SIMS: The SLAC Industrial Measurement System

International Nuclear Information System (INIS)

Bell, B.

1990-01-01

Kern was the first survey company to market an Industrial Measurement System when it released ECDS (Electronic Coordinate Determination System) in the mid-1980s. Originally written for the PDP-11, a version was later released for the PC (ECDS-PC). SLAC purchased this system in 1986 and immediately began to use it for the alignment of the SLC (Stanford Linear Collider). Although ECDS enabled SLAC to perform tasks with a speed never before achieved, they experienced limitations in the software. Since Kern proved unresponsive and SLAC was unable to purchase the source code for any amount of money, they set about writing their own portions of code. They first wrote a system of menus tailored for their specific alignment tasks, and disabled much of the ECDS menu structure. Due to dissatisfaction with the ECDS bundle adjustment program, they wrote their own bundle adjustment in 1988. A further step towarad having their own complete IMS was to develop a data capture program, a task which has been underway since the beginning of this year. They do not yet have data analysis features that are fully integrated, but they do have stand-alone packages that have been written at SLAC. When they first started tinkering with ECDS there was no intention of developing a complete system, but they now have all the elements of such a system - SIMS, the SLAC Industrial Measurement System

An overview of the SLAC results

International Nuclear Information System (INIS)

Prescott, C.Y.

1996-03-01

The history of nucleon spin-structure measurements goes back to the early days of inelastic electron scattering at SLAC, when Vernon Hughes came with a proposal to accelerate polarized electrons to high energy and to study inelastic scattering from a polarized proton target. The quark model of the proton was new at the time, and the spin-dependent structure functions were an excellent testing ground for that model. The proposal developed into an experiment which became SLAC experiment E80. Subsequent experiments followed those early studies, leading to E130 at SLAC, then EMC at CERN, and a host of later experiments. In 1988 the EMC Collaboration published the first data to reach low x. The asymmetries EMC observed fell below quark model expectations, and the experimentally measured proton sum rule indicated that the spin of the quarks contributed little to the proton spin. The subject of nucleon spin-dependent structure functions was stimulated by this surprising result from EMC. The continuation of the spin-structure studies at SLAC, which have been very active in recent years, was stimulated by the successful development of high-intensity beams of polarized electrons. Table 1 lists the past, present, and planned programs and experiments that grew out of the early work. The rest of the report is divided into the following topics: polarized electrons; polarimetry; the SLAC spectrometers; radiative corrections; the proton measurements; neutron targets; the deuterium and 3 He data; the g 2 structure function; and the 50 GeV upgrade of the SLC

SLAC three-body partial wave analysis system

International Nuclear Information System (INIS)

Aston, D.; Lasinski, T.A.; Sinervo, P.K.

1985-10-01

We present a heuristic description of the SLAC-LBL three-meson partial wave model, and describe how we have implemented it at SLAC. The discussion details the assumptions of the model and the analysis, and emphasizes the methods we have used to prepare and fit the data. 28 refs., 12 figs., 1 tab

SLAC High Gradient Testing of a KEK X-Band Accelerator Structure

International Nuclear Information System (INIS)

Loewen, Rod

2000-01-01

The high accelerating gradients required for future linear colliders demands a better study of field emission and RF breakdown in accelerator structures. Changes in structure geometry, vacuum pumping, fabrication methods, and surface finish can all potentially impact the conditioning process, dark current emission, and peak RF power handling capability. Recent tests at SLAC of KEK's ''M2'' travelling wave x-band accelerator section provides an opportunity to investigate some of these effects by comparing its performance to previously high power tested structures at SLAC. In addition to studying ultimate power limitations, this test also demonstrates the use of computer automated conditioning to reach practical, achievable gradients

Results of the SLAC LCLS Gun High-Power RF Tests

International Nuclear Information System (INIS)

Dowell, D.H.; Jongewaard, E.; Limborg-Deprey, C.; Schmerge, J.F.; Li, Z.; Xiao, L.; Wang, J.; Lewandowski, J.; Vlieks, A.

2007-01-01

The beam quality and operational requirements for the Linac Coherent Light Source (LCLS) currently being constructed at SLAC are exceptional, requiring the design of a new RF photocathode gun for the electron source. Based on operational experience at SLAC's GTF and SDL and ATF at BNL as well as other laboratories, the 1.6cell s-band (2856MHz) gun was chosen to be the best electron source for the LCLS, however a significant redesign was necessary to achieve the challenging parameters. Detailed 3-D analysis and design was used to produce near-perfect rotationally symmetric rf fields to achieve the emittance requirement. In addition, the thermo-mechanical design allows the gun to operate at 120Hz and a 140MV/m cathode field, or to an average power dissipation of 4kW. Both average and pulsed heating issues are addressed in the LCLS gun design. The first LCLS gun is now fabricated and has been operated with high-power RF. The results of these high-power tests are presented and discussed

Status report on the alignment activities at SLAC

International Nuclear Information System (INIS)

Le Cocq, Catherine; Fuss, Brian; Ruland, Robert

2003-01-01

This report mainly focuses on the Alignment Engineering Group, which deals with all aspects of activities involving surveying and alignment at SLAC (Stanford Linear Accelerator Center). These activities are field work, ongoing studies and mapping effort. The majority of fieldwork at SLAC is initiated by the various current physics experiments. As PEP-II switched into operational mode, another major project was fully ramping up: SPEAR. The Stanford Synchrotron Radiation Laboratory (SSRL) had been preparing the upgrade SPEAR3 (3 GeV, 200 mA). Currently the effort has been to remap the entire SPEAR2 ring including existing magnets but also to map and tie in the connected booster ring. Laser trackers, total stations, and digital levels were used and substantial post processing was necessary to tie everything together. In parallel with field works, several instrumentation studies are in progress on laser tracker and total station, leveling instrumentation and gyro theodolites. Further enhancements have been included in the core network analysis package used at SLAC (LEGO). To keep up with the new installation, SLAC is undergoing an update of its site map. Overall this is a very interesting and dynamic time at SLAC, which celebrated its 40th anniversary on October 2nd 2002. (Y. Tanaka)

6D Phase Space Measurements at the SLAC Gun Test Facility

CERN Document Server

Schmerge, J

2003-01-01

Proposed fourth generation light sources using SASE FELs to generate short pulse, coherent X-rays require demonstration of high brightness electron sources. The Gun Test Facility (GTF) at SLAC was built to test high brightness sources for the proposed Linac Coherent Light Source at SLAC. The GTF is composed of an Sband photocathode rf gun with a Cu cathode, emittance compensating solenoid, single 3 m SLAC linac section and e-beam diagnostic section with a UV drive laser system. The longitudinal emittance exiting the gun has been determined by measuring the energy spectrum downstream of the linac as a function of the linac phase. The e-beam pulse width, correlated and uncorrelated energy spread at the linac entrance have been fit to the measured energy spectra using a least square error fitting routine. The fit yields a pulse width of 2.9 ps FWHM for a 4.3 ps FWHM laser pulse width and 2% rms correlated energy spread with 0.07% rms uncorrelated energy spread. The correlated energy spread is enhanced in the lin...

Wakefields in SLAC linac collimators

Directory of Open Access Journals (Sweden)

A. Novokhatski

2014-12-01

Full Text Available When a beam travels near collimator jaws, it gets an energy loss and a transverse kick due to the backreaction of the beam field diffracted from the jaws. The effect becomes very important for an intense short bunch when a tight collimation of the background beam halo is required. In the Linac Coherent Light Source at SLAC a collimation system is used to protect the undulators from radiation due to particles in the beam halo. The halo is most likely formed from gun dark current or dark current in some of the accelerating sections. However, collimators are also responsible for the generation of wake fields. The wake field effect from the collimators not only brings an additional energy jitter and change in the trajectory of the beam, but it also rotates the beam on the phase plane, which consequently leads to a degradation of the performance of the Free Electron Laser at the Linac Coherent Light Source. In this paper, we describe a model of the wake field radiation in the SLAC linac collimators. We use the results of a numerical simulation to illustrate the model. Based on the model, we derive simple formulas for the bunch energy loss and the average kick. We also present results from experimental measurements that confirm our model.

Recent Upgrade of the Klystron Modulator at SLAC

International Nuclear Information System (INIS)

Nguyen, M.N.; Burkhart, C.P.; Lam, B.K.; Morris, B.

2011-01-01

The SLAC National Accelerator Laboratory employs 244 klystron modulators on its two-mile-long linear accelerator that has been operational since the early days of the SLAC establishment in the sixties. Each of these original modulators was designed to provide 250 kV, 262 A and 3.5 μS at up to 360 pps using an inductance-capacitance resonant charging system, a modified type-E pulse-forming network (PFN), and a pulse transformer. The modulator internal control comprised of large step-start resistor-contactors, vacuum-tube amplifiers, and 120 Vac relays for logical signals. A major, power-component-only upgrade, which began in 1983 to accommodate the required beam energy of the SLAC Linear Collider (SLC) project, raised the modulator peak output capacity to 360 kV, 420 A and 5.0 μS at a reduced pulse repetition rate of 120 pps. In an effort to improve safety, performance, reliability and maintainability of the modulator, this recent upgrade focuses on the remaining three-phase AC power input and modulator controls. The upgrade includes the utilization of primary SCR phase control rectifiers, integrated fault protection and voltage regulation circuitries, and programmable logic controllers (PLC) -- with an emphasis on component physical layouts for safety and maintainability concerns. In this paper, we will describe the design and implementation of each upgraded component in the modulator control system. We will also report the testing and present status of the modified modulators.

12 CFR 567.2 - Minimum regulatory capital requirement.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Minimum regulatory capital requirement. 567.2... Regulatory Capital Requirements § 567.2 Minimum regulatory capital requirement. (a) To meet its regulatory capital requirement a savings association must satisfy each of the following capital standards: (1) Risk...

Gallium arsenide digital integrated circuits for controlling SLAC CW-RF systems

International Nuclear Information System (INIS)

Ronan, M.T.; Lee, K.L.; Corredoura, P.; Judkins, J.G.

1989-01-01

In order to fill the PEP and SPEAR storage rings with beams from the SLC linac and damping rings, precise control of the linac subharmonic buncher and the damping ring RF is required. Recently several companies have developed resettable GaAs master/slave D-type flip-flops which are capable of operating at frequencies of 3 GHz and higher. Using these digital devices as frequency dividers, one can phase shift the SLAC CW-RF systems to optimize the timing for filling the storage rings. The authors have evaluated the performance of integrated circuits from two vendors for our particular application. Using microstrip circuit techniques, they have built and operated in the accelerator several chassis to synchronize a reset signal from the storage rings to the SLAC 2.856 GHz RF and to phase shift divide-by-four and divide-by-sixteen frequency dividers to the nearest 350 psec bucket required for filling

Gallium arsenide digital integrated circuits for controlling SLAC CW-RF systems

International Nuclear Information System (INIS)

Ronan, M.T.; Lee, K.L.; Corredoura, P.; Judkins, J.G.

1988-10-01

In order to fill the PEP and SPEAR storage rings with beams from the SLC linac and damping rings, precise control of the linac subharmonic buncher and the damping ring RF is required. Recently several companies have developed resettable GaAs master/slave D-type flip-flops which are capable of operating at frequencies of 3 GHz and higher. Using these digital devices as frequency dividers, one can phase shift the SLAC CW-RF systems to optimize the timing for filling the storage rings. We have evaluated the performance of integrated circuits from two vendors for our particular application. Using microstrip circuit techniques, we have built and operated in the accelerator several chassis to synchronize a reset signal from the storage rings to the SLAC 2.856 GHz RF and to phase shift divide-by-four and divide-by-sixteen frequency dividers to the nearest 350 psec bucket required for filling. 4 refs., 4 figs., 2 tabs

Linear collider research and development at SLAC, LBL and LLNL

International Nuclear Information System (INIS)

Mattison, T.S.

1988-10-01

The study of electron-positron (e + e/sup /minus//) annihilation in storage ring colliders has been very fruitful. It is by now well understood that the optimized cost and size of e + e/sup /minus// storage rings scales as E(sub cm//sup 2/ due to the need to replace energy lost to synchrotron radiation in the ring bending magnets. Linear colliders, using the beams from linear accelerators, evade this scaling law. The study of e/sup +/e/sup /minus// collisions at TeV energy will require linear colliders. The luminosity requirements for a TeV linear collider are set by the physics. Advanced accelerator research and development at SLAC is focused toward a TeV Linear Collider (TLC) of 0.5--1 TeV in the center of mass, with a luminosity of 10/sup 33/--10/sup 34/. The goal is a design for two linacs of less than 3 km each, and requiring less than 100 MW of power each. With a 1 km final focus, the TLC could be fit on Stanford University land (although not entirely within the present SLAC site). The emphasis is on technologies feasible for a proposal to be framed in 1992. Linear collider development work is progressing on three fronts: delivering electrical energy to a beam, delivering a focused high quality beam, and system optimization. Sources of high peak microwave radio frequency (RF) power to drive the high gradient linacs are being developed in collaboration with Lawrence Berkeley Laboratory (LBL) and Lawrence Livermore National Laboratory (LLNL). Beam generation, beam dynamics and final focus work has been done at SLAC and in collaboration with KEK. Both the accelerator physics and the utilization of TeV linear colliders were topics at the 1988 Snowmass Summer Study. 14 refs., 4 figs., 1 tab

An Automated 476 MHz RF Cavity Processing Facility at SLAC

CERN Document Server

McIntosh, P; Schwarz, H

2003-01-01

The 476 MHz accelerating cavities currently used at SLAC are those installed on the PEP-II B-Factory collider accelerator. They are designed to operate at a maximum accelerating voltage of 1 MV and are routinely utilized on PEP-II at voltages up to 750 kV. During the summer of 2003, SPEAR3 will undergo a substantial upgrade, part of which will be to replace the existing 358.54 MHz RF system with essentially a PEP-II high energy ring (HER) RF station operating at 476.3 MHz and 3.2 MV (or 800 kV/cavity). Prior to installation, cavity RF processing is required to prepare them for use. A dedicated high power test facility is employed at SLAC to provide the capability of conditioning each cavity up to the required accelerating voltage. An automated LabVIEW based interface controls and monitors various cavity and test stand parameters, increasing the RF fields accordingly such that stable operation is finally achieved. This paper describes the high power RF cavity processing facility, highlighting the features of t...

The creation of SLAC leading to 30 years of operation

International Nuclear Information System (INIS)

Panofsky, W.K.H.

1996-01-01

The different phases of operation of SLAC which provided the basis of its longevity are outlined. SLAC has been an unusually productive laboratory both in terms of genuinely new revelations and the accumulation of archival data. Current operation of SLAC is divided between fixed target experiments, whose energy has now been extended to 50 GeV, and continued use of the SLC with the SLAC large detector. Because of the availability of polarization, results obtained in the SLC-SLD combination have been competitive with the experiments using LEP at CERN, notwithstanding the significantly larger available luminosities at the much larger LEP machine. In addition the SLC, together with specialized test facilities, constitute a basic laboratory to determine the design of the Next Linear Collider (NLC)

Longitudinal and transverse wake potentials in SLAC

International Nuclear Information System (INIS)

Bane, K.; Wilson, P.

1980-01-01

In a machine with short bunches of high peak currents, such as the SLAC collider, one needs to know the longitudinal wake potential, for the higher mode losses, and the transverse wake potential, since, for bunches passing slightly off axis, the induced transverse forces will tend to cause beam break up. The longitudinal and transverse wakes of the SLAC structure presented here, were calculated by computer using the modal method, and including an analytic extension for higher modes. (Auth.)

BABAR - the detector for the PEP II B Factory at SLAC

International Nuclear Information System (INIS)

Lueth, V.

1994-09-01

BABAR refers to the detector that is being designed for the PEP II B-Factory at SLAC to perform a comprehensive study of CP violation in B meson decays. The design requirements and the principal detector components are briefly described. A summary of the expected physics performance is presented

Computer control of rf at SLAC

International Nuclear Information System (INIS)

Schwarz, H.D.

1985-03-01

The Stanford Linear Accelerator is presently upgraded for the SLAC Linear Collider project. The energy is to be increased from approximately 31 GeV to 50 GeV. Two electron beams and one positron beam are to be accelerated with high demands on the quality of the beams. The beam specifications are shown. To meet these specifications, all parameters influencing the beams have to be under tight control and continuous surveillance. This task is accomplished by a new computer system implemented at SLAC which has, among many other functions, control over rf accelerating fields. 13 refs., 8 figs., 2 tabs

The SLAC NLC source program

International Nuclear Information System (INIS)

Caryotakis, G.

1995-01-01

The SLAC approach to a future e + e - 1-TeV linear collider, which will probably be an internationally sponsored project at the turn of the century, is a conventional 14-kilometer accelerator operating at 11.4 GHz. SLAC is on the 6th year of a program to develop 50--100 MW klystron sources for the ''Next Linear Collider'' or ''NLC''. The paper traces the development of these tubes and presents experimental results for solenoid-focused klystrons with output circuits of both the standing-wave and traveling-wave variety. In addition, the design of a periodically-focused permanent magnet klystron is discussed and a tape is shown with time-sequenced simulations of the interaction process for such a tube

Grand Gulf-prioritization of regulatory requirements

International Nuclear Information System (INIS)

Meisner, M.J.

1993-01-01

As cost pressures mount, Grand Gulf nuclear station (GGNS) is relying increasingly on various prioritization approaches to implement, modify, eliminate, or defer regulatory requirements. Regulatory requirements can be prioritized through the use of three measures: (1) safety (or risk) significance; (2) cost; and (3) public policy (or political) significance. This paper summarizes GGNS' efforts to implement solutions to regulatory issues using these three prioritization schemes to preserve a balance between cost and safety benefit

Operational experience with SLAC's beam containment electronics

International Nuclear Information System (INIS)

Constant, T.N.; Crook, K.; Heggie, D.

1977-03-01

Considerable operating experience was accumulated at SLAC with an extensive electronic system for the containment of high power accelerated beams. Average beam power at SLAC can approach 900 kilowatts with the potential for burning through beam stoppers, protection collimators, and other power absorbers within a few seconds. Fast, reliable, and redundant electronic monitoring circuits have been employed to provide some of the safeguards necessary for minimizing the risk to personnel. The electronic systems are described, and the design philosophy and operating experience are discussed

SLAC workshop on high energy electroproduction and spin physics

International Nuclear Information System (INIS)

1992-01-01

These Proceedings contain copies of the transparencies presented at the Workshop on High Energy Electroproduction and Spin Physics held at SLAC on February 5--8, 1992. The purpose of this Workshop was to bring people together to discuss the possibilities for new experiments using the SLAC high intensity electron and photon beams and the facilities of End Station A

Transport of LCLS-II 1.3 Ghz cryomodule to SLAC

Energy Technology Data Exchange (ETDEWEB)

McGee, M. W.; Arkan, T.; Peterson, T.; Tang, Z.; Boo, S.; Carrasco, M.; Daly, E.; Huque, N.

2016-06-30

In a partnership with SLAC National Accelerator Laboratory (SLAC) and Jefferson Lab, Fermilab will assemble and test 17 of the 35 total 1.3 GHz cryomodules for the Linac Coherent Light Source II (LCLS-II) Project. These include a prototype built and delivered by each Lab. Another two 3.9 GHz cryomodules will be built, tested and transported by Fermilab to SLAC. Each assembly will be transported over-the-road from Fermilab or Jefferson Lab using specific routes to SLAC. The transport system consists of a base frame, isolation fixture and upper protective truss. The strongback cryomodule lifting fixture is described along with other supporting equipment used for both over-the-road transport and local (on-site) transport at Fermilab. Initially, analysis of fragile components and stability studies will be performed in order to assess the risk associated with over-the-road transport of a fully assembled cryomodule.

The SLAC linear collider

International Nuclear Information System (INIS)

Richter, B.

1985-01-01

A report is given on the goals and progress of the SLAC Linear Collider. The author discusses the status of the machine and the detectors and give an overview of the physics which can be done at this new facility. He also gives some ideas on how (and why) large linear colliders of the future should be built

Microprocessors in physics experiments at SLAC

International Nuclear Information System (INIS)

Rochester, L.S.

1981-01-01

The increasing size and complexity of high energy physics experiments is changing the way data are collected. To implement a trigger or event filter requires complex logic which may have to be modified as the experiment proceeds. Simply to monitor a detector, large amounts of data must be processed online. The use of microprocessors or other programmable devices can help to achieve these ends flexibly and economically. At SLAC, a number of microprocessor-based systems have been built and are in use in experimental setups, and others are now being developed. This talk is a review of existing systems and their use in experiments, and of developments in progress and future plans. (orig.)

Microprocessors in physics experiments at SLAC

International Nuclear Information System (INIS)

Rochester, L.S.

1981-04-01

The increasing size and complexity of high energy physics experiments is changing the way data are collected. To implement a trigger or event filter requires complex logic which may have to be modified as the experiment proceeds. Simply to monitor a detector, large amounts of data must be processed on line. The use of microprocessors or other programmable devices can help to achieve these ends flexibly and economically. At SLAC, a number of microprocessor-based systems have been built and are in use in experimental setups, and others are now being developed. This talk is a review of existing systems and their use in experiments, and of developments in progress and future plans

Sleepless at SLAC

Energy Technology Data Exchange (ETDEWEB)

Dement, William (Stanford Sleep Disorders Center)

2006-01-23

Feeling tired? More than 30 million Americans suffer from sleep disorders. Nevertheless, as a society we remain largely ignorant of the significance of sleep in determining the quality of our waking lives. Dr. William Dement, Stanford Professor and one of the world's foremost experts on sleep and sleep deprivation, joins SLAC's Colloquium Series to present exciting new findings in the field of sleep research. You'll never sleep the same again!

SLAC Scanner Processor: a FASTBUS module for data collection and processing

International Nuclear Information System (INIS)

Brafman, H.; Glanzman, T.; Lankford, A.J.; Olsen, J.; Paffrath, L.

1984-10-01

A new, general purpose, programmable FASTBUS module, the SLAC Scanner Processor (SSP), is introduced. Both hardware and software elements of SSP operation are discussed. The role of the SSP within the upgraded Mark II Detector at SLAC is described

A possible CO2 conducting and concentrating mechanism in plant stomata SLAC1 channel.

Directory of Open Access Journals (Sweden)

Qi-Shi Du

Full Text Available BACKGROUND: The plant SLAC1 is a slow anion channel in the membrane of stomatal guard cells, which controls the turgor pressure in the aperture-defining guard cells, thereby regulating the exchange of water vapour and photosynthetic gases in response to environmental signals such as drought, high levels of carbon dioxide, and bacterial invasion. Recent study demonstrated that bicarbonate is a small-molecule activator of SLAC1. Higher CO(2 and HCO(3(- concentration activates S-type anion channel currents in wild-type Arabidopsis guard cells. Based on the SLAC1 structure a theoretical model is derived to illustrate the activation of bicarbonate to SLAC1 channel. Meanwhile a possible CO(2 conducting and concentrating mechanism of the SLAC1 is proposed. METHODOLOGY: The homology structure of Arabidopsis thaliana SLAC1 (AtSLAC1 provides the structural basis for study of the conducting and concentrating mechanism of carbon dioxide in SLAC1 channels. The pK(a values of ionizable amino acid side chains in AtSLAC1 are calculated using software PROPKA3.0, and the concentration of CO(2 and anion HCO(3(- are computed based on the chemical equilibrium theory. CONCLUSIONS: The AtSLAC1 is modeled as a five-region channel with different pH values. The top and bottom layers of channel are the alkaline residue-dominated regions, and in the middle of channel there is the acidic region surrounding acidic residues His332. The CO(2 concentration is enhanced around 10(4 times by the pH difference between these regions, and CO(2 is stored in the hydrophobic region, which is a CO(2 pool. The pH driven CO(2 conduction from outside to inside balances the back electromotive force and maintain the influx of anions (e.g. Cl(- and NO(3(- from inside to outside. SLAC1 may be a pathway providing CO(2 for photosynthesis in the guard cells.

SLAC accelerator operations report: 1995--1997

International Nuclear Information System (INIS)

Erickson, R.; Allen, C.W.; Anderson, S.; Linebarger, W.; Stanek, M.

1997-05-01

Operational statistics for the linear accelerator programs at SLAC are presented, including run-time records for SLC and the fixed-target programs. Also included are summaries of reliability and maintenance-related statistics

Binary rf pulse compression experiment at SLAC

International Nuclear Information System (INIS)

Lavine, T.L.; Spalek, G.; Farkas, Z.D.; Menegat, A.; Miller, R.H.; Nantista, C.; Wilson, P.B.

1990-06-01

Using rf pulse compression it will be possible to boost the 50- to 100-MW output expected from high-power microwave tubes operating in the 10- to 20-GHz frequency range, to the 300- to 1000-MW level required by the next generation of high-gradient linacs for linear for linear colliders. A high-power X-band three-stage binary rf pulse compressor has been implemented and operated at the Stanford Linear Accelerator Center (SLAC). In each of three successive stages, the rf pulse-length is compressed by half, and the peak power is approximately doubled. The experimental results presented here have been obtained at low-power (1-kW) and high-power (15-MW) input levels in initial testing with a TWT and a klystron. Rf pulses initially 770 nsec long have been compressed to 60 nsec. Peak power gains of 1.8 per stage, and 5.5 for three stages, have been measured. This corresponds to a peak power compression efficiency of about 90% per stage, or about 70% for three stages, consistent with the individual component losses. The principle of operation of a binary pulse compressor (BPC) is described in detail elsewhere. We recently have implemented and operated at SLAC a high-power (high-vacuum) three-stage X-band BPC. First results from the high-power three-stage BPC experiment are reported here

Physics results with polarized electrons at SLAC

International Nuclear Information System (INIS)

Prescott, C.Y.

1996-03-01

Polarized electron beams can play an important role in the dynamics of interactions at high energies. Polarized electron beams at SLAC have been an important part of the physics program since 1970, when they were first proposed for use in testing the spin structure of the proton. Since 1992, the SLAC linear accelerator and the SLC have operated solely with polarized electrons, providing data for tests of QCD in studies of the spin structure of the nucleon and tests of the electroweak sector of the Standard Model. In the following sections, the performance of the source is summarized, and some of the recent results using the polarized beams are discussed

SLAC R and D toward a TeV Linear Collider

International Nuclear Information System (INIS)

Wilson, P.B.

1988-10-01

At CERN, KEK, Novosibirsk and SLAC, serious thought is being given to the design of linear colliders in the 0.5--2.0 TeV center-of-mass energy range. This paper reviews current progress at SLAC toward the design of such a collider. No attempt is made here to summarize ongoing work at the other laboratories. However, research on linear colliders is clearly an international effort, and success at SLAC will be greatly expedited by communication and cooperation with other laboratories in the US and abroad. In addition to major programs at the laboratories mentioned above, contributions relevant to linear collider design are being made at DESY, LAL (Orsay), LBL, LLNL and elsewhere. 49 refs., 6 tabs

Development of the Virtual Visitor Center at SLAC

Energy Technology Data Exchange (ETDEWEB)

McDunn, Ruth

1999-11-17

The Virtual Visitor Center (VVC) web site (www2.slac.stanford.edu/vvc) is a ''virtual'' version of the Visitor Center, a mini science museum that opened at SLAC in 1996. The VVC was made public in December 1998. Both centers contribute to SLAC mission regarding education of the next generation and increasing scientific awareness of the public. The site is designed to mimic the real visitor center and allow a larger audience to the information. The intent was to reach the 8th-12th grade audience. Considerable effort was made to organize the content, including color-coding graphical elements for each main topic area. Tables of contents, a search tool, several photo tours, as well as graphical and non-graphical menu bars allow users many methods of navigating the site. The site was developed over almost two years using an estimated .95 FTE, split between a program manager, graphic designer, content provider (theoretical physicist), and a summer intern (high school teacher). As of November 1999, the site consists of 1,147 files, 935 images, 3,080 internal hyperlinks, and 190 external hyperlinks. The site has had over 1 million hits between January and mid-October 1999 and averages about 600 page views each day. Future plans include bringing the web site into compliance with the W3Cs Web Content Accessibility guidelines, thoroughly integrating the glossary terms, continued incorporation of current research at SLAC, and adding more interactivity.

Development of the Virtual Visitor Center at SLAC

International Nuclear Information System (INIS)

McDunn, Ruth

1999-01-01

The Virtual Visitor Center (VVC) web site (www2.slac.stanford.edu/vvc) is a ''virtual'' version of the Visitor Center, a mini science museum that opened at SLAC in 1996. The VVC was made public in December 1998. Both centers contribute to SLAC mission regarding education of the next generation and increasing scientific awareness of the public. The site is designed to mimic the real visitor center and allow a larger audience to the information. The intent was to reach the 8th-12th grade audience. Considerable effort was made to organize the content, including color-coding graphical elements for each main topic area. Tables of contents, a search tool, several photo tours, as well as graphical and non-graphical menu bars allow users many methods of navigating the site. The site was developed over almost two years using an estimated .95 FTE, split between a program manager, graphic designer, content provider (theoretical physicist), and a summer intern (high school teacher). As of November 1999, the site consists of 1,147 files, 935 images, 3,080 internal hyperlinks, and 190 external hyperlinks. The site has had over 1 million hits between January and mid-October 1999 and averages about 600 page views each day. Future plans include bringing the web site into compliance with the W3Cs Web Content Accessibility guidelines, thoroughly integrating the glossary terms, continued incorporation of current research at SLAC, and adding more interactivity

Pulse modulator developments in support of klystron testing at SLAC

International Nuclear Information System (INIS)

Koontz, R.F.; Cassel, R.; Lamare, J. de; Ficklin, D.; Gold, S.; Harris, K.

1993-01-01

Several families of high power klystrons in S- and X-Band are being developed in the Klystron Laboratory at SLAC. To support these developments, a number of new pulse modulators are being designed from scratch, or upgraded from existing laboratory test modulators. This paper outlines the modulator parameters available in the SLAC Klystron Laboratory, and discuss two new modulators that are under construction

Review of trigger and on-line processors at SLAC

International Nuclear Information System (INIS)

Lankford, A.J.

1984-07-01

The role of trigger and on-line processors in reducing data rates to manageable proportions in e + e - physics experiments is defined not by high physics or background rates, but by the large event sizes of the general-purpose detectors employed. The rate of e + e - annihilation is low, and backgrounds are not high; yet the number of physics processes which can be studied is vast and varied. This paper begins by briefly describing the role of trigger processors in the e + e - context. The usual flow of the trigger decision process is illustrated with selected examples of SLAC trigger processing. The features are mentioned of triggering at the SLC and the trigger processing plans of the two SLC detectors: The Mark II and the SLD. The most common on-line processors at SLAC, the BADC, the SLAC Scanner Processor, the SLAC FASTBUS Controller, and the VAX CAMAC Channel, are discussed. Uses of the 168/E, 3081/E, and FASTBUS VAX processors are mentioned. The manner in which these processors are interfaced and the function they serve on line is described. Finally, the accelerator control system for the SLC is outlined. This paper is a survey in nature, and hence, relies heavily upon references to previous publications for detailed description of work mentioned here. 27 references, 9 figures, 1 table

SLAC B Factory computing

International Nuclear Information System (INIS)

Kunz, P.F.

1992-02-01

As part of the research and development program in preparation for a possible B Factory at SLAC, a group has been studying various aspects of HEP computing. In particular, the group is investigating the use of UNIX for all computing, from data acquisition, through analysis, and word processing. A summary of some of the results of this study will be given, along with some personal opinions on these topics

Regulatory requirements related to maintenance and compliance monitoring

International Nuclear Information System (INIS)

Ling, A.K.H.

1997-01-01

The maintenance related regulatory requirements are identified in the regulatory documents and licence conditions. Licensee complies with these requirements by operating the nuclear power plant within the safe operating envelope as given in the operating policies and principles and do maintenance according to approved procedures and/or work plans. Safety systems are regularly tested. AECB project officers review and check to ensure that the licensee operates the nuclear power plant in accordance with the regulatory requirements and licence conditions. (author). 6 tabs

The SLAC lasertron project

International Nuclear Information System (INIS)

Sinclair, C.K.

1986-10-01

SLAC has a program underway to develop an efficient high power microwave source for accelerator applications employing a photoemission cathode, the so-called lasertron. After a brief discussion of the lasertron idea, the various elements of the current program are reviewed. A proof-of-principle experiment to build a 35 MW, 70% efficiency, S-band microwave source is nearing completion. Actual RF power testing is expected to begin in late 1986 or early 1987

The SLAC polarized electron source

International Nuclear Information System (INIS)

Clendenin, J.E.; Alley, R.; Frisch, J.; Kotseroglou, T.; Mulhollan, G.; Schultz, D.; Tang, H.; Turner, J.; Yeremian, A.D.

1997-08-01

Since 1992, the SLAC 3-km linac has operated exclusively with polarized electrons. The polarized electron source is highly reliable, remotely operated and monitored, and able to produce a variety of electron bunch profiles for high-energy physics experiments. The source and its operating characteristics are described. Some implications drawn from the operating experience are discussed

Latest Results in SLAC 75-MW PPM Klystrons

International Nuclear Information System (INIS)

Sprehn, D.; Caryotakis, G.; Haase, A.; Jongewaard, E.; Laurent, L.; Pearson, C.; Phillips, R.

2006-01-01

75 MW X-band klystrons utilizing Periodic Permanent Magnet (PPM) focusing have been undergoing design, fabrication and testing at the Stanford Linear Accelerator Center (SLAC) for almost nine years. The klystron development has been geared toward realizing the necessary components for the construction of the Next Linear Collider (NLC). The PPM devices built to date which fit this class of operation consist of a variety of 50 MW and 75 MW devices constructed by SLAC, KEK (Tsukuba, Japan) and industry. All these tubes follow from the successful SLAC design of a 50 MW PPM klystron in 1996. In 2004 the latest two klystrons were constructed and tested with preliminary results reported at EPAC2004. The first of these two devices was tested to the full NLC specifications of 75 MW, 1.6 microseconds pulse length, and 120 Hz. This 14.4 kW average power operation came with a tube efficiency >50%. The most recent testing of these last two devices will be presented here. Design and manufacturing issues of the latest klystron, due to be tested by the Fall of 2005, are also discussed

Review of the SLAC and Les Houches workshops

International Nuclear Information System (INIS)

Prescott, C.Y.

1994-12-01

Polarized Electron Source workshops have been held at varying intervals, beginning in 1983 when Charles Sinclair convened the first at SLAC. Since that time, three workshops were held in conjunction with the International Spin Symposia and two at other occasions. The increasing importance of polarized electron beams at accelerators has stimulated interest in these workshops. Two workshops have been held since the last International Spin Symposium in Nagoya. In 1993, a workshop was held at SLAC, and in 1994 at Les Houches, a polarized electron beam session was held as part of a polarized beam and targets workshop. This report summarizes highlights from the latter two workshops

SLAC accelerator operations report: 1992-1995

International Nuclear Information System (INIS)

Erickson, R.; Allen, C.W.; Inman, T.K.; Linebarger, W.; Stanek, M.

1995-05-01

Operational statistics for the linear accelerator programs at SLAC are presented, including run-time records for the SLC, FFTB, and fixed target programs. Also included are summaries of reliability and maintenance-related statistics and a discussion of the analysis tools used to study error messages generated by the control system

Homologue Structure of the SLAC1 Anion Channel for Closing Stomata in Leaves

Energy Technology Data Exchange (ETDEWEB)

Y Chen; L Hu; M Punta; R Bruni; B Hillerich; B Kloss; B Rost; J Love; S Siegelbaum; W Hendrickson

2011-12-31

The plant SLAC1 anion channel controls turgor pressure in the aperture-defining guard cells of plant stomata, thereby regulating the exchange of water vapour and photosynthetic gases in response to environmental signals such as drought or high levels of carbon dioxide. Here we determine the crystal structure of a bacterial homologue (Haemophilus influenzae) of SLAC1 at 1.20 {angstrom} resolution, and use structure-inspired mutagenesis to analyse the conductance properties of SLAC1 channels. SLAC1 is a symmetrical trimer composed from quasi-symmetrical subunits, each having ten transmembrane helices arranged from helical hairpin pairs to form a central five-helix transmembrane pore that is gated by an extremely conserved phenylalanine residue. Conformational features indicate a mechanism for control of gating by kinase activation, and electrostatic features of the pore coupled with electrophysiological characteristics indicate that selectivity among different anions is largely a function of the energetic cost of ion dehydration.

Luminosity enhancements at SLAC

International Nuclear Information System (INIS)

Coward, D.H.

1984-04-01

Several ideas are discussed that have been proposed to improve the luminosity at the SPEAR and PEP electron-positron storage rings and to insure good luminosity at the SLAC Linear Collider. There have been two proposals studied recently for SPEAR: a Microbeta insertion using Samarium Cobalt permanent magnets, and a Minibeta insertion using conventional quadrupole magnets. The notations Microbeta and minibeta used here are somewhat arbitrary since the front faces of the first quadrupole magnets for both insertions are at nearly the same distance from the interaction point

24 CFR 266.505 - Regulatory agreement requirements.

Science.gov (United States)

2010-04-01

... force for the duration of the insured mortgage and note or bond. The Regulatory Agreement must include a... Project Management and Servicing § 266.505 Regulatory agreement requirements. (a) General. (1) The HFA... payments due under the mortgage and note/bond. (2) Where necessary, establish a sinking fund for future...

SLAC Linac Preparations for FACET

International Nuclear Information System (INIS)

Erickson, Roger

2011-01-01

The SLAC 3km linear electron accelerator has been cut at the two-thirds point to provide beams to two independent programs. The last third provides the electron beam for the Linac Coherent Light Source (LCLS), leaving the first two-thirds available for FACET, the new experimental facility for accelerator science and test beams. In this paper, we describe this separation and projects to prepare the linac for the FACET experimental program.

Status of the SLAC Linear Collider Project

International Nuclear Information System (INIS)

Stiening, R.

1983-01-01

The SLAC Linear Collider Project has two principal goals. The first is to serve as a prototype for a future very high energy linear electron-positron collider. The second is to quickly, at low cost, achieve sufficient luminosity at 100 GeV center-of-mass energy to explore the physics of the Z 0 . The first goal is important to the future of electron-positron physics because the rapid increase of synchrotron radiation with energy causes the cost of circular storage ring colliders to whereas the cost of linear colliders increases only in proportion to the center-of-mass energy. The second is important because the existance at SLAC of a linear accelerator which can be converted at low cost to collider operation makes possible a unique opportunity to quickly achieve 100 GeV center-of-mass collisions. At the design luminosity of 6.0 x 10 30 many thousands of Z 0 decays should be observed in each day of operation

GLAST beam test at SLAC

International Nuclear Information System (INIS)

Engovatov, D.; Anthony, P.; Atwood, W.

1996-10-01

In May and June, a beam test for GLAST calorimeter technologies was conducted. A parasitic low intensity electron/tagged photon beam line into the End Station A at SLAC was commissioned and used. The preliminary stage of the test was devoted to measuring the performance of the parasitic beam. In the main test we studied the response of GLAST prototype CsI and scintillating fiber calorimeters to the electrons and photons. Results of this work are discussed

Molecular Evolution of Slow and Quick Anion Channels (SLACs and QUACs/ALMTs).

Science.gov (United States)

Dreyer, Ingo; Gomez-Porras, Judith Lucia; Riaño-Pachón, Diego Mauricio; Hedrich, Rainer; Geiger, Dietmar

2012-01-01

Electrophysiological analyses conducted about 25 years ago detected two types of anion channels in the plasma membrane of guard cells. One type of channel responds slowly to changes in membrane voltage while the other responds quickly. Consequently, they were named SLAC, for SLow Anion Channel, and QUAC, for QUick Anion Channel. Recently, genes SLAC1 and QUAC1/ALMT12, underlying the two different anion current components, could be identified in the model plant Arabidopsis thaliana. Expression of the gene products in Xenopus oocytes confirmed the quick and slow current kinetics. In this study we provide an overview on our current knowledge on slow and quick anion channels in plants and analyze the molecular evolution of ALMT/QUAC-like and SLAC-like channels. We discovered fingerprints that allow screening databases for these channel types and were able to identify 192 (177 non-redundant) SLAC-like and 422 (402 non-redundant) ALMT/QUAC-like proteins in the fully sequenced genomes of 32 plant species. Phylogenetic analyses provided new insights into the molecular evolution of these channel types. We also combined sequence alignment and clustering with predictions of protein features, leading to the identification of known conserved phosphorylation sites in SLAC1-like channels along with potential sites that have not been yet experimentally confirmed. Using a similar strategy to analyze the hydropathicity of ALMT/QUAC-like channels, we propose a modified topology with additional transmembrane regions that integrates structure and function of these membrane proteins. Our results suggest that cross-referencing phylogenetic analyses with position-specific protein properties and functional data could be a very powerful tool for genome research approaches in general.

Molecular evolution of slow and quick anion channels (SLACs and QUACs/ALMTs

Directory of Open Access Journals (Sweden)

Ingo eDreyer

2012-11-01

Full Text Available Electrophysiological analyses conducted about 25 years ago detected two types of anion channels in the plasma membrane of guard cells. One type of channel responds slowly to changes in membrane voltage while the other responds quickly. Consequently, they were named SLAC, for SLow Anion Channel, and QUAC, for QUick Anion Channel. Recently, genes SLAC1 and QUAC1/ALMT12, underlying the two different anion current components, could be identified in the model plant Arabidopsis thaliana. Expression of the gene products in Xenopus oocytes confirmed the quick and slow current kinetics. In this study we provide an overview on our current knowledge on slow and quick anion channels in plants and analyze the molecular evolution of ALMT/QUAC-like and SLAC-like channels. We discovered fingerprints that allow screening databases for these channel types and were able to identify 192 (177 non-redundant SLAC-like and 422 (402 non-redundant ALMT/QUAC-like proteins in the fully sequenced genomes of 32 plant species. Phylogenetic analyses provided new insights into the molecular evolution of these channel types. We also combined sequence alignment and clustering with predictions of protein features, leading to the identification of known conserved phosphorylation sites in SLAC1-like channels along with potential sites that have not been yet experimentally confirmed. Using a similar strategy to analyze the hydropathicity of ALMT/QUAC-like channels, we propose a modified topology with additional transmembrane regions that integrates structure and function of these membrane proteins. Our results suggest that cross-referencing phylogenetic analyses with position-specific protein properties and functional data could be a very powerful tool for genome research approaches in general.

Proceedings of the SLAC/KEK ATF lattice workshop

International Nuclear Information System (INIS)

Urakawa, Junji

1993-04-01

The SLAC/KEK ATF Lattice Workshop was held on December 8-11, 1992 at KEK, National Laboratory for High Energy Physics. The purpose of this workshop is to critically review the ATF lattice design for any possible improvements, and also to bring SLAC colleagues up to date on recent progress at KEK. At KEK studies on intense multi-bunch beam acceleration and emittance reduction have been actively pursued, evolving into the ATF project since 1990. In 1991 we have launched a large scale reconstruction of the experimental hall. This is to build the shielded housing for the 1.54 GeV injector linac and the test damping ring. Our plan is to begin construction of the linac in March 1993. Some results from the discussions during the Workshop have been already incorporated in the revised ATF lattice design. (J.P.N.)

Multi-Device Knob Utility for LCLS at SLAC

International Nuclear Information System (INIS)

Zelazny, Michael

2009-01-01

At the SLAC National Accelerator Laboratory (SLAC) the Controls Department (CD) has developed a new Multi-Device Knob Utility (MKB) based on the Experimental Physics and Industrial Control System (EPICS) toolkit for controlling one or more Process Variables (PVs) in unison, or simultaneously, from a physical knob located in the control room, or from various software tools such as the EPICS Extensible Display Manager (EDM) or a Swing slider in Java. A group of devices are hooked up to a knob, and then the value written to the devices is a simple function of the value of the knob. This is used, most commonly, to create a bump in the electron beam for the Linac Coherent Light Source (LCLS). Control system variables typically controlled are magnetic fields, phases, and timing offsets. This paper describes the technologies used to implement this utility.

RF pulse compression in the NLC test accelerator at SLAC

International Nuclear Information System (INIS)

Lavine, T.L.

1995-01-01

At the Stanford Linear Accelerator Center (SLAC), the authors are designing a Next Linear Collider (NLC) with linacs powered by X-band klystrons with rf pulse compression. The design of the linac rf system is based on X-band prototypes which have been tested at high power, and on a systems-integration test - the Next Linear Collider Test Accelerator (NLCTA) - which is currently under construction at SLAC. This paper discusses some of the systems implications of rf pulse compression, and the use of pulse compression in the NLCTA, both for peak power multiplication and for controlling, by rf phase modulation, intra-pulse variations in the linac beam energy

Review of regulatory requirements for digital I and C systems

Energy Technology Data Exchange (ETDEWEB)

Kwon, Kee Choon; Lee, Cheol Kwon; Lee, Jang Soo [and others

2001-11-01

This work analyzed and summarized systematically various regulatory requirements that are necessary to develop digital nuclear instrumentation and control (I and C) systems, especially safety systems. The requirements are categorized into system, hardware, software, and quality assurance aspects. This report provides the explanations of terms and abbreviations to help readers understand. Furthermore, appendices of this report summarize the code and standards corresponding to each principal regulatory requirement. The hierarchical structure of regulatory requirements has Nuclear Energy Laws, Enforcement Regulations of Nuclear Energy Laws, and Notifications of Ministry of Science and Technology as utmost level requirements [In case of the US, 10 CFR 50 Appendix A, 10 CFR 50 Appendix B, 10 CFR 50.55a(h), 10 CFR 50.49, etc.]. The requirements include the Draft Regulatory Guidelines for Digital I and C Systems [In case of the US, Standard Review Plan (NUREG-0800), Regulatory Guide, Branch Technical Position (BTP)], KEPIC as standards [In case of the US, IEEE Standards, IEC Standards, ISA, Military Standard, etc.], and various reports issued by Korea Institute of Nuclear Safety [In case of the US, NUREG reports, EPRI reports, etc.]. This report can be referred for the development of safety grade control equipment, plant protection system, and engineered safety feature actuation system.

Review of regulatory requirements for digital I and C systems

International Nuclear Information System (INIS)

Kwon, Kee Choon; Lee, Cheol Kwon; Lee, Jang Soo

2001-11-01

This work analyzed and summarized systematically various regulatory requirements that are necessary to develop digital nuclear instrumentation and control (I and C) systems, especially safety systems. The requirements are categorized into system, hardware, software, and quality assurance aspects. This report provides the explanations of terms and abbreviations to help readers understand. Furthermore, appendices of this report summarize the code and standards corresponding to each principal regulatory requirement. The hierarchical structure of regulatory requirements has Nuclear Energy Laws, Enforcement Regulations of Nuclear Energy Laws, and Notifications of Ministry of Science and Technology as utmost level requirements [In case of the US, 10 CFR 50 Appendix A, 10 CFR 50 Appendix B, 10 CFR 50.55a(h), 10 CFR 50.49, etc.]. The requirements include the Draft Regulatory Guidelines for Digital I and C Systems [In case of the US, Standard Review Plan (NUREG-0800), Regulatory Guide, Branch Technical Position (BTP)], KEPIC as standards [In case of the US, IEEE Standards, IEC Standards, ISA, Military Standard, etc.], and various reports issued by Korea Institute of Nuclear Safety [In case of the US, NUREG reports, EPRI reports, etc.]. This report can be referred for the development of safety grade control equipment, plant protection system, and engineered safety feature actuation system

Identification and biochemical analysis of Slac2-c/MyRIP as a Rab27A-, myosin Va/VIIa-, and actin-binding protein.

Science.gov (United States)

Kuroda, Taruho S; Fukuda, Mitsunori

2005-01-01

Slac2-c/MyRIP is a specific Rab27A-binding protein that contains an N-terminal synaptotagmin-like protein (Slp) homology domain (SHD, a newly identified GTP-Rab27A-binding motif), but in contrast to the Slp family proteins, it lacks C-terminal tandem C2 domains. In vitro Slac2-c simultaneously directly interacts with both Rab27A and an actin-based motor protein, myosin Va, via its N-terminal SHD and middle region, respectively, consistent with the fact that the overall structure of Slac2-c is similar to that of Slac2-a/melanophilin, a linker protein between Rab27A and myosin Va in the melanosome transport in melanocytes. Unlike Slac2-a, however, the middle region of Slac2-c interacts with two types of myosins, myosin Va and myosin VIIa. In addition, the most C-terminal part of both Slac2-a and Slac2-c functions as an actin-binding domain: it directly interacts with globular and fibrous actin in vitro, and the actin-binding domain of Slac2-a and Slac2-c colocalizes with actin filaments when it is expressed in living cells (i.e., PC12 cells and mouse melanocytes). In this chapter we describe the methods that have been used to analyze the protein-protein interactions of Slac2-c, specifically with Rab27A, myosin Va/VIIa, and actin.

Regulatory capital requirements and bail in mechanisms

NARCIS (Netherlands)

Joosen, B.P.M.; Haentjens, M.; Wessels, B.

2015-01-01

With the introduction of the Capital Requirements Regulation (CRR) in the European Union, the qualitative requirements for bank regulatory capital have changed. These changes aim at implementing in Europe the Basel III principles for better bank capital that is able to absorb losses of banks,

SLAC physicists develop test for string theory

CERN Multimedia

Yajnik, Juhi

2006-01-01

"Under certain conditions, string theory solves many of the questions wracking the minds of physicists, but until recently it had one major flaw - it could not be tested. SLAC (Stanford Linear Accelerator Center) scientists have found a way to test this revolutionary theory, which posits that there are 10 or 11 dimensions in our universe" (1 page)

Annual Site Environmental Report (ASER 1999)

Energy Technology Data Exchange (ETDEWEB)

Holden, Gene

2000-08-28

In CY99, SLAC operated under the Work Smart Standards (WSS) Set, which are incorporated in SLAC's Management and Operating contract. The WSS Set includes all applicable statutory and regulatory requirements for public and worker safety and environmental protection. The WSS Set also includes a number of industry standards that were found to be necessary to control specific hazards present at SLAC.

RF pulse compression in the NLC test accelerator at SLAC

International Nuclear Information System (INIS)

Lavine, T.L.

1995-01-01

At the Stanford Linear Accelerator Center (SLAC), we are designing a Next Linear Collider (NLC) with linacs powered by X-band klystrons with rf pulse compression. The design of the linac rf system is based on X-band prototypes which have been tested at high power, and on a systems-integration test---the Next Linear Collider Test Accelerator (NLCTA)---which is currently under construction at SLAC. This paper discusses some of the systems implications of rf pulse compression, and the use of pulse compression in the NLCTA, both for peak power multiplication and for controlling, by rf phase modulation, intra-pulse variations in the linac beam energy. copyright 1995 American Institute of Physics

SLAC RF Source Research at X-Band

International Nuclear Information System (INIS)

Sprehn, D.

2003-01-01

X-band klystrons capable of 75 MW and utilizing either solenoidal or Periodic Permanent Magnet (PPM) focusing are undergoing design, fabrication and testing at the Stanford Linear Accelerator Center (SLAC). The klystron development is part of an effort to realize components necessary for the construction of the Next Linear Collider (NLC). SLAC has developed a solenoidal-focused X-band klystron which is currently the workhorse of high power component testing for the NLC. A state-of-the-art modulator will drive eight of these tubes which, in turn, will power an rf distribution system referred to as the ''8-pack'' in order to test these modulators and waveguide components. Eventually, in an interest to save millions of dollars per year in the operational cost of the NLC, these tubes will be replaced by PPM klystrons. The PPM devices built to date which fit this class of operation consist of a variety of 50 MW and 75 MW devices constructed by SLAC, KEK (Tsukuba, Japan ), and industry. These tubes follow from the successful 50 MW PPM design of 1996. Recent testing of this particular tube at wider pulsewidths has reached 50 MW at 55 % efficiency, 2.4 μs and 60 Hz. Two 50 MW PPM klystrons produced by industry have been delivered to SLAC. One of these devices arrived with a vacuum suitable for test. Testing during 2001 revealed a serious, but curious, vacuum response which limited the operation to an rf output of ∼40 MW. A 75 MW PPM klystron prototype was first constructed in 1997 and later modified in 1999 to eliminate oscillations. This tube has reached the NLC design target of 75 MW at 1.5 μs though at a significantly reduced rep rate. Two new 75 MW PPM klystrons were constructed and tested in 2002 after a diode was successfully tested in 2001. The new design was aimed at reducing the cost and increasing the reliability of such high-energy devices. The rf circuit and beam focusing for one of these devices was built by industry and incorporated into one of the tubes

Wide-band cable systems at SLAC

International Nuclear Information System (INIS)

Struven, W.

1983-01-01

SLAC's first cable TV system was installed in 1979 to remotely monitor a narrow pulse which was generated in the west end of the klystron gallery. When Stanford Linear Collider (SLC) experimental work started at the west end of the accelerator, the original 1979 cable was upgraded to a bidirectional system so that 2 MBaud point-to-point data and several video and 9600 baud channels could be transmitted. The implementation of the SLC requires a complete upgrading of the accelerator control system. The system is based on a distributed processing configuration using a PDP11/780 VAX in the Main Control Center (MCC) and Intel single-board computers in a multibus configuration along the accelerator. The high-speed data linking is supplied by a 1 MBaud Time Division Multiple Access (TDMA) Network. The same cable is used to provide video, low-speed data, voice and high-speed point-to-point data services. The transmission system will utilize a wideband midsplit cable facility to collect and distribute signals to all parts of the network

Advocacy for the Archives and History Office of the SLAC National Accelerator Laboratory: Stages and Methods

International Nuclear Information System (INIS)

Deken, J.

2009-01-01

Advocating for the good of the SLAC Archives and History Office (AHO) has not been a one-time affair, nor has it been a one-method procedure. It has required taking time to ascertain the current and perhaps predict the future climate of the Laboratory, and it has required developing and implementing a portfolio of approaches to the goal of building a stronger archive program by strengthening and appropriately expanding its resources. Among the successful tools in the AHO advocacy portfolio, the Archives Program Review Committee has been the most visible. The Committee and the role it serves as well as other formal and informal advocacy efforts are the focus of this case study My remarks today will begin with a brief introduction to advocacy and outreach as I understand them, and with a description of the Archives and History Office's efforts to understand and work within the corporate culture of the SLAC National Accelerator Laboratory. I will then share with you some of the tools we have employed to advocate for the Archives and History Office programs and activities; and finally, I will talk about how well - or badly - those tools have served us over the past decade.

Present and future developments on the SLAC three-kilometer accelerator

International Nuclear Information System (INIS)

Loew, G.A.

