WorldWideScience

Sample records for refinery energy profile

  1. Energy use in petroleum refineries

    Energy Technology Data Exchange (ETDEWEB)

    Haynes, V.O.

    1976-09-01

    Refining petroleum accounts for about 4 percent of the total energy consumed in the United States and about 15 percent of all industrial consumption. The kinds of energy used and the manner in which energy is used are discussed on a process-by-process basis. Emphasis is placed on existing processes to identify and quantify process and equipment substitutions which might significantly conserve energy. General industry and process information is given and estimates of potential savings are made. A few research and development opportunities are identified and nontechnical factors are discussed. Nearly one-half the energy consumed by refineries is obtained from by-product refinery gas and coke, and about one-third is supplied by natural gas. On a regional basis, refineries were found to vary by a factor of two in the amount of energy used to refine a unit of crude oil. Refineries in regions traditionally abundant in inexpensive natural gas were found to use relatively more natural gas and energy. About 36 percent of the energy used by petroleum refineries is consumed in the distillation units to separate the refinery streams into their basic components. Including energy for manufacturing hydrogen, about 24 percent of the total is used for cracking of the heavier components. Most of the remainder is used for reforming, hydrogen treating, and alkylation, distributed about 11, 17, and 6 percent respectively. Potential energy savings discussed in this report total 61 x 10/sup 13/ Btu/yr based on 1974 capacities, a figure which represents about 20 percent of the energy consumed to refine petroleum.

  2. Tactical Garbage to Energy Refinery

    Science.gov (United States)

    2009-10-01

    Petroleum based Pyrolysis to bio-oil Biodiesel (fluid .6) Fuel cells, PEMs generators * Bio-based Gasification to energy Methane (gas .97) Liquid fuel for...Biotechnol. 2007, 108, 67-93. 9. Patzek, T.W. Thermodynamics of the Corn -Ethanol Biofuel Cycle. Curr. Rev. Plant Sci. 2004,23,519-567 10. Canes, M.E

  3. Energy saving in refineries and petrochemical complexes

    Energy Technology Data Exchange (ETDEWEB)

    Verde, L

    1975-01-01

    Possible measures applicable in the design of refineries and petrochemical complexes, to effect energy savings were investigated. This was not limited to the single process unit problems, on the contrary the attention is mainly addressed to the identification of the interrelations between different units, emphasizing possible integrations. Particularly, the optimization of the pressure levels and number of the utility networks for steam distribution inside plant facilities, is considered, in order to maximize heat recovery in the process units, and electric power production in the central steampower generation plant. A computer program of general application, based on profitability evaluation at various fuel oil prices and different project configurations, has been developed for these purposes. The general measures applicable within certain limits are then briefly examined. The task of the process engineer is discussed in the perspective of the ''energy saving'' goal.

  4. The energy efficiency of crude oil refining in Brazil: A Brazilian refinery plant case

    International Nuclear Information System (INIS)

    Lima, Romulo S. de; Schaeffer, Roberto

    2011-01-01

    This article evaluates energy efficiency in Brazilian crude oil refining in comparison with the crude oil refining in the United States between 1930 and 2008. It aims to show that increased refinery complexity reduces the energy consumption of products of high value added. Moreover, the article shows that improvements in energy efficiency result in higher quality products and increased processing of oil. A Brazilian refinery with a capacity of 157,000 barrels per day (kbpd) was modernized in 2008 at a cost of US $1.3 billion. As a result, its capacity increased by 17%, from 157 to 189 kbpd. Its complexity index also rose from 3.2 to 6.8, allowing an improvement in the EII (energy intensity index) from 110% to 93%. In relation to the crude oil processed before being modernized, energy consumption fell from 0.75 to 0.52 MBtu (million British thermal units) per barrel processed. These proceedings show that increases in complexity reduce the energy consumed in the production of final products with high value added, such as gasoline, diesel and jet fuel. -- Highlights: → Increased refinery complexity reduces the energy consumption of products of high value added. → Improvements in refinery energy efficiency result in higher quality products and increased processing of oil. → Brazilian refineries were not affected significantly in the 2008 crisis, such as the US refineries, due to many factors. → The EII of Brazilian refining presents real opportunities for gains through changes in the profile of energy consumed.

  5. Energy efficiency improvement and cost saving opportunities forpetroleum refineries

    Energy Technology Data Exchange (ETDEWEB)

    Worrell, Ernst; Galitsky, Christina

    2005-02-15

    The petroleum refining industry in the United States is the largest in the world, providing inputs to virtually any economic sector,including the transport sector and the chemical industry. The industry operates 146 refineries (as of January 2004) around the country,employing over 65,000 employees. The refining industry produces a mix of products with a total value exceeding $151 billion. Refineries spend typically 50 percent of cash operating costs (i.e., excluding capital costs and depreciation) on energy, making energy a major cost factor and also an important opportunity for cost reduction. Energy use is also a major source of emissions in the refinery industry making energy efficiency improvement an attractive opportunity to reduce emissions and operating costs. Voluntary government programs aim to assist industry to improve competitiveness through increased energy efficiency and reduced environmental impact. ENERGY STAR (R), a voluntary program managed by the U.S. Environmental Protection Agency, stresses the need for strong and strategic corporate energy management programs. ENERGY STAR provides energy management tools and strategies for successful corporate energy management programs. This Energy Guide describes research conducted to support ENERGY STAR and its work with the petroleum refining industry.This research provides information on potential energy efficiency opportunities for petroleum refineries. This Energy Guide introduces energy efficiency opportunities available for petroleum refineries. It begins with descriptions of the trends, structure, and production of the refining industry and the energy used in the refining and conversion processes. Specific energy savings for each energy efficiency measure based on case studies of plants and references to technical literature are provided. If available, typical payback periods are also listed. The Energy Guide draws upon the experiences with energy efficiency measures of petroleum refineries worldwide

  6. Study theorizes use of geothermal sources for energy in refineries

    NARCIS (Netherlands)

    Golombok, M.; Beintema, K.

    2008-01-01

    Geothermal sources for direct heating can theoretically serve as an alternative source of high-temperature heat in processing plants. Cutting CO2 emissions from a refinery requires reducing the amount of fuel burned. Heat obtained from geothermal energy is more efficiently used for directly powering

  7. Material resources, energy, and nutrient recovery from waste: are waste refineries the solution for the future?

    DEFF Research Database (Denmark)

    Tonini, Davide; Martinez-Sanchez, Veronica; Astrup, Thomas Fruergaard

    2013-01-01

    Waste refineries focusing on multiple outputs of material resources, energy carriers, and nutrients may potentially provide more sustainable utilization of waste resources than traditional waste technologies. This consequential life cycle assessment (LCA) evaluated the environmental performance....... Overall, the waste refinery provided global warming (GW) savings comparable with efficient incineration, MBT, and bioreactor landfilling technologies. The main environmental benefits from waste refining were a potential for improved phosphorus recovery (about 85%) and increased electricity production (by...

  8. Energy demand analysis of Port-Harcourt refinery, Nigeria and its policy implications

    International Nuclear Information System (INIS)

    Jesuleye, O.A.; Siyanbola, W.O.; Sanni, S.A.; Ilori, M.O.

    2007-01-01

    This paper analyses energy demand of Port-Harcourt refinery, Nigeria, based on information obtained from its annual publications, backed-up by spot interviews. The analytical approach adopted for the study involves the calculation of energy intensities to determine the refinery's annual energy demand for various energy types considered from 1989 to 2004. The results showed that the actual energy demand per year for processing crude oil into refined products, exceeded, in varying degrees the stipulated refinery standard of 4 barrels of oil equivalent (BOE) per 100 BOE. It varied from 4.28-8.58 BOE per 100 BOE. In terms of energy demand efficiency, this implies very poor performance of the refinery during the 16-year period under investigation. The excess demand which translates to an average daily wastage of about 2005 BOE is estimated to be $56,196 (US Dollars) based on the 2003 OPEC basket price of $28.0213 per barrel. Lack of optimal fuel utilization-mix and non-compliance with the Turn-Around-Maintenance schedules were attributed to the refinery's inefficient energy demand pattern

  9. Fuel specification, energy consumption and CO2 emission in oil refineries

    International Nuclear Information System (INIS)

    Szklo, Alexandre; Schaeffer, Roberto

    2007-01-01

    The more stringent environmental quality specifications for oil products worldwide are tending to step up energy use and, consequently, CO 2 emissions at refineries. In Brazil, for example, the stipulated reduction in the sulfur content of diesel and gasoline between 2002 and 2009 should increase the energy use of Brazil's refining industry by around 30%, with effects on its CO 2 emissions. Thus, the world refining industry must deal with trade-offs between emissions of pollutants with local impacts (due to fuel specifications) and emissions of pollutants with global impacts (due to the increased energy use at refineries to remove contaminants from oil products). Two promising technology options for refineries could ease this clash in the near-to-mid term: the reduction per se of the energy use at the refinery; and the development of treatment processes using non-hydrogen consuming techniques. For instance, in Brazilian refineries, the expanded energy use resulting from severe hydrotreatment to comply with the more stringent specifications of oil products may be almost completely offset by energy saving options and alternative desulfurization techniques, if barriers to invest in technological innovations are overcome. (author)

  10. Feasibility study report for the Imperial Valley Ethanol Refinery: a 14. 9-million-gallon-per-year ethanol synfuel refinery utilizing geothermal energy

    Energy Technology Data Exchange (ETDEWEB)

    1981-03-01

    The construction and operation of a 14,980,000 gallon per year fuel ethanol from grain refinery in the Imperial Valley of California is proposed. The Imperial Valley Ethanol Refinery (refinery) will use hot geothermal fluid from geothermal resources at the East Mesa area as the source of process energy. In order to evaluate the economic viability of the proposed Project, exhaustive engineering, cost analysis, and financial studies have been undertaken. This report presents the results of feasibility studies undertaken in geothermal resource, engineering, marketing financing, management, environment, and permits and approvals. The conclusion of these studies is that the Project is economically viable. US Alcohol Fuels is proceeding with its plans to construct and operate the Refinery.

  11. Impact of Energy Production on Respiratory Outcomes: Evidence from the Flandres Refinery in France

    International Nuclear Information System (INIS)

    Lavaine, Emmanuelle

    2016-01-01

    This article examines the impact of sulphur dioxide (SO_2) concentration on respiratory admissions in the north of France at municipal level from 2007 to 2011. The Flandres refinery closure in the north of France, in September 2009, is used as a natural experiment. First, this study shows that the halt in the refinery's operations, followed by its closure in 2010, reduces SO_2 concentration. We then use this exogenous shock to analyse the health impact of the high SO_2 concentration generated by energy production. Our estimates highlight that the reduction in SO_2 concentration has significantly reduced the severity of respiratory outcomes. Additionally, the refinery closure has had statistically significant effects on the revenue of municipalities in the area

  12. Optimal Renewable Energy Integration into Refinery with CO2 Emissions Consideration: An Economic Feasibility Study

    Science.gov (United States)

    Alnifro, M.; Taqvi, S. T.; Ahmad, M. S.; Bensaida, K.; Elkamel, A.

    2017-08-01

    With increasing global energy demand and declining energy return on energy invested (EROEI) of crude oil, global energy consumption by the O&G industry has increased drastically over the past few years. In addition, this energy increase has led to an increase GHG emissions, resulting in adverse environmental effects. On the other hand, electricity generation through renewable resources have become relatively cost competitive to fossil based energy sources in a much ‘cleaner’ way. In this study, renewable energy is integrated optimally into a refinery considering costs and CO2 emissions. Using Aspen HYSYS, a refinery in the Middle East was simulated to estimate the energy demand by different processing units. An LP problem was formulated based on existing solar energy systems and wind potential in the region. The multi-objective function, minimizing cost as well as CO2 emissions, was solved using GAMS to determine optimal energy distribution from each energy source to units within the refinery. Additionally, an economic feasibility study was carried out to determine the viability of renewable energy technology project implementation to overcome energy requirement of the refinery. Electricity generation through all renewable energy sources considered (i.e. solar PV, solar CSP and wind) were found feasible based on their low levelized cost of electricity (LCOE). The payback period for a Solar CSP project, with an annual capacity of about 411 GWh and a lifetime of 30 years, was found to be 10 years. In contrast, the payback period for Solar PV and Wind were calculated to be 7 and 6 years, respectively. This opens up possibilities for integrating renewables into the refining sector as well as optimizing multiple energy carrier systems within the crude oil industry

  13. Optimization of operating conditions of distillation columns: an energy saving option in refinery industry

    Directory of Open Access Journals (Sweden)

    Alireza Fazlali

    2010-01-01

    Full Text Available While energy prices continue to climb, it conservation remains the prime concern for process industries. The daily growth of energy consumption throughout the world and the real necessity of providing it, shows that optimization of energy generation and consumption units is an economical and sometimes vital case. Hence, the optimization of a petroleum refinery is aimed towards great production and an increase in quality. In this research, the atmospheric distillation unit of the Iran-Arak-Shazand petroleum refinery was subject to optimization efforts. It was performed by the means of using a simulator with the aim to earn more overhead products. In the next step the optimization results from the simulators were carried out in the real world, at the above mentioned unit. Results demonstrate that the changes in the real operating conditions increase the overhead products with desirable quality. Finally, a net economical balance between the increments of the overhead products and the energy consumption shows an energy saving in this refinery.

  14. Reconstruction of refinery industry in Chechen Republic on the resource- and energy-saving basis

    Energy Technology Data Exchange (ETDEWEB)

    Geieva, L.A.; Meshalkin, V.P.; Sarkissov, P.D. [Mendeleev Univ. of Chemical Technology of Russia, Moscow (Russian Federation); Hadzhiev, S.N. [Inst. of Petrochemical Synthesis of Russian Academy of Sciences after A.V. Topchiev (Russian Federation)

    2003-07-01

    In 2000, the Russian Federation implemented measures to increase oil production in the Chechen Republic from 73 thousand metric tons to 1.5 million metric tons by 2002. As a result, the oil refining industry in the Chechen Republic is currently in a state of crisis. More advanced and effective refining processes are required along with a reduction in production costs. The reconstruction program for refineries in Grozny requires new process system designs that can handle the appropriate petroleum products in the correct quantities and required qualities. There is also a need to balance the use of natural resources with fixed facilities and operating costs. The challenge to design optimal process systems for refineries in Grozny is both multicriterial and complex. The design will have to consider the use of various crudes and petroleum products. Advances in refining capability and resource conservation technologies would lead to greater energy consumption resulting from additional petroleum production.

  15. Analysis of the sector petroleum refineries in energy scenarios for The Netherlands. Analyse van de sector raffinaderijen voor de Nationale Energie Verkenningen

    Energy Technology Data Exchange (ETDEWEB)

    Van Oostvoorn, F

    1926-07-01

    The calculations with regard to the oil sector in general and the petroleum refineries in particular of the energy scenarios for The Netherlands are described. Calculations have been made with the help of the energy models SELPE and SERUM, developed for the total energy scene of The Netherlands and the petroleum refineries respectively. The results of the calculations with respect to the petroleum refineries are compared. This resulted in adjustment of the parameters for the oil sector in the SELPE energy model and the consequences of these adjustments for the energy scenarios for The Netherlands. 3 figs., 15 tabs., 10 refs.

  16. Petroleum: An energy profile, 1999

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-07-01

    This report prepared by the Energy Information Administration covers the following topics: petroleum production and end-use sectors; resources and reserves; exploration and production; LPG sources and processing; motor gasoline octane enhancement; constructing pipelines; the strategic petroleum reserve; imports and exports; marketing; district descriptions and maps; and refinery processes and facilities. 33 figs., 7 tabs.

  17. Nuclear refinery - advanced energy complex for electricity generation, clean fuel production, and heat supply

    International Nuclear Information System (INIS)

    McDonald, C.F.

    1992-01-01

    In planning for increased U.S. energy users' demand after the year 2000 there are essentially four salient vectors: (1) reduced reliance on imported crude oil; (2) provide a secure supply with stable economics; (3) supply system must be in concert with improved environment goals; and (4) maximum use to be made of indigenous resources. For the last decade of this century the aforementioned will likely be met by increasing utilization of natural gas. Early in the next century, however, in the U.S. and the newly industrializing nations, the ever increasing energy demand will only be met by the combined use of uranium and coal. The proposed nuclear refinery concept is an advanced energy complex that has at its focal point an advanced modular helium reactor (MHR). This nuclear facility, together with a coal feedstock, could contribute towards meeting the needs of the four major energy sectors in the U.S., namely electricity, transportation, industrial heating and chemical feedstock, and space and water heating. Such a nuclear/coal synergistic system would be in concert with improved air quality goals. This paper discusses the major features and multifaceted operation of a nuclear refinery concept, and identifies the enabling technologies needed for such an energy complex to become a reality early in the 21st century. (Author)

  18. Analysis of the overall energy intensity of alumina refinery process using unit process energy intensity and product ratio method

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Liru; Aye, Lu [International Technologies Center (IDTC), Department of Civil and Environmental Engineering,The University of Melbourne, Vic. 3010 (Australia); Lu, Zhongwu [Institute of Materials and Metallurgy, Northeastern University, Shenyang 110004 (China); Zhang, Peihong [Department of Municipal and Environmental Engineering, Shenyang Architecture University, Shenyang 110168 (China)

    2006-07-15

    Alumina refinery is an energy intensive industry. Traditional energy saving methods employed have been single-equipment-orientated. Based on two concepts of 'energy carrier' and 'system', this paper presents a method that analyzes the effects of unit process energy intensity (e) and product ratio (p) on overall energy intensity of alumina. The important conclusion drawn from this method is that it is necessary to decrease both the unit process energy intensity and the product ratios in order to decrease the overall energy intensity of alumina, which may be taken as a future policy for energy saving. As a case study, the overall energy intensity of the Chinese Zhenzhou alumina refinery plant with Bayer-sinter combined method between 1995 and 2000 was analyzed. The result shows that the overall energy intensity of alumina in this plant decreased by 7.36 GJ/t-Al{sub 2}O{sub 3} over this period, 49% of total energy saving is due to direct energy saving, and 51% is due to indirect energy saving. The emphasis in this paper is on decreasing product ratios of high-energy consumption unit processes, such as evaporation, slurry sintering, aluminium trihydrate calcining and desilication. Energy savings can be made (1) by increasing the proportion of Bayer and indirect digestion, (2) by increasing the grade of ore by ore dressing or importing some rich gibbsite and (3) by promoting the advancement in technology. (author)

  19. Fiscal 1999 feasibility study on energy conservation at Novo-oil refinery in Ufa City

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-31

    An energy conservation plan was examined for Novo oil refinery of Bashneftechim Company in Ufa City, Bashkortstan, Russia for the purpose of making the plan tied to the COP3 joint implementation. The objective units in the study include an atmospheric and vacuum distillation unit with throughput of 7.8 million tons/year, a visbreaker and a vacuum gas oil hydrodesulfurization unit (for feedstock of FCC in Lenin Refinery), and a catalytic cracking unit, for example. Energy conservation measures are improvement and revamping of heating furnace to control excess air ratio in furnace, installation of air pre-heater or heat recovery boiler to recover heat from exhaust gas of heating furnace, additional installation of heat exchangers to recover heat from product oils, and efficiency improvement of overall operation by modernization of instrumentation and controlling equipment. The policy is not complete rebuilding of the facilities but utilizing the existing facilities by improving energy efficiency as far as possible. The study shows that investment for energy saving will be recovered within 3-6 years in many cases while total investment is estimated to be 1.5-3.0 billion yen. Total reduction of fuel consumption will be 500-800 million yen. Yearly reduction of CO2 emission will amount to 0.29 million tons (23%). (NEDO)

  20. Case study of energy conservation at national refinery limited, Karachi (Pakistan)

    International Nuclear Information System (INIS)

    Shah, F.A.; Shaikh, M.B.; Mahesar, G.H.

    2000-01-01

    Petroleum refining is one of the four top most industries in Pakistan in energy consumption and to save energy is the concern of every one. In this research, authors have calculated the designed and actual efficiency of the industrial furnaces at ''Two stage distillation unit'' of National Refinery Limited, Karachi. Observations were made for energy (Oil) consumption, heat (radiation) losses, through the furnace wall, tubing and stacks flue gases. The study shows difference in the data given at the time of design and at present working data. The furnace (01-F1) is 60% efficient and recorded 9% pounds of oil more per hour, giving 18% more heat loss. The reasons behind the fuel and energy losses are discussed with the suggestions. (authors)

  1. Bio-Refineries Bioprocess Technologies for Waste-Water Treatment, Energy and Product Valorization

    Science.gov (United States)

    Keith Cowan, A.

    2010-04-01

    Increasing pressure is being exerted on communities and nations to source energy from forms other than fossil fuels. Also, potable water is becoming a scarce resource in many parts of the world, and there remains a large divide in the demand and utilization of plant products derived from genetically modified organisms (GMOs) and non-GMOs. The most extensive user and manager of terrestrial ecosystems is agriculture which is also the de facto steward of natural resources. As stated by Miller (2008) no other industry or institution comes close to the comparative advantage held for this vital responsibility while simultaneously providing food, fiber, and other biology-based products, including energy. Since modern commercial agriculture is transitioning from the production of bulk commodities to the provision of standardized products and specific-attribute raw materials for differentiated markets, we can argue that processes such as mass cultivation of microalgae and the concept of bio-refineries be seen as part of a `new' agronomy. EBRU is currently exploring the integration of bioprocess technologies using microalgae as biocatalysts to achieve waste-water treatment, water polishing and endocrine disruptor (EDC) removal, sustainable energy production, and exploitation of the resultant biomass in agriculture as foliar fertilizer and seed coatings, and for commercial extraction of bulk commodities such as bio-oils and lecithin. This presentation will address efforts to establish a fully operational solar-driven microalgae bio-refinery for use not only in waste remediation but to transform waste and biomass to energy, fuels, and other useful materials (valorisation), with particular focus on environmental quality and sustainability goals.

  2. Three dimensional energy profile:

    International Nuclear Information System (INIS)

    Kowsari, Reza; Zerriffi, Hisham

    2011-01-01

    The provision of adequate, reliable, and affordable energy has been considered as a cornerstone of development. More than one-third of the world's population has a very limited access to modern energy services and suffers from its various negative consequences. Researchers have been exploring various dimensions of household energy use in order to design strategies to provide secure access to modern energy services. However, despite more than three decades of effort, our understanding of household energy use patterns is very limited, particularly in the context of rural regions of the developing world. Through this paper, the past and the current trends in the field of energy analysis are investigated. The literature on rural energy and energy transition in developing world has been explored and the factors affecting households' decisions on energy use are listed. The and the factors affecting households' decisions on energy use are listed. The gaps identified in the literature on rural household energy analysis provide a basis for developing an alternative model that can create a more realistic view of household energy use. The three dimensional energy profile is presented as a new conceptual model for assessment of household energy use. This framework acts as a basis for building new theoretical and empirical models of rural household energy use. - Highlights: ► Reviews literature on household energy, energy transitions and decision-making in developing countries. ► Identifies gaps in rural household energy analysis and develops a new conceptual framework. ► The 3-d energy profile provides a holistic view of household energy system characteristics. ► Illustrates the use of the framework for understanding household energy transitions.

  3. Retrofitting refinery and petrochemical plants

    Energy Technology Data Exchange (ETDEWEB)

    Kesler, M.G.

    1988-06-01

    This article focuses on process improvements as the best way to reduce plant energy use. The emphasis on process revamp is well justified, as an energy profile for a typical refinery shows. The diagram shows that 60% of the total heat losses are in water and air cooling. Most of this heat loss results from condensing and cooling in fractionators and recycle systems, intermediate product cooling, and condensing of turbine steam. These losses, of mostly low-level heat, are tied to the basic approach previously used for the process design of existing refineries. Despite the progress to date, there is growing evidence that these heat losses can be further reduced economically by about 20-30% in most refineries and petrochemical plants. One way to reduce the losses is to increase recovery of low-level heat by improved heat exchange, which has been the subject of most publications on plant energy conservation. A better way, presented here, is to develop new process schemes that require less air/water cooling. One useful concept in developing new schemes is to concentrate on heat losses, rather than heat input, as an easier measure of proposed improvements. By an overall heat balance, eliminating a unit of energy loss is equivalent to saving a unit of heat input somewhere in the plant.

  4. WPC (Madrid): Block Downstream and Petrochemicals - Best Practices session: novel approaches to improve energy efficiency at refineries

    International Nuclear Information System (INIS)

    Anon.

    2008-01-01

    This session: 'Novel approaches to improve energy efficiency at refineries', includes two key-note addresses. During the first one, entitled 'refinery energy efficiency today', Zoran Milosevic (KBC) has reported a survey of the current situation and of the improvements margins for the future. Hereafter, this work takes again in developing them, the main messages of the address of Jean-Bernard Sigaud, whose aim was to attract attention on the requirement of a rigorous methodological approach in order to avoid that the decisions taken to abate the energy consumption or the CO 2 releases at the local level, result in fine to the inverse result of those of the world level. This work shows particularly why the traditional perception of a refinery energy balance, which consists to assimilate the fuel consumption to an energy consumption, can lead to deep misinterpretations. It shows too in what the hydrogen transfer amounts to de-localize the energy consumption (which occurs essentially where the hydrogen is consumed) compared to the corresponding CO 2 releases which are produced where hydrogen is produced. At last, a comparison between the different channels for the electric power production and the synthesized fuels, illustrates the crucial importance to use each technology deliberately, while underlining the character sometimes under-intuitive of the good decision. (O.M.)

  5. Feasibility study on an energy conservation project at Tabriz Refinery in Iran

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of saving energy and reducing greenhouse gas emission, a feasibility study has been executed to discuss applicable measures on oil refining facilities in Tabriz Oil Refinery in Islamic Republic of Iran. The discussion objects are the ten devices related to atmospheric and reduced pressure distillation, visbreaker, naphtha hydrogenating desulfurization, naphtha contact reforming, reduced pressure hydro-cracking of light oil, hydrogen manufacturing, amine rinsing, asphalt manufacturing, and boilers. Major improvement items include: modification of the excessive air ratio control facility, installation of a superheating furnace waste gas recovering device, additional installation of heat exchangers in the raw material oil preheating system, and increased heat recovery by improving distribution of distillation column reflux. As a result of the feasibility study, the investment recovery performance was anticipated to be contained within about five years, with consideration on procurement of some of the devices in Iran. The approximate investment amount would be 2 billion yen, the annual fuel saving amount would be about 660 million yen, and the energy saving ratio would be 13.5%. The carbon dioxide emission quantity would be reduced annually by about 155.8 tons, as contrasted to the annual emission of 1,158,000 tons from the existing facilities. (NEDO)

  6. Well-to-refinery emissions and net-energy analysis of China's crude-oil supply

    Science.gov (United States)

    Masnadi, Mohammad S.; El-Houjeiri, Hassan M.; Schunack, Dominik; Li, Yunpo; Roberts, Samori O.; Przesmitzki, Steven; Brandt, Adam R.; Wang, Michael

    2018-03-01

    Oil is China's second-largest energy source, so it is essential to understand the country's greenhouse gas emissions from crude-oil production. Chinese crude supply is sourced from numerous major global petroleum producers. Here, we use a per-barrel well-to-refinery life-cycle analysis model with data derived from hundreds of public and commercial sources to model the Chinese crude mix and the upstream carbon intensities and energetic productivity of China's crude supply. We generate a carbon-denominated supply curve representing Chinese crude-oil supply from 146 oilfields in 20 countries. The selected fields are estimated to emit between 1.5 and 46.9 g CO2eq MJ-1 of oil, with volume-weighted average emissions of 8.4 g CO2eq MJ-1. These estimates are higher than some existing databases, illustrating the importance of bottom-up models to support life-cycle analysis databases. This study provides quantitative insight into China's energy policy and the economic and environmental implications of China's oil consumption.

  7. Basic survey for Joint Implementation on Jinling Petrochemical Corporation, China. Energy conservation project for Nanjing Refinery

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing greenhouse effect gas emissions, the basic survey was conducted on potential energy conservation at Nanjing Refinery, Jiangsu Nanjing city, China. Investigational studies were made on the repair of the power recovery system in line with the plan to enlarge the fluid catalytic cracker (FCC) and the power recovery using exhaust gas from the RFCC catalytic regeneration system. Moreover, the energy conservation technology to reduce power loads of the refining system was adopted to this project. As a result, it was found out that this repair plan makes recovery of the power equivalent to 10.6MW possible and produces the effect of reducing the fuel to be used. The realization of this project brings the CO2 reduction amount of approximately 70,000 t/y. It was also found out that this project not only reduces a large amount of greenhouse effect gas emissions, but contributes to profits of the plant concerned and helps improve the environment in the area concerned. For the implementation of this project, the detailed plan is expected to be further discussed. (NEDO)

  8. Refinery scheduling

    Energy Technology Data Exchange (ETDEWEB)

    Magalhaes, Marcus V.; Fraga, Eder T. [PETROBRAS, Rio de Janeiro, RJ (Brazil); Shah, Nilay [Imperial College, London (United Kingdom)

    2004-07-01

    This work addresses the refinery scheduling problem using mathematical programming techniques. The solution adopted was to decompose the entire refinery model into a crude oil scheduling and a product scheduling problem. The envelope for the crude oil scheduling problem is composed of a terminal, a pipeline and the crude area of a refinery, including the crude distillation units. The solution method adopted includes a decomposition technique based on the topology of the system. The envelope for the product scheduling comprises all tanks, process units and products found in a refinery. Once crude scheduling decisions are Also available the product scheduling is solved using a rolling horizon algorithm. All models were tested with real data from PETROBRAS' REFAP refinery, located in Canoas, Southern Brazil. (author)

  9. Feasibility study on energy saving and reduction of CO2 emissions at Pertamina's Cilacap Refinery

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of saving energy and reducing greenhouse gas emission, a basic survey has been performed on the atmospheric crude oil distillation units and the high vacuum distillation units at Cilacap Refinery in Indonesia. The first site survey in September 2000 has carried out a survey on the situation of the facilities and operation upon obtaining the facility data and operation information from Pertamina. As a result, it was revealed that there is a room of improvement in the heat recovery, whereas a modification design was executed on the improvement proposals on the heat exchanger system. However, the second site survey in November 2000 has revealed that Pertamina had executed in 1998 through 1999 the de-bottlenecking project on the crude oil atmospheric distillation units (two units) and the high vacuum distillation units (two units), by which the capability has been expanded, and the heat recovery rate has been increased. It is not possible to look for extremely large enhancement of the heat recovery rate beyond that point, and the reduction of CO2 emission would also be small. As a result of discussions, the present project was found capable of reducing annually the CO2 emission by 36,500 tons. (NEDO)

  10. Population and community profiles of small mammals inhabiting an abandoned oil refinery

    International Nuclear Information System (INIS)

    McMurry, S.T.; Lochmiller, R.L.; McBee, K.; Burks, S.L.; Quails, C.W. Jr.

    1993-01-01

    Mark-recapture techniques were used to assess population and community dynamics of resident small mammals on three contaminated and three reference sites located on or near an abandoned oil refinery in Oklahoma. Contaminated sites included areas adjacent to oil sludge containment and sedimentation pits and a land farm for treating oily sludges. Reference sites were selected based on their ecological similarity to contaminated sites. Small mammals were trapped from January 1991 to August 1992 at eight week intervals except during summer and winter during which traps were checked at 3 week intervals. Diversity was typically highest on toxic sites due primarily to the presence of house mice (Mus musculus). Similarity in small mammal community composition between sites differed most in summer. Cotton rats (Sigmodon hispidus) were the most abundant species on all sites. Reproductive activity of adult female cotton rats and survival of trappable cotton rats did not differ between sites. However, minimum number known alive and recruitment of juveniles was highest on references sites, indicating that in-utero and neonatal survival may differ between reference and contaminated sites

  11. Feasibility of flare gas reformation to practical energy in Farashband gas refinery: no gas flaring.

    Science.gov (United States)

    Rahimpour, Mohammad Reaza; Jokar, Seyyed Mohammad

    2012-03-30

    A suggested method for controlling the level of hazardous materials in the atmosphere is prevention of combustion in flare. In this work, three methods are proposed to recover flare gas instead of conventional gas-burning in flare at the Farashband gas refinery. These methods aim to minimize environmental and economical disadvantages of burning flare gas. The proposed methods are: (1) gas to liquid (GTL) production, (2) electricity generation with a gas turbine and, (3) compression and injection into the refinery pipelines. To find the most suitable method, the refinery units that send gas to the flare as well as the required equipment for the three aforementioned methods are simulated. These simulations determine the amount of flare gas, the number of GTL barrels, the power generated by the gas turbine and the required compression horsepower. The results of simulation show that 563 barrels/day of valuable GTL products is produced by the first method. The second method provides 25 MW electricity and the third method provides a compressed natural gas with 129 bar pressure for injection to the refinery pipelines. In addition, the economics of flare gas recovery methods are studied and compared. The results show that for the 4.176MMSCFD of gas flared from the Farashband gas refinery, the electricity production gives the highest rate of return (ROR), the lowest payback period, the highest annual profit and mild capital investment. Therefore, the electricity production is the superior method economically. Copyright © 2012 Elsevier B.V. All rights reserved.

  12. Yugoslavian Petroleum Refinery development program

    International Nuclear Information System (INIS)

    Ocic, Ozren

    1999-01-01

    This paper shows the analysis of the world petroleum industry development, being an important factor in planning the development of the Yugoslav petroleum industry and Pancevo Petroleum Refinery, as well. Then Yugoslav petroleum industry development is analysed, including the appropriate balances of crude oil production and crude oil products consumption. The way of realizing the basic targets are also proposed. Likewise, the analysis of the condition within West European refineries has been conducted, from the aspects of technology, energy consumption and environmental protection and the same analysis for Pancevo Petroleum Refinery has been presented, too. The analysis of the condition within the refineries in the European Union countries and comparing it with the condition within Pancevo Petroleum Refinery, makes it mainly possible to recognize the development programmes which should be realized in order that Pancevo Petroleum Refinery could reach the refining level of the EU countries. (Original)

  13. Country Energy Profile, South Africa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-08-01

    This country energy profile provides energy and economic information about South Africa. Areas covered include: Economics, demographics, and environment; Energy situation; Energy structure; Energy investment opportunities; Department of Energy (DOE) programs in South Africa; and a listing of International aid to South Africa.

  14. Country Energy Profile, South Africa

    International Nuclear Information System (INIS)

    1995-08-01

    This country energy profile provides energy and economic information about South Africa. Areas covered include: Economics, demographics, and environment; Energy situation; Energy structure; Energy investment opportunities; Department of Energy (DOE) programs in South Africa; and a listing of International aid to South Africa

  15. Refinery profitability

    International Nuclear Information System (INIS)

    Tobin, G.

    1998-01-01

    Recently there has been considerable shutting down of oil refinery capacity in response to the increasing pressures on profitability. This article examines the situation and the industry's response to it, including the drive for mergers, disposal of fuel oil, downsizing of workforces and strategic alliances. Future trends and their implications are also discussed. (UK)

  16. Feasibility study on energy saving and environmental improvement via utilization of residual oil at Petron Bataan Refinery

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A feasibility study has been performed on reduction of global warming gas emission at Bataan Refinery of Petron Company in the Republic of the Philippines by utilizing residual oil in the refinery at high efficiency. In the project, installation will be implemented on thermal power generation equipment using a low-speed diesel engine that uses residual oil as fuel, and a waste heat recovered steam generation system having NOx removing equipment at Bataan Revinary of Petron Company, in addition to the existing boiler-turbine power generation system. As a result of the discussions, the annual energy saving effect in 8 years after the installation will correspond to crude oil of 50,409 tons, and in 20 years cumulatively, it will correspond to 1,017,224 tons. The annual reduction of the global warming gas emission in 8 years after the installation will be 131,698 t-CO2, or 2,657,599 t-CO2 for 20 years cumulatively. The total investment amount for these facilities is about 4.1 billion yen, whereas the investment and energy saving effects were 10.7 tons of crude oil equivalent/year-one million yen. In addition, the investment and global warming gas emission reducing effects were 28.1 t-CO2/year-one million yen. (NEDO)

  17. Steel Energy and Environmental Profile

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2000-08-01

    Major steelmaking processes (from ironmaking through fabrication and forming) and their associated energy requirements have been profiled in this 2001 report (PDF 582 KB). This profile by Energetics, Inc. also describes the waste streams generated by each process and estimates annual emissions of CO2 and criteria pollutants.

  18. Bioenergy, material, and nutrients recovery from household waste: Advanced material, substance, energy, and cost flow analysis of a waste refinery process

    International Nuclear Information System (INIS)

    Tonini, Davide; Dorini, Gianluca; Astrup, Thomas Fruergaard

    2014-01-01

    Highlights: • We modeled material, substance, energy, and cost flows of a waste refinery process. • Ca. 56% of 1 Mg dry waste input can be recovered as bioliquid yielding 6.2 GJ biogas. • Nutrients and carbon recovery in the bioliquid was estimated to 81–89%. • The biogenic carbon in the input waste was 63% of total carbon based on 14 C analyses. • The quality of the digestate may be critical with respect to use on land. - Abstract: Energy, materials, and resource recovery from mixed household waste may contribute to reductions in fossil fuel and resource consumption. For this purpose, legislation has been enforced to promote energy recovery and recycling. Potential solutions for separating biogenic and recyclable materials are offered by waste refineries where a bioliquid is produced from enzymatic treatment of mixed waste. In this study, potential flows of materials, energy, and substances within a waste refinery were investigated by combining sampling, analyses, and modeling. Existing material, substance, and energy flow analysis was further advanced by development of a mathematical optimization model for determination of the theoretical recovery potential. The results highlighted that the waste refinery may recover ca. 56% of the dry matter input as bioliquid, yielding 6.2 GJ biogas-energy. The potential for nitrogen, phosphorous, potassium, and biogenic carbon recovery was estimated to be between 81% and 89% of the input. Biogenic and fossil carbon in the mixed household waste input was determined to 63% and 37% of total carbon based on 14 C analyses. Additional recovery of metals and plastic was possible based on further process optimization. A challenge for the process may be digestate quality, as digestate may represent an emission pathway when applied on land. Considering the potential variability of local revenues for energy outputs, the costs for the waste refinery solution appeared comparable with alternatives such as direct incineration

  19. Australia's energy profile

    International Nuclear Information System (INIS)

    Dickson, A.

    1999-01-01

    Australian Bureau of Agricultural and Resource Economics (ABARE)'s biennial fuel and electricity survey provides a comprehensive database with which is possible to examine recent trends and developments in Australia's energy market. Some key development are outlined in this article. While energy consumption in Australia has been increasing steadily since 1973-74, substantial changes have occurred 'behind the scenes' in terms of the states and sectors in which energy is consumed and the overall fuel mix. Historically, the south-eastern states of New South Wales and Victoria have accounted for the largest shares of total energy consumption In recent years, however, the dominance of New South Wales and Victoria (and particularly New South Wales) has come under pressure from the states of Queensland. Western Australia, and to a lesser extent, the Northern Territory. Each of these states has experienced rapid growth in energy consumption, due mainly to a number of strongly growing energy intensive industries, particularly in the mining and minerals processing sectors. High economic and population growth over this period were also important factors. An increase in the share of natural gas- and a corresponding decline in the share of crude oil - is the most evident change to have occurred in the fuel mix since 1973-1974. However, since 1993, the trend has changed, the share of coal (and particularly brown coal) increased strongly, making it the primary fuel source for thermal electricity generation. This recent shift has been driven by developments in Queensland and Victoria

  20. Impact of the evolution of petroleum products demand on the energy consumption and CO2 emissions of refineries

    International Nuclear Information System (INIS)

    Tehrani Nejad Moghaddam, A.

    2008-01-01

    The French refining industry is in a paradoxical situation. Although the energy efficiency of the refineries have been significantly improved their CO 2 emissions are continuously increasing and this trend will be kept in future. The origin of this paradox steams in the profound modification in the demand structure (in terms of quantity and quality) of the oil products. The objective of this dissertation is to provide answers to these paradoxical questions. This objective is achieved and can be summarized in three points: (1) the introduction of linear programming to the prospective and retrospective life cycle assessment analysis (2) the evaluation of the impact of tightening the sulfur specification on the marginal cost and marginal CO 2 contribution of oil products (3) the assessment of the average CO 2 coefficients for oil products useful in the life cycle assessment studies. (author)

  1. Oil refineries

    International Nuclear Information System (INIS)

    Boehmer, S.; Winter, B.

    2001-01-01

    In refineries in particular attention is paid to the minimization of the generation of waste. Therefor catalysts in many processes are regenerated, absorbents are recycled and oily by-products are re-refined or used as fuels. This study discusses the origin and utilization of by-products from the oil industry. The processing of crude oils causes by-products and waste resulting from the crude oil itself or from cleaning measures for water pre-treatment, effluent treatment and flue gas treatment. (author)

  2. Renewable Energy Country Profiles. Pacific

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-09-15

    The IRENA Renewable Energy Country Profiles take stock of the latest development of renewable energy in two regions where renewable energy can make a significant contribution to combat climate change and bring modern energy services to everyone: Africa and the Pacific. These two regions are presented separately in this volume and its sister publication. The country profiles combine elements of IRENA analysis with the latest information available from a vast array of sources in order to give a brief yet comprehensive and up-to-date picture of the situation of renewable energy that includes energy supply, electrical capacity, energy access, policies, targets, investment climate, projects and endowment in renewable energy resources. Because of the different timelines of these sources, data presented here refer to years between 2008 and 2012. Data availability also differs from country to country, which makes comparison with a wider regional group possible only for the year for which figures are available for all the members of the group; while this may not be the most recent year, the differences between countries, regions and the world remain striking. The current country profiles are just a starting point; they will be extended upon with new indicators to make them more informative, and maintained as a live product on the IRENA website as a key source of information on renewable energy.

  3. Renewable Energy Country Profiles. Africa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-02-15

    The IRENA Renewable Energy Country Profiles take stock of the latest development of renewable energy in two regions where renewable energy can make a significant contribution to combat climate change and bring modern energy services to everyone: Africa and the Pacific. These two regions are presented separately in this volume and its sister publication. The country profiles combine elements of IRENA analysis with the latest information available from a vast array of sources in order to give a brief yet comprehensive and up-to-date picture of the situation of renewable energy that includes energy supply, electrical capacity, energy access, policies, targets, investment climate, projects and endowment in renewable energy resources. Because of the different timelines of these sources, data presented here refer to years between 2008 and 2012. Data availability also differs from country to country, which makes comparison with a wider regional group possible only for the year for which figures are available for all the members of the group; while this may not be the most recent year, the differences between countries, regions and the world remain striking. The current country profiles are just a starting point; they will be extended upon with new indicators to make them more informative, and maintained as a live product on the IRENA website as a key source of information on renewable energy.

  4. Renewable Energy Country Profiles. Caribbean

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-09-15

    IRENA Renewable Energy Country Profiles take stock of the latest developments in the field of renewables at country level around the world. Each profile combines analysis by IRENA's specialists with the latest available country data and additional information from a wide array of sources. The resulting reports provide a brief yet comprehensive picture of the situation with regard to renewable energy, including energy supply, electrical generation and grid capacity, and access. Energy policies, targets and projects are also considered, along with each country's investment climate and endowment with renewable energy resources. The energy statistics presented here span the period from 2009 until 2012, reflecting varying timelines in the source material. Since data availability differs from country to country, wider regional comparisons are possible only for the latest year with figures available for every country included. Despite the time lag in some cases, the evident differences and disparities between countries and regions around the world remain striking. The current package of country profiles is just a starting point. The geographic scope will continue to expand, and existing profiles will be enhanced with new indicators, with the whole series maintained as a live product on the IRENA website (www.irena.org)

  5. How to perform Energy Trace & BarrierAnalysis (ETBA in industries? Acase study in Isomax Unit of Tehran refinery

    Directory of Open Access Journals (Sweden)

    J Adl

    2006-04-01

    Full Text Available Background and Aims: People, equipments and properties are continuously exposed tonumerous hazards while technology develops. The global increasing rate of accidents and workrelatedinjuries, especially in Iran, is an evidence for these hazards. There are numerous methodsfor hazard analysis such as the Energy Trace & Barrier Analysis (ETBA, which is a process ofanalysis based on system safety for detecting and definition of hazards and also risks that maycause system damage.Method: This is a case study in the Isomax unit of Tehran refinery and allied section. Datecollection and completion of the ETBAsheets were conducted through observation and interviewmethod with experts, walking - talking through method, investigation of technical and operativedocuments.Results: Twelve different kinds of energy and 28 subgroups were investigated. The types ofenergies, existence barriers, vulnerable targets, risk assessment code, and adequacy of barriers aswell as recommendations for decreasing risk level through tolerable risk were identified.Conclusion: The results of this study show potential application of ETBA in different industries,especially chemical industry, which is a method for identification hazards and prevention ofwork-related injuries.

  6. Energy markets : refinery outages can have varying gasoline price impacts, but gaps in federal data limit understanding of impacts.

    Science.gov (United States)

    2009-07-01

    In 2008, GAO reported that, with : the exception of the period : following Hurricanes Katrina and : Rita, refinery outages in the United : States did not show discernible : trends in reduced production : capacity, frequency, and location : from 2002 ...

  7. Feasibility study on energy saving and reduction of CO2 emissions at Pertamina's Cilacap Refinery

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of saving energy and reducing greenhouse gas emission, a basic survey has been performed on the atmospheric crude oil distillation units and the high vacuum distillation units at Cilacap Refinery in Indonesia. The first site survey in September 2000 has carried out a survey on the situation of the facilities and operation upon obtaining the facility data and operation information from Pertamina. As a result, it was revealed that there is a room of improvement in the heat recovery, whereas a modification design was executed on the improvement proposals on the heat exchanger system. However, the second site survey in November 2000 has revealed that Pertamina had executed in 1998 through 1999 the de-bottlenecking project on the crude oil atmospheric distillation units (two units) and the high vacuum distillation units (two units), by which the capability has been expanded, and the heat recovery rate has been increased. It is not possible to look for extremely large enhancement of the heat recovery rate beyond that point, and the reduction of CO2 emission would also be small. As a result of discussions, the present project was found capable of reducing annually the CO2 emission by 36,500 tons. (NEDO)

  8. Report of year 2000 version on feasibility study on energy conservation at Teheran Oil Refinery in Iran

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-31

    For the purpose of the COP3 joint implementation, this paper describes the report of year 2000 version on feasibility study on energy conservation at Teheran Oil Refinery in Iran. The facilities as the object of the study include those for atmospheric pressure distillation for a capacity of 125,000 BD, vacuum distillation for a capacity of 48,000 BD, visbreaker with a capacity of 21,000 BD, naphtha hydrogenated desulfurization and naphtha reforming for a capacity of 168,000 BD, vacuum gas oil hydro-cracking for a capacity of 20,000 BD, hydrogen production of 32 MMSCFD, four 32,000 lb/h boilers, and other off-site equipment. Improvement measures include control of excessive air rate in heating furnaces, installation of air heaters and waste heat boilers to recover heat from the heating furnace stack gas, and increase in heat recovery from interim reflux. The period to recover the energy conservation investment would be about one year for the control of oxygen concentration in the stack gas, and three to five years for other main devices. The total investment amount is estimated to be 10 to 15 billion yen. Annual fuel saving would amount to 600 to 800 million yen. CO2 emission of 1.38 million tons before applying the measures will be reduced by 260,000 tons after the measures would have been applied, or 19% reduction. The country's own fund will be used for small scale modification, but financial and technological assistance from Japan is desired for medium to large scale modification. (NEDO)

  9. Report of year 2000 version on feasibility study on energy conservation at Teheran Oil Refinery in Iran

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-31

    For the purpose of the COP3 joint implementation, this paper describes the report of year 2000 version on feasibility study on energy conservation at Teheran Oil Refinery in Iran. The facilities as the object of the study include those for atmospheric pressure distillation for a capacity of 125,000 BD, vacuum distillation for a capacity of 48,000 BD, visbreaker with a capacity of 21,000 BD, naphtha hydrogenated desulfurization and naphtha reforming for a capacity of 168,000 BD, vacuum gas oil hydro-cracking for a capacity of 20,000 BD, hydrogen production of 32 MMSCFD, four 32,000 lb/h boilers, and other off-site equipment. Improvement measures include control of excessive air rate in heating furnaces, installation of air heaters and waste heat boilers to recover heat from the heating furnace stack gas, and increase in heat recovery from interim reflux. The period to recover the energy conservation investment would be about one year for the control of oxygen concentration in the stack gas, and three to five years for other main devices. The total investment amount is estimated to be 10 to 15 billion yen. Annual fuel saving would amount to 600 to 800 million yen. CO2 emission of 1.38 million tons before applying the measures will be reduced by 260,000 tons after the measures would have been applied, or 19% reduction. The country's own fund will be used for small scale modification, but financial and technological assistance from Japan is desired for medium to large scale modification. (NEDO)

  10. Report of fiscal 1999 basic survey for joint implementation, etc. Feasibility study on energy conservation and reduction of CO2 emission at Omsk Refinery

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper explains fiscal 1999 survey on energy conservation and reduction of CO2 at Omsk Refinery in the Russian Federation for the purpose of making the project tied to the COP3 joint implementation. This refinery is the largest class refinery in Russia having a capacity of 600,000 BPSD. The atmospheric distillation unit AVT-10, which emits 470,000 t-CO2/year, was selected for the object of the survey. As the modification plans, optimization of process system, modification of waste heat boiler and installation of new furnaces were considered. The plans 1, 2 are possible due to their low investment costs. The plan 3 to install new furnaces is able to reduce the large volume of CO2 emission though its investment cost is higher. For each modification plan, estimation was made for the investment cost, the benefit by energy saving and the volume of reduction of CO2 emission. The results for each of the plans 1, 2 and 3 were 907x10{sup 3}, 3,377x10{sup 3}, 50,400x10{sup 3} in US$; 535x10{sup 3}, 928x10{sup 3}, 1,407x10{sup 3} in US$; and 36.1x10{sup 3}, 68.2x10{sup 3}, 86.6x10{sup 3} tons/year. The Russian side showed their satisfaction of the results and keen interest in the energy saving effect. For the purpose of realizing this plan, financial assistance and technological cooperation are essential. Russia shows their great expectations for the Japanese government. (NEDO)

  11. Basic survey for Joint Implementation on West Pacific Petrochemical Co., Ltd., Dalian, China. Energy conservation project for West Pacific Oil Refinery

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing greenhouse effect gas emissions, a potential survey was conducted of energy conservation at West Pacific Oil Refinery, Dalian, China. In the survey, studies were made of energy conservation by introducing the hydrogen recovery equipment and the gas turbine generation system using exhaust gas as fuel, and of potentiality of reducing greenhouse effect gas emissions. As a result of the survey, a gas turbine generator of about 29MW using the surplus gas as fuel can be installed. By this, approximately 71% of the power used in refinery is to be supplied as against 25% of the power presently used. The technology was proposed on the hydrogen recovery equipment and the gas turbine generation system to discuss the revision plan with the Chinese partner. When this project is realized, the reduction amount of CO2 will be 136,000 ton/y. The Chinese side highly estimated not only the remarkable reduction in CO2, but the reduction in purchased power from outside which is to be brought by realization of this project. (NEDO)

  12. The refinery industry within the Mediterranean area

    International Nuclear Information System (INIS)

    1999-01-01

    During the period 1997-1998 Ome (Observatorie Mediterraneen de l'Energie) within a working group which was formed by the experts among the associated companies, has carried on an analysis on the prospects of refinery industry in the Mediterranean area in view of 2010. The aim of this study was to make clear, to the different operators, the consequences of the political choices in investments on refinery industry in the context of the progressive liberalization of the sector [it

  13. Current situation of oil refinery in Bulgaria

    Science.gov (United States)

    Vershkova, Elena; Petkova, Petinka; Grinkevich, Anastasia

    2016-09-01

    This article deals with the classification approach for oil refineries in international practices. Criteria of refinery estimation group, including its financial status estimation, have been investigated. The analysis object is “Lukoil Neftochim Bourgas” AD (LNCHB) activity. This company is a leading enterprise in Bulgaria. The analysis of LNCHB operating: energy intensity index; index of operating costs and return on investment index have been performed.

  14. Fiscal 1998 joint promotion basic research report. Energy saving project for Achinsk refinery in Russia; 1998 nendo kyodo jisshi nado suishin kiso chosa. Roshia Achinsuku seiyujo shoene project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For prevention of global warming by greenhouse effect gas, study was made on energy saving measures for Achinsk refinery in Russia. Achinsk refinery is a relatively new plant put into operation in 1983, however, because of no various equipment for use combustion heat effectively, its average thermal efficiency is as low as 60%-70%, resulting in fuel consumption more than necessary one. Based on the study result, the following remodeling designs were made: Improvement of a heat exchange efficiency by relocation of heat exchangers to reduce fuel consumption of a heating furnace as much as possible, conversion of an existing heating furnace based on an old design concept to an advanced one, installation of a waste heat recovery system including a preheating convection unit and air preheater, reinforcement of heating furnace wall insulator, installation of an optimum control system for furnace operation, and improvement of a fuel supply system efficiency. This design showed possible reduction of heating furnace load, and possible furnace thermal efficiency of 90%. (NEDO)

  15. 2004 energy balances and electricity profiles

    International Nuclear Information System (INIS)

    2007-02-01

    The Energy Balances and Electricity Profiles 2004 is the thirteenth issue in an internationally series of comparable energy data for selected developing countries. The data are arranged to show energy production, trade, conversion and consumption for each fuel used in the country. This publication is a source of overall consumption statistics of energy commodities in all sectors. Special electricity profiles for an additional group of countries are published to cover, exclusively, detailed information on production, trade and consumption of electricity, net installed capacity and thermal power plant input for selected developing countries

  16. Performance profiles of major energy producers 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    Performance Profiles of Major Energy Producers 1994 is the eighteenth annual report of the Energy Information Administration`s (EIA) Financial Reporting System (FRS). The report examines financial and operating developments in energy markets, with particular reference to the 24 major U.S. energy companies required to report annually on Form EIA-28. Financial information is reported by major lines of business, including oil and gas production, petroleum refining and marketing, other energy operations, and nonenergy businesses. Financial and operating results are presented in the context of energy market developments with a view toward identifying changing corporate strategies and measuring the performance of ongoing operations both in the United States and abroad.

  17. Illustrating Enzyme Inhibition Using Gibbs Energy Profiles

    Science.gov (United States)

    Bearne, Stephen L.

    2012-01-01

    Gibbs energy profiles have great utility as teaching and learning tools because they present students with a visual representation of the energy changes that occur during enzyme catalysis. Unfortunately, most textbooks divorce discussions of traditional kinetic topics, such as enzyme inhibition, from discussions of these same topics in terms of…

  18. 1998 energy balances and electricity profiles

    International Nuclear Information System (INIS)

    2001-01-01

    This is the tenth issue of Energy Balances and Electricity Profiles published by the Statistics Division of the United Nations Secretariat. Like previous issues, this volume presents energy data for selected countries in a format which shows the overall picture of energy production, conversion and consumption for fuels utilised in the country. Such a publication is useful in assessing and analysing production and consumption patterns in detail on an internationally comparable basis. Since it began publishing energy balances, the Statistics Division has adopted the matrix type of overall energy balance that shows energy sources in the columns and energy flows in the rows. The format is described in detail in the technical report entitled Concepts and Methods in Energy Statistics, with Special Reference to Energy Accounts and Balances and is also discussed in the publication, Energy Statistics: A Manual for Developing Countries. The level of detail of this matrix structure takes into account the need for disaggregation of the energy sector and final demand, while at the same time, owing to the limitations in the quantity and quality of the currently available energy information, coverage has to be restricted to the main sectors only. Furthermore, it should be recognized that unlike national energy balances designed for individual countries' various specific needs, the energy balance format of the Statistics Division has to accommodate the whole spectrum of national energy data which it receives from national statistical offices and through official national publications. Inasmuch as information on electricity is generally available in greater detail than that for other energy forms, the Statistics Division decided to present special electricity profiles for an additional group of countries and areas, thereby covering at least part of their energy conversion and consumption activities. World energy data is published by the Statistics Division in the Energy Statistics

  19. 2000 energy balances and electricity profiles

    International Nuclear Information System (INIS)

    2004-01-01

    This is the eleventh issue of Energy Balances and Electricity Profiles published by the Statistics Division of the United Nations Secretariat. Like previous issues, this volume presents energy data for selected countries in a format which shows the overall picture of energy production, conversion and consumption for fuels utilised in the country. Such a publication is useful in assessing and analysing production and consumption patterns in detail on an internationally comparable basis. Since it began publishing energy balances, the Statistics Division has adopted the matrix type of overall energy balance that shows energy sources in the columns and energy flows in the rows. The format is described in detail in the technical report entitled Concepts and Methods in Energy Statistics, with Special Reference to Energy Accounts and Balances and is also discussed in the publication, Energy Statistics: A Manual for Developing Countries. The level of detail of this matrix structure takes into account the need for disaggregation of the energy sector and final demand, while at the same time, owing to the limitations in the quantity and quality of the currently available energy information, coverage has to be restricted to the main sectors only. Furthermore, it should be recognized that unlike national energy balances designed for individual countries' various specific needs, the energy balance format of the Statistics Division has to accommodate the whole spectrum of national energy data which it receives from national statistical offices and through official national publications. Inasmuch as information on electricity is generally available in greater detail than that for other energy forms, the Statistics Division decided to present special electricity profiles for an additional group of countries and areas, thereby covering at least part of their energy conversion and consumption activities. World energy data is published by the Statistics Division in the Energy

  20. 2002 energy balances and electricity profiles

    International Nuclear Information System (INIS)

    2005-01-01

    This is the twelfth issue of Energy Balances and Electricity Profiles published by the Statistics Division of the United Nations Secretariat. Like previous issues, this volume presents energy data for selected countries in a format which shows the overall picture of energy production, conversion and consumption for fuels utilised in the country. Such a publication is useful in assessing and analysing production and consumption patterns in detail on an internationally comparable basis. Since it began publishing energy balances, the Statistics Division has adopted the matrix type of overall energy balance that shows energy sources in the columns and energy flows in the rows. The format is described in detail in the technical report entitled Concepts and Methods in Energy Statistics, with Special Reference to Energy Accounts and Balances and is also discussed in the publication, Energy Statistics: A Manual for Developing Countries. The level of detail of this matrix structure takes into account the need for disaggregation of the energy sector and final demand, while at the same time, owing to the limitations in the quantity and quality of the currently available energy information, coverage has to be restricted to the main sectors only. Furthermore, it should be recognized that unlike national energy balances designed for individual countries' various specific needs, the energy balance format of the Statistics Division has to accommodate the whole spectrum of national energy data which it receives from national statistical offices and through official national publications. Inasmuch as information on electricity is generally available in greater detail than that for other energy forms, the Statistics Division decided to present special electricity profiles for an additional group of countries and areas, thereby covering at least part of their energy conversion and consumption activities. World energy data is published by the Statistics Division in the Energy

  1. 1994 energy balances and electricity profiles

    International Nuclear Information System (INIS)

    1996-01-01

    This is the eighth issue of Energy Balances and Electricity Profiles published by the Statistics Division of the United Nations Secretariat. Like previous issues, this volume presents energy data for selected countries and areas in a format which shows the overall picture of energy production, conversion and consumption for each fuel utilized in the country. Such a publication is useful in assessing and analyzing production and consumption patterns in detail on an internationally comparable basis

  2. 1992 energy balances and electricity profiles

    International Nuclear Information System (INIS)

    1994-01-01

    This is the seventh issue of Energy Balances and Electricity Profiles published by the Statistical Division of the United Nations Secretariat. Like previous issues, this volume presents energy data for selected developing countries and areas in a format which shows the overall picture of energy production, conversion and consumption for each fuel utilised in the country. Such a publication is useful in assessing and analyzing production and consumption patterns in detail on an internationally comparable basis

  3. Performance profiles of major energy producers 1992

    International Nuclear Information System (INIS)

    1994-01-01

    Performance Profiles of Major Energy Producers 1992 is the sixteenth annual report of the Energy Information Administration's (EIA) Financial Reporting System (FRS). The report examines financial and operating developments, with particular reference to the 25 major energy companies (the FRS companies) required to report annually on Form EIA-28. Financial information is reported by major lines of business, including oil and gas production, petroleum refining and marketing, and other energy operations. Domestic and international operations are examined separately in this report. The data are presented in the context of key energy market developments with a view toward identifying changing strategies of corporate development and measuring the apparent success of current ongoing operations

  4. Performance profiles of major energy producers 1989

    Energy Technology Data Exchange (ETDEWEB)

    1991-01-23

    Performance Profiles of Major Energy Producers 1989 is the thirteenth annual report of the Energy Information Administration's (EIA) Financial Reporting System (FRS). The report examines financial and operating developments, with particular reference to the 23 major energy companies (the FRS companies'') required to report annually on Form EIA-28. Financial information is reported by major lines of business including oil and gas production, petroleum refining and marketing, and other energy operations. Domestic and international operations are examined separately in this report. It also traces key developments affecting the financial performance of major energy companies in 1989, as well as review of important trends.

  5. Performance profiles of major energy producers, 1991

    International Nuclear Information System (INIS)

    1992-01-01

    Performance Profiles of Major Energy Producers 1991 is the fifteenth annual report of the Energy Information Administration's (EIA) Financial Reporting System (FRS). The report examines financial and operating developments, with particular reference to the 23 major energy companies (the FRS companies) required to report annually on Form EIA-28. It also traces key developments affecting the financial performance of major energy companies in 1991, as well as reviews important trends. Financial information is reported by major lines of business including oil and gas production, petroleum refining and marketing, and other energy operations. Domestic and international operations are examined separately in this report

  6. Production of syngas and oil at biomass refinery and their application in low speed two stroke engines for combined cycle electric energy generation

    Energy Technology Data Exchange (ETDEWEB)

    Pinatti, Daltro Garcia [Universidade do Sul de Santa Catarina (UNISUL), Tubarao, SC (Brazil)], E-mail: pinatti@demar.eel.usp.br; Oliveira, Isaias de; Ferreira, Joao Carlos; Romao, Erica Leonor [RM Materiais Refratarios Ltd., Lorena, SP (Brazil)], Emails: isaias@rm-gpc.com.br, joaocarlos@rm-gpc.com.br, ericaromao@rm-gpc.com.br; Conte, Rosa Ana [University of Sao Paulo (DEMAR/EEL/USP), SP (Brazil). Lorena School of Engineering. Dept. of Materials Engineering], E-mail: rosaconte@demar.eel.usp.br

    2009-07-01

    Low speed two stroke engines burn fuels of medium quality with high efficiency (47%) and allows a flexible use of oil (> 8% of total power) and syngas (< 92%, low heating value-LHV>11.2MJ/m{sup 3}). Biomass refinery (BR) generates oil from sludge and oleaginous biomass by low temperature conversion and syngas from lignocellulosic biomass treated by diluted acidic prehydrolysis. BR has low investment cost (US$1,500.00/kW) compared with hydroelectric plants (US$2,500.00/kW) and both generate electric energy with sales price below US$75.00/MWh. It allows distributed generation from 30 MW up to 170 MW or centralized power of 1 GW with six motor generator sets. BR matrix, mass and energy balance, fuels compositions, modulations and scope of supply will be presented. Besides electric energy BR can be tailored to supply other products such as ethanol, H{sub 2} for fuel cells, biodiesel, fertilizer recycling, char and simultaneously maximizes the production of animal protein. (author)

  7. The miraculously saved refineries

    International Nuclear Information System (INIS)

    Cosnard, D.

    2005-01-01

    During 20 years, refining has been the weak link of the petroleum industry. This sector has always suffered from a chronical overcapacity. Today, on the contrary, there is a lack of facilities and shortage is threatening. The Reichstett refinery (Alsace, France) is the smallest French refinery. It has been several times threatened with closure but today, thanks to the increasing demand, it works at full capacity. This short paper summarizes the history of this facility and its social and environmental impact in the region. (J.S.)

  8. Performance profiles of major energy producers 1993

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-01-01

    Performance Profiles of Major Energy Producers 1993 is the seventeenth annual report of the Energy Information Administration`s (EIA) Financial Reporting System (FRS). The report examines financial and operating developments in energy markets, with particular reference to the 25 major US energy companies required to report annually on Form EIA-28. Financial information is reported by major liens of business, including oil and gas production, petroleum refining and marketing, other energy operations, and nonenergy businesses. Financial and operating results are presented in the context of energy market developments with a view toward identifying changing corporate strategies and measuring the performance of ongoing operations both in the US and abroad. This year`s report analyzes financial and operating developments for 1993 (Part 1: Developments in 1993) and also reviews key developments during the 20 years following the Arab Oil Embargo of 1973--1974 (Part 2: Major Energy Company Strategies Since the Arab Oil Embargo). 49 figs., 104 tabs.

