WorldWideScience

Sample records for rejection processes final

  1. Regarding the rejection performance of a polymeric reverse osmosis membrane for the final purification of two-phase olive mill effluents previously treated by an advanced oxidation process

    International Nuclear Information System (INIS)

    Ochando-Pulido, J.M.; Martínez-Férez, A.

    2017-01-01

    In previous works on olive mill wastewater (OMW), secondary advanced oxidation treatment solved the problem related to the presence of phenolic compounds and considerable chemical oxygen demand. However, the effluent presented a significant salinity after this treatment. In this work, an adequate operation of a reverse osmosis (RO) membrane is addressed to ensure constant performance over a long period of time. In this paper, the effect of the operating parameters on the dynamic membrane rejection performance towards the target species was examined and discussed. Rejection efficiencies of all species were observed to follow a similar pattern, which consisted of slight initial improvement that further decreased over time. Rejection of both divalent ions remained constant at over 99% regardless of the operating conditions. Rejections were noticed to follow the order SO42−> Cl−> NO3− and Ca2+> Mg2+> K+> Na+, as a rule. Divalent species were moderately more highly rejected than monovalent ones, in accordance with their higher charge and molecular size, and sulfate anions were consistently rejected by over 99%. Finally, the RO membrane exiting treated effluent was depleted of the high electro conductivity initially present (above 97% rejection), permitting its re-use as good quality irrigation water (below 1 mS/cm). [es

  2. Development of enhanced sulfur rejection processes

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, R.H.; Luttrell, G.H.; Adel, G.T.; Richardson, P.E.

    1996-03-01

    Research at Virginia Tech led to the development of two complementary concepts for improving the removal of inorganic sulfur from many eastern U.S. coals. These concepts are referred to as Electrochemically Enhanced Sulfur Rejection (EESR) and Polymer Enhanced Sulfur Rejection (PESR) processes. The EESR process uses electrochemical techniques to suppress the formation of hydrophobic oxidation products believed to be responsible for the floatability of coal pyrite. The PESR process uses polymeric reagents that react with pyrite and convert floatable middlings, i.e., composite particles composed of pyrite with coal inclusions, into hydrophilic particles. These new pyritic-sulfur rejection processes do not require significant modifications to existing coal preparation facilities, thereby enhancing their adoptability by the coal industry. It is believed that these processes can be used simultaneously to maximize the rejection of both well-liberated pyrite and composite coal-pyrite particles. The project was initiated on October 1, 1992 and all technical work has been completed. This report is based on the research carried out under Tasks 2-7 described in the project proposal. These tasks include Characterization, Electrochemical Studies, In Situ Monitoring of Reagent Adsorption on Pyrite, Bench Scale Testing of the EESR Process, Bench Scale Testing of the PESR Process, and Modeling and Simulation.

  3. How to Manage Rejected Scientific Papers? UNAIS as Final Solution.

    Science.gov (United States)

    Diana, Alessandro

    2012-01-01

    Before publication, biomedical papers might undergo a very complex process, from journal selection, authors' motivations for submissions, modifications, and final publication or refusal. UNAIS (Unpublished Articles In Science) is an online repository in which authors can publish previously rejected scientific articles or articles that have never been submitted for publication. At UNAIS, authors can also publish the reasons behind the refusals to publication. UNAIS is more than an e-journal: it is a scientific drop box in which scientists can find indicative and negative results, as well as ideas that can inspire others. UNAIS's goal is also to help students and scientists who want to learn how to write scientific articles. UNAIS' aim is to exchange and promote knowledge. Have a look on www.unais.net.

  4. Radiographic rejection index using statistical process control

    International Nuclear Information System (INIS)

    Savi, M.B.M.B.; Camozzato, T.S.C.; Soares, F.A.P.; Nandi, D.M.

    2015-01-01

    The Repeat Analysis Index (IRR) is one of the items contained in the Quality Control Program dictated by brazilian law of radiological protection and should be performed frequently, at least every six months. In order to extract more and better information of IRR, this study presents the Statistical Quality Control applied to reject rate through Statistical Process Control (Control Chart for Attributes ρ - GC) and the Pareto Chart (GP). Data collection was performed for 9 months and the last four months of collection was given on a daily basis. The Limits of Control (LC) were established and Minitab 16 software used to create the charts. IRR obtained for the period was corresponding to 8.8% ± 2,3% and the generated charts analyzed. Relevant information such as orders for X-ray equipment and processors were crossed to identify the relationship between the points that exceeded the control limits and the state of equipment at the time. The GC demonstrated ability to predict equipment failures, as well as the GP showed clearly what causes are recurrent in IRR. (authors) [pt

  5. Sonar waveforms for reverberation rejection, Part IV: Adaptive processing.

    NARCIS (Netherlands)

    IJsselmuide, S.P. van; Deruaz, L.; Been, R.; Doisy, Y.; Beerens, S.P.

    2002-01-01

    For littoral ASW, reverberation is a big problem and rejection of reverberation is of utmost importance. The influence of the transmitted signal on the signal to reverberation ratio has been presented in three preceding papers. In this paper, the influence of improved signal processing on the

  6. Simulation of the transient processes of load rejection under different accident conditions in a hydroelectric generating set

    Science.gov (United States)

    Guo, W. C.; Yang, J. D.; Chen, J. P.; Peng, Z. Y.; Zhang, Y.; Chen, C. C.

    2016-11-01

    Load rejection test is one of the essential tests that carried out before the hydroelectric generating set is put into operation formally. The test aims at inspecting the rationality of the design of the water diversion and power generation system of hydropower station, reliability of the equipment of generating set and the dynamic characteristics of hydroturbine governing system. Proceeding from different accident conditions of hydroelectric generating set, this paper presents the transient processes of load rejection corresponding to different accident conditions, and elaborates the characteristics of different types of load rejection. Then the numerical simulation method of different types of load rejection is established. An engineering project is calculated to verify the validity of the method. Finally, based on the numerical simulation results, the relationship among the different types of load rejection and their functions on the design of hydropower station and the operation of load rejection test are pointed out. The results indicate that: The load rejection caused by the accident within the hydroelectric generating set is realized by emergency distributing valve, and it is the basis of the optimization for the closing law of guide vane and the calculation of regulation and guarantee. The load rejection caused by the accident outside the hydroelectric generating set is realized by the governor. It is the most efficient measure to inspect the dynamic characteristics of hydro-turbine governing system, and its closure rate of guide vane set in the governor depends on the optimization result in the former type load rejection.

  7. Development of recycling processes for clean rejected MOX fuel pellets

    International Nuclear Information System (INIS)

    Khot, P.M.; Singh, G.; Shelke, B.K.; Surendra, B.; Yadav, M.K.; Mishra, A.K.; Afzal, Mohd.; Panakkal, J.P.

    2014-01-01

    Highlights: • Dry and wet (MWDD) methods were developed for 100% recycling of CRO (0.4–44% PuO 2 ). • Dry method showed higher productivity and comparable powder/product characteristics. • MWDD batches demonstrated improved powder/product characteristics to that of virgin. • Second/multiple recycling is possible with MWDD with better powder/product characteristics. • MWDD batches prepared by little milling showed better macroscopic homogeneity to that of virgin. - Abstract: The dry and wet recycling processes have been developed for 100% recycling of Clean Reject Oxide (CRO) generated during the fabrication of MOX fuel, as CRO contains significant amount of plutonium. Plutonium being strategic material need to be circumvented from its proliferation issues related to its storage for long period. It was difficult to recycle CRO containing higher Pu content even with multiple oxidation and reduction steps. The mechanical recycling comprising of jaw crushing and sieving has been coupled with thermal pulverization for recycling CRO with higher Pu content in dry recycling technique. In wet recycling, MicroWave Direct Denitration (MWDD) technique has been developed for 100% recycling of CRO. The powder prepared by dry and wet (MWDD) recycling techniques was characterized by XRD and BET techniques and their effects on the pellets were evaluated. (U,21%Pu)O 2 pellets fabricated from virgin powder and MWDD were characterized using optical microscopy and α-autoradiography and the results obtained were compared

  8. Management and Handling of Rejected Fuel of MTR Type and Process Effluents Contained Uranium at FEPI

    International Nuclear Information System (INIS)

    Ghaib Widodo; Bambang Herutomo

    2007-01-01

    Research Reactor Fuel Element Production Installation (FEPI) - Serpong has performed management and handling of all kinds of rejected fuel material during production (solids, liquids, and gases) and process effluents contained uranium. The methods that has been implemented are precipitation, absorption, evaporation, electrolysis, and electrodialysis. By these methods will finally be obtained forms of product which can be used directly as fuel material feed and solid/liquid radioactive waste that fulfil the requirements (uranium contents < 50 ppm) to be send to Radioactive Waste Management Installation. (author)

  9. Plant-wide (BSM2) evaluation of reject water treatment with a SHARON-Anammox process

    DEFF Research Database (Denmark)

    Volcke, Eveline; Gernaey, Krist; Vrecko, Darko

    2006-01-01

    treatment plant, reject water treatment with a combined SHARON-Anammox process seems a promising option. The simulation results indicate that significant improvements of the effluent quality of the main wastewater treatment plant can be realized. An economic evaluation of the different scenarios......In wastewater treatment plants (WWTPs) equipped with sludge digestion and dewatering systems, the reject water originating from these facilities contributes significantly to the nitrogen load of the activated sludge tanks, to which it is typically recycled. In this paper, the impact of reject water...

  10. Enhanced IMC design of load disturbance rejection for integrating and unstable processes with slow dynamics.

    Science.gov (United States)

    Liu, Tao; Gao, Furong

    2011-04-01

    In view of the deficiencies in existing internal model control (IMC)-based methods for load disturbance rejection for integrating and unstable processes with slow dynamics, a modified IMC-based controller design is proposed to deal with step- or ramp-type load disturbance that is often encountered in engineering practices. By classifying the ways through which such load disturbance enters into the process, analytical controller formulae are correspondingly developed, based on a two-degree-of-freedom (2DOF) control structure that allows for separate optimization of load disturbance rejection from setpoint tracking. An obvious merit is that there is only a single adjustable parameter in the proposed controller, which in essence corresponds to the time constant of the closed-loop transfer function for load disturbance rejection, and can be monotonically tuned to meet a good trade-off between disturbance rejection performance and closed-loop robust stability. At the same time, robust tuning constraints are given to accommodate process uncertainties in practice. Illustrative examples from the recent literature are used to show effectiveness and merits of the proposed method for different cases of load disturbance. Copyright © 2010. Published by Elsevier Ltd.

  11. Study of the sodalite Bayer synthesis process from reject of kaolin of the Amazon region, Brazil

    International Nuclear Information System (INIS)

    Maia, A.A.B.; Neves, R.F.; Angelica, R.S.; Pöllmann, H.

    2011-01-01

    This work presents an application for the kaolin rejects from Amazonia through the synthesis of sodalite, in addition, the series of sodalites was synthesized with the same conditions of the Bayer process to understand and control their formation when necessary. These tailings are generated by companies located in the state of Para and are mainly composed of kaolinite, thus forming an excellent starting material for the production of zeolites. The synthesis process was carried out in autoclaves and two synthesis temperatures, 150 and 200 deg C, were evaluated, the same ones used in the Bayer process. The anions used in the reaction mixture to obtain the sodalite series were: carbonate chloride and sulfate, and NaOH solution was used as the sodium source. Sodalite was produced in all the synthesis conditions, showing that through the kaolin rejects from the Amazon it was possible to study the sodalite synthesis process.

  12. Process Engineering App lied to the Production of Bioethanol Using Banana Rejection Urabá

    Directory of Open Access Journals (Sweden)

    Daniel Flórez Alvarado

    2012-06-01

    Full Text Available Most countries either financially or in advanced stages of development are faced with the problem of disposal and treatment of waste and organic waste; these can be treated in different ways, for example by reducing its volume or processing any useful substance using physicochemical transformation processesbananas in bioethanol and analyzing environmental impacts to meet sanitary standards.The objective of this study was to evaluate the potential for ethanol production from banana and the study and application of process engineering in ethanol production using banana rejection as feedstock in the region of Urabá.Bioethanol is obtained by fermentation and distillation of rejected bananas where the results are reflected in the operational controls and leaf pattern obtained in the standardization process.

  13. Pain Processing after Social Exclusion and Its Relation to Rejection Sensitivity in Borderline Personality Disorder.

    Directory of Open Access Journals (Sweden)

    Melanie Bungert

    Full Text Available There is a general agreement that physical pain serves as an alarm signal for the prevention of and reaction to physical harm. It has recently been hypothesized that "social pain," as induced by social rejection or abandonment, may rely on comparable, phylogenetically old brain structures. As plausible as this theory may sound, scientific evidence for this idea is sparse. This study therefore attempts to link both types of pain directly. We studied patients with borderline personality disorder (BPD because BPD is characterized by opposing alterations in physical and social pain; hyposensitivity to physical pain is associated with hypersensitivity to social pain, as indicated by an enhanced rejection sensitivity.Twenty unmedicated female BPD patients and 20 healthy participants (HC, matched for age and education played a virtual ball-tossing game (cyberball, with the conditions for exclusion, inclusion, and a control condition with predefined game rules. Each cyberball block was followed by a temperature stimulus (with a subjective pain intensity of 60% in half the cases. The cerebral responses were measured by functional magnetic resonance imaging. The Adult Rejection Sensitivity Questionnaire was used to assess rejection sensitivity.Higher temperature heat stimuli had to be applied to BPD patients relative to HCs to reach a comparable subjective experience of painfulness in both groups, which suggested a general hyposensitivity to pain in BPD patients. Social exclusion led to a subjectively reported hypersensitivity to physical pain in both groups that was accompanied by an enhanced activation in the anterior insula and the thalamus. In BPD, physical pain processing after exclusion was additionally linked to enhanced posterior insula activation. After inclusion, BPD patients showed reduced amygdala activation during pain in comparison with HC. In BPD patients, higher rejection sensitivity was associated with lower activation differences during

  14. Emotional, Cognitive and Self-Enhancement Processes in Aggressive Behavior After Interpersonal Rejection and Exclusion

    OpenAIRE

    Joanna Rajchert

    2015-01-01

    The relationship between exclusion or rejection and aggression is already well documented, but there is still a debate about the mechanisms that underlie this effect. In two studies we focused on the propensity to react aggressively (readiness for aggression) on the bases of emotional, cognitive or self-enhancement (personality-immanent) processes. In both studies we first measured readiness for aggression and then ego-depleted participants. Next, in Study 1 we excluded participants (n = 96) ...

  15. Emotional, Cognitive and Self-Enhancement Processes in Aggressive Behavior After Interpersonal Rejection and Exclusion.

    Science.gov (United States)

    Rajchert, Joanna

    2015-11-01

    The relationship between exclusion or rejection and aggression is already well documented, but there is still a debate about the mechanisms that underlie this effect. In two studies we focused on the propensity to react aggressively (readiness for aggression) on the bases of emotional, cognitive or self-enhancement (personality-immanent) processes. In both studies we first measured readiness for aggression and then ego-depleted participants. Next, in Study 1 we excluded participants (n = 96) using an online ball throwing game and measured displaced aggressive behavior - intensity and duration of an unpleasant noise administrated to a stranger. In Study 2 participants (n = 140) were rejected by a peer on the basis of an interview that they gave and then could retaliate by reducing peer's chance for getting a job. The results show that exclusion effect on displaced aggression was moderated by cognitive readiness for aggression, while rejection effect on retaliatory aggression was shaped by emotional and personality-immanent readiness for aggression as well as ego-depletion. The results were discussed in light of the strength model of self-control by Baumeister, Vohs, and Tice (2007).

  16. Emotional, Cognitive and Self-Enhancement Processes in Aggressive Behavior After Interpersonal Rejection and Exclusion

    Directory of Open Access Journals (Sweden)

    Joanna Rajchert

    2015-11-01

    Full Text Available The relationship between exclusion or rejection and aggression is already well documented, but there is still a debate about the mechanisms that underlie this effect. In two studies we focused on the propensity to react aggressively (readiness for aggression on the bases of emotional, cognitive or self-enhancement (personality-immanent processes. In both studies we first measured readiness for aggression and then ego-depleted participants. Next, in Study 1 we excluded participants (n = 96 using an online ball throwing game and measured displaced aggressive behavior - intensity and duration of an unpleasant noise administrated to a stranger. In Study 2 participants (n = 140 were rejected by a peer on the basis of an interview that they gave and then could retaliate by reducing peer's chance for getting a job. The results show that exclusion effect on displaced aggression was moderated by cognitive readiness for aggression, while rejection effect on retaliatory aggression was shaped by emotional and personality-immanent readiness for aggression as well as ego-depletion. The results were discussed in light of the strength model of self-control by Baumeister, Vohs, and Tice (2007.

  17. Nonlinear modeling and dynamic analysis of hydro-turbine governing system in the process of load rejection transient

    International Nuclear Information System (INIS)

    Zhang, Hao; Chen, Diyi; Xu, Beibei; Wang, Feifei

    2015-01-01

    Graphical abstract: Nonlinear dynamic transfer coefficients are introduced to the hydro-turbine governing system. In the process of load reject ion transient, the nonlinear dynamical behaviors of the system are studied in detail. - Highlights: • A novel mathematical model of a hydro-turbine governing system is established. • The process of load rejection transient is considered. • Nonlinear dynamic transfer coefficients are introduced to the system. • The bifurcation diagram with the variable t has better engineering significance. • The nonlinear dynamical behaviors of the system are studied in detail. - Abstract: This article pays attention to the mathematical modeling of a hydro-turbine governing system in the process of load rejection transient. As a pioneer work, the nonlinear dynamic transfer coefficients are introduced in a penstock system. Considering a generator system, a turbine system and a governor system, we present a novel nonlinear dynamical model of a hydro-turbine governing system. Fortunately, for the unchanged of PID parameters, we acquire the stable regions of the governing system in the process of load rejection transient by numerical simulations. Moreover, the nonlinear dynamic behaviors of the governing system are illustrated by bifurcation diagrams, Poincare maps, time waveforms and phase orbits. More importantly, these methods and analytic results will present theoretical groundwork for allowing a hydropower station in the process of load rejection transient

  18. Dependency, self-criticism and negative affective responses following imaginary rejection and failure threats: meaning-making processes as moderators or mediators.

    Science.gov (United States)

    Besser, Avi; Priel, Beatriz

    2011-01-01

    This study evaluated the intervening role of meaning-making processes in emotional responses to negative life events based on Blatt's (1974, 2004) formulations concerning the role of personality predispositions in depression. In a pre/post within-subject study design, a community sample of 233 participants reacted to imaginary scenarios of interpersonal rejection and achievement failure. Meaning-making processes relating to threats to self-definition and interpersonal relatedness were examined following the exposure to the scenarios. The results indicated that the personality predisposition of Dependency, but not Self-Criticism predicted higher levels of negative affect following the interpersonal rejection event, independent of baseline levels of negative affect. This effect was mediated by higher levels of negative meaning-making processes related to the effect of the interpersonal rejection scenario on Dependent individuals' senses of interpersonal relatedness and self-worth. In addition, both Self-Criticism and Dependency predicted higher levels of negative affect following the achievement failure event, independent of baseline levels of negative affect. Finally, the effect of Self-Criticism was mediated by higher levels of negative meaning-making processes related to the effect of the achievement failure scenario on self-critical individuals' senses of self-definition.

  19. Trait Self-esteem Moderates Decreases in Self-control Following Rejection: An Information-processing Account

    Science.gov (United States)

    Vandellen, Michelle; Knowles, Megan L.; Krusemark, Elizabeth; Sabet, Raha F.; Campbell, W. Keith; McDowell, Jennifer E.; Clementz, Brett A.

    2012-01-01

    In the current paper, the authors posit that trait self-esteem moderates the relationship between social rejection and decrements in self-control, propose an information-processing account of trait self-esteem’s moderating influence and discuss three tests of this theory. The authors measured trait self-esteem, experimentally manipulated social rejection and assessed subsequent self-control in Studies 1 and 2. Additionally, Study 3 framed a self-control task as diagnostic of social skills to examine motivational influences. Together, the results reveal that rejection impairs self-control, but only among low self-esteem individuals. Moreover, this decrement in self-control only emerged when the task had no social implications—suggesting that low self-esteem individuals exert effort on tasks of social value and are otherwise preoccupied with belonging needs when completing nonsocial tasks. PMID:22611304

  20. Trait Self-esteem Moderates Decreases in Self-control Following Rejection: An Information-processing Account.

    Science.gov (United States)

    Vandellen, Michelle; Knowles, Megan L; Krusemark, Elizabeth; Sabet, Raha F; Campbell, W Keith; McDowell, Jennifer E; Clementz, Brett A

    2012-03-01

    In the current paper, the authors posit that trait self-esteem moderates the relationship between social rejection and decrements in self-control, propose an information-processing account of trait self-esteem's moderating influence and discuss three tests of this theory. The authors measured trait self-esteem, experimentally manipulated social rejection and assessed subsequent self-control in Studies 1 and 2. Additionally, Study 3 framed a self-control task as diagnostic of social skills to examine motivational influences. Together, the results reveal that rejection impairs self-control, but only among low self-esteem individuals. Moreover, this decrement in self-control only emerged when the task had no social implications-suggesting that low self-esteem individuals exert effort on tasks of social value and are otherwise preoccupied with belonging needs when completing nonsocial tasks.

  1. Analysis on influence of guide vanes closure laws of pump-turbine on load rejection transient process

    Science.gov (United States)

    Yao, Z.; Bi, H. L.; Huang, Q. S.; Li, Z. J.; Wang, Z. W.

    2013-12-01

    In load rejection transient process, the sudden shut down of guide vanes may cause units speed rise and a sharp increase in water hammer pressure of diversion system, which endangers the safety operation of the power plant. Adopting reasonable guide vane closure law is a kind of economic and effective measurement to reduce the water hammer pressure and limit rotational speed increases. In this paper, combined with Guangzhou Pumped Storage Power Station plant A, the load rejection condition under different guide vanes closure laws is calculated and the key factor of guide vanes closure laws on the impact of the load rejection transition process is analyzed. The different inflection points, which are the closure modes, on the impact of unit speed change, water level fluctuation of surge tank, and the pressure fluctuation of volute inlet and draft tube inlet are further discussed. By compared with the calculation results, a reasonable guide vanes inflection point position can be determined according to security requirements and a reasonable guide vanes closure law can be attained to effectively coordinate the unit speed rise and the rapid pressure change in the load rejection transient process.

  2. Regarding the rejection performance of a polymeric reverse osmosis membrane for the final purification of two-phase olive mill effluents previously treated by an advanced oxidation process; Sobre la eficiencia del rechazo de una membrana polimérica de ósmosis inversa para la purificación del agua residual de almazara de dos fases, previamente tratada mediante un proceso avanzado de oxidación

    Energy Technology Data Exchange (ETDEWEB)

    Ochando-Pulido, J.M.; Martínez-Férez, A.

    2017-07-01

    In previous works on olive mill wastewater (OMW), secondary advanced oxidation treatment solved the problem related to the presence of phenolic compounds and considerable chemical oxygen demand. However, the effluent presented a significant salinity after this treatment. In this work, an adequate operation of a reverse osmosis (RO) membrane is addressed to ensure constant performance over a long period of time. In this paper, the effect of the operating parameters on the dynamic membrane rejection performance towards the target species was examined and discussed. Rejection efficiencies of all species were observed to follow a similar pattern, which consisted of slight initial improvement that further decreased over time. Rejection of both divalent ions remained constant at over 99% regardless of the operating conditions. Rejections were noticed to follow the order SO42−> Cl−> NO3− and Ca2+> Mg2+> K+> Na+, as a rule. Divalent species were moderately more highly rejected than monovalent ones, in accordance with their higher charge and molecular size, and sulfate anions were consistently rejected by over 99%. Finally, the RO membrane exiting treated effluent was depleted of the high electro conductivity initially present (above 97% rejection), permitting its re-use as good quality irrigation water (below 1 mS/cm). [Spanish] En trabajos previos con agua residual de almazara, se solucionó el problema en relación a la presencia de compuestos fenólicos y la considerable concentración de material orgánico. Sin embargo, el efluente presentaba una salinidad significativa tras éste. Este trabajo tiene por objetivo estudiar la adecuada operación de una membrana de ósmosis inversa (OI) para asegurar rendimientos constantes por largos períodos de tiempo de operación. Se examina y discute el efecto de los parámetros de operación en el rendimiento dinámico del rechazo de especies diana. Se observó que la eficiencia de rechazo de todas las especies siguió un

  3. Hadron final states in deep inelastic processes

    International Nuclear Information System (INIS)

    Bjorken, J.D.

    1976-05-01

    Lectures are presented dealing mainly with the description and discussion of hadron final states in electroproduction, colliding beams, and neutrino reactions from the point of view of the simple parton model. Also the space-time evolution of final states in the parton model is considered. It is found that the picture of space-time evolution of hadron final states in deep inelastic processes isn't totally trivial and that it can be made consistent with the hypotheses of the parton model. 39 references

  4. When rejection stings: how self-esteem constrains relationship-enhancement processes.

    Science.gov (United States)

    Murray, Sandra L; Rose, Paul; Bellavia, Gina M; Holmes, John G; Kusche, Anna Garrett

    2002-09-01

    Three experiments examined how needs for acceptance might constrain low versus high self-esteem people's capacity to protect their relationships in the face of difficulties. The authors led participants to believe that their partner perceived a problem in their relationship. They then measured perceptions of the partner's acceptance, partner enhancement, and closeness. Low but not high self-esteem participants read too much into problems, seeing them as a sign that their partner's affections and commitment might be waning. They then derogated their partner and reduced closeness. Being less sensitive to rejection, however, high self-esteem participants affirmed their partner in the face of threat. Ironically, chronic needs for acceptance may result in low self-esteem people seeing signs of rejection where none exist, needlessly weakening attachments.

  5. Indicators for Building Process without Final Defects -

    DEFF Research Database (Denmark)

    Jørgensen, Kirsten; Rasmussen, Grane Mikael Gregaard; Thuesen, Christian Langhoff

    2011-01-01

    This article introduces the preliminary data analysis, as well as the underlying theories and methods for identifying the indicators for building process without final defects. Since 2004, the Benchmark Centre for the Danish Construction Sector (BEC) has collected information about legal defects...

  6. Preventing Rejection

    Science.gov (United States)

    ... After the transplant Preventing rejection Post-transplant medications Types of immunosuppressants Switching immunosuppressants Side effects Other medications Generic and brand name drugs Post-transplant tests Infections and immunity Lifestyle changes Health concerns Back to work or ...

  7. Graft rejection as a Th1-type process amenable to regulation by donor Th2-type cells through an interleukin-4/STAT6 pathway.

    Science.gov (United States)

    Mariotti, Jacopo; Foley, Jason; Ryan, Kaitlyn; Buxhoeveden, Nicole; Kapoor, Veena; Amarnath, Shoba; Fowler, Daniel H

    2008-12-01

    Graft rejection has been defined as the mirror image of graft-versus-host disease, which is biologically characterized primarily as a Th1-type process. As such, we reasoned that graft rejection would represent a Th1 response amenable to Th2 modulation. Indeed, adoptive transfer of host Th1-type cells mediated rejection of fully MHC-disparate murine bone marrow allografts more effectively than host Th2-type cells. Furthermore, STAT1-deficient host T cells did not differentiate into Th1-type cells in vivo and failed to mediate rejection. We next hypothesized that donor Th2 cell allograft augmentation would prevent rejection by modulation of the host Th1/Th2 balance. In the setting of donor Th2 cell therapy, host-anti-donor allospecific T cells acquired Th2 polarity, persisted posttransplantation, and did not mediate rejection. Abrogation of rejection required donor Th2 cell IL-4 secretion and host T-cell STAT6 signaling. In conclusion, T cell-mediated marrow graft rejection primarily resembles a Th1-type process that can be abrogated by donor Th2 cell therapy that promotes engraftment through a novel mechanism whereby cytokine polarization is transferred to host T cells.

  8. Development of an alternative process for recovery of uranium from rejected plates in the manufacture of MTR type fuel elements

    International Nuclear Information System (INIS)

    Flores Gonzalez, Jocelyn Natalia

    2011-01-01

    This work discusses the recovery of enriched uranium in U 235 , from fuel plates rejected during the fuel elements manufacturing process for the La Reina Nuclear Studies Center, RECH-1, CCHEN. The plates have an aluminum based alloy coating, AISI-SAE 6061, with U 3 Si 2 powder distributed evenly inside and dispersed in an aluminum matrix. The high cost of enriched uranium means that it must be recovered from plates rejected in the production process because of non-compliance with the plate specifications, and also because some of them undergo destructive testing, to measure the aluminum coating's thickness on each side of the plate. The thickness of the uranium nucleus is measured as well and the size of the defects on the ends of the plate such as 'dog bone' and 'fish tail', that is, for the purposes of quality control. The first step in the process is carried out by dissolving the aluminum in a hot solution of NaOH in order to release the uranium silicide powder that is insoluble in the soda. A second step involves dissolving the uranium silicide in a hot HNO 3 solution, followed by washing and filtering, and then extracting the SX and analyzing its behavior during this stage. During the process 98.9% of the uranium is recovered together with a solution that is enough for the SX process given the experiences that were carried out in the extraction stage

  9. ATAC Process Proof of Concept Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Bri Rolston; Sarah Freeman

    2014-03-01

    Researchers at INL with funding from the Department of Energy’s Office of Electricity Delivery and Energy Reliability (DOE-OE) evaluated a novel approach for near real-time consumption of threat intelligence. Demonstration testing in an industry environment supported the development of this new process to assist the electric sector in securing their critical networks. This report provides the reader with an understanding of the methods used during this proof of concept project. The processes and templates were further advanced with an industry partner during an onsite assessment. This report concludes with lessons learned and a roadmap for final development of these materials for use by industry.

  10. REDUCING REJECTION/REWORK IN PRESSURE DIE CASTING PROCESS BY APPLICATION OF DMAIC METHODOLOGY OF SIX SIGMA

    Directory of Open Access Journals (Sweden)

    Javedhusen Malek

    2015-12-01

    Full Text Available In today's ever-changing customer driven market, industries are needed to improve their products and processes to satisfy customer requirements. The Six Sigma approach has set a new paradigm of business excellence. Six Sigma as a process driven improvement methodology has been adopted successfully by many industries. From the review of various literatures, it is revealed that Six Sigma is well adopted in large scale enterprise but having less evidence of adoption in Indian SMEs. This paper is focused on providing path to Indian SMEs for initiating Six Sigma approach in their industries. The paper discusses the real life case where Six Sigma has been successfully applied at one of the Indian small-scale unit to improve rejection/rework rate in manufacturing products by pressure die casting process. This paper describes phase wise application of all the phases of define-measure-analyse-improve-control (DMAIC which also shows impact of Six Sigma in quality improvement.

  11. 40 CFR 61.134 - Standard: Naphthalene processing, final coolers, and final-cooler cooling towers.

    Science.gov (United States)

    2010-07-01

    ... coolers, and final-cooler cooling towers. 61.134 Section 61.134 Protection of Environment ENVIRONMENTAL... Standard: Naphthalene processing, final coolers, and final-cooler cooling towers. (a) No (“zero”) emissions are allowed from naphthalene processing, final coolers and final-cooler cooling towers at coke by...

  12. FINAL REPORT: Transformational electrode drying process

    Energy Technology Data Exchange (ETDEWEB)

    Claus Daniel, C.; Wixom, M.(A123 Systems, Inc.)

    2013-12-19

    This report includes major findings and outlook from the transformational electrode drying project performance period from January 6, 2012 to August 1, 2012. Electrode drying before cell assembly is an operational bottleneck in battery manufacturing due to long drying times and batch processing. Water taken up during shipment and other manufacturing steps needs to be removed before final battery assembly. Conventional vacuum ovens are limited in drying speed due to a temperature threshold needed to avoid damaging polymer components in the composite electrode. Roll to roll operation and alternative treatments can increase the water desorption and removal rate without overheating and damaging other components in the composite electrode, thus considerably reducing drying time and energy use. The objective of this project was the development of an electrode drying procedure, and the demonstration of processes with no decrease in battery performance. The benchmark for all drying data was an 80°C vacuum furnace treatment with a residence time of 18 – 22 hours. This report demonstrates an alternative roll to roll drying process with a 500-fold improvement in drying time down to 2 minutes and consumption of only 30% of the energy compared to vacuum furnace treatment.

  13. Final processing vessel for radioactive waste

    International Nuclear Information System (INIS)

    Tejima, Takaya; Hiraki, Akimitsu.

    1989-01-01

    An inorganic inner layer comprising dense inorganic material such as organic polymer-impregnated concretes is formed to about 10 - 50 mm in average thickness at the inside of a metal vessel. Further, the surface of the vessel is formed as a flat surface with no or only small reinforcing protrusions. Thus, if the final processing vessel should be dropped during transportation or handling by mistake, since impact shocks do not concentrate to protrusions as usual, no local stress concentration occurs to the inorganic inner liner layer. Accordingly, the risk of rapture can be reduced greatly. Further, since impact shock resistance layer put between the metal vessel and the inorganic inner liner layer absorbs shocks, a further sufficient strength can be obtained against dropping accident. (T.M.)

  14. Fundamental Processes in Plasmas. Final report

    International Nuclear Information System (INIS)

    O'Neil, Thomas M.; Driscoll, C. Fred

    2009-01-01

    This research focuses on fundamental processes in plasmas, and emphasizes problems for which precise experimental tests of theory can be obtained. Experiments are performed on non-neutral plasmas, utilizing three electron traps and one ion trap with a broad range of operating regimes and diagnostics. Theory is focused on fundamental plasma and fluid processes underlying collisional transport and fluid turbulence, using both analytic techniques and medium-scale numerical simulations. The simplicity of these systems allows a depth of understanding and a precision of comparison between theory and experiment which is rarely possible for neutral plasmas in complex geometry. The recent work has focused on three areas in basic plasma physics. First, experiments and theory have probed fundamental characteristics of plasma waves: from the low-amplitude thermal regime, to inviscid damping and fluid echoes, to cold fluid waves in cryogenic ion plasmas. Second, the wide-ranging effects of dissipative separatrices have been studied experimentally and theoretically, finding novel wave damping and coupling effects and important plasma transport effects. Finally, correlated systems have been investigated experimentally and theoretically: UCSD experients have now measured the Salpeter correlation enhancement, and theory work has characterized the 'guiding center atoms of antihydrogen created at CERN

  15. A new window of opportunity to reject process-based biotechnology regulation.

    Science.gov (United States)

    Marchant, Gary E; Stevens, Yvonne A

    2015-01-01

    The question of whether biotechnology regulation should be based on the process or the product has long been debated, with different jurisdictions adopting different approaches. The European Union has adopted a process-based approach, Canada has adopted a product-based approach, and the United States has implemented a hybrid system. With the recent proliferation of new methods of genetic modification, such as gene editing, process-based regulatory systems, which are premised on a binary system of transgenic and conventional approaches, will become increasingly obsolete and unsustainable. To avoid unreasonable, unfair and arbitrary results, nations that have adopted process-based approaches will need to migrate to a product-based approach that considers the novelty and risks of the individual trait, rather than the process by which that trait was produced. This commentary suggests some approaches for the design of such a product-based approach.

  16. Cavitational Hydrothermal Oxidation: A New Remediation Process - Final Report; FINAL

    International Nuclear Information System (INIS)

    Suslick, K. S.

    2001-01-01

    During the past year, we have continued to make substantial scientific progress on our understanding of cavitation phenomena in aqueous media and applications of cavitation to remediation processes. Our efforts have focused on three separate areas: sonoluminescence as a probe of conditions created during cavitational collapse in aqueous media, the use of cavitation for remediation of contaminated water, and an addition of the use of ultrasound in the synthesis of novel heterogeneous catalysts for hydrodehalogenation of halocarbons under mild conditions

  17. Bayesian signal processing of pulse shapes for background rejection in the Majorana Demonstrator

    Science.gov (United States)

    Shanks, Benjamin; Majorana Collaboration

    2015-10-01

    The Majorana Demonstrator uses high purity germanium (HPGe) detectors in the p-type point contact (PPC) geometry to search for neutrinoless double-beta decay (0 νββ) in 76Ge. Due to the unique electric potential created within the PPC geometry, the detailed pulse shape depends on the number of energy depositions contained within a given event. Pulse shape analysis (PSA) techniques can be used to estimate the number of separate depositions which combine to form a single pulse. This information can be used to discriminate between 0 νββ candidate events, which deposit energy at a single detector site, and gamma ray background, which can scatter and deposit energy in multiple locations. The problem of determining whether a pulse is single- or multi-site is well suited to Bayesian classifiers. Once trained via supervised machine learning, these algorithms can perform nonlinear cuts against multi-site events using the estimated probability function as a discriminator. The Bayesian approach can also be naturally extended to incorporate a model of the physical process responsible for signal generation within the detector. Presented here is an overview of the Bayesian classifier developed for use on the Demonstrator. This material is based upon work supported by the U.S. Department of Energy, Office of Science, Office of Nuclear Physics, the Particle Astrophysics Program of the National Science Foundation, and the Sanford Underground Research Facility.

  18. Development of the uranium recovery process from rejected fuel plates in the fabrication of MTR type nuclear fuel

    International Nuclear Information System (INIS)

    Fleming Rubio, Peter Alex

    2010-01-01

    The current work was made in Conversion laboratory belonging to Chilean Nuclear Energy Commission, CCHEN. This is constituted by the development of three hydrometallurgical processes, belonging to the recovery of uranium from fuel plates based on uranium silicide (U_3Si_2) process, for nuclear research reactors MTR (Material Testing Reactor) type, those that come from the Fuel Elements Manufacture Plant, PEC. In the manufacturing process some of these plates are subjected to destructive tests by quality requirement or others are rejected for non-compliance with technical specifications, such as: lack of homogenization of the dispersion of uraniferous compound in the meat, as well as the appearance of the defects, such as blisters, so-called "dog bone", "fish tail", "remote islands", among others. Because the uranium used is enriched in 19.75% U_2_3_5 isotope, which explains the high value in the market, it must be recovered for reuse, returning to the production line of fuel elements. The uranium silicide, contained in the plates, is dispersed in an aluminum matrix and covered with plates and frames of ASTM 6061 Aluminum, as a sandwich coating, commonly referred to as 'meat' (sandwich meat). As aluminum is the main impurity, the process begins with this metal dissolution, present in meat and plates, by NaOH reaction, followed by a vacuum filtration, washing and drying, obtaining a powder of uranium silicide, with a small impurities percentage. Then, the crude uranium silicide reacts with a solution of hydrofluoric acid, dissolving the silicon and simultaneously precipitating UF_4 by reaction with HNO_3, obtaining an impure UO_2(NO_3)_2 solution. The experimental work was developed and implemented at laboratory scale for the three stages pertaining to the uranium recovery process, determining for each one the optimum operation conditions: temperature, molarity or concentration, reagent excess, among others (author)

  19. On Gamma Ray Instrument On-Board Data Processing Real-Time Computational Algorithm for Cosmic Ray Rejection

    Science.gov (United States)

    Kizhner, Semion; Hunter, Stanley D.; Hanu, Andrei R.; Sheets, Teresa B.

    2016-01-01

    gamma ray events and the problem is to detect and reject the much more voluminous cosmic ray projections, so that the remaining science data can be telemetered to the ground over the constrained communication link. The state-of-the-art in cosmic rays detection and rejection does not provide an adequate computational solution. This paper presents a novel approach to the AdEPT on-board data processing burdened with the CR detection top pole bottleneck problem. This paper is introducing the data processing object, demonstrates object segmentation and distribution for processing among many processing elements (PEs) and presents solution algorithm for the processing bottleneck - the CR-Algorithm. The algorithm is based on the a priori knowledge that a CR pierces the entire instrument pressure vessel. This phenomenon is also the basis for a straightforward CR simulator, allowing the CR-Algorithm performance testing. Parallel processing of the readout image's (2(N+M) - 4) peripheral voxels is detecting all CRs, resulting in O(n) computational complexity. This algorithm near real-time performance is making AdEPT class spaceflight instruments feasible.

  20. Rockfall Hazard Process Assessment : Final Project Report

    Science.gov (United States)

    2017-10-01

    After a decade of using the Rockfall Hazard Rating System (RHRS), the Montana Department of Transportation (MDT) sought a reassessment of their rockfall hazard evaluation process. Their prior system was a slightly modified version of the RHRS and was...

  1. FY-2010 Process Monitoring Technology Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Orton, Christopher R.; Bryan, Samuel A.; Casella, Amanda J.; Hines, Wes; Levitskaia, Tatiana G.; henkell, J.; Schwantes, Jon M.; Jordan, Elizabeth A.; Lines, Amanda M.; Fraga, Carlos G.; Peterson, James M.; Verdugo, Dawn E.; Christensen, Ronald N.; Peper, Shane M.

    2011-01-01

    During FY 2010, work under the Spectroscopy-Based Process Monitoring task included ordering and receiving four fluid flow meters and four flow visible-near infrared spectrometer cells to be instrumented within the centrifugal contactor system at Pacific Northwest National Laboratory (PNNL). Initial demonstrations of real-time spectroscopic measurements on cold-stream simulants were conducted using plutonium (Pu)/uranium (U) (PUREX) solvent extraction process conditions. The specific test case examined the extraction of neodymium nitrate (Nd(NO3)3) from an aqueous nitric acid (HNO3) feed into a tri-n-butyl phosphate (TBP)/ n-dodecane solvent. Demonstration testing of this system included diverting a sample from the aqueous feed meanwhile monitoring the process in every phase using the on-line spectroscopic process monitoring system. The purpose of this demonstration was to test whether spectroscopic monitoring is capable of determining the mass balance of metal nitrate species involved in a cross-current solvent extraction scheme while also diverting a sample from the system. The diversion scenario involved diverting a portion of the feed from a counter-current extraction system while a continuous extraction experiment was underway. A successful test would demonstrate the ability of the process monitoring system to detect and quantify the diversion of material from the system during a real-time continuous solvent extraction experiment. The system was designed to mimic a PUREX-type extraction process with a bank of four centrifugal contactors. The aqueous feed contained Nd(NO3)3 in HNO3, and the organic phase was composed of TBP/n-dodecane. The amount of sample observed to be diverted by on-line spectroscopic process monitoring was measured to be 3 mmol (3 x 10-3 mol) Nd3+. This value was in excellent agreement with the 2.9 mmol Nd3+ value based on the known mass of sample taken (i.e., diverted) directly from the system feed solution.

  2. Parton dynamics in hadronic processes. Final report

    International Nuclear Information System (INIS)

    Sukhatme, U.P.

    1984-07-01

    We have elucidated several aspects of the dual parton fragmentation model for low transverse momentum multiparticle production in hadronic collisions previously developed by the author and collaborators at Orsay, France. In particular, we have verified that the dual parton model correctly reproduces recently obtained two particle inclusive distributions and particle ratios in the central region of pp and anti pp collisions. This work sheds light on the dynamics of partons in a hadronic collision since it strongly indicates that a valence quark from each initial hadron is held back with a small momentum fraction. Also, we have extended the dual parton approach to include diffraction dissocation and studied the consequences on inclusive pion production in pp interactions. We have investigated the virtues and limitations of logarithmic perturbation theory, which is often a much simpler alternative to standard Rayleigh-Schroedinger perturbation theory. Finally, we have developed and studied the shifted 1/N expansion for the enrgy eigenstates in non-relativistic quantum mechanics. Our results provide an accurate, rapidly convergent, powerful new way of handling any spherically symmetric potential. 18 references

  3. Study of The Final Customer Loyalty Process

    Directory of Open Access Journals (Sweden)

    Juan Carlos Fandos

    2013-12-01

    Full Text Available For any business is important to maintain a loyal customer base to help they to survive over time. This situation is accentuated even to the extent that increases competition and increases uncertainty. At present these are two features that are really developed. Because of the deep crisis in which we are, and other elements such as globalization and the development of new technologies and communication systems, we are faced with a scenario of intense competition and uncertainty manifest. It is therefore more necessary than ever to know in depth how to get customers to be faithful, and develop true loyalty strategies.In this paper, we present the sequential approach to the formation of consumer loyalty in order to deepen understanding of the concept. It is supplemented by studying the combined effect of switching costs as an element that promotes the continuity of the relationship. The results shows that the consumer takes a more cognitive process information in their initial assessments of the service and therefore in the early stages of loyalty. As advances in consumer behavior process becomes more direct and mechanic, so we can say that the customer-company bond is stronger.

  4. Borehole plugging by compaction process. Final report

    International Nuclear Information System (INIS)

    Fernandez, R.; MacGowan, C.; Nolan, E.; Morey, R.; Palty, A.

    1976-08-01

    The requirements of an overall program to preserve the integrity of a repository formation are documented. The repository is intended to be in stable earth stratum used as a safe and permanent storage area for nuclear waste material. These wastes represent an environmental hazard for a period of up to 200,000 years. An engineering analysis, a reliability and quality-assurance program, and a development program for borehole plugging by compaction process, using natural earthen materials, are presented. Part 1 provides the engineering analysis of downhole compaction methods and related instrumentation along with a recommended development plan from concept through a pilot in-situ experiment. Part 2 provides a reliability and quality-assurance program from laboratory testing of materials through an in-situ experiment

  5. Environmental impact of rejected materials generated in organic fraction of municipal solid waste anaerobic digestion plants: Comparison of wet and dry process layout.

    Science.gov (United States)

    Colazo, Ana-Belén; Sánchez, Antoni; Font, Xavier; Colón, Joan

    2015-09-01

    Anaerobic digestion of source separated organic fraction of municipal solid waste is an increasing waste valorization alternative instead of incineration or landfilling of untreated biodegradable wastes. Nevertheless, a significant portion of biodegradable wastes entering the plant is lost in pre-treatments and post-treatments of anaerobic digestion facilities together with other improper materials such as plastics, paper, textile materials and metals. The rejected materials lost in these stages have two main implications: (i) less organic material enters to digesters and, as a consequence, there is a loss of biogas production and (ii) the rejected materials end up in landfills or incinerators contributing to environmental impacts such as global warming or eutrophication. The main goals of this study are (i) to estimate potential losses of biogas in the rejected solid materials generated during the pre- and post-treatments of two full-scale anaerobic digestion facilities and (ii) to evaluate the environmental burdens associated to the final disposal (landfill or incineration) of these rejected materials by means of Life Cycle Assessment. This study shows that there is a lost of potential biogas production, ranging from 8% to 15%, due to the loss of organic matter during pre-treatment stages in anaerobic digestion facilities. From an environmental point of view, the Life Cycle Assessment shows that the incineration scenario is the most favorable alternative for eight out of nine impact categories compared with the landfill scenario. The studied impact categories are Climate Change, Fossil depletion, Freshwater eutrophication, Marine eutrophication, Ozone depletion, Particulate matter formation, Photochemical oxidant formation, Terrestrial acidification and Water depletion. Copyright © 2015 Elsevier Ltd. All rights reserved.

  6. Final Rule for Industrial Process Cooling Towers: Fact Sheet

    Science.gov (United States)

    Fact sheet concerning a final rule to reduce air toxics emissions from industrial process cooling towers. Air toxics are those pollutants known or suspected of causing cancer or other serious health effects.

  7. Mechanisms of allograft rejection of corneal endothelium

    International Nuclear Information System (INIS)

    Tagawa, Y.; Silverstein, A.M.; Prendergast, R.A.

    1982-01-01

    The local intraocular graft-vs.-host (GVH) reaction, involving the destruction of the corneal endothelial cells of the rabbit host by sensitized donor lymphoid cells, has been used to study the mechanism of corneal allograft rejection. Pretreatment of donor cells with a specific mouse monoclonal hybridoma anti-T cell antibody and complement suppresses the destructive reaction, suggesting that a cellular-immune mechanism is primarily involved. Pretreatment of donor cells with mitomycin-C completely abolishes the local GVH reaction, indicating that the effector lymphocytes must undergo mitosis within the eye before they can engage in target cell destruction. Finally, studies of the local GVH reaction in irradiated leukopenic recipients or in preinflamed rabbit eyes suggest that host leukocytes may contribute nonspecifically to enhance the destructive process. These studies show that the local ocular GVH reaction may provide a useful model for the study of the mechanisms involved in the rejection of corneal allografts

  8. Final-state interaction in processes of deuteron breaking

    International Nuclear Information System (INIS)

    Thome Filho, Z.D.

    1974-12-01

    Interaction between particles in the final state of reactions can strongly affect the experimental angular distributions, as in the scattering processes with the breaking of the deuteron target, where the final state interaction is responsible for the disappearance of the differential cross section in the front direction. It is then necessary to include the contribution of the final state interaction to small angles of incoherent processes particle-deuteron. In this work line, an analysis is made of the process πd → πpn for different values of the incident energy. The data obtained are compared with existing experimental data. The hypothesis is also considered of the nucleon which collides with the incident particle being outside the mass layer. An analytical extension of the resonant amplitude πN outwards the mass layer is also used

  9. Space Processing Applications Rocket project, SPAR 1. Final report

    International Nuclear Information System (INIS)

    Reeves, F.; Chassay, R.

    1976-12-01

    The experiment objectives, design/operational concepts, and final results of each of nine scientific experiments conducted during the first Space Processing Applications Rocket (SPAR) flight are summarized. The nine individual SPAR experiments, covering a wide and varied range of scientific materials processing objectives, were entitled: solidification of Pb-Sb eutectic, feasibility of producing closed-cell metal foams, characterization of rocket vibration environment by measurement of mixing of two liquids, uniform dispersions of crystallization processing, direct observation of solidification as a function of gravity levels, casting thoria dispersion-strengthened interfaces, contained polycrystalline solidification, and preparation of a special alloy for manufacturing of magnetic hard superconductor under zero-g environment

  10. Space Processing Applications rocket project SPAR III. Final report

    International Nuclear Information System (INIS)

    Reeves, F.

    1978-01-01

    This document presents the engineering report and science payload III test report and summarizes the experiment objectives, design/operational concepts, and final results of each of five scientific experiments conducted during the third Space Processing Applications Rocket (SPAR) flight flown by NASA in December 1976. The five individual SPAR experiments, covering a wide and varied range of scientific materials processing objectives, were entitled: Liquid Mixing, Interaction of Bubbles with Solidification Interfaces, Epitaxial Growth of Single Crystal Film, Containerless Processing of Beryllium, and Contact and Coalescence of Viscous Bodies

  11. Hadronic final states and sum rules in deep inelastic processes

    International Nuclear Information System (INIS)

    Pal, B.K.

    1977-01-01

    In order to get maximum information on the hadronic final states and sum rules in deep inelastic processes, Regge phenomenology and quarks parton model have been used. The unified picture for the production of hadrons of type i as a function of Bjorken and Feyman variables with only one adjustable parameter is formulated. The results of neutrino experiments and the production of charm particles are discussed in sum rules. (author)

  12. Preemptive scheduling with rejection

    NARCIS (Netherlands)

    Hoogeveen, H.; Skutella, M.; Woeginger, Gerhard

    2003-01-01

    We consider the problem of preemptively scheduling a set of n jobs on m (identical, uniformly related, or unrelated) parallel machines. The scheduler may reject a subset of the jobs and thereby incur job-dependent penalties for each rejected job, and he must construct a schedule for the remaining

  13. Preemptive scheduling with rejection

    NARCIS (Netherlands)

    Hoogeveen, J.A.; Skutella, M.; Woeginger, G.J.; Paterson, M.

    2000-01-01

    We consider the problem of preemptively scheduling a set of n jobs on m (identical, uniformly related, or unrelated) parallel machines. The scheduler may reject a subset of the jobs and thereby incur job-dependent penalties for each rejected job, and he must construct a schedule for the remaining

  14. Effects of surface coating process conditions on the water permeation and salt rejection properties of composite polyamide reverse osmosis membranes

    KAUST Repository

    Louie, Jennifer Sarah; Pinnau, Ingo; Reinhard, Martin

    2011-01-01

    are impacted by the coating process steps, and investigates how such effects could contribute to lower water flux. On one hand, simply pre-soaking dry aromatic polyamide composite membranes in aliphatic alcohols results in a significant increase in water flux

  15. Subcarrier-based Processing for Clutter Rejection in CP-OFDM Signal-based Passive Radar Using SFN Configuration (in English

    Directory of Open Access Journals (Sweden)

    Yi Jian-xin

    2013-03-01

    Full Text Available Clutter rejection is a key technique used by passive radars for target detection. Especially when using Single Frequency Network (SFN configuration, the multipath clutter and ground clutter increase several times more than during a single illuminator situation, which means that the clutter extends in both the spatial and temporal dimensions. The high amount of clutter occupies numerous degrees of freedom when conventional spatial or temporal processing is used, leading to a large array requirement, a huge computational cost, or even a complete failure. This paper investigates a novel subcarrier-based processing technique that is tailored for Orthogonal Frequency Division Multiplex (OFDM modulation with a Cyclic Prefix (CP-OFDM to avoid the abovementioned predicament. The algorithm principle is initially illustrated and followed by a discussion about the unique characteristics of Subcarrier-based Spatial Adaptive Processing (SSAP, which include the Doppler response and its unusual main-lobe clutter case. Then, the robustness is researched by evaluating the performance under relaxed basic assumptions. The conclusions are demonstrated by conducting test using simulated and real data sets.

  16. Dynamics of process at the final stage of nuclear fission

    International Nuclear Information System (INIS)

    Koljari, I.G.; Mavlitov, N.D.

    2005-01-01

    Numerous experimental data show, that the final stage of nuclear fission near to a scission point plays an essential role at formation of characteristics of fission products. At the description of a final stage of fission there is a number of problems: Definition of the form of the nuclear near the scission point and definition forms of a fission fragments; The account of dynamic processes in compound nuclear directly before of fission. The condition of the quasistatic al adiabatic process - dS/dt=0 - is applied in a point of transition from the uniform compound nuclei to several forms for definition of generalized coordinates and speeds. Calculation of dependence of post neutrons from nuclear mass of fission fragments for reactions is α+ 83 Bi 209 → 85 At 213 (E lab = 45 MeV); α+ 92 U 242 → 94 Pu 242 (E lab = 45 MeV); 8 O 18 + 79 Au 197 → 97 Fr 215 (E lab = 159 MeV). System of equations, which describes behaviour of system in a point of nuclear fission-transition from the uniform form to system of a two (and, probably more) fission fragments is given. The system of the equations allows in a fission point to define the generalized coordinates, and the generalized speeds for each of the generalized coordinates of collective deformation variables

  17. Image rejects/retakes--radiographic challenges.

    Science.gov (United States)

    Waaler, D; Hofmann, B

    2010-01-01

    A general held position among radiological personnel prior to digitalisation was that the problem of image rejects/retakes should more or less vanish. However, rejects/retakes still impose several challenges within radiographic imaging; they occupy unnecessary resources, expose patients to unnecessary ionizing radiation and may also indicate suboptimal quality management. The latter is the main objective of this paper, which is based on a survey of international papers published both for screen/film and digital technology. The digital revolution in imaging seems to have reduced the percentage of image rejects/retakes from 10-15 to 3-5 %. The major contribution to the decrease appears to be the dramatic reduction of incorrect exposures. At the same time, rejects/retakes due to lack of operator competence (positioning, etc.) are almost unchanged, or perhaps slightly increased (due to lack of proper technical competence, incorrect organ coding, etc.). However, the causes of rejects/retakes are in many cases defined and reported with reference to radiographers' subjective evaluations. Thus, unless radiographers share common views on image quality and acceptance criteria, objective measurements and assessments of reject/retake rates are challenging tasks. Interestingly, none of the investigated papers employs image quality parameters such as 'too much noise' as categories for rejects/retakes. Surprisingly, no reject/retake analysis seems yet to have been conducted for direct digital radiography departments. An increased percentage of rejects/retakes is related to 'digital skills' of radiographers and therefore points to areas for extended education and training. Furthermore, there is a need to investigate the inter-subjectivity of radiographers' perception of, and attitude towards, both technical and clinical image quality criteria. Finally, there may be a need to validate whether reject/retake rate analysis is such an effective quality indicator as has been asserted.

  18. Image rejects/retakes-radiographic challenges

    International Nuclear Information System (INIS)

    Waaler, D.; Hofmann, B.

    2010-01-01

    A general held position among radiological personnel prior to digitalisation was that the problem of image rejects/retakes should more or less vanish. However, rejects/retakes still impose several challenges within radiographic imaging; they occupy unnecessary resources, expose patients to unnecessary ionizing radiation and may also indicate suboptimal quality management. The latter is the main objective of this paper, which is based on a survey of international papers published both for screen/film and digital technology. The digital revolution in imaging seems to have reduced the percentage of image rejects/retakes from 10-15 to 3-5%. The major contribution to the decrease appears to be the dramatic reduction of incorrect exposures. At the same time, rejects/retakes due to lack of operator competence (positioning, etc.) are almost unchanged, or perhaps slightly increased (due to lack of proper technical competence, incorrect organ coding, etc.). However, the causes of rejects/retakes are in many cases defined and reported with reference to radiographers' subjective evaluations. Thus, unless radiographers share common views on image quality and acceptance criteria, objective measurements and assessments of reject/retake rates are challenging tasks. Interestingly, none of the investigated papers employs image quality parameters such as 'too much noise' as categories for rejects/retakes. Surprisingly, no reject/retake analysis seems yet to have been conducted for direct digital radiography departments. An increased percentage of rejects/retakes is related to 'digital skills' of radiographers and therefore points to areas for extended education and training. Furthermore, there is a need to investigate the inter subjectivity of radiographers' perception of, and attitude towards, both technical and clinical image quality criteria. Finally, there may be a need to validate whether reject/retake rate analysis is such an effective quality indicator as has been asserted

  19. Effects of surface coating process conditions on the water permeation and salt rejection properties of composite polyamide reverse osmosis membranes

    KAUST Repository

    Louie, Jennifer Sarah

    2011-02-01

    The application of polymer surface coatings to improve the fouling resistance of reverse osmosis membranes tends to increase flow resistance across the membrane. This paper presents a systematic analysis on how membrane properties and performance are impacted by the coating process steps, and investigates how such effects could contribute to lower water flux. On one hand, simply pre-soaking dry aromatic polyamide composite membranes in aliphatic alcohols results in a significant increase in water flux, which is attributed to wetting of pores in the selective polyamide layer and to changes in the polymer structure. This flux increase was not readily reversible, based on a 300-h water permeation test. Conversely, drying a wetted membrane led to a decrease in water flux, which we hypothesize is caused by increased interchain hydrogen-bonding in the selective layer. This drop in water flux was not permanent; higher flux was observed if the same wetted/dried membrane was then re-soaked in ethanol prior to the water permeation experiment. An ethanol pre-soaking step also increased water flux of a PEBAX-coated membrane by nearly 70%. In contrast to the reduction in water flux caused by the specific treatment sequence of ethanol-swelling followed by drying, this same sequence actually increased gas transport. The eight- to ten-fold increase in Knudsen diffusion-based gas permeance after this pre-treatment was attributed to an increase in the number or size of membrane defects. © 2010 Elsevier B.V.

  20. Economic assessment of advanced flue gas desulfurization processes. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Bierman, G. R.; May, E. H.; Mirabelli, R. E.; Pow, C. N.; Scardino, C.; Wan, E. I.

    1981-09-01

    This report presents the results of a project sponsored by the Morgantown Energy Technology Center (METC). The purpose of the study was to perform an economic and market assessment of advanced flue gas desulfurization (FGD) processes for application to coal-fired electric utility plants. The time period considered in the study is 1981 through 1990, and costs are reported in 1980 dollars. The task was divided into the following four subtasks: (1) determine the factors affecting FGD cost evaluations; (2) select FGD processes to be cost-analyzed; (3) define the future electric utility FGD system market; and (4) perform cost analyses for the selected FGD processes. The study was initiated in September 1979, and separate reports were prepared for the first two subtasks. The results of the latter two subtasks appear only in this final reprot, since the end-date of those subtasks coincided with the end-date of the overall task. The Subtask 1 report, Criteria and Methods for Performing FGD Cost Evaluations, was completed in October 1980. A slightly modified and condensed version of that report appears as appendix B to this report. The Subtask 2 report, FGD Candidate Process Selection, was completed in January 1981, and the principal outputs of that subtask appear in Appendices C and D to this report.

  1. Plan for advanced microelectronics processing technology application. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Goland, A.N.

    1990-10-01

    The ultimate objective of the tasks described in the research agreement was to identify resources primarily, but not exclusively, within New York State that are available for the development of a Center for Advanced Microelectronics Processing (CAMP). Identification of those resources would enable Brookhaven National Laboratory to prepare a program plan for the CAMP. In order to achieve the stated goal, the principal investigators undertook to meet the key personnel in relevant NYS industrial and academic organizations to discuss the potential for economic development that could accompany such a Center and to gauge the extent of participation that could be expected from each interested party. Integrated of these discussions was to be achieved through a workshop convened in the summer of 1990. The culmination of this workshop was to be a report (the final report) outlining a plan for implementing a Center in the state. As events unfolded, it became possible to identify the elements of a major center for x-ray lithography on Lone Island at Brookhaven National Laboratory. The principal investigators were than advised to substitute a working document based upon that concept in place of a report based upon the more general CAMP workshop originally envisioned. Following that suggestion from the New York State Science and Technology Foundation, the principals established a working group consisting of representatives of the Grumman Corporation, Columbia University, the State University of New York at Stony Brook, and Brookhaven National Laboratory. Regular meetings and additional communications between these collaborators have produced a preproposal that constitutes the main body of the final report required by the contract. Other components of this final report include the interim report and a brief description of the activities which followed the establishment of the X-ray Lithography Center working group.

  2. Complement and hyper acute rejection

    Directory of Open Access Journals (Sweden)

    Al-Rabia Mohammed

    2009-01-01

    Full Text Available Organ transplantation has been a major development in clinical medicine but its success has been marred by the immune system′s capacity to respond to "non-self" cells and tissues. A full molecular understanding of this mechanism and the myriad triggers for immune rejection is yet to be elucidated. Consequently, immunosuppressive drugs remain the mainstay of post-transplant ma-nagement; however, these interventions have side effects such as increased incidence of cancer, post-transplant lymphoproliferative disorders, susceptibility to infection if not managed appro-priately and the inconvenience to the patient of lifelong treatment. Novel therapeutic approaches based on molecular understanding of immunological processes are thus needed in this field. The notion that factors influencing successful transplants might be of use as therapeutic approaches is both scientifically and medically appealing. Recent developments in the understanding of successful transplants are expected to provide new opportunities for safer transplantation. This article reviews the present understanding of the molecular basis of rejection and the role of complement in this process as well as the possibility of generating "intelligent" therapy that better target crucial components of hyper-acute rejections.

  3. "Science" Rejects Postmodernism.

    Science.gov (United States)

    St. Pierre, Elizabeth Adams

    2002-01-01

    The National Research Council report, "Scientific Research in Education," claims to present an inclusive view of sciences in responding to federal attempts to legislate educational research. This article asserts that it narrowly defines science as positivism and methodology as quantitative, rejecting postmodernism and omitting other theories. Uses…

  4. Thallium kinetics in rat cardiac transplant rejection

    International Nuclear Information System (INIS)

    Barak, J.H.; LaRaia, P.J.; Boucher, C.A.; Fallon, J.T.; Buckley, M.J.

    1988-01-01

    Cardiac transplant rejection is a very complex process involving both cellular and vascular injury. Recently, thallium imaging has been used to assess acute transplant rejection. It has been suggested that changes in thallium kinetics might be a sensitive indicator of transplant rejection. Accordingly, thallium kinetics were assessed in vivo in acute untreated rat heterotopic (cervical) transplant rejection. Male Lewis rats weighing 225-250 g received heterotopic heart transplants from syngeneic Lewis rats (group A; n = 13), or allogeneic Brown Norway rats (group B; n = 11). Rats were imaged serially on the 2nd and the 7th postoperative days. Serial cardiac thallium content was determined utilizing data collected every 150 sec for 2 hr. The data were fit to a monoexponential curve and the decay rate constant (/sec) derived. By day 7 all group B hearts had histological evidence of severe acute rejection, and demonstrated decreased global contraction. Group A hearts showed normal histology and contractility. However, thallium uptakes and washout of the two groups were the same. Peak thallium uptake of group B was +/- 3758 1166 counts compared with 3553 +/- 950 counts in the control group A (P = 0.6395); The 2-hr percentage of washout was 12.1 +/- 1.04 compared with 12.1 +/- 9.3 (P = 1.0000); and the decay constant was -0.00002065 +/- 0.00001799 compared with -0.00002202 +/- 0.00001508 (P = 0.8409). These data indicate that in vivo global thallium kinetics are preserved during mild-to-severe acute transplant rejection. These findings suggest that the complex cellular and extracellular processes of acute rejection limit the usefulness of thallium kinetics in the detection of acute transplant rejection

  5. Action against Kruemmel rejected

    International Nuclear Information System (INIS)

    Anon.

    1976-01-01

    In its verdict dated September 2nd, 1976 - 10 A 211/74 -, the administrative court of Schleswig-Holstein at Schleswig has rejected with costs the action of a plaintiff resident in Hessen concerning the contestation of the 2nd partial licence for the erection of a nuclear power station at Kruemmel near Hamburg. The verdict is not subject to appeal. Furthermore, the administrative court of Schleswig-Holstein at Schleswig, in its verdict dated September 2nd, 1976 - 10 A 214/74 - has rejected with costs the actions of eight plaintiffs living in Hamburg and surroundings, concerning the contestation of the 1st, 2nd and 3rd partial licence for the erection of a nuclear power station at Kruemmel near Hamburg. An appeal against this verdict has been lodged at the higher administrative court at Lueneburg. The main gounds for the two judgments are given in full text. (orig./HP) [de

  6. Survey of potential chlorine production processes. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1979-04-01

    This report is part of the ongoing study of industrial electrochemical processes for the purpose of identifying methods of improving energy efficiencies. A computerized literature search of past and current chlorine generation methods was performed to identify basic chlorine production processes. Over 200 pertinent references are cited involving 20 separate and distinct chlorine processes. Each basic process is evaluated for its engineering and economic viability and energy efficiency. A flow diagram is provided for each basic process. Four criteria are used to determine the most promising processes: raw material availability, type and amount of energy required, by-product demand/disposal and status of development. The most promising processes are determined to be the membrane process (with and without catalytic electrodes), Kel-Chlor, Mobay (direct electrolysis of hydrogen chloride), the Shell process (catalytic oxidation of hydrogen chloride) and oxidation of ammonium chloride. Each of these processes is further studied to determine what activities may be pursued.

  7. Dynamic process model of a plutonium oxalate precipitator. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Miller, C.L.; Hammelman, J.E.; Borgonovi, G.M.

