Direct Flotation of Niobium Oxide Minerals from Carbonatite Niobium Ores

Science.gov (United States)

Ni, Xiao

Currently the recovery of niobium oxide minerals from carbonatite niobium ores relies on the use of non-selective cationic collectors. This leads to complicated process flowsheets involving multiple desliming and multiple reverse flotation stages, and low niobium recovery. In this research, anionic collectors that are capable of strong chemisorption on the niobium minerals were studied with the objective of directly floating the niobium oxide minerals from the carbonatite ores. In the flotation of both high purity minerals and Niobec ores, it was shown that the combination of hydroxamic acid and sodium metaphosphate was an effective reagent scheme for the direct flotation of niobium oxide from its ores. Batch flotation on the Niobec Mill Feed showed that over 95% of niobium oxide was recovered into a rougher concentrate that was less than 47% of the original feed mass. Preliminary cleaning tests showed that the reagent scheme could also be used to upgrade the rougher concentrate, although the depression of iron oxide minerals required further study. X-ray photoelectron spectroscopic (XPS) measurement results confirm that OHA (octyl hydroxamic acid) could chemisorb on pyrochlore surface while only physically adsorb on calcite, judging by the chemical shifts of electron binding energies in the elements in both OHA and the mineral surfaces. When hydroxamic acid was adsorbed on calcite surface, the binding energies of the N 1s electrons, at 400.3 eV, did not shift. However, after adsorption on pyrochlore, the N 1s binding energy peak split into two peaks, one at a binding energy of around 399 eV, representing chemically adsorbed OHA, the other at between 400 and 401 eV. The experimental data suggested a strong chemisorption of the OHA on pyrochlore surface in the form of a vertical head-on orientation of the OHA molecules so that the pyrochlore was strongly hydrophobized even at low OHA concentrations, followed by possibly randomly oriented physisorbed OHA molecules

Studies of leaching of copper ores and flotation wastes

International Nuclear Information System (INIS)

Wawszczak, D.; Deptula, A.; Lada, W.; Smolinski, T.; Olczak, T.; Brykala, M.; Wojtowicz, P.; Rogowski, M.; Milkowska, M.; Chmielewski, A.G.

2014-01-01

In Poland, there are significant deposits of copper ores. During the copper extraction, large amounts of flotation wastes are produced. In the ores and flotation wastes many other important elements are present. The main goal of this work was analysis of uranium content and to elaborate procedures for recovery of U from these materials. Two types of ores and four types of waste were examined. It has been found that uranium content varies from 4.5 to 25 ppm. The other elements have also been determined in these materials: Cu (4-5 % in ores and 0.3-1.7 % in waste), Ag, Re, Mo, La, Ni, V, etc. For leaching, sulfuric acid and sodium carbonates of various concentrations (temperature, time) were used. The optimum conditions for leaching have been found. The concentration of uranium in the final solution was generally less than 25 μg/mL. The other elements are also present in the leaching solutions. Simultaneous liquid-liquid extraction of uranium with these elements from leaching solution is under study. In our opinion, only such combined procedure for the recovery of uranium together with the accompanying elements could be cost-effective. (author)

Gold-copper ores processing-Case study: optimization of flotation residue cyanidation

International Nuclear Information System (INIS)

McMullen, J.; Pelletier, P.; Breau, Y.; Pelletier, D.

1999-01-01

Typically, economic optimization of Gold-Copper ore processing presents challenges. Barrick's Bousquet II ore is a good example where many processing units such as gravity, flotation and cyanidation are required to efficiently recover the metals from the ore. Flowsheet criterion, operating strategy selections, cyanidation process optimization and its inter-dependence with flotation are discussed in detail. Real-time conservation integration of the cyanide control strategy has allowed a reduction of cyanide consumption of over 40% since 1994, while maintaining or improving metals recovery. A detailed analysis of the cyanidation control strategy such as key process sensor reliability and accuracy, process monitoring and fault detection is presented. This robust and efficient control strategy is a key building block that enhances the overall economic return of the process plant. (author)

Effects of High Pressure ORE Grinding on the Efficiency of Flotation Operations

Science.gov (United States)

Saramak, Daniel; Krawczykowska, Aldona; Młynarczykowska, Anna

2014-10-01

This article discusses issues related to the impact of the high pressure comminution process on the efficiency of the copper ore flotation operations. HPGR technology improves the efficiency of mineral resource enrichment through a better liberation of useful components from waste rock as well as more efficient comminution of the material. Research programme included the run of a laboratory flotation process for HPGR crushing products at different levels of operating pressures and moisture content. The test results showed that products of the high-pressure grinding rolls achieved better recoveries in flotation processes and showed a higher grade of useful components in the flotation concentrate, in comparison to the ball mill products. Upgrading curves have also been marked in the following arrangement: the content of useful component in concentrate the floatation recovery. All upgrading curves for HPGR products had a more favourable course in comparison to the curves of conventionally grinded ore. The results also indicate that various values of flotation recoveries have been obtained depending on the machine operating parameters (i.e. the operating pressure), and selected feed properties (moisture).

The effect of process water salinity on flotation of copper ore from Lubin mining region (SW Poland

Directory of Open Access Journals (Sweden)

Bakalarz Alicja

2017-01-01

Full Text Available The process water used for the flotation of sedimentary copper ore in ore concentration plants in KGHM Polska Miedz S.A. were characterized. The process water used in the flotation circuits is heavily saline. It contains between 25 and 45 g/dm3 of soluble components, and the main constituent, in about 75%, is NaCl. Process water used for flotation consists of reclaimed water from the tailing dam and mine water. The effect of process water salinity on the processes of copper flotation from the Lubin mine area was described. The results of laboratory flotation experiments conducted in tap water and in water of different salinity levels were compared. The effect of the salinity of water within specified concentration limits was generally found to be beneficial for upgrading of the examined ore.

Improvement of ore recovery efficiency in a flotation column cell using ultra-sonic enhanced bubbles

Science.gov (United States)

Filippov, L. O.; Royer, J. J.; Filippova, I. V.

2017-07-01

The ore process flotation technique is enhanced by using external ultra-sonic waves. Compared to the classical flotation method, the application of ultrasounds to flotation fluids generates micro-bubbles by hydrodynamic cavitation. Flotation performances increase was modelled as a result of increased probabilities of the particle-bubble attachment and reduced detachment probability under sonication. A simplified analytical Navier-Stokes model is used to predict the effect of ultrasonic waves on bubble behavior. If the theory is verified by experimentation, it predicts that the ultrasonic waves would create cavitation micro-bubbles, smaller than the flotation bubble added by the gas sparger. This effect leads to increasing the number of small bubbles in the liquid which promote particle-bubble attachment through coalescence between bubbles and micro-bubbles. The decrease in the radius of the flotation bubbles under external vibration forces has an additional effect by enhancing the bubble-particle collision. Preliminary results performed on a potash ore seem to confirm the theory.

Upgrading of boron ores and colemanite flotation

International Nuclear Information System (INIS)

Yarar, B.; Mager, J.

1979-01-01

Processes applied for the processing and upgrading of sodium and calcium borates in Turkey are described. Details of froth flotation study where a low grade colemanite ore containing calcite and clays as a gangue minerals are given. It has been found that, at the natural pH of a colemanite-containing pulp (pH=9,2) it is possible to float colemanite selectively using dodecyl benzene sulphonate or its combinations with a non-polar reagent or naphthenic acids. (author)

CHAIN EXTENDER AND EMULSIFIER APPLICATION IN IRON ORE FLOTATION

Directory of Open Access Journals (Sweden)

José Pedro da Silva

2013-06-01

Full Text Available The present study aims to evaluate the reverse flotation performance of iron ore, using collector (amine, in the presence and absence of chain extender (diesel oil and emulsifier (sodium lauryl sulfate.Six tests were realized with duplicate. Tests using amine, diesel oil and sodium lauryl sulphate show the better results, with metallurgical recovery of 91.82% and the concentrate silica equal 1.68%. Thus, it is found that the use of emulsifier and chain extender together with the amine, shows better results in the flotation, in terms of metal recovery and selectivity, when compared to using only amine or amine and diesel oil.

Beneficiation of a Sedimentary Phosphate Ore by a Combination of Spiral Gravity and Direct-Reverse Flotation

Directory of Open Access Journals (Sweden)

Xin Liu

2016-04-01

Full Text Available In China, direct-reverse flotation is proved to be applicable to most phosphate ores. However, because the ratio of froth product is generally high, current direct-reverse technology faces challenges in terms of high reagent consumptions and cost. A new gravity and flotation combined process has been developed for the recovery of collophanite from sedimentary phosphate ore from the beneficiation plant of Hubei, China. In this process, 53% of the collophanite was firstly recovered by gravity separation, reducing the mass flow to direct flotation. The gravity tailing was the feed for the direct flotation. The flotation concentrate, mixed with gravity concentrate, was then subjected to reverse flotation. A final concentrate with a grade of 30.41% P2O5 at a recovery of 91.5% was produced from the feed analyzing 21.55% P2O5. Compared to the conventional direct-reverse flotation 86.1% recovery at 31.69% P2O5, it was found that pre-recovery of collophanite by spiral separation could significantly reduce the flotation reagent consumption and lead to improved overall collophanite recovery. The benefits of the new process in terms of cost savings were also discussed.

The flotation of gold, uranium, and pyrite from Witwatersrand ores

International Nuclear Information System (INIS)

Lloyd, P.J.D.

1981-01-01

The Witwatersrand reefs contain gold, uranium, and pyrite in the following average concentrations: 0,001 per cent, 0,02 per cent, and 1,7 per cent respectively. The paper discusses the flotation of pyrite to produce a sulphide concentrate, reviews work done on the production of gold concentrates, discusses attempts to produce maximum concentrates, and closes with a review of processes for the simultaneous flotation of these three species. It is concluded that high recoveries of all three species can be achieved only if a rougher concentrate of perhaps 20 per cent of the feed (by mass) is produced, and it is suggested that reverse leaching (leaching before cyanidation) of this concentrate, followed by a cleaning flotation step for the recovery of the pyrite, would be more efficient than the routes employed at present [af

Investigation of impact of water type on borate ore flotation.

Science.gov (United States)

Ozkan, S G; Acar, A

2004-04-01

In this work, the impact of water type on borate ore flotation was investigated, while various physical parameters during flotation were considered in order to compare the results. Two different colemanite samples from Emet deposits of Turkey, named as Emet-A and Emet-B contained 44% B(2)O(3) and 40% B(2)O(3), respectively. The flotation tests were performed at feed particle size range of -210 +20 microm. Optimal consumption values for the reagents were determined as 2000 gt(-1) for AeroPromoter R825 from Cytec Company, a sulphonate type collector, 1500 gt(-1) for Procol CA927 from Allied Colloids Company, a sulphosuccinamate type collector and 100 gt(-1) for AeroFrother 70 from Cytec Company, an alcohol-type frother. In the tests, the impeller speed of the Denver-type flotation machine was set to 1200 rpm and the samples were fed into a litre cell at 25% solid/liquid ratio and at natural pH value of the slurry at room temperature. The flotation results obtained from the tests with use of tap water, demineralised water and the artificial water prepared with Ca(2+) and Mg(2+) cations deliberately added into demineralised water were compared to each other in optimal flotation conditions.

Effect of desliming on the flotation of a complax copper ore from China

Directory of Open Access Journals (Sweden)

Chen Yong

2016-01-01

Full Text Available The complex copper oxide ore sample was taken from Deerni copper deposit, Qinghai Province of China. Batch flotation tests had been conducted to upgrade the copper concentrate by conventional amyl xanthate reagents under 73% -74 μm of the particle size; however, the unsatisfied results (Cu grade of 18.21% and recovery of 59.25% were obtained. Also there are a large amount of slimes trapped in the concentrate and high-dosages consumption of reagents, for example, more than 2.5 kg/t sodium sulfide and 1.5 kg/t sodium silicate at only one-staged roughing. Based on the analysis of the sample, most of gangues are clay, feldspar and mica, which may easy to over-grind and deteriorate the flotation process either on reagents consumption or slurry fluidity or viscosity. A hydro-cyclone had been introduced to pre-concentrate the oxide ore by scrubbing the slime before flotation, which can result obviously in reducing the dosages of sodium sulfide from 2.5 Kg/t to 1 Kg/t, and raising the grade of Cu in the concentrate from 18.21% to 26.65% at the expense of about 1% recovery of Cu. In this paper, the effects on the recovery of Cu by the different dosages of flotation reagents with or without de-sliming were studied, with the objective of determining the different effects on the functions of flotation reagents by slime during flotation.