  9. Report on basic survey project for promoting joint implementation in 1999. Feasibility study on energy conservation and reduction of CO2 emission at Balikpapan Refinery

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective of implementation as the clean development mechanism (CDM), a survey was performed on energy conservation and CO2 reduction at Balikpapan Refinery in Indonesia with respect to reducing emission of greenhouse effect gases. A crude oil atmospheric distillation unit with a capacity of 200,000 BPSD, and a vacuum distillation unit with a capacity of 81,000 BPSD are in operation, which emit carbon dioxide of about 470,000 tons annually from fuels burned and consumed by these units. The result of the survey revealed that there is a room for improvement in heat recovery, and that these units are separated into two groups located far away with each other in distance, resulting in low thermal efficiency and wastes in fuel. Increase in heat recovery should be achieved, and fuel consumption in the heating furnace should be reduced. Energy saving technologies owned by JGC were applied to establish a modification plan. The plan calls for maximum annual reduction of carbon dioxide of about 61,000 tons at a reduction rate of 13%, and maximum annual fuel conservation of 190 times 10{sup 9} kcal at a saving rate of 13%. PERTAMINA also desires the realization thereof if technical and financial assistance is made available. The project has a significance that it would give a great impetus to the entire regions and industries. (NEDO)

  10. Methanol production from eucalyptus wood chips. Attachment III. Florida's eucalyptus energy farm and methanol refinery: the background environment

    Energy Technology Data Exchange (ETDEWEB)

    Fishkind, H.H.

    1982-04-01

    A wide array of general background information is presented on the Central Florida area in which the eucalyptus energy plantation and methanol refinery will be located. Five counties in Central Florida may be affected by the project, DeSoto, Hardee, Hillsborough, Manatee, and Polk. The human resources of the area are reviewed. Included are overviews of population demographic and economic trends. Land use patterns and the transportation are system described, and the region's archeological and recreational resources are evaluated. The region's air quality is emphasized. The overall climate is described along with noise and air shed properties. An analysis of the region's water resources is included. Ground water is discussed first followed by an analysis of surface water. Then the overall quality and water supply/demand balance for the area is evaluated. An overview of the region's biota is presented. Included here are discussions of the general ecosystems in Central Florida, and an analysis of areas with important biological significance. Finally, land resources are examined.

  11. Performance profiles of major energy producers 1992

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-13

    Performance Profiles of Major Energy Producers 1992 is the sixteenth annual report of the Energy Information Administration`s (EIA) Financial Reporting System (FRS). The report examines financial and operating developments, with particular reference to the 25 major energy companies (the FRS companies) required to report annually on Form EIA-28. Financial information is reported by major lines of business, including oil and gas production, petroleum refining and marketing, and other energy operations. Domestic and international operations are examined separately in this report. The data are presented in the context of key energy market developments with a view toward identifying changing strategies of corporate development and measuring the apparent success of current ongoing operations.

  12. Renewable Energy Country Profiles. Latin America

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-06-15

    The IRENA Renewable Energy Country Profiles combine elements of IRENA analysis with the latest information available from a vast array of sources in order to give a brief yet comprehensive and up-to-date picture of the situation of renewable energy that includes energy supply, electrical capacity, energy access, policies, targets, investment climate, projects and endowment in renewable energy resources. Because of the different timelines of these sources, data presented here refer to years between 2009 and 2012. Data availability also differs from country to country, which makes comparison with a wider regional group possible only for the year for which figures are available for all the members of the group; while this may not be the most recent year, the differences between countries, regions and the world remain striking. The current country profiles are just a starting point; they will be extended upon with new indicators to make them more informative, and maintained as a live product on the IRENA website as a key source of information on renewable energy.

  13. FY 2000 survey report on the project on energy conservation/environmental preservation for oil corporations in Croatia by rehabilitation of oil refinery; 2000 nendo Croatia sekiyu kosha muke seiyusho no rihabiri ni yoru shene kankyo hozen project chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of strengthening the international competitive force in the oil industry of Croatia and reducing greenhouse effect gas by introducing energy conservation technology, study was made of the rehabilitation of oil refineries (Rijeka and Sisak) of Croatia's oil corporation, INDUSTRIJA NAFTE d.d. (INA). Rijeka and Sisak Refineries have the oil processing capacity of 6 million t/y and 4.6 million t/y, respectively, but they were constructed during the 1960s-1970s and are now superannuated. In this project, the following are adopted: heightening of the temperature of raw material supply, surging avoidance control, reutilization of condensate water of vacuum distillation, heightening of MEA concentration, control of excess air ratio in heating furnace, preheating of combustion air in heating furnace, application of small-diameter pump impeller, the optimum control of steam/electric system, heightening of temperature of cleaning water of desalting device, stop of adoption of flare seal gas, etc. The energy conservation effect to be expected from the project is 43,065 toe/y in a total of the two refineries, and the reduction in greenhouse effect gas is 133,000 t-CO2/y. Further, the internal return rate is 53.12%, which is very attractive for INA. (NEDO)

  14. FY 2000 report on the potential survey of implementation of a model project for improvement of thermal efficiency and energy conservation in refineries of Indonesia; 2000 nendo chosa hokokusho. Indonesia ni okeru seiyujo netsukoritsu kojo shoenergy model jigyo jisshi kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    For the purpose of heightening the thermal efficiency in oil refineries in Indonesia, survey was conducted of two main refineries of Pertamina (Cilacap Refinery and Balikpapan Refinery), and a potentiality of spreading energy conservation technology was studied. As a result of the study, the following were found out. In Cilacap Refinery, there is a possibility of energy conservation by enhancing the efficiency of the atmospheric distillation system and rationalizing utility facilities. As to Balikpapan Refinery, when effects of energy conservation are calculated by effectively using the by-producing off-gas emitted from the oil refining process which was recovered as on-site fuel, the amount of reduction in fuel consumption became 2.3 KL-FOE/h, and the year of simple investment recovery 1.7 years. Further, by recovering/effectively using hydrogen in the separation gas emitted from the hydrocracking unit, fuel/raw material in the hydrogen producing facilities were reduced, and the energy conservation effect became 2.98 KL-FOE/h in the amount of reduction in fuel consumption and 2.9 years in the year of simple investment recovery. (NEDO)

  15. Maximizing petrochemicals from refineries

    Energy Technology Data Exchange (ETDEWEB)

    Glover, B.; Foley, T.; Frey, S. [UOP, Des Plaines, IL (United States)

    2007-07-01

    New fuel quality requirements and high growth rates for petrochemicals are providing both challenges and opportunities for refineries. A key challenge in refineries today is to improve of the value of the products from the FCC unit. In particular, light FCC naphtha and LCO are prime candidates for improved utilization. Processing options have been developed focusing on new opportunities for these traditional fuel components. The Total Petrochemicals/UOP Olefin Cracking Process cracks C4-C8 olefins to produce propylene and ethylene. This process can be integrated into FCC units running at all severity levels to produce valuable light olefins while reducing the olefin content of the light FCC naphtha. Integration of the Olefin Cracking Process with an FCC unit can be accomplished to allow a range of operating modes which can accommodate changing demand for propylene, cracked naphtha and alkylate. Other processes developed by UOP allow for upgrading LCO into a range of products including petrochemical grade xylenes, benzene, high cetane diesel and low sulfur high octane gasoline. Various processing options are available which allow the products from LCO conversion to be adjusted based on the needs and opportunities of an individual refinery, as well as the external petrochemical demand cycles. This presentation will examine recent refining and petrochemical trends and highlight new process technologies that can be used to generate additional revenue from petrochemical production while addressing evolving clean fuel demands. (orig.)

  16. Performance profiles of major energy producers, 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-01-01

    The energy industry generally and petroleum and natural gas operations in particular are frequently reacting to a variety of unsettling forces. Falling oil prices, economic upswings, currency devaluations, increasingly rigorous environmental quality standards, deregulation of electricity markets, and continued advances in exploration and production technology were among the challenges and opportunities to the industry in 1997. To analyze the extent to which these and other developments have affected energy industry financial and operating performance, strategies, and industry structure, the Energy Information Administration (EIA) maintains the Financial Reporting Systems (FRS). Through Form EIA-28, major US energy companies annually report to the FRS. Financial and operating information is reported by major lines of business, including oil and gas production (upstream), petroleum refining and marketing (downstream), other energy operations, and nonenergy business. Performance Profiles of Major Producers 1997 examines the interplays of energy markets, companies` strategies, and government policies (in 1997 and in historical context) that gave rise to the results given here. The report also analyzes other key aspects of energy company financial performance as seen through the multifaceted lens provided by the FRS data and complementary data for industry overall. 41 figs., 77 tabs.

  17. The greenhouse gas emissions and fossil energy requirement of bioplastics from cradle to gate of a biomass refinery.

    Science.gov (United States)

    Yu, Jian; Chen, Lilian X L

    2008-09-15

    Polyhydroxyalkanoates (PHA) are promising eco-friendly bioplastics that can be produced from cellulosic ethanol biorefineries as value-added coproducts. A cradle-to-factory-gate life cycle assessment is performed with two important categories: the greenhouse gas (GHG)emissions and fossil energy requirement per kg of bioplastics produced. The analysis indicates that PHA bioplastics contribute clearly to the goal of mitigating GHG emissions with only 0.49 kg CO(2-e) being emitted from production of 1 kg of resin. Compared with 2-3 kg CO(2-e) of petrochemical counterparts, it is about 80% reduction of the global warming potential. The fossil energy requirement per kg of bioplastics is 44 MJ, lowerthan those of petrochemical counterparts (78-88 MJ/kg resin). About 62% of fossil energy is used for processing utilities and wastewater treatment, and the rest is required for raw materials in different life cycle stages.

  18. Refinery Upgrading of Hydropyrolysis Oil From Biomass

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, Michael [Gas Technology Inst., Des Plaines, IL (United States); Marker, Terry [Gas Technology Inst., Des Plaines, IL (United States); Ortiz-Toral, Pedro [Gas Technology Inst., Des Plaines, IL (United States); Linck, Martin [Gas Technology Inst., Des Plaines, IL (United States); Felix, Larry [Gas Technology Inst., Des Plaines, IL (United States); Wangerow, Jim [Gas Technology Inst., Des Plaines, IL (United States); Swanson, Dan [Gas Technology Inst., Des Plaines, IL (United States); McLeod, Celeste [CRI Catalyst, Houston, TX (United States); Del Paggio, Alan [CRI Catalyst, Houston, TX (United States); Urade, Vikrant [CRI Catalyst, Houston, TX (United States); Rao, Madhusudhan [CRI Catalyst, Houston, TX (United States); Narasimhan, Laxmi [CRI Catalyst, Houston, TX (United States); Gephart, John [Johnson Timber, Hayward, WI (United States); Starr, Jack [Cargill, Wayzata, MN (United States); Hahn, John [Cargill, Wayzata, MN (United States); Stover, Daniel [Cargill, Wayzata, MN (United States); Parrish, Martin [Valero, San Antonio, TX (United States); Maxey, Carl [Valero, San Antonio, TX (United States); Shonnard, David [MTU, Friedrichshafen (Germany); Handler, Robert [MTU, Friedrichshafen (Germany); Fan, Jiquig [MTU, Friedrichshafen (Germany)

    2015-08-31

    Cellulosic and woody biomass can be converted to bio-oils containing less than 10% oxygen by a hydropyrolysis process. Hydropyrolysis is the first step in Gas Technology Institute’s (GTI) integrated Hydropyrolysis and Hydroconversion IH2®. These intermediate bio-oils can then be converted to drop-in hydrocarbon fuels using existing refinery hydrotreating equipment to make hydrocarbon blending components, which are fully compatible with existing fuels. Alternatively, cellulosic or woody biomass can directly be converted into drop-in hydrocarbon fuels containing less than 0.4% oxygen using the IH2 process located adjacent to a refinery or ethanol production facility. Many US oil refineries are actually located near biomass resources and are a logical location for a biomass to transportation fuel conversion process. The goal of this project was to work directly with an oil refinery partner, to determine the most attractive route and location for conversion of biorenewables to drop in fuels in their refinery and ethanol production network. Valero Energy Company, through its subsidiaries, has 12 US oil refineries and 11 ethanol production facilities, making them an ideal partner for this analysis. Valero is also part of a 50- 50 joint venture with Darling Ingredients called Diamond Green Diesel. Diamond Green Diesel’s production capacity is approximately 11,000 barrels per day of renewable diesel. The plant is located adjacent to Valero’s St Charles, Louisiana Refinery and converts recycled animal fats, used cooking oil, and waste corn oil into renewable diesel. This is the largest renewable diesel plant in the U.S. and has successfully operated for over 2 years For this project, 25 liters of hydropyrolysis oil from wood and 25 liters of hydropyrolysis oils from corn stover were produced. The hydropyrolysis oil produced had 4-10% oxygen. Metallurgical testing of hydropyrolysis liquids was completed by Oak Ridge National Laboratories (Oak Ridge) and showed the

  19. FY 1999 report on basic survey project for joint implementations, etc. Feasibility study on energy conservation at Norsi Refinery

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This project is to link in the future to COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change) joint implementations, etc. Taken up in this survey are a topping unit, vacuum distillation unit, catalytic reforming unit, and a middle cut desulfurization unit. The purpose of the refurbishment is to conserve energy. It is estimated that 48000 TOE/year of energy will be saved and that there will be a 1.2-million tons-CO2/year reduction in greenhouse gas emissions. It is predicted that an amount equivalent to 1.3% of Russia's 1997 oil consumption will be saved across Russia and that there will be a greenhouse gas reduction equivalent to 8.8% of what Japan plans to reduce. The main problem to solve before execution of this project is in the raising of funds. Although Russia hopes that Japan will invest in the project, such at the present stage will be a high-risk venture now that the Russian economic situation and the details (CO2 emission trading, etc.) of its joint implementation framework are not yet definite. The reasonable way for Japan to follow will be to support Russia as a buyer using credits with Russia acting as the principle party. (NEDO)

  20. FY 1999 report on basic survey project for joint implementations, etc. Feasibility study on energy conservation at Norsi Refinery

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This project is to link in the future to COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change) joint implementations, etc. Taken up in this survey are a topping unit, vacuum distillation unit, catalytic reforming unit, and a middle cut desulfurization unit. The purpose of the refurbishment is to conserve energy. It is estimated that 48000 TOE/year of energy will be saved and that there will be a 1.2-million tons-CO2/year reduction in greenhouse gas emissions. It is predicted that an amount equivalent to 1.3% of Russia's 1997 oil consumption will be saved across Russia and that there will be a greenhouse gas reduction equivalent to 8.8% of what Japan plans to reduce. The main problem to solve before execution of this project is in the raising of funds. Although Russia hopes that Japan will invest in the project, such at the present stage will be a high-risk venture now that the Russian economic situation and the details (CO2 emission trading, etc.) of its joint implementation framework are not yet definite. The reasonable way for Japan to follow will be to support Russia as a buyer using credits with Russia acting as the principle party. (NEDO)

  1. Oil refining in a CO2 constrained world: Effects of carbon pricing on refineries globally

    International Nuclear Information System (INIS)

    Abdul-Manan, Amir F.N.; Arfaj, Abdullah; Babiker, Hassan

    2017-01-01

    Six aggregated refinery linear programming (LP) models were developed to represent actual refineries in North America, Latin America, Europe (including the CIS), Middle East, Asia (excluding China) and China. The models were used to conduct regional comparative assessments and to evaluate the effects of carbon pricing on refinery operations globally. We found that the average refinery energy efficiencies for the regions were estimated to range from 92.2% to 95.2%. The well-to-refinery gate carbon intensities for gasoline, diesel and jet fuels were estimated to be 17.1 (16.4–19.4), 13.3 (12.5–14.2) and 10.1 (9.6–10.8) gCO2eq/MJ, respectively. If refineries are forced to at least meet the 2014 regional volume demands for oil products, pricing CO 2 would not have an impact on either refinery productions, efficiency or emissions. If refineries are allowed to re-optimize production slates to reduce CO 2 emissions, refineries would opt to increase gasoline yield at the expense of diesel. This is counter intuitive since gasoline has a higher carbon intensity than diesel. The refinery bias against dieselization creates a supply preference toward a less efficient transportation end use. Here, we argue that if carbon pricing is not administered properly, this can lead to emissions leakage from refineries to the road transport sector. - Highlights: • Investigate actual refinery productions in 6 regions globally. • Refineries already operate at the most efficient levels. • Complex refineries tolerate higher CO 2 prices better. • Carbon pricing induces bias against dieselization. • Identify potential emissions leakage.

  2. Kvanefjeld refinery pilot plant operations

    International Nuclear Information System (INIS)

    Krebs, Damien; Furfaro, Domenic

    2016-01-01

    Greenland Minerals and Energy is a junior project development company which is listed on the Australian Stock Exchange (asx:GGG). It is developing the Kvanefjeld rare earth and uranium project located in the southern tip of Greenland. The project has completed a Feasibility Study and is currently in the permitting phase. Last year was a busy time for the company as it completed a Feasibility Study, a mining licence application (draft submitted in December 2015) and pilot plant operations. Beneficiation pilot plant operations were completed at GTK in Finland in April 2015. This pilot plant treated approximately 30 tonnes of ore to producing almost 2 tonnes of rare earth mineral concentrate. Later in the year a hydrometallurgical pilot plant was performed which mimicked the Refinery process. This pilot plant was performed at Outotec’s Pori Research laboratories in Finland from September till October 2015. The pilot plant treated approximately 200 kilograms of concentrate over 4 split operating campaigns. Each campaign was performed to focus on the performance of a specific part of the refinery flowsheet. This allowed for full operating focus on a single unit operation to ensure that it was operating correctly. The pilot plant operations were quite successful with no major issues with the flowsheet identified through continuous operation. Some fine tuning of conditions was required to ensure adequate removal of impurities was performed with recycle streams incorporated. Overall the leach extractions observed in the pilot plant exceeded the design assumptions in the Feasibility Study. These programs were partially funded by the EURARE program. The EURARE program aims to encourage the sustainable development of European based rare earth projects. This has the goal of allowing Europe to become less reliant on importation of these key raw materials. The professionalism and performance of both GTK and Outotec contributed significantly to the success of the pilot plant

  3. World Energy Data System (WENDS). Volume VI. International agreement profiles

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-06-01

    The World Energy Data System contains organized data on those countries and international organizations that may have critical impact on world energy. The international agreement profiles in WENDS are all energy-related and are organized by energy technology. These are: coal; conservation; fusion; geothermal; nuclear fission; oil, gas, and shale; solar, wind, and ocean thermal; and other (cooperation in electrical power equipment acquisition, energy, energy research, etc.). The agreement profiles are accessible by energy technology and alphabetically by country.

  4. Energy infrastructure in India: Profile and risks under climate change

    International Nuclear Information System (INIS)

    Garg, Amit; Naswa, Prakriti; Shukla, P.R.

    2015-01-01

    India has committed large investments to energy infrastructure assets-power plants, refineries, energy ports, pipelines, roads, railways, etc. The coastal infrastructure being developed to meet the rising energy imports is vulnerable to climate extremes. This paper provides an overview of climate risks to energy infrastructures in India and details two case studies – a crude oil importing port and a western coast railway transporting coal. The climate vulnerability of the port has been mapped using an index while that of the railway has been done through a damage function for RCP 4.5.0 and 8.5 scenarios. Our analysis shows that risk management through adaptation is likely to be very expensive. The system risks can be even greater and might adversely affect energy security and access objectives. Aligning sustainable development and climate adaptation measures can deliver substantial co-benefits. The key policy recommendations include: i) mandatory vulnerability assessment to future climate risks for energy infrastructures; ii) project and systemic risks in the vulnerability index; iii) adaptation funds for unmitigated climate risks; iv) continuous monitoring of climatic parameters and implementation of adaptation measures, and iv) sustainability actions along energy infrastructures that enhance climate resilience and simultaneously deliver co-benefits to local agents. -- Highlights: •Climate risks to energy infrastructures adversely impact energy security. •Case studies of a port and a railway show their future climate change vulnerability. •Managing climate-induced risks through preventive adaptation policies

  5. Fiscal 1999 research report. Basic research for promotion of joint implementation programs (Energy efficiency survey at Noboil Refinery of Ufa City); 1999 nendo Ufa shi Noboil seiyusho ni kansuru sho energy chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The aim is to explore projects that will lead to joint implementations for greenhouse gas emission reduction, and a survey was conducted at the Bashneftechim Refineries, Ufa City, Bashkir Republic, Russian Federation. A feasibility study was carried out involving energy efficiency improvement for oil refining related units such as atmospheric and vacuum distillators. In the energy efficiency survey, studies covered energy efficiency improvement in the existing equipment through the modification of the normal and vacuum distillators, visbreaker, vacuum desulfurizer for light oil, and the process heating furnace of the catalytic cracking equipment, for a reduction in fuel consumption by realizing combustion excess air ratio control; the installation of an air preheater or a waste heater boiler for the collection of heat from combustion exhaust gas; the addition of heat exchangers and the optimization of their arrangement for an increase in the amount of heat recoverable from hot oil; the replacement of obsolete instruments and controllers with state-of-the-art types for higher energy efficiency in the control of distillation tower operation, etc. It is desired that this energy saving project will be embodied for a reduction in CO2 emissions. (NEDO)

  6. Influence of ownership capital structure of Refinery's operation and development

    International Nuclear Information System (INIS)

    Hadzhi-Mishev, Dimitar

    1999-01-01

    Refineries are part of the energetic infrastructure of one country. Their significance is dependent on the geographic country position (whether it has sea exit or not), and on structure of primary energy spends in the country. According these facts, country's attitude to the refineries on its territory could be different. The possibility of ownership structure transformation in refineries and necessary legislation in the energetic sector of the state, needed for transformation realization are analyzed in this paper. Essential conditions for transformation fulfilling are protection 'mechanisms for domestic production in crude oil economy, manners of crude oil products price defining, and manners of excise determination and payment. As a function of these conditions, the conditions under which transformation of ownership structure in refineries is possible, as well as their influence on the operation and development of this part of energetic structure in transition country are defined in this paper. (Original)

  7. Integrated refinery waste management

    Energy Technology Data Exchange (ETDEWEB)

    Shieh, Y -S [ETG Environmental, Inc., Blue Bell, PA (US); Sheehan, W J [Separation and Recovery Systems, Inc., Irvine, CA (US)

    1992-01-01

    In response to the RCRA land ban regulations and TC rule promulgated by the U.S. Federal Environmental Protection Agency (EPA) in 1988-1990, an Integrated Refinery Waste Management (IRWM) program has been developed to provide cost-effective solutions to petroleum industry customers. The goal of IRWM is to provide technology based remediation treatment services to manage sludges and wastewaters generated from the oil refining processes, soils contaminated with petroleum distillates and groundwater contaminated with fuels. Resource recovery, volume reduction and waste minimization are the primary choices to mitigate environmental problems. Oil recovery has been performed through phase separation (such as centrifugation and filtration) and heating of heavy oils. Volume reduction is achieved by dewatering systems such as centrifuges and filter presses, and low temperature thermal treatment. Waste minimization can be accomplished by bioremediation and resource recovery through a cement kiln. (Author).

  8. Fiscal 1999 report. Basic research for promotion of joint implementation programs (Basic research on energy saving at Tehran Oil Refinery); 1999 nendo Tehran seiyusho ni kansuru sho energy chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    An energy saving survey was conducted for the oil refining equipment of the Tehran Oil Refinery, Islamic Republic of Iran, for the prevention of global warming due to greenhouse gas emissions. Examined were an atmospheric pressure distiller, vacuum distiller, vis breaker, naphtha hydrodesulfurizer and naphtha catalytic modifier, light oil vacuum hydrocracker, hydrogen producing unit, asphalt producing unit, boiler facilities, etc., which had all been augmented in 1974. According to the energy saving modification scheme, energy efficiency improvement will be achieved by fully utilizing the existing facilities but not by replacing them all. The outcome of a feasibility study predicts that flue gas O2 control will take approximately a year for completion and main modification programs will take approximately 3-5 years for completion. The total investment required is estimated at approximately 1.5-billion yen, and the sum of fuel to be saved is estimated at approximately 0.6-billion yen/year. As for CO2 reduction, approximately 260-thousand tons/year is expected against the baseline of approximately 1380-thousand tons/year. (NEDO)

  9. Fiscal 1999 basic survey report for promotion of joint implementation. Study on energy saving and CO2 reduction at Balikpapan refinery; 1999 nendo Balikpapan seiyusho ni okeru shoene CO{sub 2} sakugen chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Concerning the reduction of greenhouse gas emissions for the embodiment of clean development mechanisms (CDMs) in Indonesia, a survey is conducted about energy saving and CO2 reduction at its Balikpapan refinery. At the refinery, a crude-oil atmospheric distillation unit operates at 200,000 BPSD (barrels per stream day) and a vacuum distillation unit at 81,000 BPSD, with the fuel consumed by the two units discharging approximately 470,000 tons/year of CO2. The result of the survey discloses that there is need for some improvement in relation with heat recovery and that the great distance between the two distillation units presents a problem in relation with heat efficiency. To settle the problems, heat recovery will be enhanced and the fuel to be burned in the heating furnace will be reduced. A plan to modify the heat exchanger system is worked out using JGC Corporation's energy-saving technology, and a rough design is drafted for the modification. When the modification is carried out, there will be a CO2 reduction of 18,636-61,597 tons/year. The Pertamina also wants the plan to be realized, wishing that technical and financial aids will be available. The plan when realized will serve as a stimulus to the local community and to the industry as a whole. (NEDO)

  10. Economic forces push down selling prices of U.S. refineries

    International Nuclear Information System (INIS)

    Anon.

    1996-01-01

    Recent data on US refinery sales reveal that selling prices have continued to decline in the 1990s. Reasons for this decrease include increased plant investments to meet regulatory requirements, excess refining capacity, increased imports of refined products, and reduced margins. While these expenditures enable a refinery to continue operating, they do not make the refinery more profitable or valuable. Other factors contributing to reduced selling prices of US refineries are: declining local crude production; unstable crude costs; increased energy conservation; growing competition from alternative fuels

  11. Thermodynamic simulation and evaluation of sugar refinery evaporators using a steady state modelling approach

    International Nuclear Information System (INIS)

    Lewis, A.E.; Khodabocus, F.; Dhokun, V.; Khalife, M.

    2010-01-01

    In a sugar refinery, the juice is concentrated through evaporation, with the objective of concentrating the juice to syrup as rapidly as possible. Because the heat of vaporization of water is relatively high, the evaporation process can be highly energy intensive, and therefore the economical use of steam is important in the refinery. This paper reports on the development of a simulation model for the evaporation sections of two Mauritian sugar refineries. The first objective was to use the simulation model to carry out an energy balance over the evaporators in order to assess the economy of steam usage over the refinery. The second objective was to examine to what extent a fundamental steady state model, based on thermodynamics (not kinetics) was capable of predicting the material and energy flows in two operating sugar refineries and thereby to evaluate the applicability of the modelling framework. The simulation model was validated using historical data as well as data from the plant DCS system. The simulation results generally correlated well with the measured values, except for one of the evaporators on one refinery. Some suggestions were made as to the cause of the discrepancy. On balance, it was found that both refineries are extremely efficient in terms of steam and equipment usage and that there is not much scope for energy optimisation within the present configuration - nor for much spare steam capacity for an additional refinery. It was also shown that steady state process simulation, using thermodynamic models, can generate a very useful representation of a working refinery. Besides being able to use the model to 'benchmark' the operation and thus evaluate its performance as a whole as well as across individual units, it could also be used to evaluate refinery performance across refineries, nationally as well as globally.

  12. Solar energy in Australia: a profile of renewable energy activity in its national context

    Energy Technology Data Exchange (ETDEWEB)

    Case, G.L.

    1980-08-01

    The following topics are included: country overview; energy summary; geopolitical, economic, and cultural aspects of Australia; the energy profile; and international agreements, contacts, manufacturers, and projects. (MHR)

  13. An estimation of cogeneration potential by using refinery residuals in Mexico

    International Nuclear Information System (INIS)

    Marin-Sanchez, J.E.; Rodriguez-Toral, M.A.

    2007-01-01

    Electric power generation in Mexico is mainly based on fossil fuels, specifically heavy fuel oil, although the use of natural gas combined cycles (NGCC) is becoming increasingly important. This is the main destination that has promoted growing imports of natural gas, currently accounting for about 20% of the total national annual consumption. Available crude oil is becoming heavier; thus refineries should be able to process it, and to handle greater quantities of refinery residuals. If all refinery residuals are used in cogeneration plants serving petroleum refineries, the high heat/power ratio of refinery needs, leads to the availability of appreciable quantities of electricity that can be exported to the public utility. Thus, in a global perspective, Mexican imports of natural gas may be reduced by cogeneration using refinery residuals. This is not the authors' idea; in fact, PEMEX, the national oil company, has been entitled by the Mexican congress to sell its power leftovers to The Federal Electricity Commission (CFE) in order to use cogeneration in the way described for the years to come. A systematic way of determining the cogeneration potential by using refinery residuals from Mexican refineries is presented here, taking into account residual quantities and composition, from a national perspective, considering expected scenarios for Maya crude content going to local refineries in the years to come. Among different available technologies for cogeneration using refinery residuals, it is believed that the integrated gasification combined cycle (IGCC) would be the best option. Thus, considering IGCC plants supplying heat and power to refineries where it is projected to have refinery residuals for cogeneration, the expected electric power that can be sent to the public utility is quantified, along with the natural gas imports mitigation that may be attained. This in turn would contribute to a necessary fuel diversification policy balancing energy, economy and

  14. Fiscal 1999 research report. Basic research for promotion of joint implementation programs (Research on energy saving plan for NORSI Refinery); 1999 nendo NORSI seiyusho sho energy keikaku chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This is a feasibility study desired to connect to a joint implementation program in the future, which plans to modify the oil refining system now in existence at the NORSI Refinery in the Russian Federation. The modification plan for energy efficiency improvement consists of (1) the reconstruction of the heat exchanger network, addition of three high-efficiency heating furnaces, and the introduction of stripping steam into the pre-distillation tower for the atmospheric/vacuum distillation system, (2) the addition of two combined heat exchangers, replacement of the reboiler with a steam reboiler, and the use of reflux line in the deethanization tower for the reforming section of the catalytic reforming unit, and (3) the addition of combined heat exchangers and the installation of two high-efficiency heater furnaces for the hydrodesulfurization unit for kerosene and light oil. The plan requires 40,470,000 dollars, and will save 48,000 tons/year in terms of oil and reduce CO2 emissions by 120,000 tons/year. No settlement has been reached, however, about financing, agreement to cost performance, or apportioning of the amount of reduction in CO2 emissions to the parties involved in case of transfer under a joint implementation program. It is desired that these problems will be solved for the promotion of the project. (NEDO)

  15. Energy in Mexico: a profile of solar energy activity in its national context

    Energy Technology Data Exchange (ETDEWEB)

    Hawkins, D.

    1980-04-01

    The geopolitical, economic, and cultural aspects of the United States of Mexico are presented. Mexico's energy profile includes the following: energy policy objectives, government energy structure, organizations for implementation, indigeneous energy sources, imported energy sources, solar energy research and development, solar energy organizations and solar energy related legislation and administrative policies. International agreements, contacts, manufacturers, and projects are listed. (MRH)

  16. National energy data profile - Brazil 2004

    International Nuclear Information System (INIS)

    2004-01-01

    This report presents a more detailed study on the chances of further developing the clean brazilian energy matrix up to the year of 2030. The report intends to discuss the options compatible with Brazilian energy resources and existing viable technologies. The report also forecasts data on energy up to the year of 2030, concerned to the fields of energy supply, processing sector and demand

  17. National energy data profile, Austria 1992

    International Nuclear Information System (INIS)

    1993-12-01

    Detail information about the energy consumption, energy demand and supply, general features of energy economy and the analysis of the development of energy economy in Austria in 1992 as well as preliminary data on energy consumption in the first 6 months of 1993 is given. Statistical data about the development of energy demand by sectors, development of total final energy demand by energy carriers (articulated in coal, refined petroleum products, natural gas, other, electricity and heat), development of energy consumption in industry (articulated in coal, refined petroleum products, natural gas, other, electricity and heat) and development of energy consumption of domestic consumers (articulated in coal, refined petroleum products, natural gas, other, electricity and heat) is shown. Graphical data about (1) primary energy supply by source, (2) primary energy, economic activity and electricity, (3) indigenous energy production, (4) conventional energy resources, (5) electricity supply by source, (6) electricity consumption by sector is presented for the years 1970 - 1992. Data about the development and exploitable hydro-power potentials by rivers and the main sources of man-made emissions of air pollutants in Austria 1990 according to the results of the CORINE-inventory are added. (blahsl)

  18. Poland petroleum refinery sludge lagoon demonstration project

    International Nuclear Information System (INIS)

    Altman, D.J.

    2000-01-01

    The US Department of Energy and the Institute for Ecology of Industrial Area have been working together to develop mutually beneficial, cost-effective environmental remediation technologies such as the demonstration of bioremediation techniques for the clean up of acidic petroleum sludge impacted soils at an oil refinery in southern Poland. After an expedited site characterization, treatability study, and a risk assessment study, a remediation strategy was devised. The waste material was composed primarily of high molecular weight paraffinic and polynuclear aromatic hydrocarbons. A biopile design which employed a combination of passive and active aeration in conjunction with nutrient and surfactant application as used to increase the biodegradation of the contaminants of concern

  19. Benchmarking of refinery emissions performance : Executive summary

    International Nuclear Information System (INIS)

    2003-07-01

    This study was undertaken to collect emissions performance data for Canadian and comparable American refineries. The objective was to examine parameters that affect refinery air emissions performance and develop methods or correlations to normalize emissions performance. Another objective was to correlate and compare the performance of Canadian refineries to comparable American refineries. For the purpose of this study, benchmarking involved the determination of levels of emission performance that are being achieved for generic groups of facilities. A total of 20 facilities were included in the benchmarking analysis, and 74 American refinery emission correlations were developed. The recommended benchmarks, and the application of those correlations for comparison between Canadian and American refinery performance, were discussed. The benchmarks were: sulfur oxides, nitrogen oxides, carbon monoxide, particulate, volatile organic compounds, ammonia and benzene. For each refinery in Canada, benchmark emissions were developed. Several factors can explain differences in Canadian and American refinery emission performance. 4 tabs., 7 figs

  20. Performance profiles of major energy producers 1996

    International Nuclear Information System (INIS)

    1998-01-01

    This publication examines developments in the operations of the major US e energy-producing companies on a corporate level, by major line of business, by major function within each line of business, and by geographic area. In 1996, 24 companies filed Form EIA-28. The analysis and data presented in this report represents the operations of the Financial Reporting System companies in the context of their worldwide operations and in the context of the major energy markets which they serve. Both energy and nonenergy developments of these companies are analyzed. Although the focus is on developments in 1996, important trends prior to that time are also featured. Sections address energy markets in 1996; key financial developments; oil and gas exploration, development, and production; downstream petroleum in 1996; coal and alternative energy; and foreign direct investment in US energy. 30 figs., 104 tabs

  1. Performance profiles of major energy producers 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-01-01

    This publication examines developments in the operations of the major US e energy-producing companies on a corporate level, by major line of business, by major function within each line of business, and by geographic area. In 1996, 24 companies filed Form EIA-28. The analysis and data presented in this report represents the operations of the Financial Reporting System companies in the context of their worldwide operations and in the context of the major energy markets which they serve. Both energy and nonenergy developments of these companies are analyzed. Although the focus is on developments in 1996, important trends prior to that time are also featured. Sections address energy markets in 1996; key financial developments; oil and gas exploration, development, and production; downstream petroleum in 1996; coal and alternative energy; and foreign direct investment in US energy. 30 figs., 104 tabs.

  2. Comprehensive energy management eco routing & velocity profiles

    CERN Document Server

    Brandstätter, Bernhard

    2017-01-01

    The book discusses the emerging topic of comprehensive energy management in electric vehicles from the viewpoint of academia and from the industrial perspective. It provides a seamless coverage of all relevant systems and control algorithms for comprehensive energy management, their integration on a multi-core system and their reliability assurance (validation and test). Relevant European projects contributing to the evolvement of comprehensive energy management in fully electric vehicles are also included.

  3. Supporting industries energy and environmental profile

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2005-09-21

    As part of its Industries of the Future strategy, the Industrial Technologies Program within the U.S. Department of Energy’s (DOE) Office of Energy Efficiency and Renewable Energy works with energy-intensive industries to improve efficiency, reduce waste, and increase productivity. These seven Industries of the Future (IOFs) – aluminum, chemicals, forest products, glass, metal casting, mining, and steel – rely on several other so-called “supporting industries” to supply materials and processes necessary to the products that the IOFs create. The supporting industries, in many cases, also provide great opportunities for realizing energy efficiency gains in IOF processes.

  4. Residential Energy Consumption Survey: Quality Profile

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The Residential Energy Consumption Survey (RECS) is a periodic national survey that provides timely information about energy consumption and expenditures of U.S. households and about energy-related characteristics of housing units. The survey was first conducted in 1978 as the National Interim Energy Consumption Survey (NIECS), and the 1979 survey was called the Household Screener Survey. From 1980 through 1982 RECS was conducted annually. The next RECS was fielded in 1984, and since then, the survey has been undertaken at 3-year intervals. The most recent RECS was conducted in 1993.

  5. Solar energy in Italy: a profile of renewable energy activity in its national context

    Energy Technology Data Exchange (ETDEWEB)

    Shea, C.A.

    1980-12-01

    The following are included: country overview; energy summary; Italian Republic-geopolitical, economic, and cultural aspects; the energy profile; imported energy sources; solar energy research and development; solar energy organizations; solar energy related legislation and administration policies; and international agreements, contacts, manufacturers, and projects. (MHR)

  6. HERA an HTR for use in a refinery

    International Nuclear Information System (INIS)

    Chaubernard, P.

    1977-01-01

    It is shown that it was technically possible to use a High Temperature Reactor to provide a large part of the energy (process heat, steam, electricity) consumed in a refinery. Nevertheless, economic calculations have lead to a prime cost of spared crude oil twice the existing price

  7. Energy conservation in India: a profile

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    The decade and half since the oil crisis of 1973 has been a period that has witnessed a steady growth of the energy conservation ethos in India. Housekeeping and low risk conservation options have been largely preferred so far. The IMWG (Inter-Ministerial Working Group on Utilization and Conservation of Energy) study did not evaluate potential saving through the introduction of high risk and high pay-off technologies. The potential for energy conservation in India is substantial. However, some of the barriers to achieving the potential in the past have been energy prices which deviate from rational tariffs and prices, a lack of information on specific measures and of options for achieving energy conservation, paucity of capital for schemes requiring technology upgradation and efficiency improvements, and the inadequacy if institutional arrangement for promoting energy conservation in different sectors of the economy. Recent efforts pursued by several organizations however provide some basis for optimism. Given the growing capital intensity of the energy sector in India, more vigorous efforts are likely to be made in the future. In particular, success stories in some industrial units indicate that decentralized efforts by the units themselves can achieve a great deal in improving the efficiency of energy use, particularly in the Indian industry. Policies to promote such programmes would help accelerate energy conservation efforts in industrial units and in other sectors. It is therefore hoped that the intensity of energy use in several sectors of the indian economy will be reduced significantly in the coming years. (author). 3 refs., 3 tabs

  8. Refineries in Europe under pressure

    International Nuclear Information System (INIS)

    Widdershoven, C.

    2008-01-01

    Current oil price developments and the economic and financial crisis are leading to a negative situation for the European refining sector. Analysts expect that a number of European oil refineries will lower their production in the coming months as a result of decreased petrol demand. [mk] [nl

  9. Performance profiles of major energy producers 1979

    International Nuclear Information System (INIS)

    1981-07-01

    The purpose of this report is to examine year-to-year developments in the operations of 26 major US energy companies on a corporate level and also by major line of energy business and by major functions within each line of business. The period covered is 1977 to 1979. Comparisons of income and investment flow are featured and related to functionally allocated net investment in place. The presentation seeks to identify similarities and dissimilarities in results across lines-of-business activity or by firm size

  10. Risk-profile modification of energy projects

    International Nuclear Information System (INIS)

    Larson, B.O.

    1992-01-01

    The commodity futures and swaps markets are thought to be the invention of speculators, the bane of the oil business, or possibly something confined to finance departments of major corporations. In actuality, they should be considered more as an insurance vehicle and can be used at the project level to modify the risk profile of a property. In this context, an increased familiarity with them can be useful for an engineer. Either futures of swaps can be used to guarantee or modify product prices. While this does not necessarily maximize cash flow or present worth, it can protect a project or company for several years from downside price risk, thereby reducing the risk of the venture. This can be particularly important if lower product prices would cause unacceptable cash flows or net incomes. This paper reports that reducing risk by limiting downside price exposure could alter budgeting decisions, allow continued or expanded operations of a particular property, or increase debt capacity

  11. Computer Profile of School Facilities Energy Consumption.

    Science.gov (United States)

    Oswalt, Felix E.

    This document outlines a computerized management tool designed to enable building managers to identify energy consumption as related to types and uses of school facilities for the purpose of evaluating and managing the operation, maintenance, modification, and planning of new facilities. Specifically, it is expected that the statistics generated…

  12. Profiles of foreign direct investment in US energy, 1991

    International Nuclear Information System (INIS)

    1993-01-01

    Profiles of Foreign Direct Investment in US Energy 1991 describes the role of foreign ownership in US energy enterprises, with respect to investment, energy operations, and financial performance. Additionally, since energy investments are made in a global context, outward investment in energy is reviewed trough an examination of US-based companies' patterns of investment in foreign petroleum. The data used in this report come from the Energy Information Administration (EIA), the US Department of Commerce, company annual reports, and public disclosures of investment transactions

  13. Profiles of foreign direct investment in US energy, 1990

    International Nuclear Information System (INIS)

    1992-01-01

    Profiles of Foreign Direct Investment in US Energy 1990 describes the role of foreign ownership in US energy enterprises, with respect to investment, energy operations, and financial performance. Additionally, since energy investments are made in a global context, outward investment in energy is reviewed through an examination of US-based companies' patterns of investment in foreign petroleum. The data used in this report come from the Energy Information Administration (EIA), the US Department of Commerce, company annual reports, and public disclosures of investment transactions

  14. Profiles

    International Nuclear Information System (INIS)

    2004-01-01

    Profiles is a synthetic overview of more than 100 national energy markets in the world, providing insightful facts and key energy statistics. A Profile is structured around 6 main items and completed by key statistics: Ministries, public agencies, energy policy are concerned; main companies in the oil, gas, electricity and coal sectors, status, shareholders; reserve, production, imports and exports, electricity and refining capacities; deregulation of prices, subsidies, taxes; consumption trends by sector, energy market shares; main energy projects, production and consumption prospects. Statistical Profiles are present in about 3 pages the main data and indicators on oil, gas, coal and electricity. (A.L.B.)

  15. Solar energy in Argentina: A profile of renewable energy activity in its national context

    Science.gov (United States)

    Hawkins, D.

    1981-01-01

    The following subjects are covered: The country overview; the energy summary; the geopolitical, economic, and cultural aspects of the Republic of Argentina; the energy profile; and international contacts, manufacturers, and projects.

  16. Solar energy in Argentina: a profile of renewable energy activity in its national context

    Energy Technology Data Exchange (ETDEWEB)

    Hawkins, D.

    1981-01-01

    The following subjects are included: the country overview; the energy summary; the geopolitical, economic, and cultural aspects of the Republic of Argentina; the energy profile; and international contacts, manufacturers, and projects. (MHR)

  17. Radioisotope techniques for problem-solving on refineries

    International Nuclear Information System (INIS)

    Charlton, J.S.; Webb, M.

    1994-01-01

    Increasingly, refineries worldwide are recognizing the value of radioisotope technology in studying the operation of on-line plant. Using case studies, this paper illustrates the versatility of radioisotope techniques in a wide range of investigations: the density-profiling of distillation columns; the investigation of leaks on feed/effluent exchangers; on-line flowrate measurement; underground leakage detection. The economic benefits deriving from radioisotope applications are indicated

  18. Risk profile modification of energy projects

    International Nuclear Information System (INIS)

    Larson, B.O.

    1992-01-01

    The commodity futures and swaps markets are thought by some to be the invention of speculators, the bane of the oil business, or possibly something confined to finance departments of major corporations. In actuality, they should be considered more as insurance and can be utilized at the project level to modify the risk profile of a property. In this context, an increased familiarity with them can be useful for an engineer. This paper reports that either futures or swaps can be used to guarantee or modify product prices, an accomplishment very difficult or impossible to duplicate through other means, particularly with such integrity. Participation in futures or swaps does not necessarily maximize cashflow or present worth, it can either guarantee the price, put a minimum price in place or offer a combination of the above. A project or company can be protected for several years from downside price risk using swaps. Not being subject to market price swings substantially reduces the risk of the venture. This can be particularly important if lower product prices would cause unacceptable cashflows or net incomes

  19. Renewable Energy Policy Country Profiles. 2011 version

    Energy Technology Data Exchange (ETDEWEB)

    Teckenburg, E.; Rathmann, M.; Winkel, T. [ECOFYS, Utrecht (Netherlands); Ragwitz, M.; Steinhilber, S. [Fraunhofer Institute for Systems and Innovation Research ISI, Karlsruhe (Germany); Resch, G.; Panzer, C.; Busch, S. [Energy Economics Group EEG, Technical University Vienna, Vienna (Austria); Konstantinaviciute, I. [Lithuanian Energy Institute, Kaunas (Lithuania)

    2011-08-15

    The core objective of the project RE-Shaping is to assist Member State (MS) governments in preparing for the implementation of Directive 2009/28/EC and to guide a European policy for RES in the mid- to long term. The past and present success of policies for renewable energies will be evaluated and recommendations derived to improve future RES support schemes. The effectiveness and the efficiency of current and future RES support schemes is analysed with specific focus on a single European market for renewable electricity products. Current best practices are identified, and (future) costs of RES and the corresponding support necessary to initiate stable growth are assessed. Better integration of RES policies with climate and innovation policy as well as liberalised energy markets will be analysed and promoted. Options for flexibility between Member States will be analysed. The future deployment of RES in each MS will be calculated based on the Green-X model to assist MS in implementing national action plans and to support a long term vision of the European RES policy. The latter will be based on an in-depth analysis of the long term RES potentials and costs. The impact of policies on risks for RES financing will be analysed and improved policies and financing instruments will be proposed.

  20. Implantation profile of low-energy positrons in solids

    International Nuclear Information System (INIS)

    Asoka-Kumar, P.; Lynn, K.G.

    1990-01-01

    A simple form for an implantation profile of monoenergetic, low-energy (1--10 keV) positrons in solids is presented. Materials studied include aluminum, copper, molybdenum, palladium, and gold with atomic number ranging from 13 to 79. A simple set of parameters can describe the currently used Makhov profile in slow positron studies of solids. We provide curves and tables for the parameters that can be used to describe the implantation profiles of positrons in any material with atomic number in between 13 and 79

  1. Joint refinery selenium treatability study

    International Nuclear Information System (INIS)

    Meyer, C.L.; Folwarkow, S.

    1993-01-01

    The San Francisco Regional Water Quality Control Board recently established mass limits on discharges of selenium to the San Francisco Bay from several petroleum refineries. The refineries had been working independently to develop control strategies, including both source control and treatment options, for removal of selenium from their discharges. By January 1992, over fifty different combinations of treatment technologies, wastewater streams, and pretreatment steps had been investigated to determine their effectiveness and feasibility as selenium removal processes. No treatment process studied could achieve the required mass limits without serious negative environmental consequences, such as generation of large amounts of hazardous sludge. To better facilitate the development of a feasible selenium treatment process, the six Bay Area refineries shared results of their studies and identified several technologies that, with further work, could be developed further. This additional work is currently being carried out as part of a joint selenium treatability study sponsored by the Western States Petroleum Association. A review of the previous source control and treatment studies, along with a description of the current treatability studies will be discussed

  2. Global Warming Potential Of A Waste Refinery Using Enzymatic Treatment

    DEFF Research Database (Denmark)

    Tonini, Davide; Astrup, Thomas

    2010-01-01

    and fossil resources. This is especially important with respect to the residual waste (i.e. the remains after source-separation and separate collection) which is typically incinerated or landfilled. In this paper the energy and Global Warming performance of a pilot-scale waste refinery for the enzymatic...... plants and utilization of the liquid fraction for biogas production turned out to be the best options with respect to energy and Global Warming performance....

  3. Treatment and disposal of refinery sludges: Indian scenario.

    Science.gov (United States)

    Bhattacharyya, J K; Shekdar, A V

    2003-06-01

    Crude oil is a major source of energy and feedstock for petrochemicals. Oily sludge, bio-sludge and chemical sludge are the major sludges generated from the processes and effluent treatment plants of the refineries engaged in crude oil refining operations. Refineries in India generate about 28,220 tons of sludge per annum. Various types of pollutants like phenols, heavy metals, etc. are present in the sludges and they are treated as hazardous waste. Oily sludge, which is generated in much higher amount compared to other sludges, contains phenol (90-100 mg/kg), nickel (17-25 mg/kg), chromium (27-80 mg/kg), zinc (7-80 mg/kg), manganese (19-24 mg/kg), cadmium (0.8-2 mg/kg), copper (32-120 mg/kg) and lead (0.001-0.12 mg/ kg). Uncontrolled disposal practices of sludges in India cause degradation of environmental and depreciation of aesthetic quality. Environmental impact due to improper sludge management has also been identified. Salient features of various treatment and disposal practices have been discussed. Findings of a case study undertaken by the authors for Numaligarh Refinery in India have been presented. Various system alternatives have been identified for waste management in Numaligarh Refinery. A ranking exercise has been carried out to evaluate the alternatives and select the appropriate one. A detailed design of the selected waste management system has been presented.

  4. Allowance Allocation and CO2 intensity of the EU15 and Norwegian refineries

    International Nuclear Information System (INIS)

    Nilsson, Kristina; Zetterberg, Lars; Aahman, Markus

    2005-02-01

    On 1 January 2005, the European Union Emission Trading Scheme (EU ETS) was launched. The launch has been preceded by an allocation process in each of the Member States. The main objective of this study was to analyse the allocation in relation to CO 2 efficiency for the mineral oil refining sector. A CO 2 intensity index for mineral oil refineries has been defined and calculated for the refineries within the EU15 and Norway. The IVL CO 2 intensity index is based both on the Solomon Energy Intensity Index (EII), an assumed fuel mix, and process-specific emissions. Due to uncertainties in input data, the determined values for the individual refineries are quite uncertain. However, the regional values can be used to identify trends. It was concluded that there are substantial differences in the CO 2 intensity between refineries within different regions/countries in the EU and these differences have not been considered in the allocation process. Only a few countries have mentioned energy efficiency or reduction potential due to CO 2 intensity of fuels used. Only one country (Denmark) has explicitly given a benchmark that will be used for allocation to new mineral oil refineries. The allocation has generally been based on historic emissions, which will result in refineries with historically higher emissions being allocated larger amounts than refineries with historically lower emissions. This might be favourable for refineries that recently have performed emission-reducing measures but might be less favourable for refineries that during a long time period have implemented emission-reducing measures

  5. Allowance Allocation and CO{sub 2} intensity of the EU15 and Norwegian refineries

    Energy Technology Data Exchange (ETDEWEB)

    Nilsson, Kristina; Zetterberg, Lars; Aahman, Markus

    2005-02-01

    On 1 January 2005, the European Union Emission Trading Scheme (EU ETS) was launched. The launch has been preceded by an allocation process in each of the Member States. The main objective of this study was to analyse the allocation in relation to CO{sub 2} efficiency for the mineral oil refining sector. A CO{sub 2} intensity index for mineral oil refineries has been defined and calculated for the refineries within the EU15 and Norway. The IVL CO{sub 2} intensity index is based both on the Solomon Energy Intensity Index (EII), an assumed fuel mix, and process-specific emissions. Due to uncertainties in input data, the determined values for the individual refineries are quite uncertain. However, the regional values can be used to identify trends. It was concluded that there are substantial differences in the CO{sub 2} intensity between refineries within different regions/countries in the EU and these differences have not been considered in the allocation process. Only a few countries have mentioned energy efficiency or reduction potential due to CO{sub 2} intensity of fuels used. Only one country (Denmark) has explicitly given a benchmark that will be used for allocation to new mineral oil refineries. The allocation has generally been based on historic emissions, which will result in refineries with historically higher emissions being allocated larger amounts than refineries with historically lower emissions. This might be favourable for refineries that recently have performed emission-reducing measures but might be less favourable for refineries that during a long time period have implemented emission-reducing measures.

  6. Techno-Economic Evaluation of Technologies to Mitigate Greenhouse Gas Emissions at North American Refineries.

    Science.gov (United States)

    Motazedi, Kavan; Abella, Jessica P; Bergerson, Joule A

    2017-02-07

    A petroleum refinery model, Petroleum Refinery Life-cycle Inventory Model (PRELIM), that estimates energy use and CO 2 emissions was modified to evaluate the environmental and economic performance of a set of technologies to reduce CO 2 emissions at refineries. Cogeneration of heat and power (CHP), carbon capture at fluid catalytic cracker (FCC) and steam methane reformer (SMR) units, and alternative hydrogen production technologies were considered in the analysis. The results indicate that a 3-44% reduction in total annual refinery CO 2 emissions (2-24% reductions in the CO 2 emissions on a per barrel of crude oil processed) can be achieved in a medium conversion refinery that processes a typical U.S. crude slate obtained by using the technologies considered. A sensitivity analysis of the quality of input crude to a refinery, refinery configuration, and prices of natural gas and electricity revealed how the magnitude of possible CO 2 emissions reductions and the economic performance of the mitigation technologies can vary under different conditions. The analysis can help inform decision making related to investment decisions and CO 2 emissions policy in the refining sector.

  7. Environmental performance of an innovative waste refinery based on enzymatic treatment

    DEFF Research Database (Denmark)

    Tonini, Davide; Astrup, Thomas

    2011-01-01

    for virgin material and saving fossil resources. In this paper a life-cycle assessment of a pilot-scale waste refinery for the enzymatic treatment of municipal solid waste (MSW) is presented. The refinery produced a liquid (liquefied organic materials and paper) and a solid fraction (non-degradable materials......Decrease of fossil fuel dependence and global warming mitigation has become increasingly important issues during the last decades. With respect to waste management higher recycling rates for valuable materials as well as energy recovery from waste streams could play a significant role substituting......) from the waste. The waste refinery was compared to alternative treatments such as incineration, bioreactor landfill and mechanical-biological treatment followed by utilization of the RDF (refuse-derived fuel) for energy. The performance of the waste refinery turned out to be comparable...

  8. Profiles of foreign direct investment in US energy, 1992

    International Nuclear Information System (INIS)

    1994-01-01

    The report reviews the patterns of foreign ownership interest in US energy enterprises, exclusive of portfolio investment (<10% ownership of a US enterprise). It profiles the involvement of foreign-affiliated US companies in the following areas: domestic petroleum production (including natural gas), reserve holdings, refining and marketing activities, coal production, and uranium exploration and development

  9. Profiles of foreign direct investment in US energy, 1992

    Energy Technology Data Exchange (ETDEWEB)

    1994-05-16

    The report reviews the patterns of foreign ownership interest in US energy enterprises, exclusive of portfolio investment (<10% ownership of a US enterprise). It profiles the involvement of foreign-affiliated US companies in the following areas: domestic petroleum production (including natural gas), reserve holdings, refining and marketing activities, coal production, and uranium exploration and development.

  10. Net energy levels on the lipid profile of pork

    Directory of Open Access Journals (Sweden)

    Stephan Alexander da Silva Alencar

    2017-09-01

    Full Text Available ABSTRACT: This study was conducted to evaluate the effects of net energy levels on the lipid profile of adipose tissue and muscle of swines. A total of 90 animals, with initial weight of 71.94±4.43kg, were used, and distributed in a randomized block design in five net energy levels (2,300, 2,425, 2,550, 2,675, and 2,800Kcal kg-1 feed, with nine replicates and two animals per experimental unit. Lipid profiles of adipose tissue and muscle were analyzed using gas chromatography. Increasing the levels of net energy using soybean oil, improved the lipid profile of adipose tissue and muscle, increased linearly (P<0.05 the concentrations of polyunsaturated fatty acids, especially linoleic and α-linolenic acid, reduced linearly (P<0.05 the monounsaturated and saturated fatty acids and omega 6: omega 3. In adipose tissue was observed linear reduction (P<0.05 of atherogenic and thrombogenic indexes. In conclusion, increasing the level of net energy of the diet using soybean oil improved the lipid profile of adipose tissue and muscle.

  11. Basic investigation on promotion of joint implementation in fiscal 2000. Survey on energy saving and CO2 emission reduction in Cilacap Refinery; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Cilacap seiyusho ni okeru shoene CO2 sakugen chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With an objective of saving energy and reducing greenhouse gas emission, a basic survey has been performed on the atmospheric crude oil distillation units and the high vacuum distillation units at Cilacap Refinery in Indonesia. The first site survey in September 2000 has carried out a survey on the situation of the facilities and operation upon obtaining the facility data and operation information from Pertamina. As a result, it was revealed that there is a room of improvement in the heat recovery, whereas a modification design was executed on the improvement proposals on the heat exchanger system. However, the second site survey in November 2000 has revealed that Pertamina had executed in 1998 through 1999 the de-bottlenecking project on the crude oil atmospheric distillation units (two units) and the high vacuum distillation units (two units), by which the capability has been expanded, and the heat recovery rate has been increased. It is not possible to look for extremely large enhancement of the heat recovery rate beyond that point, and the reduction of CO2 emission would also be small. As a result of discussions, the present project was found capable of reducing annually the CO2 emission by 36,500 tons. (NEDO)

  12. Bioenergy, material, and nutrients recovery from household waste: Advanced material, substance, energy, and cost flow analysis of a waste refinery process

    DEFF Research Database (Denmark)

    Tonini, Davide; Dorini, Gianluca Fabio; Astrup, Thomas Fruergaard

    2014-01-01

    Energy, materials, and resource recovery from mixed household waste may contribute to reductions in fossil fuel and resource consumption. For this purpose, legislation has been enforced to promote energy recovery and recycling. Potential solutions for separating biogenic and recyclable materials...

  13. The prospects for refinery profitability

    Energy Technology Data Exchange (ETDEWEB)

    Weale, G. [European Energy Services, London (United Kingdom)

    1997-05-01

    The outlook for the European refining industry is assessed. The conclusion reached is that the industry is struggling for its existence. Over time, an unsatisfactory balance has grown between refinery capacity and market volumes. High exit barriers have prevented capacity being considerably lower than it is. In the future, a typical integrated oil company might be content to confine itself to retailing oil products without having to refine them. Given the reduction in gasoline demand in particular, it can be expected that 20-25% of capacity will be sold off in the next 15 years and much of it will be closed. (Author)

  14. Bioremediation of petroleum refinery effluent by Planococcus ...

    African Journals Online (AJOL)

    In the present investigation, Planococcus halophilus was screened for hydrocarbon degradation and bioremediation of refinery effluent. The test organism, P. halophilus, showed the capability to utilize kerosene as carbon source in minimal medium. Biological treatment of the refinery effluent with P. halophilus reduced the ...

  15. Aspects of petrochemistry in a fuels refinery

    Energy Technology Data Exchange (ETDEWEB)

    Esser, J.; Mielicke, C.J.; Maier, T. [MIRO - Mineraloelraffinerie Oberrhein GmbH und Co. KG, Karlsruhe (Germany)

    2007-07-01

    Classical links between refinery and petrochemical downstream operations are light naphtha, C2-C4-Olefins and various aromatic compounds. Additionally long chain paraffines from dewaxing or even heavy residues can be interesting starting materials for petrochemistry. Some aspects of these links between refining and petrochemistry as well as their impact on refinery operation and product pools are discussed. (orig.)

  16. US refineries lament lack of final CAA rules

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    Bush administration spokesman appeared unconvinced about the extent of the U.S. refining industry's problems at a Senate energy committee hearing. This paper reports that the oversight hearing examined various challenges facing refiners. Roger Beach, president of Unocal Refining and Marketing Division, testified for the National Petroleum Refiners Association, of which he is chairman. Beach the refineries still do not know what final Clean Air Act (CAA) amendments regulations will be, and state rules are changing, too

  17. Free energy profiles from single-molecule pulling experiments.

    Science.gov (United States)

    Hummer, Gerhard; Szabo, Attila

    2010-12-14

    Nonequilibrium pulling experiments provide detailed information about the thermodynamic and kinetic properties of molecules. We show that unperturbed free energy profiles as a function of molecular extension can be obtained rigorously from such experiments without using work-weighted position histograms. An inverse Weierstrass transform is used to relate the system free energy obtained from the Jarzynski equality directly to the underlying molecular free energy surface. An accurate approximation for the free energy surface is obtained by using the method of steepest descent to evaluate the inverse transform. The formalism is applied to simulated data obtained from a kinetic model of RNA folding, in which the dynamics consists of jumping between linker-dominated folded and unfolded free energy surfaces.

  18. Reducing refinery CO2 emissions through amine solvent upgrade and optimization

    Energy Technology Data Exchange (ETDEWEB)

    Alonso, Thiago V.; Valenzuela, Michelle [The Dow Chemical Company, Midland, MI (United States)

    2012-07-01

    Regional initiatives are underway to reduce and limit the emissions of greenhouse gases. With CO2 emissions making up over 80% of the greenhouse gases, cap-and-trade programs will focus on those industries that consume the most energy. Refineries are among the top energy consumers and are seeking opportunities to reduce usage. With tightening margins, energy management programs will not only help refineries meet CO{sub 2} emission regulations, but can also provide a competitive advantage. With the trend towards heavier and higher sulfur containing crudes, refineries are increasing processing capabilities, which can include capital-intensive projects and additional energy consumption. Energy conservation plans should include optimization of these processes. One area to consider includes the acid gas removal systems in refineries. Through the selection and use of optimal solvents and implementation of energy efficiency techniques, which require minimal capital investment and expenditures, refineries can reduce energy usage, overall CO{sub 2} emissions, and total cost in acid gas systems. This paper will discuss these approaches and share case studies detailing the implementation and results. (author)

  19. Petroleum Refinery Jobs and Economic Development Impact (JEDI) Model User Reference Guide

    Energy Technology Data Exchange (ETDEWEB)

    Goldberg, Marshall [MRG and Associates, Nevada City, CA (United States)

    2013-12-31

    The Jobs and Economic Development Impact (JEDI) models, developed through the National Renewable Energy Laboratory (NREL), are user-friendly tools utilized to estimate the economic impacts at the local level of constructing and operating fuel and power generation projects for a range of conventional and renewable energy technologies. The JEDI Petroleum Refinery Model User Reference Guide was developed to assist users in employing and understanding the model. This guide provides information on the model's underlying methodology, as well as the parameters and references used to develop the cost data utilized in the model. This guide also provides basic instruction on model add-in features, operation of the model, and a discussion of how the results should be interpreted. Based on project-specific inputs from the user, the model estimates job creation, earning and output (total economic activity) for a given petroleum refinery. This includes the direct, indirect and induced economic impacts to the local economy associated with the refinery's construction and operation phases. Project cost and job data used in the model are derived from the most current cost estimations available. Local direct and indirect economic impacts are estimated using economic multipliers derived from IMPLAN software. By determining the regional economic impacts and job creation for a proposed refinery, the JEDI Petroleum Refinery model can be used to field questions about the added value refineries may bring to the local community.

  20. Opportunities and challenges at the interface between petrochemistry and refinery. The BASF perspective

    Energy Technology Data Exchange (ETDEWEB)

    Blankertz, H.J. [BASF AG, Ludwigshafen (Germany)

    2007-07-01

    The author of the contribution under consideration reports on the BASF perspective according to opportunities and challenges at the interface between petrochemistry and refinery. This contribution is divided into the following chapters: (a) Overview BASF-Group; (b) Overview BASF Petrochemicals; (c) The refinery-chemistry interface; (d) Main focus refineries; (e) Interface challenges and opportunities; (f) What can BASF do for refineries. BASF employs the Verbund concept, a system that combines production with energy needs in an intelligent way. The idea is to reduce of primary energy carriers both in terms of raw materials and for power and steam generation. The authors describes the petrochemicals of BASF AG (Ludwigshafen, Federal Republic of Germany), the raw material development, evolution of thermal steamcracking and crackerproducts. Major feedstock source of the European petrochemical industry are streams out of refineries which can't be used for transportation fuels. The gap between propylene demand and production out of steam crackers has to be closed by propylene out for FCC's. Demand for aromatics (xylenes and benzene, and to a lesser extent toluene) needs to be filled in by aromatics out of refineries. Market drivers for the refining industry are lowering crude costs, growing clean products, increasing capacity and enhancing E and P integration. BASF has various business with the oil und refining industry and provides solutions for oil field chemicals, process chemicals and performance additives. The author explains which kind of products and services BASF provides for refiners.

  1. Bio-refinery approach for spent coffee grounds valorization.

    Science.gov (United States)

    Mata, Teresa M; Martins, António A; Caetano, Nídia S

    2018-01-01

    Although normally seen as a problem, current policies and strategic plans concur that if adequately managed, waste can be a source of the most interesting and valuable products, among which metals, oils and fats, lignin, cellulose and hemicelluloses, tannins, antioxidants, caffeine, polyphenols, pigments, flavonoids, through recycling, compound recovery or energy valorization, following the waste hierarchy. Besides contributing to more sustainable and circular economies, those products also have high commercial value when compared to the ones obtained by currently used waste treatment methods. In this paper, it is shown how the bio-refinery framework can be used to obtain high value products from organic waste. With spent coffee grounds as a case study, a sequential process is used to obtain first the most valuable, and then other products, allowing proper valorization of residues and increased sustainability of the whole process. Challenges facing full development and implementation of waste based bio-refineries are highlighted. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. South Africa's refineries: waiting for Maduna

    International Nuclear Information System (INIS)

    Anon.

