. The organic carbon concentration stabilizes at 1.1 wt%. Mono Lake is an alkaline (Na-CO3-Cl-SO4) system. The water column is stratified, but the bottom brines are of lower density relative to the Great Salt Lake, and sedimentation of algal debris is rapid. Depletion of pore-fluid sulfate, near l m of core, results in a much higher accumulation of organic carbon, approximately 6 wt%. Walker Lake is also an alkaline system. The water column is not stratified, and decomposition of organic matter occurs by aerobic processes at the sediment-water interface and by anaerobic processes below. Total organic carbon and dissolved organic carbon concentrations in Walker Lake sediments vary with location and depth due to changes in input and pore-fluid sulfate concentrations. Nuclear magnetic resonance studies (13C) of humic substances and dissolved organic carbon provide information on the source of the Recent sedimentary organic carbon (aquatic vs. terrestrial), its relative state of decomposition, and its chemical structure. The spectra suggest an algal origin with little terrestrial signature at all three lakes. This is indicated by the ratio of aliphatic to

  6. Effects of gamma radiation on the survival and growth of brine shrimp, Artemia salina

    International Nuclear Information System (INIS)

    Engel, D.W.; Davis, E.M.

    1976-01-01

    To determine the effects of gamma radiation on the survival and growth of brine shrimp, nauplii and adults were exposed to different doses of radiation and maintained at different salinities and temperatures. The LD 50 determination demonstrated that nauplii were thirty to forty times more sensitive than the adults and had a 25-day LD 50 of 450 rads. Radiation and salinity reduced survival of adult female brine shrimp more than the males. The interaction of salinity, 5 and 50 ppt, temperature, 10, 20 and 30 0 C, and radiation, 25 to 100 kilorads, decreased the survival of both male and female brine shrimp, with the males having the greater sensitivity. Brine shrimp nauplii irradiated with doses of 500 and 2,500 rads had accelerated growth and matured earlier than the controls. A test of the effect of crowding on growth showed that volume per individual was important, and a dose of 500 rads accelerated brine shrimp growth in all concentrations, with the greatest increase at 8 ml/nauplius

  7. Advective, Diffusive and Eruptive Leakage of CO2 and Brine within Fault Zone

    Science.gov (United States)

    Jung, N. H.; Han, W. S.

    2014-12-01

    This study investigated a natural analogue for CO2 leakage near the Green River, Utah, aiming to understand the influence of various factors on CO2 leakage and to reliably predict underground CO2 behavior after injection for geologic CO2 sequestration. Advective, diffusive, and eruptive characteristics of CO2 leakage were assessed via a soil CO2 flux survey and numerical modeling. The field results show anomalous CO2 fluxes (> 10 g m-2 d-1) along the faults, particularly adjacent to CO2-driven cold springs and geysers (e.g., 36,259 g m-2 d-1 at Crystal Geyser), ancient travertines (e.g., 5,917 g m-2 d-1), joint zones in sandstone (e.g., 120 g m-2 d-1), and brine discharge zones (e.g., 5,515 g m-2 d-1). Combined to similar isotopic ratios of gas and progressive evolution of brine chemistry at springs and geysers, a gradual decrease of soil CO2 flux from the Little Grand Wash (LGW; ~36,259 g m-2 d-1) to Salt Wash (SW; ~1,428 g m-2 d-1) fault zones reveals the same CO2 origin and potential southward transport of CO2 over 10-20 km. The numerical simulations overtly exhibit lateral transport of free CO2 and CO2-rich brine from the LGW to SW fault zones through the regional aquifers (e.g., Entrada, Navajo, Kayenta, Wingate, White Rim). CO2 travels predominantly as an aqueous phase (Xco2=~0.045) as previously suggested, giving rise to the convective instability that further accelerates CO2 dissolution. While the buoyant free CO2 always tends to ascend, a fraction of dense CO2-rich brine flows laterally into the aquifer and mixes with the formation fluids during upward migration along the fault. The fault always enhances advective CO2 transport regardless of its permeability (k). However, only the low-k fault scenario engenders development of CO2 anticlinal trap within the shallow aquifers (Entrada and Navajo), concentrating high CO­­­2 fluxes (~1,273 g m-2 d-1) within the northern footwall of the LGW fault similar to the field. Moreover, eruptive CO2 leakage at a well

  8. Physiological characteristics of bacteria isolated from water brines within permafrost

    Science.gov (United States)

    Shcherbakova, V.; Rivkina, E.; Laurinavichuis, K.; Pecheritsina, S.; Gilichinsky, D.

    2004-01-01

    In the Arctic there are lenses of overcooled water brines (cryopegs) sandwiched within permafrost marine sediments 100 120 thousand years old. We have investigated the physiological properties of the pure cultures of anaerobic Clostridium sp. strain 14D1 and two strains of aerobic bacteria Psychrobacter sp. isolated from these cryopegs. The structural and physiological characteristics of new bacteria from water brines have shown their ability to survive and develop under harsh conditions, such as subzero temperatures and high salinity.

  9. The evaporation of crude oil and petroleum products

    International Nuclear Information System (INIS)

    Fingas, M. F.

    1996-01-01

    The physics of oil and petroleum evaporation was studied by means of an experimental apparatus. The evaporation was determined by weight loss and recorded on a computer. Examination of the data showed that most oil and petroleum products (those with seven to ten components) evaporate at a logarithmic rate with respect to time, while other petroleum products (those with fewer chemical components) evaporate at a rate which is square root with respect to time. Evaporation of oil and petroleum was not strictly boundary-layer regulated because the typical oil evaporation rate rates do not exceed that of molecular diffusion and thus turbulent diffusion does not increase the evaporation rates. Overall, boundary layer regulation can be ignored in the prediction of oil and petroleum evaporation. The simple equation relating only the logarithm of time (or the square root of time in the case of narrow-cut products) and temperature are sufficient to accurately describe oil evaporation. refs., figs

  10. Petroleum Supply Monthly, July 1990

    Energy Technology Data Exchange (ETDEWEB)

    1990-09-28

    Data presented in the PSM describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 states and the District of Columbia). The reporting universe includes those petroleum sectors in Primary Supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States.

  11. Effects of faults as barriers or conduits to displaced brine flow on a putative CO2 storage site in the Southern North Sea

    Science.gov (United States)

    Hannis, Sarah; Bricker, Stephanie; Williams, John

    2013-04-01

    The Bunter Sandstone Formation in the Southern North Sea is a potential reservoir being considered for carbon dioxide storage as a climate change mitigation option. A geological model of a putative storage site within this saline aquifer was built from 3D seismic and well data to investigate potential reservoir pressure changes and their effects on fault movement, brine and CO2 migration as a result of CO2 injection. The model is located directly beneath the Dogger Bank Special Area of Conservation, close to the UK-Netherlands median line. Analysis of the seismic data reveals two large fault zones, one in each of the UK and Netherlands sectors, many tens of kilometres in length, extending from reservoir level to the sea bed. Although it has been shown that similar faults compartmentalise gas fields elsewhere in the Netherlands sector, significant uncertainty remains surrounding the properties of the faults in our model area; in particular their cross- and along-fault permeability and geomechanical behaviour. Despite lying outside the anticipated CO2 plume, these faults could provide potential barriers to pore fluid migration and pressure dissipation, until, under elevated pressures, they provide vertical migration pathways for brine. In this case, the faults will act to enhance injectivity, but potential environmental impacts, should the displaced brine be expelled at the sea bed, will require consideration. Pressure gradients deduced from regional leak-off test data have been input into a simple geomechanical model to estimate the threshold pressure gradient at which faults cutting the Mesozoic succession will fail, assuming reactivation of fault segments will cause an increase in vertical permeability. Various 4D scenarios were run using a single-phase groundwater modelling code, calibrated to results from a multi-phase commercial simulator. Possible end-member ranges of fault parameters were input to investigate the pressure change with time and quantify brine

  12. Recent Advances in Petroleum Microbiology

    Science.gov (United States)

    Van Hamme, Jonathan D.; Singh, Ajay; Ward, Owen P.

    2003-01-01

    Recent advances in molecular biology have extended our understanding of the metabolic processes related to microbial transformation of petroleum hydrocarbons. The physiological responses of microorganisms to the presence of hydrocarbons, including cell surface alterations and adaptive mechanisms for uptake and efflux of these substrates, have been characterized. New molecular techniques have enhanced our ability to investigate the dynamics of microbial communities in petroleum-impacted ecosystems. By establishing conditions which maximize rates and extents of microbial growth, hydrocarbon access, and transformation, highly accelerated and bioreactor-based petroleum waste degradation processes have been implemented. Biofilters capable of removing and biodegrading volatile petroleum contaminants in air streams with short substrate-microbe contact times (desulfurization processes with biodesulfurization methods through promotion of selective sulfur removal without degradation of associated carbon moieties. However, since microbes require an environment containing some water, a two-phase oil-water system must be established to optimize contact between the microbes and the hydrocarbon, and such an emulsion is not easily created with viscous crude oil. This challenge may be circumvented by application of the technology to more refined gasoline and diesel substrates, where aqueous-hydrocarbon emulsions are more easily generated. Molecular approaches are being used to broaden the substrate specificity and increase the rates and extents of desulfurization. Bacterial processes are being commercialized for removal of H2S and sulfoxides from petrochemical waste streams. Microbes also have potential for use in removal of nitrogen from crude oil leading to reduced nitric oxide emissions provided that technical problems similar to those experienced in biodesulfurization can be solved. Enzymes are being exploited to produce added-value products from petroleum substrates, and

  13. Brine migration test - Asse salt mine, Federal Republic of Germany

    International Nuclear Information System (INIS)

    Rothfuchs, T.; Wieczorek, K.; Feddersen, H.K.; Staupendahl, G.; Coyle, A.J.; Kalia, H.; Eckert, J.

    1988-03-01

    This document is the final report on the Cooperative German-American 'Brine Migration Tests' that were performed at the Asse Salt Mine in the Federal Republic of Germany (FRG), the Office of Nuclear Waste Isolation (ONWI), Columbus, Ohio, and the Institut fuer Tieflagerung (IfT), Braunschweig, of the Gesellschaft fuer Strahlen- und Umweltforschung mbH Muenchen (GSF). Final test and equipment design as well as manufacturing and installation was carried out by Westinghouse Electric Corporation. The tests were designed to simulate a nuclear waste repository to measure the effects of heat and gamma radiation on brine migration, salt decrepitation, disassociation of brine, and gases collected. The thermal mechanical behavior of salt, such as room closure, stresses and changes of the properties of salt are measured and compared with predicted behavior. The performance of an array of candidate waste package materials, test equipment and procedures under repository conditions will be evaluated with a view towards future in-depth testing of potential repository sites. (orig./RB)

  14. Fluid inclusion brine compositions from Palo Duro Basin salt sites

    International Nuclear Information System (INIS)

    Moody, J.B.

    1987-01-01

    The fluid inclusion analyses were done on salt samples from Lower San Andres Cycle 4 and 5. The stable isotope composition of the fluid inclusion brines was measured on duplicate samples taken from the same fluid inclusion brine for correlation of geochemical content with the stable isotopic content. The analyzed Palo Duro Basin salt fluid inclusions are predominantly one phase, i.e., the presence of a fluid only. However, many of the larger fluid inclusions do have a small vapor bubble. This liquid/vapor ratio is so high in these vapor-containing fluid inclusions that their behavior in a thermal gradient would be almost identical to that of all liquid inclusions. Closely associated with the fluid inclusions are cryptomelane where some fibers penetrate into halite host crystal. The fluid inclusions have a wide variability in content for those components that were analyzed, even within the same salt type. The fluid inclusion brines are also acidic, ranging from 3 to 6 as measured with pH test papers

  15. Environmental protection: Streamlining petroleum exploration and production

    International Nuclear Information System (INIS)

    Hunt, A.M.