A multidimensional analysis and modelling of flotation process for selected Polish lithological copper ore types

Directory of Open Access Journals (Sweden)

Niedoba Tomasz

2017-01-01

Full Text Available The flotation of copper ore is a complex technological process that depends on many parameters. Therefore, it is necessary to take into account the complexity of this phenomenon by choosing a multidimensional data analysis. The paper presents the results of modelling and analysis of beneficiation process of sandstone copper ore. Considering the implementation of multidimensional statistical methods it was necessary to carry out a multi-level experiment, which included 4 parameters (size fraction, collector type and dosage, flotation time. The main aim of the paper was the preparation of flotation process models for the recovery and the content of the metal in products. A MANOVA was implemented to explore the relationship between dependent (β, ϑ, ε, η and independent (d, t, cd, ct variables. The design of models was based on linear and nonlinear regression. The results of the variation analysis indicated the high significance of all parameters for the process. The average degree of matching of linear models to experimental data was set at 49% and 33% for copper content in the concentrate and tailings and 47% for the recovery of copper minerals in the both. The results confirms the complexity and stochasticity of the Polish copper ore flotation.

Study on the pre-treatment of oxidized zinc ore prior to flotation

Science.gov (United States)

He, Dong-sheng; Chen, Yun; Xiang, Ping; Yu, Zheng-jun; Potgieter, J. H.

2018-02-01

The pre-treatment of zinc oxide bearing ores with high slime content is important to ensure that resources are utilized optimally. This paper reports an improved process using hydrocyclone de-sliming, dispersion reagents, and magnetic removal of iron minerals for the pre-treatment of zinc oxide ore with a high slime and iron content, and the benefits compared to traditional technologies are shown. In addition, this paper investigates the damage related to fine slime and iron during zinc oxide flotation, the necessity of using hydrocyclone de-sliming together with dispersion reagents to alleviate the influence of slime, and interactions among hydrocyclone de-sliming, reagent dispersion, and magnetic iron removal. Results show that under optimized operating conditions the entire beneficiation technology results in a flotation concentrate with a Zn grade of 34.66% and a recovery of 73.41%.

Flotation of zinc and lead oxide minerals from Olkusz region calamine ores

Directory of Open Access Journals (Sweden)

Cichy Krystian

2016-01-01

Full Text Available The paper presents chemical and mineralogical characteristics of calamine ore from the Pomorzany mine. A flowsheet for recovery of sulphide minerals of zinc and lead in the form of the Zn-Pb bulk concentrate was presented. In the following part, preparation of the feed for flotation of Zn-Pb oxide minerals and optimal conditions for separation from it iron sulphide minerals, represented by marcasite, were determined. In the final section the results of flotation of Zn-Pb oxide minerals with anionic collector AM2 belonging to the hydroxyamide group of collectors and a cationic collector in the form of a coconut amine, being a mixture of primary aliphatic amines, were presented. Basing on the obtained results, a technological flowsheet for the recovery of Zn-Pb sulphide and oxide minerals from the calamine ore of the Pomorzany mine was presented.

Quantitative analysis and automation of CaF2 ore flotation via neutronic activation

International Nuclear Information System (INIS)

Reggiani, F.; Garagnani, A.; Lembo, L.; Muntoni, C.

1992-01-01

The aim of the project was to prove the operative feasibility of an 'one line analysis' based on nuclear activation using 14 MeV neutrons. This on line analysis method was to be used to automate control of the flotation process for ores containing mostly fluorspar. The thermoluminescence technique was also forecast as a subsidiary method in those points of the flotation cycle where less precision is acceptable. (author). 11 figs., 4 tabs

Extraction of a Low Grade Zinc Ore using Gravity and Froth Flotation ...

African Journals Online (AJOL)

ADOWIE PERE

ABSTRACT: Extraction of low grade zinc ore found in Gumau- Toro town was carried out using gravity and froth flotation methods. .... And to determine the best separation ..... Wet De, K; Singleton, J.D (2008) Development of a. Viable Process ...

Acid leaching of oxide-sulphide copper ore prior the flotation: A way for an increased metal recovery

Directory of Open Access Journals (Sweden)

Sokić Miroslav D.

2015-01-01

Full Text Available Copper mine "Cerovo"- East Serbia as well as the other ore bodies in its vicinity contain a significant amount of oxide copper minerals in their uper layers (>40%. Processing of such mixed ores by the existing concentration technologies leads to a substantial copper losses (<60%. Reduction of "oxide copper", by acid leaching prior the flotation concentration, can increase the overall copper efficiency up to more than 70% in the single-stage leaching, achieving an efficiency in the flotation concentration stage higher than 75%. Based on the performed experimental results the flow sheet for processing of the mixed oxide-sulphide copper ore is proposed.

The nature of hematite depression with corn starch in the reverse flotation of iron ore.

Science.gov (United States)

Shrimali, Kaustubh; Atluri, Venkata; Wang, Yan; Bacchuwar, Sanket; Wang, Xuming; Miller, Jan D

2018-08-15

The function of corn starch and the significance of the order of addition of corn starch and mono ether amine in the reverse flotation of iron ore has been investigated. Understanding hematite depression with starch and the corresponding hydrophilic state involves consideration of adsorption with amine as well as flocculation of fine hematite. Captive bubble contact angle and micro-flotation experiments indicated that amine has an affinity towards both hematite and quartz, and that the role of starch is to hinder the adsorption of amine at the hematite surface so that flotation is inhibited. Micro-flotation results confirmed that quartz does not have affinity towards starch at pH 10.5. In addition to competitive adsorption, flocculation of fine hematite occurs and images from high resolution X-ray computed tomography (HRXCT) and cryo-SEM reveal further detail regarding floc structure. These results provide substantial evidence that the fine hematite particles are flocculated in the presence of corn starch, and flocculation is dependent on the particle size of hematite, with greater flocculation for finer particles. Thus, starch is playing a dual role in the reverse flotation of iron ore, acting as a depressant by hindering amine adsorption at the hematite surface in order to maintain the hydrophilic surface state of hematite, and acting as a flocculant to aggregate fine hematite particles, which if not flocculated, could diminish the flotation separation efficiency by being transported to the froth phase during reverse flotation. Copyright © 2018 Elsevier Inc. All rights reserved.

Concentration of gold, sulphide minerals, and uranium oxide minerals by flotation from ores and metallurgical plant products

International Nuclear Information System (INIS)

Weston, D.

1976-01-01

A process is described for the concentration by flotation of gold, gold bearing minerals and uranium oxide minerals from ores and metallurgical plant products. A pulp of a ground ore is agitation conditioned in at least two agitation conditioning stages wherein in at least one stage the pH of the pulp is lowered with an acid agent to within the pH range of about 1.5 to 5.0, and wherein in at least one additional agitation conditioning stage the pH of the pulp is raised to within the pH range of about 6.0 to 11.0 and wherein in at least the last stage prior to flotation at least one collector selected from the group of sulfhydryl anionic collectors is present. Subsequently, the at least two stage agitation conditioned pulp is subjected to flotation to produce a flotation concentrate enriched in at least one of the mineral values from the group consisting of gold, gold bearing minerals and uranium minerals

High-performance reagent modes for flotation recovery of platiniferous copper and nickel sulfides from hard-to-beneficiate ores

Science.gov (United States)

Matveeva, T. N.; Chanturiya, V. A.

2017-07-01

The paper presents the results of the recent research performed in IPKON Russian Academy of Sciences that deals with development and substantiation of new selective reagents for effective flotation recovery of non-ferrous and noble metals from refractory ores. The choice and development of new selective reagents PTTC, OPDTC, modified butylxanthate (BXm) and modified diethyl-dithiocarbamate (DEDTCm) to float platiniferous copper and nickel sulfide minerals from hard-to-beneficiate ores is substantiated. The mechanism of reagents adsorption and regulation of minerals floatability is discussed. The study of reagent modes indicates that by combining PTTC with the modified xanthate results in 6 - 7 % increase in the recovery of copper, nickel and PGM in the flotation of the low-sulfide platiniferous Cu-Ni ore from the Fedorovo-Panskoye deposit. The substitution of OPDTC for BX makes it possible to increase recovery of Pt by 13 %, Pd by 9 % and 2 - 4 times the noble metal content in the flotation concentrate.

Flotation study on scheelite ore of chitral khyber pakhtoonkhwa, pakistan

International Nuclear Information System (INIS)

Bhatti, M.A.; Kazmi, K.R.; Mehmood, R.; Akram, A.

2014-01-01

The beneficiation of a siliceous scheelite ore of Chitral, Khyber Pakhtoonkhwa, Pakistan, was investigated by flotation process to determine the optimum conditions for obtaining maximum grade and recovery of the scheelite concentrate. The variables studied were including pH and pulp density maintained during conditioning, type and quantity of reagents added, conditioning time and froth collecting time. The results achieved were plotted against the grade and recovery of the rougher concentrate. Several methods of cleaning rougher concentrate were attempted. An ore initially containing 0.34% WO/sub 3/ was upgraded into a final concentrate assaying 64.66% WO/sub 3/ with 70.36% recovery. The tungsten concentrate obtained meets the specifications required to produce ferrotungsten and tungsten chemicals. (author)

Nickel Ore Dispersion Evaluation and Consequences in Flotation Process

Science.gov (United States)

de São José, Fábio; Imbelloni, Alaine Moreira; Nogueira, Francielle Câmara; Pereira, Carlos Alberto

2016-04-01

Nickel ore dispersion before flotation using different reagents was investigated on a bench scale to improve metallurgical recovery and selectivity. The nickel ore had a content of 0.8 pct nickel and 14.5 pct MgO. A positive linear correlation between MgO and Ni was found. Carboxy methyl cellulose, both pure and combined with Na2CO3, was the best dispersant used. The most efficient collector was potassium amyl xanthate combined with mercaptobenzothiazole, and the addition of xanthate was decisive for this good result because it is normally more stable in the pH range used in the tests. A pH change from 7 to 9 resulted in a metal recovery increase of 49.3 pct, together with an increase of 6.25 pct of MgO in the concentrate.

Influence of a High-Pressure Comminution Technology on Concentrate Yields in Copper Ore Flotation Processes

Directory of Open Access Journals (Sweden)

Saramak D.

2014-10-01

Full Text Available The article concerns the issues of flotation process effectiveness in relationship to the operating conditions of a high-pressure comminution process course. Experimental programme covering a flotation laboratory batch tests was a verification technique of a high-pressure crushing operations course. The most favorable values of flotation concentrate weight recoveries were obtained for the pressing force 6 kN and 4% of the feed moisture. It was also determined the model of the concentrate weight recovery as a function of pressing force in the press and feed moisture content. This model was the basis for the optimization of effects of copper ore flotation processes preceded in high-pressure crushing operation in roller presses.

Copper Recovery from Yulong Complex Copper Oxide Ore by Flotation and Magnetic Separation

Science.gov (United States)

Han, Junwei; Xiao, Jun; Qin, Wenqing; Chen, Daixiong; Liu, Wei

2017-09-01

A combined process of flotation and high-gradient magnetic separation was proposed to utilize Yulong complex copper oxide ore. The effects of particle size, activators, Na2S dosage, LA (a mixture of ammonium sulfate and ethylenediamine) dosage, activating time, collectors, COC (a combination collector of modified hydroxyl oxime acid and xanthate) dosage, and magnetic intensity on the copper recovery were investigated. The results showed that 74.08% Cu was recovered by flotation, while the average grade of the copper concentrates was 21.68%. Another 17.34% Cu was further recovered from the flotation tailing by magnetic separation at 0.8 T. The cumulative recovery of copper reached 91.42%. The modifier LA played a positive role in facilitating the sulfidation of copper oxide with Na2S, and the combined collector COC was better than other collectors for the copper flotation. This technology has been successfully applied to industrial production, and the results are consistent with the laboratory data.

Influence of Froth Height on Column Flotation of Kaolin Ore

Directory of Open Access Journals (Sweden)

Fernando Pita

2017-11-01

Full Text Available The influence of the froth height in the reverse flotation of kaolinitic ore was analyzed based on the recovery by entrainment and by true flotation of iron, titanium and manganese oxides (FeO, TiO2 and MnO. Also, the influence of the particle size in the drainage process was analyzed. The recovery by entrainment and by true flotation of the three oxides is inversely proportional to the froth height. The entrained particles are drained more easily in the froth phase than the floated particles since they are not attached to the bubbles. The recovery by entrainment and drainage of the entrained material is similar for the three oxides. However, the recovery by true flotation and drainage of the floated material is different for the three oxides. FeO has the lowest recovery, as a consequence of the minor contribution of its hydrophobic minerals, while MnO has the greatest recovery values. For the entrained material, the finest fraction is entrained more easily, but it is also drained more easily, meaning these particles have more mobility in the froth zone. For the true floated material, the finest fraction is drained more easily, indicating the greater mobility of these particles in the froth; however, the coarsest fraction is drained more easily than the two intermediate fractions, indicating the weaker attachment of the larger particles to the bubbles.

