Schematic designs for penetration seals for a reference repository in bedded salt

International Nuclear Information System (INIS)

Kelsall, P.C.; Case, J.B.; Meyer, D.; Coons, W.E.

1982-11-01

The isolation of radioactive wastes in geologic repositories requires that man-made penetrations such as shafts, tunnels, or boreholes are adequately sealed. This report describes schematic seal designs for a repository in bedded salt referenced to the straitigraphy of southeastern New Mexico. The designs are presented for extensive peer review and will be updated as site-specific conceptual designs when a site for a repository in salt has been selected. The principal material used in the seal system is crushed salt obtained from excavating the repository. It is anticipated that crushed salt will consolidate as the repository rooms creep close to the degree that mechanical and hydrologic properties will eventually match those of undisturbed, intact salt. For southeastern New Mexico salt, analyses indicate that this process will require approximately 1000 years for a seal located at the base of one of the repository shafts (where there is little increase in temperature due to waste emplacement) and approximately 400 years for a seal located in an access tunnel within the repository. Bulkheads composed of contrete or salt bricks are also included in the seal system as components which will have low permeability during the period required for salt consolidation

Waste package for a repository located in salt

International Nuclear Information System (INIS)

Basham, S.J. Jr.

1983-01-01

This paper describes the current status of the waste package designs for salt repositories. The status of the supporting studies of environment definition, corrosion of containment materials, and leaching of waste forms is also presented. Emphasis is on the results obtained in FY 83 and the planned effort in FY 84. 8 references, 3 figures, 1 table

Study on the locational criteria for submarine rock repositories of low and medium level radioactive wastes

Energy Technology Data Exchange (ETDEWEB)

Kim, G H; Kang, W J; Kim, T J. and others [Chungnam National Univ., Taejon (Korea, Republic of)

1992-01-15

Submarine repositories have significant advantages over their land counterparts locating close to the areas of daily human activities. Consequently, the construction of submarine repositories on the vast continental shelves around Korean seas is considered to be highly positive. In this context, the development of locational criteria primarily targeting the safety of submarine rock repositories is very important.The contents of the present study are: analyzing characteristics of marine environment: Search of potential hazards to, and environmental impact by, the submarine repositories; Investigation of the oceanographic, geochemical, ecological and sedimentological characteristics of estuaries and coastal seas. Locating potential hazards to submarine repositories by: Bibliographical search of accidents leading to the destruction of submarine structures by turbidity currents and other potentials; Review of turbidity currents. Consideration of environmental impact caused by submarine repositories: Logistics to minimize the environmental impacts in site selection; Removal and dispersion processes of radionuclides in sea water. Analyses of oceanographical characteristics of, and hazard potentials in, the Korean seas. Evaluation of the MOST 91-7 criteria for applicability to submarine repositories and the subsequent proposition of additional criteria.

Study on the locational criteria for submarine rock repositories of low and medium level radioactive wastes

International Nuclear Information System (INIS)

Kim, G. H.; Kang, W. J.; Kim, T. J. and others

1992-01-01

Submarine repositories have significant advantages over their land counterparts locating close to the areas of daily human activities. Consequently, the construction of submarine repositories on the vast continental shelves around Korean seas is considered to be highly positive. In this context, the development of locational criteria primarily targeting the safety of submarine rock repositories is very important.The contents of the present study are: analyzing characteristics of marine environment: Search of potential hazards to, and environmental impact by, the submarine repositories; Investigation of the oceanographic, geochemical, ecological and sedimentological characteristics of estuaries and coastal seas. Locating potential hazards to submarine repositories by: Bibliographical search of accidents leading to the destruction of submarine structures by turbidity currents and other potentials; Review of turbidity currents. Consideration of environmental impact caused by submarine repositories: Logistics to minimize the environmental impacts in site selection; Removal and dispersion processes of radionuclides in sea water. Analyses of oceanographical characteristics of, and hazard potentials in, the Korean seas. Evaluation of the MOST 91-7 criteria for applicability to submarine repositories and the subsequent proposition of additional criteria

The undersea location of the Swedish Final Repository for reactor waste, SFR - human intrusion aspects

International Nuclear Information System (INIS)

Eng, T.

1989-01-01

The Swedish Final Repository for reactor waste, SFR, is built under the Baltic sea close to the Forsmark nuclear power plant. Sixty metres of rock cover the repository caverns under the seabed. The depth of the Baltic sea is about 5-6 m at this location. A human intrusion scenario that in normal inland locations has shown to be of great importance, is a well that is drilled through or in the close vicinity of the repository. Since the land uplift in the SFR area is about 6 mm/year the undersea location of SFR ensures that no well will be drilled at this location for a considerable time while the area is covered by the Baltic sea

Reference Design Description for a Geologic Repository, Rev. 03, ICN 02

International Nuclear Information System (INIS)

Gerald Shideler

2001-01-01

One of the current major national environmental problems is the safe disposal of large quantities of spent nuclear fuel and high-level radioactive waste materials, which are rapidly accumulating throughout the country. These radioactive byproducts are generated as the result of national defense activities and from the generation of electricity by commercial nuclear power plants. At present, spent nuclear fuel is accumulating at over 70 power plant sites distributed throughout 33 states. The safe disposal of these high-level radioactive materials at a central disposal facility is a high national priority. This Reference Design Description explains the current design for a potential geologic repository that may be located at Yucca Mountain in Nevada for the disposal of spent nuclear fuel and high-level radioactive waste materials. This document describes a possible design for the three fundamental parts of a repository: a surface facility, subsurface repository, and waste packaging. It also presents the current conceptual design of the key engineering systems for the final four phases of repository processes: operations, monitoring, closure, and postclosure. In accordance with current law, this design does not include an interim storage option. In addition, this Reference Design Description reviews the expected long-term performance of the potential repository. It describes the natural barrier system which, together with the engineered systems, achieves the repository objectives. This design will protect the public and the environment by allowing the safe disposal of radioactive waste received from government-owned custodial spent fuel sites, high-level radioactive waste sites, and commercial power reactor sites. All design elements meet or exceed applicable regulations governing the disposal of high-level radioactive waste. The design will provide safe disposal of waste materials for at least a 10,000 year period. During this time interval, natural radioactive decay

Definition of the waste package environment for a repository located in salt

International Nuclear Information System (INIS)

Clark, D.E.; Bradley, D.J.

1983-01-01

The expected environmental conditions for emplaced waste packages in a salt repository are simulated in the materials testing program to evaluate performance. Synthetic brines, based on the analyses of actual brines (both intrusion and inclusion), are used for corrosion and leach testing. Elevated temperatures (to 150 0 C) and radiation fields of up to 10 3 rad/h are employed as conservative conditions to bracket expected performance and provide data for worst case scenarios. Obtaining a precise definition of the waste package environment in a salt repository and its change with time is closely tied to detailed site characterization of the candidate salt repository horizon. It is expected that field testing can augment some of the materials testing currently under way and can provide increased confidence in the predicted site-specific near-field conditions. 17 references, 5 figures, 1 table

Site characterization plan overview: reference repository location, Hanford Site, Washington: Consultation draft: Nuclear Waste Policy Act (Section 113)

International Nuclear Information System (INIS)

1988-01-01

As part of the process for siting the nation's first geologic repository for radioactive waste, the Department of Energy (DOE) is preparing a site characterization plan for the Hanford site in Benton County, Washington. As a step in the preparation of that plan, the DOE has provided, for information and review, a consultation draft of the plan to the State of Washington, the affected Indian Tribes - the Confederated Tribes of the Umatilla Indian Reservation, the Nez Perce Indian Tribe, and the Yakima Indian Nation - and the US Nuclear Regulatory Commission. The Hanford site is one of three sites that the DOE currently plans to characterize;the other sites are the Deaf Smith County site in Texas and the Yucca Mountain site in Nevada. After site characterization has been completed and its results evaluated, the DOE will identify from among the three characterized sites the site that is preferred for the repository. The overview presented here consists of brief summaries of important topics covered in the consulation draft of the site characterization plan;it is not a substitute for the site characterization plan. The arrangement of the overview is similar to that of the plan itself, with breif descriptions of the dispoal system - the site, the repository, and the waste package - preceding the discussion of the characterization program to be carried out at the Hanford site. It is intended primarily for the management staff of organizations involved in the DOE's repository program or other persons who might wish to understand the general scope of the site-characterization program, the activities to be conducted, and the facilities to be constructed rather than the technical details of site characterization

A review of construction techniques available for surface and underground radioactive waste repositories

International Nuclear Information System (INIS)

Godfrey, D.G.; Davies, I.L.; MacKenzie, R.D.

1985-01-01

In terms of engineering requirements the construction of surface or indeed underground radioactive waste repositories is not unduly difficult. The civil engineering techniques likely to be required have generally been carried out previously, albeit not in the context of radioactive waste repositories in this country. The emphasis will have to be very much on the quality of construction. This paper emphasises the need for quality construction and describes the techniques likely to be used in the construction of repositories. Reference is made to the materials likely to be used in the construction of repositories and also to the need for being able to convince the designers, regulating authorities and the general public that the materials used will indeed last for the required time. Brief reference is made at the end of the paper to the civil engineering parameters requiring consideration in the location of repository siting. (author)

MRS/IS facility co-located with a repository: preconceptual design and life-cycle cost estimates

International Nuclear Information System (INIS)

Smith, R.I.; Nesbitt, J.F.

1982-11-01

A program is described to examine the various alternatives for monitored retrievable storage (MRS) and interim storage (IS) of spent nuclear fuel, solidified high-level waste (HLW), and transuranic (TRU) waste until appropriate geologic repository/repositories are available. The objectives of this study are: (1) to develop a preconceptual design for an MRS/IS facility that would become the principal surface facility for a deep geologic repository when the repository is opened, (2) to examine various issues such as transportation of wastes, licensing of the facility, and environmental concerns associated with operation of such a facility, and (3) to estimate the life cycle costs of the facility when operated in response to a set of scenarios which define the quantities and types of waste requiring storage in specific time periods, which generally span the years from 1990 until 2016. The life cycle costs estimated in this study include: the capital expenditures for structures, casks and/or drywells, storage areas and pads, and transfer equipment; the cost of staff labor, supplies, and services; and the incremental cost of transporting the waste materials from the site of origin to the MRS/IS facility. Three scenarios are examined to develop estimates of life cycle costs of the MRS/IS facility. In the first scenario, HLW canisters are stored, starting in 1990, until the co-located repository is opened in the year 1998. Additional reprocessing plants and repositories are placed in service at various intervals. In the second scenario, spent fuel is stored, starting in 1990, because the reprocessing plants are delayed in starting operations by 10 years, but no HLW is stored because the repositories open on schedule. In the third scenario, HLW is stored, starting in 1990, because the repositories are delayed 10 years, but the reprocessing plants open on schedule

Overview of the current CRWMS repository design

International Nuclear Information System (INIS)

Daniel, R.B.; Teraoka, G.M.

1998-01-01

This paper summarizes the current design for a potential geologic repository for spent fuels and high-level wastes at Yucca Mountain, Nevada. The objective of the paper is to present the key design features of the Mined Geologic Disposal System (MGDS) surface facilities and MGDS subsurface facilities. The paper describes the following: surface layout; waste handling operations design; subsurface design; and the underground transport and emplacement design. A more detailed presentation of key features is provided in the ''Reference design description for a geologic repository'' which is located on the YMP Homepage at www.ymp.gov

Reference Device-Assisted Adaptive Location Fingerprinting

Directory of Open Access Journals (Sweden)

Dongjin Wu

2016-06-01

Full Text Available Location fingerprinting suffers in dynamic environments and needs recalibration from time to time to maintain system performance. This paper proposes an adaptive approach for location fingerprinting. Based on real-time received signal strength indicator (RSSI samples measured by a group of reference devices, the approach applies a modified Universal Kriging (UK interpolant to estimate adaptive temporal and environmental radio maps. The modified UK can take the spatial distribution characteristics of RSSI into account. In addition, the issue of device heterogeneity caused by multiple reference devices is further addressed. To compensate the measuring differences of heterogeneous reference devices, differential RSSI metric is employed. Extensive experiments were conducted in an indoor field and the results demonstrate that the proposed approach not only adapts to dynamic environments and the situation of changing APs’ positions, but it is also robust toward measuring differences of heterogeneous reference devices.

Design of repository sealing systems - 1981

International Nuclear Information System (INIS)

Ellison, R.D.; Shukla, D.K.; Kelsall, P.C.; D'Appolonia Consulting Engineers, Albuquerque, NM)

1982-01-01

Isolating nuclear waste in geologic repositories will require the sealing of penetrations such as access shafts and tunnels, disposal rooms, and exploration boreholes. This paper discusses seal designs developed for a repository in bedded salt referenced to the stratigraphy of southeastern New Mexico. Designs are based on a multiple component concept whereby individual components are designed for a specific function and location. For a repository in salt the major function of the seals is to exclude groundwater inflow. Two main types of component are included for this purpose: (1) bulk-heads are dense concrete structures keyed into the walls of the penetration and are intended to reduce flow at the interface between the seal and the salt; (2) backfills are granular materials compacted in place in the penetration. In the repository the major backfill material is crushed salt, which is expected to consolidate and recrystallize as the rooms close in response to salt creep. Densely compacted clays will be used as backfill in the shafts closer to potential sources of water inflow. 22 references, 10 figures, 1 table

Suggestions for locations for the surface installations required for deep-lying repositories; standortareale fuer die oberflaechenanlage von tiefenlagern -- vorschlaege zur diskussion

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-01-15

This booklet issued by the Swiss National Cooperative for the Disposal of Radioactive Waste NAGRA takes a look at the various factors involved in the selection of locations for surface installations that are required for the operation of deep-lying nuclear waste repositories. The method chosen for the selection of possible locations for surface installations is explained and the necessity for such installations is discussed. The requirements placed on such a location are discussed and the various locations chosen for further consideration are noted. The evaluation phases involved in the selection of sites are described. The proposed surface installations are noted and the proposed structures for both repository types - for highly radioactive wastes and for low and medium active wastes - are described.

Numerical modeling of ground-water flow systems in the vicinity of the reference repository location, Hanford Site, Washington

International Nuclear Information System (INIS)

Davis, P.; Beyeler, W.; Logsdon, M.; Coleman, N.; Brinster, K.

1989-04-01

This report documents south-central Washington State's Pasco Basin ground-water modeling studies. This work was done to support the NRC's review of hydrogeologic studies under the Department of Energy's (DOE) Basalt Waste Isolation Project. The report provides a brief overview of the geology, hydrology, and hydrochemistry of the Pasco Basin as a basis for the evaluation of previous conceptual and numerical ground-water flow models of the region. Numerical models were developed to test new conceptual models of the site and to provide a means of evaluating the Department of Energy's performance assessments and proposed hydrologic testing. Regional ground-water flow modeling of an area larger than the Pasco Basin revealed that current concepts on the existence and behavior of a hydrologic barrier west of the proposed repository location are inconsistent with available data. This modeling also demonstrated that the measured pattern of hydraulic heads cannot be produced with a model that (1) has uniform layer properties over the entire domain; (2) has zones of large conductivity associated with anticlinal structures; or (3) includes recharge from the industrial disposal ponds. Adequate representation of the measured hydraulic heads was obtained with a model that contained regions of larger hydraulic conductivity that corresponded to the presence of sedimentary interbeds. In addition, a detailed model of a region smaller than the Pasco Basin was constructed to provide the NRC staff with the ability to analyze proposed Department of Energy hydrologic tests. 62 refs., 145 figs., 18 tabs

Surface hydrologic characteristics of proposed repository locations in the Palo Duro Basin of the Texas Panhandle

International Nuclear Information System (INIS)

1985-04-01

This report provides a description of the surface hydrology in the two proposed locations of a high-level waste repository within the Palo Duro Basin of the Texas Panhandle. Included for consideration are the topography; the major drainage systems - Palo Duro, Tierra Blanca, and Tule Creeks, and Prairie Dog Town Fork of the Red River; and the most prominent impoundments, the playa lakes. The magnitude and frequency of precipitation throughout the region are discussed, and rainfall depth-duration-area data for the 100-year, 500-year, and probable maximum storms are presented. Soil properties are also described, with specific reference to the infiltration and runoff processes and the contribution of these processes to Ogallala aquifer recharge. A summary discussion of the local streams includes information on historical streamflow, a brief description of flooding, and results of a study of floodplains for the 100-year, 500-year, and probable maximum storms. The report concludes with a characterization of the water quality of these streams and an explanation of the local geologic influences on stream-water chemistry. 25 figures, 20 tables

Safety analysis of the VLJ repository

International Nuclear Information System (INIS)

Vieno, T.; Nordman, H.

1991-05-01

The VLJ repository is an underground disposal facility for the low and medium level waste generated at the Olkiluoto nuclear power plant. The repository is located within 1 km from TVO I and TVO II (2 x 710 MWe) BWR's on the Olkiluoto island at the west coast of Finland. It contains two rock silos excavated at the depth of 60...100 meters in the bedrock. Low level waste will be disposed of in a shotcreted rock silo. For bituminized medium level waste, a separate silo of reinforced concrete has been built inside the shotcreted rock silo. The post-closure safety analysis has been done for the Final Safety Analysis Report (FSAR) of the VLJ repository. In addition to the normal evolution scenario, several disturbed evolution and accident scenarios have been analysed. In the reference scenario, radio-nuclides are assumed to be released from the bituminized waste within 500 years, the concrete silo is assumed to gradually disintegrate and finally to collapse at 5 000 years, all concrete in the silo is assumed to be also chemically depleted within 6 000 years, and all the seals of the repository are assumed to deteriorate within 12 000 years. The ability of alone natural barriers to restrict the release of radionuclides into the biosphere has been evaluated by means of scenarios where the degradation of engineered barriers has been assumed to take place at a still faster rate. In one of the disturbed evolution scenarios it has been assumed that the concrete silo for medium level waste is severely impaired immediately after sealing of the repository. Effects of gas generation and consequences of human intrusion have been evaluated, too. The results of the safety analysis show that radiation doses of any significance are caused only if a well is bored in the vicinity of the repository or if the groundwater discharge spot is inhabited and used for cultivation. In the reference scenario the maximum expectation value of the individual dose rate is 0.3 mSv/a

Postclosure risks of alternative SRP nuclear waste forms in geologic repositories

International Nuclear Information System (INIS)

Cheung, H.; Edwards, L.; Harvey, T.; Revelli, M.

1982-05-01

The postclosure risk of REFERENCE and ALTERNATIVE waste forms for the defense high-level waste at the Savannah River Plant (SRP) were compared by analyses with a computer code, MISER, written to study the effects of repository features in a probabilistic framework. MISER traces radionuclide flows through a network of stream tubes from the repository to risk-sensitive points. Uncertainties in waste form, package properties, and geotechnical data are accounted for with Monte Carlo techniques. Our results show: (1) for generic layered-salt and basalt repositories, the difference in performance between the two waste forms is insignificant; (2) where the doses are sensitive to uncertainties in leaching rates, the doses are orders of magnitude below background; (3) disruptive events contribute only slightly to the risk of a layered-salt repository; (4) simple design alterations have strong effects on near field doses; (5) great care should be exercised in selecting the location at which repository risks are to be measured, calculated, or regulated

Preliminary design of the repository. Stage 2

International Nuclear Information System (INIS)

Saanio, T.; Kirkkomaeki, T.; Keto, P.; Kukkola, T.; Raiko, H.

2007-04-01

Spent nuclear fuel from Finnish nuclear power plants will be disposed of in deep bedrock in Olkiluoto, Eurajoki. The repository is planned to be excavated at a depth of 400 - 500 metres. Access routes to the repository include a 1:10 inclined access tunnel, and vertical shafts. The fuel is encapsulated in the encapsulation plant above ground and transferred to the repository in the canister lift. Deposition tunnels, central tunnels and technical rooms are excavated at the disposal level. The canisters are deposited in deposition holes that are covered with bentonite blocks. The deposition holes are bored in the floors of the deposition tunnels. The central tunnel system consists of two parallel central tunnels that are inter-connected at certain distances. Two parallel central tunnels improve the fire safety of the rooms and also allow flexible backfilling and closing of the deposition tunnels in stages at the operational phase of the repository. An underground rock characterization facility, ONKALO, is excavated at the disposal level to support and confirm investigations carried out from above ground. ONKALO is designed so that it can later serve as part of the repository. ONKALO excavations were started in 2004. The repository will be excavated in the 2010s and operation will start in 2020. The fifth nuclear power unit makes the operational phase of the repository very long. Parts of the repository will be excavated and closed over the long operational period. The repository can be constructed at one or several levels. The one-storey alternative is the so-called reference alternative in this preliminary design report. The two-storey alternative is also taken into account in the ONKALO designs. The preliminary designs of the repository are presented as located in Olkiluoto. The location of the repository will be revised when more information on the bedrock has been gained. More detailed data of the circumstances will be obtained from above ground investigations

Preliminary design of the repository, stage 2

International Nuclear Information System (INIS)

Saanio, T.; Kirkkomaeki, T.; Keto, P.; Kukkola, T.; Raiko, H.

2007-01-01

Spent nuclear fuel from Finnish nuclear power plants will be disposed of in deep bedrock in Olkiluoto, Eurajoki. The repository is planned to be excavated at a depth of 400 - 500 metres. Access routes to the repository include a 1:10 inclined access tunnel, and vertical shafts. The fuel is encapsulated in the encapsulation plant above ground and transferred to the repository in the canister lift. Deposition tunnels, central tunnels and technical rooms are excavated at the disposal level. The canisters are deposited in deposition holes that are covered with bentonite blocks. The deposition holes are bored in the floors of the deposition tunnels. The central tunnel system consists of two parallel central tunnels that are inter-connected at certain distances. Two parallel central tunnels improve the fire safety of the rooms and also allow flexible backfilling and closing of the deposition tunnels in stages at the operational phase of the repository. An underground rock characterization facility, ONKALO, is excavated at the disposal level to support and confirm investigations carried out from above ground. ONKALO is designed so that it can later serve as part of the repository. ONKALO excavations were started in 2004. The repository will be excavated in the 2010s and operation will start in 2020. The fifth nuclear power unit makes the operational phase of the repository very long. Parts of the repository will be excavated and closed over the long operational period. The repository can be constructed at one or several levels. The one-storey alternative is the so-called reference alternative in this preliminary design report. The two-storey alternative is also taken into account in the ONKALO designs. The preliminary designs of the repository are presented as located in Olkiluoto. The location of the repository will be revised when more information on the bedrock has been gained. More detailed data of the circumstances will be obtained from above ground investigations

Selection of candidate canister materials for high-level nuclear waste containment in a tuff repository

International Nuclear Information System (INIS)

McCright, R.D.; Weiss, H.; Juhas, M.C.; Logan, R.W.

1983-11-01

A repository located at Yucca Mountain at the Nevada Test Site is a potential site for permanent geological disposal of high-level nuclear waste. The repository can be located in a horizon in welded tuff, a volcanic rock, which is above the static water level at this site. The environmental conditions in this unsaturated zone are expected to be air and water vapor dominated for much of the containment period. Type 304L stainless steel is the reference material for fabricating canisters to contain the solid high-level wastes. Alternative stainless alloys are considered because of possible susceptibility of 304L to localized and stress forms of corrosion. For the reprocessed glass wastes, the canisters serve as the recipient for pouring the glass with the result that a sensitized microstructure may develop because of the times at elevated temperatures. Corrosion testing of the reference and alternative materials has begun in tuff-conditioned water and steam environments. 21 references, 8 figures, 8 tables

Assessment of Effectiveness of Geologic Isolation Systems: REFERENCE SITE INITIAL ASSESSMENT FOR A SALT DOME REPOSITORY

Energy Technology Data Exchange (ETDEWEB)

Harwell, M. A.; Brandstetter, A.; Benson, G. L.; Raymond, J. R.; Brandley, D. J.; Serne, R. J.; Soldat, J. K.; Cole, C. R.; Deutsch, W. J.; Gupta, S. K.; Harwell, C. C.; Napier, B. A.; Reisenauer, A. E.; Prater, L. S.; Simmons, C. S.; Strenge, D. L.; Washburn, J. F.; Zellmer, J. T.

1982-06-01

As a methodology demonstration for the Office of Nuclear Waste Isolation (ONWI), the Assessment of Effectiveness of Geologic Isolation Systems (AEGIS) Program conducted an initial reference site analysis of the long-term effectiveness of a salt dome repository. The Hainesville Salt Dome in Texas was chosen to be representative of the Gulf Coast interior salt domes; however, the Hainesville Site has been eliminated as a possible nuclear waste repository site. The data used for this exercise are not adequate for an actual assessment, nor have all the parametric analyses been made that would adequately characterize the response of the geosystem surrounding the repository. Additionally, because this was the first exercise of the complete AEGIS and WASTE Rock Interaction Technology (WRIT) methodology, this report provides the initial opportunity for the methodology, specifically applied to a site, to be reviewed by the community outside the AEGIS. The scenario evaluation, as a part of the methodology demonstration, involved consideration of a large variety of potentially disruptive phenomena, which alone or in concert could lead to a breach in a salt dome repository and to a subsequent transport of the radionuclides to the environment. Without waste- and repository-induced effects, no plausible natural geologic events or processes which would compromise the repository integrity could be envisioned over the one-million-year time frame after closure. Near-field (waste- and repository-induced) effects were excluded from consideration in this analysis, but they can be added in future analyses when that methodology development is more complete. The potential for consequential human intrusion into salt domes within a million-year time frame led to the consideration of a solution mining intrusion scenario. The AEGIS staff developed a specific human intrusion scenario at 100 years and 1000 years post-closure, which is one of a whole suite of possible scenarios. This scenario

Effects of resource activities upon repository siting and waste containment with reference to bedded salt

International Nuclear Information System (INIS)

Ashby, J.; Rowe, J.

1980-02-01

The primary consideration for the suitability of a nuclear waste repository site is the overall ability of the repository to safely contain radioactive waste. This report is a discussion of the past, present, and future effects of resource activities on waste containment. Past and present resource activities which provide release pathways (i.e., leaky boreholes, adjacent mines) will receive initial evaluation during the early stages of any repository site study. However, other resource activities which may have subtle effects on containment (e.g., long-term pumping causing increased groundwater gradients, invasion of saline water causing lower retardation) and all potential future resource activities must also be considered during the site evaluation process. Resource activities will affect both the siting and the designing of repositories. Ideally, sites should be located in areas of low resource activity and low potential for future activity, and repository design should seek to eliminate or minimize the adverse effects of any resource activity. Buffer zones should be created to provide areas in which resource activities that might adversely affect containment can be restricted or curtailed. This could mean removing large areas of land from resource development. The impact of these frozen assets should be assessed in terms of their economic value and of their effect upon resource reserves. This step could require a major effort in data acquisition and analysis followed by extensive numerical modeling of regional fluid flow and mass transport. Numerical models should be used to assess the effects of resource activity upon containment and should include the cumulative effects of different resource activities. Analysis by other methods is probably not possible except for relatively simple cases

Location performance objectives for the NNWSI area-to-location screening activity

Energy Technology Data Exchange (ETDEWEB)

Sinnock, S.; Fernandez, J.A.

1984-01-01

Fifty-four objectives were identified to guide the screening of the Nevada Research and Development Area of the Nevada Test Site for relatively favorable locations for the disposal of nuclear waste in a mined geologic repository. The objectives were organized as a hierarchy composed of 4 upper-level, 12 middle-level, and 38 lower-level objectives. The four upper-level objectives account for broad national goals to contain and isolate nuclear waste in an environmentally sound and economically acceptable manner. The middle-level objectives correspond to topical categories that logically relate the upper-level objectives to site-specific concerns such as seismicity, sensitive species, and flooding hazards (represented by the lower-level objectives). The relative merits of alternative locations were compared by an application of decision analysis based on standard utility theory. The relative favorabilities of pertinent physical conditions at each alternative location were weighted in relation to the importance of objectives, and summed to produce maps indicating the most and the least favorable locations. Descriptions of the objectives were organized by the hierarchical format; they detail the applicability of each objective to geologic repository siting, previously published siting criteria corresponding to each objective, and the rationale for the weight assigned to each objective, and the pertinent attributes for evaluating locations with respect to each objective. 51 references, 47 figures, 4 tables.

Location performance objectives for the NNWSI area-to-location screening activity

International Nuclear Information System (INIS)

Sinnock, S.; Fernandez, J.A.

1984-01-01

Fifty-four objectives were identified to guide the screening of the Nevada Research and Development Area of the Nevada Test Site for relatively favorable locations for the disposal of nuclear waste in a mined geologic repository. The objectives were organized as a hierarchy composed of 4 upper-level, 12 middle-level, and 38 lower-level objectives. The four upper-level objectives account for broad national goals to contain and isolate nuclear waste in an environmentally sound and economically acceptable manner. The middle-level objectives correspond to topical categories that logically relate the upper-level objectives to site-specific concerns such as seismicity, sensitive species, and flooding hazards (represented by the lower-level objectives). The relative merits of alternative locations were compared by an application of decision analysis based on standard utility theory. The relative favorabilities of pertinent physical conditions at each alternative location were weighted in relation to the importance of objectives, and summed to produce maps indicating the most and the least favorable locations. Descriptions of the objectives were organized by the hierarchical format; they detail the applicability of each objective to geologic repository siting, previously published siting criteria corresponding to each objective, and the rationale for the weight assigned to each objective, and the pertinent attributes for evaluating locations with respect to each objective. 51 references, 47 figures, 4 tables

Reference Priors for the General Location-Scale Model

NARCIS (Netherlands)

Fernández, C.; Steel, M.F.J.

1997-01-01

The reference prior algorithm (Berger and Bernardo 1992) is applied to multivariate location-scale models with any regular sampling density, where we establish the irrelevance of the usual assumption of Normal sampling if our interest is in either the location or the scale. This result immediately

Locating and parsing bibliographic references in HTML medical articles.

Science.gov (United States)

Zou, Jie; Le, Daniel; Thoma, George R

2010-06-01

The set of references that typically appear toward the end of journal articles is sometimes, though not always, a field in bibliographic (citation) databases. But even if references do not constitute such a field, they can be useful as a preprocessing step in the automated extraction of other bibliographic data from articles, as well as in computer-assisted indexing of articles. Automation in data extraction and indexing to minimize human labor is key to the affordable creation and maintenance of large bibliographic databases. Extracting the components of references, such as author names, article title, journal name, publication date and other entities, is therefore a valuable and sometimes necessary task. This paper describes a two-step process using statistical machine learning algorithms, to first locate the references in HTML medical articles and then to parse them. Reference locating identifies the reference section in an article and then decomposes it into individual references. We formulate this step as a two-class classification problem based on text and geometric features. An evaluation conducted on 500 articles drawn from 100 medical journals achieves near-perfect precision and recall rates for locating references. Reference parsing identifies the components of each reference. For this second step, we implement and compare two algorithms. One relies on sequence statistics and trains a Conditional Random Field. The other focuses on local feature statistics and trains a Support Vector Machine to classify each individual word, followed by a search algorithm that systematically corrects low confidence labels if the label sequence violates a set of predefined rules. The overall performance of these two reference-parsing algorithms is about the same: above 99% accuracy at the word level, and over 97% accuracy at the chunk level.

Waste package/repository impact study: Final report

Energy Technology Data Exchange (ETDEWEB)

1985-09-01

The Waste Package/Repository Impact Study was conducted to evaluate the feasibility of using the current reference salt waste package in the salt repository conceptual design. All elements of the repository that may impact waste package parameters, i.e., (size, weight, heat load) were evaluated. The repository elements considered included waste hoist feasibility, transporter and emplacement machine feasibility, subsurface entry dimensions, feasibility of emplacement configuration, and temperature limits. The evaluations are discussed in detail with supplemental technical data included in Appendices to this report, as appropriate. Results and conclusions of the evaluations are discussed in light of the acceptability of the current reference waste package as the basis for salt conceptual design. Finally, recommendations are made relative to the salt project position on the application of the reference waste package as a basis for future design activities. 31 refs., 11 figs., 11 tabs.

Waste package/repository impact study: Final report

International Nuclear Information System (INIS)

1985-09-01

The Waste Package/Repository Impact Study was conducted to evaluate the feasibility of using the current reference salt waste package in the salt repository conceptual design. All elements of the repository that may impact waste package parameters, i.e., (size, weight, heat load) were evaluated. The repository elements considered included waste hoist feasibility, transporter and emplacement machine feasibility, subsurface entry dimensions, feasibility of emplacement configuration, and temperature limits. The evaluations are discussed in detail with supplemental technical data included in Appendices to this report, as appropriate. Results and conclusions of the evaluations are discussed in light of the acceptability of the current reference waste package as the basis for salt conceptual design. Finally, recommendations are made relative to the salt project position on the application of the reference waste package as a basis for future design activities. 31 refs., 11 figs., 11 tabs

Geotechnical materials considerations for conceptual repository design in the Palo Duro Basin, Texas

International Nuclear Information System (INIS)

Versluis, W.S.; Balderman, M.A.

1984-01-01

The Palo Duro Basin is only one of numerous potential repository locations for placement of a nuclear waste repository. Conceptual designs in the Palo Duro Basin involve considerations of the character and properties of the geologic materials found on several sites throughout the Basin. The first consideration presented includes current basin exploration results and interpretations of engineering properties for the basin geologic sequences. The next consideration presented includes identification of the characteristics of rock taken from the geologic sequence of interest through laboratory and field testing. Values for materials properties of representative samples are obtained for input into modeling of the material response to repository placement. Conceptual designs which respond to these geotechnical considerations are discussed. 4 references, 4 figures, 4 tables

Performance analysis of a repository for low and intermediate level reactor waste

International Nuclear Information System (INIS)

Vieno, T.; Nordman, H.; Vuori, S.; Peltonen, E.

1987-01-01

In Finland, utilities producing nuclear energy are responsible for the management of the radioactive waste, including final disposal. As regards low and intermediate level waste, the approach has been adopted to employ the power plant sites for locations of repositories. The repositories will be excavated at the depth of about 50 to 125 m in the bedrock of the two Finnish nuclear power plant sites, Loviisa and Olkiluoto. The performance analysis presented in this paper has been carried out for the Preliminary Safety Analysis Report (PSAR) of the Olkiluoto repository. A flexible model has been developed to estimate the release of radionuclides from waste packages and their subsequent transport through the engineered barriers in the repository. Gradual degradation of the engineered barriers is accounted for by altering parameters at fixed time points. Safety margins of the disposal concept have been evaluated by including disturbed evolution scenarios in the analysis. 13 references, 10 figures, 2 tables

Radioactive waste repository study

International Nuclear Information System (INIS)

1978-11-01

This is the second part of a report of a preliminary study for AECL. It considers the requirements for an underground waste repository for the disposal of wastes produced by the Canadian Nuclear Fuel Program. The following topics are discussed with reference to the repository: 1) geotechnical assessment, 2) hydrogeology and waste containment, 3) thermal loading and 4) rock mechanics. (author)

Analysis on the use of engineered barriers for geologic isolation of spent fuel in a reference salt site repository

International Nuclear Information System (INIS)

Cloninger, M.O.; Cole, C.R.; Washburn, J.F.

1980-12-01

A perspective on the potential durability and effectiveness requirements for the waste form, container and other engineered barriers for geologic disposal of spent nuclear fuel has been developed. This perspective is based on calculated potential doses to individuals who may be exposed to radioactivity released from a repository via a groundwater transport pathway. These potential dose commitments were calculated with an integrated geosphere transport and bioshpere transport model. A sensitivity analysis was accomplished by varying four important system parameters, namely the waste radionuclide release rate from the repository, the delay prior to groundwater contact with the waste (leach initiation), aquifer flow velocity and flow path length. The nuclide retarding capacity of the geologic media, a major determinant of the isolation effectiveness, was not varied as a parameter but was held constant for a particular reference site. This analysis is limited to looking only at engineered barriers whose net effect is either to delay groundwater contact with the waste form or to limit the rate of release of radionuclides into the groundwater once contact has occurred. The analysis considers only leach incident scenarios, including a water well intrusion into the groundwater near a repository, but does not consider other human intrusion events or catastrophic events. The analysis has so far been applied to a reference salt site repository system and conclusions are presented.Basically, in nearly all cases, the regional geology is the most effective barrier to release of radionuclides to the biosphere; however, for long-lived isotopes of carbon, technetium and iodine, which were poorly sorbed on the geologic media, the geology is not very effective once a leach incident is initiated

GRS/ISTec strategy for the treatment of gas-related issues for repositories located in rock salt

International Nuclear Information System (INIS)

Muller-Lyda, I.; Javeri, V.; Muller, W.

2001-01-01

The treatment of gas-related issues for repositories located in rock salt by GRS and ISTec has followed a strategy which has been developed with increasing complexity and degree of detail in the past. The strategy today clearly indicates the direction to establish a comprehensive safety case and the work that remains to be done. For gas generation mainly long-term aspects are an issue to increase accuracy of predictions. Physical modelling especially for HLW is still incomplete with regard to the coupling of fluid flow with geomechanics, solution/precipitation effects and geochemistry. The appropriate tools to transform the physical models into numerical solutions are at hand in principle but have to be further developed collaterally to the physical modelling. The first full-scale demonstration of safety regarding gas issues in rock salt will have to be provided for the licensing of the Morsleben repository shut-down in the near future. (authors)

Lithomorphological aspects of northern Muria region for location candidate of the NPP radioactive wastes repository

International Nuclear Information System (INIS)

Sucipta

1995-01-01

As a part of planning and construction of NPP in the northern Muria region, a location candidate of the NPP radioactive waste repository needs to be prepared. The objective of this studywas to investigate the suitability of the geomorphologic condition of the northern Muria region for the location. The geomorphologic elements were evaluated based on the geomorphologic criteria specified by the IAEA. This study was conducted through descriptive and scoring methods for the geomorphologic elements, especially the landform and the geomorphologic processes. Based on the results of the study, the study area could be classified into three classes of suitability for the location. These are three geomorphologic units of high suitability, three units of moderate suitability and four units of low suitability. By considering the total value of the geomorphologic condition suitability and the inhibiting factors of geomorphology, three high suitability units were selected, particularly in the region of Lemahabang and Genggrengan. (author). 6 refs, 7 figs

Status of Proposed Repository for Latin-American Spent Fuel

Energy Technology Data Exchange (ETDEWEB)

Ferrada, J.J.

2004-10-04

This report compiles preliminary information that supports the premise that a repository is needed in Latin America and analyzes the nuclear situation (mainly in Argentina and Brazil) in terms of nuclear capabilities, inventories, and regional spent-fuel repositories. The report is based on several sources and summarizes (1) the nuclear capabilities in Latin America and establishes the framework for the need of a permanent repository, (2) the International Atomic Energy Agency (IAEA) approach for a regional spent-fuel repository and describes the support that international institutions are lending to this issue, (3) the current situation in Argentina in order to analyze the Argentinean willingness to find a location for a deep geological repository, and (4) the issues involved in selecting a location for the repository and identifies a potential location. This report then draws conclusions based on an analysis of this information. The focus of this report is mainly on spent fuel and does not elaborate on other radiological waste sources.

National radioactive wasterRepository Mochovce

International Nuclear Information System (INIS)

2000-01-01

In this leaflet the scheme of the Mochovce National radioactive waste repository for the Slovak Republic is presented. The National radioactive waste repository in Mochovce is a surface type storage facility. It is intended for final disposal of solid and solidified low and intermediate radioactive waste produced during the operation of nuclear power plants and institutions located within the territory of the Slovak Republic. The Repository site is situated about 2 km northwest to the Mochovce NPP

Suggested data-gathering methods for the assessment of attitudes of Nevada citizens toward location of a repository at Yucca Mountain: Final report

International Nuclear Information System (INIS)

Bradbury, J.A.

1986-12-01

The purpose of this paper is to outline a variety of methods that could be used by the Nevada Nuclear Waste Storage Investigations (NNWSI) Project to assess the attitudes of Nevada citizens toward the location of a repository at Yucca Mountain. The paper is divided into three chapters: Chapter 1 provides a background discussion; Chapter 2 discusses different social science methods and summarizes the advantages and disadvantages of each; and Chapter 3 outlines a conceptual approach to integrating several methods into one overall strategy for assessment. An assessment of the attitudes of persons who may be affected by repository activities will (1) enhance the NNWSI Project's ability to conduct the social impact assessment that can be included in an Environmental Impact Statement (EIS); (2) provide an information base for understanding and anticipating public responses; (3) allow the NNWSI Project to scope and prioritize issues that arise in the public debate that may occur over the repository location; and (4) help to facilitate communication and cooperation between the US Department of Energy (DOE) and state and local entities in the process of conducting the study. 114 refs., 1 tab

Suggested data-gathering methods for the assessment of attitudes of Nevada citizens toward location of a repository at Yucca Mountain: Final report

Energy Technology Data Exchange (ETDEWEB)

Bradbury, J A

1986-12-01

The purpose of this paper is to outline a variety of methods that could be used by the Nevada Nuclear Waste Storage Investigations (NNWSI) Project to assess the attitudes of Nevada citizens toward the location of a repository at Yucca Mountain. The paper is divided into three chapters: Chapter 1 provides a background discussion; Chapter 2 discusses different social science methods and summarizes the advantages and disadvantages of each; and Chapter 3 outlines a conceptual approach to integrating several methods into one overall strategy for assessment. An assessment of the attitudes of persons who may be affected by repository activities will (1) enhance the NNWSI Project`s ability to conduct the social impact assessment that can be included in an Environmental Impact Statement (EIS); (2) provide an information base for understanding and anticipating public responses; (3) allow the NNWSI Project to scope and prioritize issues that arise in the public debate that may occur over the repository location; and (4) help to facilitate communication and cooperation between the US Department of Energy (DOE) and state and local entities in the process of conducting the study. 114 refs., 1 tab.

Advantages of co-located spent fuel reprocessing, repository and underground reactor facilities

International Nuclear Information System (INIS)

Mahar, James M.; Kunze, Jay F.; Wes Myers, Carl; Loveland, Ryan

2007-01-01

The purpose of this work is to extend the discussion of potential advantages of the underground nuclear park (UNP) concept by making specific concept design and cost estimate comparisons for both present Generation III types of reactors and for some of the modular Gen IV or the GNEP modular concept. For the present Gen III types, we propose co-locating reprocessing and (re)fabrication facilities along with disposal facilities in the underground park. The goal is to determine the site costs and facility construction costs of such a complex which incorporates the advantages of a closed fuel cycle, nuclear waste repository, and ultimate decommissioning activities all within the UNP. Modular power generation units are also well-suited for placement underground and have the added advantage of construction using current and future tunnel boring machine technology. (authors)

Childhood vesicoureteral reflux studies: registries and repositories sources and nosology.

Science.gov (United States)

Chesney, Russell W; Patters, Andrea B

2013-12-01

Despite several recent studies, the advisability of antimicrobial prophylaxis and certain imaging studies for urinary tract infections (UTIs) remains controversial. The role of vesicoureteral reflux (VUR) on the severity and re-infection rates for UTIs is also difficult to assess. Registries and repositories of data and biomaterials from clinical studies in children with VUR are valuable. Disease registries are collections of secondary data related to patients with a specific diagnosis, condition or procedure. Registries differ from indices in that they contain more extensive data. A research repository is an entity that receives, stores, processes and/or disseminates specimens (or other materials) as needed. It encompasses the physical location as well as the full range of activities associated with its operation. It may also be referred to as a biorepository. This report provides information about some current registries and repositories that include data and samples from children with VUR. It also describes the heterogeneous nature of the subjects, as some registries and repositories include only data or samples from patients with primary reflux while others also include those from patients with syndromic or secondary reflux. Copyright © 2012 Journal of Pediatric Urology Company. All rights reserved.

Shaft placement in a bedded salt repository

International Nuclear Information System (INIS)

Klasi, M.L.

1982-10-01

Preferred shaft pillar sizes and shaft locations were determined with respect to the induced thermal stresses in a generic bedded salt repository at a depth of 610 m with a gross thermal loading of 14.8 W/m 2 . The model assumes isotropic material properties, plane strain and linear elastic behavior. Various shaft locations were analyzed over a 25 year period. The thermal results show that for this time span, the stratigraphy is unimportant except for the region immediately adjacent to the repository. The thermomechanical results show that for the given repository depth of 610 m, a minimum central shaft pillar radius of 244 m is required to equal the material strength in the barrier pillar. An assumed constant stress and constant temperature distribution creep model of the central shaft region adjacent to the repository conservatively overestimates a creep closure of 310 mm in a 6.1 m diameter centrally-located shaft

Cross Institutional Cooperation on a Shared Bit Repository

DEFF Research Database (Denmark)

Zierau, Eld; Kejser, Ulla Bøgvad

2013-01-01

This paper explores how independent institutions, such as archives and libraries, can cooperate on managing a shared bit repository with bit preservation, in order to use their resources for preservation in a more cost-effective way. It uses the OAIS Reference Model to provide a framework...... for systematically analysing institutions technical and organisational requirements for a remote bit repository. Instead of viewing a bit repository simply as Archival Storage for the institutions repositories, we argue for viewing it as consisting of a subset of functions from all entities defined by the OAIS...... Reference Model. The work is motivated by and used in a current Danish feasibility study for establishing a national bit repository. The study revealed that depending on their missions and the collections they hold, the institutions have varying requirements e.g. for bit safety, accessibility...

Cross Institutional Cooperation on a Shared Bit Repository

DEFF Research Database (Denmark)

Zierau, Eld; Kejser, Ulla Bøgvad

2010-01-01

This paper explores how independent institutions, such as archives and libraries, can cooperate on managing a shared bit repository with bit preservation in order to use their resources for preservation n in a more cost-effective way. It uses the OAIS Reference Model to provide a framework...... for systematically analysing the technical and organizational requirements of institutions for a remote bit repository. Instead of viewing a bit repository simply as Archival Storage for the institutions’ repositories, we argue for viewing it as consisting of a subset of functions from all entities defined...... by the OAIS Reference Model. The work is motivated by and used in a current Danish feasibility study for establishing a national bit repository. The study revealed that depending on their missions and the collections they hold, the institutions have varying requirements, such as for bit safety, accessibility...

Modelling saline intrusion for repository performance assessment

International Nuclear Information System (INIS)

Jackson, C.P.

1989-04-01

UK Nirex Ltd are currently considering the possibility of disposal of radioactive waste by burial in deep underground repositories. The natural pathway for radionuclides from such a repository to return to Man's immediate environment (the biosphere) is via groundwater. Thus analyses of the groundwater flow in the neighbourhood of a possible repository, and consequent radionuclide transport form an important part of a performance assessment for a repository. Some of the areas in the UK that might be considered as possible locations for a repository are near the coast. If a repository is located in a coastal region seawater may intrude into the groundwater flow system. As seawater is denser than fresh water buoyancy forces acting on the intruding saline water may have significant effects on the groundwater flow system, and consequently on the time for radionuclides to return to the biosphere. Further, the chemistry of the repository near-field may be strongly influenced by the salinity of the groundwater. It is therefore important for Nirex to have a capability for reliably modelling saline intrusion to an appropriate degree of accuracy in order to make performance assessments for a repository in a coastal region. This report describes work undertaken in the Nirex Research programme to provide such a capability. (author)

Nuclear waste repository siting and locational conflict analysis: A contextual approach

International Nuclear Information System (INIS)

Murauskas, G.T.

1989-01-01

This study develops and evaluates an alternative framework that is based on contextual variables. The premise is that differences in attitudes and perceptions regarding the local siting of nuclear wastes and differences in attitudes regarding siting decision-making procedures are influenced by local political, economic, and cultural variables. This framework articulates the nature of conflict in terms of the incongruence between the use-value individuals ascribe to their present situation and the anticipated exchange-value individuals associate with the local siting of a nuclear waste repository. In order to evaluate this conceptual framework a survey was conducted of residents in four communities representing distinct societal contexts: Richton, Mississippi; Peterborough, New Hampshire; Richland, Washington; and Antigo/Waupaca, Wisconsin. Data analyses indicate substantial differences in economic expectations associated with the local siting of a high-level nuclear waste repository and in perception regarding the impacts such a repository might have on the environment, local agriculture, personal health and safety, and the quality of life

Radioactive waste repository study

International Nuclear Information System (INIS)

1978-11-01

This is the first part of a report of a preliminary study for Atomic Energy of Canada Limited. It considers the requirements for an underground waste repository for the disposal of wastes produced by the Canadian Nuclear Fuel Program. The following topics are discussed with reference to the repository: 1) underground layout, 2) cost estimates, 3) waste handling, 4) retrievability, decommissioning, sealing and monitoring, and 5) research and design engineering requirements. (author)

International perspective on repositories for low level waste

International Nuclear Information System (INIS)

Bergstroem, Ulla; Pers, Karin; Almen, Ylva

2011-12-01

Nuclear energy production gives rise to different types of radioactive waste. The use of nuclear isotopes within the research, industry and medical sectors also generates radioactive waste. To protect man and the environment from radiation the waste is isolated and contained by deposition in repositories. These repositories may have various designs regarding location, barriers etc depending on the potential danger of the waste. In Sweden, low- and intermediate level waste (LILW) is disposed of in the SFR repository in Forsmark. The repository is located 60 metres down into the bedrock under the bottom of the sea and covered by 6 metres of water. It is planned to extend SFR to accommodate decommissioning waste from the dismantling of the Swedish nuclear power facilities and also for the additional operation waste caused by the planned prolonged operation time. When planning the extension consultations will be carried out with the host municipality, authorities, organisations and general public. In planning the extension, SKB has performed a worldwide compilation of how other countries have, or plan to, handle the final disposal of similar wastes. The aim of this report is to give a brief description of LILW repositories worldwide; including general brief descriptions of many facilities, descriptions of the waste and the barriers as well as safety assessments for a few chosen repositories which represent different designs. The latter is performed, where possible, to compare certain features against the Swedish SFR. To provide a background and context to this study, international organisations and conventions are also presented along with internationally accepted principles regarding the management of radioactive waste. Similar to SFR, suitable locations for the repositories have, in many countries, been found at sites that already have, or used to have nuclear activities, such as reactor sites. Abandoned and disused mines, such as the salt mines in Germany, also

International perspective on repositories for low level waste

Energy Technology Data Exchange (ETDEWEB)

Bergstroem, Ulla; Pers, Karin; Almen, Ylva (SKB International AB (Sweden))

2011-12-15

Nuclear energy production gives rise to different types of radioactive waste. The use of nuclear isotopes within the research, industry and medical sectors also generates radioactive waste. To protect man and the environment from radiation the waste is isolated and contained by deposition in repositories. These repositories may have various designs regarding location, barriers etc depending on the potential danger of the waste. In Sweden, low- and intermediate level waste (LILW) is disposed of in the SFR repository in Forsmark. The repository is located 60 metres down into the bedrock under the bottom of the sea and covered by 6 metres of water. It is planned to extend SFR to accommodate decommissioning waste from the dismantling of the Swedish nuclear power facilities and also for the additional operation waste caused by the planned prolonged operation time. When planning the extension consultations will be carried out with the host municipality, authorities, organisations and general public. In planning the extension, SKB has performed a worldwide compilation of how other countries have, or plan to, handle the final disposal of similar wastes. The aim of this report is to give a brief description of LILW repositories worldwide; including general brief descriptions of many facilities, descriptions of the waste and the barriers as well as safety assessments for a few chosen repositories which represent different designs. The latter is performed, where possible, to compare certain features against the Swedish SFR. To provide a background and context to this study, international organisations and conventions are also presented along with internationally accepted principles regarding the management of radioactive waste. Similar to SFR, suitable locations for the repositories have, in many countries, been found at sites that already have, or used to have nuclear activities, such as reactor sites. Abandoned and disused mines, such as the salt mines in Germany, also

Geohydrology surrounding a potential high-level nuclear waste repository in the Paradox Basin, Utah

International Nuclear Information System (INIS)

Brandstetter, A.; Kroitoru, L.; Andrews, R.W.; Thackston, J.W.

1984-01-01

The Gibson Dome area in the Paradox Basin in southeastern Utah has been identified as a potential location for a high-level nuclear waste repository on the basis of an adequate thickness of bedded salt formations at desirable depths, suitable topography for surface facilities, few known archaeological sites, less resource potential than otherwise similar areas, and long-term geologic and tectonic stability. The area appears also suitable from a geohydrologic viewpoint, on the basis of data collected and analyses performed to date. The upper, near-surface, geologic formations include both regionally continuous water-bearing formations and locally perched ground waters that discharge into nearby surface streams and into the Colorado River. Below the Paradox salts, the formations of interest with respect to repository safety include regionally continuous water-bearing formations, with the Leadville limestone being the principal water-transmitting unit. Flows in all water-bearing formations are essentially horizontal. If a vertical connection were established through a potential repository, hydraulic gradients indicate that the flow would first be downward from the upper to the lower formations and then laterally, principally in the Leadville formation. There are some indications that minor leakage could occur into the Colorado River as close as Cataract Canyon, about 20 to 25 km (10 to 15 miles) from a potential repository location in Davis Canyon, or into the Colorado River in Marble Canyon (Arizona), about 240 km (150 miles) to the southwest. Groundwater flow from a repository to these locations is unlikely, however, since water would first have to penetrate the essentially impermeable salt layers before it would reach the Leadville formation. 11 references, 4 figures

Assessment of disruptive scenarios of a Canadian used fuel repository in crystalline rock

Energy Technology Data Exchange (ETDEWEB)

Gobien, M.; Garisto, F.; Hunt, N.; Kremer, E.P. [Nuclear Waste Management Organization (NWMO), Toronto, Ontario (Canada)

2015-06-15

The NWMO has recently extended its modelling capabilities by performing simulations for four disruptive scenarios that, to date, have not yet been examined in detail. These scenarios complement those considered in an existing postclosure safety assessment for a conceptual geological repository located in a hypothetical crystalline rock formation. The four new disruptive scenarios are: Shaft Seal Failure, Undetected Fault, Open or Poorly Sealed Borehole and Open Borehole Due to Inadvertent Human Intrusion. All simulations are based on the FRAC3DVS-OPG Site-Scale Model. The Site-Scale Model includes a simplified representation of the full repository and a portion of the surrounding sub-regional flow system. All transport simulations are performed with only the radionuclide I-129. Transport rates to the surface and a domestic water supply well are compared to the Reference Case results from an earlier case study documented in Reference. (author)

Assessment of disruptive scenarios of a Canadian used fuel repository in crystalline rock

Energy Technology Data Exchange (ETDEWEB)

Gobien, M.; Garisto, F.; Hunt, N.; Kremer, E.P., E-mail: mgobien@nwmo.ca [Nuclear Waste Management Organization, Toronto, ON (Canada)

2015-07-01

The NWMO has recently extended its modelling capabilities by performing simulations for four disruptive scenarios that, to date, have not yet been examined in detail. These scenarios complement those considered in an existing postclosure safety assessment for a conceptual geological repository located in a hypothetical crystalline rock formation. The four new disruptive scenarios are: Shaft Seal Failure, Undetected Fault, Open or Poorly Sealed Borehole and Open Borehole Due to Inadvertent Human Intrusion. All simulations are based on the FRAC3DVS-OPG [1] Site-Scale Model [2]. The Site-Scale Model includes a simplified representation of the full repository and a portion of the surrounding sub-regional flow system. All transport simulations are performed with only the radionuclide I-129. Transport rates to the surface and a domestic water supply well are compared to the Reference Case results from an earlier case study documented in Reference [2]. (author)

Assessment of disruptive scenarios of a Canadian used fuel repository in crystalline rock

International Nuclear Information System (INIS)

Gobien, M.; Garisto, F.; Hunt, N.; Kremer, E.P.

2015-01-01

The NWMO has recently extended its modelling capabilities by performing simulations for four disruptive scenarios that, to date, have not yet been examined in detail. These scenarios complement those considered in an existing postclosure safety assessment for a conceptual geological repository located in a hypothetical crystalline rock formation. The four new disruptive scenarios are: Shaft Seal Failure, Undetected Fault, Open or Poorly Sealed Borehole and Open Borehole Due to Inadvertent Human Intrusion. All simulations are based on the FRAC3DVS-OPG [1] Site-Scale Model [2]. The Site-Scale Model includes a simplified representation of the full repository and a portion of the surrounding sub-regional flow system. All transport simulations are performed with only the radionuclide I-129. Transport rates to the surface and a domestic water supply well are compared to the Reference Case results from an earlier case study documented in Reference [2]. (author)

Durability of cemented waste in repository and under simulated conditions

International Nuclear Information System (INIS)

Dragolici, F.; Nicu, M.; Lungu, L.; Turcanu, C.; Rotarescu, Gh.

2000-01-01

simulated disposal conditions for reference samples; - emplacement of reference samples in Baita Bihor Repository for real disposal characterization. All samples were positioned in five locations of Baita-Bihor repository where they will be kept for 1, 3, 5 and 10 years before mechanical and structural characterization. These locations have different humidity values, decreasing from location 1 to 5. The results will be compared with those obtained for the same type of samples kept in laboratory conditions. The mechanical performances of the matrix with cement-mineral additives are not influenced if bentonite or volcanic tuff concentration is is lower than 10%. The very good mechanical behaviour of the samples, drives at the conclusion that the additive cement-mineral mixture could be used in the disposal procedure, with good results, if the future structure characterization would prove the role as engineered barrier. Complexing reagents reduce drastically the mechanical performances. The chemical nature of the complexing agent plays an important role, the damaging effect being more pregnant for tartaric and citric acid than for oxalic acid. In any case there is a maximum limit of concentration which is acceptable from mechanical point of view. The mechanical resistance observed in all samples, after one year disposal, are within the accepted limits for the matrix durability. Thus, disposal conditions has not influence the mechanical properties of the cement matrix after one year disposal. The presented results, showed that bentonite seems to have a positive influence on the quality of the examined matrices . These results are preliminary. The data obtained so far will be completed with those to be obtained after three year disposal. XRD initial investigation of waste samples showed complex changes in the structure and components. To understand the systems, series of different compositions need to be characterized. In the next years the durability of samples kept for times

Methods for definition of reference conditions for a repository site taking long-term environmental change into account

Energy Technology Data Exchange (ETDEWEB)

Ikonen, A.T.K. [Environmental Research and Assessment EnviroCase, Ltd. (Finland)

2014-07-01

In a few countries, programmes for disposal of spent nuclear fuel have proceeded into a site-specific phase, and the number of low- and intermediate-level nuclear waste repositories requiring updated state-of-the-art long-term safety assessments is considerable. In this contribution, the approach employed in the Finnish spent fuel disposal programme is analysed and used as an example for a more general methodology for defining reference surface conditions for a site, e.g. to guide selection of representative input data to safety assessments, using spatio-temporal analogues so that long-term environmental changes are taken into account. The contribution incorporates also elements from discussions in the IAEA EMRAS II and MODARIA working groups on addressing the environmental change in the assessments. The legacy of the earlier BIOMASS project is also recognised. Broadly, the methods to be presented include identification of similarity factors (e.g. geological, biological and climate regimes) upon which a reference area can be delineated. Within the reference area, characteristic lines of development and biotopes are identified and described, and these are then used to guide further research and application of literature data to iteratively accumulate adequate understanding of the site conditions and relevant processes at the present and in the future (by projecting further the past and present development lines and biotopes). In this iterative approach, also the intensity of research efforts can be adjusted with the stage of the repository programme, as will be discussed in the complete contribution. Document available in abstract form only. (authors)

Ventilation planning for a prospective nuclear waste repository

International Nuclear Information System (INIS)

Wallace, K.G. Jr.