    1991-01-01

    The petroleum industry is inherently subject to a tremendous degree of volatility through fluctuation in world market prices and vagaries of world politics. A more recent stressful demand on the existing domestic petroleum exploration and production system has been the burgeoning number of environmental regulations imposed on this segment of the industry. Prudent and acceptable oil-field practices must now include agency-regulated environmental protection measures. Many independent producers are unfamiliar not only with the regulatory agencies, but also with the jargon and ambiguities, of regulations that very widely from state to state. Whereas some companies perceive only the restrictions and added cost of regulatory compliance, other companies have sought to optimize benefits while minimizing financial burdens by approaching this modern necessity more creatively, thereby discovering numerous means to become even more competitive. The domestic oil field of the 1990s will be increasingly affected by environmental regulation and public opinion. A number of companies have taken a proactive position on environmental issues. Industry examples include Louisiana Land and Exploration Company's history of wetlands conservation and Chevron's SMART (Save Money and Reduce Toxics). The future of the quality of life of this nation, and indeed the planet as a whole, lies in our capability to deal concurrently with the issues of a petroleum-based economy while protecting the natural environment that sustains life

  16. Evaluation of oil removal efficiency and enzymatic activity in some fungal strains for bioremediation of petroleum-polluted soils

    Directory of Open Access Journals (Sweden)

    Mohsenzadeh Fariba

    2012-12-01

    Full Text Available Abstract Background Petroleum pollution is a global disaster and there are several soil cleaning methods including bioremediation. Methods In a field study, fugal strains were isolated from oil-contaminated sites of Arak refinery (Iran and their growth ability was checked in potato dextrose agar (PDA media containing 0-10% v/v crude oil, the activity of three enzymes (Catalase, Peroxidase and Phenol Oxidase was evaluated in the fungal colonies and bioremediation ability of the fungi was checked in the experimental pots containing 3 kg sterilized soil and different concentrations of petroleum (0-10% w/w. Results Four fungal strains, Acromonium sp., Alternaria sp., Aspergillus terreus and Penicillium sp., were selected as the most resistant ones. They were able to growth in the subjected concentrations and Alternaria sp. showed the highest growth ability in the petroleum containing media. The enzyme assay showed that the enzymatic activity was increased in the oil-contaminated media. Bioremediation results showed that the studied fungi were able to decrease petroleum pollution. The highest petroleum removing efficiency of Aspergillus terreus, Penicillium sp., Alternaria sp. and Acromonium sp. was evaluated in the 10%, 8%, 8% and 2% petroleum pollution respectively. Conclusions Fungi are important microorganisms in decreasing of petroleum pollution. They have bioremediation potency that is related to their enzymatic activities.

  17. Petroleum and natural gas economy in Arab countries, Iran, Ethiopia, Nigeria and Somalia

    International Nuclear Information System (INIS)

    1993-01-01

    This paper describes briefly main informations on petroleum prices and market trends, trade and contracts, petroleum exploration and new discovery in Algeria and Libya, birth of a joint venture for the building of a gas pipeline between Ukraine and Europe. The building of another pipeline, between Algeria and Europe, will begin in April 1993. Several agreements for oil and gas fields development in Qatar, Egypt, Yemen, United Arab Emirates have been signed. Petroleum industry has criticized energy taxing project in Usa

  18. Integrated management plan for the North Sea and Skagerrak: Status description for the petroleum industry with emphasis on the Norwegian continental shelf; Helhetlig forvaltningsplan for Nordsjoeen og Skagerrak: Statusbeskrivelse for petroleumsvirksomheten med hovedvekt paa norsk sokkel

    Energy Technology Data Exchange (ETDEWEB)

    2010-06-15

    Status description of the petroleum industry covers mainly the Norwegian continental shelf, but it is also given a brief description of the activity in other offshore areas of the North Sea. It shows a list of producing fields, fields under development, developments in the future, findings that are in the planning phase, and completed fields. It also describes the pipelines and other petroleum-related activities at sea and on shore. (AG)

  19. Attempt to enrich of a new spontaneous fissioning nuclide by evaporation of natural brine

    International Nuclear Information System (INIS)

    Adamek, A.; Zhuravleva, E.L.; Constantinescu, M.; Constantinescu, o.; Chuburkov, Yu.T.

    1983-01-01

    The enrichment of the new spontaneous fissioning nuclide discovered in the Cheleken brine, was made by evaporation. The purpose of this work was the comparison of behaviour of the new spontaneous fissioning nuclide with that of the known elements in the formation processes of the high concentration brines. Spontaneous fission of the nuclide was measured by means of the counters for multiple emission of neutrons. It is shown that the new spontaneous fissioning nuclide was enriched as well as other trace elements (Hg, Tl, Bi and Pb) in a solution remained after the evaporation of the initial solution. The conclusion is drawn that from the sea water brines could be obtained by evaporation which are enriched in trace elements with an enrichment degree higher than the natural brines

  20. Proceedings of the Canadian International Petroleum Conference 2005 and the 56. Annual Technical Meeting of the Petroleum Society of CIM : Because Technology Changes Everything. CD ed.

    International Nuclear Information System (INIS)

    2005-01-01

    This conference and trade show outlined the latest technologies associated with hydrocarbon exploration, petroleum geology, resource development, and enhanced recovery. It was attended by local and international participants in the petroleum sector. The 31 sessions highlighted the challenges facing the petroleum industry in terms of maturing basins and focused on issues such as business development and risk management; cold production of heavy oil; health, safety and regulatory issues; and environmental concerns regarding oil and gas development. The presentations were targeted for managers, engineers, technologists, geologists, and other petroleum industry specialists dealing with topical issues such as: well completion; well stimulation; well test analysis; thermal recovery; reservoir characterization; fluid characterization; numerical simulation; computerized simulation; emerging technology; thermal field projects; production operations; business development; and refining facilities. A total of 122 papers have been catalogued separately for inclusion in this database. (author)

  1. Petroleum marketing monthly, June 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-06-01

    The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. Monthly statistics on purchases of crude oil and sales of petroleum products are presented in five sections: Summary Statistics; Crude Oil Prices; Prices of Petroleum Products; Volumes of Petroleum Products; and Prime Supplier Sales Volumes of Petroleum Products for Local Consumption. The feature article is entitled ``The Second Oxygenated Gasoline Season.`` 7 figs., 50 tabs.

  2. Selective Recovery of Metals from Geothermal Brines

    Energy Technology Data Exchange (ETDEWEB)

    Ventura, Susanna [SRI International, Menlo Park, CA (United States); Bhamidi, Srinivas [SRI International, Menlo Park, CA (United States); Hornbostel, Marc [SRI International, Menlo Park, CA (United States); Nagar, Anoop [SRI International, Menlo Park, CA (United States); Perea, Elisabeth [SRI International, Menlo Park, CA (United States)

    2016-12-16

    The objective of this project was to determine the feasibility of developing a new generation of highly selective low-cost ion-exchange resins based on metal-ion imprinted polymers for the separation of metals from geothermal fluids. Expansion of geothermal energy production over the entire U.S. will involve exploitation of low-to-medium temperature thermal waters. Creating value streams from the recovery of critical and near-critical metals from these thermal waters will encourage geothermal expansion. Selective extraction of metals from geothermal fluids is needed to design a cost-effective process for the recovery of lithium and manganese-two near-critical metals with well-known application in the growing lithium battery industry. We have prepared new lithium- and manganese-imprinted polymers in the form of beads by crosslinking polymerization of a metal polymerizable chelate, where the metal acts as a template. Upon leaching out the metal template, the crosslinked polymer is expected to leave cavities defined by the ligand functional group with enhanced selectivity for binding the template metal. We have demonstrated that lithium- and manganese-imprinted polymer beads can be used as selective solid sorbents for the extraction of lithium and manganese from brines. The polymers were tested both in batch extractions and packed bed lab-scale columns at temperatures of 45-100°C. Lithium-imprinted polymers were found to have Li+ adsorption capacity as high as 2.8 mg Li+/g polymer at 45°C. Manganese-imprinted polymers were found to have a Mn2+ adsorption capacity of more than 23 mg Mn2+/g polymer at 75°C. The Li+ extraction efficiency of the Li-imprinted polymer was found to be more that 95% when a brine containing 390 ppm Li+, 410 ppm Na+, and 390 ppm K+ was passed through a packed bed of the polymer in a lab-scale column at 45°C. In brines containing 360 ppm Li

  3. Distinctive Microbial Community Structure in Highly Stratified Deep-Sea Brine Water Columns

    KAUST Repository

    Bougouffa, Salim; Yang, J. K.; Lee, O. O.; Wang, Y.; Batang, Zenon B.; Al-Suwailem, Abdulaziz M.; Qian, P. Y.

    2013-01-01

    Atlantis II and Discovery are two hydrothermal and hypersaline deep-sea pools in the Red Sea rift that are characterized by strong thermohalo-stratification and temperatures steadily peaking near the bottom. We conducted comprehensive vertical profiling of the microbial populations in both pools and highlighted the influential environmental factors. Pyrosequencing of the 16S rRNA genes revealed shifts in community structures vis-à-vis depth. High diversity and low abundance were features of the deepest convective layers despite the low cell density. Surprisingly, the brine interfaces had significantly higher cell counts than the overlying deep-sea water, yet they were lowest in diversity. Vertical stratification of the bacterial populations was apparent as we moved from the Alphaproteobacteria-dominated deep sea to the Planctomycetaceae- or Deferribacteres-dominated interfaces to the Gammaproteobacteria-dominated brine layers. Archaeal marine group I was dominant in the deep-sea water and interfaces, while several euryarchaeotic groups increased in the brine. Across sites, microbial phylotypes and abundances varied substantially in the brine interface of Discovery compared with Atlantis II, despite the near-identical populations in the overlying deep-sea waters. The lowest convective layers harbored interestingly similar microbial communities, even though temperature and heavy metal concentrations were very different. Multivariate analysis indicated that temperature and salinity were the major influences shaping the communities. The harsh conditions and the low-abundance phylotypes could explain the observed correlation in the brine pools.

  4. Distinctive Microbial Community Structure in Highly Stratified Deep-Sea Brine Water Columns

    KAUST Repository

    Bougouffa, Salim

    2013-03-29

    Atlantis II and Discovery are two hydrothermal and hypersaline deep-sea pools in the Red Sea rift that are characterized by strong thermohalo-stratification and temperatures steadily peaking near the bottom. We conducted comprehensive vertical profiling of the microbial populations in both pools and highlighted the influential environmental factors. Pyrosequencing of the 16S rRNA genes revealed shifts in community structures vis-à-vis depth. High diversity and low abundance were features of the deepest convective layers despite the low cell density. Surprisingly, the brine interfaces had significantly higher cell counts than the overlying deep-sea water, yet they were lowest in diversity. Vertical stratification of the bacterial populations was apparent as we moved from the Alphaproteobacteria-dominated deep sea to the Planctomycetaceae- or Deferribacteres-dominated interfaces to the Gammaproteobacteria-dominated brine layers. Archaeal marine group I was dominant in the deep-sea water and interfaces, while several euryarchaeotic groups increased in the brine. Across sites, microbial phylotypes and abundances varied substantially in the brine interface of Discovery compared with Atlantis II, despite the near-identical populations in the overlying deep-sea waters. The lowest convective layers harbored interestingly similar microbial communities, even though temperature and heavy metal concentrations were very different. Multivariate analysis indicated that temperature and salinity were the major influences shaping the communities. The harsh conditions and the low-abundance phylotypes could explain the observed correlation in the brine pools.

  5. Geochemical evaluation of flowback brine from Marcellus gas wells in Pennsylvania, USA

    International Nuclear Information System (INIS)

    Haluszczak, Lara O.; Rose, Arthur W.; Kump, Lee R.

    2013-01-01

    Large quantities of highly saline brine flow from gas wells in the Marcellus Formation after hydraulic stimulation (“fracking”). This study assesses the composition of these flowback waters from the Marcellus shale in Pennsylvania, USA. Concentrations of most inorganic components of flowback water (Cl, Br, Na, K, Ca, Mg, Sr, Ba, Ra, Fe, Mn, total dissolved solids, and others) increase with time from a well after hydraulic stimulation. Based on results in several datasets reported here, the greatest concentration of Cl − in flowback water is 151,000 mg/L. For total Ra (combined 226 Ra and 228 Ra) in flowback, the highest level reported is 6540 pCi/L. Flowback waters from hydraulic fracturing of Marcellus wells resemble brines produced from conventional gas wells that tap into other Paleozoic formations in the region. The Br/Cl ratio and other parameters indicate that both types of brine formed by the evaporation of seawater followed by dolomitization, sulfate reduction and subsurface mixing with seawater and/or freshwater. Trends and relationships in brine composition indicate that (1) increased salt concentration in flowback is not mainly caused by dissolution of salt or other minerals in rock units, (2) the flowback waters represent a mixture of injection waters with highly concentrated in situ brines similar to those in the other formations, and (3) these waters contain concentrations of Ra and Ba that are commonly hundreds of times the US drinking water standards.

  6. Water Recovery from Brine in the Short and Long Term: A KSC Approach

    Science.gov (United States)

    Lunn, Griffin; Melendez, Orlando; Anthony, Steve

    2014-01-01

    KSC has spent many years researching Hollow Fiber Membrane Bioreactors as well as research encompassing:Alternate ammonia removal/Advanced oxidation. Brine purification technologies KSC-ISRU has built an electrolysis cell for the removal of acids in ISRU mining brines. Our goal is to combine all such technologies.

  7. A review of theories on the origins of saline waters and brines in the Canadian Precambrian Shield

    International Nuclear Information System (INIS)

    Bottomley, D.J.