Recovery of uranium low grade ores by froth flotation: study of the texture and synergetic effects of flotation reagents

International Nuclear Information System (INIS)

Duverger, Agathe

2013-01-01

Due to the energy growing demand, uranium low grade ores may be those exploited in the future. Uranium ores conventional treatment does not often use mineral processing such as concentration methods for reducing leaching reagent consumption. The aim of this work is to develop an upgrading process to improve the operating process (alkaline heap leaching) taking into account the mineralogical and textural variability of the ore. The Trekkopje deposit is composed of calcrete and a gypscrete. The uranium bearing mineral is carnotite (K 2 (UO 2 ) 2 [VO 4 ] 2 .3H 2 O). The gangue minerals are composed by silicates, such as quartz, feldspars, micas and Ca-minerals, calcite and gypsum (XRD and ICP-MS analysis). A SEM image processing was used to study the textural properties and the exposed free surface of mineral inclusions in clay clusters. In calcrete milled to -200 μm, 50 % of all carnotite is associated with clay clusters, which are composed by 98 % of palygorskite, 2 % of illite, montmorillonite, and interbedded clays (XRD and microprobe analysis). The carnotite grain size is 95 % less than 70 μm. Calcite is the main inclusion in clay clusters. Indeed, the calcite inclusions average rate in the clay clusters is 12 % and 5 % for carnotite inclusion. And the free exposed surface percentage of these minerals in clay clusters is 3 % and 6 %, thus indicating that the inclusions should not affect the behavior of mixed clay particles. However, ore flotation essays did not verify this hypothesis. Three minerals separation have been proposed based on the mineral ability to consume leaching reagents: separating Ca-minerals from silicates, palygorskite from gangue minerals and carnotite from gangue minerals. A study of silicates and Ca-minerals electrokinetic properties (electrophoresis) was carried out to select the collectors and the optimum pH range for selective flotation. Basic pH near neutral was proved to be optimal for the separation of gangue minerals with cationic

Estimated water requirements for the conventional flotation of copper ores

Science.gov (United States)

Bleiwas, Donald I.

2012-01-01

This report provides a perspective on the amount of water used by a conventional copper flotation plant. Water is required for many activities at a mine-mill site, including ore production and beneficiation, dust and fire suppression, drinking and sanitation, and minesite reclamation. The water required to operate a flotation plant may outweigh all of the other uses of water at a mine site, [however,] and the need to maintain a water balance is critical for the plant to operate efficiently. Process water may be irretrievably lost or not immediately available for reuse in the beneficiation plant because it has been used in the production of backfill slurry from tailings to provide underground mine support; because it has been entrapped in the tailings stored in the TSF, evaporated from the TSF, or leaked from pipes and (or) the TSF; and because it has been retained as moisture in the concentrate. Water retained in the interstices of the tailings and the evaporation of water from the surface of the TSF are the two most significant contributors to water loss at a conventional flotation circuit facility.

The flotation of Roşia Poieni copper ore in column machine, with non-polar oils addition

Directory of Open Access Journals (Sweden)

Ciocani V.

2005-11-01

Full Text Available The most important natural resource of copper in Romania is the ore deposit of Roşia Poieni. At present, the utilization of Roşia Poieni poorphyry copper ore is possible by extraction in quarry of the mass ore and mineral processing into a technological flux with modest results for the value of metal recovery in concentrate 70-72 % and an average contents of 16,5 % Cu. Our researches were directed to studies regarding test and utilisation of special procedure of flotation – addition of the non-polar oil – applied to advanced grinding ore with column type machines.

Non-cyanide process for flotation of a uranium-bearing lead-zinc polymetallic sulphide ore

International Nuclear Information System (INIS)

Li Qingxin

1988-01-01

The characteristics of the minerals of a urnium-bearing lead-zinc ore are described in this paper, And the experimentsl results of non-cyanide flotation process are given. The tests show that the selective flotation process of lead and zinc followed by uranium treatment is feasible in technology and reasonable in economics. When the run-of-mine contains 2.86%Pb, 2.47%Zn and 0,019%U, the lead concentrate containing 65.13%Pb, and 4.51%Zn, the zinc concentrate containing 52.00%Zn and 1.22%Pb, and the uranium concentrate containing 0.028%U can be obtained with the recoveries of 94.87%Pb, 87.61%Zn and 66.13%U respectively. The influence of sodium sulphite on flotaion process, the effect of sodium sulphite and the flotation mechanism of dibutyldithiophosphate ammonium are also discussed

Reagent conditions of the flotation of copper, copper - molybdenum and copper -zinc ores in foreing countries

International Nuclear Information System (INIS)

Nevaeva, L.M.

1983-01-01

Reagents-collectors and frothers, used abroad in reagent regimes of flotation of copper, copper-molybdenum and copper zinc ores, have been considered. Xanthogenates, aerofloats, xanthogenformiates, thionocarbamates are mainly used as reagents-collectors. Methylizobutylcarbinol and Daufros are used as reagents-frothers

The critical importance of pulp concentration on the flotation of galena from a low grade lead–zinc ore

Directory of Open Access Journals (Sweden)

Xianping Luo

2016-04-01

Full Text Available The Qixia orebody is a complex lead–zinc sulfide system with pyrite gangue and minor amounts of copper. In order to improve the flotation results, laboratory scale flotation testing of ore samples taken from this operation was performed. Flotation tests used a sequential recovery protocol for selective flotation of first the lead and thereafter the zinc. The key parameters that influence flotation performance of lead mineral were tested in this paper. The test data show that, for comparable collector, grinding time, flotation pH and solid-in-pulp concentration, the increase of solid-in-pulp concentration has the most significant effect on the recovery and selective separation of lead mineral. The increase of solid-in-pulp concentration from 27% to 55% makes the recovery of lead mineral increased from 60% to 80% and the lead grade increased from 27.5% to 29.1%.

Development of a composite collector scheme for flotation of chalcopyrite ore

International Nuclear Information System (INIS)

Khan, M.M.; Ahmad, I.

2005-01-01

Xanthate-type collectors reported for the upgradation of Chalcopyrite ore of North Waziristan area were studied and a new technique was developed, in which -two collectors were used (composite collectors) in the bulk-stage process of froth-flotation to achieve metallurgical grade with maximum recovery. The collectors studied were thiol-type surfactants, such as sodium ethyl xanthate (NaEX), sodium propyl xanthate (NaPX), sodium butyl xanthate (NaBX) and sodium Amyl xanthate (NaAX). Mixed collectors examined were in the varying dosage ratio of (0-100:100-0) through the combination of(i) sodium ethyl xanthate with sodium propyl xanthate, sodium ethyl xanthate with sodium butyl xanthate, sodium ethyl xanthate with sodium amyl xanthate, (ii) sodium propyl xanthate with sodium butyl xanthate, sodium propyl xanthate with sodium amyl xanthate and (iii) sodium butyl xanthate with sodium amyl xanthate. All the remaining flotation parameters were kept constant during the various flotation tests. The results were compared and the conclusions were drawn that the optimum grade in the concentrate was obtained with a mixture having a ratio of 4: 1 with sodium ethyl xanthate and sodium butyl xanthate. Recovery of copper content in the concentrate was achieved with ratio of 2:3 with sodium butyl xanthate and sodium amyl xanthate. (author)

A Multistage Sulphidisation Flotation Procedure for a Low Grade Malachite Copper Ore

OpenAIRE

Tebogo P. Phetla; Edison Muzenda

2010-01-01

This study was carried out to develop a flotation procedure for an oxide copper ore from a Region in Central Africa for producing an 18% copper concentrate for downstream processing at maximum recovery from a 4% copper feed grade. The copper recoveries achieved from the test work were less than 50% despite changes in reagent conditions (multistage sulphidisation, use of RCA emulsion and mixture, use of AM 2, etc). The poor recoveries were attributed to the mineralogy of t...

Treatment and Recycling of the Process Water in Iron Ore Flotation of Yuanjiacun Iron Mine

Directory of Open Access Journals (Sweden)

Wen-li Jiang

2017-01-01

Full Text Available Coagulating sedimentation and oxidation treatment of process water in iron ore flotation of Yuanjiacun iron mine had been studied. The process water of this mine carried residual polyacrylamide (PAM, poly(diallyldimethylammonium chloride (PDADMAC, and Ca2+ from the flotation and caused decrease of the iron flotation recovery or grade of the concentrate. The studies on high-intensity magnetic separation (HIMS tailings for coagulating sedimentation showed that the settling performance of coagulant (named CYH was better than that of PDADMAC. The analyses of FTIR spectra and zeta potential demonstrated that CYH is adsorbed mainly through electrostatic attraction onto HIMS tailings. Sodium hypochlorite was adopted to oxidize the residual organics in tailings wastewater. When sodium hypochlorite is at the dosage of 1.0 g/L, reaction temperature is of 20°C, and reaction time is of 30 minutes, the removal rates of PAM, COD, and Ca2+ were 90.48%, 83.97%, and 85.00%, respectively. Bench-scale flotation studies on the treated tailings wastewater indicated that the iron recovery and grade of concentrate were close to those of freshwater.

Recovery of copper and precious metals from chalcopyrite low grade ores - choice between flotation or microorganisms leaching

OpenAIRE

Krstev, Boris; Golomeov, Blagoj; Konzulov, Gerasim; Gocev, Zivko

1998-01-01

The conventional flotation technologies cannot provide fair results when to applied to very low grade ores or to "refractory" ores. This class include intimate and nonuniform mineral associations, with partialy oxidized minerals and high secondary mineral content and also high soluble salt content, pre-activated minerals because of the excessive permeability of the deposit and of the intense circulation of waters with heavy metal ions etc. Bacterial oxidation as a means to the recovery of met...

Assessment of the flotability of chalcopyrite, molybdenite and pyrite using biosolids and their main components as collectors for greening the froth flotation of copper sulphide ores.

OpenAIRE

Sobarzo, Francisco; Herrera Urbina, Ronaldo; Higueras Higueras, Pablo Leon; Sáez Navarrete, César; Godoy Faúndez, Alex; Reyes Bozo, Lorenzo; Vásquez Bestagno, Jorge

2014-01-01

Biosolids and representative compounds of their main components ? humic acids, sugars, and proteins ? have been tested as possible environment-friendly collectors and frothers for the flotation of copper sulphide ores. The floatability of chalcopyrite and molybdenite ? both valuable sulphide minerals present in these ores ? as well as non-valuable pyrite was assessed through Hallimond tube flotation tests. Humic acids exhibit similar collector ability for chalcopyrite and molybdenite as that ...

Solvent extraction of Cu, Mo, V, and U from leach solutions of copper ore and flotation tailings

International Nuclear Information System (INIS)

Smolinski, Tomasz; Wawszczak, Danuta; Deptula, Andrzej; Lada, Wieslawa; Olczak, Tadeusz; Rogowski, Marcin; Pyszynska, Marta; Chmielewski, Andrzej Grzegorz

2017-01-01

Flotation tailings from copper production are deposits of copper and other valuable metals, such as Mo, V and U. New hydrometallurgical technologies are more economical and open up new possibilities for metal recovery. This work presents results of the study on the extraction of copper by mixed extractant consisting p-toluidine dissolved in toluene. The possibility of simultaneous liquid-liquid extraction of molybdenum and vanadium was examined. D2EHPA solutions was used as extractant, and recovery of individual elements compared for the representative samples of ore and copper flotation tailings. Radiometric methods were applied for process optimization. (author)

Solvent extraction of Cu, Mo, V, and U from leach solutions of copper ore and flotation tailings.

Science.gov (United States)

Smolinski, Tomasz; Wawszczak, Danuta; Deptula, Andrzej; Lada, Wieslawa; Olczak, Tadeusz; Rogowski, Marcin; Pyszynska, Marta; Chmielewski, Andrzej Grzegorz

2017-01-01

Flotation tailings from copper production are deposits of copper and other valuable metals, such as Mo, V and U. New hydrometallurgical technologies are more economical and open up new possibilities for metal recovery. This work presents results of the study on the extraction of copper by mixed extractant consisting p -toluidine dissolved in toluene. The possibility of simultaneous liquid-liquid extraction of molybdenum and vanadium was examined. D2EHPA solutions was used as extractant, and recovery of individual elements compared for the representative samples of ore and copper flotation tailings. Radiometric methods were applied for process optimization.