1977-07-01

A review is given of the innovations which have recently been made or are being planned on the SLAC three-kilometer accelerator. A brief review of overall performance statistics is given, the beam is followed from its origin to the experimental areas. The injector with its new polarized guns, some highlights of klystron research, the SLED or SLAC Energy Development Program, which will boost the electron energy into the 30 to 40 GeV range, and some associated beam loading and beam breakup implications are described. Following these, a brief survey of other microwave developments is given. Some of the innovations being implanted in computer control are summarized, and the changes being planned for the generation and delivery of e +- beams to the PEP ring are discussed

Proceedings of the SLAC/KEK linear collider workshop on damping ring

International Nuclear Information System (INIS)

Urakawa, J.; Yoshioka, M.

1992-07-01

Since the SLAC/KEK joint meeting was first held at SLAC in March 1987, we have had such a meeting annually with the present one the 6th. This meeting is planned to discuss the damping ring issue in particular. We have ever stressed the importance of study of damping rings and considered construction of a test damping ring as key issue for the ATF project, since we started construction of the ATF in 1987. In 1991 we had large-scale reconstruction of a building to make a shielded area where a 1.54 GeV injector linac for the ring is to be installed. (J.P.N.)

SLAC pulsed X-ray facility

Science.gov (United States)

Ipe, N. E.; McCall, R. C.; Baker, E. D.

1986-05-01

The Stanford Linear Accelerator Center (SLAC) operates a high energy (up to 33 GeV) linear accelerator delivering pulses up to a few microseconds wide. The pulsed nature of the electron beam creates problems in the detection and measurement of radiation both from the accelerator beam and the klystrons that provide the RF power for the accelerator. Hence, a pulsed X-ray facility has been built at SLAC mainly for the purpose of testing the response of different radiation detection instruments to pulsed radiation fields. The X-ray tube consists of an electron gun with a control grid. This provides a stream of pulsed electrons that can be accelerated towards a confined target-window. The window is made up of aluminum 0.051 cm (20 mils) thick, plated on the vacuum side with a layer of gold 0.0006 cm (1/4 mil) thick. The frequency of electron pulses can be varied by an internal pulser from 60 to 360 pulses per second with pulse widths of 360 ns to 5 ms. The pulse amplitude can be varied over a wide range of currents. An external pulser can be used to obtain other frequencies or special pulse shapes. The voltage across the gun can be varied from 0 to 100 kV. The major part of the X-ray tube is enclosed in a large walk-in-cabinet made of 1.9 cm (3/4 in) plywood and lined with 0.32 cm (1/8 in) lead to make a very versatile facility.

SLAC pulsed x-ray facility

International Nuclear Information System (INIS)

Ipe, N.E.; McCall, R.C.; Baker, E.D.

1986-05-01

The Stanford Linear Accelerator Center (SLAC) operates a high energy (up to 33 GeV) linear accelerator delivering pulses up to a few microseconds wide. The pulsed nature of the electron beam creates problems in the detection and measurement of radiation both from the accelerator beam and the klystrons that provide the rf power for the accelerator. Hence, a pulsed x-ray facility has been built at SLAC mainly for the purpose of testing the response of different radiation detection instruments to pulsed radiation fields. The x-ray tube consists of an electron gun with a control grid. This provides a stream of pulsed electrons that can be accelerated towards a confined target-window. The window is made up of aluminium 0.051 cm (20 mils) thick, plated on the vacuum side with a layer of gold 0.0006 cm (1/4 mil) thick. The frequency of electron pulses can be varied by an internal pulser from 60 to 360 pulses per second with pulse widths of 360 ns to 5 μs. The pulse amplitude can be varied over a wide range of currents. An external pulser can be used to obtain other frequencies or special pulse shapes. The voltage across the gun can be varied from 0 to 100 kV. The major part of the x-ray tube is enclosed in a large walk-in-cabinet made of 1.9 cm (3/4 in) plywood and lined with 0.32 cm (1/8 in) lead to make a very versatile facility. 3 refs., 5 figs

Progress report on the SLAC Linear Collider

International Nuclear Information System (INIS)

Rees, J.

1986-06-01

The SLAC Linear Collider project (SLC) is reported as being near completion. The performance specifications are tabulated both for the initial form and for eventual goals. Various parts of the SLC are described and the status of their construction is reported, including the front end electron gun and booster, the linac, damping ring, positron source, SLC arcs, and conventional facilities. 5 refs., 12 figs

Design of a semi-custom integrated circuit for the SLAC SLC timing control system

International Nuclear Information System (INIS)

Linstadt, E.

1984-10-01

A semi-custom (gate array) integrated circuit has been designed for use in the SLAC Linear Collider timing and control system. The design process and SLAC's experiences during the phases of the design cycle are described. Issues concerning the partitioning of the design into semi-custom and standard components are discussed. Functional descriptions of the semi-custom integrated circuit and the timing module in which it is used are given

The proposed alignment system for the Final Focus Test Beam at SLAC

International Nuclear Information System (INIS)

Ruland, R.E.; Fischer, G.E.

1990-09-01

This report describes the current state of work in progress with respect to the geometry, alignment requirements, scenarios, and hardware for meeting the tolerances of the Final Focus Test Beam (FFTB) at SLAC. The methods and systems proposed acknowledge that component motion at the micron level, from whatever cause (ground motion, thermal effects, etc.) must be measured on-line and compensated for on relatively short time scales. To provide an integrated alignment/positioning package, some unique designs for reference systems, calibration of effect electric and magnetic centers, and component movers are introduced. 24 refs., 28 figs

The SLAC linear collider

International Nuclear Information System (INIS)

Phinney, N.

1992-01-01

The SLAC Linear Collider has begun a new era of operation with the SLD detector. During 1991 there was a first engineering run for the SLD in parallel with machine improvements to increase luminosity and reliability. For the 1992 run, a polarized electron source was added and more than 10,000 Zs with an average of 23% polarization have been logged by the SLD. This paper discusses the performance of the SLC in 1991 and 1992 and the technical advances that have produced higher luminosity. Emphasis will be placed on issues relevant to future linear colliders such as producing and maintaining high current, low emittance beams and focusing the beams to the micron scale for collisions. (Author) tab., 2 figs., 18 refs

SLAC Users Bulletin No. 102, November 1985-April 1986

International Nuclear Information System (INIS)

Keller, L.P.; Edminster, D.

1986-01-01

The status experimental activities at SLAC is reported, including the long-range schedule and a list of approved high-energy experiments. Work on PEP, SPEAR, and the SLC is included, as well as computing. Such operational data as operating hours and experimental hours are given.

Measurement of the longitudinal wakefield and the bunch shape in the SLAC linac

International Nuclear Information System (INIS)

Bane, K.L.F.; Decker, F.J.; Seeman, J.T.; Zimmermann, F.

1997-05-01

The authors report on measurements of the bunch energy spectrum at the end of the SLAC linac. Using the spectra obtained for two different linac rf phases they obtain both the bunch induced voltage and the longitudinal distribution of the bunch. The measurement results are compared with theoretical predictions. In particular, the induced voltage is in good agreement with that obtained using the calculated wake function for the SLAC linac. This measurement technique may be useful for monitoring changes of the linac bunch shape in the SLC

SLAC-Linac-Collider (SLC) Project

International Nuclear Information System (INIS)

Wiedemann, H.

1981-02-01

The proposed SLAC Linear Collider Project (SLC) and its features are described in this paper. In times of ever increasing costs for energy the electron storage ring principle is about to reach its practical limit. A new class of colliding beam beam facilities, the Linear Colliders, are getting more and more attractive and affordable at very high center-of-mass energies. The SLC is designed to be a poineer of this new class of colliding beam facilities and at the same time will serve as a valuable tool to explore the high energy physics at the level of 100 GeV in the center-of-mass system

The SLAC polarized electron source

International Nuclear Information System (INIS)

Tang, H.; Alley, R.; Frisch, J.

1995-06-01

The SLAC polarized electron source employs a photocathode DC high voltage gun with a loadlock and a YAG pumped Ti:sapphire laser system for colliding beam experiments or a flash lamp pumped Ti:sapphire laser for fixed target experiments. It uses a thin, strained GaAs(100) photocathode, and is capable of producing a pulsed beam with a polarization of ≥80% and a peak current exceeding 10 A. Its operating efficiency has reached 99%. The physics and technology of producing high polarization electron beams from a GaAs photocathode will be reviewed. The prospects of realizing a polarized electron source for future linear colliders will also be discussed

Production of high intensity electron bunches for the SLAC Linear Collider

International Nuclear Information System (INIS)

James, M.B.

1987-08-01

This thesis describes the design and performance of a high intensity electron injecfor for the SLAC Linear Collider. Motivation for the collider and the specifications for the injector are discussed. An analytic theory of the bunching and capture of electrons by rf fields is discussed in the limit of low space charge and small signal. The design and performance of SLAC's main injector are described to illustrate a successful application of this theory. The bunching and capture of electrons by rf fields are then discussed in the limit of high space charge and large signal, and a description of the design of the collider injector follows. In the limit of high space charge forces and large rf signals, the beam dynamics are considerably more complex and numerical simulations are required to predict particle motion. A computer code which models the longitudinal dynamics of electrons in the presence of space charge and rf fields is described. The results of the simulations, the resulting collider injector design and the various components which make up the collider injector are described. These include the gun, subharmonic bunchers, traveling-wave buncher and velocity-of-light accelerator section. Finally, the performance of the injector is described including the beam intensity, bunch length, transverse emittance and energy spectrum. While the final operating conditions differ somewaht from the design, the performance of the collider injector is in good agreement with the numerical simulations and meets all of the collider specifications. 28 refs

Upgrade of the SLAC SLED II Pulse Compression System Based on Recent High Power Tests

International Nuclear Information System (INIS)

Vlieks, A.E.; Fowkes, W.R.; Loewen, R.J.; Tantawi, S.G.

2011-01-01

In the Next Linear Collider (NLC) it is expected that the high power rf components be able to handle peak power levels in excess of 400 MW. We present recent results of high power tests designed to investigate the RF breakdown limits of the X-band pulse compression system used at SLAC. (SLED-II). Results of these tests show that both the TE 01 -TE 10 mode converter and the 4-port hybrid have a maximum useful power limit of 220-250 MW. Based on these tests, modifications of these components have been undertaken to improve their peak field handling capability. Results of these modifications will be presented. As part of an international effort to develop a new 0.5-1.5 TeV electron-positron linear collider for the 21st century, SLAC has been working towards a design, referred to as 'The Next Linear Collider' (NLC), which will operate at 11.424 GHz and utilize 50-75 MW klystrons as rf power sources. One of the major challenges in this design, or any other design, is how to generate and efficiently transport extremely high rf power from a source to an accelerator structure. SLAC has been investigating various methods of 'pulse compressing' a relatively wide rf pulse ((ge) 1 μs) from a klystron into a narrower, but more intense, pulse. Currently a SLED-II pulse compression scheme is being used at SLAC in the NLC Test Accelerator (NLCTA) and in the Accelerator Structures Test Area (ASTA) to provide high rf power for accelerator and component testing. In ASTA, a 1.05 μs pulse from a 50 MW klystron was successfully pulse compressed to 205 MW with a pulse width of 150 ns. Since operation in NLC will require generating and transporting rf power in excess of 400 MW it was decided to test the breakdown limits of the SLED-II rf components in ASTA with rf power up to the maximum available of 400 MW. This required the combining of power from two 50 MW klystrons and feeding the summed power into the SLED-II pulse compressor. Results from this experiment demonstrated that two of

Shower Counters for SLAC experiments E142/E143

Energy Technology Data Exchange (ETDEWEB)

Borel, H; Grenier, P; Le Meur, J; Lombard, R; Lugol, J C; Marroncle, J; Morgenstern, J; Mouly, J P; Paul, B; Staley, F; Terrien, Y [CEA Centre d` Etudes de Saclay, 91 - Gif-sur-Yvette (France). Dept. d` Astrophysique, de la Physique des Particules, de la Physique Nucleaire et de l` Instrumentation Associee; Breton, V; Comptour, C; Crouau, M; Fonvieille, H; Roblin, Y; Savinel, G [Clermont-Ferrand-2 Univ., 63 - Aubiere (France); Gearhart, R [Stanford Linear Accelerator Center, Menlo Park, CA (United States)

1994-10-01

The two electromagnetic calorimeters each made of 200 lead glass blocks used at SLAC to discriminate between electrons and pions and to measure electron energies are described. Procedures to reconstruct electron showers and to calibrate calorimeters are treated as well as the calorimeter performance. (author). 6 refs., 10 figs.

The design of a semi-custom intergrated circuit for the SLAC SLC timing control system

International Nuclear Information System (INIS)

Linstadt, E.

1985-01-01

A semi-custom (gate array) integrated circuit has been designed for use in the SLAC Linear Collider timing and control system. The design process and SLAC's experiences during the phases of the design cycle are described. Issues concerning the partitioning of the design into semi-custom and standard components are discussed. Functional descriptions of the semi-custom integrated circuit and the timing module in which it is used are given

Research and Development Toward a 4.5-1.5 Angstrom Linac Coherent Light Source (LCLS) at SLAC

International Nuclear Information System (INIS)

Tatchyn, R.; Arthur, J.; Baltay, M.

1995-08-01

In recent years significant studies have been initiated on the feasibility of utilizing a portion of the 3km S-band accelerator at SLAC to drive a short wavelength (4.5-1.5 A) Linac Coherent Light Source (LCLS), a Free Electron Laser (FEL) operating in the Self- Amplified Spontaneous Emission (SASE) regime. Electron beam requirements for single-pass saturation in a minimal time include: (1) a peak current in the 7 kA range, (2) a relative energy spread of <0.05%, and (3) a transverse emittance, ε[r-m], approximating the diffraction limit condition ε = λ / 4π, where lambda(m) is the output wavelength. Requirements on the insertion device include field error levels of 0.02% for keeping the electron bunch centered on and in phase with the amplified photons, and a focusing beta of 8 m/rad for inhibiting the dilution of its transverse density. Although much progress has been made in developing individual components and beam processing techniques necessary for LCLS operation down to approx. 20 A, a substantial amount of research and development is still required in a number of theoretical and experimental areas leading to the construction and operation of a 4.5-1.5 A LCLS. In this paper we report on a research and development program underway and in planning at SLAC for addressing critical questions in these areas

Integrated management tool for controls software problems, requests and project tasking at SLAC

International Nuclear Information System (INIS)

Rogind, D.; Allen, W.; Colocho, W.; DeContreras, G.; Gordon, J.; Pandey, P.; Shoaee, H.

2012-01-01

The Accelerator Directorate (AD) Instrumentation and Controls (ICD) Software (SW) Department at SLAC, with its service center model, continuously receives engineering requests to design, build and support controls for accelerator systems lab-wide. Each customer request can vary in complexity from a small software engineering change to a major enhancement. SLAC's Accelerator Improvement Projects (AIPs), along with DOE Construction projects, also contribute heavily to the work load. The various customer requests and projects, paired with the ongoing operational maintenance and problem reports, place a demand on the department that consistently exceeds the capacity of available resources. A centralized repository - comprised of all requests, project tasks, and problems - available to physicists, operators, managers, and engineers alike, is essential to capture, communicate, prioritize, assign, schedule, track, and finally, commission all work components. The Software Department has recently integrated request / project tasking into SLAC's custom online problem tracking 'Comprehensive Accelerator Tool for Enhancing Reliability' (CATER) tool. This paper discusses the newly implemented software request management tool - the workload it helps to track, its structure, features, reports, work-flow and its many usages. (authors)

Regulatory requirements for desalination plant coupled with nuclear reactor plant

International Nuclear Information System (INIS)

Yune, Young Gill; Kim, Woong Sik; Jo, Jong Chull; Kim, Hho Jung; Song, Jae Myung

2005-01-01

A small-to-medium sized reactor has been developed for multi-purposes such as seawater desalination, ship propulsion, and district heating since early 1990s in Korea. Now, the construction of its scaled-down research reactor, equipped with a seawater desalination plant, is planned to demonstrate the safety and performance of the design of the multi-purpose reactor. And the licensing application of the research reactor is expected in the near future. Therefore, a development of regulatory requirements/guides for a desalination plant coupled with a nuclear reactor plant is necessary for the preparation of the forthcoming licensing review of the research reactor. In this paper, the following contents are presented: the design of the desalination plant, domestic and foreign regulatory requirements relevant to desalination plants, and a draft of regulatory requirements/guides for a desalination plant coupled with a nuclear reactor plant

SLAC modulator operation and reliability in the SLC Era

International Nuclear Information System (INIS)

Donaldson, A.R.; Ashton, J.R.

1992-06-01

A discussion of the operation and reliability of the 244 modulators in the SLAC linac with an emphasis on the past three years of operation. The linac modulators were designed and built in the 60's, upgraded for the SLAC Linear Collider (SLC) in the mid 80s, and despite their age are still reliable accelerator components. The 60s modulator operated at 65 MW peak and 83 kW average power. The upgrade resulted in 150 MW peak output at an average power of 87 kW, a modest increase since the repetition rate was dropped from 360 to 120 Hz. In the present accelerator configuration, the Linac operates as a source of electrons and positrons to a single pass coillider. The classic collider is a storage ring filled with oppositely charged, counter-rotating particles which are allowed to collide until an accelerator fault occurs and the stored beams are aborted. A reasonable storage ring can store and collide particles for as long as eight hours with a 10 or 20 minute filling time. A single pass collider, + on the other hand, can only produce e - and e + collisions at whatever rate the source operates. To be effective the SLC must operate at 120 Hz with a very high degree of reliability and on a continuous basis. Fortunately, the linac has a modest excess of modulator/klystron systems which allows some measure of redundancy and hence some freedom from the constraint that all 244 modulator/klystrons operate simultaneously. Nonetheless, high importance is placed on modulator MTBF and MTRR or, in the parlance of reliability experts and accelerator physicists, availability. This is especially true of the modulators associated with the fundamental requirements of a collider such as injection, compression and positron production

SLAC linear collider: the machine, the physics, and the future

International Nuclear Information System (INIS)

Richter, B.

1981-11-01

The SLAC linear collider, in which beams of electrons and positrons are accelerated simultaneously, is described. Specifications of the proposed system are given, with calculated preditions of performance. New areas of research made possible by energies in the TeV range are discussed

Mega-electron-volt ultrafast electron diffraction at SLAC National Accelerator Laboratory

Energy Technology Data Exchange (ETDEWEB)

Weathersby, S. P.; Brown, G.; Chase, T. F.; Coffee, R.; Corbett, J.; Eichner, J. P.; Frisch, J. C.; Fry, A. R.; Gühr, M.; Hartmann, N.; Hast, C.; Hettel, R.; Jobe, R. K.; Jongewaard, E. N.; Lewandowski, J. R.; Li, R. K., E-mail: lrk@slac.stanford.edu; Lindenberg, A. M.; Makasyuk, I.; May, J. E.; McCormick, D. [SLAC National Accelerator Laboratory, 2575 Sand Hill Road, Menlo Park, California 94025 (United States); and others

2015-07-15

Ultrafast electron probes are powerful tools, complementary to x-ray free-electron lasers, used to study structural dynamics in material, chemical, and biological sciences. High brightness, relativistic electron beams with femtosecond pulse duration can resolve details of the dynamic processes on atomic time and length scales. SLAC National Accelerator Laboratory recently launched the Ultrafast Electron Diffraction (UED) and microscopy Initiative aiming at developing the next generation ultrafast electron scattering instruments. As the first stage of the Initiative, a mega-electron-volt (MeV) UED system has been constructed and commissioned to serve ultrafast science experiments and instrumentation development. The system operates at 120-Hz repetition rate with outstanding performance. In this paper, we report on the SLAC MeV UED system and its performance, including the reciprocal space resolution, temporal resolution, and machine stability.

''ARBOLA'' SLAC branch driver for PDP-11

International Nuclear Information System (INIS)

Oxoby, G.

1976-08-01

The wide use of CAMAC systems in the Large Aperture Solenoid Spectrometer facility led to the design of several dedicated CAMAC interfaces. The one described here features the implementation of bidirectional data transfers, and is used exclusively with the SLAC crate controller, 135-279. Efforts were made to ensure maximum versatility for acquisition of high-energy physics data. Specifications are set forth, and hardware and software (memory address register, word count register, data buffer register, and high-byte register) are described. 4 figures

Romania - NPP PLiM Between Regulatory Requirement / Oversight and Operator Safety / Financial Interest

International Nuclear Information System (INIS)

Goicea, Lucian

2012-01-01

Cernavoda Unit 1 PLiM started in the first third of its design life, to develop as regulatory requirements of the components of standards and programmes and to benefit by earlier implementation of the measures for achieving maximum operating life. CNCAN regulatory present approach on the utility PLiM combines the regulatory requirements on management system, ageing management provisions of periodic safety review, detailed technical requirements of ageing programmes and different techniques focusing only on safety issues. (author)

STANFORD (SLAC): B factory construction begins

Energy Technology Data Exchange (ETDEWEB)

Anon.

1994-03-15

At a ceremony marking the start of construction, members of the US Congress and Secretary of Energy Hazel O'Leary hailed the new Asymmetric B Factory as the key to continued vitality of the Stanford Linear Accelerator Center (SLAC). Being built in collaboration with the Lawrence Berkeley Laboratory and the Lawrence Livermore National Laboratory, the B factory is a $177 million upgrade of the existing PEP electron-positron collider. Scheduled for completion in 1998, the B factory will generate many millions of B mesons, allowing, among other physics, an intensive search for the phenomena of CP violation in the decays of these particles.

Nanosecond electron beam generation and instrumentation at SLAC

International Nuclear Information System (INIS)

Koontz, R.F.; Miller, R.H.

1975-01-01

The present SLAC injector system, including the latest beam chopping equipment, is discussed, and an updated diagram is given. The present equipment can produce almost any mix of chopped and single bunch beams for experimenters with a high degree of multiple beam compatibility. Topics covered include the grid pulsers, the pulse isolation transformers, the resonant choppers, the nonresonant chopper, the synchronization system, and the fast beam monitors. (PMA)

Plasma lenses for SLAC Final Focus Test facility

International Nuclear Information System (INIS)

Betz, D.; Cline, D.; Joshi, C.; Rajagopalan, S.; Rosenzweig, J.; Su, J.J.; Williams, R.; Chen, P.; Gundersen, M.; Katsouleas, T.; Norem, J.

1991-01-01

A collaborative group of accelerator and plasma physicists and engineers has formed with an interest in exploring the use of plasma lenses to meet the needs of future colliders. Analytic and computational models of plasma lenses are briefly reviewed and several design examples for the SLAC Final Focus Test Beam are presented. The examples include discrete, thick, and adiabatic lenses. A potential plasma source with desirable lens characteristics is presented

The status of the SLAC Linear Collider and of the Mark II detector

International Nuclear Information System (INIS)

Lankford, A.J.

1987-10-01

At SLAC we are currently involved in the exciting challenge of commissioning the first example of a new type of colliding beam accelerator, the SLAC Linear Collider, or SLC. The goals of the SLC are two-fold. It will explore the concept of linear colliders, and it will allow the study of physics on the Z 0 resonance. It accomplishes these goals by exploiting the existing SLAC linac and the large visible cross-section of approximately thirty nanobarns of the Z 0 . The MARK II detector will have the opportunity to be first to explore the physics in this regime. This paper briefly reports the status of the SLC and of the MARK II as of early October 1987, at which time commissioning efforts were interrupted in order to place the MARK II detector at the collision point and to incorporate some improvements to the SLC. The first portion of this report highlights some of the milestones achieved in the SLC commissioning and some of the problems encountered. The last portion outlines improvements made to the MARK II for physics at the SLC. 10 refs., 12 figs., 1 tab

The UCLA/SLAC Ultra-High Gradient Cerenkov Wakefield Accelerator Experiment

CERN Document Server

Thompson, Matthew C; Hogan, Mark; Ischebeck, Rasmus; Muggli, Patric; Rosenzweig, James E; Scott, A; Siemann, Robert; Travish, Gil; Walz, Dieter; Yoder, Rodney

2005-01-01

An experiment is planned to study the performance of dielectric Cerenkov wakefield accelerating structures at extremely high gradients in the GV/m range. This new UCLA/SLAC collaboration will take advantage of the unique SLAC FFTB electron beam and its demonstrated ultra-short pulse lengths and high currents (e.g., sz = 20 μm at Q = 3 nC). The electron beam will be focused down and sent through varying lengths of fused silica capillary tubing with two different sizes: ID = 200 μm / OD = 325 μm and ID = 100 μm / OD = 325 μm. The pulse length of the electron beam will be varied in order to alter the accelerating gradient and probe the breakdown threshold of the dielectric structures. In addition to breakdown studies, we plan to collect and measure coherent Cerenkov radiation emitted from the capillary tube to gain information about the strength of the accelerating fields. Status and progress on the experiment are reported.

Regulatory document R-104, Regulatory objectives, requirements and guidelines for the disposal of radioactive wastes - long-term aspects

International Nuclear Information System (INIS)

1987-01-01

The purpose and scope of this document is to present the regulatory basis for judging the long-term acceptability of radioactive waste disposal options. The basic objectives of radioactive waste disposal are given as are the regulatory requirements to be satisfied. (NEA)

Development of regulatory requirements/guides for desalination unit coupled with nuclear plant

International Nuclear Information System (INIS)

Jo, Jong Chull; Yune, Young Gill; Kim, Woong Sik

2005-10-01

The basic design of System-integrated Modular Advanced Reactor (SMART), a small-to-medium sized integral type pressurized water reactor (PWR) with the capacity of 330MWth, has been developed in Korea. In order to demonstrate the safety and performance of the SMART design, 'Development Project of SMART-P (SMART-Pilot Plant)' has been being performed as one of the 'National Mid and Long-term Atomic Energy R and D Programs', which includes design, construction, and start-up operation of the SMART-P with the capacity of 65MWth, a 1/5 scaled-down design of the SMART. At the same time, a study on the development of regulatory requirements/guides for the desalination unit coupled with nuclear plant has been carried out by KINS in order to prepare for the forthcoming SMART-P licensing. The results of this study performed from August of 2002 to October of 2005 can be summarized as follows: (1) The general status of desalination technologies has been survey. (2) The design of the desalination plant coupled with the SMART-P has been investigated. (3) The regulatory requirements/guides relevant to a desalination unit coupled with a nuclear plant have been surveyed. (4) A direction on the development of domestic regulatory requirements/guides for a desalination unit has been established. (5) A draft of regulatory requirements/guides for a desalination unit has been developed. (6) Expert technical reviews have been performed for the draft regulatory requirements/guides for a desalination unit. The draft regulatory requirements/guides developed in this study will be finalized and can be applied directly to the licensing of the SMART-P and SMART. Furthermore, it will be also applied to the licensing of the desalination unit coupled with the nuclear plant

STANFORD (SLAC): B factory construction begins

International Nuclear Information System (INIS)

Anon.

1994-01-01

At a ceremony marking the start of construction, members of the US Congress and Secretary of Energy Hazel O'Leary hailed the new Asymmetric B Factory as the key to continued vitality of the Stanford Linear Accelerator Center (SLAC). Being built in collaboration with the Lawrence Berkeley Laboratory and the Lawrence Livermore National Laboratory, the B factory is a $177 million upgrade of the existing PEP electron-positron collider. Scheduled for completion in 1998, the B factory will generate many millions of B mesons, allowing, among other physics, an intensive search for the phenomena of CP violation in the decays of these particles

Two microcomputer-controller applications at SLAC

International Nuclear Information System (INIS)

Struven, W.C.; Mallory, K.B.

1977-03-01

The SLAC Accelerator Control and Monitoring System, as originally implemented, was a manual (non-computer) control system with provisions to add computers at a later date. Since operation began in 1966, a PDP9 with a PDP8/e ''front end'' was added in the accelerator control room, and most recently, eight PDP8/f's were added in the two mile Klystron Gallery which are linked to the 8/e front end. A data link was added between the PDP9 and an SDS 925 in the Main Control Room. Tough panel interfaces were provided so that the Accelerator and Beam Switchyard could be controlled and monitored from one console

3D Modeling Activity for Novel High Power Electron Guns at SLAC

International Nuclear Information System (INIS)

Krasnykh, Anatoly

2003-01-01

The next generation of powerful electronic devices requires new approaches to overcome the known limitations of existing tube technology. Multi-beam and sheet beam approaches are novel concepts for the high power microwave devices. Direct and indirect modeling methods are being developed at SLAC to meet the new requirements in the 3D modeling. The direct method of solving of Poisson's equations for the multi-beam and sheet beam guns is employed in the TOPAZ 3D tool. The combination of TOPAZ 2D and EGUN (in the beginning) with MAFIA 3D and MAGIC 3D (at the end) is used in an indirect method to model the high power electron guns. Both methods complement each other to get reliable representation of the beam trajectories. Several gun ideas are under consideration at the present time. The collected results of these simulations are discussed

3D Modeling Activity for Novel High Power Electron Guns at SLAC

CERN Document Server

Krasnykh, Anatoly K

2003-01-01

The next generation of powerful electronic devices requires new approaches to overcome the known limitations of existing tube technology. Multi-beam and sheet beam approaches are novel concepts for the high power microwave devices. Direct and indirect modeling methods are being developed at SLAC to meet the new requirements in the 3D modeling. The direct method of solving of Poisson's equations for the multi-beam and sheet beam guns is employed in the TOPAZ 3D tool. The combination of TOPAZ 2D and EGUN (in the beginning) with MAFIA 3D and MAGIC 3D (at the end) is used in an indirect method to model the high power electron guns. Both methods complement each other to get reliable representation of the beam trajectories. Several gun ideas are under consideration at the present time. The collected results of these simulations are discussed.

A 2--4 nm Linac Coherent Light Source (LCLS) using the SLAC linac

International Nuclear Information System (INIS)

Winick, H.; Bane, K.; Boyce, R.

1993-05-01

We describe the use of the SLAC linac to drive a unique, powerful. short wavelength Linac Coherent Light Source (LCLS). Operating as an FEL, lasing would be achieved in a single pass of a high peak current electron beam through a long undulator by self-amplified spontaneous emission (SASE). The main components are a high-brightness rf photocathode electron gun; pulse compressors; about 1/5 of the SLAC linac; and a long undulator with a FODO quadrupole focussing system. Using electrons below 8 GeV, the system would operate at wavelengths down to about 3 nm, producing ≥10 GW peak power in sub-ps pulses. At a 120 Hz rate the average power is ∼ 1 W

Safety and regulatory requirements of nuclear power plants

International Nuclear Information System (INIS)

Kumar, S.V.; Bhardwaj, S.A.

2000-01-01

A pre-requisite for a nuclear power program in any country is well established national safety and regulatory requirements. These have evolved for nuclear power plants in India with participation of the regulatory body, utility, research and development (R and D) organizations and educational institutions. Prevailing international practices provided a useful base to develop those applicable to specific system designs for nuclear power plants in India. Their effectiveness has been demonstrated in planned activities of building up the nuclear power program as well as with unplanned activities, like those due to safety related incidents etc. (author)

dE/dx electronics for MARK II experiment at SLAC

International Nuclear Information System (INIS)

Bernstein, D.; Boyarski, A.; Coupal, D.; Feldman, G.; Paffrath, L.

1985-10-01

This paper describes a 100 MHz pulse digitizer for dE/dx measurements on the MARK II drift chamber at SLAC. The electronics provides the read-out of the detector's 5832 sense based on a 16-channel FASTBUS module. The basic element of the module is the TRW 6-bit Flash-ADC

Use of prioritization in meeting regulatory requirements

International Nuclear Information System (INIS)

Bowling, M.L.; Sommers, D.A.; Girvin, L.M.

1993-01-01

The use of prioritization in the allocation of resources is certainly not a new idea. However, the degree to which prioritization must now be used is much greater than ever before. In the past, utilities generally allocated the necessary resources to meet all regulatory requirements and commitments. Prioritization was then applied to the remaining nonregulatory but required needs. This approach to resource allocation is no longer appropriate for the current and projected economic and operating environment. Key reasons for this conclusion are discussed in this paper by staff from Virginia Power

Computer modelling of bunch-by-bunch feedback for the SLAC B-factory design

International Nuclear Information System (INIS)

Briggs, D.; Fox, J.D.; Hosseini, W.; Klaisner, L.; Morton, P.; Pellegrin, J.L.; Thompson, K.A.; Lambertson, G.

1991-05-01

The SLAC B-factory design, with over 1600 high current bunches circulating in each ring, will require a feedback system to avoid coupled-bunch instabilities. A computer model of the storage ring, including the RF system, wave fields, synchrotron radiation loss, and the bunch-by-bunch feedback system is presented. The feedback system model represents the performance of a fast phase detector front end (including system noise and imperfections), a digital filter used to generate a correction voltage, and a power amplifier and beam kicker system. The combined ring-feedback system model is used to study the feedback system performance required to suppress instabilities and to quantify the dynamics of the system. Results are presented which show the time development of coupled bunch instabilities and the damping action of the feedback system. 3 refs., 5 figs., 2 tabs

Status of the SLAC SNOOP diagnostic module for FASTBUS

International Nuclear Information System (INIS)

Walz, H.V.; Gustavson, D.B.

1983-03-01

A SNOOP Diagnostic Module for FASTBUS is under development at SLAC. The SNOOP Module resides on a FASTBUS crate segment and provides diagnostic monitoring and testing capability. It consists of a high-speed ECL front-end to monitor and single-step segment operations, a simple master interface, and a control processor with two serial communication ports. Module features and specifications are summrized, and prototype hardware is shown

Regulatory requirements of the integrated technology demonstration program, Savannah River Site (U)

International Nuclear Information System (INIS)

Bergren, C.L.

1992-01-01

The integrated demonstration program at the Savannah River Site (SRS) involves demonstration, testing and evaluation of new characterization, monitoring, drilling and remediation technologies for soils and groundwater impacted by organic solvent contamination. The regulatory success of the demonstration program has developed as a result of open communications between the regulators and the technical teams involved. This open dialogue is an attempt to allow timely completion of applied environmental restoration demonstrations while meeting all applicable regulatory requirements. Simultaneous processing of multiple regulatory documents (satisfying RCRA, CERCLA, NEPA and various state regulations) has streamlined the overall permitting process. Public involvement is achieved as various regulatory documents are advertised for public comment consistent with the site's community relations plan. The SRS integrated demonstration has been permitted and endorsed by regulatory agencies, including the Environmental Protection Agency (EPA) and the South Carolina Department of Health and Environmental Control. EPA headquarters and regional offices are involved in DOE's integrated Demonstration Program. This relationship allows for rapid regulatory acceptance while reducing federal funding and time requirements. (author)

SLAC's Polarized Electron Source LaserSystem and Minimization of Helicity Correlations for the E-158 Parity Violation Experiment

CERN Document Server

Humensky, T

2002-01-01

SLAC E-158 is an experiment designed to make the first measurement of parity violation in Moeller scattering. E-158 will measure the right-left cross-section asymmetry, A sub L sub R sup M sup o sup e sup l sup l sup e sup r , in the elastic scattering of a 45-GeV polarized electron beam off unpolarized electrons in a liquid hydrogen target. E-158 plans to measure the expected Standard Model asymmetry of approx 10 sup - sup 7 to an accuracy of better than 10 sup - sup 8. To make this measurement, the polarized electron source requires for operation an intense circularly polarized laser beam and the ability to quickly switch between right- and left-helicity polarization states with minimal right-left helicity-correlated asymmetries in the resulting beam parameters (intensity, position, angle, spot size, and energy), sup b sup e sup a sup m A sub L sub R 's. This laser beam is produced by a unique SLAC-designed flashlamp-pumped Ti:Sapphire laser and is propagated through a carefully designed set of polarization...

Physics at the SLC [SLAC Linear Collider

International Nuclear Information System (INIS)

Swartz, M.L.

1990-11-01

The SLAC Linear Collider (SLC) was constructed in the years 1983--1987 for two principal reasons: to develop the accelerator physics and technology that are necessary for the construction of future linear electron-positron colliders; and to produce electron-positron collisions at the Z 0 pole and to study the physics of the weak neutral current. To date, the SLC program has been quite successful at achieving the first goal. The machine has produced and collided high energy electron and positron beams of three-micron transverse size. The problems of operating an open geometry detector in an environment that is more akin to those found in fixed-target experiments than in storage rings have largely been solved. As a physics producing venture, the SLC has been less successful than was originally hoped but more successful than is commonly believed. Some of the results that have been produced by the Mark II experiment with a very modest data sample are competitive with those that have been produced with much larger samples by the four LEP collaborations. At the current, time, SLAC is engaged in an ambitious program to upgrade the SLC luminosity and to exploit one of its unique features, a spin polarized electron beam. These lectures are therefore organized into three sections: a brief description of the SLC; a review of the physics results that have been achieved with the Mark II detector; a description of the SLC's future: the realization and use of a polarized electron beam

Proceedings of the SLC workshop on experimental use of the SLAC Linear Collider

International Nuclear Information System (INIS)

1982-03-01

In March 1981, the SLAC management, together with the SLAC users organization, invited interested physicists to a three day meeting to discuss the laboratory's plans and progress on the new colliding e + e - machine - the Stanford Linear Collider (SLC). Those attending were encouraged to join together to study the challenges and opportunities presented by the SLC. The study of the parameters for experiments on 100 GeV e + e - collisions, and the reviews of the state-of-the-art in the four areas of detector technology - Tracking, Calorimetry, Particle Identification and Electronics and Computing - were undertaken from a general standpoint, and not from the particular perspective of a specific experimental proposal. Nine sections were prepared separately for the data base

Radiation Dose Measurement for High-Intensity Laser Interactions with Solid Targets at SLAC

Energy Technology Data Exchange (ETDEWEB)

Liang, Taiee [SLAC National Accelerator Lab., Menlo Park, CA (United States)

2015-09-25

A systematic study of photon and neutron radiation doses generated in high-intensity laser-solid interactions is underway at SLAC National Accelerator Laboratory. We found that these laser-solid experiments are being performed using a 25 TW (up to 1 J in 40 fs) femtosecond pulsed Ti:sapphire laser at the Linac Coherent Light Source’s (LCLS) Matter in Extreme Conditions (MEC) facility. Additionally, radiation measurements were performed with passive and active detectors deployed at various locations inside and outside the target chamber. Results from radiation dose measurements for laser-solid experiments at SLAC MEC in 2014 with peak intensity between 10¹⁸ to 7.1x10¹⁹ W/cm² are presented.

Pulsed rf superconductivity program at SLAC

International Nuclear Information System (INIS)

Campisi, I.E.; Farkas, Z.D.

1984-08-01

Recent tests performed at SLAC on superconducting TM 010 caavities using short rf pulses (less than or equal to 2.5 μs) have established that at the cavity surface magnetic fields can be reached in the vicinity of the theoretical critical fields without an appreciable increase in average losses. Tests on niobium and lead cavities are reported. The pulse method seems to be best suited to study peak field properties of superconductors in the microwave band, without the limitations imposed by defects. The short pulses also seem to be more effective in decreasing the causes of field emission by rf processing. Applications of the pulsed rf superconductivity to high-gradient linear accelerators are also possible

PEP radiation shielding tests in SLAC A Beam

International Nuclear Information System (INIS)

Ash, W.; DeStaebler, H.; Harris, J.; Jenkins, T.; Murray, J.

1977-09-01

Radiation shielding tests designed to simulate possible conditions in and around the PEP experimental halls were conducted. The SLAC A Beam was targeted in the block tunnel at a point about midway between End Station A and Beam Dump East. At that site it was relatively easy to rearrange the concrete block structure to simulate the various shielding configurations under consideration for PEP. Extensive surveys of neutron and ionizing radiation were made. Complete results of the shielding tests are given

Development of operator requested control system applications: Experience with the SLC control system at SLAC

International Nuclear Information System (INIS)

Stanek, M.

1995-01-01

The SLC Control system at SLAC has evolved into a powerful tool for operation of the accelerator and for troubleshooting the unique problems encountered in extracting maximum performance from the SLC. The evolution has included the development of many custom applications and user interface features generated from accelerator operator and accelerator physicist requests. These applications are written and maintained primarily by the Controls Software Engineering group, and not by the users themselves. The process of developing and supporting user requested control systems applications at SLAC is described, including the effects of organizational structure, formal and informal procedures, and control system architecture

Annual Site Environmental Report: 2006

International Nuclear Information System (INIS)

Nuckolls, H

2008-01-01

This report provides information about environmental programs during the calendar year (CY) of 2006 at the Stanford Linear Accelerator Center (SLAC), Menlo Park, California. Activities that span the calendar year; i.e., stormwater monitoring covering the winter season of 2006/2007 (October 2006 through May 2007), are also included. Production of an annual site environmental report (ASER) is a requirement established by the United States Department of Energy (DOE) for all management and operating (M and O) contractors throughout the DOE complex. SLAC is a federally-funded research and development center with Stanford University as the M and O contractor. SLAC continued to follow the path to self-declare an environmental management system under DOE Order 450.1, 'Environmental Protection Program' and effectively applied environmental management in meeting the site's integrated safety and environmental management system goals. For normal daily activities, all SLAC managers and supervisors are responsible for ensuring that proper procedures are followed so that Worker safety and health are protected; The environment is protected; and Compliance is ensured. Throughout 2006, SLAC focused on these activities through the SLAC management systems. These systems were also the way SLAC approached implementing 'greening of the government' initiatives such as Executive Order 13148. The management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. The SLAC Office of Assurance was created during 2006 in response to DOE Order 226.1. During 2006, there were no reportable releases to the environment from SLAC operations, and there were no Notice of Violations issued to SLAC from any of the regulatory agencies that oversee SLAC. In addition, many improvements in waste minimization, recycling, stormwater drain system, groundwater restoration, and SLAC's chemical management system (CMS) were continued during 2006 to better manage

Neutron dosimetry at SLAC: Neutron sources and instrumentation

International Nuclear Information System (INIS)

Liu, J.C.; Jenkins, T.M.; McCall, R.C.; Ipe, N.E.

1991-10-01

This report summarizes in detail the dosimetric characteristics of the five radioisotopic type neutron sources ( 238 PuBe, 252 Cf, 238 PuB, 238 PuF 4 , and 238 PuLi) and the neutron instrumentation (moderated BF 3 detector, Anderson-Braun (AB) detector, AB remmeter, Victoreen 488 Neutron Survey Meter, Beam Shut-Off Ionization Chamber, 12 C plastic scintillator detector, moderated indium foil detector, and moderated and bare TLDs) that are commonly used for neutron dosimetry at the Stanford Linear Accelerator Center (SLAC). 36 refs,. 19 figs

Beam-beam studies for the proposed SLAC/LBL/LLNL B Factory

International Nuclear Information System (INIS)

Furman, M.A.

1991-05-01

We present a summary of beam-beam dynamics studies that have been carried out to date for the proposed SLAC/LBL/LLNL B Factory. Most of the material presented here is contained in the proposal's Conceptual Design Report, although post-CDR studies are also presented. 15 refs., 6 figs., 2 tabs

Regulatory and administrative requirements for practice of nuclear medicine in India

International Nuclear Information System (INIS)

Tandon, Pankaj

1998-01-01

In order to ensure safety of the patients, staff and public in the practice of nuclear medicine, including in-vivo diagnostic investigations, radionuclide therapy and in research using unsealed radioactive substances a number of administrative and regulatory procedures are adopted. The salient features of regulatory and administrative requirements for practice of nuclear medicine in India are discussed

Assessment of compliance with regulatory requirements for a best estimate methodology for evaluation of ECCS

Energy Technology Data Exchange (ETDEWEB)

Lee, Un Chul; Jang, Jin Wook; Lim, Ho Gon; Jeong, Ik [Seoul National Univ., Seoul (Korea, Republic of); Sim, Suk Ku [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

2000-03-15

Best estimate methodology for evaluation of ECCS proposed by KEPCO(KREM) os using thermal-hydraulic best-estimate code and the topical report for the methodology is described that it meets the regulatory requirement of USNRC regulatory guide. In this research the assessment of compliance with regulatory guide. In this research the assessment of compliance with regulatory requirements for the methodology is performed. The state of licensing procedure of other countries and best-estimate evaluation methodologies of Europe is also investigated, The applicability of models and propriety of procedure of uncertainty analysis of KREM are appraised and compliance with USNRC regulatory guide is assessed.

Single bunch beam loading on the SLAC three-kilometer accelerator

International Nuclear Information System (INIS)

Koontz, R.F.; Loew, G.A.; Miller, R.H.; Wilson, P.B.

1977-03-01

Since the report on single bunch beam loading experiments at SLAC at the 1975 Particle Accelerator Conference, it has been possible to obtain a much better understanding and agreement of theoretical and experimental results related to this problem. These improvements were made possible by two developments: the generation of a ''wake-field'' function for the SLAC 3-km slow-wave structure and the use of this function to calculate single bunch energy spectra. The wake-field function which gives the time decay of the fields generated by the passage of a delta-function beam was derived by summing all the TM cylindrically symmetrical modes of an equivalent accelerator cavity. By multiplying this wake-field function by a measured bunch density function and integrating along the bunch, it is possible to calculate the energy of each electron in the bunch. This in turn enables one to predict the energy spectrum for any given phase angle of the bunch with respect to the crest of the rf accelerating wave. Agreement between these calculations and experimental measurements is very good. These results are presented, and the possible sources of some of the remaining discrepancies are discussed

Single bunch beam loading on the SLAC three-kilometer accelerator

International Nuclear Information System (INIS)

Koontz, R.F.; Loew, G.A.; Miller, R.H.; Wilson, P.B.

1977-01-01

Since the report on single bunch beam loading experiments at SLAC at the 1975 Particle Accelerator Conference, it has been possible to obtain a much better understanding and agreement of theoretical and experimental results related to this problem. These improvements have been made possible by two developments: the generation of a ''wake-field'' function for the SLAC 3-km slow-wave structure and the use of this function to calculate single bunch energy spectra. The wake-field function which gives the time decay of the fields generated by the passage of a delta-function beam was derived by summing all the TM cylindrically symmetrical modes of an equivalent accelerator cavity. By multiplying this wake-field function by a measured bunch density function and integrating along the bunch, it is possible to calculate the energy of each electron in the bunch. This in turn enables one to predict the energy spectrum for any given phase angle of the bunch with respect to the crest of the rf accelerating wave. Agreement between these calculations and experimental measurements is very good. These results are presented and the possible sources of some of the remaining discrepancies are discussed

Neutron dosimetry at SLAC: Neutron sources and instrumentation

Energy Technology Data Exchange (ETDEWEB)

Liu, J.C.; Jenkins, T.M.; McCall, R.C.; Ipe, N.E.

1991-10-01

This report summarizes in detail the dosimetric characteristics of the five radioisotopic type neutron sources ({sup 238}PuBe, {sup 252}Cf, {sup 238}PuB, {sup 238}PuF{sub 4}, and {sup 238}PuLi) and the neutron instrumentation (moderated BF{sub 3} detector, Anderson-Braun (AB) detector, AB remmeter, Victoreen 488 Neutron Survey Meter, Beam Shut-Off Ionization Chamber, {sup 12}C plastic scintillator detector, moderated indium foil detector, and moderated and bare TLDs) that are commonly used for neutron dosimetry at the Stanford Linear Accelerator Center (SLAC). 36 refs,. 19 figs.

SLAC to host symposium celebrating 10th anniversary of first website in America

CERN Multimedia

2001-01-01

Many of the programmers, web designers and scientists who collaborated to create the world wide web will be in SLAC for a two-day symposium to celebrate the 10th anniversary of the first website in America.

Operating experience with the polarized electron gun at SLAC

International Nuclear Information System (INIS)

Alguard, M.J.; Baum, G.; Clendenin, J.E.; Hughes, V.W.; Lubell, M.S.; Miller, R.H.; Raith, W.; Schuler, K.P.; Sodja, J.

1977-03-01

During the two years of operation of the SLAC Polarized Electron Gun (PEGGY), the electron intensity delivered to the target has increased from 7 x 10 7 e - /pulse to 1 x 10 9 e - /pulse. The polarization is 0.85 with no measurable degradation caused by acceleration through the linear accelerator. The predominant cause of downtime is replenishment of lithium, which now averages 43 hours. The lifetime of a lithium load is about 175 hours

17 CFR 1.52 - Self-regulatory organization adoption and surveillance of minimum financial requirements.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 1 2010-04-01 2010-04-01 false Self-regulatory organization... Miscellaneous § 1.52 Self-regulatory organization adoption and surveillance of minimum financial requirements. (a) Each self-regulatory organization must adopt, and submit for Commission approval, rules...

Spectral function calculation of angle wakes, wake moments, and misalignment wakes for the SLAC Damped Detuned Structures (DDS)

International Nuclear Information System (INIS)

Jones, R.M.; Miller, R.H.; Kroll, N.M.

1997-05-01

Transverse wake functions so far reported for the SLAC DDS have been limited to those caused by uniform offset of the drive beam in a straight perfectly aligned structure. The complete description of the betatron oscillations of wake coupled bunches requires an array of wake functions, referred to as moments. Modifications of these arrays induced by structure misalignments are also of interest. In this paper we express the array elements in terms of a spectral function array. Examples are given based upon DDS1

Galectin-1 is required for the regulatory function of B cells.

Science.gov (United States)

Alhabbab, R; Blair, P; Smyth, L A; Ratnasothy, K; Peng, Q; Moreau, A; Lechler, R; Elgueta, R; Lombardi, G

2018-02-09

Galectin-1 (Gal-1) is required for the development of B cells in the bone marrow (BM), however very little is known about the contribution of Gal-1 to the development of B cell regulatory function. Here, we report an important role for Gal-1 in the induction of B cells regulatory function. Mice deficient of Gal-1 (Gal-1 -/- ) showed significant loss of Transitional-2 (T2) B cells, previously reported to include IL-10 + regulatory B cells. Gal-1 -/- B cells stimulated in vitro via CD40 molecules have impaired IL-10 and Tim-1 expression, the latter reported to be required for IL-10 production in regulatory B cells, and increased TNF-α expression compared to wild type (WT) B cells. Unlike their WT counterparts, T2 and T1 Gal-1 -/- B cells did not suppress TNF-α expression by CD4 + T cells activated in vitro with allogenic DCs (allo-DCs), nor were they suppressive in vivo, being unable to delay MHC-class I mismatched skin allograft rejection following adoptive transfer. Moreover, T cells stimulated with allo-DCs show an increase in their survival when co-cultured with Gal-1 -/- T2 and MZ B cells compared to WT T2 and MZ B cells. Collectively, these data suggest that Gal-1 contributes to the induction of B cells regulatory function.

Analysis of regulatory requirement for beyond design basis events of SMART

International Nuclear Information System (INIS)

Kim, W. S.; Seol, K. W.

2000-01-01

To enhance the safety of SMART reactor, safety and regulatory requirements associated with beyond design basis events (beyond BDE), which were developed and applied to advanced light water reactor designs, were analyzed along with a design status of passive reactor. And, based on these requirements, their applicability on the SMART design was evaluated. In the design aspect, severe accident prevention and mitigation features, containment performance, and accident management were analyzed. The evaluation results show that the requirement related to beyond DBE such as ATWS, loss of residual heat removal during shutdown operation, station blackout, fire, inter-system LOCA, and well-known events from severe accident phenomena is applicable to the SMART design. However, comprehensive approach against beyond DBE is not yet provided in the SMART design, and then it is required to designate and analyze the beyond DBE-related features. This study is expected to contribute to efforts to improve plant safety and to establish regulatory requirements for safety review

17 CFR 249.821 - Form PILOT, information required of self-regulatory organizations operating pilot trading systems...

Science.gov (United States)

2010-04-01

... required of self-regulatory organizations operating pilot trading systems pursuant to § 240.19b-5 of this... Associations § 249.821 Form PILOT, information required of self-regulatory organizations operating pilot trading systems pursuant to § 240.19b-5 of this chapter. This form shall be used by all self-regulatory...

Regulatory objectives, requirements and guidelines for the disposal of radioactive wastes - long-term aspects

International Nuclear Information System (INIS)

1987-01-01

It is the purpose of this document to present the regulatory basis for judging the long-term acceptability of radioactive waste disposal options, assuming that the operational aspects of waste emplacement and facility closure satisfy the existing regulatory framework of requirements. Basic objectives of radioactive waste disposal are given, as are the regulatory requirements which must be satisfied in order to achieve these objectives. In addition, guidelines are given on the application of the radiological requirements to assist proponents in the preparation of submissions to the Atomic Energy Control Board (AECB). The primary focus of the requirements is on radiation protection, although environmental protection and institutional controls are also addressed in a more general way since these factors stem directly from the overall objectives for radioactive waste disposal

Annual Site Environmental Report: 2005

Energy Technology Data Exchange (ETDEWEB)

sabba, d

2007-02-03

This report provides information about environmental programs during 2005 at the Stanford Linear Accelerator Center (SLAC). Seasonal activities that span calendar years are also included. Production of an annual site environmental report (ASER) is a requirement established by the United States Department of Energy (DOE) for all management and operating (M&O) contractors throughout the DOE complex. SLAC is a federally-funded research and development center with Stanford University as the M&O contractor. SLAC effectively applied environmental management in meeting the site's integrated safety and environmental management system (ISEMS) goals. For normal daily activities, all SLAC managers and supervisors are responsible for ensuring that proper procedures are followed so that: (1) Worker safety and health are protected; (2) The environment is protected; and (3) Compliance is ensured. Throughout 2005, SLAC focused on these activities through the SLAC management systems (described in Chapter 3). These systems were also the way SLAC approached implementing ''greening of the government'' initiatives such as Executive Order 13148. The management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. There were no reportable releases to the environment from SLAC operations during 2005. In addition, many improvements were continued during 2005, in waste minimization, recycling, stormwater drain system, groundwater restoration, and implementing a chemical management system (CMS) to better manage chemical use. Program-specific details are discussed.

Annual Site Environmental Report Prepared for the Department of Energy,under contract number DE-AC03-76SF00515 January - December 2001

International Nuclear Information System (INIS)

Russak, Hillary M.

2003-01-01

This report provides information about environmental programs during 2001 at the Stanford Linear Accelerator Center (SLAC). Also included are seasonal activities that cross calendar-year divisions. Production of the annual site environmental report (ASER) is a requirement established by the US Department of Energy (DOE) for all management and operating (M and O) contractors throughout the DOE complex. SLAC is federally-funded, research development center with Stanford University as the M and O contractor. The most noteworthy information in this report is summarized in this section. This summary demonstrates the effective application of SLAC environmental management in meeting the site's Integrated Safety Management System (ISMS) goals. For normal daily activities, all SLAC managers and supervisors are responsible for ensuring that proper procedures are followed to meet the ISMS goals: Worker safety and health are protected; The environment is protected; and Compliance is assured. Throughout 2001, SLAC focused on these activities through the SLAC management systems. These systems were also the ways SLAC approached implementing the ''Greening of the Government'' initiatives (such as Executive Order 13148). The management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. SLAC did not receive any notices of violation during 2001. In addition, many improvements were continued during 2001, including improvements in the storm drain system, improved ground water monitoring capabilities, and enhancements to the system to manage the generation of mixed wastes. Environmental program-specific summary details are shown below

Annual Site Environmental Report: 2002

Energy Technology Data Exchange (ETDEWEB)

Nuckolls, H.; /SLAC

2006-04-19

This report provides information about environmental programs during 2002 at the Stanford Linear Accelerator Center (SLAC). Seasonal activities that span calendar years are also included. Production of an annual site environmental report (ASER) is a requirement established by the United States Department of Energy (DOE) for all management and operating (M&O) contractors throughout the DOE complex. SLAC is a federally-funded, research and development center with Stanford University as the M&O contractor. The most noteworthy information in this report is summarized in this section. This summary demonstrates the effective application of SLAC environmental management in meeting the site's integrated safety management system (ISMS) goals. For normal daily activities, all SLAC managers and supervisors are responsible for ensuring that proper procedures are followed so that worker safety and health are protected; the environment is protected; and compliance is ensured. Throughout 2002, SLAC focused on these activities through the SLAC management systems (described in Chapter 3). These systems were also the way SLAC approached implementing ''greening of the government'' initiatives such as Executive Order 13148. The management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. SLAC did not receive any notices of violation during 2002. In addition, many improvements were continued during 2002, in decreasing air emission rates, the storm drain system, groundwater restoration, and planning for a chemical management system to manage chemical use better.