1987-01-01

In 1982, the US Congress passed the Nuclear Waste Policy Act to provide for the development of underground repositories for spent nuclear fuel. This development will be managed by the United States Department of Energy. In 1986, the President selected three areas for site characterization to determine their suitability for the development of an underground repository; those sites were: (1) A site in volcanic tuff located at Yucca Mountain in Nevada, (2) a site in bedded salt located in Deaf Smith County in Texas, and (3) a site in basalt located in Hanford, Washington. At present conceptual repository designs are being developed for each site. A key element of a repository design is the underground ventilation system required to support construction, nuclear waste emplacement, and potential waste retrieval. This paper describes the preliminary ventilation systems designed for the repository in tuff. The concept provides separate ventilation systems for the construction and waste emplacement activities. The paper further describes the means by which acceptable environmental conditions will be re-established to allow re-entry into previously closed rooms for the purpose of inspection, maintenance or retrieval

Deep repository for long-lived low- and intermediate-level waste. Preliminary safety assessment

International Nuclear Information System (INIS)

1999-11-01

A preliminary safety assessment has been performed of a deep repository for long-lived low- and intermediate-level waste, SFL 3-5. The purpose of the study is to investigate the capacity of the facility to act as a barrier to the release of radionuclides and toxic pollutants, and to shed light on the importance of the location of the repository site. A safety assessment (SR 97) of a deep repository for spent fuel has been carried out at the same time. In SR 97, three hypothetical repository sites have been selected for study. These sites exhibit fairly different conditions in terms of hydrogeology, hydrochemistry and ecosystems. To make use of information and data from the SR 97 study, we have assumed that SFL 3-5 is co-sited with the deep repository for spent fuel. A conceivable alternative is to site SFL 3-5 as a completely separate repository. The focus of the SFL 3-5 study is a quantitative analysis of the environmental impact for a reference scenario, while other scenarios are discussed and analyzed in more general terms. Migration in the repository's near- and far-field has been taken into account in the reference scenario. Environmental impact on the three sites has also been calculated. The calculations are based on an updated forecast of the waste to be disposed of in SFL 3-5. The forecast includes radionuclide content, toxic metals and other substances that have a bearing on a safety assessment. The safety assessment shows how important the site is for safety. Two factors stand out as being particularly important: the water flow at the depth in the rock where the repository is built, and the ecosystem in the areas on the ground surface where releases may take place in the future. Another conclusion is that radionuclides that are highly mobile and long-lived, such as 36 Cl and 93 Mo , are important to take into consideration. Their being long-lived means that barriers and the ecosystems must be regarded with a very long time horizon

Conceptual designs for waste packages for horizontal or vertical emplacement in a repository in salt for reference in the site characterization plan

International Nuclear Information System (INIS)

1987-06-01

This report includes the options of horizontal and vertical emplacement, the addition of a phased repository, an additional waste form (intact spent fuel), revised geotechnical data appropriate for the Deaf Smith County site, new corrosion data for the container, and new repository design data. The waste package consists of waste form and canister within a thick-walled, low-carbon steel container surrounded by packing. The container is a hollow cylinder with a flat head welded to each end. The design concepts for the waste container or vertical and horizontal emplacement are identical. This report discusses the results of analyses of aspects of the reference waste package concept needing changes because of new data and information believed applicable to the Deaf Smith County site. Included are waste package conceptual designs or (1) the reference defense high-level waste form from the Savannah River Plant; (2) intact spent fuel with our pressurized-water-reactor or nine boiling-water-reactor assemblies per package for emplacement during Phase 1 of repository operation; and (3) spent fuel which has been disassembled and consolidated into a segmented cylindrical canister with rods from either 12 pressurized-water-reactor or 30 boiling-water-reactor assemblies per package for emplacement during Phase 2. 30 refs., 61 figs., 30 tabs

NIA Aging Cell Repository

Data.gov (United States)

Federal Laboratory Consortium — To facilitate aging research on cells in culture, the NIA provides support for the NIA Aging Cell Repository, located at the Coriell Institute for Medical Research...

Radioactive waste isolation in salt: peer review of Westinghouse Electric Corporation's report on reference conceptual designs for a repository waste package

International Nuclear Information System (INIS)

Rote, D.M.; Hull, A.B.; Was, G.S.; Macdonald, D.D.; Wilde, B.E.; Russell, J.E.; Kruger, J.; Harrison, W.; Hambley, D.F.

1985-10-01

This report documents the findings of the peer panel constituted by Argonne National Laboratory to review Region A of Westinghouse Electric Corporation's report entitled Waste Package Reference Conceptual Designs for a Repository in Salt. The panel determined that the reviewed report does not provide reasonable assurance that US Nuclear Regulatory Commission (NRC) requirements for waste packages will be met by the proposed design. It also found that it is premature to call the design a ''reference design,'' or even a ''reference conceptual design.'' This review report provides guidance for the preparation of a more acceptable design document

Coupling fuel cycles with repositories: how repository institutional choices may impact fuel cycle design

International Nuclear Information System (INIS)

Forsberg, C.; Miller, W.F.

2013-01-01

The historical repository siting strategy in the United States has been a top-down approach driven by federal government decision making but it has been a failure. This policy has led to dispatching fuel cycle facilities in different states. The U.S. government is now considering an alternative repository siting strategy based on voluntary agreements with state governments. If that occurs, state governments become key decision makers. They have different priorities. Those priorities may change the characteristics of the repository and the fuel cycle. State government priorities, when considering hosting a repository, are safety, financial incentives and jobs. It follows that states will demand that a repository be the center of the back end of the fuel cycle as a condition of hosting it. For example, states will push for collocation of transportation services, safeguards training, and navy/private SNF (Spent Nuclear Fuel) inspection at the repository site. Such activities would more than double local employment relative to what was planned for the Yucca Mountain-type repository. States may demand (1) the right to take future title of the SNF so if recycle became economic the reprocessing plant would be built at the repository site and (2) the right of a certain fraction of the repository capacity for foreign SNF. That would open the future option of leasing of fuel to foreign utilities with disposal of the SNF in the repository but with the state-government condition that the front-end fuel-cycle enrichment and fuel fabrication facilities be located in that state

Socioeconomic impacts of large-scale developments: implications for high-level nuclear waste repositories

International Nuclear Information System (INIS)

Murdock, S.H.; Leistritz, F.L.; Hamm, R.R.

1983-01-01

High-level nuclear waste repositories will likely be located in sparsely settled rural areas in the US. These projects will significantly affect the economic, demographic, public service, fiscal, and social (the socioeconomic) dimensions of those rural areas. The impacts and means of mitigating them thus require careful analysis. This paper examines some of the potential socioeconomic impacts likely to occur in rural areas as a result of repository siting and development, and it describes some of the characteristics of mitigation programs that are likely to be necessary, if the impacts are to be addressed. Both (1) standard impacts, those resulting from the fact that, like many other large-scale developments, repositories will involve a substantial number of new workers and residents (relative to the size of existing communities), and (2) special impacts, those resulting from the fact that repositories store radioactive materials, are examined. The discussion indicates that economic, demographic, public service, fiscal, and social impacts (standard and special) of these repositories will be substantial and problematic in many cases. Unless the impacts are effectively addressed with carefully planned and well financed mitigation efforts that insure that high-quality planning information is provided to local residents, and that local residents are involved in impact planning and management throughout the siting and development process, repository siting is unlikely to be effectively and equitably achieved. 44 references

Location Is Everything: The Use and Marketing of Reference E-Mail

Science.gov (United States)

Collins, Susan L.

2006-01-01

Reference e-mail continues to be a vital reference service. This article studies the trends in reference e-mail use over an eight year period. Usage statistics are analyzed particularly in light of the marketing of the service via changes in the location of the service on the official university libraries' Web pages. Included are recommendations…

Comparison of potential radiological consequences from a spent-fuel repository and natural uranium deposits

International Nuclear Information System (INIS)

Wick, O.J.; Cloninger, M.O.

1980-09-01

A general criterion has been suggested for deep geological repositories containing spent fuel - the repositories should impose no greater radiological risk than due to naturally occurring uranium deposits. The following analysis investigates the rationale of that suggestion and determines whether current expectations of spent-fuel repository performance are consistent with such a criterion. In this study, reference spent-fuel repositories were compared to natural uranium-ore deposits. Comparisons were based on intrinsic characteristics, such as radionuclide inventory, depth, proximity to aquifers, and regional distribution, and actual and potential radiological consequences that are now occurring from some ore deposits and that may eventually occur from repositories and other ore deposits. The comparison results show that the repositories are quite comparable to the natural ore deposits and, in some cases, present less radiological hazard than their natural counterparts. On the basis of the first comparison, placing spent fuel in a deep geologic repository apparently reduces the hazard from natural radioactive materials occurring in the earth's crust by locating the waste in impermeable strata without access to oxidizing conditions. On the basis of the second comparison, a repository constructed within reasonable constraints presents no greater hazard than a large ore deposit. It is recommended that if the naturally radioactive environment is to be used as a basis for a criterion regarding repositories, then this criterion should be carefully constructed. The criterion should be based on the radiological quality of the waters in the immediate region of a specific repository, and it should be in terms of an acceptable potential increase in the radiological content of those waters due to the existence of the repository

Environmental assessment: Reference repository location, Hanford Site, Washington

International Nuclear Information System (INIS)

1986-05-01

This appendix responds to the issues raised by Federal, State, and local governments, affected Indian Tribes, private citizens, and other organizations on the draft environmental assessment (EA) that was prepared pursuant to Section 112 of the Nuclear Waste Policy Act of 1982. In addition to presenting the issues raised in the comments and the responses, it describes where changes were made in the final EA. 535 refs., 13 figs., 16 tabs

Flooding studies of proposed repository locations in the Palo Duro Basin of the Texas Panhandle

International Nuclear Information System (INIS)

1985-04-01

This report contains the results of flooding studies of those stream channels that drain the proposed locations of a high-level nuclear-waste repository in Deaf Smith and Swisher Counties, Texas. Included are computations of the flood hydrographs and water surface profiles of the 100-year, 500-year, and probable maximum floods for Palo Duro Creek, Tule Creek, and Pleasant Draw. The hydrographs were produced according to the method of the Soil Conservation Service for ungaged watersheds, and the computations were made with computer programs developed by the US Army Corps of Engineers. The flood hydrographs were computed with the HEC-1 Flood Hydrograph Package and the water surface elevations with the HEC-2 Water Surface Profiles program. 76 refs., 19 figs., 16 tabs

A geotechnical evaluation of potentially acceptable sites for a high-level nuclear waste repository near the Red Lake Indian Reservation

International Nuclear Information System (INIS)

1986-01-01

The scope and work which served as the basis for this report included the following major activities; (1) A review and summary of the screening methodologies utilized by DOE for the selection of proposed nuclear waste repository sites, including a description of the inherent weakness in those methodologies. (2) A description of the geologic and hydrologic features of the rock bodies selected by DOE and an identification of those features which could result in hazardous conditions as a result of the location of a high-level nuclear waste repository. (3) An assessment of potential environmental impacts of the repository and discussion of endanged species in the proposed repository project areas. This report is organized in three major sections in relationship to the scope of work. A list of references is also included at the end of this report. 37 refs., 2 figs

Deep repository for long-lived low- and intermediate-level waste. Preliminary safety assessment

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-11-01

A preliminary safety assessment has been performed of a deep repository for long-lived low- and intermediate-level waste, SFL 3-5. The purpose of the study is to investigate the capacity of the facility to act as a barrier to the release of radionuclides and toxic pollutants, and to shed light on the importance of the location of the repository site. A safety assessment (SR 97) of a deep repository for spent fuel has been carried out at the same time. In SR 97, three hypothetical repository sites have been selected for study. These sites exhibit fairly different conditions in terms of hydrogeology, hydrochemistry and ecosystems. To make use of information and data from the SR 97 study, we have assumed that SFL 3-5 is co-sited with the deep repository for spent fuel. A conceivable alternative is to site SFL 3-5 as a completely separate repository. The focus of the SFL 3-5 study is a quantitative analysis of the environmental impact for a reference scenario, while other scenarios are discussed and analyzed in more general terms. Migration in the repository's near- and far-field has been taken into account in the reference scenario. Environmental impact on the three sites has also been calculated. The calculations are based on an updated forecast of the waste to be disposed of in SFL 3-5. The forecast includes radionuclide content, toxic metals and other substances that have a bearing on a safety assessment. The safety assessment shows how important the site is for safety. Two factors stand out as being particularly important: the water flow at the depth in the rock where the repository is built, and the ecosystem in the areas on the ground surface where releases may take place in the future. Another conclusion is that radionuclides that are highly mobile and long-lived, such as {sup 36}Cl and {sup 93}Mo , are important to take into consideration. Their being long-lived means that barriers and the ecosystems must be regarded with a very long time horizon.

Oxidation-reduction reactions. Overview and implications for repository studies

International Nuclear Information System (INIS)

Apted, Michael J.; Arthur, Randolph C.; Sasamoto, Hiroshi; Yui, Mikazu; Iwatsuki, Teruki

2001-02-01

The purpose of this report is to provide a survey and review on oxidation-reduction ('redox') reactions, with particular emphasis on implications for disposal of high-level waste (HLW) in deep geological formations. As an overview, the focus is on basic principles, problems, and proposed research related specifically to the assessment of redox for a HLW repository in Japan. For a more comprehensive treatment of redox and the myriad associated issues, the reader is directed to the cited textbooks used as primary references in this report. Low redox conditions in deep geological formations is a key assumption in the 'Second Progress Report on Research and Development for the Geological Disposal of HLW in Japan' (hereafter called H12'). The release behavior of multi-valent radioelements (e.g., Tc, Se, U, Pu, Np), as well as daughter radioelements of these radioelements, from a deep geological repository are sensitively related to redox conditions. Furthermore, the performance of certain barrier materials, such as overpack and buffer, may be impacted by redox conditions. Given this importance, this report summarizes some key topics for future technical studies supporting site characterization and repository performance as follows: To fully test the conceptual models for system Eh, it will be necessary to measure and evaluate trace element and isotopic information of both coexisting groundwater and reactive minerals of candidate rocks. Because of importance of volatile species (e.g., O 2 , H 2 etc.) in redox reactions, and given the high total pressure of a repository located 500 to 1000 meter deep, laboratory investigations of redox will necessarily require use of pressurized test devices that can fully simulate repository conditions. The stability (redox capacity) of the repository system with respect to potential changes in redox boundary condition induced by oxidizing waters intrusion should be established experimentally. An overall conceptual model that unifies

National radioactive waste repository draft EIS. 2 volumes

International Nuclear Information System (INIS)

2002-01-01

Most Australians benefit either directly or indirectly from the medical, industrial and scientific use of radioactive materials. This use produces a small amount of radioactive waste, including low level and short-lived intermediate level radioactive waste such as lightly contaminated soil, plastic, paper, laboratory equipment, smoke detectors, exit signs and gauges.This waste is temporarily stored at more than 100 urban and rural locations around Australia, much of it in buildings that were neither designed nor located for the long-term storage of radioactive material and that are nearing or have reached capacity. Storage locations include hospitals, research institutions, and industry and government stores. Storing such waste in many locations in non-purpose built facilities potentially poses greater risk to the environment and people than disposing of the material in a national, purpose-built repository where the material can be safely managed and monitored. The objectives of the national repository are to: 1. strengthen Australia's radioactive waste management arrangements by promoting the safe and environmentally sound management of low level and short-lived intermediate level radioactive waste 2. provide safe containment of these wastes until the radioactivity has decayed to background levels. To meet these objectives, it is proposed to construct a national near-surface repository at either the preferred site on the Woomera Prohibited Area (WPA) or either of the two nearby alternative sites. The facility is not intended for the disposal of radioactive ores from mining. A national store for long-lived intermediate level waste will not be co-located with the national repository, and would be subject to a separate environmental assessment process.One preferred and two alternative sites have been selected for the national repository, following an extensive site selection process. All three sites are located in northern South Australia in a region known as central

From the repository to the deep geological repository - and back to the Terrain surface?

International Nuclear Information System (INIS)

Lahodynsky, R.

2011-01-01

How deep is 'safe'? How long is long-term? How and for how long will something be isolated? Which rock, which formation and which location are suitable? A repository constructed for the safekeeping of radioactive or highly toxic wastes can be erected either on the surface, near the surface or underground. Radioactive waste is currently often stored at near-surface locations. The storage usually takes place nearby of a nuclear power plant in pits or concrete tombs (vaults). However, repositories can also be found in restricted areas, e.g. near nuclear weapon production or reprocessing plants (WAA) or nuclear weapons test sites (including Tomsk, Russia, Hanford and Nevada desert, USA), or in extremely low rainfall regions (South Africa). In addition there are disused mines which are now used as underground repositories. Low-level and medium-active (SMA) but also high-level waste (HAA) are stored at these types of sites (NPP, WAA, test areas, former mines). In Russia (Tomsk, Siberia) liquid radioactive waste has been injected into deep geological formations for some time (Minatom, 2001). However, all these locations are not the result of a systematic, scientific search or a holistic process for finding a location, but the result of political decisions, sometimes ignoring scientific findings. Why underground storage is given preference over high-security landfill sites (HSD) often has economic reasons. While a low safety standard can significantly reduce the cost of an above-ground high-security landfill as a waste disposal depot, spending remains high, especially due to the need for capital formation to cover operating expenses after filling the HSD. In the case of underground storage, on the other hand, no additional expenses are required for the period after backfilling. The assumption of lower costs for a deep repository runs through the past decades and coincides with the assumption that the desired ideal underground conditions actually exist and will

Safety-relevant assessment concerning the proposals for investigations in proposed locations for stage 3 of the deep geological repositories project; Sicherheitstechnisches Gutachten zum Vorschlag der in Etappe 3 SGT weiter zu untersuchenden geologischen Standortgebiete - Sachplan geologische Tiefenlager, Etappe 2

Energy Technology Data Exchange (ETDEWEB)

NONE

2017-04-15

This comprehensive report published by the Swiss Federal Nuclear Safety Inspectorate ENSI examines the proposals made by the Swiss National Cooperative for the disposal of Radioactive Waste (NAGRA) concerning proposed locations for deep waste repositories. Important basic considerations to be made when narrowing down the choice of host rock types and the selection of possible locations are discussed. These include, amongst others, safety concepts for the repositories, geological models and technical feasibility of repositories in Opalinus Clay, Brown Dogger layers and marl. The properties of various host rocks are discussed. Methods to be used in choosing at least two possible sites for repositories are considered. Also, the radioactive dosage to be expected at the various sites proposed is discussed. A safety-relevant comparison of the sites is made and an overall assessment is presented. The locations proposed for surface facilities at three proposed locations are discussed. The report is completed with an appendix containing tables and a list of relevant expert reports.

VHA Data Sharing Agreement Repository

Data.gov (United States)

Department of Veterans Affairs — The VHA Data Sharing Agreement Repository serves as a centralized location to collect and report on agreements that share VHA data with entities outside of VA. It...

Public involvement in the siting of contentious facilities; Lessons from the radioactive waste repository siting programmes in Canada and the United States, with special reference to the Swedish repository siting process

International Nuclear Information System (INIS)

Richardson, P.J.

1997-08-01

This report describes the conclusion of a two-part programme, begun in 1994 with the overall aim of assisting in the development of an acceptable public participation strategy for use in Sweden for the siting of contentious facilities, with particular reference to the ongoing siting programme for a deep repository for spent nuclear fuel. The first part of the work programme, a global review of siting practice, was reported as SSI Rapport 94-15, in November 1994. This recommended further detailed studies of at least two individual programmes, which have now been carried out in Canada and the United States, and are reported on here. They involved face to face meetings with many of the main stake holders in the two programmes and enabled valuable insight to be gained into the potential problems associated with increased public participation, as well as identifying good practice where it exists. The lessons learned have then been applied to the evolving repository siting process in Sweden. 35 refs

Public involvement in the siting of contentious facilities; Lessons from the radioactive waste repository siting programmes in Canada and the United States, with special reference to the Swedish repository siting process

Energy Technology Data Exchange (ETDEWEB)

Richardson, P J [Geosciences for Development and the Environment (United Kingdom)

1997-08-01

This report describes the conclusion of a two-part programme, begun in 1994 with the overall aim of assisting in the development of an acceptable public participation strategy for use in Sweden for the siting of contentious facilities, with particular reference to the ongoing siting programme for a deep repository for spent nuclear fuel. The first part of the work programme, a global review of siting practice, was reported as SSI Rapport 94-15, in November 1994. This recommended further detailed studies of at least two individual programmes, which have now been carried out in Canada and the United States, and are reported on here. They involved face to face meetings with many of the main stake holders in the two programmes and enabled valuable insight to be gained into the potential problems associated with increased public participation, as well as identifying good practice where it exists. The lessons learned have then been applied to the evolving repository siting process in Sweden. 35 refs.

Environmental issues of repository licensing: an evaluation of a hypothetical high-level radioactive waste repository

International Nuclear Information System (INIS)

Owen, J.L.; McGinnis, J.T.; Harper, C.M.; Battelle Columbus Labs., OH)

1982-01-01

This paper presents results of an environmental assessment conducted under the direction of the Office of Nuclear Waste Isolation as part of the National Waste Terminal Storage program. The study defined a range of potential environmental effects of constructing, operating, decommissioning, and long-term isolation of a nuclear waste repository. The analytical methodology used to determine potential environmental effects required definition of a hypothetical environmental setting and repository. Potentially applicable regulatory requirements were identified and were used as guidelines to evaluate permitting feasibility. The environmental effects of repository development were analyzed for the two major time periods of concern: short term (the period of construction, operation, and decommissioning) and long term (the isolation period after decommissioning). As a result of this analysis, major environmental uncertainties and issues were identified. 11 references, 5 figures

Low level waste repositories

International Nuclear Information System (INIS)

Hill, P.R.H.; Wilson, M.A.

1983-11-01

Factors in selecting a site for low-level radioactive waste disposal are discussed. South Australia has used a former tailings dam in a remote, arid location as a llw repository. There are also low-level waste disposal procedures at the Olympic Dam copper/uranium project

Repository site characterization

International Nuclear Information System (INIS)

Voss, J.W.; Pentz, D.L.

1987-01-01

The characterization of candidate repository sites has a number of programmatic objectives. Principal among these is the acquisition of data: a) to determine the suitability of a site relative to the DOE repository siting guidelines, b) to support model development and calculations to determine the suitability of a site relative to the post closure criteria of the NRC and EPA, c) to support the design of a disposal system, including the waste package and the engineered barrier system, as well as the shafts and underground openings of the repository. In meeting the gaols of site characterization, the authors have an obligation to conduct their investigations within an appropriate budget and schedule. This mandates that a well-constructed and systematic plan for field investigations be developed. Such a plan must fully account for the mechanisms which will control the radiologic performance in the repository. The plan must also flexibly and dynamically respond to the results of each step of field investigation, responding to the spatial variability of earth as well as to enhanced understandings of the performance of the disposal system. Such a plan must ensure that sufficient data are available to support the necessary probabilistic calculations of performance. This paper explores the planning for field data acquisition with specific reference to requirements for demonstrations of the acceptable performance for disposal systems

Probabilistic calculations and sensitivity analysis of parameters for a reference biosphere model assessing the potential exposure of a population to radionuclides from a deep geological repository

Energy Technology Data Exchange (ETDEWEB)

Staudt, Christian; Kaiser, Jan Christian [Helmholtz Zentrum Muenchen, Institute of Radiation Protection, Munich (Germany); Proehl, Gerhard [International Atomic Energy Agency, Division of Radiation, Transport and Waste Safety, Wagramerstrasse 5, 1400 Vienna (Austria)

2014-07-01

Radioecological models are used to assess the exposure of hypothetical populations to radionuclides. Potential radionuclide sources are deep geological repositories for high level radioactive waste. Assessment time frames are long since releases from those repositories are only expected in the far future, and radionuclide migration to the geosphere biosphere interface will take additional time. Due to the long time frames, climate conditions at the repository site will change, leading to changing exposure pathways and model parameters. To identify climate dependent changes in exposure in the far field of a deep geological repository a range of reference biosphere models representing climate analogues for potential future climate states at a German site were developed. In this approach, model scenarios are developed for different contemporary climate states. It is assumed that the exposure pathways and parameters of the contemporary biosphere in the far field of the repository will change to be similar to those at the analogue sites. Since current climate models cannot predict climate developments over the assessment time frame of 1 million years, analogues for a range of realistically possible future climate conditions were selected. These climate states range from steppe to permafrost climate. As model endpoint Biosphere Dose conversion factors (BDCF) are calculated. The radionuclide specific BDCF describe the exposure of a population to radionuclides entering the biosphere in near surface ground water. The BDCF are subject to uncertainties in the exposure pathways and model parameters. In the presented work, probabilistic and sensitivity analysis was used to assess the influence of model parameter uncertainties on the BDCF and the relevance of individual parameters for the model result. This was done for the long half-live radionuclides Cs-135, I-129 and U-238. In addition to this, BDCF distributions for nine climate reference regions and several scenarios were

Biosphere modelling for the assessment of radioactive waste repositories; the development of a common basis by the BIOMOVS II reference biospheres working group

International Nuclear Information System (INIS)

Dorp, F. van; Egan, M.; Kessler, J.H.; Nilsson, S.; Pinedo, P.; Smith, G.; Torres, C.

1998-01-01

Performance criteria for radioactive waste repositories are often expressed in terms of dose or risk. The characteristics of biosphere modelling for performance assessment are that: (a) potential release occurs in the distant future, (b) reliable predictions of human behaviour at the time of release are impracticable, and (c) the biosphere is not considered to be a barrier as the geosphere and the engineered barriers. For these and other reasons, differences have arisen in the approaches to biosphere modelling for repository dose and risk assessment. The BIOMOVS II Reference Biospheres Working Group has developed (a) a recommended methodology for biosphere model development, (b) a structured list of features, events and processes (FEPs) which the model should describe, and (c) an illustrative example of the recommended methodology. The Working Group has successfully tested the Interaction Matrix (or Rock Engineering Systems, RES) approach for developing conceptual models. The BIOMOVS II Working Groups on Reference Biospheres and Complementary Studies have laid the basis for considerable harmonisation in approaches to biosphere modelling of long term radionuclide releases. (Copyright (c) 1998 Elsevier Science B.V., Amsterdam. All rights reserved.)

Effects of repository conditions on environmental impact reduction by recycling

International Nuclear Information System (INIS)

Ahn, Joonhong

2010-01-01

The environmental impacts (EI) of high-level wastes (HLW) disposed of in a water-saturated repository (WSR) and in the Yucca Mountain Repository (YMR) for various fuel cycle cases have been evaluated and compared to observe the difference in the recycling effects for differing repository conditions. With the impacts of direct spent fuel disposal in each repository as the reference level, separation of actinides by Urex+ and borosilicate vitrification clearly reduces the environmental impacts of YMR, while separation by Purex and borosilicate vitrification would not necessarily reduce the environmental impact of WSR. (authors)

Radioactive waste isolation in salt: peer review of Westinghouse Electric Corporation's report on reference conceptual designs for a repository waste package

Energy Technology Data Exchange (ETDEWEB)

Rote, D.M.; Hull, A.B.; Was, G.S.; Macdonald, D.D.; Wilde, B.E.; Russell, J.E.; Kruger, J.; Harrison, W.; Hambley, D.F.

1985-10-01

This report documents the findings of the peer panel constituted by Argonne National Laboratory to review Region A of Westinghouse Electric Corporation's report entitled Waste Package Reference Conceptual Designs for a Repository in Salt. The panel determined that the reviewed report does not provide reasonable assurance that US Nuclear Regulatory Commission (NRC) requirements for waste packages will be met by the proposed design. It also found that it is premature to call the design a ''reference design,'' or even a ''reference conceptual design.'' This review report provides guidance for the preparation of a more acceptable design document.

Preliminary concepts: materials management in an internationally safeguarded nuclear-waste geologic repository

International Nuclear Information System (INIS)

Ostenak, C.A.; Whitty, W.J.; Dietz, R.J.

1979-11-01

Preliminary concepts of materials accountability are presented for an internationally safeguarded nuclear-waste geologic repository. A hypothetical reference repository that receives nuclear waste for emplacement in a geologic medium serves to illustrate specific safeguards concepts. Nuclear wastes received at the reference repository derive from prior fuel-cycle operations. Alternative safeguards techniques ranging from item accounting to nondestructive assay and waste characteristics that affect the necessary level of safeguards are examined. Downgrading of safeguards prior to shipment to the repository is recommended whenever possible. The point in the waste cycle where international safeguards may be terminate depends on the fissile content, feasibility of separation, and practicable recoverability of the waste: termination may not be possible if spent fuels are declared as waste

An analysis of repository waste-handling operations

International Nuclear Information System (INIS)

Dennis, A.W.

1990-09-01

This report has been prepared to document the operational analysis of waste-handling facilities at a geologic repository for high-level nuclear waste. The site currently under investigation for the geologic repository is located at Yucca Mountain, Nye County, Nevada. The repository waste-handling operations have been identified and analyzed for the year 2011, a steady-state year during which the repository receives spent nuclear fuel containing the equivalent of 3000 metric tons of uranium (MTU) and defense high-level waste containing the equivalent of 400 MTU. As a result of this analysis, it has been determined that the waste-handling facilities are adequate to receive, prepare, store, and emplace the projected quantity of waste on an annual basis. In addition, several areas have been identified where additional work is required. The recommendations for future work have been divided into three categories: items that affect the total waste management system, operations within the repository boundary, and the methodology used to perform operational analyses for repository designs. 7 refs., 48 figs., 11 tabs

Kriging analysis for a candidate nuclear waste repository

International Nuclear Information System (INIS)

Devary, J.L.

1983-08-01

An important aspect of ensuring the safety of a geologic nuclear waste repository involves the study of ground-water flow at the proposed site. Geohydrologic site characterization involves the evaluation of potentiometric (head) data from confined aquifers. Geostatistical techniques (kriging) are applied to head measurements from the Permian System, a geologic formation being considered by the Department of Energy for nuclear waste disposal. The kriging analysis investigates the adequacy of the data base, provides methods for data screening, and determines optimal locations for additional data collection. This presentation illustrates the development of a generalized covariance and the production of potentiometric contour maps and error maps. The advantages of kriging over traditional least squares regression analysis are also discussed. 17 references

Permian Basin location recommendation report

International Nuclear Information System (INIS)

1983-09-01

Candidate study areas are screened from the Palo Duro and Dalhart Basin areas using data obtained from studies to date and criteria and specifications that consider: rock geometry; rock characteristics; human intrusion potential; surface characteristics; and environmental and socioeconomic conditions. Two preferred locations are recommended from among these areas for additional characterization to identify potential National Waste Terminal Storage (NWTS) salt repository sites. One location, in northeastern Deaf Smith County and southeastern Oldham County, is underlain by two salt units that meet the adopted screening specifications. The other location, in northcentral Swisher County, is underlain by one salt unit that meets the adopted screening specifications. Both locations have several favorable features, relative to surrounding areas, and no obviously undesirable characteristics. Both lie wholly on the Southern High Plains surface, are in relatively sparsely populated areas, contain no unique land use conflicts, and comprise large enough geographic areas to provide flexibility in site selection. Data gathered to date indicate that these locations contain salt units sufficient in thickness and in depth for the safe construction and operation of the underground facilities under consideration. 93 references, 34 figures, 6 tables

The Ec prototype repository project: implications of assessments for refining repository design

International Nuclear Information System (INIS)

Svemar, C.

2004-01-01

The most important issue in the evaluation of the repository performance is the long term safety of the repository. Analyses for this issue focuses on the 'steady state' conditions which start at the time when the repository has been saturated and the groundwater table returned to its normal level. The bentonite buffer around the canisters is saturated and homogeneous, and the canister is located exactly in the centre of the buffer. The backfill in the tunnel has been saturated as well and fills the earlier open spaces in the tunnel completely. The task of the activities taking places prior to the start of the 'steady state' conditions, like excavation, deposition, backfilling and sealing, with due consideration to the processes a consequences they may cause in the long run, is to provide for these 'ideal' conditions, as close as possible. While studying these activities in detail it has become obvious that development of methods and techniques needs to be carefully addressed before the decision is made on how to apply them in the repository. One general finding is that the situation in engineering of details is not that much different from the situation in geological characterisation of a site in detail; one more detail of engineering and the consequences it brings often complicates the situation rather than supports the solution prioritized so far. Many of the practical issues have been studied in the Prototype Repository project in the AEspoe Hard Rock Laboratory (Pusch et al., 2000). The Prototype Repository consists of two sections with four respectively two deposition holes with bentonite buffer and canister, the latter holding electrical heaters. The sections are separated by a concrete plug, and the whole test is to be separated from the rest of the laboratory by an outer plug. The project has two objectives: 1. To demonstrate the integrated function of tile deep repository components under realistic conditions and to compare results with models and

Salt repository design approach

International Nuclear Information System (INIS)

Matthews, S.C.

1983-01-01

This paper presents a summary discussion of the approaches that have been and will be taken in design of repository facilities for use with disposal of radioactive wastes in salt formations. Since specific sites have yet to be identified, the discussion is at a general level, supplemented with illustrative examples where appropriate. 5 references, 1 figure

Environmental assessment: Reference repository location, Hanford Site, Washington (US)

Energy Technology Data Exchange (ETDEWEB)

none,

1986-05-01

This appendix responds to the issues raised by Federal, State, and local governments, affected Indian Tribes, private citizens, and other organizations on the draft environmental assessment (EA) that was prepared pursuant to Section 112 of the Nuclear Waste Policy Act of 1982. In addition to presenting the issues raised in the comments and the responses, it describes where changes were made in the final EA. 535 refs., 13 figs., 16 tabs.

Evaluation of geochemical properties used in area-to-location screening for a nuclear waste repository at the Nevada Test Site

International Nuclear Information System (INIS)

Purson, J.D.

1983-03-01

The area-to-location screening of a potential site for a nuclear waste repository is dependent on geologic compatibility. Specifically, the geochemical properties of candidate locations are significant in the overall site evaluation. This report describes three geochemical factors or attributes and their application to an area-to-location screening of the southwestern quadrant of the Nevada Test Site and contiguous areas. These are only 3 of 31 attributes examined in the screening process. Geochemical and rock media considerations relevant to site screening include: (1) retardation by hydraulics - a study of ground-water movement through fractures vs a permeable matrix; (2) thermal stability of minerals - a measurement of undesirable mineral assemblages in the rock; and (3) retardation by sorption - an evaluation of the total sorptive capacity at a location, based on stratigraphy and lithology. Twelve potential host rocks situated in 20 locations are examined; 2 of these have consistently fewer favorable characteristics, and 6 others have generally fewer favorable characteristics than the 4 remaining rock units. The four units that appear most favorable by geochemical measures are the tuffaceous beds of Calico Hills, granite intrusives, the densely welded Topopah Spring tuff, and the Crater Flat Tuff at Yucca Mountain

16 CFR Figure 3 to Part 1203 - Location of Reference Plane

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Location of Reference Plane 3 Figure 3 to Part 1203 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION CONSUMER PRODUCT SAFETY ACT... Plane ER10MR98.003 ...

Project JADE. Long-term function and safety. Comparison of repository systems

International Nuclear Information System (INIS)

Birgersson, Lars; Pers, K.; Wiborgh, M.

2001-12-01

A comparison of the KBS-3 V(ertical deposition), KBS-3 H(orizontal deposition) and MLH repository systems with regard to the long-term repository performance and the radionuclide migration is presented in the report. Several differences between the repository systems have been identified. The differences are mainly related to the: distance between canister and backfilled tunnels, excavated rock volumes, deposition hole direction. The overall conclusion is that the differences are in general quite small with regard to the repository function and safety. None of the differences are of such importance for the long-term repository performance and radionuclide migration that they discriminate any of the repository systems. The differences between the two KBS-3 systems are small. Based on this study, there is no reason to change from the reference system KBS-3 V to KBS-3 H. MLH has the potential to be a very robust system, especially in a long-term perspective. However, the MLH system will require extensive research, development, and analysis before it will be as confident as the reference repository system, KBS-3 V. Although the MLH and KBS-3 H systems are in some ways favourable compared to the reference system KBS-3 V, the overall conclusion is that the KBS-3 V system is still a very attractive system. A major advantage with KBS-3 V is that it is by far the most investigated and developed system. The JADE-project was initiated in 1996, and the main part of the study was carried out during 1997 and 1998. The JADE study is consequently based on presumptions that were valid a few years ago. Some of these presumptions have been modified since then. The new presumptions are however not judged to change the overall conclusions

Natural Elemental Concentrations and Fluxes: Their Use as Indicators of Repository Safety

International Nuclear Information System (INIS)

Miller, Bill; Lind, Andy; Savage, Dave; Maul, Philip; Robinson, Peter

2002-03-01

individual processes, such as groundwater discharge, river flow and erosion at specific locations. The approach can also be of value at the generic level of repository development, before site characterisation programmes have been undertaken. They could be used, for example, as a component in comparative evaluations of alternative generic disposal concepts. The objective at the generic level would be to define typical or average natural elemental concentrations and fluxes in geological systems representative of the environments which might host a repository, and to compare these with the outputs from the associated generic PAs. To facilitate the use of the natural safety indicators methodology at the generic level, this study has undertaken to bring together and to compile much of the required information. This information has been used to quantify average elemental mass fluxes at the global scale for a range of processes, including groundwater discharge, erosion and sediment transport. The point of these calculations is that they provide a baseline against which site or geological environment specific natural fluxes, from anywhere in the world, can be compared on an equal basis to evaluate if they are higher or lower than the global average and, thus, are useful for providing a broad natural context for predicted repository releases. In separate calculations, elemental mass fluxes were quantified for a number of reference environments which are chosen to be representative of the types of sites and geological systems which may host a deep repository. The reference environments were an inland pluton, basement under sedimentary cover and a sedimentary basin. The fluxes for these environments were calculated for systems with spatial scales of a few hundred square kilometres and, as such, approximate closely to the repository systems modelled in PAs because a reference environment represents the same system, with the same rock, groundwater and surface conditions as those

Uncertainties in sealing a nuclear waste repository in partially saturated tuff

International Nuclear Information System (INIS)

Tillerson, J.R.; Fernandez, J.A.; Hinkebein, T.E.

1989-01-01

Sealing a nuclear waste repository in partially saturated tuff presents unique challenges to assuring performance of sealing components. Design and performance of components for sealing shafts, ramps, drifts, and exploratory boreholes depend on specific features of both the repository design and the site; of particular importance is the hydrologic environment in the unsaturated zone, including the role of fracture flow. Repository design features important to sealing of a repository include the size and location of shaft and ramp accesses, excavation methods, and the underground layout features such as grade (drainage direction) and location relative to geologic structure. Uncertainties about seal components relate to the postclosure environment for the seals, the emplacement methods, the material properties, and the potential performance of the components. An approach has been developed to reduce uncertainties and to increase confidence in seal performance; it includes gathering extensive site characterization data, establishing conservative design requirements, testing seal components in laboratory and field environments, and refining designs of both the seals and the repository before seals are installed. 9 refs., 5 figs., 2 tabs

Memorandum concerning further information on the constructional feasibility of proposed locations for stage 2 of the deep geological repositories project; Nachforderung zum Indikator „Tiefenlage im Hinblick auf bautechnische Machbarkeit“ in Etappe 2 SGT

Energy Technology Data Exchange (ETDEWEB)

NONE

2015-11-15

This memorandum published by the Swiss Federal Nuclear Safety Inspectorate ENSI examines proposals made by the Swiss National Cooperative for the disposal of Radioactive Waste (NAGRA). Further information concerning the technical feasibility of deep repositories for nuclear wastes and their maximum depth is requested. ENSI requests from NAGRA that the minimum geotechnical requirements on the repositories and an assessment on their maximum depth be stated. Five main areas where more information is required are listed. Provisional assessment results on maximum repository depth are quoted and the associated requirements on supplementary data required are listed. Data on basic rock mechanics are requested and requirements on the evaluation of maximum repository depth are discussed. The document is completed with a comprehensive list of relevant references.

Release consequence analysis for a hypothetical geologic radioactive waste repository in hard rock

International Nuclear Information System (INIS)

1979-12-01

This report makes an evaluation of the long-term behaviour of the wastes placed in a hard rock repository. Impacts were analyzed for the seven reference fuel cycles of WG 7. The reference repository for this study is for granitic rock or gneiss as the host rock. The descriptions of waste packages and repository facilities used in this study represent only one of many possible designs based on the multiple barriers concept. The repository's size is based on a nuclear economy producing 100 gigawatts of electricity per year for 1 year. The objective of the modeling efforts presented in this study is to predict the rate of transport of radioactive contaminants from the repository through the geosphere to the biosphere and thus determine an estimate of the potential dose to humans so that the release consequence impacts of the various fuel cycles can be compared. Currently available hydrologic, leach, transport, and dose models were used in this study

Schematic designs for penetration seals for a repository in the Paradox Basin

International Nuclear Information System (INIS)

Kelsall, P.C.; Meyer, D.; Case, J.B.; Coons, W.E.

1985-12-01

The isolation of radioactive wastes in geologic repositories requires that human-made penetrations such as shafts, tunnels, or boreholes are adequately sealed. This report describes schematic seal designs for a repository in bedded salt referenced to the stratigraphy of the Paradox Basin. The designs are presented for extensive peer review and will be updated as conceptual designs if the Paraodx Basin is selected as a candidate repository site. The principal components used in the shaft seal system are concrete bulkheads interspersed with highly compacted bentonite-rich earth fill. In the repository-level tunnels and rooms, the principal material used in the seal system is crushed salt obtained from excavating the repository. It is anticipated that crushed salt will consolidate in response to closure of the repository rooms, to the degree that mechanical and hydrologic properties will eventually match those of undisturbed, intact salt. For Paradox Basin Cycle 6 salt, analyses indictate that this process will require approximately 300 years for a seal located at the base of one of the repository shafts (where there is little increase in temperature due to waste emplacement) and approximately 140 years for a seal located in a main passageway within the repository. These analyses are based on uncertain laboratory data regarding intact salt creep rates and crushed salt consolidation characteristics, and must be regarded as preliminary

Repository thermal response: A preliminary evaluation of the effects of modeled waste stream resolution

International Nuclear Information System (INIS)

Ryder, E.E.; Dunn, E.

1995-09-01

One of the primary factors that influences our predictions of host-rock thermal response within a high level waste repository is how the waste stream's represented in the models. In the context of thermal modeling, waste stream refers to an itemized listing of the type (pressurized-water or boiling-water reactor), age, burnup, and enrichment of the spent nuclear fuel assemblies entering the repository over the 25-year emplacement phase. The effect of package-by-package variations in spent fuel characteristics on predicted repository thermal response is the focus of this report. A three-year portion of the emplacement period was modeled using three approaches to waste stream resolution. The first assumes that each package type emplaced in a given year is adequately represented by average characteristics. For comparison, two models that explicitly account for each waste package's individual characteristics were run; the first assuming a random selection of packages and the second an ordered approach aimed at locating the higher power output packages toward the center of the emplacement area. Results indicate that the explicit representation of packages results in hot and cold spots that could have performance assessment and design implications. Furthermore, questions are raised regarding the representativeness of average characteristics with respect to integrated energy output and the possible implications of a mass-based repository loading approach

Classifying decommissioning wastes for allocation to appropriate final repositories

International Nuclear Information System (INIS)

Alder, J.C.; Tunaboylu, K.

1982-01-01

For the safe disposal of radioactive wastes in different repositories, it is of advantage to classify them in well-defined conditioned categories, appropriate for final disposal. These categories, the so-called waste sorts are characterized by similar radionuclide distribution, similar nuclide-specific activity concentrations and similar waste matrix. A methodology is presented for classifying decommissioning wastes and is applied to the decommissioning wastes arising from a Swiss program of 6 GWe. The amounts and nuclide-specific activity inventories of the decommissioning waste sorts have been estimated. A first allocation into two different repository types has been performed. Such a classification enables one to define the source parameters for repository safety analysis and allows one to allocate the different waste categories into appropriate final repositories. This work presents a first iteration to determine which waste sorts belong to which repository type. The characteristics of waste sorts have to be better defined and the protective strength of the repository barriers has to be optimized. 7 references, 2 figures, 4 tables

Generic Argillite/Shale Disposal Reference Case

Energy Technology Data Exchange (ETDEWEB)

Zheng, Liange; Colon, Carlos Jové; Bianchi, Marco; Birkholzer, Jens

2014-08-08

properties (parameters) used in these models are different, which not only make inter-model comparisons difficult, but also compromise the applicability of the lessons learned from one model to another model. The establishment of a reference case would therefore be helpful to set up a baseline for model development. A generic salt repository reference case was developed in Freeze et al. (2013) and the generic argillite repository reference case is presented in this report. The definition of a reference case requires the characterization of the waste inventory, waste form, waste package, repository layout, EBS backfill, host rock, and biosphere. This report mainly documents the processes in EBS bentonite and host rock that are potentially important for performance assessment and properties that are needed to describe these processes, with brief description other components such as waste inventory, waste form, waste package, repository layout, aquifer, and biosphere. A thorough description of the generic argillite repository reference case will be given in Jové Colon et al. (2014).

Data Stewardship: Environmental Data Curation and a Web-of-Repositories

Directory of Open Access Journals (Sweden)

Karen S. Baker

2009-10-01

Full Text Available Scientific researchers today frequently package measurements and associated metadata as digital datasets in anticipation of storage in data repositories. Through the lens of environmental data stewardship, we consider the data repository as an organizational element central to data curation. One aspect of non-commercial repositories, their distance-from-origin of the data, is explored in terms of near and remote categories. Three idealized repository types are distinguished – local, center, and archive - paralleling research, resource, and reference collection categories respectively. Repository type characteristics such as scope, structure, and goals are discussed. Repository similarities in terms of roles, activities and responsibilities are also examined. Data stewardship is related to care of research data and responsible scientific communication supported by an infrastructure that coordinates curation activities; data curation is defined as a set of repeated and repeatable activities focusing on tending data and creating data products within a particular arena. The concept of “sphere-of-context” is introduced as an aid to distinguishing repository types. Conceptualizing a “web-of-repositories” accommodates a variety of repository types and represents an ecologically inclusive approach to data curation.

Nuclide release from the near-field of a L/ILW repository

International Nuclear Information System (INIS)

Karlsson, L.G.; Hoeglund, L.O.; Pers, K.

1986-12-01

For Project Gewaehr 1985, the release of nuclides from a repository for low- and intermediate-level radioactive waste is calculated. The calculations are made for a reference design repository located in the marl host rock at the Oberbauen Stock reference site. The results are limited to the release of the nuclides from the waste through the engineered barriers into the surrounding host rock and will, therefore, constitute a source term for the far-field and biosphere calculations. The most probable nuclide transport mechanism is diffusion and releases are thus influenced by the nuclide diffusivities in the barriers, nuclide sorption and nuclide solubility limits. Degradation of the engineered concrete barriers is taken into account. The effects of convective flow through the barriers are described elsewhere. A near-field release model is presented. It consists of a set of computer programs suited to handel different repository designs, solubility limitations and the different waste categories. The release calculations were made for a base case in which best estimates of the parameters were used. Sensitivity to the choice of the most important parameters was tested by parameter variations. The numerical models used were checked by comparative calculations with different codes and similar data. The results of the base calculations show that near-field barriers will cause both a delay of the release to the far-field and a reduced rate of release. The sorbed nuclides, comprising the actinides and some activation and fission products, will be delayed by 10'000 years and have a maximum release rate of less than 10 -3 Ci/a each. The non-sorbed nuclides are delayed by only about 100 years and the maximum release rate is less than 10 -2 Ci per year and nuclide. The parameter variations and the design model tests gave only limited deviations from the base case results. (author)

Review. Deep repository for spent nuclear fuel SR 97 - Post-closure safety

Energy Technology Data Exchange (ETDEWEB)

Stephansson, Ove [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Civil and Environmental Engineering

2000-12-01

mechanical development of the respective areas and their place in space and time during the geological evolution of the Baltic Shield. This makes it difficult to rank the suggested sites based on their past, present and future geological evolution. The problem of large discrepancies in data needs to be resolved before stress measurements are performed at future sites. For stress measurements in general and the demand of good quality data at the future sites, there is a need for integrated stress analysis where data from different stress measurements methods (overcoring, hydrofracturing, hydraulic testing of pre-existing fractures and focal mechanism studies) are combined in an integrated stress analysis. Results from orientation of horizontal components from the stress measurements at the three sites clearly demonstrate the relatively large variation in orientation both at each site and between different sites. The relationship between the state of stress and the location and orientation of the major fracture zones is of outmost importance in a future location of a final repository. Preliminary repository layout was constructed by SKB for each selected repository site to accommodate approximately 4,000 canisters. From rock stability point of view the deposition tunnels should be oriented parallel with the orientation of the maximum horizontal principal stress. This is one of the fundamental principles in rock engineering. However, SKB prefer to orient the tunnel axes perpendicular to the maximum stress because the fracture zones and their respect distance, the orientation of water-bearing fracture zones and the area for repository location does not allow a proper tunnel orientation with respect to the orientation of the horizontal rock stresses. The orientation of the tunnels as suggested might lead to spalling or other types of failure of the tunnels and deposition hole. There has been a number of international studies about this problem and SKB has to give this problem

Nuclear waste repository in basalt: preconceptual design guidelines

International Nuclear Information System (INIS)

1979-06-01

The development of the basalt waste isolation program parallels the growing need for permanent, environmentally safe, and secure means to store nuclear wastes. The repository will be located within the Columbia Plateau basalt formations where these ends can be met and radiological waste can be stored. These wastes will be stored such that the wastes may be retrieved from storage for a period after placement. After the retrieval period, the storage locations will be prepared for terminal storage. The terminal storage requirements will include decommissioning provisions. The facility boundaries will encompass no more than several square miles of land which will be above a subsurface area where the geologic makeup is primarily deep basaltic rock. The repository will receive, from an encapsulation site(s), nuclear waste in the form of canisters (not more than 18.5 feet x 16 inches in diameter) and containers (55-gallon drums). Canisters will contain spent fuel (after an interim 5-year storage period), solidified high-level wastes (HLW), or intermediate-level wastes (ILW). The containers (drums) will package the low-level transuranic wastes (LL-TRU). The storage capacity of the repository will be expanded in a time-phased program which will require that subsurface development (repository expansion) be conducted concurrently with waste storage operations. The repository will be designed to store the nuclear waste generated within the predictable future and to allow for reasonable expansion. The development and assurance of safe waste isolation is of paramount importance. All activities will be dedicated to the protection of public health and the environment. The repository will be licensed by the US Nuclear Regulatory Commission (NRC). Extensive efforts will be made to assure selection of a suitable site which will provide adequate isolation

Nuclear waste repository in basalt: preconceptual design guidelines

Energy Technology Data Exchange (ETDEWEB)

1979-06-01

The development of the basalt waste isolation program parallels the growing need for permanent, environmentally safe, and secure means to store nuclear wastes. The repository will be located within the Columbia Plateau basalt formations where these ends can be met and radiological waste can be stored. These wastes will be stored such that the wastes may be retrieved from storage for a period after placement. After the retrieval period, the storage locations will be prepared for terminal storage. The terminal storage requirements will include decommissioning provisions. The facility boundaries will encompass no more than several square miles of land which will be above a subsurface area where the geologic makeup is primarily deep basaltic rock. The repository will receive, from an encapsulation site(s), nuclear waste in the form of canisters (not more than 18.5 feet x 16 inches in diameter) and containers (55-gallon drums). Canisters will contain spent fuel (after an interim 5-year storage period), solidified high-level wastes (HLW), or intermediate-level wastes (ILW). The containers (drums) will package the low-level transuranic wastes (LL-TRU). The storage capacity of the repository will be expanded in a time-phased program which will require that subsurface development (repository expansion) be conducted concurrently with waste storage operations. The repository will be designed to store the nuclear waste generated within the predictable future and to allow for reasonable expansion. The development and assurance of safe waste isolation is of paramount importance. All activities will be dedicated to the protection of public health and the environment. The repository will be licensed by the US Nuclear Regulatory Commission (NRC). Extensive efforts will be made to assure selection of a suitable site which will provide adequate isolation.

Implementation of the Brazilian national repository

International Nuclear Information System (INIS)

Tello, Cledola Cassia Oliveira de

2013-01-01

Ionizing radiation in Brazil is used in electricity generation, medicine, industry, agriculture and for research and development purposes. All these activities can generate radioactive waste. At this point, in Brazil, the use of nuclear energy and radioisotopes justifies the construction of a national repository for radioactive wastes of low and intermediate-level. According to Federal Law No. 10308, Brazilian National Commission for Nuclear Energy (CNEN) is responsible for designing and constructing the intermediate and final storages for radioactive wastes. Additionally, a restriction on the construction of Angra 3 is that the repository is under construction until its operation start, attaining some requirements of the Brazilian Environmental Regulator (IBAMA). The RBMN Project (Repository for Low and Intermediate-Level Radioactive Wastes) aims at the implantation of a National Repository for disposal of low and intermediate-level of radiation wastes. This Project has some aspects that are unique in the Brazilian context, especially referring to the time between its construction and the end of its institutional period. This time is about 360 years, when the area will be released for unrestricted uses. It means that the Repository must be safe and secure for more than three hundred years, which is longer than half of the whole of Brazilian history. This aspect is very new for the Brazilian people, bringing a new dimension to public acceptance. Another point is this will be the first repository in South America, bringing a real challenge for the continent. The current status of the Project is summarized. (author)

An evaluation of repository-induced disturbances for a KBS-3 type repository

Energy Technology Data Exchange (ETDEWEB)

Savage, D.; McLeod, R.; McEwen, T. [QuantiSci, Melton Mowbray (United Kingdom)

1998-03-01

This report considers the potential physical and chemical perturbations caused by the excavation, operation and backfilling and sealing of a KBS-3 type repository for spent fuel in Sweden. Parts of the underground excavations are likely to remain open to the atmosphere for up to several decades. Time-dependent changes to the chemical environment and the properties of the geological formation will be occurring as well as the initial disturbance of construction and subsequent changes after backfilling. In addition, this report also discusses issues that arise from the co-disposal of spent fuel and intermediate level waste. The processes which are likely to act during each stage of a repository from construction through to backfilling and sealing have been reviewed and the degree to which these processes are understood and represented within the performance assessment is discussed. The areas of particular interest are: The coupling of thermal, hydrogeological and mechanical processes with particular reference to the development of the near-field; Understanding the transient process of re-saturation with particular reference to the buffer material surrounding the waste canisters, including chemical changes to the material; The impact of accidental events during the construction and operational phases of work and their possible consequence on the long term performance of the repository; Chemical issues relating to the co-disposal of spent fuel and intermediate level wastes within a single facility. When consideration of transient processes and coupling is discussed, it is apparent that numerical tools and a complete understanding to provide quantitative information is lacking. The importance of the engineered barrier system within the performance assessment for spent fuel disposal is recognised and the emphasis is placed on the understanding of the coupled processes in the evolution in the near-field of the geosphere 45 refs, 4 fig, 2 tabs

An evaluation of repository-induced disturbances for a KBS-3 type repository

International Nuclear Information System (INIS)

Savage, D.; McLeod, R.; McEwen, T.

1998-03-01

This report considers the potential physical and chemical perturbations caused by the excavation, operation and backfilling and sealing of a KBS-3 type repository for spent fuel in Sweden. Parts of the underground excavations are likely to remain open to the atmosphere for up to several decades. Time-dependent changes to the chemical environment and the properties of the geological formation will be occurring as well as the initial disturbance of construction and subsequent changes after backfilling. In addition, this report also discusses issues that arise from the co-disposal of spent fuel and intermediate level waste. The processes which are likely to act during each stage of a repository from construction through to backfilling and sealing have been reviewed and the degree to which these processes are understood and represented within the performance assessment is discussed. The areas of particular interest are: The coupling of thermal, hydrogeological and mechanical processes with particular reference to the development of the near-field; Understanding the transient process of re-saturation with particular reference to the buffer material surrounding the waste canisters, including chemical changes to the material; The impact of accidental events during the construction and operational phases of work and their possible consequence on the long term performance of the repository; Chemical issues relating to the co-disposal of spent fuel and intermediate level wastes within a single facility. When consideration of transient processes and coupling is discussed, it is apparent that numerical tools and a complete understanding to provide quantitative information is lacking. The importance of the engineered barrier system within the performance assessment for spent fuel disposal is recognised and the emphasis is placed on the understanding of the coupled processes in the evolution in the near-field of the geosphere

Design perspectives for the low and intermediate level radioactive waste repository in Korea

International Nuclear Information System (INIS)

Kim, Young Ki; Koh, Kwang Hoon; Lee, Sang Sun; Lee, Byung Sik; Choi, Gi Won

2007-01-01

The underground waste repository is located at Gyeongju and is designed for the disposal of all the Low- and Intermediate Level Radioactive Waste(LILW). It is scheduled to commence operations in the beginning of 2009. The repository, with a disposal capacity of 800,000 drums, will be constructed in granite rock near the seashore at the Gyeongju site. The repository will be designed to be constructed in phases to reach its final capacity 800,000 drums. In the first phase of construction, the repository will have a capacity to store 100,000 drums. The repository will house all LILW generated in the Republic of Korea. The first phase of the repository design consists of an assess shaft, a construction tunnel, an operating tunnel, an unloading tunnel, and six(6) silos. The silos are located at 80 to 130 meters below Mean Sea level (MSL), in bedrock. Each silo is 24.8m in diameter and 52.4m in height. The silo will be reinforced with concrete lining for rock supports which will also act aas an engineered barrier in limiting radioactive nuclide release aft closure. After serving its intended function the repository will be filled and sealed. The primary objective of filling and sealing is to prevent ground water flow into the silo through the tunnel system and to prevent inadvertent intrusion into the repository after closure

NPP Krsko: LILW Repository or Long Term Storage

International Nuclear Information System (INIS)

Lokner, V.; Subasic, D.; Levanat, I.