    1997-01-01

    A definitive energy policy from the new Energy Minister, Penuell Maduna, is awaited by the petroleum industry in South Africa. Some of the complexities of the South African oil market and past legacies which make the task of producing a policy difficult, are examined here. They include the allegations made initially in 1994 that oil refineries are illegally repatriating profits by paying too much for imported products. Accusations of this transfer pricing have resurfaced in the light of recent figures published by the South African Petroleum Industry Association (SAPIA) which show that the oil industry's profitability is not as high as some had presumed. However, compelling evidence for the allegations has not appeared and it is unlikely that the foreign investors in SAPIA would endanger their operations in this way. SAPIA members are key investors in the national infrastructure and make large tax contributions much needed by the treasury. In its turn, SAPIA is unhappy about the continuation of the payment of large taxpayer funded subsidies to the privatised Sasol, the South African synthetic fuel company, seeing as anti-competitive and having negative implications for the national economy. For its part Sasol argues its entitlement to the same tariff protection enjoyed by 80% of local manufacturing industries in South Africa. Some government action has been taken to reduce the subsidies though. The oil companies in SAPIA require clarity on future energy policy and deregulation before committing themselves to further heavy capital investment and Sasol also requires an end to the present uncertainties. (UK)

  3. Fiscal 1999 research report. Basic research for promotion of joint implementation programs (Survey of energy saving and CO2 reduction at Omsk Refinery); 1999 nendo Omsk seiyusho ni okeru shoene CO{sub 2} sakugen chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The results of basic research conducted for scouting out projects which will attain the goals set forth in the COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change) protocol are compiled into a report. The atmospheric distillation unit for crude of the Omsk Refinery sited at Omsk City, Russian Federation, is the object of the research. A feasibility study is made about energy saving and reduction in CO2 emissions using various data acquired by an on-site survey, and seven modification plans are presented. In the preparation of the modification plans, 'the optimization of process systems,' 'the modification of the waste heat boiler,' and 'the installation of a new heating furnace' are taken into consideration. In relation to 'the optimization of process systems,' installation of a new heat exchanger and move to a different location of the existing heat exchanger are suggested in Modification Plan 1 and Modification Plan 2. Ultimately, seven modification plans are reviewed, which are combinations of Modification Plan 1, Modification Plan 2, 'the modification of the waste heat boiler,' and 'the installation of a new heating furnace.' Modification Plan 1 and Modification Plan 2 are attractive because they are high in performance for the small funds they require. Modification Plan 3 which includes 'the installation of a new heating furnace' demands a larger initial investment, but it achieves a greater reduction in CO2 emissions. (NEDO)

  4. Former Soviet refineries face modernization, restructuring

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    A massive modernization and restructuring program is under way in the refining sector of Russia and other former Soviet republics. Economic reforms and resulting economic dislocation following the collapse of the Soviet Union has left refineries in the region grappling with a steep decline and changes in product demand. At the same time, rising oil prices and an aging, dilapidated infrastructure promise a massive shakeout. Even as many refineries in the former Soviet Union (FSU) face possible closure because they are running at a fraction of capacity, a host of revamps, expansions, and grass roots refineries are planned or under way. The paper discusses plans

  5. Washington State Energy Use Profile, 1960--1990

    International Nuclear Information System (INIS)

    Anderson, M.

    1992-07-01

    This report is divided into three sections, each with data on energy consumption, prices, and expenditures. The first section presents an overview of statewide energy use trends. The second section presents energy use trends in four basic consuming sectors: residential, commercial, industrial, and transportation. The third section presents energy use trends in specific resource markets: natural gas, petroleum, electricity, coal, and wood. The appendixes contain information about data, sources, and a glossary. Data about Washington's energy resources are reported in two forms: in measures common to the fuel (kWh, barrels, etc.) and in the generic measure British thermal units (Btu). The common measures allow the reader to quickly grasp information in a familiar form. The generic measure allows the reader to compare energy resources. Conversion to Btu occasionally produces counter-intuitive results. For example, in different years, petroleum products have different average energy values, resulting in different conversion factors from barrels to Btu. A large amount of data contained in the Profile has been categorized and presented in a variety of ways. Understanding the meaning of categories is critical to understanding differences between the tables, especially those tables that present similar data. For example, petroleum trends are not the same as transportation trends, though they are similar because transportation is almost entirely dependent on petroleum. In another example, total end-use fuel energy consumption is not the same as total primary energy consumption. End-use fuel consumption does not include energy used for the generation of electricity. Counting both fuel used for electricity generation and electricity itself could result in double counting. Primary fuel consumption, on the other hand, does include energy used for the generation of electricity and is greater than total end-use consumption

  6. Analysis of standard and innovative methods for allocating upstream and refinery GHG emissions to oil products

    International Nuclear Information System (INIS)

    Moretti, Christian; Moro, Alberto; Edwards, Robert; Rocco, Matteo Vincenzo; Colombo, Emanuela

    2017-01-01

    Highlights: •Traditional and innovative methods for allocating emissions at refinery level are reviewed. •Added value has been introduced as a novel allocation method. •Hydrogen-based consistency test has been introduced to validate the allocation methods. •Consistent allocation methods assign negative refinery emissions to heavy products. -- Abstract: Alternative fuel policies need accurate and transparent methods to find the embedded carbon intensity of individual refinery products. This study investigates different ways of allocating greenhouse gases emissions deriving from refining and upstream crude oil supply. Allocation methods based on mass, energy content, economic value and, innovatively, added-value, are compared with the marginal refining emissions calculated by CONCAWE’s linear-programming model to the average EU refinery, which has been adopted as reference in EU legislation. Beside the most important transportation fuels (gasoline, diesel, kerosene/jet fuel and heavy fuel oil), the analysis extends to petroleum coke and refinery hydrogen. Moreover, novel criteria, based on the implications due to hydrogen usage by each fuel pathway, have been introduced to test the consistency of the analyzed approaches. It is found that only two economic-based allocation methods are consistent with the introduced criteria. These two methods also give negative refinery emissions for heavy products, which is coherent with the marginal emissions calculated through the CONCAWE refinery model. The recommended allocation methods are transparent and use only publicly available statistical data, so they may be useful not only for future EU legislation, but also in jurisdictions where a representative refinery model is not available.

  7. Mild Biomass Liquefaction Process for Economic Production of Stabilized Refinery-Ready Bio-oil

    Energy Technology Data Exchange (ETDEWEB)

    Gangwal, Santosh [Southern Research, Durham, NC (United States); Meng, Jiajia [Southern Research, Durham, NC (United States); McCabe, Kevin [Southern Research, Durham, NC (United States); Larson, Eric [Princeton Univ., NJ (United States). Princeton Environmental Inst.; Mastro, Kelly [Southern Research, Durham, NC (United States)

    2016-04-25

    Southern Research (SR) in cooperation with U.S. Department of Energy (DOE), Bioenergy Technology Office (BETO), investigated a biomass liquefaction process for economic production of stabilized refinery-ready bio-oil. The project was awarded by DOE under a Funding Opportunity Announcement (DE-FOA-0000686) for Bio-oil Stabilization and Commoditization that intended to evaluate the feasibility of using bio-oil as a potential feedstock in an existing petroleum refinery. SR investigated Topic Area 1 of the FOA at Technology Readiness Level 2-3 to develop thermochemical liquefaction technologies for producing a bio-oil feedstock from high-impact biomass that can be utilized within a petroleum refinery. Bio-oil obtained from fast pyrolysis of biomass is a green intermediate that can be further upgraded into a biofuel for blending in a petroleum refinery using a hydro-deoxygenation (HDO) route. Co-processing pyrolysis bio-oil in a petroleum refinery is an attractive approach to leverage the refinery’s existing capital. However, the petroleum industry is reluctant to accept pyrolysis bio-oil because of a lack of a standard definition for an acceptable bio-oil feedstock in existing refinery processes. Also per BETO’s multiyear program plan, fast pyrolysis-based bio-fuel is presently not cost competitive with petroleum-based transportation fuels. SR aims to develop and demonstrate a cost-effective low-severity thermal liquefaction and hydrodeoxygenation (HDO) process to convert woody biomass to stabilized bio-oils that can be directly blended with hydrotreater input streams in a petroleum refinery for production of gasoline and/or diesel range hydrocarbons. The specific project objectives are to demonstrate the processes at laboratory scale, characterize the bio-oil product and develop a plan in partnership with a refinery company to move the technology towards commercialization.

  8. Catalysis as a tool for energy conservation in the refinery industry; Catalisis como herramienta de ahorro de energia en la industria de la refinacion

    Energy Technology Data Exchange (ETDEWEB)

    Castillo, S.; Moran-Pineda, M. [Instituto Mexicano del Petroleo, Mexico, D. F. (Mexico); Bazan, G.; Gonzalez, L.; Barrios, H. [Pemex-Refinacion, Mexico, D. F. (Mexico)

    1996-12-31

    The catalysis, defined by the alchemists since its appearance, as that something or Philosophical Stone, with a special power to transform matter by means of the energy, has always represented a challenge to mankind, even more now, when most of the goods needed for its survival are related to a chemical process and nowadays, when they can not be imagined without the presence of a catalyzer. In the reciprocity between the chemical change and the catalyzer, the energy utilized represents the critical point. Once stated the above, it becomes interesting the study of the impact and the consequence of the binomial catalysis-energy in relation to the fuel recovery processes and the emission control processes, originated by its combustion, where the main objective is in establishing an analysis criterion for energy conservation with different trends; the first one, on the impact of the application of optimum catalytic systems in the fuel recovery processes and the second one on the optimum catalytic processes for emissions control. [Espanol] La catalisis desde su aparicion definida por los alquimistas como ese algo o piedra filosofal, con una fuerza especial para la transformacion de la materia mediante la energia, siempre ha representado un reto para el hombre, mas aun en la actualidad donde la mayoria de los bienes necesarios para su supervivencia estan relacionados con un proceso quimico y que hoy en dia no se conciben estos sin la presencia de un catalizador. En la reciprocidad entre el cambio quimico y el catalizador, la energia utilizada representa el punto critico. Dado lo anterior, resulta interesante el estudio del impacto y trascendencia del binomio catalisis-energia en relacion con los procesos para la obtencion de los combustibles y de los procesos para el control de emisiones, producto de la combustion de los mismos, donde el objetivo primordial esta en establecer un criterio de analisis de ahorro de energia con diferentes directrices; la primera, el impacto

  9. Catalysis as a tool for energy conservation in the refinery industry; Catalisis como herramienta de ahorro de energia en la industria de la refinacion

    Energy Technology Data Exchange (ETDEWEB)

    Castillo, S; Moran-Pineda, M [Instituto Mexicano del Petroleo, Mexico, D. F. (Mexico); Bazan, G; Gonzalez, L; Barrios, H [Pemex-Refinacion, Mexico, D. F. (Mexico)

    1997-12-31

    The catalysis, defined by the alchemists since its appearance, as that something or Philosophical Stone, with a special power to transform matter by means of the energy, has always represented a challenge to mankind, even more now, when most of the goods needed for its survival are related to a chemical process and nowadays, when they can not be imagined without the presence of a catalyzer. In the reciprocity between the chemical change and the catalyzer, the energy utilized represents the critical point. Once stated the above, it becomes interesting the study of the impact and the consequence of the binomial catalysis-energy in relation to the fuel recovery processes and the emission control processes, originated by its combustion, where the main objective is in establishing an analysis criterion for energy conservation with different trends; the first one, on the impact of the application of optimum catalytic systems in the fuel recovery processes and the second one on the optimum catalytic processes for emissions control. [Espanol] La catalisis desde su aparicion definida por los alquimistas como ese algo o piedra filosofal, con una fuerza especial para la transformacion de la materia mediante la energia, siempre ha representado un reto para el hombre, mas aun en la actualidad donde la mayoria de los bienes necesarios para su supervivencia estan relacionados con un proceso quimico y que hoy en dia no se conciben estos sin la presencia de un catalizador. En la reciprocidad entre el cambio quimico y el catalizador, la energia utilizada representa el punto critico. Dado lo anterior, resulta interesante el estudio del impacto y trascendencia del binomio catalisis-energia en relacion con los procesos para la obtencion de los combustibles y de los procesos para el control de emisiones, producto de la combustion de los mismos, donde el objetivo primordial esta en establecer un criterio de analisis de ahorro de energia con diferentes directrices; la primera, el impacto

  10. Mazeikiai refinery woes deepen on all fronts

    Index Scriptorium Estoniae

    2007-01-01

    Leedu rahandusminister teatas, et riigieelarvet mõjutavad probleemid Mazeikiai tehasega, mis on Leedu suurim maksumaksja. Lisa: Russian oil company to build refinery. Surgutneftegaz teatas plaanist ehitada naftatöötlustehas Peterburi lähedale

  11. Refinery siting workbook: appendices A and B

    Energy Technology Data Exchange (ETDEWEB)

    1980-07-01

    The objective of this effort is to develop and provide basic refinery-related information for use by state and local government officials as a basis for establishing responsible refinery siting requirements and policies consistent with the federal clean air and water standards and socio-economic concerns. The report will be organized into two volumes. The main text comprises the basic topics of physical concerns, regulatory requirements, and permitting activities, while the second volume includes the detailed appendix materials such as the applicable laws, and the necessary permits, as available and a glossary of pertinent terms. As a means to this objective, three refinery sizes, 200,000, 100,000 and 30,000 barrels per day crude charge will be discussed in technical terms. Process unit configuration will be presented which will maximize either gasoline or heating oil production with either sweet or sour crude oil feedstocks. The major issues affecting the socio-economic impact of siting the refinery in a given locale will be presented. These data will review the factors affecting the human environment and the issues that must be addressed to assess the impact that a refinery will have on a community. The key federal registrations which impact upon a refinery siting decision shall be reviewed. Summaries of these regulations and a simplified decision diagram for the air and water acts shall be presented to assist both government and refinery officials in understanding the scope of regulatory impact. All pertinent procedures required for refinery permitting shall be reviewed under the generalized headings of air, water, health and safety, land use, and miscellaneous permits. This categorization at the federal, state and local levels of government shall be used as a basis for establishing degrees of emphasis.

  12. Improving profitability in a grassroots refinery

    Energy Technology Data Exchange (ETDEWEB)

    Coombs, T. [Star Petroleum Refining Co. Ltd. (Thailand); Kennedy, P.; Bhargava, S. [KBC Process Technology Ltd. (United Kingdom)

    1999-05-01

    Actions taken to maximise profit at the Star Refinery in Thailand are described. The company made good use of the Profit Improvement Programme (PIP) (which specialises in refinery economics) and the way in which PIP addressed the problem and the benefits derived therefrom is the nub of this paper. The efforts appear to have been more than satisfactory from the aspect of increasing profit margins. (UK)

  13. Complexity index indicates refinery capability, value

    International Nuclear Information System (INIS)

    Johnston, D.

    1996-01-01

    Refinery size usually is measured in terms of distillation capacity. Relative size, however, can be measured using refinery complexity--a concept developed by W.L. Nelson in the 1960s. Nelson developed the complexity index to quantify the relative cost of components that make up a refinery. It is a pure cost index that provides a relative measure of the construction costs of a particular refinery based on its crude and upgrading capacity. The Nelson index compares the costs of various upgrading units--such as a fluid catalytic cracking (FCC) unit or a catalytic reformer--to the cost of a crude distillation unit. Computation of the index is an attempt to quantify the relative cost of a refinery based on the added cost of various upgrading units and the relative upgrading capacity. A review of complexity calculations, and an explanation of how indices have changed, provide a simple means of determining the complexity of single refineries or refining regions. The impact of complexity on product slate is also examined in this paper

  14. The rise and fall of refineries

    International Nuclear Information System (INIS)

    Chretien, D.

    2002-01-01

    This paper described the rise and fall of refineries in Montreal. Well before Calgary, Montreal was the hub of activity for oil refineries because Montreal was the principle consuming market for petroleum products in Canada. The location was good, particularly since the soil was clay which helped prevent soil infiltration of petroleum. The first refinery in Montreal was constructed in 1916 by Esso, followed by Texaco in 1921 and Gulf in 1931. Initially oil was shipped by boat to the Port of Montreal from Saudi Arabia. Later, the petroleum came mostly from Venezuela. At the beginning of the 1980s many refineries were closed because they became obsolete and upgrading them would have been too costly. Only 3 refineries remain in Quebec, of which 2 are in Montreal. They are owned by Shell and PetroCanada. The third refinery in Quebec is in St-Romuald and is owned by UltraMar. One of the major contributing factors to the decline of the refining industry in Montreal was the decision in 1984 by former Prime Minister Trudeau to force Canadian provinces to purchase their petroleum from Alberta. This caused the petrochemical industry to locate in Sarnia in Ontario, leaving the Montreal refining centre to become obsolete. 3 figs

  15. The vacuum profile of the energy spectrum compressor

    International Nuclear Information System (INIS)

    Kuijsten, W.J.

    1988-12-01

    A finite element model has been made of the vacuum system of the Energy Spectrum Compressor. It gives the possibility to calculate the average pressure profile of the system in a fast way. It is required that the average pressure in the system does not influence the present performance of the linac nor the performance of the beam switch yard. Calculations show that with standard pumps of 60 l/s an average pressure of -5 Pa can be obtained. 7 refs.; 8 figs.; 2 tabs

  16. Impact of the evolution of petroleum products demand on the energy consumption and CO{sub 2} emissions of refineries; Impact de l'evolution de la demande de produits petroliers sur la consommation d'energie et les emissions de CO{sub 2} des raffineries

    Energy Technology Data Exchange (ETDEWEB)

    Tehrani Nejad Moghaddam, A

    2008-01-15

    The French refining industry is in a paradoxical situation. Although the energy efficiency of the refineries have been significantly improved their CO{sub 2} emissions are continuously increasing and this trend will be kept in future. The origin of this paradox steams in the profound modification in the demand structure (in terms of quantity and quality) of the oil products. The objective of this dissertation is to provide answers to these paradoxical questions. This objective is achieved and can be summarized in three points: (1) the introduction of linear programming to the prospective and retrospective life cycle assessment analysis (2) the evaluation of the impact of tightening the sulfur specification on the marginal cost and marginal CO{sub 2} contribution of oil products (3) the assessment of the average CO{sub 2} coefficients for oil products useful in the life cycle assessment studies. (author)

  17. Catalytic hydrotreatment of refinery waste

    Energy Technology Data Exchange (ETDEWEB)

    1989-01-01

    The object of the project is to produce liquid hydrocarbons by the catalytic hydroprocessing of solid refinery wastes (hard pitches) in order to improve the profitability of deep conversion processes and reduce the excess production of heavy fuels. The project was mostly carried out on the ASVAHL demonstration platform site, at Solaize, and hard pitches were produced primarily by deasphalting of atmospheric or vacuum distillation residues. The project includes two experimental phases and an economic evaluation study phase. In phase 1, two granular catalysts were used to transform pitch into standard low sulphur fuel oil: a continuously moving bed, with demetallation and conversion catalyst; a fixed bed, with hydrorefining catalyst. In phase 2 of the project, it was proven that a hydrotreatment process using a finely dispersed catalyst in the feedstock, can, under realistic operating conditions, transform with goods yields hard pitch into distillates that can be refined through standard methods. In phase 3 of the project, it was shown that the economics of such processes are tightly linked to the price differential between white and black oil products, which is expected to increase in the future. Furthermore, the evolution of environmental constraints will impel the use of such methods, thus avoiding the coproduction of polluting solid residues.

  18. Bioremediation at a petroleum refinery

    International Nuclear Information System (INIS)

    Carson, A.W.; Jarvis, J.; Richardson, K.E.

    1994-01-01

    This paper presents a summary of three projects at the Mobil Refinery in Torrance, California where bioremediation technologies were successfully employed for the remediation of hydrocarbon contaminated soil. The three projects represent variations of implementation of bioremediation, both in-situ and ex-situ. Soil from all of the projects was considered non-hazardous designated waste under the California Code of Regulations, Title 23, section 2522. The projects were permitted and cleanup requirements were defined with the Los Angeles Regional Water Quality Control Board. In all of the projects, different methods were used for supplying water, oxygen, and nutrients to the hydrocarbon degrading bacteria to stimulate growth. The Stormwater Retention Basin Project utilized in-situ mechanical mixing of soils to supply solid nutrients and oxygen, and a self-propelled irrigation system to supply water. The Tank Farm Lake project used an in-situ active bioventing technology to introduce oxygen, moisture, and vapor phase nutrients. The Tank 1340X247 project was an ex-situ bioventing remediation project using a drip irrigation system to supply water and dissolved nutrients, and a vapor extraction system to provide oxygen

  19. Refinery boom in Southeast Asia

    International Nuclear Information System (INIS)

    Gruson, J.F.; Virondaud, C.

    1996-01-01

    The Asia demand for oil is increasing dramatically, particularly in the non OECD countries, which represent, today more than 15 % of the world oil market. The expected economic growth in these areas should contribute to a rise in oil demand by about 5.4 per year and hence to a significant increase of this share to 25 % in 2010; virtually a large part of this evolution will come from the transportation sector. The proceeding investments of the regional, refining industry are very high (some evaluations come to around 140 billion of dollars), all the more the protection of the environment takes an increasing significant place. Accordingly the most important challenge to be taken up by these countries will be to mobilize long term fundings to develop and adapt the capabilities of the refineries to meet the growth of gasoline and gas oil demand. The contribution of private operators or capital will be necessary, but will depend strongly on refining margin improvement and on progress of free market areas announced by several countries. (authors)

  20. An energy-efficient metro speed profiles for energy savings: application to the Valencia metro

    Energy Technology Data Exchange (ETDEWEB)

    Villalba Sanchis, I.; Salvador Zuriaga, P.

    2016-07-01

    Nowadays one of the main priorities for metro line operators is the reduction of energy consumption, due to the environmental impact and economic cost. In order to achieve this objective different strategies can be applied, normally focused into rolling stock, infrastructure and/or operation. Considering short-term measures and related to the traffic operation strategies, different approaches are being researched. One of the most effective strategy which reduce net energy consumption is the use of efficient driving techniques. These techniques produces a speed profile between two stations that requires the minimum net energy consumption, without degrading commercial running times or passenger comfort. In this paper, a computer model for calculating the metro vehicles speed profiles minimizing the energy consumption was developed. The equations considered in the model represent the behavior of a single vehicle operated under manual driving, subject to different constraints such as the headway, cycle time, distances and acceleration limits. The proposed model calculates different commands to be systematically executed by the driver. The resulting simulator has been tuned by means of on board measurements of speed, accelerations and energy consumption obtained along different lines in Metro de Valencia network. For this purpose, different scenarios are analyzed to assess the achievable energy savings. In general terms and comparing with the actual energy consumption, the solutions proposed can reduce the net energy consumption around 19%. (Author)

  1. Eldorado Port Hope refinery - uranium production (1933-1951)

    International Nuclear Information System (INIS)

    Arsenault, J.E.

    2008-01-01

    Since the discovery of pitchblende in 1930 by Gilbert LaBine at Great Bear Lake (GBL), North West Territories, uranium has played a central role in the growth of the Canadian mining sector and it in turn has propelled the country into it's present position as the world's top uranium producer. The rich ore mined there was used originally by Eldorado Gold Mines Limited to build a business based on the extraction of radium, which was selling at $70,000 a gram at the time, and silver which was present in the ore in commercial amounts. The mine site on GBL became known as Port Radium. In 1933 Eldorado brought a refinery on-line at Port Hope, Ontario nearly 4,000 miles away from the mine, and began to produce radium, silver and uranium products. Initially uranium played a minor role in the business and the products were sold into the ceramics industry to manufacture a variety of crockery with long-lasting colours. In addition, there were sales and loans of uranium products to research laboratories that were exploring nuclear energy for possible use in weapons and power generation, as the potential for this was clearly understood from 1939 onwards. These laboratories included the National Research Council (George Laurence), Columbia University (Enrico Fermi) and International Chemical Industries (J.P. Baxter). With the beginning of World War II the radium business suffered from poor sales and by 1940 the mine was closed but the refinery continued operation, using accumulated stockpiles. By 1942 uranium had become a strategic material, the mine was reopened, and the refinery began to produce large quantities of uranium oxide destined for The Manhattan Project. As events unfolded Eldorado was unable to produce sufficient ore from GBL so that a large quantity of ore from the Belgian Congo was also processed at Port Hope. Ultimately, as a result of the efforts of this enterprise, World War II was finally ended by use of atomic weapons. After World War II the refinery

  2. Eldorado Port Hope refinery - uranium production (1933-1951)

    Energy Technology Data Exchange (ETDEWEB)

    Arsenault, J.E

    2008-03-15

    Since the discovery of pitchblende in 1930 by Gilbert LaBine at Great Bear Lake (GBL), North West Territories, uranium has played a central role in the growth of the Canadian mining sector and it in turn has propelled the country into it's present position as the world's top uranium producer. The rich ore mined there was used originally by Eldorado Gold Mines Limited to build a business based on the extraction of radium, which was selling at $70,000 a gram at the time, and silver which was present in the ore in commercial amounts. The mine site on GBL became known as Port Radium. In 1933 Eldorado brought a refinery on-line at Port Hope, Ontario nearly 4,000 miles away from the mine, and began to produce radium, silver and uranium products. Initially uranium played a minor role in the business and the products were sold into the ceramics industry to manufacture a variety of crockery with long-lasting colours. In addition, there were sales and loans of uranium products to research laboratories that were exploring nuclear energy for possible use in weapons and power generation, as the potential for this was clearly understood from 1939 onwards. These laboratories included the National Research Council (George Laurence), Columbia University (Enrico Fermi) and International Chemical Industries (J.P. Baxter). With the beginning of World War II the radium business suffered from poor sales and by 1940 the mine was closed but the refinery continued operation, using accumulated stockpiles. By 1942 uranium had become a strategic material, the mine was reopened, and the refinery began to produce large quantities of uranium oxide destined for The Manhattan Project. As events unfolded Eldorado was unable to produce sufficient ore from GBL so that a large quantity of ore from the Belgian Congo was also processed at Port Hope. Ultimately, as a result of the efforts of this enterprise, World War II was finally ended by use of atomic weapons. After World War II the

  3. Fiscal 1999 report on basic research for promotion of joint implementation programs. Energy saving project for West Pacific Petrochemical Co., Ltd., Dalian/West Pacific Oil Refinery; 1999 nendo Dalian Nishitaiheiyo sekiyu kako yugen koji Nishitaiheiyo seiyusho shoene project chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    An energy saving survey is conducted for the above named plant under a project expected to be linked to the clean development mechanism of COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change). Supply/demand balance is poor at various utilities in this refinery, with surplus steam in summer and with hydrogen rich surplus off gas (flare combustion, discharge into the air) from the respective devices causing numerous problems about energy efficiency. Under the project, hydrogen will be recovered from the refinery off gas for utilization, systems related to fuel, steam, and power will be improved, and a surplus gas fired turbine power generating facility will be installed. Power generation of 29MW is feasible, which elevates the percentage of private power generation to the total demand for power from 25% to 71%. The purchase of power from external coal fired power stations will decrease greatly, contributing to energy saving. A yearly amount of 136-thousand tons of CO2 will be reduced thanks to the hydrogen recovery system and the gas turbine power generating facility to be newly installed. The Chinese party, much interested in the project, intends to be a participant as a joint implementer. The Japanese party has received a request for technological and financial assistance. (NEDO)

  4. Energy Models

    Science.gov (United States)

    Energy models characterize the energy system, its evolution, and its interactions with the broader economy. The energy system consists of primary resources, including both fossil fuels and renewables; power plants, refineries, and other technologies to process and convert these r...

  5. Energy profile of nanobody–GFP complex under force

    International Nuclear Information System (INIS)

    Klamecka, Kamila; Severin, Philip M; Milles, Lukas F; Gaub, Hermann E; Leonhardt, Heinrich

    2015-01-01

    Nanobodies (Nbs)—the smallest known fully functional and naturally occuring antigen-binding fragments—have attracted a lot of attention throughout the last two decades. Exploring their potential beyond the current use requires more detailed characterization of their binding forces as those cannot be directly derived from the binding affinities. Here we used atomic force microscope to measure rupture force of the Nb–green fluorescent protein (GFP) complex in various pulling geometries and derived the energy profile characterizing the interaction along the direction of the pulling force. We found that—despite identical epitopes—the Nb binds stronger (41–56 pN) to enhanced GFP than to wild-type GFP (28–45 pN). Measured forces make the Nb–GFP pair a potent reference for investigating molecular forces in living systems both in and ex vivo. (paper)

  6. Energy profile of nanobody-GFP complex under force

    Science.gov (United States)

    Klamecka, Kamila; Severin, Philip M.; Milles, Lukas F.; Gaub, Hermann E.; Leonhardt, Heinrich

    2015-10-01

    Nanobodies (Nbs)—the smallest known fully functional and naturally occuring antigen-binding fragments—have attracted a lot of attention throughout the last two decades. Exploring their potential beyond the current use requires more detailed characterization of their binding forces as those cannot be directly derived from the binding affinities. Here we used atomic force microscope to measure rupture force of the Nb-green fluorescent protein (GFP) complex in various pulling geometries and derived the energy profile characterizing the interaction along the direction of the pulling force. We found that—despite identical epitopes—the Nb binds stronger (41-56 pN) to enhanced GFP than to wild-type GFP (28-45 pN). Measured forces make the Nb-GFP pair a potent reference for investigating molecular forces in living systems both in and ex vivo.

  7. Energy profile of nanobody-GFP complex under force.

    Science.gov (United States)

    Klamecka, Kamila; Severin, Philip M; Milles, Lukas F; Gaub, Hermann E; Leonhardt, Heinrich

    2015-09-10

    Nanobodies (Nbs)-the smallest known fully functional and naturally occuring antigen-binding fragments-have attracted a lot of attention throughout the last two decades. Exploring their potential beyond the current use requires more detailed characterization of their binding forces as those cannot be directly derived from the binding affinities. Here we used atomic force microscope to measure rupture force of the Nb-green fluorescent protein (GFP) complex in various pulling geometries and derived the energy profile characterizing the interaction along the direction of the pulling force. We found that-despite identical epitopes-the Nb binds stronger (41-56 pN) to enhanced GFP than to wild-type GFP (28-45 pN). Measured forces make the Nb-GFP pair a potent reference for investigating molecular forces in living systems both in and ex vivo.

  8. Benzene exposure in a Japanese petroleum refinery.

    Science.gov (United States)

    Kawai, T; Yamaoka, K; Uchida, Y; Ikeda, M

    1990-07-01

    Time-weighted average (TWA) intensity of exposure of workers to benzene vapor during a shift was monitored by diffusive sampling technique in a Japanese petroleum refinery. The subjects monitored (83 in total) included refinery operators, laboratory personnel and tanker-loading workers. The results showed that the time-weighted average exposures are well below 1 ppm in most cases. The highest exposure was recorded in 1 case involved in bulk loading of tanker ships, in which exposure of over 1 ppm might take place depending on operational conditions. The observation was generally in agreement with levels previously reported.

  9. [Occupational accidents in an oil refinery in Brazil].

    Science.gov (United States)

    Souza, Carlos Augusto Vaz de; Freitas, Carlos Machado de

    2002-10-01

    Work in oil refineries involves the risk of minor to major accidents. National data show the impact of accidents on this industry. A study was carried out to describe accident profile and evaluate the adequacy of accident reporting system. Data on all accidents reported in an oil refinery in the state of Rio de Janeiro for the year 1997 were organized and analyzed. The study population consisted of 153 injury cases, 83 hired and 69 contracted workers. The variables were: type of accident, operation mode and position of the worker injured. Among hired workers, minor accidents predominated (54.2%) and they occurred during regular operation activities (62.9%). Among contracted workers, there also predominated minor accidents (75.5%) in a higher percentage, but they occurred mainly during maintenance activities (96.8%). The study results showed that there is a predominance of accidents in lower hierarchy workers, and these accidents occur mainly during maintenance activities. There is a need to improve the company's accident reporting system and accident investigation procedures.

  10. Environmental and economic sustainability of integrated production in bio-refineries : The thistle case in Sardinia

    NARCIS (Netherlands)

    Yazan, Devrim; Mandras, Giovanni; Garau, Giorgio

    2016-01-01

    This paper aims at evaluating the environmental and economic sustainability of bio-refineries that produce multiple products through their supply chains (SCs). A physical enterprise input-output (EIO) model is used to quantify the material/energy/waste flows and integrated to the monetary EIO model

  11. Integrated pollution control for oil refinery complexes

    Energy Technology Data Exchange (ETDEWEB)

    Kiperstok, A. [Bahia Univ., Salvador, BA (Brazil); Sharratt, P.N. [Manchester Univ. (United Kingdom). Inst. of Science and Technology

    1993-12-31

    Improving environmental performance of oil refineries is a complex task. Emission limits, operating constraints, available technologies, operating techniques, and local environment sensitivity must all be considered. This work describes efforts to build an interactive software to deal with this problem. 8 refs., 5 figs.

  12. Integrated pollution control for oil refinery complexes

    Energy Technology Data Exchange (ETDEWEB)

    Kiperstok, A [Bahia Univ., Salvador, BA (Brazil); Sharratt, P N [Manchester Univ. (United Kingdom). Inst. of Science and Technology

    1994-12-31

    Improving environmental performance of oil refineries is a complex task. Emission limits, operating constraints, available technologies, operating techniques, and local environment sensitivity must all be considered. This work describes efforts to build an interactive software to deal with this problem. 8 refs., 5 figs.

  13. Refinery siting workbook: appendices C to O

    Energy Technology Data Exchange (ETDEWEB)

    1980-07-01

    Applicable laws and permits available for the selection and building of petroleum refineries are enclosed. A glossary of pertinent terms is also included. References related to the National Environmental Policy Act, the Clean Air Act, the Federal Water Pollution Control Act, Resource Conservation and Recovery Act, Toxic Substance Control Act, and Wetlands and Coastal Zone are included. Permit information is also presented. (DC)

  14. The life and times of a western refinery

    International Nuclear Information System (INIS)

    Thomas, W.

    1998-01-01

    An historical account is given of the discovery of oil by Imperial Oil Ltd., at Leduc in 1947, and the opening of a refinery in Edmonton in 1948. The discovery at Leduc was the first major strike to be made in western Canada, but Imperial Oil did not have a refinery at the site to process the new found crude. Given the economic constraints of the postwar era, Imperial Oil decided to dismantle and move an idle and virtually brand-new refinery located at Whitehorse, Yukon. It took 10 months to reassemble the refinery at its newly prepared site at Edmonton. Regular expansions and improvements helped to ensure that the refinery kept up with the advances in technology and market demand. By the early 1970s, small refineries were becoming uneconomical as distribution of products by pipelines became possible. In 1976 Imperial Oil spent more than $300 million to consolidate its four Prairie refineries, those in Calgary, Winnipeg, Regina and Edmonton, into one large facility at the Edmonton site. The role that the refinery plays in today's community and the effort that Imperial Oil makes to comply with stringent environmental regulations were described. Today, the refinery is producing 165,000 barrels a day of fuels and lubricants and another 20,000 barrels of asphalt. The refinery supplies more than 200 different products to customers across Canada, with unit costs which are amongst the lowest of North American refineries. figs

  15. Production planning and scheduling in refinery industry

    International Nuclear Information System (INIS)

    Persson, Jan.

    1999-01-01

    In this thesis we consider production planning and scheduling in refinery industry, in particular we study the planning and scheduling at the Nynaes AB refinery and at the Scanraff AB refinery. The purpose is to contribute to the development and the use of optimization models to support efficient decision making. We identify various decision problems concerning the aggregated production planning, the shipment planning, the scheduling of operation modes, and the utilization of pipes and tanks; and we discuss the potential to successfully apply optimization models on these problems. We formulate a mixed integer linear programming model for the scheduling of operation modes at Nynaes. The model concerns decisions about which mode of operation to use at a particular point in time in order to minimize costs of changing modes and costs of keeping inventories, given demands for products. We derive several types of valid inequalities for this mathematical problem and show how these inequalities can improve the lower bound obtained from the linear programming relaxation of the problem. We also show how the valid inequalities can be used to improve the performance of a branch and bound solution approach. Further, a tabu search heuristic is developed for the scheduling problem. The solution methods are tested on data provided by the Nynaes refinery, and the performance of the methods are discussed. We present several extensions of the proposed model, and illustrate how the model can be used to support both operational and strategic decision making at the refinery. 66 refs, 6 figs, 32 tabs. Also published as: Dissertation from the International Graduate School of Management and Industrial Engineering, No 25, Licenciate Thesis

  16. Production planning and scheduling in refinery industry

    Energy Technology Data Exchange (ETDEWEB)

    Persson, Jan

    1999-07-01

    In this thesis we consider production planning and scheduling in refinery industry, in particular we study the planning and scheduling at the Nynaes AB refinery and at the Scanraff AB refinery. The purpose is to contribute to the development and the use of optimization models to support efficient decision making. We identify various decision problems concerning the aggregated production planning, the shipment planning, the scheduling of operation modes, and the utilization of pipes and tanks; and we discuss the potential to successfully apply optimization models on these problems. We formulate a mixed integer linear programming model for the scheduling of operation modes at Nynaes. The model concerns decisions about which mode of operation to use at a particular point in time in order to minimize costs of changing modes and costs of keeping inventories, given demands for products. We derive several types of valid inequalities for this mathematical problem and show how these inequalities can improve the lower bound obtained from the linear programming relaxation of the problem. We also show how the valid inequalities can be used to improve the performance of a branch and bound solution approach. Further, a tabu search heuristic is developed for the scheduling problem. The solution methods are tested on data provided by the Nynaes refinery, and the performance of the methods are discussed. We present several extensions of the proposed model, and illustrate how the model can be used to support both operational and strategic decision making at the refinery. 66 refs, 6 figs, 32 tabs. Also published as: Dissertation from the International Graduate School of Management and Industrial Engineering, No 25, Licenciate Thesis.

  17. Production planning and scheduling in refinery industry

    Energy Technology Data Exchange (ETDEWEB)

    Persson, Jan

    1999-06-01

    In this thesis we consider production planning and scheduling in refinery industry, in particular we study the planning and scheduling at the Nynaes AB refinery and at the Scanraff AB refinery. The purpose is to contribute to the development and the use of optimization models to support efficient decision making. We identify various decision problems concerning the aggregated production planning, the shipment planning, the scheduling of operation modes, and the utilization of pipes and tanks; and we discuss the potential to successfully apply optimization models on these problems. We formulate a mixed integer linear programming model for the scheduling of operation modes at Nynaes. The model concerns decisions about which mode of operation to use at a particular point in time in order to minimize costs of changing modes and costs of keeping inventories, given demands for products. We derive several types of valid inequalities for this mathematical problem and show how these inequalities can improve the lower bound obtained from the linear programming relaxation of the problem. We also show how the valid inequalities can be used to improve the performance of a branch and bound solution approach. Further, a tabu search heuristic is developed for the scheduling problem. The solution methods are tested on data provided by the Nynaes refinery, and the performance of the methods are discussed. We present several extensions of the proposed model, and illustrate how the model can be used to support both operational and strategic decision making at the refinery. 66 refs, 6 figs, 32 tabs. Also published as: Dissertation from the International Graduate School of Management and Industrial Engineering, No 25, Licenciate Thesis

  18. Cleaner shipping. Trade off between air pollution, costs and refinery CO2 emissions

    International Nuclear Information System (INIS)

    De Wilde, H.P.J.; Kroon, P.

    2008-05-01

    Still subject to final approval in October 2008, the International Maritime Organisation (IMO) agreed on a maximum sulphur content of 0.5% for shipping fuels in 2020. This target will induce major changes in the global refinery industry. We have estimated the impact on the Dutch refinery industry, which annually produces about 8 million tons of heavy fuel oil for sea shipping, with refinery residues as main component. It is technically possible to convert all residues, although this process will cause an additional energy use of about one million tons of crude oil and a related CO2 emission of about 4 million tons. The investment costs for these major changes in the Dutch refinery industry are estimated at about 1.5 tot 2 billion euros. The recent IMO agreement enables a gradual introduction of cleaner shipping fuels, which will reduce market disruptions and peak prices. Nevertheless, Rotterdam may not necessarily be able to develop a similar position in import, export and bunkering of future low sulphur fuels, compared to its present strong position in the market of heavy marine bunkers. Extrapolation of our national study to the global scale suggests that the deep conversion of 350 million tons of heavy fuel oil for shipping would require refinery investments in the order of 70-100 billion euros. The associated CO2 emissions would amount up to 175 Mton. The net additional CO2 emission, however, would be smaller since lighter shipping fuels result in less CO2 emissions at sea. On balance, we expect that the improvements in fuel economy, driven by the expensive low-carbon shipping fuels, will decrease CO2 emissions more than the increase in CO2 emissions from additional desulphurization in the refineries. Nevertheless CO2 emissions from sea shipping will continue to increase since marine transport is rapidly growing

  19. Basic science and energy research sector profile: Background for the National Energy Strategy

    Energy Technology Data Exchange (ETDEWEB)

    March, F.; Ashton, W.B.; Kinzey, B.R.; McDonald, S.C.; Lee, V.E.

    1990-11-01

    This Profile report provides a general perspective on the role of basic science in the spectrum of research and development in the United States, and basic research's contributions to the goals of the National Energy Strategy (NES). It includes selected facts, figures, and analysis of strategic issues affecting the future of science in the United States. It is provided as background for people from government, the private sector, academia, and the public, who will be reviewing the NES in the coming months; and it is intended to serve as the basis for discussion of basic science issues within the context of the developing NES.

  20. Effect of adoption of gas turbine in oil refinery

    Energy Technology Data Exchange (ETDEWEB)

    Tamai, Hiroto

    1988-08-01

    With progress in energy saving, and increase in automation in facilities, the dependence on electric power increases relative steam power. Further in order to reduce the production cost, the adoption of gas turbine combined cycle system, mainly aimed at power generation, is considered to be most suitable. This adoption, accompanied with the utilization of refinery offgas, dresults in a reduction in unit power generation cost, by increasing the ratio of domestic power generation. The gas turbine using deethanizing tower offgas as main fuel and butane as auxillary fuel, the combined cycle system, where steam produced from the turbine waste heat boiler drives the existing back pressure turbine, was constituted. The generator is 118 kVA in capacity. Against the maximum power demand being 16,500 kWh in the oil refinery, the obtainment of 11,000 kWh by the gas turbine and 2,500 kWh by the back pressure turbine was assured, with a considerable lowering in power to be purchased. (7 figs, 1 tab, 1 ref)

  1. The regulation of uranium refineries and conversion facilities in Canada

    International Nuclear Information System (INIS)

    Didyk, J.P.

    1986-04-01

    The nuclear regulatory process as it applies to uranium refineries and conversion facilities in Canada is reviewed. In the early 1980s, Eldorado Resources Limited proposed to construct and operate new facilities for refining yellowcake and for the production of uranium hexafluoride (UF 6 ). These projects were subject to regulation by the Atomic Energy Control Board (AECB). A description of the AECB's comprehensive licensing process covering all stages of siting, construction, operation and eventual decommissioning of nuclear facilities is traced as it was applied to the Eldorado projects. The AECB's concern with occupational health and safety, with public health and safety and with the protection of the environment in so far as it affects public health and safety is emphasized. Some regulatory difficulties encountered during the project's development which led to opening up the licensing process to public input and closer coordination of regulatory activities with other provincial and federal regulatory agencies are described. The Board's regulatory operational compliance program for uranium refineries and conversion facilities is summarized

  2. Electrochemical removal of phenol from oil refinery wastewater.

    Science.gov (United States)

    Abdelwahab, O; Amin, N K; El-Ashtoukhy, E-S Z

    2009-04-30

    This study explores the possibility of using electrocoagulation to remove phenol from oil refinery waste effluent using a cell with horizontally oriented aluminum cathode and a horizontal aluminum screen anode. The removal of phenol was investigated in terms of various parameters namely: pH, operating time, current density, initial phenol concentration and addition of NaCl. Removal of phenol during electrocoagulation was due to combined effect of sweep coagulation and adsorption. The results showed that, at high current density and solution pH 7, remarkable removal of 97% of phenol after 2h can be achieved. The rate of electrocoagulation was observed to increase as the phenol concentration decreases; the maximum removal rate was attained at 30 mg L(-1) phenol concentration. For a given current density using an array of closely packed Al screens as anode was found to be more effective than single screen anode, the percentage phenol removal was found to increase with increasing the number of screens per array. After 2h of electrocoagulation, 94.5% of initial phenol concentration was removed from the petroleum refinery wastewater. Energy consumption and aluminum Electrode consumption were calculated per gram of phenol removed. The present study shows that, electrocoagulation of phenol using aluminum electrodes is a promising process.

  3. 40 CFR 80.94 - Requirements for gasoline produced at foreign refineries.

    Science.gov (United States)

    2010-07-01

    ... inspection or audit if a baseline petition has not been approved, and any work papers related to refinery... foreign refineries. 80.94 Section 80.94 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... for gasoline produced at foreign refineries. (a) Definitions. (1) A foreign refinery is a refinery...

  4. Energy Profiles of an Agricultural Frontier: The American Great Plains, 1860-2000.

    Science.gov (United States)

    Cunfer, Geoff; Watson, Andrew; MacFadyen, Joshua

    2018-04-01

    Agro-ecosystem energy profiles reveal energy flows into, within, and out of U.S. Great Plains farm communities across 140 years. This study evaluates external energy inputs such as human labor, machinery, fuel, and fertilizers. It tracks the energy content of land produce, including crops, grazed pasture, and firewood, and also accounts unharvested energy that remains available for wildlife. It estimates energy redirected through livestock feed into draft power, meat, and milk, and estimates the energy content of final produce available for local consumption or market sale. The article presents energy profiles for three case studies in Kansas in 1880, 1930, 1954, and 1997. Two energy transformations occurred during that time. The first, agricultural colonization , saw farm communities remake the landscape, turning native grassland into a mosaic of cropland and pasture, a process that reduced overall landscape energy productivity. A second energy transition occurred in the mid-twentieth century, characterized by fossil fuel energy imports. That outside energy raised harvested and unharvested energy flows, reused biomass energy, and also final produce. This socio-ecological transition increased landscape energy productivity by 33 to 45 percent above pre-settlement conditions in grain-growing regions. These energy developments were not uniform across the plains. Variations in rainfall and soil quality constrained or favored energy productivity in different places. The case studies reveal the spatial variation of energy profiles in Great Plains agro-ecosystems, while the longitudinal approach tracks temporal change.

  5. The acid refinery wastes in environment

    International Nuclear Information System (INIS)

    Samesova, D.; Ladomersky, J.; Hroncova, E.

    2003-01-01

    The aim of our paper is to assign ways and means of the pollution extension from the old landfills of the petrochemical sludges. In the past the sludges were deposited in sludge landfills. Nowadays remediation of the landfills is a key problem. We analyse condition of the refinery sludges latching. We found out the meaning influences of leachate time, temperature, concentration and liquid kind. (authors)

  6. Opportunities for Biorenewables in Oil Refineries

    Energy Technology Data Exchange (ETDEWEB)

    Marker, T.L.

    2005-12-19

    Abstract: The purpose of this study was to evaluate the potential for using biorenewable feedstocks in oil refineries. Economic analyses were conducted, with support from process modeling and proof of principle experiments, to assess a variety of potential processes and configurations. The study considered two primary alternatives: the production of biodiesel and green diesel from vegetable oils and greases and opportunities for utilization of pyrolysis oil. The study identified a number of promising opportunities for biorenewables in existing or new refining operations.

  7. Metal leaching from refinery waste hydroprocessing catalyst.

    Science.gov (United States)

    Marafi, Meena; Rana, Mohan S

    2018-05-18

    The present study aims to develop an eco-friendly methodology for the recovery of nickel (Ni), molybdenum (Mo), and vanadium (V) from the refinery waste spent hydroprocessing catalyst. The proposed process has two stages: the first stage is to separate alumina, while the second stage involves the separation of metal compounds. The effectiveness of leaching agents, such as NH 4 OH, (NH 4 ) 2 CO 3 , and (NH 4 ) 2 S 2 O 8 , for the extraction of Mo, V, Ni, and Al from the refinery spent catalyst has been reported as a function of reagent concentration (0.5 to 2.0 molar), leaching time (1 to 6 h), and temperature (35 to 60°C). The optimal leaching conditions were achieved to obtain the maximum recovery of Mo, Ni, and V metals. The effect of the mixture of multi-ammonium salts on the metal extraction was also studied, which showed an adverse effect for Ni and V, while marginal improvement was observed for Mo leaching. The ammonium salts can form soluble metal complexes, in which stability or solubility depends on the nature of ammonium salt and the reaction conditions. The extracted metals and support can be reused to synthesize a fresh hydroprocessing catalyst. The process will reduce the refinery waste and recover the expensive metals. Therefore, the process is not only important from an environmental point of view but also vital from an economic perspective.

  8. First refinery opened in Kyrgyz Republic

    International Nuclear Information System (INIS)

    Anon.

    1996-01-01

    The first oil refinery in the Kyrgyz Republic was opened on 5 October 1996 in Jalalabad in a ceremony attended by the President of the Central Asian country, Askar Akaev. The 10,000 barrels of oil per day (bopd) modular refinery has been financed by the Canadian oil junior, Kyrgoil Corporation, which has also formed a joint venture with the national oil company, Kyrgyzneft, to redevelop where viable the 628 underperforming oil wells in the Kyrgyz Republic sector of the Fergana Basin. The opening is the first significant milestone in a programme initiated by Akaev to develop the oil production industry in the Kyrgyz Republic. Currently the country imports more than 50,000 barrels of oil equivalent per day, mostly from Kazakhstan. In the year ending March 1996, 110 million was spent on imports of fuel products, an amount that exceeds the trade deficit over the same period. Built in only eight months, the Pound 12 million refinery will gradually be brought to full capacity. By January, it is expected that more than 5,000 barrels of gasoline, diesel and fuel oil will be produced every day. Although there is some crude oil in storage, the ramping of production is tied into the programme of workovers of the existing wells. There are no current plans to import crude, although most of the infrastructure is in place should it become necessary. (author)

  9. Ranking environmental liabilities at a petroleum refinery

    International Nuclear Information System (INIS)

    Lupo, M.

    1995-01-01

    A new computer model is available to allow the management of a petroleum refinery to prioritize environmental action and construct a holistic approach to remediation. A large refinery may have numerous solid waste management units regulated by the Resource Conservation and Recovery Act (RCRA), as well as process units that emit hazardous chemicals into the environment. These sources can impact several environmental media, potentially including the air, the soil, the groundwater, the unsaturated zone water, and surface water. The number of chemicals of concern may be large. The new model is able to rank the sources by considering the impact of each chemical in each medium from each source in terms of concentration, release rate, and a weighted index based on toxicity. In addition to environmental impact, the sources can be ranked in three other ways: (1) by cost to remediate, (2) by environmental risk reduction caused by the remediation in terms of the decreases in release rate, concentration, and weighted index, and (3) by cost-benefit, which is the environmental risk reduction for each source divided by the cost of the remedy. Ranking each unit in the refinery allows management to use its limited environmental resources in a pro-active strategic manner that produces long-term results, rather than in reactive, narrowly focused, costly, regulatory-driven campaigns that produce only short-term results

  10. Amoco/Environmental Protection Agency Pollution Prevention Project, Yorktown refinery. Refinery release inventory. Final report

    International Nuclear Information System (INIS)

    Klee, H.; Kizier, G.J.; Baloo, S.; Hockman, E.L.; Couzens-Roberts, C.

    1992-07-01

    The report volume summarizes physical data obtained during a 2-year pollution prevention study of Amoco Oil Company's Yorktown Virginia Refinery. The study was jointly sponsored as a cooperative effort of Amoco Corporation and the United States Environmental Protection Agency. A multi-media sampling program was used to identify potential pollution sources within the Refinery. Sampling and analysis included air, surface water, groundwater, and solid waste data. Public perceptions about environmental issues of concern in the vicinity of the Refinery were also surveyed. The inventory showed that nearly 99 percent of the releases were airborne at the facility. Most of the remainder involved land disposal of solid wastes. Specific sources of major pollutants are identified

  11. Operation : motor city : Michigan's only refinery to handle an increased slate of heavy Canadian crude

    International Nuclear Information System (INIS)

    Jaremko, D.

    2008-01-01

    A planned $1.9 billion upgrade and expansion will see a Detroit, Michigan refinery producing nearly 100 per cent Canadian crude oil. The upgrade will have important social, economic, and environmental implications for the oil sands industry, and is being seen as an important step for the future of the entire energy industry. The site was selected after a consultation of pipeline routes in North America. The refinery's coking capacity will help to ease the market constraints that Canadian crude is currently facing in the United States. The Midwest downstream oil and gas industry is well-positioned to help maximize the value of Canada's bitumen resources. In addition to expanding processing facilities, the refinery will also add capacity of approximately 15,000 barrels per day, as well as a delayed coker, sulphur recovery complex, ultra-low nitrogen oxide (NO x ) burners, a 33,000 barrel-per-day distillate hydrotreater, and a hydrogen plant. It was concluded that construction of the refinery will be completed by 2010. 2 figs

  12. The impact of CO2 taxation on the configuration of new refineries: An application to Brazil

    International Nuclear Information System (INIS)

    Gomes, Gabriel Lourenco; Szklo, Alexandre; Schaeffer, Roberto

    2009-01-01

    This article evaluates the impact of pricing CO 2 emissions over the configuration of new refinery complexes in their conceptual phase. Two refineries' schemes were simulated through a linear programming optimization model in order to compare the optimum configuration obtained before and after the input of different CO 2 prices. The cases analyzed represent refining projects to be located in Brazil, a growing market for fuels and petrochemical feedstocks, as well as an oil producing country with rising crude exports. After 2012, emerging countries, such as Brazil, may adopt carbon emission reduction targets. Therefore, it is worth analyzing the impact of pricing CO 2 emissions in these countries, where the majority of new refining projects will be located. Our findings indicate that the initial refinery configurations proposed are quite rigid technologically for CO 2 prices up to US$ 100/t CO 2 . For CO 2 prices higher than US$ 100/t CO 2 , refineries reduced their emissions by increasing the consumption of natural gas used to produce hydrogen, and through changes in the original configurations towards less-energy consuming process units. Promising technological advances, such as carbon capture and storage (CCS), can also diminish the rigidity of the model and facilitate actions to curb carbon emissions.

  13. Carbon flow analysis and Carbon emission reduction of FCC in Chinese oil refineries

    Science.gov (United States)

    Jia, Fengrui; Wei, Na; Ma, Danzhu; Liu, Guangxin; Wu, Ming; Yue, Qiang

    2017-08-01

    The major problem of the energy production in oil refineries is the high emission of CO2 in China. The fluid catalytic cracking unit (FCC) is the key source of carbon emission in the oil refineries. According to the statistical data, the carbon emission of FCC unit accounts for more than 31% for the typical oil refineries. The carbon flow of FCC in the typical Chinese oil refineries were evaluated and analysed, which aimed at the solution of CO2 emission reduction. The method of substances flow analysis (SFA) and the mathematical programming were used to evaluate the carbon metabolism and optimize the carbon emission. The results indicated that the combustion emission of the reaction-regeneration subsystem (RRS) was the major source of FCC. The quantity of CO2 emission of RSS was more than 90%. The combustion efficiency and the amount of residual oil affected the carbon emission of RRS most according to the optimized analysis of carbon emission reduction. Moreover, the fractionation subsystem (TFS) had the highest environmental efficiency and the absorption-stabilization subsystem (ASS) had the highest resource efficiency (approximately to 1) of carbon.

  14. Profitability diagnosis of refinery and improvement proposal; Seiyusho no shueki shindan to kaizen teian

    Energy Technology Data Exchange (ETDEWEB)

    Aoyama, H.

    2000-07-01

    Based on consulting service RPS-J under joint operation of Nikki, UOP LLC of U.S.A. and Nikki Universal, approaching ways applied for profitability improvement and improvement proposal for refineries and analyzing techniques used for resolution of process bottlenecks were described. In RPS-J, themes of (1) energy saving, (2) quality upgrading, (3) improvement of disintegrating ratio, (4) reduction of give-away, (5) improvement of equipment operation ratio, (6) reduction of maintenance cost, (7) effective utilization of catalysts, are considered for profitability improvement fields. Procedures from idea excavation for profitability improvement to realization of profitability improvement are carried out in the order of, (1) Grasping of the present state, (2) Excavation of improving items and selection, (3) Quantitative evaluation of draft profitability improvement plan and focusing, (4) Profitability improvement by operation improvement, (5) Profitability improvement by minor improvement, (6) Profitability improvement in middle- and long-term vision, (7) Final focusing by feasibility study. Afterwards, examination to economically solve bottlenecks of critical facilities, examination on bottlenecks of distillation tower and refining tower and utility analysis are carried out. RPS-J was already applied to 4 refineries including Muroran Refinery and Negishi Refinery of Nisseki Mitsubishi, and profitability improvement themes were found to improve profitability of 50 to 150 cents per barrel. (NEDO)

  15. Life-cycle assessment of a waste refinery process for enzymatic treatment of municipal solid waste

    DEFF Research Database (Denmark)

    Tonini, Davide; Astrup, Thomas

    2012-01-01

    for the enzymatic treatment of municipal solid waste (MSW) is presented. The refinery produced a liquid (liquefied organic materials and paper) and a solid fraction (non-degradable materials) from the initial waste. A number of scenarios for the energy utilization of the two outputs were assessed. Co......Decrease of fossil fuel dependence and resource saving has become increasingly important in recent years. From this perspective, higher recycling rates for valuable materials (e.g. metals) as well as energy recovery from waste streams could play a significant role substituting for virgin material...... production and saving fossil resources. This is especially important with respect to residual waste (i.e. the remains after source-separation and separate collection) which in Denmark is typically incinerated. In this paper, a life-cycle assessment and energy balance of a pilot-scale waste refinery...

  16. Testing and comparison of lidars for profile and turbulence measurements in wind energy

    International Nuclear Information System (INIS)

    Courtney, M; Wagner, R; Lindeloew, P

    2008-01-01

    Lidar profilers are beginning to gain a foothold in wind energy. Both of the currently available commercially systems have been extensively tested at the Hovsore facility in Denmark and valuable insights have been gained. The extensively instrumented facility will be described and some examples of the results given, illustrating the strength and weaknesses of the two contrasting profilers

  17. Regional profile, energy-impacted communities: Region VIII

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-03-01

    This report has data on population, administration, finance, housing, health and safety, human services, education, and water and sewage for 325 energy-impacted communities. A review of current and potential energy developments in the region shows over 900 energy resource impacts listed for the 325 impacted communities. Coal development represents over one-third of the developments listed. Communities reporting coal development are distributed as follows: Colorado (36), Montana (42), North Dakota (61), South Dakota (13), Utah (73), and Wyoming (35). Energy-conversion initiatives represent another high incidence of energy-resource impact, with uranium development following closely with 83 communities reporting uranium development impact in the region. These projections indicate continued development of regional energy resources to serve national energy requirements. The 325 impacted communities as reported: Colorado (46), Montana (73), North Dakota (62), South Dakota (21), Utah (80), and Wyoming (43) follow a distribution pattern similar to that of future projects which illustrates that no area of the region will escape the impacts of energy development. (ERA citation 04:041706)

  18. Evaluation of treatment efficiency of processes for petroleum refinery`s wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Kee, Kean Chin [National Univ. of Singapore, Kent Ridge (Singapore). Dept. of Civil Engineering

    1993-12-31

    Processes used in the treatment of a petroleum refinery wastewater included initial API oil separator to be followed by dissolved air flotation and extended aeration system. The use of extended aeration biological system proved to be an improvement but not a solution yet in such kind of treatment. 2 refs., 2 tabs.

  19. Evaluation of treatment efficiency of processes for petroleum refinery`s wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Kee, Kean Chin [National Univ. of Singapore, Kent Ridge (Singapore). Dept. of Civil Engineering

    1994-12-31

    Processes used in the treatment of a petroleum refinery wastewater included initial API oil separator to be followed by dissolved air flotation and extended aeration system. The use of extended aeration biological system proved to be an improvement but not a solution yet in such kind of treatment. 2 refs., 2 tabs.

  20. Performance profiles of major energy producers 1995, January 1997

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-02-01

    This publication examines developments in the operations of the major U.S. energy-producing companies on a corporate level, by major line of business, by major function within each line of business, and by geographic area.

  1. Performance profiles of major energy producers 1995, January 1997

    International Nuclear Information System (INIS)

    1997-01-01

    This publication examines developments in the operations of the major U.S. energy-producing companies on a corporate level, by major line of business, by major function within each line of business, and by geographic area

  2. Energy deposition profile on ISOLDE Beam Dumps by FLUKA simulations

    CERN Document Server

    Vlachoudis, V

    2014-01-01

    In this report an estimation of the energy deposited on the current ISOLDE beam dumps obtained by means of FLUKA simulation code is presented. This is done for both ones GPS and HRS. Some estimations of temperature raise are given based on the assumption of adiabatic increase from energy deposited by the impinging protons. However, the results obtained here in relation to temperature are only a rough estimate. They are meant to be further studied through thermomechanical simulations using the energyprofiles hereby obtained.

  3. 40 CFR 80.1141 - Small refinery exemption.

    Science.gov (United States)

    2010-07-01

    .... (a)(1) Gasoline produced at a refinery by a refiner, or foreign refiner (as defined at § 80.1165(a... effective beginning on January 1 of the following calendar year, at which point the gasoline produced at... from the calculation of its Renewable Volume Obligation (under § 80.1107(a)) gasoline from any refinery...

  4. environmental impact of illegal refineries on the vegetation

    African Journals Online (AJOL)

    Dr. O. M. Adesope

    impact of illegal oil refineries in the Niger Delta, Nigeria, the floristic composition of the fresh water swamp forest at refining sites in two river systems and a brackish ... ecosystem of Rivers State, five species of Mangroves and two species of ... Visual observation was made along the Rivers to identify illegal refinery stations.

  5. Influence of an imperfect energy profile on a seeded free electron laser performance

    Directory of Open Access Journals (Sweden)

    Botao Jia

    2010-06-01

    Full Text Available A single-pass high-gain x-ray free electron laser (FEL calls for a high quality electron bunch. In particular, for a seeded FEL amplifier and for a harmonic generation FEL, the electron bunch initial energy profile uniformity is crucial for generating an FEL with a narrow bandwidth. After the acceleration, compression, and transportation, the electron bunch energy profile entering the undulator can acquire temporal nonuniformity. We study the influence of the electron bunch initial energy profile nonuniformity on the FEL performance. Intrinsically, for a harmonic generation FEL, the harmonic generation FEL in the final radiator starts with an electron bunch having energy modulation acquired in the previous stages, due to the FEL interaction at those FEL wavelengths and their harmonics. The influence of this electron bunch energy nonuniformity on the harmonic generation FEL in the final radiator is then studied.

  6. Person and consumption profiles. Building integrated energy supply; Person- og forbrugsprofiler. Bygningsintegreret energiforsyning

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, Rasmus L.; Noergaard, J.; Daniels, O.; Justesen, R.O.

    2011-08-15

    In the future, buildings will not only act as consumers of energy but as producers as well. For these ''prosumers'', energy production by use of solar panels, photovoltaics and heat pumps etc will be essential. The objective of this project was to find the most optimal combinations of building insulation and use of renewable energy sources in existing buildings in terms of economics and climate impacts. Five houses were analyzed based on different personal load, consumption profiles, solar orientation and proposed building envelope improvements and use of combinations of renewable energy systems. The present report describes how person and consumption profiles used in this project are developed, and which data that form the basis for these profiles. The increasing requirements for energy in the building sector mean that the primary energy consumption ends close to or below zero within the next years. Therefore, the consumption in buildings becomes a relatively larger and larger part of the total energy demand in dwellings. It is important to investigate whether there are seasonal distributions of power and water consumption, because it might give a more exact result and describe the reality better than by using yearly values. First, the personal load determined, and then humidity and consumption of both power and hot water is defined. Second, the hourly profiles are developed based on analyses of seasonal distributions. These profiles also include cold domestic water to see whether there is a correlation between this and hot domestic water. (ln)

  7. Petroleum Refinery Effluents Treatment by Advanced Oxidation Process with Methanol

    Energy Technology Data Exchange (ETDEWEB)

    Shoucheng, Wen [Yangtze Univ., HuBei Jingzhou (China)

    2014-02-15

    Petroleum refinery effluents are waste originating from industries primarily engaged in refining crude oil. It is a very complex compound of various oily wastes, water, heavy metals and so on. Conventional processes are unable to effectively remove the chemical oxygen demand (COD) of petroleum refinery effluents. Supercritical water oxidation (SCWO) was proposed to treat petroleum refinery effluents. In this paper, methanol was used to investigate co-oxidative effect of methanol on petroleum refinery effluents treatment. The results indicated that supercritical water oxidation is an effective process for petroleum refinery effluents treatment. Adding methanol caused an increase in COD removal. When reaction temperature is 440 .deg. C, residence time is 20 min, OE is 0.5 and initial COD is 40000 mg/L, and COD removal increases 8.5%.