Annual Site Environmental Report Prepared for the Department of Energy,under contract number DE-AC03-76SF00515 January - December 2001

Energy Technology Data Exchange (ETDEWEB)

Russak, Hillary M.

2003-05-06

This report provides information about environmental programs during 2001 at the Stanford Linear Accelerator Center (SLAC). Also included are seasonal activities that cross calendar-year divisions. Production of the annual site environmental report (ASER) is a requirement established by the US Department of Energy (DOE) for all management and operating (M&O) contractors throughout the DOE complex. SLAC is federally-funded, research development center with Stanford University as the M and O contractor. The most noteworthy information in this report is summarized in this section. This summary demonstrates the effective application of SLAC environmental management in meeting the site's Integrated Safety Management System (ISMS) goals. For normal daily activities, all SLAC managers and supervisors are responsible for ensuring that proper procedures are followed to meet the ISMS goals: Worker safety and health are protected; The environment is protected; and Compliance is assured. Throughout 2001, SLAC focused on these activities through the SLAC management systems. These systems were also the ways SLAC approached implementing the ''Greening of the Government'' initiatives (such as Executive Order 13148). The management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. SLAC did not receive any notices of violation during 2001. In addition, many improvements were continued during 2001, including improvements in the storm drain system, improved ground water monitoring capabilities, and enhancements to the system to manage the generation of mixed wastes. Environmental program-specific summary details are shown below.

Passive performance monitoring and traffic characteristics on the SLAC internet border

International Nuclear Information System (INIS)

Logg, C.; Cottrell, L.

2001-01-01

Understanding how the Internet is used by HEP is critical to optimizing the performance of the inter-lab computing environment. Typically use requirements have been defined by discussions between collaborators. However, later analysis of the actual traffic has show this is often misunderstood and actual use is significantly different to that predicted. Passive monitoring of the real traffic provides insight into the true communications requirements and the performance of a large number of inter-communicating nodes. It may be useful in identifying performance problems that are due to factors other than Internet congestion, especially when compared to other methods such as active monitoring where traffic is generated specifically to measure its performance. Controlled active monitoring between dedicated servers often gives an indication of what can be achieved on a network. Passive monitoring of the real traffic gives a picture of the true performance. The authors will discuss the method and results of collecting and analyzing flows of data obtained from the SLAC Internet border. The insights this has brought to understanding the network will be reviewed and the benefit it can bring to engineering networks will be discussed

Parameters of the SLAC Next Linear Collider

International Nuclear Information System (INIS)

Raubenheimer, T.; Adolphsen, C.; Burke, D.

1995-05-01

In this paper, the authors present the parameters and layout of the Next Linear Collider (NLC). The NLC is the SLAC design of a future linear collider using X-band RF technology in the main linacs. The collider would have an initial center-of-mass energy of 0.5 TeV which would be upgraded to 1 TeV and then 1.5 TeV in two stages. The design luminosity is > 5 x 10 33 cm -2 sec -1 at 0.5 TeV and > 10 34 cm -2 sec -1 at 1.0 and 1.5 TeV. They briefly describe the components of the collider and the proposed energy upgrade scenario

Performance of the SLAC Linear Collider klystrons

International Nuclear Information System (INIS)

Allen, M.A.; Fowkes, W.R.; Koontz, R.F.; Schwarz, H.D.; Seeman, J.T.; Vlieks, A.E.

1987-01-01

There are now 200 new, high power 5045 klystrons installed on the two-mile Stanford Linear Accelerator. Peak power per klystron averages over 63 MW. Average energy contribution is above 240 MeV per station. Electron beam energy has been measured as high as 53 GeV. Energy instability due to kylstron malfunction is less than 0.2%. The installed klystrons have logged over one million operating hours with close to 20,00 klystron hours cumulative operating time between failures. Data is being accumulated on klystron operation and failure modes with failure signatures starting to become apparent. To date, no wholesale failure modes have surfaced that would impair the SLAC linear Collider (SLC) program

Cerenkov ring imaging detector development at SLAC

International Nuclear Information System (INIS)

Williams, S.H.

1984-06-01

The imaging of Cerenkov light on to photosensitive detectors promises to be a powerful technique for identifying particles in colliding beam spectrometers. Toward this end two and three dimensional imaging photon detectors are being developed at SLAC. The present techniques involve photon conversion using easily ionized exotic chemicals like tetrakisdimethyl-amino-ethylene (TMAE) in a drift and amplifying gas mixture of methane and isobutane. Single photoelectrons from Cerenkov light are currently being drifted 20 cm and a new device under study will be used to study drifting up to 80 cm along a magnetic field. A short description of a large device currently being designed for the SLD spectrometer at the Stanford Linear Collider will be given

Facility for Advanced Accelerator Experimental Tests at SLAC (FACET) Conceptual Design Report

Energy Technology Data Exchange (ETDEWEB)

Amann, J.; Bane, K.; /SLAC

2009-10-30

This Conceptual Design Report (CDR) describes the design of FACET. It will be updated to stay current with the developing design of the facility. This CDR begins as the baseline conceptual design and will evolve into an 'as-built' manual for the completed facility. The Executive Summary, Chapter 1, gives an introduction to the FACET project and describes the salient features of its design. Chapter 2 gives an overview of FACET. It describes the general parameters of the machine and the basic approaches to implementation. The FACET project does not include the implementation of specific scientific experiments either for plasma wake-field acceleration for other applications. Nonetheless, enough work has been done to define potential experiments to assure that the facility can meet the requirements of the experimental community. Chapter 3, Scientific Case, describes the planned plasma wakefield and other experiments. Chapter 4, Technical Description of FACET, describes the parameters and design of all technical systems of FACET. FACET uses the first two thirds of the existing SLAC linac to accelerate the beam to about 20GeV, and compress it with the aid of two chicanes, located in Sector 10 and Sector 20. The Sector 20 area will include a focusing system, the generic experimental area and the beam dump. Chapter 5, Management of Scientific Program, describes the management of the scientific program at FACET. Chapter 6, Environment, Safety and Health and Quality Assurance, describes the existing programs at SLAC and their application to the FACET project. It includes a preliminary analysis of safety hazards and the planned mitigation. Chapter 7, Work Breakdown Structure, describes the structure used for developing the cost estimates, which will also be used to manage the project. The chapter defines the scope of work of each element down to level 3.

Facility for Advanced Accelerator Experimental Tests at SLAC (FACET) Conceptual Design Report

International Nuclear Information System (INIS)

Amann, J.; Bane, K.

2009-01-01

This Conceptual Design Report (CDR) describes the design of FACET. It will be updated to stay current with the developing design of the facility. This CDR begins as the baseline conceptual design and will evolve into an 'as-built' manual for the completed facility. The Executive Summary, Chapter 1, gives an introduction to the FACET project and describes the salient features of its design. Chapter 2 gives an overview of FACET. It describes the general parameters of the machine and the basic approaches to implementation. The FACET project does not include the implementation of specific scientific experiments either for plasma wake-field acceleration for other applications. Nonetheless, enough work has been done to define potential experiments to assure that the facility can meet the requirements of the experimental community. Chapter 3, Scientific Case, describes the planned plasma wakefield and other experiments. Chapter 4, Technical Description of FACET, describes the parameters and design of all technical systems of FACET. FACET uses the first two thirds of the existing SLAC linac to accelerate the beam to about 20GeV, and compress it with the aid of two chicanes, located in Sector 10 and Sector 20. The Sector 20 area will include a focusing system, the generic experimental area and the beam dump. Chapter 5, Management of Scientific Program, describes the management of the scientific program at FACET. Chapter 6, Environment, Safety and Health and Quality Assurance, describes the existing programs at SLAC and their application to the FACET project. It includes a preliminary analysis of safety hazards and the planned mitigation. Chapter 7, Work Breakdown Structure, describes the structure used for developing the cost estimates, which will also be used to manage the project. The chapter defines the scope of work of each element down to level 3.

Searching for light dark matter with the SLAC millicharge experiment.

Science.gov (United States)

Diamond, M; Schuster, P

2013-11-27

New sub-GeV gauge forces ("dark photons") that kinetically mix with the photon provide a promising scenario for MeV-GeV dark matter and are the subject of a program of searches at fixed-target and collider facilities around the world. In such models, dark photons produced in collisions may decay invisibly into dark-matter states, thereby evading current searches. We reexamine results of the SLAC mQ electron beam dump experiment designed to search for millicharged particles and find that it was strongly sensitive to any secondary beam of dark matter produced by electron-nucleus collisions in the target. The constraints are competitive for dark photon masses in the ~1-30 MeV range, covering part of the parameter space that can reconcile the apparent (g-2)(μ) anomaly. Simple adjustments to the original SLAC search for millicharges may extend sensitivity to cover a sizable portion of the remaining (g-2)(μ) anomaly-motivated region. The mQ sensitivity is therefore complementary to ongoing searches for visible decays of dark photons. Compared to existing direct-detection searches, mQ sensitivity to electron-dark-matter scattering cross sections is more than an order of magnitude better for a significant range of masses and couplings in simple models.

Review of light water reactor regulatory requirements: Assessment of selected regulatory requirements that may have marginal importance to risk: Postaccident sampling system, Turbine missiles, Combustible gas control, Charcoal filters

International Nuclear Information System (INIS)

Scott, W.B.; Jamison, J.D.; Stoetzel, G.A.; Tabatabai, A.S.; Vo, T.V.

1987-05-01

In a study commissioned by the Nuclear Regulatory Commission (NRC), Pacific Northwest Laboratory (PNL) evaluated the costs and benefits of modifying regulatory requirements in the areas of the postaccident sampling system, turbine rotor design reviews and inspections, combustible gas control for inerted Boiling Water Reactor (BWR) containments, and impregnated charcoal filters in certain plant ventilation systems. The basic framework for the analyses was that presented in the Regulatory Analysis Guidelines (NUREG/BR-0058) and in the Handbook for Value-Impact Assessment (NUREG/CR-3568). The effects of selected modifications to regulations were evaluated in terms of such factors as public risk and costs to industry and NRC. The results indicate that potential modifications of the regulatory requirements in three of the four areas would have little impact on public risk. In the fourth area, impregnated charcoal filters in building ventilation systems do appear to limit risks to the public and plant staff. Revisions in the severe accident source term assumptions, however, may reduce the theoretical value of charcoal filters. The cost analysis indicated that substantial savings in operating costs may be realized by changing the interval of turbine rotor inspections. Small to moderate operating cost savings may be realized through postulated modifications to the postaccident sampling system requirements and to the requirements for combustible gas control in inerted BWR containments. Finally, the use of impregnated charcoal filters in ventilation systems appears to be the most cost-effective method of reducing radioiodine concentrations

Data Quality Objectives for Regulatory Requirements for Hazardous and Radioactive Air Emissions Sampling and Analysis

International Nuclear Information System (INIS)

MULKEY, C.H.

1999-01-01

This document describes the results of the data quality objective (DQO) process undertaken to define data needs for state and federal requirements associated with toxic, hazardous, and/or radiological air emissions under the jurisdiction of the River Protection Project (RPP). Hereafter, this document is referred to as the Air DQO. The primary drivers for characterization under this DQO are the regulatory requirements pursuant to Washington State regulations, that may require sampling and analysis. The federal regulations concerning air emissions are incorporated into the Washington State regulations. Data needs exist for nonradioactive and radioactive waste constituents and characteristics as identified through the DQO process described in this document. The purpose is to identify current data needs for complying with regulatory drivers for the measurement of air emissions from RPP facilities in support of air permitting. These drivers include best management practices; similar analyses may have more than one regulatory driver. This document should not be used for determining overall compliance with regulations because the regulations are in constant change, and this document may not reflect the latest regulatory requirements. Regulatory requirements are also expected to change as various permits are issued. Data needs require samples for both radionuclides and nonradionuclide analytes of air emissions from tanks and stored waste containers. The collection of data is to support environmental permitting and compliance, not for health and safety issues

Guidance and methods for satisfying low specific activity material and surface contaminated object regulatory requirements

International Nuclear Information System (INIS)

Pope, R.B.; Shappert, L.B.; Michelhaugh, R.D.; Boyle, R.W.; Easton, E.P.; Coodk, J.R.

1998-01-01

The U.S. Department of Transportation (DOT) and the U.S. Nuclear Regulatory Commission (NRC) have prepared a comprehensive set of draft guidance for shippers and inspectors to use when applying the newly imposed regulatory requirements for low specific activity (LSA) material and surface contaminated objects (SCOs). These requirements represent significant departures in some areas from the manner in which these materials and objects were regulated by the earlier versions of the regulations. The proper interpretation and application of the regulatory criteria can require a fairly complex set of decisions be made. To assist those trying these regulatory requirements, a detailed set of logic-flow diagrams representing decisions related to multiple factors were prepared and included in the draft report for comment on Categorizing and Transporting Low Specific Activity Materials and Surface Contaminated Objects, (DOT/NRC, 1997). These logic-flow diagrams, as developed, are specific to the U.S. regulations, but were readily adaptable to the IAEA regulations. The diagrams have been modified accordingly and tied directly to specific paragraphs in IAEA Safety Series No. 6. This paper provides the logic-flow diagrams adapted in the IAEA regulations, and demonstrated how these diagrams can be used to assist consignors and inspectors in assessing compliance of shipments with the LSA material and SCO regulatory requirements. (authors)

Reconstitution of CO2 Regulation of SLAC1 Anion Channel and Function of CO2-Permeable PIP2;1 Aquaporin as CARBONIC ANHYDRASE4 Interactor

Science.gov (United States)

Zeise, Brian; Xu, Danyun; Rappel, Wouter-Jan; Boron, Walter F.; Schroeder, Julian I.

2016-01-01

Dark respiration causes an increase in leaf CO2 concentration (Ci), and the continuing increases in atmospheric [CO2] further increases Ci. Elevated leaf CO2 concentration causes stomatal pores to close. Here, we demonstrate that high intracellular CO2/HCO3− enhances currents mediated by the Arabidopsis thaliana guard cell S-type anion channel SLAC1 upon coexpression of any one of the Arabidopsis protein kinases OST1, CPK6, or CPK23 in Xenopus laevis oocytes. Split-ubiquitin screening identified the PIP2;1 aquaporin as an interactor of the βCA4 carbonic anhydrase, which was confirmed in split luciferase, bimolecular fluorescence complementation, and coimmunoprecipitation experiments. PIP2;1 exhibited CO2 permeability. Mutation of PIP2;1 in planta alone was insufficient to impair CO2- and abscisic acid-induced stomatal closing, likely due to redundancy. Interestingly, coexpression of βCA4 and PIP2;1 with OST1-SLAC1 or CPK6/23-SLAC1 in oocytes enabled extracellular CO2 enhancement of SLAC1 anion channel activity. An inactive PIP2;1 point mutation was identified that abrogated water and CO2 permeability and extracellular CO2 regulation of SLAC1 activity. These findings identify the CO2-permeable PIP2;1 as key interactor of βCA4 and demonstrate functional reconstitution of extracellular CO2 signaling to ion channel regulation upon coexpression of PIP2;1, βCA4, SLAC1, and protein kinases. These data further implicate SLAC1 as a bicarbonate-responsive protein contributing to CO2 regulation of S-type anion channels. PMID:26764375

Research and development toward a 4.5-1.5{angstrom} linac coherent light source (LCLS) at SLAC

Energy Technology Data Exchange (ETDEWEB)

Tatchyn, R.; Arthur, J.; Baltay, M. [Stanford Univ., CA (United States)] [and others

1995-12-31

In recent years significant studies have been initiated on the theoretical and technical feasibility of utilizing a portion of the 3km S-band accelerator at the Stanford Linear Accelerator Center (SLAC) to drive a short wavelength (4.5-1.5 {Angstrom}) Linac Coherent Light Source (LCLS), a Free-Electron Laser (FEL) operating in the Self-Amplified Spontaneous Emission (SASE) regime. Electron beam requirements for single-pass saturation include: (1) a peak current in the 3-7 kA range, (2) a relative energy spread of <0.05%, ad (3) a transverse emittance, {epsilon}{le}{lambda}/4{pi}, where {lambda}[m] is the output wavelength. Requirements on the insertion device include field error levels of 0.1-0.2% for keeping the electron bunch centered on and in phase with the amplified photons, and a focusing beta of 4-8 m for inhibiting the dilution of its transverse density. Although much progress techniques necessary for LCLS operation down to {approximately}20 {angstrom}, a substantial amount of research and development is still required in a number of theoretical and experimental areas leading to the construction and operation of a 4.5-1.5 {angstrom} LCLS. In this paper we report on a research and development program underway and in planning at SLAC for addressing critical questions in these areas. These include the construction and operation of a linac test stand for developing laser-driven photocathode rf guns with normalized emittances approaching 1 mm-mr; development of advanced beam compression, stability, an emittance control techniques at multi-GeV energies; the construction and operation of a FEL Amplifier Test Experiment (FATE) for theoretical and experimental studies of SASE at IR wavelengths; an undulator development program to investigate superconducting, hybrid/permanent magnet (hybrid/PM), and pulsed-Cu technologies; theoretical and computational studies of high-gain FEL physics and LCLS component designs.

Development of safety-related regulatory requirements for nuclear power in developing countries. Key issue paper no. 4

International Nuclear Information System (INIS)

Han, K.I.

2000-01-01

In implementing a national nuclear power program, balanced regulatory requirements are necessary to ensure nuclear safety and cost competitive nuclear power, and to help gain public acceptance. However, this is difficult due to the technology-intensive nature of the nuclear regulatory requirements, the need to reflect evolving technology and the need for cooperation among multidisciplinary technical groups. This paper suggests approaches to development of balanced nuclear regulatory requirements in developing countries related to nuclear power plant safety, radiation protection and radioactive waste management along with key technical regulatory issues. It does not deal with economic or market regulation of electric utilities using nuclear power. It suggests that national regulatory requirements be developed using IAEA safety recommendations as guidelines and safety requirements of the supplier country as a main reference after careful planning, manpower buildup and thorough study of international and supplier country's regulations. Regulation making is not recommended before experienced manpower has been accumulated. With an option that the supplier country's regulations may be used in the interim, the lack of complete national regulatory requirements should not deter introduction of nuclear power in developing countries. (author)

Final Report: BaBar Detector and Experimental at SLAC, September 30, 1998 - September 29, 1999

International Nuclear Information System (INIS)

Judd, Dennis J.

2000-01-01

The Prairie View AandM University High Energy Physics Group with its contingent of three undergraduates physics majors, joined the BaBar Collaboration at SLAC in September 1994. BaBar is the experiment and detector running in the PEP-II ring at SLAC as part of the Asymmetric B Factory project there to study CP violation and heavy flavor physics. The focus of our effort before this year was with the Muon/Neutral Hadron Detector/Instrumented Flux Return (IFD) subgroup within the BaBar collaboration, and particularly with the GEANT simulation of the IFR-. With the GEANT3 simulation essentially FR-ozen, and the GEANT4 full simulation of the IFR- done, we have decided to redirect our efforts toward other areas

Final Report BaBar Detector and Experimental at SLAC, September 30, 1998 - September 29, 1999

CERN Document Server

Judd, D J

2000-01-01

The Prairie View AandM University High Energy Physics Group with its contingent of three undergraduates physics majors, joined the BaBar Collaboration at SLAC in September 1994. BaBar is the experiment and detector running in the PEP-II ring at SLAC as part of the Asymmetric B Factory project there to study CP violation and heavy flavor physics. The focus of our effort before this year was with the Muon/Neutral Hadron Detector/Instrumented Flux Return (IFD) subgroup within the BaBar collaboration, and particularly with the GEANT simulation of the IFR-. With the GEANT3 simulation essentially FR-ozen, and the GEANT4 full simulation of the IFR- done, we have decided to redirect our efforts toward other areas.

Governmental, Legal and Regulatory Framework for Safety. General Safety Requirements. Part 1

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-09-15

The objective of this publication is to establish requirements in respect of the governmental, legal and regulatory framework for safety. It covers the essential aspects of the framework for establishing a regulatory body and taking other actions necessary to ensure the effective regulatory control of facilities and activities utilized for peaceful purposes. Other responsibilities and functions, such as liaison within the global safety regime and on support services for safety (including radiation protection), emergency preparedness and response, nuclear security, and the State system of accounting for and control of nuclear material, are also covered.

SLC status and SLAC future plans

International Nuclear Information System (INIS)

Richter, B.

1990-01-01

In this presentation, I shall discuss the linear collider program at the Stanford Linear Accelerator Center as it is now, and as we hope to see it evolve over the next few years. Of greatest interest to the high-energy accelerator physics community gathered here is the development of the linear collider concept, and so I shall concentrate most of this paper on a discussion of the present status and future evolution of the SLC. I will also briefly discuss the research and development program that we are carrying out aimed at the realization of the next generation of higher-energy linear colliders. SLAC has a major colliding-beam storage-ring program as well, including present rings and design studies on future high luminosity projects, but time constraints preclude a discussion of them. (author) 8 figs., 3 tabs

Annual Site Environmental Report: 2006

Energy Technology Data Exchange (ETDEWEB)

Nuckolls, H.; /SLAC

2008-02-22

This report provides information about environmental programs during the calendar year (CY) of 2006 at the Stanford Linear Accelerator Center (SLAC), Menlo Park, California. Activities that span the calendar year; i.e., stormwater monitoring covering the winter season of 2006/2007 (October 2006 through May 2007), are also included. Production of an annual site environmental report (ASER) is a requirement established by the United States Department of Energy (DOE) for all management and operating (M&O) contractors throughout the DOE complex. SLAC is a federally-funded research and development center with Stanford University as the M&O contractor. SLAC continued to follow the path to self-declare an environmental management system under DOE Order 450.1, 'Environmental Protection Program' and effectively applied environmental management in meeting the site's integrated safety and environmental management system goals. For normal daily activities, all SLAC managers and supervisors are responsible for ensuring that proper procedures are followed so that Worker safety and health are protected; The environment is protected; and Compliance is ensured. Throughout 2006, SLAC focused on these activities through the SLAC management systems. These systems were also the way SLAC approached implementing 'greening of the government' initiatives such as Executive Order 13148. The management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. The SLAC Office of Assurance was created during 2006 in response to DOE Order 226.1. During 2006, there were no reportable releases to the environment from SLAC operations, and there were no Notice of Violations issued to SLAC from any of the regulatory agencies that oversee SLAC. In addition, many improvements in waste minimization, recycling, stormwater drain system, groundwater restoration, and SLAC's chemical management system (CMS) were continued during

An evaluation model for the definition of regulatory requirements on spent fuel pool cooling systems

International Nuclear Information System (INIS)

Izquierdo, J.M.

1979-01-01

A calculation model is presented for establishing regulatory requirements in the SFPCS System. The major design factors, regulatory and design limits and key parameters are discussed. A regulatory position for internal use is proposed. Finally, associated problems and experience are presented. (author)

Measurements of the Z boson resonance parameters at SLC [SLAC Linear Collider

International Nuclear Information System (INIS)

Hearty, C.

1989-07-01

This paper presents the measurement by the Mark II experiment at the SLAC Linear Collider of the parameters of the Z boson resonance. The results are updated from those presented at the SLAC Summer Institute to include all data presented in the most recent Mark II publication, consisting of 19 nb -1 of data at ten different center-of-mass energies between 89.2 and 93.0 GeV. The resonance parameters are extracted by measuring the Z production cross section at a series of center-of-mass energies (scan points) near the Z peak, then fitting these data with the theoretical cross section. The four major aspects of the analysis are the determination at each scan point of the center-of-mass energy (E), the integrated luminosity, the number of Z decays and the expected cross section as a function of the resonance parameters, such as mass and width. I will discuss each of these steps in turn, after a brief description of the Mark II detector, then conclude with the results of the analysis. 7 refs., 9 figs., 3 tabs

Economic analysis requirements in support of orbital debris regulatory policy

Science.gov (United States)

Greenberg, Joel S.

1996-10-01

As the number of Earth orbiting objects increases so does the potential for generating orbital debris with the consequent increase in the likelihood of impacting and damaging operating satellites. Various debris remediation approaches are being considered that encompass both in-orbit and return-to-Earth schema and have varying degrees of operations, cost, international competitiveness, and safety implications. Because of the diversity of issues, concerns and long-term impacts, there is a clear need for the setting of government policies that will lead to an orderly abatement of the potential orbital debris hazards. These policies may require the establishment of a supportive regulatory regime. The Department of Transportation is likely to have regulatory responsibilities relating to orbital debris stemming from its charge to protect the public health and safety, safety of property, and national security interests and foreign policy interests of the United States. This paper describes DOT's potential regulatory role relating to orbital debris remediation, the myriad of issues concerning the need for establishing government policies relating to orbital debris remediation and their regulatory implications, the proposed technological solutions and their economic and safety implications. Particular emphasis is placed upon addressing cost-effectiveness and economic analyses as they relate to economic impact analysis in support of regulatory impact analysis.

Survey of extreme load design regulatory agency licensing requirements for nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Stevenson, J D

1976-04-01

Since 1965, when extreme load requirements began to be considered explicitly in nuclear power plant design, there has been a gradual divergence in requirements imposed by national regulatory agencies. However, nuclear plant safety is an international problem because of the potential international effects of any postulated plant failure. For this reason this paper has been prepared in an attempt to highlight the differences in national criteria currently used in the extreme load design of nuclear plant facilities. No attempt has been made to evaluate the relative merit of the criteria established by the various national regulatory agencies. This paper presents the results of a recent survey made of national atomic energy regulatory agencies and major nuclear steam supply design agencies, which requested a summary of current licensing criteria associated with earthquake, extreme wind (tornado), flood, airplane crash and accident (pipe break) loads applicable within the various national jurisdictions. Also presented are a number of comparisons which are meant to illustrate the differences in national regulatory criteria.

Survey of extreme load design regulatory agency licensing requirements for nuclear power plants

International Nuclear Information System (INIS)

Stevenson, J.D.

1976-01-01

Since 1965, when extreme load requirements began to be considered explicitly in nuclear power plant design, there has been a gradual divergence in requirements imposed by national regulatory agencies. However, nuclear plant safety is an international problem because of the potential international effects of any postulated plant failure. For this reason this paper has been prepared in an attempt to highlight the differences in national criteria currently used in the extreme load design of nuclear plant facilities. No attempt has been made to evaluate the relative merit of the criteria established by the various national regulatory agencies. This paper presents the results of a recent survey made of national atomic energy regulatory agencies and major nuclear steam supply design agencies, which requested a summary of current licensing criteria associated with earthquake, extreme wind (tornado), flood, airplane crash and accident (pipe break) loads applicable within the various national jurisdictions. Also presented are a number of comparisons which are meant to illustrate the differences in national regulatory criteria. (Auth.)

Measurements of ultimate accelerating gradients in the SLAC disk-loaded structure. Part I

International Nuclear Information System (INIS)

Wang, J.W.; Loew, G.A.

1985-01-01

The work reported here describes measurements made to study the maximum attainable accelerating gradients in a conventional SLAC disk-loaded accelerator section of the constant-gradient type running at 2856 MHz. The objective was to reach an accelerating gradient of at least 100 MV/m. The accelerating gradient at which the SLAC disk-loaded waveguide runs routinely is approx. 9 MV/m (36 MW tubes without SLED) and approx. 12 MV/m with SLED I (2.5 μsec pulse). To reach 100 MV/m in a conventional 3 m constant-gradient section, one would need a klystron with a peak power output of 900 MW. since such a tube is not available, we decided to use a short standing-wave section in which the resonant fields would be allowed to build up. The design criteria for this section, the fabrication, matching and tuning, the experimental set-up and the results are described below

SLAC divertor channel entrance thermal stress analysis

International Nuclear Information System (INIS)

Johnson, G.L.; Stein, W.; Lu, S.C.; Riddle, R.A.

1985-01-01

X-ray beams emerging from the new SLAC electron-positron storage ring (PEP) impinge on the entrance to tangential divertor channels causing highly localized heating in the channel structure. Analyses were completed to determine the temperatures and thermally-induced stresses due to this heating. These parts are cooled with water flowing axially over them at 30 0 C. The current design and operating conditions should result in the entrance to the new divertor channel operating at a peak temperature of 123 0 C with a peak thermal stress at 91% of yield. Any micro-cracks that form due to thermally-induced stresses should not propagate to the coolant wall nor form a path for the coolant to leak into the storage ring vacuum. 34 figs., 4 tabs

Licensing evaluation of CANDU-PHW nuclear power plants relative to U.S. regulatory requirements

International Nuclear Information System (INIS)

Erp, J.B. van

1978-01-01

Differences between the U.S. and Canadian approach to safety and licensing are discussed. U.S. regulatory requirements are evaluated as regards their applicability to CANDU-PHW reactors; vice-versa the CANDU-PHW reactor is evaluated with respect to current Regulatory Requirements and Guides. A number of design modifications are proposed to be incorporated into the CANDU-PHW reactor in order to facilitate its introduction into the U.S. These modifications are proposed solely for the purpose of maintaining consistency within the current U.S. regulatory system and not out of a need to improve the safety of current-design CANDU-PHW nuclear power plants. A number of issues are identified which still require resolution. Most of these issues are concerned with design areas not (yet) covered by the ASME code. (author)

Using the SLAC VHF and UHF radio systems

International Nuclear Information System (INIS)

Struven, W.

1987-02-01

The use of the SLAC VHF and UHF Radio Systems and the Tunnel Antenna Systems as they are presently configured is described. The original radio system was built in 1966 and has grown in scope over the years. The Tunnel Antenna Systems were developed for, and first installed in, the PEP ring, and later added to other tunnels and redesigned to cover the UHF range, as well as VHF. The UHF radio system was designed and built for SLC use, and was first used in the SLC Arcs. The three radio systems will be described and the capabilities of each system will be defined

Annual Site Environmental Report: 2003

Energy Technology Data Exchange (ETDEWEB)

Nuckolls, H.; /SLAC

2006-04-19

This report provides information about environmental programs during 2003 at the Stanford Linear Accelerator Center (SLAC). Seasonal activities that span calendar years are also included. Production of an annual site environmental report (ASER) is a requirement established by the DOE for all management and operating (M&O) contractors throughout the DOE complex. This summary demonstrates the effective application of SLAC environmental management to meet the site's integrated safety management system (ISMS) goals. For normal daily activities, all SLAC managers and supervisors are responsible for ensuring proper procedures are followed so that worker safety and health are protected; the environment is protected; and compliance is ensured. Throughout 2003, SLAC focused on these activities through the SLAC management systems (described in Chapter 3). These systems were utilized by SLAC to implement such ''greening of the government'' initiatives like Executive Order 13148. The management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. There were no reportable releases to the environment from SLAC operations during 2003. In addition, many improvements were continued during 2003 in waste minimization, recycling, decreasing air emission rates, stormwater drain system, groundwater restoration, and planning for a system to better manage chemical use. Program-specific details discussed are: (1) Air Quality--SLAC operates its air quality management program in compliance with established permit conditions; 2003 was the sixth consecutive year the air quality management program operated without any NOVs issued by regulators. Nevertheless, SLAC has an active program to improve its environmental performance in air quality. (2) Hazardous Waste--The Environmental Health Division of the San Mateo County Health Services Agency is the California certified unified permitting agency (CUPA) responsible

Annual Site Environmental Report, 2004

Energy Technology Data Exchange (ETDEWEB)

Nuckolls, H.; /SLAC

2006-04-19

This report provides information about environmental programs during 2004 at the Stanford Linear Accelerator Center (SLAC). Seasonal activities that span calendar years are also included. Production of an annual site environmental report (ASER) is a requirement established by the United States Department of Energy (DOE) for all management and operating (M&O) contractors throughout the DOE complex. SLAC is a federally-funded, research and development center with Stanford University as the M&O contractor. The most noteworthy information in this report is summarized in this section. This summary demonstrates the effective application of SLAC environmental management in meeting the site's integrated safety management system (ISMS) goals. For normal daily activities, all SLAC managers and supervisors are responsible for ensuring that proper procedures are followed so that worker safety and health are protected; the environment is protected; and compliance is ensured. Throughout 2004, SLAC focused on these activities through the SLAC management systems (described in Chapter 3). These systems were also the way SLAC approached implementing ''greening of the government'' initiatives such as Executive Order 13148. The management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. There were no reportable releases to the environment from SLAC operations during 2004. In addition, many improvements were continued during 2004, in waste minimization, recycling, decreasing air emission rates, stormwater drain system, groundwater restoration, and planning for a chemical management system to manage chemical use better. Program-specific details discussed are: (1) Air Quality--SLAC operates its air quality management program in compliance with its established permit conditions: 2004 was the seventh consecutive year the air quality management program operated without receiving any notices of violation

Preliminary Conceptual Design Report for the FACET-II Project at SLAC National Accelerator Laboratory

Energy Technology Data Exchange (ETDEWEB)

Hogan, Mark [SLAC National Accelerator Lab., Menlo Park, CA (United States)

2016-04-22

Plasma wakefield acceleration has the potential to dramatically shrink the size and cost of particle accelerators. Research at the SLAC National Accelerator Laboratory has demonstrated that plasmas can provide 1,000 times the acceleration in a given distance compared with current technologies. Developing revolutionary and more efficient acceleration techniques that allow for an affordable high-energy collider is the focus of FACET, a National User Facility at SLAC. The existing FACET National User Facility uses part of SLAC’s two-mile-long linear accelerator to generate high-density beams of electrons and positrons. FACET-II is a new test facility to develop advanced acceleration and coherent radiation techniques with high-energy electron and positron beams. It is the only facility in the world with high energy positron beams. FACET-II provides a major upgrade over current FACET capabilities and the breadth of the potential research program makes it truly unique. It will synergistically pursue accelerator science that is vital to the future of both advanced acceleration techniques for High Energy Physics, ultra-high brightness beams for Basic Energy Science, and novel radiation sources for a wide variety of applications. The design parameters for FACET-II are set by the requirements of the plasma wakefield experimental program. To drive the plasma wakefield requires a high peak current, in excess of 10kA. To reach this peak current, the electron and positron design bunch size is 10μ by 10μ transversely with a bunch length of 10μ. This is more than 200 times better than what has been achieved at the existing FACET. The beam energy is 10 GeV, set by the Linac length available and the repetition rate is up to 30 Hz. The FACET-II project is scheduled to be constructed in three major stages. Components of the project discussed in detail include the following: electron injector, bunch compressors and linac, the positron system, the Sector 20 sailboat and W chicanes

An S-type anion channel SLAC1 is involved in cryptogein-induced ion fluxes and modulates hypersensitive responses in tobacco BY-2 cells.

Science.gov (United States)

Kurusu, Takamitsu; Saito, Katsunori; Horikoshi, Sonoko; Hanamata, Shigeru; Negi, Juntaro; Yagi, Chikako; Kitahata, Nobutaka; Iba, Koh; Kuchitsu, Kazuyuki

2013-01-01

Pharmacological evidence suggests that anion channel-mediated plasma membrane anion effluxes are crucial in early defense signaling to induce immune responses and hypersensitive cell death in plants. However, their molecular bases and regulation remain largely unknown. We overexpressed Arabidopsis SLAC1, an S-type anion channel involved in stomatal closure, in cultured tobacco BY-2 cells and analyzed the effect on cryptogein-induced defense responses including fluxes of Cl(-) and other ions, production of reactive oxygen species (ROS), gene expression and hypersensitive responses. The SLAC1-GFP fusion protein was localized at the plasma membrane in BY-2 cells. Overexpression of SLAC1 enhanced cryptogein-induced Cl(-) efflux and extracellular alkalinization as well as rapid/transient and slow/prolonged phases of NADPH oxidase-mediated ROS production, which was suppressed by an anion channel inhibitor, DIDS. The overexpressor also showed enhanced sensitivity to cryptogein to induce downstream immune responses, including the induction of defense marker genes and the hypersensitive cell death. These results suggest that SLAC1 expressed in BY-2 cells mediates cryptogein-induced plasma membrane Cl(-) efflux to positively modulate the elicitor-triggered activation of other ion fluxes, ROS as well as a wide range of defense signaling pathways. These findings shed light on the possible involvement of the SLAC/SLAH family anion channels in cryptogein signaling to trigger the plasma membrane ion channel cascade in the plant defense signal transduction network.

Accelerator structure bead pull measurement at SLAC

CERN Document Server

Lewandowski, J R; Miller, R H; Wang, J W

2004-01-01

Microwave measurement and tuning of accelerator structures are important issues for the current and next generation of high energy physics machines. Application of these measurements both before and after high power processing can reveal information about the structure but may be misinterpreted if measurement conditions are not carefully controlled. For this reason extensive studies to characterize the microwave measurements at have been made at SLAC. For the beadpull a reproducible measurement of less than 1 degree of phase accuracy in total phase drift is needed in order to resolve issues such as phase changes due to structure damage during high power testing. Factors contributing to measurement errors include temperature drift, mechanical vibration, and limitations of measurement equipment such as the network analyzer. Results of this continuing effort will be presented.

SLAC linear collider and a few ideas on future linear colliders

International Nuclear Information System (INIS)

Loew, G.A.

1984-04-01

This paper comes in two parts. The first part is a progress report on the SLAC Linear Collider (SLC) with emphasis on those systems which are of special interest to linear accelerator designers; it sets the stage for a number of contributed papers on specific topics which are also presented at this conference. The second part presents some ideas which are of interest to the design of future linear colliders of higher energies

Regulatory requirements for radiation protection

International Nuclear Information System (INIS)

Mason, E.A.; Cunningham, R.E.; Hard, J.E.; Mattson, R.J.; Smith, R.D.; Peterson, H.T. Jr.

1977-01-01

Regulatory requirements for radiation protection have evolved and matured over several decades. Due to the wide adoption of recommendations of the International Commission on Radiation Protection (ICRP), there exists international agreement on the principles to be followed for radiation protection. This foundation will be increasingly important due to the growing need for international agreements and standards for radiation protection and radioactive materials management. During the infancy of the commercial nuclear industry, primary reliance was placed on the protection of the individual, both in the work force and as a member of the public. With the growth of nuclear power in the 1960's and 1970's, environmental impact assessments and expert reviews of bio-effects data have focused attention on statistical risks to large population groups and the use of the collective dose commitment concept to estimate potential effects. The potential release of long-lived radionuclides from the nuclear fuel cycle requires further consideration of radionuclide accumulation in the biosphere and calls for controls conceived and implemented at the international level. The initial development efforts for addressing these concerns already have been instituted by the ICRP and the IAEA. However, formal international agreements and a unified set of international standards may be required to implement the recommendations of these groups. Further international efforts in the field of radiation protection are also called for in developing waste management practices and radioactive effluent control technology, in site selection for fuel reprocessing plants and waste dispersal facilities, and for ensuring safe transport of high-level wastes in various forms. Since the regulation of very low dose rates and doses will be involved, it will be useful to reexamine dose-effect relationships and societal goals for health protection. Improved criteria and methodologies for ''as low as readily

Data Quality Objectives for Regulatory Requirements for Hazardous and Radioactive Air Emissions Sampling and Analysis

Energy Technology Data Exchange (ETDEWEB)

MULKEY, C.H.

1999-07-06

This document describes the results of the data quality objective (DQO) process undertaken to define data needs for state and federal requirements associated with toxic, hazardous, and/or radiological air emissions under the jurisdiction of the River Protection Project (RPP). Hereafter, this document is referred to as the Air DQO. The primary drivers for characterization under this DQO are the regulatory requirements pursuant to Washington State regulations, that may require sampling and analysis. The federal regulations concerning air emissions are incorporated into the Washington State regulations. Data needs exist for nonradioactive and radioactive waste constituents and characteristics as identified through the DQO process described in this document. The purpose is to identify current data needs for complying with regulatory drivers for the measurement of air emissions from RPP facilities in support of air permitting. These drivers include best management practices; similar analyses may have more than one regulatory driver. This document should not be used for determining overall compliance with regulations because the regulations are in constant change, and this document may not reflect the latest regulatory requirements. Regulatory requirements are also expected to change as various permits are issued. Data needs require samples for both radionuclides and nonradionuclide analytes of air emissions from tanks and stored waste containers. The collection of data is to support environmental permitting and compliance, not for health and safety issues. This document does not address health or safety regulations or requirements (those of the Occupational Safety and Health Administration or the National Institute of Occupational Safety and Health) or continuous emission monitoring systems. This DQO is applicable to all equipment, facilities, and operations under the jurisdiction of RPP that emit or have the potential to emit regulated air pollutants.

Data Quality Objectives for Regulatory Requirements for Hazardous and Radioactive Air Emissions Sampling and Analysis

International Nuclear Information System (INIS)

MULKEY, C.H.

1999-01-01

This document describes the results of the data quality objective (DQO) process undertaken to define data needs for state and federal requirements associated with toxic, hazardous, and/or radiological air emissions under the jurisdiction of the River Protection Project (RPP). Hereafter, this document is referred to as the Air DQO. The primary drivers for characterization under this DQO are the regulatory requirements pursuant to Washington State regulations, that may require sampling and analysis. The federal regulations concerning air emissions are incorporated into the Washington State regulations. Data needs exist for nonradioactive and radioactive waste constituents and characteristics as identified through the DQO process described in this document. The purpose is to identify current data needs for complying with regulatory drivers for the measurement of air emissions from RPP facilities in support of air permitting. These drivers include best management practices; similar analyses may have more than one regulatory driver. This document should not be used for determining overall compliance with regulations because the regulations are in constant change, and this document may not reflect the latest regulatory requirements. Regulatory requirements are also expected to change as various permits are issued. Data needs require samples for both radionuclides and nonradionuclide analytes of air emissions from tanks and stored waste containers. The collection of data is to support environmental permitting and compliance, not for health and safety issues. This document does not address health or safety regulations or requirements (those of the Occupational Safety and Health Administration or the National Institute of Occupational Safety and Health) or continuous emission monitoring systems. This DQO is applicable to all equipment, facilities, and operations under the jurisdiction of RPP that emit or have the potential to emit regulated air pollutants

Electron Bunch Length Measurement for LCLS at SLAC

International Nuclear Information System (INIS)

Zelazny, M.; Allison, S.; Chevtsov, Sergei; Emma, P.; Kotturi, K.d.; Loos, H.; Peng, S.; Rogind, D.; Straumann, T.

2007-01-01

At Stanford Linear Accelerator Center (SLAC) a Bunch Length Measurement system has been developed to measure the length of the electron bunch for its new Linac Coherent Light Source (LCLS). This destructive measurement uses a transverse-mounted RF deflector (TCAV) to vertically streak the electron beam and an image taken with an insertable screen and a camera. The device control software was implemented with the Experimental Physics and Industrial Control System (EPICS) toolkit. The analysis software was implemented in Matlab(trademark) using the EPICS/Channel Access Interface for Scilab(trademark) and Matlab(trademark) (labCA). This architecture allowed engineers and physicists to develop and integrate their control and analysis without duplication of effort

Commissioning and operation of the nuclear physics injector at SLAC

International Nuclear Information System (INIS)

Koontz, R.F.; Iverson, R.; Leyer, G.K.; Miller, R.H.

1985-01-01

The new Nuclear Physics Injector (NPI) approved for construction in October of 1983 was completed by September of 1984, and delivered short pulse beams for SPEAR ring checkout in mid-October. Long pulse beams of up to 1.6 microsecond length were also demonstrated. The paper describes the startup operation, reviews the performance characteristics, and discusses the beam transport optics used to deliver 1 to 4 GeV beams to nuclear physics experiments in End Station A. The SLAC Nuclear Physics Injector is in full operationexclamation

Commissioning and operation of the nuclear physics injector at SLAC

International Nuclear Information System (INIS)

Koontz, R.F.; Miller, R.H.; Leger, G.K.; Iverson, R.

1985-01-01

The new Nuclear Physics Injector (NPI) approved for construction in October of 1983 was completed by September of 1984, and delivered short pulse beams for SPEAR ring checkout in mid-October. Long pulse beams of up to 1.6 microsecond length were also demonstrated. The paper describes the start-up operation, reviews the performance characteristics, and discusses the beam transport optics used to deliver 1 to 4 GeV beams to nuclear physics experiments in End Station A. The SLAC Nuclear Physics Injector is in full operation!

Regulatory requirement of the Juragua nuclear Power Plant PSA

International Nuclear Information System (INIS)

Valhuerdi Debesa, C.

1996-01-01

Probabilistic Safety Assessment has proved to be a powerful tool for improving the knowledge of the safety insides of Nuclear Power Plants and increasing the efficiency of the safety measures adopted by both operators and regulators. In this paper the regulatory approach adopted in Cuba with regard to the PSA , the scope of the requirement and the basis and proposal of this decision are presented

600 kV modulator design for the SLAC Next Linear Collider Test Accelerator

International Nuclear Information System (INIS)

Harris, K.; de Lamare, J.; Nesterov, V.; Cassel, R.

1992-07-01

Preliminary design for the SLAC Next Linear Collider Test Accelerator (NLCTA) requires a pulse power source to produce a 600 kV, 600 A, 1.4 μs, 0.1% flat top pulse with rise and fall times of approximately 100 ns to power an X-Band klystron with a microperveance of 1.25 at ∼ 100 MW peak RF power. The design goals for the modulator, including those previously listed, are peak modulator pulse power of 340 MW operating at 120 Hz. A three-stage darlington pulse-forming network, which produces a >100 kV, 1.4 μs pulse, is coupled to the klystron load through a 6:1 pulse transformer. Careful consideration of the transformer leakage inductance, klystron capacitance, system layout, and component choice is necessary to produce the very fast rise and fall times at 600 kV operating continuously at 120 Hz

Continuing education requirements among State Occupational Therapy Regulatory Boards in the United States of America

Directory of Open Access Journals (Sweden)

Savannah R. Hall

2016-10-01

Full Text Available Purpose The purpose of this study is to compare and contrast the contents of each state’s occupational therapy (OT regulatory board requirements regarding licensees’ acquisition of continuing education units in the United States of America. Methods Data related to continuing education requirements from each OT regulatory board of all 50 states and the District of Columbia in the United States were reviewed and categorized by two reviewers. Analysis was conducted based on the categorization of the continuing education requirements and activities required, allowed, and not allowed/not mentioned for continuing education units. Results Findings revealed non-uniformity and inconsistency of continuing education requirements for licensure renewal between OT regulatory boards and was coupled with lack of specific criteria for various continuing education activities. Continuing education requirements were not tailored to meet the needs of individual licensee’s current and anticipated professional role and job responsibilities, with a negative bias towards presentation and publication allowed for continuing education units. Few boards mandated continuing education topics on ethics related to OT practice within each renewal cycle. Conclusion OT regulatory boards should move towards unifying the reporting format of continuing education requirements across all states to reduce ambiguity and to ensure licensees are equipped to provide ethical and competent practice. Efforts could be made to enact continuing education requirements specific to the primary role of a particular licensee. Finally, assigning the amount of continuing education credits to be awarded for different activities should be based on research evidence rather than arbitrary determination.

Information management systems for integrating the technical data and regulatory requirements of environmental restoration activities

International Nuclear Information System (INIS)

Geffen, C.A.; Garrett, B.A.; Walter, M.B.

1990-03-01

Current environmental regulations require that comprehensive planning be conducted before remediating a hazardous waste site to characterize the nature and extent of site contamination, calculate the risk to the public, and assess the effectiveness of various remediation technologies. Remediation of Department of Energy (DOE) sites contaminated with hazardous or mixed wastes will require the effective integration of scientific and engineering data with regulatory and institutional requirements. The information management challenge presented by waste site cleanup activities goes beyond merely dealing with the large quantity of data that will be generated. The information must be stored, managed, and presented in a way that provides some consistency in approach across sites, avoids duplication of effort, and facilitates responses to requests for information from the regulators and the public. This paper provides background information on the regulatory requirements for data gathering and analysis for environmental restoration activities, and outlines the data and information management requirements for completing the pre-remediation phases of an environmental restoration project. Information management systems for integrating the regulatory and institutional requirements of the environmental restoration process with the technical data and analysis requirements are also described. 7 refs

Gas system Upgrade for the BaBar IFR Detector at SLAC

International Nuclear Information System (INIS)

Foulkes, S

2004-01-01

A new gas distribution and monitoring system was installed as part of an upgrade of the forward endcap muon detection system (IFR) of the BaBar detector at SLAC. Over 300 gas circuits are controlled and monitored. The return gas flow is monitored by digital bubblers which use photo-gate electronics to count the bubbling rate. The rates are monitored in real time and recorded in a history database allowing studies of flow rate versus chamber performance

SLAC/SPIRES Announces the Top-Cited Papers of 2000

International Nuclear Information System (INIS)

O'Connell, Heath B

2002-01-01

Physicists who search the literature on elementary particles know that the SLAC library's SPIRES-HEP database provides an essential tool. The database lists virtually every paper published or even preprinted in high energy physics over the past thirty years. The database connects preprint or eprint versions to articles published in journals or conference proceedings, providing access to all phases of the publication history. In addition, most papers have backward links to the papers they cite and forward links to the papers citing them. These citation linkages provide a very effective means of searching the literature on any topic of interest. In the past few years, SPIRES-HEP has been automatically harvesting reference citations from eprints, creating a web of links which indexes the literature in a quite thorough manner. As a byproduct of this citation linkage, SPIRES-HEP can easily search out the papers most highly cited by publications in high-energy physics. The list of papers with the most citations in a given year provides a snapshot of the hottest topics that have engaged the attention of theorists and experimenters. For the past several years, SPIRES-HEP has posted a scientific review of the year's top-cited papers. The whole collection of these reviews can be found on the Web at: http://www.slac.stanford.edu/library/topcites/. We have recently posted the topcite lists for the year 2000. These materials include a list of the papers with more than 100 citations in the past year, and a list of the paper with more than 1000 citations over the history of the SPIRES-HEP database

A study on the influence of the regulatory requirements of a nuclear facility during decommissioning activities

Energy Technology Data Exchange (ETDEWEB)

Park, Hee Seong; Park, Seung Kook; Park, Kook Nam; Hong, Yun Jeong; Park, Jang Jin; Choi, Jong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

The preliminary decommissioning plan should be written with various chapters such as a radiological characterization, a decommissioning strategy and methods, a design for decommissioning usability, a safety evaluation, decontamination and dismantling activities, radioactive waste management, an environmental effect evaluation, and fire protection. The process requirements of the decommissioning project and the technical requirements and technical criteria should comply with regulatory requirements when dismantling of a nuclear facility. The requirements related to safety in the dismantling of a nuclear facility refer to the IAEA safety serious. The present paper indicates that a decommissioning design and plan, dismantling activities, and a decommissioning project will be influenced by the decommissioning regulatory requirements when dismantling of a nuclear facility. We hereby paved the way to find the effect of the regulatory requirements on the decommissioning of a whole area from the decommissioning strategy to the radioactive waste treatment when dismantling a nuclear facility. The decommissioning requirements have a unique feature in terms of a horizontal relationship as well as a vertical relationship from the regulation requirements to the decommissioning technical requirements. The decommissioning requirements management will be conducted through research that can recognize a multiple relationship in the next stage.

Status of the SLAC/LBL/LLNL B-factory and the BABAR detector

International Nuclear Information System (INIS)

Oddone, P.

1994-10-01

After a brief introduction on the physics reach of the SLAC/LBL/LLNL Asymmetric B-Factory, the author describes the status of the accelerator and the detector as of the end of 1994. At this time, essentially all major decisions have been made, including the choice of particle identification for the detector. The author concludes this report with the description of the schedule for the construction of both accelerator and detector

The development of the Next Linear Collider at SLAC

International Nuclear Information System (INIS)

Ruth, R.D.

1992-02-01

At SLAC, we are pursuing the design of a Next Linear Collider (NLC) which would begin with a center-of-mass energy of 0.5 TeV and be upgradable to at least 1.0 TeV, and possibly 1.5 TeV. The luminosity is designed to be 10 33 cm -2 s -1 at the lower energy and 10 34 cm -2 s -1 at the top energy. In this paper, we discuss the accelerator physics issues which are important in our approach, and also the present state of the technology development. We also review the impact that the SLC has had in the evolution of our basic approach

Laser Safety for the Experimental Halls at SLAC_s Linac Coherent Light Source (LCLS)

Energy Technology Data Exchange (ETDEWEB)

Woods, Michael; Anthony, Perry; /SLAC; Barat, Ken; /LBL, Berkeley; Gilevich, Sasha; Hays, Greg; White, William E.; /SLAC

2009-01-15

The LCLS at the SLAC National Accelerator Laboratory will be the world's first source of an intense hard x-ray laser beam, generating x-rays with wavelengths of 1nm and pulse durations less than 100fs. The ultrafast x-ray pulses will be used in pump-probe experiments to take stop-motion pictures of atoms and molecules in motion, with pulses powerful enough to take diffraction images of single molecules, enabling scientists to elucidate fundamental processes of chemistry and biology. Ultrafast conventional lasers will be used as the pump. In 2009, LCLS will deliver beam to the Atomic Molecular and Optical (AMO) Experiment, located in one of 3 x-ray Hutches in the Near Experimental Hall (NEH). The NEH includes a centralized Laser Hall, containing up to three Class 4 laser systems, three x-ray Hutches for experiments and vacuum transport tubes for delivering laser beams to the Hutches. The main components of the NEH laser systems are a Ti:sapphire oscillator, a regen amplifier, green pump lasers for the oscillator and regen, a pulse compressor and a harmonics conversion unit. Laser safety considerations and controls for the ultrafast laser beams, multiple laser controlled areas, and user facility issues are discussed.

Methods for ensuring compliance with regulatory requirements: regulators and operators

International Nuclear Information System (INIS)

Fleischmann, A.W.