    1996-02-01

    Groundwater at depths greater that 500 m in the Canadian Precambrian Shield is typically saline with a sodium-calcium/chloride chemical composition. Brines with dissolved solid concentrations exceeding 100 g/L have been encountered in several deep mines (>1000 m) on the Shield. Theories on the origins of these deep saline waters and brines can be grouped into two general categories: (1) autochthonous (in situ) origins attributable to silicate mineral hydrolysis over geologic time scales, leaching of fluid inclusions or radiolysis effects, and (2) allochthonous (external) sources caused by the infiltration of brine of modified seawater origins in the geologic past. Although the chemical and isotopic compositions of these waters clearly reflect the effects of reaction between the water and their silicate host rocks, it is unlikely that the high chlorinity of the brines is in an autochthonous attribute. It is proposed that the compositions of these brines are most compatible with the Paleozoic residual brine hypothesis of Spencer (1987). This theory invokes deep infiltration of a high-density residual brine, formed by the evaporation of seawater during Devonian time, into underlying Precambrian basement rocks where subsequent chemical modifications occurred. (author) 39 refs., 2 figs

  8. Evidence that the terms of petroleum contracts influence the rate of development of oil fields

    International Nuclear Information System (INIS)

    Mahmud, M.B.; Russell, A.

    2002-01-01

    This paper presents evidence that the main determinant of the rate of development of Libya's crude oil upstream activities, from 1961 to 1999, was the terms of the petroleum contractual agreements, which existed between the state and the international oil industry during that period, and that US sanctions against the Socialist People's Libyan Arab Jamahiriya failed to affect this rate of development. In keeping with other Members of the Organisation of the Petroleum Exporting Countries (OPEC), Libya has, over three decades, been a key player in helping to regulate global production levels of oil and gas. However, the economic and political strengths and weaknesses of individual Members of OPEC vary widely and it is inevitable that the stresses arising from adherence to OPEC policies will vary proportionately to these strengths and weaknesses. It is instructive, therefore, to analyse how successfully Libya has exploited its own petroleum resources. The results are thought-provoking and send signals to the superpowers of the futility of economic sanctions against countries whose political policies they find distasteful. Further, the analysis highlights the need for OPEC Members to be fully informed of the significance of the terms of the petroleum agreements they employ in their countries. (author)

  9. Documentation of the petroleum market model (PMM). Appendix: Model developer's report

    International Nuclear Information System (INIS)

    1994-01-01

    The Office of Integrated Analysis and Forecasting (OIAF) is required to provide complete model documentation to meet the EIA Model Acceptance Standards. The EIA Model Documentation: Petroleum Market Model of the National Energy Modeling System provides a complete description of the Petroleum Market Model's (PMM) methodology, and relation to other modules in the National Energy Modeling System (NEMS). This Model Developer's Report (MDR) serves as an appendix to the methodology documentation and provides an assessment of the sensitivity of PMM results to changes in input data. The MDR analysis for PMM is performed by varying several sets of input variables one-at-a-time and examining the effect on a set of selected output variables. The analysis is based on stand-alone, rather than integrated, National Energy Modeling System (NEMS) runs. This means that other NEMS modules are not responding to PMM outputs. The PMM models petroleum refining and marketing. The purpose of the PMM is to project petroleum product prices, refining activities, and movements of petroleum into the United States and among domestic regions. In addition, the PMM estimates capacity expansion and fuel consumption in, the refining industry. The PMM is also used to analyze a wide variety of petroleum-related issues and policies, in order to foster better understanding of the petroleum refining and marketing industry and the effects of certain policies and regulations. The PMM simulates the operation of petroleum refineries in the United States, including the supply and transportation of crude oil to refineries, the regional processing of these raw materials into petroleum products, and the distribution of petroleum products to meet regional demands. The essential outputs of this model are product prices, a petroleum supply/demand balance, demands for refinery fuel use, and capacity expansion

  10. Salton Sea Geothermal Field, California, as a near-field natural analog of a radioactive waste repository in salt

    Science.gov (United States)

    Elders, W. A.; Cohen, L. H.

    1983-11-01

    Since high concentrations of radionuclides and high temperatures are not normally encountered in salt domes or beds, finding an exact geologic analog of expected near-field conditions in a mined nuclear waste repository in salt will be difficult. The Salton Sea Geothermal Field, however, provides an opportunity to investigate the migration and retardation of naturally occurring U, Th, Ra, Cs, Sr and other elements in hot brines which have been moving through clay-rich sedimentary rocks for up to 100,000 years. The more than thirty deep wells drilled in this field to produce steam for electrical generation penetrate sedimentary rocks containing concentrated brines where temperatures reach 3650C at only 2 km depth. The brines are primarily Na, K, Ca chlorides with up to 25% of total dissolved solids; they also contain high conentrations of metals such as Fe, Mn, Li, Zn, and Pb. This report describes the geology, geophysics and geochemistry of this system as a prelude to a study of the mobility of naturally occurring radionuclides and radionuclide analogs within it.

  11. Petroleum and natural gas economy in Arab Countries and in Benin, Chad Cameroon, Namibia, Nigeria

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    This paper gives informations on petroleum and natural gas industry, petroleum market and prices, trade and contracts, prospection and production. In Saudi Arabia, Saudi Aramco has begun the works to increase the production capacity of the petroleum refinery of Ras Tanura. In Kuwait, the cost of the retrofitting and development programs for the petroleum field is evaluated to 4 milliards $. Several contracts have been signed in Tunisia and in Nigeria for the attribution of exploration permits. A cooperation agreement has been signed, in Taiwan, between Total and Chinese Petroleum Corporation, which allows the establishment of joint ventures for the development of petroleum exploration in Far East. Petroleum exploration has begun in Namibia where Norsk Hydro has achieved the interpretation of seismic studies and will drill a first exploration well. In Egypt, petroleum production is stabilized at a level of 870000 barrels per day and the transport capacity of Sumed pipeline will increase from 80 to 117 millions tons per year in 1994

  12. Attraction aspects of petroleum industry: fragilities and opportunities for the petroleum companies - part 2; Atratividade da industria para-petrolifera: fragilidades e oportunidades para as petroleiras - parte 2

    Energy Technology Data Exchange (ETDEWEB)

    Duque, Marcelo Ascher; Szklo, Alexandre [Universidade Federal do Rio de Janeiro (PPE/COPPE/UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-Graduacao de Engenharia. Programa de Planejamento Energetico

    2010-07-01

    This paper is the second part of the study that examine the structure of the para-petroleum worldwide industry, in accordance with strategies of the largest service industries, the merger and the acquisitions, and the positioning of petroleum of petroleum related to their suppliers. The trajectory of the petroleum price since the beginning of the present decade and the investment volume of the petroleum companies on projects of E and P substantially increased the cash flow of their goods and services suppliers. So, as an answer, the recent mergers and acquisitions or the great companies of the service sector are modifying the grade of concentration of various activities alongside of the productive chain. This paper tests the statistical relationship among the the petroleum price and the invoicing of five largest worldwide petroleum companies, revealing the impact of the variation of petroleum price can have on the attraction of the service sector and their unfolding on the costs of the E and P projects.

  13. European Community in new international petroleum order

    International Nuclear Information System (INIS)

    Finon, D.

    1992-01-01

    This paper examines the chances that the European Community (EC) has of enhancing its position in the international petroleum order. Its identity should become stronger than it is in the current feeble state of Europe as a world presence for four reasons: greater convergence in the ideas and interests of the Member Countries; the bolstering of Community institutions; thanks to new treaties, more balanced petro-political relations; and the geographical advantage of being within reach of Russia's enormous hydrocarbon resources. In its producer-consumer relations, the EC has a certain amount of upfront legitimacy over the actions of the individual member countries, insofar as multilateral actions in this field are more efficient than are bilateral relations. The EC is acquiring a certain autonomy of action from the AIH. It is already helping to build up new relations through informal dialogue and free-trade agreements with the producing countries, and is helping Russia to emerge as a major competitor for the Gulf countries

  14. Facts 2000. The Norwegian Petroleum Sector

    International Nuclear Information System (INIS)

    2000-02-01

    Petroleum production on the Norwegian continental shelf (NCS) in the North Sea, the Norwegian Sea and the Barents Sea totalled 2.7 bn scm oil equivalents (oe) up to 1998. Per December 1999, remaining reserves totalled 1.5 bn scm of oil, 1.2 bn scm oe gas and 0.2 bn scm oe of NGL/condensate. Twenty-eight exploration wells were completed or temporarily abandoned on the NCS in 1999. By 31 December 1999, 967 exploration wells had been completed or temporarily abandoned off Norway. Discoveries totalled 45-60 mill scm of oil and 45-70 bn scm of gas. Governmental approval was given in 1999 for the Tune, Borg and Sygna developments. Investment in exploration, field development and pipeline transport totalled about NOK 67 bn in 1998. Oil and gas production in 1999 was roughly on the par with 1998, while NGL/condensate sales rose by 19 per cent. The Balder, Gullfaks South, Jotun, Oseberg East, Visund and Aasgard projects came on stream during 1999. It is estimated that, with the present production rate, Norway's remaining discovered oil resources will last for 17 years, and gas, 93 years. The estimated value of Norwegian petroleum export in 1999 was NOK 168 bn, which is about 36% of the country's total earnings from foreign sales. Published by the Norwegian Ministry of Petroleum and Energy, the book is a major source of information on the Norwegian offshore petroleum activities

  15. Facts 2000. The Norwegian Petroleum Sector

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-02-01

    Petroleum production on the Norwegian continental shelf (NCS) in the North Sea, the Norwegian Sea and the Barents Sea totalled 2.7 bn scm oil equivalents (oe) up to 1998. Per December 1999, remaining reserves totalled 1.5 bn scm of oil, 1.2 bn scm oe gas and 0.2 bn scm oe of NGL/condensate. Twenty-eight exploration wells were completed or temporarily abandoned on the NCS in 1999. By 31 December 1999, 967 exploration wells had been completed or temporarily abandoned off Norway. Discoveries totalled 45-60 mill scm of oil and 45-70 bn scm of gas. Governmental approval was given in 1999 for the Tune, Borg and Sygna developments. Investment in exploration, field development and pipeline transport totalled about NOK 67 bn in 1998. Oil and gas production in 1999 was roughly on the par with 1998, while NGL/condensate sales rose by 19 per cent. The Balder, Gullfaks South, Jotun, Oseberg East, Visund and Aasgard projects came on stream during 1999. It is estimated that, with the present production rate, Norway's remaining discovered oil resources will last for 17 years, and gas, 93 years. The estimated value of Norwegian petroleum export in 1999 was NOK 168 bn, which is about 36% of the country's total earnings from foreign sales. Published by the Norwegian Ministry of Petroleum and Energy, the book is a major source of information on the Norwegian offshore petroleum activities.

  16. Facts 2000. The Norwegian Petroleum Sector

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-02-01

    Petroleum production on the Norwegian continental shelf (NCS) in the North Sea, the Norwegian Sea and the Barents Sea totalled 2.7 bn scm oil equivalents (oe) up to 1998. Per December 1999, remaining reserves totalled 1.5 bn scm of oil, 1.2 bn scm oe gas and 0.2 bn scm oe of NGL/condensate. Twenty-eight exploration wells were completed or temporarily abandoned on the NCS in 1999. By 31 December 1999, 967 exploration wells had been completed or temporarily abandoned off Norway. Discoveries totalled 45-60 mill scm of oil and 45-70 bn scm of gas. Governmental approval was given in 1999 for the Tune, Borg and Sygna developments. Investment in exploration, field development and pipeline transport totalled about NOK 67 bn in 1998. Oil and gas production in 1999 was roughly on the par with 1998, while NGL/condensate sales rose by 19 per cent. The Balder, Gullfaks South, Jotun, Oseberg East, Visund and Aasgard projects came on stream during 1999. It is estimated that, with the present production rate, Norway's remaining discovered oil resources will last for 17 years, and gas, 93 years. The estimated value of Norwegian petroleum export in 1999 was NOK 168 bn, which is about 36% of the country's total earnings from foreign sales. Published by the Norwegian Ministry of Petroleum and Energy, the book is a major source of information on the Norwegian offshore petroleum activities.

  17. Meltability and Stretchability of White Brined Cheese: Effect of Emulsifier Salts

    OpenAIRE

    Khaled Abu-Alruz; Ayman S. Mazahreh; Ali F. Al-Shawabkeh; Amer A. Omari; Jihad M. Quasem

    2009-01-01

    Problem statement: This study was based on the hypothesis that by adding low concentrations of emulsifier salts, may specifically act on the cross linking bonds of the protein matrix, to the original brine (storage medium) it would be possible to induce meltability and stretchability in white brined cheese. Approach: A new apparatus for measuring the actual stretchability was designed and constructed; measurements on different cheese samples proved its validity and reliability to measure stre...

  18. Uranium, RADON and radon isotopes in selected brines of Poland

    International Nuclear Information System (INIS)

    Kozlowska, B.; Walencik, A.; Zipper, W.; Dorda, J.; Przylibski, T.A.