    1977-11-01

    In support of LLL material safeguards program, a dynamic process model was developed which simulates the performance of a plutonium (IV) oxalate precipitator. The plutonium oxalate precipitator is a component in the plutonium oxalate process for making plutonium oxide powder from plutonium nitrate. The model is based on state-of-the-art crystallization descriptive equations, the parameters of which are quantified through the use of batch experimental data. The dynamic model predicts performance very similar to general Hanford oxalate process experience. The utilization of such a process model in an actual plant operation could promote both process control and material safeguards control by serving as a baseline predictor which could give early warning of process upsets or material diversion. The model has been incorporated into a FORTRAN computer program and is also compatible with the DYNSYS 2 computer code which is being used at LLL for process modeling efforts.

  8. Dynamic process model of a plutonium oxalate precipitator. Final report

    International Nuclear Information System (INIS)

    Miller, C.L.; Hammelman, J.E.; Borgonovi, G.M.

    1977-11-01

    In support of LLL material safeguards program, a dynamic process model was developed which simulates the performance of a plutonium (IV) oxalate precipitator. The plutonium oxalate precipitator is a component in the plutonium oxalate process for making plutonium oxide powder from plutonium nitrate. The model is based on state-of-the-art crystallization descriptive equations, the parameters of which are quantified through the use of batch experimental data. The dynamic model predicts performance very similar to general Hanford oxalate process experience. The utilization of such a process model in an actual plant operation could promote both process control and material safeguards control by serving as a baseline predictor which could give early warning of process upsets or material diversion. The model has been incorporated into a FORTRAN computer program and is also compatible with the DYNSYS 2 computer code which is being used at LLL for process modeling efforts

  9. 14 CFR 11.31 - How does FAA process direct final rules?

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false How does FAA process direct final rules? 11... PROCEDURAL RULES GENERAL RULEMAKING PROCEDURES Rulemaking Procedures General § 11.31 How does FAA process direct final rules? (a) A direct final rule will take effect on a specified date unless FAA receives an...

  10. Modeling rejection immunity

    Directory of Open Access Journals (Sweden)

    Gaetano Andrea De

    2012-05-01

    Full Text Available Abstract Background Transplantation is often the only way to treat a number of diseases leading to organ failure. To overcome rejection towards the transplanted organ (graft, immunosuppression therapies are used, which have considerable side-effects and expose patients to opportunistic infections. The development of a model to complement the physician’s experience in specifying therapeutic regimens is therefore desirable. The present work proposes an Ordinary Differential Equations model accounting for immune cell proliferation in response to the sudden entry of graft antigens, through different activation mechanisms. The model considers the effect of a single immunosuppressive medication (e.g. cyclosporine, subject to first-order linear kinetics and acting by modifying, in a saturable concentration-dependent fashion, the proliferation coefficient. The latter has been determined experimentally. All other model parameter values have been set so as to reproduce reported state variable time-courses, and to maintain consistency with one another and with the experimentally derived proliferation coefficient. Results The proposed model substantially simplifies the chain of events potentially leading to organ rejection. It is however able to simulate quantitatively the time course of graft-related antigen and competent immunoreactive cell populations, showing the long-term alternative outcomes of rejection, tolerance or tolerance at a reduced functional tissue mass. In particular, the model shows that it may be difficult to attain tolerance at full tissue mass with acceptably low doses of a single immunosuppressant, in accord with clinical experience. Conclusions The introduced model is mathematically consistent with known physiology and can reproduce variations in immune status and allograft survival after transplantation. The model can be adapted to represent different therapeutic schemes and may offer useful indications for the optimization of

  11. 242-A Campaign 99-1 process control plan; FINAL

    International Nuclear Information System (INIS)

    LE, E.Q.

    1999-01-01

    242-A Evaporator 99-1 will process approximately one million gallons of waste from tank 102-AW in June 1999. The process control Plan provides a general description of activities, which will occur during 242-A Evaporator Campaign 99-1 and to document analyses conducted to demonstrate that 102-AW waste is acceptable for processing. Predict is a registered trademark of Risk Decisions England Corporation, United Kingdom

  12. Knowledge and Processes in Design. DPS Final Report.

    Science.gov (United States)

    Pirolli, Peter

    Four papers from a project concerning information-processing characterizations of the knowledge and processes involved in design are presented. The project collected and analyzed verbal protocols from instructional designers, architects, and mechanical engineers. A framework was developed for characterizing the problem spaces of design that…

  13. Removal of organic and inorganic sulfur from Ohio coal by combined physical and chemical process. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Attia, Y.A.; Zeky, M.El.; Lei, W.W.; Bavarian, F.; Yu, S. [Ohio State Univ., Columbus, OH (United States). Dept. of Materials Science and Engineering

    1989-04-28

    This project consisted of three sections. In the first part, the physical cleaning of Ohio coal by selective flocculation of ultrafine slurry was considered. In the second part, the mild oxidation process for removal of pyritic and organic sulfur.was investigated. Finally, in-the third part, the combined effects of these processes were studied. The physical cleaning and desulfurization of Ohio coal was achieved using selective flocculation of ultrafine coal slurry in conjunction with froth flotation as flocs separation method. The finely disseminated pyrite particles in Ohio coals, in particular Pittsburgh No.8 seam, make it necessary to use ultrafine ({minus}500 mesh) grinding to liberate the pyrite particles. Experiments were performed to identify the ``optimum`` operating conditions for selective flocculation process. The results indicated that the use of a totally hydrophobic flocculant (FR-7A) yielded the lowest levels of mineral matters and total sulfur contents. The use of a selective dispersant (PAAX) increased the rejection of pyritic sulfur further. In addition, different methods of floc separation techniques were tested. It was found that froth flotation system was the most efficient method for separation of small coal flocs.

  14. Survey of electrochemical metal winning processes. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Vaaler, L.E.

    1979-03-01

    The subject program was undertaken to find electrometallurgical technology that could be developed into energy saving commercial metal winning processes. Metals whose current production processes consume significant energy (excepting copper and aluminum) are magnesium, zinc, lead, chromium, manganese, sodium, and titanium. The technology of these metals, with the exception of titanium, was reviewed. Growth of titanium demand has been too small to justify the installation of an electrolyte process that has been developed. This fact and the uncertainty of estimates of future demand dissuaded us from reviewing titanium technology. Opportunities for developing energy saving processes were found for magnesium, zinc, lead, and sodium. Costs for R and D and demonstration plants have been estimated. It appeared that electrolytic methods for chromium and manganese cannot compete energywise or economically with the pyrometallurgical methods of producing the ferroalloys, which are satisfactory for most uses of chromium and manganese.

  15. FINAL PROCESS DEPENDENT DIMENSIONAL CHANGES OF DOUBLE KNIT FABRICS

    Directory of Open Access Journals (Sweden)

    Vedat ÖZYAZGAN

    2012-01-01

    Full Text Available In this paper Ne 30/1 cotton yarn obtained by using pure cotton fibers is employed. 1x1, 2x1 and 3x1 Rib fabrics were knitted with yarns at different gauges. During the knitting process, the tension was kept constant. In order to investigate the relaxation on the knitting process fabric samples were treated using three relaxation processes; dry, wet and full respectively. After each relaxation process, stitches dimensions were measured. As a result of these measurements, it is observed that as the relaxation increases the stitches length decreases while the stitches width increases. In rib knitting, As the fabric stretches increases the stitch length increases. As a result it is observed that as the stitch length increases, the width of the stitches increases linearly. In all rib fabrics, increase in the stitch density leads to an increase in the weight of the fabric.

  16. Process applications for geothermal energy resources. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Mikic, B.B.; Meal, H.C.; Packer, M.B.; Guillamon-Duch, H.

    1981-08-01

    The principal goal of the program was to demonstrate economical and technical suitability of geothermal energy as a source of industrial process heat through a cooperative program with industrial firms. To accomplish that: a critical literature survey in the field was performed; a workshop with the paper and pulp industry representatives was organized; and four parallel methods dealing with technical and economical details of geothermal energy use as a source of industrial process heat were developed.

  17. Mathematical modeling of the voloxidation process. Final report

    International Nuclear Information System (INIS)

    Stanford, T.G.

    1979-06-01

    A mathematical model of the voloxidation process, a head-end reprocessing step for the removal of volatile fission products from spent nuclear fuel, has been developed. Three types of voloxidizer operation have been considered; co-current operation in which the gas and solid streams flow in the same direction, countercurrent operation in which the gas and solid streams flow in opposite directions, and semi-batch operation in which the gas stream passes through the reactor while the solids remain in it and are processed batch wise. Because of the complexity of the physical ahd chemical processes which occur during the voloxidation process and the lack of currently available kinetic data, a global kinetic model has been adapted for this study. Test cases for each mode of operation have been simulated using representative values of the model parameters. To process 714 kgm/day of spent nuclear fuel, using an oxidizing atmosphere containing 20 mole percent oxygen, it was found that a reactor 0.7 m in diameter and 2.49 m in length would be required for both cocurrent and countercurrent modes of operation while for semibatch operation a 0.3 m 3 reactor and an 88200 sec batch processing time would be required

  18. The role of CD8+ T cells during allograft rejection

    Directory of Open Access Journals (Sweden)

    V. Bueno

    2002-11-01

    Full Text Available Organ transplantation can be considered as replacement therapy for patients with end-stage organ failure. The percent of one-year allograft survival has increased due, among other factors, to a better understanding of the rejection process and new immunosuppressive drugs. Immunosuppressive therapy used in transplantation prevents activation and proliferation of alloreactive T lymphocytes, although not fully preventing chronic rejection. Recognition by recipient T cells of alloantigens expressed by donor tissues initiates immune destruction of allogeneic transplants. However, there is controversy concerning the relative contribution of CD4+ and CD8+ T cells to allograft rejection. Some animal models indicate that there is an absolute requirement for CD4+ T cells in allogeneic rejection, whereas in others CD4-depleted mice reject certain types of allografts. Moreover, there is evidence that CD8+ T cells are more resistant to immunotherapy and tolerance induction protocols. An intense focal infiltration of mainly CD8+CTLA4+ T lymphocytes during kidney rejection has been described in patients. This suggests that CD8+ T cells could escape from immunosuppression and participate in the rejection process. Our group is primarily interested in the immune mechanisms involved in allograft rejection. Thus, we believe that a better understanding of the role of CD8+ T cells in allograft rejection could indicate new targets for immunotherapy in transplantation. Therefore, the objective of the present review was to focus on the role of the CD8+ T cell population in the rejection of allogeneic tissue.

  19. Development of a reject classification method, applied to the diagnotic of a nuclear reactor core: processing of thermal signals providing from out-of-reactor simulation

    International Nuclear Information System (INIS)

    Smolarz, A.

    1982-07-01

    Development of an evolution detection algorithm which aim is to extend the application field of the form recognition analysis to the diagnosis and follow-up of a complex system: study of the data from the out-of-reactor test loop with forced convection in sodium, study and description of a reject classification algorithm developed in the general point of view of evolution detection. This method is tested with theoretical data and with experimental data provided by the second test loop ISIS [fr

  20. The evaporation of viscose process liquors: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Thornton, R

    1984-01-01

    A program of work aimed at producing designs for an energy efficient process for the evaporation of water from viscose process liquors has been completed. The process uses mechanical vapor recompression in conjunction with a thin plastic heat transfer surface. A bench laboratory evaporation rig was built to prove the technical viability of the process. This was followed by the construction of a research plant at a viscose production site. The capacity of this plant was 100 to 150 kg/h of water evaporated. The construction and operation of a plastic heat exchanger with thin walled plastic tubes was achieved with considerable success. The lining of the concrete containment vessel proved more difficult, and the technique employed may not be the best for commercial units. Heat transfer coefficients of up to 550 Wm/sup -2/ K/sup -1/ were measured on the research plant. These agreed well with results obtained from a mathematical model developed for the process. An optimum design for a commercial unit has been costed and the financial parameters determined. Courtaulds considers that the construction of a demonstration plant is justified. 3 refs., 8 figs.

  1. Chemical-cleaning process evaluation: Westinghouse steam generators. Final report

    International Nuclear Information System (INIS)

    Cleary, W.F.; Gockley, G.B.

    1983-04-01

    The Steam Generator Owners Group (SGOG)/Electric Power Research Institute (EPRI) Steam Generator Secondary Side Chemical Cleaning Program, under develpment since 1978, has resulted in a generic process for the removal of accumulated corrosion products and tube deposits in the tube support plate crevices. The SGOG/EPRI Project S150-3 was established to obtain an evaluation of the generic process in regard to its applicability to Westinghouse steam generators. The results of the evaluation form the basis for recommendations for transferring the generic process to a plant specific application and identify chemical cleaning corrosion guidelines for the materials in Westinghouse Steam Generators. The results of the evaluation, recommendations for plant-specific applications and corrosion guidelines for chemical cleaning are presented in this report

  2. A novel process for methanol synthesis. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Tierney, J.W.; Wender, I.

    1994-01-25

    The use of methanol (MeOH) as a fuel additive and in MTBE production has renewed interest in the search for improved MeOH processes. Commercial processes are characterized by high pressures and temperatures with low per pass conversion (10--12%). Efforts are underway to find improved MeOH synthesis processes. A slurry phase ``concurrent`` synthesis of MeOH/methyl formate (MeF) which operates under relatively mild conditions (100{degrees}C lower than present commercial processes) was the subject of investigation in this work. Evidence for a reaction scheme involving the carbonylation of MeOH to MeF followed by the hydrogenolysis of MeF to two molecules of MeOH -- the net result being the reaction of H{sub 2} with CO to give MeOH via MeF, is presented. Up to 90% per pass conversion and 98% selectivity to methanol at rates comparable to commercial processes have been obtained in spite of the presence of as much as 10,000 ppM CO{sub 2} and 3000 ppM H{sub 2}O in the gas and liquid respectively. The effect of process parameters such as temperature, pressure, H{sub 2}/CO ratio in the reactor, flow rate and catalyst loading were also investigated. The use of temperatures above 170{degrees}C at a pressure of 50 atm results in MeF being the limiting reactant. Small amounts of CH{sub 4} are also formed. Significant MeOH synthesis rates at a pressure in the range of 40--50 atm makes possible the elimination of an upstream shift reactor and the use of an air-blown syngas generator. The nature of the catalysts was studied and correlated with the behavior of the various species in the concurrent synthesis.

  3. New Process for Grain Refinement of Aluminum. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Joseph A. Megy

    2000-09-22

    A new method of grain refining aluminum involving in-situ formation of boride nuclei in molten aluminum just prior to casting has been developed in the subject DOE program over the last thirty months by a team consisting of JDC, Inc., Alcoa Technical Center, GRAS, Inc., Touchstone Labs, and GKS Engineering Services. The Manufacturing process to make boron trichloride for grain refining is much simpler than preparing conventional grain refiners, with attendant environmental, capital, and energy savings. The manufacture of boride grain refining nuclei using the fy-Gem process avoids clusters, salt and oxide inclusions that cause quality problems in aluminum today.

  4. 32 CFR 206.5 - Final proposal process.

    Science.gov (United States)

    2010-07-01

    ... the basis of “educational value for the dollar.” NSEP is interested in funding proposals in areas... institution to integrate the efforts of the proposed program into the educational process? What plans are...) MISCELLANEOUS NATIONAL SECURITY EDUCATION PROGRAM (NSEP) GRANTS TO INSTITUTIONS OF HIGHER EDUCATION § 206.5...

  5. UMTRA Surface Project management action process document: Final. Revision 2

    International Nuclear Information System (INIS)

    1996-06-01

    Title 1 of the UMTRCA authorized the DOE to undertake remedial actions at these designed sites and associated vicinity properties (VP), which contain uranium mill tailings and other residual radioactive materials (RRM) derived from the processing sites. Title 2 of the UMTRCA addresses uranium mill sites that were licensed at the time the UMTRCA was enacted. Cleanup of these Title 2 sites is the responsibility of the licensees. The cleanup of the Title 1 sites has been split into two separate projects: the Surface Project, which deals with the mill buildings, tailings, and contaminated soils at the sites and VPs; and the Ground Water Project, which is limited to the contaminated ground water at the sites. This management action process (MAP) document discusses the Uranium Mill Tailings Remedial Action (UMTRA) Surface Project. Since its inception through March 1996, the Surface Project (hereinafter called the Project) has cleaned up 16 of the 24 designated processing sites and approximately 5,000 VPs, reducing the risk to human health and the environment posed by the uranium mill tailings. Two of the 24 sites, Belfield and Bowman, North Dakota, will not be remediated at the request of the state, reducing the total number of sites to 22. By the start of FY1998, the remaining 6 processing sites and associated VPs will be cleaned up. The remedial action activities to be funded in FY1998 by the FY1998 budget request are remediation of the remaining Grand Junction, Colorado, VPs; closure of the Cheney disposal cell in Grand Junction, Colorado; and preparation of the completion reports for 4 completed sites

  6. Cavitational Hydrothermal Oxidation: A New Remediation Process - Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Suslick, K. S.

    2001-07-05

    During the past year, we have continued to make substantial scientific progress on our understanding of cavitation phenomena in aqueous media and applications of cavitation to remediation processes. Our efforts have focused on three separate areas: sonoluminescence as a probe of conditions created during cavitational collapse in aqueous media, the use of cavitation for remediation of contaminated water, and an addition of the use of ultrasound in the synthesis of novel heterogeneous catalysts for hydrodehalogenation of halocarbons under mild conditions.

  7. UMTRA Surface Project management action process document: Final. Revision 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    Title 1 of the UMTRCA authorized the DOE to undertake remedial actions at these designed sites and associated vicinity properties (VP), which contain uranium mill tailings and other residual radioactive materials (RRM) derived from the processing sites. Title 2 of the UMTRCA addresses uranium mill sites that were licensed at the time the UMTRCA was enacted. Cleanup of these Title 2 sites is the responsibility of the licensees. The cleanup of the Title 1 sites has been split into two separate projects: the Surface Project, which deals with the mill buildings, tailings, and contaminated soils at the sites and VPs; and the Ground Water Project, which is limited to the contaminated ground water at the sites. This management action process (MAP) document discusses the Uranium Mill Tailings Remedial Action (UMTRA) Surface Project. Since its inception through March 1996, the Surface Project (hereinafter called the Project) has cleaned up 16 of the 24 designated processing sites and approximately 5,000 VPs, reducing the risk to human health and the environment posed by the uranium mill tailings. Two of the 24 sites, Belfield and Bowman, North Dakota, will not be remediated at the request of the state, reducing the total number of sites to 22. By the start of FY1998, the remaining 6 processing sites and associated VPs will be cleaned up. The remedial action activities to be funded in FY1998 by the FY1998 budget request are remediation of the remaining Grand Junction, Colorado, VPs; closure of the Cheney disposal cell in Grand Junction, Colorado; and preparation of the completion reports for 4 completed sites.

  8. Mixing Processes in High-Level Waste Tanks - Final Report

    International Nuclear Information System (INIS)

    Peterson, P.F.

    1999-01-01

    The mixing processes in large, complex enclosures using one-dimensional differential equations, with transport in free and wall jets is modeled using standard integral techniques. With this goal in mind, we have constructed a simple, computationally efficient numerical tool, the Berkeley Mechanistic Mixing Model, which can be used to predict the transient evolution of fuel and oxygen concentrations in DOE high-level waste tanks following loss of ventilation, and validate the model against a series of experiments

  9. Electrochemical processing of nitrate waste solutions. Phase 2, Final report

    Energy Technology Data Exchange (ETDEWEB)

    Genders, D.; Weinberg, N.; Hartsough, D. [Electrosynthesis Co., Inc., Cheektowaga, NY (US)

    1992-10-07

    The second phase of research performed at The Electrosynthesis Co., Inc. has demonstrated the successful removal of nitrite and nitrate from a synthetic effluent stream via a direct electrochemical reduction at a cathode. It was shown that direct reduction occurs at good current efficiencies in 1,000 hour studies. The membrane separation process is not readily achievable for the removal of nitrites and nitrates due to poor current efficiencies and membrane stability problems. A direct reduction process was studied at various cathode materials in a flow cell using the complete synthetic mix. Lead was found to be the cathode material of choice, displaying good current efficiencies and stability in short and long term tests under conditions of high temperature and high current density. Several anode materials were studied in both undivided and divided cell configurations. A divided cell configuration was preferable because it would prevent re-oxidation of nitrite by the anode. The technical objective of eliminating electrode fouling and solids formation was achieved although anode materials which had demonstrated good stability in short term divided cell tests corroded in 1,000 hour experiments. The cause for corrosion is thought to be F{sup {minus}} ions from the synthetic mix migrating across the cation exchange membrane and forming HF in the acid anolyte. Other possibilities for anode materials were explored. A membrane separation process was investigated which employs an anion and cation exchange membrane to remove nitrite and nitrate, recovering caustic and nitric acid. Present research has shown poor current efficiencies for nitrite and nitrate transport across the anion exchange membrane due to co-migration of hydroxide anions. Precipitates form within the anion exchange membranes which would eventually result in the failure of the membranes. Electrochemical processing offers a highly promising and viable method for the treatment of nitrate waste solutions.

  10. IMPROVING TACONITE PROCESSING PLANT EFFICIENCY BY COMPUTER SIMULATION, Final Report

    Energy Technology Data Exchange (ETDEWEB)

    William M. Bond; Salih Ersayin

    2007-03-30

    This project involved industrial scale testing of a mineral processing simulator to improve the efficiency of a taconite processing plant, namely the Minorca mine. The Concentrator Modeling Center at the Coleraine Minerals Research Laboratory, University of Minnesota Duluth, enhanced the capabilities of available software, Usim Pac, by developing mathematical models needed for accurate simulation of taconite plants. This project provided funding for this technology to prove itself in the industrial environment. As the first step, data representing existing plant conditions were collected by sampling and sample analysis. Data were then balanced and provided a basis for assessing the efficiency of individual devices and the plant, and also for performing simulations aimed at improving plant efficiency. Performance evaluation served as a guide in developing alternative process strategies for more efficient production. A large number of computer simulations were then performed to quantify the benefits and effects of implementing these alternative schemes. Modification of makeup ball size was selected as the most feasible option for the target performance improvement. This was combined with replacement of existing hydrocyclones with more efficient ones. After plant implementation of these modifications, plant sampling surveys were carried out to validate findings of the simulation-based study. Plant data showed very good agreement with the simulated data, confirming results of simulation. After the implementation of modifications in the plant, several upstream bottlenecks became visible. Despite these bottlenecks limiting full capacity, concentrator energy improvement of 7% was obtained. Further improvements in energy efficiency are expected in the near future. The success of this project demonstrated the feasibility of a simulation-based approach. Currently, the Center provides simulation-based service to all the iron ore mining companies operating in northern

  11. Partnew - New solvent extraction processes for minor actinides - final report

    International Nuclear Information System (INIS)

    Madic, C.; Testard, F.; Hudson, M.J.; Liljenzin, J.O.; Christiansen, B.; Ferrando, M.; Facchini, A.; Geist, A.; Modolo, G.; Gonzalez-Espartero, A.; Mendoza, J. de

    2004-01-01

    The objectives of the European project PARTNEW were to define solvent extraction processes for the partitioning of the minor actinides, Am and Cm, from the aqueous high active raffinate or high active concentrate issuing the reprocessing of nuclear spent fuels by the PUREX process. Eleven laboratories participated to the research: 1/ CEA-DEN (Marcoule), 2/ CEA-DSM (Saclay), 3/ UREAD (U.K.), 4/ CTU (Sweden), 5/ ITU (Germany), 6/ ENEA (Italy), 7/ PoliMi (Italy), 8/ FZK-INE (Germany), 9/ FZJ-ISR (Germany), 10/ CIEMAT (Spain) and 11/ UAM (Spain). The research was organised into eight work packages (WP): Basic and applied DIAMEX studies, using diamide extractants for the co-extraction of actinides(III) (An(III)) and lanthanides(III) (Ln(III)) nitrates (WP1 and WP2), Basic and applied SANEX studies based on the use of polydentate N-ligands for the An(III)/Ln(III) separation (WP3 and WP4), Basic and applied SANEX studies based on the use of synergistic mixtures made of bis-(chloro-phenyl)-di-thio-phosphinic acid + neutral O-bearing ligand, (WP5 and WP6), Basic SANEX studies for the An(III)/Ln(III) separation, based on the use of new S-bearing ligands, Basic and applied studies for the Am(III)/Cm(III) separation. The work done in the fundamental and applied domains was very fruitful. Several processes have been successfully tested with genuine high active raffinates and concentrate. (authors)

  12. Characterize and Model Final Waste Formulations and Offgas Solids from Thermal Treatment Processes - FY-98 Final Report for LDRD 2349

    Energy Technology Data Exchange (ETDEWEB)

    Kessinger, Glen Frank; Nelson, Lee Orville; Grandy, Jon Drue; Zuck, Larry Douglas; Kong, Peter Chuen Sun; Anderson, Gail

    1999-08-01

    The purpose of LDRD #2349, Characterize and Model Final Waste Formulations and Offgas Solids from Thermal Treatment Processes, was to develop a set of tools that would allow the user to, based on the chemical composition of a waste stream to be immobilized, predict the durability (leach behavior) of the final waste form and the phase assemblages present in the final waste form. The objectives of the project were: • investigation, testing and selection of thermochemical code • development of auxiliary thermochemical database • synthesis of materials for leach testing • collection of leach data • using leach data for leach model development • thermochemical modeling The progress toward completion of these objectives and a discussion of work that needs to be completed to arrive at a logical finishing point for this project will be presented.

  13. Host state screening process: Regional management plan: [Final report

    International Nuclear Information System (INIS)

    Drobny, N.L.

    1986-01-01

    This report discusses the procedure and cirteria that the Commission selected for designating a host state, should a state not volunteer for this role. Section 2 describes the wide range of approaches considered. Advantages and disadvantages of each are reviewed briefly, and the overall timetable established by the Commission for host state selection is presented. Section 3 describes the selected process for host state designation which involves emphasis on waste quantities generated and transportation factors. Section 4 presents relevant data on characteristics of wastes presently generated and presents estimates for future waste generation to Year 2015. Section 5 presents the results of transportation analyses considering the distance over which waste would be transported and safety (accident) statistics for waste transport routes. Section 6 integrates the conclusions from the analysis of waste volumes generated and transportation factors and suggests how these results might be used to designate a host state. 11 refs., 6 figs., 9 tabs

  14. Anion-exchange resin-based desulfurization process. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Sheth, A C; Dharmapurikar, R; Strevel, S D

    1994-01-01

    The following investigations were performed: (1) batch mode screening of eleven(11) commercially available resins and selection of three candidate resins for further evaluation in a fixed-bed setup. (2) Process variables study using three candidate resins in the fixed-bed setup and selection of the ``best`` resin for process economics development. (3) Exhaustion efficiency and solution concentration were found to be inversely related necessitating a trade-off between the resin cost versus the cost of evaporation/concentration of ensuing effluents. (4) Higher concentration of the HCO{sub 3}{sup {minus}} form of active sites over less active CO{sub 3}{sup 2{minus}} form of sites in the resin was believed to be the main reason for the observed increase in the equilibrium capacity of the resin at an elevated static CO{sub 2}-pressure. This Increase in capacity was found to level off around 80--120 psig range. The increase in CO{sub 2}-pressure, however, did not appear to affect the overall ion-exchange kinetics. (5) In the fixed-bed mode, the solution concentration was found to affect the equilibrium capacity of candidate resins. Their relationship was well satisfied by the Langmuir type non-linear equilibrium isotherm. Alternatively, the effect of solution concentration on overall ion-exchange kinetics varied from resin to resin. (6) Product inhibition effect on the resin was observed as an initial increase followed by a significant decrease in the resin`s equilibrium capacity for SO{sub 4}{sup 2{minus}} as the HCO{sub 3}{sup {minus}}/SO{sub 4}{sup 2{minus}} molar ratio in the solution was increased from 0 to 1.0. This ratio, however, did not affect the overall ion-exchange kinetics.

  15. Process Inherent Ultimate Safety (PIUS) reactor evaluation study: Final report

    International Nuclear Information System (INIS)

    1987-02-01

    This report presents the results of an independent study by United Engineers and Constructors (UNITED) of the SECURE-P Process Inherent Ultimate Safety (PIUS) Reactor Concept which is presently under development by the Swedish light water reactor vendor ASEA-ATOM of Vasteras, Sweden. This study was performed to investigate whether there is any realistic basis for believing that the PIUS reactor could be a viable competitor in the US energy market in the future. Assessments were limited to the technical, economic and licensing aspects of PIUS. Socio-political issues, while certainly important in answering this question, are so broad and elusive that it was considered that addressing them with the limited perspective of one small group from one company would be of questionable value and likely be misleading. Socio-political issues aside, the key issue is economics. For this reason, the specific objectives of this study were to determine if the estimated PIUS plant cost will be competitive in the US market and to identify and evaluate the technical and licensing risks that might make PIUS uneconomical or otherwise unacceptable

  16. Linear and Nonlinear MHD Wave Processes in Plasmas. Final Report

    International Nuclear Information System (INIS)

    Tataronis, J. A.

    2004-01-01

    This program treats theoretically low frequency linear and nonlinear wave processes in magnetized plasmas. A primary objective has been to evaluate the effectiveness of MHD waves to heat plasma and drive current in toroidal configurations. The research covers the following topics: (1) the existence and properties of the MHD continua in plasma equilibria without spatial symmetry; (2) low frequency nonresonant current drive and nonlinear Alfven wave effects; and (3) nonlinear electron acceleration by rf and random plasma waves. Results have contributed to the fundamental knowledge base of MHD activity in symmetric and asymmetric toroidal plasmas. Among the accomplishments of this research effort, the following are highlighted: Identification of the MHD continuum mode singularities in toroidal geometry. Derivation of a third order ordinary differential equation that governs nonlinear current drive in the singular layers of the Alfven continuum modes in axisymmetric toroidal geometry. Bounded solutions of this ODE implies a net average current parallel to the toroidal equilibrium magnetic field. Discovery of a new unstable continuum of the linearized MHD equation in axially periodic circular plasma cylinders with shear and incompressibility. This continuum, which we named ''accumulation continuum'' and which is related to ballooning modes, arises as discrete unstable eigenfrequency accumulate on the imaginary frequency axis in the limit of large mode numbers. Development of techniques to control nonlinear electron acceleration through the action of multiple coherent and random plasmas waves. Two important elements of this program aye student participation and student training in plasma theory

  17. Interpolation of final geometry and result fields in process parameter space

    NARCIS (Netherlands)

    Misiun, Grzegorz Stefan; Wang, Chao; Geijselaers, Hubertus J.M.; van den Boogaard, Antonius H.; Saanouni, K.

    2016-01-01

    Different routes to produce a product in a bulk forming process can be described by a limited set of process parameters. The parameters determine the final geometry as well as the distribution of state variables in the final shape. Ring rolling has been simulated using different parameter settings.

  18. The defense waste processing facility: the final processing step for defense high-level waste disposal

    International Nuclear Information System (INIS)

    Cowan, S.P.; Sprecher, W.M.; Walton, R.D.

    1983-01-01

    The policy of the U.S. Department of Energy is to pursue an aggressive and credible waste management program that advocates final disposal of government generated (defense) high-level nuclear wastes in a manner consistent with environmental, health, and safety responsibilities and requirements. The Defense Waste Processing Facility (DWPF) is an essential component of the Department's program. It is the first project undertaken in the United States to immobilize government generated high-level nuclear wastes for geologic disposal. The DWPF will be built at the Department's Savannah River Plant near Aiken, South Carolina. When construction is complete in 1989, the DWPF will begin processing the high-level waste at the Savannah River Plant into a borosilicate glass form, a highly insoluble and non-dispersable product, in easily handled canisters. The immobilized waste will be stored on site followed by transportation to and disposal in a Federal repository. The focus of this paper is on the DWPF. The paper discusses issues which justify the project, summarizes its technical attributes, analyzes relevant environmental and insitutional factors, describes the management approach followed in transforming technical and other concepts into concrete and steel, and concludes with observations about the future role of the facility

  19. A protocol for arguing about rejections in negotiation

    NARCIS (Netherlands)

    Prakken, Henry; van Veenen, J.; Parsons, S; Maudet, N; Moraitis, P; Rahwan,

    2006-01-01

    One form of argument-based negotiation is when agents argue about why an offer was rejected. If an agent can state a reason for a rejection of an offer, the negotiation process may become more efficient since the other agent can take this reason into account when making new offers. Also, if a reason

  20. Radionuclide diagnosis of allograft rejection

    International Nuclear Information System (INIS)

    George, E.A.

    1982-01-01

    Interaction with one or more anatomical and physiopathological characteristics of the rejecting renal allograft is suggested by those radioagents utilized specifically for the diagnosis of allograft rejection. Rejection, the most common cause of declining allograft function, is frequently mimicked clinically or masked by other immediate or long term post transplant complications. Understanding of the anatomical pathological features and kinetics of rejection and their modification by immunosuppressive maintenance and therapy are important for the proper clinical utilization of these radioagents. Furthermore, in selecting these radionuclides, one has to consider the comparative availability, preparatory and procedural simplicity, acquisition and display techniques and the possibility of timely report. The clinical utilities of radiofibrinogen, /sup 99m/Tc sulfur colloid and 67 Ga in the diagnosis of allograft rejection have been evaluated to a variable extent in the past. The potential usefulness of the recently developed preparations of 111 In labeled autologous leukocytes and platelets are presently under investigation

  1. Antimyosin imaging in cardiac transplant rejection

    International Nuclear Information System (INIS)

    Johnson, L.L.; Cannon, P.J.

    1991-01-01

    Fab fragments of antibodies specific for cardiac myosin have been labeled with indium-111 and injected intravenously into animals and into patients with heart transplants. The antibodies, developed by Khaw, Haber, and co-workers, localize in cardiac myocytes that have been damaged irreversibly by ischemia, myocarditis, or the rejection process. After clearance of the labeled antibody from the cardiac blood pool, planar imaging or single photon emission computed tomography is performed. Scintigrams reveal the uptake of the labeled antimyosin in areas of myocardium undergoing transplant rejection. In animal studies, the degree of antimyosin uptake appears to correlate significantly with the degree of rejection assessed at necropsy. In patients, the correlation between scans and pathologic findings from endomyocardial biopsy is not as good, possibly because of sampling error in the endomyocardial biopsy technique. The scan results at 1 year correlate with either late complications (positive) or benign course (negative). Current limitations of the method include slow blood clearance, long half-life of indium-111, and hepatic uptake. Overcoming these limitations represents a direction for current research. It is possible that from these efforts a noninvasive approach to the diagnosis and evaluation of cardiac transplantation may evolve that will decrease the number of endomyocardial biopsies required to evaluate rejection. This would be particularly useful in infants and children. 31 references

  2. APPRAISAL OF FINAL TAILINGS APPLICABILITY FOR PROCESSING AND PRODUCTION OF MODIFIERS OF IRON-CARBON ALLOYS

    Directory of Open Access Journals (Sweden)

    A. S. Panasugin

    2011-01-01

    Full Text Available The methodology of rating of the galvanic final tailings applicability for further processing in the interests of needs of metallurgical production of the Republic Belarus is offered.

  3. Sustainable Approach for Landfill Management at Final Processing Site Cikundul in Sukabumi City, Indonesia

    OpenAIRE

    Sri Darwati

    2012-01-01

    The main problem of landfill management in Indonesia is the difficulty in getting a location for Final Processing Sites (FPS) due to limited land and high land prices. Besides, about 95% of existing landfills are uncontrolled dumping sites, which could potentially lead to water, soil and air pollution. Based on data from the Ministry of Environment (2010), The Act of the Republic of Indonesia Number 18 Year 2008 Concerning Solid Waste Management, prohibits open dumping at final processing sit...

  4. Building gene expression profile classifiers with a simple and efficient rejection option in R.

    Science.gov (United States)

    Benso, Alfredo; Di Carlo, Stefano; Politano, Gianfranco; Savino, Alessandro; Hafeezurrehman, Hafeez

    2011-01-01

    The collection of gene expression profiles from DNA microarrays and their analysis with pattern recognition algorithms is a powerful technology applied to several biological problems. Common pattern recognition systems classify samples assigning them to a set of known classes. However, in a clinical diagnostics setup, novel and unknown classes (new pathologies) may appear and one must be able to reject those samples that do not fit the trained model. The problem of implementing a rejection option in a multi-class classifier has not been widely addressed in the statistical literature. Gene expression profiles represent a critical case study since they suffer from the curse of dimensionality problem that negatively reflects on the reliability of both traditional rejection models and also more recent approaches such as one-class classifiers. This paper presents a set of empirical decision rules that can be used to implement a rejection option in a set of multi-class classifiers widely used for the analysis of gene expression profiles. In particular, we focus on the classifiers implemented in the R Language and Environment for Statistical Computing (R for short in the remaining of this paper). The main contribution of the proposed rules is their simplicity, which enables an easy integration with available data analysis environments. Since in the definition of a rejection model tuning of the involved parameters is often a complex and delicate task, in this paper we exploit an evolutionary strategy to automate this process. This allows the final user to maximize the rejection accuracy with minimum manual intervention. This paper shows how the use of simple decision rules can be used to help the use of complex machine learning algorithms in real experimental setups. The proposed approach is almost completely automated and therefore a good candidate for being integrated in data analysis flows in labs where the machine learning expertise required to tune traditional

  5. Non-clairvoyant weighted flow time scheduling with rejection penalty

    DEFF Research Database (Denmark)

    Chan, Ho-Leung; Chan, Sze-Hang; Lam, Tak-Wah

    2012-01-01

    is defined as the weighted flow time of the job plus the penalty if it is rejected before completion. Previous work on minimizing the total user cost focused on the clairvoyant single-processor setting [BBC+03,CLL11] and has produced O(1)-competitive online algorithm for jobs with arbitrary weights...... algorithm has to decide job rejection and determine the order and speed of job execution. It is interesting to study the tradeoff between the above-mentioned user cost and energy. This paper gives two O(1)-competitive non-clairvoyant algorithms for minimizing the user cost plus energy on a single processor......This paper initiates the study of online scheduling with rejection penalty in the non-clairvoyant setting, i.e., the size (processing time) of a job is not assumed to be known at its release time. In the rejection penalty model, jobs can be rejected with a penalty, and the user cost of a job...

  6. A technetium rejection flowsheet

    International Nuclear Information System (INIS)

    Baker, R.; Miles, J.H.; Roberts, P.T.

    1990-01-01

    A single contactor unit has been designed which enables Tc to be removed from a TBP/diluent stream bearing U and Pu, by means of a 5M HNO 3 wash. A Tc waste stream is produced which is virtually free from U and Pu. The flowsheet has been tested firstly with U and Tc, then with U, Pu and Tc, and finally in a highly active facility with real PWR fuel solution. About 97% of the Tc was removed from the organic phase and U and Pu levels in the Tc waste have usually been below 0.04% of those in the product stream. (author)

  7. Heterosexual Rejection and Mate Choice: A Sociometer Perspective

    Directory of Open Access Journals (Sweden)

    Lin eZHANG

    2015-12-01

    Full Text Available Previous studies about the effects of social rejection on individuals’ social behaviors have produced mixed results and tend to study mating behaviors from a static point of view. However, mate selection in essence is a dynamic process, and therefore sociometer theory opens up a new perspective for studying mating and its underlying practices. Based on this theory and using self-perceived mate value in the relationship between heterosexual rejection and mate choice as a mediating role, this current study examined the effects of heterosexual rejection on mate choice in two experiments. Results showed that heterosexual rejection significantly reduced self-perceived mate value, expectation, and behavioral tendencies, while heterosexual acceptance indistinctively increased these measures. Self-perceived mate value did not serve as a mediator in the relationship between heterosexual rejection and mate expectation, but it mediated the relationship between heterosexual rejection and mating behavior tendencies towards potential objects. Moreover, individuals evaded both rejection and irrelevant people when suffering from rejection.

  8. Active disturbance rejection controller for chemical reactor

    International Nuclear Information System (INIS)

    Both, Roxana; Dulf, Eva H.; Muresan, Cristina I.

    2015-01-01

    In the petrochemical industry, the synthesis of 2 ethyl-hexanol-oxo-alcohols (plasticizers alcohol) is of high importance, being achieved through hydrogenation of 2 ethyl-hexenal inside catalytic trickle bed three-phase reactors. For this type of processes the use of advanced control strategies is suitable due to their nonlinear behavior and extreme sensitivity to load changes and other disturbances. Due to the complexity of the mathematical model an approach was to use a simple linear model of the process in combination with an advanced control algorithm which takes into account the model uncertainties, the disturbances and command signal limitations like robust control. However the resulting controller is complex, involving cost effective hardware. This paper proposes a simple integer-order control scheme using a linear model of the process, based on active disturbance rejection method. By treating the model dynamics as a common disturbance and actively rejecting it, active disturbance rejection control (ADRC) can achieve the desired response. Simulation results are provided to demonstrate the effectiveness of the proposed method

  9. Active disturbance rejection controller for chemical reactor

    Energy Technology Data Exchange (ETDEWEB)

    Both, Roxana; Dulf, Eva H.; Muresan, Cristina I., E-mail: roxana.both@aut.utcluj.ro [Technical University of Cluj-Napoca, 400114 Cluj-Napoca (Romania)

    2015-03-10

    In the petrochemical industry, the synthesis of 2 ethyl-hexanol-oxo-alcohols (plasticizers alcohol) is of high importance, being achieved through hydrogenation of 2 ethyl-hexenal inside catalytic trickle bed three-phase reactors. For this type of processes the use of advanced control strategies is suitable due to their nonlinear behavior and extreme sensitivity to load changes and other disturbances. Due to the complexity of the mathematical model an approach was to use a simple linear model of the process in combination with an advanced control algorithm which takes into account the model uncertainties, the disturbances and command signal limitations like robust control. However the resulting controller is complex, involving cost effective hardware. This paper proposes a simple integer-order control scheme using a linear model of the process, based on active disturbance rejection method. By treating the model dynamics as a common disturbance and actively rejecting it, active disturbance rejection control (ADRC) can achieve the desired response. Simulation results are provided to demonstrate the effectiveness of the proposed method.

  10. Appearance-based rejection sensitivity: implications for mental and physical health, affect, and motivation.

    Science.gov (United States)

    Park, Lora E

    2007-04-01

    Appearance-Based Rejection Sensitivity (Appearance-RS) is a personality-processing system characterized by anxious concerns and expectations about being rejected based on one's physical attractiveness. People differ in their sensitivity to rejection based on appearance, with consequences for mental and physical health, self-esteem, affect, and feelings of belonging. Study 1 describes the development and validation of the Appearance-RS scale, its relation to personality variables and to health-related outcomes. Study 2 provides experimental evidence that high Appearance-RS people feel more alone and rejected when asked to think about negative aspects of their appearance. Finally, Study 3 tests ways to reduce the negative effects of receiving an appearance threat among high Appearance-RS participants. Specifically, high Appearance-RS participants who engaged in self-affirmation (thought of their personal strengths) or received a secure attachment prime (thought of a close, caring relationship) were buffered from the negative effects of an appearance threat on subsequent state self-esteem and mood.

  11. Rejection of micropollutants by clean and fouled forward osmosis membrane

    KAUST Repository

    Valladares Linares, Rodrigo

    2011-12-01

    As forward osmosis (FO) gains attention as an efficient technology to improve wastewater reclamation processes, it is fundamental to determine the influence of fouling in the rejection of emerging contaminants (micropollutants). This study focuses on the rejection of 13 selected micropollutants, spiked in a secondary wastewater effluent, by a FO membrane, using Red Sea water as draw solution (DS), differentiating the effects on the rejection caused by a clean and fouled membrane. The resulting effluent was then desalinated at low pressure with a reverse osmosis (RO) membrane, to produce a high quality permeate and determine the rejection with a coupled forward osmosis - low pressure reverse osmosis (FO-LPRO) system. When considering only FO with a clean membrane, the rejection of the hydrophilic neutral compounds was between 48.6% and 84.7%, for the hydrophobic neutrals the rejection ranged from 40.0% to 87.5%, and for the ionic compounds the rejections were between 92.9% and 96.5%. With a fouled membrane, the rejections were between 44.6% and 95.2%, 48.7%-91.5% and 96.9%-98.6%, respectively. These results suggest that, except for the hydrophilic neutral compounds, the rejection of the micropollutants is increased by the presence of a fouling layer, possibly due to the higher hydrophilicity of the FO fouled membrane compared to the clean one, the increased adsorption capacity of hydrophilic compounds and reduced mass transport capacity, membrane swelling, and the higher negative charge of the membrane surface, related to the foulants composition, mainly NOM acids (carboxylic radicals) and polysaccharides or polysaccharide-like substances. However, when coupled with RO, the rejections in both cases increased above 96%. The coupled FO-LPRO system was an effective double barrier against the selected micropollutants. © 2011 Elsevier Ltd.

  12. Rejection of micropollutants by clean and fouled forward osmosis membrane

    KAUST Repository

    Valladares Linares, Rodrigo; Yangali-Quintanilla, Victor; Li, Zhenyu; Amy, Gary L.

    2011-01-01

    As forward osmosis (FO) gains attention as an efficient technology to improve wastewater reclamation processes, it is fundamental to determine the influence of fouling in the rejection of emerging contaminants (micropollutants). This study focuses on the rejection of 13 selected micropollutants, spiked in a secondary wastewater effluent, by a FO membrane, using Red Sea water as draw solution (DS), differentiating the effects on the rejection caused by a clean and fouled membrane. The resulting effluent was then desalinated at low pressure with a reverse osmosis (RO) membrane, to produce a high quality permeate and determine the rejection with a coupled forward osmosis - low pressure reverse osmosis (FO-LPRO) system. When considering only FO with a clean membrane, the rejection of the hydrophilic neutral compounds was between 48.6% and 84.7%, for the hydrophobic neutrals the rejection ranged from 40.0% to 87.5%, and for the ionic compounds the rejections were between 92.9% and 96.5%. With a fouled membrane, the rejections were between 44.6% and 95.2%, 48.7%-91.5% and 96.9%-98.6%, respectively. These results suggest that, except for the hydrophilic neutral compounds, the rejection of the micropollutants is increased by the presence of a fouling layer, possibly due to the higher hydrophilicity of the FO fouled membrane compared to the clean one, the increased adsorption capacity of hydrophilic compounds and reduced mass transport capacity, membrane swelling, and the higher negative charge of the membrane surface, related to the foulants composition, mainly NOM acids (carboxylic radicals) and polysaccharides or polysaccharide-like substances. However, when coupled with RO, the rejections in both cases increased above 96%. The coupled FO-LPRO system was an effective double barrier against the selected micropollutants. © 2011 Elsevier Ltd.

  13. Materials, process, product analysis of coal process technology. Phase I final report

    Energy Technology Data Exchange (ETDEWEB)

    Saxton, J. C.; Roig, R. W.; Loridan, A.; Leggett, N. E.; Capell, R. G.; Humpstone, C. C.; Mudry, R. N.; Ayres, E.

    1976-02-01

    The purpose of materials-process-product analysis is a systematic evaluation of alternative manufacturing processes--in this case processes for converting coal into energy and material products that can supplement or replace petroleum-based products. The methodological steps in the analysis include: Definition of functional operations that enter into coal conversion processes, and modeling of alternative, competing methods to accomplish these functions; compilation of all feasible conversion processes that can be assembled from combinations of competing methods for the functional operations; systematic, iterative evaluation of all feasible conversion processes under a variety of economic situations, environmental constraints, and projected technological advances; and aggregative assessments (economic and environmental) of various industrial development scenarios. An integral part of the present project is additional development of the existing computer model to include: A data base for coal-related materials and coal conversion processes; and an algorithmic structure that facilitates the iterative, systematic evaluations in response to exogenously specified variables, such as tax policy, environmental limitations, and changes in process technology and costs. As an analytical tool, the analysis is intended to satisfy the needs of an analyst working at the process selection level, for example, with respect to the allocation of RDandD funds to competing technologies.

  14. Donor-specific rejection: Clinical and scan correlation

    International Nuclear Information System (INIS)

    Wilson, M.A.; Mehta, R.C.; Perlman, S.B.; Servilla, K.; Sollinger, H.W.; Deierhoi, M.H.; Belzer, F.O.

    1986-01-01

    All 470 scans on 132 consecutive renal transplantation patients were reviewed. Scan patterns identified included acute tubular necrosis and conventional rejection. A new pattern, donor specific rejection (DSR), was identified in 24 of 42 patients on the living related donor specific transfusion (DST) protocol. This was characterized by good perfusion and extraction but significant renal stasis of tracer. This pattern was unique to the DST recipients and improved with antirejection therapy. The clinical features (incidence, temporal onset) and severity (duration, serum creatinines) are compared in these patient populations. DSR occurs more frequently than conventional rejection but is a milder process

  15. Laughter as a social rejection cue: Influence of prior explicit experience of social rejection on cardiac signs of "freezing".

    Science.gov (United States)

    Lackner, Helmut K; Reiter-Scheidl, Katharina; Aydin, Nilüfer; Perchtold, Corinna M; Weiss, Elisabeth M; Papousek, Ilona

    2018-06-01

    The study aimed at investigating the immediate cardiac effect of the sudden perception of other people's laughter after experimentally manipulating healthy participants' proneness to experience laughter as a cue of social threat. We expected that participants would show cardiac signs of freezing (i.e., sustained heart rate deceleration immediately after perception of the laughter) after prior social rejection but not or less so after prior acceptance, due to an increased bias to perceive the ambiguous social signal as a cue of social threat and rejection after rejection had been primed. Contrary to expectations, the perception of other people's laughter elicited a decelerative (freezing) response regardless of whether it was preceded by the experience of social rejection or acceptance. The response was prolonged in participants who had been accepted beforehand compared to those who had been rejected. The findings indicate that, given a relevant social context, other people's laughter can be a powerful cue of social threat and rejection also in healthy individuals. Prolonged heart rate deceleration after an ambiguous social signal may facilitate the processing of significant social information in the socially threatening situation. The study adds to the literature rendering the course of the immediate transient heart rate response a useful tool in social rejection research. Additionally, the findings suggested that in some cases the further progress of transient heart rate changes in more extended time-windows (about 30 s) may provide additional relevant information about the processing of social cues. Copyright © 2018 Elsevier B.V. All rights reserved.

  16. Evaluation, engineering and development of advanced cyclone processes. Final separating media evaluation and test report (FSMER)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-19

    {open_quotes}Evaluation Engineering and Development of Advanced Cyclone Processes{close_quotes} is one of the DOE-PETC sponsored advanced coal cleaning projects, which share a number of specific goals. These goals are to produce a 6% ash product, reject 85% of the parent coal`s pyritic sulfur, recover 85% of the parent coal`s Btu value, and provide products that are less than 30% moisture. The process in this project, as the name implies, relies on a cyclone or cyclonic separator to achieve physical beneficiation based on the gravimetric differences between clean coal and its impurities. Just as important as the cyclonic separator, if not more so, is the selection of a parting liquid or medium for use in the separator. Selection of a separating medium is regarded as a significant portion of the project because it has a profound impact on the required unit operations, the performance of the separator, and economics of the process. The choice of medium especially influences selection of media recovery system(s), and the characteristics of clean coal and refuse products. Since medium selection is such an important aspect of the project, portions of the project are dedicated to the study, evaluation, and selection of the most desirable medium. Though separators are an important component, this project initially focused on media study, rather than the separators themselves. In coal processing, discussion of media requires description of the handling and recovery system(s), separation performance, interaction with coal, cost, and health, environmental and safety issues. In order to be effective, a candidate must perform well in all of these categories.

  17. Multi-objective ACO algorithms to minimise the makespan and the total rejection cost on BPMs with arbitrary job weights

    Science.gov (United States)

    Jia, Zhao-hong; Pei, Ming-li; Leung, Joseph Y.-T.

    2017-12-01

    In this paper, we investigate the batch-scheduling problem with rejection on parallel machines with non-identical job sizes and arbitrary job-rejected weights. If a job is rejected, the corresponding penalty has to be paid. Our objective is to minimise the makespan of the processed jobs and the total rejection cost of the rejected jobs. Based on the selected multi-objective optimisation approaches, two problems, P1 and P2, are considered. In P1, the two objectives are linearly combined into one single objective. In P2, the two objectives are simultaneously minimised and the Pareto non-dominated solution set is to be found. Based on the ant colony optimisation (ACO), two algorithms, called LACO and PACO, are proposed to address the two problems, respectively. Two different objective-oriented pheromone matrices and heuristic information are designed. Additionally, a local optimisation algorithm is adopted to improve the solution quality. Finally, simulated experiments are conducted, and the comparative results verify the effectiveness and efficiency of the proposed algorithms, especially on large-scale instances.

  18. Optimizing the air flotation water treatment process. Final report, May 1997

    Energy Technology Data Exchange (ETDEWEB)

    Barnett, B.

    1998-09-01

    The injection water for the Nelson Project is a combination of produced and make-up water, typical of many Eastern Kansas operations. The make-up water is a low-salinity salt water from the Arbuckle Formation and contains dissolved minerals and sulfides. The produced water contains suspended oil, suspended clay and silt particles, along with a combination of other dissolved minerals. The combination of the two waters causes several undesirable reactions. The suspended solids load contained in the combined waters would plug a 75-micron plant bag filter within one day. Wellhead filters of 75-micron size were also being used on the injection wells. The poor water quality resulted in severe loss of injectivity and frequent wellbore cleaning of the injection wells. Various mechanical and graded-bed filtration methods were considered for cleaning the water. These methods were rejected due to the lack of field equipment and service availability. A number of vendors did not even respond to the author`s request. The air flotation process was selected as offering the best hope for a long-term solution. The objective of this work is to: increase the cost effectiveness of the process through optimizing process design factors and operational parameters. A vastly modified air flotation system is the principal tool for accomplishing the project objective. The air flotation unit, as received from manufacturer Separation Specialist, was primarily designed to remove oil from produced water. The additional requirement for solids removal necessitated major physical changes in the unit. Problems encountered with the air flotation unit and specific modifications are detailed in the body of the report.

  19. Thin film silicon solar cells: advanced processing and characterization - Final report

    Energy Technology Data Exchange (ETDEWEB)

    Ballif, Ch.

    2008-04-15

    This final report elaborated for the Swiss Federal Office of Energy (SFOE) takes a look at the results of a project carried out at the photovoltaics laboratory at the University of Neuchatel in Switzerland. The project aimed to demonstrate the production of high-efficiency thin-film silicon devices on flexible substrates using low cost processes. New ways of improving processing and characterisation are examined. The process and manufacturing know-how necessary to provide support for industrial partners within the framework of further projects is discussed. The authors state that the efficiency of most devices was significantly improved, both on glass substrates and on flexible plastic foils. The process reproducibility was also improved and the interactions between the different layers in the device are now said to be better understood. The report presents the results obtained and discusses substrate materials, transparent conductors, defect analyses and new characterisation tools. Finally, the laboratory infrastructure is described.

  20. Coherent control of photoabsorption processes and calculation of nonlinear optical processes. Final technical report

    International Nuclear Information System (INIS)

    Lambropoulos, P.

    1998-01-01

    The work on the grant for the entire period of its duration concentrated on two different but related areas, namely coherent control of photoabsorption processes and the calculation of non linear optical processes with short wavelength radiation. On the first topic, the work dealt with the problem of controlling the population transfer from one to another bound state of a system in a route that passes through a continuum. This question is most important in the context of transferring populations between vibrational states of a molecule through a sequence of two pulses taking the system via the dissociation continuum. On the second topic, their work was motivated by the availability of XUV and soft X-ray coherent radiation sources obtained through high order harmonic generation. In addition, a few other techniques based on schemes of photo-pumped X-ray lasers promise to provide in the near-future similarly coherent sources. It is thus important to have an assessment of the possibility of extending non-linear optical processes to this range of wavelengths. This means assessing the relevant magnitude of the susceptibilities for third harmonic generation, stimulated Raman scattering, two-photon absorption, etc

  1. Estimating the transmission potential of supercritical processes based on the final size distribution of minor outbreaks.

    Science.gov (United States)

    Nishiura, Hiroshi; Yan, Ping; Sleeman, Candace K; Mode, Charles J

    2012-02-07

    Use of the final size distribution of minor outbreaks for the estimation of the reproduction numbers of supercritical epidemic processes has yet to be considered. We used a branching process model to derive the final size distribution of minor outbreaks, assuming a reproduction number above unity, and applying the method to final size data for pneumonic plague. Pneumonic plague is a rare disease with only one documented major epidemic in a spatially limited setting. Because the final size distribution of a minor outbreak needs to be normalized by the probability of extinction, we assume that the dispersion parameter (k) of the negative-binomial offspring distribution is known, and examine the sensitivity of the reproduction number to variation in dispersion. Assuming a geometric offspring distribution with k=1, the reproduction number was estimated at 1.16 (95% confidence interval: 0.97-1.38). When less dispersed with k=2, the maximum likelihood estimate of the reproduction number was 1.14. These estimates agreed with those published from transmission network analysis, indicating that the human-to-human transmission potential of the pneumonic plague is not very high. Given only minor outbreaks, transmission potential is not sufficiently assessed by directly counting the number of offspring. Since the absence of a major epidemic does not guarantee a subcritical process, the proposed method allows us to conservatively regard epidemic data from minor outbreaks as supercritical, and yield estimates of threshold values above unity. Crown Copyright © 2011. Published by Elsevier Ltd. All rights reserved.

  2. Computer simulation of transitional process to the final stable Brayton cycle in magnetic refrigeration

    International Nuclear Information System (INIS)

    Numasawa, T.; Hashimoto, T.

    1981-01-01

    The final working cycle in the magnetic refrigeration largely depends on the heat transfer coefficient β in the system, the parameter γ of the heat inflow from the outer system to this cycle and the period tau of the cycle. Therefore, so as to make clear this dependence, the time variation of the Brayton cycle with β, γ and tau has been investigated. In the present paper the transitional process of this cycle and the dependence of the final cooling temperature of the heat load on β, γ and tau have all been shown. (orig.)

  3. The Neural Basis of Recollection Rejection: Increases in Hippocampal-Prefrontal Connectivity in the Absence of a Shared Recall-to-Reject and Target Recollection Network.

    Science.gov (United States)

    Bowman, Caitlin R; Dennis, Nancy A

    2016-08-01

    Recollection rejection or "recall-to-reject" is a mechanism that has been posited to help maintain accurate memory by preventing the occurrence of false memories. Recollection rejection occurs when the presentation of a new item during recognition triggers recall of an associated target, a mismatch in features between the new and old items is registered, and the lure is correctly rejected. Critically, this characterization of recollection rejection involves a recall signal that is conceptually similar to recollection as elicited by a target. However, previous neuroimaging studies have not evaluated the extent to which recollection rejection and target recollection rely on a common neural signal but have instead focused on recollection rejection as a postretrieval monitoring process. This study utilized a false memory paradigm in conjunction with an adapted remember-know-new response paradigm that separated "new" responses based on recollection rejection from those that were based on a lack of familiarity with the item. This procedure allowed for parallel recollection rejection and target recollection contrasts to be computed. Results revealed that, contrary to predictions from theoretical and behavioral literature, there was virtually no evidence of a common retrieval mechanism supporting recollection rejection and target recollection. Instead of the typical target recollection network, recollection rejection recruited a network of lateral prefrontal and bilateral parietal regions that is consistent with the retrieval monitoring network identified in previous neuroimaging studies of recollection rejection. However, a functional connectivity analysis revealed a component of the frontoparietal rejection network that showed increased coupling with the right hippocampus during recollection rejection responses. As such, we demonstrate a possible link between PFC monitoring network and basic retrieval mechanisms within the hippocampus that was not revealed with

  4. Outside advantage: can social rejection fuel creative thought?

    Science.gov (United States)

    Kim, Sharon H; Vincent, Lynne C; Goncalo, Jack A

    2013-08-01

    Eminently creative people working in fields as disparate as physics and literature refer to the experience of social rejection as fuel for creativity. Yet, the evidence of this relationship is anecdotal, and the psychological process that might explain it is as yet unknown. We theorize that the experience of social rejection may indeed stimulate creativity but only for individuals with an independent self-concept. In 3 studies, we show that individuals who hold an independent self-concept performed more creatively after social rejection relative to inclusion. We also show that this boost in creativity is mediated by a differentiation mind-set, or salient feelings of being different from others. Future research might investigate how the self-concept--for example, various cultural orientations-may shape responses to social rejection by mitigating some of the negative consequences of exclusion and potentially even motivating creative exploration. PsycINFO Database Record (c) 2013 APA, all rights reserved.

  5. Brain Region-Dependent Rejection of Neural Precursor Cell Transplants

    Directory of Open Access Journals (Sweden)

    Nina Fainstein

    2018-04-01

    Full Text Available The concept of CNS as an immune-privileged site has been challenged by the occurrence of immune surveillance and allogeneic graft rejection in the brain. Here we examined whether the immune response to allogeneic neural grafts is determined by the site of implantation in the CNS. Dramatic regional differences were observed between immune responses to allogeneic neural precursor/stem cell (NPC grafts in the striatum vs. the hippocampus. Striatal grafts were heavily infiltrated with IBA-1+ microglia/macrophages and CD3+ T cells and completely rejected. In contrast, hippocampal grafts exhibited milder IBA-1+ cell infiltration, were not penetrated efficiently by CD3+ cells, and survived efficiently for at least 2 months. To evaluate whether the hippocampal protective effect is universal, astrocytes were then transplanted. Allogeneic astrocyte grafts elicited a vigorous rejection process from the hippocampus. CD200, a major immune-inhibitory signal, plays an important role in protecting grafts from rejection. Indeed, CD200 knock out NPC grafts were rejected more efficiently than wild type NPCs from the striatum. However, lack of CD200 expression did not elicit NPC graft rejection from the hippocampus. In conclusion, the hippocampus has partial immune-privilege properties that are restricted to NPCs and are CD200-independent. The unique hippocampal milieu may be protective for allogeneic NPC grafts, through host-graft interactions enabling sustained immune-regulatory properties of transplanted NPCs. These findings have implications for providing adequate immunosuppression in clinical translation of cell therapy.

  6. Social Causes and Consequences of Rejection Sensitivity

    Science.gov (United States)

    London, Bonita; Downey, Geraldine; Bonica, Cheryl; Paltin, Iris

    2007-01-01

    Predictions from the Rejection Sensitivity (RS) model concerning the social causes and consequences of RS were examined in a longitudinal study of 150 middle school students. Peer nominations of rejection, self-report measures of anxious and angry rejection expectations, and social anxiety, social withdrawal, and loneliness were assessed at two…

  7. 7 CFR 58.136 - Rejected milk.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Rejected milk. 58.136 Section 58.136 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Milk § 58.136 Rejected milk. A plant shall reject specific milk from a producer if the milk fails to...

  8. Peer Group Rejection and Children's Outgroup Prejudice

    Science.gov (United States)

    Nesdale, Drew; Durkin, Kevin; Maass, Anne; Kiesner, Jeff; Griffiths, Judith; Daly, Josh; McKenzie, David

    2010-01-01

    Two simulation studies examined the effect of peer group rejection on 7 and 9 year old children's outgroup prejudice. In Study 1, children (n = 88) pretended that they were accepted or rejected by their assigned group, prior to competing with a lower status outgroup. Results indicated that rejected versus accepted children showed increased…

  9. Development of an advanced continuous mild gasification process for the production of coproducts. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Merriam, N.W.; Jha, M.C.

    1991-11-01

    This report is a final brief summary of development of a mild-gasification and char conversion process. Morgantown Energy Technology Center developed a concept called mild gasification. In this concept, devolatilization of coal under nonoxidizing and relatively mild temperature and pressure conditions can yield three marketable products: (1) a high-heating-value gas, (2) a high-aromatic coal liquid, and (3) a high-carbon char. The objective of this program is to develop an advanced, continuous, mild-gasification process to produce products that will make the concept economically and environmentally viable. (VC)

  10. Heat transfer enhanced microwave process for stabilization of liquid radioactive waste slurry. Final report

    International Nuclear Information System (INIS)

    White, T.L.

    1995-01-01

    The objectve of this CRADA is to combine a polymer process for encapsulation of liquid radioactive waste slurry developed by Monolith Technology, Inc. (MTI), with an in-drum microwave process for drying radioactive wastes developed by Oak Ridge National Laboratory (ORNL), for the purpose of achieving a fast, cost-effectve commercial process for solidification of liquid radioactive waste slurry. Tests performed so far show a four-fold increase in process throughput due to the direct microwave heating of the polymer/slurry mixture, compared to conventional edge-heating of the mixer. We measured a steady-state throughput of 33 ml/min for 1.4 kW of absorbed microwave power. The final waste form is a solid monolith with no free liquids and no free particulates

  11. Using Compton scattering for random coincidence rejection

    International Nuclear Information System (INIS)

    Kolstein, M.; Chmeissani, M.

    2016-01-01

    The Voxel Imaging PET (VIP) project presents a new approach for the design of nuclear medicine imaging devices by using highly segmented pixel CdTe sensors. CdTe detectors can achieve an energy resolution of ≈ 1% FWHM at 511 keV and can be easily segmented into submillimeter sized voxels for optimal spatial resolution. These features help in rejecting a large part of the scattered events from the PET coincidence sample in order to obtain high quality images. Another contribution to the background are random events, i.e., hits caused by two independent gammas without a common origin. Given that 60% of 511 keV photons undergo Compton scattering in CdTe (i.e. 84% of all coincidence events have at least one Compton scattering gamma), we present a simulation study on the possibility to use the Compton scattering information of at least one of the coincident gammas within the detector to reject random coincidences. The idea uses the fact that if a gamma undergoes Compton scattering in the detector, it will cause two hits in the pixel detectors. The first hit corresponds to the Compton scattering process. The second hit shall correspond to the photoelectric absorption of the remaining energy of the gamma. With the energy deposition of the first hit, one can calculate the Compton scattering angle. By measuring the hit location of the coincident gamma, we can construct the geometric angle, under the assumption that both gammas come from the same origin. Using the difference between the Compton scattering angle and the geometric angle, random events can be rejected.

  12. Rejection index for pressure tubes

    International Nuclear Information System (INIS)

    Mitchell, A.B.; Meneley, D.