  8. Two refineries running crude; third to restart by September

    International Nuclear Information System (INIS)

    Tippee, B.

    1993-01-01

    Kuwait's downstream oil and gas industry, which sustained less damage than the country's oil field infrastructure during the Iraqi occupation of the 1990-91, has nearly completed reconstruction. Two of three refineries have resumed operations, one of them at reduced crude distillation rates. And state-owned Kuwait National Petroleum Co. hopes to put the other refinery, Shuaiba, back on stream in September, although not at preinvasion throughput rates. Major reconstruction will be complete by year end, with crude oil distillation capacity at 650,000 b/sd. Preinvasion crude capacities of Kuwait's refineries totaled 840,000 b/d. The article describes an overview of the recovery; the status of the Mina Abdulla processing plant, the Mina Al-Ahmadi refinery, and the Shuaiba refinery; modernization plans, and plans for petrochemicals

  9. Petroleum Refinery Effluents Treatment by Advanced Oxidation Process with Methanol

    International Nuclear Information System (INIS)

    Shoucheng, Wen

    2014-01-01

    Petroleum refinery effluents are waste originating from industries primarily engaged in refining crude oil. It is a very complex compound of various oily wastes, water, heavy metals and so on. Conventional processes are unable to effectively remove the chemical oxygen demand (COD) of petroleum refinery effluents. Supercritical water oxidation (SCWO) was proposed to treat petroleum refinery effluents. In this paper, methanol was used to investigate co-oxidative effect of methanol on petroleum refinery effluents treatment. The results indicated that supercritical water oxidation is an effective process for petroleum refinery effluents treatment. Adding methanol caused an increase in COD removal. When reaction temperature is 440 .deg. C, residence time is 20 min, OE is 0.5 and initial COD is 40000 mg/L, and COD removal increases 8.5%

  10. Impact of PAH [Polycyclic Aromatic Hydrocarbons] outlets from an oil refinery on the receiving water area - sediment trap fluxes and multivariate statistical analysis

    International Nuclear Information System (INIS)

    Pettersen, Harald; Naef, Carina; Broman, Dag

    1997-01-01

    PAH concentrations (15 compounds) in settling particulate matter (SPM) collected in the waters outside a petroleum refinery on the Swedish Baltic coast, and in samples of particulate and dissolved fractions in the wastewater from the refinery were determined. SPM concentrations varied between 550 and 4250 ng x gdw -1 and the corresponding calculated fluxes varied between 0.1 and 3.7 ng x cm -2 x day -1 . Both concentrations and fluxes did not differ significantly from background coastal or offshore locations in the Baltic. PAH profiles of the SPM samples were compared with the wastewater samples and SPM samples from background areas in the Baltic, using pattern recognition techniques. This analysis showed that the SPM samples from the petroleum refinery displayed a PAH composition similar to that found in background reference sites in the Baltic, and that the SPM samples could not be connected to the wastewater samples from the refinery. This indicates that Nynas AB is not a significant source of PAHs to the waters in its immediate surroundings, i.e. the waters in the Nynashamn area, and/or that the hydraulic residence time of the water outside the refinery is low. A budget calculation showed that the wastewater outlet from Nynas AB is only a minor contributor of the PAH load to the waters outside the refinery. (Author)

  11. Report on the survey in fiscal 1998. Basic survey on promotion of the joint implementation (energy saving project for the Baku and Nobo-Baku refineries in Azerbaidjan); 1998 nendo chosa hokokusho. Kyodo jisshi nado suishin kiso chosa (Azerbaidjan Baku/Nobo-Baku seiyusho shoene project)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to promote the COP3 joint implementation with the Baku and Nobo-Baku refineries in Azerbaidjan Republic, a basic survey was carried out on energy saving measures for the heat exchange systems, fired heaters, and FCC units. Carbon dioxide is discharged annually in the amount of 1.1 million tons as the design value. Extensive overaging of the facilities has reduced the thermal efficiency to as low as 66%. Therefore, in order to recover motive power from the FCC units by improving the heat exchange systems and minimizing the fuel consumption of the fired heaters as low as possible, a draft modification method has been planned and rough design was made, including application of the modern energy saving technologies currently used in Japan. This has revealed that it is possible to reduce load on the fired heaters and assure the thermal efficiency of the entire boilers at 90%. Energy conservation can be realized on the heat exchange systems for crude distillation equipment operating at normal temperature, fired heaters and FCC units, producing carbon dioxide reduction effect of 600,000 tons annually. The Azerbaidjan side has very high interest in this project, intends to contribute to the project as the joint implementation parner, and expects technical and financial assistance from Japan. (NEDO)

  12. Energy infrastructure in India: Profile and risks under climate change

    DEFF Research Database (Denmark)

    Garg, Amit; Naswa, Prakriti; Shukla, P.R.

    2015-01-01

    risks to energy infrastructures in India and details two case studies - a crude oil importing port and a western coast railway transporting coal. The climate vulnerability of the port has been mapped using an index while that of the railway has been done through a damage function for RCP 4.5.0 and 8.......5 scenarios. Our analysis shows that risk management through adaptation is likely to be very expensive. The system risks can be even greater and might adversely affect energy security and access objectives. Aligning sustainable development and climate adaptation measures can deliver substantial co......-benefits. The key policy recommendations include: i) mandatory vulnerability assessment to future climate risks for energy infrastructures; ii) project and systemic risks in the vulnerability index; iii) adaptation funds for unmitigated climate risks; iv) continuous monitoring of climatic parameters...

  13. Raising the Profile of Energy Efficiency in China

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    Reducing standby power use in China. How much does China stand to gain from greater energy efficiency? The example of improved standby power efficiency in household appliances provides a useful indicator. IEA analysis projects that eight or nine 1-GW power plants could be struck off Chinas list of immediate capacity needs for the period to 2020 if energy-efficient standby devices were vigorously promoted. This impressive finding emerges from this paper. The paper reviews experience with tackling standby power consumption in OECD countries and models implementation of similar action in China and Shanghai. Its scenarios quantify the significant potential gains from standby power conservation campaigns and mandatory regulations.

  14. Reformulated gasoline: Costs and refinery impacts

    International Nuclear Information System (INIS)

    Hadder, G.R.

    1994-02-01

    Studies of reformulated gasoline (RFG) costs and refinery impacts have been performed with the Oak Ridge National Laboratory Refinery Yield Model (ORNL-RYM), a linear program which has been updated to blend gasolines to satisfy emissions constraints defined by preliminary complex emissions models. Policy makers may use the reformulation cost knee (the point at which costs start to rise sharply for incremental emissions control) to set emissions reduction targets, giving due consideration to the differences between model representations and actual refining operations. ORNL-RYM estimates that the reformulation cost knee for the US East Coast (PADD I) is about 15.2 cents per gallon with a 30 percent reduction of volatile organic compounds (VOCs). The estimated cost knee for the US Gulf Coast (PADD III) is about 5.5 cents per gallon with a VOC reduction of 35 percent. Reid vapor pressure (RVP) reduction is the dominant VOC reduction mechanism. Even with anti-dumping constraints, conventional gasoline appears to be an important sink which permits RFG to be blended with lower aromatics and sulfur contents in PADD III. In addition to the potentially large sensitivity of RFG production to different emissions models, RFG production is sensitive to the non-exhaust VOC share assumption for a particular VOC model. ORNL-RYM has also been used to estimate the sensitivity of RFG production to the cost of capital; to the RVP requirements for conventional gasoline; and to the percentage of RFG produced in a refining region

  15. A Personalised Profile-Based Intelligent and Adaptive Energy

    African Journals Online (AJOL)

    2015-05-11

    May 11, 2015 ... Increasing electronic waste has forced the mobile phone industry to move into a new era of energy ... Based on the information gathered, a mobile application, MoBateriE, was designed. ...... Thesis (PhD). Carnegie Mellon ...

  16. The outlook for renewable energy in Navarre: An economic profile

    International Nuclear Information System (INIS)

    Faulin, Javier; Lera, Fernando; Pintor, Jesus M.; Garcia, Justo

    2006-01-01

    This paper describes the outlook and development of renewable energy in Navarre (Spain), which has become one of the leading regions in renewables over the last 10 years. This paper focuses its attention on the key features of the energy policy in Navarre, where there has emerged a dynamic enterprise sector. This sector has enormously increased its employment rates in the region. The success of renewable energy in Navarre is the result of the joint impact of decisive institutional support, industrial initiatives and consensus among social agents with regard to renewables. Tax incentives and local investment programs designed to break down the reluctance of local authorities and a campaign to obtain public support have, moreover, proven more efficient than the prior feed-in tariffs scheme, designed to develop the renewable energy sector and create international companies within it. The paper culminates in a detailed prognosis based on the SRN2003 survey of employment and installed power, which covers the majority of the firms operating in the Navarre renewables sector. Findings, however, suggest that the future of the sector in Navarre could be held back by the shortage of trained workers. This article might serve as a pertinent example for the deployment of renewables at regional level worldwide

  17. Molecular dynamics simulations and free energy profile of ...

    Indian Academy of Sciences (India)

    aDepartment of Chemical Engineering, bDepartment of Chemistry, Amirkabir University of Technology,. 15875-4413 ... Lipid bilayers; Paracetamol; free energy; molecular dynamics simulation; membrane. 1. ..... bilayer is less favourable due to the hydrophobic nature .... Orsi M and Essex J W 2010 Soft Matter 6 3797. 54.

  18. Asynchronous event driven distributed energy management using profile steering

    NARCIS (Netherlands)

    Hoogsteen, G.; Molderink, A.; Hurink, J. L.; Smit, G. J. M.

    2017-01-01

    Distributed Energy Management methodologies with a scheduling approach based on predictions require means to avoid problems related to prediction errors. Various approaches deal with such prediction errors by applying a different online control mechanism, such as a double-sided auction. However,

  19. Energy efficiency and appliance purchases in Europe: Consumer profiles and choice determinants

    International Nuclear Information System (INIS)

    Gaspar, Rui; Antunes, Dalila

    2011-01-01

    This study seeks to the following: (1) understand the factors/characteristics typically considered when purchasing electrical appliances, (2) analyse the differences between consumer profiles regarding these and (3) understand the factors driving the consideration of energy efficiency class by purchasers. Results indicate a preference for first considering cost, followed by quality and energy consumption considerations. These are correlated positively with the consideration of energy efficiency class in consumer choices. Also, regression analysis shows environmental attitudes to be negative predictors of energy efficiency class consideration, while specific environmental behaviours were positive predictors. Finally, consumer profiles were identified based on gender, age and whether or not the purchaser was accompanied when decisions were made. Implications for retail employee training and the development of persuasive messages for consumers based on established profiles are discussed. - Highlights: → We assessed factors typically considered by consumers in electrical appliances choice. → Characteristics identified as most important for choice were as follows: cost, quality and energy consumption. → These correlated positively with the consideration of energy efficiency class. → Differences between consumer profiles regarding the characteristics consideration were identified. → Differences imply persuasive messages adaption to these, to increase energy class consideration.

  20. Household energy consumption in the United States, 1987 to 2009: Socioeconomic status, demographic composition, and energy services profiles

    Science.gov (United States)

    Kemp, Robert J.

    This dissertation examines household energy consumption in the United States over the period of 1987 to 2009, specifically focusing on the role of socioeconomic status, demographic composition, and energy services profiles. The dissertation makes use of four cross-sections from the Residential Energy Consumption Survey data series to examine how household characteristics influence annual energy consumption overall, and by fuel type. Chapter 4 shows that household income is positively related to energy consumption, but more so for combustible fuel consumption than for electricity consumption. Additionally, results for educational attainment suggest a less cross-sectional association and more longitudinal importance as related to income. Demographic composition matters, as predicted by the literature; household size and householder age show predicted effects, but when considered together, income explains any interaction between age and household size. Combustible fuels showed a far greater relationship to housing unit size and income, whereas electricity consumption was more strongly related to educational attainment, showing important differences in the associations by fuel type. Taken together, these results suggest a life course-based model for understanding energy consumption that may be strongly linked to lifestyles. Chapter 5 extends the findings in Chapter 4 by examining the patterning of physical characteristics and behaviors within households. The chapter uses Latent Class Analysis to examine a broad set of energy significant behaviors and characteristics to discover five unique energy services profiles. These profiles are uniquely patterned across demographic and socioeconomic compositions of households and have important effects on energy consumption. These profiles are likely byproducts of the lifestyles in which the household takes part, due to factors such as their socioeconomic status and household demographic composition. Overall, the dissertation

  1. Model etch profiles for ion energy distribution functions in an inductively coupled plasma reactor

    International Nuclear Information System (INIS)

    Chen, W.; Abraham-Shrauner, B.; Woodworth, J.R.

    1999-01-01

    Rectangular trench profiles are modeled with analytic etch rates determined from measured ion distribution functions. The pattern transfer step for this plasma etch is for trilayer lithography. Argon and chlorine angular ion energy distribution functions measured by a spherical collector ring analyzer are fit to a sum of drifting Maxwellian velocity distribution functions with anisotropic temperatures. The fit of the model ion distribution functions by a simulated annealing optimization procedure converges adequately for only two drifting Maxwellians. The etch rates are proportional to analytic expressions for the ion energy flux. Numerical computation of the etch profiles by integration of the characteristic equations for profile points and connection of the profiles points is efficient. copyright 1999 American Vacuum Society

  2. Ultra-shallow arsenic implant depth profiling using low-energy nitrogen beams

    International Nuclear Information System (INIS)

    Fearn, Sarah; Chater, Richard; McPhail, David

    2004-01-01

    Sputtering of silicon by low-energy nitrogen primary ion beams has been studied by a number of authors to characterize the altered layer, ripple formation and the sputtered yields of secondary ions [Surf. Sci. 424 (1999) 299; Appl. Phys. A: Mater. Sci. Process 53 (1991) 179; Appl. Phys. Lett. 73 (1998) 1287]. This study examines the application of low-energy nitrogen primary ion beams for the possible depth profiling of ultra-shallow arsenic implants into silicon. The emphasis of this work is on the matrix silicon signals in the pre-equilibrium surface region that are used for dose calibration. Problems with these aspects of the concentration depth profiling can give significant inconsistencies well outside the error limits of the quoted dose for the arsenic implantation as independently verified by CV profiling. This occurs during depth profiling with either oxygen primary ion beams (with and without oxygen leaks) or cesium primary ion beams

  3. Ultra-low energy Ar+ beam applied for SIMS depth profile analysis of layered nanostructures

    International Nuclear Information System (INIS)

    Konarski, P.; Mierzejewska, A.; Iwanejko, I.

    2001-01-01

    Secondary ion mass spectrometry (SIMS) depth profile analyses of flat layered nanostructures: 10 nm Ta 2 O 3 /Ta and 20 nm (10 x B 4 C/Mo)/Si as well as microparticles of core (illite) - shell (rutile) structure, performed with the use of ultra-low energy ion beam (180-880 eV, Ar + ), are presented. The profiles were obtained using 'mesa' scanning technique and also sample rotation. Depth profile resolution below 1 nanometer was obtained for flat nanostructures. Presented experimental results are compared with Monte Carlo sputtering simulations of analysed structures. A method of finding beam energy, optimal for the best resolution SIMS depth profile analysis, is suggested. (author)

  4. Well-to-Wheels Greenhouse Gas Emission Analysis of High-Octane Fuels with Ethanol Blending: Phase II Analysis with Refinery Investment Options

    Energy Technology Data Exchange (ETDEWEB)

    Han, Jeongwoo [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division; Wang, Michael [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division; Elgowainy, Amgad [Argonne National Lab. (ANL), Argonne, IL (United States). Energy Systems Division; DiVita, Vincent [Jacobs Consultancy Inc., Houston, TX (United States)

    2016-08-01

    Higher-octane gasoline can enable increases in an internal combustion engine’s energy efficiency and a vehicle’s fuel economy by allowing an increase in the engine compression ratio and/or by enabling downspeeding and downsizing. Producing high-octane fuel (HOF) with the current level of ethanol blending (E10) could increase the energy and greenhouse gas (GHG) emissions intensity of the fuel product from refinery operations. Alternatively, increasing the ethanol blending level in final gasoline products could be a promising solution to HOF production because of the high octane rating and potentially low blended Reid vapor pressure (RVP) of ethanol at 25% and higher of the ethanol blending level by volume. In our previous HOF well-to-wheels (WTW) report (the so-called phase I report of the HOF WTW analysis), we conducted WTW analysis of HOF with different ethanol blending levels (i.e., E10, E25, and E40) and a range of vehicle efficiency gains with detailed petroleum refinery linear programming (LP) modeling by Jacobs Consultancy and showed that the overall WTW GHG emission changes associated with HOFVs were dominated by the positive impact associated with vehicle efficiency gains and ethanol blending levels, while the refining operations to produce gasoline blendstock for oxygenate blending (BOB) for various HOF blend levels had a much smaller impact on WTW GHG emissions (Han et al. 2015). The scope of the previous phase I study, however, was limited to evaluating PADDs 2 and 3 operation changes with various HOF market share scenarios and ethanol blending levels. Also, the study used three typical configuration models of refineries (cracking, light coking, and heavy coking) in each PADD, which may not be representative of the aggregate response of all refineries in each PADD to various ethanol blending levels and HOF market scenarios. Lastly, the phase I study assumed no new refinery expansion in the existing refineries, which limited E10 HOF production to the

  5. Sustainable biotechnology: sources of renewable energy

    National Research Council Canada - National Science Library

    Singh, Om V; Harvey, Steven P

    2010-01-01

    ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Anuj K. Chandel, Om V. Singh, and L.Venkateswar Rao 63 Tactical Garbage to Energy Refinery (TGER) . . . . . . . . . . . . . . . James J. Valdes and Jerry B. Warner...

  6. Treatment of Tehran refinery wastewater using rotating biological contactor

    Energy Technology Data Exchange (ETDEWEB)

    Ghazi, Masoud; Mirsajadi, Hassan; Ganjidoust, Hossien [Tarbeyat Modarres Univ., Teheran (Iran, Islamic Republic of). Environmental Engineering Dept.

    1993-12-31

    Tehran Refinery is a large plant which produces several petroleum products. The wastewaters are generated from several different refinery processes and units. Because of the wastewaters uniqueness they need to be treated in each specific plant. Currently, an activated sludge system is the main biological wastewater treatment process in Tehran refinery plant. A study was initiated in order to find a more suitable and reliable process which can produce a better treated effluent which might, in case the process be successful, be reused for irrigation lands. 5 refs., 5 figs.

  7. Api Energia IGCC plant is fully integrated with refinery

    Energy Technology Data Exchange (ETDEWEB)

    Del Bravo, R. [api Energia, Rome (Italy); Trifilo, R. [ABB Sadelmi, Milan (Italy); Chiantore, P.V. [api anonima petroli Italiania Spa, Rome (Italy); Starace, F. [ABB Power Generation, Baden (Switzerland); O`Keefe, L.F. [Texico, White Plains (United States)

    1998-06-01

    The api Energia integrated gasification combined cycle (IGCC) plant being built at Falconara Marittima, on Italy`s Adriatic coast, is one of the three IGCC plants under construction in Italy following the liberalization of the electricity production sector. The plant will take 59.2 t/h of high sulphur heavy oil produced by the Falconara refinery, convert it to syngas and use the gas to generate 280 MW of electricity, plus steam and other gases for use in the refinery. The IGCC plant will be highly integrated into the refining process, with a large number of interchanges between the IGCC unit and the rest of the refinery. (author)

  8. Treatment of Tehran refinery wastewater using rotating biological contactor

    Energy Technology Data Exchange (ETDEWEB)

    Ghazi, Masoud; Mirsajadi, Hassan; Ganjidoust, Hossien [Tarbeyat Modarres Univ., Teheran (Iran, Islamic Republic of). Environmental Engineering Dept.

    1994-12-31

    Tehran Refinery is a large plant which produces several petroleum products. The wastewaters are generated from several different refinery processes and units. Because of the wastewaters uniqueness they need to be treated in each specific plant. Currently, an activated sludge system is the main biological wastewater treatment process in Tehran refinery plant. A study was initiated in order to find a more suitable and reliable process which can produce a better treated effluent which might, in case the process be successful, be reused for irrigation lands. 5 refs., 5 figs.

  9. Refinery expansion and upgrading: Trends and needs

    International Nuclear Information System (INIS)

    Sloan, D.E.

    1993-01-01

    Much of the world's reserves of heavy, high sulfur crude oil are located in the western hemisphere. One may look from north to south and find these types of crudes. in Canada, there are the vast deposits of tar sands and other heavy oils. In the United States we find heavy, high sulfur crude in California's San joaquin Valley, the Rockies' shale oil deposits and in other areas. Moving south, Mexico's Maya crude is well known to refiners, as are the heavy crudes of Venezuela's Orinoco Belt. On the other hand, many refineries outside the United States are limited in their ability to handle heavy, high sulfur crudes either because of metallurgy or processing configurations

  10. Electrometallurgy of copper refinery anode slimes

    Science.gov (United States)

    Scott, J. D.

    1990-08-01

    High-selenium copper refinery anode slimes form two separate and dynamically evolving series of compounds with increasing electrolysis time. In one, silver is progressively added to non-stoichiometric copper selenides, both those originally present in the anode and those formed subsequently in the slime layer, and in the other, silver-poor copper selenides undergo a dis-continuous crystallographic sequence of anodic-oxidative transformations. The silver-to-selenium molar ratio in the as-cast anode and the current density of electrorefining can be used to construct predominance diagrams for both series and, thus, to predict the final bulk “mineralogy” of the slimes. Although totally incorrect in detail, these bulk data are sufficiently accurate to provide explanations for several processing problems which have been experienced by Kidd Creek Division, Falconbridge Ltd., in its commercial tankhouse. They form the basis for a computer model which predicts final cathode quality from chemical analyses of smelter feed.

  11. Basic principles of thermo-acoustic energy and temporal profile detection of microwave pulses

    CERN Document Server

    Andreev, V G; Vdovin, V A

    2001-01-01

    Basic principles of a thermo-acoustic method developed for the detection of powerful microwave pulses of nanosecond duration are discussed.A proposed method is based on the registration of acoustic pulse profile originated from the thermal expansion of the volume where microwave energy was absorbed.The amplitude of excited acoustic transient is proportional to absorbed microwave energy and its temporal profile resembles one of a microwave pulse when certain conditions are satisfied.The optimal regimes of microwave pulse energy detection and sensitivity of acoustic transient registration with piezo-transducer are discussed.It was demonstrated that profile of a microwave pulse could be detected with temporal resolution of 1 - 3 nanosecond.

  12. Beam-energy and laser beam-profile monitor at the BNL LINAC

    Energy Technology Data Exchange (ETDEWEB)

    Connolly, R.; Briscoe, B.; Degen, C.; DeSanto, L.; Meng, W.; Minty, M.; Nayak, S.; Raparia, D.; Russo, T.

    2010-05-02

    We are developing a non-interceptive beam profile and energy monitor for H{sup -} beams in the high energy beam transport (HEBT) line at the Brookhaven National Lab linac. Electrons that are removed from the beam ions either by laser photodetachment or stripping by background gas are deflected into a Faraday cup. The beam profile is measured by stepping a narrow laser beam across the ion beam and measuring the electron charge vs. transverse laser position. There is a grid in front of the collector that can be biased up to 125kV. The beam energy spectrum is determined by measuring the electron charge vs. grid voltage. Beam electrons have the same velocity as the beam and so have an energy of 1/1836 of the beam protons. A 200MeV H{sup -} beam yields 109keV electrons. Energy measurements can be made with either laser-stripped or gas-stripped electrons.

  13. Predicting Low Energy Dopant Implant Profiles in Semiconductors using Molecular Dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Beardmore, K.M.; Gronbech-Jensen, N.

    1999-05-02

    The authors present a highly efficient molecular dynamics scheme for calculating dopant density profiles in group-IV alloy, and III-V zinc blende structure materials. Their scheme incorporates several necessary methods for reducing computational overhead, plus a rare event algorithm to give statistical accuracy over several orders of magnitude change in the dopant concentration. The code uses a molecular dynamics (MD) model to describe ion-target interactions. Atomic interactions are described by a combination of 'many-body' and pair specific screened Coulomb potentials. Accumulative damage is accounted for using a Kinchin-Pease type model, inelastic energy loss is represented by a Firsov expression, and electronic stopping is described by a modified Brandt-Kitagawa model which contains a single adjustable ion-target dependent parameter. Thus, the program is easily extensible beyond a given validation range, and is therefore truly predictive over a wide range of implant energies and angles. The scheme is especially suited for calculating profiles due to low energy and to situations where a predictive capability is required with the minimum of experimental validation. They give examples of using the code to calculate concentration profiles and 2D 'point response' profiles of dopants in crystalline silicon and gallium-arsenide. Here they can predict the experimental profile over five orders of magnitude for <100> and <110> channeling and for non-channeling implants at energies up to hundreds of keV.

  14. Smart microgrids in refineries, Mexico case; Microrredes inteligentes en refinerias, caso Mexico

    Energy Technology Data Exchange (ETDEWEB)

    Estrada Garcia, Javier Alejandro; Linan Garcia, Roberto; Picasso Blanquel, Cuitlahuac; Silva Farias, Jose Luis [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

    2013-03-01

    In this paper we present the technological trends on smart microgrids for refineries, case Mexico. Distributed generation on refineries is a model of microgrid with great challenges to solve, considering renewable energy. Also it discusses the scenario in bidirectional connection from refineries to the utility supergrid Comision Federal de Electricidad (CFE by its acronym in Spanish) and how to reach the development of a smart microgrid. We look different scenarios in power systems refineries, and the feasibility to achieve and develop the technology concepts in smart grid, such as: demand response in real time, exchange of energy between microgrid with supergrid-CFE and viceversa, energy efficiency, microgrid automation, selfhealing/real time autorecovery fault in power systems, storage energy and its application on power systems blackout in refineries. Finally we discussed the concepts that represent the greatest challenges to be solved on the smart microgrids and consider obtaining alternatives solution in medium or long term. [Spanish] En este documento se presentan las tendencias tecnologicas en micro redes inteligentes para refinerias, en el caso de Mexico. La generacion distribuida en refinerias es un modelo de micro red con grandes desafios por resolver, considerando la energia renovable. Se analiza tambien el escenario en conexion bidireccional de refinerias a la super red de la Comision Federal de Electricidad (CFE), la empresa electrica mexicana, y como lograr el desarrollo de una micro red inteligente. Se consideran diferentes escenarios en refinerias de sistemas de potencia, y la factibilidad de alcanzar y desarrollar los conceptos de tecnologia en una red inteligente, tales como: respuesta de demanda en tiempo real, intercambio de energia entre la micro red con la super red de la CFE y viceversa, eficiencia de energia, automatizacion de micro redes, autorrecuperacion de fallas en autoarreglo/tiempo real. En sistemas de potencia, almacenamiento de

  15. Porte de Gascogne region - Energy-climate profile. Study of the potential in renewable energy and in energy management in five communes of the Porte de Gascogne region

    International Nuclear Information System (INIS)

    2013-03-01

    After a presentation of the studied territory, a recall of challenges related to climate change, a discussion of the role of Climate-Air-Energy Regional Schemes (SRCAE), this study reports an analysis of the territory vulnerability to climate change under different aspects (climate, biodiversity, water, agriculture, built environment, soil erosion, others). It draws the energy-climate profile of the region in terms of energy consumption and of vulnerability. These issues are then addressed per sector (housing, tertiary, agriculture, industry, transports, wastes, good consumption, tourism). Energy production is analysed (renewable energies, solar thermal, photovoltaic, wood, biomass, biogas, geothermal, combustion, bio-fuel). Scenarios are defined for energy saving, reduction of greenhouse gas emissions, renewable energy production, and carbon storage. An action plan is then defined. A second document reports studies of energy consumption, heritage, possibilities of development of renewable energies, and possibilities of development of positive energy building in the case of five communes (Fleurance, Gimont, Lectoure, Saint-Clar, and Samatan)

  16. Quantitative depth profiling of near surface semiconductor structures using ultra low energy SIMS analysis

    International Nuclear Information System (INIS)

    Elliner, D.I.

    1999-09-01

    The continual reduction in size of semiconductor structures and depths of junctions is putting a greater strain on characterization techniques. Accurate device and process modelling requires quantified electrical and dopant profiles from the topmost few nanometres. Secondary ion mass spectrometry (SIMS) is an analytical technique commonly used in the semiconductor industry to measure concentration depth profiles. To allow the quantification of the features that are closer to the surface, lower energy ions are employed, which also improves the available depth resolution. The development of the floating ion gun (FLIG) has made it possible to use sub keV beam energies on a routine basis, allowing quantified dopant profiles to be obtained within the first few nanometres of the surface. This thesis demonstrates that, when profiling with oxygen ion beams, greatest certainty in the retained dose is achieved at normal incidence, and when analysing boron accurate profile shapes are only obtained when the primary beam energy is less than half that of the implant. It was shown that it is now possible to profile, though with slower erosion rates and a limited dynamic range, with 100 eV oxygen (0 2 + ) ion beams. Profile features that had developed during rapid thermal annealing, that could only be observed when ultra low energy ion beams were used, were investigated using various analytical techniques. Explanations of the apparently inactive dopant were proposed, and included suggestions for cluster molecules. The oxide thickness of fully formed altered layers has also been investigated. The results indicate that a fundamental change in the mechanism of oxide formation occurs, and interfaces that are sharper than those grown by thermal oxidation can be produced using sub-keV ion beams. (author)

  17. Evaluation of energy absorption performance of steel square profiles with circular discontinuities

    Directory of Open Access Journals (Sweden)

    Dariusz Szwedowicz

    Full Text Available This article details the experimental and numerical results on the energy absorption performance of square tubular profile with circular discontinuities drilled at lengthwise in the structure. A straight profile pattern was utilized to compare the absorption of energy between the ones with discontinuities under quasi-static loads. The collapse mode and energy absorption conditions were modified by circular holes. The holes were drilled symmetrically in two walls and located in three different positions along of profile length. The results showed a better performance on energy absorption for the circular discontinuities located in middle height. With respect to a profile without holes, a maximum increase of 7% in energy absorption capacity was obtained experimentally. Also, the numerical simulation confirmed that the implementation of circular discontinuities can reduce the peak load (Pmax by 10%. A present analysis has been conducted to compare numerical results obtained by means of the finite element method with the experimental data captured by using the testing machine. Finally the discrete model of the tube with and without geometrical discontinuities presents very good agreements with the experimental results.

  18. Applying the new standards ISO-14000 in the implementation of the desalting process in the national system of refineries and its impact on energy consumption; Aplicacion de las nuevas normas ISO-14000, en la implementacion del desalado en el sistema nacional de refinerias y su impacto en el consumo de energia

    Energy Technology Data Exchange (ETDEWEB)

    Bazan, G.; Gonzalez, L. [Subgerencia de Investigacion Tecnologica, PEMEX-REFINACION, Mexico, D. F. (Mexico); Castillo, S.; Moran Pineda, M. [Gerencia de Investigacion Aplicada de Procesos, Instituto Mexicano del Petroleo Mexico, D. F. (Mexico)

    1997-12-31

    Every project has an objective, namely, it pursues results. A way of controlling a project is by defining a specific system in which its rules are the norms that form it and this is how, by means of these infrastructures, it is possible to systematize the technological as well as the administrative part of any type of project. In our specific case, the project consists in the application of Standards ISO-14000 in the implementation of the desalting process in the National System of Refineries, in order to optimize the process in relation to its chemical, analytical and rational use of energy aspects. [Espanol] Todo proyecto tiene un objetivo, es decir persigue resultados; una manera de controlar el desarrollo de un proyecto es definiendo un sistema especifico en el cual sus ordenadores son las normas que lo constituyen y es como mediante estas infraestructuras es posible sistematizar tanto en la parte tecnologica como en la administrativa de cualquier tipo de proyecto. En nuestro caso especifico el proyecto consiste en la aplicacion de las normas ISO-14000 en la implementacion del desalado en el Sistema Nacional de Refinerias, con el objeto de optimizar el proceso en lo relativo a sus aspectos quimicos, analiticos y uso racional de energia.

  19. Applying the new standards ISO-14000 in the implementation of the desalting process in the national system of refineries and its impact on energy consumption; Aplicacion de las nuevas normas ISO-14000, en la implementacion del desalado en el sistema nacional de refinerias y su impacto en el consumo de energia

    Energy Technology Data Exchange (ETDEWEB)

    Bazan, G; Gonzalez, L [Subgerencia de Investigacion Tecnologica, PEMEX-REFINACION, Mexico, D. F. (Mexico); Castillo, S; Moran Pineda, M [Gerencia de Investigacion Aplicada de Procesos, Instituto Mexicano del Petroleo Mexico, D. F. (Mexico)

    1998-12-31

    Every project has an objective, namely, it pursues results. A way of controlling a project is by defining a specific system in which its rules are the norms that form it and this is how, by means of these infrastructures, it is possible to systematize the technological as well as the administrative part of any type of project. In our specific case, the project consists in the application of Standards ISO-14000 in the implementation of the desalting process in the National System of Refineries, in order to optimize the process in relation to its chemical, analytical and rational use of energy aspects. [Espanol] Todo proyecto tiene un objetivo, es decir persigue resultados; una manera de controlar el desarrollo de un proyecto es definiendo un sistema especifico en el cual sus ordenadores son las normas que lo constituyen y es como mediante estas infraestructuras es posible sistematizar tanto en la parte tecnologica como en la administrativa de cualquier tipo de proyecto. En nuestro caso especifico el proyecto consiste en la aplicacion de las normas ISO-14000 en la implementacion del desalado en el Sistema Nacional de Refinerias, con el objeto de optimizar el proceso en lo relativo a sus aspectos quimicos, analiticos y uso racional de energia.

  20. Orbital momentum profiles and binding energy spectra for the complete valence shell of molecular fluorine

    International Nuclear Information System (INIS)

    Zheng, Y.; Brion, C.E.; Brunger, M.J.; Zhao, K.; Grisogono, A.M.; Braidwood, S.; Weigold, E.; Chakravorty, S.J.; Davidson, E.R.; Sgamellotti, A.; von Niessen, W.

    1996-01-01

    The first electronic structural study of the complete valence shell binding energy spectrum of molecular fluorine, encompassing both the outer and inner valence regions, is reported. These binding energy spectra as well as the individual orbital momentum profiles have been measured using an energy dispersive multichannel electron momentum spectrometer at a total energy of 1500 eV, with an energy resolution of 1.5 eV and a momentum resolution of 0.1 a.u. The measured binding energy spectra in the energy range of 14-60 eV are compared with the results of ADC(4) many-body Green's function and also direct-Configuration Interaction (CI) and MRSD-CI calculations. The experimental orbital electron momentum profiles are compared with SCF theoretical profiles calculated using the target Hartree-Fock approximation with a range of basis sets and with Density Functional Theory predictions in the target Kohn-Sham approximation with non-local potentials. The truncated (aug-cc-pv5z) Dunning basis sets were used for the Density Functional Theory calculations which also include some treatment of correlation via the exchange and correlation potentials. Comparisons are also made with the full ion-neutral overlap amplitude calculated with MRSD-CI wave functions. Large, saturated basis sets (199-GTO) were employed for both the high level SCF near Hartree-Fock limit and MRSD-CI calculations to investigate the effects of electron correlation and relaxation. 66 refs., 9 tabs., 9 figs

  1. Integration : OPEC is now in 35 foreign refineries

    International Nuclear Information System (INIS)

    Terzian, P.

    1994-01-01

    Seven countries from OPEC own now share holdings in 35 foreign refineries. By this process of downstream reintegration, these countries hope to reach a better stability of crude oil prices. (Author). 3 tabs

  2. Assessment of the effect of effluent discharge from coffee refineries ...

    African Journals Online (AJOL)

    Admin

    2Department of Environmental Health, Jimma University, Jimma, Ethiopia. ... cherries, transport them hydraulically through the pulping ..... Table 2. Interaction effects of effluent discharges by coffee refineries on physical characteristics between.

  3. Production, energy, and carbon emissions: A data profile of the iron and steel industry

    International Nuclear Information System (INIS)

    Battles, S.J.; Burns, E.M.; Adler, R.K.

    1999-01-01

    The complexities of the manufacturing sector unquestionably make energy-use analysis more difficult here than in other energy-using sectors. Therefore, this paper examines only one energy-intensive industry within the manufacturing sector--blast furnaces and steel mills (SIC 3312). SIC 3312, referred to as the iron and steel industry in this paper, is profiled with an examination of the products produced, how they are produced, and energy used. Energy trends from 1985 to 1994 are presented for three major areas of analysis. The first major area includes trends in energy consumption and expenditures. The next major area includes a discussion of energy intensity--first as to its definition, and then its measurement. Energy intensities presented include the use of different (1) measures of total energy, (2) energy sources, (3) end-use energy measures, (4) energy expenditures, and (5) demand indicators-economic and physical values are used. The final area of discussion is carbon emissions. Carbon emissions arise both from energy use and from certain industrial processes involved in the making of iron and steel. This paper focuses on energy use, which is the more important of the two. Trends are examined over time

  4. Valve automation in Indian refinery; Armaturenautomatisierung in indischer Raffinerie

    Energy Technology Data Exchange (ETDEWEB)

    Herbstritt, M. [AUMA Riester GmbH und Co. KG, Muellheim (Germany)

    2006-12-15

    The Mahul refinery near Mumbai is the third largest site of its kind in India. It is operated by BPCL, Bharat Petroleum Corporation Ltd. During the last few months, the refinery was extended. A plant for manufacturing motor lubricants was built, together with a tank farm for the products (LOBS = lube oil base stock). In April 2006 the new plant sections were put into operation. This article deals with the valve automation for this project. (orig.)

  5. Assessing refinery capacity and readiness to take Canadian product : is Canadian crude pushing or pulling?

    International Nuclear Information System (INIS)

    Friesner, J.M.

    2005-01-01

    This presentation addressed some of the challenges facing oil sands production in Canada. Refinery products and refining investments were discussed, as was the impact of alternative crude supply on the markets and pricing of oil sands. The oils sands products discussed include various qualities of sweet synthetic crude oil produced via upgraders; virgin and cracked intermediate products from oil sands upgraders; mined or Steam Assisted Gravity Drainage (SAGD) produced bitumen blended products; and synthetic heavy crude produced via hydrocracking. Products were listed in terms of ease of production, and a rationale for generic ranking was provided. A chart of 2003 characteristics of non-Canadian imports to the mid-west United States was provided. Various marketing strategies for different oil sands products were discussed, as well as issues concerning logistics. Strategies for the development of a bigger market include producer investment in refining capability; the acquisition of refining assets; investment in refiners' upgrading capability; and securing a long term supply deal. Core and extended markets for Western Canadian oil sands products were reviewed. A chart of North American refining capacity was presented. Details of a refinery with both coking and cracking capacity were examined. An increase in hydro processing capacity and expanded coking capacity, as well as an upgrade of metallurgy were suggested as possible upgrading options. Various refinery configurations were discussed in relation to lower cost feedstocks and clean fuels specifications. Issues concerning crude supply were examined with reference to pricing parity points and declines in traditional crude production. Specific supply issues concerning oil sands production were discussed, including transportation costs; adequate refining capacity; and availability of supply. Various logistic investments were considered. A map of BP's 5 U.S. refineries was presented. A forecast of expected changes in

  6. Development of radiological profiles for U.S. Department of Energy low-level mixed wastes

    International Nuclear Information System (INIS)

    Wilkins, B.D.; Meshkov, N.K.; Dolak, D.A.; Wang, Y.Y.

    1995-01-01

    Radiological profiles have been developed by Argonne National Laboratory for low-level mixed wastes (LLMWs) that are under the management of the US Department of Energy (DOE). These profiles have been used in the Office of Environmental Management Programmatic Environmental Impact Statement (EM PEIS) to support the analysis of environmental and health risks associated with the various waste management strategies. The radiological characterization of DOE LLMWs is generally inadequate and has made it difficult to develop a site- and waste-stream-dependent radiological profile for LLMWs. On the basis of the operational history of the DOE sites, a simple model was developed to generate site-dependent and waste-stream-independent radiological profiles for LLMWs. This paper briefly discusses the assumptions used in this model and the uncertainties in the results

  7. Taking inventory on VOC releases from Amoco's Yorktown refinery

    International Nuclear Information System (INIS)

    Klee, H.H. Jr.; Schmitt, R.E.; Harrass, M.C.; Podar, M.K.

    1996-01-01

    Amoco's Yorktown, Virginia, refinery is a 35-year-old, 53,000 bbl/day facility that manufacturers gasoline, heating oil, liquid petroleum gas, sulfur, and coke. In a cooperative and voluntary effort, Amoco Corporation and the US Environmental Protection Agency conducted a joint project to study pollution prevention opportunities at an operating industrial facility. Source reduction efforts--key to pollution prevention strategies--require knowledge of specific sources of releases. However, data on releases from individual process units are limited in favor of data to monitor existing end-of-pipe pollution control requirements. The study's sampling program sought to portray the distribution of releases within the refinery, their management within the refinery, and ultimate releases leaving the refinery. Subsequent tests of blowdown stack and fugitive emissions further improved total release estimates. The initial study estimated that the refinery generates about 25,000 metric tons (t)/year of potential pollutants. Of these, about half are released from the refinery as airborne, waterborne, or land-disposed releases. Airborne releases comprise the majority of releases by mass, about 12,000 t/year. Most of the airborne releases are volatile organic compound hydrocarbons. The inventory sampling project and subsequent work identified differences with Toxic Release Inventory (TRI) values and standard emission factors (AP-42). The inventory and other data provided an opportunity to consider options for, and limitations of, specific pollution prevention or source reduction strategies

  8. Assessment of Petroleum Leakage in Groundwater of the Abadan Refinery

    Directory of Open Access Journals (Sweden)

    Seyed Reza Shadizadeh

    2010-06-01

    Full Text Available Knowledge of petroleum leakage at oil refineries is vital for environmental study of water and soil pollution. Abadan Refinery is located between the Arvandrud and Bahmanshir rivers in the highly populated area of Abadan city. These rivers supply domestic, industrial, and agricultural water toAbadancity. During the war betweenIranandIraq, enormous volumes of oil and petroleum products leaked from storage tanks and pipelines at Abadan Refinery into the surrounding environment. The resulting pollution is a serious threat and a growing environmental concern for the region. In this work, twenty boreholes were dug to investigate petroleum leaks into the surrounding area both during and after the war. The thickness of petroleum floating on underground waters at the refinery was measured by sampling underground water over a period of one year along with measuring the piezometric heads of groundwater monitoring wells. Also, groundwater movement pattern at Abadan Refinery was determined by measuring the water table in each well over the same period. The results of sampling indicate that oil leaks were observed in just two wells; namely, wells No.3 and No.11. The results also show that the greatest portion of the oil spill in underground layers at Abadan Refinery was absorbed into clay soil.

  9. Energy and economic development [Brazil: A country profile on sustainable energy development

    International Nuclear Information System (INIS)

    Machado, G.; Schaeffer, R.

    2006-01-01

    When energy specialists discuss the relationships between energy use and economic development, the focus is usually on how energy supports economic growth, alleviates poverty and increases people's well-being. On rare occasions, though, the effect that a country's choices for promoting economic development have on energy production and use is a matter of concern. The purpose of this chapter is to evaluate the way Brazil's choices for promoting economic development over time have impacted primary and final energy use in the country. Economic growth has different levels of quality, which lead to different economic development paths. Some paths are more effective than others in creating wealth and in protecting and preserving natural resources and the environment for future generations. Quality actually matters as much for economic development as for energy. This chapter is divided into four sections covering energy and economic development relationships, the evolution of final energy use in Brazil, strategies to enhance sustainable energy development in the country and a summary of main issues. In Section 5.1, energy and economic development relationships are discussed, setting the background for the analysis of the impacts on final energy use of some of Brazil's choices for promoting economic development. The section begins by focusing on the basics of energy and economic development relationships. It should be noted that most energy specialists usually discuss only the basics of energy and economic development (the 'energy in support of economic development' theme), but this approach alone is not enough to explain differences in countries' final energy use patterns, or to identify strategies to enhance sustainable energy development. In this sense, the main contribution of this section is to further illuminate the role of social and economic choices in determining the effectiveness of a given country's economic development and that country's primary and final

  10. Quantitative operando visualization of the energy band depth profile in solar cells.

    Science.gov (United States)

    Chen, Qi; Mao, Lin; Li, Yaowen; Kong, Tao; Wu, Na; Ma, Changqi; Bai, Sai; Jin, Yizheng; Wu, Dan; Lu, Wei; Wang, Bing; Chen, Liwei

    2015-07-13

    The energy band alignment in solar cell devices is critically important because it largely governs elementary photovoltaic processes, such as the generation, separation, transport, recombination and collection of charge carriers. Despite the expenditure of considerable effort, the measurement of energy band depth profiles across multiple layers has been extremely challenging, especially for operando devices. Here we present direct visualization of the surface potential depth profile over the cross-sections of operando organic photovoltaic devices using scanning Kelvin probe microscopy. The convolution effect due to finite tip size and cantilever beam crosstalk has previously prohibited quantitative interpretation of scanning Kelvin probe microscopy-measured surface potential depth profiles. We develop a bias voltage-compensation method to address this critical problem and obtain quantitatively accurate measurements of the open-circuit voltage, built-in potential and electrode potential difference.

  11. Country analysis briefs: 1994. Profiles of major world energy producers, consumers, and transport centers

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    Country Analysis Briefs: 1994 is a compilation of country profiles prepared by the Energy Markets and Contingency Information Division (EMCID) of the Office of Energy Markets and End Use. EMCID maintains Country Analysis Briefs (CABs) for specific countries or geographical areas that are important to world energy markets. As a general rule, CABs are prepared for all members of the Organization of Petroleum Exporting Countries (OPEC), major non-OPEC oil producers (i.e., the North Sea, Russia), major energy transit areas (i.e., Ukraine), and other areas of current interest to energy analysts and policy makers. As of January 1995, EMCID maintained over 40 CABs, updated on an annual schedule and subject to revision as events warrant. This report includes 25 CABs updated during 1994. All CABs contain a profile section, a map showing the country`s location, and a narrative section. The profile section includes outlines of the country`s economy, energy sector, and environment. The narrative provides further information and discussion of these topics. Some CABs also include a detailed map displaying locations of major oil and gas fields, pipelines, ports, etc. These maps were created as a result of special individual requests and so are not typically a standard feature of the CABs. They are presented here wherever available as a supplement to the information contained in the CABs.

  12. Decision 99-8 : Shell Canada Limited application to construct and operate an oil sands bitumen upgrader in the Fort Saskatchewan area : Shell Canada Products Limited application to amend refinery approval in the Fort Saskatchewan area

    International Nuclear Information System (INIS)

    1999-01-01

    The Alberta Energy and Utilities Board considered an application by Shell Canada Limited to construct and operate an oil sands bitumen upgrader on Shell's property adjoining the existing Scotford refinery in the County of Strathcona. The upgrader would process bitumen from Shell's proposed Muskeg River Mine, located 70 km north of Fort McMurray, and other feedstocks available in the area. The Board also considered an application for an amendment to the existing Scotford refinery approval, Industrial Development Permit 89-10, for the processing of 3.75 million cubic metres per year of sour conversion feedstock. Under a coordinated application process, Shell filed a joint Shell Scotford Upgrader application/Environmental Impact Assessment. Issues considered with respect to these applications were: technology selection, air/health, sulphur recovery, noise/traffic, and land use conflict. Shell stated that its Scotford refinery is the most energy efficient refinery in the Americas and that is has the highest liquid yield per unit volume of crude oil feedstock of any refinery in the world. The refinery's hydrocracking capacity would make it possible to use hydro-conversion technology for its upgrader which is environmentally advantageous. After examining all of the evidence pertaining to the applications, the Board found the projects to be in the public interest and is prepared to approve the Scotford Upgrader and Scotford Refinery modifications assuming that certain prescribed conditions are met

  13. Building America Top Innovations 2014 Profile: California Energy Standards Recognize the Importance of Filter Selection

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2014-11-01

    This 2014 Top Innovation profile describes Building America research on HVAC air filter sizing that prompted a change in the California “Title 24” Energy Code requiring filter manufacturers, HVAC designers, and HERS raters to make changes that will encourage the use of higher MERV filters without degrading HVAC performance.

  14. Profiling technological failure and disaster in the energy sector: A comparative analysis of historical energy accidents

    International Nuclear Information System (INIS)

    Sovacool, Benjamin K.; Kryman, Matthew; Laine, Emily

    2015-01-01

    This study assesses the risk of energy accidents using an original historical dataset over the period 1874-2014, and it evaluates that risk across 11 energy systems: biofuels, biomass, coal, geothermal, hydroelectricity, hydrogen, natural gas, nuclear power, oil, solar energy, and wind energy. Our study shows how these energy systems collectively involved almost 1,100 accidents resulting in more than 210,000 human fatalities and almost $350 billion in property damages. Across the entire sample, the mean amount of property damage was $319 million and 196 fatalities per accident, though when reflected as a median the numbers substantially improve to $3 million in damages per accident and 0 fatalities. We found that wind energy is the most frequent to incur an accident within our sample, accounting for almost one third of accidents. Accidents at hydroelectric dams were the most fatal, accounting for 85 percent of fatalities. Nuclear power accidents are by far the most expensive, accounting for 70 percent of damages. We then utilize this data to test six hypotheses, drawn from the energy studies literature, related to energy systems, energy policy and regulation, and technological learning. - Highlights: • 1085 energy accidents have resulted in 211,529 human fatalities and $344.4 billion in property damages. • Wind energy is the most frequent to incur an accident. • Hydroelectric dam accidents tend to be the most fatal. • Nuclear energy accidents tend to be the most expensive. • Coal, natural gas, and oil are the least likely to incur an accident, when normalized to energy output.

  15. Modeling and prediction of extraction profile for microwave-assisted extraction based on absorbed microwave energy.

    Science.gov (United States)

    Chan, Chung-Hung; Yusoff, Rozita; Ngoh, Gek-Cheng

    2013-09-01

    A modeling technique based on absorbed microwave energy was proposed to model microwave-assisted extraction (MAE) of antioxidant compounds from cocoa (Theobroma cacao L.) leaves. By adapting suitable extraction model at the basis of microwave energy absorbed during extraction, the model can be developed to predict extraction profile of MAE at various microwave irradiation power (100-600 W) and solvent loading (100-300 ml). Verification with experimental data confirmed that the prediction was accurate in capturing the extraction profile of MAE (R-square value greater than 0.87). Besides, the predicted yields from the model showed good agreement with the experimental results with less than 10% deviation observed. Furthermore, suitable extraction times to ensure high extraction yield at various MAE conditions can be estimated based on absorbed microwave energy. The estimation is feasible as more than 85% of active compounds can be extracted when compared with the conventional extraction technique. Copyright © 2013 Elsevier Ltd. All rights reserved.

  16. An online, energy-resolving beam profile detector for laser-driven proton beams

    Energy Technology Data Exchange (ETDEWEB)

    Metzkes, J.; Rehwald, M.; Obst, L.; Schramm, U. [Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Bautzner Landstr. 400, 01328 Dresden (Germany); Technische Universität Dresden, 01062 Dresden (Germany); Zeil, K.; Kraft, S. D.; Sobiella, M.; Schlenvoigt, H.-P. [Helmholtz-Zentrum Dresden–Rossendorf (HZDR), Bautzner Landstr. 400, 01328 Dresden (Germany); Karsch, L. [OncoRay-National Center for Radiation Research in Oncology, Technische Universität Dresden, 01307 Dresden (Germany)

    2016-08-15

    In this paper, a scintillator-based online beam profile detector for the characterization of laser-driven proton beams is presented. Using a pixelated matrix with varying absorber thicknesses, the proton beam is spatially resolved in two dimensions and simultaneously energy-resolved. A thin plastic scintillator placed behind the absorber and read out by a CCD camera is used as the active detector material. The spatial detector resolution reaches down to ∼4 mm and the detector can resolve proton beam profiles for up to 9 proton threshold energies. With these detector design parameters, the spatial characteristics of the proton distribution and its cut-off energy can be analyzed online and on-shot under vacuum conditions. The paper discusses the detector design, its characterization and calibration at a conventional proton source, as well as the first detector application at a laser-driven proton source.

  17. Purification and detoxification of petroleum refinery wastewater by electrocoagulation process.

    Science.gov (United States)

    Gousmi, N; Sahmi, A; Li, H Z; Poncin, S; Djebbar, R; Bensadok, K

    2016-09-01

    The treatment of synthetic oily wastewater having the characteristics of a typical petroleum refinery wastewater (PRW) by electrocoagulation (EC) using iron and aluminum electrodes was conducted in an electrolytic reactor equipped with fluid recirculation. During the treatment, the emulsion stability was followed by the measurement of Zeta potential and particle sizes. Effects of some operating conditions such as electrodes material, current density and electrolysis time on removal efficiencies of turbidity, and chemical oxygen demand (COD) were investigated in detail. The PRW purification by the EC process was found to be the most effective using aluminum as the anode and cathode, current density of 60 A/m(2) and 30 min of electrolysis time. Under these conditions, the process efficiencies were 83.52% and 99.94%, respectively, for COD and turbidity removals which correspond to final values of 96 mg O2/L and 0.5 NTU. A moderate energy consumption (0.341 kWh) was needed to treat 1 m(3) of PRW. Besides, the ecotoxicity test proved that toxic substances presented in the PRW, and those inhibiting the germination growth of whet, were eliminated by the EC technique.

  18. Catalytic hydrotreatment of refinery waste: Demonstration project

    Energy Technology Data Exchange (ETDEWEB)

    1989-01-01

    The object of this project and report is to produce liquid hydrocarbons by the catalytic hydroprocessing of solid refinery wastes (hard pitches) in order to improve the profitability of deep conversion processes and reduce the excess production of heavy fuels. The project was mostly carried out on the ASVAHL demonstration platform site, at Solaize, and hard pitches were produced primarily by deasphalting of atmospheric or vacuum distillation residues. The project includes two experimental phases and an economic evaluation study phase. In Phase 1, two granular catalysts were used to transform pitch into standard low sulfur fuel oil: a continuously moving bed, with demetallation and conversion catalyst; a fixed bed, with hydrorefining catalyst. In Phase 2 of the project, it was proven that a hydrotreatment process using a finely dispersed catalyst in the feedstock, can, under realistic operating conditions, transform with good yields hard pitch into distillates that can be refined through standard methods. In Phase 3 of the project, it was shown that the economics of such processes are tightly linked to the price differential between white'' and black'' oil products, which is expected to increase in the future. Furthermore, the evolution of environmental constraints will impel the use of such methods, thus avoiding the coproduction of polluting solid residues. 11 figs., 1 tab.

  19. Development of chemical profiles for U.S. Department of Energy low-level mixed wastes

    International Nuclear Information System (INIS)

    Wang, Y.Y.; Wilkins, B.D.; Meshkov, N.K.; Dolak, D.A.

    1995-01-01

    Chemical and radiological profiles of waste streams from US Department of Energy (DOE) low-level mixed wastes (LLMWs) have been developed by Argonne National Laboratory (ANL) to provide technical support information for evaluating waste management alternatives in the Office of Environmental Management Programmatic Environmental Impact Statement (EM PEIS). The chemical profiles were developed for LLMW generated from both Waste Management (WM) operations and from Environmental Restoration (ER) activities at DOE facilities. Information summarized in the 1994 DOE Mixed Waste Inventory Report (MWIR-2), the Pacific Northwest Laboratory (PNL) Automated Remedial Assessment Methodology (ARAM), and associated PNL supporting data on ER secondary waste streams that will be treated in WM treatment facilities were used as the sources for developing chemical profiles. The methodology for developing the LLMW chemical profiles is discussed, and the chemical profiles developed from data for contact-handled (CH) non-alpha LLMW are presented in this paper. The hazardous chemical composition of remote-handled (RH) LLMW and alpha LLMW follow the chemical profiles developed for CH non-alpha LLMW

  20. World Energy Data System (WENDS). Volume VII. Nuclear facility profiles, AG--CH. [Brief tabulated information

    Energy Technology Data Exchange (ETDEWEB)

    1979-06-01

    In this compendium each profile of a nuclear facility is a capsule summary of pertinent facts regarding that particular installation. The facilities described include the entire fuel cycle in the broadest sense, encompassing resource recovery through waste management. Power plants and all US facilities have been excluded. To facilitate comparison the profiles have been recorded in a standard format. Because of the breadth of the undertaking some data fields do not apply to the establishment under discussion and accordingly are blank. The set of nuclear facility profiles occupies four volumes; the profiles are ordered by country name, and then by facility code. Each nuclear facility profile volume contains two complete indexes to the information. The first index aggregates the facilities alphabetically by country. It is further organized by category of facility, and then by the four-character facility code. It provides a quick summary of the nuclear energy capability or interest in each country and also an identifier, the facility code, which can be used to access the information contained in the profile.

  1. World Energy Data System (WENDS). Volume VIII. Nuclear facility profiles, CO--HU. [Brief tabulated information

    Energy Technology Data Exchange (ETDEWEB)

    1979-06-01

    In this compendium each profile of a nuclear facility is a capsule summary of pertinent facts regarding that particular installation. The facilities described include the entire fuel cycle in the broadest sense, encompassing resource recovery through waste management. Power plants and all US facilities have been excluded. To facilitate comparison the profiles have been recorded in a standard format. Because of the breadth of the undertaking some data fields do not apply to the establishment under discussion and accordingly are blank. The set of nuclear facility profiles occupies four volumes; the profiles are ordered by country name, and then by facility code. Each nuclear facility profile volume contains two complete indexes to the information. The first index aggregates the facilities alphabetically by country. It is further organized by category of facility, and then by the four-character facility code. It provides a quick summary of the nuclear energy capability or interest in each country and also an identifier, the facility code, which can be used to access the information contained in the profile.

  2. World Energy Data System (WENDS). Volume IX. Nuclear facility profiles, IN--PL. [Brief tabulated information

    Energy Technology Data Exchange (ETDEWEB)

    1979-06-01

    In this compendium each profile of a nuclear facility is a capsule summary of pertinent facts regarding that particular installation. The facilities described include the entire fuel cycle in the broadest sense, encompassing resource recovery through waste management. Power plants and all US facilities have been excluded. To facilitate comparison the profiles have been recorded in a standard format. Because of the breadth of the undertaking some data fields do not apply to the establishment under discussion and accordingly are blank. The set of nuclear facility profiles occupies four volumes; the profiles are ordered by country name, and then by facility code. Each nuclear facility profile volume contains two complete indexes to the information. The first index aggregates the facilities alphabetically by country. It is further organized by category of facility, and then by the four-character facility code. It provides a quick summary of the nuclear energy capability or interest in each country and also an identifier, the facility code, which can be used to access the information contained in the profile.

  3. World Energy Data System (WENDS). Volume VIII. Nuclear facility profiles, CO--HU

    International Nuclear Information System (INIS)

    1979-06-01

    In this compendium each profile of a nuclear facility is a capsule summary of pertinent facts regarding that particular installation. The facilities described include the entire fuel cycle in the broadest sense, encompassing resource recovery through waste management. Power plants and all US facilities have been excluded. To facilitate comparison the profiles have been recorded in a standard format. Because of the breadth of the undertaking some data fields do not apply to the establishment under discussion and accordingly are blank. The set of nuclear facility profiles occupies four volumes; the profiles are ordered by country name, and then by facility code. Each nuclear facility profile volume contains two complete indexes to the information. The first index aggregates the facilities alphabetically by country. It is further organized by category of facility, and then by the four-character facility code. It provides a quick summary of the nuclear energy capability or interest in each country and also an identifier, the facility code, which can be used to access the information contained in the profile

  4. World Energy Data System (WENDS). Volume IX. Nuclear facility profiles, IN--PL

    International Nuclear Information System (INIS)

    1979-06-01

    In this compendium each profile of a nuclear facility is a capsule summary of pertinent facts regarding that particular installation. The facilities described include the entire fuel cycle in the broadest sense, encompassing resource recovery through waste management. Power plants and all US facilities have been excluded. To facilitate comparison the profiles have been recorded in a standard format. Because of the breadth of the undertaking some data fields do not apply to the establishment under discussion and accordingly are blank. The set of nuclear facility profiles occupies four volumes; the profiles are ordered by country name, and then by facility code. Each nuclear facility profile volume contains two complete indexes to the information. The first index aggregates the facilities alphabetically by country. It is further organized by category of facility, and then by the four-character facility code. It provides a quick summary of the nuclear energy capability or interest in each country and also an identifier, the facility code, which can be used to access the information contained in the profile

  5. World Energy Data System (WENDS). Volume VII. Nuclear facility profiles, AG--CH

    International Nuclear Information System (INIS)

    1979-06-01

    In this compendium each profile of a nuclear facility is a capsule summary of pertinent facts regarding that particular installation. The facilities described include the entire fuel cycle in the broadest sense, encompassing resource recovery through waste management. Power plants and all US facilities have been excluded. To facilitate comparison the profiles have been recorded in a standard format. Because of the breadth of the undertaking some data fields do not apply to the establishment under discussion and accordingly are blank. The set of nuclear facility profiles occupies four volumes; the profiles are ordered by country name, and then by facility code. Each nuclear facility profile volume contains two complete indexes to the information. The first index aggregates the facilities alphabetically by country. It is further organized by category of facility, and then by the four-character facility code. It provides a quick summary of the nuclear energy capability or interest in each country and also an identifier, the facility code, which can be used to access the information contained in the profile

  6. World Energy Data System (WENDS). Volume X. Nuclear facility profiles, PO--ZA

    International Nuclear Information System (INIS)

    1979-06-01

    In this compendium each profile of a nuclear facility is a capsule summary of pertinent facts regarding that particular installation. The facilities described include the entire fuel cycle in the broadest sense, encompassing resource recovery through waste management. Power plants and all US facilities have been excluded. To facilitate comparison the profiles have been recorded in a standard format. Because of the breadth of the undertaking some data fields do not apply to the establishment under discussion and accordingly are blank. The set of nuclear facility profiles occupies four volumes; the profiles are ordered by country name, and then by facility code. Each nuclear facility profile volume contains two complete indexes to the information. The first index aggregates the facilities alphabetically by country. It is further organized by category of facility, and then by the four-character facility code. It provides a quick summary of the nuclear energy capability or interest in each country and also an identifier, the facility code, which can be used to access the information contained in the profile

  7. World Energy Data System (WENDS). Volume X. Nuclear facility profiles, PO--ZA. [Brief tabulated information

    Energy Technology Data Exchange (ETDEWEB)

    1979-06-01

    In this compendium each profile of a nuclear facility is a capsule summary of pertinent facts regarding that particular installation. The facilities described include the entire fuel cycle in the broadest sense, encompassing resource recovery through waste management. Power plants and all US facilities have been excluded. To facilitate comparison the profiles have been recorded in a standard format. Because of the breadth of the undertaking some data fields do not apply to the establishment under discussion and accordingly are blank. The set of nuclear facility profiles occupies four volumes; the profiles are ordered by country name, and then by facility code. Each nuclear facility profile volume contains two complete indexes to the information. The first index aggregates the facilities alphabetically by country. It is further organized by category of facility, and then by the four-character facility code. It provides a quick summary of the nuclear energy capability or interest in each country and also an identifier, the facility code, which can be used to access the information contained in the profile.

  8. Energy profiling of demersal fish: a case-study in wind farm artificial reefs.

    Science.gov (United States)

    De Troch, Marleen; Reubens, Jan T; Heirman, Elke; Degraer, Steven; Vincx, Magda

    2013-12-01

    The construction of wind farms introduces artificial hard substrates in sandy sediments. As Atlantic cod (Gadus morhua) and pouting (Trisopterus luscus) tend to aggregate in order to feed around these reefs, energy profiling and trophic markers were applied to study their feeding ecology in a wind farm in the Belgian part of the North Sea. The proximate composition (carbohydrates, proteins and lipids) differed significantly between liver and muscle tissue but not between fish species or between their potential prey species. Atlantic cod showed to consume more energy than pouting. The latter had a higher overall energy reserve and can theoretically survive twice as long on the available energy than cod. In autumn, both fish species could survive longer on their energy than in spring. Polyunsaturated fatty acids were found in high concentrations in fish liver. The prey species Jassa and Pisidia were both rich in EPA while Jassa had a higher DHA content than Pisidia. Energy profiling supported the statement that wind farm artificial reefs are suitable feeding ground for both fish species. Sufficient energy levels were recorded and there is no indication of competition.

  9. Energy Profile and Perspectives on Northeast Asian Energy Co-operation of North Korea

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    Energy policy of North Korea is basically based on the 'Principle of Self-reliance'. Throughout the active development of domestic energy sources, North Korea try to maximize the energy self-reliance as well as to minimize the outflow of currency for the import of energy. But, the 'Principle of Self-reliance' of energy sector brought about the excess dependency on coal and hydro, and eventually causes the contraction of oil and natural gas consumption. This kind of adverse reaction of the 'Principle of Self-reliance' is the major reason of overall weakness of national-wide economic system. It is not known actually what kinds of perspectives North Korea has on the Northeast Asian energy cooperation. But, it can be said that Northeast Asian energy cooperation can be the best chance for North Korea to solve current energy crisis and to transfer the economic system to capitalism for the recovery of national economy. 19 refs., 4 figs., 9 tabs.