    2010-01-01

    Natural radioactive isotopes were studied in nine different types of brines from four locations in Poland. Investigated brines are exploited from various geological structures composed of the rocks of different chemical and mineral composition as well as different age and depth. All investigated brines are used in balneotherapy (i.e. baths, inhalations, showers). The main goal of this study was to obtain some basic knowledge on the activity range of natural elements such as uranium, RADON and radon in different brine types in Poland and their variability depending on their location in certain geological structures. Activities of 234,238 U, 226,228 Ra and 222 Rn isotopes were measured with the use of two nuclear spectrometry techniques: liquid scintillation and alpha spectrometry. The activity concentrations of 222 Rn vary from below 1 to 76.1±3.7 Bq/l, for the 226 Ra isotope from 0.19±0.01 to 85.5±0.4 Bq/l and for 228 Ra from below 0.03 to 2.17±0.09 Bq/l. For uranium isotopes, the concentrations are in the range from below 0.5 to 5.1±0.4 mBq/l for 238 U and from 1.6±0.4 to 45.6±2.0 mBq/l for 2 34U . The obtained results indicate high RADON activity concentrations corresponding to high mineralization of waters. (authors)

  19. Fate of Magnesium Chloride Brine Applied to Suppress Dust from Unpaved Roads at the INEEL Subsurface Disposal Area

    International Nuclear Information System (INIS)

    Larry Hull; Carolyn Bishop

    2004-01-01

    Between 1984 and 1993, MgCl 2 brine was used to suppress dust on unpaved roads at a radioactive waste subsurface disposal area. Because Cl - might enhance corrosion of buried metals in the waste, we investigated the distribution and fate of Cl - in the vadose zone using pore water samples collected from suction lysimeters and soluble salt concentrations extracted from sediment samples. The Cl/Br mass ratio and the total dissolved Cl - concentration of pore water show that brine contamination occurs primarily within 13 m of treated roads, but can extend as much as 30 m laterally in near-surface sedimentary deposits. Within the deep vadose zone, which consists of interlayered basalt lava flows and sedimentary interbeds, brine has moved up to 110 m laterally. This lateral migration suggests formation of perched water and horizontal transport during periods of high recharge. In a few locations, brine migrated to depths of 67 m within 3 to 5 yr. Elevated Cl - concentrations were found to depths of 2 m in roadbed material. In drainage ditches along roads, where runoff accumulates and recharge of surface water is high, Cl - was flushed from the sediments in 3 to 4 yr. In areas of lower recharge, Cl - remained in the sediments after 5 yr. Vertical brine movement is directly related to surface recharge through sediments. The distribution of Cl - in pore water and sediments is consistent with estimates of vadose zone residence times and spatial distribution of surface water recharge from other investigations at the subsurface disposal area

  20. Petroleum and Health Care: Evaluating and Managing Health Care's Vulnerability to Petroleum Supply Shifts

    Science.gov (United States)

    Bednarz, Daniel; Bae, Jaeyong; Pierce, Jessica

    2011-01-01

    Petroleum is used widely in health care—primarily as a transport fuel and feedstock for pharmaceuticals, plastics, and medical supplies—and few substitutes for it are available. This dependence theoretically makes health care vulnerable to petroleum supply shifts, but this vulnerability has not been empirically assessed. We quantify key aspects of petroleum use in health care and explore historical associations between petroleum supply shocks and health care prices. These analyses confirm that petroleum products are intrinsic to modern health care and that petroleum supply shifts can affect health care prices. In anticipation of future supply contractions lasting longer than previous shifts and potentially disrupting health care delivery, we propose an adaptive management approach and outline its application to the example of emergency medical services. PMID:21778473

  1. Bacterial Utilization of Petroleum in Liquid and Simulated Soil ...

    African Journals Online (AJOL)

    ... by the weight of extracted residual oil indicated that the extents of oil removal in the stimulated and/or bioaugmented soils were significantly high in relation to unsupplemented and uninoculated controls. Keywords: Bacterial utilization, Petroleum in liquid, Petroleum in soil, Environments Bio-Research Vol. 6 (2) 2008: pp.

  2. Petroleum and natural gas economy in Arab countries and in Angola, Gabon, Iran, Nigeria

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    This paper gives informations about petroleum and natural gas industry, petroleum market and prices, trade and contracts, prospection and production. In Saudi Arabia, the debate about the price reduction of butane used to produce methyl tertiary butyl ether (MTBE) is responsible of the cancellation of joint venture project between Mobil and Arabian Chemical Investment Corp. In Algeria, Japan brings its support to the development of Liquefied Petroleum Gases industry and has signed two exports contracts. New petroleum discoveries have been made in Oman, near Suneinah and in Egypt near Belayim offshore oil field. Petroleum production has reached 3.6 millions barrels per day in Iran, 0.35 millions barrels per day in Gabon and 0.177 millions barrels per day in Nigeria

  3. Petroleum and ethics

    International Nuclear Information System (INIS)

    Henn, N.; Train, E.; Chagnoux, H.; Heinzle, P.; Daubresse, M.; Bret-Rouzaut, N.; Fradin, J.

    2000-01-01

    7 articles in this data sheet, they concern: political stakes and stakes of the industrial petroleum sector towards ethical questions; establishment of associations attending to human and environmental questions; examples of of ethical, environmental and safety policy in an industrialized country (ExxonMobil) and in a developing country (TotalFina); synthesis of the ethical problems that the petroleum industry encounter in industrialized and developing countries; considerations on the communication stakes in petroleum companies with the general public. (O.M.)

  4. Petroleum marketing monthly, May 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-05-26

    The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

  5. Brine shrimp lethality and antibacterial activity of extracts from the bark of Schleichera oleosa

    Directory of Open Access Journals (Sweden)

    Laxman Pokhrel

    2015-08-01

    Full Text Available Objective: To determine the antibacterial efficacy and brine shrimp toxicity of extracts (hexane, dichloromethane, ethyl acetate, methanol and water obtained from the bark of Schleichera oleosa. Methods: The powdered bark sample was Soxhlet extracted sequentially in hexanes, dichloromethane, ethyl acetate, methanol and water. Antibacterial evaluation was carried out by following the agar diffusion method and amoxicillin disc was used as a reference. Slightly modified Meyer’s method was used to determine the toxicity of the extracts in brine shrimps. Results: Among the nine bacterial strains tested, the methanolic and aqueous extracts showed promising antibacterial efficacy against Serratia marcescens, Escherarichia coli, Bacillus subtilis and Micrococcus luteus. None of the extracts were found significantly toxic to brine shrimps. Conclusions: Strong antibacterial activity and low brine shrimp toxicity of methanolic and aqueous extracts can provide new antibacterial compounds.

  6. Socio-economic benefits from petroleum industry activity in Newfoundland and Labrador 2003 and 2004

    International Nuclear Information System (INIS)

    2005-11-01

    An update on previous macroeconomic analyses of the impacts of offshore petroleum activities in Newfoundland and Labrador was presented. Details of industry activity and expenditures in Newfoundland and Labrador were presented as well as the resultant direct, indirect and induced economic benefits to the province. Related developments in infrastructure, education, training, and research and development were also provided. It was observed that there was a further consolidation and expansion of the offshore petroleum industry in the province as well as additional growth in its contribution to the province's economy. By 2004, the petroleum industry was responsible for nearly 25 per cent of the province's GDP, with total labour income being 12 per cent higher than it would have been without offshore petroleum industry activity. Significant positive effects were noted in retail sales, the unemployment rate, housing starts and the size of the provincial population. Production activity has become increasingly important, and there has been increased involvement of local companies and individuals in export work, indicating that the petroleum industry is making an important contribution to economic diversification and sustainability. New offshore petroleum activities included the Hebron oilfield project; satellite field developments in the Jeanne d'Arc Basin; exploration in the Orphan Basin and Laurentian Sub-basin; and the development of natural gas reserves using compressed natural gas (CNG) or alternative transportation strategies. Infrastructure, education, training and research and development activities were outlined. It was noted that the low level of exploration in 2003 and 2004 was a matter of concern. It was concluded that a failure to proceed with more recent development projects would be a major blow to the local petroleum industry and the economy as a whole. 2 refs., 2 tabs., 1 fig

  7. Petroleum question. Die Oelfrage

    Energy Technology Data Exchange (ETDEWEB)

    Mommer, B

    1983-01-01

    The author analyses the development of the world petroleum market and its pricing factors to the present on the basis of the theory of ground rent, in which the part played by absolute ground rent, differential rent, and free and national state property in the capitalist mode of production is determined. His investigation of economic policy traces the absorbing history of the petroleum production and policy of the United States of America, which for so long governed the world market, the development of Venezuela into a petroleum country (whose true history is here revealed for the first time), the penetration of the middle East by the international petroleum leaseholders' capital and their cartel, the formation of the OPEC, and finally the 'victory' of the lather over the petroleum combines in the international petroleum crisis of 1970-1973. The book closes with a survey at the start of the 80s and an outlook into the foreseeable future. What is really hidden behind the quarrels about prices, profit, taxes, royalties, franchise agreements, production quotas, nationalization and so forth and behind the economic, political, and even moral arguments of the parties concerned turns out to be the fight of the petroleum ground proprietors for the ground rent - but to win a victory in this fight means ultimately to face its limitations, too. Blindness to the economic and political importance of ground rent, right from the theoretical approach, also created a major cause of the false diagnoses and forecasts on the petroleum market western economic scientists were misled into, and thus of the surprise effect that came in the form of the petroleum crisis of the early 1970s.

  8. Indicators on the world petroleum markets

    International Nuclear Information System (INIS)

    2000-10-01

    This paper presents tendencies of the petroleum industry market. It analyses the petroleum demand and supply, the prices elaboration, the petroleum market and the OPEC objective, the third petroleum crisis of the year 2000 and gives some data concerning the petroleum market. (A.L.B.)

  9. Figures of the petroleum industry

    Energy Technology Data Exchange (ETDEWEB)

    1978-01-01

    The statistic tables give informations about: Reserves and production of petroleum and natural gas, supply of crude petroleum in the Federal Republic of Germany, pipelines, tanker ships, petroleum refineries, petroleum consumption, storage and distribution, automobiles, prices, taxis and energy consumption. The data compilations are primarily given for the Federal Republic of Germany.

  10. Brine flow up a borehole caused by pressure perturbation from CO2 storage: Static and dynamic evaluations

    Energy Technology Data Exchange (ETDEWEB)

    Birkholzer, J.T.; Nicot, J.-P.; Oldenburg, C.M.; Zhou, Q.; Kraemer, S.; Bandilla, K.W.

    2011-05-01

    Industrial-scale storage of CO{sub 2} in saline sedimentary basins will cause zones of elevated pressure, larger than the CO{sub 2} plume itself. If permeable conduits (e.g., leaking wells) exist between the injection reservoir and overlying shallow aquifers, brine could be pushed upwards along these conduits and mix with groundwater resources. This paper discusses the potential for such brine leakage to occur in temperature- and salinity-stratified systems. Using static mass-balance calculations as well as dynamic well flow simulations, we evaluate the minimum reservoir pressure that would generate continuous migration of brine up a leaking wellbore into a freshwater aquifer. Since the brine invading the well is denser than the initial fluid in the wellbore, continuous flow only occurs if the pressure perturbation in the reservoir is large enough to overcome the increased fluid column weight after full invasion of brine into the well. If the threshold pressure is exceeded, brine flow rates are dependent on various hydraulic (and other) properties, in particular the effective permeability of the wellbore and the magnitude of pressure increase. If brine flow occurs outside of the well casing, e.g., in a permeable fracture zone between the well cement and the formation, the fluid/solute transfer between the migrating fluid and the surrounding rock units can strongly retard brine flow. At the same time, the threshold pressure for continuous flow to occur decreases compared to a case with no fluid/solute transfer.

  11. A theoretical model of subsidence caused by petroleum production: Big Hill Field, Jefferson County, Texas

    International Nuclear Information System (INIS)

    Hill, D.W.; Sharp, J.M. Jr.

    1993-01-01

    In the Texas Gulf Coastal Plain, there is a history of oil and gas production extending over 2 to 5 decades. Concurrent with this production history, there has been unprecedented population growth accompanied by vastly increased groundwater demands. Land subsidence on both local and regional bases in this geologic province has been measured and predicted in several studies. The vast majority of these studies have addressed the problem from the standpoint of groundwater usage while only a few have considered the effects of oil and gas production. Based upon field-based computational techniques (Helm, 1984), a model has been developed to predict land subsidence caused by oil and gas production. This method is applied to the Big Hill Field in Jefferson County, Texas. Inputs include production data from a series of wells in this field and lithologic data from electric logs of these same wells. Outputs include predicted amounts of subsidence, the time frame of subsidence, and sensitivity analyses of compressibility and hydraulic conductivity estimates. Depending upon estimated compressibility, subsidence, to date, is predicted to be as high as 20 cm. Similarly, depending upon estimated vertical hydraulic conductivity, the time frame may be decades for this subsidence. These same methods can be applied to other oil/gas fields with established production histories as well as new fields when production scenarios are assumed. Where subsidence has been carefully measured above petroleum reservoir, the model may be used inversely to calculate sediment compressibilities

  12. Environment and petroleum exploration in Madagascar

    International Nuclear Information System (INIS)

    Ratsimandresy, R.; Raveloson, E.A.; Lalaharisaina, J.V.