1989-01-01

Some of the methods of ensuring compliance with regulatory requirements contained in various radiation protection documents such as Regulations, ICRP Recommendations etc. are considered. These include radiation safety officers and radiation safety committees, personnel monitoring services, dissemination of information, inspection services and legislative power of enforcement. Difficulties in ensuring compliance include outmoded legislation, financial and personnel constraints

Regulatory Guide 1.79 safety injection recirculation test requirements, fact or fiction

International Nuclear Information System (INIS)

Roberts, J.K.

1976-01-01

The overwhelming concern of the general public in this day of state nuclear initiatives is the basic question, ''is nuclear power safe.'' Much of this concern has focused on the emergency core cooling systems. This public attention spotlights the testing organization's responsibility during startup of proving the operation and reliability of the emergency core cooling systems. The standard established by the Nuclear Regulatory Commission for testing emergency core cooling systems is Regulatory Guide 1.79 ''Preoperational Testing of Emergency Core Cooling Systems for Pressurized Water Reactors''. The nuclear industry must satisfy the testing requirements of Regulatory Guide 1.79 to meet their responsibility to the public; and to prevent future embarrassment when questioned on the adequacy of emergency core cooling systems

Use of probabilistic risk assessments to define areas of possible exemption from regulatory requirements

International Nuclear Information System (INIS)

Thompson, C.A.; Carlson, D.; Kolaczkowski, A.; LaChance, J.

1988-01-01

The Risk-Based Licensing Program (RBLP) was sponsored by the Department of Energy for the purpose of establishing and demonstrating an approach for identifying potential areas for exemption from current regulatory requirements in the licensing of nuclear power plants. Such an approach could assist in the improvement of the regulatory process for both current and future nuclear plant designs. Use of the methodology could result in streamlining the regulatory process by eliminating unnecessarily detailed reviews of portions of a plant design not important to risk. The RBLP methodology utilizes probabilistic risk assessments, (PRAs), which are required of all future applicants for nuclear power plant licenses. PRA results are used as a screening tool to determine the risk significance of various plant features which are correlated to the risk importance of regulations to identify potential areas for regulatory exemption. Additional consideration is then given to non-risk factors in the final determination of exemption candidates. The RBLP methodology was demonstrated using an existing PRA. The results of the demonstration are highlighted. 10 refs

Regulatory requirements for designing PET-CT facility in India

International Nuclear Information System (INIS)

Tandon, Pankaj

2010-01-01

In India, cyclotron-produced radionuclides are gaining importance in molecular imaging in Nuclear Medicine (NM) departments. The importance of this modality among others is due to the fact that it provides valuable clinical information, which was lacking in other available modalities. Presently, every well-established hospital would like to procure Medical Cyclotron or positron emission tomography-computed tomography (PET-CT) facility in their NM department. Because cyclotron-produced radionuclides have higher energy than the other routinely used radionuclides for diagnosis, it becomes essential for the user to know about the regulatory requirement and radiation safety precautions that one has to take for the installation of this new modality in their premises. The various stages of approval of PET-CT facility by the Atomic Energy Regulatory Board (AERB) and important steps that one has to know/follow before planning for this new facility are summarized

Data Quality Objectives for Regulatory Requirements for Hazardous and Radioactive Air Emissions Sampling and Analysis; FINAL

International Nuclear Information System (INIS)

MULKEY, C.H.

1999-01-01

This document describes the results of the data quality objective (DQO) process undertaken to define data needs for state and federal requirements associated with toxic, hazardous, and/or radiological air emissions under the jurisdiction of the River Protection Project (RPP). Hereafter, this document is referred to as the Air DQO. The primary drivers for characterization under this DQO are the regulatory requirements pursuant to Washington State regulations, that may require sampling and analysis. The federal regulations concerning air emissions are incorporated into the Washington State regulations. Data needs exist for nonradioactive and radioactive waste constituents and characteristics as identified through the DQO process described in this document. The purpose is to identify current data needs for complying with regulatory drivers for the measurement of air emissions from RPP facilities in support of air permitting. These drivers include best management practices; similar analyses may have more than one regulatory driver. This document should not be used for determining overall compliance with regulations because the regulations are in constant change, and this document may not reflect the latest regulatory requirements. Regulatory requirements are also expected to change as various permits are issued. Data needs require samples for both radionuclides and nonradionuclide analytes of air emissions from tanks and stored waste containers. The collection of data is to support environmental permitting and compliance, not for health and safety issues. This document does not address health or safety regulations or requirements (those of the Occupational Safety and Health Administration or the National Institute of Occupational Safety and Health) or continuous emission monitoring systems. This DQO is applicable to all equipment, facilities, and operations under the jurisdiction of RPP that emit or have the potential to emit regulated air pollutants

THE SLACS SURVEY. VIII. THE RELATION BETWEEN ENVIRONMENT AND INTERNAL STRUCTURE OF EARLY-TYPE GALAXIES

NARCIS (Netherlands)

Treu, Tommaso; Gavazzi, Raphael; Gorecki, Alexia; Marshall, Philip J.; Koopmans, Leon V. E.; Bolton, Adam S.; Moustakas, Leonidas A.; Burles, Scott

2009-01-01

We study the relation between the internal structure of early-type galaxies and their environment using 70 strong gravitational lenses from the SLACS Survey. The Sloan Digital Sky Survey (SDSS) database is used to determine two measures of overdensity of galaxies around each lens-the projected

Risk-informed assessment of regulatory and design requirements for future nuclear power plants. Annual report

International Nuclear Information System (INIS)

2000-01-01

OAK B188 Risk-informed assessment of regulatory and design requirements for future nuclear power plants. Annual report. The overall goal of this research project is to support innovation in new nuclear power plant designs. This project is examining the implications, for future reactors and future safety regulation, of utilizing a new risk-informed regulatory system as a replacement for the current system. This innovation will be made possible through development of a scientific, highly risk-formed approach for the design and regulation of nuclear power plants. This approach will include the development and/or confirmation of corresponding regulatory requirements and industry standards. The major impediment to long term competitiveness of new nuclear plants in the U.S. is the capital cost component--which may need to be reduced on the order of 35% to 40% for Advanced Light Water Reactors (ALWRS) such as System 80+ and Advanced Boiling Water Reactor (ABWR). The required cost reduction for an ALWR such as AP600 or AP1000 would be expected to be less. Such reductions in capital cost will require a fundamental reevaluation of the industry standards and regulatory bases under which nuclear plants are designed and licensed. Fortunately, there is now an increasing awareness that many of the existing regulatory requirements and industry standards are not significantly contributing to safety and reliability and, therefore, are unnecessarily adding to nuclear plant costs. Not only does this degrade the economic competitiveness of nuclear energy, it results in unnecessary costs to the American electricity consumer. While addressing these concerns, this research project will be coordinated with current efforts of industry and NRC to develop risk-informed, performance-based regulations that affect the operation of the existing nuclear plants; however, this project will go further by focusing on the design of new plants

Risk-informed assessment of regulatory and design requirements for future nuclear power plants. Annual report

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-08-01

OAK B188 Risk-informed assessment of regulatory and design requirements for future nuclear power plants. Annual report. The overall goal of this research project is to support innovation in new nuclear power plant designs. This project is examining the implications, for future reactors and future safety regulation, of utilizing a new risk-informed regulatory system as a replacement for the current system. This innovation will be made possible through development of a scientific, highly risk-formed approach for the design and regulation of nuclear power plants. This approach will include the development and/or confirmation of corresponding regulatory requirements and industry standards. The major impediment to long term competitiveness of new nuclear plants in the U.S. is the capital cost component--which may need to be reduced on the order of 35% to 40% for Advanced Light Water Reactors (ALWRS) such as System 80+ and Advanced Boiling Water Reactor (ABWR). The required cost reduction for an ALWR such as AP600 or AP1000 would be expected to be less. Such reductions in capital cost will require a fundamental reevaluation of the industry standards and regulatory bases under which nuclear plants are designed and licensed. Fortunately, there is now an increasing awareness that many of the existing regulatory requirements and industry standards are not significantly contributing to safety and reliability and, therefore, are unnecessarily adding to nuclear plant costs. Not only does this degrade the economic competitiveness of nuclear energy, it results in unnecessary costs to the American electricity consumer. While addressing these concerns, this research project will be coordinated with current efforts of industry and NRC to develop risk-informed, performance-based regulations that affect the operation of the existing nuclear plants; however, this project will go further by focusing on the design of new plants.

Governmental, Legal and Regulatory Framework for Safety. General Safety Requirements. Part 1 (Spanish Edition)

International Nuclear Information System (INIS)

2010-01-01

The objective of this publication is to establish requirements in respect of the governmental, legal and regulatory framework for safety. It covers the essential aspects of the framework for establishing a regulatory body and taking other actions necessary to ensure the effective regulatory control of facilities and activities utilized for peaceful purposes. Other responsibilities and functions, such as liaison within the global safety regime and on support services for safety (including radiation protection), emergency preparedness and response, nuclear security, and the State system of accounting for and control of nuclear material, are also covered

Governmental, Legal and Regulatory Framework for Safety. General Safety Requirements. Part 1 (French Edition)

International Nuclear Information System (INIS)

2010-01-01

The objective of this publication is to establish requirements in respect of the governmental, legal and regulatory framework for safety. It covers the essential aspects of the framework for establishing a regulatory body and taking other actions necessary to ensure the effective regulatory control of facilities and activities utilized for peaceful purposes. Other responsibilities and functions, such as liaison within the global safety regime and on support services for safety (including radiation protection), emergency preparedness and response, nuclear security, and the State system of accounting for and control of nuclear material, are also covered

Governmental, Legal and Regulatory Framework for Safety. General Safety Requirements. Part 1 (Chinese Edition)

International Nuclear Information System (INIS)

2010-01-01

The objective of this publication is to establish requirements in respect of the governmental, legal and regulatory framework for safety. It covers the essential aspects of the framework for establishing a regulatory body and taking other actions necessary to ensure the effective regulatory control of facilities and activities utilized for peaceful purposes. Other responsibilities and functions, such as liaison within the global safety regime and on support services for safety (including radiation protection), emergency preparedness and response, nuclear security, and the State system of accounting for and control of nuclear material, are also covered

Governmental, Legal and Regulatory Framework for Safety. General Safety Requirements. Part 1 (Arabic Edition)

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-09-15

The objective of this publication is to establish requirements in respect of the governmental, legal and regulatory framework for safety. It covers the essential aspects of the framework for establishing a regulatory body and taking other actions necessary to ensure the effective regulatory control of facilities and activities utilized for peaceful purposes. Other responsibilities and functions, such as liaison within the global safety regime and on support services for safety (including radiation protection), emergency preparedness and response, nuclear security, and the State system of accounting for and control of nuclear material, are also covered.

Regulatory philosophy and requirements for radiation control in Canadian uranium mine-mill facilities

International Nuclear Information System (INIS)

Dory, A.B.

1981-10-01

The approach the Canadian Atomic Energy Control Board takes in licensing uranium mine/mill facilities is based on a minimum of rigidly set regulatory requirements. The regulations state only the basic objectives: the obligation to acquire a licence, some administrative and reporting requirements, and exposure limits. The regulations are supported by a set of regulatory guides. The operator always has the option of following different procedures if he can demonstrate that they will produce the same or better results. Good relationships exist between the AECB and mine management as well as trade unions. Under this approach, however, it is difficult to take action against uncooperative parties. The Board has decided that a somewhat more formalized system is necessary. New regulations are being drafted, giving more detailed licensing and administrative requirements and covering the areas of ventilation and worker and supervisor education more thoroughly

Review of regulatory requirements relevant to calibration of monitoring instruments in research reactors

Energy Technology Data Exchange (ETDEWEB)

Gomaa, Hassan; Khedr, Ahmed; El-Din Talha, Kamal [Egyptian Nuclear and Radiological Regulatory Authority, Cairo (Egypt). Nuclear Safety Engineering Dept.

2015-05-15

The objective of this work is to demonstrate the regulatory requirements pertaining to calibration of monitoring instruments in research reactors. The regulatory statements concerning this subject in IAEA safety standards and the implementation of such regulations in twelve countries with different levels of nuclear programs are surveyed: Australia, Bulgaria, Canada, Egypt, Finland, Germany, Hungary, Slovenia, South Korea, Spain, United Kingdom of England and United States of America. In addition, the requirements of ISO/IEC17025 and NUPIC (Nuclear Utilities Procurement Issues Committee) are compared. Seven technical and administrate aspects are suggested as the comparison criteria and the explicit expression of the statements, the level of document (i.e.: act, requirement or guide) are the considered resources. The main differences and similarities between the different approaches are identified in order to provide an input for future development of the national regulations.

Search milli-charged particles at SLAC

Energy Technology Data Exchange (ETDEWEB)

Langeveld, W.G.J. [Stanford Univ., CA (United States)

1997-01-01

Particles with electric charge q {triple_bond} Qe {le} 10{sup -3} e and masses in the range 1-1000 MeV/c{sup 2} are not excluded by present experiments or by astrophysical or cosmological arguments. A beam dump experiment uniquely suited to the detection of such {open_quotes}milli-charged{close_quotes} particles has been carried out at SLAC, utilizing the short-duration pulses of the SLC electron beam to establish a tight coincidence window for the signal. The detector, a large scintillation counter sensitive to very small energy depositions, provided much greater sensitivity than previous searches. Analysis of the data leads to the exclusion of a substantial portion of the charge-mass plane. In this report, a preliminary mass-dependent upper limit is presented for the charge of milli-charged particles, ranging from Q = 1.7 x 10{sup -5} at milli-charged particle mass 0.1 MeV/c{sup 2} to Q = 9.5 x 10{sup -4} at 100 MeV/c{sup 2}.

Romanian regulatory requirements on nuclear field specific education needs

International Nuclear Information System (INIS)

Biro, L.; Velicu, O.

2004-01-01

This work is intended as a general presentation of the educational system and research field, with reference to nuclear sciences, and the legal system, with reference to requirements established by the regulatory body for the professional qualification and periodic training of personnel involved in different activities in the nuclear field. Thus, part 2 and 3 of the work present only public information regarding the education in nuclear sciences and nuclear research in Romania; in part 4 the CNCAN requirements for the personnel training, specific to nuclear activities are slightly detailed; part 5 consists of few words about the public information activities in Romania; and part 6 tries to draw a conclusion. (authors)

Regulatory requirements to the thermal-hydraulic and thermal-mechanical computer codes

International Nuclear Information System (INIS)

Vitkova, M.; Kalchev, B.; Stefanova, S.

2006-01-01

The paper presents an overview of the regulatory requirements to the thermal-hydraulic and thermal-mechanical computer codes, which are used for safety assessment of the fuel design and the fuel utilization. Some requirements to the model development, verification and validation of the codes and analysis of code uncertainties are also define. Questions concerning Quality Assurance during development and implementation of the codes as well as preparation of a detailed verification and validation plan are briefly discussed

High gradient tests of SLAC Linear Collider Accelerator Structures

International Nuclear Information System (INIS)

Wang, J.W.; Deruyter, H.; Eichner, J.; Fant, K.H.; Hoag, H.A.; Koontz, R.F.; Lavine, T.; Loew, G.A.; Loewen, R.; Menegat, L.

1994-08-01

This paper describes the current SLAC R ampersand D program to develop room temperature accelerator structures for the Next Linear Collider (NLC). The structures are designed to operate at 11.4 GHz at an accelerating gradient in the range of 50 to 100 MV/m. In the past year a 26 cm constant-impedance traveling-wave section, a 75 cm constant-impedance traveling-wave section, and a 1.8 m traveling-wave section with detuned deflecting modes have been high-power tested. The paper presents a brief description of the RF test setup, the design and manufacturing details of the structures, and a discussion of test results including field emission, RF processing, dark current spectrum and RF breakdown

Method for developing cost estimates for generic regulatory requirements

International Nuclear Information System (INIS)

1985-01-01

The NRC has established a practice of performing regulatory analyses, reflecting costs as well as benefits, of proposed new or revised generic requirements. A method had been developed to assist the NRC in preparing the types of cost estimates required for this purpose and for assigning priorities in the resolution of generic safety issues. The cost of a generic requirement is defined as the net present value of total lifetime cost incurred by the public, industry, and government in implementing the requirement for all affected plants. The method described here is for commercial light-water-reactor power plants. Estimating the cost for a generic requirement involves several steps: (1) identifying the activities that must be carried out to fully implement the requirement, (2) defining the work packages associated with the major activities, (3) identifying the individual elements of cost for each work package, (4) estimating the magnitude of each cost element, (5) aggregating individual plant costs over the plant lifetime, and (6) aggregating all plant costs and generic costs to produce a total, national, present value of lifetime cost for the requirement. The method developed addresses all six steps. In this paper, we discuss on the first three

Federal and state regulatory requirements for decontamination and decommissioning at US Department of Energy Oak Ridge Operations Facilities

International Nuclear Information System (INIS)

Etnier, E.L.; Houlberg, L.M.; Bock, R.E.

1994-06-01

The purpose of this report is to address regulatory requirements for decontamination and decommissioning (D and D) activities at the Oak Ridge Reservation and Paducah Gaseous Diffusion Plant. This report is a summary of potential federal and state regulatory requirements applicable to general D and D activities. Excerpts are presented in the text and tables from the complete set of regulatory requirements. This report should be used as a guide to the major regulatory issues related to D and D. Compliance with other federal, state, and local regulations not addressed here may be required and should be addressed carefully by project management on a site-specific basis. The report summarizes the major acts and implementing regulations (e.g., Resource and Conservation Recovery Act, Clean Air Act, and Toxic Substances Control Act) only with regard to D and D activities. Additional regulatory drivers for D and D activities may be established through negotiated agreements, such as the Federal Facility Agreement and the US Environmental Protection Agency Mixed Waste Federal Facility Compliance Agreement; these are discussed in this report. The DOE orders and Energy Systems procedures also are summarized briefly in instances where they directly apply to D and D

Governmental, Legal and Regulatory Framework for Safety. General Safety Requirements. Part 1, Revision 1 (Chinese Edition)

International Nuclear Information System (INIS)

2016-01-01

This publication establishes requirements in respect of the governmental, legal and regulatory framework for safety. It covers the essential aspects of the framework for establishing a regulatory body and taking other actions necessary to ensure the effective regulatory control of facilities and activities utilized for peaceful purposes. Other responsibilities and functions, such as liaison within the global safety regime and on support services for safety (including radiation protection), emergency preparedness and response, nuclear security, and the State system of accounting for and control of nuclear material, are also covered. A review of Safety Requirements publications was commenced in 2011 following the accident in the Fukushima Daiichi nuclear power plant in Japan. The review revealed no significant areas of weakness and resulted in just a small set of amendments to strengthen the requirements and facilitate their implementation, which are contained in the present publication.

Parton distributions from SMC and SLAC data

International Nuclear Information System (INIS)

Ramsey, G.P.

1996-01-01

We have extracted spin-weighted parton distributions in a proton from recent data at CERN and SLAC. The valence, sea quark and Antiquark spin-weighted distributions are determined separately. The data are all consistent with a small to moderate polarized gluon distribution, so that the anomaly term is not significant in the determination of the constituent contributions to the spin of the proton. We have analyzed the consistency of the results obtained from various sets of data and the Biorken sum rule. Although all data are consistent with the sum rule, the polarized distributions from different experiments vary, even with higher order QCD corrections taken into account. Results split into two models, one set implying a large polarized strange sea which violates the positivity bound, and the other set yielding a smaller polarized strange sea. Only further experiments which extract information about the polarized sea will reconcile these differences. We suggest specific experiments which can be performed to determine the size of the polarized sea and gluons

Personnel dose equivalent monitoring at SLAC using lithium-fluoride TLD's [thermoluminescent dosimeters

International Nuclear Information System (INIS)

Jenkins, T.M.; Busick, D.D.

1987-03-01

TLD's replaced film badges in the early 1970's for all dose equivalent monitoring, both neutron and photon, and for all locations at SLAC. The photon TLD's, composed of Li-7 loaded teflon discs, are calibrated using conventional gamma-ray sources; i.e., Co-60, Cs-137, etc. For these TLD's a nominal value of 1 nC/mrem is used, and is independent of source energy for 100 keV to 3 MeV. Since measured dose equivalents at SLAC are only a small fraction of the allowable levels, it was not deemed necessary to develop neutron dosimeters which would measure dose equivalent accurately for all possible neutron spectra. Today, wallet TLD's, composed of pairs of Li-7 and Li-6 discs, are used, with the Li-6 measuring only thermal neutrons; i.e., they aren't moderated in any way to make them sensitive to neutrons with energies greater than thermal. The assumption is made that there is a correlation between thermal neutron fluences and fast neutron fluences around the research area where almost all neutron doses (exclusive of sealed sources) are received. The calibration factor for these Li-6 TLD's is 1 nC/mrem of fast neutrons. The method of determining the validity of this calibration is the subject of this note. 4 refs., 9 figs., 1 tab

FEL research and development at the SLAC sub-picosecond photon source, SPPS

International Nuclear Information System (INIS)

Bentson, L.; Bolton, P.; Bong, E.; Emma, P.; Galayda, J.; Hastings, J.; Krejcik, P.; Rago, C.; Rifkin, J.; Spencer, C.M.

2003-01-01

An upgrade project to the SLAC linac allows ultra-short electron bunches to be interleaved with the routine high-energy physics program operation, for use with an undulator to produce short-pulse, high-brightness X-rays. The linac upgrade comprises of the installation in the summer of 2002 of a bunch compressor chicane of similar design to the Linac Coherent Light Source (LCLS) project. A final compression stage in the high-energy Final Focus Test Beam (FFTB) line compresses the 28 GeV, 3.4 nC electron bunch to 80 fs FWHM, where a 5 m section of undulator (K=4.45) will produce 1.5 A X-rays with 3x10 7 photons per pulse and a peak brightness of 4x10 24 photons mm -2 mrad -2 s -1 (0.1% BW). The facility will allow us to test the dynamics and associated technology of bunch compression and gain valuable experience for the LCLS using the SLAC linac. New ultra-short electron bunch diagnostic techniques will be developed hand in hand with the same ultra-fast laser technology to be used for LCLS. Issues of high peak power (27 GW) X-ray transport and optics can be addressed at this facility as well as pump-probe and ultra-fast laser timing and stability issues

Regulatory requirements important to Hanford single-shell tank waste management decisions

International Nuclear Information System (INIS)

Keller, J.F.; Woodruff, M.G.

1989-06-01

This report provides an initial analysis of the regulations that may be pertinent to SST management activities (e.g., characterization, disposal, retrieval, processing, etc.) and the interrelationships among those regulations. Waste disposal decisions regarding SST waste must consider the regulatory requirements against which technical solutions will be evaluated. Regulatory requirements can also be used as guidelines for management and disposal of waste in a manner that protects human health and safety and the environment. Also, in cases where waste management regulations do not specifically address a waste form, such as radioactive mixed waste, the SST waste may come under the purview of a number of regulations related to radioactive waste management, hazardous waste management, and water and air quality protection. This report provides a comprehensive review of the environmental pollution control and radioactive waste management statutes and regulations that are relevant to SST waste characterization and management. Also, other statutes and regulations that contain technical standards that may be used in the absence of directly applicable regulations are analyzed. 8 refs., 4 figs

Fast track-finding trigger processor for the SLAC/LBL Mark II Detector

International Nuclear Information System (INIS)

Brafman, H.; Breidenbach, M.; Hettel, R.; Himel, T.; Horelick, D.

1977-10-01

The SLAC/LBL Mark II Magnetic Detector consists of various particle detectors arranged in cylindrical symmetry located in and around an axial magnetic field. A versatile, programmable secondary trigger processor was designed and built to find curved tracks in the detector. The system operates at a 10 MHz clock rate with a total processing time of 34 μsec and is used to ''trigger'' the data processing computer, thereby rejecting background and greatly improving the data acquisition aspects of the detector-computer combination

Technical Design Report for the FACET-II Project at SLAC National Accelerator Laboratory

Energy Technology Data Exchange (ETDEWEB)

None, None

2016-08-26

Electrons can “surf” on waves of plasma – a hot gas of charged particles – gaining very high energies in very short distances. This approach, called plasma wakefield acceleration, has the potential to dramatically shrink the size and cost of particle accelerators. Research at the SLAC National Accelerator Laboratory has demonstrated that plasmas can provide 1,000 times the acceleration in a given distance compared with current technologies. Developing revolutionary and more efficient acceleration techniques that allow for an affordable high-energy collider has been the focus of FACET, a National User Facility at SLAC. FACET used part of SLAC’s two-mile-long linear accelerator to generate high-density beams of electrons and their antimatter counterparts, positrons. Research into plasma wakefield acceleration was the primary motivation for constructing FACET. In April 2016, FACET operations came to an end to make way for the second phase of SLAC’s x-ray laser, the LCLS-II, which will use part of the tunnel occupied by FACET. FACET-II is a new test facility to provide the unique capability to develop advanced acceleration and coherent radiation techniques with high-energy electron and positron beams. FACET-II represents a major upgrade over current FACET capabilities and the breadth of the potential research program makes it truly unique.

Preparation of safety regulatory requirements for new technology like digital system

International Nuclear Information System (INIS)

2012-01-01

The current regulatory requirements on digital instrumentation and control system have been reviewed by JNES, considering international trend discussed in DICWG of MDEP. MDEP DICWG held in OECD/NEA gives the opportunity to identify the convergence of applicable standards. The working group's activities include: identifying and prioritising the member countries' challenges, practices, and needs regarding standards and regulatory guidance on digital instrumentation and control; identifying areas of importance and needs for convergence of existing standards and guidance or development of new standards; sharing of information; and identifying common positions among the member countries for areas of particular importance and need. The DICWG drafted common positions on specific issues which are based on the existing standards, national regulatory guidance, best practices, and group inputs using an agreed process and framework. The following two general common positions are discussed and to be issued in this fiscal year. Verification and Validation throughout the life cycle of safety systems using digital computers. The Impact of Cyber Security Features on Digital I and C Safety Systems. (author)

A 100 GeV SLAC Linac

International Nuclear Information System (INIS)

Farkas, Zoltan D

2002-01-01

The SLAC beam energy can be increased from the current 50 GeV to 100 GeV, if we change the operating frequency from the present 2856 MHz to 11424 MHz, using technology developed for the NLC. We replace the power distribution system with a proposed NLC distribution system as shown in Fig. 1. The four 3 meter s-band 820 nS fill time accelerator sections are replaced by six 2 meter x-band 120 nS fill time sections. Thus the accelerator length per klystron retains the same length, 12 meters. The 4050 65MW-3.5(micro)S klystrons are replaced by 75MW-1.5(micro)S permanent magnet klystrons developed here and in Japan. The present input to the klystrons would be multiplied by a factor of 4 and possibly amplified. The SLED [1] cavities have to be replaced. The increase in beam voltage is due to the higher elastance to group velocity ratio, higher compression ratio and higher unloaded to external Q ratio of the new SLED cavities. The average power input is reduced because of the narrower klystron pulse width and because the klystron electro-magnets are replaced by permanent magnets

Dipole magnets for the SLAC 50 GeV A-Line upgrade

International Nuclear Information System (INIS)

Erickson, R.; DeBarger, S.; Spencer, C.M.; Wolf, Z.

1995-05-01

The SLAC A-Line is a transport system originally designed to deliver electron beams of up to 25 GeV to fixed target experiments in End Station A. To raise the beam energy capability of the A-Line to 52 GeV, the eight original bending magnets, plus four more of the same type, have been modified by reducing their gaps and adding trim windings to compensate for energy loss due to synchrotron radiation. In this paper the authors describe the modifications that have been completed, and they compare test and measurement results with predicted performance

Regulatory quality assurance requirements for the operation of nuclear R and D facilities in Korea

International Nuclear Information System (INIS)

Kwon, H.I.; Lim, N.J.

2006-01-01

Full text: Korea Atomic Energy Research Institute (KAERI) has many R and D facilities in operation. including HANARO research reactor, radioactive waste treatment facility (RWTF), post-irradiation examination facility (PIEF) and irradiated material test facility (IMEF). Recently. nation-wide interest is focused on the safety and security of major industrial facilities. Safe operation of nuclear facilities is imperative because of the consequence of public disaster by radiological release/contamination, in case of an accident. Recently, Ministry of Science and Technology (MOST) of the Korean government announced amendments of Atomic Energy laws to enforce requirements of the physical protection and radiological emergency. All provisions on nuclear safety regulation and radiation protection are entrusted to the Atomic Energy Act(AEA). The Act is enacted as the main law concerning the safety regulation of nuclear installations, and is supplemented by the Enforcement Decree and Enforcement Regulation of the Act. These Atomic Energy laws include provisions on the construction permission and the operation license of nuclear installations, such as nuclear power reactors, research reactors, nuclear ships, nuclear fuel fabrication facilities, spent fuel treatment facilities, etc. Regulatory requirements for the regulatory inspection and the safety measures for operation are also defined in the laws. The Notice of the MOST prescribes specific issues including regulatory requirements and technical standards, as entrusted by the AEA, the Decree and the Regulation. Detailed QA requirements for nuclear installations are specified differently, depending upon the type of facility. The guidelines for safety reviews and regulatory inspections are developed by the Korea Institute of Nuclear Safety (KINS), which is an exclusive organization for safety regulation of nuclear installations in Korea. In this paper, the context of the Atomic Energy laws were reviewed to confirm the

WIPP Waste Characterization: Implementing Regulatory Requirements in the Real World

International Nuclear Information System (INIS)

Cooper Wayman, J.D.; Goldstein, J.D.

1999-01-01

It is imperative to ensure compliance of the Waste Isolation Pilot Project (WIPP) with applicable statutory and regulatory requirements. In particular, compliance with the waste characterization requirements of the Resource Conservation and Recovery Act (RCRA) and its implementing regulation found at 40 CFR Parts 262,264 and 265 for hazardous and mixed wastes, as well as those of the Atomic Energy Act of 1954, as amended, the Reorganization Plan No. 3 of 1970, the Nuclear Waste Policy Act of 1982, as amended, and the WIPP Land Withdrawal Act, as amended, and their implementing regulations found at 40 CFR Parts 191 and 194 for non-mixed radioactive wastes, are often difficult to ensure at the operational level. For example, where a regulation may limit a waste to a certain concentration, this concentration may be difficult to measure. For example, does the definition of transuranic waste (TRU) as 100 nCi/grain of alpha-emitting transuranic isotopes per gram of waste mean that the radioassay of a waste must show a reading of 100 plus the sampling and measurement error for the waste to be a TRU waste? Although the use of acceptable knowledge to characterize waste is authorized by statute, regulation and DOE Orders, its implementation is similarly beset with difficulty. When is a document or documents sufficient to constitute acceptable knowledge? What standard can be used to determine if knowledge is acceptable for waste characterization purposes? The inherent conflict between waste characterization regulatory requirements and their implementation in the real world, and the resolution of this conflict, will be discussed

The analog processing system for the Liquid Argon Calorimeter for SLD at SLAC

International Nuclear Information System (INIS)

Haller, G.M.; Nelson, D.; Freytag, D.R.

1986-09-01

The analog processing system for the Liquid Argon Calorimeter for the SLD project at SLAC is described. Amplification, storage of the analog information, and multiplexing is realized on specially developed hybrids, which will be mounted directly on the detector. This leads to a substantial reduction of the cable plant. Test results for the amplifier and for the sampling and multiplexing hybrid (CDU hybrid) are presented. The latter hybird contains a custom monolithic device, the Calorimeter Data Unit

Thermal stress analysis of the SLAC moveable mask. Addendum 2

International Nuclear Information System (INIS)

Johnson, G.L.

1985-01-01

X-ray beams emerging from the new SLAC electron-positron storage ring (PEP) can impinge on the walls of tangential divertor channels. A moveable mask made of 6061-T6 aluminum is installed in the channel to limit wall heating. The mask is cooled with water flowing axially at 30 0 C. Beam strikes on the mask cause highly localized heating in the channel structure. Analyses were completed to determine the temperatures and thermally-induced stresses due to this heating. The current design and operating conditions should result in the entrance to the moveable mask operating at a peak temperature of 88 0 C with a peak thermal stress at 19% of the yield of 6061-T6 aluminum

SLAC collider injector, RF-drive synchronization and trigger electronics, and 15-AMP thermionic-gun development

International Nuclear Information System (INIS)

Koontz, R.; Miller, R.; McKinney, T.; Wilmunder, A.

1981-02-01

The rf drive system for the Collider Injector Development (EL CID) including laser timing, subharmonic buncher drive and phasing, and accelerator rf drive is described. The rf synchronized master trigger generation scheme for the collider is outlined. Also, a 15 amp peak, 200 kV short pulse gun being developed at SLAC as a backup to the Sinclair laser gun is described

Preparation of safety regulatory requirements for new technology like digital system

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

The current regulatory requirements on digital instrumentation and control system have been reviewed by JNES, considering international trend discussed in DICWG of MDEP. MDEP DICWG held in OECD/NEA gives the opportunity to identify the convergence of applicable standards. The working group's activities include: identifying and prioritising the member countries' challenges, practices, and needs regarding standards and regulatory guidance on digital instrumentation and control; identifying areas of importance and needs for convergence of existing standards and guidance or development of new standards; sharing of information; and identifying common positions among the member countries for areas of particular importance and need. The DICWG drafted common positions on specific issues which are based on the existing standards, national regulatory guidance, best practices, and group inputs using an agreed process and framework. The following four general common positions have been discussed in this fiscal year. The Treatment of Common Cause Failure Resulting from Software within Digital Safety Systems, The Treatment of Hardware Description Language(HDL) Programmed Devices for Use in Nuclear Safety System, Factory Acceptance Test and Site Acceptance Test, The Use of Automatic Tests to Perform Surveilance for Digital Systems. (author)

Introduction to high-energy physics and the Stanford Linear Accelerator Center (SLAC)

International Nuclear Information System (INIS)

Clearwater, S.

1983-03-01

The type of research done at SLAC is called High Energy Physics, or Particle Physics. This is basic research in the study of fundamental particles and their interactions. Basic research is research for the sake of learning something. Any practical application cannot be predicted, the understanding is the end in itself. Interactions are how particles behave toward one another, for example some particles attract one another while others repel and still others ignore each other. Interactions of elementary particles are studied to reveal the underlying structure of the universe

Introduction to high-energy physics and the Stanford Linear Accelerator Center (SLAC)

Energy Technology Data Exchange (ETDEWEB)

Clearwater, S.

1983-03-01

The type of research done at SLAC is called High Energy Physics, or Particle Physics. This is basic research in the study of fundamental particles and their interactions. Basic research is research for the sake of learning something. Any practical application cannot be predicted, the understanding is the end in itself. Interactions are how particles behave toward one another, for example some particles attract one another while others repel and still others ignore each other. Interactions of elementary particles are studied to reveal the underlying structure of the universe.

The 50 GeV program at SLAC

International Nuclear Information System (INIS)

Prescott, C.Y.

1994-03-01

SLAC has undertaken a modes programs to upgrade the beam energy for fixed target experiments to 50 GeV. This upgrade is possible due to the previous extensive development work on the linac accelerating gradient for the SLC, which has been operational for over five years. The SLC can deliver a beam of energy up to 60 GeV using a pulse compression technique in the rf system which trades pulse length for a higher pulse amplitude. This mode of operation has been reliable and routine for the SLC. However the beam line transport which takes electrons or positrons from the end of the linac to the target in End Station A has not been upgraded from the original design energy of 25 GeV. The 50 GeV upgrade for the fixed target experiments consists in modifying and increasing the number of beam line dipole magnets to reach 50 GeV, plus modernization of the beam line instrumentation and controls. The plans for spin structure experiments using electron beams at energies up to 50 GeV are described

Regulatory requirements for demonstration of the achieved safety level at the Mochovce NPP before commissioning

International Nuclear Information System (INIS)

Lipar, M.

1997-01-01

A review of regulatory requirements for demonstration of the achieved safety level at the Mochovce NPP before commissioning is given. It contains licensing steps in Slovakia during commissioning; Status and methodology of Mochovce safety analysis report; Mochovce NPP safety enhancement program; Regulatory body policy towards Mochovce NPP safety enhancement; Recent development in Mochovce pre-operational safety enhancement program review and assessment process; Licensing steps in Slovakia during commissioning

Regulatory requirements on the calibration and use of survey instruments

International Nuclear Information System (INIS)

Domondon, D.B.

1989-01-01

Regulatory requirements on the provision, calibration and occasions of use of survey instruments are enumerated for a number of licensed activities. Two methods of calibrating survey instruments are described. Factors that must be taken into consideration in conducting calibrations, contents of calibration reports and of the sticker attached to the instrument which are needed for the correct use of the instrument are discussed. The precautions to be observed in order to insure correct use of survey instruments are described. (Auth.)

A study for the establishment of regulatory requirement and evaluation guide for station blackout in nuclear power plants

International Nuclear Information System (INIS)

Lim, J. H.; Koo, C. S.; Joo, W. P.; Oh, S. H.; Shin, W. K.

1999-01-01

The consequence of SBO event could be a severe accident unless AC power was restored within a proper time, because many safety systems depend upon AC power. Based on the severity, the SBO has been extensively studied since it was identified as Unresolved Safety Issue at USNRC. The resolution of those studies is a rule-making such as 10 CFR 50.63 and Regulatory Guide 1.155. But there is no regulatory requirements of SBO for an operating domestic nuclear power plant up to the present time. This tudy has established SBO rule(regulatory requirements and evaluation guides) for an operating PWR type of the operating nuclear power plants in Korea

Evolution of New cis-Regulatory Motifs Required for Cell-Specific Gene Expression in Caenorhabditis.

Directory of Open Access Journals (Sweden)

Michalis Barkoulas

2016-09-01

Full Text Available Patterning of C. elegans vulval cell fates relies on inductive signaling. In this induction event, a single cell, the gonadal anchor cell, secretes LIN-3/EGF and induces three out of six competent precursor cells to acquire a vulval fate. We previously showed that this developmental system is robust to a four-fold variation in lin-3/EGF genetic dose. Here using single-molecule FISH, we find that the mean level of expression of lin-3 in the anchor cell is remarkably conserved. No change in lin-3 expression level could be detected among C. elegans wild isolates and only a low level of change-less than 30%-in the Caenorhabditis genus and in Oscheius tipulae. In C. elegans, lin-3 expression in the anchor cell is known to require three transcription factor binding sites, specifically two E-boxes and a nuclear-hormone-receptor (NHR binding site. Mutation of any of these three elements in C. elegans results in a dramatic decrease in lin-3 expression. Yet only a single E-box is found in the Drosophilae supergroup of Caenorhabditis species, including C. angaria, while the NHR-binding site likely only evolved at the base of the Elegans group. We find that a transgene from C. angaria bearing a single E-box is sufficient for normal expression in C. elegans. Even a short 58 bp cis-regulatory fragment from C. angaria with this single E-box is able to replace the three transcription factor binding sites at the endogenous C. elegans lin-3 locus, resulting in the wild-type expression level. Thus, regulatory evolution occurring in cis within a 58 bp lin-3 fragment, results in a strict requirement for the NHR binding site and a second E-box in C. elegans. This single-cell, single-molecule, quantitative and functional evo-devo study demonstrates that conserved expression levels can hide extensive change in cis-regulatory site requirements and highlights the evolution of new cis-regulatory elements required for cell-specific gene expression.

Public consultation: regulatory requirement or business principle?

International Nuclear Information System (INIS)

Seeley, R.

1999-01-01

A summary is included of knowledge and experiences related to planning and implementing a public consultation program over a number of years in Shell Canada's Athabasca Oil Sands development. This project consists of three major sub- projects with a total estimated capital investment of $4 billion. The three sub- projects are: the Muskeg River Mine, the Scotford Upgrader, and the Corridor Pipeline. The facilities will produce 150,000 bbl/day of synthetic crude for over 25 years and are targeted to begin production in late 2002. From the title of the paper, although public consultation is required under environmental legislation, many companies are adopting a more pro-active approach to public consultation and participation as a business principle. This commitment to engage in and dialogue with stakeholders must be open, transparent and long term, not just during the regulatory process. Successful consultation begins with the prerequisites: senior management commitment, buy-in from the project or operating team that the process adds value, and the ability to listen and make changes. A consultation program is not a short term activity, but is rather an ongoing process linked to a business or operating principle. It requires long term resources and follow through on agreements and commitments made to stakeholders and communities

Public consultation: regulatory requirement or business principle?

Energy Technology Data Exchange (ETDEWEB)

Seeley, R. [Shell Canada Oil Sands, Calgary, AB (Canada)

1999-07-01

A summary is included of knowledge and experiences related to planning and implementing a public consultation program over a number of years in Shell Canada's Athabasca Oil Sands development. This project consists of three major sub- projects with a total estimated capital investment of $4 billion. The three sub- projects are: the Muskeg River Mine, the Scotford Upgrader, and the Corridor Pipeline. The facilities will produce 150,000 bbl/day of synthetic crude for over 25 years and are targeted to begin production in late 2002. From the title of the paper, although public consultation is required under environmental legislation, many companies are adopting a more pro-active approach to public consultation and participation as a business principle. This commitment to engage in and dialogue with stakeholders must be open, transparent and long term, not just during the regulatory process. Successful consultation begins with the prerequisites: senior management commitment, buy-in from the project or operating team that the process adds value, and the ability to listen and make changes. A consultation program is not a short term activity, but is rather an ongoing process linked to a business or operating principle. It requires long term resources and follow through on agreements and commitments made to stakeholders and communities.

Present and future colliding beam facilities at SLAC

International Nuclear Information System (INIS)

Wiedemann, H.

1977-07-01

In April 1972, the 3-GeV electron positron storage ring, SPEAR, was put into operation at the end of the linear accelerator at Stanford. By the recent discoveries in high energy physics the value of electron-positron storage rings for high energy physics has been clearly demonstrated. This development certainly encouraged the relatively early funding of the new electron-positron storage ring, PEP, at SLAC. In addition to its role as a particle physics research tool, SPEAR has been and remains a priceless model or prototype for larger storage rings like PEP. A few of the recent observations in SPEAR which have important implications to the design of PEP are described. Although the PEP design follows closely the SPEAR concept in many respects, it has its own distinctive and important features which are discussed in detail. Topics discussed include synchrotron-betatron resonances, beam losses, beam bunching, PEP design luminosity and energy, chromaticity correction in PEP, and the high energy cabability of PEP

Z0 physics from the Mark II at the SLC [SLAC Linear Collider

International Nuclear Information System (INIS)

Abrams, G.S.

1989-06-01

The MARK II detector has started to take data at the new SLAC Linear Collider. The novel aspects of the accelerator and of the MARK II are briefly described. Displays of event pictures from some of the early-on data are presented to illustrate the quality of the data. A first presentation of the results of an energy scan near the Z 0 mass that is currently in progress shows the expected resonant enhancement near 91 GeV. 2 refs., 23 figs., 1 tab

TOSCA calculations and measurements for the SLAC SLC damping ring dipole magnet

International Nuclear Information System (INIS)

Early, R.A.; Cobb, J.K.

1985-01-01

The SLAC damping ring dipole magnet was originally designed with removable nose pieces at the ends. Recently, a set of magnetic measurements was taken of the vertical component of induction along the center of the magnet for four different pole-end configurations and several current settings. The three dimensional computer code TOSCA, which is currently installed on the National Magnetic Fusion Energy Computer Center's Cray X-MP, was used to computer field values for the four configurations at current settings near saturation. Comparisons were made for magnetic induction as well as effective magnetic lengths for the different configurations

Nucleon resonance electroproduction at high momentum transers: Results from SLAC and suggestions for CEBAF

Energy Technology Data Exchange (ETDEWEB)

Keppel, C. [Virginia Union Univ., Richmond, VA (United States)

1994-04-01

Nucleon resonance electroproduction results from SLAC Experiment E14OX are presented. A CEBAF facility with doubled energy would enable similar high momentum transfer measurements to be made with greater accuracy. Of particular interest are the Delta P{sub 33}(1232) resonance form factor and R = {sigma}{sub L}/{sigma}{sub T}, the ratio of the longitudinal and transverse components of the cross section. A suggestion is made to study these quantities in conjunction with Bloom-Gilman duality.

Annual Site Environmental Report, 2007(ASER)

International Nuclear Information System (INIS)

Sabba, D

2008-01-01

This report provides information about environmental programs during the calendar year (CY) of 2007 at the Stanford Linear Accelerator Center (SLAC), Menlo Park, California. Activities that span the calendar year, i.e., stormwater monitoring covering the winter season of 2007/2008 (October 2007 through May 2008), are also included. Production of an annual site environmental report (ASER) is a requirement established by the United States Department of Energy (DOE) for all management and operating (M and O) contractors throughout the DOE complex. SLAC is a federally-funded research and development center with Stanford University as the M and O contractor. Under Executive Order (EO) 13423 and DOE Order 450.1, 'Environmental Protection Program', SLAC effectively implemented and integrated the key elements of an Environmental Management System (EMS) to achieve the site's integrated safety and environmental management system goals. For normal daily activities, SLAC managers and supervisors are responsible for ensuring that policies and procedures are understood and followed so that: (1) Worker safety and health are protected; (2) The environment is protected; and (3) Compliance is ensured. Throughout 2007, SLAC focused on development and implementation of SLAC management systems to ensure continual improvement. These systems provided a structured framework for SLAC to implement 'greening of the government' initiatives such as EO 13148. Overall, management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. SLAC continues to demonstrate significant progress in implementing and integrating EMS into day-to-day operations at SLAC. The annual management review and ranking of environmental aspects were completed this year by SLAC's EMS Steering Committee, the Environmental Safety Committee (ESC) and thirteen objectives and targets were established for 2007. For each objective and target, a work plan, or Environmental

Annual Site Environmental Report, 2007(ASER)

Energy Technology Data Exchange (ETDEWEB)

Sabba, D

2008-10-07

This report provides information about environmental programs during the calendar year (CY) of 2007 at the Stanford Linear Accelerator Center (SLAC), Menlo Park, California. Activities that span the calendar year, i.e., stormwater monitoring covering the winter season of 2007/2008 (October 2007 through May 2008), are also included. Production of an annual site environmental report (ASER) is a requirement established by the United States Department of Energy (DOE) for all management and operating (M&O) contractors throughout the DOE complex. SLAC is a federally-funded research and development center with Stanford University as the M&O contractor. Under Executive Order (EO) 13423 and DOE Order 450.1, 'Environmental Protection Program', SLAC effectively implemented and integrated the key elements of an Environmental Management System (EMS) to achieve the site's integrated safety and environmental management system goals. For normal daily activities, SLAC managers and supervisors are responsible for ensuring that policies and procedures are understood and followed so that: (1) Worker safety and health are protected; (2) The environment is protected; and (3) Compliance is ensured. Throughout 2007, SLAC focused on development and implementation of SLAC management systems to ensure continual improvement. These systems provided a structured framework for SLAC to implement 'greening of the government' initiatives such as EO 13148. Overall, management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. SLAC continues to demonstrate significant progress in implementing and integrating EMS into day-to-day operations at SLAC. The annual management review and ranking of environmental aspects were completed this year by SLAC's EMS Steering Committee, the Environmental Safety Committee (ESC) and thirteen objectives and targets were established for 2007. For each objective and target, a work

Ground motion measurements at the LBL Light Source site, the Bevatron and at SLAC

International Nuclear Information System (INIS)

Green, M.A.; Majer, E.I.; More, V.D.; O'Connell, D.R.; Shilling, R.C.

1986-12-01

This report describes the technique for measuring ground motion at the site of the 1.0 to 2.0 GeV Synchrotron Radiation Facility which was known as the Advanced Light Source (in 1983 when the measurements were taken). The results of ground motion measurements at the Light Source site at Building 6 at LBL are presented. As comparison, ground motion measurements were made at the Byerly Tunnel, the Bevatron, Blackberry Canyon, and SLAC at the Spear Ring. Ground Motion at the Light Source site was measured in a band from 4 to 100 Hz. The measured noise is primarily local in origin and is not easily transported through LBL soils. The background ground motion is for the most part less than 0.1 microns. Localized truck traffic near Building 6 and the operation of the cranes in the building can result in local ground motions of a micron or more for short periods of time. The background motion at Building 6 is between 1 and 2 orders of magnitude higher than ground motion in a quiet seismic tunnel, which is representative of quiet sites worldwide. The magnitude of the ground motions at SLAC and the Bevatron are comparable to ground motions measured at the Building 6 Light Source site. However, the frequency signature of each site is very different

Computing and data handling recent experiences at Fermilab and SLAC

International Nuclear Information System (INIS)

Cooper, P.S.

1990-01-01

Computing has become evermore central to the doing of high energy physics. There are now major second and third generation experiments for which the largest single cost is computing. At the same time the availability of ''cheap'' computing has made possible experiments which were previously considered infeasible. The result of this trend has been an explosion of computing and computing needs. I will review here the magnitude of the problem, as seen at Fermilab and SLAC, and the present methods for dealing with it. I will then undertake the dangerous assignment of projecting the needs and solutions forthcoming in the next few years at both laboratories. I will concentrate on the ''offline'' problem; the process of turning terabytes of data tapes into pages of physics journals. 5 refs., 4 figs., 4 tabs

Preparation of safety regulatory requirements for new technology like digital system

International Nuclear Information System (INIS)

Ito, Juichiro; Takita, Masami

2011-01-01

The current regulatory requirements on digital instrumentation and control system have been reviewed by JNES, considering international trend discussed in DICWG (Digital Instrumentation and Control Working Group) of MDEP (Multinational Design Evaluation Program). MDEP DICWG held in OECD/NEA (Organisation for Economic Co-operation and Development/Nuclear Energy Agency) gives the opportunity to identify the convergence of applicable standards. The working group's activities include: identifying and prioritising the member countries' challenges, practices, and needs regarding standards and regulatory guidance regarding digital instrumentation and control; identifying areas of importance and needs for convergence of existing standards and guidance or development of new standards; sharing of information; and identifying common positions among the member countries for areas of particular importance and need. The DICWG drafted common positions on specific issues which are based on the existing standards, national regulatory guidance, best practices, and group inputs using an agreed upon process and framework. Five general common positions are under discussion in this fiscal year. Simplicity in Design, Software Common Cause Failures, Software Tools, Data communication, Verification and Validation throughout the life cycle of safety systems using digital computers. In addition, the technical evaluation of standards of the Japan Electric Association about digital system for safety was made to support NISA (Nuclear and Industrial Safety Agency). (author)

Regulatory requirements on PSA level 2: Review, aspects and applications

International Nuclear Information System (INIS)

Husarcek, J.

2003-01-01

The general requirements concerning utility obligations, probabilistic safety criteria (CDF should not exceed 1.0E-4/reactor year and LERF should not exceed 1.0E-5/reactor year), documentation and results, living PSA requirements and major steps in level 2 PSA are presented. PSA developments in Slovakia, collection and assembly of information, plant damage states, containment performance and failure modes, severe accident progression analyses, containment failure modes and source terms as a part of performed level 2 PSA are discussed. The PSA applications in design and operation evaluation, support to plant upgrade and modifications are also described. At the end, the following conclusion is made: more extensive PSA application needs to foster the exchange of experience and communication between PSA specialists, non-PSA engineers, designers, and the regulatory body staff responsible for safety assessment, inspection and enforcement

Report of the working group 'Regulatory requirements on AM - Concept of nuclear and radiation safety during beyond-design-basis accidents'

International Nuclear Information System (INIS)

Bobaly, P.

2001-01-01

The developed working group report contains the following main paragraphs: legal basis and basis for regulatory requirements for on-site and off-site Accident Management (AM), regulatory requirements or recommendations for on-site AM and for emergency preparedness, background information concerning the implementation and review of an AM program as a basis for an AM guideline. Overview about AM/SAM implementation in member countries of the SAMINE project; measure and candidates for high level actions based upon US SAMG; interactions of severe accident research and the regulatory positions, relationship between different components of an accident management programme are also given

Regulatory requirements for nuclear power plant site selection in Malaysia-a review.

Science.gov (United States)

Basri, N A; Hashim, S; Ramli, A T; Bradley, D A; Hamzah, K

2016-12-01

Malaysia has initiated a range of pre-project activities in preparation for its planned nuclear power programme. Clearly one of the first steps is the selection of sites that are deemed suitable for the construction and operation of a nuclear power plant. Here we outline the Malaysian regulatory requirements for nuclear power plant site selection, emphasizing details of the selection procedures and site characteristics needed, with a clear focus on radiation safety and radiation protection in respect of the site surroundings. The Malaysia Atomic Energy Licensing Board (AELB) site selection guidelines are in accord with those provided in International Atomic Energy Agency (IAEA) and United Stated Nuclear Regulatory Commission (USNRC) documents. To enhance the suitability criteria during selection, as well as to assist in the final decision making process, possible assessments using the site selection characteristics and information are proposed.

Annual Site Environmental Report: 2008 (ASER)

International Nuclear Information System (INIS)

Sabba, D.

2009-01-01

This report provides information about environmental programs during the calendar year of 2008 at the SLAC National Accelerator Laboratory (SLAC), Menlo Park, California. Activities that span the calendar year, i.e., stormwater monitoring covering the winter season of 2008/2009 (October 2008 through May 2009), are also included. Production of an annual site environmental report (ASER) is a requirement established by the United States Department of Energy (DOE) for all management and operating (M and O) contractors throughout the DOE complex. SLAC is a federally-funded research and development center with Stanford University as the M and O contractor. Under Executive Order (EO) 13423, Strengthening Federal Environmental, Energy, and Transportation Management, and DOE Order 450.1A, Environmental Protection Program, SLAC effectively implements and integrates the key elements of an Environmental Management System (EMS) to achieve the site's integrated safety and environmental management system goals. For normal daily activities, SLAC managers and supervisors are responsible for ensuring that policies and procedures are understood and followed so that: (1) Worker safety and health are protected; (2) The environment is protected; and (3) Compliance is ensured. Throughout 2008, SLAC continued to improve its management systems. These systems provided a structured framework for SLAC to implement 'greening of the government' initiatives such as EO 13423 and DOE Orders 450.1A and 430.2B. Overall, management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. SLAC continues to demonstrate significant progress in implementing and integrating EMS into day-to-day operations and construction activities at SLAC. The annual management review and ranking of environmental aspects were completed this year by SLAC's EMS Steering Committee, the Environmental Safety Committee (ESC), and twelve objectives and targets were

Annual Site Environmental Report: 2009(ASER)

International Nuclear Information System (INIS)

2010-01-01

This report provides information about environmental programs during the calendar year of 2009 at the SLAC National Accelerator Laboratory (SLAC), Menlo Park, California. Activities that span the calendar year, i.e., stormwater monitoring covering the winter season of 2009/2010 (October 2009 through May 2010), are also included. Production of an annual site environmental report (ASER) is a requirement established by the United States Department of Energy (DOE) for all management and operating (M and O) contractors throughout the DOE complex. SLAC is a federally-funded research and development center with Stanford University as the M and O contractor. Under Executive Order (EO) 13423, Strengthening Federal Environmental, Energy, and Transportation Management, EO 13514, Federal Leadership in Environmental, Energy, and Economic Performance, and DOE Order 450.1A, Environmental Protection Program, SLAC effectively implements and integrates the key elements of an Environmental Management System (EMS) to achieve the site's integrated safety and environmental management system goals. For normal daily activities, SLAC managers and supervisors are responsible for ensuring that policies and procedures are understood and followed so that Worker safety and health are protected, The environment is protected, and Compliance is ensured. Throughout 2009, SLAC continued to improve its management systems. These systems provided a structured framework for SLAC to implement 'greening of the government' initiatives such as EO 13423, EO 13514, and DOE Orders 450.1A and 430.2B. Overall, management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. SLAC continues to demonstrate significant progress in implementing and integrating EMS into day-to-day operations and construction activities at SLAC. SLAC's EMS was audited by a review team from the DOE Oak Ridge Office and the DOE SLAC Site Office (SSO) on March 31, 2009. The review

Annual Site Environmental Report: 2008 (ASER)

Energy Technology Data Exchange (ETDEWEB)

Sabba, D.