  10. 2-D Low Energy Electron Beam Profile Measurement Based on Computer Tomography Algorithm with Multi-Wire Scanner

    CERN Document Server

    Yu, Nengjie; Li Qing Feng; Tang, Chuan-Xiang; Zheng, Shuxin

    2005-01-01

    A new method for low energy electron beam profile measurement is advanced, which presents a full 2-D beam profile distribution other than the traditional 2-D beam profile distribution given by 1-D vertical and horizontal beam profiles. The method is based on the CT (Computer Tomography) algorithm. Multi-sets of data about the 1-D beam profile projections are attained by rotating the multi-wire scanner. Then a 2-D beam profile is reconstructed from these projections with CT algorithm. The principle of this method is presented. The simulation and the experiment results are compared and analyzed in detail.

  11. Opportunities and challenges at the interface between petrochemistry and refinery. Preprints

    Energy Technology Data Exchange (ETDEWEB)

    Ernst, S.; Leitner, W.; Lercher, J.A.; Nees, F.; Perego, C.; Rupp, M.; Santacesaria. E. (eds.)

    2007-07-01

    Within the DGMK/SCI-Conference 'Opportunities and Challenges at the Interface between Petrochemistry and refinery' between 10th and 12th October, 2007, in Hamburg (Federal Republic of Germany) the following lectures were held: (a) Maximizing petrochemicals from refineries (B. Glover, T. Foley, S. Frey); (b) Opportunities and challenges at the interface between petrochemistry and refinery - the OMV view (J. Lichtscheidl); (c) Aspects of petrochemistry in a fuels refinery (J. Essler, J. Mielicke, T. Maier); (d) Enhanced propylene production in FCC by novel catalytic materials (C.P. Kelkar, D. Harris, M. Xu, J. Fu); (e) Retrofit of an MTBE-unit to ETBE (A. Rix, U. Peters); (f) Opportunities and challenges at the interface between petrochemistry and refinery - The BASF perspectives (H.-J. Blankertz); (g) Light olefins - challenges from new production routes? (H. Zimmermann); (h) Conversion of heavy aromatic hydrocarbons to valuable synthetic feed for steamcrackers (A. Cesana, L. Dalloro, F. Rivetti, R. Buzzoni, R. Bignazzi); (i) C{sub 4} olefin/paraffin separation over the metal organic framework material Cu{sub 3}BTC{sub 2} (S. Kunz, O. Tangermann, M. Hartmann); (j) Glycerol tertiary butyl ethers via etherification of glycerol with isobutene (A. Behr); (k) Biorefineries: From concepts to reality? (K. Wagemann); (l) Modern concepts in reactor and separation technologies (D. Agar); (m) Innovative reactive distillation process for the production of the MTBE substitute isooctane from isobutene (M. Chalakova, R. Kaur, H. Freund, S. Mahajani, K. Sundmacher); (n) Supported ionic liquid phase (SILP) systems - novel fixed bed reactor concepts for homogeneous catalysis (A. Riisager, R. Fehrmann, M. Haumann, M. Jakuttis, J. Joni, P. Wasserscheid); (o) Selective oxidations to industrial intermediates (S. Schunck); (p) Perspectives of industrial realization for propane oxidative dehydrogenation over chromium oxide catalysts (A.L. Lapidus, N.A. Gaidai, Yu. A. Agafonov, M

  12. Orbital momentum profiles and binding energy spectra for the complete valence shell of molecular fluorine

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Y.; Brion, C.E. [British Columbia Univ., Vancouver, BC (Canada). Dept. of Chemistry; Brunger, M.J.; Zhao, K.; Grisogono, A.M.; Braidwood, S.; Weigold, E. [Flinders Univ. of South Australia, Adelaide, SA (Australia). Electronic Structure of Materials Centre; Chakravorty, S.J.; Davidson, E.R. [Indiana Univ., Bloomington, IN (United States). Dept. of Chemistry; Sgamellotti, A. [Univ di Perugia (Italy). Dipartimento di Chimica; von Niessen, W. [Technische Univ. Braunschweig (Germany). Inst fuer Physikalische

    1996-01-01

    The first electronic structural study of the complete valence shell binding energy spectrum of molecular fluorine, encompassing both the outer and inner valence regions, is reported. These binding energy spectra as well as the individual orbital momentum profiles have been measured using an energy dispersive multichannel electron momentum spectrometer at a total energy of 1500 eV, with an energy resolution of 1.5 eV and a momentum resolution of 0.1 a.u. The measured binding energy spectra in the energy range of 14-60 eV are compared with the results of ADC(4) many-body Green`s function and also direct-Configuration Interaction (CI) and MRSD-CI calculations. The experimental orbital electron momentum profiles are compared with SCF theoretical profiles calculated using the target Hartree-Fock approximation with a range of basis sets and with Density Functional Theory predictions in the target Kohn-Sham approximation with non-local potentials. The truncated (aug-cc-pv5z) Dunning basis sets were used for the Density Functional Theory calculations which also include some treatment of correlation via the exchange and correlation potentials. Comparisons are also made with the full ion-neutral overlap amplitude calculated with MRSD-CI wave functions. Large, saturated basis sets (199-GTO) were employed for both the high level SCF near Hartree-Fock limit and MRSD-CI calculations to investigate the effects of electron correlation and relaxation. 66 refs., 9 tabs., 9 figs.

  13. A laser-wire beam-energy and beam-profile monitor at the BNL linac

    Energy Technology Data Exchange (ETDEWEB)

    Connolly, R.; Degen, C.; DeSanto, L.; Meng, W.; Michnoff, R.; Minty, M.; Nayak, S.

    2011-03-28

    In 2009 a beam-energy monitor was installed in the high energy beam transport (HEBT) line at the Brookhaven National Lab linac. This device measures the energies of electrons stripped from the 40mA H{sup -} beam by background gas. Electrons are stripped by the 2.0x10{sup -7}torr residual gas at a rate of {approx}1.5x10{sup -8}/cm. Since beam electrons have the same velocities as beam protons, the beam proton energy is deduced by multiplying the electron energy by m{sub p}/m{sub e}=1836. A 183.6MeV H{sup -} beam produces 100keV electrons. In 2010 we installed an optics plates containing a laser and scanning optics to add beam-profile measurement capability via photodetachment. Our 100mJ/pulse, Q-switched laser neutralizes 70% of the beam during its 10ns pulse. This paper describes the upgrades to the detector and gives profile and energy measurements.

  14. Energy profiles of the New England States and Eastern Canadian Provinces

    Energy Technology Data Exchange (ETDEWEB)

    Parsons, P.; Rodgers, B. [Newfoundland and Labrador Dept. of Mines and Energy, Energy Policy Analysis Div., St. John`s, NF (Canada)

    1998-06-01

    Recent developments affecting Atlantic Canada and New England`s energy sectors were discussed. Historically, both regions have relied on each other as an energy supplier or consumer. Fuels such as electricity and natural gas have been traded within the regions for decades. This trade is expected to continue because of the developments in the electricity restructuring in the United States and the planned increases in electricity capacity in Canada through new projects and expansions. Offshore oil and natural gas production in Eastern Canada is also expected to continue with planned natural gas pipeline additions in New England and Eastern Canada. This report presents regional comparisons as well as profiles of the energy economies of the eleven jurisdictions that make up New England and Eastern Canada. There are specific sections on electricity, energy forecasts and the environment. The report also includes basic demographic and economic performance indicators and updates and expands the profile of the region`s energy supply, consumption, trade and related trends. The report is largely statistical in nature and is intended to provide a quick snapshot of the region`s energy situation. 6 tabs., 23 figs.

  15. Planning and scheduling for petroleum refineries using mathematical programming

    Directory of Open Access Journals (Sweden)

    Joly M.

    2002-01-01

    Full Text Available The objective of this paper is the development and solution of nonlinear and mixed-integer (MIP optimization models for real-world planning and scheduling problems in petroleum refineries. Firstly, we present a nonlinear planning model that represents a general refinery topology and allows implementation of nonlinear process models as well as blending relations. The optimization model is able to define new operating points, thus increasing the production of the more valuable products and simultaneously satisfying all specification constraints. The second part addresses scheduling problems in oil refineries, which are formulated as MIP optimization models and rely on both continuous and discrete time representations. Three practical applications closely related to the current refinery scenario are presented. The first one addresses the problem of crude oil inventory management of a refinery that receives several types of crude oil delivered exclusively by a single oil pipeline. Subsequently, two optimization models intended to define the optimal production policy, inventory control and distribution are proposed and solved for the fuel oil and asphalt plant. Finally, the planning model of Moro et al. (1998 is extended in order to sequence decisions at the scheduling level in the liquefied petroleum gas (LPG area for maximization of the production of petrochemical-grade propane and product delivery.

  16. Profiling high performance dense linear algebra algorithms on multicore architectures for power and energy efficiency

    KAUST Repository

    Ltaief, Hatem

    2011-08-31

    This paper presents the power profile of two high performance dense linear algebra libraries i.e., LAPACK and PLASMA. The former is based on block algorithms that use the fork-join paradigm to achieve parallel performance. The latter uses fine-grained task parallelism that recasts the computation to operate on submatrices called tiles. In this way tile algorithms are formed. We show results from the power profiling of the most common routines, which permits us to clearly identify the different phases of the computations. This allows us to isolate the bottlenecks in terms of energy efficiency. Our results show that PLASMA surpasses LAPACK not only in terms of performance but also in terms of energy efficiency. © 2011 Springer-Verlag.

  17. Transformation of the Czech refinery and petrochemical

    International Nuclear Information System (INIS)

    Junek, V.

    1995-01-01

    The petrochemical and chemical industries in former Czechoslovakia in the period after World War II was built up with a purpose to create a complex whose individual subjects would be closely interlinked from the point of view of their production programmes. The separation of Slovakia as an independent state has disrupted some of these links. In spite of that the petrochemical and chemical industries are nowadays the most prosperous branches of economy of the Czech Republic. The governmental proposal for the reorganizing of the refinery and petrochemical complex elaborated in connection with the resolution of the Governmental Privatization Commission of November 6 1994 proposed the formation of a holding company Unipetrol in the way of merging Chemopetrol and Kaucuk with a new joint stock company Unipetrol established for this purpose by the National Property Fund. The updated proposal offers formation of the holding organization Unipetrol in a substantially simpler, from the point of view of time, organization and financing less demanding manner. This proposal is based on the following principles: respecting the approved privatization projects, the solution must not have influence on the rights and position of natural and juristic persons who became shareholders in accordance with the privatization projects already approved, the influence of the state on decisions of the holding and its daughter companies will be maintained with regard to the security of the state and supplying the strategically important subjects with fuels in situation of a crisis, the share of the business subjects in the shares of the holding will be such that it would enable them from the very beginning to participate effectively and not only formally in the decisions. 2 figs

  18. Algorithm Development for Multi-Energy SXR based Electron Temperature Profile Reconstruction

    Science.gov (United States)

    Clayton, D. J.; Tritz, K.; Finkenthal, M.; Kumar, D.; Stutman, D.

    2012-10-01

    New techniques utilizing computational tools such as neural networks and genetic algorithms are being developed to infer plasma electron temperature profiles on fast time scales (> 10 kHz) from multi-energy soft-x-ray (ME-SXR) diagnostics. Traditionally, a two-foil SXR technique, using the ratio of filtered continuum emission measured by two SXR detectors, has been employed on fusion devices as an indirect method of measuring electron temperature. However, these measurements can be susceptible to large errors due to uncertainties in time-evolving impurity density profiles, leading to unreliable temperature measurements. To correct this problem, measurements using ME-SXR diagnostics, which use three or more filtered SXR arrays to distinguish line and continuum emission from various impurities, in conjunction with constraints from spectroscopic diagnostics, can be used to account for unknown or time evolving impurity profiles [K. Tritz et al, Bull. Am. Phys. Soc. Vol. 56, No. 12 (2011), PP9.00067]. On NSTX, ME-SXR diagnostics can be used for fast (10-100 kHz) temperature profile measurements, using a Thomson scattering diagnostic (60 Hz) for periodic normalization. The use of more advanced algorithms, such as neural network processing, can decouple the reconstruction of the temperature profile from spectral modeling.

  19. Detection of impurities in fluid flowing in refinery pipeline or oil production operations using nuclear techniques

    International Nuclear Information System (INIS)

    Arnold, D.M.; Peelman, H.E.; Langford, O.M.; Paap, H.J.; Sopernaw, I.R.

    1977-01-01

    Fluid in a pipeline or container at a refinery or at any of various petroleum producing operations is bombarded with neutrons and high energy gamma rays resulting from capture of thermal neutrons are detected. The spectra of the detected gamma rays are then analyzed to determine the concentration of the element chlorine, which gives an indication of the presence and concentration of salt water in the fluid. The concentration of sulfur and the percentage gas in the fluid may be determined simultaneously with the concentration of chlorine. (Auth.)

  20. Test plan: the Czechowice Oil Refinery bioremediation demonstration of a process waste lagoon

    Energy Technology Data Exchange (ETDEWEB)

    Altman, D.J.; Lombard, K.H.; Hazen, T.C.

    1997-03-31

    The remediation strategies that will be applied at the Czechowice Oil Refinery waste lagoon in Czechowice, Poland are designed, managed, and implemented under the direction of the Westinghouse Savannah River Company (WSRC) for the United States Department of Energy (DOE). WSRC will be assisted in the demonstration by The Institute for Ecology of Industrial Areas (IETU). This collaboration between IETU and DOE will provide the basis for international technology transfer of new and innovative remediation technologies that can be applied in Poland and the Eastern European Region as well.

  1. The guava tree as bioindicator during the process of fuel replacement of an oil refinery.

    Science.gov (United States)

    Silva, Simone F; Meirelles, Sérgio T; Moraes, Regina M

    2013-05-01

    This study was performed to verify whether the exchange of the fuel used in the boilers of a crude oil refinery located in Cubatão (SE Brazil) would result in alterations on gas exchange, growth and leaf injuries in saplings of Psidium guajava 'Paluma'. The purpose of the refinery was to reduce the SO2 emission, but using natural gas as fuel could increase the concentrations of O3 precursors in the atmosphere. Thus a biomonitoring was performed with a native species sensitive to O3. The plants were exposed in five areas (CM1, CM5, CEPEMA, Centro, and RP) at different distances to the refinery, both before and after the fuel exchange. We performed six exposures under environmental conditions, with length of ca. 90 days each. With the utilization of natural gas, the saplings presented reductions in carbon assimilation rate under saturating light conditions (Asat, μmolCO2m(-2)s(-1)) and the stomatal conductance (gs, molH2Om(-2)s(-1)), and increase in height, number of leaves, and dry mass of leaves and shoots. There were also reductions in root dry mass and in the root/shoot ratio. The saplings also presented O3-induced leaf injuries. The responses of P. guajava 'Paluma' were altered after the fuel exchange as a result of a new combination of pollutants in the atmosphere. The fuel exchange has not resulted in environmental benefit to the surrounding forest; it has only altered the contamination profile of the region. Copyright © 2013 Elsevier Inc. All rights reserved.

  2. Biostimulation of indigenous microbial community for bioremediation of petroleum refinery sludge.

    Directory of Open Access Journals (Sweden)

    Jayeeta Sarkar

    2016-09-01

    Full Text Available Nutrient deficiency severely impairs the catabolic activity of indigenous microorganisms in hydrocarbon rich environments (HREs and limits the rate of intrinsic bioremediation. The present study aimed to characterize the microbial community in refinery waste and evaluate the scope for biostimulation based in situ bioremediation. Samples recovered from the wastewater lagoon of Guwahati refinery revealed a hydrocarbon enriched high total petroleum hydrocarbon (TPH, oxygen-, moisture-limited, reducing environment. Intrinsic biodegradation ability of the indigenous microorganisms was enhanced significantly (>80% reduction in TPH by 90 days with nitrate amendment. Preferred utilization of both higher- (>C30 and middle- chain (C20-30 length hydrocarbons were evident from GC-MS analysis. Denaturing gradient gel electrophoresis (DGGE and community level physiological profiling (CLPP analyses indicated distinct shift in community’s composition and metabolic abilities following nitrogen (N amendment. High throughput deep sequencing of 16S rRNA gene showed that the native community was mainly composed of hydrocarbon degrading, syntrophic, methanogenic, nitrate/iron/sulfur reducing facultative anaerobic bacteria and archaebacteria, affiliated to γ- and δ-Proteobacteria and Euryarchaeota respectively. Genes for aerobic and anaerobic alkane metabolism (alkB and bssA, methanogenesis (mcrA, denitrification (nirS and narG and N2 fixation (nifH were detected. Concomitant to hydrocarbon degradation, lowering of dissolve O2 and increase in oxidation-reduction potential (ORP marked with an enrichment of N2 fixing, nitrate reducing aerobic/facultative anaerobic members e.g., Azovibrio, Pseudoxanthomonas and Commamonadaceae members was evident in N amended microcosm. This study highlighted that indigenous community of refinery sludge was intrinsically diverse, yet appreciable rate of in situ bioremediation could be achieved by supplying adequate N sources.

  3. Biostimulation of Indigenous Microbial Community for Bioremediation of Petroleum Refinery Sludge

    Science.gov (United States)

    Sarkar, Jayeeta; Kazy, Sufia K.; Gupta, Abhishek; Dutta, Avishek; Mohapatra, Balaram; Roy, Ajoy; Bera, Paramita; Mitra, Adinpunya; Sar, Pinaki

    2016-01-01

    Nutrient deficiency severely impairs the catabolic activity of indigenous microorganisms in hydrocarbon rich environments (HREs) and limits the rate of intrinsic bioremediation. The present study aimed to characterize the microbial community in refinery waste and evaluate the scope for biostimulation based in situ bioremediation. Samples recovered from the wastewater lagoon of Guwahati refinery revealed a hydrocarbon enriched [high total petroleum hydrocarbon (TPH)], oxygen-, moisture-limited, reducing environment. Intrinsic biodegradation ability of the indigenous microorganisms was enhanced significantly (>80% reduction in TPH by 90 days) with nitrate amendment. Preferred utilization of both higher- (>C30) and middle- chain (C20-30) length hydrocarbons were evident from GC-MS analysis. Denaturing gradient gel electrophoresis and community level physiological profiling analyses indicated distinct shift in community’s composition and metabolic abilities following nitrogen (N) amendment. High throughput deep sequencing of 16S rRNA gene showed that the native community was mainly composed of hydrocarbon degrading, syntrophic, methanogenic, nitrate/iron/sulfur reducing facultative anaerobic bacteria and archaebacteria, affiliated to γ- and δ-Proteobacteria and Euryarchaeota respectively. Genes for aerobic and anaerobic alkane metabolism (alkB and bssA), methanogenesis (mcrA), denitrification (nirS and narG) and N2 fixation (nifH) were detected. Concomitant to hydrocarbon degradation, lowering of dissolve O2 and increase in oxidation-reduction potential (ORP) marked with an enrichment of N2 fixing, nitrate reducing aerobic/facultative anaerobic members [e.g., Azovibrio, Pseudoxanthomonas and Comamonadaceae members] was evident in N amended microcosm. This study highlighted that indigenous community of refinery sludge was intrinsically diverse, yet appreciable rate of in situ bioremediation could be achieved by supplying adequate N sources. PMID:27708623

  4. Decentralized Energy Management with Profile Steering : Resource Allocation Problems in Energy Management

    NARCIS (Netherlands)

    van der Klauw, Thijs

    2017-01-01

    Our energy supply chain is changing rapidly, driven by a societal push towards clean and renewable resources. However, these resources are often uncontrollable (e.g., wind and sun) and are increasingly being exploited on smaller scales (e.g., rooftop photovoltaic). This poses a reliability challenge

  5. Enterprise Integration of Management and Automation in a Refinery

    Science.gov (United States)

    Wang, Chengen

    Traditionally, problems in a petroleum refinery were separately modeled and solved with respect to disciplines. The segregated implementations of various disciplinary technologies resulted in considerable barriers impeding the pursuit of global optimal performance. It is recognized that enterprise-wide integration of the managerial and automation systems is of fundamental significance for refineries to promptly respond to global market requirements. In this paper, the technical implementations are disciplinarily categorized into managerial and automatic systems. Then, typical managerial and automatic implementations in a refinery are depicted to give an insight perception of the heterogeneous data sources manipulated by these systems. Finally, an integration approach based on data reconciliation techniques is proposed to link up the heterogeneous data sources.

  6. Operational planning of refineries; Planejamento operacional de refinarias

    Energy Technology Data Exchange (ETDEWEB)

    Sinay, Maria Cristina Fogliatti de [Instituto Militar de Engenharia (IME), Rio de Janeiro, RJ (Brazil); Bueno, Catia [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

    2004-07-01

    The activities integration that compose the petroleum logistic chain makes more complex its planning which is normally done in a joined level, using operation research models in order to find optimized solutions. When this integrated planning is repassed to the companies and its constitutes parts (mainly refinery) uncertainness are generated about the solution that will be adopted in case of new restrictions appear. Then, the purpose of this work is propose a procedure that is capable to adequate and specifies optimized solutions presented by corporative model to refinery operations, using 'What-if' and deterministic simulation technique with optimization. To achieve this objective will be analysed typical activities in refineries and basic principles to their operational planning. (author)

  7. Fitting partially upgraded oils into pipelines and refinery markets

    International Nuclear Information System (INIS)

    Flaherty, G.

    2000-01-01

    The logistics of transporting partially upgraded crudes in feeder and trunk pipeline systems is discussed. Logistic alternatives are evaluated against economic drivers for partial upgrading, and the impact of crude transportation logistics on the quality of crude that reaches refinery gates is assessed. The potential advantages of partial upgrading in the field are reviewed (including reduction of diluent required to meet pipeline density and viscosity specifications, cost and availability of diluent, limitations in diluent transportation infrastructure, increased chemical stability, increased attractiveness to refineries, shortage of refinery coking capacity, higher market value). The pros and cons of various upgrading processes, and the implications of each for producers and refiners are explained. The advantages of moving to large common streams, as opposed to the concept of 'boutique' crudes, are stressed as the surest way for producers to realize the maximum value of partially upgraded crudes

  8. An energy balance and greenhouse gas profile for county Wexford, Ireland in 2006

    International Nuclear Information System (INIS)

    Curtin, Richard

    2011-01-01

    Highlights: → Residential sector emits 38% of total CO 2 emissions. → Transport and industry/commerce sectors emit 28% each. → Oil composes 91% of total primary energy requirement (TPER). → Methane accounts for 25% of total greenhouse gas emissions. → Agriculture accounts for 36% of total greenhouse gas emissions. -- Abstract: In this paper an energy balance and a greenhouse gas profile has been formulated for the county of Wexford, situated in the south east of Ireland. The energy balance aims to aggregate all energy consumption in the county for the year 2006 across the following sectors; residential, agriculture, commerce and industry, and transport. The results of the energy balance are compared with the previous energy balance of 2001 where it is found that the residential sector is the biggest emitter of CO 2 with 38% of total emissions with the transport and industry/commerce sectors sharing second place on 28%. Consumption of oil is seen to have increased significantly in nearly all sectors, accounting for over 70% of the total final energy consumed (TFC) while the total primary energy requirement (TPER) sees oil consumption accounting for 91% of all fuels consumed. To take into account the contribution of agriculture in total GHG emissions the gases CH 4 and N 2 O will be estimated from the agricultural and waste sectors. The results show that methane contributes 25% of total GHG emissions with agriculture being the primary contributor accounting for 36% of total emissions.

  9. Nondestructive strain depth profiling with high energy X-ray diffraction: System capabilities and limitations

    Science.gov (United States)

    Zhang, Zhan; Wendt, Scott; Cosentino, Nicholas; Bond, Leonard J.

    2018-04-01

    Limited by photon energy, and penetration capability, traditional X-ray diffraction (XRD) strain measurements are only capable of achieving a few microns depth due to the use of copper (Cu Kα1) or molybdenum (Mo Kα1) characteristic radiation. For deeper strain depth profiling, destructive methods are commonly necessary to access layers of interest by removing material. To investigate deeper depth profiles nondestructively, a laboratory bench-top high-energy X-ray diffraction (HEXRD) system was previously developed. This HEXRD method uses an industrial 320 kVp X-Ray tube and the Kα1 characteristic peak of tungsten, to produces a higher intensity X-ray beam which enables depth profiling measurement of lattice strain. An aluminum sample was investigated with deformation/load provided using a bending rig. It was shown that the HEXRD method is capable of strain depth profiling to 2.5 mm. The method was validated using an aluminum sample where both the HEXRD method and the traditional X-ray diffraction method gave data compared with that obtained using destructive etching layer removal, performed by a commercial provider. The results demonstrate comparable accuracy up to 0.8 mm depth. Nevertheless, higher attenuation capabilities in heavier metals limit the applications in other materials. Simulations predict that HEXRD works for steel and nickel in material up to 200 µm, but experiment results indicate that the HEXRD strain profile is not practical for steel and nickel material, and the measured diffraction signals are undetectable when compared to the noise.

  10. Fiscal 1999 report on basic research for promotion of joint implementation programs. Energy saving project for Jingling Petrochemical Corp. Nanjing Refinery; 1999 nendo Jingling sekiyu kako koji Nanjing seiyusho shoene project chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A survey is conducted for the above named plant under an energy saving project expected to link to the clean development mechanism (CDM) of COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change). Studies are conducted about the refurbishment of the existing power recovering facilities in the wake of a plan for enhancing FCC (fluid catalytic cracker) processing capability and about power recovery from unused exhaust gas from the RFCC (residual fluid catalytic cracker) second catalyst regeneration tower. A modification plan was drafted and rough designs were prepared therefor, and it was found that power recovery from RFCC would be technologically and economically unfeasible because of the high temperature and extremely small quantity of the recoverable gas. It was then concluded that the plan be abandoned. Thanks to the refurbishment of the existing power recovering facilities to go out of service under the new operating conditions after FCC facility modification and to the installation of a new exhaust gas processor for air pollution prevention, there will be 10.6MW to be recovered for a reduction in fuel for in-house power generation. The consequential reduction in energy consumption will result in a CO2 reduction of 70,000 tons/year. Though China has not yet ratified the COP3 protocol, it is hoped that it will consider emission tradings and participate in the project when designated as a CDM country. (NEDO)

  11. Ashland outlines $261 million in refinery unit construction

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This paper reports that Ashland Petroleum Co. has spelled out $261 million in projects completed, under way, or planned to produce cleaner fuel and further reduce emissions at two U.S. refineries. The company: Started up at $13 million pollution control system at its 213,400 b/cd Catlettsburg, Ky., plant. Started construction on six projects at its 67,100 b/cd St. Paul Park, Minn., refinery that will cost about $114 million and enable the plant to produce cleaner burning diesel fuel and further reduce emissions

  12. 40 CFR 80.1238 - How is a refinery's or importer's average benzene concentration determined?

    Science.gov (United States)

    2010-07-01

    ... concentration determined? (a) The average benzene concentration of gasoline produced at a refinery or imported... percent benzene). i = Individual batch of gasoline produced at the refinery or imported during the applicable averaging period. n = Total number of batches of gasoline produced at the refinery or imported...

  13. 40 CFR 80.596 - How is a refinery motor vehicle diesel fuel volume baseline calculated?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 16 2010-07-01 2010-07-01 false How is a refinery motor vehicle diesel... Requirements § 80.596 How is a refinery motor vehicle diesel fuel volume baseline calculated? (a) For purposes of this subpart, a refinery's motor vehicle diesel fuel volume baseline is calculated using the...

  14. 77 FR 56421 - Standards of Performance for Petroleum Refineries; Standards of Performance for Petroleum...

    Science.gov (United States)

    2012-09-12

    ... Parts 9 and 60 Standards of Performance for Petroleum Refineries; Standards of Performance for Petroleum...-9672-3] RIN 2060-AN72 Standards of Performance for Petroleum Refineries; Standards of Performance for Petroleum Refineries for Which Construction, Reconstruction, or Modification Commenced After May 14, 2007...

  15. Depth profiling: RBS versus energy-dispersive X-ray imaging using scanning transmission electron microscopy

    International Nuclear Information System (INIS)

    Markwitz, Andreas

    2000-01-01

    Rutherford backscattering spectrometry (RBS) is known to be one of the techniques ideal for analysis of thin films. Elemental concentrations of matrix components and impurities can be investigated as well as depth profiles of almost each element of the periodic table. Best of all, RBS has both a high sensitivity and a high depth resolution, and is a non-destructive analysis technique that does not require specific sample preparation. Solid-state samples are mounted without preparation inside a high-vacuum analysis chamber. However, depth-related interpretation of elemental depth profiles requires the material density of the specimen and stopping power values to be taken into consideration. In many cases, these parameters can be estimated with sufficient precision. However, the assumed density can be inaccurate for depth scales in the nanometer range. For example, in the case of Ge nanoclusters in 500 nm thick SiO 2 layers, uncertainty is related to the actual position of a very thin Ge nanocluster band. Energy-dispersive X-ray emission (EDX) spectroscopy, using a high-resolution scanning transmission electron microscope (STEM) can assist in removing this uncertainty. By preparing a thin section of the specimen, EDX can be used to identify the position of the Ge nanocluster band very precisely, by correlating the Ge profile with the depth profiles of silicon and oxygen. However, extraction of the concentration profiles from STEM-EDX spectra is in general not straightforward. Therefore, a combination of the two very different analysis techniques is often the best and only successful way to extract high-resolution concentration profiles

  16. Computer model for refinery operations with emphasis on jet fuel production. Volume 3: Detailed systems and programming documentation

    Science.gov (United States)

    Dunbar, D. N.; Tunnah, B. G.

    1978-01-01

    The FORTRAN computing program predicts flow streams and material, energy, and economic balances of a typical petroleum refinery, with particular emphasis on production of aviation turbine fuels of varying end point and hydrogen content specifications. The program has a provision for shale oil and coal oil in addition to petroleum crudes. A case study feature permits dependent cases to be run for parametric or optimization studies by input of only the variables which are changed from the base case.

  17. ASSESSMENT OF CO2 EMISSION MITIGATION FOR A BRAZILIAN OIL REFINERY

    Directory of Open Access Journals (Sweden)

    W. N. Chan

    Full Text Available Abstract Currently the oil refining sector is responsible for approximately 5% of the total Brazilian energy related CO2 emissions. Possibilities to reduce CO2 emissions and related costs at the largest Brazilian refinery have been estimated. The abatement costs related to energy saving options are negative, meaning that feasibility exists without specific income due to emission reductions. The assessment shows that short-term mitigation options, i.e., fuel substitution and energy efficiency measures, could reduce CO2 emissions by 6% of the total current refinery emissions. It is further shown that carbon capture and storage offers the greatest potential for more significant emission reductions in the longer term (up to 43%, but costs in the range of 64 to162 US$/t CO2, depending on the CO2 emission source (regenerators of FCC units or hydrogen production units and the CO2 capture technology considered (oxyfuel combustion or post-combustion. Effects of uncertainties in key parameters on abatement costs are also evaluated via sensitivity analysis.

  18. Preliminary case studies of economy and energy profiles for Ireland during 1979-1990. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Henry, E W

    1981-01-01

    How Irish 1985 Energy Demand Model (EDM) case study results have been optimized on the supply side, by means of the EFOM model and software, are described. The 1985 case study results are for low, likely, and high cases. The Low case represents a 1985 Irish economic profile for real GNP being 54% greater thand the GNP of 1974. The Likely case relates to 1985 real GNP being 70% greater than that of 1974, and the High to real GNP being 92% greater. The 1985 final energy results emerging from the case studies are tabulated, showing quantities of final energy required by each of the 13 sectors of the Irish EDM. In all three case studies, 5 of the 13 demand sectors take in aggregate more than 76% of the total energy; these five sectors, in decreasing size of demand, are: other household uses; other industries; private transport; cement; other services. The preparation for EFOM is described. The optimal final energy flows, with some comparisons with the non-optimal inital flows, are considered. The gross primary energy quantity and cost underlying the optimal final energy flows are examined in detail.

  19. Depth profiling by Raman spectroscopy of high-energy ion irradiated silicon carbide

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Xu; Zhang, Yanwen; Liu, Shiyi; Zhao, Ziqiang, E-mail: zqzhao@pku.edu.cn

    2014-01-15

    Single crystals of 6H–SiC were irradiated at room temperature with 20 MeV carbon ions at fluences of 1.5 × 10{sup 15} and 6.0 × 10{sup 15} cm{sup −2}. Raman measurements were performed to study irradiation induced damage and the in-depth damage profile of SiC. A clear change of damage from the surface down to the stopping region of carbon ions as simulated by SRIM is exhibited. The affected area as detected by Raman is in good agreement with SRIM predictions while a little shallower dpa profile is observed. The partial disorder defined in the present work as a function of depth is demonstrated. A shift of the position of the TO peak towards lower wavenumbers with in-depth damage and then to higher wavenumbers beyond the most damaged region indicates that tensile strain due to defects has a backward V-curve distribution. The damaged layer is subjected to a compressive in-plane stress associated with the out-of-plane strain and the magnitude of this stress also has a backward V-curve depth profile. The evolution of line width of the TO peak with depth clearly shows the density of defects reaches the higher level at the most damaged region. The Raman spectroscopy scanning technique is proved to be a powerful tool for profiling of crystal damage induced by high-energy ion implantation.

  20. Lateral energy band profile modulation in tunnel field effect transistors based on gate structure engineering

    Directory of Open Access Journals (Sweden)

    Ning Cui

    2012-06-01

    Full Text Available Choosing novel materials and structures is important for enhancing the on-state current in tunnel field-effect transistors (TFETs. In this paper, we reveal that the on-state performance of TFETs is mainly determined by the energy band profile of the channel. According to this interpretation, we present a new concept of energy band profile modulation (BPM achieved with gate structure engineering. It is believed that this approach can be used to suppress the ambipolar effect. Based on this method, a Si TFET device with a symmetrical tri-material-gate (TMG structure is proposed. Two-dimensional numerical simulations demonstrated that the special band profile in this device can boost on-state performance, and it also suppresses the off-state current induced by the ambipolar effect. These unique advantages are maintained over a wide range of gate lengths and supply voltages. The BPM concept can serve as a guideline for improving the performance of nanoscale TFET devices.

  1. Increasing the complexity of a refinery: a analysis of the economic impacts of the introduction of new process in refineries; O aumento da complexidade de uma refinaria: uma analise dos impactos economicos da introducao de novos processos em refinarias

    Energy Technology Data Exchange (ETDEWEB)

    Fontes, Cristiane M; Seidl, Peter R [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Escola de Quimica

    2008-07-01

    The importance of the refining segment in the oil productive chain turns decision making on production and investment to be made at refineries dependent upon general context of the oil industry. Several technical and economic factors limit the possibilities to be foreseen by the managers. The ultimate goal of a refinery is to meet market demand in a region. Moreover, the type of processed oil and refining techniques will shape the profile of the production of derivatives. In a segment dynamic and full of uncertainties, such as refining, where the type of oil supplied to processing, specifications of products, and their demands, changes in the course of time, how to keep refining margins acceptable? This paper presents the relationship between the characteristics and the use of different kinds of oil, the characteristics of the national market of derivatives, and some characteristics of the refining processes considered in the study. The possible economic impacts that the introduction of different processes can bring to a refinery are analysed and alternatives for expansion are evaluated. To achieve these goals, a methodology for analysis considering the yield of Marlin oil refining for different schemes has been developed. (author)

  2. Reciprocal space mapping by spot profile analyzing low energy electron diffraction

    International Nuclear Information System (INIS)

    Meyer zu Heringdorf, Frank-J.; Horn-von Hoegen, Michael

    2005-01-01

    We present an experimental approach for the recording of two-dimensional reciprocal space maps using spot profile analyzing low energy electron diffraction (SPA-LEED). A specialized alignment procedure eliminates the shifting of LEED patterns on the screen which is commonly observed upon variation of the electron energy. After the alignment, a set of one-dimensional sections through the diffraction pattern is recorded at different energies. A freely available software tool is used to assemble the sections into a reciprocal space map. The necessary modifications of the Burr-Brown computer interface of the two Leybold and Omicron type SPA-LEED instruments are discussed and step-by-step instructions are given to adapt the SPA 4.1d software to the changed hardware. Au induced faceting of 4 deg. vicinal Si(001) is used as an example to demonstrate the technique

  3. Biorefineries: Relocating Biomass Refineries to the Rural Area

    Directory of Open Access Journals (Sweden)

    Franka Papendiek

    2012-07-01

    Full Text Available The field for application of biomass is rising. The demand for food and feeding stuff rises while at the same time energy, chemicals and other materials also need to be produced from biomass because of decreasing fossil resources. However, the biorefinery ideas and concepts can help to use the limited renewable raw materials more efficiently than today. With biorefineries, valuable products, such as platform chemicals, can be produced from agricultural feedstock, which can subsequently be further processed into a variety of substances by the chemical industry. Due to the role they play as producers of biomass, rural areas will grow in importance in the decades to come. Parts of the biorefinery process can be relocated to the rural areas to bring a high added value to these regions. By refining biomass at the place of production, new economic opportunities may arise for agriculturists, and the industry gets high-grade pre-products. Additionally, an on-farm refining can increase the quality of the products because of the instant processing. To reduce competition with the food production and to find new possibilities of utilisation for these habitats, the focus for new agricultural biomass should be on grasslands. But also croplands can provide more renewable raw materials without endangering a sustainable agriculture, e.g. by implementing legumes in the crop rotation. To decide if a region can provide adequate amounts of raw material for a biorefinery, new raw material assessment procedures have to be developed. In doing so, involvement of farmers is inevitable to generate a reliable study of the biomass refinery potentials.

  4. Theoretical ion implantation profiles for low energy protons under channeling conditions

    International Nuclear Information System (INIS)

    Nobel, J.A.; Sabin, J.R.; Trickey, S.B.

    1994-01-01

    The authors present early results from the CHANNEL code, which simulates the passage of ionized projectiles through bulk solids. CHANNEL solves the classical equations of motion for the projectile using a force obtained from the gradient of the quantum mechanically derived coulombic potential of the solid (determined via a full potential augmented plane wave (FLAPW) calculation on the bulk) and a quantum mechanical energy dissipation term, the stopping power, as determined from the method of Echenique, Neiminen, and Ritchie. The code then generates the trajectory of the ionic projectile for a given incident position on the unit cell face and an initial velocity. The authors use CHANNEL to generate an ion (proton) implantation profile for the test case of simple cubic hydrogen with the projectile's initial velocity parallel to the (100) channel. Further preliminary results for ion implantation profiles of protons in diamond structure Si, with initial velocity along the (100) and (110) channels, are given

  5. Energy confinement in the T-10 tokamak and canonic profile models

    International Nuclear Information System (INIS)

    Dnestrovskii, Yu.N.; Pereverzev, G.V.

    1988-01-01

    A classification of experimental results on electron cyclotron resonance heating (ECRH) is that T-10 tokamak is presented. Analysis of the experiments is consistent with two energy balance models. The first is based on the idea of profile consistency of the plasma current and pressure. The on-axis and off-axis ECRH as well as the heat wave propagation in T-10 can be reasonably represented in this way. In addition, this model allows the L to H mode transition to be described as the bifurcation of the solutions of a set of non-linear equations. The second model is based on the idea of a thermal pinch produced by a toroidal electric field. The electron temperature profiles under ohmic heating as well as under ECRH can be described by this model. Furthermore, this approach explains the cause of the confinement degradation under non-ohmic plasma heating (L-mode). (Author)

  6. Carbon filament beam profile monitor for high energy proton-antiproton storage rings

    International Nuclear Information System (INIS)

    Evans, L.R.; Shafer, R.E.

    1979-01-01

    The measurement of the evolution of the transverse profile of the stored beams in high energy proton storage rings such as the p-anti p colliders at CERN and at FNAL is of considerable importance. In the present note, a simple monitor is discussed which will allow almost non-destructive measurement of the profile of each individual proton and antiproton bunch separately. It is based on the flying wire technique first used at CEA and more recently at the CPS. A fine carbon filament is passed quickly through the beam, acting as a target for secondary particle production. The flux of secondary particles is measured by two scintillator telescopes, one for protons and one for antiprotons, having an angular acceptance between 30 and 100 mrad. Measurements of secondary particle production performed at FNAL in this angular range show that a very respectable flux can be expected

  7. Occupational health experience with a contractor uranium refinery

    International Nuclear Information System (INIS)

    Heatherton, R.C.

    1975-01-01

    This paper presents information related to the occupational exposure of workers in uranium refinery operations at the Feed Materials Production Center since 1958. Included are: a brief history of the FMPC; a description of the operations and the principal sources of exposure; airborne uranium, urinary excretion, in vivo monitoring and tissue analysis data; and some observations regarding the exposure and health status of employees

  8. A strategic review of the petroleum refinery industry sector

    International Nuclear Information System (INIS)

    1999-10-01

    The report studies the environmental performance of the U.K. petroleum refinery industry sector with reference to world-wide best practice and describes the five most practical strategic options for emission reduction in the context of projected technology, cost, demand, capacity and legislation. (author)

  9. Assessment of the effect of effluent discharge from coffee refineries ...

    African Journals Online (AJOL)

    The ecohydrological quality of water resource of Ethiopia is declining at an alarming rate, resulting in severe environmental degradation. This study finds out the effects of effluent discharge from intensive coffee refineries on river water quality based on physicochemical parameters and benthos assemblages as biological ...

  10. Environmental impact of illegal refineries on the vegetation of the ...

    African Journals Online (AJOL)

    ... aesthetic scenery of the forest, regeneration of plant species and destruction of wildlife habitat, disruption of water cycle and loss of medicinal plant species. Youth empowerment, through vocational training and environmental education can ameliorate the situation. Keywords: Environmental degradation, Illegal Refineries, ...

  11. Market survey on products from the Tema Oil Refinery carried out as part of the feasibility study on the Tema Oil Refinery expansion project. Export trade information

    International Nuclear Information System (INIS)

    Anon.

    1991-10-01

    The Tema Oil Refinery (TOR), which was commissioned in 1963, is a simple hydroskimming plant which processes crude oil into LPG, gasoline, kerosene, gasoil, and fuel oil. It is the only petroleum refinery in Ghana. Over the years some of the equipment in the refinery has deteriorated or become obsolete necessitating major rehabilitation. A feasibility study is investigating the modernization and expansion of the refinery to meet projected market demands until the year 2005. The report presents the results of a market survey done on products from TOR

  12. Development of Technological Profiles for Transfer of Energy- and Resource Saving Technologies

    Directory of Open Access Journals (Sweden)

    Lysenko, V.S.

    2015-01-01

    Full Text Available The article deals with the methodological foundations for the development of technological profiles for «System of Transfer of Energy- and Resource Saving Technologies». It is determined that a compliance with the methodology and standards of the European network «Relay Centers» (Innovation Relay Centers — IRC network, since 2008 — EEN, the Russian Technology Transfer Network RTTN and Uk rainian Technology Transfer Network UTTN is the main pri nciple of the development process of technological requests and offers.

  13. Oil refinery dusts: morphological and size analysis by TEM.

    Science.gov (United States)

    Sielicki, Przemysław; Janik, Helena; Guzman, Agnieszka; Broniszewski, Mieczysław; Namieśnik, Jacek

    2011-03-01

    The objectives of this work were to develop a means of sampling atmospheric dusts on the premises of an oil refinery for electron microscopic study to carry out preliminary morphological analyses and to compare these dusts with those collected at sites beyond the refinery limits. Carbon and collodion membranes were used as a support for collection of dust particles straight on transmission electron microscopy (TEM) grids. Micrographs of the dust particles were taken at magnifications from ×4,000 to ×80,000 with a Tesla BS500 transmission electron microscope. Four parameters were defined on the basis of the micrographs: surface area, Feret diameter, circumference, and shape coefficient. The micrographs and literature data were used to classify the atmospheric dusts into six groups: particles with an irregular shape and rounded edges; particles with an irregular shape and sharp edges; soot and its aggregates; spherical particles; singly occurring, ultrafine dust particles; and particles not allocated to any of the previous five groups. The types of dusts found in all the samples were similar, although differences did exist between the various morphological parameters. Dust particles with the largest Feret diameter were present in sample 3 (mean, 0.739 μm)-these were collected near the refinery's effluent treatment plant. The particles with the smallest diameter were found in the sample that had been intended to be a reference sample for the remaining results (mean, 0.326 μm). The dust particles collected in the refinery had larger mean Feret diameters, even 100% larger, than those collected beyond it. Particles with diameters from 0.1 to 0.2 μm made up the most numerous group in all the samples collected in the refinery.

  14. Oil refinery dusts: morphological and size analysis by TEM

    Energy Technology Data Exchange (ETDEWEB)

    Sielicki, Przemyslaw; Janik, Helena; Guzman, Agnieszka [Gdansk University of Technology, Department of Polymer Technology, Chemical Faculty, Gdansk (Poland); Broniszewski, Mieczyslaw [Environmental Protection Office, Lotos Group, Gdansk (Poland); Namiesnik, Jacek [Gdansk University of Technology, Department of Analytical Chemistry, Chemical Faculty, Gdansk (Poland)

    2011-03-15

    The objectives of this work were to develop a means of sampling atmospheric dusts on the premises of an oil refinery for electron microscopic study to carry out preliminary morphological analyses and to compare these dusts with those collected at sites beyond the refinery limits. Carbon and collodion membranes were used as a support for collection of dust particles straight on transmission electron microscopy (TEM) grids. Micrographs of the dust particles were taken at magnifications from x 4,000 to x 80,000 with a Tesla BS500 transmission electron microscope. Four parameters were defined on the basis of the micrographs: surface area, Feret diameter, circumference, and shape coefficient. The micrographs and literature data were used to classify the atmospheric dusts into six groups: particles with an irregular shape and rounded edges; particles with an irregular shape and sharp edges; soot and its aggregates; spherical particles; singly occurring, ultrafine dust particles; and particles not allocated to any of the previous five groups. The types of dusts found in all the samples were similar, although differences did exist between the various morphological parameters. Dust particles with the largest Feret diameter were present in sample 3 (mean, 0.739 {mu}m) - these were collected near the refinery's effluent treatment plant. The particles with the smallest diameter were found in the sample that had been intended to be a reference sample for the remaining results (mean, 0.326 {mu}m). The dust particles collected in the refinery had larger mean Feret diameters, even 100% larger, than those collected beyond it. Particles with diameters from 0.1 to 0.2 {mu}m made up the most numerous group in all the samples collected in the refinery. (orig.)

  15. Numerical calculation of 'actual' radial profile of ion temperature from 'measured' energy spectra of charge-exchanged neutrals

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, Kazuo; Hiraki, Naoji; Toi, Kazuo; Itoh, Satoshi

    1984-10-01

    The energy spectra of charge-exchanged neutrals are observed in the TRIAM-1 tokamak by vertical scanning of the neutral energy analyzer. The ''apparent'' ion temperature obtained directly from the energy spectrum observed in the peripheral region is much higher than that predicted by neoclassical transport theory. The ''actual'' ion temperature profile is derived numerically from the energy spectra observed at various positions taking into account the wall-reflection effect of neutrals and the impermeability of the plasma. As a result, the ''actual'' ion temperature profile is found to agree well with that predicted by neoclassical transport theory.

  16. Numerical calculation of 'actual' radial profile of ion temperature from 'measured' energy spectra of charge-exchanged neutrals

    International Nuclear Information System (INIS)

    Nakamura, Kazuo; Hiraki, Naoji; Toi, Kazuo; Itoh, Satoshi

    1984-01-01

    The energy spectra of charge-exchanged neutrals are observed in the TRIAM-1 tokamak by vertical scanning of the neutral energy analyzer. The ''apparent'' ion temperature obtained directly from the energy spectrum observed in the peripheral region is much higher than that predicted by neoclassical transport theory. The ''actual'' ion temperature profile is derived numerically from the energy spectra observed at various positions taking into account the wall-reflection effect of neutrals and the impermeability of the plasma. As a result, the ''actual'' ion temperature profile is found to agree well with that predicted by neoclassical transport theory. (author)

  17. Simulation calculation for the energy deposition profile and the transmission fraction of intense pulsed electron beam at various incident angles

    International Nuclear Information System (INIS)

    Yang Hailiang; Qiu Aici; Zhang Jiasheng; Huang Jianjun; Sun Jianfeng

    2002-01-01

    The incident angles have a heavy effect on the intense pulsed electron beam energy deposition profile, energy deposition fraction and beam current transmission fraction in material. The author presents electron beam energy deposition profile and energy deposition fraction versus electron energy (0.5-2.0 MeV), at various incident angles for three aluminum targets of various thickness via theoretical calculation. The intense pulsed electron beam current transmission fractions versus electron energy (0.4-1.4 MeV) at various incident angles for three thickness of carbon targets were also theoretically calculated. The calculation results indicate that the deposition energy in unit mass of material surface layer increase with the rise of electron beam incident angle, and electron beam with low incident angle (closer to normal incident angle) penetrates deeper into the target material. The electron beams deposit more energy in unit mass of material surface layer at 60 degree-70 degree incident angle

  18. An integrated biohydrogen refinery: synergy of photofermentation, extractive fermentation and hydrothermal hydrolysis of food wastes.

    Science.gov (United States)

    Redwood, Mark D; Orozco, Rafael L; Majewski, Artur J; Macaskie, Lynne E

    2012-09-01

    An Integrated Biohydrogen Refinery (IBHR) and experimental net energy analysis are reported. The IBHR converts biomass to electricity using hydrothermal hydrolysis, extractive biohydrogen fermentation and photobiological hydrogen fermentation for electricity generation in a fuel cell. An extractive fermentation, developed previously, is applied to waste-derived substrates following hydrothermal pre-treatment, achieving 83-99% biowaste destruction. The selective separation of organic acids from waste-fed fermentations provided suitable substrate for photofermentative hydrogen production, which enhanced the gross energy generation up to 11-fold. Therefore, electrodialysis provides the key link in an IBHR for 'waste to energy'. The IBHR compares favourably to 'renewables' (photovoltaics, on-shore wind, crop-derived biofuels) and also emerging biotechnological options (microbial electrolysis) and anaerobic digestion. Copyright © 2012 Elsevier Ltd. All rights reserved.

  19. Profile of Cognitive Ability and Multiple Intelligence of Vocational Students in Application of Electric Energy Conservation

    Science.gov (United States)

    Kurniawan, A.; Rustaman, N. Y.; Kaniawati, I.; Hasanah, L.

    2017-09-01

    The purpose of this study is to obtain a profile picture of cognitive ability and multiple intelligence of students on physics learning activities in relation to the discourse of conservation of electrical energy. Research activities are conducted in the even semester of the 2015/2016 school year. The subjects of the study were the students of class XI (36 students) in one of the state vocational schools in Bandung consisting of one class chosen at random (cluster random sampling). Research data in the form of cognitive ability test results and multiple intelligences are analyzed descriptively and qualitatively. Research data is then analyzed and compared with predetermined success indicators. The results showed that the cognitive abilities profile of students in vocational schools in Bandung is still low. This can be seen from the average score of cognitive ability of students in remember (C1) of 57.75, understanding (C2) of 53.50, applying (C3) of 43.75, and analyzing (C4) of 37.75. The multiple intelligence profiles indicate frequency of linguistic intelligence number 9 students, musical intelligence 3 students, logical mathematical intelligence 13 students, spatial intelligence 7 students, kinesthetic intelligence 5 students, intrapersonal intelligence 7 students, interpersonal intelligence 6 students, and naturalistic intelligence 5 students.

  20. Gamma ray scanning as troubleshooting tool for unusual and large diameter refinery vacuum columns

    International Nuclear Information System (INIS)

    Sarkar, T.K.; Chawla, R.; Banik, S.; Chopra, S.J.; Singh, G.; Pant, H.J.; Sreeramakrishnan, P.; Dhar, D.C.; Pushpangathan, P.N.; Sharma, V.K.

    1997-01-01

    Gamma scanning of trayed and packed columns is widely used to obtain density profiles and identify on-line problems such as: damaged tray or packing, foaming, flooding, maldistribution, weeping and entrainment, etc. However, scanning of large diameter tray or packed columns requires expertise in handling high intensity gamma sources along with thorough understanding of distillation engineering. Engineers India Limited and the Bhabha Atomic Research Centre undertook scanning of two such large diameter (8.4 m and 7.4 m) trayed and packed refinery vacuum distillation columns and successfully diagnosed the problems and suggested remedial actions. Radiography testing of small diameter columns can be used to confirm gamma scanning results. One such example for ammonia separator column is given

  1. Profiling Space Heating Behavior in Chilean Social Housing: Towards Personalization of Energy Efficiency Measures

    Directory of Open Access Journals (Sweden)

    Victor Bunster

    2015-06-01

    Full Text Available Global increases in the demand for energy are imposing strong pressures over the environment while compromising the capacity of emerging economies to achieve sustainable development. In this context, implementation of effective strategies to reduce consumption in residential buildings has become a priority concern for policy makers as minor changes at the household scale can result in major energy savings. This study aims to contribute to ongoing research on energy consumer profiling by exploring the forecasting capabilities of discrete socio-economic factors that are accessible through social housing allocation systems. Accordingly, survey data gathered by the Chilean Ministry of Social Development was used identify key characteristics that may predict firewood usage for space heating purposes among potential beneficiaries of the Chilean social housing program. The analyzed data evidences strong correlations between general household characteristics and space heating behavior in certain climatic zones, suggesting that personalized delivery of energy efficiency measures can potentially increase the effectiveness of initiatives aimed towards the reduction of current patterns of consumption.

  2. Energy Response and Longitudinal Shower Profiles Measured in CMS HCAL and Comparison With Geant4

    CERN Document Server

    Baiatian, G; Emeliantchik, Igor; Massolov, V; Shumeiko, Nikolai; Stefanovich, R; Damgov, Jordan; Dimitrov, Lubomir; Genchev, Vladimir; Piperov, Stefan; Vankov, Ivan; Litov, Leander; Bencze, Gyorgy; Laszlo, Andras; Pal, Andras; Vesztergombi, Gyorgy; Zálán, Peter; Fenyvesi, Andras; Bawa, Harinder Singh; Beri, Suman Bala; Bhatnagar, Vipin; Kaur, Manjit; Kohli, Jatinder Mohan; Kumar, Arun; Singh, Jas Bir; Acharya, Bannaje Sripathi; Banerjee, Sunanda; Banerjee, Sudeshna; Chendvankar, Sanjay; Dugad, Shashikant; Kalmani, Suresh Devendrappa; Katta, S; Mazumdar, Kajari; Mondal, Naba Kumar; Nagaraj, P; Patil, Mandakini Ravindra; Reddy, L; Satyanarayana, B; Sharma, Seema; Sudhakar, Katta; Verma, Piyush; Hashemi, Majid; Mohammadi-Najafabadi, M; Paktinat, S; Golutvin, Igor; Kalagin, Vladimir; Kosarev, Ivan; Ladygin, Vladimir; Mescheryakov, G; Moissenz, P; Petrosian, A; Sergeyev, S; Smirnov, Vitaly; Vishnevskiy, Alexander; Volodko, Anton; Zarubin, Anatoli; Gavrilov, Vladimir; Gershtein, Yuri; Ilyina, N; Kaftanov, Vitali; Kisselevich, I; Kolossov, V; Krokhotin, Andrey; Kuleshov, Sergey; Litvintsev, Dmitri; Ulyanov, A; Safronov, Grigory; Semenov, Sergey; Stolin, Viatcheslav; Demianov, A; Gribushin, Andrey; Kodolova, Olga; Petrushanko, Sergey; Sarycheva, Ludmila; Teplov, V; Vardanyan, Irina; Yershov, A; Abramov, Victor; Goncharov, Petr; Kalinin, Alexey; Khmelnikov, Alexander; Korablev, Andrey; Korneev, Yury; Krinitsyn, Alexander; Kryshkin, V; Lukanin, Vladimir; Pikalov, Vladimir; Ryazanov, Anton; Talov, Vladimir; Turchanovich, L; Volkov, Alexey; Camporesi, Tiziano; De Visser, Theo; Vlassov, E; Aydin, Sezgin; Bakirci, Mustafa Numan; Cerci, Salim; Dumanoglu, Isa; Eskut, Eda; Kayis-Topaksu, A; Koylu, S; Kurt, Pelin; Onengüt, G; Ozkurt, Halil; Polatoz, A; Sogut, Kenan; Topakli, Huseyin; Vergili, Mehmet; Yetkin, Taylan; Cankocak, Kerem; Esendemir, Akif; Gamsizkan, Halil; Güler, M; Ozkan, Cigdem; Sekmen, Sezen; Serin-Zeyrek, M; Sever, Ramazan; Yazgan, Efe; Zeyrek, Mehmet; Deliomeroglu, Mehmet; Dindar, Kamile; Gülmez, Erhan; Isiksal, Engin; Kaya, Mithat; Ozkorucuklu, Suat; Levchuk, Leonid; Sorokin, Pavel; Senchishin, V; Hauptman, John M; Abdullin, Salavat; Elias, John E; Elvira, D; Freeman, Jim; Green, Dan; Los, Serguei; O'Dell, Vivian; Ronzhin, Anatoly; Suzuki, Ichiro; Vidal, Richard; Whitmore, Juliana; Arcidy, M; Hazen, Eric; Heering, Arjan Hendrix; Lawlor, C; Lazic, Dragoslav; Machado, Emanuel; Rohlf, James; Varela, F; Wu, Shouxiang; Baden, Drew; Bard, Robert; Eno, Sarah Catherine; Grassi, Tullio; Jarvis, Chad; Kellogg, Richard G; Kunori, Shuichi; Mans, Jeremy; Skuja, Andris; Podrasky, V; Sanzeni, Christopher; Winn, Dave; Akgun, Ugur; Ayan, S; Duru, Firdevs; Merlo, Jean-Pierre; Mestvirishvili, Alexi; Miller, Michael; Norbeck, Edwin; Olson, Jonathan; Onel, Yasar; Schmidt, Ianos; Akchurin, Nural; Carrell, Kenneth Wayne; Gumus, Kazim; Kim, Heejong; Spezziga, Mario; Thomas, Ray; Baarmand, Marc M; Mermerkaya, Hamit; Ralich, Robert; Vodopiyanov, Igor; Kramer, Laird; Linn, Stephan; Markowitz, Pete; Cushman, Priscilla; Ma, Yousi; Sherwood, Brian; Cremaldi, Lucien Marcus; Reidy, Jim; Sanders, David A; Karmgard, Daniel John; Ruchti, Randy; Fisher, Wade Cameron; Tully, Christopher; Bodek, Arie; De Barbaro, Pawel; Budd, Howard; Chung, Yeon Sei; Haelen, T; Hagopian, Sharon; Hagopian, Vasken; Johnson, Kurtis F; Barnes, Virgil E; Laasanen, Alvin T

    2007-01-01

    The response of the CMS combined electromagnetic and hadron calorimeter to beams of pions with momenta in the range 5-300 GeV/c has been measured in the H2 test beam at CERN. The raw response with the electromagnetic compartment calibrated to electrons and the hadron compartment calibrated to 300 GeV pions may be represented by sigma = (1.2) sqrt{E} oplus (0.095) E. The fraction of energy visible in the calorimeter ranges from 0.72 at 5 GeV to 0.95 at 300 GeV, indicating a substantial nonlinearity. The intrinsic electron to hadron ratios are fit as a function of energy and found to be in the range 1.3-2.7 for the electromagnetic compartment and 1.4-1.8 for the hadronic compartment. The fits are used to correct the non-linearity of the e pi response to 5% over the entire measured range resulting in a substantially improved resolution at low energy. Longitudinal shower profile have been measured in detail and compared to Geant4 models, LHEP-3.7 and QGSP-2.8. At energies below 30 GeV, the data, LHEP and QGSP are...

  3. Invention profiles and uneven growth in the field of emerging nano-energy

    International Nuclear Information System (INIS)

    Guan, Jiancheng; Liu, Na

    2015-01-01

    This paper aims to synthetically investigate invention profiles and uneven growth of technological knowledge in the emerging nano-energy field, based on patents data extracted from the Derwent Innovation Index (DII) database during the time period 1991–2012. The trend analysis shows that invention in this field has experienced enormous growth and also diversification over the past 22 years. The co-occurrence network of burst technology domains reveals that technology domains constantly burst, and innovative progress in nanotechnology has tremendously contributed to energy production, storage, conversion and harvesting and so on. Nano-energy patented inventions mainly come from a combinatorial process with a very limited role of developing brand-new technological capabilities. Reusing existing technological capabilities including recombination reuse, recombination creation and single reuse is the primary source of inventions. For the impacts of technology networks' embeddedness, we find that network tie strength suppresses the growth of technological knowledge domains, and network status and convergence both facilitate the growth of technological knowledge domains. We expect that this study will provide some enlightenment for inventing or creating new knowledge in emerging fields in complex technological environment. - Highlights: • We define and utilize a unique dataset of nano-energy patents. • We identify and map the burst technological knowledge domains. • Quantitative argument is provided to prove the combinatorial invention. • Impacts of network embeddedness on growth of technology domain are examined. • Network characteristics affect the growth of technology domain

  4. Treatment of Mineral Oil Refinery Wastewater in Microbial Fuel Cells Using Ionic Liquid Based Separators

    Directory of Open Access Journals (Sweden)

    Hasna Addi

    2018-03-01

    Full Text Available Microbial fuel cells (MFCs are an environmentally friendly technology that can recover electricity directly from several wastes at ambient temperatures. This work explores the use of mineral oil refinery wastewater as feedstock in single-chamber air-cathode MFC devices. A polymer inclusion membrane based on the ionic liquid methyltrioctylammonium chloride, [MTOA+][Cl−], at a concentration of 70% w/w, was used as separator, showing a good efficiency in power production and chemical oxygen demand (COD removal. The power and the chemical oxygen demand removal reached values of 45 mW/m3 and over 80%, respectively. The evolution of other parameters of the wastewater including nitrites, phosphates and sulphates were also studied. Kjeldahl nitrogen and sulphates were significantly reduced during MFC operation. The results show that mineral oil refinery wastewater can be used as feedstock in air breathing cathode-microbial fuel cells based on polymer ionic liquid inclusion membranes. This configuration could represent a good alternative for wastewater depuration while producing energy during the process.

  5. Hydroprocessing and premium II refinery: a new refining philosophy for an era of clean fuels

    Energy Technology Data Exchange (ETDEWEB)

    Delgaudio, Caio Veiga Penna; Pinotti, Rafael [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil)

    2012-07-01

    This paper discusses a brief history of Brazilian's emission and fuel specifications, since the appearance of PROCONVE until the late stages of the program for vehicles powered by gasoline and diesel. The development of the Brazilian refining is analyzed taking into account the emission and specification evolutions, and it can be perceived that the system's complexity increases while new constraints are imposed by the regulator. This aspect is even more apparent when the detailed scheme of the Premium II refinery and its main unit, the catalytic hydrocracker (HCC, which has not yet been part of PETROBRAS' refining park and will appear in three of the four new refineries of the company) is described. The new projects represent the culmination of the intensive use of energy and raw material for obtaining the products with the new specifications. There is a price for this development, both in investments and increased operating costs due to greater complexity of the system. To adapt to the era of clean fuels, refiners will present a series of challenges that will lead them to seek for more efficient processes and operational excellence (and ongoing efforts to reduce their emissions) in order to ensure positive refining margins. (author)

  6. Energy, cost, and emission end-use profiles of homes: An Ontario (Canada) case study

    International Nuclear Information System (INIS)

    Aydinalp Koksal, Merih; Rowlands, Ian H.; Parker, Paul

    2015-01-01

    Highlights: • Hourly electricity consumption data of seven end-uses from 25 homes are analyzed. • Hourly load, cost, and emission profiles of end-uses are developed and categorized. • Side-by-side analysis of energy, cost, and environmental effects is conducted. • Behaviour and outdoor temperature based end-uses are determined. • Share of each end-use in the total daily load, cost, and emission is determined. - Abstract: Providing information on the temporal distributions of residential electricity end-uses plays a major role in determining the potential savings in residential electricity demand, cost, and associated emissions. While the majority of the studies on disaggregated residential electricity end-use data provided hourly usage profiles of major appliances, only a few of them presented analysis on the effect of hourly electricity consumption of some specific end-uses on household costs and emissions. This study presents side-by-side analysis of energy, cost, and environment effects of hourly electricity consumption of the main electricity end-uses in a sample of homes in the Canadian province of Ontario. The data used in this study are drawn from a larger multi-stakeholder project in which electricity consumption of major end-uses at 25 homes in Milton, Ontario, was monitored in five-minute intervals for six-month to two-year periods. In addition to determining the hourly price of electricity during the monitoring period, the hourly carbon intensity is determined using fuel type hourly generation and the life cycle greenhouse gas intensities specifically determined for Ontario’s electricity fuel mix. The hourly load, cost, and emissions profiles are developed for the central air conditioner, furnace, clothes dryer, clothes washer, dishwasher, refrigerator, and stove and then grouped into eight day type categories. The side-by-side analysis of categorized load, cost, and emission profiles of the seven electricity end-uses provided information on

  7. Energy Intake, Profile, and Dietary Sources in the Spanish Population: Findings of the ANIBES Study

    Directory of Open Access Journals (Sweden)

    Emma Ruiz

    2015-06-01

    Full Text Available Energy intake, and the foods and beverages contributing to that, are considered key to understanding the high obesity prevalence worldwide. The relative contributions of energy intake and expenditure to the obesity epidemic, however, remain poorly defined in Spain. The purpose of this study was to contribute to updating data of dietary energy intake and its main sources from food and beverages, according to gender and age. These data were derived from the ANIBES (“Anthropometry, Intake, and Energy Balance in Spain” study, a cross-sectional study of a nationally representative sample of the Spanish population (from 9–75 years old. A three-day dietary record, collected by means of a tablet device, was used to obtain information about food and beverage consumption and leftovers. The final sample comprised 2009 individuals (1,013 men, 996 women. The observed mean dietary energy intake was 7.6 ± 2.11 MJ/day (8.2 ± 2.22 MJ/day for men and 6.9 ± 1.79 MJ/day for women. The highest intakes were observed among adolescents aged 13–17 years (8.4 MJ/day, followed by children 9–12 years (8.2 ± 1.80 MJ/day, adults aged 18–64 (7.6 ± 2.14 MJ/day and older adults aged 65–75 years (6.8 ± 1.88 MJ/day. Cereals or grains (27.4%, meats and derivatives (15.2%, oils and fats (12.3%, and milk and dairy products (11.8% contributed most to daily energy intake. Energy contributions from non-alcoholic beverages (3.9%, fish and shellfish (3.6%, sugars and sweets (3.3% and alcoholic beverages (2.6% were moderate to minor. Contributions to caloric profile were 16.8%E from proteins; 41.1%E from carbohydrates, including 1.4%E from fiber; 38.5%E from fats; and 1.9%E from alcohol intake. We can conclude that energy intake is decreasing in the Spanish population. A variety of food and beverage groups contribute to energy intake; however, it is necessary to reinforce efforts for better adherence to the traditional Mediterranean diet.

