WorldWideScience

Sample records for reference design description

  1. Light weight radioisotope heater unit (LWRHU): a technical description of the reference design

    Energy Technology Data Exchange (ETDEWEB)

    Tate, R.E.

    1982-01-01

    The Light Weight Radioisotope Heater Unit (LWRHU), a new radioisotope heater unit for use in space missions, is a /sup 238/PuO/sub 2/-fueled unit designed to provide a thermal watt in dispersed locations on a spacecraft. The LWRHU is required to maintain the temperature of a component at a level where the component will function reliably in space. Two major constraints are placed on the unit's design; it must be as light as possible and must provide enough protection to immobilize the plutonium fuel to the maximum extent in all phases of the unit's lifetime. The four components are pelletized fuel, platinum-alloy encapsulation, pyrolytic graphite thermal insulation, and high-technology graphite ablation shell. The LWRHU is a cylinder 32 mm (1.26 in.) high and 26 mm (1.02 in.) in diameter. It weighs slightly less than 40 g(.09 lb).

  2. Description of an 8 MW reference wind turbine

    Science.gov (United States)

    Desmond, Cian; Murphy, Jimmy; Blonk, Lindert; Haans, Wouter

    2016-09-01

    An 8 MW wind turbine is described in terms of mass distribution, dimensions, power curve, thrust curve, maximum design load and tower configuration. This turbine has been described as part of the EU FP7 project LEANWIND in order to facilitate research into logistics and naval architecture efficiencies for future offshore wind installations. The design of this 8 MW reference wind turbine has been checked and validated by the design consultancy DNV-GL. This turbine description is intended to bridge the gap between the NREL 5 MW and DTU 10 reference turbines and thus contribute to the standardisation of research and development activities in the offshore wind energy industry.

  3. A reference Pelton turbine design

    Science.gov (United States)

    Solemslie, B. W.; Dahlhaug, O. G.

    2012-09-01

    The designs of hydraulic turbines are usually close kept corporation secrets. Therefore, the possibility of innovation and co-operation between different academic institutions regarding a specific turbine geometry is difficult. A Ph.D.-project at the Waterpower Laboratory, NTNU, aim to design several model Pelton turbines where all measurements, simulations, the design strategy, design software in addition to the physical model will be available to the public. In the following paper a short description of the methods and the test rig that are to be utilized in the project are described. The design will be based on empirical data and NURBS will be used as the descriptive method for the turbine geometry. In addition CFX and SPH simulations will be included in the design process. Each turbine designed and produced in connection to this project will be based on the experience and knowledge gained from the previous designs. The first design will be based on the philosophy to keep a near constant relative velocity through the bucket.

  4. Project X: Accelerator Reference Design

    Energy Technology Data Exchange (ETDEWEB)

    Holmes, Stephen D. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States)

    2013-06-20

    Project X is a high-intensity proton facility being developed to support a world-leading program of Intensity Frontier physics over the next two decades at Fermilab. Project X is an integral part of the U.S. Intensity Frontier Roadmap as described in the P5 report of May 2008 [1] and within the Fermilab Strategic Plan of November 2011 [2]. This document represents Part I of the “Project X Book” describing the Project X accelerator facility and the broad range of physics research opportunities enabled by Project X. Parts II and III provide in-depth descriptions of the physics research program, both within and beyond particle physics [3]. The primary elements of the U.S. program to be supported by Project X include: Neutrino Experiments: Experimental studies of neutrino oscillations and neutrino interaction physics with ultra-intense neutrino beams provided by a high-power proton source with energies up to 120 GeV, utilizing near detectors at the Fermilab site and massive detectors at distant underground laboratories. Goal: At least 2 MW of proton beam power at any energy between 60 to 120 GeV; several hundred kW of proton beam power on target at 8 GeV. Kaon, Muon, Nucleon, and Neutron Precision Experiments: World-leading experiments studying ultra-rare kaon decays, searching for muon-to-electron conversion and nuclear electron dipole moments (EDMs), and exploring neutron properties at very high precision. Goal: MW-class proton beams supporting multiple experiments at 1 and 3 GeV, with flexible capability for providing distinct beam formats to concurrent users while allowing simultaneous operations with the neutrino program. Material Science and Nuclear Energy Applications: High-intensity accelerator, spallation, target and transmutation technology demonstrations will provide critical input into the design of future energy systems, including next generation fission reactors, nuclear waste transmutation systems and future thorium fuel-cycle power systems. Possible

  5. Descriptive Drinking Norms: For Whom Does Reference Group Matter?*

    Science.gov (United States)

    Larimer, Mary E.; Neighbors, Clayton; LaBrie, Joseph W.; Atkins, David C.; Lewis, Melissa A.; Lee, Christine M.; Kilmer, Jason R.; Kaysen, Debra L.; Pedersen, Eric r.; Montoya, Heidi; Hodge, Kimberley; Desai, Sruti; Hummer, Justin F.; Walter, Theresa

    2011-01-01

    Objective: Perceived descriptive drinking norms often differ from actual norms and are positively related to personal consumption. However, it is not clear how normative perceptions vary with specificity of the reference group. Are drinking norms more accurate and more closely related to drinking behavior as reference group specificity increases? Do these relationships vary as a function of participant demographics? The present study examined the relationship between perceived descriptive norms and drinking behavior by ethnicity (Asian or White), sex, and fraternity/sorority status. Method: Participants were 2,699 (58% female) White (75%) or Asian (25%) undergraduates from two universities who reported their own alcohol use and perceived descriptive norms for eight reference groups: "typical student"; same sex, ethnicity, or fraternity/sorority status; and all combinations of these three factors. Results: Participants generally reported the highest perceived norms for the most distal reference group (typical student), with perceptions becoming more accurate as individuals' similarity to the reference group increased. Despite increased accuracy, participants perceived that all reference groups drank more than was actually the case. Across specific subgroups (fraternity/sorority members and men) different patterns emerged. Fraternity/sorority members reliably reported higher estimates of drinking for reference groups that included fraternity/ sorority status, and, to a lesser extent, men reported higher estimates for reference groups that included men. Conclusions: The results suggest that interventions targeting normative misperceptions may need to provide feedback based on participant demography or group membership. Although reference group-specific feedback may be important for some subgroups, typical student feedback provides the largest normative discrepancy for the majority of students. PMID:21906510

  6. Descriptive drinking norms: For whom does reference group matter?

    Science.gov (United States)

    Larimer, Mary E; Neighbors, Clayton; LaBrie, Joseph W; Atkins, David C; Lewis, Melissa A; Lee, Christine M; Kilmer, Jason R; Kaysen, Debra L; Pedersen, Eric R; Montoya, Heidi; Hodge, Kimberley; Desai, Sruti; Hummer, Justin F; Walter, Theresa

    2011-09-01

    Perceived descriptive drinking norms often differ from actual norms and are positively related to personal consumption. However, it is not clear how normative perceptions vary with specificity of the reference group. Are drinking norms more accurate and more closely related to drinking behavior as reference group specificity increases? Do these relationships vary as a function of participant demographics? The present study examined the relationship between perceived descriptive norms and drinking behavior by ethnicity (Asian or White), sex, and fraternity/sorority status. Participants were 2,699 (58% female) White (75%) or Asian (25%) undergraduates from two universities who reported their own alcohol use and perceived descriptive norms for eight reference groups: "typical student"; same sex, ethnicity, or fraternity/sorority status; and all combinations of these three factors. Participants generally reported the highest perceived norms for the most distal reference group (typical student), with perceptions becoming more accurate as individuals' similarity to the reference group increased. Despite increased accuracy, participants perceived that all reference groups drank more than was actually the case. Across specific subgroups (fraternity/sorority members and men) different patterns emerged. Fraternity/sorority members reliably reported higher estimates of drinking for reference groups that included fraternity/ sorority status, and, to a lesser extent, men reported higher estimates for reference groups that included men. The results suggest that interventions targeting normative misperceptions may need to provide feedback based on participant demography or group membership. Although reference group-specific feedback may be important for some subgroups, typical student feedback provides the largest normative discrepancy for the majority of students.

  7. Reference Manual for Machine-Readable Bibliographic Descriptions. Third Edition.

    Science.gov (United States)

    Dierickx, H., Ed.; Hopkinson, A., Ed.

    A product of the UNISIST International Centre for Bibliographic Descriptions (UNIBID), this reference manual presents a standardized communication format for the exchange of machine-readable bibliographic information between bibliographic databases or other types of bibliographic information services, including libraries. Its first section defines…

  8. Fusion engineering device design description

    Energy Technology Data Exchange (ETDEWEB)

    Flanagan, C.A.; Steiner, D.; Smith, G.E.

    1981-12-01

    The US Magnetic Fusion Engineering Act of 1980 calls for the operation of a Fusion Engineering Device (FED) by 1990. It is the intent of the Act that the FED, in combination with other testing facilities, will establish the engineering feasibility of magnetic fusion energy. During 1981, the Fusion Engineering Design Center (FEDC), under the guidance of a Technical Management Board (TMB), developed a baseline design for the FED. This design is summarized herein.

  9. Fusion Engineering Device design description

    Energy Technology Data Exchange (ETDEWEB)

    Flanagan, C.A.; Steiner, D.; Smith, G.E.

    1981-12-01

    The US Magnetic Fusion Engineering Act of 1980 calls for the operation of a Fusion Engineering Device (FED) by 1990. It is the intent of the Act that the FED, in combination with other testing facilities, will establish the engineering feasibility of magnetic fusion energy. During 1981, the Fusion Engineering Design Center (FEDC), under the guidance of a Technical Management Board (TMB), developed a baseline design for the FED. This design is summarized herein.

  10. Reference repository design concept for bedded salt

    Energy Technology Data Exchange (ETDEWEB)

    Carpenter, D.W.; Martin, R.W.

    1980-10-08

    A reference design concept is presented for the subsurface portions of a nuclear waste repository in bedded salt. General geologic, geotechnical, hydrologic and geochemical data as well as descriptions of the physical systems are provided for use on generic analyses of the pre- and post-sealing performance of repositories in this geologic medium. The geology of bedded salt deposits and the regional and repository horizon stratigraphy are discussed. Structural features of salt beds including discontinuities and dissolution features are presented and their effect on repository performance is discussed. Seismic hazards and the potential effects of earthquakes on underground repositories are presented. The effect on structural stability and worker safety during construction from hydrocarbon and inorganic gases is described. Geohydrologic considerations including regional hydrology, repository scale hydrology and several hydrological failure modes are presented in detail as well as the hydrological considerations that effect repository design. Operational phase performance is discussed with respect to operations, ventilation system, shaft conveyances, waste handling and retrieval systems and receival rates of nuclear waste. Performance analysis of the post sealing period of a nuclear repository is discussed, and parameters to be used in such an analysis are presented along with regulatory constraints. Some judgements are made regarding hydrologic failure scenarios. Finally, the design and licensing process, consistent with the current licensing procedure is described in a format that can be easily understood.

  11. Printed circuit board designer's reference basics

    CERN Document Server

    Robertson, Chris

    2003-01-01

    PCB design instruction and reference manual, all in one book, with in- depth explanation of the processes and tools used in modern PCB design Standards, formulas, definitions, and procedures, plus software to tie it all together.

  12. Microprocessor Design Using Hardware Description Language

    Science.gov (United States)

    Mita, Rosario; Palumbo, Gaetano

    2008-01-01

    The following paper has been conceived to deal with the contents of some lectures aimed at enhancing courses on digital electronic, microelectronic or VLSI systems. Those lectures show how to use a hardware description language (HDL), such as the VHDL, to specify, design and verify a custom microprocessor. The general goal of this work is to teach…

  13. TWRS information locator database system design description

    Energy Technology Data Exchange (ETDEWEB)

    Knutson, B.J.

    1996-09-13

    This document gives an overview and description of the Tank Waste Remediation System (TWRS) Information Locator Database (ILD)system design. The TWRS ILD system is an inventory of information used in the TWRS Systems Engineering process to represent the TWRS Technical Baseline. The inventory is maintained in the form of a relational database developed in Paradox 4.5.

  14. Network architecture functional description and design

    Energy Technology Data Exchange (ETDEWEB)

    Stans, L.; Bencoe, M.; Brown, D.; Kelly, S.; Pierson, L.; Schaldach, C.

    1989-05-25

    This report provides a top level functional description and design for the development and implementation of the central network to support the next generation of SNL, Albuquerque supercomputer in a UNIX{reg sign} environment. It describes the network functions and provides an architecture and topology.

  15. Waste receiving and processing plant control system; system design description

    Energy Technology Data Exchange (ETDEWEB)

    LANE, M.P.

    1999-02-24

    The Plant Control System (PCS) is a heterogeneous computer system composed of numerous sub-systems. The PCS represents every major computer system that is used to support operation of the Waste Receiving and Processing (WRAP) facility. This document, the System Design Description (PCS SDD), includes several chapters and appendices. Each chapter is devoted to a separate PCS sub-system. Typically, each chapter includes an overview description of the system, a list of associated documents related to operation of that system, and a detailed description of relevant system features. Each appendice provides configuration information for selected PCS sub-systems. The appendices are designed as separate sections to assist in maintaining this document due to frequent changes in system configurations. This document is intended to serve as the primary reference for configuration of PCS computer systems. The use of this document is further described in the WRAP System Configuration Management Plan, WMH-350, Section 4.1.

  16. Cold Vacuum Drying facility HVAC system design description

    Energy Technology Data Exchange (ETDEWEB)

    SINGH, G.

    2000-09-22

    This System Design Description (SDD) addresses the HVAC system for the CVDF. The CVDF HVAC system consists of five subsystems: (1) Administration building HVAC system; (2) Process bay recirculation HVAC system; (3) Process bay local exhaust HVAC and process vent system; (4) Process general supply/exhaust HVAC system; and (5) Reference air system. The HVAC and reference air systems interface with the following systems: the fire protection control system, Monitoring and Control System (MCS), electrical power distribution system (including standby power), compressed air system, Chilled Water (CHW) system, drainage system, and other Cold Vacuum Drying (CVD) control systems not addressed in this SDD.

  17. Description, Modelling and Design of Production Systems

    DEFF Research Database (Denmark)

    Jacobsen, Peter; Rudolph, Carsten

    1997-01-01

    Design of production systems are rarely an activity in which decision makers in most production companies have much experience. In future, this activity is to be more recurrent due to more and more frequent changes in the production task. Consequently, the decision makers are in need of better...... management tools and methods for description and modelling of production systems supporting the decisions. In this article a structural framework to describe and model production systems will be introduced, and it is shown how the production system of a minor Danish manufacturer of electromechanical...

  18. 2001 – 2010 Danish Design Reference Year

    DEFF Research Database (Denmark)

    Grunnet Wang, Peter; Scharling, Mikael; Pagh Nielsen, Kristian

    This report presents the Danish Design Reference Year based on observed data from 2001 – 2010. In various sectors - i.e. building and construction, energy, etc. - the climate and weather usually plays a part in a given project. The Danish Design Reference Year dataset is a collection of data series...... for eleven specific parameters, that each represents a typical year in Denmark. The uses of the dataset may vary from simulations to statistical analysis, graphical overviews etc. The Danish land areas have been sectionalized into five to six climatological zones depending on the parameter, each...... characterized by distinct diurnal and yearly variations. The dataset consists of observed data from one station located within and representing each zone. In addition to the complete Danish Design Reference Year dataset, a subset specifically selected to be used for energy performance calculations for obtaining...

  19. Crew Transportation System Design Reference Missions

    Science.gov (United States)

    Mango, Edward J.

    2015-01-01

    Contains summaries of potential design reference mission goals for systems to transport humans to andfrom low Earth orbit (LEO) for the Commercial Crew Program. The purpose of this document is to describe Design Reference Missions (DRMs) representative of the end-to-end Crew Transportation System (CTS) framework envisioned to successfully execute commercial crew transportation to orbital destinations. The initial CTS architecture will likely be optimized to support NASA crew and NASA-sponsored crew rotation missions to the ISS, but consideration may be given in this design phase to allow for modifications in order to accomplish other commercial missions in the future. With the exception of NASA’s mission to the ISS, the remaining commercial DRMs are notional. Any decision to design or scar the CTS for these additional non-NASA missions is completely up to the Commercial Provider. As NASA’s mission needs evolve over time, this document will be periodically updated to reflect those needs.

  20. Gemini enclosure and support facility design philosophy and design description

    Science.gov (United States)

    Raybould, Keith; Ford, Robert M.; Gillett, Paul E.; Hardash, Steven G.; Pentland, Gordon

    1994-06-01

    The Gemini project is an international collaboration between the USA, United Kingdom, Canada, Chile, Argentina, and Brazil, to design, fabricate and assemble two 8 M telescopes, one on Mauna Kea in Hawaii, the other on Cerro Pachon in Chile. The telescopes will be national facilities designed to meet the Gemini Science Requirements, a document developed by the Gemini Science Committee. This paper describes the design considerations that influence the scientific performance of the enclosure and support facility, and the features that have been incorporated to meet the demanding science requirements, particularly the 0.026 arc sec allowance for `enclosure seeing'. A description of the Gemini enclosure, support facilities and site plans for Mauna Kea is given here together with a brief description of the analysis and testing that has been performed to establish the performance of the facility.

  1. COG Software Architecture Design Description Document

    Energy Technology Data Exchange (ETDEWEB)

    Buck, R M; Lent, E M

    2009-09-21

    This COG Software Architecture Design Description Document describes the organization and functionality of the COG Multiparticle Monte Carlo Transport Code for radiation shielding and criticality calculations, at a level of detail suitable for guiding a new code developer in the maintenance and enhancement of COG. The intended audience also includes managers and scientists and engineers who wish to have a general knowledge of how the code works. This Document is not intended for end-users. This document covers the software implemented in the standard COG Version 10, as released through RSICC and IAEA. Software resources provided by other institutions will not be covered. This document presents the routines grouped by modules and in the order of the three processing phases. Some routines are used in multiple phases. The routine description is presented once - the first time the routine is referenced. Since this is presented at the level of detail for guiding a new code developer, only the routines invoked by another routine that are significant for the processing phase that is being detailed are presented. An index to all routines detailed is included. Tables for the primary data structures are also presented.

  2. ILC Reference Design Report Volume 4 - Detectors

    CERN Document Server

    Behnke, Ties; Jaros, John; Miyamoto, Akiya; Aarons, Gerald; Abe, Toshinori; Abernathy, Jason; Ablikim, Medina; Abramowicz, Halina; Adey, David; Adloff, Catherine; Adolphsen, Chris; Afanaciev, Konstantin; Agapov, Ilya; Ahn, Jung-Keun; Aihara, Hiroaki; Akemoto, Mitsuo; del Carmen Alabau, Maria; Albert, Justin; Albrecht, Hartwig; Albrecht, Michael; Alesini, David; Alexander, Gideon; Alexander, Jim; Allison, Wade; Amann, John; Amirikas, Ramila; An, Qi; Anami, Shozo; Ananthanarayan, B.; Anderson, Terry; Andricek, Ladislav; Anduze, Marc; Anerella, Michael; Anfimov, Nikolai; Angal-Kalinin, Deepa; Antipov, Sergei; Antoine, Claire; Aoki, Mayumi; Aoza, Atsushi; Aplin, Steve; Appleby, Rob; Arai, Yasuo; Araki, Sakae; Arkan, Tug; Arnold, Ned; Arnold, Ray; Arnowitt, Richard; Artru, Xavier; Arya, Kunal; Aryshev, Alexander; Asakawa, Eri; Asiri, Fred; Asner, David; Atac, Muzaffer; Atoian, Grigor; Attié, David; Augustin, Jean-Eudes; Augustine, David B.; Ayres, Bradley; Aziz, Tariq; Baars, Derek; Badaud, Frederique; Baddams, Nigel; Bagger, Jonathan; Bai, Sha; Bailey, David; Bailey, Ian R.; Baker, David; Balalykin, Nikolai I.; Balbuena, Juan Pablo; Baldy, Jean-Luc; Ball, Markus; Ball, Maurice; Ballestrero, Alessandro; Ballin, Jamie; Baltay, Charles; Bambade, Philip; Ban, Syuichi; Band, Henry; Bane, Karl; Banerjee, Bakul; Barbanotti, Serena; Barbareschi, Daniele; Barbaro-Galtieri, Angela; Barber, Desmond P.; Barbi, Mauricio; Bardin, Dmitri Y.; Barish, Barry; Barklow, Timothy L.; Barlow, Roger; Barnes, Virgil E.; Barone, Maura; Bartels, Christoph; Bartsch, Valeria; Basu, Rahul; Battaglia, Marco; Batygin, Yuri; Baudot, Jerome; Baur, Ulrich; Elwyn Baynham, D.; Beard, Carl; Bebek, Chris; Bechtle, Philip; Becker, Ulrich J.; Bedeschi, Franco; Bedjidian, Marc; Behera, Prafulla; Bellantoni, Leo; Bellerive, Alain; Bellomo, Paul; Bentson, Lynn D.; Benyamna, Mustapha; Bergauer, Thomas; Berger, Edmond; Bergholz, Matthias; Beri, Suman; Berndt, Martin; Bernreuther, Werner; Bertolini, Alessandro; Besancon, Marc; Besson, Auguste; Beteille, Andre; Bettoni, Simona; Beyer, Michael; Bhandari, R.K.; Bharadwaj, Vinod; Bhatnagar, Vipin; Bhattacharya, Satyaki; Bhattacharyya, Gautam; Bhattacherjee, Biplob; Bhuyan, Ruchika; Bi, Xiao-Jun; Biagini, Marica; Bialowons, Wilhelm; Biebel, Otmar; Bieler, Thomas; Bierwagen, John; Birch, Alison; Bisset, Mike; Biswal, S.S.; Blackmore, Victoria; Blair, Grahame; Blanchard, Guillaume; Blazey, Gerald; Blue, Andrew; Blümlein, Johannes; Boffo, Christian; Bohn, Courtlandt; Boiko, V.I.; Boisvert, Veronique; Bondarchuk, Eduard N.; Boni, Roberto; Bonvicini, Giovanni; Boogert, Stewart; Boonekamp, Maarten; Boorman, Gary; Borras, Kerstin; Bortoletto, Daniela; Bosco, Alessio; Bosio, Carlo; Bosland, Pierre; Bosotti, Angelo; Boudry, Vincent; Boumediene, Djamel-Eddine; Bouquet, Bernard; Bourov, Serguei; Bowden, Gordon; Bower, Gary; Boyarski, Adam; Bozovic-Jelisavcic, Ivanka; Bozzi, Concezio; Brachmann, Axel; Bradshaw, Tom W.; Brandt, Andrew; Brasser, Hans Peter; Brau, Benjamin; Brau, James E.; Breidenbach, Martin; Bricker, Steve; Brient, Jean-Claude; Brock, Ian; Brodsky, Stanley; Brooksby, Craig; Broome, Timothy A.; Brown, David; Brown, David; Brownell, James H.; Bruchon, Mélanie; Brueck, Heiner; Brummitt, Amanda J.; Brun, Nicole; Buchholz, Peter; Budagov, Yulian A.; Bulgheroni, Antonio; Bulyak, Eugene; Bungau, Adriana; Bürger, Jochen; Burke, Dan; Burkhart, Craig; Burrows, Philip; Burt, Graeme; Burton, David; Büsser, Karsten; Butler, John; Butterworth, Jonathan; Buzulutskov, Alexei; Cabruja, Enric; Caccia, Massimo; Cai, Yunhai; Calcaterra, Alessandro; Caliier, Stephane; Camporesi, Tiziano; Cao, Jun-Jie; Cao, J.S.; Capatina, Ofelia; Cappellini, Chiara; Carcagno, Ruben; Carena, Marcela; Carloganu, Cristina; Carosi, Roberto; Stephen Carr, F.; Carrion, Francisco; Carter, Harry F.; Carter, John; Carwardine, John; Cassel, Richard; Cassell, Ronald; Cavallari, Giorgio; Cavallo, Emanuela; Cembranos, Jose A.R.; Chakraborty, Dhiman; Chandez, Frederic; Charles, Matthew; Chase, Brian; Chattopadhyay, Subhasis; Chauveau, Jacques; Chefdeville, Maximilien; Chehab, Robert; Chel, Stéphane; Chelkov, Georgy; Chen, Chiping; Chen, He Sheng; Chen, Huai Bi; Chen, Jia Er; Chen, Sen Yu; Chen, Shaomin; Chen, Shenjian; Chen, Xun; Chen, Yuan Bo; Cheng, Jian; Chevallier, M.; Chi, Yun Long; Chickering, William; Cho, Gi-Chol; Cho, Moo-Hyun; Choi, Jin-Hyuk; Choi, Jong Bum; Choi, Seong Youl; Choi, Young-Il; Choudhary, Brajesh; Choudhury, Debajyoti; Rai Choudhury, S.; Christian, David; Christian, Glenn; Christophe, Grojean; Chung, Jin-Hyuk; Church, Mike; Ciborowski, Jacek; Cihangir, Selcuk; Ciovati, Gianluigi; Clarke, Christine; Clarke, Don G.; Clarke, James A.; Clements, Elizabeth; Coca, Cornelia; Coe, Paul; Cogan, John; Colas, Paul; Collard, Caroline; Colledani, Claude; Combaret, Christophe; Comerma, Albert; Compton, Chris; Constance, Ben; Conway, John; Cook, Ed; Cooke, Peter; Cooper, William; Corcoran, Sean; Cornat, Rémi; Corner, Laura; Cortina Gil, Eduardo; Clay Corvin, W.; Cotta Ramusino, Angelo; Cowan, Ray; Crawford, Curtis; Cremaldi, Lucien M; Crittenden, James A.; Cussans, David; Cvach, Jaroslav; da Silva, Wilfrid; Dabiri Khah, Hamid; Dabrowski, Anne; Dabrowski, Wladyslaw; Dadoun, Olivier; Dai, Jian Ping; Dainton, John; Daly, Colin; Danilov, Mikhail; Daniluk, Witold; Daram, Sarojini; Datta, Anindya; Dauncey, Paul; David, Jacques; Davier, Michel; Davies, Ken P.; Dawson, Sally; De Boer, Wim; De Curtis, Stefania; De Groot, Nicolo; de la Taille, Christophe; de Lira, Antonio; De Roeck, Albert; de Sangro, Riccardo; De Santis,Stefano; Deacon, Laurence; Deandrea, Aldo; Dehmelt, Klaus; Delagnes, Eric; Delahaye, Jean-Pierre; Delebecque, Pierre; Delerue, Nicholas; Delferriere, Olivier; Demarteau, Marcel; Deng, Zhi; Denisov, Yu.N.; Densham, Christopher J.; Desch, Klaus; Deshpande, Nilendra; Devanz, Guillaume; Devetak, Erik; Dexter, Amos; Di benedetto, Vito; Diéguez, Angel; Diener, Ralf; Dinh, Nguyen Dinh; Dixit, Madhu; Dixit, Sudhir; Djouadi, Abdelhak; Dolezal, Zdenek; Dollan, Ralph; Dong, Dong; Dong, Hai Yi; Dorfan, Jonathan; Dorokhov, Andrei; Doucas, George; Downing, Robert; Doyle, Eric; Doziere, Guy; Drago, Alessandro; Dragt, Alex; Drake, Gary; Drásal, Zbynek; Dreiner, Herbert; Drell, Persis; Driouichi, Chafik; Drozhdin, Alexandr; Drugakov, Vladimir; Du, Shuxian; Dugan, Gerald; Duginov, Viktor; Dulinski, Wojciech; Dulucq, Frederic; Dutta, Sukanta; Dwivedi, Jishnu; Dychkant, Alexandre; Dzahini, Daniel; Eckerlin, Guenter; Edwards, Helen; Ehrenfeld, Wolfgang; Ehrlichman, Michael; Ehrlichmann, Heiko; Eigen, Gerald; Elagin, Andrey; Elementi, Luciano; Eliasson, Peder; Ellis, John; Ellwood, George; Elsen, Eckhard; Emery, Louis; Enami, Kazuhiro; Endo, Kuninori; Enomoto, Atsushi; Eozénou, Fabien; Erbacher, Robin; Erickson, Roger; Oleg Eyser, K.; Fadeyev, Vitaliy; Fang, Shou Xian; Fant, Karen; Fasso, Alberto; Faucci Giannelli, Michele; Fehlberg, John; Feld, Lutz; Feng, Jonathan L.; Ferguson, John; Fernandez-Garcia, Marcos; Luis Fernandez-Hernando, J.; Fiala, Pavel; Fieguth, Ted; Finch, Alexander; Finocchiaro, Giuseppe; Fischer, Peter; Fisher, Peter; Eugene Fisk, H.; Fitton, Mike D.; Fleck, Ivor; Fleischer, Manfred; Fleury, Julien; Flood, Kevin; Foley, Mike; Ford, Richard; Fortin, Dominique; Foster, Brian; Fourches, Nicolas; Francis, Kurt; Frey, Ariane; Frey, Raymond; Friedsam, Horst; Frisch, Josef; Frishman, Anatoli; Fuerst, Joel; Fujii, Keisuke; Fujimoto, Junpei; Fukuda, Masafumi; Fukuda, Shigeki; Funahashi, Yoshisato; Funk, Warren; Furletova, Julia; Furukawa, Kazuro; Furuta, Fumio; Fusayasu, Takahiro; Fuster, Juan; Gadow, Karsten; Gaede, Frank; Gaglione, Renaud; Gai, Wei; Gajewski, Jan; Galik, Richard; Galkin, Alexei; Galkin, Valery; Gallin-Martel, Laurent; Gannaway, Fred; Gao, Jian She; Gao, Jie; Gao, Yuanning; Garbincius, Peter; Garcia-Tabares, Luis; Garren, Lynn; Garrido, Luís; Garutti, Erika; Garvey, Terry; Garwin, Edward; Gascón, David; Gastal, Martin; Gatto, Corrado; Gatto, Raoul; Gay, Pascal; Ge, Lixin; Ge, Ming Qi; Ge, Rui; Geiser, Achim; Gellrich, Andreas; Genat, Jean-Francois; Geng, Zhe Qiao; Gentile, Simonetta; Gerbick, Scot; Gerig, Rod; Ghosh, Dilip Kumar; Ghosh, Kirtiman; Gibbons, Lawrence; Giganon, Arnaud; Gillespie, Allan; Gillman, Tony; Ginzburg, Ilya; Giomataris, Ioannis; Giunta, Michele; Gladkikh, Peter; Gluza, Janusz; Godbole, Rohini; Godfrey, Stephen; Goldhaber, Gerson; Goldstein, Joel; Gollin, George D.; Gonzalez-Sanchez, Francisco Javier; Goodrick, Maurice; Gornushkin, Yuri; Gostkin, Mikhail; Gottschalk, Erik; Goudket, Philippe; Gough Eschrich, Ivo; Gournaris, Filimon; Graciani, Ricardo; Graf, Norman; Grah, Christian; Grancagnolo, Francesco; Grandjean, Damien; Grannis, Paul; Grassellino, Anna; Graugés, Eugeni; Gray, Stephen; Green, Michael; Greenhalgh, Justin; Greenshaw, Timothy; Grefe, Christian; Gregor, Ingrid-Maria; Grenier, Gerald; Grimes, Mark; Grimm, Terry; Gris, Philippe; Grivaz, Jean-Francois; Groll, Marius; Gronberg, Jeffrey; Grondin, Denis; Groom, Donald; Gross, Eilam; Grunewald, Martin; Grupen, Claus; Grzelak, Grzegorz; Gu, Jun; Gu, Yun-Ting; Guchait, Monoranjan; Guiducci, Susanna; Guler, Ali Murat; Guler, Hayg; Gulmez, Erhan; Gunion, John; Guo, Zhi Yu; Gurtu, Atul; Ha, Huy Bang; Haas, Tobias; Haase, Andy; Haba, Naoyuki; Haber, Howard; Haensel, Stephan; Hagge, Lars; Hagura, Hiroyuki; Hajdu, Csaba; Haller, Gunther; Haller, Johannes; Hallermann, Lea; Halyo, Valerie; Hamaguchi, Koichi; Hammond, Larry; Han, Liang; Han, Tao; Hand, Louis; Handu, Virender K.; Hano, Hitoshi; Hansen, Christian; Hansen, Jørn Dines; Hansen, Jorgen Beck; Hara, Kazufumi; Harder, Kristian; Hartin, Anthony; Hartung, Walter; Hast, Carsten; Hauptman, John; Hauschild, Michael; Hauviller, Claude; Havranek, Miroslav; Hawkes, Chris; Hawkings, Richard; Hayano, Hitoshi; Hazumi, Masashi; He, An; He, Hong Jian; Hearty, Christopher; Heath, Helen; Hebbeker, Thomas; Hedberg, Vincent; Hedin, David; Heifets, Samuel; Heinemeyer, Sven; Heini, Sebastien; Helebrant, Christian; Helms, Richard; Heltsley, Brian; Henrot-Versille, Sophie; Henschel, Hans; Hensel, Carsten; Hermel, Richard; Herms, Atilà; Herten, Gregor; Hesselbach, Stefan; Heuer, Rolf-Dieter; Heusch, Clemens A.; Hewett, Joanne; Higashi, Norio; Higashi, Takatoshi; Higashi, Yasuo; Higo, Toshiyasu; Hildreth, Michael D.; Hiller, Karlheinz; Hillert, Sonja; Hillier, Stephen James; Himel, Thomas; Himmi, Abdelkader; Hinchliffe, Ian; Hioki, Zenro; Hirano, Koichiro; Hirose, Tachishige; Hisamatsu, Hiromi; Hisano, Junji; Hlaing, Chit Thu; Hock, Kai Meng; Hoeferkamp, Martin; Hohlfeld, Mark; Honda, Yousuke; Hong, Juho; Hong, Tae Min; Honma, Hiroyuki; Horii, Yasuyuki; Horvath, Dezso; Hosoyama, Kenji; Hostachy, Jean-Yves; Hou, Mi; Hou, Wei-Shu; Howell, David; Hronek, Maxine; Hsiung, Yee B.; Hu, Bo; Hu, Tao; Huang, Jung-Yun; Huang, Tong Ming; Huang, Wen Hui; Huedem, Emil; Huggard, Peter; Hugonie, Cyril; Hu-Guo, Christine; Huitu, Katri; Hwang, Youngseok; Idzik, Marek; Ignatenko, Alexandr; Ignatov, Fedor; Ikeda, Hirokazu; Ikematsu, Katsumasa; Ilicheva, Tatiana; Imbault, Didier; Imhof, Andreas; Incagli, Marco; Ingbir, Ronen; Inoue, Hitoshi; Inoue, Youichi; Introzzi, Gianluca; Ioakeimidi, Katerina; Ishihara, Satoshi; Ishikawa, Akimasa; Ishikawa, Tadashi; Issakov, Vladimir; Ito, Kazutoshi; Ivanov, V.V.; Ivanov, Valentin; Ivanyushenkov, Yury; Iwasaki, Masako; Iwashita, Yoshihisa; Jackson, David; Jackson, Frank; Jacobsen, Bob; Jaganathan, Ramaswamy; Jamison, Steven; Janssen, Matthias Enno; Jaramillo-Echeverria, Richard; Jauffret, Clement; Jawale, Suresh B.; Jeans, Daniel; Jedziniak, Ron; Jeffery, Ben; Jehanno, Didier; Jenner, Leo J.; Jensen, Chris; Jensen, David R.; Jiang, Hairong; Jiang, Xiao Ming; Jimbo, Masato; Jin, Shan; Keith Jobe, R.; Johnson, Anthony; Johnson, Erik; Johnson, Matt; Johnston, Michael; Joireman, Paul; Jokic, Stevan; Jones, James; Jones, Roger M.; Jongewaard, Erik; Jönsson, Leif; Joshi, Gopal; Joshi, Satish C.; Jung, Jin-Young; Junk, Thomas; Juste, Aurelio; Kado, Marumi; Kadyk, John; Käfer, Daniela; Kako, Eiji; Kalavase, Puneeth; Kalinin, Alexander; Kalinowski, Jan; Kamitani, Takuya; Kamiya, Yoshio; Kamiya, Yukihide; Kamoshita, Jun-ichi; Kananov, Sergey; Kanaya, Kazuyuki; Kanazawa, Ken-ichi; Kanemura, Shinya; Kang, Heung-Sik; Kang, Wen; Kanjial, D.; Kapusta, Frédéric; Karataev, Pavel; Karchin, Paul E.; Karlen, Dean; Karyotakis, Yannis; Kashikhin, Vladimir; Kashiwagi, Shigeru; Kasley, Paul; Katagiri, Hiroaki; Kato, Takashi; Kato, Yukihiro; Katzy, Judith; Kaukher, Alexander; Kaur, Manjit; Kawagoe, Kiyotomo; Kawamura, Hiroyuki; Kazakov, Sergei; Kekelidze, V.D.; Keller, Lewis; Kelley, Michael; Kelly, Marc; Kelly, Michael; Kennedy, Kurt; Kephart, Robert; Keung, Justin; Khainovski, Oleg; Khan, Sameen Ahmed; Khare, Prashant; Khovansky, Nikolai; Kiesling, Christian; Kikuchi, Mitsuo; Kilian, Wolfgang; Killenberg, Martin; Kim, Donghee; Kim, Eun San; Kim, Eun-Joo; Kim, Guinyun; Kim, Hongjoo; Kim, Hyoungsuk; Kim, Hyun-Chui; Kim, Jonghoon; Kim, Kwang-Je; Kim, Kyung Sook; Kim, Peter; Kim, Seunghwan; Kim, Shin-Hong; Kim, Sun Kee; Kim, Tae Jeong; Kim, Youngim; Kim, Young-Kee; Kimmitt, Maurice; Kirby, Robert; Kircher, François; Kisielewska, Danuta; Kittel, Olaf; Klanner, Robert; Klebaner, Arkadiy L.; Kleinwort, Claus; Klimkovich, Tatsiana; Klinkby, Esben; Kluth, Stefan; Knecht, Marc; Kneisel, Peter; Ko, In Soo; Ko, Kwok; Kobayashi, Makoto; Kobayashi, Nobuko; Kobel, Michael; Koch, Manuel; Kodys, Peter; Koetz, Uli; Kohrs, Robert; Kojima, Yuuji; Kolanoski, Hermann; Kolodziej, Karol; Kolomensky, Yury G.; Komamiya, Sachio; Kong, Xiang Cheng; Konigsberg, Jacobo; Korbel, Volker; Koscielniak, Shane; Kostromin, Sergey; Kowalewski, Robert; Kraml, Sabine; Krammer, Manfred; Krasnykh, Anatoly; Krautscheid, Thorsten; Krawczyk, Maria; James Krebs, H.; Krempetz, Kurt; Kribs, Graham; Krishnagopal, Srinivas; Kriske, Richard; Kronfeld, Andreas; Kroseberg, Jürgen; Kruchonak, Uladzimir; Kruecker, Dirk; Krüger, Hans; Krumpa, Nicholas A.; Krumshtein, Zinovii; Kuang, Yu Ping; Kubo, Kiyoshi; Kuchler, Vic; Kudoh, Noboru; Kulis, Szymon; Kumada, Masayuki; Kumar, Abhay; Kume, Tatsuya; Kundu, Anirban; Kurevlev, German; Kurihara, Yoshimasa; Kuriki, Masao; Kuroda, Shigeru; Kuroiwa, Hirotoshi; Kurokawa, Shin-ichi; Kusano, Tomonori; Kush, Pradeep K.; Kutschke, Robert; Kuznetsova, Ekaterina; Kvasnicka, Peter; Kwon, Youngjoon; Labarga, Luis; Lacasta, Carlos; Lackey, Sharon; Lackowski, Thomas W.; Lafaye, Remi; Lafferty, George; Lagorio, Eric; Laktineh, Imad; Lal, Shankar; Laloum, Maurice; Lam, Briant; Lancaster, Mark; Lander, Richard; Lange, Wolfgang; Langenfeld, Ulrich; Langeveld, Willem; Larbalestier, David; Larsen, Ray; Lastovicka, Tomas; Lastovicka-Medin, Gordana; Latina, Andrea; Latour, Emmanuel; Laurent, Lisa; Le, Ba Nam; Le, Duc Ninh; Le Diberder, Francois; Dû, Patrick Le; Lebbolo, Hervé; Lebrun, Paul; Lecoq, Jacques; Lee, Sung-Won; Lehner, Frank; Leibfritz, Jerry; Lenkszus, Frank; Lesiak, Tadeusz; Levy, Aharon; Lewandowski, Jim; Leyh, Greg; Li, Cheng; Li, Chong Sheng; Li, Chun Hua; Li, Da Zhang; Li, Gang; Li, Jin; Li, Shao Peng; Li, Wei Ming; Li, Weiguo; Li, Xiao Ping; Li, Xue-Qian; Li, Yuanjing; Li, Yulan; Li, Zenghai; Li, Zhong Quan; Liang, Jian Tao; Liao, Yi; Lilje, Lutz; Guilherme Lima, J.; Lintern, Andrew J.; Lipton, Ronald; List, Benno; List, Jenny; Liu, Chun; Liu, Jian Fei; Liu, Ke Xin; Liu, Li Qiang; Liu, Shao Zhen; Liu, Sheng Guang; Liu, Shubin; Liu, Wanming; Liu, Wei Bin; Liu, Ya Ping; Liu, Yu Dong; Lockyer, Nigel; Logan, Heather E.; Logatchev, Pavel V.; Lohmann, Wolfgang; Lohse, Thomas; Lola, Smaragda; Lopez-Virto, Amparo; Loveridge, Peter; Lozano, Manuel; Lu, Cai-Dian; Lu, Changguo; Lu, Gong-Lu; Lu, Wen Hui; Lubatti, Henry; Lucotte, Arnaud; Lundberg, Björn; Lundin, Tracy; Luo, Mingxing; Luong, Michel; Luth, Vera; Lutz, Benjamin; Lutz, Pierre; Lux, Thorsten; Luzniak, Pawel; Lyapin, Alexey; Lykken, Joseph; Lynch, Clare; Ma, Li; Ma, Lili; Ma, Qiang; Ma, Wen-Gan; Macfarlane, David; Maciel, Arthur; MacLeod, Allan; MacNair, David; Mader, Wolfgang; Magill, Stephen; Magnan, Anne-Marie; Maiheu, Bino; Maity, Manas; Majchrzak, Millicent; Majumder, Gobinda; Makarov, Roman; Makowski, Dariusz; Malaescu, Bogdan; Mallik, C.; Mallik, Usha; Malton, Stephen; Malyshev, Oleg B.; Malysheva, Larisa I.; Mammosser, John; Mamta; Mamuzic, Judita; Manen, Samuel; Manghisoni, Massimo; Manly, Steven; Marcellini, Fabio; Marcisovsky, Michal; Markiewicz, Thomas W.; Marks, Steve; Marone, Andrew; Marti, Felix; Martin, Jean-Pierre; Martin, Victoria; Martin-Chassard, Gisèle; Martinez, Manel; Martinez-Rivero, Celso; Martsch, Dennis; Martyn, Hans-Ulrich; Maruyama, Takashi; Masuzawa, Mika; Mathez, Hervé; Matsuda, Takeshi; Matsumoto, Hiroshi; Matsumoto, Shuji; Matsumoto, Toshihiro; Matsunaga, Hiroyuki; Mättig, Peter; Mattison, Thomas; Mavromanolakis, Georgios; Mawatari, Kentarou; Mazzacane, Anna; McBride, Patricia; McCormick, Douglas; McCormick, Jeremy; McDonald, Kirk T.; McGee, Mike; McIntosh, Peter; McKee, Bobby; McPherson, Robert A.; Meidlinger, Mandi; Meier, Karlheinz; Mele, Barbara; Meller, Bob; Melzer-Pellmann, Isabell-Alissandra; Mendez, Hector; Mercer, Adam; Merkin, Mikhail; Meshkov, I.N.; Messner, Robert; Metcalfe, Jessica; Meyer, Chris; Meyer, Hendrik; Meyer, Joachim; Meyer, Niels; Meyners, Norbert; Michelato, Paolo; Michizono, Shinichiro; Mihalcea, Daniel; Mihara, Satoshi; Mihara, Takanori; Mikami, Yoshinari; Mikhailichenko, Alexander A.; Milardi, Catia; Miller, David J.; Miller, Owen; Miller, Roger J.; Milstene, Caroline; Mimashi, Toshihiro; Minashvili, Irakli; Miquel, Ramon; Mishra, Shekhar; Mitaroff, Winfried; Mitchell, Chad; Miura, Takako; Miyata, Hitoshi; Mjörnmark, Ulf; Mnich, Joachim; Moenig, Klaus; Moffeit, Kenneth; Mokhov, Nikolai; Molloy, Stephen; Monaco, Laura; Monasterio, Paul R.; Montanari, Alessandro; Moon, Sung Ik; Moortgat-Pick, Gudrid A.; Mora de Freitas, Paulo; Morel, Federic; Moretti, Stefano; Morgunov, Vasily; Mori, Toshinori; Morin, Laurent; Morisseau, François; Morita, Yoshiyuki; Morita, Youhei; Morita, Yuichi; Morozov, Nikolai; Morozumi, Yuichi; Morse, William; Moser, Hans-Guenther; Moultaka, Gilbert; Mtingwa, Sekazi; Mudrinic, Mihajlo; Mueller, Alex; Mueller, Wolfgang; Muennich, Astrid; Muhlleitner, Milada Margarete; Mukherjee, Bhaskar; Mukhopadhyaya, Biswarup; Müller, Thomas; Munro, Morrison; Murayama, Hitoshi; Muto, Toshiya; Myneni, Ganapati Rao; Nabhiraj, P.Y.; Nagaitsev, Sergei; Nagamine, Tadashi; Nagano, Ai; Naito, Takashi; Nakai, Hirotaka; Nakajima, Hiromitsu; Nakamura, Isamu; Nakamura, Tomoya; Nakanishi, Tsutomu; Nakao, Katsumi; Nakao, Noriaki; Nakayoshi, Kazuo; Nam, Sang; Namito, Yoshihito; Namkung, Won; Nantista, Chris; Napoly, Olivier; Narain, Meenakshi; Naroska, Beate; Nauenberg, Uriel; Nayyar, Ruchika; Neal, Homer; Nelson, Charles; Nelson, Janice; Nelson, Timothy; Nemecek, Stanislav; Neubauer, Michael; Neuffer, David; Newman, Myriam Q.; Nezhevenko, Oleg; Ng, Cho-Kuen; Nguyen, Anh Ky; Nguyen, Minh; Van Nguyen Thi,Hong; Niebuhr, Carsten; Niehoff, Jim; Niezurawski, Piotr; Nishitani, Tomohiro; Nitoh, Osamu; Noguchi, Shuichi; Nomerotski, Andrei; Noonan, John; Norbeck, Edward; Nosochkov, Yuri; Notz, Dieter; Nowak, Grazyna; Nowak, Hannelies; Noy, Matthew; Nozaki, Mitsuaki; Nyffeler, Andreas; Nygren, David; Oddone, Piermaria; O'Dell, Joseph; Oh, Jong-Seok; Oh, Sun Kun; Ohkuma, Kazumasa; Ohlerich, Martin; Ohmi, Kazuhito; Ohnishi, Yukiyoshi; Ohsawa, Satoshi; Ohuchi, Norihito; Oide, Katsunobu; Okada, Nobuchika; Okada, Yasuhiro; Okamura, Takahiro; Okugi, Toshiyuki; Okumi, Shoji; Okumura, Ken-ichi; Olchevski, Alexander; Oliver, William; Olivier, Bob; Olsen, James; Olsen, Jeff; Olsen, Stephen; Olshevsky, A.G.; Olsson, Jan; Omori, Tsunehiko; Onel, Yasar; Onengut, Gulsen; Ono, Hiroaki; Onoprienko, Dmitry; Oreglia, Mark; Oren, Will; Orimoto, Toyoko J.; Oriunno, Marco; Orlandea, Marius Ciprian; Oroku, Masahiro; Orr, Lynne H.; Orr, Robert S.; Oshea, Val; Oskarsson, Anders; Osland, Per; Ossetski, Dmitri; Österman, Lennart; Ostiguy, Francois; Otono, Hidetoshi; Ottewell, Brian; Ouyang, Qun; Padamsee, Hasan; Padilla, Cristobal; Pagani, Carlo; Palmer, Mark A.; Pam, Wei Min; Pande, Manjiri; Pande, Rajni; Pandit, V.S.; Pandita, P.N.; Pandurovic, Mila; Pankov, Alexander; Panzeri, Nicola; Papandreou, Zisis; Paparella, Rocco; Para, Adam; Park, Hwanbae; Parker, Brett; Parkes, Chris; Parma, Vittorio; Parsa, Zohreh; Parsons, Justin; Partridge, Richard; Pasquinelli, Ralph; Pásztor, Gabriella; Paterson, Ewan; Patrick, Jim; Patteri, Piero; Ritchie Patterson, J.; Pauletta, Giovanni; Paver, Nello; Pavlicek, Vince; Pawlik, Bogdan; Payet, Jacques; Pchalek, Norbert; Pedersen, John; Pei, Guo Xi; Pei, Shi Lun; Pelka, Jerzy; Pellegrini, Giulio; Pellett, David; Peng, G.X.; Penn, Gregory; Penzo, Aldo; Perry, Colin; Peskin, Michael; Peters, Franz; Petersen, Troels Christian; Peterson, Daniel; Peterson, Thomas; Petterson, Maureen; Pfeffer, Howard; Pfund, Phil; Phelps, Alan; Van Phi, Quang; Phillips, Jonathan; Phinney, Nan; Piccolo, Marcello; Piemontese, Livio; Pierini, Paolo; Thomas Piggott, W.; Pike, Gary; Pillet, Nicolas; Jayawardena, Talini Pinto; Piot, Phillippe; Pitts, Kevin; Pivi, Mauro; Plate, Dave; Pleier, Marc-Andre; Poblaguev, Andrei; Poehler, Michael; Poelker, Matthew; Poffenberger, Paul; Pogorelsky, Igor; Poirier, Freddy; Poling, Ronald; Poole, Mike; Popescu, Sorina; Popielarski, John; Pöschl, Roman; Postranecky, Martin; Potukochi, Prakash N.; Prast, Julie; Prat, Serge; Preger, Miro; Prepost, Richard; Price, Michael; Proch, Dieter; Puntambekar, Avinash; Qin, Qing; Qu, Hua Min; Quadt, Arnulf; Quesnel, Jean-Pierre; Radeka, Veljko; Rahmat, Rahmat; Rai, Santosh Kumar; Raimondi, Pantaleo; Ramberg, Erik; Ranjan, Kirti; Rao, Sista V.L.S.; Raspereza, Alexei; Ratti, Alessandro; Ratti, Lodovico; Raubenheimer, Tor; Raux, Ludovic; Ravindran, V.; Raychaudhuri, Sreerup; Re, Valerio; Rease, Bill; Reece, Charles E.; Regler, Meinhard; Rehlich, Kay; Reichel, Ina; Reichold, Armin; Reid, John; Reid, Ron; Reidy, James; Reinhard, Marcel; Renz, Uwe; Repond, Jose; Resta-Lopez, Javier; Reuen, Lars; Ribnik, Jacob; Rice, Tyler; Richard, François; Riemann, Sabine; Riemann, Tord; Riles, Keith; Riley, Daniel; Rimbault, Cécile; Rindani, Saurabh; Rinolfi, Louis; Risigo, Fabio; Riu, Imma; Rizhikov, Dmitri; Rizzo, Thomas; Rochford, James H.; Rodriguez, Ponciano; Roeben, Martin; Rolandi, Gigi; Roodman, Aaron; Rosenberg, Eli; Roser, Robert; Ross, Marc; Rossel, François; Rossmanith, Robert; Roth, Stefan; Rougé, André; Rowe, Allan; Roy, Amit; Roy, Sendhunil B.; Roy, Sourov; Royer, Laurent; Royole-Degieux, Perrine; Royon, Christophe; Ruan, Manqi; Rubin, David; Ruehl, Ingo; Jimeno, Alberto Ruiz; Ruland, Robert; Rusnak, Brian; Ryu, Sun-Young; Sabbi, Gian Luca; Sadeh, Iftach; Sadygov, Ziraddin Y; Saeki, Takayuki; Sagan, David; Sahni, Vinod C.; Saini, Arun; Saito, Kenji; Saito, Kiwamu; Sajot, Gerard; Sakanaka, Shogo; Sakaue, Kazuyuki; Salata, Zen; Salih, Sabah; Salvatore, Fabrizio; Samson, Joergen; Sanami, Toshiya; Levi Sanchez, Allister; Sands, William; Santic, John; Sanuki, Tomoyuki; Sapronov, Andrey; Sarkar, Utpal; Sasao, Noboru; Satoh, Kotaro; Sauli, Fabio; Saunders, Claude; Saveliev, Valeri; Savoy-Navarro, Aurore; Sawyer, Lee; Saxton, Laura; Schäfer, Oliver; Schälicke, Andreas; Schade, Peter; Schaetzel, Sebastien; Scheitrum, Glenn; Schibler, Emilie; Schindler, Rafe; Schlösser, Markus; Schlueter, Ross D.; Schmid, Peter; Schmidt, Ringo Sebastian; Schneekloth, Uwe; Schreiber, Heinz Juergen; Schreiber, Siegfried; Schroeder, Henning; Peter Schüler, K.; Schulte, Daniel; Schultz-Coulon, Hans-Christian; Schumacher, Markus; Schumann, Steffen; Schumm, Bruce A.; Schwienhorst, Reinhard; Schwierz, Rainer; Scott, Duncan J.; Scuri, Fabrizio; Sefkow, Felix; Sefri, Rachid; Seguin-Moreau, Nathalie; Seidel, Sally; Seidman, David; Sekmen, Sezen; Seletskiy, Sergei; Senaha, Eibun; Senanayake, Rohan; Sendai, Hiroshi; Sertore, Daniele; Seryi, Andrei; Settles, Ronald; Sever, Ramazan; Shales, Nicholas; Shao, Ming; Shelkov, G.A.; Shepard, Ken; Shepherd-Themistocleous, Claire; Sheppard, John C.; Shi, Cai Tu; Shidara, Tetsuo; Shim, Yeo-Jeong; Shimizu, Hirotaka; Shimizu, Yasuhiro; Shimizu, Yuuki; Shimogawa, Tetsushi; Shin, Seunghwan; Shioden, Masaomi; Shipsey, Ian; Shirkov, Grigori; Shishido, Toshio; Shivpuri, Ram K.; Shrivastava, Purushottam; Shulga, Sergey; Shumeiko, Nikolai; Shuvalov, Sergey; Si, Zongguo; Siddiqui, Azher Majid; Siegrist, James; Simon, Claire; Simrock, Stefan; Sinev, Nikolai; Singh, Bhartendu K.; Singh, Jasbir; Singh, Pitamber; Singh, R.K.; Singh, S.K.; Singini, Monito; Sinha, Anil K.; Sinha, Nita; Sinha, Rahul; Sinram, Klaus; Sissakian, A.N.; Skachkov, N.B.; Skrinsky, Alexander; Slater, Mark; Slominski, Wojciech; Smiljanic, Ivan; Smith, A J Stewart; Smith, Alex; Smith, Brian J.; Smith, Jeff; Smith, Jonathan; Smith, Steve; Smith, Susan; Smith, Tonee; Neville Snodgrass, W.; Sobloher, Blanka; Sohn, Young-Uk; Solidum, Ruelson; Solyak, Nikolai; Son, Dongchul; Sonmez, Nasuf; Sopczak, Andre; Soskov, V.; Spencer, Cherrill M.; Spentzouris, Panagiotis; Speziali, Valeria; Spira, Michael; Sprehn, Daryl; Sridhar, K.; Srivastava, Asutosh; St. Lorant, Steve; Stahl, Achim; Stanek, Richard P.; Stanitzki, Marcel; Stanley, Jacob; Stefanov, Konstantin; Stein, Werner; Steiner, Herbert; Stenlund, Evert; Stern, Amir; Sternberg, Matt; Stockinger, Dominik; Stockton, Mark; Stoeck, Holger; Strachan, John; Strakhovenko, V.; Strauss, Michael; Striganov, Sergei I.; Strologas, John; Strom, David; Strube, Jan; Stupakov, Gennady; Su, Dong; Sudo, Yuji; Suehara, Taikan; Suehiro, Toru; Suetsugu, Yusuke; Sugahara, Ryuhei; Sugimoto, Yasuhiro; Sugiyama, Akira; Suh, Jun Suhk; Sukovic, Goran; Sun, Hong; Sun, Stephen; Sun, Werner; Sun, Yi; Sun, Yipeng; Suszycki, Leszek; Sutcliffe, Peter; Suthar, Rameshwar L.; Suwada, Tsuyoshi; Suzuki, Atsuto; Suzuki, Chihiro; Suzuki, Shiro; Suzuki, Takashi; Swent, Richard; Swientek, Krzysztof; Swinson, Christina; Syresin, Evgeny; Szleper, Michal; Tadday, Alexander; Takahashi, Rika; Takahashi, Tohru; Takano, Mikio; Takasaki, Fumihiko; Takeda, Seishi; Takenaka, Tateru; Takeshita, Tohru; Takubo, Yosuke; Tanaka, Masami; Tang, Chuan Xiang; Taniguchi, Takashi; Tantawi, Sami; Tapprogge, Stefan; Tartaglia, Michael A.; Tassielli, Giovanni Francesco; Tauchi, Toshiaki; Tavian, Laurent; Tawara, Hiroko; Taylor, Geoffrey; Telnov, Alexandre V.; Telnov, Valery; Tenenbaum, Peter; Teodorescu, Eliza; Terashima, Akio; Terracciano, Giuseppina; Terunuma, Nobuhiro; Teubner, Thomas; Teuscher, Richard; Theilacker, Jay; Thomson, Mark; Tice, Jeff; Tigner, Maury; Timmermans, Jan; Titov, Maxim; Toge, Nobukazu; Tokareva, N.A.; Tollefson, Kirsten; Tomasek, Lukas; Tomovic, Savo; Tompkins, John; Tonutti, Manfred; Topkar, Anita; Toprek, Dragan; Toral, Fernando; Torrence, Eric; Traversi, Gianluca; Trimpl, Marcel; Mani Tripathi, S.; Trischuk, William; Trodden, Mark; Trubnikov, G.V.; Tschirhart, Robert; Tskhadadze, Edisher; Tsuchiya, Kiyosumi; Tsukamoto, Toshifumi; Tsunemi, Akira; Tucker, Robin; Turchetta, Renato; Tyndel, Mike; Uekusa, Nobuhiro; Ueno, Kenji; Umemori, Kensei; Ummenhofer, Martin; Underwood, David; Uozumi, Satoru; Urakawa, Junji; Urban, Jeremy; Uriot, Didier; Urner, David; Ushakov, Andrei; Usher, Tracy; Uzunyan, Sergey; Vachon, Brigitte; Valerio, Linda; Valin, Isabelle; Valishev, Alex; Vamra, Raghava; Van der Graaf, Harry; Van Kooten, Rick; Van Zandbergen, Gary; Vanel, Jean-Charles; Variola, Alessandro; Varner, Gary; Velasco, Mayda; Velte, Ulrich; Velthuis, Jaap; Vempati, Sundir K.; Venturini, Marco; Vescovi, Christophe; Videau, Henri; Vila, Ivan; Vincent, Pascal; Virey, Jean-Marc; Visentin, Bernard; Viti, Michele; Vo, Thanh Cuong; Vogel, Adrian; Vogt, Harald; von Toerne, Eckhard; Vorozhtsov, S.B.; Vos, Marcel; Votava, Margaret; Vrba, Vaclav; Wackeroth, Doreen; Wagner, Albrecht; Wagner, Carlos E.M.; Wagner, Stephen; Wake, Masayoshi; Walczak, Roman; Walker, Nicholas J.; Walkowiak, Wolfgang; Wallon, Samuel; Walsh, Roberval; Walston, Sean; Waltenberger, Wolfgang; Walz, Dieter; Wang, Chao En; Wang, Chun Hong; Wang, Dou; Wang, Faya; Wang, Guang Wei; Wang, Haitao; Wang, Jiang; Wang, Jiu Qing; Wang, Juwen; Wang, Lanfa; Wang, Lei; Wang, Min-Zu; Wang, Qing; Wang, Shu Hong; Wang, Xiaolian; Wang, Xue-Lei; Wang, Yi Fang; Wang, Zheng; Wanzenberg, Rainer; Ward, Bennie; Ward, David; Warmbein, Barbara; Warner, David W.; Warren, Matthew; Washio, Masakazu; Watanabe, Isamu; Watanabe, Ken; Watanabe, Takashi; Watanabe, Yuichi; Watson, Nigel; Wattimena, Nanda; Wayne, Mitchell; Weber, Marc; Weerts, Harry; Weiglein, Georg; Weiland, Thomas; Weinzierl, Stefan; Weise, Hans; Weisend, John; Wendt, Manfred; Wendt, Oliver; Wenzel, Hans; Wenzel, William A.; Wermes, Norbert; Werthenbach, Ulrich; Wesseln, Steve; Wester, William; White, Andy; White, Glen R.; Wichmann, Katarzyna; Wienemann, Peter; Wierba, Wojciech; Wilksen, Tim; Willis, William; Wilson, Graham W.; Wilson, John A.; Wilson, Robert; Wing, Matthew; Winter, Marc; Wirth, Brian D.; Wolbers, Stephen A.; Wolff, Dan; Wolski, Andrzej; Woodley, Mark D.; Woods, Michael; Woodward, Michael L.; Woolliscroft, Timothy; Worm, Steven; Wormser, Guy; Wright, Dennis; Wright, Douglas; Wu, Andy; Wu, Tao; Wu, Yue Liang; Xella, Stefania; Xia, Guoxing; Xia, Lei; Xiao, Aimin; Xiao, Liling; Xie, Jia Lin; Xing, Zhi-Zhong; Xiong, Lian You; Xu, Gang; Xu, Qing Jing; Yajnik, Urjit A.; Yakimenko, Vitaly; Yamada, Ryuji; Yamaguchi, Hiroshi; Yamamoto, Akira; Yamamoto, Hitoshi; Yamamoto, Masahiro; Yamamoto, Naoto; Yamamoto, Richard; Yamamoto, Yasuchika; Yamanaka, Takashi; Yamaoka, Hiroshi; Yamashita, Satoru; Yamazaki, Hideki; Yan, Wenbiao; Yang, Hai-Jun; Yang, Jin Min; Yang, Jongmann; Yang, Zhenwei; Yano, Yoshiharu; Yazgan, Efe; Yeh, G.P.; Yilmaz, Hakan; Yock, Philip; Yoda, Hakutaro; Yoh, John; Yokoya, Kaoru; Yokoyama, Hirokazu; York, Richard C.; Yoshida, Mitsuhiro; Yoshida, Takuo; Yoshioka, Tamaki; Young, Andrew; Yu, Cheng Hui; Yu, Jaehoon; Yu, Xian Ming; Yuan, Changzheng; Yue, Chong-Xing; Yue, Jun Hui; Zacek, Josef; Zagorodnov, Igor; Zalesak, Jaroslav; Zalikhanov, Boris; Zarnecki, Aleksander Filip; Zawiejski, Leszek; Zeitnitz, Christian; Zeller, Michael; Zerwas, Dirk; Zerwas, Peter; Zeyrek, Mehmet; Zhai, Ji Yuan; Zhang, Bao Cheng; Zhang, Bin; Zhang, Chuang; Zhang, He; Zhang, Jiawen; Zhang, Jing; Zhang, Jing Ru; Zhang, Jinlong; Zhang, Liang; Zhang, X.; Zhang, Yuan; Zhang, Zhige; Zhang, Zhiqing; Zhang, Ziping; Zhao, Haiwen; Zhao, Ji Jiu; Zhao, Jing Xia; Zhao, Ming Hua; Zhao, Sheng Chu; Zhao, Tianchi; Zhao, Tong Xian; Zhao, Zhen Tang; Zhao, Zhengguo; Zhou, De Min; Zhou, Feng; Zhou, Shun; Zhu, Shou Hua; Zhu, Xiong Wei; Zhukov, Valery; Zimmermann, Frank; Ziolkowski, Michael; Zisman, Michael S.; Zomer, Fabian; Zong, Zhang Guo; Zorba, Osman; Zutshi, Vishnu

    2007-01-01

    This report, Volume IV of the International Linear Collider Reference Design Report, describes the detectors which will record and measure the charged and neutral particles produced in the ILC's high energy e+e- collisions. The physics of the ILC, and the environment of the machine-detector interface, pose new challenges for detector design. Several conceptual designs for the detector promise the needed performance, and ongoing detector R&D is addressing the outstanding technological issues. Two such detectors, operating in push-pull mode, perfectly instrument the ILC interaction region, and access the full potential of ILC physics.

  3. Mooring Design for the Floating Oscillating Water Column Reference Model

    Energy Technology Data Exchange (ETDEWEB)

    Brefort, Dorian [Univ. of Michigan, Ann Arbor, MI (United States); Bull, Diana L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-09-01

    To reduce the price of the reference Backward Bent Duct Buoy (BBDB), a study was done analyzing the effects of reducing the mooring line length, and a new mooring design was developed. It was found that the overall length of the mooring lines could be reduced by 1290 meters, allowing a significant price reduction of the system. In this paper, we will first give a description of the model and the storm environment it will be subject to. We will then give a recommendation for the new mooring system, followed by a discussion of the severe weather simulation results, and an analysis of the conservative and aggressive aspects of the design.

  4. Automotive Stirling reference engine design report

    Science.gov (United States)

    1981-01-01

    The reference Stirling engine system is described which provides the best possible fuel economy while meeting or exceeding all other program objectives. The system was designed to meet the requirements of a 1984 Pontiac Phoenix (X-body). This design utilizes all new technology that can reasonably be expected to be developed by 1984 and that is judged to provide significant improvement, relative to development risk and cost. Topics covered include: (1) external heat system; (2) hot engine system; (3) cold engine system; (4) engine drive system; (5) power control system and auxiliaries; (6) engine instalation; (7) optimization and vehicle simulation; (8) engine materials; and (9) production cost analysis.

