Tank characterization reference guide

International Nuclear Information System (INIS)

De Lorenzo, D.S.; DiCenso, A.T.; Hiller, D.B.; Johnson, K.W.; Rutherford, J.H.; Smith, D.J.; Simpson, B.C.

1994-09-01

Characterization of the Hanford Site high-level waste storage tanks supports safety issue resolution; operations and maintenance requirements; and retrieval, pretreatment, vitrification, and disposal technology development. Technical, historical, and programmatic information about the waste tanks is often scattered among many sources, if it is documented at all. This Tank Characterization Reference Guide, therefore, serves as a common location for much of the generic tank information that is otherwise contained in many documents. The report is intended to be an introduction to the issues and history surrounding the generation, storage, and management of the liquid process wastes, and a presentation of the sampling, analysis, and modeling activities that support the current waste characterization. This report should provide a basis upon which those unfamiliar with the Hanford Site tank farms can start their research

U.S. Navy Aeromedical Reference and Waiver Guide

Science.gov (United States)

2010-05-05

Passion flower) – Piper methysticum (Kava-Kava) – Psilocybe semilanceata (magic mushrooms) – Rauwolfia serpentina (Indian snakeroot) – Rauwolfia... serpentina (Indian Snakeroot) – Scilla maritima (White Squill) – Scopolia carniolica (Scopolia)* U.S. Navy Aeromedical Reference and Waiver Guide...be sedatives: – Valeriana officinalis (Valerian) – Rauwolfia serpentina (Indian snakeroot) – Atropa belladonna (Deadly Nightshade)* – Chelidonium

Two low coverage bird genomes and a comparison of reference-guided versus de novo genome assemblies.

Science.gov (United States)

Card, Daren C; Schield, Drew R; Reyes-Velasco, Jacobo; Fujita, Matthew K; Andrew, Audra L; Oyler-McCance, Sara J; Fike, Jennifer A; Tomback, Diana F; Ruggiero, Robert P; Castoe, Todd A

2014-01-01

As a greater number and diversity of high-quality vertebrate reference genomes become available, it is increasingly feasible to use these references to guide new draft assemblies for related species. Reference-guided assembly approaches may substantially increase the contiguity and completeness of a new genome using only low levels of genome coverage that might otherwise be insufficient for de novo genome assembly. We used low-coverage (∼3.5-5.5x) Illumina paired-end sequencing to assemble draft genomes of two bird species (the Gunnison Sage-Grouse, Centrocercus minimus, and the Clark's Nutcracker, Nucifraga columbiana). We used these data to estimate de novo genome assemblies and reference-guided assemblies, and compared the information content and completeness of these assemblies by comparing CEGMA gene set representation, repeat element content, simple sequence repeat content, and GC isochore structure among assemblies. Our results demonstrate that even lower-coverage genome sequencing projects are capable of producing informative and useful genomic resources, particularly through the use of reference-guided assemblies.

Two low coverage bird genomes and a comparison of reference-guided versus de novo genome assemblies

Science.gov (United States)

Card, Daren C.; Schield, Drew R.; Reyes-Velasco, Jacobo; Fujita, Matthre K.; Andrew, Audra L.; Oyler-McCance, Sara J.; Fike, Jennifer A.; Tomback, Diana F.; Ruggiero, Robert P.; Castoe, Todd A.

2014-01-01

As a greater number and diversity of high-quality vertebrate reference genomes become available, it is increasingly feasible to use these references to guide new draft assemblies for related species. Reference-guided assembly approaches may substantially increase the contiguity and completeness of a new genome using only low levels of genome coverage that might otherwise be insufficient for de novo genome assembly. We used low-coverage (~3.5–5.5x) Illumina paired-end sequencing to assemble draft genomes of two bird species (the Gunnison Sage-Grouse, Centrocercus minimus, and the Clark's Nutcracker, Nucifraga columbiana). We used these data to estimate de novo genome assemblies and reference-guided assemblies, and compared the information content and completeness of these assemblies by comparing CEGMA gene set representation, repeat element content, simple sequence repeat content, and GC isochore structure among assemblies. Our results demonstrate that even lower-coverage genome sequencing projects are capable of producing informative and useful genomic resources, particularly through the use of reference-guided assemblies.

Library of Michigan: Financial Management Reference Guide.

Science.gov (United States)

Michigan Library, Lansing.

Developed to provide library directors, staff, and board members with information for performing accounting and financial management functions, this guide answers frequently asked questions, describes common practices and processes, provides examples and suggested formats for selected financial reports, and identifies issues that may require…

Department of Energy Construction Safety Reference Guide

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

DOE has adopted the Occupational Safety and Health Administration (OSHA) regulations Title 29 Code of Federal Regulations (CFR) 1926 ``Safety and Health Regulations for Construction,`` and related parts of 29 CFR 1910, ``Occupational Safety and Health Standards.`` This nonmandatory reference guide is based on these OSHA regulations and, where appropriate, incorporates additional standards, codes, directives, and work practices that are recognized and accepted by DOE and the construction industry. It covers excavation, scaffolding, electricity, fire, signs/barricades, cranes/hoists/conveyors, hand and power tools, concrete/masonry, stairways/ladders, welding/cutting, motor vehicles/mechanical equipment, demolition, materials, blasting, steel erection, etc.

Advanced distributed simulation technology: Digital Voice Gateway Reference Guide

Science.gov (United States)

Vanhook, Dan; Stadler, Ed

1994-01-01

The Digital Voice Gateway (referred to as the 'DVG' in this document) transmits and receives four full duplex encoded speech channels over the Ethernet. The information in this document applies only to DVG's running firmware of the version listed on the title page. This document, previously named Digital Voice Gateway Reference Guide, BBN Systems and Technologies Corporation, Cambridge, MA 02138, was revised for revision 2.00. This new revision changes the network protocol used by the DVG, to comply with the SINCGARS radio simulation (For SIMNET 6.6.1). Because of the extensive changes to revision 2.00 a separate document was created rather than supplying change pages.

Crop Science. Instructor Guide [and] Student Reference. Volume 24, Numbers 5 and 6.

Science.gov (United States)

Humphrey, John Kevin

This document consists of two separately published guides for a course on crop science: an instructor's guide and a student's reference manual. Each part contains nine lessons on the following topics: (1) economic importance of crops; (2) crop uses (products and byproducts); (3) plant and seed identification; (4) certified seed and variety…

Plant Science. Instructor Guide [and] Student Reference. Volume 24, Numbers 3 and 4.

Science.gov (United States)

Humphrey, John Kevin

This document consists of two separately published guides for a course on plant science: an instructor's guide and a student's reference manual. Each part consists of eight lessons and cover the following topics: (1) importance of plants; (2) classification of plants; (3) plant growth factors; (4) weeds, diseases, insects; (5) germination; (6)…

A Reference Guide for Cryogenic Properties of Materials

Energy Technology Data Exchange (ETDEWEB)

Weisend, John G

2003-09-16

A thorough knowledge of the behavior of materials at cryogenic temperatures is critical for the design of successful cryogenic systems. Over the past 50 years, a tremendous amount of material properties at cryogenic temperatures have been measured and published. This guide lists resources for finding these properties. It covers online databases, computer codes, conference proceedings, journals, handbooks, overviews and monographs. It includes references for finding reports issued by government laboratories and agencies. Most common solids and fluids used in cryogenics are covered.

MSTS. Multiphase Subsurface Transport Simulator User`s Guide and Reference

Energy Technology Data Exchange (ETDEWEB)

Nichols, W.E.; White, M.D.

1993-05-01

This User`s Guide and Reference provides information and instructions on the use of the Multiphase Subsurface Transport Simulator (MSTS) code and the associated MSTS Graphical Input. The MSTS code is used to simulate water flow, air flow, heat transfer, and dilute species mass transport in variably saturated geologic media for one, two, or three dimensions using an integrated finite-difference numerical scheme. Any or all of these processes may be simulated in a fully coupled manner. MSTS is a two-phase, two-component code with secondary processes that include binary diffusion and vapor pressure lowering. The geologic media may be homogeneous or heterogeneous, isotropic or anisotropic, and unfractured or highly fractured. A problem geometry may be described by either Cartesian or cylindrical coordinates. MSTS is written in FORTRAN 77, following the American National Standards Institute (ANSI) standards, and is machine-independent with the exception of some time and date calls required for quality control (provisions are made in the code for relatively easy adoption to a number of machines for these calls).

Water Quality in Small Community Distribution Systems. A Reference Guide for Operators

Science.gov (United States)

The U.S. Environmental Protection Agency (EPA) has developed this reference guide to assist the operators and managers of small- and medium-sized public water systems. This compilation provides a comprehensive picture of the impact of the water distribution system network on dist...

Xyce Parallel Electronic Simulator Reference Guide Version 6.7.

Energy Technology Data Exchange (ETDEWEB)

Keiter, Eric R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Aadithya, Karthik Venkatraman [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Mei, Ting [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Russo, Thomas V. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Schiek, Richard [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sholander, Peter E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Thornquist, Heidi K. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Verley, Jason [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-05-01

This document is a reference guide to the Xyce Parallel Electronic Simulator, and is a companion document to the Xyce Users' Guide [1] . The focus of this document is (to the extent possible) exhaustively list device parameters, solver options, parser options, and other usage details of Xyce . This document is not intended to be a tutorial. Users who are new to circuit simulation are better served by the Xyce Users' Guide [1] . The information herein is subject to change without notice. Copyright c 2002-2017 Sandia Corporation. All rights reserved. Trademarks Xyce TM Electronic Simulator and Xyce TM are trademarks of Sandia Corporation. Orcad, Orcad Capture, PSpice and Probe are registered trademarks of Cadence Design Systems, Inc. Microsoft, Windows and Windows 7 are registered trademarks of Microsoft Corporation. Medici, DaVinci and Taurus are registered trademarks of Synopsys Corporation. Amtec and TecPlot are trademarks of Amtec Engineering, Inc. All other trademarks are property of their respective owners. Contacts World Wide Web http://xyce.sandia.gov https://info.sandia.gov/xyce (Sandia only) Email xyce@sandia.gov (outside Sandia) xyce-sandia@sandia.gov (Sandia only) Bug Reports (Sandia only) http://joseki-vm.sandia.gov/bugzilla http://morannon.sandia.gov/bugzilla

Y.O.O. Rock Columbia County: development of a volunteer reference guide for families, children, and youth.

Science.gov (United States)

Waibel-Duncan, Mary Katherine; Benner, Eleanor; Weeks, Meghan

2012-05-01

 Y.O.O. Rock Columbia County Youth Outreach Opportunities for Families Children, and Youth (Waibel-Duncan & Gillam, 2009) represents our nonurban county's first organized effort to systematically identify and promote awareness of volunteer and outreach opportunities for families, children, and youth. In addition to describing Y.O.O. Rock's development, this article summarizes feedback from parents, professionals, and paraprofessionals and outlines their recommendations for the second edition of the guide. Issue briefs from the Corporation for National & Community Service (2005, 2006, 2008) suggest the need for reference guides like Y.O.O. Rock insofar as they document limited volunteer and outreach opportunities for young children as well as the family's role in engaging children in service to others. This article will inform others who seek to increase families', children's, and youth's awareness of volunteer activities and outreach opportunities in their communities. © 2012 Wiley Periodicals, Inc.

MSTS Multiphase Subsurface Transport Simulator User's Guide and Reference

Energy Technology Data Exchange (ETDEWEB)

Nichols, W.E.; White, M.D.

1993-05-01

This User's Guide and Reference provides information and instructions on the use of the Multiphase Subsurface Transport Simulator (MSTS) code and the associated MSTS Graphical Input. The MSTS code is used to simulate water flow, air flow, heat transfer, and dilute species mass transport in variably saturated geologic media for one, two, or three dimensions using an integrated finite-difference numerical scheme. Any or all of these processes may be simulated in a fully coupled manner. MSTS is a two-phase, two-component code with secondary processes that include binary diffusion and vapor pressure lowering. The geologic media may be homogeneous or heterogeneous, isotropic or anisotropic, and unfractured or highly fractured. A problem geometry may be described by either Cartesian or cylindrical coordinates. MSTS is written in FORTRAN 77, following the American National Standards Institute (ANSI) standards, and is machine-independent with the exception of some time and date calls required for quality control (provisions are made in the code for relatively easy adoption to a number of machines for these calls).

Maintainability design guide

International Nuclear Information System (INIS)

Pack, R.W.

1985-01-01

The Human Factors Design Guide for Maintainability provides guidance for systematically incorporating good human factors techniques into the design of power plants. The guide describes a means of developing a comprehensive program plan to ensure compliance with the human factors approaches specified by the utility. The guide also provides specific recommendations for design practices, with examples, bases, and references. The recommendations are formatted for easy use by nuclear power plant design teams and by utility personnel involved in specification and design review. The guide was developed under EPRI research project RP2166-4 and is currently being published

Adagio 4.14 users guide.

Energy Technology Data Exchange (ETDEWEB)

Spencer, Benjamin Whiting

2009-10-01

code. For example, though both Presto and Adagio have contact functionality, the content of the chapter on contact in the two guides differs. Important references for both Adagio and Presto are given in the references section at the end of this chapter. Adagio was preceded by the codes JAC and JAS3D; JAC is described in Reference 4; JAS3D is described in Reference 5. Presto was preceded by the code Pronto3D. Pronto3D is described in References 6 and 7. Some of the fundamental nonlinear technology used by both Presto and Adagio are described in References 8, 9, and 10. Currently, both Presto and Adagio use the Exodus II database and the XDMF database; Exodus II is more commonly used than XDMF. (Other options may be added in the future.) The Exodus II database format is described in Reference 11, and the XDMF database format is described in Reference 12. Important information about contact is provided in the reference document for ACME [13]. ACME is a third-party library for contact. One of the key concepts for the command structure in the input file is a concept referred to as scope. A detailed explanation of scope is provided in Section 1.2. Most of the command lines in Chapter 2 are related to a certain scope rather than to some particular functionality.

Land-use history and contemporary management inform an ecological reference model for longleaf pine woodland understory plant communities

Science.gov (United States)

Lars A. Brudvig; John L. Orrock; Ellen I. Damschen; Cathy D. Collins; Philip G. Hahn; W. Brett Mattingly; Joseph W. Veldman; Joan L. Walker

2014-01-01

Ecological restoration is frequently guided by reference conditions describing a successfully restored ecosystem; however, the causes and magnitude of ecosystem degradation vary, making simple knowledge of reference conditions insufficient for prioritizing and guiding restoration. Ecological reference models provide further guidance by quantifying reference conditions...

Petroleum Refinery Jobs and Economic Development Impact (JEDI) Model User Reference Guide

Energy Technology Data Exchange (ETDEWEB)

Goldberg, Marshall [MRG and Associates, Nevada City, CA (United States)

2013-12-31

The Jobs and Economic Development Impact (JEDI) models, developed through the National Renewable Energy Laboratory (NREL), are user-friendly tools utilized to estimate the economic impacts at the local level of constructing and operating fuel and power generation projects for a range of conventional and renewable energy technologies. The JEDI Petroleum Refinery Model User Reference Guide was developed to assist users in employing and understanding the model. This guide provides information on the model's underlying methodology, as well as the parameters and references used to develop the cost data utilized in the model. This guide also provides basic instruction on model add-in features, operation of the model, and a discussion of how the results should be interpreted. Based on project-specific inputs from the user, the model estimates job creation, earning and output (total economic activity) for a given petroleum refinery. This includes the direct, indirect and induced economic impacts to the local economy associated with the refinery's construction and operation phases. Project cost and job data used in the model are derived from the most current cost estimations available. Local direct and indirect economic impacts are estimated using economic multipliers derived from IMPLAN software. By determining the regional economic impacts and job creation for a proposed refinery, the JEDI Petroleum Refinery model can be used to field questions about the added value refineries may bring to the local community.

RCRA corrective action ampersand CERCLA remedial action reference guide

International Nuclear Information System (INIS)

1994-07-01

This reference guide provides a side-by-side comparison of RCRA corrective action and CERCLA Remedial Action, focusing on the statutory and regulatory requirements under each program, criterial and other factors that govern a site's progress, and the ways in which authorities or requirements under each program overlap and/or differ. Topics include the following: Intent of regulation; administration; types of sites and/or facilities; definition of site and/or facility; constituents of concern; exclusions; provisions for short-term remedies; triggers for initial site investigation; short term response actions; site investigations; remedial investigations; remedial alternatives; clean up criterial; final remedy; implementing remedy; on-site waste management; completion of remedial process

Reference Guide for Teaching Selected Duty Areas from Business, Marketing and Management Occupations.

Science.gov (United States)

Rich, John H.

This reference guide was designed to assist business, marketing, and management educators in locating textbook/instructional materials for use in teaching duty areas and task lists for grades 11-14. Duty areas and task lists are matched with selected textbook/instructional publications for the secretarial, general office clerk, and information…

Presto 4.14 users guide.

Energy Technology Data Exchange (ETDEWEB)

Spencer, Benjamin Whiting

2009-10-01

, though both Presto and Adagio have contact functionality, the content of the chapter on contact in the two guides differs. Important references for both Adagio and Presto are given in the references section at the end of this chapter. Adagio was preceded by the codes JAC and JAS3D; JAC is described in Reference 4; JAS3D is described in Reference 5. Presto was preceded by the code Pronto3D. Pronto3D is described in References 6 and 7. Some of the fundamental nonlinear technology used by both Presto and Adagio are described in References 8, 9, and 10. Currently, both Presto and Adagio use the Exodus II database and the XDMF database; Exodus II is more commonly used than XDMF. (Other options may be added in the future.) The Exodus II database format is described in Reference 11, and the XDMF database format is described in Reference 12. Important information about contact is provided in the reference document for ACME [13]. ACME is a third-party library for contact. One of the key concepts for the command structure in the input file is a concept referred to as scope. A detailed explanation of scope is provided in Section 1.2. Most of the command lines in Chapter 2 are related to a certain scope rather than to some particular functionality.

Presto 4.16 users guide.

Energy Technology Data Exchange (ETDEWEB)

2010-05-01

, though both Presto and Adagio have contact functionality, the content of the chapter on contact in the two guides differs. Important references for both Adagio and Presto are given in the references section at the end of this chapter. Adagio was preceded by the codes JAC and JAS3D; JAC is described in Reference 4; JAS3D is described in Reference 5. Presto was preceded by the code Pronto3D. Pronto3D is described in References 6 and 7. Some of the fundamental nonlinear technology used by both Presto and Adagio are described in References 8, 9, and 10. Currently, both Presto and Adagio use the Exodus II database and the XDMF database; Exodus II is more commonly used than XDMF. (Other options may be added in the future.) The Exodus II database format is described in Reference 11, and the XDMF database format is described in Reference 12. Important information about contact is provided in the reference document for ACME [13]. ACME is a third-party library for contact. One of the key concepts for the command structure in the input file is a concept referred to as scope. A detailed explanation of scope is provided in Section 1.2. Most of the command lines in Chapter 2 are related to a certain scope rather than to some particular functionality.

Adagio 4.16 users guide.

Energy Technology Data Exchange (ETDEWEB)

2010-05-01

contact functionality, the content of the chapter on contact in the two guides differs. Important references for both Adagio and Presto are given in the references section at the end of this chapter. Adagio was preceded by the codes JAC and JAS3D; JAC is described in Reference 4; JAS3D is described in Reference 5. Presto was preceded by the code Pronto3D. Pronto3D is described in References 6 and 7. Some of the fundamental nonlinear technology used by both Presto and Adagio are described in References 8, 9, and 10. Currently, both Presto and Adagio use the Exodus II database and the XDMF database; Exodus II is more commonly used than XDMF. (Other options may be added in the future.) The Exodus II database format is described in Reference 11, and the XDMF database format is described in Reference 12. Important information about contact is provided in the reference document for ACME [13]. ACME is a third-party library for contact. One of the key concepts for the command structure in the input file is a concept referred to as scope. A detailed explanation of scope is provided in Section 1.2. Most of the command lines in Chapter 2 are related to a certain scope rather than to some particular functionality.

Employee Relations. A Guide and Reference Book for Those Involved or Training to Be Involved in Employee Relations in the Hotel and Catering Industry. Seventh Edition.

Science.gov (United States)

Martin, Rodney; Hayter, Roy, Ed.

This guide and reference book is designed to help those involved or training to be involved in employee relations in the hotel and catering industry. Chapter 1 attempts to define employee relations. Chapter 2 describes the institutions and parties involved in employee relations in the hotel and catering industry. The focus of chapter 3 is on…

Jobs and Economic Development Impact (JEDI) User Reference Guide: Fast Pyrolysis Biorefinery Model

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yimin [National Renewable Energy Lab. (NREL), Golden, CO (United States); Goldberg, Marshall [MRG and Associates, Nevada City, CA (United States)

2015-02-01

This guide -- the JEDI Fast Pyrolysis Biorefinery Model User Reference Guide -- was developed to assist users in operating and understanding the JEDI Fast Pyrolysis Biorefinery Model. The guide provides information on the model's underlying methodology, as well as the parameters and data sources used to develop the cost data utilized in the model. This guide also provides basic instruction on model add-in features and a discussion of how the results should be interpreted. Based on project-specific inputs from the user, the JEDI Fast Pyrolysis Biorefinery Model estimates local (e.g., county- or state-level) job creation, earnings, and output from total economic activity for a given fast pyrolysis biorefinery. These estimates include the direct, indirect and induced economic impacts to the local economy associated with the construction and operation phases of biorefinery projects.Local revenue and supply chain impacts as well as induced impacts are estimated using economic multipliers derived from the IMPLAN software program. By determining the local economic impacts and job creation for a proposed biorefinery, the JEDI Fast Pyrolysis Biorefinery Model can be used to field questions about the added value biorefineries might bring to a local community.

Locus Reference Genomic sequences: An improved basis for describing human DNA variants

KAUST Repository

Dalgleish, Raymond; Flicek, Paul; Cunningham, Fiona; Astashyn, Alex; Tully, Raymond E; Proctor, Glenn; Chen, Yuan; McLaren, William M; Larsson, Pontus; Vaughan, Brendan W; Bé roud, Christophe; Dobson, Glen; Lehvä slaiho, Heikki; Taschner, Peter EM; den Dunnen, Johan T; Devereau, Andrew; Birney, Ewan; Brookes, Anthony J; Maglott, Donna R

2010-01-01

As our knowledge of the complexity of gene architecture grows, and we increase our understanding of the subtleties of gene expression, the process of accurately describing disease-causing gene variants has become increasingly problematic. In part, this is due to current reference DNA sequence formats that do not fully meet present needs. Here we present the Locus Reference Genomic (LRG) sequence format, which has been designed for the specifi c purpose of gene variant reporting. The format builds on the successful National Center for Biotechnology Information (NCBI) RefSeqGene project and provides a single-fi le record containing a uniquely stable reference DNA sequence along with all relevant transcript and protein sequences essential to the description of gene variants. In principle, LRGs can be created for any organism, not just human. In addition, we recognize the need to respect legacy numbering systems for exons and amino acids and the LRG format takes account of these. We hope that widespread adoption of LRGs - which will be created and maintained by the NCBI and the European Bioinformatics Institute (EBI) - along with consistent use of the Human Genome Variation Society (HGVS)- approved variant nomenclature will reduce errors in the reporting of variants in the literature and improve communication about variants aff ecting human health. Further information can be found on the LRG web site (http://www.lrg-sequence.org). 2010 Dalgleish et al.; licensee BioMed Central Ltd.

Locus Reference Genomic sequences: An improved basis for describing human DNA variants

KAUST Repository

Dalgleish, Raymond

2010-04-15

As our knowledge of the complexity of gene architecture grows, and we increase our understanding of the subtleties of gene expression, the process of accurately describing disease-causing gene variants has become increasingly problematic. In part, this is due to current reference DNA sequence formats that do not fully meet present needs. Here we present the Locus Reference Genomic (LRG) sequence format, which has been designed for the specifi c purpose of gene variant reporting. The format builds on the successful National Center for Biotechnology Information (NCBI) RefSeqGene project and provides a single-fi le record containing a uniquely stable reference DNA sequence along with all relevant transcript and protein sequences essential to the description of gene variants. In principle, LRGs can be created for any organism, not just human. In addition, we recognize the need to respect legacy numbering systems for exons and amino acids and the LRG format takes account of these. We hope that widespread adoption of LRGs - which will be created and maintained by the NCBI and the European Bioinformatics Institute (EBI) - along with consistent use of the Human Genome Variation Society (HGVS)- approved variant nomenclature will reduce errors in the reporting of variants in the literature and improve communication about variants aff ecting human health. Further information can be found on the LRG web site (http://www.lrg-sequence.org). 2010 Dalgleish et al.; licensee BioMed Central Ltd.

Can Single-Reference Coupled Cluster Theory Describe Static Correlation?

Science.gov (United States)

Bulik, Ireneusz W; Henderson, Thomas M; Scuseria, Gustavo E

2015-07-14

While restricted single-reference coupled cluster theory truncated to singles and doubles (CCSD) provides very accurate results for weakly correlated systems, it usually fails in the presence of static or strong correlation. This failure is generally attributed to the qualitative breakdown of the reference, and can accordingly be corrected by using a multideterminant reference, including higher-body cluster operators in the ansatz, or allowing symmetry breaking in the reference. None of these solutions are ideal; multireference coupled cluster is not black box, including higher-body cluster operators is computationally demanding, and allowing symmetry breaking leads to the loss of good quantum numbers. It has long been recognized that quasidegeneracies can instead be treated by modifying the coupled cluster ansatz. The recently introduced pair coupled cluster doubles (pCCD) approach is one such example which avoids catastrophic failures and accurately models strong correlations in a symmetry-adapted framework. Here, we generalize pCCD to a singlet-paired coupled cluster model (CCD0) intermediate between coupled cluster doubles and pCCD, yielding a method that possesses the invariances of the former and much of the stability of the latter. Moreover, CCD0 retains the full structure of coupled cluster theory, including a fermionic wave function, antisymmetric cluster amplitudes, and well-defined response equations and density matrices.

Xyce Parallel Electronic Simulator Reference Guide Version 6.4

Energy Technology Data Exchange (ETDEWEB)

Keiter, Eric R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Mei, Ting [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Russo, Thomas V. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Schiek, Richard [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sholander, Peter E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Thornquist, Heidi K. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Verley, Jason [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Baur, David Gregory [Raytheon, Albuquerque, NM (United States)

2015-12-01

This document is a reference guide to the Xyce Parallel Electronic Simulator, and is a companion document to the Xyce Users' Guide [1] . The focus of this document is (to the extent possible) exhaustively list device parameters, solver options, parser options, and other usage details of Xyce . This document is not intended to be a tutorial. Users who are new to circuit simulation are better served by the Xyce Users' Guide [1] . Trademarks The information herein is subject to change without notice. Copyright c 2002-2015 Sandia Corporation. All rights reserved. Xyce TM Electronic Simulator and Xyce TM are trademarks of Sandia Corporation. Portions of the Xyce TM code are: Copyright c 2002, The Regents of the University of California. Produced at the Lawrence Livermore National Laboratory. Written by Alan Hindmarsh, Allan Taylor, Radu Serban. UCRL-CODE-2002-59 All rights reserved. Orcad, Orcad Capture, PSpice and Probe are registered trademarks of Cadence Design Systems, Inc. Microsoft, Windows and Windows 7 are registered trademarks of Microsoft Corporation. Medici, DaVinci and Taurus are registered trademarks of Synopsys Corporation. Amtec and TecPlot are trademarks of Amtec Engineering, Inc. Xyce 's expression library is based on that inside Spice 3F5 developed by the EECS Department at the University of California. The EKV3 MOSFET model was developed by the EKV Team of the Electronics Laboratory-TUC of the Technical University of Crete. All other trademarks are property of their respective owners. Contacts Bug Reports (Sandia only) http://joseki.sandia.gov/bugzilla http://charleston.sandia.gov/bugzilla World Wide Web http://xyce.sandia.gov http://charleston.sandia.gov/xyce (Sandia only) Email xyce@sandia.gov (outside Sandia) xyce-sandia@sandia.gov (Sandia only)

Training Requirements and Information Management System. Software user guide

Energy Technology Data Exchange (ETDEWEB)

Cillan, T.F.; Hodgson, M.A.

1992-05-01

This is the software user`s guide for the Training Requirements and Information Management System. This guide defines and describes the software operating procedures as they apply to the end user of the software program. This guide is intended as a reference tool for the user who already has an indepth knowledge of the Training Requirements and Information Management System functions and data reporting requirement.

Fluoroscopy-guided insertion of nasojejunal tubes in children - setting local diagnostic reference levels

International Nuclear Information System (INIS)

Vitta, Lavanya; Raghavan, Ashok; Sprigg, Alan; Morrell, Rachel

2009-01-01

Little is known about the radiation burden from fluoroscopy-guided insertions of nasojejunal tubes (NJTs) in children. There are no recommended or published standards of diagnostic reference levels (DRLs) available. To establish reference dose area product (DAP) levels for the fluoroscopy-guided insertion of nasojejunal tubes as a basis for setting DRLs for children. In addition, we wanted to assess our local practice and determine the success and complication rates associated with this procedure. Children who had NJT insertion procedures were identified retrospectively from the fluoroscopy database. The age of the child at the time of the procedure, DAP, screening time, outcome of the procedure, and any complications were recorded for each procedure. As the radiation dose depends on the size of the child, the children were assigned to three different age groups. The sample size, mean, median and third-quartile DAPs were calculated for each group. The third-quartile values were used to establish the DRLs. Of 186 procedures performed, 172 were successful on the first attempt. These were performed in a total of 43 children with 60% having multiple insertions over time. The third-quartile DAPs were as follows for each age group: 0-12 months, 2.6 cGy cm 2 ; 1-7 years, 2.45 cGy cm 2 ; >8 years, 14.6 cGy cm 2 . High DAP readings were obtained in the 0-12 months (n = 4) and >8 years (n = 2) age groups. No immediate complications were recorded. Fluoroscopy-guided insertion of NJTs is a highly successful procedure in a selected population of children and is associated with a low complication rate. The radiation dose per procedure is relatively low. (orig.)

Challenges and Opportunities for Transactive Control of Electric Vehicle Supply Equipment. A Reference Guide

Energy Technology Data Exchange (ETDEWEB)

Jin, Xin [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Meintz, Andrew [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2015-07-29

This report seeks to characterize the opportunities and challenges that arise in developing a transactive control strategy for grid-EVSE integration in various use-case scenarios in a way that provides end-user, energy market, grid, and societal benefits. A detailed review provides information about EVSE integration market trends and stakeholder activities. This is followed by an exploration of value proposition for transactive control of EVSE at both the home scale and the building/campus scale. This report will serve as a reference guide for stakeholders in the grid-EVSE integration area, illustrate potential implementations, and identify a high-value research project for overcoming the barriers and unlocking the benefits of transactive controls of EVSE. While it is not intended to specify the technical details of the transactive control solution, the report contains a list of use cases describing potential applications of transactive control of EVSE, barriers to implementing these applications, and research and development (R&D) opportunities to overcome the barriers. The use cases of transactive control of EVSE are listed in Table ES1.

A hybrid reference-guided de novo assembly approach for generating Cyclospora mitochondrion genomes.

Science.gov (United States)

Gopinath, G R; Cinar, H N; Murphy, H R; Durigan, M; Almeria, M; Tall, B D; DaSilva, A J

2018-01-01

Cyclospora cayetanensis is a coccidian parasite associated with large and complex foodborne outbreaks worldwide. Linking samples from cyclosporiasis patients during foodborne outbreaks with suspected contaminated food sources, using conventional epidemiological methods, has been a persistent challenge. To address this issue, development of new methods based on potential genomically-derived markers for strain-level identification has been a priority for the food safety research community. The absence of reference genomes to identify nucleotide and structural variants with a high degree of confidence has limited the application of using sequencing data for source tracking during outbreak investigations. In this work, we determined the quality of a high resolution, curated, public mitochondrial genome assembly to be used as a reference genome by applying bioinformatic analyses. Using this reference genome, three new mitochondrial genome assemblies were built starting with metagenomic reads generated by sequencing DNA extracted from oocysts present in stool samples from cyclosporiasis patients. Nucleotide variants were identified in the new and other publicly available genomes in comparison with the mitochondrial reference genome. A consolidated workflow, presented here, to generate new mitochondrion genomes using our reference-guided de novo assembly approach could be useful in facilitating the generation of other mitochondrion sequences, and in their application for subtyping C. cayetanensis strains during foodborne outbreak investigations.

Ethanol Fuels Reference Guide: A Decision-Makers Guide to Ethanol Fuels

Energy Technology Data Exchange (ETDEWEB)

1982-10-01

This guide is a compendium of information on alcohol fuel production and use. Chapter titles are: facts about ethanol; gasohol-answers to the basic questions; feedstocks and their coproducts; ethanol production processes; and vehicle fuel use and performance. In addition, there are 8 appendices which include fermentation guides for common grains and potatoes, component and enzyme manufacturers, and information on regulations and permits. (DMC)

Equine Science. Instructor Guide [and] Student Reference. Volume 27, Number 4 [and] Volume 27, Number 5.

Science.gov (United States)

Leffert, Kenneth L.; And Others

This instructor guide and the corresponding student reference contain 10 lessons to enhance an Agricultural Science I course for grade 9. The lessons cover the following topics: introduction, psychology and handling, conformation and selection, genetics and reproduction, herd health, hoof care, nutrition, equipment and facilities, handling horses,…

SQL Pocket Guide

CERN Document Server

Gennick, Jonathan

2010-01-01

If you're a programmer or database administrator who uses SQL in your day-to-day work, this popular pocket guide is the ideal on-the-job reference. You'll find many examples that address the language's complexity, along with key aspects of SQL used in IBM DB2 Release 9.7, MySQL 5.1, Oracle Database 11g Release 2, PostgreSQL 9.0, and Microsoft SQL Server 2008 Release 2. SQL Pocket Guide describes how these database systems implement SQL syntax for querying, managing transactions, and making changes to data. It also shows how the systems use SQL functions, regular expression syntax, and type c

Promotion Guide – A guide for career reviews

CERN Multimedia

Staff Association

2017-01-01

On 8 February, the Standing Concertation Committee (SCC) approved the Promotion Guide, subtitled “A guide for career reviews”. The English version is already published on the HR website. This Promotion Guide is not very different from the Career Path Guide which it replaces following the implementation of the new career structure with benchmark jobs and grades. Structure The guide is composed of three parts: Section I – Introduction revisits the reference documents: the Staff Rules and Regulations (S&R) and the Administrative Circular No. 26 (AC 26). In the Staff Rules and Regulations, the term promotion is defined as a change of grade1 and in Administrative Circular No. 26, the Promotion Guide is referenced under paragraph 452. The objective of the Promotion Guide is laid out in Section I: “The Promotion Guide defines the criteria to be used as a reference for career reviews with a view to a potential promotion”. However, this guide do...

Magnetic resonance described in the excitation dependent rotating frame of reference.

Science.gov (United States)

Tahayori, Bahman; Johnston, Leigh A; Mareels, Iven M Y; Farrell, Peter M

2008-01-01

An excitation dependent rotating frame of reference to observe the magnetic resonance phenomenon is introduced in this paper that, to the best of our knowledge, has not been used previously in the nuclear magnetic resonance context. The mathematical framework for this new rotating frame of reference is presented based on time scaling the Bloch equation after transformation to the classical rotating frame of reference whose transverse plane is rotating at the Larmor frequency. To this end, the Bloch equation is rewritten in terms of a magnetisation vector observed from the excitation dependent rotating frame of reference. The resultant Bloch equation is referred to as the time scaled Bloch equation. In the excitation dependent rotating frame of reference whose coordinates are rotating at the instantaneous Rabi frequency the observed magnetisation vector is a much slower signal than the true magnetisation in the rotating frame of reference. As a result the ordinary differential equation solvers have the ability to solve the time scaled version of the Bloch equation with a larger step size resulting in a smaller number of samples for solving the equation to a desired level of accuracy. The simulation results for different types of excitation are presented in this paper. This method may be used in true Bloch simulators in order to reduce the simulation time or increase the accuracy of the numerical solution. Moreover, the time scaled Bloch equation may be employed to determine the optimal excitation pattern in magnetic resonance imaging as well as designing pulses with better slice selectivity which is an active area of research in this field.

LCCP Desktop Application v1.0 Engineering Reference

Energy Technology Data Exchange (ETDEWEB)

Beshr, Mohamed [Univ. of Maryland, College Park, MD (United States); Aute, Vikrant [Univ. of Maryland, College Park, MD (United States)

2014-04-01

This Life Cycle Climate Performance (LCCP) Desktop Application Engineering Reference is divided into three parts. The first part of the guide, consisting of the LCCP objective, literature review, and mathematical background, is presented in Sections 2-4. The second part of the guide (given in Sections 5-10) provides a description of the input data required by the LCCP desktop application, including each of the input pages (Application Information, Load Information, and Simulation Information) and details for interfacing the LCCP Desktop Application with the VapCyc and EnergyPlus simulation programs. The third part of the guide (given in Section 11) describes the various interfaces of the LCCP code.

Guide Structures in CD-ROM Dictionaries, with Specific Reference to the EWED and the ELHAT

Directory of Open Access Journals (Sweden)

Philip Louw

2011-10-01

Full Text Available

macro- and microstructural information. In order to evaluate the methods which lexicographers employ to improve dictionary accessibility, the concept of guide structures was introduced by Hausmann and Wiegand (1989. Since the appearance of that article, various academics have written articles and read papers on guide structures in print dictionaries, but few studies have focussed on the tremendous potential of guide structures in electronic dictionaries. In this article it will be shown that electronic dictionaries add dimensions to the implementation of guide structures not possible in print versions. The role of two of the guide structures in the transfer of infonnation in CD-ROM dictionaries will be discussed. The access and mediostructures of the Microsoft Encarta World English Dictionary and the Elektroniese Handwoordeboek van die Afrikaanse Taal will be analysed and critically evaluated to illustrate the advantages of electronic dictionaries over print dictionaries and the urgent need for metalexicographical discussion of this publication medium.

Keywords: ACCESS STRUCTURE; ACTIVE CROSS-REFERENCES; CD-ROM DICTIONARY; DICTIONARY ACCESSIBILITY; ENCYCLOPAEDIC DICTIONARY; GUIDE STRUCTURES; INNER ACCESS STRUCTURE; INNER SEARCH PATH; INTERNET; MEDIOSTRUCTURE; MULTIMEDIA; OUTER ACCESS STRUCTURE; OUTER SEARCH PATH; PASSIVE CROSSREFERENCING; USER-FRIENDLINESS

Opsomming: Gidsstrukture in CD-ROM-woordeboeke, met spesifieke verwysingna EWED en ELHA T. Die sukses van modeme woordeboeke hang grootliles af vandie toeganklikheid van hulle makro- en mikrostrukturele inligting. Hausmann en Wiegand (1989het die konsep van gidsstrukture ingevoer om die metodes te evalueer wat leksikograwe gebruikom woordeboektoeganklikheid Ie verbeter. Sedert hierdie artikel verskyn het, het verskeie akademic:i artikels gepubliseer en referate gelewer oor gidsstrukture in gedrukte woordeboeke, maarmin studies het gefokus op die geweldige potensiaal van

SEE Action Guide for States: Guidance on Establishing and Maintaining Technical Reference Manuals for Energy Efficiency Measures

Energy Technology Data Exchange (ETDEWEB)

None

2017-06-01

The goal of this guide is to support the development, maintenance, and use of accurate and reliable Technical Reference Manuals (TRMs). TRMs provide information primarily used for estimating the energy and demand savings of end-use energy efficiency measures associated with utility customer-funded efficiency programs.

Asthma and Respiratory Foundation NZ child and adolescent asthma guidelines: a quick reference guide.

Science.gov (United States)

Asher, Innes; McNamara, David; Davies, Cheryl; Demetriou, Teresa; Fleming, Theresa; Harwood, Matire; Hetaraka-Stevens, Lorraine; Ingham, Tristram; Kristiansen, John; Reid, Jim; Rickard, Debbie; Ryan, Debbie

2017-12-01

The purpose of the New Zealand Child and adolescent asthma guidelines: a quick reference guide is to provide simple, practical, evidence-based recommendations for the diagnosis, assessment and management of asthma in children and adolescents in New Zealand, with the aim of improving outcomes and reducing inequities. The intended users are health professionals responsible for delivering asthma care in the community and hospital emergency department settings, and those responsible for the training of such health professionals.

RADTRAN 4: User guide

International Nuclear Information System (INIS)

Neuhauser, K.S.; Kanipe, F.L.

1992-01-01

RADTRAN 4 is used to evaluate radiological consequences of incident-free transportation, as well as the radiological risks from vehicular accidents occurring during transportation. This User Guide is Volume 3 in a series of four volume of the documentation of the RADTRAN 4 computer code for transportation risk analysis. The other three volumes are Volume 1, the Executive Summary; Volume 2, the Technical Manual; and Volume 4, the Programmer's Manual. The theoretical and calculational basis for the operations performed by RADTRAN 4 are discussed in Volume 2. Throughout this User Guide the reader will be referred to Volume 2 for detailed discussions of certain RADTRAN features. This User Guide supersedes the document ''RADTRAN III'' by Madsen et al. (1983). This RADTRAN 4 User Guide specifies and describes the required data, control inputs, input sequences, user options, program limitations, and other activities necessary for execution of the RADTRAN 4 computer code

An empirical model describing the postnatal growth of organs in ICRP reference humans: Pt. 1

International Nuclear Information System (INIS)

Walker, J.T.

1991-01-01

An empirical model is presented for describing the postnatal mass growth of lungs in ICRP reference humans. A combined exponential and logistic function containing six parameters is fitted to ICRP 23 lung data using a weighted non-linear least squares technique. The results indicate that the model delineates the data well. Further analysis shows that reference male lungs attain a higher pubertal peak velocity (PPV) and adult mass size than female lungs, although the latter reach their PPV and adult mass size first. Furthermore, the model shows that lung growth rates in infants are two to three orders of magnitude higher than those in mature adults. This finding is important because of the possible association between higher radiation risks in infants' organs that have faster cell turnover rates compared to mature adult organs. The significance of the model for ICRP dosimetric purposes will be discussed. (author)

Introduction to Animal Nutrition. Instructor Guide [and] Student Reference. Volume 28, Number 7 [and] Volume 28, Number 8.

Science.gov (United States)

Peiter, Andrea; And Others

This instructor guide and the corresponding student reference contain five lessons about animal science for inclusion in Vocational Instructional Management System (VIMS) agricultural education courses. The lessons cover these topics: the monogastric digestive system, the ruminant digestive system, the importance of meeting nutritional needs, how…

Jobs and Economic Development Impact (JEDI) Model: Offshore Wind User Reference Guide

Energy Technology Data Exchange (ETDEWEB)

Lantz, E.; Goldberg, M.; Keyser, D.

2013-06-01

The Offshore Wind Jobs and Economic Development Impact (JEDI) model, developed by NREL and MRG & Associates, is a spreadsheet based input-output tool. JEDI is meant to be a user friendly and transparent tool to estimate potential economic impacts supported by the development and operation of offshore wind projects. This guide describes how to use the model as well as technical information such as methodology, limitations, and data sources.

Description of a reference mixed oxide fuel fabrication plant (MOFFP)

International Nuclear Information System (INIS)

1978-01-01

In order to evaluate the environment impact, due to the Mixed Oxide Fuel Fabrication Plants, work has been initiated to describe the general design and operating conditions of a reference Mixed Oxide Fuel Fabrication Plant (MOFFP) for the 1990 time frame. The various reference data and basic assumptions for the reference MOFFP plant have been defined after discussion with experts. The data reported in this document are only made available to allow an evaluation of the environmental impact due to a reference MOFFP plant. These data have therefore not to be used as recommandation, standards, regulatory guides or requirements

Introduction to Animal Reproduction. Instructor Guide [and] Student Reference. Volume 28, Number 5 [and] Volume 28, Number 6.

Science.gov (United States)

Peiter, Andrea; And Others

This instructor guide and the corresponding student reference contain seven lessons about animal reproduction for inclusion in Vocational Instructional Management System (VIMS) agricultural education courses. The lessons cover the following topics: the male and female reproductive systems, puberty and the estrous cycle, conception and gestation,…

COLLABORATIVE GUIDE: A REEF MANAGER'S GUIDE TO ...

Science.gov (United States)

Innovative strategies to conserve the world's coral reefs are included in a new guide released today by NOAA, and the Australian Great Barrier Reef Marine Park Authority, with author contributions from a variety of international partners from government agencies, non-governmental organizations, and academic institutions. Referred to as A Reef Manager's Guide to Coral Bleaching, the guide will provide coral reef managers with the latest scientific information on the causes of coral bleaching and new management strategies for responding to this significant threat to coral reef ecosystems. Innovative strategies to conserve the world's coral reefs are included in a new guide released today by NOAA, and the Australian Great Barrier Reef Marine Park Authority, with author contributions from a variety of international partners from government agencies, non-governmental organizations, and academic institutions. Dr. Jordan West, of the National Center for Environmental Assessment, was a major contributor to the guide. Referred to as

Xyce Parallel Electronic Simulator Reference Guide Version 6.6.