Enrichment of Venezuelan graphitic ore through electrostatic separation and direct flotation

International Nuclear Information System (INIS)

Di Yorio, C.; Garcia-Carcedo, F.; Hernandez, A.; Ayala, N.; Cornejo, N.

1998-01-01

Graphite is an useful material in the modern industry. In Venezuela, other ores contain 8 to 14% of graphite from Cerro Osumita, Edo Cojedes, with enough reserves for exploitation. Samples from this deposit were characterized and tests of electrostatic and flotation were carried out. The electrical potential and velocity of drum were varied for two different size fractions. Kerosene, sodium silicate as depressant and pulp agitation were varied. The results indicate the important of size for the separation. Size below 0.5 mm is necessary. For good quality fixed carbon an electrical potential up to 15 kV and 0.02 g of kerosene is recommended. (Author) 8 refs

Optimization of flotation variables for the recovery of hematite particles from BHQ ore

Science.gov (United States)

Rath, Swagat S.; Sahoo, Hrushikesh; Das, B.

2013-07-01

The technology for beneficiation of banded iron ores containing low iron value is a challenging task due to increasing demand of quality iron ore in India. A flotation process has been developed to treat one such ore, namely banded hematite quartzite (BHQ) containing 41.8wt% Fe and 41.5wt% SiO2, by using oleic acid, methyl isobutyl carbinol (MIBC), and sodium silicate as the collector, frother, and dispersant, respectively. The relative effects of these variables have been evaluated in half-normal plots and Pareto charts using central composite rotatable design. A quadratic response model has been developed for both Fe grade and recovery and optimized within the experimental range. The optimum reagent dosages are found to be as follows: collector concentration of 243.58 g/t, dispersant concentration of 195.67 g/t, pH 8.69, and conditioning time of 4.8 min to achieve the maximum Fe grade of 64.25% with 67.33% recovery. The predictions of the model with regard to iron grade and recovery are in good agreement with the experimental results.

Effect of desliming on the flotation of a complax copper ore from China

OpenAIRE

Chen Yong; Song Yong Sheng; Li Wen Juan; Zhou Gui Ying

2016-01-01

The complex copper oxide ore sample was taken from Deerni copper deposit, Qinghai Province of China. Batch flotation tests had been conducted to upgrade the copper concentrate by conventional amyl xanthate reagents under 73% -74 μm of the particle size; however, the unsatisfied results (Cu grade of 18.21% and recovery of 59.25%) were obtained. Also there are a large amount of slimes trapped in the concentrate and high-dosages consumption of reagents, for example, more than 2.5 kg/t sodium sul...

New developments in flotation. Lectures

International Nuclear Information System (INIS)

Zuchowski, J.

1993-01-01

The following papers were presented at the meeting: sphalerite flotation XPS and calorimeter analyses; set-up of and first results from a column flotation pilot plant; alkenyl succinic acid semiester flotation collectors for apatite; laboratory- and pilot-scale apatite flotation by means of stirrer cells and pneumatic cells; a contribution to the use of a pneumatic flotation method for the treatment of oil-containing industrial waste water; technical development of the KEMCO processing plant, Thailand; computer-aided pneumatic flotation by example of a lead/zinc ore; combined flocculation/expansion flotation and electrofloation sewage treatment processes; deinking flotation -a comparison with mineral flotation; comparison of the new flotation cells: column cell, Jameson cell, pneumatic cell. (orig.) [de

Multidimensional Analysis of Copper Ore Flotation in Terms of Applied Hydrophobizing Agents

Science.gov (United States)

Pięta, Paulina; Niedoba, Tomasz; Surowiak, Agnieszka

2018-03-01

Flotation is a method of enrichment used to distribute particles, which differ in their surface properties. Hydrophobic solids intrinsically create contact at the solid-liquid-gas interface. However, not all minerals, including copper minerals, can be characterized by this crucial ability. In that case it is necessary to use the collector reagents which guarantees a high efficiency of the enrichment process. The main aim of the paper was to examine the impact of selected collector types and dosages on the results of Polish sandstone copper ore flotation and to find optimal parameter values for products that meet quality and quantity requirements. The laboratory tests were carried out with an application of two types of collectors (Hostaflot, sodium ethyl xanthate aqueous solution) in dosages 100 and 150 g/Mg. Data analysis was based on the use of the taxonomy methods in order to select optimal conditions of collector dosage and type. Based on the indexes, it was found that the best enrichment effects were obtained with a sodium ethyl xanthate aqueous solution 150 g/Mg.

Multidimensional Analysis of Copper Ore Flotation in Terms of Applied Hydrophobizing Agents

Directory of Open Access Journals (Sweden)

Pięta Paulina

2018-01-01

Full Text Available Flotation is a method of enrichment used to distribute particles, which differ in their surface properties. Hydrophobic solids intrinsically create contact at the solid-liquid-gas interface. However, not all minerals, including copper minerals, can be characterized by this crucial ability. In that case it is necessary to use the collector reagents which guarantees a high efficiency of the enrichment process. The main aim of the paper was to examine the impact of selected collector types and dosages on the results of Polish sandstone copper ore flotation and to find optimal parameter values for products that meet quality and quantity requirements. The laboratory tests were carried out with an application of two types of collectors (Hostaflot, sodium ethyl xanthate aqueous solution in dosages 100 and 150 g/Mg. Data analysis was based on the use of the taxonomy methods in order to select optimal conditions of collector dosage and type. Based on the indexes, it was found that the best enrichment effects were obtained with a sodium ethyl xanthate aqueous solution 150 g/Mg.

Surface chemistry of pyrite during the pre-processing for the flotation in alkaline sodium carbonate medium during uranium ore processing

International Nuclear Information System (INIS)

Neudert, A.; Sommer, H.; Schubert, H.

1991-01-01

It is often necessary during processing of uranium ore to flotate pyrite at sodium carbonate alkaline pH value caused by the subsequent hydrometallurgical process stages. It was found out by ESCA analyses that the pyrite surface changes chemically prior to the addition of flotation agents. FeS 2 becomes FeO within a few hours in the case of storage in process water; limonite and/or geothite result from pyrite. The copper ions of the activator CuSO 4 are exclusively monovalent on the pyrite surface. The resulting heavy metal xanthogenate is Cu(I) xanthogenate. Conclusions are derived for the flotation practice for the intensification of the reagent regime. (orig./HP) [de

The Desulfurization of Magnetite Ore by Flotation with a Mixture of Xanthate and Dixanthogen

Directory of Open Access Journals (Sweden)

Jun Yu

2016-07-01

Full Text Available The contamination of sulfur emanating from pyrrhotite in magnetite concentrates has been a problem in iron ore processing. This study utilized froth flotation to float pyrrhotite away from magnetite using collectors of xanthate and dixanthogen. It was found that xanthate or dixanthogen alone could not achieve selective separation between pyrrhotite and magnetite in flotation. A high loss of magnetite was obtained with xanthate, while a low desulfurization degree was obtained with dixanthogen. It was interesting that a high desulfurization ratio was achieved with little loss of magnetite when xanthate was mixed with dixanthogen as the collector. The synergistic effect of the mixed collector on pyrrhotite was studied by electrokinectic studies and FTIR measurements. It was found that xanthate was the anchor on pyrrhotite and determined its selectivity against magnetite, while dixanthogen associated with xanthate, enhancing its hydrophobicity. This study provides new insights into the separation of iron minerals.

On the mechanism of action of combination of thionocarbamates with xanthate during flotation of copper-molybdenum pyrite contained ores

International Nuclear Information System (INIS)

Nedosekina, T.V.; Glembotskij, A.V.; Bekhtle, G.A.; Novgorodova, Eh.Z.

1985-01-01

Investigation results of action mechanism of thionocarbamates combination with xanthate are described. It is established that these collectors are capable of co-adsorbing on pyrite surface, that is the reason for sharp increase of the floatability and disturbs the selectivity of copper-molybdenum pyrite-containing ore flotation

Control of clay minerals effect in flotation. A review

Directory of Open Access Journals (Sweden)

Taner Hasan Ali

2016-01-01

Full Text Available The increased exposure to low grade ores highlights the importance of understanding phyllosilicate gangue mineralogy which consists of common gangue minerals. To improve the flotation performance and ore quality the negative effect of the clay minerals on flotation should be identified. The presence of clay minerals leads to problems, such as changing the froth stability, which are related to swelling behaviour, increase in pulp viscosity, overconsumption of reagents, slime coating and mechanical entrainment. The clay content in the ore is changing from time to time and it is necessary to provide quick solutions to the issues caused by the new ore composition. The objective of this paper is to give an overview how to control the colloidal properties of clay minerals on flotation.

Recovery of primary cassiterite by flotation

International Nuclear Information System (INIS)

Oliveira, J.F. de; Penna, M.T.M.; Adamian, R.

1985-01-01

The flotation of cassiterite ores using samples of primary ore from Pela Ema, Brazil is studied. The cassiterite was characterized by X-ray fluorescence analysis. The samples were submitted to size reduction up ro minus loo m in order to obtain liberation of cassiterite in excess of 95%. The flotation tests were carried out without desliming. Several collectors and depressants were investigated, as well as the influence of the concentration of these reactants and the pH factor upon flotation of cassiterite. The results were analysed considering the flotability of the minerals, and the electrophoretic mobility of cassiterite, both in the presence and absence of selected collectors. (Author) [pt

Discovery of a Novel Cationic Surfactant: Tributyltetradecyl-Phosphonium Chloride for Iron Ore Flotation: From Prediction to Experimental Verification

Directory of Open Access Journals (Sweden)

Pan Chen

2017-12-01

Full Text Available In this work, tributyltetradecyl-phosphonium chloride (TTPC, has been first introduced to be a novel and efficient cationic surfactant for cationic reverse flotation separation of quartz from magnetite. The first-principles density functional theory calculations, Zeta potential measurements and adsorption isotherm measurements consistently predict that TTPC may be a promising collector that is better than dodecyl triethyl ammonium chloride (DTAC, based on the facts that TTPC and DTAC both prefer to physically adsorb on the quartz surface owing to electrostatic force, but the active part (P+(C4H93 of TTPC takes much more positive charges than that (N+(CH33 of DTAC. The micro-flotation and Bench-scale flotation results further verify that TTPC presents a stronger collecting power and much better selectivity for iron ore reverse flotation in comparison to the conventional collector DTAC. Furthermore, the corresponding adsorption mechanism of TTPC on the quartz have also been investigated in detail. This work might show a good example to discover a potential candidate collector by analogy with a known excellent collector based on reasonable prediction.

An investigation into the effects of various flotation parameters on the flotation behaviour of pyrite, gold and uranium contained in Witwatersrand type ores, and their practical exploitation

International Nuclear Information System (INIS)

Duchen, R.B.; Carter, L.A.E.

1986-01-01

The importance of copper sulphate, pH, conditioning time, grind, the intensity of agitation during conditioning, and the correct type of conditioning on the alkaline flotation of gold, uranium and pyrite from Witwatersrand type ores is shown. The peculiar 'run-away float' condition experienced at high pH with air agitated conditioning is presented. The best laboratory flotation results were obtained after 20 minutes of vigorous mechanical conditioning of the pulp at a pH of 11,8 with copper sulphate 100 g/t Aero promoter 3477 20 g/t, xanthate 80 g/t, frother 5 g/t, grind 68% in - 75 μm and pulp specific gravity of 1,280 (dry solids sp. gr. = 2,70). The practical implementation of the laboratory findings on the Hartebeestfontein No. 7 Shaft flotation plant resulted in an increase in gold recovery from about 76% to about 86%, and an increase in pyrite recovery from about 86% to about 92%

A study of bauxite tailing quality improvement by reverse flotation

Science.gov (United States)

Wulandari, W.; Purwasasmita, M.; Sanwani, E.; Malatsih, W.; Fadilla, F.

2018-01-01

The pre-treatment of bauxite ore from Tayan, West Kalimantan includes washing and screening fine bauxite particles (-2mm) prior as the feed to the Bayer process for producing alumina. These fine particles are believed to have high content of silica which is detrimental to the process. This washed bauxite tailing still has a significant amount of alumina content. Previous research has indicated that bauxite ore can be upgraded by applying reverse flotation method to reduce its silica content in the ore. Therefore, this study is aimed to utilize reverse flotation method to recover alumina content from washed bauxite tailing. The reverse flotation experiments were carried out at pH of 6 and 8; while the particle sizes were varied at - 140+270 mesh and -270 mesh, using a batch and circuit configuration. The result of this study shows that the batch reverse flotation can recover alumina in the tailing up to 81.4%, however the silica content is still significant. The complexity of silica-alumina minerals in the tailing prevents a complete separation of the ores by only using reverse flotation.