  8. Energy Intake, Profile, and Dietary Sources in the Spanish Population: Findings of the ANIBES Study.

    Science.gov (United States)

    Ruiz, Emma; Ávila, José Manuel; Valero, Teresa; del Pozo, Susana; Rodriguez, Paula; Aranceta-Bartrina, Javier; Gil, Ángel; González-Gross, Marcela; Ortega, Rosa M; Serra-Majem, Lluis; Varela-Moreiras, Gregorio

    2015-06-12

    Energy intake, and the foods and beverages contributing to that, are considered key to understanding the high obesity prevalence worldwide. The relative contributions of energy intake and expenditure to the obesity epidemic, however, remain poorly defined in Spain. The purpose of this study was to contribute to updating data of dietary energy intake and its main sources from food and beverages, according to gender and age. These data were derived from the ANIBES ("Anthropometry, Intake, and Energy Balance in Spain") study, a cross-sectional study of a nationally representative sample of the Spanish population (from 9-75 years old). A three-day dietary record, collected by means of a tablet device, was used to obtain information about food and beverage consumption and leftovers. The final sample comprised 2009 individuals (1,013 men, 996 women). The observed mean dietary energy intake was 7.6 ± 2.11 MJ/day (8.2 ± 2.22 MJ/day for men and 6.9 ± 1.79 MJ/day for women). The highest intakes were observed among adolescents aged 13-17 years (8.4 MJ/day), followed by children 9-12 years (8.2 ± 1.80 MJ/day), adults aged 18-64 (7.6 ± 2.14 MJ/day) and older adults aged 65-75 years (6.8 ± 1.88 MJ/day). Cereals or grains (27.4%), meats and derivatives (15.2%), oils and fats (12.3%), and milk and dairy products (11.8%) contributed most to daily energy intake. Energy contributions from non-alcoholic beverages (3.9%), fish and shellfish (3.6%), sugars and sweets (3.3%) and alcoholic beverages (2.6%) were moderate to minor. Contributions to caloric profile were 16.8%E from proteins; 41.1%E from carbohydrates, including 1.4%E from fiber; 38.5%E from fats; and 1.9%E from alcohol intake. We can conclude that energy intake is decreasing in the Spanish population. A variety of food and beverage groups contribute to energy intake; however, it is necessary to reinforce efforts for better adherence to the traditional Mediterranean diet.

  9. New Sustainable Model of Biorefineries: Biofactories and Challenges of Integrating Bio- and Solar Refineries.

    Science.gov (United States)

    Abate, Salvatore; Lanzafame, Paola; Perathoner, Siglinda; Centi, Gabriele

    2015-09-07

    The new scenario for sustainable (low-carbon) chemical and energy production drives the development of new biorefinery concepts (indicated as biofactories) with chemical production at the core, but flexible and small-scale production. An important element is also the integration of solar energy and CO2 use within biobased production. This concept paper, after shortly introducing the motivation and recent trends in this area, particularly at the industrial scale, and some of the possible models (olefin and intermediate/high-added-value chemicals production), discusses the opportunities and needs for research to address the challenge of integrating bio- and solar refineries. Aspects discussed regard the use of microalgae and CO2 valorization in biorefineries/biofactories by chemo- or biocatalysis, including possibilities for their synergetic cooperation and symbiosis, as well as integration within the agroenergy value chain. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Pemex to acquire interest in Shell Texas refinery

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This paper reports that Petroleos Mexicanos and Shell Oil Co. have signed a memorandum of understanding to form a joint refining venture involving Shell's 225,000 b/d Deer Park, Tex., refinery. Under the agreement, Mexico's state owned oil company is to purchase a 50% interest in the refinery, and Shell is to sell Pemex unleaded gasoline on a long term basis. Under the venture, Shell and Pemex plan to add undisclosed conversion and upgrading units tailored to process heavy Mexican crude. The revamp will allow Pemex to place more than 100,000 b/d of Mayan heavy crude on the U.S. market. Mayan accounts for 70% of Mexico's crude oil exports. In turn, Shell will sell Pemex as much as 45,000 b/d of unleaded gasoline to help meet Mexico's rapidly growing demand

  11. Refinery production planning and scheduling: the refining core business

    Directory of Open Access Journals (Sweden)

    M. Joly

    2012-06-01

    Full Text Available Intelligent production planning and scheduling are of paramount importance to ensure refinery profitability, logistic reliability and safety at the local and corporate levels. In Brazil, such activities play a particularly critical role, since the Brazilian downstream model is moving towards a demand-driven model rather than a supply-driven one. Moreover, new and specialized non-linear constraints are continuously being incorporated into these large-scale problems: increases in oil prices implying the need for processing poor quality crudes, increasing demand and new demand patterns for petroleum products, new stringent environmental regulations related to clean fuels and start-up of new production technologies embedded into more complex refining schemes. This paper aims at clarifying the central role of refinery planning and scheduling activities in the Petrobras refining business. Major past and present results are outlined and corporate long-term strategies to deal with present and future challenges are presented.

  12. Application of PIMS Software in Monthly Planning of Refinery Production

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    This article describes the application of the PIMS software in formulating monthly refining production plan. Application of the PIMS software can help to solve a series of problems related with monthly plan of refining production such as optimized selection of crude and feedstocks, optimized selection of production scale and processing scheme, identification of bottlenecks and their mitigation,optimized selection of turnaround time and optimized selection of operating regime, which have increased the economic benefits of refining enterprises. With the further development and improvement of models the PIMS software will play an increasingly important role in formulating monthly plans of refining operations and production management at refineries. This article also explores the problems existing in refinery monthly planning, and has made recommendations on developing and improving models and reporting system, enhancement of basic data acquisition, model maintenance personnel and staff training.

  13. Metabolic profile in growing buffalo heifers fed diet with different energy content

    Directory of Open Access Journals (Sweden)

    B. Gasparrini

    2010-02-01

    Full Text Available Aim of this study was to verify the relation among the mediators and indicators of nutritional status like insulin, glucagon, urea, cholesterol, triglycerides and total proteins in growing buffalo heifers, fed diets with different energy density. 12 Murrah heifers were randomly allocated into two dietary treatments (High, Group H; Low, Group L that differed in energetic levels (Group H: 5.8 UFL/d; Group L: 3.6 UFL/d. Every 30 days, for a total of five times, blood samples were collected at 08.00 h, before feeding, from the jugular vein in vacutainer tubes and analysed to determine metabolic profile. Data on haematic constants were analysed by ANOVA for repeated measures with treatment as the main factor. Low energy availability and low NSC reduced the glucose and insulin and increased glucagone and urea blood levels. The increase of NSC in the diet of group H during the experiment may caused a reduction of the fibre digestibility after the period of adaptation of the rumen microflora and, as a paradox effect, suffered for an energetic lack with a subsequent activation of lipolysis and mobilization of their body reserves. Liver and muscular synthesis increase in group with a high energy availability.

  14. Complementarity of hydro and wind power: Improving the risk profile of energy inflows

    International Nuclear Information System (INIS)

    Denault, Michel; Dupuis, Debbie; Couture-Cardinal, Sebastien

    2009-01-01

    The complementarity of two renewable energy sources, namely hydro and wind, is investigated. We consider the diversification effect of wind power to reduce the risk of water inflow shortages, an important energy security concern for hydropower-based economic zones (e.g. Quebec and Norway). Our risk measure is based on the probability of a production deficit, in a manner akin to the value-at-risk, simulation analysis of financial portfolios. We examine whether the risk level of a mixed hydro-and-wind portfolio of generating assets improves on the risk of an all-hydro portfolio, by relaxing the dependence on water inflows and attenuating the impact of droughts. Copulas are used to model the dependence between the two sources of energy. The data considered, over the period 1958-2003, are for the province of Quebec, which possesses large hydro and wind resources. Our results indicate that for all scenarios considered, any proportion of wind up to 30% improves the production deficit risk profile of an all-hydro system. We can also estimate the value, in TW h, of any additional one percent of wind in the portfolio. (author)

  15. Leading Players of the Global Renewable Energy Equipment Industry. Overview of Groups - SWOTs - Benchmarking - Company Profiles and Financials

    International Nuclear Information System (INIS)

    2017-06-01

    This study presents: The medium-term and mega trends of the industry market developments and geographical segments; The competitive landscape and the main corporate rankings; The main conclusions of the report, summarised in 10 analytical slides. Content: 1. Overview: The Sector, Ranking, Performance Analysis; 2. Company Profiles: Toshiba, Vestas, Dong Energy, GE Renewable Energy, Siemens, Goldwind, First Solar, SunPower, Andritz, Yingli Green Energy; 3. Sources; 4. Annexes

  16. Legitimacy in Green: Pollution vs. Profit in Canadian Oil Refineries

    Directory of Open Access Journals (Sweden)

    Vanessa Magness

    2007-06-01

    light of changing societal expectations have created an external environment that encourages the development of new technologies that promote cost efficiencies and good environmental performance simultaneously.  Russo and Fouts (1997 argued that industries subject to rapid technological advance are well suited to respond to these changes in the external environment. The findings of this paper suggest that the petroleum refinery sector of the oil and gas industry may be meeting the challenge of the environmental movement.

  17. SPARO - A system for process analysis of refinery operations

    Energy Technology Data Exchange (ETDEWEB)

    Kesler, M.G.; Graham, J.; Weissbrod, J.

    1987-01-01

    SPARO is a customized process simulator for the PC, designed to review as well as to guide operations of hydrocarbon processing units. It can be applied to: gas plants or refinery gas recovery units; crude/vacuum towers with associated heat exchange; light ends units, such as reforming, alkylation and isomerization; fractionation and heat exchange units of Ethylene plants; aromatics and styrene units, and others. The main uses of SPARO are discussed in this paper.

  18. POSSIBILITIES OF CARBON DIOXIDE FIXATION BY MICROALGAE IN REFINERY

    OpenAIRE

    Šingliar, Michal; Mikulec, Jozef; Kušnir, Patrik; Polakovičova, Gabriela

    2013-01-01

    Capture and sequestration of carbon dioxide is one of the most critical challenges today for businesses and governments worldwide. Thousands of emitting power plants and industries worldwide face this costly challenge – reduce the CO2 emissions or pay penalties. One possibility for carbon dioxide sequestration is its fixation in microalgae. Microalgae can sequester CO2 from flue gases emitted from fossil fuel-fired refinery plants and units, thereby reducing emissions of a major greenhouse ga...

  19. A Novel Transporting System Model for Oil Refinery

    OpenAIRE

    Razman M. Tahar; Waleed K. Abduljabbar

    2010-01-01

    Problem statement: Oil refineries are widely used to store various liquids and gases. Petroleum products are in high demand. Oil companies have abundant resources of petroleum products in pipelines and storage tanks. Approach: Included are storage tanks at retail gasoline station, home heating oil tanks, lubricant storage at automotive service facilities, propane tanks in all sorts of application, and oil company terminals across the world. The aim of this study is to present a model by which...

  20. Hydrogen management in the MiRO refinery

    Energy Technology Data Exchange (ETDEWEB)

    Neumann, G. [Mineraloelraffinerie Oberrhein GmbH und Co. KG, Karlsruhe (Germany)

    2010-12-30

    The importance of hydrogen in refineries has increased over the last 20 years as new regulations affecting gasoline and diesel composition have been implemented throughout Europe and in an environment of increasingly stringent clean fuel regulations, decreasing heavy fuel oil demand and increasing heavy more sour crude supply. In Germany, the introduction of sulphur free gasoline and diesel with less than 10ppm sulphur(Auto Oil Program) and light home fuel oil with less than 50ppm this year were the last link in a long chain of environmental regulations, which had a considerable effect on the hydrogen demand in refineries. In the complex MiRO-refinery with a large FCC- and Coker-Unit for atmospheric residue conversion and a total throughput of more than 15 Mio.T/ a and more than 14 Mio.T/a crude oils of different origin from high sulphur, bituminous crudes to medium, low sulphur crudes for calcinate-production from green coke the only source of hydrogen for a long time was catalytic reforming. The only chance of balancing the hydrogen production and consumption was to improve the existing catalytic reforming and the optimisation of hydrogen recovery from waste or purge streams and the hydrogen network of the refinery. In 2007 a new hydrogen plant via steam reforming of natural gas went on stream. The main reason for this step was the shrinking market for gasoline in the last ten years and the blending of bio-ethanol into the gasoline pool, which released reforming capacities and the demand for octane. Another important issue is the production planning taking into account the potentials of hydrogen production via catalytic and steam reforming and the hydrogen consumption via desulphurisation and the saturation of olefins and (poly-)aromatics of the main product streams, gasoline, diesel and light home fuel oil. (orig.)

  1. Impact of dopant profiles on the end of range defects for low energy germanium preamorphized silicon

    International Nuclear Information System (INIS)

    Camillo-Castillo, R.A.; Law, M.E.; Jones, K.S.

    2004-01-01

    As the industry continues to aggressively scale CMOS technology, the shift to lower energy ion implantation becomes essential. The consequent shallower amorphous layers result in dopant profiles that are in closer proximity to the end of range (EOR) damage and therefore a better understanding of the interaction between the dopant atoms and the EOR is required. A study is conducted on the influence of dopant profiles on the behavior of the EOR defects. Czochralski-grown silicon wafers are preamorphized with 1 x 10 15 cm -2 , 10 keV Ge + ions and subsequently implanted with 1 x 10 15 cm -2 , 1 keV B + ions. A sequence of rapid thermal and furnace anneals are performed at 750 deg. C under a nitrogen ambient for periods of 1 s up to 6 h. Plan view transmission electron microscopy (PTEM) reveals a significant difference in the defect evolution for samples with and without boron, suggesting that the boron influences the evolution of the EOR defects. The extended defects observed for samples which contain boron appear as dot-like defects which are unstable and dissolve after very short anneal times. The defect evolution however, in samples without boron follows an Oswald ripening behavior and form {3 1 1}-type defects and dislocation loops. Hall effect measurements denote a high initial activation and subsequent deactivation of the dopant atoms which is characteristic of the formation of boron interstitial clusters. Diffusion analyses via secondary ion mass spectroscopy (SIMS) support this theory

  2. Determination of multi-element profiles of soil using energy dispersive X-ray fluorescence (EDXRF)

    International Nuclear Information System (INIS)

    Yu, K.N.; Yeung, Z.L.L.; Lee, L.Y.L.; Stokes, M.J.; Kwok, R.C.W.

    2002-01-01

    The source profile for soil in Hong Kong is important both for determination of the main air pollutant source in Hong Kong and for assessment of the impact of Asian dust storms on Hong Kong. Soil associated with different rock types have been sampled, and the concentrations of 19 chemical elements, Na, Al, Si, Ti, V, Cr, Mn, Fe, Co, K, Ca, Ni, Cu, Zn, Pb, Rb, Sr, Y and Zr, have been determined using energy dispersive X-ray fluorescence. A profile for the average soil for Hong Kong has been determined by taking average values for the different soil categories. The values for the Hong Kong soil are commensurate with values for rural soil derived by other workers, except that Hong Kong soil has much lower Fe and Ca concentrations. The abundance of Al, Ca and Fe in the average Hong Kong soil are 9.23%, 0.11% and 0.85%. We conclude that Ca provides a good marker element for identifying dust episodes in Hong Kong while Al does not

  3. Dynamic wedge, electron energy and beam profile Q.A. using an ionization chamber linear array

    International Nuclear Information System (INIS)

    Kenny, M.B.; Todd, S.P.

    1996-01-01

    Since the introduction of multi-modal linacs the quality assurance workload of a Physical Sciences department has increased dramatically. The advent of dynamic wedges has further complicated matters because of the need to invent accurate methods to perform Q.A. in a reasonable time. We have been using an ionization chamber linear array, the Thebes 7000 TM by Victoreen, Inc., for some years to measure X-ray and electron beam profiles. Two years ago we developed software to perform Q.A. on our dynamic wedges using the array and more recently included a routine to check electron beam energies using the method described by Rosenow, U.F. et al., Med. Phys. 18(1) 19-25. The integrated beam and profile management system has enabled us to maintain a comprehensive quality assurance programme on all our linaccs. Both our efficiency and accuracy have increased to the point where we are able to keep up with the greater number of tests required without an increase in staff or hours spent in quality assurance. In changing the processor from the Z80 of the Thebes console to the 486 of the PC we have also noticed a marked increase in the calibration stability of the array. (author)

  4. Parameters affecting profile shape of a high energy low current thin ion beam. Vol. 2

    Energy Technology Data Exchange (ETDEWEB)

    Abdel Salam, F W; Moustafa, O A; El-Khabeary, H [Accelerators Department, Nuclear Research Center, Atomic Energy Authority, Cairo, (Egypt)

    1996-03-01

    The shape of the profile of a high energy, low current beam of finite length has beam investigated. The beam profile shape depends on the initial beam radius, beam perveance, atomic mass number, charge state of ions, and beam length. These parameters can affect the relation between the initial beam radius and the corresponding final one. An optimum initial beam radius corresponding to minimum final beam at the target has been formulated and the relation between them is deduced taking account of the space charge effect. The minimum beam radius at the target was found to be equal to 2.3 of the optimum initial radius. It is concluded that in order to obtain a small beam radius at a target placed at a finite distance from an ion source, a beam of a low perveance, low atomic mass number and high number of electronic charge is required. This is an important detection for micro machining applications using the oscillating electron ion source which produces nearly paraxial thin beam of low perveance. 12 figs.

  5. Advanced purification of petroleum refinery wastewater by catalytic vacuum distillation.

    Science.gov (United States)

    Yan, Long; Ma, Hongzhu; Wang, Bo; Mao, Wei; Chen, Yashao

    2010-06-15

    In our work, a new process, catalytic vacuum distillation (CVD) was utilized for purification of petroleum refinery wastewater that was characteristic of high chemical oxygen demand (COD) and salinity. Moreover, various common promoters, like FeCl(3), kaolin, H(2)SO(4) and NaOH were investigated to improve the purification efficiency of CVD. Here, the purification efficiency was estimated by COD testing, electrolytic conductivity, UV-vis spectrum, gas chromatography-mass spectrometry (GC-MS) and pH value. The results showed that NaOH promoted CVD displayed higher efficiency in purification of refinery wastewater than other systems, where the pellucid effluents with low salinity and high COD removal efficiency (99%) were obtained after treatment, and the corresponding pH values of effluents varied from 7 to 9. Furthermore, environment estimation was also tested and the results showed that the effluent had no influence on plant growth. Thus, based on satisfied removal efficiency of COD and salinity achieved simultaneously, NaOH promoted CVD process is an effective approach to purify petroleum refinery wastewater. Copyright 2010 Elsevier B.V. All rights reserved.

  6. Economics and the refinery's CO2 emissions allocation problem

    International Nuclear Information System (INIS)

    Pierru, A.

    2007-01-01

    The establishment of a market for CO 2 emission rights in Europe leads oil-refining companies to add a cost associated with carbon emissions to the objective function of linear programming models used to manage refineries. These models may be used to compute the marginal contribution of each finished product to the CO 2 emissions of the refinery. Babusiaux (Oil. Gas Sci. Technol., 58, 2003, 685-692) has shown that, under some conditions, this marginal contribution is a relevant means of allocating the carbon emissions of the refinery. Thus, it can be used in a well-to-wheel Life Cycle Assessment. In fact, this result holds if the demand equations are the only binding constraints with a non-zero right-hand side coefficient. This is not the case for short-run models with fixed capacity. Then, allocating CO 2 emissions on a marginal basis tends to over-value (or undervalue) the total volume of emissions. In order to extend the existing methodology, we discuss two distinct solutions to this problem, inspired by economic theory: adapting either the Aumann-Shapley cost sharing method (Values of non-atomic games, 1974, Princeton University Press) or the Ramsey pricing formula (Econ. J., 37, 1927, 47-61; J. Econ. Theory, 3, 1971, 219-240). We compare these two solutions, with a strong argument in favour of Ramsey prices, based on the determination of the optimal environmental tax rate to which imported finished products should be subject. (author)

  7. Analysis and control of odors from petroleum refineries

    International Nuclear Information System (INIS)

    O'Brien, M.A.; Duffee, R.A.; Ostojic, N.

    1992-01-01

    This paper presents a proven approach used to effectively solve odor problems associated with atmospheric emissions from petroleum refineries. A systematic evaluation is first conducted to identify all emissions with the potential for off-site odor impacts. Sampling is then conducted and dynamic dilution olfactometry is used to quantify the odor emission rates of each source. Community odor surveys are performed simultaneously with the source sampling to quantitatively document the downwind odor impacts. Atmospheric dispersion modeling specifically designed for odor is then used to predict instantaneous odor occurrences at various receptor sites under meteorological conditions not actually encountered during the field study. The findings make it possible to rank sources by their odor emission rates and potential for odor impacts in the community. It is then possible to determine how much odor reduction is required to bring the present odor impacts of the individual sources to an acceptable level under worst-case meteorological conditions. Once the degree of control required is determined, control alternatives are selected and evaluated. Case histories have been selected to illustrate the application of this approach at petroleum refineries. They provide descriptions of odor assessment and abatement studies conducted specifically for refinery effluent treatment plant sources as well as process unit emission sources. The sources identified as needing control and the odor abatement measures taken are discussed

  8. Continues treatment of oily sludge at Colombian refineries

    International Nuclear Information System (INIS)

    Echeverria, Victor; Monsalve, Gladys; Vidales, Humberto

    2002-01-01

    The Colombian Petroleum institute - ICP, the research and development branch of Ecopetrol has developed a unique technological package used to treat oily sludge in a continuous way. The sludge comes from a refinery with 220000 barrels of crude per day load, located in the Middle Madgalena River Valley in Colombia. The technological package allows for a) the recovery of the hydrocarbon contained in oily wastes (up to 50%) b) the elimination of the oil contained in solid using a biodegradation process and, c) the availability economically and technically feasible solution to handle oily sludge generated in the refinery. The oily treated in this process come from maintenance of refinery's equipment and also from the physical chemical separation process at the industrial wastewater treatment plant. Oily sludge is a complex system where light and heavy oils, contaminated water and contaminated solids coexist in the form of direct, inverse and multiple emulsions. The comprehensive technological package allows the treatment of oily sludge in a cost effective way. ICP technological package developed includes technologies combining mechanical, thermal, chemical and electrostatic dehydration techniques and stimulated and intensive bioremediation to decontamination of solids saturated with residual oil. This technological package brings a solution to old environmental problem caused by the inappropriate final disposal of oily wastes such as storage in ponds, marshes and open pits: Nowadays wastes generated are treated in a continuous process that is environmentally friendly and economically profitable

  9. University of Maine Integrated Forest Product Refinery (IFPR) Technology Research

    Energy Technology Data Exchange (ETDEWEB)

    Pendse, Hemant P.

    2010-11-23

    This project supported research on science and technology that forms a basis for integrated forest product refinery for co-production of chemicals, fuels and materials using existing forest products industry infrastructure. Clear systems view of an Integrated Forest Product Refinery (IFPR) allowed development of a compelling business case for a small scale technology demonstration in Old Town ME for co-production of biofuels using cellulosic sugars along with pulp for the new owners of the facility resulting in an active project on Integrated Bio-Refinery (IBR) at the Old Town Fuel & Fiber. Work on production of advanced materials from woody biomass has led to active projects in bioplastics and carbon nanofibers. A lease for 40,000 sq. ft. high-bay space has been obtained to establish a Technology Research Center for IFPR technology validation on industrially relevant scale. UMaine forest bioproducts research initiative that began in April 2006 has led to establishment of a formal research institute beginning in March 2010.

  10. Treatment of Refinery Waste Water Using Environmental Friendly Adsorbent

    Science.gov (United States)

    Devi, M. Geetha; Al-Moshrafi, Samira Mohammed Khamis; Al Hudaifi, Alaa; Al Aisari, Buthaina Hamood

    2017-12-01

    This research evaluates the effectiveness of activated carbon prepared from walnut shell in the removal of pollutants from refinery waste water by adsorption technique. A series of batch experiments were carried out by varying the effluent solution pH, stirring time, stirring speed and adsorbent dosage in the reduction of pollutants from refinery effluent. Characterization of the adsorbent was performed using Scanning Electron Microscopy (SEM), Brunauer Emmett and Teller (BET) isotherm and Fourier Transform Infrared (FTIR) Spectroscopy. The best quality activated carbon was obtained with a particle size of 0.75 µm, activation temperature of 800 °C and activation time 24 h. The maximum BET surface area obtained was 165.2653 m2/g. The experimental results demonstrates that the highest percentage reduction in COD was 79%, using 0.6 g walnut shell powder at an optimum stirring speed of 100 rpm, at pH 6 and 120 min of contact time. The outcome of the result shows that walnut shell carbon is a potentially useful adsorbent for the removal of pollutants from refinery waste water.

  11. Assessment of accidental refinery wastewater discharge: a case study

    Energy Technology Data Exchange (ETDEWEB)

    Bandyopadhyay, Amitava [University of Calcutta, Department of Chemical Engineering, Kolkata (India)

    2011-04-15

    The physicochemical qualities of an accidental discharge of refinery liquid waste, water, and soil sediment of that effluent-receiving water body (canal) were investigated. Analyses of the discharge, qualities of water, and sediment of the canal showed high parametric concentrations. Investigations revealed that the discharge took place form the spent caustic that was generated from the caustic wash tower of Fluidized Catalytic Cracker of the refinery. A simple but realistic model was suggested for the remediation of sediments of the canal with an estimated cost of about US $1.86 million. Recommendations were made to prevent such discharges and to revise thoroughly the Indian effluent discharge standards in force for petroleum oil refinery. Subsequently, revised standards were notified under Indian guidelines. Interestingly, cyanide besides many other parameters was introduced into these standards. Furthermore, Volatile Organic Compound (VOC) was also stipulated as an emission parameter from the waste water treatment plants. Concentration- and mass-based standards thus promulgated were stricter than the existing standards. (orig.)

  12. Molybdenum carbide nanoparticles as catalysts for oil sands upgrading: Dynamics and free-energy profiles

    International Nuclear Information System (INIS)

    Liu, Xingchen; Salahub, Dennis R.

    2015-01-01

    There is no doubt that a huge gap exists in understanding heterogeneous catalysis between a cluster model of a few atoms and a bulk model of periodic slabs. Nanoparticles, which are crucial in heterogeneous catalysis in industry, lie in the middle of the gap. We present here our work on the computational modelling of molybdenum carbide nanoparticles (MCNPs) as the catalysts for the upgrading of oil sands in the in-situ environment, using benzene hydrogenation as a model reaction. With a cluster model, efforts were first made to understand the mechanism of the reaction with a density functional theory (DFT) study on the adsorption of benzene and its hydrogenation product – cyclohexane, as well as the cyclic hydrogenation reaction intermediates on the Mo 2 C(0001) surface. From the thermodynamic data, along with literature information, it was found that the benzene hydrogenation reaction on molybdenum carbide happens most likely through a Langmuir-Hinshelwood mechanism with the gradual lifting up of the benzene molecule. The electron localization function (ELF) was then used to help understand the nature of the interactions between the MCNPs, identifying strong multi-center interactions between the adsorbates and the MCNPs. To enable the treatment of larger nanoparticles, a fast semi-empirical density functional tight-binding (DFTB) method was parameterized. With this method, the potential energy profiles of benzene hydrogenation reactions on different sizes of MCNPs are calculated. The study was then extended to consider a MCNP embedded in solvent (benzene), using a quantum mechanical (DFTB) / molecular mechanical approach. Calculations on the free energies profiles with the umbrella sampling method show that the entropy of the MCNPs and the solvent are essential in understanding the catalytic activity of the transition metal related nanoparticles for solid/liquid heterogeneous catalysis

  13. Quantitative considerations in medium energy ion scattering depth profiling analysis of nanolayers

    Energy Technology Data Exchange (ETDEWEB)

    Zalm, P.C.; Bailey, P. [International Institute for Accelerator Applications, University of Huddersfield, Queensgate, Huddersfield HD1 3DH (United Kingdom); Reading, M.A. [Physics and Materials Research Centre, University of Salford, Salford M5 4WT (United Kingdom); Rossall, A.K. [International Institute for Accelerator Applications, University of Huddersfield, Queensgate, Huddersfield HD1 3DH (United Kingdom); Berg, J.A. van den, E-mail: j.vandenberg@hud.ac.uk [International Institute for Accelerator Applications, University of Huddersfield, Queensgate, Huddersfield HD1 3DH (United Kingdom)

    2016-11-15

    The high depth resolution capability of medium energy ion scattering (MEIS) is becoming increasingly relevant to the characterisation of nanolayers in e.g. microelectronics. In this paper we examine the attainable quantitative accuracy of MEIS depth profiling. Transparent but reliable analytical calculations are used to illustrate what can ultimately be achieved for dilute impurities in a silicon matrix and the significant element-dependence of the depth scale, for instance, is illustrated this way. Furthermore, the signal intensity-to-concentration conversion and its dependence on the depth of scattering is addressed. Notably, deviations from the Rutherford scattering cross section due to screening effects resulting in a non-coulombic interaction potential and the reduction of the yield owing to neutralization of the exiting, backscattered H{sup +} and He{sup +} projectiles are evaluated. The former mainly affects the scattering off heavy target atoms while the latter is most severe for scattering off light target atoms and can be less accurately predicted. However, a pragmatic approach employing an extensive data set of measured ion fractions for both H{sup +} and He{sup +} ions scattered off a range of surfaces, allows its parameterization. This has enabled the combination of both effects, which provides essential information regarding the yield dependence both on the projectile energy and the mass of the scattering atom. Although, absolute quantification, especially when using He{sup +}, may not always be achievable, relative quantification in which the sum of all species in a layer adds up to 100%, is generally possible. This conclusion is supported by the provision of some examples of MEIS derived depth profiles of nanolayers. Finally, the relative benefits of either using H{sup +} or He{sup +} ions are briefly considered.

  14. Molybdenum carbide nanoparticles as catalysts for oil sands upgrading: Dynamics and free-energy profiles

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Xingchen; Salahub, Dennis R. [Department of Chemistry, Institute for Quantum Science and Technology, and Centre for Molecular Simulation, University of Calgary, 2500 University Drive NW, Calgary, Alberta, Canada T2N 1N4 (Canada)

    2015-12-31

    There is no doubt that a huge gap exists in understanding heterogeneous catalysis between a cluster model of a few atoms and a bulk model of periodic slabs. Nanoparticles, which are crucial in heterogeneous catalysis in industry, lie in the middle of the gap. We present here our work on the computational modelling of molybdenum carbide nanoparticles (MCNPs) as the catalysts for the upgrading of oil sands in the in-situ environment, using benzene hydrogenation as a model reaction. With a cluster model, efforts were first made to understand the mechanism of the reaction with a density functional theory (DFT) study on the adsorption of benzene and its hydrogenation product – cyclohexane, as well as the cyclic hydrogenation reaction intermediates on the Mo{sub 2}C(0001) surface. From the thermodynamic data, along with literature information, it was found that the benzene hydrogenation reaction on molybdenum carbide happens most likely through a Langmuir-Hinshelwood mechanism with the gradual lifting up of the benzene molecule. The electron localization function (ELF) was then used to help understand the nature of the interactions between the MCNPs, identifying strong multi-center interactions between the adsorbates and the MCNPs. To enable the treatment of larger nanoparticles, a fast semi-empirical density functional tight-binding (DFTB) method was parameterized. With this method, the potential energy profiles of benzene hydrogenation reactions on different sizes of MCNPs are calculated. The study was then extended to consider a MCNP embedded in solvent (benzene), using a quantum mechanical (DFTB) / molecular mechanical approach. Calculations on the free energies profiles with the umbrella sampling method show that the entropy of the MCNPs and the solvent are essential in understanding the catalytic activity of the transition metal related nanoparticles for solid/liquid heterogeneous catalysis.

  15. Electrokinetic remediation of lead and nickel in land farming soil of petroleum refinery; Remediacao eletrocinetica de chumbo e niquel em solos de landfarming de uma refinaria de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Guaracho, Viviane V.; Ponte, Maria Jose J.S.; Adamoski, Luiz Felipe [Universidade Federal do Parana (UFPR), Curitiba, PR (Brazil)

    2004-07-01

    In many areas in the world, the ground has been seriously contaminated, had to practical of inadequate disposal and pollutant industrial activities. This polluted soil becomes a threat to the environment for presenting toxical substances, as the heavy metals. The alternative to solve this threat is a technique of electrokinetic remediation, which has been considered promising because it presents an excellent potential of recovery of places contaminated by heavy metals. This technique consists on the application of a direct current of low intensity through the ground between two or more electrodes. This way, the objective of this work is to evaluate the performance of the electrokinetic remediation for removal of Lead and Nickel, from the ground of land farming from petroleum refineries. The ground will be simulated using contaminated sand with nickel and lead nitrate with concentrations previously established. For a reduction in the experimental costs, one technique of statistical planning will be used. Parameters will be modified as: concentration of ions, applied potential and time. Through the concentration profile it is intended to calculate the coefficient of mass transport in order to get a correlation between the concentration and the flow of the species. Aiming at a economical evaluation of the reactor, the current and the energy consumption efficiencies will be evaluated. (author)

  16. Thermoeconomic and environmental assessment of a crude oil distillation unit of a Nigerian refinery

    International Nuclear Information System (INIS)

    Waheed, M.A.; Oni, A.O.; Adejuyigbe, S.B.; Adewumi, B.A.

    2014-01-01

    The renovation of refineries should be aimed at achieving the highest possible technical efficiencies at a considerable investment cost and not only at replacing damaged components to attain full capacity utilisation. This study examined a crude distillation unit (CDU) of a Nigerian refinery plant comprising the atmospheric distillation unit (ADU), vacuum distillation unit (VDU), preflash unit (PFU), splitter unit (SPU), stabiliser unit (SBU) and heat exchanger network (HEN) to determine critical areas of inefficiencies as the plant managements plan renovation. Using real plant data, the CDU was simulated with Aspen Hysys ® and the thermoeconomic and environmental analyses were carried out. The results show that the energy and exergy efficiencies of the CDU were 9.0 and 4.0% respectively. The specific CO 2 emission was 3.67 kg CO 2 /bbl. The highly inefficient subunits accounting for 77.4 and 90.0% of the overall energy and exergy losses respectively and 60.3% of the emission released were the PFU, ADU and HEN. The highly inefficient components are the furnaces which accounted for 51.6% of the overall exergy losses. The environmental and economic analysis also indicated that these components are the most potent for improvement. The columns of the PFU and ADU should be revamped to reduce their energy demands and the HEN should be modified to minimise effluent losses. - Highlights: •The assessment of a crude distillation unit (CDU) in Nigeria was carried out. •The assessment considered thermodynamic, thermoeconomic and environment analysis. •The assessment revealed areas with poor performance in the CDU. •Large thermodynamic and economic losses are responsible for the poor performance. •Areas with large losses and emission rate should be targeted for improvement

  17. Thermoeconomic and environmental assessment of a crude oil distillation unit of a Nigerian refinery

    Energy Technology Data Exchange (ETDEWEB)

    Waheed, M. A. [Department of Mechanical Engineering, Federal University of Agriculture, Abeokuta, P.M.B. 2240, Abeokuta, Ogun State (Nigeria); Oni, A.O., E-mail: fem2day@yahoo.com [Department of Mechanical Engineering, Federal University of Agriculture, Abeokuta, P.M.B. 2240, Abeokuta, Ogun State (Nigeria); Adejuyigbe, S. B. [Department of Mechanical Engineering, Federal University of Agriculture, Abeokuta, P.M.B. 2240, Abeokuta, Ogun State (Nigeria); Adewumi, B. A. [Department of Agricultural Engineering, Federal University of Agriculture, Abeokuta, P.M.B. 2240, Abeokuta, Ogun State (Nigeria)

    2014-05-01

    The renovation of refineries should be aimed at achieving the highest possible technical efficiencies at a considerable investment cost and not only at replacing damaged components to attain full capacity utilisation. This study examined a crude distillation unit (CDU) of a Nigerian refinery plant comprising the atmospheric distillation unit (ADU), vacuum distillation unit (VDU), preflash unit (PFU), splitter unit (SPU), stabiliser unit (SBU) and heat exchanger network (HEN) to determine critical areas of inefficiencies as the plant managements plan renovation. Using real plant data, the CDU was simulated with Aspen Hysys{sup ®} and the thermoeconomic and environmental analyses were carried out. The results show that the energy and exergy efficiencies of the CDU were 9.0 and 4.0% respectively. The specific CO{sub 2} emission was 3.67 kg CO{sub 2}/bbl. The highly inefficient subunits accounting for 77.4 and 90.0% of the overall energy and exergy losses respectively and 60.3% of the emission released were the PFU, ADU and HEN. The highly inefficient components are the furnaces which accounted for 51.6% of the overall exergy losses. The environmental and economic analysis also indicated that these components are the most potent for improvement. The columns of the PFU and ADU should be revamped to reduce their energy demands and the HEN should be modified to minimise effluent losses. - Highlights: •The assessment of a crude distillation unit (CDU) in Nigeria was carried out. •The assessment considered thermodynamic, thermoeconomic and environment analysis. •The assessment revealed areas with poor performance in the CDU. •Large thermodynamic and economic losses are responsible for the poor performance. •Areas with large losses and emission rate should be targeted for improvement.

  18. Gas turbine application in power plants of Mexican refineries; Aplicacion de turbinas de gas en plantas de fuerza de refinerias mexicanas

    Energy Technology Data Exchange (ETDEWEB)

    Alcaraz Calderon, A. M.; Rodriguez Martinez, H.; Garcia Paredes, Job; Morales Guillen, Magdalena; Manzanares Papayanapolous, Emilio [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)]. E-mail: malcaraz@iie.org.mx; jhrm@iie.org.mx; jgarcia@iie.org.mx; mmmg@iie.org.mx; emp@iie.org.mx

    2010-11-15

    This article presents an overview of the application to have the gas turbine power generation systems, electric and steam for Mexican refineries. First there is a general description of the gas turbines and heat recovery (system components CHP) and CHP schemes are based on gas turbines capable of use in Mexican refineries. Subsequently referred to the characteristics of energy consumption (steam and electricity) from Mexican refineries and performs a technical analysis of CHP schemes based on gas turbines from the point of view of rates Q/W, power efficiencies and combined concluded that by their nature are very useful for refinery and gives some recommendations for improved implementation. [Spanish] En este articulo se presenta una vision general de la aplicacion que tienen las turbinas de gas en sistemas de generacion de energia electrica y vapor para refinerias mexicanas. Primeramente se da una descripcion general de las turbinas de gas y recuperadores de calor (componentes principales del sistema de cogeneracion) y se muestran los esquemas de cogeneracion basados en turbinas de gas susceptibles de utilizar en refinerias mexicanas. Posteriormente se mencionan las caracteristicas de consumos energeticos (vapor y energia electrica) de las refinerias mexicanas y se realiza un analisis tecnico de los esquemas de cogeneracion basado en turbinas de gas desde el punto de vista de tasas Q/W, eficiencias electricas y combinadas, concluyendose que por sus caracteristicas son muy utiles para refinerias y se dan algunas recomendaciones para su mejor aplicacion.

  19. Thermodynamic evaluation of distillation columns using exergy loss profiles: a case study on the crude oil atmospheric distillation column

    Energy Technology Data Exchange (ETDEWEB)

    Tarighaleslami, Amir Hossein [Mahshahr Branch, Islamic Azad University, Chemical Engineering Faculty, Mahshar, Khouzestan (Iran, Islamic Republic of); Omidkhah, Mohammad Reza [Tarbiat Modares University, Chemical Engineering Department, Faculty of Engineering, Tehran (Iran, Islamic Republic of); Ghannadzadeh, Ali [University of Toulouse, Department of Process and System Engineering, Chemical Engineering Laboratory, Toulouse (France); Hoseinzadeh Hesas, Roozbeh [University of Malaya, Chemical Engineering Department, Faculty of Engineering, Kuala Lumpur (Malaysia)

    2012-06-15

    This paper presents a case study on the crude oil atmospheric distillation column of Tabriz refinery plant to show the applicability of exergy loss profiles in thermodynamic examination of the different retrofit options. The atmospheric distillation column of Tabriz refinery has been revamped as a consequence of increase of the plant capacity to 100,000 bpd. To cover the deficit of feedstock of the revamped unit, a blend of the existing feedstock with imported crude oil is used as a feedstock. However, to investigate how the blend of these two different types of crudes as a feedstock has an influence on the operating conditions, the examination of the column is needed. Exergy as a comprehensive thermodynamic property which translates the temperature, pressure and composition change into a common unit has been chosen to evaluate the distillation column thermodynamically. Furthermore, the exergy loss profile of the base case serves as a scoping tool to pinpoint the source of inefficiencies. Then, the exergy loss profile as a screening tool has found the retrofit options which are likely to yield greatest energy saving from a list of retrofit options proposed by the industrial partner. In the presented case study, the exergy loss profile identifies the best retrofit option with 17.16% reduction in exergy losses, which finally lead to 3.6% reduction of primary fuel demand. (orig.)

  20. Identification of genes and pathways related to phenol degradation in metagenomic libraries from petroleum refinery wastewater.

    Directory of Open Access Journals (Sweden)

    Cynthia C Silva

    Full Text Available Two fosmid libraries, totaling 13,200 clones, were obtained from bioreactor sludge of petroleum refinery wastewater treatment system. The library screening based on PCR and biological activity assays revealed more than 400 positive clones for phenol degradation. From these, 100 clones were randomly selected for pyrosequencing in order to evaluate the genetic potential of the microorganisms present in wastewater treatment plant for biodegradation, focusing mainly on novel genes and pathways of phenol and aromatic compound degradation. The sequence analysis of selected clones yielded 129,635 reads at an estimated 17-fold coverage. The phylogenetic analysis showed Burkholderiales and Rhodocyclales as the most abundant orders among the selected fosmid clones. The MG-RAST analysis revealed a broad metabolic profile with important functions for wastewater treatment, including metabolism of aromatic compounds, nitrogen, sulphur and phosphorus. The predicted 2,276 proteins included phenol hydroxylases and cathecol 2,3- dioxygenases, involved in the catabolism of aromatic compounds, such as phenol, byphenol, benzoate and phenylpropanoid. The sequencing of one fosmid insert of 33 kb unraveled the gene that permitted the host, Escherichia coli EPI300, to grow in the presence of aromatic compounds. Additionally, the comparison of the whole fosmid sequence against bacterial genomes deposited in GenBank showed that about 90% of sequence showed no identity to known sequences of Proteobacteria deposited in the NCBI database. This study surveyed the functional potential of fosmid clones for aromatic compound degradation and contributed to our knowledge of the biodegradative capacity and pathways of microbial assemblages present in refinery wastewater treatment system.

  1. Projection of opportunities for a refinery in a global long-term scenario; Projecao de oportunidades para uma refinaria em cenario mundial de longo prazo

    Energy Technology Data Exchange (ETDEWEB)

    Lucena, Sergio Cunha de; Perisse, Juarez Barbosa; Farah, Marco Antonio; Faria, Marcia Dardari Castanheira [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil); Paredes, Marcio Luis Lyra [Universidade do Estado do Rio de Janeiro (UERJ), RJ (Brazil). Inst. de Quimica

    2012-07-01

    The outlook for 2050 pointed out by companies associated with research into energy on the globe indicate that global energy production still fairly representative in oil. In the future the relative contribution related to the consumption of oil in world energy matrix reduces, however increases in absolute values. That is, the oil market through its derivatives, is still the focus of great opportunities. These business opportunities will be as close as the flexibility of production derived from a particular refinery permits. Moreover, production flexibility is associated to investment costs. This paper focuses on the evaluation of different configurations of an oil refinery and shows that adding complexity to a refining scheme should not always be regarded as the best strategic path. (author)

  2. Free surface profiles in river flows: Can standard energy-based gradually-varied flow computations be pursued?

    Science.gov (United States)

    Cantero, Francisco; Castro-Orgaz, Oscar; Garcia-Marín, Amanda; Ayuso, José Luis; Dey, Subhasish

    2015-10-01

    Is the energy equation for gradually-varied flow the best approximation for the free surface profile computations in river flows? Determination of flood inundation in rivers and natural waterways is based on the hydraulic computation of flow profiles. This is usually done using energy-based gradually-varied flow models, like HEC-RAS, that adopts a vertical division method for discharge prediction in compound channel sections. However, this discharge prediction method is not so accurate in the context of advancements over the last three decades. This paper firstly presents a study of the impact of discharge prediction on the gradually-varied flow computations by comparing thirteen different methods for compound channels, where both energy and momentum equations are applied. The discharge, velocity distribution coefficients, specific energy, momentum and flow profiles are determined. After the study of gradually-varied flow predictions, a new theory is developed to produce higher-order energy and momentum equations for rapidly-varied flow in compound channels. These generalized equations enable to describe the flow profiles with more generality than the gradually-varied flow computations. As an outcome, results of gradually-varied flow provide realistic conclusions for computations of flow in compound channels, showing that momentum-based models are in general more accurate; whereas the new theory developed for rapidly-varied flow opens a new research direction, so far not investigated in flows through compound channels.

  3. Gasoline from biomass through refinery-friendly carbohydrate-based bio-oil produced by ketalization.

    Science.gov (United States)

    Batalha, Nuno; da Silva, Alessandra V; de Souza, Matheus O; da Costa, Bruna M C; Gomes, Elisa S; Silva, Thiago C; Barros, Thalita G; Gonçalves, Maria L A; Caramão, Elina B; dos Santos, Luciana R M; Almeida, Marlon B B; de Souza, Rodrigo O M A; Lam, Yiu L; Carvalho, Nakédia M F; Miranda, Leandro S M; Pereira, Marcelo M

    2014-06-01

    The introduction of biomass-derived compounds as an alternative feed into the refinery structure that already exists can potentially converge energy uses with ecological sustainability. Herein, we present an approach to produce a bio-oil based on carbohydrate-derived isopropylidene ketals obtained by reaction with acetone under acidic conditions directly from second-generation biomass. The obtained bio-oil showed a greater chemical inertness and miscibility with gasoil than typical bio-oil from fast pyrolysis. Catalytic upgrading of the bio-oil over zeolites (USY and Beta) yielded gasoline with a high octane number. Moreover, the co-processing of gasoil and bio-oil improved the gasoline yield and quality compared to pure gasoil and also reduced the amount of oxygenated compounds and coke compared with pure bio-oil, which demonstrates a synergistic effect. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. Econometric model of the petroleum industry. [Determining crude supply and outputs/prices of refinery products

    Energy Technology Data Exchange (ETDEWEB)

    Rice, P [Oak Ridge National Lab., TN; Smith, V K

    1977-11-01

    This paper describes a forty-two nonlinear equation model of the U.S. petroleum industry estimated over the period 1946 to 1973. The model specifies refinery outputs and prices as being simultaneously determined by market forces while the domestic output of crude oil is determined in a block-recursive segment of the model. The simultaneous behavioral equations are estimated with nonlinear two-stage least-squares adjusted to reflect the implications of autocorrelation for those equations where it appears to be a problem. A multi-period sample simulation, together with forecasts for 1974 and 1975 are used to evaluate the model's performance. Finally, it is used to forecast to 1985 under two scenarios and compared with the Federal Energy Administration's forecast for the same period. 2 figures, 8 tables, 38 references.

  5. Free energy profiles of cocaine esterase-cocaine binding process by molecular dynamics and potential of mean force simulations.

    Science.gov (United States)

    Zhang, Yuxin; Huang, Xiaoqin; Han, Keli; Zheng, Fang; Zhan, Chang-Guo

    2016-11-25

    The combined molecular dynamics (MD) and potential of mean force (PMF) simulations have been performed to determine the free energy profile of the CocE)-(+)-cocaine binding process in comparison with that of the corresponding CocE-(-)-cocaine binding process. According to the MD simulations, the equilibrium CocE-(+)-cocaine binding mode is similar to the CocE-(-)-cocaine binding mode. However, based on the simulated free energy profiles, a significant free energy barrier (∼5 kcal/mol) exists in the CocE-(+)-cocaine binding process whereas no obvious free energy barrier exists in the CocE-(-)-cocaine binding process, although the free energy barrier of ∼5 kcal/mol is not high enough to really slow down the CocE-(+)-cocaine binding process. In addition, the obtained free energy profiles also demonstrate that (+)-cocaine and (-)-cocaine have very close binding free energies with CocE, with a negligible difference (∼0.2 kcal/mol), which is qualitatively consistent with the nearly same experimental K M values of the CocE enzyme for (+)-cocaine and (-)-cocaine. The consistency between the computational results and available experimental data suggests that the mechanistic insights obtained from this study are reasonable. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

  6. Energy demand and thermal comfort of HVAC systems with thermally activated building systems as a function of user profile

    Science.gov (United States)

    Pałaszyńska, Katarzyna; Bandurski, Karol; Porowski, Mieczysław

    2017-11-01

    Thermally Activated Building Systems (TABS) are a way to use building structure as a thermal energy storage. As a result, renewable energy sources may be used more efficiently. The paper presents numerical analysis of a HVAC system with TABS energy demand and indoor thermal comfort of a representative room in a non-residential building (governmental, commercial, educational). The purpose of analysis is to investigate the influence of a user profile on system performance. The time span of the analysis is one year - a typical meteorological year. The model was prepared using a generally accepted simulation tool - TRNSYS 17. The results help to better understand the interaction of a user profile with TABS. Therefore they are important for the development of optimal control algorithms for energy efficient buildings equipped with such systems.

  7. Derivation of the radial profile of ion temperature from the measured energy spectra of charge-exchanged neutrals

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, K; Hiraki, N; Toi, K; Itoh, S

    1980-01-01

    In the TRIAM-1 tokamak the energy spectra of charge-exchanged neutrals are observed by scanning the neutral energy analyzer vertically. The measured ion temperature obtained from the only energy spectrum observed in the peripheral region is much higher than that predicted by the neoclassical transport theory because of reflection (backscattering) of neutrals at the wall. The actual ion temperature profile is derived from all observed energy spectra by the numerical code in which a wall-reflection effect of neutrals and an impermeability of plasma are taken into account. The reflection coefficient is adjusted so that the calculated ion temperature profile should be the best fit for the ion temperatures measured by the Doppler broadening of the visible lines He II 4686 A and H-alpha at the relevant radial positions.

  8. Derivation of the radial profile of ion temperature from the 'measured' energy spectra of charge-exchanged neutrals

    International Nuclear Information System (INIS)

    Nakamura, Kazuo; Hiraki, Naoji; Toi, Kazuo; Itoh, Satoshi

    1980-01-01

    In the TRIAM-1 tokamak the energy spectra of charge-exchanged neutrals are observed by scanning the neutral energy analyzer vertically. The ''measured'' ion temperature obtained from only energy spectrum observed in the peripheral region is much higher than that predicted by the neoclassical transport theory because of reflection (backscattering) of neutrals at the wall. The ''actual'' ion temperature profile is derived from all observed energy spectra by using the numerical code in which a wall-reflection effect of neutrals and an impermeability of plasma are taken into account. In this numerical analysis, the reflection coefficient is adjusted so that the above calculated ion temperature profile should be best fit for the ion temperatures measured by the Doppler broadening of the visible lines HeII 4686 A and H sub(α) at the relevant radial positions. (author)

  9. Derivation of the radial profile of ion temperature from the 'measured' energy spectra of charge-exchanged neutrals

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, K; Hiraki, N; Toi, K; Itoh, S [Kyushu Univ., Fukuoka (Japan). Research Inst. for Applied Mechanics

    1980-07-01

    In the TRIAM-1 tokamak the energy spectra of charge-exchanged neutrals are observed by scanning the neutral energy analyzer vertically. The ''measured'' ion temperature obtained from only energy spectrum observed in the peripheral region is much higher than that predicted by the neoclassical transport theory because of reflection (backscattering) of neutrals at the wall. The ''actual'' ion temperature profile is derived from all observed energy spectra by using the numerical code in which a wall-reflection effect of neutrals and an impermeability of plasma are taken into account. In this numerical analysis, the reflection coefficient is adjusted so that the above calculated ion temperature profile should be best fit for the ion temperatures measured by the Doppler broadening of the visible lines HeII 4686 A and H sub(..cap alpha..) at the relevant radial positions.

  10. Energy demand and thermal comfort of HVAC systems with thermally activated building systems as a function of user profile

    Directory of Open Access Journals (Sweden)

    Pałaszyńska Katarzyna

    2017-01-01

    Full Text Available Thermally Activated Building Systems (TABS are a way to use building structure as a thermal energy storage. As a result, renewable energy sources may be used more efficiently. The paper presents numerical analysis of a HVAC system with TABS energy demand and indoor thermal comfort of a representative room in a non-residential building (governmental, commercial, educational. The purpose of analysis is to investigate the influence of a user profile on system performance. The time span of the analysis is one year – a typical meteorological year. The model was prepared using a generally accepted simulation tool – TRNSYS 17. The results help to better understand the interaction of a user profile with TABS. Therefore they are important for the development of optimal control algorithms for energy efficient buildings equipped with such systems.

  11. Ion temperature profiles from the plasma center to the edge of ASDEX combining high and low energy CX-diagnostics

    International Nuclear Information System (INIS)

    Verbeek, H.; Heinrich, O.; Schneider, R.; Fahrbach, H.U.; Herrmann, W.; Neuhauser, J.; Stroth, U.; Reiter, D.

    1992-01-01

    The charge exchange (CX) neutral energy distribution from ASDEX measured with the conventional neutral particle analyzers (NPA) at energies >500 eV are combined with the low energy CX spectra from the low energy neutral analyzer (LENA). In the region of overlap their shapes fit each other very well. With the 3D EIRENE code the neutral gas was simulated and ion temperature (T i ) profiles from the center to the edge are obtained. The T i values at the separatrix and the edge based on the LENA data are considerably lower than those suggested earlier from the NPA data. This is attributed to the different energy ranges - high energies for the NPA, low energies for LENA - that are used for the T i evaluation. (orig.)

  12. Linear energy transfer effects on time profiles of scintillation of Ce-doped LiCaAlF6 crystals

    International Nuclear Information System (INIS)

    Yanagida, Takayuki; Koshimizu, Masanori; Kurashima, Satoshi; Iwamatsu, Kazuhiro; Kimura, Atsushi; Taguchi, Mitsumasa; Fujimoto, Yutaka; Asai, Keisuke

    2015-01-01

    We measured temporal profiles of the scintillation of Ce-doped LiCaAlF 6 scintillator crystals at different linear energy transfers (LETs). Based on the comparison of high-LET temporal profiles with those at low LET, a fast component was observed only at low LET. The disappearance of the fast component at high LET is tentatively ascribed to the quenching of excited states at crystal defects owing to the interaction between excited states via the Auger process. In addition, the rise and the initial decay behavior were dependent on the LET. This LET-dependent behavior is explained by an acceleration process and a deceleration process in energy transfer at high LET. The LET-dependent temporal profiles provide the basis for a discrimination technique of gamma-ray and neutron detection events using these scintillators based on the nuclear reaction, 6 Li(n,α)t.

  13. Efficient Construction of Free Energy Profiles of Breathing Metal-Organic Frameworks Using Advanced Molecular Dynamics Simulations.

    Science.gov (United States)

    Demuynck, Ruben; Rogge, Sven M J; Vanduyfhuys, Louis; Wieme, Jelle; Waroquier, Michel; Van Speybroeck, Veronique

    2017-12-12

    In order to reliably predict and understand the breathing behavior of highly flexible metal-organic frameworks from thermodynamic considerations, an accurate estimation of the free energy difference between their different metastable states is a prerequisite. Herein, a variety of free energy estimation methods are thoroughly tested for their ability to construct the free energy profile as a function of the unit cell volume of MIL-53(Al). The methods comprise free energy perturbation, thermodynamic integration, umbrella sampling, metadynamics, and variationally enhanced sampling. A series of molecular dynamics simulations have been performed in the frame of each of the five methods to describe structural transformations in flexible materials with the volume as the collective variable, which offers a unique opportunity to assess their computational efficiency. Subsequently, the most efficient method, umbrella sampling, is used to construct an accurate free energy profile at different temperatures for MIL-53(Al) from first principles at the PBE+D3(BJ) level of theory. This study yields insight into the importance of the different aspects such as entropy contributions and anharmonic contributions on the resulting free energy profile. As such, this thorough study provides unparalleled insight in the thermodynamics of the large structural deformations of flexible materials.

  14. Efficient Construction of Free Energy Profiles of Breathing Metal–Organic Frameworks Using Advanced Molecular Dynamics Simulations

    Science.gov (United States)

    2017-01-01

    In order to reliably predict and understand the breathing behavior of highly flexible metal–organic frameworks from thermodynamic considerations, an accurate estimation of the free energy difference between their different metastable states is a prerequisite. Herein, a variety of free energy estimation methods are thoroughly tested for their ability to construct the free energy profile as a function of the unit cell volume of MIL-53(Al). The methods comprise free energy perturbation, thermodynamic integration, umbrella sampling, metadynamics, and variationally enhanced sampling. A series of molecular dynamics simulations have been performed in the frame of each of the five methods to describe structural transformations in flexible materials with the volume as the collective variable, which offers a unique opportunity to assess their computational efficiency. Subsequently, the most efficient method, umbrella sampling, is used to construct an accurate free energy profile at different temperatures for MIL-53(Al) from first principles at the PBE+D3(BJ) level of theory. This study yields insight into the importance of the different aspects such as entropy contributions and anharmonic contributions on the resulting free energy profile. As such, this thorough study provides unparalleled insight in the thermodynamics of the large structural deformations of flexible materials. PMID:29131647

  15. Model-centered approach to early planning and design of an eco-industrial park around an oil refinery.

    Science.gov (United States)

    Zhang, Xiangping; Strømman, Anders H; Solli, Christian; Hertwich, Edgar G

    2008-07-01

    Industrial symbiosis promises environmental and economic gains through a utilization of the waste of some processes as a resource for other processes. Because of the costs and difficulties of transporting some wastes, the largest theoretical potential for industrial symbiosis is given when facilities are colocated in an eco-industrial park (EIP). This study proposes a model-centered approach with an eight-step procedure for the early planning and design of an eco-industrial park considering technical and environmental factors. Chemical process simulation software was used to model the energy and material flows among the prospective members and to quantify the benefits of integration among different firms in terms of energy and resources saved as compared to a reference situation. Process simulation was based on a combination of physical models of industrial processes and empirical models. The modeling allows for the development and evaluation of different collaboration opportunities and configurations. It also enables testing chosen configurations under hypothetical situations or external conditions. We present a case study around an existing oil and gas refinery in Mongstad, Norway. We used the approach to propose the colocation of a number of industrial facilities around the refinery, focused on integrating energy use among the facilities. An EIP with six main members was designed and simulated, matching new hypothetical members in size to the existing operations, modeling material and energy flows in the EIP, and assessing these in terms of carbon and hydrogen flows.

  16. Refinery evaluation of optical imaging to locate fugitive emissions.

    Science.gov (United States)

    Robinson, Donald R; Luke-Boone, Ronke; Aggarwal, Vineet; Harris, Buzz; Anderson, Eric; Ranum, David; Kulp, Thomas J; Armstrong, Karla; Sommers, Ricky; McRae, Thomas G; Ritter, Karin; Siegell, Jeffrey H; Van Pelt, Doug; Smylie, Mike

    2007-07-01

    Fugitive emissions account for approximately 50% of total hydrocarbon emissions from process plants. Federal and state regulations aiming at controlling these emissions require refineries and petrochemical plants in the United States to implement a Leak Detection and Repair Program (LDAR). The current regulatory work practice, U.S. Environment Protection Agency Method 21, requires designated components to be monitored individually at regular intervals. The annual costs of these LDAR programs in a typical refinery can exceed US$1,000,000. Previous studies have shown that a majority of controllable fugitive emissions come from a very small fraction of components. The Smart LDAR program aims to find cost-effective methods to monitor and reduce emissions from these large leakers. Optical gas imaging has been identified as one such technology that can help achieve this objective. This paper discusses a refinery evaluation of an instrument based on backscatter absorption gas imaging technology. This portable camera allows an operator to scan components more quickly and image gas leaks in real time. During the evaluation, the instrument was able to identify leaking components that were the source of 97% of the total mass emissions from leaks detected. More than 27,000 components were monitored. This was achieved in far less time than it would have taken using Method 21. In addition, the instrument was able to find leaks from components that are not required to be monitored by the current LDAR regulations. The technology principles and the parameters that affect instrument performance are also discussed in the paper.

  17. Membrane Protein Stability Analyses by Means of Protein Energy Profiles in Case of Nephrogenic Diabetes Insipidus

    Directory of Open Access Journals (Sweden)

    Florian Heinke

    2012-01-01

    Full Text Available Diabetes insipidus (DI is a rare endocrine, inheritable disorder with low incidences in an estimated one per 25,000–30,000 live births. This disease is characterized by polyuria and compensatory polydypsia. The diverse underlying causes of DI can be central defects, in which no functional arginine vasopressin (AVP is released from the pituitary or can be a result of defects in the kidney (nephrogenic DI, NDI. NDI is a disorder in which patients are unable to concentrate their urine despite the presence of AVP. This antidiuretic hormone regulates the process of water reabsorption from the prourine that is formed in the kidney. It binds to its type-2 receptor (V2R in the kidney induces a cAMP-driven cascade, which leads to the insertion of aquaporin-2 water channels into the apical membrane. Mutations in the genes of V2R and aquaporin-2 often lead to NDI. We investigated a structure model of V2R in its bound and unbound state regarding protein stability using a novel protein energy profile approach. Furthermore, these techniques were applied to the wild-type and selected mutations of aquaporin-2. We show that our results correspond well to experimental water ux analysis, which confirms the applicability of our theoretical approach to equivalent problems.

  18. High temperature degradation in power plants and refineries

    Directory of Open Access Journals (Sweden)

    Furtado Heloisa Cunha

    2004-01-01

    Full Text Available Thermal power plants and refineries around the world share many of the same problems, namely aging equipment, high costs of replacement, and the need to produce more efficiently while being increasingly concerned with issues of safety and reliability. For equipment operating at high temperature, there are many different mechanisms of degradation, some of which interact, and the rate of accumulation of damage is not simple to predict. The paper discusses the mechanisms of degradation at high temperature and methods of assessment of such damage and of the remaining safe life for operation.

  19. Yearly refinery construction indexes listed for 68 years

    International Nuclear Information System (INIS)

    Farrar, G.

    1996-01-01

    Yearly values are presented for the Nelson-Farrar refinery inflation cost index since 1926. They are based on 1946 as 100, since that was the date of index inception. Values from 1926 to 1945 were back calculated. Data are presented on indexed cost of materials, labor, and miscellaneous equipment for 1926 through 1994. A second table of itemized refining cost indexes for the years 1954, 1972, 1992--1994, and the first eight months of 1995 is also presented. This table subdivides materials, labor, and equipment into component costs

  20. Capital vs. service contract at Conoco Humber Refinery

    International Nuclear Information System (INIS)

    Threlfall, Peter; Sperring, Simon

    1999-01-01

    The value of outsourcing for water treatment is illustrated through experience at the Conoco Humber refinery. A point was reached where the quality of water at the plant was so poor that demineralized water was brought to the site by tanker. The paper describes how and why it was decided to design, build, operate and maintain an outsourced system. It points out how the newer technologies can be environmentally friendly and, at the same time, reduce operating and maintenance costs, optimise manpower and cut management costs. (UK)

  1. Microbial enhanced separation of oil from a petroleum refinery sludge.

    Science.gov (United States)

    Joseph, P J; Joseph, Ammini

    2009-01-15

    Petroleum refineries around the world have adopted different technological options to manage the solid wastes generated during the refining process and stocking of crude oil. These include physical, chemical and biological treatment methods. In this investigation bacterial mediated oil separation is effected. Two strains of Bacillus were isolated from petroleum-contaminated soils, and inoculated into slurry of sludge, and sludge-sand combinations. The bacteria could effect the separation of oil so as to form a floating scum within 48h with an efficiency of 97% at < or =5% level of sludge in the sludge-sand mixture. The activity was traced to the production of biosurfactants by bacteria.