Energy Technology Data Exchange (ETDEWEB)

Keiter, Eric R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Aadithya, Karthik Venkatraman [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Mei, Ting [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Russo, Thomas V. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Schiek, Richard [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sholander, Peter E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Thornquist, Heidi K. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Verley, Jason [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2016-11-01

This document is a reference guide to the Xyce Parallel Electronic Simulator, and is a companion document to the Xyce Users' Guide [1] . The focus of this document is (to the extent possible) exhaustively list device parameters, solver options, parser options, and other usage details of Xyce . This document is not intended to be a tutorial. Users who are new to circuit simulation are better served by the Xyce Users' Guide [1] . The information herein is subject to change without notice. Copyright c 2002-2016 Sandia Corporation. All rights reserved. Acknowledgements The BSIM Group at the University of California, Berkeley developed the BSIM3, BSIM4, BSIM6, BSIM-CMG and BSIM-SOI models. The BSIM3 is Copyright c 1999, Regents of the University of California. The BSIM4 is Copyright c 2006, Regents of the University of California. The BSIM6 is Copyright c 2015, Regents of the University of California. The BSIM-CMG is Copyright c 2012 and 2016, Regents of the University of California. The BSIM-SOI is Copyright c 1990, Regents of the University of California. All rights reserved. The Mextram model has been developed by NXP Semiconductors until 2007, Delft University of Technology from 2007 to 2014, and Auburn University since April 2015. Copyrights c of Mextram are with Delft University of Technology, NXP Semiconductors and Auburn University. The MIT VS Model Research Group developed the MIT Virtual Source (MVS) model. Copyright c 2013 Massachusetts Institute of Technology (MIT). The EKV3 MOSFET model was developed by the EKV Team of the Electronics Laboratory-TUC of the Technical University of Crete. Trademarks Xyce TM Electronic Simulator and Xyce TM are trademarks of Sandia Corporation. Orcad, Orcad Capture, PSpice and Probe are registered trademarks of Cadence Design Systems, Inc. Microsoft, Windows and Windows 7 are registered trademarks of Microsoft Corporation. Medici, DaVinci and Taurus are registered trademarks of Synopsys Corporation. Amtec and Tec

Using high-performance ¹H NMR (HP-qNMR®) for the certification of organic reference materials under accreditation guidelines--describing the overall process with focus on homogeneity and stability assessment.

Science.gov (United States)

Weber, Michael; Hellriegel, Christine; Rueck, Alexander; Wuethrich, Juerg; Jenks, Peter

2014-05-01

Quantitative NMR spectroscopy (qNMR) is gaining interest across both analytical and industrial research applications and has become an essential tool for the content assignment and quantitative determination of impurities. The key benefits of using qNMR as measurement method for the purity determination of organic molecules are discussed, with emphasis on the ability to establish traceability to "The International System of Units" (SI). The work describes a routine certification procedure from the point of view of a commercial producer of certified reference materials (CRM) under ISO/IEC 17025 and ISO Guide 34 accreditation, that resulted in a set of essential references for (1)H qNMR measurements, and the relevant application data for these substances are given. The overall process includes specific selection criteria, pre-tests, experimental conditions, homogeneity and stability studies. The advantages of an accelerated stability study over the classical stability-test design are shown with respect to shelf-life determination and shipping conditions. Copyright © 2013 The Authors. Published by Elsevier B.V. All rights reserved.

Implementing an inclusive staffing model for today's reference services a practical guide for librarians

CERN Document Server

Nims, Julia K; Stevens, Robert

2013-01-01

Reference service remains a core function of modern libraries. However, how and where we provide assistance has evolved with changing technologies and the shifting habits and preferences of our users. One way libraries can provide the on-demand, in-person assistance while managing and developing new services and resources that will benefit current and future users is to reconsider how their reference points and services are staffed and adopt a staff-based reference model. In Implementing an Inclusive Staffing Model for Today's Reference Services, Nims, Storm, and Stevens describe step-by-step

A high-temperature, high-pressure, silver-silver chloride reference electrode

International Nuclear Information System (INIS)

King, F.; Bailey, M.G.; Clarke, C.F.; Ikeda, B.M.; Litke, C.D.; Ryan, S.R.

1989-05-01

A high-temperature, high-pressure, silver-silver chloride reference electrode is described. This report is meant to serve as a user's guide to the experimentalist. Consequently, the design and construction of the electrode are dealt with in some detail. The problems that may be encountered, along with their possible causes and remedies, are also discussed. Conversion factors are given for both internal and external reference electrodes, so that measured potentials can be related to the standard hydrogen electrode scale

Automatic generation of computable implementation guides from clinical information models.

Science.gov (United States)

Boscá, Diego; Maldonado, José Alberto; Moner, David; Robles, Montserrat

2015-06-01

Clinical information models are increasingly used to describe the contents of Electronic Health Records. Implementation guides are a common specification mechanism used to define such models. They contain, among other reference materials, all the constraints and rules that clinical information must obey. However, these implementation guides typically are oriented to human-readability, and thus cannot be processed by computers. As a consequence, they must be reinterpreted and transformed manually into an executable language such as Schematron or Object Constraint Language (OCL). This task can be difficult and error prone due to the big gap between both representations. The challenge is to develop a methodology for the specification of implementation guides in such a way that humans can read and understand easily and at the same time can be processed by computers. In this paper, we propose and describe a novel methodology that uses archetypes as basis for generation of implementation guides. We use archetypes to generate formal rules expressed in Natural Rule Language (NRL) and other reference materials usually included in implementation guides such as sample XML instances. We also generate Schematron rules from NRL rules to be used for the validation of data instances. We have implemented these methods in LinkEHR, an archetype editing platform, and exemplify our approach by generating NRL rules and implementation guides from EN ISO 13606, openEHR, and HL7 CDA archetypes. Copyright © 2015 Elsevier Inc. All rights reserved.

Python essential reference

CERN Document Server

Beazley, David M

2009-01-01

Python Essential Reference is the definitive reference guide to the Python programming language — the one authoritative handbook that reliably untangles and explains both the core Python language and the most essential parts of the Python library. Designed for the professional programmer, the book is concise, to the point, and highly accessible. It also includes detailed information on the Python library and many advanced subjects that is not available in either the official Python documentation or any other single reference source. Thoroughly updated to reflect the significant new programming language features and library modules that have been introduced in Python 2.6 and Python 3, the fourth edition of Python Essential Reference is the definitive guide for programmers who need to modernize existing Python code or who are planning an eventual migration to Python 3. Programmers starting a new Python project will find detailed coverage of contemporary Python programming idioms.

Flight Test Guide (Part 61 Revised): Instrument Pilot: Helicopter.

Science.gov (United States)

Federal Aviation Administration (DOT), Washington, DC. Flight Standards Service.

The guide provides an outline of the skills required to pass the flight test for an Instrument Pilot Helicopter Rating under Part 61 (revised) of Federal Aviation Regulations. General procedures for flight tests are described and the following pilot operations outlined: maneuvering by reference to instruments, IFR navigation, instrument…

Entomology for Agricultural Science II Core Curriculum. Instructor Guide, Volume 23, Number 2, and Student Reference, Volume 23, Number 3.

Science.gov (United States)

DeFelice, Karen L.

This unit is a basic introduction to entomology. The instructor guide and the corresponding student reference contain seven lessons: (1) introduction to entomology; (2) insect collection; (3) insect identification; (4) methods of control; (5) chemical control measures; (6) safe use of insecticides; and (7) integrated pest management. Students…

Automated Circulation Systems in Libraries Serving the Blind and Physically Handicapped: A Reference Guide for Planning.

Science.gov (United States)

Wanger, Judith; And Others

Designed to facilitate communications in future automation projects between library and data processing personnel, especially those projects involving the use of automated systems in the service of disabled patrons, this guide identifies and describes a master set of major circulation system requirements and design considerations, and illustrates…

Users' guide to the positron camera DDP516 computer system

International Nuclear Information System (INIS)

Bracher, B.H.

1979-08-01

This publication is a guide to the operation, use and software for a DDP516 computer system provided by the Data Handling Group primarily for the development of a Positron Camera. The various sections of the publication fall roughly into three parts. (1) Sections forming the Operators Guide cover the basic operation of the machine, system utilities and back-up procedures. Copies of these sections are kept in a 'Nyrex' folder with the computer. (2) Sections referring to the software written particularly for Positron Camera Data Collection describe the system in outline and lead to details of file formats and program source files. (3) The remainder of the guide, describes General-Purpose Software. Much of this has been written over some years by various members of the Data Handling Group, and is available for use in other applications besides the positron camera. (UK)

Use of an excess variance approach for the certification of reference materials by interlaboratory comparison

International Nuclear Information System (INIS)

Crozet, M.; Rigaux, C.; Roudil, D.; Tuffery, B.; Ruas, A.; Desenfant, M.

2014-01-01

In the nuclear field, the accuracy and comparability of analytical results are crucial to insure correct accountancy, good process control and safe operational conditions. All of these require reliable measurements based on reference materials whose certified values must be obtained by robust metrological approaches according to the requirements of ISO guides 34 and 35. The data processing of the characterization step is one of the key steps of a reference material production process. Among several methods, the use of interlaboratory comparison results for reference material certification is very common. The DerSimonian and Laird excess variance approach, described and implemented in this paper, is a simple and efficient method for the data processing of interlaboratory comparison results for reference material certification. By taking into account not only the laboratory uncertainties but also the spread of the individual results into the calculation of the weighted mean, this approach minimizes the risk to get biased certified values in the case where one or several laboratories either underestimate their measurement uncertainties or do not identify all measurement biases. This statistical method has been applied to a new CETAMA plutonium reference material certified by interlaboratory comparison and has been compared to the classical weighted mean approach described in ISO Guide 35. This paper shows the benefits of using an 'excess variance' approach for the certification of reference material by interlaboratory comparison. (authors)

Perl/Tk Pocket Reference

CERN Document Server

Lidie, Stephen

1998-01-01

The Perl/Tk Pocket Reference is a companion volume to Learning Perl/Tk, an O'Reilly Animal Guide. Learning Perl/Tk is a tutorial for Perl/Tk, the extension to Perl for creating graphical user interfaces. With Tk, Perl programs can be window-based rather than command-line based, with buttons, entry fields, listboxes, menus, scrollbars, balloons, tables, dialogs, and more. And Perl/Tk programs run on UNIX and Windows-based computers. This small book is a handy reference guide geared toward the advanced Perl/Tk programmer. Novice Perl/Tk programmers will find that its compact size gives th

Usefulness of herbal and dietary supplement references.

Science.gov (United States)

Sweet, Burgunda V; Gay, Wendy E; Leady, Michelle A; Stumpf, Janice L

2003-04-01

To describe the usefulness of some of the most common tertiary references that healthcare professionals employ to answer requests about herbal and dietary supplements. All requests for information on herbal and dietary supplements received by the drug information service between April and September 2000 were evaluated. Each question was independently reviewed by 4 clinicians using a 4-point scale; 14 references were searched for appropriate answers. The percent of responses for each of the possible scores for each reference overall and by category of question was reported to determine the most helpful references for answering the broadest range of questions. Fifty questions regarding herbal and dietary supplements were analyzed. The electronic databases (Natural Medicine Comprehensive Database, Micromedex) and the Internet site (The Natural Pharmacist) were determined to be overall the most helpful references for providing information on herbal and dietary supplements. The Natural Therapeutics Pocket Guide was the most helpful book reference. These results will facilitate the retrieval of useful information on herbal and dietary supplements and enable healthcare professionals to determine appropriate allocation of resources as they build a drug information library for handling requests about these products.

The SocioEconomic analysis of repository siting (SEARS): Guide to data base preparation: Final draft

International Nuclear Information System (INIS)

Hamm, R.R.; Murdock, S.H.; Leistritz, F.L.; Kiel, B.; Parpia, B.

1984-11-01

This guide describes the data bases in the SocioEconomic Analysis of Repository Siting (SEARS) modeling system. This model is a user-interactive, computerized model for projecting the economic, demographic, public service, and fiscal impacts of repository siting. This guide provides a description of the data bases, sources of data, data formats, and preprocessing programs for adapting and implementing the SEARS system and is seen as an essential reference for technical users of the model. It should be used in conjunction with reports describing the model's features and characteristics. 95 refs., 3 tabs

Fundamentals of Managing Reference Collections

Science.gov (United States)

Singer, Carol A.

2012-01-01

Whether a library's reference collection is large or small, it needs constant attention. Singer's book offers information and insight on best practices for reference collection management, no matter the size, and shows why managing without a plan is a recipe for clutter and confusion. In this very practical guide, reference librarians will learn:…

CT guided diagnostic foot injections

International Nuclear Information System (INIS)

Saifuddin, A.; Abdus-Samee, M.; Mann, C.; Singh, D.; Angel, J.C.

2005-01-01

AIM: To describe a CT technique for guiding diagnostic and therapeutic injections in the hind- and mid-foot. MATERIALS AND METHODS: Over a period of 50 months, 28 individuals were referred for diagnostic and therapeutic hind- and mid-foot injections before possible arthrodesis. A CT technique was developed that allowed entry into the various joints using a vertical approach. Numbers of joints injected were as follows: posterior subtalar, 21; talonavicular, 4; calcaneonavicular, calcaneocuboid, navicular-cuneiform and 5th metatarsocuboid joints, 1 each. RESULTS: All injections but one were technically successful. Significant relief of symptoms was noted by 16 participants, whereas for 9 there was no improvement and for 3 a partial response was achieved. CONCLUSION: CT is a simple and safe alternative to fluoroscopy for guiding diagnostic and therapeutic foot injections, and may be the technique of choice in cases of disordered anatomy

Preparation and characterization of the fish reference material

International Nuclear Information System (INIS)

Ulrich, Joao Cristiano

2011-01-01

The certified reference materials (CRMs) play an important role in obtaining measurement results traceable to the International System of Units, through an unbroken chain of comparisons. Thus, the demand for new certified reference materials (CRMs) increases every day in all areas of knowledge. The availability of reference materials, mainly in Brazil is still incipient, given that the demand far exceeds the available variety of these materials. The amount of certified reference materials available in the country is insufficient to meet the need of the scientific community and demands for development of new methodologies. Among the many areas in need of reference materials, we highlight the importance for the food trade balance for these products within the country. The certification of food products, intended both for export and for domestic consumption, requires analysis methods that provide precise and accurate results to ensure product quality. This paper describes the preparation and certification of a reference material in the fish matrix in mercury and methylmercury. The study brings together since the stage of material selection, preparation, development of homogeneity and stability studies and characterization. The certification was performed by means of measurements using two analytical techniques, flow injection analysis - cold vapor atomic absorption spectrometry (FIA-CV-AAS) and isotope dilution applied to mass spectrometry (IDMS), which is a primary method. In this work the standards of the ISO 30 (ABNT 30-34) and ISO Guide 35 was used as the basis for the preparation and characterization of the material. For the calculation of uncertainties was used the GUM and Eurachem guide. As a result, was produced and certified a lot of material in relation to the concentration of mercury (Hg = 0.271 ± 0.057 mg g -1 ) and methylmercury (MeHg = 0.245 ± 0.038 mg g -1 ), and informational values of lead and arsenic. (author)

No Experience Necessary: A Guide to Employment for the Female Liberal Arts Graduate.

Science.gov (United States)

Friedman, Sande; Schwartz, Lois C.

A guide for beginning employment for female liberal arts graduates (referred to as FLAGs), this book describes 14 fields found to be presently most accessible to FLAGs without advanced degrees: advertising, the art world, banking and finance, book publishing, computer programing, fashion (and beauty), films, Government, magazine and newspaper…

CSS Pocket Reference

CERN Document Server

Meyer, Eric

2011-01-01

When you're working with CSS and need a quick answer, CSS Pocket Reference delivers. This handy, concise book provides all of the essential information you need to implement CSS on the fly. Ideal for intermediate to advanced web designers and developers, the 4th edition is revised and updated for CSS3, the latest version of the Cascading Style Sheet specification. Along with a complete alphabetical reference to CSS3 selectors and properties, you'll also find a short introduction to the key concepts of CSS. Based on Cascading Style Sheets: The Definitive Guide, this reference is an easy-to-us

TclTk Pocket Reference

CERN Document Server

Raines, Paul

1998-01-01

The Tcl/Tk combination is increasingly popular because it lets you produce sophisticated graphical interfaces with a few easy commands, develop and change scripts quickly, and conveniently tie together existing utilities or programming libraries. The Tcl/Tk Pocket Reference,a handy reference guide to the basic Tcl language elements, Tcl and Tk commands, and Tk widgets, is a companion volume to Tcl/Tk in a Nutshell.

Environmental Guide Value (VGE) and specific reference values (QS) for uranium. Synthesis and elements for application to French fresh waters

International Nuclear Information System (INIS)

2015-01-01

This report proposes a synthesis of works performed to determine criteria of protection of continental aquatic ecosystems with respect to uranium. These works resulted in the determination of an environmental guide value (VGE) for the assessment of the ecological and chemical condition of waters. Other specific reference values have been determined to be used in risk assessment: average annual concentration, maximum admissible concentration. After a recall of the methodology adopted for the determination of VGE in the case of uranium, the report discusses the specific reference values in the case of uranium for different organisms, for predators, for the protection of human health against a risk of exposure by consumption of fished products or drinkable water. The determination of VGE and its application are reported, and its consistency with the criterion of radiation protection of the environment applied to water and sediments is discussed. The determination of specific reference values is then discussed

Electromagnetic ultrasonic guided waves

CERN Document Server

Huang, Songling; Li, Weibin; Wang, Qing

2016-01-01

This book introduces the fundamental theory of electromagnetic ultrasonic guided waves, together with its applications. It includes the dispersion characteristics and matching theory of guided waves; the mechanism of production and theoretical model of electromagnetic ultrasonic guided waves; the effect mechanism between guided waves and defects; the simulation method for the entire process of electromagnetic ultrasonic guided wave propagation; electromagnetic ultrasonic thickness measurement; pipeline axial guided wave defect detection; and electromagnetic ultrasonic guided wave detection of gas pipeline cracks. This theory and findings on applications draw on the author’s intensive research over the past eight years. The book can be used for nondestructive testing technology and as an engineering reference work. The specific implementation of the electromagnetic ultrasonic guided wave system presented here will also be of value for other nondestructive test developers.

Pocket Guide to Transportation 2018

Science.gov (United States)

2018-01-01

The 2018 BTS Pocket Guide to Transportation is a quick reference guide that provides transportation statistics at your fingertips. It provides key information and highlights major trends on the U.S. transportation system. This year features a new and...

A Reference Architecture for Space Information Management

Science.gov (United States)

Mattmann, Chris A.; Crichton, Daniel J.; Hughes, J. Steven; Ramirez, Paul M.; Berrios, Daniel C.

2006-01-01

We describe a reference architecture for space information management systems that elegantly overcomes the rigid design of common information systems in many domains. The reference architecture consists of a set of flexible, reusable, independent models and software components that function in unison, but remain separately managed entities. The main guiding principle of the reference architecture is to separate the various models of information (e.g., data, metadata, etc.) from implemented system code, allowing each to evolve independently. System modularity, systems interoperability, and dynamic evolution of information system components are the primary benefits of the design of the architecture. The architecture requires the use of information models that are substantially more advanced than those used by the vast majority of information systems. These models are more expressive and can be more easily modularized, distributed and maintained than simpler models e.g., configuration files and data dictionaries. Our current work focuses on formalizing the architecture within a CCSDS Green Book and evaluating the architecture within the context of the C3I initiative.

Artificial guide stars for adaptive optics using unmanned aerial vehicles

Science.gov (United States)

Basden, A. G.; Brown, Anthony M.; Chadwick, P. M.; Clark, P.; Massey, R.

2018-06-01

Astronomical adaptive optics (AO) systems are used to increase effective telescope resolution. However, they cannot be used to observe the whole sky since one or more natural guide stars of sufficient brightness must be found within the telescope field of view for the AO system to work. Even when laser guide stars are used, natural guide stars are still required to provide a constant position reference. Here, we introduce a technique to overcome this problem by using rotary unmanned aerial vehicles (UAVs) as a platform from which to produce artificial guide stars. We describe the concept that relies on the UAV being able to measure its precise relative position. We investigate the AO performance improvements that can be achieved, which in the cases presented here can improve the Strehl ratio by a factor of at least 2 for a 8 m class telescope. We also discuss improvements to this technique, which is relevant to both astronomical and solar AO systems.

Nuclear structure references coding manual

International Nuclear Information System (INIS)

Ramavataram, S.; Dunford, C.L.

1984-02-01

This manual is intended as a guide to Nuclear Structure References (NSR) compilers. The basic conventions followed at the National Nuclear Data Center (NNDC), which are compatible with the maintenance and updating of and retrieval from the Nuclear Structure References (NSR) file, are outlined. The structure of the NSR file such as the valid record identifiers, record contents, text fields as well as the major topics for which [KEYWORDS] are prepared are ennumerated. Relevant comments regarding a new entry into the NSR file, assignment of [KEYNO ], generation of [SELECTRS] and linkage characteristics are also given. A brief definition of the Keyword abstract is given followed by specific examples; for each TOPIC, the criteria for inclusion of an article as an entry into the NSR file as well as coding procedures are described. Authors submitting articles to Journals which require Keyword abstracts should follow the illustrations. The scope of the literature covered at NNDC, the categorization into Primary and Secondary sources, etc. is discussed. Useful information regarding permitted character sets, recommended abbreviations, etc. is given

LINQ Pocket Reference

CERN Document Server

Albahari, Joseph

2008-01-01

Ready to take advantage of LINQ with C# 3.0? This guide has the detail you need to grasp Microsoft's new querying technology, and concise explanations to help you learn it quickly. And once you begin to apply LINQ, the book serves as an on-the-job reference when you need immediate reminders. All the examples in the LINQ Pocket Reference are preloaded into LINQPad, the highly praised utility that lets you work with LINQ interactively. Created by the authors and free to download, LINQPad will not only help you learn LINQ, it will have you thinking in LINQ. This reference explains: LINQ's ke

Development, Use and Maintenance of the Design Basis Threat. Implementing Guide (French Edition); Elaboration, utilisation et actualisation de la menace de reference. Guide d'application

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-08-15

This publication provides guidance on how to develop, use and maintain a design basis threat (DBT). It is intended for decision makers from organizations with roles and responsibilities for the development, use and maintenance of the DBT. This implementing guide describes a DBT; identifies and recommends the roles and responsibilities of organizations that should be involved in the development, use and maintenance of a DBT; describes how to conduct a national threat assessment as a precursor to a DBT; explains how a DBT can be developed; explains how a DBT is incorporated into a State's nuclear security regime; and explains the conditions for a review of the DBT, and how the review and update are conducted.

Scheduling language and algorithm development study. Volume 2, phase 2: Introduction to plans programming. [user guide

Science.gov (United States)

Cochran, D. R.; Ishikawa, M. K.; Paulson, R. E.; Ramsey, H. R.

1975-01-01

A user guide for the Programming Language for Allocation and Network Scheduling (PLANS) is presented. Information is included for the construction of PLANS programs. The basic philosophy of PLANS is discussed, and access and update reference techniques are described along with the use of tree structures.

Oracle PL/SQL Language Pocket Reference

CERN Document Server

Feuerstein, Steven; Dawes, Chip

2007-01-01

The fourth edition of this popular pocket guide provides quick-reference information that will help you use Oracle's PL/SQL language, including the newest Oracle Database 11g features. A companion to Steven Feuerstein and Bill Pribyl's bestselling Oracle PL/SQL Programming, this concise guide boils down the most vital PL/SQL information into an accessible summary

A reference guide to quality assurance for diagnostic radiography

International Nuclear Information System (INIS)

1986-01-01

The College of Radiographers, through its Professional and Technical Committee, set up a small Working Party to compile a list of references which would help radiographers to become experts at Quality Assurance in Diagnostic Imaging departments. The list is not comprehensive, but includes references which the Working Party have experience of and have found useful. The references provided should aid in the objectives of:- 1. determining acceptable standards of new equipment; 2. making comparisons during use with accepted base line performance; 3. establishing loss of cost effectiveness and the need for replacement. (author)

Is an eclipse described in the Odyssey?

Science.gov (United States)

Baikouzis, Constantino; Magnasco, Marcelo O

2008-07-01

Plutarch and Heraclitus believed a certain passage in the 20th book of the Odyssey ("Theoclymenus's prophecy") to be a poetic description of a total solar eclipse. In the late 1920s, Schoch and Neugebauer computed that the solar eclipse of 16 April 1178 B.C.E. was total over the Ionian Islands and was the only suitable eclipse in more than a century to agree with classical estimates of the decade-earlier sack of Troy around 1192-1184 B.C.E. However, much skepticism remains about whether the verses refer to this, or any, eclipse. To contribute to the issue independently of the disputed eclipse reference, we analyze other astronomical references in the Epic, without assuming the existence of an eclipse, and search for dates matching the astronomical phenomena we believe they describe. We use three overt astronomical references in the epic: to Boötes and the Pleiades, Venus, and the New Moon; we supplement them with a conjectural identification of Hermes's trip to Ogygia as relating to the motion of planet Mercury. Performing an exhaustive search of all possible dates in the span 1250-1115 B.C., we looked to match these phenomena in the order and manner that the text describes. In that period, a single date closely matches our references: 16 April 1178 B.C.E. We speculate that these references, plus the disputed eclipse reference, may refer to that specific eclipse.

NORM - practical guide; NORM - guia pratico

Energy Technology Data Exchange (ETDEWEB)

Reis, Rocio dos (ed.)

2016-07-01

The experience of the authors and a literature review on the evaluation of national and international regulatory guides are presented. The objective is to help understand the need to implement the best practices for NORM management in the industries that produce the NORM wastes. The book should act as a reference point, basic, friendly and useful to assist the reader in NORM management activities. The reader should be warned that management requires consultation and involvement of a significant number of stakeholders, in addition to the approval of competent authorities. A list and the technical biography of the authors are also described.

Library Guides to Business Information.

Science.gov (United States)

Harris, Jamie L., Comp.

This collection of library guides is designed to introduce undergraduate students at Chicago State University to basic business reference sources. Annotated bibliographies cover the subject areas of business management, marketing, and finance. Guides in the collection include: (1) Researching the Company (Chicago and Illinois business and national…

Student Use of Library Research Guides Following Library Instruction

Directory of Open Access Journals (Sweden)

Mardi Mahaffy

2013-02-01

Full Text Available Librarians often provide students who attend one-shot library instruction sessions with research guides they can refer to once class is over. These guides, whether in paper or electronic form, serve to remind the students of key points and resources addressed during the session. It is unclear, though, if and how students refer to these guides once leaving the classroom. This article reports on the results of two focus groups made up of students who attended a basic library instruction session as part of a survey art course. The students shared how they used a paper and electronic research guide, delivered via LibGuides, and what they would like research guides to contain. The article also suggests directions for further research on the topic.

Nuclear fuel assembly grid sleeve/guide thimble bulge orientation gage and inspection method

International Nuclear Information System (INIS)

Widener, W.H.

1988-01-01

This patent describes a method of inspecting a fuel assembly to determine the orientation of externally-projecting mated bulges connecting a grid sleeve to a guide thimble of the assembly, the method comprising the steps of: (a) inserting a radially-expandable tubular member within the guide thimble, the tubular member having externally-projecting embossments thereon spaced circumferentially from one another about the tubular member, the embossments being the same in number as the bulges of the guide thimble and configured to fit therewithin; (b) axially moving an elongated expansion member, which extends through and rotatably mounts the tubular member, relative to the tubular member from a first position in which the expansion member permits inward contraction of the tubular member and displacement of embossments thereon away from the interior of the guide thimble bulges for removing the embossments from registry therewith and a second position in which the expansion member produces radial expansion of the tubular member and displacement of the embossments thereon toward the interior of the guide thimble bulges for placing the embossments in registry therewith; (c) rotating the tubular member relative to the expansion member so as to bring the embossments on the tubular member into alignment with the guide thimble bulges as the embossments on the tubular member are being displaced toward and into registry with the interior of the bulges; and (d) responsive to rotation of the tubular member away from a reference position, providing an indication of the orientation of the guide thimble bulges relative to a reference point upon displacement of the embossments into registry therewith

Technology guide. Principles - applications - trends

Energy Technology Data Exchange (ETDEWEB)

Bullinger, Hans-Joerg (ed.) [Fraunhofer-Gesellschaft, Muenchen (Germany)

2009-07-01

Use this TECHNOLOGY GUIDE to - find descriptions of today's most essential global technologies, clearly structured and simply explained in over 100 expert contributions; - gain an understanding of the principles behind each technology, - the latest applications, the challenges ahead, and future trends; - see how and where technologies and topics are interlinked, with cross-references and further sources of information; - broaden your general knowledge of technology, presented in a comprehensive reference format that invites even the casual reader to explore the stimulating innovative ideas it contains. This guide is a useful companion for readers with a lively interest in technology. It serves as a reference work for corporate and public-sector decision makers, as well as those involved in media and government. (orig.)

Assessment of pressurized nuclear equipment compliance - ASN guide no. 8, version of 04/09/2012

International Nuclear Information System (INIS)

2012-01-01

This document describes the modalities according to which the compliance assessment of pressurized nuclear equipment must be performed by inspecting organisations according to a decree of December 1999 and an order of December 2005. After an indication of reference documents and some technical definitions, this guide describes the equipment classification and the principles of intervention. These principles concern the assessment request and the various assessment tasks to be performed by the inspecting organisation

Lawrence Livermore National Laboratory Working Reference Material Production Pla

Energy Technology Data Exchange (ETDEWEB)

Wong, Amy; Thronas, Denise; Marshall, Robert

1998-11-04

This Lawrence Livermore National Laboratory (LLNL) Working Reference Material Production Plan was written for LLNL by the Los Alamos National Laboratory to address key elements of producing seven Pu-diatomaceous earth NDA Working Reference Materials (WRMS). These WRMS contain low burnup Pu ranging in mass from 0.1 grams to 68 grams. The composite Pu mass of the seven WRMS was designed to approximate the maximum TRU allowable loading of 200 grams Pu. This document serves two purposes: first, it defines all the operations required to meet the LLNL Statement of Work quality objectives, and second, it provides a record of the production and certification of the WRMS. Guidance provided in ASTM Standard Guide C1128-89 was used to ensure that this Plan addressed all the required elements for producing and certifying Working Reference Materials. The Production Plan was written to provide a general description of the processes, steps, files, quality control, and certification measures that were taken to produce the WRMS. The Plan identifies the files where detailed procedures, data, quality control, and certification documentation and forms are retained. The Production Plan is organized into three parts: a) an initial section describing the preparation and characterization of the Pu02 and diatomaceous earth materials, b) middle sections describing the loading, encapsulation, and measurement on the encapsulated WRMS, and c) final sections describing the calculations of the Pu, Am, and alpha activity for the WRMS and the uncertainties associated with these quantities.

Comparing the Effects of Progressive Muscle Relaxation and Guided Imagery on sleep quality in primigravida women referring to Mashhad health care centers-1393

OpenAIRE

Nahid Golmakani; Farnaz Sadat Seyed Ahmadi Nejad; Mohammad Taghi Shakeri; Negar Asghari Pour

2015-01-01

Background & aim: Decreased sleep quality is a common complaint during pregnancy. Relaxation is one of the non-pharmaceutical treatments for sleep disorders. Different techniques could have different impacts on various biological and mental stressors. Therefore, this study aimed to compare the effects of progressive muscle relaxation and guided imagery on the sleep quality of primigravida women. Methods:This three-group clinical trial was conducted on 100 primigravida women, referring to Mash...

Science reference room index to physical, chemical and other property data

CERN Document Server

This nice reference guide from Arizona State University's Noble Science and Engineering Library amounts to "an index to selected library and internet resources that contain chemical, physical, thermodynamic, mechanical, toxicological, and safety data with a list of suggested standard reference sources that may be found in most technical libraries, this reference guide goes on to include a vast reservoir of alphabetically listed library books and Internet sites where a user may locate specific information. From Abrasion Resistance to Yield Strength data, this index is quite comprehensive.

Field Guides Made Easy. 4-H Leader's Guide L-5-21.

Science.gov (United States)

Phillips, Diane Held; Krasny, Marianne E.

This illustrated leader's guide describes activities for teaching children to use field guides to identify trees and birds. Background information for leaders explains the two types of field guides, those that use a series of steps in what is called a key to identify things in nature, such as trees, and those that use groupings based on…

Growth references

NARCIS (Netherlands)

Buuren, S. van

2007-01-01

A growth reference describes the variation of an anthropometric measurement within a group of individuals. A reference is a tool for grouping and analyzing data and provides a common basis for comparing populations.1 A well known type of reference is the age-conditional growth diagram. The

HTML & XHTML Pocket Reference

CERN Document Server

Robbins, Jennifer

2010-01-01

After years of using spacer GIFs, layers of nested tables, and other improvised solutions for building your web sites, getting used to the more stringent standards-compliant design can be intimidating. HTML and XHTML Pocket Reference is the perfect little book when you need answers immediately. Jennifer Niederst-Robbins, author Web Design in a Nutshell, has revised and updated the fourth edition of this pocket guide by taking the top 20% of vital reference information from her Nutshell book, augmenting it judiciously, cross-referencing everything, and organizing it according to the most com

Python pocket reference

CERN Document Server

Lutz, Mark

2010-01-01

This is the book to reach for when you're coding on the fly and need an answer now. It's an easy-to-use reference to the core language, with descriptions of commonly used modules and toolkits, and a guide to recent changes, new features, and upgraded built-ins -- all updated to cover Python 3.X as well as version 2.6. You'll also quickly find exactly what you need with the handy index. Written by Mark Lutz -- widely recognized as the world's leading Python trainer -- Python Pocket Reference, Fourth Edition, is the perfect companion to O'Reilly's classic Python tutorials, also written by Mark

VMware vSphere 5 Administration Instant Reference

CERN Document Server

Kusek, Christopher; Daniel, Andy

2011-01-01

Compact and portable reference guide for quick answers to VMware vSphere If you're looking to migrate to the newest version of VMware vSphere, this concise guide will get you up to speed and down to business in no time. If you're new to VMware vSphere, this book is for you too! The compact size of this quick reference makes it easy for you to have by your side—whether you're in the field, server room, or at your desk. Helpful elements for finding information such as thumb tabs, tables of contents with page numbers at the beginning of each chapter, and special headers puts what you need a

Dengue and Chikungunya Vector Control Pocket Guide

Science.gov (United States)

This technical guide consolidates information and procedures for surveillance and control of mosquitoes that transmit dengue and chikungunya viruses. The guide focuses on mosquitoes that transmit dengue but also makes reference to chikungunya and yellow fever because the pathogens that cause these ...

Evidence: Study Guide. Revision

National Research Council Canada - National Science Library

1997-01-01

...) correct application of principles of military rules of evidence. This study guide is also intended to be a convenient reference for use by Navy and Marine Corps judge advocates and Coast Guard law...

Visual Basic 2012 programmer's reference

CERN Document Server

Stephens, Rod

2012-01-01

The comprehensive guide to Visual Basic 2012 Microsoft Visual Basic (VB) is the most popular programming language in the world, with millions of lines of code used in businesses and applications of all types and sizes. In this edition of the bestselling Wrox guide, Visual Basic expert Rod Stephens offers novice and experienced developers a comprehensive tutorial and reference to Visual Basic 2012. This latest edition introduces major changes to the Visual Studio development platform, including support for developing mobile applications that can take advantage of the Windows 8 operating system

Standard guide for computed radiography

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This guide provides general tutorial information regarding the fundamental and physical principles of computed radiography (CR), definitions and terminology required to understand the basic CR process. An introduction to some of the limitations that are typically encountered during the establishment of techniques and basic image processing methods are also provided. This guide does not provide specific techniques or acceptance criteria for specific end-user inspection applications. Information presented within this guide may be useful in conjunction with those standards of 1.2. 1.2 CR techniques for general inspection applications may be found in Practice E2033. Technical qualification attributes for CR systems may be found in Practice E2445. Criteria for classification of CR system technical performance levels may be found in Practice E2446. Reference Images Standards E2422, E2660, and E2669 contain digital reference acceptance illustrations. 1.3 The values stated in SI units are to be regarded as the st...

National Environmental Policy Act compliance guide. Volume II (reference book)

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-09-01

This document (Volume II of the National Environmental Policy Act Compliance Guide) contains current copies of regulations and guidance from the Council on Environmental Quality, the Department of Energy, the Department of State, and the Environmental Protection Agency, related to compliance with the National Environmental Policy Act of 1969 (NEPA).

FIRINPC and FIRACPC graphics post-processor support user's guide and programmer's reference

International Nuclear Information System (INIS)

Hensel, E.

1992-03-01

FIRIN is a computer program used by DOE fire protection engineers to simulate hypothetical fire accidents in compartments at DOE facilities. The FIRIN code is typically used in conjunction with a ventilation system code such as FIRAC, which models the impact of the fire compartment upon the rest of the system. The code described here, FIRINPC is a PC based implementation of the full mainframe code FIRIN. In addition, FIRINPC contains graphics support for monitoring the progress of the simulation during execution and for reviewing the complete results of the simulation upon completion of the run. This document describes how to install, test, and subsequently use the code FIRINPC, and addresses differences in usage between the PC version of the code and its mainframe predecessor. The PC version contains all of the modeling capabilities of the earlier version, with additional graphics support. This user's guide is a supplement to the original FIRIN report published by the NRC. FIRAC is a computer program used by DOE fire protection engineers to simulate the transient response of complete ventilation system to fire induced transients. FIRAC has the ability to use the FIRIN code as the driving function or source term for the ventilation system response. The current version of FIRAC does not contain interactive graphics capabilities. A third program, called POST, is made available for reviewing the results of a previous FIRIN or FIRAC simulation, without having to recompute the numerical simulation. POST uses the output data files created by FIRINPC and FIRACPC to avoid recomputation

A beginner's guide to the use of WIMS

International Nuclear Information System (INIS)

Halsall, M.J.

1987-04-01

The WIMS codes are widely used for calculating the characteristics of thermal reactor lattices. WIMSD has changed little since the 1960s and is most useful for pincell and cluster calculations, WIMS-E is a modular scheme with more flexibility, and LWRWIMS is specifically for PWR and BWR assembly representations. This report provides a brief introductory guide for inexperienced users of the WIMS codes. There is an introductory part to explain why and when to use WIMS, with particular reference to the advantages of deterministic methods over stochastic (Monte Carlo) methods. A few comments on which version to use are then followed by a summary of commonly used options with examples. References are given to more complete documentation describing the input in greater detail; users are expected to move on to this as they gain experience. (author)

Guide to good practices for the development of test items

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

While the methodology used in developing test items can vary significantly, to ensure quality examinations, test items should be developed systematically. Test design and development is discussed in the DOE Guide to Good Practices for Design, Development, and Implementation of Examinations. This guide is intended to be a supplement by providing more detailed guidance on the development of specific test items. This guide addresses the development of written examination test items primarily. However, many of the concepts also apply to oral examinations, both in the classroom and on the job. This guide is intended to be used as guidance for the classroom and laboratory instructor or curriculum developer responsible for the construction of individual test items. This document focuses on written test items, but includes information relative to open-reference (open book) examination test items, as well. These test items have been categorized as short-answer, multiple-choice, or essay. Each test item format is described, examples are provided, and a procedure for development is included. The appendices provide examples for writing test items, a test item development form, and examples of various test item formats.

Comparing the Effects of Progressive Muscle Relaxation and Guided Imagery on sleep quality in primigravida women referring to Mashhad health care centers-1393

Directory of Open Access Journals (Sweden)

Nahid Golmakani

2015-04-01

Full Text Available Background & aim: Decreased sleep quality is a common complaint during pregnancy. Relaxation is one of the non-pharmaceutical treatments for sleep disorders. Different techniques could have different impacts on various biological and mental stressors. Therefore, this study aimed to compare the effects of progressive muscle relaxation and guided imagery on the sleep quality of primigravida women. Methods:This three-group clinical trial was conducted on 100 primigravida women, referring to Mashhad health care centers in 2014. All women, who met the inclusion criteria, were randomly assigned to three groups: progressive muscle relaxation, guided imagery, and control groups. The intervention groups performed the exercises twice a day for a period of four weeks at home after two sessions of relaxation training (held during two weeks. Then, the quality of sleep was measured using Pittsburgh Sleep Quality Index. For data analysis, ANOVA, Kruskal-Wallis, paired t-test, and post-hoc test were performed, using SPSS version 11.5. Results: The total score of sleep quality and its components (except use of sleep medication was significantly lower after the intervention, compared to the pre-intervention period in progressive muscle relaxation and guided imagery groups (P

Using LibGuides to enhance library services a LITA guide

CERN Document Server

Dobbs, Aaron W

2013-01-01

The easy-to-use tools in Springshare's LibGuides help you organize webpages, improve students' research experience and learning, and offer an online community of librarians sharing their work and ideas. Editors Dobbs, Sittler, and Cook have recruited expert contributors to address specific applications, creating a one-stop reference.

Nuclear science references coding manual

International Nuclear Information System (INIS)

Ramavataram, S.; Dunford, C.L.

1996-08-01

This manual is intended as a guide to Nuclear Science References (NSR) compilers. The basic conventions followed at the National Nuclear Data Center (NNDC), which are compatible with the maintenance and updating of and retrieval from the Nuclear Science References (NSR) file, are outlined. In Section H, the structure of the NSR file such as the valid record identifiers, record contents, text fields as well as the major TOPICS for which are prepared are enumerated. Relevant comments regarding a new entry into the NSR file, assignment of , generation of and linkage characteristics are also given in Section II. In Section III, a brief definition of the Keyword abstract is given followed by specific examples; for each TOPIC, the criteria for inclusion of an article as an entry into the NSR file as well as coding procedures are described. Authors preparing Keyword abstracts either to be published in a Journal (e.g., Nucl. Phys. A) or to be sent directly to NNDC (e.g., Phys. Rev. C) should follow the illustrations in Section III. The scope of the literature covered at the NNDC, the categorization into Primary and Secondary sources, etc., is discussed in Section IV. Useful information regarding permitted character sets, recommended abbreviations, etc., is given under Section V as Appendices

Shakespeare: A Student's Guide to Basic Reference Sources.

Science.gov (United States)

Claener, Anne, Comp.

Basic and standard reference materials dealing with William Shakespeare are listed in this bibliography. Annotated entries are grouped under the following headings: concordances, dictionaries, encyclopedias and handbooks, and bibliographies. The section on bibliographies is further divided into lists of editions of Shakespeare's work, general…

Reference Etiquette: A Guide to Excruciatingly Correct Behavior.

Science.gov (United States)

Eckwright, Gail Z.; Pollastro, Mike; Hoskisson, Tam

1998-01-01

Presents suggestions for smooth and satisfying transactions between reference librarians and patrons, as well as for better collegial relationships. Highlights include: being prepared to help patrons; staying visible; serving "who's next"; working together and allowing for personal styles; making referrals; and using diplomacy while correcting…

How role distribution influences choice of spatial reference frames in a virtual collaborative task

OpenAIRE

Pouliquen-Lardy , Lauriane; Milleville-Pennel , Isabelle; Guillaume , François; Mars , Franck

2014-01-01

International audience; We investigated the effects of role distribution on individuals' choice of reference frames in a two-person task. Pairs of participants had to move a virtual block in a constraint immersive virtual environment: only one of them could manipulate the ob-ject, his coworker guided him in the VE. Results show that the guiding operators used more addressee-centered frames of ref-erence than the manipulators. They also suggest that the guides tried to facilitate the manipulat...

NASCAP programmer's reference manual

Science.gov (United States)

Mandell, M. J.; Stannard, P. R.; Katz, I.

1993-05-01

The NASA Charging Analyzer Program (NASCAP) is a computer program designed to model the electrostatic charging of complicated three-dimensional objects, both in a test tank and at geosynchronous altitudes. This document is a programmer's reference manual and user's guide. It is designed as a reference to experienced users of the code, as well as an introduction to its use for beginners. All of the many capabilities of NASCAP are covered in detail, together with examples of their use. These include the definition of objects, plasma environments, potential calculations, particle emission and detection simulations, and charging analysis.

Guide to preparing SAND reports and other communication products.

Energy Technology Data Exchange (ETDEWEB)

2011-09-01

This guide describes the R&A process, Common Look and Feel requirements, and preparation and publishing procedures for communication products at Sandia National Laboratories. Samples of forms and examples of published communications products are provided. This guide takes advantage of the wealth of material now available on the Web as a resource. Therefore, it is best viewed as an electronic document. If some of the illustrations are too small to view comfortably, you can enlarge them on the screen as needed. The format of this document is considerably different than that usually expected of a SAND Report. It was selected to permit the large number of illustrations and examples to be placed closer to the text that references them. In the case of forms, covers, and other items that are included as examples, a link to the Web is provided so that you can access the items and download them for use. This guide details the processes for producing a variety of communication products at Sandia National Laboratories. Figure I-1 shows the general publication development process. Because extensive supplemental material is available from Sandia on the internal web or from external sources (Table I-1), the guide has been shortened to make it easy to find information that you need.

Writing a Thesis : A Guide for Scientific Reports

OpenAIRE

Engdahl, Ingrid; Sandqvist, Karin

2012-01-01

This guide is an introduction to one way to write scientific reports, the way we have been using and taught to our students in Teacher Education Programmes and Child and Youth Studies. It includes how to structure the text, suggested content to go under each heading, some rules about quotes and references, cooperation with the advisor and with fellow students and, finally, guides for the thesis seminar, an agenda for the seminar and advice for the opponent(s) and respondent(s). The references...

Determination of boron in ceramic reference materials by prompt gamma activation analysis using focused neutron guided beam of JRR-3M

International Nuclear Information System (INIS)

Miura, T.; Kuroiwa, T.; Chiba, K.; Matsue, H.