2009-11-09

This report provides information about environmental programs during the calendar year of 2008 at the SLAC National Accelerator Laboratory (SLAC), Menlo Park, California. Activities that span the calendar year, i.e., stormwater monitoring covering the winter season of 2008/2009 (October 2008 through May 2009), are also included. Production of an annual site environmental report (ASER) is a requirement established by the United States Department of Energy (DOE) for all management and operating (M&O) contractors throughout the DOE complex. SLAC is a federally-funded research and development center with Stanford University as the M&O contractor. Under Executive Order (EO) 13423, Strengthening Federal Environmental, Energy, and Transportation Management, and DOE Order 450.1A, Environmental Protection Program, SLAC effectively implements and integrates the key elements of an Environmental Management System (EMS) to achieve the site's integrated safety and environmental management system goals. For normal daily activities, SLAC managers and supervisors are responsible for ensuring that policies and procedures are understood and followed so that: (1) Worker safety and health are protected; (2) The environment is protected; and (3) Compliance is ensured. Throughout 2008, SLAC continued to improve its management systems. These systems provided a structured framework for SLAC to implement 'greening of the government' initiatives such as EO 13423 and DOE Orders 450.1A and 430.2B. Overall, management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. SLAC continues to demonstrate significant progress in implementing and integrating EMS into day-to-day operations and construction activities at SLAC. The annual management review and ranking of environmental aspects were completed this year by SLAC's EMS Steering Committee, the Environmental Safety Committee (ESC), and twelve objectives and targets

A framework for regulatory requirements and industry standards for new nuclear power plants

International Nuclear Information System (INIS)

Duran, Felicia A.; Camp, Allen L.; Apostolakis, George E.; Golay, Michael W.

2000-01-01

This paper summarizes the development of a framework for risk-based regulation and design for new nuclear power plants. Probabilistic risk assessment methods and a rationalist approach to defense in depth are used to develop a framework that can be applied to identify systematically the regulations and standards required to maintain the desired level of safety and reliability. By implementing such a framework, it is expected that the resulting body of requirements will provide a regulatory environment that will ensure protection of the public, will eliminate the burden of requirements that do not contribute significantly to safety, and thereby will improve the market competitiveness of new plants. (author)

SLAC Scanner Processor applications in the data acquisition system for the upgraded Mark II detector

International Nuclear Information System (INIS)

Barklow, T.; Glanzman, T.; Lankford, A.J.; Riles, K.

1985-09-01

The SLAC Scanner Processor is a general purpose, programmable FASTBUS crate/cable master/slave module. This device plays a central role in the readout, buffering and pre-processing of data from the upgraded Mark II detector's new central drift chamber. In addition to data readout, the SSPs assist in a variety of other services, such as detector calibration, FASTBUS system management, FASTBUS system initialization and verification, and FASTBUS module testing. 9 refs., 1 fig., 2 tabs

SLC status and SLAC [Stanford Linear Accelerator Center] future plans

International Nuclear Information System (INIS)

Richter, B.

1989-08-01

In this presentation, I shall discuss the linear collider program at the Stanford Linear Accelerator Center as it is now, and as we hope to see it evolve over the next few years. Of greatest interest to the high energy accelerator physics community gathered here is the development of the linear collider concept, and so I shall concentrate most of this paper on a discussion of the present status and future evolution of the SLC. I will also briefly discuss the research and development program that we are carrying out aimed at the realization of the next generation of high-energy linear colliders. SLAC had a major colliding-beam storage-ring program as well, including present rings and design studies on future high-luminosity projects, but time constraints preclude a discussion of them. 8 figs., 3 tabs

Regulatory requirements and quality assurance of radiation monitoring instruments

International Nuclear Information System (INIS)

Narasimharao, K.L.; Sharma, Ranjit

2005-01-01

The successful utilisation of radiation sources in the fields of medicine and industry requires the accurate measurement of activity, exposure rate and dose. Many varieties of instruments are in use for measurement of these parameters and new ones are being developed. The criteria for the design of the radiation monitoring instrument include the type and intensity of the radiation, purpose of measurement and ruggedness of the instrument. Quality and reliability of radiation monitoring instruments ensure that individuals are adequately protected. Accuracy, response time and ruggedness are required to be as per the approved/ prescribed guidelines. Regulatory authorities outline the design and performance criteria for radiation monitoring instruments and prescribe the recommendations of international agencies such as IAEA, ICRU and ISO for radiological measurement assurance programme. National Standards Laboratories all over the world prescribe procedures for calibration of various radiation monitoring instruments. The instruments should be calibrated as per these guidelines and should be traceable to national standards. The calibration traceable to national/ international standards and documentation as well as limits stipulated by the competent authority ensures the expected performance of the instrument. (author)

Development of Regulatory Technical Requirements for the Advanced Integral Type Research Reactor

International Nuclear Information System (INIS)

Jo, Jong Chull; Yune, Young Gill; Kim, Woong Sik; Kim, Hho Jung

2004-01-01

This paper presents the current status of the study on the development of regulatory technical requirements for the licensing review of an advanced integral type research reactor of which the license application is expected in a few years. According to the Atomic Energy Act of Korea, both research and education reactors are subject to the technical requirements for power reactors in the licensing review. But, some of the requirements may not be applicable or insufficient for the licensing reviews of reactors with unique design features. Thus it is necessary to identify which review topics or areas can not be addressed by the existing requirements and to develop the required ones newly or supplement appropriately. Through the study performed so far, it has been identified that the following requirements need to be developed newly for the licensing review of SMART-P: the use of proven technology, the interfacial facility, the non-safety systems, and the metallic fuels. The approach and basis for the development of each of the requirements are discussed. (authors)

Regulatory requirements for replacement of analog systems with digital upgrades

International Nuclear Information System (INIS)

Loeser, P.J.

1993-01-01

This paper reviews briefly the regulatory guidelines which must be met in order to replace analog systems in nuclear power plants with digital systems. There is a move to do such replacements for a number of reasons: analog systems are aging, and showing considerable drift; few vendors manufacture analog systems today; support and parts are hard to get; digital systems provide flexibility. There is a safety concern however about undesirable and unpredictable effects to digital safety equipment due to plant transients, accidents, post-accident condition, and EMI/RF environmental interferences. License holders must comply with the requirements of 10 C.F.R. 50.59, which deals with safety concerns with respect to any changes to operating plants which may have an impact on the safety of the plant. NRC staff is taking the position that all digital upgrades will require an evaluation under this regulation

Short wavelength FELs using the SLAC linac

International Nuclear Information System (INIS)

Winick, H.; Bane, K.; Boyce, R.

1993-08-01

Recent technological developments have opened the possibility to construct a device which we call a Linac Coherent Light Source (LCLS); a fourth generation light source, with brightness, coherence, and peak power far exceeding other sources. Operating on the principle of the free electron laser (FEL), the LCLS would extend the range of FEL operation to much aborter wavelength than the 240 mn that has so far been reached. We report the results of studies of the use of the SLAC linac to drive an LCLS at wavelengths from about 3-100 nm initially and possibly even shorter wavelengths in the future. Lasing would be achieved in a single pass of a low emittance, high peak current, high energy electron beam through a long undulator. Most present FELs use an optical cavity to build up the intensity of the light to achieve lasing action in a low gain oscillator configuration. By eliminating the optical cavity, which is difficult to make at short wavelengths, laser action can be extended to shorter wavelengths by Self-Amplified-Spontaneous-Emission (SASE), or by harmonic generation from a longer wavelength seed laser. Short wavelength, single pass lasers have been extensively studied at several laboratories and at recent workshops

Regulatory requirements for the use of consumer products containing radioactive substances

International Nuclear Information System (INIS)

Mason, G.C.; Paynter, R.A.; Schmitt-Hannig, A.; Sztanyik, L.B.

1996-01-01

In almost 100 years since the discovery of radioactivity, the properties of radioactive materials have been exploited in products such as clocks and watches incorporating luminous paint which are freely available to members of the public. Over time, regulatory authorities have felt it necessary to apply some degree of control to the supply and use of such products in order to protect public health. In many areas of radiation protection, national authorities take note of international recommendations when developing national standards, but the existing detailed guidance of the International Atomic Energy Agency (IAEA) for consumer products is incomplete and out of date. Recently, a thorough revision of the International Basic Safety Standards (BSS) has occurred, which has prompted a review and revision of the related guidance published by the IAEA. A draft Guide on Regulatory Requirements for the Use of Consumer Products Containing Radioactive Substances has now been completed and is currently under review within the IAEA's system for development of documents in its Safety Series of publications. (author)

Setup and Calibration of SLAC's Peripheral Monitoring Stations

Energy Technology Data Exchange (ETDEWEB)

Cooper, C.

2004-09-03

The goals of this project were to troubleshoot, repair, calibrate, and establish documentation regarding SLAC's (Stanford Linear Accelerator Center's) PMS (Peripheral Monitoring Station) system. The PMS system consists of seven PMSs that continuously monitor skyshine (neutron and photon) radiation levels in SLAC's environment. Each PMS consists of a boron trifluoride (BF{sub 3}) neutron detector (model RS-P1-0802-104 or NW-G-20-12) and a Geiger Moeller (GM) gamma ray detector (model TGM N107 or LND 719) together with their respective electronics. Electronics for each detector are housed in Nuclear Instrument Modules (NIMs) and are plugged into a NIM bin in the station. All communication lines from the stations to the Main Control Center (MCC) were tested prior to troubleshooting. To test communication with MCC, a pulse generator (Systron Donner model 100C) was connected to each channel in the PMS and data at MCC was checked for consistency. If MCC displayed no data, the communication cables to MCC or the CAMAC (Computer Automated Measurement and Control) crates were in need of repair. If MCC did display data, then it was known that the communication lines were intact. All electronics from each station were brought into the lab for troubleshooting. Troubleshooting usually consisted of connecting an oscilloscope or scaler (Ortec model 871 or 775) at different points in the circuit of each detector to record simulated pulses produced by a pulse generator; the input and output pulses were compared to establish the location of any problems in the circuit. Once any problems were isolated, repairs were done accordingly. The detectors and electronics were then calibrated in the field using radioactive sources. Calibration is a process that determines the response of the detector. Detector response is defined as the ratio of the number of counts per minute interpreted by the detector to the amount of dose equivalent rate (in mrem per hour, either calculated

Characterizing costs and benefits of uncertain future regulatory requirements on the U.S. natural gas industry

International Nuclear Information System (INIS)

Godec, M.L.; Smith, G.E.; Fitzgibbon, T.

1995-01-01

Environmental regulatory requirements at both the state and federal level are constantly changing, making it difficult for industry and R ampersand D program managers to project future compliance requirements and costs. Even if a company is trying to keep abreast of various proposed regulatory initiatives, the number of possible combinations of initiatives that could occur in the future seems virtually limitless. Uncertainty associated with potential future environmental compliance requirements makes the identification and evaluation of future investment and R ampersand D opportunities exceedingly difficult, and makes the process of systematic strategic planning increasingly complex. This paper describes a methodology for accounting for uncertain future environmental compliance costs in a systematic, comprehensive manner. Through analysis of proposed initiatives for making future environmental requirements more stringent, forecasting the likelihood of occurrence and potential timing of each initiative, and estimating potential future compliance costs associated with each initiative, a thorough process for incorporating regulatory uncertainty into strategic planning and project evaluation is described. This approach can be used for evaluating R ampersand D opportunities to determine where development of new technologies or assessment of risks posed by industry operations may have the greatest impact on future industry costs of compliance. This approach could also be used to account for the uncertainty of future environmental costs in corporate strategic planning or for factoring future compliance costs into project evaluation. This approach could also be enhanced through use in conjunction with other modeling and forecasting systems that could consider a broad range of impacts, including impacts on gas production, industry activity levels, and tax revenues

HEP Science Network Requirements--Final Report

Energy Technology Data Exchange (ETDEWEB)

Bakken, Jon; Barczyk, Artur; Blatecky, Alan; Boehnlein, Amber; Carlson, Rich; Chekanov, Sergei; Cotter, Steve; Cottrell, Les; Crawford, Glen; Crawford, Matt; Dart, Eli; Dattoria, Vince; Ernst, Michael; Fisk, Ian; Gardner, Rob; Johnston, Bill; Kent, Steve; Lammel, Stephan; Loken, Stewart; Metzger, Joe; Mount, Richard; Ndousse-Fetter, Thomas; Newman, Harvey; Schopf, Jennifer; Sekine, Yukiko; Stone, Alan; Tierney, Brian; Tull, Craig; Zurawski, Jason

2010-04-27

-Atlantic connectivity is more complex than network engineering for intra-US connectivity. This is because transoceanic circuits have lower reliability and longer repair times when compared with land-based circuits. Therefore, trans-Atlantic connectivity requires greater deployed bandwidth and diversity to ensure reliability and service continuity of the user-level required data transfer rates. (4) Trans-Atlantic traffic load and patterns must be monitored, and projections adjusted if necessary. There is currently a shutdown planned for the LHC in 2012 that may affect projections of trans-Atlantic bandwidth requirements. (5) There is a significant need for network tuning and troubleshooting during the establishment of new LHC Tier-2 and Tier-3 facilities. ESnet will work with the HEP community to help new sites effectively use the network. (6) SLAC is building the CCD camera for the LSST. This project will require significant bandwidth (up to 30Gbps) to NCSA over the next few years. (7) The accelerator modeling program at SLAC could require the movement of 1PB simulation data sets from the Leadership Computing Facilities at Argonne and Oak Ridge to SLAC. The data sets would need to be moved overnight, and moving 1PB in eight hours requires more than 300Gbps of throughput. This requirement is dependent on the deployment of analysis capabilities at SLAC, and is about five years away. (8) It is difficult to achieve high data transfer throughput to sites in China. Projects that need to transfer data in or out of China are encouraged to deploy test and measurement infrastructure (e.g. perfSONAR) and allow time for performance tuning.

HEP Science Network Requirements. Final Report

International Nuclear Information System (INIS)

Dart, Eli; Tierney, Brian

2010-01-01

is more complex than network engineering for intra-US connectivity. This is because transoceanic circuits have lower reliability and longer repair times when compared with land-based circuits. Therefore, trans-Atlantic connectivity requires greater deployed bandwidth and diversity to ensure reliability and service continuity of the user-level required data transfer rates. (4) Trans-Atlantic traffic load and patterns must be monitored, and projections adjusted if necessary. There is currently a shutdown planned for the LHC in 2012 that may affect projections of trans-Atlantic bandwidth requirements. (5) There is a significant need for network tuning and troubleshooting during the establishment of new LHC Tier-2 and Tier-3 facilities. ESnet will work with the HEP community to help new sites effectively use the network. (6) SLAC is building the CCD camera for the LSST. This project will require significant bandwidth (up to 30Gbps) to NCSA over the next few years. (7) The accelerator modeling program at SLAC could require the movement of 1PB simulation data sets from the Leadership Computing Facilities at Argonne and Oak Ridge to SLAC. The data sets would need to be moved overnight, and moving 1PB in eight hours requires more than 300Gbps of throughput. This requirement is dependent on the deployment of analysis capabilities at SLAC, and is about five years away. (8) It is difficult to achieve high data transfer throughput to sites in China. Projects that need to transfer data in or out of China are encouraged to deploy test and measurement infrastructure (e.g. perfSONAR) and allow time for performance tuning.

The major cellular sterol regulatory pathway is required for Andes virus infection.

Directory of Open Access Journals (Sweden)

Josiah Petersen

2014-02-01

Full Text Available The Bunyaviridae comprise a large family of RNA viruses with worldwide distribution and includes the pathogenic New World hantavirus, Andes virus (ANDV. Host factors needed for hantavirus entry remain largely enigmatic and therapeutics are unavailable. To identify cellular requirements for ANDV infection, we performed two parallel genetic screens. Analysis of a large library of insertionally mutagenized human haploid cells and a siRNA genomic screen converged on components (SREBP-2, SCAP, S1P and S2P of the sterol regulatory pathway as critically important for infection by ANDV. The significance of this pathway was confirmed using functionally deficient cells, TALEN-mediated gene disruption, RNA interference and pharmacologic inhibition. Disruption of sterol regulatory complex function impaired ANDV internalization without affecting virus binding. Pharmacologic manipulation of cholesterol levels demonstrated that ANDV entry is sensitive to changes in cellular cholesterol and raises the possibility that clinically approved regulators of sterol synthesis may prove useful for combating ANDV infection.

Single-bunch beam loading on the SLAC two-mile accelerator

International Nuclear Information System (INIS)

Koontz, R.F.

1976-05-01

The experiments described were initially prompted by interest in the radiation loss of relativistic electron rings passing through periodic structures. Later the same experiments became relevant to the theory of energy loss of electrons in large storage rings. In both of these cases energy loss to the higher order modes of the respective structures could seriously limit their effective operation. In these experiments, single bunches of electrons with intensities up to 7 x 10 8 electrons per bunch are accelerated through the SLAC three-kilometer accelerator, and their energy spectra are analyzed. Early experiments over a wide energy range (900 MeV to 19 GeV) demonstrated that the energy loss was proportional to the total charge in the bunch but was independent of beam energy. The average energy loss of a single bunch normalized to 10 9 electrons was initially measured to be 38 MeV

Status of the SLAC/LBL/LLNL B-Factory and the BaBar detector

International Nuclear Information System (INIS)

Oddone, P.

1994-08-01

The primary motivation of the Asymmetric B-Factory is the study of CP violation. The decay of B mesons and, in particular, the decay of neutral B mesons, offers the possibility of determining conclusively whether CP violation is part and parcel of the Standard Model with three generations of quarks and leptons. Alternatively, the authors may discover that CP violation lies outside the present framework. In this paper the authors briefly describe the physics reach of the SLAC/LBL/LLNL Asymmetric B-Factory, the progress on the machine design and construction, the progress on the detector design, and the schedule to complete both projects

The optical design of the spin manipulation system for the SLAC Linear Collider

International Nuclear Information System (INIS)

Fieguth, T.H.

1989-03-01

The optical design of the beam transport lines between the SLAC Linac and the electron damping ring and the design of part of the Linac lattice itself will be modified to accommodate three superconducting solenoids for the purpose of manipulating the polarization of the electron beam. In order to allow arbitrary orientation of the polarization vector, this design will be capable of compensating the fields of two independent solenoids for arbitrary strengths ranging to 7.0 T-m. The method of dealing with the coupling of the betatron functions and the method of handling both the electron and positron beams in the common region are discussed. 8 refs., 5 figs

A simplified ALARA approach to demonstration of compliance with surface contaminated object regulatory requirements

International Nuclear Information System (INIS)

Pope, R.B.; Shappert, L.B.; Michelhaugh, R.D.; Boyle, R.W.; Cook, J.C.

1998-02-01

The US Department of Transportation (DOT) and the US Nuclear Regulatory Commission (NRC) have jointly prepared a comprehensive set of draft guidance for consignors and inspectors to use when applying the newly imposed regulatory requirements for low specific activity (LSA) material and surface contaminated objects (SCOs). The guidance is being developed to facilitate compliance with the new LSA material and SCO requirements, not to impose additional requirements. These new requirements represent, in some areas, significant departures from the manner in which packaging and transportation of these materials and objects were previously controlled. On occasion, it may be appropriate to use conservative approaches to demonstrate compliance with some of the requirements, ensuring that personnel are not exposed to radiation at unnecessary levels, so that exposures are kept as low as reasonably achievable (ALARA). In the draft guidance, one such approach would assist consignors preparing a shipment of a large number of SCOs in demonstrating compliance without unnecessarily exposing personnel. In applying this approach, users need to demonstrate that four conditions are met. These four conditions are used to categorize non-activated, contaminated objects as SCO-2. It is expected that, by applying this approach, it will be possible to categorize a large number of small contaminated objects as SCO-2 without the need for detailed, quantitative measurements of fixed, accessible contamination, or of total (fixed and non-fixed) contamination on inaccessible surfaces. The method, which is based upon reasoned argument coupled with limited measurements and the application of a sum of fractions rule, is described and examples of its use are provided

PEP-II Large Power Supplies Rebuild Program at SLAC

CERN Document Server

de Lira, Antonio C; Lipari, James J; da Silva Rafael, Fernando

2005-01-01

At PEP-II, seven large power supplies (LGPS) are used to power quad magnets in the electron-positron collider region. The LGPS ratings range from 72kW to 270kW, and were installed in 1997. They are unipolar off-line switch mode supplies, with a 6 pulse bridge rectifying 480VAC, 3-phase input power to yield 650VDC unregulated. This unregulated 650VDC is then input into one (or two) IGBT H-bridges, which convert the DC into PWM 16 kHz square wave AC. This high frequency AC drives the primary side of a step-down transformer followed by rectifiers and low pass filters. Over the years, these LGPS have presented many problems mainly in their control circuits, making it difficult to troubleshoot and affecting the overall accelerator availability. A redesign/rebuilding program for these power supplies was established under the coordination of the Power Conversion Department at SLAC. During the 2004 accelerator summer shutdown all the control circuits in these supplies were redesigned and replaced. A new PWM control b...

Information Management system of the safety regulatory requirements and guidance for the Korea next generation reactors

International Nuclear Information System (INIS)

Yun, Y. C.; Lee, J. H.; Lee, H. C.; Lee, J. S.

2000-01-01

In order to achieve the safety of the Korea Next Generation Reactors (KNGR), the Korea Institute of Nuclear Safety has carried out the Safety and Regulatory Requirements and Guidance (SRRG) development program from 1992 such as establishment of the SRRG hierarchy, development of technical requirements and guidance, and consideration of new licensing system. The SRRG hierarchy for the KNGR was consisted of five tiers; Safety Objectives, Safety Principles, General Safety Criteria, Specific Safety Requirements and Safety Regulatory Guides. The developed SRRG have been compared the criteria in 10CFR and Reg. Guide in the U.S.A and the IAEA documents for assuring internationally acceptable level of the SRRG. To improve the efficiency and accuracy of SRRG development, the construction of database system was required in the course of development. Therefore, the Information Management System of SRRG for the KNGR has been developed which enables developers to quickly and accurately seek and systematically manage whole contexts of the SRRG, reference requirements, and current atomic energy regulation rules. Moreover, through homepage whose URL is 'http://kngr.kins.re.kr', the concerned persons and public can acquire the information related with SRRG and KNGR project, and post his/her thought to the opinion forum in the homepage

Information Management system of the safety regulatory requirements and guidance for the Korea next generation reactors

Energy Technology Data Exchange (ETDEWEB)

Yun, Y. C. [LG-EDS Systems, Seoul (Korea, Republic of); Lee, J. H.; Lee, H. C.; Lee, J. S. [Korea Institute of Nuclear Safety, Taejon (Korea, Republic of)

2000-05-01

In order to achieve the safety of the Korea Next Generation Reactors (KNGR), the Korea Institute of Nuclear Safety has carried out the Safety and Regulatory Requirements and Guidance (SRRG) development program from 1992 such as establishment of the SRRG hierarchy, development of technical requirements and guidance, and consideration of new licensing system. The SRRG hierarchy for the KNGR was consisted of five tiers; Safety Objectives, Safety Principles, General Safety Criteria, Specific Safety Requirements and Safety Regulatory Guides. The developed SRRG have been compared the criteria in 10CFR and Reg. Guide in the U.S.A and the IAEA documents for assuring internationally acceptable level of the SRRG. To improve the efficiency and accuracy of SRRG development, the construction of database system was required in the course of development. Therefore, the Information Management System of SRRG for the KNGR has been developed which enables developers to quickly and accurately seek and systematically manage whole contexts of the SRRG, reference requirements, and current atomic energy regulation rules. Moreover, through homepage whose URL is 'http://kngr.kins.re.kr', the concerned persons and public can acquire the information related with SRRG and KNGR project, and post his/her thought to the opinion forum in the homepage.

Data Quality Objectives for Regulatory Requirements for Dangerous Waste Sampling and Analysis

International Nuclear Information System (INIS)

MULKEY, C.H.

1999-01-01

This document describes sampling and analytical requirements needed to meet state and federal regulations for dangerous waste (DW). The River Protection Project (RPP) is assigned to the task of storage and interim treatment of hazardous waste. Any final treatment or disposal operations, as well as requirements under the land disposal restrictions (LDRs), fall in the jurisdiction of another Hanford organization and are not part of this scope. The requirements for this Data Quality Objective (DQO) Process were developed using the RPP Data Quality Objective Procedure (Banning 1996), which is based on the U.S. Environmental Protection Agency's (EPA) Guidance for the Data Quality Objectives Process (EPA 1994). Hereafter, this document is referred to as the DW DQO. Federal and state laws and regulations pertaining to waste contain requirements that are dependent upon the composition of the waste stream. These regulatory drivers require that pertinent information be obtained. For many requirements, documented process knowledge of a waste composition can be used instead of analytical data to characterize or designate a waste. When process knowledge alone is used to characterize a waste, it is a best management practice to validate the information with analytical measurements

Annual Site Environmental Report: 2009(ASER)

Energy Technology Data Exchange (ETDEWEB)

2010-10-01

This report provides information about environmental programs during the calendar year of 2009 at the SLAC National Accelerator Laboratory (SLAC), Menlo Park, California. Activities that span the calendar year, i.e., stormwater monitoring covering the winter season of 2009/2010 (October 2009 through May 2010), are also included. Production of an annual site environmental report (ASER) is a requirement established by the United States Department of Energy (DOE) for all management and operating (M&O) contractors throughout the DOE complex. SLAC is a federally-funded research and development center with Stanford University as the M&O contractor. Under Executive Order (EO) 13423, Strengthening Federal Environmental, Energy, and Transportation Management, EO 13514, Federal Leadership in Environmental, Energy, and Economic Performance, and DOE Order 450.1A, Environmental Protection Program, SLAC effectively implements and integrates the key elements of an Environmental Management System (EMS) to achieve the site's integrated safety and environmental management system goals. For normal daily activities, SLAC managers and supervisors are responsible for ensuring that policies and procedures are understood and followed so that Worker safety and health are protected, The environment is protected, and Compliance is ensured. Throughout 2009, SLAC continued to improve its management systems. These systems provided a structured framework for SLAC to implement 'greening of the government' initiatives such as EO 13423, EO 13514, and DOE Orders 450.1A and 430.2B. Overall, management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. SLAC continues to demonstrate significant progress in implementing and integrating EMS into day-to-day operations and construction activities at SLAC. SLAC's EMS was audited by a review team from the DOE Oak Ridge Office and the DOE SLAC Site Office (SSO) on March 31, 2009

78 FR 76757 - Regulatory Guidance on Hours of Service of Drivers Rest Break Requirement; Drivers Who Become...

Science.gov (United States)

2013-12-19

... limitations for unforeseen reasons, is the driver in violation of the Sec. 395.3 rest break provision if more... unforeseen reasons, is not in violation of the Sec. 395.3 rest-break requirements if 8 or more hours have... Regulatory Guidance on Hours of Service of Drivers Rest Break Requirement; Drivers Who Become Ineligible for...

Development of guidance on applications of regulatory requirements for low specific activity materials and surface contaminated objects

International Nuclear Information System (INIS)

Pope, R.B.; Easton, E.P.; Shankman, S.F.

1997-01-01

In 1985, the International Atomic Energy Agency issued revised regulations for the safe transport of radioactive material. Significant among the changes were major revisions to requirements for Low Specific Activity (LSA) material and Surface Contaminated Objects (SCOs). In preparation for the adoption of these requirements into regulations in the United States, it became apparent that guidance on how to apply these requirements, clarifying technical uncertainties and ensuring proper implementation, would be needed both by the regulators and those regulated. Thus, the US Department of Transportation and the US Nuclear Regulatory Commission, with the assistance of staff from Oak Ridge National Laboratory, are preparing regulatory guidance for LSA material and SCO transport. The guidance will present examples of acceptable methods for demonstrating compliance with the revised rules. Ideas being investigated for inclusion in the pending guidance are discussed in this paper. Under current plans, the guidance will be issued for public comment prior to final issuance of the guidance in 1997

Development of guidance on applications of regulatory requirements for low specific activity materials and surface contaminated objects

International Nuclear Information System (INIS)

Pope, R.B.; Easton, E.P.; Shankman, S.F.; Boyle, R.W.

1997-01-01

In 1985, the International Atomic Energy Agency issued revised regulations for the safe transport of radioactive material. Significant among the changes were major revisions to requirements for Low Specific Activity (LSA) material and Surface Contaminated Objects (SCOs). In preparation for the adoption of these requirements into regulations in the United States, it became apparent that guidance on how to apply these requirements, clarifying technical uncertainties and ensuring proper implementation, would be needed both by the regulators and those regulated. Thus, the US Department of Transportation and the U.S. Nuclear Regulatory Commission, with the assistance of staff from Oak Ridge National Laboratory, are preparing regulatory guidance for LSA material and SCO transport. The guidance will present examples of acceptable methods for demonstrating compliance with the revised rules. Ideas being investigated for inclusion in the pending guidance are discussed in this paper. Under current plans, the guidance will be issued for public comment prior to final issue of the guidance in 1997. (Author)

SLAC/DESY International Workshop on Interactions of Intense Sub-Picosecond X-Rays with Matter, Stanford, CA, January 23-24, 1997

International Nuclear Information System (INIS)

Tatchyn, Roman

1998-01-01

This is the proceedings volume of the 1997 SLAC/DESY International Workshop on Interactions of Intense Sub-picosecond X-Ray Pulses with Matter. The workshop theme evolved out of design and R and D studies, undertaken at SLAC, DESY, and elsewhere [1,2], of the new class of linac-driven X-Ray Free Electron Lasers (XRFELs) operating with photocathode-based, low-emittance electron beams in the Self-Amplified Spontaneous Emission (SASE) regime [3]. It can be noted that, following the conclusion of the workshop, funded design study reports on R and D facilities based on these novel sources have been completed and published by both laboratories [4,5]. Topical significance was imparted to the workshop agenda by a series of prior workshops organized to explore scientific and technological applications of linac driven XRFELs [6,7,8,9]. These served to highlight underlying concerns regarding the potential loading effects of the highly intense radiation pulses from this new class of light source on the instrumentation, samples, and experimental phenomena being considered. The primary objectives of the workshop were: (a) to provide tutorial overviews of existing theoretical, numerical, and experimental techniques in the study of interactions of intense, ultra-short radiation pulses with matter, and of their applicability to the parameter regimes of the SLAC and DESY XRFELs; (b) to discuss practical optics and instrumentation issues related to peak and average power density loading; (c) to identify and explore novel concepts and design approaches, with an emphasis on optical instrumentation and experimental physics; (d) to formulate independent or collaborative R and D programs and activities in the areas of theory, numerical simulation, and experimental physics relevant to the linac-driven XRFEL parameter regime

Federal and state regulatory requirements for the D ampersand D of the Alpha-4 Building, Y-12 Plant, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

Etnier, E.L.; Houlberg, L.M.; Bock, R.E.

1994-01-01

The US Department of Energy (DOE) has begun the decontamination and decommissioning (D ampersand D) of Building 9201-4 (Alpha-4) at the Oak Y-12 Plant, Oak Ridge, Tennessee, The Alpha-4 Building was used from 1953--1962 to house a column exchange (Colex) process for lithium isotope separation. This process involved electrochemical and solvent extraction processes that required substantial quantities of mercury. Presently there is no law or regulation mandating decommissioning at DOE facilites or setting de minimis or ''below regulatory concern'' (BRC) radioactivity levels to guide decommissioning activities at DOE facilities. However, DOE Order 5820.2A, Chap. V (Decommissioning of Radioactively Contaminated Facilities), requires that the regulatory status of each project be identified and that technical engineering planning must assure D ampersand D compliance with all environmental regulations during cleanup activities. To assist in the performance of this requirement, this paper gives a brief overview of potential federal and state regulatory requirements related to D ampersand D activities at Alpha-4. Compliance with other federal, state, and local regulations not addressed here may be required, depending on site characterization, actual D ampersand D activities, and wastes generated

The Defence in Depth Concept Applied to the New Regulatory Requirements in Japan

Energy Technology Data Exchange (ETDEWEB)

Yamagata, H., E-mail: hiroshi_yamagata@nsr.go.jp [Nuclear Regulation Authority, Minato-ku, Tokyo (Japan)

2014-10-15

Full text: The new regulatory requirements based on lessons learnt from Fukushima Daiichi accident, which places emphasis on Defense-in-Depth concept, was put into effect in Japan on 8th July, 2013. It is required to prepare multi-layered protective measures. Each layer should achieve the objective only in that layer regardless of the measures in the other layers. The challenge is how to enhance independence of measures between layers. In the third layer, the current concept of design regarding safety relies on “single failure”, whose condition is elimination of common cause failure (CCF). To eliminate CCFs we introduced a more accurate approach in assessment of earthquake and tsunami, and introduction of measures against tsunami inundation. Redundancy of safety systems could not eliminate CCF by extreme natural hazards. Safety system should be designed by due consideration of diversity and independence including spatial dispersement. In the fourth layer, multi-layered protective measures are also applied for severe accidents, which consists of “prevention of core damage” under multiple failure, “prevention of containment failure”, and “prevention of large release, that is controlled release by venting”. In the fifth layer, we also require operators to prepare measures for “suppression of radioactive materials dispersion”. Of course, off-site emergency preparedness and response has been enhanced by introduction of PAZ and UPZ. Introduction of “Specialized Safety Facility” against intentional aircraft crash will contribute enhancement of some layers by providing electricity and water under extremely severe conditions. The new regulatory requirements are not our goal, just a first step. It is expected for regulator and operators to improve safety continuously by periodic comprehensive safety assessments including IPE, IPEEE, Margin test, and etc. We have to make an upward spiral of nuclear safety. (author)

Regulatory Safety Requirements for Operating Nuclear Installations

International Nuclear Information System (INIS)

Gubela, W.

2017-01-01

The National Nuclear Regulator (NNR) is established in terms of the National Nuclear Regulator Act (Act No 47 of 1999) and its mandate and authority are conferred through sections 5 and 7 of this Act, setting out the NNR's objectives and functions, which include exercising regulatory control over siting, design, construction etc of nuclear installations through the granting of nuclear authorisations. The NNR's responsibilities embrace all those actions aimed at providing the public with confidence and assurance that the risks arising from the production of nuclear energy remain within acceptable safety limits -> Therefore: Set fundamental safety standards, conducting pro-active safety assessments, determining licence conditions and obtaining assurance of compliance. The promotional aspects of nuclear activities in South Africa are legislated by the Nuclear Energy Act (Act No 46 of 1999). The NNR approach to regulations of nuclear safety and security take into consideration, amongst others, the potential hazards associated with the facility or activity, safety related programmes, the importance of the authorisation holder's safety related processes as well as the need to exercise regulatory control over the technical aspects such as of the design and operation of a nuclear facility in ensuring nuclear safety and security. South Africa does not have national nuclear industry codes and standards. The NNR is therefore non-prescriptive as it comes to the use of industry codes and standards. Regulatory framework (current) provide for the protection of persons, property, and environment against nuclear damage, through Licensing Process: Safety standards; Safety assessment; Authorisation and conditions of authorisation; Public participation process; Compliance assurance; Enforcement

The Spin Structure Function of the Proton from SLAC Experiment E155

Energy Technology Data Exchange (ETDEWEB)

McKee, P

2004-02-17

Experiment E155 at the Stanford Linear Accelerator Center (SLAC) measured the longitudinal and transverse deep inelastic structure functions of the proton and deuteron using a polarized, 48.3 GeV electron beam and solid polarized targets of ammonia ({sup 15}NH{sub 3}) for proton measurements and lithium deuteride ({sup 6}Li{sup 2}H) for deuteron measurements. Three electromagnetic spectrometers at angles of 2.75{sup o}, 5.5{sup o}, and 10.5{sup o} measured the scattered electrons. This work presents an analysis of the longitudinal structure function of the proton, g{sub 1}{sup p}(x, Q{sup 2}). Included is a re-analysis of the proton target polarization data that for the first time corrects a problem encountered which altered those measurements.

Production and decay of Z bosons at the SLC [SLAC Linear Collider

International Nuclear Information System (INIS)

Feldman, G.J.

1989-12-01

My lectures at Cargese covered the very first physics results from the SLAC Linear Collider (SLC). At the time of this writing (December 1989), it seems most sensible to present a review of the results that were presented at the school in an updated form. The organization of this report will be to give a brief introduction to linear colliders and the SLC, then to describe the MARK II detector, and finally to review the current status of the three major physics topics discussed at Cargese: the Z line shape, from which we deduce the Z mass and width, and the number of neutrino species, the partonic structure of hadronic decays and a measurement of α s , and searches for new quarks and leptons. 39 refs., 27 figs., 3 tabs

Measurement of the Left-Right Asymmetry in Z0 Events at SLAC

Energy Technology Data Exchange (ETDEWEB)

Szumilo, A

2004-01-05

Recent results from the 1992 and 1993 left-right asymmetry cross section measurements at the Stanford Linear Accelerator Center are presented. Measurements made with SLAC running with a center-of-mass energy at the Z{sup 0}-pole (91.2 GeV) by the SLD detector and an average electron beam polarization of 22.4 {+-} 0.7% for 1992 and 62.6 {+-} 1.2% for 1993. The asymmetry measured was A{sub LR} = 0.100 {+-} 0.044 and A{sub LR} = 0.1656 {+-} 0.0073 for the 1992 and 1993 runs, respectively. This in turn allows them to calculate the weak mixing angle value of sin{sup 2} {theta}{sub W} = 0.2378 {+-} 0.0056 and sin{sup 2} {theta}{sub W} = 0.2288 {+-} 0.0009 for the two data sets.

Highlights of the SLD Physics Program at the SLAC Linear Collider

International Nuclear Information System (INIS)

Willocq, Stephane

2001-01-01

Starting in 1989, and continuing through the 1990s, high-energy physics witnessed a flowering of precision measurements in general and tests of the standard model in particular, led by e + e - collider experiments operating at the Z 0 resonance. Key contributions to this work came from the SLD collaboration at the SLAC Linear Collider. By exploiting the unique capabilities of this pioneering accelerator and the SLD detector, including a polarized electron beam, exceptionally small beam dimensions, and a CCD pixel vertex detector, SLD produced a broad array of electroweak, heavy-flavor, and QCD measurements. Many of these results are one of a kind or represent the world's standard in precision. This article reviews the highlights of the SLD physics program, with an eye toward associated advances in experimental technique, and the contribution of these measurements to our dramatically improved present understanding of the standard model and its possible extensions

Fuel utilization experience in Bohunice NPP and regulatory requirements for implementation of progressive fuel management strategies

Energy Technology Data Exchange (ETDEWEB)

Patenyi, V [Nuclear Regulatory Authority, Bratislava (Slovakia); Darilek, P; Majercik, J [Vyskumny Ustav Jadrovych Elektrarni, Trnava (Slovakia)

1994-12-31

The experience gained in fuel utilization and the basic requirements for fuel licensing in the Slovak NPPs is described. The original project of WWER-440 reactors supposes 3-year fuel cycle with cycle length of about 320 full power days (FPD). Since 1984 it was reduced to 290 FPD. Based on the experience of other countries, a 4-year fuel cycle utilization started in 1987. It is illustrated with data from the Bohunice NPP units. Among 504 fuel assemblies left for the fourth burnup cycle no leakage was observed. The mean burnup achieved in the different units varied from 33.1 to 38.5 Mwd/kg U. The new fuel assemblies used are different from the recent ones in construction, thermohydraulics, water-uranium ratio, enrichment and material design. To meet the safety criteria, regulatory requirements for exploitation of new fuel in WWER-440 were formulated by the Nuclear Regulatory Authority of Slovak Republic. 1 tab., 5 refs.

Study of the doubly-charmed decays of B mesons with the experiment BABAR in SLAC; Etude des desintegrations doublement charmees des mesons B avec l'experience BABAR a SLAC

Energy Technology Data Exchange (ETDEWEB)

Robbe, P

2002-04-01

The BABAR experiment at SLAC (Stanford linear acceleration center) has been studying since 1999 B meson decays from e{sup +}e{sup -} collisions at the {gamma}(4S) resonance. The first goal of the collaboration was to measure the sin (2{beta}) CP-violation parameter within the standard model. This measurement requires to know with precision the absolute length scale of the detector. A method to test this scale was developed using nuclear interactions in the beam-pipe material. The longitudinal length scale was then determined at the 1 % level precision. The systematic error associated with length measurement in the detector concerning B meson lifetime and B meson oscillation frequency is then negligible with respect to the other errors. The K meson content of B decays is a key ingredient of the sin (2{beta}) measurement and is used to tag the flavour of the other B in events containing a B decaying to a CP eigenstate. The K charge is correlated to the B flavour. Wrong sign kaons, which can dilute B tagging, can come from wrong sign D decays (B{yields} DX). Doubly charmed decays (B{yields} D{sup (*)}D-bar{sup (*)}) K are one possibility to produce wrong sign D decays. The twenty-two decay modes are reconstructed exclusively. The total branching fraction is measured with enough precision to establish that B{yields} D{sup (*)}D-bar{sup (*)} K decays are not the only source of wrong sign D mesons in B decays. (author)

Forecasting disk resource requirements for a Usenet server

International Nuclear Information System (INIS)

Swartz, K.L.

1993-09-01

Three Years ago the Stanford Linear Accelerator Center (SLAC) decided to embrace netnews as a site-wide, multi-platform communications tool for the laboratory's diverse user community. The Usenet newsgroups as well as other world-wide newsgroup hierarchies were appealing for their unique ability to tap a broad pool of information, while the availability of the software on a number of platforms provided a way to communicate to and amongst the computing community. The previous way of doing this ran only on the VM mainframe system and had become increasingly ineffective as users migrated to other platforms. The increasing dependence on netnews brought with it the requirement that the service be reliable. This was dramatically demonstrated when the long-neglected netnews service collapsed under the load of the traditional fall surge in Usenet traffic and the site was without news service for a week while an upgraded system was installed. One result of that painful event was that efforts were made to forecast growth and the accompanying hardware requirements so that equipment could be acquired and installed before problems became visible to the users. This paper describes the major on-disk databases associated with news software, then presents an analysis of the storage requirements for these databases based on data collected at SLAC. A model is developed from this data which permits forecasting of disk resource requirements for a full feed as a function of time and local policies. Suggestions are also made as to how to modify this model for sites which do not carry a full feed

Regulatory inspection of nuclear facilities and enforcement by the regulatory body. Safety guide

International Nuclear Information System (INIS)

2002-01-01

The purpose of this Safety Guide is to provide recommendations for regulatory bodies on the inspection of nuclear facilities, regulatory enforcement and related matters. The objective is to provide the regulatory body with a high level of confidence that operators have the processes in place to ensure compliance and that they do comply with legal requirements, including meeting the safety objectives and requirements of the regulatory body. However, in the event of non-compliance, the regulatory body should take appropriate enforcement action. This Safety Guide covers regulatory inspection and enforcement in relation to nuclear facilities such as: enrichment and fuel manufacturing plants; nuclear power plants; other reactors such as research reactors and critical assemblies; spent fuel reprocessing plants; and facilities for radioactive waste management, such as treatment, storage and disposal facilities. This Safety Guide also covers issues relating to the decommissioning of nuclear facilities, the closure of waste disposal facilities and site rehabilitation. Section 2 sets out the objectives of regulatory inspection and enforcement. Section 3 covers the management of regulatory inspections. Section 4 covers the performance of regulatory inspections, including internal guidance, planning and preparation, methods of inspection and reports of inspections. Section 5 deals with regulatory enforcement actions. Section 6 covers the assessment of regulatory inspections and enforcement activities. The Appendix provides further details on inspection areas for nuclear facilities

Annual Site Environmental Report: 2010 (ASER)

Energy Technology Data Exchange (ETDEWEB)

Sabba, D.

2011-11-11

This report provides information about environmental programs during the calendar year of 2010 at the SLAC National Accelerator Laboratory (SLAC), Menlo Park, California. Activities that overlap the calendar year - i.e., stormwater monitoring covering the winter season of 2010/2011 (October 2010 through May 2011) are also included. SLAC is a federally-funded research and development center with Stanford University as the M&O contractor. Under Executive Order (EO) 13423, Strengthening Federal Environmental, Energy, and Transportation Management, EO 13514, Federal Leadership in Environmental, Energy, and Economic Performance, and DOE Order 450.1A, Environmental Protection Program, SLAC effectively implements and integrates the key elements of an Environmental Management System (EMS) to achieve the site's integrated safety and environmental management system goals. For normal daily activities, SLAC managers and supervisors are responsible for ensuring that policies and procedures are understood and followed so that: (1) Worker safety and health are protected; (2) The environment is protected; and (3) Compliance is ensured. Throughout 2010, SLAC continued to improve its management systems. These systems provided a structured framework for SLAC to implement 'greening of the government' initiatives such as EO 13423, EO 13514, and DOE Orders 450.1A and 430.2B. Overall, management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. During 2010, there were no reportable releases to the environment from SLAC operations. In addition, many improvements in waste minimization, recycling, stormwater management, groundwater restoration, and SLAC's chemical management system (CMS) were continued. The following are among SLAC's environmental accomplishments for 2010. To facilitate management and identification of future potential greenhouse gases (GHG) reduction opportunities, SLAC voluntarily

Annual Site Environmental Report: 2010 (ASER)

International Nuclear Information System (INIS)

Sabba, D.

2011-01-01

This report provides information about environmental programs during the calendar year of 2010 at the SLAC National Accelerator Laboratory (SLAC), Menlo Park, California. Activities that overlap the calendar year - i.e., stormwater monitoring covering the winter season of 2010/2011 (October 2010 through May 2011) are also included. SLAC is a federally-funded research and development center with Stanford University as the M and O contractor. Under Executive Order (EO) 13423, Strengthening Federal Environmental, Energy, and Transportation Management, EO 13514, Federal Leadership in Environmental, Energy, and Economic Performance, and DOE Order 450.1A, Environmental Protection Program, SLAC effectively implements and integrates the key elements of an Environmental Management System (EMS) to achieve the site's integrated safety and environmental management system goals. For normal daily activities, SLAC managers and supervisors are responsible for ensuring that policies and procedures are understood and followed so that: (1) Worker safety and health are protected; (2) The environment is protected; and (3) Compliance is ensured. Throughout 2010, SLAC continued to improve its management systems. These systems provided a structured framework for SLAC to implement 'greening of the government' initiatives such as EO 13423, EO 13514, and DOE Orders 450.1A and 430.2B. Overall, management systems at SLAC are effective, supporting compliance with all relevant statutory and regulatory requirements. During 2010, there were no reportable releases to the environment from SLAC operations. In addition, many improvements in waste minimization, recycling, stormwater management, groundwater restoration, and SLAC's chemical management system (CMS) were continued. The following are among SLAC's environmental accomplishments for 2010. To facilitate management and identification of future potential greenhouse gases (GHG) reduction opportunities, SLAC voluntarily completed GHG inventories

Nuclear Energy Research Initiative. Risk Informed Assessment of Regulatory and Design Requirements for Future Nuclear Power Plants. Annual Report

International Nuclear Information System (INIS)

Ritterbusch, S.E.

2000-01-01

The overall goal of this research project is to support innovation in new nuclear power plant designs. This project is examining the implications, for future reactors and future safety regulation, of utilizing a new risk-informed regulatory system as a replacement for the current system. This innovation will be made possible through development of a scientific, highly risk-informed approach for the design and regulation of nuclear power plants. This approach will include the development and.lor confirmation of corresponding regulatory requirements and industry standards. The major impediment to long term competitiveness of new nuclear plants in the U.S. is the capital cost component--which may need to be reduced on the order of 35% to 40% for Advanced Light Water Reactors (ALWRs) such as System 80+ and Advanced Boiling Water Reactor (ABWR). The required cost reduction for an ALWR such as AP600 or AP1000 would be expected to be less. Such reductions in capital cost will require a fundamental reevaluation of the industry standards and regulatory bases under which nuclear plants are designed and licensed. Fortunately, there is now an increasing awareness that many of the existing regulatory requirements and industry standards are not significantly contributing to safety and reliability and, therefore, are unnecessarily adding to nuclear plant costs. Not only does this degrade the economic competitiveness of nuclear energy, it results in unnecessary costs to the American electricity consumer. While addressing these concerns, this research project will be coordinated with current efforts of industry and NRC to develop risk-informed, performance-based regulations that affect the operation of the existing nuclear plants; however, this project will go farther by focusing on the design of new plants

Nuclear Energy Research Initiative. Risk Informed Assessment of Regulatory and Design Requirements for Future Nuclear Power Plants. Annual Report

Energy Technology Data Exchange (ETDEWEB)

Ritterbusch, S.E.

2000-08-01

The overall goal of this research project is to support innovation in new nuclear power plant designs. This project is examining the implications, for future reactors and future safety regulation, of utilizing a new risk-informed regulatory system as a replacement for the current system. This innovation will be made possible through development of a scientific, highly risk-informed approach for the design and regulation of nuclear power plants. This approach will include the development and.lor confirmation of corresponding regulatory requirements and industry standards. The major impediment to long term competitiveness of new nuclear plants in the U.S. is the capital cost component--which may need to be reduced on the order of 35% to 40% for Advanced Light Water Reactors (ALWRs) such as System 80+ and Advanced Boiling Water Reactor (ABWR). The required cost reduction for an ALWR such as AP600 or AP1000 would be expected to be less. Such reductions in capital cost will require a fundamental reevaluation of the industry standards and regulatory bases under which nuclear plants are designed and licensed. Fortunately, there is now an increasing awareness that many of the existing regulatory requirements and industry standards are not significantly contributing to safety and reliability and, therefore, are unnecessarily adding to nuclear plant costs. Not only does this degrade the economic competitiveness of nuclear energy, it results in unnecessary costs to the American electricity consumer. While addressing these concerns, this research project will be coordinated with current efforts of industry and NRC to develop risk-informed, performance-based regulations that affect the operation of the existing nuclear plants; however, this project will go farther by focusing on the design of new plants.

Oil spill emergency response: Fulfilling regulatory requirements on the Grand Banks

International Nuclear Information System (INIS)

Horvath, C.L.

1991-01-01

Offshore well licensing under Canadian regulations requires the operator to conduct a practice exercise of oil spill countermeasures and emergency response procedures at least yearly, once the drilling program starts. The relevant parts of the Newfoundland Offshore Petroleum Drilling Regulations are summarized and the objectives and benefits of the practice exercises are reviewed. In addition to ensuring regulatory compliance, the exercises also provide the opportunity to test operational procedures, to provide in-house training, and improve response efficiency by regular repetition of the exercise. Exercises in communications during a spill incident in the offshore and in deployment of offshore spill response equipment conducted by Petro-Canada in Newfoundland are described. Problems identified during the exercises are noted

Environment, safety, and health regulatory implementation plan

International Nuclear Information System (INIS)

1993-01-01

To identify, document, and maintain the Uranium Mill Tailings Remedial Action (UMTRA) Project's environment, safety, and health (ES ampersand H) regulatory requirements, the US Department of Energy (DOE) UMTRA Project Office tasked the Technical Assistance Contractor (TAC) to develop a regulatory operating envelope for the UMTRA Project. The system selected for managing the UMTRA regulatory operating envelope data bass is based on the Integrated Project Control/Regulatory Compliance System (IPC/RCS) developed by WASTREN, Inc. (WASTREN, 1993). The IPC/RCS is a tool used for identifying regulatory and institutional requirements and indexing them to hardware, personnel, and program systems on a project. The IPC/RCS will be customized for the UMTRA Project surface remedial action and groundwater restoration programs. The purpose of this plan is to establish the process for implementing and maintaining the UMTRA Project's regulatory operating envelope, which involves identifying all applicable regulatory and institutional requirements and determining compliance status. The plan describes how the Project will identify ES ampersand H regulatory requirements, analyze applicability to the UMTRA Project, and evaluate UMTRA Project compliance status

Data Quality Objectives for Regulatory Requirements for Dangerous Waste Sampling and Analysis; FINAL

International Nuclear Information System (INIS)

MULKEY, C.H.

1999-01-01

This document describes sampling and analytical requirements needed to meet state and federal regulations for dangerous waste (DW). The River Protection Project (RPP) is assigned to the task of storage and interim treatment of hazardous waste. Any final treatment or disposal operations, as well as requirements under the land disposal restrictions (LDRs), fall in the jurisdiction of another Hanford organization and are not part of this scope. The requirements for this Data Quality Objective (DQO) Process were developed using the RPP Data Quality Objective Procedure (Banning 1996), which is based on the U.S. Environmental Protection Agency's (EPA) Guidance for the Data Quality Objectives Process (EPA 1994). Hereafter, this document is referred to as the DW DQO. Federal and state laws and regulations pertaining to waste contain requirements that are dependent upon the composition of the waste stream. These regulatory drivers require that pertinent information be obtained. For many requirements, documented process knowledge of a waste composition can be used instead of analytical data to characterize or designate a waste. When process knowledge alone is used to characterize a waste, it is a best management practice to validate the information with analytical measurements

Radiological and administrative criteria and procedures required by the Radiation Protection Ordinance for exemption from regulatory control

International Nuclear Information System (INIS)

Birkholz, W.

2000-01-01

The system of required radioactivity measurements and limits as well as methods, based on the 10 μSv concept, constitutes the regulatory regime for exemption of radioactive waste materials from regulatory control according to atomic energy law. The methods and administrative procedures are suitable both for smaller amounts of materials, such as those resulting from the use of radioactive substances in scientific research and medical applications, and for the large waste volumes emanating from the dismantling of nuclear installations. The system provided for in the Radiation Protection Ordinance ensures harmonized administrative action of all public authorities involved. (orig./CB) [de

Single-bunch beam loading on the SLAC two-mile accelerator

International Nuclear Information System (INIS)

Koontz, R.F.