    1989-10-01

    The objective of the present study was to establish a set of criteria (or Rejection Index) which could be used to decide whether a zirconium-2 1/2 w/o niobium pressure tube in a CANDU reactor should be removed from service due to in-service degradation. A critique of key issues associated with establishing a realistic rejection index was prepared. Areas of uncertainty in available information were identified and recommendations for further analysis and laboratory testing made. A Rejection Index based on the following limits has been recommended: 1) Limits related to design intent and normal operation: any garter spring must remain within the tolerance band specified for its design location; the annulus gas system must normally be operated in a circulating mode with a procedure in place for purging to prevent accumulation of deuterium. It must remain sensitive to leaks into any part of the systems; and pressure tube dimensions and distortions must be limited to maintain the fuel channels within the original design intent; 2) Limits related to defect tolerance: adequate time margins between occurrence of a leaking crack and unstable failure must be demonstrated for all fuel channels; long lap-type flaws are unacceptable; crack-like defects of any size are unacceptable; and score marks, frat marks and other defects with contoured profiles must fall below certain depth, length and stress intensity limits; and 3) Limits related to property degradation: at operating temperature each pressure tube must be demonstrated to have a critical length in excess of a stipulated value; the maximum equivalent hydrogen level in any pressure tube should not exceed a limit which should be defined taking into account the known history of that tube; the maximum equivalent hydrogen level in any rolled joint should not exceed a limit which is presently recommended as 200 ppm equivalent hydrogen; and the maximum diametral creep strain should be limited to less than 5%

  13. Final audit report of remedial action construction at the UMTRA Project, Grand Junction, Colorado, processing site

    International Nuclear Information System (INIS)

    1995-02-01

    This final audit report (FAR) for remedial action at the Grand Junction, Colorado, Uranium Mill Tailings Remedial Action (UMTRA) Project processing site consists of a summary of the radiological surveillances/ audits, the quality assurance (QA) in-process surveillances, and the QA final close-out inspection performed by the US Department of Energy (DOE) and Technical Assistance Contractor (TAC). The FAR also summarizes other surveillances performed by the US Nuclear Regulatory Commission (NRC). To summarize, a total of one finding and 127 observations were noted during DOE/TAC audit and surveillance activities. The NRC noted general site-related observations during the OSCRs. Follow-up to responses required from MK-Ferguson for the DOE/TAC finding and observations indicated that all issues related to the Grand Junction processing site were resolved and closed out to the DOE's satisfaction. The NRC OSCRs resulted in no issues related to the Grand Junction processing site requiring a response from MK-Ferguson

  14. Full scale application of the autotrophic denitrification in trickling filters for treatment of rejection water with high ammonia concentrations from sludge dewatering. Final report; Untersuchungen zur autotrophen Stickstoffentfernung aus ammoniumreichem Filtratwasser der Schlammentwaesserung mit grosstechnischer Realisierung in Tropfkoerpern. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Neumueller, B.; Metzger, J.W.; Pinnekamp, J.

    2003-07-01

    At many municipal wastewater treatment plants a considerable fraction of nitrogen is recirculated from the anaerobic sludge dewatering. This amounts up to 20% of the total influent nitrogen load of the wastewater treatment plant. The separate treatment of this sludge liquor creates new capacities for the treatment plant and improves effluent quality. A new process for treatment of this sludge liquor with ammonium-nitrogen concentrations above 600 mg/l is the autotrophic denitrification after partial nitritation. At the University of Stuttgart the first semi-technical trickling filter plant was built by which autotrophic denitrification was achieved. At the wastewater treatment plant of Sindelfingen the first full-scale implementation of the autotrophic denitrification in trickling filters has been designed and built. In a first trickling filter 60% of ammonia is transformed to nitrite. The investigations showed, that a few mg/l of free ammonia in this trickling filter were sufficient to inhibit the nitratation but not the nitritation. To achieve this, operating conditions as pH and temperature are of great importance. The concentration of free ammonia should be kept constant because there is an adaption of the microorganisms to free ammonia. After a decrease of the free ammonia concentration the inhibition of the nitratation declines. By thermally killing the biomass and restarting the process, can guarantee a total inhibition of the nitratation, while the concentration of free ammonia is low. In the second, closed trickling filter (anoxic conditions) ammonium is converted autotrophically to nitrogen with nitrite as electron acceptor. It was possible to set up the anoxic ammonium oxidation in full scale without inoculating the process. The very slow growth of the anammox-bacteria leads to a long adaptation phase of the process. All operating conditions such as anoxic conditions, high temperature and a concentration of nitrite below 70 mg/l have to be observed

  15. Graft rejection by cytolytic T cells. Specificity of the effector mechanism in the rejection of allogeneic marrow

    International Nuclear Information System (INIS)

    Nakamura, H.; Gress, R.E.

    1990-01-01

    Cellular effector mechanisms of allograft rejection remain incompletely described. Characterizing the rejection of foreign-marrow allografts rather than solid-organ grafts has the advantage that the cellular composition of the marrow graft, as a single cell suspension, can be altered to include cellular components with differing antigen expression. Rejection of marrow grafts is sensitive to lethal doses of radiation in the mouse but resistant to sublethal levels of radiation. In an effort to identify cells mediating host resistance, lymphocytes were isolated and cloned from spleens of mice 7 days after sublethal TBI (650 cGy) and inoculation with allogeneic marrow. All clones isolated were cytolytic with specificity for MHC encoded gene products of the allogeneic marrow donor. When cloned cells were transferred in vivo into lethally irradiated (1025 cGy) recipients unable to reject allogeneic marrow, results utilizing splenic 125IUdR uptake indicated that these MHC-specific cytotoxic clones could suppress marrow proliferation. In order to characterize the effector mechanism and the ability of the clones to affect final engraftment, double donor chimeras were constructed so that 2 target cell populations differing at the MHC from each other and from the host were present in the same marrow allograft. Results directly demonstrated an ability of CTL of host MHC type to mediate graft rejection and characterized the effector mechanism as one with specificity for MHC gene products

  16. How does sustainability certification affect the design process? Mapping final design projects at an architectural office

    DEFF Research Database (Denmark)

    Landgren, Mathilde; Jensen, Lotte Bjerregaard

    2017-01-01

    process and informing the industry of them. This has led to optimised design processes such as Integrated Energy Design, in which many decisions related to energy consumption and indoor climate are made in the early design stages. The current tendency is to use an expanded notion of sustainability......, derived from the sustainability certification system itself, and to apply it even in the early design process. This perspective emphasises all phases of the life cycle of a building. The goal of the present study was to map how a Danish architectural office approached sustainability in the projects......The context of the study is the very strict regulation of energy consumption for operating buildings in Denmark. It is difficult to meet the requirements by system optimisation in the final design phase, so recent research has focused on ways of meeting the target by adapting the whole design...

  17. The Theory of High Energy Collision Processes - Final Report DOE/ER/40158-1

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Tai, T.

    2011-09-15

    In 1984, DOE awarded Harvard University a new Grant DE-FG02-84ER40158 to continue their support of Tai Tsun Wu as Principal Investigator of research on the theory of high energy collision processes. This Grant was renewed and remained active continuously from June 1, 1984 through November 30, 2007. Topics of interest during the 23-year duration of this Grant include: the theory and phenomenology of collision and production processes at ever higher energies; helicity methods of QED and QCD; neutrino oscillations and masses; Yang-Mills gauge theory; Beamstrahlung; Fermi pseudopotentials; magnetic monopoles and dyons; cosmology; classical confinement; mass relations; Bose-Einstein condensation; and large-momentum-transfer scattering processes. This Final Report describes the research carried out on Grant DE-FG02-84ER40158 for the period June 1, 1984 through November 30, 2007. Two books resulted from this project and a total of 125 publications.

  18. Final disposal of spent nuclear fuel - regulatory system and roles of different actors during the decision process

    International Nuclear Information System (INIS)

    2009-03-01

    In November 2006 Swedish Nuclear Fuels Co. applied for a license to build a plant for encapsulation of spent nuclear fuels at Oskarshamn, Sweden. The company also have plans to apply, in 2009, for a license to construct a underground repository for spent nuclear fuels. KASAM arranged a seminar in November 2006 in order to describe and discuss the licensing rules and regulations and the roles of different parties in the decision making. Another objective of the seminar was to point out possible ambiguities in this process. Another interesting question under discussion was in what ways the basic data for the decision should be produced. The seminar covered the part of the process beginning with the application for a license and ending with the government approval/rejection of the application. Most time was spent on the legal aspects of the process

  19. Final disposal of spent nuclear fuel - regulatory system and roles of different actors during the decision process

    Energy Technology Data Exchange (ETDEWEB)

    2009-03-15

    In November 2006 Swedish Nuclear Fuels Co. applied for a license to build a plant for encapsulation of spent nuclear fuels at Oskarshamn, Sweden. The company also have plans to apply, in 2009, for a license to construct a underground repository for spent nuclear fuels. KASAM arranged a seminar in November 2006 in order to describe and discuss the licensing rules and regulations and the roles of different parties in the decision making. Another objective of the seminar was to point out possible ambiguities in this process. Another interesting question under discussion was in what ways the basic data for the decision should be produced. The seminar covered the part of the process beginning with the application for a license and ending with the government approval/rejection of the application. Most time was spent on the legal aspects of the process

  20. Final disposal of spent nuclear fuels - regulations and the roles of different stakeholders during the decision making process

    International Nuclear Information System (INIS)

    2007-05-01

    In November 2006 Swedish Nuclear Fuels Co. applied for a license to build a plant for encapsulation of spent nuclear fuels at Oskarshamn, Sweden. The company also have plans to apply, in 2009, for a license to construct a underground repository for spent nuclear fuels. KASAM arranged a seminar in November 2006 in order to describe and discuss the licensing rules and regulations and the roles of different parties in the decision making. Another objective of the seminar was to point out possible ambiguities in this process. Another interesting question under discussion was in what ways the basic data for the decision should be produced. The seminar covered the part of the process beginning with the application for a license and ending with the government approval/rejection of the application. Most time was spent on the legal aspects of the process

  1. Process integration and waste heat recovery in Lithuanian and Danish industry. Final report phase 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-08-01

    The present document forms the Final Report for the first phase of the project `Process Integration and Waste Heat Recovery in Lithuanian and Danish Industry`. The project is carried out in the period 1995-1998 in a co-operation between the COWI offices in Lyngby and Vilnius, The Technical University of Denmark (Institute for Energetics), Kaunas University of Technology (CIPAI) and Vilnius Technical University, financed by The Danish Ministry of Energy`s EFP-95-programme, Lithuanian Energy Agency as well as the participants. The first phase of the project has comprised the establishment of the CIPAI centre (Centre for Industrial Process Analysis and Integration) at Kaunas University of Technology, training and knowledge transfer as well as elaboration of 6 industrial case-studies within the area of `Process Integration and waste Heat Recovery`. The second phase of the project has comprised R and D activities in this area in order to present general conclusions from the project as well as to present new and improved methods and tools for PI-analysis. The aim of the Final Report for the first phase of the project is to summarise project activities and the achieved results from case-studies and from the operation of the CIPAI-centre in general. (au)

  2. Final Technical Report - Advanced Optical Sensors to Minimize Energy Consumption in Polymer Extrusion Processes

    Energy Technology Data Exchange (ETDEWEB)

    Susan J. Foulk

    2012-07-24

    Project Objective: The objectives of this study are to develop an accurate and stable on-line sensor system to monitor color and composition on-line in polymer melts, to develop a scheme for using the output to control extruders to eliminate the energy, material and operational costs of off-specification product, and to combine or eliminate some extrusion processes. Background: Polymer extrusion processes are difficult to control because the quality achieved in the final product is complexly affected by the properties of the extruder screw, speed of extrusion, temperature, polymer composition, strength and dispersion properties of additives, and feeder system properties. Extruder systems are engineered to be highly reproducible so that when the correct settings to produce a particular product are found, that product can be reliably produced time after time. However market conditions often require changes in the final product, different products or grades may be processed in the same equipment, and feed materials vary from lot to lot. All of these changes require empirical adjustment of extruder settings to produce a product meeting specifications. Optical sensor systems that can continuously monitor the composition and color of the extruded polymer could detect process upsets, drift, blending oscillations, and changes in dispersion of additives. Development of an effective control algorithm using the output of the monitor would enable rapid corrections for changes in materials and operating conditions, thereby eliminating most of the scrap and recycle of current processing. This information could be used to identify extruder systems issues, diagnose problem sources, and suggest corrective actions in real-time to help keep extruder system settings within the optimum control region. Using these advanced optical sensor systems would give extruder operators real-time feedback from their process. They could reduce the amount of off-spec product produced and

  3. Adaptive Disturbance Rejection Control for Automatic Carrier Landing System

    Directory of Open Access Journals (Sweden)

    Xin Wang

    2016-01-01

    Full Text Available An adaptive disturbance rejection algorithm is proposed for carrier landing system in the final-approach. The carrier-based aircraft dynamics and the linearized longitudinal model under turbulence conditions in the final-approach are analyzed. A stable adaptive control scheme is developed based on LDU decomposition of the high-frequency gain matrix, which ensures closed-loop stability and asymptotic output tracking. Finally, simulation studies of a linearized longitudinal-directional dynamics model are conducted to demonstrate the performance of the adaptive scheme.

  4. Automated processing of whole blood units: operational value and in vitro quality of final blood components.

    Science.gov (United States)

    Jurado, Marisa; Algora, Manuel; Garcia-Sanchez, Félix; Vico, Santiago; Rodriguez, Eva; Perez, Sonia; Barbolla, Luz

    2012-01-01

    The Community Transfusion Centre in Madrid currently processes whole blood using a conventional procedure (Compomat, Fresenius) followed by automated processing of buffy coats with the OrbiSac system (CaridianBCT). The Atreus 3C system (CaridianBCT) automates the production of red blood cells, plasma and an interim platelet unit from a whole blood unit. Interim platelet unit are pooled to produce a transfusable platelet unit. In this study the Atreus 3C system was evaluated and compared to the routine method with regards to product quality and operational value. Over a 5-week period 810 whole blood units were processed using the Atreus 3C system. The attributes of the automated process were compared to those of the routine method by assessing productivity, space, equipment and staffing requirements. The data obtained were evaluated in order to estimate the impact of implementing the Atreus 3C system in the routine setting of the blood centre. Yield and in vitro quality of the final blood components processed with the two systems were evaluated and compared. The Atreus 3C system enabled higher throughput while requiring less space and employee time by decreasing the amount of equipment and processing time per unit of whole blood processed. Whole blood units processed on the Atreus 3C system gave a higher platelet yield, a similar amount of red blood cells and a smaller volume of plasma. These results support the conclusion that the Atreus 3C system produces blood components meeting quality requirements while providing a high operational efficiency. Implementation of the Atreus 3C system could result in a large organisational improvement.

  5. Analysis of reforming process of large distorted ring in final enlarging forging

    International Nuclear Information System (INIS)

    Miyazawa, Takeshi; Murai, Etsuo

    2002-01-01

    In the construction of reactors or pressure vessels for oil chemical plants and nuclear power stations, mono block open-die forging rings are often utilized. Generally, a large forged ring is manufactured by means of enlarging forging with reductions of the wall thickness. During the enlarging process the circular ring is often distorted and becomes an ellipse in shape. However the shape control of the ring is a complicated work. This phenomenon makes the matter still worse in forging of larger rings. In order to make precision forging of large rings, we have developed the forging method using a v-shape anvil. The v-shape anvil is geometrically adjusted to fit the distorted ring in the final circle and reform automatically the shape of the ring during enlarging forging. This paper has analyzed the reforming process of distorted ring by computer program based on F.E.M. and examined the effect on the precision of ring forging. (author)

  6. U.S. Department of Energy integrated manufacturing & processing predoctoral fellowships. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Petrochenkov, Margaret

    2003-03-31

    The objective of this program was threefold: to create a pool of PhDs trained in the integrated approach to manufacturing and processing, to promote academic interest in the field, and to attract talented professionals to this challenging area of engineering. It was anticipated that the program would result in the creation of new manufacturing methods that would contribute to improved energy efficiency, to better utilization of scarce resources, and to less degradation of the environment. Emphasis in the competition was on integrated systems of manufacturing and the integration of product design with manufacturing processes. Research addressed such related areas as aspects of unit operations, tooling and equipment, intelligent sensors, and manufacturing systems as they related to product design. This is the final report to close out the contract.

  7. Molecular-Level Processes Governing the Interaction of Contaminants with Iron and Manganese Oxides - Final Report; FINAL

    International Nuclear Information System (INIS)

    Brown, G. E. Jr.; Chambers, S. A.

    1999-01-01

    Many of the inorganic and organic contaminants present in sediments at DOE sites can be altered or destroyed by reduction and oxidation (redox) reactions occurring at mineral surfaces. A fundamental understanding of such redox processes provided by molecular-level studies on structurally and compositionally well-defined mineral surfaces will lead to: (i) improved models of contaminant fate and transport in geochemical systems, and (ii) optimized manipulation of these processes for remediation purposes. To contribute to this understanding, we will study, both experimentally and theoretically, redox processes involving three important contaminants - chromate ion, carbon tetrachloride, and trichloroethene TCE, on the following iron and manganese oxides - hematite, magnetite, maghemite, and pyrolusite. These oxides and their hydroxylated analogs commonly occur as coatings on minerals or as interfaces in the subsurface environment. Single-crystal surfaces of these oxides will be synthesized in carefully controlled fashion by molecular beam epitaxy. These surfaces, as well as high surface are powdered samples of these oxides, will be used in spectroscopic and kinetic experiments in both aqueous and gas phases. Our goal is to identify products and to determine the kinetics and mechanisms of surface-catalyzed redox reaction of Cr(VI) and CR(III), and the reductive dechlorination of carbon tetrachloride and TCE. The combination of theory and experiment will provide the base information needed to scale from the molecular level to the microscopic grain level minerals

  8. Development on the cryogenic hydrogen isotopes distillation process technology for tritium removal (Final report)

    Energy Technology Data Exchange (ETDEWEB)

    Sung, Ki Woung; Kim, Yong Ik; Na, Jeong Won; Ku, Jae Hyu; Kim, Kwang Rak; Jeong, Yong Won; Lee, Han Soo; Cho, Young Hyun; Ahn, Do Hee; Baek, Seung Woo; Kang, Hee Seok; Kim, You Sun [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1995-12-01

    While tritium exposure to the site-workers in Wolsung NPP is up to about 40% of the total personnel exposure, Ministry of Science and Technology has asked tritium removal facility for requirement of post heavy-water reactor construction. For the purpose of essential removal of tritium from the Wolsung heavy-water reactor system, a preliminary study on the cryogenic Ar-N{sub 2} and H{sub 2}-D{sub 2} distillation process for development of liquid-phase catalytic exchange cryogenic hydrogen distillation process technology. The Ar-N{sub 2} distillation column showed good performance with approximately 97% of final Ar concentration, and a computer simulation code was modified using these data. A simulation code developed for cryogenic hydrogen isotopes (H{sub 2}, HD, D{sub 2}, HT, DT, T{sub 2}) distillation column showed good performance after comparison with the result of a JAERI code, and a H{sub 2}-D{sub 2} distillation column was made. Gas chromatography for hydrogen isotopes analysis was established using a vacuum sampling loop, and a schematic diagram of H{sub 2}-D{sub 2} distillation process was suggested. A feasibility on modification of H{sub 2}-D{sub 2} distillation process control system using Laser Raman Spectroscopy was studied, and the consideration points for tritium storage system for Wolsung tritium removal facility was suggested. 31 tabs., 79 figs., 68 refs. (Author).

  9. Change of roles and attitudes in the Swedish localisation process for a final repository

    International Nuclear Information System (INIS)

    Hedberg, Bjoern

    2001-01-01

    Since the early research activities in the mid seventies related to a final repository for spent nuclear fuel and other radioactive wastes, much has changed in a direction that allows a more open and transparent decision-making process. Important changes have been noted in the legal framework - including EIA and financing - and in the roles of the Swedish authorities, local politicians, NGO's, and media. Trust and credibility is of course crucial for all actors in the decision-making process, but the ways to gain trust is different depending on which role to play in the process. A higher degree of trust in the different actors, and in the process itself, could be gained from a better distinction between facts and value judgements, but also if the roles of different actors are better clarified. To understand the roles of the different actors, it is important to define each actor's 'arena' in terms of responsibilities, goals, standpoints etc. in several dimensions. These dimensions could for example be geographic or the base for decisions (scientific - political)

  10. Change of roles and attitudes in the Swedish localisation process for a final repository

    Energy Technology Data Exchange (ETDEWEB)

    Hedberg, Bjoern [Swedish Radiation Protection Inst., Stockholm (Sweden)

    2001-07-01

    Since the early research activities in the mid seventies related to a final repository for spent nuclear fuel and other radioactive wastes, much has changed in a direction that allows a more open and transparent decision-making process. Important changes have been noted in the legal framework - including EIA and financing - and in the roles of the Swedish authorities, local politicians, NGO's, and media. Trust and credibility is of course crucial for all actors in the decision-making process, but the ways to gain trust is different depending on which role to play in the process. A higher degree of trust in the different actors, and in the process itself, could be gained from a better distinction between facts and value judgements, but also if the roles of different actors are better clarified. To understand the roles of the different actors, it is important to define each actor's 'arena' in terms of responsibilities, goals, standpoints etc. in several dimensions. These dimensions could for example be geographic or the base for decisions (scientific - political)

  11. Development on the cryogenic hydrogen isotopes distillation process technology for tritium removal (Final report)

    International Nuclear Information System (INIS)

    Sung, Ki Woung; Kim, Yong Ik; Na, Jeong Won; Ku, Jae Hyu; Kim, Kwang Rak; Jeong, Yong Won; Lee, Han Soo; Cho, Young Hyun; Ahn, Do Hee; Baek, Seung Woo; Kang, Hee Seok; Kim, You Sun

    1995-12-01

    While tritium exposure to the site-workers in Wolsung NPP is up to about 40% of the total personnel exposure, Ministry of Science and Technology has asked tritium removal facility for requirement of post heavy-water reactor construction. For the purpose of essential removal of tritium from the Wolsung heavy-water reactor system, a preliminary study on the cryogenic Ar-N 2 and H 2 -D 2 distillation process for development of liquid-phase catalytic exchange cryogenic hydrogen distillation process technology. The Ar-N 2 distillation column showed good performance with approximately 97% of final Ar concentration, and a computer simulation code was modified using these data. A simulation code developed for cryogenic hydrogen isotopes (H 2 , HD, D 2 , HT, DT, T 2 ) distillation column showed good performance after comparison with the result of a JAERI code, and a H 2 -D 2 distillation column was made. Gas chromatography for hydrogen isotopes analysis was established using a vacuum sampling loop, and a schematic diagram of H 2 -D 2 distillation process was suggested. A feasibility on modification of H 2 -D 2 distillation process control system using Laser Raman Spectroscopy was studied, and the consideration points for tritium storage system for Wolsung tritium removal facility was suggested. 31 tabs., 79 figs., 68 refs. (Author)

  12. LATE RENAL GRAFT REJECTION: PATHOLOGY AND PROGNOSIS

    Directory of Open Access Journals (Sweden)

    E.S. Stolyarevich

    2014-01-01

    Full Text Available Rejection has always been one of the most important cause of late renal graft dysfunction. Aim of the study was to analyze the prevalence of different clinico-pathological variants of rejection that cause late graft dysfunction, and evaluate their impact on long-term outcome. Materials and methods. This is a retrospective study that analyzed 294 needle core biopsy specimens from 265 renal transplant recipients with late (48,8 ± 46,1 months after transplantation allograft dysfunction caused by late acute rejection (LAR, n = 193 or chronic rejection (CR, n = 78 or both (n = 23. C4d staining was performed by immunofl uorescence (IF on frozen sections using a standard protocol. Results. Peritubular capillary C4d deposition was identifi ed in 36% samples with acute rejection and in 62% cases of chronic rejection (including 67% cases of transplant glomerulopathy, and 50% – of isolated chronic vasculopathy. 5-year graft survival for LAR vs CR vs their combination was 47, 13 and 25%, respectively. The outcome of C4d– LAR was (p < 0,01 better than of C4d+ acute rejection: at 60 months graft survival for diffuse C4d+ vs C4d− was 33% vs 53%, respectively. In cases of chronic rejection C4d+ vs C4d– it was not statistically signifi cant (34% vs 36%. Conclusion. In long-term allograft biopsy C4d positivity is more haracteristic for chronic rejection than for acute rejection. Only diffuse C4d staining affects the outcome. C4d– positivity is associated with worse allograft survival in cases of late acute rejection, but not in cases of chronic rejection

  13. Acute Hepatic Allograft Rejection in Pediatric Recipients: Effective Factors.

    Science.gov (United States)

    Dehghani, S M; Shahramian, I; Afshari, M; Bahmanyar, M; Ataollahi, M; Sargazi, A

    2018-01-01

    Acute cellular rejection (ACR), a reversible process, can affect the graft survival. To evaluate the relation between ACR and clinical factors in recipients of allograft liver transplantation. 47 recipients of liver were consecutively enrolled in a retrospective study. Their information were retrieved from their medical records and analyzed. Of the 47 recipients, 38 (81%) experienced acute rejection during 24 months of the transplantation. None of the studied factors for occurring transplant rejection, i.e ., blood groups, sex, age, familial history of disease, receiving drugs and blood products, type of donor, Child score, and Child class, was not found to be significant. During a limited follow-up period, we did not find any association between ACR and suspected risk factors.

  14. Simulation of the Press Hardening Process and Prediction of the Final Mechanical Material Properties

    Science.gov (United States)

    Hochholdinger, Bernd; Hora, Pavel; Grass, Hannes; Lipp, Arnulf

    2011-08-01

    Press hardening is a well-established production process in the automotive industry today. The actual trend of this process technology points towards the manufacturing of parts with tailored properties. Since the knowledge of the mechanical properties of a structural part after forming and quenching is essential for the evaluation of for example the crash performance, an accurate as possible virtual assessment of the production process is more than ever necessary. In order to achieve this, the definition of reliable input parameters and boundary conditions for the thermo-mechanically coupled simulation of the process steps is required. One of the most important input parameters, especially regarding the final properties of the quenched material, is the contact heat transfer coefficient (IHTC). The CHTC depends on the effective pressure or the gap distance between part and tool. The CHTC at different contact pressures and gap distances is determined through inverse parameter identification. Furthermore a simulation strategy for the subsequent steps of the press hardening process as well as adequate modeling approaches for part and tools are discussed. For the prediction of the yield curves of the material after press hardening a phenomenological model is presented. This model requires the knowledge of the microstructure within the part. By post processing the nodal temperature history with a CCT diagram the quantitative distribution of the phase fractions martensite, bainite, ferrite and pearlite after press hardening is determined. The model itself is based on a Hockett-Sherby approach with the Hockett-Sherby parameters being defined in function of the phase fractions and a characteristic cooling rate.

  15. Clean and efficient energy conversion processes (Cecon-project). Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    The objectives of the work programme reported are the development and testing of two optimised energy conversion processes, both consisting of a radiant surface gas burner and a ceramic heat exchanger. The first sub-objective of the programme is related to industrial heating, drying and curing processes requireing low and medium heat fluxes. It is estimated that around one tenth of the total EC industrial energy use is associated with such processes. The majority of these processes currently use convection and conduction as the main heat transfer mechanisms and overall energy efficiencies are typically below 25%. For many drying and finishing processes (such as curing powder coatings and drying paints, varnishes, inks, and for the fabrication of paper and textiles), radiant heating can achieve much faster dyring rates and higher energy efficiency than convective heating. In the project new concepts of natural gas fired radiant heating have been investigated which would be much more efficient than the existing processes. One element of the programme was the evelopment of gas burners having enhanced radiant efficiencies. A second concerned the investigation of the safety of gas burners containing significant volumes of mixed gas and air. Finally the new gas burners were tested in combination with the high temperature heat exchanger to create highly efficient radiant heating systems. The second sub-objective concerned the development of a compact low cost heat exchanger capable of achieving high levels of heat recovery (up to 60%) which could be easily installed on industrial processes. This would make heat recovery a practical proposition on processes where existing heat recovery technology is currently not cost effective. The project will have an impact on industrial processes consuming around 80 MTOE of energy per year within EU countries (1 MTOE equals 41.8 PJ). The overall energy saving potential of the project is estimated to be around 22 MTOE which is around 10

  16. Surface and subsurface cleanup protocol for radionuclides, Gunnison, Colorado, UMTRA project processing site: Final

    International Nuclear Information System (INIS)

    1994-01-01

    Thorium 230 (Th-230) at the Gunnison, Colorado processing site will require remediation, however, a seasonally fluctuating groundwater table at the site significantly complicates conventional remedial action with respect to cleanup. Therefore, to effectively remediate the site with respect to Radium 226 (Ra-226) and Th-230, the following supplemental standard is proposed: In situ Ra-26 will be remediated to the EPA soil cleanup standards independent of groundwater considerations. In situ Th-230 concentrations will be remediated in the region above the encountered water table so the 1000-year projected Ra-226 concentration complies with the EPA soil cleanup concentration limits. If elevated Th-230 persists to the water table, an additional foot of excavation will be performed and the grid will be backfilled. Excavated grids will be backfilled to the final remedial action grade with clean cobbly soil. Final grid verification that is required below the water table will be performed by extracting and analyzing a single bulk soil sample with the bucket of a backhoe. Modeled surface radon flux values will be estimated and documented. A recommendation will be made that land records should be annotated to identify the presence of residual Th-230

  17. Welding process

    International Nuclear Information System (INIS)

    Abdul Nassir Ibrahim; Azali Muhammad; Ab. Razak Hamzah; Abd. Aziz Mohamed; Mohamad Pauzi Ismail

    2008-01-01

    For the final chapter of this book, there is basic introduction on welding process. The good radiography must know somehow on welding process so that they can know what kind of welding that must rejected or not. All of the exposure technique that mention in earlier chapter almost applicable in this field because welding process is critical problem if there is no inspection will be done. So, for this chapter, all the discontinuity that usually appeared will be discussed and there is another discontinuity maybe not to important and do not give big impact if found it, do not described here. On top of that, the decision to accept or reject based on code, standard and specification that agreed by both to make sure that decision that agreed is corrected and more meaningful.

  18. Final report on the public involvement process phase 1, Monitored Retrievable Storage Facility Feasibility Study

    International Nuclear Information System (INIS)

    Moore, L.; Shanteau, C.

    1992-12-01

    This report summarizes the pubic involvement component of Phase 1 of the Monitored Retrievable Storage Facility (NM) Feasibility Study in San Juan County, Utah. Part of this summary includes background information on the federal effort to locate a voluntary site for temporary storage of nuclear waste, how San Juan County came to be involved, and a profile of the county. The heart of the report, however, summarizes the activities within the public involvement process, and the issues raised in those various forums. The authors have made every effort to reflect accurately and thoroughly all the concerns and suggestions expressed to us during the five month process. We hope that this report itself is a successful model of partnership with the citizens of the county -- the same kind of partnership the county is seeking to develop with its constituents. Finally, this report offers some suggestions to both county officials and residents alike. These suggestions concern how decision-making about the county's future can be done by a partnership of informed citizens and listening decision-makers. In the Appendix are materials relating to the public involvement process in San Juan County

  19. Final report on the public involvement process phase 1, Monitored Retrievable Storage Facility Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Moore, L.; Shanteau, C.

    1992-12-01

    This report summarizes the pubic involvement component of Phase 1 of the Monitored Retrievable Storage Facility (NM) Feasibility Study in San Juan County, Utah. Part of this summary includes background information on the federal effort to locate a voluntary site for temporary storage of nuclear waste, how San Juan County came to be involved, and a profile of the county. The heart of the report, however, summarizes the activities within the public involvement process, and the issues raised in those various forums. The authors have made every effort to reflect accurately and thoroughly all the concerns and suggestions expressed to us during the five month process. We hope that this report itself is a successful model of partnership with the citizens of the county -- the same kind of partnership the county is seeking to develop with its constituents. Finally, this report offers some suggestions to both county officials and residents alike. These suggestions concern how decision-making about the county's future can be done by a partnership of informed citizens and listening decision-makers. In the Appendix are materials relating to the public involvement process in San Juan County.

  20. Final report on the public involvement process phase 1, Monitored Retrievable Storage Facility Feasibility Study

    Energy Technology Data Exchange (ETDEWEB)

    Moore, L.; Shanteau, C.

    1992-12-01

    This report summarizes the pubic involvement component of Phase 1 of the Monitored Retrievable Storage Facility (NM) Feasibility Study in San Juan County, Utah. Part of this summary includes background information on the federal effort to locate a voluntary site for temporary storage of nuclear waste, how San Juan County came to be involved, and a profile of the county. The heart of the report, however, summarizes the activities within the public involvement process, and the issues raised in those various forums. The authors have made every effort to reflect accurately and thoroughly all the concerns and suggestions expressed to us during the five month process. We hope that this report itself is a successful model of partnership with the citizens of the county -- the same kind of partnership the county is seeking to develop with its constituents. Finally, this report offers some suggestions to both county officials and residents alike. These suggestions concern how decision-making about the county`s future can be done by a partnership of informed citizens and listening decision-makers. In the Appendix are materials relating to the public involvement process in San Juan County.

  1. Building more powerful less expensive supercomputers using Processing-In-Memory (PIM) LDRD final report.

    Energy Technology Data Exchange (ETDEWEB)

    Murphy, Richard C.

    2009-09-01

    This report details the accomplishments of the 'Building More Powerful Less Expensive Supercomputers Using Processing-In-Memory (PIM)' LDRD ('PIM LDRD', number 105809) for FY07-FY09. Latency dominates all levels of supercomputer design. Within a node, increasing memory latency, relative to processor cycle time, limits CPU performance. Between nodes, the same increase in relative latency impacts scalability. Processing-In-Memory (PIM) is an architecture that directly addresses this problem using enhanced chip fabrication technology and machine organization. PIMs combine high-speed logic and dense, low-latency, high-bandwidth DRAM, and lightweight threads that tolerate latency by performing useful work during memory transactions. This work examines the potential of PIM-based architectures to support mission critical Sandia applications and an emerging class of more data intensive informatics applications. This work has resulted in a stronger architecture/implementation collaboration between 1400 and 1700. Additionally, key technology components have impacted vendor roadmaps, and we are in the process of pursuing these new collaborations. This work has the potential to impact future supercomputer design and construction, reducing power and increasing performance. This final report is organized as follow: this summary chapter discusses the impact of the project (Section 1), provides an enumeration of publications and other public discussion of the work (Section 1), and concludes with a discussion of future work and impact from the project (Section 1). The appendix contains reprints of the refereed publications resulting from this work.

  2. The production of fuels and chemicals from food processing wastes & cellulosics. Final research report

    Energy Technology Data Exchange (ETDEWEB)

    Dale, M.C.; Okos, M.; Burgos, N. [and others

    1997-06-15

    High strength food wastes of about 15-20 billion pounds solids are produced annually by US food producers. Low strength food wastes of 5-10 billion pounds/yr. are produced. Estimates of the various components of these waste streams are shown in Table 1. Waste paper/lignocellulosic crops could produce 2 to 5 billion gallons of ethanol per year or other valuable chemicals. Current oil imports cost the US about $60 billion dollars/yr. in out-going balance of trade costs. Many organic chemicals that are currently derived from petroleum can be produced through fermentation processes. Petroleum based processes have been preferred over biotechnology processes because they were typically cheaper, easier, and more efficient. The technologies developed during the course of this project are designed to allow fermentation based chemicals and fuels to compete favorably with petroleum based chemicals. Our goals in this project have been to: (1) develop continuous fermentation processes as compared to batch operations; (2) combine separation of the product with the fermentation, thus accomplishing the twin goals of achieving a purified product from a fermentation broth and speeding the conversion of substrate to product in the fermentation broth; (3) utilize food or cellulosic waste streams which pose a current cost or disposal problem as compared to high cost grains or sugar substrates; (4) develop low energy recovery methods for fermentation products; and finally (5) demonstrate successful lab scale technologies on a pilot/production scale and try to commercialize the processes. The scale of the wastes force consideration of {open_quotes}bulk commodity{close_quotes} type products if a high fraction of the wastes are to be utilized.

  3. Permanent certification program for health information technology; revisions to ONC-Approved Accreditor processes. Final rule.

    Science.gov (United States)

    2011-11-25

    Under the authority granted to the National Coordinator for Health Information Technology by section 3001(c)(5) of the Public Health Service Act (PHSA) as added by the Health Information Technology for Economic and Clinical Health (HITECH) Act, this final rule establishes a process for addressing instances where the ONC-Approved Accreditor (ONC-AA) engages in improper conduct or does not perform its responsibilities under the permanent certification program. This rule also addresses the status of ONC-Authorized Certification Bodies (ONC-ACBs) in instances where there may be a change in the accreditation organization serving as the ONC-AA and clarifies the responsibilities of the new ONC-AA.

  4. Assessing middle school students` understanding of science relationships and processes: Year 2 - instrument validation. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Schau, C.; Mattern, N.; Weber, R.; Minnick, K.

    1997-01-01

    Our overall purpose for this multi-year project was to develop an alternative assessment format measuring rural middle school students understanding of science concepts and processes and the interrelationships among them. This kind of understanding is called structural knowledge. We had 3 major interrelated goals: (1) Synthesize the existing literature and critically evaluate the actual and potential use of measures of structural knowledge in science education. (2) Develop a structural knowledge alternative assessment format. (3) Examine the validity of our structural knowledge format. We accomplished the first two goals during year 1. The structural knowledge assessment we identified and developed further was a select-and-fill-in concept map format. The goal for our year 2 work was to begin to validate this assessment approach. This final report summarizes our year 2 work.

  5. New process modeling[sic], design, and control strategies for energy efficiency, high product quality, and improved productivity in the process industries. Final project report; FINAL

    International Nuclear Information System (INIS)

    Ray, W. Harmon

    2002-01-01

    This project was concerned with the development of process design and control strategies for improving energy efficiency, product quality, and productivity in the process industries. In particular, (i) the resilient design and control of chemical reactors, and (ii) the operation of complex processing systems, was investigated. Specific topics studied included new process modeling procedures, nonlinear controller designs, and control strategies for multiunit integrated processes. Both fundamental and immediately applicable results were obtained. The new design and operation results from this project were incorporated into computer-aided design software and disseminated to industry. The principles and design procedures have found their way into industrial practice

  6. Rejection as a call to arms: inter-racial hostility and support for political action as outcomes of race-based rejection in majority and minority groups.

    Science.gov (United States)

    Barlow, Fiona Kate; Sibley, Chris G; Hornsey, Matthew J

    2012-03-01

    Both majority and minority group members fear race-based rejection, and respond by disparaging the groups that they expect will reject them. It is not clear, however, how this process differs in minority and majority groups. Using large representative samples of White (N= 4,618) and Māori (N= 1,163) New Zealanders, we found that perceptions of race-based rejection predicted outgroup negativity in both groups, but in different ways and for different reasons. For White (but not Māori) New Zealanders, increased intergroup anxiety partially mediated the relationship between cognitions of rejection and outgroup negativity. Māori who expected to be rejected on the basis of their race reported increased ethnic identification and, in part through this, increased support for political action benefiting their own group. This finding supports collective-action models of social change in historically disadvantaged minority groups. © 2011 The British Psychological Society.

  7. 21 CFR 1230.47 - Rejected containers.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Rejected containers. 1230.47 Section 1230.47 Food... FEDERAL CAUSTIC POISON ACT Imports § 1230.47 Rejected containers. (a) In all cases where the containers... notification to the importer that the containers must be exported under customs supervision within 3 months...

  8. Final Regulatory Determination for Special Wastes From Mineral Processing (Mining Waste Exclusion) - Federal Register Notice, June 13, 1991

    Science.gov (United States)

    This action presents the Agency's final regulatory determination required by section 3001(b)(3)(C) of the Resource Conservation and Recovery Act (RCRA) for 20 special wastes from the processing of ores and minerals.

  9. Analysis of Turbine Load Rejection for APR1400 using SPACE

    International Nuclear Information System (INIS)

    Kim, Sang Jin; Park, Chan Eok; Choi, Jong Ho; Lee, Gyu Cheon

    2016-01-01

    Turbine Load Rejection event is one of the Performance Related Design Basis Event (PRDBE) that can be stabilized using plant control systems without any safety system actuation. The initiation of the event is turbine load rejection from 100% to 5% in 0.019 seconds. The NSSS control systems of APR1400 is composed of the Power Control System (PCS) and the Process-Component Control System (P-CCS). The PCS includes Reactor Regulating System (RRS), Reactor Power Cutback System (RPCS) and Digital Rod Control System (DRCS). The P-CCS includes the Pressurizer Pressure Control System (PPCS), the Pressurizer Level Control System (PLCS), the Feedwater Control System (FWCS) and the Steam Bypass Control System (SBCS). Turbine load rejection results in the increase of secondary pressure due to sudden blocking of steam flow to turbine. Then the Reactor Coolant System (RCS) cooling through steam generators is decreased rapidly and the RCS temperature will be increased. Turbine load rejection is a typical event to test NSSS control systems since it requires the automatic response of all major NSSS control systems. It is shown that the NSSS control systems of APR1400 have the capability to stabilize the plant without any safety system actuation for turbine load rejection event. This analysis results show that SPACE code has the capability to analyze the turbine load rejection event. However, further validation is necessary for other PRDBEs such as Two Main Feedwater Pumps Trip, Turbine Load Step Change and Turbine Load Ramp Down (5%/min) to verify the capability of SPACE for the full range of performance analyses

  10. Analysis of Turbine Load Rejection for APR1400 using SPACE

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sang Jin; Park, Chan Eok; Choi, Jong Ho; Lee, Gyu Cheon [KEPCO Engineering and Construction Co. Ltd., Deajeon (Korea, Republic of)

    2016-10-15

    Turbine Load Rejection event is one of the Performance Related Design Basis Event (PRDBE) that can be stabilized using plant control systems without any safety system actuation. The initiation of the event is turbine load rejection from 100% to 5% in 0.019 seconds. The NSSS control systems of APR1400 is composed of the Power Control System (PCS) and the Process-Component Control System (P-CCS). The PCS includes Reactor Regulating System (RRS), Reactor Power Cutback System (RPCS) and Digital Rod Control System (DRCS). The P-CCS includes the Pressurizer Pressure Control System (PPCS), the Pressurizer Level Control System (PLCS), the Feedwater Control System (FWCS) and the Steam Bypass Control System (SBCS). Turbine load rejection results in the increase of secondary pressure due to sudden blocking of steam flow to turbine. Then the Reactor Coolant System (RCS) cooling through steam generators is decreased rapidly and the RCS temperature will be increased. Turbine load rejection is a typical event to test NSSS control systems since it requires the automatic response of all major NSSS control systems. It is shown that the NSSS control systems of APR1400 have the capability to stabilize the plant without any safety system actuation for turbine load rejection event. This analysis results show that SPACE code has the capability to analyze the turbine load rejection event. However, further validation is necessary for other PRDBEs such as Two Main Feedwater Pumps Trip, Turbine Load Step Change and Turbine Load Ramp Down (5%/min) to verify the capability of SPACE for the full range of performance analyses.

  11. MR imaging of renal transplant rejection

    International Nuclear Information System (INIS)

    Hanna, S.; Helenon, O.; Legendre, C.; Chichie, J.F.; Di Stefano, D.; Kreis, H.; Moreau, J.F.; Hopital Necker, 75 - Paris

    1991-01-01

    The results of 62 consecutive MR examinations were correlated with the subsequent clinical course and histologic results. Twenty-six cases of rejection showed a marked diminution of cortico-medullary differentiation (CMD). The renal parenchymal vascular pattern and visibility of renal sinus fat were not markedly altered in rejection and there was no difference between normal and rejected allograft shape. The ability of MR imaging to diagnose renal transplant rejection is only based on CMD, which, however, is non-specific. In 2 cases of severe rejection, T2 weighted images showed an abnormal signal intensity of the cortex due to renal infarction. Our preliminary results in 8 patients with Gd-DOTA injection showed 2 cases with necrosis seen as areas with absent contrast enhancement. This technique seems to be promising in the detection of perfusion defects. (orig.)

  12. Risk of renal allograft rejection following angiography

    International Nuclear Information System (INIS)

    Heideman, M.; Claes, G.; Nilson, A.E.

    1976-01-01

    In a retrospective study of 173 immediately functioning primary kidney transplants, correlation between angiography and renal allograft rejection was studied during the first 14 days. It was found that rejection was more frequent in kidneys undergoing angiography than in those not undergoing angiography. It was also found that in kidneys undergoing angiography an overwhelming number of the rejections started the day after angiography. These differences in rejection frequency could not be explained by differences in HLA matching or the origin of the kidneys. These findings suggest a possible connection indicating that the angiography might elicit an acute rejection episode. A possible mechanism for starting this reaction might be activation of the complement system which was found in 50 percent of the patients undergoing angiography in peripheral blood and in 100 percent when studied in vitro

  13. Membrane/distillation hybrid process research and development. Final report, phase II

    Energy Technology Data Exchange (ETDEWEB)

    Mazanec, T.J.

    1997-07-01

    This report covers work conducted under the grant awarded to BP by DOE in late 1991 entitled {open_quotes}Membrane/Distillation Hybrid Process Research and Development.{close_quotes} The program was directed towards development and commercialization of the BP process for separation of vapor phase olefins from non-olefins via facilitated transport using an aqueous facilitator. The program has come to a very successful conclusion, with formation of a partnership between BP and Stone and Webster Engineering Corporation (SWEC) to market and commercialize the technology. The focus of this report is the final portion of the program, during which engineering re-design, facilitator optimization, economic analysis, and marketing have been the primary activities. At the end of Phase II BP was looking to partner with an engineering firm to advance the selective olefin recovery (SOR) technology from the lab/demo stage to full commercialization. In August 1995 BP and SWEC reached an agreement to advance the technology by completing additional Phase III work with DOE and beginning marketing activities.

  14. Advanced Analog Signal Processing for Fuzing Final Report CRADA No. TC-1306-96

    Energy Technology Data Exchange (ETDEWEB)

    Fu, C. Y. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Spencer, D. [Raymond Engineering, Middletown, CT (United States)

    2018-01-24

    The purpose of this CRADA between LLNL and Kaman Aerospace/Raymond Engineering Operations (Raymond) was to demonstrate the feasibility of using Analog/Digital Neural Network (ANN) Technology for advanced signal processing, fuzing, and other applications. This cooperation sought to Ieverage the expertise and capabilities of both parties--Raymond to develop the signature recognition hardware system, using Raymond’s extensive experience in the area of system development plus Raymond’s knowledge of military applications, and LLNL to apply ANN and related technologies to an area of significant interest to the United States government. This CRADA effort was anticipated to be a three-year project consisting of three phases: Phase I, Proof-of-Principle Demonstration; Phase II, Proof-of-Design, involving the development of a form-factored integrated sensor and ANN technology processo~ and Phase III, Final Design and Release of the integrated sensor and ANN fabrication process: Under Phase I, to be conducted during calendar year 1996, Raymond was to deliver to LLNL an architecture (design) for an ANN chip. LLNL was to translate the design into a stepper mask and to produce and test a prototype chip from the Raymond design.

  15. Black hole evaporation in a heat bath as a nonequilibrium process and its final fate

    International Nuclear Information System (INIS)

    Saida, Hiromi

    2007-01-01

    We consider a black hole in a heat bath, and the whole system which consists of the black hole and the heat bath is isolated from outside environments. When the black hole evaporates, the Hawking radiation causes an energy flow from the black hole to the heat bath. Therefore, since no energy flow arises in an equilibrium state, the thermodynamic state of the whole system is not in equilibrium. That is, in a region around the black hole, the matter field of Hawking radiation and that of heat bath should be in a nonequilibrium state due to the energy flow. Using a simple model which reflects the nonequilibrium nature of energy flow, we find the nonequilibrium effect on a black hole evaporation as follows: if the nonequilibrium region around a black hole is not so large, the evaporation time scale of a black hole in a heat bath becomes longer than that in an empty space (a situation without heat bath), because of the incoming energy flow from the heat bath to the black hole. However, if the nonequilibrium region around a black hole is sufficiently large, the evaporation time scale in a heat bath becomes shorter than that in an empty space, because a nonequilibrium effect of the temperature difference between the black hole and heat bath appears as a strong energy extraction from the black hole by the heat bath. Further, a specific nonequilibrium phenomenon is found: a quasi-equilibrium evaporation stage under the nonequilibrium effect proceeds abruptly to a quantum evaporation stage at a semi-classical level (at black hole radius R g > Planck length) within a very short time scale with a strong burst of energy. (Contrarily, when the nonequilibrium effect is not taken into account, a quasi-equilibrium stage proceeds smoothly to a quantum stage at R g < Planck length without so strong an energy burst.) That is, the nonequilibrium effect of energy flow tends to make a black hole evaporation process more dynamical and to accelerate that process. Finally, on the final fate

  16. Repair of pathology of structure with mortar to reject the red ceramics

    International Nuclear Information System (INIS)

    Santana, Claudeir de Souza; Santos, Juzelia

    2010-01-01

    The aim of this research is the use of the reject of red ceramic from an industry of bricks and tiles from the region of Cuiaba as mortar for repair of structural pathology, looking for their application to replace the sand and gravel in the process. The mortar produced restores a park bench made of concrete which seat was made of red ceramic and legs of soil-cement bricks. The reject of red ceramic used is from an industry in the region of Cuiaba, discarded at the end of the production process, ground in an appropriate granulometry to simulate a generic type of sand and gravel. Grinding processes were developed and various granulometric curves were drawned. The aggregates produced were characterized from the deposit until the final grinding according to ABNT norms in force, the specific area by BET, was used for microanalysis X-ray diffraction. ABNT standards were used to characterize and compare the results. The mortar produced proved to be adequate for the proposal restoration, it was consistent and cohesive. It was concluded that the mortar produced with recycled aggregate of red ceramic can be used in structural restoration in civil construction to replace the natural aggregate, with cost and environmental benefits. (author)

  17. Sensitivity of scintigraphy with 111In-lymphocytes for detection of cardiac allograft rejection

    International Nuclear Information System (INIS)

    Eisenberg, S.B.; Eisen, H.J.; Sobel, B.E.; Bergmann, S.R.; Bolman, R.M. III

    1988-01-01

    We recently demonstrated the feasibility of noninvasive detection of cardiac allograft rejection after administration of indium-111-labeled lymphocytes. To determine the sensitivity and specificity of the technique, as well as its value for delineating the severity of rejection, we studied 16 dogs with heterotopic thoracic cardiac allografts. Five animals were evaluated while exposed to immunosuppressive agents. Animals were scanned sequentially after administration of 100-400 microCi of indium-111-labeled autologous lymphocytes. Myocardial lymphocyte infiltration was expressed as the indium excess (IE), defined as the ratio of indium activity of the transplant or native heart compared with that in blood. Scintigraphic results were compared with characteristics of simultaneously obtained endomyocardial biopsies. Among 17 biopsy documented episodes of rejection, 16 were detected scintigraphically. Among 18 biopsies with no evidence of rejection, scintigraphy was uniformly negative. Thus, the sensitivity and specificity of scintigraphy were 94 and 100%, respectively. Biopsies graded as showing no rejection were associated with an IE of 0.3 +/- 0.5 (+/- SD); those graded as mild, 2.8 +/- 1.7; those as moderate, 10.7 +/- 7.2; and those graded as indicative of severe rejection, 14.2 +/- 4.5. Thus, scintigraphy with indium-111-labeled lymphocytes sensitively and specifically detects cardiac allograft rejection and delineates the intensity of the rejection process. It should be useful clinically for assessing potential allograft rejection noninvasively

  18. Combination processes for food irradiation. Proceedings of the final research co-ordination meeting

    International Nuclear Information System (INIS)

    1998-01-01

    There is an increasing consumer demand for food that is safe, minimally processed, visually attractive, full flavoured, nutritious, and convenient to prepare and serve, that has fewer preservatives, and that is available throughout the year at an affordable cost. Consumer concern and regulatory restrictions on the use of preservatives and pesticides in food are adversely affecting international trade in many food products. As a result, minimally processed, chilled foods and ready to eat foods are increasingly being marketed to satisfy consumer demand in both developed and developing countries. However, such foods could introduce new microbiological risks to the population, especially to those who are immunocompromised or generally at risk (children, pregnant women, the elderly, etc.). In view of these factors, a 5 year Co-ordinated Research Programme (CRP) on Irradiation in Combination with Other Processes for Improving Food Quality was initiated in 1991 by the Food and Agriculture Organization of the United Nations and the International Atomic Energy Agency through their Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture. The objectives of this CRP were to evaluate: 1) Combination treatment involving irradiation in order to extend the self-life of meat, seafood, fruits and vegetables at refrigeration temperatures and under ambient conditions; 2) Combination treatment involving irradiation in order to ensure the microbiological safety of foods, both individual and composite, including prepared meals; 3) Shelf-life extension of chilled, prepared meals and the development of shelf stable food and food components through combination treatment involving irradiation; 4) Energy requirements of combination processes involving irradiation in comparison to other food processes. Scientists from 14 countries participated in the CRP by carrying out the work under Research Contracts and Agreements with the Joint FAO/IAEA Division. The first Research Co

  19. Medical Examination of Aliens--Revisions to Medical Screening Process. Final rule.

    Science.gov (United States)

    2016-01-26

    The Centers for Disease Control and Prevention (CDC), within the Department of Health and Human Services (HHS), is issuing this final rule (FR) to amend its regulations governing medical examinations that aliens must undergo before they may be admitted to the United States. Based on public comment received, HHS/CDC did not make changes from the NPRM published on June 23, 2015. Accordingly, this FR will: Revise the definition of communicable disease of public health significance by removing chancroid, granuloma inguinale, and lymphogranuloma venereum as inadmissible health-related conditions for aliens seeking admission to the United States; update the notification of the health-related grounds of inadmissibility to include proof of vaccinations to align with existing requirements established by the Immigration and Nationality Act (INA); revise the definitions and evaluation criteria for mental disorders, drug abuse and drug addiction; clarify and revise the evaluation requirements for tuberculosis; clarify and revise the process for the HHS/CDC-appointed medical review board that convenes to reexamine the determination of a Class A medical condition based on an appeal; and update the titles and designations of federal agencies within the text of the regulation.

  20. Wet and dry deposition and resuspension of AFCT/TFCT fuel processing radionuclides. Final report

    International Nuclear Information System (INIS)

    Slinn, W.G.N.; Katen, P.C.; Wolf, M.A.; Loveland, W.D.; Radke, L.F.; Miller, E.L.; Ghannam, L.J.; Reynolds, B.W.; Vickers, D.

    1979-09-01

    After short summary and introductory chapters, Chapter IV contains a critical analysis of available parameterizations for resuspension and for wet and dry removal processes and recommends interim parameterizations for use in radiation dose calculations. Chapter V describes methods and experimental results from field studies of in-cloud vs below-cloud scavenging, precipitation efficiency, and modifications of aerosols by clouds. In Chapter VI are contained descriptions of methods and results from four different approaches to the problem of measuring the dry deposition velocities of submicron aerosol particles depositing on vegetation. Chapter VII describes experimental results from a study of resuspension and weathering of tracer aerosol particles deposited on soil, grass and gravel; typical resuspension rates were found to be of the order of 10 -8 s -1 and it is recommended that the concept of weathering be reassessed. In Chapter VIII, National Weather Service data are used to obtain Lagrangian statistics for use in a regional-scale study of wet and dry removal. Chapter IX develops new concepts in reservoir models for application at regional to global scales. In the final chapter are some comments about the results found in this study and recommendations for future research

  1. ERROR VS REJECTION CURVE FOR THE PERCEPTRON

    OpenAIRE

    PARRONDO, JMR; VAN DEN BROECK, Christian

    1993-01-01

    We calculate the generalization error epsilon for a perceptron J, trained by a teacher perceptron T, on input patterns S that form a fixed angle arccos (J.S) with the student. We show that the error is reduced from a power law to an exponentially fast decay by rejecting input patterns that lie within a given neighbourhood of the decision boundary J.S = 0. On the other hand, the error vs. rejection curve epsilon(rho), where rho is the fraction of rejected patterns, is shown to be independent ...

  2. Family and community rejection and a Congolese led mediation intervention to reintegrate rejected survivors of sexual violence in Eastern Democratic Republic of Congo.

    Science.gov (United States)

    Kohli, Anjalee; Tosha, Maphie; Ramazani, Paul; Safari, Octave; Bachunguye, Richard; Zahiga, Isaya; Iragi, Aline; Glass, Nancy

    2013-01-01

    Our purpose in this study is to describe the multiple and inter-related health, economic, and social reasons for rejection and to provide an example of a Congolese-led family mediation program to reintegrate survivors into their families. We conducted this study in Eastern Democratic Republic of Congo (DRC) and included two focus group discussions and twenty-seven interviews. Rejection extends beyond physical dislocation to include economic and social aspects. Family mediation is a process requiring knowledge of traditions and norms. Understanding the context of rejection and supporting promising local reintegration efforts will likely improve health, economic, and social outcomes for the survivor, her family, and her community.

  3. PHOSPHATES REMOVAL FROM REJECT WATER FROM DIGESTION OF SLUDGE

    Directory of Open Access Journals (Sweden)

    Elżbieta Sperczyńska

    2016-06-01

    Full Text Available The aim of the research work was to evaluate if coagulants used on technical scale are useful in phosphates removal from reject water. Effectiveness of phosphorus compounds removal from reject water from digestion of sewage sludge was examined. Selected prehydrolysed alkaline aluminium polychlorides were used. The results were compared to the ones obtained with aluminium sulphate. Reject water from digestion of sewage sludge form WWTP of 100 000 PE were examined. Commercial agents – prehydrolysed PAX 18, PAX XL10, PAX-XL1905 as well as aluminium sulphate were used. Various doses of coagulants: 0.7; 1.0; 1.5 – time higher than stoichiometric dose were applied. Stoichiometric dose was calculated based on chemical reaction of insoluble aluminium phosphate formation. Concentrations of Kiejdahl nitrogen (891 mgNKj/dm3, phosphates (125 mgPO43-/dm3 and organic compounds - COD (592 mgO2/dm3 in reject water were very high. The effectiveness of coagulation process increased as the doses of chemical agents increased. The most effective doses were the highest ones used during the experiment. The most effective agent was PAX 18 (96% removal efficiency. As the phosphates concentration decreased COD content declined simultaneously. Maximum COD removal (47% was obtained when highly alkaline PAX XL 1905 was used. Use of the lowest dose of Al2(SO43 allowed for 50% phosphates removal, whereas the lowest dose of PAX 18 decreased phosphates concentration by 83%.

  4. Development and evaluation of the process for final placement application: a review of the new student led allocation system

    OpenAIRE

    Mason, Rachael; Brackenbury, Debra; Broady, Sophie

    2016-01-01

    Background A process to facilitate nursing students to have more ownership of their final placement was introduced for this academic year by inviting them to apply for a specific placement they felt most appropriate. Whilst there has been significant research into preparing students for practice (Woods et al, 2015) and to explore the transition from student to graduate nurse (Kumaran and Carney, 2014), there is little to explore the effect of gaining preference for their final placement or...

  5. Final Report on the Audit of the Administration of the Contract Closeout Process at the Defense Contract Management Region, Dallas

    Science.gov (United States)

    1990-09-18

    This is our final report on the Audit of the Administration of the Contract Closeout Process at the Defense Contract Management Region, Dallas (DCMR... audit was made from January to October 1989. The objectives of the audit were to determine the timeliness of the contract closeout process, the validity...As part of the audit , we also evaluated internal controls over the contract closeout process. As of December 31, 1988, the Contract Administration

  6. European consumers' acceptance and rejection of novel beef technologies

    DEFF Research Database (Denmark)

    de Barcellos, Marcia Dutra; Kügler, Jens Oliver; Grunert, Klaus G.

    As part of ProSafeBeef, an integrated research project funded by the European Commission, the present qualitative study was carried out with European consumers to obtain insights into their acceptance or rejection of eight selected novel beef production and processing technologies, identified here...... capital cities: Madrid, Paris, Berlin and London. A common and translated topic guide was developed prior to the field work. A ranking exercise was applied, where the participants classified the technologies into accepted, neutral or rejected concepts, after discussing the perceived benefits and risks...... in society, global warming crisis, disease outbreaks and degradation of the environment are shaping consumers' opinion in regard to food production. There was a severe criticism about too much intervention in food and a strong desire to keep food and beef processing as simple and natural as possible....

  7. Vascular endothelium as a target of immune response in renal transplant rejection

    Directory of Open Access Journals (Sweden)

    Giovanni ePiotti

    2014-10-01

    Full Text Available This review of clinical and experimental studies aims at analysing the interplay between graft endothelium and host immune system in renal transplantation, and how it affects the survival of the graft. Graft endothelium is indeed the first barrier between self and non-self that is encountered by host lymphocytes upon reperfusion of vascularised solid transplants. Endothelial cells express all the major sets of antigens that elicit host immune response, and therefore represent a preferential target in organ rejection.Some of the antigens expressed by endothelial cells are target of the antibody-mediated response, such as the AB0 blood group system, the HLA and MICA systems, and the endothelial cell-restricted antigens; for each of these systems, the mechanisms of interaction and damage of both preformed and de novo donor-specific antibodies are reviewed along with their impact on renal graft survival. Moreover the rejection process can force injured endothelial cells to expose cryptic self-antigens, toward which an auto-immune response mounts, overlapping to the allo-immune response in the damaging of the graft. Not only are endothelial cells a passive target of the host immune response, but also an active player in lymphocyte activation; therefore their interaction with allogenic T-cells is analysed on the basis of experimental in vitro and in vivo studies, according to the patterns of expression of the HLA class I and II and the co-stimulatory molecules specific for cytotoxic and helper T-cells.Finally, as the response that follows transplantation has proven to be not necessarily destructive, the factors that foster graft endothelium functioning in spite of rejection, and how they could be therapeutically harnessed to promote long-term graft acceptance, are described: accommodation that is resistance of endothelial cells to donor-specific antibodies, and endothelial cell ability to induce Foxp3+ Regulatory T-cells, that are crucial mediators of

  8. Structural Decoupling and Disturbance Rejection in a Distillation Column

    DEFF Research Database (Denmark)

    Bahar, Mehrdad; Jantzen, Jan; Commault, C.

    1996-01-01

    Introduction, distillation column model, input-output decoupling, disturbance rejection, concluding remarks, references.......Introduction, distillation column model, input-output decoupling, disturbance rejection, concluding remarks, references....

  9. Applied research and evaluation of process concepts for liquefaction and gasification of western coals. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Wiser, W. H.

    1980-09-01

    Fourteen sections, including five subsections, of the final report covering work done between June 1, 1975 to July 31, 1980 on research programs in coal gasification and liquefaction have been entered individually into EDB and ERA. (LTN)

  10. Corneal Graft Rejection: Incidence and Risk Factors

    Directory of Open Access Journals (Sweden)

    Alireza Baradaran-Rafii

    2008-12-01

    Full Text Available

    PURPOSE: To determine the incidence and risk factors of late corneal graft rejection after penetrating keratoplasty (PKP. METHODS: Records of all patients who had undergone PKP from 2002 to 2004 without immunosuppressive therapy other than systemic steroids and with at least one year of follow up were reviewed. The role of possible risk factors such as demographic factors, other host factors, donor factors, indications for PKP as well as type of rejection were evaluated. RESULTS: During the study period, 295 PKPs were performed on 286 patients (176 male, 110 female. Mean age at the time of keratoplasty was 38±20 (range, 40 days to 90 years and mean follow up period was 20±10 (range 12-43 months. Graft rejection occurred in 94 eyes (31.8% at an average of 7.3±6 months (range, 20 days to 39 months after PKP. The most common type of rejection was endothelial (20.7%. Corneal vascularization, regrafting, anterior synechiae, irritating sutures, active inflammation, additional anterior segment procedures, history of trauma, uncontrolled glaucoma, prior graft rejection, recurrence of herpetic infection and eccentric grafting increased the rate of rejection. Patient age, donor size and bilateral transplantation had no significant influence on graft rejection. CONCLUSION: Significant risk factors for corneal graft rejection include

  11. Emotion Dysregulation Mediates the Relation between Mindfulness and Rejection Sensitivity.

    Science.gov (United States)

    Velotti, Patrizia; Garofalo, Carlo; Bizzi, Fabiola

    2015-09-01

    The role of rejection sensitivity (RS; the tendency to anxiously expect, readily perceive, and overreact to implied or overt interpersonal rejection) in psychopathology has mainly been studied with regard to borderline personality disorder (BPD). In the present study, we first sought to extend previous evidence of heightened RS in a clinical group with psychiatric disorders other than BPD, when compared with a community sample. Then, we tested whether emotion dysregulation and mindfulness were associated with RS in both sample, further hypothesizing that emotion dysregulation would mediate the relation between mindfulness deficits and RS. We adopted a cross-sectional design involving 191 psychiatric patients and 277 community participants (total N=468). All participants completed the Rejection Sensitivity Questionnaire, the Five Facet Mindfulness Questionnaire, and the Difficulties in Emotion Regulation Scale. Our hypotheses were supported, with psychiatric patients reporting greater levels of rejection sensitivity and emotion dysregulation, and lower level of mindfulness. Mindfulness deficits and emotion dysregulation explained a significant amount of variance in RS, in both samples. Finally, bootstrap analyses revealed that mindfulness deficits played an indirect effect on RS through the mediating role of emotion dysregulation. In particular, two different patterns emerged. Among psychiatric patients, an impairment in the ability to assume a non-judgmental stance towards own thoughts and feelings was related to RS through the mediation of limited access to emotion regulation strategies. Conversely, in the community sample, overall emotion dysregulation mediated the effect of lack of attention and awareness for present activities and experience on RS. Longitudinal studies could help in delineating etiological models of RS, and the joint role of deficits in mindfulness and emotion regulation should inform treatment programs.

  12. Image rejects in general direct digital radiography

    International Nuclear Information System (INIS)

    Hofmann, Bjørn; Rosanowsky, Tine Blomberg; Jensen, Camilla; Wah, Kenneth Hong Ching

    2015-01-01

    The number of rejected images is an indicator of image quality and unnecessary imaging at a radiology department. Image reject analysis was frequent in the film era, but comparably few and small studies have been published after converting to digital radiography. One reason may be a belief that rejects have been eliminated with digitalization. To measure the extension of deleted images in direct digital radiography (DR), in order to assess the rates of rejects and unnecessary imaging and to analyze reasons for deletions, in order to improve the radiological services. All exposed images at two direct digital laboratories at a hospital in Norway were reviewed in January 2014. Type of examination, number of exposed images, and number of deleted images were registered. Each deleted image was analyzed separately and the reason for deleting the image was recorded. Out of 5417 exposed images, 596 were deleted, giving a deletion rate of 11%. A total of 51.3% were deleted due to positioning errors and 31.0% due to error in centering. The examinations with the highest percentage of deleted images were the knee, hip, and ankle, 20.6%, 18.5%, and 13.8% respectively. The reject rate is at least as high as the deletion rate and is comparable with previous film-based imaging systems. The reasons for rejection are quite different in digital systems. This falsifies the hypothesis that digitalization would eliminates rejects. A deleted image does not contribute to diagnostics, and therefore is an unnecessary image. Hence, the high rates of deleted images have implications for management, training, education, as well as for quality

  13. Image rejects in general direct digital radiography.

    Science.gov (United States)

    Hofmann, Bjørn; Rosanowsky, Tine Blomberg; Jensen, Camilla; Wah, Kenneth Hong Ching

    2015-10-01

    The number of rejected images is an indicator of image quality and unnecessary imaging at a radiology department. Image reject analysis was frequent in the film era, but comparably few and small studies have been published after converting to digital radiography. One reason may be a belief that rejects have been eliminated with digitalization. To measure the extension of deleted images in direct digital radiography (DR), in order to assess the rates of rejects and unnecessary imaging and to analyze reasons for deletions, in order to improve the radiological services. All exposed images at two direct digital laboratories at a hospital in Norway were reviewed in January 2014. Type of examination, number of exposed images, and number of deleted images were registered. Each deleted image was analyzed separately and the reason for deleting the image was recorded. Out of 5417 exposed images, 596 were deleted, giving a deletion rate of 11%. A total of 51.3% were deleted due to positioning errors and 31.0% due to error in centering. The examinations with the highest percentage of deleted images were the knee, hip, and ankle, 20.6%, 18.5%, and 13.8% respectively. The reject rate is at least as high as the deletion rate and is comparable with previous film-based imaging systems. The reasons for rejection are quite different in digital systems. This falsifies the hypothesis that digitalization would eliminates rejects. A deleted image does not contribute to diagnostics, and therefore is an unnecessary image. Hence, the high rates of deleted images have implications for management, training, education, as well as for quality.