  5. Reference Model 2: "Rev 0" Rotor Design

    Energy Technology Data Exchange (ETDEWEB)

    Barone, Matthew F. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Berg, Jonathan Charles [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Griffith, Daniel [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2011-12-01

    The preliminary design for a three-bladed cross-flow rotor for a reference marine hydrokinetic turbine is presented. A rotor performance design code is described, along with modifications to the code to allow prediction of blade support strut drag as well as interference between two counter-rotating rotors. The rotor is designed to operate in a reference site corresponding to a riverine environment. Basic rotor performance and rigid-body loads calculations are performed to size the rotor elements and select the operating speed range. The preliminary design is verified with a simple finite element model that provides estimates of bending stresses during operation. A concept for joining the blades and support struts is developed and analyzed with a separate finite element analysis. Rotor mass, production costs, and annual energy capture are estimated in order to allow calculations of system cost-of-energy. Evaluation Only. Created with Aspose.Pdf.Kit. Copyright 2002-2011 Aspose Pty Ltd Evaluation Only. Created with Aspose.Pdf.Kit. Copyright 2002-2011 Aspose Pty Ltd

  6. ILC Reference Design Report Volume 3 - Accelerator

    CERN Document Server

    Phinney, Nan; Walker, Nicholas J.; Aarons, Gerald; Abe, Toshinori; Abernathy, Jason; Ablikim, Medina; Abramowicz, Halina; Adey, David; Adloff, Catherine; Adolphsen, Chris; Afanaciev, Konstantin; Agapov, Ilya; Ahn, Jung-Keun; Aihara, Hiroaki; Akemoto, Mitsuo; del Carmen Alabau, Maria; Albert, Justin; Albrecht, Hartwig; Albrecht, Michael; Alesini, David; Alexander, Gideon; Alexander, Jim; Allison, Wade; Amann, John; Amirikas, Ramila; An, Qi; Anami, Shozo; Ananthanarayan, B.; Anderson, Terry; Andricek, Ladislav; Anduze, Marc; Anerella, Michael; Anfimov, Nikolai; Angal-Kalinin, Deepa; Antipov, Sergei; Antoine, Claire; Aoki, Mayumi; Aoza, Atsushi; Aplin, Steve; Appleby, Rob; Arai, Yasuo; Araki, Sakae; Arkan, Tug; Arnold, Ned; Arnold, Ray; Arnowitt, Richard; Artru, Xavier; Arya, Kunal; Aryshev, Alexander; Asakawa, Eri; Asiri, Fred; Asner, David; Atac, Muzaffer; Atoian, Grigor; Attié, David; Augustin, Jean-Eudes; Augustine, David B.; Ayres, Bradley; Aziz, Tariq; Baars, Derek; Badaud, Frederique; Baddams, Nigel; Bagger, Jonathan; Bai, Sha; Bailey, David; Bailey, Ian R.; Baker, David; Balalykin, Nikolai I.; Balbuena, Juan Pablo; Baldy, Jean-Luc; Ball, Markus; Ball, Maurice; Ballestrero, Alessandro; Ballin, Jamie; Baltay, Charles; Bambade, Philip; Ban, Syuichi; Band, Henry; Bane, Karl; Banerjee, Bakul; Barbanotti, Serena; Barbareschi, Daniele; Barbaro-Galtieri, Angela; Barber, Desmond P.; Barbi, Mauricio; Bardin, Dmitri Y.; Barish, Barry; Barklow, Timothy L.; Barlow, Roger; Barnes, Virgil E.; Barone, Maura; Bartels, Christoph; Bartsch, Valeria; Basu, Rahul; Battaglia, Marco; Batygin, Yuri; Baudot, Jerome; Baur, Ulrich; Elwyn Baynham, D.; Beard, Carl; Bebek, Chris; Bechtle, Philip; Becker, Ulrich J.; Bedeschi, Franco; Bedjidian, Marc; Behera, Prafulla; Behnke, Ties; Bellantoni, Leo; Bellerive, Alain; Bellomo, Paul; Bentson, Lynn D.; Benyamna, Mustapha; Bergauer, Thomas; Berger, Edmond; Bergholz, Matthias; Beri, Suman; Berndt, Martin; Bernreuther, Werner; Bertolini, Alessandro; Besancon, Marc; Besson, Auguste; Beteille, Andre; Bettoni, Simona; Beyer, Michael; Bhandari, R.K.; Bharadwaj, Vinod; Bhatnagar, Vipin; Bhattacharya, Satyaki; Bhattacharyya, Gautam; Bhattacherjee, Biplob; Bhuyan, Ruchika; Bi, Xiao-Jun; Biagini, Marica; Bialowons, Wilhelm; Biebel, Otmar; Bieler, Thomas; Bierwagen, John; Birch, Alison; Bisset, Mike; Biswal, S.S.; Blackmore, Victoria; Blair, Grahame; Blanchard, Guillaume; Blazey, Gerald; Blue, Andrew; Blümlein, Johannes; Boffo, Christian; Bohn, Courtlandt; Boiko, V.I.; Boisvert, Veronique; Bondarchuk, Eduard N.; Boni, Roberto; Bonvicini, Giovanni; Boogert, Stewart; Boonekamp, Maarten; Boorman, Gary; Borras, Kerstin; Bortoletto, Daniela; Bosco, Alessio; Bosio, Carlo; Bosland, Pierre; Bosotti, Angelo; Boudry, Vincent; Boumediene, Djamel-Eddine; Bouquet, Bernard; Bourov, Serguei; Bowden, Gordon; Bower, Gary; Boyarski, Adam; Bozovic-Jelisavcic, Ivanka; Bozzi, Concezio; Brachmann, Axel; Bradshaw, Tom W.; Brandt, Andrew; Brasser, Hans Peter; Brau, Benjamin; Brau, James E.; Breidenbach, Martin; Bricker, Steve; Brient, Jean-Claude; Brock, Ian; Brodsky, Stanley; Brooksby, Craig; Broome, Timothy A.; Brown, David; Brown, David; Brownell, James H.; Bruchon, Mélanie; Brueck, Heiner; Brummitt, Amanda J.; Brun, Nicole; Buchholz, Peter; Budagov, Yulian A.; Bulgheroni, Antonio; Bulyak, Eugene; Bungau, Adriana; Bürger, Jochen; Burke, Dan; Burkhart, Craig; Burrows, Philip; Burt, Graeme; Burton, David; Büsser, Karsten; Butler, John; Butterworth, Jonathan; Buzulutskov, Alexei; Cabruja, Enric; Caccia, Massimo; Cai, Yunhai; Calcaterra, Alessandro; Caliier, Stephane; Camporesi, Tiziano; Cao, Jun-Jie; Cao, J.S.; Capatina, Ofelia; Cappellini, Chiara; Carcagno, Ruben; Carena, Marcela; Carloganu, Cristina; Carosi, Roberto; Stephen Carr, F.; Carrion, Francisco; Carter, Harry F.; Carter, John; Carwardine, John; Cassel, Richard; Cassell, Ronald; Cavallari, Giorgio; Cavallo, Emanuela; Cembranos, Jose A.R.; Chakraborty, Dhiman; Chandez, Frederic; Charles, Matthew; Chase, Brian; Chattopadhyay, Subhasis; Chauveau, Jacques; Chefdeville, Maximilien; Chehab, Robert; Chel, Stéphane; Chelkov, Georgy; Chen, Chiping; Chen, He Sheng; Chen, Huai Bi; Chen, Jia Er; Chen, Sen Yu; Chen, Shaomin; Chen, Shenjian; Chen, Xun; Chen, Yuan Bo; Cheng, Jian; Chevallier, M.; Chi, Yun Long; Chickering, William; Cho, Gi-Chol; Cho, Moo-Hyun; Choi, Jin-Hyuk; Choi, Jong Bum; Choi, Seong Youl; Choi, Young-Il; Choudhary, Brajesh; Choudhury, Debajyoti; Rai Choudhury, S.; Christian, David; Christian, Glenn; Christophe, Grojean; Chung, Jin-Hyuk; Church, Mike; Ciborowski, Jacek; Cihangir, Selcuk; Ciovati, Gianluigi; Clarke, Christine; Clarke, Don G.; Clarke, James A.; Clements, Elizabeth; Coca, Cornelia; Coe, Paul; Cogan, John; Colas, Paul; Collard, Caroline; Colledani, Claude; Combaret, Christophe; Comerma, Albert; Compton, Chris; Constance, Ben; Conway, John; Cook, Ed; Cooke, Peter; Cooper, William; Corcoran, Sean; Cornat, Rémi; Corner, Laura; Cortina Gil, Eduardo; Clay Corvin, W.; Cotta Ramusino, Angelo; Cowan, Ray; Crawford, Curtis; Cremaldi, Lucien M; Crittenden, James A.; Cussans, David; Cvach, Jaroslav; da Silva, Wilfrid; Dabiri Khah, Hamid; Dabrowski, Anne; Dabrowski, Wladyslaw; Dadoun, Olivier; Dai, Jian Ping; Dainton, John; Daly, Colin; Damerell, Chris; Danilov, Mikhail; Daniluk, Witold; Daram, Sarojini; Datta, Anindya; Dauncey, Paul; David, Jacques; Davier, Michel; Davies, Ken P.; Dawson, Sally; De Boer, Wim; De Curtis, Stefania; De Groot, Nicolo; de la Taille, Christophe; de Lira, Antonio; De Roeck, Albert; de Sangro, Riccardo; De Santis,Stefano; Deacon, Laurence; Deandrea, Aldo; Dehmelt, Klaus; Delagnes, Eric; Delahaye, Jean-Pierre; Delebecque, Pierre; Delerue, Nicholas; Delferriere, Olivier; Demarteau, Marcel; Deng, Zhi; Denisov, Yu.N.; Densham, Christopher J.; Desch, Klaus; Deshpande, Nilendra; Devanz, Guillaume; Devetak, Erik; Dexter, Amos; Di benedetto, Vito; Diéguez, Angel; Diener, Ralf; Dinh, Nguyen Dinh; Dixit, Madhu; Dixit, Sudhir; Djouadi, Abdelhak; Dolezal, Zdenek; Dollan, Ralph; Dong, Dong; Dong, Hai Yi; Dorfan, Jonathan; Dorokhov, Andrei; Doucas, George; Downing, Robert; Doyle, Eric; Doziere, Guy; Drago, Alessandro; Dragt, Alex; Drake, Gary; Drásal, Zbynek; Dreiner, Herbert; Drell, Persis; Driouichi, Chafik; Drozhdin, Alexandr; Drugakov, Vladimir; Du, Shuxian; Dugan, Gerald; Duginov, Viktor; Dulinski, Wojciech; Dulucq, Frederic; Dutta, Sukanta; Dwivedi, Jishnu; Dychkant, Alexandre; Dzahini, Daniel; Eckerlin, Guenter; Edwards, Helen; Ehrenfeld, Wolfgang; Ehrlichman, Michael; Ehrlichmann, Heiko; Eigen, Gerald; Elagin, Andrey; Elementi, Luciano; Eliasson, Peder; Ellis, John; Ellwood, George; Elsen, Eckhard; Emery, Louis; Enami, Kazuhiro; Endo, Kuninori; Enomoto, Atsushi; Eozénou, Fabien; Erbacher, Robin; Erickson, Roger; Oleg Eyser, K.; Fadeyev, Vitaliy; Fang, Shou Xian; Fant, Karen; Fasso, Alberto; Faucci Giannelli, Michele; Fehlberg, John; Feld, Lutz; Feng, Jonathan L.; Ferguson, John; Fernandez-Garcia, Marcos; Luis Fernandez-Hernando, J.; Fiala, Pavel; Fieguth, Ted; Finch, Alexander; Finocchiaro, Giuseppe; Fischer, Peter; Fisher, Peter; Eugene Fisk, H.; Fitton, Mike D.; Fleck, Ivor; Fleischer, Manfred; Fleury, Julien; Flood, Kevin; Foley, Mike; Ford, Richard; Fortin, Dominique; Foster, Brian; Fourches, Nicolas; Francis, Kurt; Frey, Ariane; Frey, Raymond; Friedsam, Horst; Frisch, Josef; Frishman, Anatoli; Fuerst, Joel; Fujii, Keisuke; Fujimoto, Junpei; Fukuda, Masafumi; Fukuda, Shigeki; Funahashi, Yoshisato; Funk, Warren; Furletova, Julia; Furukawa, Kazuro; Furuta, Fumio; Fusayasu, Takahiro; Fuster, Juan; Gadow, Karsten; Gaede, Frank; Gaglione, Renaud; Gai, Wei; Gajewski, Jan; Galik, Richard; Galkin, Alexei; Galkin, Valery; Gallin-Martel, Laurent; Gannaway, Fred; Gao, Jian She; Gao, Jie; Gao, Yuanning; Garbincius, Peter; Garcia-Tabares, Luis; Garren, Lynn; Garrido, Luís; Garutti, Erika; Garvey, Terry; Garwin, Edward; Gascón, David; Gastal, Martin; Gatto, Corrado; Gatto, Raoul; Gay, Pascal; Ge, Lixin; Ge, Ming Qi; Ge, Rui; Geiser, Achim; Gellrich, Andreas; Genat, Jean-Francois; Geng, Zhe Qiao; Gentile, Simonetta; Gerbick, Scot; Gerig, Rod; Ghosh, Dilip Kumar; Ghosh, Kirtiman; Gibbons, Lawrence; Giganon, Arnaud; Gillespie, Allan; Gillman, Tony; Ginzburg, Ilya; Giomataris, Ioannis; Giunta, Michele; Gladkikh, Peter; Gluza, Janusz; Godbole, Rohini; Godfrey, Stephen; Goldhaber, Gerson; Goldstein, Joel; Gollin, George D.; Gonzalez-Sanchez, Francisco Javier; Goodrick, Maurice; Gornushkin, Yuri; Gostkin, Mikhail; Gottschalk, Erik; Goudket, Philippe; Gough Eschrich, Ivo; Gournaris, Filimon; Graciani, Ricardo; Graf, Norman; Grah, Christian; Grancagnolo, Francesco; Grandjean, Damien; Grannis, Paul; Grassellino, Anna; Graugés, Eugeni; Gray, Stephen; Green, Michael; Greenhalgh, Justin; Greenshaw, Timothy; Grefe, Christian; Gregor, Ingrid-Maria; Grenier, Gerald; Grimes, Mark; Grimm, Terry; Gris, Philippe; Grivaz, Jean-Francois; Groll, Marius; Gronberg, Jeffrey; Grondin, Denis; Groom, Donald; Gross, Eilam; Grunewald, Martin; Grupen, Claus; Grzelak, Grzegorz; Gu, Jun; Gu, Yun-Ting; Guchait, Monoranjan; Guiducci, Susanna; Guler, Ali Murat; Guler, Hayg; Gulmez, Erhan; Gunion, John; Guo, Zhi Yu; Gurtu, Atul; Ha, Huy Bang; Haas, Tobias; Haase, Andy; Haba, Naoyuki; Haber, Howard; Haensel, Stephan; Hagge, Lars; Hagura, Hiroyuki; Hajdu, Csaba; Haller, Gunther; Haller, Johannes; Hallermann, Lea; Halyo, Valerie; Hamaguchi, Koichi; Hammond, Larry; Han, Liang; Han, Tao; Hand, Louis; Handu, Virender K.; Hano, Hitoshi; Hansen, Christian; Hansen, Jørn Dines; Hansen, Jorgen Beck; Hara, Kazufumi; Harder, Kristian; Hartin, Anthony; Hartung, Walter; Hast, Carsten; Hauptman, John; Hauschild, Michael; Hauviller, Claude; Havranek, Miroslav; Hawkes, Chris; Hawkings, Richard; Hayano, Hitoshi; Hazumi, Masashi; He, An; He, Hong Jian; Hearty, Christopher; Heath, Helen; Hebbeker, Thomas; Hedberg, Vincent; Hedin, David; Heifets, Samuel; Heinemeyer, Sven; Heini, Sebastien; Helebrant, Christian; Helms, Richard; Heltsley, Brian; Henrot-Versille, Sophie; Henschel, Hans; Hensel, Carsten; Hermel, Richard; Herms, Atilà; Herten, Gregor; Hesselbach, Stefan; Heuer, Rolf-Dieter; Heusch, Clemens A.; Hewett, Joanne; Higashi, Norio; Higashi, Takatoshi; Higashi, Yasuo; Higo, Toshiyasu; Hildreth, Michael D.; Hiller, Karlheinz; Hillert, Sonja; Hillier, Stephen James; Himel, Thomas; Himmi, Abdelkader; Hinchliffe, Ian; Hioki, Zenro; Hirano, Koichiro; Hirose, Tachishige; Hisamatsu, Hiromi; Hisano, Junji; Hlaing, Chit Thu; Hock, Kai Meng; Hoeferkamp, Martin; Hohlfeld, Mark; Honda, Yousuke; Hong, Juho; Hong, Tae Min; Honma, Hiroyuki; Horii, Yasuyuki; Horvath, Dezso; Hosoyama, Kenji; Hostachy, Jean-Yves; Hou, Mi; Hou, Wei-Shu; Howell, David; Hronek, Maxine; Hsiung, Yee B.; Hu, Bo; Hu, Tao; Huang, Jung-Yun; Huang, Tong Ming; Huang, Wen Hui; Huedem, Emil; Huggard, Peter; Hugonie, Cyril; Hu-Guo, Christine; Huitu, Katri; Hwang, Youngseok; Idzik, Marek; Ignatenko, Alexandr; Ignatov, Fedor; Ikeda, Hirokazu; Ikematsu, Katsumasa; Ilicheva, Tatiana; Imbault, Didier; Imhof, Andreas; Incagli, Marco; Ingbir, Ronen; Inoue, Hitoshi; Inoue, Youichi; Introzzi, Gianluca; Ioakeimidi, Katerina; Ishihara, Satoshi; Ishikawa, Akimasa; Ishikawa, Tadashi; Issakov, Vladimir; Ito, Kazutoshi; Ivanov, V.V.; Ivanov, Valentin; Ivanyushenkov, Yury; Iwasaki, Masako; Iwashita, Yoshihisa; Jackson, David; Jackson, Frank; Jacobsen, Bob; Jaganathan, Ramaswamy; Jamison, Steven; Janssen, Matthias Enno; Jaramillo-Echeverria, Richard; Jaros, John; Jauffret, Clement; Jawale, Suresh B.; Jeans, Daniel; Jedziniak, Ron; Jeffery, Ben; Jehanno, Didier; Jenner, Leo J.; Jensen, Chris; Jensen, David R.; Jiang, Hairong; Jiang, Xiao Ming; Jimbo, Masato; Jin, Shan; Keith Jobe, R.; Johnson, Anthony; Johnson, Erik; Johnson, Matt; Johnston, Michael; Joireman, Paul; Jokic, Stevan; Jones, James; Jones, Roger M.; Jongewaard, Erik; Jönsson, Leif; Joshi, Gopal; Joshi, Satish C.; Jung, Jin-Young; Junk, Thomas; Juste, Aurelio; Kado, Marumi; Kadyk, John; Käfer, Daniela; Kako, Eiji; Kalavase, Puneeth; Kalinin, Alexander; Kalinowski, Jan; Kamitani, Takuya; Kamiya, Yoshio; Kamiya, Yukihide; Kamoshita, Jun-ichi; Kananov, Sergey; Kanaya, Kazuyuki; Kanazawa, Ken-ichi; Kanemura, Shinya; Kang, Heung-Sik; Kang, Wen; Kanjial, D.; Kapusta, Frédéric; Karataev, Pavel; Karchin, Paul E.; Karlen, Dean; Karyotakis, Yannis; Kashikhin, Vladimir; Kashiwagi, Shigeru; Kasley, Paul; Katagiri, Hiroaki; Kato, Takashi; Kato, Yukihiro; Katzy, Judith; Kaukher, Alexander; Kaur, Manjit; Kawagoe, Kiyotomo; Kawamura, Hiroyuki; Kazakov, Sergei; Kekelidze, V.D.; Keller, Lewis; Kelley, Michael; Kelly, Marc; Kelly, Michael; Kennedy, Kurt; Kephart, Robert; Keung, Justin; Khainovski, Oleg; Khan, Sameen Ahmed; Khare, Prashant; Khovansky, Nikolai; Kiesling, Christian; Kikuchi, Mitsuo; Kilian, Wolfgang; Killenberg, Martin; Kim, Donghee; Kim, Eun San; Kim, Eun-Joo; Kim, Guinyun; Kim, Hongjoo; Kim, Hyoungsuk; Kim, Hyun-Chui; Kim, Jonghoon; Kim, Kwang-Je; Kim, Kyung Sook; Kim, Peter; Kim, Seunghwan; Kim, Shin-Hong; Kim, Sun Kee; Kim, Tae Jeong; Kim, Youngim; Kim, Young-Kee; Kimmitt, Maurice; Kirby, Robert; Kircher, François; Kisielewska, Danuta; Kittel, Olaf; Klanner, Robert; Klebaner, Arkadiy L.; Kleinwort, Claus; Klimkovich, Tatsiana; Klinkby, Esben; Kluth, Stefan; Knecht, Marc; Kneisel, Peter; Ko, In Soo; Ko, Kwok; Kobayashi, Makoto; Kobayashi, Nobuko; Kobel, Michael; Koch, Manuel; Kodys, Peter; Koetz, Uli; Kohrs, Robert; Kojima, Yuuji; Kolanoski, Hermann; Kolodziej, Karol; Kolomensky, Yury G.; Komamiya, Sachio; Kong, Xiang Cheng; Konigsberg, Jacobo; Korbel, Volker; Koscielniak, Shane; Kostromin, Sergey; Kowalewski, Robert; Kraml, Sabine; Krammer, Manfred; Krasnykh, Anatoly; Krautscheid, Thorsten; Krawczyk, Maria; James Krebs, H.; Krempetz, Kurt; Kribs, Graham; Krishnagopal, Srinivas; Kriske, Richard; Kronfeld, Andreas; Kroseberg, Jürgen; Kruchonak, Uladzimir; Kruecker, Dirk; Krüger, Hans; Krumpa, Nicholas A.; Krumshtein, Zinovii; Kuang, Yu Ping; Kubo, Kiyoshi; Kuchler, Vic; Kudoh, Noboru; Kulis, Szymon; Kumada, Masayuki; Kumar, Abhay; Kume, Tatsuya; Kundu, Anirban; Kurevlev, German; Kurihara, Yoshimasa; Kuriki, Masao; Kuroda, Shigeru; Kuroiwa, Hirotoshi; Kurokawa, Shin-ichi; Kusano, Tomonori; Kush, Pradeep K.; Kutschke, Robert; Kuznetsova, Ekaterina; Kvasnicka, Peter; Kwon, Youngjoon; Labarga, Luis; Lacasta, Carlos; Lackey, Sharon; Lackowski, Thomas W.; Lafaye, Remi; Lafferty, George; Lagorio, Eric; Laktineh, Imad; Lal, Shankar; Laloum, Maurice; Lam, Briant; Lancaster, Mark; Lander, Richard; Lange, Wolfgang; Langenfeld, Ulrich; Langeveld, Willem; Larbalestier, David; Larsen, Ray; Lastovicka, Tomas; Lastovicka-Medin, Gordana; Latina, Andrea; Latour, Emmanuel; Laurent, Lisa; Le, Ba Nam; Le, Duc Ninh; Le Diberder, Francois; Dû, Patrick Le; Lebbolo, Hervé; Lebrun, Paul; Lecoq, Jacques; Lee, Sung-Won; Lehner, Frank; Leibfritz, Jerry; Lenkszus, Frank; Lesiak, Tadeusz; Levy, Aharon; Lewandowski, Jim; Leyh, Greg; Li, Cheng; Li, Chong Sheng; Li, Chun Hua; Li, Da Zhang; Li, Gang; Li, Jin; Li, Shao Peng; Li, Wei Ming; Li, Weiguo; Li, Xiao Ping; Li, Xue-Qian; Li, Yuanjing; Li, Yulan; Li, Zenghai; Li, Zhong Quan; Liang, Jian Tao; Liao, Yi; Lilje, Lutz; Guilherme Lima, J.; Lintern, Andrew J.; Lipton, Ronald; List, Benno; List, Jenny; Liu, Chun; Liu, Jian Fei; Liu, Ke Xin; Liu, Li Qiang; Liu, Shao Zhen; Liu, Sheng Guang; Liu, Shubin; Liu, Wanming; Liu, Wei Bin; Liu, Ya Ping; Liu, Yu Dong; Lockyer, Nigel; Logan, Heather E.; Logatchev, Pavel V.; Lohmann, Wolfgang; Lohse, Thomas; Lola, Smaragda; Lopez-Virto, Amparo; Loveridge, Peter; Lozano, Manuel; Lu, Cai-Dian; Lu, Changguo; Lu, Gong-Lu; Lu, Wen Hui; Lubatti, Henry; Lucotte, Arnaud; Lundberg, Björn; Lundin, Tracy; Luo, Mingxing; Luong, Michel; Luth, Vera; Lutz, Benjamin; Lutz, Pierre; Lux, Thorsten; Luzniak, Pawel; Lyapin, Alexey; Lykken, Joseph; Lynch, Clare; Ma, Li; Ma, Lili; Ma, Qiang; Ma, Wen-Gan; Macfarlane, David; Maciel, Arthur; MacLeod, Allan; MacNair, David; Mader, Wolfgang; Magill, Stephen; Magnan, Anne-Marie; Maiheu, Bino; Maity, Manas; Majchrzak, Millicent; Majumder, Gobinda; Makarov, Roman; Makowski, Dariusz; Malaescu, Bogdan; Mallik, C.; Mallik, Usha; Malton, Stephen; Malyshev, Oleg B.; Malysheva, Larisa I.; Mammosser, John; Mamta; Mamuzic, Judita; Manen, Samuel; Manghisoni, Massimo; Manly, Steven; Marcellini, Fabio; Marcisovsky, Michal; Markiewicz, Thomas W.; Marks, Steve; Marone, Andrew; Marti, Felix; Martin, Jean-Pierre; Martin, Victoria; Martin-Chassard, Gisèle; Martinez, Manel; Martinez-Rivero, Celso; Martsch, Dennis; Martyn, Hans-Ulrich; Maruyama, Takashi; Masuzawa, Mika; Mathez, Hervé; Matsuda, Takeshi; Matsumoto, Hiroshi; Matsumoto, Shuji; Matsumoto, Toshihiro; Matsunaga, Hiroyuki; Mättig, Peter; Mattison, Thomas; Mavromanolakis, Georgios; Mawatari, Kentarou; Mazzacane, Anna; McBride, Patricia; McCormick, Douglas; McCormick, Jeremy; McDonald, Kirk T.; McGee, Mike; McIntosh, Peter; McKee, Bobby; McPherson, Robert A.; Meidlinger, Mandi; Meier, Karlheinz; Mele, Barbara; Meller, Bob; Melzer-Pellmann, Isabell-Alissandra; Mendez, Hector; Mercer, Adam; Merkin, Mikhail; Meshkov, I.N.; Messner, Robert; Metcalfe, Jessica; Meyer, Chris; Meyer, Hendrik; Meyer, Joachim; Meyer, Niels; Meyners, Norbert; Michelato, Paolo; Michizono, Shinichiro; Mihalcea, Daniel; Mihara, Satoshi; Mihara, Takanori; Mikami, Yoshinari; Mikhailichenko, Alexander A.; Milardi, Catia; Miller, David J.; Miller, Owen; Miller, Roger J.; Milstene, Caroline; Mimashi, Toshihiro; Minashvili, Irakli; Miquel, Ramon; Mishra, Shekhar; Mitaroff, Winfried; Mitchell, Chad; Miura, Takako; Miyamoto, Akiya; Miyata, Hitoshi; Mjörnmark, Ulf; Mnich, Joachim; Moenig, Klaus; Moffeit, Kenneth; Mokhov, Nikolai; Molloy, Stephen; Monaco, Laura; Monasterio, Paul R.; Montanari, Alessandro; Moon, Sung Ik; Moortgat-Pick, Gudrid A.; Mora de Freitas, Paulo; Morel, Federic; Moretti, Stefano; Morgunov, Vasily; Mori, Toshinori; Morin, Laurent; Morisseau, François; Morita, Yoshiyuki; Morita, Youhei; Morita, Yuichi; Morozov, Nikolai; Morozumi, Yuichi; Morse, William; Moser, Hans-Guenther; Moultaka, Gilbert; Mtingwa, Sekazi; Mudrinic, Mihajlo; Mueller, Alex; Mueller, Wolfgang; Muennich, Astrid; Muhlleitner, Milada Margarete; Mukherjee, Bhaskar; Mukhopadhyaya, Biswarup; Müller, Thomas; Munro, Morrison; Murayama, Hitoshi; Muto, Toshiya; Myneni, Ganapati Rao; Nabhiraj, P.Y.; Nagaitsev, Sergei; Nagamine, Tadashi; Nagano, Ai; Naito, Takashi; Nakai, Hirotaka; Nakajima, Hiromitsu; Nakamura, Isamu; Nakamura, Tomoya; Nakanishi, Tsutomu; Nakao, Katsumi; Nakao, Noriaki; Nakayoshi, Kazuo; Nam, Sang; Namito, Yoshihito; Namkung, Won; Nantista, Chris; Napoly, Olivier; Narain, Meenakshi; Naroska, Beate; Nauenberg, Uriel; Nayyar, Ruchika; Neal, Homer; Nelson, Charles; Nelson, Janice; Nelson, Timothy; Nemecek, Stanislav; Neubauer, Michael; Neuffer, David; Newman, Myriam Q.; Nezhevenko, Oleg; Ng, Cho-Kuen; Nguyen, Anh Ky; Nguyen, Minh; Van Nguyen Thi,Hong; Niebuhr, Carsten; Niehoff, Jim; Niezurawski, Piotr; Nishitani, Tomohiro; Nitoh, Osamu; Noguchi, Shuichi; Nomerotski, Andrei; Noonan, John; Norbeck, Edward; Nosochkov, Yuri; Notz, Dieter; Nowak, Grazyna; Nowak, Hannelies; Noy, Matthew; Nozaki, Mitsuaki; Nyffeler, Andreas; Nygren, David; Oddone, Piermaria; O'Dell, Joseph; Oh, Jong-Seok; Oh, Sun Kun; Ohkuma, Kazumasa; Ohlerich, Martin; Ohmi, Kazuhito; Ohnishi, Yukiyoshi; Ohsawa, Satoshi; Ohuchi, Norihito; Oide, Katsunobu; Okada, Nobuchika; Okada, Yasuhiro; Okamura, Takahiro; Okugi, Toshiyuki; Okumi, Shoji; Okumura, Ken-ichi; Olchevski, Alexander; Oliver, William; Olivier, Bob; Olsen, James; Olsen, Jeff; Olsen, Stephen; Olshevsky, A.G.; Olsson, Jan; Omori, Tsunehiko; Onel, Yasar; Onengut, Gulsen; Ono, Hiroaki; Onoprienko, Dmitry; Oreglia, Mark; Oren, Will; Orimoto, Toyoko J.; Oriunno, Marco; Orlandea, Marius Ciprian; Oroku, Masahiro; Orr, Lynne H.; Orr, Robert S.; Oshea, Val; Oskarsson, Anders; Osland, Per; Ossetski, Dmitri; Österman, Lennart; Ostiguy, Francois; Otono, Hidetoshi; Ottewell, Brian; Ouyang, Qun; Padamsee, Hasan; Padilla, Cristobal; Pagani, Carlo; Palmer, Mark A.; Pam, Wei Min; Pande, Manjiri; Pande, Rajni; Pandit, V.S.; Pandita, P.N.; Pandurovic, Mila; Pankov, Alexander; Panzeri, Nicola; Papandreou, Zisis; Paparella, Rocco; Para, Adam; Park, Hwanbae; Parker, Brett; Parkes, Chris; Parma, Vittorio; Parsa, Zohreh; Parsons, Justin; Partridge, Richard; Pasquinelli, Ralph; Pásztor, Gabriella; Paterson, Ewan; Patrick, Jim; Patteri, Piero; Ritchie Patterson, J.; Pauletta, Giovanni; Paver, Nello; Pavlicek, Vince; Pawlik, Bogdan; Payet, Jacques; Pchalek, Norbert; Pedersen, John; Pei, Guo Xi; Pei, Shi Lun; Pelka, Jerzy; Pellegrini, Giulio; Pellett, David; Peng, G.X.; Penn, Gregory; Penzo, Aldo; Perry, Colin; Peskin, Michael; Peters, Franz; Petersen, Troels Christian; Peterson, Daniel; Peterson, Thomas; Petterson, Maureen; Pfeffer, Howard; Pfund, Phil; Phelps, Alan; Van Phi, Quang; Phillips, Jonathan; Piccolo, Marcello; Piemontese, Livio; Pierini, Paolo; Thomas Piggott, W.; Pike, Gary; Pillet, Nicolas; Jayawardena, Talini Pinto; Piot, Phillippe; Pitts, Kevin; Pivi, Mauro; Plate, Dave; Pleier, Marc-Andre; Poblaguev, Andrei; Poehler, Michael; Poelker, Matthew; Poffenberger, Paul; Pogorelsky, Igor; Poirier, Freddy; Poling, Ronald; Poole, Mike; Popescu, Sorina; Popielarski, John; Pöschl, Roman; Postranecky, Martin; Potukochi, Prakash N.; Prast, Julie; Prat, Serge; Preger, Miro; Prepost, Richard; Price, Michael; Proch, Dieter; Puntambekar, Avinash; Qin, Qing; Qu, Hua Min; Quadt, Arnulf; Quesnel, Jean-Pierre; Radeka, Veljko; Rahmat, Rahmat; Rai, Santosh Kumar; Raimondi, Pantaleo; Ramberg, Erik; Ranjan, Kirti; Rao, Sista V.L.S.; Raspereza, Alexei; Ratti, Alessandro; Ratti, Lodovico; Raubenheimer, Tor; Raux, Ludovic; Ravindran, V.; Raychaudhuri, Sreerup; Re, Valerio; Rease, Bill; Reece, Charles E.; Regler, Meinhard; Rehlich, Kay; Reichel, Ina; Reichold, Armin; Reid, John; Reid, Ron; Reidy, James; Reinhard, Marcel; Renz, Uwe; Repond, Jose; Resta-Lopez, Javier; Reuen, Lars; Ribnik, Jacob; Rice, Tyler; Richard, François; Riemann, Sabine; Riemann, Tord; Riles, Keith; Riley, Daniel; Rimbault, Cécile; Rindani, Saurabh; Rinolfi, Louis; Risigo, Fabio; Riu, Imma; Rizhikov, Dmitri; Rizzo, Thomas; Rochford, James H.; Rodriguez, Ponciano; Roeben, Martin; Rolandi, Gigi; Roodman, Aaron; Rosenberg, Eli; Roser, Robert; Ross, Marc; Rossel, François; Rossmanith, Robert; Roth, Stefan; Rougé, André; Rowe, Allan; Roy, Amit; Roy, Sendhunil B.; Roy, Sourov; Royer, Laurent; Royole-Degieux, Perrine; Royon, Christophe; Ruan, Manqi; Rubin, David; Ruehl, Ingo; Jimeno, Alberto Ruiz; Ruland, Robert; Rusnak, Brian; Ryu, Sun-Young; Sabbi, Gian Luca; Sadeh, Iftach; Sadygov, Ziraddin Y; Saeki, Takayuki; Sagan, David; Sahni, Vinod C.; Saini, Arun; Saito, Kenji; Saito, Kiwamu; Sajot, Gerard; Sakanaka, Shogo; Sakaue, Kazuyuki; Salata, Zen; Salih, Sabah; Salvatore, Fabrizio; Samson, Joergen; Sanami, Toshiya; Levi Sanchez, Allister; Sands, William; Santic, John; Sanuki, Tomoyuki; Sapronov, Andrey; Sarkar, Utpal; Sasao, Noboru; Satoh, Kotaro; Sauli, Fabio; Saunders, Claude; Saveliev, Valeri; Savoy-Navarro, Aurore; Sawyer, Lee; Saxton, Laura; Schäfer, Oliver; Schälicke, Andreas; Schade, Peter; Schaetzel, Sebastien; Scheitrum, Glenn; Schibler, Emilie; Schindler, Rafe; Schlösser, Markus; Schlueter, Ross D.; Schmid, Peter; Schmidt, Ringo Sebastian; Schneekloth, Uwe; Schreiber, Heinz Juergen; Schreiber, Siegfried; Schroeder, Henning; Peter Schüler, K.; Schulte, Daniel; Schultz-Coulon, Hans-Christian; Schumacher, Markus; Schumann, Steffen; Schumm, Bruce A.; Schwienhorst, Reinhard; Schwierz, Rainer; Scott, Duncan J.; Scuri, Fabrizio; Sefkow, Felix; Sefri, Rachid; Seguin-Moreau, Nathalie; Seidel, Sally; Seidman, David; Sekmen, Sezen; Seletskiy, Sergei; Senaha, Eibun; Senanayake, Rohan; Sendai, Hiroshi; Sertore, Daniele; Seryi, Andrei; Settles, Ronald; Sever, Ramazan; Shales, Nicholas; Shao, Ming; Shelkov, G.A.; Shepard, Ken; Shepherd-Themistocleous, Claire; Sheppard, John C.; Shi, Cai Tu; Shidara, Tetsuo; Shim, Yeo-Jeong; Shimizu, Hirotaka; Shimizu, Yasuhiro; Shimizu, Yuuki; Shimogawa, Tetsushi; Shin, Seunghwan; Shioden, Masaomi; Shipsey, Ian; Shirkov, Grigori; Shishido, Toshio; Shivpuri, Ram K.; Shrivastava, Purushottam; Shulga, Sergey; Shumeiko, Nikolai; Shuvalov, Sergey; Si, Zongguo; Siddiqui, Azher Majid; Siegrist, James; Simon, Claire; Simrock, Stefan; Sinev, Nikolai; Singh, Bhartendu K.; Singh, Jasbir; Singh, Pitamber; Singh, R.K.; Singh, S.K.; Singini, Monito; Sinha, Anil K.; Sinha, Nita; Sinha, Rahul; Sinram, Klaus; Sissakian, A.N.; Skachkov, N.B.; Skrinsky, Alexander; Slater, Mark; Slominski, Wojciech; Smiljanic, Ivan; Smith, A J Stewart; Smith, Alex; Smith, Brian J.; Smith, Jeff; Smith, Jonathan; Smith, Steve; Smith, Susan; Smith, Tonee; Neville Snodgrass, W.; Sobloher, Blanka; Sohn, Young-Uk; Solidum, Ruelson; Solyak, Nikolai; Son, Dongchul; Sonmez, Nasuf; Sopczak, Andre; Soskov, V.; Spencer, Cherrill M.; Spentzouris, Panagiotis; Speziali, Valeria; Spira, Michael; Sprehn, Daryl; Sridhar, K.; Srivastava, Asutosh; St. Lorant, Steve; Stahl, Achim; Stanek, Richard P.; Stanitzki, Marcel; Stanley, Jacob; Stefanov, Konstantin; Stein, Werner; Steiner, Herbert; Stenlund, Evert; Stern, Amir; Sternberg, Matt; Stockinger, Dominik; Stockton, Mark; Stoeck, Holger; Strachan, John; Strakhovenko, V.; Strauss, Michael; Striganov, Sergei I.; Strologas, John; Strom, David; Strube, Jan; Stupakov, Gennady; Su, Dong; Sudo, Yuji; Suehara, Taikan; Suehiro, Toru; Suetsugu, Yusuke; Sugahara, Ryuhei; Sugimoto, Yasuhiro; Sugiyama, Akira; Suh, Jun Suhk; Sukovic, Goran; Sun, Hong; Sun, Stephen; Sun, Werner; Sun, Yi; Sun, Yipeng; Suszycki, Leszek; Sutcliffe, Peter; Suthar, Rameshwar L.; Suwada, Tsuyoshi; Suzuki, Atsuto; Suzuki, Chihiro; Suzuki, Shiro; Suzuki, Takashi; Swent, Richard; Swientek, Krzysztof; Swinson, Christina; Syresin, Evgeny; Szleper, Michal; Tadday, Alexander; Takahashi, Rika; Takahashi, Tohru; Takano, Mikio; Takasaki, Fumihiko; Takeda, Seishi; Takenaka, Tateru; Takeshita, Tohru; Takubo, Yosuke; Tanaka, Masami; Tang, Chuan Xiang; Taniguchi, Takashi; Tantawi, Sami; Tapprogge, Stefan; Tartaglia, Michael A.; Tassielli, Giovanni Francesco; Tauchi, Toshiaki; Tavian, Laurent; Tawara, Hiroko; Taylor, Geoffrey; Telnov, Alexandre V.; Telnov, Valery; Tenenbaum, Peter; Teodorescu, Eliza; Terashima, Akio; Terracciano, Giuseppina; Terunuma, Nobuhiro; Teubner, Thomas; Teuscher, Richard; Theilacker, Jay; Thomson, Mark; Tice, Jeff; Tigner, Maury; Timmermans, Jan; Titov, Maxim; Tokareva, N.A.; Tollefson, Kirsten; Tomasek, Lukas; Tomovic, Savo; Tompkins, John; Tonutti, Manfred; Topkar, Anita; Toprek, Dragan; Toral, Fernando; Torrence, Eric; Traversi, Gianluca; Trimpl, Marcel; Mani Tripathi, S.; Trischuk, William; Trodden, Mark; Trubnikov, G.V.; Tschirhart, Robert; Tskhadadze, Edisher; Tsuchiya, Kiyosumi; Tsukamoto, Toshifumi; Tsunemi, Akira; Tucker, Robin; Turchetta, Renato; Tyndel, Mike; Uekusa, Nobuhiro; Ueno, Kenji; Umemori, Kensei; Ummenhofer, Martin; Underwood, David; Uozumi, Satoru; Urakawa, Junji; Urban, Jeremy; Uriot, Didier; Urner, David; Ushakov, Andrei; Usher, Tracy; Uzunyan, Sergey; Vachon, Brigitte; Valerio, Linda; Valin, Isabelle; Valishev, Alex; Vamra, Raghava; Van der Graaf, Harry; Van Kooten, Rick; Van Zandbergen, Gary; Vanel, Jean-Charles; Variola, Alessandro; Varner, Gary; Velasco, Mayda; Velte, Ulrich; Velthuis, Jaap; Vempati, Sundir K.; Venturini, Marco; Vescovi, Christophe; Videau, Henri; Vila, Ivan; Vincent, Pascal; Virey, Jean-Marc; Visentin, Bernard; Viti, Michele; Vo, Thanh Cuong; Vogel, Adrian; Vogt, Harald; von Toerne, Eckhard; Vorozhtsov, S.B.; Vos, Marcel; Votava, Margaret; Vrba, Vaclav; Wackeroth, Doreen; Wagner, Albrecht; Wagner, Carlos E.M.; Wagner, Stephen; Wake, Masayoshi; Walczak, Roman; Walkowiak, Wolfgang; Wallon, Samuel; Walsh, Roberval; Walston, Sean; Waltenberger, Wolfgang; Walz, Dieter; Wang, Chao En; Wang, Chun Hong; Wang, Dou; Wang, Faya; Wang, Guang Wei; Wang, Haitao; Wang, Jiang; Wang, Jiu Qing; Wang, Juwen; Wang, Lanfa; Wang, Lei; Wang, Min-Zu; Wang, Qing; Wang, Shu Hong; Wang, Xiaolian; Wang, Xue-Lei; Wang, Yi Fang; Wang, Zheng; Wanzenberg, Rainer; Ward, Bennie; Ward, David; Warmbein, Barbara; Warner, David W.; Warren, Matthew; Washio, Masakazu; Watanabe, Isamu; Watanabe, Ken; Watanabe, Takashi; Watanabe, Yuichi; Watson, Nigel; Wattimena, Nanda; Wayne, Mitchell; Weber, Marc; Weerts, Harry; Weiglein, Georg; Weiland, Thomas; Weinzierl, Stefan; Weise, Hans; Weisend, John; Wendt, Manfred; Wendt, Oliver; Wenzel, Hans; Wenzel, William A.; Wermes, Norbert; Werthenbach, Ulrich; Wesseln, Steve; Wester, William; White, Andy; White, Glen R.; Wichmann, Katarzyna; Wienemann, Peter; Wierba, Wojciech; Wilksen, Tim; Willis, William; Wilson, Graham W.; Wilson, John A.; Wilson, Robert; Wing, Matthew; Winter, Marc; Wirth, Brian D.; Wolbers, Stephen A.; Wolff, Dan; Wolski, Andrzej; Woodley, Mark D.; Woods, Michael; Woodward, Michael L.; Woolliscroft, Timothy; Worm, Steven; Wormser, Guy; Wright, Dennis; Wright, Douglas; Wu, Andy; Wu, Tao; Wu, Yue Liang; Xella, Stefania; Xia, Guoxing; Xia, Lei; Xiao, Aimin; Xiao, Liling; Xie, Jia Lin; Xing, Zhi-Zhong; Xiong, Lian You; Xu, Gang; Xu, Qing Jing; Yajnik, Urjit A.; Yakimenko, Vitaly; Yamada, Ryuji; Yamaguchi, Hiroshi; Yamamoto, Akira; Yamamoto, Hitoshi; Yamamoto, Masahiro; Yamamoto, Naoto; Yamamoto, Richard; Yamamoto, Yasuchika; Yamanaka, Takashi; Yamaoka, Hiroshi; Yamashita, Satoru; Yamazaki, Hideki; Yan, Wenbiao; Yang, Hai-Jun; Yang, Jin Min; Yang, Jongmann; Yang, Zhenwei; Yano, Yoshiharu; Yazgan, Efe; Yeh, G.P.; Yilmaz, Hakan; Yock, Philip; Yoda, Hakutaro; Yoh, John; Yokoya, Kaoru; Yokoyama, Hirokazu; York, Richard C.; Yoshida, Mitsuhiro; Yoshida, Takuo; Yoshioka, Tamaki; Young, Andrew; Yu, Cheng Hui; Yu, Jaehoon; Yu, Xian Ming; Yuan, Changzheng; Yue, Chong-Xing; Yue, Jun Hui; Zacek, Josef; Zagorodnov, Igor; Zalesak, Jaroslav; Zalikhanov, Boris; Zarnecki, Aleksander Filip; Zawiejski, Leszek; Zeitnitz, Christian; Zeller, Michael; Zerwas, Dirk; Zerwas, Peter; Zeyrek, Mehmet; Zhai, Ji Yuan; Zhang, Bao Cheng; Zhang, Bin; Zhang, Chuang; Zhang, He; Zhang, Jiawen; Zhang, Jing; Zhang, Jing Ru; Zhang, Jinlong; Zhang, Liang; Zhang, X.; Zhang, Yuan; Zhang, Zhige; Zhang, Zhiqing; Zhang, Ziping; Zhao, Haiwen; Zhao, Ji Jiu; Zhao, Jing Xia; Zhao, Ming Hua; Zhao, Sheng Chu; Zhao, Tianchi; Zhao, Tong Xian; Zhao, Zhen Tang; Zhao, Zhengguo; Zhou, De Min; Zhou, Feng; Zhou, Shun; Zhu, Shou Hua; Zhu, Xiong Wei; Zhukov, Valery; Zimmermann, Frank; Ziolkowski, Michael; Zisman, Michael S.; Zomer, Fabian; Zong, Zhang Guo; Zorba, Osman; Zutshi, Vishnu

    2007-01-01

    The International Linear Collider (ILC) is a 200-500 GeV center-of-mass high-luminosity linear electron-positron collider, based on 1.3 GHz superconducting radio-frequency (SCRF) accelerating cavities. The ILC has a total footprint of about 31 km and is designed for a peak luminosity of 2x10^34 cm^-2 s^-1. The complex includes a polarized electron source, an undulator-based positron source, two 6.7 km circumference damping rings, two-stage bunch compressors, two 11 km long main linacs and a 4.5 km long beam delivery system. This report is Volume III (Accelerator) of the four volume Reference Design Report, which describes the design and cost of the ILC.

  7. System Design Description PFP Thermal Stabilization

    Energy Technology Data Exchange (ETDEWEB)

    RISENMAY, H.R.

    2000-01-27

    DOE has authorized in their letter of August 2, 1999, the operation of these three furnaces, quote ''Operation of the three uncompleted muffle furnaces (No.3, No.4, and No.5) located in Room 235B is authorized, using the same feed charge limits as the two existing furnaces (No.1, and No.2) located in Room 230C,''. The above statement incorrectly refers to Room 230C whereas the correct location is Room 230A. The current effort is directed to initiate the operation and to complete the design activities DOE authorized the operation of the furnaces based on their Safety Evaluation Report (SER). Based on analogy and the principle of similarity, the risks and consequences of accidents both onsite and offsite due to operation of three furnaces are not significantly larger than those already evaluated with the two operating furnaces. Thermal stabilization operations and the material of feed for furnaces in Glovebox HA-21 I are essentially the same as those currently being stabilized in furnaces in Glovebox HC-21 C. Therefore the accident analysis has utilized identical accident scenarios in evaluation and no additional failure modes are introduced by HA-21 I muffle furnace operation that would enhance the consequences of accidents. Authorization Basis documents as referenced below (PFP FSAR and DOE Letter authorizing the operation) appear to contradict each other, i.e. one allows and authorizes the operation and the other imposes the restriction on the operation. The purpose of the PFP FSAR restrictions was to review thoroughly the design and installation of three furnaces and perform acceptance testing before approving the startup for operation. With the experience of operating the two furnaces in Glovebox HC-21C, and the knowledge of risks and hazards the facility operation, the plant is adequately prepared to operate these additional furnaces. ECN 653595 has been prepared to incorporate operation of the muffle furnaces in Glovebox HA-21 I into the

  8. The PIP-II Reference Design Report

    Energy Technology Data Exchange (ETDEWEB)

    Lebedev, Valeri, [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); et al.

    2015-06-01

    The Proton Improvement Plan-II (PIP-II) is a high-intensity proton facility being developed to support a world-leading neutrino program over the next two decades at Fermilab. PIP-II is an integral part of the U.S. Intensity Frontier Roadmap as described in the Particle Physics Project Prioritization Panel (P5) report of May 2014 [1]. As an immediate goal PIP-II is focused on upgrades to the Fermilab accelerator complex capable of providing a beam power in excess of 1 MW on target at the initiation of LBNF [1,2] operations. PIP-II is a part of a longer-term concept for a sustained campaign of upgrades and improvements to achieve multi-MW capabilities at Fermilab. PIP-II is based on three major thrusts. They are (1) the recently completed upgrades to the Recycler and Main Injector (MI) for the NOvA experiment, (2) the Proton Improvement Plan [3] currently underway, and (3) the Project X Reference Design [4]. Note that: The Proton Improvement Plan (PIP) consolidates a set of improvements to the existing Linac, Booster, and Main Injector (MI) aimed at supporting 15 Hz Booster beam operation. In combination, the NOvA upgrades and PIP create a capability of delivering 700 kW beam power from the Main Injector at 120 GeV; The scope of the Project X Reference Design Report was aimed well beyond PIP. It described a complete concept for a multi-MW proton facility that could support a broad particle physics program based on neutrino, kaon, muon, and nucleon experiments [5,6]. The Project X conceptual design has evolved over a number of years, incorporating continuous input on physics research goals and advances in the underlying technology development programs [7,8,9]. PIP-II, to high degree, inherits these goals as the goals for future developments and upgrades. This document (PIP-II Reference Design Report) describes an initial step in the development of the Fermilab accelerating complex. The plan described in this Report balances the far-term goals of the Laboratory

  9. Tokamak Physics EXperiment (TPX): Toroidal field magnet design, development and manufacture. SDRL 15, System design description. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-22

    This System Design Description, prepared in accordance with the TPX Project Management Plan provides a summary or TF Magnet System design features at the conclusion of Phase I, Preliminary Design and Manufacturing Research. The document includes the analytical and experimental bases for the design, and plans for implementation in final design, manufacturing, test, and magnet integration into the tokamak. Requirements for operation and maintenance are outlined, and references to sources of additional information are provided.

  10. International linear collider reference design report

    Energy Technology Data Exchange (ETDEWEB)

    Aarons, G.

    2007-06-22

    The International Linear Collider will give physicists a new cosmic doorway to explore energy regimes beyond the reach of today's accelerators. A proposed electron-positron collider, the ILC will complement the Large Hadron Collider, a proton-proton collider at the European Center for Nuclear Research (CERN) in Geneva, Switzerland, together unlocking some of the deepest mysteries in the universe. With LHC discoveries pointing the way, the ILC -- a true precision machine -- will provide the missing pieces of the puzzle. Consisting of two linear accelerators that face each other, the ILC will hurl some 10 billion electrons and their anti-particles, positrons, toward each other at nearly the speed of light. Superconducting accelerator cavities operating at temperatures near absolute zero give the particles more and more energy until they smash in a blazing crossfire at the centre of the machine. Stretching approximately 35 kilometres in length, the beams collide 14,000 times every second at extremely high energies -- 500 billion-electron-volts (GeV). Each spectacular collision creates an array of new particles that could answer some of the most fundamental questions of all time. The current baseline design allows for an upgrade to a 50-kilometre, 1 trillion-electron-volt (TeV) machine during the second stage of the project. This reference design provides the first detailed technical snapshot of the proposed future electron-positron collider, defining in detail the technical parameters and components that make up each section of the 31-kilometer long accelerator. The report will guide the development of the worldwide R&D program, motivate international industrial studies and serve as the basis for the final engineering design needed to make an official project proposal later this decade.

  11. KBS-3H design description 2005

    Energy Technology Data Exchange (ETDEWEB)

    Autio, Jorma (Saanio and Riekkola Oy, Helsinki (Finland))

    2008-05-15

    SKB and Posiva are performing an RandD program over the period of 2002-2007 with the overall aim to develop the KBS-3H to an alternative to the KBS-3V concept for disposal of spent nuclear fuel. A feasibility study of the KBS-3H concept was carried out in 2002, followed by the setting up of basic design in 2003. Several problems related to the behavior of the design and scope of future research and development work were addressed. Therefore the design basis was developed further and two candidate designs were developed: 1) previous Basic Design (BD) was developed more robust and tolerable to inflows. Parallel to that a novel modified 2) DAWE design with Drainage, Air evacuation and Watering and was developed to function robustly at various inflow situations. The candidate designs presented in this report include several novel components, such as fixing rings and steel plugs which have been designed without support of applicable design guidelines, regulations or standards available. The design basis and performance of these components include uncertainties, which should be studied and verified. It is possible that a feasible site specific design can be based on using both alternatives

  12. Search Hanford accessible reports electronically system design description. Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Gilomen, T.L.

    1995-12-31

    The Search Hanford Accessible Records Electronically (SHARE) system was produced by a combined team of personnel from Westinghouse Hanford Company (WHC) Corrective Action Data Systems (CADS) and Information Resource Management (IRM) Information and Scientific Systems (ISS) organizations. The ESQD Text Evaluation and exchange Tool (ETEXT) prototype was used as a basis for the requirements used to support this design/build effort. TOPIC was used to build the SHARE application. TOPIC is a text search and retrieval software product produced by the Verity Corporation. The TOPIC source code is not provided with the product, and the programs cannot be changed. TOPIC can be customized for special requirements. The software is fully documented. Help messages, menu and screen layouts, command edits and options, and internal system design are all described in the TOPIC documentation. This System Design Description (SDD) will not reiterate the TOPIC documentation and design. Instead, it will focus on the SHARE installation of TOPIC. This SDD is designed to assist the SHARE database/infobase administrator (DBA) in maintaining and supporting the application. It assumes that the assigned DBA is knowledgeable in using the TOPIC product, and is also knowledgeable in using a personal computer (PC), Disk Operating System (DOS) commands, and the document WHC-CM-3-10. SHARE is an Impact Level 4 system, and all activities related to SHARE must conform with the WHC-CM-3-10 procedures for an Impact Level 4 system. The Alternatives Analysis will be treated as a level 3-Q document, to allow for reference by potential future projects.

  13. Retrievable surface storage facility conceptual system design description

    Energy Technology Data Exchange (ETDEWEB)

    1977-03-01

    The studies evaluated several potentially attractive methods for processing and retrievably storing high-level radioactive waste after delivery to the Federal repository. These studies indicated that several systems could be engineered to safely store the waste, but that the simplest and most attractive concept from a technical standpoint would be to store the waste in a sealed stainless steel canister enclosed in a 2 in. thick carbon steel cask which in turn would be inserted into a reinforced concrete gamma-neutron shield, which would also provide the necessary air-cooling through an air annulus between the cask and the shield. This concept best satisfies the requirements for safety, long-term exposure to natural phenomena, low capital and operating costs, retrievability, amenability to incremental development, and acceptably small environmental impact. This document assumes that the reference site would be on ERDA's Hanford reservation. This document is a Conceptual System Design Description of the facilities which could satisfy all of the functional requirements within the established basic design criteria. The Retrievable Surface Storage Facility (RSSF) is planned with the capacity to process and store the waste received in either a calcine or glass/ceramic form. The RSSF planning is based on a modular development program in which the modular increments are constructed at rates matching projected waste receipts.

  14. Study design and description of patients.

    Science.gov (United States)

    Lutz, P; Schmidt, H; Batzler, U

    1990-01-01

    A West German multicentre study (eight centres) of PKU was designed in 1976. The subjects of the study are the differential diagnosis, factors influencing the therapeutic outcome, and the extension of dietary therapy into adolescence. Between 1978 and 1984, 165 patients were enrolled, of whom 38 were of non-German nationality. The educational and occupational status of the West German parents were comparable to the population of the Federal Republic of Germany. In the central data bank located at the University Childrens Hospital in Heidelberg, data from recurrent medical examinations and from biochemistry, dietetics, neurology, psychometry and demography were collected. The differential diagnosis of the elevated plasma Phe level in the newborn period resulted in the detection of 2 patients with a PTPS-deficiency, and of 163 with an apo-enzyme defect. Depending upon the magnitude of the Phe levels during the first weeks of life, preliminary treatment groups were formed. They were revised at the age of 6 months with a protein challenge. The levels of Phe during the protein challenge resulted in three types of response. Of these, type III can apparently forgo dietary restrictions resulting in plasma Phe concentrations of around 10 mg/dl. Preliminary results of the whole study are now presented.

  15. Description of sampling designs using a comprehensive data structure

    Science.gov (United States)

    John C. Byrne; Albert R. Stage

    1988-01-01

    Maintaining permanent plot data with different sampling designs over long periods within an organization, as well as sharing such information between organizations, requires that common standards be used. A data structure for the description of the sampling design within a stand is proposed. It is based on the definition of subpopulations of trees sampled, the rules...

  16. Spica-Safari reference optical design

    Science.gov (United States)

    Pastor, Carmen; Zuluaga, Pablo; Jellema, Willem; González Fernández, Luis Miguel; Belenguer, Tomas; Torres Redondo, Josefina; Kooijman, Peter Paul; Najarro, Francisco; Eggens, Martin; Roelfsema, Peter; Nakagawa, Takao

    2017-11-01

    SpicA FAR infrared Instrument, SAFARI, is an imaging spectrometer which is being designed to map large areas of the sky in the far infrared. The SPICA mission, having a large cold telescope cooled to 6K above absolute zero, will provide an optimum environment where instruments are limited only by the cosmic background itself.

  17. Tool Support for Design Patterns based on Reference Attribute Grammars

    DEFF Research Database (Denmark)

    Cornils, Aino; Hedin, Görel

    2000-01-01

    a flexible and extensible tool which enables designers to use design patterns in a safe and easy way and which semi-automatically documents and maintains the documentation of a software system. The system is implemented using reference attribute grammars (RAGs) which are capable of describing non......-local dependencies. Both the programming language and the design patterns are specified using RAGs, and reference attributes are used for connecting design pattern instances to the corresponding elements in the program code....

  18. Design/CPN. A Reference Manual

    DEFF Research Database (Denmark)

    Jensen et. al, Kurt

    /CPN WWW pages. To speed up the access to the Design/CPN manuals we recommend to keep a local copy - which may be shared by all users in your organisation. In this way you do not need to go via our WWW server each time you need to look in a manual. For some of the largest manuals, we also supply files...... containing smaller parts. In this way it is easy, e.g., to keep the index open in one window while you keep the main part open in another and perhaps the table of contents in a third. Corrections to the Design/CPN manuals are made by adding a number of "yellow stickers" to the PDF file - they open when you...

  19. Descriptions of reference LWR facilities for analysis of nuclear fuel cycles

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, K.J.; Kabele, T.J.

    1979-09-01

    To contribute to the Department of Energy's identification of needs for improved environmental controls in nuclear fuel cycles, a study was made of a light water reactor system. A reference LWR fuel cycle was defined, and each step in this cycle was characterized by facility description and mainline and effluent treatment process performance. The reference fuel cycle uses fresh uranium in light water reactors. Final treatment and ultimate disposition of waste from the fuel cycle steps were not included, and the waste is assumed to be disposed of by approved but currently undefined means. The characterization of the reference fuel cycle system is intended as basic information for further evaluation of alternative effluent control systems.

  20. A coherent description of the process of design

    DEFF Research Database (Denmark)

    Hertz, Kristian Dahl

    1992-01-01

    A description of the creative design process is given based on Empiricism and using the theory of sets on conceptual and subconscious representations of the human mind. Definitions that are more precise are given of a number of common concepts such as association, synthesis, culture, creation, art...

  1. [Descriptions of treatment in the Hippocratic Collection with special reference to surgery, particularly for urinary stones].

    Science.gov (United States)

    Saitoh, Hiroshi

    2006-03-01

    I analyzed mentions of treatment in the Hippocratic Collection. I examined quantitatively mentions of treatments in the Hippocratic Collection (Roeb edition, Otsuki edition, and Kon edition) to compare preferences for therapy between the Kos and Knidos schools. Treatments, mentioned in 2,687 passages, were medical in 2,319 (86%), and surgical in 368 (14%). These 2,687 descriptions included 1,023 (38%) from the Kos, 1,261 (47%) from the Knidos school, and 403 (15%) from unspecified schools. Of the 2,319 descriptions of medical treatment, 560 (24%) referred to medicines and 466 (20%) to diet, followed by baths, vapor baths, exercise, running, walking, warm applications, and others. The 368 surgical descriptions involved traction and adjustment for treating fractures of bones or dislocation of joints in 166 (45%) and surgery using knife or fire in 202 (55%). Of the latter 202 mentions, 87 (43%) referred to incision with knife, 74 (37%) to cauterization and 73 (37%) to bloodletting. Diet, exercises, running, walks, traction, adjustment and bloodletting were mentioned more frequently by the Kos school than the Knidos school, while medicines, baths, vapor baths (for gynecological diseases) and incision were mentioned more frequently by the Knidos school (chi-squared test, p Hippocratic Collection, while surgical treatments also were emphasized. Hippocrates warned beginning doctors not to used unproven treatments for urinary stone in the introduction to the "Oath", but did not forbid surgical treatments.

  2. Spent nuclear fuel project cold vacuum drying facility vacuum and purge system design description

    Energy Technology Data Exchange (ETDEWEB)

    IRWIN, J.J.

    1998-11-30

    This document provides the System Design Description (SDD) for the Cold Vacuum Drying Facility (CVDF) Vacuum and Purge System (VPS) . The SDD was developed in conjunction with HNF-SD-SNF-SAR-O02, Safety Analysis Report for the Cold Vacuum Drying Facility, Phase 2, Supporting Installation of Processing Systems (Garvin 1998), The HNF-SD-SNF-DRD-002, 1998, Cold Vacuum Drying Facility Design Requirements, and the CVDF Design Summary Report. The SDD contains general descriptions of the VPS equipment, the system functions, requirements and interfaces. The SDD provides references for design and fabrication details, operation sequences and maintenance. This SDD has been developed for the SNFP Operations Organization and shall be updated, expanded, and revised in accordance with future design, construction and startup phases of the CVDF until the CVDF final ORR is approved.

  3. Reference modular High Temperature Gas-Cooled Reactor Plant: Concept description report

    Energy Technology Data Exchange (ETDEWEB)

    1986-10-01

    This report provides a summary description of the Modular High Temperature Gas-Cooled Reactor (MHTGR) concept and interim results of assessments of costs, safety, constructibility, operability, maintainability, and availability. Conceptual design of this concept was initiated in October 1985 and is scheduled for completion in 1987. Participating industrial contractors are Bechtel National, Inc. (BNI), Stone and Webster Engineering Corporation (SWEC), GA Technologies, Inc. (GA), General Electric Co. (GE), and Combustion Engineering, Inc. (C-E).

  4. The neutronic analysis for the ITER reference breeding blanket design

    Energy Technology Data Exchange (ETDEWEB)

    Petrizzi, L.; Ferrari, M. [Association Euratom-ENEA sulla Fusione, Centro Ricerche Energia Frascati (Italy); Lopatkin, A.; Muratov, V. [RDIPE, Moscow (Russian Federation); Plenteda, R.; Santoro, R.; Valenza, D. [ITER Joint Work Site, Garching (Germany)

    1998-07-01

    This paper provides an overview of the neutronic analyses performed during the design development of the ITER breeding blanket beginning in 1997, when the reference BB design was started to the present. In Section 2 optimisation studies for the initial boundary conditions are presented. In Section 3, the detailed three dimensional analyses that were performed are illustrated plus additional optimisation for new boundary conditions. It is shown that a TBR = 0.97 is achieved in the reference configuration for the ITER machine as described in the Final Design Report of the ITER Engineering Design Activity. (authors)

  5. Selection of References in Wind Turbine Model Predictive Control Design

    DEFF Research Database (Denmark)

    Odgaard, Peter Fogh; Hovgaard, Tobias

    2015-01-01

    Lowering the cost of energy is one of the major focus areas in the wind turbine industry. Recent research has indicated that wind turbine controllers based on model predictive control methods can be useful in obtaining this objective. A number of design considerations have to be made when designing...... a model predictive controller for a wind turbine. One of the important aspects for a tracking control problem is how to setup the optimal reference tracking problem, as it might be relevant to track, e.g., the three concurrent references: optimal pitch angle, optimal rotational speed, and optimal power....... The importance if the individual references differ depending in particular on the wind speed. In this paper we investigate the performance of a reference tracking model predictive controller with two different setups of the used optimal reference signals. The controllers are evaluated using an industrial high...

  6. Reference task-based design of crisis management games

    NARCIS (Netherlands)

    Link, Daniel; Meesters, Kenny; Hellingrath, Bernd; van de Walle, B.A.; Hiltz, S.R.; Pfaff, M.S.; Plotnick, L.; Shih, P.C.

    Serious games are an effective tool for giving players a hands-on, immersive experience of crisis situations. To simplify the design of such games while ensuring their relevance, we propose a design method that is based on reference tasks. The feasibility of this approach is demonstrated by the

  7. A Stellar Reference Unit Design Study for SIRTF

    DEFF Research Database (Denmark)

    Jørgensen, John Leif; Liebe, Carl Christian

    1996-01-01

    A design study for a stellar reference unit, or star tracker, for SIRTF was conducted in FY96 in conjunction with the Tracking Sensors Group of the Avionic Equipment Section of JPL. The resulting design was derived from the Oersted, autonomous, Advanced Stellar Compass, star tracker. The projecte...

  8. Selecting the appropriate study design for your research: Descriptive study designs

    Directory of Open Access Journals (Sweden)

    Aamir Omair

    2015-01-01

    Full Text Available This article describes the importance of selecting the appropriate epidemiological study design for a given study question. It provides an explanation to the different terms used in describing study designs with regards to observational versus interventional and descriptive versus analytical types of study designs. This article focuses on the description of the different types of descriptive study designs, that is, case report, case series, correlational, and cross-sectional study designs. The requirements for selecting these study designs are discussed along with the advantages and disadvantages of each study design. The descriptive studies are similar in the context that they are based on a single sample with no comparative group within the study design. Their basic purpose is to describe the characteristics of the sample with regards to the characteristics that are present and so are useful in generating a hypothesis. The absence of a comparative group is the main limitation of the descriptive studies, and this is the reason they cannot be used to determine an association by testing a hypothesis showing a relationship between a risk factor and disease. The analytical study designs will be discussed in the next article in this series.

  9. Design description of the Tangaye Village photovoltaic power system

    Science.gov (United States)

    Martz, J. E.; Ratajczak, A. F.

    1982-01-01

    The engineering design of a stand alone photovoltaic (PV) powered grain mill and water pump for the village of Tangaye, Upper Volta is described. The socioeconomic effects of reducing the time required by women in rural areas for drawing water and grinding grain were studied. The suitability of photovoltaic technology for use in rural areas by people of limited technical training was demonstrated. The PV system consists of a 1.8-kW (peak) solar cell array, 540 ampere hours of battery storage, instrumentation, automatic controls, and a data collection and storage system. The PV system is situated near an improved village well and supplies d.c. power to a grain mill and a water pump. The array is located in a fenced area and the mill, battery, instruments, controls, and data system are in a mill building. A water storage tank is located near the well. The system employs automatic controls which provide battery charge regulation and system over and under voltage protection. This report includes descriptions of the engineering design of the system and of the load that it serves; a discussion of PV array and battery sizing methodology; descriptions of the mechanical and electrical designs including the array, battery, controls, and instrumentation; and a discussion of the safety features. The system became operational on March 1, 1979.

  10. Design description of the Tangaye Village photovoltaic power system

    Science.gov (United States)

    Martz, J. E.; Ratajczak, A. F.

    1982-06-01

    The engineering design of a stand alone photovoltaic (PV) powered grain mill and water pump for the village of Tangaye, Upper Volta is described. The socioeconomic effects of reducing the time required by women in rural areas for drawing water and grinding grain were studied. The suitability of photovoltaic technology for use in rural areas by people of limited technical training was demonstrated. The PV system consists of a 1.8-kW (peak) solar cell array, 540 ampere hours of battery storage, instrumentation, automatic controls, and a data collection and storage system. The PV system is situated near an improved village well and supplies d.c. power to a grain mill and a water pump. The array is located in a fenced area and the mill, battery, instruments, controls, and data system are in a mill building. A water storage tank is located near the well. The system employs automatic controls which provide battery charge regulation and system over and under voltage protection. This report includes descriptions of the engineering design of the system and of the load that it serves; a discussion of PV array and battery sizing methodology; descriptions of the mechanical and electrical designs including the array, battery, controls, and instrumentation; and a discussion of the safety features. The system became operational on March 1, 1979.