    1991-01-01

    This paper deals with the environmental problems related to Petroleum Exploration Programs (PEP) in Madagascar and measures taken, in short terms, to minimize environment degradation resulting from these. PEP concerns the three main western sedimentary basins (Ambilobe Basin - Majunga Basin - Morodava basin) of which 12% of the surface are classified as protected area (forests, parks, reserves) in respect of the richness and rareness of wildlife species. PEP's operations (seismic survey and drilling wells), when conducted in these zones, affect the system (access road, people migration), leading to the degradation of the wildlife. For petroleum companies working in those zones, some appropriate measures (adequacy of equipment, engagement to restore damages, environment study) were required before concerned administration could grant the agreement. One example of specific environment damages caused by Petroleum Exploration Operations is mentioned in this paper

  13. 76 FR 16728 - Announcement of the American Petroleum Institute's Standards Activities

    Science.gov (United States)

    2011-03-25

    ... (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method... by Pressure Hydrometer, 3rd Ed. MPMS Chapter 9.3, Standard Test Method for Density, Relative Density...

  14. Quarterly brine migration data report, May-September 1983: Nuclear Waste Repository simulation experiments (brine migration), Asse Mine of the Federal Republic of Germany

    International Nuclear Information System (INIS)

    Coyle, A.J.; Kalia, H.N.; Eckert, J.L.

    1987-04-01

    The first quarterly brine migration data report describes experiments simulating a nuclear waste repository at the 800-m (2624-ft) level of the Asse Salt Mine in the Federal Republic of Germany from May 1983 through September 1983. This report describes the test equipment, the Asse Salt Mine, and the pretest properties of the salt in the test gallery. This report also includes test data for the first 4 months of operations on brine migration rates, borehole pressure, salt temperatures, and thermomechanical behavior of the salt. The duration of the experiments will be approximately 2 years, ending in December 1985. 83 figs., 55 tabs

  15. Geopolitics of petroleum

    International Nuclear Information System (INIS)

    Sebille-Lopez, Ph.

    2006-01-01

    The unexpected rise of oil prices since 2004 reveals some structural weaknesses of oil markets in front of the evolution of demand. It conceals considerable stakes, more political than strategic, like the securing of oil and petroleum product supplies of big consumers like the USA and China. This demand generates deep changes in the relations between the different actors, from Venezuela to Russia, from the Caspian sea to the Arab-Persian gulf, from the Mediterranean sea to the gulf of Guinea. Terrorists, who try to destabilize markets using threats on petroleum infrastructures, add-up a risk dimension to the uncertainties. The author proposes a world tour of the main production areas, along the 'oil roads' where the main strategic manoeuvres take place. He shades light on the main power stakes: pressure, tensions, threats and deals, alliances, ruptures and potential conflicts. The complex and multiple motivations are explained. (J.S.)

  16. Petroleum marketing monthly, August 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-08-15

    The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum products sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product Sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

  17. Petroleum marketing monthly, September 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-09-01

    The Petroleum Marketing Monthly (PMM) provides information and statistical data on a variety of crude oils and refined petroleum products. The publication presents statistics on crude oil costs and refined petroleum product sales for use by industry, government, private sector analysts, educational institutions, and consumers. Data on crude oil include the domestic first purchase price, the f.o.b. and landed cost of imported crude oil, and the refiners` acquisition cost of crude oil. Refined petroleum product sales data include motor gasoline, distillates, residuals, aviation fuels, kerosene, and propane. The Petroleum Marketing Division, Office of Oil and Gas, Energy Information Administration ensures the accuracy, quality, and confidentiality of the published data in the Petroleum Marketing Monthly.

  18. Noise and vibration levels in artificial polar bear dens as related to selected petroleum exploration and developmental activities

    International Nuclear Information System (INIS)

    Blix, A.S.; Lentfer, J.W.

    1992-01-01

    Petroleum exploration and development are occurring in various locations in the Arctic, where there are important denning sites for polar bears. Petroleum activities usually coincide with winter denning activities by bears, who may abandon dens if subject to prolonged annoyance. A study was carried out to measure noise and vibration levels in artificial polar bear dens at Prudhoe's Bar, Alaska, resulting from seismic testing, drilling and transport. A microphone and an accelerometer were frozen to the floor of the dens, with leads passed through a consolidated snow filled entrance to a truck, tent or helicopter. Tests were carried out on land, sea ice, and next to a drilling tower on an artificial island, which was also used to measure noise levels resulting from a helicopter taking off. It was concluded that the dry and wind-beaten arctic snow muffles both sound and vibration extremely well, and it is unlikely that polar bears in their dens will be disturbed by the type of petroleum-related activities measured, provided they do not take place within 100 m of the dens. 8 refs., 7 figs., 1 tab

  19. Experimental evaporation of hyperacid brines: Effects on chemical composition and chlorine isotope fractionation

    Science.gov (United States)

    Rodríguez, Alejandro; van Bergen, Manfred J.; Eggenkamp, H. G. M.

    2018-02-01

    Hyperacid brines from active volcanic lakes are some of the chemically most complex aqueous solutions on Earth. Their compositions provide valuable insights into processes of elemental transfer from a magma body to the surface and interactions with solid rocks and the atmosphere. This paper describes changes in chemical and δ37Cl signatures observed in a 1750 h isothermal evaporation experiment on hyperacid (pH 0.1) sulphate-chloride brine water from the active lake of Kawah Ijen volcano (Indonesia). Although gypsum was the only evaporite mineral identified in the evolving brine, decreasing Si concentrations may ultimately result in amorphous silica precipitation. Geochemical simulations predict the additional formation of elemental sulphur at lower water activities (aH2O ≤ 0.65) that were not reached in the experiment. Absence of other sulphates and halides despite the high load of dissolved elements (initial TDS ca. 100 g/kg) can be attributed to increased solubility of metals, promoted by extensive formation of complexes between the variety of cations and the major anions (HSO4-, Cl-, F-) present. Chlorine deviations from a conservative behaviour point to losses of gaseous hydrogen chloride (HCl(g)) and consequently an increase in Br/Cl ratios. Chlorine isotope fractionation that accompanied the escape of HCl(g) showed a marked change in sign and magnitude in the course of progressive evaporation of the brine. The calculated factor of fractionation between HCl(g) and dissolved Cl for the initial interval (before 500 h) is positive (1000lnαHCl(g)-Cldiss. = + 1.55 ± 0.49‰to + 3.37 ± 1.11‰), indicating that, at first, the escaping HCl(g) was isotopically heavier than the dissolved Cl remaining in the brine. Conversely, fractionation shifted to the opposite direction in the subsequent interval (1000lnαHCl(g)-Cldiss. = 5.67 ± 0.17‰to - 5.64 ± 0.08‰), in agreement with values reported in literature. It is proposed that Cl isotopic fractionation in

  20. Markov random fields simulation: an introduction to the stochastic modelling of petroleum reservoirs; Simulacao de campos aleatorios markovianos: uma introducao voltada a modelagem estocastica de reservatorios de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Saldanha Filho, Paulo Carlos

    1998-02-01

    Stochastic simulation has been employed in petroleum reservoir characterization as a modeling tool able to reconcile information from several different sources. It has the ability to preserve the variability of the modeled phenomena and permits transference of geological knowledge to numerical models of flux, whose predictions on reservoir constitute the main basis for reservoir management decisions. Several stochastic models have been used and/or suggested, depending on the nature of the phenomena to be described. Markov Random Fields (MRFs) appear as an alternative for the modeling of discrete variables, mainly reservoirs with mosaic architecture of facies. In this dissertation, the reader is introduced to the stochastic modeling by MRFs in a generic sense. The main aspects of the technique are reviewed. MRF Conceptual Background is described: its characterization through the Markovian property and the equivalence to Gibbs distributions. The framework for generic modeling of MRFs is described. The classical models of Ising and Potts-Strauss are specific in this context and are related to models of Ising and Potts-Strauss are specific in this context and are related to models used in petroleum reservoir characterization. The problem of parameter estimation is discussed. The maximum pseudolikelihood estimators for some models are presented. Estimators for two models useful for reservoir characterization are developed, and represent a new contribution to the subject. Five algorithms for the Conditional Simulation of MRFs are described: the Metropolis algorithm, the algorithm of German and German (Gibbs sampler), the algorithm of Swendsen-Wang, the algorithm of Wolff, and the algorithm of Flinn. Finally, examples of simulation for some of the models discussed are presented, along with their implications on the modelling of petroleum reservoirs. (author)

  1. Yugoslavian Petroleum Refinery development program

    International Nuclear Information System (INIS)

    Ocic, Ozren

    1999-01-01

    This paper shows the analysis of the world petroleum industry development, being an important factor in planning the development of the Yugoslav petroleum industry and Pancevo Petroleum Refinery, as well. Then Yugoslav petroleum industry development is analysed, including the appropriate balances of crude oil production and crude oil products consumption. The way of realizing the basic targets are also proposed. Likewise, the analysis of the condition within West European refineries has been conducted, from the aspects of technology, energy consumption and environmental protection and the same analysis for Pancevo Petroleum Refinery has been presented, too. The analysis of the condition within the refineries in the European Union countries and comparing it with the condition within Pancevo Petroleum Refinery, makes it mainly possible to recognize the development programmes which should be realized in order that Pancevo Petroleum Refinery could reach the refining level of the EU countries. (Original)

  2. Recovery of biomolecules from marinated herring (Clupea harengus) brine using ultrafiltration through ceramic membranes

    DEFF Research Database (Denmark)

    Gringer, Nina; Hosseini, Seyed Vali; Svendsen, Tore

    2015-01-01

    Marinated herring processing brines, which are usually discarded, are rich in salt, protein, non-protein nitrogen, iron, fatty acids, antioxidant and even possess enzymatic activity. This study investigated the performance of ceramic ultrafiltration of two herring spice brines with a major focus...

  3. Petroleum refining and air quality

    International Nuclear Information System (INIS)

    Raimbault, C.

    1992-01-01

    This paper studies the methods which may be developed in petroleum refineries or during petroleum products using for air pollution abatement: petroleum products desulfurization, lead elimination in gasoline and catalytic converters to reduce sulfur dioxide and nitrogen oxides in exhaust gases. Investments and costs estimation to adapt petroleum refineries for environment protection is also given. 1 ref., 6 figs., 6 tabs

  4. 2005 yearly days of petroleum

    International Nuclear Information System (INIS)

    Constant, R.; Susbielles, G.

    2005-01-01

    14 articles are gathered in this data sheet; they deal with the opening address of the 2005 petroleum days; the hydrocarbons: the evolutive resource; the para-petroleum engineers and the Europe; the speech of Mr Francois Loos; the Shell global scenarios to 2025; the evolution of the gas resource and its uses; the French para-petroleum industry; Bernard Bensaid, Corinne Sagary, Armelle Saniere, economic studies, IFP; the contribution of the innovation and of the technology in the diversification of the hydrocarbons supply; innovation and diversification of the petroleum resource: the point of view of Total; research, development and diversification of the petroleum resource; innovation in services companies; innovation in study and development and engineering; the closing address of the 2005 petroleum days. (O.M.)

  5. Design calculations for a combined ventilation and brine injection experiment at the Grimsel Rock Laboratory, Switzerland

    International Nuclear Information System (INIS)

    Finsterle, S.; Pruess, K.

    1993-07-01

    A combined ventilation and brine injection test is planned at the Grimsel Test Site. The objective of the experiment is to study the transport of liquid and gas in the vicinity of a ventilated drift in order to evaluate the impact of the drying process on the characterization of the rock matrix. The proposed test sequence includes a desaturation-resaturation cycle. In addition, brine and fresh water will be injected from a borehole as trace electrolytes in order to better track the propagation of the individual phases. Results of design calculations using the TOUGH2 code show that injection of brine may significantly influence the unsaturated flow behavior by changing the pressure and saturation distribution around the borehole. Transport velocity is predicted to be very slow, requiring several months for the brine to reach the draft wall. However, the presence of preferential flow paths may reduce travel time and alter brine content and saturation distribution so that certain sensors may respond earlier or not at all

  6. Slumping of brine mounds : bounds on behaviour

    NARCIS (Netherlands)

    Philips, J.R.; Duijn, van C.J.

    1996-01-01

    Two modifications of the approximate analysis of interface motion during two-fluid density-driven flows of De Josselin de Jong (Proc. Euromech., 143: 75–82, 1981) are applied to the slumping of finite two-dimensional and axisymmetric brine mounds. Both lead to simple similarity solutions. One

  7. Fermentation cover brine reformulation for cucumber processing with low salt to reduce bloater defect

    Science.gov (United States)

    Reformulation of calcium chloride cover brine for cucumber fermentation was explored as a mean to minimize the incidence of bloater defect. This study particularly focused on cover brine supplementation with calcium hydroxide, sodium chloride (NaCl), and acids to enhance buffer capacity, inhibit the...