2008-01-01

Prompt gamma activation analysis using a focused thermal neutron guided beam at JAEA JRR-3M was applied to the determination of B in ceramic certified reference materials (BAM CRM S-003 Silicon Carbide Powder and NMIJ CRM 8004-a Silicon Nitride Powder). Cl and Si were used as internal standards to obtain linear calibration curves of B. The analytical result of B in BAM CRM S-003 was in good agreement with the certified value. The relative expanded measurement uncertainties (k = 2) were 4.8% for BAM CRM S-003 and 4.9% for NMIJ CRM 8004-a. (author)

The Johnson Space Center management information systems: User's guide to JSCMIS

Science.gov (United States)

Bishop, Peter C.; Erickson, Lloyd

1990-01-01

The Johnson Space Center Management Information System (JSCMIS) is an interface to computer data bases at the NASA Johnson Space Center which allows an authorized user to browse and retrieve information from a variety of sources with minimum effort. The User's Guide to JSCMIS is the supplement to the JSCMIS Research Report which details the objectives, the architecture, and implementation of the interface. It is a tutorial on how to use the interface and a reference for details about it. The guide is structured like an extended JSCMIS session, describing all of the interface features and how to use them. It also contains an appendix with each of the standard FORMATs currently included in the interface. Users may review them to decide which FORMAT most suits their needs.

Study guide for college algebra

CERN Document Server

Snow, James W; Shapiro, Arnold

1981-01-01

Study Guide for College Algebra is a supplemental material for the basic text, College Algebra. Its purpose is to make the learning of college algebra and trigonometry easier and enjoyable.The book provides detailed solutions to exercises found in the text. Students are encouraged to use the study guide as a learning tool during the duration of the course, a reviewer prior to an exam, a reference book, and as a quick overview before studying a section of the text. The Study Guide and Solutions Manual consists of four major components: basic concepts that should be learned from each unit, what

A Guide to the Field Guides.

Science.gov (United States)

Natural History, 1987

1987-01-01

Provides a compilation of recommended field guides which deal with birds, mammals, trees, and wildflowers. Each recommended volume is described, noting its distinguishing features and evaluating its organization, photography, and text. Includes the author, publisher, and suggested retail price. (TW)

Wiley guide to chemical incompatibilities

National Research Council Canada - National Science Library

Pohanish, Richard P; Greene, Stanley A

2009-01-01

.... A portable and easy-to-use reference on reactive substances commonly found in commerce, the Wiley Guide to Chemical Incompatibilities, Third Edition compiles hard-to-find data on over 11,000 chemical...

Manual on shielded enclosures. Incorporating: Applications guide, procedures guide, basics guide

International Nuclear Information System (INIS)

1992-01-01

This booklet contains a basic guide to the principles of the production of ionizing radiation and to methods of radiation protection and dosimetry, and a discussion of the need for shielded enclosures. Shielding materials and the design of the enclosures are described

JOKARUS - design of a compact optical iodine frequency reference for a sounding rocket mission

Energy Technology Data Exchange (ETDEWEB)

Schkolnik, Vladimir; Doeringshoff, Klaus; Gutsch, Franz Balthasar; Krutzik, Markus [Humboldt-Universitaet zu Berlin, Berlin (Germany); Oswald, Markus [Universitaet Bremen, Zentrum fuer angewandte Raumfahrttechnologie und Mikrogravitation (ZARM), Bremen (Germany); Schuldt, Thilo [Institut fuer Raumfahrtsysteme, Deutsches Zentrum fuer Luft- und Raumfahrt (DLR), Bremen (Germany); Braxmaier, Claus [Universitaet Bremen, Zentrum fuer angewandte Raumfahrttechnologie und Mikrogravitation (ZARM), Bremen (Germany); Institut fuer Raumfahrtsysteme, Deutsches Zentrum fuer Luft- und Raumfahrt (DLR), Bremen (Germany); Lezius, Matthias; Holzwarth, Ronald [Menlo Systems GmbH, Martinsried (Germany); Kuerbis, Christian; Bawamia, Ahmad [Leibniz-Institut fuer Hoechstfrequenztechnik, Ferdinand-Braun-Institut, Berlin (Germany); Peters, Achim [Humboldt-Universitaet zu Berlin, Berlin (Germany); Leibniz-Institut fuer Hoechstfrequenztechnik, Ferdinand-Braun-Institut, Berlin (Germany)

2017-12-15

We present the design of a compact absolute optical frequency reference for space applications based on hyperfine transitions in molecular iodine with a targeted fractional frequency instability of better than 3 x 10{sup -14} after 1 s. It is based on a micro-integrated extended cavity diode laser with integrated optical amplifier, fiber pigtailed second harmonic generation wave-guide modules, and a quasi-monolithic spectroscopy setup with operating electronics. The instrument described here is scheduled for launch end of 2017 aboard the TEXUS 54 sounding rocket as an important qualification step towards space application of iodine frequency references and related technologies. The payload will operate autonomously and its optical frequency will be compared to an optical frequency comb during its space flight. (orig.)

Guide to software export

CERN Document Server

Philips, Roger A

2014-01-01

An ideal reference source for CEOs, marketing and sales managers, sales consultants, and students of international marketing, Guide to Software Export provides a step-by-step approach to initiating or expanding international software sales. It teaches you how to examine critically your candidate product for exportability; how to find distributors, agents, and resellers abroad; how to identify the best distribution structure for export; and much, much more!Not content with providing just the guidelines for setting up, expanding, and managing your international sales channels, Guide to Software

Activity Management System user reference manual. Revision 1

International Nuclear Information System (INIS)

Gates, T.A.; Burdick, M.B.

1994-01-01

The Activity Management System (AMS) was developed in response to the need for a simple-to-use, low-cost, user interface system for collecting and logging Hanford Waste Vitrification Plant Project (HWVP) activities. This system needed to run on user workstations and provide common user access to a database stored on a local network file server. Most important, users wanted a system that provided a management tool that supported their individual process for completing activities. Existing system treated the performer as a tool of the system. All AMS data is maintained in encrypted format. Users can feel confident that any activities they have entered into the database are private and that, as the originator, they retain sole control over who can see them. Once entered into the AMS database, the activities cannot be accessed by anyone other than the originator, the designated agent, or by authorized viewers who have been explicitly granted the right to look at specific activities by the originator. This user guide is intended to assist new AMS users in learning how to use the application and, after the initial learning process, will serve as an ongoing reference for experienced users in performing infrequently used functions. Online help screens provide reference to some of the key information in this manual. Additional help screens, encompassing all the applicable material in this manual, will be incorporated into future AMS revisions. A third, and most important, source of help is the AMS administrator(s). This guide describes the initial production version of AMS, which has been designated Revision 1.0

Magnetic Field Measurements in Beam Guiding Magnets

CERN Document Server

Henrichsen, K N

1998-01-01

Electromagnets used as beam guiding elements in particle accelerators and colliders require very tight tole-rances on their magnetic fields and on their alignment along the particle path. This article describes the methods and equipment used for magnetic measurements in beam transport magnets. Descriptions are given of magnetic resonance techniques, various induction coil methods, Hall generator measurements, the fluxgate magnetometer as well as the recently developed method of beam based alignment. References of historical nature as well as citations of recent work are given. The present commercial availability of the different sensors and asso-ciated equipment is indicated. Finally we shall try to analyze possible future needs for developments in those fields.

An innovative service process development based on a reference model

Directory of Open Access Journals (Sweden)

Lorenzo Sanfelice Frazzon

2015-06-01

Full Text Available This article examines the new service development (NSD process, focusing specifically in a case of a financial service, guided by the following research questions: what are the processes and practices used in the development and design of new financial services? How the results of the financial NSD proposal reflects on the NSD are as a whole? Therefore, the study aims to show and describe a financial service development, conducted at Helpinveste. The paper focuses on the Conceptual Design service (activities: definition of specifications and development of alternative solutions for the service and Service Process Design (Service Representation phases. The methodological procedures are based on the process approach, using a reference model for developing new services. In order to operationalize the model, several techniques for the various stages of the project were used, e.g. QFD and Service Blueprint. Lastly, conclusions report contributions from the reference model application, both theoretical and practical contributions, as well the limitations and further research recommendations.

Selected Reference Books of 1971-72

Science.gov (United States)

Sheehy, Eugene P.

1973-01-01

The purpose of this annotated list is to present a selection of recent scholarly and foreign works of interest to reference workers in university libraries. The citations are listed under the following headings: guide, bibliography, encyclopedias, dictionaries, newspapers, dissertations, biography, genealogy, literature, education, sociology,…

Radiation exposure in CT-guided interventions

Energy Technology Data Exchange (ETDEWEB)

Kloeckner, Roman, E-mail: Roman.Kloeckner@unimedizin-mainz.de [Department of Diagnostic and Interventional Radiology, Johannes Gutenberg-University, Langenbeckstraße 1, 55131 Mainz (Germany); Santos, Daniel Pinto dos; Schneider, Jens [Department of Diagnostic and Interventional Radiology, Johannes Gutenberg-University, Langenbeckstraße 1, 55131 Mainz (Germany); Kara, Levent [Department of Radiology, Inselspital Bern, Freiburgstraße 18, 3010 Bern (Switzerland); Dueber, Christoph; Pitton, Michael B. [Department of Diagnostic and Interventional Radiology, Johannes Gutenberg-University, Langenbeckstraße 1, 55131 Mainz (Germany)

2013-12-01

Purpose: To investigate radiation exposure in computed tomography (CT)-guided interventions, to establish reference levels for exposure, and to discuss strategies for dose reduction. Materials and methods: We analyzed 1576 consecutive CT-guided procedures in 1284 patients performed over 4.5 years, including drainage placements; biopsies of different organs; radiofrequency and microwave ablations (RFA/MWA) of liver, bone, and lung tumors; pain blockages, and vertebroplasties. Data were analyzed with respect to scanner settings, overall radiation doses, and individual doses of planning CT series, CT intervention, and control CT series. Results: Eighy-five percent of the total radiation dose was applied during the pre- and post-interventional CT series, leaving only 15% applied by the CT-guided intervention itself. Single slice acquisition was associated with lower doses than continuous CT-fluoroscopy (37 mGy cm vs. 153 mGy cm, p < 0.001). The third quartile of radiation doses varied considerably for different interventions. The highest doses were observed in complex interventions like RFA/MWA of the liver, followed by vertebroplasty and RFA/MWA of the lung. Conclusions: This paper suggests preliminary reference levels for various intervention types and discusses strategies for dose reduction. A multicenter registry of radiation exposure including a broader spectrum of scanners and intervention types is needed to develop definitive reference levels.

Jenkins The Definitive Guide

CERN Document Server

Smart, John

2011-01-01

Streamline software development with Jenkins, the popular Java-based open source tool that has revolutionized the way teams think about Continuous Integration (CI). This complete guide shows you how to automate your build, integration, release, and deployment processes with Jenkins-and demonstrates how CI can save you time, money, and many headaches. Ideal for developers, software architects, and project managers, Jenkins: The Definitive Guide is both a CI tutorial and a comprehensive Jenkins reference. Through its wealth of best practices and real-world tips, you'll discover how easy it is

A guide to experimental particle physics literature, 1991-1996

International Nuclear Information System (INIS)

Ezhela, V.V.; Filimonov, B.B.; Lugovsky, S.B.

1996-10-01

We present an indexed guide to experimental particle physics literature for the years 1991 - 1996. Approximately 4200 papers are indexed by (1) Beam/Target/Momentum (2) Reaction/Momentum/Data-Descriptor (including the final state) (3) Particle/Decay (4) Accelerator/Experiment/Detector. All indices are cross-referenced to the paper''s title and references in the ID/Reference/Title index. The information presented in this guide is also publicly available on a regularly-updated DATAGUIDE database from the World Wide Web

A guide to experimental particle physics literature, 1991-1996

Energy Technology Data Exchange (ETDEWEB)

Ezhela, V.V.; Filimonov, B.B.; Lugovsky, S.B. [Inst. for High Energy Physics, Moscow (Russian Federation)] [and others

1996-10-01

We present an indexed guide to experimental particle physics literature for the years 1991 - 1996. Approximately 4200 papers are indexed by (1) Beam/Target/Momentum (2) Reaction/Momentum/Data-Descriptor (including the final state) (3) Particle/Decay (4) Accelerator/Experiment/Detector. All indices are cross-referenced to the paper`s title and references in the ID/Reference/Title index. The information presented in this guide is also publicly available on a regularly-updated DATAGUIDE database from the World Wide Web.

Image-guided drug delivery: preclinical applications and clinical translation

NARCIS (Netherlands)

Ojha, Tarun; Rizzo, Larissa; Storm, Gerrit; Kiessling, Fabian; Lammers, Twan Gerardus Gertudis Maria

2015-01-01

Image-guided drug delivery refers to the combination of drug targeting and imaging. Preclinically, image-guided drug delivery can be used for several different purposes, including for monitoring biodistribution, target site accumulation, off-target localization, drug release and drug efficacy.

Obesity and its association with diets and sedentary life style among school children in Seoul, Korea: Compliance with Dietary References Intakes for Koreans food guides.

Science.gov (United States)

Ha, Aewha

2007-01-01

This study compared obese children's food group intakes with the new Dietary References Intakes for Koreans (KDRIs) food guides for 5th-6th grade school children. This study also determined the extent of sedentary life styles related with obesity in this area of children. This is a cross-sectional study of 799 school children. The dietitian sent a survey form describing the project and a questionnaire to the subject's family. The questionnaire included child demographics, family history of chronic diseases, the daily servings of five food groups, such as grains, meat and beans, dairy products, fruits, and vegetables. The daily or weekly hours of physical activity, television viewing, and computer usage were also surveyed. Obesity index (%) of the subjects was calculated, and children with an obesity index (%) equal to or greater than 20 were classified as the obese. Among the 799 participants, 50.7% were female. The percentages of the normal and the obese were 691 (86.5%) and 108 (13.5%) respectively. Obese children reported eating less vegetables (psedentary lifestyle increased significantly the likelihood of obesity in children, which suggest that obesity intervention in this age group should focuse more on those variables.

Examining egocentric and allocentric frames of reference in virtual space systems

NARCIS (Netherlands)

Friedman, A.

2005-01-01

The aim of this paper is to examine the egocentric and allocentric frames of reference, through evidence from both gesture and linguistic communication. The action of frames of reference, helps the user refer to the agent as a base for movement or to the object as a guiding point. We will show that

Manual on nuclear gauges. Incorporating: Applications guide, procedures guide, basics guide

International Nuclear Information System (INIS)

1992-01-01

In addition to a basic guide to the principles of production of ionizing radiation and to the methods of radiation protection and dosimetry, this booklet considers the procedures that should be employed when using nuclear gauges. Applications for such gauges are described and radiation protection procedures discussed

Guide for International Peer Reviews of Decommissioning Cost Studies for Nuclear Facilities

International Nuclear Information System (INIS)

LaGuardia, Thomas S.; Pescatore, Claudio; )

2014-01-01

Peer reviews are a standard co-operative OECD working tool that offer member countries a framework to compare experiences and examine best practices in a host of areas. The OECD Nuclear Energy Agency (NEA) has developed a proven methodology for conducting peer reviews in radioactive waste management and nuclear R and D. Using this methodology, the NEA Radioactive Waste Management Committee's Working Party on Decommissioning and Dismantling (WPDD) developed the present guide as a framework for decommissioning cost reviewers and reviewees to prepare for and conduct international peer reviews of decommissioning cost estimate studies for nuclear facilities. It includes checklists that will help national programmes or relevant organisations to assess and improve decommissioning cost estimate practices in the future. This guide will act as the NEA reference for conducting such international peer reviews. The remainder of this guide is divided into eight chapters. Chapter 2 describes gathering the cost estimate study and underpinning documents, reviewing the study and writing a final report. Chapter 3 provides a detailed checklist approach for the review of the cost study report. Chapter 4 provides checklists to assist in reviewing benchmarked information. Chapter 5 provides comments on the approach and recommendations for use of this guide. Chapters 6 and 7 provide the background material used in developing this guide and Chapter 8 provides a list of the abbreviations and acronyms used in this guide

Standard guide for laboratory simulation of corrosion under insulation

CERN Document Server

American Society for Testing and Materials. Philadelphia

2007-01-01

1.1 This guide covers the simulation of corrosion under insulation (CUI), including both general and localized attack, on insulated specimens cut from pipe sections exposed to a corrosive environment usually at elevated temperature. It describes a CUI exposure apparatus (hereinafter referred to as a CUI-Cell), preparation of specimens, simulation procedures for isothermal or cyclic temperature, or both, and wet/dry conditions, which are parameters that need to be monitored during the simulation and the classification of simulation type. 1.2 The application of this guide is broad and can incorporate a range of materials, environments and conditions that are beyond the scope of a single test method. The apparatus and procedures contained herein are principally directed at establishing acceptable procedures for CUI simulation for the purposes of evaluating the corrosivity of CUI environments on carbon and low alloy pipe steels, and may possibly be applicable to other materials as well. However, the same or simi...

Mind over Matter. Teacher's Guide.

Science.gov (United States)

National Inst. on Drug Abuse (DHHS/PHS), Rockville, MD.

This teacher's guide aims to develop an understanding among students in grades 5-9 about the biological effects of drug use. The guide provides background information on the anatomy of the brain, nerve cells and neurotransmission, and the effects of drugs on the brain. Drugs described in this guide include marijuana, opiates, inhalants,…

Hospitality Services. Curriculum Guide [and] Student Activity Book [and] Reference Book.

Science.gov (United States)

Texas Tech Univ., Lubbock. Curriculum Center for Family and Consumer Sciences.

These three publications comprise a course that provides occupationally specific training designed to develop knowledge and skills for employment in the multifaceted hospitality services industry. The curriculum guide is the teacher component of the series. Contents include the Texas Essential Knowledge and Skills (TEKS); sample course outlines;…

Review of The Chicago Guide to Writing about Numbers by Jane E. Miller

Directory of Open Access Journals (Sweden)

Neil Lutsky

2009-01-01

Full Text Available Miller, J. E. 2004. The Chicago Guide to Writing about Numbers. Chicago, IL: University of Chicago Press. 304 pp. Cloth $45 ISBN: 9780226526300, Softcover $17. ISBN: 9780226526317.The Chicago Guide to Writing about Numbers is a reference work suitable for anyone interested in understanding, using, or promoting quantitative thinking. Its primary aim is to identify and illustrate ways in which information associated with numbers can be conveyed most effectively given a particular communication purpose and context. The book is directed at writers who incorporate numbers in verbal or visual displays in documents, in oral presentations, or on the Web. The Chicago Guide to Writing about Numbers identifies overarching principles, offers concrete advice, and presents illuminating examples and models. The book can be used for instructional purposes for undergraduates, and a means of doing so is described. The review concludes by considering the book’s contributions to a wider call to help citizens write or argue more effectively by using numbers.

Transportation and packaging resource guide

Energy Technology Data Exchange (ETDEWEB)

Arendt, J.W.; Gove, R.M.; Welch, M.J.

1994-12-01

The purpose of this resource guide is to provide a convenient reference document of information that may be useful to the U.S. Department of Energy (DOE) and DOE contractor personnel involved in packaging and transportation activities. An attempt has been made to present the terminology of DOE community usage as it currently exists. DOE`s mission is changing with emphasis on environmental cleanup. The terminology or nomenclature that has resulted from this expanded mission is included for the packaging and transportation user for reference purposes. Older terms still in use during the transition have been maintained. The Packaging and Transportation Resource Guide consists of four sections: Sect. 1, Introduction; Sect. 2, Abbreviations and Acronyms; Sect. 3, Definitions; and Sect. 4, References for packaging and transportation of hazardous materials and related activities, and Appendices A and B. Information has been collected from DOE Orders and DOE documents; U.S Department of Transportation (DOT), U.S. Environmental Protection Agency (EPA), and U.S. Nuclear Regulatory Commission (NRC) regulations; and International Atomic Energy Agency (IAEA) standards and other international documents. The definitions included in this guide may not always be a regulatory definition but are the more common DOE usage. In addition, the definitions vary among regulatory agencies. It is, therefore, suggested that if a definition is to be used in a regulatory or a legal compliance issue, the definition should be verified with the appropriate regulation. To assist in locating definitions in the regulations, a listing of all definition sections in the regulations are included in Appendix B. In many instances, the appropriate regulatory reference is indicated in the right-hand margin.

Transportation and packaging resource guide

International Nuclear Information System (INIS)

Arendt, J.W.; Gove, R.M.; Welch, M.J.

1994-12-01

The purpose of this resource guide is to provide a convenient reference document of information that may be useful to the U.S. Department of Energy (DOE) and DOE contractor personnel involved in packaging and transportation activities. An attempt has been made to present the terminology of DOE community usage as it currently exists. DOE's mission is changing with emphasis on environmental cleanup. The terminology or nomenclature that has resulted from this expanded mission is included for the packaging and transportation user for reference purposes. Older terms still in use during the transition have been maintained. The Packaging and Transportation Resource Guide consists of four sections: Sect. 1, Introduction; Sect. 2, Abbreviations and Acronyms; Sect. 3, Definitions; and Sect. 4, References for packaging and transportation of hazardous materials and related activities, and Appendices A and B. Information has been collected from DOE Orders and DOE documents; U.S Department of Transportation (DOT), U.S. Environmental Protection Agency (EPA), and U.S. Nuclear Regulatory Commission (NRC) regulations; and International Atomic Energy Agency (IAEA) standards and other international documents. The definitions included in this guide may not always be a regulatory definition but are the more common DOE usage. In addition, the definitions vary among regulatory agencies. It is, therefore, suggested that if a definition is to be used in a regulatory or a legal compliance issue, the definition should be verified with the appropriate regulation. To assist in locating definitions in the regulations, a listing of all definition sections in the regulations are included in Appendix B. In many instances, the appropriate regulatory reference is indicated in the right-hand margin

VOLTTRON 3.0: User Guide

Energy Technology Data Exchange (ETDEWEB)

Lutes, Robert G. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Haack, Jereme N. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Katipamula, Srinivas [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Monson, Kyle E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Akyol, Bora A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Carpenter, Brandon J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-11-30

This document is a user guide for the deployment of the transactional network platform and agent/application development within VOLTTRON. The intent of this user guide is to provide a description of the functionality of the transactional network platform. This document describes how to deploy the platform, including installation, use, guidance, and limitations. It also describes how additional features can be added to enhance its current functionality.

VOLTTRON 2.0: User Guide

Energy Technology Data Exchange (ETDEWEB)

Lutes, Robert G. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Haack, Jereme N. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Katipamula, Srinivas [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Monson, Kyle E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Akyol, Bora A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Carpenter, Brandon J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Tenney, Nathan D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2014-11-30

This document is a user guide for the deployment of the transactional network platform and agent/application development within VOLTTRON. The intent of this user guide is to provide a description of the functionality of the transactional network platform. This document describes how to deploy the platform, including installation, use, guidance, and limitations. It also describes how additional features can be added to enhance its current functionality.

Electrodynamic support and/or guide device for a magnetic levitation train. Elektrodynamische Trag- und/oder Fuehrungsvorrichtung fuer eine Magnetschwebebahn

Energy Technology Data Exchange (ETDEWEB)

Lichtenberg, A

1979-02-15

The invention refers to an electrodynamic support and/or guide device for a magnetic levitation train, in which magnets, particularly superconducting magnets are situated on a vehicle, which has rail-like electrically conducting plates or loops on the track. The purpose of the invention is to describe such an electrodynamic support and/or guide device, which can achieve contactless support or guidance of an electrodynamic levitation vehicle when stopped. According to the invention, the problem is solved by the magnetic fields of the support and/or guide magnets acting on the electrically conducting plates or loops of the track being controlled so that moving magnetic fields relative to the vehicle are produced. In this way it is possible to support and/or to guide the vehicle electro-dynamically from standstill to the maximum speed and to drive or brake it.

Guide to preparing SAND reports. Revised

Energy Technology Data Exchange (ETDEWEB)

Locke, T.K. [ed.

1996-04-01

This guide contains basic information needed to produce a SAND report. Its guidelines reflect DOE regulation and Sandia policy. The guide includes basic writing instructions in an annotated sample report; guidance for organization, format, and layout of reports produced by line organizations; and information about conference papers, journal articles, and brochures. The appendixes contain sections on Sandia`s preferred usage, equations, references, copyrights and permissions, and publishing terms.

Study of influence of transport performance of the neutron guide

International Nuclear Information System (INIS)

Li Xinxi; Wang Yan; Huang Chaoqiang; Chen Bo; Chen Liang

2009-01-01

For the sake of improving the performance of the neutron scattering instrument, usually we need use the neutron guide, it's very important to select the right type and optimizing of neutron guide. The papers calculate the focus neutron guide and the single channel neutron guide by numeric method. The results shows that the choice of neutron guide should consult the resolution requirement of neutron scattering instrument, and the length of the neutron guide should be optimized. The calculation results can be the theoretical reference for the design of neutron scattering instrument. (authors)

Guide documentaire pour en savoir plus sur l'informatique (A Documentary Guide to Further Knowledge of Computer Science).

Science.gov (United States)

Achard-Bayle, Guy

1985-01-01

Presents a listing of textbooks, computer program guides, articles, opinion papers, histories, reference works, databases, reviews, bibliographies, organizations, and other information sources concerning computer applications. (MSE)

Consistent guiding center drift theories

International Nuclear Information System (INIS)

Wimmel, H.K.

1982-04-01

Various guiding-center drift theories are presented that are optimized in respect of consistency. They satisfy exact energy conservation theorems (in time-independent fields), Liouville's theorems, and appropriate power balance equations. A theoretical framework is given that allows direct and exact derivation of associated drift-kinetic equations from the respective guiding-center drift-orbit theories. These drift-kinetic equations are listed. Northrop's non-optimized theory is discussed for reference, and internal consistency relations of G.C. drift theories are presented. (orig.)

Errors in the SAP reference model

NARCIS (Netherlands)

Mendling, J.; Aalst, van der W.M.P.; Dongen, van B.F.; Verbeek, H.M.W.

2006-01-01

The SAP Reference Model is a set of information models that is utilized to guide the configuration of SAP systems. A big part of these models are business process models represented in the Eventdriven Process Chains (EPC) notation. These EPC models provide a easy to comprehend overview of SAP

Land-Use History and Contemporary Management Inform an Ecological Reference Model for Longleaf Pine Woodland Understory Plant Communities.

Energy Technology Data Exchange (ETDEWEB)

Brudvig, Lars A. [Department of Plant Biology, Michigan State University; Orrock, John L. [Department of Zoology, University of Wisconsin; Damschen, Ellen I. [Department of Zoology, University of Wisconsin; et al, et al

2014-01-23

Ecological restoration is frequently guided by reference conditions describing a successfully restored ecosystem; however, the causes and magnitude of ecosystem degradation vary, making simple knowledge of reference conditions insufficient for prioritizing and guiding restoration. Ecological reference models provide further guidance by quantifying reference conditions, as well as conditions at degraded states that deviate from reference conditions. Many reference models remain qualitative, however, limiting their utility. We quantified and evaluated a reference model for southeastern U.S. longleaf pine woodland understory plant communities. We used regression trees to classify 232 longleaf pine woodland sites at three locations along the Atlantic coastal plain based on relationships between understory plant community composition, soils lol(which broadly structure these communities), and factors associated with understory degradation, including fire frequency, agricultural history, and tree basal area. To understand the spatial generality of this model, we classified all sites together. and for each of three study locations separately. Both the regional and location-specific models produced quantifiable degradation gradients–i.e., progressive deviation from conditions at 38 reference sites, based on understory species composition, diversity and total cover, litter depth, and other attributes. Regionally, fire suppression was the most important degrading factor, followed by agricultural history, but at individual locations, agricultural history or tree basal area was most important. At one location, the influence of a degrading factor depended on soil attributes. We suggest that our regional model can help prioritize longleaf pine woodland restoration across our study region; however, due to substantial landscape-to-landscape variation, local management decisions should take into account additional factors (e.g., soil attributes). Our study demonstrates the utility

Land-Use History and Contemporary Management Inform an Ecological Reference Model for Longleaf Pine Woodland Understory Plant Communities

Science.gov (United States)

Brudvig, Lars A.; Orrock, John L.; Damschen, Ellen I.; Collins, Cathy D.; Hahn, Philip G.; Mattingly, W. Brett; Veldman, Joseph W.; Walker, Joan L.

2014-01-01

Ecological restoration is frequently guided by reference conditions describing a successfully restored ecosystem; however, the causes and magnitude of ecosystem degradation vary, making simple knowledge of reference conditions insufficient for prioritizing and guiding restoration. Ecological reference models provide further guidance by quantifying reference conditions, as well as conditions at degraded states that deviate from reference conditions. Many reference models remain qualitative, however, limiting their utility. We quantified and evaluated a reference model for southeastern U.S. longleaf pine woodland understory plant communities. We used regression trees to classify 232 longleaf pine woodland sites at three locations along the Atlantic coastal plain based on relationships between understory plant community composition, soils (which broadly structure these communities), and factors associated with understory degradation, including fire frequency, agricultural history, and tree basal area. To understand the spatial generality of this model, we classified all sites together and for each of three study locations separately. Both the regional and location-specific models produced quantifiable degradation gradients–i.e., progressive deviation from conditions at 38 reference sites, based on understory species composition, diversity and total cover, litter depth, and other attributes. Regionally, fire suppression was the most important degrading factor, followed by agricultural history, but at individual locations, agricultural history or tree basal area was most important. At one location, the influence of a degrading factor depended on soil attributes. We suggest that our regional model can help prioritize longleaf pine woodland restoration across our study region; however, due to substantial landscape-to-landscape variation, local management decisions should take into account additional factors (e.g., soil attributes). Our study demonstrates the utility of

Land-use history and contemporary management inform an ecological reference model for longleaf pine woodland understory plant communities.

Directory of Open Access Journals (Sweden)

Lars A Brudvig

Full Text Available Ecological restoration is frequently guided by reference conditions describing a successfully restored ecosystem; however, the causes and magnitude of ecosystem degradation vary, making simple knowledge of reference conditions insufficient for prioritizing and guiding restoration. Ecological reference models provide further guidance by quantifying reference conditions, as well as conditions at degraded states that deviate from reference conditions. Many reference models remain qualitative, however, limiting their utility. We quantified and evaluated a reference model for southeastern U.S. longleaf pine woodland understory plant communities. We used regression trees to classify 232 longleaf pine woodland sites at three locations along the Atlantic coastal plain based on relationships between understory plant community composition, soils (which broadly structure these communities, and factors associated with understory degradation, including fire frequency, agricultural history, and tree basal area. To understand the spatial generality of this model, we classified all sites together and for each of three study locations separately. Both the regional and location-specific models produced quantifiable degradation gradients-i.e., progressive deviation from conditions at 38 reference sites, based on understory species composition, diversity and total cover, litter depth, and other attributes. Regionally, fire suppression was the most important degrading factor, followed by agricultural history, but at individual locations, agricultural history or tree basal area was most important. At one location, the influence of a degrading factor depended on soil attributes. We suggest that our regional model can help prioritize longleaf pine woodland restoration across our study region; however, due to substantial landscape-to-landscape variation, local management decisions should take into account additional factors (e.g., soil attributes. Our study demonstrates

[Guided maxillofacial surgery: Simulation and surgery aided by stereolithographic guides and custom-made miniplates.

Science.gov (United States)

Philippe, B

2013-08-05

We present a new model of guided surgery, exclusively using computer assistance, from the preoperative planning of osteotomies to the actual surgery with the aid of stereolithographic cutting guides and osteosynthetic miniplates designed and made preoperatively, using custom-made titanium miniplates thanks to direct metal laser sintering. We describe the principles that guide the designing and industrial manufacturing of this new type of osteosynthesis miniplates. The surgical procedure is described step-by-step using several representative cases of dento-maxillofacial dysmorphosis. The encouraging short-term results demonstrate the wide range of application of this new technology for cranio-maxillofacial surgery, whatever the type of osteotomy performed, and for plastic reconstructive surgery. Copyright © 2013. Published by Elsevier Masson SAS.

Guide to Choosing Stroke Rehabilitation Services

Science.gov (United States)

National Stroke Association’s Guide to Choosing Stroke Rehabilitation Services Rehabilitation, often referred to as rehab, is an important part of stroke recovery. Through rehab, you:  Re-learn basic skills such ...

A user's guide for the program NAMMU

International Nuclear Information System (INIS)

Wickens, L.M.

1981-09-01

NAMMU is a computer program developed to model single-phase fluid flow in a porous medium. Heat sources may be included if required. Part 1 of this user guide described the program NAMMU in some detail. Here NAMMU is used to solve a specific example problem. The intention is to illustrate the use of the program, highlighting its flexible nature as well as providing a convenient source of information on how to implement NAMMU. The geology, topography and characteristics of the waste repository used in the example are invented just for this illustration and are not representing any real situation. Also, the pathlines calculated and referred to in this paper are for water particles and will not be the same as pathlines for migrating radionuclides. (author)

LADTAP II: technical reference and user guide

International Nuclear Information System (INIS)

Strenge, D.L.; Peloquin, R.A.; Whelan, G.

1986-04-01

This report describes the US Nuclear Regulatory Commission computer program LADTAP II, which performs environmental dose analyses for releases of radioactive effluents from nuclear power plants into surface waters. The analyses estimate radiation dose to individuals, population groups, and biota from ingestion (aquatic foods, water, and terrestrial irrigated foods) and external exposure (shoreline, swimming, and boating) pathways. The calculated doses provide information for National Environmental Policy Act (NEPA) evaluations and for determining compliance with Appendix I of 10 CFR 50 (the ''ALARA'' philosophy). The report also instructs the user in preparing input to the program, describes the mathematical models that are used, and supplies detailed information on program structure and parameters used to modify the program

Biopsy system for CT-guided biopsies

International Nuclear Information System (INIS)

Onik, G.; Cosman, E.; Wells, T.; Goldberg, H.I.; Moss, A.; Costello, P.; Kane, R.

1987-01-01

CT stereotaxic brain biopsies have made brain biopsies safe and minimally invasive. CT-guided biopsies of the body, however, have traditionally used a hand-guidance method. CT biopsy guidance systems for the body have recently become available that have similar capabilities as those of brain biopsy systems. To compare the clinical utility of stereotaxically guided biopsies with hand-guided biopsies, the authors prospectively compared 40 biopsies performed with each method. In the stereotaxic method, a localizor grid was placed on the patient to define a reference point, and a frame was used to guide the needle along the intended path. Computer software programs calculated complex paths from one scan plane to another. Although the results disclosed no significant differences in lesion size or path length between the two groups, the stereotaxically guided biopsies required 75% fewer needle manipulations to hit the intended target. Consequently, the stereotaxically guided biopsies required 40% less time and 80% fewer localization scans to find the biopsy needle than did the hand-guided biopsies

A guide to experimental elementary particle physics literature, 1988--1992. Revision

Energy Technology Data Exchange (ETDEWEB)

Alekhin, S.I.; Ezhela, V.V.; Filimonov, B.B. [Institute for High Energy Physics, Protvino, Moscow Region (Russian Federation)] [and others

1993-09-01

We present an indexed guide to the literature experimental particle physics for the years 1988--1992. About 4,000 papers are indexed by Beam/Target/Momentum, Reaction Momentum (including the final state), Final State Particle, and Accelerator/Detector/Experiment. All indices are cross-referenced to the paper`s title and reference in the ID/Reference/Title Index. The information in this guide is also publicly available from a regularly updated computer database.

Expand your English a guide to improving your academic vocabulary

CERN Document Server

Hart, Steve

2018-01-01

Writing academic prose in English is especially difficult for non-native speakers, largely because the standard vocabulary used in this genre can be quite different from colloquial English. Expand Your English: A Guide to Improving Your Academic Vocabulary is a unique and invaluable guide that will enable the reader to overcome this hurdle. It will become the favourite go-to reference book for both beginners and for intermediate learners struggling with the complexities of English-language academic writing. Steve Hart covers 1,000 vocabulary items that are essential for good academic writing. The first section describes 200 key terms in detail, grouping them into logical sets of 10. Through careful repetition, the reader will find it easy to retain, retrieve, and reuse these essential phrases. The second section explains a further 800 terms, grouping them according to function, meaning, and the areas of an essay where they are likely to be used. The expansive scope of Expand Your English gives non-native spea...

Revised and new national reference values for X-ray diagnostic examinations per 2010

International Nuclear Information System (INIS)

2010-01-01

NRPA has revised the national reference values given in the Guide 5b and established reference values for 10 new investigations. The revision / creation is based on new national dose distributions obtained in the period 2006-2009. Reference values are effective from 27 April 2010. (AG)

Pond and Stream Safari: A Guide to the Ecology of Aquatic Invertebrates.

Science.gov (United States)

Edelstein, Karen

This packet includes a leader's guide, a quick reference guide to aquatic invertebrates, a checklist of common aquatic invertebrates, and activity sheets. The leader's guide includes four sections on background information and seven activities. Background sections include: Understanding Aquatic Insects; Growing Up: Aquatic Insect Forms; Adapting…

LADTAP II: technical reference and user guide

Energy Technology Data Exchange (ETDEWEB)

Strenge, D.L.; Peloquin, R.A.; Whelan, G.

1986-04-01

This report describes the US Nuclear Regulatory Commission computer program LADTAP II, which performs environmental dose analyses for releases of radioactive effluents from nuclear power plants into surface waters. The analyses estimate radiation dose to individuals, population groups, and biota from ingestion (aquatic foods, water, and terrestrial irrigated foods) and external exposure (shoreline, swimming, and boating) pathways. The calculated doses provide information for National Environmental Policy Act (NEPA) evaluations and for determining compliance with Appendix I of 10 CFR 50 (the ''ALARA'' philosophy). The report also instructs the user in preparing input to the program, describes the mathematical models that are used, and supplies detailed information on program structure and parameters used to modify the program.

GASPAR II: Technical reference and user guide

International Nuclear Information System (INIS)

Strenge, D.L.; Bander, T.J.; Soldat, J.K.

1987-03-01

This report describes the computer program GASPAR II used by the staff of the US Nuclear Regulatory Commission to perform environmental dose analyses for releases of radioactive effluents from nuclear power plants into the atmosphere. The analyses estimate radiation dose to individuals and population groups from inhalation, ingestion (terrestrial foods), and external-exposure (ground and plume) pathways. The calculated doses provide information for National Environmental Policy Act (NEPA) evaluations and for determining compliance with Appendix I of 10 CFR 50 (the ''ALARA'' philosophy). The report also instructs the user in preparing input to the program, describes the mathematical models that are used, and supplies detailed information on program structure and parameters used to modify the program. 20 refs., 11 figs., 77 tabs

Testing the Usability of Two Online Research Guides

Directory of Open Access Journals (Sweden)

Luigina Vileno

2011-01-01

Full Text Available This article describes usability testing of two online research guides. One guide was in the area of applied human sciences and the other was geared toward the discipline of psychology. Six undergraduate students were given several tasks to complete by using the guides. The participants also completed two questionnaires. One described the participants’ demographics and how much time they spent on the Internet on a daily basis. On the other questionnaire, filled out after the usability test, the participants rated the online research guides. Overall, the online research guides were found to be difficult to use. By observing how the participants interacted with the online research guides, the author has identified several problem areas that need to be addressed.

A RVI/LAI-reference curve to detect N stress and guide N fertigation using combined information from spectral reflectance and leaf area measurements in potato

DEFF Research Database (Denmark)

Zhenjiang, Zhou; Plauborg, Finn; Thomsen, Anton Gårde

2017-01-01

More user-friendly methods are needed to detect crop N status/stress and guide the timing of in-season N application. In the current study, a reference curve method of detecting N stress was proposed to remedy practical problems of methods that require leaf sampling or maintaining a N sufficient...... was applied during the season. The total N ranged from 0 to180 kg N ha−1. RVI and LAI from the economically optimum 180 kg N ha−1 treatments were used to derive the reference curve. RVI and LAI from 180 kg N ha−1 treatment had a high (R2 = 0.97) correlation and were best fitted with a 2nd order polynomial...... function, which was independent of season. The treatments where N fertigation was stopped before reaching 180 kg N ha−1 started to deviate from the 95% confidence interval of the reference curve about 10 days after N-fertigation was stopped. This corresponded to 10–20 kg ha−1 difference in total plant N...

A guide to data in elementary particle physics

International Nuclear Information System (INIS)

Yost, G.P.; Rittenberg, A.; Armstrong, B.

1986-09-01

We present an indexed guide to experimental high energy physics literature for the years 1977 through 1985. While no actual data are included, approximately 9000 papers are indexed by Beam/Target/Momentum, Reaction/Momentum (including the final state), Particle, and Accelerator/Detector. All indices are cross-referenced via an ID to the paper's title and references in the ID/Reference/Title Index. Black marks (bleeder tabs) at the side of the page enable each section to be located quickly, using the Table of Contents on the back cover. The information presented in this guide is also publicly available on a regularly updated SLAC-SPIRES database called DATAGUIDE

Enterprise Reference Library

Science.gov (United States)

Bickham, Grandin; Saile, Lynn; Havelka, Jacque; Fitts, Mary

2011-01-01

Introduction: Johnson Space Center (JSC) offers two extensive libraries that contain journals, research literature and electronic resources. Searching capabilities are available to those individuals residing onsite or through a librarian s search. Many individuals have rich collections of references, but no mechanisms to share reference libraries across researchers, projects, or directorates exist. Likewise, information regarding which references are provided to which individuals is not available, resulting in duplicate requests, redundant labor costs and associated copying fees. In addition, this tends to limit collaboration between colleagues and promotes the establishment of individual, unshared silos of information The Integrated Medical Model (IMM) team has utilized a centralized reference management tool during the development, test, and operational phases of this project. The Enterprise Reference Library project expands the capabilities developed for IMM to address the above issues and enhance collaboration across JSC. Method: After significant market analysis for a multi-user reference management tool, no available commercial tool was found to meet this need, so a software program was built around a commercial tool, Reference Manager 12 by The Thomson Corporation. A use case approach guided the requirements development phase. The premise of the design is that individuals use their own reference management software and export to SharePoint when their library is incorporated into the Enterprise Reference Library. This results in a searchable user-specific library application. An accompanying share folder will warehouse the electronic full-text articles, which allows the global user community to access full -text articles. Discussion: An enterprise reference library solution can provide a multidisciplinary collection of full text articles. This approach improves efficiency in obtaining and storing reference material while greatly reducing labor, purchasing and

FAA Offers Free Guide on Elementary Aviation Education.

Science.gov (United States)

Journal of Aerospace Education, 1978

1978-01-01

Describes a teaching guide in aviation education for grades 2 through 6. The guide contains activities designed to enrich an existing science curriculum. An address for ordering the guide is included. (MA)

A field guide to digital color

CERN Document Server

Stone, Maureen

2013-01-01

Maureen Stone's field guide to digital color presents a survey of digital color with special emphasis on those fields important for computer graphics. The book provides the foundation for understanding color and its applications, discusses color media and color management and the use of color in computer graphics, including color design and selection. The book provides a guide for anyone who wants to understand and apply digital color. An annotated bibliography provides in-depth references for further study on each topic.

Computer Assisted Drafting (CNC) Drawings. Drafting Module 6. Instructor's Guide.

Science.gov (United States)

Missouri Univ., Columbia. Instructional Materials Lab.

This Missouri Vocational Instruction Management System instructor's drafting guide has been keyed to the drafting competency profile developed by state industry and education professionals. This unit contains information on computer-assisted drafting drawings. The guide contains a cross-reference table of instructional materials and 20 worksheets.…

Making sense of business reference a guide for librarians and research professionals

CERN Document Server

Ross, Celia

2013-01-01

A detailed bibliography functions as both a standing reference for desk use as well as a collection development aid for building a core business collection. Including numerous illustrative case studies, Making Sense of Business Reference takes the guesswork out of doing business.

DOE interpretations Guide to OSH standards. Update to the Guide

Energy Technology Data Exchange (ETDEWEB)

1994-03-31

Reflecting Secretary O`Leary`s focus on occupational safety and health, the Office of Occupational Safety is pleased to provide you with the latest update to the DOE Interpretations Guide to OSH Standards. This Guide was developed in cooperation with the Occupational Safety and Health Administration, which continued it`s support during this last revision by facilitating access to the interpretations found on the OSHA Computerized Information System (OCIS). This March 31, 1994 update contains 123 formal in letter written by OSHA. As a result of the unique requests received by the 1-800 Response Line, this update also contains 38 interpretations developed by DOE. This new occupational safety and health information adds still more important guidance to the four volume reference set that you presently have in your possession.

DOE interpretations Guide to OSH standards. Update to the Guide

Energy Technology Data Exchange (ETDEWEB)

1994-03-31

Reflecting Secretary O`Leary`s focus on occupational safety and health, the Office of Occupational Safety is pleased to provide you with the latest update to the DOE Interpretations Guide to OSH Standards. This Guide was developed in cooperation with the Occupational Safety and Health Administration, which continued its support during this last revision by facilitating access to the interpretations found on the OSHA Computerized Information System (OCIS). This March 31, 1994 update contains 123 formal interpretation letters written by OSHA. As a result of the unique requests received by the 1-800 Response Line, this update also contains 38 interpretations developed by DOE. This new occupational safety and health information adds still more important guidance to the four volume reference set that you presently have in your possession.

DOE interpretations Guide to OSH standards. Update to the Guide

Energy Technology Data Exchange (ETDEWEB)

1994-03-31

Reflecting Secretary O`Leary`s focus on occupational safety and health, the Office of Occupational Safety is pleased to provide you with the latest update to the DOE Interpretations Guide to OSH Standards. This Guide was developed in cooperation with the Occupational Safety and Health Administration, which continued its support during this last revision by facilitating access to the interpretations found on the OSHA Computerized Information System (OCIS). This March 31, 1994 update contains 123 formal interpretation letters written OSHA. As a result of the unique requests received by the 1-800 Response Line, this update also contains 38 interpretations developed by DOE. This new occupational safety and health information adds still more important guidance to the four volume reference set that you presently have in your possession.

Guides for intraoral x-rays

International Nuclear Information System (INIS)

Ogunsunlade, O.A.