Multi-Stage Flotation for the Removal of Ash from Fine Graphite Using Mechanical and Centrifugal Forces

Directory of Open Access Journals (Sweden)

Xiangning Bu

2018-01-01

Full Text Available Graphite ore collected from Hunan province, south China was characterized by chemical analysis, X-ray diffraction, and optical microscopy. Rougher and multi-stage flotation tests using a mechanical flotation cell and a flotation column containing an additional centrifugal force field were carried out to promote its grade and economic value. In rougher flotation, both the mechanical flotation cell and flotation column reduced the ash content of the graphite ore from 15.43% to 10.8%, while the yield of the flotation column (91.41% was much higher than that of the mechanical flotation cell (50%. In the presence of hydrophobic graphite, the seriously entrained gangue restricted further improvement in the quality and economic value of the graphite ore. Therefore, multi-stage flotation circuits were employed to diminish this entrainment. Multi-stage flotation circuits using the two flotation devices further decreased the ash content of the graphite ore to ~8%, while the yield when using the flotation column was much higher than that obtained from the mechanical flotation cell employed. On the other hand, the ash removal efficiency of the flotation column was 3.82-fold higher than that observed for the mechanical flotation cell. The Cleaner 3 flotation circuit using the flotation column decreased the ash content in graphite from 15.43% to 7.97% with a yield of 77.53%.

Isolation and characterization of lost copper and molybdenum particles in the flotation tailings of Kennecott copper porphyry ores

Science.gov (United States)

Tserendavga, Tsend-Ayush

The importance of flotation separation has long been, and continues to be, an important technology for the mining industry, especially to metallurgical engineers. However, the flotation process is quite complex and expensive, in addition to being influenced by many variables. Understanding the variables affecting flotation efficiency and how valuable minerals are lost to the tailings gives metallurgists an advantage in their attempts to increase efficiency by designing operations to target the areas of greatest potential value. A successful, accurate evaluation of lost minerals in the tailings and appropriate solutions to improve flotation efficiency can save millions of dollars in the effective utilization of our mineral resources. In this dissertation research, an attempt has been made to understand the reasons for the loss of valuable mineral particles in the tailings from Kennecott Utah Copper ores. Possibilities include liberation, particle aggregation (slime coating) and surface chemistry issues associated with the flotation separation. This research generally consisted of three main aspects. The first part involved laboratory flotation experiments and factors, which affect the flotation efficiency. Results of flotation testing are reported that several factors such as mineral exposure/liberation and slime coating and surface oxidation strongly affect the flotation efficiency. The second part of this dissertation research was to develop a rapid scan dual energy (DE) methodology using 2D radiography to identify, isolate, and prepare lost sulfide mineral particles with the advantages of simple sample preparation, short analysis time, statistically reliable accuracy and confident identification. The third part of this dissertation research was concerned with detailed characterization of lost particles including such factors as liberation, slime coating, and surface chemistry characteristics using advanced analytical techniques and instruments. Based on the

Hydrodynamic aspects of flotation separation

Directory of Open Access Journals (Sweden)

Peleka Efrosyni N.

2016-01-01

Full Text Available Flotation separation is mainly used for removing particulates from aqueous dispersions. It is widely used for ore beneficiation and recovering valuable materials. This paper reviews the hydrodynamics of flotation separations and comments on selected recent publications. Units are distinguished as cells of ideal and non-ideal flow. A brief introduction to hydrodynamics is included to explain an original study of the hybrid flotation-microfiltration cell, effective for heavy metal ion removal.

Multi-Stage Flotation for the Removal of Ash from Fine Graphite Using Mechanical and Centrifugal Forces

OpenAIRE

Xiangning Bu; Tuantuan Zhang; Yaoli Peng; Guangyuan Xie; Erdong Wu

2018-01-01

Graphite ore collected from Hunan province, south China was characterized by chemical analysis, X-ray diffraction, and optical microscopy. Rougher and multi-stage flotation tests using a mechanical flotation cell and a flotation column containing an additional centrifugal force field were carried out to promote its grade and economic value. In rougher flotation, both the mechanical flotation cell and flotation column reduced the ash content of the graphite ore from 15.43% to 10.8%, while the ...

Technology of Polish copper ore beneficiation – perspectives from the past experience

Directory of Open Access Journals (Sweden)

Wieniewski Andrzej

2016-01-01

Full Text Available The paper describes the main types of existing copper deposits in the world and the most common enrichment technologies. The characteristic elements of the current flowsheet of the Polish ore beneficiation were discussed together with the reasons for using them. The paper presents a perspective flowsheet based on more than 50-years of experience in beneficiation of Polish copper ore. The main elements of proposed technology are: leaving in justified cases the division of ore into fractions of increased sandstone and carbonate ores content, flotation in the milling circuit as part of the effective preparation of the ore to rougher flotation, intensive rougher flotation, classic cleaning system, processing of the middlings with grinding system in new type mills, classification and flotation with outlet of final tailings.

Treatment of bastnaesite ore from Vietnamese Socialist Republic

International Nuclear Information System (INIS)

Formanek, J.; Jerabek, J.; Jancarek, J.

1987-01-01

From the Vietnamese deposit at Nam Nam Xe Czechoslovakia imported several hundred tons of ore. Several methods of ore dressing were used: gravitational, preconcentration in electromagnetic field, magnetic separation, high-intesity electromagnetic separation. Flotation evidently was the best dressing method tried. The results are presented of testing using different flotation agents. (E.S.)

Development of Technology for Enrichment of Silver Containing Ores

Science.gov (United States)

Shekiladze, Asmati; Kavtelashvili, Otari; Bagnashvili, Mamuka

2016-10-01

The progress of Georgian economics is substantially associated with a development of new deposits of mineral resources. Among them is the David-Gareji deposit where at present the intensive searching geological works are performed. The work goal involves the elaboration of the technology for processing of silver-containing quartz-barite ores. Without its development the mining of more valuable gold-polymetallic ores is impossible. Because of ore complexity silver and barite are considered in a common technological aspect. The investigations were carried out on the representative samples of quartz-barite ores containing 78-88 g/ton of silver and 27-29 % of silver is a nugget in the form of the simple sulphides and chlorides. The ore is characterized by fine coalescence of barite and ore-generating minerals. Non-ferrous metals haven't any industrial value because of their very low content. Therefore, for the processing of the ores under study the direct selective scheme of flotation enrichment was chosen and the formula of optimal reagent regime was elaborated. Potassium xanthogenate is used as a collector for flotation of silver minerals and pine oil- as a foaming agent. The effect of the pulp - pH and medium temperature on silver flotation was studied. It was established that the silver is actively floats in neutral medium. For barite flotation the various collectors were tested: sulfidezid cotton oil-soap stock, soaps of fatty acids and alkyl sulphates of C12 - C16 row, among the “Baritol” is the most efficient one. Depression of the barren rock was carried out by liquid glass in alkaline medium. The effect of pulp pH on barite flotation has been investigated. The best results were obtained at pH=8.5. The increase of the pulp alkalinity has no essential effect on the indexes of the barite enrichment. Conditional concentrate of the barite is obtained by two fold purification of the main flotation concentrate by the addition of the liquid glass to the re

The effects of mixtures of potassium amyl xanthate (PAX and isopropyl ethyl thionocarbamate (IPETC collectors on grade and recovery in the froth flotation of a nickel sulfide ore

Directory of Open Access Journals (Sweden)

Westhein Maree

2017-12-01

Full Text Available Potassium amyl xanthate (PAX and sodium isobutyl xanthate (SIBX are commonly used collectors in both the bulk and selective froth flotation of sulfide ores. These thiol xanthate collectors are conventionally mixed together as well as with more selective thiol collectors such as dithiophosphates (DTP and dithiocarbamates (DTC, in order to improve selectivity. With deteriorating nickel sulfide ores, more selective collectors and collector mixtures are desired for the efficient extraction of nickel. Thionocarbamates (TC are another group of thiol collectors used for selective froth flotation of sulfide minerals. Thionocarbamates are especially used in the selective froth flotation of chalcopyrite over pyrite and galena, but little is known about its selectivity with regards to nickel. Thionocarbamates are also more stable over larger pH ranges in comparison to xanthates and they possess beneficial frothing properties. This study compared the effects of using potassium amyl xanthate (PAX, isopropyl ethyl thionocarbamate (IPETC, sodium isobutyl xanthate (SIBX and their mixtures in the froth flotation of a pentlandite ore. In the mixtures of PAX or SIBX with IPETC, the xanthate accounted for 95.5 mol% and for the PAX and SIBX mixture a 50:50 mixture was used. This study showed that the highest cumulative nickel grades were obtained with PAX, SIBX and there mixture. The highest cumulative nickel recoveries were obtained with IPETC and its mixtures with PAX and SIBX (50–62%. Keywords: Nickel sulfide, Xanthate, Thionocarbamate, Grade, Recovery

A novel chemical scheme for flotation of rutile from eclogite tailing

Directory of Open Access Journals (Sweden)

Bo Xu

Full Text Available A novel chemical scheme for the flotation of rutile from eclogite tailings has been developed in this work. It consists of lead ion as the activator, sodium fluorosilicate (SF as the depressant, and styryl phosphonic acid (SPA and n-octyl alcohol (OCT as the collector. By using the proposed scheme to treat a feed ore of 4.5% TiO2, a rougher concentrate of grade 84.47% TiO2 was achieved with the recovery of 61.5%. Also, the scheme made a high flotation rate for rutile. The scheme was applied to closed-circuit flotation (one-stage rougher flotation, two-stage scavenger flotation and two-stage cleaner flotation, produced a concentrate of 92% TiO2 with the recovery of 70%. It is shown that the new chemical scheme would be a potential one for the effective separation of rutile from eclogite ores. Keywords: Rutile, Flotation, Reagents, Eclogite tailings

Tracer studies of flotation in laboratory and plant

International Nuclear Information System (INIS)

Niemi, A.J.; Thereska, J.; Plasari, E.; Kacaj, M.

1992-01-01

Froth flotation is used for the industrial extraction of valuable minerals from ores. Its progress depends on the properties of minerals being processed and on flotation practices. While flotation is basically a kinetic process, it functions industrially in continuous flow vessels whose flow patterns influence the separation effected. Radioisotope tracers have proven to be a necessary tool in the acquisition of both kinetic and flow pattern data

Comprehensive recovery of gold and base-metal sulfide minerals from a low-grade refractory ore

Science.gov (United States)

Li, Wen-juan; Liu, Shuang; Song, Yong-sheng; Wen, Jian-kang; Zhou, Gui-ying; Chen, Yong

2016-12-01

The comprehensive recovery of small amounts of valuable minerals such as gold and base-metal sulfide minerals from a low-grade refractory ore was investigated. The following treatment strategy was applied to a sample of this ore: gold flotation-gold concentrate leaching-lead and zinc flotation from the gold concentrate leaching residue. Closed-circuit trials of gold flotation yielded a gold concentrate that assayed at 40.23 g·t-1 Au with a recovery of 86.25%. The gold concentrate leaching rate was 98.76%. Two variants of lead-zinc flotation from the residue—preferential flotation of lead and zinc and bulk flotation of lead and zinc—were tested using the middling processing method. Foam from the reflotation was returned to the lead rougher flotation or lead-zinc bulk flotation, whereas middlings from reflotation were discarded. Sulfur concentrate was a byproduct. The combined strategy of flotation, leaching, and flotation is recommended for the treatment of this kind of ore.

Flotation process of lead-, copper-, uranium-, and rare earth minerals

International Nuclear Information System (INIS)

Broman, P.G.; Kihlstedt, P.G.; Du Rietz, C.