  14. 3.1.1.2 Feed Processing and Handling DL2 Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Elliott, Douglas C.; Magnuson, Jon K.; Wend, Christopher F.

    2006-09-30

    This milestone report is the deliverable for our Feed Processing and Handling project. It includes results of wet biomass feedstock analysis, slurry pumping information, fungal processing to produce a lignin-rich biorefinery residue and two subcontracted efforts to quantify the amount of wet biomass feedstocks currently available within the corn processing and paper processing industries.

  15. Assessment of energy requirements in proven and new copper processes. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Pitt, C.H.; Wadsworth, M.E.

    1980-12-31

    Energy requirements are presented for thirteen pyrometallurgical and eight hydrometallurgical processes for the production of copper. Front end processing, mining, mineral processing, gas cleaning, and acid plant as well as mass balances are included. Conventional reverberatory smelting is used as a basis for comparison. Recommendations for needed process research in copper production are presented.

  16. Allorecognition pathways in transplant rejection and tolerance.

    Science.gov (United States)

    Ali, Jason M; Bolton, Eleanor M; Bradley, J Andrew; Pettigrew, Gavin J

    2013-10-27

    With the advent of cellular therapies, it has become clear that the success of future therapies in prolonging allograft survival will require an intimate understanding of the allorecognition pathways and effector mechanisms that are responsible for chronic rejection and late graft loss.Here, we consider current understanding of T-cell allorecognition pathways and discuss the most likely mechanisms by which these pathways collaborate with other effector mechanisms to cause allograft rejection. We also consider how this knowledge may inform development of future strategies to prevent allograft rejection.Although both direct and indirect pathway CD4 T cells appear active immediately after transplantation, it has emerged that indirect pathway CD4 T cells are likely to be the dominant alloreactive T-cell population late after transplantation. Their ability to provide help for generating long-lived alloantibody is likely one of the main mechanisms responsible for the progression of allograft vasculopathy and chronic rejection.Recent work has suggested that regulatory T cells may be an effective cellular therapy in transplantation. Given the above, adoptive therapy with CD4 regulatory T cells with indirect allospecificity is a rational first choice in attempting to attenuate the development and progression of chronic rejection; those with additional properties that enable inhibition of germinal center alloantibody responses hold particular appeal.

  17. Why don't you like me? : Midfrontal theta power in response to unexpected peer rejection feedback

    NARCIS (Netherlands)

    van der Molen, M.J.W.; Dekkers, L.M.S.; Westenberg, P.M.; van der Veen, F.M.; van der Molen, M.W.

    2017-01-01

    Social connectedness theory posits that the brain processes social rejection as a threat to survival. Recent electrophysiological evidence suggests that midfrontal theta (4–8 Hz) oscillations in the EEG provide a window on the processing of social rejection. Here we examined midfrontal theta

  18. Systematic Process Synthesis and Design Methods for Cost Effective Waste Minimization. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Biegler, L.T.; Grossmann, I.E.; Westerberg, A.W.

    1998-02-14

    This report focuses on research done over the past four years under the grant with the above title. In addition, the report also includes a brief summary of work done before 1994 under grant DOE-DE-FG02-85ER13396. Finally, a complete list of publications that acknowledge support from this grant is listed at the end.

  19. Systematic Process Synthesis and Design Methods for Cost Effective Waste Minimization. Final report

    International Nuclear Information System (INIS)

    Biegler, L.T.; Grossmann, I.E.; Westerberg, A.W.

    1998-01-01

    This report focuses on research done over the past four years under the grant with the above title. In addition, the report also includes a brief summary of work done before 1994 under grant DOE-DE-FG02-85ER13396. Finally, a complete list of publications that acknowledge support from this grant is listed at the end

  20. ST2 IN REJECTION OF THE TRANSPLANTED HEART

    Directory of Open Access Journals (Sweden)

    O. P. Shevchenko

    2015-01-01

    Full Text Available This review summarizes the current literature devoted to the analysis of prognostic role of ST2 biomarker in rejection of the transplanted heart. ST2 is one of the most promising diagnostic markers of the development and severity of heart failure as well as the mortality risk in patients with cardiovascular diseases. ST2 is expressed in cardiomyocytes in response to a variety of pathological processes and mechanical damage to the heart, which allows diagnosing cardiovascular diseases before clinical manifestations. Presumably, measuring the level of ST2 in heart transplant may have diagnostic and prognostic value in the assessment of graft and risk of rejection. Currently, accumulated clinical data on the role of given biomarker in heart transplantation are not enough, and further research on the relation of ST2 levels with different clinical and laboratory parameters in heart recipients is necessary. 

  1. Adaptation of Rejection Algorithms for a Radar Clutter

    Directory of Open Access Journals (Sweden)

    D. Popov

    2017-09-01

    Full Text Available In this paper, the algorithms for adaptive rejection of a radar clutter are synthesized for the case of a priori unknown spectral-correlation characteristics at wobbulation of a repetition period of the radar signal. The synthesis of algorithms for the non-recursive adaptive rejection filter (ARF of a given order is reduced to determination of the vector of weighting coefficients, which realizes the best effectiveness index for radar signal extraction from the moving targets on the background of the received clutter. As the effectiveness criterion, we consider the averaged (over the Doppler signal phase shift improvement coefficient for a signal-to-clutter ratio (SCR. On the base of extreme properties of the characteristic numbers (eigennumbers of the matrices, the optimal vector (according to this criterion maximum is defined as the eigenvector of the clutter correlation matrix corresponding to its minimal eigenvalue. The general type of the vector of optimal ARF weighting coefficients is de-termined and specific adaptive algorithms depending upon the ARF order are obtained, which in the specific cases can be reduced to the known algorithms confirming its authenticity. The comparative analysis of the synthesized and known algorithms is performed. Significant bene-fits are established in clutter rejection effectiveness by the offered processing algorithms compared to the known processing algorithms.

  2. The significance of parenchymal changes of acute cellular rejection in predicting chronic liver graft rejection

    NARCIS (Netherlands)

    Gouw, ASH; van den Heuvel, MC; van den Berg, AP; Slooff, NJH; de Jong, KP; Poppema, S

    2002-01-01

    Background. Chronic rejection (CR) in liver allografts shows a rapid onset and progressive course, leading to graft failure within the first year after transplantation. Most cases are preceded by episodes of acute cellular rejection (AR), but histological features predictive for the transition

  3. Understanding Rejection between First-and-Second-Grade Elementary Students through Reasons Expressed by Rejecters.

    Science.gov (United States)

    García Bacete, Francisco J; Carrero Planes, Virginia E; Marande Perrin, Ghislaine; Musitu Ochoa, Gonzalo

    2017-01-01

    Objective: The aim of this research was to obtain the views of young children regarding their reasons for rejecting a peer. Method: To achieve this goal, we conducted a qualitative study in the context of theory building research using an analysis methodology based on Grounded Theory. The collected information was extracted through semi-structured individual interviews from a sample of 853 children aged 6 from 13 urban public schools in Spain. Results: The children provided 3,009 rejection nominations and 2,934 reasons for disliking the rejected peers. Seven reason categories emerged from the analysis. Four categories refer to behaviors of the rejected children that have a cost for individual peers or peer group such as: direct aggression, disturbance of wellbeing, problematic social and school behaviors and dominance behaviors. A further two categories refer to the identities arising from the preferences and choices of rejected and rejecter children and their peers: personal identity expressed through preferences and disliking, and social identity expressed through outgroup prejudices. The "no-behavior or no-choice" reasons were covered by one category, unfamiliarity. In addition, three context categories were found indicating the participants (interpersonal-group), the impact (low-high), and the subjectivity (subjective-objective) of the reason. Conclusion: This study provides researchers and practitioners with a comprehensive taxonomy of reasons for rejection that contributes to enrich the theoretical knowledge and improve interventions for preventing and reducing peer rejection.

  4. A Novel Slurry-Based Biomass Reforming Process Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Emerson, Sean C. [United Technologies Research Center, East Hartford, CT (United States); Davis, Timothy D. [United Technologies Research Center, East Hartford, CT (United States); Peles, A. [United Technologies Research Center, East Hartford, CT (United States); She, Ying [United Technologies Research Center, East Hartford, CT (United States); Sheffel, Joshua [United Technologies Research Center, East Hartford, CT (United States); Willigan, Rhonda R. [United Technologies Research Center, East Hartford, CT (United States); Vanderspurt, Thomas H. [United Technologies Research Center, East Hartford, CT (United States); Zhu, Tianli [United Technologies Research Center, East Hartford, CT (United States)

    2011-09-30

    This project was focused on developing a catalytic means of producing H2 from raw, ground biomass, such as fast growing poplar trees, willow trees, or switch grass. The use of a renewable, biomass feedstock with minimal processing can enable a carbon neutral means of producing H2 in that the carbon dioxide produced from the process can be used in the environment to produce additional biomass. For economically viable production of H2, the biomass is hydrolyzed and then reformed without any additional purification steps. Any unreacted biomass and other byproduct streams are burned to provide process energy. Thus, the development of a catalyst that can operate in the demanding corrosive environment and presence of potential poisons is vital to this approach. The concept for this project is shown in Figure 1. The initial feed is assumed to be a >5 wt% slurry of ground wood in dilute base, such as potassium carbonate (K2CO3). Base hydrolysis and reforming of the wood is carried out at high but sub-critical pressures and temperatures in the presence of a solid catalyst. A Pd alloy membrane allows the continuous removal of pure , while the retentate, including methane is used as fuel in the plant. The project showed that it is possible to economically produce H2 from woody biomass in a carbon neutral manner. Technoeconomic analyses using HYSYS and the DOE's H2A tool [1] were used to design a 2000 ton day-1 (dry basis) biomass to hydrogen plant with an efficiency of 46% to 56%, depending on the mode of operation and economic assumptions, exceeding the DOE 2012 target of 43%. The cost of producing the hydrogen from such a plant would be in the range of $1/kg H2 to $2/kg H2. By using raw biomass as a feedstock, the cost of producing hydrogen at large biomass consumption rates is more cost effective than steam reforming of hydrocarbons or biomass gasification and can achieve the overall cost goals of the DOE Fuel Cell Technologies Program. The complete conversion of wood

  5. Preventing Allograft Rejection by Targeting Immune Metabolism

    Directory of Open Access Journals (Sweden)

    Chen-Fang Lee

    2015-10-01

    Full Text Available Upon antigen recognition and co-stimulation, T lymphocytes upregulate the metabolic machinery necessary to proliferate and sustain effector function. This metabolic reprogramming in T cells regulates T cell activation and differentiation but is not just a consequence of antigen recognition. Although such metabolic reprogramming promotes the differentiation and function of T effector cells, the differentiation of regulatory T cells employs different metabolic reprogramming. Therefore, we hypothesized that inhibition of glycolysis and glutamine metabolism might prevent graft rejection by inhibiting effector generation and function and promoting regulatory T cell generation. We devised an anti-rejection regimen involving the glycolytic inhibitor 2-deoxyglucose (2-DG, the anti-type II diabetes drug metformin, and the inhibitor of glutamine metabolism 6-diazo-5-oxo-L-norleucine (DON. Using this triple-drug regimen, we were able to prevent or delay graft rejection in fully mismatched skin and heart allograft transplantation models.

  6. Rejection thresholds in solid chocolate-flavored compound coating.

    Science.gov (United States)

    Harwood, Meriel L; Ziegler, Gregory R; Hayes, John E

    2012-10-01

    Classical detection thresholds do not predict liking, as they focus on the presence or absence of a sensation. Recently however, Prescott and colleagues described a new method, the rejection threshold, where a series of forced choice preference tasks are used to generate a dose-response function to determine hedonically acceptable concentrations. That is, how much is too much? To date, this approach has been used exclusively in liquid foods. Here, we determined group rejection thresholds in solid chocolate-flavored compound coating for bitterness. The influences of self-identified preferences for milk or dark chocolate, as well as eating style (chewers compared to melters) on rejection thresholds were investigated. Stimuli included milk chocolate-flavored compound coating spiked with increasing amounts of sucrose octaacetate, a bitter and generally recognized as safe additive. Paired preference tests (blank compared to spike) were used to determine the proportion of the group that preferred the blank. Across pairs, spiked samples were presented in ascending concentration. We were able to quantify and compare differences between 2 self-identified market segments. The rejection threshold for the dark chocolate preferring group was significantly higher than the milk chocolate preferring group (P= 0.01). Conversely, eating style did not affect group rejection thresholds (P= 0.14), although this may reflect the amount of chocolate given to participants. Additionally, there was no association between chocolate preference and eating style (P= 0.36). Present work supports the contention that this method can be used to examine preferences within specific market segments and potentially individual differences as they relate to ingestive behavior. This work makes use of the rejection threshold method to study market segmentation, extending its use to solid foods. We believe this method has broad applicability to the sensory specialist and product developer by providing a

  7. Exceptional ion rejection ability of directional solvent for non-membrane desalination

    Energy Technology Data Exchange (ETDEWEB)

    Rish, Daniel [Department of Aerospace and Mechanical Engineering, University of Notre Dame, Notre Dame, Indiana 46556 (United States); Department of Civil Engineering, University of Notre Dame, Notre Dame, Indiana 46556 (United States); Luo, Shirui; Kurtz, Brien [Department of Aerospace and Mechanical Engineering, University of Notre Dame, Notre Dame, Indiana 46556 (United States); Luo, Tengfei, E-mail: tluo@nd.edu [Department of Aerospace and Mechanical Engineering, University of Notre Dame, Notre Dame, Indiana 46556 (United States); Center for Sustainable Energy at Notre Dame, University of Notre Dame, Notre Dame, Indiana 46556 (United States)

    2014-01-13

    The recently demonstrated directional solvent extraction (DSE) is promising for very low temperature, membrane-free water desalination. In this paper, we combine atomistic simulations and experimental validation to demonstrate that the currently used directional solvent, decanoic acid, can reject all major salt ions in seawater, with very high rejection rates. The salinities of the DSE recovered water show that ion rejection rates are ∼98%–99%—similar to those of the best reverse osmosis membranes. Our test also shows that the DSE process can desalt seawater to produce fresh water that meets drinking water standards.

  8. Parental Rejection Following Sexual Orientation Disclosure: Impact on Internalized Homophobia, Social Support, and Mental Health.

    Science.gov (United States)

    Puckett, Julia A; Woodward, Eva N; Mereish, Ethan H; Pantalone, David W

    2015-09-01

    Sexual minority individuals face unique stressors because of their sexual identity. We explored associations between parental reactions to children's coming out, internalized homophobia (IH), social support, and mental health in a sample of 257 sexual minority adults. Path analyses revealed that higher IH and lower social support mediated the association between past parental rejection and current psychological distress. Mental health providers may benefit clients by utilizing interventions that challenge internalized stereotypes about homosexuality, increase social support, and process parental rejection, as well as focusing on how certain crucial experiences of rejection may impact clients' IH and mental health.

  9. Exceptional ion rejection ability of directional solvent for non-membrane desalination

    International Nuclear Information System (INIS)

    Rish, Daniel; Luo, Shirui; Kurtz, Brien; Luo, Tengfei

    2014-01-01

    The recently demonstrated directional solvent extraction (DSE) is promising for very low temperature, membrane-free water desalination. In this paper, we combine atomistic simulations and experimental validation to demonstrate that the currently used directional solvent, decanoic acid, can reject all major salt ions in seawater, with very high rejection rates. The salinities of the DSE recovered water show that ion rejection rates are ∼98%–99%—similar to those of the best reverse osmosis membranes. Our test also shows that the DSE process can desalt seawater to produce fresh water that meets drinking water standards

  10. Rejecting empathy for animal ethics

    DEFF Research Database (Denmark)

    Kasperbauer, Tyler Joshua

    2015-01-01

    Ethicists have become increasingly skeptical about the importance of empathy in producing moral concern for others. One of the main claims made by empathy skeptics is a psychological thesis: empathy is not the primary psychological process responsible for producing moral concern. Some of the best...... evidence that could confirm or disconfirm this thesis comes from research on empathizing with animals. However, this evidence has not been discussed in any of the prominent critiques of empathy. In this paper, I investigate six different empirical claims commonly made about empathy toward animals. I find...... all six claims to be problematic, though some are more plausible than others, and argue that empathy is indeed not psychologically central to producing moral concern for animals. I also review evidence indicating that other moral emotions, particularly anger, are more strongly engaged with producing...

  11. Process system evaluation: Consolidated letter reports. Volume 3: Formulation of final products

    International Nuclear Information System (INIS)

    Josephson, G.B.; Chapman, C.C.; Albertsen, K.H.

    1996-04-01

    Glass discharged from the low-level waste (LLW) melter may be processed into a variety of different forms for storage and disposal. The purpose of the study reported here is to identify and evaluate processing options for forming the glass

  12. Transparent parsing : Head-driven processing of verb-final structures

    NARCIS (Netherlands)

    Mulders, I.C.M.C.

    2002-01-01

    The conceptual guideline underlying this study is that the goal of processing theory should be to construct a transparent parser. A transparent parser is a parser which employs only properties and relations that are available in the grammar, without resorting to processing-specific notions. Under

  13. Process acceptance and adjustment techniques for Swiss automatic screw machine parts. Final report

    International Nuclear Information System (INIS)

    Robb, J.M.

    1976-01-01

    Product tolerance requirements for small, cylindrical, piece parts produced on swiss automatic screw machines have progressed to the reliability limits of inspection equipment. The miniature size, configuration, and tolerance requirements (plus or minus 0.0001 in.) (0.00254 mm) of these parts preclude the use of screening techniques to accept product or adjust processes during setup and production runs; therefore, existing means of product acceptance and process adjustment must be refined or new techniques must be developed. The purpose of this endeavor has been to determine benefits gained through the implementation of a process acceptance technique (PAT) to swiss automatic screw machine processes. PAT is a statistical approach developed for the purpose of accepting product and centering processes for parts produced by selected, controlled processes. Through this endeavor a determination has been made of the conditions under which PAT can benefit a controlled process and some specific types of screw machine processes upon which PAT could be applied. However, it was also determined that PAT, if used indiscriminately, may become a record keeping burden when applied to more than one dimension at a given machining operation

  14. Solvent-refined-coal (SRC) process. Volume II. Sections V-XIV. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1982-05-01

    This report documents the completion of development work on the Solvent Refined Coal Process by The Pittsburgh and Midway Coal Mining Co. The work was initiated in 1966 under Office of Coal Research, US Department of Interior, Contract No. 14-01-0001-496 and completed under US Department of Energy Contract No. DE-AC05-79ET10104. This report discusses work leading to the development of the SRC-I and SRC-II processes, construction of the Fort Lewis Pilot Plant for the successful development of these processes, and results from the operation of this pilot plant. Process design data generated on a 1 ton-per-day Process Development Unit, bench-scale units and through numerous research projects in support of the design of major demonstration plants are also discussed in summary form and fully referenced in this report.

  15. High pre-transplant soluble CD30 levels are predictive of the grade of rejection.

    Science.gov (United States)

    Rajakariar, Ravindra; Jivanji, Naina; Varagunam, Mira; Rafiq, Mohammad; Gupta, Arun; Sheaff, Michael; Sinnott, Paul; Yaqoob, M M

    2005-08-01

    In renal transplantation, serum soluble CD30 (sCD30) levels in graft recipients are associated with increased rejection and graft loss. We investigated whether pre-transplant sCD30 concentrations are predictive of the grade of rejection. Pre-transplant sera of 51 patients with tubulointerstitial rejection (TIR), 16 patients with vascular rejection (VR) and an age-matched control group of 41 patients with no rejection (NR) were analyzed for sCD30. The transplant biopsies were immunostained for C4d. The median sCD30 level was significantly elevated in the group with VR (248 Units (U)/mL, range: 92-802) when compared with TIR (103 U/mL, range: 36-309, psCD30 levels compared to NR. Based on C4d staining, a TH2 driven process, the median sCD30 levels were significantly raised in C4d+ patients compared with C4d- group (177 U/mL vs. 120 U/mL, psCD30 levels measured at time of transplantation correlate with the grade of rejection. High pre-transplant levels are associated with antibody-mediated rejection which carries a poorer prognosis. sCD30 could be another tool to assess immunological risk prior to transplantation and enable a patient centered approach to immunosuppression.

  16. Redistribution of wastewater alkalinity with a microbial fuel cell to support nitrification of reject water.

    Science.gov (United States)

    Modin, Oskar; Fukushi, Kensuke; Rabaey, Korneel; Rozendal, René A; Yamamoto, Kazuo

    2011-04-01

    In wastewater treatment plants, the reject water from the sludge treatment processes typically contains high ammonium concentrations, which constitute a significant internal nitrogen load in the plant. Often, a separate nitrification reactor is used to treat the reject water before it is fed back into the plant. The nitrification reaction consumes alkalinity, which has to be replenished by dosing e.g. NaOH or Ca(OH)(2). In this study, we investigated the use of a two-compartment microbial fuel cell (MFC) to redistribute alkalinity from influent wastewater to support nitrification of reject water. In an MFC, alkalinity is consumed in the anode compartment and produced in the cathode compartment. We use this phenomenon and the fact that the influent wastewater flow is many times larger than the reject water flow to transfer alkalinity from the influent wastewater to the reject water. In a laboratory-scale system, ammonium oxidation of synthetic reject water passed through the cathode chamber of an MFC, increased from 73.8 ± 8.9 mgN/L under open-circuit conditions to 160.1 ± 4.8 mgN/L when a current of 1.96 ± 0.37 mA (15.1 mA/L total MFC liquid volume) was flowing through the MFC. These results demonstrated the positive effect of an MFC on ammonium oxidation of alkalinity-limited reject water. Copyright © 2011 Elsevier Ltd. All rights reserved.

  17. Lung allograft rejection in the rat. I. Accelerated rejection caused by graft lymphocytes

    International Nuclear Information System (INIS)

    Prop, J.; Nieuwenhuis, P.; Wildevuur, C.R.

    1985-01-01

    To find out to what extent rejection of lungs differs from that of other organs, functional rejection of lung allografts was studied in five combinations of inbred rat strains. Rejection could be monitored accurately by perfusion scintigraphy, and equally well by chest roentgenography. The rejection of lung grafts was found to proceed remarkably fast, when compared with heart grafts, in combinations with strong RT1-incompatibilities. This accelerated rejection pattern could be converted into rejection at a normal pace by pretreatment of the donor with 10 Gy roentgen irradiation one day before transplantation. Donor pretreatment depleted the lung graft's bronchus-associated lymphoid tissue (BALT) of lymphocytes. When grafts were depleted of all other passenger cells as well--by retransplantation from a cyclosporine-treated intermediate host--they showed an even more reduced immunogenicity, probably because of the loss of donor-type dendritic cells. These results indicate that lymphocytes from the BALT of lung grafts are capable of accelerating the rejection response

  18. Music genre recognition with risk and rejection

    DEFF Research Database (Denmark)

    Sturm, Bob L.

    2013-01-01

    We explore risk and rejection for music genre recognition (MGR) within the minimum risk framework of Bayesian classification. In this way, we attempt to give an MGR system knowledge that some misclassifications are worse than others, and that deferring classification to an expert may be a better...

  19. Ferrite grade iron oxides from ore rejects

    Indian Academy of Sciences (India)

    Iron oxyhydroxides and hydroxides were synthesized from chemically beneficiated high SiO2/Al2O3 low-grade iron ore (57.49% Fe2O3) rejects and heated to get iron oxides of 96–99.73% purity. The infrared band positions, isothermal weight loss and thermogravimetric and chemical analysis established the chemical ...

  20. Local graft irradiation in renal transplant rejection

    International Nuclear Information System (INIS)

    Kawamura, Masashi; Kataoka, Masaaki; Itoh, Hisao

    1990-01-01

    From 1977 to 1988, of 142 renal transplantations, seven recipients (4.9%) received local graft irradiation following rejective reaction refractory to antirejection medical managements. Concurrent with the administration of pulsed high dose methylprednisolone and other antirejection medical managements, the graft was irradiated with a total dose of 6.0 Gy-150 cGy per fraction every other day at the midplane of the graft using two opposing portals of 4MX Linac. The fields were defined by palpation and echography. All patients had improvements in serum creatinine on the 10th day after beginning the irradiation. Four patients with peripheral lymphocytosis during the irradiation combined with pulsed high dose methylprednisolone improved in renal functions. On the other hand, out of 3 patients with lymphcytopenic changes, in two the transplanted graft was removed due to deteriorations, and the other patient is currently suffering from chronic rejection. Local graft irradiation can be useful in maintaining a rejective graft and reversing its functions in some patients whose rejective reaction failed to respond to the antirejection medical managements. (author)

  1. The cost of ethanol production from lignocellulosic biomass -- A comparison of selected alternative processes. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Grethlein, H.E.; Dill, T.

    1993-04-30

    The purpose of this report is to compare the cost of selected alternative processes for the conversion of lignocellulosic biomass to ethanol. In turn, this information will be used by the ARS/USDA to guide the management of research and development programs in biomass conversion. The report will identify where the cost leverages are for the selected alternatives and what performance parameters need to be achieved to improve the economics. The process alternatives considered here are not exhaustive, but are selected on the basis of having a reasonable potential in improving the economics of producing ethanol from biomass. When other alternatives come under consideration, they should be evaluated by the same methodology used in this report to give fair comparisons of opportunities. A generic plant design is developed for an annual production of 25 million gallons of anhydrous ethanol using corn stover as the model substrate at $30/dry ton. Standard chemical engineering techniques are used to give first order estimates of the capital and operating costs. Following the format of the corn to ethanol plant, there are nine sections to the plant; feed preparation, pretreatment, hydrolysis, fermentation, distillation and dehydration, stillage evaporation, storage and denaturation, utilities, and enzyme production. There are three pretreatment alternatives considered: the AFEX process, the modified AFEX process (which is abbreviated as MAFEX), and the STAKETECH process. These all use enzymatic hydrolysis and so an enzyme production section is included in the plant. The STAKETECH is the only commercially available process among the alternative processes.

  2. Low Cost Chemical Feedstocks Using an Improved and Energy Efficient Natural Gas Liquid (NGL) Removal Process, Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Meyer, Howard, S.; Lu, Yingzhong

    2012-08-10

    the economic incentive to extract NGLs from domestically produced natural gas. Successful gas processors will be those who adopt technologies that are less energy intensive, have lower capital and operating costs and offer the flexibility to tailor the plant performance to maximize product revenue as market conditions change, while maintaining overall system efficiency. Presently, cryogenic turbo-expander technology is the dominant NGL recovery process and it is used throughout the world. This process is known to be highly energy intensive, as substantial energy is required to recompress the processed gas back to pipeline pressure. The purpose of this project is to develop a new NGL separation process that is flexible in terms of ethane rejection and can reduce energy consumption by 20-30% from current levels, particularly for ethane recoveries of less than 70%. The new process integrates the dehydration of the raw natural gas stream and the removal of NGLs in such a way that heat recovery is maximized and pressure losses are minimized so that high-value equipment such as the compressor, turbo-expander, and a separate dehydration unit are not required. GTI completed a techno-economic evaluation of the new process based on an Aspen-HYSYS simulation model. The evaluation incorporated purchased equipment cost estimates obtained from equipment suppliers and two different commercial software packages; namely, Aspen-Icarus and Preliminary Design and Quoting Service (PDQ$). For a 100 MMscfd gas processing plant, the annualized capital cost for the new technology was found to be about 10% lower than that of conventional technology for C2 recovery above 70% and about 40% lower than that of conventional technology for C2 recovery below 50%. It was also found that at around 40-50% C2 recovery (which is economically justifiable at the current natural gas prices), the energy cost to recover NGL using the new technology is about 50% of that of conventional cryogenic technology.

  3. SUMMARY REPORT OF THE DOE DIRECT LIQUEFACTION PROCESS DEVELOPMENT CAMPAIGN OF THE LATE TWENTIETH CENTURY; FINAL

    International Nuclear Information System (INIS)

    F.P. Burke; S.D. Brandes; D.C. McCoy; R.A. Winschel; D. Gray; G. Tomlinson

    2001-01-01

    Following the petroleum price and supply disruptions of 1973, the U.S. government began a substantial program to fund the development of alternative fuels. Direct coal liquefaction was one of the potential routes to alternative fuels. The direct coal liquefaction program was funded at substantial levels through 1982, and at much lower levels thereafter. Those processes that were of most interest during this period were designed to produce primarily distillate fuels. By 1999, U.S. government funding for the development of direct coal liquefaction ended. Now that the end of this campaign has arrived, it is appropriate to summarize the process learnings derived from it. This report is a summary of the process learnings derived from the DOE direct coal liquefaction process development campaign of the late twentieth century. The report concentrates on those process development programs that were designed to produce primarily distillate fuels and were largely funded by DOE and its predecessors in response to the petroleum supply and price disruptions of the 1970s. The report is structured as chapters written by different authors on most of the major individual DOE-funded process development programs. The focus of the report is process learnings, as opposed to, say, fundamental coal liquefaction science or equipment design. As detailed in the overview (Chapter 2), DOE's direct coal liquefaction campaign made substantial progress in improving the process yields and the quality of the distillate product. Much of the progress was made after termination by 1983 of the major demonstration programs of the ''first generation'' (SRC-II, H-Coal, EDS) processes

  4. Is the bitter rejection response always adaptive?

    Science.gov (United States)

    Glendinning, J I

    1994-12-01

    The bitter rejection response consists of a suite of withdrawal reflexes and negative affective responses. It is generally assumed to have evolved as a way to facilitate avoidance of foods that are poisonous because they usually taste bitter to humans. Using previously published studies, the present paper examines the relationship between bitterness and toxicity in mammals, and then assesses the ecological costs and benefits of the bitter rejection response in carnivorous, omnivorous, and herbivorous (grazing and browsing) mammals. If the bitter rejection response accurately predicts the potential toxicity of foods, then one would expect the threshold for the response to be lower for highly toxic compounds than for nontoxic compounds. The data revealed no such relationship. Bitter taste thresholds varied independently of toxicity thresholds, indicating that the bitter rejection response is just as likely to be elicited by a harmless bitter food as it is by a harmful one. Thus, it is not necessarily in an animal's best interest to have an extremely high or low bitter threshold. Based on this observation, it was hypothesized that the adaptiveness of the bitter rejection response depends upon the relative occurrence of bitter and potentially toxic compounds in an animal's diet. Animals with a relatively high occurrence of bitter and potentially toxic compounds in their diet (e.g., browsing herbivores) were predicted to have evolved a high bitter taste threshold and tolerance to dietary poisons. Such an adaptation would be necessary because a browser cannot "afford" to reject all foods that are bitter and potentially toxic without unduly restricting its dietary options. At the other extreme, animals that rarely encounter bitter and potentially toxic compounds in their diet (e.g., carnivores) were predicted to have evolved a low bitter threshold. Carnivores could "afford" to utilize such a stringent rejection mechanism because foods containing bitter and potentially

  5. Pre-engineering assessment of Enersolve Demonstration Project. Dairy processing plant. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1985-07-15

    This study involved evaluation of a dairy processing plant to demonstrate energy conservation potential and developing a strategy to realize energy savings through retrofitting and revamping. The cheese and whey making plant of Agropur Cooperative Agro-Alimentaire located in Quebec was selected as a representative Canadian dairy processing plant. The pre-engineering assessment included a review of existing facility at the plant and plant operation, identification of plant equipment or process steps where substantial economic benefits would result from retrofitting and revamping, and estimation of budgetary cost for the subsequent engineering, procurement, construction management and monitoring of the retrofitted equipment. 3 figs., 2 tabs.

  6. Water recovery and solid waste processing for aerospace and domestic applications. Volume 1: Final report

    Science.gov (United States)

    Murray, R. W.

    1973-01-01

    A comprehensive study of advanced water recovery and solid waste processing techniques employed in both aerospace and domestic or commercial applications is reported. A systems approach was used to synthesize a prototype system design of an advanced water treatment/waste processing system. Household water use characteristics were studied and modified through the use of low water use devices and a limited amount of water reuse. This modified household system was then used as a baseline system for development of several water treatment waste processing systems employing advanced techniques. A hybrid of these systems was next developed and a preliminary design was generated to define system and hardware functions.

  7. Low Voltage Electron Beam Processing Final Report CRADA No. TC-645-93-A

    Energy Technology Data Exchange (ETDEWEB)

    Chen, H. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Wakalopulos, G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-10-16

    This CRADA project was established to develop a small, inexpensive sealed-tube electron beam processing system having immediate applications in industrial, high speed manufacturing processes, and in the Department of Energy (DOE) waste treatment/cleanup operations. The technical work involved the development and demonstration of a compact, sealed, 50-75 kilovolt (kV) EB generator prototype, including controls and power supply. The specific goals of this project were to develop a low cost vacuum tube capable of shooting an electron beam several inches into the air, and to demonstrate that wide area materials processing is feasible by stacking the tubes to produce continuous beams. During the project, we successfully demonstrated the producibility of a low cost electron beam system and several material processing operations of interest to US industry, DOE and, since September 11, 2001, the Homeland Security.

  8. Fact Sheet - Final Air Toxics Rule for Gold Mine Ore Processing and Production

    Science.gov (United States)

    Fact sheet summarizing main points of National Emissions Standards for Hazardous Air Pollutants for gold ore processing and production facilities, the seventh largest source of mercury air emission in the United States.

  9. Development of a process for quantifying the benefits of research : final report.

    Science.gov (United States)

    2017-07-04

    MnDOT Research Services funds and administers approximately 180 transportation research projects annually at a cost of slightly more than $3 million. This project developed an easy-to-apply process for quantifying the potential benefits of research a...

  10. Electric utility engineer`s FGD manual -- Volume 1: FGD process design. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-04

    Part 1 of the Electric Utility Engineer`s Flue Gas Desulfurization (FGD) Manual emphasizes the chemical and physical processes that form the basis for design and operation of lime- and limestone-based FGD systems applied to coal- or oil-fired steam electric generating stations. The objectives of Part 1 are: to provide a description of the chemical and physical design basis for lime- and limestone-based wet FGD systems; to identify and discuss the various process design parameters and process options that must be considered in developing a specification for a new FGD system; and to provide utility engineers with process knowledge useful for operating and optimizing a lime- or limestone-based wet FGD system.

  11. Compatibility of manufacturing process fluids with R-134a and polyolester lubricant. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Cavestri, R.C.; Schooley, D.L. [Imagination Resources, Inc., Dublin, OH (United States)

    1996-07-01

    This report includes a broad list of processing fluids that are known to be used to manufacture air conditioning and refrigeration products. Sixty-four process fluids from this list were selected for compatibility studies with R-134a and ICI EMKARATE RL32H (32 ISO) polyolester lubricant. Solutions or suspensions of the process fluid residues in polyolester lubricant were heated for 14 days at 175{degrees}C (347{degrees}F) in evacuated sealed glass tubes containing only valve steel coupons. Miscibility tests were performed at 90 wt.% R-134a, 10 wt.% polyolester lubricant with process fluid residue contaminate and were scanned in 10{degrees}C (18{degrees}F) increments over a temperature range of ambient to -40{degrees}C (-40{degrees}F). Any sign of turbidity, haze formation or oil separation was considered the immiscibility point.

  12. Final Report Collaborative Project: Improving the Representation of Coastal and Estuarine Processes in Earth System Models

    Energy Technology Data Exchange (ETDEWEB)

    Bryan, Frank [Univ. of Connecticut, Storrs, CT (United States); Dennis, John [Univ. of Connecticut, Storrs, CT (United States); MacCready, Parker [Univ. of Connecticut, Storrs, CT (United States); Whitney, Michael M. [Univ. of Connecticut, Storrs, CT (United States)

    2016-09-30

    This project aimed to improve long term global climate simulations by resolving and enhancing the representation of the processes involved in the cycling of freshwater through estuaries and coastal regions. This was a collaborative multi-institution project consisting of physical oceanographers, climate model developers, and computational scientists. It specifically targeted the DOE objectives of advancing simulation and predictive capability of climate models through improvements in resolution and physical process representation.

  13. Y-12 National Security Complex Emergency Management Hazards Assessment (EMHA) Process; FINAL

    International Nuclear Information System (INIS)

    Bailiff, E.F.; Bolling, J.D.

    2001-01-01

    This document establishes requirements and standard methods for the development and maintenance of the Emergency Management Hazards Assessment (EMHA) process used by the lead and all event contractors at the Y-12 Complex for emergency planning and preparedness. The EMHA process provides the technical basis for the Y-12 emergency management program. The instructions provided in this document include methods and requirements for performing the following emergency management activities at Y-12: (1) hazards identification; (2) hazards survey, and (3) hazards assessment

  14. Industrial process gamma tomography. Final report of a coordinated research project 2003-2007

    International Nuclear Information System (INIS)

    2008-05-01

    Gamma computed tomography (CT) is complementary to radiotracer and gamma sealed source techniques largely used for analyzing industrial process units. Relevant target areas for gamma CT applications are generally known. Although the methodology is generic and applicable across broad industrial specimen and facilities, a number of specific items have been identified as the most appropriate target beneficiaries of these applications: distillation columns; packed beds; risers; fluidized beds and other multiphase processing units. These industrial process units present significant technical challenges to CT investigations in terms of the complexity of the multiphase flows that occur in them. In order to address these needs, the IAEA implemented a Coordinated Research Project (CRP) on Industrial Process Gamma Tomography with the overall objective of testing and validating CT techniques for diagnosing industrial multiphase processes. CT laboratories from Argentina, Brazil, Czech Republic, France, Republic of Korea, Malaysia, Norway, Poland, United Kingdom and the United States of America have participated. The specific objectives of the CRP were assessment of the tomographic methods, evaluation of them for investigation of multiphase engineering processes, and design of prototypes of simple CT systems for industrial processing, which can be transferred to other developing countries. The CRP has generated an active network, which also included other groups engaged in the CT field. The round robin test has played an important role in validation of techniques and software. This TECDOC is prepared based on the findings and achievements of the CRP. It is a comprehensive technical report containing valuable information, not readily available in any single publication elsewhere. The participants' reports and software developed by them are compiled in a CD-ROM and attached to the back cover. The guidelines and software packages described in this report can be used as an

  15. Asset Management Process (AMP) Improvement Project: Final Report of Findings and Recommendations

    Science.gov (United States)

    2009-10-01

    Beach, Sue Meade-Lutz, Gary Reid, Deanna Tauvela, and Larry Majure . John Gorman served as the event’s Process Owner. INVESTIGATIONAL QUESTION The...Reid, Deanna Tauvela, and Larry Majure . John Gorman served as the event’s Process Owner. INVESTIGATIONAL QUESTION For years, the Center has...Provide custodians with receipts that are electronically tracked and use the receipt transaction to trigger forced asset transfers in ERP. See Appendix F

  16. Final workshop proceedings of the collaborative project ''Crystalline ROCK retention processes''

    Energy Technology Data Exchange (ETDEWEB)

    Rabung, Thomas; Garcia, David; Montoya Vanessa; Molinero, Jorge (eds.)

    2014-07-01

    The present document is the proceedings of the Final Workshop of the EURATOM FP7 Collaborative Project CROCK (Crystalline Rock Retention Processes). The key driver for initiation the CP CROCK, identified by national Waste Management Organizations, is the undesired high uncertainty and the associated conservatism with respect to the radionuclide transport in the crystalline host-rock far-field around geological disposal of high-level radioactive wastes.

  17. Geothermal absorption refrigeration for food processing industries. Final report, December 13, 1976--November 13, 1977

    Energy Technology Data Exchange (ETDEWEB)

    Harris, R.L.; Olson, G.K.; Mah, C.S.; Bujalski, J.H.

    1977-11-01

    The first step in the economic analysis of the integration of geothermally powered absorption refrigeration into a food processing plant was an evaluation of the potential geothermal sites in the Western United States. The evaluation covered availability of raw materials, transportation, adequate geothermal source, labor, and other requirements for food processing plants. Several attractive geothermal sites were identified--Raft River, Idaho; Sespe Hot Springs, California; Vale Hot Springs, Oregon; Weisler-Crane Creek, Idaho; Cosco Hot Springs, California; and the Imperial Valley, California. The most economically attractive food processing industry was then matched to the site based on its particular energy, raw material, and transportation requirements. The more promising food processors identified were for frozen potato or vegetable products, freeze-dried products, and meat processing. For the refrigeration temperature range of +32/sup 0/F to -40/sup 0/F and geothermal temperature range of 212/sup 0/F to 300/sup 0/F, an absorption refrigeration system had to be identified, designed, and evaluated. Both the conventional ammonia/water and an organic absorption refrigeration system using monochlorodifluoromethane (R-22) as the refrigerant and dimethyl formamide (DMF) as the absorbent were studied. In general, only a 60/sup 0/F to 100/sup 0/F temperature drop would be effectively used for refrigeration leaving the remainder of the allowable temperature drop available for other use. The economic evaluation of the geothermal system installed in a food processing plant required the comparison of several principal alternatives. These alternatives were evaluated for three different food processing plants located at their optimum geothermal site: a forzen potato product processing plant located at Raft River, Idaho; a freeze-dried product plant located at Sespe Hot Springs, California; a beef slaughter operation located in the Imperial Valley of California. (JGB)

  18. Final Report: "Collaborative Project. Understanding the Chemical Processes That Affect Growth Rates of Freshly Nucleated Particles"

    Energy Technology Data Exchange (ETDEWEB)

    Smith, James N. [NCAR, Boulder, CO (United States); McMurry, Peter H. [NCAR, Boulder, CO (United States)

    2015-11-12

    This final technical report describes our research activities that have, as the ultimate goal, the development of a model that explains growth rates of freshly nucleated particles. The research activities, which combine field observations with laboratory experiments, explore the relationship between concentrations of gas-phase species that contribute to growth and the rates at which those species are taken up. We also describe measurements of the chemical composition of freshly nucleated particles in a variety of locales, as well as properties (especially hygroscopicity) that influence their effects on climate. Our measurements include a self-organized, DOE-ARM funded project at the Southern Great Plains site, the New Particle Formation Study (NPFS), which took place during spring 2013. NPFS data are available to the research community on the ARM data archive, providing a unique suite observations of trace gas and aerosols that are associated with the formation and growth of atmospheric aerosol particles.

  19. Foaming and Antifoaming and Gas Entrainment in Radioactive Waste Pretreatment and Immobilization Processes. Final Report

    International Nuclear Information System (INIS)

    Wasan, Darsh T.

    2007-01-01

    The Savannah River Site (SRS) and Hanford site are in the process of stabilizing millions of gallons of radioactive waste slurries remaining from production of nuclear materials for the Department of Energy (DOE). The Defense Waste Processing Facility (DWPF) at SRS is currently vitrifying the waste in borosilicate glass, while the facilities at the Hanford site are in the construction phase. Both processes utilize slurry-fed joule-heated melters to vitrify the waste slurries. The DWPF has experienced difficulty during operations. The cause of the operational problems has been attributed to foaming, gas entrainment and the rheological properties of the process slurries. The rheological properties of the waste slurries limit the total solids content that can be processed by the remote equipment during the pretreatment and meter feed processes. Highly viscous material can lead to air entrainment during agitation and difficulties with pump operations. Excessive foaming in waste evaporators can cause carryover of radionuclides and non-radioactive waste to the condensate system. Experimental and theoretical investigations of the surface phenomena, suspension rheology and bubble generation of interactions that lead to foaming and air entrainment problems in the DOE High Level and Low Activity Radioactive Waste separation and immobilization processes were pursued under this project. The first major task accomplished in the grant proposal involved development of a theoretical model of the phenomenon of foaming in a three-phase gas-liquid-solid slurry system. This work was presented in a recently completed Ph.D. thesis (9). The second major task involved the investigation of the inter-particle interaction and microstructure formation in a model slurry by the batch sedimentation method. Both experiments and modeling studies were carried out. The results were presented in a recently completed Ph.D. thesis. The third task involved the use of laser confocal microscopy to study

  20. St. Louis demonstration final report: refuse processing plant equipment, facilities, and environmental evaluations

    Energy Technology Data Exchange (ETDEWEB)

    Fiscus, D.E.; Gorman, P.G.; Schrag, M.P.; Shannon, L.J.

    1977-09-01

    The results are presented of processing plant evaluations of the St. Louis-Union Electric Refuse Fuel Project, including equipment and facilities as well as assessment of environmental emissions at both the processing and the power plants. Data on plant material flows and operating parameters, plant operating costs, characteristics of plant material flows, and emissions from various processing operations were obtained during a testing program encompassing 53 calendar weeks. Refuse derived fuel (RDF) is the major product (80.6% by weight) of the refuse processing plant, the other being ferrous metal scrap, a marketable by-product. Average operating costs for the entire evaluation period were $8.26/Mg ($7.49/ton). The average overall processing rate for the period was 168 Mg/8-h day (185.5 tons/8-h day) at 31.0 Mg/h (34.2 tons/h). Future plants using an air classification system of the type used at the St. Louis demonstration plant will need an emissions control device for particulates from the large de-entrainment cyclone. Also in the air exhaust from the cyclone were total counts of bacteria and viruses several times higher than those of suburban ambient air. No water effluent or noise exposure problems were encountered, although landfill leachate mixed with ground water could result in contamination, given low dilution rates.

  1. Engineering evaluation of selective ion-exchange radioactive waste processing at Susquehanna Nuclear Power Plant: Final report

    International Nuclear Information System (INIS)

    Vance, J.N.

    1989-01-01

    This final report describes the work performed of an engineering feasibility evaluation of the use and benefits of a selective ion exchange treatment process in the Susquehanna radwaste system. The evaluation addressed operability and processing capability concerns, radiological impacts of operating in the radwaste discharge mode, required hardware modifications to the radwaste and plant make-up systems, impacts on plant water quality limits and impacts on higher waste classifications. An economic analysis is also reported showing the economic benefit of the use of selective ion exchange. 1 ref., 4 figs., 13 tabs

  2. Waste Receiving and Processing (WRAP) Facility Final Safety Analysis Report (FSAR)

    International Nuclear Information System (INIS)

    TOMASZEWSKI, T.A.

    2000-01-01

    The Waste Receiving and Processing Facility (WRAP), 2336W Building, on the Hanford Site is designed to receive, confirm, repackage, certify, treat, store, and ship contact-handled transuranic and low-level radioactive waste from past and present U.S. Department of Energy activities. The WRAP facility is comprised of three buildings: 2336W, the main processing facility (also referred to generically as WRAP); 2740W, an administrative support building; and 2620W, a maintenance support building. The support buildings are subject to the normal hazards associated with industrial buildings (no radiological materials are handled) and are not part of this analysis except as they are impacted by operations in the processing building, 2336W. WRAP is designed to provide safer, more efficient methods of handling the waste than currently exist on the Hanford Site and contributes to the achievement of as low as reasonably achievable goals for Hanford Site waste management

  3. Waste Receiving and Processing (WRAP) Facility Final Safety Analysis Report (FSAR)

    Energy Technology Data Exchange (ETDEWEB)

    TOMASZEWSKI, T.A.

    2000-04-25

    The Waste Receiving and Processing Facility (WRAP), 2336W Building, on the Hanford Site is designed to receive, confirm, repackage, certify, treat, store, and ship contact-handled transuranic and low-level radioactive waste from past and present U.S. Department of Energy activities. The WRAP facility is comprised of three buildings: 2336W, the main processing facility (also referred to generically as WRAP); 2740W, an administrative support building; and 2620W, a maintenance support building. The support buildings are subject to the normal hazards associated with industrial buildings (no radiological materials are handled) and are not part of this analysis except as they are impacted by operations in the processing building, 2336W. WRAP is designed to provide safer, more efficient methods of handling the waste than currently exist on the Hanford Site and contributes to the achievement of as low as reasonably achievable goals for Hanford Site waste management.

  4. Final Technical Report - Autothermal Styrene Manufacturing Process with Net Export of Energy

    Energy Technology Data Exchange (ETDEWEB)

    Trubac, Robert , E.; Lin, Feng; Ghosh, Ruma: Greene, Marvin

    2011-11-29

    The overall objectives of the project were to: (a) develop an economically competitive processing technology for styrene monomer (SM) that would reduce process energy requirements by a minimum 25% relative to those of conventional technology while achieving a minimum 10% ROI; and (b) advance the technology towards commercial readiness. This technology is referred to as OMT (Oxymethylation of Toluene). The unique energy savings feature of the OMT technology would be replacement of the conventional benzene and ethylene feedstocks with toluene, methane in natural gas and air or oxygen, the latter of which have much lower specific energy of production values. As an oxidative technology, OMT is a net energy exporter rather than a net energy consumer like the conventional ethylbenzene/styrene (EB/SM) process. OMT plants would ultimately reduce the cost of styrene monomer which in turn will decrease the costs of polystyrene making it perhaps more cost competitive with competing polymers such as polypropylene.

  5. Priority listing of industrial processes by total energy consumption and potential for savings. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Streb, A.J.

    1977-01-01

    A survey of eight of the most energy-intensive segments of the U.S. industry is made to quantify the energy consumed in the principal process units, to identify areas in which significant improvement appear possible, and to rank the process units in terms of total energy consumption and the potential for improvement. Data on the steel, paper, aluminum, textile, cement, and glass industries, petroleum refineries, and olefins and derivative products industries were compiled to help plan the development of new energy sources and to provide targets for energy conservation activities. (MCW)

  6. In-Situ Real Time Monitoring and Control of Mold Making and Filling Processes: Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Mohamed Abdelrahman; Kenneth Currie

    2010-12-22

    This project presents a model for addressing several objectives envisioned by the metal casting industries through the integration of research and educational components. It provides an innovative approach to introduce technologies for real time characterization of sand molds, lost foam patterns and monitoring of the mold filling process. The technology developed will enable better control over the casting process. It is expected to reduce scrap and variance in the casting quality. A strong educational component is integrated into the research plan to utilize increased awareness of the industry professional, the potential benefits of the developed technology, and the potential benefits of cross cutting technologies.

  7. Scale Up of Malonic Acid Fermentation Process: Cooperative Research and Development Final Report, CRADA Number CRD-16-612

    Energy Technology Data Exchange (ETDEWEB)

    Schell, Daniel J [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2018-04-16

    The goal of this work is to use the large fermentation vessels in the National Renewable Energy Laboratory's (NREL) Integrated Biorefinery Research Facility (IBRF) to scale-up Lygos' biological-based process for producing malonic acid and to generate performance data. Initially, work at the 1 L scale validated successful transfer of Lygos' fermentation protocols to NREL using a glucose substrate. Outside of the scope of the CRADA with NREL, Lygos tested their process on lignocellulosic sugars produced by NREL at Lawrence Berkeley National Laboratory's (LBNL) Advanced Biofuels Process Development Unit (ABPDU). NREL produced these cellulosic sugar solutions from corn stover using a separate cellulose/hemicellulose process configuration. Finally, NREL performed fermentations using glucose in large fermentors (1,500- and 9,000-L vessels) to intermediate product and to demonstrate successful performance of Lygos' technology at larger scales.

  8. Approaches and practices related to hazardous waste management, processing and final disposal in germany and Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Passos, J.A.L.; Pereira, F.A.; Tomich, S. [CETREL S.A., Camacari, BA (Brazil)

    1993-12-31

    A general overview of the existing management and processing of hazardous wastes technologies in Germany and Brazil is presented in this work. Emphasis has been given to the new technologies and practices adopted in both countries, including a comparison of the legislation, standards and natural trends. Two case studies of large industrial hazardous waste sites are described. 9 refs., 2 figs., 9 tabs.

  9. Impact of the Diagnostic Process on Parents of Infants and Preschool Children. Final Report.

    Science.gov (United States)

    Tice, Terrence N.; Hanson, Janice L.

    In an investigation of the impact of the psychological/educational diagnostic process on the parents of young children at risk for developmental delay, 18 families completed questionnaires and were interviewed concerning their child's evaluation. Transcribed interviews conducted 1-2 weeks after the evaluation and 4 months after the evaluations…

  10. Utilization of geothermal energy in the mining and processing of tungsten ore. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Erickson, M.V.; Lacy, S.B.; Lowe, G.D.; Nussbaum, A.M.; Walter, K.M.; Willens, C.A.

    1981-01-01

    The engineering, economic, and environmental feasibility of the use of low and moderate temperature geothermal heat in the mining and processing of tungsten ore is explored. The following are covered: general engineering evaluation, design of a geothermal energy system, economics, the geothermal resource, the institutional barriers assessment, environmental factors, an alternate geothermal energy source, and alternates to geothermal development. (MHR)

  11. Human-system interface design review guideline -- Process and guidelines: Final report. Revision 1, Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    None

    1996-06-01

    NUREG-0700, Revision 1, provides human factors engineering (HFE) guidance to the US Nuclear Regulatory Commission staff for its: (1) review of the human system interface (HSI) design submittals prepared by licensees or applications for a license or design certification of commercial nuclear power plants, and (2) performance of HSI reviews that could be undertaken as part of an inspection or other type of regulatory review involving HSI design or incidents involving human performance. The guidance consists of a review process and HFE guidelines. The document describes those aspects of the HSI design review process that are important to the identification and resolution of human engineering discrepancies that could adversely affect plant safety. Guidance is provided that could be used by the staff to review an applicant`s HSI design review process or to guide the development of an HSI design review plan, e.g., as part of an inspection activity. The document also provides detailed HFE guidelines for the assessment of HSI design implementations. NUREG-0700, Revision 1, consists of three stand-alone volumes. Volume 1 consists of two major parts. Part 1 describes those aspects of the review process of the HSI design that are important to identifying and resolving human engineering discrepancies. Part 2 contains detailed guidelines for a human factors engineering review which identify criteria for assessing the implementation of an applicant`s or licensee`s HSI design.

  12. Automatic Processing of Metallurgical Abstracts for the Purpose of Information Retrieval. Final Report.

    Science.gov (United States)

    Melton, Jessica S.

    Objectives of this project were to develop and test a method for automatically processing the text of abstracts for a document retrieval system. The test corpus consisted of 768 abstracts from the metallurgical section of Chemical Abstracts (CA). The system, based on a subject indexing rational, had two components: (1) a stored dictionary of words…

  13. The Multi-Isotope Process (MIP) Monitor Project: FY13 Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Meier, David E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Coble, Jamie B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jordan, David V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Mcdonald, Luther W. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Forrester, Joel B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Schwantes, Jon M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Unlu, Kenan [Pennsylvania State Univ., University Park, PA (United States); Landsberger, Sheldon [Univ. of Texas, Austin, TX (United States); Bender, Sarah [Pennsylvania State Univ., University Park, PA (United States); Dayman, Kenneth J. [Univ. of Texas, Austin, TX (United States); Reilly, Dallas D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2013-09-01

    The Multi-Isotope Process (MIP) Monitor provides an efficient approach to monitoring the process conditions in reprocessing facilities in support of the goal of “… (minimization of) the risks of nuclear proliferation and terrorism.” The MIP Monitor measures the distribution of the radioactive isotopes in product and waste streams of a nuclear reprocessing facility. These isotopes are monitored online by gamma spectrometry and compared, in near-real-time, to spectral patterns representing “normal” process conditions using multivariate analysis and pattern recognition algorithms. The combination of multivariate analysis and gamma spectroscopy allows us to detect small changes in the gamma spectrum, which may indicate changes in process conditions. By targeting multiple gamma-emitting indicator isotopes, the MIP Monitor approach is compatible with the use of small, portable, relatively high-resolution gamma detectors that may be easily deployed throughout an existing facility. The automated multivariate analysis can provide a level of data obscurity, giving a built-in information barrier to protect sensitive or proprietary operational data. Proof-of-concept simulations and experiments have been performed in previous years to demonstrate the validity of this tool in a laboratory setting for systems representing aqueous reprocessing facilities. However, pyroprocessing is emerging as an alternative to aqueous reprocessing techniques.

  14. Process for final storage of high level radioactive fission product solution

    International Nuclear Information System (INIS)

    Ellis, J.R.B.; Fries, B.A.

    1984-01-01

    In this process for the storage of an aqueous solution of radioactive nuclides, the solution is diluted with system water, which is obtained from a reservoir below the bottom of the sea in a porous geological stratum. After dilution, the diluted solution is injected into the same geological stratum under the bottom of the sea. (orig.) [de

  15. California Food Processing Industry Wastewater Demonstration Project: Phase I Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Lewis, Glen; Atkinson, Barbara; Rhyne, Ivin

    2009-09-09

    Wastewater treatment is an energy-intensive process and electricity demand is especially high during the utilities summer peak electricity demand periods. This makes wastewater treatment facilities prime candidates for demand response programs. However, wastewater treatment is often peripheral to food processing operations and its demand response opportunities have often been overlooked. Phase I of this wastewater demonstration project monitored wastewater energy and environmental data at Bell-Carter Foods, Inc., California's largest olive processing plant. For this monitoring activity the project team used Green Energy Management System (GEMS) automated enterprise energy management (EEM) technologies. This report presents results from data collected by GEMS from September 15, 2008 through November 30, 2008, during the olive harvest season. This project established and tested a methodology for (1) gathering baseline energy and environmental data at an industrial food-processing plant and (2) using the data to analyze energy efficiency, demand response, daily peak load management, and environmental management opportunities at the plant. The Phase I goals were to demonstrate the measurement and interrelationship of electricity demand, electricity usage, and water quality metrics and to estimate the associated CO{sub 2} emissions.

  16. Advanced safeguards systems development for chemical processing plants. Final report for Fiscal Year 1979

    International Nuclear Information System (INIS)

    Johnson, C.E.

    1980-01-01

    A computer system is being installed by INEL to test and evaluate safeguards monitoring concepts in an operating nuclear fuel processing plant. Safeguards development sensors and instruments installed in the ICPP provide plant information to a computer data acquisition and analysis system. Objective of the system is to collect data from process and safeguards sensors and show how this data can be analyzed to detect diversion operations or improper plant operation, and to test the performance of the monitoring devices. Approximately one-third of the installation designs and one-eighth of the installations were completed in FY 1979. The ICPP processing schedule for FY 1980 permits installation of the remaining monitoring devices before process startup in the fourth quarter of FY 1980. All computer hardware was delivered and checked out in FY 1979. Computer software system designs were completed with the majority of the programming scheduled for FY 1980. Sensor and instrument development in FY 1979 emphasized device testing for ICPP monitoring applications

  17. Approaches and practices related to hazardous waste management, processing and final disposal in germany and Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Passos, J A.L.; Pereira, F A; Tomich, S [CETREL S.A., Camacari, BA (Brazil)

    1994-12-31

    A general overview of the existing management and processing of hazardous wastes technologies in Germany and Brazil is presented in this work. Emphasis has been given to the new technologies and practices adopted in both countries, including a comparison of the legislation, standards and natural trends. Two case studies of large industrial hazardous waste sites are described. 9 refs., 2 figs., 9 tabs.

  18. STS-112 final main engine is installed after welding/polishing process

    Science.gov (United States)

    2002-01-01

    KENNEDY SPACE CENTER, FLA. -- The last engine is installed in orbiter Atlantis after a welding and polishing process was undertaken on flow liners where cracks were detected. All engines were removed for inspection of flow liners. Atlantis will next fly on mission STS-112, scheduled for launch no earlier than Oct. 2.

  19. Final Report Collaborative Project. Improving the Representation of Coastal and Estuarine Processes in Earth System Models

    Energy Technology Data Exchange (ETDEWEB)

    Bryan, Frank [National Center for Atmospheric Research, Boulder, CO (United States); Dennis, John [National Center for Atmospheric Research, Boulder, CO (United States); MacCready, Parker [Univ. of Washington, Seattle, WA (United States); Whitney, Michael [Univ. of Connecticut

    2015-11-20

    This project aimed to improve long term global climate simulations by resolving and enhancing the representation of the processes involved in the cycling of freshwater through estuaries and coastal regions. This was a collaborative multi-institution project consisting of physical oceanographers, climate model developers, and computational scientists. It specifically targeted the DOE objectives of advancing simulation and predictive capability of climate models through improvements in resolution and physical process representation. The main computational objectives were: 1. To develop computationally efficient, but physically based, parameterizations of estuary and continental shelf mixing processes for use in an Earth System Model (CESM). 2. To develop a two-way nested regional modeling framework in order to dynamically downscale the climate response of particular coastal ocean regions and to upscale the impact of the regional coastal processes to the global climate in an Earth System Model (CESM). 3. To develop computational infrastructure to enhance the efficiency of data transfer between specific sources and destinations, i.e., a point-to-point communication capability, (used in objective 1) within POP, the ocean component of CESM.

  20. Solar feasibility study for site-specific industrial-process-heat applications. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Murray, O.L.

    1980-03-18

    This study addresses the technical feasibility of solar energy in industrial process heat (IPH) applications in Mid-America. The study was one of two contracted efforts covering the MASEC 12-state region comprised of: Illinois, Michigan, North Dakota, Indiana, Minnesota, Ohio, Iowa, Missouri, South Dakota, Kansas, Nebraska, Wisconsin. The results of our study are encouraging to the potential future role of solar energy in supplying process heat to a varied range of industries and applications. We identified and developed Case Study documentation of twenty feasible solar IPH applications covering eight major SIC groups within the Mid-American region. The geographical distribution of these applications for the existing range of solar insolation levels are shown and the characteristics of the applications are summarized. The results of the study include process identification, analysis of process heat requirements, selection of preliminary solar system characteristics, and estimation of system performance and cost. These are included in each of the 20 Case Studies. The body of the report is divided into two primary discussion sections dealing with the Study Methodology employed in the effort and the Follow-On Potential of the identified applications with regard to possible demonstration projects. The 20 applications are rated with respect to their relative overall viability and procedures are discussed for possible demonstration project embarkment. Also, a possible extension of this present feasibility study for late-comer industrial firms expressing interest appears worthy of consideration.

  1. Human-system interface design review guideline -- Process and guidelines: Final report. Revision 1, Volume 1

    International Nuclear Information System (INIS)

    1996-06-01

    NUREG-0700, Revision 1, provides human factors engineering (HFE) guidance to the US Nuclear Regulatory Commission staff for its: (1) review of the human system interface (HSI) design submittals prepared by licensees or applications for a license or design certification of commercial nuclear power plants, and (2) performance of HSI reviews that could be undertaken as part of an inspection or other type of regulatory review involving HSI design or incidents involving human performance. The guidance consists of a review process and HFE guidelines. The document describes those aspects of the HSI design review process that are important to the identification and resolution of human engineering discrepancies that could adversely affect plant safety. Guidance is provided that could be used by the staff to review an applicant's HSI design review process or to guide the development of an HSI design review plan, e.g., as part of an inspection activity. The document also provides detailed HFE guidelines for the assessment of HSI design implementations. NUREG-0700, Revision 1, consists of three stand-alone volumes. Volume 1 consists of two major parts. Part 1 describes those aspects of the review process of the HSI design that are important to identifying and resolving human engineering discrepancies. Part 2 contains detailed guidelines for a human factors engineering review which identify criteria for assessing the implementation of an applicant's or licensee's HSI design

  2. Process and analytical studies of enhanced low severity co-processing using selective coal pretreatment. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    Baldwin, R.M.; Miller, R.L.

    1991-12-01

    The findings in the first phase were as follows: 1. Both reductive (non-selective) alkylation and selective oxygen alkylation brought about an increase in liquefaction reactivity for both coals. 2. Selective oxygen alkylation is more effective in enhancing the reactivity of low rank coals. In the second phase of studies, the major findings were as follows: 1. Liquefaction reactivity increases with increasing level of alkylation for both hydroliquefaction and co-processing reaction conditions. 2. the increase in reactivity found for O-alkylated Wyodak subbituminous coal is caused by chemical changes at phenolic and carboxylic functional sites. 3. O-methylation of Wyodak subbituminous coal reduced the apparent activation energy for liquefaction of this coal.

  3. Decommissioning of the MTR-605 process water building at the Idaho National Engineering Laboratory. Final report

    International Nuclear Information System (INIS)

    Browder, J.H.; Wills, E.L.

    1985-01-01

    Decontamination and decommissioning (D and D) of the unused radioactively contaminated portions of the MTR-605 building at the Test Reactor Area of the Idaho National Engineering Laboratory has been completed; this final report describes the D and D project. The building is a two-story concrete structure that was used to house piping systems to channel and control coolant water flow for the Materials Testing Reactor (MTR), a 40 MW (thermal) light water test reactor that was operated from 1952 until 1970 and then deactivated. D and D project objectives were to reduce potential environmental and radioactive contamination hazards to levels as low a reasonably achievable. Primary tasks of the D and D project were: to remove contaminated piping (about 400 linear ft of 36- and 30-in.-dia stainless steel pipe) and valves from the primary coolant pipe tunnels, to remove a primary coolant pump and piping, and to remove the three 8-ft-dia by 25-ft-long evaporators from the building second floor

  4. Rejection Sensitivity Moderates the Impact of Rejection on Self-Concept Clarity

    Science.gov (United States)

    Ayduk, Özlem; Gyurak, Anett; Luerssen, Anna

    2014-01-01

    Self-concept clarity (SCC) refers to the extent to which self-knowledge is clearly and confidently defined, internally consistent, and temporally stable. Research shows that SCC can be undermined by failures in valued goal domains. Because preventing rejection is an important self-relevant goal for people high in rejection sensitivity (RS), it is hypothesized here that failures to attain this goal would cause them to experience diminished SCC. Study 1, an experimental study, showed that high-RS people’s SCC was undermined following rejection but not following an aversive experience unrelated to rejection. Study 2, a daily diary study of couples in relationships, used occurrence of partner conflicts to operationalize rejection. Replicating the findings in Study 1, having a conflict on any given diary day predicted a greater reduction in the SCC of high- compared to low-RS people on the following day. The implications for understanding the conditions under which rejection negatively affects the self-concept are discussed. PMID:19713567

  5. Final Report Appendices. Preliminary Process and Market Evaluation. Better Buildings Neighborhood Program

    Energy Technology Data Exchange (ETDEWEB)

    Peters, Jane S. [Research Into Action, NMR Group, Inc., Portland, OR (United States)

    2012-12-28

    This document was prepared as an account of work sponsored by an agency of the United States government. Neither the United States government nor any agency thereof, nor any of their employees, makes any warranty, express or implied, or assumes any legal liability or responsibility for the accuracy, completeness, usefulness, or any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights. Reference herein to any specific commercial product, process, or service by trade name, trademark, manufacturer, or otherwise does not necessarily constitute or imply its endorsement, re commendation, or favoring by the United States government or any agency thereof. The views and opinions of authors expressed herein do not necessarily state or reflect those of the United States government or any agency thereof.