2008-01-01

Construction of the facilities for LILW and SF management, as planned in Decommissioning and LILW and SF management program for NPP Krsko, would be a rather expensive and challenging project for such a small nuclear program. In order to accommodate waste arising from a single nuclear power plant, one LILW repository should be constructed before the end of the NPP operation, then one SF dry storage, and finally one geological repository. This requires relatively urgent identification within Slovenian/Croatian territory of three locations that meet the criteria for establishment of such facilities and are acceptable to the local communities. There are very few such potential locations. The siting process for the first of the three facilities is well under way in Slovenia, because the country wants to have its LILW repository in operation by the year 2013. In order to facilitate public acceptance, Slovenian government has introduced financial incentives to local communities for the repository construction and operation. These 'compensations for limited land use' may significantly increase the overall costs of disposal if the repository is in operation for a long period. In the recent years, however, a possibility of long term storage (LTS) is gaining an increased attention in the waste management community, and has already been introduced e.g. in the Netherlands. It is a particularly viable option for limited waste quantities. Disposal remains the final solution, but present technologies have made possible a relatively inexpensive storage up to about hundred years, which can accommodate LILW, HLW and SF from nuclear programs as well as research reactor waste and NORM. Such storage would be a safe and simple temporary solution, encompassing all immediate and near future waste management needs. In addition, it would increase flexibility and reduce financing requirements for the final waste disposal: providing additional time for reduction of radiation emission and heat

Groundwater flow modelling of an abandoned partially open repository

Energy Technology Data Exchange (ETDEWEB)

Bockgaard, Niclas (Golder Associates AB (Sweden))

2010-12-15

As a part of the license application, according to the nuclear activities act, for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different hydraulic conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. The modelling study presented here serves as an input for analyses of so-called future human actions that may affect the repository. The objective of the work was to investigate the hydraulic influence of an abandoned partially open repository. The intention was to illustrate a pessimistic scenario of the effect of open tunnels in comparison to the reference closure of the repository. The effects of open tunnels were studied for two situations with different boundary conditions: A 'temperate' case with present-day boundary conditions and a generic future 'glacial' case with an ice sheet covering the repository. The results were summarized in the form of analyses of flow in and out from open tunnels, the effect on hydraulic head and flow in the surrounding rock volume, and transport performance measures of flow paths from the repository to surface

Groundwater flow modelling of an abandoned partially open repository

International Nuclear Information System (INIS)

Bockgaard, Niclas

2010-12-01

As a part of the license application, according to the nuclear activities act, for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different hydraulic conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. The modelling study presented here serves as an input for analyses of so-called future human actions that may affect the repository. The objective of the work was to investigate the hydraulic influence of an abandoned partially open repository. The intention was to illustrate a pessimistic scenario of the effect of open tunnels in comparison to the reference closure of the repository. The effects of open tunnels were studied for two situations with different boundary conditions: A 'temperate' case with present-day boundary conditions and a generic future 'glacial' case with an ice sheet covering the repository. The results were summarized in the form of analyses of flow in and out from open tunnels, the effect on hydraulic head and flow in the surrounding rock volume, and transport performance measures of flow paths from the repository to surface

Relationship of engineering geology to conceptual repository design in the Gibson Dome area, Utah

International Nuclear Information System (INIS)

Helgerson, R.; Henderson, N.

1984-01-01

The Paradox Basin in Southeastern Utah is being investigated as a potential site for development of a high-level nuclear waste repository. Geologic considerations are key areas of concern and influence repository design from a number of aspects: depth to the host rock, thickness of the host rock, and hydrologic conditions surrounding the proposed repository are of primary concern. Surface and subsurface investigations have provided data on these key geologic factors for input to the repository design. A repository design concept, based on the surface and subsurface geologic investigations conducted at Gibson Dome, was synthesized to provide needed information on technical feasibility and cost for repository siting decision purposes. Significant features of the surface and subsurface repository facilities are presented. 5 references, 4 figures

Aquatic ecosystem characterisation strategy at a repository site

Energy Technology Data Exchange (ETDEWEB)

Kangasniemi, Ville; Ikonen, Ari T.K. [Environmental Research and Assessment EnviroCase, Ltd., Hallituskatu 1 D 4, 28100 Pori (Finland); Lahdenperae, Anne-Maj [Saanio and Riekkola Oy, Laulukuja 4, 00420 Helsinki (Finland); Kirkkala, Teija [Pyhaejaervi Institute, Sepaentie 7, 27500 Kauttua (Finland); Koivunen, Sari [Water and Environment Research of South-West Finland, Telekatu 16, 20360 Turku (Finland)

2014-07-01

Olkiluoto Island on the western coast of Finland has been selected as a repository site for spent nuclear fuel disposal. According to regulatory requirements, the safety assessment for the repository should have an assessment timeframe of several millennia. Due to the post-glacial land uplift, the relatively shallow sea areas around Olkiluoto Island will change gradually to lakes, rivers and terrestrial areas. As there are no limnic systems at present Olkiluoto site, the reference area was delineated and reference lakes and rivers were selected as an analogue. For the modelling of the transport and accumulation of possible radionuclide releases in the surface environment, aquatic ecosystems were identified and divided into biotopes. Despite the number of available templates, the division of aquatic environment for the biosphere assessment of the Olkiluoto spent fuel repository was necessary to made separately. In this contribution, the processes behind the identification of aquatic ecosystems (e.g. legislation, physical and chemical properties) together with the biotope selection methodology (e.g. light and bottom conditions) and the challenges related to the amount of variable input parameters for each biotope in the modelling are presented. (authors)

Location memory biases reveal the challenges of coordinating visual and kinesthetic reference frames

Science.gov (United States)

Simmering, Vanessa R.; Peterson, Clayton; Darling, Warren; Spencer, John P.

2008-01-01

Five experiments explored the influence of visual and kinesthetic/proprioceptive reference frames on location memory. Experiments 1 and 2 compared visual and kinesthetic reference frames in a memory task using visually-specified locations and a visually-guided response. When the environment was visible, results replicated previous findings of biases away from the midline symmetry axis of the task space, with stability for targets aligned with this axis. When the environment was not visible, results showed some evidence of bias away from a kinesthetically-specified midline (trunk anterior–posterior [a–p] axis), but there was little evidence of stability when targets were aligned with body midline. This lack of stability may reflect the challenges of coordinating visual and kinesthetic information in the absence of an environmental reference frame. Thus, Experiments 3–5 examined kinesthetic guidance of hand movement to kinesthetically-defined targets. Performance in these experiments was generally accurate with no evidence of consistent biases away from the trunk a–p axis. We discuss these results in the context of the challenges of coordinating reference frames within versus between multiple sensori-motor systems. PMID:17703284

Natural Elemental Concentrations and Fluxes: Their Use as Indicators of Repository Safety

Energy Technology Data Exchange (ETDEWEB)

Miller, Bill; Lind, Andy; Savage, Dave; Maul, Philip; Robinson, Peter [EnvirosQuantisci, Melton Mowbray (United Kingdom)

2002-03-01

individual processes, such as groundwater discharge, river flow and erosion at specific locations. The approach can also be of value at the generic level of repository development, before site characterisation programmes have been undertaken. They could be used, for example, as a component in comparative evaluations of alternative generic disposal concepts. The objective at the generic level would be to define typical or average natural elemental concentrations and fluxes in geological systems representative of the environments which might host a repository, and to compare these with the outputs from the associated generic PAs. To facilitate the use of the natural safety indicators methodology at the generic level, this study has undertaken to bring together and to compile much of the required information. This information has been used to quantify average elemental mass fluxes at the global scale for a range of processes, including groundwater discharge, erosion and sediment transport. The point of these calculations is that they provide a baseline against which site or geological environment specific natural fluxes, from anywhere in the world, can be compared on an equal basis to evaluate if they are higher or lower than the global average and, thus, are useful for providing a broad natural context for predicted repository releases. In separate calculations, elemental mass fluxes were quantified for a number of reference environments which are chosen to be representative of the types of sites and geological systems which may host a deep repository. The reference environments were an inland pluton, basement under sedimentary cover and a sedimentary basin. The fluxes for these environments were calculated for systems with spatial scales of a few hundred square kilometres and, as such, approximate closely to the repository systems modelled in PAs because a reference environment represents the same system, with the same rock, groundwater and surface conditions as those

Studies on an advanced repository system with enhanced engineered barriers (a framework)

International Nuclear Information System (INIS)

Fujiwara, A.; Tashiro, S.; Ikari, S.; Suzuki, A.

1993-01-01

In order to propose advanced designs of repositories with enhanced engineered barriers of relatively high radioactive wastes such as burnable poisons, channel boxes, control rods and highly irradiated metals, studies started in 1987 and completed the first phase in 1992. This paper presents the framework and brief results of the first phase. The studies set preliminary design concepts of the repositories with various combinations with engineered barriers and natural barriers for different models and locations such as a silo type in shallow land or a tunnel type in intermediate depth. Through the designs, four component technics were picked up and studied for (1) construction of the components in repository; (2) performance evaluation to realize repository design; (3) improvement of circumstances inside or around repository; and (4) surveillance of repository performance to realize the repository designs. Finally, some repository systems were provided using obtained results, and then the applicability and the economy were evaluated. The studies will continue to the second phase focusing on the long-term performance of the repositories

Allocentrically implied target locations are updated in an eye-centred reference frame.

Science.gov (United States)

Thompson, Aidan A; Glover, Christopher V; Henriques, Denise Y P

2012-04-18

When reaching to remembered target locations following an intervening eye movement a systematic pattern of error is found indicating eye-centred updating of visuospatial memory. Here we investigated if implicit targets, defined only by allocentric visual cues, are also updated in an eye-centred reference frame as explicit targets are. Participants viewed vertical bars separated by varying distances, and horizontal lines of equivalently varying lengths, implying a "target" location at the midpoint of the stimulus. After determining the implied "target" location from only the allocentric stimuli provided, participants saccaded to an eccentric location, and reached to the remembered "target" location. Irrespective of the type of stimulus reaching errors to these implicit targets are gaze-dependent, and do not differ from those found when reaching to remembered explicit targets. Implicit target locations are coded and updated as a function of relative gaze direction with respect to those implied locations just as explicit targets are, even though no target is specifically represented. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Projected environmental impacts of radioactive material transportation to the first US repository site

International Nuclear Information System (INIS)

Neuhauser, K.S.; Cashwell, J.W.; Reardon, P.C.; Ostmeyer, R.M.; McNair, G.W.

1986-01-01

This paper discusses the relative national environmental impacts of transporting nuclear wastes to each of the nine candidate repository sites in the United States. Several of the potential sites are closely clustered and, for the purpose of distance and routing calculations, are treated as a single location. These are: Cypress Creek Dome and Richton Dome in Mississippi (Gulf Interior Region), Deaf Smith County and Swisher County sites in Texas (Permian Basin), and Davis Canyon and Lavender Canyon site in Utah (Paradox Basin). The remaining sites are: Vacherie Dome, Louisiana; Yucca Mountain, Nevada; and Hanford Reservation, Washington. For compatibility with both the repository system authorized by the NWPA and with the MRS option, two separate scenarios were analyzed. In belief, they are (1) shipment of spent fuel and high-level wastes (HLW) directly from waste generators to a repository (Reference Case) and (2) shipment of spent fuel to a Monitored Retrievable Storage (MRS) facility and then to a repository. Between 17 and 38 truck accident fatalities, between 1.4 and 7.7 rail accident fatalities, and between 0.22 and 12 radiological health effects can be expected to occur as a result of radioactive material transportation during the 26-year operating period of the first repository. During the same period in the United States, about 65,000 total deaths from truck accidents and about 32,000 total deaths from rail accidents would occur; also an estimated 58,300 cancer fatalities are predicted to occur in the United States during a 26-year period from exposure to background radiation alone (not including medical and other manmade sources). The risks reported here are upper limits and are small by comparison with the ''natural background'' of risks of the same type. 3 refs., 6 tabs

A compartment model for nuclide release calculation in the near-and far-field of a HLW repository

International Nuclear Information System (INIS)

Lee, Youn Myoung; Hwang, Yong Soo; Kang, Chul Hyung; Hahn, Pil Soo

2004-01-01

The HLW-relevant R and D program for disposal of high-level radioactive waste has been carried out at Korea Atomic Energy Research Institute (KAERI) since early 1997, from which a conceptual Korea Reference Repository System for direct disposal of nuclear spent fuel is to be introduced by the end of 2007. A preliminary reference geologic repository concept considering such established criteria and requirements as spent fuel and generic site characteristics in Korea was roughly envisaged in 2003. Not only to demonstrate how much a reference repository is safe in the generic point of view with several possible scenarios and cases associated with a preliminary repository concept by conducting calculations for nuclide release and transport in the near - and far - field components of the repository, even though sufficient information has not been available that much yet, but also to show a appropriate methodology by which both a generic and site - specific safety assessment could be performed for further in - depth development of Korea reference repository concept, nuclide release calculation study for various nuclide release cases is mandatory. To this end a similar study done and yet limited for the near - field release case has been extended to the case including far - field system by introducing some more geosphere compartments. Advective and longitudinal dispersive nuclide transports along the fracture with matrix diffusion as well as several retention mechanisms and nuclide ingrowth has been added

Repository-based software engineering program

Science.gov (United States)

Wilson, James

1992-01-01

The activities performed during September 1992 in support of Tasks 01 and 02 of the Repository-Based Software Engineering Program are outlined. The recommendations and implementation strategy defined at the September 9-10 meeting of the Reuse Acquisition Action Team (RAAT) are attached along with the viewgraphs and reference information presented at the Institute for Defense Analyses brief on legal and patent issues related to software reuse.

Is Croatia Going to Build a Radioactive Waste Repository?

International Nuclear Information System (INIS)

Knapp, Alemka; Levanat, Ivica; Saponja-Milutinovc, Diana

2014-01-01

Site selection process for low and intermediate level radioactive waste repository in Croatia was ended in 1999, nominating Trgovska gora as the potential macrolocation for the facility. Feasibility of the Trgovska gora disposal project was analyzed in a number of studies prepared by APO Ltd. from the mid-nineties up to 2003. An affirmative, though preliminary and largely generic safety assessment was completed. Specific microlocations were selected and analyzed based on literature data (garnished with low-resolution digital satellite pictures), and the best microlocation was tentatively narrowed down to Pavlovo brdo. After 2003, no further activities related to the repository project were undertaken for nearly ten years, until in its public procurement plan for 2013 the Croatian Fund for financing the NPP Krsko decommissioning and waste disposal dedicated over half a million euro to continuation of the project. In general, safe radioactive waste disposal pre-requires establishment of a complex national framework with appropriate functionality and competence; with such a framework established, decisive first steps towards building a repository are to identify potentially suitable locations and to ensure local community consent and cooperation. The rest should mainly be routine. But in Croatia, both lack of proper framework and the project history of indecisiveness may adversely affect further developments. Trgovska gora was designated as the potential location in the national land use plan only after three other potential locations had been dismissed by political decisions based on the largely assumed adverse attitudes of local communities. Repository project now appears to depend on cooperation of a single local community hosting the only potential site. The site has never been visited by any repository project participants, nor has the local community ever been officially contacted in an open and straightforward way, despite the 20-year old history of the project

A transport logistic and cost model for use in repository design specification

International Nuclear Information System (INIS)

Gray, L.S.; Manville, W.D.

1998-01-01

UK Nirex Ltd (Nirex) is responsible for developing a deep repository for the disposal of the United Kingdom's intermediate level waste and some low level waste. It also needs to be able to predict the total cost of the transport operations, and to compute the costs attributable to different combinations of sites and types of waste packages. This paper draws on work carried out as part of the assessment of Sellafield as a potential repository site, but will also show that many aspects of the transport system are independent of the actual repository location. To analyze the effects of all these possible scenarios and proposed operating practices on the costs and logistics of radioactive waste transport, Nirex commissioned the development of a flexible computer model from a software developer with the appropriate expertise. This paper describes how the LOGCOST model has been used to provide the information required for the repository design specification, and how it can readily be adapted to different potential repository locations and to changing requirements. In conclusion, it can be said that LOGCOST is a very effective transport and logistics model based on the Excel spread-sheet. The examples given have shown how LOGCOST can provide detailed predictions of radioactive waste transport costs, and how LOGCOST can be readily adapted to a new repository site or any other focal point for a transport network. (O.M.)

Radioactive waste repositories in hard rock aquifers--hydrodynamic aspects

International Nuclear Information System (INIS)

Thunvik, R.; Braester, C.

1984-01-01

A mathematical model for mass and heat flow and a computer program have been developed to demonstrate the effect of heat released from a hypothetical radioactive waste repository on the groundwater flow regime. The model, based on the continuum approach, conceptualizes the fracture pattern and the solid blocks as two overlapping continua and consists of a set of coupled nonlinear partial differential equations. The general form of the model is three-dimensional and can treat the fluid and rock either as two separate media with a quasi-steady exchange of heat between them or as a single equivalent medium with instantaneous thermal equilibrium. Numerical solutions have been obtained by the Galerkin finite element method. Examples have been presented for topographically different locations of the repository: below a horizontal ground surface, below a hill crest, below a hillside, and close to major fractures. The effects of constant permeability and porosity or downward decreasing with depth as well as the effect of anisotropic permeability have been investigated. Solutions include the velocity field, path lines, and traveling times of water particles passing the repository and the temperature distribution. The examples have been worked out for a two-dimensional flow domain, assuming that instantaneous thermal equilibrium takes place. This assumption was found to be justified by the relatively low flow velocities that occurred in the examples. Except for the location close to a major draining fracture, heat released from the radioactive waste repository may have a significant influence on the flow regime around the repository

Deep geological repository: Starting communication at potentially suitable sites

International Nuclear Information System (INIS)

Sumberova, Vera

2001-01-01

The siting of a deep geological repository in the Czech Republic is and will be a complicated process, since it is the first siting process of a nuclear facility designed from the start to be located at non-nuclear sites and to be organised under democratic conditions. This presentation describes the concept of radioactive waste and spent nuclear management in the Czech Republic, Communication activities of Radioactive Waste Repository Authority (RAWRA) with local representatives and lessons learned

Building Scientific Data's list of recommended data repositories

Science.gov (United States)

Hufton, A. L.; Khodiyar, V.; Hrynaszkiewicz, I.

2016-12-01

When Scientific Data launched in 2014 we provided our authors with a list of recommended data repositories to help them identify data hosting options that were likely to meet the journal's requirements. This list has grown in size and scope, and is now a central resource for authors across the Nature-titled journals. It has also been used in the development of data deposition policies and recommended repository lists across Springer Nature and at other publishers. Each new addition to the list is assessed according to a series of criteria that emphasize the stability of the resource, its commitment to principles of open science and its implementation of relevant community standards and reporting guidelines. A preference is expressed for repositories that issue digital object identifiers (DOIs) through the DataCite system and that share data under the Creative Commons CC0 waiver. Scientific Data currently lists fourteen repositories that focus on specific areas within the Earth and environmental sciences, as well as the broad scope repositories, Dryad and figshare. Readers can browse and filter datasets published at the journal by the host repository using ISA-explorer, a demo tool built by the ISA-tools team at Oxford University1. We believe that well-maintained lists like this one help publishers build a network of trust with community data repositories and provide an important complement to more comprehensive data repository indices and more formal certification efforts. In parallel, Scientific Data has also improved its policies to better support submissions from authors using institutional and project-specific repositories, without requiring each to apply for listing individually. Online resources Journal homepage: http://www.nature.com/scientificdata Data repository criteria: http://www.nature.com/sdata/policies/data-policies#repo-criteria Recommended data repositories: http://www.nature.com/sdata/policies/repositories Archived copies of the list: https

Nuclear waste repository in basalt: a design description

International Nuclear Information System (INIS)

Ritchie, J.S.; Schmidt, B.

1982-01-01

The conceptual design of a nuclear waste repository in basalt is described. Nuclear waste packages are placed in holes drilled into the floor of tunnels at a depth of 3700 ft. About 100 miles of tunnels are required to receive 35,000 packages. Five shafts bring waste packages, ventilation air, excavated rock, personnel, material, and services to and from the subsurface. The most important surface facility is the waste handling building, located over the waste handling shaft, where waste is received and packaged for storage. Two independent ventilation systems are provided to avoid potential contamination of spaces that do not contain nuclear waste. Because of the high temperatures at depth, an elaborate air chilling system is provided. Because the waste packages deliver a considerable amount of heat energy to the rock mass, particular attention is paid to heat transfer and thermal stress studies. 3 references, 31 figures, 3 tables

Thermo-mechanical analysis for multi-level HLW repository concept

International Nuclear Information System (INIS)

Kwon, Sang Ki; Choi, Jong Won

2004-01-01

This work aims to investigate the influence of design parameters for the underground high-level nuclear waste repository with multi-level concept. B. Necessity o In order to construct an HLW repository in deep underground, it is required to select a site, which is far from major discontinuities. To dispose the whole spent fuels generated from the Korean nuclear power plants in a repository, the underground area of about 4km 2 is required. This would be a constraints for selecting an adequate repository site. It is recommended to dispose the two different spent fuels, PWR and CANDU, in different areas at the operation efficiency point of view. It is necessary to investigate the influence of parameters, which can affect the stability of multi-level repository. It is also needed to consider the influence of heat generated from the HLW and the high in situ stress in deep location. Therefore, thermo-mechanical coupling analysis should be carried out and the results should be compared with the results from single-level repository concept. Three-dimensional analysis is required to model the disposal tunnel and deposition hole. It is recommended to use the Korean geological condition and actually measured rock properties in Korea in order to achieve reliable modeling results. A FISH routine developed for effective modeling of Thermal-Mechanical coupling was implemented in the modeling using FLAC3D, which is a commercial three-dimensional FDM code. The thermal and mechanical properties of rock and rock mass achieved from Yusung drilling site, were used for the computer modeling. Different parameters such as level distance, waste type disposed on different levels, and time interval between the operation on different levels, were considered in the three-dimensional analysis. From the analysis, it was possible to derive adequate multi-level repository concept. Results and recommendations for application From the thermal-mechanical analysis for the multi-level repository

Gabbro as a host rock for a nuclear waste repository

International Nuclear Information System (INIS)

Ahlbom, K.; Leijon, B.; Smellie, J.; Liedholm, M.

1992-09-01

As an alternative to granitic rocks, gabbro and other basic rock types have been investigated with respect to their suitability to host a nuclear waste repository. The present report summarizes and examines existing geoscientific knowledge of relevance in assessing the potential merits of gabbro as a repository host rock. Implications in terms of site selection, repository construction and post-closure repository performance are also discussed. The objective of the study is to provide a basis for decisions as regards future consideration of the gabbro alternative. It is found that there are rather few gabbro bodies in Sweden, that are potentially of sufficient size to host a repository. Thus, gabbro offers little latitude as regards site selection. In comparison to siting a repository in granitic rocks, this is a major disadvantage, and it may in fact remove gabbro from further consideration. The potential advantages of gabbro refer to repository performance, and include low hydraulic conductivity and a chemical environment promoting efficient radionuclide retardation. However, results from field investigations show that groundwater flow in gabbro bodies is largely controlled by intersecting heterogeneities, in particular granitic dykes, that are significantly more conductive to water than the gabbro. In the far-field scale significant to repository performance, this may reduce or eliminate the potential effects of favourable hydraulic and chemical characteristics of the gabbro itself. In conclusion, there are apparent difficulties associated with siting a repository in gabbro, due to lack of sufficiently large gabbro bodies. On the basis of the present state of knowledge, no decisive differences can be demonstrated when comparing gabbro with granitic rocks, neither with respects to repository construction, nor as regards repository performance. (au)

Radionuclide transport in the repository near-field and far-field

International Nuclear Information System (INIS)

Poteri, A.; Nordman, H.; Pulkkanen, V.-M.; Smith, P.

2014-01-01

This report is a background report of the TURVA-2012 safety case report 'Assessment of Radionuclide Release Scenarios for the Repository System'. This report gives a comprehensive account of the modelling of radionuclide release from a defective canister and the subsequent migration to the surface groundwater system. The focus of this report is in the radionuclide migration both in the repository near-field and in the repository far-field. Radionuclide releases from the canister and migration through the repository near-field and far-field have also been analysed in the probabilistic sensitivity analysis based on the Monte Carlo simulation method. Those simulations are discussed in a separate report by Cormenzana. Calculation cases are derived from three different types of scenarios: (i) The base scenario that assumes a single initially defective canister located in a cautiously selected canister position, i.e. selecting the failed canister location such that radionuclide release and transport properties are conservative compared to the statistics over all canister locations. Migration processes and parameter values follow the most likely lines of evolution. Repository safety functions are assumed to perform according to the design basis. Calculation cases defined in the Assessment of Radionuclide Release Scenarios report are also supplemented by additional calculation cases that are aimed to study variability between different DFN realisations (additional BS-ALL cases), longitudinal dispersion (BS-RC-ld cases) and alternative realisations of the transport classes along the release paths (BS-RC-tc cases), (ii) Variant scenarios that study declined performance of the repository safety functions. These include enhanced corrosion failure and degradation of the buffer under variant geochemical conditions (iii) Disturbance scenarios that analyse influences of unlikely events on the radionuclide release and migration. Analysis of the variant and disturbance scenarios

Data Publishing and Sharing Via the THREDDS Data Repository

Science.gov (United States)

Wilson, A.; Caron, J.; Davis, E.; Baltzer, T.

2007-12-01

The terms "Team Science" and "Networked Science" have been coined to describe a virtual organization of researchers tied via some intellectual challenge, but often located in different organizations and locations. A critical component to these endeavors is publishing and sharing of content, including scientific data. Imagine pointing your web browser to a web page that interactively lets you upload data and metadata to a repository residing on a remote server, which can then be accessed by others in a secure fasion via the web. While any content can be added to this repository, it is designed particularly for storing and sharing scientific data and metadata. Server support includes uploading of data files that can subsequently be subsetted, aggregrated, and served in NetCDF or other scientific data formats. Metadata can be associated with the data and interactively edited. The THREDDS Data Repository (TDR) is a server that provides client initiated, on demand, location transparent storage for data of any type that can then be served by the THREDDS Data Server (TDS). The TDR provides functionality to: * securely store and "own" data files and associated metadata * upload files via HTTP and gridftp * upload a collection of data as single file * modify and restructure repository contents * incorporate metadata provided by the user * generate additional metadata programmatically * edit individual metadata elements The TDR can exist separately from a TDS, serving content via HTTP. Also, it can work in conjunction with the TDS, which includes functionality to provide: * access to data in a variety of formats via -- OPeNDAP -- OGC Web Coverage Service (for gridded datasets) -- bulk HTTP file transfer * a NetCDF view of datasets in NetCDF, OPeNDAP, HDF-5, GRIB, and NEXRAD formats * serving of very large volume datasets, such as NEXRAD radar * aggregation into virtual datasets * subsetting via OPeNDAP and NetCDF Subsetting services This talk will discuss TDR

Implementing digital preservation in repositories: Knowledge and practices

Directory of Open Access Journals (Sweden)

Caterina Groposo Pavão

2016-09-01

Full Text Available Digital preservation has to be undertaken by institutional repositories, which are responsible for the preservation of the scientific output from academic institutions. However, due to the constant evolution of the field, to gain domain knowledge and recognise best practices is a complex task for people responsible for digital preservation in those institutions. Digital preservation research, practices and solutions address specific problems, such as formats, curation, reference models, authenticity, policies and preservation plans, tools, etc., while stakeholders need an integrated, contextualized and applicable overview. This paper focuses on the implementation of digital preservation in repositories, from the perspective of the team responsible for the project, regarding the necessary knowledge and best practices. Initially, it defines and contextualizes digital preservation repositories. The following section presents a conceptual model of digital preservation, synthesized from conceptual models developed in influential projects in the field, which allows us to identify the domain knowledge in digital preservation. Finally, aspects represented in the model are discussed in the light of the performance of teams implementing digital preservation repositories. It provides recommendations, guides and examples that may be useful for the implementation of digital preservation. It points to the need to strengthen the relationship between domain knowledge in digital preservation repositories with practices developed in numerous projects developed worldwide.

Gas generation and release from the VLJ repository

International Nuclear Information System (INIS)

Vieno, T.; Valkiainen, M.

1992-01-01

The VLJ repository is an underground disposal facility located at the Olkiluoto nuclear power plant site on the west coast of Finland. The repository will house low (LLW) and intermediate level radioactive wastes (MLW) from the TVO I and TVO II BWR's and the spent fuel interim store at Olkiluoto. The disposal rooms have been excavated at a depth of 60... 100 meters in the crystalline bedrock. They consist of two rock silos - one for the LLW and the other for MLW. Low level waste is usually packed in steel drums and steel boxes. Medium level wastes consists of bituminized resins in steel drums. Wastes packages are emplaced in concrete boxes before transportation into the repository. Low level wastes are emplaced in the shotcreted rock silo where no backfilling will used. For medium level wastes, a separate silo of reinforced concrete has been constructed inside the rock silo. No backfilling will be used inside the concrete silo and an opening will be made in the lid of the concrete silo for gas release. The microbial degradation of low level wastes is the principle gas generation process in the repository. The gas transport though the bedrock covering the repository is evaluated with the help of ground water flow study. It is recommended that the shotcrete lining on the ceiling of the repository cavern is partly removed before the final sealing of the repository. Provided that dissipation of gases from the disposal cavern into the rock can been assured, the overall effects of gas generation on the long-term safety of the repository are insignificant. 10 refs., 6 figs

Summary report of first and foreign high-level waste repository concepts

International Nuclear Information System (INIS)

Hanke, P.M.

1987-01-01

Reference repository concepts designs adopted by domestic and foreign waste disposal programs are reviewed. Designs fall into three basic categories: deep borehole from the surface; disposal in boreholes drilled from underground excavations; and disposal in horizontal tunnels or drifts. The repository concepts developed in Sweden, Switzerland, Finland, Canada, France, Japan, United Kingdom, Belgium, Italy, Holland, Denmark, West Germany and the United States are described. 140 refs., 315 figs., 19 tabs

Review. Deep repository for spent nuclear fuel SR 97 - Post-closure safety

International Nuclear Information System (INIS)

Stephansson, Ove

2000-01-01

mechanical development of the respective areas and their place in space and time during the geological evolution of the Baltic Shield. This makes it difficult to rank the suggested sites based on their past, present and future geological evolution. The problem of large discrepancies in data needs to be resolved before stress measurements are performed at future sites. For stress measurements in general and the demand of good quality data at the future sites, there is a need for integrated stress analysis where data from different stress measurements methods (overcoring, hydrofracturing, hydraulic testing of pre-existing fractures and focal mechanism studies) are combined in an integrated stress analysis. Results from orientation of horizontal components from the stress measurements at the three sites clearly demonstrate the relatively large variation in orientation both at each site and between different sites. The relationship between the state of stress and the location and orientation of the major fracture zones is of outmost importance in a future location of a final repository. Preliminary repository layout was constructed by SKB for each selected repository site to accommodate approximately 4,000 canisters. From rock stability point of view the deposition tunnels should be oriented parallel with the orientation of the maximum horizontal principal stress. This is one of the fundamental principles in rock engineering. However, SKB prefer to orient the tunnel axes perpendicular to the maximum stress because the fracture zones and their respect distance, the orientation of water-bearing fracture zones and the area for repository location does not allow a proper tunnel orientation with respect to the orientation of the horizontal rock stresses. The orientation of the tunnels as suggested might lead to spalling or other types of failure of the tunnels and deposition hole. There has been a number of international studies about this problem and SKB has to give this problem

Second generation waste package design and storage concept for the Yucca Mountain Repository

International Nuclear Information System (INIS)

Armijo, Joseph Sam; Kar, Piyush; Misra, Manoranjan

2006-01-01

The reference waste package design and operating mode to be used in the Yucca Mountain Repository is reviewed. An alternate (second generation) operating concept and waste package design is proposed to reduce the risk of localized corrosion of waste packages and to reduce repository costs. The second generation waste package design and storage concept is proposed for implementation after the initial licensing and operation of the reference repository design. Implementation of the second generation concept at Yucca Mountain would follow regulatory processes analogous to those used successfully to extend the design life and uprate the power of commercial light water nuclear reactors in the United States. The second generation concept utilizes the benefits of hot dry storage to minimize the potential for localized corrosion of the waste package by liquid electrolytes. The second generation concept permits major reductions in repository costs by increasing the number of fuel assemblies stored in each waste package, by eliminating the need for titanium drip shields and by fabricating the outer container from corrosion resistant low alloy carbon steel

2012 best practices for repositories collection, storage, retrieval, and distribution of biological materials for research international society for biological and environmental repositories.

Science.gov (United States)

2012-04-01

effective practices are presented for the management of specimen collections and repositories. The term "Best Practice" is used in cases where a level of operation is indicated that is above the basic recommended practice or more specifically designates the most effective practice. It is understood that repositories in certain locations or with particular financial constraints may not be able to adhere to each of the items designated as "Best Practices". Repositories fitting into either of these categories will need to decide how they might best adhere to these recommendations within their particular circumstances. While adherence to ISBER Best Practices is strictly on a voluntary basis, it is important to note that some aspects of specimen management are governed by national/federal, regional and local regulations. The reader should refer directly to regulations for their national/federal, regional and local requirements, as appropriate. ISBER has strived to include terminology appropriate to the various specimen types covered under these practices, but here too, the reader should take steps to ensure the appropriateness of the recommendations to their particular repository type prior to the implementation of any new approaches. Important terms within the document are italicized when first used in a section and defined in the glossary. The ISBER Best Practices are periodically reviewed and revised to reflect advances in research and technology. The third edition of the Best Practices builds on the foundation established in the first and second editions which were published in 2005 and 2008, respectively.

High level radioactive waste repositories. Task 3. Review of underground handling and emplacement. 1. Executive summary

Energy Technology Data Exchange (ETDEWEB)

1981-01-01

A review is presented of proposals for transport, handling and emplacement of high-level radioactive waste in an underground repository appropriate to the U.K. context, with particular reference to waste block size and configuration; self-shielded or partially-shielded block; stages of disposal; transport by road/rail to repository site; handling techniques within repository; emplacement in vertical holes or horizontal tunnels; repository access by adit, incline or shaft; conventional and radiological safety; costs; and major areas of uncertainty requiring research or development.

Evaluation of radiological safety assessment of a repository in a clay rock formation

International Nuclear Information System (INIS)

1999-01-01

This report presents a comprehensive description of the post-closure radiological safety assessment of a repository for the spent fuel arisings resulting from the Spanish nuclear program excavated in a clay host rock formation. In this report three scenarios have been analysed in detail. The first scenario represents the normal in detail. The first scenario represents the normal evolution of the repository (Reference Scenario); and includes a set of variants to investigate the relative importance of the various repository components and examine the sensitivity of the performance to parameters variations. Two altered scenarios have also been considered: deep well construction and poor sealing of the repository. This document contains a detailed description of the repository system, the methodology adopted for the scenarios generation, the process modelling approach and the results of the consequences analysis. (Author)

Coupled processes in repository sealing

International Nuclear Information System (INIS)

Case, J.B.; Kelsall, P.C.

1985-01-01

The significance of coupled processes in repository sealing is evaluated. In most repository designs, shaft seals will be located in areas of relatively low temperature perturbation, in which case the coupling of temperature with stress and permeability may be less significant than the coupling between stress and permeability that occurs during excavation. Constitutive relationships between stress and permeability are reviewed for crystalline rock and rocksalt. These provide a basis for predicting the development of disturbed zones near excavations. Field case histories of the degree of disturbance are presented for two contrasting rock types - Stripa granite and Southeastern New Mexico rocksalt. The results of field investigations in both rock types confirm that hydraulic conductivity or permeability is stress dependent, and that shaft seal performance may be related to the degree that stresses are perturbed and restored near the seal

Electronic repository and standardization of processes and electronic documents in transport

Directory of Open Access Journals (Sweden)

Tomasz DĘBICKI

2007-01-01

Full Text Available The article refers to the idea of the use of electronic repository to store standardised scheme of processes between a Logistics Service Provider and its business partners. Application of repository for automatic or semi-automatic configuration of interoperability in electronic data interchange between information systems of differentcompanies based on transport (road, rail, sea and combined related processes. Standardisation includes processes, scheme of cooperation and related to them, electronic messages.

An Optimal Centralized Carbon Dioxide Repository for Florida, USA

Directory of Open Access Journals (Sweden)

Brandon Poiencot

2011-03-01

Full Text Available For over a decade, the United States Department of Energy, and engineers, geologists, and scientists from all over the world have investigated the potential for reducing atmospheric carbon emissions through carbon sequestration. Numerous reports exist analyzing the potential for sequestering carbon dioxide at various sites around the globe, but none have identified the potential for a statewide system in Florida, USA. In 2005, 83% of Florida’s electrical energy was produced by natural gas, coal, or oil (e.g., fossil fuels, from power plants spread across the state. In addition, only limited research has been completed on evaluating optimal pipeline transportation networks to centralized carbon dioxide repositories. This paper describes the feasibility and preliminary locations for an optimal centralized Florida-wide carbon sequestration repository. Linear programming optimization modeling is used to plan and route an idealized pipeline network to existing Florida power plants. Further analysis of the subsurface geology in these general locations will provide insight into the suitability of the subsurface conditions and the available capacity for carbon sequestration at selected possible repository sites. The identification of the most favorable site(s is also presented.

Radionuclide release from PWR fuels in a reference tuff repository groundwater

International Nuclear Information System (INIS)

Wilson, C.N.; Oversby, V.M.

1985-03-01

The Nevada Nuclear Waste Storage Investigations Project (NNWSI) is studying the suitability of the welded devitrified Topopah Spring tuff at Yucca Mountain, Nye County, Nevada, for potential use as a high-level nuclear waste repository. In support of the Waste Package task of NNWSI, tests have been conducted under ambient air environment to measure radionuclide release from two pressurized water reactor (PWR) spent fuels in water obtained from the J-13 well near the Yucca Mountain site. Four specimen types, representing a range of fuel physical conditions that may exist in a failed waste canister containing a limited amount of water were tested. The specimen types were: fuel rod sections split open to expose bare fuel particles; rod sections with water-tight end fittings with a 2.5-cm long by 150-μm wide slit through the cladding; rod sections with water-tight end fittings and two 200-μm-diameter holes through the cladding; and undefected rod segments with water-tight end fittings. Radionuclide release results from the first 223-day test runs on H.B. Robinson spent fuel specimens in J-13 water are reported and compared to results from a previous test series in which similar Turkey Point reactor spent fuel specimens were tested on deionized water. Selected initial results are also given for Turkey Point fuel specimens tested on J-13 water. Results suggest that the actinides Pu, Am, Cm and Np are released congruently with U as the UO 2 spent fuel matrix dissolves. Fractional release of 137 Cs and 99 Tc was greater than that measured for the actinides. Generally, lower radionuclide releases were measured for the H.B. Robinson fuel in J-13 water than for Turkey Point Fuel in deionized water. 8 references, 7 figures, 9 tables

Mega-conflict project and social complexity - Illustrated by the decision-making on locating a radioactive waste repository in Denmark

DEFF Research Database (Denmark)

Kørnøv, Lone; Lyhne, Ivar; Larsen, Sanne Vammen

2018-01-01

. The process was formally initiated in 2003 when the Danish Parliament gave consent for the government to start preparing a basis for deciding a final repository for Denmark’s low- and intermediate level radioactive waste. After preliminary studies, proposal for a plan for a final repository – and later also...

Performance assessment for Nuclear Power Plant Krsko intermediate and low-level rad-waste repository

International Nuclear Information System (INIS)

Jelavic, V.; Skanata, D.; Plecjas, I.

1990-01-01

Performance safety Assessment for NPP Krsko radwaste repository was performed (LLW/ILW). Shallow land and tunnel type concept were analyzed. Because it was based on two unknown referent sites, one for the shallow land concept and the other for the tunnel type, analysis was generic in nature. Scenario selecting process and consequence analysis were performed by using deterministic approach. Results for both concepts of disposal suggests that proposed NPP Krsko radwaste repository reference site and disposal technology will fully meet radiation limits imposed by the Yugoslav regulations and ICRP guidelines. (author)

High-level waste repository-induced effects

Energy Technology Data Exchange (ETDEWEB)

Leupin, O.X.; Marschall, P.; Johnson, L.; Cloet, V.; Schneider, J. [National Cooperative for the Disposal of Radioactive Waste (NAGRA), Wettingen (Switzerland); Smith, P. [Safety Assessment Management Ltd, Henley-On-Thames, Oxfordshire (United Kingdom); Savage, D. [Savage Earth Associates Ltd, Bournemouth, Dorset (United Kingdom); Senger, R. [Intera Inc., Ennetbaden (Switzerland)

2016-10-15

This status report aims at describing and assessing the interactions of the radioactive waste emplaced in a high-level waste (HLW) repository with the engineered materials and the Opalinus Clay host rock. The Opalinus Clay has a thickness of about 100 m in the proposed siting regions. Among other things the results are used to steer the RD and D programme of NAGRA. The repository-induced effects considered in this report are of the following broad types: - Thermal effects: i.e. effects on the host rock and engineered barriers arising principally from the heat generated by the waste. - Rock-mechanical effects: i.e. effects arising from the mechanical disturbance to the rock caused by the excavation of the emplacement rooms and other underground structures. - Hydraulic and gas-related effects: i.e. the effects of repository resaturation and of gas generation, e.g. due to the corrosion of metals within the repository, on the host rock and engineered barriers. - Chemical effects: i.e. chemical interactions between the waste, the engineered materials and the host rock, with a focus on chemical effects of the waste and engineered materials on the host rock. The assessment of the repository-induced effects shows that detrimental chemical and mechanical impacts are largely confined to the rock immediately adjacent to the excavations, thermal impacts are controllable by limiting the heat load and gas effects are limited by ensuring acceptably low gas production rates and by the natural tendency of the gas to escape along the excavations and the excavation damaged zone (EDZ) rather than through the undisturbed rock. Specific measures that are part of the current reference design are discussed in relation to their significance with respect to repository-induced effects. The SF/HLW emplacement rooms (emplacement drifts) are designed, constructed, operated and finally backfilled in such a way that formation of excavation damaged zones is limited. Specifically this is achieved

High-level waste repository-induced effects

International Nuclear Information System (INIS)

Leupin, O.X.; Marschall, P.; Johnson, L.; Cloet, V.; Schneider, J.; Smith, P.; Savage, D.; Senger, R.

2016-10-01

This status report aims at describing and assessing the interactions of the radioactive waste emplaced in a high-level waste (HLW) repository with the engineered materials and the Opalinus Clay host rock. The Opalinus Clay has a thickness of about 100 m in the proposed siting regions. Among other things the results are used to steer the RD and D programme of NAGRA. The repository-induced effects considered in this report are of the following broad types: - Thermal effects: i.e. effects on the host rock and engineered barriers arising principally from the heat generated by the waste. - Rock-mechanical effects: i.e. effects arising from the mechanical disturbance to the rock caused by the excavation of the emplacement rooms and other underground structures. - Hydraulic and gas-related effects: i.e. the effects of repository resaturation and of gas generation, e.g. due to the corrosion of metals within the repository, on the host rock and engineered barriers. - Chemical effects: i.e. chemical interactions between the waste, the engineered materials and the host rock, with a focus on chemical effects of the waste and engineered materials on the host rock. The assessment of the repository-induced effects shows that detrimental chemical and mechanical impacts are largely confined to the rock immediately adjacent to the excavations, thermal impacts are controllable by limiting the heat load and gas effects are limited by ensuring acceptably low gas production rates and by the natural tendency of the gas to escape along the excavations and the excavation damaged zone (EDZ) rather than through the undisturbed rock. Specific measures that are part of the current reference design are discussed in relation to their significance with respect to repository-induced effects. The SF/HLW emplacement rooms (emplacement drifts) are designed, constructed, operated and finally backfilled in such a way that formation of excavation damaged zones is limited. Specifically this is achieved

Corrosion phase formation on container alloys in basalt repository environments

International Nuclear Information System (INIS)

Johnston, R.G.; Anantatmula, R.P.; Lutton, J.M.; Rivera, C.L.

1986-01-01

The Basalt Waste Isolation Project is evaluating the suitability of basalt in southeastern Washington State as a possible location for a nuclear waste repository. The performance of the waste package, which includes the waste form, container, and surrounding packing material, will be affected by the stability of container alloys in the repository environment. Primary corrosion phases and altered packing material containing metals leached from the container may also influence subsequent reactions between the waste form and repository environment. Copper- and iron-based alloys were tested at 50 0 to 300 0 C in an air/steam environment and in pressure vessels in ground-water-saturated basalt-bentonite packing material. Reaction phases formed on the alloys were identified and corrosion rates were measured. Changes in adhering packing material were also evaluated. The observed reactions and their possible effects on container alloy durability in the repository are discussed

Retrievability as proposed in the US repository concept

International Nuclear Information System (INIS)

Harrington, P.G.

2000-01-01

The Nuclear Waste Policy Act states that any repository shall be designed and constructed to permit retrieval. Reasons for retrieval include public health and safety, environmental concerns, and recovery of economically valuable contents of spent nuclear fuel. The Nuclear Regulatory Commission requires that waste must be retrievable at any time up to 50 years after start of emplacement. The US Department of Energy intends to maintain a retrieval capability throughout the preclosure period. Possible preclosure periods range from a minimum of 50 years to as much as 300 years. Repository closure includes sealing all accessible portions of the repository, including ventilation shafts, access ramps and boreholes. Drip shields will be installed over the waste packages. Access to the repository after closure is not intended. The proposed repository includes horizontal emplacement drifts located in the unsaturated zone. The emplacement drift centerline spacing is 81 meters to provide a subboiling region between drifts for water drainage. A drip shield covers the waste packages. All emplacement drifts remain open until closure of the repository, providing performance benefits such as removing heat and moisture during the preclosure period and lowering postclosure temperatures. This does not impede retrieval, permitting a reversal of the emplacement process to accomplish retrieval under normal conditions. The preclosure period is therefore not to enhance retrievability, but does improve performance, and the resultant extension of the retrievability capability is a secondary effect. Information must be provided from the performance confirmation program to support a regulatory decision to close. Closure would isolate the repository from the accessible environment, preclude preferential flowpaths for water into the mountain, and minimize the possibility of inadvertent intrusion. (author)

DataONE: Gateway to Earth and Environmental Data Repositories

Science.gov (United States)

Koskela, R.; Michener, W. K.; Vieglais, D.; Budden, A. E.

2017-12-01

DataONE (Data Observation Network for Earth) is a National Science Foundation DataNet project that enables universal access to data and also facilitates researchers in fulfilling their need for data management and in providing secure and permanent access to their data. DataONE offers the scientific community a suite of tools and training materials that cover all aspects of the data life cycle from data collection, to management, analysis and publication. Data repositories affiliated with DataONE are referred to as Member Nodes and represent large regional, national and international research networks, agencies, and other institutions. As part of the DataONE Federation, the repositories gain access to a range of value-added services to support their users. These services include usage tracking and reporting, content replication, and the ability to register the services created by the repository. In addition, DataONE and the California Digital Library manage ONEShare, a repository that accepts content submitted through Dash, a platform allowing researchers to easily describe, deposit and share their research data.

Audit and Certification Process for Science Data Digital Repositories

Science.gov (United States)

Hughes, J. S.; Giaretta, D.; Ambacher, B.; Ashley, K.; Conrad, M.; Downs, R. R.; Garrett, J.; Guercio, M.; Lambert, S.; Longstreth, T.; Sawyer, D. M.; Sierman, B.; Tibbo, H.; Waltz, M.

2011-12-01

Science data digital repositories are entrusted to ensure that a science community's data are available and useful to users both today and in the future. Part of the challenge in meeting this responsibility is identifying the standards, policies and procedures required to accomplish effective data preservation. Subsequently a repository should be evaluated on whether or not they are effective in their data preservation efforts. This poster will outline the process by which digital repositories are being formally evaluated in terms of their ability to preserve the digitally encoded information with which they have been entrusted. The ISO standards on which this is based will be identified and the relationship of these standards to the Open Archive Information System (OAIS) reference model will be shown. Six test audits have been conducted with three repositories in Europe and three in the USA. Some of the major lessons learned from these test audits will be briefly described. An assessment of the possible impact of this type of audit and certification on the practice of preserving digital information will also be provided.

SR 97 - Waste, repository design and sites. Background report to SR 97 SKB

International Nuclear Information System (INIS)

1999-10-01

SR 97 is a comprehensive analysis of long-term safety of a deep repository for spent nuclear fuel. The repository is assumed to be designed according to the KBS-3 method. Assessments are performed in SR 97 for three fictitious sites: Aberg, Beberg and Ceberg. One premise is that data used for assessment of the fictitious sites are to be taken from sites that have previously been investigated. The spent nuclear fuel is enclosed in copper canisters with an insert of cast iron. The canisters are emplaced in bored holes in the floor of the deposition tunnels. Around each canister, bentonite blocks are stacked which, after absorbing water and swelling, will isolate the canister from groundwater, hold the canister in place and retard transport of radionuclides from the canister to the surrounding rock. The spent nuclear fuel will emit heat for a long time, due to the decay heat. The maximum permissible temperature on the canister surface has been chosen at 100 deg C. The spacing between the deposition holes and between the deposition tunnels is adjusted site-specifically to meet this requirement. The thermal properties of the rock and the buffer material are of importance for how closely the deposition holes and tunnels can be spaced. After deposition, the deposition tunnels are backfilled with a mixture of bentonite and crushed rock. SR 97 examines above all the consequences of various scenarios and the handling of various types of uncertainties. The different repository sites illustrate normal properties for Swedish bedrock which are of importance for safety. To facilitate the work, the repositories on the three sites are configured as similarly as possible, which means for example that they are located at roughly the same depth and are fitted into the bedrock in a relatively similar fashion. Apart from the siting of a repository for spent nuclear fuel, the site may need to house a separate repository for other long-lived waste. This possibility has been considered in

SR 97 - Waste, repository design and sites. Background report to SR 97 SKB

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-10-01

SR 97 is a comprehensive analysis of long-term safety of a deep repository for spent nuclear fuel. The repository is assumed to be designed according to the KBS-3 method. Assessments are performed in SR 97 for three fictitious sites: Aberg, Beberg and Ceberg. One premise is that data used for assessment of the fictitious sites are to be taken from sites that have previously been investigated. The spent nuclear fuel is enclosed in copper canisters with an insert of cast iron. The canisters are emplaced in bored holes in the floor of the deposition tunnels. Around each canister, bentonite blocks are stacked which, after absorbing water and swelling, will isolate the canister from groundwater, hold the canister in place and retard transport of radionuclides from the canister to the surrounding rock. The spent nuclear fuel will emit heat fora long time, due to the decay heat. The maximum permissible temperature on the canister surface has been chosen at 100 deg C. The spacing between the deposition holes and between the deposition tunnels is adjusted site-specifically to meet this requirement. The thermal properties of the rock and the buffer material are of importance for how closely the deposition holes and tunnels can be spaced. After deposition, the deposition tunnels are backfilled with a mixture of bentonite and crushed rock. SR 97 examines above all the consequences of various scenarios and the handling of various types of uncertainties. The different repository sites illustrate normal properties for Swedish bedrock which are of importance for safety. To facilitate the work, the repositories on the three sites are configured as similarly as possible, which means for example that they are located at roughly the same depth and are fitted into the bedrock in a relatively similar fashion. Apart from the siting of a repository for spent nuclear fuel, the site may need to house a separate repository for other long-lived waste. This possibility has been considered in

The projected environmental impacts of transportation of radioactive material to the first United States repository site

International Nuclear Information System (INIS)

Cashwell, J.W.; Neuhauser, K.S.; Reardon, P.C.; McNair, G.W.

1987-01-01

The relative national environmental impacts of transporting spent fuel and other nuclear wastes to each of 9 candidate repository sites in the United States were analyzed for the 26-year period of repository operation. Two scenarios were examined for each repository: 1) shipment of 5-year-old spent fuel and Defence High-Level Waste (DHLW) directly from their points of origin to a repository (reference case); and 2) shipment of 5-year-old spent fuel to a Monitored Retrievable Storage (MRS) facility and shipment (by dedicated rail) of 10-year-old consolidated spent fuel from the MRS to a repository. Transport by either all truck or all rail from the points of origin were analyzed as bounding cases. The computational system used to analyze these impacts included the WASTES II logistics code and the RADTRAN III risk analysis code. The radiological risks for the reference case increased as the total shipment miles to a repository increased for truck; the risks also increased with mileage for rail but at a lower rate. For the MRS scenario the differences between repository sites were less pronounced for both modal options, because of the reduction in total shipment miles possible with the large dedicated rail casks. All the risks reported are small in comparison to the radiological risks due to 'natural background'

Preliminary assessment of nuclear waste transportation cost and risk for operation of the first repository at candidate sites

International Nuclear Information System (INIS)

Peterson, R.W.; McSweeney, T.I.; Varadarajan, R.V.; Wilmot, E.L.; Cashwell, J.W.; Joy, D.S.

1983-01-01

To support the selection of the first commercial nuclear waste repository site in 1987, environmental analyses of five candidate site locations are currently being performed. The five locations are in the Gulf Interior Region, the Permian Basin, the Paradox Basin, Yucca Mountain and the Hanford reservation. Costs and operational risks associated with the transportation of nuclear wastes to a single repository located in these regions have been calculated for a life-cycle of 26 years

Application Research of Horn Array Multi-Beam Antenna in Reference Source System for Satellite Interference Location

Science.gov (United States)

Zhou, Ping; Lin, Hui; Zhang, Qi

2018-01-01

The reference source system is a key factor to ensure the successful location of the satellite interference source. Currently, the traditional system used a mechanical rotating antenna which leaded to the disadvantages of slow rotation and high failure-rate, which seriously restricted the system’s positioning-timeliness and became its obvious weaknesses. In this paper, a multi-beam antenna scheme based on the horn array was proposed as a reference source for the satellite interference location, which was used as an alternative to the traditional reference source antenna. The new scheme has designed a small circularly polarized horn antenna as an element and proposed a multi-beamforming algorithm based on planar array. Moreover, the simulation analysis of horn antenna pattern, multi-beam forming algorithm and simulated satellite link cross-ambiguity calculation have been carried out respectively. Finally, cross-ambiguity calculation of the traditional reference source system has also been tested. The comparison between the results of computer simulation and the actual test results shows that the scheme is scientific and feasible, obviously superior to the traditional reference source system.

Terminology development towards harmonizing multiple clinical neuroimaging research repositories.

Science.gov (United States)

Turner, Jessica A; Pasquerello, Danielle; Turner, Matthew D; Keator, David B; Alpert, Kathryn; King, Margaret; Landis, Drew; Calhoun, Vince D; Potkin, Steven G; Tallis, Marcelo; Ambite, Jose Luis; Wang, Lei

2015-07-01

Data sharing and mediation across disparate neuroimaging repositories requires extensive effort to ensure that the different domains of data types are referred to by commonly agreed upon terms. Within the SchizConnect project, which enables querying across decentralized databases of neuroimaging, clinical, and cognitive data from various studies of schizophrenia, we developed a model for each data domain, identified common usable terms that could be agreed upon across the repositories, and linked them to standard ontological terms where possible. We had the goal of facilitating both the current user experience in querying and future automated computations and reasoning regarding the data. We found that existing terminologies are incomplete for these purposes, even with the history of neuroimaging data sharing in the field; and we provide a model for efforts focused on querying multiple clinical neuroimaging repositories.

Learning Object Repositories

Science.gov (United States)

Lehman, Rosemary

2007-01-01

This chapter looks at the development and nature of learning objects, meta-tagging standards and taxonomies, learning object repositories, learning object repository characteristics, and types of learning object repositories, with type examples. (Contains 1 table.)