1977-01-01

This invention relates to a flotation process of oxide or sulfide ores containing lead-, copper-, uranium-, and rare earth minerals applicating a new collector. Flotation is in the presence of a tertiary amine

Economic evaluation of preconcentration of uranium ores

International Nuclear Information System (INIS)

1981-04-01

The economics of two options for the preconcentration of low-grade uranium ores prior to hydrochloric acid leaching were studied. The first option uses flotation followed by wet high-intensity magnetic separation. The second option omits the flotation step. In each case it was assumed that most of the pyrite in the ore would be recovered by froth flotation, dewatered, and roasted to produce sulphuric acid and a calcine suitable for acid leaching. Savings in operating costs from preconcentration are offset by the value of uranium losses. However, a capital saving of approximately 6 million dollars is indicated for each preconcentration option. As a result of the capital saving, preconcentration appears to be economically attractive when combined with hydrochloric acid leaching. There appears to be no economic advantage to preconcentration in combination with sulphuric acid leaching of the ore

Kaolinite removal from bauxite by flotation

Directory of Open Access Journals (Sweden)

Otávia Martins Silva Rodrigues

Full Text Available Abstract This paper presents a potential condition to separate kaolinite through flotation when it is present in bauxite ore. This research anticipates a Brazilian industry requirement, considering the tendency towards the need for aluminosilicates removal from bauxite ores, as has already occurred in China. Kaolinite is the most abundant aluminosilicate, and gibbsite is the main aluminum bearing mineral in Brazilian bauxite ores. The first step was a fundamental study involving microflotation experiments with pure samples of kaolinite and gibbsite. Ammonium quaternary salts and amines were used as the collector and corn starch as the depressant. In a fundamental study, the best conditions determined in the first step were evaluated for the flotation of kaolinite from bauxite ore using laboratory scale experiments. Tests with AQ142/starch (pH 10 and CTAB (pH 7 led to satisfactory results. In general, the highest values of alumina/silica mass ratio were obtained with AQ142/starch and the highest values of mass recovery and metallurgical recovery were achieved with CTAB.

Lar mountain phosphate ore processing using flotation approach

International Nuclear Information System (INIS)

Gharabaghi, M.; Noaparast, M.; Shafaei Tonkaboni, S. Z.

2007-01-01

The sample of Lar Mountain Phosphate deposit which is located in the southwest of Iran, was studied to upgrade its phosphate grade. The results obtained from mineralogical studies showed the presence of apatite, CaO, Al 2 O 3 , Fe 2 O 3 and SiO 2 , in which carbonate was detected as the main gangue. Two sets of direct and reverse flotation tests were performed using samples from this deposit with 10% P 2 O 5 . In phosphate flotation (direct approach), the samples were conditioned with sodium silica, oleic acid-fuel oil and Armac T-fuel oil. The direct flotation at pH=9.2 yielded a product with 23.2% of P 2 O 5 and 75.16% recovery. The reverse flotation tests were carried out at pH=5.2, with floating carbonate and pulp de-oiling, using H 2 SO 4 and wash water, and phosphate was then floated from siliceous gangue. In the second sets of the reverse approach, depressing the phosphate and floating silica with Amines in natural pH were done. However the best concentrate assay was 31.2% P 2 O 5 with a 71.12% recovery, which was obtained from reverse tests

The fines recovery of the phosphoro-uraniferous ores from Itataia-CE

International Nuclear Information System (INIS)

Furtado, J.R.V.

1985-01-01

Cyclone desliming previous to flotation is one of the determining factors of the concentration performance of phosfate ores. The physical beneficiation of the phosphoro uraniferous ore of Itataia, carried out in the pilot plant, rejects approximately 10,5% P 2 O 5 and 14% U 3 O 8 contained as ''slimes''. The present investigation was to develop a process to recover the fines through the tecniques of flotation and Seletive Floculation. The low P 2 O 5 content and extremely small size of the ''slimes'', led to a low efficiency in the operation of either flotation. The introduction of a Second disliming step swhed promising results. It is work mentioning that the ore presents siliceous-carbonatic gangue and that the direct flotation of phosphates rejects only the silicate portion. Direct flotation followed by reverse flotation of carbonates led to phosphate concentrates containing 28% P 2 O 5 with recoveries of 60%. The results obtained indicate that the fines treatment may lead to increase of 4,5% in overall recovery without decreasing the grade of the final concentrate. (C.D.G.) [pt

PGAA method for control of the technologically important elements at processing of sulfide ores

International Nuclear Information System (INIS)

Kurbanov, B.I.; Aripov, G.A.; Allamuratova, G.; Umaraliev, M.

2006-01-01

Full text: Many precious elements (Au, Re, Pt, Pd, Ag, Cu, Ni, Co, Mo) in ores mainly exist in the form of sulfide minerals and the flotation method is often used for processing of such kind of ores. To enhance the efficiency of the process it is very important to carry out the operative control of the elements of interest at various stages of ore processing. In this work the results of studies for developing methods for control of technologically important elements at processing and enrichment sulfide ores, which content the gold, copper, nickel, molybdenum in the ore-processing plants of Uzbekistan. The design of transportable experimental PGAA device on the basis of low-power radionuclide neutron source ( 252 Cf) with neutrons of 2x10 7 neutr/sec allowing to determine element content of the above named ores and their processing products is offered. It is shown that the use of the thermal neutron capture gamma-ray spectrometry in real samples and technological products allows prompt determination of such elements as S, Cu, Ti and others, which are important for flotation of sulfide ores. Efficiency control of the flotation processing of sulfide ores is based on quick determination of the content of sulfur and some other important elements at different stages of the process. It was found that to determine elements the following gamma lines are the most suitable - 840.3 keV for sulfur, 609 keV and 7307 keV for copper and 1381.5 keV, 1498.3 keV and 1585.3 keV for titanium. Based on the measurements of original ores, concentrates of various stages of flotation and flotation slime the possibility for prompt determination of S, Cu and Ti content and thus to get necessary information on the efficiency of the flotation process was shown. (author)

The performance of leaching and bio-leaching from sulphide ores usiing SEVOP

OpenAIRE

Krstev, Boris; Krstev, Aleksandar; Golomeov, Blagoj; Golomeova, Mirjana; Sala, Ferat; Gocev, Zivko; Zivanovic, Jordan; Krstev, Dejan

2013-01-01

The refractory or low grade copper chalcopyrite ores or galena/sphalerite domestic ores in Republic of Macedonia are investigated by conventional copper flotation and selective flotation for galena/sphalerite. In the meantime, investigations are directed to the new possibilities of leaching by microorganisms – bioleaching. The paper is result of these technologies and investigations carried out for recovery of in the mentioned ores. Using Simplex EVOP and computer programme. Multisimple...

Characterization and Separation Studies of a Fine Sedimentary Phosphate Ore Slime

Directory of Open Access Journals (Sweden)

Xin Liu

2017-06-01

Full Text Available Detailed characterization and recovery of apatite from a sedimentary phosphate ore slime of a gravity plant of Yichang, China, were investigated. The phosphate ore slime consisted mainly of apatite, quartz, dolomite, and clay. To start with, the ore slime was characterized in sufficient detail to reveal that it is extremely fine in distribution with a d50 of 65 μm. Other different characterizations, such as apatite grain size distribution, apatite liberation, particle density distribution, and theoretical grade recovery, were also analyzed by mineral liberation analyser (MLA. Based on the results, a new gravity-flotation process, which was comprised of spiral gravity and reverse flotation, was proposed to process the slime. In the new process, the apatite was firstly recovered by two-stage spiral gravity, avoiding direct flotation. The gravity concentrate was the feed for the reverse flotation. A phosphate concentrate of 30.51% P2O5 with a P2O5 recovery of 89.00% can be produced from the slime analyzing 24.25% P2O5. Compared to the conventional direct-reverse flotation process, it was found that the reagent cost of the new gravity-flotation process was lower a quarter than that of the direct-reverse flotation flowsheet.

Flotation separation of waste plastics for recycling-A review.

Science.gov (United States)

Wang, Chong-qing; Wang, Hui; Fu, Jian-gang; Liu, You-nian

2015-07-01

The sharp increase of plastic wastes results in great social and environmental pressures, and recycling, as an effective way currently available to reduce the negative impacts of plastic wastes, represents one of the most dynamic areas in the plastics industry today. Froth flotation is a promising method to solve the key problem of recycling process, namely separation of plastic mixtures. This review surveys recent literature on plastics flotation, focusing on specific features compared to ores flotation, strategies, methods and principles, flotation equipments, and current challenges. In terms of separation methods, plastics flotation is divided into gamma flotation, adsorption of reagents, surface modification and physical regulation. Copyright © 2015 Elsevier Ltd. All rights reserved.

Molybdenum extraction from copper-molybdenum ores

International Nuclear Information System (INIS)

Nevaeva, L.M.

1982-01-01

Molybdenum extraction from copper-molybdenum ores as practised in different countries is reviewed. In world practice the production process including depression of copper and iron sulfides and flotation of molybdenite is widely spread. At two USA factories the process of a selective flotation with molybdenite depression by dextrin is used

Creating value through application of flotation science and technology

Energy Technology Data Exchange (ETDEWEB)

Clark, M.E.; Brake, I.; Huls, B.J.; Smith, B.E.; Yu, M. [BHP Billiton, Melbourne, Vic. (Australia)

2006-05-15

A brief outline of some of the pioneering events in the development of flotation technology, which originated in Broken Hill at the start of the 1900s, is presented. The development of the original Potter-Delprat process, the introduction of oils to generate froth flotation and the achievement of selective flotation processing are described, all focussed on solving challenges with the Broken Hill Pb-Ag-Zn ores. Some recent initiatives in flotation at BHP Billiton operations are also outlined, covering coal, copper, lead-silver-zinc and diamonds. Some views are offered on the characteristics of innovation in flotation and on possible trends into the future.

Evaluation of flotation process course on the example of sulphide ores

Directory of Open Access Journals (Sweden)

Oleksik Konrad

2017-01-01

Full Text Available The article concerns investigations over the influence of selected parameters of the flotation process course on the values of technological indices of beneficiation process assessment. Following parameters were under evaluation: the pulp density, pulp aeration (measured through the rotational speed of rotor as well as dosage of flotation reagents. Four technological indices were registered: concentrate recovery, concentrate grade, yield of the concentrate and the tails grade. There were calculated correlation coefficients between selected parameters of flotation process course and the values of technological indices, along with determination of significance of these coefficient, at accepted probability level 0.95. In the next stage of investigations there were determined mathematical models with the concentrate recovery, concentrate grade, yield of concentrate and tails grade as the functions of pulp density, speed of the rotor and dosage of flotation reagent. On the basis of the investigations carried out, it was appeared that the dosage of flotation reagent was of the most significant influence on the values of technological indices of flotation process assessment. The least significant influence, in turn, was obtained for the pulp density.

Molecular design of flotation collectors: A recent progress.

Science.gov (United States)

Liu, Guangyi; Yang, Xianglin; Zhong, Hong

2017-08-01

The nature of froth flotation is to selectively hydrophobize valuable minerals by collector adsorption so that the hydrophobized mineral particles can attach air bubbles. In recent years, the increasing commercial production of refractory complex ores has been urgent to develop special collectors for enhancing flotation separation efficiency of valuable minerals from these ores. Molecular design methods offer an effective way for understanding the structure-property relationship of flotation collectors and developing new ones. The conditional stability constant (CSC), molecular mechanics (MM), quantitative structure-activity relationship (QSAR), and first-principle theory, especially density functional theory (DFT), have been adopted to build the criteria for designing flotation collectors. Azole-thiones, guanidines, acyl thioureas and thionocarbamates, amide-hydroxamates, and double minerophilic-group surfactants such as Gemini, dithiourea and dithionocarbamate molecules have been recently developed as high-performance collectors. To design hydrophobic groups, the hydrophilic-hydrophobic balance parameters have been extensively used as criteria. The replacement of aryl group with aliphatic group or CC single bond(s) with CC double bond(s), reduction of carbon numbers, introduction of oxygen atom(s) and addition of trisiloxane to the tail terminal have been proved to be useful approaches for adjusting the surface activity of collectors. The role of molecular design of collectors in practical flotation applications was also summarized. Based on the critical review, some comments and prospects for further research on molecular design of flotation collectors were also presented in the paper. Copyright © 2017 Elsevier B.V. All rights reserved.

Recovery of molybdenum in froth flotation

International Nuclear Information System (INIS)

Parlman, R.M.; Bresson, C.R.