1976-01-01

The experiments described were initially prompted by interest in the radiation loss of relativistic electron rings passing through periodic structures. Later, the same experiments became relevant to the theory of energy loss of electrons in large storage rings. In both of these cases, energy loss to the higher order modes of the respective structures could seriously limit their effective operation as acceleration devices. In these experiments, single bunches of electrons with intensities up to 7 x 10 8 electrons per bunch are accelerated through the SLAC three-kilometer accelerator, and their energy spectra are analyzed. Early experiments over a wide energy range (900 MeV to 19 GeV) demonstrated that the energy loss was proportional to the total charge in the bunch but was independent of beam energy. The average energy loss of a single bunch normalized to 10 9 electrons was initially measured to be 38 MeV. The experiments, including much of the equipment development, are described and are compared with theoretical predictions made to date

STATUS OF X-BAND STANDING WAVE STRUCTURE STUDIES AT SLAC

International Nuclear Information System (INIS)

Dolgashev, Valery A.

2003-01-01

The linacs proposed for the Next Linear Collider (NLC) and Japanese Linear Collider (JLC) would contain several thousand X-Band accelerator structures that would operate at a loaded gradient of 50 MV/m. An extensive experimental and theoretical program is underway at SLAC, FNAL and KEK to develop structures that reliably operate at this gradient. The development of standing wave structures is a part of this program. The properties of standing wave structures allow them to operate at the loaded gradient in contrast to traveling wave structures that need conditioning to the unloaded gradient (65 MV/m for NLC/JLC). The gradients in the standing structures tested thus far have been limited by input coupler breakdowns. The behavior of these breakdowns is consistent with a model of pulsed heating due to high magnetic fields. New input couplers have been designed to reduce maximum magnetic fields. This paper discusses design considerations related to high power performance, wakefield suppression and results of high power tests of prototype standing wave structures

Performance of the PEP-II B-Factory Collider at SLAC

International Nuclear Information System (INIS)

Seeman, J.; Browne, M.; Cai, Y.; Colocho, W.; Decker, F.J.; Donald, M.H.; Ecklund, S.; Erickson, R.A.; Fisher, A.S.; Fox, J.D.; Heifets, S.A.; Iverson, R.H.; Kulikov, A.; Li, N.; Novokhatski, A.; Ross, M.C.; Schuh, P.; Smith, T.J.; Sonnad, K.G.; Stanek, M.; Sullivan, M.K.

2006-01-01

PEP-II is an e + e - asymmetric B-Factory Collider located at SLAC operating at the Upsilon 4S resonance (3.1 GeV x 9 GeV). It has reached a luminosity of 9.21 x 10 33 /cm 2 /s and has delivered an integrated luminosity of 710 pb -1 in one day. PEP-II has delivered, over the past six years, an integrated luminosity to the BaBar detector of over 262 fb -1 . PEP-II operates in continuous injection mode for both beams boosting the integrated luminosity. The peak positron current has reached 2.45 A in 1588 bunches. Steady progress is being made in reaching higher luminosity. The goal over the next several years is to reach a luminosity of 2.1 x 10 34 /cm 2 /s. The accelerator physics issues being addressed in PEP-II to reach this goal include the electron cloud instability, beam-beam effects, parasitic beam-beam effects, high RF beam loading, shorter bunches, lower β* y interaction region operation, and coupling control. Figure 1 shows the PEP-II tunnel

An overview of exhaust emissions regulatory requirements and control technology for stationary natural gas engines

International Nuclear Information System (INIS)

Ballard, H.N.; Hay, S.C.; Shade, W.N. Jr.

1992-01-01

In this paper a practical overview of stationary natural gas engine exhaust emissions control technology and trends in emissions regulatory requirements is presented. Selective and non-selective catalytic reduction and lean burn technologies are compared. Particular emphasis is focussed on implications of the Clean Air Act of 1990. Recent emissions reduction conversion kit developments and a practical approach to continuous monitoring are discussed

A comparison of immunotoxic effects of nanomedicinal products with regulatory immunotoxicity testing requirements

Directory of Open Access Journals (Sweden)

Giannakou C

2016-06-01

Full Text Available Christina Giannakou,1,2 Margriet VDZ Park,1 Wim H de Jong,1 Henk van Loveren,1,2 Rob J Vandebriel,1 Robert E Geertsma1 1Centre for Health Protection, National Institute for Public Health and the Environment (RIVM, Bilthoven, 2Department of Toxicogenomics, Maastricht University, Maastricht, the Netherlands Abstract: Nanomaterials (NMs are attractive for biomedical and pharmaceutical applications because of their unique physicochemical and biological properties. A major application area of NMs is drug delivery. Many nanomedicinal products (NMPs currently on the market or in clinical trials are most often based on liposomal products or polymer conjugates. NMPs can be designed to target specific tissues, eg, tumors. In virtually all cases, NMPs will eventually reach the immune system. It has been shown that most NMs end up in organs of the mononuclear phagocytic system, notably liver and spleen. Adverse immune effects, including allergy, hypersensitivity, and immunosuppression, have been reported after NMP administration. Interactions of NMPs with the immune system may therefore constitute important side effects. Currently, no regulatory documents are specifically dedicated to evaluate the immunotoxicity of NMs or NMPs. Their immunotoxicity assessment is performed based on existing guidelines for conventional substances or medicinal products. Due to the unique properties of NMPs when compared with conventional medicinal products, it is uncertain whether the currently prescribed set of tests provides sufficient information for an adequate evaluation of potential immunotoxicity of NMPs. The aim of this study was therefore, to compare the current regulatory immunotoxicity testing requirements with the accumulating knowledge on immunotoxic effects of NMPs in order to identify potential gaps in the safety assessment. This comparison showed that immunotoxic effects, such as complement activation-related pseudoallergy, myelosuppression, inflammasome

Highlights of the SLD Physics Program at the SLAC Linear Collider

Energy Technology Data Exchange (ETDEWEB)

Willocq, Stephane

2001-09-07

Starting in 1989, and continuing through the 1990s, high-energy physics witnessed a flowering of precision measurements in general and tests of the standard model in particular, led by e{sup +}e{sup -} collider experiments operating at the Z{sup 0} resonance. Key contributions to this work came from the SLD collaboration at the SLAC Linear Collider. By exploiting the unique capabilities of this pioneering accelerator and the SLD detector, including a polarized electron beam, exceptionally small beam dimensions, and a CCD pixel vertex detector, SLD produced a broad array of electroweak, heavy-flavor, and QCD measurements. Many of these results are one of a kind or represent the world's standard in precision. This article reviews the highlights of the SLD physics program, with an eye toward associated advances in experimental technique, and the contribution of these measurements to our dramatically improved present understanding of the standard model and its possible extensions.

77 FR 8082 - Regulatory Flexibility Agenda

Science.gov (United States)

2012-02-13

... Required: Yes. Agency Contact: Alicia Goldin, Division of Trading and Markets, Securities and Exchange.../01/11 Regulatory Flexibility Analysis Required: Yes. Agency Contact: Alicia Goldin, Division of... Withdrawn 10/01/11 Regulatory Flexibility Analysis Required: Yes. Agency Contact: Alicia Goldin, Division of...

Regulatory guidance document

International Nuclear Information System (INIS)

1994-05-01

The Office of Civilian Radioactive Waste Management (OCRWM) Program Management System Manual requires preparation of the OCRWM Regulatory Guidance Document (RGD) that addresses licensing, environmental compliance, and safety and health compliance. The document provides: regulatory compliance policy; guidance to OCRWM organizational elements to ensure a consistent approach when complying with regulatory requirements; strategies to achieve policy objectives; organizational responsibilities for regulatory compliance; guidance with regard to Program compliance oversight; and guidance on the contents of a project-level Regulatory Compliance Plan. The scope of the RGD includes site suitability evaluation, licensing, environmental compliance, and safety and health compliance, in accordance with the direction provided by Section 4.6.3 of the PMS Manual. Site suitability evaluation and regulatory compliance during site characterization are significant activities, particularly with regard to the YW MSA. OCRWM's evaluation of whether the Yucca Mountain site is suitable for repository development must precede its submittal of a license application to the Nuclear Regulatory Commission (NRC). Accordingly, site suitability evaluation is discussed in Chapter 4, and the general statements of policy regarding site suitability evaluation are discussed in Section 2.1. Although much of the data and analyses may initially be similar, the licensing process is discussed separately in Chapter 5. Environmental compliance is discussed in Chapter 6. Safety and Health compliance is discussed in Chapter 7

Essay: Bob Siemann-SLC Days at SLAC

International Nuclear Information System (INIS)

Raubenheimer, Tor O.

2008-01-01

program, I suggested an extensive upgrade that also replaced the dipoles with combined function magnets which might have reduced the horizontal emittance another factor of 3. Although he was extremely busy, Bob helped me develop the proposal and understand the magnetic limitations as well as the potential impacts on the beam dynamics. He helped me consider issues well beyond my initial scope. While the proposal never went anywhere and I think Bob had been aware that there was no funding to pursue the option, he saw that it would be a great learning experience for me and it was. In the early 1990's I had simulated a new regime for the beam-ion instability and, with Frank Zimmermann, I developed a model for the effect which was predicted to occur within the high current, low emittance bunch trains in future storage rings or linear colliders. I thought this was pretty good work but Bob convinced me that the next step had to be confirming the theory with measurements. Because the growth rate was inversely dependent on beam sizes and proportional to the vacuum pressure, measurements required significantly increasing the vacuum pressure in existing facilities. Most people discounted trying such an experiment, but with Bob's urging and suggestions and John Byrd's excitement, we managed to make the measurements at the Advanced Light Source (ALS) at Berkeley. By the mid-1990's Bob was completely focused on advanced acceleration concepts and I was not interacting with him as often. At the time, SLAC was putting together a large effort in designing and documenting a design for the Next Linear Collider (NLC) while constructing the NLC Test Accelerator. Bob was worried that a straightforward extrapolation of the microwave technology would be difficult to bring to fruition because of the cost. He wanted to focus on more cost-effective approaches that could enable future accelerators for high energy physics. As usual, he was correct. The experimental programs that he started in direct

Progress report on the SLAC Linear Collider

International Nuclear Information System (INIS)

Kozanecki, W.

1987-11-01

In this paper we report on the status of the SLAC Linear Collider (SLC), the prototype of a new generation of colliding beam accelerators. This novel type of machine holds the potential of extending electron-positron colliding beam studies to center-of-mass (c.m.) energies far in excess of what is economically achievable with colliding beam storage rings. If the technical challenges posed by linear colliders are solvable at a reasonable cost, this new approach would provide an attractive alternative to electron-positron rings, where, because of rapidly rising synchrotron radiation losses, the cost and size of the ring increases with the square of the c.m. energy. In addition to its role as a test vehicle for the linear collider principle, the SLC aims at providing an abundant source of Z 0 decays to high energy physics experiments. Accordingly, two major detectors, the upgraded Mark II, now installed on the SLC beam line, and the state-of-the-art SLD, currently under construction, are preparing to probe the Standard Model at the Z 0 pole. The SLC project was originally funded in 1983. Since the completion of construction, we have been commissioning the machine to bring it up to a performance level adequate for starting the high energy physics program. In the remainder of this paper, we will discuss the status, problems and performance of the major subsystems of the SLC. We will conclude with a brief outline of the physics program, and of the planned enhancements to the capabilities of the machine. 26 refs., 7 figs

Improving nuclear regulatory effectiveness

International Nuclear Information System (INIS)

2001-01-01

Ensuring that nuclear installations are operated and maintained in such a way that their impact on public health and safety is as low as reasonably practicable has been and will continue to be the cornerstone of nuclear regulation. In the past, nuclear incidents provided the main impetus for regulatory change. Today, economic factors, deregulation, technological advancements, government oversight and the general requirements for openness and accountability are leading regulatory bodies to review their effectiveness. In addition, seeking to enhance the present level of nuclear safety by continuously improving the effectiveness of regulatory bodies is seen as one of the ways to strengthen public confidence in the regulatory systems. This report covers the basic concepts underlying nuclear regulatory effectiveness, advances being made and future requirements. The intended audience is primarily nuclear safety regulators, but government authorities, nuclear power plant operators and the general public may also be interested. (author)

The dynein regulatory complex is required for ciliary motility and otolith biogenesis in the inner ear.

Science.gov (United States)

Colantonio, Jessica R; Vermot, Julien; Wu, David; Langenbacher, Adam D; Fraser, Scott; Chen, Jau-Nian; Hill, Kent L

2009-01-08

In teleosts, proper balance and hearing depend on mechanical sensors in the inner ear. These sensors include actin-based microvilli and microtubule-based cilia that extend from the surface of sensory hair cells and attach to biomineralized 'ear stones' (or otoliths). Otolith number, size and placement are under strict developmental control, but the mechanisms that ensure otolith assembly atop specific cells of the sensory epithelium are unclear. Here we demonstrate that cilia motility is required for normal otolith assembly and localization. Using in vivo video microscopy, we show that motile tether cilia at opposite poles of the otic vesicle create fluid vortices that attract otolith precursor particles, thereby biasing an otherwise random distribution to direct localized otolith seeding on tether cilia. Independent knockdown of subunits for the dynein regulatory complex and outer-arm dynein disrupt cilia motility, leading to defective otolith biogenesis. These results demonstrate a requirement for the dynein regulatory complex in vertebrates and show that cilia-driven flow is a key epigenetic factor in controlling otolith biomineralization.

Introduction to the Unified Agenda of Federal Regulatory and Deregulatory Actions

Science.gov (United States)

2010-04-26

... Regulatory Commission Federal Housing Finance Agency Federal Maritime Commission Federal Mediation and... that the Regulatory Flexibility Act may require a Regulatory Flexibility Analysis, actions selected for.... Regulatory Flexibility Analysis Required -- whether an analysis is required by the Regulatory Flexibility Act...

A regulatory adjustment process for the determination of the optimal percentage requirement in an electricity market with Tradable Green Certificates

International Nuclear Information System (INIS)

Currier, Kevin M.

2013-01-01

A system of Tradable Green Certificates (TGCs) is a market-based subsidy scheme designed to promote electricity generation from renewable energy sources such as wind power. Under a TGC system, the principal policy instrument is the “percentage requirement,” which stipulates the percentage of total electricity production (“green” plus “black”) that must be obtained from renewable sources. In this paper, we propose a regulatory adjustment process that a regulator can employ to determine the socially optimal percentage requirement, explicitly accounting for environmental damages resulting from black electricity generation. - Highlights: • A Tradable Green Certificate (TGC) system promotes energy production from renewable sources. • We consider an electricity oligopoly operated under a TGC system. • Welfare analysis must account for damages from “black” electricity production. • We characterize the welfare maximizing (optimal) “percentage requirement.” • We present a regulatory adjustment process that computes the optimal percentage requirement iteratively

UK regulatory standards - the 'Guidance on requirements for authorisation'

International Nuclear Information System (INIS)

Williams, C.R.

1999-01-01

In the United Kingdom, disposal of radioactive waste requires an authorisation under the Radioactive Substances Act 1993. The power to grant such authorisations rests with the Environment Agency for disposals in England and Wales, and with similar Agencies in Scotland and Northern Ireland - namely the Scottish Environment Protection Agency (SEPA) and the Environment and Heritage Service (EHS) of the Department of the Environment for Northern Ireland. In 1997, following two rounds of consultation, the Environment Agency jointly with SEPA and EHS published a document 'Disposal Facilities on Land for Low and Intermediate Level Radioactive Wastes: Guidance on Requirements for Authorisation' - the GRA document. The GRA document outlines the regulatory framework governing the disposal of radioactive waste, general guidance on procedures, the principles and criteria against which proposals for a disposal facility will be assessed, and the radiological and technical requirements which a facility will be expected to meet. In particular, the document states that, in the period after control is withdrawn, the assessed radiological risk from a facility to a representative member of the potentially exposed group at greatest risk should be consistent with a risk target of 10 -6 per year. The document also specifies the information which a developer will need to provide, to demonstrate that a proposal is consistent with the principles and requirements, and identifies other, non-risk-based, criteria. In March 1997, the Secretary of State for the Environment rejected a planning appeal by United Kingdom Nirex Ltd for an underground Rock Characterisation Facility located near Sellafield in Cumbria. That decision has effectively delayed the construction of any deep repository in the UK. Subsequently a House of Lords Select Committee has commenced a major review of nuclear waste management. The Environment Agency continues to be responsible for the authorisation of the shallow

Economics of the specification 6M safety re-evaluation and regulatory requirements

International Nuclear Information System (INIS)

Hopper, C.M.

1985-01-01

The objective of this work was to examine the potential economic impact of the DOT Specification 6M criticality safety re-evaluation and regulatory requirements. The examination was based upon comparative analyses of current authorized fissile material load limits for the 6M, current Federal regulations (and interpretations) limiting the contents of Type B fissile material packages, limiting aggregates of fissile material packages, and recent proposed fissile material mass limits derived from specialized criticality safety analyses of the 6M package. The work examines influences on cost in transportation, handling, and storage of fissile materials. Depending upon facility throughput requirements (and assumed incremental costs of fissile material packaging, storage, and transport), operating, facility storage capacity, and transportation costs can be reduced significantly. As an example of the pricing algorithm application based upon reasonable cost influences, the magnitude of the first year cost reductions could extend beyond four times the cost of the packaging nuclear criticality safety re-evaluation. 1 tab

Regulatory framework for nuclear power plant operation

International Nuclear Information System (INIS)

Perez Alcaniz, T.; Esteban Barriendos, M.

1995-01-01

As the framework of standards and requirements covering each phase of nuclear power plant project and operation developed, plant owners defined their licensing commitments (codes, rules and design requirements) during the project and construction phase before start-up and incorporated regulatory requirements imposed by the regulatory Body during the licensing process prior to operation. This produces a regulatory framework for operating a plant. It includes the Licensing Basis, which is the starting point for analyzing and incorporating new requirements, and for re-evaluation of existing ones. This presentation focuses on the problems of applying this regulatory framework to new operating activities, in particular to new projects, analyzing new requirements, and reconsidering existing ones. Clearly establishing a plant's licensing basis allows all organizations involved in plant operation to apply the requirements in a more rational way. (Author)

Requirements for growth and IL-10 expression of highly purified human T regulatory cells

OpenAIRE

Bonacci, Benedetta; Edwards, Brandon; Jia, Shuang; Williams, Calvin; Hessner, Martin J.; Gauld, Stephen; Verbsky, James

2012-01-01

Human regulatory T cells (TR) cells have potential for the treatment of a variety of immune mediated diseases but the anergic phenotype of these cells makes them difficult to expand in vitro. We have examined the requirements for growth and cytokine expression from highly purified human TR cells, and correlated these findings with the signal transduction events of these cells. We demonstrate that these cells do not proliferate or secrete IL-10 even in the presence of high doses of IL-2. Stimu...

Lessons learned from the Fukushima Dai-ichi accident and responses in NRA regulatory requirements

International Nuclear Information System (INIS)

Fuketa, Toyoshi

2014-01-01

The author would like to present significant lessons learned from the TEPCO’s Fukushima Dai-ichi accident and responses in regulatory requirements developed by the Nuclear Regulation Authority for power-producing light water reactors. The presentation will cover prevention of structures, systems and components failures, measures to prevent common cause failures, prevention of core damage, mitigation of severe accidents, emergency preparedness, continuous improvement of safety, use of probabilistic risk assessment, and post-accident regulation on the Fukushima Dai-ichi. (author)

Improvements in emittance wake field optimization for the SLAC Linear Collider

CERN Document Server

Decker, Franz Josef

2003-01-01

The transverse emittances in the SLAC Linear Collider can be severely diluted by collective wakefield effects and dispersion. For the 1997/98 SLC/SLD run important changes were implemented in the way the emittance is optimized. Early in the linac, where the energy spread is large due to BNS damping, the emittance growth is dominated by dispersion. In this regime emittance tuning bumps may introduce additional wakefield tails and their use is now avoided. At the end of the linac the energy spread is minimal and the emittance measurement is most sensitive to wakefield emittance dilution. In previous years, the emittances were tuned on wire scanners located near but not at the end of the linac (after about 90% of its length). Simulations show that emittance growth of up to 100% can occur in the remaining 10%. In this run wire scanners at the entrance of the Final Focus, the last place where the emittances can be measured, were used for the optimization. Screens at the end of the linac allow additional real time ...

[Regulatory requirements regarding cell-based medicinal products for human and veterinary use - a comparison].

Science.gov (United States)

Kuhlmann-Gottke, Johanna; Duchow, Karin

2015-11-01

At present, there is no separate regulatory framework for cell-based medicinal products (CBMP) for veterinary use at the European or German level. Current European and national regulations exclusively apply to the corresponding medicinal products for human use. An increasing number of requests for the regulatory classification of CBMP for veterinary use, such as allogeneic stem cell preparations and dendritic cell-based autologous tumour vaccines, and a rise in scientific advice for companies developing these products, illustrate the need for adequate legislation. Currently, advice is given and decisions are made on a case-by-case basis regarding the regulatory classification and authorisation requirements.Since some of the CBMP - in particular in the area of stem-cell products - are developed in parallel for human and veterinary use, there is an urgent need to create specific legal definitions, regulations, and guidelines for these complex innovative products in the veterinary sector as well. Otherwise, there is a risk that that the current legal grey area regarding veterinary medicinal products will impede therapeutic innovations in the long run. A harmonised EU-wide approach is desirable. Currently the European legislation on veterinary medicinal products is under revision. In this context, veterinary therapeutics based on allogeneic cells and tissues will be defined and regulated. Certainly, the legal framework does not have to be as comprehensive as for human CBMP; a leaner solution is conceivable, similar to the special provisions for advanced-therapy medicinal products laid down in the German Medicines Act.

Regulatory aspects of criticality control in Australia

International Nuclear Information System (INIS)

Zimin, Sergei

2003-01-01

With the creation of Australian Radiation Protection and Nuclear Safety Agency (ARPANSA) the Australian approach to criticality safety was revisited. Consistency with international best practices is required by the Act that created ARPANSA and this was applied to practices in criticality safety adopted in other countries. This required extensive regulatory efforts both in auditing the major Australian Nuclear Operator, Australian Nuclear Science and Technology Organisation (ANSTO), and assessing the existing in Australia criticality safety practices and implementing the required changes using the new legislative power of ARPANSA. The adopted regulatory approach is formulated through both the issued by ARPANSA licenses for nuclear installations (including reactors, fuel stores and radioactive waste stores) and the string of new regulatory documents, including the Regulatory Assessment Principles and the Regulatory Assessment Guidelines for criticality safety. The main features of the adopted regulation include the requirements of independent peer-review, ongoing refresher training coupled with annual accreditation and the reliance on the safe design rather than on an administrative control. (author)

Regulatory analysis technical evaluation handbook. Final report

International Nuclear Information System (INIS)

1997-01-01

The purpose of this Handbook is to provide guidance to the regulatory analyst to promote preparation of quality regulatory analysis documents and to implement the policies of the Regulatory Analysis Guidelines of the US Nuclear Regulatory Commission (NUREG/BR-0058 Rev. 2). This Handbook expands upon policy concepts included in the NRC Guidelines and translates the six steps in preparing regulatory analyses into implementable methodologies for the analyst. It provides standardized methods of preparation and presentation of regulatory analyses, with the inclusion of input that will satisfy all backfit requirements and requirements of NRC's Committee to Review Generic Requirements. Information on the objectives of the safety goal evaluation process and potential data sources for preparing a safety goal evaluation is also included. Consistent application of the methods provided here will result in more directly comparable analyses, thus aiding decision-makers in evaluating and comparing various regulatory actions. The handbook is being issued in loose-leaf format to facilitate revisions. NRC intends to periodically revise the handbook as new and improved guidance, data, and methods become available

Evaluation of the applicability of existing nuclear power plant regulatory requirements in the U.S. to advanced small modular reactors.

Energy Technology Data Exchange (ETDEWEB)

LaChance, Jeffrey L.; Wheeler, Timothy A.; Farnum, Cathy Ottinger; Middleton, Bobby D.; Jordan, Sabina Erteza; Duran, Felicia Angelica; Baum, Gregory A.

2013-05-01

The current wave of small modular reactor (SMR) designs all have the goal of reducing the cost of management and operations. By optimizing the system, the goal is to make these power plants safer, cheaper to operate and maintain, and more secure. In particular, the reduction in plant staffing can result in significant cost savings. The introduction of advanced reactor designs and increased use of advanced automation technologies in existing nuclear power plants will likely change the roles, responsibilities, composition, and size of the crews required to control plant operations. Similarly, certain security staffing requirements for traditional operational nuclear power plants may not be appropriate or necessary for SMRs due to the simpler, safer and more automated design characteristics of SMRs. As a first step in a process to identify where regulatory requirements may be met with reduced staffing and therefore lower cost, this report identifies the regulatory requirements and associated guidance utilized in the licensing of existing reactors. The potential applicability of these regulations to advanced SMR designs is identified taking into account the unique features of these types of reactors.

Development of regulatory policy for SMART-P

Energy Technology Data Exchange (ETDEWEB)

Lee, S. H.; Lee, Y. H.; Moo, Philip; Koh, B. J.; Son, M. K.; Han, G. H.; Kim, D. H. [Korea Association for Nuclear Technology, Daejeon (Korea, Republic of)

2004-06-15

KAERI promoted the construction of a research reactor, SMART-P, the reduced scale of SMART, with intent to demonstrate the safety and performance of SMART. According to this progress, the development of regulatory process for SMART-P became necessary. The establishment of regulatory policy, based on the current regulatory guidelines as well as technical aspect, became essential matters. Considering the on-going small and medium size reactors in near future, the selection of the appropriate measure in the existing regulatory process to SMART-P is very important. Thus the schematic study for the applicable licensing procedure and regulatory requirements suitable for SMART-P is required.

Development of regulatory policy for SMART-P

Energy Technology Data Exchange (ETDEWEB)

Lee, S. H.; Moon, S. H.; Lee, Y. H.; Son, M. K.; Han, K. H.; Kim, D. H. [Korea Association for Nuclear Technology, Taejon (Korea, Republic of)

2003-06-15

KAERI promoted the construction of a research reactor, SMART-P, the reduced scale of SMART, with intent to demonstrate the safety and performance of SMART. According to this progress, the development of regulatory process for SMART-P became necessary. The establishment of regulatory policy, based on the current regulatory guidelines as well as technical aspect, became essential matters. Considering the on-going small and medium size reactors m near future, the selection of the appropriate measure in the existing regulatory process to SMART-P is very important. Thus the schematic study for the applicable licensing procedure and regulatory requirements suitable for SMART-P is required.

Regulatory requirements for groundwater monitoring networks at hazardous waste sites

International Nuclear Information System (INIS)

Keller, J.F.

1989-10-01

In the absence of an explicit national mandate to protect groundwater quality, operators of active and inactive hazardous waste sites must use a number of statutes and regulations as guidance for detecting, correcting, and preventing groundwater contamination. The objective of this paper is to provide a framework of the technical and regulatory considerations that are important to the development of groundwater monitoring programs at hazardous waste sites. The technical site-specific needs and regulatory considerations, including existing groundwater standards and classifications, will be presented. 14 refs., 2 tabs

Emittance studies of the BNL/SLAC/UCLA 1.6 cell photocathode rf gun

International Nuclear Information System (INIS)

Palmer, D.T.; Miller, R.H.; Wang, X.J.

1997-01-01

The symmetrized 1.6 cell S-band photocathode gun developed by the BNL/SLAC/UCLA collaboration is in operation at the Brookhaven Accelerator Test Facility (ATF). A novel emittance compensation solenoid magnet has also been designed, built and is in operation at the ATF. These two subsystems form an emittance compensated photoinjector used for beam dynamics, advanced acceleration and free electron laser experiments at the ATF. The highest acceleration field achieved on the copper cathode is 150 MV/m, and the guns normal operating field is 130 MV/m. The maximum rf pulse length is 3 micros. The transverse emittance of the photoelectron beam were measured for various injection parameters. The 1 nC emittance results are presented along with electron bunch length measurements that indicated that at above the 400 pC, space charge bunch lengthening is occurring. The thermal emittance, ε o , of the copper cathode has been measured

78 FR 44275 - Semiannual Regulatory Agenda

Science.gov (United States)

2013-07-23

... Rights. National Park Service--Completed Actions Regulation Sequence No. Title Identifier No. 200 Winter.... Timetable: Action Date FR Cite NPRM 07/00/13 Final Action 05/00/14 Regulatory Flexibility Analysis Required...: Action Date FR Cite NPRM 10/00/14 Final Action 10/00/14 Regulatory Flexibility Analysis Required: Yes...

Regulatory philosophy and requirements for radiation control in Canadian uranium mine-mill facilities

International Nuclear Information System (INIS)

Dory, A.B.

1981-10-01

With the point made that radiation exposure is one of the health hazards of uranium mining and accordingly has to be controlled, the Canadian regulatory philosophy is outlined as it pertains to the uranium mining industry. Two extremes in regulatory approach are examined, and the joint regulatory process is explained. Two examples of poor management performance are given, and the role of mine unions in the regulatory process is touched upon. The development of new regulations to cover ventilation and employee training is sketched briefly. The author concludes with a general expression of objectives for the eighties which include improved personal dosimetry

Safety Committees for Argentinean Research Reactor - Regulatory Issues

International Nuclear Information System (INIS)

Perrin, Carlos D.

2009-01-01

In the field of radiological and nuclear safety, the Nuclear Regulatory Authority (ARN) of Argentina controls three research reactors and three critical assemblies, by means of evaluations, audits and inspections, in order to ensure the fulfillment of the requirements established in the Licenses, in the Regulatory Standards and in the Mandatory Documentation in general. From the Nuclear Regulatory Authority's point of view, within the general process of research reactors safety management, the Operational Organization self verification of radiological and nuclear safety plays an outstanding role. In this aspect the ARN has established specific requirements in the Regulatory Standards, in the Operation Licenses and in the Operational Limits and Conditions. These requirements include the figure of different safety committees, which act as reviewers or advisers in diverse situations. This paper describes the main characteristics of the committees, their function, scope and the regulatory documents where the requirements are included. (author)

Methodology for the Systematic Assessment of the Regulatory Competence Needs (SARCoN) for Regulatory Bodies of Nuclear Installations

International Nuclear Information System (INIS)

2015-03-01

A regulatory body’s competence is dependent, among other things, on the competence of its staff. A necessary, but not sufficient, condition for a regulatory body to be competent is that its staff can perform the tasks related to the functions of the regulatory body. In 2001, the IAEA published TECDOC 1254, Training the Staff of the Regulatory Body for Nuclear Facilities: A Competency Framework, which examines the manner in which the recognized regulatory functions of a nuclear regulatory body results in competence needs. Using the internationally recognized systematic approach to training, TECDOC 1254 provides a framework for regulatory bodies for managing training and developing, and maintaining the competence of its staff. It has been successfully used by many regulatory bodies all over the world, including States embarking on a nuclear power programme. The IAEA has also introduced a methodology and an assessment tool — Guidelines for Systematic Assessment of Regulatory Competence Needs (SARCoN) — which provides practical guidance on analysing the training and development needs of a regulatory body and, through a gap analysis, guidance on establishing competence needs and how to meet them. In 2013, the IAEA published Safety Reports Series No. 79, Managing Regulatory Body Competence, which provides generic guidance based on IAEA safety requirements in the development of a competence management system within a regulatory body’s integrated management system. An appendix in the Safety Report deals with the special case of building up the competence of regulatory bodies as part of the overall process of establishing an embarking State’s regulatory system. This publication provides guidance for the analysis of required and existing competences to identify those required by the regulatory body to perform its functions and therefore associated needs for acquiring competences. Hence, it is equally applicable to the needs of States embarking on nuclear power

Mission Risk Reduction Regulatory Change Management

Science.gov (United States)

Scroggins, Sharon

2007-01-01

NASA Headquarters Environmental Management Division supports NASA's mission to pioneer the future in space exploration, scientific discovery, and aeronautics research by integrating environmental considerations into programs and projects early-on, thereby proactively reducing NASA's exposure to institutional, programmatic and operational risk. As part of this effort, NASA established the Principal Center for Regulatory Risk Analysis and Communication (RRAC PC) as a resource for detecting, analyzing, and communicating environmental regulatory risks to the NASA stakeholder community. The RRAC PC focuses on detecting emerging environmental regulations and other operational change drivers that may pose risks to NASA programs and facilities, and effectively communicating the potential risks. For example, regulatory change may restrict how and where certain activities or operations may be conducted. Regulatory change can also directly affect the ability to use certain materials by mandating a production phase-out or restricting usage applications of certain materials. Regulatory change can result in significant adverse impacts to NASA programs and facilities due to NASA's stringent performance requirements for materials and components related to human-rated space vehicles. Even if a regulation does not directly affect NASA operations, U.S. and international regulations can pose program risks indirectly through requirements levied on manufacturers and vendors of components and materials. For example, manufacturers can change their formulations to comply with new regulatory requirements. Such changes can require time-consuming and costly requalification certification for use in human spaceflight programs. The RRAC PC has implemented a system for proactively managing regulatory change to minimize potential adverse impacts to NASA programs and facilities. This presentation highlights the process utilized by the RRACPC to communicate regulatory change and the associated

High-power rf pulse compression with SLED-II at SLAC

International Nuclear Information System (INIS)

Nantista, C.

1993-04-01

Increasing the peak rf power available from X-band microwave tubes by means of rf pulse compression is envisioned as a way of achieving the few-hundred-megawatt power levels needed to drive a next-generation linear collider with 50--100 MW klystrons. SLED-II is a method of pulse compression similar in principal to the SLED method currently in use on the SLC and the LEP injector linac. It utilizes low-los resonant delay lines in place of the storage cavities of the latter. This produces the added benefit of a flat-topped output pulse. At SLAC, we have designed and constructed a prototype SLED-II pulse-compression system which operates in the circular TE 01 mode. It includes a circular-guide 3-dB coupler and other novel components. Low-power and initial high-power tests have been made, yielding a peak power multiplication of 4.8 at an efficiency of 40%. The system will be used in providing power for structure tests in the ASTA (Accelerator Structures Test Area) bunker. An upgraded second prototype will have improved efficiency and will serve as a model for the pulse compression system of the NLCTA (Next Linear Collider Test Accelerator)

Regulatory issues associated with the Multi-Purpose (MPC) system

International Nuclear Information System (INIS)

Roberts, J.P.; Desell, L.J.; Birch, M.L.; Morgan, R.G.

1994-01-01

The US Department of Energy Office of Civilian Radioactive Waste Management is developing a Multi-Purpose Canister system to promote compatibility between the waste program elements of storage, transportation, and disposal. The development of a Multi-Purpose Canister system requires meeting various regulatory requirements. These regulatory requirements are set forth in environmental and Nuclear Regulatory Commission (NRC) regulations. This paper discusses the more significant regulatory issues that must be addressed in the development of a Multi-Purpose Canister system by the Department of Energy

Study of the doubly-charmed decays of B mesons with the experiment BABAR in SLAC

International Nuclear Information System (INIS)

Robbe, P.

2002-04-01

The BABAR experiment at SLAC (Stanford linear acceleration center) has been studying since 1999 B meson decays from e + e - collisions at the γ(4S) resonance. The first goal of the collaboration was to measure the sin (2β) CP-violation parameter within the standard model. This measurement requires to know with precision the absolute length scale of the detector. A method to test this scale was developed using nuclear interactions in the beam-pipe material. The longitudinal length scale was then determined at the 1 % level precision. The systematic error associated with length measurement in the detector concerning B meson lifetime and B meson oscillation frequency is then negligible with respect to the other errors. The K meson content of B decays is a key ingredient of the sin (2β) measurement and is used to tag the flavour of the other B in events containing a B decaying to a CP eigenstate. The K charge is correlated to the B flavour. Wrong sign kaons, which can dilute B tagging, can come from wrong sign D decays (B→ DX). Doubly charmed decays (B→ D (*) D-bar (*) K are one possibility to produce wrong sign D decays. The twenty-two decay modes are reconstructed exclusively. The total branching fraction is measured with enough precision to establish that B→ D (*) D-bar (*) K decays are not the only source of wrong sign D mesons in B decays. (author)

Design reviews from a regulatory perspective

International Nuclear Information System (INIS)

Foster, B.D.

1991-01-01

This paper presents views on the role of the licensing engineer in the design process with specific emphasis on design reviews and the automated information management tools that support design reviews. The licensing engineer is seen as an important member of a design review team. The initial focus of the licensing engineer during design reviews is shown to be on ensuring that applicable regulatory requirements are addressed by the design. The utility of an automated tool, such as a commitments management system, to support regulatory requirements identification is discussed. The next responsibility of the licensing engineer is seen as verifying that regulatory requirements are transformed into measurable performance requirements. Performance requirements are shown to provide the basis for developing detailed design review criteria. Licensing engineer input during design reviews is discussed. This input is shown to be especially critical in cases where review findings may impact application of regulatory requirements. The use of automated tools in supporting design reviews is discussed. An information structure is proposed to support design reviews in a regulated environment. This information structure is shown to be useful to activities beyond design reviews. Incorporation of the proposed information structure into the Licensing Support System is proposed

Committee Report of the BEPC-II Project Design Review May 13-15, 2002, SLAC

Energy Technology Data Exchange (ETDEWEB)

Kawakami, Traci M.

2002-08-26

As part of the US-China Cooperative Program in High Energy Physics for the year 2002, a BEPC-II Upgrade Review meeting was held at SLAC, May 13-15, 2002. The upgrade is aimed at improving the luminosity and performance of the BEPC facility at IHEP in Beijing, China with major upgrades to the injector linac, storage ring, and detector. This review addresses mainly the accelerator related issues. Prior to the review, an updated Draft Design Report was made available to the review team. Most important technical change since April 2001 has been a change from a single-ring configuration to a doublering. The goal of the review is to determine whether BEPC-II, if built as described, will meet the operations and physics goals. The charge to the review team is attached as Appendix A.

Regulatory requirements for clinical trial and marketing authorisation application for cell-based medicinal products.

Science.gov (United States)

Salmikangas, P; Flory, E; Reinhardt, J; Hinz, T; Maciulaitis, R

2010-01-01

The new era of regenerative medicine has led to rapid development of new innovative therapies especially for diseases and tissue/organ defects for which traditional therapies and medicinal products have not provided satisfactory outcome. Although the clinical use and developments of cell-based medicinal products (CBMPs) could be witnessed already for a decade, robust scientific and regulatory provisions for these products have only recently been enacted. The new Regulation for Advanced Therapies (EC) 1394/2007 together with the revised Annex I, Part IV of Directive 2001/83/EC provides the new legal framework for CBMPs. The wide variety of cell-based products and the foreseen limitations (small sample sizes, short shelf life) vs. particular risks (microbiological purity, variability, immunogenicity, tumourigenicity) associated with CBMPs have called for a flexible, case-by-case regulatory approach for these products. Consequently, a risk-based approach has been developed to allow definition of the amount of scientific data needed for a Marketing Authorisation Application (MAA) of each CBMP. The article provides further insight into the initial risk evaluation, as well as to the quality, non-clinical, and clinical requirements of CBMPs. Special somatic cell therapies designed for active immunotherapy are also addressed.

Guidelines on how to meet the requirement to keep all exposures as low as reasonably achievable. Regulatory guide

International Nuclear Information System (INIS)

1997-01-01

The purpose of Regulatory Guide G-129 (E) is to provide Atomic Energy Control Board (AECB) licensees with guidelines on how to meet the forthcoming AECB regulatory requirement to keep doses received by workers and members of the public As Low As Reasonably Achievable (ALARA), social and economic factors taken into account. it is realized that the scope for realistic dose reductions will vary depending on the nature of the licensed activity. Therefore, criteria are given in section D for determining if doses can be deemed to be as low as reasonably achievable without further evaluation. The elements that the AECB considers to be essential in the approach to ALARA are described in section E and are summarized as follows: a demonstrated management commitment to the ALARA principle; the implementation of ALARA through a licensee's organization and management, provision of resources, training, establishment of action levels, documentation and other measures; and regular operational reviews. The above elements will be the focus of any AECB assessment to verify compliance with the requirement to keep radiation exposures as low as reasonably achievable. (author)

Regulatory science requirements of labeling of genetically modified food.

Science.gov (United States)

Moghissi, A Alan; Jaeger, Lisa M; Shafei, Dania; Bloom, Lindsey L

2018-05-01

This paper provides an overview of the evolution of food labeling in the USA. It briefly describes the three phases of agricultural development consisting of naturally occurring, cross-bred, and genetically engineered, edited or modified crops, otherwise known as Genetically Modified Organisms (GMO). It uses the Best Available Regulatory Science (BARS) and Metrics for Evaluation of Regulatory Science Claims (MERSC) to evaluate the scientific validity of claims applicable to GMO and the Best Available Public Information (BAPI) to evaluate the pronouncements by public media and others. Subsequently claims on health risk, ecological risk, consumer choice, and corporate greed are evaluated based on BARS/MERSC and BAPI. The paper concludes by suggesting that labeling of food containing GMO should consider the consumer's choice, such as the food used by those who desire kosher and halal food. Furthermore, the consumer choice is already met by the exclusion of GMO in organic food.

Regulatory requirements on management of radioactive material safe transport in China

International Nuclear Information System (INIS)

Chu, C.

2016-01-01

Since 1980s, the IAEA Regulation for safe transport of radioactive material was introduced into China; the regulatory system of China began with international standards, and walked towards the institutionalized. In 2003 the National People’s Congress (NPC) promulgated “the Act on the Prevention of Radioactive Pollution of the People's Republic of China”. In 2009 “Regulation for the Safe Transport of Radioactive Material” (Referred to “Regulation”) was promulgated by the State Council. Subsequently, the National Nuclear Safety Administration (NNSA) began to formulate executive detailed department rules, regulations guidelines and standards. The present system of acts, regulations and standards on management of safe transport of radioactive material in China and future planning were introduced in this paper. Meanwhile, the paper described the specific administration requirements of the Regulation on classification management of radioactive materials, license management of transport packaging including design, manufacture and use, licensing management of transport activities and the provisions of illegal behaviors arising in safe transport of radioactive material. (author)

Risk-based Regulatory Evaluation Program methodology

International Nuclear Information System (INIS)

DuCharme, A.R.; Sanders, G.A.; Carlson, D.D.; Asselin, S.V.

1987-01-01

The objectives of this DOE-supported Regulatory Evaluation Progrwam are to analyze and evaluate the safety importance and economic significance of existing regulatory guidance in order to assist in the improvement of the regulatory process for current generation and future design reactors. A risk-based cost-benefit methodology was developed to evaluate the safety benefit and cost of specific regulations or Standard Review Plan sections. Risk-based methods can be used in lieu of or in combination with deterministic methods in developing regulatory requirements and reaching regulatory decisions

Global Regulatory Differences for Gene- and Cell-Based Therapies

DEFF Research Database (Denmark)

Coppens, Delphi G M; De Bruin, Marie L; Leufkens, Hubert G M

2017-01-01

Gene- and cell-based therapies (GCTs) offer potential new treatment options for unmet medical needs. However, the use of conventional regulatory requirements for medicinal products to approve GCTs may impede patient access and therapeutic innovation. Furthermore, requirements differ between...... jurisdictions, complicating the global regulatory landscape. We provide a comparative overview of regulatory requirements for GCT approval in five jurisdictions and hypothesize on the consequences of the observed global differences on patient access and therapeutic innovation....

NRC regulatory agenda

International Nuclear Information System (INIS)

1993-07-01

The NRC Regulatory Agenda is a compilation of all rules on which the NRC has recently completed action, or has proposed action, or is considering action, and all petitions for rulemaking which have been received by the Commission and are pending disposition by the Commission. The Regulatory Agenda is updated and issued each quarter. The rules on which final action has been taken since March 31, 1993 are: Repeal of NRC standards of conduct; Fitness-for-duty requirements for licensees who possess, use, or transport Category I material; Training and qualification of nuclear power plant personnel; Monitoring the effectiveness of maintenance at nuclear power plants; Licensing requirements for land disposal of radioactive wastes; and Licensees' announcements of safeguards inspections

Legislative framework and regulatory requirements for the introduction of nuclear power

International Nuclear Information System (INIS)

Ha-Vinh, Phuong

1975-01-01

The adoption of appropriate legislation is to be considered as a prerequisite to the introduction of nuclear power in view of the issues that need to be regulated. Preparatory steps should be started at the earliest stage in conjunction with the planning of nuclear power projects. The primary objectives of a licensing scheme are to ensure safety, public health and environmental protection as well as financial protection for third parties in case of nuclear incident. For licensing purposes, a legislative framework and regulatory determinations are required. Within such a framework and pursuant to such regulatory determinations, the elaboration of safety standards, rules, guides and enforcement procedures is to be considered of paramount importance. To this end a number of international recommendations and advisory material prepared by the IAEA provide useful guidance. A licensing process would normally be split into several stages relating to site approval, construction permit, pre-operational tests, and operating licence, each stage being subject to safety assessments and reviews as determined by regulations. Financial protection against nuclear damage has also to be insured. A special regime of nuclear liability has been established by international conventions, based on the principle of strict liability of the operator of a nuclear installation. As a result of such channelling of liability to him, his liability is limited in amount and time. This liability system has the dual purpose of ensuring appropriate protection for potential victims and of relieving the nuclear industry from unlimited liability risks, which would impede practical applications of atomic energy. For the elaboration of nuclear legislation and specialized regulations the Agency's advisory services have proved to be of help to countries embarking on a nuclear power programme. (author)

Recent SLAC measurements of the spin dependent structure functions for the proton and neutron

International Nuclear Information System (INIS)

Zapalac, G.

1995-09-01

The authors present results from SLAC experiments E142 and E143 for the spin dependent structure functions of the proton g 1 p (x, Q 2 ) and neutron g 1 n (x,Q 2 ) measured in deep inelastic scattering of polarized electrons from a polarized target. Experiment E142 measures ∫ 0 1 g 1 n (x)dx = -0.022 ± 0.011 at 2 > = 2 (GeV/c) 2 using a polarized 3 He target. Experiment E143 measures ∫ 0 1 g 1 p (x)dx = 0.129 ± 0.011 at 2 > = 3 (GeV/c) 2 using a polarized NH 3 target. These results are combined at Q 2 = 3 (GeV/c) 2 to yield ∫ 0 1 [g 1 p (x) - g 1 n (x)]dx = 0.151 ± 0.015. The Bjorken sum rule predicts 0.171 ± 0.008

Regulatory systems-based licensing guidance documentation

International Nuclear Information System (INIS)

Delligatti, M.S.

1991-01-01

The US Nuclear Regulatory Commission (NRC) has developed a series of licensing guidance documents based on the regulatory requirements in Part 60 of Title 10 of the Code of Federal Regulations (10 CFR Part 60). This regulatory systems-based approach to licensing guidance documentation relies on the definition of the high-level waste repository in 10 CFR Part 60. A document which is important for the frame-work it gives to other programmatic licensing guidance is the Draft Regulatory Guide open-quotes Format and Content for the License Application for the High-Level Waste Repositoryclose quotes (FCRG). The FCRG describes a format and content acceptable to NRC for a high-level waste repository license application pursuant to the requirements of 10 CFR Part 60. Other licensing guidance documents will be compatible with the FCRG

Design optimization and transverse coherence analysis for an x-ray free electron laser driven by SLAC LINAC

International Nuclear Information System (INIS)

Xie, M.

1995-01-01

I present a design study for an X-ray Free Electron Laser driven by the SLAC linac, the Linac Coherent Light Source (LCLS). The study assumes the LCLS is based on Self-Amplified Spontaneous Emission (SASE). Following a brief review of the fundamentals of SASE, I will provide without derivation a collection of formulas relating SASE performance to the system parameters. These formulas allow quick evaluation of FEL designs and provide powerful tools for optimization in multi-dimensional parameter space. Optimization is carried out for the LCLS over all independent system parameters modeled, subjected to a number of practical constraints. In addition to the optimizations concerning gain and power, another important consideration for a single pass FEL starting from noise is the transverse coherence property of the amplified radiation, especially at short wavelength. A widely used emittance criteria for FELs requires that the emittance is smaller than the radiation wavelength divided by 4π. For the LCLS the criteria is violated by a factor of 5, at a normalized emittance of 1.5 mm-mrad, wavelength of 1.5 angstrom, and beam energy of 15 GeV. Thus it is important to check quantitatively the emittance effect on the transverse coherence. I will examine the emittance effect on transverse coherence by analyzing different transverse modes and show that full transverse coherence can be obtained even at the LCLS parameter regime

Quality assurance within regulatory bodies

International Nuclear Information System (INIS)

1999-06-01

The IAEA directed extensive efforts during the years 1991 to 1995 to the integral revision of all NUSS quality assurance publications, which were approved and issued as Safety Series No.50-C/SG-Q, Quality Assurance for Safety in Nuclear Power Plants and other Nuclear Installations (1996). When these quality assurance publications were developed, their prime focus was on requirements against which work performed by the licensees could be measured and assessed by the regulatory bodies. In this way, they only helped to facilitate the functions of regulators. No requirements or recommendations were provided on how the regulators should ensure the effective implementation of their own activities. The present publication is a first attempt to collect, integrate and offer available experience to directly support performance of regulatory activities. It presents a comprehensive compilation on the application of quality assurance principles and methods by regulatory bodies to their activities. The aim is consistent good performance of regulatory activities through a systematic approach

Nuclear Regulatory Commission: more aggressive leadership needed

International Nuclear Information System (INIS)

Staats, E.B.

1980-01-01

The Energy Reorganization Act of 1974 which established the Nuclear Regulatory Commission required GAO to evaluate the Commission's performance by January 18, 1980. This report responds to that requirement. GAO concluded that, although improvements have been made, the Commission's nuclear regulatory performance can be characterized best as slow, indecisive, cautious - in a word, complacent. This has largely resulted from a lack of aggressive leadership as evidenced by the Commissioners' failure to establish regulatory goals, control policymaking, and most importantly, clearly define their roles in nuclear regulation

Evaluation of research reactor fuel reliability in support of regulatory requirements

International Nuclear Information System (INIS)

Sokolov, Eugene N.

2005-01-01

This standards, codes and practices survey is devoted to the problem of reliability of R and D especially research reactor fuel (RRF) performance-related processes. Regulatory R and D evaluations were based on one standard and just few of them provide correlation to other relative standards whereas synthetic process approach reflects actual status of particular R and D practices. Fuel performance regulatory parameters are based on quality standards. A reliability process-based method similar to PSA/FMEA is proposed to evaluate RRF performance- related parameters in terms of reactor safety. (author)

Evaluation of research reactor fuel reliability in support of regulatory requirements

Energy Technology Data Exchange (ETDEWEB)

Sokolov, Eugene N [Chalk River Laboratories, AECL, Chalk River, ON, K0J 1J0 (Canada)

2005-07-01

This standards, codes and practices survey is devoted to the problem of reliability of R and D especially research reactor fuel (RRF) performance-related processes. Regulatory R and D evaluations were based on one standard and just few of them provide correlation to other relative standards whereas synthetic process approach reflects actual status of particular R and D practices. Fuel performance regulatory parameters are based on quality standards. A reliability process-based method similar to PSA/FMEA is proposed to evaluate RRF performance- related parameters in terms of reactor safety. (author)

Development of guidance on applications of regulatory requirements for regulating large, contaminated equipment and large decommissioning and decontamination (D and D) components

International Nuclear Information System (INIS)

Pope, R.B.; Easton, E.P.; Cook, J.R.; Boyle, R.W.

1997-01-01

In 1985, the International Atomic Energy Agency issued revised regulations for the safe transport of radioactive material. Significant were major changes to requirements for Low Specific Activity (LSA) material and Surface Contaminated Objects (SCOs). As these requirements were adopted into regulations in the United States, it was recognised that guidance on how to apply these requirements to large, contaminated/activated pieces of equipment and decommissioning and decontamination (D and D) objects would be needed both by the regulators and those regulated to clarify technical uncertainties and ensure implementation. Thus, the US Department of Transportation and the US Nuclear Regulatory Commission, with assistance of staff from Oak Ridge National Laboratory, are preparing regulatory guidance which will present examples of acceptable methods for demonstrating compliance with the revised rules for large items. Concepts being investigated for inclusion in the pending guidance are discussed in this paper. Under current plans, the guidance will be issued for public comment before final issuance in 1997. (Author)

Development of guidance on applications of regulatory requirements for regulating large, contaminated equipment and large decommissioning and decontamination (D and D) components

International Nuclear Information System (INIS)

Pope, R.B.; Easton, E.P.; Cook, J.R.; Boyle, R.W.

1997-01-01

In 1985, the International Atomic Energy Agency issued revised regulations for the safe transport of radioactive material. Significant were major changes to requirements for Low Specific Activity material and Surface Contaminated Objects. As these requirements were adopted into regulations in the US, it was recognized that guidance on how to apply these requirements to large, contaminated/activated pieces of equipment and decommissioning and decontamination objects would be needed both by the regulators and those regulated to clarify technical uncertainties and ensure implementation. Thus, the US Department of Transportation and the US Nuclear Regulatory Commission, with assistance of staff from Oak Ridge National Laboratory, are preparing regulatory guidance which will present examples of acceptable methods for demonstrating compliance with the revised rules for large items. Concepts being investigated for inclusion in the pending guidance are discussed in this paper. Under current plans, the guidance will be issued for public comment before final issuance in 1997

47 CFR 1.1160 - Refunds of regulatory fees.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 1 2010-10-01 2010-10-01 false Refunds of regulatory fees. 1.1160 Section 1... Statutory Charges and Procedures for Payment § 1.1160 Refunds of regulatory fees. (a) Regulatory fees will be refunded, upon request, only in the following instances: (1) When no regulatory fee is required or...

Regulatory cross-cutting topics for fuel cycle facilities.

Energy Technology Data Exchange (ETDEWEB)

Denman, Matthew R.; Brown, Jason; Goldmann, Andrew Scott; Louie, David

2013-10-01

This report overviews crosscutting regulatory topics for nuclear fuel cycle facilities for use in the Fuel Cycle Research & Development Nuclear Fuel Cycle Evaluation and Screening study. In particular, the regulatory infrastructure and analysis capability is assessed for the following topical areas: Fire Regulations (i.e., how applicable are current Nuclear Regulatory Commission (NRC) and/or International Atomic Energy Agency (IAEA) fire regulations to advance fuel cycle facilities) Consequence Assessment (i.e., how applicable are current radionuclide transportation tools to support risk-informed regulations and Level 2 and/or 3 PRA) While not addressed in detail, the following regulatory topic is also discussed: Integrated Security, Safeguard and Safety Requirement (i.e., how applicable are current Nuclear Regulatory Commission (NRC) regulations to future fuel cycle facilities which will likely be required to balance the sometimes conflicting Material Accountability, Security, and Safety requirements.)

13 CFR 120.463 - Regulatory accounting-What are SBA's regulatory accounting requirements for SBA Supervised Lenders?

Science.gov (United States)

2010-01-01

... basis in accordance with Generally Accepted Accounting Principles (GAAP) as promulgated by the Financial Accounting Standards Board (FASB), supplemented by Regulatory Accounting Principles (RAP) as identified by... set forth in FASB Statement of Financial Accounting Standards No. 15, Accounting by Debtors and...