  8. A comparative evaluation of nitrogen compounds in petroleum distillates

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Dheer; Chopra, Anju; Patel, Mitra Bhanu; Sarpal, Amarjit Singh [Indian Oil Corporation Limited, Faridabad (India). Research and Development Centre

    2011-07-15

    Although the concentration of nitrogen compounds in crude oil is relatively low, they can become more concentrated in petroleum distillates and poison the catalysts used in refining processes. They cause undesirable deposits, color formation and odor in products; they also contribute to air pollution and some are highly carcinogenic. The poisoned catalyst becomes deactivated for hydrodesulfurization and unable to remove sulfur from middle distillates. In order to understand the effect on catalytic processes, it is desirable to identify the nitrogen compounds in various petroleum distillates. This paper compares the nitrogen species profiles in different petroleum distillates using a nitrogen chemiluminescence detector. In addition, four different petroleum distillate samples from different refineries were analyzed to find the variation in their nitrogen profiles. The nitrogen compounds in petroleum distillate samples were identified as anilines, quinolines, indoles, and carbazoles and their alkyl derivatives. Quantitation was carried out against known reference standards. The quantitative data were compared to the total nitrogen content determined by elemental analysis. (orig.)

  9. Recovery of Lithium from Geothermal Brine with Lithium-Aluminum Layered Double Hydroxide Chloride Sorbents.

    Science.gov (United States)

    Paranthaman, Mariappan Parans; Li, Ling; Luo, Jiaqi; Hoke, Thomas; Ucar, Huseyin; Moyer, Bruce A; Harrison, Stephen

    2017-11-21

    We report a three-stage bench-scale column extraction process to selectively extract lithium chloride from geothermal brine. The goal of this research is to develop materials and processing technologies to improve the economics of lithium extraction and production from naturally occurring geothermal and other brines for energy storage applications. A novel sorbent, lithium aluminum layered double hydroxide chloride (LDH), is synthesized and characterized with X-ray powder diffraction, scanning electron microscopy, inductively coupled plasma optical emission spectrometry (ICP-OES), and thermogravimetric analysis. Each cycle of the column extraction process consists of three steps: (1) loading the sorbent with lithium chloride from brine; (2) intermediate washing to remove unwanted ions; (3) final washing for unloading the lithium chloride ions. Our experimental analysis of eluate vs feed concentrations of Li and competing ions demonstrates that our optimized sorbents can achieve a recovery efficiency of ∼91% and possess excellent Li apparent selectivity of 47.8 compared to Na ions and 212 compared to K ions, respectively in the brine. The present work demonstrates that LDH is an effective sorbent for selective extraction of lithium from brines, thus offering the possibility of effective application of lithium salts in lithium-ion batteries leading to a fundamental shift in the lithium supply chain.

  10. Evaluation of burn injuries related to liquefied petroleum gas.

    Science.gov (United States)

    Tarim, Mehmet Akin

    2014-01-01

    Liquefied petroleum gas (LPG) is a fuel that is widely used for domestic, agricultural, and industrial purposes. LPG is also commonly used in restaurants, industries, and cars; however, the home continues to be the main site for accidents. In Turkey, the increased usage of LPG as a cooking or heating fuel has resulted in many burn injuries from LPG mishaps. Between January 2000 and June 2011, 56 LPG-burned patients were compared with 112 flame-burned patients. There were no significant differences with respect to the mean age, sex, hospitalization time, and mortality in both groups. In the LPG-caused burn cases, 41 burns (73.2%) occurred at home, seven (12.5) were work-related mishaps, and eight (14.3) were associated with car accidents. The majority of the LPG burns (82%, 46 patients) resulted from a gas leak, and 18% of them were related to the failure to close LPG tubes in the patients' kitchens (10 patients). Burns to the face and neck (82 vs 67%, P = .039) and upper (62 vs 23%, P = .000) and lower (70 vs 45%, P = .002) extremities were significantly higher in LPG-caused burn cases than flame-burned cases. General awareness regarding the risk of LPG and first aid for burns appears to be lacking. The LPG delivery system should be standardized throughout countries that widely use LPG.

  11. Fact 2004. The Norwegian petroleum sector

    Energy Technology Data Exchange (ETDEWEB)

    Gooderham, Rolf E [ed.

    2004-07-01

    production for the year totalled 73.4 bn scm. Gas sales are expected to build up sharply from today's level to reach 120 bn scm in 2010. Development plans for Ormen Lange in the Norwegian Sea and a new gas transport system to the UK were completed by the end of 2003. Ormen Lange is the largest gas discovery on the NCS after Troll. This development and the planned transport system to the UK are very important contributions to the future activity on the NCS, and these projects will have substantial national and regional effects. Against the background of disappointing exploration results in immature areas of the Norwegian and North Seas during recent years, the government decided to announce an extensive 18th licensing round in these parts of the NCS. It will give companies the access to immature acreage, which is important for increasing exploration activity. In announcing it, the government has carefully balanced the interests of the environment, the fisheries, the aquaculture and the petroleum activities. While being highly significant for future Norwegian petroleum operations, the Lofoten-Barents Sea area of the NCS is very important both ecologically and for the fishing industry. At the end of 2003, 48 fields were in production on the NCS, 42 in the North Sea and six in the Norwegian Sea. Production began in 2003 from Fram, Grane and Mikkel. Kristin, Kvitebjoern, Skirne and Snoehvit have approved plans for development and operation, but are being developed. Forecasts indicate that remaining resources on the NCS could permit profitable production of oil for 50 years and gas for almost a century. Achieving such a positive development is very demanding. Key challenges include access to new acreage to ensure the necessary exploration activity, development of resources close to existing infrastructure and improved recovery factor for producing fields. The government is concerned to facilitate the achievement of the long-term scenario. This will accordingly be the key subject

  12. Bioremediation of petroleum contaminated soil

    International Nuclear Information System (INIS)

    Autry, A.R.; Ellis, G.M.

    1992-01-01

    This paper reports on bioremediation, which offers a cost-competitive, effective remediation alternative for soil contaminated with petroleum products. These technologies involve using microorganisms to biologically degrade organic constituents in contaminated soil. All bioremediation applications must mitigate various environmental rate limiting factors so that the biodegradation rates for petroleum hydrocarbons are optimized in field-relevant situations. Traditional bioremediation applications include landfarming, bioreactors, and composting. A more recent bioremediation application that has proven successful involves excavation of contaminated soil. The process involves the placement of the soils into a powerscreen, where it is screened to remove rocks and larger debris. The screened soil is then conveyed to a ribbon blender, where it is mixed in batch with nutrient solution containing nitrogen, phosphorus, water, and surfactants. Each mixed soil batch is then placed in a curing pile, where it remains undisturbed for the remainder of the treatment process, during which time biodegradation by naturally occurring microorganisms, utilizing biochemical pathways mediated by enzymes, will occur

  13. Petroleum supply monthly, March 1994

    Energy Technology Data Exchange (ETDEWEB)

    1994-03-30

    Data presented in the Petroleum Supply Monthly (PSM) describe the supply and disposition of petroleum products in the United States and major US geographic regions. The data series describe production, imports and exports, inter-Petroleum Administration for Defense (PAD) District movements, and inventories by the primary suppliers of petroleum products in the United States (50 States and the District of Columbia). The reporting universe includes those petroleum sectors in primary supply. Included are: petroleum refiners, motor gasoline blenders, operators of natural gas processing plants and fractionators, inter-PAD transporters, importers, and major inventory holders of petroleum products and crude oil. When aggregated, the data reported by these sectors approximately represent the consumption of petroleum products in the United States. Data presented in the PSM are divided into two sections: Summary Statistics and Detailed Statistics. The tables and figures in the Summary Statistics section of the PSM present a time series of selected petroleum data on a US level. Most time series include preliminary estimates for one month based on the Weekly Petroleum Supply Reporting System; statistics based on the most recent data from the Monthly Petroleum Supply Reporting System (MPSRS); and statistics published in prior issues of the PSM and PSA. The Detailed Statistics tables of the PSM present statistics for the most current month available as well as year-to-date. In most cases, the statistics are presented for several geographic areas -- the United States (50 States and the District of Columbia), five PAD Districts, and 12 Refining Districts. At the US and PAD District level, the total volume and the daily rate of activities are presented. The statistics are developed from monthly survey forms submitted by respondents to the EIA and from data provided from other sources.

  14. Identification of petroleum pollution sources

    International Nuclear Information System (INIS)

    Begak, O.Yu.; Syroezhko, A.M.

    2001-01-01

    A possibility of preliminary identification of petroleum pollution sources was investigated on specimens of the Khanty-Mansi autonomous district six deposits and specimens of soil and water polluted by these petroleums. Investigations were conducted using IR Fourier spectroscopy and gamma spectrometry, as well as methods of chromato-mass spectrometry and capillary gas liquid chromatography. Every of studied samples of petroleum from different deposits have an individual radiation impression. Insignificant total content of radionuclides in samples is specific to the Khanty-Mansi petroleum region. Gamma spectrometry admits to identify potential source of petroleum pollution using radionuclides of uranium and thorium series [ru

  15. Microbial dynamics in petroleum oilfields and their relationship with physiological properties of petroleum oil reservoirs.

    Science.gov (United States)

    Varjani, Sunita J; Gnansounou, Edgard

    2017-12-01

    Petroleum is produced by thermal decay of buried organic material over millions of years. Petroleum oilfield ecosystems represent resource of reduced carbon which favours microbial growth. Therefore, it is obvious that many microorganisms have adapted to harsh environmental conditions of these ecosystems specifically temperature, oxygen availability and pressure. Knowledge of microorganisms present in ecosystems of petroleum oil reservoirs; their physiological and biological properties help in successful exploration of petroleum. Understanding microbiology of petroleum oilfield(s) can be used to enhance oil recovery, as microorganisms in oil reservoirs produce various metabolites viz. gases, acids, solvents, biopolymers and biosurfactants. The aim of this review is to discuss characteristics of petroleum oil reservoirs. This review also provides an updated literature on microbial ecology of these extreme ecosystems including microbial origin as well as various types of microorganisms such as methanogens; iron, nitrate and sulphate reducing bacteria, and fermentative microbes present in petroleum oilfield ecosystems. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. The world petroleum industry

    International Nuclear Information System (INIS)

    Mons, L.

    2005-01-01

    This study proposes a global vision of the petroleum industry, a precise and well argued state of the art of the petroleum markets. It defines the strategical challenges which the petroleum companies are exposed and allows to anticipate the sector evolutions. It details the key acts of the last three years, the financial performances of the companies. (A.L.B.)

  17. The reduction of petroleum hydrocarbons in soil under saline conditions using ultrasound

    Energy Technology Data Exchange (ETDEWEB)

    McMillan, D. [SNC-Lavallin, Vancouver, BC (Canada); Northern British Columbia Univ., Prince George, BC (Canada)

    2010-07-01

    Petroleum hydrocarbons (PHCs) and salts are two of the most common soil contaminants found at oil and gas extraction sites. High concentrations of salt from brine spills may amplify the challenges of soil remediation by reducing bioavailability for remediation. This PowerPoint presentation described an ultrasonic soil flushing technology that used sonic cavitation to break down contaminants. Long chain and aromatic hydrocarbons with complex structures were broken down by the direct oxidation under high temperature and pressure environments created by the sonic cavitation process. The cavitation waves broke up the aggregates of solid particles and increased the turbulence and transportation of the contaminants. A laboratory study evaluated the ability of the treatment process to remediate salt and hydrocarbon contaminated soil samples. The adsorption isotherms of the samples were analyzed. Sand, clay, and muskeg samples were treated. Results of the study suggested that the treatment is more effective when treating granular soils with high hydraulic conductivity. Even small amounts of salt were found to have a negative impact on the reduction of hydrocarbon contaminants. tabs., figs.

  18. Thermodynamic modeling of phases equilibrium in aqueous systems to recover potassium chloride from natural brines

    Directory of Open Access Journals (Sweden)

    Ruberlan Gomes da Silva

    2017-01-01

    Full Text Available Chemical fertilizers, such as potassium chloride, ammonium nitrate and other chemical products like sodium hydroxide and soda ash are produced from electrolyte solutions or brines with a high content of soluble salts. Some of these products are manufactured by fractional crystallization, when several salts are separated as solid phases with high purity (>90%. Due to the large global demand for potassium fertilizers, a good knowledge about the compositions of salts and brines is helpful to design an effective process. A thermodynamic model based on Pitzer and Harvie's model was used to predict the composition of crystallized salts after water removal by forced evaporation and cooling from multicomponent solutions or brines. Initially, the salts’ solubilities in binary systems (NaCl–H2O, KCl–H2O and MgCl2–H2O and ternary system (KCl–MgCl2–H2O were calculated at 20 °C and compared with literature data. Next, the model was compared to our experimental data on the quinary system NaCl–KCl–MgCl2–CaCl2–H2O system at 20 °C. The Pitzer and Harvie's model represented well both the binary and ternary systems. Besides, for the quinary system the fit was good for brine densities up to 1350 kg/m3. The models were used to estimate the chemical composition of the solutions and salts produced by fractional crystallization and in association with material balance to respond to issues related to the production rates in a solar pond containing several salts dissolved, for instance, NaCl, KCl, MgCl2 and CaCl2.