A Nuclide Release Model for a Deep Well Scenario near a Repository

International Nuclear Information System (INIS)

Lee, Youn Myoung; Jung, Jong Tae; Choi, Jong Won

2010-01-01

Recently several template programs ready for the safety assessment of a high-level radioactive waste repository (HLW) and a low- and intermediate level radioactive waste repository (LILW) systems, that are conceptually modeled, have been developed by utilizing GoldSim and AMBER at KAERI. During the last few years, such template programs have been utilized for the evaluation of nuclide transports in the nearand far-field of a repository as well as transport through the biosphere under various normal and disruptive release scenarios with assumed data. The GoldSim program, another template program by which influence due to a well located very near to the repository has been modeled and evaluated for an assumed case in order to simulate the worst exposure scenario. This seems very useful to evaluate an accidental event a long time after closure of the repository has been developed and illustrated

Region-to-area screening methodology for the crystalline repository project

International Nuclear Information System (INIS)

1984-08-01

The ''Nuclear Waste Policy Act of 1982'' (NWPA), enacted January 7, 1983 as Public Law 97-425, confirmed the responsibility of the US Department of Energy (DOE) for management of high-level radioactive waste. The NWPA directed the DOE to provide safe facilities for isolation of high-level radioactive waste from the environment in federally owned and federally licensed repositories. To achieve the goals of providing licensed repositories for high-level radioactive waste, a technical program has been developed by the DOE to meet all relevant radiological protection criteria and other requirements. By March 1987, the NWPA requires the DOE to recommend to the President a single site, chosen from five nominated sites for construction of the first repository. Rock types being considered as potential hosts for the first repository include salt, basalt, and tuff. The NWPA also requires the DOE to select three candidate sites, chosen from five nominated sites to be recommended to the President by July 1989, as possible locations for the second repository. Potential host rock types for the second federal repository will include crystalline rock. This document outlines the methodology for region-to-area screening of exposed crystalline rock bodies for suitability as sites for further study. 17 refs., 14 figs., 2 tabs

INIS: Nuclear Grey Literature Repository

International Nuclear Information System (INIS)

Savić, Dobrica

2016-01-01

As one of the world's largest collections of published information on the peaceful uses of nuclear science and technology, INIS represents an extraordinary example of world cooperation. Currently, as INIS members, 130 countries and 24 international organizations share and allow access to their valuable nuclear information resources, preserving them for future generations and offering a freely available nuclear knowledge repository. Since its creation in 1970, INIS has collected and provided access to more than 3.8 million bibliographic references to publications, documents, technical reports, non-copyrighted documentation, and other grey literature, as well as over a million full texts. Public interest throughout the years in accessing the INIS Collection has been remarkable. This paper deals with the challenges faced by INIS in its endeavour to increase the use, accessibility, usability and expandability of its on-line repository. It also describes document collection, the features and characteristics of implementing a new search engine, as well as the lessons learned. (author)

Twenty years' experience with shallow ground repositories in India

International Nuclear Information System (INIS)

Balu, K.; Mohan, A.L.; Narayan, P.K.; Godse, V.B.; Sunder Rajan, N.S.

1984-01-01

With the setting up of the Bhabha Atomic Research Centre at Trombay, the first nuclear research centre in India, more than two decades ago, the need arose for disposal of the country's low-level radioactive solid wastes. Since then, nuclear power stations and other nuclear installations have been set up in different locations and the major mode of disposal for low-level solid wastes has been in engineered facilities in shallow land. The paper presents an overview of the Indian experience, with shallow land repositories for low-active solid wastes, from the point of view of design, operation and surveillance, at a number of sites. The influence of site characteristics on the design of the repository and the underground disposal modules is discussed. Details of the pre-operational investigations performed at different sites and the scheme for monitoring and surveillance of operating repositories are also included. The paper also presents briefly the type of safety analysis being carried out to evaluate possible environmental impact due to the operation of the shallow land repositories. (author)

Review of Y/OWI/TM-36: repository design performance in salt, granite, shale or basalt

International Nuclear Information System (INIS)

Talbot, R.; Nair, O.B.

1979-09-01

As part of the ongoing work by the Lawrence Livermore Laboratory to evaluate repository design performance, this memorandum presents a review of the preconceptual repository design described in Y/OWI/TM-36, Technical Support for GEIS: Radioactive Waste Isolation in Geologic Formations, April 1978. The purpose of this review is: to assess the adequacy of the design procedures and assumptions; to identify inappropriate or unsubstantiated design issues; to identify areas where additional numerical analyses may be required; and to develop data for inclusion in a reference repository design. The preconceptual repository design is presented in the form of 23 volumes of data base, analyses, and design layouts for four rock types: bedded salt, shale, granite and basalt. This memorandum reviews all four repository designs

Deep geologic repository for low and intermediate radioactive level waste in Canada

International Nuclear Information System (INIS)

Liu Jianqin; Li Honghui; Sun Qinghong; Yang Zhongtian

2012-01-01

Ontario Power Generation (OPG) is undergoing a project for the long-term management of low and intermediate level waste (LILW)-a deep geologic repository (DGR) project for low and intermediate level waste. The waste source term disposed, geologic setting, repository layout and operation, and safety assessment are discussed. It is expected to provide reference for disposal of low and intermediate level waste that contain the higher concentration of long-lived radionuclides in China. (authors)

Development of site selection process for an LILW repository in Slovenia

International Nuclear Information System (INIS)

Zeleznik, N.; Kralj, M.; Mele, I.; Veselic, M.

2005-01-01

The activities regarding the LILW repository site selection in Slovenia are planned to meet the requirements of the Act on Ionising Radiation Protection and Nuclear Safety, especially the requirement that the site for a repository should be selected by 2008 and the repository should be in operation by 2013. In November 2004, the official administrative procedure for the siting of the repository started with the first spatial public conference on spatial planning procedure. It was carried out by the Ministry of the Environment and Spatial Planning and ARAO. Immediately after the conference the Program for the preparation of the detailed plan of national importance for the LILW repository was accepted by the Ministry. At the beginning of December 2004, ARAO invited all Slovenian local communities to participate in the site selection process and volunteer a site or area in their local community for further investigation. At the beginning of April 2005 the first phase of the bidding process was concluded. ARAO received applications from eight local communities. A pre-feasibility study to define three of the most promising locations was conducted because only three locations are foreseen by the Program for the preparation of the detailed plan of national importance. Methodologies were prepared for assessment of different parameters of technical, financial, environmental and spatial suitability as well as public acceptability. Comparative, preferential and also exclusion criteria for the respective parameters were defined. The results of the cabinet and fieldwork research were compared and further assessed in order to obtain maximum three local communities with three potential sites in which the probability of siting the LILW repository seems to be the highest. Detailed plans of national importance will be prepared for these sites. (author)

Repository Rodeo Redux

CERN Document Server

Anez, Melissa; Donohue, Tim; Fyson, Will; Simko, Tibor; Wilcox, David

2017-01-01

You’ve got more repository questions and we’ve got more answers! Last year’s Repository Rodeo panel was a huge success, so we’re taking the show on the road to Brisbane for OR2017. Join representatives from the DSpace, Eprints, Fedora, Hydra, and Islandora communities as we (briefly) explain what each of our repositories actually does. We'll also talk about the directions of our respective technical and community developments, and related to the conference theme of Open: Innovation Knowledge Repositories, offer brief observations about the latest, most promising and/or most surprising innovations in our space. This panel will be a great opportunity for newcomers to Open Repositories to get a crash course on the major repository options and meet representatives from each of their communities. After a brief presentation from each representative, we'll open the session up for questions from the audience.

Characterization Plan for L/ILW Repository Candidate Sites in Croatia

International Nuclear Information System (INIS)

Schaller, A.; Lokner, V.; Kucar-Dragicevic, S.; Subasic, D.

1998-01-01

There have been four preferred sites for L/ILW repository selected in the siting program in Croatia so far. According to the accepted and verified site selection procedure, these sites are suitable for a more detailed characterization, including also site specific field investigations. The aim of these investigations is to measure and calculate all needed site specific parameters important for performance of safety assessment, aiming eventually with selection of the final disposal site. Both Croatian and IAEA regulations referring to radwaste repository siting procedure have been briefly discussed. Detailed site investigations foreseen to be done in order to perform a successful site characterization, refer to the following main topics: geomorphology, lithostratigraphy, tectonics, seismicity, rock mechanics, surface-water hydrology, aquifer features and groundwater hydrology, rock and groundwater chemistry, and radionuclide transport modeling. All these issues are listed in suggested site characterization format. (author)

Preliminary analyses of scenarios for potential human interference for repositories in three salt formations

International Nuclear Information System (INIS)

1985-10-01

Preliminary analyses of scenarios for human interference with the performance of a radioactive waste repository in a deep salt formation are presented. The following scenarios are analyzed: (1) the U-Tube Connection Scenario involving multiple connections between the repository and the overlying aquifer system; (2) the Single Borehole Intrusion Scenario involving penetration of the repository by an exploratory borehole that simultaneously connects the repository with overlying and underlying aquifers; and (3) the Pressure Release Scenario involving inflow of water to saturate any void space in the repository prior to creep closure with subsequent release under near lithostatic pressures following creep closure. The methodology to evaluate repository performance in these scenarios is described and this methodology is applied to reference systems in three candidate formations: bedded salt in the Palo Duro Basin, Texas; bedded salt in the Paradox Basin, Utah; and the Richton Salt Dome, Mississippi, of the Gulf Coast Salt Dome Basin

EEI/UWASTE oversight of the DOE Repository Program by the Repository Information Exchange Team

International Nuclear Information System (INIS)

Henkel, C.J.; Supko, E.M.; Schwartz, M.H.

1993-01-01

The Utility Nuclear Waste and Transportation Program of the Edison Electric Institute (EEI/UWASTE) has conducted reviews of the US DOE's repository program through its Repository Information Exchange Team (RIET or Team). Eight such reviews have been conducted since 1985 covering topics that include repository program management and control; repository schedule; repository budget; quality assurance; site characterization; repository licensing; environmental issues; and institutional and public information activities. The utility industry has used these repository program reviews as a forum for providing DOE's Office of Civilian Radioactive Waste Management (OCRWM) with comments on the direction of the repository program, advice for future actions regarding quality assurance activities and repository licensing, and suggestions for management and control of the Repository Program. The most significant recommendations made by the utility industry through the RIET are discussed along with any subsequent action by OCRWM in response to or subsequent to utility industry recommendations. The process used by the RIET to develop its recommendations to OCRWM regarding the repository program is also discussed

Locations of serial reach targets are coded in multiple reference frames.

Science.gov (United States)

Thompson, Aidan A; Henriques, Denise Y P

2010-12-01

Previous work from our lab, and elsewhere, has demonstrated that remembered target locations are stored and updated in an eye-fixed reference frame. That is, reach errors systematically vary as a function of gaze direction relative to a remembered target location, not only when the target is viewed in the periphery (Bock, 1986, known as the retinal magnification effect), but also when the target has been foveated, and the eyes subsequently move after the target has disappeared but prior to reaching (e.g., Henriques, Klier, Smith, Lowy, & Crawford, 1998; Sorrento & Henriques, 2008; Thompson & Henriques, 2008). These gaze-dependent errors, following intervening eye movements, cannot be explained by representations whose frame is fixed to the head, body or even the world. However, it is unknown whether targets presented sequentially would all be coded relative to gaze (i.e., egocentrically/absolutely), or if they would be coded relative to the previous target (i.e., allocentrically/relatively). It might be expected that the reaching movements to two targets separated by 5° would differ by that distance. But, if gaze were to shift between the first and second reaches, would the movement amplitude between the targets differ? If the target locations are coded allocentrically (i.e., the location of the second target coded relative to the first) then the movement amplitude should be about 5°. But, if the second target is coded egocentrically (i.e., relative to current gaze direction), then the reaches to this target and the distances between the subsequent movements should vary systematically with gaze as described above. We found that requiring an intervening saccade to the opposite side of 2 briefly presented targets between reaches to them resulted in a pattern of reaching error that systematically varied as a function of the distance between current gaze and target, and led to a systematic change in the distance between the sequential reach endpoints as predicted by

Impact of transporting defense high-level waste to a geologic repository

International Nuclear Information System (INIS)

Joy, D.S.; Shappert, L.B.; Boyle, J.W.

1984-12-01

The Nuclear Waste Policy Act of 1982 (Public Law 97-425) provides for the development of repositories for the disposal of high-level radioactive waste and spent nuclear fuel and requires the Secretary of Energy to evaluate five potential repository sites. One factor that is to be examined is transportation of radioactive materials to such a repository and whether transportation might be affected by shipments to a defense-only repository, or to one that accepts both defense and commercial waste. In response to this requirement, The Department of Energy has undertaken an evaluation of the cost and risk associated with the potential shipments. Two waste-flow scenarios are considered which are related to the total quantity of defense high-level waste which will be placed in a repository. The low-flow case is based on a total of 6700 canisters being transported from one site, while the high-flow case assumes that a total of 20,000 canisters will be transported from three sites. For the scenarios considered, the estimated shipping costs range from $105 million to $257 million depending upon the mode of transport and the repository location. The total risks associated with shipping defense high-level waste to a repository are estimated to be significantly smaller than predicted for other transportation activities. In addition, the cost of shipping defense high-level waste to a repository does not depend on whether the site is a defense-only or a commercial repository. Therefore, the transportation considerations are not a basis for the selection of one of the two disposal options

Prototype Repository. Tracer dilution tests during operation phase, test campaign 3

Energy Technology Data Exchange (ETDEWEB)

Harrstroem, Johan; Andersson, Peter (Geosigma AB (Sweden))

2010-05-15

The Prototype Repository project is focused on testing and demonstrating the function of the SKB deep repository system. The third tracer dilution campaign during the Prototype Repository operation period was performed in January 2010. The purpose was to estimate the groundwater flows and hydraulic gradients in the boreholes vicinity and will function as a reference for comparison with results from modeling and prior assumptions. The test campaign consisted of tracer dilution tests in 13 different borehole sections. Each test consisted of approximately 15-55 min tracer injection time and about 1-3 days dilution test time depending on the transmissivity of the test section. The data interpretation also included estimates of the local hydraulic gradients in the vicinity of the borehole sections

Aspects of igneous activity significant to a repository at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Krier, D.J.; Perry, F.V.

2004-01-01

Location, timing, volume, and eruptive style of post-Miocene volcanoes have defined the volcanic hazard significant to a proposed high-level radioactive waste (HLW) and spent nuclear fuel (SNF) repository at Yucca Mountain, Nevada, as a low-probability, high-consequence event. Examination of eruptive centers in the region that may be analogueues to possible future volcanic activity at Yucca Mountain have aided in defining and evaluating the consequence scenarios for intrusion into and eruption above a repository. The probability of a future event intersecting a repository at Yucca Mountain has a mean value of 1.7 x 10 -8 per year. This probability comes from the Probabilistic Volcanic Hazard Assessment (PVHA) completed in 1996 and updated to reflect change in repository layout. Since that time, magnetic anomalies representing potential buried volcanic centers have been identified fiom magnetic surveys; however these potential buried centers only slightly increase the probability of an event intersecting the repository. The proposed repository will be located in its central portion of Yucca Mountain at approximately 300m depth. The process for assessing performance of a repository at Yucca Mountain has identified two scenarios for igneous activity that, although having a very low probability of occurrence, could have a significant consequence should an igneous event occur. Either a dike swarm intersecting repository drifts containing waste packages, or a volcanic eruption through the repository could result in release of radioactive material to the accessible environment. Ongoing investigations are assessing the mechanisms and significance of the consequence scenarios. Lathrop Wells Cone (∼80,000 yrs), a key analogue for estimating potential future volcanic activity, is the youngest surface expression of apparent waning basaltic volcanism in the region. Cone internal structure, lavas, and ash-fall tephra have been examined to estimate eruptive volume, eruption

Final repository for spent nuclear fuel in granite - the KBS-3V concept in Sweden and Finland

International Nuclear Information System (INIS)

Pettersson, Stig; Loennerberg, Bengt

2008-01-01

Both Sweden and Finland has advanced plans for design, construction and operation of the final repositories for direct disposal of spent nuclear fuel. Both countries have the same type of host rock - granite. They are also investigating alternative concept for disposal, vertical or horizontal disposal of the canisters with encapsulated spent nuclear fuel, normally called KBS-3V or the KBS-3H disposal concept. The development of the KBS-3V concept started around 1980 and is the reference method for both SKB in Sweden and Posiva in Finland. However, extensive development work is ongoing since 2001 with KBS-3H in order to bring that concept to the same maturity as KBS-3V. This presentation deals with the design and operation of the KBS-3V based on the work done within Sweden and SKB but the development is Finland is identical and it is a close cooperation between SKB in Sweden and Posiva in Finland. In Sweden, the site investigation for location of the repository has been concentrated on two sites, in the Oskarshamn area, about 350 km south of Stockholm, and the Forsmark area, about 180 km north of Stockholm. For information it can be mentioned that Finland plans to locate their repository in the vicinity of the Olkiluoto nuclear power plant site, about 300 km north of Helsinki. The site investigation is completed and the selection of site is scheduled to mid 2009 and sending in the application for location and construction of the repository is scheduled to end 2009. After receiving all necessary permits, construction time and commissioning will take about 7 to 8 years and operation is expected to start about 2020. The KBS-3 system is based on a multi barrier concept and the work with compiling the design requirements for the underground part of the deep repository has been ongoing for some time within the SKB organisation. Today the design requirements for the underground part are documented in a big number of reports that has been produced by specialists and working

Rapid Advance Tunnelling with special reference to its implications for repository excavation

International Nuclear Information System (INIS)

Parkes, D.B.

1986-02-01

The feasibility of Rapid Advance Tunnelling techniques was examined for application to the construction of radioactive waste repositories. A study of information provided by clients, consulting engineers and contractors engaged in tunnelling operations on over sixty international projects was analysed. A report is given, based on this data, and reveals a wide range of levels of performances. The findings suggest that Rapid Advance Tunnelling is likely to satisfy the special requirements for stability needed for long-term storage of radioactive waste. (U.K.)

Referred pain location depends on the affected section of the sacroiliac joint.

Science.gov (United States)

Kurosawa, Daisuke; Murakami, Eiichi; Aizawa, Toshimi

2015-03-01

Pain referred from the sacroiliac joint (SIJ) may originate in the joint's posterior ligamentous region. The site of referred pain may depend on which SIJ section is affected. This study aimed to determine the exact origin of pain referred from four SIJ sections. The study included 50 patients with SIJ dysfunction, confirmed by more than 70 % pain relief after periarticular injection of local anesthetic into the SIJ. The posterior SIJ was divided into four sections-upper, middle, lower, and other (cranial portion of the ilium outside the SIJ)-designated sections 1, 2, 3, and 0, respectively. We then inserted a needle into the periarticular SIJ under fluoroscopy. After the patient identified the area(s) in which the needle insertion produced referred pain, we injected a mixture of 2 % lidocaine and contrast medium into the corresponding SIJ section. Referred pain from SIJ section 0 was mainly located in the upper buttock along the iliac crest; pain from section 1, around the posterosuperior iliac spine; pain from section 2, in the middle buttock area; pain from section 3, in the lower buttock. In all, 22 (44.0 %) patients complained of groin pain, which was slightly relieved by lidocaine injection into SIJ sections 1 and 0. Dysfunctional upper sections of the SIJ are associated with pain in the upper buttock and lower sections with pain in the lower buttock. Groin pain might be referred from the upper SIJ sections.

Safety analysis of the proposed Canadian geologic nuclear waste repository

International Nuclear Information System (INIS)

Prowse, D.R.

1977-01-01

The Canadian program for development and qualification of a geologic repository for emplacement of high-level and long-lived, alpha-emitting waste from irradiated nuclear fuel has been inititiated and is in its initial development stage. Fieldwork programs to locate candidate sites with suitable geological characteristics have begun. Laboratory studies and development of models for use in safety analysis of the emplaced nuclear waste have been initiated. The immediate objective is to complete a simplified safety analysis of a model geologic repository by mid-1978. This analysis will be progressively updated and will form part of an environmental Assessment Report of a Model Fuel Center which will be issued in mid-1979. The long-term objectives are to develop advanced safety assessment models of a geologic repository which will be available by 1980

Repository development status in Spain

Energy Technology Data Exchange (ETDEWEB)

Rodriguez Beceiro, Alvaro; Zuloaga, Pablo [ENRESA (Spain)

2009-06-15

The paper describes the status of repository development for the different waste categories. Low and Intermediate Waste Disposal facility of El Cabril was commissioned in 1992 and is in normal operation. The major modifications and activities during the last years are the adaptation to waste streams not initially foreseen such as some decommissioning waste or waste from steel industry, and the improvement of its performance assessment, supported by a R and D and refined models. As part of this facility, a new disposal facility specifically intended for very low activity waste has been constructed and commissioned in July 2008. Its design is based on the European Directive for hazardous waste disposal. National policy for Nuclear Spent Fuel and High-Level waste is focused on the development of a centralized storage facility of the vault type, whose site location would be selected through a volunteering process. Meanwhile, with the aim of solving specific problems, three individual storage facilities are in different status at reactor sites. Research on final solution, including some repository aspects as well as separation and transmutation are being carried out in accordance to ENRESA's R and D program. ENRESA has developed conceptual designs for non site specific repositories, both in granite and clay, and has carried out their corresponding performance assessment exercises. (authors)

Monitoring system specifications: retrieval of surf from a salt repository

International Nuclear Information System (INIS)

1980-01-01

The task of developing specifications for a reference monitoring system determined by repository environmental conditions, retrieval operations, and federal regulatory criteria is discussed. The monitoring system specified in this report is capable of measuring (1) package position and orientation, (2) vault deformation, (3) brine accumulation, (4) spent fuel dissolution, (5) temperature, (6) nuclear radiation, and (7) package condition with sufficient accuracy to provide data input to a general risk assessment model. In order to define a monitoring system which can provide probabilistic data on radiological risk to operating personnel and the general public for a salt mine repository, the following information is required: (1) a complete design of the salt SURF repository including inventory, density and waste package design details; (2) probalistic failure rate data on containment integrity of the SURF waste package; (3) probabilistic failure rate data on the monitoring system components

Evaluation of repository safety

Energy Technology Data Exchange (ETDEWEB)

Sagar, B.; Patrick, W.; Dasgupta, B.; Mohanty, S. [Center for Nuclear Waste Regulatory Analyses, San Antonio (United States)

2002-07-01

The United States high-level waste program requires evaluation of radiological safety during two distinct time intervals. The first interval, commonly referred to as the preclosure period, deals with receipt of waste at the site, transfer into disposal containers, if needed, emplacement in the underground openings, monitoring and maintenance activities, backfill and closure of the underground openings, and decontamination and decommissioning of the surface facilities of the geologic repository. The preclosure period may extend from a few tens of years to as long as a few hundred of years, depending on repository design and societal norms regarding a final decision to permanently seal the repository. During the preclosure or operational period, performance confirmation studies are conducted to provide a basis for updating and reevaluating estimates of postclosure performance and, finally, to provide a basis for a closure decision. The postclosure period during which expected repository performance must meet certain standards may range from ten thousands years, as it does in the United States, to millions of years, as it does in some European nations. Waste handling operations in the preclosure period are to be evaluated in relation to their potential effect on workers, members of general public, and the general environment. During this period, releases of radioactivity are to be monitored and appropriate actions taken whenever established limits are approached or exceeded. Preclosure safety is highly dependent on facility design, operational hardware and automated systems, operational sequences, and reliability of humans involved in operations. Preclosure safety analyses conducted before operations begin play a major role in the design process, selection of equipment, and development of operational procedures. Because of the complexity, duration, and spatial scales of the operations, analyses are conducted using mathematical models implemented in computer codes

Evaluation of repository safety

International Nuclear Information System (INIS)

Sagar, B.; Patrick, W.; Dasgupta, B.; Mohanty, S.

2002-01-01

The United States high-level waste program requires evaluation of radiological safety during two distinct time intervals. The first interval, commonly referred to as the preclosure period, deals with receipt of waste at the site, transfer into disposal containers, if needed, emplacement in the underground openings, monitoring and maintenance activities, backfill and closure of the underground openings, and decontamination and decommissioning of the surface facilities of the geologic repository. The preclosure period may extend from a few tens of years to as long as a few hundred of years, depending on repository design and societal norms regarding a final decision to permanently seal the repository. During the preclosure or operational period, performance confirmation studies are conducted to provide a basis for updating and reevaluating estimates of postclosure performance and, finally, to provide a basis for a closure decision. The postclosure period during which expected repository performance must meet certain standards may range from ten thousands years, as it does in the United States, to millions of years, as it does in some European nations. Waste handling operations in the preclosure period are to be evaluated in relation to their potential effect on workers, members of general public, and the general environment. During this period, releases of radioactivity are to be monitored and appropriate actions taken whenever established limits are approached or exceeded. Preclosure safety is highly dependent on facility design, operational hardware and automated systems, operational sequences, and reliability of humans involved in operations. Preclosure safety analyses conducted before operations begin play a major role in the design process, selection of equipment, and development of operational procedures. Because of the complexity, duration, and spatial scales of the operations, analyses are conducted using mathematical models implemented in computer codes

Low- and intermediate-level waste repository-induced effects

Energy Technology Data Exchange (ETDEWEB)

Leupin, O.X.; Marschall, P.; Johnson, L.; Cloet, V.; Schneider, J. [National Cooperative for the Disposal of Radioactive Waste (NAGRA), Wettingen (Switzerland); Smith, P. [Safety Assessment Management Ltd, Henley-On-Thames, Oxfordshire (United Kingdom); Savage, D. [Savage Earth Associates Ltd, Bournemouth, Dorset (United Kingdom); Senger, R. [Intera Inc., Ennetbaden (Switzerland)

2016-10-15

This status report aims at describing and assessing the interactions of the radioactive waste emplaced in a low- and intermediate level waste (L/ILW) repository with the engineered materials and the Opalinus Clay host rock. The Opalinus Clay has a thickness of about 100 m in the proposed siting regions. Among other things the results are used to steer the RD and D programme of NAGRA. The repository-induced effects considered in this report are of the following broad types: - Thermal effects: i.e. effects arising principally from the heat generated by the waste and the setting of cement. - Rock-mechanical effects: i.e. effects arising from the mechanical disturbance to the rock caused by the excavation of the emplacement caverns and other underground structures. - Hydraulic and gas-related effects: i.e. the effects of repository resaturation and of gas generation, e.g. due to the corrosion of metals within the repository, on the host rock and engineered barriers. - Chemical effects: i.e. chemical interactions between the waste, the engineered materials and the host rock. Deep geological repositories are designed to avoid or mitigate the impact of potentially detrimental repository-induced effects on long-term safety. For the repository under consideration in the present report, an assessment of those repository-induced effects that remain shows that detrimental chemical and mechanical impacts are largely confined to the rock adjacent to the excavations, thermal impacts are minimal and gas effects can be mitigated by appropriate design measures to reduce gas production and provide pathways for gas transport that limit gas pressure build-up (engineered gas transport system, or EGTS). Specific measures that are part of the current reference design are discussed in relation to their significance with respect to repository-induced effects. The disposal system described in this report provides a system of passive barriers with multiple safety functions. The disposal

Low- and intermediate-level waste repository-induced effects

International Nuclear Information System (INIS)

Leupin, O.X.; Marschall, P.; Johnson, L.; Cloet, V.; Schneider, J.; Smith, P.; Savage, D.; Senger, R.

2016-10-01

This status report aims at describing and assessing the interactions of the radioactive waste emplaced in a low- and intermediate level waste (L/ILW) repository with the engineered materials and the Opalinus Clay host rock. The Opalinus Clay has a thickness of about 100 m in the proposed siting regions. Among other things the results are used to steer the RD and D programme of NAGRA. The repository-induced effects considered in this report are of the following broad types: - Thermal effects: i.e. effects arising principally from the heat generated by the waste and the setting of cement. - Rock-mechanical effects: i.e. effects arising from the mechanical disturbance to the rock caused by the excavation of the emplacement caverns and other underground structures. - Hydraulic and gas-related effects: i.e. the effects of repository resaturation and of gas generation, e.g. due to the corrosion of metals within the repository, on the host rock and engineered barriers. - Chemical effects: i.e. chemical interactions between the waste, the engineered materials and the host rock. Deep geological repositories are designed to avoid or mitigate the impact of potentially detrimental repository-induced effects on long-term safety. For the repository under consideration in the present report, an assessment of those repository-induced effects that remain shows that detrimental chemical and mechanical impacts are largely confined to the rock adjacent to the excavations, thermal impacts are minimal and gas effects can be mitigated by appropriate design measures to reduce gas production and provide pathways for gas transport that limit gas pressure build-up (engineered gas transport system, or EGTS). Specific measures that are part of the current reference design are discussed in relation to their significance with respect to repository-induced effects. The disposal system described in this report provides a system of passive barriers with multiple safety functions. The disposal

Repository surface design site layout analysis

International Nuclear Information System (INIS)

Montalvo, H.R.

1998-01-01

The purpose of this analysis is to establish the arrangement of the Yucca Mountain Repository surface facilities and features near the North Portal. The analysis updates and expands the North Portal area site layout concept presented in the ACD, including changes to reflect the resizing of the Waste Handling Building (WHB), Waste Treatment Building (WTB), Carrier Preparation Building (CPB), and site parking areas; the addition of the Carrier Washdown Buildings (CWBs); the elimination of the Cask Maintenance Facility (CMF); and the development of a concept for site grading and flood control. The analysis also establishes the layout of the surface features (e.g., roads and utilities) that connect all the repository surface areas (North Portal Operations Area, South Portal Development Operations Area, Emplacement Shaft Surface Operations Area, and Development Shaft Surface Operations Area) and locates an area for a potential lag storage facility. Details of South Portal and shaft layouts will be covered in separate design analyses. The objective of this analysis is to provide a suitable level of design for the Viability Assessment (VA). The analysis was revised to incorporate additional material developed since the issuance of Revision 01. This material includes safeguards and security input, utility system input (size and location of fire water tanks and pump houses, potable water and sanitary sewage rates, size of wastewater evaporation pond, size and location of the utility building, size of the bulk fuel storage tank, and size and location of other exterior process equipment), main electrical substation information, redundancy of water supply and storage for the fire support system, and additional information on the storm water retention pond

EBS modelling for the development of repository concepts tailored to siting environments

International Nuclear Information System (INIS)

Ishiguro, K.; Ueda, H.; Wakasugi, K.; Sakabe, Y.; Kitayama, K.; Umeki, H.; Takase, H.

2007-01-01

The Japanese siting approach for a HLW repository calls for volunteer host municipalities and thereby places particular emphasis on design flexibility. In particular, the repository concept needs to be tailored to the specific site characteristics. Starting from the H12 repository concept, NUMO has been examining a range of possible repository design options, including the EBS. In this paper. the requirements and strategy for the development of models for performance assessment and process understanding are discussed, taking into account the step-wise, iterative process of developing repository concepts. The areas requiring further development of models and databases in the long-term R and D programme have been identified as a 'wish list' that relates to the evaluation of a range of potential repository concepts, focusing on the near-field for the early stages of the development process. Among the issues on the list, NUMO has started the development of a flexible computer code for modelling three-dimensional mass transport to evaluate the impacts of various design options and components of the EBS. This tool has been applied to the analysis of the barrier effects of the tunnel plugs located in fractured rock. (authors)

THERMAL CONDUCTIVITY OF NON-REPOSITORY LITHOSTRATIGRAPHIC LAYERS

International Nuclear Information System (INIS)

R. JONES

2004-01-01

This model report addresses activities described in ''Technical Work Plan for: Near-Field Environment and Transport Thermal Properties and Analysis Reports Integration'' (BSC 2004 [DIRS 171708]). The model develops values for thermal conductivity, and its uncertainty, for the nonrepository layers of Yucca Mountain; in addition, the model provides estimates for matrix porosity and dry bulk density for the nonrepository layers. The studied lithostratigraphic units, as identified in the ''Geologic Framework Model'' (GFM 2000) (BSC 2004 [DIRS 170029]), are the Timber Mountain Group, the Tiva Canyon Tuff, the Yucca Mountain Tuff, the Pah Canyon Tuff, the Topopah Spring Tuff (excluding the repository layers), the Calico Hills Formation, the Prow Pass Tuff, the Bullfrog Tuff, and the Tram Tuff. The deepest model units of the GFM (Tund and Paleozoic) are excluded from this study because no data suitable for model input are available. The parameter estimates developed in this report are used as input to various models and calculations that simulate heat transport through the rock mass. Specifically, analysis model reports that use product output from this report are: (1) Drift-scale coupled processes (DST and TH seepage) models; (2) Drift degradation analysis; (3) Multiscale thermohydrologic model; and (4) Ventilation model and analysis report. In keeping with the methodology of the thermal conductivity model for the repository layers in ''Thermal Conductivity of the Potential Repository Horizon'' (BSC 2004 [DIRS 169854]), the Hsu and others (1995 [DIRS 158073]) three-dimensional (3-D) cubic model (referred to herein as ''the Hsu model'') was used to represent the matrix thermal conductivity as a function of the four parameters (matrix porosity, thermal conductivity of the saturating fluid, thermal conductivity of the solid, and geometric connectivity of the solid). The Hsu model requires input data from each test specimen to meet three specific conditions: (1) Known value

Industrial complementarities between interim storage and reversible geological repository - 59237

International Nuclear Information System (INIS)

Hoorelbeke, Jean-Michel

2012-01-01

The French Act voted in 2006 made the choice of deep geological disposal as the reference option for the long term management of high level (HLW) and intermediate level long-lived waste. The CIGEO repository project aims at avoiding or limiting burden to future generations, which could not be achieved by the extension in time of interim storage. The reversibility as provided by the Act will maintain a liberty of choice for waste management on a duration which is comparable to new storage facility. Interim storage is required to accommodate waste as long as the repository is not available. The commissioning of the repository in 2025 will not suppress needs for interim storage. The paper describes the complementarities between existing and future interim storage facilities and the repository project: repository operational issues and planning, HLW thermal decay, support for the reversibility, etc. It shows opportunities to prepare a global optimization of waste management including the utilization at best of storage capacities and the planning of waste emplacement in the repository in such a way to facilitate operational conditions and to limit cost. Preliminary simulations of storage-disposal scenarios are presented. Thanks to an optimal use of the waste management system, provision can be made for a progressive increase of waste emplacement flow during the first operation phase of the repository. It is then possible to stabilize the industrial activity level of the repository site. An optimal utilization of interim storage can also limit the diversity of waste packages emplaced simultaneously, which facilitates the operation of the repository. 60 years minimum interim storage duration is generally required with respect to HLW thermal output. Extending this interim storage period may reduce the underground footprint of the repository. Regarding reversibility, the capability to manage waste packages potentially retrieved from the repository should be analyzed. The

Report of the Task Force on the MRS/repository interface

International Nuclear Information System (INIS)

1986-02-01

In April 1985, the DOE established an MRS/repository interface task force to analyze the cost and schedule impacts of implementing an integrated waste-management system on the repository and the MRS facility. The intended end products of the study were preliminary conceptual designs of repository and MRS facilities, cost and schedule estimates, and other analyses that would advance the definition of the role and function of the MRS facility, support the preparation of the MRS proposal to Congress, and serve as a source of baseline data for further studies of the integrated waste-management system. From the general overall objectives, specific equations were developed to guide the task-force effort, e.g., What would the surface facilities at the repository look like and cost with an MRS facility in the system. In order to address these questions, five scenarios were defined and analyzed. (A number of other scenarios and associated issues were also explored to a lesser extent.) These five scenarios are as follows. Scenario 1: reference case (no MRS facility). Scenario 2: MRS facility with overpacking of both spent fuel and defense high-level waste. Scenario 3: MRS facility with overpacking of spent fuel only (defense-waste overpacking at the repository). Scenario 4: MRS facility with all overpacking at the repository. Scenario 5: MRS facility with all overpacking at the repository and western fuel shipped directly to the repository. It is apparent that, with such a limited set of scenarios, determination of the optimum system was not an objective of this study. Furthermore, time constraints limited the level of detail to which facility designs could be developed; this level can best be characterized as ''preconceptual.'' These limitations are, however, compatible with the intent of the study, which was to make general comparisons between the several systems on an internally consistent basis

Asse salt mine nuclear waste repository simulation experiments

International Nuclear Information System (INIS)

Coyle, A.J.

1983-01-01

The field tests underway in Asse, Federal Republic of Germany are dicected toward the development of test plans, techniques and equipment to be used in Exploratory Shafts or At Depth Test Facilities confirmation tests. These simulated repository tests will also provide information which address the following issues: brine migration (liquid and vapor); radiation effects of gamma rays; gas generation caused by radiation and corrosion; accelerated corrosion and leaching; altered properties of salt (the effects of heat, radiation and brine); and the effects of heat and radiation on test assemblies, instruments, and various materials exposed to repository conditions. This paper is a status of the first 82 days of operation of the Asse Brine Migration Tests, which were initiated on May 25, 1983. 6 references

People's perception of LILW repository

International Nuclear Information System (INIS)

Zeleznik, Nadja; Polic, Marko

2002-01-01

Full text: Social acceptability of the radioactive waste repository presents a great problem in every country with such a waste. Even if people agree with the need for its construction, the chosen location should be far from their homes (NIMBY). The reasons for such attitudes were attributed to different causes: uneducated public, differences in understanding of radioactivity and risk by experts and lay public, risk communication problems, lack of credibility and social trust, etc. While in earlier days public was blamed for its irrationality, and need for education and information was emphasized, today it is realized that public trust is extremely important if effective risk communication is to be achieved. It is also recognized that it is not so much the content of the risk message itself, as the lack of trust to those responsible for provision of information that is behind this opposition. Perhaps we could apply here Petty and Caciopo's elaboration likelihood model of persuasion, with credibility as a factor in peripheral route of persuasion. Nevertheless also general lowering of social trust should explain social non-agreement. This lack of trust in experts and political institutions is perhaps caused by outwitting public in earlier years, its bad experiences with responsible officials, dangerous accidents (e.g. TMI, Chernobyl), increased influence that professions have over people's welfare, a greater value placed on equality and better educated public, etc. In 1996 the ARAO re-initiated the search for a LILW repository location with a new, so-called combined approach to the site selection, where the technical, geologically led process is combined with participation of local community. In order to get information on people's perception of the LILW repository construction, their willingness to accept it and factors that influence the acceptability, several surveys have been conducted. Groups of experts and lay persons answered the questionnaires. The results of

Czech Republic. Dukovany repository

International Nuclear Information System (INIS)

2001-01-01

Full text: The repository at the Dukovany site is a structure located above the land surface. It consists of two double-rows of reinforced concrete vaults. Each double-row has dimensions 38x160x6 meters and contains 2x28 vaults. The internal dimensions of each vault are 18x6x5.4 meters. The repository serves for reactor wastes from the Dukovany and Temelin nuclear power plants (NPPs). Its capacity is 55,000 m 3 or 130,000 drums. The repository is a fully engineered facility with multiple barriers. The first engineered barrier is the waste form (in the case of waste from the Dukovany NPP, the waste form is mainly bitumen, but concrete and glass are also considered as suitable solidification products). The second barrier is the container (a 200 litre steel drum or a HIC container), whereas the third consists of cut-off reinforced concrete walls with asphalt-based hydro-insulation. The fourth barrier is a cap which should protect the vaults against infiltration of rainwater and should serve also as an intrusion and erosion barrier. The fifth barrier is a drainage system around the repository which is composed of layers of gravel and sand. The void space in drums around the waste is filled with specially composed grout. Such waste packages are emplaced into the disposal vault, which is covered by pre-fabricated panels. Thereafter, joints between the panels are sealed and a provisional coverage added; the final cover, however, will be constructed only over the whole row of 28 vaults, until all vaults are filled with waste. The final cover will encompass the following components: reinforced concrete pre-fabricated panels (500 mm); cement overcoat (30 mm); insulation foil; concrete layer for cap levelling (5-150 mm); layer of asphalto-propylene concrete (150 mm); soil (450 mm); geotextile foil with topsoil (top surface vegetation). (author)

Repository sealing concepts for the Nevada nuclear waste storage Investigations Project

International Nuclear Information System (INIS)

Fernandez, J.A.; Freshley, M.D.

1984-08-01

This report describes concepts for sealing a nuclear waste repository in an unsaturated tuff environment. The repository site under consideration is Yucca Mountain, which is on and adjacent to the Nevada Test Site. The hydrogeology of Yucca Mountain, preliminary repository concepts, functional requirements and performance criteria for sealing, federal and state regulations, and hydrological calculations are considered in developing the sealing concepts. Water flow through the unsaturated zone is expected to be small and generally vertically downward with some potential to occur through discrete fault and fracture zones. These assumptions are used in developing sealing concepts for shafts, ramps, and boreholes. Sealing of discrete, water-producing faults and fracture zones encountered in horizontal emplacement holes and in access and emplacement drifts is also described. 49 references, 21 figures, 6 tables

Geological criteria for site selection of an LILW radioactive waste repository in the Philippines

International Nuclear Information System (INIS)

Aurelio, Mario; Taguibao, Kristine Joy; Vargas, Edmundo; Palattao, Maria Visitacion; Reyes, Rolando; Nohay, Carl; Singayan, Alfonso

2013-01-01

In the selection of sites for disposal facilities involving low- and intermediate-level radioactive waste (LILW), International Atomic Energy Agency (IAEA) recommendations require that 'the region in which the site is located shall be such that significant tectonic and surface processes are not expected to occur with an intensity that would compromise the required isolation capability of the repository'. Evaluating the appropriateness of a site therefore requires a deep understanding of the geological and tectonic setting of the area. The Philippines sits in a tectonically active region frequented by earthquakes and volcanic activity. Its highly variable morphology coupled with its location along the typhoon corridor in the west Pacific region subjects the country to surface processes often manifested in the form of landslides. The Philippine LILW near surface repository project site is located on the north eastern sector of the Island of Luzon in northern Philippines. This island is surrounded by active subduction trenches; to the east by the East Luzon Trough and to the west by the Manila Trench. The island is also traversed by several branches of the Philippine Fault System. The Philippine LILW repository project is located more than 100 km away from any of these major active fault systems. In the near field, the project site is located less than 10 km from a minor fault (Dummon River Fault) and more than 40 km away from a volcanic edifice (Mt. Caguas). This paper presents an analysis of the potential hazards that these active tectonic features may pose to the project site. The assessment of such geologic hazards is imperative in the characterization of the site and a crucial input in the design and safety assessment of the repository. (authors)

Geological criteria for site selection of an LILW radioactive waste repository in the Philippines

Energy Technology Data Exchange (ETDEWEB)

Aurelio, Mario; Taguibao, Kristine Joy [National Institute of Geological Sciences, University of the Philippines, Quezon City (Philippines); Vargas, Edmundo; Palattao, Maria Visitacion; Reyes, Rolando; Nohay, Carl; Singayan, Alfonso [Philippine Nuclear Research Institute, Department of Science and Technology, Quezon City (Philippines)

2013-07-01

In the selection of sites for disposal facilities involving low- and intermediate-level radioactive waste (LILW), International Atomic Energy Agency (IAEA) recommendations require that 'the region in which the site is located shall be such that significant tectonic and surface processes are not expected to occur with an intensity that would compromise the required isolation capability of the repository'. Evaluating the appropriateness of a site therefore requires a deep understanding of the geological and tectonic setting of the area. The Philippines sits in a tectonically active region frequented by earthquakes and volcanic activity. Its highly variable morphology coupled with its location along the typhoon corridor in the west Pacific region subjects the country to surface processes often manifested in the form of landslides. The Philippine LILW near surface repository project site is located on the north eastern sector of the Island of Luzon in northern Philippines. This island is surrounded by active subduction trenches; to the east by the East Luzon Trough and to the west by the Manila Trench. The island is also traversed by several branches of the Philippine Fault System. The Philippine LILW repository project is located more than 100 km away from any of these major active fault systems. In the near field, the project site is located less than 10 km from a minor fault (Dummon River Fault) and more than 40 km away from a volcanic edifice (Mt. Caguas). This paper presents an analysis of the potential hazards that these active tectonic features may pose to the project site. The assessment of such geologic hazards is imperative in the characterization of the site and a crucial input in the design and safety assessment of the repository. (authors)

Implementation of an OAIS Repository Using Free, Open Source Software

Science.gov (United States)

Flathers, E.; Gessler, P. E.; Seamon, E.

2015-12-01

The Northwest Knowledge Network (NKN) is a regional data repository located at the University of Idaho that focuses on the collection, curation, and distribution of research data. To support our home institution and others in the region, we offer services to researchers at all stages of the data lifecycle—from grant application and data management planning to data distribution and archive. In this role, we recognize the need to work closely with other data management efforts at partner institutions and agencies, as well as with larger aggregation efforts such as our state geospatial data clearinghouses, data.gov, DataONE, and others. In the past, one of our challenges with monolithic, prepackaged data management solutions is that customization can be difficult to implement and maintain, especially as new versions of the software are released that are incompatible with our local codebase. Our solution is to break the monolith up into its constituent parts, which offers us several advantages. First, any customizations that we make are likely to fall into areas that can be accessed through Application Program Interfaces (API) that are likely to remain stable over time, so our code stays compatible. Second, as components become obsolete or insufficient to meet new demands that arise, we can replace the individual components with minimal effect on the rest of the infrastructure, causing less disruption to operations. Other advantages include increased system reliability, staggered rollout of new features, enhanced compatibility with legacy systems, reduced dependence on a single software company as a point of failure, and the separation of development into manageable tasks. In this presentation, we describe our application of the Service Oriented Architecture (SOA) design paradigm to assemble a data repository that conforms to the Open Archival Information System (OAIS) Reference Model primarily using a collection of free and open-source software. We detail the design

Towards Interoperable Preservation Repositories: TIPR

Directory of Open Access Journals (Sweden)

Priscilla Caplan

2010-07-01

Full Text Available Towards Interoperable Preservation Repositories (TIPR is a project funded by the Institute of Museum and Library Services to create and test a Repository eXchange Package (RXP. The package will make it possible to transfer complex digital objects between dissimilar preservation repositories.  For reasons of redundancy, succession planning and software migration, repositories must be able to exchange copies of archival information packages with each other. Every different repository application, however, describes and structures its archival packages differently. Therefore each system produces dissemination packages that are rarely understandable or usable as submission packages by other repositories. The RXP is an answer to that mismatch. Other solutions for transferring packages between repositories focus either on transfers between repositories of the same type, such as DSpace-to-DSpace transfers, or on processes that rely on central translation services.  Rather than build translators between many dissimilar repository types, the TIPR project has defined a standards-based package of metadata files that can act as an intermediary information package, the RXP, a lingua franca all repositories can read and write.

Repository simulation model: Final report

International Nuclear Information System (INIS)

1988-03-01

This report documents the application of computer simulation for the design analysis of the nuclear waste repository's waste handling and packaging operations. The Salt Repository Simulation Model was used to evaluate design alternatives during the conceptual design phase of the Salt Repository Project. Code development and verification was performed by the Office of Nuclear Waste Isolation (ONWL). The focus of this report is to relate the experience gained during the development and application of the Salt Repository Simulation Model to future repository design phases. Design of the repository's waste handling and packaging systems will require sophisticated analysis tools to evaluate complex operational and logistical design alternatives. Selection of these design alternatives in the Advanced Conceptual Design (ACD) and License Application Design (LAD) phases must be supported by analysis to demonstrate that the repository design will cost effectively meet DOE's mandated emplacement schedule and that uncertainties in the performance of the repository's systems have been objectively evaluated. Computer simulation of repository operations will provide future repository designers with data and insights that no other analytical form of analysis can provide. 6 refs., 10 figs

Disruption scenarios for a high-level waste repository at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Ross, B.

1986-01-01

A high-level waste repository located in unsaturated welded tuff at Yucca Mountain, Nevada, would rely on six different, although not entirely independent, barriers to prevent escape of radioactivity. These barriers are the waste canister, fuel cladding, slow dissolution of the spent fuel itself, and slow movement of released contaminants in three different hydrogeologic units: the unsaturated Topopah Spring welded tuff unit, the unsaturated Calico Hills nonwelded tuff unit, and the saturated tuff aquifer. Fifty-eight processes and events that might affect such a repository were reviewed. Eighty-three different sequences were identified by which these processes and events could lead to failure of one or more barriers. Sequences which had similar consequences were grouped, yielding 17 categories. The repository system has considerable redundancy; most of the more likely disruptions affect only one or a few barriers. Occurrence of more than one disruption is needed before such disruptions would cause release of radioactivity. Future studies of repository performance must assess the likelihood and consequences of multiple-disruption scenarios to evaluate how well the repository meets performance standards

Deep geological isolation of nuclear waste: numerical modeling of repository scale hydrology

International Nuclear Information System (INIS)

Dettinger, M.D.

1980-04-01

The Scope of Work undertaken covers three main tasks, described as follows: (Task 1) CDM provided consulting services to the University on modeling aspects of the study having to do with transport processes involving the local groundwater system near the repository and the flow of fluids and vapors through the various porous media making up the repository system. (Task 2) CDM reviewed literature related to repository design, concentrating on effects of the repository geometry, location and other design factors on the flow of fluids within the repository boundaries, drainage from the repository structure, and the eventual transport of radionucldies away from the repository site. (Task 3) CDM, in a joint effort with LLL personnel, identified generic boundary and initial conditions, identified processes to be modeled, and recommended a modeling approach with suggestions for appropriate simplifications and approximations to the problem and identifiying important parameters necessary to model the processes. This report consists of two chapters and an appendix. The first chapter (Chapter III of the LLL report) presents a detailed description and discussion of the modeling approach developed in this project, its merits and weaknesses, and a brief review of the difficulties anticipated in implementing the approach. The second chapter (Chapter IV of the LLL report) presents a summary of a survey of researchers in the field of repository performance analysis and a discussion of that survey in light of the proposed modeling approach. The appendix is a review of the important physical processes involved in the potential hydrologic transport of radionuclides through, around and away from deep geologic nuclear waste repositories

Commercial nuclear waste repository in basalt

International Nuclear Information System (INIS)

Hardy, M.P.; Patricio, J.G.; Heley, W.H.

1980-06-01

The Basalt Waste Isolation Project (BWIP) is an ongoing research and engineering effort being conducted by Rockwell Hanford Operations (Rockwell), which is under contract to the US Department of Energy. The objectives of this program are to assess the feasibility of and to provide the technology needed to design and construct a licensed commercial nuclear waste repository in the deep basalt formations underlying the Hanford Site. An extensive preconceptual design effort was undertaken during 1979 to develop a feasible concept that could serve as a reference design for both surface and underground facilities. The preconceptual design utilized existing technology to the greatest extent possible to offer a system design that could be utilized in establishing schedule and cost baseline data, recommend alternatives that require additional study, and develop basic design requirements that would allow evolution of the design process prior to the existence of legislated criteria. This paper provides a description of the concept developed for the subsurface aspects of this nuclear waste repository

LIFE Materials: Fuel Cycle and Repository Volume 11

Energy Technology Data Exchange (ETDEWEB)

Shaw, H; Blink, J A

2008-12-12

to meet the thermal constraints of the repository design. (4) A simple, but arguably conservative, estimate for the dose from a repository containing 63,000 MT of spent LIFE fuel would have similar performance to the currently planned Yucca Mountain Repository. This indicates that a properly designed 'LIFE Repository' would almost certainly meet the proposed Nuclear Regulatory Commission standards for dose to individuals, even though the waste in such a repository would have produced 20-30 times more generated electricity than the reference case for Yucca Mountain. The societal risk/benefit ratio for a LIFE repository would therefore be significantly better than for currently planned repositories for LWR fuel.

LIFE Materials: Fuel Cycle and Repository Volume 11

International Nuclear Information System (INIS)

Shaw, H.; Blink, J.A.

2008-01-01

the repository design. (4) A simple, but arguably conservative, estimate for the dose from a repository containing 63,000 MT of spent LIFE fuel would have similar performance to the currently planned Yucca Mountain Repository. This indicates that a properly designed 'LIFE Repository' would almost certainly meet the proposed Nuclear Regulatory Commission standards for dose to individuals, even though the waste in such a repository would have produced 20-30 times more generated electricity than the reference case for Yucca Mountain. The societal risk/benefit ratio for a LIFE repository would therefore be significantly better than for currently planned repositories for LWR fuel

Biosphere modelling for the assessment of radioactive waste repositories: the development of a common basis by the BIOMOVS II working group on reference biospheres

International Nuclear Information System (INIS)

VanDorp, F.

1996-01-01

Performance criteria for radioactive waste repositories are often expressed in terms of dose or risk. The characteristics of biosphere modelling for performance assessment are that: a) potential release occurs in the distant future, b) reliable predictions of human behaviour at the time of release are impracticable, and c) the biosphere is not considered to be a barrier. For these and other reasons, many unexplained differences have arisen in the approaches to biosphere modelling. The BIOMOVS II Working Group on Reference Biospheres has developed a) a recommended methodology for biosphere model development, b) a structured electronic list of features, events and processes (FEPs), and c) an illustrative example of the recommended methodology. The Working Group has successfully tested the Interaction Matrix (or Rock Engineering Systems, RES) approach for developing conceptual models. The BIOMOVS II Working Groups on Reference Biospheres and Complementary Studies have achieved considerable harmonisation in approaches to biosphere modelling. (author)

Geohydrological simulation of a deep coastal repository

International Nuclear Information System (INIS)

Follin, S.

1995-12-01

This conceptual-numerical study treats the dewatering and resaturation phases associated with the construction, use and closure of a coastal nuclear waste repository located at depth in sparsely fractured Baltic Shield rocks. The main objective is to simulate the extent and duration of saline intrusion for a reasonable set of geohydrological assumptions. Long-term changes in the chemical environment associated with saline intrusion may affect the properties of the buffer zone material (bentonite). The first part of the study deals with history matching of a simple model geometry and the second part treats the dewatering and resaturation phases of the simulated repository. The history matching supports the standpoint that the occurrence of saline ground water reflects an ongoing but incomplete Holocene flushing of the Baltic Shield. The drawdown after fifty years of dewatering is highly dependent on the permeability of the excavated damaged zone. If the permeability close the repository is unaltered the entire region between the top side of the model and the repository is more or less partially saturated at the end of the simulation period. The simulations of a fifty year long recovery period suggest that the distribution between fresh and saline ground waters may be quite close to the conditions prior to the dewatering phase already after fifty years of closure despite an incomplete pressure recovery, which is an interesting result considering the objective of the study. 12 refs

Final repository for spent nuclear fuel. Underground design Forsmark, Layout D1

International Nuclear Information System (INIS)

Brantberger, Martin; Zetterqvist, Anders; Arnbjerg-Nielsen, Torben; Olsson, Tommy; Outters, Nils; Syrjaenen, Pauli

2006-04-01

This report comprises the design step D1 related to the underground design for a deep repository located at the Forsmark site. The design is based on the Site Descriptive Model Forsmark v1.2. All studies have been focussed at an area southeast of the Forsmark nuclear plant, which has been considered to be the most promising area for hosting the repository. SKB has developed guidelines for the design of the repository, which further describes the methodology applied for the studies. From these guidelines the following basic objectives for the design step D1 are summarized: to determine whether the final repository can be accommodated within the studied site; to identify site-specific facility critical issues; to test and evaluate the design methodology; to provide feedback to: the design organisation regarding additional studies that needs to be done; the site investigation and modelling organization regarding further investigations required; and the safety assessment team. The possible locations for a tentative deep repository are analysed in Chapter 3 of the report. The most promising area for the repository (denoted 'priority site') has been defined by SKB to be located southeast of the Forsmark nuclear plant and northwest of the gently dipping deformation zone ZFMNE00A2. Regarding the repository depth, present knowledge acquired from the site investigations indicates that it is possible to locate the repository at all stipulated depths according to SKB, that is between 400 m and 700 m depth. The preliminary assessment made in Chapter 3 clearly demonstrates that the repository can be accommodated within the 'priority site'. The potential to accommodate the repository is essentially the same for both 400 m and 500 m depths. The design of the deposition areas is reported in Chapter 4, which includes the design of layout features for all tunnels and deposition holes, orientation of tunnels, calculation of anticipated loss of deposition holes due to the applied

Final repository for spent nuclear fuel. Underground design Forsmark, Layout D1

Energy Technology Data Exchange (ETDEWEB)

Brantberger, Martin; Zetterqvist, Anders [Ramboell Sweden AB, Stockholm (Sweden); Arnbjerg-Nielsen, Torben [Ramboell Denmark A/S, Virum (Denmark); Olsson, Tommy [IandT Olsson AB, Uppsala (Sweden); Outters, Nils [Golder Associates AB, Uppsala (Sweden); Syrjaenen, Pauli [Gridpoint Oy, Helsinki (Sweden)

2006-04-15

This report comprises the design step D1 related to the underground design for a deep repository located at the Forsmark site. The design is based on the Site Descriptive Model Forsmark v1.2. All studies have been focussed at an area southeast of the Forsmark nuclear plant, which has been considered to be the most promising area for hosting the repository. SKB has developed guidelines for the design of the repository, which further describes the methodology applied for the studies. From these guidelines the following basic objectives for the design step D1 are summarized: to determine whether the final repository can be accommodated within the studied site; to identify site-specific facility critical issues; to test and evaluate the design methodology; to provide feedback to: the design organisation regarding additional studies that needs to be done; the site investigation and modelling organization regarding further investigations required; and the safety assessment team. The possible locations for a tentative deep repository are analysed in Chapter 3 of the report. The most promising area for the repository (denoted 'priority site') has been defined by SKB to be located southeast of the Forsmark nuclear plant and northwest of the gently dipping deformation zone ZFMNE00A2. Regarding the repository depth, present knowledge acquired from the site investigations indicates that it is possible to locate the repository at all stipulated depths according to SKB, that is between 400 m and 700 m depth. The preliminary assessment made in Chapter 3 clearly demonstrates that the repository can be accommodated within the 'priority site'. The potential to accommodate the repository is essentially the same for both 400 m and 500 m depths. The design of the deposition areas is reported in Chapter 4, which includes the design of layout features for all tunnels and deposition holes, orientation of tunnels, calculation of anticipated loss of deposition holes due

Public acceptance for centralized storage and repositories of low-level waste session (Panel)

Energy Technology Data Exchange (ETDEWEB)

Lutz, H.R.

1995-12-31

Participants from various parts of the world will provide a summary of their particular country`s approach to low-level waste management and the cost of public acceptance for low-level waste management facilities. Participants will discuss the number, geographic location, and type of low-level waste repositories and centralized storage facilities located in their countries. Each will discuss the amount, distribution, and duration of funds to gain public acceptance of these facilities. Participants will provide an estimated $/meter for centralized storage facilities and repositories. The panel will include a brief discussion about the ethical aspects of public acceptance costs, approaches for negotiating acceptance, and lessons learned in each country. The audience is invited to participate in the discussion.