  11. ILC Reference Design Report Volume 1 - Executive Summary

    CERN Document Server

    Brau, James; Walker, Nicholas; Aarons, Gerald; Abe, Toshinori; Abernathy, Jason; Ablikim, Medina; Abramowicz, Halina; Adey, David; Adloff, Catherine; Adolphsen, Chris; Afanaciev, Konstantin; Agapov, Ilya; Ahn, Jung-Keun; Aihara, Hiroaki; Akemoto, Mitsuo; del Carmen Alabau, Maria; Albert, Justin; Albrecht, Hartwig; Albrecht, Michael; Alesini, David; Alexander, Gideon; Alexander, Jim; Allison, Wade; Amann, John; Amirikas, Ramila; An, Qi; Anami, Shozo; Ananthanarayan, B.; Anderson, Terry; Andricek, Ladislav; Anduze, Marc; Anerella, Michael; Anfimov, Nikolai; Angal-Kalinin, Deepa; Antipov, Sergei; Antoine, Claire; Aoki, Mayumi; Aoza, Atsushi; Aplin, Steve; Appleby, Rob; Arai, Yasuo; Araki, Sakae; Arkan, Tug; Arnold, Ned; Arnold, Ray; Arnowitt, Richard; Artru, Xavier; Arya, Kunal; Aryshev, Alexander; Asakawa, Eri; Asiri, Fred; Asner, David; Atac, Muzaffer; Atoian, Grigor; Attié, David; Augustin, Jean-Eudes; Augustine, David B.; Ayres, Bradley; Aziz, Tariq; Baars, Derek; Badaud, Frederique; Baddams, Nigel; Bagger, Jonathan; Bai, Sha; Bailey, David; Bailey, Ian R.; Baker, David; Balalykin, Nikolai I.; Balbuena, Juan Pablo; Baldy, Jean-Luc; Ball, Markus; Ball, Maurice; Ballestrero, Alessandro; Ballin, Jamie; Baltay, Charles; Bambade, Philip; Ban, Syuichi; Band, Henry; Bane, Karl; Banerjee, Bakul; Barbanotti, Serena; Barbareschi, Daniele; Barbaro-Galtieri, Angela; Barber, Desmond P.; Barbi, Mauricio; Bardin, Dmitri Y.; Barish, Barry; Barklow, Timothy L.; Barlow, Roger; Barnes, Virgil E.; Barone, Maura; Bartels, Christoph; Bartsch, Valeria; Basu, Rahul; Battaglia, Marco; Batygin, Yuri; Baudot, Jerome; Baur, Ulrich; Elwyn Baynham, D.; Beard, Carl; Bebek, Chris; Bechtle, Philip; Becker, Ulrich J.; Bedeschi, Franco; Bedjidian, Marc; Behera, Prafulla; Behnke, Ties; Bellantoni, Leo; Bellerive, Alain; Bellomo, Paul; Bentson, Lynn D.; Benyamna, Mustapha; Bergauer, Thomas; Berger, Edmond; Bergholz, Matthias; Beri, Suman; Berndt, Martin; Bernreuther, Werner; Bertolini, Alessandro; Besancon, Marc; Besson, Auguste; Beteille, Andre; Bettoni, Simona; Beyer, Michael; Bhandari, R.K.; Bharadwaj, Vinod; Bhatnagar, Vipin; Bhattacharya, Satyaki; Bhattacharyya, Gautam; Bhattacherjee, Biplob; Bhuyan, Ruchika; Bi, Xiao-Jun; Biagini, Marica; Bialowons, Wilhelm; Biebel, Otmar; Bieler, Thomas; Bierwagen, John; Birch, Alison; Bisset, Mike; Biswal, S.S.; Blackmore, Victoria; Blair, Grahame; Blanchard, Guillaume; Blazey, Gerald; Blue, Andrew; Blümlein, Johannes; Boffo, Christian; Bohn, Courtlandt; Boiko, V.I.; Boisvert, Veronique; Bondarchuk, Eduard N.; Boni, Roberto; Bonvicini, Giovanni; Boogert, Stewart; Boonekamp, Maarten; Boorman, Gary; Borras, Kerstin; Bortoletto, Daniela; Bosco, Alessio; Bosio, Carlo; Bosland, Pierre; Bosotti, Angelo; Boudry, Vincent; Boumediene, Djamel-Eddine; Bouquet, Bernard; Bourov, Serguei; Bowden, Gordon; Bower, Gary; Boyarski, Adam; Bozovic-Jelisavcic, Ivanka; Bozzi, Concezio; Brachmann, Axel; Bradshaw, Tom W.; Brandt, Andrew; Brasser, Hans Peter; Brau, Benjamin; Breidenbach, Martin; Bricker, Steve; Brient, Jean-Claude; Brock, Ian; Brodsky, Stanley; Brooksby, Craig; Broome, Timothy A.; Brown, David; Brown, David; Brownell, James H.; Bruchon, Mélanie; Brueck, Heiner; Brummitt, Amanda J.; Brun, Nicole; Buchholz, Peter; Budagov, Yulian A.; Bulgheroni, Antonio; Bulyak, Eugene; Bungau, Adriana; Bürger, Jochen; Burke, Dan; Burkhart, Craig; Burrows, Philip; Burt, Graeme; Burton, David; Büsser, Karsten; Butler, John; Butterworth, Jonathan; Buzulutskov, Alexei; Cabruja, Enric; Caccia, Massimo; Cai, Yunhai; Calcaterra, Alessandro; Caliier, Stephane; Camporesi, Tiziano; Cao, Jun-Jie; Cao, J.S.; Capatina, Ofelia; Cappellini, Chiara; Carcagno, Ruben; Carena, Marcela; Carloganu, Cristina; Carosi, Roberto; Stephen Carr, F.; Carrion, Francisco; Carter, Harry F.; Carter, John; Carwardine, John; Cassel, Richard; Cassell, Ronald; Cavallari, Giorgio; Cavallo, Emanuela; Cembranos, Jose A.R.; Chakraborty, Dhiman; Chandez, Frederic; Charles, Matthew; Chase, Brian; Chattopadhyay, Subhasis; Chauveau, Jacques; Chefdeville, Maximilien; Chehab, Robert; Chel, Stéphane; Chelkov, Georgy; Chen, Chiping; Chen, He Sheng; Chen, Huai Bi; Chen, Jia Er; Chen, Sen Yu; Chen, Shaomin; Chen, Shenjian; Chen, Xun; Chen, Yuan Bo; Cheng, Jian; Chevallier, M.; Chi, Yun Long; Chickering, William; Cho, Gi-Chol; Cho, Moo-Hyun; Choi, Jin-Hyuk; Choi, Jong Bum; Choi, Seong Youl; Choi, Young-Il; Choudhary, Brajesh; Choudhury, Debajyoti; Rai Choudhury, S.; Christian, David; Christian, Glenn; Christophe, Grojean; Chung, Jin-Hyuk; Church, Mike; Ciborowski, Jacek; Cihangir, Selcuk; Ciovati, Gianluigi; Clarke, Christine; Clarke, Don G.; Clarke, James A.; Clements, Elizabeth; Coca, Cornelia; Coe, Paul; Cogan, John; Colas, Paul; Collard, Caroline; Colledani, Claude; Combaret, Christophe; Comerma, Albert; Compton, Chris; Constance, Ben; Conway, John; Cook, Ed; Cooke, Peter; Cooper, William; Corcoran, Sean; Cornat, Rémi; Corner, Laura; Cortina Gil, Eduardo; Clay Corvin, W.; Cotta Ramusino, Angelo; Cowan, Ray; Crawford, Curtis; Cremaldi, Lucien M; Crittenden, James A.; Cussans, David; Cvach, Jaroslav; da Silva, Wilfrid; Dabiri Khah, Hamid; Dabrowski, Anne; Dabrowski, Wladyslaw; Dadoun, Olivier; Dai, Jian Ping; Dainton, John; Daly, Colin; Damerell, Chris; Danilov, Mikhail; Daniluk, Witold; Daram, Sarojini; Datta, Anindya; Dauncey, Paul; David, Jacques; Davier, Michel; Davies, Ken P.; Dawson, Sally; De Boer, Wim; De Curtis, Stefania; De Groot, Nicolo; de la Taille, Christophe; de Lira, Antonio; De Roeck, Albert; de Sangro, Riccardo; De Santis,Stefano; Deacon, Laurence; Deandrea, Aldo; Dehmelt, Klaus; Delagnes, Eric; Delahaye, Jean-Pierre; Delebecque, Pierre; Delerue, Nicholas; Delferriere, Olivier; Demarteau, Marcel; Deng, Zhi; Denisov, Yu.N.; Densham, Christopher J.; Desch, Klaus; Deshpande, Nilendra; Devanz, Guillaume; Devetak, Erik; Dexter, Amos; Di benedetto, Vito; Diéguez, Angel; Diener, Ralf; Dinh, Nguyen Dinh; Dixit, Madhu; Dixit, Sudhir; Djouadi, Abdelhak; Dolezal, Zdenek; Dollan, Ralph; Dong, Dong; Dong, Hai Yi; Dorfan, Jonathan; Dorokhov, Andrei; Doucas, George; Downing, Robert; Doyle, Eric; Doziere, Guy; Drago, Alessandro; Dragt, Alex; Drake, Gary; Drásal, Zbynek; Dreiner, Herbert; Drell, Persis; Driouichi, Chafik; Drozhdin, Alexandr; Drugakov, Vladimir; Du, Shuxian; Dugan, Gerald; Duginov, Viktor; Dulinski, Wojciech; Dulucq, Frederic; Dutta, Sukanta; Dwivedi, Jishnu; Dychkant, Alexandre; Dzahini, Daniel; Eckerlin, Guenter; Edwards, Helen; Ehrenfeld, Wolfgang; Ehrlichman, Michael; Ehrlichmann, Heiko; Eigen, Gerald; Elagin, Andrey; Elementi, Luciano; Eliasson, Peder; Ellis, John; Ellwood, George; Elsen, Eckhard; Emery, Louis; Enami, Kazuhiro; Endo, Kuninori; Enomoto, Atsushi; Eozénou, Fabien; Erbacher, Robin; Erickson, Roger; Oleg Eyser, K.; Fadeyev, Vitaliy; Fang, Shou Xian; Fant, Karen; Fasso, Alberto; Faucci Giannelli, Michele; Fehlberg, John; Feld, Lutz; Feng, Jonathan L.; Ferguson, John; Fernandez-Garcia, Marcos; Luis Fernandez-Hernando, J.; Fiala, Pavel; Fieguth, Ted; Finch, Alexander; Finocchiaro, Giuseppe; Fischer, Peter; Fisher, Peter; Eugene Fisk, H.; Fitton, Mike D.; Fleck, Ivor; Fleischer, Manfred; Fleury, Julien; Flood, Kevin; Foley, Mike; Ford, Richard; Fortin, Dominique; Foster, Brian; Fourches, Nicolas; Francis, Kurt; Frey, Ariane; Frey, Raymond; Friedsam, Horst; Frisch, Josef; Frishman, Anatoli; Fuerst, Joel; Fujii, Keisuke; Fujimoto, Junpei; Fukuda, Masafumi; Fukuda, Shigeki; Funahashi, Yoshisato; Funk, Warren; Furletova, Julia; Furukawa, Kazuro; Furuta, Fumio; Fusayasu, Takahiro; Fuster, Juan; Gadow, Karsten; Gaede, Frank; Gaglione, Renaud; Gai, Wei; Gajewski, Jan; Galik, Richard; Galkin, Alexei; Galkin, Valery; Gallin-Martel, Laurent; Gannaway, Fred; Gao, Jian She; Gao, Jie; Gao, Yuanning; Garbincius, Peter; Garcia-Tabares, Luis; Garren, Lynn; Garrido, Luís; Garutti, Erika; Garvey, Terry; Garwin, Edward; Gascón, David; Gastal, Martin; Gatto, Corrado; Gatto, Raoul; Gay, Pascal; Ge, Lixin; Ge, Ming Qi; Ge, Rui; Geiser, Achim; Gellrich, Andreas; Genat, Jean-Francois; Geng, Zhe Qiao; Gentile, Simonetta; Gerbick, Scot; Gerig, Rod; Ghosh, Dilip Kumar; Ghosh, Kirtiman; Gibbons, Lawrence; Giganon, Arnaud; Gillespie, Allan; Gillman, Tony; Ginzburg, Ilya; Giomataris, Ioannis; Giunta, Michele; Gladkikh, Peter; Gluza, Janusz; Godbole, Rohini; Godfrey, Stephen; Goldhaber, Gerson; Goldstein, Joel; Gollin, George D.; Gonzalez-Sanchez, Francisco Javier; Goodrick, Maurice; Gornushkin, Yuri; Gostkin, Mikhail; Gottschalk, Erik; Goudket, Philippe; Gough Eschrich, Ivo; Gournaris, Filimon; Graciani, Ricardo; Graf, Norman; Grah, Christian; Grancagnolo, Francesco; Grandjean, Damien; Grannis, Paul; Grassellino, Anna; Graugés, Eugeni; Gray, Stephen; Green, Michael; Greenhalgh, Justin; Greenshaw, Timothy; Grefe, Christian; Gregor, Ingrid-Maria; Grenier, Gerald; Grimes, Mark; Grimm, Terry; Gris, Philippe; Grivaz, Jean-Francois; Groll, Marius; Gronberg, Jeffrey; Grondin, Denis; Groom, Donald; Gross, Eilam; Grunewald, Martin; Grupen, Claus; Grzelak, Grzegorz; Gu, Jun; Gu, Yun-Ting; Guchait, Monoranjan; Guiducci, Susanna; Guler, Ali Murat; Guler, Hayg; Gulmez, Erhan; Gunion, John; Guo, Zhi Yu; Gurtu, Atul; Ha, Huy Bang; Haas, Tobias; Haase, Andy; Haba, Naoyuki; Haber, Howard; Haensel, Stephan; Hagge, Lars; Hagura, Hiroyuki; Hajdu, Csaba; Haller, Gunther; Haller, Johannes; Hallermann, Lea; Halyo, Valerie; Hamaguchi, Koichi; Hammond, Larry; Han, Liang; Han, Tao; Hand, Louis; Handu, Virender K.; Hano, Hitoshi; Hansen, Christian; Hansen, Jørn Dines; Hansen, Jorgen Beck; Hara, Kazufumi; Harder, Kristian; Hartin, Anthony; Hartung, Walter; Hast, Carsten; Hauptman, John; Hauschild, Michael; Hauviller, Claude; Havranek, Miroslav; Hawkes, Chris; Hawkings, Richard; Hayano, Hitoshi; Hazumi, Masashi; He, An; He, Hong Jian; Hearty, Christopher; Heath, Helen; Hebbeker, Thomas; Hedberg, Vincent; Hedin, David; Heifets, Samuel; Heinemeyer, Sven; Heini, Sebastien; Helebrant, Christian; Helms, Richard; Heltsley, Brian; Henrot-Versille, Sophie; Henschel, Hans; Hensel, Carsten; Hermel, Richard; Herms, Atilà; Herten, Gregor; Hesselbach, Stefan; Heuer, Rolf-Dieter; Heusch, Clemens A.; Hewett, Joanne; Higashi, Norio; Higashi, Takatoshi; Higashi, Yasuo; Higo, Toshiyasu; Hildreth, Michael D.; Hiller, Karlheinz; Hillert, Sonja; Hillier, Stephen James; Himel, Thomas; Himmi, Abdelkader; Hinchliffe, Ian; Hioki, Zenro; Hirano, Koichiro; Hirose, Tachishige; Hisamatsu, Hiromi; Hisano, Junji; Hlaing, Chit Thu; Hock, Kai Meng; Hoeferkamp, Martin; Hohlfeld, Mark; Honda, Yousuke; Hong, Juho; Hong, Tae Min; Honma, Hiroyuki; Horii, Yasuyuki; Horvath, Dezso; Hosoyama, Kenji; Hostachy, Jean-Yves; Hou, Mi; Hou, Wei-Shu; Howell, David; Hronek, Maxine; Hsiung, Yee B.; Hu, Bo; Hu, Tao; Huang, Jung-Yun; Huang, Tong Ming; Huang, Wen Hui; Huedem, Emil; Huggard, Peter; Hugonie, Cyril; Hu-Guo, Christine; Huitu, Katri; Hwang, Youngseok; Idzik, Marek; Ignatenko, Alexandr; Ignatov, Fedor; Ikeda, Hirokazu; Ikematsu, Katsumasa; Ilicheva, Tatiana; Imbault, Didier; Imhof, Andreas; Incagli, Marco; Ingbir, Ronen; Inoue, Hitoshi; Inoue, Youichi; Introzzi, Gianluca; Ioakeimidi, Katerina; Ishihara, Satoshi; Ishikawa, Akimasa; Ishikawa, Tadashi; Issakov, Vladimir; Ito, Kazutoshi; Ivanov, V.V.; Ivanov, Valentin; Ivanyushenkov, Yury; Iwasaki, Masako; Iwashita, Yoshihisa; Jackson, David; Jackson, Frank; Jacobsen, Bob; Jaganathan, Ramaswamy; Jamison, Steven; Janssen, Matthias Enno; Jaramillo-Echeverria, Richard; Jaros, John; Jauffret, Clement; Jawale, Suresh B.; Jeans, Daniel; Jedziniak, Ron; Jeffery, Ben; Jehanno, Didier; Jenner, Leo J.; Jensen, Chris; Jensen, David R.; Jiang, Hairong; Jiang, Xiao Ming; Jimbo, Masato; Jin, Shan; Keith Jobe, R.; Johnson, Anthony; Johnson, Erik; Johnson, Matt; Johnston, Michael; Joireman, Paul; Jokic, Stevan; Jones, James; Jones, Roger M.; Jongewaard, Erik; Jönsson, Leif; Joshi, Gopal; Joshi, Satish C.; Jung, Jin-Young; Junk, Thomas; Juste, Aurelio; Kado, Marumi; Kadyk, John; Käfer, Daniela; Kako, Eiji; Kalavase, Puneeth; Kalinin, Alexander; Kalinowski, Jan; Kamitani, Takuya; Kamiya, Yoshio; Kamiya, Yukihide; Kamoshita, Jun-ichi; Kananov, Sergey; Kanaya, Kazuyuki; Kanazawa, Ken-ichi; Kanemura, Shinya; Kang, Heung-Sik; Kang, Wen; Kanjial, D.; Kapusta, Frédéric; Karataev, Pavel; Karchin, Paul E.; Karlen, Dean; Karyotakis, Yannis; Kashikhin, Vladimir; Kashiwagi, Shigeru; Kasley, Paul; Katagiri, Hiroaki; Kato, Takashi; Kato, Yukihiro; Katzy, Judith; Kaukher, Alexander; Kaur, Manjit; Kawagoe, Kiyotomo; Kawamura, Hiroyuki; Kazakov, Sergei; Kekelidze, V.D.; Keller, Lewis; Kelley, Michael; Kelly, Marc; Kelly, Michael; Kennedy, Kurt; Kephart, Robert; Keung, Justin; Khainovski, Oleg; Khan, Sameen Ahmed; Khare, Prashant; Khovansky, Nikolai; Kiesling, Christian; Kikuchi, Mitsuo; Kilian, Wolfgang; Killenberg, Martin; Kim, Donghee; Kim, Eun San; Kim, Eun-Joo; Kim, Guinyun; Kim, Hongjoo; Kim, Hyoungsuk; Kim, Hyun-Chui; Kim, Jonghoon; Kim, Kwang-Je; Kim, Kyung Sook; Kim, Peter; Kim, Seunghwan; Kim, Shin-Hong; Kim, Sun Kee; Kim, Tae Jeong; Kim, Youngim; Kim, Young-Kee; Kimmitt, Maurice; Kirby, Robert; Kircher, François; Kisielewska, Danuta; Kittel, Olaf; Klanner, Robert; Klebaner, Arkadiy L.; Kleinwort, Claus; Klimkovich, Tatsiana; Klinkby, Esben; Kluth, Stefan; Knecht, Marc; Kneisel, Peter; Ko, In Soo; Ko, Kwok; Kobayashi, Makoto; Kobayashi, Nobuko; Kobel, Michael; Koch, Manuel; Kodys, Peter; Koetz, Uli; Kohrs, Robert; Kojima, Yuuji; Kolanoski, Hermann; Kolodziej, Karol; Kolomensky, Yury G.; Komamiya, Sachio; Kong, Xiang Cheng; Konigsberg, Jacobo; Korbel, Volker; Koscielniak, Shane; Kostromin, Sergey; Kowalewski, Robert; Kraml, Sabine; Krammer, Manfred; Krasnykh, Anatoly; Krautscheid, Thorsten; Krawczyk, Maria; James Krebs, H.; Krempetz, Kurt; Kribs, Graham; Krishnagopal, Srinivas; Kriske, Richard; Kronfeld, Andreas; Kroseberg, Jürgen; Kruchonak, Uladzimir; Kruecker, Dirk; Krüger, Hans; Krumpa, Nicholas A.; Krumshtein, Zinovii; Kuang, Yu Ping; Kubo, Kiyoshi; Kuchler, Vic; Kudoh, Noboru; Kulis, Szymon; Kumada, Masayuki; Kumar, Abhay; Kume, Tatsuya; Kundu, Anirban; Kurevlev, German; Kurihara, Yoshimasa; Kuriki, Masao; Kuroda, Shigeru; Kuroiwa, Hirotoshi; Kurokawa, Shin-ichi; Kusano, Tomonori; Kush, Pradeep K.; Kutschke, Robert; Kuznetsova, Ekaterina; Kvasnicka, Peter; Kwon, Youngjoon; Labarga, Luis; Lacasta, Carlos; Lackey, Sharon; Lackowski, Thomas W.; Lafaye, Remi; Lafferty, George; Lagorio, Eric; Laktineh, Imad; Lal, Shankar; Laloum, Maurice; Lam, Briant; Lancaster, Mark; Lander, Richard; Lange, Wolfgang; Langenfeld, Ulrich; Langeveld, Willem; Larbalestier, David; Larsen, Ray; Lastovicka, Tomas; Lastovicka-Medin, Gordana; Latina, Andrea; Latour, Emmanuel; Laurent, Lisa; Le, Ba Nam; Le, Duc Ninh; Le Diberder, Francois; Dû, Patrick Le; Lebbolo, Hervé; Lebrun, Paul; Lecoq, Jacques; Lee, Sung-Won; Lehner, Frank; Leibfritz, Jerry; Lenkszus, Frank; Lesiak, Tadeusz; Levy, Aharon; Lewandowski, Jim; Leyh, Greg; Li, Cheng; Li, Chong Sheng; Li, Chun Hua; Li, Da Zhang; Li, Gang; Li, Jin; Li, Shao Peng; Li, Wei Ming; Li, Weiguo; Li, Xiao Ping; Li, Xue-Qian; Li, Yuanjing; Li, Yulan; Li, Zenghai; Li, Zhong Quan; Liang, Jian Tao; Liao, Yi; Lilje, Lutz; Guilherme Lima, J.; Lintern, Andrew J.; Lipton, Ronald; List, Benno; List, Jenny; Liu, Chun; Liu, Jian Fei; Liu, Ke Xin; Liu, Li Qiang; Liu, Shao Zhen; Liu, Sheng Guang; Liu, Shubin; Liu, Wanming; Liu, Wei Bin; Liu, Ya Ping; Liu, Yu Dong; Lockyer, Nigel; Logan, Heather E.; Logatchev, Pavel V.; Lohmann, Wolfgang; Lohse, Thomas; Lola, Smaragda; Lopez-Virto, Amparo; Loveridge, Peter; Lozano, Manuel; Lu, Cai-Dian; Lu, Changguo; Lu, Gong-Lu; Lu, Wen Hui; Lubatti, Henry; Lucotte, Arnaud; Lundberg, Björn; Lundin, Tracy; Luo, Mingxing; Luong, Michel; Luth, Vera; Lutz, Benjamin; Lutz, Pierre; Lux, Thorsten; Luzniak, Pawel; Lyapin, Alexey; Lykken, Joseph; Lynch, Clare; Ma, Li; Ma, Lili; Ma, Qiang; Ma, Wen-Gan; Macfarlane, David; Maciel, Arthur; MacLeod, Allan; MacNair, David; Mader, Wolfgang; Magill, Stephen; Magnan, Anne-Marie; Maiheu, Bino; Maity, Manas; Majchrzak, Millicent; Majumder, Gobinda; Makarov, Roman; Makowski, Dariusz; Malaescu, Bogdan; Mallik, C.; Mallik, Usha; Malton, Stephen; Malyshev, Oleg B.; Malysheva, Larisa I.; Mammosser, John; Mamta; Mamuzic, Judita; Manen, Samuel; Manghisoni, Massimo; Manly, Steven; Marcellini, Fabio; Marcisovsky, Michal; Markiewicz, Thomas W.; Marks, Steve; Marone, Andrew; Marti, Felix; Martin, Jean-Pierre; Martin, Victoria; Martin-Chassard, Gisèle; Martinez, Manel; Martinez-Rivero, Celso; Martsch, Dennis; Martyn, Hans-Ulrich; Maruyama, Takashi; Masuzawa, Mika; Mathez, Hervé; Matsuda, Takeshi; Matsumoto, Hiroshi; Matsumoto, Shuji; Matsumoto, Toshihiro; Matsunaga, Hiroyuki; Mättig, Peter; Mattison, Thomas; Mavromanolakis, Georgios; Mawatari, Kentarou; Mazzacane, Anna; McBride, Patricia; McCormick, Douglas; McCormick, Jeremy; McDonald, Kirk T.; McGee, Mike; McIntosh, Peter; McKee, Bobby; McPherson, Robert A.; Meidlinger, Mandi; Meier, Karlheinz; Mele, Barbara; Meller, Bob; Melzer-Pellmann, Isabell-Alissandra; Mendez, Hector; Mercer, Adam; Merkin, Mikhail; Meshkov, I.N.; Messner, Robert; Metcalfe, Jessica; Meyer, Chris; Meyer, Hendrik; Meyer, Joachim; Meyer, Niels; Meyners, Norbert; Michelato, Paolo; Michizono, Shinichiro; Mihalcea, Daniel; Mihara, Satoshi; Mihara, Takanori; Mikami, Yoshinari; Mikhailichenko, Alexander A.; Milardi, Catia; Miller, David J.; Miller, Owen; Miller, Roger J.; Milstene, Caroline; Mimashi, Toshihiro; Minashvili, Irakli; Miquel, Ramon; Mishra, Shekhar; Mitaroff, Winfried; Mitchell, Chad; Miura, Takako; Miyamoto, Akiya; Miyata, Hitoshi; Mjörnmark, Ulf; Mnich, Joachim; Moenig, Klaus; Moffeit, Kenneth; Mokhov, Nikolai; Molloy, Stephen; Monaco, Laura; Monasterio, Paul R.; Montanari, Alessandro; Moon, Sung Ik; Moortgat-Pick, Gudrid A.; Mora de Freitas, Paulo; Morel, Federic; Moretti, Stefano; Morgunov, Vasily; Mori, Toshinori; Morin, Laurent; Morisseau, François; Morita, Yoshiyuki; Morita, Youhei; Morita, Yuichi; Morozov, Nikolai; Morozumi, Yuichi; Morse, William; Moser, Hans-Guenther; Moultaka, Gilbert; Mtingwa, Sekazi; Mudrinic, Mihajlo; Mueller, Alex; Mueller, Wolfgang; Muennich, Astrid; Muhlleitner, Milada Margarete; Mukherjee, Bhaskar; Mukhopadhyaya, Biswarup; Müller, Thomas; Munro, Morrison; Murayama, Hitoshi; Muto, Toshiya; Myneni, Ganapati Rao; Nabhiraj, P.Y.; Nagaitsev, Sergei; Nagamine, Tadashi; Nagano, Ai; Naito, Takashi; Nakai, Hirotaka; Nakajima, Hiromitsu; Nakamura, Isamu; Nakamura, Tomoya; Nakanishi, Tsutomu; Nakao, Katsumi; Nakao, Noriaki; Nakayoshi, Kazuo; Nam, Sang; Namito, Yoshihito; Namkung, Won; Nantista, Chris; Napoly, Olivier; Narain, Meenakshi; Naroska, Beate; Nauenberg, Uriel; Nayyar, Ruchika; Neal, Homer; Nelson, Charles; Nelson, Janice; Nelson, Timothy; Nemecek, Stanislav; Neubauer, Michael; Neuffer, David; Newman, Myriam Q.; Nezhevenko, Oleg; Ng, Cho-Kuen; Nguyen, Anh Ky; Nguyen, Minh; Van Nguyen Thi,Hong; Niebuhr, Carsten; Niehoff, Jim; Niezurawski, Piotr; Nishitani, Tomohiro; Nitoh, Osamu; Noguchi, Shuichi; Nomerotski, Andrei; Noonan, John; Norbeck, Edward; Nosochkov, Yuri; Notz, Dieter; Nowak, Grazyna; Nowak, Hannelies; Noy, Matthew; Nozaki, Mitsuaki; Nyffeler, Andreas; Nygren, David; Oddone, Piermaria; O'Dell, Joseph; Oh, Jong-Seok; Oh, Sun Kun; Ohkuma, Kazumasa; Ohlerich, Martin; Ohmi, Kazuhito; Ohnishi, Yukiyoshi; Ohsawa, Satoshi; Ohuchi, Norihito; Oide, Katsunobu; Okada, Nobuchika; Okamura, Takahiro; Okugi, Toshiyuki; Okumi, Shoji; Okumura, Ken-ichi; Olchevski, Alexander; Oliver, William; Olivier, Bob; Olsen, James; Olsen, Jeff; Olsen, Stephen; Olshevsky, A.G.; Olsson, Jan; Omori, Tsunehiko; Onel, Yasar; Onengut, Gulsen; Ono, Hiroaki; Onoprienko, Dmitry; Oreglia, Mark; Oren, Will; Orimoto, Toyoko J.; Oriunno, Marco; Orlandea, Marius Ciprian; Oroku, Masahiro; Orr, Lynne H.; Orr, Robert S.; Oshea, Val; Oskarsson, Anders; Osland, Per; Ossetski, Dmitri; Österman, Lennart; Ostiguy, Francois; Otono, Hidetoshi; Ottewell, Brian; Ouyang, Qun; Padamsee, Hasan; Padilla, Cristobal; Pagani, Carlo; Palmer, Mark A.; Pam, Wei Min; Pande, Manjiri; Pande, Rajni; Pandit, V.S.; Pandita, P.N.; Pandurovic, Mila; Pankov, Alexander; Panzeri, Nicola; Papandreou, Zisis; Paparella, Rocco; Para, Adam; Park, Hwanbae; Parker, Brett; Parkes, Chris; Parma, Vittorio; Parsa, Zohreh; Parsons, Justin; Partridge, Richard; Pasquinelli, Ralph; Pásztor, Gabriella; Paterson, Ewan; Patrick, Jim; Patteri, Piero; Ritchie Patterson, J.; Pauletta, Giovanni; Paver, Nello; Pavlicek, Vince; Pawlik, Bogdan; Payet, Jacques; Pchalek, Norbert; Pedersen, John; Pei, Guo Xi; Pei, Shi Lun; Pelka, Jerzy; Pellegrini, Giulio; Pellett, David; Peng, G.X.; Penn, Gregory; Penzo, Aldo; Perry, Colin; Peskin, Michael; Peters, Franz; Petersen, Troels Christian; Peterson, Daniel; Peterson, Thomas; Petterson, Maureen; Pfeffer, Howard; Pfund, Phil; Phelps, Alan; Van Phi, Quang; Phillips, Jonathan; Phinney, Nan; Piccolo, Marcello; Piemontese, Livio; Pierini, Paolo; Thomas Piggott, W.; Pike, Gary; Pillet, Nicolas; Jayawardena, Talini Pinto; Piot, Phillippe; Pitts, Kevin; Pivi, Mauro; Plate, Dave; Pleier, Marc-Andre; Poblaguev, Andrei; Poehler, Michael; Poelker, Matthew; Poffenberger, Paul; Pogorelsky, Igor; Poirier, Freddy; Poling, Ronald; Poole, Mike; Popescu, Sorina; Popielarski, John; Pöschl, Roman; Postranecky, Martin; Potukochi, Prakash N.; Prast, Julie; Prat, Serge; Preger, Miro; Prepost, Richard; Price, Michael; Proch, Dieter; Puntambekar, Avinash; Qin, Qing; Qu, Hua Min; Quadt, Arnulf; Quesnel, Jean-Pierre; Radeka, Veljko; Rahmat, Rahmat; Rai, Santosh Kumar; Raimondi, Pantaleo; Ramberg, Erik; Ranjan, Kirti; Rao, Sista V.L.S.; Raspereza, Alexei; Ratti, Alessandro; Ratti, Lodovico; Raubenheimer, Tor; Raux, Ludovic; Ravindran, V.; Raychaudhuri, Sreerup; Re, Valerio; Rease, Bill; Reece, Charles E.; Regler, Meinhard; Rehlich, Kay; Reichel, Ina; Reichold, Armin; Reid, John; Reid, Ron; Reidy, James; Reinhard, Marcel; Renz, Uwe; Repond, Jose; Resta-Lopez, Javier; Reuen, Lars; Ribnik, Jacob; Rice, Tyler; Richard, François; Riemann, Sabine; Riemann, Tord; Riles, Keith; Riley, Daniel; Rimbault, Cécile; Rindani, Saurabh; Rinolfi, Louis; Risigo, Fabio; Riu, Imma; Rizhikov, Dmitri; Rizzo, Thomas; Rochford, James H.; Rodriguez, Ponciano; Roeben, Martin; Rolandi, Gigi; Roodman, Aaron; Rosenberg, Eli; Roser, Robert; Ross, Marc; Rossel, François; Rossmanith, Robert; Roth, Stefan; Rougé, André; Rowe, Allan; Roy, Amit; Roy, Sendhunil B.; Roy, Sourov; Royer, Laurent; Royole-Degieux, Perrine; Royon, Christophe; Ruan, Manqi; Rubin, David; Ruehl, Ingo; Jimeno, Alberto Ruiz; Ruland, Robert; Rusnak, Brian; Ryu, Sun-Young; Sabbi, Gian Luca; Sadeh, Iftach; Sadygov, Ziraddin Y; Saeki, Takayuki; Sagan, David; Sahni, Vinod C.; Saini, Arun; Saito, Kenji; Saito, Kiwamu; Sajot, Gerard; Sakanaka, Shogo; Sakaue, Kazuyuki; Salata, Zen; Salih, Sabah; Salvatore, Fabrizio; Samson, Joergen; Sanami, Toshiya; Levi Sanchez, Allister; Sands, William; Santic, John; Sanuki, Tomoyuki; Sapronov, Andrey; Sarkar, Utpal; Sasao, Noboru; Satoh, Kotaro; Sauli, Fabio; Saunders, Claude; Saveliev, Valeri; Savoy-Navarro, Aurore; Sawyer, Lee; Saxton, Laura; Schäfer, Oliver; Schälicke, Andreas; Schade, Peter; Schaetzel, Sebastien; Scheitrum, Glenn; Schibler, Emilie; Schindler, Rafe; Schlösser, Markus; Schlueter, Ross D.; Schmid, Peter; Schmidt, Ringo Sebastian; Schneekloth, Uwe; Schreiber, Heinz Juergen; Schreiber, Siegfried; Schroeder, Henning; Peter Schüler, K.; Schulte, Daniel; Schultz-Coulon, Hans-Christian; Schumacher, Markus; Schumann, Steffen; Schumm, Bruce A.; Schwienhorst, Reinhard; Schwierz, Rainer; Scott, Duncan J.; Scuri, Fabrizio; Sefkow, Felix; Sefri, Rachid; Seguin-Moreau, Nathalie; Seidel, Sally; Seidman, David; Sekmen, Sezen; Seletskiy, Sergei; Senaha, Eibun; Senanayake, Rohan; Sendai, Hiroshi; Sertore, Daniele; Seryi, Andrei; Settles, Ronald; Sever, Ramazan; Shales, Nicholas; Shao, Ming; Shelkov, G.A.; Shepard, Ken; Shepherd-Themistocleous, Claire; Sheppard, John C.; Shi, Cai Tu; Shidara, Tetsuo; Shim, Yeo-Jeong; Shimizu, Hirotaka; Shimizu, Yasuhiro; Shimizu, Yuuki; Shimogawa, Tetsushi; Shin, Seunghwan; Shioden, Masaomi; Shipsey, Ian; Shirkov, Grigori; Shishido, Toshio; Shivpuri, Ram K.; Shrivastava, Purushottam; Shulga, Sergey; Shumeiko, Nikolai; Shuvalov, Sergey; Si, Zongguo; Siddiqui, Azher Majid; Siegrist, James; Simon, Claire; Simrock, Stefan; Sinev, Nikolai; Singh, Bhartendu K.; Singh, Jasbir; Singh, Pitamber; Singh, R.K.; Singh, S.K.; Singini, Monito; Sinha, Anil K.; Sinha, Nita; Sinha, Rahul; Sinram, Klaus; Sissakian, A.N.; Skachkov, N.B.; Skrinsky, Alexander; Slater, Mark; Slominski, Wojciech; Smiljanic, Ivan; Smith, A J Stewart; Smith, Alex; Smith, Brian J.; Smith, Jeff; Smith, Jonathan; Smith, Steve; Smith, Susan; Smith, Tonee; Neville Snodgrass, W.; Sobloher, Blanka; Sohn, Young-Uk; Solidum, Ruelson; Solyak, Nikolai; Son, Dongchul; Sonmez, Nasuf; Sopczak, Andre; Soskov, V.; Spencer, Cherrill M.; Spentzouris, Panagiotis; Speziali, Valeria; Spira, Michael; Sprehn, Daryl; Sridhar, K.; Srivastava, Asutosh; St. Lorant, Steve; Stahl, Achim; Stanek, Richard P.; Stanitzki, Marcel; Stanley, Jacob; Stefanov, Konstantin; Stein, Werner; Steiner, Herbert; Stenlund, Evert; Stern, Amir; Sternberg, Matt; Stockinger, Dominik; Stockton, Mark; Stoeck, Holger; Strachan, John; Strakhovenko, V.; Strauss, Michael; Striganov, Sergei I.; Strologas, John; Strom, David; Strube, Jan; Stupakov, Gennady; Su, Dong; Sudo, Yuji; Suehara, Taikan; Suehiro, Toru; Suetsugu, Yusuke; Sugahara, Ryuhei; Sugimoto, Yasuhiro; Sugiyama, Akira; Suh, Jun Suhk; Sukovic, Goran; Sun, Hong; Sun, Stephen; Sun, Werner; Sun, Yi; Sun, Yipeng; Suszycki, Leszek; Sutcliffe, Peter; Suthar, Rameshwar L.; Suwada, Tsuyoshi; Suzuki, Atsuto; Suzuki, Chihiro; Suzuki, Shiro; Suzuki, Takashi; Swent, Richard; Swientek, Krzysztof; Swinson, Christina; Syresin, Evgeny; Szleper, Michal; Tadday, Alexander; Takahashi, Rika; Takahashi, Tohru; Takano, Mikio; Takasaki, Fumihiko; Takeda, Seishi; Takenaka, Tateru; Takeshita, Tohru; Takubo, Yosuke; Tanaka, Masami; Tang, Chuan Xiang; Taniguchi, Takashi; Tantawi, Sami; Tapprogge, Stefan; Tartaglia, Michael A.; Tassielli, Giovanni Francesco; Tauchi, Toshiaki; Tavian, Laurent; Tawara, Hiroko; Taylor, Geoffrey; Telnov, Alexandre V.; Telnov, Valery; Tenenbaum, Peter; Teodorescu, Eliza; Terashima, Akio; Terracciano, Giuseppina; Terunuma, Nobuhiro; Teubner, Thomas; Teuscher, Richard; Theilacker, Jay; Thomson, Mark; Tice, Jeff; Tigner, Maury; Timmermans, Jan; Titov, Maxim; Toge, Nobukazu; Tokareva, N.A.; Tollefson, Kirsten; Tomasek, Lukas; Tomovic, Savo; Tompkins, John; Tonutti, Manfred; Topkar, Anita; Toprek, Dragan; Toral, Fernando; Torrence, Eric; Traversi, Gianluca; Trimpl, Marcel; Mani Tripathi, S.; Trischuk, William; Trodden, Mark; Trubnikov, G.V.; Tschirhart, Robert; Tskhadadze, Edisher; Tsuchiya, Kiyosumi; Tsukamoto, Toshifumi; Tsunemi, Akira; Tucker, Robin; Turchetta, Renato; Tyndel, Mike; Uekusa, Nobuhiro; Ueno, Kenji; Umemori, Kensei; Ummenhofer, Martin; Underwood, David; Uozumi, Satoru; Urakawa, Junji; Urban, Jeremy; Uriot, Didier; Urner, David; Ushakov, Andrei; Usher, Tracy; Uzunyan, Sergey; Vachon, Brigitte; Valerio, Linda; Valin, Isabelle; Valishev, Alex; Vamra, Raghava; Van der Graaf, Harry; Van Kooten, Rick; Van Zandbergen, Gary; Vanel, Jean-Charles; Variola, Alessandro; Varner, Gary; Velasco, Mayda; Velte, Ulrich; Velthuis, Jaap; Vempati, Sundir K.; Venturini, Marco; Vescovi, Christophe; Videau, Henri; Vila, Ivan; Vincent, Pascal; Virey, Jean-Marc; Visentin, Bernard; Viti, Michele; Vo, Thanh Cuong; Vogel, Adrian; Vogt, Harald; von Toerne, Eckhard; Vorozhtsov, S.B.; Vos, Marcel; Votava, Margaret; Vrba, Vaclav; Wackeroth, Doreen; Wagner, Albrecht; Wagner, Carlos E.M.; Wagner, Stephen; Wake, Masayoshi; Walczak, Roman; Walkowiak, Wolfgang; Wallon, Samuel; Walsh, Roberval; Walston, Sean; Waltenberger, Wolfgang; Walz, Dieter; Wang, Chao En; Wang, Chun Hong; Wang, Dou; Wang, Faya; Wang, Guang Wei; Wang, Haitao; Wang, Jiang; Wang, Jiu Qing; Wang, Juwen; Wang, Lanfa; Wang, Lei; Wang, Min-Zu; Wang, Qing; Wang, Shu Hong; Wang, Xiaolian; Wang, Xue-Lei; Wang, Yi Fang; Wang, Zheng; Wanzenberg, Rainer; Ward, Bennie; Ward, David; Warmbein, Barbara; Warner, David W.; Warren, Matthew; Washio, Masakazu; Watanabe, Isamu; Watanabe, Ken; Watanabe, Takashi; Watanabe, Yuichi; Watson, Nigel; Wattimena, Nanda; Wayne, Mitchell; Weber, Marc; Weerts, Harry; Weiglein, Georg; Weiland, Thomas; Weinzierl, Stefan; Weise, Hans; Weisend, John; Wendt, Manfred; Wendt, Oliver; Wenzel, Hans; Wenzel, William A.; Wermes, Norbert; Werthenbach, Ulrich; Wesseln, Steve; Wester, William; White, Andy; White, Glen R.; Wichmann, Katarzyna; Wienemann, Peter; Wierba, Wojciech; Wilksen, Tim; Willis, William; Wilson, Graham W.; Wilson, John A.; Wilson, Robert; Wing, Matthew; Winter, Marc; Wirth, Brian D.; Wolbers, Stephen A.; Wolff, Dan; Wolski, Andrzej; Woodley, Mark D.; Woods, Michael; Woodward, Michael L.; Woolliscroft, Timothy; Worm, Steven; Wormser, Guy; Wright, Dennis; Wright, Douglas; Wu, Andy; Wu, Tao; Wu, Yue Liang; Xella, Stefania; Xia, Guoxing; Xia, Lei; Xiao, Aimin; Xiao, Liling; Xie, Jia Lin; Xing, Zhi-Zhong; Xiong, Lian You; Xu, Gang; Xu, Qing Jing; Yajnik, Urjit A.; Yakimenko, Vitaly; Yamada, Ryuji; Yamaguchi, Hiroshi; Yamamoto, Akira; Yamamoto, Hitoshi; Yamamoto, Masahiro; Yamamoto, Naoto; Yamamoto, Richard; Yamamoto, Yasuchika; Yamanaka, Takashi; Yamaoka, Hiroshi; Yamashita, Satoru; Yamazaki, Hideki; Yan, Wenbiao; Yang, Hai-Jun; Yang, Jin Min; Yang, Jongmann; Yang, Zhenwei; Yano, Yoshiharu; Yazgan, Efe; Yeh, G.P.; Yilmaz, Hakan; Yock, Philip; Yoda, Hakutaro; Yoh, John; Yokoya, Kaoru; Yokoyama, Hirokazu; York, Richard C.; Yoshida, Mitsuhiro; Yoshida, Takuo; Yoshioka, Tamaki; Young, Andrew; Yu, Cheng Hui; Yu, Jaehoon; Yu, Xian Ming; Yuan, Changzheng; Yue, Chong-Xing; Yue, Jun Hui; Zacek, Josef; Zagorodnov, Igor; Zalesak, Jaroslav; Zalikhanov, Boris; Zarnecki, Aleksander Filip; Zawiejski, Leszek; Zeitnitz, Christian; Zeller, Michael; Zerwas, Dirk; Zerwas, Peter; Zeyrek, Mehmet; Zhai, Ji Yuan; Zhang, Bao Cheng; Zhang, Bin; Zhang, Chuang; Zhang, He; Zhang, Jiawen; Zhang, Jing; Zhang, Jing Ru; Zhang, Jinlong; Zhang, Liang; Zhang, X.; Zhang, Yuan; Zhang, Zhige; Zhang, Zhiqing; Zhang, Ziping; Zhao, Haiwen; Zhao, Ji Jiu; Zhao, Jing Xia; Zhao, Ming Hua; Zhao, Sheng Chu; Zhao, Tianchi; Zhao, Tong Xian; Zhao, Zhen Tang; Zhao, Zhengguo; Zhou, De Min; Zhou, Feng; Zhou, Shun; Zhu, Shou Hua; Zhu, Xiong Wei; Zhukov, Valery; Zimmermann, Frank; Ziolkowski, Michael; Zisman, Michael S.; Zomer, Fabian; Zong, Zhang Guo; Zorba, Osman; Zutshi, Vishnu

    2007-01-01

    The International Linear Collider (ILC) is a 200-500 GeV center-of-mass high-luminosity linear electron-positron collider, based on 1.3 GHz superconducting radio-frequency (SCRF) accelerating cavities. The ILC has a total footprint of about 31 km and is designed for a peak luminosity of 2x10^34 cm^-2s^-1. This report is the Executive Summary (Volume I) of the four volume Reference Design Report. It gives an overview of the physics at the ILC, the accelerator design and value estimate, the detector concepts, and the next steps towards project realization.

  12. Human Exploration of Mars Design Reference Architecture 5.0

    Science.gov (United States)

    Drake, Bret G.

    2010-01-01

    This paper provides a summary of the Mars Design Reference Architecture 5.0 (DRA 5.0), which is the latest in a series of NASA Mars reference missions. It provides a vision of one potential approach to human Mars exploration. The reference architecture provides a common framework for future planning of systems concepts, technology development, and operational testing as well as Mars robotic missions, research that is conducted on the International Space Station, and future lunar exploration missions. This summary the Mars DRA 5.0 provides an overview of the overall mission approach, surface strategy and exploration goals, as well as the key systems and challenges for the first three human missions to Mars.

  13. Computer system design description for SY-101 hydrogen mitigation test project data acquisition and control system (DACS-1)

    Energy Technology Data Exchange (ETDEWEB)

    Ermi, A.M.

    1997-05-01

    Description of the Proposed Activity/REPORTABLE OCCURRENCE or PIAB: This ECN changes the computer systems design description support document describing the computers system used to control, monitor and archive the processes and outputs associated with the Hydrogen Mitigation Test Pump installed in SY-101. There is no new activity or procedure associated with the updating of this reference document. The updating of this computer system design description maintains an agreed upon documentation program initiated within the test program and carried into operations at time of turnover to maintain configuration control as outlined by design authority practicing guidelines. There are no new credible failure modes associated with the updating of information in a support description document. The failure analysis of each change was reviewed at the time of implementation of the Systems Change Request for all the processes changed. This document simply provides a history of implementation and current system status.

  14. High Flux Isotope Reactor cold neutron source reference design concept

    Energy Technology Data Exchange (ETDEWEB)

    Selby, D.L.; Lucas, A.T.; Hyman, C.R. [and others

    1998-05-01

    In February 1995, Oak Ridge National Laboratory`s (ORNL`s) deputy director formed a group to examine the need for upgrades to the High Flux Isotope Reactor (HFIR) system in light of the cancellation of the Advanced neutron Source Project. One of the major findings of this study was that there was an immediate need for the installation of a cold neutron source facility in the HFIR complex. In May 1995, a team was formed to examine the feasibility of retrofitting a liquid hydrogen (LH{sub 2}) cold source facility into an existing HFIR beam tube. The results of this feasibility study indicated that the most practical location for such a cold source was the HB-4 beam tube. This location provides a potential flux environment higher than the Institut Laue-Langevin (ILL) vertical cold source and maximizes the space available for a future cold neutron guide hall expansion. It was determined that this cold neutron beam would be comparable, in cold neutron brightness, to the best facilities in the world, and a decision was made to complete a preconceptual design study with the intention of proceeding with an activity to install a working LH{sub 2} cold source in the HFIR HB-4 beam tube. During the development of the reference design the liquid hydrogen concept was changed to a supercritical hydrogen system for a number of reasons. This report documents the reference supercritical hydrogen design and its performance. The cold source project has been divided into four phases: (1) preconceptual, (2) conceptual design and testing, (3) detailed design and procurement, and (4) installation and operation. This report marks the conclusion of the conceptual design phase and establishes the baseline reference concept.

  15. Next-Generation Space Telescope design reference mission

    Science.gov (United States)

    Smith, Eric P.; Mather, John C.; Stockman, Hervey S.; Bely, Pierre Y.; Stiavelli, Massimo; Burg, Richard

    1998-08-01

    The Next Generation Space Telescope (NGST) Design Reference Mission (DRM) represents a suite of potential astronomical programs and targets along with their expected physical properties, and desired observation modes. This broad science program is being used to drive the observatory design in a way as fundamental as traditional engineering parameters. Astronomers use the DRM to communicate their desires in a quantitative fashion to the engineers who will eventually construct the observatory. The DRM is also the primary tool used to measure the relative value of NGST mission architectures and technological readiness of the program. Specifically, the fraction of the DRM completed by a given observatory configuration in a given time is, to first order, a measure of the value of the design. Those designs which complete a higher fraction of the observations listed below are more capable than those complete lesser fractions.

  16. TPX: Contractor preliminary design review. Volume 1, Presentation and design description. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hartman, D.; Naumovich, [Everson Electric Co., Bekthlehem, PA (United States); Walstrom, P.; Clarkson, I.; Schultheiss, J.; Burger, A. [Northrop Grumman Corp., Bethpage, NY (United States)

    1995-09-22

    This first volume of the five volume set begins with a CPDR overview and then details the PF magnet system, manufacturing R&D, Westinghouse R&D, the central solenoid, the PF 5 ring coil, the PF 6/7 ring coil, quality assurance, and the system design description.

  17. REFERENCE POINTS IN CURRICULUM DESIGN: GEOGRAPHY AS A SCHOOL SUBJECT

    Directory of Open Access Journals (Sweden)

    Octavian MÂNDRUŢ

    2017-12-01

    Full Text Available This study is theoretical and exploratory. It aims to describe a reference system which should determine or influence the decisions for the new curriculum design. The example of geography as a subject matter (or, in a wider perspective, of a field of study called “Geography – Environmental Studies” reveals specific elements resulting from the characteristics of the interior structure. The reference system may be altered, reduced, amplified, categorized or adjusted with respect to other subjects or fields of study, that are at least similar. The example of the “vertical” curriculum of Geography (grades V – XII relies upon a system of outcomes (competencies in progression (according to levels and ages and it depends on the time horizon of the design. Consequently, different options might come out within the process. Nevertheless, the curriculum depends a lot on the paradigm of its design: with a scientific dominance (with a likely minimal individual human insertion or with a subjective touch, as a result of some individual or group opinions which are more or less justified.

  18. The design of the new NPL reference spectrofluorimeter

    Science.gov (United States)

    Shaw, Michael J.; Clarke, Peter J.; Burnitt, Timothy A.

    2003-11-01

    To meet demands for increased traceability of fluorescence measurement a new two-monochromator reference spectrofluorimeter has been designed and built at NPL. This new instrument is capable of measuring the radiance factor and associated colorimetry of solid and liquid fluorescent materials at virtually any angle to the incident light beam. A 1 kW xenon light source and the use of reflective optics enable the device to make bispectral measurements from the ultraviolet to the near infrared. This paper describes the optical arrangement of the new system..

  19. Conceptual design requirements for Korean Reference HLW disposal System

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Heui Joo; Choi, Jong Won; Hahn, Pil Son; Lee, Jong Youl; Kim, Kyung Soo; Kim, Sung Ki; Cho, Dong Keun; Lee, Yang

    2005-05-15

    This report outlined the requirements for the conceptual design of KRS(Korean Reference HLW disposal System). The site for the disposal of high-level radioactive wastes has not yet been selected in Korea. Since the KRS should be designed under these circumstances, the necessary requirements which should be determined are studied in the report. The amounts of spent fuels from the nuclear power plants in the long-term national power development plan are projected. With this estimation the disposal rates of CANDU and PWR spent fuels are analyzed and determined. The national and international regulations regarding the disposal of HLW are summarized. The functions of the underground facilities are defined. The representative geological conditions are determined since no site is yet decided in Korea.

  20. Radioisotope Power Systems Reference Book for Mission Designers and Planners

    Science.gov (United States)

    Lee, Young; Bairstow, Brian

    2015-01-01

    The RPS Program's Program Planning and Assessment (PPA) Office commissioned the Mission Analysis team to develop the Radioisotope Power Systems (RPS) Reference Book for Mission Planners and Designers to define a baseline of RPS technology capabilities with specific emphasis on performance parameters and technology readiness. The main objective of this book is to provide RPS technology information that could be utilized by future mission concept studies and concurrent engineering practices. A progress summary from the major branches of RPS technology research provides mission analysis teams with a vital tool for assessing the RPS trade space, and provides concurrent engineering centers with a consistent set of guidelines for RPS performance characteristics. This book will be iterated when substantial new information becomes available to ensure continued relevance, serving as one of the cornerstone products of the RPS PPA Office. This book updates the original 2011 internal document, using data from the relevant publicly released RPS technology references and consultations with RPS technologists. Each performance parameter and RPS product subsection has been reviewed and cleared by at least one subject matter representative. A virtual workshop was held to reach consensus on the scope and contents of the book, and the definitions and assumptions that should be used. The subject matter experts then reviewed and updated the appropriate sections of the book. The RPS Mission Analysis Team then performed further updates and crosschecked the book for consistency. Finally, a second virtual workshop was held to ensure all subject matter experts and stakeholders concurred on the contents.

  1. Human Exploration of Mars Design Reference Architecture 5.0

    Science.gov (United States)

    Drake, Bret G.

    2009-01-01

    This document reviews the Design Reference Architecture (DRA) for human exploration of Mars. The DRA represents the current best strategy for human missions. The DRA is not a formal plan, but provides a vision and context to tie current systems and technology developments to potential missions to Mars, and it also serves as a benchmark against which alternative architectures can be measured. The document also reviews the objectives and products of the 2007 study that was to update NASA's human Mars mission reference architecture, assess strategic linkages between lunar and Mars strategies, develop an understanding of methods for reducing cost/risk of human missions through investment in research, technology development and synergy with other exploration plans. There is also a review of the process by which the DRA will continue to be refined. The unique capacities of human exploration is reviewed. The possible goals and objectives of the first three human missions are presented, along with the recommendation that the mission involve a long stay visiting multiple sites.The deployment strategy is outlined and diagrammed including the pre-deployment of the many of the material requirements, and a six crew travel to Mars on a six month trajectory. The predeployment and the Orion crew vehicle are shown. The ground operations requirements are also explained. Also the use of resources found on the surface of Mars is postulated. The Mars surface exploration strategy is reviewed, including the planetary protection processes that are planned. Finally a listing of the key decisions and tenets is posed.

  2. Referred pain patterns provoked on intra-pelvic structures among women with and without chronic pelvic pain : a descriptive study

    OpenAIRE

    Torstensson, Thomas; Butler, Stephen; Lindgren, Anne; Peterson, Magnus; Eriksson, Margaretha; Kristiansson, Per

    2015-01-01

    OBJECTIVES: To describe referred pain patterns provoked from intra-pelvic structures in women with chronic pelvic pain (CPP) persisting after childbirth with the purpose to improve diagnostics and give implications for treatment. MATERIALS AND METHODS: In this descriptive and comparative study 36 parous women with CPP were recruited from a physiotherapy department waiting list and by advertisements in newspapers. A control group of 29 parous women without CPP was consecutively assessed for el...

  3. Practical Design of Delta-Sigma Multiple Description Audio Coding

    DEFF Research Database (Denmark)

    Leegaard, Jack Højholt; Østergaard, Jan; Jensen, Søren Holdt

    2014-01-01

    It was recently shown that delta-sigma quantization (DSQ) can be used for optimal multiple description (MD) coding of Gaussian sources. The DSQ scheme combined oversampling, prediction, and noise-shaping in order to trade off side distortion for central distortion in MD coding. It was shown...

  4. Northern Sotho grammatical descriptions: the design of a tokeniser ...

    African Journals Online (AJOL)

    With tokenisation, this ambiguity is removed as the position of the morpheme in the token allows for more accurate analysis of the morpheme. This article focuses on the description of the verbal segment in current Northern Sotho grammars. The different types of verbal elements are investigated as well as all the verbal ...

  5. Design and Verification of MIMO 2x2 Reference Antennas

    DEFF Research Database (Denmark)

    Szini, Istvan Janos; Pedersen, Gert Frølund; Estrada, J.

    2012-01-01

    The development and initial discussion of a reference MIMO 2×2 antenna concept has been presented in [1]. The reference antenna concept has been created to eliminate the uncertainties linked to the unknown antenna performance of the few LTE MIMO 2×2 reference devices or golden standards currently...

  6. Treatment results in qualitative designs. Application of Descriptive Analysis

    Directory of Open Access Journals (Sweden)

    Héctor Blas Lahitte

    2014-04-01

    It discusses two examples from the Ethology and Psychology, applying methodological strategy Descriptive Analysis. They show that the codification that allows this method takes into account on the one hand, the knowledge base and information relating to a particular disciplinary domain; and on the other hand, it allows to make evident the inferences followed in the reasoning and the rules of interpretation used in reaching new knowledge.

  7. Referred pain patterns provoked on intra-pelvic structures among women with and without chronic pelvic pain: a descriptive study.

    Directory of Open Access Journals (Sweden)

    Thomas Torstensson

    Full Text Available To describe referred pain patterns provoked from intra-pelvic structures in women with chronic pelvic pain (CPP persisting after childbirth with the purpose to improve diagnostics and give implications for treatment.In this descriptive and comparative study 36 parous women with CPP were recruited from a physiotherapy department waiting list and by advertisements in newspapers. A control group of 29 parous women without CPP was consecutively assessed for eligibility from a midwifery surgery. Inclusion criterion for CPP was: moderate pain in the sacral region persisting at least six months after childbirth confirmed by pelvic pain provocation tests. Exclusion criteria in groups with and without CPP were: persistent back or pelvic pain with onset prior to pregnancy, previous back surgery and positive neurological signs. Pain was provoked by palpation of 13 predetermined intra-pelvic anatomical landmarks. The referred pain distribution was expressed in pain drawings and described in pain maps and calculated referred pain areas.Pain provoked by palpation of the posterior intra-pelvic landmarks was mostly referred to the sacral region and pain provoked by palpation of the ischial and pubic bones was mostly referred to the groin and pubic regions, with or without pain referred down the ipsilateral leg. The average pain distribution area provoked by palpation of all 13 anatomical landmarks was 30.3 mm² (19.2 to 53.7 in women with CPP as compared to 3.2 mm² (1.0 to 5.1 in women without CPP, p< 0.0001.Referred pain patterns provoked from intra-pelvic landmarks in women with CPP are consistent with sclerotomal sensory innervation. Magnification of referred pain patterns indicates allodynia and central sensitization. The results suggest that pain mapping can be used to evaluate and confirm the pain experience among women with CPP and contribute to diagnosis.

  8. Towards health care process description framework: an XML DTD design.

    Science.gov (United States)

    Staccini, P; Joubert, M; Quaranta, J F; Aymard, S; Fieschi, D; Fieschi, M

    2001-01-01

    The development of health care and hospital information systems has to meet users needs as well as requirements such as the tracking of all care activities and the support of quality improvement. The use of process-oriented analysis is of-value to provide analysts with: (i) a systematic description of activities; (ii) the elicitation of the useful data to perform and record care tasks; (iii) the selection of relevant decision-making support. But paper-based tools are not a very suitable way to manage and share the documentation produced during this step. The purpose of this work is to propose a method to implement the results of process analysis according to XML techniques (eXtensible Markup Language). It is based on the IDEF0 activity modeling language (Integration DEfinition for Function modeling). A hierarchical description of a process and its components has been defined through a flat XML file with a grammar of proper metadata tags. Perspectives of this method are discussed.

  9. Descriptive Analysis of Single Subject Research Designs: 1983-2007

    Science.gov (United States)

    Hammond, Diana; Gast, David L.

    2010-01-01

    Single subject research methodology is commonly used and cited in special education courses and journals. This article reviews the types of single subject research designs published in eight refereed journals between 1983 and 2007 used to answer applied research questions. Single subject designs were categorized as withdrawal/reversal, time…

  10. Performance Design Study Programme Description Fagmodul i performancedesign

    DEFF Research Database (Denmark)

    2015-01-01

    Lydoptagelse af studieordningsteksten 'fagmodul i performance design'. Til brug ved performativ situation ved semesterstart for fagmodulstuderende efterår 2015. Varighed: 7 min 42 sek.......Lydoptagelse af studieordningsteksten 'fagmodul i performance design'. Til brug ved performativ situation ved semesterstart for fagmodulstuderende efterår 2015. Varighed: 7 min 42 sek....

  11. Referred Pain Patterns Provoked on Intra-Pelvic Structures among Women with and without Chronic Pelvic Pain: A Descriptive Study

    Science.gov (United States)

    Butler, Stephen; Peterson, Magnus; Eriksson, Margaretha

    2015-01-01

    Objectives To describe referred pain patterns provoked from intra-pelvic structures in women with chronic pelvic pain (CPP) persisting after childbirth with the purpose to improve diagnostics and give implications for treatment. Materials and Methods In this descriptive and comparative study 36 parous women with CPP were recruited from a physiotherapy department waiting list and by advertisements in newspapers. A control group of 29 parous women without CPP was consecutively assessed for eligibility from a midwifery surgery. Inclusion criterion for CPP was: moderate pain in the sacral region persisting at least six months after childbirth confirmed by pelvic pain provocation tests. Exclusion criteria in groups with and without CPP were: persistent back or pelvic pain with onset prior to pregnancy, previous back surgery and positive neurological signs. Pain was provoked by palpation of 13 predetermined intra-pelvic anatomical landmarks. The referred pain distribution was expressed in pain drawings and described in pain maps and calculated referred pain areas. Results Pain provoked by palpation of the posterior intra-pelvic landmarks was mostly referred to the sacral region and pain provoked by palpation of the ischial and pubic bones was mostly referred to the groin and pubic regions, with or without pain referred down the ipsilateral leg. The average pain distribution area provoked by palpation of all 13 anatomical landmarks was 30.3 mm² (19.2 to 53.7) in women with CPP as compared to 3.2 mm² (1.0 to 5.1) in women without CPP, ppain patterns provoked from intra-pelvic landmarks in women with CPP are consistent with sclerotomal sensory innervation. Magnification of referred pain patterns indicates allodynia and central sensitization. The results suggest that pain mapping can be used to evaluate and confirm the pain experience among women with CPP and contribute to diagnosis. PMID:25793999

  12. Referred pain patterns provoked on intra-pelvic structures among women with and without chronic pelvic pain: a descriptive study.

    Science.gov (United States)

    Torstensson, Thomas; Butler, Stephen; Lindgren, Anne; Peterson, Magnus; Eriksson, Margaretha; Kristiansson, Per

    2015-01-01

    To describe referred pain patterns provoked from intra-pelvic structures in women with chronic pelvic pain (CPP) persisting after childbirth with the purpose to improve diagnostics and give implications for treatment. In this descriptive and comparative study 36 parous women with CPP were recruited from a physiotherapy department waiting list and by advertisements in newspapers. A control group of 29 parous women without CPP was consecutively assessed for eligibility from a midwifery surgery. Inclusion criterion for CPP was: moderate pain in the sacral region persisting at least six months after childbirth confirmed by pelvic pain provocation tests. Exclusion criteria in groups with and without CPP were: persistent back or pelvic pain with onset prior to pregnancy, previous back surgery and positive neurological signs. Pain was provoked by palpation of 13 predetermined intra-pelvic anatomical landmarks. The referred pain distribution was expressed in pain drawings and described in pain maps and calculated referred pain areas. Pain provoked by palpation of the posterior intra-pelvic landmarks was mostly referred to the sacral region and pain provoked by palpation of the ischial and pubic bones was mostly referred to the groin and pubic regions, with or without pain referred down the ipsilateral leg. The average pain distribution area provoked by palpation of all 13 anatomical landmarks was 30.3 mm² (19.2 to 53.7) in women with CPP as compared to 3.2 mm² (1.0 to 5.1) in women without CPP, ppain patterns provoked from intra-pelvic landmarks in women with CPP are consistent with sclerotomal sensory innervation. Magnification of referred pain patterns indicates allodynia and central sensitization. The results suggest that pain mapping can be used to evaluate and confirm the pain experience among women with CPP and contribute to diagnosis.

  13. Fast tracking ICT infrastructure requirements and design, based on Enterprise Reference Architecture and matching Reference Models

    DEFF Research Database (Denmark)

    Bernus, Peter; Baltrusch, Rob; Vesterager, Johan

    2002-01-01

    The Globemen Consortium has developed the virtual enterprise reference architecture and methodology (VERAM), based on GERAM and developed reference models for virtual enterprise management and joint mission delivery. The planned virtual enterprise capability includes the areas of sales...... and marketing, global engineering, and customer relationship management. The reference models are the basis for the development of ICT infrastructure requirements. These in turn can be used for ICT infrastructure specification (sometimes referred to as 'ICT architecture').Part of the ICT architecture...... is industry-wide, part of it is industry-specific and a part is specific to the domains of the joint activity that characterises the given Virtual Enterprise Network at hand. The article advocates a step by step approach to building virtual enterprise capability....

  14. Staffing by Design: A Methodology for Staffing Reference

    Science.gov (United States)

    Ward, David; Phetteplace, Eric

    2012-01-01

    The growth in number and kind of online reference services has resulted in both new users consulting library research services as well as new patterns of service use. Staffing in-person and virtual reference services desks adequately requires a systematic analysis of patterns of use across service points in order to successfully meet fluctuating…

  15. Design and Principles Enabling the Space Reference FOM

    Science.gov (United States)

    Moeller, Bjoern; Dexter, Dan; Madden, Michael; Crues, Edwin Z.; Garro, Alfredo; Skuratovskiy, Anton

    2017-01-01

    A first complete draft of the Simulation Interoperability Standards Organization (SISO) Space Reference Federation Object Model (FOM) has now been produced. This paper provides some insights into its capabilities and discusses the opportunity for reuse in other domains. The focus of this first version of the standard is execution control, time management and coordinate systems, well-known reference frames, as well as some basic support for physical entities. The biggest part of the execution control is the coordinated start-up process. This process contains a number of steps, including checking of required federates, handling of early versus late joiners, sharing of federation wide configuration data and multi-phase initialization. An additional part of Execution Control is the coordinated and synchronized transition between Run mode, Freeze mode and Shutdown. For time management, several time lines are defined, including real-time, scenario time, High Level Architecture (HLA) logical time and physical time. A strategy for mixing simulations that use different time steps is introduced, as well as an approach for finding common boundaries for fully synchronized freeze. For describing spatial information, a mechanism with a set of reference frames is specified. Each reference frame has a position and orientation related to a parent reference frame. This makes it possible for federates to perform calculations in reference frames that are convenient to them. An operation on the Moon can be performed using lunar coordinates whereas an operation on Earth can be performed using Earth coordinates. At the same time, coordinates in one reference frame have an unambiguous relationship to a coordinate in another reference frame. While the Space Reference FOM is originally being developed for Space operations, the authors believe that many parts of it can be reused for any simulation that has a focus on physical processes with one or more coordinate systems, and require high

  16. Study Design and Cohort Description of DEFIB-WOMEN

    DEFF Research Database (Denmark)

    Pedersen, Susanne S; Nielsen, Jens Cosedis; Riahi, Sam

    2016-01-01

    Disease: Clinical and Psychological outcomes in WOMEN) study to examine gender differences on (1) patient-reported outcomes (PROs), (2) procedure- and device-related complications, and (3) ventricular tachyarrhythmia and mortality. This presents the study design and baseline characteristics of the cohort....... METHODS: DEFIB-WOMEN is a national, multicenter, prospective, observational study. First-time implanted patients are asked to complete PROs at several time points. Information on baseline and follow-up characteristics are captured from patients' medical records, purpose-designed questions, and the Danish...

  17. A European Drought Reference Database: Design and Online Implementation

    NARCIS (Netherlands)

    Stagge, J.H.; Tallaksen, L.M.; Kohn, I.; Stahl, K.; Loon, van A.

    2013-01-01

    This report presents the structure and status of the online European Drought Reference (EDR) database. This website provides detailed historical information regarding major historical European drought events. Each drought event is summarized using climatological drought indices, hydrological drought

  18. Domain-specific language design requires feature descriptions

    NARCIS (Netherlands)

    A. van Deursen (Arie); P. Klint (Paul)

    2001-01-01

    textabstractA domain-specific language (DSL) provides a notation tailored towards an application domain and is based on the relevant concepts and features of that domain. As such, a DSL is a means to describe and generate members of a family of programs in the domain. A prerequisite for the design

  19. 2001 - 2010 Danish design reference year. Reference climate dataset for technical dimensioning in building, construction and other sectors

    Energy Technology Data Exchange (ETDEWEB)

    Grunnet Wang, P.; Scharling, M.; Pagh Nielsen, K.; Kern-Hansen, C. [Danish Meteorological Institute (DMI), Copenhagen (Denmark); Wittchen, K.B. [Aalborg Univ., Danish Building Research Institute (SBi), Copenhagen (Denmark)

    2013-09-15

    This report presents the Danish Design Reference Year based on observed data from 2001 - 2010. In various sectors - i.e. building and construction, energy, etc. - the climate and weather usually plays a part in a given project. The Danish Design Reference Year dataset is a collection of data series for eleven specific parameters, that each represents a typical year in Denmark. The uses of the dataset may vary from simulations to statistical analysis, graphical overviews etc. The Danish land areas have been sectionalised into five to six climatological zones depending on the parameter, each characterized by distinct diurnal and yearly variations. The dataset consists of observed data from one station located within and representing each zone. In addition to the complete Danish Design Reference Year dataset, a subset specifically selected to be used for energy performance calculations for obtaining a building permit is included. (Author)

  20. Forest landscape description and inventories - a basis for landplanning and design

    Science.gov (United States)

    R. Burton Litton

    1968-01-01

    Describes six analytical factors and seven compositional types useful in recognition and description of scenic resources. Illustrates their application in two inventories made to aid managers and landscape architects in planning and design.

  1. System design description for surface moisture measurement system (SMMS)

    Energy Technology Data Exchange (ETDEWEB)

    Vargo, G.F.

    1996-09-23

    The SMMS has been developed to measure moisture in the top few centimeters of tank waste. The SMMS development was initiated by the preliminary findings of SAR-033, and does not necessarily fulfill any established DQO. After the SAR-033 is released, if no significant changes are made, moisture measurements in the organic waste tanks will rapidly become a DQO. The SMMS was designed to be installed in any 4 inch or larger riser, and to allow maximum adjustability for riser lengths, and is used to deploy a sensor package on the waste surface within a 6 foot radius about the azimuth. The first sensor package will be a neutron probe.

  2. SWEPP Gamma-Ray Spectrometer System software design description

    Energy Technology Data Exchange (ETDEWEB)

    Femec, D.A.; Killian, E.W.

    1994-08-01

    To assist in the characterization of the radiological contents of contract-handled waste containers at the Stored Waste Examination Pilot Plant (SWEPP), the SWEPP Gamma-Ray Spectrometer (SGRS) System has been developed by the Radiation Measurements and Development Unit of the Idaho National Engineering Laboratory. The SGRS system software controls turntable and detector system activities. In addition to determining the concentrations of gamma-ray-emitting radionuclides, this software also calculates attenuation-corrected isotopic mass ratios of-specific interest. This document describes the software design for the data acquisition and analysis software associated with the SGRS system.

  3. An Earth-Moon System Trajectory Design Reference Catalog

    Science.gov (United States)

    Folta, David; Bosanac, Natasha; Guzzetti, Davide; Howell, Kathleen C.

    2014-01-01

    As demonstrated by ongoing concept designs and the recent ARTEMIS mission, there is, currently, significant interest in exploiting three-body dynamics in the design of trajectories for both robotic and human missions within the Earth-Moon system. The concept of an interactive and 'dynamic' catalog of potential solutions in the Earth-Moon system is explored within this paper and analyzed as a framework to guide trajectory design. Characterizing and compiling periodic and quasi-periodic solutions that exist in the circular restricted three-body problem may offer faster and more efficient strategies for orbit design, while also delivering innovative mission design parameters for further examination.

  4. System design description for GCFR-core flow test loop

    Energy Technology Data Exchange (ETDEWEB)

    Huntley, W.R.; Grindell, A.G.

    1980-12-01

    The Core Flow Test Loop is a high-pressure, high-temperature, out-of-reactor helium circulation system that is being constructed to permit detailed study of the thermomechanical and thermal performance at prototypic steady-state and transient operating conditions of simulated segments of core assemblies for a GCFR Demonstration Plant, as designed by General Atomic Company. It will also permit the expermental verification of predictive analytical models of the GCFR core assemblies needed to reduce operational and safety uncertainties of the GCFR. Full-sized blanket assemblies and segments of fuel rod and control rod fuel assemblies will be simulated with test bundles of electrically powered fuel rod or blanket rod simulators. The loop will provide the steady-state and margin test requirements of bundle power and heat removal, and of helium coolant flow rate, pressure, and temperature for test bundles having up to 91 rods; these requirements set the maximum power, coolant helium flow, and thermal requirements for the loop. However, the size of the test vessel that contains the test bundles will be determined by the bundles that simulate a full-sized GCFR blanket assembly. The loop will also provide for power and coolant transients to simulate transient operation of GCFR core assemblies, including the capability for rapid helium depressurization to simulate the depressurization class of GCFR accidents. In addition, the loop can be used as an out-of-reactor test bed for characterizing in-reactor test bundle configurations.

  5. Contested collaboration: A descriptive model of intergroup communication in information system design

    DEFF Research Database (Denmark)

    Sonnenwald, D.H.

    1995-01-01

    to design outcomes. Through a qualitative analysis of a house, expert system, and telecommunications network architecture and management system design situations, a descriptive model of design that characterizes communication among users, designers, and developers as they create an artifact was developed....... The model describes design phases, roles, themes, and intergroup communication networks as they evolve throughout the design process and characterizes design as a process of ''contested collaboration.'' It is a first step towards a predictive design model that suggests strategies which may help participants...

  6. A micrometeoroid deceleration and capture experiment: Conceptual experiment design description

    Science.gov (United States)

    Wolfe, J. H.; Ballard, R. W.; Carle, G. C.; Bunch, T. E.

    1986-01-01

    The preliminary conceptual design for a cosmic dust collector is described. For the case of low Earth orbit (LEO), dust particles enter the collector through the collimator at a few volts negative potential due to charging in the ionosphere, at a velocity of 1 to 50 km/sec. The particles then pass through an electron stream and are charged to about 1 KV negative (regardless of incoming polarity). The 1 KV negatively charged particle then passes through three sensing grids coupled to charge sensitive preamps (CSP). The comparison of the two pulses provided by S(1) and S(2) are utilized by the microprocessor to determine the charge, q, on the particle (pulse amplitude) and its velocity, v (by time of flight). The third sensing grid, S(3), is kept at about 20 KV negative so that the dust particle will now be decelerated in passing from S(2) (zero potential) to S(3). S(3) is capacitively coupled to its CSP and the pulse from S(3) is utilized by the microprocessor to determine the particle's energy, E, and therefore its mass, m (again by time of flight) by comparison with the pulses from S(1) and S(2). The microprocessor can now precisely program the high-voltage switching network for the proper timing in the grounding of the successive deceleration grids. As determined by the microprocessor, each successive deceleration grid is grounded just after the dust particle passes, thus reducing the particle's energy by the amount q*100 KV at each stage. The microprocessor also determines at which stage the particle will fall below a certain critical energy where all remaining grids remain unswitched so that the particle will drift to the collector. The collector is kept at about 100V positive and is covered with gold foil to eliminate contamination and is removable for subsequent return to earth for detailed analysis.

  7. WRAP Module 1 data management system (DMS) software design description (SDD)

    Energy Technology Data Exchange (ETDEWEB)

    Weidert, J.R. [Westinghouse Hanford Co., Richland, WA (United States)

    1996-05-13

    Revision 2 of the Waste Receiving and Processing (WRAP) Module 1 Data Management System (DMS) Preliminary Software Design Description (PSDD) provides a high-level design description of the system. The WRAP 1 DMS is required to collect, store, and report data related to certification, tracking, packaging, repackaging, processing, and shipment of waste processed or stored at the WRAP 1 facility. The WRAP 1 DMS SDD is used as the primary medium for communication software design information. This release provides design descriptions for the following process modules produced under Phase 1 of the development effort: Receiving Drum or Box Containers Process Routing and Picklists; Waste Inventory by Location and/or Container Relationships; LLW Process Glovebox Facility Radiologic Material Inventory Check (partial); Shipping (partial production); Drum or Box NDE Operations; and Drum or Box NDA Operations Data Review (partial production). In addition, design descriptions are included for the following process modules scheduled for development under Phases 2 and 3: Activity Comment; LLW RWM Glovebox Sample Management; TRU Process Glovebox; TRU RWM Glovebox; and TRUPACT Processing. Detailed design descriptions for Reports and Facility Metrics have also been provided for in Revision 2 of this document.

  8. System design description for the SY-101 hydrogen mitigation test project data acquisition and control system (DACS-1)

    Energy Technology Data Exchange (ETDEWEB)

    Ermi, A.M.

    1998-03-02

    There is no new activity or procedure associated with the updating of this reference document. The updating of this system design description maintains an agreed upon documentation program initiated within the test program and carried into operations at time of turnover to maintain configuration control as outlined by design authority practicing guidelines. Any changes made to controlled components in the field will be updated after the time of implementation to support the engineers and operators understand, maintain, train to and operate the system. There are no new credible failure modes associated with the updating of information in a support description document. The failure analysis of each change was reviewed at the time of implementation of the Systems Change Request for all the processes changed. This document simply provides a history of implementation and current system status. The incorporation of the two documents, Computer Systems Design Description (HNF-SD-WMCSDD-008) and the Input/Output Channel List (HNF-SD-WM-EL-001), as appendices allow for fewer errors in changes. Because the documents are all together, they will be approved as one document, not three separate entities which could be updated at different times, creating a situation which does not accurately depict field conditions.

  9. System design description for the consolidated sludge sampling system for K Basins floor and fuel canisters

    Energy Technology Data Exchange (ETDEWEB)

    HECHT, S.L.

    1999-02-18

    This System Design Description describes the Consolidated Sludge Sampling System used in the gathering of sludge samples from K Basin floor and fuel canisters. This document provides additional information on the need for the system, the functions and requirements of the systems, the operations of the system, and the general work plan used in its' design and development.

  10. Design reference year for development of photovoltaic envelope systems

    Science.gov (United States)

    Mihalka, Peter; Matiasovsky, Peter

    2017-07-01

    An application of photovoltaic cells on external surfaces of building envelope represents a development of new construction element. A mutual coupling between thermal behaviour of photovoltaic layer and the other layers of the structure, with special properties, requires a specific selection of the characteristic outdoor thermal boundary conditions, necessary for optimum design of the envelope from the aspect of structure, material composition and geometry. The main design criteria are the effectiveness and elimination of overheating of photovoltaic module and the optimisation of heat distribution in the envelope structure during particular year seasons. The paper contains the results of the analysis of time courses of climatic elements during a real year as the boundary conditions for simulation of photovoltaic integrated building envelope systems, used in simulations of thermal behaviour of photovoltaics integrated with building envelope systems.

  11. Spintronic Memristor Based Temperature Sensor Design with CMOS Current Reference

    Science.gov (United States)

    2012-03-01

    studied. BJT transistor is usually favored by designers. The most popular method is utilizing the difference between base-emitter voltages of a...substrate BJT transistor to detect temperature changes [18][20]. To make up the non-perfect linearity of BJT transistor , many curvature correction...the traditional temperature sensors, the key components for temperature detection are p-n junction diode [25] or transistor [17], which have been well

  12. Design of Low Complexity Model Reference Adaptive Controllers

    Science.gov (United States)

    Hanson, Curt; Schaefer, Jacob; Johnson, Marcus; Nguyen, Nhan

    2012-01-01

    Flight research experiments have demonstrated that adaptive flight controls can be an effective technology for improving aircraft safety in the event of failures or damage. However, the nonlinear, timevarying nature of adaptive algorithms continues to challenge traditional methods for the verification and validation testing of safety-critical flight control systems. Increasingly complex adaptive control theories and designs are emerging, but only make testing challenges more difficult. A potential first step toward the acceptance of adaptive flight controllers by aircraft manufacturers, operators, and certification authorities is a very simple design that operates as an augmentation to a non-adaptive baseline controller. Three such controllers were developed as part of a National Aeronautics and Space Administration flight research experiment to determine the appropriate level of complexity required to restore acceptable handling qualities to an aircraft that has suffered failures or damage. The controllers consist of the same basic design, but incorporate incrementally-increasing levels of complexity. Derivations of the controllers and their adaptive parameter update laws are presented along with details of the controllers implementations.

  13. A reference pelton turbine - design and efficiency measurements

    Science.gov (United States)

    Solemslie, Bjørn W.; Dahlhaug, Ole G.

    2014-03-01

    The Pelton turbine has been subject to a varying degree of research interest since the debut of the technology over a century ago. Despite its age there are gaps in the knowledge concerning the flow mechanisms effecting the flow through the turbine. A Pelton turbine has been designed at the Waterpower Laboratory at NTNU. This has been done in connection to a Ph.D. project focusing on the flow in Pelton turbine buckets. The design of the turbine has been conducted using in-house knowledge in addition to some comments from a turbine producer. To describe the geometry multiple Bezier curves were used and the design strategy aimed to give a smooth and continuous gradient along the main flow directions in the bucket. The turbine has been designed for the operational conditions of the Pelton test rig installed at the Waterpower Laboratory which is a horizontal single jet test rig with a jet diameter(ds) of 35 mm. The diameter(D) of the runner was set to 513 mm and the width(W) of a bucket 114 mm, leading to a D/W ratio of 4.5. Manufacturing of the turbine has been carried out in aluminium and the turbine has undergone efficiency testing and visual inspection during operation at a head of 70 m. The turbine did not performed as expected and the maximum efficiency was found to be 77.75%. The low efficiency is mainly caused by a large amount of water leaving the bucket through the lip and hence transferring close to zero of its energy to the shaft. The reason for the large lip loss is discussed and two possible causes are found; the jet is located too close to the lip, and the inner surface of the bucket does not lead the water away from the lip. The turbine geometry and all data from both measurements and simulations will be available upon request in an effort to increase the amount of available data concerning Pelton turbines.

  14. Large Synoptic Survey Telescope: From Science Drivers to Reference Design

    Energy Technology Data Exchange (ETDEWEB)

    Ivezic, Z.; Axelrod, T.; Brandt, W.N.; Burke, D.L.; Claver, C.F.; Connolly, A.; Cook, K.H.; Gee, P.; Gilmore, D.K.; Jacoby, S.H.; Jones, R.L.; Kahn, S.M.; Kantor, J.P.; Krabbendam, V.; Lupton, R.H.; Monet, D.G.; Pinto, P.A.; Saha, A.; Schalk, T.L.; Schneider, D.P.; Strauss, Michael A.; /Washington U., Seattle, Astron. Dept. /LSST Corp. /Penn State U., Astron. Astrophys. /KIPAC, Menlo Park /NOAO, Tucson /LLNL, Livermore /UC, Davis /Princeton U., Astrophys. Sci. Dept. /Naval Observ., Flagstaff /Arizona U., Astron. Dept. - Steward Observ. /UC, Santa Cruz /Harvard U. /Johns Hopkins U. /Illinois U., Urbana

    2011-10-14

    In the history of astronomy, major advances in our understanding of the Universe have come from dramatic improvements in our ability to accurately measure astronomical quantities. Aided by rapid progress in information technology, current sky surveys are changing the way we view and study the Universe. Next-generation surveys will maintain this revolutionary progress. We focus here on the most ambitious survey currently planned in the visible band, the Large Synoptic Survey Telescope (LSST). LSST will have unique survey capability in the faint time domain. The LSST design is driven by four main science themes: constraining dark energy and dark matter, taking an inventory of the Solar System, exploring the transient optical sky, and mapping the Milky Way. It will be a large, wide-field ground-based system designed to obtain multiple images covering the sky that is visible from Cerro Pachon in Northern Chile. The current baseline design, with an 8.4 m (6.5 m effective) primary mirror, a 9.6 deg{sup 2} field of view, and a 3,200 Megapixel camera, will allow about 10,000 square degrees of sky to be covered using pairs of 15-second exposures in two photometric bands every three nights on average. The system is designed to yield high image quality, as well as superb astrometric and photometric accuracy. The survey area will include 30,000 deg{sup 2} with {delta} < +34.5{sup o}, and will be imaged multiple times in six bands, ugrizy, covering the wavelength range 320-1050 nm. About 90% of the observing time will be devoted to a deep-wide-fast survey mode which will observe a 20,000 deg{sup 2} region about 1000 times in the six bands during the anticipated 10 years of operation. These data will result in databases including 10 billion galaxies and a similar number of stars, and will serve the majority of science programs. The remaining 10% of the observing time will be allocated to special programs such as Very Deep and Very Fast time domain surveys. We describe how the

  15. Large Synoptic Survey Telescope: From science drivers to reference design

    Directory of Open Access Journals (Sweden)

    Ivezić Ž.