  2. 40 CFR 80.1280 - How are refinery benzene baselines calculated?

    Science.gov (United States)

    2010-07-01

    ... benzene). i = Individual batch of gasoline produced at the refinery from January 1, 2004 through December 31, 2005. n = Total number of batches of gasoline produced at the refinery from January 1, 2004... PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Gasoline Benzene Averaging, Banking and Trading...

  3. Sounding pollution and the refinery environmental risks; A poluicao sonora e os riscos ambientais das refinarias

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2005-07-01

    This chapter gives a general overview on the effects of the sound pollution, the principal pollutants emitted by the oil refineries, control actions for the sound waves emissions, the minimization actions, the risk concepts and evaluation, the risk perception and the accidents in refineries.

  4. Environmental nickel exposure from oil refinery emissions: a case study in Ecuador.

    Science.gov (United States)

    Harari, Raúl; Harari, Florencia; Forastiere, Francesco

    2016-01-01

    Nickel is a strong skin and respiratory sensitizer and a recognized carcinogen. Oil refineries are important sources of atmospheric emissions of toxic pollutants, including nickel. Populations residing close to oil refineries are at potential risk. The aim of this study was to evaluate the exposure to nickel in a population living close to the largest oil refinery in Ecuador, located in the city of Esmeraldas. We recruited 47 workers from the oil refinery as well as 195 students from 4 different schools close to the plant and 94 students from another school 25 km far from the industry. Urinary nickel concentrations were used to assess the exposure to nickel. Students from the school next to the oil refinery showed the highest urinary nickel concentrations while workers from the refinery showed the lowest concentrations. Median nickel concentrations were > 2µg/L in all study groups. The populations living close to the oil refineries are potentially exposed to nickel from atmospheric emissions. Further studies investigating nickel-related health effects in the population residing close to the refinery of Esmeralda are needed.

  5. 76 FR 64943 - Proposed Cercla Administrative Cost Recovery Settlement; ACM Smelter and Refinery Site, Located...

    Science.gov (United States)

    2011-10-19

    ... Settlement; ACM Smelter and Refinery Site, Located in Cascade County, MT AGENCY: Environmental Protection... projected future response costs concerning the ACM Smelter and Refinery NPL Site (Site), Operable Unit 1..., Helena, MT 59626. Mr. Sturn can be reached at (406) 457-5027. Comments should reference the ACM Smelter...

  6. Risk analysis of the sea desalination plant at the 5th refinery of south ...

    African Journals Online (AJOL)

    In this study, hazards in the desalination unit of a gas refinery in Asaluyeh, south of Iran was evaluated, using the PHA-PRO6 software, for which recommendations were made to avoid potential risks involved. Based on 8-years history of the refinery operation, maintenance records, accidents, safety vulnerabilities of the plant ...

  7. 40 CFR 73.90 - Allowance allocations for small diesel refineries.

    Science.gov (United States)

    2010-07-01

    ... refineries. 73.90 Section 73.90 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) SULFUR DIOXIDE ALLOWANCE SYSTEM Small Diesel Refineries § 73.90 Allowance allocations... application for certification, submitted to the address in § 73.13 of this chapter, shall include the...

  8. The Implementation and Maintenance of a Behavioral Safety Process in a Petroleum Refinery

    Science.gov (United States)

    Myers, Wanda V.; McSween, Terry E.; Medina, Rixio E.; Rost, Kristen; Alvero, Alicia M.

    2010-01-01

    A values-centered and team-based behavioral safety process was implemented in a petroleum oil refinery. Employee teams defined the refinery's safety values and related practices, which were used to guide the process design and implementation. The process included (a) a safety assessment; (b) the clarification of safety-related values and related…

  9. 76 FR 42052 - National Emission Standards for Hazardous Air Pollutants From Petroleum Refineries

    Science.gov (United States)

    2011-07-18

    ...-AO55 National Emission Standards for Hazardous Air Pollutants From Petroleum Refineries AGENCY... the National Emission Standards for Hazardous Air Pollutants From Petroleum Refineries. EPA is now... signed a final rule amending the National Emission Standards for Hazardous Air Pollutants From Petroleum...

  10. Effect of energy balance profiles on metabolic and reproductive response in Holstein and Swedish Red cows.

    Science.gov (United States)

    Ntallaris, T; Humblot, P; Båge, R; Sjunnesson, Y; Dupont, J; Berglund, B

    2017-03-01

    This study examined the effect of two feeding levels during the antepartum and postpartum period on reproductive performance and blood metabolites (glucose, non-esterified fatty acids (NEFA), insulin) in primiparous Holstein and Swedish Red (SRB) cows, in order to identify possible differences in the way these breeds respond to negative energy balance after calving. A total of 44 cows (22 Holstein, 22 SRB) kept in a loose housing system were included in the study. The control group (HE, n = 23) was fed a diet for high-producing cows (target 35 kg/d energycorrected milk, ECM). A lower feeding intensity (LE, n = 21) was achieved by giving -50% concentrate to target 25 kg/d ECM. Diets were implemented 30 days before expected calving and the cows were monitored for 120 days postpartum. Milk yield and composition, dry matter intake (DMI), live body weight and body condition score (BCS) were assessed to calculate the weekly energy balance (residual feed intake). Blood sampling started before diet implementation and was repeated every 2 weeks until Day 60 postpartum and then once monthly until Day 120. Plasma was kept at -20 °C until analysis for glucose, insulin and NEFA concentrations. Mixed linear models were used to analyse data (SAS 9.3; PROC MIXED). Holstein cows had lower mean energy balance than SRB cows (-4.7 ± 1.4 and -0.9 ± 1.4 MJ, respectively; p = 0.05). SRB cows had higher (pcows (2.7 ± 0.1) and also higher plasma glucose concentrations from Day -30 to Day 120 relative to parturition (4.1 ± 0.1 and 4.2 ± 0.1 log ; mg/100 ml, respectively; p cows than in Holsteins at Day -14 before calving, indicating higher mobilisation of lipid from adipose tissue already before calving. In contrast, Holstein cows had higher NEFA at Day 14 postpartum than SRB cows (p cows prioritise milk production to a larger extent than SRB cows, resulting in a less balanced metabolic profile. Copyright © 2016 Elsevier Inc. All rights reserved.

  11. Conservation and reuse of water in Brazilian petroleum refineries; Conservacao e reuso de agua em refinarias de petroleo no Brasil

    Energy Technology Data Exchange (ETDEWEB)

    Pombo, Felipe Ramalho; Magrini, Alessandra; Szklo, Alexandre Salem [Universidade Federal do Rio de Janeiro (PPE/COPPE/UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-Graduacao de Engenharia. Programa de Planejamento Energetico], Emails: frpombo@ppe.ufrj.br, ale@ppe.ufrj.br, szklo@ppe.ufrj.br

    2010-07-01

    This paper views to present the main technologies for effluent treatment of petroleum refineries having as target the reuse. An analysis of international and Brazilian experiences of water reuse in petroleum refineries is performed viewing to support the proposition of recommendations for Brazilian refineries.

  12. Characterizing exposures to airborne metals and nanoparticle emissions in a refinery.

    Science.gov (United States)

    Miller, Arthur; Drake, Pamela L; Hintz, Patrick; Habjan, Matt

    2010-07-01

    An air quality survey was conducted at a precious metals refinery in order to evaluate worker exposures to airborne metals and to provide detailed characterization of the aerosols. Two areas within the refinery were characterized: a furnace room and an electro-refining area. In line with standard survey practices, both personal and area air filter samples were collected on 37-mm filters and analyzed for metals by inductively coupled plasma-atomic emission spectroscopy. In addition to the standard sampling, measurements were conducted using other tools, designed to provide enhanced characterization of the workplace aerosols. The number concentration and number-weighted particle size distribution of airborne particles were measured with a fast mobility particle sizer (FMPS). Custom-designed software was used to correlate particle concentration data with spatial location data to generate contour maps of particle number concentrations in the work areas. Short-term samples were collected in areas of localized high concentrations and analyzed using transmission electron microscopy (TEM) and energy dispersive spectroscopy (EDS) to determine particle morphology and elemental chemistry. Analysis of filter samples indicated that all of the workers were exposed to levels of silver above the Occupational Safety and Health Administration permissible exposure limit of 0.01 mg m(-3) even though the localized ventilation was functioning. Measurements with the FMPS indicated that particle number concentrations near the furnace increased up to 1000-fold above the baseline during the pouring of molten metal. Spatial mapping revealed localized elevated particle concentrations near the furnaces and plumes of particles rising into the stairwells and traveling to the upper work areas. Results of TEM/EDS analyses confirmed the high number of nanoparticles measured by the FMPS and indicated the aerosols were rich in metals including silver, lead, antimony, selenium, and zinc. Results of

  13. Opportunities and challenges at the interface between petrochemicals and refinery. The OMV view

    Energy Technology Data Exchange (ETDEWEB)

    Lichtscheidl, J. [OMV Refining and Marketing GmbH, Vienna (Austria)

    2007-07-01

    OMV's refineries have been integrated into petrochemicals since the first steam cracker came on line in 1970. The refineries in Schwechat, Burghausen and Romania, especially Arpechim, have significant petrochemical capacities. In 1998 PCD was merged with Borealis, a leading producer of high grade polymers. OMV's initial 25% stake in Borealis increased to 36 in 2007. The last years have seen major investments in Schwechat and Burghausen: Schwechat's cracker was expanded by approximately 150 KTA to a nominal 500 KTA of ethylene. And in Burghausen the revamp of the cracker has been combined with a metathesis unit in order to feed a new 330 KTA polypropylene plant. The polymer market is still growing. However, the bulk of investments to increase capacity are located in the Middle East and in the Asia-Pacific region, predominately in China. As more and more products from these regions find their way to Europe, the European petrochemicals industry faces fierce competition. The response is restructuring: the creation of Arkema (Total), the takeover of BP's petrochemical assets by INEOS, the disposal of Shell-BASF subsidiary Basell to Haldia Petrochemical and Accent Industries, and the transfer of Statoil's interest in Borealis to IPIC and OMV. And most recently, Basell's acquisition of Lyondell. Compared with competitors in the Middle East and the Asia-Pacific region, producers in Europe are burdened with serious disadvantages: fairly old, small units and high costs of labor, energy and raw materials. There is no single solution. OMV, however, will continue to follow the strategies that have been successful so far: - Ever closer integration of refining and petrochemicals; - Capturing market opportunities for profitable growth; -Remaining market orientated. (orig.)

  14. Toward effective ecological risk-management of refinery corrective action

    International Nuclear Information System (INIS)

    Metzger, B.H.; Rury, P.M.; Turton, D.; Archibald, B.; Clark, J.; Cura, J.

    1995-01-01

    Cleanup of complex industrial sites, such as refineries, requires risk-based decision tools to ensure that environmentally protective remediation is consistent with current and future land use. However, conventional ecological risk assessment approaches are not well suited for complex industrial sites. Site risk assessments focus on hypothetical chemical risk assuming diverse and undisturbed ecosystems, rather than industrial and disturbed area conditions. In addition, they offer little guidance as to how to make timely and effective risk management decisions. An innovative methodology is proposed to assist industry and regulatory risk managers with rapid EcoRisk reconnaissance and cost-effective remedial decision-making at complex industrial sites. Phase 1 comprises a three-step risk screening of areas of ecological concern at the site, which integrates habitat quality characteristics and potential chemical hazards. It yields an ordering of areas as follows: areas of no significant risk; areas of potentially significant risk; and areas of likely significant risk. A decision rule is then applied to determine appropriate risk management action, including: no action; additional study; and remedial or management action. In Phase 2, additional study is conducted for areas that exhibit potentially significant risk so as to facilitate risk management. This methodology is currently being applied at the 1,300 acre, former Exxon Bayway Refinery in New Jersey

  15. Oil-refinery and automotive emissions of rare earth elements

    International Nuclear Information System (INIS)

    Kitto, M.E.; Gordon, G.E.; Anderson, D.L.; Olmez, I.

    1991-01-01

    The concentration pattern of rare-earth elements (REEs) in emissions from oil refineries and newer-model automobiles shows a distortion from the crustal abundance pattern. The REEs arise from the zeolite cracking catalysts used in petroleum refining and emission-control substrates used in automobile catalytic converters, respectively. Ten petroleum cracking catalysts from four countries and 12 catalytic converters from five automobile manufacturers were characterized for their REE content. The cracking catalysts are highly enriched in light REEs, whereas the automobile catalysts are enriched primarily in Ce. Incorporation of zeolite catalysts into refined oil provides new atmospheric elemental signatures for tracing emissions from refineries and oil-fired power plants on a regional scale. Though both have enhanced La/REE ratios, emissions from these two sources can be distinguished by their La/V ratios. Although REE demand by the petroleum industry has dropped considerably in recent years, automobile catalytic converters containing REEs are expected to increase dramatically as more stringent emission regulations are adopted in Europe, Japan and the US

  16. Biodegradation of oil refinery wastes under OPA and CERCLA

    International Nuclear Information System (INIS)

    Banipal, B.S.; Myers, J.M.; Fisher, C.W.

    1995-01-01

    Land treatment of oil refinery wastes has been used as a disposal method for decades. More recently, numerous laboratory studies have been performed attempting to quantify degradation rates of more toxic polycyclic aromatic hydrocarbon compounds (PAHs). This paper discusses the results of the full-scale aerobic biodegradation operations using land treatment at the Macmillan Ring-Free Oil refining facility. The tiered feasibility approach in the evaluation of using biodegradation as a treatment method to achieve site-specific clean-up including pilot scale biodegradation operations is included in an earlier paper. Analytical results of biodegradation indicate that degradation rates observed in the laboratory can be met and exceeded under field conditions and that the site-specific cleanup criteria can be attained within a proposed project time. Also presented are degradation rates and half-lives for PAHs for which cleanup criteria has been established. PAH degradation rates and half-life values are determined and compared with the laboratory degradation rates and half-life values which used similar oil refinery wastes by other investigators (API 1987)

  17. Application of Ozone MBBR Process in Refinery Wastewater Treatment

    Science.gov (United States)

    Lin, Wang

    2018-01-01

    Moving Bed Biofilm Reactor (MBBR) is a kind of sewage treatment technology based on fluidized bed. At the same time, it can also be regarded as an efficient new reactor between active sludge method and the biological membrane method. The application of ozone MBBR process in refinery wastewater treatment is mainly studied. The key point is to design the ozone +MBBR combined process based on MBBR process. The ozone +MBBR process is used to analyze the treatment of concentrated water COD discharged from the refinery wastewater treatment plant. The experimental results show that the average removal rate of COD is 46.0%~67.3% in the treatment of reverse osmosis concentrated water by ozone MBBR process, and the effluent can meet the relevant standard requirements. Compared with the traditional process, the ozone MBBR process is more flexible. The investment of this process is mainly ozone generator, blower and so on. The prices of these items are relatively inexpensive, and these costs can be offset by the excess investment in traditional activated sludge processes. At the same time, ozone MBBR process has obvious advantages in water quality, stability and other aspects.

  18. Improving secondary clarifier performance at the Oakville Oil Refinery

    International Nuclear Information System (INIS)

    Edwards, S.M.; Bagley, D.M.

    2002-01-01

    The purpose of this study was threefold: to investigate the relationship between settleability and the physical properties of activated sludge, to correlate settleability and key operational parameters such as chemical oxygen demand (COD) concentration at the aeration basin inlet and to determine potential operational improvements to the Oakville Oil Refinery Wastewater Treatment Plant. Nine separate sets of stirred sludge-settling tests were conducted over a six-month period to measure settleability. The stirred sludge volume index (SSVI), the zone settling constants, and the Zheng-Bagley compression constants were determined. State point analyses were conducted to determine the maximum solids flux of the clarifiers. The concentrations of Al, Mn, Mg, Fe, Ca, Na, and K were determined to identify potential correlations to settling characteristics. Extracellular polymeric substances were extracted from the sludge and analyzed for the same reason. The performance of the clarifiers was highly variable during the period examined. As the refinery process flows and effluent streams changed, influent COD increased, from an average of 180mg/L to 600mg/L. Concurrently the settleability of the sludge decreased from excellent (SSVI = 68mL/g) to very poor (150mL/g), perhaps as the result of under aeration. State point analyses indicated that the clarifiers are under-sized for process upsets of this magnitude. (author)

  19. Improving secondary clarifier performance at the Oakville Oil Refinery

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, S.M.; Bagley, D.M. [Univ. of Toronto, Dept. of Civil Engineering, Toronto, Ontario (Canada)

    2002-06-15

    The purpose of this study was threefold: to investigate the relationship between settleability and the physical properties of activated sludge, to correlate settleability and key operational parameters such as chemical oxygen demand (COD) concentration at the aeration basin inlet and to determine potential operational improvements to the Oakville Oil Refinery Wastewater Treatment Plant. Nine separate sets of stirred sludge-settling tests were conducted over a six-month period to measure settleability. The stirred sludge volume index (SSVI), the zone settling constants, and the Zheng-Bagley compression constants were determined. State point analyses were conducted to determine the maximum solids flux of the clarifiers. The concentrations of Al, Mn, Mg, Fe, Ca, Na, and K were determined to identify potential correlations to settling characteristics. Extracellular polymeric substances were extracted from the sludge and analyzed for the same reason. The performance of the clarifiers was highly variable during the period examined. As the refinery process flows and effluent streams changed, influent COD increased, from an average of 180mg/L to 600mg/L. Concurrently the settleability of the sludge decreased from excellent (SSVI = 68mL/g) to very poor (150mL/g), perhaps as the result of under aeration. State point analyses indicated that the clarifiers are under-sized for process upsets of this magnitude. (author)

  20. Cathodic Protection Design Algorithms for Refineries Aboveground Storage Tanks

    Directory of Open Access Journals (Sweden)

    Kosay Abdul sattar Majbor

    2017-12-01

    Full Text Available Storage tanks condition and integrity is maintained by joint application of coating and cathodic protection. Iraq southern region rich in oil and petroleum product refineries need and use plenty of aboveground storage tanks. Iraq went through conflicts over the past thirty five years resulting in holding the oil industry infrastructure behind regarding maintenance and modernization. The primary concern in this work is the design and implementation of cathodic protection systems for the aboveground storage tanks farm in the oil industry. Storage tank external base area and tank internal surface area are to be protected against corrosion using impressed current and sacrificial anode cathodic protection systems. Interactive versatile computer programs are developed to provide the necessary system parameters data including the anode requirements, composition, rating, configuration, etc. Microsoft-Excel datasheet and Visual Basic.Net developed software were used throughout the study in the design of both cathodic protection systems. The case study considered in this work is the eleven aboveground storage tanks farm situated in al-Shauiba refinery in southern IRAQ. The designed cathodic protection systems are to be installed and monitored realistically in the near future. Both systems were designed for a life span of (15-30 years, and all their parameters were within the internationally accepted standards.

  1. Biodegradation of oil refinery wastes under OPA and CERCLA

    Energy Technology Data Exchange (ETDEWEB)

    Gamblin, W.W.; Banipal, B.S.; Myers, J.M. [Ecology and Environment, Inc., Dallas, TX (United States)] [and others

    1995-12-31

    Land treatment of oil refinery wastes has been used as a disposal method for decades. More recently, numerous laboratory studies have been performed attempting to quantify degradation rates of more toxic polycyclic aromatic hydrocarbon compounds (PAHs). This paper discusses the results of the fullscale aerobic biodegradation operations using land treatment at the Macmillan Ring-Free Oil refining facility. The tiered feasibility approach of evaluating biodegradation as a treatment method to achieve site-specific cleanup criteria, including pilot biodegradation operations, is discussed in an earlier paper. Analytical results of biodegradation indicate that degradation rates observed in the laboratory can be met and exceeded under field conditions and that site-specific cleanup criteria can be attained within a proposed project time. Also prevented are degradation rates and half-lives for PAHs for which cleanup criteria have been established. PAH degradation rates and half-life values are determined and compared with the laboratory degradation rates and half-life values which used similar oil refinery wastes by other in investigators (API 1987).

  2. Elemental profiling of laser cladded multilayer coatings by laser induced breakdown spectroscopy and energy dispersive X-ray spectroscopy

    Science.gov (United States)

    Lednev, V. N.; Sdvizhenskii, P. A.; Filippov, M. N.; Grishin, M. Ya.; Filichkina, V. A.; Stavertiy, A. Ya.; Tretyakov, R. S.; Bunkin, A. F.; Pershin, S. M.

    2017-09-01

    Multilayer tungsten carbide wear resistant coatings were analyzed by laser induced breakdown spectroscopy (LIBS) and energy dispersive X-ray (EDX) spectroscopy. Coaxial laser cladding technique was utilized to produce tungsten carbide coating deposited on low alloy steel substrate with additional inconel 625 interlayer. EDX and LIBS techniques were used for elemental profiling of major components (Ni, W, C, Fe, etc.) in the coating. A good correlation between EDX and LIBS data was observed while LIBS provided additional information on light element distribution (carbon). A non-uniform distribution of tungsten carbide grains along coating depth was detected by both LIBS and EDX. In contrast, horizontal elemental profiling showed a uniform tungsten carbide particles distribution. Depth elemental profiling by layer-by-layer LIBS analysis was demonstrated to be an effective method for studying tungsten carbide grains distribution in wear resistant coating without any sample preparation.

  3. Intermixing in heteroepitaxial islands: fast, self-consistent calculation of the concentration profile minimizing the elastic energy

    International Nuclear Information System (INIS)

    Gatti, R; UhlIk, F; Montalenti, F

    2008-01-01

    We present a novel computational method for finding the concentration profile which minimizes the elastic energy stored in heteroepitaxial islands. Based on a suitable combination of continuum elasticity theory and configurational Monte Carlo, we show that such profiles can be readily found by a simple, yet fully self-consistent, iterative procedure. We apply the method to SiGe/Si islands, considering realistic three-dimensional shapes (pyramids, domes and barns), finding strongly non-uniform distributions of Si and Ge atoms, in qualitative agreement with several experiments. Moreover, our simulated selective-etching profiles display, in some cases, a remarkable resemblance to the experimental ones, opening intriguing questions on the interplay between kinetic, entropic and elastic effects

  4. Measurements of the Energy Deposition Profile for 238U Ions with Energy 500 and 950 MEV/U in Stainless Steel and Copper Targets

    CERN Document Server

    Mustafin, Edil; Gnutov, A; Golubev, Alexander; Hofmann, Ingo; Kantsyrev, Alexei; Kunin, Andrey; Latysheva, Ludmila N; Luckjashin, Victor; Panova, Yulia; Schardt, Dieter; Sobolevskiy, Nikolai; Vatulin, Vladimir; Weyrich, Karin

    2005-01-01

    Sub-millimeter wall thickness is foreseen for the vacuum tubes in the magnets of the superconducting dipoles of the SIS100 and SIS300 of the FAIR Project. The Bragg peak of the energy deposition by the U ions in these walls may lie dangerously close to the superconducting cables. Thus the precise knowledge of the dE/dx profile is essential for estimating the heat load by the lost ions in the vicinity of the superconducting wires. Here we present the results of the measurement of the U ion beam energy deposition profile in Cu and stainless steel targets and compare the measured data with the Monte-Carlo simulation using the SHIELD code.

  5. Fuzzy-based Prioritization of Health, Safety, and Environmental Risks: The Case of a Large Gas Refinery

    Directory of Open Access Journals (Sweden)

    Auob Mirsaeidi

    2017-01-01

    Full Text Available The main objective of this study was to develop a fuzzy–based framework for the prioritization of health, safety and environment related risks posed against employees, working conditions, and process equipment in large gas refineries. The First Refinery at Pars Special Economic Energy Zone in South of Iran was taken as a case study. For this purpose, health, safety and environment related risks were determined based on the three criteria of impact severity, occurrence probability, and detect-ability using a questionnaire of 33 identified failures. The values obtained were processed by a so-called ‘contribution coefficient’. The results were then subjected to fuzzification and fuzzy rules were defined to calculate the risk level indices as the model outputs, which was then employed to facilitate the management decision-making process by prioritizing the management options. The prioritization values were then classified in six categories in the order of risk severity. Results revealed that failure in a combustion furnace had the highest rank while failure in the slug catcher ranked the lowest among the risk sources. It was also found that about 0.4% of the identified risks prioritized as “intolerable”, 79% as “major”, 20% as “tolerable”, and 0.7% as “minor”. Thus, most of the risks (more than 79% associated with the refinery has the potential of significant risks. The results indicated that the risk of the pollutant emissions from the combustion furnaces is the highest. Exposures to harmful physical, chemical, psychological, and ergonomic substances are the other risks, respectively.

  6. Production of high energy, uniform focal profiles with the Nike laser

    Science.gov (United States)

    Lehecka, T.; Lehmberg, R. H.; Deniz, A. V.; Gerber, K. A.; Obenschain, S. P.; Pawley, C. J.; Pronko, M. S.; Sullivan, C. A.

    1995-02-01

    Nike, a KrF laser facility at the Naval Research Laboratory, is designed to produce high intensity, ultra-uniform focal profiles for experiments relating to direct drive inertial confinement fusion. We present measurements of focal profiles through the next-to-last amplifier, a 20 × 20 cm 2 aperture electron beam pumped amplifier capable of producing more than 120 J of output in a 120 ns pulse. Using echelon free induced spatial incoherence beam smoothing this system has produced focal profiles with less than 2% tilt and curvature and less than 2% rms variation from a flat top distribution.

  7. Patterns of energy use in the Brazilian economy: Can the profile of Brazilian exports determine the future energy efficiency of its industry?

    International Nuclear Information System (INIS)

    Machado, G.V.; Schaeffer, R.

    1997-01-01

    This study examines the integration of the Brazilian economy in the global economy as a determining factor for the energy efficiency of its industry. Depending upon the profile of a country's exports (i.e., depending upon the share of energy-intensive exports out of total exports), different quantities of energy are required to produce the country's exported goods, which may counterbalance efforts made elsewhere to improve the overall energy efficiency of the country's industry. Different scenarios for the energy embodied in the industrial exports of Brazil are considered for the period 1995--2015. These scenarios are a combination of different shares of energy-intensive goods in the total exports of the country with different assumptions for gains obtained in industrial energy efficiency over time. For all scenarios the same fundamental hypothesis of liberalization of commerce and economic growth are assumed. Results for the year 2015 show that the total energy embodied in industrial exports varies from 1,413 PJ to 2,491 PJ, and the total industrial use of energy varies from 3,858 PJ to 6,153 PJ, depending upon the assumptions made. This is equivalent to an average industrial energy intensity variation ranging from 13.8 MJ to 22.0 MJ per US$-1985. The authors conclude that any policy aimed at improving Brazil's overall industrial energy efficiency should concentrate not only on the reduction of the energy intensity of particular industrial sectors, but also (and, perhaps, more importantly) on rethinking the very strategy for the integration of the country's economy in the global market in the future, with respect to the share of energy-intensive goods out of total exports. The focus is not incidental, for the ongoing structural changes in Brazilian exports alone may come to offset any efficiency improvements achieved by the national industry as a whole

  8. Generation of dual-wavelength, synchronized, tunable, high energy, femtosecond laser pulses with nearly perfect gaussian spatial profile

    Science.gov (United States)

    Wang, J.-K.; Siegal, Y.; Lü, C.; Mazur, E.

    1992-07-01

    We use self-phase modulation in a single-mode fiber to produce broadband femtosecond laser pulses. Subsequent amplification through two Bethune cells yields high-energy, tunable, pulses synchronized with the output of an amplified colliding-pulse-modelocked (CPM) laser. We routinely obtain tunable 200 μJ pulses of 42 fs (fwhm) duration with a nearly perfect gaussian spatial profile. Although self-phase modulation in a single-mode fiber is widely used in femtosecond laser systems, amplification of a fiber-generated supercontinuum in a Bethune cell amplifier is a new feature which maintains the high-quality spatial profile while providing high gain. This laser system is particularly well suited for high energy dual-wavelength pump=probe experiments and time-resolved four-wave mixing spectroscopy.

  9. Exploring the binding energy profiles of full agonists, partial agonists, and antagonists of the α7 nicotinic acetylcholine receptor.

    Science.gov (United States)

    Tabassum, Nargis; Ma, Qianyun; Wu, Guanzhao; Jiang, Tao; Yu, Rilei

    2017-09-01

    Nicotinic acetylcholine receptors (nAChRs) belong to the Cys-loop receptor family and are important drug targets for the treatment of neurological diseases. However, the precise determinants of the binding efficacies of ligands for these receptors are unclear. Therefore, in this study, the binding energy profiles of various ligands (full agonists, partial agonists, and antagonists) were quantified by docking those ligands with structural ensembles of the α7 nAChR exhibiting different degrees of C-loop closure. This approximate treatment of interactions suggested that full agonists, partial agonists, and antagonists of the α7 nAChR possess distinctive binding energy profiles. Results from docking revealed that ligand binding efficacy may be related to the capacity of the ligand to stabilize conformational states with a closed C loop.

  10. Combined analysis of job and task benzene air exposures among workers at four US refinery operations.

    Science.gov (United States)

    Burns, Amanda; Shin, Jennifer Mi; Unice, Ken M; Gaffney, Shannon H; Kreider, Marisa L; Gelatt, Richard H; Panko, Julie M

    2017-03-01

    Workplace air samples analyzed for benzene at four US refineries from 1976 to 2007 were pooled into a single dataset to characterize similarities and differences between job titles, tasks and refineries, and to provide a robust dataset for exposure reconstruction. Approximately 12,000 non-task (>180 min) personal samples associated with 50 job titles and 4000 task (job titles and task codes across all four refineries, and (5) our analysis of variance (ANOVA) of the distribution of benzene air concentrations for select jobs/tasks across all four refineries. The jobs and tasks most frequently sampled included those with highest potential contact with refinery product streams containing benzene, which reflected the targeted sampling approach utilized by the facility industrial hygienists. Task and non-task data were analyzed to identify and account for significant differences within job-area, task-job, and task-area categories. This analysis demonstrated that in general, areas with benzene containing process streams were associated with greater benzene air concentrations compared to areas with process streams containing little to no benzene. For several job titles and tasks analyzed, there was a statistically significant decrease in benzene air concentration after 1990. This study provides a job and task-focused analysis of occupational exposure to benzene during refinery operations, and it should be useful for reconstructing refinery workers' exposures to benzene over the past 30 years.

  11. 'Feasibility study for joint implementation, etc.' on modernization project at Sisak and Rijeka Refineries of Industrija Nafte d.d. in Croatia

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of strengthening the international competitive force in the oil industry of Croatia and reducing greenhouse effect gas by introducing energy conservation technology, study was made of the rehabilitation of oil refineries (Rijeka and Sisak) of Croatia's oil corporation, INDUSTRIJA NAFTE d.d. (INA). Rijeka and Sisak Refineries have the oil processing capacity of 6 million t/y and 4.6 million t/y, respectively, but they were constructed during the 1960s-1970s and are now superannuated. In this project, the following are adopted: heightening of the temperature of raw material supply, surging avoidance control, reutilization of condensate water of vacuum distillation, heightening of MEA concentration, control of excess air ratio in heating furnace, preheating of combustion air in heating furnace, application of small-diameter pump impeller, the optimum control of steam/electric system, heightening of temperature of cleaning water of desalting device, stop of adoption of flare seal gas, etc. The energy conservation effect to be expected from the project is 43,065 toe/y in a total of the two refineries, and the reduction in greenhouse effect gas is 133,000 t-CO2/y. Further, the internal return rate is 53.12%, which is very attractive for INA. (NEDO)

  12. Mammary gene expression profiles during an intramammary challenge reveal potential mechanisms linking negative energy balance with impaired immune response

    DEFF Research Database (Denmark)

    Moyes, Kasey; Drackley, J K; Morin, D E

    2010-01-01

    Our objective was to compare mammary tissue gene expression profiles during a Streptococcus uberis (S. uberis) mastitis challenge between lactating cows subjected to dietary-induced negative energy balance (NEB; n = 5) and cows fed ad libitum to maintain positive energy balance (PEB; n = 5...... 0.05), with 86 DEG up-regulated and 201 DEG down-regulated. Canonical pathways most affected by NEB were IL-8 Signaling (10 genes), Glucocorticoid Receptor Signaling (13), and NRF2-mediated Oxidative Stress Response (10). Among genes differentially expressed by NEB, Cell Growth and Proliferation (48...

  13. The energy and identification continua of burnout and work engagement: Developmental profiles over eight years

    Directory of Open Access Journals (Sweden)

    Anne Mäkikangas

    2017-06-01

    Full Text Available Understanding of the mutual developmental dynamics between burnout and work engagement is limited due to the lack of longitudinal studies with long follow-ups and multi-wave data. This study sought to identify subgroups of employees characterized by long-term exhaustion-vigor (energy continuum and cynicism-dedication (identification continuum. A further important aim was to investigate differences between the identified subgroups in their experiences of progress in their personal work goals. Five-wave, eight-year follow-up data among Finnish white-collar professionals (n = 168 were studied using Latent Profile Analysis (LPA. The analysis yielded three exhaustion-vigor subgroups: 1 “Low stable exhaustion – high stable vigor” (n = 141, 2 “Fluctuating exhaustion and vigor” (n = 19, and 3 “Stable average exhaustion – decreasing vigor” (n = 8. Three subgroups were also found for cynicism-dedication: 1 “Low stable cynicism – high stable dedication” (n = 124, 2 “Increasing cynicism – decreasing dedication” (n = 27, and 3 “Decreasing cynicism – increasing dedication” (n = 17. Exhaustion and vigor were found to be stable and mutually exclusive experiences for the great majority of the participants. However, mean changes were also detected – especially in vigor – but these were rare. A notable finding was that the levels of and changes in cynicism and dedication showed opposite trends in each subgroup: among the majority of the participants (74%, the levels of cynicism and dedication were stable and inversely related, while among one-third their levels simultaneously changed in the reverse direction. The most successful progress in personal work goals was found in the groups described by the identification continuum, i.e., in the groups of “Low stable cynicism – high stable dedication” and “Decreasing cynicism – increasing dedication”.

  14. 1170-MW(t) HTGR-PS/C plant application study report: Geismar, Louisiana refinery/chemical complex application

    International Nuclear Information System (INIS)

    McMain, A.T. Jr.; Stanley, J.D.

    1981-05-01

    This report summarizes a study to apply an 1170-MW(t) high-temperature gas-cooled reactor - process steam/cogeneration (HTGR-PS/C) to an industrial complex at Geismar, Louisiana. This study compares the HTGR with coal and oil as process plant fuels. This study uses a previous broad energy alternative study by the Stone and Webster Corporation on refinery and chemical plant needs in the Gulf States Utilities service area. The HTGR-PS/C was developed by General Atomic (GA) specifically for industries which require both steam and electric energy. The GA 1170-MW(t) HTGR-PC/C design is particularly well suited to industrial applications and is expected to have excellent cost benefits over other energy sources

  15. Comparative study of Fischer–Tropsch production and post-combustion CO2 capture at an oil refinery: Economic evaluation and GHG (greenhouse gas emissions) balances

    International Nuclear Information System (INIS)

    Johansson, Daniella; Franck, Per-Åke; Pettersson, Karin; Berntsson, Thore

    2013-01-01

    The impact on CO 2 emissions of integrating new technologies (a biomass-to-Fischer–Tropsch fuel plant and a post-combustion CO 2 capture plant) with a complex refinery has previously been investigated separately by the authors. In the present study these designs are integrated with a refinery and evaluated from the point-of-view of economics and GHG (greenhouse gas emissions) emissions and are compared to a reference refinery. Stand-alone Fischer–Tropsch fuel production is included for comparison. To account for uncertainties in the future energy market, the assessment has been conducted for different future energy market conditions. For the post-combustion CO 2 capture process to be profitable, the present study stresses the importance of a high charge for CO 2 emission. A policy support for biofuels is essential for the biomass-to-Fischer–Tropsch fuel production to be profitable. The level of the support, however, differs depending on scenario. In general, a high charge for CO 2 economically favours Fischer–Tropsch fuel production, while a low charge for CO 2 economically favours Fischer–Tropsch fuel production. Integrated Fischer–Tropsch fuel production is most profitable in scenarios with a low wood fuel price. The stand-alone alternative shows no profitability in any of the studied scenarios. Moreover, the high investment costs make all the studied cases sensitive to variations in capital costs. - Highlights: • Comparison of Fischer–Tropsch (FT) fuel production and CO 2 capture at a refinery. • Subsidies for renewable fuels are essential for FT fuel production to be profitable. • A high charge for CO 2 is essential for post-combustion CO 2 capture to be profitable. • A low charge for CO 2 economically favours FT fuel production. • Of the studied cases, CO 2 capture shows the greatest reduction in GHG emissions

  16. Investments in the Dutch onshore wind energy industry: A review of investor profiles and the impact of renewable energy subsidies

    NARCIS (Netherlands)

    Niesten, Eva; Jolink, Albert; Chappin, Maryse

    The 2020 renewable energy targets have stimulated the debate on the efficacy of policy schemes. Discussion on the efficacy of these schemes has largely been on the growth in the share of renewable energy, and less on the alignment of policies to the needs of investors. However, research in this

  17. Corrosion resistance of high performance stainless steels in cooling water and other refinery environments

    International Nuclear Information System (INIS)

    Kovach, C.W.; Redmerski, L.S.

    1984-01-01

    The recent successful introduction of high performance stainless steels as tubing for seawater cooled electric utility condensers suggests that these alloys can also provide useful service in refinery heat exchanger applications. Since many of these applications involve higher temperature exposure than steam condensers, a study was conducted to evaluate crevice corrsion resistance over a range of cooling water temperature and chloride concentrations, and also to evaluate general corrosion resistance in some strong chemical and refinery environments. These stainless steels display excellent crevice corrosion resistance as well as good resistance to a variety of chemical environments that may be encountered in refinery, petrochemical and chemical plant service

  18. Multi objective multi refinery optimization with environmental and catastrophic failure effects objectives

    Science.gov (United States)

    Khogeer, Ahmed Sirag

    2005-11-01

    Petroleum refining is a capital-intensive business. With stringent environmental regulations on the processing industry and declining refining margins, political instability, increased risk of war and terrorist attacks in which refineries and fuel transportation grids may be targeted, higher pressures are exerted on refiners to optimize performance and find the best combination of feed and processes to produce salable products that meet stricter product specifications, while at the same time meeting refinery supply commitments and of course making profit. This is done through multi objective optimization. For corporate refining companies and at the national level, Intea-Refinery and Inter-Refinery optimization is the second step in optimizing the operation of the whole refining chain as a single system. Most refinery-wide optimization methods do not cover multiple objectives such as minimizing environmental impact, avoiding catastrophic failures, or enhancing product spec upgrade effects. This work starts by carrying out a refinery-wide, single objective optimization, and then moves to multi objective-single refinery optimization. The last step is multi objective-multi refinery optimization, the objectives of which are analysis of the effects of economic, environmental, product spec, strategic, and catastrophic failure. Simulation runs were carried out using both MATLAB and ASPEN PIMS utilizing nonlinear techniques to solve the optimization problem. The results addressed the need to debottleneck some refineries or transportation media in order to meet the demand for essential products under partial or total failure scenarios. They also addressed how importing some high spec products can help recover some of the losses and what is needed in order to accomplish this. In addition, the results showed nonlinear relations among local and global objectives for some refineries. The results demonstrate that refineries can have a local multi objective optimum that does not

  19. Aerobic degradation of petroleum refinery wastewater in sequential batch reactor.

    Science.gov (United States)

    Thakur, Chandrakant; Srivastava, Vimal C; Mall, Indra D

    2014-01-01

    The aim of the present work was to study the effect of various parameters affecting the treatment of raw petroleum refinery wastewater (PRW) having chemical oxygen demand (COD) of 350 mg L(-1) and total organic carbon (TOC) of 70 mg L(-1) in sequential batch reactor (SBR). Effect of hydraulic retention time (HRT) was studied in instantaneous fill condition. Maximum COD and TOC removal efficiencies were found to be 80% and 84%, respectively, for fill phase of 2 h and react phase of 2 h with fraction of SBR being filled with raw PRW in each cycle being 0.4. Effect of parameters was studied in terms of settling characteristic of treated slurry. Kinetics of treatment process has been studied. FTIR and UV-visible analysis of PRW before and after treatment have been performed so as to understand the degradation mechanism.

  20. Phenol oxidation of petrol refinery wastewater catalyzed by Laccase

    International Nuclear Information System (INIS)

    Vargas, Maria Carolina; Ramirez, Nubia E.

    2002-01-01

    Laccase has been obtained through two different production systems, the first using Pleurotus ostreatus in solid-state fermentation, the second one using Trametes versicolor in submerged culture. Different substrates (by products from yeast, flour and beverage industries) have been evaluated in both systems. Maximum laccase yield with Pleurotus ostreatus (25 u/ml) was obtained in a wheat bran medium. The maximum enzyme concentration level using Trametes versicolor (25 u/ml) was achieved in a submerged system, containing 10% vinasse, 4,5% wheat bran and 0,2% molasses per liter of waste. Culture filtrate extracted from Pleurotus ostreatus was used to remove phenol from wastewater. The enzymatic treatment is effective over a wide pH and temperature range. The Laccase treatment has been successfully used to dephenolize industrial petrol refinery wastewater. The advantage of Laccase dephenolization is that this enzyme uses molecular oxygen as an oxidant

  1. Cleaning up gasoline will increase refinery hydrogen demand

    International Nuclear Information System (INIS)

    Pretorius, E.B.; Muan, A.

    1992-01-01

    This paper reports that hydrogen needs will increase two to five times as the world turns its attention to cleaning up engine exhaust. The subject of fuel trends and hydrogen needs at Foster Wheeler USA Corp.'s Hydrogen Plant Conference, June 2--4, in Orlando was addressed. The conference was attended by more than 100 people from 12 different countries. Drawing on knowledge from over 1 billion scfd of total installed hydrogen plant capacity, Foster Wheeler experts presented papers in the fields of steam reforming, partial oxidation (with all feedstocks, from natural gas to resids and coal), and steam reformer design. Other industry specialists gave papers on refinery balances, markets, coal feedstocks, utility systems, and components for hydrogen plants

  2. Energy and greenhouse gas profile of the Nouvelle Aquitaine region. Release 2017

    International Nuclear Information System (INIS)

    Rousset, Alain; Poitevin, Lionel; Loeb, Amandine; Philippot, Herve; Rebouillat, Lea; Jacquelin, Antoine

    2017-06-01

    This publication first proposes graphs and comments characterising final energy consumption of the Nouvelle Aquitaine region: regional situation in 2015 (analysis per sector and per energy), primary resources, social-economic analysis (energy bill, level of energy poverty, burden due to old housing and commuting for households), evolution of energy consumption between 2005 and 2015 (per sector, per source of energy, evolution of energy intensity and of the energy bill). The next part addresses greenhouse gas emissions: regional situation in 2015 (distribution in terms of emission type and per gas), evolutions between 1990 and 2015, evolutions per sector. The third part addresses renewable energies: regional situation for the different types of renewable energy, comparison with final energy consumption, comparison with national data, production evolutions, focus per sector (wood and wood by-products, heat pumps in the housing sector, urban waste valorisation units, biogas valorisation, bio-fuels, wind energy, hydroelectricity, solar photovoltaic). The last part recalls national objectives related to energy, to greenhouse gas emissions for France and for the region, in relationship with the law on energy transition and for a green growth

  3. BTEX biodegradation by bacteria from effluents of petroleum refinery.

    Science.gov (United States)

    Mazzeo, Dânia Elisa Christofoletti; Levy, Carlos Emílio; de Angelis, Dejanira de Franceschi; Marin-Morales, Maria Aparecida

    2010-09-15

    Groundwater contamination with benzene, toluene, ethylbenzene and xylene (BTEX) has been increasing, thus requiring an urgent development of methodologies that are able to remove or minimize the damages these compounds can cause to the environment. The biodegradation process using microorganisms has been regarded as an efficient technology to treat places contaminated with hydrocarbons, since they are able to biotransform and/or biodegrade target pollutants. To prove the efficiency of this process, besides chemical analysis, the use of biological assessments has been indicated. This work identified and selected BTEX-biodegrading microorganisms present in effluents from petroleum refinery, and evaluated the efficiency of microorganism biodegradation process for reducing genotoxic and mutagenic BTEX damage through two test-systems: Allium cepa and hepatoma tissue culture (HTC) cells. Five different non-biodegraded BTEX concentrations were evaluated in relation to biodegraded concentrations. The biodegradation process was performed in a BOD Trak Apparatus (HACH) for 20 days, using microorganisms pre-selected through enrichment. Although the biodegradation usually occurs by a consortium of different microorganisms, the consortium in this study was composed exclusively of five bacteria species and the bacteria Pseudomonas putida was held responsible for the BTEX biodegradation. The chemical analyses showed that BTEX was reduced in the biodegraded concentrations. The results obtained with genotoxicity assays, carried out with both A. cepa and HTC cells, showed that the biodegradation process was able to decrease the genotoxic damages of BTEX. By mutagenic tests, we observed a decrease in damage only to the A. cepa organism. Although no decrease in mutagenicity was observed for HTC cells, no increase of this effect after the biodegradation process was observed either. The application of pre-selected bacteria in biodegradation processes can represent a reliable and

  4. Solid waste management : a case study of National Refinery Limited

    Energy Technology Data Exchange (ETDEWEB)

    Syed, A.H.; Syed, Z.R. [National Refinery Ltd., Karachi (Pakistan); NED Univ. of Engineering and Technology, Karachi (Pakistan)

    2000-07-01

    A study was conducted to quantify and classify the waste generated at the National Refinery Limited (NRL). This refinery, located in Karachi, Pakistan, produces naphtha, motor gasoline, diesel, kerosene and lubricating oils and much more. Various units such as crude oil storage, thermal cracking, catalytic cracking and others were surveyed to assess the source and nature of the pollution. It was found that the major contributor to air pollution was the sulfur released through the burning of fuel oil during day-to-day operations. It was determined that approximately 2000 metric tons of solid waste were produced each day, along with 0.55 million gallons of waste water. In addition, sulfur, carbon dioxide, carbon monoxide and nitrogen dioxide were also released in the atmosphere. The solid waste was composed of municipal waste, sludges from the API and other discarded materials. The authors then proceeded to determine the heavy metals contents in samples obtained from combined sludge dumping areas on the premises. The sludges contained sulfur (0-1.26 wt per cent), lead (0-0.156 wt per cent), iron (0.01-3.4 wt per cent), chromium (0-0.159 per cent), copper (0-0.05 wt per cent), cadmium (0-0.0034 wt per cent), nickel (0-0.168 wt per cent), and manganese (0.0015-0.0776 wt per cent). It was recommended that hazardous and non-hazardous wastes be segregated, that a separate feasibility study be undertaken to determine the best possible course of action to dispose of solid waste, and that government guidelines be established on the same topic. 5 refs., 4 tabs.

  5. The share of renewable energy in the EU. Country Profiles. Overview of Renewable Energy Sources in the Enlarged European Union

    International Nuclear Information System (INIS)

    2004-01-01

    The promotion of renewable energy has an important role to play in addressing the growing dependence on energy imports in Europe and in tackling climate change. Since 1997, the Union has been working towards the ambitious target of a 12% share of renewable energy in gross inland consumption by 2010. In 1997, the share of renewable energy was 5.4%; by 2001 it had reached 6%. This Staff Working Document gives an overview of the different situations of renewable energy sources in the European Union. It includes part of the formal report that the Commission is required to make under Article 3 of Directive 2001/77/EC on electricity from renewable energy sources, and it completes the overall picture with information at a country level on the heat produced from renewable energies and biofuels in the transport sector. This Staff Working Document complements the Communication on 'The share of Renewable Energy sources in the EU'. Data is based on different sources. Firstly, on the reports from Member States on national progress in achieving the targets on electricity from renewable energy sources. Secondly, on a study launched by the Commission on the evolution of renewable energy sources. And thirdly, on a variety of sources like the European Barometer of renewable energies, data from the industry, etc. With the enlargement of the European Union, the new Member States are required to adopt the RES-E Directive (renewable energy sources for electricity) by 1 May 2004. In the accession treaty, national indicative targets are set and the overall renewable electricity target for the enlarged Union will therefore be 21% of gross electricity consumption by 2010. The Commission has the legal obligation to report on the degree of achievement of new Member States' targets by 2006. Although it is too early to assess RES-policy in the new Member States due to very recently adopted regulations, this document also includes national information on the States now joining the European Union

  6. Modelling of the energy density deposition profiles of ultrashort laser pulses focused in optical media

    International Nuclear Information System (INIS)

    Vidal, F; Lavertu, P-L; Bigaouette, N; Moore, F; Brunette, I; Giguere, D; Kieffer, J-C; Olivie, G; Ozaki, T

    2007-01-01

    The propagation of ultrashort laser pulses in dense optical media is investigated theoretically by solving numerically the nonlinear Schroedinger equation. It is shown that the maximum energy density deposition as a function of the pulse energy presents a well-defined threshold that increases with the pulse duration. As a consequence of plasma defocusing, the maximum energy density deposition is generally smaller and the size of the energy deposition zone is generally larger for shorter pulses. Nevertheless, significant values of the energy density deposition can be obtained near threshold, i.e., at lower energy than for longer pulses

  7. Rapid Convergence of Energy and Free Energy Profiles with Quantum Mechanical Size in Quantum Mechanical-Molecular Mechanical Simulations of Proton Transfer in DNA.

    Science.gov (United States)

    Das, Susanta; Nam, Kwangho; Major, Dan Thomas

    2018-03-13

    In recent years, a number of quantum mechanical-molecular mechanical (QM/MM) enzyme studies have investigated the dependence of reaction energetics on the size of the QM region using energy and free energy calculations. In this study, we revisit the question of QM region size dependence in QM/MM simulations within the context of energy and free energy calculations using a proton transfer in a DNA base pair as a test case. In the simulations, the QM region was treated with a dispersion-corrected AM1/d-PhoT Hamiltonian, which was developed to accurately describe phosphoryl and proton transfer reactions, in conjunction with an electrostatic embedding scheme using the particle-mesh Ewald summation method. With this rigorous QM/MM potential, we performed rather extensive QM/MM sampling, and found that the free energy reaction profiles converge rapidly with respect to the QM region size within ca. ±1 kcal/mol. This finding suggests that the strategy of QM/MM simulations with reasonably sized and selected QM regions, which has been employed for over four decades, is a valid approach for modeling complex biomolecular systems. We point to possible causes for the sensitivity of the energy and free energy calculations to the size of the QM region, and potential implications.

  8. Body size, body composition, and metabolic profile explain higher energy expenditure in overweight children

    Science.gov (United States)

    Lower relative rates of energy expenditure (EE), increased energetic efficiency, and altered fuel utilization purportedly associated with obesity have not been demonstrated indisputably in overweight children. We hypothesized that differences in energy metabolism between nonoverweight and overweight...

  9. Heat demand profiles of energy conservation measures in buildings and their impact on a district heating system

    International Nuclear Information System (INIS)

    Lundström, Lukas; Wallin, Fredrik

    2016-01-01

    Highlights: • Energy savings impact on an low CO 2 emitting district heating system. • Heat profiles of eight building energy conservation measures. • Exhaust air heat pump, heat recovery ventilation, electricity savings etc. • Heat load weather normalisation with segmented multivariable linear regression. - Abstract: This study highlights the forthcoming problem with diminishing environmental benefits from heat demand reducing energy conservation measures (ECM) of buildings within district heating systems (DHS), as the supply side is becoming “greener” and more primary energy efficient. In this study heat demand profiles and annual electricity-to-heat factors of ECMs in buildings are computed and their impact on system efficiency and greenhouse gas emissions of a Swedish biomass fuelled and combined heat and power utilising DHS are assessed. A weather normalising method for the DHS heat load is developed, combining segmented multivariable linear regressions with typical meteorological year weather data to enable the DHS model and the buildings model to work under the same weather conditions. Improving the buildings’ envelope insulation level and thereby levelling out the DHS heat load curve reduces greenhouse gas emissions and improves primary energy efficiency. Reducing household electricity use proves to be highly beneficial, partly because it increases heat demand, allowing for more cogeneration of electricity. However the other ECMs considered may cause increased greenhouse gas emissions, mainly because of their adverse impact on the cogeneration of electricity. If biomass fuels are considered as residuals, and thus assigned low primary energy factors, primary energy efficiency decreases when implementing ECMs that lower heat demand.

  10. Dependence of neutron rate production with accelerator beam profile and energy range in an ADS-TRIGA RC1 reactor

    Energy Technology Data Exchange (ETDEWEB)

    Firoozabadi, M.M.; Karimi, J. [Birjand Univ. (Iran, Islamic Republic of). Dept. of Physics; Zangian, M. [Shahid Beheshti Univ., Tehran (Iran, Islamic Republic of). Nuclear Engineering Dept.

    2016-12-15

    Lead, mercury, tantalum and tungsten were used as target material for calculation of spallation processes in an ADS-TRIGA RC1 reactor. The results show that tungsten has the highest neutron production rate. Therefore it was selected as target material for further calculations. The sensitivity of neutron parameters of the ADS reactor core relative to a change of beam profile and proton energy was determined. The core assembly and parameters of the TRIGA RC1 demonstration facility were used for the calculation model. By changing the proton energy from 115 to 1 400 MeV by using the intra-nuclear cascade model of Bertini (INC-Bertini), the quantity of the relative difference in % for energy gain (G) and spallation neutron yield (Y{sub n/p}), increases to 289.99 % and 5199.15 % respectively. These changes also reduce the amount of relative difference for the proton beam current (I{sub p}) and accelerator power (P{sub acc}), 99.81 % and 81.28 % respectively. In addition, the use of a Gaussian distribution instead of a uniform distribution in the accelerator beam profile increases the quantity of relative difference for energy gain (G), net neutron multiplication (M) and spallation neutron yield (Y{sub n/p}), up to 4.93 %, 4.9 % and 5.55 % respectively.

  11. Competing quantum effects in the free energy profiles and diffusion rates of hydrogen and deuterium molecules through clathrate hydrates.

    Science.gov (United States)

    Cendagorta, Joseph R; Powers, Anna; Hele, Timothy J H; Marsalek, Ondrej; Bačić, Zlatko; Tuckerman, Mark E

    2016-11-30

    Clathrate hydrates hold considerable promise as safe and economical materials for hydrogen storage. Here we present a quantum mechanical study of H 2 and D 2 diffusion through a hexagonal face shared by two large cages of clathrate hydrates over a wide range of temperatures. Path integral molecular dynamics simulations are used to compute the free-energy profiles for the diffusion of H 2 and D 2 as a function of temperature. Ring polymer molecular dynamics rate theory, incorporating both exact quantum statistics and approximate quantum dynamical effects, is utilized in the calculations of the H 2 and D 2 diffusion rates in a broad temperature interval. We find that the shape of the quantum free-energy profiles and their height relative to the classical free energy barriers at a given temperature, as well as the rate of diffusion, are strongly affected by competing quantum effects: above 25 K, zero-point energy (ZPE) perpendicular to the reaction path for diffusion between cavities decreases the quantum rate compared to the classical rate, whereas at lower temperatures tunneling outcompetes the ZPE and as a result the quantum rate is greater than the classical rate.

  12. Integrated Optimization of Speed Profiles and Power Split for a Tram with Hybrid Energy Storage Systems on a Signalized Route

    Directory of Open Access Journals (Sweden)

    Zhuang Xiao

    2018-02-01

    Full Text Available A tram with on-board hybrid energy storage systems based on batteries and supercapacitors is a new option for the urban traffic system. This configuration enables the tram to operate in both catenary zones and catenary-free zones, and the storage of regenerative braking energy for later usage. This paper presents a multiple phases integrated optimization (MPIO method for the coordination of speed profiles and power split considering the signal control strategy. The objective is to minimize the equivalent total energy consumption of all the power sources, which includes both the energy from the traction substation and energy storage systems. The constraints contain running time, variable gradients and curves, speed limits, power balance and signal time at some intersections. The integrated optimization problem is formulated as a multiple phases model based on the characters of the signalized route. An integrated calculation framework, using hp-adaptive pseudospectral method, is proposed for the integrated optimization problem. The effectiveness of the method is verified under fixed time signal (FTS control strategy and tram priority signal (TPS control strategy. Illustrative results show that this method can be successfully applied for trams with hybrid energy storage systems to improve their energy efficiency.

  13. Petroleum refining. 5, refinery operation and management; Le raffinage du petrole. 5. Exploitation et gestion de la raffinerie

    Energy Technology Data Exchange (ETDEWEB)

    Favennec, J.P. (ed.)

    2001-07-01

    In this volume, the reader will find: an analysis of the refining industry's current environment and economics, including the importance of crude oil, the demand for petroleum products, markets and price setting mechanisms for crude oil and oil products, refining costs and margins, the evolution of the refining capacity and of constraints on the industry; a review of the tools available for optimising and controlling operations; an explanation of material balance management and a description of refinery management and organisation. Contents: I. Background to refining. 1. Oil and Energy. 2. Petroleum products applications, characteristics, markets. 3. International oil markets. 4. Refining: a technical summary investments, margins, costs probable future developments. II. Refining tools. 5. Introduction to linear programming as used in the refining industry. 6. Application of linear programming to refining. 7. Automation, process control and information technology. 8. Applications and their implementation. III. Management and organisation. 9. Management and optimisation of refinery operations. 10. Logistics: transport and dispatch. 11. Functional and organisational analysis. 12. Managerial aspects. Glossary. Index. (author)

  14. Material Balance And Reaction Kinetics Modeling For Penex Isomerization Process In Daura Refinery

    Directory of Open Access Journals (Sweden)

    Hamadi Adel Sharif

    2017-01-01

    Full Text Available Penex Deisohexanizer isomerization of light straight run naphtha is a significant process for petroleum refining and proved to be effective technology to produce gasoline components with a high octane number. Modeling of the chemical kinetic reactions is an important tool because it is a better tool for optimization of the experimental data into parameters used for industrial reactors. The present study deals on the isomerization process in Daura refinery. Material balance calculations were done mathematically on the unit for the kinetics prediction purpose. A kinetic mathematical model was derived for the prediction rate constants K1 and K2 and activation energy Ea at operating temperatures range 120-180°C. According to the model, the results show that with increasing of temperature leads to increased K1 directly, where the K2 values proportional inversely. The activation energy results show that Ea1(nC6

  15. Energy Bucket: A Tool for Power Profiling and Debugging of Sensor Nodes

    DEFF Research Database (Denmark)

    Andersen, Jacob; Hansen, Morten Tranberg

    2009-01-01

    The ability to precisely measure and compare energy consumption and relate this to particular parts of programs is a recurring theme in sensor network research. This paper presents the Energy Bucket, a low-cost tool designed for quick empirical measurements of energy consumptions across 5 decades...... of current draw. The Energy Bucket provides a light-weight state API for the target system, which facilitates easy scorekeeping of energy consumption between different parts of a target program. We demonstrate how this tool can be used to discover programming errors and debug sensor network applications.......Furthermore, we show how this tool, together with the target system API, offers a very detailed analysis of where energy is spent in an application, which proves to be very useful when comparing alternative implementations or validating theoretical energy consumption models....

  16. A supply-demand model of fetal energy sufficiency predicts lipid profiles in male but not female Filipino adolescents.

    Science.gov (United States)

    Kuzawa, C W; Adair, L S

    2004-03-01

    To test the hypothesis that the balance between fetal nutritional demand and maternal nutritional supply during pregnancy will predict lipid profiles in offspring measured in adolescence. A total of 296 male and 307 female Filipino offspring (aged 14-16 y) and mothers enrolled in a longitudinal birth cohort study (begun in 1983-84) had lipid profiles measured. Data on maternal height (as a proxy for offspring growth potential and thus fetal nutritional demand) and third trimester maternal arm fat area (as a proxy for maternal supply) were used to create four groups hypothesized to reflect a gradient of fetal energy sufficiency. As fetal energy sufficiency increased among males, there was a decrease in total cholesterol (TC) (Psupply-demand model did not predict any lipid outcome or clinical risk criteria. Our findings in males support the hypothesis that the balance between fetal nutritional demand and maternal nutritional supply has implications for future lipid profiles. The lack of significant associations in females adds to mounting evidence for sex differences in lipid metabolism programming, and may reflect sex differences in fetal nutritional demand. The National Science Foundation, the Mellon Foundation, the Nestle Foundation, and the Emory University Internationalization Program.

  17. The Effect of Electric Load Profiles on the Performance of Off-Grid Residential Hybrid Renewable Energy Systems

    Directory of Open Access Journals (Sweden)

    Stephen Treado

    2015-10-01

    Full Text Available This paper investigates the energy performance of off-grid residential hybrid renewable electric power systems, particularly the effect of electric load profiles on the ability to harvest available solar energy and avoid the consumption of auxiliary energy in the form of propane. The concepts are illustrated by an analysis of the energy performance of electric and propane-fired refrigerators. Off-grid electric power systems frequently incorporate a renewable source, such as wind or solar photovoltaic (PV, with a back-up power provided by a propane fueled motor/generator. Among other design decisions, residential consumers face the choice of employing an electric refrigerator with a conventional vapor compression refrigeration system, or a fuel-fired refrigerator operating as an absorption refrigeration system. One interesting question is whether it is more advantageous from an energy perspective to use electricity to run the refrigerator, which might be provided by some combination of the PV and propane motor/generator, thereby taking advantage of the relatively higher electric refrigerator Coefficient of Performance (COP and free solar energy but having to accept a low electrical conversion efficiency of the motor/generator, or use thermal energy from the combustion of propane to produce the refrigeration effect via an absorption system, albeit with a much lower COP. The analysis is complicated by the fact that most off-grid renewable electrical power systems utilize a battery bank to provide electrical power when it is not available from the wind turbine or PV system, so the state of charge of the battery bank will have a noticeable impact on what energy source is available at any moment in time. Daily electric load profiles combined with variable solar energy input determine the state of charge of the battery bank, with the degree of synchronization between the two being a critical factor in determining performance. The annual energy usage

  18. More evidence of unpublished industry studies of lead smelter/refinery workers

    Science.gov (United States)

    2015-01-01

    Background Lead smelter/refinery workers in the US have had significant exposure to lead and are an important occupational group to study to understand the health effects of chronic lead exposure in adults. Recent research found evidence that studies of lead smelter/refinery workers have been conducted but not published. This paper presents further evidence for this contention. Objectives To present further evidence of industry conducted, unpublished epidemiologic studies of lead smelter/refinery workers and health outcomes. Methods Historical research relying on primary sources such as internal industry documents and published studies. Results ASARCO smelter/refinery workers were studied in the early 1980s and found to have increased risk of lung cancer and stroke in one study, but not in another. Conclusions Because occupational lead exposure is an on-going concern for US and overseas workers, all epidemiologic studies should be made available to evaluate and update occupational health and safety standards. PMID:26070220

  19. Inefficiency of Malaysian palm oil refineries and the impact of different factors on its inefficiency

    Directory of Open Access Journals (Sweden)

    Zahra Shahverdi

    2015-09-01

    Full Text Available This study aimed to analyze changes in the inefficiency of Malaysian palm oil refineries using DEA window analysis method over the period 1996 to 2009. We investigated the effects of different factors on inefficiency of Malaysian palm oil refineries. Based on empirical results, the effect of all factors such as vertical integration, types of ownership, foreign investment, location, experience, and liberalization on inefficiency of refineries was significant. Experience, liberalization, and joint venture between private and public sectors showed an increase in efficiency, while joint venture between local and foreign investment and vertical integration increased refineries’ inefficiency. However, palm oil refineries which were located in the states of Sabah and Sarawak were less technically inefficient than those located in peninsular Malaysia.

  20. Implication of coastal refineries to the ecology of the Gulf of Kachchh

    Digital Repository Service at National Institute of Oceanography (India)

    Zingde, M.D.; Anand, N.M.

    bank of the Gulf of Kachchh. An assessment of probable impact of establishment of these refineries to the rich biodiversity of the Gulf and suggestions to minimise these impacts have been made in this paper....

  1. Detection of impurities in fluid flowing in refinery pipeline or oil production operations using nuclear techniques

    International Nuclear Information System (INIS)

    1981-01-01

    Chlorine (from salt water) and sulphur are determined in crude oil in a well head conduit or refined product in a petroleum refinery by bombardment with neutrons and measuring the gamma rays emitted by neutron capture reactions. (U.K.)

  2. Treating refinery wastewaters in microbial fuel cells using separator electrode assembly or spaced electrode configurations

    KAUST Repository

    Zhang, Fang; Ahn, Yongtae; Logan, Bruce E.