Virginia Power's regulatory reduction program

International Nuclear Information System (INIS)

Miller, G.D.

1996-01-01

Virginia Power has two nuclear plants, North Anna and Surry Power Stations, which have two units each for a total of four nuclear units. In 1992, the Nuclear Regulatory Commission solicited comments from the nuclear industry to obtain their ideas for reducing the regulatory burden on nuclear facilities. Pursuant to the new regulatory climate, Virginia Power developed an internal program to evaluate and assess the regulatory and self-imposed requirements to which they were committed, and to pursue regulatory relief or internal changes where possible and appropriate. The criteria were that public safety must be maintained, and savings must be significant. Up to the date of the conference, over US$22 million of one-time saving had been effected, and US$2.75 million in annual savings

76 FR 6587 - Pennsylvania Regulatory Program

Science.gov (United States)

2011-02-07

... [PA-159-FOR; OSM 2010-0017] Pennsylvania Regulatory Program AGENCY: Office of Surface Mining... remove a required amendment to the Pennsylvania regulatory program (the ``Pennsylvania program'') under... program amendment codified in the Federal regulations, Pennsylvania has submitted information that it...

The current regulatory requirements on optimisation and BAT in Sweden in the context of geological disposal

International Nuclear Information System (INIS)

Dverstorp, B.

2010-01-01

Bjorn Dverstorp, Swedish Radiation Safety authority (SSM) presented 'The current regulatory requirements on optimisation and BAT in Sweden in the context of geological disposal'. In Sweden, a nuclear waste repository will be evaluated according to both to general environmental legislation (the Environmental Code, SFS, 1998:808) and according to more specific requirements in the Act on Nuclear Activities (SFS, 1984:3) and the Radiation Protection Act (SFS, 1988:220). The evaluations according to these laws will be carried out according to two separate, but coordinated, legal-review and decision-making processes. This will be a basis for the siting process. Although the requirements on BAT and siting in the Environmental Code apply to radiological protection, they aim at a broader system optimisation. The more specific requirements on optimisation and BAT of radiological protection of geological disposal systems are given in the regulations associated with the Radiation Protection Act. The Swedish radiation protection regulations (SSM, 2009) comprise three corner stones: a risk target, environmental protection goals and the use of optimisation and BAT. In SSM' s guidance optimisation is defined as a means to reduce risk, guided by the results of risk calculations. In case of a conflict between BAT and optimisation, measures satisfying BAT should have priority. Application of optimisation and BAT on different timescales are described as well as for human intrusion scenarios. B. Dverstorp explained that because of uncertainties in the long term there is a need for additional arguments in the safety case in support of decision making. It is in this context that the requirements on optimisation and BAT should be seen as supplementary to the risk target, in providing evidence that the developer has taken into consideration, as far as reasonably possible, measures and options for reducing future doses and risks. Both principles focus on the proponent's work on developing

ENSI’s regulatory framework strategy

International Nuclear Information System (INIS)

2015-03-01

This short brochure issued by the Swiss Federal Nuclear Safety Inspectorate ENSI defines the organisation’s regulatory framework strategy. Six guiding principles are declared and discussed: Comprehensive harmonisation with relevant international requirements, basing the regulatory framework on existing, tried-and-tested regulations, issuing of its own guidelines only when it is necessary to do so, guidelines to be drawn up transparently and with the involvement of all stakeholders and basing the level of detail of its regulatory framework on hazard potential and risk

Ego depletion and positive illusions: does the construction of positivity require regulatory resources?

Science.gov (United States)

Fischer, Peter; Greitemeyer, Tobias; Frey, Dieter

2007-09-01

Individuals frequently exhibit positive illusions about their own abilities, their possibilities to control their environment, and future expectations. The authors propose that positive illusions require resources of self-control, which is considered to be a limited resource similar to energy or strength. Five studies revealed that people with depleted self-regulatory resources indeed exhibited a less-optimistic sense of their own abilities (Study 1), a lower sense of subjective control (Study 2), and less-optimistic expectations about their future (Study 3). Two further studies shed light on the underlying psychological process: Ego-depleted (compared to nondepleted) individuals generated/retrieved less positive self-relevant attributes (Studies 4 and 5) and reported a lower sense of general self-efficacy (Study 5), which both partially mediated the impact of ego depletion on positive self-views (Study 5).

The physics program of a high-luminosity asymmetric B Factory at SLAC

International Nuclear Information System (INIS)

1989-10-01

A high-luminosity asymmetric energy B Factory, proposed as an upgrade to the PEP storage ring at SLAC, provides the best opportunity to study CP violation as a means of testing the consistency of the Standard Model. If the phenomenon of CP violation is explained by the Standard Model simply through the non-zero angles and phase of the Kobayashi-Maskawa matrix, then there are precise relations between the K-M parameters and the various measurable CP-violating asymmetries in B meson decay. Should these consistency relations fail, the origin of CP violation must lie outside the Standard Model framework. Our measurements would then lead to the first experiment-driven extensions of the Standard Model. The B Factory will also carry out a varied, high-quality program of studies of other aspects of the physics of b quarks, as well as high-precision measurements in τ and charm physics. We describe a detailed series of measurements to be carried out in the first few years at a peak luminosity of 3 x 10 33 cm -2 sec -1 , the initial luminosity goal of the B Factory, as well as the program accessible to a larger data sample

14 CFR 313.4 - Major regulatory actions.

Science.gov (United States)

2010-01-01

...) PROCEDURAL REGULATIONS IMPLEMENTATION OF THE ENERGY POLICY AND CONSERVATION ACT § 313.4 Major regulatory... of actions shall not be deemed as major regulatory actions requiring an energy statement: (1) Tariff...

An Exploration of Analysis Software at SLAC through the Study of X(3872)

International Nuclear Information System (INIS)

Fischer, A.

2004-01-01

X(3872), a particle discovered by Belle Labs, has not yet been described in a sufficient enough way by any group to draw definitive conclusions about it. In order to verify the claims of Belle Labs and learn more about X(3872), Stanford Linear Accelerator Center (henceforth SLAC) has undertaken a project to analyze the particle, a subgroup of the BaBar project. The computing systems involved are complex; the tutorials for the software and new software releases both need constant testing and revision. Using a new software release, I tested tutorials for various software used by the BaBar group, including UNIX, Root, and CM2, in an effort to eventually analyze X(3872) data. The offline workbook for the BaBar software needs to be better maintained, and the CM2 tutorials need to be modified and updated. While none of my results contributed directly to the project (i.e. I have no results that add to information about X(3872)), improvement of the tutorials will streamline integration of new scientists into the BaBar group

Regulatory framework and safety requirements for new (gen III) reactors

International Nuclear Information System (INIS)

Mourlon, Sophie

2014-01-01

Sophie Mourlon, ASN Deputy General Director, described the international process to enhance safety between local safety authorities through organizations such as WENRA. Then she explained to the participants the regulatory issues for the next generation of NPPs

Regulatory Considerations for the Long Term Cooling Safe Shutdown Requirements of the Passive Residual Heat Removal Systems in Advanced Reactors

International Nuclear Information System (INIS)

Sim, S. K.; Bae, S. H.; Kim, Y. S.; Hwang, Min Jeong; Bang, Young Seok; Hwang, Taesuk

2016-01-01

USNRC approved safe shutdown at 215.6 .deg. C for a safe and long term cooling state for the redundant passive RHRSs by SECY-94-084. USNRC issued COLA(Combined Construction and Operating License) for the Levy County NP Unit-1/2 for the AP1000 passive RHRSs in 2014. Korea Hydro and Nuclear Power(KHNP) is developing APR+ and adopted Passive Auxiliary Feedwater System(PAFS) as a new passive RHRS design. Korea Institute of Nuclear Safety(KINS) has been developing regulatory guides for the advanced safety design features of the advanced ALWRs which has plan to construct in near future in Korea[5]. Safety and regulatory issues as well as the safe shut down requirements of the passive RHRS are discussed and considerations in developing regulatory guides for the passive RHRS are presented herein. Passive RHRSs have been introduced as new safety design features for the advanced reactors under development in Korea. These passive RHRSs have potential advantages over existing active RHRS, however, their functions are limited due to inherent ability of passive heat removal processes. It is high time to evaluate the performance of the passive PRHRs and develop regulatory guides for the safety as well as the performance analyses of the passive RHRS

Private Equity and Regulatory Capital

NARCIS (Netherlands)

Bongaerts, D.; Charlier, E.

2008-01-01

Regulatory Capital requirements for European banks have been put forward in the Basel II Capital Framework and subsequently in the Capital Requirements Directive (CRD) of the EU. We provide a detailed discussion of the capital requirements for private equity investments under the simple risk weight

Nuclear Regulatory Infrastructure in the Philippines

International Nuclear Information System (INIS)

Leonin, Teofilo V. Jr.

2015-01-01

Regulating the use of radioactive materials in the Philippines involves the adherence to legislation, regulations, standards and regulatory guides. It is based on a detailed review and assessment of the radiation safety program of owners and users of these materials and associated equipment against safety requirements and on additional verification of the operating practices and procedures. Republic Acts 5207 and 2067, both as amended, are implemented through the regulations which are titled Code of PNRI Regulations or CPRs are developed and issued together with supporting regulatory guides, Bulletins and other documents detailing the safety requirements. These issuance adhere to internationally accepted requirements on radiation protection, and nuclear safety and security, as well as safeguards. Design documents and technical Specifications of important radioactive materials, equipment and components are required to be submitted and reviewed by the PNRI before the issuance of an authorization in the form of a license Verification of adherence to regulations and safety requirements are periodically checked through the implementation of an inspection and enforcement program. The ISO certified regulatory management system of PNRI is documented in a QMS manual that provides guidance on all work processes. It involves systematic planning and evaluation of activities, multiple means of getting feedback on the work processes, and continuous efforts to improve its effectiveness. Efforts are implemented in order to strengthen the transparency openness, independence, technical competence and effectiveness of the regulatory body. (author)

Simulations of the BNL/SLAC/UCLA 1.6 cell emittance compensated photocathode RF gun low energy beam line

International Nuclear Information System (INIS)

Palmer, D.T.; Miller, R.H.; Winick, H.

1995-01-01

A dedicated low energy (2 to 10 MeV) experimental beam line is now under construction at Brookhaven National Laboratories Accelerator Test Facility (BNL/ATF) for photocathode RF gun testing and photoemission experiments. The design of the experimental line, using the 1.6 cell photocathode RF gun developed by the BNL/SLAC/UCLA RF gun collaboration is presented. Detailed beam dynamics simulations were performed for the 1.6 cell RF gun injector using a solenoidal emittance compensation technique. An experimental program for testing the 1.6 cell RF gun is presented. This program includes beam loading caused by dark current, higher order mode field measurements, integrated and slice emittance measurements using a pepper-pot and RF kicker cavity

First Measurements of the Longitudinal Bunch Profile at SLAC Using Coherent Smith-Purcell Radiation at 28GeV

International Nuclear Information System (INIS)

Arnold, R.; Molloy, S.; Woods, M.; Kimmitt, M.F.; Blackmore, V.; Doucas, G.; Ottewell, B.; Perry, C.

2011-01-01

Coherent Smith-Purcell radiation has been demonstrated as a technique for measuring the longitudinal profile of charged particles bunches in the low to intermediate energy range. However, with the advent of the International Linear Collider, the need has arisen for a non-invasive method of measuring the bunch profile at extremely high energies. Smith-Purcell radiation has been used for the first time in the multi-GeV regime to measure the longitudinal profile of the 28GeV SLAC beam. The experiment has both successfully determined the bunch length, and has also demonstrated its sensitivity to bunch profile changes. The challenges associated with this technique, and its prospects as a diagnostic tool are reported here.

Analytic Electron Trajectories in an Extremely Relativistic Helical Wiggler an Application to the Proposed SLAC E166 Experiment.

CERN Document Server

ThomasDonohue, John

2004-01-01

The proposed experiment SLAC E166 intends to generate circularly polarized gamma rays of energy 10 MeV by passing a 15 GeV electron beam through a meter long wiggler with approximately 400 periods. Using an analytic model formulated by Rullier and me, I present calculations of electron trajectories. At this extremely high energy the trajectories are described quite well by the model, and an extremely simple picture emerges, even for trajectories that that fail to encircle the axis of the wiggler. Our calculations are successfully compared with standard numerical integration of the Lorentz force equations of motion. In addition, the calculation of the spectrum and angular distribution of the radiated photons is easily carried out.

Study of the spin structure functions of the nucleon: the E143 experiment at SLAC

International Nuclear Information System (INIS)

Grenier, Philippe

1995-01-01

In this thesis, we present the results of the E143 experiment of deep inelastic scattering of 29 GeV polarized electrons from polarized NH 3 and ND 3 targets, at SLAC. The goal of the experiment is the measurement of the spin structure functions g 1 and g 2 of the nucleon which provide information on its internal spin structure. Experimentally, the structure functions are extracted from the measurement of cross section asymmetries. Our measured values of the first moment of g 1 are two and three standard deviations below the Ellis-Jaffe sum rule predictions, for the proton and for the deuteron, respectively. The Bjoerken sum rule, a QCD fundamental prediction, has been confirmed. We find the quark contribution to the nucleon spin to be around 30 pc. Our results on g 2 are well described by the Wandzura-Wilczek expression. (author) [fr

[European Union regulatory and quality requirements for botanical drugs and their implications for Chinese herbal medicinal products development].

Science.gov (United States)

Zhu, You-Ping

2017-06-01

This paper introduces regulatory pathways and characteristic quality requirements for marketing authorization of herbal medicinal products in the European Union（EU）, and the legal status and applications of "European Union list of herbal substances, preparations and combinations" and "European Union herbal monographs". Also introduced are Chinese herbs that have been granted the EU list entry, those with EU herbal monographs, and registered EU traditional herbal medicinal products with Chinese herbs as active ingredients. Special attention is paid to the technical details of three authorized EU herbal medicinal products (Veregen, Sativex and Episalvan) in comparison with Andrographis paniculata extract HMPL-004 that failed the phase Ⅲ clinical trial for ulcerative colitis. The paper further emphasizes the importance of enriching active fractions of herbal extracts and taking regulatory and quality considerations into account in early stage of botanical drug development. Copyright© by the Chinese Pharmaceutical Association.

Requirements for US regulatory approval of the International Thermonuclear Experimental Reactor (ITER)

International Nuclear Information System (INIS)

Petti, D.A.; Haire, J.C.

1993-12-01

The International Thermonuclear Experimental Reactor (ITER) is the first fusion machine that will have sufficient decay heat and activation product inventory to pose potential nuclear safety concerns. As a result, nuclear safety and environmental issues will be much more important in the approval process for the design, siting, construction, and operation of ITER in the United States than previous fusion devices, such as the Tokamak Fusion Test Reactor. The purpose of this report is (a) to provide an overview of the regulatory approval process for a Department of Energy (DOE) nuclear facility; (b) to present the dose limits used by DOE to protect workers, the public, and the environment from the risks of exposure to radiation and hazardous materials; (c) to discuss some key nuclear safety-related issues that must be addressed early in the Engineering Design Activities (EDA) to obtain regulatory approval; and (d) to provide general guidelines to the ITER Joint Central Team (JCT) concerning the development of a regulatory framework for the ITER project

Understanding how to maintain compliance in the current regulatory climate

International Nuclear Information System (INIS)

Bignell, D.T.; Burns, R.

1995-01-01

High level radioactive waste facilities must maintain compliance with all regulatory requirements, even those requirements that have been promulgated after the facility was placed into operation. Facilities must aggressively pursue compliance because environmental laws often impose strict liability for violations; therefore, an honest mistake is no defense. Radioactive waste management is constantly under the public microscope, particularly those facilities that handle high-level radioactive waste. The Savannah River Site has effectively met the challenges of regulatory compliance in its HLRW facilities and plans are being formulated to meet future regulatory requirements as well. Understanding, aggressively achieving, and clearly demonstrating compliance is essential for the continued operations of radioactive waste management facilities. This paper examines how HLRW facilities are impacted by regulatory requirements and how compliance in this difficult area is achieved and maintained

Regulatory requirements for the transport of radioactive materials in Canada

Energy Technology Data Exchange (ETDEWEB)

Garg, R. [Canadian Nuclear Safety Commission, Ottawa (Canada)

2004-07-01

Canada is a major producer and shipper of radioactive material. Each year more than a million packages are transported in Canada. The safety record with the transport of RAM in Canada has historically been excellent. There have never been any serious injuries, overexposure or fatality or environmental consequences attributable to the radioactive nature of such material being transported or being involved in a transport accident. In Canada, the Canadian Nuclear Safety Commission (CNSC) is the prime agency of the federal government entrusted with regulating all activities related to the use of nuclear energy and nuclear substances including the packaging and transport of nuclear substances. The mission of the CNSC is to regulate the use of nuclear energy and materials to protect health, safety, security of the person and the environment and to respect Canada's international commitments on the peaceful use of nuclear energy. The division of responsibility for the regulation of transport of radioactive material has been split between Transport Canada and the CNSC. The governing Transport Canada's regulations are Transport of Dangerous Goods (TDG) Regulations and the CNSC regulations are Packaging and Transport of Nuclear Substances Regulations (PTNSR). Canada has actively participated in the development of the IAEA regulations for the safe transport of radioactive material since 1960. As an IAEA member state, Canada generally follows the requirements of IAEA regulations with few deviations. The Nuclear Safety and Control Act (NSCA) strongly supports Canada's international obligations to ensure safe packaging, transport, storage and disposal of nuclear substances, prescribed equipment and prescribed information. Prescribed equipment and prescribed information are defined in the CNSC General Nuclear Safety and Control Regulations. This paper presents the current CNSC regulatory requirements and initiatives taken by the CNSC to improve its effectiveness and

Regulatory requirements for the transport of radioactive materials in Canada

International Nuclear Information System (INIS)

Garg, R.

2004-01-01

Canada is a major producer and shipper of radioactive material. Each year more than a million packages are transported in Canada. The safety record with the transport of RAM in Canada has historically been excellent. There have never been any serious injuries, overexposure or fatality or environmental consequences attributable to the radioactive nature of such material being transported or being involved in a transport accident. In Canada, the Canadian Nuclear Safety Commission (CNSC) is the prime agency of the federal government entrusted with regulating all activities related to the use of nuclear energy and nuclear substances including the packaging and transport of nuclear substances. The mission of the CNSC is to regulate the use of nuclear energy and materials to protect health, safety, security of the person and the environment and to respect Canada's international commitments on the peaceful use of nuclear energy. The division of responsibility for the regulation of transport of radioactive material has been split between Transport Canada and the CNSC. The governing Transport Canada's regulations are Transport of Dangerous Goods (TDG) Regulations and the CNSC regulations are Packaging and Transport of Nuclear Substances Regulations (PTNSR). Canada has actively participated in the development of the IAEA regulations for the safe transport of radioactive material since 1960. As an IAEA member state, Canada generally follows the requirements of IAEA regulations with few deviations. The Nuclear Safety and Control Act (NSCA) strongly supports Canada's international obligations to ensure safe packaging, transport, storage and disposal of nuclear substances, prescribed equipment and prescribed information. Prescribed equipment and prescribed information are defined in the CNSC General Nuclear Safety and Control Regulations. This paper presents the current CNSC regulatory requirements and initiatives taken by the CNSC to improve its effectiveness and efficiency

Measurement of the positron polarization at an helical undulator based positron source for the international linear collider ILC. The E-166 experiment at SLAC

Energy Technology Data Exchange (ETDEWEB)

Karim, Laihem

2008-06-05

A helical undulator based polarized positron source is forseen at a future International Linear Collider (ILC). The E-166 experiment has tested this scheme using a one meter long, short-period, pulsed helical undulator installed in the Final Focus Test Beam (FFTB) at SLAC. A low-emittance 46.6 GeV electron beam passing through this undulator generated circularly polarized photons with energies up to about 8 MeV. The generated photons of several MeV with circular polarization are then converted in a relatively thin target to generate longitudinally polarized positrons. Measurements of the positron polarization have been performed at 5 different energies of the positrons. In addition electron polarization has been determined for one energy point. For a comparison of the measured asymmetries with the expectations detailed simulations were necessary. This required upgrading GEANT4 to include the dominant polarization dependent interactions of electrons, positrons and photons in matter. The measured polarization of the positrons agrees with the expectations and is for the energy point with the highest polarization at 6MeV about 80%. (orig.)

76 FR 64043 - Iowa Regulatory Program

Science.gov (United States)

2011-10-17

...) Requirements for permits for special categories of mining. 27--40.41(207) Permanent regulatory program--small... DEPARTMENT OF THE INTERIOR Office of Surface Mining Reclamation and Enforcement 30 CFR Part 915 [Docket No. IA-016-FOR; Docket ID: OSM-2011-0014] Iowa Regulatory Program AGENCY: Office of Surface Mining...

Regulatory issues in the maintenance of Argentine nuclear power plants

International Nuclear Information System (INIS)

Castro, E.; Caruso, G.

1997-01-01

The influence of maintenance activities upon nuclear safety and their relevance as means to detect and prevent aging make them play an outstanding role among the fields of interest of the Argentine nuclear regulatory body (ENREN). Such interest is reinforced by the fact that the data obtained during maintenance are used - among other - as inputs in the Probabilistic Safety Analyses required for those nuclear power plants. This paper provides a brief description of the original requirements by the regulatory body concerning maintenance, of the factors that led to review the criteria involved in such requirements and of the key items identified during the reviewing process. The latter shall be taken into account in the maintenance regulatory policy, for the consequent issue of new requirements from the utilities and for the eventual publication of a specific regulatory standard. (author)

FORECAST: Regulatory effects cost analysis software annual

International Nuclear Information System (INIS)

Lopez, B.; Sciacca, F.W.

1991-11-01

Over the past several years the NRC has developed a generic cost methodology for the quantification of cost/economic impacts associated with a wide range of new or revised regulatory requirements. This methodology has been developed to aid the NRC in preparing Regulatory Impact Analyses (RIAs). These generic costing methods can be useful in quantifying impacts both to industry and to the NRC. The FORECAST program was developed to facilitate the use of the generic costing methodology. This PC program integrates the major cost considerations that may be required because of a regulatory change. FORECAST automates much of the calculations typically needed in an RIA and thus reduces the time and labor required to perform these analysis. More importantly, its integrated and consistent treatment of the different cost elements should help assure comprehensiveness, uniformity, and accuracy in the preparation of needed cost estimates

Regulatory agencies and regulatory risk

OpenAIRE

Knieps, Günter; Weiß, Hans-Jörg

2008-01-01

The aim of this paper is to show that regulatory risk is due to the discretionary behaviour of regulatory agencies, caused by a too extensive regulatory mandate provided by the legislator. The normative point of reference and a behavioural model of regulatory agencies based on the positive theory of regulation are presented. Regulatory risk with regard to the future behaviour of regulatory agencies is modelled as the consequence of the ex ante uncertainty about the relative influence of inter...

The E142 SLAC experiment: measurement of the neutron gn1(x) spin structure function

International Nuclear Information System (INIS)

Roblin, Y.

1995-01-01

This thesis describes the E142 experiment which has been carried out at the Stanford Linear Accelerator (SLAC), USA, from October to December 1992. This experiment of polarized inelastic scattering of a 22.6 GeV electron beam on a polarized helium 3 target has allowed the first measurement of the neutron g n 1 (x) spin structure function. The knowledge of this structure function gives informations on the nucleon spin structure. On the other hand, the g n 1 (x) structure function integral value on the 0 2 mean value of 2 GeV 2 after some extrapolations. This value is at about two standard deviations away from the theoretical predictions of the Ellis-Jaffe rule. Thanks to the existing experimental results for the proton (E143 experiment), the Bjorken sum rule has been precisely tested and is perfectly compatible with the theoretical value. The results have allowed to estimate the nucleon spin fraction carried by the quarks. (J.S.). 86 refs., 58 figs., 13 tabs

A Review on Regulatory Enforcement Policy

International Nuclear Information System (INIS)

Lim, Ji Han; Lee, Kyung Joo; Choi, Young Sung

2017-01-01

This paper examine the meaning and principle of enforcement through examples from other countries. Regulatory enforcement is the last stage of safety regulation and how it is exercised when one failing to meet regulatory requirements can have significant ripple effect across the industry. Thus, right philosophy and principle should be established. It is not recommended to emphasize neither deterrence approach nor behavior modification approach. This should be also taken into consideration when setting up the principle and system of regulatory enforcement. In the process of Vienna Declaration, Europe and the U.S showed the fundamental differences in their approaches to safety regulation. Considering this, it is required to remain cautious at all times on what to be improved in the aspect of internal consistency within our system and also in the aspect of procedure.

A test facility for the international linear collider at SLAC end station a for prototypes of beam delivery and IR components

International Nuclear Information System (INIS)

Hildreth, M.D.; Erickson, R.; Frisch, J.

2006-01-01

The SLAC Linac can deliver damped bunches with ILC parameters for bunch charge and bunch length to End Station A. A 10Hz beam at 28.5 GeV energy can be delivered there, parasitic with PEP-II operation. We plan to use this facility to test prototype components of the Beam Delivery System and Interaction Region. We discuss our plans for this ILC Test Facility and preparations for carrying out experiments related to collimator wakefields and energy spectrometers. We also plan an interaction region mockup to investigate effects from backgrounds and beam-induced electromagnetic interference. (author)

Regulatory control of fuel design and manufacturing

International Nuclear Information System (INIS)

1994-01-01

The regulatory control of the design and manufacturing of the nuclear fuel and of the control rods aims to ensure conformance to set requirements during normal operating conditions, anticipated operational transients and postulated accident conditions. The regulatory control of design, manufacturing, receiving inspections and the start of operation of the nuclear fuel are specified in the guide. The regulatory control procedure also applies to the control rods and the shield elements

Final Design of the SLAC P2 Marx Klystron Modulator

Energy Technology Data Exchange (ETDEWEB)

Kemp, M.A.; Benwell, A.; Burkhart, C.; Larsen, R.; MacNair, D.; Nguyen, M.; Olsen, J.; /SLAC

2011-11-08

The SLAC P2 Marx has been under development for two years, and follows on the P1 Marx as an alternative to the baseline klystron modulator for the International Linear Collider. The P2 Marx utilizes a redundant architecture, air-insulation, a control system with abundant diagnostic access, and a novel nested droop correction scheme. This paper is an overview of the design of this modulator. There are several points of emphasis for the P2 Marx design. First, the modulator must be compatible with the ILC two-tunnel design. In this scheme, the modulator and klystron are located within a service tunnel with limited access and available footprint for a modulator. Access to the modulator is only practical from one side. Second, the modulator must have high availability. Robust components are not sufficient alone to achieve availability much higher than 99%. Therefore, redundant architectures are necessary. Third, the modulator must be relatively low cost. Because of the large number of stations in the ILC, the investment needed for the modulator components is significant. High-volume construction techniques which take advantage of an economy of scale must be utilized. Fourth, the modulator must be simple and efficient to maintain. If a modulator does become inoperable, the MTTR must be small. Fifth, even though the present application for the modulator is for the ILC, future accelerators can also take advantage of this development effort. The hardware, software, and concepts developed in this project should be designed such that further development time necessary for other applications is minimal.

A comparison of immunotoxic effects of nanomedicinal products with regulatory immunotoxicity testing requirements.

Science.gov (United States)

Giannakou, Christina; Park, Margriet Vdz; de Jong, Wim H; van Loveren, Henk; Vandebriel, Rob J; Geertsma, Robert E

2016-01-01

Nanomaterials (NMs) are attractive for biomedical and pharmaceutical applications because of their unique physicochemical and biological properties. A major application area of NMs is drug delivery. Many nanomedicinal products (NMPs) currently on the market or in clinical trials are most often based on liposomal products or polymer conjugates. NMPs can be designed to target specific tissues, eg, tumors. In virtually all cases, NMPs will eventually reach the immune system. It has been shown that most NMs end up in organs of the mononuclear phagocytic system, notably liver and spleen. Adverse immune effects, including allergy, hypersensitivity, and immunosuppression, have been reported after NMP administration. Interactions of NMPs with the immune system may therefore constitute important side effects. Currently, no regulatory documents are specifically dedicated to evaluate the immunotoxicity of NMs or NMPs. Their immunotoxicity assessment is performed based on existing guidelines for conventional substances or medicinal products. Due to the unique properties of NMPs when compared with conventional medicinal products, it is uncertain whether the currently prescribed set of tests provides sufficient information for an adequate evaluation of potential immunotoxicity of NMPs. The aim of this study was therefore, to compare the current regulatory immunotoxicity testing requirements with the accumulating knowledge on immunotoxic effects of NMPs in order to identify potential gaps in the safety assessment. This comparison showed that immunotoxic effects, such as complement activation-related pseudoallergy, myelosuppression, inflammasome activation, and hypersensitivity, are not readily detected by using current testing guidelines. Immunotoxicity of NMPs would be more accurately evaluated by an expanded testing strategy that is equipped to stratify applicable testing for the various types of NMPs.

Defining regulatory requirements for water supply systems in Vietnam

Directory of Open Access Journals (Sweden)

Deryushev Leonid Georgiyevich

2014-01-01

Full Text Available In the article the authors offer their suggestions for improving the reliability of the standardization requirements for water supply facilities in Vietnam, as an analog of building regulations of Russia 31.13330.2012. In Russia and other advanced countries the reliability of the designed water supply systems is usual to assess quantitatively. Guidelines on the reliability assessment of water supply systems and facilities have been offered by many researchers, but these proposals are not officially approved. Some methods for assessing the reliability of water supply facilities are informally used in practice when describing their quality. These evaluation methods are simple and useful. However, the given estimations defy common sense and regulatory requirements used by all the organizations, ministries and departments, for example, of Russia, in the process of allowances for restoration and repair of water supply facilities. Inadequacy of the water supply facilities assessment is shown on the example of assessing the reliability of pipeline system. If we take MTBF of specific length of the pipeline as reliability index for a pipeline system, for example, 5 km, a pipeline of the similar gauge, material and working conditions with the length of 5 m, according to the estimation on the basis of non-official approach, must have a value of MTBF 1000 times greater than with the length of 5 km. This conclusion runs counter to common sense, for the reason that all the pipes in the area of 5 km are identical, have the same load and rate of wear (corrosion, fouling, deformation, etc.. It was theoretically and practically proved that products of the same type in the same operating conditions (excluding determined impact of a person, work as an entity, which MTBF is equal to the average lifetime. It is proposed to take the average service life as a reliability indicator of a pipeline. Durability, but not failsafety of the pipe guarantees pipeline functioning

Regulatory issues in accreditation of toxicology laboratories.

Science.gov (United States)

Bissell, Michael G

2012-09-01

Clinical toxicology laboratories and forensic toxicology laboratories operate in a highly regulated environment. This article outlines major US legal/regulatory issues and requirements relevant to accreditation of toxicology laboratories (state and local regulations are not covered in any depth). The most fundamental regulatory distinction involves the purposes for which the laboratory operates: clinical versus nonclinical. The applicable regulations and the requirements and options for operations depend most basically on this consideration, with clinical toxicology laboratories being directly subject to federal law including mandated options for accreditation and forensic toxicology laboratories being subject to degrees of voluntary or state government–required accreditation.

The regulatory framework in the UK

International Nuclear Information System (INIS)

O'Sullivan, R.

1984-01-01

The subject is covered in sections, headed: basic regulatory requirements covering the transport of radioactive material in the UK; responsibility for safety (competent authority; provision of regulations; implementation of regulations (international and national); design of transport flask; safety case; testing; assessment; approval certificate; compliance assurance; administration); advice and information on the regulatory safety standards. (U.K.)

Governmental, Legal and Regulatory Framework for Safety. General Safety Requirements. Part 1 (French Edition); Cadre gouvernemental, legislatif et reglementaire de la surete. Prescriptions generales de surete. Partie 1

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-11-15

The objective of this publication is to establish requirements in respect of the governmental, legal and regulatory framework for safety. It covers the essential aspects of the framework for establishing a regulatory body and taking other actions necessary to ensure the effective regulatory control of facilities and activities utilized for peaceful purposes. Other responsibilities and functions, such as liaison within the global safety regime and on support services for safety (including radiation protection), emergency preparedness and response, nuclear security, and the State system of accounting for and control of nuclear material, are also covered.

Governmental, Legal and Regulatory Framework for Safety. General Safety Requirements. Part 1 (Spanish Edition); Marco gubernamental, juridico y regulador para la seguridad. Requisitos de Seguridad Generales. Parte 1

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-11-15

The objective of this publication is to establish requirements in respect of the governmental, legal and regulatory framework for safety. It covers the essential aspects of the framework for establishing a regulatory body and taking other actions necessary to ensure the effective regulatory control of facilities and activities utilized for peaceful purposes. Other responsibilities and functions, such as liaison within the global safety regime and on support services for safety (including radiation protection), emergency preparedness and response, nuclear security, and the State system of accounting for and control of nuclear material, are also covered.

Complete Genomes of Bacillus coagulans S-lac and Bacillus subtilis TO-A JPC, Two Phylogenetically Distinct Probiotics.

Science.gov (United States)

Khatri, Indu; Sharma, Shailza; Ramya, T N C; Subramanian, Srikrishna

2016-01-01

Several spore-forming strains of Bacillus are marketed as probiotics due to their ability to survive harsh gastrointestinal conditions and confer health benefits to the host. We report the complete genomes of two commercially available probiotics, Bacillus coagulans S-lac and Bacillus subtilis TO-A JPC, and compare them with the genomes of other Bacillus and Lactobacillus. The taxonomic position of both organisms was established with a maximum-likelihood tree based on twenty six housekeeping proteins. Analysis of all probiotic strains of Bacillus and Lactobacillus reveal that the essential sporulation proteins are conserved in all Bacillus probiotic strains while they are absent in Lactobacillus spp. We identified various antibiotic resistance, stress-related, and adhesion-related domains in these organisms, which likely provide support in exerting probiotic action by enabling adhesion to host epithelial cells and survival during antibiotic treatment and harsh conditions.

Waste management from reprocessing: a stringent regulatory requirements for high quality conditioned residues

International Nuclear Information System (INIS)

Bordier, J. C.; Greneche, D.; Devezeaux, J. G.; Dalcorso, J.

2000-01-01

Nuclear waste production and management in France is governed by safety requirements imposed to all operators. French nuclear safety relies on two basic principles: · Responsibility of the nuclear operator, which expands to waste generated, · Safety basic objectives issued by national Safety Authority. For a long time the regulatory framework for waste production and management has been satisfactorily applied and has benefited to each actor of the process. LLW/MLW and HLW nuclear waste are currently conditioned in safe matrices or packages either likely to be disposed in surface repositories or designed with the intention to be disposed underground according to their radioactive content. France is looking into the case of VLLW and has already carried out a design for future disposal, the design being in the pipe. Other types of waste (i. e. radium bearing waste, graphite, and tritium content waste) are also considered in the whole framework of French waste management. (author)

Canadian and international approaches to regulatory effectiveness

International Nuclear Information System (INIS)

Lojk, R.

2014-01-01

Regulatory effectiveness is an important attribute of any regulator, particularly nuclear regulators. As the nuclear industry has matured, and as the social landscape has changed, so have views on what constitutes regulatory effectiveness. Canada has evolved its regulatory structure and modernized its legislative framework and technical requirements and guidance over time. In addition, Canada continues to collaborate with international agencies, particularly the NEA and the IAEA, to ensure that there is a common understanding of the indicators and key attributes of regulatory effectiveness. This paper discusses Canadian and international views on the subject, including perspectives from other industries. (author)

A 3D bioprinting exemplar of the consequences of the regulatory requirements on customized processes.

Science.gov (United States)

Hourd, Paul; Medcalf, Nicholas; Segal, Joel; Williams, David J

2015-01-01

Computer-aided 3D printing approaches to the industrial production of customized 3D functional living constructs for restoration of tissue and organ function face significant regulatory challenges. Using the manufacture of a customized, 3D-bioprinted nasal implant as a well-informed but hypothetical exemplar, we examine how these products might be regulated. Existing EU and USA regulatory frameworks do not account for the differences between 3D printing and conventional manufacturing methods or the ability to create individual customized products using mechanized rather than craft approaches. Already subject to extensive regulatory control, issues related to control of the computer-aided design to manufacture process and the associated software system chain present additional scientific and regulatory challenges for manufacturers of these complex 3D-bioprinted advanced combination products.

Decommissioning of uranium mines and mills - Canadian regulatory approach and experience

International Nuclear Information System (INIS)

Whitehead, W.

1986-09-01

At the time of the recent closures of the Agnew Lake, Beaverlodge and Madawaska Mines Limited uranium mining and milling facilities, several relevant regulatory initiatives, including the development of decommissioning criteria, were underway, or contemplated. In the absence of precedents, the regulatory agencies and companies involved adopted approaches to the decommissioning of these facilities that reflected site specific circumstances, federal and provincial regulatory requirements, and generally accepted principles of good engineering practice and environmental protection. This paper summarizes related historical and current regulatory policies, requirements and guidelines; including those implemented at the three decommissioned sites

Proceedings of the 25th SLAC Summer Institute on Particle Physics: Physics of Leptons (SSI97) , Stanford, CA, August 4-15, 1997

International Nuclear Information System (INIS)

Deporcel, Lilian

1998-01-01

One hundred ninety-eight physicists from 16 countries gathered at SLAC from August 4 to 15, 1997 to attend the XXV SLAC Summer Institute on Particle Physics. The theme of the school was ''The Physics of Leptons'', commemorating a century since the electron, the first lepton, was discovered. We heard about the electron's role as a probe of the structure of matter, as well as the beautifully precise tests of charged-lepton universality in Z 0 decays. The focus of the school then shifted from the charged leptons to their weak partners, the neutrinos. Summer Institute attendees were not surprised in early 1998 by Super-Kamiokande's announcement of evidence for neutrino mass. After all, they had already seen the mounting evidence, both solar and atmospheric, the preceding August, in a comprehensive review of all nonaccelerator-based neutrino oscillation experiments, as well as a topical conference report from Super-Kamiokande. We also heard about the past, present, and future of reactor- and accelerator-based oscillation experiments, including the prospects for terrestrial tests of the atmospheric neutrino anomaly. Leptons in cosmology and as harbingers of physics beyond the Standard Model were the subject of two more lecture series. The three-day topical conference concluding the Institute was highlighted by the Super-Kamiokande neutrino results, and Beppo-Sax's report on the cosmological origin of gamma-ray bursters. As for terrestrial accelerators, SLC, LEP, and the Tevatron put increasing pressure on the electroweak sector through precision measurements, but all direct searches for new phenomena still came up empty

Franchise Values, Regulatory Monitoring, and Capital Requirements in Optimal Bank Regulation

DEFF Research Database (Denmark)

Andersen, Thomas Barnebeck; Harr, Thomas

2008-01-01

This paper demonstrates that financial deregulation is likely to make standard prudential regulatory instruments less effective in curbing excessive risk-taking incentives among banks. This has interesting implications for optimal bank regulation. When there is an increase in competition, the opt...

Regulatory Control of Radiation Sources. Safety Guide

International Nuclear Information System (INIS)

2009-01-01

This Safety Guide is intended to assist States in implementing the requirements established in Safety Standards Series No. GS-R-1, Legal and Governmental Infrastructure for Nuclear, Radiation, Radioactive Waste and Transport Safety, for a national regulatory infrastructure to regulate any practice involving radiation sources in medicine, industry, research, agriculture and education. The Safety Guide provides advice on the legislative basis for establishing regulatory bodies, including the effective independence of the regulatory body. It also provides guidance on implementing the functions and activities of regulatory bodies: the development of regulations and guides on radiation safety; implementation of a system for notification and authorization; carrying out regulatory inspections; taking necessary enforcement actions; and investigating accidents and circumstances potentially giving rise to accidents. The various aspects relating to the regulatory control of consumer products are explained, including justification, optimization of exposure, safety assessment and authorization. Guidance is also provided on the organization and staffing of regulatory bodies. Contents: 1. Introduction; 2. Legal framework for a regulatory infrastructure; 3. Principal functions and activities of the regulatory body; 4. Regulatory control of the supply of consumer products; 5. Functions of the regulatory body shared with other governmental agencies; 6. Organization and staffing of the regulatory body; 7. Documentation of the functions and activities of the regulatory body; 8. Support services; 9. Quality management for the regulatory system.

A Precise Measurement of the Spin Structure Functions G**P(2) G**D(2) from SLAC Experiment E155X

Energy Technology Data Exchange (ETDEWEB)

McNulty, D

2003-12-18

A precision measurement of the deep inelastic polarized structure functions g{sub 2}{sup p} (x, Q{sup 2}) and g{sub 2}{sup d} (x, Q{sup 2}) and the virtual photon asymmetries A{sub 2}{sup p}(x, Q{sup 2}) and A{sub 2}{sup d}(x, Q{sup 2}) has been made by the E155x collaboration in the ranges 0.02 < x < 0.8 and 0.7 (GeV/c){sup 2} < Q{sup 2} < 20 (GeV/c){sup 2}. The transverse asymmetry (A{sub {perpendicular}}) was measured at SLAC using 29.1 and 32.3 GeV longitudinally polarized electrons incident on transversely polarized target protons and deuterons; the scattered electrons were detected by three fixed angle spectrometers at 2.75{sup o}, 5.5{sup o}, and 10.5{sup o} from the beam line. g{sub 2} was extracted using the measured A{sub {perpendicular}}, an E155 phenomenological fit to g{sub 1}/F{sub 1}, and the SLAC fit to R(x, Q{sup 2}); the function F{sub 1} was obtained from the most recent NMC fit to F{sub 2}(x, Q{sup 2}). The errors on g{sub 2} for both proton and deuteron are more than three times smaller than those of the previously existing world data set, thus enabling the data to resolve clearly between g{sub 2}{sup ww} and zero as well as make distinctions between various models. In addition, the Burkhardt-Cottingham and Efremov-Leader-Teryaev sum rules were evaluated over the measured kinematic region, as well as the d{sub 2} twist-3 matrix element for the proton and neutron.

THE BOSS EMISSION-LINE LENS SURVEY. II. INVESTIGATING MASS-DENSITY PROFILE EVOLUTION IN THE SLACS+BELLS STRONG GRAVITATIONAL LENS SAMPLE

Energy Technology Data Exchange (ETDEWEB)

Bolton, Adam S.; Brownstein, Joel R.; Shu Yiping; Arneson, Ryan A. [Department of Physics and Astronomy, University of Utah, 115 South 1400 East, Salt Lake City, UT 84112 (United States); Kochanek, Christopher S. [Department of Astronomy and Center for Cosmology and Astroparticle Physics, Ohio State University, Columbus, OH 43210 (United States); Schlegel, David J. [Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Eisenstein, Daniel J. [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, MS 20, Cambridge, MA 02138 (United States); Wake, David A. [Department of Astronomy, Yale University, New Haven, CT 06520 (United States); Connolly, Natalia [Department of Physics, Hamilton College, Clinton, NY 13323 (United States); Maraston, Claudia [Institute of Cosmology and Gravitation, University of Portsmouth, Portsmouth PO1 3FX (United Kingdom); Weaver, Benjamin A., E-mail: bolton@astro.utah.edu [Center for Cosmology and Particle Physics, New York University, New York, NY 10003 (United States)

2012-09-20

We present an analysis of the evolution of the central mass-density profile of massive elliptical galaxies from the SLACS and BELLS strong gravitational lens samples over the redshift interval z Almost-Equal-To 0.1-0.6, based on the combination of strong-lensing aperture mass and stellar velocity-dispersion constraints. We find a significant trend toward steeper mass profiles (parameterized by the power-law density model with {rho}{proportional_to}r {sup -{gamma}}) at later cosmic times, with magnitude d < {gamma} > /dz = -0.60 {+-} 0.15. We show that the combined lens-galaxy sample is consistent with a non-evolving distribution of stellar velocity dispersions. Considering possible additional dependence of <{gamma} > on lens-galaxy stellar mass, effective radius, and Sersic index, we find marginal evidence for shallower mass profiles at higher masses and larger sizes, but with a significance that is subdominant to the redshift dependence. Using the results of published Monte Carlo simulations of spectroscopic lens surveys, we verify that our mass-profile evolution result cannot be explained by lensing selection biases as a function of redshift. Interpreted as a true evolutionary signal, our result suggests that major dry mergers involving off-axis trajectories play a significant role in the evolution of the average mass-density structure of massive early-type galaxies over the past 6 Gyr. We also consider an alternative non-evolutionary hypothesis based on variations in the strong-lensing measurement aperture with redshift, which would imply the detection of an 'inflection zone' marking the transition between the baryon-dominated and dark-matter halo-dominated regions of the lens galaxies. Further observations of the combined SLACS+BELLS sample can constrain this picture more precisely, and enable a more detailed investigation of the multivariate dependences of galaxy mass structure across cosmic time.

Fabrication of sterile experimental radiopharmaceuticals: technical and regulatory requirements

International Nuclear Information System (INIS)

Briand, S.

2008-03-01

The radiopharmaceuticals devoted to the biomedical research were the object of the directive 2001/20/C.E. transposition that defined again the conditions of implementation of biomedical research using drugs at human use, whom authorization is delivered by A.f.s.s.a.p.s.. In an other hand the law 2006-686 of the 13. june 2006 ( called law T.S.N.) has modified the regulatory dispositions relative to the radiation protection norms. These new dispositions allow to the health facilities to realize their research projects without difficulties for experimental drugs supply. (N.C.)

Structure and drafting of safeguards regulatory documents

International Nuclear Information System (INIS)

Cole, R.J.; Bennett, C.A.; Edelhertz, H.; Wood, M.T.; Brown, R.J.; Roberts, F.P.

1977-09-01

This study develops hypothesis about the relation between the structure and drafting of safeguards regulatory documents and the ability of document users to understand and implement them in a way that reflects the intent and requirements of the NRC. Four decisions are needed to improve communication: (1) Should improvement of safeguards regulatory documents as communication instruments be an explicit NRC program. (2) What specific methods of communication should be the focus of improvement efforts. (3) What actions to improve communications are feasible and desirable. (4) How should the NRC divide its available effort and resources among desirable actions in order to provide the most effective communication through regulatory documents. This volume contains: introduction, conceptual bases, legal requirements, targets, choice of documents, preparation of documents, readability, and further study of recommended changes in structure and drafting

Regulatory difficulties in a developing country

International Nuclear Information System (INIS)

Jacobs, W.R. Jr.

1978-01-01

The regulatory agency assigned the task of regulating the initial entry into the field of nuclear power generation by a developing country has a very difficult job. Based on the authors' experience during the start-up and initial operation of Ko-Ri Unit I, the first power reactor in the Republic of Korea, observations on regulatory difficulties and recommendations for improved regulatory effectiveness are offered. The problem areas can be loosely grouped into three general categories: (1) Lack of adequate technical knowledge which is the basis for all effective regulation; (2) Difficulties with understanding and utilization of the required regulatory documentation; (3) Failure to establish the proper regulatory environment. Examples are cited from actual experience during the Ko-Ri Unit I start-up to demonstrate the impact that regulatory activities can have on a plant construction and testing programme. The problems encountered are not unique to developing countries but also exist in the United States of America. Recommendations are offered which should be beneficial to either newly formed regulatory agencies or agencies wishing to improve their abilities and effectiveness. These include: (1) Additional training of regulatory inspectors in plant operations; (2) Additional experience gained by participation in regulatory activities in other countries; (3) Increased attention given to regulatory documents, especially plant technical specifications; (4) Establishment of formal lines of communication between the utility and the regulatory agency; (5) Clear definition of regulatory responsibilities to avoid areas of overlapping jurisdiction; (6) Active participation by the regulatory staff very early in the project. It is hoped that these and other recommendations offered will greatly improve regulatory effectiveness and at the same time demonstrate that when the decision is made to 'go nuclear', a strong commitment must be made to develop and support a technically

A regulatory perspective on design and performance requirements for engineered systems in high-level waste

International Nuclear Information System (INIS)

Bernero, R.M.

1992-01-01

For engineered systems, this paper gives an overview of some of the current activities at the U.S. Nuclear Regulatory Commission (NRC), with the intent of elucidating how the regulatory process works in the management of high-level waste (HLW). Throughout the waste management cycle, starting with packaging and transportation, and continuing to final closure of a repository, these activities are directed at taking advantage of the prelicensing consultation period, a period in which the NRC, DOE and others can interact in ways that will reduce regulatory, technical and institutional uncertainties, and open the path to development and construction of a deep geologic repository for permanent disposal of HLW. Needed interactions in the HLW program are highlighted. Examples of HLW regulatory activities are given in discussions of a multipurpose-cask concept and of current NRC work on the meaning of the term substantially complete containment

78 FR 1634 - Regulatory Agenda

Science.gov (United States)

2013-01-08

... amendments include updates to organizational information, use of the term ``disability'' in lieu of the term.../00/13 Regulatory Flexibility Analysis Required: No. Agency Contact: Robert W. Cosgrove, External...

78 FR 44329 - Regulatory Agenda

Science.gov (United States)

2013-07-23

... amendments include updates to organizational information, use of the term ``disability'' in lieu of the term.../00/13 Regulatory Flexibility Analysis Required: No. Agency Contact: Robert W. Cosgrove, External...

Cost-benefit and regulatory decision making

International Nuclear Information System (INIS)

Harvie, J.

1996-01-01

The Atomic Energy Control Board is investigating the feasibility of developing methods for factoring cost-benefit considerations into its regulatory decision-making. This initiative results, in part, from the federal government policy requiring cost-benefit considerations to be taken into account in regulatory processes, and from the recommendations of an Advisory Panel on Regulatory Review in 1993, submitted to the Minister of Natural Resources Canada. One of these recommendations stated: 'that mechanisms be developed to examine cost benefit issues and work towards some consensus of opinion among stake holders: a task force on the subject could be an appropriate starting point'. (author)

U.S. regulatory requirements for nuclear plant license renewal: The B and W Owners Group License Renewal Program

International Nuclear Information System (INIS)

Staudinger, Deborah K.

2004-01-01

This paper discusses the current U.S. Regulatory Requirements for License Renewal and describes the Babcock and Wilcox Owners Group (B and WOG) Generic License Renewal Program (GLRP). The B and W owners, recognizing the need to obtain the maximum life for their nuclear generating units, embarked on a program to renew the licenses of the seven reactors in accordance with the requirements of the Atomic Energy Act of 1954 and further defined by Title 10 of the Code of Federal Regulation Part 54 (10 CFR 54). These reactors, owned by five separate utilities, are Pressurized Water Reactors (PWR) ranging in net rated capacity from approximately 800 to 900 MW. The plants, predominately constructed in the 70s, have USNRC Operating Licenses that expire between 2013 to 2017. (author)

Regulatory perspectives of concept assessment

International Nuclear Information System (INIS)

Flavelle, Peter A.

1987-09-01

The Atomic Energy Control Board is the head agency for the regulatory review of the Assessment of the Canadian Concept for Nuclear Fuel Waste Disposal being done by Atomic Energy of Canada Limited and Ontario Hydro. This paper describes the regulatory perspective of how the Concept Assessment could demonstrate the feasibility of a disposal conforming to regulatory requirements. The long-term aspects of Concept Assessment encourage the use of various predictive techniques for different time scales. Each technique will have a different potential for establishing confidence in the predictions. The predicted performance of a facility during operation should have a very high confidence, as it can be based on standard engineering calculations and the predictions can be validated later by monitoring during operation. The predictions of the transient period following closure of the facility should achieve a medium level of confidence, since they can be based on extrapolations of predictions of operational performance, using models that can be calibrated with monitoring data and with averaged input data derived from natural analog studies. Predictions based on fundamental processes will have a medium level of confidence when made to intermediate times after closure. Long-term predictions using generic or typical input data or Monte Carlo calculations of simplified models will have the least confidence and yet they can still contribute to the confidence that the disposal concept will conform to regulatory requirements

Regulatory Requirements to Combat Illicit Trafficking of Hazardous Materials

International Nuclear Information System (INIS)

Hussein, A.Z.; Zakaria, Kh.M.

2011-01-01

Since more than a decade illicit Trafficking of hazardous ( CBRNE), materials ( chemical, biological, radiological, nuclear and explosive ) has been identified as a key threat in national, regional, inter regional and international strategies. An Effective response to hazardous materials (CBRNE) risk and threat were realized to require a very high level of cooperation and coordination between various governments and their responsible organizations and authorities of regional and international partner. While improper policy of actions may easily be exploited by non- state members to (CBRNE) trafficking which may lead to develop weapon of mass destruction (WMD). Such strategy are of paramount important between all levels of the states and among regional agreements through comprehensive tailored assistance packages (e.g. export control, illicit trafficking of hazardous materials, redirection of scientist, emergency planning, crisis response safety and security culture. Capacity building, action plans and instruments for stability are necessary actions for efficient combating against illicit trafficking of hazardous materials. Regarding the needs of assessment phase, assistance must be based on data collection, analysis and prioritization of implanting the regulatory controls. Several activities have to be conducted to reduce CBRNE threat. The one- by- one approach, covering either nuclear and radioactive or chemical or biological materials has to be implanted on the country basis performance to mitigate CBRNE hazardous risk. On several consequent phases of intervention dealing with CBRNE risk mitigation the country has to establish a network of local, regional and international capabilities. Such network is setting up the mechanism for the country needs identifications, the guidelines for data collection, for data platform maintenance and update, the data assessment and the competent and operative organizations. This network will be to strengthen the long - term

Complete Genomes of Bacillus coagulans S-lac and Bacillus subtilis TO-A JPC, Two Phylogenetically Distinct Probiotics

Science.gov (United States)

Ramya, T. N. C.; Subramanian, Srikrishna

2016-01-01

Several spore-forming strains of Bacillus are marketed as probiotics due to their ability to survive harsh gastrointestinal conditions and confer health benefits to the host. We report the complete genomes of two commercially available probiotics, Bacillus coagulans S-lac and Bacillus subtilis TO-A JPC, and compare them with the genomes of other Bacillus and Lactobacillus. The taxonomic position of both organisms was established with a maximum-likelihood tree based on twenty six housekeeping proteins. Analysis of all probiotic strains of Bacillus and Lactobacillus reveal that the essential sporulation proteins are conserved in all Bacillus probiotic strains while they are absent in Lactobacillus spp. We identified various antibiotic resistance, stress-related, and adhesion-related domains in these organisms, which likely provide support in exerting probiotic action by enabling adhesion to host epithelial cells and survival during antibiotic treatment and harsh conditions. PMID:27258038

Complete Genomes of Bacillus coagulans S-lac and Bacillus subtilis TO-A JPC, Two Phylogenetically Distinct Probiotics.