1981-01-01

Beta-mercaptoethanol has been found to be an effective suppressant for such minerals as copper, iron and lead in a molybdenum sulfide ore froth flotation operation. The recovery process and a suppressant utilizing said compound are claimed

Applicability of attrition of iron ore in floating

International Nuclear Information System (INIS)

Fortes, Fabiana Fonseca

2010-01-01

The aim of this study is to investigate the possibility to increase metal recovery in the flotation of iron ore with the implementation of a stage of scrubbing followed by dispersion. The minerals in question stems from two mines located in the western portion of the Iron Quadrangle and differ mainly with respect to the percentage of hematite and porous and the presence of aggregated masses. These characteristics were compared to those of other minerals that have succeeded with the adoption of this technique. Tests were conducted at bench scale scrubbing, desliming and concentration by flotation with the blend of ore from both mines. Were varied stirring time and pH. The chemical results of desliming and flotation products in the different conditions were compared. The presence of porous hematite is relevant in a mine, mainly due to the occurrence of earthy goethite, alumina carrier of the contaminant. The step desliming is insufficient for the removal of harmful sludge flotation. Laboratory experiments showed that the scrubbing of the pulp of iron ore of Minas de Capitao do Mato and Tamandua, agitated for 10 minutes followed by desliming amid scattered, promotes increased metal recovery by about 17% and increases the selectivity of 40 % compared to the results of the scrubbing and without dispersion. The scrubbing of hematite ore followed by desliming amid scattered can bring gains in improving the quality of pellet feed fine if deployed industrially. (author)

Uranium accompanying recovery from copper ores

International Nuclear Information System (INIS)

Golynko, Z.Sh.; Laskorin, B.N.

1981-01-01

In the search for new raw material sources for nuclear power engineering a review of the technique of uranium accompaning recovery from copper ores reprocessing products in some countries is presented. In the USA a sorption method of uranium extraction by means of strongly basic ion exchange resins from solutions upon copper case- hardening with subsequent extraction from eluates by solutions of tertiary amines is realized. Elution is realized with sulphuric acid. In South Africa an extraction reprocessing of gravitational concentrate extracted from copper sulphide flotation tailings is organized. In India the uranium extraction from copper ores flotation enrichment tailings is organized on a commerical scale. Presented are data on the scale of uranium recovery, various conditions of its recovery as well as block diagrams of the processes. It is shown that copper ores become an additional source of uranium recovery [ru

Study in pilot plant of the Itataia phosphoro-uraniferous ore - CE (Brazil)

International Nuclear Information System (INIS)

Reis Junior, J.B.; Aquino, J.A. de; Oliveira Luz, I.L. de.

1987-01-01

Pilot plant data have been obtained for the physical treatment studies of the Itataia, phosphoro-uraniferous ore body located in the state of Ceara-Brazil. Due to the presence of the silic-carbonated gangue, which turns the ore complex, the pilot plant operation comprised 1200 hours. From the results obtained, it was possible to stablish a basic flowsheet for the concentration process. Such process includes a grinding step followed by a cyclone disliming (d 50 =10μm). The cyclone underflow feeds the flotation step. The conventional flotation process, which envolves the direct phosphate flotation followed by cleaning steps, was not efficient due to the presence of the carbonated gangue. In fact, the presence of silicates and carbonates in the gangue required that the flotation would be carried out in two steps. The silicated gangue is eliminated in the first flotation and a phosphate concentrate with significant amount of carbonates is obtained. This concentrate is fed to the second flotation step, termed reverse flotation, where the calcite is floated and the apatite is depressed. (Author) [pt

Study in pilot plant of the Itataia phosphoro-uraniferous ore (CE,Brazil)

International Nuclear Information System (INIS)

Reis Junior, J.B.; Aquino, J.A. de; Oliveira Luz, I.L. de

1985-01-01

Pilot plant data have been obtained for the physical treatment studies of the Itataia, phosphoro-uraniferous ore body located in the state of Ceara-Brazil. Due to the presence of the silic-carbonated gangue, which turns the ore complex, the pilot plant operation comprised 1200 hours. From the results obtained, it was possible to establish a basic flowsheet for the concentration process. Such process includes a grinding step (-65) followed by a cyclone disliming (d50 = 10μ). The cyclone underflow feeds the flotation step. The conventional flotation process, which envolves the direct phosphate flotation followed by cleaning steps, was not efficient due to the presence of the carbonated gangue. In fact, the presence of silicates and carbonates in the gangue required that the flotation would be carried out in two steps. The silicated gangue is eliminated in the first flotation and a phosphate concentrate with significant amount of carbonates is obtained. This concentrate is fed to the second flotation step, termed reverse flotation, where the calcite is floated and the apatite is depressed. (Author) [pt

Recovery of kaolinite from tailings of Zonouz kaolin-washing plant by flotation-flocculation method

OpenAIRE

Kianoush Barani; Masoud Kalantari

2018-01-01

The traditional processing of kaolin is achieved by dispersion of the mined ore and classification by multistage hydrocyclone plants. The inefficiencies inherent to cyclones produce a middling product that is commonly disposed back into the quarry. In this research, recovery of kaolinite from tailings of Zonouz kaolin washing plant, which is located in Iran was investigated by flotation and flotation- flocculation. Flotation experiments show that the flotation of kaolinite from the tailings i...

A review of zinc oxide mineral beneficiation using flotation method.

Science.gov (United States)

Ejtemaei, Majid; Gharabaghi, Mahdi; Irannajad, Mehdi

2014-04-01

In recent years, extraction of zinc from low-grade mining tailings of oxidized zinc has been a matter of discussion. This is a material which can be processed by flotation and acid-leaching methods. Owing to the similarities in the physicochemical and surface chemistry of the constituent minerals, separation of zinc oxide minerals from their gangues by flotation is an extremely complex process. It appears that selective leaching is a promising method for the beneficiation of this type of ore. However, with the high consumption of leaching acid, the treatment of low-grade oxidized zinc ores by hydrometallurgical methods is expensive and complex. Hence, it is best to pre-concentrate low-grade oxidized zinc by flotation and then to employ hydrometallurgical methods. This paper presents a critical review on the zinc oxide mineral flotation technique. In this paper, the various flotation methods of zinc oxide minerals which have been proposed in the literature have been detailed with the aim of identifying the important factors involved in the flotation process. The various aspects of recovery of zinc from these minerals are also dealt with here. The literature indicates that the collector type, sulfidizing agent, pH regulator, depressants and dispersants types, temperature, solid pulp concentration, and desliming are important parameters in the process. The range and optimum values of these parameters, as also the adsorption mechanism, together with the resultant flotation of the zinc oxide minerals reported in the literature are summarized and highlighted in the paper. This review presents a comprehensive scientific guide to the effectiveness of flotation strategy. Copyright © 2013 Elsevier B.V. All rights reserved.

Evaluation of the properties of complexing agent-collectors of eudialyte flotation

Directory of Open Access Journals (Sweden)

Mitrofanova G.V.

2015-06-01

Full Text Available Acid-based and complexing properties of reagent-collectors (carboxylic and hydroxamic acids, styrylphosphonic acid and dialkyl ether of phosphoric acid for flotation of zirconium-containing minerals have been studied. Stability constants for zirconium compounds of investigated reagents have been determined. Eudialyte-containing ore flotation has proved high efficiency of hydroxamic acids

A Review on New Technological Progress for Beneficiation of Refractory Phosphate Ore in China

Science.gov (United States)

Dong, Xu; Siqing, Liu; Yanqing, Yao; Hailin, Liu; Yi, Pei

2017-05-01

The world is rich in phosphate resources, but the vast majority of the resources are of middle and low grade ores, and it is difficult to obtain high grade concentrate at a high recovery by using traditional separation methods. In this paper, the distribution and flotation processes of typical phosphate ores in China are introduced. Considering the current situation in phosphate ore beneficiation both home and abroad, the new trend of processing technology and reagents in China are summarized. Flotation is still regarded as the main processing method in phosphate ore beneficiation for a certain time in near future.

Flotation of kaolinite from tailings of kaolin-washing plants by cationic collectors

OpenAIRE

Barani Kianoush

2016-01-01

Traditional processing of kaolin is achieved by dispersion of the mined ore and classification by means of multistage hydrocyclones. The inefficiencies inherent to cyclones produce a middling product that is commonly disposed back to the quarry. In this research recovery of kaolinite from tailings of the Zonoupz kaolin washing plant, which is located in Iran, was investigated by cationic flotation. Flotation experiments showed that flotation of kaolinite from tailings was much better in an ac...

Hemimorphite Ores: A Review of Processing Technologies for Zinc Extraction

Science.gov (United States)

Chen, Ailiang; Li, Mengchun; Qian, Zhen; Ma, Yutian; Che, Jianyong; Ma, Yalin

2016-10-01

With the gradual depletion of zinc sulfide ores, exploration of zinc oxide ores is becoming more and more important. Hemimorphite is a major zinc oxide ore, attracting much attention in the field of zinc metallurgy although it is not the major zinc mineral. This paper presents a critical review of the treatment for extraction of zinc with emphasis on flotation, pyrometallurgical and hydrometallurgical methods based on the properties of hemimorphite. The three-dimensional framework structure of hemimorphite with complex linkage of its structural units lead to difficult desilicification before extracting zinc in the many metallurgical technologies. It is found that the flotation method is generally effective in enriching zinc minerals from hemimorphite ores into a high-grade concentrate for recovery of zinc. Pure zinc can be produced from hemimorphite or/and willemite with a reducing reagent, like methane or carbon. Leaching reagents, such as acid and alkali, can break the complex structure of hemimorphite to release zinc in the leached solution without generation of silica gel in the hydrometallurgical process. For optimal zinc extraction, combing flotation with pyrometallurgical or hydrometallurgical methods may be required.

Steady-state optimization of ore-dressing plants

International Nuclear Information System (INIS)

Niemi, A.J.

1989-01-01

The ore-dressing plant consists of the steps of grinding and flotation. Its optimization is based on steady state simulation of the mass balances with a plant model. The model data are obtained by tracer tests and analysis. An evaluation of performance of the plant has to observe the recovery of the valuable mineral, the throughput of the system and the grade of the concentrate which are outputs of the flotation plant. Simulation with the flotation plant model yields that combination of values of controllable inputs to flotation which corresponds to an optimal operation of the conditioning an flotation system, for a specified feed and its fractional composition. Simulations for other feeds and compositions advise how they should be chosen, for a better overall performance. (author)

Application of X-ray luminescence separation to preliminary enrichment of lean scheelite-containing ores

International Nuclear Information System (INIS)

Zhaboev, M.N.; Semochkin, G.A.; Blinov, Yu.I.; Dzhambaev, F.M.; Novikov, V.V.; Tereshchenko, S.V.

1987-01-01

Investigations of preliminary enrichment of lean ores of amphibole hornfels by the method of X-ray luminescence separation was conducted. Pile and enriched products with different WO 3 content were obtained from these ores; WO 3 content in pile products was 2-2.5 times lower as compared to factory tailing products. WO 3 content in separator concentrate corresponds in all cases to the requirements for the ore designated for flotation enrichment. Carbonate modulus decreases 2.5-4 times in separation concentrate, simplifying the conditions of flotation

The flotation of rare earths - a contribution to industrial hygiene

International Nuclear Information System (INIS)

Andrews, W.H.; Collins, D.N.; Hollick, C.T.

1990-01-01

Conventional processing of heavy mineral deposits containing radioactive rare earth minerals such as monazite and xenotime may cause industrial hygiene problems through atmospheric dust and contamination of product concentrates. An alternative procedure has been developed by Wimmera Industrial Mineral Pty. Ltd. at the Drung South deposit in Victoria. The radioactive minerals are removed from bulk heavy mineral concentrates by flotation with little loss of other economic minerals. With fine ores, recoveries of over 95% have been achieved and with coarse ores over 80%. The potential for generation of radioactive dust or product contamination in subsequent processing is correspondingly reduced. Several flotation regimes, which have proven effective are discussed. 7 refs., 7 tabs., 1 fig

Functional activity of microorganisms in mining and processing of copper-nickel ores in the Murmansk Region

Directory of Open Access Journals (Sweden)

Fokina N. V.

2018-03-01

Full Text Available The quantitative indices and structure of the microbial community in flotation samples of sulfide copper-nickel ores at concentration plant of Kola Mining and Metallurgical Company have been determined. The smallest number of saprotrophic and oligotrophic bacteria has been observed in samples of ore and recycled water, which can be explained by the low temperature of samples and the lack of nutrients. It has been found out that the bacteria contained in the ore and recycling water flowing from the tailings increased their number during the flotation process due to coming of the organic compounds with the flotation reagents, aeration and increased temperature. Dominating strains have been isolated from recycled water and basic flotation products and classified as Pseudomonas. It has been shown that with an increase in the number of bacteria, the flotation time of copper-nickel ores increases. There is also a tendency to change the extraction of copper and nickel, which can be caused by both the increase in the flotation time for operations and the change in the number of bacteria in the circulating water. The thionic bacteria have been distinguished from the flow tailings of the Allarechensk deposit. The heap leaching experiments have proved the bacterial leaching to give good results on the ore samples passed through magnetic separation, having shown high content of the nickel and copper in filters. When leaching low-grade ore of the Nude Terrasa, the advantage of bacterial leaching use in comparison with the sulphuric-acid leaching only to copper has been revealed. The nickel content in the filtrates for bacterial leaching is 275 mg/l, and for sulfuric acid – 310 mg/l. The average copper content in the filtrates is 19 and 15 mg/l.