1988-01-01

An h-shaped exterior guide for use in combination with a SNAP-A-RAY film holder for accurately aligning a beam from an X-ray cone with an X-ray film during the process of taking intraoral periapical dental X-rays of the maxillary and mandibular teeth is described comprising: a first guide arm laterally and detachably connectable through a housing means; a traverse arm extending from the midpoint of the first guide arm and parallel to the X-ray film; and a second guide arm extending perpendicularly from an end of the traverse arm toward a plane of the X-ray film and in parallel relation up to an end point of the first guide arm

Standard digital reference images for titanium castings

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 The digital reference images provided in the adjunct to this standard illustrate various types and degrees of discontinuities occurring in titanium castings. Use of this standard for the specification or grading of castings requires procurement of the adjunct digital reference images, which illustrate the discontinuity types and severity levels. They are intended to provide the following: 1.1.1 A guide enabling recognition of titanium casting discontinuities and their differentiation both as to type and degree through digital radiographic examination. 1.1.2 Example digital radiographic illustrations of discontinuities and a nomenclature for reference in acceptance standards, specifications and drawings. 1.2 The digital reference images consist of seventeen digital files each illustrating eight grades of increasing severity. The files illustrate seven common discontinuity types representing casting sections up to 1-in. (25.4-mm). 1.3 The reference radiographs were developed for casting sections up to 1...

Theatre and Cinema Architecture: A Guide to Information Sources.

Science.gov (United States)

Stoddard, Richard

This annotated bibliography cites works related to theatres, movie houses, opera houses, and dance facilities. It is divided into three parts: general references, theatre architecture, and cinema architecture. The part on general references includes bibliographies and periodicals. The second and main part of the guide, on theatre architecture,…

Pre-Calculus Instructional Guide for Elementary Functions, Analytic Geometry.

Science.gov (United States)

Montgomery County Public Schools, Rockville, MD.

This is a guide for use in semester-long courses in Elementary Functions and Analytic Geometry. A list of entry-level skills and a list of approved textbooks is provided. Each of the 18 units consists of: (1) overview, suggestions for teachers, and suggested time; (2) list of objectives; (3) cross-references guide to approved textbooks; (4) sample…

JavaScript The Definitive Guide

CERN Document Server

Flanagan, David

2011-01-01

Since 1996, JavaScript: The Definitive Guide has been the bible for JavaScript programmers-a programmer's guide and comprehensive reference to the core language and to the client-side JavaScript APIs defined by web browsers. The 6th edition covers HTML5 and ECMAScript 5. Many chapters have been completely rewritten to bring them in line with today's best web development practices. New chapters in this edition document jQuery and server side JavaScript. It's recommended for experienced programmers who want to learn the programming language of the Web, and for current JavaScript programmers wh

NPAS Users Guide

International Nuclear Information System (INIS)

1984-01-01

This NPAS Users Guide is primarily intended as a source of information about policies, procedures, and facilities appropriate for users in the program of Nuclear Physics at SLAC (NPAS). General policies and practices are described, the preparation of proposals is discussed, and the services for users is outlined. SLAC experimental facilities are described, and contacts are listed

U.S. Arctic Voyage Planning Guide (AVPG)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Arctic Voyage Planning Guide is a compilation of official U.S. Government information and references to sources of information that may be consulted by mariners...

Changing quantum reference frames

OpenAIRE

Palmer, Matthew C.; Girelli, Florian; Bartlett, Stephen D.

2013-01-01

We consider the process of changing reference frames in the case where the reference frames are quantum systems. We find that, as part of this process, decoherence is necessarily induced on any quantum system described relative to these frames. We explore this process with examples involving reference frames for phase and orientation. Quantifying the effect of changing quantum reference frames serves as a first step in developing a relativity principle for theories in which all objects includ...

Your Guide to Meebo Options: Virtual Reference Summer Meltdown and Fall Shakeout

Science.gov (United States)

Breitbach, William

2012-01-01

Competition in the virtual reference market got really hot this past summer. Recent developments in virtual reference offerings suggest the market is much more dynamic than most people would have imagined a short time ago. With Google's acquisition of Meebo and its subsequent decision to shut down the chat widget service, many libraries scrambled…

Invasive Plants Field and Reference Guide: An Ecological Perspective of Plant Invaders of Forests and Woodlands

Science.gov (United States)

Cynthia D. Huebner; Cassandra Olson; Heather C. Smith; Heather C. Smith

2005-01-01

There are many field guides available about invasive plants and their identification. The purpose of this particular field guide is to give a scientific synthesis of what is known about the behavior of such species in managed, disturbed, and pristine forested systems in addition to key information for accurate identification.

Preparation and characterization of the fish reference material; Preparacao e caracterizacao de um material de referencia de peixe

Energy Technology Data Exchange (ETDEWEB)

Ulrich, Joao Cristiano

2011-07-01

The certified reference materials (CRMs) play an important role in obtaining measurement results traceable to the International System of Units, through an unbroken chain of comparisons. Thus, the demand for new certified reference materials (CRMs) increases every day in all areas of knowledge. The availability of reference materials, mainly in Brazil is still incipient, given that the demand far exceeds the available variety of these materials. The amount of certified reference materials available in the country is insufficient to meet the need of the scientific community and demands for development of new methodologies. Among the many areas in need of reference materials, we highlight the importance for the food trade balance for these products within the country. The certification of food products, intended both for export and for domestic consumption, requires analysis methods that provide precise and accurate results to ensure product quality. This paper describes the preparation and certification of a reference material in the fish matrix in mercury and methylmercury. The study brings together since the stage of material selection, preparation, development of homogeneity and stability studies and characterization. The certification was performed by means of measurements using two analytical techniques, flow injection analysis - cold vapor atomic absorption spectrometry (FIA-CV-AAS) and isotope dilution applied to mass spectrometry (IDMS), which is a primary method. In this work the standards of the ISO 30 (ABNT 30-34) and ISO Guide 35 was used as the basis for the preparation and characterization of the material. For the calculation of uncertainties was used the GUM and Eurachem guide. As a result, was produced and certified a lot of material in relation to the concentration of mercury (Hg = 0.271 {+-} 0.057 mg g{sup -1}) and methylmercury (MeHg = 0.245 {+-} 0.038 mg g{sup -1}), and informational values of lead and arsenic. (author)

EUS-guided recanalization of complete gastrointestinal strictures

Directory of Open Access Journals (Sweden)

Miguel Martínez-Guillén

Full Text Available Background and aim: Complete gastrointestinal strictures are a technically demanding problem. In this setting, an anterograde technique is associated with a high risk of complications and a combined anterograde-retrograde technique requires a prior ostomy. Our aim was to assess the outcome of a first case series for the management of complete gastrointestinal strictures using endoscopic ultrasound (EUS-guided puncture as a novel endoscopic approach. Patients and methods: This retrospective case-series describes four cases that were referred for treatment of complete benign gastrointestinal strictures, three upper and one lower. Recanalization was attempted with EUS-guided puncture using a 22G or 19G needle and contrast filling was visualized by fluoroscopy. Afterwards, a cystotome and/or a dilator balloon were used under endoscopic and fluoroscopic guidance. A fully covered metal stent was placed in two cases, keeping the strictures open in order to prevent another stricture. Feasibility, adverse events, efficacy and the number of dilations required after recanalization were evaluated. Results: Technical and clinical success was achieved in three of the four cases (75%. A first dilation was performed using a dilator balloon in all successful cases and fully covered metal stents were used in two cases. These patients underwent a consecutive number of balloon dilatations (range 1-4 and all three were able to eat a soft diet. No adverse events were related to the EUS-guided approach. In the failed case with a long stricture (> 3 cm, an endoscopic rendezvous technique was attempted which caused a pneumothorax requiring a chest tube placement. Conclusion: EUS-guided recanalization, as a first approach in the treatment of complete digestive stricture, is a feasible and promising procedure that can help to avoid major surgery.

Event boundaries and anaphoric reference.

Science.gov (United States)

Thompson, Alexis N; Radvansky, Gabriel A

2016-06-01

The current study explored the finding that parsing a narrative into separate events impairs anaphor resolution. According to the Event Horizon Model, when a narrative event boundary is encountered, a new event model is created. Information associated with the prior event model is removed from working memory. So long as the event model containing the anaphor referent is currently being processed, this information should still be available when there is no narrative event boundary, even if reading has been disrupted by a working-memory-clearing distractor task. In those cases, readers may reactivate their prior event model, and anaphor resolution would not be affected. Alternatively, comprehension may not be as event oriented as this account suggests. Instead, any disruption of the contents of working memory during comprehension, event related or not, may be sufficient to disrupt anaphor resolution. In this case, reading comprehension would be more strongly guided by other, more basic language processing mechanisms and the event structure of the described events would play a more minor role. In the current experiments, participants were given stories to read in which we included, between the anaphor and its referent, either the presence of a narrative event boundary (Experiment 1) or a narrative event boundary along with a working-memory-clearing distractor task (Experiment 2). The results showed that anaphor resolution was affected by narrative event boundaries but not by a working-memory-clearing distractor task. This is interpreted as being consistent with the Event Horizon Model of event cognition.

Manual on panoramic gamma irradiators (categories 2 and 4). Incorporating: Applications guide, procedures guide, basics guide

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The document is the first revision of a previous one published in 1993 to provide guidance on the safe use and regulation of self-contained gamma irradiators (Co-60 or Cs-137 sources) in different fields of application. It includes three parts: Applications Guide, which describes the main applications of self-contained gamma irradiators, the type of equipment, including safety systems, operation and maintenance, and how to deal with incidents. Procedures Guide, which gives step by step instructions on how to carry out the practice. Basics Guide, which explains the fundamentals of radiation, the system of units, interaction of radiation with matter radiation detection, etc. The manual is aimed primarily at persons handling such radiation sources on a daily routine basis, as well as at the competent authorities for training of workers in radiation protection or for setting up local radiation protection rules.

Manual on panoramic gamma irradiators (categories 2 and 4). Incorporating: Applications guide, procedures guide, basics guide

International Nuclear Information System (INIS)

1996-01-01

The document is the first revision of a previous one published in 1993 to provide guidance on the safe use and regulation of self-contained gamma irradiators (Co-60 or Cs-137 sources) in different fields of application. It includes three parts: Applications Guide, which describes the main applications of self-contained gamma irradiators, the type of equipment, including safety systems, operation and maintenance, and how to deal with incidents. Procedures Guide, which gives step by step instructions on how to carry out the practice. Basics Guide, which explains the fundamentals of radiation, the system of units, interaction of radiation with matter radiation detection, etc. The manual is aimed primarily at persons handling such radiation sources on a daily routine basis, as well as at the competent authorities for training of workers in radiation protection or for setting up local radiation protection rules

A GUIDE TO INSTRUCTIONAL TELEVISION.

Science.gov (United States)

DIAMOND, ROBERT M., ED.

THIS IS A GUIDE DESIGNED AS A SINGLE REFERENCE FOR ADMINISTRATORS, TEACHERS, STUDENTS, AND LAYMEN INTERESTED IN TELEVISION FOR A SPECIFIC SCHOOL OR SCHOOL SYSTEM. FOUR EXAMPLES OF SINGLE-ROOM TELEVISION ARE GIVEN AND SUCCESSFUL APPLICATIONS OF STUDIO TELEVISION ARE PRESENTED. ITS USE IN GUIDANCE AND IN ADMINISTRATION IS EXPLAINED. THE PROBLEMS…

Security programs for Category I or II nuclear material or certain nuclear facilities. Regulatory guide G-274

International Nuclear Information System (INIS)

2003-03-01

The purpose of this regulatory guide is to help applicants for a Canadian Nuclear Safety Commission (CNSC) licence in respect of Category I or II nuclear material - other than a licence to transport - , or a nuclear facility consisting of a nuclear reactor that may exceed 10 MW thermal power during normal operation, prepare and submit the security information to be included with the application, pursuant to the Nuclear Safety and Control Act (NSCA). Category I and II nuclear material are defined in Appendix B to this guide. This guide describes: the security information that should typically be included with the application for any licence referred to above; how the security information may be organized and presented in a separate document (hereinafter 'the security program description'), in order to assist CNSC review and processing of the application; and, the administrative procedures to be followed when preparing, submitting or revising the security program description. (author)

Using the Language of Sets to Describe Nested Systems in Emergy Evaluations

Science.gov (United States)

The language of set theory has been recently used to describe the emergy evaluation of a process. In this paper this mathematical language is used as a guide to evaluate the emergy of nested systems. We analyze a territorial system on multiple scales as an example of hierarchical...

Discussion on the re-irradiated fuel assembly with damaged guide vanes

International Nuclear Information System (INIS)

Li Ligang

2013-01-01

In January 2011, during the second plant of CNNC Nuclear Power Operations Management Co., Ltd.(hereinafter referred to as the second plant) refueling outage, the visual inspection found the guide vanes of fuel assembly A had felling off. After the National Nuclear Safety Administration (NNSA) estimated and approved, the fuel assembly A was reloaded in the specified location of reactor core. During the refueling outage in March 2012, the fuel assembly A was removed again from the reactor core. Visual inspection confirmed that the fuel assembly A was complete and without abnormal changes. The practice provides reference for re-irradiated of fuel assembly with the same type of damaged guide vanes, and provides case support for standard development for the same type of re-irradiated fuel assembly with damaged guide vanes. (author)

Reference handbook: Level detectors

International Nuclear Information System (INIS)

1990-01-01

The purpose of this handbook is to provide Rocky Flats personnel with the information necessary to understand level measurement and detection. Upon completion of this handbook you should be able to do the following: List three reasons for measuring level. Describe the basic operating principles of the sight glass. Demonstrate proper techniques for reading a sight glass. Describe the basic operating principles of a float level detector. Describe the basic operating principles of a bubbler level indicating system. Explain the differences between a wet and dry reference leg indicating system, and describe how each functions. This handbook is designed for use by experienced Rocky Flats operators to reinforce and improve their current knowledge level, and by entry-level operators to ensure that they possess a minimum level of fundamental knowledge. Level Detectors is applicable to many job classifications and can be used as a reference for classroom work or for self-study. Although this reference handbook is by no means all-encompassing, you will gain enough information about this subject area to assist you in contributing to the safe operation of Rocky Flats Plant

Guide to Federal Career Literature: 1976.

Science.gov (United States)

Civil Service Commission, Washington, DC.

The publication is designed to serve as a reference guide to Federal recruiting literature. It contains brief descriptions of publications of 43 departments and agencies. The pamphlets and brochures listed represent the principle publications used in nationwide recruiting for college entry-level positions. The bibliography is organized…

STL pocket reference

CERN Document Server

Lischner, Ray

2003-01-01

The STL Pocket Reference describes the functions, classes, and templates in that part of the C++ standard library often referred to as the Standard Template Library (STL). The STL encompasses containers, iterators, algorithms, and function objects, which collectively represent one of the most important and widely used subsets of standard library functionality. The C++ standard library, even the subset known as the STL, is vast. It's next to impossible to work with the STL without some sort of reference at your side to remind you of template parameters, function invocations, return types--ind

Service level agreements a legal and practical guide

CERN Document Server

Desai, Jimmy

2010-01-01

By reading this a short, legal and practical guide to SLAs, you should be able to quickly come up to speed with some of the legal and practical issues that might arise. Negotiating the SLA and putting the SLA into action are also discussed in the pocket guide. Whilst short and easy to digest, case references and weblinks have been provided in the text so readers can find out more information about SLAs.  

User Guide for Automated Wetland Determination Data Sheets

Science.gov (United States)

2017-07-25

are not visible to the user . As a result, it is important that users open a fresh copy of the Excel® file for every use and ensure that macros are...input on the ADS and this user guide. REFERENCES Berkowitz, J. F. 2011a. Regionalizing the Corps of Engineers wetland delineation manual : Process...Wetlands Regulatory Assistance Program ERDC/TN WRAP-17-1 July 2017 Approved for public release; distribution is unlimited. User Guide for

Human reliability assessors guide: an overview

International Nuclear Information System (INIS)

Humphreys, P.

1988-01-01

The Human Reliability Assessors Guide 1 provides a review of techniques currently available for the quantification of Human Error Probabilities. The Guide has two main objectives. The first is to provide a clear and comprehensive description of eight major techniques which can be used to assess human reliability. This is supplemented by case studies taken from practical applications of each technique to industrial problems. The second objective is to provide practical guidelines for the selection of techniques. The selection process is aided by reference to a set of criteria against which each of the eight techniques have been evaluated. Utilising the criteria and critiques, a selection method is presented. This is designed to assist the potential user in choosing the technique, or combination of techniques, most suited to answering the users requirements. For each of the eight selected techniques, a summary of the origins of the technique is provided, together with a method description, detailed case studies, abstracted case studies and supporting references. (author)

JavaScript Pocket Reference

CERN Document Server

Flanagan, David

1998-01-01

JavaScript is a powerful, object-based scripting language that can be embedded directly in HTML pages. It allows you to create dynamic, interactive Web-based applications that run completely within a Web browser -- JavaScript is the language of choice for developing Dynamic HTML (DHTML) content. JavaScript can be integrated effectively with CGI and Java to produce sophisticated Web applications, although, in many cases, JavaScript eliminates the need for complex CGI scripts and Java applets altogether. The JavaScript Pocket Reference is a companion volume to JavaScript: The Definitive Guide

ENRAF gauge reference level calculations

Energy Technology Data Exchange (ETDEWEB)

Huber, J.H., Fluor Daniel Hanford

1997-02-06

This document describes the method for calculating reference levels for Enraf Series 854 Level Detectors as installed in the tank farms. The reference level calculation for each installed level gauge is contained herein.

Users guide for the ANL IBM SPx

Energy Technology Data Exchange (ETDEWEB)

Gropp, W.; Lusk, E.

1994-12-01

This guide presents the features of the IBM SPx installed in the Mathematics and Computer Science Division at Argonne National Laboratory. The guide describes the available hardware and software, access policies, and hints for using the system productively.

Urban Agriculture Guide

NARCIS (Netherlands)

Visser, A.J.; Jansma, J.E.; Dekking, A.J.G.; Klieverik, M.J.M.

2007-01-01

The Urban Agriculture Guide describes the experiences, learning moments, tips and tricks of those involved in the initiatives of urban agriculture and an indication is provided of what is required to develop urban agriculture further in the Netherlands

Destination: Marshall Islands. Video Guide.

Science.gov (United States)

Legowski, Margaret

This video guide was developed by the Peace Corps' Office of World Wise Schools. Activities that the guide describes are for use in a 3- to 5-day unit on one of the nations of Oceania, the Republic of the Marshall Islands. The activities are designed to provide students with opportunities to: (1) compare and contrast Marshallese and U.S. culture;…

ALA Fingertip Guide to National Health-Information Resources. 1995-1996 Reference Desk Edition.

Science.gov (United States)

Kovacs, Beatrice

In response to a growing need for personal health and fitness information, this guide provides the telephone numbers and addresses of organizations serving public information interests. Features include: alphabetical entries for 404 organizations from AIDS Clinical Trials Information Service, Air Ambulance America to Visiting Nurse Association of…

Your Environment: A Guide for Students.

Science.gov (United States)

Florida State Dept. of Environmental Protection, Tallahassee.

This environmental guide for students contains stories on air pollution, water pollution, wetlands, groundwater, solid and hazardous waste, and coastal areas. It includes a section on how students can help Florida's environment. A reference section with contact names and addresses for Florida's governmental and citizen organizations is also…

Guide to the collision avoidance rules

CERN Document Server

Cockcroft, A N

2004-01-01

A Guide to the Collision Avoidance Rules is the essential reference to the safe operation of all vessels at sea. Published continuously since 1965, this respected and expert guide is the classic text for all who need to, practically and legally, understand and comply with the Rules. This sixth edition incorporates all of the amendments to the International Regulations for Preventing Collisions at Sea which came into force in November 2003.The books sets out all of the Rules with clear explanation of their meaning, and gives detailed examples of how the rules have been used in practice

Guide for disposition of radioactive-material sources

International Nuclear Information System (INIS)

Taylor, J.M.; Selby, J.M.

1983-04-01

This guide has been prepared to assist DOE Energy Technology Centers in disposing of radioactive-material sources. The guide describes the steps and requirements necessary to dispose of unwanted sources. The steps include obtaining approvals, source characterization, source disposition, packaging requirements, and shipment preparation. A flow chart is provided in the guide to assist the user in the necessary sequential steps of source disposition

Probabilistic safety analysis procedures guide, Sections 8-12. Volume 2, Rev. 1

International Nuclear Information System (INIS)

McCann, M.; Reed, J.; Ruger, C.; Shiu, K.; Teichmann, T.; Unione, A.; Youngblood, R.

1985-08-01

A procedures guide for the performance of probabilistic safety assessment has been prepared for interim use in the Nuclear Regulatory Commission programs. It will be revised as comments are received, and as experience is gained from its use. The probabilistic safety assessment studies performed are intended to produce probabilistic predictive models that can be used and extended by the utilities and by NRC to sharpen the focus of inquiries into a range of issues affecting reactor safety. The first volume of the guide describes the determination of the probability (per year) of core damage resulting from accident initiators internal to the plant (i.e., intrinsic to plant operation) and from loss of off-site electric power. The scope includes human reliability analysis, a determination of the importance of various core damage accident sequences, and an explicit treatment and display of uncertainties for key accident sequences. This second volume deals with the treatment of the so-called external events including seismic disturbances, fires, floods, etc. Ultimately, the guide will be augmented to include the plant-specific analysis of in-plant processes (i.e., containment performance). This guide provides the structure of a probabilistic safety study to be performed, and indicates what products of the study are valuable for regulatory decision making. For internal events, methodology is treated in the guide only to the extent necessary to indicate the range of methods which is acceptable; ample reference is given to alternative methodologies which may be utilized in the performance of the study. For external events, more explicit guidance is given

The Internet for Educators: A User's Guide.

Science.gov (United States)

Monahan, Brian D.; Dharm, Matthew

1995-01-01

Presents a practical guide to use of the Internet. Topics discussed include getting connected; the UNIX operating system; electronic mail; FTP (File Transfer Protocol); Finger; Telnet; Archie; Veronica; Gopher; teacher education; the Yanoff List; and expansion of the Internet. (three references) (LRW)

Long-term pavement performance ancillary information management system (AIMS) reference guide.

Science.gov (United States)

2012-11-01

This document provides information on the Long-Term Pavement Performance (LTPP) program ancillary information. : Ancillary information includes data, images, reference materials, resource documents, and other information that : support and extend the...

Manual on self-contained gamma irradiators (categories 1 and 3). Incorporating: Applications guide, procedures guide, basics guide

International Nuclear Information System (INIS)

1996-01-01

The document is the first revision of a previous one published in 1993 to provide guidance on the safe use and regulation of panoramic gamma irradiators (Co-60 or Cs-137 sources) in different fields of application. It includes three parts: Applications Guide, which describes the main applications of panoramic gamma irradiators, the type of equipment, including safety systems, operation and maintenance, and how to deal with incidents. Procedures Guide, which gives step by step instructions on how to carry out the practice. Basics Guide, which explains the fundamentals of radiation, the system of units, interaction of radiation with matter radiation detection, etc. and which is common to all documents in the series. The manual is aimed primarily at persons handling such radiation sources on a daily routine basis, as well as at the competent authorities for training of workers in radiation protection or for setting up local radiation protection rules

Comparison of Radial Access, Guided Femoral Access, and Non-Guided Femoral Access Among Women Undergoing Percutaneous Coronary Intervention.

Science.gov (United States)

Koshy, Linda M; Aberle, Laura H; Krucoff, Mitchell W; Hess, Connie N; Mazzaferri, Ernest; Jolly, Sanjit S; Jacobs, Alice; Gibson, C Michael; Mehran, Roxana; Gilchrist, Ian C; Rao, Sunil V

2018-01-01

This study was conducted to determine the association between radial access, guided femoral access, and non-guided femoral access on postprocedural bleeding and vascular complications after percutaneous coronary intervention (PCI). Bleeding events and major vascular complications after PCI are associated with increased morbidity, mortality, and cost. While the radial approach has been shown to be superior to the femoral approach in reducing bleeding and vascular complications, whether the use of micropuncture, fluoroscopy, or ultrasound mitigates these differences is unknown. We conducted a post hoc analysis of women in the SAFE-PCI for Women trial who underwent PCI and had the access method identified (n = 643). The primary endpoint of postprocedure bleeding or vascular complications occurring within 72 hours or at discharge was adjudicated by an independent clinical events committee and was compared based on three categories of access technique: radial, guided femoral (fluoroscopy, micropuncture, ultrasound), or non-guided femoral (none of the aforementioned). Differences between the groups were determined using multivariate logistic regression using radial access as the reference. Of the PCI population, 330 underwent radial access, 228 underwent guided femoral access, and 85 underwent non-guided femoral access. There was a statistically significant lower incidence of the primary endpoint with radial access vs non-guided femoral access; however, there was no significant difference between radial approach and femoral access guided by fluoroscopy, micropuncture, or ultrasound. This post hoc analysis demonstrates that while radial access is safer than non-guided femoral access, guided femoral access appears to be associated with similar bleeding events or vascular complications as radial access.

Neuwirth RJ, Svetlicinii A and De Castro Halis D (eds) The BRICS-Lawyers' Guide to Global Cooperation (Cambridge University Press 2017)

OpenAIRE

Sucker, F

2018-01-01

This contribution reviews the book The BRICS-Lawyers' Guide to Global Cooperation edited by Rostam J Neuwirth, Alexandr Svetlicinii and Denis De Castro Halis. It was published by Cambridge University Press in 2017, and deals with aspects of international trade and development involving the BRICS area -Brazil, Russia, India, China and South Africa. It is described as a unique reference book for academics, governmental officials, legal professionals, business executives, researchers and students.

Seismic Safety Guide

International Nuclear Information System (INIS)

Eagling, D.G.

1985-01-01

The Seismic Safety Guide provides facilities managers with practical guidelines for administering a comprehensive earthquake safety program. Most facilities managers, unfamiliar with earthquake engineering, tend to look for answers in techniques more sophisticated than required to solve the actual problems in earthquake safety. Often the approach to solutions to these problems is so academic, legalistic, and financially overwhelming that mitigation of actual seismic hazards simply does not get done in a timely, cost-effective way. The objective of the Guide is to provide practical advice about earthquake safety so that managers and engineers can get the job done without falling into common pitfalls, prolonged diagnosis, and unnecessary costs. It is comprehensive with respect to earthquakes in that it covers the most important aspects of natural hazards, site planning, rehabilitation of existing buildings, design of new facilities, operational safety, emergency planning, non-structural elements, life lines, and risk management. 5 references

PCs all-in-one desk reference for dummies

CERN Document Server

Chambers, Mark L

2013-01-01

Need the scoop on Windows Vista? How about Office 2007? Anything you need to know about using your PC can probably be found in PCs All-In-One Desk Reference for Dummies, 4th Edition. This handy guide is made up of eight convenient minibooks, so you can find what you need in a hurry. And in case you think you've seen it before, this fourth edition is fully updated for all the newest, coolest stuff. Want a guided tour of the Vista operating system and how it differs from XP? Check out minibook #2. Have you heard about Microsoft Works but aren't sure what it's about? Find out

SharePoint Office Pocket Guide

CERN Document Server

Webb, Jeff

2009-01-01

With this handy reference as your guide, you can reap all the benefits of SharePoint--Microsoft's amazing information-sharing tool. It shows you, in plain language, how to construct a web site where individuals from all over can capture and share ideas. Learn how to upload documents, edit content, send alerts, track work items, add new team members, and much more.

Revision of the protective action guides manual for nuclear incidents

International Nuclear Information System (INIS)

DeCair, S.; MacKinney, J.

2007-01-01

EPA's 1992 Manual of Protective Action Guides and Protective Actions for Nuclear Incidents, referred to as the PAG Manual, is a radiological emergency planning and response tool for emergency management officials at the Federal, state, tribal, and local levels. A Protective Action Guide is defined as, the projected dose to reference man, or other defined individual, from a release of radioactive material at which a specific protective action to reduce or avoid that dose is recommended'. The updated version of the PAG Manual accomplishes these key objectives: applying the existing 1992 protective action guides and protective actions to new radiological and nuclear scenarios of concern; updating the dosimetry basis; lowering the recommended dose for administration of stable iodine; providing new guidance concerning consumption of drinking water during or after a radiological emergency; updating the dosimetry basis for all derived levels, and, adding guidance for dealing with long-term site restoration following a major radiological release. (author)

Lexically guided perceptual learning in Mandarin Chinese

NARCIS (Netherlands)

Burchfield, L.A.; Luk, S.H.K.; Antoniou, M.; Cutler, A.

2017-01-01

Lexically guided perceptual learni ng refers to the use of lexical knowledge to retune sp eech categories and thereby adapt to a novel talker's pronunciation. This adaptation has been extensively documented, but primarily for segmental-based learning in English and Dutch. In languages with lexical

Mars Global Reference Atmospheric Model 2010 Version: Users Guide

Science.gov (United States)

Justh, H. L.

2014-01-01

This Technical Memorandum (TM) presents the Mars Global Reference Atmospheric Model 2010 (Mars-GRAM 2010) and its new features. Mars-GRAM is an engineering-level atmospheric model widely used for diverse mission applications. Applications include systems design, performance analysis, and operations planning for aerobraking, entry, descent and landing, and aerocapture. Additionally, this TM includes instructions on obtaining the Mars-GRAM source code and data files as well as running Mars-GRAM. It also contains sample Mars-GRAM input and output files and an example of how to incorporate Mars-GRAM as an atmospheric subroutine in a trajectory code.

Style Guide: An Interdisciplinary Communication Tool to Support the Process of Generating Tailored Infographics From Electronic Health Data Using EnTICE3.

Science.gov (United States)

Arcia, Adriana; Velez, Mark; Bakken, Suzanne

2015-01-01

In this case study we describe key features of the structured communication tool-a style guide-used to support interdisciplinary collaboration, and we propose the use of such a tool for research teams engaged in similar projects. We employ tailored infographics to present patient reported outcome data from a community health survey back, in a comprehensible and actionable manner, to the individuals who provided it. The style guide was developed to bridge the semantic gap between the domain and programming experts engaged in this effort. The style guide supports the communication of complex design specifications in a highly structured format that is nevertheless flexible enough to accommodate project growth. Unlike the typical corporate style guide that has a more narrative format, our style guide is innovative in its use of consistent fields across multiple, standalone entries. The process of populating the style guide prompted the designer toward greater design efficiency and led to consistent and specific instructions that met the framework architect's stated information needs. The guiding values in the creation of the style guide were consistency, clarity, and flexibility. It serves as a durable reference to the desired look and functionality of the final infographic product without dictating an implementation strategy. The style guide format can be adapted to meet the communication needs of other interdisciplinary teams facing a semantic gap.

Reference serving sizes for the Brazilian population: An analysis of processed food labels

Directory of Open Access Journals (Sweden)

Nathalie Kliemann

2014-06-01

Full Text Available OBJECTIVE: To compare serving sizes reported on processed food labels with reference serving sizes according to nutrition labeling legislation and the "Food Guide for the Brazilian Population". METHODS: This cross-sectional study analyzed the labels of 2,072 processed foods in a supermarket of Florianópolis, Santa Caratina, Brazil. The foods were classified according to the Brazilian food labeling legislation. Central tendency and variability values were calculated for the serving sizes and energy values reported on the labels, as well as the ratio between the reported and reference energy value. The Spearman correlation test was performed between the reference serving size and the reference energy density, and also between the reference serving size and energy density of each study food. RESULTS: Nutrition labeling and the Food Guide presented reference servings with different sizes and energy values. The serving sizes reported on the labels did not follow either of the references and presented heterogeneous values, with a maximum range of 55-240 g among ready and semi-ready pre-prepared dishes. The reported energy values were between 0.1 times smaller and 2.4 times larger than the reference values. The reference serving sizes presented a highly inverse correlation with the reference energy density (Spearman coefficient= 0.9 and a very low inverse correlation with the energy density of the foods analyzed (Spearman coefficient= 0.2. CONCLUSION: This study showed the need for standardizing reference serving size information for the Brazilian population as well as reviewing nutrition labeling legislation in order to standardize the serving sizes reported on labels and to update the reference energy density used to calculate serving sizes.

Medicinal aspects of opium as described in Avicenna's Canon of Medicine.

Science.gov (United States)

Heydari, Mojtaba; Hashempur, Mohammad Hashem; Zargaran, Arman

2013-01-01

Throughout history, opium has been used as a base for the opioid class of drugs used to suppress the central nervous system. Opium is a substance extracted from the opium poppy (Papaver somniferum L.). Its consumption and medicinal application date back to antiquity. In the medieval period, Avicenna, a famous Persian scholar (980-1037 AD) described poppy under the entry Afion of his medical encyclopedia Canon of Medicine. Various effects of opium consumption, both wanted and unwanted are discussed in the encyclopedia. The text mentions the effects of opioids such as analgesic, hypnotic, antitussive, gastrointestinal, cognitive, respiratory depression, neuromuscular disturbance, and sexual dysfunction. It also refers to its potential as a poison. Avicenna describes several methods of delivery and recommendations for doses of the drug. Most of opioid effects described by Avicenna have subsequently been confirmed by modern research, and other references to opium use in medieval texts call for further investigation. This article highlights an important aspect of the medieval history of medicine.

DEPOT database: Reference manual and user's guide

International Nuclear Information System (INIS)

Clancey, P.; Logg, C.

1991-03-01

DEPOT has been developed to provide tracking for the Stanford Linear Collider (SLC) control system equipment. For each piece of equipment entered into the database, complete location, service, maintenance, modification, certification, and radiation exposure histories can be maintained. To facilitate data entry accuracy, efficiency, and consistency, barcoding technology has been used extensively. DEPOT has been an important tool in improving the reliability of the microsystems controlling SLC. This document describes the components of the DEPOT database, the elements in the database records, and the use of the supporting programs for entering data, searching the database, and producing reports from the information

Microgrid cyber security reference architecture.

Energy Technology Data Exchange (ETDEWEB)

Veitch, Cynthia K.; Henry, Jordan M.; Richardson, Bryan T.; Hart, Derek H.

2013-07-01

This document describes a microgrid cyber security reference architecture. First, we present a high-level concept of operations for a microgrid, including operational modes, necessary power actors, and the communication protocols typically employed. We then describe our motivation for designing a secure microgrid; in particular, we provide general network and industrial control system (ICS)-speci c vulnerabilities, a threat model, information assurance compliance concerns, and design criteria for a microgrid control system network. Our design approach addresses these concerns by segmenting the microgrid control system network into enclaves, grouping enclaves into functional domains, and describing actor communication using data exchange attributes. We describe cyber actors that can help mitigate potential vulnerabilities, in addition to performance bene ts and vulnerability mitigation that may be realized using this reference architecture. To illustrate our design approach, we present a notional a microgrid control system network implementation, including types of communica- tion occurring on that network, example data exchange attributes for actors in the network, an example of how the network can be segmented to create enclaves and functional domains, and how cyber actors can be used to enforce network segmentation and provide the neces- sary level of security. Finally, we describe areas of focus for the further development of the reference architecture.

Probabilistic safety analysis procedures guide

International Nuclear Information System (INIS)

Papazoglou, I.A.; Bari, R.A.; Buslik, A.J.

1984-01-01

A procedures guide for the performance of probabilistic safety assessment has been prepared for interim use in the Nuclear Regulatory Commission programs. The probabilistic safety assessment studies performed are intended to produce probabilistic predictive models that can be used and extended by the utilities and by NRC to sharpen the focus of inquiries into a range of tissues affecting reactor safety. This guide addresses the determination of the probability (per year) of core damage resulting from accident initiators internal to the plant and from loss of offsite electric power. The scope includes analyses of problem-solving (cognitive) human errors, a determination of importance of the various core damage accident sequences, and an explicit treatment and display of uncertainties for the key accident sequences. Ultimately, the guide will be augmented to include the plant-specific analysis of in-plant processes (i.e., containment performance) and the risk associated with external accident initiators, as consensus is developed regarding suitable methodologies in these areas. This guide provides the structure of a probabilistic safety study to be performed, and indicates what products of the study are essential for regulatory decision making. Methodology is treated in the guide only to the extent necessary to indicate the range of methods which is acceptable; ample reference is given to alternative methodologies which may be utilized in the performance of the study

Interior Design 1992 Buyers Guide issue.

Science.gov (United States)

1992-01-30

The Interior Design Magazine Buyers Guide is compiled with you, the designer, in mind. So it's packed with the most comprehensive collection of sources available anyplace--arranged for fast, easy access. First, the Keyword Index presents all the Buyers Guide product categories alphabetically (see the first tab divider). Refer to the page number indicated in the Product Index (second tab divider) to view various manufacturers of products under each category heading. Addresses, phone and fax numbers, regional and international showroom/representatives are located in the A-Z Index (third tab divider) in alphabetical order. Consult the table of contents for trade associations, lighting consultants, marts, and other useful sections.

Self-benchmarking Guide for Cleanrooms: Metrics, Benchmarks, Actions

Energy Technology Data Exchange (ETDEWEB)

Mathew, Paul; Sartor, Dale; Tschudi, William

2009-07-13

This guide describes energy efficiency metrics and benchmarks that can be used to track the performance of and identify potential opportunities to reduce energy use in laboratory buildings. This guide is primarily intended for personnel who have responsibility for managing energy use in existing laboratory facilities - including facilities managers, energy managers, and their engineering consultants. Additionally, laboratory planners and designers may also use the metrics and benchmarks described in this guide for goal-setting in new construction or major renovation. This guide provides the following information: (1) A step-by-step outline of the benchmarking process. (2) A set of performance metrics for the whole building as well as individual systems. For each metric, the guide provides a definition, performance benchmarks, and potential actions that can be inferred from evaluating this metric. (3) A list and descriptions of the data required for computing the metrics. This guide is complemented by spreadsheet templates for data collection and for computing the benchmarking metrics. This guide builds on prior research supported by the national Laboratories for the 21st Century (Labs21) program, supported by the U.S. Department of Energy and the U.S. Environmental Protection Agency. Much of the benchmarking data are drawn from the Labs21 benchmarking database and technical guides. Additional benchmark data were obtained from engineering experts including laboratory designers and energy managers.

System administrator`s guide to CDPS. Version 1.0

Energy Technology Data Exchange (ETDEWEB)

Didier, B.T.; Portwood, M.H.

1994-05-01

The System Administrator`s Guide to CDPS is intended for those responsible for setting up and maintaining the hardware and software of a Common Mapping Standard (CMS) Date Production System (CDPS) installation. This guide assists the system administrator in performing typical administrative functions. It is not intended to replace the Ultrix Documentation Set that should be available for a DCPS installation. The Ultrix Documentation Set will be required to provide details on referenced Ultrix commands as well as procedures for performing Ultrix maintenance functions. There are six major sections in this guide. Section 1 introduces the system administrator to CDPS and describes the assumptions that are made by this guide. Section 2 describes the CDPS platform configuration. Section 3 describes the platform preparation that is required to install the CDPS software. Section 4 describes the CPS software and its installation procedures. Section 5 describes the CDS software and its installation procedures. Section 6 describes various operation and maintenance procedures. Four appendices are also provided. Appendix A contains a list of used acronyms. Appendix B provides a terse description of common Ultrix commands that are used in administrative functions. Appendix C provides sample CPS and CDS configuration files. Appendix D provides a required list and a recommended list of Ultrix software subsets for installation on a CDPS platform.

Establishment of Reference Doses for residues of allergenic foods: Report of the VITAL Expert Panel

NARCIS (Netherlands)

Taylor, S.L.; Baumert, J.L.; Kruizinga, A.G.; Remington, B.C.; Crevel, R.W.R.; Brooke-Taylor, S.; Allen, K.J.; Houben, G.

2014-01-01

In 2011, an expert panel was assembled to establish appropriate Reference Doses for allergenic food residues as a part of the VITAL (Voluntary Incidental Trace Allergen Labeling) program of The Allergen Bureau of Australia & New Zealand (ABA). These Reference Doses would guide advisory labeling

Guide to radioactive waste management literature

International Nuclear Information System (INIS)

Houser, B.L.; Holoway, C.F.; Madewell, D.G.

1977-10-01

Increased public concern about radioactive waste management has called attention to this aspect of the nuclear fuel cycle. Socio-economic planning and technical development are being undertaken to assure that such wastes will be managed safely. This Guide to Radioactive Waste Management Literature has been compiled to serve scientists, engineers, administrators, legislators, and private citizens by directing them to sources of information on various aspects of the subject. References were selected from about 6000 documents on waste management in the computerized information centers in Oak Ridge. The documents were selected, examined, indexed, and abstracted between 1966-1976 by several knowledgeable indexers, principally at the Nuclear Safety Information Center. The selected references were further indexed and classified into 12 categories. Each category is discussed in enough detail to give some understandng of present technology in various phases of waste management and some appreciation of the attendant issues and problems. The bibliographic part of this guide exists in computerized form in the Health Physics Information System and is available through the Oak Ridge Information Center Complex for searching from remote terminals

Guide to radioactive waste management literature

Energy Technology Data Exchange (ETDEWEB)

Houser, B.L.; Holoway, C.F.; Madewell, D.G.

1977-10-01

Increased public concern about radioactive waste management has called attention to this aspect of the nuclear fuel cycle. Socio-economic planning and technical development are being undertaken to assure that such wastes will be managed safely. This Guide to Radioactive Waste Management Literature has been compiled to serve scientists, engineers, administrators, legislators, and private citizens by directing them to sources of information on various aspects of the subject. References were selected from about 6000 documents on waste management in the computerized information centers in Oak Ridge. The documents were selected, examined, indexed, and abstracted between 1966-1976 by several knowledgeable indexers, principally at the Nuclear Safety Information Center. The selected references were further indexed and classified into 12 categories. Each category is discussed in enough detail to give some understandng of present technology in various phases of waste management and some appreciation of the attendant issues and problems. The bibliographic part of this guide exists in computerized form in the Health Physics Information System and is available through the Oak Ridge Information Center Complex for searching from remote terminals.

Methods for definition of reference conditions for a repository site taking long-term environmental change into account

Energy Technology Data Exchange (ETDEWEB)

Ikonen, A.T.K. [Environmental Research and Assessment EnviroCase, Ltd. (Finland)

2014-07-01

In a few countries, programmes for disposal of spent nuclear fuel have proceeded into a site-specific phase, and the number of low- and intermediate-level nuclear waste repositories requiring updated state-of-the-art long-term safety assessments is considerable. In this contribution, the approach employed in the Finnish spent fuel disposal programme is analysed and used as an example for a more general methodology for defining reference surface conditions for a site, e.g. to guide selection of representative input data to safety assessments, using spatio-temporal analogues so that long-term environmental changes are taken into account. The contribution incorporates also elements from discussions in the IAEA EMRAS II and MODARIA working groups on addressing the environmental change in the assessments. The legacy of the earlier BIOMASS project is also recognised. Broadly, the methods to be presented include identification of similarity factors (e.g. geological, biological and climate regimes) upon which a reference area can be delineated. Within the reference area, characteristic lines of development and biotopes are identified and described, and these are then used to guide further research and application of literature data to iteratively accumulate adequate understanding of the site conditions and relevant processes at the present and in the future (by projecting further the past and present development lines and biotopes). In this iterative approach, also the intensity of research efforts can be adjusted with the stage of the repository programme, as will be discussed in the complete contribution. Document available in abstract form only. (authors)

Bottom nozzle to guide tube connection

International Nuclear Information System (INIS)

Bryan, W.J.

1991-01-01

This patent describes a nuclear fuel assembly which includes an upper end fitting and a lower end fitting spaced therefrom and connected thereto by elongated guide tubes of one alloy having an open upper end and a closed lower end with spaced fuel element retaining grids mounted on the guide tubes therebetween, the closed lower ends of the guide tubes including a threaded central passageway and the attachment of the guide tubes to the lower end fitting of another alloy. It comprises: an externally threaded bolt with a first end threadably received in the threaded central passageway of the lower end of the guide tube and a head at the other end of the side of the lower end fitting opposite the guide tube; an interruption in the external threads of the bolt which forms a groove which communicates the interior of the guide tube with the side of the lower end fitting opposite the guide tube and enhances its frictional engagement with the threaded central passageway, thereby to hold and attach the guide tube and lower end fitting firmly together, even through a series of temperature cycles

COMPOZ data guide

International Nuclear Information System (INIS)

Knight, J.R.

1984-01-01

The COMPOZ Data Guide used to create the Standard Composition Library is described. Of particular importance is documentation of the COMPOZ input data file structure. Knowledge of the file structure allows users to edit the data file and subsequently create their own site-specific composition library

Experiments of Long-range Inspection Method in Straight Pipes using Ultrasonic Guided Waves

International Nuclear Information System (INIS)

Eom, H. S.; Lim, S. H.; Kim, J. H.; Joo, Y.S.

2006-02-01

This report describes experimental results of a long-range inspection method of pipes using ultrasonic guided waves. In chapter 2, theory of guided wave was reviewed. In chapter 3, equipment and procedures which were used in the experiments were described. Detailed specifications of the specimens described in chapter 4. In chapter 5, we analyzed characteristics of guided wave signals according to shapes and sizes of defects and presents results of various signal processing methods

Dwellings with cellars and basements. A BRE guide to radon remedial measures in existing dwellings

International Nuclear Information System (INIS)

Scivyer, C.R.; Jaggs, M.P.R.