  6. United States Department of Energy Integrated Manufacturing & Processing Predoctoral Fellowships. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Petrochenkov, M.

    2003-03-31

    The objective of the program was threefold: to create a pool of PhDs trained in the integrated approach to manufacturing and processing, to promote academic interest in the field, and to attract talented professionals to this challenging area of engineering. It was anticipated that the program would result in the creation of new manufacturing methods that would contribute to improved energy efficiency, to better utilization of scarce resources, and to less degradation of the environment. Emphasis in the competition was on integrated systems of manufacturing and the integration of product design with manufacturing processes. Research addressed such related areas as aspects of unit operations, tooling and equipment, intelligent sensors, and manufacturing systems as they related to product design.

  7. Laser Materials Processing Final Report CRADA No. TC-1526-98

    Energy Technology Data Exchange (ETDEWEB)

    Crane, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Lehane, C. J. [United Technologies Corp., East Hartford, CT (United States)

    2017-09-08

    This CRADA project was a joint effort between Lawrence Livermore National Laboratory (LLNL) and United Technologies Corporation (UTC)/Pratt & Whitney (P&W) to demonstrate process capability for drilling holes in turbine airfoils using LLNL-developed femtosecond laser machining technology. The basis for this development was the ability of femtosecond lasers to drill precision holes in variety of materials with little or no collateral damage. The ultimate objective was to develop a laser machine tool consisting of an extremely advanced femtosecond laser subsystem to be developed by LLNL on a best-effort basis and a drilling station for turbine blades and vanes to be developed by P&W. In addition, P&W was responsible for commercializing the system. The goal of the so called Advanced Laser Drilling (ALD) system was to drill specified complex hole-shapes in turbine blades and vanes with a high degree precision and repeatability and simultaneously capable of very high speed processing.

  8. Summary of research on microbiological processes. International Energy Agency Subtask D, final report

    Energy Technology Data Exchange (ETDEWEB)

    Winters, A.L.

    1992-09-01

    Storage of thermal energy in aquifers has obvious benefits of saving energy and decreasing the consumption of fossil fuels. However, aquifer thermal energy storage (ATES), which involves groundwater aquifers as the storage medium for heat or chill, impinges on the environment. A literature review of pertinent microbiology publications (Hicks and Stewart, 1988) identified the potential for the interaction of ATES systems and microbiological processes to create a source of infectious diseases and the potential for damage to the environment. In addition, the review identified a potential for microbiological processes to develop conditions that would interfere with the operation of an ATES system. As a result of this research effort, investigators from Finland, Germany, Switzerland, and the United States have examined several ATES systems in operation and have observed that the ATES systems studied do not contribute to infectious disease transmission, do not adversely affect the environment, and do not contribute significantly to biofouling or biocorrosion.

  9. Beneficiation of limestone plant rejects for value addition.

    Science.gov (United States)

    Jena, M S; Sahu, P; Dash, P; Mohanty, J K

    2013-11-15

    Investigations were carried out on lime stone rejects (-1mm) generated at a lime stone washing plant in southern India. These rejects contain 12.09% CaO, 2.95% MgO, 10.73% Al2O3, 4.99% Fe2O3, 43.05% SiO2 and 24.92% LOI. Mineralogical studies including SEM-EDAX, XRD, FTIR and TGA were conducted to confirm relative distribution of minerals in the flotation feed and products. These studies revealed that feed sample consists of quartz and calcite as the major minerals with minor amounts of montmorillonite and dolomite whereas flotation concentrate dominantly consists of calcite, and tailings mostly of quartz and montmorillonite. A commercial grade sodium silicate, oleic acid and MIBC were used as depressant, collector and frother respectively in flotation studies. The effects of different operating parameters were evaluated for both conventional and column flotation. Two stage conventional cell flotation results indicate that a cleaner concentrate of 42.50% lime (CaO) content could be obtained at a yield of 15.65%. The lime (CaO) content of the concentrate was further enhanced up to 44.23% at 20.73% yield using single stage column flotation. The column flotation is more efficient in comparison to the conventional cell for treating this sample. A process flowsheet was developed to treat these rejects based on the studies carried out. This process can minimize the waste generation and the concentrate generated during this process can be directly utilized in the Indian cement industries. Copyright © 2013 Elsevier B.V. All rights reserved.

  10. Analysis of ex situ processes of CO2 sequestration. Final report

    International Nuclear Information System (INIS)

    Touze, S.; Bourgeois, F.; Baranger, P.; Durst, P.

    2004-01-01

    The aim of this study is to bring quantitative elements to evaluate the validation of the CO 2 mineral sequestration to limit the greenhouse effect gases. This analysis aims to calculate the CO 2 accounting of the system (internal energy production balance the energy expend) sequestrated CO 2 and produced CO 2 . The first part detailed the possible experimental solutions. Then two carbonation processes, direct and indirect, have been chosen of the analysis. (A.L.B.)

  11. Acidic deposition: State of science and technology. Report 2. Atmospheric processes research and process model development. Final report

    International Nuclear Information System (INIS)

    Hicks, B.B.; Draxler, R.R.; Albritton, D.L.; Fehsenfeld, F.C.; Davidson, C.I.

    1990-10-01

    The document represents an attempt to put together, in one place, a summary of the present state of knowledge concerning those processes that affect air concentrations of acidic and acidifying pollutants, during their transport, from emission to deposition. It is not intended to be an all-encompassing review of the entire breadth of each of the contributing disciplines, but instead focuses on those areas where the state of science has improved over the last decade--the period of the National Acid Precipitation Assessment Program. The discussion is not limited to NAPAP activities, although it is clear that the products of NAPAP research are perhaps given greater attention than are the results obtained elsewhere. This bias is partially intentional, since it is the INTEGRATED ASSESSMENT that is currently being prepared by NAPAP that constitutes the 'client' for the material presented here. The integrated assessment pay attention to the North American situation alone, and hence the present work gives greatest attention to the North American case, but with awareness of the need to place this particular situation in the context of the rest of the world

  12. Development and application of a probabilistic evaluation method for advanced process technologies. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Frey, H.C.; Rubin, E.S.

    1991-04-01

    The objective of this work is to develop and apply a method for research planning for advanced process technologies. To satisfy requirements for research planning, it is necessary to: (1) identify robust solutions to process design questions in the face of uncertainty to eliminate inferior design options; (2) identify key problem areas in a technology that should be the focus of further research to reduce the risk of technology failure; (3) compare competing technologies on a consistent basis to determine the risks associated with adopting a new technology; and (4) evaluate the effects that additional research might have on comparisons with conventional technology. An important class of process technologies are electric power plants. In particular, advanced clean coal technologies are expected to play a key role in the energy and environmental future of the US, as well as in other countries. Research planning for advanced clean coal technology development is an important part of energy and environmental policy. Thus, the research planning method developed here is applied to case studies focusing on a specific clean coal technology. The purpose of the case studies is both to demonstrate the research planning method and to obtain technology-specific conclusions regarding research strategies.

  13. Post-Lamination Manufacturing Process Automation for Photovoltaic Modules: Final Subcontract Report, April 1998 - April 2002

    Energy Technology Data Exchange (ETDEWEB)

    Nowlan, M. J.; Murach, J. M.; Sutherland, S. F.; Miller, D. C.; Moore, S. B.; Hogan, S. J.

    2002-11-01

    This report describes the automated systems developed for PV module assembly and testing processes after lamination. These processes are applicable to a broad range of module types, including those made with wafer-based and thin-film solar cells. Survey data and input from module manufacturers gathered during site visits were used to define system capabilities and process specifications. Spire completed mechanical, electrical, and software engineering for four automation systems: a module edge trimming system, the SPI-TRIM 350; an edge sealing and framing system, the SPI-FRAMER 350; an integrated module testing system, the SPI-MODULE QA 350; and a module buffer storage system, the SPI-BUFFER 350. A fifth system for junction-box installation, the SPI-BOXER 350, was nearly completed during the program. A new-size solar simulator, the SPI-SUN SIMULATOR 350i, was designed as part of the SPI-MODULE QA 350. This simulator occupies minimal production floor space, and its test area is large enough to handle most production modules. The automated systems developed in this program are designed for integration to create automated production lines.

  14. CP-violating Majorana phases, lepton-conserving processes, and final state interactions

    International Nuclear Information System (INIS)

    Nieves, Jose F.; Pal, Palash B.

    2003-01-01

    The CP-violating phases associated with Majorana neutrinos can give rise to CP-violating effects even in processes that conserve total lepton number, such as μ→eee-bar, μe→ee, and others. After explaining the reasons that make this happen, we consider the calculation of the rates for a process of the form l a l b →l a l c and its conjugate l-bar a l-bar b →l-bar a l-bar c , where l a ,l b ,l c denote charged leptons of different flavors. In the context of the standard model with Majorana neutrinos, we show that the difference in the rates depends on such phases. Our calculations illustrate in detail the mechanics that operate behind the scene, and set the stage for carrying out the analogous, more complicated (as we explain) calculations for other processes such as μ→eee-bar and its conjugate

  15. Final Technical Report on Development of an Economic and Efficient Biodiesel production Process (NC)

    Energy Technology Data Exchange (ETDEWEB)

    Tirla, Cornelia [Univ. of North Carolina, Pembroke, NC (United States); Dooling, Thomas A. [Univ. of North Carolina, Pembroke, NC (United States); Smith, Rachel B. [Univ. of North Carolina, Pembroke, NC (United States); Shi, Xinyan [Univ. of North Carolina, Pembroke, NC (United States); Shahbazi, Abolghasem [North Carolina Agricultural and Technical State Univ., Greensboro, NC (United States)

    2014-03-19

    The Biofuels Team at The University of North Carolina at Pembroke and North Carolina A&T State University carried out a joint research project aimed at developing an efficient process to produce biodiesel. In this project, the team developed and tested various types of homogeneous and heterogeneous catalysts which could replace the conventionally used soluble potassium hydroxide catalyst which, traditionally, must be separated and disposed of at the end of the process. As a result of this screening, the homogeneous catalyst choline hydroxide was identified as a potential replacement for the traditional catalyst used in this process, potassium hydroxide, due to its decreased corrosiveness and toxicity. A large number of heterogeneous catalysts were produced and tested in order to determine the scaffold, ion type and ion concentration which would produce optimum yield of biodiesel. The catalyst with 12% calcium on Zeolite β was identified as being highly effective and optimal reaction conditions were identified. Furthermore, a packed bed reactor utilizing this type of catalyst was designed, constructed and tested in order to further optimize the process. An economic analysis of the viability of the project showed that the cost of an independent farmer to produce the fuelstock required to produce biodiesel exceeds the cost of petroleum diesel under current conditions and that therefore without incentives, farmers would not be able to benefit economically from producing their own fuel. An educational website on biodiesel production and analysis was produced and a laboratory experiment demonstrating the production of biodiesel was developed and implemented into the Organic Chemistry II laboratory curriculum at UNCP. Five workshops for local farmers and agricultural agents were held in order to inform the broader community about the various fuelstock available, their cultivation and the process and advantages of biodiesel use and production. This project fits both

  16. Fetal cardiac cine imaging using highly accelerated dynamic MRI with retrospective motion correction and outlier rejection.

    Science.gov (United States)

    van Amerom, Joshua F P; Lloyd, David F A; Price, Anthony N; Kuklisova Murgasova, Maria; Aljabar, Paul; Malik, Shaihan J; Lohezic, Maelene; Rutherford, Mary A; Pushparajah, Kuberan; Razavi, Reza; Hajnal, Joseph V

    2018-01-01

    Development of a MRI acquisition and reconstruction strategy to depict fetal cardiac anatomy in the presence of maternal and fetal motion. The proposed strategy involves i) acquisition and reconstruction of highly accelerated dynamic MRI, followed by image-based ii) cardiac synchronization, iii) motion correction, iv) outlier rejection, and finally v) cardiac cine reconstruction. Postprocessing entirely was automated, aside from a user-defined region of interest delineating the fetal heart. The method was evaluated in 30 mid- to late gestational age singleton pregnancies scanned without maternal breath-hold. The combination of complementary acquisition/reconstruction and correction/rejection steps in the pipeline served to improve the quality of the reconstructed 2D cine images, resulting in increased visibility of small, dynamic anatomical features. Artifact-free cine images successfully were produced in 36 of 39 acquired data sets; prolonged general fetal movements precluded processing of the remaining three data sets. The proposed method shows promise as a motion-tolerant framework to enable further detail in MRI studies of the fetal heart and great vessels. Processing data in image-space allowed for spatial and temporal operations to be applied to the fetal heart in isolation, separate from extraneous changes elsewhere in the field of view. Magn Reson Med 79:327-338, 2018. © 2017 The Authors Magnetic Resonance in Medicine published by Wiley Periodicals, Inc. on behalf of International Society for Magnetic Resonance in Medicine. This is an open access article under the terms of the Creative Commons Attribution License, which permits use, distribution and reproduction in any medium, provided the original work is properly cited. 2017 The Authors Magnetic Resonance in Medicine published by Wiley Periodicals, Inc. on behalf of International Society for Magnetic Resonance in Medicine.

  17. A new rejection of moral expertise.

    Science.gov (United States)

    Cowley, Christopher

    2005-01-01

    There seem to be two clearly-defined camps in the debate over the problem of moral expertise. On the one hand are the "Professionals", who reject the possibility entirely, usually because of the intractable diversity of ethical beliefs. On the other hand are the "Ethicists", who criticise the Professionals for merely stipulating science as the most appropriate paradigm for discussions of expertise. While the subject matter and methodology of good ethical thinking is certainly different from that of good clinical thinking, they argue, this is no reason for rejecting the possibility of a distinctive kind of expertise in ethics, usually based on the idea of good justification. I want to argue that both are incorrect, partly because of the reasons given by one group against the other, but more importantly because both neglect what is most distinctive about ethics: that it is personal in a very specific way, without collapsing into relativism.

  18. Investigation of Pore Scale Processes That Affect Soil Vapor Extraction. Final Technical Report EMSP 70045

    International Nuclear Information System (INIS)

    Valocchi, Albert J.; Werth, Charles W.; Webb, Andrew W.

    2004-01-01

    Dense nonaqueous phase liquid (DNAPL) contamination in the vadose zone is a significant problem at Department of Energy sites. Soil vapor extraction (SVE) is commonly used to remediate DNAPLs from the vadose zone. In most cases, a period of high recovery has been followed by a sustained period of low recovery. This behavior has been attributed to multiple processes including slow interphase mass transfer, retarded vapor phase transport, and diffusion from unswept zones of low permeability. This research project used a combination of laboratory experimentation and mathematical modeling to determine how these various processes interact to limit the removal of DNAPL components in heterogeneous porous media during SVE. Our results were applied to scenarios typical of the carbon tetrachloride spill zone at the Hanford Site. Our results indicate that: (a) the initial distribution of the spilled DNAPL (i.e., the spill-zone architecture) has a major influence upon the performance of any subsequent SVE operations; (b) while the pattern of higher and lower conductivity soil zones has an important impact upon spill zone architecture, soil moisture distribution plays an even larger role when there are large quantities of co-disposed waste-water (as in the Hanford scenario); (c) depending upon soil moisture dynamics, liquid DNAPL that is trapped by surrounding water is extremely difficult to remove by SVE; (d) natural barometric pumping can remove a large amount of the initial DNAPL mass for spills occurring close to the land surface, and hence the initial spilled inventory will be over-estimated if this process is neglected

  19. Scale-up of miscible flood processes for heterogeneous reservoirs. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Orr, F.M. Jr.

    1996-04-01

    Results of a wide-ranging investigation of the scaling of gas injection processes are reported. The research examines how the physical mechanisms at work during a gas injection project interact to determine process performance. In particular, the authors examine: the interactions of equilibrium phase behavior and two-phase flow that determine local displacement efficiency and minimum miscibility pressure, the combined effects of viscous fingering, gravity segregation and heterogeneity that control sweep efficiency in 2- and 3-dimensional porous media, the use of streamtube/streamline methods to create very efficient simulation technique for multiphase compositional displacements, the scaling of viscous, capillary and gravity forces for heterogeneous reservoirs, and the effects of the thin films and spreading behavior on three-phase flow. The following key results are documented: rigorous procedures for determination of minimum miscibility pressure (MMP) or minimum miscibility enrichment (MME) for miscibility have been developed for multicomponent systems; the complex dependence of MMP`s for nitrogen/methane floods on oil and injection gas composition observed experimentally is explained for the first time; the presence of layer-like heterogeneities strongly influences the interplay of gravity segregation and viscous fingering, as viscous fingers adapt to preferential flow paths and low permeability layers restrict vertical flow; streamtube/streamline simulation techniques are demonstrated for a variety of injection processes in 2 and 3 dimensions; quantitative scaling estimates for the transitions from capillary-dominated to gravity-dominated to viscous-dominated flows are reported; experimental results are given that demonstrate that high pressure CO{sub 2} can be used to generate low IFT gravity drainage in fractured reservoirs if fractures are suitably connected; and the effect of wetting and spreading behavior on three-phase flow is described. 209 refs.

  20. Rapid tooling for functional prototyping of metal mold processes. CRADA final report

    Energy Technology Data Exchange (ETDEWEB)

    Zacharia, T.; Ludtka, G.M.; Bjerke, M.A.; Gray, W.H.

    1997-12-01

    The overall scope of this endeavor was to develop an integrated computer system, running on a network of heterogeneous computers, that would allow the rapid development of tool designs, and then use process models to determine whether the initial tooling would have characteristics which produce the prototype parts. The major thrust of this program for ORNL was the definition of the requirements for the development of the integrated die design system with the functional purpose to link part design, tool design, and component fabrication through a seamless software environment. The principal product would be a system control program that would coordinate the various application programs and implement the data transfer so that any networked workstation would be useable. The overall system control architecture was to be required to easily facilitate any changes, upgrades, or replacements of the model from either the manufacturing end or the design criteria standpoint. The initial design of such a program is described in the section labeled ``Control Program Design``. A critical aspect of this research was the design of the system flow chart showing the exact system components and the data to be transferred. All of the major system components would have been configured to ensure data file compatibility and transferability across the Internet. The intent was to use commercially available packages to model the various manufacturing processes for creating the die and die inserts in addition to modeling the processes for which these parts were to be used. In order to meet all of these requirements, investigative research was conducted to determine the system flow features and software components within the various organizations contributing to this project. This research is summarized.

  1. Processes and parameters involved in modeling radionuclide transport from bedded salt repositories. Final report. Technical memorandum

    International Nuclear Information System (INIS)

    Evenson, D.E.; Prickett, T.A.; Showalter, P.A.

    1979-07-01

    The parameters necessary to model radionuclide transport in salt beds are identified and described. A proposed plan for disposal of the radioactive wastes generated by nuclear power plants is to store waste canisters in repository sites contained in stable salt formations approximately 600 meters below the ground surface. Among the principal radioactive wastes contained in these canisters will be radioactive isotopes of neptunium, americium, uranium, and plutonium along with many highly radioactive fission products. A concern with this form of waste disposal is the possibility of ground-water flow occurring in the salt beds and endangering water supplies and the public health. Specifically, the research investigated the processes involved in the movement of radioactive wastes from the repository site by groundwater flow. Since the radioactive waste canisters also generate heat, temperature is an important factor. Among the processes affecting movement of radioactive wastes from a repository site in a salt bed are thermal conduction, groundwater movement, ion exchange, radioactive decay, dissolution and precipitation of salt, dispersion and diffusion, adsorption, and thermomigration. In addition, structural changes in the salt beds as a result of temperature changes are important. Based upon the half-lives of the radioactive wastes, he period of concern is on the order of a million years. As a result, major geologic phenomena that could affect both the salt bed and groundwater flow in the salt beds was considered. These phenomena include items such as volcanism, faulting, erosion, glaciation, and the impact of meteorites. CDM reviewed all of the critical processes involved in regional groundwater movement of radioactive wastes and identified and described the parameters that must be included to mathematically model their behavior. In addition, CDM briefly reviewed available echniques to measure these parameters

  2. Necessary and Sufficient Process leading to Work Smart Standards. Final report

    International Nuclear Information System (INIS)

    1996-11-01

    The Necessary and Sufficient Process leading to Work Smart Standards is a Department of Energy initiative to assure adequate protection for workers, the public, and the environment. The Work Smart Standards initiative directs the Laboratory to develop a set of ES and H standards based on the work performed at the Laboratory and the hazards associated with the work. Berkeley Lab's set of Work Smart Standards includes required Federal, State and local laws and, additionally, national and international standards which represent the highest operating standards of industrial and commercial institutions

  3. Necessary and Sufficient Process leading to Work Smart Standards. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-11-01

    The Necessary and Sufficient Process leading to Work Smart Standards is a Department of Energy initiative to assure adequate protection for workers, the public, and the environment. The Work Smart Standards initiative directs the Laboratory to develop a set of ES and H standards based on the work performed at the Laboratory and the hazards associated with the work. Berkeley Lab`s set of Work Smart Standards includes required Federal, State and local laws and, additionally, national and international standards which represent the highest operating standards of industrial and commercial institutions.

  4. Cesium removal demonstration utilizing crystalline silicotitanate sorbent for processing Melton Valley Storage Tank supernate: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Walker, J.F. Jr.; Taylor, P.A.; Cummins, R.L. [and others

    1998-03-01

    This report provides details of the Cesium Removal Demonstration (CsRD), which was conducted at Oak Ridge National Laboratory (ORNL) on radioactive waste from the Melton Valley Storage Tanks. The CsRD was the first large-scale use of state-of-the-art sorbents being developed by private industry for the selective removal of cesium and other radionuclides from liquid wastes stored across the DOE complex. The crystalline silicotitanate sorbent used in the demonstration was chosen because of its effectiveness in laboratory tests using bench-scale columns. The demonstration showed that the cesium could be removed from the supernate and concentrated on a small-volume, solid waste form that would meet the waste acceptance criteria for the Nevada Test Site. During this project, the CsRD system processed > 115,000 L (30,000 gal) of radioactive supernate with minimal operational problems. Sluicing, drying, and remote transportation of the sorbent, which could not be done on a bench scale, were successfully demonstrated. The system was then decontaminated to the extent that it could be contact maintained with the use of localized shielding only. By utilizing a modular, transportable design and placement within existing facilities, the system can be transferred to different sites for reuse. The initial unit has now been removed from the process building and is presently being reinstalled for use in baseline operations at ORNL.

  5. UMTRA Surface Project management action process document. Final report: Revision 1

    International Nuclear Information System (INIS)

    1996-04-01

    A critical mission of the US Department of Energy (DOE) is the planning, implementation, and completion of environmental restoration (ER) programs at facilities that were operated by or in support of the former Atomic Energy Commission (AEC) from the late 1940s into the 1970s. Among these facilities are the 24 former uranium mill sites designed in the Uranium Mill Tailings Radiation Control Act (UMTRCA) of 1978 (42 USC section 7901 et seq.) Title 1 of the UMTRCA authorized the DOE to undertake remedial actions at these designated sites and associated vicinity properties (VP), which contain uranium mill tailings and other residual radioactive materials (RRM) derived from the processing sites. Title 2 of the UMTRCA addresses uranium mill sites that were licensed at the time the UMTRCA was enacted. Cleanup of these Title 2 sites is the responsibility of the licensees. The cleanup of the Title 1 sites has been split into two separate projects: the Surface Project, which deals with the mill buildings, tailings, and contaminated soils at the sites and VPs; and the Ground Water Project, which is limited to the contaminated ground water at the sites. This management action process (MAP) document discusses the Uranium Mill Tailings Remedial Action (UMTRA) Surface Project only; a separate MAP document has been prepared for the UMTRA Ground Water Project

  6. End-use matching for solar industrial process heat. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Brown, K.C.; Hooker, D.W.; Rabl, A.; Stadjuhar, S.A.; West, R.E.

    1980-01-01

    Because of the large energy demand of industry (37% of US demand) and the wide spectrum of temperatures at which heat is required, the industrial sector appears to be very suitable for the matching of solar thermal technology with industrial process heat (IPH) requirements. A methodology for end-use matching has been devised, complete with required data bases and an evaluation program PROSYS/ECONMAT. Six cities in the United States were selected for an analysis of solar applications to IPH. Typical process heat requirements for 70% of the industrial plants in each city were identified and evaluated in conjunction with meteorological and economic data for each site to determine lowest-cost solar systems for each application. The flexibility and scope of PROSYS/ECONMAT is shown in a variety of sensitivity studies that expand the results of the six-city analysis. Case studies of two industrial plants were performed to evaluate the end-use matching procedure; these results are reported.

  7. APPLICATIONS OF THERMAL ENERGY STORAGE TO WASTE HEAT RECOVERY IN THE FOOD PROCESSING INDUSTRY, Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Lundberg, W. L.; Christenson, James A.

    1979-07-31

    A project is discussed in which the possibilities for economical waste heat recovery and utilization in the food industry were examined. Waste heat availability and applications surveys were performed at two manufacturing plants engaged in low temperature (freezing) and high temperature (cooking, sterilizing, etc.) food processing. The surveys indicate usable waste heat is available in significant quantities which could be applied to existing, on-site energy demands resulting in sizable reductions in factory fuel and energy usage. At the high temperature plant, the energy demands involve the heating of fresh water for boiler make-up, for the food processes and for the daily clean-up operation. Clean-up poses an opportunity for thermal energy storage since waste heat is produced during the one or two production shifts of each working day while the major clean-up effort does not occur until food production ends. At the frozen food facility, the clean-up water application again exists and, in addition, refrigeration waste heat could also be applied to warm the soil beneath the ground floor freezer space. Systems to recover and apply waste heat in these situations were developed conceptually and thermal/economic performance predictions were obtained. The results of those studies indicate the economics of waste heat recovery can be attractive for facilities with high energy demand levels. Small factories, however, with relatively low energy demands may find the economics marginal although, percentagewise, the fuel and energy savings are appreciable.

  8. Surface and subsurface cleanup protocol for radionuclides, Gunnison, Colorado, UMTRA project processing site. Final [report

    Energy Technology Data Exchange (ETDEWEB)

    1993-09-01

    Surface and subsurface soil cleanup protocols for the Gunnison, Colorado, processing sits are summarized as follows: In accordance with EPA-promulgated land cleanup standards (40 CFR 192), in situ Ra-226 is to be cleaned up based on bulk concentrations not exceeding 5 and 15 pCi/g in 15-cm surface and subsurface depth increments, averaged over 100-m{sup 2} grid blocks, where the parent Ra-226 concentrations are greater than, or in secular equilibrium with, the Th-230 parent. A bulk interpretation of these EPA standards has been accepted by the Nuclear Regulatory Commission (NRC), and while the concentration of the finer-sized soil fraction less than a No. 4 mesh sieve contains the higher concentration of radioactivity, the bulk approach in effect integrates the total sample radioactivity over the entire sample mass. In locations where Th-230 has differentially migrated in subsoil relative to Ra-226, a Th-230 cleanup protocol has been developed in accordance with Supplemental Standard provisions of 40 CFR 192 for NRC/Colorado Department of Health (CDH) approval for timely implementation. Detailed elements of the protocol are contained in Appendix A, Generic Protocol from Thorium-230 Cleanup/Verification at UMTRA Project Processing Sites. The cleanup of other radionuclides or nonradiological hazards that pose a significant threat to the public and the environment will be determined and implemented in accordance with pathway analysis to assess impacts and the implications of ALARA specified in 40 CFR 192 relative to supplemental standards.

  9. DOE final report phase one startup, Waste Receiving and Processing Facility (WRAP)

    International Nuclear Information System (INIS)

    Jasen, W.G.

    1998-01-01

    This document is to validate that the WRAP facility is physically ready to start up phase 1, and that the managers and operators are prepared to safely manage and operate the facility when all pre-start findings have been satisfactorily corrected. The DOE Readiness Assessment (RA) team spent a week on-site at Waste Receiving and Processing Module 1 (WRAP-1) to validate the readiness for phase 1 start up of facility. The Contractor and DOE staff were exceptionally cooperative and contributed significantly to the overall success of the RA. The procedures and Conduct of Operations areas had significant discrepancies, many of which should have been found by the contractor review team. In addition the findings of the contractor review team should have led the WRAP-1 management team to correcting the root causes of the findings prior to the DOE RA team review. The findings and observations include many issues that the team believes should have been found by the contractor review and corrective actions taken. A significantly improved Operational Readiness Review (ORR) process and corrective actions of root causes must be fully implemented by the contractor prior to the performance of the contractor ORR for phase 2 operations. The pre-start findings as a result of this independent DOE Readiness Assessment are presented

  10. Shutdown and degradation: Optimization of thermal cutting processes for the dismantling of nuclear facilities. Final report

    International Nuclear Information System (INIS)

    Schultz, H.; Hammer, G.; Hampe, A.; Homburg, A.

    1996-01-01

    Cutting processes are required for the dismantling of nuclear facilities which emit only a minimum of contaminated material in the form of shavings, sparks, dust, steam concentrate etc. and equipment which is easy to handle and can be remote controlled. A check of the usual mechanical, thermal and thermo-mechanical cutting procedures showed to what varying extent they are suitable for these tasks. Also the laser beam cutting was able to reduce the material discharge by optimal joints. For the investigation, the plasma cutting and the laser beam cutting were used with the aim of reducing considerably the material discharge by changing the adjust and device setting data for theses cases. The adapting of the speed and the amounts of gas turned out to be effective measures in reducing discharge. Adhesion of metal mass and slag in the joint edge could be achieved with aggressive bearth formation. The expectations made of the project could be fulfilled and process parameters for a pollutant optimised cutting determined. (orig.) [de

  11. Defense Waste Processing Facility: Savannah River Plant, Aiken, SC. Final environmental impact statement

    International Nuclear Information System (INIS)

    1982-02-01

    The purpose of this Environmental Impact Statement (EIS) is to provide environmental input into both the selection of an appropriate strategy for the permanent disposal of the high-level radioactive waste (HLW) currently stored at the Savannah River Plant (SRP) and the subsequent decision to construct and operate a Defense Waste Processing Facility (DWPF) at the SRP site. The SRP is a major US Department of Envgy (DOE) installation for the production of nuclear materials for national defense. Approximately 83 x 10 3 m 3 (22 million gal) of HLW currently are stored in tanks at the SRP site. The proposed DWPF would process the liquid HLW generated by SRP operations into a stable form for ultimate disposal. This EIS assesses the effects of the proposed immobilization project on land use, air quality, water quality, ecological systems, health risk, cultural resources, endangered species, wetlands protection, resource depletion, and regional social and economic systems. The radiological and nonradiological risks of transporting the immobilized wastes are assessed. The environmental impacts of disposal alternatives have recently been evaluated in a previous EIS and are therefore only summarized in this EIS

  12. Advanced-safeguards systems development for chemical-processing plants. Final report for FY 1980

    International Nuclear Information System (INIS)

    Cartan, F.O.

    1981-04-01

    The program is installing a computer system to test and evaluate process monitoring as a new Safeguards function to supplement the usual physical security and accountability functions. Safeguards development sensors and instruments installed in the Idaho Chemical Processing Plant (ICPP) provide information via a data acquisition system to a Safeguards analysis computer. The monitoring function can significantly enhance current material control (accountability) and containment surveillance capabilities for domestic and international Safeguards uses. Installation of sensors and instruments in the ICPP was more than 75% complete in FY-1980. Installation work was halted at the request of ICPP operations near the end of the year to eliminate possible conflict with instrument calibrations prior to plant startup. Some improvements to the computer hardware were made during FY-1980. Sensor and instrument development during FY-1980 emphasized device testing for ICPP monitoring applications. Pressure transducers, pressure switches, a bubble flowmeter, and load cells were tested; an ultrasonic liquid-in-line sensor was developed and tested. Work on the portable, isotope-ratio mass spectrometer led to the comparison of the HP quadrupole instrument with a small magnetic instrument and to the selection of the quadrupole

  13. Cesium removal demonstration utilizing crystalline silicotitanate sorbent for processing Melton Valley Storage Tank supernate: Final report

    International Nuclear Information System (INIS)

    Walker, J.F. Jr.; Taylor, P.A.; Cummins, R.L.

    1998-03-01

    This report provides details of the Cesium Removal Demonstration (CsRD), which was conducted at Oak Ridge National Laboratory (ORNL) on radioactive waste from the Melton Valley Storage Tanks. The CsRD was the first large-scale use of state-of-the-art sorbents being developed by private industry for the selective removal of cesium and other radionuclides from liquid wastes stored across the DOE complex. The crystalline silicotitanate sorbent used in the demonstration was chosen because of its effectiveness in laboratory tests using bench-scale columns. The demonstration showed that the cesium could be removed from the supernate and concentrated on a small-volume, solid waste form that would meet the waste acceptance criteria for the Nevada Test Site. During this project, the CsRD system processed > 115,000 L (30,000 gal) of radioactive supernate with minimal operational problems. Sluicing, drying, and remote transportation of the sorbent, which could not be done on a bench scale, were successfully demonstrated. The system was then decontaminated to the extent that it could be contact maintained with the use of localized shielding only. By utilizing a modular, transportable design and placement within existing facilities, the system can be transferred to different sites for reuse. The initial unit has now been removed from the process building and is presently being reinstalled for use in baseline operations at ORNL

  14. Electrochemical Processes for In-Situ Treatment of Contaminated Soils - Final Report - 09/15/1996 - 01/31/2001

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Chin-Pao

    2001-05-31

    This project will study electrochemical processes for the in situ treatment of soils contaminated by mixed wastes, i.e., organic and inorganic. Soil samples collected form selected DOE waste sites will be characterized for specific organic and metal contaminants and hydraulic permeability. The soil samples are then subject to desorption experiments under various physical-chemical conditions such as pH and the presence of surfactants. Batch electro-osmosis experiments will be conducted to study the transport of contaminants in the soil-water systems. Organic contaminants that are released from the soil substrate will be treated by an advanced oxidation process, i.e., electron-Fantan. Finally, laboratory reactor integrating the elector-osmosis and elector-Fantan processes will be used to study the treatment of contaminated soil in situ.

  15. Rejection of unfair offers can be driven by negative emotions, evidence from modified ultimatum games with anonymity.

    Science.gov (United States)

    Ma, Ning; Li, Nan; He, Xiao-Song; Sun, De-Lin; Zhang, Xiaochu; Zhang, Da-Ren

    2012-01-01

    The rejection of unfair offers can be affected by both negative emotions (e.g. anger and moral disgust) and deliberate cognitive processing of behavioral consequences (e.g. concerns of maintaining social fairness and protecting personal reputation). However, whether negative emotions are sufficient to motivate this behavior is still controversial. With modified ultimatum games, a recent study (Yamagishi T, et al. (2009) Proc Natl Acad Sci USA 106:11520-11523) found that people reject unfair offers even when this behavior increases inequity, and even when they could not communicate to the proposers. Yamagishi suggested that rejection of unfair offers could occur without people's concerning of maintaining social fairness, and could be driven by negative emotions. However, as anonymity was not sufficiently guaranteed in Yamagishi's study, the rejection rates in their experiments may have been influenced by people's concerns of protecting personal reputation (reputational concerns) in addition to negative emotions; thus, it was unclear whether the rejection was driven by negative emotions, or by reputational concerns, or both. In the present study, with specific methods to ensure anonymity, the effect of reputational concerns was successfully ruled out. We found that in a private situation in which rejection could not be driven by reputational concerns, the rejection rates of unfair offers were significantly larger than zero, and in public situations in which rejection rates could be influenced by both negative emotions and reputational concerns, rejection rates were significantly higher than that in the private situation. These results, together with Yamagishi's findings, provided more complete evidence suggesting (a) that the rejection of unfair offers can be driven by negative emotions and (b) that deliberate cognitive processing of the consequences of the behavior can increase the rejection rate, which may benefit social cooperation.

  16. Assessing middle school students` understanding of science relationships and processes. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Schau, C.; Mattern, N.; Weber, R. [Univ. of New Nexico, Albuquerque, NM (United States); Minnick, K. [Minnick & Associates, Inc., Albuquerque, NM (United States)

    1994-09-01

    Our overall goal for this multi-year project is to develop and validate an alternative assessment format that effectively measures middle school students understanding of the relationships among selected science concepts and processes. In this project, we collaborate with the staff of the Los Alamos National Laboratory`s TOPS Program and the Programs participating teachers and their students. We also work with selected middle school science teachers from the TOPS program at Sandia National Laboratories. Our goal for this past year was to develop and field test informally a variety of potential measurement formats. This work has allowed us to identify formats to test during the validation phase of the project which will occur during the second year.

  17. Radiological surveillance of Remedial Action activities at the processing site, Falls City, Texas. Final report

    International Nuclear Information System (INIS)

    1993-04-01

    The Uranium Mill Tailings Remedial Action (UMTRA) Project's Technical Assistance Contractor (TAC) performed a radiological surveillance of the Remedial Action Contractor (RAC), MK-Ferguson and CWM Federal Environmental Services, Inc., at the processing site in Falls City, Texas. This surveillance was conducted March 22--26, 1993. No findings were identified during the surveillance. Three site-specific observations and three programmatic observations are presented in this report. The overall conclusion from the surveillance is that the radiological aspects of the Falls City, Texas, remedial action program are performed adequately. However, some of the observations identify that there is potential for improving certain aspects of the occupational radiological air sampling, ensuring analytical data quality, and in communicating with the DOE and TAC on the ore sampling methods. The TAC has also received and is currently reviewing the RAC's responses regarding the observations identified during the radiological surveillance performed October 29--30, 1992

  18. Final characterization report for the non-process areas of the 233-S Plutonium Concentration Facility

    International Nuclear Information System (INIS)

    Encke, D.B.; Harris, R.A.

    1997-04-01

    This report addresses the 233-S Plutonium Concentration Facility characterization survey data collected from January 21, 1997 through February 3, 1997. The characterization activities evaluated the radiological status and identified the hazardous materials locations. The scope of this report is limited to the nonprocess areas in the facility, which include the special work permit (SWP) change room, toilet, equipment room, electrical cubicle, control room, and pipe gallery. A portion of the roof (excluding the roof over the process hood and viewing room) was also included. Information in this report will be used to identify waste streams, provide specific chemical and radiological data to aid in planning decontamination and demolition activities, and allow proper disposal of the demolition debris, as required by the Comprehensive Environmental Response, Compensation, and Liability Act of 1980

  19. REJECTION TO LEARNING OF MATHEMATICS BECAUSE OF VIOLENCE IN THE TECHNOLOGICAL BACCALAUREATE

    Directory of Open Access Journals (Sweden)

    Francisco Caballero-Jiménez

    2016-01-01

    Full Text Available This paper corresponds the first theoretical and applied results in the thesis of the author and director, and aims to make a conceptual review of school education and its importance in society and the study of mathematics and as these are rejected and stigmatized. In turn, we study, how it manifests itself direct, structural and cultural violence in learning math to finally propose peace education as alternative in order to influence the rejection and stigma regarding mathematics, trying to improve their learning.

  20. Effects of composite mango ( Mangifera indica ) fruit reject meal on ...

    African Journals Online (AJOL)

    Effects of composite mango ( Mangifera indica ) fruit reject meal on growth performance, digestibility and economics of production of rabbits. ... The experiment was conducted to determine the effect of mango fruit reject ... HOW TO USE AJOL.

  1. THE DIAGNOSIS OF LIVER ALLOGRAFT ACUTE REJECTION IN LIVER BIOPSIES

    Directory of Open Access Journals (Sweden)

    L. V. Shkalova

    2011-01-01

    Full Text Available We performed histological examination of 80 liver allograft biopsies, the diagnosis of acute rejection was proved in 34 cases. Histological changes in liver biopsies in different grades of acute rejection were estimated according to Banff classification 1995, 1997 and were compared with current literature data. The article deals with the question of morphological value of grading acute rejection on early and late, also we analyze changes in treat- ment tactics after morphological verification of liver allograft acute rejection

  2. Industrial yogurt manufacture: monitoring of fermentation process and improvement of final product quality.

    Science.gov (United States)

    Soukoulis, C; Panagiotidis, P; Koureli, R; Tzia, C

    2007-06-01

    Lactic acid fermentation during the production of skim milk and whole fat set-style yogurt was continuously monitored by measuring pH. The modified Gompertz model was successfully applied to describe the pH decline and viscosity development during the fermentation process. The viscosity and incubation time data were also fitted to linear models against ln(pH). The investigation of the yogurt quality improvement practices included 2 different heat treatments (80 degrees C for 30 min and 95 degrees C for 10 min), 3 milk protein fortifying agents (skim milk powder, whey powder, and milk protein concentrate) added at 2.0%, and 4 hydrocolloids (kappa-carrageenan, xanthan, guar gum, and pectin) added at 0.01% to whole fat and skim yogurts. Heat treatment significantly affected viscosity and acetaldehyde development without influencing incubation time and acidity. The addition of whey powder shortened the incubation time but had a detrimental effect on consistency, firmness, and overall acceptance of yogurts. On the other hand, addition of skim milk powder improved the textural quality and decreased the vulnerability of yogurts to syneresis. Anionic stabilizers (kappa-carrageenan and pectin) had a poor effect on the texture and palatability of yogurts. However, neutral gums (xanthan and guar gum) improved texture and prevented the wheying-off defect. Skim milk yogurts exhibited longer incubation times and higher viscosities, whereas they were rated higher during sensory evaluation than whole fat yogurts.

  3. Collisional processes of interest in MFE plasma research. Final report, October 1, 1975-December 31, 1981

    International Nuclear Information System (INIS)

    Olson, R.E.

    1981-01-01

    Research on this contract over the past five years can be divided into several general topics: (1) D - formation processes for ion source related work, (2) collisions between atomic H or D and multiply-charged impurity ions for the diagnosis of plasma properties, and (3) the study of alpha particle collisions to determine confinement times. For topic (1), we completed theoretical calculations on the differential (angular) scattering of H 0 and D 0 on Cs, and detemined the mechanisms and trends in the electron detachment cross sections for collisions of H - and D - with alkali and heavy alkaline earth atom systems. For topic (2), a cross section scaling rule was determined for electron removal from atomic hydrogen by multiply charged ion collisions for charge states q = 1 to 50 and for collision energies from 50 to 5000 keV/amu. On topic (3), we completed He ++ + Li double electron capture and single ionization cross section calculations from 50 to 400 keV/amu for use in studies on alpha distributions in magnetically confined plasmas. The cross section values are such that this diagnostic procedure appears tractable

  4. ParaText : scalable solutions for processing and searching very large document collections : final LDRD report.

    Energy Technology Data Exchange (ETDEWEB)

    Crossno, Patricia Joyce; Dunlavy, Daniel M.; Stanton, Eric T.; Shead, Timothy M.

    2010-09-01

    This report is a summary of the accomplishments of the 'Scalable Solutions for Processing and Searching Very Large Document Collections' LDRD, which ran from FY08 through FY10. Our goal was to investigate scalable text analysis; specifically, methods for information retrieval and visualization that could scale to extremely large document collections. Towards that end, we designed, implemented, and demonstrated a scalable framework for text analysis - ParaText - as a major project deliverable. Further, we demonstrated the benefits of using visual analysis in text analysis algorithm development, improved performance of heterogeneous ensemble models in data classification problems, and the advantages of information theoretic methods in user analysis and interpretation in cross language information retrieval. The project involved 5 members of the technical staff and 3 summer interns (including one who worked two summers). It resulted in a total of 14 publications, 3 new software libraries (2 open source and 1 internal to Sandia), several new end-user software applications, and over 20 presentations. Several follow-on projects have already begun or will start in FY11, with additional projects currently in proposal.

  5. Thin film CIGS solar cells with a novel low cost process - Final report

    Energy Technology Data Exchange (ETDEWEB)

    Tiwari, A. N.; Romanyuk, Y.

    2010-01-15

    Novel manufacturing routes for efficient and low-cost Cu(In,Ga)Se{sub 2} (called CIGS) thin film solar cells are explored and patented. CIGS has proven its suitability for highly efficient and extremely stable solar cells. The low-cost methods allow impurity free material synthesis, fast large-area deposition, high material utilization and a very short energy payback time with drastically lower manufacturing costs. Two non-vacuum, solution-based approaches are investigated to deposit thin layers of CIGS. The first approach considers incorporation of copper into indium gallium selenide precursor layers by ion-exchange from aqueous or organic solutions. Organic solutions provide faster copper incorporation and do not corrode the metal back contact. Solar cells processed from selenized precursor films exhibit efficiencies of up to 4.1%. The second approach with paste coating of inorganic salt solution results in a solar cell efficiency of 4% (record 6.7%), where further improvements are hindered by the presence of the residual carbon layer. Using alternative organic binders, pre-deposited selenium layers, non-binder recipes helps to avoid the carbon layer although the obtained layers are inhomogeneous and contain impurity phases. A patent for the ion-exchange approach is pending, and the obtained research results on the paste coating approach will be scrutinized during new European FP7 project 'NOVA-CIGS'. (authors)

  6. Life Improvement of Pot Hardware in Continuous Hot Dipping Processes Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Xingbo Liu

    2006-01-18

    The process of continuous galvanizing of rolled sheet steel includes immersion into a bath of molten zinc/aluminum alloy. The steel strip is dipped in the molten bath through a series of driving motors and rollers which control the speed and tension of the strip, with the ability to modify both the amount of coating applied to the steel as well as the thickness and width of the sheet being galvanized. There are three rolls used to guide the steel strip through the molten metal bath. The rolls that operate in the molten Zn/Al are subject to a severely corrosive environment and require frequent changing. The performance of this equipment, the metallic hardware submerged in the molten Zn/Al bath, is the focus of this research. The primary objective of this research is to extend the performance life of the metallic hardware components of molten Zn/Al pot hardware by an order of magnitude. Typical galvanizing operations experience downtimes on the order of every two weeks to change the metallic hardware submerged in the molten metal bath. This is an expensive process for industry which takes upwards of 3 days for a complete turn around to resume normal operation. Each roll bridle consists of a sink, stabilizer, and corrector roll with accompanying bearing components. The cost of the bridle rig with all components is as much as $25,000 dollars just for materials. These inefficiencies are of concern to the steel coating companies and serve as a potential market for many materials suppliers. This research effort served as a bridge between the market potential and industry need to provide an objective analytical and mechanistic approach to the problem of wear and corrosion of molten metal bath hardware in a continuous sheet galvanizing line. The approach of the investigators was to provide a means of testing and analysis that was both expeditious and cost effective. The consortium of researchers from West Virginia University and Oak Ridge National Laboratory developed

  7. Theory of high energy collision processes. Final report, June 1, 1969-May 31, 1984

    International Nuclear Information System (INIS)

    Wu, T.T.

    1984-01-01

    We have developed a comprehensive theory for scattering processes at extremely high energies. On the basis of relativistic quantum field theories with or without isotopic spin, we have obtained a simple physical picture, called the impact picture, which gives a number of unusual predictions. Many of these have been verified experimentally, including the increasing total cross sections, the increasing total elastic cross sections, the moving dip, and the rising plateau. An especially accurate experimental verification of the prediction of increasing total cross section has been provided by the CERN p anti p Collider at a c.m. energy of 540 GeV. All of these predictions were obtained by resumming the perturbation series. The natural next step is to look for important physical effects that cannot be seen by any method of resumming the perturbation series. One such method is to find nonperturbative effects already present on the classical level; another is to construct exactly solvable models of quantum field theory. Both approaches have been pursued. Recent theoretical results include the possible occurrence of indeterminate-mass particles, dynamic determination of coupling constants, a solvable Z 2 lattice gauge theory, a generalization of the method of helicity amplitudes, classical models of confinement, and a monopole as a short-distance probe. 152 publications are listed

  8. Final Scientific Report, Integrated Seismic Event Detection and Location by Advanced Array Processing

    Energy Technology Data Exchange (ETDEWEB)

    Kvaerna, T.; Gibbons. S.J.; Ringdal, F; Harris, D.B.

    2007-01-30

    In the field of nuclear explosion monitoring, it has become a priority to detect, locate, and identify seismic events down to increasingly small magnitudes. The consideration of smaller seismic events has implications for a reliable monitoring regime. Firstly, the number of events to be considered increases greatly; an exponential increase in naturally occurring seismicity is compounded by large numbers of seismic signals generated by human activity. Secondly, the signals from smaller events become more difficult to detect above the background noise and estimates of parameters required for locating the events may be subject to greater errors. Thirdly, events are likely to be observed by a far smaller number of seismic stations, and the reliability of event detection and location using a very limited set of observations needs to be quantified. For many key seismic stations, detection lists may be dominated by signals from routine industrial explosions which should be ascribed, automatically and with a high level of confidence, to known sources. This means that expensive analyst time is not spent locating routine events from repeating seismic sources and that events from unknown sources, which could be of concern in an explosion monitoring context, are more easily identified and can be examined with due care. We have obtained extensive lists of confirmed seismic events from mining and other artificial sources which have provided an excellent opportunity to assess the quality of existing fully-automatic event bulletins and to guide the development of new techniques for online seismic processing. Comparing the times and locations of confirmed events from sources in Fennoscandia and NW Russia with the corresponding time and location estimates reported in existing automatic bulletins has revealed substantial mislocation errors which preclude a confident association of detected signals with known industrial sources. The causes of the errors are well understood and are

  9. Final Scientific Report, Integrated Seismic Event Detection and Location by Advanced Array Processing

    International Nuclear Information System (INIS)

    Kvaerna, T.; Gibbons. S.J.; Ringdal, F; Harris, D.B.

    2007-01-01

    In the field of nuclear explosion monitoring, it has become a priority to detect, locate, and identify seismic events down to increasingly small magnitudes. The consideration of smaller seismic events has implications for a reliable monitoring regime. Firstly, the number of events to be considered increases greatly; an exponential increase in naturally occurring seismicity is compounded by large numbers of seismic signals generated by human activity. Secondly, the signals from smaller events become more difficult to detect above the background noise and estimates of parameters required for locating the events may be subject to greater errors. Thirdly, events are likely to be observed by a far smaller number of seismic stations, and the reliability of event detection and location using a very limited set of observations needs to be quantified. For many key seismic stations, detection lists may be dominated by signals from routine industrial explosions which should be ascribed, automatically and with a high level of confidence, to known sources. This means that expensive analyst time is not spent locating routine events from repeating seismic sources and that events from unknown sources, which could be of concern in an explosion monitoring context, are more easily identified and can be examined with due care. We have obtained extensive lists of confirmed seismic events from mining and other artificial sources which have provided an excellent opportunity to assess the quality of existing fully-automatic event bulletins and to guide the development of new techniques for online seismic processing. Comparing the times and locations of confirmed events from sources in Fennoscandia and NW Russia with the corresponding time and location estimates reported in existing automatic bulletins has revealed substantial mislocation errors which preclude a confident association of detected signals with known industrial sources. The causes of the errors are well understood and are

  10. Parallel processing and learning in simple systems. Final report, 10 January 1986-14 January 1989

    Energy Technology Data Exchange (ETDEWEB)

    Mpitsos, G.J.

    1989-03-15

    Work over the three-year tenure of this grant has dealt with interrelated studies of (1) neuropharmacology, (2) behavior, and (3) distributed/parallel processing in the generation of variable motor patterns in the buccal-oral system of the sea slug Pleurobranchaea californica. (4) Computer simulations of simple neutral networks have been undertaken to examine neurointegrative principles that could not be examined in biological preparations. The simulation work has set the basis for further simulations dealing with networks having characteristics relating to real neurons. All of the work has had the goal of developing interdisciplinary tools for understanding the scale-independent problem of how individuals, each possessing only local knowledge of group activity, act within a group to produce different and variable adaptive outputs, and, in turn, of how the group influences the activity of the individual. The pharmacologic studies have had the goal of developing biochemical tools with which to identify groups of neurons that perform specific tasks during the production of a given behavior but are multifunctional by being critically involved in generating several different behaviors.

  11. Kinetics and Mechanism of Metal Retention/Release in Geochemical Processes in Soil - Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, Robert W.

    2000-12-29

    Effective, remediation of soils contaminated with heavy metals requires a better understanding of the mechanisms by which the metals are retained/released in soils over a long period of time. Studies on reaction of Cr(VI) with iron-rich clays indicated that structural iron (II) in these surfaces is capable of reducing chromate to chromium (III). We found that iron (II) either found naturally or produced by treatment of clay with sodium dithionite, effectively reduced Cr (VI) to Cr (III). Thus, in situ remediation of chromium combines reduction of Cr (VI) to Cr (III) and immobilization of chromium on mineral surfaces. During this study, lead sorption on a kaolin surface was found to be a rapid and a pH dependant process in which lead sorption significantly increased with the amount of phosphate on the clay surface. This study verifies that methylmercury cation remains intact when it binds to humic acids, forming a monodentate complex with some sub-population of humic thiol ligands .

  12. Performance assessment and adoption processes of an information monitoring and diagnostic system prototype; FINAL

    International Nuclear Information System (INIS)

    Piette, Mary Ann

    1999-01-01

    This report addresses the problem that buildings do not perform as well as anticipated during design. We partnered with an innovative building operator to evaluate a prototype Information Monitoring and Diagnostic System (IMDS). The IMDS consists of high-quality measurements archived each minute, a data visualization tool, and a web-based capability. The operators recommend similar technology be adopted in other buildings. The IMDS has been used to identify and correct a series of control problems. It has also allowed the operators to make more effective use of the building control system, freeing up time to take care of other tenant needs. They believe they have significantly improved building comfort, potentially improving tenant health, and productivity. The reduction in hours to operate the building are worth about$20,000 per year, which could pay for the IMDS in about five years. A control system retrofit based on findings from the IMDS is expected to reduce energy use by 20 percent over the next year, worth over$30,000 per year. The main conclusion of the model-based chiller fault detection work is that steady-state models can be used as reference models to monitor chiller operation and detect faults. The ability of the IMDS to measure cooling load and chiller power to one-percent accuracy with a one-minute sampling interval permits detection of additional faults. Evolutionary programming techniques were also evaluated, showing promise in the detection of patterns in building data. We also evaluated two technology adoption processes, radical and routine. In routine adoption, managers enhance features of existing products that are already well understood. In radical adoption, innovative building managers introduce novel technology into their organizations without using the rigorous payback criteria used in routine innovations

  13. Process engineering and economic evaluations of diaphragm and membrane chlorine cell technologies. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1980-12-01

    The chlor-alkali manufacturing technologies of (1), diaphragm cells (2), current technology membrane cells (3), catalytic cathode membrane cells (4), oxygen-cathode membrane cells and to a lesser extent several other related emerging processes are studied. Comparisons have been made on the two bases of (1) conventional industrial economics, and (2) energy consumption. The current diaphragm cell may have a small economic advantage over the other technologies at the plant size of 544 metric T/D (600 T/D). The three membrane cells all consume less energy, with the oxygen-cathode cell being the lowest. The oxygen-cathode cell appears promising as a low energy chlor-alkali cell where there is no chemical market for hydrogen. Federal funding of the oxygen-cathode cell has been beneficial to the development of the technology, to electrochemical cell research, and may help maintain the US's position in the international chlor-alkali technology marketplace. Tax law changes inducing the installation of additional cells in existing plants would produce the quickest reduction in power consumption by the chlor-alkali industry. Alternative technologies such as the solid polymer electrolyte cell, the coupling of diaphragm cells with fuel cells and the dynamic gel diaphragm have a strong potential for reducing chloralkali industry power consumption. Adding up all the recent and expected improvements that have become cost-effective, the electrical energy required to produce a unit of chlorine by 1990 should be only 50% to 60% of that used in 1970. In the United States the majority of the market does not demand salt-free caustic. About 75% of the electrolytic caustic is produced in diaphragm cells and only a small part of that is purified. This study indicates that unless membrane cell costs are greatly reduced or a stronger demand develops for salt-free caustic, the diaphragm cells will remain competitive. (WHK)

  14. Syngas to Synfuels Process Development Unit Final Scientific/Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Robert C. [Iowa State Univ., Ames, IA (United States)

    2012-03-30

    The process described is for the gasification of 20 kg/h of biomass (switchgrass) to produce a syngas suitable for upgrading to Fischer-Tropsch (FT) liquid fuels (gas, diesel, waxes, etc.). The gas stream generated from gasification is primarily composed of carbon monoxide (CO), hydrogen (H2), carbon dioxide (CO2), steam (H2O), and methane (CH4), but also includes tars, particulate matter, ammonia (NH3), hydrogen cyanide (HCN), hydrogen chloride (HCl), hydrogen sulfide ( H2S), carbonyl sulfide (COS), etc. as contaminants. The gas stream passes through an array of cleaning devices to remove the contaminants to levels suitable for FT synthesis of fuels/chemicals. These devices consist primarily of an oil scrubber (to remove tars and remaining particulates), sulfur scrubber (to remove sulfur compounds), and a wet scrubber (to remove NH3, HCl and remaining water soluble contaminants). The ammonia and oil scrubbers are absorption columns with a combination of random and structured packing materials, using water and oil as the adsorption liquids respectively. The ammonia scrubber performed very well, while operating the oil scrubber proved to be more difficult due to the nature of tar compounds. The sulfur scrubber is a packed bed absorption device with solid extrudates of adsorbent material, primarily composed of ZnO and CuO. It performed well, but over a limited amount of time due to fouling created by excess tar/particulate matter and oil aerosols. Overall gas contaminants were reduced to below 1 ppm NH3, and less than 1 ppm collective sulfur compounds.

  15. HANFORD CONTAINERIZED CAST STONE FACILITY TASK 1 PROCESS TESTING & DEVELOPMENT FINAL TEST REPORT

    Energy Technology Data Exchange (ETDEWEB)

    LOCKREM, L L

    2005-07-13

    Laboratory testing and technical evaluation activities on Containerized Cast Stone (CCS) were conducted under the Scope of Work (SOW) contained in CH2M HILL Hanford Group, Inc. (CHG) Contract No. 18548 (CHG 2003a). This report presents the results of testing and demonstration activities discussed in SOW Section 3.1, Task I--''Process Development Testing'', and described in greater detail in the ''Containerized Grout--Phase I Testing and Demonstration Plan'' (CHG, 2003b). CHG (2003b) divided the CCS testing and evaluation activities into six categories, as follows: (1) A short set of tests with simulant to select a preferred dry reagent formulation (DRF), determine allowable liquid addition levels, and confirm the Part 2 test matrix. (2) Waste form performance testing on cast stone made from the preferred DRF and a backup DRF, as selected in Part I, and using low activity waste (LAW) simulant. (3) Waste form performance testing on cast stone made from the preferred DRF using radioactive LAW. (4) Waste form validation testing on a selected nominal cast stone formulation using the preferred DRF and LAW simulant. (5) Engineering evaluations of explosive/toxic gas evolution, including hydrogen, from the cast stone product. (6) Technetium ''getter'' testing with cast stone made with LAW simulant and with radioactive LAW. In addition, nitrate leaching observations were drawn from nitrate leachability data obtained in the course of the Parts 2 and 3 waste form performance testing. The nitrate leachability index results are presented along with other data from the applicable activity categories.

  16. High density turbulent plasma processes from a shock tube. Final performance report

    International Nuclear Information System (INIS)

    Johnson, J.A. III.

    1997-01-01

    A broad-based set of measurements has begun on high density turbulent plasma processes. This includes determinations of new plasma physics and the initiation of work on new diagnostics for collisional plasmas as follows: (1) A transient increase is observed in both the spectral energy decay rate and the degree of chaotic complexity at the interface of a shock wave and a turbulent ionized gas. Even though the gas is apparently brought to rest by the shock wave, no evidence is found either of prompt relaminarization or of any systematic influence of end-wall material thermal conductivities on the turbulence parameters. (2) Point fluorescence emissions and averaged spectral line evolutions in turbulent plasmas produced in both the primary and the reflected shock wave flows exhibit ergodicity in the standard turbulence parameters. The data show first evidence of a reverse energy cascade in the collisional turbulent plasma. This suggests that the fully turbulent environment can be described using a stationary state formulation. In these same data, the author finds compelling evidence for a turbulent Stark effect on neutral emission lines in these data which is associated with evidence of large coherent structures and dominant modes in the Fourier analyses of the fluctuations in the optical spectra. (3) A neutral beam generator has been assembled by coupling a Colutron Ion Gun to a charge exchange chamber. Beam-target collisions where the target species is neutral and the beam is either singly charged or neutral have been performed using argon as the working gas. Spectral analysis of the emission shows specific radiative transitions characteristic of both Ar I and Ar II, indicating that some ionization of the target gas results. Gas and plasma parameters such as density, pressure, temperature and flow velocity and their fluctuations can now be followed in real time by spectroscopic analysis of carefully chosen radiative emissions

  17. Rejection Sensitivity, Perceived Power, and HIV Risk in the Relationships of Low-Income Urban Women.

    Science.gov (United States)

    Berenson, Kathy R; Paprocki, Christine; Thomas Fishman, Marget; Bhushan, Devika; El-Bassel, Nabila; Downey, Geraldine

    2015-01-01

    The psychological processes associated with HIV infection in long-term relationships differ from those operative in casual sexual encounters, and relatively little research has considered the aspects of personality applicable in the ongoing heterosexual relationships in which women are at greatest risk. Sensitivity to rejection has been linked with efforts to prevent rejection at a cost to the self and, therefore, may be relevant to the health risks that many women incur in relationships. We examined the association of rejection sensitivity with women's sexual risk behavior in a sample of women at heightened risk for HIV exposure. Women in long-term heterosexual relationships (N = 159) were recruited for study participation in the hospital emergency room serving a low-income neighborhood in New York City, in 2001-2003. Rejection sensitivity and known HIV risk factors were assessed using verbally administered questionnaires. Rejection sensitivity was associated with lower perceived relationship power and, in turn, more frequent unprotected sex with a partner perceived to be at risk for HIV. These results held when controlling for other HIV risk factors including partner violence, economic dependence, and substance use. Understanding the association of rejection concerns with lower perceived personal power in relationships may be important for HIV prevention.

  18. Resilience and rejection sensitivity mediate long-term outcomes of parental divorce.

    Science.gov (United States)

    Schaan, Violetta K; Vögele, Claus

    2016-11-01

    Increasing divorce rates leave more and more children to deal with the separation of their parents. Recent research suggests that children of divorced parents more often experience psychological and physical symptoms than children of non-divorced parents. The processes that mediate the relationship between parental divorce and ill-health, however, are still elusive. This study investigated the mediating role of psychological factors such as resilience and rejection sensitivity on the long-term consequences of parental divorce in young adults. One hundred and ninety-nine participants (mean age 22.3 years) completed an online survey, including measures of mental health, childhood trauma, resilience, and rejection sensitivity. Participants with divorced parents (33 %) reported increased levels of psychological symptoms, childhood trauma, rejection sensitivity, and lower levels of resilience. The association between parental divorce and mental health was fully mediated by resilience, rejection sensitivity, and childhood trauma. The mediation model explained up to 44 % of the total variance in mental health symptoms. Resilience and rejection sensitivity are crucial factors for successful coping with the experience of parental separation. Prevention programs that help to boost children's resilience might help to reduce the long-term effects of parental divorce on their attachment style (e.g., rejection sensitivity), thereby improving their mental health on the long run. Furthermore, the results call for parental awareness and counseling to target and reduce the observed increased level of childhood trauma. Limitations concern the cross-sectional and retrospective design of the study.

  19. Graft rejection after hematopoietic cell transplantation with nonmyeloablative conditioning

    DEFF Research Database (Denmark)

    Masmas, T.N.; Petersen, S.L.; Madsen, H.O.

    2008-01-01

    over time. The storage temperature of the apheresis products was identified as a risk factor for rejection. Storage of the apheresis products at 5 degrees C diminished the risk of rejection. Low donor T cell chimerism at Day +14 significantly increased the risk of rejection. Seven patients were...