    2008-01-01

    Full Text Available In the history of astronomy, major advances in our understanding of the Universe have come from dramatic improvements in our ability to accurately measure astronomical quantities. Aided by rapid progress in information technology, current sky surveys are changing the way we view and study the Universe. Next- generation surveys will maintain this revolutionary progress. We focus here on the most ambitious survey currently planned in the visible band, the Large Synoptic Survey Telescope (LSST. LSST will have unique survey capability in the faint time domain. The LSST design is driven by four main science themes: constraining dark energy and dark matter, taking an inventory of the Solar System, exploring the transient optical sky, and mapping the Milky Way. It will be a large, wide-field ground-based system designed to obtain multiple images covering the sky that is visible from Cerro Pachon in Northern Chile. The current baseline design, with an 8.4 m (6.5 m effective primary mirror, a 9.6 deg2 field of view, and a 3,200 Megapixel camera, will allow about 10,000 square degrees of sky to be covered using pairs of 15-second exposures in two photometric bands every three nights on average. The system is designed to yield high image quality, as well as superb astrometric and photometric accuracy. The survey area will include 30,000 deg2 with δ < +34.5◦ , and will be imaged multiple times in six bands, ugrizy, covering the wavelength range 320-1050 nm. About 90% of the observing time will be devoted to a deep- wide-fast survey mode which will observe a 20,000 deg2 region about 1000 times in the six bands during the anticipated 10 years of operation. These data will result in databases including 10 billion galaxies and a similar number of stars, and will serve the majority of science programs. The remaining 10% of the observing time will be allocated to special programs such as Very Deep and Very Fast time domain surveys. We describe how the LSST

  16. Large Synoptic Survey Telescope: From Science Drivers To Reference Design

    Directory of Open Access Journals (Sweden)

    Ivezić, Ž.

    2008-06-01

    Full Text Available In the history of astronomy, major advances in our understanding of the Universe have come from dramatic improvements in our ability to accurately measure astronomical quantities. Aided by rapid progress in information technology, current sky surveys are changing the way we view and study the Universe. Next-generation surveys will maintain this revolutionary progress. We focus here on the most ambitious survey currently planned in the visible band, the Large Synoptic Survey Telescope (LSST. LSST will have unique survey capability in the faint time domain. The LSST design is driven by four main science themes: constraining dark energy and dark matter, taking an inventory of the Solar System, exploring the transient optical sky, and mapping the Milky Way. It will be a large, wide-field ground-based system designed to obtain multiple images covering the sky that is visible from Cerro Pach'{o}n in Northern Chile. The current baseline design, with an 8.4, m (6.5, m effective primary mirror, a 9.6 deg$^2$ field of view, and a 3,200 Megapixel camera, will allow about 10,000 square degrees of sky to be covered using pairs of 15-second exposures in two photometric bands every three nights on average. The system is designed to yield high image quality, as well as superb astrometric and photometric accuracy. The survey area will include 30,000 deg$^2$ with $delta<+34.5^circ$, and will be imaged multiple times in six bands, $ugrizy$, covering the wavelength range 320--1050 nm. About 90\\% of the observing time will be devoted to a deep-wide-fast survey mode which will observe a 20,000 deg$^2$ region about 1000 times in the six bands during the anticipated 10 years of operation. These data will result in databases including 10 billion galaxies and a similar number of stars, and will serve the majority of science programs. The remaining 10\\% of the observing time will be allocated to special programs such as Very Deep and Very Fast time domain surveys. We

  17. Saphyr: a code system from reactor design to reference calculations

    Energy Technology Data Exchange (ETDEWEB)

    Akherraz, B.; Baudron, A.M.; Buiron, L.; Coste-Delclaux, M.; Fedon-Magnaud, C.; Lautard, J.J.; Moreau, F.; Nicolas, A.; Sanchez, R.; Zmijarevic, I. [CEA Saclay, Direction de l' Energie Nucleaire, Departement de Modelisation des Systemes et Structures, Service d' Etudes des Reacteurs et de Modelisation Avancee (DENDMSS/SERMA), 91 - Gif sur Yvette (France); Bergeron, A.; Caruge, D.; Fillion, P.; Gallo, D.; Royer, E. [CEA Saclay, Direction de l' Energie Nucleaire, Departement de Modelisation des Systemes et Structures, Service Fluides numeriques, Modelisations et Etudes (DEN/DMSS/SFNME), 91 - Gif sur Yvette (France); Loubiere, S. [CEA Saclay, Direction de l' Energie Nucleaire, Direction de la Simulation et des Outils Experimentaux, 91- Gif sur Yvette (France)

    2003-07-01

    In this paper we briefly present the package SAPHYR (in French Advanced System for Reactor Physics) which is devoted to reactor calculations, safety analysis and design. This package is composed of three main codes: APOLLO2 for lattice calculations, CRONOS2 for whole core neutronic calculations and FLICA4 for thermohydraulics. Thanks to a continuous development effort, the SAPHYR system is an outstanding tool covering a large domain of applications, from sophisticated 'research and development' studies that need state-of-the-art methodology to routine industrial calculations for reactor and criticality analysis. SAPHYR is powerful enough to carry out calculations for all types of reactors and is invaluable to understand complex phenomena. SAPHYR components are in use in various nuclear companies such as 'Electricite de France', Framatome-ANP, Cogema, SGN, Transnucleaire and Technicatome. Waiting for the next generation tools (DESCARTES for neutronics and NEPTUNE for thermohydraulics) to be available for such a variety of use, with a better level of flexibility and at least equivalent validation and qualification level, the improvement of SAPHYR is going on, to acquire new functions constantly required by users and to improve current performance levels.

  18. Reference design for the standard mirror hybrid reactor

    Energy Technology Data Exchange (ETDEWEB)

    Bender, D.J.; Fink, J.H.; Galloway, T.R.; Kastenberg, W.E.; Lee, J.D.; Devoto, R.S.; Neef, W.S. Jr.; Schultz, K.R.; Culver, D.W.; Rao, S.B.; Rao, S.R.

    1978-05-22

    This report describes the results of a two-year study by Lawrence Livermore Laboratory and General Atomic Co. to develop a conceptual design for the standard (minimum-B) mirror hybrid reactor. The reactor parameters have been chosen to minimize the cost of producing nuclear fuel (/sup 239/Pu) for consumption in fission power reactors (light water reactors). The deuterium-tritium plasma produces approximately 400 MW of fusion power with a plasma Q of 0.64. The fast-fission blanket, which is fueled with depleted uranium and lithium, generates sufficient tritium to run the reactor, has a blanket energy multiplication of M = 10.4, and has a net fissile breeding ratio of Pu/n = 1.51. The reactor has a net electrical output of 600 MWe, a fissile production of 2000 kg of plutonium per year (at a capacity factor of 0.74), and a net plant efficiency of 0.18. The plasma-containment field is generated by a Yin-Yang magnet using NbTi superconductor, and the neutral beam system uses positive-ion acceleration with beam direct conversion. The spherical blanket is based on gas-cooled fast reactor technology. The fusion components, blanket, and primary heat-transfer loop components are all contained within a prestressed-concrete reactor vessel, which provides magnet restraint and supports the primary heat-transfer loop and the blanket.

  19. Architectural design proposal for a Martian base to continue NASA Mars Design Reference Mission

    Science.gov (United States)

    Kozicki, Janek

    The issue of extraterrestrial bases has recently been a very vivid one. There are orbital stations currently existing and humans will travel to Mars around 2030. They will need stations established there, which will provide them the proper living conditions. Firstly, it might be a small module brought from Earth (e.g. NASA Mars Design Reference Mission module (DRM)), in later stages equivalents of Earth houses may be built from local resources. The goal of this paper is to propose an architectural design for an intermediate stage — for a larger habitable unit transported from Earth. It is inspired by terrestrial portable architecture ideas. A pneumatic structure requires small volume during transportation. However, it provides large habitable space after deployment. It is designed for transport by DRM transportation module and its deployment is considerable easy and brief. An architectural solution analogous to a terrestrial house with a studio and a workshop was assumed. Its form was a result of technical and environmental limitations, and the need for an ergonomic interior. The spatial placement of following zones was carefully considered: residential, agricultural and science, as well as a garage with a workshop, transportation routes, and a control and communication center. The issues of Life Support System, energy, food, water and waste recycling were also discussed. This Martian base was designed to be crewed by a team of eight people to stay on Mars for at least 1.5 year. An Open Plan architectural solution was assumed in pneumatic modules, with a high level of modularity. Walls of standardized sizes with zip-fasteners allow free rearrangement of the interior to adapt to a new situation (e.g. damage of one of the pneumatic modules or a psychological ,,need of a change"). The architectural design focuses on ergonomic and psychological aspects of longer stay in hostile Martian environment. This solution provides Martian crew with a comfortable habitable

  20. HYBRID SULFUR PROCESS REFERENCE DESIGN AND COST ANALYSIS

    Energy Technology Data Exchange (ETDEWEB)

    Gorensek, M.; Summers, W.; Boltrunis, C.; Lahoda, E.; Allen, D.; Greyvenstein, R.

    2009-05-12

    This report documents a detailed study to determine the expected efficiency and product costs for producing hydrogen via water-splitting using energy from an advanced nuclear reactor. It was determined that the overall efficiency from nuclear heat to hydrogen is high, and the cost of hydrogen is competitive under a high energy cost scenario. It would require over 40% more nuclear energy to generate an equivalent amount of hydrogen using conventional water-cooled nuclear reactors combined with water electrolysis compared to the proposed plant design described herein. There is a great deal of interest worldwide in reducing dependence on fossil fuels, while also minimizing the impact of the energy sector on global climate change. One potential opportunity to contribute to this effort is to replace the use of fossil fuels for hydrogen production by the use of water-splitting powered by nuclear energy. Hydrogen production is required for fertilizer (e.g. ammonia) production, oil refining, synfuels production, and other important industrial applications. It is typically produced by reacting natural gas, naphtha or coal with steam, which consumes significant amounts of energy and produces carbon dioxide as a byproduct. In the future, hydrogen could also be used as a transportation fuel, replacing petroleum. New processes are being developed that would permit hydrogen to be produced from water using only heat or a combination of heat and electricity produced by advanced, high temperature nuclear reactors. The U.S. Department of Energy (DOE) is developing these processes under a program known as the Nuclear Hydrogen Initiative (NHI). The Republic of South Africa (RSA) also is interested in developing advanced high temperature nuclear reactors and related chemical processes that could produce hydrogen fuel via water-splitting. This report focuses on the analysis of a nuclear hydrogen production system that combines the Pebble Bed Modular Reactor (PBMR), under development by

  1. WRAP Module 1 data management system (DMS) software design description (SDD)

    Energy Technology Data Exchange (ETDEWEB)

    Talmage, P.A.

    1995-03-17

    The Waste Receiving and Processing (WRAP) Module 1 Data Management System (DMS) System Design Description (SDD) describes the logical and physical architecture of the system. The WRAP 1 DMS SDD formally partitions the elements of the system described in the WRAP 1 DMS Software requirements specification into design objects and describes the key properties and relationships among the design objects and interfaces with external systems such as the WRAP Plant Control System (PCS). The WRAP 1 DMS SDD can be thought of as a detailed blueprint for implementation activities. The design descriptions contained within this document will describe, in detail, the software products that will be developed to assist the Project W-026, Waste Receiving and Processing Module 1, in their management functions. The WRAP 1 DMS is required to collect, store, and report data related to certification, tracking, packaging, repackaging, processing, and shipment of waste processed or stored at the WRAP 1 facility.

  2. 78 FR 48631 - Descriptive Designation for Needle- or Blade-Tenderized (Mechanically Tenderized) Beef Products

    Science.gov (United States)

    2013-08-09

    ... Listserv, a free electronic mail subscription service for industry, trade groups, consumer interest groups... Food Safety and Inspection Service 9 CFR Part 317 Descriptive Designation for Needle- or Blade-Tenderized (Mechanically Tenderized) Beef Products AGENCY: Food Safety and Inspection Service, USDA. ACTION...

  3. FAST FLUX TEST FACILITY CONCEPTUAL SYSTEM DESIGN DESCRIPTION FOR THE BUILDING ELECTRICAL POWER SYSTEM No. 12

    Energy Technology Data Exchange (ETDEWEB)

    None

    1968-07-03

    The Building Electrical Power System, transmits, distributes and controls the electrical power utilized by the equipment of all of the FFTF system. Included are system functions and design requirements, the physical description of the system, safety considerations, principles of operations, and maintenance principles.

  4. FAST FLUX TEST FACILITY CONCEPTUAL SYSTEM DESIGN DESCRIPTION FOR THE HEATING AND VENTILATION SYSTEM NO. 25

    Energy Technology Data Exchange (ETDEWEB)

    None

    1969-12-05

    The Heating and Ventilation System provides the atmospheric conditions in FFTF as required to assure that plant objectives can be met in a safe and practical manner. Included are functions and design requirements, a physical description of the system, safety considerations, principles of operation, and maintenance principles.

  5. Cold Vacuum Drying facility civil structural system design description (SYS 06)

    Energy Technology Data Exchange (ETDEWEB)

    PITKOFF, C.C.

    1999-07-06

    This document describes the Cold Vacuum Drying (CVD) Facility civil - structural system. This system consists of the facility structure, including the administrative and process areas. The system's primary purpose is to provide for a facility to house the CVD process and personnel and to provide a tertiary level of containment. The document provides a description of the facility and demonstrates how the design meets the various requirements imposed by the safety analysis report and the design requirements document.

  6. Test Design Description (TDD). Volume 1A. Design description and safety analysis for IFR-1 metal fuels irradiation test in FFTF

    Energy Technology Data Exchange (ETDEWEB)

    Tsai, H.; Neimark, L. A.; Billone, M. C.; Fryer, R. M.; Koenig, J. F.; Lehto, W. K.; Malloy, D. J.

    1986-01-01

    A steady-state irradiation experiment on metal fuels, designated IFR-1, will be conducted in the FTR. The purpose of the experiment is to support the development of metal fuels for the Integral Fast Reactor (IFR) program. The main objective of the IFR-1 test is to generate integral fuel performance data for full-length metal fuels. The effect of fuel column length on the integral behavior of metal fuels will be evaluated by comparing the results of the IFR-1 test with those of the EBR-II tests conducted under similar power and temperature conditions. This document describes the IFR-1 metal fuel irradiation experiment and provides the test requirements and supporting steady-state, transient and safety analyses as required by the User`s Guide for the Irradiation of Experiments in the FTR [1] for Test Design Description Volume 1A. 40 refs.

  7. A Process Framework for Designing Software Reference Architectures for Providing Tools as a Service

    DEFF Research Database (Denmark)

    Chauhan, Muhammad Aufeef; Babar, Muhammad Ali; Probst, Christian W.

    2016-01-01

    of software systems need customized and systematic SRA design and evaluation methods. In this paper, we present a software Reference Architecture Design process Framework (RADeF) that can be used for analysis, design and evaluation of the SRA for provisioning of Tools as a Service as part of a cloud...

  8. ATM Technology Demonstration-1 Phase II Boeing Configurable Graphical Display (CGD) Software Design Description

    Science.gov (United States)

    Wilber, George F.

    2017-01-01

    This Software Description Document (SDD) captures the design for developing the Flight Interval Management (FIM) system Configurable Graphics Display (CGD) software. Specifically this SDD describes aspects of the Boeing CGD software and the surrounding context and interfaces. It does not describe the Honeywell components of the CGD system. The SDD provides the system overview, architectural design, and detailed design with all the necessary information to implement the Boeing components of the CGD software and integrate them into the CGD subsystem within the larger FIM system. Overall system and CGD system-level requirements are derived from the CGD SRS (in turn derived from the Boeing System Requirements Design Document (SRDD)). Display and look-and-feel requirements are derived from Human Machine Interface (HMI) design documents and working group recommendations. This Boeing CGD SDD is required to support the upcoming Critical Design Review (CDR).

  9. Updated reference design of a liquid metal cooled tandem mirror fusion breeder

    Energy Technology Data Exchange (ETDEWEB)

    Berwald, D.H.; Whitley, R.H.; Garner, J.K.; Gromada, R.J.; McCarville, T.J.; Moir, R.W.; Lee, J.D.; Bandini, B.R.; Fulton, F.J.; Wong, C.P.C.; Maya, I.; Hoot, C.G.; Schultz, K.R.; Miller, L.G.; Beeston, J.M.; Harris, B.L.; Westman, R.A.; Ghoniem, N.M.; Orient, G.; Wolfer, M.; DeVan, J.H.; Torterelli, P.

    1985-09-01

    Detailed studies of key techinical issues for liquid metal cooled fusion breeder (fusion-fission hybrid blankets) have been performed during the period 1983-4. Based upon the results of these studies, the 1982 reference liquid metal cooled tandem mirror fusion breeder blanket design was updated and is described. The updated reference blankets provides increased breeding and lower technological risk in comparison with the original reference blanket. In addition to the blanket design revisions, a plant concept, cost, and fuel cycle economics assessment is provided. The fusion breeder continues to promise an economical source of fissile fuel for the indefinite future.

  10. A domain-independent descriptive design model and its application to structured reflection on design processes

    NARCIS (Netherlands)

    Reymen, Isabelle; Hammer, D.K.; Kroes, P.A.; van Aken, Joan Ernst; van Aken, J.E.; Dorst, C.H.; Bax, M.F.T.; Basten, T

    2006-01-01

    Domain-independent models of the design process are an important means for facilitating interdisciplinary communication and for supporting multidisciplinary design. Many so-called domain-independent models are, however, not really domain independent. We state that to be domain independent, the

  11. A Process Framework for Designing Software Reference Architectures for Providing Tools as a Service

    DEFF Research Database (Denmark)

    Chauhan, Muhammad Aufeef; Babar, Muhammad Ali; Probst, Christian W.

    2016-01-01

    Software Reference Architecture (SRA), which is a generic architecture solution for a specific type of software systems, provides foundation for the design of concrete architectures in terms of architecture design guidelines and architecture elements. The complexity and size of certain types...... of software systems need customized and systematic SRA design and evaluation methods. In this paper, we present a software Reference Architecture Design process Framework (RADeF) that can be used for analysis, design and evaluation of the SRA for provisioning of Tools as a Service as part of a cloud......-enabled workSPACE (TSPACE). The framework is based on the state of the art results from literature and our experiences with designing software architectures for cloud-based systems. We have applied RADeF SRA design two types of TSPACE: software architecting TSPACE and software implementation TSPACE...

  12. Scaffolding Students' Development of Creative Design Skills: A Curriculum Reference Model

    Science.gov (United States)

    Lee, Chien-Sing; Kolodner, Janet L.

    2011-01-01

    This paper provides a framework for promoting creative design capabilities in the context of achieving community goals pertaining to sustainable development among high school students. The framework can be used as a reference model to design formal or out-of-school curriculum units in any geographical region. This theme is chosen due to its…

  13. A Process Framework for Designing Software Reference Architectures for Providing Tools as a Service

    DEFF Research Database (Denmark)

    Chauhan, Muhammad Aufeef; Babar, Muhammad Ali; Probst, Christian W.

    2016-01-01

    to be provisioned and underlying cloud platforms to be used while designing SRA. The framework recommends adoption of the multi-faceted approach for evaluation of SRA and quantifiable measurement scheme to evaluate quality of the SRA. We foresee that RADeF can facilitate software architects and researchers during...... of software systems need customized and systematic SRA design and evaluation methods. In this paper, we present a software Reference Architecture Design process Framework (RADeF) that can be used for analysis, design and evaluation of the SRA for provisioning of Tools as a Service as part of a cloud......Software Reference Architecture (SRA), which is a generic architecture solution for a specific type of software systems, provides foundation for the design of concrete architectures in terms of architecture design guidelines and architecture elements. The complexity and size of certain types...

  14. The Reification of Patterns in the Design of Description-Driven Systems

    CERN Document Server

    Le Goff, J M; Kovács, Z; McClatchey, R

    2001-01-01

    To address the issues of reusability and evolvability in designing self- describing systems, this paper proposes a pattern-based, object-oriented, description-driven system architecture. The proposed architecture embodies four pillars - first, the adoption of a multi-layered meta-modeling architecture and reflective meta-level architecture, second, the identification of four data modeling relationships that must be made explicit such that they can be examined and modified dynamically, third, the identification of five design patterns which have emerged from practice and have proved essential in providing reusable building blocks for data management, and fourth, the encoding of the structural properties of the five design patterns by means of one pattern, the Graph pattern. The CRISTAL research project served as the basis onto which the pattern-based meta-object approach has been applied. The proposed architecture allows the realization of reusability and adaptability, and is fundamental in the specification o...

  15. Lexical references to sensory modalities in verbal descriptions of people and objects by congenitally blind, late blind and sighted adults

    National Research Council Canada - National Science Library

    Chauvey, Valérie; Hatwell, Yvette; Verine, Bertrand; Kaminski, Gwenael; Gentaz, Edouard

    2012-01-01

    ...'), references to auditory and tactile attributes are scarcer. However, this statement may be challenged by current theories claiming that cognition is linked to the perceptions and actions from which it...

  16. Design Reference Missions (DRM): Integrated ODM 'Air-Taxi' Mission Features

    Science.gov (United States)

    Kloesel, Kurt; Starr, Ginn; Saltzman, John A.

    2017-01-01

    Design Reference Missions (DRM): Integrated ODM Air-Taxi Mission Features, Hybrid Electric Integrated System Testbed (HEIST) flight control. Structural Health, Energy Storage, Electric Components, Loss of Control, Degraded Systems, System Health, Real-Time IO Operator Geo-Fencing, Regional Noise Abatement and Trusted Autonomy Inter-operability.

  17. Designs of precoding for LTE TDD using cell specific reference signals

    DEFF Research Database (Denmark)

    Sun, Fan; Lu, Lu; Sørensen, Troels Bundgaard

    2010-01-01

    We design non-codebook-based Multiple-Input Multiple-Output (MIMO) precoding schemes using multiple cell-specific reference signals patterns for the time division duplex (TDD) mode of LTE, where channel reciprocity can be exploited. Previously proposed non-codebookbased precoding schemes typically...

  18. Los Alamos Controlled Air Incinerator for radioactive waste. Volume II. Engineering design reference manual

    Energy Technology Data Exchange (ETDEWEB)

    Koenig, R.A.; Draper, W.E.; Newmyer, J.M.; Warner, C.L.

    1982-10-01

    This two-volume report is a detailed design and operating documentation of the Los Alamos National Laboratory Controlled Air Incinerator (CAI) and is an aid to technology transfer to other Department of Energy contractor sites and the commercial sector. Volume I describes the CAI process, equipment, and performance, and it recommends modifications based on Los Alamos experience. It provides the necessary information for conceptual design and feasibility studies. Volume II provides descriptive engineering information such as drawings, specifications, calculations, and costs. It aids duplication of the process at other facilities.

  19. Reference design and operations for deep borehole disposal of high-level radioactive waste.

    Energy Technology Data Exchange (ETDEWEB)

    Herrick, Courtney Grant; Brady, Patrick Vane; Pye, Steven; Arnold, Bill Walter; Finger, John Travis; Bauer, Stephen J.

    2011-10-01

    A reference design and operational procedures for the disposal of high-level radioactive waste in deep boreholes have been developed and documented. The design and operations are feasible with currently available technology and meet existing safety and anticipated regulatory requirements. Objectives of the reference design include providing a baseline for more detailed technical analyses of system performance and serving as a basis for comparing design alternatives. Numerous factors suggest that deep borehole disposal of high-level radioactive waste is inherently safe. Several lines of evidence indicate that groundwater at depths of several kilometers in continental crystalline basement rocks has long residence times and low velocity. High salinity fluids have limited potential for vertical flow because of density stratification and prevent colloidal transport of radionuclides. Geochemically reducing conditions in the deep subsurface limit the solubility and enhance the retardation of key radionuclides. A non-technical advantage that the deep borehole concept may offer over a repository concept is that of facilitating incremental construction and loading at multiple perhaps regional locations. The disposal borehole would be drilled to a depth of 5,000 m using a telescoping design and would be logged and tested prior to waste emplacement. Waste canisters would be constructed of carbon steel, sealed by welds, and connected into canister strings with high-strength connections. Waste canister strings of about 200 m length would be emplaced in the lower 2,000 m of the fully cased borehole and be separated by bridge and cement plugs. Sealing of the upper part of the borehole would be done with a series of compacted bentonite seals, cement plugs, cement seals, cement plus crushed rock backfill, and bridge plugs. Elements of the reference design meet technical requirements defined in the study. Testing and operational safety assurance requirements are also defined. Overall

  20. Cold Vacuum Dryer (CVD) Facility Fire Protection System Design Description (SYS 24)

    Energy Technology Data Exchange (ETDEWEB)

    SINGH, G.

    2000-10-17

    This system design description (SDD) addresses the Cold Vacuum Drying (CVD) Facility fire protection system (FPS). The primary features of the FPS for the CVD are a fire alarm and detection system, automatic sprinklers, and fire hydrants. The FPS also includes fire extinguishers located throughout the facility and fire hydrants to assist in manual firefighting efforts. In addition, a fire barrier separates the operations support (administrative) area from the process bays and process bay support areas. Administrative controls to limit combustible materials have been established and are a part of the overall fire protection program. The FPS is augmented by assistance from the Hanford Fire Department (HED) and by interface systems including service water, electrical power, drains, instrumentation and controls. This SDD, when used in conjunction with the other elements of the definitive design package, provides a complete picture of the FPS for the CVD Facility.

  1. [Simulation on design-based and model-based methods in descriptive analysis of complex samples].

    Science.gov (United States)

    Li, Yichong; Yu, Shicheng; Zhao, Yinjun; Jiang, Yong; Wang, Limin; Zhang, Mei; Jiang, Wei; Bao, Heling; Zhou, Maigeng; Jiang, Bo

    2015-01-01

    To compare design-based and model-based methods in descriptive analysis of complex sample. A total of 1 000 samples were selected and a multistage random sampling design was used in the analysis of the 2010 China chronic disease and risk factors surveillance. For each simulated sample, cases with probability proportional age were randomly deleted so that sample age structure was deviated systematically from that of the target population. Mean systolic blood pressure (SBP) and prevalence of raised blood pressure, as well as their 95% confidence intervals (95%CI) were determined using design-based and model-based methods (routine method and multi-level model). For estimators generated from those 3 methods, mean squared error(MSE) was computed to evaluate their validity. To compare performance of statistical inference of these methods, the probability of 95%CI covering the true parameter(mean SBP and raised blood pressure prevalence of the population) was used. MSE of mean estimator for routine method, design-based analysis and multilevel model was 6.41, 1.38, and 5.86, respectively; and the probability of 95%CI covering the true parameter was 24.7%, 97.5% and 84.3%, respectively. The routine method and multi-level model probably led to an increased probability of type I error in statistical inference. MSE of prevalence estimator was 4.80 for design-based method, which was far lower than those for routine method (20.9) and multilevel model (17.2). Probability of 95%CI covering the true prevalence for routine method was only 29.4%, and 86.4% for multilevel model, both of which were lower than that for design-based method (97.3%). Compared to routine method and multi-level model, design-based method had the best performance both in point estimation and confidence interval construction. Design-based method should be the first choice when doing statistical description of complex samples with a systematically biased sample structure.

  2. Progress of the ITER NBI acceleration grid power supply reference design

    Energy Technology Data Exchange (ETDEWEB)

    Toigo, Vanni [Consorzio RFX, Associazione EURATOM-ENEA sulla Fusione, Corso Stati Uniti 4, I-35127 Padova (Italy); Zanotto, Loris, E-mail: loris.zanotto@igi.cnr.it [Consorzio RFX, Associazione EURATOM-ENEA sulla Fusione, Corso Stati Uniti 4, I-35127 Padova (Italy); Bigi, Marco [Consorzio RFX, Associazione EURATOM-ENEA sulla Fusione, Corso Stati Uniti 4, I-35127 Padova (Italy); Decamps, Hans [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France); Ferro, Alberto; Gaio, Elena [Consorzio RFX, Associazione EURATOM-ENEA sulla Fusione, Corso Stati Uniti 4, I-35127 Padova (Italy); Gutiérrez, Daniel [Fusion For Energy, C/Josep Pla 2, 08019 Barcelona (Spain); Tsuchida, Kazuki; Watanabe, Kazuhiro [Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki-ken 311-0193 (Japan)

    2013-10-15

    Highlights: ► This paper reports the progress in the reference design of the Acceleration Grid Power Supply (AGPS) of the ITER Neutral Beam Injector (NBI) ► A critical revision of the main design choices is presented in light of the definition of some key interface parameters between the two AGPS subsystems. ► The verification of the fulfillment of the requirements in any operational conditions is reported and discussed. -- Abstract: This paper reports the progress in the reference design of the Acceleration Grid Power Supply (AGPS) of the ITER Neutral Beam Injector (NBI). The design of the AGPS is very challenging, as it shall be rated to provide about 55 MW at 1 MV dc in quasi steady-state conditions; moreover, the procurement of the system is shared between the European Domestic Agency (F4E) and the Japanese Domestic Agency (JADA), resulting in additional design complication due to the need of a common definition of the interface parameters. A critical revision of the main design choices is presented also in light of the definition of some key interface parameters between the two AGPS subsystems. Moreover, the verification of the fulfillment of the requirements in any operational conditions taking into account the tolerance of the different parameters is also reported and discussed.

  3. Description of research design of articles published in four Brazilian physical therapy journals.

    Science.gov (United States)

    Saragiotto, Bruno T; Costa, Lucíola C M; Oliveira, Ronaldo F; Lopes, Alexandre D; Moseley, Anne M; Costa, Leonardo O P

    2014-01-01

    While the research design of articles published in medical journals and in some physical therapy journals has already been evaluated, this has not been investigated in Brazilian physical therapy journals. Objective : To describe the research design used in all articles published in Brazilian scientific journals that are freely available, have high Qualis rankings, and are relevant to physical therapy over a 7-year period. We extracted the bibliometric data, research design, research type (human or animal), and clinical area for all articles published. The articles were grouped into their level of evidence, and descriptive analyses were performed. We calculated the frequency, proportions of articles, and 95% confidence interval of these proportions with each research design in each journal. We cross-tabulated the clinical areas with research designs (expressed as number and percentages). A total of 1,458 articles from four Brazilian journals were found: Revista Brasileira de Fisioterapia, Revista Fisioterapia em Movimento, Revista Fisioterapia e Pesquisa, and Revista Acta Fisiátrica. The majority of articles were classified as level II of evidence (60%), followed by level III (29%) and level I (10%). The most prevalent research designs were cross-sectional studies (38%), single-case or case-series studies, and narrative reviews. Most articles reported human research and were in the musculoskeletal, neurologic, and cardiothoracic areas. Most of the research published in Brazilian physical therapy journals used levels II and III of evidence. Increasing the publication rate of systematic reviews and randomized controlled trials would provide more high-quality evidence to guide evidence-based physical therapy practice.

  4. Description of research design of articles published in four Brazilian physical therapy journals

    Directory of Open Access Journals (Sweden)

    Bruno T. Saragiotto

    2014-03-01

    Full Text Available Background : While the research design of articles published in medical journals and in some physical therapy journals has already been evaluated, this has not been investigated in Brazilian physical therapy journals. Objective : To describe the research design used in all articles published in Brazilian scientific journals that are freely available, have high Qualis rankings, and are relevant to physical therapy over a 7-year period. Method : We extracted the bibliometric data, research design, research type (human or animal, and clinical area for all articles published. The articles were grouped into their level of evidence, and descriptive analyses were performed. We calculated the frequency, proportions of articles, and 95% confidence interval of these proportions with each research design in each journal. We cross-tabulated the clinical areas with research designs (expressed as number and percentages. Results : A total of 1,458 articles from four Brazilian journals were found: Revista Brasileira de Fisioterapia, Revista Fisioterapia em Movimento, Revista Fisioterapia e Pesquisa, and Revista Acta Fisiátrica. The majority of articles were classified as level II of evidence (60%, followed by level III (29% and level I (10%. The most prevalent research designs were cross-sectional studies (38%, single-case or case-series studies, and narrative reviews. Most articles reported human research and were in the musculoskeletal, neurologic, and cardiothoracic areas. Conclusions : Most of the research published in Brazilian physical therapy journals used levels II and III of evidence. Increasing the publication rate of systematic reviews and randomized controlled trials would provide more high-quality evidence to guide evidence-based physical therapy practice.

  5. A reference model for model-based design of critical infrastructure protection systems

    Science.gov (United States)

    Shin, Young Don; Park, Cheol Young; Lee, Jae-Chon

    2015-05-01

    Today's war field environment is getting versatile as the activities of unconventional wars such as terrorist attacks and cyber-attacks have noticeably increased lately. The damage caused by such unconventional wars has also turned out to be serious particularly if targets are critical infrastructures that are constructed in support of banking and finance, transportation, power, information and communication, government, and so on. The critical infrastructures are usually interconnected to each other and thus are very vulnerable to attack. As such, to ensure the security of critical infrastructures is very important and thus the concept of critical infrastructure protection (CIP) has come. The program to realize the CIP at national level becomes the form of statute in each country. On the other hand, it is also needed to protect each individual critical infrastructure. The objective of this paper is to study on an effort to do so, which can be called the CIP system (CIPS). There could be a variety of ways to design CIPS's. Instead of considering the design of each individual CIPS, a reference model-based approach is taken in this paper. The reference model represents the design of all the CIPS's that have many design elements in common. In addition, the development of the reference model is also carried out using a variety of model diagrams. The modeling language used therein is the systems modeling language (SysML), which was developed and is managed by Object Management Group (OMG) and a de facto standard. Using SysML, the structure and operational concept of the reference model are designed to fulfil the goal of CIPS's, resulting in the block definition and activity diagrams. As a case study, the operational scenario of the nuclear power plant while being attacked by terrorists is studied using the reference model. The effectiveness of the results is also analyzed using multiple analysis models. It is thus expected that the approach taken here has some merits

  6. A Substractive Clustering Based Fuzzy Hybrid Reference Control Design for Transient Response Improvement of PID Controller

    Directory of Open Access Journals (Sweden)

    Endra Joelianto

    2009-11-01

    Full Text Available The well known PID controller has inherent limitations in fulfilling simultaneously the conflicting control design objectives. Parameters of the tuned PID controller should trade off the requirement of tracking set-point performances, disturbance rejection and stability robustness. Combination of hybrid reference control (HRC with PID controller results in the transient response performances can be independently achieved without deteriorating the disturbance rejection properties and the stability robustness requirement. This paper proposes a fuzzy based HRC where the membership functions of the fuzzy logic system are obtained by using a substractive clustering technique. The proposed method guarantees the transient response performances satisfaction while preserving the stability robustness of the closed loop system controlled by the PID controller with effective and systematic procedures in designing the fuzzy hybrid reference control system.

  7. Quasichemical theory and the description of associating fluids relative to a reference: Multiple bonding of a single site solute

    Science.gov (United States)

    Bansal, Artee; Chapman, Walter G.; Asthagiri, D.

    2017-09-01

    We derive an expression for the chemical potential of an associating solute in a solvent relative to the value in a reference fluid using the quasichemical organization of the potential distribution theorem. The fraction of times the solute is not associated with the solvent, the monomer fraction, is expressed in terms of (a) the statistics of occupancy of the solvent around the solute in the reference fluid and (b) the Widom factors that arise because of turning on solute-solvent association. Assuming pair-additivity, we expand the Widom factor into a product of Mayer f-functions and the resulting expression is rearranged to reveal a form of the monomer fraction that is analogous to that used within the statistical associating fluid theory (SAFT). The present formulation avoids all graph-theoretic arguments and provides a fresh, more intuitive, perspective on Wertheim's theory and SAFT. Importantly, multi-body effects are transparently incorporated into the very foundations of the theory. We illustrate the generality of the present approach by considering examples of multiple solvent association to a colloid solute with bonding domains that range from a small patch on the sphere to a Janus particle to a solute whose entire surface is available for association.

  8. Quasichemical theory and the description of associating fluids relative to a reference: Multiple bonding of a single site solute.

    Science.gov (United States)

    Bansal, Artee; Chapman, Walter G; Asthagiri, D

    2017-09-28

    We derive an expression for the chemical potential of an associating solute in a solvent relative to the value in a reference fluid using the quasichemical organization of the potential distribution theorem. The fraction of times the solute is not associated with the solvent, the monomer fraction, is expressed in terms of (a) the statistics of occupancy of the solvent around the solute in the reference fluid and (b) the Widom factors that arise because of turning on solute-solvent association. Assuming pair-additivity, we expand the Widom factor into a product of Mayer f-functions and the resulting expression is rearranged to reveal a form of the monomer fraction that is analogous to that used within the statistical associating fluid theory (SAFT). The present formulation avoids all graph-theoretic arguments and provides a fresh, more intuitive, perspective on Wertheim's theory and SAFT. Importantly, multi-body effects are transparently incorporated into the very foundations of the theory. We illustrate the generality of the present approach by considering examples of multiple solvent association to a colloid solute with bonding domains that range from a small patch on the sphere to a Janus particle to a solute whose entire surface is available for association.

  9. Behavioral emergency in the elderly: a descriptive study of patients referred to an Aggression Response Team in an acute hospital

    Directory of Open Access Journals (Sweden)

    Simpkins D

    2016-10-01

    Full Text Available Daniel Simpkins,1 Carmelle Peisah,2,3 Irene Boyatzis1 1Division of Rehabilitation and Aged Care, Hornsby Ku-ring-gai Hospital, 2School of Psychiatry, University of New South Wales, 3Discipline of Psychiatry, University of Sydney, Sydney, NSW, Australia Aim: The management of severely agitated elderly patients is not easy, and limited guidelines are available to assist practitioners. At a Sydney hospital, an Aggression Response Team (ART comprising clinical and security staff can be alerted when a staff member has safety concerns. Our aims were to describe the patient population referred for ART calls, reasons for and interventions during ART calls, and complications following them.Methods: Patients 65 years and older referred for ART calls in the emergency department or wards during 2014 were identified using the Incident Information Management System database and medical records were reviewed. Demographic and clinical data were collected. Results: Of 43 elderly patients with ART calls, 30 had repeat ART calls. Thirty-one patients (72% had underlying dementia, and 22 (51% were agitated at the time of admission. The main reasons for ART calls were wandering and physical aggression. Pharmacological sedation was used in 88% of the ART calls, with a range of psychotropics, doses, and routes of administration, including intravenous (19% and, most commonly, midazolam (53%. Complications were documented in 14% of cases where sedation was used. Conclusion: We observed a high frequency of pharmacological sedation among the severely agitated elderly, with significant variance in the choice and dose of sedation and a high rate of complications arising from sedation, which may be an underestimate given the lack of post-sedation monitoring. We recommend the development of guidelines on the management of behavioral emergency in the elderly patients, including de-escalation strategies and standardized psychotropic guidelines. Keywords: aged, aggression

  10. Preliminary Comparative Evaluation Study on Reference Design of GEN-IV SFR

    Energy Technology Data Exchange (ETDEWEB)

    Sim, Yoon Sub; Kim, Yeong Il; Hong, Ser Gi (and others)

    2005-11-15

    A fast reactor has a good transmutation capability and it enables breeding of fuel and use of a closed fuel cycle. By these characteristics of a fast reactor, the limited uranium resources of the world can be much more effectively utilized and the nuclear wastes of a high level of radioactivity and toxicity from the current nuclear power reactors of LWRs and HWRs can be drastically reduced in its volume and the management of the wastes can be easily treated. Also electricity can be generated more effectively since a fast reactor has the feature of high operation temperature. These features of a fast reactor makes it inevitable on a long term basis to construct fast reactors in Korea. The domestic fast reactor technology level, however, is at the level of coming out of a beginning stage and needs utilization of international expertise. Recently an international cooperation program called GIF has been formulated and our KALIMER was selected as one of the two reference designs for the international joint R and D works with JSFR of Japan. In the current frame of the GIF program, the two selected reference designs are supposed to be evaluated against each other in future and one design is to be finally selected. To make the international cooperation program directed more useful to our fast reactor technology development, it is required to strengthen the competitiveness of KALIMER so that it can be selected. To meet the necessity, a study was made in this research for pre-evaluation of the GIF reference designs and setting up plans for development of designs and technology that will enhance the competitiveness of KALIMER.

  11. FLOATING ELBOW IN CHILDREN: A DESCRIPTIVE STUDY OF 31 CASES ATTENDED IN A REFERENCE CENTER FOR PEDIATRIC TRAUMA

    Science.gov (United States)

    Malheiros, Dorotea Starling; Bárbara, Gustavo Henrique Silva; Mafalda, Leandro Gonçalves; Madureira, João Lopo; Braga, Gilberto Ferreira; Terra, Dalton Lopes

    2015-01-01

    Objective: To conduct a descriptive analysis on 31 cases of children with floating elbow who were attended at our clinic between 1994 and 2009, and to review the literature relating to this topic. Methods: Data were obtained through examining the medical records. The following variables were used: age, gender, side, mechanism, type of fracture, classification, treatment and complications. Results: Twenty-four patients (77.4%) were male and seven (22.6%) were female. The mean age was 8.5 (± 3.2) years, ranging from one to 14 years. The left side was predominantly affected (67.7%). The commonest injury mechanism was a fall from a height (74.2%). All the supracondylar fractures were Gartland type III. Distal radius fractures alone, of Salter-Harris type II, were diagnosed in 22 patients (71%). Open fractures occurred in 22 cases (71%). Closed reduction and application of a plaster cast for a closed fracture of the distal radius was performed in two patients (6.45%). Simultaneous conservative treatment for two fractures was not used. Sixteen supracondylar fractures (54.8%) were fixed using crossed wires, at 90° to each other, and in 14 cases (45.16%), an intramedullary wire was used together with another wire introduced through the lateral epicondyle at 45°. The following complications were observed: deformed consolidation (10%), nerve injuries (6%), compartment syndrome (3%) and pin path infection (16%). Conclusions: This is an uncommon injury that in most cases results from high-energy trauma. Surgical treatment for both fractures is recommended by most authors. Ulnar nerve injuries were correlated with the fixation method, but no neurological injuries were triggered by the initial trauma. PMID:27027045

  12. Detailed conceptual designs and economic analyses of a reference Photovoltaic Central Power Station

    Science.gov (United States)

    Hughes, D. J.; Heller, B. W.; Stephenson, J. E.

    Detailed conceptual designs and economic analyses of a reference 100MWe Photovoltaic Central Power Station (PV CPS) have been completed. Both flat plate dendritic WEB and point focus fresnel concentrator (100X concentration) arrays were used to develop two individual central station reference designs. Design requirements, detailed drawings and system, subsystem and component specifications form the basis for a plant construction cost estimate. The flat plate array PV CPS costs range from $179M to $483M (1982 U.S. Dollars) for array costs ranging from $1/Wp to $3.50/Wp and power conditioning unit (PCU) costs from $.05/Wp to $.50/Wp. Similar costs for the concentrator PV CPS range from $201M to $505M, respectively. Using representative utility financial parameters, in-house economic models, and a plant performance estimate, levelized busbar energy costs (BBEC) are derived for both flat plate and concentrator designs. BBEC range from $.15/kWh to $.41/kWh for the flat plate PV CPS from $.15/kWh to $.37/kWh for the concentrator PV CPS.

  13. A Description of Reference Ranges for Organic Acids in Urine Samples from A Pediatric Population in Iran.

    Science.gov (United States)

    Keyfi, Fatemeh; Lukacs, Zoltan; Varasteh, Abdolreza

    2017-10-01

    Organic acids refer to a family of compounds that are intermediates in a variety of metabolic pathways. Many organic acids are present in urine from clinically normal individuals. Elevated levels of urine organic acids cause to the organic acidurias, disorders in which some metabolic pathways in organic acid metabolism are blocked. The present work identified major and minor urinary acidic metabolites in normal subjects, and their quantitative ranges in a pediatric population of Iran. Two hundred and fifty-one healthy subjects, including 132 males and 119 females, from 2 days to 15 years of age were enrolled. Urinary organic acids were extracted from urine with organic solvents and identified and quantified by gas chromatography-mass spectrometry. The results provide a foundation on which to check results for patients with potentially abnormal organic acidurias. By this method 98 organic acids were identified in a pediatric population of Iran. The present work identifies and quantifies major and minor urinary metabolites excreted by normal subjects. We also analyzed urine from 30 patients with organic acid metabolism abnormalities and compared the concentrations of specific organic acids with those from urines of normal individuals.

  14. A self-description data framework for Tokamak control system design

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Ming; Zhang, Jing [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, Wuhan 430074 (China); School of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China); Zheng, Wei, E-mail: zhengwei@hust.edu.cn [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, Wuhan 430074 (China); School of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China); Hu, Feiran; Zhuang, Ge [State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, Wuhan 430074 (China); School of Electrical and Electronic Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China)

    2015-10-15

    Highlights: • The SDD framework can be applied to different Tokamak devices. • We explain how configuration settings of control systems are described in SDD models, namely components and connections. • Evolving SDD models are stored in a dynamic schema database. • The SDD editor supports plug-and-play SDD models. - Abstract: A Tokamak device consists of numerous control systems, which need to be integrated. CODAC (Control, Data Access and Communication) system requires the configuration settings of these control systems to carry out the integration smoothly. SDD (Self-description data) is designed to describe the static configuration of control systems. ITER CODAC group has released an SDD software package for control system designers to manage the static configuration, but it is specific for ITER plant control systems. Following the idea of ITER SDD, we developed a flexible and scalable SDD framework to develop SDD software for J-TEXT and other sophisticated devices. The SDD framework describes the configuration settings of various control systems, including physical and logical elements and their relation information, in SDD models which are classified into Components and Connections. The framework is composed of three layers: the MongoDB database, an open-source, dynamic schema, NoSQL (Not Only SQL) database; the SDD service, which maps SDD models to MongoDB and handles the transaction and business logic; the SDD applications, which can be used to create and maintain SDD information, and generate various kinds of output using the stored SDD information.

  15. Enhanced Radar Imaging in Uncertain Environment: A Descriptive Experiment Design Regularization Approach

    Directory of Open Access Journals (Sweden)

    Yuriy Shkvarko

    2008-01-01

    Full Text Available A new robust technique for high-resolution reconstructive imaging is developed as required for enhanced remote sensing (RS with imaging array radar or/and synthetic aperture radar (SAR operating in an uncertain RS environment. The operational scenario uncertainties are associated with the unknown statistics of perturbations of the signal formation operator (SFO in turbulent medium, imperfect array calibration, finite dimensionality of measurements, uncontrolled antenna vibrations, and random carrier trajectory deviations in the case of SAR. We propose new descriptive experiment design regularization (DEDR approach to treat the uncertain radar image enhancement/reconstruction problems. The proposed DEDR incorporates into the minimum risk (MR nonparametric estimation strategy the experiment design-motivated operational constraints algorithmically coupled with the worst-case statistical performance (WCSP optimization-based regularization. The MR objective functional is constrained by the WCSP information, and the robust DEDR image reconstruction operator applicable to the scenarios with the low-rank uncertain estimated data correlation matrices is found. We report and discuss some simulation results related to enhancement of the uncertain SAR imagery indicative of the significantly increased performance efficiency gained with the developed approach.

  16. Overview of the Mission Design Reference Trajectory for NASA's Asteroid Redirect Robotic Mission

    Science.gov (United States)

    Mcguire, Melissa L.; Strange, Nathan J.; Burke, Laura M.; McCarty, Steven L.; Lantoine, Gregory B.; Qu, Min; Shen, Haijun; Smith, David A.; Vavrina, Matthew A.

    2017-01-01

    The National Aeronautics and Space Administration's (NASA's) recently cancelled Asteroid Redirect Mission was proposed to rendezvous with and characterize a 100 m plus class near-Earth asteroid and provide the capability to capture and retrieve a boulder off of the surface of the asteroid and bring the asteroidal material back to cislunar space. Leveraging the best of NASA's science, technology, and human exploration efforts, this mission was originally conceived to support observation campaigns, advanced solar electric propulsion, and NASA's Space Launch System heavy-lift rocket and Orion crew vehicle. The asteroid characterization and capture portion of ARM was referred to as the Asteroid Redirect Robotic Mission (ARRM) and was focused on the robotic capture and then redirection of an asteroidal boulder mass from the reference target, asteroid 2008 EV5, into an orbit near the Moon, referred to as a Near Rectilinear Halo Orbit where astronauts would visit and study it. The purpose of this paper is to document the final reference trajectory of ARRM and the challenges and unique methods employed in the trajectory design of the mission.

  17. A Basic Robotic Excavator (the Glenn Digger): Description, Design, and Initial Operation

    Science.gov (United States)

    Bauman, Steve; Newman, Paul; Izadnegahdar, Alain; Johnson, Kyle; Abel, Phillip

    2016-01-01

    This paper describes the design, commercial part selections, fabrication, assembly, installation, and initial operation of a two degree of freedom robotic excavator. Colloquially referred to as "the NASA Glenn Digger," it was designed specifically to be mounted onto, and to operate with, the then newly developed Centaur 2 robotic mobility base. The excavator, when mounted to Centaur 2, is designed to scoop loose regolith from the terrain, raise its loaded bucket up and dump the load into a hopper of at least a 1-m-height. The hopper represents the input to a machine that would process the raw material, such as to produce oxygen from lunar regolith as would be required for long-term lunar habitation. This equipment debuted at the annual Research and Technology Studies ("Desert RATS", Ref. 1) event held north of Flagstaff, Arizona, in September of 2010, when the Digger was successfully joined to Centaur 2 and the shoveling articulation was demonstrated. During 2011, the hardware was modified for added strength, strain gauges were added to measure loads, and the controls were improved in preparation for the 2011 Desert RATS event, where additional "field operations" experience was gained.

  18. JOKARUS - design of a compact optical iodine frequency reference for a sounding rocket mission

    Energy Technology Data Exchange (ETDEWEB)

    Schkolnik, Vladimir; Doeringshoff, Klaus; Gutsch, Franz Balthasar; Krutzik, Markus [Humboldt-Universitaet zu Berlin, Berlin (Germany); Oswald, Markus [Universitaet Bremen, Zentrum fuer angewandte Raumfahrttechnologie und Mikrogravitation (ZARM), Bremen (Germany); Schuldt, Thilo [Institut fuer Raumfahrtsysteme, Deutsches Zentrum fuer Luft- und Raumfahrt (DLR), Bremen (Germany); Braxmaier, Claus [Universitaet Bremen, Zentrum fuer angewandte Raumfahrttechnologie und Mikrogravitation (ZARM), Bremen (Germany); Institut fuer Raumfahrtsysteme, Deutsches Zentrum fuer Luft- und Raumfahrt (DLR), Bremen (Germany); Lezius, Matthias; Holzwarth, Ronald [Menlo Systems GmbH, Martinsried (Germany); Kuerbis, Christian; Bawamia, Ahmad [Leibniz-Institut fuer Hoechstfrequenztechnik, Ferdinand-Braun-Institut, Berlin (Germany); Peters, Achim [Humboldt-Universitaet zu Berlin, Berlin (Germany); Leibniz-Institut fuer Hoechstfrequenztechnik, Ferdinand-Braun-Institut, Berlin (Germany)

    2017-12-15

    We present the design of a compact absolute optical frequency reference for space applications based on hyperfine transitions in molecular iodine with a targeted fractional frequency instability of better than 3 x 10{sup -14} after 1 s. It is based on a micro-integrated extended cavity diode laser with integrated optical amplifier, fiber pigtailed second harmonic generation wave-guide modules, and a quasi-monolithic spectroscopy setup with operating electronics. The instrument described here is scheduled for launch end of 2017 aboard the TEXUS 54 sounding rocket as an important qualification step towards space application of iodine frequency references and related technologies. The payload will operate autonomously and its optical frequency will be compared to an optical frequency comb during its space flight. (orig.)

  19. College students' perceptions of sexual orientation and gender given job descriptions and titles for interior decoration, interior design, and architecture.

    Science.gov (United States)

    Wood-Nartker, B Jeanneane; Sepanski, Jungsywan; McCrady, Joe; Gligor, Andreea

    2007-06-01

    To examine perceptions of design professionals, this study was designed to examine possible gender-bias based on job title and description and whether there is a relationship between the two perceptions. A respondent's sex was significantly related to perceptions of a design professional's sex. Both respondents' sex and the perceived sex of the design professional had significant effects on the perceived sexual orientation of the design professionals. Furthermore, the results also indicated that if the design professional was perceived to be male, there was a higher tendency that he would be perceived as homosexual, especially by a male respondent.

  20. Parcels and Land Ownership, Parcel boundaries for Johnson County Kansas based off of legal description. Used to show spatial reference to parcel boundaries of Johnson County Kansas., Published in 2007, Johnson County Government.

    Data.gov (United States)

    NSGIC Local Govt | GIS Inventory — Parcels and Land Ownership dataset current as of 2007. Parcel boundaries for Johnson County Kansas based off of legal description. Used to show spatial reference to...

  1. Requirements and Design Reference Mission for the WFIRST-AFTA Coronagraph Instrument

    Science.gov (United States)

    Demers, Richard T.; Dekens, Frank; Calvet, Rob; Chang, Zensheu; Effinger, Robert; Ek, Eric; Hovland, Larry; Jones, Laura; Loc, Anthony; Nemati, Bijan; hide

    2015-01-01

    The WFIRST-AFTA coronagraph instrument take s advantage of AFTA s 2.4 -meter aperture to provide novel exoplanet imaging science at approximately the same instrument cost as an Explorer mission. The AFTA coronagraph also matures direct imaging technologies to high TRL for an Exo-Earth Imager in the next decade. The coronagraph Design Reference Mission (DRM) optical design is based on the highly successful High Contrast Imaging Testbed (HCIT), with modifications to accommodate the AFTA telescope design, service-ability, volume constraints, and the addition of an Integral Field Spectrograph (IFS). In order to optimally satisfy the three science objectives of planet imaging, planet spectral characterization and dust debris imaging, the coronagraph is designed to operate in two different modes : Hybrid Lyot Coronagraph or Shaped Pupil Coronagraph. Active mechanisms change pupil masks, focal plane masks, yot masks, and bandpass filters to shift between modes. A single optical beam train can thus operate alternatively as two different coronagraph architecture s. Structural Thermal Optical Performance (STOP) analysis predict s the instrument contrast with the Low Order Wave Front Control loop closed. The STOP analysis was also used to verify that the optical/structural/thermal design provides the extreme stability required for planet characterization in the presence of thermal disturbances expected in a typical observing scenario. This paper describes the instrument design and the flow down from science requirements to high level engineering requirements.

  2. DAKOTA, a multilevel parallel object-oriented framework for design optimization, parameter estimation, uncertainty quantification, and sensitivity analysis:version 4.0 reference manual

    Energy Technology Data Exchange (ETDEWEB)

    Griffin, Joshua D. (Sandai National Labs, Livermore, CA); Eldred, Michael Scott; Martinez-Canales, Monica L. (Sandai National Labs, Livermore, CA); Watson, Jean-Paul; Kolda, Tamara Gibson (Sandai National Labs, Livermore, CA); Adams, Brian M.; Swiler, Laura Painton; Williams, Pamela J. (Sandai National Labs, Livermore, CA); Hough, Patricia Diane (Sandai National Labs, Livermore, CA); Gay, David M.; Dunlavy, Daniel M.; Eddy, John P.; Hart, William Eugene; Guinta, Anthony A.; Brown, Shannon L.

    2006-10-01

    The DAKOTA (Design Analysis Kit for Optimization and Terascale Applications) toolkit provides a flexible and extensible interface between simulation codes and iterative analysis methods. DAKOTA contains algorithms for optimization with gradient and nongradient-based methods; uncertainty quantification with sampling, reliability, and stochastic finite element methods; parameter estimation with nonlinear least squares methods; and sensitivity/variance analysis with design of experiments and parameter study methods. These capabilities may be used on their own or as components within advanced strategies such as surrogate-based optimization, mixed integer nonlinear programming, or optimization under uncertainty. By employing object-oriented design to implement abstractions of the key components required for iterative systems analyses, the DAKOTA toolkit provides a flexible and extensible problem-solving environment for design and performance analysis of computational models on high performance computers. This report serves as a reference manual for the commands specification for the DAKOTA software, providing input overviews, option descriptions, and example specifications.

  3. DAKOTA : a multilevel parallel object-oriented framework for design optimization, parameter estimation, uncertainty quantification, and sensitivity analysis. Version 5.0, user's reference manual.

    Energy Technology Data Exchange (ETDEWEB)

    Eldred, Michael Scott; Dalbey, Keith R.; Bohnhoff, William J.; Adams, Brian M.; Swiler, Laura Painton; Hough, Patricia Diane (Sandia National Laboratories, Livermore, CA); Gay, David M.; Eddy, John P.; Haskell, Karen H.

    2010-05-01

    The DAKOTA (Design Analysis Kit for Optimization and Terascale Applications) toolkit provides a flexible and extensible interface between simulation codes and iterative analysis methods. DAKOTA contains algorithms for optimization with gradient and nongradient-based methods; uncertainty quantification with sampling, reliability, and stochastic finite element methods; parameter estimation with nonlinear least squares methods; and sensitivity/variance analysis with design of experiments and parameter study methods. These capabilities may be used on their own or as components within advanced strategies such as surrogate-based optimization, mixed integer nonlinear programming, or optimization under uncertainty. By employing object-oriented design to implement abstractions of the key components required for iterative systems analyses, the DAKOTA toolkit provides a flexible and extensible problem-solving environment for design and performance analysis of computational models on high performance computers. This report serves as a reference manual for the commands specification for the DAKOTA software, providing input overviews, option descriptions, and example specifications.

  4. Reference Function Based Spatiotemporal Fuzzy Logic Control Design Using Support Vector Regression Learning

    Directory of Open Access Journals (Sweden)

    Xian-Xia Zhang

    2013-01-01

    Full Text Available This paper presents a reference function based 3D FLC design methodology using support vector regression (SVR learning. The concept of reference function is introduced to 3D FLC for the generation of 3D membership functions (MF, which enhance the capability of the 3D FLC to cope with more kinds of MFs. The nonlinear mathematical expression of the reference function based 3D FLC is derived, and spatial fuzzy basis functions are defined. Via relating spatial fuzzy basis functions of a 3D FLC to kernel functions of an SVR, an equivalence relationship between a 3D FLC and an SVR is established. Therefore, a 3D FLC can be constructed using the learned results of an SVR. Furthermore, the universal approximation capability of the proposed 3D fuzzy system is proven in terms of the finite covering theorem. Finally, the proposed method is applied to a catalytic packed-bed reactor and simulation results have verified its effectiveness.

  5. Solar Pilot Plant, Phase I. Preliminary design report. Volume II. System description and system analysis. CDRL item 2

    Energy Technology Data Exchange (ETDEWEB)

    None

    1977-05-01

    Honeywell conducted a parametric analysis of the 10-MW(e) solar pilot plant requirements and expected performance and established an optimum system design. The main analytical simulation tools were the optical (ray trace) and the dynamic simulation models. These are described in detail in Books 2 and 3 of this volume under separate cover. In making design decisions, available performance and cost data were used to provide a design reflecting the overall requirements and economics of a commercial-scale plant. This volume contains a description of this analysis/design process and resultant system/subsystem design and performance.

  6. Using Reference Architectures for Design and Evaluation of Web of Things Systems

    DEFF Research Database (Denmark)

    Chauhan, Muhammad Aufeef; Babar, Muhammad Ali

    2017-01-01

    Web of Things (WoT) provides abstraction that simplifies the creation of Internet of Things (IoT) systems. IoT systems are designed to support a number of ubiquitous devices and management subsystems. The devices and subsystems can be a part of safety critical op- erations as well as smart...... management of multiple actuators that control the smart home devices. The devices and subsystems need to comply to standardized business and quality requirements of a specific IoT domain. Designing subsystems and actuators for the individual devices as independent software can result in lack...... of standardization, which can neg- atively impact the overall quality of a WoT system. Standardisation of the IoT applications and subsystems constituting a WoT system can be facilitated by providing a standardisation at the architecture level. As using Reference Architectures (RA) is a well established ap- proach...

  7. 30 CFR 250.413 - What must my description of well drilling design criteria address?

    Science.gov (United States)

    2010-07-01

    ..., DEPARTMENT OF THE INTERIOR OFFSHORE OIL AND GAS AND SULPHUR OPERATIONS IN THE OUTER CONTINENTAL SHELF Oil and Gas Drilling Operations Applying for A Permit to Drill § 250.413 What must my description of well... 30 Mineral Resources 2 2010-07-01 2010-07-01 false What must my description of well drilling...

  8. Usability Testing Analysis on The Bana Game as Education Game Design References on Junior High School

    Directory of Open Access Journals (Sweden)

    F. Adnan

    2017-04-01

    Full Text Available Learning media is one of the important elements in the learning process. Technological development support makes learning media more varied. The approach of using digital technology as a learning media has a better and more effective impact than other approaches. In order to increase the students’ learning interest, it requires the support of an interesting learning media. The use of gaming applications as learning media can improve learning outcomes. The benefits of using the maximum application cannot be separated from the determination of application design. The Bana game aims to increase the ability of critical thinking of the junior high school students. The usability-testing analysis on the Bana game application is used in order to get the design reference as an educational game development. The game is used as an object of the analysis because it has the same characteristics and goals with the game application to be developed. Usability Testing is a method used to measure the ease of use of an application by users. The Usability Testing consists of learnability, efficiency, memorability, errors, and satisfaction. The results of the analysis obtained will be used as a reference for educational game applications that will be developed.

  9. Implementing a Description Grammar Interpreter : A Notation for Descriptions and Description Rules

    NARCIS (Netherlands)

    Stouffs, R.M.F.

    2015-01-01

    Description grammars represent a formalism for generating verbal descriptions of designs, used in conjunction with shape grammars. A description grammar constitutes a set of description rules that define a language of descriptions. A description grammar interpreter implements the mechanisms to

  10. Interchangeability among reference insulin analogues and their biosimilars: regulatory framework, study design and clinical implications.

    Science.gov (United States)

    Dowlat, H A; Kuhlmann, M K; Khatami, H; Ampudia-Blasco, F J

    2016-08-01

    Biosimilars are regulated differently from small-molecule generic, chemically derived medicines. The complexity of biological products means that small changes in manufacturing or formulation may result in changes in efficacy and safety of the final product. In the face of this complexity, the regulatory landscape for biosimilars continues to evolve, and global harmonization regarding requirements is currently lacking. It is essential that clinicians and patients are reassured that biosimilars are equally safe and effective as their reference product, and this is particularly important when interchangeability, defined as 'changing one medicine for another one which is expected to achieve the same clinical effect in a given clinical setting in any one patient', is considered. Although the automatic substitution (i.e. substitution without input from the prescribing healthcare provider) of biosimilars for reference products is currently not permitted by the majority of countries, this may change in the future. In order to demonstrate interchangeability between reference products and a biosimilar, more stringent and specific studies of the safety and efficacy of biosimilars are likely to be needed; however, guidance on the design of and the need for any such studies is currently limited. The present article provides an overview of the current regulatory framework around the demonstration of interchangeability with biosimilars, with a specific focus on biosimilar insulin analogues, and details experiences with other biosimilar products. In addition, designs for studies to evaluate interchangeability with a biosimilar insulin analogue product are proposed and a discussion about the implications of interchangeability in clinical practice is included. © 2016 John Wiley & Sons Ltd.

  11. Caregiver Input to Optimize the Design of a Pediatric Care Planning Guide for Rehabilitation: Descriptive Study.

    Science.gov (United States)

    Khetani, Mary A; Lim, Heather K; Corden, Marya E

    2017-10-24

    Caregiver input has informed the design of a valid electronic patient-reported outcome (PRO) measure for use in pediatric rehabilitation. This proxy assessment may be further developed to expedite and enhance patient-centered care planning processes, but user input is first needed to finalize the core requirements that will guide its design. The objective of this study was to examine the feasibility of a stepwise process for building on a baseline assessment of young children's participation in activities to develop a care plan relevant to pediatric rehabilitation. A cross-sectional descriptive study design was employed using qualitative methods. Data were collected via Web-based technology and by telephone. Twenty-five caregivers of young children (9 with developmental delays, 16 without delays) and between 1 and 7 years were recruited from a subsample of parents who had previously enrolled in a Web-based validation of a PRO on children's participation and provided consent for future contact. Each caregiver completed a demographic questionnaire and Young Children's Participation and Environment Measure (YC-PEM) online, followed by a 20- to 60-min semistructured and audiotaped phone interview to review and build upon PRO results as summarized in an electronic report. Interview data were content coded to the interview guide and reviewed by multiple research staff to estimate feasibility according to stepwise completion rates, perceptions of difficulty in step completion, and perceptions of overall utility. Half of the participants in the final study sample (N=25) fully completed a stepwise process of building on their baseline PRO assessment to develop an initial care plan for their child. In most cases, similar stepwise completion rates and trends in the approaches taken for step completion were found regardless of the child's disability status. However, more parents of children with disabilities reported difficulties in rank ordering their priorities for change

  12. A job analysis design for the rail industry : description and model analysis of the job of freight conductor.

    Science.gov (United States)

    2013-10-01

    This document provides a step-by-step description of the design and execution of a strategic job analysis, using the position of Freight Conductor as an example. This document was created to be useful for many different needs, and can be used as an e...

  13. The development, description and appraisal of an emergent multimethod research design to study workforce changes in integrated care interventions

    NARCIS (Netherlands)

    Busetto, L.; Luijkx, K.G.; Calciolari, S.; González-ortiz, L.G.; Vrijhoef, H.J.M.

    In this paper, we provide a detailed and explicit description of the processes and decisions underlying and shaping the emergent multimethod research design of our study on workforce changes in integrated chronic care. The study was originally planned as mixed method research consisting of a pre-

  14. Movie Description

    OpenAIRE

    Rohrbach, A; A Torabi; Rohrbach, M.; Tandon, N.; C.; Pal; Larochelle, H; Courville, A.; Schiele, B.

    2017-01-01

    Audio Description (AD) provides linguistic descriptions of movies and allows visually impaired people to follow a movie along with their peers. Such descriptions are by design mainly visual and thus naturally form an interesting data source for computer vision and computational linguistics. In this work we propose a novel dataset which contains transcribed ADs, which are temporally aligned to full length movies. In addition we also collected and aligned movie scripts used in prior work and co...

  15. Human Health and Performance Aspects of the Mars Design Reference Mission

    Science.gov (United States)

    Charles, John B.

    2000-01-01

    This paper will describe the current planning for exploration-class missions, emphasizing the medical, and human factors aspects of such expeditions. The details of mission architecture are still under study, but a typical Mars design reference mission comprises a six-month transit from Earth to Mar, eighteen months in residence on Mars, and a six-month transit back to Earth. Physiological stressors will include environmental factors such as prolonged exposure to radiation, weightlessness in transit, and hypogravity and a toxic atmosphere while on Mars. Psychological stressors will include remoteness from Earth, confinement, and potential interpersonal conflicts, all complicated by circadian alterations. Medical risks including trauma must also be considered. Results of planning for assuring human health and performance will be presented.

  16. Technical Reference Suite Addressing Challenges of Providing Assurance for Fault Management Architectural Design

    Science.gov (United States)

    Fitz, Rhonda; Whitman, Gerek

    2016-01-01

    Research into complexities of software systems Fault Management (FM) and how architectural design decisions affect safety, preservation of assets, and maintenance of desired system functionality has coalesced into a technical reference (TR) suite that advances the provision of safety and mission assurance. The NASA Independent Verification and Validation (IV&V) Program, with Software Assurance Research Program support, extracted FM architectures across the IV&V portfolio to evaluate robustness, assess visibility for validation and test, and define software assurance methods applied to the architectures and designs. This investigation spanned IV&V projects with seven different primary developers, a wide range of sizes and complexities, and encompassed Deep Space Robotic, Human Spaceflight, and Earth Orbiter mission FM architectures. The initiative continues with an expansion of the TR suite to include Launch Vehicles, adding the benefit of investigating differences intrinsic to model-based FM architectures and insight into complexities of FM within an Agile software development environment, in order to improve awareness of how nontraditional processes affect FM architectural design and system health management. The identification of particular FM architectures, visibility, and associated IV&V techniques provides a TR suite that enables greater assurance that critical software systems will adequately protect against faults and respond to adverse conditions. Additionally, the role FM has with regard to strengthened security requirements, with potential to advance overall asset protection of flight software systems, is being addressed with the development of an adverse conditions database encompassing flight software vulnerabilities. Capitalizing on the established framework, this TR suite provides assurance capability for a variety of FM architectures and varied development approaches. Research results are being disseminated across NASA, other agencies, and the

  17. Final safety analysis report for the Galileo Mission: Volume 1, Reference design document

    Energy Technology Data Exchange (ETDEWEB)

    1988-05-01

    The Galileo mission uses nuclear power sources called Radioisotope Thermoelectric Generators (RTGs) to provide the spacecraft's primary electrical power. Because these generators contain nuclear material, a Safety Analysis Report (SAR) is required. A preliminary SAR and an updated SAR were previously issued that provided an evolving status report on the safety analysis. As a result of the Challenger accident, the launch dates for both Galileo and Ulysses missions were later rescheduled for November 1989 and October 1990, respectively. The decision was made by agreement between the DOE and the NASA to have a revised safety evaluation and report (FSAR) prepared on the basis of these revised vehicle accidents and environments. The results of this latest revised safety evaluation are presented in this document (Galileo FSAR). Volume I, this document, provides the background design information required to understand the analyses presented in Volumes II and III. It contains descriptions of the RTGs, the Galileo spacecraft, the Space Shuttle, the Inertial Upper Stage (IUS), the trajectory and flight characteristics including flight contingency modes, and the launch site. There are two appendices in Volume I which provide detailed material properties for the RTG.

  18. Mechanical design of the University of Florida Torsion Pendulum for testing the LISA Gravitational Reference Sensor

    Science.gov (United States)

    Shelley, Ryan; Chilton, Andrew; Olatunde, Tawio; Ciani, Giacomo; Mueller, Guido; Conklin, John

    2014-03-01

    The Laser Interferometer Space Antenna (LISA) requires free falling test masses, whose acceleration must be below 3 fm/s2/rtHz in the lower part of LISA's frequency band ranging from 0.1 to 100 mHz. Gravitational reference sensors (GRS) house the test masses, shield them from external disturbances, control their orientation, and sense their position at the nm/rtHz level. The GRS torsion pendulum is a laboratory test bed for GRS technology. By decoupling the system of test masses from the gravity of the Earth, it is possible to identify and quantify many sources of noise in the sensor. The mechanical design of the pendulum is critical to the study of the noise sources and the development of new technologies that can improve performance and reduce cost. The suspended test mass is a hollow, gold-coated, aluminum cube which rests inside a gold-coated, aluminum housing with electrodes for sensing and actuating all six degrees of freedom. This poster describes the design, analysis, and assembly of the mechanical subsystems of the UF Torsion Pendulum.