Repositories; Repositorios

Energy Technology Data Exchange (ETDEWEB)

Freire, Carolina Braccini; Tello, Cledola Cassia Oliveira de [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)]. E-mails: cbf@cdtn.br; tellocc@cdtn.br

2007-11-15

The use of the nuclear energy is increasing in all areas. Then the radioactive waste management is in continuous development to comply the national and international established requirements. The final objective is to assure that it will not have any contamination of the public or the environmental, and that the exposition doses will be lower than the radiological protection limits. The multi barrier concept for the repository is internationally recognized. Among the repository types, the most used are: near surface, geological formations and of deposition in rock cavities. This article explains the concept and the types of repository and gives some examples of them. (author)

Geoscience data base handbook for modeling a nuclear waste repository. Volume 1

International Nuclear Information System (INIS)

Isherwood, D.

1979-12-01

This handbook contains reference information on parameters that should be considered in analyzing or modeling a proposed nuclear waste repository site. Only those parameters and values that best represent the natural environment are included. Rare extremes are avoided. Where laboratory and field data are inadequate, theoretical treatments and informed engineering judgements are presented. Volume 1 contains a data base on salt as a repository medium. Chapters on the geology of bedded and dome salt, the geomechanics of salt, hydrology, geochemistry, natural and man-made features, and seismology provide compiled data and related information useful for studying a proposed repository in salt. These and other data will be needed to derive generic deep geologic modeling parameters and will also serve as background for the verification of source data that may be presented in licensing applications for nuclear waste repositories. Volume 2 is the result of a scoping study for a data base on the geology, geomechanics, and hydrology of shale, granite, and basalt as alternative repository media. Except for the geomechanics of shale, most of the sections contain relatively complete compilations of the available data, as well as discussions of the properties that are unique to each rock type

Thermal Conductivity of the Potential Repository Horizon Model Report

International Nuclear Information System (INIS)

Ramsey, J.

2002-01-01

The purpose of this report is to assess the spatial variability and uncertainty of thermal conductivity in the host horizon for the proposed repository at Yucca Mountain. More specifically, the lithostratigraphic units studied are located within the Topopah Spring Tuff (Tpt) and consist of the upper lithophysal zone (Tptpul), the middle nonlithophysal zone (Tptpmn), the lower lithophysal zone (Tptpll), and the lower nonlithophysal zone (Tptpln). The Tptpul is the layer directly above the repository host layers, which consist of the Tptpmn, Tptpll, and the Tptpln. Current design plans indicate that the largest portion of the repository will be excavated in the Tptpll (Board et al. 2002 [157756]). The main distinguishing characteristic among the lithophysal and nonlithophysal units is the percentage of large scale (cm-m) voids within the rock. The Tptpul and Tptpll, as their names suggest, have a higher percentage of lithophysae than the Tptpmn and the Tptpln. Understanding the influence of the lithophysae is of great importance to understanding bulk thermal conductivity and perhaps repository system performance as well. To assess the spatial variability and uncertainty of thermal conductivity, a model is proposed that is functionally dependent on the volume fraction of lithophysae and the thermal conductivity of the matrix portion of the rock. In this model, void space characterized as lithophysae is assumed to be air-saturated under all conditions, while void space characterized as matrix may be either water- or air-saturated. Lithophysae are assumed to be air-saturated under all conditions since the units being studied are all located above the water table in the region of interest, and the relatively strong capillary forces of the matrix will, under most conditions, preferentially retain any moisture present in the rock

Development of geological disposal system; localization of element cost data and cost evaluation on the HLW repository

Energy Technology Data Exchange (ETDEWEB)

Lee, Byung Sik; Kim, Kil Jung; Yang, Young Jin; Kim, Sung Chun [KOPEC, Taejeon (Korea)

2002-03-01

To estimate Total Life Cycle Cost (TSLCC) for Korea HLW Repository through localization of element cost data, we review and re-organize each basic element cost data for reference repository system, localize various element cost and finally estimate TSLCC considering economic parameters. As results of the study, TSLCC is estimated as 17,167,689 million won, which includes costs for site preparation, surface facilities, underground facilities and management/integration. Since HLW repository Project is an early stage of pre-conceptual design at present, the information of design and project information are not enough to perform cost estimate and cost localization for the Project. However, project cost structure is re-organized based on the local condition and Total System Life Cycle Cost is estimated using the previous cost data gathered from construction experience of the local nuclear power plant. Project results can be used as basic reference data to assume total construction cost for the local HLW repository and should be revised to more reliable cost data with incorporating detail project design information into the cost estimate in a future. 20 refs. (Author)

Workshops for state review of site suitability criteria for high-level radioactive waste repositories: analysis and recommendations

International Nuclear Information System (INIS)

1978-02-01

The purpose of this report is to present the views and recommendations of invited State officials and legislators participating in a workshop concerned with preliminary site suitability criteria for high level radioactive waste repositories. The workshops were open to the public and were conducted by the U. S. Nuclear Regulatory Commission (NRC) during September 1977 in three regional locations across the United States. This contractor report is the second of two reports and consolidates the discussion by State officials on the role of a State in siting a repository, NRC's waste management program, the transportation of high level wastes, the number and location of repositories and concerns with the socio-economic impacts of siting a repository in a community. The recommendations to the NRC can be categorized into four areas. These were: (1) general recommendations, (2) procedural recommendations, (3) recommendations for improving communications, and (4) specific recommendations on the preliminary siting criteria. The recommendations emphasized the need for early State involvement in the siting process, the need for an impacted State to assess repository operations, the need for early solution of waste transportation concerns, and the requirement that any repository developed insure the protection of the public health and safety as its most important characteristic. Other participant recommendations are included in the body of the report

Logistics characterization for regional spent fuel repositories concept

International Nuclear Information System (INIS)

Joy, D.S.; Hudson, B.J.; Anthony, M.W.

1980-08-01

This report summarizes a study of logistics considerations for a four-region repository system for spent fuel disposal. The logistics considerations include: (1) yearly receipt and emplacement; (2) inventory; (3) away-from-reactor (AFR) storage; (4) nuclear capacity growth effects; (5) entire lifetime of reactors served by repository operations; (6) proportions of pressurized-water-reactor (PWR)/boiling-water-reactor (BWR) fuel; (7) proportions of rail and truck shipments; (8) shipping cask fleet requirements; (9) number of annual shipments; (10) mode (rail/truck) and cost of shipment; and (11) initial year for shipment to maintain full core reserve. The nation was divided into Northeast, North Central, Southern, and Western regions for evaluation purposes. Repository logistics were analyzed in each region based on three different capacity projections. For the Southern region, results for seven salt dome sites are presented. The Western region results cover four potential sites. The North Central and Northeastern regions results are not presented on a site specific basis. Conclusions are drawn based on the results. The methodology assumptions and references used in the logistics analysis are described for the convenience of the reader

Workshop on development of radionuclide getters for the Yucca Mountain waste repository: proceedings.

Energy Technology Data Exchange (ETDEWEB)

Moore, Robert Charles; Lukens, Wayne W. (Lawrence Berkeley National Laboratory)

2006-03-01

The proposed Yucca Mountain repository, located in southern Nevada, is to be the first facility for permanent disposal of spent reactor fuel and high-level radioactive waste in the United States. Total Systems Performance Assessment (TSPA) analysis has indicated that among the major radionuclides contributing to dose are technetium, iodine, and neptunium, all of which are highly mobile in the environment. Containment of these radionuclides within the repository is a priority for the Yucca Mountain Project (YMP). These proceedings review current research and technology efforts for sequestration of the radionuclides with a focus on technetium, iodine, and neptunium. This workshop also covered issues concerning the Yucca Mountain environment and getter characteristics required for potential placement into the repository.

Staff Technical Position on consideration of fault displacement hazards in geologic repository design

International Nuclear Information System (INIS)

McConnell, K.I.; Lee, M.P.

1994-09-01

Nuclear Regulatory Commission regulations for the disposal of spent nuclear fuel and high-level radioactive waste in a geologic repository recognize that fault displacement is a potentially adverse condition. However, they do not prohibit designing the geologic repository against the effects of such a potentially adverse condition. This Staff Technical Position recognizes the acceptability of designing the geologic repository to take into account the attendant effects (e.g., displacement) of faults of regulatory concern and expresses the staff's views on what is needed from the US Department of Energy if it chooses to locate structures, systems, and components important to safety or important to waste isolation in areas that contain faults of regulatory concern

Managing and Evaluating Digital Repositories

Science.gov (United States)

Zuccala, Alesia; Oppenheim, Charles; Dhiensa, Rajveen

2008-01-01

Introduction: We examine the role of the digital repository manager, discuss the future of repository management and evaluation and suggest that library and information science schools develop new repository management curricula. Method: Face-to-face interviews were carried out with managers of five different types of repositories and a Web-based…

Repository simulation tests

International Nuclear Information System (INIS)

Wicks, G.G.; Bibler, N.E.; Jantzen, C.M.; Plodinec, M.J.

1984-01-01

The repository simulation experiments described in this paper are designed to assess the performance of SRP waste glass under the most realistic repository conditions that can be obtained in the laboratory. These tests simulate the repository environment as closely as possible and introduce systematically the variability of the geology, groundwater chemistry, and waste package components during the leaching of the waste glass. The tests evaluate waste form performance under site-specific conditions, which differ for each of the geologic repositories under consideration. Data from these experiments will aid in the development of a realistic source term that can describe the release of radionuclides from SRP waste glass as a component of proposed waste packages. Hence, this information can be useful to optimize waste package design for SRP waste glass and to provide data for predicting long-term performance and subsequent conformance to regulations. The repository simulation tests also help to bridge the gap in interpreting results derived from tests performed under the control of the laboratory to the uncertainity and variability of field tests. In these experiments, site-specific repository components and conditions are emphasized and only the site specific materials contact the waste forms. An important feature of these tests is that both actual and simulated waste glasses are tested identically. 7 figures, 2 tables

GIS for the needs of the Radioactive Waste Repository Authority

Directory of Open Access Journals (Sweden)

Jitka Mikšová

2007-06-01

Full Text Available The Radioactive Waste Repository Authority (RAWRA is a state organisation responsible for the management of activities related to the disposal of all existing and future radioactive waste and spent nuclear fuel classed as a waste in Czech Republic. Worldwide, a deep geological repository is considered the highest degree of safety for a nuclear waste disposal. Such a repository has to be built in a stable geological environment ensuring the isolation of the stored radioactive waste from the surrounding environment for a long period of time. The selection of suitable site for the deep geological repository construction is a complicated and long term process. Considering this fact and also in respect to an assumed volume of varied datasets the GIS RAWRA was established to ensure convenient management and availability of data containing spatial information.The system is based on ESRI (ArcInfo including extensions, ArcSDE, ArcIMS, Leica Geosystems (Image Analysis and Microsoft software (MS SQL Server. Resulting datasets from six recommended potentially suitable sites for the location of a geological repository have been incorporated into the geodatabase to date. The necessary analysis was made using ESRI software tools and, in addition, custom applications were developed including the metadata editor, etc. This analysis was carried out with respect to existing geological and non-geological criteria defined for a nuclear waste repository. Finally, all six investigated sites with a total area of 240 km2 were reduced in area, each of them resulting in an area of approximately 10km2 for further detailed characterisation.

Recharge-area nuclear waste repository in southeastern Sweden. Demonstration of hydrogeologic siting concepts and techniques

International Nuclear Information System (INIS)

Provost, A.M.; Voss, C.I.

2001-11-01

Nuclear waste repositories located in regional ground-water recharge ('upstream') areas may provide the safety advantage that potentially released radionuclides would have long travel time and path length, and large path volume, within the bedrock before reaching the biosphere. Nuclear waste repositories located in ground-water discharge ('downstream') areas likely have much shorter travel time and path length and smaller path volume. Because most coastal areas are near the primary discharge areas for regional ground-water flow, coastal repositories may have a lower hydrogeologic safety margin than 'upstream' repositories located inland. Advantageous recharge-area sites may be located through careful use of regional three-dimensional, variable-density, ground-water modeling. Because of normal limitations of site-characterization programs in heterogeneous bedrock environments, the hydrogeologic structure and properties of the bedrock will generally remain unknown at the spatial scales required for the model analysis, and a number of alternative bedrock descriptions are equally likely. Model simulations need to be carried out for the full range of possible descriptions. The favorable sites are those that perform well for all of the modeled bedrock descriptions. Structural heterogeneities in the bedrock and local undulations in water-table topography, at a scale finer than considered by a given model, also may cause some locations in favored inland areas to have very short flow paths (of only hundreds of meters) and short travel times, compromising the long times and paths (of many kilometers) predicted by the analysis for these sites. However, in the absence of more detailed modeling, the favored upstream sites offer a greater chance of achieving long times and paths than do downstream discharge areas, where times and paths are expected to be short regardless of the level of detail included in the model. As an example of this siting approach, potential repository

The repository ecology an approach to understanding repository and service interactions

CERN Document Server

CERN. Geneva; Hagemann, Melissa

2007-01-01

An increasing number of university institutions and other organisations are deciding to deploy repositories and a growing number of formal and informal distributed services are supporting or capitalising on the information these repositories provide. Despite reasonably well understood technical architectures, early majority adopters may struggle to articulate their place within the actualities of a wider information environment. The idea of a repository ecology provides developers and administrators with a useful way of articulating and analysing their place in the information environment, and the technical and organisational interactions they have, or are developing, with other parts of such an environment. This presentation will provide an overview of the concept of a repository ecology and examine some examples from the domains of scholarly communications and elearning.

Establishment of IAEA knowledge of integrity of the geological repository boundaries and disposed spent fuel assemblies in the context of the Finnish geological repository. Experts' Group meeting Report on Task JNT/C 1204 of the Member States' Support Programme to IAEA Safeguards

International Nuclear Information System (INIS)

Okko, O.

2004-05-01

The Geological Repository Safeguards Experts Group (Member State Support Programme tasks JNT/C1204 and C1226), agreed that annual meetings should be held to address interface issues between IAEA safeguards and radioactive waste management and to explore the use of safety and operational information to make International Atomic Energy Agency (IAEA) safeguards more effective and efficient for geological repository facilities. It has also been recognised that the safeguards measures for geological repositories are to be developed site-specifically. To address these issues to the planned Olkiluoto repository in Finland a meeting of experts in safety, geological repository operations,and safeguards from 6 States, European Commission, and IAEA was held in Olkiluoto and Rauma, Finland, during September 29 - October 4, 2003. The pre-operational phase of the Olkiluoto repository should be efficiently used by the parties involved in safeguards. The applicability and reliability of the potential new techniques and the efficient practices must be developed and proven before their implementation as safeguards measures to be applied at the subsequent stages of the repository development. The visit to the location of the proposed Olkiluoto repository and neighbouring areas and subsequent presentations enabled the working groups to discuss the various issues with reference to actual site conditions. The working groups were thus able to identify potential measurement and monitoring techniques and research and development requirements for consideration by the Finnish authorities, in addition to making recommendations to the IAEA on planned activities for carrying out before and during the early investigation phase of the proposed Olkiluoto repository. It was understood that all parties shall take good care of the implementation of the planned activities to ensure that proven means, approaches and the required verified information is at hand at the time the projected facility will

General conceptual design study for a high-level radioactive waste repository in a granite formation

International Nuclear Information System (INIS)

1982-01-01

The object of the general conceptual design study for a high level radioactive wastes repository in a deep lying granite formation is to ensure that technology available in 1980 is suitable for building, operating and finally closing such a repository. It is feasible to build and operate a 1000 m deep repository, located in a granite batholith, receiving 30000 AVM canisters (after 30 years surface cooling), the disposal rate being 1000 canisters per year. Cost of the operation amounts to 1,3% of the corresponding amount of electricity. The building, operating and final closing phases will take 81 years

Building and Using Digital Repository Certifications across Science

Science.gov (United States)

McIntosh, L.

2017-12-01

When scientific recommendations are made based upon research, the quality and integrity of the data should be rigorous enough to verify claims and in a trusted location. Key to ensuring the transparency and verifiability of research, reproducibility hinges not only on the availability of the documentation, analyses, and data, but the ongoing accessibility and viability of the files and documents, enhanced through a process of curation. The Research Data Alliance (RDA) is an international, community-driven, action-oriented, virtual organization committed to enabling the open sharing of data by building social and technical bridges. Within the RDA, multiple groups are working on consensus-building around the certification of digital repositories across scientific domains. For this section of the panel, we will discuss the work to date on repository certification from this RDA perspective.

Representation of an open repository in groundwater flow models

International Nuclear Information System (INIS)

Painter, Scott; Sun, Alexander

2005-08-01

The effect of repository tunnels on groundwater flow has been identified as a potential issue for the nuclear waste repository being considered by SKB for a fractured granite formation in Sweden. In particular, the following pre-closure and post-closure processes have been identified as being important: inflows into open tunnels as functions of estimated grouting efficiencies, drawdown of the water table in the vicinity of the repository, upcoming of saline water, 'turnover' of surface water in the upper bedrock, and resaturation of backfilled tunnels following repository closure. The representation of repository tunnels within groundwater models is addressed in this report. The primary focus is on far-field flow that is modeled with a continuum porous medium approximation. Of particular interest are the consequences of the tunnel representation on the transient response of the groundwater system to repository operations and repository closure, as well as modeling issues such as how the water-table free surface and the coupling to near-surface hydrogeology should be handled. The overall objectives are to understand the consequences of current representations and to identify appropriate approximations for representing open tunnels in future groundwater modeling studies. The following conclusions can be drawn from the results of the simulations: 1. Two-phase flow may be induced in the vicinity of repository tunnels during repository pre-closure operations, but the formation of a two-phase flow region will not significantly affect far-field flow or inflows into tunnels. 2. The water table will be drawn down to the repository horizon and tunnel inflows will reach a steady-state value within about 5 years. 3. Steady-state inflows at the repository edge are estimated to be about 250 m 3 /year per meter of tunnel. Inflows will be greater during the transient de-watering period and less for tunnel locations closer to the repository center. 4. Significant amounts of water

Representation of an open repository in groundwater flow models

Energy Technology Data Exchange (ETDEWEB)

Painter, Scott; Sun, Alexander [Southwest Research Inst., San Antonio, TX (United States). Center for Nuclear Waste Regulatory Analyses

2005-08-01

The effect of repository tunnels on groundwater flow has been identified as a potential issue for the nuclear waste repository being considered by SKB for a fractured granite formation in Sweden. In particular, the following pre-closure and post-closure processes have been identified as being important: inflows into open tunnels as functions of estimated grouting efficiencies, drawdown of the water table in the vicinity of the repository, upcoming of saline water, 'turnover' of surface water in the upper bedrock, and resaturation of backfilled tunnels following repository closure. The representation of repository tunnels within groundwater models is addressed in this report. The primary focus is on far-field flow that is modeled with a continuum porous medium approximation. Of particular interest are the consequences of the tunnel representation on the transient response of the groundwater system to repository operations and repository closure, as well as modeling issues such as how the water-table free surface and the coupling to near-surface hydrogeology should be handled. The overall objectives are to understand the consequences of current representations and to identify appropriate approximations for representing open tunnels in future groundwater modeling studies. The following conclusions can be drawn from the results of the simulations: 1. Two-phase flow may be induced in the vicinity of repository tunnels during repository pre-closure operations, but the formation of a two-phase flow region will not significantly affect far-field flow or inflows into tunnels. 2. The water table will be drawn down to the repository horizon and tunnel inflows will reach a steady-state value within about 5 years. 3. Steady-state inflows at the repository edge are estimated to be about 250 m{sup 3}/year per meter of tunnel. Inflows will be greater during the transient de-watering period and less for tunnel locations closer to the repository center. 4. Significant

Salt Repository Project site study plan for seismographic monitoring: Revision 1

International Nuclear Information System (INIS)

1987-01-01

This site study plan describes the seismographic monitoring activities to be conducted during the early stages of Site Characterization at the Deaf Smith County site, Texas. The field programs has been designed to provide data useful in addressing information/data needs resulting from Federal/State/local regulatory requirements and repository program requirements. Sixteen new and three relocated seismographic stations will be added to the now existing network of 13 stations for a total of 32 stations in the network. The areal extent is being expanded and selected regions covered more densely to provide more accurate monitoring and location of microearthquakes. More sophisticated instruments are being used at selected locations to allow for more detailed analysis. A few seismographs are being installed at depth to provide a limited 3-D monitoring network in the area of the repository. The Salt Repository Project (SRP) Networks specify the schedule under which the program will operate. The Technique Field Services Contractor (TFSC) is responsible for conducting the field program. Data will be handled and reported in accordance with established SRP procedures. A quality assurance program will be utilized to assure that activities affecting quality are performed correctly and that appropriate documentation is maintained. 32 refs., 11 figs., 4 tabs

Project Guarantee 1985. Final repository for high-level radioactive wastes: The system of safety barriers

International Nuclear Information System (INIS)

Anon.

1985-01-01

Final disposal of radioactive waste involves preventing the waste from returning from the repository location into the biosphere by means of successively arranged containment measures known as safety barriers. In the present volume NGB 85-04 of the series of reports for Project 'Guarantee' 1985, the safety barrier system for the type C repository for high-level waste is described. The barrier parameters which are relevant for safety analysis are quantified and associated error limits and data scatter are given. The aim of the report is to give a summary documentation of the safety analysis input data and their scientific background. For secure containment of radioactive waste safety barriers are used which effectively limit the release of radioactive material from the repository (release barriers) and effectively retard the entry of the original radioactive material into the biosphere (time barriers). Safety barriers take the form of both technically constructed containment measures and the siting of the repository in suitable geological formations. The technical safety barrier system in the case of high-level waste comprises: the waste solidification matrix (borosilicate glass), massive steel canisters, encasement of the waste canisters, encasement of the waste canisters in highly compacted bentonite, sealing of vacant storage space and access routes on repository closure. The natural geological safety barriers - the host rock and overlying formations provide sufficiently long deep groundwater flow times from the repository location to the earth's surface and for additional lengthening of radionuclide migration times by means of various chemical and physical retardation mechanisms. The stability of the geological formations is so great that hydrogeological system is protected for a sufficient length of time from deterioration caused, in particular, by erosion. Observations in the final section of the report indicate that input data for the type C repository safety

Salt Repository Project: Data report on corrosion results obtained from excess-salt corrosion test Matrix 1

International Nuclear Information System (INIS)

Haberman, J.H.; Westerman, R.E.

1987-05-01

The test discussed in this data report was directed at determining the response of the reference A216 grade WCA steel when it is exposed to anoxic excess-salt conditions at 150 0 C. The environment used in the test was intended to duplicate the intrusion brine scenario (i.e., the formation of brine by the intrusion of water from an outside source into the repository, with the formation of brine through dissolution of salt from the repository horizon). The salt-brine environment used in the test therefore reflected the expected gross salt composition of the repository horizon

Study of environmental conditions in the repositories of the National Archive of the Republic of Cuba

Directory of Open Access Journals (Sweden)

Isbel Vivar González

2016-01-01

Full Text Available The aim was to study the behavior of the temperature (T, relative humidity (RH and illuminance (I in the repositories of the National Archive of the Republic of Cuba. The values of T and RH were measured twice daily for four consecutive years. I was measured in sunny and cloudy days. The result sallow us to affirm that the environmental conditions (T, RH of these repositories are favorable for the conservation of paper documents. In cloudy days, I of the repositories located in lower-ground floor does not exceed the allowed 50 lux; but in sunny days, due to the incidence of sunlight, in all repositories I exceeds 50 lux. Artificial light caused an increase in I in all repositories, but this is not significant because the light bulbs are kept turned off most of the time.

Engineered barrier development for a nuclear waste repository in basalt

International Nuclear Information System (INIS)

Smith, M.J.

1980-05-01

The BWIP Engineered Barrier Program has been developed to provide an integrated approach to the development of site-specific Engineered Barrier assemblages for a repository located in basalt. The goal of this program is to specify engineered and natural barriers which will ensure that nuclear and non-radioactive hazardous materials emplaced in a repository in basalt do not exceed acceptable rates of release to the biosphere. A wide range of analytical and experimental activities related to the basalt repository environment, waste package environment, waste/barrier/rock interactions, and barrier performance assessment provide the basis for selection of systems capable of meeting licensing requirements. Work has concentrated on specifying and testing natural and man-made materials which can be used to plug boreholes in basalt and which can be used as multiple barriers to surround nuclear waste forms and containers. The Engineered Barriers Program is divided into two major activities: multiple barrier studies and borehole plugging. 8 figures, 4 tables

Building on existing institutions to perpetuate knowledge of waste repositories

International Nuclear Information System (INIS)

Weitzberg, A.

1982-08-01

Purpose of this report is to examine the function of several existing institutions and to show how they could be effectively used to transmit information about waste repositories for long times into the future. Scope of this report is limited to a discussion of four institutional approaches to the dissemination and retention of information: Widely distributed maps, the marker system of the National Geodetic Survey, the archiving of documents, and one-call systems designed to protect underground utility installations from inadvertent damage by the public. Each of these approaches is discussed in an independent section that describes the background of the institutional approach, discusses methods for applying it to waste repositories, and assesses its potential value. The sole intent of this report is to present supporting data for future decisions about the kinds of communication measures that should be implemented to advise future generations about the locations and hazards of waste repositories

The repository ecology: an approach to understanding repository and service interactions

CERN Multimedia

CERN. Geneva

2007-01-01

An increasing number of university institutions and other organisations are deciding to deploy repositories and a growing number of formal and informal distributed services are supporting or capitalising on the information these repositories provide. Despite reasonably well understood technical architectures, early majority adopters may struggle to articulate their place within the actualities of a wider information environment. The idea of a repository ecology provides developers and administrators with a useful way of articulating and analysing their place in the information environment, and the technical and organisational interactions they have, or are developing, with other parts of such an environment. This presentation will provide an overview of the concept of a repository ecology and examine some examples from the domains of scholarly communications and elearning. View John Robertson's biography

Literature survey on solid and aqueous species of importance for nuclear waste repositories: The elements uranium, neptunium and cesium

International Nuclear Information System (INIS)

Bucher, J.J.

1987-01-01

This document contains extensive tables listing all possible chemical compounds of species that might occur in a proposed nuclear waste repository. Most are listed as unlikely to occur under conditions predicted for the repository. Extensive data tables and reference sources are provided for those compounds that might occur on form

Monitored Geologic Repository Concept of Operations

International Nuclear Information System (INIS)

Curry, P.M.

1999-01-01

This updated document provides the top level guidance for development of the individual systems for the MGR which will be further developed in the System Description Documents. This document will serve as guidance for the development of functional interface and operational requirements. However, the data and engineering values presented in Monitored Geologic Repository Concept of Operations are provided as estimates or summaries of the current design. The original analyses or supporting documents must be utilized if the data or engineering values are used for design inputs. The concepts presented will be utilized as inputs for the development of operational concepts for the individual systems. It is recognized that the references listed may contain existing data or data which are to be verified. However, the data and engineering values presented will not impact the concepts presented in this technical document. As such, the data and engineering values are not being tracked as To Be Verified data. This revision was created to incorporate changes resulting from Enhanced Design Alternative II and Revision 3, DCN 01, of the Monitored Geologic Repository Requirements (YMP 1999)

Mechanical stability of repository tunnels and factors to be considered for determining tunnel spacing

International Nuclear Information System (INIS)

Takeuchi, Kunifumi

1994-01-01

Kristallin-1 organized by Nagra is currently advanced as a synthetic project regarding a high level radioactive waste (HLW) repository in Switzerland. Its host rock is granitic rocks, and the potential siting area is located in northern Switzerland. The objective of this project is to demonstrate the long term safety of a HLW repository under more site-specific conditions than before. As the detailed geological data were investigated, the average size of undisturbed crystalline rock blocks is limited horizontally to about several hundred meter, therefore, the HLW repository area must be divided into several panels to avoid fracture zones. It is necessary to make tunnel spacing as small as possible for the purpose of reasonably designing the entire layout of repository tunnels. The main factors to be considered for determining repository tunnel spacing are listed. Rock mass modeling, rock mass material properties, the analysis model and parameters, the numerical analysis of repository tunnel stability and its main conclusion are reported. The numerical analysis of the temperature distribution in near field was carried out. Tunnel spacing should be set more than 20 m in view of the maximum temperature. (K.I.)

Thermal analyses of spent nuclear fuel repository

International Nuclear Information System (INIS)

Ikonen, K.

2003-06-01

This report contains the temperature dimensioning of the KBS-3V type 1- or 2-panel repository based on the rock properties measured from the Olkiluoto investigations. The report describes first the development of a calculation methodology for the thermal analysis of a repository for nuclear fuel. The disposed canisters produce residual heat due to decay (or disintegration) of radioactive products. The decay heat is conducted to surrounding rock mass. The methods were applied to determine the effect of different parameters on the highest canister temperature and to support the planning, dimensioning and operation of the repository. The thermal diffusivity of the rock is low and the heat released from the canisters is spread into the surrounding rock volume quite slowly causing thermal gradient in the rock close to canisters and the canister temperature is increased remarkably. The maximum temperature on the canister surface is limited to the design temperature of +100 deg C. However, due to uncertainties in thermal analysis parameters (like scattering in rock conductivity) the allowable calculated maximum canister temperature is set to 90 deg C causing a safety margin of 10 deg C. The allowable temperature is controlled by the spacing between adjacent canisters, adjacent tunnels and the distance between separate panels of the repository and the pre-cooling time affecting power of the canisters. Because of the fact that the disposal operation takes several decades, the moment of disposal of an individual canister in addition to the location has an influence on the maximum temperature in the canister. Also, a second disposal panel in the repository has a thermal interaction with the other panel. This interaction is expressed after a few decades at the strongest. It became apparent that the temperature of canister surfaces can be determined by analytic line heat source model much more efficiently than by numerical analysis, if the analytic model is first verified and

Hydrologic issues in repository siting

International Nuclear Information System (INIS)

Remson, I.; Gorelick, S.M.

1982-01-01

Extrapolation of Darcy's law to the transport of water an solutes in unfractured poorly permeable rocks being studied for nuclear waste disposal is questioned. The hydrologic literature includes numerous references to both non-Darcian flow in dense materials devoid of macrofractures and microfractures and to threshold gradients below which no flow occurs. For such situations to occur, the pore-size range must be small enough so that all pore water is sufficiently close to mineral surfaces to be affected by the surficial forces. Then the flow will be non-Newtonian and non-Darcian, and solute transport will be by molecular diffusion. If fluid transport in very dense unfractured rocks is non-Darcian, useful methods of testing candidate host rocks become apparent. In situ nondestructive pressure testing of canister waste emplacement boreholes in a mined repository can verify the absence of both fracture flow and Darcian flow. 18 references

Anticipated Degradation Modes of Metallic Engineered Barriers for High-Level Nuclear Waste Repositories

Science.gov (United States)

Rodríguez, Martín A.

2014-03-01

Metallic engineered barriers must provide a period of absolute containment to high-level radioactive waste in geological repositories. Candidate materials include copper alloys, carbon steels, stainless steels, nickel alloys, and titanium alloys. The national programs of nuclear waste management have to identify and assess the anticipated degradation modes of the selected materials in the corresponding repository environment, which evolves in time. Commonly assessed degradation modes include general corrosion, localized corrosion, stress-corrosion cracking, hydrogen-assisted cracking, and microbiologically influenced corrosion. Laboratory testing and modeling in metallurgical and environmental conditions of similar and higher aggressiveness than those expected in service conditions are used to evaluate the corrosion resistance of the materials. This review focuses on the anticipated degradation modes of the selected or reference materials as corrosion-resistant barriers in nuclear repositories. These degradation modes depend not only on the selected alloy but also on the near-field environment. The evolution of the near-field environment varies for saturated and unsaturated repositories considering backfilled and unbackfilled conditions. In saturated repositories, localized corrosion and stress-corrosion cracking may occur in the initial aerobic stage, while general corrosion and hydrogen-assisted cracking are the main degradation modes in the anaerobic stage. Unsaturated repositories would provide an oxidizing environment during the entire repository lifetime. Microbiologically influenced corrosion may be avoided or minimized by selecting an appropriate backfill material. Radiation effects are negligible provided that a thick-walled container or an inner shielding container is used.

THERMAL CONDUCTIVITY OF NON-REPOSITORY LITHOSTRATIGRAPHIC LAYERS

Energy Technology Data Exchange (ETDEWEB)

R. JONES

2004-10-22

This model report addresses activities described in ''Technical Work Plan for: Near-Field Environment and Transport Thermal Properties and Analysis Reports Integration'' (BSC 2004 [DIRS 171708]). The model develops values for thermal conductivity, and its uncertainty, for the nonrepository layers of Yucca Mountain; in addition, the model provides estimates for matrix porosity and dry bulk density for the nonrepository layers. The studied lithostratigraphic units, as identified in the ''Geologic Framework Model'' (GFM 2000) (BSC 2004 [DIRS 170029]), are the Timber Mountain Group, the Tiva Canyon Tuff, the Yucca Mountain Tuff, the Pah Canyon Tuff, the Topopah Spring Tuff (excluding the repository layers), the Calico Hills Formation, the Prow Pass Tuff, the Bullfrog Tuff, and the Tram Tuff. The deepest model units of the GFM (Tund and Paleozoic) are excluded from this study because no data suitable for model input are available. The parameter estimates developed in this report are used as input to various models and calculations that simulate heat transport through the rock mass. Specifically, analysis model reports that use product output from this report are: (1) Drift-scale coupled processes (DST and TH seepage) models; (2) Drift degradation analysis; (3) Multiscale thermohydrologic model; and (4) Ventilation model and analysis report. In keeping with the methodology of the thermal conductivity model for the repository layers in ''Thermal Conductivity of the Potential Repository Horizon'' (BSC 2004 [DIRS 169854]), the Hsu et al. (1995 [DIRS 158073]) three-dimensional (3-D) cubic model (referred to herein as ''the Hsu model'') was used to represent the matrix thermal conductivity as a function of the four parameters (matrix porosity, thermal conductivity of the saturating fluid, thermal conductivity of the solid, and geometric connectivity of the solid). The Hsu model requires input data

MetaboLights: An Open-Access Database Repository for Metabolomics Data.

Science.gov (United States)

Kale, Namrata S; Haug, Kenneth; Conesa, Pablo; Jayseelan, Kalaivani; Moreno, Pablo; Rocca-Serra, Philippe; Nainala, Venkata Chandrasekhar; Spicer, Rachel A; Williams, Mark; Li, Xuefei; Salek, Reza M; Griffin, Julian L; Steinbeck, Christoph

2016-03-24

MetaboLights is the first general purpose, open-access database repository for cross-platform and cross-species metabolomics research at the European Bioinformatics Institute (EMBL-EBI). Based upon the open-source ISA framework, MetaboLights provides Metabolomics Standard Initiative (MSI) compliant metadata and raw experimental data associated with metabolomics experiments. Users can upload their study datasets into the MetaboLights Repository. These studies are then automatically assigned a stable and unique identifier (e.g., MTBLS1) that can be used for publication reference. The MetaboLights Reference Layer associates metabolites with metabolomics studies in the archive and is extensively annotated with data fields such as structural and chemical information, NMR and MS spectra, target species, metabolic pathways, and reactions. The database is manually curated with no specific release schedules. MetaboLights is also recommended by journals for metabolomics data deposition. This unit provides a guide to using MetaboLights, downloading experimental data, and depositing metabolomics datasets using user-friendly submission tools. Copyright © 2016 John Wiley & Sons, Inc.

Radioactive wastes repository in Temascalapa, State of Mexico, public opinion. Determination of health effects

International Nuclear Information System (INIS)

Solis Tinoco, E.

1998-01-01

Nuclear waste usually concerns public about the impact on public health and the environment. In Mexico, such interest exists, particularly in the Temascalapa Municipality, Mexico where a low level waste repository recognized by the IAEA, has been functioning since 1972. Maquixco repository is located at 42 Kilometers northeast of Mexico City. Although the environmental radiological monitoring records have demonstrated negligible impact on the environment, in 1998 an unusual public polemic on radioactive health effects appeared among Temascalapa residents. This paper presents a research performed during 1998 with the participation of the National Nuclear Research Institute of Mexico and the National Autonomous University of Mexico. The research design allowed the involvement of local authorities, as a way of stimulate public participation. The research was performed in nine locations of the Temascalapa Municipality, it was focused on public polemics, associated to Maquixco repository as well as trying to identify demographic factors that exert influence on public attitudes. There are also presented the results of personal dosimetry analysis performed on a four hundred residents sample of this Municipality. (Author)

Hydrothermal evolution of repository groundwaters in basalt

International Nuclear Information System (INIS)

Apps, J.A.

1984-01-01

Groundwaters in the near field of a radioactive waste repository in basalt will change their chemical composition in response to reactions with the basalt. These reactions will be promoted by the heat generated by the decaying waste. It is important to predict both the rate and the extent of these reactions, and the secondary minerals produced, because the alteration process controls the chemical environment affecting the corrosion of the canister, the solubility and complexation of migrating radionuclides, the reactivity of the alteration products to radionuclides sorption, and the porosity and permeability of the host rock. A comprehensive review of the literature leads to the preliminary finding that hydrothermally altering basalts in geothermal regions such as Iceland lead to a secondary mineralogy and groundwater composition similar to that expected to surround a repository. Furthermore, laboratory experiments replicating the alteration conditions approximate those observed in the field and expected in a repository. Preliminary estimates were made of the rate of hydration and devitrification of basaltic glass and the zero-order dissolution rate of basaltic materials. The rates were compared with those for rhyolitic glasses and silicate minerals. Preliminary calculations made of mixed process alteration kinetics, involving pore diffusion and surface reaction suggest that at temperatures greater than 150 0 C, alteration proceeds so rapidly as to become pervasive in normally fractured basalt exposed to higher temperatures in the field. 70 references

Development of the Korean Reference Vertical Disposal System Concept for Spent Fuels

International Nuclear Information System (INIS)

Lee, J.Y.; Cho, D.K.; Kim, S.G.; Choi, H.J.; Choi, J.W.; Hahn, P.S.

2006-01-01

The development of a deep geologic disposal system for the spent fuel from nuclear power plants has been carried out since this program was launched at 1997 in Korea. In ' this paper, a pre-conceptual design of the Korean Reference HLW Vertical disposal System (KRS-V1) is presented. Though no site for the underground repository has yet been specified in Korea, a generic site with granitic rock is considered for reference HLW repository design. Depth of the repository is assumed to be 500 meters. The repository consists of the disposal area, technical rooms with four shafts to connect them to the ground level in the controlled area and technical rooms with an access tunnel and three shafts to connect them to the ground level in the uncontrolled area. Disposal area consists of disposal tunnels, panel tunnels and a central tunnel. The repository will be excavated, operated and backfilled in several phases including an Underground Research Laboratory (URL) phase. The result of this preliminary conceptual design will be used for an evaluation of the feasibility, analyses of the long term safety, information for public communication and a cost estimation etc. (authors)

Repository operational criteria analysis

International Nuclear Information System (INIS)

Hageman, J.P.; Chowdhury, A.H.

1992-08-01

The objective of the ''Repository Operational Criteria (ROC) Feasibility Studies'' (or ROC task) was to conduct comprehensive and integrated analyses of repository design, construction, and operations criteria in 10 CFR Part 60 regulations, considering the interfaces and impacts of any potential changes to those regulations. The study addresses regulatory criteria related to the preclosure aspects of the geologic repository. The study task developed regulatory concepts or potential repository operational criteria (PROC) based on analysis of a repository's safety functions and other regulations for similar facilities. These regulatory concepts or PROC were used as a basis to assess the sufficiency and adequacy of the current criteria in 10 CFR Part 60. Where the regulatory concepts were same as current operational criteria, these criteria were referenced. The operations criteria referenced or the PROC developed are given in this report. Detailed analyses used to develop the regulatory concepts and any necessary PROC for those regulations that may require a minor change are also presented. The results of the ROC task showed a need for further analysis and possible major rule change related to the design bases of a geologic repository operations area, siting, and radiological emergency planning

Consortial routes to effective repositories

OpenAIRE

Moyle, M.; Proudfoot, R.

2009-01-01

A consortial approach to the establishment of repository services can help a group of Higher Education Institutions (HEIs) to share costs, share technology and share expertise. Consortial repository work can tap into existing structures, or it can involve new groupings of institutions with a common interest in exploring repository development. This Briefing Paper outlines some of the potential benefits of collaborative repository activity, and highlights some of the technical and organisation...

Aerosol particle transport modeling for preclosure safety studies of nuclear waste repositories

International Nuclear Information System (INIS)

Gelbard, F.

1989-01-01

An important concern for preclosure safety analysis of a nuclear waste repository is the potential release to the environment of respirable aerosol particles. Such particles, less than 10 μm in aerodynamic diameter, may have significant adverse health effects if inhaled. To assess the potential health effects of these particles, it is not sufficient to determine the mass fraction of respirable aerosol. The chemical composition of the particles is also of importance since different radionuclides may pose vastly different health hazards. Thus, models are needed to determine under normal and accident conditions the particle size and the chemical composition distributions of aerosol particles as a function of time and of position in the repository. In this work a multicomponent sectional aerosol model is used to determine the aerosol particle size and composition distributions in the repository. A range of aerosol mass releases with varying mean particle sizes and chemical compositions is used to demonstrate the sensitivities and uncertainties of the model. Decontamination factors for some locations in the repository are presented. 8 refs., 1 tab

Uncertainty management in radioactive waste repository site assessment

International Nuclear Information System (INIS)

Baldwin, J.f.; Martin, T.P.; Tocatlidou

1994-01-01

The problem of performance assessment of a site to serve as a repository for the final disposal of radioactive waste involves different types of uncertainties. Their main sources include the large temporal and spatial considerations over which safety of the system has to be ensured, our inability to completely understand and describe a very complex structure such as the repository system, lack of precision in the measured information etc. These issues underlie most of the problems faced when rigid probabilistic approaches are used. Nevertheless a framework is needed, that would allow for an optimal aggregation of the available knowledge and an efficient management of the various types of uncertainty involved. In this work a knowledge-based modelling of the repository selection process is proposed that through a consequence analysis, evaluates the potential impact that hypothetical scenarios will have on a candidate site. The model is organised around a hierarchical structure, relating the scenarios with the possible events and processes that characterise them, and the site parameters. The scheme provides for both crisp and fuzzy parameter values and uses fuzzy semantic unification and evidential support logic reference mechanisms. It is implemented using the artificial intelligence language FRIL and the interaction with the user is performed through a windows interface

Repository design

Energy Technology Data Exchange (ETDEWEB)

John, C M

1982-01-01

Various technical issues of radioactive waste design are addressed in this paper. Two approaches to repository design considered herein are: (1) design to minimize the disturbance of the hot rock; and (2) designs that intentionally modify the hot rock to insure better containment of the wastes. The latter designs range from construction of a highly impermeable barrier around a spherical cavern to creating a matrix of tunnels and boreholes to form a cage within which the hydraulic pressure is nearly constant. Examples of these design alternatives are described in some detail. It is concluded that proposed designs for repositories illustrate that performance criteria considered acceptable for such facilities can be met by appropriate site selection and repository engineering. With these technically feasible design concepts, it is also felt that socioeconomic and institutional issues can be better resolved. (BLM)

Release consequence analysis for a hypothetical geologic radioactive waste repository in salt

International Nuclear Information System (INIS)

1979-08-01

One subtask conducted under the INFCE program is to evaluate and compare the health and safety impacts of different fuel cycles in which all radioactive wastes (except those from mining and milling) are placed in a geologic repository in salt. To achieve this objective, INFCE Working Group 7 examined the radiologic dose to humans from geologic repositories containing waste arisings as defined for seven reference fuel cycles. This report examines the release consequences for a generic waste repository in bedded salt. The top of the salt formation and the top of the repository are assumed to be 250 and 600 m, respectively, below the surface. The hydrogeologic structure above the salt consists of two aquifers and two aquitards. The aquifers connect to a river 6.2 km from the repository. The regional gradient to the river is 1 m/km in all aquifers. Hydrologic, transport, and dose models were used to model two release scenarios for each fuel cycle, one without a major disturbance and one in which a major geologic perturbation breached the repository immediately after it was sealed. The purpose of the modeling was to predict the rate of transport of radioactive contaminants from the repository through the geosphere to the biosphere, and to determine the potential dose to humans. Of the many radionuclides in the waste, only 129 I and 226 Ra arrived at the river in sufficient concentrations for a measurable dose calculation. Radionuclide concentrations in the ground water pose no threat to man because the ground water is a concentrated brine and it is diluted by a factor of 10 6 to 10 7 upon entering the river

Progress on the national low level radioactive waste repository and national intermediate level waste store

International Nuclear Information System (INIS)

Perkins, C.

2003-01-01

The Australian Government is committed to establishing two purpose-built facilities for the management of Australia's radioactive waste; the national repository for disposal of low level and short-lived intermediate level ('low level') waste, and the national store for storage of long-lived intermediate level ('intermediate level') waste. It is strongly in the interests of public security and safety to secure radioactive waste by disposal or storage in facilities specially designed for this purpose. The current arrangements where waste is stored under ad hoc arrangements at hundreds of sites around Australia does not represent international best practice in radioactive waste management. Environmental approval has been obtained for the national repository to be located at Site 40a, 20 km east of Woomera in South Australia, and licences are currently being sought from the Australian Radiation Protection and Nuclear Safety Agency (ARPANSA) to site, construct and operate the facility. The national repository may be operating in 2004 subject to obtaining the required licences. The national store will be located on Australian Government land and house intermediate level waste produced by Australian Government departments and agencies. The national store will not be located in South Australia. Short-listing of potentially suitable sites is expected to be completed soon

Centralized mouse repositories.

Science.gov (United States)

Donahue, Leah Rae; Hrabe de Angelis, Martin; Hagn, Michael; Franklin, Craig; Lloyd, K C Kent; Magnuson, Terry; McKerlie, Colin; Nakagata, Naomi; Obata, Yuichi; Read, Stuart; Wurst, Wolfgang; Hörlein, Andreas; Davisson, Muriel T

2012-10-01

Because the mouse is used so widely for biomedical research and the number of mouse models being generated is increasing rapidly, centralized repositories are essential if the valuable mouse strains and models that have been developed are to be securely preserved and fully exploited. Ensuring the ongoing availability of these mouse strains preserves the investment made in creating and characterizing them and creates a global resource of enormous value. The establishment of centralized mouse repositories around the world for distributing and archiving these resources has provided critical access to and preservation of these strains. This article describes the common and specialized activities provided by major mouse repositories around the world.

Demystifying the institutional repository for success

CERN Document Server

Buehler, Marianne

2013-01-01

Institutional repositories remain key to data storage on campus, fulfilling the academic needs of various stakeholders. Demystifying the Institutional Repository for Success is a practical guide to creating and sustaining an institutional repository through marketing, partnering, and understanding the academic needs of all stakeholders on campus. This title is divided into seven chapters, covering: traditional scholarly communication and open access publishing; the academic shift towards open access; what the successful institutional repository looks like; institutional repository collaboratio

Investigation of excavation stability in a finite repository

International Nuclear Information System (INIS)

St John, C.M.; Mitchell, S.J.

1987-05-01

Two-dimensional thermal-mechanical analyses of a hypothetical repository in tuff were performed using a boundary-element computer code, with the objective of investigating the relative stability of several waste emplacement panel access drifts. The drifts were assumed to be located within a central shaft pillar, within a small pillar between adjacent panels, or at the repository perimeter. The results of analyses indicate that matrix failure is unlikely and that the extent of activation of pre-existing joints is influenced by the drift location and the initial state of stress. The results also show that several years after waste emplacement the influence of the initial State of Stress is small compared to the influence of thermally induced stresses. Regions of joint activation are seen to be most extensive around the drifts between adjacent panels. The predicted extent of such activation was small when it was assumed that the joints were vertical or near vertical. More extensive regions of activation of shallow dipping joints were noted. However, joints of such orientation are believed to occur relatively infrequently in the candidate horizon for waste emplacement and the activation of the shallow dipping joints does not necessarily lead to drift stability concerns. 3 refs., 24 figs., 7 tabs

Assessment of the long-term safety of repositories. Scientific basis

International Nuclear Information System (INIS)

Noseck, Ulrich; Becker, Dirk; Fahrenholz, Christine

2008-12-01

The project contributed to increase the scientific knowledge on the long-term safety assessment and the safety cases of a radioactive waste repository. International guidelines and more recent safety cases from other countries were evaluated. The feasibility study of the three safety indicators ''individual dose rate'', ''radiotoxicity concentration in the biosphere water'' and ''radiotoxicity flux from the geosphere'' showed that due to the independently derived corresponding reference values these indicators describe three different safety statements. The combination of the three values can give a stronger argument for the safety of the repository system. Another important methodological aspect of the safety cases is the definition and selection of scenarios, one of these the human intrusion scenario. Various human intrusion scenarios are considered in the different nations, which differ significantly with respect to type and time scale, the exposition type and exposition pathway. Further progress has been achieved in how to treat human intrusion scenarios in a German post-closure safety case. Another port of the project dealt with the impact of specific geochemical processes on the long-term safety of the repository. The impact of climate changes on the long-term safety of a radioactive waste repository in rock salt was investigated with respect to processes in the overburden and the biosphere where highest impact is expected. Sofa simplified models and only discrete climate estates have been considered

The European Repository Landscape 2008 Inventory of Digital Repositories for Research Output

CERN Document Server

Van der Graaf, Maurits

2009-01-01

It is widely acknowledged that a common knowledge base for European research is necessary. Research repositories are an important innovation to the scientific information infrastructure. In 2006, digital repositories in the 27 countries of the European we

Repository Safety Strategy: Strategy for Protecting Public Health and Safety after Closure of a Yucca Mountain Repository, Rev. 1

Energy Technology Data Exchange (ETDEWEB)

DOE

1998-01-01

The updated Strategy to Protect Public Health and Safety explains the roles that the natural and engineered systems are expected to play in achieving the objectives of a potential repository system at Yucca Mountain. These objectives are to contain the radionuclides within the waste packages for thousands of years, and to ensure that annual doses to a person living near the site will be acceptably low. This strategy maintains the key assumption of the Site Characterization Plan (DOE 1988) strategy that the potential repository level (horizon) will remain unsaturated. Thus, the strategy continues to rely on the natural attributes of the unsaturated zone for primary protection by providing a setting where waste packages assisted by other engineered barriers are expected to contain wastes for thousands of years. As in the Site Characterization Plan (DOE 1988) strategy, the natural system from the walls of the underground openings (drifts) to the human environment is expected to provide additional defense by reducing the concentrations of any radionuclides released from the waste packages. The updated Strategy to Protect Public Health and Safety is the framework for the integration of site information, repository design and assessment of postclosure performance to develop a safety case for the viability assessment and a subsequent license application. Current site information and a reference design are used to develop a quantitative assessment of performance to be compared with a performance measure. Four key attributes of an unsaturated repository system that are critical to meeting the objectives: (1) Limited water contacting the waste packages; (2) Long waste package lifetime; (3) Slow rate of release of radionuclides from the waste form; and (4) Concentration reduction during transport through engineered and natural barriers.

Office of Geologic Repositories quality assurance plan for high-level radioactive waste repositories

International Nuclear Information System (INIS)

1986-08-01

This document sets forth geologic repository program-wide quality assurance program requirements and defines management's quality assurance responsibilities for the Office of Geologic Repositories and its projects. (LM)

Virtual patient repositories--a comparative analysis.

Science.gov (United States)

Küfner, Julia; Kononowicz, Andrzej A; Hege, Inga

2014-01-01

Virtual Patients (VPs) are an important component of medical education. One way to reduce the costs for creating VPs is sharing through repositories. We conducted a literature review to identify existing repositories and analyzed the 17 included repositories in regards to the search functions and metadata they provide. Most repositories provided some metadata such as title or description, whereas other data, such as educational objectives, were less frequent. Future research could, in cooperation with the repository provider, investigate user expectations and usage patterns.

A repository of codes of ethics and technical standards in health informatics.

Science.gov (United States)

Samuel, Hamman W; Zaïane, Osmar R

2014-01-01

We present a searchable repository of codes of ethics and standards in health informatics. It is built using state-of-the-art search algorithms and technologies. The repository will be potentially beneficial for public health practitioners, researchers, and software developers in finding and comparing ethics topics of interest. Public health clinics, clinicians, and researchers can use the repository platform as a one-stop reference for various ethics codes and standards. In addition, the repository interface is built for easy navigation, fast search, and side-by-side comparative reading of documents. Our selection criteria for codes and standards are two-fold; firstly, to maintain intellectual property rights, we index only codes and standards freely available on the internet. Secondly, major international, regional, and national health informatics bodies across the globe are surveyed with the aim of understanding the landscape in this domain. We also look at prevalent technical standards in health informatics from major bodies such as the International Standards Organization (ISO) and the U. S. Food and Drug Administration (FDA). Our repository contains codes of ethics from the International Medical Informatics Association (IMIA), the iHealth Coalition (iHC), the American Health Information Management Association (AHIMA), the Australasian College of Health Informatics (ACHI), the British Computer Society (BCS), and the UK Council for Health Informatics Professions (UKCHIP), with room for adding more in the future. Our major contribution is enhancing the findability of codes and standards related to health informatics ethics by compilation and unified access through the health informatics ethics repository.

Viability Assessment of a Repository at Yucca Mountain. Volume 2: Preliminary Design Concept for the Repository and Waste Package

Energy Technology Data Exchange (ETDEWEB)

None

1998-12-01

This volume describes the major design features of the Monitored Geologic Repository. This document is not intended to provide an exhaustive, detailed description of the repository design. Rather, this document summarizes the major systems and primary elements of the design that are radiologically significant, and references the specific technical documents and design analyses wherein the details can be found. Not all portions of the design are at the same level of completeness. Highest priority has been given to assigning resources to advance the design of the Monitored Geologic Repository features that are important to radiological safety and/or waste isolation and for which there is no NRC licensing precedent. Those features that are important to radiological safety and/or waste isolation, but for which there is an NRC precedent, receive second priority. Systems and features that have no impact on radiological safety or waste isolation receive the lowest priority. This prioritization process, referred to as binning, is discussed in more detail in Section 2.3. Not every subject discussed in this volume is given equal treatment with regard to the level of detail provided. For example, less detail is provided for the surface facility design than for the subsurface and waste package designs. This different level of detail is intentional. Greater detail is provided for those functions, structures, systems, and components that play key roles with regard to protecting radiological health and safety and that are not common to existing nuclear facilities already licensed by NRC. A number of radiological subjects are not addressed in the VA, (e.g., environmental qualification of equipment). Environmental qualification of equipment and other radiological safety considerations will be addressed in the LA. Non-radiological safety considerations such as silica dust control and other occupational safety considerations are considered equally important but are not addressed in

Technology overview of mined repositories

International Nuclear Information System (INIS)

Gimera, R.; Thirumalai, K.

1982-01-01

Mined repositories present an environmentally viable option for permanent disposal of nuclear waste. This paper reviews the state-of-the-art mining technologies and identifies technological issues and developments necessary to mine a repository in basalt. The thermal loading, isolation, and retrieval requirements of a repository present unique technological challenges unknown to conventional mining practice. The technology issues and developments required in the areas of excavation, roof and ground support, equipment development, instrumentation development, and sealing are presented. Performance assessment methods must be developed to evaluate the adequacies of technologies developed to design, construct, operate, and decommission a repository. A stepwise test-and-development approach is used in the Basalt Waste Isolation Project to develop cost-effective technologies for a repository

Breast Cancer Tissue Repository

National Research Council Canada - National Science Library

Iglehart, J

1997-01-01

The Breast Tissue Repository at Duke enters its fourth year of finding. The purpose of the Repository at Duke is to provide substantial quantities of frozen tissue for explorative molecular studies...

Radioactive waste isolation in salt: peer review of the Office of Nuclear Waste Isolation's reports on preferred repository sites within the Palo Duro Basin, Texas

International Nuclear Information System (INIS)

Fenster, D.; Edgar, D.; Gonzales, S.; Domenico, P.; Harrison, W.; Engelder, T.; Tisue, M.