    2014-01-01

    The effectiveness of refinery wastewater (RW) treatment using air-cathode, microbial fuel cells (MFCs) was examined relative to previous tests based on completely anaerobic microbial electrolysis cells (MECs). MFCs were configured with separator

  3. Future fuels: Canada's coast-to-coast network of refineries is emerging from a $3-billion-plus spending binge to take the lead in producing low sulphur gasoline

    International Nuclear Information System (INIS)

    Lunan, D.

    2004-01-01

    A series of investments to convert Canada's 22 operating refineries to produce low-sulphur gasoline are discussed. The investment involves more than $3-billion that will transform Canada's portfolio of aging refineries into one of the most efficient in the western world, and in the process reduce sulphur content in Canadian gasoline to 30 ppm. In some cases the refitting will be completed years ahead of the required 2005 deadline. Total refining capacity in Canada is about 2.5 million barrels per day of crude oil, which includes 580,000 barrels per day of capacity that is dedicated to upgrading bitumen into synthetic crude oil. The initiative to update the refineries was led by Irving Oil, which launched a one billion dollar refit of its 250,000 barrels per day Saint John refinery in the year 2000. Irving Oil's efforts were driven by the company's marketing program in the United States where regional fuel quality standards are higher than national standards either in Canada or the United States. Shell Canada and Imperial Oil are also on track to meet the 30 ppm sulphur level ahead of schedule. For example, Shell Canada is cooperating with Suncor Energy Products in the construction of a hydrotreater at Suncor's Sarnia refinery which will be used to reduce sulphur content of diesel from both the Shell and Suncor refineries, while Imperial Oil is investing over $520 million to refit its refineries in Alberta, Ontario and Nova Scotia. Petro-Canada too, has embarked on a $450 million capital program late in 2003 to introduce low sulphur gasoline; this was in addition to the $1.2 billion program to integrate its bitumen production, upgrading and refining operations. Ultramar launched its $300 million desulphurization program in late 2002; the project is now nearing completion. Refit of Ultramar's Jean Gaulin refinery on Quebec's South Shore will also include a 30,000 barrels per day continuous regeneration platformer to provide a second hydrogen source for the

  4. Profiling high performance dense linear algebra algorithms on multicore architectures for power and energy efficiency

    KAUST Repository

    Ltaief, Hatem; Luszczek, Piotr R.; Dongarra, Jack

    2011-01-01

    This paper presents the power profile of two high performance dense linear algebra libraries i.e., LAPACK and PLASMA. The former is based on block algorithms that use the fork-join paradigm to achieve parallel performance. The latter uses fine

  5. Characterization of the profile of energy consumption in isolated regions of Mozambique; Caracterizacao do perfil de consumo energetico em regioes isoladas de Mocambique

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Afonso Henriques Moreira; Cruz, Ricardo A. Passos da; Magalhaes, Ricardo Nogueira

    2008-07-01

    This article summarizes the characterization of energy demand in isolated regions of Mozambique, the result of a work for government of that country. In essence, the profile does not differ much from Brazilian reality in poor regions, except for tribal characteristics, absent here. The importance of anthropogenic energy and almost no zoogenic energy are still points of major difference between the two realities.

  6. Mechanical energy profiles of the combined ankle-foot system in normal gait: insights for prosthetic designs.

    Science.gov (United States)

    Takahashi, Kota Z; Stanhope, Steven J

    2013-09-01

    Over the last half-century, the field of prosthetic engineering has continuously evolved with much attention being dedicated to restoring the mechanical energy properties of ankle joint musculatures during gait. However, the contributions of 'distal foot structures' (e.g., foot muscles, plantar soft tissue) have been overlooked. Therefore, the purpose of this study was to quantify the total mechanical energy profiles (e.g., power, work, and work-ratio) of the natural ankle-foot system (NAFS) by combining the contributions of the ankle joint and all distal foot structures during stance in level-ground steady state walking across various speeds (0.4, 0.6, 0.8 and 1.0 statures/s). The results from eleven healthy subjects walking barefoot indicated ankle joint and distal foot structures generally performed opposing roles: the ankle joint performed net positive work that systematically increased its energy generation with faster walking speeds, while the distal foot performed net negative work that systematically increased its energy absorption with faster walking speeds. Accounting for these simultaneous effects, the combined ankle-foot system exhibited increased work-ratios with faster walking. Most notably, the work-ratio was not significantly greater than 1.0 during the normal walking speed of 0.8 statures/s. Therefore, a prosthetic design that strategically exploits passive-dynamic properties (e.g., elastic energy storage and return) has the potential to replicate the mechanical energy profiles of the NAFS during level-ground steady-state walking. Copyright © 2013 Elsevier B.V. All rights reserved.

  7. Chemical composition of individual aerosol particles from working areas in a nickel refinery.

    Science.gov (United States)

    Höflich, B L; Wentzel, M; Ortner, H M; Weinbruch, S; Skogstad, A; Hetland, S; Thomassen, Y; Chaschin, V P; Nieboer, E

    2000-06-01

    Individual aerosol particles (n = 1170) collected at work stations in a nickel refinery were analyzed by wavelength-dispersive electron-probe microanalysis. By placing arbitrary restrictions on the contents of sulfur and silicon, the particles could be divided into four main groups. Scanning electron images indicated that most of the particles examined were relatively small (refinery intermediates. The implications of the findings for aerosol speciation measurements, toxicological studies and interpretation of adverse health effects are explored.

  8. BOLIVIA’S ENERGY CONSUMPTION AND ECONOMIC GROWTH PROFILE: IS THERE A LINK?

    Directory of Open Access Journals (Sweden)

    Ismail SOILE

    2016-01-01

    Full Text Available The fundamental importance of energy for socio-economic existence cannot be over-emphasized. With an annual average growth rate of 3.6% over the period of 1998 and 2008, the Bolivian economic statistics shows that over 60% of the country’s GDP growth rate can be attributed to its export sector. However, energy consumption also grew significantly over the same period. Thus we seek to establish the directional causality between energy consumption and economic growth in Bolivia using secondary annual data for the period of 1971 to 2010. The Granger-causality tests indicate that there is an unidirectional causality that runs from economic growth to energy consumption with no feedback. The study, therefore, recommends that policies meant to manage growing energy demand can be instituted without obstructing growth in Bolivia. Energy taxation and pricing reform can help raise additional revenue for development.

  9. ePRO-MP: A Tool for Profiling and Optimizing Energy and Performance of Mobile Multiprocessor Applications

    Directory of Open Access Journals (Sweden)

    Wonil Choi

    2009-01-01

    Full Text Available For mobile multiprocessor applications, achieving high performance with low energy consumption is a challenging task. In order to help programmers to meet these design requirements, system development tools play an important role. In this paper, we describe one such development tool, ePRO-MP, which profiles and optimizes both performance and energy consumption of multi-threaded applications running on top of Linux for ARM11 MPCore-based embedded systems. One of the key features of ePRO-MP is that it can accurately estimate the energy consumption of multi-threaded applications without requiring a power measurement equipment, using a regression-based energy model. We also describe another key benefit of ePRO-MP, an automatic optimization function, using two example problems. Using the automatic optimization function, ePRO-MP can achieve high performance and low power consumption without programmer intervention. Our experimental results show that ePRO-MP can improve the performance and energy consumption by 6.1% and 4.1%, respectively, over a baseline version for the co-running applications optimization example. For the producer-consumer application optimization example, ePRO-MP improves the performance and energy consumption by 60.5% and 43.3%, respectively over a baseline version.

  10. Local electron mean energy profile of positive primary streamer discharge with pin-plate electrodes in oxygen—nitrogen mixtures

    International Nuclear Information System (INIS)

    Sima Wen-Xia; Peng Qing-Jun; Yang Qing; Yuan Tao; Shi Jian

    2013-01-01

    Local electron mean energy (LEME) has a direct effect on the rates of collisional ionization of molecules and atoms by electrons. Electron-impact ionization plays an important role and is the main process for the production of charged particles in a primary streamer discharge. Detailed research on the LEME profile in a primary streamer discharge is extremely important for a comprehensive understanding of the local physical mechanism of a streamer. In this study, the LEME profile of the primary streamer discharge in oxygen-nitrogen mixtures with a pin-plate gap of 0.5 cm under an impulse voltage is investigated using a fluid model. The fluid model includes the electron mean energy density equation, as well as continuity equations for electrons and ions and Poisson's electric field equation. The study finds that, except in the initial stage of the primary streamer, the LEME in the primary streamer tip tends to increase as the oxygen-nitrogen mole ratio increases and the pressure decreases. When the primary streamer bridges the gap, the LEME in the primary streamer channel is smaller than the first ionization energies of oxygen and nitrogen. The LEME in the primary streamer channel then decreases as the oxygen-nitrogen mole ratio increases and the pressure increases. The LEME in the primary streamer tip is primarily dependent on the reduced electric field with mole ratios of oxygen-nitrogen given in the oxygen-nitrogen mixtures. (physics of gases, plasmas, and electric discharges)

  11. PETrA : A Software-Based Tool for Estimating the Energy Profile of Android Applications

    NARCIS (Netherlands)

    Di Nucci, D.; Palomba, F.; Prota, Antonio; Panichella, A.; Zaidman, A.E.; De Lucia, Andrea

    2017-01-01

    Energy efficiency is a vital characteristic of any mobile application, and indeed is becoming an important factor for user satisfaction. For this reason, in recent years several approaches and tools for measuring the energy consumption of mobile devices have been proposed. Hardware-based solutions

  12. Country profiles: Lithuania [Analysis of energy supply options and security of energy supply in the Baltic States

    International Nuclear Information System (INIS)

    2007-01-01

    Lithuania is a very dependent country in terms of energy resources. In 2000 only about 13.8% of the primary energy requirement was covered by domestic resources. The remaining primary fuel requirement is imported from neighbouring countries, mainly from Russia - all crude oil, natural gas and nuclear fuel are imported from this country. There is a concern about the political and economic consequences of this dependence. There is a good interconnection with neighbouring countries for both electrical grid and gas pipelines. The supply of crude oil is also available via pipeline from Russia and two existing oil terminals from other countries, including orimulsion from Venezuela. Coal can be supplied by railway from both Russia and Poland

  13. Reconstruction of the time-averaged sheath potential profile in an argon RF plasma using the ion energy distribution

    International Nuclear Information System (INIS)

    Fivaz, M.; Brunner, S.; Schwarzenbach, W.; Howling, A.A.; Hollenstein, C.

    1994-10-01

    Charge-exchange collisions and radio-frequency excitation combine to give peaks in the ion energy distribution measured at the ground electrode of an argon plasma in a capacitive reactor. These peaks are used as a diagnostic to reconstruct the profile of the time-averaged potential in the sheath. Particle-In-Cell simulations show that the method is accurate. The method is applied to investigate the sheath thickness as a function of excitation frequency at constant plasma power. The time-averaged potential is found to be parabolic in both experimental measurements and numerical simulation. (author) 6 figs., 1 tab., 15 refs

  14. Energy profiles of selected Latin American and Caribbean countries. Report series No. 2

    Energy Technology Data Exchange (ETDEWEB)

    Wu, K.

    1994-07-01

    Countries in this report include Argentina, Bolivia, Brazil, Chile, Colombia, Ecuador, Mexico, Peru, Trinidad and Tobago, and Venezuela. These ten countries are the most important oil and gas producers in the Latin American and the Caribbean region. In the following sections, the primary energy supply (oil, gas, coal, hydroelectricity, and nuclear power whenever they are applicable), primary energy consumption, downstream oil sector development, gas utilization are discussed for each of the ten countries. The report also presents our latest forecasts of petroleum product consumption in each country toward 2000, which form the basis of the outlook for regional energy production and consumption outlined in Report No 1. Since the bulk of primary energy supply and demand is hydrocarbons for many countries, brief descriptions of the important hydrocarbons policy issues are provided at the end of the each country sections.

  15. Energy and Environmental Profile of the U.S. Petroleum Refining Industry

    Energy Technology Data Exchange (ETDEWEB)

    Pellegrino, Joan [Energetics, Inc., Columbia, MD (United States); Brueske, Sabine [Energetics, Inc., Columbia, MD (United States); Carole, Tracy [Energetics, Inc., Columbia, MD (United States); Andres, Howard [Energetics, Inc., Columbia, MD (United States)

    2007-11-01

    This 2007 report provides an overview of the U.S. petroleum refining industry, including new data on market trends and energy and material consumption, as well as information on environmental performance.

  16. Rationalization of imports, refineries and distribution of petroleum in Sub-Saharan Africa

    International Nuclear Information System (INIS)

    Mayorga Alba, E.

    1993-01-01

    This paper outlines policies to secure and reduce the cost of oil supplies in Sub-Saharan Africa (SSA), taking into account the existing forces at play: limited foreign exchange, competition for increasingly scarce funds, and the likely emergence of Africa as the fastest growing centre of energy demand over the coming decade. It identifies major inefficiencies in petroleum procurement, refining and distribution, and analyses the specific bottlenecks at each stage of the supply chain. Many of the diseconomies, estimated to yield savings of US$ 1.4 per year, are traced to an inefficient regulatory set-up in SSA countries, as well as unnecessary government interference in the downstream petroleum sector. In particular, price controls, small topping refineries, monopolistic agencies, government subsidies and opaque management structures prevent the working of efficient market mechanisms. The paper discusses the importance of policy reform, outlining what changes need to be implemented on the levels of institutional arrangements, closing of inefficient units, petroleum pricing and encouraging foreign investment in the sector. (author). 1 ref., 7 figs

  17. Electrochemical pretreatment of heavy oil refinery wastewater using a three-dimensional electrode reactor

    Energy Technology Data Exchange (ETDEWEB)

    Wei Lingyong [State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China); Guo Shaohui, E-mail: cupgsh@163.co [State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China); Yan Guangxu; Chen Chunmao [State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China); Jiang Xiaoyan [Liaohe Petrochemical Branch Company, PetroChina, Panjin 124022 (China)

    2010-12-01

    The pretreatment of heavy oil refinery wastewater (HORW) was experimentally investigated using a three-dimensional electrode reactor (TDER) with granular activated carbon (GAC) and porous ceramsite particle (PCP) as the combination particle electrode and DSA type anodes as the anode. The results showed that higher chemical oxygen demand (COD) removal was obtained in TDER comparing with the two-dimensional electrode reactor (without particle electrodes packed), and combination particle electrode was favorable to improve the COD removal efficiency and reduce the energy consumption. The treated HORW under the optimal experimental condition (GAC percentage = 75%, current density = 30 mA/cm{sup 2}, pH not adjusted and treatment time = 100 min) presented that the removal efficiencies of COD, total organic carbon and toxicity units were 45.5%, 43.3% and 67.2%, respectively, and the ratio of 5-day biochemical oxygen demand to COD was increased from 0.10 to 0.29, which is beneficial for further biological treatment. Furthermore, the application of electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry to characterize polar compounds in HORW and their oxidation products was well demonstrated to reveal the composition variation.

  18. Electrochemical pretreatment of heavy oil refinery wastewater using a three-dimensional electrode reactor

    International Nuclear Information System (INIS)

    Wei Lingyong; Guo Shaohui; Yan Guangxu; Chen Chunmao; Jiang Xiaoyan

    2010-01-01

    The pretreatment of heavy oil refinery wastewater (HORW) was experimentally investigated using a three-dimensional electrode reactor (TDER) with granular activated carbon (GAC) and porous ceramsite particle (PCP) as the combination particle electrode and DSA type anodes as the anode. The results showed that higher chemical oxygen demand (COD) removal was obtained in TDER comparing with the two-dimensional electrode reactor (without particle electrodes packed), and combination particle electrode was favorable to improve the COD removal efficiency and reduce the energy consumption. The treated HORW under the optimal experimental condition (GAC percentage = 75%, current density = 30 mA/cm 2 , pH not adjusted and treatment time = 100 min) presented that the removal efficiencies of COD, total organic carbon and toxicity units were 45.5%, 43.3% and 67.2%, respectively, and the ratio of 5-day biochemical oxygen demand to COD was increased from 0.10 to 0.29, which is beneficial for further biological treatment. Furthermore, the application of electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry to characterize polar compounds in HORW and their oxidation products was well demonstrated to reveal the composition variation.

  19. Effect of current profile evolution on plasma-limiter interaction and the energy confinement time

    International Nuclear Information System (INIS)

    Hawryluk, R.J.; Bol, K.; Bretz, N.

    1979-04-01

    Experiments conducted on the PLT tokamak have shown that both plasma-limiter interaction and the gross energy confinement time are functions of the gas influx during the discharge. By suitably controlling the gas influx, it is possible to contract the current channel, decrease impurity radiation from the core of the discharge, and increase the gross energy confinement time, whether the aperture limiters were of tungsten, stainless steel or carbon

  20. Fine-Grained Energy and Performance Profiling framework for Deep Convolutional Neural Networks

    OpenAIRE

    Rodrigues, Crefeda Faviola; Riley, Graham; Lujan, Mikel

    2018-01-01

    There is a huge demand for on-device execution of deep learning algorithms on mobile and embedded platforms. These devices present constraints on the application due to limited resources and power. Hence, developing energy-efficient solutions to address this issue will require innovation in algorithmic design, software and hardware. Such innovation requires benchmarking and characterization of Deep Neural Networks based on performance and energy-consumption alongside accuracy. However, curren...

  1. The low energy muon beam profile monitor for the muon g-2/EDM experiment at J-PARC

    Science.gov (United States)

    Razuvaev, G. P.; Bae, S.; Choi, H.; Choi, S.; Ko, H. S.; Kim, B.; Kitamura, R.; Mibe, T.; Otani, M.

    2017-09-01

    The muon g-2/EDM experiment at J-PARC aims to measure the muon anomalous magnetic moment and electric dipole moment with high precision by utilising an ultracold muon beam. The current muon g-2 discrepancy between the Standard Model prediction and the experimental value is about 3.5 standard deviations. This experiment requires a development of the muon LINAC to accelerate thermal muons to the 300 MeV/c momentum. Detectors for beam diagnostics play a key role in such an experiment. The beam profile monitoring system has been designed to measure the profile of the low energy muon beam. It was tested during two beam tests in 2016 at the MLF D2 line at J-PARC. The detector was used with positive muons, Mu-(μ+ e- e-), p and H-, e- and UV light. The system overview and preliminary results are given. Special attention is paid to the spatial resolution of the beam profile monitor and online monitor software used during data taking.

  2. Energy, Environmental and Economic Performance of a Micro-trigeneration System upon Varying the Electric Vehicle Charging Profiles

    Directory of Open Access Journals (Sweden)

    Sergio Sibilio

    2017-09-01

    Full Text Available The widespread adoption of electric vehicles and electric heat pumps would result in radically different household electrical demand characteristics, while also possibly posing a threat to the stability of the electrical grid. In this paper, a micro-trigeneration system (composed of a 6.0 kWel cogeneration device feeding a 4.5 kWcool electric air-cooled vapor compression water chiller serving an Italian residential multi-family house was investigated by using the dynamic simulation software TRNSYS. The charging of an electric vehicle was considered by analyzing a set of seven electric vehicle charging profiles representing different scenarios. The simulations were performed in order to evaluate the capability of micro-cogeneration technology in: alleviating the impact on the electric infrastructure (a; saving primary energy (b; reducing the carbon dioxide equivalent emissions (c and determining the operating costs in comparison to a conventional supply system based on separate energy production (d.

  3. Changing energy profiles and consumption patterns following electrification in five rural villages, South Africa

    International Nuclear Information System (INIS)

    Madubansi, M.; Shackleton, C.M.

    2006-01-01

    Following the democratic transition in South Africa in the early 1990s the government has implemented a widespread electrification programme, as well as introduced a free basic electricity allowance as a means of poverty alleviation. Yet there are limited longitudinal studies on the impacts of the introduction of electricity on the patterns of household energy use, and even more so in the neglected rural sector. This study reports on the patterns of household energy use in five rural settlements in 1991 and again in 2002. Results indicate a changing pattern of energy use for lighting and powering entertainment appliances, more specifically from dry-cell batteries and paraffin to electricity. Yet for thermal needs, most notably cooking, fuelwood has remained the most widespread fuel, and the amount used per month has not changed, despite increasing scarcity of wood in the local environment. There has been an increase in the proportion of households purchasing fuelwood as opposed to collecting their own. Overall, the mean total number of fuel types used per household has increased, indicating that electricity is simply viewed as an additional energy, rather than an alternative. Yet, electricity accounted for approximately 60% of expenditure on energy sources in 2002, despite the government's policy of a free basic allowance of 5-6 kWh per month. This has implications for energy supply costing, as well as the poverty alleviation dimensions of the whole programme

  4. A beam profile monitor for heavy ion beams at high impact energies

    International Nuclear Information System (INIS)

    Hausmann, A.; Stiebing, K.E.; Bethge, K.; Froehlich, O.; Koehler, E.; Mueller, A.; Rueschmann, G.

    1994-01-01

    A beam profile monitor for heavy ion beams has been developed for the use in experiments at the Heavy Ion Synchrotron SIS at Gesellschaft fuer Schwerionenforschung Darmstadt (GSI). Four thin scintillation fibres are mounted on one wheel and scan the ion beam sequentially in two linearly independent directions. They are read out via one single photomultiplier common to all four fibres into one time spectrum, which provides all information about beam position, beam extension, time structure and lateral homogeneity of the beam. The system operates in a wide dynamic range of beam intensities. ((orig.))

  5. Yields from pyrolysis of refinery residue using a batch process

    Directory of Open Access Journals (Sweden)

    S. Prithiraj

    2017-12-01

    Full Text Available Batch pyrolysis was a valuable process of assessing the potential of recovering and characterising products from hazardous waste materials. This research explored the pyrolysis of hydrocarbon-rich refinery residue, from crude oil processes, in a 1200 L electrically-heated batch retort. Furthermore, the off-gases produced were easily processed in compliance with existing regulatory emission standards. The methodology offers a novel, cost-effective and environmentally compliant method of assessing recovery potential of valuable products. The pyrolysis experiments yielded significant oil (70% with high calorific value (40 MJ/kg, char (14% with carbon content over 80% and non-condensable gas (6% with significant calorific value (240 kJ/mol. The final gas stream was subjected to an oxidative clean-up process with continuous on-line monitoring demonstrating compliance with South African emission standards. The gas treatment was overall economically optimal as only a smaller portion of the original residue was subjected to emission-controlling steps. Keywords: Batch pyrolysis, Volatiles, Oil yields, Char, Emissions, Oil recovery

  6. Optimization of refinery product blending by using linear programming

    International Nuclear Information System (INIS)

    Ristikj, Julija; Tripcheva-Trajkovska, Loreta; Rikaloski, Ice; Markovska, Liljana

    1999-01-01

    The product slate of a simple refinery consists mainly of liquefied petroleum gas, leaded and unleaded gasoline, jet fuel, diesel fuel, extra light heating oil and fuel oil. The quality of the oil products (fuels) for sale has to comply with the adopted standards for liquid fuels, and the produced quantities have to be comply with the market needs. The oil products are manufactured by blending two or more different fractions which quantities and physical-chemical properties depend on the crude oil type, the way and conditions of processing, and at the same time the fractions are used to blend one or more products. It is in producer's interest to do the blending in an optimal way, namely, to satisfy the requirements for the oil products quality and quantity with a maximal usage of the available fractions and, of course, with a maximal profit out of the sold products. This could be accomplished by applying linear programming, that is by using a linear model for oil products blending optimization. (Author)

  7. Commissioning and startup of the Blind River uranium refinery

    International Nuclear Information System (INIS)

    Schisler, J.M.

    1987-01-01

    In the last five years Eldorado Resources Ltd. (ERL) has undergone a major expansion and modernization of its uranium refining and conversion plants. A new refinery for processing yellow cake to UO/sub 3/ was constructed at Blind River in northern Ontario and started up in 1983. Its rated capacity is 18,000 t/a uranium as UO/sub 3/. At Port Hope, Ontario, ERL's new UF/sub 6/ conversion plant has been constructed. This plant started up in 1984. It utilizes the novel, wet-way process to produce UF/sub 4/ and gives the company a UF/sub 6/ production capacity of 14,500 t/a U. Also at Port Hope is Eldorado's ceramic UO/sub 2/ powder production facility, commissioned in late 1980. It has a capacity of 1700 t/a uranium as UO/sub 2/. With the completion of these capital projects, Eldorado has the largest and most up-to-date refining and conversion facilities in the western world. This paper reviews the refining process and process design. The methodology used to start up the Blind River plant is described as are some startup difficulties, solutions that were developed, and the resultant current operation

  8. Evaluation of wastewater treatment plant at Khartoum refinery company

    International Nuclear Information System (INIS)

    Alnour, Y. A. M.

    2010-03-01

    A wastewater treatment plant has been established in Khartoum Refinery Company in order to treat 1800 meters cubic per day, and to meet the increase in the number of employees and the continued expansion of the company. The study aims to evaluate the performance of the station after a three years period of work, and calculate the efficiency of the station through the following variables: average removal of the biological oxygen demand, chemical oxygen demand, suspended solids and oils, by taking water samples before and after treatment, every week for two month, analysis of samples were conducted in the central laboratory at KRC. The determination of the station efficiency revealed that the station is working well. Treated water characteristics are in conformity with the specifications set by the world Organization Health. It is also proved to be suitable for use in irrigation the amount of water entering to treatment is very large (1500 cubic meters), which lead to dilution of the BOD, COD, SS and oils concentrations. The reason being misuse of water by employees in addition to the large number of damage in the water pipes. The station must be re-evaluated after a certain (5 years) period to determine the impact of future increases of employees, and it is effect on the efficiency of the station. It is recommended to improve the behaviour of employees regarding the use of water, so as to reduce the dilution. (Author)

  9. Regeneration and reuse waste from an edible oil refinery.

    Science.gov (United States)

    Boukerroui, Abdelhamid; Belhocine, Lydia; Ferroudj, Sonia

    2017-08-21

    A spent bleaching earth (SBE) from an edible oil refinery has been regenerated by thermal processing in oven, followed by washing with a cold solution of hydrochloric acid (1M). Optimal regeneration conditions have been controlled by decolorization tests of degummed and neutralized soybean oil. Optimal values of treatment (temperature 350°C, carbonization time 01 h, and HCl concentration 1M) gave a very efficient material. After bleaching oil by regenerated spent bleaching earth (RSBE), the chlorophyll-a and β-carotenes contained in crude edible oil and observed respectively at 430, 454, and 483 nm, value of λ max , are very much decreased. The results obtained after decolorization of edible oil by RSBE material indicate, that, during the process, the bleaching oil did not undergo any changes in the free fatty acid content. The peroxide value (PV) was reduced from 4.2 to 1.8 meq O 2 /kg, and the color has been improved (Lovibond color yellow/red: from 50/0.5 to 2.7/0.3, respectively). The RSBE material obtained was characterized by several techniques (FTIR, SEM). The results show that the heat treatment did not affect the mineral structure of RSBE, and the regenerated material recovered its porous structure.

  10. Treatment of petroleum refinery sourwater by advanced oxidation processes

    International Nuclear Information System (INIS)

    Coelho, Alessandra; Castro, Antonio V.; Dezotti, Marcia; Sant'Anna, G.L.

    2006-01-01

    The performance of several oxidation processes to remove organic pollutants from sourwater was investigated. Sourwater is a specific stream of petroleum refineries, which contains slowly biodegradable compounds and toxic substances that impair the industrial biological wastewater treatment system. Preliminary experiments were conducted, using the following processes: H 2 O 2 , H 2 O 2 /UV, UV, photocatalysis, ozonation, Fenton and photo-Fenton. All processes, except Fenton and photo-Fenton, did not lead to satisfactory results, reducing at most 35% of the sourwater dissolved organic carbon (DOC). Thus, further experiments were performed with these two techniques to evaluate process conditions and organic matter removal kinetics. Batch experiments revealed that the Fenton reaction is very fast and reaches, in a few minutes, an ultimate DOC removal of 13-27%, due to the formation of iron complexes. Radiation for an additional period of 60 min can increase DOC removal up to 87%. Experiments were also conducted in a continuous mode, operating one 0.4 L Fenton stirred reactor and one 1.6 L photo-Fenton reactor in series. DOC removals above 75% were reached, when the reaction system was operated with hydraulic retention times (HRT) higher than 85 min. An empirical mathematical model was proposed to represent the DOC removal kinetics, allowing predicting process performance quite satisfactorily

  11. Towards effective waste management. Knowledge centre Waste Refinery Activity Report 2007-2009; Mot effektivare avfallshantering. Kunskapscentrum Waste Refinery Verksamhetsrapport 2007-2009

    Energy Technology Data Exchange (ETDEWEB)

    2011-07-01

    This report aims to provide a comprehensive picture of the areas that have been discussed and developed during the knowledge centre Waste Refinery first three years. Details and depth analyzes of each area are contained in project reports, which can be downloaded free of charge through our website www.wasterefinery.se

  12. Enhanced piezoelectricity in A B O3 ferroelectrics via intrinsic stress-driven flattening of the free-energy profile

    Science.gov (United States)

    Feng, Yu; Li, Wei-Li; Yu, Yang; Jia, He-Nan; Qiao, Yu-Long; Fei, Wei-Dong

    2017-11-01

    An approach to greatly enhance the piezoelectric properties (˜4 00 pC/N) of the tetragonal BaTi O3 polycrystal using a small number of A -site acceptor-donor substitutions [D. Xu et al., Acta Mater. 79, 84 (2014), 10.1016/j.actamat.2014.07.023] has been proposed. In this study, Pb (ZrTi ) O3 (PZT) based polycrystals with various crystal symmetries (tetragonal, rhombohedral, and so on) were chosen to investigate the piezoelectricity enhancement mechanism. X-ray diffraction results show that doping generates an intrinsic uniaxial compressive stress along the [001] pc direction in the A B O3 lattices. Piezoelectric maps in the parameter space of temperature and Ti concentration in the PZT and doped system show a more significant enhancement effect of L i+-A l3 + codoping in tetragonal PZT than in the rhombohedral phase. Phenomenological thermodynamic analysis indicates that the compressive stress results in more serious flattening of the free-energy profile in tetragonal PZT, compared with that in the rhombohedral phase. The chemical stress obtained by this acceptor-donor codoping can be utilized to optimize the piezoelectric performance on the tetragonal-phase site of the morphotropic phase boundary in the PZT system. The present study provides a promising route to the large piezoelectric effect induced by chemical-stress-driven flattening of the free-energy profile.

  13. Assessing Country’s Reliance on Renewable Energy through Energy Profile and Political Economy Aspects: A Cross Countries Study from 1990 to 2012

    Directory of Open Access Journals (Sweden)

    Santi Hapsari Paramitha

    2017-12-01

    Full Text Available This study examines the relationship between country’s reliance on renewable energy, energy profile, and political economy aspects using dynamic panel data models for a global panel consisting of 43 countries. The time component of our dataset is 1990-2012 inclusive. To make the observation more specific, this study investigates the relationship of a number of sub-samples which are constructed based on the region where the countries belong. In this way, this study ends up with several region samples; namely Western, Asia, Middle East (ME, Africa, Commonwealth of Independent States (CIS, and Latin America. In the empirical part, this study performs a region-based analysis to capture any variations and logical explanation behind them. The results suggest that dependency on oil import, engagement on international environment agreement, economic development, and country size country’s reliance on renewable energy are among the factors that are statistically significant to influence country’s adoption of renewable energy.

  14. Quantum mechanical free energy profiles with post-quantization restraints: Binding free energy of the water dimer over a broad range of temperatures.

    Science.gov (United States)

    Bishop, Kevin P; Roy, Pierre-Nicholas

    2018-03-14

    Free energy calculations are a crucial part of understanding chemical systems but are often computationally expensive for all but the simplest of systems. Various enhanced sampling techniques have been developed to improve the efficiency of these calculations in numerical simulations. However, the majority of these approaches have been applied using classical molecular dynamics. There are many situations where nuclear quantum effects impact the system of interest and a classical description fails to capture these details. In this work, path integral molecular dynamics has been used in conjunction with umbrella sampling, and it has been observed that correct results are only obtained when the umbrella sampling potential is applied to a single path integral bead post quantization. This method has been validated against a Lennard-Jones benchmark system before being applied to the more complicated water dimer system over a broad range of temperatures. Free energy profiles are obtained, and these are utilized in the calculation of the second virial coefficient as well as the change in free energy from the separated water monomers to the dimer. Comparisons to experimental and ground state calculation values from the literature are made for the second virial coefficient at higher temperature and the dissociation energy of the dimer in the ground state.

  15. Neutron energy spectrum flux profile of Ghana's miniature neutron source reactor core

    International Nuclear Information System (INIS)

    Sogbadji, R.B.M.; Abrefah, R.G.; Ampomah-Amoako, E.; Agbemava, S.E.; Nyarko, B.J.B.

    2011-01-01

    Highlights: → The total neutron flux spectrum of the compact core of Ghana's miniature neutron source reactor was studied. → Using 20,484 energy grids, the thermal, slowing down and fast neutron energy regions were studied. - Abstract: The total neutron flux spectrum of the compact core of Ghana's miniature neutron source reactor was understudied using the Monte Carlo method. To create small energy groups, 20,484 energy grids were used for the three neutron energy regions: thermal, slowing down and fast. The moderator, the inner irradiation channels, the annulus beryllium reflector and the outer irradiation channels were the region monitored. The thermal neutrons recorded their highest flux in the inner irradiation channel with a peak flux of (1.2068 ± 0.0008) x 10 12 n/cm 2 s, followed by the outer irradiation channel with a peak flux of (7.9166 ± 0.0055) x 10 11 n/cm 2 s. The beryllium reflector recorded the lowest flux in the thermal region with a peak flux of (2.3288 ± 0.0004) x 10 11 n/cm 2 s. The peak values of the thermal energy range occurred in the energy range (1.8939-3.7880) x 10 -08 MeV. The inner channel again recorded the highest flux of (1.8745 ± 0.0306) x 10 09 n/cm 2 s at the lower energy end of the slowing down region between 8.2491 x 10 -01 MeV and 8.2680 x 10 -01 MeV, but was over taken by the moderator as the neutron energies increased to 2.0465 MeV. The outer irradiation channel recorded the lowest flux in this region. In the fast region, the core, where the moderator is found, the highest flux was recorded as expected, at a peak flux of (2.9110 ± 0.0198) x 10 08 n/cm 2 s at 6.961 MeV. The inner channel recorded the second highest while the outer channel and annulus beryllium recorded very low flux in this region. The flux values in this region reduce asymptotically to 20 MeV.

  16. A national environmental/energy workforce assessment. Post-secondary education profile: energy. Final report on phase 2

    International Nuclear Information System (INIS)

    1978-12-01

    This study is one of 16 volumes aggregating data on representative environmental education offerings in the United States at post-secondary education institutions and in the private sector of the economy. Structured around on-site interviews, the study describes the institutions' education programs--their program structure, representative course offerings, faculty structure, and program requirements. In addition, the study provides information on the employment history of graduates. Designed as Phase II of a three-phase program, the study presents the information on schools with emphasis on energy. The study is an overview. It doesn't include all environmental programs in the United States, and it makes no attempt to evaluate the program offerings

  17. Assessment of refinery effluents and receiving waters using biologically-based effect methods

    International Nuclear Information System (INIS)

    2012-01-01

    Within the EU it is apparent that the regulatory focus on the use of biologically-based effects methods in the assessment of refinery effluents and receiving waters has increased in the past decade. This has been reflected in a recent refinery survey which revealed an increased use of such methods for assessing the quality of refinery effluents and their receiving waters. This report provides an overview of recent techniques used for this purpose. Several case studies provided by CONCAWE member companies describe the application of biological methods to effluent discharge assessment and surface water monitoring. The case studies show that when biological methods are applied to refinery effluents and receiving waters they raise different questions compared with those obtained using physical and chemical methods. Although direct measurement of the toxicity of effluent and receiving to aquatic organisms is the most cited technique, more recent efforts include tests that also address the persistence of effluent toxicity once discharged into the receiving water. Similarly, ecological monitoring of receiving waters can identify effects of effluent inputs arising from species interactions and other secondary effects that would not always be apparent from the results of biological tests conducted on single aquatic organisms. In light of recent and proposed regulatory developments the objectives of this report are therefore to: Discuss the application of biologically-based effects methods (including ecological monitoring) to refinery discharges and receiving waters; Assess the implications of such methods for future regulation of refinery discharges; and Provide guidance on good practice that can be used by refineries and the downstream oil industry to carry out and interpret data obtained using biologically-based effects methods. While the emphasis is on the toxic effects of effluents, other properties will also be covered because of their interdependency in determining

  18. Pursuing the pre-combustion CCS route in oil refineries – The impact on fired heaters

    International Nuclear Information System (INIS)

    Weydahl, Torleif; Jamaluddin, Jamal; Seljeskog, Morten; Anantharaman, Rahul

    2013-01-01

    Highlights: ► The aim is to approach Carbon Capture and Storage (CCS) to refinery fired heaters. ► An identical simplified burner configuration is applied where refinery fuel is replaced with hydrogen. ► Initial simulations indicate that hydrogen replacement do not alter heater operation in a negative way. ► Despite the higher flame temperature in the hydrogen case, the NO x emissions are not higher. ► The prompt-NO mechanism contributes significantly in the refinery fuel case. -- Abstract: The work presented in this paper investigates the effect of replacing refinery fuel gas in the radiant section burners of a fired heater with hydrogen. The aim is to approach pre-combustion CCS to refinery fired heaters by identifying the impact on heat-, flow- and radiation distribution in the lower radiant section of the fired heater when simply switching refinery gas with hydrogen at equivalent power using the same burner geometrics. Additionally the formation of NO x is considered. The investigations are performed using a conventional Reynolds Average Navier Stokes (RANS), Computational Fluid Dynamics (CFD) approach using detailed reaction kinetics consisting of 325 elementary reactions and 53 species. Simplified and generalized furnace and burner geometries are used in the present work. The results show that approximately the same average wall heat flux density is achieved when the refinery fuel is replaced by hydrogen. However, the distribution of heat on the inner surfaces changes. The hydrogen case has, as expected, a higher flame temperature than the base case, nevertheless, the nitric oxide (NO x ) emissions are comparable to base case emissions. Several indications point in the direction of a significant contribution to the base case emissions from the less temperature dependent prompt-NO mechanism, which obviously is not contributing to the hydrogen case emissions.

  19. Urinary excretion of platinum from South African precious metals refinery workers.

    Science.gov (United States)

    Linde, Stephanus J L; Franken, Anja; du Plessis, Johannes L

    2018-03-30

    Urinary platinum (Pt) excretion is a reliable biomarker for occupational Pt exposure and has been previously reported for precious metals refinery workers in Europe but not for South Africa, the world's largest producer of Pt. This study aimed to quantify the urinary Pt excretion of South African precious metals refinery workers. Spot urine samples were collected from 40 workers (directly and indirectly exposed to Pt) at two South African precious metals refineries on three consecutive mornings prior to their shifts. Urine samples were analysed for Pt using inductively coupled plasma-mass spectrometry and were corrected for creatinine content. The urinary Pt excretion of workers did not differ significantly between sampling days. Urinary Pt excretions ranged from work area (P=0.0006; η 2 =0.567) and the number of years workers were employed at the refineries (P=0.003; η 2 =0.261) influenced their urinary Pt excretion according to effect size analyses. Directly exposed workers had significantly higher urinary Pt excretion compared with indirectly exposed workers (P=0.007). The urinary Pt excretion of South African precious metals refinery workers reported in this study is comparable with that of seven other studies conducted in precious metals refineries and automotive catalyst plants in Europe. The Pt body burden of workers is predominantly determined by their work area, years of employment in the refineries and whether they are directly or indirectly exposed to Pt. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  20. Assessment of refinery effluents and receiving waters using biologically-based effect methods

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-01-15

    Within the EU it is apparent that the regulatory focus on the use of biologically-based effects methods in the assessment of refinery effluents and receiving waters has increased in the past decade. This has been reflected in a recent refinery survey which revealed an increased use of such methods for assessing the quality of refinery effluents and their receiving waters. This report provides an overview of recent techniques used for this purpose. Several case studies provided by CONCAWE member companies describe the application of biological methods to effluent discharge assessment and surface water monitoring. The case studies show that when biological methods are applied to refinery effluents and receiving waters they raise different questions compared with those obtained using physical and chemical methods. Although direct measurement of the toxicity of effluent and receiving to aquatic organisms is the most cited technique, more recent efforts include tests that also address the persistence of effluent toxicity once discharged into the receiving water. Similarly, ecological monitoring of receiving waters can identify effects of effluent inputs arising from species interactions and other secondary effects that would not always be apparent from the results of biological tests conducted on single aquatic organisms. In light of recent and proposed regulatory developments the objectives of this report are therefore to: Discuss the application of biologically-based effects methods (including ecological monitoring) to refinery discharges and receiving waters; Assess the implications of such methods for future regulation of refinery discharges; and Provide guidance on good practice that can be used by refineries and the downstream oil industry to carry out and interpret data obtained using biologically-based effects methods. While the emphasis is on the toxic effects of effluents, other properties will also be covered because of their interdependency in determining

  1. Level of energy restriction alters body condition score and morphometric profile in obese Shetland ponies.

    Science.gov (United States)

    Bruynsteen, L; Moons, C P H; Janssens, G P J; Harris, P A; Vandevelde, K; Lefère, L; Duchateau, L; Hesta, M

    2015-10-01

    Due to the high prevalence of obesity in some horses and ponies (especially in the leisure horse sector), effective and safe weight loss strategies are required. The present study evaluated the effect of two different energy restriction rates on physical, morphometric and welfare parameters in 18 obese (body condition score [BCS] 7-9/9) Shetland geldings. The trial was divided into three periods: (1) a 4 week adaptation period, during which the maintenance energy intakes to maintain a stable obese bodyweight were determined (100% MERob); (2) a 16.5-week weight loss period during which the ponies were randomly divided into three groups (n = 6/group) comprising a control group (CONTROL), moderate energy restricted (MOD), and severe energy restricted (SEV) groups that were respectively fed at 100%, 80% and 60% of their individual MERob; and (3) a 3 week follow up period in which the ponies were again fed at their outset individual 100% MERob. Between the start and end of the weight loss period, significant pairwise differences between the three treatment groups were seen for bodyweight, BCS, heart girth, belly girth, and relative ultrasound fat depth at the level of loin and ribs at several time points (P < 0.05). The higher energy restriction was associated with a faster decrease in BCS, tail head, and heart plus belly girth, but no gastric ulcers or stereotypic behaviours were seen. Copyright © 2015 Elsevier Ltd. All rights reserved.

  2. Visualization and analysis of pulsed ion beam energy density profile with infrared imaging

    Science.gov (United States)

    Isakova, Y. I.; Pushkarev, A. I.

    2018-03-01

    Infrared imaging technique was used as a surface temperature-mapping tool to characterize the energy density distribution of intense pulsed ion beams on a thin metal target. The technique enables the measuring of the total ion beam energy and the energy density distribution along the cross section and allows one to optimize the operation of an ion diode and control target irradiation mode. The diagnostics was tested on the TEMP-4M accelerator at TPU, Tomsk, Russia and on the TEMP-6 accelerator at DUT, Dalian, China. The diagnostics was applied in studies of the dynamics of the target cooling in vacuum after irradiation and in the experiments with target ablation. Errors caused by the target ablation and target cooling during measurements have been analyzed. For Fluke Ti10 and Fluke Ti400 infrared cameras, the technique can achieve surface energy density sensitivity of 0.05 J/cm2 and spatial resolution of 1-2 mm. The thermal imaging diagnostics does not require expensive consumed materials. The measurement time does not exceed 0.1 s; therefore, this diagnostics can be used for the prompt evaluation of the energy density distribution of a pulsed ion beam and during automation of the irradiation process.

  3. Energy and environmental profile of the U.S. iron and steel industry

    International Nuclear Information System (INIS)

    Margolis, N.; Sousa, L.

    1997-01-01

    The iron and steel industry, which accounts for between two and three percent of all energy consumed in this country, is also striving to improve its energy efficiency. The amount of energy required to produce a ton of steel has decreased by more than 40% since 1975. This reduction has been accomplished in part through adoption of more energy-efficient and productive processing steps. However, the capital to invest in new technologies is increasingly limited, especially as the costs of environmental control continue to rise. Other than foreign competition, the biggest challenge facing the industry today is compliance with environmental regulations. The Clean Air Act and the Resource Conservation and Recovery Act have had significant impacts on the industry. Since 1970, the industry has invested approximately $6 billion in pollution control systems. The industry spent approximately $230 million in both 1993 and 1994 on capital expenditures for pollution abatement. In a typical year, 15% of the industry's capital investments go to environmental projects. The industry faces even more challenges in the future as new, more stringent regulations are enacted. Topics covered here are: market trends and statistics; energy and materials consumption; and an environmental overview

  4. Frequency Characteristics of Surface Wave Generated by Single-Line Pulsed Laser Beam with Two Kinds of Spatial Energy Profile Models: Gaussian and Square-Like

    Energy Technology Data Exchange (ETDEWEB)

    Seo, Ho Geon; Kim, Myung Hwan; Choi, Sung Ho; Kim, Chung Seok; Jhang, Kyung Young [Hanyang University, Seoul (Korea, Republic of)

    2012-08-15

    Using a single-line pulsed laser beam is well known as a useful noncontact method to generate a directional surface acoustic wave. In this method, different laser beam energy profiles produce different waveforms and frequency characteristics. In this paper, we considered two typical kinds of laser beam energy profiles, Gaussian and square-like, to find out a difference in the frequency characteristics. To achieve this, mathematical models were proposed first for Gaussian laser beam profile and square-like respectively, both of which depended on the laser beam width. To verify the theoretical models, experimental setups with a cylindrical lens and a line-slit mask were respectively designed to produce a line laser beam with Gaussian spatial energy profile and square-like. The frequency responses of the theoretical models showed good agreement with experimental results in terms of the existence of harmonic frequency components and the shift of the first peak frequencies to low.

  5. Temporal changes in fluid chemistry and energy profiles in the vulcano island hydrothermal system.

    Science.gov (United States)

    Rogers, Karyn L; Amend, Jan P; Gurrieri, Sergio

    2007-12-01

    In June 2003, the geochemical composition of geothermal fluids was determined at 9 sites in the Vulcano hydrothermal system, including sediment seeps, geothermal wells, and submarine vents. Compositional data were combined with standard state reaction properties to determine the overall Gibbs free energy (DeltaG(r) ) for 120 potential lithotrophic and heterotrophic reactions. Lithotrophic reactions in the H-O-N-S-C-Fe system were considered, and exergonic reactions yielded up to 120 kJ per mole of electrons transferred. The potential for heterotrophy was characterized by energy yields from the complete oxidation of 6 carboxylic acids- formic, acetic, propanoic, lactic, pyruvic, and succinic-with the following redox pairs: O(2)/H(2)O, SO(4) (2)/H(2)S, NO(3) ()/NH(4) (+), S(0)/H(2)S, and Fe(3)O(4)/Fe(2+). Heterotrophic reactions yielded 6-111 kJ/mol e(). Energy yields from both lithotrophic and heterotrophic reactions were highly dependent on the terminal electron acceptor (TEA); reactions with O(2) yielded the most energy, followed by those with NO(3) (), Fe(III), SO(4) (2), and S(0). When only reactions with complete TEA reduction were included, the exergonic lithotrophic reactions followed a similar electron tower. Spatial variability in DeltaG(r) was significant for iron redox reactions, owing largely to the wide range in Fe(2+) and H(+) concentrations. Energy yields were compared to those obtained for samples collected in June 2001. The temporal variations in geochemical composition and energy yields observed in the Vulcano hydrothermal system between 2001 and 2003 were moderate. The largest differences in DeltaG(r) over the 2 years were from iron redox reactions, due to temporal changes in the Fe(2+) and H(+) concentrations. The observed variations in fluid composition across the Vulcano hydrothermal system have the potential to influence not only microbial diversity but also the metabolic strategies of the resident microbial communities.

  6. The free energy profile of tubulin straight-bent conformational changes, with implications for microtubule assembly and drug discovery.

    Directory of Open Access Journals (Sweden)

    Lili X Peng

    2014-02-01

    Full Text Available αβ-tubulin dimers need to convert between a 'bent' conformation observed for free dimers in solution and a 'straight' conformation required for incorporation into the microtubule lattice. Here, we investigate the free energy landscape of αβ-tubulin using molecular dynamics simulations, emphasizing implications for models of assembly, and modulation of the conformational landscape by colchicine, a tubulin-binding drug that inhibits microtubule polymerization. Specifically, we performed molecular dynamics, potential-of-mean force simulations to obtain the free energy profile for unpolymerized GDP-bound tubulin as a function of the ∼12° intradimer rotation differentiating the straight and bent conformers. Our results predict that the unassembled GDP-tubulin heterodimer exists in a continuum of conformations ranging between straight and bent, but, in agreement with existing structural data, suggests that an intermediate bent state has a lower free energy (by ∼1 kcal/mol and thus dominates in solution. In agreement with predictions of the lattice model of microtubule assembly, lateral binding of two αβ-tubulins strongly shifts the conformational equilibrium towards the straight state, which is then ∼1 kcal/mol lower in free energy than the bent state. Finally, calculations of colchicine binding to a single αβ-tubulin dimer strongly shifts the equilibrium toward the bent states, and disfavors the straight state to the extent that it is no longer thermodynamically populated.

  7. Profiles in Renewable Energy: Case Studies of Successful Utility-Sector

    Science.gov (United States)

    increasingly interested in acquiring hands-on experience with renewable energy technologies in order to plan establish contracts to purchase QFs' power output at "avoided cost," or the cost that the utility state utility regulations. Utility power purchase contracts, which many projects received under the

  8. A retrospective analysis of nickel exposure data at a South African base metal refinery.

    Science.gov (United States)

    Young, Monica M; Van Der Merwe, Cornelius J; Linde, Stefan J L; Du Plessis, Johan L

    2018-03-01

    This study aimed to analyze historical soluble nickel exposure data from a South African base metal refinery and to identify trends in the soluble nickel exposure from 1981 until 2014 in the electrowinning department. Exposure data were presented in an exposure matrix, which described exposure profiles for both area and personal exposures inside two tankhouses. Exposure data were standardized by converting total nickel aerosol concentrations to inhalable nickel concentrations (correction factor 3.0). One-way analyses of variances (ANOVA) were conducted to identify significant differences in log-transformed area and personal exposures from 1982 until 2014, and the trends were assessed with linear regression. Differences were evaluated in area exposure between sections inside the tankhouses, i.e., East, West, and Center bays and in personal exposure between occupations, i.e., cell workers, crane drivers, and supervisors. Area exposure in Tankhouse 1 declined significantly (p ≤ 0.0001) between 1982 and 1986 with a factor of 29. However, after 1986 no significant downward trend in area exposure was evident in Tankhouse 1. Personal exposures in Tankhouse 1 significantly (p ≤ 0.0001) decreased with a factor of three between 1991 and 2014. No significant trends were evident in area and personal exposure in Tankhouse 2. Downward exposure trends were evident in Tankhouse 1 and may be ascribed to the implementation of various control measures and process changes, e.g., increasing polypropylene bead load. Limited data were available for Tankhouse 2, therefore, no trend in exposure could be established. Retrospective analyses may be used to identify trends and anomalies in exposure which might not have been identified during daily exposure monitoring.

  9. U.S. Refinery compliance costs - the elements of and estimate

    International Nuclear Information System (INIS)

    Musgrove, J.G.; Swain, E.J.

    1993-01-01

    A recent National Petroleum Council study identified the environmental costs facing the refining industry from 1995 through 2010. Four broad areas were identified: air pollution control, wastewater treatment, solid and hazardous waste treatment, and occupational health and safety. This paper will present the technical issues and engineering information required to produce an estimate of cost impact. For each of the four areas of impact, the kinds of information required of the refinery manager in order to build an estimate will be tabulated and discussed. For air pollution control, issues will include size and type of unit, product mix of output, and the impact of facility location relative to non-attainment issues. For wastewater, issues will include stormwater segregation, benzene NESHAP, and other treatment system requirements. For hazardous waste treatment, issues will include groundwater protection and leak detection and contaminated soil segregation. For occupational health and safety, issues will include process changes required and worker training required. For all issues, the major dollar factors will be identified as a function of the technical data available. The refinery costs in each areas were estimated for seven groups of refinery sizes. The presentation will conclude with tabulation of cost estimates for each area of investigation and each refinery group. The total costs for each refinery group over the fifteen-year period will also be presented

  10. Predicting refinery effluent toxicity on the basis of hydrocarbon composition determined by GCxGC analysis

    Energy Technology Data Exchange (ETDEWEB)

    Whale, G. [and others

    2013-04-15

    A high resolution analytical method for determining hydrocarbon blocks in petroleum products by comprehensive two-dimensional gas chromatography (GCxGC) was used for the analysis of petroleum hydrocarbons extracted from refinery effluents. From 105 CONCAWE refineries in Europe 111 refinery effluents were collected in the period June 2008 to March 2009 (CONCAWE, 2010). The effluents were analysed for metals, standard effluent parameters (including Chemical Oxygen Demand (COD), Biochemical Oxygen Demand (BOD), oil in water (OiW), GCxGC speciated hydrocarbons, BTEX (Benzene, Toluene, Ethylbenzene, and Xylenes) and volatile organic compounds. This report describes the subsequent analysis of the GCxGC data, as described in hydrocarbon blocks, and uses the PETROTOX model, to predict the environmental toxicity (i.e. ecotoxicity) of the discharged effluents. A further analysis was undertaken to address the potential environmental impact of these predicted effects initially using default dilution factors and then,when necessary site specific factors. The report describes all the methods used to arrive at the predictions, and shows that for the majority of refinery effluents direct toxicity effects in the effluents are not anticipated. Furthermore, when applying either the EU Risk Assessment Technical Guidance Document (TGD) default dilution factors or site specific dilution factors, none of the refineries are predicted to exerting either acute or chronic toxicity to organisms in the receiving aquatic environment, based on their hydrocarbon composition present in the effluent samples.

  11. FEASIBILITY STUDY FOR A PETROLEUM REFINERY FOR THE JICARILLA APACHE TRIBE

    International Nuclear Information System (INIS)

    Jones, John D.

    2004-01-01

    A feasibility study for a proposed petroleum refinery for the Jicarilla Apache Indian Reservation was performed. The available crude oil production was identified and characterized. There is 6,000 barrels per day of crude oil production available for processing in the proposed refinery. The proposed refinery will utilize a lower temperature, smaller crude fractionation unit. It will have a Naphtha Hydrodesulfurizer and Reformer to produce high octane gasoline. The surplus hydrogen from the reformer will be used in a specialized hydrocracker to convert the heavier crude oil fractions to ultra low sulfur gasoline and diesel fuel products. The proposed refinery will produce gasoline, jet fuel, diesel fuel, and a minimal amount of lube oil. The refinery will require about $86,700,000 to construct. It will have net annual pre-tax profit of about $17,000,000. The estimated return on investment is 20%. The feasibility is positive subject to confirmation of long term crude supply. The study also identified procedures for evaluating processing options as a means for American Indian Tribes and Native American Corporations to maximize the value of their crude oil production

  12. Global warming and options for China: energy and environmental policy profile

    International Nuclear Information System (INIS)

    Lin Gan.

    1990-09-01

    This report attempts to give a comprehensive review of current perspectives on energy/environmental problems and policies in China during the last ten years. The second chapter serves as a starting point by giving a general background of the characteristics of economic development and major policy changes in China during the last ten years (1979-89). The third chapter analyzes the characteristics and problems of energy demand and supply in China by breaking down different economic sectors (industry, agriculture, transportation and residential/commercial sectors). The fourth chapter focuses on the problems of CO 2 emissions by giving a historical review of CO 2 emissions by linking up the impact of economic policies and political development in the country during 1950-89. The fifth chapter is mostly devoted to describing policy performance within government environmental policy-making and implementation in the last ten years. Finally, the report concludes by giving several policy recommendations. (Quittner)

  13. The Energy and Identification Continua of Burnout and Work Engagement : Developmental Profiles Over Eight Years

    OpenAIRE

    Mäkikangas, Anne; Hyvönen, Katriina; Feldt, Taru

    2017-01-01

    Understanding of the mutual developmental dynamics between burnout and work engagement is limited due to the lack of longitudinal studies with long follow-ups and multi-wave data. This study sought to identify subgroups of employees characterized by long-term exhaustion-vigor (energy continuum) and cynicism-dedication (identification continuum). A further important aim was to investigate differences between the identified subgroups in their experiences of progress in their personal work goals...

  14. Dynamic segmentation techniques applied to load profiles of electric energy consumption from domestic users

    OpenAIRE

    Benítez Sánchez, Ignacio Javier

    2015-01-01

    [EN] The electricity sector is currently undergoing a process of liberalization and separation of roles, which is being implemented under the regulatory auspices of each Member State of the European Union and, therefore, with different speeds, perspectives and objectives that must converge on a common horizon, where Europe will benefit from an interconnected energy market in which producers and consumers can participate in free competition. This process of liberalization and separation of...

  15. Heart rate profiles and energy cost of locomotion during cross-country skiing races.

    Science.gov (United States)

    Mognoni, P; Rossi, G; Gastaldelli, F; Canclini, A; Cotelli, F

    2001-07-01

    The purpose of this study was to compare heart rate responses and speed in two cross-country skiing races, which were run by seven male and seven female subjects by using classic and free style. Heart rates and skiing velocities were analyzed over flat, uphill and downhill sections, which were run from one to three times. Heart rates were higher in uphill sections than in flat sections; a steady-state heart rate was never reached in the downhill section. When the same uphill section was repeated, the heart rate tended to increase but the speed to decrease. Oxygen uptake (VO2) was calculated from heart rate:VO2 ratio, measured during uphill walking with the aid of poles. The mean (SD) energy cost of locomotion (i.e., the ratio between net VO2 and speed) was 162.1 (9.4) ml.km(-1).kg(-1) and 147.7 (7.1) ml.km(-1).kg(-1) when male subjects ran the flat section after first downhill by using classic and free style, respectively. Females had lower values for VO2 and speed, but similar energy costs. In general, the variability of the energy cost of locomotion in skiers of a similar competitive level is of the same order as that found in uphill walking on a treadmill.

  16. Energy and greenhouse gas profiles of polyhydroxybutyrates derived from corn grain: a life cycle perspective.

    Science.gov (United States)

    Kim, Seungdo; Dale, Bruce E

    2008-10-15

    Polyhydroxybutyrates (PHB) are well-known biopolymers derived from sugars orvegetable oils. Cradle-to-gate environmental performance of PHB derived from corn grain is evaluated through life cycle assessment (LCA), particularly nonrenewable energy consumption and greenhouse gas emissions. Site-specific process information on the corn wet milling and PHB fermentation and recovery processes was obtained from Telles. Most of energy used in the corn wet milling and PHB fermentation and recovery processes is generated in a cogeneration power plant in which corn stover, assumed to be representative of a variety of biomass sources that could be used, is burned to generate electricity and steam. County level agricultural information is used in estimating the environmental burdens associated with both corn grain and corn stover production. Results show that PHB derived from corn grain offers environmental advantages over petroleum-derived polymers in terms of nonrenewable energy consumption and greenhouse gas emissions. Furthermore, PHB provides greenhouse gas credits, and thus PHB use reduces greenhouse gas emissions compared to petroleum-derived polymers. Corn cultivation is one of the environmentally sensitive areas in the PHB production system. More sustainable practices in corn cultivation (e.g., using no-tillage and winter cover crops) could reduce the environmental impacts of PHB by up to 72%.

  17. Characterization of oily sludge from a Tehran oil refinery.

    Science.gov (United States)

    Heidarzadeh, Nima; Gitipour, Saeid; Abdoli, Mohammad Ali

    2010-10-01

    In this study, oily sludge samples generated from a Tehran oil refinery (Pond I) were evaluated for their contamination levels and to propose an adequate remediation technique for the wastes. A simple, random, sampling method was used to collect the samples. The samples were analyzed to measure Total petroleum hydrocarbon (TPH), polyaromatic hydrocarbon (PAH) and heavy metal concentrations in the sludge. Statistical analysis showed that seven samples were adequate to assess the sludge with respect to TPH analyses. The mean concentration of TPHs in the samples was 265,600 mg kg⁻¹. A composite sample prepared from a mix of the seven samples was used to determine the sludge's additional characteristics. Composite sample analysis showed that there were no detectable amounts of PAHs in the sludge. In addition, mean concentrations of the selected heavy metals Ni, Pb, Cd and Zn were 2700, 850, 100, 6100 mg kg⁻¹, respectively. To assess the sludge contamination level, the results from the analysis above were compared with soil clean-up levels. Due to a lack of national standards for soil clean-up levels in Iran, sludge pollutant concentrations were compared with standards set in developed countries. According to these standards, the sludge was highly polluted with petroleum hydrocarbons. The results indicated that incineration, biological treatment and solidification/stabilization treatments would be the most appropriate methods for treatment of the sludges. In the case of solidification/stabilization, due to the high organic content of the sludge, it is recommended to use organophilic clays prior to treatment of the wastes.

  18. Chemical Profiles of Wood Components of Poplar Clones for Their Energy Utilization

    Directory of Open Access Journals (Sweden)

    Danica Kačíková

    2012-12-01

    Full Text Available Selected and tested poplar clones are very suitable biomass resources for various applications such as biofuels, the pulp and paper industry as well as chemicals production. In this study, we determined the content of lignin, cellulose, holocellulose, and extractives, syringyl to guaiacyl (S/G ratio in lignin, and also calculated higher heating values (HHV among eight examined clones of Populus grown on three different experimental sites. The highest lignin content for all the examined sites was determined in ‘I-214’ and ‘Baka 5’ clones, whereas the highest content of extractives was found in ‘Villafranca’ and ‘Baka 5’ clones. The highest S/G ratio for all the examined sites was determined in ‘Villafranca’ and ‘Agathe F’ clones. The chemical profiles of main wood components, extractives, and the S/G ratio in lignin were also influenced by both the experimental site and the clone × site interaction. Higher heating values, derived from calculations based on the contents of lignin and extractives (or lignin only, were in close agreement with the previously published data. The highest heating values were found for ‘Baka 5’ and ‘I-214’ clones. The optimal method of poplar biomass utilization can be chosen on basis of the lignocellulosics chemical composition and the S/G ratio in lignin.

  19. Les raffineries de petite taille dans les pays en développement Small-Size Refineries in Developing Countries

    Directory of Open Access Journals (Sweden)

    Jonchere J. P.

    2006-11-01

    Full Text Available Les raffineries de petite taille, nombreuses dans le monde, vont connaître un regain d'intérêt dans le contexte d'énergie chère que l'on connaît maintenant. Les pays en développement chercheront, plus que jamais, l'autosuffisance en pétrole, moteur essentiel de leur croissance. Toute découverte; même limitée, sera une aubaine et pourra offrir l'opportunité de réaliser une raffinerie. La déficience de l'infrastructure de transports, le manque chronique de moyens de financement et de devises étrangères inciteront nombre de pays en développement à considérer un projet de taille modeste avec intérêt. Des bénéfices substantiels peuvent en être retirés : délai de réalisation court et récupération rapide de la mise financière, montage financier facilité par sa modestie même, amélioration de la balance en devises étrangères, coûts de mise à la disposition du consommateur minimisés, intégration à une politique d'aménagement du territoire. There are many small-size refineries in the worid. Renewed interest will be shown in such refineries within the present context of expensive energy. More than ever the developing countries will seek to gain self sufficiency in cil, the essential locomotive of their growth. Any discovery, even limited, will be a windfall and will provide an opportunity ta build a refinery. Deficiencies in the transportation infrastructure together with the chronic lack of financing means and hard currency will incite a good many developing countries ta consider a modest-size project with interest. Substantiel benefits may be goined, i. e. short construction time and rapid recovery of the financiel outlay, facilitating of the financing by the very modesty of its size, improvement in the hard-currency balance and integration into a regional-development policy.

  20. Investigating an effective supply chain for a refinery in a regulated petroleum sector

    Directory of Open Access Journals (Sweden)

    Chris Adendorf

    2012-12-01

    Full Text Available Currently, refined petroleum products are manufactured by six refineries in South Africa. The supply of refined petroleum products is supplemented by imports of refined petroleum products. These refined petroleum products are transported by pipeline, rail, road, sea and a combination thereof to depots across the country. These products are then distributed directly to commercial customers through points of resale in the form of retail service stations. The challenge is that the storage facilities and distribution networks in South Africa are currently utilised to its full capacity. There is a need to expand current storage infrastructure or to erect new storage facilities to facilitate imports. Durban Port that currently handles 70% of the country’s crude oil and 40% of refined products is also utilised to its full capacity. The investigated problem pertains to the limited storage and transport capacity available for the distribution of petroleum products in the country. The interview protocol, which was based on the literature reviewed, was used for compiling the primary data for the case study. Selected findings revealed that the respondents perceived that storage capacity is the most significant constraint militating against adequate supply by the supply chain. The findings also indicated that the respondents were of the opinion that transport rates and routes (cost of logistics are the greatest contributor to the prices of products. As a result, there appears to be a major scope for improvement in terms of the usage of pipelines and rails for the movement of petroleum products. Keywords: Petroleum products, storage facilities, supply chain, transportation, South African energy sector. Disciplines: civil engineering, architecture, business studies, energy studies