1998-01-01

This guide is one of a series giving practical advice on methods of reducing radon levels in existing dwellings. It is intended to help surveyors, builders and householders who are trying to reduce indoor radon levels in houses with cellars or basements. The guide is based on a large body of remedial work carried out to advice given by BRE, and on discussions with others working in the field. The measures it describes are applicable, in principle, to all dwellings and other buildings of a similar scale and construction which have cellars or basements. Contact details of other organisations referred to are listed at the back of this guide. Basements and cellars are relatively uncommon in the United Kingdom, but where they do occur they are likely to be major contributors to the radon problem within a building. Experience shows that most houses with high indoor radon levels can be remedied through the use of straightforward building works. These can be carried out by a builder or householder competent in DIY. The cost should not be excessive. Before reading this guide, for background information on radon, consult Radon: a householder's guide and Radon: a guide to reducing levels M your home, obtainable from local Environmental Health Officers or from the Department of the Environment, Transport and the Regions. The Government recommends that, if the average radon concentration in a dwelling exceeds 200 Bq/m 3 (the 'action' level), measures should be taken to reduce it. This guide assumes that radon measurements have been made in the building and that the annual average indoor radon level was shown to exceed the action level

Apparel and Textiles Production, Management, and Services. Reference Book.

Science.gov (United States)

Texas Tech Univ., Lubbock. Home Economics Curriculum Center.

Developed with input from personnel in the industries, this reference book complements a matching curriculum guide for a course on the textiles and apparel industries. The book emphasizes job skills and the attitudes and interpersonal skills needed for successful employment in the textiles/apparel industry. Each of the 22 chapters of the book…

Ultrasound guided percutaneous removal of wooden foreign bodies in the extremities with hydro-dissection technique

Energy Technology Data Exchange (ETDEWEB)

Park, HeeJin; Lee, So Yeon; Chung, Eun Chul; Rho, Myung Ho [Dept. of Radiology, Sungkyunkwan University School of Medicine, Kangbuk Samsung Hospital, Seoul (Korea, Republic of); Lee, Sung Moon; Son, Eun Seok [Dongsan Medical Center, Keimyung University School of Medicine, Daegu (Korea, Republic of); Lee, Sun Joo [Dept. of Radiology, Inje University College of Medicine, Busan Paik Hospital, Busan (Korea, Republic of)

2015-12-15

We described the technique of ultrasound (US)-guided percutaneous removal of the foreign bodies (FB) with hydro-dissection in the radiologic department and presented video files of several cases.Four patients referred to the radiology department for US evaluation and US-guided percutaneous removal of the FBs in the upper and lower extremities between November, 2006 and November, 2013 were included in this study. The procedures started with US evaluation for the exact location and shape of the FB. A 5 mm-sized skin incision was made at the site of the nearest point from the FB where no passing arteries or tendons were present. We adopted a hydro dissection technique to separate the FB from adjacent tissue using a 2% lidocaine solution. Injected anesthetics detached the FBs from surrounding tissue and thereby facilitated removal. After the tip of the mosquito forceps reached the FB, the wooden FBs were removed. The mean time required for the entire procedure was approximately 20 minutes. There were no significant complications during the US-guided removal or long-term complications after the procedure. All 4 FBs were successfully removed from the soft tissue under US guidance. Ultrasound-guided percutaneous removal of the FBs with hydro-dissection in the radiology department is a less invasive and safe method over surgical removal in the operating room. Additionally, the use of a guide wire and serial dilator may help minimize soft tissue injury and facilitate the introduction of forceps.

A practical guide to SysML the systems modeling language

CERN Document Server

Friendenthal,Sanford; Steiner, Rick

2009-01-01

This book is the bestselling, authoritative guide to SysML for systems and software engineers, providing a comprehensive and practical resource for modeling systems with SysML. Fully updated to cover newly released version 1.3, it includes a full description of the modeling language along with a quick reference guide, and shows how an organization or project can transition to model-based systems engineering using SysML, with considerations for processes, methods, tools, and training. Numerous examples help readers understand how SysML can be used in practice, while reference material facilitates studying for the OMG Systems Modeling Professional (OCSMP) Certification Program, designed to test candidates' knowledge of SysML and their ability to use models to represent real-world systems.

Computed tomography-guided core-needle biopsy of lung lesions: an oncology center experience

Energy Technology Data Exchange (ETDEWEB)

Guimaraes, Marcos Duarte; Fonte, Alexandre Calabria da; Chojniak, Rubens, E-mail: marcosduarte@yahoo.com.b [Hospital A.C. Camargo, Sao Paulo, SP (Brazil). Dept. of Radiology and Imaging Diagnosis; Andrade, Marcony Queiroz de [Hospital Alianca, Salvador, BA (Brazil); Gross, Jefferson Luiz [Hospital A.C. Camargo, Sao Paulo, SP (Brazil). Dept. of Chest Surgery

2011-03-15

Objective: The present study is aimed at describing the experience of an oncology center with computed tomography guided core-needle biopsy of pulmonary lesions. Materials and Methods: Retrospective analysis of 97 computed tomography-guided core-needle biopsy of pulmonary lesions performed in the period between 1996 and 2004 in a Brazilian reference oncology center (Hospital do Cancer - A.C. Camargo). Information regarding material appropriateness and the specific diagnoses were collected and analyzed. Results: Among 97 lung biopsies, 94 (96.9%) supplied appropriate specimens for histological analyses, with 71 (73.2%) cases being diagnosed as malignant lesions and 23 (23.7%) diagnosed as benign lesions. Specimens were inappropriate for analysis in three cases. The frequency of specific diagnosis was 83 (85.6%) cases, with high rates for both malignant lesions with 63 (88.7%) cases and benign lesions with 20 (86.7%). As regards complications, a total of 12 cases were observed as follows: 7 (7.2%) cases of hematoma, 3 (3.1%) cases of pneumothorax and 2 (2.1%) cases of hemoptysis. Conclusion: Computed tomography-guided core needle biopsy of lung lesions demonstrated high rates of material appropriateness and diagnostic specificity, and low rates of complications in the present study. (author)

MBN Explorer Users' Guide

DEFF Research Database (Denmark)

Solov'yov, Ilia A.; Sushko, Gennady; Solov'yov, Andrey V.

The MBN Explorer Users' Guide describes how to install and to run MBN Explorer, the software package for advanced multiscale simulations of complex molecular structure and dynamics. This guide includes the description of the main features and the algorithms of the program, the manual how to use...... simulations of structure and dynamics of a broad range of systems with the sizes from the atomic up to the mesoscopic scales. MBN Explorer is being developed and distributed by MBN Research Center, www.mbnresearch.com, which organises hands-on tutorials for the software, user's workshops and conferences....

Contextual analysis of human non-verbal guide behaviors to inform the development of FROG, the Fun Robotic Outdoor Guide

NARCIS (Netherlands)

Karreman, Daphne Eleonora; van Dijk, Elisabeth M.A.G.; Evers, Vanessa

2012-01-01

This paper reports the first step in a series of studies to design the interaction behaviors of an outdoor robotic guide. We describe and report the use case development carried out to identify effective human tour guide behaviors. In this paper we focus on non-verbal communication cues in gaze,

75 FR 9002 - Draft Regulatory Guide: Issuance, Availability

Science.gov (United States)

2010-02-26

... Guide, DG-3040, ``Design, Construction, and Inspection of Embankment Retention Systems at Fuel Cycle... October 1973. This guide describes some engineering practices and methods generally considered by the NRC to be satisfactory for the design, construction, and inspection of embankment retention systems used...

Curved-straight neutron guide system with uniform spatial intensity distribution

International Nuclear Information System (INIS)

Mildner, D.F.R.; Cook, J.C.

2008-01-01

The spatial intensity distribution of neutrons emerging from a curved guide is asymmetric, and straight guide sections are sometimes appended to curved guides to make the intensity distribution more nearly uniform. For idealized uniform illumination and in the perfect reflectivity approximation, the spatial-angular acceptance at the exit of the combination can be made exactly uniform for a range of long wavelengths by using a sufficiently long straight section, together with a curved guide whose outer wall coating has a critical angle slightly greater than those of the other guide walls. We refer to this as a 'phase space tailoring guide' where the coatings on the inner wall and straight section are used to define the required divergence at the end of the guide. Increasing the critical angle of the outer wall of the curved section reduces the characteristic wavelength of the curved guide as well as the wavelength at which ideal uniformity can be obtained. The outer wall coating need only be of sufficiently high critical angle to fill the transmittable phase space area of the straight guide uniformly to adequately short wavelength

The linear algebra survival guide illustrated with Mathematica

CERN Document Server

Szabo, Fred

2015-01-01

The Linear Algebra Survival Guide is a reference book with a free downloadable Mathematica notebook containing all of interactive code to make the content of the book playable in Mathematica and the Mathematica Player. It offers a concise introduction to the core topics of linear algebra which includes numerous exercises that will accompany a first or second course in linear algebra. This book will guide you through the powerful graphic displays and visualization of Mathematica that make the most abstract theories seem simple-- allowing you to tackle realistic problems using simple mathematic

Xcode 5 developer reference

CERN Document Server

Wentk, Richard

2014-01-01

Design, code, and build amazing apps with Xcode 5 Thanks to Apple's awesome Xcode development environment, you can create the next big app for Macs, iPhones, iPads, or iPod touches. Xcode 5 contains gigabytes of great stuff to help you develop for both OS X and iOS devices - things like sample code, utilities, companion applications, documentation, and more. And with Xcode 5 Developer Reference, you now have the ultimate step-by-step guide to it all. Immerse yourself in the heady and lucrative world of Apple app development, see how to tame the latest features and functions, and find loads of

Transportation management center data capture for performance and mobility measures reference manual.

Science.gov (United States)

2013-03-01

The Guide to Transportation Management Center (TMC) Data Capture for Performance and Mobility Measures is a two-volume document consisting of a summary Guidebook and this Reference Manual. These documents provide technical guidance and recommended pr...

77 FR 36017 - Regulatory Guide 7.3, Procedures for Picking Up and Receiving Packages of Radioactive Material

Science.gov (United States)

2012-06-15

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0139] Regulatory Guide 7.3, Procedures for Picking Up and... Guide (RG) 7.3, ``Procedures for Picking Up and Receiving Packages of Radioactive Material.'' The guide..., please contact the NRC's Public Document Room (PDR) reference staff at 1-800-397-4209, or 301-415-4737...

Probabilistic safety analysis procedures guide. Sections 1-7 and appendices. Volume 1, Revision 1

International Nuclear Information System (INIS)

Bari, R.A.; Buslik, A.J.; Cho, N.Z.

1985-08-01

A procedures guide for the performance of probabilistic safety assessment has been prepared for interim use in the Nuclear Regulatory Commission programs. It will be revised as comments are received, and as experience is gained from its use. The probabilistic safety assessment studies performed are intended to produce probabilistic predictive models that can be used and extended by the utilities and by NRC to sharpen the focus of inquiries into a range of issues affecting reactor safety. This first volume of the guide describes the determination of the probability (per year) of core damage resulting from accident initiators internal to the plant (i.e., intrinsic to plant operation) and from loss of off-site electric power. The scope includes human reliability analysis, a determination of the importance of various core damage accident sequences, and an explicit treatment and display of uncertainties for key accident sequences. The second volume deals with the treatment of the so-called external events including seismic disturbances, fires, floods, etc. Ultimately, the guide will be augmented to include the plant-specific analysis of in-plant processes (i.e., containment performance). This guide provides the structure of a probabilistic safety study to be performed, and indicates what products of the study are valuable for regulatory decision making. For internal events, methodology is treated in the guide only to the extent necessary to indicate the range of methods which is acceptable; ample reference is given to alternative methodologies which may be utilized in the performance of the study. For external events, more explicit guidance is given

Preparation of plant-specific NDA reference material

International Nuclear Information System (INIS)

Abedin-Zadeh, R.; Beetle, T.; Kuhn, E.; Terrey, D.; Turel, S.; Busca, G.; Guardini, S.

1983-01-01

The importance of having suitable and well characterized non-destructive assay (NDA) reference materials for the verification activities of the safeguards control authorities is stressed. The Euratom Inspectorate and the IAEA have initiated an extensive programme for the procurement and preparation of Joint Euratom/IAEA safeguards NDA reference materials with the active participation of the Ispra Establishment of the Euratom Joint Research Centre. The different type and nature of materials, condition of measurements, and plant characteristics and provisions had to be taken into account for plant-specific NDA reference materials. The preparation of each reference material was planned case by case and specific criteria such as limitations in different facilities, measurement capabilities, conditions, product availability and population variability are being ascertained. A procurement scheme was prepared describing step-by-step procedures detailing responsibilities, measurement conditions, destructive analysis schemes, desired characteristics and methods of data evaluation. This paper describes the principles and procedures carried out for the preparation of a reference MOX pin, low enriched uranium reference rods, low enriched uranium reference drums, reference MTR assemblies, and THTR reference pebbles. The scheme for each characterization technique is presented. (author)

Presto 2.9 user's guide.

Energy Technology Data Exchange (ETDEWEB)

Jung, Joseph

2008-05-01

Presto is a Lagrangian, three-dimensional explicit, transient dynamics code that is used to analyze solids subjected to large, suddenly applied loads. The code is designed for a parallel computing environment and for problems with large deformations, nonlinear material behavior, and contact. Presto also has a versatile element library that incorporates both continuum elements and structural elements. This user's guide describes the input for Presto that gives users access to all the current functionality in the code. The environment in which Presto is built allows it to be coupled with other engineering analysis codes. Using a concept called scope, the input structure reflects the fact that Presto can be used in a coupled environment. The user's guide describes how scope is implemented from the outermost to the innermost scopes. Within a given scope, the descriptions of input commands are grouped based on functionality of the code. For example, all material input command lines are described in a chapter of the user's guide for all the material models that can be used in Presto.

Presto 4.18 user's guide.

Energy Technology Data Exchange (ETDEWEB)

Spencer, Benjamin Whiting

2010-09-01

Presto is a Lagrangian, three-dimensional explicit, transient dynamics code that is used to analyze solids subjected to large, suddenly applied loads. The code is designed for a parallel computing environment and for problems with large deformations, nonlinear material behavior, and contact. Presto also has a versatile element library that incorporates both continuum elements and structural elements. This user's guide describes the input for Presto that gives users access to all the current functionality in the code. The environment in which Presto is built allows it to be coupled with other engineering analysis codes. Using a concept called scope, the input structure reflects the fact that Presto can be used in a coupled environment. The user's guide describes how scope is implemented from the outermost to the innermost scopes. Within a given scope, the descriptions of input commands are grouped based on functionality of the code. For example, all material input command lines are described in a chapter of the user's guide for all the material models that can be used in Presto.

Eliminating line of sight in elliptic guides using gravitational curving

International Nuclear Information System (INIS)

Kleno, Kaspar H.; Willendrup, Peter K.; Knudsen, Erik; Lefmann, Kim

2011-01-01

Eliminating fast neutrons (λ<0.5A) by removing direct line of sight between the source and the target sample is a well established technique. This can be done with little loss of transmission for a straight neutron guide by horizontal curving. With an elliptic guide shape, however, curving the guide would result in a breakdown of the geometrical focusing mechanism inherent to the elliptical shape, resulting in unwanted reflections and loss of transmission. We present a new and yet untried idea by curving a guide in such a way as to follow the ballistic curve of a neutron in the gravitational field, while still retaining the elliptic shape seen from the accelerated reference frame of the neutron. Analytical calculations and ray-tracing simulations show that this method is useful for cold neutrons at guide lengths in excess of 100 m. We will present some of the latest results for guide optimization relevant for instrument design at the ESS, in particular an off-backscattering spectrometer which utilizes the gravitational curving, for 6.66 A neutrons over a guide length of 300 m.

NBS activities in biological reference materials

Energy Technology Data Exchange (ETDEWEB)

Rasberry, S.D.

1988-12-01

NBS activities in biological reference materials during 1986-1988 are described with a preview of plans for future certifications of reference materials. During the period, work has been completed or partially completed on about 40 reference materials of importance to health, nutrition, and environmental quality. Some of the reference materials that have been completed during the period and are described include: creatinine (SRM 914a), bovine serum albumin (SRM 927a), cholesterol in human serum (SRM's 1951-1952), aspartate aminotransferase (RM 8430), cholesterol and fat-soluble vitamins in coconut oil (SRM 1563), wheat flour (SRM 1567a), rice flour (SRM 1568a), mixed diet (RM 8431a), dinitropyrene isomers and 1-nitropyrene (SRM 1596), and complex PAH's from coal tar (SRM 1597). Oyster tissue (SRM 1566a) is being analyzed and should be available in 1988.

Industrial wastes guide for Alsace; Guide des dechets de l`entreprise Alsace

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-01-01

This guide is aimed for industrial plant managers and gives comprehensive information on industrial waste management: effects of wastes on the environment (water, air, soil), waste processing limitations in Alsace, new regulations, taxes and incentives concerning waste processing in France, and references of national and regional (Alsace) administration and industrial agencies that are related with pollution abatement and control and waste management. The different types of wastes are reviewed, from papers to toxic solvents, with information given on volumes, processes, operators, processing equipment and equipment distributors

Evaluating Remote Reference Service: A Practical Guide to Problems and Solutions

Science.gov (United States)

Pomerantz, Jeffrey; Mon, Lorri; McClure, Charles R.

2008-01-01

This paper identifies key methodological issues affecting quality of data in the evaluation of remote reference services. Despite a growing number of studies in this area, no comprehensive effort has been made to identify potential problems and suggest solutions. The strategies proposed in this paper offer practical ways in which libraries can…

Entrance Counseling Guide for Direct Loan Borrowers

Science.gov (United States)

Federal Student Aid, US Department of Education, 2010

2010-01-01

This guide describes the four types of loans offered by the Direct Loan Program[SM]: (1) Direct Subsidized Loans; (2) Direct Unsubsidized Loans; (3) Direct PLUS Loans; and (4) Direct Consolidation Loans. Among the topics covered in the guide are: Use of Your Loan Money, The Master Promissory Note, How Your Loans Will Be Disbursed (Paid Out),…

Guide to Closing and Conditioning Ventilated Crawlspaces

Energy Technology Data Exchange (ETDEWEB)

Dickson, Bruce [IBACOS, Inc., Pittsburgh, PA (United States)

2013-01-01

This how-to guide explains the issues and concerns with conventional ventilated crawlspaces and provides prescriptive measures for improvements that will create healthier and more durable spaces. The methods described in this guide are not the only acceptable ways to treat a crawlspace but represent a proven strategy that works in many areas of the United States. The designs discussed in this guide may or may not meet the local building codes and as such will need to be researched before beginning the project.

Self-benchmarking Guide for Laboratory Buildings: Metrics, Benchmarks, Actions

Energy Technology Data Exchange (ETDEWEB)

Mathew, Paul; Greenberg, Steve; Sartor, Dale

2009-07-13

This guide describes energy efficiency metrics and benchmarks that can be used to track the performance of and identify potential opportunities to reduce energy use in laboratory buildings. This guide is primarily intended for personnel who have responsibility for managing energy use in existing laboratory facilities - including facilities managers, energy managers, and their engineering consultants. Additionally, laboratory planners and designers may also use the metrics and benchmarks described in this guide for goal-setting in new construction or major renovation. This guide provides the following information: (1) A step-by-step outline of the benchmarking process. (2) A set of performance metrics for the whole building as well as individual systems. For each metric, the guide provides a definition, performance benchmarks, and potential actions that can be inferred from evaluating this metric. (3) A list and descriptions of the data required for computing the metrics. This guide is complemented by spreadsheet templates for data collection and for computing the benchmarking metrics. This guide builds on prior research supported by the national Laboratories for the 21st Century (Labs21) program, supported by the U.S. Department of Energy and the U.S. Environmental Protection Agency. Much of the benchmarking data are drawn from the Labs21 benchmarking database and technical guides. Additional benchmark data were obtained from engineering experts including laboratory designers and energy managers.

Programmer's guide for the CC3 computer models of the concept for disposal of Canada's nuclear fuel waste

International Nuclear Information System (INIS)

Dougan, K.D.

1996-11-01

Atomic Energy of Canada Limited (AECL) is assessing a concept for disposing of CANDU reactor fuel waste in a vault deep in plutonic rock of the Canadian Shield. A computer program called the Systems Variability Analysis Code (SYVAC) was developed as an analytical tool for the postclosure (long-term) assessment of the concept, and for environmental assessments of other systems. SYVAC3, the third generation of the code, is an executive program that directs repeated simulation of the disposal system, which is described by the CC3 (Canadian Concept, generation 3) model. The CC3 model is comprised of the disposal vault submodel, the local geosphere submodel and the biosphere submodel. The CC3 Proarammer's Guide describes the programming philosophy and programming conventions not covered in the project standards. The guide includes a description of the overall logic for the CC3 vault, geosphere, and biosphere submodels. Each of the CC3 submodels is also isolated from the other two submbdels to create autonomous or 'stand-alone' submodels. The techniques used to isolate a CC3 submodel, and in particular to determine the submodells input and output data interface, are described. Structure charts are provided for the CC3 model and stand-alone submodels. This guide is meant as a companion document to the CC3 User's Manual. This guide does not describe how to use the CC3 software. The user should consult the CC3 User's Manual to determine how to configure, compile, link, and run the CC3 source code, as well as how to modify the data in the input files. It is intended that the CC3 code version CC305 be executed with SYVAC3 version SV309 and the Modelling Algorithm Library (ML3) version ML303, both developed for the assessment of the concept. SYVAC3-CC3-ML3 (also referred to as 'SC3') can be run on any platform containing an ANSI FORTRAN 77 compliant compiler. Recommended hardware environments are specified in the CC3 User's Manual. (author)

77 FR 8902 - Draft Regulatory Guide: Issuance, Availability Decommissioning of Nuclear Power Reactors

Science.gov (United States)

2012-02-15

... Decommissioning of Nuclear Power Reactors AGENCY: Nuclear Regulatory Commission. ACTION: Draft regulatory guide... draft regulatory guide (DG) DG-1271 ``Decommissioning of Nuclear Power Reactors.'' This guide describes... Regulatory Guide 1.184, ``Decommissioning of Nuclear Power Reactors,'' dated July 2000. This proposed...

Closed reduction with CT-guided screw fixation for unstable sacroiliac joint fracture-dislocation

Energy Technology Data Exchange (ETDEWEB)

Baskin, Kevin M.; Cahill, Ann Marie; Kaye, Robin D. [Children' s Hospital of Philadelphia, Department of Radiology, Philadelphia, PA (United States); Born, Christopher T. [Temple University Hospital/Temple Children' s Hospital, Temple Sports Medicine, Marlton, NJ (United States); Grudziak, Jan S. [Children' s Hospital of Pittsburgh, Department of Orthopedic Surgery, Pittsburgh, PA (United States); Towbin, Richard B.

2004-12-01

Unstable posterior pelvic ring fractures and dislocations are uncommon but potentially life-threatening injuries in children. Early definitive management reduces risk of immediate complications as well as chronic pain and gait dysfunction. Conventional operative therapy carries substantial risk of extensive blood loss and iatrogenic neurological and vascular injury. Minimally invasive image-guided intervention may further reduce immediate risk and improve long-term outcome. To describe CT-guided closed reduction and internal fixation (CRIF) and review outcomes of unstable fracture-dislocation of the sacroiliac (SI) joint in children. Between 2000 and 2003, three children (two girls, one boy) age 8-14 years were referred to interventional radiology for treatment of unstable SI joint fracture-dislocation not adequately treated with anterior external fixation alone. The three affected SI joints (two left, one right) were treated in a combined approach by pediatric interventional radiologists and orthopedic surgeons, using a percutaneous approach under CT guidance. Over a threaded guiding pin, 7.3 mm cannulated screws were used to achieve stable reduction of the affected SI joints. One screw was removed after slight (2 mm) migration. No neurovascular or other complications occurred. All patients had satisfactory healing with near-anatomic reduction, although recovery of the youngest was delayed by associated spinal injury. Compared to open surgical alternatives, CRIF under CT guidance reduces operating time, decreases blood loss, and allows early definitive fixation and immediate non-weight-bearing mobilization with a low rate of complication for unstable posterior pelvic ring fractures. In addition, CT-guided placement of the guide pin may allow safer screw positioning and may minimize the total number of screws needed to achieve pelvic stability. (orig.)

Closed reduction with CT-guided screw fixation for unstable sacroiliac joint fracture-dislocation

International Nuclear Information System (INIS)

Baskin, Kevin M.; Cahill, Ann Marie; Kaye, Robin D.; Born, Christopher T.; Grudziak, Jan S.; Towbin, Richard B.

2004-01-01

Unstable posterior pelvic ring fractures and dislocations are uncommon but potentially life-threatening injuries in children. Early definitive management reduces risk of immediate complications as well as chronic pain and gait dysfunction. Conventional operative therapy carries substantial risk of extensive blood loss and iatrogenic neurological and vascular injury. Minimally invasive image-guided intervention may further reduce immediate risk and improve long-term outcome. To describe CT-guided closed reduction and internal fixation (CRIF) and review outcomes of unstable fracture-dislocation of the sacroiliac (SI) joint in children. Between 2000 and 2003, three children (two girls, one boy) age 8-14 years were referred to interventional radiology for treatment of unstable SI joint fracture-dislocation not adequately treated with anterior external fixation alone. The three affected SI joints (two left, one right) were treated in a combined approach by pediatric interventional radiologists and orthopedic surgeons, using a percutaneous approach under CT guidance. Over a threaded guiding pin, 7.3 mm cannulated screws were used to achieve stable reduction of the affected SI joints. One screw was removed after slight (2 mm) migration. No neurovascular or other complications occurred. All patients had satisfactory healing with near-anatomic reduction, although recovery of the youngest was delayed by associated spinal injury. Compared to open surgical alternatives, CRIF under CT guidance reduces operating time, decreases blood loss, and allows early definitive fixation and immediate non-weight-bearing mobilization with a low rate of complication for unstable posterior pelvic ring fractures. In addition, CT-guided placement of the guide pin may allow safer screw positioning and may minimize the total number of screws needed to achieve pelvic stability. (orig.)

Standard guide for digital detector array radiology

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This standard is a user guide, which is intended to serve as a tutorial for selection and use of various digital detector array systems nominally composed of the detector array and an imaging system to perform digital radiography. This guide also serves as an in-detail reference for the following standards: Practices E2597, , and E2737. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

The Definitive Guide to CentOS

CERN Document Server

Membrey, P; Angenendt, R

2009-01-01

CentOS is just like Red Hat, but without the price tag and with the virtuous license. When belts have to be tightened, we want to read about an OS with all the features of a commercial Linux variety, but without the pain. The Definitive Guide to CentOS is the first definitive reference for CentOS and focuses on CentOS alone, the workhorse Linux distro, that does the heavy lifting in small and medium-size enterprises without drawing too much attention to itself. *Provides tutorial and hands-on learning but is also designed to be used as a reference*Bases all examples on real-world tasks that re

Latin Curriculum Guide.

Science.gov (United States)

North Carolina State Dept. of Public Instruction, Raleigh. Instructional Services.

North Carolina's Latin curriculum guide describes the overarching concepts for Latin study, particularly at the secondary level, and outlines what students should know and be able to do at the beginning, intermediate, and advanced levels. It is designed to provide directions to school districts as they plan and/or continue to improve their Latin…

Python library reference

NARCIS (Netherlands)

G. van Rossum (Guido)

1995-01-01

textabstractPython is an extensible, interpreted, object-oriented programming language. It supports a wide range of applications, from simple text processing scripts to interactive WWW browsers. While the Python Reference Manual describes the exact syntax and semantics of the language, it does not

Pain and anxiety control: an online study guide.

Science.gov (United States)

2008-05-01

The Editorial Board of the Journal of Endodontics has developed a literature-based study guide of topical areas related to endodontics. This study guide is intended to give the reader a focused review of the essential endodontic literature and does not cite all possible articles related to each topic. Although citing all articles would be comprehensive, it would defeat the idea of a study guide. This section will cover pain theories and dentin hypersensitivity, referred pain, oral pain not of dental origin, barodontalgia, local anesthetics, long-acting local anesthetics, intrapulpal anesthesia, intraligamentary anesthesia, intraosseous anesthesia, inferior alveolar nerve block anesthesia, Gow-Gates anesthesia technique, Vazirani-Akinosi anesthesia technique, second-division block anesthesia technique, endodontic postoperative pain, effect of occlusal adjustment on endodontic pain, paresthesia associated with periradicular pathosis, analgesics, sedation, and endodontic flare-ups.

ASN guide project: complete cleaning-up modalities acceptable in nuclear base installations in France - ASN guide project nr 14 - Release of 21/06/2010

International Nuclear Information System (INIS)

2010-01-01

As any nuclear base installation evolves during its exploitation, some premises or buildings may change of use or be destroyed. In the first case, a complete cleaning up might be necessary to get rid of radioactive products. In order to deal with this issue, after a brief recall of the regulatory context and references, and a recall of the general doctrine of waste management in nuclear base installations in France, this guide project presents the principles for a complete cleaning up of structures belonging to an area containing nuclear wastes. It describes the modalities of definition of three different and successive defence lines. It defines the requirements in performing cleaning-up operations, the requirements in terms of quality insurance, and the different administrative procedures (before, during and after cleaning-up works). Some particular cases are addressed

Otitis Media with Effusion in Young Children. Clinical Practice Guideline, Quick Reference Guide for Clinicians, [and] Parent Guide, Consumer Version, Number 12.

Science.gov (United States)

Agency for Health Care Policy and Research (DHHS/PHS), Rockville, MD.

Otitis media with effusion and its related hearing loss have been associated with delayed language development, particularly if the disease is recurrent or of long duration, although available data are insufficient to establish a causal linkage. This guide presents recommendations based on extensive reviews of the relevant medical and…

Nuclear criticality safety guide

International Nuclear Information System (INIS)

Ro, Seong Ki; Shin, Hee Seong; Park, Seong Won; Shin, Young Joon.

1997-06-01

Nuclear criticality safety guide was described for handling, transportation and storage of nuclear fissile materials in this report. The major part of the report was excerpted frp, TID-7016(revision 2) and nuclear criticality safety written by Knief. (author). 16 tabs., 44 figs., 5 refs

Virtual Reference, Real Money: Modeling Costs in Virtual Reference Services

Science.gov (United States)

Eakin, Lori; Pomerantz, Jeffrey

2009-01-01

Libraries nationwide are in yet another phase of belt tightening. Without an understanding of the economic factors that influence library operations, however, controlling costs and performing cost-benefit analyses on services is difficult. This paper describes a project to develop a cost model for collaborative virtual reference services. This…

Advanced American Idioms: A Guide to Everyday Usage.

Science.gov (United States)

Allan, Edward Jay

A guide to several hundred common American idioms and slang phrases such as "to get something straight,""to mooch," and "in the bag" provides definitions, examples of usage, variations, and explanations when appropriate. A list of common abbreviations, such as "ASAP," and their referents is also included. (MSE)

Guide for External Beam Radiotherapy. Procedures 2007

International Nuclear Information System (INIS)

Ardiet, Jean-Michel; Bourhis, Jean; Eschwege, Francois; Gerard, Jean-Pierre; Martin, Philippe; Mazeron, Jean-Jacques; Barillot, Isabelle; Bey, Pierre; Cosset, Jean-Marc; Thomas, Olivier; Bolla, Michel; Bourguignon, Michel; Godet, Jean-Luc; Krembel, David; Valero, Marc; Bara, Christine; Beauvais-March, Helene; Derreumaux, Sylvie; Vidal, Jean-Pierre; Drouard, Jean; Sarrazin, Thierry; Lindecker-Cournil, Valerie; Robin, Sun Hee Lee; Thevenet, Nicolas; Depenweiller, Christian; Le Tallec, Philippe; Ortholan, Cecile; Aimone, Nicole; Baldeschi, Carine; Cantelli, Andree; Estivalet, Stephane; Le Prince, Cyrille; QUERO, Laurent; Costa, Andre; Gerard, Jean-Pierre; Ardiet, Jean-Michel; Bensadoun, Rene-Jean; Bourhis, Jean; Calais, Gilles; Lartigau, Eric; Ginot, Aurelie; Girard, Nicolas; Mornex, Francoise; Bolla, Michel; Chauvet, Bruno; Maingon, Philippe; Martin, Etienne; Azria, David; Gerard, Jean-Pierre; Grehange, Gilles; Hennequin, Christophe; Peiffert, Didier; Toledano, Alain; Belkacemi, Yazid; Courdi, Adel; Belliere, Aurelie; Peignaux, Karine; Mahe, Marc; Bondiau, Pierre-Yves; Kantor, Guy; Lepechoux, Cecile; Carrie, Christian; Claude, Line

2007-01-01

In order to optimize quality and security in the delivery of radiation treatment, the French SFRO (Societe francaise de radiotherapie oncologique) is publishing a Guide for Radiotherapy. This guide is realized according to the HAS (Haute Autorite de sante) methodology of 'structured experts consensus'. This document is made of two parts: a general description of external beam radiation therapy and chapters describing the technical procedures of the main tumors to be irradiated (24). For each procedure, a special attention is given to dose constraints in the organs at risk. This guide will be regularly updated

Guide to mathematical tables supplement no 1

CERN Document Server

Burunova, N M; Fedorova, R M

1960-01-01

A Guide to Mathematical Tables is a supplement to the Guide to Mathematical Tables published by the U.S.S.R. Academy of Sciences in 1956. The tables contain information on subjects such as powers, rational and algebraic functions, and trigonometric functions, as well as logarithms and polynomials and Legendre functions. An index listing all functions included in both the Guide and the Supplement is included.Comprised of 15 chapters, this supplement first describes mathematical tables in the following order: the accuracy of the table (that is, the number of decimal places or significant

Basic Gasoline Engine Mechanics. Florida Vocational Program Guide.

Science.gov (United States)

University of South Florida, Tampa. Dept. of Adult and Vocational Education.

This packet contains a program guide and Career Merit Achievement Plan (Career MAP) for the implementation of a basic gasoline engine mechanics program in Florida secondary and postsecondary schools. The program guide describes the program content and structure, provides a program description, lists job titles under the program, and includes a…

Ultrasound-guided genitourinary interventions: principles and techniques

Directory of Open Access Journals (Sweden)

Byung Kwan Park

2017-10-01

Full Text Available Ultrasound (US is often used to guide various interventional procedures in the genitourinary (GU tract because it can provide real-time imaging without any radiation hazard. Moreover, US can clearly visualize the pathway of an aspiration or biopsy needle to ensure the safety of the intervention. US guidance also helps clinicians to access lesions via the transabdominal, transhepatic, transvaginal, transrectal, and transperineal routes. Hence, US-guided procedures are useful for radiologists who wish to perform GU interventions. However, US-guided procedures and interventions are difficult for beginners because they involve a steep initial learning curve. The purpose of this review is to describe the basic principles and techniques of US-guided GU interventions.

Ultrasound-guided genitourinary interventions: principles and techniques

Energy Technology Data Exchange (ETDEWEB)

Park, Byung Kwan [Dept. of Radiology, Samsung Medical Center, Sungkyunkwan University School of Medicine, Seoul (Korea, Republic of)

2017-10-15

Ultrasound (US) is often used to guide various interventional procedures in the genitourinary (GU) tract because it can provide real-time imaging without any radiation hazard. Moreover, US can clearly visualize the pathway of an aspiration or biopsy needle to ensure the safety of the intervention. US guidance also helps clinicians to access lesions via the transabdominal, transhepatic, transvaginal, transrectal, and transperineal routes. Hence, US-guided procedures are useful for radiologists who wish to perform GU interventions. However, US-guided procedures and interventions are difficult for beginners because they involve a steep initial learning curve. The purpose of this review is to describe the basic principles and techniques of US-guided GU interventions.

National Center for Electron Microscopy users' guide

International Nuclear Information System (INIS)

1987-01-01

The National Center for Electron Microscopy (NCEM) in the Materials and Molecular Research Division of the Lawrence Berkeley Laboratory is a high voltage electron microscope facility for ultra-high resolution or dynamic in-situ studies. This guide describes the instruments and their specifications, support instrumentation, and user policies. Advice as to travel and accommodations is provided in the guide. (FI)

Openlayers 3 beginner's guide

CERN Document Server

Gratier, Thomas; Hazzard, Erik

2015-01-01

Whether you are a hobbyist or a professional web developer, if you wish to use maps on your website, then this book is for you. A basic understanding of JavaScript will be helpful, but is not necessary. If you've never worked with maps before, this book will introduce you to some common mapping topics and will guide you through the OpenLayers library. Experienced developers can also use this book as a reference to OpenLayers 3 components and to further enhance their knowledge.

Guide to treatment technology for contaminated soils

International Nuclear Information System (INIS)

Tran, H.; Aylward, R.

1992-01-01

This document is a guide for the screening of alternative treatment technologies for contaminated soils. The contents of this guide are organized into: 1. Introduction, II. Utilizing the table, III. Tables: Contamination Versus Technology, TV. Contaminant Waste Groups, and V. References. The four Contaminations Versus Technology tables are designed to identify the effectiveness and/or potential applicability of technologies to some or all compounds within specific waste groups. The tables also present limitations and special use considerations for the particular treatment technology. The phase of development of the technology is also included in the table. The phases are: Available, Innovative, and Emerging technologies. The technologies presented in this guide are organized according to the method of treatment. The four (4) treatment methods are Biological, Solidification/Stabilization, Thermal, and Chemical/Physical Treatment. There are several processing methods; some are well developed and proven, and others are in the development stage

Guided color consistency optimization for image mosaicking

Science.gov (United States)

Xie, Renping; Xia, Menghan; Yao, Jian; Li, Li

2018-01-01

This paper studies the problem of color consistency correction for sequential images with diverse color characteristics. Existing algorithms try to adjust all images to minimize color differences among images under a unified energy framework, however, the results are prone to presenting a consistent but unnatural appearance when the color difference between images is large and diverse. In our approach, this problem is addressed effectively by providing a guided initial solution for the global consistency optimization, which avoids converging to a meaningless integrated solution. First of all, to obtain the reliable intensity correspondences in overlapping regions between image pairs, we creatively propose the histogram extreme point matching algorithm which is robust to image geometrical misalignment to some extents. In the absence of the extra reference information, the guided initial solution is learned from the major tone of the original images by searching some image subset as the reference, whose color characteristics will be transferred to the others via the paths of graph analysis. Thus, the final results via global adjustment will take on a consistent color similar to the appearance of the reference image subset. Several groups of convincing experiments on both the synthetic dataset and the challenging real ones sufficiently demonstrate that the proposed approach can achieve as good or even better results compared with the state-of-the-art approaches.

Guide for the realization of Design Base Documents (DBD)

International Nuclear Information System (INIS)

Roca Mallofre, G. la

2010-01-01

Guide for improving the consistency and quality content of the Design Base Documents. It's a short description of how to carry out and complete these Documents but focusing on those aspects that can be more confusing and harder to interpret. This guide aims to clarify the term Design Base distinguishing between production and safety, and it focuses on safety Design Base Documents and their values and references. It also emphasizes the difference between the support system and the interface system when there is a functional connection between different systems.

SAFT-UT utilities: Guide to SAFT-UT principles and conventions

International Nuclear Information System (INIS)

Hall, T.E.

1987-10-01

This guide, the Guide to SAFT-UT (Synthetic Aperture Focusing Technique-Ultrasonic Testing), Principles and Conventions, is intended to provide the user with an overall background for practical implementation of SAFT-UT and the associated software utilities. It is not intended to exhaustively cover each related item, but rather to supply information from theory and experience that will assist the serious user in exploiting the robust nature of the SAFT technology. Chapter 1 gives an introductory overview from a historical perspective, emphasizing the need to maintain data integrity throughout the SAFT-UT imaging process. Chapter 2 includes a theoretical description of the Three SAFT-UT configurations currently being supported (single transducer pulse-echo, TSAFT, and TSAFT-2). A general description of the software tools is given in Chapter 3. It describes the major utilities and the general use of each one. Chapter 4 deals with the system resolution and sampling demands of SAFT-UT. A discussion of the strengths and limitations of the SAFT technique is provided in Chapter 5. The scanning conventions assumed throughout the implementation of the SAFT-UT utilities are detailed in Chapter 6. Chapter 7 lists an exhaustive supply of references for the user desiring to investigate the SAFT technology further. 26 refs., 19 figs

Pharmacobezoars described and demystified.

Science.gov (United States)

Simpson, Serge-Emile

2011-02-01

A bezoar is a concretion of foreign material that forms and persists in the gastrointestinal tract. Bezoars are classified by their material origins. Phytobezoars contain plant material, trichobezoars contain hair, lactobezoars contain milk proteins, and pharmacobezoars contain pharmaceutical products. Tablets, suspensions, and even insoluble drug delivery vehicles can, on rare occasions, and sometimes under specific circumstances, form pharmacobezoars. The goal of this review is to catalog and examine all of the available reports in the English language medical literature that convincingly describe the formation and management of pharmacobezoars. Articles included in this review were identified by performing searches using the terms "bezoar," "pharmacobezoar," and "concretion" in the following databases: OVID MEDLINE, PubMed, and JSTOR. The complete MEDLINE and JSTOR holdings were included in the search without date ranges. The results were limited to English language publications. Articles that described nonmedication bezoars were not included in the review. Articles describing phytobezoars, food bezoars, fecal impactions, illicit drug packet ingestions, enteral feeding material bezoars, and hygroscopic diet aid bezoars were excluded. The bibliographic references within the articles already accumulated were then examined in order to gather additional pharmacobezoar cases. The cases are grouped by pharmaceutical agent that formed the bezoar, and groupings are arranged in alphabetical order. Discussions and conclusions specific to each pharmaceutical agent are included in that agent's subheading. Patterns and themes that emerged in the review of the assembled case reports are reviewed and presented in a more concise format. Pharmacobezoars form under a wide variety of circumstances and in a wide variety of patients. They are difficult to diagnose reliably. Rules for suspecting, diagnosing, and properly managing a pharmacobezoar are highly dependent on the

Security guide for subcontractors

Energy Technology Data Exchange (ETDEWEB)

Adams, R.C.

1993-06-01

This guide is provided to aid in the achievement of security objectives in the Department of Energy (DOE) contractor/subcontractor program. The objectives of security are to protect information that, if released, would endanger the common defense and security of the nation and to safeguard plants and installations of the DOE and its contractors to prevent the interruption of research and production programs. The security objective and means of achieving the objective are described. Specific security measures discussed in this guide include physical barriers, personnel identification systems, personnel and vehicular access control, classified document control, protection of classified matter in use, storing classified matter, and repository combinations. Means of dealing with security violations and security infractions are described. Maintenance of a security education program is discussed. Also discussed are methods of handling clearance terminations, visitor control, travel to sensitive countries, and shipment security. The Technical Surveillance Countermeasures Program (TSCM), the Computer Security Program, and the Operations Security Plan (OPSEC) are examined.

rf reference line for PEP

International Nuclear Information System (INIS)

Schwarz, H.D.; Weaver, J.N.

1979-03-01

A rf phase reference line in 6 segments around the 2200 meter circumference PEP storage ring is described. Each segment of the reference line is phase stabilized by its own independent feedback system, which uses an amplitude modulated reflection from the end of each line. The modulation is kept small and decoupled from the next segment to avoid crosstalk and significant modulation of the rf drive signal. An error evaluation of the system is made. The technical implementation and prototype performance are described. Prototype tests indicate that the phase error around the ring can be held below 1 degree with this relatively simple system

rf reference line for PEP

Energy Technology Data Exchange (ETDEWEB)

Schwarz, H.D.; Weaver, J.N.

1979-03-01

A rf phase reference line in 6 segments around the 2200 meter circumference PEP storage ring is described. Each segment of the reference line is phase stabilized by its own independent feedback system, which uses an amplitude modulated reflection from the end of each line. The modulation is kept small and decoupled from the next segment to avoid crosstalk and significant modulation of the rf drive signal. An error evaluation of the system is made. The technical implementation and prototype performance are described. Prototype tests indicate that the phase error around the ring can be held below 1 degree with this relatively simple system.

A Planning Guide for Instructional Networks, Part I.

Science.gov (United States)

Daly, Kevin F.

1994-01-01

Discusses three phases in implementing a master plan for a school-based local area network (LAN): (1) network software selection; (2) hardware selection, network topology, and site preparation; and (3) implementation time table. Sample planning and specification worksheets and a list of planning guides are included. (Contains six references.) (KRN)

Guide to radiological accident considerations for siting and design of DOE nonreactor nuclear facilities

International Nuclear Information System (INIS)

Elder, J.; Graf, J.M.

1984-01-01

DOE Office of Nuclear Safety has sponsored preparation of a guidance document to aid field offices and contractors in their analyses of consequences of postulated major accidents. The guide addresses the requirements of DOE Orders 5480.1A, Chapter V, and 6430.1, including the general requirement that DOE nuclear facilities be sited, designed, and operated in accordance with standards, codes, and guides consistent with those applied to comparable licensed nuclear facilities. The guide includes both philosophical and technical information in the areas of: siting guidelines doses applied to an offsite reference person; consideration also given to an onsite reference person; physical parameters, models, and assumptions to be applied when calculating doses for comparison to siting criteria; and potential accident consequences other than radiological dose to a reference person which might affect siting and major design features of the facility, such as environmental contamination, population dose, and associated public health effects. Recommendations and/or clarifications are provided where this could be done without adding new requirements. In this regard, the guide is considered a valuable aid to the safety analyst, especially where requirements have been subject to inconsistent interpretation or where analysis methods are in transition, such as use of dose model (ICRP 2 or ICRP 30) or use of probabilistic methods of risk analysis in the siting and design of nuclear facilities

Framework for a low-cost intra-operative image-guided neuronavigator including brain shift compensation.

Science.gov (United States)

Bucki, M; Lobos, C; Payan, Y

2007-01-01

In this paper we present a methodology to address the problem of brain tissue deformation referred to as 'brain-shift'. This deformation occurs throughout a neurosurgery intervention and strongly alters the accuracy of the neuronavigation systems used to date in clinical routine which rely solely on pre-operative patient imaging to locate the surgical target, such as a tumour or a functional area. After a general description of the framework of our intra-operative image-guided system, we describe a procedure to generate patient specific finite element meshes of the brain and propose a biomechanical model which can take into account tissue deformations and surgical procedures that modify the brain structure, like tumour or tissue resection.