Directory of Open Access Journals (Sweden)

Indu Khatri

Full Text Available Several spore-forming strains of Bacillus are marketed as probiotics due to their ability to survive harsh gastrointestinal conditions and confer health benefits to the host. We report the complete genomes of two commercially available probiotics, Bacillus coagulans S-lac and Bacillus subtilis TO-A JPC, and compare them with the genomes of other Bacillus and Lactobacillus. The taxonomic position of both organisms was established with a maximum-likelihood tree based on twenty six housekeeping proteins. Analysis of all probiotic strains of Bacillus and Lactobacillus reveal that the essential sporulation proteins are conserved in all Bacillus probiotic strains while they are absent in Lactobacillus spp. We identified various antibiotic resistance, stress-related, and adhesion-related domains in these organisms, which likely provide support in exerting probiotic action by enabling adhesion to host epithelial cells and survival during antibiotic treatment and harsh conditions.

Continuous improvement of the regulatory framework for the control of medical exposure

International Nuclear Information System (INIS)

Larcher, Ana M.; Ortiz Lopez, Pedro; Arias, Cesar; Marechal, Maria H.; Hernandez Alvarez, Ramon; Ferrer Garcia, Natividad; Castaneda Mucino, Antonia; Faller, Blanca

2008-01-01

One of the key elements to guide the improvement of the regulatory control is the availability of a self-assessment tool for regulatory performance. Although there is general guidance on self-assessment for regulators and users (IAEA), there is a need for more specific advice on how to address challenges and difficulties faced by regulatory bodies, when regulating radiation protection of patients. Examples of these challenges are the need for regulatory initiatives, in cooperation with health and education authorities, professional bodies and equipment suppliers, and to put in place necessary elements that are beyond responsibility of individual user of radiation, to enable them compliance with safety standards. Purpose: Within the programme of the Ibero American Forum of Nuclear and Radiation Safety Regulatory Organizations, a project to develop such a self-assessment tool for the regulatory control of medical exposure has been designed. Method: National experiences in transposing and enforcing the international radiation safety standards, as to how the requirements are included in national regulations are reviewed. Further, difficulties to the implementation of safety requirements are analyzed and a self-assessment approach and possible regulatory solutions a are presented. Results and discussion: In this study the following documents are being produced: 1) transposition of international requirements into national regulations in the six countries of the Forum, 2) difficulties to implement and enforce the requirements, 3) guidance on self-assessment of regulatory framework for medical exposure, 4) suggested contribution to the revision of international radiation safety standards. (author)

7 CFR 1710.105 - State regulatory approvals.

Science.gov (United States)

2010-01-01

... and Basic Policies § 1710.105 State regulatory approvals. (a) In States where a borrower is required... loans are approved by RUS: (1) Loans requiring an Environmental Impact Statement; (2) Loans to finance...

Hydrogen mitigation systems - a Canadian regulatory perspective

International Nuclear Information System (INIS)

Khosla, J.K.; Rizk, M.

1997-01-01

This is a discussion paper to examine the regulatory requirements that may be necessary for the design, operation and maintenance of the hydrogen mitigation systems. These systems (if deemed necessary to maintain the containment function), may be considered to be a part of the containment systems. Therefore, these requirements are derived mostly from the AECB Regulatory Document R-7, which specifies the requirements for containment systems for CANDU nuclear power plants. Some additional requirements, which are specific to these systems have also been included. These requirements relate to a systematic examination of the hazards of hydrogen, the design basis for the mitigation systems, their functional and design requirements, analytical support to justify their selection, and operating and testing requirements. The requirements for severe accident have not yet been developed. It is, however, anticipated that the design of the hydrogen mitigation system would be such that future requirement can be accommodated. These requirements are intended for application to the new reactors in Canada. For the existing reactors, their application will be subjected to practicability. (author)

Regulatory Models and the Environment: Practice, Pitfalls, and Prospects

Energy Technology Data Exchange (ETDEWEB)

Holmes, K. John; Graham, Judith A.; McKone, Thomas; Whipple, Chris

2008-06-01

Computational models support environmental regulatory activities by providing the regulator an ability to evaluate available knowledge, assess alternative regulations, and provide a framework to assess compliance. But all models face inherent uncertainties, because human and natural systems are always more complex and heterogeneous than can be captured in a model. Here we provide a summary discussion of the activities, findings, and recommendations of the National Research Council's Committee on Regulatory Environmental Models, a committee funded by the US Environmental Protection Agency to provide guidance on the use of computational models in the regulatory process. Modeling is a difficult enterprise even outside of the potentially adversarial regulatory environment. The demands grow when the regulatory requirements for accountability, transparency, public accessibility, and technical rigor are added to the challenges. Moreover, models cannot be validated (declared true) but instead should be evaluated with regard to their suitability as tools to address a specific question. The committee concluded that these characteristics make evaluation of a regulatory model more complex than simply comparing measurement data with model results. Evaluation also must balance the need for a model to be accurate with the need for a model to be reproducible, transparent, and useful for the regulatory decision at hand. Meeting these needs requires model evaluation to be applied over the"life cycle" of a regulatory model with an approach that includes different forms of peer review, uncertainty analysis, and extrapolation methods than for non-regulatory models.

Regulatory facility guide for Ohio

Energy Technology Data Exchange (ETDEWEB)

Anderson, S.S.; Bock, R.E.; Francis, M.W.; Gove, R.M.; Johnson, P.E.; Kovac, F.M.; Mynatt, J.O. [Oak Ridge National Lab., TN (United States); Rymer, A.C. [Transportation Consulting Services, Knoxville, TN (United States)

1994-02-28

The Regulatory Facility Guide (RFG) has been developed for the DOE and contractor facilities located in the state of Ohio. It provides detailed compilations of international, federal, and state transportation-related regulations applicable to shipments originating at destined to Ohio facilities. This RFG was developed as an additional resource tool for use both by traffic managers who must ensure that transportation operations are in full compliance with all applicable regulatory requirements and by oversight personnel who must verify compliance activities.

Regulatory requirements related to risk-based inspection and maintenance

International Nuclear Information System (INIS)

Schroeder, H.C.; Kauer, R.

2003-01-01

By asking the question why new inspection and maintenance strategies have to be developed one can often be made aware that there is always a continue demand for cost reduction and optimisation. In this framework, general trends involving staff reduction, outsourcing, benchmarking etc. can often be observed nearly everywhere. Since inspection and maintenance are amongst the few cost factors, which could be actively influenced in the short term, and in combination with the recent regulatory fundamental changes (e.g. PED) yielding to considerably greater responsibilities for the operator of a plant, also the demand for documentation and comprehensibility of measures will increase. (orig.)

Current status of developmental neurotoxicity: regulatory view

DEFF Research Database (Denmark)

Hass, Ulla

2003-01-01

in the testing strategy for new and existing substances, and biocides. Hopefully, this will lead to an improved database for risk assessment of potential developmental neurotoxicants. However, the regulatory authorities and toxicologists will also be faced with the challenge that decisions have to be made......The need for developmental neurotoxicity testing has been recognized for decades and guidelines are available, as the USEPA guideline and the OECD draft TG 426. Regulatory testing of industrial chemicals for developmental neurotoxicity is required to some extent, especially for pesticides in the US....... Until recently, however, developmental neurotoxicity testing of industrial chemicals has not been a clear regulatory requirement in EU, probably due to the lack of an accepted OECD TG. The revised EU Technical Guidance Document for Risk Assessment (EU-TGD) has now included the OECD draft TG 426...

Comments on regulatory reform

Energy Technology Data Exchange (ETDEWEB)

Hendrie, J.M.

1982-01-01

Nuclear regulatory reform is divided into two parts. The first part contains all those matters for which new legislation is required. The second part concerns all those matters that are within the power of the Commission under existing statutes. Recommendations are presented.

Comments on regulatory reform

International Nuclear Information System (INIS)

Hendrie, J.M.

1982-01-01

Nuclear regulatory reform is divided into two parts. The first part contains all those matters for which new legislation is required. The second part concerns all those matters that are within the power of the Commission under existing statutes. Recommendations are presented

Design basis ground motion (Ss) required on new regulatory guide

International Nuclear Information System (INIS)

Kamae, Katsuhiro

2013-01-01

New regulatory guide is enforced on July 8. Here, it is introduced how the design basis ground motion (Ss) for seismic design of nuclear power reactor facilities was revised on the new guide. Ss is formulated as two types of earthquake ground motions, earthquake ground motions with site specific earthquake source and with no such specific source locations. The latter is going to be revised based on the recent observed near source ground motions. (author)

Perceptions of regulatory approaches

International Nuclear Information System (INIS)

Halin, Magnus; Leinonen, Ruusaliisa

2012-01-01

Ms. Ruusaliisa Leinonen and Mr. Magnus Halin from Fortum gave a joint presentation on industry perceptions of regulatory oversight of LMfS/SC. It was concluded that an open culture of discussion exists between the regulator (STUK) and the licensee, based on the common goal of nuclear safety. An example was provided of on how regulatory interventions helped foster improvements to individual and collective dose rate trends, which had remained static. Regulatory interventions included discussions on the ALARA concept to reinforce the requirement to continuously strive for improvements in safety performance. Safety culture has also been built into regulatory inspections in recent years. Training days have also been organised by the regulatory body to help develop a shared understanding of safety culture between licensee and regulatory personnel. Fortum has also developed their own training for managers and supervisors. Training and ongoing discussion on LMfS/SC safety culture is considered particularly important because both Fortum and the regulatory body are experiencing an influx of new staff due to the demographic profile of their organisations. It was noted that further work is needed to reach a common understanding of safety culture on a practical level (e.g., for a mechanic setting to work), and in relation to the inspection criteria used by the regulator. The challenges associated with companies with a mix of energy types were also discussed. This can make it more difficult to understand responsibilities and decision making processes, including the role of the parent body organisation. It also makes communication more challenging due to increased complexity and a larger number of stakeholders

Compliance. Regulatory policy P-211

International Nuclear Information System (INIS)

2001-05-01

This regulatory policy describes the basic principles and directives for establishing and conducting the Canadian Nuclear Safety Commission (CNSC) Compliance Program. The program is aimed at securing compliance by regulated persons with regulatory requirements made under the Nuclear Safety and Control Act ('the Act'). The policy applies to persons who are regulated by the CNSC through the Act, regulations and licences, as well as by decisions and orders made under the Act. The policy applies to officers and employees of the CNSC, and its authorized representatives or agents, who are involved in developing and carrying out compliance activities. Compliance, in the context of this policy, means conformity by regulated persons with the legally binding requirements of the Act, and the CNSC regulations, licences, decisions, and orders made under the Act. Compliance activities are CNSC measures of promotion, verification and enforcement aimed at securing compliance by regulated person with the applicable legally binding requirements. (author)

Situation of the medical physics in the Republic of Argentina. Regulatory problem linked to the requirement of physic specialists

International Nuclear Information System (INIS)

Arbor Gonzalez, A.; Larcher, A.; Blanco, S.

2001-01-01

This paper provides up-to-date data on the participation of medical physicists in current staffs for radiotherapy, nuclear medicine and diagnostic radiology in Argentina, and it presents projections on the academic education of specialists in the next five years. At the same time, the regulatory framework including the requirements for physicists staffing levels in medical practices is presented. This panorama permits to stick out the important role of the professional associations and the academic institutions in the development of Medical Physics in the country. (author)

Guidelines for IAEA International Regulatory Review Teams (IRRTs)

International Nuclear Information System (INIS)

2002-01-01

The IAEA International Regulatory Review Team (IRRT) programme provides advice and assistance to Member States to strengthen and enhance the effectiveness of the nuclear regulatory body whilst recognizing the ultimate responsibility of each Member State for nuclear safety. The IRRT programme, initiated in 1989, is not restricted to any particular group of Member States, whether developing or industrialized, but is available to all countries with nuclear installations in operation or approaching operation. The basic concepts, purposes and functions of a national regulatory body are well recognized in all Member States having a nuclear power programme. The IAEA Safety Standards Series publication entitled 'Legal and Governmental Infrastructure for Nuclear, Radiation, Radioactive Waste and Transport Safety, Safety: Requirements', No. GS-R-1 (2000), provides a general consensus reference for the practices necessary for a national organization to fulfil the regulatory purposes and discharge the regulatory functions. The Requirements also defines the terms used in these guidelines. The guidance given in the Requirements recognizes that the organizational structure and regulatory processes will vary from country to country depending on their existing constitutional, legal and administrative systems; the size and structure of their nuclear programme; the technical skills and professional and financial resources available to their regulatory body, and social customs and cultural traditions. The objective of this report is to provide guidance on the basic structure of an IRRT mission and provide a common reference both across the various areas covered by an IRRT mission and across all the missions in the programme. As such, it is addressed, principally, to the team members of IRRT missions but it also provides guidance to a host regulatory body receiving a mission. This report identifies the objectives of the IRRT mission and sets out the scope of the topic areas that are

Continuous Improvement of the Regulatory Framework for the Control of Medical Exposure

International Nuclear Information System (INIS)

Larcher, A.M.; Ortiz lopez, Pedro; Arias, Cesar; Marechal, Maria H.; Hernandez Alvarez, Ramon; Ferrer Garcia, Natividad; Castaneda Mucino, Antonia; Faller, Blanca

2011-01-01

Background: One of the key elements to guide the improvement of the regulatory control is the availability of a self-assessment tool for regulatory performance. Although there is general guidance on self-assessment for regulators and users (IAEA), there is a need for specific advice on how to address challenges and difficulties faced by regulatory bodies, when regulating radiation protection of patients. Examples of these challenges are the need of regulatory initiatives, in cooperation with health and education authorities, professional bodies and equipment suppliers, and to put in place necessary elements that are beyond responsibility of individual users of radiation, to enable them compliance with safety standards. Purpose: within the programme of the Ibero American Forum of Nuclear and Radiation Safety Regulatory Organizations, a project to develop such a self assessment tool for the regulatory control of medical exposure has been designed. Method: national experiences in transposing and enforcing the international radiation safety standards, as to how the requirements are included in national regulations are reviewed. Further, difficulties to the implementation of safety requirements are included in national regulations are analyzed and a self assessment approach and possible regulatory solutions are presented. Results and discussion: in tis study the following documents are being produced: 1) Transposition of international requirements into national regulations in the six countries of the Forum, 2) difficulties to implement and enforce the requirements, 3) guidance on self assessment of regulatory framework for medical exposure, 4) suggested contribution to the revision of international radiation safety standards. (authors)

Regulatory requirements on accident management and emergency preparedness - concept of nuclear and radiation safety during beyond-design-basis accidents

International Nuclear Information System (INIS)

Yanke, R.

2002-01-01

Actual practice the and proposals for further activities in the field of Accident Management (AM) in the member countries of the Co-operation Forum of WWER regulators and in Western countries have been assessed. Further the results of the last working group on AM , the overview of interactions of severe accident research and the regulatory positions in various countries, IAEA reports, practice in Switzerland and Finland, were taken into consideration. From this information, the working group derived recommendations on Accident Management. The general proposals correspond to the present state of the art on AM. They do not describe the whole spectra of recommendations on AM for NPPs with WWER reactors. A basis for the implementation of an AM program is given, which could be extended in a follow-up working group. The developments and research concerning AM have to be continued. The positions of various countries with regard to the 'Interactions of severe accident research and the regulatory positions' are given. On the basis of the working group proposals, the WWER regulators could set regulatory requirements and support further developments of AM strategies, making use of the benefits of common features of NPPs with WWER reactors. Concerted actions in the field of AM between the WWER regulators would bundle the development of a unified concept of recommendations and speed up the implementation of AM measures in order to minimise the risks involved in nuclear power generation

Regulatory requirements and administrative practice in safety of nuclear installations

International Nuclear Information System (INIS)

Servant, J.

1977-01-01

This paper reviews the current situation of the France regulatory rules and procedures dealing with the safety of the main nuclear facilities and, more broadly, the nuclear security. First, the author outlines the policy of the French administration which requires that the licensee responsible for an installation has to demonstrate that all possible measures are taken to ensure a sufficient level of safety, from the early stage of the project to the end of the operation of the plant. Thus, the administration performs the assessment on a case-by-case basis, of the safety of each installation before granting a nuclear license. On the other hand, the administration settles overall safety requirements for specific categories of installations or components, which determine the ultimate safety performances, but avoid, as far as possible, to detail the technical specifications to be applied in order to comply with these goals. This approach, which allows the designers and the licensees to rely upon sound codes and standards, gains the advantage of a great flexibility without imparing the nuclear safety. The author outlines the licensing progress for the main categories of installations: nuclear power plants of the PWR type, fast breeders, uranium isotope separation plants, and irradiated fuel processing plants. Emphasis is placed on the most noteworthy points: standardization of projects, specific risks of each site, problems of advanced type reactors, etc... The development of the technical regulations is presented with emphasis on the importance of an internationally concerned action within the nuclear international community. The second part of this paper describes the France operating experience of nuclear installations from the safety point of view. Especially, the author examines the technical and administrative utilization of data from safety significant incidents in reactors and plants, and the results of the control performed by the nuclear installations

Current status of herbal product: Regulatory overview

Science.gov (United States)

Sharma, Sanjay

2015-01-01

A review of the regulatory status of herbal drugs/products was done for few countries forming part of Asia, Africa, America, Europe, and Australia, to understand various categories under which the trade of herbal products is permitted and their premarketing requirements. A critical assessment was done, to know the hindrances in the process of harmonization of herbal products. It has been found that there is a lack of harmonization in the regulatory requirements of herbal products internationally, besides the issues of availability of herbs and their conservation. These are hindering the international trade and growth of the herbal products segment. PMID:26681886

Canadian uranium mines and mills evolution of regulatory expectations and requirements for effluent treatment

International Nuclear Information System (INIS)

LeClair, J.; Ashley, F.

2006-01-01

The regulation of uranium mining in Canada has changed over time as our understanding and concern for impacts on both human and non-human biota has evolved. Since the mid-1970s and early 1980s, new uranium mine and mill developments have been the subject of environmental assessments to assess and determine the significance of environmental effects throughout the project life cycle including the post-decommissioning phase. Water treatment systems have subsequently been improved to limit potential effects by reducing the concentration of radiological and non-radiological contaminants in the effluent discharge and the total loadings to the environment. This paper examines current regulatory requirements and expectations and how these impact uranium mining/milling practices. It also reviews current water management and effluent treatment practices and performance. Finally, it examines the issues and challenges for existing effluent treatment systems and identifies factors to be considered in optimizing current facilities and future facility designs. (author)

Common definition for categories of clinical research: a prerequisite for a survey on regulatory requirements by the European Clinical Research Infrastructures Network (ECRIN)

LENUS (Irish Health Repository)

Kubiak, Christine

2009-10-16

Abstract Background Thorough knowledge of the regulatory requirements is a challenging prerequisite for conducting multinational clinical studies in Europe given their complexity and heterogeneity in regulation and perception across the EU member states. Methods In order to summarise the current situation in relation to the wide spectrum of clinical research, the European Clinical Research Infrastructures Network (ECRIN) developed a multinational survey in ten European countries. However a lack of common classification framework for major categories of clinical research was identified, and therefore reaching an agreement on a common classification was the initial step in the development of the survey. Results The ECRIN transnational working group on regulation, composed of experts in the field of clinical research from ten European countries, defined seven major categories of clinical research that seem relevant from both the regulatory and the scientific points of view, and correspond to congruent definitions in all countries: clinical trials on medicinal products; clinical trials on medical devices; other therapeutic trials (including surgery trials, transplantation trials, transfusion trials, trials with cell therapy, etc.); diagnostic studies; clinical research on nutrition; other interventional clinical research (including trials in complementary and alternative medicine, trials with collection of blood or tissue samples, physiology studies, etc.); and epidemiology studies. Our classification was essential to develop a survey focused on protocol submission to ethics committees and competent authorities, procedures for amendments, requirements for sponsor and insurance, and adverse event reporting following five main phases: drafting, consensus, data collection, validation, and finalising. Conclusion The list of clinical research categories as used for the survey could serve as a contribution to the, much needed, task of harmonisation and simplification of the

Common definition for categories of clinical research: a prerequisite for a survey on regulatory requirements by the European Clinical Research Infrastructures Network (ECRIN

Directory of Open Access Journals (Sweden)

Sanz Nuria

2009-10-01

Full Text Available Abstract Background Thorough knowledge of the regulatory requirements is a challenging prerequisite for conducting multinational clinical studies in Europe given their complexity and heterogeneity in regulation and perception across the EU member states. Methods In order to summarise the current situation in relation to the wide spectrum of clinical research, the European Clinical Research Infrastructures Network (ECRIN developed a multinational survey in ten European countries. However a lack of common classification framework for major categories of clinical research was identified, and therefore reaching an agreement on a common classification was the initial step in the development of the survey. Results The ECRIN transnational working group on regulation, composed of experts in the field of clinical research from ten European countries, defined seven major categories of clinical research that seem relevant from both the regulatory and the scientific points of view, and correspond to congruent definitions in all countries: clinical trials on medicinal products; clinical trials on medical devices; other therapeutic trials (including surgery trials, transplantation trials, transfusion trials, trials with cell therapy, etc.; diagnostic studies; clinical research on nutrition; other interventional clinical research (including trials in complementary and alternative medicine, trials with collection of blood or tissue samples, physiology studies, etc.; and epidemiology studies. Our classification was essential to develop a survey focused on protocol submission to ethics committees and competent authorities, procedures for amendments, requirements for sponsor and insurance, and adverse event reporting following five main phases: drafting, consensus, data collection, validation, and finalising. Conclusion The list of clinical research categories as used for the survey could serve as a contribution to the, much needed, task of harmonisation and

17 CFR 201.420 - Appeal of determinations by self-regulatory organizations.

Science.gov (United States)

2010-04-01

... self-regulatory organizations. 201.420 Section 201.420 Commodity and Securities Exchanges SECURITIES... Review § 201.420 Appeal of determinations by self-regulatory organizations. (a) Application for review... by a self-regulatory organization determination as to which a notice is required to be filed with the...

47 CFR 1.1159 - Filing locations and receipts for regulatory fees.

Science.gov (United States)

2010-10-01

... fees. 1.1159 Section 1.1159 Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL PRACTICE AND... for regulatory fees. (a) Regulatory fee payments must be directed to the location and address set forth in §§ 1.1152 through 1.1156 for the specific category of fee involved. Any regulatory fee required...

Regulatory Risk Management of Advanced Nuclear Power Plants

International Nuclear Information System (INIS)

George, Glenn R.

2002-01-01

Regulatory risk reflects both the likelihood of adverse outcomes during regulatory interactions and the severity of those outcomes. In the arena of advanced nuclear power plant licensing and construction, such adverse outcomes may include, for example, required design changes and construction delays. These, in turn, could significantly affect the economics of the plant and the generation portfolio in which it will operate. In this paper, the author addresses these issues through the lens of risk management. The paper considers various tools and techniques of regulatory risk management, including design diversity and hedging strategies. The effectiveness of alternate approaches is weighed and recommendations are made in several regulatory contexts. (author)

Cost-benefit considerations in regulatory decision-making

International Nuclear Information System (INIS)

Harvie, J.D.

1996-01-01

The Atomic Energy Control Board is investigating the feasibility of developing methods for factoring cost-benefit considerations into its regulatory decision-making. This initiative results, in part, from the federal government policy requiring cost-benefit considerations to be taken into account in regulatory processes, and from the recommendations of an Advisory Panel on Regulatory Review in 1993, submitted to the Minister of Natural Resources Canada. One of these recommendations stated: 'that mechanisms be developed to examine cost-benefit issues and work towards some consensus of opinion among stakeholders; a task force on the subject could be an appropriate starting point'. (author)

Impact of regulatory science on global public health

Directory of Open Access Journals (Sweden)

Meghal Patel

2012-07-01

Full Text Available Regulatory science plays a vital role in protecting and promoting global public health by providing the scientific basis for ensuring that food and medical products are safe, properly labeled, and effective. Regulatory science research was first developed for the determination of product safety in the early part of the 20th Century, and continues to support innovation of the processes needed for regulatory policy decisions. Historically, public health laws and regulations were enacted following public health tragedies, and often the research tools and techniques required to execute these laws lagged behind the public health needs. Throughout history, similar public health problems relating to food and pharmaceutical products have occurred in countries around the world, and have usually led to the development of equivalent solutions. For example, most countries require a demonstration of pharmaceutical safety and efficacy prior to marketing these products using approaches that are similar to those initiated in the United States. The globalization of food and medical products has created a shift in regulatory compliance such that gaps in food and medical product safety can generate international problems. Improvements in regulatory research can advance the regulatory paradigm toward a more preventative, proactive framework. These improvements will advance at a greater pace with international collaboration by providing additional resources and new perspectives for approaching and anticipating public health problems. The following is a review of how past public health disasters have shaped the current regulatory landscape, and where innovation can facilitate the shift from reactive policies to proactive policies.

Impact of regulatory science on global public health.

Science.gov (United States)

Patel, Meghal; Miller, Margaret Ann

2012-07-01

Regulatory science plays a vital role in protecting and promoting global public health by providing the scientific basis for ensuring that food and medical products are safe, properly labeled, and effective. Regulatory science research was first developed for the determination of product safety in the early part of the 20th Century, and continues to support innovation of the processes needed for regulatory policy decisions. Historically, public health laws and regulations were enacted following public health tragedies, and often the research tools and techniques required to execute these laws lagged behind the public health needs. Throughout history, similar public health problems relating to food and pharmaceutical products have occurred in countries around the world, and have usually led to the development of equivalent solutions. For example, most countries require a demonstration of pharmaceutical safety and efficacy prior to marketing these products using approaches that are similar to those initiated in the United States. The globalization of food and medical products has created a shift in regulatory compliance such that gaps in food and medical product safety can generate international problems. Improvements in regulatory research can advance the regulatory paradigm toward a more preventative, proactive framework. These improvements will advance at a greater pace with international collaboration by providing additional resources and new perspectives for approaching and anticipating public health problems. The following is a review of how past public health disasters have shaped the current regulatory landscape, and where innovation can facilitate the shift from reactive policies to proactive policies. Copyright © 2012. Published by Elsevier B.V.

ATMPs for Cancer Immunotherapy: A Regulatory Overview.

Science.gov (United States)

Galli, Maria Cristina

2016-01-01

This chapter discusses European regulatory requirements for development of advanced therapy medicinal products (ATMP) for cancer immunotherapy approaches, describing the framework for clinical trials and for marketing authorization.Regulatory critical issues and challenges for developing ATMP are also discussed, with focus on potency determination, long-term follow-up, comparability, and insertional mutagenesis issues. Some of the most critical features of GMP application to ATMP are also described.

The NE11 experiment at SLAC and the neutron form factors

International Nuclear Information System (INIS)

Stuart, L.M.; Lung, A.; Bosted, P.E.

1993-05-01

The neutron electromagnetic form factors G En and G Mn , which reflect the charge and magnetization distributions within the neutron, are of fundamental importance for understanding nucleon structure, and are necessary for calculations of processes involving the electromagnetic interaction with complex nuclei. These quantities are functions of Q 2 , the four-momentum transfer squared. SLAC experiment NE11 has measured these form factors out to a Q 2 of 4.0 (GeV/c) 2 with high precision, and the results have been recently published. This paper provides some additional details on the extraction of G Mn and G En from the NE11 measurements. Several formalisms have been developed over the years which attempt to understand the nucleon form factors using basic physical principles. Vector Meson Dominance (VMD) models are based on superpositions of photon couplings to various vector mesons. These models generally involve free parameters which are fit to form factor data at low Q 2 , and are not expected to be valid at high Q 2 . For asymptotically large Q 2 , dimensional scaling methods and perturbative Quantum Chromodynamics (pQCD) predict form factor behavior at large Q 2 , but they do not make absolute magnitude predictions. To describe the form factor behavior at intermediate values of Q 2 , a hybrid model by Gari and Kruempelmann (GK) uses VMD constraints at low Q 2 and pQCD constraints at high Q 2 . Free parameters in the model are adjusted to fit existing form factor data. Other approaches include the use of QCD sum rules to make absolute predictions, diquark models, and relativistic constituent quark models

Development of an integrated circuit VLSI used for time measurement and selective read out in the front end electronics of the DIRC for the Babar experience at SLAC; Developpement d'un circuit integre VLSI assurant mesure de temps et lecture selective dans l'electronique frontale du compteur DIRC de l'experience babar a slac

Energy Technology Data Exchange (ETDEWEB)

Zhang, B

1999-07-01

This thesis deals with the design the development and the tests of an integrated circuit VLSI, supplying selective read and time measure for 16 channels. This circuit has been developed for a experiment of particles physics, BABAR, that will take place at SLAC (Stanford Linear Accelerator Center). A first part describes the physical stakes of the experiment, the electronic architecture and the place of the developed circuit in the research program. The second part presents the technical drawings of the circuit, the prototypes leading to the final design and the validity tests. (A.L.B.)

Licensing and regulatory control of nuclear power plants in Canada

International Nuclear Information System (INIS)

Atchison, R.J.

1975-01-01

The paper discusses the safety philosophy adopted in Canada, the safety criteria and regulatory requirements necessary for the application of this philosophy to reactor design and operation, and finally the means by which compliance with Board requirements is effected. It is emphasized that the effectiveness of regulatory control depends not only on the underlying philosophy but also on the detailed way in which it is applied. (orig./HP) [de

Regulatory issues of digital instrumentation and control system in Lungmen project

International Nuclear Information System (INIS)

Chuang, C.F.; Chou, H.P.

2004-01-01

The Lungmen Nuclear Power Station (LNPS) is currently under construction in Taiwan, which consists of 2 advanced boiling water reactor (ABWR) units. The instrumentation and control (IC) systems of the LNPS are based on the state-of-the-art modernized fully integrated digital design. These IC systems possess many advantages and distinguished features comparing to traditional analog IC systems, they enjoy set-point stability, self-diagnostic and automatic testing ability, fault tolerance and avoidance, low power requirements, data handling and storage capability, as well as enhanced human-machine interfaces. This paper presents regulatory overviews, regulatory requirements, current major regulatory issues, as well as the areas of regulatory concerns and the lessons learned on the digital IC systems in the Lungmen Project

Regulatory pathways for vaccines for developing countries.

Science.gov (United States)

Milstien, Julie; Belgharbi, Lahouari

2004-01-01

Vaccines that are designed for use only in developing countries face regulatory hurdles that may restrict their use. There are two primary reasons for this: most regulatory authorities are set up to address regulation of products for use only within their jurisdictions and regulatory authorities in developing countries traditionally have been considered weak. Some options for regulatory pathways for such products have been identified: licensing in the country of manufacture, file review by the European Medicines Evaluation Agency on behalf of WHO, export to a country with a competent national regulatory authority (NRA) that could handle all regulatory functions for the developing country market, shared manufacturing and licensing in a developing country with competent manufacturing and regulatory capacity, and use of a contracted independent entity for global regulatory approval. These options have been evaluated on the basis of five criteria: assurance of all regulatory functions for the life of the product, appropriateness of epidemiological assessment, applicability to products no longer used in the domestic market of the manufacturing country, reduction of regulatory risk for the manufacturer, and existing rules and regulations for implementation. No one option satisfies all criteria. For all options, national infrastructures (including the underlying regulatory legislative framework, particularly to formulate and implement local evidence-based vaccine policy) must be developed. WHO has led work to develop this capacity with some success. The paper outlines additional areas of action required by the international community to assure development and use of vaccines needed for the developing world. PMID:15042235

Regulatory and licensee surveys

International Nuclear Information System (INIS)

2009-01-01

Prior to the workshop two CSNI/WGHOF surveys were distributed. One survey was directed at regulatory bodies and the other was directed at plant licensees. The surveys were: 1 - Regulatory Expectations of Licensees' Arrangements to Ensure Suitable Organisational Structure, Resources and Competencies to Manage Safety (sent to WGHOF regulatory members). The survey requested that the respondents provide a brief overview of the situation related to plant organisations in their country, their regulatory expectations and their formal requirements. The survey addressed three subjects: the demonstration and documentation of organisational structures, resources and competencies, organisational changes, issues for improvement (for both current and new plants). Responses were received from eleven regulatory bodies. 2 - Approaches to Justify Organisational Suitability (sent to selected licensees). The purpose of the survey to was to gain an understanding of how licensees ensure organisational suitability, resources and competencies. This information was used to assist in the development of the issues and subjects that were addressed at the group discussion sessions. Responses were received from over fifteen licensees from nine countries. The survey requested that the licensees provide information on how they ensure effective organisational structures at their plants. The survey grouped the questions into the following four categories: organisational safety functions, resource and competence, decision-making and communication, good examples and improvement needs. The findings from these surveys were used in conjunction with other factors to identify the key issues for the workshop discussion sessions. The responses from these two surveys are discussed briefly in Sections 4 and 5 of this report. More extensive reviews of the regulatory and licensee responses are provided in Appendix 1

Systematic Assessment of Regulatory Competences (SARCON) V18a

International Nuclear Information System (INIS)

Zimmermann, Moritz

2014-01-01

Why Competence Management? • Arrangements for competence management is a key factor to: • Support the implementation of article 8 of CNS (Convention on Nuclear Safety – “regulatory body with adequate competence and human resources”); • Support the implementation of Modules 3 and 4 of the IRRS and other IAEA Safety Standards (Module 3: “Responsibilities and functions of the regulatory body”, Module 4: “Management system of the regulatory body”); • Identify gaps between regulatory required competences and the existing resources; • Develop and implement tools and programmes to fill the gaps; • Review periodically the competence needs and training programmes

As to achieve regulatory action, regulatory approaches

International Nuclear Information System (INIS)

Cid, R.; Encinas, D.

2014-01-01

The achievement of the effectiveness in the performance of a nuclear regulatory body has been a permanent challenge in the recent history of nuclear regulation. In the post-Fukushima era this challenge is even more important. This article addresses the subject from two complementary points of view: the characteristics of an effective regulatory body and the regulatory approaches. This work is based on the most recent studies carried out by the Committee on Nuclear Regulatory Activities, CNRA (OECD/NEA), as well as on the experience of the Consejo de Seguridad Nuclear, CSN, the Spanish regulatory body. Rafael Cid is the representative of CSN in these project: Diego Encinas has participated in the study on regulatory approaches. (Author)

ENSI’s regulatory framework strategy; Regelwerksstrategie des ENSI -- Stratégie réglementaire de l’IFSN -- ENSI’s regulatory framework strategy

Energy Technology Data Exchange (ETDEWEB)

NONE

2015-03-15

This short brochure issued by the Swiss Federal Nuclear Safety Inspectorate ENSI defines the organisation’s regulatory framework strategy. Six guiding principles are declared and discussed: Comprehensive harmonisation with relevant international requirements, basing the regulatory framework on existing, tried-and-tested regulations, issuing of its own guidelines only when it is necessary to do so, guidelines to be drawn up transparently and with the involvement of all stakeholders and basing the level of detail of its regulatory framework on hazard potential and risk.

Safeguards inventory and process monitoring regulatory comparison

Energy Technology Data Exchange (ETDEWEB)

Cavaluzzi, Jack M. [Texas A & M Univ., College Station, TX (United States); Gibbs, Philip W. [Brookhaven National Lab. (BNL), Upton, NY (United States)

2013-06-27

Detecting the theft or diversion of the relatively small amount of fissile material needed to make a nuclear weapon given the normal operating capacity of many of today’s running nuclear production facilities is a difficult task. As throughput increases, the ability of the Material Control and Accountability (MC&A) Program to detect the material loss decreases because the statistical measurement uncertainty also increases. The challenge faced is the ability of current accounting, measurement, and material control programs to detect small yet significant losses under some regulatory approaches can decrease to the point where it is extremely low if not practically non-existent at normal operating capacities. Adding concern to this topic is that there are variations among regulatory bodies as far as what is considered a Significant Quantity (SQ). Some research suggests that thresholds should be lower than those found in any current regulation which if adopted would make meeting detection goals even more difficult. This paper reviews and compares the current regulatory requirements for the MA elements related to physical inventory, uncertainty of the Inventory Difference (ID), and Process Monitoring (PM) in the United States Department of Energy (DOE) and Nuclear Regulatory Commission (NRC), Rosatom of the Russian Federation and the Chinese Atomic Energy Agency (CAEA) of China. The comparison looks at how the regulatory requirements for the implementation of various MA elements perform across a range of operating capacities in example facilities.

Regulatory Control of Radiation Sources. Safety Guide (Arabic Edition)

International Nuclear Information System (INIS)

2012-01-01

This Safety Guide is intended to assist States in implementing the requirements established in Safety Standards Series No. GS-R-1, Legal and Governmental Infrastructure for Nuclear, Radiation, Radioactive Waste and Transport Safety, for a national regulatory infrastructure to regulate any practice involving radiation sources in medicine, industry, research, agriculture and education. The Safety Guide provides advice on the legislative basis for establishing regulatory bodies, including the effective independence of the regulatory body. It also provides guidance on implementing the functions and activities of regulatory bodies: the development of regulations and guides on radiation safety; implementation of a system for notification and authorization; carrying out regulatory inspections; taking necessary enforcement actions; and investigating accidents and circumstances potentially giving rise to accidents. The various aspects relating to the regulatory control of consumer products are explained, including justification, optimization of exposure, safety assessment and authorization. Guidance is also provided on the organization and staffing of regulatory bodies. Contents: 1. Introduction; 2. Legal framework for a regulatory infrastructure; 3. Principal functions and activities of the regulatory body; 4. Regulatory control of the supply of consumer products; 5. Functions of the regulatory body shared with other governmental agencies; 6. Organization and staffing of the regulatory body; 7. Documentation of the functions and activities of the regulatory body; 8. Support services; 9. Quality management for the regulatory system.

Semaphorin 4C Protects against Allergic Inflammation: Requirement of Regulatory CD138+ Plasma Cells.

Science.gov (United States)

Xue, Di; Kaufman, Gabriel N; Dembele, Marieme; Beland, Marianne; Massoud, Amir H; Mindt, Barbara C; Fiter, Ryan; Fixman, Elizabeth D; Martin, James G; Friedel, Roland H; Divangahi, Maziar; Fritz, Jörg H; Mazer, Bruce D

2017-01-01

The regulatory properties of B cells have been studied in autoimmune diseases; however, their role in allergic diseases is poorly understood. We demonstrate that Semaphorin 4C (Sema4C), an axonal guidance molecule, plays a crucial role in B cell regulatory function. Mice deficient in Sema4C exhibited increased airway inflammation after allergen exposure, with massive eosinophilic lung infiltrates and increased Th2 cytokines. This phenotype was reproduced by mixed bone marrow chimeric mice with Sema4C deficient only in B cells, indicating that B lymphocytes were the key cells affected by the absence of Sema4C expression in allergic inflammation. We determined that Sema4C-deficient CD19 + CD138 + cells exhibited decreased IL-10 and increased IL-4 expression in vivo and in vitro. Adoptive transfer of Sema4c -/- CD19 + CD138 + cells induced marked pulmonary inflammation, eosinophilia, and increased bronchoalveolar lavage fluid IL-4 and IL-5, whereas adoptive transfer of wild-type CD19 + CD138 + IL-10 + cells dramatically decreased allergic airway inflammation in wild-type and Sema4c -/- mice. This study identifies a novel pathway by which Th2-mediated immune responses are regulated. It highlights the importance of plasma cells as regulatory cells in allergic inflammation and suggests that CD138 + B cells contribute to cytokine balance and are important for maintenance of immune homeostasis in allergic airways disease. Furthermore, we demonstrate that Sema4C is critical for optimal regulatory cytokine production in CD138 + B cells. Copyright © 2016 by The American Association of Immunologists, Inc.

Measuring and Modeling the U.S. Regulatory Ecosystem

Science.gov (United States)

Bommarito, Michael J., II; Katz, Daniel Martin

2017-09-01

Over the last 23 years, the U.S. Securities and Exchange Commission has required over 34,000 companies to file over 165,000 annual reports. These reports, the so-called "Form 10-Ks," contain a characterization of a company's financial performance and its risks, including the regulatory environment in which a company operates. In this paper, we analyze over 4.5 million references to U.S. Federal Acts and Agencies contained within these reports to measure the regulatory ecosystem, in which companies are organisms inhabiting a regulatory environment. While individuals across the political, economic, and academic world frequently refer to trends in this regulatory ecosystem, far less attention has been paid to supporting such claims with large-scale, longitudinal data. In this paper, in addition to positing a model of regulatory ecosystems, we document an increase in the regulatory energy per filing, i.e., a warming "temperature." We also find that the diversity of the regulatory ecosystem has been increasing over the past two decades. These findings support the claim that regulatory activity and complexity are increasing, and this framework contributes an important step towards improving academic and policy discussions around legal complexity and regulation.

Second generation SLAC modulator

International Nuclear Information System (INIS)

Donaldson, A.R.; Cron, J.C.; Hanselman, R.R.

1986-06-01

The Stanford Linear Accelerator Laboratory has undertaken the construction of a single pass electron-positron collider. In order to reach required beam energy 235 new klystrons needed upgraded modulator systems. The collider will use 50 GeV electrons and positrons. The increase in accelerator energy from the present 30 GeV necessitates the replacement of existing 35 MW klystrons with new 67 MW units. The doubling of klystron output power required a redesign of the modulator system. The 67 MW klystron needs a 350 kV beam voltage pulse with a 3.7 μs pulse width. A new pulse transformer was designed to deliver the increased voltage and pulse width. Pulse cable design was evaluated to obtain increased reliability of that critical element. The modulator, with the exception of its power supply, was rebuilt to produce the required power increase while enhancing reliability and improving maintainability. An investigation of present thyratron switch tube performance under the new operating conditions resulted in agitation and some warranted panic but these conditions were mitigated after several successful experiments and some evolutionary narrowing of the klystron pulse width. The discussion will cover the upgraded modulator system specifications and some details of the new pulse transformer tank, pulse cable, modulator, and modulator switch tube

Glycoconjugate Vaccines: The Regulatory Framework.

Science.gov (United States)

Jones, Christopher

2015-01-01

Most vaccines, including the currently available glycoconjugate vaccines, are administered to healthy infants, to prevent future disease. The safety of a prospective vaccine is a key prerequisite for approval. Undesired side effects would not only have the potential to damage the individual infant but also lead to a loss of confidence in the respective vaccine-or vaccines in general-on a population level. Thus, regulatory requirements, particularly with regard to safety, are extremely rigorous. This chapter highlights regulatory aspects on carbohydrate-based vaccines with an emphasis on analytical approaches to ensure the consistent quality of successive manufacturing lots.

Regulatory control of nuclear power plants

International Nuclear Information System (INIS)

2002-01-01

consultants meeting at the end of 2001 by adding updates on the Nuclear Safety Convention and US regulatory practices. The main purpose of the book is to provide written background material to the participants and to support lecturers of the training courses on Regulatory Control of Nuclear Power Plants. The idea is to present general practices recommended by the IAEA in its safety guidance as well as country specific examples of how these general principles and requirements have been implemented in various countries. The examples selected are representative, showing existing and functional practices, and also provide a good selection of different practices adopted by different regulatory organizations. They reflect practices in large and small countries and regulatory bodies. They do not follow any particular regulatory practice but try to offer several alternatives to be useful for many inspectors coming from different types of organizations. The textbook has been compiled from the presentations provided during the training courses on Regulatory Control of Nuclear Power Plants from 1997 to 2001

Improving regulatory oversight of maintenance programs

International Nuclear Information System (INIS)

Cook, S.

2008-01-01

Safe nuclear power plant operation requires that risks due to failure or unavailability of Structures, Systems and Components (SSCs) be minimized. Implementation of an effective maintenance program is a key means for achieving this goal. In its regulatory framework, the important relationship between maintenance and safety is acknowledged by the CNSC. A high level maintenance program requirement is included in the Class I Facilities Regulations. In addition, the operating licence contains a condition based on the principle that the design function and performance of SSCs needs to remain consistent with the plant's design and analysis documents. Nuclear power plant licensees have the primary responsibility for safe operation of their facilities and consequently for implementation of a successful maintenance program. The oversight role of the Canadian Nuclear Safety Commission (CNSC) is to ensure that the licensee carries out that responsibility. The challenge for the CNSC is how to do this consistently and efficiently. Three opportunities for improvement to regulatory maintenance oversight are being pursued. These are related to the regulatory framework, compliance verification inspection activities and monitoring of self-reporting. The regulatory framework has been improved by clarifying expectations through the issuance of S-210 'Maintenance Programs for Nuclear Power Plants'. Inspection activities have been improved by introducing new maintenance inspections into the baseline program. Monitoring is being improved by making better use of self-reported and industry produced maintenance related performance indicators. As with any type of program change, the challenge is to ensure the consistent and optimal application of regulatory activities and resources. This paper is a summary of the CNSC's approach to improving its maintenance oversight strategy. (author)

75 FR 54921 - Withdrawal of Regulatory Guides 1.38, 1.94, and 1.116

Science.gov (United States)

2010-09-09

... Guide 1.38, ``Quality Assurance Requirements for Packaging, Shipping, Receiving, Storage, and Handling....116, ``Quality Assurance Requirements for Installation, Inspection, and Testing of Mechanical... Development Branch, Division of Engineering, Office of Nuclear Regulatory Research, U.S. Nuclear Regulatory...

Regulatory and Non-regulatory Responses to Hydraulic Fracturing in Local Communities

Science.gov (United States)

Phartiyal, P.

2015-12-01

The practice of extracting oil and gas from tight rock formations using advances in technology, such as hydraulic fracturing and directional drilling, has expanded exponentially in states and localities across the country. As the scientific data collection and analysis catches up on the many potential impacts of this unconventional oil and gas development, communities are turning to their local officials to make decisions on whether and how fracking should proceed. While most regulatory authority on the issue rests with the state agencies, local officials have experimented with a wide range of regulatory, non-regulatory, and fiscal tools to manage the impacts of fracking. These impacts can occur on the local air, water, seismicity, soil, roads, schools, and affect residents, on-site workers, emergency and social services. Local officials' approaches are often influenced by their prior experience with minerals extraction in their localities. The speaker will present examples of the kinds of information sources, tools and approaches communities across the country are using, from noise barriers to setback requirements to information sharing in order to be able to balance the promise and perils of oil and gas development in their jurisdictions.

Enabling legislation and regulatory determinations for a nuclear power programme

International Nuclear Information System (INIS)

Ha-Vinh, Phuong

1975-01-01

Broad definition of the scope of enabling legislation, identification of branches of laws involved in the licensing and regulatory control, overview of some typical licensing practices and provisions, some specific legislative or regulatory requirements including financial security to over nuclear liability. (HP) [de

Strengthening Regulatory Competence in Pakistan

International Nuclear Information System (INIS)

Sadiq, M.

2016-01-01

Capacity building of Pakistan Nuclear Regulatory Authority is considered an essential element in pursuit of its vision to become a world class regulatory body. Since its inception in 2001, PNRA has continuously endeavoured to invest in its people, develop training infrastructure and impart sound knowledge and professional skills with the aim to improve its regulatory effectiveness. The use of nuclear and radioactive material in Pakistan has increased manifold in recent years, thus induction of more manpower was needed for regulatory oversight. PNRA adopted two pronged approach for meeting the manpower demand (a) employment of university graduates through fast track recruitment drive and (b) induction of graduates by offering fellowships for Master degree programs. Although, the newly employed staff was selected on the basis of their excellent academic qualifications in basic and applied sciences, but they required rigorous knowledge and skills in regulatory perspectives. In order to implement a structured training program, PNRA conducted Training Needs Assessment (TNA) and identified competency gaps of the regulatory staff in legal, technical, regulatory practice and behavioural domains. PNRA took several initiatives for capacity building which included establishment of a training centre for sustainability of trainings, initiation of a fellowship scheme for Master program, attachment of staff at local institutes for on-the-job training and placement at foreign regulatory bodies and organizations for technical development with the assistance of IAEA. The above strategies have been very beneficial in competence building of the PNRA staff to perform all regulatory activities indigenously for nuclear power plants, research reactors and radiation facilities. Provision of vibrant technical support to IAEA and Member States in various programs by PNRA is a landmark of these competence development efforts. This paper summarizes PNRA initiatives and the International Atomic

A guide to ventilation requirements for uranium mines and mills. Regulatory guide G-221

International Nuclear Information System (INIS)

2003-06-01

The purpose of G-221 is to help persons address the requirements for the submission of ventilation-related information when applying for a Canadian Nuclear Safety Commission (CNSC) licence to site and construct, operate or decommission a uranium mine or mill. This guide is also intended to help applicants for a uranium mine or mill licence understand their operational and maintenance obligations with respect to ventilation systems, and to help CNSC staff evaluate the adequacy of applications for uranium mine and mill licences. This guide is relevant to any application for a CNSC licence to prepare a site for and construct, operate or decommission a uranium mine or mill. In addition to summarizing the ventilation-related obligations or uranium mine and mill licensee, the guide describes and discusses the ventilation-related information that licence applicants should typically submit to meet regulatory requirements. The guide pertains to any ventilation of uranium mines and mills for the purpose of assuring the radiation safety of workers and on-site personnel. This ventilation may be associated with any underground or surface area or premise that is licensable by the CNSC as part of a uranium mine or mill. These areas and premises typically include mine workings, mill buildings, and other areas or premises involving or potentially affected by radiation or radioactive materials. Some examples of the latter include offices, effluent treatment plants, cafeterias, lunch rooms and personnel change-rooms. (author)

Reliability programs for nuclear power plants. Regulatory standard S-98 revision 1

International Nuclear Information System (INIS)

2005-07-01

The purpose of this regulatory standard is to help assure, in accordance with the purpose of the Nuclear Safety and Control Act (NSCA), that a licensee who constructs or operates a nuclear power plant (NPP) develops and implements a reliability program that assures that the systems important to safety at the plant can and will meet their defined design and performance specifications at acceptable levels of reliability throughout the lifetime of the facility. This regulatory standard describes the requirements of a reliability program for a nuclear power plant. The licensee shall implement the requirements described in this regulatory standard when a condition of a licence or other legally enforceable instrument so requires.(author)

Regulatory viewpoint on nuclear fuel quality assurance

International Nuclear Information System (INIS)

Tripp, L.E.

1976-01-01

Considerations of the importance of fuel quality and performance to nuclear safety, ''as low reasonably achievable'' release of radioactive materials in reactor effluents, and past fuel performance problems demonstrate the need for strong regulatory input, review and inspection of nuclear fuel quality assurance programs at all levels. Such a regulatory program is being applied in the United States of America by the US Nuclear Regulatory Commission. Quality assurance requirements are contained within government regulations. Guidance on acceptable methods of implementing portions of the quality assurance program is contained within Regulatory Guides and other NRC documents. Fuel supplier quality assurance program descriptions are reviewed as a part of the reactor licensing process. Inspections of reactor licensee control of their fuel vendors as well as direct inspections of fuel vendor quality assurance programs are conducted on a regularly scheduled basis. (author)

Regulatory practices of radiation safety of SNF transportation in Russia

International Nuclear Information System (INIS)

Kuryndina, Lidia; Kuryndin, Anton; Stroganov, Anatoly

2008-01-01

This paper overviews current regulatory practices for the assurance of nuclear and radiation safety during railway transportation of SNF on the territory of Russian Federation from NPPs to longterm-storage of reprocessing sites. The legal and regulatory requirements (mostly compliant with IAEA ST-1), licensing procedure for NM transportation are discussed. The current procedure does not require a regulatory approval for each particular shipment if the SNF fully comply with the Rosatom's branch standard and is transported in approved casks. It has been demonstrated that SNF packages compliant with the branch standard, which is knowingly provide sufficient safety margin, will conform to the federal level regulations. The regulatory approval is required if a particular shipment does not comply with the branch standard. In this case, the shipment can be approved only after regulatory review of Applicant's documents to demonstrate that the shipment still conformant to the higher level (federal) regulations. The regulatory review frequently needs a full calculation test of the radiation safety assurance. This test can take a lot of time. That's why the special calculation tools were created in SEC NRS. These tools aimed for precision calculation of the radiation safety parameters by SNF transportation use preliminary calculated Green's functions. Such approach allows quickly simulate any source distribution and optimize spent fuel assemblies placement in cask due to the transport equation property of linearity relatively the source. The short description of calculation tools are presented. Also, the paper discusses foreseen implications related to transportation of mixed-oxide SNF. (author)

76 FR 78059 - Self-Regulatory Organizations; Options Clearing Corporation; Order Approving Proposed Rule Change...

Science.gov (United States)

2011-12-15

... SECURITIES AND EXCHANGE COMMISSION [Release No. 34-65927; File No. SR-OCC-2011-15] Self-Regulatory Organizations; Options Clearing Corporation; Order Approving Proposed Rule Change Relating to Management of..., future regulatory requirements for clearinghouses could impose liquidity requirements that would be...

Radiation safety in educational, medical and research institutions. Regulatory guide G-121

International Nuclear Information System (INIS)

2000-05-01

This regulatory guide is intended to help educational, medical and research institutions design and implement radiation protection programs that meed regulatory requirements. This guide applied to educational, medical or research institutions that require a licence from the CNSC to posses or use radioactive materials. It describes programs to assure that radioactive materials are used safely during licensed activities. (author)

77 FR 40817 - Low-Level Radioactive Waste Regulatory Management Issues

Science.gov (United States)

2012-07-11

...-2011-0012] RIN-3150-AI92 Low-Level Radioactive Waste Regulatory Management Issues AGENCY: Nuclear... regulatory time of compliance for a low-level radioactive waste disposal facility, allowing licensees the... system, and revising the NRC's licensing requirements for land disposal of radioactive waste. DATES: The...

South African Regulatory Framework for Nuclear Power Plant Life Management

International Nuclear Information System (INIS)

Mbebe, B.Z.

2012-01-01

The paper presents the regulatory approach to plant life management (PLiM) adopted by the National Nuclear Regulator (NNR) in South Africa, the licensing basis and regulatory requirements for Koeberg Nuclear Power Station (KNPS),operational programmes ensuring continued safe operation, issues related to the ageing of the plant, and the requirements for spent fuel as well as radioactive waste management. The paper will further present insights from the Periodic Safety Review (PSR) and Long Term Asset Management. (author)

Advanced Reactor Technologies - Regulatory Technology Development Plan (RTDP)

Energy Technology Data Exchange (ETDEWEB)

Moe, Wayne L. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2017-08-23

importance of key DOE reactor research initiatives should be assessed early in the technology development process. Quality assurance requirements supportive of later licensing activities must also be attached to important research activities to ensure resulting data is usable in that context. Early regulatory analysis and licensing approach planning thus provides a significant benefit to the formulation of research plans and also enables the planning and development of a compatible AdvSMR licensing framework, should significant modification be required.

Advanced Reactor Technology -- Regulatory Technology Development Plan (RTDP)

Energy Technology Data Exchange (ETDEWEB)

Moe, Wayne Leland [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-05-01

importance of key DOE reactor research initiatives should be assessed early in the technology development process. Quality assurance requirements supportive of later licensing activities must also be attached to important research activities to ensure resulting data is usable in that context. Early regulatory analysis and licensing approach planning thus provides a significant benefit to the formulation of research plans and also enables the planning and development of a compatible AdvSMR licensing framework, should significant modification be required.