  19. The Semantic Automated Discovery and Integration (SADI Web service Design-Pattern, API and Reference Implementation

    Directory of Open Access Journals (Sweden)

    Wilkinson Mark D

    2011-10-01

    Full Text Available Abstract Background The complexity and inter-related nature of biological data poses a difficult challenge for data and tool integration. There has been a proliferation of interoperability standards and projects over the past decade, none of which has been widely adopted by the bioinformatics community. Recent attempts have focused on the use of semantics to assist integration, and Semantic Web technologies are being welcomed by this community. Description SADI - Semantic Automated Discovery and Integration - is a lightweight set of fully standards-compliant Semantic Web service design patterns that simplify the publication of services of the type commonly found in bioinformatics and other scientific domains. Using Semantic Web technologies at every level of the Web services "stack", SADI services consume and produce instances of OWL Classes following a small number of very straightforward best-practices. In addition, we provide codebases that support these best-practices, and plug-in tools to popular developer and client software that dramatically simplify deployment of services by providers, and the discovery and utilization of those services by their consumers. Conclusions SADI Services are fully compliant with, and utilize only foundational Web standards; are simple to create and maintain for service providers; and can be discovered and utilized in a very intuitive way by biologist end-users. In addition, the SADI design patterns significantly improve the ability of software to automatically discover appropriate services based on user-needs, and automatically chain these into complex analytical workflows. We show that, when resources are exposed through SADI, data compliant with a given ontological model can be automatically gathered, or generated, from these distributed, non-coordinating resources - a behaviour we have not observed in any other Semantic system. Finally, we show that, using SADI, data dynamically generated from Web services

  20. The Semantic Automated Discovery and Integration (SADI) Web service Design-Pattern, API and Reference Implementation

    Science.gov (United States)

    2011-01-01

    Background The complexity and inter-related nature of biological data poses a difficult challenge for data and tool integration. There has been a proliferation of interoperability standards and projects over the past decade, none of which has been widely adopted by the bioinformatics community. Recent attempts have focused on the use of semantics to assist integration, and Semantic Web technologies are being welcomed by this community. Description SADI - Semantic Automated Discovery and Integration - is a lightweight set of fully standards-compliant Semantic Web service design patterns that simplify the publication of services of the type commonly found in bioinformatics and other scientific domains. Using Semantic Web technologies at every level of the Web services "stack", SADI services consume and produce instances of OWL Classes following a small number of very straightforward best-practices. In addition, we provide codebases that support these best-practices, and plug-in tools to popular developer and client software that dramatically simplify deployment of services by providers, and the discovery and utilization of those services by their consumers. Conclusions SADI Services are fully compliant with, and utilize only foundational Web standards; are simple to create and maintain for service providers; and can be discovered and utilized in a very intuitive way by biologist end-users. In addition, the SADI design patterns significantly improve the ability of software to automatically discover appropriate services based on user-needs, and automatically chain these into complex analytical workflows. We show that, when resources are exposed through SADI, data compliant with a given ontological model can be automatically gathered, or generated, from these distributed, non-coordinating resources - a behaviour we have not observed in any other Semantic system. Finally, we show that, using SADI, data dynamically generated from Web services can be explored in a manner

  1. HDL cholesterol performance using an ultracentrifugation reference measurement procedure and the designated comparison method☆

    Science.gov (United States)

    Nakamura, Masakazu; Yokoyama, Shinji; Kayamori, Yuzo; Iso, Hiroyasu; Kitamura, Akihiko; Okamura, Tomonori; Kiyama, Masahiko; Noda, Hiroyuki; Nishimura, Kunihiro; Nakai, Michikazu; Koyama, Isao; Dasti, Mahnaz; Vesper, Hubert W.; Teramoto, Tamio; Miyamoto, Yoshihiro

    2017-01-01

    Background Accurate high-density lipoprotein cholesterol (HDL-C) measurements are important for management of cardiovascular diseases. The US Centers for Disease Control and Prevention (CDC) and Cholesterol Reference Method Laboratory Network (CRMLN) perform ultracentrifugation (UC) reference measurement procedure (RMP) to value assign HDL-C. Japanese CRMLN laboratory (Osaka) concurrently runs UC procedure and the designated comparison method (DCM). Osaka performance of UC and DCM was examined and compared with CDC RMP. Methods CDC RMP involved UC, heparin-MnCl2 precipitation, and cholesterol analysis. CRMLN DCM for samples containing <200 mg/dl triglycerides involved 50-kDa dextran sulfate-MgCl2 precipitation and cholesterol determination. Results HDL-C regression equations obtained with CDC (x) and Osaka (y) were y = 0.992x + 0.542 (R2 = 0.996) for Osaka UC and y = 1.004x − 0.181 (R2 = 0.998) for DCM. Pass rates within ±1 mg/dl of the CDC target value were 91.9 and 92.1% for Osaka UC and DCM, respectively. Biases at 40 mg/dl HDL-C were +0.22 and −0.02 mg/dl for Osaka UC and DCM, respectively. Conclusions Osaka UC and DCM were highly accurate, precise, and stable for many years, assisting manufacturers to calibrate products for clinical laboratories to accurately measure HDL-C for patients, calculate non-HDL-C, and estimate low-density lipoprotein cholesterol with the Friedewald equation. PMID:25444739

  2. Toward Meaningful Manufacturing Variation Data in Design - Feature Based Description of Variation in Manufacturing Processes

    DEFF Research Database (Denmark)

    Eifler, Tobias; Boorla, Srinivasa Murthy; Howard, Thomas J.

    2016-01-01

    by the availability of sophisticated methods and tools alone, but does evidently also depend on the accuracy of the input information used. As existing approaches for the description of manufacturing variation focus however, almost exclusively, on monitoring and controlling production processes, there is frequently...

  3. Design of video surveillance and tracking system based on attitude and heading reference system and PTZ camera

    Science.gov (United States)

    Yang, Jian; Xie, Xiaofang; Wang, Yan

    2017-04-01

    Based on the AHRS (Attitude and Heading Reference System) and PTZ (Pan/Tilt/Zoom) camera, we designed a video monitoring and tracking system. The overall structure of the system and the software design are given. The key technologies such as serial port communication and head attitude tracking are introduced, and the codes of the key part are given.

  4. REFERENCE MANUAL FOR RASSMIT VERSION 2.1: SUB-SLAB DEPRESSURIZATION SYSTEM DESIGN PERFORMANCE SIMULATION PROGRAM

    Science.gov (United States)

    The report is a reference manual for RASSMlT Version 2.1, a computer program that was developed to simulate and aid in the design of sub-slab depressurization systems used for indoor radon mitigation. The program was designed to run on DOS-compatible personal computers to ensure ...

  5. Design and Cohort Characteristics of the Social Spectrum Study: A Multicenter Study of the Autism Spectrum among Clinically Referred Children

    Science.gov (United States)

    Duvekot, Jorieke; Hoopen, Leontine W.; Slappendel, Geerte; van der Ende, Jan; Verhulst, Frank C.; van der Sijde, Ad; Greaves-Lord, Kirstin

    2017-01-01

    This paper provides an overview of the design and cohort characteristics of the Social Spectrum Study: a clinical cohort study that used a two-phase sampling design to identify children at risk for ASD. After screening 1281 children aged 2.5-10 years who had been consecutively referred to one of six mental health services in the Netherlands,…

  6. Vehicle occupancy detection camera position optimization using design of experiments and standard image references

    Science.gov (United States)

    Paul, Peter; Hoover, Martin; Rabbani, Mojgan

    2013-03-01

    Camera positioning and orientation is important to applications in domains such as transportation since the objects to be imaged vary greatly in shape and size. In a typical transportation application that requires capturing still images, inductive loops buried in the ground or laser trigger sensors are used when a vehicle reaches the image capture zone to trigger the image capture system. The camera in such a system is in a fixed position pointed at the roadway and at a fixed orientation. Thus the problem is to determine the optimal location and orientation of the camera when capturing images from a wide variety of vehicles. Methods from Design for Six Sigma, including identifying important parameters and noise sources and performing systematically designed experiments (DOE) can be used to determine an effective set of parameter settings for the camera position and orientation under these conditions. In the transportation application of high occupancy vehicle lane enforcement, the number of passengers in the vehicle is to be counted. Past work has described front seat vehicle occupant counting using a camera mounted on an overhead gantry looking through the front windshield in order to capture images of vehicle occupants. However, viewing rear seat passengers is more problematic due to obstructions including the vehicle body frame structures and seats. One approach is to view the rear seats through the side window. In this situation the problem of optimally positioning and orienting the camera to adequately capture the rear seats through the side window can be addressed through a designed experiment. In any automated traffic enforcement system it is necessary for humans to be able to review any automatically captured digital imagery in order to verify detected infractions. Thus for defining an output to be optimized for the designed experiment, a human defined standard image reference (SIR) was used to quantify the quality of the line-of-sight to the rear seats of

  7. Diffusive Barrier and Getter Under Waste Packages VA Reference Design Feature Evaluations

    Energy Technology Data Exchange (ETDEWEB)

    MacNeil, K.

    1999-05-24

    This technical document evaluates those aspects of the diffusive barrier and getter features which have the potential for enhancing the performance of the Viability Assessment Reference Design and are also directly related to the key attributes for the repository safety strategy of that design. The effects of advection, hydrodynamic dispersion, and diffusion on the radionuclide migration rates through the diffusive barrier were determined through the application of the one-dimensional, advection/dispersion/diffusion equation. The results showed that because advective flow described by the advection-dispersion equation dominates, the diffusive barrier feature alone would not be effective in retarding migration of radiocuclides. However, if the diffusive barrier were combined with one or more features that reduced the potential for advection, then transport of radionuclides would be dominated by diffusion and their migration from the EBS would be impeded. Apatite was chosen as the getter material used for this report. Two getter configurations were developed, Case 1 and Case 2. As in the evaluation of the diffusive barrier, the effects of advection, hydrodynamic dispersion, and diffusion on the migration of radionuclides through the getter are evaluated. However, in addition to these mechanisms, the one-dimensional advection/dispersion/diffusion model is modified to include the effect of sorption on radionuclide migration rates through the sorptive medium (getter). As a result of sorption, the longitudinal dispersion coefficient, and the average linear velocity are effectively reduced by the retardation factor. The retardation factor is a function of the getter material's dry bulk density, sorption coefficient and moisture content. The results of the evaluation showed that a significant delay in breakthrough through the getter can be achieved if the thickness of the getter barrier is increased.

  8. A Design Method of Code Correlation Reference Waveform in GNSS Based on Least-Squares Fitting.

    Science.gov (United States)

    Xu, Chengtao; Liu, Zhe; Tang, Xiaomei; Wang, Feixue

    2016-07-29

    The multipath effect is one of the main error sources in the Global Satellite Navigation Systems (GNSSs). The code correlation reference waveform (CCRW) technique is an effective multipath mitigation algorithm for the binary phase shift keying (BPSK) signal. However, it encounters the false lock problem in code tracking, when applied to the binary offset carrier (BOC) signals. A least-squares approximation method of the CCRW design scheme is proposed, utilizing the truncated singular value decomposition method. This algorithm was performed for the BPSK signal, BOC(1,1) signal, BOC(2,1) signal, BOC(6,1) and BOC(7,1) signal. The approximation results of CCRWs were presented. Furthermore, the performances of the approximation results are analyzed in terms of the multipath error envelope and the tracking jitter. The results show that the proposed method can realize coherent and non-coherent CCRW discriminators without false lock points. Generally, there is performance degradation in the tracking jitter, if compared to the CCRW discriminator. However, the performance promotions in the multipath error envelope for the BOC(1,1) and BPSK signals makes the discriminator attractive, and it can be applied to high-order BOC signals.

  9. Origins Space Telescope: Science Case and Design Reference Mission for Concept 1

    Science.gov (United States)

    Meixner, Margaret; Cooray, Asantha; Pope, Alexandra; Armus, Lee; Vieira, Joaquin Daniel; Milam, Stefanie N.; Melnick, Gary; Leisawitz, David; Staguhn, Johannes G.; Bergin, Edwin; Origins Space Telescope Science and Technology Definition Team

    2018-01-01

    The Origins Space Telescope (OST) is the mission concept for the Far-Infrared Surveyor, one of the four science and technology definition studies of NASA Headquarters for the 2020 Astronomy and Astrophysics Decadal survey. The science case for OST covers four themes: Tracing the Signature of Life and the Ingredients of Habitable Worlds; Charting the Rise of Metals, Dust and the First Galaxies, Unraveling the Co-evolution of Black Holes and Galaxies and Understanding Our Solar System in the Context of Planetary System Formation. Using a set of proposed observing programs from the community, we estimate a design reference mission for OST mission concept 1. The mission will complete significant programs in these four themes and have time for other programs from the community. Origins will enable flagship-quality general observing programs led by the astronomical community in the 2030s. We welcome you to contact the Science and Technology Definition Team (STDT) with your science needs and ideas by emailing us at ost_info@lists.ipac.caltech.edu.

  10. Design of a Model Reference Adaptive Controller for an Unmanned Air Vehicle

    Science.gov (United States)

    Crespo, Luis G.; Matsutani, Megumi; Annaswamy, Anuradha M.

    2010-01-01

    This paper presents the "Adaptive Control Technology for Safe Flight (ACTS)" architecture, which consists of a non-adaptive controller that provides satisfactory performance under nominal flying conditions, and an adaptive controller that provides robustness under off nominal ones. The design and implementation procedures of both controllers are presented. The aim of these procedures, which encompass both theoretical and practical considerations, is to develop a controller suitable for flight. The ACTS architecture is applied to the Generic Transport Model developed by NASA-Langley Research Center. The GTM is a dynamically scaled test model of a transport aircraft for which a flight-test article and a high-fidelity simulation are available. The nominal controller at the core of the ACTS architecture has a multivariable LQR-PI structure while the adaptive one has a direct, model reference structure. The main control surfaces as well as the throttles are used as control inputs. The inclusion of the latter alleviates the pilot s workload by eliminating the need for cancelling the pitch coupling generated by changes in thrust. Furthermore, the independent usage of the throttles by the adaptive controller enables their use for attitude control. Advantages and potential drawbacks of adaptation are demonstrated by performing high fidelity simulations of a flight-validated controller and of its adaptive augmentation.

  11. System Design Description and Requirements for Modeling the Off-Gas Systems for Fuel Recycling Facilities

    Energy Technology Data Exchange (ETDEWEB)

    Daryl R. Haefner; Jack D. Law; Troy J. Tranter

    2010-08-01

    This document provides descriptions of the off-gases evolved during spent nuclear fuel processing and the systems used to capture the gases of concern. Two reprocessing techniques are discussed, namely aqueous separations and electrochemical (pyrochemical) processing. The unit operations associated with each process are described in enough detail so that computer models to mimic their behavior can be developed. The document also lists the general requirements for the desired computer models.

  12. Acquisition of teleological descriptions

    Science.gov (United States)

    Franke, David W.

    1992-03-01

    Teleology descriptions capture the purpose of an entity, mechanism, or activity with which they are associated. These descriptions can be used in explanation, diagnosis, and design reuse. We describe a technique for acquiring teleological descriptions expressed in the teleology language TeD. Acquisition occurs during design by observing design modifications and design verification. We demonstrate the acquisition technique in an electronic circuit design.

  13. Virtual World, Real Education: A Descriptive Study of Instructional Design in Second Life

    Science.gov (United States)

    Kingston, Linda S.

    2011-01-01

    Virtual worlds like Second Life are emerging technologies that have gained popularity among educators. As these worlds emerged, greater focus has been placed on the design of the environments themselves rather than the design of instruction within them. Educators have begun using these environments for teaching and instructional designers are now…

  14. FirefOx Design Reference fO2 Sensor for Hot, Deep Atmospheres

    Science.gov (United States)

    Izenberg, N.; Papadakis, S.; Deglau, D.; Francomacaro, A. S.

    2016-12-01

    Understanding the composition of the lowest portion of Venus' atmosphere is critical to knowing the stable mineralogy of the rocks there. Oxygen gas is a critical trace component, with fugacity, or partial pressure, estimated in the range of 10-19 to 10-22 from early probe measurements down to 22km altitude (Pioneer Venus, Venera), chemical equilibrium measurements, and other modeling. "FirefOx" is a simple oxygen fugacity sensor with the express purpose of determining the partial pressure of oxygen in the lowest scale heights of the Venus atmosphere, and especially the lowest hundreds of meters; the surface atmosphere interface, where the atmosphere and surface move to thermodynamic equilibrium. Knowledge of the fO2 at the surface atmosphere interface is crucial to determining the stable mineralogy of surface materials (e.g. magnetite vs. hematite) and gas chemistry in the near-surface atmosphere FirefOx is a Metal/Metal Oxide oxygen fugacity sensor intended to be mounted on the outside of a Venus descent probe, with electronics housed inside a thermally controlled environment. The sole sensor capability is the precise, accurate detection of the partial pressure of oxygen gas (fO2) in the near-surface environment of Venus, at up to 95-bar pressure (predominantly CO2. Surface temperatures at mean planetary elevation are near 735 K, thus a required operational temperature range of 710-740 K covers a range of near-surface elevations. FirefOx system requirements are low ( 100-200 grams, mass, milliwatt power, several kilobytes total science data). A design reference sensor, composed of custom, Yittria-ZrO ceramic electrolyte, with an encapsulated Pd/PdO standard and patterned Pt electrodes has demonstrated scientifically useful signal-to-noise millivolt level potential at temperatures as low as 620 K, relatable to fO2 by a Nernst equation E = RT/4F ln(PO2/PrefO2) where E = open circuit potential across the sensor electrolyte, R = universal gas constant, T

  15. A descriptive roadmap: how to design for SWB? Interpreting design results in the field of subjective well-being

    OpenAIRE

    STEVENS, Ruth

    2014-01-01

    Today’s public discourse on the design of care centers for the elderly population is increasingly emphasizing the importance of subjective well-being (SWB) and the value that architecture and interior architecture can have in this context. A design exercise was formulated for 10 groups of 4 master students in interior architecture in which they had to rethink the design of the communal space system of an existing residential care center (RCC) with the purpose of augmenting the living experien...

  16. FOR A UNIFORM SYSTEM OF GRADING AND DESIGNATION IN DESCRIPTIVE GEOMETRY

    Directory of Open Access Journals (Sweden)

    ALDEA Sorin

    2013-06-01

    Full Text Available A general approach to a systems of symbols used in descriptive geometry is proposed. This is seen as the starting point of a discussion on the necessity of agreeing on a unitary system which would be both logical and efficient. This system could be used both in the teaching process and in current engineering applications, especially those carried out on computers. Such a unitary system has be come a matter of utmost necessity once the information sources and the possibilities of dissemination have diversified, in on ever larger context.

  17. A Reference Architecture for Provisioning of Tools as a Service: Meta-Model, Ontologies and Design Elements

    DEFF Research Database (Denmark)

    Chauhan, Muhammad Aufeef; Babar, Muhammad Ali; Sheng, Quan Z.

    2016-01-01

    Software Architecture (SA) plays a critical role in designing, developing and evolving cloud-based platforms that can be used to provision different types of services to consumers on demand. In this paper, we present a Reference Architecture (RA) for designing cloud-based Tools as a service SPACE...... (TSPACE) for provisioning a bundled suite of tools by following the Software as a Service (SaaS) model. The reference architecture has been designed by leveraging information structuring approaches and by using well-known architecture design principles and patterns. The RA has been documented using view...... to provision tools for software architecting. We have also evaluated the RA in terms of effectiveness of the design decisions and the RA’s completeness and feasibility using scenario-based architecture evaluation method. The proposed TSPACE RA can provide valuable insights to information structure approaches...

  18. A Reference Architecture for Provisioning of Tools as a Service: Meta-Model, Ontologies and Design Elements

    DEFF Research Database (Denmark)

    Chauhan, Muhammad Aufeef; Babar, Muhammad Ali; Sheng, Quan Z.

    2016-01-01

    to provision tools for software architecting. We have also evaluated the RA in terms of effectiveness of the design decisions and the RA’s completeness and feasibility using scenario-based architecture evaluation method. The proposed TSPACE RA can provide valuable insights to information structure approaches......Software Architecture (SA) plays a critical role in designing, developing and evolving cloud-based platforms that can be used to provision different types of services to consumers on demand. In this paper, we present a Reference Architecture (RA) for designing cloud-based Tools as a service SPACE...... (TSPACE) for provisioning a bundled suite of tools by following the Software as a Service (SaaS) model. The reference architecture has been designed by leveraging information structuring approaches and by using well-known architecture design principles and patterns. The RA has been documented using view...

  19. Design and control of energy efficient drying processes with specific reference to foods

    Energy Technology Data Exchange (ETDEWEB)

    Franzen, K.; Kim, M.; Liang, H.; Murakami, E.; Narsimhan, G.; Okos, M.; Singh, R.; Waananen, K.; Xiong, X.

    1988-07-15

    This report contains a detailed summary of all work performed to date. Task 10 involves a comprehensive review of drying theory. Proposed mass transfer mechanisms include liquid and vapor diffusion, capillary flow, surface diffusion, hydrodynamic flow, and evaporation/condensation processes. Pasta was chosen as a model system in this project since it is macroscopically homogenous and can be made under controlled conditions. Task 11 involves experimental drying studies. A high pressure drying apparatus is available for studies related to the revision of the fundamental drying model. The dryer will require two major modifications for the planned tests: installation of a pressure control valve and recirculation of exhaust gas. A tray dryer was used to measure the shrinkage coefficient of nonfat milk, and will be used for further tests on nonfat milk, as well as whey and tomato puree. A method of economic analysis regarding use of mechanical vapor recompression is presented. Task 12 involves food quality studies. A model of nonenzymatic browning (NEB) was developed based on NEB in skim milk samples containing 3.5--50% moisture, exposed to temperatures of 35--130{degrees}C. The browning rate was zero order after a lag period, and the temperature dependence fit an Arrhenius relation. The critical moisture occurs between 4% and 11% moisture. Task 13 addresses recommendations and strategies for dryer design and control. Moisture sensors were reviewed with specific reference to their on-line applicability. The IR sensor was found to be the most promising. Task 14 examined moisture mobility and interaction in foods. The BET adsorption method using nitrogen gas was applied to pasta, skim milk and egg albumin systems. The data obtained do not show good reproducibility, possibly due to an inadequate sample size. The possibility of using water vapor adsorption will be studied in future experiments. 210 refs., 30 figs., 22 tabs. (MHB)

  20. Colored Gaussian Multiple Descriptions: Spectral-Domain Characterization and Time-Domain Design

    CERN Document Server

    Ostergaard, Jan; Zamir, Ram

    2010-01-01

    It is well known that Shannon's rate-distortion function (RDF) in the colored quadratic Gaussian (QG) case, can be parametrized via a single Lagrangian variable (the ``water level'' in the reverse water filling solution). In this work, we show that the symmetric colored QG multiple-description (MD) RDF in the case of two descriptions, can be parametrized via two Lagrangian variables. To establish this result, we use two key ideas. First, we propose a new representation for the MD test channel, and show that the minimum mutual information rate across this channel coincide with the QG MD RDF. Second, we use variational calculus to obtain a spectral domain representation of the test channel's optimal side and central distortion spectra given the source spectral density and the side and central distortion constraints. The distortion spectra are specified via two Lagrangian parameters, which control the trade-off between the side distortion, the central distortion, and the coding rate.We also show that the symmetr...

  1. Cold Vacuum Drying facility HVAC system design description (SYS 30-1 THRU 30-5)

    Energy Technology Data Exchange (ETDEWEB)

    PITKOFF, C.C.

    1999-07-02

    This document describes the Cold Vacuum Drying Facility (CVDF) heating, ventilation, and air conditioning system (HVAC). The CVDF HVAC system consists of the Administrative building HVAC system, the process bay recirculation HVAC system, the process bay local HVAC and process vent system, the process general supply/exhaust HVAC system, and the Reference air system. These HVAC sub-systems support the CVDF process and provide secondary confinement of contamination and the required filtration of exhaust.

  2. REFERENCE GRAMMAR OF LITERARY DHIMOTIKI.

    Science.gov (United States)

    HOUSEHOLDER, FRED W.; AND OTHERS

    BASED ON A TRADITIONAL APPROACH, THIS REFERENCE GRAMMAR OF LITERARY DHIMOTIKI IS DESIGNED TO BE MOST USEFUL TO ADVANCED UNDERGRADUATES OR BEGINNING GRADUATE STUDENTS OF GREEK. (DHIMOTIKI, OR DEMOTIC, IS THE POPULAR FORM OF MODERN GREEK.) IN PART I THERE IS AN EXTENSIVE DESCRIPTION OF THE PHONOLOGICAL SYSTEM FOLLOWED BY A DISCUSSION OF THE WRITING…

  3. Designing image segmentation studies: Statistical power, sample size and reference standard quality.

    Science.gov (United States)

    Gibson, Eli; Hu, Yipeng; Huisman, Henkjan J; Barratt, Dean C

    2017-12-01

    Segmentation algorithms are typically evaluated by comparison to an accepted reference standard. The cost of generating accurate reference standards for medical image segmentation can be substantial. Since the study cost and the likelihood of detecting a clinically meaningful difference in accuracy both depend on the size and on the quality of the study reference standard, balancing these trade-offs supports the efficient use of research resources. In this work, we derive a statistical power calculation that enables researchers to estimate the appropriate sample size to detect clinically meaningful differences in segmentation accuracy (i.e. the proportion of voxels matching the reference standard) between two algorithms. Furthermore, we derive a formula to relate reference standard errors to their effect on the sample sizes of studies using lower-quality (but potentially more affordable and practically available) reference standards. The accuracy of the derived sample size formula was estimated through Monte Carlo simulation, demonstrating, with 95% confidence, a predicted statistical power within 4% of simulated values across a range of model parameters. This corresponds to sample size errors of less than 4 subjects and errors in the detectable accuracy difference less than 0.6%. The applicability of the formula to real-world data was assessed using bootstrap resampling simulations for pairs of algorithms from the PROMISE12 prostate MR segmentation challenge data set. The model predicted the simulated power for the majority of algorithm pairs within 4% for simulated experiments using a high-quality reference standard and within 6% for simulated experiments using a low-quality reference standard. A case study, also based on the PROMISE12 data, illustrates using the formulae to evaluate whether to use a lower-quality reference standard in a prostate segmentation study. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

  4. Computer system design description for the spare pump mini-dacs data acquisition and control system

    Energy Technology Data Exchange (ETDEWEB)

    Vargo, G.F. Jr.

    1994-09-29

    The attached document outlines the computer software design for the mini data acquisition and control system (DACS), that supports the testing of the spare pump for Tank 241-SY-101, at the maintenance and storage facility (MASF).

  5. A Graph-Based Approach to Optimal Scan Chain Stitching Using RTL Design Descriptions

    Directory of Open Access Journals (Sweden)

    Lilia Zaourar

    2012-01-01

    Full Text Available The scan chain insertion problem is one of the mandatory logic insertion design tasks. The scanning of designs is a very efficient way of improving their testability. But it does impact size and performance, depending on the stitching ordering of the scan chain. In this paper, we propose a graph-based approach to a stitching algorithm for automatic and optimal scan chain insertion at the RTL. Our method is divided into two main steps. The first one builds graph models for inferring logical proximity information from the design, and then the second one uses classic approximation algorithms for the traveling salesman problem to determine the best scan-stitching ordering. We show how this algorithm allows the decrease of the cost of both scan analysis and implementation, by measuring total wirelength on placed and routed benchmark designs, both academic and industrial.

  6. Design of automata theory of cubical complexes with applications to diagnosis and algorithmic description

    Science.gov (United States)

    Roth, J. P.

    1972-01-01

    Methods for development of logic design together with algorithms for failure testing, a method for design of logic for ultra-large-scale integration, extension of quantum calculus to describe the functional behavior of a mechanism component-by-component and to computer tests for failures in the mechanism using the diagnosis algorithm, and the development of an algorithm for the multi-output 2-level minimization problem are discussed.

  7. Descriptive study of symptomatic epilepsy by age of onset in patients with a 3-year follow-up at the Neuropaediatric Department of a reference centre.

    Science.gov (United States)

    Ochoa-Gómez, L; López-Pisón, J; Fuertes-Rodrigo, C; Fernando-Martínez, R; Samper-Villagrasa, P; Monge-Galindo, L; Peña-Segura, J L; García-Jiménez, M C

    2017-09-01

    We conducted a descriptive study of symptomatic epilepsy by age at onset in a cohort of patients who were followed up at a neuropaediatric department of a reference hospital over a 3-year period PATIENTS AND METHODS: We included all children with epilepsy who were followed up from January 1, 2008 to December 31, 2010 RESULTS: Of the 4595 children seen during the study period, 605 (13.17%) were diagnosed with epilepsy; 277 (45.79%) of these had symptomatic epilepsy. Symptomatic epilepsy accounted for 67.72% and 61.39% of all epilepsies starting before one year of age, or between the ages of one and 3, respectively. The aetiologies of symptomatic epilepsy in our sample were: prenatal encephalopathies (24.46% of all epileptic patients), perinatal encephalopathies (9.26%), post-natal encephalopathies (3.14%), metabolic and degenerative encephalopathies (1.98%), mesial temporal sclerosis (1.32%), neurocutaneous syndromes (2.64%), vascular malformations (0.17%), cavernomas (0.17%), and intracranial tumours (2.48%). In some aetiologies, seizures begin before the age of one; these include Down syndrome, genetic lissencephaly, congenital cytomegalovirus infection, hypoxic-ischaemic encephalopathy, metabolic encephalopathies, and tuberous sclerosis. The lack of a universally accepted classification of epileptic syndromes makes it difficult to compare series from different studies. We suggest that all epilepsies are symptomatic because they have a cause, whether genetic or acquired. The age of onset may point to specific aetiologies. Classifying epilepsy by aetiology might be a useful approach. We could establish 2 groups: a large group including epileptic syndromes with known aetiologies or associated with genetic syndromes which are very likely to cause epilepsy, and another group including epileptic syndromes with no known cause. Thanks to the advances in neuroimaging and genetics, the latter group is expected to become increasingly smaller. Copyright © 2016 Sociedad Espa

  8. System design description for ``Mini-DACS`` data acquisition and control system

    Energy Technology Data Exchange (ETDEWEB)

    Ermi, A.M.

    1996-10-01

    This document describes the computer software design and associated hardware for the Mini-DACS (Data Acquisition and Control System) in support of testing the second spare pump (HMR-3) for tank 241SY101. The testing of HMR-3 was conducted at the Maintenance and Storage Facility (MASF).

  9. Preliminary design of the Carrisa Plains solar central receiver power plant. Volume III, Book 1. Design description

    Energy Technology Data Exchange (ETDEWEB)

    1983-12-31

    The design of the 30 MWe central receiver solar power plant to be located at Carrisa Plains, San Luis Obispo County, California, is summarized. The plant uses a vertical flat-panel (billboard solar receiver located at the top of a tower to collect solar energy redirected by approximately 1900 heliostats located to the north of the tower. The solar energy is used to heat liquid sodium pumped from ground level from 610 to 1050/sup 0/F. The power conversion system is a non-reheat system, cost-effective at this size level, and designed for high-efficiency performance in an application requiring daily startup. Successful completion of this project will lead to power generation starting in 1986. This report discusses in detail the design of the collector system, heat transport system, thermal storage subsystem, heat transport loop, steam generation subsystem, electrical, instrumentation, and control systems, power conversion system, master control system, and balance of plant. The performance, facility cost estimate and economic analysis, and development plan are also discussed.

  10. Testing a discrete choice experiment including duration to value health states for large descriptive systems: addressing design and sampling issues.

    Science.gov (United States)

    Bansback, Nick; Hole, Arne Risa; Mulhern, Brendan; Tsuchiya, Aki

    2014-08-01

    There is interest in the use of discrete choice experiments that include a duration attribute (DCETTO) to generate health utility values, but questions remain on its feasibility in large health state descriptive systems. This study examines the stability of DCETTO to estimate health utility values from the five-level EQ-5D, an instrument with depicts 3125 different health states. Between January and March 2011, we administered 120 DCETTO tasks based on the five-level EQ-5D to a total of 1799 respondents in the UK (each completed 15 DCETTO tasks on-line). We compared models across different sample sizes and different total numbers of observations. We found the DCETTO coefficients were generally consistent, with high agreement between individual ordinal preferences and aggregate cardinal values. Keeping the DCE design and the total number of observations fixed, subsamples consisting of 10 tasks per respondent with an intermediate sized sample, and 15 tasks with a smaller sample provide similar results in comparison to the whole sample model. In conclusion, we find that the DCETTO is a feasible method for developing values for larger descriptive systems such as EQ-5D-5L, and find evidence supporting important design features for future valuation studies that use the DCETTO. Copyright © 2014 The Authors. Published by Elsevier Ltd.. All rights reserved.

  11. DESCRIPTION OF MODELING ANALYSES IN SUPPORT OF THE 200-ZP-1 REMEDIAL DESIGN/REMEDIAL ACTION

    Energy Technology Data Exchange (ETDEWEB)

    VONGARGEN BH

    2009-11-03

    The Feasibility Study/or the 200-ZP-1 Groundwater Operable Unit (DOE/RL-2007-28) and the Proposed Plan/or Remediation of the 200-ZP-1 Groundwater Operable Unit (DOE/RL-2007-33) describe the use of groundwater pump-and-treat technology for the 200-ZP-1 Groundwater Operable Unit (OU) as part of an expanded groundwater remedy. During fiscal year 2008 (FY08), a groundwater flow and contaminant transport (flow and transport) model was developed to support remedy design decisions at the 200-ZP-1 OU. This model was developed because the size and influence of the proposed 200-ZP-1 groundwater pump-and-treat remedy will have a larger areal extent than the current interim remedy, and modeling is required to provide estimates of influent concentrations and contaminant mass removal rates to support the design of the aboveground treatment train. The 200 West Area Pre-Conceptual Design/or Final Extraction/Injection Well Network: Modeling Analyses (DOE/RL-2008-56) documents the development of the first version of the MODFLOW/MT3DMS model of the Hanford Site's Central Plateau, as well as the initial application of that model to simulate a potential well field for the 200-ZP-1 remedy (considering only the contaminants carbon tetrachloride and technetium-99). This document focuses on the use of the flow and transport model to identify suitable extraction and injection well locations as part of the 200 West Area 200-ZP-1 Pump-and-Treat Remedial Design/Remedial Action Work Plan (DOEIRL-2008-78). Currently, the model has been developed to the extent necessary to provide approximate results and to lay a foundation for the design basis concentrations that are required in support of the remedial design/remediation action (RD/RA) work plan. The discussion in this document includes the following: (1) Assignment of flow and transport parameters for the model; (2) Definition of initial conditions for the transport model for each simulated contaminant of concern (COC) (i.e., carbon

  12. Design and test of an artificial reference cow to simulate methane release through exhalation

    NARCIS (Netherlands)

    Wu, Liansun; Groot Koerkamp, P.W.G.; Ogink, N.W.M.

    2015-01-01

    To mitigate methane emission from dairy cows, a technique is needed to evaluate individual methane emission from a large number of cows under practical conditions in barns. For developing such a measurement technique, a known reference source that can simulate cow exhalation of methane would be a

  13. UAS-NAS Live Virtual Constructive Distributed Environment (LVC): LVC Gateway, Gateway Toolbox, Gateway Data Logger (GDL), SaaProc Software Design Description

    Science.gov (United States)

    Jovic, Srboljub

    2015-01-01

    This document provides the software design description for the two core software components, the LVC Gateway, the LVC Gateway Toolbox, and two participants, the LVC Gateway Data Logger and the SAA Processor (SaaProc).

  14. Advanced human-system interface design review guideline. General evaluation model, technical development, and guideline description

    Energy Technology Data Exchange (ETDEWEB)

    O`Hara, J.M.

    1994-07-01

    Advanced control rooms will use advanced human-system interface (HSI) technologies that may have significant implications for plant safety in that they will affect the operator`s overall role in the system, the method of information presentation, and the ways in which operators interact with the system. The U.S. Nuclear Regulatory Commission (NRC) reviews the HSI aspects of control rooms to ensure that they are designed to good human factors engineering principles and that operator performance and reliability are appropriately supported to protect public health and safety. The principal guidance available to the NRC, however, was developed more than ten years ago, well before these technological changes. Accordingly, the human factors guidance needs to be updated to serve as the basis for NRC review of these advanced designs. The purpose of this project was to develop a general approach to advanced HSI review and the human factors guidelines to support NRC safety reviews of advanced systems. This two-volume report provides the results of the project. Volume I describes the development of the Advanced HSI Design Review Guideline (DRG) including (1) its theoretical and technical foundation, (2) a general model for the review of advanced HSIs, (3) guideline development in both hard-copy and computer-based versions, and (4) the tests and evaluations performed to develop and validate the DRG. Volume I also includes a discussion of the gaps in available guidance and a methodology for addressing them. Volume 2 provides the guidelines to be used for advanced HSI review and the procedures for their use.

  15. The INTERPHONE study: design, epidemiological methods, and description of the study population

    DEFF Research Database (Denmark)

    Cardis, Elisabeth; Richardson, Lesley; Deltour, Isabelle

    2007-01-01

    The very rapid worldwide increase in mobile phone use in the last decade has generated considerable interest in the possible health effects of exposure to radio frequency (RF) fields. A multinational case-control study, INTERPHONE, was set-up to investigate whether mobile phone use increases....... This paper describes the study design and methods and the main characteristics of the study population. INTERPHONE is the largest case-control study to date investigating risks related to mobile phone use and to other potential risk factors for the tumours of interest and includes 2,765 glioma, 2...

  16. Integrated security systems design a complete reference for building enterprise-wide digital security systems

    CERN Document Server

    Norman, Thomas L

    2014-01-01

    Integrated Security Systems Design, 2nd Edition, is recognized as the industry-leading book on the subject of security systems design. It explains how to design a fully integrated security system that ties together numerous subsystems into one complete, highly coordinated, and highly functional system. With a flexible and scalable enterprise-level system, security decision makers can make better informed decisions when incidents occur and improve their operational efficiencies in ways never before possible. The revised edition covers why designing an integrated security system is essential a

  17. Steam Reforming, 6-in. Bench-Scale Design and Testing Project -- Technical and Functional Requirements Description

    Energy Technology Data Exchange (ETDEWEB)

    Losinski, Sylvester John; Marshall, Douglas William

    2002-08-01

    Feasibility studies and technology development work are currently being performed on several processes to treat radioactive liquids and solids currently stored at the Idaho Nuclear Technology and Engineering Center (INTEC), located within the Idaho National Engineering and Environmental Laboratory (INEEL). These studies and development work will be used to select a treatment process for treatment of the radioactive liquids and solids to meet treatment milestones of the Settlement Agreement between the Department of Energy and the State of Idaho. One process under consideration for treating the radioactive liquids and solids, specifically Sodium-Bearing Waste (SBW) and tank heel solids, is fluid bed steam reforming (FBSR). To support both feasibility and development studies a bench-scale FBSR is being designed and constructed. This report presents the technical and functional requirements, experimental objectives, process flow sheets, and equipment specifications for the bench-scale FBSR.

  18. Plasma source by microwaves: design description; Fuente de plasma por microondas: descripcion de diseno

    Energy Technology Data Exchange (ETDEWEB)

    Camps, E.; Olea, O.; Andrade, R.; Anguiano, G

    1992-03-15

    The design of a device for the formation of a plasma with densities of the order of 10{sup 12} cm{sup -} {sup 3} and low temperatures (T{sub e} {approx} 40 eV) is described. For such purpose it was carried out in the device a microwave discharge (f{sub o} = 2.45 GHz) in a resonator of high Q factor, immersed in a static external magnetic field. The device worked in the regime {omega}{sub ce} {<=} {omega}{sub o}/2 ({omega}{sub ce}- cyclotron frequency of the electrons, ({omega}{sub o} = 2 {pi} f{sub o}) where is possible the excitement of non lineal phenomena of waves transformation. (Author)

  19. Take A Trip Reference Manual: An Authoring and Storage System for Designing and Sharing Challenging Curriculum.

    Science.gov (United States)

    Minnesota State Dept. of Education, St. Paul. Evaluation Section.

    The Take a Trip program is an authoring and storage system for designing challenging curriculum. Using the power of hypermedia, specifically Apple Computer's HyperCard, Take a Trip provides course file stacks, help stacks, and personalized learning plan stacks. Designed to assist the user when new units are written, the help stacks provide an…

  20. TRIGA OCEANOGRAPHIC POWER SUPPLY FOR A MANNED UNDERWATER STATION. VOLUME I. REFERENCE DESIGN.

    Science.gov (United States)

    The TRIGA Oceanographic Power Supply (TOPS) is designed to provide 100 kw of electrical power for a Manned Underwater Station (MUS). The design is... TRIGA research reactor. It contains the entire pressurized water primary coolant circuit and the steam generator. The U-ZrH-fueled, water-cooled core

  1. Design and realization of the high-precision weighing systems as the gravimetric references in PTB's national water flow standard

    Science.gov (United States)

    Engel, Rainer; Beyer, Karlheinz; Baade, Hans-Joachim

    2012-07-01

    PTB's ‘Hydrodynamic Test Field’, which represents a high-accuracy water flow calibration facility, serves as the national primary standard for liquid flow measurands. As the core reference device of this flow facility, a gravimetric standard has been incorporated, which comprises three special-design weighing systems: 300 kg, 3 tons and 30 tons. These gravimetric references were realized as a combination of a strain-gauge-based and an electromagnetic-force-compensation load-cell-based balance, each. Special emphasis had to be placed upon the dynamics design of the whole weighing system, due to the high measurement resolution and the dynamic behavior of the weighing systems, which are dynamically affected by mechanical vibrations caused by environmental impacts, flow machinery operation, flow noise in the pipework and induced wave motions in the weigh tanks. Taking into account all the above boundary conditions, the design work for the gravimetric reference resulted in a concrete foundation ‘rock’ of some 300 tons that rests on a number of vibration isolators. In addition to these passively operating vibration isolators, the vibration damping effect is enhanced by applying an electronic level regulation device.

  2. Lexical References to Sensory Modalities in Verbal Descriptions of People and Objects by Congenitally Blind, Late Blind and Sighted Adults: e44020

    National Research Council Canada - National Science Library

    Valérie Chauvey; Yvette Hatwell; Bertrand Verine; Gwenael Kaminski; Edouard Gentaz

    2012-01-01

    ...'), references to auditory and tactile attributes are scarcer. However, this statement may be challenged by current theories claiming that cognition is linked to the perceptions and actions from which it...

  3. Japanese structure survey of radiation oncology in 2009 with special reference to designated cancer care hospitals.

    Science.gov (United States)

    Numasaki, Hodaka; Nishio, Masamichi; Ikeda, Hiroshi; Sekiguchi, Kenji; Kamikonya, Norihiko; Koizumi, Masahiko; Tago, Masao; Ando, Yutaka; Tsukamoto, Nobuhiro; Terahara, Atsuro; Nakamura, Katsumasa; Nishimura, Tetsuo; Murakami, Masao; Takahashi, Mitsuhiro; Teshima, Teruki

    2013-10-01

    The structure of radiation oncology in designated cancer care hospitals in Japan was surveyed in terms of equipment, personnel, patient load, and geographic distribution, and compared with the structure in other radiotherapy facilities and the previous survey. The Japanese Society for Therapeutic Radiology and Oncology surveyed the national structure of radiation oncology in 2009. The structures of 365 designated cancer care hospitals and 335 other radiotherapy facilities were compared. Designated cancer care hospitals accounted for 50.0% of all the radiotherapy facilities in Japan. The patterns of equipment and personnel in designated cancer care hospitals and the other radiotherapy facilities were, respectively, as follows: linear accelerators per facility: 1.4 and 1.0; dual-energy function: 78.6 and 61.3%; three-dimensional conformal radiotherapy function: 88.5 and 70.0%; intensity-modulated radiotherapy function: 51.6 and 25.3%; annual number of patients per linear accelerator: 301.3 and 185.2; Ir-192 remote-controlled after-loading systems: 31.8 and 4.2%; and average number of full-time equivalent radiation oncologists per facility: 1.8 and 0.8. Compared with the previous survey, the ownership ratio of equipment and personnel improved in both designated cancer care hospitals and the other radiotherapy facilities. Annual patient loads per full-time equivalent radiation oncologist in the designated cancer care hospitals and the other radiotherapy facilities were 225.5 and 247.6, respectively. These values exceeded the standard guidelines level of 200. The structure of radiation oncology in designated Japanese cancer care hospitals was more mature than that in the other radiotherapy facilities. There is still a shortage of personnel. The serious understaffing problem in radiation oncology should be corrected in the future.

  4. Participatory Communication Referred to Meta-Design Approach through the FleXpeaker™ Application of Innovative Material in Exhibition Design

    Directory of Open Access Journals (Sweden)

    Pei-Hsuan Su

    2016-07-01

    Full Text Available Modelling a communication system in material culture today always involves with objects, people, organizations, activities and interrelationships among them. The researcher suggests bringing together stakeholders engaged to exchange ideas, which the interactions relate to multiple professions and disciplines in a participatory scope of communication system. Owing to the invention of digital media, the status quo of images and sounds has revolutionized and caused changes of the mode of art exhibitions that produce activities and aesthetic concepts in terms of numerical representation, modularity, automation, visual variability and transcoding. Underlying a participatory-design approach, the research emphasizes a co-creative meta-interpretation of museum‟s visitors. In addition, the research delves further into the use of new media-FleXpeaker™ [ITRI], as the carrier. Combining art and design with innovative technology, the research focuses on examining design objects and innovative material which are applied in new media art and exhibition, in the hope to find new angles of participatory interpretation of the “integrated innovation” in curating an exhibition.

  5. Tautomers and reference 3D-structures: the orphans of in silico drug design

    Science.gov (United States)

    Clark, Timothy

    2010-06-01

    The importance of calculating not only the correct tautomer, but also the correct protonation state and conformation in 3D modeling applications is emphasized. Above all, identifying and characterizing the most stable form of a ligand under physiological conditions is seen to be the key to successful 3D modeling. Modeling strategies that make use of the performance of modern hardware can employ physically more appropriate models than most currently in use and still be easily applicable to large numbers of compounds. Because the performance of quantitative structure-property relationships is likely to be limited by the available training and validation data, we must either find new sources of such data or resort to explicit modeling, which can partly be parameterized using definitive ab initio calculations for reference data such as gas-phase proton affinities.

  6. An Electronic Service Quality Reference Model for Designing E-Commerce Websites Which Maximizes Customer Satisfaction

    Science.gov (United States)

    Shaheen, Amer N.

    2011-01-01

    This research investigated Electronic Service Quality (E-SQ) features that contribute to customer satisfaction in an online environment. The aim was to develop an approach which improves E-CRM processes and enhances online customer satisfaction. The research design adopted mixed methods involving qualitative and quantitative methods to…

  7. Durability-Based Design Properties of Reference Crossply Carbon-Fiber Composite

    Energy Technology Data Exchange (ETDEWEB)

    Corum, J.M.

    2001-04-16

    This report provides recommended durability-based design properties and criteria for a crossply carbon-fiber composite for possible automotive structural applications. Although the composite utilized aerospace-grade carbon-fiber reinforcement, it was made by a rapid-molding process suitable for high-volume automotive use. The material is the first in a planned progression of candidate composites to be characterized as part of an Oak Ridge National Laboratory project entitled Durability of Carbon-Fiber Composites. The overall goal of the project, which is sponsored by the U.S. Department of Energy's Office of Advanced Automotive Technologies and is closely coordinated with the Advanced Composites Consortium, is to develop durability-driven design data and criteria to assure the long-term integrity of carbon-fiber-based composite systems for automotive structural applications. The composite addressed in this report is a ({+-}45{degree})3S crossply consisting of continuous Thornel T300 fibers in a Baydur 420 IMR urethane matrix. This composite is highly anisotropic with two dominant fiber orientations--0/90{degree} and {+-}45{degree}. Properties and models were developed for both orientations. This document is in two parts. Part 1 provides design data and correlations, while Part 2 provides the underlying experimental data and models. The durability issues addressed include the effects of short-time, cyclic, and sustained loadings; temperature; fluid environments; and low-energy impacts (e.g., tool drops and kickups of roadway debris) on deformation, strength, and stiffness. Guidance for design analysis, time-independent and time-dependent allowable stresses, rules for cyclic loadings, and damage-tolerance design guidance are provided.

  8. Designs of the frequency reference cavity for the AEI 10 m Prototype interferometer

    Science.gov (United States)

    Kawazoe, Fumiko; Taylor, John Robert; Bertolini, Alessandro; Born, Michael; Chen, Yanbei; Dahl, Katrin; Gering, Daniel; Goßler, Stefan; Gräf, Christian; Heinzel, Gerhard; Hild, Stefan; Kranz, Oliver; Kühn, Gerrit; Lück, Harald; Mossavi, Kasem; Schnabel, Roman; Somiya, Kentaro; Strain, Kenneth; Wanner, Alexander; Westphal, Tobias; Willke, Benno; Danzmann, Karsten

    2010-05-01

    The AEI 10 m Prototype is in its designing phase and will provide a test-bed for very sensitive interferometric experiments, such as the sub-SQL interferometer. It will test new techniques to reach - and even surpass - the Standard Quantum Limit. The experience and knowledge that can be gained from this experiment can be applied to large-scale interferometric gravitational detectors to improve the detector sensitivities. In order for the sub-SQL interferometer to achieve the required sensitivity all limiting noise sources need to be suppressed sufficiently. Noise sources can include seismic noise, thermal noise, and laser noise; laser frequency noise will be the main focus of this document. The laser frequency noise will be suppressed to a level of 10-4 Hz/ at 20 Hz dropping to below 10-6 Hz/ at 1kHz. The proposed design to suppress the laser frequency noise with a ring cavity is described in this paper.

  9. Test design description Volume 2, Part 1. IFR-1 metal fuel irradiation test (AK-181) element as-built data

    Energy Technology Data Exchange (ETDEWEB)

    Dodds, N. E.

    1986-06-01

    The IFR-1 Test, designated as the AK-181 Test Assembly, will be the first irradiation test of wire wrapped, sodium-bonded metallic fuel elements in the Fast Flux Test Facility (FFTF). The test is part of the Integral Fast Reactor (IFR) fuels program conducted by Argonne National Laboratory (ANL) in support of the Innovative Reactor Concepts Program sponsored by the US Department of Energy (DOE). One subassembly, containing 169 fuel elements, will be irradiated for 600 full power days to achieve 10 at.% burnup. Three metal fuel alloys (U-10Zr, U-8Pu-10Zr) will be irradiated in D9 cladding tubes. The metal fuel elements have a fuel-smeared density of 75% and each contains five slugs. The enriched zone contains three slugs and is 36-in. long. One 6.5-in. long depleted uranium axial blanket slug (DU-10Zr) was loaded at each end of the enriched zone. the fuel elements were fabricated at ANL-W and delivered to Westinghouse-Hanford for wirewrapping and assembly into the test article. This Test Design Description contains relevant data on compositions, densities, dimensions and weights for the cast fuel slugs and completed fuel elements. The elements conform to the requirements in MG-22, "Users` Guide for the Irradiation of Experiments in the FTR."

  10. The Earliest Reference to ADHD in the Medical Literature? Melchior Adam Weikard's Description in 1775 of "Attention Deficit" (Mangel der Aufmerksamkeit, Attentio Volubilis)

    Science.gov (United States)

    Barkley, Russell A.; Peters, Helmut

    2012-01-01

    Objective: The present article reports on the discovery and translation of a chapter in a 1775 medical textbook by the German physician, Melchior Adam Weikard, which describes attention disorders. This article is believed to be the earliest reference to the syndrome that today is known as attention deficit hyperactivity disorder, or ADHD. Method:…

  11. Software architecture design patterns in Java

    CERN Document Server

    Kuchana, Partha

    2004-01-01

    AN INTRODUCTION TO DESIGN PATTERNSDesign Patterns: Origin and HistoryArchitectural to Software Design PatternsWhat is a Design Pattern?More about Design PatternsAbout This BookUNIFIED MODELING LANGUAGE (UML)UML: A Quick ReferenceClass DiagramsSequence diagramsBASIC PATTERNSInterfaceDescriptionExamplePractice QuestionsAbstract Parent ClassDescriptionExamplePractice QuestionsPrivate MethodsDescriptionExamplePractice QuestionsAccessor MethodsDescriptionAccessor Method NomenclatureExampleDirect Reference versus Accessor MethodsPractice QuestionsConstant Data ManagerDescriptionExamplePractice Quest

  12. H2FIRST Reference Station Design Task: Project Deliverable 2-2

    Energy Technology Data Exchange (ETDEWEB)

    Pratt, Joseph [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Terlip, Danny [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Ainscough, Chris [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kurtz, Jennifer [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Elgowainy, Amgad [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-04-20

    This report presents near-term station cost results and discusses cost trends of different station types. It compares various vehicle rollout scenarios and projects realistic near-term station utilization values using the station infrastructure rollout in California as an example. It describes near-term market demands and matches those to cost-effective station concepts. Finally, the report contains detailed designs for five selected stations, which include piping and instrumentation diagrams, bills of materials, and several site-specific layout studies that incorporate the setbacks required by NFPA 2, the National Fire Protection Association Hydrogen Technologies Code. This work identified those setbacks as a significant factor affecting the ability to site a hydrogen station, particularly liquid stations at existing gasoline stations. For all station types, utilization has a large influence on the financial viability of the station.

  13. The Semantic Automated Discovery and Integration (SADI) Web service Design-Pattern, API and Reference Implementation.

    Science.gov (United States)

    Wilkinson, Mark D; Vandervalk, Benjamin; McCarthy, Luke

    2011-10-24

    The complexity and inter-related nature of biological data poses a difficult challenge for data and tool integration. There has been a proliferation of interoperability standards and projects over the past decade, none of which has been widely adopted by the bioinformatics community. Recent attempts have focused on the use of semantics to assist integration, and Semantic Web technologies are being welcomed by this community. SADI - Semantic Automated Discovery and Integration - is a lightweight set of fully standards-compliant Semantic Web service design patterns that simplify the publication of services of the type commonly found in bioinformatics and other scientific domains. Using Semantic Web technologies at every level of the Web services "stack", SADI services consume and produce instances of OWL Classes following a small number of very straightforward best-practices. In addition, we provide codebases that support these best-practices, and plug-in tools to popular developer and client software that dramatically simplify deployment of services by providers, and the discovery and utilization of those services by their consumers. SADI Services are fully compliant with, and utilize only foundational Web standards; are simple to create and maintain for service providers; and can be discovered and utilized in a very intuitive way by biologist end-users. In addition, the SADI design patterns significantly improve the ability of software to automatically discover appropriate services based on user-needs, and automatically chain these into complex analytical workflows. We show that, when resources are exposed through SADI, data compliant with a given ontological model can be automatically gathered, or generated, from these distributed, non-coordinating resources - a behaviour we have not observed in any other Semantic system. Finally, we show that, using SADI, data dynamically generated from Web services can be explored in a manner very similar to data housed in

  14. Gait parameters in a reference sample of healthy Spanish schoolchildren: multivariate descriptive statistics and asymmetries observed in left and right cycles.

    Science.gov (United States)

    Pulido-Valdeolivas, I; Gómez-Andrés, D; Martín-Gonzalo, J A; López-López, J; Gómez-Barrena, E; Sánchez Hernández, J J; Rausell, E

    2013-04-01

    Instrumental gait analysis is an emerging technology used increasingly to evaluate motor disorders in children. Normal reference data is necessary in order to evaluate patients, but there are few reference resources for the Spanish paediatric population. We aim to describe the values of 16 clinically relevant gait variables in healthy Spanish schoolchildren, and identify any linear associations or left-right asymmetries. The values of 16 gait variables were determined in schoolchildren (n=27, aged 5-13 years) using instrumental gait analysis. We analysed asymmetries for each variable (Student's t-test for dependent samples) and calculated their confidence intervals (95% of the standardised difference in right and left means [SMD]). Values and associations between variables were represented using a heat map. Our project presents normal values tables for 16 variables in the gait cycle. Significant asymmetries were detected in the mean values for minimum hip flexion (SMD: 0.25 95% CI, 0.11-0.39) and peak hip abduction in swing (SMD: -1.05 95% CI: -1.71--0.27). Functional associations among gait variables are present. We present a reference dataset for Spanish school-aged children in which left-right asymmetries and functional associations may be observed for different variables. Copyright © 2011 Sociedad Española de Neurología. Published by Elsevier Espana. All rights reserved.

  15. On the Design of Attitude-Heading Reference Systems Using the Allan Variance.

    Science.gov (United States)

    Hidalgo-Carrió, Javier; Arnold, Sascha; Poulakis, Pantelis

    2016-04-01

    The Allan variance is a method to characterize stochastic random processes. The technique was originally developed to characterize the stability of atomic clocks and has also been successfully applied to the characterization of inertial sensors. Inertial navigation systems (INS) can provide accurate results in a short time, which tend to rapidly degrade in longer time intervals. During the last decade, the performance of inertial sensors has significantly improved, particularly in terms of signal stability, mechanical robustness, and power consumption. The mass and volume of inertial sensors have also been significantly reduced, offering system-level design and accommodation advantages. This paper presents a complete methodology for the characterization and modeling of inertial sensors using the Allan variance, with direct application to navigation systems. Although the concept of sensor fusion is relatively straightforward, accurate characterization and sensor-information filtering is not a trivial task, yet they are essential for good performance. A complete and reproducible methodology utilizing the Allan variance, including all the intermediate steps, is described. An end-to-end (E2E) process for sensor-error characterization and modeling up to the final integration in the sensor-fusion scheme is explained in detail. The strength of this approach is demonstrated with representative tests on novel, high-grade inertial sensors. Experimental navigation results are presented from two distinct robotic applications: a planetary exploration rover prototype and an autonomous underwater vehicle (AUV).

  16. Design and performance of an arcjet nuclear electric propulsion system for a mid-1990's reference mission

    Science.gov (United States)

    Deininger, William D.; Vondra, Robert J.

    1987-01-01

    The design and performance of an arcjet nuclear-electric-propulsion spacecraft, suitable for use in the Space Nuclear Power System (SNPS) reference mission, are outlined. The vehicle design was based on a 30-kW ammonia arcjet system operating at an Isp of 1050 s and an efficiency of 45 percent. The arcjet/gimbal system, power-processing unit, and propellant-feed system are described. A 100-kWe SNPS was assumed, and the spacecraft mass was baselined at 5250 kg (excluding the propellant-feed system). A radiation/arcjet efflux diagnostics package was included in the performance analysis. This spacecraft, assuming a Shuttle launch from KSC, can perform a 50-deg inclination change and reach a final orbit of 35,860 km with a 120-d trip time providing a 4-mo active load for the SNPS. Alternatively, a Titan IV launch would provide a mass margin of 120 kg to a 10,000-km, 58-deg final orbit in 74 d. This spacecraft meets the reference-mission constraint of low developmental risk, and is scalable to power levels projected for future space platforms.

  17. A Data-Driven Control Design Approach for Freeway Traffic Ramp Metering with Virtual Reference Feedback Tuning

    Directory of Open Access Journals (Sweden)

    Shangtai Jin

    2014-01-01

    Full Text Available ALINEA is a simple, efficient, and easily implemented ramp metering strategy. Virtual reference feedback tuning (VRFT is most suitable for many practical systems since it is a “one-shot” data-driven control design methodology. This paper presents an application of VRFT to a ramp metering problem of freeway traffic system. When there is not enough prior knowledge of the controlled system to select a proper parameter of ALINEA, the VRFT approach is used to optimize the ALINEA's parameter by only using a batch of input and output data collected from the freeway traffic system. The extensive simulations are built on both the macroscopic MATLAB platform and the microscopic PARAMICS platform to show the effectiveness and applicability of the proposed data-driven controller tuning approach.

  18. Interreligious education: Conceptualising a needs assessment framework for curriculum design in plural societies (with special reference to Mauritius)

    Science.gov (United States)

    Maudarbux, Mohammad Belall

    2016-08-01

    The growing debate on intercultural and interreligious dialogue has one major drawback: how to translate academic and theoretical contributions into practical tools for educators and policy makers. This paper aims to fill this gap by presenting a transferable "needs assessment model" based on five criteria and twenty measurable indicators of interreligious relations within a country. Using the example of Mauritius, a densely multilingual and multireligious country, the paper gives an inside view of the preparations which led to the launch of an innovative "Peace and Interfaith Studies" course at the University of Mauritius in 2010. The author was himself involved first as a curriculum consultant and then as a project manager of this course at the Council of Religions in Mauritius. After clarifying the differences between related concepts like multicultural education, intercultural education and religious education, the author defines "interreligious education" as being distinct from all of the above. The paper then proceeds to explain the rationale of interreligious education, followed by the identification of the critical factors which affect curriculum design and policy making. It uses these factors to highlight how each of them operates in Mauritius to create a web of complexity which makes interreligious education extremely volatile. This is followed by an overview of religious education in the Mauritian schooling system, an overview of the needs assessment framework and a description of the innovative "Peace and Interfaith Studies" course. The paper ends with a brief discussion of the main challenges of this model.

  19. BABAR: an R package to simplify the normalisation of common reference design microarray-based transcriptomic datasets

    Directory of Open Access Journals (Sweden)

    Hinton Jay CD

    2010-02-01

    Full Text Available Abstract Background The development of DNA microarrays has facilitated the generation of hundreds of thousands of transcriptomic datasets. The use of a common reference microarray design allows existing transcriptomic data to be readily compared and re-analysed in the light of new data, and the combination of this design with large datasets is ideal for 'systems'-level analyses. One issue is that these datasets are typically collected over many years and may be heterogeneous in nature, containing different microarray file formats and gene array layouts, dye-swaps, and showing varying scales of log2- ratios of expression between microarrays. Excellent software exists for the normalisation and analysis of microarray data but many data have yet to be analysed as existing methods struggle with heterogeneous datasets; options include normalising microarrays on an individual or experimental group basis. Our solution was to develop the Batch Anti-Banana Algorithm in R (BABAR algorithm and software package which uses cyclic loess to normalise across the complete dataset. We have already used BABAR to analyse the function of Salmonella genes involved in the process of infection of mammalian cells. Results The only input required by BABAR is unprocessed GenePix or BlueFuse microarray data files. BABAR provides a combination of 'within' and 'between' microarray normalisation steps and diagnostic boxplots. When applied to a real heterogeneous dataset, BABAR normalised the dataset to produce a comparable scaling between the microarrays, with the microarray data in excellent agreement with RT-PCR analysis. When applied to a real non-heterogeneous dataset and a simulated dataset, BABAR's performance in identifying differentially expressed genes showed some benefits over standard techniques. Conclusions BABAR is an easy-to-use software tool, simplifying the simultaneous normalisation of heterogeneous two-colour common reference design cDNA microarray

  20. BABAR: an R package to simplify the normalisation of common reference design microarray-based transcriptomic datasets.

    Science.gov (United States)

    Alston, Mark J; Seers, John; Hinton, Jay C D; Lucchini, Sacha

    2010-02-03

    The development of DNA microarrays has facilitated the generation of hundreds of thousands of transcriptomic datasets. The use of a common reference microarray design allows existing transcriptomic data to be readily compared and re-analysed in the light of new data, and the combination of this design with large datasets is ideal for 'systems'-level analyses. One issue is that these datasets are typically collected over many years and may be heterogeneous in nature, containing different microarray file formats and gene array layouts, dye-swaps, and showing varying scales of log2- ratios of expression between microarrays. Excellent software exists for the normalisation and analysis of microarray data but many data have yet to be analysed as existing methods struggle with heterogeneous datasets; options include normalising microarrays on an individual or experimental group basis. Our solution was to develop the Batch Anti-Banana Algorithm in R (BABAR) algorithm and software package which uses cyclic loess to normalise across the complete dataset. We have already used BABAR to analyse the function of Salmonella genes involved in the process of infection of mammalian cells. The only input required by BABAR is unprocessed GenePix or BlueFuse microarray data files. BABAR provides a combination of 'within' and 'between' microarray normalisation steps and diagnostic boxplots. When applied to a real heterogeneous dataset, BABAR normalised the dataset to produce a comparable scaling between the microarrays, with the microarray data in excellent agreement with RT-PCR analysis. When applied to a real non-heterogeneous dataset and a simulated dataset, BABAR's performance in identifying differentially expressed genes showed some benefits over standard techniques. BABAR is an easy-to-use software tool, simplifying the simultaneous normalisation of heterogeneous two-colour common reference design cDNA microarray-based transcriptomic datasets. We show BABAR transforms real and

  1. HMI-Design of System Solutions in Control Rooms. Description of a Working Process from a Human-Machine Perspective; MMI-design av systemloesningar i kontrollrum. Arbetsprocess foer utformning utifraan ett maenniska-maskinperspektiv

    Energy Technology Data Exchange (ETDEWEB)

    Bligaard, Lars-Ola; Andersson, Jonas; Thunberg, Anna; Osvalder, Anna-Lisa

    2008-01-15

    between operators and machines. The content can be used both for new development projects and for upgrading of already existing control room designs. The main target group for the report is the development engineers at the plant, who work close to the supplier, and the people who should plan and guide the development work in the control room. The purpose of the report is to deliver knowledge about how to consider a human-machine perspective in the development process. The report presents what is important to consider, but does not in detail show design solutions. The report is also a usable tool for those people who should do the actual screen designs, but then it should be used together with hand-book data and guide-lines referred to. The report begins with a description of basic concepts and definitions within the area of HMI. This is followed by a description of the HMI development working process. The working process includes five steps; planning, requirements, conceptual design, detailed design, and commissioning. The steps also include methodology for data collection and evaluation. Finally, the handbook also contains short summaries of the different steps in the working process, where important points to consider are brought forward

  2. Development of certified reference material of mineral composition of natural water designed to control of turbidity measurement accuracy

    Directory of Open Access Journals (Sweden)

    Liudmila I. Gorjaeva

    2017-01-01

    Full Text Available Introduction. The results of development of a certified reference material (CRM of mineral composition of natural water are presented. A solution prepared from the material of the CRM specimen imitates mineral composition of natural surface water. The certified values are mass fractions of nitrate ions, chloride ions, fluoride ions, and total iron and turbidity according to formazine scale. Materials and methods. The certified values of mass concentrations of the components were determined using calculated experimental evaluation procedure;the certified turbidity value was determinedusing the certified turbidimetric method. Results. The relative expanded uncertainty (k = 2 of the certified turbidity values does not exceed 5 %, the same value for mass concentrationsis not more than 3.5 %. Relative standard uncertainty from heterogeneity does not exceed 1.0 %. The shelf life of the developed CRM is set to 3 years. Discussion and conclusion. Developed CRM was registered in the State Register of CRM's as GSO 10815-2016. The CRM is designed to control the accuracy of results of the certified characteristics measurements, including proficiency testing of laboratories using interlaboratory comparative tests. The CRM can be used for validation of measurement procedures.

  3. Benefits of statistical molecular design, covariance analysis, and reference models in QSAR: a case study on acetylcholinesterase.

    Science.gov (United States)

    Andersson, C David; Hillgren, J Mikael; Lindgren, Cecilia; Qian, Weixing; Akfur, Christine; Berg, Lotta; Ekström, Fredrik; Linusson, Anna

    2015-03-01

    Scientific disciplines such as medicinal- and environmental chemistry, pharmacology, and toxicology deal with the questions related to the effects small organic compounds exhort on biological targets and the compounds' physicochemical properties responsible for these effects. A common strategy in this endeavor is to establish structure-activity relationships (SARs). The aim of this work was to illustrate benefits of performing a statistical molecular design (SMD) and proper statistical analysis of the molecules' properties before SAR and quantitative structure-activity relationship (QSAR) analysis. Our SMD followed by synthesis yielded a set of inhibitors of the enzyme acetylcholinesterase (AChE) that had very few inherent dependencies between the substructures in the molecules. If such dependencies exist, they cause severe errors in SAR interpretation and predictions by QSAR-models, and leave a set of molecules less suitable for future decision-making. In our study, SAR- and QSAR models could show which molecular sub-structures and physicochemical features that were advantageous for the AChE inhibition. Finally, the QSAR model was used for the prediction of the inhibition of AChE by an external prediction set of molecules. The accuracy of these predictions was asserted by statistical significance tests and by comparisons to simple but relevant reference models.

  4. A Lectotype Designation and Description for Anopheles (An.) sinensis Wiedemann 1828, with a Discussion of the Classification and Vector Status of This and Some Other Oriental Anopheles

    Science.gov (United States)

    1973-01-01

    Ward. 1970. Plasmodium cynomolgi: Sources of variation in susceptibility of Anopheles quadrimaculatus , A balabacensis and A. stephensi. 2 Exp...VOL. S(7) 7973 A Lectotype Designation and Description for Anopheles (An.) sinensis Wiedemann 1828, with a Discussion ofxe Classification and...Vector Status of This and Some Other Oriental Anopheles BY Bruce A. Harrison, CPT, MSC Department of Entomology Walter Reed Army Institute of

  5. New SCALE Sensitivity/Uncertainty Capabilities Applied to Bias Estimation and to Design of MIRTE Reference Experiments

    Energy Technology Data Exchange (ETDEWEB)

    Rearden, Bradley T [ORNL; Duhamel, Isabelle [Institut de Radioprotection et de Surete Nucleaire; Letang, Eric [Institut de Radioprotection et de Surete Nucleaire

    2009-01-01

    New TSUNAMI tools of SCALE 6, TSURFER and TSAR, are demonstrated to examine the bias effects of small-worth test materials, relative to reference experiments. TSURFER is a data adjustment bias and bias uncertainty assessment tool, and TSAR computes the sensitivity of the change in reactivity between two systems to the cross-section data common to their calculation. With TSURFER, it is possible to examine biases and bias uncertainties in fine detail. For replacement experiments, the application of TSAR to TSUNAMI-3D sensitivity data for pairs of experiments allows the isolation of sources of bias that could otherwise be obscured by materials with more worth in an individual experiment. The application of TSUNAMI techniques in the design of nine reference experiments for the MIRTE program will allow application of these advanced techniques to data acquired in the experimental series. The validation of all materials in a complex criticality safety application likely requires consolidating information from many different critical experiments. For certain materials, such as structural materials or fission products, only a limited number of critical experiments are available, and the fuel and moderator compositions of the experiments may differ significantly from those of the application. In these cases, it is desirable to extract the computational bias of a specific material from an integral keff measurement and use that information to quantify the bias due to the use of the same material in the application system. Traditional parametric and nonparametric methods are likely to prove poorly suited for such a consolidation of specific data components from a diverse set of experiments. An alternative choice for consolidating specific data from numerous sources is a data adjustment tool, like the ORNL tool TSURFER (Tool for Sensitivity/Uncertainty analysis of Response Functionals using Experimental Results) from SCALE 6.1 However, even with TSURFER, it may be difficult to

  6. Using the template for intervention description and replication (TIDieR) as a tool for improving the design and reporting of manual therapy interventions.

    Science.gov (United States)

    Alvarez, Gerard; Cerritelli, Francesco; Urrutia, Gerard

    2016-08-01

    The detailed reporting of any research intervention is crucial to evaluate its applicability into a routinely practice-based context. However, it has been estimated that, especially in non-pharmacological interventions, the published literature typically includes incomplete intervention details. In the field of manual medicine, where interventions are delivered with a high degree of individualization and variability, poorly reported studies could compromise internal and external validity of the results. Among the various initiatives that have been undertaken to improve the intervention description, the Template for Intervention Description and Replication (TIDieR) has to be highlighted as the most promising. TIDieR offers both to researchers and clinicians a helpful and comprehensive guidance on how manual therapy interventions have to be designed and reported, taking into account the clinical complexity of manual therapy and the need to satisfy research gold standards. Copyright © 2016 Elsevier Ltd. All rights reserved.

  7. A novel strategy for selection and validation of reference genes in dynamic multidimensional experimental design in yeast.

    Directory of Open Access Journals (Sweden)

    Ayca Cankorur-Cetinkaya

    Full Text Available BACKGROUND: Understanding the dynamic mechanism behind the transcriptional organization of genes in response to varying environmental conditions requires time-dependent data. The dynamic transcriptional response obtained by real-time RT-qPCR experiments could only be correctly interpreted if suitable reference genes are used in the analysis. The lack of available studies on the identification of candidate reference genes in dynamic gene expression studies necessitates the identification and the verification of a suitable gene set for the analysis of transient gene expression response. PRINCIPAL FINDINGS: In this study, a candidate reference gene set for RT-qPCR analysis of dynamic transcriptional changes in Saccharomyces cerevisiae was determined using 31 different publicly available time series transcriptome datasets. Ten of the twelve candidates (TPI1, FBA1, CCW12, CDC19, ADH1, PGK1, GCN4, PDC1, RPS26A and ARF1 we identified were not previously reported as potential reference genes. Our method also identified the commonly used reference genes ACT1 and TDH3. The most stable reference genes from this pool were determined as TPI1, FBA1, CDC19 and ACT1 in response to a perturbation in the amount of available glucose and as FBA1, TDH3, CCW12 and ACT1 in response to a perturbation in the amount of available ammonium. The use of these newly proposed gene sets outperformed the use of common reference genes in the determination of dynamic transcriptional response of the target genes, HAP4 and MEP2, in response to relaxation from glucose and ammonium limitations, respectively. CONCLUSIONS: A candidate reference gene set to be used in dynamic real-time RT-qPCR expression profiling in yeast was proposed for the first time in the present study. Suitable pools of stable reference genes to be used under different experimental conditions could be selected from this candidate set in order to successfully determine the expression profiles for the genes of

  8. Safety assessment in plant layout design using indexing approach: implementing inherent safety perspective. Part 1 - guideword applicability and method description.

    Science.gov (United States)

    Tugnoli, Alessandro; Khan, Faisal; Amyotte, Paul; Cozzani, Valerio

    2008-12-15

    Layout planning plays a key role in the inherent safety performance of process plants since this design feature controls the possibility of accidental chain-events and the magnitude of possible consequences. A lack of suitable methods to promote the effective implementation of inherent safety in layout design calls for the development of new techniques and methods. In the present paper, a safety assessment approach suitable for layout design in the critical early phase is proposed. The concept of inherent safety is implemented within this safety assessment; the approach is based on an integrated assessment of inherent safety guideword applicability within the constraints typically present in layout design. Application of these guidewords is evaluated along with unit hazards and control devices to quantitatively map the safety performance of different layout options. Moreover, the economic aspects related to safety and inherent safety are evaluated by the method. Specific sub-indices are developed within the integrated safety assessment system to analyze and quantify the hazard related to domino effects. The proposed approach is quick in application, auditable and shares a common framework applicable in other phases of the design lifecycle (e.g. process design). The present work is divided in two parts: Part 1 (current paper) presents the application of inherent safety guidelines in layout design and the index method for safety assessment; Part 2 (accompanying paper) describes the domino hazard sub-index and demonstrates the proposed approach with a case study, thus evidencing the introduction of inherent safety features in layout design.

  9. Computer software design description for the Treated Effluent Disposal Facility (TEDF), Project L-045H, Operator Training Station (OTS)

    Energy Technology Data Exchange (ETDEWEB)

    Carter, R.L. Jr.

    1994-11-07

    The Treated Effluent Disposal Facility (TEDF) Operator Training Station (OTS) is a computer-based training tool designed to aid plant operations and engineering staff in familiarizing themselves with the TEDF Central Control System (CCS).