  20. Predicting outcome of acute kidney transplant rejection using

    NARCIS (Netherlands)

    Rekers, Niels Vincent

    2014-01-01

    Acute kidney transplant rejection is an important risk factors for adverse graft outcome. Once diagnosed, it remains difficult to predict the risk of graft loss and the response to anti-rejection treatment. The aim of this thesis was to identify biomarkers during acute rejection, which predict the

  1. Memory Distortion and Its Avoidance: An Event-Related Potentials Study on False Recognition and Correct Rejection.

    Science.gov (United States)

    Cadavid, Sara; Beato, Maria Soledad

    2016-01-01

    Memory researchers have long been captivated by the nature of memory distortions and have made efforts to identify the neural correlates of true and false memories. However, the underlying mechanisms of avoiding false memories by correctly rejecting related lures remains underexplored. In this study, we employed a variant of the Deese/Roediger-McDermott paradigm to explore neural signatures of committing and avoiding false memories. ERP were obtained for True recognition, False recognition, Correct rejection of new items, and, more importantly, Correct rejection of related lures. With these ERP data, early-frontal, left-parietal, and late right-frontal old/new effects (associated with familiarity, recollection, and monitoring processes, respectively) were analysed. Results indicated that there were similar patterns for True and False recognition in all three old/new effects analysed in our study. Also, False recognition and Correct rejection of related lures activities seemed to share common underlying familiarity-based processes. The ERP similarities between False recognition and Correct rejection of related lures disappeared when recollection processes were examined because only False recognition presented a parietal old/new effect. This finding supported the view that actual false recollections underlie false memories, providing evidence consistent with previous behavioural research and with most ERP and neuroimaging studies. Later, with the onset of monitoring processes, False recognition and Correct rejection of related lures waveforms presented, again, clearly dissociated patterns. Specifically, False recognition and True recognition showed more positive going patterns than Correct rejection of related lures signal and Correct rejection of new items signature. Since False recognition and Correct rejection of related lures triggered familiarity-recognition processes, our results suggest that deciding which items are studied is based more on recollection

  2. Memory Distortion and Its Avoidance: An Event-Related Potentials Study on False Recognition and Correct Rejection.

    Directory of Open Access Journals (Sweden)

    Sara Cadavid

    Full Text Available Memory researchers have long been captivated by the nature of memory distortions and have made efforts to identify the neural correlates of true and false memories. However, the underlying mechanisms of avoiding false memories by correctly rejecting related lures remains underexplored. In this study, we employed a variant of the Deese/Roediger-McDermott paradigm to explore neural signatures of committing and avoiding false memories. ERP were obtained for True recognition, False recognition, Correct rejection of new items, and, more importantly, Correct rejection of related lures. With these ERP data, early-frontal, left-parietal, and late right-frontal old/new effects (associated with familiarity, recollection, and monitoring processes, respectively were analysed. Results indicated that there were similar patterns for True and False recognition in all three old/new effects analysed in our study. Also, False recognition and Correct rejection of related lures activities seemed to share common underlying familiarity-based processes. The ERP similarities between False recognition and Correct rejection of related lures disappeared when recollection processes were examined because only False recognition presented a parietal old/new effect. This finding supported the view that actual false recollections underlie false memories, providing evidence consistent with previous behavioural research and with most ERP and neuroimaging studies. Later, with the onset of monitoring processes, False recognition and Correct rejection of related lures waveforms presented, again, clearly dissociated patterns. Specifically, False recognition and True recognition showed more positive going patterns than Correct rejection of related lures signal and Correct rejection of new items signature. Since False recognition and Correct rejection of related lures triggered familiarity-recognition processes, our results suggest that deciding which items are studied is based more on

  3. Final Progress Report: Coupled Biogeochemical Process Evaluation for Conceptualizing Trichloroethylene Cometabolism

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, Ronald L; Paszczynski, Andrzej J

    2010-02-19

    Our goal within the overall project is to demonstrate the presence and abundance of methane monooxygenases (MMOs) enzymes and their genes within the microbial community of the Idaho National Laboratory (INL) Test Area North (TAN) site. MMOs are thought to be the primary catalysts of natural attenuation of trichloroethylene (TCE) in contaminated groundwater at this location. The actual presence of the proteins making up MMO complexes would provide direct evidence for its participation in TCE degradation. The quantitative estimation of MMO genes and their translation products (sMMO and pMMO proteins) and the knowledge about kinetics and substrate specificity of MMOs will be used to develop mathematical models of the natural attenuation process in the TAN aquifer. The model will be particularly useful in prediction of TCE degradation rate in TAN and possibly in the other DOE sites. Bacteria known as methanotrophs produce a set of proteins that assemble to form methane monooxygenase complexes (MMOs), enzymes that oxidize methane as their natural substrate, thereby providing a carbon and energy source for the organisms. MMOs are also capable of co-metabolically transforming chlorinated solvents like TCE into nontoxic end products such as carbon dioxide and chloride. There are two known forms of methane monooxygenase, a membrane-bound particulate form (pMMO) and a cytoplasmic soluble form (sMMO). pMMO consists of two components, pMMOH (a hydroxylase comprised of 47-, 27-, and 24-kDa subunits) and pMMOR (a reductase comprised of 63 and 8-kDa subunits). sMMO consists of three components: a hydroxylase (protein A-250 kDa), a dimer of three subunits (α2β2γ2), a regulatory protein (protein B-15.8 kDa), and a reductase (protein C-38.6 kDa). All methanotrophs will produce a methanol dehydrogenase to channel the product of methane oxidation (methanol) into the central metabolite formaldehyde. University of Idaho (UI) efforts focused on proteomic analyses using mass

  4. ‘Healthy’ identities? : Revisiting rejection-identification and rejection-disidentification models among voluntary and forced immigrants

    NARCIS (Netherlands)

    Bobowik, Magdalena; Martinovic, Borja; Basabe, Nekane; Barsties, Lisa S.; Wachter, Gusta

    2017-01-01

    Rejection-identification and rejection-disidentification models propose that low-status groups identify with their in-group and disidentify with a high-status out-group in response to rejection by the latter. Our research tests these two models simultaneously among multiple groups of foreign-born

  5. USA: California rejects mandatory GMO labelling

    OpenAIRE

    Paull, John

    2012-01-01

    Buying organic remains the best strategy for US consumers to avoid eating GM food. The voters of California have rejected the proposal to label GMO food. The proposition was narrowly lost, 47% to 53% (4,326,770 ‘Yes’ votes vs. 4,884,961 ‘No’ votes). Proposition 47 was supported by the organic sector but opposed by a coalition of GMO companies and US multinational food companies. Californians were invited to vote into law ‘The California Right to Know Genetically Engineered Food Act’. Section ...

  6. Rejection of Bromide and Bromate Ions by a Ceramic Membrane.

    Science.gov (United States)

    Moslemi, Mohammadreza; Davies, Simon H; Masten, Susan J

    2012-12-01

    Effects of pH and the addition of calcium chloride (CaCl(2)) on bromate (BrO(3) (-)) and bromide (Br(-)) rejection by a ceramic membrane were investigated. Rejection of both ions increased with pH. At pH 8, the rejection of BrO(3) (-) and Br(-) was 68% and 63%, respectively. Donnan exclusion appears to play an important role in determining rejection of BrO(3) (-) and Br(-). In the presence of CaCl(2), rejection of BrO(3) (-) and Br(-) ions was greatly reduced, confirming the importance of electrostatic interactions in determining rejection of BrO(3) (-) and Br(-). The effect of Ca(2+) is so pronounced that in most natural waters, rejection of both BrO(3) (-) and Br(-) by the membrane would be extremely small.

  7. Understanding maladaptive responses to rejection: Aggression with an audience.

    Science.gov (United States)

    DeBono, Amber; Layton, Rebekah L; Freeman, Nicholas; Muraven, Mark

    2017-01-01

    Logically, responding aggressively to rejection is maladaptive because one is unlikely to seek a relationship with an aggressor. We predict that when concealed, the illogical aggressive response to rejection is more likely, whereas when the rejected individuals' aggressive responses are perceived as public, the aggressive acts may be reduced. Participants were rejected by others (Experiment 1) or were either accepted or rejected during an online ball-tossing game (Experiment 2) and were then given an opportunity to aggress publicly or privately. Across experiments, when the opportunity to aggress was made public, rejected participants exhibited less aggressive behavior. When concerned about the perception of their public aggressive responses by others, rejected individuals' aggressive responses diminished compared with those whose actions were private. Crucially, this extended to aggression visible only to neutral others, suggesting that effects cannot solely be due to fear of retribution.

  8. Processing development for ceramic structural components: the influence of a presintering of silicon on the final properties of reaction bonded silicon nitride. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    1982-03-01

    The influence of a presintering of silicon on the final properties of reaction bonded silicon nitride has been studied using scanning electron and optical microscopy, x-ray diffraction analysis, 4 pt. bend test, and mecury intrusion porosimetry. It has been shown that presintering at 1050/sup 0/C will not affect the final nitrided properties. At 1200/sup 0/C, the oxide layer is removed, promoting the formation of B-phase silicon nitride. Presintering at 1200/sup 0/C also results in compact weight loss due to the volatilization of silicon, and the formation of large pores which severely reduce nitrided strength. The development of the structure of sintered silicon compacts appears to involve a temperature gradient, with greater sintering observed near the surface.

  9. fMRI Artefact Rejection and Sleep Scoring Toolbox

    Directory of Open Access Journals (Sweden)

    Yves Leclercq

    2011-01-01

    Full Text Available We started writing the “fMRI artefact rejection and sleep scoring toolbox”, or “FAST”, to process our sleep EEG-fMRI data, that is, the simultaneous recording of electroencephalographic and functional magnetic resonance imaging data acquired while a subject is asleep. FAST tackles three crucial issues typical of this kind of data: (1 data manipulation (viewing, comparing, chunking, etc. of long continuous M/EEG recordings, (2 rejection of the fMRI-induced artefact in the EEG signal, and (3 manual sleep-scoring of the M/EEG recording. Currently, the toolbox can efficiently deal with these issues via a GUI, SPM8 batching system or hand-written script. The tools developed are, of course, also useful for other EEG applications, for example, involving simultaneous EEG-fMRI acquisition, continuous EEG eye-balling, and manipulation. Even though the toolbox was originally devised for EEG data, it will also gracefully handle MEG data without any problem. “FAST” is developed in Matlab as an add-on toolbox for SPM8 and, therefore, internally uses its SPM8-meeg data format. “FAST” is available for free, under the GNU-GPL.

  10. Automated Solar Cell Assembly Teamed Process Research. Final subcontract report, 6 January 1993--31 October 1995

    Energy Technology Data Exchange (ETDEWEB)

    Nowlan, M. J.; Hogan, S. J.; Breen, W. F.; Murach, J. M.; Sutherland, S. F.; Patterson, J. S.; Darkazalli, G. [Spire Corp., Bedford, MA (US)

    1996-02-01

    This is the Final Technical Report for a program entitled ''Automated Solar Cell Assembly Teamed Process Research,'' funded by the US Department of Energy. This program was part of Phase 3A of the Photovoltaic Manufacturing Technology (PVMaT) project, which addressed the generic needs of the photovoltaic (PV) industry for improved quality, accelerated production scale-up, and substantially reduced manufacturing cost. Crystalline silicon solar cells (Czochralski monocrystalline, cast polycrystalline, and ribbon polycrystalline) are used in the great majority of PV modules produced in the US, accounting for 95% of all shipments in 1994. Spire's goal in this program was to reduce the cost of these modules by developing high throughput (5 MW per year) automated processes for interconnecting solar cells made from standard and thin silicon wafers. Spire achieved this goal by developing a completely new automated processing system, designated the SPI-ASSEMBLER{trademark} 5000, which is now offered as a commercial product to the PV industry. A discussion of the project and of the Assembler is provided.

  11. ALINET: a model for assessing energy conservation opportunities in the food processing industry. Final technical report, September 1977-December 1979

    Energy Technology Data Exchange (ETDEWEB)

    Levis, A H; Ducot, E R; Levis, I S; Webster, T F

    1979-12-01

    ALINET is a network model designed for the analysis of energy use in the food processing and distribution sector and for the evaluation of the potential effectiveness of energy conserving technologies. The conceptual framework of the model, as well as the design and implementation of the computer software are described. The wheat system at the national, state, and facility-specific level is used to illustrate the model's operation and use. A pilot project, carried out in cooperation with industry, is described in which energy use in (a) hard wheat milling, and (b) durum milling and pasta manufacture is analyzed. Finally, the introduction of an alternative technology for pasta drying is assessed in terms of energy conservation and cost. Recommendation for further applications and institutionalization of the model are made.

  12. Approaches to learning for the ANZCA Final Examination and validation of the revised Study Process Questionnaire in specialist medical training.

    Science.gov (United States)

    Weller, J M; Henning, M; Civil, N; Lavery, L; Boyd, M J; Jolly, B

    2013-09-01

    When evaluating assessments, the impact on learning is often overlooked. Approaches to learning can be deep, surface and strategic. To provide insights into exam quality, we investigated the learning approaches taken by trainees preparing for the Australian and New Zealand College of Anaesthetists (ANZCA) Final Exam. The revised two-factor Study Process Questionnaire (R-SPQ-2F) was modified and validated for this context and was administered to ANZCA advanced trainees. Additional questions were asked about perceived value for anaesthetic practice, study time and approaches to learning for each exam component. Overall, 236 of 690 trainees responded (34%). Responses indicated both deep and surface approaches to learning with a clear preponderance of deep approaches. The anaesthetic viva was valued most highly and the multiple choice question component the least. Despite this, respondents spent the most time studying for the multiple choice questions. The traditionally low short answer questions pass rate could not be explained by limited study time, perceived lack of value or study approaches. Written responses suggested that preparation for multiple choice questions was characterised by a surface approach, with rote memorisation of past questions. Minimal reference was made to the ANZCA syllabus as a guide for learning. These findings indicate that, although trainees found the exam generally relevant to practice and adopted predominantly deep learning approaches, there was considerable variation between the four components. These results provide data with which to review the existing ANZCA Final Exam and comparative data for future studies of the revisions to the ANZCA curriculum and exam process.

  13. Analysis of causes for reject x-ray films as a quality assurance elements in diagnostic radiology in Jos university teaching hospital

    International Nuclear Information System (INIS)

    Anikoh, S.O.; Mangset, W.E.; Habila, N.; Mallam, S.P.

    2010-01-01

    The film reject rate and quality assessments studies were carried out at the Jos University Teaching Hospital. The rejected films collected and counted with respect to type, size and reasons for rejection were carried out for two calendar years. The observed reject rates were found to be nearly independent of the type of X-ray examination, which 68% of waste film reflected the nature and skills employed. The mechanical influence of equipment (machine fault is 11%, film rejection due to poor processing (dark room fault) was found to be 8% and for film rejection due to wrong identification, fogged film, uncooperating patient (patient movement) are 5%, 5% and 3% respectively. The deterioration in the quality of films and film processing conditions, ineffective quality assurance programs and inadequate regular staff training form a possible explanation for observed waste films which could have been avoided.

  14. FINAL INTERIM REPORT VERIFICATION SURVEY ACTIVITIES IN FINAL STATUS SURVEY UNITS 7, 8, 9, 10, 11, 13 and 14 AT THE SEPARATIONS PROCESS RESEARCH UNIT, NISKAYUNA, NEW YORK

    International Nuclear Information System (INIS)

    Jadick, M.G.

    2010-01-01

    The Separations Process Research Unit (SPRU) facilities were constructed in the late 1940s to research the chemical separation of plutonium and uranium. SPRU operated between February 1950 and October 1953. The research activities ceased following the successful development of the reduction/oxidation and plutonium/uranium extraction processes that were subsequently used by the Hanford and the Savannah River sites.

  15. Further development of public participation in the site-selection and approval process of a final repository in Germany

    Energy Technology Data Exchange (ETDEWEB)

    Barth, Regine; Kallenbach-Herbert, Beate [OeEo-Institute e.V., Inst. for Applied Ecology, Darmstadt (Germany); Arens, Georg [Federal Office for Radiation Protection (BfS), Salzgitter (Germany)

    2006-09-15

    This paper reflects the first findings of a current research project funded by the German Federal Office for Radiation Protection and conducted by an interdisciplinary working group of the OEko-Institute. One focus of this project is the systematic analysis of past and existing participatory processes in different nuclear and non-nuclear projects. On the basis of this analysis and a literature review a specific concept for public participation in the site-selection and approval process of a repository for high radioactive waste (HAW repository) in Germany will be derived. The concept shall foster transparency and acceptance. The working group of the OEko-Institute combines long standing research experience and an intimate knowledge of radioactive waste management including political, technical, management and social problems of final disposal on the one hand. On the other hand members play an active role in stakeholder processes of different non-nuclear projects as well as experience with a wide range of participative measures and their impact. This allows an approach which integrates the specific features of radioactive waste disposal with a wider perspective on the demands and opportunities of stakeholder processes. The procedure of site selection for a HAW repository in Germany still has to be specified. The procedure introduced by the 'Committee on a Site Selection Procedure for Repository Sites' (Arbeitskreis Auswahlverfahren Endlagerstandorte - AkEnd) has not been adopted. The Committee had suggested installing a negotiation group to discuss the AkEnd proposals in the so called 'Phase II'. This suggestion could not be followed because not all relevant stakeholders were willing to participate. An internal draft for a federal law implementing main elements of the AkEnd findings was developed by the Ministry for Environment in 2005, but has never been brought to the cabinet. Due to the change of Government in Germany, the next steps still are

  16. Further development of public participation in the site-selection and approval process of a final repository in Germany

    International Nuclear Information System (INIS)

    Barth, Regine; Kallenbach-Herbert, Beate; Arens, Georg

    2006-01-01

    This paper reflects the first findings of a current research project funded by the German Federal Office for Radiation Protection and conducted by an interdisciplinary working group of the OEko-Institute. One focus of this project is the systematic analysis of past and existing participatory processes in different nuclear and non-nuclear projects. On the basis of this analysis and a literature review a specific concept for public participation in the site-selection and approval process of a repository for high radioactive waste (HAW repository) in Germany will be derived. The concept shall foster transparency and acceptance. The working group of the OEko-Institute combines long standing research experience and an intimate knowledge of radioactive waste management including political, technical, management and social problems of final disposal on the one hand. On the other hand members play an active role in stakeholder processes of different non-nuclear projects as well as experience with a wide range of participative measures and their impact. This allows an approach which integrates the specific features of radioactive waste disposal with a wider perspective on the demands and opportunities of stakeholder processes. The procedure of site selection for a HAW repository in Germany still has to be specified. The procedure introduced by the 'Committee on a Site Selection Procedure for Repository Sites' (Arbeitskreis Auswahlverfahren Endlagerstandorte - AkEnd) has not been adopted. The Committee had suggested installing a negotiation group to discuss the AkEnd proposals in the so called 'Phase II'. This suggestion could not be followed because not all relevant stakeholders were willing to participate. An internal draft for a federal law implementing main elements of the AkEnd findings was developed by the Ministry for Environment in 2005, but has never been brought to the cabinet. Due to the change of Government in Germany, the next steps still are under consideration

  17. Final Report - Recovery Act - Development and application of processing and process control for nano-composite materials for lithium ion batteries

    Energy Technology Data Exchange (ETDEWEB)

    Daniel, Claus [ORNL; Armstrong, Beth L [ORNL; Maxey, L Curt [ORNL; Sabau, Adrian S [ORNL; Wang, Hsin [ORNL; Hagans, Patrick [A123 Systems, Inc.; Babinec, Sue [A123 Systems, Inc.

    2013-08-01

    Oak Ridge National Laboratory and A123 Systems, Inc. collaborated on this project to develop a better understanding, quality control procedures, and safety testing for A123 System s nanocomposite separator (NCS) technology which is a cell based patented technology and separator. NCS demonstrated excellent performance. x3450 prismatic cells were shown to survive >8000 cycles (1C/2C rate) at room temperature with greater than 80% capacity retention with only NCS present as an alternative to conventional polyolefin. However, for a successful commercialization, the coating conditions required to provide consistent and reliable product had not been optimized and QC techniques for being able to remove defective material before incorporation into a cell had not been developed. The work outlined in this report addresses these latter two points. First, experiments were conducted to understand temperature profiles during the different drying stages of the NCS coating when applied to both anode and cathode. One of the more interesting discoveries of this study was the observation of the large temperature decrease experienced by the wet coating between the end of the infrared (IR) drying stage and the beginning of the exposure to the convection drying oven. This is not a desirable situation as the temperature gradient could have a deleterious effect on coating quality. Based on this and other experimental data a radiative transfer model was developed for IR heating that also included a mass transfer module for drying. This will prove invaluable for battery coating optimization especially where IR drying is being employed. A stress model was also developed that predicts that under certain drying conditions tensile stresses are formed in the coating which could lead to cracking that is sometimes observed after drying is complete. Prediction of under what conditions these stresses form is vital to improving coating quality. In addition to understanding the drying process other

  18. Proteomic profiling of renal allograft rejection in serum using magnetic bead-based sample fractionation and MALDI-TOF MS.

    Science.gov (United States)

    Sui, Weiguo; Huang, Liling; Dai, Yong; Chen, Jiejing; Yan, Qiang; Huang, He

    2010-12-01

    Proteomics is one of the emerging techniques for biomarker discovery. Biomarkers can be used for early noninvasive diagnosis and prognosis of diseases and treatment efficacy evaluation. In the present study, the well-established research systems of ClinProt Micro solution incorporated unique magnetic bead sample preparation technology, which, based on matrix-assisted laser desorption ionization time-of-flight mass spectrometry (MALDI-TOF MS), have become very successful in bioinformatics due to its outstanding performance and reproducibility for discovery disease-related biomarker. We collected fasting blood samples from patients with biopsy-confirmed acute renal allograft rejection (n = 12), chronic rejection (n = 12), stable graft function (n = 12) and also from healthy volunteers (n = 13) to study serum peptidome patterns. Specimens were purified with magnetic bead-based weak cation exchange chromatography and analyzed with a MALDI-TOF mass spectrometer. The results indicated that 18 differential peptide peaks were selected as potential biomarkers of acute renal allograft rejection, and 6 differential peptide peaks were selected as potential biomarkers of chronic rejection. A Quick Classifier Algorithm was used to set up the classification models for acute and chronic renal allograft rejection. The algorithm models recognize 82.64% of acute rejection and 98.96% of chronic rejection episodes, respectively. We were able to identify serum protein fingerprints in small sample sizes of recipients with renal allograft rejection and establish the models for diagnosis of renal allograft rejection. This preliminary study demonstrated that proteomics is an emerging tool for early diagnosis of renal allograft rejection and helps us to better understand the pathogenesis of disease process.

  19. Investigation of the particle selectivity of a traveling potential wave; neon isotope separation with the Solitron process. Final report

    International Nuclear Information System (INIS)

    Lowder, R.S.

    1994-01-01

    The specific goal of this three year effort was to investigate this novel isotope separation process itself: to determine whether isotopes could indeed be separated and, if so, with what limitations--space charge effects, instabilities, and, in particular, with what throughput limitations. Termed the Solitron process, the concept is based on the strong isotopic variation in wave/ion interaction for a potential wave passing through an ion beam when the wave speed is near the ion speed. The ion's charge-to-mass ratio determines not only which ions are picked up by the wave but also the final energy of those ions that are picked up (accelerated to a higher energy); thus, this method can be used for isotope separation. Much progress was made regarding separation and throughput, concluding that separation works well in conjunction with electrostatic focusing used to obtain enough throughput (enough beam current) to make a practical device. The next step would likely be a production device, although development of an appropriate metal ion source would be useful. Funding is an issue; development cost estimates run around two million dollars for a market only several times that cost. Although there is much concern about the future supply of isotopes such as could be produced by the Solitron process, as well as costs, at present the supply from Oak Ridge and Russian sources is adequate for US needs. Should demand grow, these LDRD studies would strongly support proposals for further development of this Solitron process and help assure its likely success. For example, a point design for a magnesium mission was formulated to obtain a consistent set of design numbers that would optimize performance without pushing any constraints seen in these studies. A similar design could be formulated for other missions (magnesium was just a convenient target)

  20. Nicotinamide-NAD sequence: redox process and related behavior, behavior and properties of intermediate and final products

    International Nuclear Information System (INIS)

    Elving, P.J.; Schmakel, C.O.; Santhanam, K.S.V.

    1976-01-01

    Illustrations of the application of analytical chemical techniques to the study of chemical phenomena are given. In particular, electrochemical techniques and methodology and, to a lesser extent, spectrophotometry were used to investigate the solution behavior, adsorption, redox processes including coupled chemical reactions, and allied aspects of biologically significant compounds and of their intermediate and final redox products, e.g., the behavior of the free radicals produced by initial one-electron processes. This approach is illustrated by the consideration of the behavior in aqueous and nonaqueous media of a sequence of compounds ranging from nicotinamide (3-carbamoylpyridine) to NAD + and NADP + ; the latter compounds function as coenzymes for the pyridinoproteins which are principal components in the Krebs citric acid cycle and in the electron transport chain in biological redox reactions. The discussion is presented under the following section headings: interpretation of electrochemical behavior; mechanistic patterns; kinetic aspects of charge-transfer and chemical reactions; correlation with theoretically calculated parameters; and, mechanisms of biological oxidation-reduction reactions. The use of pulse radiolysis, chronopotentiometric, and cyclic voltammetric methods in studies on free radical dimerization rates is reviewed in the discussion of the kinetic aspects of charge-transfer and chemical reactions. (188 references)

  1. Total lymphoid irradiation for treatment of intractable cardiac allograft rejection

    International Nuclear Information System (INIS)

    Hunt, S.A.; Strober, S.; Hoppe, R.T.; Stinson, E.B.

    1991-01-01

    The ability of postoperative total lymphoid irradiation to reverse otherwise intractable cardiac allograft rejection was examined in a group of 10 patients in whom conventional rejection therapy (including pulsed steroids and monoclonal or polyclonal anti-T-cell antibody therapy) had failed to provide sustained freedom from rejection. Follow-up periods range from 73 to 1119 days since the start of total lymphoid irradiation. No patient died or sustained serious morbidity because of the irradiation. Three patients have had no further rejection (follow-up periods, 105 to 365 days). Two patients died--one in cardiogenic shock during the course of total lymphoid irradiation, the other with recurrent rejection caused by noncompliance with his medical regimen. Total lymphoid irradiation appears to be a safe and a moderately effective immunosuppressive modality for 'salvage' therapy of cardiac allograft rejection unresponsive to conventional therapy

  2. Acute rejection after kidney transplantation promotes graft fibrosis with elevated adenosine level in rat.

    Directory of Open Access Journals (Sweden)

    Mingliang Li

    Full Text Available Chronic allograft nephropathy is a worldwide issue with the major feature of progressive allograft fibrosis, eventually ending with graft loss. Adenosine has been demonstrated to play an important role in process of fibrosis. Our study aimed to investigate the relationship between adenosine and fibrosis in renal allograft acute rejection in rat.Wistar rats and SD rats were selected as experimental animals. Our study designed two groups. In the allograft transplantation group, kidneys of Wistar rats were orthotopically transplanted into SD rat recipients, the same species but not genetically identical, to induce acute rejection. Kidney transplantations of SD rats to SD rats which were genetically identical were served as the control. We established rat models and detected a series of indicators. All data were analyzed statistically. P<0.05 was considered statistically significant.Compared with the control group, levels of adenosine increased significantly in the allograft transplantation group, in which acute rejection was induced (P<0.05. Progressive allograft fibrosis as well as collagen deposition were observed.These findings suggested that level of adenosine was upregulated in acute rejection after kidney allograft transplantation in rat. Acute rejection may promote renal allograft fibrosis via the adenosine signaling pathways.

  3. Chronic Childhood Peer Rejection is Associated with Heightened Neural Responses to Social Exclusion During Adolescence.

    Science.gov (United States)

    Will, Geert-Jan; van Lier, Pol A C; Crone, Eveline A; Güroğlu, Berna

    2016-01-01

    This functional Magnetic Resonance Imaging (fMRI) study examined subjective and neural responses to social exclusion in adolescents (age 12-15) who either had a stable accepted (n = 27; 14 males) or a chronic rejected (n = 19; 12 males) status among peers from age 6 to 12. Both groups of adolescents reported similar increases in distress after being excluded in a virtual ball-tossing game (Cyberball), but adolescents with a history of chronic peer rejection showed higher activity in brain regions previously linked to the detection of, and the distress caused by, social exclusion. Specifically, compared with stably accepted adolescents, chronically rejected adolescents displayed: 1) higher activity in the dorsal anterior cingulate cortex (dACC) during social exclusion and 2) higher activity in the dACC and anterior prefrontal cortex when they were incidentally excluded in a social interaction in which they were overall included. These findings demonstrate that chronic childhood peer rejection is associated with heightened neural responses to social exclusion during adolescence, which has implications for understanding the processes through which peer rejection may lead to adverse effects on mental health over time.

  4. Acute and chronic rejection: compartmentalization and kinetics of counterbalancing signals in cardiac transplants.

    Science.gov (United States)

    Kaul, A M K; Goparaju, S; Dvorina, N; Iida, S; Keslar, K S; de la Motte, C A; Valujskikh, A; Fairchild, R L; Baldwin, W M

    2015-02-01

    Acute and chronic rejection impact distinct compartments of cardiac allografts. Intramyocardial mononuclear cell infiltrates define acute rejection, whereas chronic rejection affects large arteries. Hearts transplanted from male to female C57BL/6 mice undergo acute rejection with interstitial infiltrates at 2 weeks that resolve by 6 weeks when large arteries develop arteriopathy. These processes are dependent on T cells because no infiltrates developed in T cell-deficient mice and transfer of CD4 T cells restored T cell as well as macrophage infiltrates and ultimately neointima formation. Markers of inflammatory macrophages were up-regulated in the interstitium acutely and decreased as markers of wound healing macrophages increased chronically. Programmed cell death protein, a negative costimulator, and its ligand PDL1 were up-regulated in the interstitium during resolution of acute rejection. Blocking PDL1:PD1 interactions in the acute phase increased interstitial T cell infiltrates. Toll-like receptor (TLR) 4 and its endogenous ligand hyaluronan were increased in arteries with neointimal expansion. Injection of hyaluronan fragments increased intragraft production of chemokines. Our data indicate that negative costimulatory pathways are critical for the resolution of acute interstitial infiltrates. In the arterial compartment recognition of endogenous ligands including hyaluronan by the innate TLRs may support the progression of arteriopathy. © Copyright 2015 The American Society of Transplantation and the American Society of Transplant Surgeons.

  5. CD28 Family and Chronic Rejection: “To Belatacept...and Beyond!”

    Directory of Open Access Journals (Sweden)

    Marcos V. Silva

    2012-01-01

    Full Text Available Kidneys are one of the most frequently transplanted human organs. Immunosuppressive agents may prevent or reverse most acute rejection episodes; however, the graft may still succumb to chronic rejection. The immunological response involved in the chronic rejection process depends on both innate and adaptive immune response. T lymphocytes have a pivotal role in chronic rejection in adaptive immune response. Meanwhile, we aim to present a general overview on the state-of-the-art knowledge of the strategies used for manipulating the lymphocyte activation mechanisms involved in allografts, with emphasis on T-lymphocyte costimulatory and coinhibitory molecules of the B7-CD28 superfamily. A deeper understanding of the structure and function of these molecules improves both the knowledge of the immune system itself and their potential action as rejection inducers or tolerance promoters. In this context, the central role played by CD28 family, especially the relationship between CD28 and CTLA-4, becomes an interesting target for the development of immune-based therapies aiming to increase the survival rate of allografts and to decrease autoimmune phenomena. Good results obtained by the recent development of abatacept and belatacept with potential clinical use aroused better expectations concerning the outcome of transplanted patients.

  6. In-111-labeled leukocytes in the diagnosis of rejection and cytomegalovirus infection in renal transplant patients

    International Nuclear Information System (INIS)

    Forstrom, L.A.; Loken, M.K.; Cook, A.; Chandler, R.; McCullough, J.

    1981-01-01

    Indium-111-labeled (In-111) leukocytes have been shown to be useful in the localization of inflammatory processes, including renal transplant rejection. Using previously reported labeling methods, 63 studies with this agent have been performed in 53 renal transplant patients. Indications for study included suspected rejection or cytomegalovirus (CMV) infection. Studies were performed in 33 men and 20 women, with ages ranging from 6 to 68 years. Autologous cells were normally used for labeling, although leukocytes obtained from ABO-compatible donors were used in three subjects. Rectilinear scanner and/or scintillation camera images were obtained at 24 hours after intravenous administration of 0.1 to 0.6 mCi of In-111-leukocytes. There was abnormal uptake of In-111-leukocytes in the transplanted kidney in 11 of 15 cases of rejection. In three additional cases of increased transplant uptake, CMV infection was present in two. Abnormal lung uptake was present in 13 of 14 patients with CMV infection. In four additional cases, increased lung uptake was associated with other pulmonary inflammatory disease. Increased lung activity was not seen in patients with uncomplicated transplant rejection. These results suggest that In-111-leukocyte imaging may be useful in the differential diagnosis of rejection versus CMV infection in renal transplant patients

  7. In-111-labeled leukocytes in the diagnosis of rejection and cytomegalovirus infection in renal transplant patients

    International Nuclear Information System (INIS)

    Forstrom, L.A.; Loken, M.K.; Cook, A.; Chandler, R.; McCullough, J.

    1981-01-01

    Indium-111-labelled (In-111) leukocytes have been shown to be useful in the localization of inflammatory processes, including renal transplant rejection. Using previously reported labelling methods, 63 studies with this agent have been performed in 53 renal transplant patients. Indications for study included suspected rejection or cytomegalovirus (CMV) infection. Studies were performed in 33 men and 20 women, with ages ranging from 6 to 68 years. Autologous cells were normally used for labeling, although leukocytes obtained from ABO-compatible donors were used in three subjects. Rectilinear scanner and/or scintillation camera images were obtained at 24 hours after intravenous administration of 0.1 to 0.6 mCi of In-111 leukocytes. There was abnormal uptake of In-111-leukocytes in the transplanted kidney in 11 of 15 cases of rejection. In three additional cases of increased transplant uptake, CMV infection was present in two. Abnormal lung uptake was present in 13 of 14 patients with CMV infection. In four additional cases, increased lung uptake was associated with other pulmonary inflammatory disease. Increased lung activity was not seen in patients with uncomplicated transplant rejection. These results suggest that In-111-leukocyte imaging may be useful in the differential diagnosis of rejection versus CMV infection in renal transplant patients

  8. Cell-Free DNA and Active Rejection in Kidney Allografts.

    Science.gov (United States)

    Bloom, Roy D; Bromberg, Jonathan S; Poggio, Emilio D; Bunnapradist, Suphamai; Langone, Anthony J; Sood, Puneet; Matas, Arthur J; Mehta, Shikha; Mannon, Roslyn B; Sharfuddin, Asif; Fischbach, Bernard; Narayanan, Mohanram; Jordan, Stanley C; Cohen, David; Weir, Matthew R; Hiller, David; Prasad, Preethi; Woodward, Robert N; Grskovic, Marica; Sninsky, John J; Yee, James P; Brennan, Daniel C

    2017-07-01

    Histologic analysis of the allograft biopsy specimen is the standard method used to differentiate rejection from other injury in kidney transplants. Donor-derived cell-free DNA (dd-cfDNA) is a noninvasive test of allograft injury that may enable more frequent, quantitative, and safer assessment of allograft rejection and injury status. To investigate this possibility, we prospectively collected blood specimens at scheduled intervals and at the time of clinically indicated biopsies. In 102 kidney recipients, we measured plasma levels of dd-cfDNA and correlated the levels with allograft rejection status ascertained by histology in 107 biopsy specimens. The dd-cfDNA level discriminated between biopsy specimens showing any rejection (T cell-mediated rejection or antibody-mediated rejection [ABMR]) and controls (no rejection histologically), P rejection at a cutoff of 1.0% dd-cfDNA were 61% and 84%, respectively. The AUC for discriminating ABMR from samples without ABMR was 0.87 (95% CI, 0.75 to 0.97). Positive and negative predictive values for ABMR at a cutoff of 1.0% dd-cfDNA were 44% and 96%, respectively. Median dd-cfDNA was 2.9% (ABMR), 1.2% (T cell-mediated types ≥IB), 0.2% (T cell-mediated type IA), and 0.3% in controls ( P =0.05 for T cell-mediated rejection types ≥IB versus controls). Thus, dd-cfDNA may be used to assess allograft rejection and injury; dd-cfDNA levels rejection (T cell-mediated type ≥IB or ABMR) and levels >1% indicate a probability of active rejection. Copyright © 2017 by the American Society of Nephrology.

  9. High-testosterone men reject low ultimatum game offers

    OpenAIRE

    Burnham, Terence C

    2007-01-01

    The ultimatum game is a simple negotiation with the interesting property that people frequently reject offers of ‘free’ money. These rejections contradict the standard view of economic rationality. This divergence between economic theory and human behaviour is important and has no broadly accepted cause. This study examines the relationship between ultimatum game rejections and testosterone. In a variety of species, testosterone is associated with male seeking dominance. If low ultimatum game...

  10. A Delta Operator Approach for the Discrete-Time Active Disturbance Rejection Control on Induction Motors

    Directory of Open Access Journals (Sweden)

    John Cortés-Romero

    2013-01-01

    Full Text Available The problem of active disturbance rejection control of induction motors is tackled by means of a generalized PI observer based discrete-time control, using the delta operator approach as the methodology of analyzing the sampled time process. In this scheme, model uncertainties and external disturbances are included in a general additive disturbance input which is to be online estimated and subsequently rejected via the controller actions. The observer carries out the disturbance estimation, thus reducing the complexity of the controller design. The controller efficiency is tested via some experimental results, performing a trajectory tracking task under load variations.

  11. Recovery of Rare Earth Elements from Coal and Coal Byproducts via a Closed Loop Leaching Process: Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Peterson, Richard [Battelle Memorial Inst., Columbus, OH (United States); Heinrichs, Michael [Battelle Memorial Inst., Columbus, OH (United States); Argumedo, Darwin [Battelle Memorial Inst., Columbus, OH (United States); Taha, Rachid [Battelle Memorial Inst., Columbus, OH (United States); Winecki, Slawomir [Battelle Memorial Inst., Columbus, OH (United States); Johnson, Kathryn [Battelle Memorial Inst., Columbus, OH (United States); Lane, Ann [Battelle Memorial Inst., Columbus, OH (United States); Riordan, Daniel [Battelle Memorial Inst., Columbus, OH (United States)

    2017-08-31

    REEs using the ADP technology. In AOI 1, Ohio coal sources with the potential to provide a consistent source of rare earth element concentrations above 300 parts per million will be identified. Coal sample inventories from West Virginia and Pennsylvania will also be assessed for purposes of comparison. Three methods of preparing the coal ash will be evaluated for their potential to enhance the technical feasibility and economics of REE recovery. Three sources of coal ash are targeted for evaluation of the economics of REE recovery in this project: (1) coal ash from power generation stations, to include fly ash and/or bottom ash, (2) ash generated in a lower temperature ashing process, and (3) ash residual from Battelle’s coal liquefaction process. Making use of residual ash from coal liquefaction processes directly leverages work currently being conducted by Battelle for DOE NETL in response to DE-FOA-0000981 entitled “Greenhouse Gas Emissions Reductions Research and Development Leading to Cost-Competitive Coal-to-Liquids Based Jet Fuel Production.” Using the sample characterization results and regional information regarding REE concentration, availability and cost, a TEA will be developed. The previously generated laboratory testing results for leaching and REE recovery via the ADP will be used to perform the TEA, along with common engineering assumptions for scale up of equipment and labor costs. Finally, upon validation of the economic feasibility of the process by the TEA, limited laboratory testing will be performed to support the design of a bench scale system. In a future project phase, it is envisioned that the bench scale system will be constructed and operated to prove the process on a continuous basis.

  12. Novel Techniques for Background / Foreground Rejection in Particle Instruments

    Data.gov (United States)

    National Aeronautics and Space Administration — The Novel Techniques for Background / Foreground Rejection in Particle Instruments project addresses the need for signal contamination and background signal...

  13. Rejection Sensitivity, Jealousy, and the Relationship to Interpersonal Aggression.

    Science.gov (United States)

    Murphy, Anna M; Russell, Gemma

    2018-07-01

    The development and maintenance of interpersonal relationships lead individuals to risk rejection in the pursuit of acceptance. Some individuals are predisposed to experience a hypersensitivity to rejection that is hypothesized to be related to jealous and aggressive reactions within interpersonal relationships. The current study used convenience sampling to recruit 247 young adults to evaluate the relationship between rejection sensitivity, jealousy, and aggression. A mediation model was used to test three hypotheses: Higher scores of rejection sensitivity would be positively correlated to higher scores of aggression (Hypothesis 1); higher scores of rejection sensitivity would be positively correlated to higher scores of jealousy (Hypothesis 2); jealousy would mediate the relationship between rejection sensitivity and aggression (Hypothesis 3). Study results suggest a tendency for individuals with high rejection sensitivity to experience higher levels of jealousy, and subsequently have a greater propensity for aggression, than individuals with low rejection sensitivity. Future research that substantiates a link between hypersensitivity to rejection, jealousy, and aggression may provide an avenue for prevention, education, or intervention in reducing aggression within interpersonal relationships.

  14. Community rejection following sexual assault as ‘forced migration’

    OpenAIRE

    AJ Morgen

    2013-01-01

    When women are banished from their communities following sexual assault, this rejection should be considered an act of forced migration by the administrators of truth commission reparations programmes.

  15. Evaluation energy efficiency of bioconversion knot rejects to ethanol in comparison to other thermochemically pretreated biomass

    Science.gov (United States)

    Zhaojiang Wang; Menghua Qin; J.Y. Zhu; Guoyu Tian; Zongquan. Li

    2013-01-01

    Rejects from sulfite pulp mill that otherwise would be disposed of by incineration were converted to ethanol by a combined physical–biological process that was comprised of physical refining and simultaneous saccharification and fermentation (SSF). The energy efficiency was evaluated with comparison to thermochemically pretreated biomass, such as those pretreated by...

  16. Developing and testing ScrollQuest: A video game targeting rejection sensitivity in adolescents

    NARCIS (Netherlands)

    Tuijnman, A.; Granic, I.; Whitkin, J.; Engels, R.C.M.E.

    2017-01-01

    Depression affects a large proportion of adolescents and current interventions only have moderate effects. With the potential of video games for emotional and mental health in mind, we developed a video game for rejection sensitivity, which is a major risk factor for depression. A process of

  17. An audit of rejected repeated x-ray films as a quality assurance element in a radiology department.

    Science.gov (United States)

    Eze, K C; Omodia, N; Okegbunam, B; Adewonyi, T; Nzotta, C C

    2008-12-01

    To find out the causes, number, percentage and sizes of rejected radiographic films with a view of adopting measures that will reduce the rate and number of rejected films. Radiology Department of a University Teaching Hospital. Over a two-year period (1st April 2002 to 31st March 2004), the total number of x-ray films utilized for radiographic examinations, rejected films and sizes of rejected films were collected retrospectively from the medical record of radiology department. All the rejected films were viewed by a radiologist and three radiographers for the causes of the rejects which was arrived at by consensus. The data was analysed. A total of 15,095 films were used in the study period and 1,338 films (8.86%) were rejected or wasted. The rate of rejected films varied from 7.69% to 13.82% with average of 8.86%. The greatest cause of film rejects was radiographers' faults 547 (40.88%), followed by equipments faults 255 (19.06%), and patients' faults 250 (18.90%). The highest reject rate (13.82%) was for films used for examination of the spine (15 x 30) cm size. This is followed by 9.92% for skull (18 x 24) cm films and 8.83% for small sized films (24 x 30) cm used for paediatric patients. Of a total of 1,338 rejected films, 1276 (95.37%) additional exposure were done to obtain the basic desired diagnostic information involving 1151 patients; 885 (76.89%) of these patients needed at least one additional hospital visit to take the repeat exposure. Rejected films are not billable; patients receive additional radiation and may even come to hospital in another day for the repeat. Radiographer's work is increased as well as that of the support staff. The waiting room may be congested and waiting time increased. The cost of processing chemical and films are increased, thus if work is quantified in monetary terms, the cost of repeats is high. Rejected-repeated film analysis is cheap, simple, practicable, easy to interpret and an effective indictor of quality assurance

  18. Partnew - New solvent extraction processes for minor actinides - final report; Partnew - Nouveaux procedes d'extraction par solvant pour les actinides mineurs - rapport final

    Energy Technology Data Exchange (ETDEWEB)

    Madic, C.; Testard, F.; Hudson, M.J.; Liljenzin, J.O.; Christiansen, B.; Ferrando, M.; Facchini, A.; Geist, A.; Modolo, G.; Gonzalez-Espartero, A.; Mendoza, J. de

    2004-07-01

    The objectives of the European project PARTNEW were to define solvent extraction processes for the partitioning of the minor actinides, Am and Cm, from the aqueous high active raffinate or high active concentrate issuing the reprocessing of nuclear spent fuels by the PUREX process. Eleven laboratories participated to the research: 1/ CEA-DEN (Marcoule), 2/ CEA-DSM (Saclay), 3/ UREAD (U.K.), 4/ CTU (Sweden), 5/ ITU (Germany), 6/ ENEA (Italy), 7/ PoliMi (Italy), 8/ FZK-INE (Germany), 9/ FZJ-ISR (Germany), 10/ CIEMAT (Spain) and 11/ UAM (Spain). The research was organised into eight work packages (WP): Basic and applied DIAMEX studies, using diamide extractants for the co-extraction of actinides(III) (An(III)) and lanthanides(III) (Ln(III)) nitrates (WP1 and WP2), Basic and applied SANEX studies based on the use of polydentate N-ligands for the An(III)/Ln(III) separation (WP3 and WP4), Basic and applied SANEX studies based on the use of synergistic mixtures made of bis-(chloro-phenyl)-di-thio-phosphinic acid + neutral O-bearing ligand, (WP5 and WP6), Basic SANEX studies for the An(III)/Ln(III) separation, based on the use of new S-bearing ligands, Basic and applied studies for the Am(III)/Cm(III) separation. The work done in the fundamental and applied domains was very fruitful. Several processes have been successfully tested with genuine high active raffinates and concentrate. (authors)

  19. Simulation of disturbance rejection control of half-car active suspension system using active disturbance rejection control with decoupling transformation

    Science.gov (United States)

    Hasbullah, Faried; Faris, Waleed F.

    2017-12-01

    In recent years, Active Disturbance Rejection Control (ADRC) has become a popular control alternative due to its easy applicability and robustness to varying processes. In this article, ADRC with input decoupling transformation (ADRC-IDT) is proposed to improve ride comfort of a vehicle with an active suspension system using half-car model. The ride performance of the ADRC-IDT is evaluated and compared with decentralized ADRC control as well as the passive system. Simulation results show that both ADRC and ADRC-IDT manage to appreciably reduce body accelerations and able to cope well with varying conditions typically encountered in an active suspension system. Also, it is sufficient to control only the body motions with both active controllers to improve ride comfort while maintaining good road holding and small suspension working space.

  20. Evaluation of gasification and gas cleanup processes for use in molten carbonate fuel cell power plants. Final report. [Contains lists and evaluations of coal gasification and fuel gas desulfurization processes

    Energy Technology Data Exchange (ETDEWEB)

    Jablonski, G.; Hamm, J.R.; Alvin, M.A.; Wenglarz, R.A.; Patel, P.

    1982-01-01

    This report satisfies the requirements for DOE Contract AC21-81MC16220 to: List coal gasifiers and gas cleanup systems suitable for supplying fuel to molten carbonate fuel cells (MCFC) in industrial and utility power plants; extensively characterize those coal gas cleanup systems rejected by DOE's MCFC contractors for their power plant systems by virtue of the resources required for those systems to be commercially developed; develop an analytical model to predict MCFC tolerance for particulates on the anode (fuel gas) side of the MCFC; develop an analytical model to predict MCFC anode side tolerance for chemical species, including sulfides, halogens, and trace heavy metals; choose from the candidate gasifier/cleanup systems those most suitable for MCFC-based power plants; choose a reference wet cleanup system; provide parametric analyses of the coal gasifiers and gas cleanup systems when integrated into a power plant incorporating MCFC units with suitable gas expansion turbines, steam turbines, heat exchangers, and heat recovery steam generators, using the Westinghouse proprietary AHEAD computer model; provide efficiency, investment, cost of electricity, operability, and environmental effect rankings of the system; and provide a final report incorporating the results of all of the above tasks. Section 7 of this final report provides general conclusions.

  1. Corneal allograft rejection: Risk factors, diagnosis, prevention, and treatment

    Directory of Open Access Journals (Sweden)

    Dua Harminder

    1999-01-01

    Full Text Available Recent advances in corneal graft technology, including donor tissue retrieval, storage and surgical techniques, have greatly improved the clinical outcome of corneal grafts. Despite these advances, immune mediated corneal graft rejection remains the single most important cause of corneal graft failure. Several host factors have been identified as conferring a "high risk" status to the host. These include: more than two quadrant vascularisation, with associated lymphatics, which augment the afferent and efferent arc of the immune response; herpes simplex keratitis; uveitis; silicone oil keratopathy; previous failed (rejected grafts; "hot eyes"; young recipient age; and multiple surgical procedures at the time of grafting. Large grafts, by virtue of being closer to the host limbus, with its complement of vessels and antigen-presenting Langerhans cells, also are more susceptible to rejection. The diagnosis of graft rejection is entirely clinical and in its early stages the clinical signs could be subtle. Graft rejection is largely mediated by the major histocompatibility antigens, minor antigens and perhaps blood group ABO antigens and some cornea-specific antigens. Just as rejection is mediated by active immune mediated events, the lack of rejection (tolerance is also sustained by active immune regulatory mechanisms. The anterior chamber associated immune deviation (ACAID and probably, conjunctiva associated lymphoid tissue (CALT induced mucosal tolerance, besides others, play an important role. Although graft rejection can lead to graft failure, most rejections can be readily controlled if appropriate management is commenced at the proper time. Topical steroids are the mainstay of graft rejection management. In the high-risk situations however, systemic steroids, and other immunosuppressive drugs such as cyclosporin and tacrolimus (FK506 are of proven benefit, both for treatment and prevention of rejection.

  2. Temperature and final characteristics of composting process of the Municipal solid wastes; Evolucion de la temperatura y caracteristicas finales del co-compostaje de residuos solidos urbanos

    Energy Technology Data Exchange (ETDEWEB)

    Porcel, O.; Leon, J.J. de; Revilla, J.; Dobao, M.M.; Ruiz, J.L. [Departamento de Quimica Agricola y Edafologia, Universidad de Cordoba, cordoba (Spain)

    1996-06-01

    In this paper it has been studied the evolution of temperature in two depth of three piles during the composting process using the organic matter of the Municipal Solid Waste from Cordoba (Spain) from the selective harvest. The cited mixtures were composed of organic matter (<50 mm), sludge from the water treatment plant, pruning garden and bark of pine (bunking). Almost it has been obtained the yield of the composting piles and the agronomic quality of the compost obtained. The mixture organic matter <50 mm+pruning arden+bunking (M.P.B.) shoved the best index. (Author) 15 refs.

  3. Final disposal of spent nuclear fuel in Sweden. Some unresolved issues and challenges in the design and implementation of the forthcoming planning and EIA processes

    International Nuclear Information System (INIS)

    Bjarnadottir, H.; Hilding-Rydevik, T.

    2001-06-01

    The aim of the study is to highlight some unresolved and challenging issues in the forthcoming approximately six year long Environmental Impact Assessment (EIA) and planning process of the long-term disposal of spent nuclear fuel in Sweden. Different international and Nordic experiences of the processes for final disposal as well as from other development of similar scope, where experiences assumed to be of importance for final disposal of nuclear waste, have been described. Furthermore, issues relating to 'good EIA practice' as well as certain aspects of planning theory have also been presented. The current Swedish situation for the planning and EIA process of the final disposal of spent nuclear fuel was also been summarized. These different 'knowledge areas' have been compared and measured against our perception of the expectations towards the forthcoming process, put forward by different Swedish actors in the field. The result is a presentation of a number of questions and identification issues that the authors consider need special attention in the design and conduction of the planning and EIA process. The study has been realized through a literature survey and followed by reading and analysis of the written material. The main focus of the literature search was on material describing planning processes, actor perspectives and EIA. Material and literature on the technical and scientific aspects of spent nuclear fuel disposal was however deliberately avoided. There is a wealth of international and Swedish literature concerning final disposal of spent nuclear fuel - concerning both technical issues and issues concerning for example public participation and risk perception. But material of a more systematic and comparative nature (relating to both empirical and theoretical issues, and to practical experiences) in relation to EIA processes and communicative planning for final disposal of spent nuclear fuel seems to be more sparsely represented. Our perception of

  4. Cast iron components for the wind power industry. Development of resource saving products and processes in global competition. Final report; Gjutgods till vindkraftsindustrin. Utveckling av resurssnaala produkter och processer i global konkurrens. Slutrapport

    Energy Technology Data Exchange (ETDEWEB)

    Gustavsson, Conny; Gustafsson, Ingela; Petku, Damir [Swedish Foundry Association, Joenkoeping (SE)] [and others

    2006-01-15

    The demand for large cast components in ductile iron for wind power plants has increased strongly. As wind power plants become larger, today up to 4-5 MW, the components grow with them. Weights around 20 tons become common, and are demanded in growing numbers. For most Swedish foundries production of such size components is impossible, but for a few, accustomed to large castings a new growing market has opened. Higher prices for scrap and electricity is however a menace to profit. This project concentrates on factors that may optimize the flow in production, reduce rejections, reduce the consumption of new sand, and to reduce energy consumption in all processes. The project has resulted in ten separate reports, that are included in this publication.

  5. Quantum Communication Using Coherent Rejection Sampling

    Science.gov (United States)

    Anshu, Anurag; Devabathini, Vamsi Krishna; Jain, Rahul

    2017-09-01

    Compression of a message up to the information it carries is key to many tasks involved in classical and quantum information theory. Schumacher [B. Schumacher, Phys. Rev. A 51, 2738 (1995), 10.1103/PhysRevA.51.2738] provided one of the first quantum compression schemes and several more general schemes have been developed ever since [M. Horodecki, J. Oppenheim, and A. Winter, Commun. Math. Phys. 269, 107 (2007); , 10.1007/s00220-006-0118-xI. Devetak and J. Yard, Phys. Rev. Lett. 100, 230501 (2008); , 10.1103/PhysRevLett.100.230501A. Abeyesinghe, I. Devetak, P. Hayden, and A. Winter, Proc. R. Soc. A 465, 2537 (2009), 10.1098/rspa.2009.0202]. However, the one-shot characterization of these quantum tasks is still under development, and often lacks a direct connection with analogous classical tasks. Here we show a new technique for the compression of quantum messages with the aid of entanglement. We devise a new tool that we call the convex split lemma, which is a coherent quantum analogue of the widely used rejection sampling procedure in classical communication protocols. As a consequence, we exhibit new explicit protocols with tight communication cost for quantum state merging, quantum state splitting, and quantum state redistribution (up to a certain optimization in the latter case). We also present a port-based teleportation scheme which uses a fewer number of ports in the presence of information about input.

  6. Smith predictor-based multiple periodic disturbance compensation for long dead-time processes

    Science.gov (United States)

    Tan, Fang; Li, Han-Xiong; Shen, Ping

    2018-05-01

    Many disturbance rejection methods have been proposed for processes with dead-time, while these existing methods may not work well under multiple periodic disturbances. In this paper, a multiple periodic disturbance rejection is proposed under the Smith predictor configuration for processes with long dead-time. One feedback loop is added to compensate periodic disturbance while retaining the advantage of the Smith predictor. With information of the disturbance spectrum, the added feedback loop can remove multiple periodic disturbances effectively. The robust stability can be easily maintained through the rigorous analysis. Finally, simulation examples demonstrate the effectiveness and robustness of the proposed method for processes with long dead-time.

  7. Refusals and Rejections: Designing Messages to Serve Multiple Goals.

    Science.gov (United States)

    Saeki, Mimako; O'Keefe, Barbara J.

    1994-01-01

    Tests a rational model of the elaboration of themes found in rejection messages, using Japanese and American participants. Finds partial support for the initial rational model but notes two key revisions: identifies two new themes in rejection messages and suggests substantial differences in the way Americans and Japanese elaborate themes to serve…

  8. Perception of Parental Acceptance and Rejection among Swedish University Students.

    Science.gov (United States)

    Kitahara, Michio

    1987-01-01

    Results of administering the Parental Acceptance-Rejection and Personality Assessment Questionnaires to 71 Swedish university students showed significant relationships between various forms of parental rejection in childhood and negative personality assessment of the self as an adult. Females showed more dependence and emotional instability than…

  9. Indium-labeled platelet uptake in rejecting renal transplants

    International Nuclear Information System (INIS)

    Chandler, S.T.; Buckels, J.; Hawker, R.J.; Smith, N.; Barnes, A.D.; McCollum, C.N.

    1983-01-01

    The uptake of 111 In autologous platelets in transplanted kidneys was measured in 16 patients shortly after operation. Each patient was then observed for two years. When transplant radioactivity had increased, despite treatment for acute rejection, the kidney was ultimately lost because of rejection

  10. Peer victimization and peer rejection during early childhood

    Science.gov (United States)

    Godleski, Stephanie A.; Kamper, Kimberly E.; Ostrov, Jamie M.; Hart, Emily J.; Blakely-McClure, Sarah J.

    2014-01-01

    Objective The development and course of the subtypes of peer victimization is a relatively understudied topic despite the association of victimization with important developmental and clinical outcomes. Moreover, understanding potential predictors, such as peer rejection and emotion regulation, in early childhood may be especially important to elucidate possible bi-directional pathways between relational and physical victimization and rejection. The current study (N = 97) was designed to explore several gaps and limitations in the peer victimization and peer rejection literature. In particular, the prospective associations between relational and physical victimization and peer rejection over the course of 3.5 months during early childhood (i.e., 3- to 5- years-old) were investigated in an integrated model. Method The study consisted of 97 (42 girls) preschool children recruited from four early childhood schools in the northeast of the US. Using observations, research assistant report and teacher report, relational and physical aggression, relational and physical victimization, peer rejection, and emotion regulation were measured in a short-term longitudinal study. Path analyses were conducted to test the overall hypothesized model. Results Peer rejection was found to predict increases in relational victimization. In addition, emotion regulation was found to predict decreases in peer rejection and physical victimization. Conclusions Implications for research and practice are discussed, including teaching coping strategies for peer rejection and emotional distress. PMID:25133659

  11. 48 CFR 14.404-2 - Rejection of individual bids.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 1 2010-10-01 2010-10-01 false Rejection of individual... of individual bids. (a) Any bid that fails to conform to the essential requirements of the invitation... total price of the bid, but the prices for individual line items as well. (g) Any bid may be rejected if...

  12. 48 CFR 814.404-2 - Rejection of individual bids.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Rejection of individual... Rejection of individual bids. (a) When a contracting officer finds a bid that is being considered for an... nonresponsive an individual bid that is not in compliance with the Government's bid acceptance time, since...

  13. Prevalence and characteristics of foal rejection in Arabian mares.

    Science.gov (United States)

    Juarbe-Díaz, S V; Houpt, K A; Kusunose, R

    1998-09-01

    Separate surveys of Thoroughbred, Paint, and Arabian mare owners revealed a higher than expected rate of foal rejection in Arabian mares. A behavioural history form was submitted by owners of foal rejecting and nonrejecting Arabian mares, and maternal behaviour and management practices compared. Four generation pedigrees of rejecting and nonrejecting Arabian mares were also examined. Foal rejecting mares were more likely to avoid, threaten, squeal at, chase, bite, and kick their foals post partum than nonrejecting mares. Nonrejecting mares were more likely to lick, nicker and defend their foals post partum than rejecting mares. No statistically significant relationship was found between foal rejection and the type of breeding method (natural vs. artificial insemination), the presence of people at birth, the presence of nearby horses at birth, or assistance of the first nursing bout. The presence at least once of 1 of 2 related sires was statistically higher in the pedigrees of rejecting vs. nonrejecting mares. Inherited and learned or environmental factors are likely to affect the expression of foal rejection behaviour.

  14. Acute antibody-mediated rejection in pancreas and kidney transplantation

    NARCIS (Netherlands)

    Kort, Hanneke de

    2013-01-01

    In this thesis, acute rejection after kidney, simultaneous pancreas and kidney (SPKT), and islets of Langerhans transplantation was addressed. The focus is on acute antibody-mediated rejection (AMR) after transplantation and on a potential strategy using cellular immune modulation to prevent acute

  15. Apoptosis of acinar cells in pancreas allograft rejection

    NARCIS (Netherlands)

    Boonstra, J. G.; Wever, P. C.; Laterveer, J. C.; Bruijn, J. A.; van der Woude, F. J.; ten Berge, I. J.; Daha, M. R.

    1997-01-01

    BACKGROUND: Recently it has been recognized that apoptosis of target cells may occur during liver and kidney allograft rejection and is probably induced by infiltrating cells. Pancreas rejection is also characterized by a cellular infiltrate, however, the occurrence of apoptosis has not been

  16. Developments and studies on the (T)HMC processes in a final repository for heat generating radioactive wastes. Synthesis and final report; Entwicklungen und Untersuchungen zu (T)HMC-Prozessen eines Endlagers fuer Waerme entwickelnde radioaktive Abfaelle. Synthese und Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Weyand, Torben [Bonn Univ. (Germany); Bracke, Guido; Fischer, Heidemarie; Frieling, Gerd; Hansmeier, Christina; Hotzel, Stephan; Kock, Ingo; Seher, Holger

    2014-10-15

    The report on developments and studies on the (T)HMC (thermal-hydraulic-mechanical-chemical) processes in a final repository for heat generating radioactive wastes covers the following topics: description of the projects, applied codes: TOUGH2, FLAC3D, TOUGH2 and FLAC3D, TOUHREACT/PetraSim, MARNIE, PHREEQC, geochemists workbench, SUSA; safety relevant singular processes in the transition phase, uncertainties due to process interactions, coupling of mass transport and geochemical equilibria, further developments and application of numerical simulations in the transition phase.

  17. Uptake of myocardial imaging agents by rejected hearts

    International Nuclear Information System (INIS)

    Bergsland, J.; Carr, E.A.; Carroll, M.; Wright, J.W.; Feldman, M.J.; Massucci, J.; Bhayana, J.N.; Gona, J.M.

    1985-01-01

    Technetium 99 m pyrophosphate, Gallium 67 and Thallium 201 uptakes were measured in heterotopically transplanted rat hearts. Five days after transplantation, Technetium 99 m pyrophosphate, and Gallium 67 uptakes were significantly higher in allogeneic grafts than in syngeneic grafts. At an early stage of rejection (three days after transplantation), only Technetium 99 m pyrophosphate uptake in the left ventricle of allogeneic grafts showed a significant difference (p less than 0.04). At five days, Thallium 201 uptake was significantly lower in allo- than syngeneic grafts. There was a positive correlation between radionuclide uptake and histologic degree of rejection for Technetium 99 m pyrophosphate and Gallium 67 while Thallium 201 uptake correlated negatively. Analysis of variance revealed that hearts with no or minimal rejection had statistically different uptakes than hearts with mild to moderate rejection. These results suggest that uptake of imaging agents might be useful in the diagnosis of rejection of the transplanted heart

  18. Diagnosis of cardiac allograft rejection with MR imaging

    International Nuclear Information System (INIS)

    Soulen, R.L.; Fraser, C.D.; Hutchins, G.M.; Baumgartner, W.A.; Reitz, B.A.

    1987-01-01

    Serial MR images and endomyocardial biopsy specimens of heterotopic cervical cardiac allotransplants were obtained in six dogs during 2 weeks of immunosuppression followed by 1 week without such therapy. A surface coil and gated spin-echo technique were used. Myocardial intensity (MI) measurements and histopathologic interpretations were performed independently. All six dogs showed a decrease in MI between their first and second MR studies, while showing no rejection. One dog had no rejection and died; in five dogs studies gated to every other beat showed progressive increase in MI that correlated significantly with increasing rejection, though absolute MI values did not correlated with a specific biopsy score. Severe rejection also caused overt increase in myocardial mass. The MI in the early postoperative period may reflect reperfusion injury. Absolute intensity values cannot predict rejection. Serial studies in transplant patients may prove clinically useful

  19. High-testosterone men reject low ultimatum game offers.

    Science.gov (United States)

    Burnham, Terence C

    2007-09-22

    The ultimatum game is a simple negotiation with the interesting property that people frequently reject offers of 'free' money. These rejections contradict the standard view of economic rationality. This divergence between economic theory and human behaviour is important and has no broadly accepted cause. This study examines the relationship between ultimatum game rejections and testosterone. In a variety of species, testosterone is associated with male seeking dominance. If low ultimatum game offers are interpreted as challenges, then high-testosterone men may be more likely to reject such offers. In this experiment, men who reject low offers ($5 out of $40) have significantly higher testosterone levels than those who accept. In addition, high testosterone levels are associated with higher ultimatum game offers, but this second finding is not statistically significant.

  20. Study of a Multivariate Approach for the Background Rejection in the Scattering of Two Like-Charge $W^{\\pm}$ Bosons with the ATLAS Detector at the LHC

    CERN Document Server

    AUTHOR|(CDS)2100403; Kobel, Michael; Straessner, Arno

    This thesis presents the study of a multivariate approach for the background rejection in the scattering of two like-charge $W^{\\pm}$ bosons with the ATLAS detector at the Large Hadron Collider. The scattering process can be accessed through the measurement of purely electroweak production of two like-charge $W^{\\pm}$ bosons and two jets in the fully leptonic decay channel of the $W^{\\pm}$ bosons. Although the characteristic signature of the final state of this production process already reduces most Standard Model backgrounds, other processes exist that leave the same experimental signature in the detector. QCD-initiated production of a $W^{\\pm}$ boson and a $Z$ boson in association with two jets with leptonic decay of the $W^{\\pm}$ and the $Z$ boson accounts for the largest background contribution. Thus, the focus of this thesis is set on the rejection of this background. As a very promising technique for this classification problem, boosted decision trees are studied in this thesis. The variable ranking of...

  1. Eosinophil count, allergies, and rejection in pediatric heart transplant recipients.

    Science.gov (United States)

    Arbon, Kate S; Albers, Erin; Kemna, Mariska; Law, Sabrina; Law, Yuk

    2015-08-01

    Allograft rejection and long-term immunosuppression remain significant challenges in pediatric heart transplantation. Pediatric recipients are known to have fewer rejection episodes and to develop more allergic conditions than adults. A T-helper 2 cell dominant phenotype, manifested clinically by allergies and an elevated eosinophil count, may be associated with immunologic quiescence in transplant recipients. This study assessed whether the longitudinal eosinophil count and an allergic phenotype were associated with freedom from rejection. This single-center, longitudinal, observational study included 86 heart transplant patients monitored from 1994 to 2011. Post-transplant biannual complete blood counts, allergic conditions, and clinical characteristics related to rejection risk were examined. At least 1 episode of acute cellular rejection (ACR) occurred in 38 patients (44%), antibody-mediated rejection (AMR) occurred in 11 (13%), and 49 patients (57%) were diagnosed with an allergic condition. Patients with ACR or AMR had a lower eosinophil count compared with non-rejectors (p = 0.011 and p = 0.022, respectively). In the multivariable regression analysis, the presence of panel reactive antibodies to human leukocyte antigen I (p = 0.014) and the median eosinophil count (p = 0.011) were the only independent covariates associated with AMR. Eosinophil count (p = 0.010) and female sex (p = 0.009) were independent risk factors for ACR. Allergic conditions or young age at transplant were not protective from rejection. This study demonstrates a novel association between a high eosinophil count and freedom from rejection. Identifying a biomarker for low rejection risk may allow a reduction in immunosuppression. Further investigation into the role of the T-helper 2 cell phenotype and eosinophils in rejection quiescence is warranted. Copyright © 2015 International Society for Heart and Lung Transplantation. Published by Elsevier Inc. All rights reserved.

  2. Specimen rejection in laboratory medicine: Necessary for patient safety?

    Science.gov (United States)

    Dikmen, Zeliha Gunnur; Pinar, Asli; Akbiyik, Filiz

    2015-01-01

    The emergency laboratory in Hacettepe University Hospitals receives specimens from emergency departments (EDs), inpatient services and intensive care units (ICUs). The samples are accepted according to the rejection criteria of the laboratory. In this study, we aimed to evaluate the sample rejection ratios according to the types of pre-preanalytical errors and collection areas. The samples sent to the emergency laboratory were recorded during 12 months between January to December, 2013 in which 453,171 samples were received and 27,067 specimens were rejected. Rejection ratios was 2.5% for biochemistry tests, 3.2% for complete blood count (CBC), 9.8% for blood gases, 9.2% for urine analysis, 13.3% for coagulation tests, 12.8% for therapeutic drug monitoring, 3.5% for cardiac markers and 12% for hormone tests. The most frequent rejection reasons were fibrin clots (28%) and inadequate volume (9%) for biochemical tests. Clotted samples (35%) and inadequate volume (13%) were the major causes for coagulation tests, blood gas analyses and CBC. The ratio of rejected specimens was higher in the EDs (40%) compared to ICUs (30%) and inpatient services (28%). The highest rejection ratio was observed in neurology ICU (14%) among the ICUs and internal medicine inpatient service (10%) within inpatient clinics. We detected an overall specimen rejection rate of 6% in emergency laboratory. By documentation of rejected samples and periodic training of healthcare personnel, we expect to decrease sample rejection ratios below 2%, improve total quality management of the emergency laboratory and promote patient safety.