  19. Do we have to fear a forth petroleum crash?

    International Nuclear Information System (INIS)

    Jestin-Fleury, N.

    1998-01-01

    This paper analyses the worldwide energy scenarios for the forecasting of petroleum supply and demand in the year 2020: competition with natural gas industry, oil reserves, resources, production, development of new technologies, investments, fields development, drop of production costs, exploitation of tar sands, extra-heavy crudes, bituminous shales, reduction of the petroleum consumption in the transportation sector (development of LPG and electric powered vehicles, chemical conversion of natural gas, fuel cells), increase of the OPEC countries production, evolution of nuclear energy and economical impact of a serious fight against greenhouse gases emission and climate changes. (J.S.)

  20. Consolidation and permeability of salt in brine

    International Nuclear Information System (INIS)

    Shor, A.J.; Baes, C.F. Jr.; Canonico, C.M.

    1981-07-01

    The consolidation and loss of permeability of salt crystal aggregates, important in assessing the effects of water in salt repositories, has been studied as a function of several variables. The kinetic behavior was similar to that often observed in sintering and suggested the following expression for the time dependence of the void fraction: phi(t) = phi(0) - (A/B)ln(1 + Bt/z(0) 3 ), where A and B are rate constants and z(0) is initial average particle size. With brine present, A and phi(0) varied linearly with stress. The initial void fraction was also dependent to some extent on the particle size distribution. The rate of consolidation was most rapid in brine and least rapid in the presence of only air as the fluid. A brine containing 5 m MgCl 2 showed an intermediate rate, presumably because of the greatly reduced solubility of NaCl. A substantial wall effect was indicated by an observed increase in the void fraction of consolidated columns with distance from the top where the stress was applied and by a dependence of consolidation rate on the column height and radius. The distance through which the stress fell by a factor of phi was estimated to change inversely as the fourth power of the column diameter. With increasing temperature (to 85 0 C), consolidation proceeded somewhat more rapidly and the wall effect was reduced. The permeability of the columns dropped rapidly with consolidation, decreasing with about the sixth power of the void fraction. In general, extrapolation of the results to repository conditions confirms the self-sealing properties of bedded salt as a storage medium for radioactive waste

  1. Field Investigation of Natural Attenuation of a Petroleum Hydrocarbon Contaminated Aquifer, Gyeonggi Province, Korea

    Science.gov (United States)

    Yang, J.; Lee, K.; Bae, G.

    2004-12-01

    In remediation of a petroleum hydrocarbon contaminated aquifer, natural attenuation may be significant as a remedial alternative. Therefore, natural attenuation should be investigated in the field in order to effectively design and evaluate the remediation strategy at the contaminated site. This study focused on evaluating the natural attenuation for benzene, toluene, ethylbenzene, and xylene (BTEX) at a contaminated site in South Korea. At the study site, the aquifer is composed of a high permeable gravel layer and relatively low permeable sandy-silt layers. Groundwater level vertically fluctuated between 1m and 2m throughout the year (April, 2003~June, 2004) and showed direct response to rainfall events. Chemical analyses of sampled groundwater were performed to investigate the concentrations of various chemical species which are associated with the natural attenuation processes. To evaluate the degree of the biodegradation, the expressed biodegradation capacity (EBC) analysis was done using aerobic respiration, nitrate reduction, manganese reduction, ferric iron reduction, and sulfate reduction as an indicator. High EBC value of sulfate indicate that anaerobic biodegradation by sulfate reduction was a dominant process of mineralization of BTEX at this site. The EBC values decrease sensitively when heavy rainfall occurs due to the dilution and inflow of electron acceptors through a gravel layer. The first-order biodegradation rates of BTEX were estimated by means of the Buscheck and Alcantar method (1995). Results show that the natural attenuation rate of benzene was the highest among the BTEX.

  2. Surface Complexation Modeling of Calcite Zeta Potential Measurement in Mixed Brines for Carbonate Wettability Characterization

    Science.gov (United States)

    Song, J.; Zeng, Y.; Biswal, S. L.; Hirasaki, G. J.

    2017-12-01

    We presents zeta potential measurements and surface complexation modeling (SCM) of synthetic calcite in various conditions. The systematic zeta potential measurement and the proposed SCM provide insight into the role of four potential determining cations (Mg2+, SO42- , Ca2+ and CO32-) and CO2 partial pressure in calcite surface charge formation and facilitate the revealing of calcite wettability alteration induced by brines with designed ionic composition ("smart water"). Brines with varying potential determining ions (PDI) concentration in two different CO2 partial pressure (PCO2) are investigated in experiments. Then, a double layer SCM is developed to model the zeta potential measurements. Moreover, we propose a definition for contribution of charged surface species and quantitatively analyze the variation of charged species contribution when changing brine composition. After showing our model can accurately predict calcite zeta potential in brines containing mixed PDIs, we apply it to predict zeta potential in ultra-low and pressurized CO2 environments for potential applications in carbonate enhanced oil recovery including miscible CO2 flooding and CO2 sequestration in carbonate reservoirs. Model prediction reveals that pure calcite surface will be positively charged in all investigated brines in pressurized CO2 environment (>1atm). Moreover, the sensitivity of calcite zeta potential to CO2 partial pressure in the various brine is found to be in the sequence of Na2CO3 > Na2SO4 > NaCl > MgCl2 > CaCl2 (Ionic strength=0.1M).

  3. Production and characterization of a functional Iranian white brined cheese by replacement of dairy fat with vegetable oils.

    Science.gov (United States)

    Achachlouei, B Fathi; Hesari, J; Damirchi, S Azadmard; Peighambardoust, Sh; Esmaiili, M; Alijani, S

    2013-10-01

    Full-fat cheese usually contains high amounts of saturated fatty acids and cholesterol, which may have negative health effects. In this study, full-fat white brined cheese, as a control sample, and experimental cheeses with olive and canola oils (T1, white brined cheese containing 50% canola oil, T2, white brined cheese containing 50% olive oil, T3, white brined cheese containing 100% canola oil and T4, white brined cheese containing 100% olive oil) were prepared from bovine milk. Physicochemical properties, lipolysis, proteolysis patterns and sensorial properties in the prepared samples were determined during 80 days of storage at 20-day intervals. Cheese incorporating vegetable oils showed lower amounts of saturated fatty acids and higher amounts of unsaturated fatty acids compared with the full-fat cheese (control) samples. Moisture, pH, lipolysis value, as assessed by the acid-degree value, and proteolysis values (pH 4.6 SN/TN% and NPN/TN%) significantly (p titrable acidity decreased during 40 days of ripening but then increased slightly. Sensory properties of white brined cheese incorporating with vegetable oils were different from those of full-fat cheese samples. White brined cheese containing olive and canola oils (100% fat substitution) received better sensory scores compared to other samples. The results showed that it is possible to replace dairy fat with olive and canola oils, which can lead to produce a new healthy and functional white brined cheese.

  4. Development of a Rapid, Nondestructive Method to Measure Aqueous Carbonate in High Salinity Brines Using Raman Spectroscopy

    Science.gov (United States)

    McGraw, L.; Phillips-Lander, C. M.; Elwood Madden, A. S.; Parnell, S.; Elwood Madden, M.

    2015-12-01

    Traditional methods of quantitative analysis are often ill-suited to determining the bulk chemistry of high salinity brines due to their corrosive and clogging properties. Such methods are also often difficult to apply remotely in planetary environments. However, Raman spectroscopy can be used remotely without physical contact with the fluid and is not affected by many ionic brines. Developing methods to study aqueous carbonates is vital to future study of brines on Mars and other planetary bodies, as they can reveal important information about modern and ancient near-surface aqueous processes. Both sodium carbonate standards and unknown samples from carbonate mineral dissolution experiments in high salinity brines were analyzed using a 532 nm laser coupled to an inVia Renishaw spectrometer to collect carbonate spectra from near-saturated sodium chloride and sodium sulfate brines. A calibration curve was determined by collecting spectra from solutions of known carbonate concentrations mixed with a pH 13 buffer and a near-saturated NaCl or Na2SO4 brine matrix. The spectra were processed and curve fitted to determine the height ratio of the carbonate peak at 1066 cm-1 to the 1640 cm-1 water peak. The calibration curve determined using the standards was then applied to the experimental data after accounting for dilutions. Concentrations determined based on Raman spectra were compared against traditional acid titration measurements. We found that the two techniques vary by less than one order of magnitude. Further work is ongoing to verify the method and apply similar techniques to measure aqueous carbonate concentrations in other high salinity brines.Traditional methods of quantitative analysis are often ill-suited to determining the bulk chemistry of high salinity brines due to their corrosive and clogging properties. Such methods are also often difficult to apply remotely in planetary environments. However, Raman spectroscopy can be used remotely without physical

  5. Petroleum and natural gas economy in Arab Countries, in Angola, Iran and Nigeria

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    This paper gives informations on petroleum and natural gas industry, petroleum market and prices, trade and contracts, prospection and investments. BEI (European Bank of Investment) has given its agreement for the financing of the Maghreb-Europe natural gas pipeline in Morocco but will not participate for the piece in Algeria. Several new petroleum or natural gas discoveries have been pointed out (Rhourde Yacoub in Algeria, Shabwa in Yemen, Port Fouad in Egypt). Shell Company has signed an agreement for the development of Pars Nord natural gas field in Iran and has obtained an exploration offshore permit in Angola

  6. Ex-USSR: petroleum activities in 1991

    International Nuclear Information System (INIS)

    1992-01-01

    This paper gives statistical data on economy and petroleum industry in ex-USSR: Primary energy production and consumption (coal, petroleum, natural gas, primary power), petroleum and natural gas reserves, drilling activity, exports and imports of petroleum products, refining capacity. 2 figs., 14 tabs

  7. A deep sea community at the Kebrit brine pool in the Red Sea

    KAUST Repository

    Vestheim, Hege

    2015-02-26

    Approximately 25 deep sea brine pools occur along the mid axis of the Red Sea. These hypersaline, anoxic, and acidic environments have previously been reported to host diverse microbial communities. We visited the Kebrit brine pool in April 2013 and found macrofauna present just above the brine–seawater interface (~1465 m). In particular, inactive sulfur chimneys had associated epifauna of sea anemones, sabellid type polychaetes, and hydroids, and infauna consisting of capitellid polychaetes, gastropods of the genus Laeviphitus (fam. Elachisinidae), and top snails of the family Cocculinidae. The deep Red Sea generally is regarded as extremely poor in benthos. We hypothesize that the periphery along the Kebrit holds increased biomass and biodiversity that are sustained by prokaryotes associated with the brine pool or co-occurring seeps.

  8. Successful field and laboratory tests of advanced phytoremediation systems for decontamination of petroleum and salt impacted soils

    Energy Technology Data Exchange (ETDEWEB)

    Greenberg, B.; Huang, X.D.; Gerhardt, K.; Gurska, J.; Yu, X.M.; MacNeill, G.; Lu, X.; Nykamp, J.; Glick, B.; Wang, W.; Wang, H.; Wu, S.; Knezevich, N.; Gerwing, P. [Waterloo Univ., ON (Canada)]|[Earthmaster Environmental Strategies Inc., Calgary, AB (Canada)]|[Waterloo Environmental Biotechnology Inc., Waterloo, ON (Canada)

    2008-07-01

    This presentation discussed the advantages of phytoremediation and provided an overview of a phytoremediation tests results for petroleum and salt remediation. Several examples of remediation methods were discussed, including the dig and dump method; soil incineration; chemical extraction; electrokinetic separation and land farming/natural attenuation. The advantages of phytoremediation include improved natural structure and texture of soil; suitability to most regions and climates because it is driven by solar energy; cost effectiveness and technically feasible; reasonable time frame for restoration; promotion of high rhizosphere activity by plants; and effective use at remote sites. The development and proof of plant growth promoting rhizobacteria (PGPR) enhanced phytoremediation systems (PEPS) was then addressed. A description of the PEPS was provided. This presentation also reviewed the interaction of a PGPR containing ACC deaminase with a plant seed or root; research and development of the PEPS for PHC remediation; the use of petroleum remediation on an Imperial Oil Sarnia land farm; proof of concept of the application of the PEPS for PHC remediation in Hinton, Alberta; and development of the PEPS for salt impacted sites. Field work and the characteristics of soils were also examined. It was concluded that the PEPS has great potential for efficient remediation of organic, salt and metal contaminated sites and that PGPR alleviates stress and promotes growth resulting in low ethylene and high auxin content. tabs., figs.