  10. Ontology Language to Support Description of Experiment Control System Semantics, Collaborative Knowledge-Base Design and Ontology Reuse

    Energy Technology Data Exchange (ETDEWEB)

    Vardan Gyurjyan, D Abbott, G Heyes, E Jastrzembski, B Moffit, C Timmer, E Wolin

    2009-10-01

    In this paper we discuss the control domain specific ontology that is built on top of the domain-neutral Resource Definition Framework (RDF). Specifically, we will discuss the relevant set of ontology concepts along with the relationships among them in order to describe experiment control components and generic event-based state machines. Control Oriented Ontology Language (COOL) is a meta-data modeling language that provides generic means for representation of physics experiment control processes and components, and their relationships, rules and axioms. It provides a semantic reference frame that is useful for automating the communication of information for configuration, deployment and operation. COOL has been successfully used to develop a complete and dynamic knowledge-base for experiment control systems, developed using the AFECS framework.

  11. Analysis, Design, and Experimental Verification of A Synchronous Reference Frame Voltage Control for Single-Phase Inverters

    DEFF Research Database (Denmark)

    Monfared, Mohammad; Golestan, Saeed; Guerrero, Josep M.

    2014-01-01

    -loop control strategy for single phase inverter-based islanded distributed generation (DG) systems. The proposed controller uses a synchronous reference frame PI (SRFPI) controller to regulate the instantaneous output voltage, a capacitor current shaping loop in the stationary reference frame to provide active...... damping and improve both transient and steady-state performances, a voltage decoupling feedforward to improve the system robustness, and a multi-resonant harmonic compensator to prevent low-order load current harmonics to distort the inverter output voltage. Since, the voltage loop works...

  12. Design and Development of an Equipotential Voltage Reference (Grounding) System for a Low-Cost Rapid-Development Modular Spacecraft Architecture

    Science.gov (United States)

    Lukash, James A.; Daley, Earl

    2011-01-01

    This work describes the design and development effort to adapt rapid-development space hardware by creating a ground system using solutions of low complexity, mass, & cost. The Lunar Atmosphere and Dust Environment Explorer (LADEE) spacecraft is based on the modular common spacecraft bus architecture developed at NASA Ames Research Center. The challenge was building upon the existing modular common bus design and development work and improving the LADEE spacecraft design by adding an Equipotential Voltage Reference (EVeR) system, commonly referred to as a ground system. This would aid LADEE in meeting Electromagnetic Environmental Effects (E3) requirements, thereby making the spacecraft more compatible with itself and its space environment. The methods used to adapt existing hardware are presented, including provisions which may be used on future spacecraft.

  13. Plot Description (PD)

    Science.gov (United States)

    Robert E. Keane

    2006-01-01

    The Plot Description (PD) form is used to describe general characteristics of the FIREMON macroplot to provide ecological context for data analyses. The PD data characterize the topographical setting, geographic reference point, general plant composition and cover, ground cover, fuels, and soils information. This method provides the general ecological data that can be...

  14. Social Skills Interventions for Preschoolers with Autism Spectrum Disorder: A Description of Single-Subject Design Studies

    Science.gov (United States)

    Gillis, Jennifer M.; Butler, Robert C.

    2007-01-01

    Social skill development is one of the primary areas of intervention for young children with Autism Spectrum Disorders (ASD). The purpose of this article was to conduct a retrospective review of social skills intervention research for preschool children with ASD. A review of 17 single-subject design studies from twelve journals (1999-2006) was…

  15. Design of high-resolution and multilevel reference pattern for improvement of both light utilization efficiency and signal-to-noise ratio in coaxial holographic data storage.

    Science.gov (United States)

    Nobukawa, Teruyoshi; Nomura, Takanori

    2014-06-10

    A high-resolution and multilevel designed reference pattern (DRP) is presented for improvement of both light utilization efficiency and the signal-to-noise ratio (SNR) of reconstructed images in coaxial holographic data storage. With a DRP, the desired Fourier power spectrum of a reference beam is obtained. Numerical and experimental results show that the DRP increases the SNR compared with that of a random phase mask (RPM). Moreover, the light utilization efficiency of the DRP is higher than that of a high-resolution RPM. In addition, the effect of the phase level and the pixel pitch of DRPs on the SNR and the light utilization efficiency are investigated.

  16. A descriptive study of the barriers to study abroad in engineering undergraduate education and recommendations for program design

    Science.gov (United States)

    Klahr, Sabine Christine

    This study analyzed and compared the program designs of international exchange and internship programs for engineering students in the United States and the European Union (E.U.) as well as the extent to which these programs have removed barriers to study abroad. The purpose of this study was to provide recommendations for the design of international programs in the U.S. that would increase the proportion of engineering students who choose to study or intern abroad. Coordinators of international programs in engineering were surveyed about their perceptions of program success and a number of variables related to program design. A Chi-Square Test of Independence of (A) program success and (B) European and U.S. programs (i.e. institution location) cross-tabulated with all other variables and each other indicated those variables that contribute to the success of programs and those variables that are associated with either U.S. or European programs. In addition, all programs were described and the answers to open-ended survey questions were analyzed quantitatively. The analyses indicated that European programs tend to be more successful in implementing study/intern abroad programs for engineering students than U.S. programs. The elements of program design contributing to the greater success of European programs and the success of specific U.S. programs were described. In addition, the characteristics of overall successful programs (U.S. and E.U. data combined) were explained. The results indicated that successful programs tend to: (1) be promoted by the college and/or departments of engineering, (2) offer study/intern abroad opportunities in English-speaking settings, (3) award full credit at the home institution for required engineering courses completed at the host institution, (4) offer scholarships and financial aid for participation in the program, (5) require participating students to have completed their second year of university course work prior to applying to

  17. Descriptive Research

    DEFF Research Database (Denmark)

    Wigram, Anthony Lewis

    2003-01-01

    starts will allow effect size calculations to be made in order to evaluate effect over time. Given the difficulties in undertaking controlled experimental studies in the creative arts therapies, descriptive research methods offer a way of quantifying effect through descriptive statistical analysis...

  18. System design description of forced-convection molten-salt corrosion loops MSR-FCL-3 and MSR-FCL-4

    Energy Technology Data Exchange (ETDEWEB)

    Huntley, W.R.; Silverman, M.D.

    1976-11-01

    Molten-salt corrosion loops MSR-FCL-3 and MSR-FCL-4 are high-temperature test facilities designed to evaluate corrosion and mass transfer of modified Hastelloy N alloys for future use in Molten-Salt Breeder Reactors. Salt is circulated by a centrifugal sump pump to evaluate material compatibility with LiF-BeF/sub 2/-ThF/sub 4/-UF/sub 4/ fuel salt at velocities up to 6 m/s (20 fps) and at salt temperatures from 566 to 705/sup 0/C (1050 to 1300/sup 0/F). The report presents the design description of the various components and systems that make up each corrosion facility, such as the salt pump, corrosion specimens, salt piping, main heaters, salt coolers, salt sampling equipment, and helium cover-gas system, etc. The electrical systems and instrumentation and controls are described, and operational procedures, system limitations, and maintenance philosophy are discussed.

  19. System Design Description for the SY-101 Hydrogen Mitigation Test Project Data Acquisition and Control System (DACS-1)

    Energy Technology Data Exchange (ETDEWEB)

    ERMI, A.M.

    1999-08-25

    This document describes the hardware and software of the computer subsystems for the Data Acquisition and Control System (DACS) used in mitigation tests conducted on waste tank 241-SY-101 at the Hanford Nuclear Reservation, The original system was designed and implemented by LANL, supplied to WHC, and turned over to LMHC for operation. In 1999, the hardware and software were upgraded to provide a state-of-the-art, Year-2000 compliant system.

  20. Test Design Description: Volume 2, Part 1, MFF-1 and MFF-1A metal fuel irradiations (HF168 and HF169) element as-built data

    Energy Technology Data Exchange (ETDEWEB)

    Dodds, N. E.

    1987-06-01

    The metal fuel in FFTF (MFF) tests represented by the Test Design Description (TDD), Volume II, Part I will be the second irradiation test of full length Integral Fast Reactor (IFR) fuel elements in FFTF. The MFF-1 Test, designated as the HF168 Test Assembly, will contain six sodium-bonded metallic fuel elements clad in HT9 interspersed in a basically oxide fuel assembly. The wire-wrapped elements will be irradiated to breach or 900 EFPD with peak nominal cladding temperatures of 1127{sup 0}F. The MFF-1A test, designated as the HF169 Test assembly, will also contain six sodium-bonded metallic fuel elements clad in HT9 interspersed in an oxide fuel assembly. The MFF-1A elements will be irradiated at a peak nominal cladding temperature of 1127{sup 0}F to 450 EFPD or until a cladding breach occurs. The metal fuel elements contain U-10Zr cast slugs and have a fuel-smeared density of 75%. The enriched zone is 36-in. long, composed of three slugs and has one 6.5-in. long depleted-uranium axial blanket slug (DU-10Zr) at each end. The metal fuel elements were fabricated at ANL-W and delivered to Westinghouse-Hanford for assembly into the test article. This Test Design Description contains only the relevant fabrication data for the metal fuel elements built at Argonne. The elements conform to the requirements in MG-22, "User`s Guide for the Irradiation of Experiments in the FTR."

  1. Designation and description of a neotype of Sclerophrys maculata (Hallowell, 1854), and reinstatement of S. pusilla (Mertens, 1937) (Amphibia: Anura: Bufonidae).

    Science.gov (United States)

    Poynton, John C; Loader, Simon P; Conradie, Werner; Rödel, Mark-Oliver; Liedtke, H Christoph

    2016-04-05

    Molecular analysis indicates that African material previously referred to Amietophrynus maculatus (Hallowell, 1854; now Sclerophrys maculata), is divisible into two distinct clades: a Western Clade from Cameroon westwards and an Eastern Clade from Central African Republic eastwards, and Uganda southwards to South Africa, extending to Angola-Namibia. Preliminary morphological and bioacoustic data support this division. The two clades are recognised here as two separate species. The Western species retains the name S. maculata, with Hallowell's designated type locality of Liberia. The Eastern Clade retains the name published by Mertens (1937), S. pusilla. It is noted that a type specimen of S. maculata cannot be traced and is presumed lost; the so-called syntypes in the Philadelphia Academy of Natural Sciences are not the material described by Hallowell. None of these have been designated as a neotype, consequently a specimen from Liberia in the collection of the Natural History Museum, London, is designated here as the neotype of S. maculata.

  2. A Brief Description of High Temperature Solid Oxide Fuel Cell’s Operation, Materials, Design, Fabrication Technologies and Performance

    Directory of Open Access Journals (Sweden)

    Muneeb Irshad

    2016-03-01

    Full Text Available Today’s world needs highly efficient systems that can fulfill the growing demand for energy. One of the promising solutions is the fuel cell. Solid oxide fuel cell (SOFC is considered by many developed countries as an alternative solution of energy in near future. A lot of efforts have been made during last decade to make it commercial by reducing its cost and increasing its durability. Different materials, designs and fabrication technologies have been developed and tested to make it more cost effective and stable. This article is focused on the advancements made in the field of high temperature SOFC. High temperature SOFC does not need any precious catalyst for its operation, unlike in other types of fuel cell. Different conventional and innovative materials have been discussed along with properties and effects on the performance of SOFC’s components (electrolyte anode, cathode, interconnect and sealing materials. Advancements made in the field of cell and stack design are also explored along with hurdles coming in their fabrication and performance. This article also gives an overview of methods required for the fabrication of different components of SOFC. The flexibility of SOFC in terms fuel has also been discussed. Performance of the SOFC with varying combination of electrolyte, anode, cathode and fuel is also described in this article.

  3. Evidence-based design and evaluation of a whole genome sequencing clinical report for the reference microbiology laboratory

    Directory of Open Access Journals (Sweden)

    Anamaria Crisan

    2018-01-01

    Full Text Available Background Microbial genome sequencing is now being routinely used in many clinical and public health laboratories. Understanding how to report complex genomic test results to stakeholders who may have varying familiarity with genomics—including clinicians, laboratorians, epidemiologists, and researchers—is critical to the successful and sustainable implementation of this new technology; however, there are no evidence-based guidelines for designing such a report in the pathogen genomics domain. Here, we describe an iterative, human-centered approach to creating a report template for communicating tuberculosis (TB genomic test results. Methods We used Design Study Methodology—a human centered approach drawn from the information visualization domain—to redesign an existing clinical report. We used expert consults and an online questionnaire to discover various stakeholders’ needs around the types of data and tasks related to TB that they encounter in their daily workflow. We also evaluated their perceptions of and familiarity with genomic data, as well as its utility at various clinical decision points. These data shaped the design of multiple prototype reports that were compared against the existing report through a second online survey, with the resulting qualitative and quantitative data informing the final, redesigned, report. Results We recruited 78 participants, 65 of whom were clinicians, nurses, laboratorians, researchers, and epidemiologists involved in TB diagnosis, treatment, and/or surveillance. Our first survey indicated that participants were largely enthusiastic about genomic data, with the majority agreeing on its utility for certain TB diagnosis and treatment tasks and many reporting some confidence in their ability to interpret this type of data (between 58.8% and 94.1%, depending on the specific data type. When we compared our four prototype reports against the existing design, we found that for the majority (86.7% of

  4. Evidence-based design and evaluation of a whole genome sequencing clinical report for the reference microbiology laboratory.

    Science.gov (United States)

    Crisan, Anamaria; McKee, Geoffrey; Munzner, Tamara; Gardy, Jennifer L

    2018-01-01

    Microbial genome sequencing is now being routinely used in many clinical and public health laboratories. Understanding how to report complex genomic test results to stakeholders who may have varying familiarity with genomics-including clinicians, laboratorians, epidemiologists, and researchers-is critical to the successful and sustainable implementation of this new technology; however, there are no evidence-based guidelines for designing such a report in the pathogen genomics domain. Here, we describe an iterative, human-centered approach to creating a report template for communicating tuberculosis (TB) genomic test results. We used Design Study Methodology-a human centered approach drawn from the information visualization domain-to redesign an existing clinical report. We used expert consults and an online questionnaire to discover various stakeholders' needs around the types of data and tasks related to TB that they encounter in their daily workflow. We also evaluated their perceptions of and familiarity with genomic data, as well as its utility at various clinical decision points. These data shaped the design of multiple prototype reports that were compared against the existing report through a second online survey, with the resulting qualitative and quantitative data informing the final, redesigned, report. We recruited 78 participants, 65 of whom were clinicians, nurses, laboratorians, researchers, and epidemiologists involved in TB diagnosis, treatment, and/or surveillance. Our first survey indicated that participants were largely enthusiastic about genomic data, with the majority agreeing on its utility for certain TB diagnosis and treatment tasks and many reporting some confidence in their ability to interpret this type of data (between 58.8% and 94.1%, depending on the specific data type). When we compared our four prototype reports against the existing design, we found that for the majority (86.7%) of design comparisons, participants preferred the

  5. Evidence-based design and evaluation of a whole genome sequencing clinical report for the reference microbiology laboratory

    Science.gov (United States)

    Crisan, Anamaria; McKee, Geoffrey; Munzner, Tamara

    2018-01-01

    Background Microbial genome sequencing is now being routinely used in many clinical and public health laboratories. Understanding how to report complex genomic test results to stakeholders who may have varying familiarity with genomics—including clinicians, laboratorians, epidemiologists, and researchers—is critical to the successful and sustainable implementation of this new technology; however, there are no evidence-based guidelines for designing such a report in the pathogen genomics domain. Here, we describe an iterative, human-centered approach to creating a report template for communicating tuberculosis (TB) genomic test results. Methods We used Design Study Methodology—a human centered approach drawn from the information visualization domain—to redesign an existing clinical report. We used expert consults and an online questionnaire to discover various stakeholders’ needs around the types of data and tasks related to TB that they encounter in their daily workflow. We also evaluated their perceptions of and familiarity with genomic data, as well as its utility at various clinical decision points. These data shaped the design of multiple prototype reports that were compared against the existing report through a second online survey, with the resulting qualitative and quantitative data informing the final, redesigned, report. Results We recruited 78 participants, 65 of whom were clinicians, nurses, laboratorians, researchers, and epidemiologists involved in TB diagnosis, treatment, and/or surveillance. Our first survey indicated that participants were largely enthusiastic about genomic data, with the majority agreeing on its utility for certain TB diagnosis and treatment tasks and many reporting some confidence in their ability to interpret this type of data (between 58.8% and 94.1%, depending on the specific data type). When we compared our four prototype reports against the existing design, we found that for the majority (86.7%) of design

  6. System-Level Shared Governance Structures and Processes in Healthcare Systems With Magnet®-Designated Hospitals: A Descriptive Study.

    Science.gov (United States)

    Underwood, Carlisa M; Hayne, Arlene N

    The purpose was to identify and describe structures and processes of best practices for system-level shared governance in healthcare systems. Currently, more than 64.6% of US community hospitals are part of a system. System chief nurse executives (SCNEs) are challenged to establish leadership structures and processes that effectively and efficiently disseminate best practices for patients and staff across complex organizations, geographically dispersed locations, and populations. Eleven US healthcare SCNEs from the American Nurses Credentialing Center's repository of Magnet®-designated facilities participated in a 35-multiquestion interview based on Kanter's Theory of Organizational Empowerment. Most SCNEs reported the presence of more than 50% of the empowerment structures and processes in system-level shared governance. Despite the difficulties and complexities of growing health systems, SCNEs have replicated empowerment characteristics of hospital shared governance structures and processes at the system level.

  7. Energy Economic Data Base (EEDB) Program. Technical Reference Book

    Energy Technology Data Exchange (ETDEWEB)

    Allen, R.E.; Benedict, R.G.; Hodson, J.S.

    1983-09-01

    Purpose of the program is to develop current technical and cost information for nuclear and comparison electric power generating stations. Purpose of this Technical Reference Book is to provide the current technical design bases for each of the technical data models updated in the Sixth Update (1983). It contains a set of detailed system design descriptions for these technical data models, which are supplemented with engineering drawings. The system design descriptions reflect regulatory and industry practice and experience for nuclear and coal-fired power generating stations that are current for January 1, 1983.

  8. Engineering manual. A practical reference of design methods and data in building systems, chemical, civil, electrical, mechanical, and environmental engineering and energy conversion

    Energy Technology Data Exchange (ETDEWEB)

    Perry, R.H. (ed.)

    1976-01-01

    Following 3 chapters of general reference information for engineers which include mathematics and mathematical tables, heat transfer, fluid flow, and basic thermodynamics, and data on the chemical, mechanical, and physical properties of materials, 7 chapters of data and design methods for specific engineering fields, i.e., architectural or building systems, chemical, civil, electrical, mechanical, environmental, and for energy conversion are presented. A subject index is included. (LCL)

  9. An appraisal of digital reference services in Nigerian university ...

    African Journals Online (AJOL)

    This study examined digital reference services in Nigeria university libraries. A descriptive research design of the ex -post facto was adopted in the study. The instrument used in collecting data for this study was the questionnaire. One hundred and twenty respondents were randomly selected from six Nigerian universities ...

  10. An Appraisal of Digital Reference Services in Nigerian University ...

    African Journals Online (AJOL)

    This study examined digital reference services in Nigeria university libraries. A descriptive research design of the ex-post facto was adopted in the study. The instrument used in collecting data for this study was the questionnaire. One hundred and twenty respondents were randomly selected from six Nigerian universities ...

  11. Establishment of Adult Reference Values For Some Biochemical ...

    African Journals Online (AJOL)

    Objectives: To establish the reference values for some routinely performed biochemical analytes in CHUK. Design: Cross-sectional descriptive study. Settings: National Center for Blood Transfusion, Rwanda and Kigali University Teaching Hospital, Laboratory Department. This study was conducted during the period ...

  12. Descriptive statistics.

    Science.gov (United States)

    Shi, Runhua; McLarty, Jerry W

    2009-10-01

    In this article, we introduced basic concepts of statistics, type of distributions, and descriptive statistics. A few examples were also provided. The basic concepts presented herein are only a fraction of the concepts related to descriptive statistics. Also, there are many commonly used distributions not presented herein, such as Poisson distributions for rare events and exponential distributions, F distributions, and logistic distributions. More information can be found in many statistics books and publications.

  13. Design and descriptive results of the "Growth, Exercise and Nutrition Epidemiological Study In preSchoolers": The GENESIS Study

    Directory of Open Access Journals (Sweden)

    Manios Yannis

    2006-02-01

    Full Text Available Abstract Background The Growth, Exercise and Nutrition Epidemiological Study in preSchoolers (GENESIS attempts to evaluate the food and nutrient intakes, as well as growth and development of a representative sample of Greek toddlers and preschool children. In the current work the study design, data collection procedures and some preliminary data of the GENESIS study are presented. Methods From April 2003 to July 2004, 1218 males and 1156 females 1 to 5 years old, stratified by parental educational level (Census 1999, were examined from 105 nurseries in five counties. Approximately 300 demographic, lifestyle, physical activity, dietary, anthropometrical and DNA variables have been recorded from the study population (children and parents. Results Regarding anthropometrical indices, boys were found to be taller than girls at all ages (P Conclusion The prevalence of overweight in the current preschool population is considerably high. Future but more extensive analyses of the GENESIS data will be able to reveal the interactions of the parameters leading to this phenomenon.

  14. System design description for SY-101 hydrogen mitigation test project data acquisition and control system (DACS-1)

    Energy Technology Data Exchange (ETDEWEB)

    Truitt, R.W. [Westinghouse Hanford Co., Richland, WA (United States); Pounds, T.S.; Smith, S.O. [EG and G Energy Measurements, Inc., Las Vegas, NV (United States)

    1994-08-24

    This document describes the hardware subsystems of the data acquisition and control system (DACS) used in mitigation tests conducted on waste tank SY-101 at the Hanford Nuclear Reservation. The system was designed and implemented by Los Alamos National Laboratory (LANL) and supplied to Westinghouse Hanford Company (WHC). The mitigation testing uses a pump immersed in the waste tank, directed at certain angles and operated at different speeds and time durations. The SY-101 tank has experienced recurrent periodic gas releases of hydrogen, nitrous oxide, ammonia, and (recently discovered) methane. The hydrogen gas represents a danger, as some of the releases are in amounts above the lower flammability limit (LFL). These large gas releases must be mitigated. Several instruments have been added to the tank to monitor the gas compositions, the tank level, the tank temperature, and other parameters. A mixer pump has been developed to stir the tank waste to cause the gases to be released at a slow rate. It is the function of the DACS to monitor those instruments and to control the mixer pump in a safe manner. During FY93 and FY94 the mixer pump was installed with associated testing operations support equipment and a mitigation test project plan was implemented. These activities successfully demonstrated the mixer pump`s ability to mitigate the SY-101 tank hydrogen gas hazard.

  15. The role of classification and reference vessels in the design of inland fairways for commercial vessels – contribution to the Workshop of WG 141 Design Guidelines for Inland Waterways

    NARCIS (Netherlands)

    Koedijk, O.C.

    2015-01-01

    The Pianc WG 141 is proceeding in the conception of Design Guidelines for Inland Waterways. WG 141 aims to produce its first draft in the end of 2015. Part of the forseen content are classification of waterways and the object of reference vessels. The role of those subjects will be presented and

  16. Reference masses for precision mass spectrometry design and implementation of a Pierce geometry to the cluster Ion source at ISOLTRAP

    CERN Document Server

    Lommen, Jonathan

    At the mass spectrometer ISOLTRAP carbon clusters ($^{12}$Cn, 1$\\leqslant$n$\\leqslant$25) are provided as reference masses, which are of particular importance in higher mass ranges (m $\\geqslant$ 200u). In this mass range the measurlment uncertainty is increasingly dominated by the difference of the reference mass and the mass of the ion of interest. Using carbon clusters instead of the common $^{133}$Cs ions, this difference decreases. The carbon clusters are produced in a laser ion source which has been improved in the frame of this thesis. The fluctuations of the count rate have been investigated as a function of the laser energy. Furthermore, the energy density at the target has been increased by implementation of a telescope into the laser beam line, which leads to a more narrow energy distribution of the ions. Through the exact adjustment of timing and length of a pulsed cavity an energy range with constant count rate could be selected. In order to provide ideal starting conditions during and after the ...

  17. Descriptive analysis of the type and design of contact lenses fitted according to keratoconus severity and morphology

    Directory of Open Access Journals (Sweden)

    Letícia Helena Lunardi

    2016-04-01

    Full Text Available ABSTRACT Purpose: Keratoconus is characterized by bilateral asymmetrical corneal ectasia that leads to inferior stromal thinning and corneal protrusion. There is currently a lack of consensus regarding the most efficacious method for fitting contact lenses in patients with keratoconus, given the various topographical patterns and evolution grades observed in affected populations. The purpose of the present study was to evaluate the association between keratoconus evolution grade and topography pattern and the type and design of fitted contact lens. Methods: We performed a retrospective analysis of contact lenses fitted in a total of 185 patients with keratoconus (325 eyes. Keratoconus was classified as either grade I, II, III, or IV based on keratometry and cone morphology (nipple, oval, globus, or indeterminate results. Results: A total of 325 eyes were evaluated in the present study. Of the 62 eyes classified as grade I, 66.1% were fitted with monocurve contact lenses. Of the 162 eyes classified as grade I and II, 51%, 30%, and 19% were fitted with adapted monocurve rigid gas-permeable contact lenses (RGPCL, bicurve lenses, and others lens types, respectively. Bicurve lenses were fitted in 52.1% and 62.2% of eyes classified as grade III and IV, respectively. Of the eyes classified as grade III and IV, monocurve and bicurve RGPCL were fitted in 26% and 55%, respectively. In eyes with oval keratoconus, 45%, 35%, and 20% were fitted with monocurve lenses, bicurve lenses, and other lens types, respectively. In eyes with round cones (nipple morphology, 55%, 30%, and 15% were fitted with bicurve lenses, monocurve lenses, and other lens types, respectively. Conclusion: Monocurve RGPCL were most frequently fitted in patients with mild to moderate keratoconus and oval cones morphology, while bicurve lenses were more frequently fitted in patients with severe and advanced keratoconus. This was probably because bicurve lenses are more appropriate for

  18. Descriptive analysis of the type and design of contact lenses fitted according to keratoconus severity and morphology.

    Science.gov (United States)

    Lunardi, Letícia Helena; Arroyo, Danielle; Andrade Sobrinho, Marcelo Vicente de; Lipener, César; Rosa, Juliana Maria da Silva

    2016-04-01

    Keratoconus is characterized by bilateral asymmetrical corneal ectasia that leads to inferior stromal thinning and corneal protrusion. There is currently a lack of consensus regarding the most efficacious method for fitting contact lenses in patients with keratoconus, given the various topographical patterns and evolution grades observed in affected populations. The purpose of the present study was to evaluate the association between keratoconus evolution grade and topography pattern and the type and design of fitted contact lens. We performed a retrospective analysis of contact lenses fitted in a total of 185 patients with keratoconus (325 eyes). Keratoconus was classified as either grade I, II, III, or IV based on keratometry and cone morphology (nipple, oval, globus, or indeterminate) results. A total of 325 eyes were evaluated in the present study. Of the 62 eyes classified as grade I, 66.1% were fitted with monocurve contact lenses. Of the 162 eyes classified as grade I and II, 51%, 30%, and 19% were fitted with adapted monocurve rigid gas-permeable contact lenses (RGPCL), bicurve lenses, and others lens types, respectively. Bicurve lenses were fitted in 52.1% and 62.2% of eyes classified as grade III and IV, respectively. Of the eyes classified as grade III and IV, monocurve and bicurve RGPCL were fitted in 26% and 55%, respectively. In eyes with oval keratoconus, 45%, 35%, and 20% were fitted with monocurve lenses, bicurve lenses, and other lens types, respectively. In eyes with round cones (nipple morphology), 55%, 30%, and 15% were fitted with bicurve lenses, monocurve lenses, and other lens types, respectively. Monocurve RGPCL were most frequently fitted in patients with mild to moderate keratoconus and oval cones morphology, while bicurve lenses were more frequently fitted in patients with severe and advanced keratoconus. This was probably because bicurve lenses are more appropriate for round cones due to increased corneal asphericity.

  19. Accounting for variation in designing greenhouse experiments with special reference to greenhouses containing plants on conveyor systems

    Science.gov (United States)

    2013-01-01

    Background There are a number of unresolved issues in the design of experiments in greenhouses. They include whether statistical designs should be used and, if so, which designs should be used. Also, are there thigmomorphogenic or other effects arising from the movement of plants on conveyor belts within a greenhouse? A two-phase, single-line wheat experiment involving four tactics was conducted in a conventional greenhouse and a fully-automated phenotyping greenhouse (Smarthouse) to investigate these issues. Results and discussion Analyses of our experiment show that there was a small east–west trend in total area of the plants in the Smarthouse. Analyses of the data from three multiline experiments reveal a large north–south trend. In the single-line experiment, there was no evidence of differences between trios of lanes, nor of movement effects. Swapping plant positions during the trial was found to decrease the east–west trend, but at the cost of increased error variance. The movement of plants in a north–south direction, through a shaded area for an equal amount of time, nullified the north–south trend. An investigation of alternative experimental designs for equally-replicated experiments revealed that generally designs with smaller blocks performed best, but that (nearly) trend-free designs can be effective when blocks are larger. Conclusions To account for variation in microclimate in a greenhouse, using statistical design and analysis is better than rearranging the position of plants during the experiment. For the relocation of plants to be successful requires that plants spend an equal amount of time in each microclimate, preferably during comparable growth stages. Even then, there is no evidence that this will be any more precise than statistical design and analysis of the experiment, and the risk is that it will not be successful at all. As for statistical design and analysis, it is best to use either (i) smaller blocks, (ii) (nearly) trend

  20. Accounting for variation in designing greenhouse experiments with special reference to greenhouses containing plants on conveyor systems.

    Science.gov (United States)

    Brien, Chris J; Berger, Bettina; Rabie, Huwaida; Tester, Mark

    2013-02-08

    There are a number of unresolved issues in the design of experiments in greenhouses. They include whether statistical designs should be used and, if so, which designs should be used. Also, are there thigmomorphogenic or other effects arising from the movement of plants on conveyor belts within a greenhouse? A two-phase, single-line wheat experiment involving four tactics was conducted in a conventional greenhouse and a fully-automated phenotyping greenhouse (Smarthouse) to investigate these issues. Analyses of our experiment show that there was a small east-west trend in total area of the plants in the Smarthouse. Analyses of the data from three multiline experiments reveal a large north-south trend. In the single-line experiment, there was no evidence of differences between trios of lanes, nor of movement effects. Swapping plant positions during the trial was found to decrease the east-west trend, but at the cost of increased error variance. The movement of plants in a north-south direction, through a shaded area for an equal amount of time, nullified the north-south trend. An investigation of alternative experimental designs for equally-replicated experiments revealed that generally designs with smaller blocks performed best, but that (nearly) trend-free designs can be effective when blocks are larger. To account for variation in microclimate in a greenhouse, using statistical design and analysis is better than rearranging the position of plants during the experiment. For the relocation of plants to be successful requires that plants spend an equal amount of time in each microclimate, preferably during comparable growth stages. Even then, there is no evidence that this will be any more precise than statistical design and analysis of the experiment, and the risk is that it will not be successful at all. As for statistical design and analysis, it is best to use either (i) smaller blocks, (ii) (nearly) trend-free arrangement of treatments with a linear trend term

  1. Design

    DEFF Research Database (Denmark)

    Jensen, Ole B.; Pettiway, Keon

    2017-01-01

    by designers, planners, etc. (staging from above) and mobile subjects (staging from below). A research agenda for studying situated practices of mobility and mobilities design is outlined in three directions: foci of studies, methods and approaches, and epistemologies and frames of thinking. Jensen begins......In this chapter, Ole B. Jensen takes a situational approach to mobilities to examine how ordinary life activities are structured by technology and design. Using “staging mobilities” as a theoretical approach, Jensen considers mobilities as overlapping, actions, interactions and decisions...... with a brief description of how movement is studied within social sciences after the “mobilities turn” versus the idea of physical movement in transport geography and engineering. He then explains how “mobilities design” was derived from connections between traffic and architecture. Jensen concludes...

  2. Romanian Seismic Design Code: Benchmarking Analyses with Reference to International Codes and Research Needs for Future Development

    Directory of Open Access Journals (Sweden)

    Iolanda-Gabriela CRAIFALEANU

    2011-01-01

    Full Text Available The paper presents conclusions from a technical benchmarking study, performed in order to analyze the performance of the provisions concerning seismic design of reinforced concrete frame structures, as specified by the Romanian seismic code (P100-1/2006. The Romanian code is analyzed with respect to the European standard EN 1998-1:2004, including its National Annex, and with the U. S. codes IBC 2009 and ACI 318 08. The benchmarking analyses were performed by designing a standard reinforced concrete structure according to each of the considered codes and by evaluating the seismic behavior of the structural designs thus obtained. Comparative assessments are made, as well as suggestions concerning potential future research directions, aimed to the improvement of the Romanian provisions in the field.

  3. Designing serological surveillance programmes to document freedom from disease with special reference to exotic viral diseases of pigs in Denmark

    DEFF Research Database (Denmark)

    Stark, K.D.C.; Mortensen, S.; Olsen, A.M.

    2000-01-01

    or herd); target age group (or target farm type); test characteristics and sample size. Issues related to these aspects are discussed and illustrated using the example of serological surveillance for exotic viral diseases in the pig population of Denmark, Sampling designs based on individual animal......Surveillance programmes based on laboratory screening tests are increasingly used to document freedom from disease in order to facilitate trade, The following aspects must be considered when designing such programmes: diseases to be selected; epidemiology of the diseases; unit of analysis (animal...

  4. Light-Weight Radioisotope Heater Unit final safety analysis report (LWRHU-FSAR): Volume 1: A. Introduction and executive summary: B. Reference Design Document (RDD)

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, E.W.

    1988-10-01

    The orbiter and probe portions of the National Aeronautics and Space Administration (NASA) Galileo spacecraft contain components which require auxiliary heat during the mission. To meet these needs, the Department of Energy's (DOE's) Office of Special Applications (OSA) has sponsored the design, fabrication, and testing of a one-watt encapsulated plutonium dioxide-fueled thermal heater named the Light-Weight Radioisotope Heater Unit (LWRHU). This report, prepared by Monsanto Research Corporation (MRC), addresses the radiological risks which might be encountered by people both at the launch area and worldwide should postulated mission failures or malfunctions occur, resulting in the release of the LWRHUs to the environment. Included are data from the design, mission descriptions, postulated accidents with their consequences, test data, and the derived source terms and personnel exposures for the various events. 11 refs., 44 figs., 11 tabs.

  5. Baseline layout and design of a 0.8 GW reference wind farm in the North Sea

    DEFF Research Database (Denmark)

    Bak, Thomas; Graham, Angus; Sapronova, Alla

    2017-01-01

    on capital cost is proposed. An electrical design is suggested, and cable losses are calculated together with the energy yield. An operation and maintenance model is suggested, and the associated operating cost determined. The models are then combined in a term for levelized cost of energy allowing layouts...

  6. Modeling, analysis, and design of stationary reference frame droop controlled parallel three-phase voltage source inverters

    DEFF Research Database (Denmark)

    Vasquez, Juan Carlos; Guerrero, Josep M.; Savaghebi, Mehdi

    2011-01-01

    Power electronics based microgrids consist of a number of voltage source inverters (VSIs) operating in parallel. In this paper, the modeling, control design, and stability analysis of three-phase VSIs are derived. The proposed voltage and current inner control loops and the mathematical models...

  7. Modeling, analysis, and design of stationary reference frame droop controlled parallel three-phase voltage source inverters

    DEFF Research Database (Denmark)

    Vasquez, Juan Carlos; Guerrero, Josep M.; Savaghebi, Mehdi

    2013-01-01

    Power electronics based MicroGrids consist of a number of voltage source inverters (VSIs) operating in parallel. In this paper, the modeling, control design, and stability analysis of parallel connected three-phase VSIs are derived. The proposed voltage and current inner control loops...

  8. Description des Outils (Mathematiques, Linguistiques et Informatiques) Impliques par la Construction d'une Chaine Automatique Integree de Traitement de L'information Textuelle et Graphique

    Science.gov (United States)

    Borillo, A.; And Others

    1973-01-01

    An English summary is provided for the article which gives the opportunity to solve original problems in linguistics, mathematics and computing science as well as to design descriptive and typological methods in archaeology. (6 references) (Author/SJ)

  9. Generalizing: The descriptive struggle

    Directory of Open Access Journals (Sweden)

    Barney G. Glaser, Ph.D.; Hon Ph.D.

    2006-11-01

    Full Text Available The literature is not kind to the use of descriptive generalizations. Authors struggle and struggle to find and rationalize a way to use them and then fail in spite of trying a myriad of work-arounds. And then we have Lincoln and Guba’s famous statement: “The only generalization is: there is no generalization” in referring to qualitative research. (op cit, p. 110 They are referring to routine QDA yielding extensive descriptions, but which tacitly include conceptual generalizations without any real thought of knowledge about them. In this chapter I wish to explore this struggle for the purpose of explaining that the various contra arguments to using descriptive generalizations DO NOT apply to the ease of using conceptual generalizations yielded in SGT and especially FGT. I will not argue for the use of descriptive generalization. I agree with Lincoln and Guba with respect to QDA, “the only generalization is: there is no generalization.” It is up to the QDA methodologists, of whom there are many; to continue the struggle and I wish them well.

  10. User’s Reference Manual: Computer Program for Design and Analysis of Inverted-T Retaining Walls and Floodwalls (TWDA).

    Science.gov (United States)

    1980-12-01

    kuSED FOR FSTIN (LOAD CASE 3) DE;AIT VALIE OF 2 ’,sFr FP9 ,S L I OE (LOAD CASE 3) ExAmPLE 2 .. ANALY7E EKIWIRIT PA WALI , THEN DESIGN WITH. MODULE...n ec 0 .270 *... c .. 9 A ,0p 39I2 n~~c 270 c... c c. cc...2 .~~. .*.e. . I ~ ,T ~ ’??0ccc.. .A3? oetft* F~~ A W A rI’. /F F FP9 A ’F 1A A..ce 1.~ 1

  11. Design of an e-registration prototype using HCI principles : with specific reference to tax registration / JT Terblanche

    OpenAIRE

    Terblanche, Juanita Tertia

    2013-01-01

    The aim of the research was: *to gain a better understanding on the concepts of Human-computer interaction (HCI) in general and the application of HCI principles in this field; to gain a better understanding of electronic registration systems (e-registration systems) and the use of web forms for this purpose; to gain a better understanding of which HCI principles could be applied to the design of a web form for e-registration; to apply the identified HCI principles to an example of a web ...

  12. Lacunas identified in syllabus design of English language teaching in Engineering Colleges: a study with special reference to Odisha, India

    Directory of Open Access Journals (Sweden)

    Dr. Priya. S

    2014-12-01

    Full Text Available Many universities have introduced Humanities subjects into the engineering streams in tune with trends practiced globally. Engineers need to inculcate the spirit of humanities to acquire team spirit, critical thinking abilities and also problem-solving abilities for career advancement. Language skills empower engineers to face future challenges globally. In India also, Communicative English and Business English/ Professional English have been integrated into the Humanities stream of undergraduate programs in all Engineering colleges. Under this background, this empirical study examines the problems related to syllabus designed in the existing curricula of English language through questionnaire survey which was administered to 770 students of 20 engineering colleges. Ten items questionnaire objectively aimed to analyze three different aspects of the course designed for engineers. Firstly, to find out how the implementation of the syllabus matches the language learning needs of the students of the digital age. Secondly, to examine the teaching methodologies of four language skills of listening, speaking, reading and writing and finally to investigate how far the students preferred lab classes to theory classes. On the basis of the responses elicited, the aspects related to their immediate need of a learner centered curriculum are represented through graphical data for better interpretation. The research, thus, aimed at throwing light on the strengths and weaknesses of the existing system and the need to envisage a paradigm shift for preparing global engineers in the context of fast emerging situations around the world.

  13. Gold-catalyzed aerobic epoxidation of trans-stilbene in methylcyclohexane. Part I: Design of a reference catalyst

    KAUST Repository

    Guillois, Kevin

    2012-02-01

    The kinetics of the heterogeneous gold-catalyzed aerobic epoxidation of stilbene in the liquid phase has been shown to be hindered by diffusion limitations, due to the use of supports which are unsuitable to apolar reaction media. The choice of these supports is generally dictated by the ability of standard methods of preparation to stabilize highly dispersed gold nanoparticles on them. Hence, new methods need to be designed in order to produce catalytically active gold nanoparticles on hydrophobic supports in general and on passivated silicas in particular. By investigating Tsukuda\\'s method to produce colloidal solutions of gold nanoparticles upon reduction of the triphenylphosphine gold chloride complex in solution, we found that direct reduction of AuPPh3Cl in the presence of a commercially available silica support functionalized with dimethylsiloxane, Aerosil R972, leads, in a highly reproducible and potentially scalable way, to the best catalyst ever reported for this reaction. (C) 2011 Elsevier BM. All rights reserved.

  14. Reference citation

    National Research Council Canada - National Science Library

    Brkić, Silvija

    2013-01-01

    .... This paper deals with different styles of reference citation. Special emphasis was placed on the Vancouver Style for reference citation in biomedical journals established by the International Committee of Medical Journal Editors...

  15. [Descriptive statistics].

    Science.gov (United States)

    Rendón-Macías, Mario Enrique; Villasís-Keever, Miguel Ángel; Miranda-Novales, María Guadalupe

    2016-01-01

    Descriptive statistics is the branch of statistics that gives recommendations on how to summarize clearly and simply research data in tables, figures, charts, or graphs. Before performing a descriptive analysis it is paramount to summarize its goal or goals, and to identify the measurement scales of the different variables recorded in the study. Tables or charts aim to provide timely information on the results of an investigation. The graphs show trends and can be histograms, pie charts, "box and whiskers" plots, line graphs, or scatter plots. Images serve as examples to reinforce concepts or facts. The choice of a chart, graph, or image must be based on the study objectives. Usually it is not recommended to use more than seven in an article, also depending on its length.

  16. The REFER (REFer for EchocaRdiogram protocol: a prospective validation of a clinical decision rule, NT-proBNP, or their combination, in the diagnosis of heart failure in primary care. Rationale and design

    Directory of Open Access Journals (Sweden)

    Tait Lynda

    2012-10-01

    Full Text Available Abstract Background Heart failure is a major cause of mortality and morbidity. As mortality rates are high, it is important that patients seen by general practitioners with symptoms suggestive of heart failure are identified quickly and treated appropriately. Identifying patients with heart failure or deciding which patients need further tests is a challenge. All patients with suspected heart failure should be diagnosed using objective tests such as echocardiography, but it is expensive, often delayed, and limited by the significant skill shortage of trained echocardiographers. Alternative approaches for diagnosing heart failure are currently limited. Clinical decision tools that combine clinical signs, symptoms or patient characteristics are designed to be used to support clinical decision-making and validated according to strict methodological procedures. The REFER Study aims to determine the accuracy and cost-effectiveness of our previously derived novel, simple clinical decision rule, a natriuretic peptide assay, or their combination, in the triage for referral for echocardiography of symptomatic adult patients who present in general practice with symptoms suggestive of heart failure. Methods/design This is a prospective, Phase II observational, diagnostic validation study of a clinical decision rule, natriuretic peptides or their combination, for diagnosing heart failure in primary care. Consecutive adult primary care patients 55 years of age or over presenting to their general practitioner with a chief complaint of recent new onset shortness of breath, lethargy or peripheral ankle oedema of over 48 hours duration, with no obvious recurrent, acute or self-limiting cause will be enrolled. Our reference standard is based upon a three step expert specialist consensus using echocardiography and clinical variables and tests. Discussion Our clinical decision rule offers a potential solution to the diagnostic challenge of providing a timely and

  17. Moderator design studies for a new neutron reference source based on the D-T fusion reaction

    Science.gov (United States)

    Mozhayev, Andrey V.; Piper, Roman K.; Rathbone, Bruce A.; McDonald, Joseph C.

    2016-06-01

    The radioactive isotope Californium-252 (252Cf) is relied upon internationally as a neutron calibration source for ionizing radiation dosimetry because of its high specific activity. The source may be placed within a heavy-water (D2O) moderating sphere to produce a softened spectrum representative of neutron fields common to commercial nuclear power plant environments, among others. Due to termination of the U.S. Department of Energy loan/lease program in 2012, the expense of obtaining 252Cf sources has undergone a significant increase, rendering high output sources largely unattainable. On the other hand, the use of neutron generators in research and industry applications has increased dramatically in recent years. Neutron generators based on deuteriumtritium (D-T) fusion reaction provide high neutron fluence rates and, therefore, could possibly be used as a replacement for 252Cf. To be viable, the 14 MeV D-T output spectrum must be significantly moderated to approximate common workplace environments. This paper presents the results of an effort to select appropriate moderating materials and design a configuration to reshape the primary neutron field toward a spectrum approaching that from a nuclear power plant workplace. A series of Monte-Carlo (MCNP) simulations of single layer high- and low-Z materials are used to identify initial candidate moderators. Candidates are refined through a similar series of simulations involving combinations of 2-5 different materials. The simulated energy distribution using these candidate moderators are rated in comparison to a target spectrum. Other properties, such as fluence preservation and/or enhancement, prompt gamma production and other characteristics are also considered.

  18. Moderator design studies for a new neutron reference source based on the D–T fusion reaction

    Energy Technology Data Exchange (ETDEWEB)

    Mozhayev, Andrey V.; Piper, Roman K.; Rathbone, Bruce A.; McDonald, Joseph C.

    2016-06-01

    The radioactive isotope Californium-252 (252Cf) is relied upon internationally as a neutron calibration source for ionizing radiation dosimetry because of its high specific activity. The source may be placed within a heavy-water (D2O) moderating sphere to produce a softened spectrum representative of neutron fields common to commercial nuclear power plant environments, among others. Due to termination of the U.S. Department of Energy loan/lease program in 2012, the expense of obtaining 252Cf sources has undergone a significant increase, rendering high output sources largely unattainable. On the other hand, the use of neutron generators in research and industry applications has increased dramatically in recent years. Neutron generators based on deuterium-tritium (D-T) fusion reaction provide high neutron fluence rates and, therefore, could possibly be used as a replacement for 252Cf. To be viable, the 14.6 MeV D-T output spectrum must be significantly moderated to approximate common workplace environments. This paper presents the results of an effort to select appropriate moderating materials and design a configuration to reshape the primary neutron field toward a spectrum approaching that from a nuclear power plant workplace. A series of Monte-Carlo (MCNP) simulations of single layer high- and low-Z materials are used to identify initial candidate moderators. Candidates are refined through a similar series of simulations involving combinations of 2 to 5 different materials. The simulated energy distribution using these candidate moderators are rated in comparison to a target spectrum. Other properties, such as fluence preservation and/or enhancement, prompt gamma production and other characteristics are also considered.

  19. Design and Fabrication of Low Cost Thick Film pH Sensor using Silver Chlorinated Reference Electrodes with Integrated Temperature Sensor

    Directory of Open Access Journals (Sweden)

    Wiranto Goib

    2016-01-01

    Full Text Available This paper describes the design and fabrication of thick film pH sensor, in which the reference electrode has been formed by chlorination of Ag using FeCl3. The process was aimed to replace Ag/AgCl paste commonly used as reference electrodes. Fabricated using thick film screen printing technology on Al2O3 substrate, the pH sensor showed a measured sensitivity of -52.97, -53.17 and -53.68 mV/pH at 25°C, 45°C, and 65°C, respectively. The measured values were close to the theoretical Nernstian slope of -59 mV/pH 25°C.The sensor was also designed with an integrated Ruthenium based temperature sensor for future temperature compensation. The measured resistance temperature characteristics showed a linear reasponse over the range of 25 – 80°C. This miniaturised planar sensor should find wide application, especially in field water quality monitoring, replacing their glass type counterparts.

  20. Nuclear Thermal Rocket/Vehicle Characteristics And Sensitivity Trades For NASA's Mars Design Reference Architecture (DRA) 5.0 Study

    Science.gov (United States)

    Borowski, Stanley K.; McCurdy, David R.; Packard, Thomas W.

    2009-01-01

    This paper summarizes Phase I and II analysis results from NASA's recent Mars DRA 5.0 study which re-examined mission, payload and transportation system requirements for a human Mars landing mission in the post-2030 timeframe. Nuclear thermal rocket (NTR) propulsion was again identified as the preferred in-space transportation system over chemical/aerobrake because of its higher specific impulse (I(sub sp)) capability, increased tolerance to payload mass growth and architecture changes, and lower total initial mass in low Earth orbit (IMLEO) which is important for reducing the number of Ares-V heavy lift launches and overall mission cost. DRA 5.0 features a long surface stay (approximately 500 days) split mission using separate cargo and crewed Mars transfer vehicles (MTVs). All vehicles utilize a common core propulsion stage with three 25 klbf composite fuel NERVA-derived NTR engines (T(sub ex) approximately 2650 - 2700 K, p(sub ch) approximately 1000 psia, epsilon approximately 300:1, I(sub sp) approximately 900 - 910 s, engine thrust-toweight ratio approximately 3.43) to perform all primary mission maneuvers. Two cargo flights, utilizing 1-way minimum energy trajectories, pre-deploy a cargo lander to the surface and a habitat lander into a 24-hour elliptical Mars parking orbit where it remains until the arrival of the crewed MTV during the next mission opportunity (approximately 26 months later). The cargo payload elements aerocapture (AC) into Mars orbit and are enclosed within a large triconicshaped aeroshell which functions as payload shroud during launch, then as an aerobrake and thermal protection system during Mars orbit capture and subsequent entry, descent and landing (EDL) on Mars. The all propulsive crewed MTV is a 0-gE vehicle design that utilizes a fast conjunction trajectory that allows approximately 6-7 month 1-way transit times to and from Mars. Four 12.5 kW(sub e) per 125 square meter rectangular photovoltaic arrays provide the crewed MTV with

  1. Nursing students' evaluation of a new feedback and reflection tool for use in high-fidelity simulation - Formative assessment of clinical skills. A descriptive quantitative research design.

    Science.gov (United States)

    Solheim, Elisabeth; Plathe, Hilde Syvertsen; Eide, Hilde

    2017-11-01

    Clinical skills training is an important part of nurses' education programmes. Clinical skills are complex. A common understanding of what characterizes clinical skills and learning outcomes needs to be established. The aim of the study was to develop and evaluate a new reflection and feedback tool for formative assessment. The study has a descriptive quantitative design. 129 students participated who were at the end of the first year of a Bachelor degree in nursing. After highfidelity simulation, data were collected using a questionnaire with 19 closed-ended and 2 open-ended questions. The tool stimulated peer assessment, and enabled students to be more thorough in what to assess as an observer in clinical skills. The tool provided a structure for selfassessment and made visible items that are important to be aware of in clinical skills. This article adds to simulation literature and provides a tool that is useful in enhancing peer learning, which is essential for nurses in practice. The tool has potential for enabling students to learn about reflection and developing skills for guiding others in practice after they have graduated. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. Epidemiologic study of residential proximity to transmission lines and childhood cancer in California: description of design, epidemiologic methods and study population.

    Science.gov (United States)

    Kheifets, Leeka; Crespi, Catherine M; Hooper, Chris; Oksuzyan, Sona; Cockburn, Myles; Ly, Thomas; Mezei, Gabor

    2015-01-01

    We conducted a large epidemiologic case-control study in California to examine the association between childhood cancer risk and distance from the home address at birth to the nearest high-voltage overhead transmission line as a replication of the study of Draper et al. in the United Kingdom. We present a detailed description of the study design, methods of case ascertainment, control selection, exposure assessment and data analysis plan. A total of 5788 childhood leukemia cases and 3308 childhood central nervous system cancer cases (included for comparison) and matched controls were available for analysis. Birth and diagnosis addresses of cases and birth addresses of controls were geocoded. Distance from the home to nearby overhead transmission lines was ascertained on the basis of the electric power companies' geographic information system (GIS) databases, additional Google Earth aerial evaluation and site visits to selected residences. We evaluated distances to power lines up to 2000 m and included consideration of lower voltages (60-69 kV). Distance measures based on GIS and Google Earth evaluation showed close agreement (Pearson correlation >0.99). Our three-tiered approach to exposure assessment allowed us to achieve high specificity, which is crucial for studies of rare diseases with low exposure prevalence.

  3. Five-year examination of utilization and drug cost outcomes associated with benefit design changes including reference pricing for proton pump inhibitors in a state employee health plan.

    Science.gov (United States)

    Johnson, Jill T; Neill, Kathryn K; Davis, Dwight A

    2011-04-01

    The Arkansas State Employee Benefits Division (EBD) is a self-insured program comprising public school and other state employees, their spouses, and dependents. Previous research published in JMCP (2006) showed drug cost savings of $2.20 per member per month (PMPM; 37.6%) or annualized savings of $3.4 million associated with a benefit design change and coverage of the proton pump inhibitor (PPI) omeprazole over-the-counter (OTC) beginning in March 2004. On May 1, 2005, brand esomeprazole was excluded from coverage, with current users grandfathered for 4 months until September 2005. Reference pricing for PPIs, including esomeprazole but excluding generic omeprazole, was implemented on September 1, 2005, and the beneficiary cost share for all PPIs except generic omeprazole was determined from comparison of the PPI actual price to the $0.90 omeprazole OTC reference price per unit. To examine PPI utilization and drug costs before and after (a) excluding esomeprazole from coverage (with grandfathering current users) and (b) implementing a therapeutic maximum allowable cost (TMAC), or reference-pricing benefit design, for the PPI class in a large state employee health plan with fairly stable enrollment of approximately 127,500 members in 2005 through 2008 and approximately 128,000 members in 2009 Q1. The pharmacy claims database for the EBD was used to examine utilization and cost data for PPIs in a longitudinal analysis for the 61-month period from March 1, 2004, through March 31, 2009. Pharmacy claims data were compared for the period 14 months prior to esomeprazole exclusion (preperiod), 4 months during the esomeprazole exclusion (postperiod 1), and the ensuing 43 months of PPI reference pricing (postperiod 2). PPI cost and utilization data for the intervention group of approximately 127,500 beneficiaries were compared with a group of 122 self-insured employers with a total of nearly 1 million beneficiaries whose pharmacy benefits did not include reference pricing for

  4. Programmable Logic Device (PLD) Design Description for the Integrated Power, Avionics, and Software (iPAS) Space Telecommunications Radio System (STRS) Radio

    Science.gov (United States)

    Shalkhauser, Mary Jo W.

    2017-01-01

    The Space Telecommunications Radio System (STRS) provides a common, consistent framework for software defined radios (SDRs) to abstract the application software from the radio platform hardware. The STRS standard aims to reduce the cost and risk of using complex, configurable and reprogrammable radio systems across NASA missions. To promote the use of the STRS architecture for future NASA advanced exploration missions, NASA Glenn Research Center (GRC) developed an STRS compliant SDR on a radio platform used by the Advance Exploration System program at the Johnson Space Center (JSC) in their Integrated Power, Avionics, and Software (iPAS) laboratory. At the conclusion of the development, the software and hardware description language (HDL) code was delivered to JSC for their use in their iPAS test bed to get hands-on experience with the STRS standard, and for development of their own STRS Waveforms on the now STRS compliant platform.The iPAS STRS Radio was implemented on the Reconfigurable, Intelligently-Adaptive Communication System (RIACS) platform, currently being used for radio development at JSC. The platform consists of a Xilinx ML605 Virtex-6 FPGA board, an Analog Devices FMCOMMS1-EBZ RF transceiver board, and an Embedded PC (Axiomtek eBox 620-110-FL) running the Ubuntu 12.4 operating system. Figure 1 shows the RIACS platform hardware. The result of this development is a very low cost STRS compliant platform that can be used for waveform developments for multiple applications.The purpose of this document is to describe the design of the HDL code for the FPGA portion of the iPAS STRS Radio particularly the design of the FPGA wrapper and the test waveform.

  5. Ozone Standard Reference Photometer

    Data.gov (United States)

    Federal Laboratory Consortium — The Standard Reference Photometer (SRP) Program began in the early 1980s as collaboration between NIST and the U.S. Environmental Protection Agency (EPA) to design,...

  6. Python pocket reference

    CERN Document Server

    Lutz, Mark

    2010-01-01

    This is the book to reach for when you're coding on the fly and need an answer now. It's an easy-to-use reference to the core language, with descriptions of commonly used modules and toolkits, and a guide to recent changes, new features, and upgraded built-ins -- all updated to cover Python 3.X as well as version 2.6. You'll also quickly find exactly what you need with the handy index. Written by Mark Lutz -- widely recognized as the world's leading Python trainer -- Python Pocket Reference, Fourth Edition, is the perfect companion to O'Reilly's classic Python tutorials, also written by Mark

  7. Multidimensional nonlinear descriptive analysis

    CERN Document Server

    Nishisato, Shizuhiko

    2006-01-01

    Quantification of categorical, or non-numerical, data is a problem that scientists face across a wide range of disciplines. Exploring data analysis in various areas of research, such as the social sciences and biology, Multidimensional Nonlinear Descriptive Analysis presents methods for analyzing categorical data that are not necessarily sampled randomly from a normal population and often involve nonlinear relations. This reference not only provides an overview of multidimensional nonlinear descriptive analysis (MUNDA) of discrete data, it also offers new results in a variety of fields. The first part of the book covers conceptual and technical preliminaries needed to understand the data analysis in subsequent chapters. The next two parts contain applications of MUNDA to diverse data types, with each chapter devoted to one type of categorical data, a brief historical comment, and basic skills peculiar to the data types. The final part examines several problems and then concludes with suggestions for futu...

  8. The use of SMIRP for the rapid design and implementation of pedagogical constructs: Case study of a question-answer-reference framework

    Directory of Open Access Journals (Sweden)

    Jeremy Boecker,

    2003-01-01

    Full Text Available The use of SMIRP, a web-based collaborative tool, for an application in an undergraduate and a graduate class is described. SMIRP was used to rapidly construct a collaborative space where students could work on their assignment, request assistance and view their grades. The pedagogical construct was based on a question-answer-reference model where students were required to answer a series of questions based only on the material present in references they selected from the open literature. The answers and grades of all students were visible to all students in real time, although pseudonyms were used to respect student privacy. Email alerts were provided to the teacher, teaching assistants and in the second class also to the students and a librarian. Based on the analysis of log files, overall student performance in the class was found to correlate positively with curiosity and negatively with procrastination. Student expectations of turnaround times for grades and general queries were also analyzed and compared to actual performance. At the end of both classes a questionnaire module was created and an analysis of student satisfaction and preferences is reported. The successful implementation of SMIRP in these two classes supports the contention that this collaborative tool is flexible enough for the rapid design and implementation of relatively complex pedagogical constructs, with the possibility of obtaining detailed metrics.

  9. Modelo multicritério para referência na fase de Projeto Informacional do Processo de Desenvolvimento de Produtos Multicriteria model as a reference in the informational design stage of the product development process

    Directory of Open Access Journals (Sweden)

    Elton Moura Nickel

    2010-12-01

    Full Text Available Este artigo compreende as etapas iniciais do Processo de Desenvolvimento de Produtos - mais especificamente a fase conhecida como Projeto Informacional -, considerando-as fundamentais para o sucesso de um novo produto no mercado. O fator complicador é que, durante essa fase do desenvolvimento, as diversas especificações e atributos do produto são definidos por se lidar com uma infinidade de critérios de escolha, com base nas necessidades dos clientes. Sendo assim, esta pesquisa visa propor uma nova sistematização da fase de Projeto Informacional, adequando-a aos métodos e ferramentas propostos pelas metodologias da decisão que tratam de problemas com múltiplos critérios, de modo a contribuir para a melhoria da prática de projeto nas suas fases iniciais. Com esse objetivo, desenvolve-se um modelo multicritério nos moldes do Modelo Unificado de Referência de Rozenfeld et al. (2006, ao propor métodos, ferramentas e documentos de apoio adequados ao cumprimento de cada atividade. As melhorias e os valores que a aplicação prática do modelo multicritério agrega ao Processo de Desenvolvimento de Produtos são discutidos mediante um estudo de caso referente ao projeto de produto comercial - um novo emissor de senhas.This paper includes the initial stages of the product development process - more specifically the stage known as Informational Design - considered to be fundamental to the success of a new product on the market. The complicating factor is that during this development stage the different specifications and attributes of the product are defined due to a multitude of choice criteria based on customer needs. Thus, this research aims to propose a new structure of the Informational Design stage by adapting it to the methods and tools offered by the methodologies of the decision that deal with multiple criteria problems in order to contribute to improve the initial stages of project practice. Hence, a multicriteria model based on

  10. Clinical evaluation study of the German network of disorders of sex development (DSD/intersexuality: study design, description of the study population, and data quality

    Directory of Open Access Journals (Sweden)

    Jürgensen Martina

    2009-04-01

    Full Text Available Abstract Background The German Network of Disorders of Sex Development (DSD/Intersexuality carried out a large scale clinical evaluation study on quality of life, gender identity, treatment satisfaction, coping, and problems associated with diagnoses and therapies in individuals with disorders of sex development (DSD. DSD are a heterogeneous group of various genetic disorders of sex determination or sex differentiation, all of which are rare conditions. In about half of all cases the molecular genetic diagnosis is unknown and diagnosis rests on clinical features. Methods and design The multi-centre clinical evaluation study includes short-term follow-up in some and cross-sectional assessments in all age and diagnostic groups fitting the criteria of DSD. Recruitment was from January 2005 until December 2007 in whole Germany and, additionally, in 2007 in Austria and German-speaking Switzerland. The study consists of a psychosocial inquiry for children, adolescents and their parents, and adults with standardized instruments and the collection of DSD-specific medical data by the attending physician. The main goal was the description of clinical outcomes and the health-care situation of individuals with DSD using a broad generic definition of DSD including all conditions with a mismatch of chromosomal, gonadal and phenotypical sex. 439 children and adolescents, their parents and adults with DSD participated. Discussion The clinical evaluation study represents the most comprehensive study in this clinical field. The paper discusses the study protocol, the data management and data quality as well as the classification used, and it describes the study population. Given the lack of large datasets in rare conditions such as DSD and often biased results from small scale clinical case series, the study aims to generate concrete hypotheses for evidence-based guidelines, which should be tested in further studies.

  11. Revaluation of biological variation of glycated hemoglobin (HbA(1c)) using an accurately designed protocol and an assay traceable to the IFCC reference system.

    Science.gov (United States)

    Braga, Federica; Dolci, Alberto; Montagnana, Martina; Pagani, Franca; Paleari, Renata; Guidi, Gian Cesare; Mosca, Andrea; Panteghini, Mauro

    2011-07-15

    Glycated hemoglobin (HbA(1c)) has a key role for diagnosing diabetes and monitoring glycemic state. As recently reviewed, available data on HbA(1c) biological variation show marked heterogeneity. Here we experimentally revaluated these data using a well designed protocol. We took five EDTA whole blood specimens from 18 apparently healthy subjects on the same day, every two weeks for two months. Samples were stored at -80°C until analysis and assayed in duplicate in a single run by Roche Tina-quant® Gen.2 immunoassay. Data were analyzed by the ANOVA. To assess the assay traceability to the IFCC reference method, we preliminarily carried out a correlation experiment. The bias (mean±SD) of the Roche immunoassay was 0.3%±0.7%, confirming the traceability of the employed assay. No difference was found in HbA(1c) values between men and women. Within- and between-subject CV were 2.5% and 7.1%, respectively. Derived desirable analytical goals for imprecision, bias, and total error resulted 1.3%, 1.9%, and 3.9%, respectively. HbA(1c) had marked individuality, limiting the use of population-based reference limits for test interpretation. The estimated critical difference was ~10%. For the first time we defined biological variation and derived indices for the clinical application of HbA(1c) measurements using an accurately designed protocol and an assay standardized according to the IFCC. Copyright © 2011 Elsevier B.V. All rights reserved.

  12. Monitored Geologic Repository Project Description Document

    Energy Technology Data Exchange (ETDEWEB)

    P. M. Curry

    2001-01-30

    The primary objective of the Monitored Geologic Repository Project Description Document (PDD) is to allocate the functions, requirements, and assumptions to the systems at Level 5 of the Civilian Radioactive Waste Management System (CRWMS) architecture identified in Section 4. It provides traceability of the requirements to those contained in Section 3 of the ''Monitored Geologic Repository Requirements Document'' (MGR RD) (YMP 2000a) and other higher-level requirements documents. In addition, the PDD allocates design related assumptions to work products of non-design organizations. The document provides Monitored Geologic Repository (MGR) technical requirements in support of design and performance assessment in preparing for the Site Recommendation (SR) and License Application (LA) milestones. The technical requirements documented in the PDD are to be captured in the System Description Documents (SDDs) which address each of the systems at Level 5 of the CRWMS architecture. The design engineers obtain the technical requirements from the SDDs and by reference from the SDDs to the PDD. The design organizations and other organizations will obtain design related assumptions directly from the PDD. These organizations may establish additional assumptions for their individual activities, but such assumptions are not to conflict with the assumptions in the PDD. The PDD will serve as the primary link between the technical requirements captured in the SDDs and the design requirements captured in US Department of Energy (DOE) documents. The approved PDD is placed under Level 3 baseline control by the CRWMS Management and Operating Contractor (M and O) and the following portions of the PDD constitute the Technical Design Baseline for the MGR: the design characteristics listed in Table 1-1, the MGR Architecture (Section 4.1), the Technical Requirements (Section 5), and the Controlled Project Assumptions (Section 6).

  13. Monitored Geologic Repository Project Description Document

    Energy Technology Data Exchange (ETDEWEB)

    P. Curry

    2001-06-26

    The primary objective of the Monitored Geologic Repository Project Description Document (PDD) is to allocate the functions, requirements, and assumptions to the systems at Level 5 of the Civilian Radioactive Waste Management System (CRWMS) architecture identified in Section 4. It provides traceability of the requirements to those contained in Section 3 of the Yucca Mountain Site Characterization Project Requirements Document (YMP RD) (YMP 2001a) and other higher-level requirements documents. In addition, the PDD allocates design related assumptions to work products of non-design organizations. The document provides Monitored Geologic Repository (MGR) technical requirements in support of design and performance assessment in preparing for the Site Recommendation (SR) and License Application (LA) milestones. The technical requirements documented in the PDD are to be captured in the System Description Documents (SDDs) which address each of the systems at Level 5 of the CRWMS architecture. The design engineers obtain the technical requirements from the SDDs and by reference from the SDDs to the PDD. The design organizations and other organizations will obtain design related assumptions directly from the PDD. These organizations may establish additional assumptions for their individual activities, but such assumptions are not to conflict with the assumptions in the PDD. The PDD will serve as the primary link between the technical requirements captured in the SDDs and the design requirements captured in US Department of Energy (DOE) documents. The approved PDD is placed under Level 3 baseline control by the CRWMS Management and Operating Contractor (M&O) and the following portions of the PDD constitute the Technical Design Baseline for the MGR: the design characteristics listed in Table 1-1, the MGR Architecture (Section 4.1), the Technical Requirements (Section 5), and the Controlled Project Assumptions (Section 6).

  14. Reference materials--a main element in a coherent reference measurement system.

    Science.gov (United States)

    Dybkaer, R

    1991-04-01

    The analytical reliability of any measurement procedure requires a specifically designed, coherent reference measurement system, including interrelated measurement procedures and measurement standards such as reference materials. The latter may be characterized by three sets of characteristics. The general characteristics comprise origin, mode of production, physical state and phase, homogeneity, physical form, container, additives, storage conditions, stability, and dangerous properties. The specific characteristics describe molecular composition, analyte, purity, matrix, quantity of interest (including scale), assigned value, and uncertainty of measurement. The additional characteristics concern the way in which values for other characteristics were obtained, the hierarchical position of the material, certificate, instructions for use, and intended function. The problem areas of reference materials comprise definition of the appropriate analyte, purification, matrix, assignment of values, and nomenclature. The present ambiguous terminology is presented and a systematic structure of descriptive names is proposed (tab. 1).

  15. Comparison of Occlusive and Open Application in a Psoriasis Plaque Test Design, Exemplarily Using Investigations of Mapracorat 0.1% Ointment versus Vehicle and Reference Drugs.

    Science.gov (United States)

    Wigger-Alberti, Walter; Williams, Ragna; von Mackensen, Yi-Ling; Hoffman-Wecker, Maciej; Grossmann, Ulrike; Staedtler, Gerald; Nkulikiyinka, Richard; Shakery, Kaweh

    2017-01-01

    Psoriasis plaque tests (PPTs) are important tools in the early phases of antipsoriatic drug development. Two distinct PPT design variants (open vs. occluded drug application) are commonly used, but no previous work has aimed to directly compare and contrast their performance. We compared the antipsoriatic efficacy of mapracorat 0.1% ointment and reference drugs reported in 2 separate studies, representing open and occluded PPT designs. The drug effect size was measured by sonography (mean change in echo-poor band thickness), chromametry, and standardized clinical assessment. Antipsoriatic effects were detectable for the study drugs in both occluded and open PPTs. Differences between the potency of antipsoriatic drugs and vehicle were observable. The total antipsoriatic effect size appeared to be higher in the occluded PPT than the open PPT, despite the shorter treatment duration (2 vs. 4 weeks). Effect dynamics over time revealed greater differences between some study drugs in the open PPT compared to the occluded PPT. Taking the higher technical challenges for the open PPT into account, we recommend the occluded PPT as a standard screening setting in early drug development. In special cases, considering certain drug aspects or study objectives that would require procedural adaptations, an open PPT could be the better-suited design. Finally, both PPT models show clear advantages: classification as phase I studies, small number of psoriatic subjects, relatively short study duration, excellent discrimination between compounds and concentrations, parallel measurement of treatment response, and go/no go decisions very early in clinical development. © 2017 S. Karger AG, Basel.

  16. Numerical study on criteria for design and operation of water curtain system in underground oil storage cavern using site descriptive fracture networks

    Science.gov (United States)

    Moon, Jiwon; Yeo, In Wook

    2013-04-01

    Underground unlined caverns have been constructed in fractured rocks to stockpile oil and petroleum products, where they are hydraulically contained by natural groundwater pressure. However, for the case that natural groundwater pressure is not maintained at the required level, water curtain boreholes, through which water is injected, are often constructed above the cavern as engineering barrier to secure water pressure enough to overwhelm the operational pressure of the cavern. For secure containment of oil and petroleum products inside the cavern, it is essential to keep water pressure around the cavern higher than operational pressure of the cavern using either natural groundwater pressure or engineering barrier. In the Republic of Korea, a number of underground stockpile bases are being operated by Korea National Oil Corporation (KNOC) and private companies, most of which have water curtain system. The criterion that KNOC adopts for water curtain system design and operation such as the vertical distance from the cavern and operational injection rate is based on the Åberg hypothesis that the vertical hydraulic gradient should be larger than one. The criterion has been used for maintaining oil storage cavern without its thorough review. In this study, systematic numerical works have been done for reviewing the Åberg criterion. As groundwater predominantly takes places through fractures in underground caverns, discrete fracture modeling approach is essential for this study. Fracture data, obtained from boreholes drilled at the stage of site investigation at the Yeosu stockpile base in Korea, were statistically analyzed in terms of orientation and intensity, which were used to generate the site descriptive three dimensional fracture networks. Then, groundwater flow modeling has been carried out for the fracture networks. Constant head boundaries were applied along the circumference of the cavern and water curtain boreholes. Main flow channel and hydraulic

  17. Reference Materials

    Science.gov (United States)

    Merkus, Henk G.

    Reference materials for measurement of particle size and porosity may be used for calibration or qualification of instruments or for validation of operating procedures or operators. They cover a broad range of materials. On the one hand there are the certified reference materials, for which governmental institutes have certified one or more typical size or porosity values. Then, there is a large group of reference materials from commercial companies. And on the other hand there are typical products in a given line of industry, where size or porosity values come from the analysis laboratory itself or from some round-robin test in a group of industrial laboratories. Their regular application is essential for adequate quality control of particle size and porosity measurement, as required in e.g., ISO 17025 on quality management. In relation to this, some quality requirements for certification are presented.

  18. "Grid" versus "Ground": Optimized Design of Low-Distortion Projections Using Existing Projection Types Rigorously Georeferenced to the National Spatial Reference System

    Science.gov (United States)

    Dennis, M. L.; Armstrong, M. L.

    2016-12-01

    With the adoption of a new geometric datum in 2022, NOAA's National Geodetic Survey (NGS) will update the State Plane Coordinate System (SPCS). This update may consist simply of offsetting northings and/or eastings of existing SPCS projection zones. However, there is significant interest among NGS customers for another type of projected coordinate system: Low-Distortion Projections (LDPs). Although LDPs are presently not endorsed or supported by NGS, an assessment of LDP feasibility and performance is warranted within the context of updating the National Spatial Reference System (NSRS). LDPs are conformal map projections that minimize linear distortion at the topographic surface, manifested as a difference in distance between a pair of projected "grid" coordinates and the true horizontal "ground" distance. For SPCS, the differences can exceed a few hundred parts per million (ppm), and it can be problematic for engineering and surveying applications. Although such distortion cannot be eliminated, an LDP design method is presented that yields optimal results even for large areas of variable elevation. This approach can provide much lower distortion than the traditional method of scaling SPCS to ground, often called "modified" SPCS (MSPCS). MSPCS was included in training provided by NGS beginning in the 1960s, but it does not optimally minimize linear distortion. LDP systems have been adopted throughout the United States. One such system is the Oregon Coordinate Reference System (OCRS). Figure 1 compares distortion of an MSPCS for Bend, Oregon, to the OCRS zone for that area, where the green shading indicates distortion within ±20 ppm (2 cm/km or 0.1 ft/mile). The difference in performance is striking, even though both use the same projection type. Because LDPs cover larger areas, one can be used for many projects, whereas in most cases one MSPCS (and sometimes more) must be defined for every project. Importantly, the presented method for designing LDPs is based on

  19. Value-Based Assessment of Radiology Reporting Using Radiologist-Referring Physician Two-Way Feedback System-a Design Thinking-Based Approach.