1984-04-01

Documents are being submitted to the Salt Repository Project Office (SRPO) of the US Department of Energy (DOE) by Battelle Memorial Institute's Office of Nuclear Waste Isolation (ONWI) to satisfy milestones of the Salt Repository Project of the Civilian Radioactive Waste Management Program. Some of these documents are being reviewed by multidisciplinary groups of peers to ensure DOE of their adequacy and credibility. Adequacy of documents refers to their ability to meet the standards of the US Nuclear Regulatory Commission, as enunciated in 10 CFR 60, and the requirements of the National Environmental Policy Act and the Nuclear Waste Policy Act of 1982. Credibility of documents refers to the validity of the assumptions, methods, and conclusions, as well as to the completeness of coverage. This report summarizes Argonne's review of ONWI's two-volume draft report entitled Identification of Preferred Sites within the Palo Duro Basin: Vol. 1 - Palo Duro Location A, and Vol. 2 - Palo Duro Location B, dated January 1984. Argonne was requested by DOE to review these documents on January 17 and 24, 1984 (see App. A). The review procedure involved obtaining written comments on the reports from three members of Argonne's core peer review staff and three extramural experts in related research areas. The peer review panel met at Argonne on February 6, 1984, and reviewer comments were integrated into this report by the review session chairman, with the assistance of Argonne's core peer review staff. All of the peer review panelists concurred in the way in which their comments were represented in this report (see App. B). A letter report and a draft of this report were sent to SRPO on February 10, 1984, and April 17, 1984, respectively. 5 references

Hydrological and hydrogeological effects of an open repository in Forsmark. Final MIKE SHE flow modelling results for the Environmental Impact Assessment

International Nuclear Information System (INIS)

Maartensson, Erik; Gustafsson, Lars-Goeran

2010-07-01

This report presents methodology and modelling results concerning a deep-rock repository for spent nuclear fuel in Forsmark. Specifically, the modelling tools MIKE SHE, MIKE 11 and MOUSE are used to quantify the groundwater inflow to the repository and associated hydrological and hydrogeological effects during the construction and operation phases. The modelling results presented in the report provide input to the Environmental Impact Assessment (EIA) that will be part of a permit application according to the Environmental Code. Based on an existing MIKE SHE model for Forsmark, the first step of the modelling process was to implement an updated hydrogeological model of the bedrock and to increase the vertical and horizontal extents of the model domain. Other model updates involve the vegetation classification, and implementation of SFR (final repository for short-lived radioactive waste) and the subsurface drainage system at the nearby nuclear power plant. The updated model was calibrated using measured data on groundwater levels in the Quaternary deposits and the bedrock, water levels in lakes, and stream discharges. The calibrated model was then used for simulation of undisturbed conditions (i.e. without the repository) as a reference for modelling results obtained for disturbed conditions (with the repository). The modelling results for undisturbed conditions that are presented in the report closely resemble those of the final MIKE SHE site descriptive modelling (SDM-Site Forsmark). The repository layout was implemented as pipe links (segments) in the modelling tool MOUSE, and the implemented layout was used for the modelling of disturbed conditions. The study uses an updated and verified MIKE SHE-MOUSE coupling routine that is specifically adapted for calculation of groundwater inflow to grouted rock tunnels. The vertical shafts of the repository are implemented in the form of MIKE SHE grid cells with atmospheric pressure. Modelling results for disturbed

Hydrological and hydrogeological effects of an open repository in Forsmark. Final MIKE SHE flow modelling results for the Environmental Impact Assessment

Energy Technology Data Exchange (ETDEWEB)

Maartensson, Erik; Gustafsson, Lars-Goeran (DHI Sverige AB (Sweden))

2010-07-15

This report presents methodology and modelling results concerning a deep-rock repository for spent nuclear fuel in Forsmark. Specifically, the modelling tools MIKE SHE, MIKE 11 and MOUSE are used to quantify the groundwater inflow to the repository and associated hydrological and hydrogeological effects during the construction and operation phases. The modelling results presented in the report provide input to the Environmental Impact Assessment (EIA) that will be part of a permit application according to the Environmental Code. Based on an existing MIKE SHE model for Forsmark, the first step of the modelling process was to implement an updated hydrogeological model of the bedrock and to increase the vertical and horizontal extents of the model domain. Other model updates involve the vegetation classification, and implementation of SFR (final repository for short-lived radioactive waste) and the subsurface drainage system at the nearby nuclear power plant. The updated model was calibrated using measured data on groundwater levels in the Quaternary deposits and the bedrock, water levels in lakes, and stream discharges. The calibrated model was then used for simulation of undisturbed conditions (i.e. without the repository) as a reference for modelling results obtained for disturbed conditions (with the repository). The modelling results for undisturbed conditions that are presented in the report closely resemble those of the final MIKE SHE site descriptive modelling (SDM-Site Forsmark). The repository layout was implemented as pipe links (segments) in the modelling tool MOUSE, and the implemented layout was used for the modelling of disturbed conditions. The study uses an updated and verified MIKE SHE-MOUSE coupling routine that is specifically adapted for calculation of groundwater inflow to grouted rock tunnels. The vertical shafts of the repository are implemented in the form of MIKE SHE grid cells with atmospheric pressure. Modelling results for disturbed

Building a semantic web-based metadata repository for facilitating detailed clinical modeling in cancer genome studies.

Science.gov (United States)

Sharma, Deepak K; Solbrig, Harold R; Tao, Cui; Weng, Chunhua; Chute, Christopher G; Jiang, Guoqian

2017-06-05

Detailed Clinical Models (DCMs) have been regarded as the basis for retaining computable meaning when data are exchanged between heterogeneous computer systems. To better support clinical cancer data capturing and reporting, there is an emerging need to develop informatics solutions for standards-based clinical models in cancer study domains. The objective of the study is to develop and evaluate a cancer genome study metadata management system that serves as a key infrastructure in supporting clinical information modeling in cancer genome study domains. We leveraged a Semantic Web-based metadata repository enhanced with both ISO11179 metadata standard and Clinical Information Modeling Initiative (CIMI) Reference Model. We used the common data elements (CDEs) defined in The Cancer Genome Atlas (TCGA) data dictionary, and extracted the metadata of the CDEs using the NCI Cancer Data Standards Repository (caDSR) CDE dataset rendered in the Resource Description Framework (RDF). The ITEM/ITEM_GROUP pattern defined in the latest CIMI Reference Model is used to represent reusable model elements (mini-Archetypes). We produced a metadata repository with 38 clinical cancer genome study domains, comprising a rich collection of mini-Archetype pattern instances. We performed a case study of the domain "clinical pharmaceutical" in the TCGA data dictionary and demonstrated enriched data elements in the metadata repository are very useful in support of building detailed clinical models. Our informatics approach leveraging Semantic Web technologies provides an effective way to build a CIMI-compliant metadata repository that would facilitate the detailed clinical modeling to support use cases beyond TCGA in clinical cancer study domains.

Phenomenological description reference concept (Spent Fuel - Copper - Iron - Bentonite - Granite)

International Nuclear Information System (INIS)

Lehikoinen, J.; Nordman, H.

2008-12-01

This report gives a broad overview of the salient processes and associated time frames and uncertainties pertaining to the long-term normal evolution of the near-field of a deep repository of the KBS-3V type. By normal evolution, reference is made to the description of the evolution of a disposal system subject to the assumption that all the spent fuel canisters remain intact following emplacement and repository closure for at least the design corrosion lifetime of the canister overpack in the expected repository conditions. In this connection, the effects of future glaciations, canister manufacturing defects and small-scale tectonic activity are briefly touched upon. The roles of the different repository near-field barriers in providing safety are briefly noted. The description of the normal evolution of a KBS-3V-type repository near-field conditions external to the unbreached spent fuel canister has been realized in terms of processes rather than timescales. Separate chapters have been devoted to the thermal, hydraulic, mechanical and chemical/biological evolution of the repository system, with due attention to some of the couplings between them. (orig.)

Construction of First Phase of Spent Fuel Repository in Finland: Lessons Learned and Success Factors

International Nuclear Information System (INIS)

Varjoranta, T.; Paltemaa, R.

2015-01-01

The Finnish nuclear legislation defines spent fuel as nuclear waste and requires that it has to be disposed of in the Finnish bedrock. Over 30 years of systematic R&D has been carried out to develop the repository concept, site selection, technologies, safety assessment and the regulatory approach. Activities are based on the Finnish Government’s long term strategies since 1983 and the public acceptance at local, Governmental and Parliament levels, approved and documented in the legal “Decision in Principle” (DiP) in 2000 to locate the repository at Olkiluoto. The DiP provided authorization to construct the first phase of the repository to the depth of the planned disposal. The construction of the 1 st phase of the repository started 2004 and has now reached the depth of 407 m. This paper identifies and discusses lessons learned and key success factors of the progress made. (author)

Estimation of expenses for low and intermediate level radioactive waste repository project in Croatia up to site license acquisition

International Nuclear Information System (INIS)

Schaller, A.; Lokner, V.; Subasic, D.

2003-01-01

The expenses needed for development of low- and intermediate level radioactive waste (LILW) repository project in Croatia include: (a) preliminary activities, (b) preparatory activities, and (c) preparing of environmental impact study. The first group of expenses are referring to the project leading activities, project plan updating, build-up of required infrastructure, preparing of licensing documentation, site investigations, data acquisition programme, pre-operational radio-ecological monitoring, modelling, safety analysis (first iteration) and public related activities. Preparatory activities are referring to purchasing of land for repository and preparatory activities for carrying out of on-site investigations, while third group of expenses are related to preparation and validation of Environmental impact study. It was found out that about 50 % of total expenses refer to build-up of infrastructure. Additional 25 % finances are related to radio-ecological monitoring, site investigations and development of calculations and models, while remaining 25 % of total estimated sum is expected to be spent for repository safety assessment, public relations, purchasing and preparing the on-site terrain for construction, etc. It was calculated 607 EUR per m3 of LILW to be needed up to site license acquisition. According to the world-wide practice, by extrapolating of additional expenses necessary for construction of the repository and acquisition of operational license, it comes out the cost of 1.723 EUR per m3 of LILW for shallow-ground and 2.412 EUR per m3 of LILW for tunnel repository. The estimated expenses for Croatia are within the span of expenses for the same purpose in the countries considered. Expected duration of the project performance up to acquisition of the site license is 4 years and 3 months. (author)

A geologic scenario for catastrophic failure of the Yucca Mountain Nuclear Waste Repository, Nevada

International Nuclear Information System (INIS)

McMackin, M.R.

1993-01-01

A plausible combination of geologic factors leading to failure can be hypothesized for the Yucca Mountain Nuclear Waste Repository. The scenarios is constructed using elementary fault mechanics combined with geologic observations of exhumed faults and published information describing the repository site. The proposed repository site is located in the Basin and Range Province, a region of active crustal deformation demonstrated by widespread seismicity. The Yucca Mountain area has been characterized as tectonically quiet, which in the context of active crustal deformation may indicate the accumulation of the stresses approaching the levels required for fault slip, essentially stick-slip faulting. Simultaneously, dissolution of carbonate rocks in underlying karst aquifers is lowering the bulk strength of the rock that supports the repository site. Rising levels of hydrostatic stress concurrent with a climatically-driven rise in the water table could trigger faulting by decreasing the effective normal stress that currently retards fault slip. Water expelled from collapsing caverns in the underlying carbonate aquifer could migrate upward with sufficient pressure to open existing fractures or create new fractures by hydrofracturing. Water migrating through fractures could reach the repository in sufficient volume to react with heated rock and waste perhaps creating steam explosions that would further enhance fracture permeability. Closure of conduits in the underlying carbonate aquifer could lead to the elevation of the saturated zone above the level of the repository resulting in sustained saturation of radioactive waste in the repository and contamination of through-flowing groundwater

The study on safety facility criteria for radioactive waste repository

International Nuclear Information System (INIS)

Lee, S. H.; Choi, M. H.; Han, S. H. and others

1992-12-01

The radioactive waste repository are necessary to install the engineered safety systems to secure the safety for operation of the repository in the event of fire and earthquake. Since the development of safety facility criteria requires a thorough understanding about the characteristics of the engineered safety systems, we should investigate by means of literature survey and visit SKB. In particular, definition, composition of the systems, functional requirement of the systems, engineered safety systems of foreign countries, system design, operation and maintenance requirement should be investigated : fire protection system, ventilation system, drainage system, I and C system, electric system, radiation monitoring system. This proposed criteria consist of purpose, scope of application, ventilation system, fire protection system, drainage system, electric system and this proposed criteria can be applied as a basic reference for the final criteria

Selected, annotated bibliography of studies relevant to the isolation of nuclear wastes. [705 references

Energy Technology Data Exchange (ETDEWEB)

Hyder, L.K.; Fore, C.S.; Vaughan, N.D.; Faust, R.A.

1980-09-01

This annotated bibliography of 705 references represents the first in a series to be published by the Ecological Sciences Information Center containing scientific, technical, economic, and regulatory information relevant to nuclear waste isolation. Most references discuss deep geologic disposal, with fewer studies of deep seabed disposal; space disposal is also included. The publication covers both domestic and foreign literature for the period 1954 to 1980. Major chapters selected are Chemical and Physical Aspects; Container Design and Performance; Disposal Site; Envirnmental Transport; General Studies and Reviews; Geology, Hydrology and Site Resources; Regulatory and Economic Aspects; Repository Design and Engineering; Transportation Technology; Waste Production; and Waste Treatment. Specialized data fields have been incorporated to improve the ease and accuracy of locating pertinent references. Specific radionuclides for which data are presented are listed in the Measured Radionuclides field, and specific parameters which affect the migration of these radionuclides are presented in the Measured Parameters field. The references within each chapter are arranged alphabetically by leading author, corporate affiliation, or title of the document. When the author is not given, the corporate affiliation appears first. If these two levels of authorship are not given, the title of the document is used as the identifying level. Indexes are provided for author(s), keywords, subject category, title, geographic location, measured parameters, measured radionuclides, and publication description.

Presentation of safety after closure of the repository for spent nuclear fuel. Main report of the project SR-Site. Part III

International Nuclear Information System (INIS)

2011-01-01

The purpose of the safety assessment SR-Site is to investigate whether a safe repository for spent nuclear fuel by KBS-3 type can be constructed at Forsmark in Oesthammar in Sweden. The location of the Forsmark has been selected based on results of several surveys from surface conditions at depth in Forsmark and in Laxemar in Oskarshamn. The choice of location is not justified in SR-Site Report, but in other attachments to SKB's permit applications. SR-Site Report is an important part of SKB's permit applications to construct and operate a repository for spent nuclear fuel at Forsmark in Oesthammar. The purpose of the report in the applications is to show that a repository at Forsmark is safe after closure

Presentation of safety after closure of the repository for spent nuclear fuel. Main report of the project SR-Site. Part I

International Nuclear Information System (INIS)

2011-01-01

The purpose of the safety assessment SR-Site is to investigate whether a safe repository for spent nuclear fuel by KBS-3 type can be constructed at Forsmark in Oesthammar in Sweden. The location of the Forsmark has been selected based on results of several surveys from surface conditions at depth in Forsmark and in Laxemar in Oskarshamn. The choice of location is not justified in SR-Site Report, but in other attachments to SKB's permit applications. SR-Site Report is an important part of SKB's permit applications to construct and operate a repository for spent nuclear fuel at Forsmark in Oesthammar. The purpose of the report in the applications is to show that a repository at Forsmark is safe after closure

Studies relating to human intrusion into a repository. Report pertaining to work package 11. Preliminary safety case of the Gorleben site (VSG)

Energy Technology Data Exchange (ETDEWEB)

Beuth, Thomas; Buhmann, Dieter; Fischer-Appelt, Klaus; Moenig, Joerg; Ruebel, Andre; Wolf, Jens [Gesellschaft fuer Anlagen- und Reaktorsicherheit mbH (GRS), Koeln (Germany); Bollingerfehr, Wilhelm; Filbert, Wolfgang [DBE Technology GmbH, Peine (Germany); Charlier, Frank [international nuclear safety engineering gmbh (nse), Aachen (Germany); Baltes, Bruno

2014-10-15

The question of the long-term safety of a repository system is inseparably linked with the intensive technical examination of the possible future evolution of the site and the repository system e. g. as a result of climatic, geologic, waste-related and repository-related processes. Here, the possible evolutions to be considered are those that have the potential to have a negative impact on the intended, furthest-possible, immediate, and lasting isolation of the radioactive waste in a defined area around the underground workings of the repository mine in salt rock, which is referred to as the containment-providing rock zone (CPRZ).

Development of local partnership for siting of LILW repository in Slovenia

International Nuclear Information System (INIS)

Kralj, Metka; Zeleznik, Nadja

2007-01-01

Available in abstract form only. Full text of publication follows: Slovenia has only temporary storage facilities for radioactive waste. According to the legislation, a permanent LILW repository site should be authorized by 2008, and the repository has to acquire the operating licence by 2013. In 2006, ARAO, the general public and three municipalities established local partnerships in order to increase public acceptability of the LILW repository. Civil initiative groups opposed to the siting appeared in all three local communities. In one case they forced the municipality to withdraw, in one case they changed the siting location, and in one case they were integrated to local partnership. In the municipality of Krsko, the program of local partnership was publicly discussed. There is an NPP in Krsko, so the local partnership also demanded to discuss the power plant issues. Thematic committees were established that worked separately. They also discussed the issues of the spatial plan for the repository. In the municipality of Brezice, a steering committee was established to promote local partnership activities and organization of thematic committees. There was only one active thematic committee, but many activities for the general public were organised. In the municipality of Sevnica, the local partnership was soon cancelled. (authors)

Analytical evaluation of the radionuclide concentration through the aquifer for the Abadia de Goias Repository

International Nuclear Information System (INIS)

Alves, Antonio Sergio de Martin

1999-01-01

In this paper the radionuclide concentration though the aquifer has been determined by an analytical process considering that the radionuclide migration is influenced by two kinds of radionuclides releases from the repository during an overflow. In the first release it is assumed that when the radionuclides reach the aquifer there is no contamination in it and the release rate is a constant. For this case it is utilized the model of Reference. For the subsequent releases there will be a contamination in the aquifer provenient from the former releases; it is considered that the subsequent releases are a function of the time which, for the Abadia de Goias Repository, was determined in the Reference. The Laplace transform Method has been utilized to solve the Radionuclide Migration Transport Equation in the aquifer region for the subsequent releases and the resulting function is expressed in terms of exponential and complementary error functions. The improvement in the calculation model, presented in this paper, can be used in the safety analysis of repositories, contributing thus in the nuclear waste management field and particularly, being connecting also to the environmental protection concern. (author)

Economic implications of locating a nuclear waste repository in Texas. Hearing before the Subcommittee on Nuclear Regulation of the Committee on Environment and Public Works, United States Senate, Ninety-Ninth Congress, First Session, February 11, 1985, Hereford, TX

International Nuclear Information System (INIS)

Anon.

1985-01-01

Ten witnesses representing Texas industries and agriculture spoke at a field hearing in Hereford, Texas on the selection of Deaf Smith County as one of the three potential repository sites for spent fuel and high-level radioactive wastes. Safety and the potential for ground water contamination were major arguments of the opponents to the location. DOE spokesman William Purcell advised that no material will be placed in the repository until the turn of the century and then after a lengthy public licensing procedure. Other concerns were the socio-economic impacts on the surrounding area and the possible damage to agriculture if either soil or water contamination should occur. Additional statements submitted for the record follow the testimony

Radioactive waste isolation in salt: Peer review of the Fluor Technology, Inc., report and position paper concerning waste emplacement mode and its effect on repository conceptual design

International Nuclear Information System (INIS)

Hambley, D.F.; Russell, J.E.; Whitfield, R.G.

1987-02-01

Recommendations for revising the Fluor Technology, Inc., draft position paper entitled Evaluation of Waste Emplacement Mode and the final report entitled Waste Package/Repository Impact Study include: reevaluate the relative rankings for the various emplacement modes; delete the following want objectives: maximize ability to locate the package horizon because sufficient flexibility exists to locate rooms in the relatively clean San Andres Unit 4 Salt and maximize far-field geologic integrity during retrieval because by definition the far field will be unaffected by thermal and stress perturbations caused by remining; give greater emphasis to want objectives regarding cost and use of present technology; delete the following statements from pages 1-1 and 1-2 of the draft position paper: ''No thought or study was given to the impacts of this configuration [vertical emplacement] on repository construction or short and long-term performance of the site'' and ''Subsequent salt repository designs adopted the vertical emplacement configuration as the accepted method without further evaluation.''; delete App. E and lines 8-17 of page 1-4 of the draft position paper because they are inappropriate; adopt a formal decision-analysis procedure for the 17 identified emplacement modes; revise App. F of the impact study to more accurately reflect current technology; consider designing the underground layout to take advantage of stress-relief techniques; consider eliminating reference to fuel assemblies <10 yr ''out-of-reactor''; model the temperature distribution, assuming that the repository is constructed in an infinitely large salt body; state that the results of creep analyses must be considered tentative until they can be validated by in situ measurements; and reevaluate the peak radial stresses on the waste package so that the calculated stress conditions more closely approximate expected in situ conditions

INSTITUTIONAL REPOSITORY: EMPLOYMENT IN EDUCATION

Directory of Open Access Journals (Sweden)

Vasyl P. Oleksyuk

2012-11-01

Full Text Available The article investigated the concept of «institutional repository» and determined the aspects of institutional repositories in higher education. Institutional Repositories are information systems that allow preserving, storing and disseminating scientific knowledge produced in higher education and scientific research institutions. This study presented the main aspects using institutional repositories in educational process (such as storage of scientific and educational information, means of organization activity of students, object of studying. This article produced the structure of communities and collections of the institutional. It is described the experience of implementing of DSpace in the learning process.

Geochemical homogeneity of tuffs at the potential repository level, Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Peterman, Zell E.; Cloke, Paul

2001-01-01

In a potential high-level radioactive waste repository at Yucca Mountain, Nevada, radioactive waste and canisters, drip shields protecting the waste from seepage and from rock falls, the backfill and invert material of crushed rock, the host rock, and water and gases contained within pores and fractures in the host rock together would form a complex system commonly referred to as the near-field geochemical environment. Materials introduced into the rock mass with the waste that are designed to prolong containment collectively are referred to as the Engineered Barrier System, and the host rock and its contained water and gases compose the natural system. The interaction of these component parts under highly perturbed conditions including temperatures well above natural ambient temperatures will need to be understood to assess the performance of the potential repository for long-term containment of nuclear waste. The geochemistry and mineralogy of the rock mass hosting the emplacement drifts must be known in order to assess the role of the natural system in the near-field environment. Emplacement drifts in a potential repository at Yucca Mountain would be constructed in the phenocryst-poor member of the Topopah Spring Tuff which is composed of both lithophysal and nonlithophysal zones. The chemical composition of the phenocryst-poor member has been characterized by numerous chemical analyses of outcrop samples and of core samples obtained by surface-based drilling. Those analyses have shown that the phenocryst-poor member of the Topopah Spring Tuff is remarkably uniform in composition both vertically and laterally. To verify this geochemical uniformity and to provide rock analyses of samples obtained directly from the potential repository block, major and trace elements were analyzed in core samples obtained from drill holes in the cross drift, which was driven to provide direct access to the rock mass where emplacement drifts would be constructed

Contribution to and Use of Online Knowledge Repositories: The Role of Governance Mechanisms

Science.gov (United States)

Kayhan, Varol O.

2010-01-01

Drawing upon the concept of governance, this dissertation refers to the two most commonly employed mechanisms that ensure high quality knowledge in electronic repositories as expert-governance and community-governance. In three related but distinct essays, the dissertation examines the governance concept, and investigates contributing knowledge to…

Trust in Digital Repositories

Directory of Open Access Journals (Sweden)

Elizabeth Yakel

2013-06-01

Full Text Available ISO 16363:2012, Space Data and Information Transfer Systems - Audit and Certification of Trustworthy Digital Repositories (ISO TRAC, outlines actions a repository can take to be considered trustworthy, but research examining whether the repository’s designated community of users associates such actions with trustworthiness has been limited. Drawing from this ISO document and the management and information systems literatures, this paper discusses findings from interviews with 66 archaeologists and quantitative social scientists. We found similarities and differences across the disciplines and among the social scientists. Both disciplinary communities associated trust with a repository’s transparency. However, archaeologists mentioned guarantees of preservation and sustainability more frequently than the social scientists, who talked about institutional reputation. Repository processes were also linked to trust, with archaeologists more frequently citing metadata issues and social scientists discussing data selection and cleaning processes. Among the social scientists, novices mentioned the influence of colleagues on their trust in repositories almost twice as much as the experts. We discuss the implications our findings have for identifying trustworthy repositories and how they extend the models presented in the management and information systems literatures.

General conceptual design study for a high level radioactive waste repository in a granite formation. Volume 1

International Nuclear Information System (INIS)

1982-01-01

The object of the general conceptual design study for a repository for disposal of radioactive waste in a granite formation is to ensure that the technology available in 1980 is suitable for the construction of such a repository. The recommended techniques and equipment are suitable for construction of a repository, located at a depth of 1000 metres in a granite batholith, with a capacity of 30,000 AVM canisters, cooled for 30 years on the surface, at a rate of 1,000 canisters per year. The structure consists of six access shafts of 4 and 5 metres diameter, drilled from the surface by the big-hole method, serving a network of 82 parallel galleries, 2,300 metres long, mined by conventional blasting. Shafts 100 metres deep are drilled in the floor of each gallery (74 shafts per gallery), each shaft accommodating five canisters. This represents an aggregate gallery length of 200 kilometres and an aggregate shaft length of 600 kilometres. The cost of the operation is 1.3% of the cost (ex-works) of the energy produced by the power stations generating the waste. Construction, operation and final abandonment will take 81 years. The sensitivity study of the design showed, by varying certain parameters, that location of the repository at a depth of 500 metres is not recommended and that the area covered by the repository of 4 km 2 is halved if the canisters are first cooled for 100 years

Desiderata for healthcare integrated data repositories based on architectural comparison of three public repositories.

Science.gov (United States)

Huser, Vojtech; Cimino, James J

2013-01-01

Integrated data repositories (IDRs) are indispensable tools for numerous biomedical research studies. We compare three large IDRs (Informatics for Integrating Biology and the Bedside (i2b2), HMO Research Network's Virtual Data Warehouse (VDW) and Observational Medical Outcomes Partnership (OMOP) repository) in order to identify common architectural features that enable efficient storage and organization of large amounts of clinical data. We define three high-level classes of underlying data storage models and we analyze each repository using this classification. We look at how a set of sample facts is represented in each repository and conclude with a list of desiderata for IDRs that deal with the information storage model, terminology model, data integration and value-sets management.

Process mining software repositories

NARCIS (Netherlands)

Poncin, W.; Serebrenik, A.; Brand, van den M.G.J.

2011-01-01

Software developers' activities are in general recorded in software repositories such as version control systems, bug trackers and mail archives. While abundant information is usually present in such repositories, successful information extraction is often challenged by the necessity to

Review of geotechnical measurement techniques for a nuclear waste repository in bedded salt

International Nuclear Information System (INIS)

1979-12-01

This report presents a description of geotechnical measurement techniques that can provide the data necessary for safe development - i.e., location, design, construction, operation, decommissioning and abandonment - of a radioactive waste repository in bedded salt. Geotechnical data obtained by a diversity of measurement techniques are required during all phases of respository evolution. The techniques discussed in this report are grouped in the following categories: geologic, geophysical and geodetic; rock mechanics; hydrologic, hydrogeologic and water quality; and thermal. The major contribution of the report is the presentation of extensive tables that provide a review of available measurement techniques for each of these categories. The techniques are also discussed in the text to the extent necessary to describe the measurements and associated instruments, and to evaluate the applicability or limitations of the method. More detailed discussions of thermal phenomena, creep laws and geophysical methods are contained in the appendices; references to detailed explanations of measurement techniques and instrumentation are inluded throughout the report

Review of geotechnical measurement techniques for a nuclear waste repository in bedded salt

Energy Technology Data Exchange (ETDEWEB)

1979-12-01

This report presents a description of geotechnical measurement techniques that can provide the data necessary for safe development - i.e., location, design, construction, operation, decommissioning and abandonment - of a radioactive waste repository in bedded salt. Geotechnical data obtained by a diversity of measurement techniques are required during all phases of respository evolution. The techniques discussed in this report are grouped in the following categories: geologic, geophysical and geodetic; rock mechanics; hydrologic, hydrogeologic and water quality; and thermal. The major contribution of the report is the presentation of extensive tables that provide a review of available measurement techniques for each of these categories. The techniques are also discussed in the text to the extent necessary to describe the measurements and associated instruments, and to evaluate the applicability or limitations of the method. More detailed discussions of thermal phenomena, creep laws and geophysical methods are contained in the appendices; references to detailed explanations of measurement techniques and instrumentation are inluded throughout the report.

Engineering studies: high-level radioactive waste repositories task 3 - review of underground handling and emplacement. 1. Executive summary

Energy Technology Data Exchange (ETDEWEB)

1981-02-01

The report reviews proposals for transport, handling and emplacement of high-level radioactive waste in an underground repository with particular reference to: waste block size and configuration; self-shielded or partially-shielded block; stages of disposal; transport by road/rail to repository site; handling techniques within repository; emplacement in vertical holes or horizontal tunnels; repository access by adit, incline or shaft; conventional and radiological safety; costs; and major areas of uncertainty requiring research or development. In carrying out this programme due attention was given to work already carried out both in the U.K. and overseas and where appropriate comparisons with this work have been made to substantiate and explain the observations made in this report. The examination and use of this previous work however has been confined to those proposals which were considered capable of meeting the basic design criterion for a U.K. based repository, that the maximum temperature achieved by the host rock should not exceed 100/sup 0/C.

The SocioEconomic analysis of repository siting (SEARS): Guide to data base preparation: Final draft

International Nuclear Information System (INIS)

Hamm, R.R.; Murdock, S.H.; Leistritz, F.L.; Kiel, B.; Parpia, B.

1984-11-01

This guide describes the data bases in the SocioEconomic Analysis of Repository Siting (SEARS) modeling system. This model is a user-interactive, computerized model for projecting the economic, demographic, public service, and fiscal impacts of repository siting. This guide provides a description of the data bases, sources of data, data formats, and preprocessing programs for adapting and implementing the SEARS system and is seen as an essential reference for technical users of the model. It should be used in conjunction with reports describing the model's features and characteristics. 95 refs., 3 tabs

Hydrogeological modelling for assessment of radionuclide release scenarios for the repository system 2012

Energy Technology Data Exchange (ETDEWEB)

Hartley, L.; Hoek, J.; Swan, D.; Appleyard, P.; Baxter, S.; Roberts, D.; Simpson, T. [AMEC (United Kingdom)

2013-07-15

Posiva Oy is responsible for implementing the programme for geological disposal of spent nuclear fuel produced by its owners Teollisuuden Voima Oyj (TVO) and Fortum Power and Heat Oy in Finland. Olkiluoto in Eurajoki has been selected as the primary site for the repository, subject to further detailed investigation which is currently focused on the construction of an underground rock characterisation and research facility (the ONKALO). An essential part of the assessment of long-term safety of a repository is the analysis of groundwater flow since it is the only means of transport of radionuclides to the biosphere (besides human intrusion). The analysis of long-term safety for a KBS-3 concept requires as input a description of details of the groundwater flow around and through components of the engineered barrier system as well as details of the groundwater pathway to the biosphere during the current temperate climate period, as well as indications of behaviour under future climate periods such as glacial conditions. This report describes the groundwater flow modelling study performed to provide some of the necessary inputs required by Safety Assessment (i.e. radionuclide transport analysis). Underlying this study is the understanding of the site developed during the site investigations as summarised in the site descriptive model (SDM), and in particular the description of Olkiluoto Hydrogeological DFN model (Hydro-DFN). The main focus of this study is the temperate climate period, i.e. the evolution over the next 10,000 years, but the hydrogeological situation under various glacial climate conditions is also evaluated. Primary outputs of the study are repository performance measures relating to: the distributions of groundwater flow around the deposition holes; deposition tunnels and through the EDZ; flow-related transport resistance along groundwater pathways from the repository to the surface; and their the exit locations. Other analyses consider the

Hydrogeological modelling for assessment of radionuclide release scenarios for the repository system 2012

International Nuclear Information System (INIS)

Hartley, L.; Hoek, J.; Swan, D.; Appleyard, P.; Baxter, S.; Roberts, D.; Simpson, T.

2013-07-01

Posiva Oy is responsible for implementing the programme for geological disposal of spent nuclear fuel produced by its owners Teollisuuden Voima Oyj (TVO) and Fortum Power and Heat Oy in Finland. Olkiluoto in Eurajoki has been selected as the primary site for the repository, subject to further detailed investigation which is currently focused on the construction of an underground rock characterisation and research facility (the ONKALO). An essential part of the assessment of long-term safety of a repository is the analysis of groundwater flow since it is the only means of transport of radionuclides to the biosphere (besides human intrusion). The analysis of long-term safety for a KBS-3 concept requires as input a description of details of the groundwater flow around and through components of the engineered barrier system as well as details of the groundwater pathway to the biosphere during the current temperate climate period, as well as indications of behaviour under future climate periods such as glacial conditions. This report describes the groundwater flow modelling study performed to provide some of the necessary inputs required by Safety Assessment (i.e. radionuclide transport analysis). Underlying this study is the understanding of the site developed during the site investigations as summarised in the site descriptive model (SDM), and in particular the description of Olkiluoto Hydrogeological DFN model (Hydro-DFN). The main focus of this study is the temperate climate period, i.e. the evolution over the next 10,000 years, but the hydrogeological situation under various glacial climate conditions is also evaluated. Primary outputs of the study are repository performance measures relating to: the distributions of groundwater flow around the deposition holes; deposition tunnels and through the EDZ; flow-related transport resistance along groundwater pathways from the repository to the surface; and their the exit locations. Other analyses consider the

Psycho-social effects of a repository for spent nuclear fuels. Literature review and interviews with inhabitants of Uppsala

International Nuclear Information System (INIS)

Brostroem, L.; Kessling, A.; Kraft, G.; Sjoeberg, L.

2002-01-01

This report is a complement to the studies of the communities of Tierp, Aelvkarleby and Oesthammar as candidates for localization of a repository for spent nuclear fuels. In the first part, a study is presented of published literature in the area of psycho-social effects of building large-scale plants. In the second part interviews are reported with people living in, or with other connections with, Uppsala, of their reactions on a location of the repository in the northern part of the county of Uppland and how they believe the repository would affect the local population, the tourism and local economy

Project Alternative Systems Study - PASS. Analysis of performance and long-term safety of repository concepts

International Nuclear Information System (INIS)

Birgersson, L.; Skagius, K.; Wiborgh, M.; Widen, H.

1992-09-01

This study is part of the Project on Alternative Systems Study, PASS, with the overall aim to perform a technical/economical ranking of alternative repository concepts and canisters for the final storage of spent nuclear fuel. The comparison should in the first stage separately assess technology in construction and operation, long-term performance and safety, and costs. Three of the repository concepts are assumed to be located at a depth of approximately 500 m in the host rock, KBS-3, Very Long Holes (VLH) and Medium Long Holes (MLH). In the KBS-3 concept the canisters are deposited in vertical deposition holes in a system of parallel storage tunnels. In the VLH concept larger canisters are deposited in long horizontal tunnels. The MLH concept, is an evolution of the two other concepts, with KBS-3 type canisters deposited in horizontal tunnels. Smaller canisters are to be deposited in deep bore holes at a depth between 2000 to 4000 m in the Very Deep Holes (VDH) concept. In all concepts the canisters will be surrounded by a bentonite buffer. The aim of the present study is to analyze and compare the performance and long-term safety of the repository concepts. Only a qualitative comparison of the concepts is made as no calculations of radionuclide releases or dose to man have been performed. The ranking of the repository concepts was carried out by comparing the VDH, VLH and MLH concept with the KBS-3 concept. The performance and long-term safety of the repositories located at 500 m level will be based on a multiple barrier system and the predictions for the concepts will involve similar uncertainties. (54 refs.)

48 CFR 227.7108 - Contractor data repositories.

Science.gov (United States)

2010-10-01

... repositories. 227.7108 Section 227.7108 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS... Technical Data 227.7108 Contractor data repositories. (a) Contractor data repositories may be established when permitted by agency procedures. The contractual instrument establishing the data repository must...

Site investigations for repositories for solid radioactive wastes in deep continental geological formations

International Nuclear Information System (INIS)

1982-01-01

This report reviews the earth-science investigations and associated scientific studies that may be needed to select a repository site and confirm that its characteristics are such that it will provide a safe confinement for solidified high-level and alpha-bearing and certain other solid radioactive wastes. Site investigations, as used in this report, cover earth sciences and associated safety analyses. Other site-investigation activities are identified but not otherwise considered here. The repositories under consideration are those consisting of mined cavities in deep continental rocks for accepting wastes in the solid and packaged form. The term deep as used in this report is used solely to emphasize the distinction between the repositories discussed in this report and those for shallow-ground disposal. In general, depths under consideration here are greater than 200 metres. The term continental refers to those geological formations that occur either beneath present-day land masses and adjoining islands or beneath the shallow seas. One of the objectives of site investigations is to collect the site-specific data necessary for the different evaluations, such as modelling required to assess the long-term safety of an underground repository

Transient boundary conditions in the frame of THM-processes at nuclear waste repositories

Directory of Open Access Journals (Sweden)

Schanz Tom

2016-01-01

Full Text Available In nuclear waste repositories, initially unsaturated buffer is subjected to constant heat emitted by waste canister in conjunction with peripheral hydration through water from host rock. The transient hydration process can be potraied as transformation of initial heterogeneity towards homogeneity as final stage. In this context, this paper addresses the key issue of hydro mechanical behaviour of compacted buffer in context of clay microstructure and its evolution under repository relevant loading paths and material heterogeneity. This paper also introduces a unique column experiment facility available at Ruhr Universität Bochum, Germany. The facility has been designed as a forerunner of field scale testing program to simulate the transient hydration process of compacted buffer as per German reference disposal concept. The device is unique in terms of having proficiency to capture the transient material response under various possible repository relevant loading paths with higher precision level by monitor the key parameters like temperature, total suction, water content and axial & radial swelling pressure at three different sections along the length of compacted soil sample. In general, a larger spectrum of loading paths/scenarios, which may arise in the nuclear repository, can be covered precisely with existing device.

Site investigations for repositories for solid radioactive wastes in deep continental geological formations

Energy Technology Data Exchange (ETDEWEB)

1982-01-01

This report reviews the earth-science investigations and associated scientific studies that may be needed to select a repository site and confirm that its characteristics are such that it will provide a safe confinement for solidified high-level and alpha-bearing and certain other solid radioactive wastes. Site investigations, as used in this report, cover earth sciences and associated safety analyses. Other site-investigation activities are identified but not otherwise considered here. The repositories under consideration are those consisting of mined cavities in deep continental rocks for accepting wastes in the solid and packaged form. The term deep as used in this report is used solely to emphasize the distinction between the repositories discussed in this report and those for shallow-ground disposal. In general, depths under consideration here are greater than 200 metres. The term continental refers to those geological formations that occur either beneath present-day land masses and adjoining islands or beneath the shallow seas. One of the objectives of site investigations is to collect the site-specific data necessary for the different evaluations, such as modelling required to assess the long-term safety of an underground repository.

Influence of convective-energy transfer on calculated temperature distributions in proposed hard-rock nuclear waste repositories

Energy Technology Data Exchange (ETDEWEB)

Eaton, R R; Reda, D C [Sandia National Labs., Albuquerque, NM (USA)

1982-06-01

This study assesses the relative influence of convective-energy transfer on predicted temperature distributions for a nuclear-waste repository located in water-saturated rock. Using results for energy transfer by conduction only (no water motion) as a basis of comparison, it is shown that a considerable amount of energy can be removed from the repository by pumping out water that migrates into the drift from regions adjacent to the buried waste canisters. Furthermore, the results show that the influence of convective-energy transfer on mine drift cooling requirements can be significant for cases where the in-situ permeability of the rock is greater than one millidarcy (a regime potentially encountered in repository scenarios).

Evaluation of iron-base materials for waste package containers in a salt repository

International Nuclear Information System (INIS)

Westerman, R.E.; Nelson, J.L.; Kuhn, W.L.; Basham, S.G.; Moak, D.A.; Pitman, S.G.

1983-11-01

Design studies for high-level nuclear waste packages for salt repositories have identified low-carbon steel as a candidate material for containers. Among the requirements are strength, corrosion resistance, and fabricability. The studies of the corrosion resistance and structural stability of iron-base materials (particularly low-carbon steel) are treated in this paper. The materials have been exposed in brines that are characteristic of the potential sites for salt repositories. The effects of temperature, radiation level, oxygen level and other parameters are under investigation. The initial development of corrosion models for these environments is presented with discussion of the key mechanisms under consideration. 6 references, 5 figures

Draft Technical Position Subtask 1.1: waste package performance after repository closure. Volume 1

International Nuclear Information System (INIS)

Davis, M.S.; Schweitzer, D.G.

1983-08-01

This document provides guidance to the DOE on the issues and information necessary for the NRC to evaluate waste package performance after repository closure. Minimal performance objectives of the waste package are required by proposed 10 CFR 60. This Draft Technical Position describes the various options available to the DOE for compliance and discusses advantages and disadvantages of various choices. Examples are discussed dealing with demonstrability, predictability and reasonable assurance. The types of performance are considered. The document summarizes presently identified high priority issues needed to evaluate waste package performance after repository closure. 20 references, 7 tables

Thermo-Hydro Mechanical Characteristics and Processes in the Clay Barrier of a High Level Radioactive Waste Repository. State of the Art Report

International Nuclear Information System (INIS)

Villar, M. V.

2004-01-01

This document is a summary of the available information on the thermo-hydro-mechanical properties of the bentonite barrier of a high-level radioactive waste repository and of the processes taking place in it during the successive repository operation phases. Mainly the thermal properties, the volume change processes (swelling and consolidation), the permeability and the water retention capacity are analysed. A review is made of the existing experimental knowledge on the modification of the these properties by the effect of temperature, water salinity, humidity and density of the bentonite, and their foreseen evolution as a consequence of the processes expected in the repository. The compiled evolution refers mostly to the FEBEX (Spain), the MX-80 (USA) and the FoCa (France) bentonite, considered as reference barrier materials in several European disposal concepts. (Author) 102 refs

Thermo-Hydro Mechanical Characteristics and Processes in the Clay Barrier of a High Level Radioactive Waste Repository. State of the Art Report

Energy Technology Data Exchange (ETDEWEB)

Villar, M. V.

2004-07-01

This document is a summary of the available information on the thermo-hydro-mechanical properties of the bentonite barrier of a high-level radioactive waste repository and of the processes taking place in it during the successive repository operation phases. Mainly the thermal properties, the volume change processes (swelling and consolidation), the permeability and the water retention capacity are analysed. A review is made of the existing experimental knowledge on the modification of the these properties by the effect of temperature, water salinity, humidity and density of the bentonite, and their foreseen evolution as a consequence of the processes expected in the repository. The compiled evolution refers mostly to the FEBEX (Spain), the MX-80 (US) and the FoCa (France) bentonite, considered as reference barrier materials in several European disposal concepts. (Author) 102 refs.

An evaluation of environmental effects of the DOE HLW repository siting and characterization program at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Winsor, M.F.; Ulland, L.M.

1989-01-01

This paper presents highlights of the Nevada Nuclear Waste Project Office (NWPO) environmental investigations in progress on the environmental effects of past and proposed activities of the Department of Energy (DOE) at the Yucca Mountain repository. The environmental investigations refer to those studies specifically related to resource evaluation, impact assessment and mitigation planning for the repository program; it is defined to exclude consideration of technical suitability determinations, socioeconomics and transportation. This paper addresses the question of what are the disturbances created by past and proposed DOE activities related to repository siting and characterization at Yucca Mountain. It discusses considerations in linking disturbance to the potential for significant adverse environmental impacts

Rock support for nuclear waste repositories

International Nuclear Information System (INIS)

Abramson, L.W.; Schmidt, B.

1984-01-01

The design of rock support for underground nuclear waste repositories requires consideration of special construction and operation requirements, and of the adverse environmental conditions in which some of the support is placed. While repository layouts resemble mines, design, construction and operation are subject to quality assurance and public scrutiny similar to what is experienced for nuclear power plants. Exploration, design, construction and operation go through phases of review and licensing by government agencies as repositories evolve. This paper discusses (1) the various stages of repository development; (2) the environment that supports must be designed for; (3) the environmental effects on support materials; and (4) alternative types of repository rock support

Waste package reference conceptual designs for a repository in salt

International Nuclear Information System (INIS)

1986-02-01

This report provides the reference conceptual waste package designs for the Office of Nuclear Waste Isolation to baseline these designs, thereby establishing the configuration and interface controls necessary, within the Civilian Radioactive Waste Management Program, formerly the National Waste Terminal Storage Program, to proceed in an orderly manner with preliminary design. Included are designs for the current reference defense high-level waste form from the Savannah River Plant, an optimized commercial high-level waste form, and spent fuel which has been disassembled and compacted into a circular bundle containing either 12 pressurized-water reactor or 30 boiling-water reactor assemblies. For compacted spent fuel, it appears economically attractive to standardize the waste package diameter for all fuel types. The reference waste packages consist of the containerized waste form, a low carbon steel overpack, and, after emplacement, a cover of salt. The overpack is a hollow cylinder with a flat head welded to each end. Its design thickness is the sum of the structural thickness required to resist the 15.4-MPa lithostatic pressure plus the corrosion allowance necessary to assure the required structural thickness will exist through the 1000-year containment period. Based on available data and completed analyses, the reference concepts described in this report satisfy all requirements of the US Department of Energy and the US Nuclear Regulatory Commission with reasonable assurance. In addition, sufficient design maturity exists to form a basis for preliminary design; these concepts can be brought under configuration control to serve as reference package designs. Development programs are identified that will be required to support these designs during the licensing process. 19 refs., 37 figs., 31 tabs

Hydrogeological investigation for sitting disposal repository for high level radioactive waste

International Nuclear Information System (INIS)

Guo Yonghai; Liu Shufen; Lv Chuanhe

2005-01-01

Based on the research experiences of our country and some developed countries in the world, the purpose, process and methods, as well as the function of hydrogeological investigation for sitting disposal repository for high radioactive waste are discussed. Meanwhile, the topic related to the acquisition of hydrogeological parameters is described as well, aiming at providing reference for the future study. (authors)

National Radwaste Repository Mochovce

International Nuclear Information System (INIS)

2000-01-01

In this leaflet the National Radioactive Waste Repository in Mochovce (Repository) is described. The Mochovce National Radioactive Waste Repository is a surface multi-barrier type storage facility for solid and treated solidified radioactive wastes generated from the Slovak Republic nuclear power plants operation and decommissioning, research institutes, laboratories and hospitals. The Repository comprises a system of single- and double-row storage boxes. The first double-row is enclosed by a steel-structure building. The 18 x 6 x 5.5 m storage boxes are made of reinforced concrete. The wall thickness is 600 mm. Two-double-rows, i.e. 80 storage boxes were built as part of Stage I (1 row = 20 storage boxes). Each storage box has a storage capacity of 90 fibre concrete containers of 3.1 m 3 volume. The total storage capacity is 7200 containers with the overall storage volume of 22320 m 3

Fostering New Roles for Librarians: Skills Set for Repository Managers — Results of a Survey in Italy

Directory of Open Access Journals (Sweden)

Maria Cassella

2012-04-01

Full Text Available The open access movement in scholarly communication has grown considerably over the last ten years and it has driven an increase in the number of institutional repositories (IRs. New professional roles and skills had to be developed to secure effective IR management. Collection developmente expertise and metadata curation are regarded as strategic roles for repositories and therefore it is only logical for the library and information community to take on the responsibility for managing these digital archives. However, it has become clear that traditional librarian skills do not suffice anymore to run successful repositories. A richer set of skills is needed, including management and communication skills, technical skills, and expertise with regard to access rights and preservation of digital content. Referring to the work carried out by the SHERPA Project in the UK with regard to the skills set for repository staff, the authors performed a survey among repository managers in Italy to assess the educational and professional background of the repository managers and the skills set required to implement successful institutional repositories. The survey findings show that the professional profile of the repository manager is a multiform and complex one. It requires cross-functional and highly specialised competencies. Italian repository managers are of the opinion that the skills required to promote the repository within the institution and those required to deal with copyright issues as the most essential skills repository managers should acquire and be trained for. Collection development and metadata expertise, familiarity with project management and expertise in repository workflow design are also highly rated. Technical skills are needed to deal with interoperability standards and protocols. In Italy academic curricula do not meet the repository managers’ educational needs. Academic programmes should be developed to include communication

Single or multi-repository concept? A personal contribution to the discussion of pros and cons

International Nuclear Information System (INIS)

Closs, K.-D.; Duphorn, K.; Kuehn, K.

2002-01-01

The coalition agreement concluded between the parties in government, i.e. SPD and Alliance 90/The Greens, after the 1998 federal elections provided for an approach to back-end fuel cycle conditions for German nuclear power plants which differed from the practice intended up to that point. Among other things, only one single repository in deep geologic formations is to be available approximately from 2030 on. Exploration of the Gorleben salt dome is to be interrupted because of prevailing doubts while, at the same time, a basic discussion is to be held about potentially suitable host rock varieties and sites. The 'Working Party of Selection Procedures for Repository Sites (AkEnd)' instituted by the federal government is to elaborate scientific siting criteria under these conditions. The authors, who are members of AkEnd, come to the conclusion, based on technical findings and the historical back-end fuel cycle and siting situation in Germany, that a multi-repository concept incorporates substantial advantages. These are the aspects referred to: - Back-end fuel cycle concept: The multi-repository concept offers clearcut advantages in the far advanced Konrad repository project. This is true also against the background of the volume of waste with negligible heat generation to be managed by public authorities. - Long-term safety: Advantages exist, among other things, with respect to technical safety regarding possible compromises in a single-repository concept and the possible restriction of the number of potential sites. - Methods of detection: Spreading the waste over two or more repositories offers benefits in the technical aspects of detection. - Cost: A differentiated assessment of the cost arising in connection with the total amount of waste to be stored in repositories indicates benefits of a multi-repository concept, especially for the public authorities. (orig.) [de

Analysis of Turkey’s Institutional Open Repositories: An Example of Dokuz Eylül University Institutional Open Repository

Directory of Open Access Journals (Sweden)

Korhan Levent Ertürk

2012-03-01

Full Text Available After the declaration of the Budapest Open Access Initiative in 2001, institutional open repositories are known as the most important tool of the self archiving, which is also known as green road. There are 26 institutional repositories, which are all compatible to international standards. All the institutional open repositories of Turkey mentioned before are listed in international open archive directories. In this study institutional open repository of Dokuz Eylül University is examined and institutional open repositories of Turkey are discussed.

Excavation response in respect of the repository concept for the Konrad mine as seen by the mining authority

International Nuclear Information System (INIS)

Roehl, W.

1989-01-01

In connection with the securing technical check-up of the repository concept for the Konrad mine the Mining Authority of Lower Saxony was asked for a comment on the mining concern of the Konrad plan by the Ministry for Environmental Protection of Lower Saxony. Referring to excavation response the valuation of rock-mechanical data, efficiency of the dams, underground convergences and mining subsidence are important to the realisation of the repository concept

Radioactive waste repository of high ecological safety

International Nuclear Information System (INIS)

Sobolev, I.; Barinov, A.; Prozorov, L.

2000-01-01

With the purpose to construct a radioactive waste repository of high ecological safety and reliable containment, MosNPO 'Radon' specialists have developed an advanced type repository - large diameter well (LBD) one. A project is started for the development of a technology for LDW repository construction and pilot operation of the new repository for 25-30 years. The 2 LDW repositories constructed at the 'Radon' site and the developed monitoring system are described

Consistency analysis of network traffic repositories

NARCIS (Netherlands)

Lastdrager, Elmer; Lastdrager, E.E.H.; Pras, Aiko

Traffic repositories with TCP/IP header information are very important for network analysis. Researchers often assume that such repositories reliably represent all traffic that has been flowing over the network; little thoughts are made regarding the consistency of these repositories. Still, for

Sellafield repository design concept

International Nuclear Information System (INIS)

1998-01-01

Between 1989 and 1997, UK Nirex Ltd carried out a programme of investigations to evaluate the potential of a site adjacent to the BNFL Sellafield works to host a deep repository for the United Kingdom's intermediate-level and certain low-level radioactive waste. The programme of investigations was wound down following the decision in March 1997 to uphold the rejection of the Company's planning application for the Rock Characterisation Facility (RCF), an underground laboratory which would have allowed further investigations to confirm whether or not the site would be suitable. Since that time, the Company's efforts in relation to the Sellafield site have been directed towards documenting and publishing the work carried out. The design concept for a repository at Sellafield was developed in parallel with the site investigations through an iterative process as knowledge of the site and understanding of the repository system performance increased. This report documents the Sellafield repository design concept as it had been developed, from initial design considerations in 1991 up to the point when the RCF planning application was rejected. It shows, from the context of a project at that particular site, how much information and experience has been gained that will be applicable to the development of a deep waste repository at other potential sites

Influence analysis of Github repositories.

Science.gov (United States)

Hu, Yan; Zhang, Jun; Bai, Xiaomei; Yu, Shuo; Yang, Zhuo

2016-01-01

With the support of cloud computing techniques, social coding platforms have changed the style of software development. Github is now the most popular social coding platform and project hosting service. Software developers of various levels keep entering Github, and use Github to save their public and private software projects. The large amounts of software developers and software repositories on Github are posing new challenges to the world of software engineering. This paper tries to tackle one of the important problems: analyzing the importance and influence of Github repositories. We proposed a HITS based influence analysis on graphs that represent the star relationship between Github users and repositories. A weighted version of HITS is applied to the overall star graph, and generates a different set of top influential repositories other than the results from standard version of HITS algorithm. We also conduct the influential analysis on per-month star graph, and study the monthly influence ranking of top repositories.

Local-scale modelling of density-driven flow for the phases of repository operation and post-closure at Beberg

International Nuclear Information System (INIS)

Jaquet, O.; Siegel, P.

2004-09-01

A hydrogeological model was developed for Beberg with the aim of evaluating the impact of a repository (for the operational and post-closure phases) while accounting for the effects of density-driven flow. Two embedded scales were taken into account for this modelling study: a local scale at which the granitic medium was considered as a continuum and a repository scale, where the medium is fractured and therefore was regarded to be discrete. The following step-wise approach was established to model density-driven flow at both repository and local scale: (a) modelling fracture networks at the repository scale, (b) upscaling the hydraulic properties to a continuum at local scale and (c) modelling density-driven flow to evaluate repository impact at local scale. The results demonstrate the strong impact of the repository on the flow field during the phase of operation. The distribution of the salt concentration is affected by a large upcoming effect with increased relative concentration and by the presence of fracture zones carrying freshwater from the surface. The concentrations obtained for the reference case, expressed in terms of percentage with respect to the maximum (prescribed) value in the model, are as follows: ca 30% for the phase of desaturation, and ca 20% for the resaturation phase. For the reference case, the impact of repository operations appears no longer visible after a resaturation period of about 20 years after repository closure; under resaturation conditions, evidence of the operational phase has already disappeared in terms of the observed hydraulic and concentration fields. Sensitivity calculations have proven the importance of explicitly discretising repository tunnels when assessing resaturation time and maximum concentration values. Furthermore, the definition of a fixed potential as boundary condition along the model's top surface is likely to provide underestimated values for the maximum concentration and overestimated flow rates in the

Generic repository design concepts and thermal analysis (FY11)

International Nuclear Information System (INIS)

Howard, Robert; Dupont, Mark; Blink, James A.; Fratoni, Massimiliano; Greenberg, Harris; Carter, Joe; Hardin, Ernest L.; Sutton, Mark A.

2011-01-01

Reference concepts for geologic disposal of used nuclear fuel and high-level radioactive waste in the U.S. are developed, including geologic settings and engineered barriers. Repository thermal analysis is demonstrated for a range of waste types from projected future, advanced nuclear fuel cycles. The results show significant differences among geologic media considered (clay/shale, crystalline rock, salt), and also that waste package size and waste loading must be limited to meet targeted maximum temperature values. In this study, the UFD R and D Campaign has developed a set of reference geologic disposal concepts for a range of waste types that could potentially be generated in advanced nuclear FCs. A disposal concept consists of three components: waste inventory, geologic setting, and concept of operations. Mature repository concepts have been developed in other countries for disposal of spent LWR fuel and HLW from reprocessing UNF, and these serve as starting points for developing this set. Additional design details and EBS concepts will be considered as the reference disposal concepts evolve. The waste inventory considered in this study includes: (1) direct disposal of SNF from the LWR fleet, including Gen III+ advanced LWRs being developed through the Nuclear Power 2010 Program, operating in a once-through cycle; (2) waste generated from reprocessing of LWR UOX UNF to recover U and Pu, and subsequent direct disposal of used Pu-MOX fuel (also used in LWRs) in a modified-open cycle; and (3) waste generated by continuous recycling of metal fuel from fast reactors operating in a TRU burner configuration, with additional TRU material input supplied from reprocessing of LWR UOX fuel. The geologic setting provides the natural barriers, and establishes the boundary conditions for performance of engineered barriers. The composition and physical properties of the host medium dictate design and construction approaches, and determine hydrologic and thermal responses of

Generic repository design concepts and thermal analysis (FY11).

Energy Technology Data Exchange (ETDEWEB)

Howard, Robert (Oak Ridge National Laboratory, Oak Ridge, TN); Dupont, Mark (Savannah River Nuclear Solutions, Aiken, SC); Blink, James A. (Lawrence Livermore National Laboratory, Livermore, CA); Fratoni, Massimiliano (Lawrence Livermore National Laboratory, Livermore, CA); Greenberg, Harris (Lawrence Livermore National Laboratory, Livermore, CA); Carter, Joe (Savannah River Nuclear Solutions, Aiken, SC); Hardin, Ernest L.; Sutton, Mark A. (Lawrence Livermore National Laboratory, Livermore, CA)

2011-08-01

Reference concepts for geologic disposal of used nuclear fuel and high-level radioactive waste in the U.S. are developed, including geologic settings and engineered barriers. Repository thermal analysis is demonstrated for a range of waste types from projected future, advanced nuclear fuel cycles. The results show significant differences among geologic media considered (clay/shale, crystalline rock, salt), and also that waste package size and waste loading must be limited to meet targeted maximum temperature values. In this study, the UFD R&D Campaign has developed a set of reference geologic disposal concepts for a range of waste types that could potentially be generated in advanced nuclear FCs. A disposal concept consists of three components: waste inventory, geologic setting, and concept of operations. Mature repository concepts have been developed in other countries for disposal of spent LWR fuel and HLW from reprocessing UNF, and these serve as starting points for developing this set. Additional design details and EBS concepts will be considered as the reference disposal concepts evolve. The waste inventory considered in this study includes: (1) direct disposal of SNF from the LWR fleet, including Gen III+ advanced LWRs being developed through the Nuclear Power 2010 Program, operating in a once-through cycle; (2) waste generated from reprocessing of LWR UOX UNF to recover U and Pu, and subsequent direct disposal of used Pu-MOX fuel (also used in LWRs) in a modified-open cycle; and (3) waste generated by continuous recycling of metal fuel from fast reactors operating in a TRU burner configuration, with additional TRU material input supplied from reprocessing of LWR UOX fuel. The geologic setting provides the natural barriers, and establishes the boundary conditions for performance of engineered barriers. The composition and physical properties of the host medium dictate design and construction approaches, and determine hydrologic and thermal responses of the

CRIS and Institutional Repositories

Directory of Open Access Journals (Sweden)

A Asserson

2010-04-01

Full Text Available CRIS (Current Research Information Systems provide researchers, research managers, innovators, and others with a view over the research activity of a domain. IRs (institutional repositories provide a mechanism for an organisation to showcase through OA (open access its intellectual property. Increasingly, organizations are mandating that their employed researchers deposit peer-reviewed published material in the IR. Research funders are increasingly mandating that publications be deposited in an open access repository: some mandate a central (or subject-based repository, some an IR. In parallel, publishers are offering OA but replacing subscription-based access with author (or author institution payment for publishing. However, many OA repositories have metadata based on DC (Dublin Core which is inadequate; a CERIF (Common-European Research Information Format CRIS provides metadata describing publications with formal syntax and declared semantics thus facilitating interoperation or homogeneous access over heterogeneous sources. The formality is essential for research output metrics, which are increasingly being used to determine future funding for research organizations.