  3. Solid waste and the water environment in the new European Union perspective. Process analysis related to storage and final disposal

    Energy Technology Data Exchange (ETDEWEB)

    Marques, Marcia [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Chemical Engineering and Technology

    2000-11-01

    Processes that occur during storage and final disposal of solid waste were studied, with emphasis on physical and chemical aspects and their effects on the water environment, within the New European Union perspective for landfilling (Council Directive 1999/31/EC of 26 April 1999). In the new scenario, landfilling is largely restricted; waste treatments such as incineration, composting, recycling, storage and transportation of materials are intensified. Landfill sites are seen as industrial facilities rather than merely final disposal sites. Four main issues were investigated within this new scenario, in field- and full-scale, mostly at Spillepeng site, southern Sweden. (1) Adequacy of storage piles: Regarding the increasing demand for waste storage as fuel, the adequacy of storage in piles was investigated by monitoring industrial waste (IND) fuel compacted piles. Intense biodegradation activity, which raised the temperature into the optimum range for chemical oxidation reactions, was noticed during the first weeks. After about six months of storage, self-ignition occurred in one IND pile and one refuse derived fuel (RDF) pile. Heat, O{sub 2} and CO{sub 2} distribution at different depths of the monitored IND pile suggested that natural convection plays an important role in the degradation process by supplying oxygen and releasing heat. Storage techniques that achieve a higher degree of compaction, such as baling, are preferable to storage in piles. ( 2) Discharge from landfill for special waste: Regarding changes in the composition of the waste sent to landfills and the consequences for its hydrological performance in active and capped landfills, discharge from a full-scale landfill for special/hazardous waste (predominantly fly ash from municipal solid waste (MSW) incineration) was modelled using the U.S. EPA HELP model. Hydraulic properties of the special waste were compared with those from MSW. Lower practical field capacity and higher hydraulic conductivity at

  4. Solid waste and the water environment in the new European Union perspective. Process analysis related to storage and final disposal

    Energy Technology Data Exchange (ETDEWEB)

    Marques, Marcia [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Chemical Engineering and Technology

    2000-11-01

    Processes that occur during storage and final disposal of solid waste were studied, with emphasis on physical and chemical aspects and their effects on the water environment, within the New European Union perspective for landfilling (Council Directive 1999/31/EC of 26 April 1999). In the new scenario, landfilling is largely restricted; waste treatments such as incineration, composting, recycling, storage and transportation of materials are intensified. Landfill sites are seen as industrial facilities rather than merely final disposal sites. Four main issues were investigated within this new scenario, in field- and full-scale, mostly at Spillepeng site, southern Sweden. (1) Adequacy of storage piles: Regarding the increasing demand for waste storage as fuel, the adequacy of storage in piles was investigated by monitoring industrial waste (IND) fuel compacted piles. Intense biodegradation activity, which raised the temperature into the optimum range for chemical oxidation reactions, was noticed during the first weeks. After about six months of storage, self-ignition occurred in one IND pile and one refuse derived fuel (RDF) pile. Heat, O{sub 2} and CO{sub 2} distribution at different depths of the monitored IND pile suggested that natural convection plays an important role in the degradation process by supplying oxygen and releasing heat. Storage techniques that achieve a higher degree of compaction, such as baling, are preferable to storage in piles. ( 2) Discharge from landfill for special waste: Regarding changes in the composition of the waste sent to landfills and the consequences for its hydrological performance in active and capped landfills, discharge from a full-scale landfill for special/hazardous waste (predominantly fly ash from municipal solid waste (MSW) incineration) was modelled using the U.S. EPA HELP model. Hydraulic properties of the special waste were compared with those from MSW. Lower practical field capacity and higher hydraulic conductivity at

  5. Chemical kinetics and transport processes in supercritical fluid extraction of coal. Final report, August 10, 1990--December 30, 1992

    Energy Technology Data Exchange (ETDEWEB)

    McCoy, B.J.; Smith, J.M.; Wang, M.; Zhang, C.J.

    1993-02-01

    The overall objective of this project was to study the supercritical fluid extraction of hydrocarbons from coal. Beyond the practical concern of deriving products from coal, the research has provided insights into the structure, properties, and reactivities of coal. Information on engineering fundamentals of coal thermolysis and extraction, including physical and chemical processes, is presented in this final report. To accomplish the goals of the project we developed continuous-flow experiments for fixed-bed samples of coal that allow two types of analysis of the extract: continuous spectrophotometric absorbance measurements of the lumped concentration of extract, and chromatographic determinations of molecular-weight distributions as a function of time. Thermolysis of coal yields a complex mixture of many extract products whose molecular-weight distribution (MWD) varies with time for continuous-flow, semibatch experiments. The flow reactor with a differential, fixed bed of coal particles contacted by supercritical t-butanol was employed to provide dynamic MWD data by means of HPLC gel permeation chromatography of the extract. The experimental results, time-dependent MWDs of extract molecules, were interpreted by a novel mathematical model based on continuous-mixture kinetics for thermal cleavage of chemical bonds in the coal network. The parameters for the MWDs of extractable groups in the coal and the rate constants for one- and two-fragment reaction are determined from the experimental data. The significant effect of temperature on the kinetics of the extraction was explained in terms of one- and two-fragment reactions in the coal.

  6. Comparison of Sociometrically High Visibility Rejected and Low Visibility Rejected Children on Teacher, Parent, and Self-Rating Measures.

    Science.gov (United States)

    Neighbor, Jonelle C.

    The study looked at differences between groups of children identified as high visibility rejected (HVR) and low visibility rejected (LVR) on a sociometric measure with 952 fourth, fifth, and sixth grade students. Questionnaires were analyzed to determine the number of positive and negative nominations from peers received by each child. HVR…

  7. Barriers to Sustainable Food Trade: China’s Exports Food Rejected by the U.S. Food and Drug Administration 2011–2017

    Directory of Open Access Journals (Sweden)

    Xiaowei Wen

    2018-05-01

    Full Text Available Food export rejection can be a harmful barrier to sustainable international food trade. To understand China’s export food rejected by FDA (Food and Drug Administration of the United States, we analyzed 4047 cases of rejection from February 2011 to July 2017. Although the number of rejected food exported from China to the United States has been declining, and the quality has been improving, there is still space for improvement. Of the 4047 cases of rejection, the Guangdong, Fujian and Shandong provinces were the top three with the largest number of rejected food (1253 (31%, 520 (12.8%, and 508 (12.6%, respectively (being rejected mainly in New York and Los Angeles. The top four types of rejected food involved fruits and vegetables, fishery and seafood products, bakery products, grain and related processed products. More importantly, the major reasons for rejection can be attributed to problems in maintaining food safety, namely: (1 the food contained filth, decay, decomposition or other substances; (2, the food contained toxic and harmful substances (e.g., suspected melamine, chemical insecticides, or lead; and (3 the food contained agricultural and veterinary drugs. The results are of great implications for the United States to regulate the imported food from China, and for China to improve the quality and safety of export food.

  8. Acute rejection episodes after kidney transplantation

    Directory of Open Access Journals (Sweden)

    Hamida Fethi

    2009-01-01

    Full Text Available Acute rejection episodes (AREs are a major determinant of renal allograft survival. The incorporation of new immunosuppressive agents explains, at least partially, the improvement seen in the results of transplantation in recent years. The objectives of this study are to analyze the incidence and severity of AREs, their risk factors and their influence on graft and patient survival. We retrospectively studied 280 kidney transplants performed in adults at the Charles Nicolle Hospital, Tunis, between 1986 and 2004. The diagnosis of ARE was based on clinical data and response to treatment. Allograft biopsies were performed in ten cases. The treatment of AREs consisted of pulse methylprednisolone and anti-thymocyte globulin. There were 186 males (66.4% and 94 females (33.6%, and their mean age was 31 ± 8.9 years. Overall, the 280 study patients experienced a total of 113 AREs. Of them, 85 had only one ARE, 28 had two to three and none had more than three AREs. A total of 68 AREs were completely re-versible, 42 were partially reversible while three could not be reversed with treatment. The mean inci-dence of AREs was 40.4%. The incidence was > 45% between 1986 and 1997, decreased to 20.5% between 1998 and 2000 and to 9% between 2001 and 2004. Graft survival rates in patients with and without AREs were respectively 91% and 93% at three years, 82% and 90% at five years and 73% and 83% at 10 years. We found a decrease in the incidence of AREs in recent years in our study patients, and this was related to the introduction of sensitized cross-match and the newer immunosuppressive agents, particularly MMF. Additionally, AREs had a deleterious impact on late graft survival in our study population.

  9. Quantum Communication Using Coherent Rejection Sampling.

    Science.gov (United States)

    Anshu, Anurag; Devabathini, Vamsi Krishna; Jain, Rahul

    2017-09-22

    Compression of a message up to the information it carries is key to many tasks involved in classical and quantum information theory. Schumacher [B. Schumacher, Phys. Rev. A 51, 2738 (1995)PLRAAN1050-294710.1103/PhysRevA.51.2738] provided one of the first quantum compression schemes and several more general schemes have been developed ever since [M. Horodecki, J. Oppenheim, and A. Winter, Commun. Math. Phys. 269, 107 (2007); CMPHAY0010-361610.1007/s00220-006-0118-xI. Devetak and J. Yard, Phys. Rev. Lett. 100, 230501 (2008); PRLTAO0031-900710.1103/PhysRevLett.100.230501A. Abeyesinghe, I. Devetak, P. Hayden, and A. Winter, Proc. R. Soc. A 465, 2537 (2009)PRLAAZ1364-502110.1098/rspa.2009.0202]. However, the one-shot characterization of these quantum tasks is still under development, and often lacks a direct connection with analogous classical tasks. Here we show a new technique for the compression of quantum messages with the aid of entanglement. We devise a new tool that we call the convex split lemma, which is a coherent quantum analogue of the widely used rejection sampling procedure in classical communication protocols. As a consequence, we exhibit new explicit protocols with tight communication cost for quantum state merging, quantum state splitting, and quantum state redistribution (up to a certain optimization in the latter case). We also present a port-based teleportation scheme which uses a fewer number of ports in the presence of information about input.

  10. Two-stage, in silico deconvolution of the lymphocyte compartment of the peripheral whole blood transcriptome in the context of acute kidney allograft rejection.

    Science.gov (United States)

    Shannon, Casey P; Balshaw, Robert; Ng, Raymond T; Wilson-McManus, Janet E; Keown, Paul; McMaster, Robert; McManus, Bruce M; Landsberg, David; Isbel, Nicole M; Knoll, Greg; Tebbutt, Scott J

    2014-01-01

    Acute rejection is a major complication of solid organ transplantation that prevents the long-term assimilation of the allograft. Various populations of lymphocytes are principal mediators of this process, infiltrating graft tissues and driving cell-mediated cytotoxicity. Understanding the lymphocyte-specific biology associated with rejection is therefore critical. Measuring genome-wide changes in transcript abundance in peripheral whole blood cells can deliver a comprehensive view of the status of the immune system. The heterogeneous nature of the tissue significantly affects the sensitivity and interpretability of traditional analyses, however. Experimental separation of cell types is an obvious solution, but is often impractical and, more worrying, may affect expression, leading to spurious results. Statistical deconvolution of the cell type-specific signal is an attractive alternative, but existing approaches still present some challenges, particularly in a clinical research setting. Obtaining time-matched sample composition to biologically interesting, phenotypically homogeneous cell sub-populations is costly and adds significant complexity to study design. We used a two-stage, in silico deconvolution approach that first predicts sample composition to biologically meaningful and homogeneous leukocyte sub-populations, and then performs cell type-specific differential expression analysis in these same sub-populations, from peripheral whole blood expression data. We applied this approach to a peripheral whole blood expression study of kidney allograft rejection. The patterns of differential composition uncovered are consistent with previous studies carried out using flow cytometry and provide a relevant biological context when interpreting cell type-specific differential expression results. We identified cell type-specific differential expression in a variety of leukocyte sub-populations at the time of rejection. The tissue-specificity of these differentially

  11. Two-stage, in silico deconvolution of the lymphocyte compartment of the peripheral whole blood transcriptome in the context of acute kidney allograft rejection.

    Directory of Open Access Journals (Sweden)

    Casey P Shannon

    Full Text Available Acute rejection is a major complication of solid organ transplantation that prevents the long-term assimilation of the allograft. Various populations of lymphocytes are principal mediators of this process, infiltrating graft tissues and driving cell-mediated cytotoxicity. Understanding the lymphocyte-specific biology associated with rejection is therefore critical. Measuring genome-wide changes in transcript abundance in peripheral whole blood cells can deliver a comprehensive view of the status of the immune system. The heterogeneous nature of the tissue significantly affects the sensitivity and interpretability of traditional analyses, however. Experimental separation of cell types is an obvious solution, but is often impractical and, more worrying, may affect expression, leading to spurious results. Statistical deconvolution of the cell type-specific signal is an attractive alternative, but existing approaches still present some challenges, particularly in a clinical research setting. Obtaining time-matched sample composition to biologically interesting, phenotypically homogeneous cell sub-populations is costly and adds significant complexity to study design. We used a two-stage, in silico deconvolution approach that first predicts sample composition to biologically meaningful and homogeneous leukocyte sub-populations, and then performs cell type-specific differential expression analysis in these same sub-populations, from peripheral whole blood expression data. We applied this approach to a peripheral whole blood expression study of kidney allograft rejection. The patterns of differential composition uncovered are consistent with previous studies carried out using flow cytometry and provide a relevant biological context when interpreting cell type-specific differential expression results. We identified cell type-specific differential expression in a variety of leukocyte sub-populations at the time of rejection. The tissue-specificity of

  12. Detection of cardiac transplant rejection with radiolabeled lymphocytes

    International Nuclear Information System (INIS)

    Bergmann, S.R.; Lerch, R.A.; Carlson, E.M.; Saffitz, J.E.; Sobel, B.E.

    1982-01-01

    To determine whether rejections of cardiac transplants could be detected specifically and non-invasively by lymphocytes labeled with indium-111 (111In), we studied 36 allogeneic and 14 isogeneic heterotopic cardiac transplants in rats. Allogeneic grafts accumulated autologous 111In-lymphocytes, detectable scintigraphically 24 hours after i.v. injection of the labeled cells. At the time of peak histologic rejection, the allogeneic grafts accumulated 92. +/- 4.8 times more activity than the native hearts (determined by well counting). The tissue-to-blood ratio in the rejecting transplants was 3.7 +/- 2.2; total uptake by the graft was 2.9 +/- 2.1% of the injected dose. Autoradiography confirmed that graft radioactivity was associated with labeled lymphocytes. In contrast, isogeneic grafts showed no signs of rejection and did not accumulate radioactivity. Because conventionally isolated and labeled lymphocytes are often contaminated with platelets, we prepared both 111In-platelets and purified 111In-lymphocytes for use in additional experiments. Allogeneic grafts accumulated platelets and purified lymphocytes independently. Thus, deposition of immunologically active cells in the rejecting graft representing specific pathophysiologic events can be detected. The results suggest that rejection of cardiac transplants can be detected noninvasively, potentially facilitating objective early clinical detection of rejection and titration of antirejection therapy

  13. Rejection of Organic Micropollutants by Clean and Fouled Nanofiltration Membranes

    Directory of Open Access Journals (Sweden)

    Lifang Zhu

    2015-01-01

    Full Text Available The rejection of organic micropollutants, including three polycyclic aromatic hydrocarbons (PAHs and three phthalic acid esters (PAEs, by clean and fouled nanofiltration membranes was investigated in the present study. The rejection of organic micropollutants by clean NF90 membranes varied from 87.9 to more than 99.9%, while that of NF270 membranes ranged from 32.1 to 92.3%. Clear time-dependence was observed for the rejection of hydrophobic micropollutants, which was attributed to the adsorption of micropollutants on the membrane. Fouling with humic acid had a negligible influence on the rejection of organic micropollutants by NF90 membranes, while considerable effects were observed with NF270 membranes, which are significantly looser than NF90 membranes. The observed enhancement in the rejection of organic micropollutants by fouled NF270 membranes was attributed to pore blocking, which was a dominating fouling mechanism for loose NF membranes. Changes in the ionic strength (from 10 to 20 mM reduced micropollutant rejection by both fouled NF membranes, especially for the rejection of dimethyl phthalate and diethyl phthalate by NF270 membranes (from 65.8 to 25.0% for dimethyl phthalate and 75.6 to 33.3% for diethyl phthalate.

  14. Experimental high-frequency ultrasound can detect graft rejection after small bowel transplantation.

    Science.gov (United States)

    Yang, R; Liu, Q; Wu, E X; Pescovitz, M D; Collins, M H; Kopecky, K K; Grosfeld, J L

    1994-02-01

    Early diagnosis of graft rejection after small bowel transplantation (SBT) can allow prompt institution of vigorous immunosuppressive therapy, with resultant reversal of the rejection process. The current method for graft monitoring is random mucosal biopsy from a stomal site or through an endoscope. However, because early rejection often has a patchy distribution, it could be missed by random biopsy. We hypothesized that the pathological process of rejection would alter acoustic impedance of the tissue and thus change the ultrasonic patterns of the graft intestinal wall. If this hypothesis is correct, then high-frequency endoscopic ultrasound (US) could be used to monitor the entire transplanted bowel and guide the biopsy, with improved yields. This hypothesis was tested in a rat orthotopic SBT model. Sixty-two intestinal specimens (9 isografts, 12 allografts treated with cyclosporine A [CsA], 22 untreated allografts, and 19 intestines from normal rats) were collected for in vitro transluminal US imaging (30 MHz) and histopathologic study. The echo pattern of normal rat intestinal wall consisted of five echo layers that correlated spatially with the histological layers: the innermost hyperechoic layer 1, plus hypoechoic layer 2, corresponded to the mucosa; hyperechoic layer 3, the submucosa; anechoic layer 4, the muscularis propria; and hyperechoic layer 5, the serosa. The isografts and CsA-treated allografts were identical histologically and ultrasonically to normal intestine. However, the echo patterns of the untreated allografts had progressive loss of architectural stratification, with worsening rejection. The change began with patchy indistinctness and disruption of hyperechoic layers 1, 3 and 5, and progressed to total obliteration of the layers, with the intestinal wall becoming a nonstratified hypoechoic structure.(ABSTRACT TRUNCATED AT 250 WORDS)

  15. Two strategies for phosphorus removal from reject water of municipal wastewater treatment plant using alum sludge.

    Science.gov (United States)

    Yang, Y; Zhao, Y Q; Babatunde, A O; Kearney, P

    2009-01-01

    In view of the well recognized need of reject water treatment in MWWTP (municipal wastewater treatment plant), this paper outlines two strategies for P removal from reject water using alum sludge, which is produced as by-product in drinking water treatment plant when aluminium sulphate is used for flocculating raw waters. One strategy is the use of the alum sludge in liquid form for co-conditioning and dewatering with the anaerobically digested activated sludge in MWWTP. The other strategy involves the use of the dewatered alum sludge cakes in a fixed bed for P immobilization from the reject water that refers to the mixture of the supernatant of the sludge thickening process and the supernatant of the anaerobically digested sludge. Experimental trials have demonstrated that the alum sludge can efficiently reduce P level in reject water. The co-conditioning strategy could reduce P from 597-675 mg P/L to 0.14-3.20 mg P/L in the supernatant of the sewage sludge while the organic polymer dosage for the conditioning of the mixed sludges would also be significantly reduced. The second strategy of reject water filtration with alum sludge bed has shown a good performance of P reduction. The alum sludge has P-adsorption capacity of 31 mg-P/g-sludge, which was tested under filtration velocity of 1.0 m/h. The two strategies highlight the beneficial utilization of alum sludge in wastewater treatment process in MWWTP, thus converting the alum sludge as a useful material, rather than a waste for landfill.

  16. Rejection sensitivity as a vulnerability marker for depressive symptom deterioration in men.

    Directory of Open Access Journals (Sweden)

    Jannika De Rubeis

    Full Text Available Consistent across time and cultures, men and male adolescents older than 14 years of age appear underrepresented in mood disorders, and are far less likely than women to seek psychological help. The much higher rate of suicide amongst males suggests that depression in men might be underreported. One of the core human motives is to seek acceptance by others and avoid rejection. Rejection Sensitivity (RS has been conceptualized as the cognitive-affective processing disposition to anxiously expect, readily perceive, and intensely respond to cues of rejection in the behavior of others. RS has been previously linked with the onset and course of depression, but-as yet-has not been investigated longitudinally in a clinical population. We investigated the predictive role of RS to symptom deterioration 6 months after end-of- treatment in 72 male inpatients with depressive spectrum disorder. The BDI was administered at intake, end-of-treatment and 6 month follow-up. RS scores were obtained at intake. Rejection Sensitivity had additional predictive power on BDI scores at 6 months follow-up controlling for BDI scores at end-of-treatment (ΔR2 = .095. The results are discussed in terms of the importance of targeting RS during treatment, and highlight the fact that therapeutic follow-up care is paramount. Future research should investigate possible mediators of the RS-relapse-to-depression association, such as self-blame, rumination, neuroticism, pessimism, emotion dysregulation, and low self-esteem.

  17. Study on the abnormal data rejection and normal condition evaluation applied in wind turbine farm

    Science.gov (United States)

    Zhang, Ying; Qian, Zheng; Tian, Shuangshu

    2016-01-01

    The condition detection of wind turbine is always an important issue which attract more and more attentions because of the rapid development of wind farm. And the on-line data analysis is also difficult since a lot of measured data is collected. In this paper, the abnormal data rejection and normal condition evaluation of wind turbine is processed. At first, since there are large amounts of abnormal data in the normal operation of wind turbine, which is probably caused by fault, maintenance downtime, power-limited operation and failure of wind speed sensor, a novel method is proposed to reject abnormal data in order to make more accurate analysis for the wind turbine condition. The core principle of this method is to fit the wind power curves by using the scatter diagram. The data outside the area covered by wind power curves is the abnormal data. The calculation shows that the abnormal data is rejected effectively. After the rejection, the vibration signals of wind turbine bearing which is a critical component are analyzed and the relationship between the vibration characteristic value and the operating condition of wind turbine is discussed. It will provide powerful support for the accurate fault analysis of wind turbine.

  18. Noise-Coupled Image Rejection Architecture of Complex Bandpass ΔΣAD Modulator

    Science.gov (United States)

    San, Hao; Kobayashi, Haruo

    This paper proposes a new realization technique of image rejection function by noise-coupling architecture, which is used for a complex bandpass ΔΣAD modulator. The complex bandpass ΔΣAD modulator processes just input I and Q signals, not image signals, and the AD conversion can be realized with low power dissipation. It realizes an asymmetric noise-shaped spectra, which is desirable for such low-IF receiver applications. However, the performance of the complex bandpass ΔΣAD modulator suffers from the mismatch between internal analog I and Q paths. I/Q path mismatch causes an image signal, and the quantization noise of the mirror image band aliases into the desired signal band, which degrades the SQNDR (Signal to Quantization Noise and Distortion Ratio) of the modulator. In our proposed modulator architecture, an extra notch for image rejection is realized by noise-coupled topology. We just add some passive capacitors and switches to the modulator; the additional integrator circuit composed of an operational amplifier in the conventional image rejection realization is not necessary. Therefore, the performance of the complex modulator can be effectively raised without additional power dissipation. We have performed simulation with MATLAB to confirm the validity of the proposed architecture. The simulation results show that the proposed architecture can achieve the realization of image-rejection effectively, and improve the SQNDR of the complex bandpass ΔΣAD modulator.

  19. A conservative and a hybrid early rejection schemes for accelerating Monte Carlo molecular simulation

    KAUST Repository

    Kadoura, Ahmad Salim

    2014-03-17

    Molecular simulation could provide detailed description of fluid systems when compared to experimental techniques. They can also replace equations of state; however, molecular simulation usually costs considerable computational efforts. Several techniques have been developed to overcome such high computational costs. In this paper, two early rejection schemes, a conservative and a hybrid one, are introduced. In these two methods, undesired configurations generated by the Monte Carlo trials are rejected earlier than it would when using conventional algorithms. The methods are tested for structureless single-component Lennard-Jones particles in both canonical and NVT-Gibbs ensembles. The computational time reduction for both ensembles is observed at a wide range of thermodynamic conditions. Results show that computational time savings are directly proportional to the rejection rate of Monte Carlo trials. The proposed conservative scheme has shown to be successful in saving up to 40% of the computational time in the canonical ensemble and up to 30% in the NVT-Gibbs ensemble when compared to standard algorithms. In addition, it preserves the exact Markov chains produced by the Metropolis scheme. Further enhancement for NVT-Gibbs ensemble is achieved by combining this technique with the bond formation early rejection one. The hybrid method achieves more than 50% saving of the central processing unit (CPU) time.

  20. Assessment of chemical processes for the post-accident decontamination of reactor-coolant systems. Final report

    International Nuclear Information System (INIS)

    Munson, L.F.; Card, C.J.; Divine, J.R.

    1983-02-01

    Previously used chemical decontamination processes and potentially useful new decontamination processes were examined for the usefulness following a reactor accident. Both generic fuel damage accidents and the accident at TMI-2 were considered. A total of fourteen processes were evaluated. Process evaluation included data in the following categories: technical description of the process, recorded past usage, effectiveness, process limitation, safety consideration, and waste management. These data were evaluated, and cost considerations were presented along with a description of the applicability of the process to TMI-2 and development and demonstration needs. Specific recommendations regarding a primary-system decontamination development program to support TMI-2 recovery were also presented

  1. Family Planning: Between Rejection And Acceptance In Islam ...

    African Journals Online (AJOL)

    Family Planning: Between Rejection And Acceptance In Islam. ... factor for health workers and policy makers to impact positively on their communities. ... who are likely to work in such communities for effective negotiation and application of ...

  2. Perceived parental rejection mediates the effects of previous ...

    African Journals Online (AJOL)

    Behavioural problems, parental rejection scores and child abuse ... evaluated by the Child Behavior Checklist (parental version), the Memories of Parental Rearing ... However, mental illness had no moderating effect on these relationships.

  3. Reliability and construct validity for scale of rejection of Christianity.

    Science.gov (United States)

    Robbins, Mandy; Francis, Leslie J; Bradford, Amanda

    2003-02-01

    A sample of 16 male and 30 female undergraduates completed the Greer and Francis Scale of Rejection of Christianity. The data support the internal consistency reliability and construct validity of the scale for this sample.

  4. Prediction of acute cardiac rejection using radionuclide techniques

    International Nuclear Information System (INIS)

    Novitzky, D.; Bonioszczuk, J.; Cooper, D.K.C.; Isaacs, S.; Rose, A.G.; Smith, J.A.; Uys, C.J.; Barnard, C.N.; Fraser, R.

    1984-01-01

    Radionuclide scanning of the donor left ventricle using technetium-99m-labelled red cells was used to monitor acute rejection after heterotopic heart transplantation and compared with histopathological evidence of rejection obtained at examination of an endomyocardial biopsy specimen. The ejection fraction and end-diastolic, end-systolic and stroke volumes were calculated at each examination; an equation was derived from these data to predict the degree of acute rejection, using histopathological examination of endomyocardial biopsy specimens as criteria of the presence and severity of rejection. A highly significant multiple correlation between radionuclide scanning parameters and endomyocardial biopsy was found. The advantages of non-invasive radionuclide scanning over the invasive procedure of endomyocardial biopsy are discussed

  5. Behavioral and Personality Predictors of Acceptance and Rejection in University

    Directory of Open Access Journals (Sweden)

    Daniel Bartholomeu

    Full Text Available Abstract: Acceptance and rejection in the group are related to both personality characteristics and social skills and most studies focus on children instead of college students. The objective of this study was to investigate whether acceptance and rejection would be more associated with personality tendencies, specifically socialization or social skills. We collected data from 187 college students attending the Physical Education (67% and Psychology (32% courses. The instruments were the sociometric test, the Factorial Scale of Socialization and the Social Skills Inventory. A moderating effect of gender in the relationship between assertiveness and acceptance and rejection to go out on college was observed. Social skills were better predictors of acceptance and social rejection in the university group.

  6. Why don't you like me? Midfrontal theta power in response to unexpected peer rejection feedback.

    Science.gov (United States)

    van der Molen, M J W; Dekkers, L M S; Westenberg, P M; van der Veen, F M; van der Molen, M W

    2017-02-01

    Social connectedness theory posits that the brain processes social rejection as a threat to survival. Recent electrophysiological evidence suggests that midfrontal theta (4-8Hz) oscillations in the EEG provide a window on the processing of social rejection. Here we examined midfrontal theta dynamics (power and inter-trial phase synchrony) during the processing of social evaluative feedback. We employed the Social Judgment paradigm in which 56 undergraduate women (mean age=19.67 years) were asked to communicate their expectancies about being liked vs. disliked by unknown peers. Expectancies were followed by feedback indicating social acceptance vs. rejection. Results revealed a significant increase in EEG theta power to unexpected social rejection feedback. This EEG theta response could be source-localized to brain regions typically reported during activation of the saliency network (i.e., dorsal anterior cingulate cortex, insula, inferior frontal gyrus, frontal pole, and the supplementary motor area). Theta phase dynamics mimicked the behavior of the time-domain averaged feedback-related negativity (FRN) by showing stronger phase synchrony for feedback that was unexpected vs. expected. Theta phase, however, differed from the FRN by also displaying stronger phase synchrony in response to rejection vs. acceptance feedback. Together, this study highlights distinct roles for midfrontal theta power and phase synchrony in response to social evaluative feedback. Our findings contribute to the literature by showing that midfrontal theta oscillatory power is sensitive to social rejection but only when peer rejection is unexpected, and this theta response is governed by a widely distributed neural network implicated in saliency detection and conflict monitoring. Copyright © 2016 Elsevier Inc. All rights reserved.

  7. Associations between rejection sensitivity and mental health outcomes : A meta-analytic review

    NARCIS (Netherlands)

    Gao, S.; Assink, M.; Cipriani, A.; Lin, K.

    2017-01-01

    Rejection sensitivity is a personality disposition characterized by oversensitivity to social rejection. Using a three-level meta-analytic model, 75 studies were reviewed that examined associations between rejection sensitivity and five mental health outcomes: depression, anxiety, loneliness,

  8. Acute Hepatic Allograft Rejection in Pediatric Recipients: Independent Factors

    OpenAIRE

    Dehghani, S. M.; Shahramian, I.; Afshari, M.; Bahmanyar, M.; Ataollahi, M.; Sargazi, A.

    2017-01-01

    Background: Acute cellular rejection (ACR) has a reversible effect on graft and its survival. Objective: To evaluate the relation between ACR and clinical factors in recipients of liver transplant allografts. Methods: 47 consecutive liver recipients were retrospectively studied. Their data were extracted from records and analyzed. Results: 38 (81%) of the 47 recipients experienced ACR during a 24-month follow-up. The rate of rejection was associated with none of the studied factors—recipient’...

  9. EEG Asymmetry in Borderline Personality Disorder and Depression Following Rejection

    OpenAIRE

    Beeney, Joseph E.; Levy, Kenneth N.; Gatzke-Kopp, Lisa M.; Hallquist, Michael N.

    2013-01-01

    Borderline personality disorder (BPD) and major depressive disorder (MDD) share numerous features including dysphoric affect, irritability, suicidality, and a heightened sensitivity to perceived interpersonal rejection. However, these disorders are associated with divergent profiles of reactivity to rejection; individuals with MDD are more likely to respond with withdrawal and isolation, and those with BPD appear to respond with increased approach behaviors and greater hostility. Potential me...

  10. Maternal Predictors of Rejecting Parenting and Early Adolescent Antisocial Behavior

    OpenAIRE

    Trentacosta, Christopher J.; Shaw, Daniel S.

    2007-01-01

    The present study examined relations among maternal psychological resources, rejecting parenting, and early adolescent antisocial behavior in a sample of 231 low-income mothers and their sons with longitudinal assessments from age 18 months to 12 years. The maternal resources examined were age at first birth, aggressive personality, and empathy. Each of the maternal resources predicted rejecting parenting during early childhood in structural equation models that controlled for toddler difficu...

  11. COTRANSA simulation of Chinshan unit one generator load rejection test

    International Nuclear Information System (INIS)

    Wu, C.H.

    1984-01-01

    A simulation of the plant behavior during a BWR generator load rejection transient using Exxon Nuclear Company's COTRANSA code is presented in this paper. The results are compared to measurements obtained by Taiwan Power Company during a generator load rejection transient, initiated at full power condition, which was one of the Chinshan Unit 1 initial cycle startup tests. Good agreement between the COTRANSA predicted and the measured values, indicates that the COTRANSA code can simulate this transient satisfactorily

  12. Final disposal of spent nuclear fuel in Sweden. Some unresolved issues and challenges in the design and implementation of the forthcoming planning and EIA processes

    Energy Technology Data Exchange (ETDEWEB)

    Bjarnadottir, H.; Hilding-Rydevik, T. [Nordregio, Stockholm (Sweden)

    2001-06-01

    The aim of the study is to highlight some unresolved and challenging issues in the forthcoming approximately six year long Environmental Impact Assessment (EIA) and planning process of the long-term disposal of spent nuclear fuel in Sweden. Different international and Nordic experiences of the processes for final disposal as well as from other development of similar scope, where experiences assumed to be of importance for final disposal of nuclear waste, have been described. Furthermore, issues relating to 'good EIA practice' as well as certain aspects of planning theory have also been presented. The current Swedish situation for the planning and EIA process of the final disposal of spent nuclear fuel was also been summarized. These different 'knowledge areas' have been compared and measured against our perception of the expectations towards the forthcoming process, put forward by different Swedish actors in the field. The result is a presentation of a number of questions and identification issues that the authors consider need special attention in the design and conduction of the planning and EIA process. The study has been realized through a literature survey and followed by reading and analysis of the written material. The main focus of the literature search was on material describing planning processes, actor perspectives and EIA. Material and literature on the technical and scientific aspects of spent nuclear fuel disposal was however deliberately avoided. There is a wealth of international and Swedish literature concerning final disposal of spent nuclear fuel - concerning both technical issues and issues concerning for example public participation and risk perception. But material of a more systematic and comparative nature (relating to both empirical and theoretical issues, and to practical experiences) in relation to EIA processes and communicative planning for final disposal of spent nuclear fuel seems to be more sparsely represented

  13. Higher boron rejection with a new TFC forward osmosis membrane

    KAUST Repository

    Valladares Linares, Rodrigo; Li, Zhenyu; Sarp, Sarper; Park, Y. G.; Amy, Gary L.; Vrouwenvelder, Johannes S.

    2014-01-01

    Due to the stringent limits for boron in drinking and irrigation water, water treatment facilities have to incur additional treatment to remove boron down to a safe concentration. Forward osmosis (FO) is a membrane technology that may reduce the energy required to remove boron present in seawater. In direct FO desalination hybrid systems, fresh water is recovered from seawater using a recoverable draw solution, FO membranes are expected to show high boron rejection. This study focuses on determining the boron rejection capabilities of a new generation thin-film composite (TFC) FO membrane compared to a first generation cellulose triacetate (CTA) FO membrane. The effects of water permeate flux, membrane structure, draw solute charge, and reverse solute flux on boron rejection were determined. For TFC and CTA FO membranes, experiments showed that when similar operating conditions are applied (e.g. membrane type and draw solute type) boron rejection decreases with increase in permeate flux. Reverse draw solute flux and membrane fouling have no significant impact on boron rejection. Compared to the first generation CTA FO membrane operated at the same conditions, the TFC FO membrane showed a 40% higher boron rejection capability and a 20% higher water flux. This demonstrates the potential for boron removal for new generation TFC FO membranes. © 2014 © 2014 Balaban Desalination Publications. All rights reserved.

  14. Higher boron rejection with a new TFC forward osmosis membrane

    KAUST Repository

    Valladares Linares, Rodrigo

    2014-07-17

    Due to the stringent limits for boron in drinking and irrigation water, water treatment facilities have to incur additional treatment to remove boron down to a safe concentration. Forward osmosis (FO) is a membrane technology that may reduce the energy required to remove boron present in seawater. In direct FO desalination hybrid systems, fresh water is recovered from seawater using a recoverable draw solution, FO membranes are expected to show high boron rejection. This study focuses on determining the boron rejection capabilities of a new generation thin-film composite (TFC) FO membrane compared to a first generation cellulose triacetate (CTA) FO membrane. The effects of water permeate flux, membrane structure, draw solute charge, and reverse solute flux on boron rejection were determined. For TFC and CTA FO membranes, experiments showed that when similar operating conditions are applied (e.g. membrane type and draw solute type) boron rejection decreases with increase in permeate flux. Reverse draw solute flux and membrane fouling have no significant impact on boron rejection. Compared to the first generation CTA FO membrane operated at the same conditions, the TFC FO membrane showed a 40% higher boron rejection capability and a 20% higher water flux. This demonstrates the potential for boron removal for new generation TFC FO membranes. © 2014 © 2014 Balaban Desalination Publications. All rights reserved.

  15. Rejection or selection: influence of framing in investment decisions.

    Science.gov (United States)

    Cheng, Pi-Yueh; Chiou, Wen-Bin

    2010-02-01

    According to prospect theory, reflection effects result in preferences for risk-averse choices in gain situations and risk-seeking choices in loss situations. However, relevant literature in regard to decision making has suggested that positive information receives more weight in a selection task, whereas negative information receives more weight in a rejection task. The present study examined whether the nature of a decision task (selection vs rejection) would moderate the reflection effects. Undergraduates (47 men, 49 women; M age = 20.5 yr., SD = 1.1), selected according to specific screening criteria, participated in an experimental study. Typical reflection effects were observed in both selection and rejection task conditions. More importantly, negative information (i.e., the information about probable loss in risky choice of gain situations and the information about certain loss in cautious choice of loss situations) provided in the context of a rejection task received more weight and resulted in more frequent endorsements of the cautious choice in gain situations and of the risky choice in loss situations. Hence, the findings suggest that a decision context characterized by rejection may expand the reflection effects and thereby provide important information about situations in which investment decisions occur in a context characterized by rejection.

  16. Mediation and Due Process Procedures in Special Education: An Analysis of State Policies. Final Report. Project FORUM.

    Science.gov (United States)

    Ahearn, Eileen M.

    This survey of 50 states and 3 of 10 non-state U.S. jurisdictions concerning state due process procedures focuses mainly on the use of mediation as a form of dispute resolution that offers an alternative to due process hearings in special education. A background section discusses the definition of mediation and the mediation process. Survey…

  17. Limbic justice--amygdala involvement in immediate rejection in the Ultimatum Game.

    Directory of Open Access Journals (Sweden)

    Katarina Gospic

    2011-05-01

    Full Text Available Imaging studies have revealed a putative neural account of emotional bias in decision making. However, it has been difficult in previous studies to identify the causal role of the different sub-regions involved in decision making. The Ultimatum Game (UG is a game to study the punishment of norm-violating behavior. In a previous influential paper on UG it was suggested that frontal insular cortex has a pivotal role in the rejection response. This view has not been reconciled with a vast literature that attributes a crucial role in emotional decision making to a subcortical structure (i.e., amygdala. In this study we propose an anatomy-informed model that may join these views. We also present a design that detects the functional anatomical response to unfair proposals in a subcortical network that mediates rapid reactive responses. We used a functional MRI paradigm to study the early components of decision making and challenged our paradigm with the introduction of a pharmacological intervention to perturb the elicited behavioral and neural response. Benzodiazepine treatment decreased the rejection rate (from 37.6% to 19.0% concomitantly with a diminished amygdala response to unfair proposals, and this in spite of an unchanged feeling of unfairness and unchanged insular response. In the control group, rejection was directly linked to an increase in amygdala activity. These results allow a functional anatomical detection of the early neural components of rejection associated with the initial reactive emotional response. Thus, the act of immediate rejection seems to be mediated by the limbic system and is not solely driven by cortical processes, as previously suggested. Our results also prompt an ethical discussion as we demonstrated that a commonly used drug influences core functions in the human brain that underlie individual autonomy and economic decision making.

  18. Community structure analysis of rejection sensitive personality profiles: A common neural response to social evaluative threat?

    Science.gov (United States)

    Kortink, Elise D; Weeda, Wouter D; Crowley, Michael J; Gunther Moor, Bregtje; van der Molen, Melle J W

    2018-06-01

    Monitoring social threat is essential for maintaining healthy social relationships, and recent studies suggest a neural alarm system that governs our response to social rejection. Frontal-midline theta (4-8 Hz) oscillatory power might act as a neural correlate of this system by being sensitive to unexpected social rejection. Here, we examined whether frontal-midline theta is modulated by individual differences in personality constructs sensitive to social disconnection. In addition, we examined the sensitivity of feedback-related brain potentials (i.e., the feedback-related negativity and P3) to social feedback. Sixty-five undergraduate female participants (mean age = 19.69 years) participated in the Social Judgment Paradigm, a fictitious peer-evaluation task in which participants provided expectancies about being liked/disliked by peer strangers. Thereafter, they received feedback signaling social acceptance/rejection. A community structure analysis was employed to delineate personality profiles in our data. Results provided evidence of two subgroups: one group scored high on attachment-related anxiety and fear of negative evaluation, whereas the other group scored high on attachment-related avoidance and low on fear of negative evaluation. In both groups, unexpected rejection feedback yielded a significant increase in theta power. The feedback-related negativity was sensitive to unexpected feedback, regardless of valence, and was largest for unexpected rejection feedback. The feedback-related P3 was significantly enhanced in response to expected social acceptance feedback. Together, these findings confirm the sensitivity of frontal midline theta oscillations to the processing of social threat, and suggest that this alleged neural alarm system behaves similarly in individuals that differ in personality constructs relevant to social evaluation.

  19. Reexamination of the role of Lyt-2-positive T cells in murine skin graft rejection

    International Nuclear Information System (INIS)

    LeFrancois, L.; Bevan, M.J.

    1984-01-01

    The authors have investigated which T cell subclass defined by cytolysis with monoclonal anti-Lyt-1.2 and anti-Lyt-2.2 antibodies is required to adoptively transfer the ability to reject skin grafts. B6.Thy-1.1 spleen cells immune to graft antigens were fractionated with antibody plus C' and transferred to adult thymectomized, irradiated, bone marrow-reconstituted (ATXBM) B6.Thy-1.2 hosts that were simultaneously grafted with BALB.B skin. The authors found that when the ATXBM hosts were used 6 wk after irradiation and marrow reconstitution, both Lyt-1-depleted and Lyt-2-depleted immune spleen cells could transfer the ability to promptly reject skin grafts. However, such ATXBM recipients of Lyt-2-depleted cells that had rejected skin grafts were found to contain graft-specific CTL that were largely of host (B6.Thy-1.2) origin. When ATXBM hosts were used for the experiment 1 wk after irradiation and marrow reconstitution, no host-derived graft-specific CTL could be detected. However, graft rejection occurred in recipients of anti-Lyt-1- or anti-Lyt-2 plus C'-treated immune cells and specific CTL were generated from spleen cells of both groups. Thus, in the absence of a host-derived response, adoptively transferred immune Lyt-2+ cells, either resistant to, or that escaped from, antibody plus C' treatment, are able to expand in response to the antigenic stimulus provided by the graft. A more complete elimination of specific T cell subclasses is therefore needed to assess the relative contribution of a particular subset to the graft rejection process

  20. Mating behaviour of Pseudodiaptomus annandalei (Copepoda Calanoida) with emphasis on rejection rate

    Science.gov (United States)

    Dur, G.; Souissi, S.; Schmitt, F. G.; Hwang, J. S.; Cheng, S. H.

    2009-04-01

    swimming trajectories are more convoluted, indicating that males explore larger volume of fluid to increase the probability to encounter a female. The mate finding behaviour appears to depend not only on chemical signal but also on hydromechanical signals. Some males exhibited shifts of direction when females were passing by. When male intercepted a chemical trail left by a female, they initiate tracking behaviour racing up the trail with increasing speed. Males pursued pheromone trails up to 24 sec old and 10 mm long. Most studies of mating behaviour have focused on detection and sometimes pursuit, but few have addressed the other components of successful mating, namely, capture and copulation. Moreover, mate choice issue has largely been ignored in regards to pelagic copepods. Consequently very few are known about the plasticity of rejection rates as a function of mate encounter rates. The second aim of this experiment is to describe the process used by female to select their mate and to fill the gap in the quantification of mating success. Once caught by a male, P. annandalei's females entered in intensive dance which sometimes lead to shake off the males suggesting a female mate choice. The three-dimensional trajectories described by the couple during this event were characterized by fast loops and intense jumps. Individual's access to mates may be affected by operational sex ratios, causing strong variation in mating success. We finally manipulated adult sex ratios of the brackish copepod P. annandalei, to examine the influence of population sex ratio on mating success of P. annandalei in a final set of experiment concluding the investigation. It should be notice that, to our knowledge, it the first quantification ever done before. The plasticity of rejection rate was therefore investigated as a function of sex-ratio and mate encounter rate. The encounter rate reached maximum value for balanced proportion of male and female and decreased as the sex ratio unbalanced

  1. Adaptive sidelobe control for clutter rejection of atmospheric radars

    Directory of Open Access Journals (Sweden)

    K. Kamio

    2004-11-01

    Full Text Available Clutter rejection is among the most important issues in radar signal processing, for which the adaptive antenna technique can be a powerful means. Compared to other applications of the adaptive antenna, however, atmospheric radars require strict conditions, which have prevented application of this technique; the main antenna beam pattern should not be altered since the target region is defined by its shape. In particular, the loss of the antenna gain should be kept to no more than about 0.5dB, in order to maintain the high sensitivity of the system. Also, clutter from surrounding mountains is often stronger than the desired weak scattering from atmospheric turbulence. We introduce a new algorithm which satisfies the above conditions, and confirms its capability by applying it to actual data taken by the MU radar. This paper presents the first report that demonstrates the effectiveness of the adaptive antenna technique in atmospheric radar applications. Despite the fact that no information is given on the spectral features of the desired and undesired signals, only the clutter echoes from surrounding mountains were effectively cancelled without affecting the desired echoes from atmospheric turbulence.

  2. New clutter-rejection algorithm for Doppler ultrasound

    Science.gov (United States)

    Cloutier, Guy; Chen, Danmin; Durand, Louis-Gilles

    2002-04-01

    Several strategies, known as clutter or wall Doppler filtering, were proposed to remove the strong echoes produced by stationary or slow moving tissue structures from the Doppler blood flow signal. In this study, the matching pursuit (MP) method is proposed to remove clutter components. The MP method decomposes the Doppler signal into wavelet atoms that are selected in a decreasing energy order. Thus, the high-energy clutter components are extracted first. In the present study, the pulsatile Doppler signal s(n) was simulated by a sum of random-phase sinusoids. Two types of high-amplitude clutter signals were then superimposed on s(n): a time-varying low frequency component (type 1), covering systole and early diastole, and short transient clutter signals (type 2), distributed within the whole cardiac cycle. The Doppler signals were modeled with the MP method and the most dominant atoms were subtracted until the signal-to-clutter (S/C) ratio reached a maximum. For the type 1 clutter signal, the improvement in the S/C ratio was 19.0 +/- 0.6 dB, and 72.0 +/- 4.5 atoms were required to reach this performance. For the transient type 2 clutter signal, exactly 10 atoms were required and the maximum improvement in S/C ratio was 5.5 +/- 0.5 dB. These results suggest the possibility of using this signal processing approach to implement clutter rejection filters on ultrasound commercial instruments.

  3. Sexual orientation, handedness, sex ratio and fetomaternal tolerance-rejection

    Directory of Open Access Journals (Sweden)

    Carlos Y Valenzuela

    2010-01-01

    Full Text Available Fraternal birth order (FBO appears as a prenatal cause of 15% of homosexual males (gays through mnemonic maternal anti-male factors. Non-right-handed men seem to be protected from homosexuality. Four hypotheses are proposed: (1 androgenic factors of non-right-handedness neutralize anti-male factors; (2 non-right-handedness and homosexuality are lethal or produce mental impairment; (3 non-right-handed male embryos are insensitive to anti-male factors; (4 mothers of non-right-handed fetuses do not produce anti-male factors. Studies of the sex ratio (SR of older and younger siblings show: (1 a significant heterogeneity in the SR of siblings of right or non-right handed heterosexual men and women; (2 lesbians are born among siblings with high SR; (3 siblings of right-handed gays show a higher SR than non-right-handed gays that present a low SR. Based on our discovery of maternal tolerance-rejection processes, associated with genetic systems (ABO, Rh, where zygotes or embryos different from their mother induce better pregnancy and maternal tolerance than do those that share antigens with their mothers, I propose a new explanation for sexual relationships, sexual orientation, handedness and sibling SR. Lesbian embryos could induce tolerance from mothers with anti-female factors. Non-right-handedness could induce maternal tolerance, or change the maternal compatibility of "gay" embryos. Alternatively, gay embryos could be poor inducers of maternal tolerance towards male traits.

  4. Sexual orientation, handedness, sex ratio and fetomaternal tolerance-rejection.

    Science.gov (United States)

    Valenzuela, Carlos Y

    2010-01-01

    Fraternal birth order (FBO) appears as a prenatal cause of 15% of homosexual males (gays) through mnemonic maternal anti-male factors. Non-right-handed men seem to be protected from homosexuality. Four hypotheses are proposed: (1) androgenic factors of non-right-handedness neutralize anti-male factors; (2) non-right-handedness and homosexuality are lethal or produce mental impairment; (3) non-right-handed male embryos are insensitive to anti-male factors; (4) mothers of non-right-handed fetuses do not produce anti-male factors. Studies of the sex ratio (SR) of older and younger siblings show: (1) a significant heterogeneity in the SR of siblings of right or non-right handed heterosexual men and women; (2) lesbians are born among siblings with high SR; (3) siblings of right-handed gays show a higher SR than non-right-handed gays that present a low SR. Based on our discovery of maternal tolerance-rejection processes, associated with genetic systems (ABO, Rh), where zygotes or embryos different from their mother induce better pregnancy and maternal tolerance than do those that share antigens with their mothers, I propose a new explanation for sexual relationships, sexual orientation, handedness and sibling SR. Lesbian embryos could induce tolerance from mothers with anti-female factors. Non-right-handedness could induce maternal tolerance, or change the maternal compatibility of "gay" embryos. Alternatively, gay embryos could be poor inducers of maternal tolerance towards male traits.

  5. Accept or Reject? Predicting Ideation Outcomes through Enterprise Social Media

    Directory of Open Access Journals (Sweden)

    Rozaidi Nik Ahmad

    2017-01-01

    Full Text Available Implementing social media in the workplace may make it easier for employees to participate in knowledge sharing activities such as Q&A and ideation. However, vetting the quality of answers and ideas becomes more complex when anyone in the company can contribute. Research on the use of social media for Q&A has shown that certain characteristics and reputation algorithms can help determine the best answers. Less is known about the ideation process and the way it plays out in social media. This paper explores the use of enterprise social media (ESM for ideation by employees in a large Russian organization distributed across nine time zones. In particular, we explore which characteristics of both ideas and their contributors predict whether ideas get accepted or rejected. Our analysis is based on logistic regression analysis of a sample of 488 ideas contributed in an ESM tool used in the organization as well as a content analysis of the types of ideas generated. Our results suggest that rather than being truly democratic and decentralized, ideation in ESM is driven by those in (or proximate to positions of organizational power.

  6. Special feature of the facilities for final disposal of radioactive waste and its potential impact on the licensing process

    International Nuclear Information System (INIS)

    Lee Gonzales, Horacio M.; Medici, Marcela A.; Alvarez, Daniela E.; Biaggio, Alfredo L.

    2009-01-01

    During the lifetime of a radioactive waste disposal facility it is possible to identify five stages: design, construction, operation, closure and post-closure. While the design, and pre-operation stages are, to some extent, similar to other kind of nuclear or radioactive facilities; construction, operation, closure and post-closure have quite special meanings in the case of radioactive waste disposal systems. For instance, the 'closure' stage of a final disposal facility seems to be equivalent to the commissioning stage of a conventional nuclear or radioactive facility. This paper describes the unique characteristics of these stages of final disposal systems, that lead to concluded that their licensing procedure can not be assimilated to the standard licensing procedures in use for other nuclear or radioactive facilities, making it necessary to develop a tailored license system. (author)

  7. Light from electron avalanches and background rejection in X-ray astronomy

    International Nuclear Information System (INIS)

    Siegmund, O.H.W.; Sanford, P.W.; Mason, I.M.; Culhane, J.L.; Cockshott, R.

    1980-01-01

    A modified version of the parallel plate imaging proportional counter, developed to register images of cosmic x-ray sources in the focal planes of x-ray telescopes, has been constructed to investigate the application of risetime discrimination to the scintillation pulses caused by the electron avalanche process. It is shown that efficient background event rejection (> 90%) is achieved and the application of this system for x-ray astronomy is discussed. (U.K.)

  8. Evaluation of load rejection to house load test at 50% power for UCN 3

    International Nuclear Information System (INIS)

    Lee, Chang Gyun; Sohn, Suk Whun; Sohn, Jong Joo; Seo, Jong Tae; Lee, Sang Keun; Kim, Yong Sung; Nam, Kyu Won; Jung, Yang Mook; Chae, Kyeong Sik; Koh, Bum Jae; Oh, Chul Sung; Park, Hee Chool

    1998-01-01

    The Load Rejection to House Load test at 50% power was successfully performed during the UCN 3 PAT period. In this test, all plant control systems automatically controlled the plant from 50% power to house load operation mode. The KISPAC code, which was used in the performance analysis during the design process of UCN 3 and 4, predictions of the test agreed with the measured data demonstrating the validity of the code as well as completeness of the plant design

  9. SR 2603. Support of the BMU in the process of decommissioning of the explorative mine Asse II. Final report for the 31.12.2008

    International Nuclear Information System (INIS)

    Kallenbach-Herbert, Beate; Ustohalova, Veronika

    2009-01-01

    The final report on the BMU support in the process of decommissioning of Asse II includes the following topics: Overview on the involved boards. Actual development in the process: inventory, contaminated brines, shut-down concept and structural safety, exchange of the operating company, appointment of an information center and financial equalization for the region. Work of the support group Asse II and the support group option's comparison. Questioning of the support group. Evaluation of the participation process with respect to the 31.12.2008.

  10. 111-Indium-labelled platelets for diagnosis of acute kidney transplant rejection and monitoring of prostacyclin anti-rejection treatment

    International Nuclear Information System (INIS)

    Leithner, C.; Pohanka, E.; Schwarz, M.; Sinzinger, H.; Syre, G.

    1984-01-01

    33 patients were examined daily under a gamma camera after weekly injections of 111-In-labelled autologous platelets over a period of at least 4 weeks after transplantation. A group of 33 patients with long-term stable and well-functioning grafts served as controls. By means of a computerized recording technique, platelet trapping in the graft was measured and expressed as platelet-uptake index (PUI). The method worked well for the early diagnosis of acute rejection signified by an increase in PUI, accompanied by a shortening of platelet half life (t/2). 6 patients suffering from acute rejection received infusions of prostacyclin in addition to conventional high-dose methylprednisolone therapy. In 4 cases the PUI decreased again and an improvement in graft function was observed. Prostacyclin infusion treatment was applied also in 12 patients with histologically-proven chronic transplant rejection. Decreased platelet consumption by the graft and a temporary improvement in transplant function were achieved. We suggest that prostacyclin could enrich the possibilities of anti-rejection treatment by providing a tool for the suppression of platelet trapping in the graft. The platelet scan served as a useful method for the early detection of acute rejection, as well as the monitoring of prostacyclin anti-rejection treatment. (Autor)

  11. Final Rule to Reduce Toxic Air Emissions from Asphalt Processing and Asphalt Roofing Manufacturing Facilities Fact Sheet

    Science.gov (United States)

    This page contains a February 2003 fact sheet with information regarding the National Emissions Standards for Hazardous Air Pollutants (NESHAP) for Asphalt Processing and Asphalt Roofing Manufacturing.

  12. Rejecting the equilibrium-point hypothesis.

    Science.gov (United States)

    Gottlieb, G L

    1998-01-01

    The lambda version of the equilibrium-point (EP) hypothesis as developed by Feldman and colleagues has been widely used and cited with insufficient critical understanding. This article offers a small antidote to that lack. First, the hypothesis implicitly, unrealistically assumes identical transformations of lambda into muscle tension for antagonist muscles. Without that assumption, its definitions of command variables R, C, and lambda are incompatible and an EP is not defined exclusively by R nor is it unaffected by C. Second, the model assumes unrealistic and unphysiological parameters for the damping properties of the muscles and reflexes. Finally, the theory lacks rules for two of its three command variables. A theory of movement should offer insight into why we make movements the way we do and why we activate muscles in particular patterns. The EP hypothesis offers no unique ideas that are helpful in addressing either of these questions.

  13. Delayed allogeneic skin graft rejection in CD26-deficient mice.

    Science.gov (United States)

    Zhao, Xiangli; Zhang, Kai; Daniel, Peter; Wisbrun, Natali; Fuchs, Hendrik; Fan, Hua

    2018-03-23

    Organ transplantation is an effective therapeutic tool for treating many terminal diseases. However, one of the biggest challenges of transplantation is determining how to achieve the long-term survival of the allogeneic or xenogeneic transplant by, for example, preventing transplant rejection. In the current study, CD26 gene-knockout mice were used to investigate the potential role of CD26/dipeptidyl peptidase-4 (DPPIV) in allogeneic skin graft rejection by tail-skin transplantation. Compared with wild-type (CD26 +/+ ) counterparts, CD26 -/- mice showed reduced necrosis of grafts and delayed graft rejection after skin transplantation. Concentrations of serum IgG, including its subclasses IgG1 and IgG2a, were significantly reduced in CD26 -/- mice during graft rejection. Moreover, after allogeneic skin transplantation, the secretion levels of the cytokines IFN-γ, IL-2, IL-6, IL-4, and IL-13 were significantly reduced, whereas the level of the cytokine IL-10 was increased in the serum of CD26 -/- mice compared with that in the serum of CD26 +/+ mice. Additionally, the concentration of IL-17 in serum and the percentage of cells secreting IL-17 in mouse peripheral blood lymphocytes (MPBLs) were both significantly lower, while the percentage of regulatory T cells (Tregs) was significantly higher in MPBLs of CD26 -/- mice than in those of CD26 +/+ mice. Furthermore, a lower percentage of CD8 + T cells in MPBLs and fewer infiltrated macrophages and T cells in graft tissues of CD26 -/- mice were detected during graft rejection. These results indicate that CD26 is involved in allogeneic skin graft rejection and provides another hint that CD26 deficiency leads to less rejection due to lower activation and proliferation of host immune cells.

  14. Review: The transcripts associated with organ allograft rejection.

    Science.gov (United States)

    Halloran, Philip F; Venner, Jeffery M; Madill-Thomsen, Katelynn S; Einecke, Gunilla; Parkes, Michael D; Hidalgo, Luis G; Famulski, Konrad S

    2018-04-01

    The molecular mechanisms operating in human organ transplant rejection are best inferred from the mRNAs expressed in biopsies because the corresponding proteins often have low expression and short half-lives, while small non-coding RNAs lack specificity. Associations should be characterized in a population that rigorously identifies T cell-mediated (TCMR) and antibody-mediated rejection (ABMR). This is best achieved in kidney transplant biopsies, but the results are generalizable to heart, lung, or liver transplants. Associations can be universal (all rejection), TCMR-selective, or ABMR-selective, with universal being strongest and ABMR-selective weakest. Top universal transcripts are IFNG-inducible (eg, CXCL11 IDO1, WARS) or shared by effector T cells (ETCs) and NK cells (eg, KLRD1, CCL4). TCMR-selective transcripts are expressed in activated ETCs (eg, CTLA4, IFNG), activated (eg, ADAMDEC1), or IFNG-induced macrophages (eg, ANKRD22). ABMR-selective transcripts are expressed in NK cells (eg, FGFBP2, GNLY) and endothelial cells (eg, ROBO4, DARC). Transcript associations are highly reproducible between biopsy sets when the same rejection definitions, case mix, algorithm, and technology are applied, but exact ranks will vary. Previously published rejection-associated transcripts resemble universal and TCMR-selective transcripts due to incomplete representation of ABMR. Rejection-associated transcripts are never completely rejection-specific because they are shared with the stereotyped response-to-injury and innate immunity. © 2017 The American Society of Transplantation and the American Society of Transplant Surgeons.

  15. Interrelation of technologies for RW preparation and sites for final isolation of the wastes from pyrochemical processing of SNF

    Energy Technology Data Exchange (ETDEWEB)

    Gupalo, V.S.; Chistyakov, V.N. [JSC - Design-Prospecting and Scientific-Research Institute of Industrial Technology -, Kashirskoye Highway, 33, Moscow 115409 (Russian Federation); Kormilitsyn, M.V.; Kormilitsyna, L.A. [JSC - State Scientific Center - Research Institute of Atomic Reactors -, Ulyanovsk region, Dimitrovgrad - 10, 433510 (Russian Federation)

    2013-07-01

    For the justification of engineering solutions and practical testing of the radiochemical component of the perspective nuclear power complex with on-site variant of nuclear fuel cycle (NFC), it is planned to establish a multi-functional research-development complex (MFCRC) for radiochemical processing of spent nuclear fuels (SNF) from fast reactors. MFCRC is being established at the NIIAR site, it comprises technological process lines, where innovation pyro-electrochemical and hydrometallurgical technologies are realized, with an option for closing the inter-chain material flows for testing the combined radiochemically converted materials. The technological flowchart for processing at the MFCRC is subdivided into 3 segments: -) complex of the lead operations for dismantling the fuel elements (FE) and fuel assemblies (FA), -) pyrochemical extraction flowchart for processing SNF, and -) hydrometallurgical flowchart for processing SNF. The engineered solutions for the management and disposition of the radioactive wastes from MFCRC are reviewed.

  16. Evaluation of the freeze-thaw/evaporation process for the treatment of produced waters. Final report, August 1992--August 1996

    Energy Technology Data Exchange (ETDEWEB)

    Boysen, J.E.; Walker, K.L.; Mefford, J.L.; Kirsch, J.R. [Resource Technology Corp., Laramie, WY (United States); Harju, J.A. [North Dakota Univ., Grand Forks, ND (United States). Energy and Environmental Research Center

    1996-06-01

    The use of freeze-crystallization is becoming increasingly acknowledged as a low-cost, energy-efficient method for purifying contaminated water. The natural freezing process can be coupled with natural evaporative processes to treat oil and gas produced waters year round in regions where subfreezing temperatures seasonally occur. The climates typical of Colorado`s San Juan Basin and eastern slope, as well as the oil and gas producing regions of Wyoming, are well suited for application of these processes in combination. Specifically, the objectives of this research are related to the development of a commercially-economic FTE (freeze-thaw/evaporation) process for the treatment and purification of water produced in conjunction with oil and natural gas. The research required for development of this process consists of three tasks: (1) a literature survey and process modeling and economic analysis; (2) laboratory-scale process evaluation; and (3) field demonstration of the process. Results of research conducted for the completion of these three tasks indicate that produced water treatment and disposal costs for commercial application of the process, would be in the range of $0.20 to $0.30/bbl in the Rocky Mountain region. FTE field demonstration results from northwestern New Mexico during the winter of 1995--96 indicate significant and simultaneous removal of salts, metals, and organics from produced water. Despite the unusually warm winter, process yields demonstrate disposal volume reductions on the order of 80% and confirm the potential for economic production of water suitable for various beneficial uses. The total dissolved solids concentrations of the FTE demonstration streams were 11,600 mg/L (feed), 56,900 mg/L (brine), and 940 mg/L (ice melt).

  17. Final Air Toxics Standards for Clay Ceramics Manufacturing, Glass Manufacturing, and Secondary Nonferrous Metals Processing Area Sources Fact Sheet

    Science.gov (United States)

    This page contains a December 2007 fact sheet with information regarding the National Emissions Standards for Hazardous Air Pollutants (NESHAP) for Clay Ceramics Manufacturing, Glass Manufacturing, and Secondary Nonferrous Metals Processing Area Sources

  18. Evaluation, engineering and development of advanced cyclone processes. Final separating media evaluation and test report (FSMER). Appendices

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-05-01

    This report consists of appendices pertaining to the separating media evaluation (calcium nitrate solution) and testing for an advanced cyclone process. Appendices include: materials safety data, aqueous medium regeneration, pH control strategy, and other notes and data.

  19. Final Report on the Audit of the Administration of the Contract Closeout Process at the Defense Contract Management Region, Dallas

    National Research Council Canada - National Science Library

    1990-01-01

    .... The audit was made from January to October 1989. The objectives of the audit were to determine the timeliness of the contract closeout process, the validity of unliquidated obligations on contracts awaiting closeout, and the timeliness...

  20. Age-related changes in ERP components of semantic and syntactic processing in a verb final language

    Directory of Open Access Journals (Sweden)

    Jee Eun Sung

    2014-04-01

    Both syntactic and semantic violations elicited negativity effects at 300-500ms time window, and the negativity effects were slightly attenuated in the elderly group. The results suggested that Korean speakers may process a syntactic component of a case marker under the semantic frame integration, eliciting the negativity effects associated with semantic violations. Elderly adults showed attenuated effects compared to the young group, indicating age-related changes emerged during real-time sentence processing.

  1. EEG asymmetry in borderline personality disorder and depression following rejection.

    Science.gov (United States)

    Beeney, Joseph E; Levy, Kenneth N; Gatzke-Kopp, Lisa M; Hallquist, Michael N

    2014-04-01

    Borderline personality disorder (BPD) and major depressive disorder (MDD) share numerous features, including dysphoric affect, irritability, suicidality, and a heightened sensitivity to perceived interpersonal rejection. However, these disorders are associated with divergent profiles of reactivity to rejection: Individuals with MDD are more likely to respond with withdrawal and isolation, and those with BPD appear to respond with increased approach behaviors and greater hostility. Potential mechanisms underlying these divergent patterns of response have not been elaborated. The goal of the present study was to assess whether prefrontal cortical asymmetry is associated with these behavioral profiles. EEG alpha activity was recorded at baseline and after individuals with BPD, MDD and healthy controls (HCs) participated in a rejection task. Although no differences were found at baseline, results demonstrated that following rejection, individuals with BPD showed greater left cortical activation, consistent with approach motivation, whereas those with MDD showed greater right cortical activation, consistent with withdrawal motivation. HCs evidenced a more balanced cortical profile, as hypothesized. Although BPD and MDD are highly comorbid, are easily confused, and are phenomenologically similar in a number of ways, individuals with these two disorders respond in very different ways to perceived rejection. PsycINFO Database Record (c) 2014 APA, all rights reserved

  2. Phenomenology’s Rejects: Religion after Derrida’s Denegations

    Directory of Open Access Journals (Sweden)

    Alvis Jason W.