235Uranium isotope abundance certified reference material for gamma spectrometry EC nuclear reference material 171 certification report

International Nuclear Information System (INIS)

De Bievre, P.; Eschbach, H.L.; Lesser, R.; Meyer, H.; Audenhove, Van J.

1986-01-01

This certification report contains the information necessary for the final certification of EC nuclear reference material 171. It is also intended to inform the user of the reference material concerned on technical/scientific details which are not given in the certificate. The report describes the reference material which consists of sets of U 3 O 8 samples with five different 235 U/U abundances, filled in cylindrical aluminium cans. The can bottom serves as window for emitted gamma radiation. The report describes how the 235 U/U abundances were characterized, how the other properties relevant for gamma measurements were determined and gives all connected results as well as those from the verification measurements. Appendix A represents the draft certificate. 32 refs

OpenCL programming guide

CERN Document Server

Munshi, Aaftab; Mattson, Timothy G; Fung, James; Ginsburg, Dan

2011-01-01

Using the new OpenCL (Open Computing Language) standard, you can write applications that access all available programming resources: CPUs, GPUs, and other processors such as DSPs and the Cell/B.E. processor. Already implemented by Apple, AMD, Intel, IBM, NVIDIA, and other leaders, OpenCL has outstanding potential for PCs, servers, handheld/embedded devices, high performance computing, and even cloud systems. This is the first comprehensive, authoritative, and practical guide to OpenCL 1.1 specifically for working developers and software architects. Written by five leading OpenCL authorities, OpenCL Programming Guide covers the entire specification. It reviews key use cases, shows how OpenCL can express a wide range of parallel algorithms, and offers complete reference material on both the API and OpenCL C programming language. Through complete case studies and downloadable code examples, the authors show how to write complex parallel programs that decompose workloads across many different devices. They...

Image guided prostate cancer treatments

Energy Technology Data Exchange (ETDEWEB)

Bard, Robert L. [Bard Cancer Center, Biofoundation for Angiogenesis Research and Development, New York, NY (United States); Fuetterer, Jurgen J. [Radboud Univ. Nijmegen, Medical Centre (Netherlands). Dept. of Radiology; Sperling, Dan (ed.) [Sperling Prostate Center, Alpha 3TMRI, New York, NY (United States)

2014-07-01

Systematic overview of the application of ultrasound and MRI in the diagnosis and treatment of diseases of the lower urinary tract. Detailed information on image-guided therapies, including focused ultrasound, photodynamic therapy, and microwave and laser ablation. Numerous high-quality illustrations based on high-end equipment. Represents the state of the art in Non Invasive Imaging and Minimally Invasive Ablation Treatment (MIAT). Image-Guided Prostate Cancer Treatments is a comprehensive reference and practical guide on the technology and application of ultrasound and MRI in the male pelvis, with special attention to the prostate. The book is organized into three main sections, the first of which is devoted to general aspects of imaging and image-guided treatments. The second section provides a systematic overview of the application of ultrasound and MRI to the diagnosis and treatment of diseases of the lower urinary tract. Performance of the ultrasound and MRI studies is explained, and the normal and abnormal pathological anatomy is reviewed. Correlation with the ultrasound in the same plane is provided to assist in understanding the MRI sequences. Biopsy and interventional procedures, ultrasound-MRI fusion techniques, and image-guided therapies, including focused ultrasound, photodynamic therapy, microwave and laser ablation, are all fully covered. The third section focuses on securing treatment effectiveness and the use of follow-up imaging to ensure therapeutic success and detect tumor recurrence at an early stage, which is vital given that prompt focal treatment of recurrence is very successful. Here, particular attention is paid to the role of Doppler ultrasound and DCE-MRI technologies. This book, containing a wealth of high-quality illustrations based on high-end equipment, will acquaint beginners with the basics of prostate ultrasound and MRI, while more advanced practitioners will learn new skills, means of avoiding pitfalls, and ways of effectively

Core management and fuel handling for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2004-01-01

This Safety Guide supplements and elaborates upon the safety requirements for core management and fuel handling that are presented in Section 5 of the Safety Requirements publication on the operation of nuclear power plants. The present publication supersedes the IAEA Safety Guide on Safety Aspects of Core Management and Fuel Handling, issued in 1985 as Safety Series No. 50-SG-010. It is also related to the Safety Guide on the Operating Organization for Nuclear Power Plants, which identifies fuel management as one of the various functions to be performed by the operating organization. The purpose of this Safety Guide is to provide recommendations for core management and fuel handling at nuclear power plants on the basis of current international good practice. The present Safety Guide addresses those aspects of fuel management activities that are necessary in order to allow optimum reactor core operation without compromising the limits imposed by the design safety considerations relating to the nuclear fuel and the plant as a whole. In this publication, 'core management' refers to those activities that are associated with fuel management in the core and reactivity control, and 'fuel handling' refers to the movement, storage and control of fresh and irradiated fuel. Fuel management comprises both core management and fuel handling. This Safety Guide deals with fuel management for all types of land based stationary thermal neutron power plants. It describes the safety objectives of core management, the tasks that have to be accomplished to meet these objectives and the activities undertaken to perform those tasks. It also deals with the receipt of fresh fuel, storage and handling of fuel and other core components, the loading and unloading of fuel and core components, and the insertion and removal of other reactor materials. In addition, it deals with loading a transport container with irradiated fuel and its preparation for transport off the site. Transport

Core management and fuel handling for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2002-01-01

This Safety Guide supplements and elaborates upon the safety requirements for core management and fuel handling that are presented in Section 5 of the Safety Requirements publication on the operation of nuclear power plants. The present publication supersedes the IAEA Safety Guide on Safety Aspects of Core Management and Fuel Handling, issued in 1985 as Safety Series No. 50-SG-010. It is also related to the Safety Guide on the Operating Organization for Nuclear Power Plants, which identifies fuel management as one of the various functions to be performed by the operating organization. The purpose of this Safety Guide is to provide recommendations for core management and fuel handling at nuclear power plants on the basis of current international good practice. The present Safety Guide addresses those aspects of fuel management activities that are necessary in order to allow optimum reactor core operation without compromising the limits imposed by the design safety considerations relating to the nuclear fuel and the plant as a whole. In this publication, 'core management' refers to those activities that are associated with fuel management in the core and reactivity control, and 'fuel handling' refers to the movement, storage and control of fresh and irradiated fuel. Fuel management comprises both core management and fuel handling. This Safety Guide deals with fuel management for all types of land based stationary thermal neutron power plants. It describes the safety objectives of core management, the tasks that have to be accomplished to meet these objectives and the activities undertaken to perform those tasks. It also deals with the receipt of fresh fuel, storage and handling of fuel and other core components, the loading and unloading of fuel and core components, and the insertion and removal of other reactor materials. In addition, it deals with loading a transport container with irradiated fuel and its preparation for transport off the site. Transport

Overview of the PMBOK Guide

CERN Document Server

O'Conchuir, Deasun

2011-01-01

This book is for everyone who wants a readable introduction to best practice Project Management, as described by the PMBOK(R) Guide 4th Edition of the Project Management Institute (PMI), "the world's leading association for the project management profession." It is particularly useful for applicants for the PMI's PMP(R) (Project Management Professional) and CAPM(R) (Certified Associate of Project Management) examinations, which are based mostly on the PMBOK(R) Guide. This book can also be studied alone by anyone as a general introduction to Project Management. The style and language

Field guide to nonlinear optics

CERN Document Server

Powers, Peter E

2013-01-01

Optomechanics is a field of mechanics that addresses the specific design challenges associated with optical systems. This [i]Field Guide [/i]describes how to mount optical components, as well as how to analyze a given design. It is intended for practicing optical and mechanical engineers whose work requires knowledge in both optics and mechanics. This Field Guide is designed for those looking for a condensed and concise source of key concepts, equations, and techniques for nonlinear optics. Topics covered include technologically important effects, recent developments in nonlinear optics

Management of soils polluted by activities of a basic nuclear installations. Guide Nr 24, Release of the 2016/08/30

International Nuclear Information System (INIS)

2016-01-01

After having indicated the relevant regulatory texts and guides related to sanitation and dismantling, and having stated definitions of some important terms, this guide addresses the sanitation or soil management approach to be adopted as soon as a soil pollution requires it. This pollution can be radioactive or chemical, and the case of a pollution going out of the installation is also included. Legal responsibility is outlined. The guide aims then at detailing the articulation between the various concerned and relevant documents for the management of a radioactive or chemical pollution related to the activities of a basic nuclear installation (BNI), and at detailing ASN expectations in this respect. Thus, it recalls the adopted management approach and methodological tools: diagnosis, interpretation of environment condition, management plan. It describes the approach related to soil sanitation: diagnosis, document to be produced, field and additional investigations, implementation of the reference approach for a complete removal of pollution, actions to be undertaken when the application of the reference approach is impossible, end of sanitation works. The third part discusses the methodology of soil sanitation by excavation by distinguishing three defence lines, by discussing the management of excavated soils (management modalities, warehousing within the installation). Administrative procedures to be applied before, during and after sanitation works are then presented. Specific management approaches are indicated for a BNI being operated or being dismantled. Actions of information are also indicated. Finally, requirements in terms of quality assurance are evoked

Safety assessment and verification for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2001-01-01

verification' are used differently in different countries. The way that these terms have been used in this Safety Guide is explained in Section 2. The term 'design' as used here includes the specifications for the safe operation and management of the plant. This Safety Guide identifies the key recommendations for carrying out the safety assessment and the independent verification. It provides detailed guidance in support of IAEA, Safety of Nuclear Power Plants: Design, Safety Standards Series No. NS-R-1 (2000), particularly in the area of safety analysis. However, this does not include all the technical details which are available and reference is made to other IAEA publications on specific design issues and safety analysis methods. Specific deterministic or probabilistic safety targets or radiological limits can vary in different countries and are the responsibility of the regulatory body. This Safety Guide provides some references to targets and limits established by international organizations. Operators, and sometimes designers, may also set their own safety targets which may be more stringent than those set by the regulator or may address different aspects of safety. In some countries operators are expected to do this as part of their 'ownership' of the entire safety case. This Safety Guide does not include specific recommendations for the safety assessment of those plant systems for which dedicated Safety Guides exist. Section 2 defines the terms 'safety assessment', 'safety analysis' and 'independent verification' and outlines their relationship. Section 3 gives the key recommendations for the safety assessment of the principal and plant design requirements. Section 4 gives the key recommendations for safety analysis. It describes the identification of postulated initiating events (PIEs), which are used throughout the safety assessment including the safety analysis, the deterministic transient analysis and severe accident analysis, and the probabilistic safety analysis

[Ultrasound-guided peripheral catheterization].

Science.gov (United States)

Salleras-Duran, Laia; Fuentes-Pumarola, Concepció

2016-01-01

Peripheral catheterization is a technique that can be difficult in some patients. Some studies have recently described the use of ultrasound to guide the venous catheterization. To describe the success rate, time required, complications of ultrasound-guided peripheral venous catheterization. and patients and professionals satisfaction The search was performed in databases (Medline-PubMed, Cochrane Library, CINAHL and Cuiden Plus) for studies published about ultrasound-guided peripheral venous catheterization performed on patients that provided results on the success of the technique, complications, time used, patient satisfaction and the type of professional who performed the technique. A total of 21 studies were included. Most of them get a higher success rate 80% in the catheterization ecoguide and time it is not higher than the traditional technique. The Technical complications analyzed were arterial puncture rates and lower nerve 10%. In all studies measuring and comparing patient satisfaction in the art ecoguide is greater. Various professional groups perform the technique. The use of ultrasound for peripheral pipes has a high success rate, complications are rare and the time used is similar to that of the traditional technique. The technique of inserting catheters through ultrasound may be learned by any professional group performing venipuncture. Finally, it gets underscores the high patient satisfaction with the use of this technique. Copyright © 2015 Elsevier España, S.L.U. All rights reserved.

Image-Guided Cancer Nanomedicine

Directory of Open Access Journals (Sweden)

Dong-Hyun Kim

2018-01-01

Full Text Available Multifunctional nanoparticles with superior imaging properties and therapeutic effects have been extensively developed for the nanomedicine. However, tumor-intrinsic barriers and tumor heterogeneity have resulted in low in vivo therapeutic efficacy. The poor in vivo targeting efficiency in passive and active targeting of nano-therapeutics along with the toxicity of nanoparticles has been a major problem in nanomedicine. Recently, image-guided nanomedicine, which can deliver nanoparticles locally using non-invasive imaging and interventional oncology techniques, has been paid attention as a new opportunity of nanomedicine. This short review will discuss the existing challenges in nanomedicine and describe the prospects for future image-guided nanomedicine.

Apache The Definitive Guide

CERN Document Server

Laurie, Ben

2003-01-01

Apache is far and away the most widely used web server platform in the world. This versatile server runs more than half of the world's existing web sites. Apache is both free and rock-solid, running more than 21 million web sites ranging from huge e-commerce operations to corporate intranets and smaller hobby sites. With this new third edition of Apache: The Definitive Guide, web administrators new to Apache will come up to speed quickly, and experienced administrators will find the logically organized, concise reference sections indispensable, and system programmers interested in customizin

Extensions of guiding center motion to higher order

International Nuclear Information System (INIS)

Northrop, T.G.; Rome, J.A.

1978-01-01

In a static magnetic field, some well-known guiding center equations maintain their form when extended to next order in gyroradius. In these cases, it is only necessary to include the next order term in the magnetic moment series. The differential equation for guiding center motion which describes both the parallel and perpendicular velocities correctly through first order in gyroradius is given. The question of how to define the guiding center position through second order arises and is discussed, and second order drifts are derived for one usual definition. The toroidal canonical angular momentum, P/sub phi/, of the guiding center in an axisymmetric field is shown to be conserved using the guiding center velocity correct through first order. When second-order motion is included, P/sub phi/ is no longer a constant. The above extensions of guiding center theory help to resolve the different tokamak orbits obtained either by using the guiding center equations of motion or by using conservation of P/sub phi/

Extensions of guiding center motion to higher order

International Nuclear Information System (INIS)

Northrop, T.G.; Rome, J.A.

1977-07-01

In a static magnetic field, some well-known guiding center equations maintain their form when extended to next order in gyroradius. In these cases, it is only necessary to include the next order term in the magnetic moment series. The differential equation for guiding center motion which describes both the parallel and perpendicular velocities correctly through first order in gyroradius is given. The question of how to define the guiding center position through second order arises and is discussed, and second order drifts are derived for one usual definition. The toroidal canonical angular momentum, P/sub phi/, of the guiding center in an axisymmetric field is shown to be conserved using the guiding center velocity correct through first order. When second order motion is included, P/sub phi/ is no longer a constant. The above extensions of guiding center theory help to resolve the different tokamak orbits obtained either by using the guiding center equations of motion or by using conservation of P/sub phi/

Apollo for Adobe Flex Developers Pocket Guide A Developer's Reference for Apollo's Alpha Release

CERN Document Server

Chambers, Mike; Swartz, Jeff

2009-01-01

Now you can build and deploy Flash-based Rich Internet Applications (RIAs) to the desktop using Adobe's Flex framework. Written by members of the Apollo product team, this is the official guide to the Alpha release of Adobe Apollo, the new cross platform desktop runtime from Adobe Labs. Numerous examples illustrate how Apollo works so you can start building RIAs for the desktop right away.

Alcohol Abuse Curriculum Guide for Nurse Practitioner Faculty. Health Professions Education Curriculum Resources Series. Nursing 3.

Science.gov (United States)

Hasselblad, Judith

The format for this curriculum guide, written for nurse practitioner faculty, consists of learning objectives, content outline, teaching methodology suggestions, references and recommended readings. Part 1 of the guide, Recognition of Early and Chronic Alcoholism, deals with features of alcoholism such as epidemiological data and theories,…

HAPPIER: Health Resource Guide.

Science.gov (United States)

Pennsylvania State Dept. of Education, Harrisburg.

Based on findings of Project HAPPIER surveys and intended as a resource for health care providers and educators who serve the migrant community, this guide describes over 375 instructional materials in the areas of dental health, disease control, fitness, health promotion, human growth and development, hypertension, maternal and child care, mental…

A Nurse's Survival Guide to the Ward - Third edition Richards Ann Edwards Sharon A Nurse's Survival Guide to the Ward - Third edition 500pp £19.99 Elsevier 978 0 7020 4603 2 0702046035 [Formula: see text].

Science.gov (United States)

2013-05-08

This guide is a useful 'friend and companion' to keep close at hand. It is an essential reference for nurses, not only on the ward but in every field of practice where patient care is given. In fact, it makes an accessible guide for all healthcare practitioners.

Nuclear power a reference handbook

CERN Document Server

Henderson, Harry R

2014-01-01

In the 21st century, nuclear power has been identified as a viable alternative to traditional energy sources to stem global climate change, and condemned as risky to human health and environmentally irresponsible. Do the advantages of nuclear energy outweigh the risks, especially in light of the meltdown at the Fukushima plant in 2011? This guide provides both a comprehensive overview of this critical and controversial technology, presenting reference tools that include important facts and statistics, biographical profiles, a chronology, and a glossary. It covers major controversies and proposed solutions in detail and contains contributions by experts and important stakeholders that provide invaluable perspective on the topic.

The Use of Reference Models in Business Process Renovation

Directory of Open Access Journals (Sweden)

Dejan Pajk

2010-01-01

Full Text Available Enterprise resource planning (ERP systems are often used by companies to automate and enhance their busi- ness processes. The capabilities of ERP systems can be described by best-practice reference models. The purpose of the article is to demonstrate the business process renovation approach with the use of reference models. Although the use of reference models brings many positive effects for business, they are still rarely used in Slovenian small and medium-sized compa- nies. The reasons for this may be found in the reference models themselves as well as in project implementation methodologies. In the article a reference model based on Microsoft Dynamics NAV is suggested. The reference model is designed using upgraded BPMN notation with additional business objects, which help to describe the models in more detail.

A Guided Inquiry Activity for Teaching Ligand Field Theory

Science.gov (United States)

Johnson, Brian J.; Graham, Kate J.

2015-01-01

This paper will describe a guided inquiry activity for teaching ligand field theory. Previous research suggests the guided inquiry approach is highly effective for student learning. This activity familiarizes students with the key concepts of molecular orbital theory applied to coordination complexes. Students will learn to identify factors that…

The uncertainty of reference standards--a guide to understanding factors impacting uncertainty, uncertainty calculations, and vendor certifications.

Science.gov (United States)

Gates, Kevin; Chang, Ning; Dilek, Isil; Jian, Huahua; Pogue, Sherri; Sreenivasan, Uma

2009-10-01

Certified solution standards are widely used in forensic toxicological, clinical/diagnostic, and environmental testing. Typically, these standards are purchased as ampouled solutions with a certified concentration. Vendors present concentration and uncertainty differently on their Certificates of Analysis. Understanding the factors that impact uncertainty and which factors have been considered in the vendor's assignment of uncertainty are critical to understanding the accuracy of the standard and the impact on testing results. Understanding these variables is also important for laboratories seeking to comply with ISO/IEC 17025 requirements and for those preparing reference solutions from neat materials at the bench. The impact of uncertainty associated with the neat material purity (including residual water, residual solvent, and inorganic content), mass measurement (weighing techniques), and solvent addition (solution density) on the overall uncertainty of the certified concentration is described along with uncertainty calculations.

Toolkit for Conceptual Modeling (TCM): User's Guide and Reference

NARCIS (Netherlands)

Dehne, F.; Wieringa, Roelf J.

1997-01-01

The Toolkit for Conceptual Modeling (TCM) is a suite of graphical editors for a number of graphical notation systems that are used in software specification methods. The notations can be used to represent the conceptual structure of the software - hence the name of the suite. This manual describes

Development of anabolic-androgenic steroids purity certified reference materials for anti-doping.

Science.gov (United States)

Quan, Can; Su, Fuhai; Wang, Haifeng; Li, Hongmei

2011-12-20

The need for certified reference materials (CRM) of anabolic-androgenic steroids reference materials was emphasized by the Beijing 2008 Olympic game as a tool to improve comparability, ensuring accuracy and traceability of analytical results for competing athletes. The China National Institute of Metrology (NIM) responded to the state request by providing seven anabolic-androgenic steroids (AAS) reference materials for Beijing Olympic anti-doping, GBW (E) 100086-GBW (E) 100092. This work describes the production of the series of AAS CRMs, according to ISO Guides 34 and 35 [1,2], which comprises the material processing, homogeneity and stability assessment, CRMs' characterization including moisture content, trace metal content. The AASs' purity values were assigned with collaborative study involved eight laboratories applying high resolution liquid chromatography-diode array detector (HPLC-DAD). Homogeneity of the AAS CRMs were determined by an in-house validated liquid chromatographic methodology. Potential degradation during storage was also investigated and a shelf-life based on this value was established. The certified values of CRMs were 99.76±0.079%, 99.76±0.25%, 99.63±0.09%, 99.67±0.11%, 98.82±0.56%, 96.30±0.39% and 99.71±0.49% (purity±expanded uncertainty with confidence level of 95%) for methyltestosterone, testosterone propionate, nandrolone, nandrolone 17-propionate, boldenone, trenbolone acetate and testosterone respectively. The certified values for all the studied AAS reference materials are traceable to the international system of units (SI). The CRMs developed were applied by 32 laboratory including sports organizations and analytical laboratories during the 2008 Olympic game for anti-doping control. Copyright © 2011 Elsevier Inc. All rights reserved.

Mobility-based Time References for Wireless Sensor Networks

CERN Document Server

Sebastiano, Fabio; Makinwa, Kofi A A

2013-01-01

 This book describes the use of low-power low-cost and extremely small radios to provide essential time reference for wireless sensor networks.  The authors explain how to integrate such radios in a standard CMOS process to reduce both cost and size, while focusing on the challenge of designing a fully integrated time reference for such radios. To enable the integration of the time reference, system techniques are proposed and analyzed, several kinds of integrated time references are reviewed, and mobility-based references are identified as viable candidates to provide the required accuracy at low-power consumption. Practical implementations of a mobility-based oscillator and a temperature sensor are also presented, which demonstrate the required accuracy over a wide temperature range, while drawing 51-uW from a 1.2-V supply in a 65-nm CMOS process. Provides system analysis to understand requirements for time/frequency accuracy in wireless sensor networks; Describes system optimization for time references i...

MRI-guided vacuum-assisted breast biopsy: comparison with stereotactically guided and ultrasound-guided techniques

Energy Technology Data Exchange (ETDEWEB)

Imschweiler, Thomas; Freiwald, Bianka; Kubik-Huch, Rahel A. [Kantonspital Baden AG, Institute for Radiology, Baden (Switzerland); Haueisen, Harald [Kantonspital Aarau AG, Institute for Radiology, Aarau (Switzerland); Kampmann, Gert [Clinica Sant' Anna, Lugano, Sorengo (Switzerland); Rageth, Luzi [Adjumed Services AG, Zurich (Switzerland); Seifert, Burkhardt [Institute for Social and Preventive Medicine, University of Zurich, Division of Biostatistics, Zuerich (Switzerland); Rageth, Christoph [Breast Centre, Zurich (Switzerland)

2014-01-15

To analyse the development of MRI-guided vacuum-assisted biopsy (VAB) in Switzerland and to compare the procedure with stereotactically guided and ultrasound-guided VAB. We performed a retrospective analysis of VABs between 2009 and 2011. A total of 9,113 VABs were performed. Of these, 557 were MRI guided. MRI-guided VAB showed the highest growth rate (97 %) of all three procedures. The technical success rates for MRI-guided, stereotactically guided and ultrasound-guided VAB were 98.4 % (548/557), 99.1 % (5,904/5,960) and 99.6 % (2,585/2,596), respectively. There were no significant differences (P = 0.12) between the MRI-guided and the stereotactically guided procedures. The technical success rate for ultrasound-guided VAB was significantly higher than that for MRI-guided VAB (P < 0.001). There were no complications using MRI-guided VAB requiring open surgery. The malignancy diagnosis rate for MRI-guided VAB was similar to that for stereotactically guided VAB (P = 0.35). MRI-guided VAB is a safe and accurate procedure that provides insight into clinical breast findings. (orig.)

Using the International Classification of Functioning, Disability and Health (ICF to describe children referred to special care or paediatric dental services.

Directory of Open Access Journals (Sweden)

Denise Faulks

Full Text Available Children in dentistry are traditionally described in terms of medical diagnosis and prevalence of oral disease. This approach gives little information regarding a child's capacity to maintain oral health or regarding the social determinants of oral health. The biopsychosocial approach, embodied in the International Classification of Functioning, Disability and Health - Child and Youth version (ICF-CY (WHO, provides a wider picture of a child's real-life experience, but practical tools for the application of this model are lacking. This article describes the preliminary empirical study necessary for development of such a tool - an ICF-CY Core Set for Oral Health. An ICF-CY questionnaire was used to identify the medical, functional, social and environmental context of 218 children and adolescents referred to special care or paediatric dental services in France, Sweden, Argentina and Ireland (mean age 8 years ± 3.6 yrs. International Classification of Disease (ICD-10 diagnoses included disorders of the nervous system (26.1%, Down syndrome (22.0%, mental retardation (17.0%, autistic disorders (16.1%, and dental anxiety alone (11.0%. The most frequently impaired items in the ICF Body functions domain were 'Intellectual functions', 'High-level cognitive functions', and 'Attention functions'. In the Activities and Participation domain, participation restriction was frequently reported for 25 items including 'Handling stress', 'Caring for body parts', 'Looking after one's health' and 'Speaking'. In the Environment domain, facilitating items included 'Support of friends', 'Attitude of friends' and 'Support of immediate family'. One item was reported as an environmental barrier - 'Societal attitudes'. The ICF-CY can be used to highlight common profiles of functioning, activities, participation and environment shared by children in relation to oral health, despite widely differing medical, social and geographical contexts. The results of this empirical

Methodological guide: management of industrial sites potentially contaminated by radioactive substances; Guide methodologique: gestion des sites industriels potentiellement contamines par des substances radioactives

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

At the request of the Ministries of Health and the Environment, IPSN is preparing and publishing the first version of the methodological guide devoted to managing industrial sites potentially contaminated by radioactive substances. This guide describes a procedure for defining and choosing strategies for rehabilitating such industrial sites. (author)

Guide on Project Web Access of SFR R and D and Technology Monitoring System

International Nuclear Information System (INIS)

Lee, Dong Uk; Won, Byung Chool; Lee, Yong Bum; Kim, Young In; Hahn, Do Hee

2008-09-01

The SFR R and D and technology monitoring system based on the MS enterprise project management is developed for systematic effective management of 'Development of Basic Key Technologies for Gen IV SFR' project which was performed under the Mid- and Long-term Nuclear R and D Program sponsored by the Ministry of Education, Science and Technology. This system is a tool for project management based on web access. Therefore this manual is a detailed guide for Project Web Access(PWA). Section 1 describes the common guide for using of system functions such as project server 2007 client connection setting, additional outlook function setting etc. The section 2 describes the guide for system administrator. It is described the guide for project management in section 3, 4

Guide on Project Web Access of SFR R and D and Technology Monitoring System

Energy Technology Data Exchange (ETDEWEB)

Lee, Dong Uk; Won, Byung Chool; Lee, Yong Bum; Kim, Young In; Hahn, Do Hee

2008-09-15

The SFR R and D and technology monitoring system based on the MS enterprise project management is developed for systematic effective management of 'Development of Basic Key Technologies for Gen IV SFR' project which was performed under the Mid- and Long-term Nuclear R and D Program sponsored by the Ministry of Education, Science and Technology. This system is a tool for project management based on web access. Therefore this manual is a detailed guide for Project Web Access(PWA). Section 1 describes the common guide for using of system functions such as project server 2007 client connection setting, additional outlook function setting etc. The section 2 describes the guide for system administrator. It is described the guide for project management in section 3, 4.

REFERENCE MATERIALS IN THE SPHERE OF USE OF ATOMIC ENERGY

Directory of Open Access Journals (Sweden)

V. A. Borisov

2015-01-01

Full Text Available The article describes the chronology of development of the system of reference materials in the nuclear industry of the Russian Federation. The basic documents used in the sphere of nuclear energy are described. The nomenclature of reference materials and feature of their application in the "Rosatom" is given. The prospects of development activities in the field of reference materials are formulated.

Technical reference manual for TIME4. Vol. 2

International Nuclear Information System (INIS)

Wilmot, R.D.; Ringrose, P.S.; Larkin, J.P.A.; Kleissen, F.A.T.

1991-07-01

This document is the Technical Reference Manual for the TIME4 model. TIME4 is the environmental change model developed for use in the probabilistic risk analysis of deep disposal of radioactive waste. The Technical Reference Manual describes the theoretical background to the model. The modelling method is described, followed by a review of related work and a detailed description for each sub-model. (author)

An investigation of the potential of rapid prototyping technology for image‐guided surgery

Science.gov (United States)

Rajon, Didier A.; Bova, Frank J.; Bhasin, R. Rick; Friedman, William A.

2006-01-01

Image‐guided surgery can be broken down into two broad categories: frame‐based guidance and frameless guidance. In order to reduce both the invasive nature of stereotactic guidance and the cost in equipment and time, we have developed a new guidance technique based on rapid prototyping (RP) technology. This new system first builds a computer model of the patient anatomy and then fabricates a physical reference frame that provides a precise and unique fit to the patient anatomy. This frame incorporates a means of guiding the surgeon along a preplanned surgical trajectory. This process involves (1) obtaining a high‐resolution CT or MR scan, (2) building a computer model of the region of interest, (3) developing a surgical plan and physical guide, (4) designing a frame with a unique fit to the patient's anatomy with a physical linkage to the surgical guide, and (5) fabricating the frame using an RP unit. Software was developed to support these processes. To test the accuracy of this process, we first scanned and reproduced a plastic phantom fabricated to validate the system's ability to build an accurate virtual model. A target on the phantom was then identified, a surgical approach planned, a surgical guide designed, and the accuracy and precision of guiding a probe to that target were determined. Steps 1 through 5 were also evaluated using a head phantom. The results show that the RP technology can replicate an object from CT scans with submillimeter resolution. The fabricated reference frames, when positioned on the surface of the phantom and used to guide a surgical probe, can position the probe tip with an accuracy of 1.7 mm at the probe tip. These results demonstrate that the RP technology can be used for the fabrication of customized positioning frames for use in image‐guided surgery. PACS number: 87.57.Gg PMID:17533357

Preclosure Safety Analysis Guide

International Nuclear Information System (INIS)

D.D. Orvis

2003-01-01

A preclosure safety analysis (PSA) is a required element of the License Application (LA) for the high- level radioactive waste repository at Yucca Mountain. This guide provides analysts and other Yucca Mountain Repository Project (the Project) personnel with standardized methods for developing and documenting the PSA. The definition of the PSA is provided in 10 CFR 63.2, while more specific requirements for the PSA are provided in 10 CFR 63.112, as described in Sections 1.2 and 2. The PSA requirements described in 10 CFR Part 63 were developed as risk-informed performance-based regulations. These requirements must be met for the LA. The PSA addresses the safety of the Geologic Repository Operations Area (GROA) for the preclosure period (the time up to permanent closure) in accordance with the radiological performance objectives of 10 CFR 63.111. Performance objectives for the repository after permanent closure (described in 10 CFR 63.113) are not mentioned in the requirements for the PSA and they are not considered in this guide. The LA will be comprised of two phases: the LA for construction authorization (CA) and the LA amendment to receive and possess (R and P) high-level radioactive waste (HLW). PSA methods must support the safety analyses that will be based on the differing degrees of design detail in the two phases. The methods described herein combine elements of probabilistic risk assessment (PRA) and deterministic analyses that comprise a risk-informed performance-based safety analysis. This revision to the PSA guide was prepared for the following objectives: (1) To correct factual and typographical errors. (2) To provide additional material suggested from reviews by the Project, the U.S. Department of Energy (DOE), and U.S. Nuclear Regulatory Commission (NRC) Staffs. (3) To update material in accordance with approaches and/or strategies adopted by the Project. In addition, a principal objective for the planned revision was to ensure that the methods and

An Instructor's Guide for a Program in Brake Services.

Science.gov (United States)

New York State Education Dept., Albany. Bureau of Secondary Curriculum Development.

The instructor's guide is designed to present an understanding of the automotive hydraulic brake system and to help individuals develop new skills for employment in this specialized field of automotive service. Applicable for secondary or adult education, this guide describes: the brake system, types of brakes, diagnosis and correction of brake…

Integrated Baseline System (IBS) Version 2.0: Models guide

Energy Technology Data Exchange (ETDEWEB)

1994-03-01

The Integrated Baseline System (IBS) is an emergency management planning and analysis tool being developed under the direction of the US Army Nuclear and Chemical Agency. This Models Guide summarizes the IBS use of several computer models for predicting the results of emergency situations. These include models for predicting dispersion/doses of airborne contaminants, traffic evacuation, explosion effects, heat radiation from a fire, and siren sound transmission. The guide references additional technical documentation on the models when such documentation is available from other sources. The audience for this manual is chiefly emergency management planners and analysts, but also data managers and system managers.

Color Parameters of the Chromascop Shade Guide

Directory of Open Access Journals (Sweden)

William J. O'Brien

2012-12-01

Full Text Available The purposes of this study are: (1 determine the color of the twenty shades in the Ivoclar’s Chromascop shade guide, (2 determine the color representation of the shade guide described as coverage error (CE, and (3 compare this shade guide with the Vita Classical and Bioform shade guides. The spectral data was collected using Beckman model DU reflectance spectrophotometer equipped with an integrating sphere. Commission International de l’Eclairage (CIE chromaticity coordinates were calculated using CIE illuminant C and 1931 observer data, then converted to CIE L*a*b* and Munsell notation. Each shade was spectrophotometrically compared to the published colors of 335 human teeth. The minimum CIE L*a*b* color difference was calculated for each tooth and the average of these color differences was defined as the CE. The measured colors of the Chromascop guide had a CIE L* range of 79.67 to 65.61, an a* range of -0.71 to 3.85, and a b* range of 14.58 to 27.69. The average CE of the Chromascop shade guide was 3.38. The Chromascop shade guide has similar colors and a CE compared with the Bioform and Vita Classical shade guides, but with some shades of higher red and yellow components.

Project summary plan for HTGR recycle reference facility

International Nuclear Information System (INIS)

Baxter, B.J.

1979-11-01

A summary plan is introduced for completing conceptual definition of an HTGR Recycle Reference Facility (HRRF). The plan describes a generic project management concept, often referred to as the requirements approach to systems engineering. The plan begins with reference flow sheets and provides for the progressive evolution of HRRF requirements and definition through feasibility, preconceptual, and conceptual phases. The plan lays end-to-end all the important activities and elements to be treated during each phase of design. Identified activities and elements are further supported by technical guideline documents, which describe methodology, needed terminology, and where relevant a worked example

Does Guru Granth Sahib describe depression?

Science.gov (United States)

Kalra, Gurvinder; Bhui, Kamaldeep; Bhugra, Dinesh

2013-01-01

Sikhism is a relatively young religion, with Guru Granth Sahib as its key religious text. This text describes emotions in everyday life, such as happiness, sadness, anger, hatred, and also more serious mental health issues such as depression and psychosis. There are references to the causation of these emotional disturbances and also ways to get out of them. We studied both the Gurumukhi version and the English translation of the Guru Granth Sahib to understand what it had to say about depression, its henomenology, and religious prescriptions for recovery. We discuss these descriptions in this paper and understand its meaning within the context of clinical depression. Such knowledge is important as explicit descriptions about depression and sadness can help encourage culturally appropriate assessment and treatment, as well as promote public health through education.

Weather Test Reference Year of Greenland

DEFF Research Database (Denmark)

Kragh, Jesper; Pedersen, Frank; Svendsen, Svend

2005-01-01

the construction of two test reference years of Greenland used in the work of establishing new energy frame for the coming building code of Greenland. The first test reference year is constructed using measurements of climatic parameters from the town Nuuk located in the southwestern part of Greenland. The second...... test reference year is constructed using measurements from the town Uummannaq located in the north part of Greenland on the west coast. The construction of the test reference years fulfills the procedures described in the standard EN ISO 15927-4 using the following main weather parameters: Dry bulb...... temperature, global radiation, relative humidity and mean wind speed. To construct the test reference years a program called REFYEAR was developed in MatLab. REFYEAR automatically constructs the test reference year using an input file containing the climatic measurements. The two constructed test reference...

LAPACK users` guide: Release 1.0

Energy Technology Data Exchange (ETDEWEB)

Anderson, E.; Bai, Z.; Bischof, C.; Demmel, J.; Dongarra, J.; Du Croz, J.; Greenbaum, A.; Hammarling, S.; McKenney, A.; Ostrouchov, S.; Sorensen, D.

1992-01-31

LAPACK is a transportable library of Fortran 77 subroutines for solving the most common problems in numerical linear algebra: systems of linear equations, linear least squares problems, eigenvalue problems and singular value problems. LAPACK is designed to supersede LINPACK and EISPACK, principally by restructuring the software to achieve much greater efficiency on vector processors, high-performance ``superscalar`` workstations, and shared-memory multi-processors. LAPACK also adds extra functionality, uses some new or improved algorithms, and integrates the two sets of algorithms into a unified package. The LAPACK Users` Guide gives an informal introduction to the design of the algorithms and software, summarizes the contents of the package, describes conventions used in the software and documentation, and includes complete specifications for calling the routines. This edition of the Users` guide describes Release 1.0 of LAPACK.

PFP functional development planning guide

International Nuclear Information System (INIS)

SINCLAIR, J.C.

1999-01-01

The PFP Functional Development Planning Guide presents the strategy and process used for the identification, development, and analysis of functions (activities) necessary to satisfy the requirements within the Plutonium Finishing Plant (PFP) integrated project baseline. The functional analysis will provide the basis for the development of a function driven work breakdown structure. Future revisions to this document will include as attachments the results of the PFP Functional Analysis resulting from this approach. This document is intended be a Project-owned management tool. As such, the guide will periodically require revisions resulting from improvements of the information, processes, and techniques as now described

Guided interventions in musculoskeletal ultrasound: what's the evidence?

International Nuclear Information System (INIS)

Davidson, J.; Jayaraman, S.

2011-01-01

Increasing histological and radiological understanding of the processes involved in soft-tissue injury is leading to novel targeted treatments. A number of reviews have recommended that these treatments should be performed with image guidance. This review describes current ultrasound-guided interventions and injections, together with the level of evidence for these. Discussion of guided interventions will include; percutaneous lavage (barbotage), brisement, dry needling, electrocoagulation, and of guided injections; corticosteroids, autologous substances (blood and platelet rich plasma), sclerosants, and prolotherapy (hyperosmolar dextrose). Representative imaging illustrating some of these techniques is included for correlation with the methods described. As these procedures are often performed in sportspeople, it is essential that the radiologist is aware of prohibited substances and methods outlined in an annual publication from the World Anti-Doping Association (WADA). Finally, future directions, including the use of autologous substances, mesenchymal and stem cells will be discussed.

Nuclear measurements and reference materials

International Nuclear Information System (INIS)

1988-01-01

This report summarizes the progress of the JRC programs on nuclear data, nuclear metrology, nuclear reference materials and non-nuclear reference materials. Budget restrictions and personnel difficulties were encountered during 1987. Fission properties of 235 U as a function of neutron energy and of the resonances can be successfully described on the basis of a three exit channel fission model. Double differential neutron emission cross-sections were accomplished on 7 Li and were started for the tritium production cross-section of 9 Be. Reference materials of uranium minerals and ores were prepared. Special nuclear targets were prepared. A batch of 250 g of Pu0 2 was characterized in view of certification as reference material for the elemental assay of plutonium

Writing More Informative Letters of Reference

OpenAIRE

Wright, Scott M; Ziegelstein, Roy C

2004-01-01

Writing a meaningful and valuable letter of reference is not an easy task. Several factors influence the quality of any letter of reference. First, the accuracy and reliability of the writer's impressions and judgment depend on how well he knows the individual being described. Second, the writer's frame of reference, which is determined by the number of persons at the same level that he has worked with, will impact the context and significance of his beliefs and estimations. Third, the letter...

Surface multipole guide field for plasma injection

International Nuclear Information System (INIS)

Breun, R.A.; Rael, B.H.; Wong, A.Y.

1977-01-01

Described here is a surface guide field system which is useful for injection of plasmas into confinement devices. Experimental results are given for 5--25-eV hydrogen plasmas produced by a coaxial discharge (Marshall) gun. It is found that better than 90% of the plasma produced by the gun is delivered to the end of the guide 180 cm away, while the neutral component falls by more than an order of magnitude. For these results the rod current providing the magnetic field had to be large enough to provide at least 1.5-ion gyroradii from the center of the guide to the surface of the inner rod

Alternative Energy: A Guide to Free Information for Educators.

Science.gov (United States)

White, Janet A.

This guide was compiled to help teachers and students locate free educational materials (both lessons and nontechnical background references) on renewable energy resources and energy conservation. The 214 entries are arranged by these topic areas: (1) energy efficiency and renewables; (2) biomass; (3) hydropower; (4) solar thermal energy; (5)…

Guide to Spoken-Word Recordings: Popular Literature. Reference Circular No. 95-01.

Science.gov (United States)

Library of Congress, Washington, DC. National Library Service for the Blind and Physically Handicapped.

This reference circular contains selected sources for the purchase, rental, or loan of fiction and nonfiction spoken-word recordings. The sources in sections 1, 2, and 3 are commercial and, unless otherwise noted, offer abridged and unabridged titles on audio cassette. Sources in section 1 make available popular fiction; classics; poetry; drama;…

Guide to good practices for developing learning objectives. DOE Handbook

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-07-01

This guide to good practices provides information and guidance on the types of and development of learning objectives in a systematic approach to training program. This document can serve as a reference during the development of new learning objectives or refinement of existing ones.

Tornadoes: Nature's Most Violent Storms. A Preparedness Guide Including Safety Information for Schools.

Science.gov (United States)

American National Red Cross, Washington, DC.

This preparedness guide explains and describes tornadoes, and includes safety information for schools. A tornado is defined as a violently rotating column of air extending from a thunderstorm to the ground. The guide explains the cause of tornadoes, provides diagrams of how they form, describes variations of tornadoes, and classifies tornadoes by…

Weather integration in TMC operations : a self-evaluation and planning guide.

Science.gov (United States)

2009-04-01

This flyer describes how Traffic Management Centers (TMC) can integrate weather information into their daily operations, and is based on the Road Weather Management Program publication, Self-Evaluation and Planning Guide (FHWA-JPO-08-057). The Guide ...

Reference Tools for Data Processing, Office Automation, and Data Communications: An Introductory Guide.

Science.gov (United States)

Cupoli, Patricia Dymkar

1981-01-01

Provides an introduction to various reference sources which are useful in dealing with the areas of data processing, office automation, and communications technologies. A bibliography with vendor listings is included. (FM)

Terminal attack trajectories of peregrine falcons are described by the proportional navigation guidance law of missiles.

Science.gov (United States)

Brighton, Caroline H; Thomas, Adrian L R; Taylor, Graham K

2017-12-19

The ability to intercept uncooperative targets is key to many diverse flight behaviors, from courtship to predation. Previous research has looked for simple geometric rules describing the attack trajectories of animals, but the underlying feedback laws have remained obscure. Here, we use GPS loggers and onboard video cameras to study peregrine falcons, Falco peregrinus , attacking stationary targets, maneuvering targets, and live prey. We show that the terminal attack trajectories of peregrines are not described by any simple geometric rule as previously claimed, and instead use system identification techniques to fit a phenomenological model of the dynamical system generating the observed trajectories. We find that these trajectories are best-and exceedingly well-modeled by the proportional navigation (PN) guidance law used by most guided missiles. Under this guidance law, turning is commanded at a rate proportional to the angular rate of the line-of-sight between the attacker and its target, with a constant of proportionality (i.e., feedback gain) called the navigation constant ( N ). Whereas most guided missiles use navigation constants falling on the interval 3 ≤ N ≤ 5, peregrine attack trajectories are best fitted by lower navigation constants (median N law could find use in small visually guided drones designed to remove other drones from protected airspace. Copyright © 2017 the Author(s). Published by PNAS.

Reference materials for molecular diagnostics: Current achievements and future strategies.

Science.gov (United States)

Jing, Rongrong; Wang, Huimin; Ju, Shaoqing; Cui, Ming

2018-06-01

Molecular diagnoses have become more widespread in many areas of laboratory medicine where qualitative or quantitative approaches are used to detect nucleic acids. The increasing number of assay methods and the targets for molecular diagnostics contribute to variability in the test results among clinical laboratories. Thus, reference materials (RMs) are required to enhance the comparability of results. This review focuses on the definition of RMs as well as the production and characteristics of higher order RMs from different organizations and their future strategies. We describe the recent progress in RMs, including the definition of RMs by the Joint Committee for Guides in Metrology, as well as the production and characteristics of higher order RMs by international official bodies. There is an urgent need for RMs in nucleic acid testing, especially higher order RMs. To advance the harmonization and standardization of clinical nucleic acid detection, cooperation between the above organizations is proposed and different approaches to higher order RMs development are also needed. Copyright © 2018 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

A Meta-Analysis of Typhoid Diagnostic Accuracy Studies: A Recommendation to Adopt a Standardized Composite Reference.