Peculiarities of the High-Level Concrete-Encased Radwaste Repository Disposition at the Radwaste Disposal Site of the Russian Research Center 'Kurchatov Institute'

International Nuclear Information System (INIS)

Volkov, V.G.; Ponomarev-Stepnoi, N.N.; Gorodetsky, G.G.; Zverkov, Yu.A.; Ivanov, O.P.; Lemus, A.V.; Semenov, S.G.; Stepanov, V.E.; Chesnokov, A.V.; Shisha, A.D.

2006-01-01

The paper presents peculiarities of organization and performance of activities on disposition of the old repository that contained high-level waste and located at the radwaste disposal site of the Russian Research Center 'Kurchatov Institute' in Moscow. The repository was constructed in the late 1950's. A large number of cases with high-level waste were placed in the repository along with low- and intermediate-level waste. When the repository was filled in 1973, the entire radwaste mass was encased in concrete matrix which caused difficulties with the radwaste extraction and made the work on the repository disposition highly hazardous in terms of radiation conditions. Based on results of the preliminary radiation survey of the repository, technologies and equipment to be used in disposition works were selected, and a decision on construction of external radiation shielding around the repository to maintain normal radiation conditions during these works was made. Specific features of the selected radiation shielding design constructed around the repository and of a technology used for the radwaste extraction from the repository are provided. According to the technology, conventional construction machines equipped with a hydraulic hammer or a clamshell were used for destruction of the concrete-encased radwaste mass and extraction of low-level waste. Intermediate- and high-level waste was extracted by remotely controlled robots operating inside the radiation shielding structure. Video cameras and a gamma imager were used for detection of high-level waste or fragments of such radwaste in the mass concrete being destroyed and for guiding remotely controlled robots. Peculiarities of rapid control of changes in radiation conditions in the working areas are presented. This control was performed using a gamma locator with on-line transmission of its data to a PC for their processing. With disposition of this not easily accessible repository, the stage of remediation of old

Three-dimensional model of reference thermal/mechanical and hydrological stratigraphy at Yucca Mountain, southern Nevada

International Nuclear Information System (INIS)

Ortiz, T.S.; Williams, R.L.; Nimick, F.B.; Whittet, B.C.; South, D.L.

1985-10-01

The Nevada Nuclear Waste Storage Investigations (NNWSI) project is currently examining the feasibility of constructing a nuclear waste repository in the tuffs beneath Yucca Mountain. A three-dimensional model of the thermal/mechanical and hydrological reference stratigraphy at Yucca Mountain has been developed for use in performance assessment and repository design studies involving material properties data. The reference stratigraphy defines units with distinct thermal, physical, mechanical, and hydrological properties. The model is a collection of surface representations, each surface representing the base of a particular unit. The reliability of the model was evaluated by comparing the generated surfaces, existing geologic maps and cross sections, drill hole data, and geologic interpolation. Interpolation of surfaces between drill holes by the model closely matches the existing information. The top of a zone containing prevalent zeolite is defined and superimposed on the reference stratigraphy. Interpretation of the geometric relations between the zeolitic and thermal/mechanical and hydrological surfaces indicates that the zeolitic zone was established before the major portion of local fault displacement took place; however, faulting and zeolitization may have been partly concurrent. The thickness of the proposed repository host rock, the devitrified, relatively lithophysal-poor, moderately to densely welded portion of the Topopah Spring Member of the Paintbrush Tuff, was evaluated and varies from 400 to 800 ft in the repository area. The distance from the repository to groundwater level was estimated to vary from 700 to 1400 ft. 13 figs., 1 tab

Geoengineering properties of potential repository units at Yucca Mountain, southern Nevada

International Nuclear Information System (INIS)

Tillerson, J.R.; Nimick, F.B.

1984-12-01

The Nevada Nuclear Waste Storage Investigations (NNWSI) Project is currently evaluating volcanic tuffs at the Yucca Mountain site, located on and adjacent to the Nevada Test Site, for possible use as a host rock for a radioactive waste repository. The behavior of tuff as an engineering material must be understood to design, license, construct, and operate a repository. Geoengineering evaluations and measurements are being made to develop confidence in both the analysis techniques for thermal, mechanical, and hydrothermal effects and the supporting data base of rock properties. The analysis techniques and the data base are currently used for repository design, waste package design, and performance assessment analyses. This report documents the data base of geoengineering properties used in the analyses that aided the selection of the waste emplacement horizon and in analyses synopsized in the Environmental Assessment Report prepared for the Yucca Mountain site. The strategy used for the development of the data base relies primarily on data obtained in laboratory tests that are then confirmed in field tests. Average thermal and mechanical properties (and their anticipated variations) are presented. Based upon these data, analyses completed to date, and previous excavation experience in tuff, it is anticipated that existing mining technology can be used to develop stable underground openings and that repository operations can be carried out safely

Status of Equipment Development for a High-Level Waste Repository in Germany

International Nuclear Information System (INIS)

Biurrun, E.; Haverkamp, B.; Filbert, W.; Bollingerfehr, W.; Graf, R.

2009-01-01

In Germany, a potential site for a deep geological repository mainly for heat generating high-level waste was selected back on February 22, 1977: a salt dome located near the village of Gorleben, at the shores of the Elbe River in Northern Germany. Concurrent with site exploration from the surface, and later exploration mine construction, a large-scale R and D effort was conducted to have the science and technology needed to license and later operate a repository available when needed. An important part of these efforts was the development and 1:1 scale demonstration of all technologies required to run a repository, which had not been state-of-the-art. Underground exploration of the Gorleben site has come to a moratorium due to political decisions taken by the former Federal Government formed by a coalition between the Social Democrats and the Green Party back in 2000. However, research and development in regard to emplacement techniques and equipment has continued. This paper reflects the consistent, long-term technological effort that has led to having available all advanced technologies required to run a repository for spent fuel and HLW. The paper details previous achievements and points at present optimization work. (authors)

Subseabed radionuclide migration studies and preliminary repository design concepts

International Nuclear Information System (INIS)

Brush, L.H.

1982-01-01

Geochemical research carried out by the US Subseabed Disposal Program is described. Data from studies of high-temperature interactions between sediments and pore water (seawater) and from studies of sorption and diffusion of radionuclides in oxidized, deep-sea sediments are used, along with results from heat transfer studies, to predict migration rates of raionuclides in a subseabed repository. Preliminary results for most radionuclides in oxidized sediments are very encouraging. Fission products with moderate K/sub D/ values (10 2 to 10 5 ml/g) and actinides with high K/sub D/ values (10 3 to 10 6 ml/g) would not migrate significant distances before decaying to innocuous concentrations. Among this group are 137 Cs, 90 Sr, and 239 Pu. The results for anionic species in oxidized sediments are less encouraging. Planning for field verification of these laboratory and modeling studies is currently under way. Conceptual repository designs and emplacement options are also described. 33 references, 15 figures, 1 table

R and D on performance assessment of a potential LILW repository

Energy Technology Data Exchange (ETDEWEB)

Hwang, Yong Soo; Lee, Sung Hee; Han, Kyung Won; Lee, Y M

2001-01-01

In this technical report Important issues and assessment methods related to post-closure safety of a proposed repository has been discussed, regarding LILW disposal. At first, to summarize the new proposal on the amendment of the MOST Notice 96-16, KAERI set up the overall directions on future R and D over performance assessment. In addition relevant overseas project such as Finnish POSIVA's VLJ repository project was thoroughly reviewed along with the recent progress of the gas generation and migration R and D. In the post-closure safety analysis of the VLJ repository, in addition to the normal evolution scenario, several disturbed evolution and accident scenarios have been analysed. The groundwater flow analysis and the biosphere analysis have been evaluated. The result of the safety analysis show that radiation doses of any significance are caused only if a well is bored in the vicinity of the repository or if the groundwater discharge spot is inhabited and used for cultivation. in the reference scenario the maximum expectation value of the individual dose rate is 0.03 mSv/a. in the realistic scenario the maximum expectation value of the dose rate is 0.0002 mSv/a In general gas generation sources are represented by radioactive gases and non-radioactive gases. The amount of radioactive gases is little that it does not make a significant influence on the safety of LILW repository, however non-radioactive gases can cause safety problem. As mentioned above, gas of LILW generated by corrosion and microbiology and their production rate can be estimated by computer simulation and long-term experiment.

R and D on performance assessment of a potential LILW repository

Energy Technology Data Exchange (ETDEWEB)

Hwang, Yong Soo; Lee, Sung Hee; Han, Kyung Won; Lee, Y. M

2001-01-01

In this technical report Important issues and assessment methods related to post-closure safety of a proposed repository has been discussed, regarding LILW disposal. At first, to summarize the new proposal on the amendment of the MOST Notice 96-16, KAERI set up the overall directions on future R and D over performance assessment. In addition relevant overseas project such as Finnish POSIVA's VLJ repository project was thoroughly reviewed along with the recent progress of the gas generation and migration R and D. In the post-closure safety analysis of the VLJ repository, in addition to the normal evolution scenario, several disturbed evolution and accident scenarios have been analysed. The groundwater flow analysis and the biosphere analysis have been evaluated. The result of the safety analysis show that radiation doses of any significance are caused only if a well is bored in the vicinity of the repository or if the groundwater discharge spot is inhabited and used for cultivation. in the reference scenario the maximum expectation value of the individual dose rate is 0.03 mSv/a. in the realistic scenario the maximum expectation value of the dose rate is 0.0002 mSv/a In general gas generation sources are represented by radioactive gases and non-radioactive gases. The amount of radioactive gases is little that it does not make a significant influence on the safety of LILW repository, however non-radioactive gases can cause safety problem. As mentioned above, gas of LILW generated by corrosion and microbiology and their production rate can be estimated by computer simulation and long-term experiment.

Some geochemical considerations for a potential repository site in tuff at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Erdal, B.R.; Bish, D.L.; Crowe, B.M.; Daniels, W.R.; Ogard, A.E.; Rundberg, R.S.; Vaniman, D.T.; Wolfsberg, K.

1982-01-01

The Nevada Nuclear Waste Storage Investigations, which is evaluating potential locations for a high-level waste repository at the Nevada Test Site and environs, is currently focusing its investigations on tuff, principally in Yucca Mountain, as a host rock. This paper discusses some of the geochemical investigations. Particular emphasis is placed on definition of some basic elements and necessary technical approaches for the geochemistry data acquisition and modeling program. Some site-specific tuff geochemical information that is important for site selection and repository performance will be identified and the current status of knowledge will then be discussed

THEREDA - a contribution to long-term safety of repositories of nuclear and non-nuclear wastes

International Nuclear Information System (INIS)

Altmaier, M.; Kienzler, B.; Marquardt, C.M.; Neck, V.; Voigt, W.; Wilhelm, S.

2008-01-01

Long-term safety analyses of German repositories of radioactive waste as well as underground repositories for chemical toxic waste and other uses (contaminated site remediation) urgently require a standardized, comprehensive thermodynamic reference database. The former 'Thermodynamic Standard Database Working Party' was set up to establish such a database. The activities of that group have been supported within the integrated 'THEREDA' (Thermodynamic Reference Database) project since July 2006 for an initial period of 3 years by the German Federal Ministries of Education and Research, of Economics, and by the Federal Office of Radiation Protection. THEREDA at present is composed of 5 partner institutions essentially representing the key German research institutions in the field of repository safety research. THEREDA is to improve the transparency and validity of safety analyses in Germany and, for the first time, provides consistent thermodynamic datasets for the repository options discussed in Germany. Quality levels are indicated for each thermodynamic quantity on the basis of unambiguously defined evaluation criteria, which allow users to either include or exclude data in accordance with the specific problems at hand. Missing thermodynamic data are substituted in THEREDA by well-founded estimates, thus permitting future model calculations for safety analysis to be carried out on a clearly broader basis of data. The data are managed centrally in a database and will be available to users free of charge on the Internet. Import formats allowing THEREDA to be transferred into the most common modeling codes (EQ3/6, PHREEQC, Geochemist's Workbench, CHEMAPP, etc.) are also made available free of charge. (orig.)

Nuclear waste repository design and construction

International Nuclear Information System (INIS)

Bohlke, B.M.; Monsees, J.E.

1987-01-01

Extensive underground excavation will be required for construction of a mined geologic repository for nuclear waste. Hundreds of thousands of feet of drift will be required based on the conceptual layout design for each candidate nuclear waste repository. Comparison of boring and blasting excavation methods are discussed, as are special design and construction requirements (e.g., quality assurance procedures and performance assessment) for the nuclear waste repository. Comparisons are made between boring and blasting construction methods for the repository designs proposed for salt, volcanic tuff, and basalt

An assessment of the effect on Olkiluoto repository capacity achievable with advanced fuel cycles

Energy Technology Data Exchange (ETDEWEB)

Juutilainen, P.; Viitanen, T. [VTT Technical Research Centre of Finland, P.O. Box 1000, FI-02044 VTT (Finland)

2013-07-01

Previously a few scenarios have been simulated for transition from thermal to fast reactor fleet in Finland in order to determine how much the transuranic inventory could be reduced with the partitioning and transmutation (P-T) technologies. Those calculations, performed with COSI6 code developed by CEA, are extended in the present study, in which the effect of P-T on the capacity of the planned final disposal repository at Olkiluoto (Finland) is evaluated by taking into account the created fission products and transuranic residuals from the reprocessing operations. The decay heat is assumed to be the most restrictive factor in defining the waste disposal packing density. The repository capacity evaluation of this study is based on the comparison of the decay heats produced by the deposited waste in various scenarios. The reference scenario of this article involves only Light Water Reactors (LWR) in an open fuel cycle. The capacity requirement of the geological repository is estimated in a few closed fuel cycle scenarios, all including actinide transmutation with Fast Reactors (FR). The comparison between the P-T scenarios and reference is based on the decay heat production of the deposited waste. The COSI6 code is used for simulations to provide the repository decay heat curves. Applying the closed fuel cycle would change the disposal concept and schedule, because of which it is not quite straightforward to assess the impact of P-T on the capacity. However, it can be concluded that recycling the transuranic nuclides probably decreases the required volume for the disposal, but thermal dimensioning analysis is needed for more specific conclusions.

Global nuclear waste repository proposal highlights Australia's nuclear energy vacuum

International Nuclear Information System (INIS)

Anon.

1999-01-01

The Pangea proposal is disscused and considered relevant to Australia. A five-year research program by the company has identified Australia and Argentina as having the appropriate geological, economic and democratic credentials for such a deep repository, with Australia being favoured. A deep repository would be located where the geology has been stable for several hundred million years, so that there need not be total reliance on a robust engineered barrier system to keep the waste securely isolated for thousands of years. It would be a commercial undertaking and would have dedicated port and rail infrastructure. It would take spent fuel and other wastes from commercial reactors, and possibly also waste from weapons disposal programs. Clearly, while the primary ethical and legal principle is that each country is entirely responsible for its own waste, including nuclear waste (polluter pays etc), the big question is whether the concept of an international waste repository is acceptable ethically. Political and economic questions are secondary to this. By taking a fresh look at the reasons for the difficulties which have faced most national repository programs, and discarding the preconception that each country must develop its own disposal facilities, it is possible to define a class of simple, superior high isolation sites which may provide a multi-national basis for solving the nuclear waste disposal problem. The relatively small volumes of high-level wastes or spent fuel which arise from nuclear power production make shared repositories a feasible proposition. For small countries, the economies of scale which can be achieved make the concept attractive. For all countries, objective consideration of the relative merits of national and multi-national solutions is a prudent part of planning the management of long-lived radioactive wastes

Environmental remediation of high-level nuclear waste in geological repository. Modified computer code creates ultimate benchmark in natural systems

International Nuclear Information System (INIS)

Peter, Geoffrey J.

2011-01-01

Isolation of high-level nuclear waste in permanent geological repositories has been a major concern for over 30 years due to the migration of dissolved radio nuclides reaching the water table (10,000-year compliance period) as water moves through the repository and the surrounding area. Repositories based on mathematical models allow for long-term geological phenomena and involve many approximations; however, experimental verification of long-term processes is impossible. Countries must determine if geological disposal is adequate for permanent storage. Many countries have extensively studied different aspects of safely confining the highly radioactive waste in an underground repository based on the unique geological composition at their selected repository location. This paper discusses two computer codes developed by various countries to study the coupled thermal, mechanical, and chemical process in these environments, and the migration of radionuclide. Further, this paper presents the results of a case study of the Magma-hydrothermal (MH) computer code, modified by the author, applied to nuclear waste repository analysis. The MH code verified by simulating natural systems thus, creating the ultimate benchmark. This approach based on processes similar to those expected near waste repositories currently occurring in natural systems. (author)

Repository for spent nuclear fuel. Preliminary construction description - layout D Oskarshamn the Simpevarp area

International Nuclear Information System (INIS)

2006-02-01

This report presents the preliminary design of a repository located in the Simpevarp area. The description has been disposed so as to deal primarily with the site dependent layouts for the above- and underground constructions. The report is disposed as follows: c1 gives the background and some basic information. Chapter 2 presents the demands and necessary conditions that take precedence when adapting the plant to the local conditions, construction, operation and closure. Chapter 3 is a general description of the area, its infrastructure and the specific sites that have been studied. Chapter 4-5 describe the design of the plant for the two chosen sites. Chapter 6 gives a review of data for the plant, and Chapter 7 'References' is the last part of the main document. The appendices A-I give brief information on the general, non-site specific, parts of the plant, e.g. buildings, life cycle, system, operation and organization

Repository for spent nuclear fuel. Preliminary construction description - layout D Oskarshamn the Laxemar area

International Nuclear Information System (INIS)

2006-05-01

This report presents the preliminary design of a repository located in the Laxemar area. The description has been disposed so as to deal primarily with the site dependent layouts for the above- and underground constructions. The report is disposed as follows: Chapter 1 gives the background and some basic information. Chapter 2 presents the demands and necessary conditions that take precedence when adapting the plant to the local conditions, construction, operation and closure. Chapter 3 is a general description of the area, its infrastructure and the specific sites that have been studied. Chapters 4-5 describe the design of the plant for the two chosen sites. Chapter 6 gives a review of data for the plant, and Chapter 7 'References' is the last part of the main document. The appendices A-I give brief information on the general, non-site specific, parts of the plant, e.g. buildings, life cycle, system, operation and organization

Monitored Geologic Repository Project Description Document

International Nuclear Information System (INIS)

Curry, P. M.

2001-01-01

The primary objective of the Monitored Geologic Repository Project Description Document (PDD) is to allocate the functions, requirements, and assumptions to the systems at Level 5 of the Civilian Radioactive Waste Management System (CRWMS) architecture identified in Section 4. It provides traceability of the requirements to those contained in Section 3 of the ''Monitored Geologic Repository Requirements Document'' (MGR RD) (YMP 2000a) and other higher-level requirements documents. In addition, the PDD allocates design related assumptions to work products of non-design organizations. The document provides Monitored Geologic Repository (MGR) technical requirements in support of design and performance assessment in preparing for the Site Recommendation (SR) and License Application (LA) milestones. The technical requirements documented in the PDD are to be captured in the System Description Documents (SDDs) which address each of the systems at Level 5 of the CRWMS architecture. The design engineers obtain the technical requirements from the SDDs and by reference from the SDDs to the PDD. The design organizations and other organizations will obtain design related assumptions directly from the PDD. These organizations may establish additional assumptions for their individual activities, but such assumptions are not to conflict with the assumptions in the PDD. The PDD will serve as the primary link between the technical requirements captured in the SDDs and the design requirements captured in US Department of Energy (DOE) documents. The approved PDD is placed under Level 3 baseline control by the CRWMS Management and Operating Contractor (M and O) and the following portions of the PDD constitute the Technical Design Baseline for the MGR: the design characteristics listed in Table 1-1, the MGR Architecture (Section 4.1), the Technical Requirements (Section 5), and the Controlled Project Assumptions (Section 6)

Monitored Geologic Repository Project Description Document

International Nuclear Information System (INIS)

Curry, P.

2000-01-01

The primary objective of the Monitored Geologic Repository Project Description Document (PDD) is to allocate the functions, requirements, and assumptions to the systems at Level 5 of the Civilian Radioactive Waste Management System (CRWMS) architecture identified in Section 4. It provides traceability of the requirements to those contained in Section 3 of the ''Monitored Geologic Repository Requirements Document'' (MGR RD) (CRWMS M and O 2000b) and other higher-level requirements documents. In addition, the PDD allocates design related assumptions to work products of non-design organizations. The document provides Monitored Geologic Repository (MGR) engineering design basis in support of design and performance assessment in preparing for the Site Recommendation (SR) and License Application (LA) milestones. The engineering design basis documented in the PDD is to be captured in the System Description Documents (SDDs) which address each of the systems at Level 5 of the CRWMS architecture. The design engineers obtain the engineering design basis from the SDDs and by reference from the SDDs to the PDD. The design organizations and other organizations will obtain design related assumptions directly from the PDD. These organizations may establish additional assumptions for their individual activities, but such assumptions are not to conflict with the assumptions in the PDD. The PDD will serve as the primary link between the engineering design basis captured in the SDDs and the design requirements captured in U.S. Department of Energy (DOE) documents. The approved PDD is placed under Level 3 baseline control by the CRWMS Management and Operating Contractor (M and O) and the following portions of the PDD constitute the Technical Design Baseline for the MGR: the design characteristics listed in Table 2-1, the MGR Architecture (Section 4.1),the Engineering Design Bases (Section 5), and the Controlled Project Assumptions (Section 6)

Cultural text mining: using text mining to map the emergence of transnational reference cultures in public media repositories

NARCIS (Netherlands)

Pieters, Toine; Verheul, Jaap

2014-01-01

This paper discusses the research project Translantis, which uses innovative technologies for cultural text mining to analyze large repositories of digitized public media, such as newspapers and journals.1 The Translantis research team uses and develops the text mining tool Texcavator, which is

Groundwater flow reference model of the Meuse/Haute-Marne region: implications on performance analysis of high and intermediate level and long lived radwaste repository in clay formation

International Nuclear Information System (INIS)

Benabderrahmane, H.; Plas, F.; Yven, B.; Cornaton, F.; Perrochet, P.; Kerrou, J.; Stucki, J.; Caloz, P.

2010-01-01

flow conditions at the bottom and at the sides of the model. - Volumetric extraction due to pumping in the Albian aquifer in the Paris region (50'000 m 3 /day). The regional flow model was calibrated with neutral faults against 1255 measured hydraulic heads. Top surface head conditions were evaluated by calibrating the inflow fluxes and the hydraulic conductivity distribution of the outcropping formations using 400 head measurements. The mean discrepancy between the measured and computed values is less than 9 m. At local scale, a reference flow model of the Oxfordian and Dogger aquifers, respectively overlaying and underlaying the Callovo-Oxfordian host formation, is calibrated against measured hydraulic heads at Andra boreholes and the flow fields of these aquifers at sector scale derived from hydrogeologic, geologic and seismic data acquired from the last site investigation campaign (2007-2008). It includes the hydraulically active faults of Marne and Poissons as well as the less active faults of Gondrecourt. The parameterization that characterize the hydrogeological role of these faults leads to the calibration of the flow with a mean discrepancy between computed and measured values less than 3 m. The performance analysis of the repository emplacement within the 250 km 2 Andra site area was carried out using the stationary velocity field of this reference flow model and computing (i) the travel time and cumulative distance of purely advective particle trajectories and (ii) the lifetime expectancy of water molecules crossing the waste repository and migrating by hydro-dispersive motion (advection, dispersion and diffusion) through the 3-D structures towards the outlets of the aquifer system, using the method proposed by Cornaton and Perrochet. The corrosion of metals contained in intermediate level waste under reduced chemical conditions will lead to the production of hydrogen gas during the post closure phase of a radioactive waste repository. A rough

Data base for a site-specific migration analysis radioactive elements out of a waste repository

Energy Technology Data Exchange (ETDEWEB)

Hadermann, J

1981-11-01

Migration analysis is of considerable importance in long-term safety analysis of radioactive waste repositories. In a first step our plans are to calculate transport of radionuclides using data - as far as possible - for an undisturbed hydrogeology. Thereby a reference case is defined. In a later step, possible events and processes can be considered leading to a deviation from the reference case. The present work gives the data base for a selected part of a comprehensive geosphere transport calculation. We restrict ourselves to a critical evaluation of parameters pertinent to the migration analysis of the /sup 245/Cm chain. This includes the important nuclide /sup 237/Np. For the first time we are able to perform a site specific calculation for repositories planned in deep geologic formations in Switzerland. The well-known fact that the data basis is extremely sparse is pointed out once more and concretized in detail.

Biological Web Service Repositories Review.

Science.gov (United States)

Urdidiales-Nieto, David; Navas-Delgado, Ismael; Aldana-Montes, José F

2017-05-01

Web services play a key role in bioinformatics enabling the integration of database access and analysis of algorithms. However, Web service repositories do not usually publish information on the changes made to their registered Web services. Dynamism is directly related to the changes in the repositories (services registered or unregistered) and at service level (annotation changes). Thus, users, software clients or workflow based approaches lack enough relevant information to decide when they should review or re-execute a Web service or workflow to get updated or improved results. The dynamism of the repository could be a measure for workflow developers to re-check service availability and annotation changes in the services of interest to them. This paper presents a review on the most well-known Web service repositories in the life sciences including an analysis of their dynamism. Freshness is introduced in this paper, and has been used as the measure for the dynamism of these repositories. © 2017 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

A model for the analysis of a normal evolution scenarios for a deep geological granite repository for high-level radioactive waste

International Nuclear Information System (INIS)

Cormenzana Lopez, J.L.; Cunado, M.A.; Lopez, M.T.

1996-01-01

The methodology usually used to evaluate the behaviour of deep geological repositories for high-level radioactive wastes comprises three phases: Identification of factors (processes, characteristics and events) that can affect the repository. Generation of scenarios. In general, a normal evolution scenario (Reference Scenario) and various disruptive scenarios (earthquake, human intrusion, etc) are considered. Evaluation of the behaviour of the repository in each scenario. The normal evolution scenario taking into account all factors with a high probability of occurrence is the first to be analysed. The performance assessment of behaviour being carried out by ENRESA for the AGP Granite has led to the identification of 63 of these factors. To analyse repository behaviour in the normal evolution scenario, it is necessary to first of all create an integrated model of the global system. This is a qualitative model including the 63 factors identified. For a global view of a such a complex system, it is very useful to graphically display the relationship between factors in an Influence Diagram. This paper shows the Influence Diagram used in the analysis of the AGP Granite Reference Scenario. (Author)

IAEA safeguards for geological repositories

International Nuclear Information System (INIS)

Moran, B.W.

2005-01-01

In September. 1988, the IAEA held its first formal meeting on the safeguards requirements for the final disposal of spent fuel and nuclear material-bearing waste. The consensus recommendation of the 43 participants from 18 countries at this Advisory Group Meeting was that safeguards should not terminate of spent fuel even after emplacement in, and closure of, a geologic repository.' As a result of this recommendation, the IAEA initiated a series of consultants' meetings and the SAGOR Programme (Programme for the Development of Safeguards for the Final Disposal of Spent Fuel in Geologic Repositories) to develop an approach that would permit IAEA safeguards to verify the non-diversion of spent fuel from a geologic repository. At the end of this process, in December 1997, a second Advisory Group Meeting, endorsed the generic safeguards approach developed by the SAGOR Programme. Using the SAGOR Programme results and consultants' meeting recommendations, the IAEA Department of Safeguards issued a safeguards policy paper stating the requirements for IAEA safeguards at geologic repositories. Following approval of the safeguards policy and the generic safeguards approach, the Geologic Repository Safeguards Experts Group was established to make recommendations on implementing the safeguards approach. This experts' group is currently making recommendations to the IAEA regarding the safeguards activities to be conducted with respect to Finland's repository programme. (author)

Thermohydromechanical stability analysis upon joint characteristics and depth variations in the region of an underground repository for the study of a disposal concept of high level radioactive wastes

International Nuclear Information System (INIS)

Kim, Jhin Wung; Bae, Dae Suk; Kang, Chul Hyung; Choi, Jong Won

2003-02-01

The objective of the present study is to understand a long term(500 years) thermohydromechanical interaction behavior in the vicinity of a repository cavern upon joint location and repository depth variations, and then, to contribute to the development of a disposal concept. The model includes a saturated rock mass, PWR spent fuels in a disposal canister surrounded by compacted bentonite inside a deposition hole, and mixed bentonite backfilled in the rest of the space within a cavern. It is assumed that two joint sets exist within a model. A joint set 1 includes 56 .deg. dip joints, 20m spaced, and a joint set 2 is in the direction perpendicular to a joint set 1 and includes 34 .deg. dip joints, 20m spaced. In order to understand the behavior change upon joint location variations, 5 different models of 500m depth are analyzed, and additional 3 different models of 1km depth are analyzed to understand the effect of a depth variation. The two dimensional distinct element code, UDEC is used for the analysis. To understand the joint behavior adjacent to a repository cavern, Barton-Bandis joint model is used. Effect of the decay heat for PWR spent fuels on a repository model is analyzed, and a steady state algorithm is used for a hydraulic analysis. According to the thermohydromechanical interaction behavior of a repository model upon variations of joint locations and a repository depth, during the period of 500 years from waste emplacement, the effect of a depth variation on the stress and displacement behavior of a model is comparatively smaller than the effect of decay heat from radioactive materials. From the study of the joint location variation effect, it is advisable not to locate an underground opening in the region very close to the joint crossings

Changes in the referent body location and configuration may underlie human gait, as confirmed by findings of multi-muscle activity minimizations and phase resetting.

Science.gov (United States)

Feldman, Anatol G; Krasovsky, Tal; Baniña, Melanie C; Lamontagne, Anouk; Levin, Mindy F

2011-04-01

Locomotion is presumably guided by feed-forward shifts in the referent body location in the desired direction in the environment. We propose that the difference between the actual and the referent body locations is transmitted to neurons that virtually diminish this difference by appropriately changing the referent body configuration, i.e. the body posture at which muscles reach their recruitment thresholds. Muscles are activated depending on the gap between the actual and the referent body configurations resulting in a step being made to minimize this gap. This hypothesis implies that the actual and the referent leg configurations can match each other at certain phases of the gait cycle, resulting in minimization of leg muscle activity. We found several leg configurations at which EMG minima occurred, both during forward and backward gait. It was also found that the set of limb configurations associated with EMG minima can be changed by modifying the pattern of forward and backward gait. Our hypothesis predicts that, in response to perturbations of gait, the rate of shifts in the referent body location can temporarily be changed to avoid falling. The rate influences the phase of rhythmic limb movements during gait. Therefore, following the change in the rate of the referent body location, the whole gait pattern, for all four limbs, will irreversibly be shifted in time (long-lasting and global phase resetting) with only transient changes in the gait speed, swing and stance timing and cycle duration. Aside from transient changes in the duration of the swing and/or stance phase in response to perturbation, few previous studies have documented long-lasting and global phase resetting of human gait in response to perturbation. Such resetting was a robust finding in our study. By confirming the notion that feed-forward changes in the referent body location and configuration underlie human locomotion, this study solves the classical problem in the relationship between

Gas generation in repositories

International Nuclear Information System (INIS)

Biddle, P.; Rees, J.H.; McGahan, D.; Rushbrook, P.E.

1987-09-01

The nature and quantities of gases likely to be produced by various processes in repositories for low level and intermediate level radioactive wastes are examined in this preliminary study. Many simplifying assumptions are made where published or experimental data is unavailable. The corrosion of the canisters and metallic components in wastes is likely to be the major gas production process in both types of repository. A significant contribution from microbiological activity is expected to occur in low level repositories, predominantly where no cement grouting of the cans has been carried out. A number of areas for further research, required before a more comprehensive study could be carried out, have been identified. (author)

Initiative to manufacture and characterize Baculovirus Reference Material

NARCIS (Netherlands)

Kamen, A.; Aucoin, M.; Merten, O.W.; Alves, P.C.M.; Hashimoto, Y.; Airenne, K.; Hu, Y.C.; Mezzina, M.; Oers, van M.M.

2011-01-01

This letter to the editor brings to the attention of researchers an initiative to develop a baculovirus reference material repository. To be successful this initiative needs the support of a broad panel of researchers working with baculovirus vectors for recombinant protein production and gene

SUBSURFACE REPOSITORY INTEGRATED CONTROL SYSTEM DESIGN

International Nuclear Information System (INIS)

Randle, D.C.

2000-01-01

The primary purpose of this document is to develop a preliminary high-level functional and physical control system architecture for the potential repository at Yucca Mountain. This document outlines an overall control system concept that encompasses and integrates the many diverse process and communication systems being developed for the subsurface repository design. This document presents integrated design concepts for monitoring and controlling the diverse set of subsurface operations. The Subsurface Repository Integrated Control System design will be composed of a series of diverse process systems and communication networks. The subsurface repository design contains many systems related to instrumentation and control (I andC) for both repository development and waste emplacement operations. These systems include waste emplacement, waste retrieval, ventilation, radiological and air monitoring, rail transportation, construction development, utility systems (electrical, lighting, water, compressed air, etc.), fire protection, backfill emplacement, and performance confirmation. Each of these systems involves some level of I andC and will typically be integrated over a data communications network throughout the subsurface facility. The subsurface I andC systems will also interface with multiple surface-based systems such as site operations, rail transportation, security and safeguards, and electrical/piped utilities. In addition to the I andC systems, the subsurface repository design also contains systems related to voice and video communications. The components for each of these systems will be distributed and linked over voice and video communication networks throughout the subsurface facility. The scope and primary objectives of this design analysis are to: (1) Identify preliminary system-level functions and interfaces (Section 6.2). (2) Examine the overall system complexity and determine how and on what levels the engineered process systems will be monitored

A repository released-dose model for the evaluation of long-lived fission product transmutation effectiveness

International Nuclear Information System (INIS)

Davidson, J.W.

1995-01-01

A methodology has been developed to quantify the total integrated dose due to a radionuclide species i emplaced in a geologic repository; the focus is on the seven long-lived fission products (LLFPs). The methodology assumes continuous exposure water contaminated with species i at the accessible environment (i.e., just beyond the geologic barrier afforded by the geologic repository). The dose integration is performed out to a reference post-release time. The integrated dose is a function of the total initial inventory of radionuclide i the repository, the time at which complete and instantaneous failure of the engineered barrier (e.g., waste canister) in, a geologic repository occurs, the fractional dissolution rate (from waste solid form) of radionuclide i in ground water, the ground water travel time to the accessible environment, the retardation factor (sorption on the geologic media) for radionuclide i, the time after radionuclide begins to enter the biosphere. In order to assess relative dose, the ratio of total integrated dose to that for a reference LLFP species j (e.g., 99 Tc) was defined. This ratio is a measure of the relative benefit of transmutation of other LLFPs compared to 99 Tc. This methodology was further developed in order to quantify the integrated dose reduction per neutron utilized for LLFP transmutation in accelerator-driven transmutation technologies (ADTT). This measure of effectiveness is a function of the integrated dose due to LLFP species i, the number of total captures in LLFP species i chain per LLFP nuclide fed to the chain at equilibrium, and the number of total captures in related transmutation product (TP) chains per capture in the LLFP species i chain. To assess relative transmutation effectiveness, the ratio of integrated dose reduction per neutron utilization to that for a reference LLFP species j (e.g., 99 Tc) was defined. This relative measure of effectiveness was evaluated LLFP transmutation strategy

Information about activity, status and radiation conditions of Republic radioactive waste repository

International Nuclear Information System (INIS)

Saidumarov, P.

2000-01-01

All radioactive wastes in the Republic of Uzbekistan are stored in the Republic Radioactive Waste Repository in Parkent district of Tashkent region. In the facility there are 2 tanks for solid radioactive waste, each of 800 m 3 , one of them is full, second is in operation; 2 tanks for liquid radioactive waste each tank of 200 m 3 , both of them are empty; 6 storages, each of 3 m 3 all of them are empty; 3 storages for spent radioactive sources, one of them is full, 2 of them are in operation; 4 storages for high level radioactive waste, each storage of 3.5 m 3 , one of them is in operation, 3 are empty; one sealed storage containing 135 m 3 of concrete blocks with waste from electronic industry. According to conclusions of a few competent examinations RRWR does not cause damage to the environment. Geographic location and technical conditions of the repository are satisfactory. Low deposition of underground water (62 m) excludes penetration of radioisotopes. There were no radiation accidents during the repository operation

Nuclear waste repository siting

International Nuclear Information System (INIS)

Soloman, B.D.; Cameron, D.M.

1987-01-01

This paper discusses the geopolitics of nuclear waste disposal in the USA. Constitutional choice and social equity perspectives are used to argue for a more open and just repository siting program. The authors assert that every potential repository site inevitably contains geologic, environmental or other imperfections and that the political process is the correct one for determining sites selected

Granite-repository - geochemical environment

International Nuclear Information System (INIS)

1979-04-01

Some geochemical data of importance for a radioactive waste repository in hard rock are reviewed. The ground water composition at depth is assessed. The ground water chemistry in the vicinity of uranium ores is discussed. The redox system in Swedish bedrock is described. Influences of extreme climatic changes and of repository mining and construction are also evaluated

Workshop: Creating Your Institutional Research Repository

KAUST Repository

Grenz, Daryl M.

2016-11-08

In 2002, the Scholarly Publishing and Academic Resources Coalition (SPARC) proposed the concept of an institutional repository to simultaneously disrupt and enhance the state of scholarly communications in the academic world. Thirteen years later, thousands of universities and other institutions have answered this call, but many more have not due to gaps in budgets, awareness and, most of all, practical guidance on creating an institutional repository. This workshop provides you with an essential primer on what it takes to establish a fully-functioning institutional repository. Every aspect of the process will be covered, including policies, procedures, staffing guidelines, workflows and repository technologies.

The site selection process for a spent fuel repository in Finland. Summary report

Energy Technology Data Exchange (ETDEWEB)

McEwen, T. [EnvirosQuantiSci (United Kingdom); Aeikaes, T. [Posiva Oy, Helsinki (Finland)

2000-12-01

consequence of the change in primary legislation that resulted in spent fuel from the Loviisa power plant having to be disposed of in Finland, with the result that the island of Haestholmen was added to the list of potential disposal sites, is explained. The results of these detailed investigations are discussed in terms of the development of lithological and structural models of these sites, and with reference to the development of an understanding of their hydrogeological and hydrochemical environments and the generation of groundwater flow and hydrochemical models. These last two subjects are discussed with reference to their significance for spent fuel disposal. In addition, the constructability of the rock mass at these sites is described, including how a repository could be fitted into the rock mass, taking into account site-specific factors, in particular the location and orientation of fracture zones. The constructability of the Olkiluoto site is described in more detail. Other factors that could be of significance for site selection, namely future climate change and seismicity, are also discussed. The selection of Olkiluoto from these four sites is described with reference to the requirements of a disposal site, as specified by Government, and to factors such as long-term safety, the feasibility of repository development, the possibility of repository enlargement, repository operation, social acceptance, land usage and the environmental burden, infrastructure and costs. The conclusions of this analysis and the special issues at Olkiluoto, namely the presence and significance of saline water at depth and the modelling of groundwater flow, are discussed. The further investigations at Olkiluoto, in particular the main aspects to consider when planning the UCRF (Underground Rock Characterisation Facility) at the site, are presented with the aim of indicating the type of work that still needs to be done in order to demonstrate that a disposal facility can be constructed

MRS system study for the repository: Yucca Mountain Site Characterization Project

International Nuclear Information System (INIS)

Sinagra, T.A.; Harig, R.

1990-12-01

The US Department of Energy (DOE), Office of Civilian Radioactive Waste Management (OCRWM), has initiated a waste management system study to identify the impacts of the presence or absence of a monitored retrievable storage facility (hereinafter referred to as ''MRS'') on system costs and program schedules. To support this study, life-cycle cost estimates and construction schedules have been prepared for the surface and underground facilities and operations geologic nuclear waste repository at Yucca Mountain, Nye County, Nevada. Nine different operating scenarios (cases) have been identified by OCRWM for inclusion in this study. For each case, the following items are determined: the repository design and construction costs, operating costs, closure and decommissioning costs, required staffing, construction schedules, uncertainties associated with the costs and schedules, and shipping cask and disposal container throughputs. This document contains A-D

MRS system study for the repository: Yucca Mountain Site Characterization Project

International Nuclear Information System (INIS)

Sinagra, T.A.; Harig, R.

1990-12-01

The US Department of Energy (DOE), Office of Civilian Radioactive Waste Management (OCRWM), has initiated a waste management system study to identify the impacts of the presence or absence of a monitored retrievable storage facility (hereinafter referred to as ''MRS'') on system costs and program schedules. To support this study, life-cycle cost estimates and construction schedules have been prepared for the surface and underground facilities and operations of a geologic nuclear waste repository at Yucca Mountain, Nye County, Nevada. Nine different operating scenarios (cases) have been identified by OCRWM for inclusion in this study. For each case, the following items are determined: the repository design and construction costs, operating costs, closure and decommissioning costs, required staffing, construction schedules, uncertainties associated with the costs and schedules, and shipping cask and disposal container throughputs. 6 refs., 83 figs., 57 tabs

Safeguards for geological repositories

International Nuclear Information System (INIS)

Fattah, A.

2000-01-01

Direct disposal of spent nuclear fuel in geological repositories is a recognised option for closing nuclear fuel cycles. Geological repositories are at present in stages of development in a number of countries and are expected to be built and operated early next century. A State usually has an obligation to safely store any nuclear material, which is considered unsuitable to re-enter the nuclear fuel cycle, isolated from the biosphere. In conjunction with this, physical protection has to be accounted for to prevent inadvertent access to such material. In addition to these two criteria - which are fully under the State's jurisdiction - a third criterion reflecting international non-proliferation commitments needs to be addressed. Under comprehensive safeguards agreements a State concedes verification of nuclear material for safeguards purposes to the IAEA. The Agency can thus provide assurance to the international community that such nuclear material has been used for peaceful purposes only as declared by the State. It must be emphasised that all three criteria mentioned constitute a 'unit'. None can be sacrificed for the sake of the other, but compromises may have to be sought in order to make their combination as effective as possible. Based on comprehensive safeguards agreements signed and ratified by the State, safeguards can be terminated only when the material has been consumed or diluted in such a way that it can no longer be utilised for any nuclear activities or has become practicably irrecoverable. As such safeguards for nuclear material in geological repositories have to be continued even after the repository has been back-filled and sealed. The effective application of safeguards must assure continuity-of-knowledge that the nuclear material in the repository has not been diverted for an unknown purpose. The nuclear material disposed in a geological repository may eventually have a higher and long term proliferation risk because the inventory is

Encapsulation plant preliminary design, phase 2. Repository connected facility

International Nuclear Information System (INIS)

Kukkola, T.

2006-12-01

The disposal facility of the spent nuclear fuel will be located in Olkiluoto. The encapsulation plant is a part of the disposal facility. In this report, an independent encapsulation plant is located above the underground repository. In the encapsulation plant, the spent fuel is received and treated for disposal. In the fuel handling cell, the spent fuel assemblies are unloaded from the spent fuel transport casks and loaded into the disposal canisters. The gas atmosphere of the disposal canister is changed, the bolted inner canister lid is closed, and the electron beam welding method is used to close the lid of the outer copper canister. The disposal canisters are cleaned and transferred into the buffer store after the machining and inspection of the copper lid welds. From the buffer store, the disposal canisters are transferred into the repository spaces by help of the canister lift. All needed stages of operation are to be performed safely without any activity releases or remarkable personnel doses. The bentonite block interim storage is associated with the encapsulation plant. The bentonite blocks are made from bentonite powder. The bentonite blocks are used as buffer material around the disposal canister in the deposition hole. The average production rate of the encapsulation plant is 40 canisters per year. The nominal maximum production capacity is 100 canisters per year in one shift operation. (orig.)

Identification of structures, systems, and components important to safety at the potential repository at Yucca Mountain

International Nuclear Information System (INIS)

Hartman, D.J.; Miller, D.D.; Klamerus, L.J.

1991-10-01

This study recommends which structures, systems, and components of the potential repository at Yucca Mountain are important to safety. The assessment was completed in April 1990 and uses the reference repository configuration in the Site Characterization Plan Conceptual Design Report and follows the methodology required at that time by DOE Procedure AP6.10-Q. Failures of repository items during the preclosure period are evaluated to determine the potential offsite radiation doses and associated probabilities. Items are important to safety if, in the event they fail to perform their intended function, an accident could result which causes a dose commitment greater than 0.5 rem to the whole body or any organ of an individual in an unrestricted area. This study recommends that these repository items include the structures that house spent fuel and high-level waste, the associated filtered ventilation exhaust systems, certain waste- handling equipment, the waste containers, the waste treatment building structure, the underground waste transporters, and other items listed in this report. This work was completed April 1990. 27 refs., 7 figs., 9 tabs

Record of responses to public comments on proposed general guidelines for recommendation of sites for nuclear waste repositories

International Nuclear Information System (INIS)

1983-01-01

The Nuclear Waste Policy Act of 1982 (Public Law 97-425, referred to in this document as the Act) assigned to the US Department of Energy (DOE) the authority for the disposal of high-level radioactive waste and spent nuclear fuel. Among other provisions, the Act specifies a process and schedule for the siting of two geologic repositories for this purpose. The Act requires that the DOE issue general guidelines for the recommendation of sites for repositories. The guidelines are to be developed in consultation with three Federal agencies (the Council on Environmental Quality, the US Environmental Protection Agency, and the US Geological Survey) and with interested Governors and issued with the concurrence of the US Nuclear Regulatory Commission. To meet this directive, the DOE convened a task force of program experts to develop proposed guidelines, issued the proposed guidelines on February 7, 1983, and invited comments from the specified Federal agencies, interested Governors, and the general public. Public hearings on the proposed guidelines were held in March at the following locations: Chicago, New Orleans, Washington, DC, Salt Lake City, and Seattle. After considering the resulting comments and preparing responses to them, the task force prepared a draft of this comment-response document and a set of alternative guidelines; these documents were issued on May 27, 1983. This document summarizes the record of comments that directly led to the alternative guidelines of May 27, 1983. It contains synopses of comments, presents the responses of the task force to the comments, and briefly describes how the proposed guidelines of February 7, 1983, were revised to produce the alternative guidelines of May 27, 1983. 13 references

Airborne microorganisms cultivable on naturally ventilated document repositories of the National Archive of Cuba.

Science.gov (United States)

Borrego, Sofía; Perdomo, Ivette

2016-02-01

The quality of the indoor air can provide very useful information for the artwork conservation. The aim of the study was to evaluate the microbial concentration inside six document repositories of the National Archive of the Republic of Cuba in two months of 1 year. The repositories are large, high, and have a natural cross-ventilation system. The microbial sampling was done in July 2010 (summer or rainy month) and February 2011 (winter or dry month) using the SAS Super 100 biocollector at 100 L/min. An appropriate selective culture media were used to isolate fungi and bacteria. A high total microbial concentration on the north side of the building in two studied months was observed. The fungal concentrations were significantly higher in July 2010 in all repositories, while the bacterial concentrations were significantly higher mostly in February 2011 only in repositories located on the first and second floor of the building. Eight fungal genera in the indoor air of all environments were isolated. Regardless of the side of the analyzed building, Penicillium, Aspergillus, and Cladosporium were the predominant genera. Aspergillus flavus and Aspergillus niger were the species isolated in almost all of the analyzed repositories in the studied months. Gram-positive bacteria prevailed among bacterial groups isolated from indoor air repositories, and some percentages corresponded to the genera Bacillus and Streptomyces. In Cuba, the temperature and relative humidity are high during the whole year but the natural ventilation plays an important role in retarding microbial growth on materials.

Analisis Konten dan Kebijakan Akses Institutional Repository

Directory of Open Access Journals (Sweden)

Amirul Ulum

2016-07-01

Abstract; Institutional repository has become a major concern of higher education in Indonesia. The number of institutional respository was increased, one of the reason is the ranking web of repositories has been conducted by the Cybermetrics Lab in 2008. At that time, many institutions started to build institutional repository in order to manage the scientific work and also trying to reach the better ranks. Meanwhile, it is an achievement of institution performance which can be promote and increase visibility for the institution. University of Surabaya has also developed the institutional repository and managed by the library. The aims of this study is to analyze the content availability and access policies defined by the University of Surabaya repository  providing services to the academic community and external users. The method used in this study by using observations of the institutional repository University of Surabaya with a literature review to clarify the analysis of the content and access policies. The results of this study indicate that the library's role is has the authority to manage the scientific work of academic community can be done through the institutional repository. However there is still need for library to be proactive to communicate regulations on mandatory deposit of scientific work and create intensive promotion of the institutional repository.

40 CFR 194.5 - Publications incorporated by reference.

Science.gov (United States)

2010-07-01

.... Nuclear Regulatory Commission, NUREG-1297 “Peer Review for High-Level Nuclear Waste Repositories... Characterization of High-Level Nuclear Waste Repositories” (excluding section 2.1 (b) and (c)); IBR approved for... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Publications incorporated by reference...

Probabilistic safety assessment for a generic deep geological repository for high-level waste and long-lived intermediate-level waste in clay

International Nuclear Information System (INIS)

Resele, G.; Holocher, J.; Mayer, G.; Hubschwerlen, N.; Niemeyer, M.; Beushausen, M.; Wollrath, J.

2010-01-01

Document available in extended abstract form only. In the selection procedure for the search of a final site location for the disposal of radioactive wastes, the comparison and evaluation of different potentially suitable repository systems in different types of host rocks will be an essential and crucial step. Since internationally accepted guidelines on how to perform such quantitative comparisons between repository systems with regard to their long-term safety behaviour are still lacking, in 2007 the German Federal Office for Radiation Protection launched the project 'VerSi' (Vergleichende Sicherheitsanalysen - Comparing Safety Assessments) that aims at the development of a methodology for the comparison of long-term safety assessments. A vital part of the VerSi project is the performance of long-term safety assessments for the comparison of two repository systems. The comparison focuses on a future repository for heat-generating, i.e. high-level and long-lived intermediate-level radioactive wastes in Germany. Rock salt is considered as a potential host rock for such a repository, and one repository system in VerSi is defined similarly to the potential site located in the Gorleben salt dome. Another suitable host rock formation may be clay. A generic location within the lower Cretaceous clays in Northern Germany is therefore chosen for the comparison of safety assessments within the VerSi project. The long-term safety assessment of a repository system for heat-generating radioactive waste at the generic clay location comprises different steps, amongst others: - Identifying the relevant processes in the near-field, in the geosphere and in the biosphere which are relevant for the long-term safety behaviour. - Development of a safety concept for the repository system. - Deduction of scenarios of the long-term evolution of the repository system. - Definition of statistic weights, i. e. the likelihood of occurrence of the scenarios. - Performance of a

Process model repositories and PNML

NARCIS (Netherlands)

Hee, van K.M.; Post, R.D.J.; Somers, L.J.A.M.; Werf, van der J.M.E.M.; Kindler, E.

2004-01-01

Bringing system and process models together in repositories facilitates the interchange of model information between modelling tools, and allows the combination and interlinking of complementary models. Petriweb is a web application for managing such repositories. It supports hierarchical process

Environmental impact statements and public consultations on the repository. An outline of SKB's planning

International Nuclear Information System (INIS)

2001-09-01

In December 2000 SKB selected three locations for further investigations as possible sites for the Swedish repository for spent nuclear fuels, Simpevarp at Oskarshamn, Forsmark at Oesthammar and Tierp. Site investigations will be performed during 5-6 years, and will provide data for a site selection. In the application for the repository commission an environmental impact statement should be included, that has been object for consultations with authorities, local communities, other organizations and the public. These consultations will take place during the whole investigation period, and will give ample possibilities for all parties to give their views and to exert an influence on the EIS

Expected brine movement at potential nuclear waste repository salt sites

International Nuclear Information System (INIS)

McCauley, V.S.; Raines, G.E.

1987-08-01

The BRINEMIG brine migration code predicts rates and quantities of brine migration to a waste package emplaced in a high-level nuclear waste repository in salt. The BRINEMIG code is an explicit time-marching finite-difference code that solves a mass balance equation and uses the Jenks equation to predict velocities of brine migration. Predictions were made for the seven potentially acceptable salt sites under consideration as locations for the first US high-level nuclear waste repository. Predicted total quantities of accumulated brine were on the order of 1 m 3 brine per waste package or less. Less brine accumulation is expected at domal salt sites because of the lower initial moisture contents relative to bedded salt sites. Less total accumulation of brine is predicted for spent fuel than for commercial high-level waste because of the lower temperatures generated by spent fuel. 11 refs., 36 figs., 29 tabs

Open DOAR the Directory of Open Access Repositories

CERN Multimedia

CERN. Geneva

2005-01-01

The last year has seen wide-spread growth in the idea of using open access repositories as a part of a research institution's accepted infrastructure. Policy development from institutions and funding bodies has also supported the growth of the repository network. The next stage of expansion will be in the provision of services and cross-repository facilities and resources. Of course, it is hoped that these will then establish a feed-back loop to encourage repository population and further repository establishment, as the potential of open access to research materials is realised. The growth of repositories has been organic, with a variety of different repositories based in departments, institutions, funding agencies or subject communities, with a range of content, both in type and subject. Existing repositories are expanding their holdings, from eprints to associated research data-sets, or with learning objects and multimedia material. This presentation will look at the development of the Directory of Open Ac...

Evaluasi Website Repositori Institusi Universitas Surabaya

Directory of Open Access Journals (Sweden)

Amirul Ulum

2015-11-01

Full Text Available The  development  of  institutional  repositories  (IRs  in Indonesia within the broader framework of open access has significant impact on preserving intellectual capital and scholarly communication. Institutional  repositories  play  a  fundamental  role  in  centralizing, preserving,  and  making  accessible  institution’s  intellectual  capital. Evaluation of the system is to determine the functionality the system to meet the users need. Using a descriptive analysis this study wants to evaluate institutional repositories of University of Surabaya. The result is usefull for institution to develop the repository systems.

Regional groundwater chemical characteristics of Aqishan pre-selected site for high level radioactive waste repository and its hydrogeological significance

International Nuclear Information System (INIS)

Guo Yonghai; Dong Jiannan; Liu Shufen; Zhou Zhichao

2014-01-01

Aqishan area located in Xinjiang Uygur Automonous Region is one of the main preselected site of disposal repository for high-level radioactive waste (HLW) in our country. Groundwater chemical feature is one of the most important consideration factors in the siting and site evaluation for high-level radioactive waste repository, From 2012 to 2013, the regional field hydrogeochemical investigation was carried out in study area and more than 30 groundwater samples were collected. According to the measurement data, the groundwater chemical features for different subareas are discussed in the paper. Furthermore, the location of discharge area of groundwater in Aqishan area was estimated according to the chemical features of different subareas. (authors)

PA/SA for Slovenian LILW repository

International Nuclear Information System (INIS)

Zeleznik, N.; Mele, I.

1999-01-01

The RAO Agency started with a new site selection procedure in 1996. As part of the preparational work for the new disposal facility, tools for assessment of the specific disposal concept influence on the environment and human has to be developed. Therefore the Slovenian assessment team that has been organized, joined the IAEAs ISAM programme, in which different approaches to performance and safety assessment were applied to safety cases. As part of the ISAM individual (national) safety cases. The RAO Agency, together with other Slovenian Inst.ions, performed the preliminary performance assessment of the Slovenian LILW repository for generic site location. The method and the results of the safety case are presented in this paper.(author)

Politics and technology in repository siting: military versus commercial nuclear wastes at WIPP 1972-1985

International Nuclear Information System (INIS)

Downey, G.L.

1985-01-01

During the 1970s, attempts by the federal government to develop a comprehensive system for disposing of nuclear wastes in geologic repositories were plagued by two related political problems; (1) whether or not military and commercial wastes should be buried together in the same repository, and (2) how to define the host state's role in the repository siting mechanism. This article explains why these two problems were connected by showing how they proved to be of decisive importance in the development of the Waste Isolation Pilot Plant (WIPP) project in Carlsbad, New Mexico. Although WIPP was initially conceived as a wholly military facility, The Department of Energy triggered a three-year dispute over the project's scope by proposing in 1978 to include commercial wastes in the repository. The key issue in the dispute concerned the political legitimacy of decision-making mechanisms for repository siting, which depend upon the extent to which they both adequately represent the interests of affected groups and meet an indistinct technical/political criterion of acceptable safety. DOE's ill-fated proposal to mix military and commercial disposal at WIPP demonstrated that the two rely on somewhat different conditions for their legitimacy. The agency overlapped the legitimate authorities of the federal and state governments and gave itself the hopeless task of negotiating a new boundary between them. 50 references, 3 figures

THERMAL CONDUCTIVITY OF THE POTENTIAL REPOSITORY HORIZON

Energy Technology Data Exchange (ETDEWEB)

J.E. BEAN

2004-09-27

The primary purpose of this report is to assess the spatial variability and uncertainty of bulk thermal conductivity in the host horizon for the repository at Yucca Mountain. More specifically, the lithostratigraphic units studied are located within the Topopah Spring Tuff (Tpt) and consist of the upper lithophysal zone (Tptpul), the middle nonlithophysal zone (Tptpmn), the lower lithophysal zone (Tptpll), and the lower nonlithophysal zone (Tptpln). Design plans indicate that approximately 81 percent of the repository will be excavated in the Tptpll, approximately 12 percent in the Tptpmn, and the remainder in the Tptul and Tptpln (BSC 2004 [DIRS 168370]). This report provides three-dimensional geostatistical estimates of the bulk thermal conductivity for the four stratigraphic layers of the repository horizon. The three-dimensional geostatistical estimates of matrix and lithophysal porosity, dry bulk density, and matrix thermal conductivity are also provided. This report provides input to various models and calculations that simulate heat transport through the rock mass. These models include the ''Drift Degradation Analysis, Multiscale Thermohydrologic Model, Ventilation Model and Analysis Report, Igneous Intrusion Impacts on Waste Packages and Waste Forms, Drift-Scale Coupled Processes (DST and TH Seepage) Models'', and ''Drift Scale THM Model''. These models directly or indirectly provide input to the total system performance assessment (TSPA). The main distinguishing characteristic among the lithophysal and nonlithophysal units is the percentage of large-scale (centimeters-meters) voids within the rock. The Tptpul and Tptpll, as their names suggest, have a higher percentage of lithophysae than the Tptpmn and the Tptpln. Understanding the influence of the lithophysae is of great importance to understanding bulk thermal conductivity.