    Science.gov (United States)

    Shaikh, Faiq; Hendrata, Kenneth; Kolowitz, Brian; Awan, Omer; Shrestha, Rasu; Deible, Christopher

    2017-06-01

    In the era of value-based healthcare, many aspects of medical care are being measured and assessed to improve quality and reduce costs. Radiology adds enormously to health care costs and is under pressure to adopt a more efficient system that incorporates essential metrics to assess its value and impact on outcomes. Most current systems tie radiologists' incentives and evaluations to RVU-based productivity metrics and peer-review-based quality metrics. In a new potential model, a radiologist's performance will have to increasingly depend on a number of parameters that define "value," beginning with peer review metrics that include referrer satisfaction and feedback from radiologists to the referring physician that evaluates the potency and validity of clinical information provided for a given study. These new dimensions of value measurement will directly impact the cascade of further medical management. We share our continued experience with this project that had two components: RESP (Referrer Evaluation System Pilot) and FRACI (Feedback from Radiologist Addressing Confounding Issues), which were introduced to the clinical radiology workflow in order to capture referrer-based and radiologist-based feedback on radiology reporting. We also share our insight into the principles of design thinking as applied in its planning and execution.

  20. CSS Pocket Reference

    CERN Document Server

    Meyer, Eric

    2011-01-01

    When you're working with CSS and need a quick answer, CSS Pocket Reference delivers. This handy, concise book provides all of the essential information you need to implement CSS on the fly. Ideal for intermediate to advanced web designers and developers, the 4th edition is revised and updated for CSS3, the latest version of the Cascading Style Sheet specification. Along with a complete alphabetical reference to CSS3 selectors and properties, you'll also find a short introduction to the key concepts of CSS. Based on Cascading Style Sheets: The Definitive Guide, this reference is an easy-to-us

  1. HTML & XHTML Pocket Reference

    CERN Document Server

    Robbins, Jennifer

    2010-01-01

    After years of using spacer GIFs, layers of nested tables, and other improvised solutions for building your web sites, getting used to the more stringent standards-compliant design can be intimidating. HTML and XHTML Pocket Reference is the perfect little book when you need answers immediately. Jennifer Niederst-Robbins, author Web Design in a Nutshell, has revised and updated the fourth edition of this pocket guide by taking the top 20% of vital reference information from her Nutshell book, augmenting it judiciously, cross-referencing everything, and organizing it according to the most com

  2. The offline Lagrangian particle model FLEXPART-NorESM/CAM (v1): model description and comparisons with the online NorESM transport scheme and with the reference FLEXPART model

    Science.gov (United States)

    Cassiani, Massimo; Stohl, Andreas; Olivié, Dirk; Seland, Øyvind; Bethke, Ingo; Pisso, Ignacio; Iversen, Trond

    2016-11-01

    The offline FLEXible PARTicle (FLEXPART) stochastic dispersion model is currently a community model used by many scientists. Here, an alternative FLEXPART model version has been developed and tailored to use with the meteorological output data generated by the CMIP5-version of the Norwegian Earth System Model (NorESM1-M). The atmospheric component of the NorESM1-M is based on the Community Atmosphere Model (CAM4); hence, this FLEXPART version could be widely applicable and it provides a new advanced tool to directly analyse and diagnose atmospheric transport properties of the state-of-the-art climate model NorESM in a reliable way. The adaptation of FLEXPART to NorESM required new routines to read meteorological fields, new post-processing routines to obtain the vertical velocity in the FLEXPART coordinate system, and other changes. These are described in detail in this paper. To validate the model, several tests were performed that offered the possibility to investigate some aspects of offline global dispersion modelling. First, a comprehensive comparison was made between the tracer transport from several point sources around the globe calculated online by the transport scheme embedded in CAM4 and the FLEXPART model applied offline on output data. The comparison allowed investigating several aspects of the transport schemes including the approximation introduced by using an offline dispersion model with the need to transform the vertical coordinate system, the influence on the model results of the sub-grid-scale parameterisations of convection and boundary layer height and the possible advantage entailed in using a numerically non-diffusive Lagrangian particle solver. Subsequently, a comparison between the reference FLEXPART model and the FLEXPART-NorESM/CAM version was performed to compare the well-mixed state of the atmosphere in a 1-year global simulation. The two model versions use different methods to obtain the vertical velocity but no significant difference

  3. Foundations for Tools as a Service Workspace: A Reference Architecture

    DEFF Research Database (Denmark)

    Chauhan, Muhammad Aufeef

    2016-01-01

    Nowadays, on-demand provisioning of computing resources following a payper- use service model have enabled client organizations to have easy and on the fly access to the resources. The resources that are provisioned using the service model are generally characterized as resource as a Service (*aa...... on addressing the challenges using an architecture centric solution by providing a Software Reference Architecture for TSPACE. As a specific case, software architecting domain and the tools used for software architecting have been focused in this dissertation. This dissertation explores (a) the challenges...... associated with software architecting of cloud-enabled systems, (b) TSPACE reference architecture design guidelines, (c) TSPACE requirements, (d) information structuring needs and methods of TSPACE reference architecture, (e) a detailed description of TSPACE reference architecture sub-systems and components...

  4. Optimal Performance Design Guideline of Hybrid Reference Frame-based Dual Loop Control Strategy for Stand-Alone Single-Phase Inverters

    DEFF Research Database (Denmark)

    Han, Yang; Jiang, Ai-Ting; Coelho, Ernane A. A.

    2018-01-01

    The dual-loop control strategies in hybrid reference frame (HRF) for single-phase voltage source inverters (VSIs) in islanded operation mode is studied, which applies a capacitor voltage shaping loop in the synchronous reference frame (SRF) and a capacitor current shaping loop in the stationary r...

  5. Computer classes and games in virtual reality environment to reduce loneliness among students of an elderly reference center: Study protocol for a randomised cross-over design.

    Science.gov (United States)

    Antunes, Thaiany Pedrozo Campos; Oliveira, Acary Souza Bulle de; Crocetta, Tania Brusque; Antão, Jennifer Yohanna Ferreira de Lima; Barbosa, Renata Thais de Almeida; Guarnieri, Regiani; Massetti, Thais; Monteiro, Carlos Bandeira de Mello; Abreu, Luiz Carlos de

    2017-03-01

    Physical and mental changes associated with aging commonly lead to a decrease in communication capacity, reducing social interactions and increasing loneliness. Computer classes for older adults make significant contributions to social and cognitive aspects of aging. Games in a virtual reality (VR) environment stimulate the practice of communicative and cognitive skills and might also bring benefits to older adults. Furthermore, it might help to initiate their contact to the modern technology. The purpose of this study protocol is to evaluate the effects of practicing VR games during computer classes on the level of loneliness of students of an elderly reference center. This study will be a prospective longitudinal study with a randomised cross-over design, with subjects aged 50 years and older, of both genders, spontaneously enrolled in computer classes for beginners. Data collection will be done in 3 moments: moment 0 (T0) - at baseline; moment 1 (T1) - after 8 typical computer classes; and moment 2 (T2) - after 8 computer classes which include 15 minutes for practicing games in VR environment. A characterization questionnaire, the short version of the Short Social and Emotional Loneliness Scale for Adults (SELSA-S) and 3 games with VR (Random, MoviLetrando, and Reaction Time) will be used. For the intervention phase 4 other games will be used: Coincident Timing, Motor Skill Analyser, Labyrinth, and Fitts. The statistical analysis will compare the evolution in loneliness perception, performance, and reaction time during the practice of the games between the 3 moments of data collection. Performance and reaction time during the practice of the games will also be correlated to the loneliness perception. The protocol is approved by the host institution's ethics committee under the number 52305215.3.0000.0082. Results will be disseminated via peer-reviewed journal articles and conferences. This clinical trial is registered at ClinicalTrials.gov identifier: NCT

  6. Reference commercial fusion power plants

    Energy Technology Data Exchange (ETDEWEB)

    Young, J.R.; Gore, B.F.

    1976-09-01

    Currently available conceptual designs for commercial fusion power plants are for first generation plants using deuterium-tritium (D-T) fuel, and are all functionally similar. This similarity has been used as a basis for defining an envelope of D-T fusion power plant characteristics which encompasses the characteristics of the available designs. A description of this envelope, including general process descriptions, proposed materials uses and a tabulation of numerical ranges of plant parameters is presented in this document.

  7. The Identification and Description of Critical Thinking Behaviors in the Practice of Clinical Laboratory Science, Part 1: Design, Implementation, Evaluation, and Results of a National Survey.

    Science.gov (United States)

    Kenimer, Elizabeth A.

    2002-01-01

    A survey of 1,562 clinical laboratory scientists ranked critical thinking behaviors used in practice. Important behaviors were cognitive, behavioral, affective, and situated/contextual. Findings support a view of critical thinking as a metaprocess that spans learning domains. (Contains 17 references.) (SK)

  8. Python essential reference

    CERN Document Server

    Beazley, David M

    2009-01-01

    Python Essential Reference is the definitive reference guide to the Python programming language — the one authoritative handbook that reliably untangles and explains both the core Python language and the most essential parts of the Python library. Designed for the professional programmer, the book is concise, to the point, and highly accessible. It also includes detailed information on the Python library and many advanced subjects that is not available in either the official Python documentation or any other single reference source. Thoroughly updated to reflect the significant new programming language features and library modules that have been introduced in Python 2.6 and Python 3, the fourth edition of Python Essential Reference is the definitive guide for programmers who need to modernize existing Python code or who are planning an eventual migration to Python 3. Programmers starting a new Python project will find detailed coverage of contemporary Python programming idioms.

  9. School-Based Peer-Related Social Competence Interventions for Children with Autism Spectrum Disorder: A Meta-Analysis and Descriptive Review of Single Case Research Design Studies

    Science.gov (United States)

    Whalon, Kelly J.; Conroy, Maureen A.; Martinez, Jose R.; Werch, Brittany L.

    2015-01-01

    The purpose of this review was to critically examine and summarize the impact of school-based interventions designed to facilitate the peer-related social competence of children with autism spectrum disorder (ASD). Reviewed studies employed a single-case experimental design, targeted peer-related social competence, included children 3-12 years old…

  10. SURFACE INDUSTRIAL HVAC SYSTEM DESCRIPTION DOCUMENT

    Energy Technology Data Exchange (ETDEWEB)

    M.M. Ansari

    2005-04-05

    The purpose of this system description document (SDD) is to establish requirements that drive the design of the surface industrial heating, ventilation, and air-conditioning (HVAC) system and its bases to allow the design effort to proceed to license application. This SDD will be revised at strategic points as the design matures. This SDD identifies the requirements and describes the system design, as it currently exists, with emphasis on attributes of the design provided to meet the requirements. This SDD is an engineering tool for design control; accordingly, the primary audience and users are design engineers. This SDD is part of an iterative design process. It leads the design process with regard to the flowdown of upper tier requirements onto the system. Knowledge of these requirements is essential to performing the design process. The SDD follows the design with regard to the description of the system. The description that provided in this SDD reflects the current results of the design process.

  11. A time stepping coupled finite element-state space modeling environment for synchronous machine performance and design analysis in the ABC frame of reference

    Science.gov (United States)

    Deng, Fang

    iteratively used in obtaining inductance parameters prior to another round of SS computation of the steady-state current profiles. Again, the model is iterative in nature, in which the user continues cycling through the two sections, namely the FE and SS sections of the CFE-SS modeling environment, until the desired degree of convergence is achieved. The CFE-SS approach uses only design data such as physical dimensions, magnetic circuit geometry, magnetic material characteristics, winding particulars and layouts, and hence does not depend on the existence of actual hardware. The modeling environment is totally within the ABC frame of reference, therefore no approximating assumptions such as sinusoidally distributed mmf's or current sheets were made.

  12. ELECTRICAL SUPPORT SYSTEM DESCRIPTION DOCUMENT

    Energy Technology Data Exchange (ETDEWEB)

    S. Roy

    2004-06-24

    The purpose of this revision of the System Design Description (SDD) is to establish requirements that drive the design of the electrical support system and their bases to allow the design effort to proceed to License Application. This SDD is a living document that will be revised at strategic points as the design matures over time. This SDD identifies the requirements and describes the system design as they exist at this time, with emphasis on those attributes of the design provided to meet the requirements. This SDD has been developed to be an engineering tool for design control. Accordingly, the primary audience/users are design engineers. This type of SDD both ''leads'' and ''trails'' the design process. It leads the design process with regard to the flow down of upper tier requirements onto the system. Knowledge of these requirements is essential in performing the design process. The SDD trails the design with regard to the description of the system. The description provided in the SDD is a reflection of the results of the design process to date. Functional and operational requirements applicable to electrical support systems are obtained from the ''Project Functional and Operational Requirements'' (F&OR) (Siddoway 2003). Other requirements to support the design process have been taken from higher-level requirements documents such as the ''Project Design Criteria Document'' (PDC) (Doraswamy 2004), and fire hazards analyses. The above-mentioned low-level documents address ''Project Requirements Document'' (PRD) (Canon and Leitner 2003) requirements. This SDD contains several appendices that include supporting information. Appendix B lists key system charts, diagrams, drawings, and lists, and Appendix C includes a list of system procedures.

  13. Passive solar in Milton Keynes, England. A description of some of the more numerical aspects of the design of an estate of low energy houses

    Science.gov (United States)

    Everett, R.

    1980-07-01

    The numerical aspects of the design of low energy consumption houses using passive solar energy collection and high levels of insulation are described. Two housing energy conservation projects were begun, one involving the construction of 177 low energy houses on a cost-effective basis, and the other involving the detailed monitoring of eight highly insulated passive solar houses. Both experimental data and theoretical analysis are presented, and the relative effectiveness of the various design alternatives are discussed.

  14. ELECTRICAL POWER SYSTEM DESCRIPTION DOCUMENT

    Energy Technology Data Exchange (ETDEWEB)

    M. Maniyar

    2004-06-22

    The purpose of this revision of the System Description Document (SDD) is to establish requirements that drive the design of the electrical power system and their bases to allow the design effort to proceed to License Application. This SDD is a living document that will be revised at strategic points as the design matures over time. This SDD identifies the requirements and describes the system design as they exist at this time, with emphasis on those attributes of the design provided to meet the requirements. This SDD has been developed to be an engineering tool for design control. Accordingly, the primary audience are design engineers. This type of SDD leads and follows the design process. It leads the design process with regard to the flow down of upper tier requirements onto the system. Knowledge of these requirements is essential to performing the design process. This SDD follows the design with regard to the description of the system. The description provided in the SDD is a reflection of the results of the design process to date. Functional and operational requirements applicable to this system are obtained from ''Project Functional and Operational Requirements'' (F&OR) (Siddoway, 2003). Other requirements to support the design process have been taken from higher level requirements documents such as ''Project Design Criteria Document'' (PDC) (Doraswamy 2004), the fire hazards analyses, and the preclosure safety analysis. The above mentioned low-level documents address ''Project Requirements Document'' (PRD) (Canori and Leitner 2003) requirements. This SDD includes several appendices with supporting information. Appendix B lists key system charts, diagrams, drawings, and lists; and Appendix C is a list of system procedures.

  15. Case Study Regarding the Design of a Direct Current Electromagnet for the MIG Welding of Metallic Materials Part I: Description of the Welding Methods and Preliminary Calculus of the Electromagnet

    Directory of Open Access Journals (Sweden)

    Tudorel Ene

    2016-10-01

    Full Text Available The paper refers to the design of a direct current electromagnet, located on the head of a swan neck welding gun of a MIG welding equipment and used for magnetising the rotation space of two additional electric arches, in order to preheat the electrode wire and of the protective gas, partially turned into plasma jet. One describes the MIG welding method in which the electromagnet is used as well as its preliminary calculus.

  16. CSS Pocket Reference

    CERN Document Server

    Meyer, Eric A

    2007-01-01

    They say that good things come in small packages, and it's certainly true for this edition of CSS Pocket Reference. Completely revised and updated to reflect the latest Cascading Style Sheet specifications in CSS 2.1, this indispensable little book covers the most essential information that web designers and developers need to implement CSS effectively across all browsers. Inside, you'll find: A short introduction to the key concepts of CSS A complete alphabetical reference to all CSS 2.1 selectors and properties A chart displaying detailed information about CSS support for every style ele

  17. Development of integrated programs for Aerospace-vehicle Design (IPAD): Product program management systems

    Science.gov (United States)

    Isenberg, J. M.; Southall, J. W.

    1979-01-01

    The Integrated Programs for Aerospace Vehicle Design (IPAD) is a computing system to support company-wide design information processing. This document presents a brief description of the management system used to direct and control a product-oriented program. This document, together with the reference design process (CR 2981) and the manufacture interactions with the design process (CR 2982), comprises the reference information that forms the basis for specifying IPAD system requirements.

  18. Enterprise Reference Library

    Science.gov (United States)

    Bickham, Grandin; Saile, Lynn; Havelka, Jacque; Fitts, Mary

    2011-01-01

    Introduction: Johnson Space Center (JSC) offers two extensive libraries that contain journals, research literature and electronic resources. Searching capabilities are available to those individuals residing onsite or through a librarian s search. Many individuals have rich collections of references, but no mechanisms to share reference libraries across researchers, projects, or directorates exist. Likewise, information regarding which references are provided to which individuals is not available, resulting in duplicate requests, redundant labor costs and associated copying fees. In addition, this tends to limit collaboration between colleagues and promotes the establishment of individual, unshared silos of information The Integrated Medical Model (IMM) team has utilized a centralized reference management tool during the development, test, and operational phases of this project. The Enterprise Reference Library project expands the capabilities developed for IMM to address the above issues and enhance collaboration across JSC. Method: After significant market analysis for a multi-user reference management tool, no available commercial tool was found to meet this need, so a software program was built around a commercial tool, Reference Manager 12 by The Thomson Corporation. A use case approach guided the requirements development phase. The premise of the design is that individuals use their own reference management software and export to SharePoint when their library is incorporated into the Enterprise Reference Library. This results in a searchable user-specific library application. An accompanying share folder will warehouse the electronic full-text articles, which allows the global user community to access full -text articles. Discussion: An enterprise reference library solution can provide a multidisciplinary collection of full text articles. This approach improves efficiency in obtaining and storing reference material while greatly reducing labor, purchasing and

  19. YUCCA MOUNTAIN SITE DESCRIPTION

    Energy Technology Data Exchange (ETDEWEB)

    A.M. Simmons

    2004-04-16

    The ''Yucca Mountain Site Description'' summarizes, in a single document, the current state of knowledge and understanding of the natural system at Yucca Mountain. It describes the geology; geochemistry; past, present, and projected future climate; regional hydrologic system; and flow and transport within the unsaturated and saturated zones at the site. In addition, it discusses factors affecting radionuclide transport, the effect of thermal loading on the natural system, and tectonic hazards. The ''Yucca Mountain Site Description'' is broad in nature. It summarizes investigations carried out as part of the Yucca Mountain Project since 1988, but it also includes work done at the site in earlier years, as well as studies performed by others. The document has been prepared under the Office of Civilian Radioactive Waste Management quality assurance program for the Yucca Mountain Project. Yucca Mountain is located in Nye County in southern Nevada. The site lies in the north-central part of the Basin and Range physiographic province, within the northernmost subprovince commonly referred to as the Great Basin. The basin and range physiography reflects the extensional tectonic regime that has affected the region during the middle and late Cenozoic Era. Yucca Mountain was initially selected for characterization, in part, because of its thick unsaturated zone, its arid to semiarid climate, and the existence of a rock type that would support excavation of stable openings. In 1987, the United States Congress directed that Yucca Mountain be the only site characterized to evaluate its suitability for development of a geologic repository for high-level radioactive waste and spent nuclear fuel.

  20. Setting reference targets

    Energy Technology Data Exchange (ETDEWEB)

    Ruland, R.E.

    1997-04-01

    Reference Targets are used to represent virtual quantities like the magnetic axis of a magnet or the definition of a coordinate system. To explain the function of reference targets in the sequence of the alignment process, this paper will first briefly discuss the geometry of the trajectory design space and of the surveying space, then continue with an overview of a typical alignment process. This is followed by a discussion on magnet fiducialization. While the magnetic measurement methods to determine the magnetic centerline are only listed (they will be discussed in detail in a subsequent talk), emphasis is given to the optical/mechanical methods and to the task of transferring the centerline position to reference targets.

  1. Epsilon. A System Description Language

    DEFF Research Database (Denmark)

    Jensen, Kurt; Kyng, Morten

    This paper discusses the use of Petri nets as a semantic tool in the design of languages and in the construction and analysis of system descriptions. The topics treated are: -- Languages based on nets. -- The problem of time in nets. -- Nets and related models. -- Nets and formal semantics...

  2. Description of Specimens in the Marine Mammal Osteology Reference Collection

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The NMFS Alaska Fisheries Science Center National Marine Mammal Laboratory (NMML) Marine Mammal Osteology Collection consists of approximately 2500 specimens (skulls...

  3. Hadl: HUMS Architectural Description Language

    Science.gov (United States)

    Mukkamala, R.; Adavi, V.; Agarwal, N.; Gullapalli, S.; Kumar, P.; Sundaram, P.

    2004-01-01

    Specification of architectures is an important prerequisite for evaluation of architectures. With the increase m the growth of health usage and monitoring systems (HUMS) in commercial and military domains, the need far the design and evaluation of HUMS architectures has also been on the increase. In this paper, we describe HADL, HUMS Architectural Description Language, that we have designed for this purpose. In particular, we describe the features of the language, illustrate them with examples, and show how we use it in designing domain-specific HUMS architectures. A companion paper contains details on our design methodology of HUMS architectures.

  4. Research on conceptual design of mechatronic systems

    Indian Academy of Sciences (India)

    phase of mechatronic systems, a conceptual design cyclic feedback solving model of a mechatronic ... Thus, research on matching of component interfaces is an indispensable base for mechatronic ..... 661). References. Bracewell R H, Sharpe J E E 1996 Functional descriptions used in computer support for qualitative.

  5. Determination of the specific needs for ESP course and materials design: a descriptive study at Osmangazi University, Eskişehir

    OpenAIRE

    Tezcan, Hüseyin

    1998-01-01

    Ankara : The Institute of Economics and Social Sciences of Bilkent Univ., 1998. Thesis (Master's) -- Bilkent University, 1998. Includes bibliographical refences. English for Specific Purposes (ESP) is a relatively new concern in second language acquisition history. ESP has been defined as an approach to language teaching which tries to meet the needs of particular learners. Today, many educational institutions all over the world design English language programs and course...

  6. Conceptual design of Advanced Central Receiver Power Systems sodium-cooled receiver concept: development plan and pilot plant description. Final report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-03-01

    This volume encompasses Task 6 of the Phase I effort on the Advanced Central Receiver. This task included developing a plan to bring the commercial plant conceptual design into being. The base version of the plan includes a pilot plant to be designed and constructed during Phases II and III, three subsystem research experiments to be performed during Phase II, and the design and construction of a commercial demonstration plant. These plans are discussed in detail, as well as several options which could reduce both cost and schedule to achieve the overall goal of a commercial-sized demonstration plant. In evaluating pilot plant characeristics, emphasis was placed on representing commercial plant receiver characteristics and total system operation. In considering total system operation, it was recognized that a water-steam pilot plant would already be in operation, hence certain systems will already have been tested. Several receiver configurations were investigated consisting of from one to five full-size panels, with the objective of representing peak north side power for a 100-MWe plant as well as the peak flux vaue of about 1.4 MW/m/sup 2/. This goal was accomplished with a 5-panel receiver; however, the power to the edge panels is very low. Hence, with little loss, these panels can be eliminated to give a 3-panel configuration. The total absorbed thermal power is about 38 MWt, which is sufficient for about 10 MWe. A plant of this size is described.

  7. Design

    DEFF Research Database (Denmark)

    Volf, Mette

    This publication is unique in its demystification and operationalization of the complex and elusive nature of the design process. The publication portrays the designer’s daily work and the creative process, which the designer is a part of. Apart from displaying the designer’s work methods...... and design parameters, the publication shows examples from renowned Danish design firms. Through these examples the reader gets an insight into the designer’s reality....

  8. Electronics engineer's reference book

    CERN Document Server

    Mazda, F F

    1989-01-01

    Electronics Engineer's Reference Book, Sixth Edition is a five-part book that begins with a synopsis of mathematical and electrical techniques used in the analysis of electronic systems. Part II covers physical phenomena, such as electricity, light, and radiation, often met with in electronic systems. Part III contains chapters on basic electronic components and materials, the building blocks of any electronic design. Part IV highlights electronic circuit design and instrumentation. The last part shows the application areas of electronics such as radar and computers.

  9. Electroacoustical reference data

    CERN Document Server

    Eargle, John M

    2002-01-01

    The need for a general collection of electroacoustical reference and design data in graphical form has been felt by acousticians and engineers for some time. This type of data can otherwise only be found in a collection of handbooks. Therefore, it is the author's intention that this book serve as a single source for many electroacoustical reference and system design requirements. In form, the volume closely resembles Frank Massa's Acoustic Design Charts, a handy book dating from 1942 that has long been out of print. The basic format of Massa's book has been followed here: For each entry, graphical data are presented on the right page, while text, examples, and refer­ ences appear on the left page. In this manner, the user can solve a given problem without thumbing from one page to the next. All graphs and charts have been scaled for ease in data entry and reading. The book is divided into the following sections: A. General Acoustical Relationships. This section covers the behavior of sound transmis­ sion in...

  10. Nuclear reactor design

    CERN Document Server

    2014-01-01

    This book focuses on core design and methods for design and analysis. It is based on advances made in nuclear power utilization and computational methods over the past 40 years, covering core design of boiling water reactors and pressurized water reactors, as well as fast reactors and high-temperature gas-cooled reactors. The objectives of this book are to help graduate and advanced undergraduate students to understand core design and analysis, and to serve as a background reference for engineers actively working in light water reactors. Methodologies for core design and analysis, together with physical descriptions, are emphasized. The book also covers coupled thermal hydraulic core calculations, plant dynamics, and safety analysis, allowing readers to understand core design in relation to plant control and safety.

  11. Design and construction of a 55t/hour central coal grinding and drying plant at Laegerdorf. Description of chemical engineering and safety measures

    Energy Technology Data Exchange (ETDEWEB)

    Niemeyer, E.A.

    1979-09-01

    In order to save fuel oil in the cement industry, coal - along with lignite - is coming back into favour as an economical fuel. For conversion to coal firing at the Laegerdorf cement works a central grinding and drying plant for indirect firing and intermediate storage of pulverized coal is under construction. Imported coal of varying quality, from all parts of the world, is used. An air-swept mill will grind coal to a high degree of fineness at a rate of between 40 and 70 t/hour or mx. 330 000 t/year. The raw coal is handled under relatively dust-free conditions in a tipping installation for rail and road vehicles and is stored intermediately in concrete silos. The raw coal preparation system and the design features of the coaling plant and mill inlet are of decisive importance in ensuring a continuous and easy flow of coal even under difficult winter operating conditions. In feeding the mill it is necessary to have absolutely uniform and stable equilibrium between the input of moist raw coal and of not-too-hot drying air. By using two high-capacity cyclones the explosion hazard at the inlet to te electrostatic precipitator is reduced by lowering the dust concentration below the explosion limit. In designing coal grinding plants it is, in conjunction with attending to the process engineering and plant engineering features, necessary to have information on the explosion characteristics. Operational safety precautions against dust explosions or deflagrations constitute no more than ancillary protective measures. As no inert gas is available, active protection against explosion hazard is not practicable. For passive protection, the Laegerdorf pulverized coal plant is being built to explosion-proof, explosion-resistant and/or vented design standards, with type-tested explosion doors or blow-out panels; in addition, it is subdivided into two working areas 'inside' and 'outside' danger zones.

  12. Analysis and design of three dimensional supersonic nozzles. Volume 1: Nozzle-exhaust flow field analysis by a reference plane characteristics technique

    Science.gov (United States)

    Dash, S.; Delguidice, P.

    1972-01-01

    A second order numerical method employing reference plane characteristics has been developed for the calculation of geometrically complex three dimensional nozzle-exhaust flow fields, heretofore uncalculable by existing methods. The nozzles may have irregular cross sections with swept throats and may be stacked in modules using the vehicle undersurface for additional expansion. The nozzles may have highly nonuniform entrance conditions, the medium considered being an equilibrium hydrogen-air mixture. The program calculates and carries along the underexpansion shock and contact as discrete discontinuity surfaces, for a nonuniform vehicle external flow.

  13. Cotovelo flutuante em crianças: estudo descritivo de 31 casos atendidos em centro de referência em traumatologia pediátrica Floating elbow in children: a descriptive study of 31 cases attended in a reference center for pediatric trauma

    Directory of Open Access Journals (Sweden)

    Dorotea Starling Malheiros

    2011-10-01

    Full Text Available OBJETIVO: Realizar análise descritiva de 31 casos de crianças portadoras de cotovelo flutuante atendidas em nosso serviço no período de 1994 a 2009, bem como uma revisão da literatura pertinente ao tema. MÉTODOS: Os dados foram obtidos através da análise de prontuários. Foram consideradas as variáveis: idade, gênero, lado, mecanismo, tipo de fratura, classificação, tratamento e complicações. RESULTADOS: Vinte quatro pacientes (77,4% eram do gênero masculino e sete (22,6%, do feminino. A média de idade foi de 8,5 (± 3,2 que variaram entre um e 14 anos. Houve predomínio do lado esquerdo (67,7%. O mecanismo de lesão mais comum foi queda de altura (74,2%. Todas as fraturas supracondilianas foram do tipo III de Gartland. A fratura isolada do rádio distal do tipo II de Salter-Harris foi diagnosticada em 22 (71% pacientes. As fraturas expostas ocorreram em 22 pacientes (71%. A redução incruenta e gesso para fratura fechada do rádio distal foi realizada em dois pacientes (6,45%. O tratamento conservador simultâneo para ambas as fraturas não foi empregado. Dezessete (54,8% fraturas supracondilianas foram fixadas com fios cruzados a 90° e em 14 (45,16% utilizou-se um fio intramedular associado a outro introduzido pelo epicôndilo lateral a 45°. Quanto às complicações, houve: consolidação viciosa (10%, lesão nervosa (6%, síndrome compartimental (3%, infecção de trajeto de pinos (16%. Conclusões: Trata-se de uma lesão incomum, na maioria dos casos, decorrente de trauma de alta energia. O tratamento cirúrgico de ambas as fraturas é preconizado pela maioria dos autores. A lesão do nervo ulnar foi relacionada ao método de fixação, não havendo lesão neurológica desencadeada pelo trauma inicial.OBJECTIVE: To conduct a descriptive analysis on 31 cases of children with floating elbow who were attended at our clinic between 1994 and 2009, and to review the literature relating to this topic. METHODS: Data were obtained

  14. A Process Model for Developing Learning Design Patterns with International Scope

    Science.gov (United States)

    Lotz, Nicole; Law, Effie Lai-Chong; Nguyen-Ngoc, Anh Vu

    2014-01-01

    This paper investigates the process of identifying design patterns in international collaborative learning environments. In this context, design patterns are referred to as structured descriptions of best practice with pre-defined sections such as problem, solution and consequences. We pay special attention to how the scope of a design pattern is…

  15. Description of Measurements on Biogas Stations

    Directory of Open Access Journals (Sweden)

    Ladislav Novosád

    2016-08-01

    Full Text Available This paper focuses mainly on performance analysis for three biogas stations situated within the territory of the Czech Republic. This paper contains basic details of the individual biogas stations as well as description of their types. It also refers to the general description of the measurement gauge involved, with specifications of its potential use. The final part of this paper deals with the analysis of course data obtained, with special regard to voltage, current, active power and reactive power data.

  16. Framework for the design and delivery of organized physical activity sessions for children and adolescents: rationale and description of the 'SAAFE' teaching principles.

    Science.gov (United States)

    Lubans, David R; Lonsdale, Chris; Cohen, Kristen; Eather, Narelle; Beauchamp, Mark R; Morgan, Philip J; Sylvester, Benjamin D; Smith, Jordan J

    2017-02-23

    The economic burden of inactivity is substantial, with conservative estimates suggesting the global cost to health care systems is more than US$50 billion. School-based programs, including physical education and school sport, have been recommended as important components of a multi-sector, multi-system approach to address physical inactivity. Additionally, community sporting clubs and after-school programs (ASPs) offer further opportunities for young people to be physically active outside of school. Despite demonstrating promise, current evidence suggests school-based physical activity programs, community sporting clubs and ASPs are not achieving their full potential. For example, physical activity levels in physical education (PE) and ASP sessions are typically much lower than recommended. For these sessions to have the strongest effects on young people's physical activity levels and their on-going physical literacy, they need to improve in quality and should be highly active and engaging. This paper presents the Supportive, Active, Autonomous, Fair, Enjoyable (SAAFE) principles, which represent an evidence-based framework designed to guide the planning, delivery and evaluation of organized physical activity sessions in school, community sport and ASPs. In this paper we provide a narrative and integrative review of the conceptual and empirical bases that underpin this framework and highlight implications for knowledge translation and application.

  17. The "Performance of Rotavirus and Oral Polio Vaccines in Developing Countries" (PROVIDE) study: description of methods of an interventional study designed to explore complex biologic problems.

    Science.gov (United States)

    Kirkpatrick, Beth D; Colgate, E Ross; Mychaleckyj, Josyf C; Haque, Rashidul; Dickson, Dorothy M; Carmolli, Marya P; Nayak, Uma; Taniuchi, Mami; Naylor, Caitlin; Qadri, Firdausi; Ma, Jennie Z; Alam, Masud; Walsh, Mary Claire; Diehl, Sean A; Petri, William A

    2015-04-01

    Oral vaccines appear less effective in children in the developing world. Proposed biologic reasons include concurrent enteric infections, malnutrition, breast milk interference, and environmental enteropathy (EE). Rigorous study design and careful data management are essential to begin to understand this complex problem while assuring research subject safety. Herein, we describe the methodology and lessons learned in the PROVIDE study (Dhaka, Bangladesh). A randomized clinical trial platform evaluated the efficacy of delayed-dose oral rotavirus vaccine as well as the benefit of an injectable polio vaccine replacing one dose of oral polio vaccine. This rigorous infrastructure supported the additional examination of hypotheses of vaccine underperformance. Primary and secondary efficacy and immunogenicity measures for rotavirus and polio vaccines were measured, as well as the impact of EE and additional exploratory variables. Methods for the enrollment and 2-year follow-up of a 700 child birth cohort are described, including core laboratory, safety, regulatory, and data management practices. Intense efforts to standardize clinical, laboratory, and data management procedures in a developing world setting provide clinical trials rigor to all outcomes. Although this study infrastructure requires extensive time and effort, it allows optimized safety and confidence in the validity of data gathered in complex, developing country settings. © The American Society of Tropical Medicine and Hygiene.

  18. The “Performance of Rotavirus and Oral Polio Vaccines in Developing Countries” (PROVIDE) Study: Description of Methods of an Interventional Study Designed to Explore Complex Biologic Problems

    Science.gov (United States)

    Kirkpatrick, Beth D.; Colgate, E. Ross; Mychaleckyj, Josyf C.; Haque, Rashidul; Dickson, Dorothy M.; Carmolli, Marya P.; Nayak, Uma; Taniuchi, Mami; Naylor, Caitlin; Qadri, Firdausi; Ma, Jennie Z.; Alam, Masud; Walsh, Mary Claire; Diehl, Sean A.; Petri, William A.

    2015-01-01

    Oral vaccines appear less effective in children in the developing world. Proposed biologic reasons include concurrent enteric infections, malnutrition, breast milk interference, and environmental enteropathy (EE). Rigorous study design and careful data management are essential to begin to understand this complex problem while assuring research subject safety. Herein, we describe the methodology and lessons learned in the PROVIDE study (Dhaka, Bangladesh). A randomized clinical trial platform evaluated the efficacy of delayed-dose oral rotavirus vaccine as well as the benefit of an injectable polio vaccine replacing one dose of oral polio vaccine. This rigorous infrastructure supported the additional examination of hypotheses of vaccine underperformance. Primary and secondary efficacy and immunogenicity measures for rotavirus and polio vaccines were measured, as well as the impact of EE and additional exploratory variables. Methods for the enrollment and 2-year follow-up of a 700 child birth cohort are described, including core laboratory, safety, regulatory, and data management practices. Intense efforts to standardize clinical, laboratory, and data management procedures in a developing world setting provide clinical trials rigor to all outcomes. Although this study infrastructure requires extensive time and effort, it allows optimized safety and confidence in the validity of data gathered in complex, developing country settings. PMID:25711607

  19. Description and evaluation of a serious game intervention to engage low secure service users with serious mental illness in the design and refurbishment of their environment.

    Science.gov (United States)

    Fitzgerald, M M; Kirk, G D; Bristow, C A

    2011-05-01

    Service user involvement in all levels of healthcare provision is the expectation of UK government policy. Involvement should not only include participation in the planning and delivery of health care but also the exercise of choice and opinions about that care. In practice, however, service user engagement is most often tokenistic, involving post hoc consultation over plans already committed to by services. This paper explores an Occupational Therapy-led initiative to use the Serious Game format to engage low secure service users with serious mental illness in the design, layout and refurbishment of their unit. Among other things how medication was to be dispensed on the new unit was explored by this game and led to significant replanning in response to service user involvement. The game format was found to be a useful tool in facilitating communication between professionals and a traditionally marginalized and powerless client group. It enabled service users to have a voice, it provided a format for that voice to be heard and made possible service-led change in the planning process. © 2010 Blackwell Publishing.

  20. Optimal Conventional and Semi-Natural Treatments for the Upper Yakima Spring Chinook Salmon Supplementation Project; Treatment Definitions and Descriptions and Biological Specifications for Facility Design, 1995-1999 Final Report.

    Energy Technology Data Exchange (ETDEWEB)

    Hager, Robert C. (Hatchery Operations Consulting); Costello, Ronald J. (Mobrand Biometrics, Inc., Vashon Island, WA)

    1999-10-01

    This report describes the Yakima Fisheries Project facilities (Cle Elum Hatchery and acclimation satellites) which provide the mechanism to conduct state-of-the-art research for addressing questions about spring chinook supplementation strategies. The definition, descriptions, and specifications for the Yakima spring chinook supplementation program permit evaluation of alternative fish culture techniques that should yield improved methods and procedures to produce wild-like fish with higher survival that can be used to rebuild depleted spring chinook stocks of the Columbia River Basin. The definition and description of three experimental treatments, Optimal Conventional (OCT), Semi-Natural (SNT), Limited Semi-Natural (LSNT), and the biological specifications for facilities have been completed for the upper Yakima spring chinook salmon stock of the Yakima Fisheries Project. The task was performed by the Biological Specifications Work Group (BSWG) represented by Yakama Indian Nation, Washington Department of Fish and Wildlife, National Marine Fisheries Service, and Bonneville Power Administration. The control and experimental variables of the experimental treatments (OCT, SNT, and LSNT) are described in sufficient detail to assure that the fish culture facilities will be designed and operated as a production scale laboratory to produce and test supplemented upper Yakima spring chinook salmon. Product specifications of the treatment groups are proposed to serve as the generic templates for developing greater specificity for measurements of product attributes. These product specifications will be used to monitor and evaluate treatment effects, with respect to the biological response variables (post release survival, long-term fitness, reproductive success and ecological interactions).

  1. New design and facilities for the International Database for Absolute Gravity Measurements (AGrav): A support for the Establishment of a new Global Absolute Gravity Reference System

    Science.gov (United States)

    Wziontek, Hartmut; Falk, Reinhard; Bonvalot, Sylvain; Rülke, Axel

    2017-04-01

    After about 10 years of successful joint operation by BGI and BKG, the International Database for Absolute Gravity Measurements "AGrav" (see references hereafter) was under a major revision. The outdated web interface was replaced by a responsive, high level web application framework based on Python and built on top of Pyramid. Functionality was added, like interactive time series plots or a report generator and the interactive map-based station overview was updated completely, comprising now clustering and the classification of stations. Furthermore, the database backend was migrated to PostgreSQL for better support of the application framework and long-term availability. As comparisons of absolute gravimeters (AG) become essential to realize a precise and uniform gravity standard, the database was extended to document the results on international and regional level, including those performed at monitoring stations equipped with SGs. By this it will be possible to link different AGs and to trace their equivalence back to the key comparisons under the auspices of International Committee for Weights and Measures (CIPM) as the best metrological realization of the absolute gravity standard. In this way the new AGrav database accommodates the demands of the new Global Absolute Gravity Reference System as recommended by the IAG Resolution No. 2 adopted in Prague 2015. The new database will be presented with focus on the new user interface and new functionality, calling all institutions involved in absolute gravimetry to participate and contribute with their information to built up a most complete picture of high precision absolute gravimetry and improve its visibility. A Digital Object Identifier (DOI) will be provided by BGI to contributors to give a better traceability and facilitate the referencing of their gravity surveys. Links and references: BGI mirror site : http://bgi.obs-mip.fr/data-products/Gravity-Databases/Absolute-Gravity-data/ BKG mirror site: http

  2. Design and implementation of a wireless (Bluetooth) four channel bio-instrumentation amplifier and digital data acquisition device with user-selectable gain, frequency, and driven reference.

    Science.gov (United States)

    Cosmanescu, Alin; Miller, Benjamin; Magno, Terence; Ahmed, Assad; Kremenic, Ian

    2006-01-01

    A portable, multi-purpose Bio-instrumentation Amplifier and Data AcQuisition device (BADAQ) capable of measuring and transmitting EMG and EKG signals wirelessly via Bluetooth is designed and implemented. Common topologies for instrumentation amplifiers and filters are used and realized with commercially available, low-voltage, high precision operational amplifiers. An 8-bit PIC microcontroller performs 10-bit analog-to-digital conversion of the amplified and filtered signals and controls a Bluetooth transceiver capable of wirelessly transmitting the data to any Bluetooth enabled device. Electrical isolation between patient/subject, circuitry, and ancillary equipment is achieved by optocoupling components. The design focuses on simplicity, portability, and affordability.

  3. Direct or Directed: Orchestrating a More Harmonious Approach to Teaching Technology within an Art & Design Higher Education Curriculum with Special Reference to Visual Communications Courses

    Science.gov (United States)

    Marshall, Lindsey; Meachem, Lester

    2007-01-01

    In this scoping study we have investigated the integration of subject-specific software into the structure of visual communications courses. There is a view that the response within visual communications courses to the rapid developments in technology has been linked to necessity rather than by design. Through perceptions of staff with day-to-day…

  4. A prospective study of symptoms, function, and medication use during acute illness in nursing home residents: design, rationale and cohort description

    Directory of Open Access Journals (Sweden)

    Liu Sophia

    2010-07-01

    incidence of 1.5 (SD 2.0 episodes per resident per year; 74% were managed in the nursing home and 26% managed in the acute care setting. Conclusion In this report, we describe the conceptual model and methods of designing a longitudinal cohort to measure acute illness patterns and symptoms among nursing home residents, and describe the characteristics of our cohort at baseline. In our planned analysis, we will further estimate the effect of the use and interruption of medications on withdrawal and relapse symptoms and illness outcomes.

  5. A description of the demographic characteristics of the New Zealand non-commercial horse population with data collected using a generalised random-tessellation stratified sampling design.

    Science.gov (United States)

    Rosanowski, S M; Cogger, N; Rogers, C W; Benschop, J; Stevenson, M A

    2012-12-01

    We conducted a cross-sectional survey to determine the demographic characteristics of non-commercial horses in New Zealand. A sampling frame of properties with non-commercial horses was derived from the national farms database, AgriBase™. Horse properties were stratified by property size and a generalised random-tessellated stratified (GRTS) sampling strategy was used to select properties (n=2912) to take part in the survey. The GRTS sampling design allowed for the selection of properties that were spatially balanced relative to the distribution of horse properties throughout the country. The registered decision maker of the property, as identified in AgriBase™, was sent a questionnaire asking them to describe the demographic characteristics of horses on the property, including the number and reason for keeping horses, as well as information about other animals kept on the property and the proximity of boundary neighbours with horses. The response rate to the survey was 38% (1044/2912) and the response rate was not associated with property size or region. A total of 5322 horses were kept for recreation, competition, racing, breeding, stock work, or as pets. The reasons for keeping horses and the number and class of horses varied significantly between regions and by property size. Of the properties sampled, less than half kept horses that could have been registered with Equestrian Sports New Zealand or either of the racing codes. Of the respondents that reported knowing whether their neighbours had horses, 58.6% (455/776) of properties had at least one boundary neighbour that kept horses. The results of this study have important implications for New Zealand, which has an equine population that is naïve to many equine diseases considered endemic worldwide. The ability to identify, and apply accurate knowledge of the population at risk to infectious disease control strategies would lead to more effective strategies to control and prevent disease spread during an

  6. Towards a Pattern Language Approach to Document Description

    Directory of Open Access Journals (Sweden)

    Robert Waller

    2012-07-01

    Full Text Available Pattern libraries, originating in architecture, are a common way to share design solutions in interaction design and software engineering. Our aim in this paper is to consider patterns as a way of describing commonly-occurring document design solutions to particular problems, from two points of view. First, we are interested in their use as exemplars for designers to follow, and second, we suggest them as a means of understanding linguistic and graphical data for their organization into corpora that will facilitate descriptive work. We discuss the use of patterns across a range of disciplines before suggesting the need to place patterns in the context of genres, with each potentially belonging to a “home genre” in which it originates and to which it makes an implicit intertextual reference intended to produce a particular reader response in the form of a reading strategy or interpretative stance. We consider some conceptual and technical issues involved in the descriptive study of patterns in naturally-occurring documents, including the challenges involved in building a document corpus.

  7. Xcode 5 developer reference

    CERN Document Server

    Wentk, Richard

    2014-01-01

    Design, code, and build amazing apps with Xcode 5 Thanks to Apple's awesome Xcode development environment, you can create the next big app for Macs, iPhones, iPads, or iPod touches. Xcode 5 contains gigabytes of great stuff to help you develop for both OS X and iOS devices - things like sample code, utilities, companion applications, documentation, and more. And with Xcode 5 Developer Reference, you now have the ultimate step-by-step guide to it all. Immerse yourself in the heady and lucrative world of Apple app development, see how to tame the latest features and functions, and find loads of

  8. Design

    DEFF Research Database (Denmark)

    Volf, Mette

    Design - proces & metode iBog®  er enestående i sit fokus på afmystificering og operationalisering af designprocessens flygtige og komplekse karakter. Udgivelsen går bag om designerens daglige arbejde og giver et indblik i den kreative skabelsesproces, som designeren er en del af. Udover et bredt...... indblik i designerens arbejdsmetoder og designparametre giver Design - proces & metode en række eksempler fra anerkendte designvirksomheder, der gør det muligt at komme helt tæt på designerens virkelighed....

  9. Design development scopes towards occupational wellness of women workers: specific reference to local agro based food processing industries in NE India.

    Science.gov (United States)

    Bhattacharyya, Nandita; Chakrabarti, Debkumar

    2012-01-01

    Women workers constitute one of the most vulnerable segments of the country's labour force. They often face different workplace health challenges than men do. They are engaged in a range of work that extends from heavy, monotonous, repetitive jobs, which are in many times experienced with low-paid and involves in long hours of work. Women's workplace health problems are frequently compounded by getting more of the same at home--the "double jeopardy" of domestic work. Specific issues to improve the workers motivation leading to enhancement of productivity and improving occupational health and safety were addressed. Context specific application of ergonomics principles were studied in the process of designing of work related equipment of local fruit processing units, as well as in tea industry, covering 180 subjects selected purposively. Ergonomic risk factors prevailed among the workers associates productivity and relevant health issues were quantified using QEC, RULA. NMQ was used to gather data on prevalence of CTDs among the workers. Pineapple peeling, tea leaves plucking were found highly labour intensive, done manually. Postures scores found were very high. WRMSDs were prevalent among the workers. Scope for ergonomic design intervention was observed to improve productivity and occupational health.

  10. Design

    Science.gov (United States)

    Buchanan, Richard; Cross, Nigel; Durling, David; Nelson, Harold; Owen, Charles; Valtonen, Anna; Boling, Elizabeth; Gibbons, Andrew; Visscher-Voerman, Irene

    2013-01-01

    Scholars representing the field of design were asked to identify what they considered to be the most exciting and imaginative work currently being done in their field, as well as how that work might change our understanding. The scholars included Richard Buchanan, Nigel Cross, David Durling, Harold Nelson, Charles Owen, and Anna Valtonen. Scholars…

  11. A DESCRIPTIVE INDONESIAN GRAMMAR--PRELIMINARY EDITION.

    Science.gov (United States)

    DYEN, ISIDORE

    THIS PRELIMINARY EDITION COMPRISES A DESCRIPTIVE GRAMMAR OF INDONESIAN (BAHASA INDONESIA), THE OFFICIAL LANGUAGE OF THE REPUBLIC OF INDONESIA. THE THREE SECTIONS--PHONOLOGY, SYNTAX, AND MORPHOLOGY--PRESENT A COMPREHENSIVE LINGUISTIC ANALYSIS OF INDONESIAN, WITH OCCASIONAL CONTRASTIVE REFERENCE TO MALAY, JAVANESE, SUNDANESE, AND SUMATRAN. THIS…

  12. Design Description Document for PLANIT System Enhancements

    Science.gov (United States)

    1977-04-01

    4 A-3.0 TERMINAL RIAD AND WRITE RESPONSES A-5 A-3.1 PLANIT Read A-5 A-3.1.1 ACC/OCC Read A-5 A_3.1.2 VFMED/MIOD Read A-6 A-3.2 PLANIT Write A-7 B...combination of the two oririnal aproaches and is described in ApDendix A. Table I-I shows the PLANIP WIVMON items which will be referenced by "-CF -or full...comane error. This will be done by returnine a -1 status "or the terminal write reauest. 3-1 T ABLE 3-1. "(1OP RRENCED PLANTT7 -’OWAN rTEř ITEM NA

  13. Description logics of context

    CSIR Research Space (South Africa)

    Klarman, S

    2013-05-01

    Full Text Available We introduce Description Logics of Context (DLCs) - an extension of Description Logics (DLs) for context-based reasoning. Our approach descends from J. McCarthy's tradition of treating contexts as formal objects over which one can quantify...

  14. Descriptive set theory

    CERN Document Server

    Moschovakis, YN

    1987-01-01

    Now available in paperback, this monograph is a self-contained exposition of the main results and methods of descriptive set theory. It develops all the necessary background material from logic and recursion theory, and treats both classical descriptive set theory and the effective theory developed by logicians.

  15. Ignoring Grounded Description

    Directory of Open Access Journals (Sweden)

    Barney G. Glaser, PhD, Hon. PhD

    2016-12-01

    Full Text Available Why is there so much grounded description? The simplest, direct answer is that to many a researcher this is GT. This view is supported by several factors. It is easy and natural to describe accurately. So slipping into grounded description comes naturally and is ok as GT. Also departmental support for description is strongly supported by perspective and academic rewards and history and routine QDA. Also many researchers and readers of research cannot conceptualize very well if at all. They want accurate description about the data in the study. They are not into taking a core category as a general category applicable to general implications applicable to much data elsewhere. Their study is about explaining processes the data, NOT in studying the implications of core and sub-core categories as they are integrated into an explanatory theory. I trust the reader can think of other sources of letting GT research slip into conceptual description.

  16. Hanford Environmental Information System (HEIS). Volume 3, Subject Area reference manual

    Energy Technology Data Exchange (ETDEWEB)

    Schreck, R.I.

    1994-01-14

    The Hanford Environmental Information System (HEIS) Subject Area manuals are designed as reference guides, that is, each chapter provides the information needed to make best use of each subject area, its tables, and reporting capabilities. Each subject area is documented in a chapter in one of the subject area manuals. Because these are reference manuals, most of the information is also available in the online help system as well. See Section 5.4.2 of the HEIS User`s Guide (DOE-RL 1994a) for a detailed description of the online help.

  17. Irrigation Training Manual. Planning, Design, Operation, and Management of Small-Scale Irrigation Systems [and] Irrigation Reference Manual. A Technical Reference to Be Used with the Peace Corps Irrigation Training Manual T0076 in the Selection, Planning, Design, Operation, and Management of Small-Scale Irrigation Systems.

    Science.gov (United States)

    Salazar, LeRoy; And Others

    This resource for trainers involved in irrigated agriculture training for Peace Corps volunteers consists of two parts: irrigation training manual and irrigation reference manual. The complete course should fully prepare volunteers serving as irrigation, specialists to plan, implement, evaluate and manage small-scale irrigation projects in arid,…

  18. Definition, design, utilization. Some problems associated with Integrated Science curricula with special reference to the Project for Science Integration in Ghana

    Science.gov (United States)

    Lutterodt, S. A.

    1981-09-01

    The rapid spread of Integrated Science Courses throughout the world should not conceal the difficulties facing teachers in utilizing Integrated Science curricula. These problems derive from lack of precision in definition and give rise to basic tensions between scientific and educational principles in course design. Learning by discovery approaches, applied to the pupil's level of intellectual development, have to bridge the gap between knowledge from everyday experience and an articulated appreciation of the unity of science. The contrasting environments which condition everyday experience complicate the resolution of these problems. Three kinds of `dilemma' in teachers' utilizing of Integrated Science curricula are identified from the evaluation of `Project for Science Integration' in Ghana: (1) how far experience can be incorporated before beginning to sacrifice conceptual unity; (2) how pupils' understanding of the theoretical implications of practical activities can be achieved; and (3) how the varying results of individual pupils' experience can be adapted to the successful teaching of prescribed objectives. These dilemmas exemplify the need for a realistic assessment of the experience of Integrated Science teaching over the last decade, leading to more conceptual precision, a greater awareness of curricular possibilities, and more enlightened decision-making.

  19. Gas phase bio-filter for the removal of triethylamine (TEA) from air: microbial diversity analysis with reference to design parameters.

    Science.gov (United States)

    Gandu, Bharath; Sandhya, K; Gangagni Rao, A; Swamy, Y V

    2013-07-01

    Biotic (packed bio-filter; PBF) and abiotic (packed filter; PF) studies were carried out on two similar 2L gas phase filters for the removal of triethylamine (TEA) at inlet concentration in the range of 250-280 ppmV. Removal efficiency (RE) of PBF remained in the range of 90-99% during the stable period of operation (170 days) whereas RE of PF dropped gradually to 10% in a span of 90 days. Five different bacterial species viz; Aeromonas sp., Alcaligenes sp., Arthrobacter sp., Klebsiella sp., and Pseudomonas sp., were identified in PBF. It was observed that diethyl amine, ethylamine and nitrate were formed as metabolites during the degradation pathway. Empty bed residence time of 20s, mass loading rate of 202.26 g/m(3)/h, space velocity of 178.82 m(3)/m(3)/h and elimination capacity of 201.52 g/m(3)/h were found to be optimum design parameters for PBF to get RE in the range of 90-99%. Copyright © 2013 Elsevier Ltd. All rights reserved.

  20. Reference Librarian in Digital Environment:

    Directory of Open Access Journals (Sweden)

    Faramarz Sohili

    2008-07-01

    Full Text Available The information explosion of the latter half of the twentieth century, gave rise to online databases and various information media that gradually impacted on the very physical environment of the library. It transformed the librarians’ role. Reference librarians are no exception. The present study aims to investigate the need or lack of need to reference librarians within the digital domains based on the views expressed by LIS authorities in Iran. It would attempt further, to identify the qualities required for such librarian should a need for her/his expressed. The research, while descriptive in nature, was based on analyzing the results obtained by the checklist devised by the authors. LIS Specialist sample was composed of 57 people who filled the checklist. Findings show that there is a significance between employing ICT and need for a reference librarian. LIS experts in Iran believe that introduction of ICT, especially Internet and the WWW not only didn’t decrease the need for such librarians, but has caused the reference librarian to attain a more important and better status than before. Findings further demonstrated that while Iran is not a signatory to the international copyright conventions, the Iranian reference librarians are fully committed to observing author’s copyright and intellectual rights and frown on using software crackers.

  1. Forsmark - site descriptive model version 0

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-10-01

    area identified in the feasibility study as favourable for further study. This rectangular area has now been designated the Forsmark regional model area. An important component of the present work is a data inventory, in which the location and scope of all potential sources of data is detailed and evaluated with respect to prospective usefulness for future site descriptive modelling for deep disposal. Data sources relevant to the Forsmark regional model area which still, to some degree, need to be evaluated/converted/inserted include the siting and construction of the three nuclear reactors (Forsmark 1-3), the feasibility study for an underground spent nuclear fuel interim storage facility at Forsmark, the pre-investigations and construction of the SFR, and the SAFE project. The present report describes the current level of knowledge of the surface ecosystems in the Forsmark regional model area, in a highly condensed form. It refers to, and draws its examples from, a series of SKB background reports which have been produced since the completion of the Oesthammar feasibility study, and a number of other sources of information which are gathered here for the first time. The data sources are outlined with reference to a series of functional ecosystem types: drainage areas, forest, wetland, agricultural land, lakes and rivers, and sea, each further subdivided into appropriate entities. A systematic approach has been used, even though, at the current level of knowledge, the information in many subdivisions is inadequate or lacking. The aims of biosphere studies within the site investigation programme are to define baseline (preconstruction) conditions, to provide the necessary data base for the environmental impact statement, and to contribute to the dose estimations in the safety analysis. The main emphasis of the report is on the preparation of a site descriptive model, version 0, for the geosphere, since data acquisition and processing in this area, in contrast to the

  2. Definition and Proposed Realization of the International Height Reference System (IHRS)

    Science.gov (United States)

    Ihde, Johannes; Sánchez, Laura; Barzaghi, Riccardo; Drewes, Hermann; Foerste, Christoph; Gruber, Thomas; Liebsch, Gunter; Marti, Urs; Pail, Roland; Sideris, Michael

    2017-05-01

    Studying, understanding and modelling global change require geodetic reference frames with an order of accuracy higher than the magnitude of the effects to be actually studied and with high consistency and reliability worldwide. The International Association of Geodesy, taking care of providing a precise geodetic infrastructure for monitoring the Earth system, promotes the implementation of an integrated global geodetic reference frame that provides a reliable frame for consistent analysis and modelling of global phenomena and processes affecting the Earth's gravity field, the Earth's surface geometry and the Earth's rotation. The definition, realization, maintenance and wide utilization of the International Terrestrial Reference System guarantee a globally unified geometric reference frame with an accuracy at the millimetre level. An equivalent high-precision global physical reference frame that supports the reliable description of changes in the Earth's gravity field (such as sea level variations, mass displacements, processes associated with geophysical fluids) is missing. This paper addresses the theoretical foundations supporting the implementation of such a physical reference surface in terms of an International Height Reference System and provides guidance for the coming activities required for the practical and sustainable realization of this system. Based on conceptual approaches of physical geodesy, the requirements for a unified global height reference system are derived. In accordance with the practice, its realization as the International Height Reference Frame is designed. Further steps for the implementation are also proposed.

  3. WASTE PACKAGE TRANSPORTER DESIGN

    Energy Technology Data Exchange (ETDEWEB)

    D.C. Weddle; R. Novotny; J. Cron

    1998-09-23

    The purpose of this Design Analysis is to develop preliminary design of the waste package transporter used for waste package (WP) transport and related functions in the subsurface repository. This analysis refines the conceptual design that was started in Phase I of the Viability Assessment. This analysis supports the development of a reliable emplacement concept and a retrieval concept for license application design. The scope of this analysis includes the following activities: (1) Assess features of the transporter design and evaluate alternative design solutions for mechanical components. (2) Develop mechanical equipment details for the transporter. (3) Prepare a preliminary structural evaluation for the transporter. (4) Identify and recommend the equipment design for waste package transport and related functions. (5) Investigate transport equipment interface tolerances. This analysis supports the development of the waste package transporter for the transport, emplacement, and retrieval of packaged radioactive waste forms in the subsurface repository. Once the waste containers are closed and accepted, the packaged radioactive waste forms are termed waste packages (WP). This terminology was finalized as this analysis neared completion; therefore, the term disposal container is used in several references (i.e., the System Description Document (SDD)) (Ref. 5.6). In this analysis and the applicable reference documents, the term ''disposal container'' is synonymous with ''waste package''.

  4. On Meanings and Descriptions

    Directory of Open Access Journals (Sweden)

    Mieke Bal

    1981-09-01

    Full Text Available Although descriptive passages would appear to be of marginal importance in narrative texts, they are, in fact, of both logical and semantic necessity. Narratology, therefore, must take these segments into account. In this article, I shall survey the present situation in this field and compare rival points of view. I shall also offer several suggestions for analyzing descriptions. The following topics will be discussed: the nature of description as a specific type of discourse which makes it recognizable as such; the internal structure of description; the place and function of descriptions in the text as a whole. In the latter section, the semantic impact of descriptions in the overall meaning of narrative texts will be accounted for. This article is intended as a contribution to the theory of description as a part of narratology. It also has a didactic purpose, since it proposes a model for the analysis of texts which can be used for systematic text-study, both in a historical and a comparative perspective.

  5. Open Coding Descriptions

    Directory of Open Access Journals (Sweden)

    Barney G. Glaser, PhD, Hon PhD

    2016-12-01

    Full Text Available Open coding is a big source of descriptions that must be managed and controlled when doing GT research. The goal of generating a GT is to generate an emergent set of concepts and their properties that fit and work with relevancy to be integrated into a theory. To achieve this goal, the researcher begins his research with open coding, that is coding all his data in every possible way. The consequence of this open coding is a multitude of descriptions for possible concepts that often do not fit in the emerging theory. Thus in this case the researcher ends up with many irrelevant descriptions for concepts that do not apply. To dwell on descriptions for inapplicable concepts ruins the GT theory as it starts. It is hard to stop. Confusion easily sets in. Switching the study to a QDA is a simple rescue. Rigorous focusing on emerging concepts is vital before being lost in open coding descriptions. It is important, no matter how interesting the description may become. Once a core is possible, selective coding can start which will help control against being lost in multiple descriptions.

  6. Generic Argillite/Shale Disposal Reference Case

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Liange; Colon, Carlos Jové; Bianchi, Marco; Birkholzer, Jens

    2014-08-08

    Radioactive waste disposal in a deep subsurface repository hosted in clay/shale/argillite is a subject of widespread interest given the desirable isolation properties, geochemically reduced conditions, and widespread geologic occurrence of this rock type (Hansen 2010; Bianchi et al. 2013). Bianchi et al. (2013) provides a description of diffusion in a clay-hosted repository based on single-phase flow and full saturation using parametric data from documented studies in Europe (e.g., ANDRA 2005). The predominance of diffusive transport and sorption phenomena in this clay media are key attributes to impede radionuclide mobility making clay rock formations target sites for disposal of high-level radioactive waste. The reports by Hansen et al. (2010) and those from numerous studies in clay-hosted underground research laboratories (URLs) in Belgium, France and Switzerland outline the extensive scientific knowledge obtained to assess long-term clay/shale/argillite repository isolation performance of nuclear waste. In the past several years under the UFDC, various kinds of models have been developed for argillite repository to demonstrate the model capability, understand the spatial and temporal alteration of the repository, and evaluate different scenarios. These models include the coupled Thermal-Hydrological-Mechanical (THM) and Thermal-Hydrological-Mechanical-Chemical (THMC) models (e.g. Liu et al. 2013; Rutqvist et al. 2014a, Zheng et al. 2014a) that focus on THMC processes in the Engineered Barrier System (EBS) bentonite and argillite host hock, the large scale hydrogeologic model (Bianchi et al. 2014) that investigates the hydraulic connection between an emplacement drift and surrounding hydrogeological units, and Disposal Systems Evaluation Framework (DSEF) models (Greenberg et al. 2013) that evaluate thermal evolution in the host rock approximated as a thermal conduction process to facilitate the analysis of design options. However, the assumptions and the

  7. Standard Reference Tables -

    Data.gov (United States)

    Department of Transportation — The Standard Reference Tables (SRT) provide consistent reference data for the various applications that support Flight Standards Service (AFS) business processes and...

  8. Descriptive Data of Patients with Venous Thromboembolism

    Directory of Open Access Journals (Sweden)

    Gul Ilhan

    2013-08-01

    Full Text Available Purpose: This study was designed for collecting descriptive data about diagnosis and treatment of patients diagnosed with venous thromboembolism (VTE in an university hospital and for reflecting approach to VTE in such a reference hospital in this way. Material and Methods: We evaluated archive records of patients disgnosed with deep vein thrombosis (DVT and pulmonary thromboembolism (PTE between 2000 an 2005. Age average of patients was advanced and most of them were women. They had DVT, PTE, DVT and PTE respectively. Most common diagnostic method used for PTE was computed thomogrphy (CT, for DVT was ultrasonography (USG. VTE was diagnosed most frequently in emergency services and policlinics. Most common chronic risk factors for VTE were cancer, heart failure/romathismal cardiac disease, hyperlipidemia/atherosclerosis and obesity. Risk factors spesific to the attacks (or temporary were immobilization, surgery, pregnancy, taking oral contraseptive drugs and trauma. Results: In patients investigated for hemostatic risk factors, Factor V Leiden, Prothrombin 20210 A , and MTHFR mutations were found respectively. Symptoms and findings of patients admitted with PTE were dyspnea-tachipnea, tachycardia, palpitation, pleural pain, caugh, fever, anginal pain, hemopthysis, diaphoresis and wheezing . Echocardiography gave positive results for the most of PTE cases. D-dimer test was found high sensitive. Treatments during accute attacks were low moleculer weight heparin (LMWH, standart heparin, thrombolytic therapy, surgery, aspirine and vena cava inferior filter placement. Acute term complications were death, bleeding and heparin induced thrombocytopenia. Conclusion: This retrospective study reflects the approach of VTE diagnosis and treatment in a reference hospital and it may guide for prospective studies. [Cukurova Med J 2013; 38(4.000: 610-616

  9. Physics within a quantum reference frame

    Energy Technology Data Exchange (ETDEWEB)

    Angelo, Renato M [Federal University of Parana, PO Box 19044, 81531-990, Curitiba, PR (Brazil); Brunner, Nicolas; Popescu, Sandu; Skrzypczyk, Paul [H H Wills Physics Laboratory, University of Bristol, Tyndall Avenue, Bristol, BS8 1TL (United Kingdom); Short, Anthony J, E-mail: renato@fisica.ufpr.br [DAMTP, Centre for Mathematical Sciences, Wilberforce Road, Cambridge, CB3 0WA (United Kingdom)

    2011-04-08

    We investigate the physics of quantum reference frames. Specifically, we study several simple scenarios involving a small number of quantum particles, whereby we promote one of these particles to the role of a quantum observer and ask what is the description of the rest of the system, as seen by this observer? We highlight the interesting aspects of such questions by presenting a number of apparent paradoxes. By unravelling these paradoxes, we obtain a better understanding of the physics of quantum reference frames.

  10. Participatory Scenario Generation: Communicating Usability Issues in Product Design through User Involvement in Scenario Generation

    NARCIS (Netherlands)

    van der Bijl-Brouwer, Mieke; van der Voort, Mascha C.

    2009-01-01

    Scenarios have proven to be a valuable tool in evaluating and communicating usability issues in consumer product design. Scenarios are explicit descriptions of hypothetical use situations. Realistic scenarios can serve as a valuable frame of reference to evaluate design solutions with regard to

  11. Description of vegetation types

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This document provides descriptions of five vegetation types found in Iowa- oak savannah, mature hardwoods, floodplain woods, scrub woods, and riparian woods. Oak...

  12. Technical reference book for the Energy Economic Data Base (EEDB) Program

    Energy Technology Data Exchange (ETDEWEB)

    Allen, R.E.; Benedict, R.G.; Hodson, J.S.

    1984-09-01

    The Energy Economic Data Base (EEDB) Program is sponsored by the US Department of Energy (DOE) for the purpose of developing current technical and cost information for nuclear and comparison electric power generating stations. The EEDB contains a variety of nuclear and coal-fired power plant technical data models. Each of these data models is a complete and detailed conceptual design for a single unit, commercial, steam electric, power generating station located on a standard hypothetical Middletown site. A major effort for the Sixth Update (1983) has been the updating of the system design descriptions and selected engineering drawings for the technical data models. This update took the form of revising and expanding the system design descriptions and engineering drawings contained in the Base Data Studies, to include the technical information developed and recorded in the first five EEDB updates. The results of the update effort are contained in this EEDB Program Technical Reference Book.

  13. Descriptive sensory evaluations

    DEFF Research Database (Denmark)

    Dehlholm, Christian

    . The new methods were compared to the Flash Profile, Napping and conventional descriptive profiling. Furthermore, an approach for applying confidence ellipses to Multiple Factor Analysis (MFA) results from the statistical package R were suggested for the graphical validation and comparisons. PN allowed...... descriptive methodology is proposed and, based on the findings and evaluations of the studies, a concept scale that combines holistic and analytic assessor responses is proposed for future evaluations....

  14. LISA Gravitational Reference Sensors

    Energy Technology Data Exchange (ETDEWEB)

    Sun Kexun [Ginzton Laboratory, Stanford University, Stanford, CA 94305 (United States); Johann, Ulrich [EADS Astrium GmbH, Immenstaad (Germany); DeBra, Dan B; Buchman, Sasha [Ginzton Laboratory, Stanford University, Stanford, CA 94305 (United States); Byer, Robert L [Ginzton Laboratory, Stanford University, Stanford, CA 94305 (United States)

    2007-03-15

    We review state of the art of the gravitational reference sensor (GRS) for the Laser Interferometer Space Antenna (LISA). LISA consists of three identical spacecraft placed at the corners of an equilateral triangle with a 5 million kilometer baseline. In the LISA baseline design, the spacecraft at each corner will have two optical assemblies subtending an angle of 60 degrees. A proof mass (PM) is housed in a GRS located at the center of each assembly. LISA measures the distance variation between PMs separated by 5 million kilometers to a precision of 40 pm/Hz{sup 1/2}. The GRS must shield the PM from external disturbances such as solar wind and functions as a drag-free sensor for spacecraft control. The GRS must minimize the back action and cross talk exerted by measurements themselves. Significant progress has been made in the design, fabrication and testing of the GRS. LISA Pathfinder will fly a test GRS system scheduled around 2009. In addition, there have also been new architectures proposed to simplify the LISA payloads by using a single PM and therefore only one GRS per spacecraft. Further a modular GRS (MGRS) structure is proposed to reduce complexity. Optical sensing and large gap size between the PM and the MGRS housing are proposed to lower the disturbance level. Many experimental, engineering design, and trade off studies are underway.

  15. 3 GeV Injector Design Handbook

    Energy Technology Data Exchange (ETDEWEB)

    Wiedemann, H.; /SLAC, SSRL

    2009-12-16

    This Design Handbook is intended to be the main reference book for the specifications of the 3 GeV SPEAR booster synchrotron project. It is intended to be a consistent description of the project including design criteria, key technical specifications as well as current design approaches. Since a project is not complete till it's complete changes and modifications of early conceptual designs must be expected during the duration of the construction. Therefore, this Design Handbook is issued as a loose leaf binder so that individual sections can be replaced as needed. Each page will be dated to ease identification with respect to latest revisions. At the end of the project this Design Handbook will have become the 'as built' reference book of the injector for operations and maintenance personnel.

  16. Korean Reference HLW Disposal System

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Heui Joo; Lee, J. Y.; Kim, S. S. (and others)

    2008-03-15

    This report outlines the results related to the development of Korean Reference Disposal System for High-level radioactive wastes. The research has been supported around for 10 years through a long-term research plan by MOST. The reference disposal method was selected via the first stage of the research during which the technical guidelines for the geological disposal of HLW were determined too. At the second stage of the research, the conceptual design of the reference disposal system was made. For this purpose the characteristics of the reference spent fuels from PWR and CANDU reactors were specified, and the material and specifications of the canisters were determined in term of structural analysis and manufacturing capability in Korea. Also, the mechanical and chemical characteristics of the domestic Ca-bentonite were analyzed in order to supply the basic design parameters of the buffer. Based on these parameters the thermal and mechanical analysis of the near-field was carried out. Thermal-Hydraulic-Mechanical behavior of the disposal system was analyzed. The reference disposal system was proposed through the second year research. At the final third stage of the research, the Korean Reference disposal System including the engineered barrier, surface facilities, and underground facilities was proposed through the performance analysis of the disposal system.

  17. Virtual Reference Interferometry: Theory & Experiment

    Science.gov (United States)

    Galle, Michael Anthony

    This thesis introduces the idea that a simulated interferogram can be used as a reference for an interferometer. This new concept represents a paradigm shift from the conventional thinking, where a reference is the phase of a wavefront that traverses a known path. The simulated interferogram used as a reference is called a virtual reference. This thesis develops the theory of virtual reference interferometry and uses it for the characterization of chromatic dispersion in short length (design to nonlinear photonics, sensing and communications. Techniques for short-length dispersion characterization are therefore critical to the development of many photonic systems. The current generation of short-length dispersion measurement techniques are either easy to operate but lack sufficient accuracy, or have sufficient accuracy but are difficult to operate. The use of a virtual reference combines the advantages of these techniques so that it is both accurate and easy to operate. Chromatic dispersion measurements based on virtual reference interferometry have similar accuracy as the best conventional measurement techniques due to the ability to measure first and second order dispersion directly from the interference pattern. Unique capabilities of virtual reference interferometry are demonstrated, followed by a derivation of the operational constraints and system parameters. The technique is also applied to the characterization of few-mode fibers, a hot topic in telecommunications research where mode division multiplexing promises to expand network bandwidth. Also introduced is the theory of dispersive virtual reference interferometry, which can be used to overcome the bandwidth limitations associated with the measurement of near-zero dispersion-length optical components via compression of the interference pattern. Additionally, a method for utilizing the virtual reference interferometer in a low-coherence setup is introduced, enabling characterization in new wavelength

  18. Fundamentals of Reference

    Science.gov (United States)

    Mulac, Carolyn M.