Directory of Open Access Journals (Sweden)

Helen L Storey

Full Text Available Novel typhoid diagnostics currently under development have the potential to improve clinical care, surveillance, and the disease burden estimates that support vaccine introduction. Blood culture is most often used as the reference method to evaluate the accuracy of new typhoid tests; however, it is recognized to be an imperfect gold standard. If no single gold standard test exists, use of a composite reference standard (CRS can improve estimation of diagnostic accuracy. Numerous studies have used a CRS to evaluate new typhoid diagnostics; however, there is no consensus on an appropriate CRS. In order to evaluate existing tests for use as a reference test or inclusion in a CRS, we performed a systematic review of the typhoid literature to include all index/reference test combinations observed. We described the landscape of comparisons performed, showed results of a meta-analysis on the accuracy of the more common combinations, and evaluated sources of variability based on study quality. This wide-ranging meta-analysis suggests that no single test has sufficiently good performance but some existing diagnostics may be useful as part of a CRS. Additionally, based on findings from the meta-analysis and a constructed numerical example demonstrating the use of CRS, we proposed necessary criteria and potential components of a typhoid CRS to guide future recommendations. Agreement and adoption by all investigators of a standardized CRS is requisite, and would improve comparison of new diagnostics across independent studies, leading to the identification of a better reference test and improved confidence in prevalence estimates.

Ultrasound-guided biopsy of transplanted pancreas: evaluation of 20 cases

Directory of Open Access Journals (Sweden)

Marcel Vieira da Nóbrega

2009-03-01

Full Text Available Objective: To report the experience with percutaneous biopsies of pancreatic grafts guided by ultrasonography. Methods: Series of cases referred from outpatient’s clinic for biopsy of pancreas transplant, between December 2006 and March 2008. Data were collected from medical electronic records for age, sex and histopathology. The indication for the procedure was obtained from medical and laboratory records. Doppler ultrasonography was performed for control and to guide biopsy in real time. Rresults: Twenty patients referred for biopsy of their transplanted pancreas over a one-year period were evaluated. In one patient, biopsy was not performed for having no safe access for ultrasound. It was used 18 gauge needles, mostly automatic-cut type. The main indications were increased blood glucose and pancreatic enzyme levels as well as reduction of urinary amylase. The sonographic aspect of the pancreatic graft was normal in 18 cases. In all 19 biopsies performed, satisfactory samples for histopathological study were obtained. There were no complications. Cconclusions: This series of cases demonstrated low sensitivity and specificity of ultrasound in diagnosis of pancreatic transplants disorders, but showed to be very useful to guide transplanted pancreas biopsies. Although no complications occurred in this experience, the risk-benefit relation should always be assessed for every patient.

IEA Implementing Agreements and Annexes: A Guide for Building Technologies Program Managers

Energy Technology Data Exchange (ETDEWEB)

Evans, Meredydd; Meier, Alan; Runci, Paul J.

2008-08-05

This guide presents insights and guidance from DOE’s gathered through longstanding and extensive participation in IEA implementing agreements (IAs) and annexes. Even though DOE has been a key participant in international research activities through the IEA since the 1970s, the experience, knowledge, and institutional memory associated with these activities can be lost or forgotten easily as key DOE managers retire or leave the department. The guide seeks to assemble in a single reference some of the learning that has occurred through participation in IEA IAs as a guide for BTP managers currently responsible for IAs and for those who might consider entering into new IEA activities in the future.

Standard guide for use of UV-A and visible light sources and meters used in the liquid penetrant and magnetic particle methods

CERN Document Server

American Society for Testing and Materials. Philadelphia

2004-01-01

1.1 This guide describes the use of UV-A/Visible light sources and meters used for the examination of materials by the liquid penetrant and magnetic particle processes. This guide may be used to help support the needs for appropriate light intensities and light measurement. 1.2 This guide also provides a reference: 1.2.1 To assist in the selection of light sources and meters that meet the applicable specifications or standards. 1.2.2 For use in the preparation of internal documentation dealing with liquid penetrant or magnetic particle examination of materials and parts. 1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and det...

Colour in flux: describing and printing colour in art

Science.gov (United States)

Parraman, Carinna

2008-01-01

This presentation will describe artists, practitioners and scientists, who were interested in developing a deeper psychological, emotional and practical understanding of the human visual system who were working with wavelength, paint and other materials. From a selection of prints at The Prints and Drawings Department at Tate London, the presentation will refer to artists who were motivated by issues relating to how colour pigment was mixed and printed, to interrogate and explain colour perception and colour science, and in art, how artists have used colour to challenge the viewer and how a viewer might describe their experience of colour. The title Colour in Flux refers, not only to the perceptual effect of the juxtaposition of one colour pigment with another, but also to the changes and challenges for the print industry. In the light of screenprinted examples from the 60s and 70s, the presentation will discuss 21 st century ideas on colour and how these notions have informed the Centre for Fine Print Research's (CFPR) practical research in colour printing. The latter part of this presentation will discuss the implications for the need to change methods in mixing inks that moves away from existing colour spaces, from non intuitive colour mixing to bespoke ink sets, colour mixing approaches and colour mixing methods that are not reliant on RGB or CMYK.

75 FR 5351 - Proposed Revisions to Accounting Guide for LSC Recipients

Science.gov (United States)

2010-02-02

... LEGAL SERVICES CORPORATION Proposed Revisions to Accounting Guide for LSC Recipients AGENCY: Legal Services Corporation. ACTION: Notice and Request for Comments. SUMMARY: The Legal Services Corporation... banking transactions; (2) financial oversight concepts from the Sarbanes Oxley Act of 2002; (3) references...

Laser guide stars for optical free-space communications

Science.gov (United States)

Mata-Calvo, Ramon; Bonaccini Calia, Domenico; Barrios, Ricardo; Centrone, Mauro; Giggenbach, Dirk; Lombardi, Gianluca; Becker, Peter; Zayer, Igor

2017-02-01

The German Aerospace Center (DLR) and the European Southern Observatory (ESO) performed a measurement campaign together in April and July 2016 at Teide-Observatory (Tenerife), with the support of the European Space Agency (ESA), to investigate the use of laser guide stars (LGS) in ground to space optical communications. Atmospheric turbulence causes strong signal fluctuations in the uplink, due to scintillation and beam wander. In space communications, the use of the downlink channel as reference for pointing and for pre-distortion adaptive optics is limited by the size of the isokinetic and isoplanatic angle in relation to the required point-ahead angle. Pointing and phase errors due to the decorrelation between downward and upward beam due to the point-ahead angle may have a severe impact on the required transmit power and the stability of the communications link. LGSs provide a self-tailored reference to any optical ground-to-space link, independently of turbulence conditions and required point-ahead angle. In photon-starved links, typically in deep-space scenarios, LGSs allow dedicating all downlink received signal to communications purposes, increasing the available link margin. The scope of the joint DLR-ESO measurement campaign was, first, to measure the absolute value of the beam wander (uplink-tilt) using a LGS, taking a natural star as a reference, and, second, to characterize the decrease of correlation between uplink-tilt and downlink-tilt with respect to the angular separation between both sources. This paper describes the experiments performed during the measurement campaigns, providing an overview of the measured data and the first outcomes of the data post-processing.

PINS Spectrum Identification Guide

Energy Technology Data Exchange (ETDEWEB)

A.J. Caffrey

2012-03-01

The Portable Isotopic Neutron Spectroscopy—PINS, for short—system identifies the chemicals inside munitions and containers without opening them, a decided safety advantage if the fill chemical is a hazardous substance like a chemical warfare agent or an explosive. The PINS Spectrum Identification Guide is intended as a reference for technical professionals responsible for the interpretation of PINS gamma-ray spectra. The guide is divided into two parts. The three chapters that constitute Part I cover the science and technology of PINS. Neutron activation analysis is the focus of Chapter 1. Chapter 2 explores PINS hardware, software, and related operational issues. Gamma-ray spectral analysis basics are introduced in Chapter 3. The six chapters of Part II cover the identification of PINS spectra in detail. Like the PINS decision tree logic, these chapters are organized by chemical element: phosphorus-based chemicals, chlorine-based chemicals, etc. These descriptions of hazardous, toxic, and/or explosive chemicals conclude with a chapter on the identification of the inert chemicals, e.g. sand, used to fill practice munitions.

An Economist’s Guide to Digital Music

OpenAIRE

Martin Peitz; Patrick Waelbroeck

2004-01-01

In this guide, we discuss the impact of digitalization on the music industry. We rely on market and survey data at the international level as well as expert statements from the industry. The guide investigates recent developments in legal and technological protection of digital music and describes new business models as well as consumers' attitude towards music downloads and audio-streaming. We conclude the guide by a discussion of the evolution of the music industry.

A methodology guide for the retrofit of rubbish dump sites; Guide methodologique pour la remise en etat des decharges d`ordures menageres et assimiles

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-10-01

This guide, developed by the French Agency for Environment and Energy Conservation, is aimed for local communities and gives information on impacts and constraints due to municipal waste disposal and sites, and ways to retrofit a dumping site: nuisances, present and future risks related to pollution, safety and hygiene are presented, together with the various types of wastes, responsibilities and legislations related to these issues; the guide also gives information on diagnosis, audit study and retrofitting methodologies, considering the risks and rehabilitation opportunities. Reference and document models (composition and evolution of liquid and gaseous effluents, inquiry forms, diagnosis study,...) are also presented

Emerging solutions in reference services implications for libraries in the new millennium

CERN Document Server

Edwards, John D

2013-01-01

How can you enhance reference services without adding staff?Modern law librarians are under growing pressure to keep up with new technologies, deal instantly with the demands of patrons, keep the library safe and user-friendly, and generally offer the best possible service while keeping costs down. Emerging Solutions in Reference Services: Implications for Libraries in the New Millennium is a very practical guide for coping with rapidly changing technology and increasing demands for services. Its sane, well-researched advice and suggestions can help you deal with the hectic days and

User's guide to the western spruce budworm modeling system

Science.gov (United States)

Nicholas L. Crookston; J. J. Colbert; Paul W. Thomas; Katharine A. Sheehan; William P. Kemp

1990-01-01

The Budworm Modeling System is a set of four computer programs: The Budworm Dynamics Model, the Prognosis-Budworm Dynamics Model, the Prognosis-Budworm Damage Model, and the Parallel Processing-Budworm Dynamics Model. Input to the first three programs and the output produced are described in this guide. A guide to the fourth program will be published separately....

Magnetic-resonance-guided biopsy of focal liver lesions

Energy Technology Data Exchange (ETDEWEB)

Smith, Ethan A. [University of Michigan Health System, Section of Pediatric Radiology, C.S. Mott Children' s Hospital, Department of Radiology, Ann Arbor, MI (United States); Grove, Jason J. [University of Michigan Health System, Division of Interventional Radiology, C.S. Mott Children' s Hospital, Department of Radiology, Ann Arbor, MI (United States); Der Spek, Abraham F.L.V. [University of Michigan Health System, Department of Anesthesiology, C.S. Mott Children' s Hospital, Ann Arbor, MI (United States); Jarboe, Marcus D. [University of Michigan Health System, Division of Interventional Radiology, C.S. Mott Children' s Hospital, Department of Radiology, Ann Arbor, MI (United States); University of Michigan Health System, Section of Pediatric Surgery, C.S. Mott Children' s Hospital, Department of Surgery, Ann Arbor, MI (United States)

2017-05-15

Image-guided biopsy techniques are widely used in clinical practice. Commonly used methods employ either ultrasound (US) or computed tomography (CT) for image guidance. In certain patients, US or CT guidance may be suboptimal, or even impossible, because of artifacts, suboptimal lesion visualization, or both. We recently began performing magnetic resonance (MR)-guided biopsy of focal liver lesions in select pediatric patients with lesions that are not well visualized by US or CT. This report describes our experience performing MR-guided biopsy of focal liver lesions, with case examples to illustrate innovative techniques and novel aspects of these procedures. (orig.)

The Environmental Restoration Project Style and Resources Guide; TOPICAL

International Nuclear Information System (INIS)

C. J. Forbes

1999-01-01

This Style Guide identifies the wide and flexible array of support services/resources that are available to ER project and functional organizations through Publication and Graphic Services. The Style Guide describes how ER Project groups can complete virtually any kind of information project without any costs charged to their budgets. Another purpose of the Style Guide is to provide ER project and functional organizations with the ability to determine when to request capabilities/resources for information projects, and when to complete such projects on their own

Good Practice Guide: Bringing a Social Capital Approach into the Teaching of Adult Literacy and Numeracy

Science.gov (United States)

National Centre for Vocational Education Research (NCVER), 2010

2010-01-01

This good practice guide is based on research that looked at how to teach adult literacy and numeracy using a social capital approach. The guide suggests ways vocational education and training (VET) practitioners can adopt a social capital approach to their teaching practice. A social capital approach refers to the process in which networks are…

Brazilian readers and contextual reference Brazilian readers and contextual reference

Directory of Open Access Journals (Sweden)

Lilia M. O. Carioni

2008-04-01

Full Text Available This article describes an experiment carried out using Brazilian university students at UFSC, the purpose being to check comprehension relationships between two types of contextual reference and two languages, Portuguese and English. A major stimulus for the research was the question: are Brazilian students' difficulties in reading English related more to English language difficulties or to difficulties in processing text in general?

A guide to the management of tailings facilities

International Nuclear Information System (INIS)

Bedard, C.; Ferguson, K.; Gladwin, D.; Lang, D.; Maltby, J.; McCann, M.; Poirier, P.; Schwenger, R.; Vezina, S.; West, S.; Duval, J.; Gardiner, E.; Jansons, K.; Lewis, B.; Matthews, J.; Mchaina, D.; Puro, M.; Siwik, R.; Welch, D.

1998-01-01

The 'Guide to the Management of Tailings Facilities' has been developed by the Mining Association of Canada in an effort to provide guidance to its member companies on sound practices for the safe and environmentally responsible management of tailings facilities. The guide is a reference tool to help companies ensure that they are managing their tailings facilities responsibly, integrating environmental and safety considerations in a consistent manner, with continuous improvement in the operation of tailings facilities. The key to managing tailings responsibly is consistent application of engineering capabilities through the full life cycle. The guide provides a basis for the development of customized tailings management systems to address specific needs at individual operations, and deals with environmental impacts, mill tailing characteristics, tailings facility studies and plans, dam and related structure design, and control and monitoring. Aspects relating to tailings facility siting, design, construction, operation, decommissioning and closure are also fully treated. 1 tab., 3 figs

Recent Development in Ultrasonic Guided Waves for Aircraft and Composite Materials

International Nuclear Information System (INIS)

Rose, Joseph L.

2009-01-01

Emphasis in the paper is placed on describing guided wave successes and challenges for applications in aircraft and composite materials inspection. Guided wave imaging methods discussed includes line of sight, tomography, guided wave C-scan, phased array, and ultrasonic vibration methods. Applications outlined encircles lap splice, bonded repair patch, fuselage corrosion, water loaded structures, delamination, and ice detection and de-icing of various structures.

Outline of examination guides of water-cooled research reactors in Japan

International Nuclear Information System (INIS)

Yoshino, F.; Kimura, R.

1992-01-01

The Nuclear Safety Commission of Japan published two examination guides of water-cooled research reactors on July 18, 1991; one is for safety design, and another is for safety evaluation. In these guides, careful consideration is taken into account on the basic safety characteristic features of research reactors in order to be reasonable regulative requirements. This paper describes the fundamental philosophy and outline of the guides. (author)

Reference Japanese man

International Nuclear Information System (INIS)

Tanaka, Giichiro

1985-01-01

To make real and accurate dose assessment method so far, it is necessitated to provide ''Reference Japanese Man'' based on anotomical, physiological and biochemical data of Japanese people instead of the Reference Man presented in ICRP Publications 23 and 30. This review describes present status of researched for the purpose of establishing of Reference Japanese Man. The Reference Japanese Man is defined as a male or female adult who lives in Japan with a Japanese life-style and food custom. His stature and body weight, and the other data was decided as mean values of male or female people of Japan. As for food custom, Japanese people take significantly smaller amount of meat and milk products than Western people, while larger intake amount of cereals and marine products such as fish or seaweeds. Weight of organs is a principal factor for internal dose assessment and mean values for living Japanese adult has been investigated and the value employable for dose assessment for organs and tissues are shown. To employ these values of Reference Japanese Man, it should be taken into account of age. Metabolic parameters should also be considered. Iodine metabolism in Japanese is quite different from that of Western people. The above-mentioned data are now tentatively employing in modification of table of MIRD method and others. (Takagi, S.)

QUAGOL: a guide for qualitative data analysis.

Science.gov (United States)

Dierckx de Casterlé, Bernadette; Gastmans, Chris; Bryon, Els; Denier, Yvonne

2012-03-01

Data analysis is a complex and contested part of the qualitative research process, which has received limited theoretical attention. Researchers are often in need of useful instructions or guidelines on how to analyze the mass of qualitative data, but face the lack of clear guidance for using particular analytic methods. The aim of this paper is to propose and discuss the Qualitative Analysis Guide of Leuven (QUAGOL), a guide that was developed in order to be able to truly capture the rich insights of qualitative interview data. The article describes six major problems researchers are often struggling with during the process of qualitative data analysis. Consequently, the QUAGOL is proposed as a guide to facilitate the process of analysis. Challenges emerged and lessons learned from own extensive experiences with qualitative data analysis within the Grounded Theory Approach, as well as from those of other researchers (as described in the literature), were discussed and recommendations were presented. Strengths and pitfalls of the proposed method were discussed in detail. The Qualitative Analysis Guide of Leuven (QUAGOL) offers a comprehensive method to guide the process of qualitative data analysis. The process consists of two parts, each consisting of five stages. The method is systematic but not rigid. It is characterized by iterative processes of digging deeper, constantly moving between the various stages of the process. As such, it aims to stimulate the researcher's intuition and creativity as optimal as possible. The QUAGOL guide is a theory and practice-based guide that supports and facilitates the process of analysis of qualitative interview data. Although the method can facilitate the process of analysis, it cannot guarantee automatic quality. The skills of the researcher and the quality of the research team remain the most crucial components of a successful process of analysis. Additionally, the importance of constantly moving between the various stages

Guide to the economic regulation of the electricity industry

International Nuclear Information System (INIS)

1999-06-01

Guide to the Economic Regulation of the Electricity Industry, part of the series of OXERA Guides to Regulation, is designed as an essential work of reference for those who work in regulation and for practitioners who need to understand the needs and mechanics of regulation. The 154-page document provides: comprehensive coverage of the institutional and legal framework which defines the regulation of the electricity industry; an examination of current regulatory issues and developments in the industry; explanations of the roles of the key players; a condensed account of all the relevant legal documents; coverage of the industry in Scotland and Northern Ireland. (Author)

A Citizen's Guide to Vapor Intrusion Mitigation

Science.gov (United States)

This guide describes how vapor intrusion is the movement of chemical vapors from contaminated soil and groundwater into nearby buildings.Vapors primarily enter through openings in the building foundation or basement walls.

Guide to the safety design examination about light water reactor facilities for power generation

International Nuclear Information System (INIS)

Anon.

1977-01-01

This guide was compiled to evaluate the validity of the design policy when the safety design is examined at the time of the application for approval of the installation of nuclear reactors. About 7 years has elapsed since the existing guide was established, and the more appropriate guide to evaluate the safety should be made on the basis of the knowledge and experience accumulated thereafter. The range of application of this guide is limited to the above described evaluation, and it is not intended as the general standard for the design of nuclear reactors. First, the definition of the words used in this guide is given. Then, the guide to the safety examination is described about the general matters of reactor facilities, nuclear reactors and the measuring and controlling system, reactor-stopping system, reactivity-controlling system and safety protection system, reactor-cooling system, reactor containment vessels, fuel handling and waste treatment system. Several matters which require attention in the application of this guide or the clarification of the significance and interpretation of the guide itself were found, therefore the explanation about them was added at the end of this guide. (Kako, I.)

Referent Salience Affects Second Language Article Use

Science.gov (United States)

Trenkic, Danijela; Pongpairoj, Nattama

2013-01-01

The effect of referent salience on second language (L2) article production in real time was explored. Thai (-articles) and French (+articles) learners of English described dynamic events involving two referents, one visually cued to be more salient at the point of utterance formulation. Definiteness marking was made communicatively redundant with…

Building America Best Practices Series Volume 11. Builders Challenge Guide to 40% Whole-House Energy Savings in the Marine Climate

Energy Technology Data Exchange (ETDEWEB)

Baechler, Michael C.; Gilbride, Theresa L.; Hefty, Marye G.; Cole, Pamala C.; Williamson, Jennifer L.; Love, Pat M.

2010-09-01

This best practices guide is the eleventh in a series of guides for builders produced by the U.S. Department of Energy’s Building America Program. This guide book is a resource to help builders design and construct homes that are among the most energy-efficient available, while addressing issues such as building durability, indoor air quality, and occupant health, safety, and comfort. With the measures described in this guide, builders in the marine climate (portions of Washington, Oregon, and California) can achieve homes that have whole house energy savings of 40% over the Building America benchmark (a home built to mid-1990s building practices roughly equivalent to the 1993 Model Energy Code) with no added overall costs for consumers. These best practices are based on the results of research and demonstration projects conducted by Building America’s research teams. The guide includes information for managers, designers, marketers, site supervisors, and subcontractors, as well as case studies of builders who are successfully building homes that cut energy use by 40% in the marine climate. This document is available on the web at www.buildingamerica.gov. This report was originally cleared 06-29-2010. This version is Rev 1 cleared in Nov 2010. The only change is the reference to the Energy Star Windows critieria shown on pg 8.25 was updated to match the criteria - Version 5.0, 04/07/2009, effective 01/04/2010.

Certification of a new biological reference material - Virginia Tobacco Leaves (CTA-VTL-2) and homogeneity study by NAA on this and other candidate reference materials

International Nuclear Information System (INIS)

Dybczynski, Rajmund; Polkowska-Motrenko, Halina; Samczynski, Zbigniew; Szopa, Zygmunt; Kulisa, Krzysztof; Wasek, Marek

2002-01-01

This report describes the laboratory's participation in the interlaboratory comparison run where the laboratory applied neutron activation analysis aimed at certification of the candidate reference material. Data evaluation and statistical treatment steps are discussed. The report also describes homogeneity study on the reference material and provides details of the analytical procedures

La puissance prescriptive des guides à Paris The prescriptive power of tour guides in Paris. Standardizing elements of tourism ?

Directory of Open Access Journals (Sweden)

Gwendal Simon

2008-10-01

Full Text Available Les « guide-interprètes » constituent des médiateurs entre les touristes et les espaces. Incarnant une présence physique en mesure d’aider les touristes en les informant sur la ville, ils opèrent comme prescripteurs de choses à voir et à faire. S’ils officient très diversement selon les touristes qu’ils accompagnent, ils exercent toujours leur pratique dans une logique de production de discours sur la ville. À Paris, la dimension muséale et patrimoniale constitue depuis longtemps le socle de l’attractivité touristique, qui continue de capitaliser sur des imaginaires et des pratiques liés à la grande ville d’Art et d’Histoire. Face à la constitution de ce référentiel dominant qui opère comme une force d’ « imposition », les guide-interprètes tentent néanmoins de décentrer le regard par des prescriptions délestées des symboles. C’est cette « tension » entre cet ensemble de références touristiques « à voir » et le souci de montrer la ville dans sa pluralité que nous analysons. Ces éléments nourrissent la réflexion actuelle sur les formes polarisées du tourisme à Paris et l’importance de la production de référents urbains plus contemporains que promeut la municipalité.Tour guides are mediators between tourists and spaces. As they embody a physical presence helping tourists and informing them about the city, they also act as prescribers, laying down what is supposed to be seen and to be done. If their recommendations depend on the tourists they travel with, they always mean to produce a discourse on the city. Paris’ museums and heritage have long since been two cornerstones of her enduring appeal. Confronted with this phenomenon, which tends to standardize the way of visiting a city, tour guides try to free their guidelines of symbolic references. This contribution focuses on the tension between must-see tourist references and the desire to show the city in all its diversity. These

Making the library accessible for all a practical guide for librarians

CERN Document Server

Vincent, Jane

2014-01-01

Accessibility is becoming an issue that libraries can no longer ignore. Making the Library Accessible for All provides a holistic guide to accessibility that addresses common issues and gives strategies for responding to unique situations. This book is a single-source guide relevant to all library functions that librarians can easily refer to when planning, remediating, or evaluating for accessibility. It has a unique holistic perspective, as well as an emphasis on perceiving people with disabilities as providing resources to meet a common goal rather than as a population to be "served."

Return on investment (ROI) proposal preparation guide

International Nuclear Information System (INIS)

Valero, O.J.

1998-01-01

The ROI Proposal Preparation Guide is a tool to assist Hanford waste generators in preparing ROI proposal forms for submittal to Department of Energy, Richland Operations Office (DOE/RL) for funding. The guide describes the requirements for submitting an ROI proposal and provides examples of completed ROI forms. The intent is to assist waste generators in identifying projects that meet the criteria, provide information necessary to complete the ROI forms, and submit a proposal that is eligible to receive funding

Threshold-driven optimization for reference-based auto-planning

Science.gov (United States)

Long, Troy; Chen, Mingli; Jiang, Steve; Lu, Weiguo

2018-02-01

We study threshold-driven optimization methodology for automatically generating a treatment plan that is motivated by a reference DVH for IMRT treatment planning. We present a framework for threshold-driven optimization for reference-based auto-planning (TORA). Commonly used voxel-based quadratic penalties have two components for penalizing under- and over-dosing of voxels: a reference dose threshold and associated penalty weight. Conventional manual- and auto-planning using such a function involves iteratively updating the preference weights while keeping the thresholds constant, an unintuitive and often inconsistent method for planning toward some reference DVH. However, driving a dose distribution by threshold values instead of preference weights can achieve similar plans with less computational effort. The proposed methodology spatially assigns reference DVH information to threshold values, and iteratively improves the quality of that assignment. The methodology effectively handles both sub-optimal and infeasible DVHs. TORA was applied to a prostate case and a liver case as a proof-of-concept. Reference DVHs were generated using a conventional voxel-based objective, then altered to be either infeasible or easy-to-achieve. TORA was able to closely recreate reference DVHs in 5-15 iterations of solving a simple convex sub-problem. TORA has the potential to be effective for auto-planning based on reference DVHs. As dose prediction and knowledge-based planning becomes more prevalent in the clinical setting, incorporating such data into the treatment planning model in a clear, efficient way will be crucial for automated planning. A threshold-focused objective tuning should be explored over conventional methods of updating preference weights for DVH-guided treatment planning.

Requirements for data integration platforms in biomedical research networks: a reference model.

Science.gov (United States)

Ganzinger, Matthias; Knaup, Petra

2015-01-01

Biomedical research networks need to integrate research data among their members and with external partners. To support such data sharing activities, an adequate information technology infrastructure is necessary. To facilitate the establishment of such an infrastructure, we developed a reference model for the requirements. The reference model consists of five reference goals and 15 reference requirements. Using the Unified Modeling Language, the goals and requirements are set into relation to each other. In addition, all goals and requirements are described textually in tables. This reference model can be used by research networks as a basis for a resource efficient acquisition of their project specific requirements. Furthermore, a concrete instance of the reference model is described for a research network on liver cancer. The reference model is transferred into a requirements model of the specific network. Based on this concrete requirements model, a service-oriented information technology architecture is derived and also described in this paper.

Reference in human and non-human primate communication: What does it take to refer?

Science.gov (United States)

Sievers, Christine; Gruber, Thibaud

2016-07-01

The concept of functional reference has been used to isolate potentially referential vocal signals in animal communication. However, its relatedness to the phenomenon of reference in human language has recently been brought into question. While some researchers have suggested abandoning the concept of functional reference altogether, others advocate a revision of its definition to include contextual cues that play a role in signal production and perception. Empirical and theoretical work on functional reference has also put much emphasis on how the receiver understands the referential signal. However, reference, as defined in the linguistic literature, is an action of the producer, and therefore, any definition describing reference in non-human animals must also focus on the producer. To successfully determine whether a signal is used to refer, we suggest an approach from the field of pragmatics, taking a closer look at specific situations of signal production, specifically at the factors that influence the production of a signal by an individual. We define the concept of signaller's reference to identify intentional acts of reference produced by a signaller independently of the communicative modality, and illustrate it with a case study of the hoo vocalizations produced by wild chimpanzees during travel. This novel framework introduces an intentional approach to referentiality. It may therefore permit a closer comparison of human and non-human animal referential behaviour and underlying cognitive processes, allowing us to identify what may have emerged solely in the human lineage.

Hanford Tanks Initiative requirements and document management process guide

International Nuclear Information System (INIS)

Schaus, P.S.

1998-01-01

This revision of the guide provides updated references to project management level Program Management and Assessment Configuration Management activities, and provides working level directions for submitting requirements and project documentation related to the Hanford Tanks Initiative (HTI) project. This includes documents and information created by HTI, as well as non-HTI generated materials submitted to the project

A quick guide to pipeline engineering

CERN Document Server

Alkazraji, D

2008-01-01

Pipeline engineering requires an understanding of a wide range of topics. Operators must take into account numerous pipeline codes and standards, calculation approaches, and reference materials in order to make accurate and informed decisions.A Quick Guide to Pipeline Engineering provides concise, easy-to-use, and accessible information on onshore and offshore pipeline engineering. Topics covered include: design; construction; testing; operation and maintenance; and decommissioning.Basic principles are discussed and clear guidance on regulations is provided, in a way that will

An Annotated Guide to Audio-Visual Materials for Teaching Shakespeare.

Science.gov (United States)

Albert, Richard N.

Audio-visual materials, found in a variety of periodicals, catalogs, and reference works, are listed in this guide to expedite the process of finding appropriate classroom materials for a study of William Shakespeare in the classroom. Separate listings of films, filmstrips, and recordings are provided, with subdivisions for "The Plays"…

Numerical prediction for effects of guide vane blade numbers on hydraulic turbine performance

International Nuclear Information System (INIS)

Shi, F X; Yang, J H; Wang, X H; Li, C E

2013-01-01

Using unstructured hybrid grid technique and SIMPLEC algorithm,a general three-dimensional simulation based on Reynolds Navier- stocks in multiple reference frames and the RNG k-ε turbulence model, is presented for the reversal centrifugal pump (PAT) with a guide vane. Four different schemes are designed by a change of the number of guide vane blade of PAT. The inner flow field in every scheme is simulated, accordingly, the external characteristic and static pressure distribution in flow field in PAT is obtained. The results obtained show that the efficiency can be improved by adding a guide vane for the PAT, besides, the high efficiency area is wider than before. Guide blade numbers changed, external characteristics of turbine changed, and the external characteristic changed. The optimal value is existent for the guide vane blade number, which has a great impact on the distribution of pressure in runner inlet

IRMM-1000a and IRMM-1000b. Uranium reference materials certified for the production date based on the 230Th/234U radiochronometer. Part II. Certification

International Nuclear Information System (INIS)

Venchiarutti, C.; Richter, S.; Jakopic, R.; Aregbe, Y.; Varga, Z.; Nicholl, A.; Krajko, J.; Mayer, K.

2016-01-01

The IRMM-1000a and IRMM-1000b uranium reference materials, of 20 and 50 mg uranium, respectively, were produced by the European Commission Joint Research Centre's Institute for Reference Materials and Measurements (EC-JRC-IRMM) in collaboration with the Institute for Transuranium Elements (EC-JRC-ITU). They are novel uranium reference materials certified for the production date based on the 230 Th/ 234 U radiochronometer, i.e. the date of the last chemical separation of these two radionuclides. The certified reference value and its uncertainty, homogeneity and stability of the material were established in accordance with the ISO Guide 34:2009 and the 'Guide to the Expression of Uncertainty in Measurement'. (author)

User's guide to the biosphere code BIOMOD

International Nuclear Information System (INIS)

Kane, P.

1983-05-01

BIOMOD has been designed to interface with SYVAC, the function of which is to perform generic risk assessments on hypothetical repository-geosphere-biosphere combinations. The user's guide contains the detailed specifications for the models used, a description of the interim user-interface, a specification for required input and definition of output. Sources of error are indicated and reference is made to the database description and other documents issued relating to BIOMOD. (author)

Uncertainty analysis guide

International Nuclear Information System (INIS)

Andres, T.H.

2002-05-01

This guide applies to the estimation of uncertainty in quantities calculated by scientific, analysis and design computer programs that fall within the scope of AECL's software quality assurance (SQA) manual. The guide weaves together rational approaches from the SQA manual and three other diverse sources: (a) the CSAU (Code Scaling, Applicability, and Uncertainty) evaluation methodology; (b) the ISO Guide,for the Expression of Uncertainty in Measurement; and (c) the SVA (Systems Variability Analysis) method of risk analysis. This report describes the manner by which random and systematic uncertainties in calculated quantities can be estimated and expressed. Random uncertainty in model output can be attributed to uncertainties of inputs. The propagation of these uncertainties through a computer model can be represented in a variety of ways, including exact calculations, series approximations and Monte Carlo methods. Systematic uncertainties emerge from the development of the computer model itself, through simplifications and conservatisms, for example. These must be estimated and combined with random uncertainties to determine the combined uncertainty in a model output. This report also addresses the method by which uncertainties should be employed in code validation, in order to determine whether experiments and simulations agree, and whether or not a code satisfies the required tolerance for its application. (author)

Uncertainty analysis guide

Energy Technology Data Exchange (ETDEWEB)

Andres, T.H

2002-05-01

This guide applies to the estimation of uncertainty in quantities calculated by scientific, analysis and design computer programs that fall within the scope of AECL's software quality assurance (SQA) manual. The guide weaves together rational approaches from the SQA manual and three other diverse sources: (a) the CSAU (Code Scaling, Applicability, and Uncertainty) evaluation methodology; (b) the ISO Guide,for the Expression of Uncertainty in Measurement; and (c) the SVA (Systems Variability Analysis) method of risk analysis. This report describes the manner by which random and systematic uncertainties in calculated quantities can be estimated and expressed. Random uncertainty in model output can be attributed to uncertainties of inputs. The propagation of these uncertainties through a computer model can be represented in a variety of ways, including exact calculations, series approximations and Monte Carlo methods. Systematic uncertainties emerge from the development of the computer model itself, through simplifications and conservatisms, for example. These must be estimated and combined with random uncertainties to determine the combined uncertainty in a model output. This report also addresses the method by which uncertainties should be employed in code validation, in order to determine whether experiments and simulations agree, and whether or not a code satisfies the required tolerance for its application. (author)

Modifying the Heysham 2 and Torness guide tubes

International Nuclear Information System (INIS)

Salter, I.D.

1988-01-01

In 1986 the National Nuclear Corporation carried out the unfuelled engineering run on Torness Reactor One. Subsequent inspection revealed wear on the reactor control rods, following severe spinning caused by gas cross flow swirls at the guide tube castellated ring. The adopted solution was to machine 32 radial holes through the guide tube wall and blank off the existing castellated slots, however, man access to the guide tubes is extremely difficult. This paper describes how Taylor Hitec produced, in only 12 weeks, three remote drilling machines, together with associated debris collection systems, cleaning equipment and remote video/CCTV inspection systems, and then carried out the modifications to the reactors. (author)

User's guide to the Sandia Mathematical Program Library at Livermore

Energy Technology Data Exchange (ETDEWEB)

Huddleston, R.E.; Jefferson, T.H.

1976-03-01

The Sandia Mathematical Program Library is a collection of general-purpose mathematical subroutines which are maintained within Sandia on a quick service basis. This document is intended to be a reference guide for using the library at Sandia Laboratories, Livermore. (auth)

NCEP BUFRLIB Software User Guide

Science.gov (United States)

Integration Branch > Decoders > BUFRLIB BUFRLIB Software User Guide This document set describes how to use the NCEP BUFRLIB software to encode or decode BUFR messages. It is not intended to be a primer on background knowledge of the basic concepts of BUFR and will focus solely on how to use the BUFRLIB software

Peer-Led Guided in Calculus at University of South Florida

Science.gov (United States)

Bénéteau, Catherine; Fox, Gordon; Xu, Xiaoying; Lewis, Jennifer E.; Ramachandran, Kandethody; Campbell, Scott; Holcomb, John

2016-01-01

This paper describes the development of a Peer-Led Guided Inquiry (PLGI) program for teaching calculus at the University of South Florida. This approach uses the POGIL (Process Oriented Guided Inquiry Learning) teaching strategy and the small group learning model PLTL (Peer-Led Team Learning). The developed materials used a learning cycle based on…

PEGASUS User's Guide. 5.1c

Science.gov (United States)

Suhs, Norman E.; Dietz, William E.; Rogers, Stuart E.; Nash, Steven M.; Onufer, Jeffrey T.

2000-01-01

PEGASUS 5.1 is the latest version of the PEGASUS series of mesh interpolation codes. It is a fully three-dimensional code. The main purpose for the development of this latest version was to significantly decrease the number of user inputs required and to allow for easier operation of the code. This guide is to be used with the user's manual for version 4 of PEGASUS. A basic description of methods used in both versions is described in the Version 4 manual. A complete list of all user inputs used in version 5.1 is given in this guide.

Elaboration and modification of the waste zoning plan in basic nuclear installations. ASN Guide Nr 23, Release of the 2016/08/30

International Nuclear Information System (INIS)

2016-01-01

After having recalled the relevant regulatory texts and guides, this guide aims at detailing conditions of elaboration and of modification of the waste zoning plan which is defined in one of these texts, and applies requirements and recommendations of others of them. It first recalls the general doctrine of waste management in basic nuclear installations. It describes how the waste zoning plan and the reference waste zoning map are elaborated and justified, how the relevancy of this plan and this map are confirmed through radiological controls and based on general operation rules and periodic assessments. It also describes how contamination transfers and material activation are prevented, and discusses waste radiological controls to be performed. The next part addressed waste zoning and ways of management for wastes coming from conventional waste areas, and from areas of possible production of nuclear wastes. Issues of waste zoning downgrading or reclassification are then addressed by distinguishing temporary and definitive modifications (in one way or the other). Some peculiar cases are addressed: delimitation of waste zoning at the level of equipments, conventional processing of some wastes, radioactive waste warehousing, outdoor areas of possible production of nuclear wastes

Reference Design Project Book: NUSEL-Homestake

OpenAIRE

Haxton, W. C.

2003-01-01

This submission includes the overview, science timeline, reference design, WBS, and mine status sections of the Homestake collaboration's Reference Design Project Book. The Project Book describes the specific plan for converting the Homestake Gold Mine into a facility for physics, earth science, and engineering. The proposed developments on the 7400- and 4850-ft levels are presented, along with the plans for adapting Homestake's existing infrastructure for science. The plan differs substantia...

Hanford Ground-Water Data Base management guide

International Nuclear Information System (INIS)

Rieger, J.T.; Mitchell, P.J.; Muffett, D.M.; Fruland, R.M.; Moore, S.B.; Marshall, S.M.

1990-02-01

This guide describes the Hanford Ground-Water Data Base (HGWDB), a computerized data base used to store hydraulic head, sample analytical, temperature, geologic, and well-structure information for ground-water monitoring wells on the Hanford Site. These data are stored for the purpose of data retrieval for report generation and also for historical purposes. This guide is intended as an aid to the data base manager and the various staff authorized to enter and verify data, maintain the data base, and maintain the supporting software. This guide focuses on the structure of the HGWDB, providing a fairly detailed description of the programs, files, and parameters. Data-retrieval instructions for the general user of the HGWDB will be found in the HGWDB User's Manual. 6 figs

Writing more informative letters of reference.

Science.gov (United States)

Wright, Scott M; Ziegelstein, Roy C

2004-05-01

Writing a meaningful and valuable letter of reference is not an easy task. Several factors influence the quality of any letter of reference. First, the accuracy and reliability of the writer's impressions and judgment depend on how well he knows the individual being described. Second, the writer's frame of reference, which is determined by the number of persons at the same level that he has worked with, will impact the context and significance of his beliefs and estimations. Third, the letter-writing skills of the person composing the letter will naturally affect the letter. To support the other components of a candidate's application, a letter of reference should provide specific examples of how an individual's behavior or attitude compares to a reference group and should assess "intangibles" that are hard to glean from a curriculum vitae or from test scores. This report offers suggestions that should help physicians write more informative letters of reference.

Atlas-guided prostate intensity modulated radiation therapy (IMRT) planning

International Nuclear Information System (INIS)

Sheng, Yang; Li, Taoran; Zhang, You; Lee, W Robert; Yin, Fang-Fang; Wu, Q Jackie; Ge, Yaorong

2015-01-01

An atlas-based IMRT planning technique for prostate cancer was developed and evaluated. A multi-dose atlas was built based on the anatomy patterns of the patients, more specifically, the percent distance to the prostate and the concaveness angle formed by the seminal vesicles relative to the anterior-posterior axis. A 70-case dataset was classified using a k-medoids clustering analysis to recognize anatomy pattern variations in the dataset. The best classification, defined by the number of classes or medoids, was determined by the largest value of the average silhouette width. Reference plans from each class formed a multi-dose atlas. The atlas-guided planning (AGP) technique started with matching the new case anatomy pattern to one of the reference cases in the atlas; then a deformable registration between the atlas and new case anatomies transferred the dose from the atlas to the new case to guide inverse planning with full automation. 20 additional clinical cases were re-planned to evaluate the AGP technique. Dosimetric properties between AGP and clinical plans were evaluated. The classification analysis determined that the 5-case atlas would best represent anatomy patterns for the patient cohort. AGP took approximately 1 min on average (corresponding to 70 iterations of optimization) for all cases. When dosimetric parameters were compared, the differences between AGP and clinical plans were less than 3.5%, albeit some statistical significances observed: homogeneity index (p  >  0.05), conformity index (p  <  0.01), bladder gEUD (p  <  0.01), and rectum gEUD (p  =  0.02). Atlas-guided treatment planning is feasible and efficient. Atlas predicted dose can effectively guide the optimizer to achieve plan quality comparable to that of clinical plans. (paper)

Automated tru-cut imaging-guided core needle biopsy of canine ...

African Journals Online (AJOL)

The purpose of this study was to evaluate the diagnostic value of imaging-guided core needle biopsy for canine orbital mass diagnosis. A second excisional biopsy obtained during surgery or necropsy was used as the reference standard. A prospective feasibility study was conducted in 23 canine orbital masses at a single ...

The art of appropriate evaluation : a guide for highway safety program managers

Science.gov (United States)

2008-08-01

The guide, updated from its original release in 1999, is intended for project managers who will oversee the evaluation of traffic safety programs. It describes the benefits of evaluation and provides an overview of the steps involved. The guide inclu...

COATING ALTERNATIVES GUIDE (CAGE) USER'S GUIDE

Science.gov (United States)

The guide provides instructions for using the Coating Alternatives GuidE (CAGE) software program, version 1.0. It assumes that the user is familiar with the fundamentals of operating an IBM-compatible personal computer (PC) under the Microsoft disk operating system (MS-DOS). CAGE...

Why patients self-refer to the Emergency Department: A qualitative interview study.

Science.gov (United States)

Kraaijvanger, Nicole; Rijpsma, Douwe; Willink, Lisa; Lucassen, Peter; van Leeuwen, Henk; Edwards, Michael

2017-06-01

There have been multiple studies investigating reasons for patients to self-refer to the Emergency Department (ED). The majority made use of questionnaires and excluded patients with urgent conditions. The goal of this qualitative study is to explore what motives patients have to self-refer to an ED, also including patients in urgent triage categories. In a large teaching hospital in the Netherlands, a qualitative interview study focusing on reasons for self-referring to the ED was performed. Self-referred patients were included until no new reasons for attending the ED were found. Exclusion criteria were as follows: not mentally able to be interviewed or not speaking Dutch. Patients who were in need of urgent care were treated first, before being asked to participate. Interviews followed a predefined topic guide. Practicing cyclic analysis, the interview topic guide was modified during the inclusion period. Interviews were recorded on an audio recorder, transcribed verbatim, and anonymized. Two investigators independently coded the information and combined the codes into meaningful clusters. Subsequently, these were categorized into themes to build a framework of reasons for self-referral to the ED. Characteristic quotes were used to illustrate the acquired theoretical framework. Thirty self-referred patients were interviewed. Most of the participants were male (63%), with a mean age of 46 years. Two main themes emerged from the interviews that are pertinent to the patients' decisions to attend the ED: (1) health concerns and (2) practical issues. This study found that there are 2 clearly distinctive reasons for self-referral to the ED: health concerns or practical motives. Self-referral because of practical motives is probably most suitable for strategies that aim to reduce inappropriate ED visits. © 2016 John Wiley & Sons, Ltd.

Control rod guide tube assembly

International Nuclear Information System (INIS)

Jabsen, F.S.

1982-01-01

An improved fuel assembly is described as consisting of a sleeve that engages one end of a control rod guide tube essentially fixing the guide tube to one of the fuel assembly end structures. The end of the sleeve protrudes above the surface of the end fitting. The outer surface of the sleeve has a peripheral groove that engages the resilient sides of a cellular grid or lattice shaped lock. This lock fixes the sleeve in position between the various elements that comprise the end fitting, thereby eliminating a profusion of costly and potentially troublesome nuts, threaded studs and the like that are frequently employed in the fuel assemblies that are presently in use

Constraining neutron guide optimizations with phase-space considerations

Energy Technology Data Exchange (ETDEWEB)

Bertelsen, Mads, E-mail: mads.bertelsen@gmail.com; Lefmann, Kim

2016-09-11

We introduce a method named the Minimalist Principle that serves to reduce the parameter space for neutron guide optimization when the required beam divergence is limited. The reduced parameter space will restrict the optimization to guides with a minimal neutron intake that are still theoretically able to deliver the maximal possible performance. The geometrical constraints are derived using phase-space propagation from moderator to guide and from guide to sample, while assuming that the optimized guides will achieve perfect transport of the limited neutron intake. Guide systems optimized using these constraints are shown to provide performance close to guides optimized without any constraints, however the divergence received at the sample is limited to the desired interval, even when the neutron transport is not limited by the supermirrors used in the guide. As the constraints strongly limit the parameter space for the optimizer, two control parameters are introduced that can be used to adjust the selected subspace, effectively balancing between maximizing neutron transport and avoiding background from unnecessary neutrons. One parameter is needed to describe the expected focusing abilities of the guide to be optimized, going from perfectly focusing to no correlation between position and velocity. The second parameter controls neutron intake into the guide, so that one can select exactly how aggressively the background should be limited. We show examples of guides optimized using these constraints which demonstrates the higher signal to noise than conventional optimizations. Furthermore the parameter controlling neutron intake is explored which shows that the simulated optimal neutron intake is close to the analytically predicted, when assuming that the guide is dominated by multiple scattering events.