    2017-10-01

    Full Text Available Religion, as well as any individuals’ volitionally chosen ‟worldview,” generally get conceived solely in affirmative terms of value. ‟Religion” has been conceptualized almost solely on the terms of axiology: as the experience of ‟the greatest” holiness (Otto, the purely valuable sacred (Eliade; the most ‟ultimate concern” (Tillich; the symbols accepted to order life (Geertz, or the binding of oneself to deep value (Müller. Yet there are limitations of such axiomatic thinking, limitations that can be exemplified through an interpretation of Derrida’s ‟globolatinization,” which he described as a system of thought that promotes a universalism of pseudo or petit-valuations, and punishes those resistant and inflexible to them in the name of toleration. This essay investigates what happens when this ‟axiomatic” register (i.e. a reduction to a set of values gets displaced in order to conceptualize religion also in terms of the nonvaluable or ‟rejected.” Rejection entails the paradox that what is rejected often speaks to a deeper reality of what in fact is desired. Thus, what we reject usually says infinitely more about us than what we claim to value and affirm. This essay interprets Derrida’s essay ‟How to Avoid Speaking: Denials” alongside his ‟Faith and Knowledge” in order to offer a Derridean conception of religion on the terms of a rejection that amounts to a double-affirmation or de-negation.

  3. Engineering and economic analysis for the utilization of geothermal fluids in a cane sugar processing plant. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Humme, J.T.; Tanaka, M.T.; Yokota, M.H.; Furumoto, A.S.

    1979-07-01

    The purpose of this study was to determine the feasibility of geothermal resource utilization at the Puna Sugar Company cane sugar processing plant, located in Keaau, Hawaii. A proposed well site area was selected based on data from surface exploratory surveys. The liquid dominated well flow enters a binary thermal arrangement, which results in an acceptable quality steam for process use. Hydrogen sulfide in the well gases is incinerated, leaving sulfur dioxide in the waste gases. The sulfur dioxide in turn is recovered and used in the cane juice processing at the sugar factory. The clean geothermal steam from the binary system can be used directly for process requirements. It replaces steam generated by the firing of the waste fibrous product from cane sugar processing. The waste product, called bagasse, has a number of alternative uses, but an evaluation clearly indicated it should continue to be employed for steam generation. This steam, no longer required for process demands, can be directed to increased electric power generation. Revenues gained by the sale of this power to the utility, in addition to other savings developed through the utilization of geothermal energy, can offset the costs associated with hydrothermal utilization.

  4. Pyrolysis of tyres. Influence of the final temperature of the process on emissions and the calorific value of the products recovered

    International Nuclear Information System (INIS)

    Diez, C.; Martinez, O.; Calvo, L.F.; Cara, J.; Moran, A.

    2004-01-01

    A study was made of the pyrolysis of tyre particles, with the aim of determining the possibilities of using the products resulting from the process as fuel. Three final temperatures were used, determined from thermogravimetric data. The design of the experiment was a horizontal oven containing a reactor into which particles of the original tyre were placed. After the process, a solid fraction (char) remained in the reactor, while the gases generated went through a set of scrubbers where most of the condensable fraction (oils) was retained. Finally, once free of this fraction, the gases were collected in glass ampoules. Solid and liquids fractions were subjected to thermogravimetric analyses in order to study their combustibility. The gas fraction was analysed by means of gas chromatography to establish the content of CO, CO 2 , H 2 and hydrocarbons present in the samples (mainly components of gases produced in the pyrolysis process). A special study was made of the sulphur and chlorine content of all the fractions, as the presence of these elements could be problematic if the products are used as fuel. Tyre pyrolysis engenders a solid carbon residue that concentrates sulphur and chorine, with a relatively high calorific value, although not so high as that of the original tyre. The liquid fraction produced by the process has a high calorific value, which rises with the final temperature, up to 40 MJ/kg. The chlorine content of this fraction is negligible. Over 95% of the gas fraction, regardless of the final temperature, is composed of hydrocarbons of a low molecular weight and hydrogen, this fraction also appearing to be free of chlorine

  5. The procedure of alternative site selection within the report of the study group on the radioactive waste final repository selection process (AKEnd)

    International Nuclear Information System (INIS)

    Brenner, M.

    2005-01-01

    The paper discusses the results of the report of the study group on the radioactive waste final repository selection process with respect to the alternative site selection procedure. Key points of the report are the long-term safety, the alternativity of sites and the concept of one repository. The critique on this report is focussed on the topics site selection and licensing procedures, civil participation, the factor time and the question of cost

  6. Investigations of processes relevant to final storage before, during and after flooding of the Hope salt mine

    International Nuclear Information System (INIS)

    1986-07-01

    Due to the measurement and monitoring program in the partly flooded former Hope salt mine it is possible to obtain considerable new knowledge for the theoretical case of 'access of water or alkaline solution in the post-operation phase' for a final store in a salt deposit. An important part of the Hope research and development project was the selection and testing of suitable measuring equipment, data collection and transmission devices in difficult working conditions. The purpose of this seminar was to introduce the Hope research and development project and the results obtained so far to all the authorities and institutions taking part. 9 lectures recorded separately in data bases were held for this purpose. (orig./PW) [de

  7. Multiple primary malignancies of the liver and the colon: a complex diagnostic and decisional process with a final unanswered question.

    Science.gov (United States)

    Portolani, Nazario; Baiocchi, Gianluca; Baronchelli, Carla; Gheza, Federico; Giulini, Stefano Maria

    2014-03-29

    We herein present the case of a 78-year-old man with an incidental finding of a solid hepatic mass without symptoms and only a laparotomic cholecystectomy for acute cholecystitis in the past surgical history. A colonoscopy, a magnetic resonance imaging scan, a positron emission tomography scan, and a computed tomography scan completed the preoperative workup: a neoplastic lesion 4.3×3 cm in size was diagnosed at segments IV and V, associated with a neoplastic involvement of the splenic flexure without signs of colonic occlusion. After colonic resection, a frozen section on a granulomatous-like tissue at gastric border suggested a diagnosis of an adenocarcinoma of bilio-pancreatic type, changing the surgical strategy to include gastric resection and hepatic pedicle node dissection. The discussion turns around the idea that a final diagnosis of colon cancer with regional nodal involvement (pT3N1) and metastatic gallbladder cancer with multiple peritoneal seedings cannot be excluded.

  8. A process for treatment of residues from dry/semidry APC systems at municipal solid waste incinerators. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hjelmar, O. [VKI, Hoersholm (Denmark)] Holland, D. [FLS miljoe a/s, Valby (Denmark)] Poulsen, B. [KARA, Roskilde (Denmark)

    1997-08-01

    The main objective of the project has been to establish and test a process for treatment of residues from the semidry (and dry) lime injection based APC processes at MSWIs, which will ensure that the residues can be managed in an environmentally safe manner. In pursuit of this goal, the following activities have been carried out: Performance of pilot scale extractions (approximately 50 kg of residue per batch) at the KARA MSWI in Roskilde of semidry APC system residues in order to establish and optimize process conditions. The optimization includes consideration of the possibilities for subsequent treatment/stabilization of the extracted solid phase as well as the possibility of treatment and safe discharge/utilization of the extract; Performance of chemical characterization, hydrogeochemical model calculations and experimental work in order to improve the understanding of the mechanisms and factors which for several contaminants control the equilibrium between the solid and liquid phases, both in the short and the long germ, and to use this information to obtain an environmentally acceptable method for stabilization/treatment of the extracted residues while at the same time minimizing the necessary amount of additives; production of treated residues and performance of leaching tests on these to assess and demonstrate the effectiveness of the entire process (extraction + stabilization/treatment); Evaluation of the technical, economical and environmental consequences of full scale implementation of the process. (EG) EFP-94. 19 refs.

  9. Recovery of valuable chlorosilane intermediates by a novel waste conversion process. Technical report for phase IIIA (final) and phase IIIB (progress)

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, K.E.

    1998-10-01

    From July 1994 through May 1998, direct process residue (DPR) hydrogenolysis has been studied in the laboratory, at a small Pilot Plant, and finally at a larger Pilot Plant within Dow Corning`s Carrollton, Kentucky plant. The system reacts filtered DPR with monomer at high temperature and pressure. The process demonstrates DPR conversion up to 86%. The reaction product contains high concentrations of valuable monomers such as dimethyldichlorosilane and methyldichlorosilane. A larger DPR hydrogenolysis reactor based on these results is being designed for operation in Europe at Dow Corning`s Barry, Wales site.

  10. Food irradiation with emphasis on process control and acceptance in Asia. Proceedings of a final research co-ordination meeting

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-04-01

    The third phase of the Asian Regional Cooperative Project on Food Irradiation RPFI (Phase III) emphasized process control of pilot- and commercial scale irradiation of food according to the principle of the Codex General Standard for Irradiated Foods, and on gaining the acceptance of the process by governments, food industry and consumers. Phase III of the RPFI was funded by UNDP and was in operation from 1989-1993. Fifteen institutions in Australia, Bangladesh, China, India, Indonesia, Japan, the Republic of Korea, Pakistan, Philippines, Sri Lanka, Thailand and Viet Nam participated. Proper process control of irradiation with emphasis on dosimetry techniques was emphasized. A number of market testing, transportation trials and consumer acceptance studies was carried out during this period. Refs, figs, tabs.

  11. Application of subsurface vertical flow constructed wetlands to reject water treatment in dairy wastewater treatment plant.

    Science.gov (United States)

    Dąbrowski, Wojciech; Karolinczak, Beata; Gajewska, Magdalena; Wojciechowska, Ewa

    2017-01-01

    The paper presents the effects of applying subsurface vertical flow constructed wetlands (SS VF) for the treatment of reject water generated in the process of aerobic sewage sludge stabilization in the biggest dairy wastewater treatment plant (WWTP) in Poland. Two SS VF beds were built: bed (A) with 0.65 m depth and bed (B) with 1.0 m depth, planted with reeds. Beds were fed with reject water with hydraulic load of 0.1 m d -1 in order to establish the differences in treatment efficiency. During an eight-months research period, a high removal efficiency of predominant pollutants was shown: BOD 5 88.1% (A) and 90.5% (B); COD 84.5% (A) and 87.5% (B); TSS 87.6% (A) and 91.9% (B); TKN 82.4% (A) and 76.5% (B); N-NH 4 + 89.2% (A) and 85.7% (B); TP 30.2% (A) and 40.6% (B). There were not statistically significant differences in the removal efficiencies between bed (B) with 1.0 m depth and bed (A) with 0.65 m depth. The research indicated that SS VF beds could be successfully applied to reject water treatment in dairy WWTPs. The study proved that the use of SS VF beds in full scale in dairy WWTPs would result in a significant decrease in pollutants' load in reject water. In the analyzed case, decreasing the load of ammonia nitrogen was of greatest importance, as it constituted 58% of the total load treated in dairy WWTP and posed a hazard to the stability of the treatment process.

  12. Marginality and Social Rejection in Amiri Baraka's Slave Ship

    Directory of Open Access Journals (Sweden)

    Hamid Hammad Abed

    2016-11-01

    Full Text Available Marginality and social rejection are the most influential matters exploited by Baraka to intentionally criticize the American society.  More often than not, these two matters have become the scenes of major or minor acts of humiliation and dehumanization that threaten to violate the ethical rules of living. This paper aims at investigating the impact of marginality and social rejection on a number of black characters in Baraka's Slave Ship who are brought to America to be sold as commodities. It is divided into two sections and conclusion. Section one deals with Amiri Baraka’s dramatic thought and experience of marginality within the American society. The textual analysis of Slave Ship is investigated in section two. The significance of the study lies in its textual exploration of the impact of marginality and social rejection in subverting the American dream of democracy, freedom, and equality in Baraka’s Slave Ship.

  13. Study of Background Rejection Systems for the IXO Mission.

    Science.gov (United States)

    Laurent, Philippe; Limousin, O.; Tatischeff, V.

    2009-01-01

    The scientific performances of the IXO mission will necessitate a very low detector background level. This will imply thorough background simulations, and efficient background rejection systems. It necessitates also a very good knowledge of the detectors to be shielded. In APC, Paris, and CEA, Saclay, we got experience on these activities by conceiving and optimising in parallel the high energy detector and the active and passive background rejection system of the Simbol-X mission. Considering that this work may be naturally extended to other X-ray missions, we have initiated with CNES a R&D project on the study of background rejection systems mainly in view the IXO project. We will detail this activity in the poster.

  14. Prostanoids modulate inflammation and alloimmune responses during graft rejection

    Directory of Open Access Journals (Sweden)

    P.N. Rocha

    2005-12-01

    Full Text Available Acute rejection of a transplanted organ is characterized by intense inflammation within the graft. Yet, for many years transplant researchers have overlooked the role of classic mediators of inflammation such as prostaglandins and thromboxane (prostanoids in alloimmune responses. It has been demonstrated that local production of prostanoids within the allograft is increased during an episode of acute rejection and that these molecules are able to interfere with graft function by modulating vascular tone, capillary permeability, and platelet aggregation. Experimental data also suggest that prostanoids may participate in alloimmune responses by directly modulating T lymphocyte and antigen-presenting cell function. In the present paper, we provide a brief overview of the alloimmune response, of prostanoid biology, and discuss the available evidence for the role of prostaglandin E2 and thromboxane A2 in graft rejection.

  15. Research & Development of Materials/Processing Methods for Continuous Fiber Ceramic Composites (CFCC) Phase 2 Final Report.

    Energy Technology Data Exchange (ETDEWEB)

    Szweda, A.

    2001-01-01

    The Department of Energy's Continuous Fiber Ceramic Composites (CFCC) Initiative that begun in 1992 has led the way for Industry, Academia, and Government to carry out a 10 year R&D plan to develop CFCCs for these industrial applications. In Phase II of this program, Dow Corning has led a team of OEM's, composite fabricators, and Government Laboratories to develop polymer derived CFCC materials and processes for selected industrial applications. During this phase, Dow Corning carried extensive process development and representative component demonstration activities on gas turbine components, chemical pump components and heat treatment furnace components.

  16. Solar fuels and chemicals system design study (ammonia/nitric acid production process). Volume 2. Conceptual design. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1986-06-01

    As part of the Solar Central Receiver Fuels and Chemicals Program, Foster Wheeler Solar Development Corporation (FWSDC), under contract to Sandia National Laboratories-Livermore (SNLL), developed a conceptual design of a facility to produce ammonia and nitric acid using solar energy as the principal external source of process heat. In the selected process, ammonia is produced in an endothermic reaction within a steam methane (natural gas) reformer. The heat of reaction is provided by molten carbonate salt heated by both a solar central receiver and an exothermic ammonia-fired heater. After absorption by water, the product of the latter reaction is nitric acid.

  17. Development of an image processing system at the Technology Applications Center, UNM: Landsat image processing in mineral exploration and related activities. Final report

    International Nuclear Information System (INIS)

    Budge, T.K.

    1980-09-01

    This project was a demonstration of the capabilities of Landsat satellite image processing applied to the monitoring of mining activity in New Mexico. Study areas included the Navajo coal surface mine, the Jackpile uranium surface mine, and the potash mining district near Carlsbad, New Mexico. Computer classifications of a number of land use categories in these mines were presented and discussed. A literature review of a number of case studies concerning the use of Landsat image processing in mineral exploration and related activities was prepared. Included in this review is a discussion of the Landsat satellite system and the basics of computer image processing. Topics such as destriping, contrast stretches, atmospheric corrections, ratioing, and classification techniques are addressed. Summaries of the STANSORT II and ELAS software packages and the Technology Application Center's Digital Image Processing System (TDIPS) are presented

  18. A Longitudinal Study of Rejecting and Autonomy-Restrictive Parenting, Rejection Sensitivity, and Socioemotional Symptoms in Early Adolescents.

    Science.gov (United States)

    Rowe, Susan L; Gembeck, Melanie J Zimmer; Rudolph, Julia; Nesdale, Drew

    2015-08-01

    Rejection sensitivity (RS) has been defined as the tendency to readily perceive and overreact to interpersonal rejection. The primary aim of this study was to test key propositions of RS theory, namely that rejecting experiences in relationships with parents are antecedents of early adolescents' future RS and symptomatology. We also expanded this to consider autonomy-restrictive parenting, given the importance of autonomy in early adolescence. Participants were 601 early adolescents (age 9 to 13 years old, 51% boys) from three schools in Australia. Students completed questionnaires at school about parent and peer relationships, RS, loneliness, social anxiety, and depression at two times with a 14-month lag between assessments. Parents also reported on adolescents' difficulties at Time 1 (T1). It was anticipated that more experience of parental rejection, coercion, and psychological control would be associated with adolescents' escalating RS and symptoms over time, even after accounting for peer victimisation, and that RS would mediate associations between parenting and symptoms. Structural equation modelling supported these hypotheses. Parent coercion was associated with adolescents' increasing symptoms of social anxiety and RS over time, and parent psychological control was associated with increasing depressive symptoms over time. Indirect effects via RS were also found, with parent rejection and psychological control linked to higher T1 RS, which was then associated with increasing loneliness and RS. Lastly, in a separate model, peer victimisation and RS, but not parenting practices, were positively associated with concurrent parent reports of adolescents' difficulties.

  19. T-regulatory cells in chronic rejection versus stable grafts.

    Science.gov (United States)

    Al-Wedaie, Fatima; Farid, Eman; Tabbara, Khaled; El-Agroudy, Amgad E; Al-Ghareeb, Sumaya M

    2015-04-01

    Studying regulatory T cells in kidney allograft acceptance versus chronic rejection may help in the understanding of more mechanisms of immune tolerance and, in the future, may enable clinicians to induce immune tolerance and decrease the use of immunosuppressive drugs. The aim of the current study was to evaluate regulatory T cells in kidney transplant patients with stable graft versus transplant with biopsy-proven chronic rejection. The 3 groups that were studied included: kidney transplanted patients with no rejection episodes (n = 43); transplanted patients with biopsy-proven renal rejection (n = 27); and healthy age-matched nontransplanted individuals as controls (n = 42).The percentage of regulatory T cells (CD4+CD25+Foxp3+) in blood was determined by flow cytometry. The regulatory T cell percentage was significantly lower in chronic rejection patients than control or stable graft groups. No significant difference was observed in regulatory T cell percentage between the stable graft and control groups. In the stable graft group, patients on rapamycin had a significantly higher regulatory T cell percentage than patients on cyclosporine. No effect of donor type, infection, or duration after transplant was observed on regulatory T cell percentage. The results of the current study are consistent with previous studies addressing the function of regulatory T cells in inducing immunotolerance after kidney transplant. Considering the established role of regulatory T cells in graft maintenance and our observation of high regulatory T cell percentage in patients receiving rapamycin than cyclosporine, we recommend including rapamycin when possible in immunosuppressive protocols. The findings from the current study on the chronic rejection group support ongoing research of having treatment with regulatory T cells, which may constitute a novel, efficient antirejection therapy in the future.

  20. Consultancy on Large-Scale Submerged Aerobic Cultivation Process Design - Final Technical Report: February 1, 2016 -- June 30, 2016

    Energy Technology Data Exchange (ETDEWEB)

    Crater, Jason [Gemomatica, Inc., San Diego, CA (United States); Galleher, Connor [Gemomatica, Inc., San Diego, CA (United States); Lievense, Jeff [Gemomatica, Inc., San Diego, CA (United States)

    2017-05-12

    NREL is developing an advanced aerobic bubble column model using Aspen Custom Modeler (ACM). The objective of this work is to integrate the new fermentor model with existing techno-economic models in Aspen Plus and Excel to establish a new methodology for guiding process design. To assist this effort, NREL has contracted Genomatica to critique and make recommendations for improving NREL's bioreactor model and large scale aerobic bioreactor design for biologically producing lipids at commercial scale. Genomatica has highlighted a few areas for improving the functionality and effectiveness of the model. Genomatica recommends using a compartment model approach with an integrated black-box kinetic model of the production microbe. We also suggest including calculations for stirred tank reactors to extend the models functionality and adaptability for future process designs. Genomatica also suggests making several modifications to NREL's large-scale lipid production process design. The recommended process modifications are based on Genomatica's internal techno-economic assessment experience and are focused primarily on minimizing capital and operating costs. These recommendations include selecting/engineering a thermotolerant yeast strain with lipid excretion; using bubble column fermentors; increasing the size of production fermentors; reducing the number of vessels; employing semi-continuous operation; and recycling cell mass.

  1. Analysis of the permitting processes associated with exploration of Federal OCS leases. Final report. Volume II. Appendices

    Energy Technology Data Exchange (ETDEWEB)

    1980-11-01

    Under contract to the Office of Leasing Policy Development (LPDO), Jack Faucett Associates is currently undertaking the description and analysis of the Outer Continental Shelf (OCS) regulatory process to determine the nature of time delays that affect OCS production of oil and gas. This report represents the results of the first phase of research under this contract, the description and analysis of regulatory activity associated with exploration activities on the Federal OCS. Volume 1 contains the following three sections: (1) study results; (2) Federal regulatory activities during exploration of Federal OCS leases which involved the US Geological Survey, Environmental Protection Agency, US Coast Guard, Corps of Engineers, and National Ocean and Atmospheric Administration; and (3) state regulatory activities during exploration of Federal OCS leases of Alaska, California, Louisiana, Massachusetts, New Jersey, North Carolina and Texas. Volume II contains appendices of US Geological Survey, Environmental Protection Agency, Coast Guard, Corps of Engineers, the Coastal Zone Management Act, and Alaska. The major causes of delay in the regulatory process governing exploration was summarized in four broad categories: (1) the long and tedious process associated with the Environmental Protection Agency's implementation of the National Pollutant Discharge Elimination System Permit; (2) thelack of mandated time periods for the completion of individual activities in the permitting process; (3) the lack of overall coordination of OCS exploratory regulation; and (4) the inexperience of states, the Federal government and industry relating to the appropriate level of regulation for first-time lease sale areas.

  2. The development of an integrated multistaged fluid-bed retorting process. Final report, September 1990--August 1994

    Energy Technology Data Exchange (ETDEWEB)

    Carter, S.D.; Taulbee, D.N.; Stehn, J.L.; Vego, A.; Robl, T.L.

    1995-02-01

    This summarizes the development of the KENTORT II retorting process, which includes integral fluidized bed zones for pyrolysis, gasification, and combustion of oil shale. Purpose was to design and test the process at the 50-lb/hr scale. The program included bench- scale studies of coking and cracking reactions of shale oil vapors over processed shale particles to address issues of scaleup associated with solid-recycle retorting. The bench-scale studies showed that higher amounts of carbon coverage reduce the rate of subsequent carbon deposition by shale oil vapors onto processed shale particles; however carbon-covered materials were also active in terms of cracking and coking. Main focus was the 50-lb/hr KENTORT II PDU. Cold-flow modeling and shakedown were done before the PDU was made ready for operation. Seven mass-balanced, steady-state runs were completed within the window of design operating conditions. Goals were achieved: shale feedrate, run duration (10 hr), shale recirculation rates (4:1 to pyrolyzer and 10:1 to combustor), bed temperatures (pyrolyzer 530{degree}C, gasifier 750{degree}C, combustor 830{degree}C), and general operating stability. Highest oil yields (up to 109% of Fischer assay) were achieved for runs lasting {ge} 10 hours. High C content of the solids used for heat transfer to the pyrolysis zone contributed to the enhanced oil yield achieved.

  3. On-line testing of calibration of process instrumentation channels in nuclear power plants. Phase 2, Final report

    International Nuclear Information System (INIS)

    Hashemian, H.M.

    1995-11-01

    The nuclear industry is interested in automating the calibration of process instrumentation channels; this report provides key results of one of the sponsored projects to determine the validity of automated calibrations. Conclusion is that the normal outputs of instrument channels in nuclear plants can be monitored over a fuel cycle while the plant is operating to determine calibration drift in the field sensors and associated signal conversion and signal conditioning equipment. The procedure for on-line calibration tests involving calculating the deviation of each instrument channel from the best estimate of the process parameter that the instrument is measuring. Methods were evaluated for determining the best estimate. Deviation of each signal from the best estimate is updated frequently while the plant is operating and plotted vs time for entire fuel cycle, thereby providing time history plots that can reveal channel drift and other anomalies. Any instrument channel that exceeds allowable drift or channel accuracy band is then scheduled for calibration during a refueling outage or sooner. This provides calibration test results at the process operating point, one of the most critical points of the channel operation. This should suffice for most narrow-range instruments, although the calibration of some instruments can be verified at other points throughout their range. It should be pointed out that the calibration of some process signals such as the high pressure coolant injection flow in BWRs, which are normally off- scale during plant operation, can not be tested on-line

  4. 77 FR 1707 - National Toxicology Program (NTP) Final Process for Preparation of the Report on Carcinogens (RoC)

    Science.gov (United States)

    2012-01-11

    ... the RoC. The process is available on the NTP Web site ( http://ntp.niehs.nih.gov/go/rocprocess ) or by... Counselors public meeting (76 FR 68461) on December 15, 2011 ( http://ntp.niehs.nih.gov/go/9741 ). The NTP... Web site ( http://ntp.niehs.nih.gov/go/rocprocess ) or by contacting Dr. Lunn (see ADDRESSES...

  5. Final report on impact of catchment scale processes and climate change on cause-effect and recovery-chains

    NARCIS (Netherlands)

    Verdonschot, P.F.M.; Keizer-Vlek, H.E.; Spears, B.; Brucet, S.; Johnson, R.; Feld, C.; Kernan, M.

    2012-01-01

    Catchment wide integrated basin management requires knowledge on cause-effect and recovery chains within water bodies as well as on the interactions between water bodies and categories. In the WISER WP6.4 recovery processes in rivers, lakes and estuarine and coastal waters were evaluated. The major

  6. BCQ+: a body constitution questionnaire to assess Yang-Xu. Part I: establishment of a first final version through a Delphi process.

    Science.gov (United States)

    Su, Yi-Chang; Chen, Li-Li; Lin, Jun-Dai; Lin, Jui-Shan; Huang, Yi-Chia; Lai, Jim-Shoung

    2008-12-01

    Assessing an individual's level of Yang deficiency (Yang-Xu) by its manifestations is a frequent issue in traditional Chinese medicine (TCM) clinical trials. To this end, an objective, reliable and rigorous diagnostic tool is required. This study aimed to develop a first final version of the Yang-Xu Constitution Questionnaire. We conducted 3 steps to develop such an objective measurement tool: 1) the research team was formed and a panel of 26 experts was selected for the Delphi process; 2) items for the questionnaire were generated by literature review and a Delphi process; items were reworded into colloquial questions; face and content validity of the items were evaluated through a Delphi process again; 3) the difficulty of the questionnaire was evaluated in a pilot study with 81 subjects aged 20-60 years. The literature review retrieved 35 relevant items which matched the definition of 'constitution' and 'Yang-Xu'. After a first Delphi process, 22 items were retained and translated into colloquial questions. According to the second part of the Delphi process, the content validity index of each of the 22 questions ranged between 0.85-1. These 22 questions were evaluated by 81 subjects, 2 questions that were hard to tell the difference were combined; 3 questions were modified after the research team had discussed the participants' feedback. Finally, the questionnaire was established with 21 questions. This first final version of a questionnaire to assess Yang-Xu constitution with considerable face and content validity may serve as a basis to develop an advanced Yang-Xu questionnaire. 2008 S. Karger AG, Basel.

  7. A Longitudinal Rejection Sensitivity Model of Depression and Aggression: Unique Roles of Anxiety, Anger, Blame, Withdrawal and Retribution.

    Science.gov (United States)

    Zimmer-Gembeck, Melanie J; Nesdale, Drew; Webb, Haley J; Khatibi, Mhasa; Downey, Geraldine

    2016-10-01

    In this longitudinal study, attributional and social processes involved in symptoms of mental health problems (depressive symptoms and aggressive behavior) were identified by investigating anxious and angry rejection sensitivity (RS), causal attributions of self-blame and peer-blame, and responses to rejection threat of withdrawal and retribution. Young adolescents (N = 713, grades 5-7) completed questionnaires three times in their regular classrooms over 14 months. Participants who reported more self-blame for rejection were more likely to withdraw in response to rejection threat, and withdrawal and anxious RS were associated with increased depressive symptoms at T3 relative to T1. In contrast, adolescents higher in the angry form of RS and who reported more peer-blame for rejection were more likely to seek retribution, which in turn was associated with more overt/relational aggressive behavior at T3 relative to T1. Depressive symptom level measured at T1 also was associated with later RS and coping with withdrawal, and aggressive behavior at T1 was associated with later retribution. Sex of the participants did not moderate any longitudinal associations, and only one prospective path, from T1 depressive symptoms to T2 RS anxious, was moderated by age.

  8. Rejection of organic micro-pollutants from water by a tubular, hydrophilic pervaporative membrane designed for irrigation applications.

    Science.gov (United States)

    Sule, May N; Templeton, Michael R; Bond, Tom

    2016-01-01

    The links between chemical properties, including those relating to molecular size, solubility, hydrophobicity and vapour pressure, and rejection of model aromatic micro-pollutants by a tubular, hydrophilic polymer pervaporation membrane designed for irrigation applications were investigated. Open air experiments were conducted at room temperature for individual solutions of fluorene, naphthalene, phenol, 1,2-dichlorobenzene, 1,2-diethylbenzene and 2-phenoxyethanol. Percentage rejection generally increased with increased molecular size for the model micro-pollutants (47-86%). Molecular weight and log Kow had the strongest positive relationships with rejection, as demonstrated by respective correlation coefficients of r = 0.898 and 0.824. Rejection was also strongly negatively correlated with aqueous solubility and H-bond δ. However, properties which relate to vapour phase concentrations of the micro-pollutants were not well correlated with rejection. Thus, physicochemical separation processes, rather than vapour pressure, drive removal of aromatic contaminants by the investigated pervaporation tube. This expanded knowledge could be utilized in considering practical applications of pervaporative irrigation systems for treating organic-contaminated waters such as oilfield-produced waters.

  9. Synthesis of unsymmetrical dimethylhydrazine oxalate from rejected liquid rocket propellant

    Science.gov (United States)

    Mu, Xiaogang; Yang, Jingjing; Zhang, Youzhi

    2018-02-01

    The rejected liquid propellant unsymmetrical dimethylhydrazine (UDMH) was converted to UDMH oxalate, which has commercial value. The UDMH oxalate structure and stability were investigated by the Fourier transform infrared spectroscopy, nuclear magnetic resonance spectroscopy, differential scanning calorimetry, and ultraviolet-visible spectrophotometric analysis. The results indicate that UDMH oxalate has good thermal and aqueous solution stability, a melting point of 144 °C, an initial decomposition temperature of 180 °C, and a peak wavelength of UV in aqueous solution at λ = 204 nm. This disposal method of rejected UDMH is highly efficient and environmentally safe.

  10. Kidney graft rejection studies with labeled platelets and lymphocytes

    International Nuclear Information System (INIS)

    Martin-Comin, J.

    1986-01-01

    The usefulness of In-111-labelled platelets and lymphocyte scintigraphy in acute kidney graft rejection is evaluated in 155 patients. Blood cells were labelled with 100-150 uCi of In-111-oxine and reinjected. Subsequently patients were scanned once daily from 2 hours post-reinjection up to a week. The graft/contralateral area activity ratio was calculated in all scans. It is concluded that In-111-labelled platelets scintigraphy is nowadays the method of choice for acute kidney graft rejection diagnosis, especially in patients under cyclosporine immunosuppression. (author)

  11. Rechazo y retrasplante corneal Corneal rejection and re-transplantation

    Directory of Open Access Journals (Sweden)

    Miguel O Mokey Castellanos

    2007-06-01

    Full Text Available Se efectuó una investigación observacional análítica retrospectiva, sobre los transplantes corneales efectuados en el Servicio de Oftalmología del Hospital "Hermanos Ameijeiras. Rechazaron 76 pacientes, que se compararon con un control de 89 pacientes, que en un período similar no tuvieron rechazo. El queratocono fue la afección corneal que predominó. El primer lugar en los rechazos correspondió a queratoherpes (43,5 %. El menor índice de rechazo fue para el queratocono (8,8 %. Se analizó la multiplicidad de rechazos; y fue frecuente que se presentara un solo rechazo, aunque sí hubo congruencia entre el número de rechazos y la necesidad de retrasplantes. Se encontró que los resultados de la conducta médica o quirúrgica se relacionaban con la causa. Se calcula un índice de supervivencia (Kaplan-Meier, que concluye que en los primeros dos años existe menos posibilidad de aparición de rechazoAn retrospective observational analytical research was conducted on corneal transplants performed at Ophthalmological Service in “Hermanos Ameijeiras” hospital . Seventy six patients had graft rejection and were compared to a control group of 89 patients that did not present rejection in the same period of time. Keratoconus was the prevailing corneal problem. The highest rejection rate corresponded to keratoherpes (43,5% whereas the lowest rate was for keratoconus (8,8%. Multiplicity of rejections was analyzed and it was found that mostly one graft rejection occured, but number of rejections was associated with the need of re-transplantation. It was found that the results of medical or surgical performance were related to the cause of graft rejection. A survival index (Kaplan-Meier was estimated, which showed that occurence of graf rejection is less probable in the first two years

  12. What next after the rejection of Swiss electricity market legislation?

    International Nuclear Information System (INIS)

    Miolo, A.; Rechsteiner, S.

    2002-01-01

    This article discusses the situation in Switzerland after the rejection of new legislation on the liberalisation of the Swiss electricity market (Electricity Market Law, EMG) in a public vote in September 2002. The problems thus posed and the possibilities for further action available to those involved and affected are discussed. The legal situation after the rejection of the EMG is discussed with respect to Swiss regional structures and cantonal regulations. Three possible scenarios are discussed - the status quo, a solution to be provided by the electricity business or a Federal decree. The possibilities open to electricity enterprises for optimisation and the realisation of synergies to increase efficiency and competitiveness are discussed

  13. Development of biological coal gasification (MicGAS process). Final report, May 1, 1990--May 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    ARCTECH has developed a novel process (MicGAS) for direct, anaerobic biomethanation of coals. Biomethanation potential of coals of different ranks (Anthracite, bitumious, sub-bitumious, and lignites of different types), by various microbial consortia, was investigated. Studies on biogasification of Texas Lignite (TxL) were conducted with a proprietary microbial consortium, Mic-1, isolated from hind guts of soil eating termites (Zootermopsis and Nasutitermes sp.) and further improved at ARCTECH. Various microbial populations of the Mic-1 consortium carry out the multi-step MicGAS Process. First, the primary coal degraders, or hydrolytic microbes, degrade the coal to high molecular weight (MW) compounds. Then acedogens ferment the high MW compounds to low MW volatile fatty acids. The volatile fatty acids are converted to acetate by acetogens, and the methanogens complete the biomethanation by converting acetate and CO{sub 2} to methane.

  14. Process Parameter Evaluation and Optimization for Advanced Material Development Final Report CRADA No. TC-1234-96

    Energy Technology Data Exchange (ETDEWEB)

    Hrubesh, L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); McGann, T. W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-10-19

    This project was established as a three-year collaboration to produce and characterize · silica aerogels prepared by a Rapid Supercritical Extraction (RSCE) process to meet . BNA, Inc. application requirements. The objectives of this project were to study the parameters necessary to produce optimized aerogel parts with narrowly specified properties and establish the range and limits of the process for producing such aerogels. The project also included development of new aerogel materials useful for high temperature applications. The results of the project were expected to set the conditions necessary to produce quantities of aerogels having particular specifications such as size, shape, density, and mechanical strength. BNA, Inc. terminated the project on April 7, 1999, 10-months prior to the anticipated completion date, due to termination of corporate funding for the project. The technical accomplishments achieved are outlined in Paragraph C below.

  15. Process integration of the new blast furnace - Project Prima. Final report; Processintegration av den nya masugnen - Projekt Prima. Slutrapport

    Energy Technology Data Exchange (ETDEWEB)

    Ryman, Christer; Niemi, Tommi [Metallurgical Research Inst. AB, Luleaa (Sweden); Larsson, Mikael [Luleaa Technical Univ. (Sweden); Gyllenram, Rutger [Kobolde and Partners AB, Stockholm (Sweden)

    2004-05-01

    An one-dimensional static blast furnace model consisting of a mass balance and a heat balance model with an user friendly web interface has been developed. The model can be used for process optimisation and to compare different operating modes, but can also be used as a sub model for total analysis of the production site by means of process integration. It is also possible to use the model for planning of trials at an industrial or an experimental, blast furnace. The project has been executed by MEFOS (BF model development), Kobolde and Partners AB (system development) and Luleaa University of Technology (system integration). This report contains a brief model description, discussion of possible sources of errors, and examples of optimisation calculations. The project has been active from 2001 to 2003.

  16. Investigation of proposed process sequence for the array automated assembly task. Phase I and II. Final report, October 1, 1977-June 30, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Mardesich, N.; Garcia, A.; Eskenas, K.

    1980-08-01

    A selected process sequence for the low cost fabrication of photovoltaic modules was defined during this contract. Each part of the process sequence was looked at regarding its contribution to the overall dollars per watt cost. During the course of the research done, some of the initially included processes were dropped due to technological deficiencies. The printed dielectric diffusion mask, codiffusion of the n+ and p+ regions, wraparound front contacts and retention of the diffusion oxide for use as an AR coating were all the processes that were removed for this reason. Other process steps were retained to achieve the desired overall cost and efficiency. Square wafers, a polymeric spin-on PX-10 diffusion source, a p+ back surface field and silver front contacts are all processes that have been recommended for use in this program. The printed silver solderable pad for making contact to the aluminum back was replaced by an ultrasonically applied tin-zinc pad. Also, the texturized front surface was dropped as inappropriate for the sheet silicon likely to be available in 1986. Progress has also been made on the process sequence for module fabrication. A shift from bonding with a conformal coating to laminating with ethylene vinyl acetate and a glass superstrate is recommended for further module fabrication. The finalized process sequence is described.

  17. Treatment of coke-oven wastewater with the powdered activated carbon-contact stabilization activated sludge process. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Suidan, M.T.; Deady, M.A.; Gee, C.S.

    1983-11-01

    The objective of the study was to determine optimum parameters for the operation of an innovative process train used in the treatment of coke-over wastewater. The treatment process train consisted of a contact-stabilization activated sludge system with powdered activated carbon (PAC) addition, followed by activated sludge nitrification, followed by denitrification in an anoxic filter. The control and operating parameters evaluated during the study were: (a) the average mixed-liquor PAC concentration maintained in the contact-stabilization system, (b) the solids retention time practiced in the contact-stabilization system, and (c) the hydraulic detention time maintained in the contact aeration tank. Three identical treatement process trains were constructed and employed in this study. The coke-oven wastewater used for this investigation was fed to the treatment units at 30% strength. The first part of the study was devoted to determining the interactions between the mixed liquor PAC concentration and the solids retention time in the contact-stabilization tanks. Results showed that optimum overall system performance is attainable when the highest sludge age (30 day) and highest mixed liquor PAC concentration were practiced. During the second phase of the study, all three systems were operated at a 30 day solids retention time while different detention times of 1, 2/3 and 1/3 day were evaluated in the contact tank. PAC addition rates were maintained at the former levels and, consequently, reduced contact times entailed higher mixed liquor carbon concentrations. Once again, the system receiving the highest PAC addition rate of PAC exhibited the best overall performance. This system exhibited no deterioration in process performance as a result of decreased contact detention time. 72 references, 41 figures, 24 tables.

  18. Study of water recovery and solid waste processing for aerospace and domestic applications. Volume 1: Final report summary

    Science.gov (United States)

    Guarneri, C. A.; Reed, A.; Renman, R. E.

    1972-01-01

    This study of water reclamation and waste disposal is directed toward a more efficient utilization of natural resources. From an ecological standpoint improved methods of land use, water processing equipment, and ideal population profiles are investigated. Methods are described whereby significant reduction in water usage can be achieved by the adoption of presently available and practically applied technological concepts. Allowances are made for social, natural, and economic contingencies which are likely to occur up to the year 2000.

  19. Zirconium and technetium recovery and partitioning in the presence of actinides in modified Purex process for ATW program. Final report

    International Nuclear Information System (INIS)

    Dzekun, E.G.; Fedorov, Y.S.; Galkin, B.Y.; Lyubtsev, R.I.; Mashkin, A.N.; Mishin, E.N.; Zilberman, B.Y.

    1994-01-01

    The modified Purex process flowsheet is based on combination of all irradiated materials, their joint dissolution and reprocessing as a NPP spent fuel solution with abnormal Pu content after addition of recycled depleted U concentrate. Some groups of long-lived radionuclides could be completely recovered and localized at the stage of extraction reprocessing using 30% TBP. Studies were conducted for 10 y to develop the process for recovery, concentration, and localization of U, Pu, Np, Tc, and Zr within 1st extraction cycle. Actinides are recovered from high-level raffinate of this cycle after evaporation and feed adjustment. Results in this report show that combined deep recovery of several elements from highly irradiated materials by TBP extraction, for further transmutation, is possible. Selective stripping of Zr from solvent phase containing U, Pu, Np, and Tc is quite effective. Development of the modified Purex process is not complete; main problem to be solved should be oxide separation from the loop and permissible storage duration before reprocessing and reuse in the loop

  20. Investigation of deep inelastic scattering processes involving large p$_{t}$ direct photons in the final state

    CERN Multimedia

    2002-01-01

    This experiment will investigate various aspects of photon-parton scattering and will be performed in the H2 beam of the SPS North Area with high intensity hadron beams up to 350 GeV/c. \\\\\\\\ a) The directly produced photon yield in deep inelastic hadron-hadron collisions. Large p$_{t}$ direct photons from hadronic interactions are presumably a result of a simple annihilation process of quarks and antiquarks or of a QCD-Compton process. The relative contribution of the two processes can be studied by using various incident beam projectiles $\\pi^{+}, \\pi^{-}, p$ and in the future $\\bar{p}$. \\\\\\\\b) The correlations between directly produced photons and their accompanying hadronic jets. We will examine events with a large p$_{t}$ direct photon for away-side jets. If jets are recognised their properties will be investigated. Differences between a gluon and a quark jet may become observable by comparing reactions where valence quark annihilations (away-side jet originates from a gluon) dominate over the QDC-Compton...

  1. Demonstration and evaluation of the CORPEX trademark Nuclear Decontamination Process, Technical task plan No. SR152005. Final Report

    International Nuclear Information System (INIS)

    May, C.G.

    1997-01-01

    In June, 1995, the Decontamination and Decommissioning Focus Area funded a demonstration of the CORPEX Nuclear Decontamination Process in an Old Metallography Laboratory glovebox at the Savannah River Site. The objective of the demonstration was to prove the effectiveness of a new and innovative technology that would reduce the risks associated with future cleanups of plutonium-238 contaminated equipment in the DOE complex. After facility and vendor preparations in support of the demonstration, Westinghouse Savannah River Company (WSRC) was informed by the vendor that the chemistry proposed for use in the decontamination process was not effective on sintered plutonium, which was the form of plutonium in the selected glovebox. After further technical evaluation, the demonstration was canceled. This report describes the work performed in support of the demonstration and the present status of the project. The CORPEX chemical process is a nondestructive cleaning method that removes only the contaminant and the matrix that fixed the contaminant to the surface. It does not damage the substrate. The cleaning agent is destroyed by the addition of proprietary oxidizers, leaving water, carbon dioxide and nitrogen gases, and a sludge as waste

  2. Improving regulatory effectiveness in Federal/State siting actions. Need for power: determinants in the state decisionmaking processes. Final report

    International Nuclear Information System (INIS)

    Noble, J.B.; Hemphill, J.B.

    1978-03-01

    The Department of Energy's Nuclear Siting and Licensing Act of 1978 (S. 2775; H. R. 11704) proposes Federal/State coordination in need for facility decisionmaking for nuclear power stations. The present study examines the decisionmaking criteria used by forty-four States in making a determination of need for power/facility. Specific criteria are identified along with the number of States which make those criteria a primary or a secondary consideration in determining need for facility. Individual profiles of the studied States' decisionmaking criteria are provided. In addition, the study examines the different organizational and functional patterns found in the States' regulatory process to certificate power stations. The coordination or lack of coordination of the issuance of associated environmental permits required for power stations is outlined for each State. Information concerning States' rate treatment of expenses associated with the construction and operation of a power station is provided. The relationship between the need for power decisionmaking process and the ratemaking process is explored

  3. Zirconium and technetium recovery and partitioning in the presence of actinides in modified Purex process for ATW program. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Dzekun, E.G.; Fedorov, Y.S.; Galkin, B.Y.; Lyubtsev, R.I.; Mashkin, A.N.; Mishin, E.N.; Zilberman, B.Y. [Radievyj Inst., Leningrad (Russian Federation)

    1994-12-31

    The modified Purex process flowsheet is based on combination of all irradiated materials, their joint dissolution and reprocessing as a NPP spent fuel solution with abnormal Pu content after addition of recycled depleted U concentrate. Some groups of long-lived radionuclides could be completely recovered and localized at the stage of extraction reprocessing using 30% TBP. Studies were conducted for 10 y to develop the process for recovery, concentration, and localization of U, Pu, Np, Tc, and Zr within 1st extraction cycle. Actinides are recovered from high-level raffinate of this cycle after evaporation and feed adjustment. Results in this report show that combined deep recovery of several elements from highly irradiated materials by TBP extraction, for further transmutation, is possible. Selective stripping of Zr from solvent phase containing U, Pu, Np, and Tc is quite effective. Development of the modified Purex process is not complete; main problem to be solved should be oxide separation from the loop and permissible storage duration before reprocessing and reuse in the loop.

  4. VIP Project - Visual based intelligent process control. Final report; VIP Projekt - Visuell basierte intelligente Prozessfuehrung. Fachlicher Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Moreno Rueda, R.

    2001-09-01

    This BMBF project comprised the development and testing of new process control strategies involving local resolution sensors and efficient simulation models. A system comprising a video section and a spectroscopic section is presented here. Further data can be processed in the master PC if desired. By analyzing every single burner, it is possible to analyze and optimize the complete combustion process. [German] Im Rahmen des BMBF-Projektes 'Visuell basierte Intelligente Prozessfuehrung fuer grosstechnische Feuerungsprozesse' wurden neuartige Prozessfuehrungsstrategien durch die Verbindung von ortsaufloesender Sensorik und leistungsfaehige Simulationsmodellen entwickelt und erprobt. Zur Loesung der gestellten Aufgaben wurde das hier dargestellte Gesamtsystem, bestehend aus Video- und Spektroskopie entwickelt. Ueber die Darstellung hinaus koennen im Master-PC auch die Daten weiterer Lanzen/Brenner verarbeitet werden. Die Vorortschraenke wie Kuehlmedien-Steuerschrank und Elektro-Steuerschrank koennen je nach Kesselabmassen auch fuer mehr als 2 Lanzen zusammengafasst werden. Durch die Betrachtung jedes einzelnen Brenners, wird es moeglich die Feuerung ganzheitlich und zeitgleich zu erfassen, zu beurteilen und zu optimieren. (orig.)

  5. Multiquadrant Subtenon Triamcinolone Injection for Acute Corneal Graft Rejection: A Case Report

    Directory of Open Access Journals (Sweden)

    Sunali Goyal

    2017-05-01

    Full Text Available Background: We report a case of reversal of an acute corneal graft rejection following multiquadrant subtenon triamcinolone injection. Case Presentation: A 19-year-old woman who had acute corneal graft rejection failed to show resolution of the graft rejection after standard treatment with systemic, intravenous, and topical steroids. The graft rejection, however, responded to injection of triamcinolone in multiple subtenon quadrants. Conclusions: For corneal graft rejection, multiquadrant subtenon triamcinolone injections may be a safe adjunct to systemic treatment.

  6. Indirect Effects of Emotion Regulation on Peer Acceptance and Rejection: The Roles of Positive and Negative Social Behaviors

    Science.gov (United States)

    Blair, Bethany L.; Gangel, Meghan J.; Perry, Nicole B.; O'Brien, Marion; Calkins, Susan D.; Keane, Susan P.; Shanahan, Lilly

    2016-01-01

    A growing body of literature indicates that childhood emotion regulation predicts later success with peers, yet little is known about the processes through which this association occurs. The current study examined mechanisms through which emotion regulation was associated with later peer acceptance and peer rejection, controlling for earlier…

  7. Reject/repeat analysis and the effect prior film viewing has on a department's reject/repeat rate

    International Nuclear Information System (INIS)

    Clark, P.A.; Hogg, P.

    2003-01-01

    Purpose: Achieving cost-effectiveness within the NHS is an old initiative but one that has again been highlighted by recent government policies (The New NHS-Modern and Dependable, Stationary Office, London, 1997). It has been reiterated that it is the responsibility of individual Trusts to devise means to provide such a service. Reject/repeat analyses have long been the primary tool used to assess the cost-effectiveness of radiography departments (Quality Assurance in Diagnostic Radiology, WHO, Geneva, 1982). This research paper examines an in-house initiative (viewing patients' previous films) commonly employed in other Health Trusts in order to reduce departmental repeat/reject rates. Method: Three hundred orthopaedic patients with hip, knee and ankle prostheses were included in a reject/repeat analysis. The aim was to investigate whether or not viewing patient's previous relevant radiographs would be advantageous to the practicing radiographer. This was done through an audit cycle consisting of two audit periods each lasting for 3 months. The primary audit period recorded the baseline repeat/reject rate, with the secondary audit period recording the repeat/reject rate under an experimental condition of viewing the relevant radiographs. Results: The baseline audit revealed repeat rates of 33% in orthopaedic patients with hip, knee and ankle prostheses. The availability of prior film viewing to the radiographer reduced this repeat rate to 10.6%. Conclusion: Prior film viewing dramatically reduced the department's repeat/reject rate by 22.4%. This provides scope for significant patient dose reductions as well as reducing departmental film expenses. This is an underestimated initiative and should be used appropriately in routine clinical practice

  8. Dosimetry for radiation processing. Final report of the co-ordinated research project on characterization and evaluation of high dose dosimetry techniques for quality assurance in radiation processing

    International Nuclear Information System (INIS)

    2000-06-01

    In many Member States the use of large cobalt-60 gamma ray facilities and electron beam accelerators with beam energies from about 0.1 to 10 MeV for industrial processing continues to increase. For these processes, quality assurance relies on the application of well established dosimetry systems and procedures. This is especially the case for health regulated processes, such as the radiation sterilization of health care products, and the irradiation of food to eliminate pathogenic organisms or to control insect pests. A co-ordinated research project (CRP) was initiated by the IAEA in June 1995. Research contracts and research agreements in areas of high dose dosimetry were initiated to meet these challenges. The major goals of this CRP were to investigate the parameters that influence the response of dosimeters and to develop reference and transfer dosimetry techniques, especially for electron beams of energy less than 4 MeV and for high energy X ray sources (up to 5 MV). These will help to unify the radiation measurements performed by different radiation processing facilities and other high dose dosimetry users in Member States and encourage efforts to obtain traceability to primary and secondary standards laboratories. It will also aim to strengthen and expand the present International Dose Assurance Service (IDAS) provided by the IAEA

  9. Technical report on material selection and processing guidelines for BWR [boiling water reactor] coolant pressure boundary piping: Final report

    International Nuclear Information System (INIS)

    Hazelton, W.S.; Koo, W.H.

    1988-01-01

    This report provides the technical bases for the NRC staff's revised recommended methods to control the intergranular stress corrosion cracking susceptibility of BWR piping. For piping that does not fully comply with the material selection, testing, and processing guideline combinations of this document, varying degrees of augmented inservice inspection are recommended. This revision also includes guidance and NRC staff recommendations (not requirements) regarding crack evaluation and weld overlay repair methods for long-term operation or for continuing interim operation of plants until a more permanent solution is implemented

  10. Situation concerning public information about and involvement in the decision-making processes in the nuclear sector. Final report

    International Nuclear Information System (INIS)

    Gadbois, S.; Heriard Dubreuil, G.; Vaillant, L.; Schneider, T.; Paterson, J.; Dawson, M.; Borg Barthet, J.; Prades, A.; Lopez, M.; Sala, R.

    2007-01-01

    The European Commission Directorate General for Energy and Transport (EC DGTREN) launched a study on 'the situation concerning public information about and involvement in decision-making processes in the nuclear sector' in January 2005. The main goal of this project was to inform the EC DGTREN and interested parties of recent developments in the Member States and to provide opportunities for decision-makers and stakeholders at local, national and EU level to exchange views. This study is based on the analysis of opinion polls, regulation and case studies where public information and involvement are a key dimension in the decision-making process and where innovative approaches have been observed. The research material and proposals were presented and discussed at a workshop with 50 delegates, representing the various stakeholders concerned by nuclear activities in Europe. As testified by recent opinion polls and feedback from case studies, there is a strong public demand for more participation in decision-making processes relating to the environment, and nuclear issues specifically. There is an increasing expectation that the phase of decision-framing which determines the scope and objectives of a regulation or of a decision on an industrial facility, involves not only experts and politics, but also NGOs, independent experts, local actors, etc. This expectation is now supported by significant legislation at EU and national levels, the foundation stone of which is the 'Aarhus Convention on the Access to Information, Public Participation in Decision-Making and Access to Justice in Environmental Matters' (1998). One can find different but convergent rationales behind these developments. On the one hand, there is a consideration that nuclear technologies have a potential impact on the public and accordingly require that their development involves affected parties. On the other hand, the problems raised by nuclear activities have an impact at several levels (local

  11. Situation concerning public information about and involvement in the decision-making processes in the nuclear sector. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Gadbois, S.; Heriard Dubreuil, G. [Mutadis, 75 - Paris (France); Vaillant, L.; Schneider, T. [Centre d' Etude sur l' Evaluation de la Protection dans le Domaine Nucleaire - CEPN, 92 - Fontenay aux Roses (France); Paterson, J.; Dawson, M.; Borg Barthet, J. [Aberdeen Univ. (United Kingdom); Prades, A.; Lopez, M.; Sala, R. [CIEMAT, Barcelona (Spain)

    2007-07-01

    The European Commission Directorate General for Energy and Transport (EC DGTREN) launched a study on 'the situation concerning public information about and involvement in decision-making processes in the nuclear sector' in January 2005. The main goal of this project was to inform the EC DGTREN and interested parties of recent developments in the Member States and to provide opportunities for decision-makers and stakeholders at local, national and EU level to exchange views. This study is based on the analysis of opinion polls, regulation and case studies where public information and involvement are a key dimension in the decision-making process and where innovative approaches have been observed. The research material and proposals were presented and discussed at a workshop with 50 delegates, representing the various stakeholders concerned by nuclear activities in Europe. As testified by recent opinion polls and feedback from case studies, there is a strong public demand for more participation in decision-making processes relating to the environment, and nuclear issues specifically. There is an increasing expectation that the phase of decision-framing which determines the scope and objectives of a regulation or of a decision on an industrial facility, involves not only experts and politics, but also NGOs, independent experts, local actors, etc. This expectation is now supported by significant legislation at EU and national levels, the foundation stone of which is the 'Aarhus Convention on the Access to Information, Public Participation in Decision-Making and Access to Justice in Environmental Matters' (1998). One can find different but convergent rationales behind these developments. On the one hand, there is a consideration that nuclear technologies have a potential impact on the public and accordingly require that their development involves affected parties. On the other hand, the problems raised by nuclear activities have an impact at several

  12. Measuring the In-Process Figure, Final Prescription, and System Alignment of Large Optics and Segmented Mirrors Using Lidar Metrology

    Science.gov (United States)

    Ohl, Raymond; Slotwinski, Anthony; Eegholm, Bente; Saif, Babak

    2011-01-01

    The fabrication of large optics is traditionally a slow process, and fabrication capability is often limited by measurement capability. W hile techniques exist to measure mirror figure with nanometer precis ion, measurements of large-mirror prescription are typically limited to submillimeter accuracy. Using a lidar instrument enables one to measure the optical surface rough figure and prescription in virtuall y all phases of fabrication without moving the mirror from its polis hing setup. This technology improves the uncertainty of mirror presc ription measurement to the micron-regime.

  13. Antibody-mediated rejection in kidney transplantation: a review of pathophysiology, diagnosis, and treatment options.

    Science.gov (United States)

    Kim, Miae; Martin, Spencer T; Townsend, Keri R; Gabardi, Steven

    2014-07-01

    Antibody-mediated rejection (AMR), also known as B-cell-mediated or humoral rejection, is a significant complication after kidney transplantation that carries a poor prognosis. Although fewer than 10% of kidney transplant patients experience AMR, as many as 30% of these patients experience graft loss as a consequence. Although AMR is mediated by antibodies against an allograft and results in histologic changes in allograft vasculature that differ from cellular rejection, it has not been recognized as a separate disease process until recently. With an improved understanding about the importance of the development of antibodies against allografts as well as complement activation, significant advances have occurred in the treatment of AMR. The standard of care for AMR includes plasmapheresis and intravenous immunoglobulin that remove and neutralize antibodies, respectively. Agents targeting B cells (rituximab and alemtuzumab), plasma cells (bortezomib), and the complement system (eculizumab) have also been used successfully to treat AMR in kidney transplant recipients. However, the high cost of these medications, their use for unlabeled indications, and a lack of prospective studies evaluating their efficacy and safety limit the routine use of these agents in the treatment of AMR in kidney transplant recipients. © 2014 Pharmacotherapy Publications, Inc.

  14. Anxious and angry rejection sensitivity, social withdrawal, and retribution in high and low ambiguous situations.

    Science.gov (United States)

    Zimmer-Gembeck, Melanie J; Nesdale, Drew

    2013-02-01

    Rejection sensitivity (RS) is a tendency to expect, perceive, and overreact to rejection. Our objective was to examine whether anxious and angry RS have specific associations with negative social reactions, and whether responses are intensified in situations of high rejection ambiguity. In two studies, youth (N = 464 and N = 371) reported their RS and anticipated responses to social scenarios. In Study 1, all scenarios portrayed overt rejection events. In Study 2, participants were randomly assigned to conditions portraying overt or ambiguous rejection. Greater rejection expectation was associated with more negative reactions to rejection. Moreover, as expected, anxiety about rejection was uniquely associated with withdrawal, and anger about rejection was uniquely associated with retribution (i.e., reactive aggression). In the second study, RS persons responded more negatively than others to both overt and high ambiguous rejections, but retribution was intensified among participants high in rejection expectation when rejection was ambiguous, and withdrawal was intensified among participants high in anxious RS in overt rejection situations. Consistent with the revised RS model, there are different patterns of emotions, cognitions, and behaviors in response to high and low ambiguous rejection events, which are heightened in youth sensitive to rejection. © 2012, Wiley Periodicals, Inc.

  15. Potential radiological impacts of recovery of uranium from wet-process phosphoric acid. Final report to the Environmental Protection Agency

    International Nuclear Information System (INIS)

    Davis, W. Jr.; Haywood, F.F.; Danek, J.L.; Moore, R.E.; Wagner, E.B.; Rupp, E.M.

    1979-01-01

    A study was made to determine the radiological impacts associated with recovery of uranium from wet-process (WP) phosphoric acid in central Florida. Removal of U and other radionuclides from phosphoric acid prevents their distribution on farm lands and urban gardens and grasses via fertilizers; this results in a positive impact (decreased dose commitment) on the associated populations. This study considers the potential negative impacts of current and project recovery processes in a site-specific manner using detailed state-of-the-art methodologies. Positive impacts are treated in a generic sense using U.S. average values for important variables such as average and maximum fertilizer application rates and quantities of radionuclides in fertilizer. Three model plants to recover U from WP phosphoric acid were selected and source terms for release of radionuclides are developed for all three and for two treatment methods for airborne particulates. Costs for radwaste treatment were developed. Field measurements were conducted at the only commercial uranium recovery plant in operation. Radiological doses to the population surrounding release points during plant operation were estimated

  16. Rapid Tooling for Functional Prototype of Metal Mold Processes Final Report CRADA No. TC-1032-98

    Energy Technology Data Exchange (ETDEWEB)

    Heestand, G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Jaskolski, T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-10-16

    Production inserts for die-casting were generally fabricated from materials with sufficient strength and· good wear properties at casting temperatures for long life. Frequently tool steels were used and machining was done with a combination of. conventional and Electric Discharge Machining (EDM) with some handwork, an expensive and time consuming process, partilly for prototype work. We proposed electron beam physical vapor deposition (EBPVD) as a process for rapid fabrication of dies. Metals, ranging from low melting point to refractory metals (Ta, Mo, etc.), would be evaporated and deposited at high rates (-2mm/hr.). Alloys could be easily evaporated and deposited if their constituent vapor pressures were similar and with more difficulty if they were not. Of course, layering of different materials was possible if required for a specific application. For example, a hard surface layer followed by a tough steel and backed by a high thermal conductivity (possibly cooled) copper layer could be fabricated. Electron-beam deposits exhibited 100% density and lull strength when deposited at a substrate (mandrel) temperature that was a substantial fraction of the deposited material's melting point. There were several materials that could have the required high temperature properties and ease of fabrication required for such a mandrel. We had successfully used graphite, machined from free formed objects with a replicator, to produce aluminum-bronze test molds. There were several parting layer materials of interest, but the ideal material depended upon the specific application.

  17. Radioactive waste management: a comparative study of national decision-making processes. Final report, September 15, 1978-December 31, 1979

    International Nuclear Information System (INIS)

    Zinberg, D.S.; Deese, D.

    1980-01-01

    A report is presented resulting from a comparative study of national decision-making processes in radioactive waste management. By seeking out the variations among the socio-political and institutional components of the nuclear power and radioactive waste policies in ten countries, the authors have attempted to identify means to improve national and international responses to a seemingly intractable problem, the management of wastes from military and commercial nuclear programs worldwide. Efforts were focused on evaluation of comparative national policy formulation processes. Mapping national programs in conjunction with social, political and administrative structure and comparing the similarities and differences among them has revealed six major issues: (1) technological bias in decision-making; (2) lack of natioal strategies for the RWM programs; (3) fragmentation of governmental power structures; (4) crippled national regulatory bodies; (5) complex and competing relations among local, state and federal levels of government; and (6) increased importance of non-governmental actors and public participation. The first two issues are overarching, encompassing the fundamental approach to policy, whereas the last four describe more specific aspects of the decision-making structures

  18. The compositional study of nitrogen and oxygen compounds in products of heavy oil primary and secondary upgrading processes. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Chmielowiec, J.

    1986-02-01

    The primary objective was to characterize nitrogen and oxygen compound types in the upgraded products derived from Athabasca bitumen. Nitrogen compounds, depending on their nature and concentrations, in charge stocks to catalytic processess (hydro-processes and reforming) can severely limit or poison the catalyst activity. Oxygen compounds are corrosive (especially naphthenic acids) and can promote gum formation as part of the deterioration of the hydrocarbons in the petroleum product. A secondary objective was to evaluate the advantages and limitations of in-house mass spectrometry and infrared spectroscopy methods for analyzing specific classes of polar compounds in naphthas, middle distillates, and gas oils. An analytical procedure that was based on the discrimination of polar compound classes using liquid chromatography followed by mass spectrometric analysis was tested. The chemical intelligence on the fractions obtained from Athabasca bitumen and its upgrading products has been advanced by determining structural characteristics of the nitrogen and oxygen components. This report describes the determination of the distributions of nitrogen and oxygen compounds in samples from various process streams. This procedure is capable of providing information useful for evaluating hydrodenitrogenation and hydrodeoxygenation reactions.

  19. Staged air biomass gasification. Operation experiences and process optimisation. Final report; Trinopdelt forgasning. Erfaringsindhentning og optimering. Slutrapport

    Energy Technology Data Exchange (ETDEWEB)

    Houmann Jakobsen, H.; Kyster, L.

    2011-05-15

    The project's aim was to optimize the drying plant for wood chips, and to accumulate operating experience from the entire facility through a half year of operation. Based on theoretical considerations the potential for improving the drying process was evaluated. Possibilities to take into the flue gas humidity as a control parameter was studied, but after a few simple measurements it was concluded that the most relevant change was to seal of the plant to minimize the risk of ingress of cold air into the fuel. After finding the cause of the leaking a new fuel inlet to the dryer has been constructed, and the original, leaky rotary valve has been replaced. Both changes have led to a significant improvement of the drying plant. Operational experience from plant operation showed with clarity that the energy loss from charcoal in the ashes was significantly higher than desirable. The volume meant that the handling and disposal of charcoal in itself constituted a major operational cost. At the end of the project, promising experiments with incorporation of an extra step in the gasification process were carried out. It seems to be an effective method to convert the remaining carbon matter to flammable gas and increase gas generator efficiency. Work on reducing charcoal production now continues in a new project. (ln)

  20. Recovery and recycling of uranium from rejected coated particles for compact high temperature reactors

    Energy Technology Data Exchange (ETDEWEB)

    Pai, Rajesh V., E-mail: pairajesh007@gmail.com [Fuel Chemistry Division, Bhabha Atomic Research Centre, Mumbai (India); Mollick, P.K. [Powder Metallurgy Division, Bhabha Atomic Research Centre, Mumbai (India); Kumar, Ashok [Fuel Chemistry Division, Bhabha Atomic Research Centre, Mumbai (India); Banerjee, J. [Radiometullurgy Division, Bhabha Atomic Research Centre, Mumbai (India); Radhakrishna, J. [Fuel Chemistry Division, Bhabha Atomic Research Centre, Mumbai (India); Chakravartty, J.K. [Powder Metallurgy Division, Bhabha Atomic Research Centre, Mumbai (India)

    2016-05-15

    UO{sub 2} microspheres prepared by internal gelation technique were coated with pyrolytic carbon and silicon carbide using CVD technique. The particles which were not meeting the specifications were rejected. The rejected/failed UO{sub 2} based coated particles prepared by CVD technique was used for oxidation and recovery and recycling. The oxidation behaviour of sintered UO{sub 2} microspheres coated with different layers of carbon and SiC was studied by thermal techniques to develop a method for recycling and recovery of uranium from the failed/rejected coated particles. It was observed that the complete removal of outer carbon from the spheres is difficult. The crushing of microspheres enabled easier accessibility of oxygen and oxidation of carbon and uranium at 800–1000 °C. With the optimized process of multiple crushing using die & plunger and sieving the broken coated layers, we could recycle around fifty percent of the UO{sub 2} microspheres which could be directly recoated. The rest of the particles were recycled using a wet recycling method. - Highlights: • The oxidation behaviour of coated particles was studied in air, O{sub 2} and moist O{sub 2}. • It was observed that coated layers cannot be completely removed by mere oxidation. • Complete recovery of uranium from the rejected coated particles has been carried out using a combination of dry and wet recovery scheme. • A crushing step prior to oxidation is needed for full recovery of uranium from the coated particles.