Alternative measure for performance of HLW geologic repository

International Nuclear Information System (INIS)

Joonhang, Ahn; Chambre, P.L.

2001-01-01

A repository performance model that can show effects of canister multiplicity and repository configuration has been developed. Masses of a radionuclide in the repository and in the far field are proposed as performance measures. Canister multiplicity has significant effects on the release of long-lived radionuclides from the repository. As more canisters are included in the same water stream, the radionuclide concentration in the stream increases, but becomes independent of the number of canisters for sufficiently many canisters. Effects of reduction of radionuclide mass in the repository on the repository performance are clearly observed if the canister multiplicity is taken into account and the mass-based measures are applied. (author)

Accelerator Physics Code Web Repository

CERN Document Server

Zimmermann, Frank; Bellodi, G; Benedetto, E; Dorda, U; Giovannozzi, Massimo; Papaphilippou, Y; Pieloni, T; Ruggiero, F; Rumolo, G; Schmidt, F; Todesco, E; Zotter, Bruno W; Payet, J; Bartolini, R; Farvacque, L; Sen, T; Chin, Y H; Ohmi, K; Oide, K; Furman, M; Qiang, J; Sabbi, G L; Seidl, P A; Vay, J L; Friedman, A; Grote, D P; Cousineau, S M; Danilov, V; Holmes, J A; Shishlo, A; Kim, E S; Cai, Y; Pivi, M; Kaltchev, D I; Abell, D T; Katsouleas, Thomas C; Boine-Frankenheim, O; Franchetti, G; Hofmann, I; Machida, S; Wei, J

2006-01-01

In the framework of the CARE HHH European Network, we have developed a web-based dynamic acceleratorphysics code repository. We describe the design, structure and contents of this repository, illustrate its usage, and discuss our future plans, with emphasis on code benchmarking.

ACCELERATION PHYSICS CODE WEB REPOSITORY.

Energy Technology Data Exchange (ETDEWEB)

WEI, J.

2006-06-26

In the framework of the CARE HHH European Network, we have developed a web-based dynamic accelerator-physics code repository. We describe the design, structure and contents of this repository, illustrate its usage, and discuss our future plans, with emphasis on code benchmarking.

Global nuclear waste repository proposal highlights Australia`s nuclear energy vacuum

Energy Technology Data Exchange (ETDEWEB)

Anon.

1999-06-01

The Pangea proposal is disscused and considered relevant to Australia. A five-year research program by the company has identified Australia and Argentina as having the appropriate geological, economic and democratic credentials for such a deep repository, with Australia being favoured. A deep repository would be located where the geology has been stable for several hundred million years, so that there need not be total reliance on a robust engineered barrier system to keep the waste securely isolated for thousands of years. It would be a commercial undertaking and would have dedicated port and rail infrastructure. It would take spent fuel and other wastes from commercial reactors, and possibly also waste from weapons disposal programs. Clearly, while the primary ethical and legal principle is that each country is entirely responsible for its own waste, including nuclear waste (polluter pays etc), the big question is whether the concept of an international waste repository is acceptable ethically. Political and economic questions are secondary to this. By taking a fresh look at the reasons for the difficulties which have faced most national repository programs, and discarding the preconception that each country must develop its own disposal facilities, it is possible to define a class of simple, superior high isolation sites which may provide a multi-national basis for solving the nuclear waste disposal problem. The relatively small volumes of high-level wastes or spent fuel which arise from nuclear power production make shared repositories a feasible proposition. For small countries, the economies of scale which can be achieved make the concept attractive. For all countries, objective consideration of the relative merits of national and multi-national solutions is a prudent part of planning the management of long-lived radioactive wastes

A study of the feasibility of monitoring sealed geological repositories using seismic sensors

International Nuclear Information System (INIS)

Garbin, H.D.; Herrington, P.B.; Kromer, R.P.

1999-01-01

Questions have arisen regarding the applicability of seismic sensors to detect mining (re-entry) with a tunnel boring machine (TBM). Unlike cut and blast techniques of mining which produce impulsive seismic signals, the TBM produces seismic signals which are of long duration. (There are well established techniques available for detecting and locating the sources of the impulsive signals). The Yucca Mountain repository offered an opportunity to perform field evaluations of the capabilities of seismic sensors because during much of 1996, mining there was progressing with the use of a TBM. During the mining of the repository's southern branch, an effort was designed to evaluate whether the TBM could be detected, identified and located using seismic sensors. Three data acquisition stations were established in the Yucca Mountain area to monitor the TBM activity. A ratio of short term average to long term average algorithm was developed for use in detection based on the characteristics shown in the time series. For location of the source of detected signals, FK analysis was used on the array data to estimate back azimuths. The back azimuth from the 3 component system was estimated from the horizontal components. Unique features in the timing of the seismic signal were used to identify the source as the TBM. (author)

A study of the feasibility of monitoring sealed geological repositories using seismic sensors

International Nuclear Information System (INIS)

Garbin, H.D.; Herrington, P.B.; Kromer, R.P.

1997-10-01

Questions have arisen regarding the applicability of seismic sensors to detect mining (re-entry) with a tunnel boring machine (TBM). Unlike cut and blast techniques of mining which produce impulsive seismic signals, the TBM produces seismic signals which are of long duration. (There are well established techniques available for detecting and locating the sources of the impulsive signals.) The Yucca Mountain repository offered an opportunity to perform field evaluations of the capabilities of seismic sensors because during much of 1996, mining there was progressing with the use of a TBM. During the mining of the repository's southern branch, an effort was designed to evaluate whether the TBM could be detected, identified and located using seismic sensors. Three data acquisition stations were established in the Yucca Mountain area to monitor the TBM activity. A ratio of short term average to long term average algorithm was developed for use in detection based on the characteristics shown in the time series. For location of the source of detected signals, FK analysis was used on the array data to estimate back azimuths. The back azimuth from the 3 component system was estimated from the horizontal components. Unique features in the timing of the seismic signal were used to identify the source as the TBM

Consistency of Network Traffic Repositories: An Overview

NARCIS (Netherlands)

Lastdrager, E.; Lastdrager, E.E.H.; Pras, Aiko

2009-01-01

Traffc repositories with TCP/IP header information are very important for network analysis. Researchers often assume that such repositories reliably represent all traffc that has been flowing over the network; little thoughts are made regarding the consistency of these repositories. Still, for

48 CFR 227.7207 - Contractor data repositories.

Science.gov (United States)

2010-10-01

... repositories. 227.7207 Section 227.7207 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS... Computer Software and Computer Software Documentation 227.7207 Contractor data repositories. Follow 227.7108 when it is in the Government's interests to have a data repository include computer software or to...

Repository relevant testing applied to the Yucca Mountain Project

International Nuclear Information System (INIS)

Bates, J.K.; Woodland, A.B.; Wronkiewicz, D.J.; Cunnane, J.C.

1990-10-01

The tuff beds of Yucca Mountain, Nevada, are currently being investigated as a site for the disposal of high-level nuclear waste in an underground repository. If this site is found suitable, the repository would be located in the unsaturated zone above the water table, and a description of the site and the methodology of assessing the performance of the repository are described in the Site Characterization Plan (SCP). While many factors are accounted for during performance assessment, an important input parameter is the degradation behavior of the waste forms, which may be either spent fuel or reprocessed waste contained in a borosilicate glass matrix. To develop the necessary waste form degradation input, the waste package environment needs to be identified. This environment will change as the waste decays and also is a function of the repository design which has not yet been finalized. At the present time, an exact description of the waste package environment is not available. The SCP does provide an initial description of conditions that can be used to guide waste form evaluation. However, considerable uncertainty exists concerning the conditions under which waste form degradation and radionuclide release may occur after the waste package containment barriers are finally breached. The release conditions that are considered to be plausible include (1) a open-quotes bathtubclose quotes condition in which the waste becomes fully or partially submerged in water that enters the breached container and accumulates to fill the container up to the level of the breach opening, (2) a open-quotes wet dripclose quotes or open-quotes trickle throughclose quotes condition in which the waste form is exposed to dripping water that enters through the top and exits the bottom of a container with multiple holes, and (3) a open-quotes dryclose quotes condition in which the waste form is exposed to a humid air environment

Hydrothermal conditions around a radioactive waste repository

International Nuclear Information System (INIS)

Thunvik, R.; Braester, C.

1981-12-01

Numerical solutions for the hydrothermal conditions around a hard rock repository for nuclear fuel waste are presented. The objective of the present investigation is to illustrate in principle the effect of heat released from a hypothetical radioactive waste repository with regard to anisotropy in the rock permeability. Permeability and porosity are assumed to be constant or to decrease exponentially with depth. The hypothetical repository is situated below a horizontal ground surface or below the crest of a hill, and it is assumed that the water table follows the topography. Major interest in the analysis is directed towards the influence of anisotropy in the permeability on the flow patterns and travel times for water particles, being traced from the repository to the ground surface. The presented results show that anisotropy in the permeability may have a significant influence on the flow conditions around the repository and subsequently also on the travel times from the repository. (Authors)

Safety-related site characteristics - a relative comparison of the Forsmark reference areas

International Nuclear Information System (INIS)

Winberg, Anders

2010-12-01

SKB has over the years from 2002 to 2008 conducted site investigations in Forsmark and Laxemar, with associated site modeling, design and safety analysis. In mid-2009 Forsmark was selected on the basis of analysis made as site for a future repository for spent nuclear fuel. Based on defined safety-related geoscientific location factors data from Forsmark are compared in relative terms with data from a number of locations in Sweden, previously studied by SKB. The factors compared include: the rock's composition and structures, future climate evolution, rock mechanical conditions, earthquakes, groundwater flow, groundwater composition, delay of solutes, and the ability to characterize and describe the location. Past comparisons of these properties for the selected sites show that none of these sites collectively show any significant benefit over Forsmark site for a repository. This does not preclude that there may be places on the basis of an overall assessment of geoscientific location factors could be equivalent to Forsmark

Repository Closure and Sealing Approach

International Nuclear Information System (INIS)

A.T. Watkins

2000-01-01

The scope of this analysis will be to develop the conceptual design of the closure seals and their locations in the Subsurface Facilities. The design will be based on the recently established program requirements for transitioning to the Site Recommendation (SR) design as outlined by ''Approach to Implementing the Site Recommendation Baseline'' (Stroupe 2000) and the ''Monitored Geologic Repository Project Description Document'' (CRWMS M andO 1999b). The objective of this analysis will be to assist in providing a description for the Subsurface Facilities System Description Document, Section 2 and finally to document any conclusions reached in order to contribute and provide support to the SR. This analysis is at a conceptual level and is considered adequate to support the SR design. The final closure barriers and seals for the ventilation shafts, and the north and south ramps will require these openings to be permanently sealed to limit excessive air and water inflows and prevent human intrusion. The major tasks identified with closure in this analysis are: (1) Developing the overall subsurface seal layout and identifying design and operational interfaces for the Subsurface Facilities. (2) Summarizing the general site conditions and general rock characteristic with respect to seal location and describing the seal selected. (3) Identify seal construction materials, methodology of construction and strategic locations including design of the seal and plugs. (4) Discussing methods to prevent human intrusion

Annotated outline for the SCP conceptual design report: Office of Geologic Repositories

International Nuclear Information System (INIS)

1987-06-01

The Nuclear Waste Policy Act of 1982 (NWPA) requires that site characterization plans (SCPs) be submitted to the Nuclear Regulatory Commission (NRC), affected States and Indian tribes, and the general public for review and comment prior to the sinking of shafts at a candidate repository site. The SCP is also required by the NRC licensing procedures for the disposal of high-level waste. An Annotated Outline (AO) for Site Characterization Plans (OGR/B-5) has been prepared to provide DOE's standard format and guidance for preparation of SCPs. Consistent with the AO for SCPs. Chapter 6 of the SCP is to provide the requirements and references the media-specific design data base, describe the current design concepts, and discuss design information needs. In order to develop this design information, the Office of Geologic Repositories program is planning a SCP conceptual design phase as part of the overall repository design process. This phase is the first step in the design process, and the result and design can be expected to change as the program moves through the site characterization phase. The Annotated Outline which follows provides the standard format and guidance for the preparation of the SCP Conceptual Design Reports. It is considered to meet the intent of NRC's proposed Generic Technical Position philosophy contained therein. The SCP Conceptual Design Report will be the primary basis for preparation of Chapter 6 of the SCP and will be stand-alone reference document for the SCP. Appendix 1 to this Annotated Outline provides a correlation between Chapter 6 of the SCP and SCP Conceptual Design Report for the information purposes

Repository operational criteria comparative analysis

International Nuclear Information System (INIS)

Hageman, J.P.; Chowdhury, A.H.

1994-06-01

The objective of the ''Repository Operational Criteria (ROC) Feasibility Studies'' (or ROC task) was to conduct comprehensive and integrated analyses of repository design, construction, and operations criteria in 10 CFR Part 60 regulations considering the interfaces among the components of the regulations and impacts of any potential changes to those regulations. The ROC task addresses regulatory criteria and uncertainties related to the preclosure aspects of the geologic repository. Those parts of 10 CFR Part 60 that require routine guidance or minor changes to the rule were addressed in Hageman and Chowdhury, 1992. The ROC task shows a possible need for further regulatory clarity, by major changes to the rule, related to the design bases and siting of a geologic repository operations area and radiological emergency planning in order to assure defense-in-depth. The analyses, presented in this report, resulted in the development and refinement of regulatory concepts and their supporting rationale for recommendations for potential major changes to 10 CFR Pan 0 regulations

Generic Repository Concepts and Thermal Analysis for Advanced Fuel Cycles - 12477

Energy Technology Data Exchange (ETDEWEB)

Hardin, Ernest [Sandia National Laboratories, P.O. Box 5800 MS 0736, Albuquerque, NM 87185 (United States); Blink, James [Lawrence Livermore National Laboratory, P.O. Box 808, Livermore, CA 94551-0808 (United States); Carter, Joe [Savannah River National Laboratory, Savannah River Site, Aiken, SC 29808 (United States); Fratoni, Massimiliano; Greenberg, Harris; Sutton, Mark [Lawrence Livermore National Laboratory (United States); Howard, Robert [Oak Ridge National Laboratory, P.O. Box 2008, Oak Ridge, TN 37831 (United States)

2012-07-01

A geologic disposal concept for spent nuclear fuel (SNF) or high-level waste (HLW) consists of three components: waste inventory, geologic setting, and concept of operations. A set of reference geologic disposal concepts has been developed by the U.S. Department of Energy (DOE), Used Fuel Disposition campaign. Reference concepts are identified for crystalline rock, clay/shale, bedded salt, and deep borehole (crystalline basement) geologic settings. These were analyzed for waste inventory cases representing a range of waste types that could be produced by advanced nuclear fuel cycles. Concepts of operation consisting of emplacement mode, repository layout, and engineered barrier descriptions, were selected based on international progress. All of these disposal concepts are enclosed emplacement modes, whereby waste packages are in direct contact with encapsulating engineered or natural materials. Enclosed modes have less capacity to dissipate heat than open modes such as that proposed for a repository at Yucca Mountain. Thermal analysis has identified important relationships between waste package size and capacity, and the duration of surface decay storage needed to meet temperature limits for different disposal concepts. For the crystalline rock and clay/shale repository concepts, a waste package surface temperature limit of 100 deg. C was assumed to prevent changes in clay-based buffer material or clay-rich host rock. Surface decay storage of 50 to 100 years is needed for disposal of high-burnup LWR SNF in 4-PWR packages, or disposal of HLW glass from reprocessing LWR uranium oxide (UOX) fuel. High-level waste (HLW) from reprocessing of metal fuel used in a fast reactor could be disposed after decay storage of 50 years or less. For disposal in salt the rock thermal conductivity is significantly greater, and higher temperatures (200 deg. C) can be tolerated at the waste package surface. Decay storage of 10 years or less is needed for high-burnup LWR SNF in 4-PWR

What do we mean by a cold repository?

International Nuclear Information System (INIS)

Halsey, W.G.

1994-01-01

The topic of thermal loading of a potential repository at Yucca Mountain in Nevada has been the subject of intense discussion within the project technical community. While terms such as ''Hot Repository'' and ''Cold Repository'' are frequently used, they have not been clearly defined. In particular, the definition of a cold repository has remained the opinion of each individual. This has led to confusion and misunderstanding. In this paper, a number of observed definitions for a cold repository are discussed along with the technical implications, assumptions and inconsistencies. Finally, a common language is suggested

Copper corrosion under expected conditions in a deep geologic repository

International Nuclear Information System (INIS)

King, F.; Ahonen, L.; Taxen, C.; Vuorinen, U.; Werme, L.

2001-12-01

Copper has been the corrosion barrier of choice for the canister in the Swedish and Finnish, nuclear waste disposal programmes for over 20 years. During that time many studies have been carried out on the corrosion behaviour of copper under conditions likely to exist in an underground nuclear disposal repository located in he Fenno-Scandian bedrock. This review is a summary of what has been learnt about the long- term behaviour of the corrosion barrier during this period and what the implications of this knowledge are for the predicted service life of the canisters. The review is based on the existing knowledge from various nuclear waste management programs around the world and from the open literature.Various areas are considered: the expected evolution of the geochemical conditions in the groundwater and of the repository environment, the thermodynamics of copper corrosion, corrosion before and during saturation of the compacted bentonite buffer by groundwater, general and localized corrosion following saturation of the compacted bentonite buffer, stress corrosion cracking, radiation effects, the implications of corrosion on the service life of the canister, and areas for further study. Much has been learnt about the long-term corrosion behaviour of copper canisters over the past 20 years. The majority of the information reviewed here is drawn from the Swedish/Finnish and Canadian programmes. Despite differences in scientific approach, and canister and repository design, the results of these two programmes both suggest that copper provides an excellent corrosion barrier in an underground repository. The conclusion drawn from this review is that the original prediction made in 1978 of canister lifetimes exceeding 100,000 years remains valid

Copper corrosion under expected conditions in a deep geologic repository

Energy Technology Data Exchange (ETDEWEB)

King, F. [Integrity Corrosion Consulting Ltd, Calgary, Alberta (Canada); Ahonen, L. [Geological Survey of Finland, Espoo (Finland); Taxen, C. [Swedish Corrosion Inst., Stockholm (Sweden); Vuorinen, U. [VTT Chemical Technology, Espoo (Finland); Werme, L. [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)

2001-12-01

Copper has been the corrosion barrier of choice for the canister in the Swedish and Finnish, nuclear waste disposal programmes for over 20 years. During that time many studies have been carried out on the corrosion behaviour of copper under conditions likely to exist in an underground nuclear disposal repository located in he Fenno-Scandian bedrock. This review is a summary of what has been learnt about the long- term behaviour of the corrosion barrier during this period and what the implications of this knowledge are for the predicted service life of the canisters. The review is based on the existing knowledge from various nuclear waste management programs around the world and from the open literature.Various areas are considered: the expected evolution of the geochemical conditions in the groundwater and of the repository environment, the thermodynamics of copper corrosion, corrosion before and during saturation of the compacted bentonite buffer by groundwater, general and localized corrosion following saturation of the compacted bentonite buffer, stress corrosion cracking, radiation effects, the implications of corrosion on the service life of the canister, and areas for further study. Much has been learnt about the long-term corrosion behaviour of copper canisters over the past 20 years. The majority of the information reviewed here is drawn from the Swedish/Finnish and Canadian programmes. Despite differences in scientific approach, and canister and repository design, the results of these two programmes both suggest that copper provides an excellent corrosion barrier in an underground repository. The conclusion drawn from this review is that the original prediction made in 1978 of canister lifetimes exceeding 100,000 years remains valid.

Copper corrosion under expected conditions in a deep geologic repository

Energy Technology Data Exchange (ETDEWEB)

King, F.; Ahonen, L.; Taxen, C.; Vuorinen, U.; Werme, L

2002-01-01

Copper has been the corrosion barrier of choice for the canister in the Swedish and Finnish, nuclear waste disposal programmes for over 20 years. During that time many studies have been carried out on the corrosion behaviour of copper under conditions likely to exist in an underground nuclear disposal repository located in the Fenno-Scandian bedrock. This review is a summary of what has been learnt about the long-term behaviour of the corrosion barrier during this period and what the implications of this knowledge are for the predicted service life of the canisters. The review is based on the existing knowledge from various nuclear waste management programs around the world and from the open literature. Various areas are considered: the expected evolution of the geochemical conditions in the groundwater and of the repository environment, the thermodynamics of copper corrosion, corrosion before and during saturation of the compacted bentonite buffer by groundwater, general and localized corrosion following saturation of the compacted bentonite buffer, stress corrosion cracking, radiation effects, the implications of corrosion on the service life of the canister, and areas for further study. Much has been learnt about the long-term corrosion behaviour of copper canisters over the past 20 years. The majority of the information reviewed here is drawn from the Swedish/Finnish and Canadian programmes. Despite differences in scientific approach, and canister and repository design, the results of these two programmes both suggest that copper provides an excellent corrosion barrier in an underground repository. The conclusion drawn from this review is that the original prediction made in 1978 of canister lifetimes exceeding 100,000 years remains valid. (orig.)

Preconceptual systems and equipment for plugging of man-made accesses to a repository in basalt

International Nuclear Information System (INIS)

Taylor, C.L.; O'Rourke, J.E.; Allirot, D.; O'Connor, K.

1980-09-01

This report presents results of a study leading to preconceptual designs for plugging boreholes, shafts, and tunnels to a nuclear waste repository in basalt. Beginning design criteria include a list of preferred plug materials and plugging machines that were selected to suit the environmental conditions, and depths, diameters, and orientations of the accesses to a nuclear waste repository in the Columbia River basalts located in eastern Washington State. The environmental conditions are described. The fiscal year 1979-1980 Task II work is presented in two parts: preliminary testing of materials for plugging of man-made accesses to a repository in basalt (described in a separate report); and preconceptual systems and equipment for plugging of man-made accesses to a repository in basalt (described in this report). To fulfill the scope of the Task II work, Woodward-Clyde Consultants (WCC) was requested to: provide preconceptual systems for plugging boreholes, tunnels, and shafts in basalt; describe preconceptual borehole plugging equipment for placing the selected materials in man-made accesses; utilize the quality assurance program, program plan and schedule, and work plans previously developed for Task II; and prepare a preliminary report

Advance payments on the cost of the federal repository for radioactive waste

Energy Technology Data Exchange (ETDEWEB)

Strabburg, W

1979-03-01

Under W. Germany's Atomic Energy Act, the federal government is responsible for the final storage of radioactive wastes. Other steps of the back end fuel cycle must be implemented by private industry. Under the act, the government is entitled to charge for the costs of the erection and operation of any final repositories. To cover the initial investment involved in preparation and planning, the government is requesting advance payments from those wishing to use the repositories in the future. However, there is no legal basis for advance payments to be made, at least until an operating permit has been granted for the planned back-end fuel cycle center. Utilities operating nuclear power plants cannot be forced to make advance storage payments, and even an amendment to the Atomic Energy Act will not change the situation. (in German) (15 references)

Site selection - location of the repository for spent nuclear fuel; Platsval - lokalisering av slutfoervaret foer anvaent kaernbraensle

Energy Technology Data Exchange (ETDEWEB)

2010-12-15

This document describes the localization work and SKB's choice of site for the repository. Furthermore, SKB's basis and rationale for the decisions taken during the work are reported. The document is Appendix PV of applications under the Nuclear Activities Act and the Environmental Code to both build and operate an encapsulation plant adjacent to the central interim storage facility for spent nuclear fuel in Oskarshamn, and to construct and operate a disposal facility for spent nuclear fuel at Forsmark in Oesthammar municipality

Establishing a site for A Slovenian LILW repository - 16151

International Nuclear Information System (INIS)

VIRSEK, SANDI; SPILER, JANJA; VESELIC, MIRAN

2009-01-01

In this paper we will describe the practice and siting process for a LILW repository in Slovenia. Slovenia is a small country, and, consequently, its nuclear programme is small. It does include almost everything that large programmes have, but we still do not have a repository. In 2004, the Slovenian Radwaste management agency (ARAO) initiated a new procedure to find a proper location for a LILW repository. ARAO asked all Slovenian communities to participate. All communities have the option to withdraw from the process until they have approved the site. We received eight responses, and we prepared methodologies with different parameters to evaluate all potential sites. All sites were assessed by Slovenian experts, and determinations were based on using prepared methodologies. On the basis of their expert opinions, we prepared a pre-feasibility study and chose the three most suitable sites. With these three we continued the process. After that time, one of the communities withdrew from the procedure, and another one reversed its proposed site and proposed a new one. For the third site we continued with the programme, and we prepared a feasibility study with a Strategic Environmental Impact Assessment and preliminary safety calculations for the comparison of different concepts of disposal units. If everything goes according to the plan for this site and the concept, we expect site approval in the first half of 2009. After that, we will start preparing everything necessary for building permission. (authors)

Deep repository for spent nuclear fuel. Facility description - Layout E. Spiral ramp with one operational area

International Nuclear Information System (INIS)

Pettersson, Stig; Forsgren, Ebbe; Lange, Fritz

2002-04-01

This report documents a proposal for the design of the deep repository for spent nuclear fuel. The proposal is based on the principles that were formulated in the original KBS-3 study, but has been supplemented by investigations and experience to reflect current knowledge. The purpose of the report is to provide an integrated picture of the deep repository, as a basis for SKB's other work, e.g. environmental impact assessments, transport systems, safety issues and alternative locations, and to provide a co-ordinated account of the conditions and requirements concerning all of the necessary functions in the deep repository in order to have a well functioning facility. In addition, it should be possible to use the report as: a tool in the task of achieving a co-ordinated, safe and accepted design for the facility, a basis for further planning and costing, a basis for adaptation to geographic and other conditions for the particular location, a basis for information material, both within SKB and for interested parties outside, such as public authorities, municipalities and the general public. The capacity of the deep repository has been chosen on the basis of 40 years of operation of the Swedish nuclear power reactors, which will produce approximately 9,000 tons of uranium, equivalent to approximately 4,500 canisters. The design outlined is based on theoretical analyses of functions, safety requirements, procedures etc. that can be identified during the various phases of the construction and operation of the repository. In addition, preliminary organisation and staffing plans have been drawn up, for use as the basis for planning the necessary buildings. The report gives a vision of the overall layout and function of the facility, and a proposal for the design of all individual parts of the repository. The relationships between the various parts of the repository are described, both above and below ground, as is the interplay between the part above ground and part below

Deep repository for spent nuclear fuel. Facility description - Layout E. Spiral ramp with one operational area

Energy Technology Data Exchange (ETDEWEB)

Pettersson, Stig [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Forsgren, Ebbe [SwedPower AB, Stockholm (Sweden); Lange, Fritz [Lange Art AB, Stockholm (Sweden)

2002-04-01

This report documents a proposal for the design of the deep repository for spent nuclear fuel. The proposal is based on the principles that were formulated in the original KBS-3 study, but has been supplemented by investigations and experience to reflect current knowledge. The purpose of the report is to provide an integrated picture of the deep repository, as a basis for SKB's other work, e.g. environmental impact assessments, transport systems, safety issues and alternative locations, and to provide a co-ordinated account of the conditions and requirements concerning all of the necessary functions in the deep repository in order to have a well functioning facility. In addition, it should be possible to use the report as: a tool in the task of achieving a co-ordinated, safe and accepted design for the facility, a basis for further planning and costing, a basis for adaptation to geographic and other conditions for the particular location, a basis for information material, both within SKB and for interested parties outside, such as public authorities, municipalities and the general public. The capacity of the deep repository has been chosen on the basis of 40 years of operation of the Swedish nuclear power reactors, which will produce approximately 9,000 tons of uranium, equivalent to approximately 4,500 canisters. The design outlined is based on theoretical analyses of functions, safety requirements, procedures etc. that can be identified during the various phases of the construction and operation of the repository. In addition, preliminary organisation and staffing plans have been drawn up, for use as the basis for planning the necessary buildings. The report gives a vision of the overall layout and function of the facility, and a proposal for the design of all individual parts of the repository. The relationships between the various parts of the repository are described, both above and below ground, as is the interplay between the part above ground and part

Characterization of Swelling Clays as Components of the Engineered Barrier System for Geological Repositories. Results of an IAEA Coordinated Research Project 2002-2007

International Nuclear Information System (INIS)

2013-11-01

At the request of the Member States, the IAEA coordinates research into subjects of common interest in the context of the peaceful application of nuclear technology. The coordinated research projects (CRPs) are intended to promote knowledge and technology transfer between Member States and are largely focused on subjects of prime interest to the international nuclear community. This report presents the results of a CRP carried out between 2002 and 2007 on the subject of swelling clays proposed for use as a component in the engineered barrier system (EBS) of the multibarrier concept for disposal of radioactive waste. In 2002, under the auspices of the IAEA, a number of Member States came together to form a Network of Centres of Excellence on Training in and Demonstration of Waste Disposal Technologies in Underground Research Facilities (URF Network). This network identified the general subject of the application of high swelling clays to seal repositories for radioactive waste, with specific emphasis on the isolation of high level radioactive waste from the biosphere, as being suitable for a CRP. Existing concepts for geological repositories for high level radioactive waste and spent nuclear fuel require the use of EBSs to ensure effective isolation of the radioactive waste. There are two major materials proposed for use in the EBS, swelling clay based materials and cementitious/concrete materials. These materials will be placed between the perimeter of the excavation and the waste container to fill the existing gap and ensure isolation of the waste within the canister (also referred to as a container in some EBS concepts) by supporting safety through retardation and confinement. Cementitious materials are industrially manufactured to consistent standards and are readily available in most locations and therefore their evaluation is of less value to Member States than that of swelling clays. There exists a considerable range of programme development regarding

MAJOR REPOSITORY DESIGN ISSUES

International Nuclear Information System (INIS)

JACK N. BAILEY, DWAYNE CHESTNUT, JAMES COMPTON AND RICHARD D. SNELL

1997-01-01

The Yucca Mountain Project is focused on producing a four-part viability assessment in late FY98. Its four components (design, performance assessment, cost estimate, and licensing development plan) must be consistent. As a tool to compare design and performance assessment options, a series of repository pictures were developed for the sequential time phases of a repository. The boundaries of the time phases correspond to evolution in the engineered barrier system (EBS)

Progress towards developing an international repository for radioactive waste

International Nuclear Information System (INIS)

Kurzeme, M.

2001-01-01

Pangea Resources was established to develop and promote the concept of international repositories. The concept was based on repositories located in geologically stable, flat, arid environments meeting the 'high isolation' criteria developed by Pangea Resources. The high isolation concept of Pangea Resources can be applied in various regions of the world, and these have been made public. The pilot project chosen for exploring feasibility was for an international repository in Australia. This study was in preparation for public release, when the existence of the proposal was prematurely revealed to the media. The general media and public reaction to the concept was understandably negative. However, there were also some opinion pieces reported suggesting that the concept of an international repository should be thought about seriously, before it is accepted or rejected. In addition, thoughtful reactions were received from the business and scientific communities. In particular a group of very eminent scientists, the Scientific Review Group, undertook to review independently the quality of the work done. Nevertheless, the reaction from the state and federal governments, was also negative. The Australian Government stated its policy not to permit importation or disposal of foreign nuclear waste. During the last two years Pangea Resources has been developing the technical aspects of the concept and has produced and published several scientific reports on transport, storage and disposal of radioactive materials. All the scientific studies of Pangea Resources have been reviewed by the Scientific Review Group. The work has also been presented in scientific conferences, to the media (including a dedicated television documentary) and to the public. The technical work is generic or is based on diverse potential siting areas around the world and the disposal and storage technologies studied are being broadened beyond the specific high-isolation concept. Most importantly, it has

Long-term stability of the near-field about high-level radioactive waste repository in thermo-hydro-mechanical coupling action condition

International Nuclear Information System (INIS)

Liu Yuemiao; Wang Ju; Ke Dan; Cai Meifeng

2008-01-01

It is a long-term process for the high-level radioactive waste repository, from opening, construction to end of its service. The long-term stability of the near-field is the key issue for the design of HLW repository because the opening and heat generated from the HLW. Through a nationwide investigation, Beishan area, a Gobi desert in Gansu province, is considered as a suitable candidate and GMZ bentonite deposit which located in Xinghe County, Inner Mongolia has been proposed for the supplier of buffer/backfill material for HLW geological repository in China. According to the R and D guide of high-level radioactive waste disposal in China, the 3D model of HLW repository with high-level radioactive waste, canister and buffer/backfill material is established using FLAC3D. To take into account in situ stress, geothermal gradient, groundwater, thermal relief of HLW and swelling pressure of buffer/backfill material, the evolution of temperature, stress and displacement of HLW repository under thermo-mechanical coupling, hydro-mechanical coupling and thermo-hydro-mechanical coupling conditions was analyzed respectively. The long-term stability of HLW repository in Beishan area was studied. (authors)

Report on the access to the deposition areas of the repository. Shaft or Ramp?

International Nuclear Information System (INIS)

Baeckblom, Goeran; Christiansson, Rolf; Hedin, Allan; Norman, Fredrik; Lagerstedt, Leif

2003-05-01

During year 2002, SKB launched the site-specific engineering of the repository at the Oskarshamn and Oesthammar candidate sites. A part of the ongoing engineering work is to evaluate and possibly select type of access from surface to the underground deposition areas located at a depth of some 400 to 700 metres below the surface. The project objectives are to provide a basis for comparison and to compare generic options for access routes to the underground deposition areas, to formulate preliminary Design Justification Statements for the continued site-specific engineering of access routes to the underground repository and also to describe and exemplify methodology for optimisation of the repository engineering. In consideration of the requirements of SKB, several alternative access options are explored. The main alternatives are a ramp with one or two operational areas at the surface, a ramp with parallel excavation of a blind shaft and an alternative with shafts only. A suite of objective functions were employed in the evaluation of the main alternatives relating to long-term safety, occupational safety during construction and operation, environmental impact, sustainability of natural resources, total cost, schedules, flexibility and project risks. All alternatives studied are feasible and safe, but the alternative with a spiral ramp and a blind shaft is deemed to be the most favourable option. The alternative has the highest flexibility without any tangible disadvantages related neither to long-term safety, environmental impact nor to schedules. It is an advantage that ramp traffic is drastically reduced as rock and backfilling material is transported by the skip rather than by vehicles in the ramp, thereby reducing risks of accidents and fires in the ramp. The concurrent ramp and shaft excavation also shorten the construction period with 18 months for the underground excavations. The discounted total cost is however 100 million Swedish Kronor higher for this

Characterization of Discharge Areas of Radionuclides Originating From Nuclear Waste Repositories

Science.gov (United States)

Marklund, L.; Xu, S.; Worman, A.

2009-05-01

If leakages in nuclear waste repositories located in crystalline bedrock arise, radionuclides will reach the biosphere and cause a risk of radiological impact. The extent of the radiological impact depends on in which landscape elements the radionuclides emerge. In this study, we investigate if there are certain landscape elements that generally will act as discharge areas for radionuclides leaking from subsurface deposits. We also characterize the typical properties that distinguish these areas from others. In humid regions, landscape topography is the most important driving force for groundwater flow. Because groundwater is the main transporting agent for migrating radionuclides, the topography will determine the flowpaths of leaking radionuclides. How topography and heterogeneities in the subsurface affect the discharge distribution of the radionuclides is therefore an important scope of this study. To address these issues, we developed a 3-D transport model. Our analyses are based on site-specific data from two different areas in Sweden, Forsmark, Uppland, and Oskarshamn, Småland. The Swedish Nuclear Waste Management Company (SKB) has selected these two areas as candidate areas for a deep repository of nuclear waste and the areas are currently subject to site investigations. Our results suggest that there are hot-spots in the landscape i.e. areas with high probability of receiving large amounts of radionuclides from a leaking repository of nuclear waste. The hot-spots concentrate in the sea, streams, lakes and wetlands. All these elements are found at lower elevations in the landscape. This pattern is mostly determined by the landscape topography and the locations of fracture zones. There is a relationship between fracture zones and topography, and therefore the importance of the topography for the discharge area distribution is not contradicted by the heterogeneity in the bedrock. The varieties of landscape elements which have potential for receiving

New three-dimensional far-field potential repository thermomechanical calculations

International Nuclear Information System (INIS)

Hardy, M.P.; Bai, M.; Goodrich, R.R.; Lin, M.; Carlisle, S.; Bauer, S.J.

1993-03-01

The thermomechanical effect on the exploratory ramps, drifts, and shafts as a result of high-level nuclear waste disposal is examined using a three-dimensional thermo-elastic model. The repository layout modeled is based on the use of mechanical mining of all excavations with equivalent waste emplacement areal power densities of 57 and 80 kW/acre. Predicted temperatures and stress changes for the north and south access drifts, east main drift, east-west exploratory drift, the north and south Calico Hills access ramps, the Calico Hills north-south exploratory drift, and the optional exploratory studies facility and man and materials shafts are presented for times 10, 35, 50, 100, 300, 500, 1000, 2000, 5000, and 10,000 years after the start of waste emplacement. The study indicates that the east-west exploratory drift at the repository horizon is subject to the highest thermomechanical impact because it is located closest the buried waste canisters. For most exploratory openings, the thermally induced temperatures and stresses tend to reach the maximum magnitudes at approximately 1000 years after waste emplacement

Thermal, operational, and economic aspects of repository design alternatives

International Nuclear Information System (INIS)

Closs, K.D.; Papp, R.; Bechthold, W.; Engelmann, H.J.; Hartje, B.

1989-01-01

This paper discusses how a broad spectrum of heat-generating nuclear waste types like reprocessing waste (HLW, ILW), spent LWR, and spent HTR fuel will be disposed of in a future German repository located in a salt dome. Different package and emplacement concepts for the various waste forms are feasible, ranging from pure borehole emplacement of canisters and drums to pure drift emplacement of heavily shielded casks as well as combinations of both concepts. Optimization of the whole back-end system (waste treatment, interim storage, and disposal) is performed taking into account thermal, operational, and economic aspects. From a radiological viewpoint, the drift emplacement concept is superior to all concepts in as much as the occupational dose is lowest and zero release from the casks is attainable during normal and anomalous repository operation. As far as economics are concerned, the cost of the heavily shielded casks necessary for drift emplacement contributes markedly to the overall cost of the whole back-end system. Drift emplacement can compete economically with the other concepts only if the casks are used both for interim storage and disposal

Determination of a method to inhibit technetium migration at the repository

International Nuclear Information System (INIS)

Statler, V.; Tulenko, J.; Cloke, P.

1990-01-01

The long-term migration of 99 Tc (213,000-yr half-life) must be considered when examining the disposal of spent nuclear fuel in a geologic repository. This report outlines an investigation of the effects of iron, tin, stannous chloride, copper, manganese, and vanadium as reactants added to a mixture of technetium and J-13 well water to cause technetium precipitation. The J-13 well water was chosen because it is representative of the groundwater located at Yucca Mountain. A state-of-the-art computer software package, EQ3/6, was developed at Lawrence Livermore National Laboratory and was utilized in this study to project the result when metallic iron, tin, copper, manganese, and vanadium and the compound stannous chloride are individually added to a mixture of metallic technetium and J-13 well water. The computer codes in this study indicate that the problems associated with technetium migration at the federal repository are not insurmountable if a reactant capable of producing reducing conditions to the incoming groundwater is integrated into the waste package. Further work will focus on the laboratory experimentation to validate the computer results and to determine the best materials and configurations to inhibit technetium migration at the repository

A Federated Reference Structure for Open Informational Ecosystems

Science.gov (United States)

Heinen, Richard; Kerres, Michael; Scharnberg, Gianna; Blees, Ingo; Rittberger, Marc

2016-01-01

The paper describes the concept of a federated ecosystem for Open Educational Resources (OER) in the German education system. Here, a variety of OER repositories (ROER) (Muuß-Merholz & Schaumburg, 2014) and reference platforms have been established in the recent past. In order to develop this ecosystem, not only are metadata standards…

Kincardine deep geologic repository proposal and the public

International Nuclear Information System (INIS)

Squire, T.

2005-01-01

'Full text:' In 2002, the Municipality of Kincardine and OPG signed a Memorandum of Understanding (MOU) regarding the long-term management of low and intermediate level radioactive wastes. The purpose of the MOU was for OPG, in consultation with Kincardine, to develop a plan for the long-term management of low and intermediate level waste at OPG's Western Waste Management Facility (WWMF) located on the Bruce site. An independent assessment, which included geotechnical feasibility and safety analyses, a community attitude survey and interviews with local residents, businesses and tourists, and economic modeling to determine the potential benefits and impacts, was completed in February 2004. Ultimately, Kincardine Council endorsed a resolution (Kincardine Council no. 2004-232) to: 'endorse the opinion of the Nuclear Waste Steering Committee and select the 'Deep Rock Vault' option as the preferred course of study in regards to the management of low and intermediate level radioactive waste'. The surrounding municipalities of Saugeen Shores, Brockton, Arran-Elderslie, and Huron-Kinloss expressed their support for the Deep Geologic Repository proposal. This presentation discusses the history, major steps and public processes surrounding the Kincardine Deep Geologic Repository proposal. (author)

Parameters and criteria influencing the selection of waste emplacement configurations in mined geologic repositories

International Nuclear Information System (INIS)

Bechthold, W.; Closs, K.D.; Papp, R.

1988-01-01

Reference concepts for repositories in deep geological formations have been developed in several countries. For these concepts, emplacement configurations vary within a wide range that comprises drift emplacement of unshielded or self-shielded packages and horizontal or vertical borehole emplacement. This is caused by different parameters, criteria, and criteria weighting factors. Examples for parameters are the country's nuclear power program and waste management policy, its geological situation, and safety requirements, examples for criteria and repository area requirements, expenditures of mining and drilling, and efforts for emplacement and, if required, retrieval. Due to the variety of these factors and their ranking in different countries, requirements for a safe, dependable and cost-effective disposal of radioactive waste can be met in various ways

Memory provisions for the Manche Surface Repository

International Nuclear Information System (INIS)

Dumont, Jean-Noel; Espiet-Subert, Florence

2015-01-01

The French La Manche repository site received its last radioactive waste package in 1994. In 2003, the official surveillance phase of the closed repository started under the supervision of Andra (the national industrial operator), the French Nuclear Safety Authority (ASN) and society (e.g. the local municipalities). Florence Espiet explained that information on the existence of the repository, its content, how it was operated and how it works needs to be preserved. It also is planned to review the information periodically for a minimum of 300 years. She described the creation of two documents on memory (a detailed and a summary one), both on permanent paper, and the preservation of the land registration. The latter constitutes 'passive' provisions for preserving memory. In addition, a number of 'active' provisions are and will be put in place: guided visits, exhibitions, partnerships with organisations dealing with memory preservation, and the creation of a think tank. The latter consists of local citizens and politicians, retired employees from Andra and artists that meet several times a year and reflect on memory preservation from the perspective of, for instance, local history, education, arts and rituals. Finally, two types of markers will be used to preserve the repository's memory: i) three herbaria cataloguing the plants growing on the site of the repository, including a very short description of the repository, will be stored at different sites in France; ii) a stele indicating the main characteristics of the repository, potentially linked to an art work, will be erected at the repository

Thermal analyses of KBS-3H type repository

International Nuclear Information System (INIS)

Ikonen, K.

2003-12-01

This report contains the temperature dimensioning of the KBS-3H type nuclear fuel repository, where the fuel canisters are disposed at horizontal position in the horizontal tunnels according to the preliminary SKB (Swedish Nuclear Fuel and Waste Management Co) and Posiva plan. The maximum temperature on the canister surface is limited to the design temperature of +100 deg C. However, due to uncertainties in thermal analysis parameters (like scattering in rock conductivity) the allowable calculated maximum canister temperature is set to 90 deg C causing a safety margin of 10 deg C. The allowable temperature is controlled by adjusting the space between adjacent canisters, adjacent tunnels and the distance between separate panels of the repository and the pre-cooling time affecting power of the canisters. With reasonable canister and tunnel spacing the maximum temperature 90 deg C is achieved with an initial canister power of 1700 W. It became apparent that the temperature of canister surfaces can be determined by superposing analytic line heat source models much more efficiently than by numerical analysis, if the analytic model is first verified and calibrated by numerical analysis. This was done by comparing the surface temperatures of the central canister in a single infinite canister queue calculated numerically and analytically. In addition, the results from SKB analysis were used for comparison and for confirming the calculation procedure. For the Olkiluoto repository a reference case of one panel having 1500 canisters was analysed. The canisters are disposed in a rectangular geometry in a certain order. The calculation was performed separately for both Olkiluoto BWR canisters and Loviisa PWR canisters. The result was the minimum allowable spacing between canisters. (orig.)

Calculation of fluxes through a repository caused by a local well

International Nuclear Information System (INIS)

Thunvik, R.

1983-05-01

The purpose of the present study is to roughly estimate the ground water flux through a radioactive repository in relation to the flux into a local well under various conditions. The well is assumed to be located at a depth of either 60 or 200 metres below the ground surface. Two main settings are considered, in one the well is located in a vertical fracture zone at a distance of 100 metres from one of the outer edges of the repository. The withdrawal from the well is assumed to be 6 m 3 /day. The flow domain is characterized by a rather low permeability. The boundary conditions considered are either a continuously saturated upper boundary and impervious lateral boundaries, or a phreatic upper boundary and hydrostatic lateral boundaries. The ratio of the flux through the repository to the flux into the well was obtained to be in the range from about 10- 5 to 10- 3 , depending on the boundary conditions and the depth of the well. The lowest figures were obtained in the examples, in which the upper boundary was assumed to be continually saturated. It is concluded that these examples may be considered representative of the actual flow problem. This conclusion is based upon the fact that in the case of a phreatic boundary the drawdown caused by the well was very small and the flow responses were very slow, implying that rather a small infiltration rate is requied to maintain saturated conditions at the upper boundary. The regional gradients caused by the well were rather small in comparison with the typically naturally occurring gradients. The flow to the well will therefore have little influence on the regional flow pattern in most practical cases. (author)

DOE/OBES/Geosciences initiative on radioactive-waste isolation in mined repositories

International Nuclear Information System (INIS)

1983-05-01

The Geosciences Program within the Office of Basic Energy Sciences supports fundamental research of scientific importance and of technological relevance in the energy field. The present document describes an ongoing scientific effort on the geoscience aspects of the emplacement of radioactive waste in a mined repository. Basic research in geochemical transport, rock mechanics, geodynamics and hydrologic modelings is needed to improve understanding of geoscience processes influenced by the introduction of mechanical and thermal stresses and by the introduction of new chemical and radioactive species to the subsurface. Laboratory and in-situ data are required for scaling, modeling, and predicting parameters most relevant to locating, developing, constructing, and operating geologic radioactive waste repositories. Testing and development of high resolution surface and borehole geophysical methods are needed for subsurface characterization. Special emphasis is given to the role of fractures because they control flow and are sites for geochemical interactions

Effects of gaseous radioactive nuclides on the design and operation of repositories for spent LWR fuel in rock salt

International Nuclear Information System (INIS)

Jenks, G.H.

1979-12-01

Information relating to the identities and amounts of gaseous radionuclides present in spent LWR fuel and to their release from canistered spent fuel under plausible storage and disposal conditions was assembled, reviewed, and analyzed. Information was also reviewed and analyzed on several other subjects that relate to the integrity of the carbon steel canister in which the spent fuel is to be encapsulated and to the expected rates of transfer of gaseous radionuclides through crushed salt backfill within a disposal room in a reference repository in rock salt. The advantages and disadvantages were considered for several different canister-backfill materials, and recommendations were made regarding preferred materials. Other recommendations relate to encapsulation procedures and specifications and to needs for additional experimental studies. The objective of this work was to provide reference information, conclusions, and recommendations that could be used to establish design and operating conditions and procedures for a bedded salt repository for spent LWR fuel and that could also be used to help evaluate the safety of the repository. The results of this work will also generally apply to spent fuel repositories in domal salt. However, because the domal salt may have little or no brine inclusions within it, there may be little or no possibility that brine will migrate into open spaces around an emplaced canister. Addordingly, some of the concerns that result from the possible occurrence of brine migration in bedded salt may be of no importance in domal salt

Safety case for license application for a final repository: The French example

International Nuclear Information System (INIS)

Boissier, Fabrice; Voinis, Sylvie

2014-01-01

The reversible repository in a deep geological formation is the French reference solution for the long-term management of high-level and intermediate-level long-lived radioactive waste (HLW and ILW). Twenty years of R and D work and conceptual and basic studies since the first French Act of 1991 led, in particular, to a feasibility demonstration in 2005. According to the French Act on Radioactive Waste of 28 of June 2006, Andra shall design a reversible repository in order to apply for license in 2015. In response to this demand, Andra developed the industrial project known as 'Cigeo', a reversible geological disposal facility for HLW and ILW located in Meuse/Haute-Marne. Two years before applying for authorisation, Andra's project is now focusing on three main targets: developing Cigeo's industrial design, preparing the authorisation process through increased exchanges with stakeholders and the preparation of a safety case to support authorisation application. The latter draws on the previous safety cases of 2005 and 2009, which give a sound basis to assess Cigeo's safety, both for the operational and post-closure periods. In this new stage of the project, the challenging issues for the preparation of the safety case are the following: - to identify the various regulatory frameworks (nuclear and non-nuclear) and guides applicable to the facility; - to ensure that the industrial design complies in particular with the safety requirements as presented in the safety case and its supporting safety assessment; - to identify crucial inputs (R and D, tests,...) needed to support the authorisation application, in particular, to bring convincing arguments to assess the technical feasibility of the design and when appropriate its ability to meet the safety requirements; - to ensure that all the requirements from previous regulatory and peer reviews (national and international?) are taken into account. (authors)

Managing the nation's nuclear waste. Site descriptions: Cypress Creek, Davis Canyon, Deaf Smith, Hanford Reference, Lavender Canyon, Richton Dome, Swisher, Vacherie Dome, and Yucca Mountain

International Nuclear Information System (INIS)

1985-01-01

In 1982, the Congress enacted the Nuclear Waste Policy Act (Public Law 97-425), which established a comprehensive national program directed toward siting, constructing, and operating geologic repositories for the permanent disposal of high-level radioactive waste. In February 1983, the United States Department of Energy (DOE) identified the nine referenced repository locations as potentially acceptable sites for a mined geologic repository. These sites have been evaluated in accordance with the DOE's General Guidelines for the Recommendation of Sites for Nuclear Waste Repositories. The DOE findings and determinations are based on the evaluations contained in the draft Environmental Assessments (EA). A final EA will be prepared after considering the comments received on the draft EA. The purpose of this document is to provide the public with specific site information on each potential repository location

Performance assessment for Nuclear Power Plant Krsko intermediate and low-level rad-waste repository; Provjera sigurnosnih performansi odlagalishta radioaktivnog otpada niske i srednje aktivnosti nuklearne elektrane Krsko

Energy Technology Data Exchange (ETDEWEB)

Jelavic, V [Inst. za Elektroprivredu, Zagreb. (Yugoslavia).; Tankosic, Dj [Bechtel Inc., San Francisco (United States); Skanata, D [Nuklearna elektrana Krshko, Krshko (Yugoslavia); Plecjas, I [Institut za Nuklearne Nauke Boris Kidric, Belgrade (Yugoslavia)

1990-07-01

Performance safety Assessment for NPP Krsko radwaste repository was performed (LLW/ILW). Shallow land and tunnel type concept were analyzed. Because it was based on two unknown referent sites, one for the shallow land concept and the other for the tunnel type, analysis was generic in nature. Scenario selecting process and consequence analysis were performed by using deterministic approach. Results for both concepts of disposal suggests that proposed NPP Krsko radwaste repository reference site and disposal technology will fully meet radiation limits imposed by the Yugoslav regulations and ICRP guidelines. (author)

Safety analysis in subsurface repositories

International Nuclear Information System (INIS)

1985-06-01

The development of mathematical models to represent the repository-geosphere-biosphere system, and the development of a structure for data acquisition, processing, and use to analyse the safety of subsurface repositories, are presented. To study the behavior of radionuclides in geosphere a laboratory to determine the hydrodynamic dispersion coefficient was constructed. (M.C.K.) [pt

How many geologic repositories will be needed

International Nuclear Information System (INIS)

Evans, T.J.; Halstead, R.J.

1987-01-01

DOE's postponement of site-specific work on the second repository program had rekindled debate over the number of geologic repositories needed for disposal of high level radioactive waste. The multiple repository approach grew out of the March, 1979 IRG report, which recommended co-disposal of civilian and defense HLW in a system of regional repositories. The multiple repository approach was adopted by DOE, and incorporated in the Nuclear Waste Policy Act passed by Congress in December, 1982. Since the late 1970's, the slower than anticipated growth of the nuclear power industry has substantially reduced earlier estimates of the amount of civilian spent fuel which will require geologic disposal. Reactors currently in operation (78.5 GWe) and reactors in the construction pipeline (28 GWe) are expected to discharge about 103,200 MTU of spent fuel by the year 2036, assuming no increase in fuel burnup rate. By the year 2020, defense high level radioactive wastes equivalent to as much as 27,000 MTU could require geologic disposal. Small amounts of high level waste from other sources will also require geologic disposal. Total disposal requirements appear to be less than 140,000 MTU. The five sites nominated for the first repository, as well as hypothetical sites in granite, the host rock under primary consideration for the second repository, all appear capable of accommodating up to 140,000 MTU

Evaluation of radiological safety assessment of a repository in a clay rock formation. Evaluacion del comportamiento y de la seguridad de un almacenamiento profundo en arcilla

Energy Technology Data Exchange (ETDEWEB)

1999-12-15

This report presents a comprehensive description of the post-closure radiological safety assessment of a repository for the spent fuel arisings resulting from the Spanish nuclear program excavated in a clay host rock formation. In this report three scenarios have been analysed in detail. The first scenario represents the normal in detail. The first scenario represents the normal evolution of the repository (Reference Scenario); and includes a set of variants to investigate the relative importance of the various repository components and examine the sensitivity of the performance to parameters variations. Two altered scenarios have also been considered: deep well construction and poor sealing of the repository. This document contains a detailed description of the repository system, the methodology adopted for the scenarios generation, the process modelling approach and the results of the consequences analysis. (Author)

Nuclear waste repository simulation experiments

International Nuclear Information System (INIS)

Rothfuchs, T.; Wieczorek, K.; Feddersen, H.K.; Staupendahl, G.; Coyle, A.J.; Kalia, H.; Eckert, J.

1986-12-01

This document is the third joint annual report on the Cooperative German-American 'Brine Migration Tests' that are in progress at the Asse salt mine in the Federal Republic of Germany (FRG). This Government supported mine serves as an underground test facility for research and development (R and D)-work in the field of nuclear waste repository research and simulation experiments. The tests are designed to simulate a nuclear waste repository to measure the effects of heat and gamma radiation on brine migration, salt decrepitation, disassociation of brine, and gases collected. The thermal mechanical behavior of salt, such as room closure, stresses and changes of the properties of salt are measured and compared with predicted behavior. This document covers the following sections: Issues and test objectives: This section presents issues that are investigated by the Brine Migration Test, and the test objectives derived from these issues; test site: This section describes the test site location and geology in the Asse mine; test description: A description of the test configuration, procedures, equipment, and instrumentation is given in this section; actual test chronology: The actual history of the test, in terms of the dates at which major activities occured, is presented in this section. Test results: This section presents the test results observed to data and the planned future work that is needed to complete the test; conclusions and recommendations: This section summarizes the conclusions derived to date regarding the Brine Migration Test. Additional work that would be useful to resolve the issues is discussed. (orig.)

Digital Repositories An investigation of best practices for content recruitment to academic digital repositories and the conditions for their livelihood

CERN Document Server

Hagen, Reidun Anette

2009-01-01

A digital repository is a web accessible database, aimed at preserving the research material of an institution or scientific community. A digital repository serves as a tool for dissemination of research material and can increase the impact of the research by making it freely accessible. Digital repositories are often mentioned as a possible aid in relation to the Open Access debate; how research material should be freely accessible to anyone, anywhere at any time. However, for a digital repository to fully unleash its potential as a crucial component of Open Access, it is reliant on the ability to successfully collect and organize content. To a large extent this involves initiating self-archiving of research material by scientists throughout the academic world. This is not a trivial task, and many current repositories are inadequate in this respect, remaining empty, unvisited shelves. This thesis explores best practices for content recruitment to digital repositories, through the review of literature, and an...

Preliminary assessment of the risk of volcanism at a proposed nuclear-waste repository in the southern Great Basin

International Nuclear Information System (INIS)

Crowe, B.M.; Carr, W.J.

1980-01-01

Volcanic hazard studies of the southern Great Basin are being conducted on behalf of the Nevada Nuclear Waste Storage Investigations program. Current work is chiefly concerned with characterizing the geology, chronology, and tectonic setting of Pliocene and Quaternary volcanism in the Nevada Test Site region, and assessing volcanic risk through consequence and probability studies, particularly with respect to a potential site in the southwestern Nevada Test Site. Young ( - 6 volcanic events per year. Based on this rate, the annual probability of disruption of a 10-km 2 repository located within a 25-km radius circle centered at Yucca Mountain, southwestern Nevada Test Site, is 10 - 8 . A larger area, 50-km radius, yields a disruption probability of 10 - 9 per year. Current tectonic zonation studies of the southern Great Basin will reduce the calculated probabilities of basaltic eruption for certain areas. 21 references, 3 figures