    2012-01-01

    The all-in-one "Reference reference" you've been waiting for, this invaluable book offers a concise introduction to reference sources and services for a variety of readers, from library staff members who are asked to work in the reference department to managers and others who wish to familiarize themselves with this important area of…

  19. Generating descriptive statistics from the MXFLS

    OpenAIRE

    Alicia Santana Cartas

    2010-01-01

    In this presentation, I aim to show how to produce informative descriptive statistics from a longitudinal survey using the Mexican Family Life Survey (MXFLS) as an example. I will introduce the audience to the MXFLS and discuss its main innovative features, such as the sample design, the attitudes toward the risk module, and the migration module (including the monitoring and rate of recontact). Then I will show how to tabulate the data in an informative way and how to produce descriptive stat...

  20. Description of the RDCDS Meteorological Component

    Energy Technology Data Exchange (ETDEWEB)

    Pekour, Mikhail S.; Berg, Larry K.

    2007-10-01

    This report provides a detailed description of the Rapidly Deployable Chemical Defense System (RDCDS) Meteorological Component. The Meteorological Component includes four surface meteorological stations, miniSODAR, laptop computers, and communications equipment. This report describes the equipment that is used, explains the operation of the network, and gives instructions for setting up the Component and replacing defective parts. A detailed description of operation and use of the individual sensors, including the data loggers is not covered in the current document, and the interested reader should refer to the manufacturer’s documentation.

  1. A Basic Reference Grammar of Slovene.

    Science.gov (United States)

    Derbyshire, William W.

    This reference grammar is intended for adult speakers of English who are at the elementary through the intermediate levels of acquisition of the Slovene language. It begins with a brief description of the Slovene language, its major dialects and its place among the Slavic languages. Information on the alphabet, pronunciation, and spelling rules…

  2. Preventing Sexual Abuse. Reference Sheet 8.

    Science.gov (United States)

    Britton, Patti O., Ed.; McGee, Michael, Ed.

    This reference book, developed to present options for the prevention and treatment of child sexual abuse, contains descriptions of creative approaches used to address the problem of child sexual abuse. Some of the programs described offer active and entertaining interventions, such as puppet shows, coloring books, stories, teddy bears, and…

  3. Human Factors Experimental Design and Analysis Reference

    Science.gov (United States)

    2007-07-01

    8.75 83.36 8 =where, tObserved YPD = 53.75 YSD = 62.00 3.6.5. Within-Subjects t-Test (Cont’d) (Click in this red rectangle to see SAS calculations...expands computer experience into 3 levels, High, Medium , and Low, as compared to the original example that used only 2 levels of computer experience...High and Low. In this example, each of the 80 subjects who used the experimental text editor rated their computer experience as high, medium , or

  4. Description of the magnox type of gas cooled reactor (MAGNOX)

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, S.E.; Nonboel, E

    1999-05-01

    The present report comprises a technical description of the MAGNOX type of reactor as it has been build in Great Britain. The Magnox reactor is gas cooled (CO{sub 2}) with graphite moderators. The fuels is natural uranium in metallic form, canned with a magnesium alloy called 'Magnox'. The Calder Hall Magnox plant on the Lothian coastline of Scotland, 60 km east of Edinburgh, has been chosen as the reference plant and is described in some detail. Data on the other stations are given in tables with a summary of design data. Special design features are also shortly described. Where specific data for Calder Hall Magnox has not been available, corresponding data from other Magnox plants has been used. The information presented is based on the open literature. The report is written as a part of the NKS/RAK-2 sub-project 3: 'Reactors in Nordic Surroundings', which comprises a description of nuclear power plants neighbouring the Nordic countries. (au)

  5. Reliability of semiology description.

    Science.gov (United States)

    Heo, Jae-Hyeok; Kim, Dong Wook; Lee, Seo-Young; Cho, Jinwhan; Lee, Sang-Kun; Nam, Hyunwoo

    2008-01-01

    Seizure semiology is important for classifying patients' epilepsy. Physicians usually get most of the seizure information from observers though there have been few reports on the reliability of the observers' description. This study aims at determining the reliability of observers' description of the semiology. We included 92 patients who had their habitual seizures recorded during video-EEG monitoring. We compared the semiology described by the observers with that recorded on the videotape, and reviewed which characteristics of the observers affected the reliability of their reported data. The classification of seizures and the individual components of the semiology based only on the observer-description was somewhat discordant compared with the findings from the videotape (correct classification, 85%). The descriptions of some ictal behaviors such as oroalimentary automatism, tonic/dystonic limb posturing, and head versions were relatively accurate, but those of motionless staring and hand automatism were less accurate. The specified directions by the observers were relatively correct. The accuracy of the description was related to the educational level of the observers. Much of the information described by well-educated observers is reliable. However, every physician should keep in mind the limitations of this information and use this information cautiously.

  6. The NASA MSFC Earth Global Reference Atmospheric Model-2007 Version

    Science.gov (United States)

    Leslie, F.W.; Justus, C.G.

    2008-01-01

    Reference or standard atmospheric models have long been used for design and mission planning of various aerospace systems. The NASA/Marshall Space Flight Center (MSFC) Global Reference Atmospheric Model (GRAM) was developed in response to the need for a design reference atmosphere that provides complete global geographical variability, and complete altitude coverage (surface to orbital altitudes) as well as complete seasonal and monthly variability of the thermodynamic variables and wind components. A unique feature of GRAM is that, addition to providing the geographical, height, and monthly variation of the mean atmospheric state, it includes the ability to simulate spatial and temporal perturbations in these atmospheric parameters (e.g. fluctuations due to turbulence and other atmospheric perturbation phenomena). A summary comparing GRAM features to characteristics and features of other reference or standard atmospheric models, can be found Guide to Reference and Standard Atmosphere Models. The original GRAM has undergone a series of improvements over the years with recent additions and changes. The software program is called Earth-GRAM2007 to distinguish it from similar programs for other bodies (e.g. Mars, Venus, Neptune, and Titan). However, in order to make this Technical Memorandum (TM) more readable, the software will be referred to simply as GRAM07 or GRAM unless additional clarity is needed. Section 1 provides an overview of the basic features of GRAM07 including the newly added features. Section 2 provides a more detailed description of GRAM07 and how the model output generated. Section 3 presents sample results. Appendices A and B describe the Global Upper Air Climatic Atlas (GUACA) data and the Global Gridded Air Statistics (GGUAS) database. Appendix C provides instructions for compiling and running GRAM07. Appendix D gives a description of the required NAMELIST format input. Appendix E gives sample output. Appendix F provides a list of available

  7. Magnetohydrodynamics (MHD) Engineering Test Facility (ETF) 200 MWe power plant Conceptual Design Engineering Report (CDER)

    Science.gov (United States)

    1981-01-01

    The reference conceptual design of the magnetohydrodynamic (MHD) Engineering Test Facility (ETF), a prototype 200 MWe coal-fired electric generating plant designed to demonstrate the commercial feasibility of open cycle MHD, is summarized. Main elements of the design, systems, and plant facilities are illustrated. System design descriptions are included for closed cycle cooling water, industrial gas systems, fuel oil, boiler flue gas, coal management, seed management, slag management, plant industrial waste, fire service water, oxidant supply, MHD power ventilating

  8. Career Path Descriptions

    CERN Document Server

    Charkiewicz, A

    2000-01-01

    Before the Career Path system, jobs were classified according to grades with general statutory definitions, guided by the "Job Catalogue" which defined 6 evaluation criteria with example illustrations in the form of "typical" job descriptions. Career Paths were given concise statutory definitions necessitating a method of description and evaluation adapted to their new wider-band salary concept. Evaluations were derived from the same 6 criteria but the typical descriptions became unusable. In 1999, a sub-group of the Standing Concertation Committee proposed a new guide for describing Career Paths, adapted to their wider career concept by expanding the 6 evaluation criteria into 9. For each criterion several levels were established tracing the expected evolution of job level profiles and personal competencies over their longer salary ranges. While providing more transparency to supervisors and staff, the Guide's official use would be by services responsible for vacancy notices, Career Path evaluations and rela...

  9. 2002 reference document; Document de reference 2002

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-07-01

    This 2002 reference document of the group Areva, provides information on the society. Organized in seven chapters, it presents the persons responsible for the reference document and for auditing the financial statements, information pertaining to the transaction, general information on the company and share capital, information on company operation, changes and future prospects, assets, financial position, financial performance, information on company management and executive board and supervisory board, recent developments and future prospects. (A.L.B.)

  10. Olkiluoto site description 2011

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-12-15

    This fourth version of the Olkiluoto Site Report, produced by the OMTF (Olkiluoto Modelling Task Force), updates the Olkiluoto Site Report 2008 with the data and knowledge obtained up to December 2010. A descriptive model of the site (the Site Descriptive Model, SDM), i.e. a model describing the geological and hydrogeological structure of the site, properties of the bedrock and the groundwater and its flow, and the associated interacting processes and mechanisms. The SDM is divided into six parts: surface system, geology, rock mechanics, hydrogeology, hydrogeochemistry and transport properties.

  11. CRAC2 model description

    Energy Technology Data Exchange (ETDEWEB)

    Ritchie, L.T.; Alpert, D.J.; Burke, R.P.; Johnson, J.D.; Ostmeyer, R.M.; Aldrich, D.C.; Blond, R.M.

    1984-03-01

    The CRAC2 computer code is a revised version of CRAC (Calculation of Reactor Accident Consequences) which was developed for the Reactor Safety Study. This document provides an overview of the CRAC2 code and a description of each of the models used. Significant improvements incorporated into CRAC2 include an improved weather sequence sampling technique, a new evacuation model, and new output capabilities. In addition, refinements have been made to the atmospheric transport and deposition model. Details of the modeling differences between CRAC2 and CRAC are emphasized in the model descriptions.

  12. Technology, safety, and costs of decommissioning a reference nuclear fuel reprocessing plant. [Appendices only

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, K.J.; Jenkins, C.E.; Rhoads, R.E.

    1977-09-01

    Volume 2 comprises six appendices on: facility description; residual radioactivity inventory estimates; description and contamination levels of reference site; derivation of residual contamination levels; decommissioning mode detail; and decommissioning safety assessment details.

  13. High Luminosity LHC Project Description

    CERN Document Server

    Apollinari, Giorgio; Rossi, Lucio

    2014-01-01

    The High Luminosity LHC (HL-LHC) is a novel configuration of the Large Hadron Collider, aiming at increasing the luminosity by a factor five or more above the nominal LHC design, to allow increasing the integrated luminosity, in the high luminosity experiments ATLAS and CMS, from the 300 fb-1 of the LHC original design up to 3000 fb-1 or more. This paper contains a short description of the main machine parameters and of the main equipment that need to be developed and installed. The preliminary cost evaluation and the time plan are presented, too. Finally, the international collaboration that is supporting the project, the governance and the project structure are discussed, too.

  14. Reversible gates and circuits descriptions

    Science.gov (United States)

    Gracki, Krzystof

    2017-08-01

    This paper presents basic methods of reversible circuit description. To design reversible circuit a set of gates has to be chosen. Most popular libraries are composed of three types of gates so called CNT gates (Control, NOT and Toffoli). The gate indexing method presented in this paper is based on the CNT gates set. It introduces a uniform indexing of the gates used during synthesis process of reversible circuits. The paper is organized as follows. Section 1 recalls basic concepts of reversible logic. In Section 2 and 3 a graphical representation of the reversible gates and circuits is described. Section 4 describes proposed uniform NCT gates indexing. The presented gate indexing method provides gate numbering scheme independent of lines number of the designed circuit. The solution for a circuit consisting of smaller number of lines is a subset of solution for a larger circuit.

  15. CMS Statistics Reference Booklet

    Data.gov (United States)

    U.S. Department of Health & Human Services — The annual CMS Statistics reference booklet provides a quick reference for summary information about health expenditures and the Medicare and Medicaid health...

  16. A descriptive study

    African Journals Online (AJOL)

    Complementary medicine use among Moroccan patients with cancer: A descriptive study. ... Complementary medicine must benefit, as well as conventional medicine, from scientific studies to evaluate potential benefits, toxicity and interactions with the conventional treatment to enable the oncologist better inform his patients ...

  17. Onic reference in discourse

    OpenAIRE

    Shilikhina, K.

    2011-01-01

    the paper discusses the relation between ironic nomination and the real world. Starting with a brief overview of existing theories of reference the paper explores various ways of ironic reference indefinite pronouns and noun phrases for pseudo-indefinite and definite reference respectively. Metalinguistic assessment of ironic reference is used as yet another source of information. Ironic nomination fulfills several functions: referentive, evaluative and regulative. The evaluative function bec...

  18. Qualitative Descriptive Methods in Health Science Research.

    Science.gov (United States)

    Colorafi, Karen Jiggins; Evans, Bronwynne

    2016-07-01

    The purpose of this methodology paper is to describe an approach to qualitative design known as qualitative descriptive that is well suited to junior health sciences researchers because it can be used with a variety of theoretical approaches, sampling techniques, and data collection strategies. It is often difficult for junior qualitative researchers to pull together the tools and resources they need to embark on a high-quality qualitative research study and to manage the volumes of data they collect during qualitative studies. This paper seeks to pull together much needed resources and provide an overview of methods. A step-by-step guide to planning a qualitative descriptive study and analyzing the data is provided, utilizing exemplars from the authors' research. This paper presents steps to conducting a qualitative descriptive study under the following headings: describing the qualitative descriptive approach, designing a qualitative descriptive study, steps to data analysis, and ensuring rigor of findings. The qualitative descriptive approach results in a summary in everyday, factual language that facilitates understanding of a selected phenomenon across disciplines of health science researchers. © The Author(s) 2016.

  19. FHR Generic Design Criteria

    Energy Technology Data Exchange (ETDEWEB)

    Flanagan, G.F.; Holcomb, D.E.; Cetiner, S.M.

    2012-06-15

    The purpose of this document is to provide an initial, focused reference to the safety characteristics of and a licensing approach for Fluoride-Salt-Cooled High-Temperature Reactors (FHRs). The document does not contain details of particular reactor designs nor does it attempt to identify or classify either design basis or beyond design basis accidents. Further, this document is an initial attempt by a small set of subject matter experts to document the safety and licensing characteristics of FHRs for a larger audience. The document is intended to help in setting the safety and licensing research, development, and demonstration path forward. Input from a wider audience, further technical developments, and additional study will be required to develop a consensus position on the safety and licensing characteristics of FHRs. This document begins with a brief overview of the attributes of FHRs and then a general description of their anticipated safety performance. Following this, an overview of the US nuclear power plant approval process is provided that includes both test and power reactors, as well as the role of safety standards in the approval process. The document next describes a General Design Criteria (GDC)–based approach to licensing an FHR and provides an initial draft set of FHR GDCs. The document concludes with a description of a path forward toward developing an FHR safety standard that can support both a test and power reactor licensing process.

  20. FHR Generic Design Criteria

    Energy Technology Data Exchange (ETDEWEB)

    Flanagan, George F [ORNL; Holcomb, David Eugene [ORNL; Cetiner, Sacit M [ORNL

    2012-06-01

    The purpose of this document is to provide an initial, focused reference to the safety characteristics of and a licensing approach for Fluoride-Salt-Cooled High-Temperature Reactors (FHRs). The document does not contain details of particular reactor designs nor does it attempt to identify or classify either design basis or beyond design basis accidents. Further, this document is an initial attempt by a small set of subject matter experts to document the safety and licensing characteristics of FHRs for a larger audience. The document is intended to help in setting the safety and licensing research, development, and demonstration path forward. Input from a wider audience, further technical developments, and additional study will be required to develop a consensus position on the safety and licensing characteristics of FHRs. This document begins with a brief overview of the attributes of FHRs and then a general description of their anticipated safety performance. Following this, an overview of the US nuclear power plant approval process is provided that includes both test and power reactors, as well as the role of safety standards in the approval process. The document next describes a General Design Criteria (GDC) - based approach to licensing an FHR and provides an initial draft set of FHR GDCs. The document concludes with a description of a path forward toward developing an FHR safety standard that can support both a test and power reactor licensing process.

  1. Herbal reference standards.

    Science.gov (United States)

    Schwarz, Michael; Klier, Bernhard; Sievers, Hartwig

    2009-06-01

    This review describes the current definitions and regulatory requirements that apply to reference standards that are used to analyse herbal products. It also describes and discusses the current use of reference substances and reference extracts in the European and United States pharmacopoeias.

  2. Employing a Qualitative Description Approach in Health Care Research.

    Science.gov (United States)

    Bradshaw, Carmel; Atkinson, Sandra; Doody, Owen

    2017-01-01

    A qualitative description design is particularly relevant where information is required directly from those experiencing the phenomenon under investigation and where time and resources are limited. Nurses and midwives often have clinical questions suitable to a qualitative approach but little time to develop an exhaustive comprehension of qualitative methodological approaches. Qualitative description research is sometimes considered a less sophisticated approach for epistemological reasons. Another challenge when considering qualitative description design is differentiating qualitative description from other qualitative approaches. This article provides a systematic and robust journey through the philosophical, ontological, and epistemological perspectives, which evidences the purpose of qualitative description research. Methods and rigor issues underpinning qualitative description research are also appraised to provide the researcher with a systematic approach to conduct research utilizing this approach. The key attributes and value of qualitative description research in the health care professions will be highlighted with the aim of extending its usage.

  3. Microgrid cyber security reference architecture.

    Energy Technology Data Exchange (ETDEWEB)

    Veitch, Cynthia K.; Henry, Jordan M.; Richardson, Bryan T.; Hart, Derek H.

    2013-07-01

    This document describes a microgrid cyber security reference architecture. First, we present a high-level concept of operations for a microgrid, including operational modes, necessary power actors, and the communication protocols typically employed. We then describe our motivation for designing a secure microgrid; in particular, we provide general network and industrial control system (ICS)-speci c vulnerabilities, a threat model, information assurance compliance concerns, and design criteria for a microgrid control system network. Our design approach addresses these concerns by segmenting the microgrid control system network into enclaves, grouping enclaves into functional domains, and describing actor communication using data exchange attributes. We describe cyber actors that can help mitigate potential vulnerabilities, in addition to performance bene ts and vulnerability mitigation that may be realized using this reference architecture. To illustrate our design approach, we present a notional a microgrid control system network implementation, including types of communica- tion occurring on that network, example data exchange attributes for actors in the network, an example of how the network can be segmented to create enclaves and functional domains, and how cyber actors can be used to enforce network segmentation and provide the neces- sary level of security. Finally, we describe areas of focus for the further development of the reference architecture.

  4. Descriptions of self-mutilation among Finnish adolescents: a qualitative descriptive inquiry.

    Science.gov (United States)

    Rissanen, Marja-Liisa; Kylmä, Jari; Laukkanen, Eila

    2008-01-01

    The purpose of this study was to describe self-mutilation from the perspectives of self-mutilating adolescents. A qualitative descriptive design was adopted. Self-mutilating adolescents were asked to write descriptions of their self-mutilation. Data analysis revealed three major categories: descriptions of the factors contributing to self-mutilation, descriptions of the act of self-mutilation, and descriptions of the sequels of self-mutilation. This study adds to our understanding of self-mutilation and the experiences of self-mutilating adolescents. In nursing practice and education, self-mutilation should be discussed based on existing knowledge to make nurses more familiar with it. Nurses should understand this phenomenon as a challenge for developing effective nursing practices.

  5. Polemic and Descriptive Negations

    DEFF Research Database (Denmark)

    Horslund, Camilla Søballe

    2011-01-01

    to semantics and pragmatics, negations can be used in three different ways, which gives rise to a typology of three different types of negations: 1) the descriptive negation, 2) the polemic negation, and 3) the meta-linguistic negation (Nølke 1999, 4). This typology illuminates the fact that the negation...... as such may be more or less central to the meaning of the utterance. The present paper investigates the role of morphosyntactic and prosodic prominence as well as register and social setting on the interpretation of negations. It seems plausible to expect that if the negation as such is central to the meaning...... of the utterance (as in polemic negations), the negation will be articulated prominently in order to emphasise this importance. Likewise, if the negation is not central to the meaning of the utterance, it should not be articulated prominently. Moreover, it is plausible to expect descriptive negations to be more...

  6. Sensor Characteristics Reference Guide

    Energy Technology Data Exchange (ETDEWEB)

    Cree, Johnathan V.; Dansu, A.; Fuhr, P.; Lanzisera, Steven M.; McIntyre, T.; Muehleisen, Ralph T.; Starke, M.; Banerjee, Pranab; Kuruganti, T.; Castello, C.

    2013-04-01

    The Buildings Technologies Office (BTO), within the U.S. Department of Energy (DOE), Office of Energy Efficiency and Renewable Energy (EERE), is initiating a new program in Sensor and Controls. The vision of this program is: • Buildings operating automatically and continuously at peak energy efficiency over their lifetimes and interoperating effectively with the electric power grid. • Buildings that are self-configuring, self-commissioning, self-learning, self-diagnosing, self-healing, and self-transacting to enable continuous peak performance. • Lower overall building operating costs and higher asset valuation. The overarching goal is to capture 30% energy savings by enhanced management of energy consuming assets and systems through development of cost-effective sensors and controls. One step in achieving this vision is the publication of this Sensor Characteristics Reference Guide. The purpose of the guide is to inform building owners and operators of the current status, capabilities, and limitations of sensor technologies. It is hoped that this guide will aid in the design and procurement process and result in successful implementation of building sensor and control systems. DOE will also use this guide to identify research priorities, develop future specifications for potential market adoption, and provide market clarity through unbiased information

  7. Understanding descriptive statistics.

    Science.gov (United States)

    Fisher, Murray J; Marshall, Andrea P

    2009-05-01

    There is an increasing expectation that critical care nurses use clinical research when making decisions about patient care. This article is the second in a series which addresses statistics for clinical nursing practice. In this article we provide an introduction to the use of descriptive statistics. Concepts such as levels of measurement, measures of central tendency and dispersion are described and their use in clinical practice is illustrated.

  8. WASTE PACKAGE DESIGN SENSITIVITY REPORT

    Energy Technology Data Exchange (ETDEWEB)

    P. Mecharet

    2001-03-09

    The purpose of this technical report is to present the current designs for waste packages and determine which designs will be evaluated for the Site Recommendation (SR) or Licence Application (LA), to demonstrate how the design will be shown to comply with the applicable design criteria. The evaluations to support SR or LA are based on system description document criteria. The objective is to determine those system description document criteria for which compliance is to be demonstrated for SR; and, having identified the criteria, to refer to the documents that show compliance. In addition, those system description document criteria for which compliance will be addressed for LA are identified, with a distinction made between two steps of the LA process: the LA-Construction Authorization (LA-CA) phase on one hand, and the LA-Receive and Possess (LA-R&P) phase on the other hand. The scope of this work encompasses the Waste Package Project disciplines for criticality, shielding, structural, and thermal analysis.

  9. Genetics Home Reference: hemophilia

    Science.gov (United States)

    ... Share: Email Facebook Twitter Home Health Conditions Hemophilia Hemophilia Printable PDF Open All Close All Enable Javascript to view the expand/collapse boxes. Description Hemophilia is a bleeding disorder that slows the blood ...

  10. Genetics Home Reference: sialidosis

    Science.gov (United States)

    ... Share: Email Facebook Twitter Home Health Conditions Sialidosis Sialidosis Printable PDF Open All Close All Enable Javascript to view the expand/collapse boxes. Description Sialidosis is a severe inherited disorder that affects many ...

  11. Genetics Home Reference: osteoarthritis

    Science.gov (United States)

    ... Share: Email Facebook Twitter Home Health Conditions Osteoarthritis Osteoarthritis Printable PDF Open All Close All Enable Javascript to view the expand/collapse boxes. Description Osteoarthritis is a common disease of the joints that ...

  12. Genetics Home Reference: schizophrenia

    Science.gov (United States)

    ... Share: Email Facebook Twitter Home Health Conditions Schizophrenia Schizophrenia Printable PDF Open All Close All Enable Javascript to view the expand/collapse boxes. Description Schizophrenia is a brain disorder classified as a psychosis, ...

  13. Genetics Home Reference: aniridia

    Science.gov (United States)

    ... Share: Email Facebook Twitter Home Health Conditions aniridia aniridia Printable PDF Open All Close All Enable Javascript to view the expand/collapse boxes. Description Aniridia is an eye disorder characterized by a complete ...

  14. Genetics Home Reference: vitiligo

    Science.gov (United States)

    ... Share: Email Facebook Twitter Home Health Conditions Vitiligo Vitiligo Printable PDF Open All Close All Enable Javascript to view the expand/collapse boxes. Description Vitiligo is a condition that causes patchy loss of ...

  15. Genetics Home Reference: porphyria

    Science.gov (United States)

    ... Share: Email Facebook Twitter Home Health Conditions Porphyria Porphyria Printable PDF Open All Close All Enable Javascript to view the expand/collapse boxes. Description Porphyria is a group of disorders caused by abnormalities ...

  16. Genetics Home Reference: achondroplasia

    Science.gov (United States)

    ... Share: Email Facebook Twitter Home Health Conditions Achondroplasia Achondroplasia Printable PDF Open All Close All Enable Javascript to view the expand/collapse boxes. Description Achondroplasia is a form of short-limbed dwarfism. The ...

  17. Genetics Home Reference: SADDAN

    Science.gov (United States)

    ... view the expand/collapse boxes. Description SADDAN (severe achondroplasia with developmental delay and acanthosis nigricans) is a ... Genetic Testing (1 link) Genetic Testing Registry: Severe achondroplasia with developmental delay and acanthosis nigricans Other Diagnosis ...

  18. Genetics Home Reference: preeclampsia

    Science.gov (United States)

    ... Share: Email Facebook Twitter Home Health Conditions Preeclampsia Preeclampsia Printable PDF Open All Close All Enable Javascript to view the expand/collapse boxes. Description Preeclampsia is a complication of pregnancy in which affected ...

  19. Lawrence Livermore National Laboratory Working Reference Material Production Pla

    Energy Technology Data Exchange (ETDEWEB)

    Wong, Amy; Thronas, Denise; Marshall, Robert

    1998-11-04

    This Lawrence Livermore National Laboratory (LLNL) Working Reference Material Production Plan was written for LLNL by the Los Alamos National Laboratory to address key elements of producing seven Pu-diatomaceous earth NDA Working Reference Materials (WRMS). These WRMS contain low burnup Pu ranging in mass from 0.1 grams to 68 grams. The composite Pu mass of the seven WRMS was designed to approximate the maximum TRU allowable loading of 200 grams Pu. This document serves two purposes: first, it defines all the operations required to meet the LLNL Statement of Work quality objectives, and second, it provides a record of the production and certification of the WRMS. Guidance provided in ASTM Standard Guide C1128-89 was used to ensure that this Plan addressed all the required elements for producing and certifying Working Reference Materials. The Production Plan was written to provide a general description of the processes, steps, files, quality control, and certification measures that were taken to produce the WRMS. The Plan identifies the files where detailed procedures, data, quality control, and certification documentation and forms are retained. The Production Plan is organized into three parts: a) an initial section describing the preparation and characterization of the Pu02 and diatomaceous earth materials, b) middle sections describing the loading, encapsulation, and measurement on the encapsulated WRMS, and c) final sections describing the calculations of the Pu, Am, and alpha activity for the WRMS and the uncertainties associated with these quantities.

  20. Reference models for advanced e-services

    NARCIS (Netherlands)

    Mendes, M.J.; Vissers, C.A.; Suomi, R.; Lankhorst, M.M.; Passos, C.; Slagter, R.J.

    2004-01-01

    Reference models (RMs) capitalize on the experience that key functions and relationships determine a system’s main design structure which has to be established before other design details can be settled. As such RMs can play an important role in designing complex (distributed) systems, in allocating

  1. Descriptive data of JENDL-3.2

    Energy Technology Data Exchange (ETDEWEB)

    Shibata, Keiichi; Narita, Tsutomu [eds.] [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1998-02-01

    The second revision of JENDL-3 (JENDL-3.2) was released in 1994. The library contains evaluated neutron nuclear data for 340 nuclides which are needed for the design of fission and fusion reactors and for shielding calculation. This report presents a brief description of the evaluation method which is given in the File-1 part of JENDL-3.2. (author)

  2. Reference Dependent Altruism

    OpenAIRE

    Breitmoser, Yves; Tan, Jonathan H.W.

    2014-01-01

    In view of behavioral patterns left unorganized by current social preference theories, we propose a theory of reference dependent altruism (RDA). With RDA, one's degree of altruism increases at reference points. It induces equity and efficiency effects that are conditional on whether or not payoffs meet reference points. We verify the theory first by experimentally analyzing majority bargaining, where observed behavior contradicts existing theories but confirms RDA. Using parameter estimates ...

  3. Android quick APIs reference

    CERN Document Server

    Cinar, Onur

    2015-01-01

    The Android Quick APIs Reference is a condensed code and APIs reference for the new Google Android 5.0 SDK. It presents the essential Android APIs in a well-organized format that can be used as a handy reference. You won't find any technical jargon, bloated samples, drawn out history lessons, or witty stories in this book. What you will find is a software development kit and APIs reference that is concise, to the point and highly accessible. The book is packed with useful information and is a must-have for any mobile or Android app developer or programmer. In the Android Quick APIs Refe

  4. Workplace Ergonomics Reference Guide

    Science.gov (United States)

    Workplace Ergonomics Reference Guide 2 nd Edition A Publication of the Computer/Electronic Accommodations Program Real Solutions for Real ... Table of Contents.................................................................................................................................. ... Checklist ........................................................................................................................... 3 Ergonomic ...

  5. Reference - PLACE | LSDB Archive [Life Science Database Archive metadata

    Lifescience Database Archive (English)

    Full Text Available switchLanguage; BLAST Search Image Search Home About Archive Update History Data ...ailable. Data file File name: place_reference.zip File URL: ftp://ftp.biosciencedbc.jp/archive/place/LATEST/...ber About This Database Database Description Download License Update History of This Database Site Policy | Contact Us Reference - PLACE | LSDB Archive ...

  6. FLOWTRAN-TF code description

    Energy Technology Data Exchange (ETDEWEB)

    Flach, G.P. (ed.)

    1990-12-01

    FLOWTRAN-TF is a two-component (air-water), two-phase thermal-hydraulics code designed for performing accident analyses of SRS reactor fuel assemblies during the Emergency Cooling System (ECS) phase of a Double Ended Guillotine Break (DEGB) Loss of Coolant Accident (LOCA). This report provides a brief description of the physical models in the version of FLOWTRAN-TF used to compute the Recommended K-Reactor Restart ECS Power Limit. This document is viewed as an interim report and should ultimately be superseded by a comprehensive user/programmer manual. In general, only high level discussions of governing equations and constitutive laws are presented. Numerical implementation of these models, code architecture and user information are not generally covered. A companion document describing code benchmarking is available.

  7. FLOWTRAN-TF code description

    Energy Technology Data Exchange (ETDEWEB)

    Flach, G.P. (ed.)

    1991-09-01

    FLOWTRAN-TF is a two-component (air-water), two-phase thermal-hydraulics code designed for performing accident analyses of SRS reactor fuel assemblies during the Emergency Cooling System (ECS) phase of a Double Ended Guillotine Break (DEGB) Loss of Coolant Accident (LOCA). This report provides a brief description of the physical models in the version of FLOWTRAN-TF used to compute the Recommended K-Reactor Restart ECS Power Limit. This document is viewed as an interim report and should ultimately be superseded by a comprehensive user/programmer manual. In general, only high level discussions of governing equations and constitutive laws are presented. Numerical implementation of these models, code architecture and user information are not generally covered. A companion document describing code benchmarking is available.

  8. Designing Organizations

    DEFF Research Database (Denmark)

    Book Description The design of organizations has been an ongoing concern of management theory and practice over the past several decades. Over this time, there has been little change in the fundamental theory, principles and concepts of Organization Design (OD). Recently organizational life has...

  9. Climate Reference Network Daily01 Product

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The U.S. Climate Reference Network is designed specifically to monitor national climate change with best scientific practice and adherence to the accepted principles...

  10. Climate Reference Network Hourly02 Product

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The U.S. Climate Reference Network is designed specifically to monitor national climate change with best scientific practice and adherence to the accepted principles...

  11. Description logic rules

    CERN Document Server

    Krötzsch, M

    2010-01-01

    Ontological modelling today is applied in many areas of science and technology,including the Semantic Web. The W3C standard OWL defines one of the most important ontology languages based on the semantics of description logics. An alternative is to use rule languages in knowledge modelling, as proposed in the W3C's RIF standard. So far, it has often been unclear how to combine both technologies without sacrificing essential computational properties. This book explains this problem and presents new solutions that have recently been proposed. Extensive introductory chapters provide the necessary

  12. The Reference Interview

    Science.gov (United States)

    King, Geraldine B.

    1972-01-01

    Good reference librarians need to be good interviewers. Unfortunately most librarians have not learned to use the technique of open questions to obtain information about the user and what he is looking for. Examples of open and closed questions with typical responses are given. (4 references) (DH)

  13. California's Reference Crisis.

    Science.gov (United States)

    Childers, Thomas A.

    1994-01-01

    Social and economic issues affecting the vitality of public libraries in California are discussed. A 1993 study by the California State Library identified diminishing reference skills and reference collections, reduced funding which impacted staffing, increased demand, technology change, and language/culture issues as contributing factors to…

  14. The Reference Return Ratio

    DEFF Research Database (Denmark)

    Nicolaisen, Jeppe; Faber Frandsen, Tove

    2008-01-01

    The paper introduces a new journal impact measure called The Reference Return Ratio (3R). Unlike the traditional Journal Impact Factor (JIF), which is based on calculations of publications and citations, the new measure is based on calculations of bibliographic investments (references) and returns...

  15. A revision of the family Cerococcidae Balachowsky (Hemiptera: Sternorrhyncha, Coccomorpha) with particular reference to species from the Afrotropical, western Palaearctic and western Oriental Regions, with the revival of Antecerococcus Green and description of a new genus and fifteen new species, and with ten new synonomies.

    Science.gov (United States)

    Hodgson, Chris J; Williams, Douglas J

    2016-03-14

    , C. cistarum Balachowsky, C. cliffortiae Joubert, C. coffeae Vayssière, C. cycliger Goux, C. dumonti Vayssière, C. hibisci Green, C. intermedius Balachowsky, C. laniger Goux, C. pocilliferus Neves, C. royenae Brain and C. ruber Balachowsky, and for Cercococcus eremobius Scott and Solenophora coloradensis Cockerell. In addition, it was found that the lectotype of Eriococcus paradoxus Maskell (now Antecerococcus paradoxus) had been designated based on a specimen of Eriococcus paradoxus indica Maskell (now Antecerococcus indicus). This designation has been revoked and new lectotypes for Eriococcus paradoxus and Eriococcus paradoxus indica have been designated. Following the taxonomic section, the geographic distribution of each genus is briefly discussed. Asterococcus (with the removal of A. ovoides) is now restricted to the Oriental Region; Cerochiton is restricted to the southern part of the Oriental Region; Cerococcus appears to be restricted to Central and North America, while Antecerococcus has a world-wide distribution but is most abundant in the western Palaearctic, western Oriental and Afrotropical Regions. The single species now in Solenophora is only known from New Zealand. Two species, "Cerococcus" indonesiensis Lambdin & Kosztarab and "Cerococcus" michaeli Lambdin do not appear to belong to Cerococcus, but are being left there pending further studies and are referred to here as "unplaced species".

  16. Physics within a quantum reference frame

    OpenAIRE

    Angelo, Renato M.; Brunner, Nicolas; Popescu, Sandu; Short, Anthony J.; Skrzypczyk, Paul

    2010-01-01

    We investigate the physics of quantum reference frames. Specifically, we study several simple scenarios involving a small number of quantum particles, whereby we promote one of these particles to the role of a quantum observer and ask what is the description of the rest of the system, as seen by this observer? We highlight the interesting aspects of such questions by presenting a number of apparent paradoxes. By unravelling these paradoxes we get a better understanding of the physics of quant...

  17. Description of surface systems. Preliminary site description. Forsmark area Version 1.2

    Energy Technology Data Exchange (ETDEWEB)

    Lindborg, Tobias (ed.)

    2005-06-01

    the biosphere. Methodologies for developing descriptive- and ecosystem models are only described briefly in this report, but for thorough methodology descriptions see references. The work has been conducted by the project group SurfaceNet together with other discipline-specific collaborators, engaged by members of the project group. The members of the project group represent the disciplines ecology, hydrology, Quaternary geology, soil science, limnology, oceanography, hydrogeology, hydrogeochemistry, environmental science, physical geography and human geography. In addition, some group members have specific qualifications of importance, e.g. experts in GIS modelling and in statistical data analysis.

  18. Natural Channel Design Review Checklist

    Science.gov (United States)

    This document presents a brief description of the checklist items by the following sections: Watershed and Geomorphic Assessment, Preliminary Design, Final Design, and Maintenance and Monitoring Plans.

  19. 77 FR 14012 - Eligible Telecommunications Carrier Designation for Participation in Mobility Fund Phase I

    Science.gov (United States)

    2012-03-08

    ... auction. Auction applications in spectrum license auctions typically must be filed two to three months... should refer to relevant Commission rules and orders to ensure that they meet all the requirements for ETC designation. To the extent that any part of the descriptive overview in the Auction 901 ETC Public...

  20. Microsoft Windows 7 Administration Instant Reference

    CERN Document Server

    Panek, William

    2010-01-01

    An on-the-spot reference for Windows 7 administrators. Hundreds of thousands of IT administrators, network administrators, and IT support technicians work daily with Windows 7. This well-organized, portable reference covers every facet of Windows 7, providing no-nonsense instruction that is readily accessible when you need it. Designed for busy administrators, it features thumb tabs and chapter outlines to make answers easy to find.: Windows 7 administrative and support personnel need quick answers to situations they confront each day; this Instant Reference is designed to provide information,

  1. Legal protection of design by Community designs

    OpenAIRE

    Bielanová, Markéta

    2016-01-01

    The subject of this thesis is the introduction to legal protection of industrial design at EU level through Community design, and comparison of Community design with other types of legal protection available. The thesis is divided into two parts. The first part explains the terms 'design' and 'Community design', while the second part compares Community design with other industrial design legal protection systems. The second part also provides a description of how both Community design and oth...

  2. Adaptive Control with Reference Model Modification

    Science.gov (United States)

    Stepanyan, Vahram; Krishnakumar, Kalmanje

    2012-01-01

    This paper presents a modification of the conventional model reference adaptive control (MRAC) architecture in order to improve transient performance of the input and output signals of uncertain systems. A simple modification of the reference model is proposed by feeding back the tracking error signal. It is shown that the proposed approach guarantees tracking of the given reference command and the reference control signal (one that would be designed if the system were known) not only asymptotically but also in transient. Moreover, it prevents generation of high frequency oscillations, which are unavoidable in conventional MRAC systems for large adaptation rates. The provided design guideline makes it possible to track a reference commands of any magnitude from any initial position without re-tuning. The benefits of the method are demonstrated with a simulation example

  3. Memory design

    DEFF Research Database (Denmark)

    Tanderup, Sisse

    Mind and Matter - Nordik 2009 Conference for Art Historians Design Matters Contributed Memory design BACKGROUND My research concerns the use of memory categories in the designs by the companies Alessi and Georg Jensen. When Alessi's designers create their products, they are usually inspired...... by cultural forms, often specifically by the concept of memory in philosophy, sociology and psychology, while Danish design traditionally has been focusing on form and function with frequent references to the forms of nature. Alessi's motivation for investigating the concept of memory is that it adds...... a cultural dimension to the design objects, enabling the objects to make an identity-forming impact. Whether or not the concept of memory plays a significant role in Danish design has not yet been elucidated fully. TERMINOLOGY The concept of "memory design" refers to the idea that design carries...

  4. STL pocket reference

    CERN Document Server

    Lischner, Ray

    2003-01-01

    The STL Pocket Reference describes the functions, classes, and templates in that part of the C++ standard library often referred to as the Standard Template Library (STL). The STL encompasses containers, iterators, algorithms, and function objects, which collectively represent one of the most important and widely used subsets of standard library functionality. The C++ standard library, even the subset known as the STL, is vast. It's next to impossible to work with the STL without some sort of reference at your side to remind you of template parameters, function invocations, return types--ind

  5. R quick syntax reference

    CERN Document Server

    Tollefson, Margot

    2014-01-01

    The R Quick Syntax Reference is a handy reference book detailing the intricacies of the R language. Not only is R a free, open-source tool, R is powerful, flexible, and has state of the art statistical techniques available. With the many details which must be correct when using any language, however, the R Quick Syntax Reference makes using R easier.Starting with the basic structure of R, the book takes you on a journey through the terminology used in R and the syntax required to make R work. You will find looking up the correct form for an expression quick and easy. With a copy of the R Quick

  6. LINQ Pocket Reference

    CERN Document Server

    Albahari, Joseph

    2008-01-01

    Ready to take advantage of LINQ with C# 3.0? This guide has the detail you need to grasp Microsoft's new querying technology, and concise explanations to help you learn it quickly. And once you begin to apply LINQ, the book serves as an on-the-job reference when you need immediate reminders. All the examples in the LINQ Pocket Reference are preloaded into LINQPad, the highly praised utility that lets you work with LINQ interactively. Created by the authors and free to download, LINQPad will not only help you learn LINQ, it will have you thinking in LINQ. This reference explains: LINQ's ke

  7. Regular Expression Pocket Reference

    CERN Document Server

    Stubblebine, Tony

    2007-01-01

    This handy little book offers programmers a complete overview of the syntax and semantics of regular expressions that are at the heart of every text-processing application. Ideal as a quick reference, Regular Expression Pocket Reference covers the regular expression APIs for Perl 5.8, Ruby (including some upcoming 1.9 features), Java, PHP, .NET and C#, Python, vi, JavaScript, and the PCRE regular expression libraries. This concise and easy-to-use reference puts a very powerful tool for manipulating text and data right at your fingertips. Composed of a mixture of symbols and text, regular exp

  8. Handbook of reference electrodes

    CERN Document Server

    Inzelt, György; Scholz, Fritz

    2013-01-01

    Reference Electrodes are a crucial part of any electrochemical system, yet an up-to-date and comprehensive handbook is long overdue. Here, an experienced team of electrochemists provides an in-depth source of information and data for the proper choice and construction of reference electrodes. This includes all kinds of applications such as aqueous and non-aqueous solutions, ionic liquids, glass melts, solid electrolyte systems, and membrane electrodes. Advanced technologies such as miniaturized, conducting-polymer-based, screen-printed or disposable reference electrodes are also covered. Essen

  9. Biomedical Engineering Desk Reference

    CERN Document Server

    Ratner, Buddy D; Schoen, Frederick J; Lemons, Jack E; Dyro, Joseph; Martinsen, Orjan G; Kyle, Richard; Preim, Bernhard; Bartz, Dirk; Grimnes, Sverre; Vallero, Daniel; Semmlow, John; Murray, W Bosseau; Perez, Reinaldo; Bankman, Isaac; Dunn, Stanley; Ikada, Yoshito; Moghe, Prabhas V; Constantinides, Alkis

    2009-01-01

    A one-stop Desk Reference, for Biomedical Engineers involved in the ever expanding and very fast moving area; this is a book that will not gather dust on the shelf. It brings together the essential professional reference content from leading international contributors in the biomedical engineering field. Material covers a broad range of topics including: Biomechanics and Biomaterials; Tissue Engineering; and Biosignal Processing* A hard-working desk reference providing all the essential material needed by biomedical and clinical engineers on a day-to-day basis * Fundamentals, key techniques,

  10. Metaphorical descriptions of wrongdoers

    Directory of Open Access Journals (Sweden)

    Dryll Ewa Marta

    2017-10-01

    Full Text Available What is a metaphoric picture of an evil person made of? In a study devoted to the development of the ability to use metaphorical descriptions of humans, the semantic fields of four target metaphors - Human-Swamp, Human-Snake, Human-Knife, and Human-Nettle - were established and compared. Subjects (365 young adults were asked to decipher the metaphors’ meanings. The results were obtained mainly by qualitative analysis, with frequency analysis of clusters containing synonymous meanings. The results indicate that when creating imaginary characteristics of evil people, young adults seem to be more concerned about the possibility of suffering verbal harassment (most commonly: vulgarity, mockery, gossip, jeering than the threat of actual physical assault. The results may prove useful for developmental comparisons.

  11. From description to prescription

    DEFF Research Database (Denmark)

    McQuaid, Sara Dybris

    with official policy documents makes for an interesting intertextual site of conflict interpretation and the dis/connections between these discourses in approaching diversity. Through an analysis of three seminal works which categorises theoretical interpretations of the conflict (Lijphart: The Northern Ireland......From Description to Prescription: Politics of Recognition, Consociational Theory and the Conflict in Northern Ireland. Within academic discourses on Northern Ireland the politics of recognition and particularly the theory of consociational democracy has made a profound impact. First introduced...... Problem: cases, theories and solutions (1975); Whyte: Interpreting Northern Ireland (1990); McGarry and O’Leary Explaining Northern Ireland (1995)), the paper will trace the historical development of intellectual understandings of the conflict as well as the propelling of consociational theory to its...

  12. Task Description Language

    Science.gov (United States)

    Simmons, Reid; Apfelbaum, David

    2005-01-01

    Task Description Language (TDL) is an extension of the C++ programming language that enables programmers to quickly and easily write complex, concurrent computer programs for controlling real-time autonomous systems, including robots and spacecraft. TDL is based on earlier work (circa 1984 through 1989) on the Task Control Architecture (TCA). TDL provides syntactic support for hierarchical task-level control functions, including task decomposition, synchronization, execution monitoring, and exception handling. A Java-language-based compiler transforms TDL programs into pure C++ code that includes calls to a platform-independent task-control-management (TCM) library. TDL has been used to control and coordinate multiple heterogeneous robots in projects sponsored by NASA and the Defense Advanced Research Projects Agency (DARPA). It has also been used in Brazil to control an autonomous airship and in Canada to control a robotic manipulator.

  13. Tracking Down Abstract Linguistic Meaning: Neural Correlates of Spatial Frame of Reference Ambiguities in Language

    NARCIS (Netherlands)

    Janzen, G.; Haun, D.B.M.; Levinson, S.C.

    2012-01-01

    This functional magnetic resonance imaging (fMRI) study investigates a crucial parameter in spatial description, namely variants in the frame of reference chosen. Two frames of reference are available in European languages for the description of small-scale assemblages, namely the intrinsic (or

  14. Technology, safety, and costs of decommissioning a reference pressurized water reactor power station. Appendices

    Energy Technology Data Exchange (ETDEWEB)

    Smith, R.I.; Konzek, G.J.; Kennedy, W.E. Jr.

    1978-05-01

    Detailed appendices are presented under the following headings: reference PWR facility description, reference PWR site description, estimates of residual radioactivity, alternative methods for financing decommissioning, radiation dose methodology, generic decommissioning activities, intermediate dismantlement activities, safe storage and deferred dismantlement activities, compilation of unit cost factors, and safety assessment details.

  15. Advanced Transport Operating System (ATOPS) control display unit software description

    Science.gov (United States)

    Slominski, Christopher J.; Parks, Mark A.; Debure, Kelly R.; Heaphy, William J.

    1992-01-01

    The software created for the Control Display Units (CDUs), used for the Advanced Transport Operating Systems (ATOPS) project, on the Transport Systems Research Vehicle (TSRV) is described. Module descriptions are presented in a standardized format which contains module purpose, calling sequence, a detailed description, and global references. The global reference section includes subroutines, functions, and common variables referenced by a particular module. The CDUs, one for the pilot and one for the copilot, are used for flight management purposes. Operations performed with the CDU affects the aircraft's guidance, navigation, and display software.

  16. Spectral transmittance reference standards

    Energy Technology Data Exchange (ETDEWEB)

    Kruglyakova, M.A.; Belyaeva, O.N.; Nikitin, M.V.

    1995-06-01

    This paper presents spectral transmittance reference standards for UV and IR spectrophotometers, developed, studied, and certified by a precision spectrophotometry laboratory (the RSP Complex). 8 refs., 3 figs., 3 tabs.

  17. Toxicity Reference Database

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Toxicity Reference Database (ToxRefDB) contains approximately 30 years and $2 billion worth of animal studies. ToxRefDB allows scientists and the interested...

  18. Genetics Home Reference: aceruloplasminemia

    Science.gov (United States)

    ... an inherited neurodegenerative disease with impairment of iron homeostasis. Ann N Y Acad Sci. 2004 Mar;1012:299-305. Review. Citation on PubMed More from Genetics Home Reference Bulletins Crick, Watson, and Wilkins Awarded ...

  19. Dissolution processes. [224 references

    Energy Technology Data Exchange (ETDEWEB)

    Silver, G.L.

    1976-10-22

    This review contains more than 100 observations and 224 references on the dissolution phenomenon. The dissolution processes are grouped into three categories: methods of aqueous attack, fusion methods, and miscellaneous observations on phenomena related to dissolution problems. (DLC)

  20. Introduction to Reference Links

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Unlike most traditional metadata systems, the power of ServCat comes in relating a Reference to others. This module discusses the different types of links (aka...

  1. Reflectance Reference Targets (OTTER)

    Data.gov (United States)

    National Aeronautics and Space Administration — ABSTRACT: Spectral reflectance measurements of flat field targets as reference points representative of pseudo-invariant targets as measured by Spectron SE590...

  2. Reflectance Reference Targets (OTTER)

    Data.gov (United States)

    National Aeronautics and Space Administration — Spectral reflectance measurements of flat field targets as reference points representative of pseudo-invariant targets as measured by Spectron SE590 spectrophotometer

  3. Collaborative networks: Reference modeling

    NARCIS (Netherlands)

    Camarinha-Matos, L.M.; Afsarmanesh, H.

    2008-01-01

    Collaborative Networks: Reference Modeling works to establish a theoretical foundation for Collaborative Networks. Particular emphasis is put on modeling multiple facets of collaborative networks and establishing a comprehensive modeling framework that captures and structures diverse perspectives of

  4. Reference Climatological Stations

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Reference Climatological Stations (RCS) network represents the first effort by NOAA to create and maintain a nationwide network of stations located only in areas...

  5. QUILD: QUantum-regions interconnected by local descriptions

    NARCIS (Netherlands)

    Swart, M.; Bickelhaupt, F.M.

    2008-01-01

    A new program for multilevel (QM/QM and/or QM/MM) approaches is presented that is able to combine different computational descriptions for different regions in a transparent and flexible manner. This program, designated QUILD (for QUantum-regions Interconnected by Local Descriptions), uses adapted

  6. Employing a Qualitative Description Approach in Health Care Research

    OpenAIRE

    Bradshaw, Carmel; Atkinson, Sandra; Doody, Owen

    2017-01-01

    A qualitative description design is particularly relevant where information is required directly from those experiencing the phenomenon under investigation and where time and resources are limited. Nurses and midwives often have clinical questions suitable to a qualitative approach but little time to develop an exhaustive comprehension of qualitative methodological approaches. Qualitative description research is sometimes considered a less sophisticated approach for epistemological reasons. A...

  7. X Python reference manual

    OpenAIRE

    Mullender, Sjoerd

    1995-01-01

    textabstractThis document describes the built-in types, exceptions, and functions of the X windows extension to Python. It assumes basic knowledge about the Python language and access to the X windows documentation. For an informal introduction to the language, see the Python Tutorial. The Python Reference Manual gives a more formal definition of the language. The Python Library Reference describes the built-in and standard modules of Python. This document can be seen as en extension to that ...

  8. Frequency reference in VSAT

    Science.gov (United States)

    Cheah, Jonathon Y. C.

    1994-02-01

    A low cost technique of frequency reference distribution within a VSAT network is discussed. This technique allows the use of a modestly frequency stable oscillator as the master frequency reference in the hub of a star-connected VSAT network. The need for extremely frequency stable OCXOs in VSATs is completely avoided. This technique was successfully incorporated in the early commercial VSAT networks. It contributes partially to the low cost nature of some of the VSAT networks available today.

  9. Electronics engineer's reference book

    CERN Document Server

    Turner, L W

    1976-01-01

    Electronics Engineer's Reference Book, 4th Edition is a reference book for electronic engineers that reviews the knowledge and techniques in electronics engineering and covers topics ranging from basics to materials and components, devices, circuits, measurements, and applications. This edition is comprised of 27 chapters; the first of which presents general information on electronics engineering, including terminology, mathematical equations, mathematical signs and symbols, and Greek alphabet and symbols. Attention then turns to the history of electronics; electromagnetic and nuclear radiatio

  10. Reference Man anatomical model

    Energy Technology Data Exchange (ETDEWEB)

    Cristy, M.

    1994-10-01

    The 70-kg Standard Man or Reference Man has been used in physiological models since at least the 1920s to represent adult males. It came into use in radiation protection in the late 1940s and was developed extensively during the 1950s and used by the International Commission on Radiological Protection (ICRP) in its Publication 2 in 1959. The current Reference Man for Purposes of Radiation Protection is a monumental book published in 1975 by the ICRP as ICRP Publication 23. It has a wealth of information useful for radiation dosimetry, including anatomical and physiological data, gross and elemental composition of the body and organs and tissues of the body. The anatomical data includes specified reference values for an adult male and an adult female. Other reference values are primarily for the adult male. The anatomical data include much data on fetuses and children, although reference values are not established. There is an ICRP task group currently working on revising selected parts of the Reference Man document.

  11. BLOCKAGE 2.5 reference manual

    Energy Technology Data Exchange (ETDEWEB)

    Shaffer, C.J.; Brideau, J.; Rao, D.V. [Science and Engineering Associates, Inc., Albuquerque, NM (United States); Bernahl, W. [Software Edge, Inc., Riverwoods, IL (United States)

    1996-12-01

    The BLOCKAGE 2.5 code was developed by the US Nuclear Regulatory Commission (NRC) as a tool to evaluate license compliance regarding the design of suction strainers for emergency core cooling system (ECCS) pumps in boiling water reactors (BWR) as required by NRC Bulletin 96-03, ``Potential Plugging of Emergency Core Cooling Suction Strainers by Debris in Boiling Water Reactors``. Science and Engineering Associates, Inc. (SEA) and Software Edge, Inc. (SE) developed this PC-based code. The instructions to effectively use this code to evaluate the potential of debris to sufficiently block a pump suction strainer such that a pump could lose NPSH margin was documented in a User`s Manual (NRC, NUREG/CR-6370). The Reference Manual contains additional information that supports the use of BLOCKAGE 2.5. It contains descriptions of the analytical models contained in the code, programmer guides illustrating the structure of the code, and summaries of coding verification and model validation exercises that were performed to ensure that the analytical models were correctly coded and applicable to the evaluation of BWR pump suction strainers. The BLOCKAGE code was developed by SEA and programmed in FORTRAN as a code that can be executed from the DOS level on a PC. A graphical users interface (GUI) was then developed by SEA to make BLOCKAGE easier to use and to provide graphical output capability. The GUI was programmed in the C language. The user has the option of executing BLOCKAGE 2.5 with the GUI or from the DOS level and the Users Manual provides instruction for both methods of execution.

  12. Descriptive study of 192 adults with speech and language disturbances

    Directory of Open Access Journals (Sweden)

    Letícia Lessa Mansur

    Full Text Available CONTEXT: Aphasia is a very disabling condition caused by neurological diseases. In Brazil, we have little data on the profile of aphasics treated in rehabilitation centers. OBJECTIVE: To present a descriptive study of 192 patients, providing a reference sample of speech and language disturbances among Brazilians. DESIGN: Retrospective study. SETTING: Speech Pathology Unit linked to the Neurology Division of the Hospital das Clínicas of the Faculdade de Medicina da Universidade de São Paulo. SAMPLE: All patients (192 referred to our Speech Pathology service from 1995 to 2000. PROCEDURES: We collected data relating to demographic variables, etiology, language evaluation (functional evaluation, Boston Diagnostic Aphasia Examination, Boston Naming and Token Test, and neuroimaging studies. MAIN MEASUREMENTS: The results obtained in language tests and the clinical and neuroimaging data were organized and classified. Seventy aphasics were chosen for constructing a profile. Fourteen subjects with left single-lobe dysfunction were analyzed in detail. Seventeen aphasics were compared with 17 normal subjects, all performing the Token Test. RESULTS: One hundred subjects (52% were men and 92 (48% women. Their education varied from 0 to 16 years (average: 6.5; standard deviation: 4.53. We identified the lesion sites in 104 patients: 89% in the left hemisphere and 58% due to stroke. The incidence of aphasia was 70%; dysarthria and apraxia, 6%; functional alterations in communication, 17%; and 7% were normal. Statistically significant differences appeared when comparing the subgroup to controls in the Token Test. CONCLUSIONS: We believe that this sample contributes to a better understanding of neurological patients with speech and language disturbances and may be useful as a reference for health professionals involved in the rehabilitation of such disorders.

  13. Persistent Web References – Best Practices and New Suggestions

    DEFF Research Database (Denmark)

    Zierau, Eld; Nyvang, Caroline; Kromann, Thomas Hvid

    In this paper, we suggest adjustments to best practices for persistent web referencing; adjustments that aim at preservation and long time accessibility of web referenced resources in general, but with focus on web references in web archives. Web referencing is highly relevant and crucial...... for various research fields, since an increasing number of references point to resources that only exist on the web. However, present practices using URL and date reference cannot be regarded as persistent due to the volatile nature of the Internet, - and present practices for references to web archives only....... In order to explain needed change of practices based on the wPID, the paper includes a thorough description of the challenges in web references. This description is based on the perspectives from computer science, web collection and Digital Humanities....

  14. Perturbation theory for water with an associating reference fluid

    Science.gov (United States)

    Marshall, Bennett D.

    2017-11-01

    The theoretical description of the thermodynamics of water is challenged by the structural transition towards tetrahedral symmetry at ambient conditions. As perturbation theories typically assume a spherically symmetric reference fluid, they are incapable of accurately describing the liquid properties of water at ambient conditions. In this paper we address this problem by introducing the concept of an associated reference perturbation theory (APT). In APT we treat the reference fluid as an associating hard sphere fluid which transitions to tetrahedral symmetry in the fully hydrogen bonded limit. We calculate this transition in a theoretically self-consistent manner without appealing to molecular simulations. This associated reference provides the reference fluid for a second order Barker-Henderson perturbative treatment of the long-range attractions. We demonstrate that this approach gives a significantly improved description of water as compared to standard perturbation theories.

  15. Predictor-Based Model Reference Adaptive Control

    Science.gov (United States)

    Lavretsky, Eugene; Gadient, Ross; Gregory, Irene M.

    2009-01-01

    This paper is devoted to robust, Predictor-based Model Reference Adaptive Control (PMRAC) design. The proposed adaptive system is compared with the now-classical Model Reference Adaptive Control (MRAC) architecture. Simulation examples are presented. Numerical evidence indicates that the proposed PMRAC tracking architecture has better than MRAC transient characteristics. In this paper, we presented a state-predictor based direct adaptive tracking design methodology for multi-input dynamical systems, with partially known dynamics. Efficiency of the design was demonstrated using short period dynamics of an aircraft. Formal proof of the reported PMRAC benefits constitute future research and will be reported elsewhere.

  16. Dynamic HTML The Definitive Reference

    CERN Document Server

    Goodman, Danny

    2007-01-01

    Packed with information on the latest web specifications and browser features, this new edition is your ultimate one-stop resource for HTML, XHTML, CSS, Document Object Model (DOM), and JavaScript development. Here is the comprehensive reference for designers of Rich Internet Applications who need to operate in all modern browsers, including Internet Explorer 7, Firefox 2, Safari, and Opera. With this book, you can instantly see browser support for the latest standards-based technologies, including CSS Level 3, DOM Level 3, Web Forms 2.0, XMLHttpRequest for AJAX applications, JavaScript 1.7

  17. Reference Based Genome Compression

    CERN Document Server

    Chern, Bobbie; Manolakos, Alexandros; No, Albert; Venkat, Kartik; Weissman, Tsachy

    2012-01-01

    DNA sequencing technology has advanced to a point where storage is becoming the central bottleneck in the acquisition and mining of more data. Large amounts of data are vital for genomics research, and generic compression tools, while viable, cannot offer the same savings as approaches tuned to inherent biological properties. We propose an algorithm to compress a target genome given a known reference genome. The proposed algorithm first generates a mapping from the reference to the target genome, and then compresses this mapping with an entropy coder. As an illustration of the performance: applying our algorithm to James Watson's genome with hg18 as a reference, we are able to reduce the 2991 megabyte (MB) genome down to 6.99 MB, while Gzip compresses it to 834.8 MB.

  18. Ship design methodologies of preliminary design

    CERN Document Server

    Papanikolaou, Apostolos

    2014-01-01

    This book deals with ship design and in particular with methodologies of the preliminary design of ships. The book is complemented by a basic bibliography and five appendices with useful updated charts for the selection of the main dimensions and other basic characteristics of different types of ships (Appendix A), the determination of hull form  from the data of systematic hull form series (Appendix B), the detailed description of the relational method for the preliminary estimation of ship weights (Appendix C), a brief review of the historical evolution of shipbuilding science and technology from the prehistoric era to date (Appendix D) and finally a historical review of regulatory developments of ship's damage stability to date (Appendix E).  The book can be used as textbook for ship design courses or as additional reading for university or college students of naval architecture courses and related disciplines; it may also serve as a reference book for naval architects, practicing engineers of rel...

  19. Who is Referred for Sedation for Dentistry and Why?

    Science.gov (United States)

    Boyle, Carole A; Newton, Tim; Milgrom, Peter

    2013-01-01

    Objective To assess referrals to sedation examining dental anxiety and background of patients and compare these characteristics to those referred to a restorative dentistry clinic. Design Descriptive, cross sectional survey and chart review. Subjects and Methods Subjects were 100 consecutive new patients in Sedation and Special Care and 50 new patients in Restorative Dentistry at Guy’s and St Thomas NHS Foundation Trust. A questionnaire included demographics, self-reported oral health and dental attendance, and dental fear. Information from the patient’s record was taken: ASA Classification, previous sedation or general anaesthesia, and alcohol and tobacco use, and medications. Results The best predictors of referral were dental anxiety level and an irregular attendance. The most important fears were seeing, hearing and feeling the vibrations of the dental drill, and the perception of an accelerated heart rate. Other factors, such as general, mental and dental health, and alcohol use were related to referral but less important. Conclusions Referral is consistent with the goal of the Sedation Clinic to see anxious patients. Referring general practitioners are able to identify these patients. PMID:19329945

  20. Perl Pocket Reference

    CERN Document Server

    Vromans, Johan

    2011-01-01

    If you have a Perl programming question, you'll find the answer quickly in this handy, easy-to-use quick reference. The Perl Pocket Reference condenses and organizes stacks of documentation down to the most essential facts, so you can find what you need in a heartbeat. Updated for Perl 5.14, the 5th edition provides a summary of Perl syntax rules and a complete list of operators, built-in functions, and other features. It's the perfect companion to O'Reilly's authoritative and in-depth Perl programming books, including Learning Perl, Programming Perl, and the Perl Cookbook..

  1. Electrical engineer's reference book

    CERN Document Server

    Jones, G R

    2013-01-01

    A long established reference book: radical revision for the fifteenth edition includes complete rearrangement to take in chapters on new topics and regroup the subjects covered for easy access to information.The Electrical Engineer's Reference Book, first published in 1945, maintains its original aims: to reflect the state of the art in electrical science and technology and cater for the needs of practising engineers. Most chapters have been revised and many augmented so as to deal properly with both fundamental developments and new technology and applications that have come to the fore since

  2. JDBC Pocket Reference

    CERN Document Server

    Bales, Donald

    2003-01-01

    JDBC--the Java Database Connectivity specification--is a complex set of application programming interfaces (APIs) that developers need to understand if they want their Java applications to work with databases. JDBC is so complex that even the most experienced developers need to refresh their memories from time to time on specific methods and details. But, practically speaking, who wants to stop and thumb through a weighty tutorial volume each time a question arises? The answer is the JDBC Pocket Reference, a data-packed quick reference that is both a time-saver and a lifesaver. The JDBC P

  3. Reference class forecasting

    DEFF Research Database (Denmark)

    Flyvbjerg, Bent

    Underbudgettering og budgetoverskridelser forekommer i et flertal af større bygge- og anlægsprojekter. Problemet skyldes optimisme og/eller strategisk misinformation i budgetteringsprocessen. Reference class forecasting (RCF) er en prognosemetode, som er udviklet for at reducere eller eliminere...... projekterne er almindelige nationalt eller internationalt, er det muligt at etablere en reference-klasse af tilsvarende projekter og dermed alligevel opnå et pålideligt lokalt budget. Denne projekttype er relativt almindelig. RCF kan ikke anvendes på projekter som er reelt unikke, d.v.s. projekter for hvilke...

  4. bash Quick Reference

    CERN Document Server

    Robbins, Arnold

    2008-01-01

    In this quick reference, you'll find everything you need to know about the bash shell. Whether you print it out or read it on the screen, this PDF gives you the answers to the annoying questions that always come up when you're writing shell scripts: What characters do you need to quote? How do you get variable substitution to do exactly what you want? How do you use arrays? It's also helpful for interactive use. If you're a Unix user or programmer, or if you're using bash on Windows, you'll find this quick reference indispensable.

  5. Selected, annotated bibliography of studies relevant to the isolation of nuclear wastes. [705 references

    Energy Technology Data Exchange (ETDEWEB)

    Hyder, L.K.; Fore, C.S.; Vaughan, N.D.; Faust, R.A.

    1980-09-01

    This annotated bibliography of 705 references represents the first in a series to be published by the Ecological Sciences Information Center containing scientific, technical, economic, and regulatory information relevant to nuclear waste isolation. Most references discuss deep geologic disposal, with fewer studies of deep seabed disposal; space disposal is also included. The publication covers both domestic and foreign literature for the period 1954 to 1980. Major chapters selected are Chemical and Physical Aspects; Container Design and Performance; Disposal Site; Envirnmental Transport; General Studies and Reviews; Geology, Hydrology and Site Resources; Regulatory and Economic Aspects; Repository Design and Engineering; Transportation Technology; Waste Production; and Waste Treatment. Specialized data fields have been incorporated to improve the ease and accuracy of locating pertinent references. Specific radionuclides for which data are presented are listed in the Measured Radionuclides field, and specific parameters which affect the migration of these radionuclides are presented in the Measured Parameters field. The references within each chapter are arranged alphabetically by leading author, corporate affiliation, or title of the document. When the author is not given, the corporate affiliation appears first. If these two levels of authorship are not given, the title of the document is used as the identifying level. Indexes are provided for author(s), keywords, subject category, title, geographic location, measured parameters, measured radionuclides, and publication description.

  6. An Estimator for Attitude and Heading Reference Systems Based on Virtual Horizontal Reference

    DEFF Research Database (Denmark)

    Wang, Yunlong; Soltani, Mohsen; Hussain, Dil muhammed Akbar

    2016-01-01

    The output of the attitude determination systems suffers from large errors in case of accelerometer malfunctions. In this paper, an attitude estimator, based on Virtual Horizontal Reference (VHR), is designed for an Attitude Heading and Reference System (AHRS) to cope with this problem. The VHR m...

  7. Behind the Appearance of Reference Services at the Library University

    Directory of Open Access Journals (Sweden)

    Lailatur Rahmi

    2018-01-01

    Full Text Available This study aims to describe the development of reference services at the Library of Universitas Indonesia. The research discussed about innovation in the development of new activities in the reference services. Analyzing reference services from librarians’ point of view concerning the new activities in reference services, including attitudes and policies toward activities. This research takes a descriptive qualitative approach and uses semiotic analysis refering to Semiology of Roland Bathes concerning significance from two stage,  denotation and connotation, for analyzing the result of interviews. The results showed that the Universitas Indonesia Library reference service provides some new activities. Librarians become more active, revealed to be closer  to users, and transformation of information technology is seen as one of the competitive need to accompany the development of knowledge. Transfer media eventually have implications not on technology but rather to communication of reference services in the Universitas Indonesia Library.

  8. Behind the Appearance of Reference Services at the Library University

    Directory of Open Access Journals (Sweden)

    Lailatur Rahmi

    2016-12-01

    Full Text Available This study aims to describe the development of reference services at the Library of Universitas Indonesia. The research discussed about innovation in the development of new activities in the reference services. Analyzing reference services from librarians’ point of view concerning the new activities in reference services, including attitudes and policies toward activities. This research takes a descriptive qualitative approach and uses semiotic analysis refering to Semiology of Roland Bathes concerning significance from two stage,  denotation and connotation, for analyzing the result of interviews. The results showed that the Universitas Indonesia Library reference service provides some new activities. Librarians become more active, revealed to be closer  to users, and transformation of information technology is seen as one of the competitive need to accompany the development of knowledge. Transfer media eventually have implications not on technology but rather to communication of reference services in the Universitas Indonesia Library.

  9. From reference to sense: how the brain encodes meaning for speaking

    Directory of Open Access Journals (Sweden)

    Laura eMenenti

    2012-01-01

    Full Text Available In speaking, semantic encoding is the conversion of a nonverbal mental representation (the reference into a semantic structure suitable for expression (the sense. In this fMRI study on sentence production we investigate how the speaking brain accomplishes this transition from nonverbal to verbal representations. In an overt picture description task, we manipulated repetition of sense (the semantic structure of the sentence and reference (the described situation separately. By investigating brain areas showing response adaptation to repetition of each of these sentence properties, we disentangle the neuronal infrastructure for these two components of semantic encoding. We also performed a control experiment with the same stimuli and design but without any linguistic task to identify areas involved in perception of the stimuli per se. The bilateral inferior parietal lobes were selectively sensitive to repetition of reference, while left inferior frontal gyrus showed selective suppression to repetition of sense. Strikingly, a widespread network of areas associated with language processing (left middle frontal gyrus, bilateral superior parietal lobes and bilateral posterior temporal gyri all showed repetition suppression to both sense and reference processing. These areas are probably involved in mapping reference onto sense, the crucial step in semantic encoding. These results enable us to track the transition from nonverbal to verbal representations in our brains.

  10. Multimedia Reference Tools.

    Science.gov (United States)

    Holzberg, Carol S.

    2001-01-01

    Presents suggestions for content-rich classroom encyclopedias on CO-ROM and DVD, including: the Encarta Reference Suite 2001; the 2001 Grolier Multimedia Encyclopedia, School Edition; the Britannica 2001 DVD; and the World Book 2001 Deluxe Edition, v5.0. (SM)

  11. Extending reference assembly models

    DEFF Research Database (Denmark)

    Church, Deanna M.; Schneider, Valerie A.; Steinberg, Karyn Meltz

    2015-01-01

    The human genome reference assembly is crucial for aligning and analyzing sequence data, and for genome annotation, among other roles. However, the models and analysis assumptions that underlie the current assembly need revising to fully represent human sequence diversity. Improved analysis tools...... and updated data reporting formats are also required....

  12. ROOT Reference Documentation

    CERN Document Server

    Fuakye, Eric Gyabeng

    2017-01-01

    A ROOT Reference Documentation has been implemented to generate all the lists of libraries needed for each ROOT class. Doxygen has no option to generate or add the lists of libraries for each ROOT class. Therefore shell scripting and a basic C++ program was employed to import the lists of libraries needed by each ROOT class.

  13. Tracking referents in discourse

    NARCIS (Netherlands)

    Lamers, M.J.A.; Spooren, W.P.M.S.

    2012-01-01

    This reading study registered eye movements to investigate the influence of different discourse constructional factors on anaphor resolution in written discourse. More specifically, the study focused on the influence of the possible interplay of proximity between a possible referent and the anaphor

  14. Reference-Dependent Sympathy

    Science.gov (United States)

    Small, Deborah A.

    2010-01-01

    Natural disasters and other traumatic events often draw a greater charitable response than do ongoing misfortunes, even those that may cause even more widespread misery, such as famine or malaria. Why is the response disproportionate to need? The notion of reference dependence critical to Prospect Theory (Kahneman & Tversky, 1979) maintains that…

  15. Python library reference

    NARCIS (Netherlands)

    G. van Rossum (Guido)

    1995-01-01

    textabstractPython is an extensible, interpreted, object-oriented programming language. It supports a wide range of applications, from simple text processing scripts to interactive WWW browsers. While the Python Reference Manual describes the exact syntax and semantics of the language, it does not

  16. Questions in Reference Interviews.

    Science.gov (United States)

    White, Marilyn Domas

    1998-01-01

    Characterizes the questioning behavior in reference interviews preceding delegated online searches of bibliographic databases and relates it to questioning behavior in other types of interviews/settings. Compares questions asked by the information specialist and those asked by the client; findings show the information specialist dominates the…

  17. Genetics Home Reference: bradyopsia

    Science.gov (United States)

    ... they often have trouble watching or participating in sports with a ball, such as soccer or tennis. ... IAE.0b013e31827e2306. Review. Citation on PubMed More from Genetics Home Reference Bulletins Rare Disease Day 2018 Darwin ...

  18. Generating Multimodal References

    NARCIS (Netherlands)

    van der Sluis, Ielka; Krahmer, E.

    2007-01-01

    This paper presents a new computational model for the generation of multimodal referring expressions, based on observations in human communication. The algorithm is an extension of the graph-based algorithm proposed by Krahmer et al. (2003) and makes use of a so-called Flashlight Model for pointing.

  19. Synthetic growth reference charts

    NARCIS (Netherlands)

    Hermanussen, Michael; Stec, Karol; Aßmann, Christian; Meigen, Christof; Van Buuren, Stef|info:eu-repo/dai/nl/074806777

    2016-01-01

    Objectives: To reanalyze the between-population variance in height, weight, and body mass index (BMI), and to provide a globally applicable technique for generating synthetic growth reference charts. Methods: Using a baseline set of 196 female and 197 male growth studies published since 1831, common

  20. Pollen reference collection digitization

    NARCIS (Netherlands)

    Ercan, F.E.Z.|info:eu-repo/dai/nl/41250085X; Donders, T.H.|info:eu-repo/dai/nl/290469872; Bijl, P.K.|info:eu-repo/dai/nl/314028110; Wagner, F.|info:eu-repo/dai/nl/173870783

    2016-01-01

    The extensive Utrecht University pollen reference collection holds thousands of pollen samples of many species and genera from all over the world and has been a basis for the widely-used North West European Pollen Flora. These samples are fixed on glass slides for microscopy use, but the aging