  9. Microbial succession and the functional potential during the fermentation of Chinese soy sauce brine.

    Science.gov (United States)

    Sulaiman, Joanita; Gan, Han Ming; Yin, Wai-Fong; Chan, Kok-Gan

    2014-01-01

    The quality of traditional Chinese soy sauce is determined by microbial communities and their inter-related metabolic roles in the fermentation tank. In this study, traditional Chinese soy sauce brine samples were obtained periodically to monitor the transitions of the microbial population and functional properties during the 6 months of fermentation process. Whole genome shotgun method revealed that the fermentation brine was dominated by the bacterial genus Weissella and later dominated by the fungal genus Candida. Metabolic reconstruction of the metagenome sequences demonstrated a characteristic profile of heterotrophic fermentation of proteins and carbohydrates. This was supported by the detection of ethanol with stable decrease of pH values. To the best of our knowledge, this is the first study that explores the temporal changes in microbial successions over a period of 6 months, through metagenome shotgun sequencing in traditional Chinese soy sauce fermentation and the biological processes therein.

  10. The hidden face of the petroleum

    International Nuclear Information System (INIS)

    Laurent, E.

    2006-02-01

    For the first time, a book reveals what that was hidden to the public opinions: why the petroleum crisis of 1973 what only a manipulation, an arrangement between the OPEC and the petroleum companies, why the data concerning the petroleum reserves are wrong and increased by the producers countries, how Washington used the Saudi petroleum weapon to create the Soviet Union fall, and why from march 2001 maps of the Iraq (where were drawn the future petroleum explorations) were working documents for the vice President Cheney and petroleum managers for the ''secret society''. (A.L.B.)

  11. A fully-coupled discontinuous Galerkin spectral element method for two-phase flow in petroleum reservoirs

    Science.gov (United States)

    Taneja, Ankur; Higdon, Jonathan

    2018-01-01

    A high-order spectral element discontinuous Galerkin method is presented for simulating immiscible two-phase flow in petroleum reservoirs. The governing equations involve a coupled system of strongly nonlinear partial differential equations for the pressure and fluid saturation in the reservoir. A fully implicit method is used with a high-order accurate time integration using an implicit Rosenbrock method. Numerical tests give the first demonstration of high order hp spatial convergence results for multiphase flow in petroleum reservoirs with industry standard relative permeability models. High order convergence is shown formally for spectral elements with up to 8th order polynomials for both homogeneous and heterogeneous permeability fields. Numerical results are presented for multiphase fluid flow in heterogeneous reservoirs with complex geometric or geologic features using up to 11th order polynomials. Robust, stable simulations are presented for heterogeneous geologic features, including globally heterogeneous permeability fields, anisotropic permeability tensors, broad regions of low-permeability, high-permeability channels, thin shale barriers and thin high-permeability fractures. A major result of this paper is the demonstration that the resolution of the high order spectral element method may be exploited to achieve accurate results utilizing a simple cartesian mesh for non-conforming geological features. Eliminating the need to mesh to the boundaries of geological features greatly simplifies the workflow for petroleum engineers testing multiple scenarios in the face of uncertainty in the subsurface geology.

  12. CO2/ brine substitution experiments at simulated reservoir conditions

    Science.gov (United States)

    Kummerow, Juliane; Spangenberg, Erik

    2015-04-01

    Capillary properties of rocks affect the mobility of fluids in a reservoir. Therefore, the understanding of the capillary pressure behaviour is essential to assess the long-term behaviour of CO2 reservoirs. Beyond this, a calibration of the petrophysical properties on water saturation of reservoir rocks at simulated in situ conditions is crucial for a proper interpretation of field monitoring data. We present a set-up, which allows for the combined measurements of capillary pressure, electric resistivity, and elastic wave velocities under controlled reservoir conditions (pconf = 400 bar, ppore = 180 bar, T = 65 ° C) at different brine-CO2 saturations. The capillary properties of the samples are measured using the micropore membrane technique. The sample is jacketed with a Viton tube (thickness = 4 mm) and placed between two current electrode endcaps, which as well contain pore fluid ports and ultrasonic P and S wave transducers. Between the sample and the lower endcap the hydrophilic semi-permeable micro-pore membrane (pore size = 100 nm) is integrated. It is embedded into filter papers to establish a good capillary contact and to protect the highly sensitive membrane against mechanical damage under load. Two high-precision syringe pumps are used to displace a quantified volume of brine by CO2 and determine the corresponding sample saturation. The fluid displacement induces a pressure gradient along the sample, which corresponds to the capillary pressure at a particular sample saturation. It is measured with a differential pressure sensor in the range between 0 - 0.2 MPa. Drainage and imbibition cycles are performed to provide information on the efficiency of capillary trapping and to get a calibration of the petrophysical parameters of the sample.

  13. Petroleum industry in CIS

    International Nuclear Information System (INIS)

    Vaillaud, P.

    1992-01-01

    This paper gives statistical data on petroleum and natural gas industry in USSR and in Eastern Europe: crude oil and gas production, petroleum and natural gas deposits, exports, fuel consumption, pipelines network (total length, compressor or pump stations), petroleum refineries. This paper describes also air pollution (carbon dioxide and sulfur dioxide) and Environmental effects of coal and lignite using in fossil power plants in Eastern Europe. 17 figs., 7 tabs

  14. Marks on the petroleum fiscality

    International Nuclear Information System (INIS)

    2007-02-01

    This document offers some marks on the petroleum fiscality in France: the taxes as the 'accises' and the 'TVA', the part of the taxes in the sale price at the service station, the comparison with other countries of Europe, the tax revenues and the Government budget. It provides also marks on the fuels prices formation (margins), the world petroleum markets (supply and demand) and the part of the petroleum companies on the petroleum market. (A.L.B.)

  15. Methodology Measuring Rare Earth Elements in High TDS Reservoir Brines Application as Natural Tracers in CCUS Studies

    Science.gov (United States)

    Smith, W.; Mcling, T. L.; Smith, R. W.; Neupane, H.

    2013-12-01

    .g. Ba) and enriching the REE up to 100X for analysis. The procedures are straightforward, inexpensive, and require little infrastructure, using only single chromatography columns with inexpensive, reusable, commercially available resins and wash chemicals. The procedures have been tested with synthetic brines and waters (up to 250,000 ppm TDS) and field water samples (up to 5,000 ppm TDS). Testing has produced data with REE capture efficiency exceeding 95%, while reducing interfering elements by more than 93%. Further method development and testing continues in preparation for brine analysis of waters from the Big Sky Carbon Sequestration Partnership's Kevin Dome Pilot Study and the University of Wyoming's Carbon Institutes Rock Springs Uplift.

  16. Geologic technical assessment of the Stratton Ridge salt dome, Texas, for potential expansion of the U.S. strategic petroleum reserve.

    Energy Technology Data Exchange (ETDEWEB)

    Rautman, Christopher Arthur; Snider, Anna C.; Looff, Karl M. (Geologic Consultant, Lovelady, TX)

    2006-11-01

    The Stratton Ridge salt dome is a large salt diapir located only some ten miles from the currently active Strategic Petroleum Reserve Site at Bryan Mound, Texas. The dome is approximately 15 miles south-southwest of Houston. The Stratton Ridge salt dome has been intensively developed, in the desirable central portions, with caverns for both brine production and product storage. This geologic technical assessment indicates that the Stratton Ridge salt dome may be considered a viable, if less-than-desirable, candidate site for potential expansion of the Strategic Petroleum Reserve (SPR). Past development of underground caverns significantly limits the potential options for use by the SPR. The current conceptual design layout of proposed caverns for such an expansion facility is based upon a decades-old model of salt geometry, and it is unacceptable, according to this reinterpretation of salt dome geology. The easternmost set of conceptual caverns are located within a 300-ft buffer zone of a very major boundary shear zone, fault, or other structural feature of indeterminate origin. This structure transects the salt stock and subdivides it into an shallow western part and a deeper eastern part. In places, the distance from this structural boundary to the design-basis caverns is as little as 150 ft. A 300-ft distance from this boundary is likely to be the minimum acceptable stand-off, from both a geologic and a regulatory perspective. Repositioning of the proposed cavern field is possible, as sufficient currently undeveloped salt acreage appears to be available. However, such reconfiguration would be subject to limitations related to land-parcel boundaries and other existing infrastructure and topographic constraints. More broadly speaking, the past history of cavern operations at the Stratton Ridge salt dome indicates that operation of potential SPR expansion caverns at this site may be difficult, and correspondingly expensive. Although detailed information is

  17. Apparatus for extracting petroleum

    Energy Technology Data Exchange (ETDEWEB)

    Coogan, J

    1921-01-18

    An apparatus for extracting petroleum from petroleum bearing sand or shale is described comprising a container for liquids, the container being divided into a plurality of compartments, an agitator mounted within the container and below the liquid level and having its forward end opening into one of the compartments, means for delivering sand or shale to the forward end of the agitator, means for subjecting the sand or shale to the action of a solvent for the petroleum while the sand or shale is being agitated and is submerged, the first-mentioned compartment being adapted to receive the extracted petroleum and means for removing the treated sand or shale from adjacent the rear end of the agitator.

  18. Characterization of the abundant ≤0.2 μm cell-like particles inhabiting Lake Vida brine, McMurdo Dry Valleys, Antarctica

    Science.gov (United States)

    Kuhn, E.; Ichimura, A.; Peng, V.; Fritsen, C. H.; Murray, A. E.

    2011-12-01

    Most lakes in the McMurdo Dry Valleys are perennially covered with 3 to 6 m of ice, but Lake Vida is frozen from the surface through the lake bed, with ice permeated by brine channels. Brine collected from within the ice of Lake Vida is six times saltier than seawater, anoxic, with temperature of -13.4 C, pH of 6.2, high concentrations of ferrous iron (>300 μM), NH4+ (3.6 mM), and N2O (>58 μM), making it a unique environment. The first analysis of Vida brine microbial community (sampled in 2005) detected a cell rich environment (107 cells/mL), with cells falling into two size classes: ≥0.5 μm (105 cells/mL) and ~0.2 μm (107 cells/mL). Microorganisms in the domain Bacteria were detected, but Eukarya and Archaea were not. The clone library from 2005 identified Bacteria related to the phyla Proteobacteria (γ, δ, and ɛ), Lentisphaera, Firmicutes, Spirochaeta, Bacterioidetes, Actinobacteria, Verrucomicrobia, and candidate Division TM7. Brine samples were collected again in the austral summer of 2010 in which one of the focus areas is interrogating the ~0.2 μm cell size class. Molecular, imaging, and elemental analyses were employed to characterize the population of nano-sized particles (NP) that pass through 0.2 μm filters. The aim of testing was to determine whether or not these particles are cells with a morphology resulting from environmental stresses. These results are being compared to the same analyses applied in the whole brine microbial community. A 0.2 μm filtrate of brine incubated for 25 days at -13 C was collected on a 0.1 μm filter. Analysis of the 16S rRNA gene DGGE profile showed differences in the banding pattern and relative intensity when comparing the 0.2 μm filtrate to the whole brine community. A 16S rRNA clone library from the 0.2 μm filtrate indicated the presence of genera previously described in the 2005 whole brine community clone library like Pscychrobacter, Marinobacter, and members related to candidate Division TM7. Also, the

  19. Nuclear waste repository simulation experiments (brine migration), Asse Mine of the Federal of Germany: Quarterly brine migration data report, July-September 1984

    International Nuclear Information System (INIS)

    Coyle, A.J.; Kalia, H.N.; Eckert, J.L.

    1986-10-01

    The fifth brine migration data status report describes experiments simulating a nuclear waste repository at the 800-m (2624-ft) level of the Asse Salt Mine in the Federal Republic of Germany from May 1983 through September 1984. This report describes the test equipment, the Asse Salt Mine, and the pretest properties of the salt in the test gallery. This report also includes test data for the first 16 months of operations on brine migration rates, borehole pressure, salt temperatures, and thermomechanical behavior of the salt. Annual reports have been prepared for the years 1983 and 1984, describing the test activities on a yearly basis (Rothfuchs et al., 1984, 1986). The duration of the experiments will be approximately 2 years, ending in December 1985. 2 refs., 118 figs., 91 tabs

  20. Long-term brine migration through an engineered shaft seal system

    International Nuclear Information System (INIS)

    Fryar, D.G.; Beach, J.A.; Kelley, V.A.; Knowles, M.K.

    1997-01-01

    The shaft seal system for the Waste Isolation Pilot Plant (WIPP) must provide a barrier to the migration of fluids within the shafts to prevent the release of contaminants to the accessible environment. To investigate the performance of the shaft seal system, a set of fluid flow performance models was developed based upon the physical characteristics of the WIPP shaft seal system and the surrounding geologic media. This paper describes the results of a numerical model used to investigate the long-term potential for brine migration through the shaft seal system. Modeling results demonstrate that the WIPP shaft seal system will effectively limit brine migration within the repository shafts