VOC-Arid Integrated Demonstration guide to preparation of demonstration documents

International Nuclear Information System (INIS)

Jensen, E.J.; Brouns, T.M.; Koegler, K.J.; McCabe, G.H.; Morris, F.A.

1994-06-01

This guide has been prepared by Demonstration Operations of the Volatile Organic Compound-Arid Integrated Demonstration (VOC-Arid ID). Its purpose is to describe demonstration documents, designate responsibilities for these documents, and guide the Principal Investigator (PI) and others in their preparation. The main emphasis of this guide is to describe the documentation required of the PI. However, it does cover some of the responsibilities of other members of the VOC-Arid ID team. The VOC-Arid ID is one of several US Department of Energy (DOE) integrated demonstrations designed to support the demonstration of emerging environmental management and restoration technologies. The principal objective of the VOC-Arid ID is to identify, develop, and demonstrate new and innovative technologies for environmental restoration at arid or semiarid sites containing volatile organic compounds with or without associated contamination (e.g., radionuclides and metals)

Design of the Mechanical Parts for the Neutron Guide System at HANARO

International Nuclear Information System (INIS)

Shin, J. W.; Cho, Y. G.; Cho, S. J.; Ryu, J. S.

2008-01-01

The research reactor HANARO (High-flux Advanced Neutron Application ReactOr) in Korea will be equipped with a neutron guide system, in order to transport cold neutrons from the neutron source to the neutron scattering instruments in the neutron guide hall near the reactor building. The neutron guide system of HANARO consists of the in-pile plug assembly with in-pile guides, the primary shutter with in-shutter guides, the neutron guides in the guide shielding room with dedicated secondary shutters, and the neutron guides connected to the instruments in the neutron guide hall. Functions of the in-pile plug assembly are to shield the reactor environment from nuclear radiation and to support the neutron guides and maintain them precisely oriented. The primary shutter is a mechanical structure to be installed just after the in-pile plug assembly, which stops neutron flux on demand. This paper describes the design of the in-pile assembly and the primary shutter for the neutron guide system at HANARO. The design of the guide shielding assembly for the primary shutter and the neutron guides is also presented

Religious Studies: The Shaping of a Field and a Guide to Reference Resources.

Science.gov (United States)

Lippy, Charles H.

1992-01-01

Discusses the development of religious studies as an academic discipline. Examines the work of leading thinkers in the field, including anthropologists Sir James Fraser and Edward Burnett Taylor, sociologist Max Weber, and psychologist Erik Erikson. Identifies some of the many reference works that deal with religious studies. (SG)

Methodological guide: management of industrial sites potentially contaminated by radioactive substances

International Nuclear Information System (INIS)

2001-01-01

At the request of the Ministries of Health and the Environment, IPSN is preparing and publishing the first version of the methodological guide devoted to managing industrial sites potentially contaminated by radioactive substances. This guide describes a procedure for defining and choosing strategies for rehabilitating such industrial sites. (author)

Monte Carlo program for the cold neutron beam guide

International Nuclear Information System (INIS)

Yoshiki, H.

1985-02-01

A Monte Carlo program for the transport of cold neutrons through beam guides has been developed assuming that the neutrons follow the specular reflections. Cold neutron beam guides are normally used to transport cold neutrons (4 ∼ 10 Angstrom) to experimental equipments such as small angle scattering apparatus, TOF measuring devices, polarized neutron spectrometers, and ultra cold neutron generators, etc. The beam guide is about tens of meters in length and is composed from a meter long guide elements made up from four pieces of Ni coated rectangular optical glass. This report describes mathematics and algorithm employed in the Monte Carlo program together with the display of the results. The source program and input data listings are also attached. (Aoki, K.)

VERA 3.5 Installation Guide

Energy Technology Data Exchange (ETDEWEB)

Bartlett, Roscoe A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Baird, Mark L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Berrill, Mark A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Kulesza, Joel A. [Univ. of Michigan, Ann Arbor, MI (United States); Mervin, Brenden T. [Electric Power Research Inst. (EPRI), Charlotte, NC (United States)

2016-08-16

This guide describes the structure and setup of the standard VERA development environment (VERA Dev Env) and standard VERA Third Party Libraries (TPLs) that need to be in place before installing many of the VERA simulation components. It describes everything from the initial setup on a new machine to the final build, testing, and installation of VERA components. The goal of this document is to describe how to create the directories and contents outlined in Standard VERA Dev Env Directory Structure and then obtain the remaining VERA source and build, test, and install any of the necessary VERA components on a given system. This document describes the process both for a development version of VERA and for a released tarball of the VERA sources.

VERA 3.5 Installation Guide

International Nuclear Information System (INIS)

Bartlett, Roscoe A.; Baird, Mark L.; Berrill, Mark A.; Kulesza, Joel A.; Mervin, Brenden T.

2016-01-01

This guide describes the structure and setup of the standard VERA development environment (VERA Dev Env) and standard VERA Third Party Libraries (TPLs) that need to be in place before installing many of the VERA simulation components. It describes everything from the initial setup on a new machine to the final build, testing, and installation of VERA components. The goal of this document is to describe how to create the directories and contents outlined in Standard VERA Dev Env Directory Structure and then obtain the remaining VERA source and build, test, and install any of the necessary VERA components on a given system. This document describes the process both for a development version of VERA and for a released tarball of the VERA sources.

DOE handbook: Guide to good practices for training and qualification of chemical operators

International Nuclear Information System (INIS)

1996-03-01

The purpose of this Handbook is to provide contractor training organizations with information that can be used as a reference to refine existing chemical operator training programs, or develop new training programs where no program exists. This guide, used in conjunction with facility-specific job analyses, will provide a framework for training and qualification programs for chemical operators at DOE reactor and nonreactor facilities. Recommendations for qualification are made in four areas: education, experience, physical attributes, and training. Contents include: initial qualification; administrative training; industrial safety training; specialized skills training; on-the-job training; trainee evaluation; continuing training; training effectiveness evaluation; and program records. Two appendices describe Fundamentals training and Process operations. This handbook covers chemical operators in transportation of fuels and wastes, spent fuel receiving and storage, fuel disassembly, fuel reprocessing, and both liquid and solid low-level waste processing

Green electricity buyer's guide

International Nuclear Information System (INIS)

Kelly, B.; Klein, S.; Olivastri, B.

2002-06-01

The electricity produced in whole or in large part from renewable energy sources like wind, small hydro electricity and solar energy, is generally referred to as green electricity. The authors designed this buyer's guide to assist customers in their understanding of green electricity, as the customers can now choose their electricity supplier. The considerations and steps involved in the purchasse of green electricity are identified, and advice is provided on ways to maximize the benefits from the purchase of green electricity. In Alberta and Ontario, customers have access to a competitive electricity market. The emphasis when developing this guide was placed firmly on the large buyers, as they can have enormous positive influence on the new market for green electricity. The first chapter of the document provides general information on green electricity. In chapter two, the authors explore the opportunity for environmental leadership. Chapter three reviews the basics of green electricity, which provides the link to chapter four dealing with the creation of a policy. Purchasing green electricity is dealt with in Chapter five, and maximizing the benefits of green electricity are examined in Chapter Six. 24 refs., 3 tabs

Improving Physical Activity Resource Guides to Bridge the Divide Between the Clinic and the Community

OpenAIRE

Seligman, Hilary K.; Grossman, Melanie D.; Bera, Nathalie; Stewart, Anita L.

2008-01-01

Introduction Primary care providers have limited time for physical activity counseling. They can optimize counseling time by referring patients to community resources for more comprehensive support. To facilitate referrals, resource guides (lists of community opportunities with descriptive information) are often created but seldom used. We elicited the detailed opinions of providers about how to make resource guides more useful for them. Methods We asked a convenience sample of health care pr...

Operational limits and conditions and operating procedures for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2005-01-01

relation between the fundamental safety objective and the OLCs. The concept and development of OLCs are introduced in Section 3. Sections 4 to 7 describe in some detail the characteristics of the types of OLCs, safety limits, limits on safety system settings, limits and conditions for normal operation, and surveillance requirements. Sections 8 and 9 address the question of OPs, including their development. In Section 10 guidance is provided on how to ensure compliance with OLCs and procedures, including reference to the need to retain records of such compliance. Appendix 1 presents a sample list of the items for which limits and conditions are generally established and Appendix 11 gives outlines for the development of OPs. In the Annex an example is provided to explain some terms used in the Safety Guide. A Glossary is included at the end

Operational limits and conditions and operating procedures for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2000-01-01

relation between the fundamental safety objective and the OLCs. The concept and development of OLCs are introduced in Section 3. Sections 4 to 7 describe in some detail the characteristics of the types of OLCs, safety limits, limits on safety system settings, limits and conditions for normal operation, and surveillance requirements. Sections 8 and 9 address the question of OPs, including their development. In Section 10 guidance is provided on how to ensure compliance with OLCs and procedures, including reference to the need to retain records of such compliance. Appendix 1 presents a sample list of the items for which limits and conditions are generally established and Appendix 11 gives outlines for the development of OPs. In the Annex an example is provided to explain some terms used in the Safety Guide. A Glossary is included at the end

Smoke management photographic guide: a visual aid for communicating impacts

Science.gov (United States)

Joshua C. Hyde; Jarod Blades; Troy Hall; Roger D. Ottmar; Alistair. Smith

2016-01-01

Communicating emissions impacts to the public can sometimes be difficult because quantitatively conveying smoke concentrations is complicated. Regulators and land managers often refer to particulate-matter concentrations in micrograms per cubic meter, but this may not be intuitive or meaningful to everyone. The primary purpose of this guide is to serve as a tool for...

Windows Vista Administrator's Pocket Guide

CERN Document Server

Stanek, William R

2007-01-01

Portable and precise, this pocket-sized guide delivers immediate answers for the day-to-day administration of Windows Vista. Zero in on core support and maintenance tasks using quick-reference tables, instructions, and lists. You'll get the precise information you need to solve problems and get the job done-whether you're at your desk or in the field! Get fast facts to: Install and configure Windows Vista-and optimize the user workspaceMaintain operating system components, hardware devices, and driversCreate user and group accounts-and control rights and permissionsAdminister group policy se

Quantitative EPR A Practitioners Guide

CERN Document Server

Eaton, Gareth R; Barr, David P; Weber, Ralph T

2010-01-01

This is the first comprehensive yet practical guide for people who perform quantitative EPR measurements. No existing book provides this level of practical guidance to ensure the successful use of EPR. There is a growing need in both industrial and academic research to provide meaningful and accurate quantitative EPR results. This text discusses the various sample, instrument and software related aspects required for EPR quantitation. Specific topics include: choosing a reference standard, resonator considerations (Q, B1, Bm), power saturation characteristics, sample positioning, and finally, putting all the factors together to obtain an accurate spin concentration of a sample.

CCNA Cisco Certified Network Associate Study Guide

CERN Document Server

Lammle, Todd

2011-01-01

Learn from the Best - Cisco Networking Authority Todd LammleWritten by Cisco networking authority Todd Lammle, this comprehensive guide has been completely updated to reflect the latest CCNA 640-802 exam. Todd's straightforward style provides lively examples, hands on and written labs, easy-to-understand analogies, and real-world scenarios that will not only help you prepare for the exam, but also give you a solid foundation as a Cisco networking professional.This Study Guide teaches you how toDescribe how a network worksConfigure, verify and troubleshoot a switch with VLANs and interswitch co

Software and commands on VAX CERN. User's guide

International Nuclear Information System (INIS)

Balashov, V.K.; Trofimov, V.V.

1990-01-01

This guide describes a structure of applications software, which is available at VAX-type computers in JINR. The software includes program libraries, scientific programs and commands developed at CERN. 20 refs

Guiding young adults at risk

DEFF Research Database (Denmark)

Andreasen, Karen Egedal; Rasmussen, Palle Damkjær; Ydesen, Christian

2016-01-01

Karen Egedal Andreasen, Palle Rasmussen and Christian Ydesen question in their article, how to guide youth in danger of being marginalised or excluded from society in general and the labour market in particular. They analyse the guidance dimension in the youth in development project as described ...... significant persons and guidance about educational system and possible jobs....

LAPACK users' guide: Release 1. 0

Energy Technology Data Exchange (ETDEWEB)

Anderson, E.; Bai, Z.; Bischof, C.; Demmel, J.; Dongarra, J.; Du Croz, J.; Greenbaum, A.; Hammarling, S.; McKenney, A.; Ostrouchov, S.; Sorensen, D.

1992-01-31

LAPACK is a transportable library of Fortran 77 subroutines for solving the most common problems in numerical linear algebra: systems of linear equations, linear least squares problems, eigenvalue problems and singular value problems. LAPACK is designed to supersede LINPACK and EISPACK, principally by restructuring the software to achieve much greater efficiency on vector processors, high-performance superscalar'' workstations, and shared-memory multi-processors. LAPACK also adds extra functionality, uses some new or improved algorithms, and integrates the two sets of algorithms into a unified package. The LAPACK Users' Guide gives an informal introduction to the design of the algorithms and software, summarizes the contents of the package, describes conventions used in the software and documentation, and includes complete specifications for calling the routines. This edition of the Users' guide describes Release 1.0 of LAPACK.

10 CFR 63.305 - Required characteristics of the reference biosphere.

Science.gov (United States)

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Required characteristics of the reference biosphere. 63... Standards § 63.305 Required characteristics of the reference biosphere. (a) Features, events, and processes that describe the reference biosphere must be consistent with present knowledge of the conditions in...

The Chicago guide to communicating science

CERN Document Server

Montgomery, Scott L

2017-01-01

For more than a decade, The Chicago Guide to Communicating Science has been the go-to reference for anyone who needs to write or speak about their research. Whether a student writing a thesis, a faculty member composing a grant proposal, or a public information officer crafting a press release, Scott Montgomery’s advice is perfectly adaptable to any scientific writer’s needs. This new edition has been thoroughly revised to address crucial issues in the changing landscape of scientific communication, with an increased focus on those writers working in corporate settings, government, and nonprofit organizations as well as academia. Half a dozen new chapters tackle the evolving needs and paths of scientific writers. These sections address plagiarism and fraud, writing graduate theses, translating scientific material, communicating science to the public, and the increasing globalization of research. The Chicago Guide to Communicating Science recognizes that writers come to the table with different needs and...

29 CFR Appendix A to Subpart I of... - References for Further Information (Non-mandatory)

Science.gov (United States)

2010-07-01

... 29 Labor 5 2010-07-01 2010-07-01 false References for Further Information (Non-mandatory) A... Information (Non-mandatory) The documents in appendix A provide information which may be helpful in.... National Society to Prevent Blindness. “A Guide for Controlling Eye Injuries in Industry,” Chicago, Il...

Energy and environment design guide

Energy Technology Data Exchange (ETDEWEB)

Harman, K. [Royal Australian Institute of Architects, Canberra, ACT (Australia)

1996-04-01

The Royal Australian Institute of Architects (RAIA) released an Environment Policy for architects in September 1994 which forms part of the RAIA Code of Professional Conduct. Prior to releasing the policy, it was recognised that members needed information and education in the area of energy and environment in order to adopt and implement the guide. This document is a report on the scope, work programme and achievements of a project to provide an easy reference resource for architects and other building designers, and bring together a wide range of information and research. It includes the Environment Policy as an appendix. The project produced 24 notes entitled the `Environment Design Guide - energy/environment notes` covering a wide range of topics, and four newsletters. Feedback received from architects to date indicates that the development of the notes has had a positive effect on their knowledge of these issues, resulting in the making of informed design decisions. The topics covered by the notes are expected to expand in 1996 with the preparation of additional notes which provide information on products and sustainable construction.

Nuclear energy - Reference beta-particle radiation - Part 2: Calibration fundamentals related to basic quantities characterizing the radiation field

International Nuclear Information System (INIS)

2004-01-01

ISO 6980 consists of the following parts, under the general title Nuclear energy - Reference beta-particle radiation: Part 1: Method of production; Part 2: Calibration fundamentals related to basic quantities characterizing the radiation field; Part 3: Calibration of area and personal dosimeters and determination of their response as a function of energy and angle of incidence. This part 2 of ISO 6980 specifies methods for the measurement of the directional absorbed-dose rate in a tissue-equivalent slab phantom in the ISO 6980 reference beta-particle radiation fields. The energy range of the beta-particle-emitting isotopes covered by these reference radiations is 0.066 to 3.54 MeV (maximum energy). Radiation energies outside this range are beyond the scope of this standard. While measurements in a reference geometry (depth of 0.07 mm at perpendicular incidence in a tissue-equivalent slab phantom) with a reference class extrapolation chamber are dealt with in detail, the use of other measurement systems and measurements in other geometries are also described, although in less detail. The ambient dose equivalent, H*(10) as used for area monitoring of strongly penetrating radiation, is not an appropriate quantity for any beta radiation, even for that penetrating a 10 mm thick layer of ICRU tissue (i.e. E max > 2 MeV). If adequate protection is provided at 0.07 mm, only rarely will one be concerned with other depths, for example 3 mm. This document is geared towards organizations wishing to establish reference-class dosimetry capabilities for beta particles, and serves as a guide to the performance of dosimetry with the reference class extrapolation chamber for beta-particle dosimetry in other fields. Guidance is also provided on the statement of measurement uncertainties

Design of Instrumentation and Control Systems for Nuclear Power Plants. Specific Safety Guide

International Nuclear Information System (INIS)

2016-01-01

This publication is a revision and combination of two Safety Guides, IAEA Safety Standards Series No. NS-G-1.1 and No. NS-G-1.3. The revision takes into account developments in instrumentation and control (I&C) systems since the publication of the earlier Safety Guides. The main changes relate to the continuing development of computer applications and the evolution of the methods necessary for their safe, secure and practical use. In addition, account is taken of developments in human factors engineering and the need for computer security. This Safety Guide references and takes into account other IAEA Safety Standards and Nuclear Security Series publications that provide guidance relating to I&C design

Discussion of Regulatory Guide 7.10, emphasizing the graded approach for establishing QA programs

International Nuclear Information System (INIS)

Gordon, L.; Lake, W.H.

1983-01-01

To assist applicants in establishing an acceptable QA program to meet the programmatic elements of Appendix E to 10 CFR Part 71, Regulatory Guide 7.10 was developed. Regulatory Guide 7.10 is organized in three self-contained ANNEXES. Guidance applicable to designer/fabricators, to users, and users of radiographic devices are in separate annexes. QA programs for packaging to transport radioactive material are similar in regard to the various operations a licensee may be involved in. However, the appropriate QA/QC effort to verify the program elements may vary significantly. This is referred to as the graded approach. Appendix A in the guide addresses the graded approach

[The National Reference Centres and Reference Laboratories. Importance and tasks].

Science.gov (United States)

Laude, G; Ammon, A

2005-09-01

Since 1995, the German Federal Ministry for Health and Social Security funds National Reference Centres (NRC) for the laboratory surveillance of important pathogens and syndromes. Which pathogens or syndromes are selected to be covered by a NRC depends on their epidemiological relevance, the special diagnostic tools, problems with antimicrobial resistance and necessary infection control measures. Currently, there are 15 NRC, which are appointed for a period of 3 years (currently from January 2005 through December 2007). Towards the end of their appointment all NRC are evaluated by a group of specialists. The assessment of their achievements is guided by a catalogue of tasks for the NRC. In addition to the NRC, a total of 50 laboratories are appointed which provide specialist expertise for additional pathogens in order to have a broad range of pathogens for which specialist laboratories are available. Their predominant task is to give advice and support for special diagnostic problems. Both NRC and the specialist laboratories are important parts of the network for infectious disease epidemiology.

The generation and management of references with the Online Mechanism for References - MORE

Directory of Open Access Journals (Sweden)

Proxério Manoel Felisberto

2015-04-01

Full Text Available The scientific production and the development of academic papers have their own formalities. In this paper, is sought seek from these formalities for the ones that refers to the way of granting merits to the authors of the works used in the theoretical basis, through quotations and references. The goal is to help users of libraries to generate and manage references using a web tool developed for this purpose. There are many applications, in desktop and web platforms, that could be used to do this task. However, some of them require the payment of an expensive license to be fully functional. Others offers free versions, but they are very limited and often do not generate references specified by ABNT. There are others that do not store the generate references for later use. In order to fill this gap, the Online Mechanism for References (MORE was developed and made available to the general public in the web. Even so, the fast technological advances combined with a high number of users demanded an update to the application, done recently. It is important to state that all the work was developed exclusively with proven and free to use technologies. Initially, sought up identified the main tools available to generate and manage references and which free technologies could be used to build interactive web applications. This paper briefly describes the reengineering process that MORE was submitted, its new structure, new requirements met and its expanded portfolio of features. Finally, the results achieved after the reengineering are compared to indicators of its previous version.

Library Subject Guides: A Case Study of Evidence-Informed Library Development

Science.gov (United States)

Wakeham, Maurice; Roberts, Angharad; Shelley, Jane; Wells, Paul

2012-01-01

This paper describes the process whereby a university library investigated the value of its subject guides to its users. A literature review and surveys of library staff, library users and other libraries were carried out. Existing library subject guides and those of other higher education libraries were evaluated. The project team reported…

Monitoring of Defects in a Pipe Weld by a Comparison of Magnetostrictive Guided Wave Signals

International Nuclear Information System (INIS)

Cheong, Yong-Moo; Oh, Se-Beom; Lee, Duck-Hyun

2016-01-01

In this study a computer program for an accurate comparison and subtraction of guided wave signals were developed. The program contains an algorithm for calibration with the flight time and phases of ultrasonic signals in the time domain. Once the reference signals were acquired at the beginning of the monitoring, the signals can be compared to the reference. The signals due to the geometry can be eliminated clearly and an evolution of defect in a pipe can be monitored accurately. In order to improve the detectability and solve the problems of the guided wave methods, a magnetostrictive guided wave sensor technique was proposed. Because the waveforms by the magnetostrictive sensors are quite clear and repeatable, it is possible to detect the defects at the weld regions or even monitor the small variations of the defects after a permanent installation of the magnetostrictive strip sensors. In order to eliminate the signals from the geometry, such as weld, pipe support, branch connection, a computer algorithm and program were developed. A notch with 1.5% of CSA of the pipe can be detected with increased accuracy. The guided wave monitoring technique developed in this study can be a promising tool for inspection of the pipe with limited accessibility, such as insulated or buried pipe

Monitoring of Defects in a Pipe Weld by a Comparison of Magnetostrictive Guided Wave Signals

Energy Technology Data Exchange (ETDEWEB)

Cheong, Yong-Moo; Oh, Se-Beom; Lee, Duck-Hyun [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

In this study a computer program for an accurate comparison and subtraction of guided wave signals were developed. The program contains an algorithm for calibration with the flight time and phases of ultrasonic signals in the time domain. Once the reference signals were acquired at the beginning of the monitoring, the signals can be compared to the reference. The signals due to the geometry can be eliminated clearly and an evolution of defect in a pipe can be monitored accurately. In order to improve the detectability and solve the problems of the guided wave methods, a magnetostrictive guided wave sensor technique was proposed. Because the waveforms by the magnetostrictive sensors are quite clear and repeatable, it is possible to detect the defects at the weld regions or even monitor the small variations of the defects after a permanent installation of the magnetostrictive strip sensors. In order to eliminate the signals from the geometry, such as weld, pipe support, branch connection, a computer algorithm and program were developed. A notch with 1.5% of CSA of the pipe can be detected with increased accuracy. The guided wave monitoring technique developed in this study can be a promising tool for inspection of the pipe with limited accessibility, such as insulated or buried pipe.

Guide: Monitoring Programme for unannounced inspections undertaken against the National Standards for the Prevention and Control of Healthcare Associated Infections

OpenAIRE

2014-01-01

This is a guide to the Health Information and Quality Authority?s (the Authority) programme of monitoring service providers? compliance with the National Standards for the Prevention and Control of Healthcare Associated Infections (referred to in this guide as the Infection, Prevention and Control Standards). This guide explains the approach that the Authority takes when monitoring the compliance of service providers ? including hospitals ? with the Infection, Prevention and Control Standards...

Guide tube insert assembly for use in a nuclear reactor

International Nuclear Information System (INIS)

Hopkins, R.J.; Land, J.T.

1992-01-01

This patent describes an internals assembly for a nuclear reactor of the type including an upper support plate and an upper core plate, each having apertures for conducting control rod assemblies into an out of fuel assemblies with the apertures of the upper support plate being aligned with the apertures of the upper core plate, a guide tube insert assembly comprising: an elongated tubular body extending between at least one of the aligned apertures formed in the upper support plate and the upper core plate; guide plates within the elongated tubular body, each of the guide plates having a planar surface extending substantially perpendicular to an axial direction of the tubular body; at least one interconnecting means for interconnecting the guide plates into a guide tube insert assembly such that the guide plates are simultaneously mountable within and removable from the elongated body, and the periphery of each of the guide plates is spaced apart from the inner walls of the elongated tubular body at every point when the insert assembly is mounted within the tubular body, and a stabilizing means for securing the lowermost guide plate of the guide tube insert assembly within the elongated tubular body to prevent rotational and lateral movement between the guide tube insert assembly and the tubular body

System and Method for Measuring the Transfer Function of a Guided Wave Device

Science.gov (United States)

Froggatt, Mark E. (Inventor); Erdogan, Turan (Inventor)

2002-01-01

A method/system are provided for measuring the NxN scalar transfer function elements for an N-port guided wave device. Optical energy of a selected wavelength is generated at a source and directed along N reference optical paths having N reference path lengths. Each reference optical path terminates in one of N detectors such that N reference signals are produced at the N detectors. The reference signals are indicative of amplitude, phase and frequency of the optical energy carried along the N reference optical paths. The optical energy from the source is also directed to the N-ports of the guided wave device and then on to each of the N detectors such that N measurement optical paths are defined between the source and each of the N detectors. A portion of the optical energy is modified in terms of at least one of the amplitude and phase to produce N modified signals at each of the N detectors. At each of the N detectors, each of the N modified signals is combined with a corresponding one of the N reference signals to produce corresponding N combined signals at each of the N detectors. A total of N(sup 2) measurement signals are generated by the N detectors. Each of the N(sup 2) measurement signals is sampled at a wave number increment (Delta)k so that N(sup 2) sampled signals are produced. The NxN transfer function elements are generated using the N(sup 2) sampled signals. Reference and measurement path length constraints are defined such that the N combined signals at each of the N detectors are spatially separated from one another in the time domain.

Guide to good practices for developing learning objectives. DOE guideline

Energy Technology Data Exchange (ETDEWEB)

1992-07-01

This guide to good practices provides information and guidance on the types of, and the development of learning objectives in performance-based training system at reactor and nonreactor nuclear facilities. Contractors are encouraged to consider this guidance as a reference when developing new learning objectives or refining existing ones. Training managers, designers, developers, and instructors are the intended audiences.

Service design based on ITIL V3 a management guide

CERN Document Server

Bon, Jan van; Kolthof, Axel

2010-01-01

This Management Guide is a concise summary of the IT Service Management ? An Introduction. A quick, portable reference tool to the standards used within the Service Management community.What are the key service management processes? What is the ?lifecycle? approach?What are the elements of ISO20000? All this and descriptions of other popular frameworks are covered.

GUIDE TO CLEANER TECHNOLOGIES: ORGANIC COATING REPLACEMENTS

Science.gov (United States)

This guide describes available and emerging cleaner technologies that can be used to reduce emissions and wastes from paint and coatings applications. Environmental concerns and increasing costs of organic chemicals and metals are leading to changes in the formulation of organic ...

Guided interventions in musculoskeletal ultrasound: what's the evidence?

Energy Technology Data Exchange (ETDEWEB)

Davidson, J., E-mail: jdavidson@doctors.org.u [St Richard' s Hospital, Spitalfield Lane, Chichester, West Sussex (United Kingdom); Jayaraman, S. [St Richard' s Hospital, Spitalfield Lane, Chichester, West Sussex (United Kingdom)

2011-02-15

Increasing histological and radiological understanding of the processes involved in soft-tissue injury is leading to novel targeted treatments. A number of reviews have recommended that these treatments should be performed with image guidance. This review describes current ultrasound-guided interventions and injections, together with the level of evidence for these. Discussion of guided interventions will include; percutaneous lavage (barbotage), brisement, dry needling, electrocoagulation, and of guided injections; corticosteroids, autologous substances (blood and platelet rich plasma), sclerosants, and prolotherapy (hyperosmolar dextrose). Representative imaging illustrating some of these techniques is included for correlation with the methods described. As these procedures are often performed in sportspeople, it is essential that the radiologist is aware of prohibited substances and methods outlined in an annual publication from the World Anti-Doping Association (WADA). Finally, future directions, including the use of autologous substances, mesenchymal and stem cells will be discussed.

Nuclear Structure References (NSR) file

International Nuclear Information System (INIS)

Ewbank, W.B.

1978-08-01

The use of the Nuclear Structure References file by the Nuclear Data Project at ORNL is described. Much of the report concerns format information of interest only to those preparing input to the system or otherwise needing detailed knowledge of its internal structure. 17 figures

Practical guide to content delivery networks

CERN Document Server

Held, Gilbert

2005-01-01

With a practical and organized approach to learning and implementation, A Practical Guide to Content Delivery Networks presents a step-by-step process for building a highly available and highly scalable content delivery network (CDN). CDN refers to the infrastructure behind any service that provides utility or access to data to an end user. This book offers terminology, tactics, potential problems to avoid, and individual layers of design, providing clear understanding of the framework for CDNs using a structural and visual approach. The text emphasizes a best-of-breed strategy, allowing a tec

CT-guided puncture for direct MR-arthrography of the shoulder: Description of possible techniques

Directory of Open Access Journals (Sweden)

Hauth E

2016-07-01

Full Text Available The following report describes the possible techniques of CT-guided puncture for direct magnetic resonance (MR arthrography of the shoulder. CT-guided puncture can be regarded as an alternative technique to fluoroscopic- or ultrasound-guided puncture for MR-arthrography of the shoulder with high efficiency, low dose and extremely low complication rate.

The guide to sustainable energy technologies for schools; Un guide pour les technologies energetiques durables dans les ecoles

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

There are significant attractions for municipalities to opt for sustainable solutions which involve energy efficient technologies and measures. This is the challenging background which led to the production the Guide to Sustainable Energy Technologies for Schools. This guide is a decision-making tool intended for European municipalities and school managers. Its aim is to: assist them in choosing between the energy technologies that will be used in school building or retrofitting projects and provide them with a framework for measuring and comparing different aspects of energy performance that can be used to convince decision-makers to select sustainable energy technologies and measures. The guide is composed of three parts: an illustrative list of sustainable energy technologies, an introduction to energy performance indicators and fifteen case studies describing practical sustainable energy solutions applied to schools in seven European countries. (A.L.B.)

Forsmark site investigation. Bedrock geology - overview and excursion guide

Energy Technology Data Exchange (ETDEWEB)

Stephens, Michael B. (Geological Survey of Sweden, Uppsala (Sweden))

2010-09-15

Bearing in mind the significance of the bedrock data from the ground surface for the geological 3D modelling work, SKB decided to present excursion guides that serve in the demonstration of the bedrock geology at the ground surface in both the Forsmark (this guide) and Laxemar-Simpevarp areas. An excursion guide is also available for the Olkiluoto area in south-western Finland, which has been selected for the construction of a repository for the disposal of highly radioactive, spent nuclear fuel in Finland. The current excursion guide presents the bedrock geology and describes in detail the character of the bedrock at ten representative outcrops or outcrop areas at the ground surface in the site investigation area at Forsmark. All localities are located within or immediately adjacent to the proposed repository volume selected by SKB

Oskarshamn site investigation. Bedrock geology - overview and excursion guide

Energy Technology Data Exchange (ETDEWEB)

Wahlgren, Carl-Henric (Geological Survey of Sweden, Uppsala (Sweden))

2010-09-15

Bearing in mind the significance of the bedrock data from the ground surface for the geological 3D modelling work, SKB decided to present excursion guides that serve in the demonstration of the bedrock geology at the ground surface in both the Forsmark and Laxemar-Simpevarp (this guide) areas. An excursion guide is also available for the Olkiluoto area in south-western Finland, which has been selected for the construction of a repository for the disposal of highly radioactive, spent nuclear fuel. The current excursion guide presents the bedrock geology and describes in detail the character of the bedrock at eight representative outcrops or outcrop areas at the ground surface in the site investigation area at Laxemar-Simpevarp and at one locality north of this area, i.e. at a total of nine localities

Oskarshamn site investigation. Bedrock geology - overview and excursion guide

International Nuclear Information System (INIS)

Wahlgren, Carl-Henric

2010-09-01

Bearing in mind the significance of the bedrock data from the ground surface for the geological 3D modelling work, SKB decided to present excursion guides that serve in the demonstration of the bedrock geology at the ground surface in both the Forsmark and Laxemar-Simpevarp (this guide) areas. An excursion guide is also available for the Olkiluoto area in south-western Finland, which has been selected for the construction of a repository for the disposal of highly radioactive, spent nuclear fuel. The current excursion guide presents the bedrock geology and describes in detail the character of the bedrock at eight representative outcrops or outcrop areas at the ground surface in the site investigation area at Laxemar-Simpevarp and at one locality north of this area, i.e. at a total of nine localities

Forsmark site investigation. Bedrock geology - overview and excursion guide

International Nuclear Information System (INIS)

Stephens, Michael B.

2010-09-01

Bearing in mind the significance of the bedrock data from the ground surface for the geological 3D modelling work, SKB decided to present excursion guides that serve in the demonstration of the bedrock geology at the ground surface in both the Forsmark (this guide) and Laxemar-Simpevarp areas. An excursion guide is also available for the Olkiluoto area in south-western Finland, which has been selected for the construction of a repository for the disposal of highly radioactive, spent nuclear fuel in Finland. The current excursion guide presents the bedrock geology and describes in detail the character of the bedrock at ten representative outcrops or outcrop areas at the ground surface in the site investigation area at Forsmark. All localities are located within or immediately adjacent to the proposed repository volume selected by SKB

Field guide to fishes of the chesapeake bay

CERN Document Server

Murdy, Edward O.

2013-01-01

The only comprehensive field guide to the Chesapeake’s fishes, this book is an indispensable resource for both anglers and students of the Bay. Vivid illustrations by Val Kells complement the expertise of researchers Edward O. Murdy and John A. Musick. They describe fishes that inhabit waters ranging from low-salinity estuaries to the point where the Bay meets the Atlantic Ocean. Key features of this field guide include• full-color illustrations of more than 200 species• text that is presented adjacent to illustrations for easy reference• detailed descriptions of physical characteristics, range, occurrence in the Bay, reproduction, diet, and statistics from fisheries research• spot illustrations that highlight critical features of certain fish• illustrations of juveniles when they look different from adults• appendices that include identification keys Formatted as a compact field guide for students, scientists, researchers, and fishermen, Field Guide to Fishes of the Chesapeake Bay should be a ...

Organizational Health Literacy: Review of Theories, Frameworks, Guides, and Implementation Issues

Science.gov (United States)

Bonneville, Luc; Bouchard, Louise

2018-01-01

Organizational health literacy is described as an organization-wide effort to transform organization and delivery of care and services to make it easier for people to navigate, understand, and use information and services to take care of their health. Several health literacy guides have been developed to assist healthcare organizations with this effort, but their content has not been systematically reviewed to understand the scope and practical implications of this transformation. The objective of this study was to review (1) theories and frameworks that inform the concept of organizational health literacy, (2) the attributes of organizational health literacy as described in the guides, (3) the evidence for the effectiveness of the guides, and (4) the barriers and facilitators to implementing organizational health literacy. Drawing on a metanarrative review method, 48 publications were reviewed, of which 15 dealt with the theories and operational frameworks, 20 presented health literacy guides, and 13 addressed guided implementation of organizational health literacy. Seven theories and 9 operational frameworks have been identified. Six health literacy dimensions and 9 quality-improvement characteristics were reviewed for each health literacy guide. Evidence about the effectiveness of health literacy guides is limited at this time, but experiences with the guides were positive. Thirteen key barriers (conceived also as facilitators) were identified. Further development of organizational health literacy requires a strong and a clear connection between its vision and operationalization as an implementation strategy to patient-centered care. For many organizations, becoming health literate will require multiple, simultaneous, and radical changes. Organizational health literacy has to make sense from clinical and financial perspectives in order for organizations to embark on such transformative journey. PMID:29569968

Organizational Health Literacy: Review of Theories, Frameworks, Guides, and Implementation Issues.

Science.gov (United States)

Farmanova, Elina; Bonneville, Luc; Bouchard, Louise

2018-01-01

Organizational health literacy is described as an organization-wide effort to transform organization and delivery of care and services to make it easier for people to navigate, understand, and use information and services to take care of their health. Several health literacy guides have been developed to assist healthcare organizations with this effort, but their content has not been systematically reviewed to understand the scope and practical implications of this transformation. The objective of this study was to review (1) theories and frameworks that inform the concept of organizational health literacy, (2) the attributes of organizational health literacy as described in the guides, (3) the evidence for the effectiveness of the guides, and (4) the barriers and facilitators to implementing organizational health literacy. Drawing on a metanarrative review method, 48 publications were reviewed, of which 15 dealt with the theories and operational frameworks, 20 presented health literacy guides, and 13 addressed guided implementation of organizational health literacy. Seven theories and 9 operational frameworks have been identified. Six health literacy dimensions and 9 quality-improvement characteristics were reviewed for each health literacy guide. Evidence about the effectiveness of health literacy guides is limited at this time, but experiences with the guides were positive. Thirteen key barriers (conceived also as facilitators) were identified. Further development of organizational health literacy requires a strong and a clear connection between its vision and operationalization as an implementation strategy to patient-centered care. For many organizations, becoming health literate will require multiple, simultaneous, and radical changes. Organizational health literacy has to make sense from clinical and financial perspectives in order for organizations to embark on such transformative journey.

Removable control rod drive shaft guide

International Nuclear Information System (INIS)

Ales, M.W.; Brown, S.K.; Dixon, L.D.

1988-01-01

A removable control rod drive shaft guide is described for a control rod ''guide'' structure card, comprising: a. a substantially annular shaped main body portion having a central axial bore for receiving a control rod drive shaft and an upper exterior groove for receiving removal tooling; b. the main body portion having a reduced outer diameter at its lower section; c. a shoulder portion integral with the main body portion for supporting the main body portion on the guide structure card; d. the shoulder portion having a substantially radial bore and the reduced outer diameter lower section having a slot in alignment with the radial bore; e. a locking arm ''pivotaly'' mounted in the radial bore which protrudes into the slot and is movable between a first normal locking position for engaging the guide structure card and a second release position; f. a spring received within a second axial bore in the main body portion and biased against the locking arm for urging and locking arm into the first normal locking position; and g. a release tab at one end of the locking arm for moving the locking arm into the second release position

Physics of Non-Inertial Reference Frames

International Nuclear Information System (INIS)

Kamalov, Timur F.

2010-01-01

Physics of non-inertial reference frames is a generalizing of Newton's laws to any reference frames. It is the system of general axioms for classical and quantum mechanics. The first, Kinematics Principle reads: the kinematic state of a body free of forces conserves and equal in absolute value to an invariant of the observer's reference frame. The second, Dynamics Principle extended Newton's second law to non-inertial reference frames and also contains additional variables there are higher derivatives of coordinates. Dynamics Principle reads: a force induces a change in the kinematic state of the body and is proportional to the rate of its change. It is mean that if the kinematic invariant of the reference frame is n-th derivative with respect the time, then the dynamics of a body being affected by the force F is described by the 2n-th differential equation. The third, Statics Principle reads: the sum of all forces acting a body at rest is equal to zero.

Un guide colonial. Le Guide du Voyageur au Congo belge et au Ruanda-Urundi A colonial guidebook. Travel guide to Belgian Congo and Ruanda-Urundi

Directory of Open Access Journals (Sweden)

Henri Nicolaï

2013-03-01

. Congolese tourism, long fascinated with the myths of the Mountains of the Moon and the Source of the Nile, is essentially elitist and mainly centred on sport-hunting. Mountain gorillas, Ruwenzori climb, Tutsi dancers, Albert National Park, and Wagenia fishermen are considered the icons of this tourism first attracted by the Kivu and the Great Lakes and later the Katanga. The very first edition of the guide by Vicicongo in the 1930s is precisely entitled Congo-Nile. All these myths and settings are shown in some famous American adventure movies of the early 1950s.In the second part, the paper describes the genesis of the Guide, its main features, its plan and contents. Produced by the Colony’s official information services, the Guide describes the persistence and the results of Belgium’s civilizing role. Claiming that Congo is no country of art and history, it gives natural environment a preponderant place and provides a truncated picture of Congo’s history, reflecting the biases of that time concerning the people. This makes it a highly significant document.The paper ends with some reflections and attempts by a reporter from Canvas TV channel and a photographer from Magnum to use the 1958 Guide to roam across the country a half-century later.

Export control guide: Spent nuclear fuel reprocessing and preparation of plutonium metal

International Nuclear Information System (INIS)

1993-10-01

The international Treaty on the Non-Proliferation of Nuclear Weapons, also referred to as the Non-Proliferation Treaty (NPT), states in Article III, paragraph 2(b) that open-quotes Each State Party to the Treaty undertakes not to provide . . . equipment or material especially designed or prepared for the processing, use or production of special fissionable material to any non-nuclear-weapon State for peaceful purposes, unless the source or special fissionable material shall be subject to the safeguards required by this Article.close quotes This guide was prepared to assist export control officials in the interpretation, understanding, and implementation of export laws and controls relating to the international Trigger List for irradiated nuclear fuel reprocessing equipment, components, and materials. The guide also contains information related to the production of plutonium metal. Reprocessing and its place in the nuclear fuel cycle are described briefly; the standard procedure to prepare metallic plutonium is discussed; steps used to prepare Trigger List controls are cited; descriptions of controlled items are given; and special materials of construction are noted. This is followed by a comprehensive description of especially designed or prepared equipment, materials, and components of reprocessing and plutonium metal processes and includes photographs and/or pictorial representations. The nomenclature of the Trigger List has been retained in the numbered sections of this document for clarity

A novel technique for reference point generation to aid in intraoral scan alignment.

Science.gov (United States)

Renne, Walter G; Evans, Zachary P; Mennito, Anthony; Ludlow, Mark

2017-11-12

When using a completely digital workflow on larger prosthetic cases it is often difficult to communicate to the laboratory or chairside Computer Aided Design and Computer Aided Manufacturing system the provisional prosthetic information. The problem arises when common hard tissue data points are limited or non-existent such as in complete arch cases in which the 3D model of the complete arch provisional restorations must be aligned perfectly with the 3D model of the complete arch preparations. In these instances, soft tissue is not enough to ensure an accurate automatic or manual alignment due to a lack of well-defined reference points. A new technique is proposed for the proper digital alignment of the 3D virtual model of the provisional prosthetic to the 3D virtual model of the prepared teeth in cases where common and coincident hard tissue data points are limited. Clinical considerations: A technique is described in which fiducial composite resin dots are temporarily placed on the intraoral keratinized tissue in strategic locations prior to final impressions. These fiducial dots provide coincident and clear 3D data points that when scanned into a digital impression allow superimposition of the 3D models. Composite resin dots on keratinized tissue were successful at allowing accurate merging of provisional restoration and post-preparation 3D models for the purpose of using the provisional restorations as a guide for final CLINICAL SIGNIFICANCE: Composite resin dots placed temporarily on attached tissue were successful at allowing accurate merging of the provisional restoration 3D models to the preparation 3D models for the purposes of using the provisional restorations as a guide for final restoration design and manufacturing. In this case, they allowed precise superimposition of the 3D models made in the absence of any other hard tissue reference points, resulting in the fabrication of ideal final restorations. © 2017 Wiley Periodicals, Inc.

Double-shell tank emergency pumping guide

International Nuclear Information System (INIS)

BROWN, M.H.

1999-01-01

This Double-Shell Tank Emergency Pumping Guide provides the preplanning necessary to expeditiously remove any waste that may leak from the primary tank to the secondary tank for Hanfords 28 DSTs. The strategy is described, applicable emergency procedures are referenced, and transfer routes and pumping equipment for each tank are identified

Double-shell tank emergency pumping guide

International Nuclear Information System (INIS)

BROWN, M.H.

1999-01-01

This Double-Shell Tank Emergency Pumping Guide provides the preplanning necessary to expeditiously remove any waste that may leak from the primary tank to the secondary tank for Hanford's 28 DSTS. The strategy is described, applicable emergency procedures are referenced, and transfer routes and pumping equipment for each tank are identified

Safety design guides for containment extension for CANDU 9

International Nuclear Information System (INIS)

Lee, Duk Su; Chang, Woo Hyun; Lee, Nam Young; A. C. D. Wright

1996-03-01

This safety design guide for containment extension describes the containment isolation philosophy and containment extension requirements. The metal extensions and components falling within the scope of ASME Section III are classified in accordance with the CAN/CSA-N285.0 and CAN/CSA-N285.3. The special consideration for the leak monitoring capability, seismic qualification and inspection requirements for containment extensions, etc., are defined in this design guide. In addition, the containment isolation systems are defined and summarized schematically in appendix A. The change status of the regulatory requirements, code and standards should be traced and this safety design guide shall be updated accordingly. (Author) .new