Synthesis and flotation activity of reagent-collectors based on dithiocarbonyl and phosphoryl derivatives of amino alcohols

Directory of Open Access Journals (Sweden)

Nazgul Orazbaevna Akimbaeva

2017-09-01

Full Text Available Research has been carried out to study the flotation activity of new surface active substances among dithiocarbonyl and phosphoryl derivatives of monoethanolamine and diethanolamine on the gold-bearing sulphide ore of the Bestobinskoye deposit of Kazakhstan. Among the first synthesized compounds, effective collectors for selective enrichment of sulfide polymetallic gold ores were found. Sodium N-octyl-N-2-hydroxyethyldithiocarbamate (AA-41 and sodium O-2-(dimethoxyphosphoryl-2-hydroxyethylaminoethylxanthate (GF-2 were proposed as new flotation reagents. They were tested in the flotation of gold-bearing polymetallic ore as additional collectors and showed good results, contributing to an increase in the percentage of gold extraction in the collective concentrate in comparison with the factory basic regime in which a mixture of butyl xanthate (BX and ditiophosphate butyl ether or butyl airoflot (BAF was used. The results of flotation tests indicate that the collective ability of AA-41 flotation agent as an additional collector is at the level of BX. While the GF-2 flotation agent as a collector in combination with BAF provides a higher gold recovery to the concentrate of 90.8%, which is higher than gold recovery when combined with BX and BAF collectors (87.7%. It should be specially emphasized that the consumption of collectors AA-41 and GF-2 in comparison with the BX consumption in the base mode is much lower, so the AA-41 consumption is 11% lower and the consumption of GF-2 is lower by 33%. Methods for synthesizing the AA-41 flotation reagents and GF-2 flotation agents were developed, and the evidence of their structure was given with the help of physicochemical methods (IRS and NMR 1Н, 13С. The principal technological scheme of the process of obtaining the flotation agent-collector GF-2, which showed the best results in the flotation of gold-bearing polymetallic ore, was developed. In the synthesis of the flotation reagent AA-41, one of the

Selective Flotation of Calcite from Fluorite: A Novel Reagent Schedule

Directory of Open Access Journals (Sweden)

Zhiyong Gao

2016-10-01

Full Text Available Fluorite is an important strategic mineral. In general, fluorite ores will contain a certain amount of calcite gangue mineral. Thus, they need to be separated from each other. For an economic separation, a reverse flotation process is used to float calcite gangue from fluorite. However, little information on the separation is available. In this study, a novel reagent schedule using citric acid (CA as the depressant, sodium fluoride (NaF as the regulator and sulfoleic acid (SOA as the collector, was developed to separate calcite from fluorite. The results demonstrated a high selectivity for the flotation of calcite from fluorite using this new reagent schedule. The best selective separation for a single mineral and mixed binary minerals was obtained when 200 mg/L of NaF, 50 mg/L of CA, and 6 mg/L of SOA were used at pH 9. In addition, a batch flotation experiment was carried out using a run-of-mine feed material. Selective separation was achieved with 85.18% calcite removal while only 11.2% of fluorite was lost. An attempt was made to understand the effect of the new reagent schedule on the flotation of calcite. The results from both microflotation and bench scale flotation demonstrated a great potential for industrial application using this novel reagent schedule to upgrade fluorite ore.

Beneficiation studies of Bajaur manganese ore by different processing techniques

International Nuclear Information System (INIS)

Riaz, M.; Khan, F.U.; Yamin, A.; Bilquees, R.; Muhammad, N.

2010-01-01

The manganese ore of Bajaur Agency of Pakistan was subjected to flotation, heavy medium separation, gravity concentration and magnetic separation techniques for beneficiation. The original composition of the manganese ore was 45.56% Mn , 4% Fe/sub 2/O/sub 3/, 40% SiO/sub 2/. The Mn content was raised to a maximum 48.76 % in the concentrate with the recovery of 67.78 % through flotation technique. Other techniques rendered marginal increase in Mn concentration against the theoretical possibility of substantial enrichment by rejecting the 20 % gangue minerals. The separation of manganese minerals from associated gangue was difficult, due to mineralogical complexity of the ore, extreme fineness of the particle size, texture and minerals intergrowth. High Mn/Fe ratio, phosphorus, and silica contents were within tolerable limits for utilisation of the ore in ferro-manganese production. (author)

Characterization and dewatering of flotation technological tailings

Directory of Open Access Journals (Sweden)

Grigorova I.

2014-01-01

Full Text Available The treatment of flotation tailings is today a subject of interest in mineral processing because of the potential of wasted materials as an actual mineral resource and because of environmental reasons. Decantation ponds are found at almost every mine in the world. They are large earth fill dams containing the residue of the milling process to extract metals from mined ores. Traditional wet tailings disposal has been problematic due to the risk of ground water contamination and the difficulty in rehabilitating storage sites. Tailings dams are at risk of failure due to leakage, instability, liquefaction, and poor design. In the last few years the use of paste technology in the disposal of mine tailings is increasingly studied as an option to conventional tailings dams. The Lucky Invest Concentrator is located in the Eastern Rhodopes Mountain of Bulgaria. Since 1959 lead-zinc ores are dressed. Finally, during the flotation cycle lead and zinc concentrates are produced. The final technological processing waste precipitates in tailing pond. Research and development program has started to established opportunities to obtain dry deposit of the ore processing residue and analyses the feature of new tailing disposal method. The tailings particle size distributions and chemical compositions were determined. The data from laboratory and pilot scale tests clearly illustrate that there are the possibilities to obtaine lead-zinc dewatered tailings. The experimental results show that new cyclone modifications have a potential in dewatering technology of flotation tailings. It appears that dewatering cyclones can be an approach on new tailings pond elimination technology.

Thiosulphate leaching of gold-, silver-, copper flotation concentrates

International Nuclear Information System (INIS)

Samikhov, Sh.R.; Zinchenko, Z.A.

2015-01-01

Present article is devoted to thiosulphate leaching of gold-, silver-, copper flotation concentrates. For the purpose to improve the process of thiosulphate leaching the ore samples were calcined at temperature 600 ℃ during two hours. During the calcination process of gold-sulphide ores and concentrates the minerals pyrite and arsenopyrite oxidize which lead to opening of gold contains in them. It was defined that thiosulphate leaching can be recommended as an alternative to cyanic process.

Conditioning in the flotation of gold, uranium oxide, and pyrite

International Nuclear Information System (INIS)

Stassen, F.J.N.

1991-01-01

The effect of conditioning energy on the flotation of gold, U 3 O 8 , and pyrite was investigated in the range 0,1 to 100 kWh per tonne of dry ore for various combinations of conditioning time and impeller speed in a cylindrical conditioning tank. It was found that, when the conditioning energy was increased to between 5 and 10 kWh per tonne of dry ore, the total recovery and flotation rate of the valuable minerals (expressed as Klimpel parameters) increased substantially. The Klimpel parameters are dependent on conditioning energy, but are independent of conditioning time or impeller speed (at constant conditioning energy). The Klimpel parameters of the gangue are independent of conditioning energy. 23 refs., 7 tabs., 2 figs

Developments in gold and silver recovery through flotation in processing of gold ore slags; Avances en la recuperacion de oro y plata mediante flotacion en escorias de procesamiento de menas de oro

Energy Technology Data Exchange (ETDEWEB)

Hidalgo, N.; Diaz, A.; Bazan, V.; Sarquis, P.

2015-07-01

The aim of this work is to recover and improve the extraction of gold and silver present in smelting slags through various mineralogical processes applicable in gold ores. The slag was concentrated in a Knelson type centrifuge, two concentrates (C1 and C2 and a tailing T1) being obtained. In order to improve the recovery, three series of rougher flotation tests were conducted on the tailing T1. The variables analyzed were: particle size, type of collectors (xanthates, di-monothiophosphate) and flotation time. It was deduced that by applying gravity concentration, the recovery of Au and Ag (Knelson centrifuge) is 42.0% and 13.7%, respectively. Au recovery is improved by 87.7% through the flotation of the centrifuge separation tailings, whereas that for Ag is 47.4%. The optimum conditions were: particle size 200 mesh, collectors: PAX (15.8 g/t), F-C5439 (18.75 g/t), MIBC frother (12.5g/t) and 8.5 minutes of flotation time. (Author)

Flotation of kaolinite from tailings of kaolin-washing plants by cationic collectors

Directory of Open Access Journals (Sweden)

Barani Kianoush

2016-01-01

Full Text Available Traditional processing of kaolin is achieved by dispersion of the mined ore and classification by means of multistage hydrocyclones. The inefficiencies inherent to cyclones produce a middling product that is commonly disposed back to the quarry. In this research recovery of kaolinite from tailings of the Zonoupz kaolin washing plant, which is located in Iran, was investigated by cationic flotation. Flotation experiments showed that flotation of kaolinite from tailings was much better in an acidic than in an alkaline medium containing cationic collectors.

Water leaching of titanium from ore flotation residue.

Science.gov (United States)

Jaworska, Malgorzata M; Guibal, Eric

2003-01-01

Copper ore tailings were tested for the stability of titanium submitted to water leaching in three different reactor systems (agitated vessel, bioreactor and percolated fixed-bed column). For each of these systems, titanium extraction did not exceed 1% of the available metal. Biomass removed from ore residue adsorbed a small part of the titanium with sorption capacities below 20-30 mg g(-1), but most of this biomass was sequestered in the ore residue. Oxygen and carbon dioxide concentrations were monitored and changes in concentration correlated with bacteria development at the initial stage of the process and to fungal development in the latter stages.

X-ray fluorescence separation of pure lead-zinc ores

International Nuclear Information System (INIS)

Lapshin, S.A.; Filippov, O.K.; Khachatryan, L.S.; Rudnev, B.P.

1987-01-01

To evaluate the influence of the previous concentration of polymetallic ores by the radiometric separation method on indices of flotation and gravitation enrichments, investigations were carried out using ore sample (1.94%Pb, 1.13% Zn) from a lead-zink ore deposit. It is shown that the results obtained on the enrichment of the ore and products of X-ray radiometric separation are similar. However previous removal (up to 40%) of dead rock permits to reduce sharply grinding and transpot costs

The effect of fine presence in flotation of phosphate from Itataia-Brazil

International Nuclear Information System (INIS)

Dantas, J.O.C.; Adamian, R.

1987-01-01

Some important aspects in the flotation of phosphorus-uraniferous ore from Itataia, Brazil, are presented. The effect of particle size and problems caused by the presence of calcite in the gangue which engages the selectivity of the process are studied. The mineral characterization, grinding tests and flotation tests were done. The Kinetic parameters: maximum extrapolated recovery and kinetic constant were calculated. (M.C.K.) [pt

Integrated Approaches for the Study of Real Mineral Flotation Systems

Directory of Open Access Journals (Sweden)

Andrea Gerson

2013-01-01

Full Text Available It is more common than not, for mineral processing studies to proceed via the examination of model flotation systems with the resulting data often lacking statistical verification. The resultant concentrates and tails may then be subjected to a restricted range of analyses, for diagnosis of the flotation behavior variations observed, that themselves bias the outcomes. For instance surface analysis may be undertaken without reference to solution speciation, or liberation may be studied but surface speciation may not be taken into account. We propose an integrated approach whereby firstly the flotation data are vigorously scrutinized and the mineralogy, liberation, surface and solution speciation are examined in parallel to establish a chemical over view of the system. It is proposed that to make progress in the understanding of flotation systems, in terms of the minerals chemistry, that a multi-dimensional analytical approach is utilized and that the focus shifts towards the analysis of real ores and industrial flotation systems.

The effect of lizardite surface characteristics on pyrite flotation

International Nuclear Information System (INIS)

Feng Bo; Feng Qiming; Lu Yiping

2012-01-01

Highlights: ► Two kinds of lizardite samples have different effect on the flotation of pyrite. ► Acid leaching changed the surface characteristics of lizardite mineral. ► The leached lizardite has less magnesium on its surface. ► The electro-kinetic behavior of lizardite aqueous suspensions is mainly a function of the Mg/Si atomic ratio on mineral surface. - Abstract: The effect of lizardite surface characteristics on pyrite flotation has been investigated through flotation tests, adsorption tests, zeta potential measurements, FTIR study, X-ray photoelectron spectroscopy (XPS) and sedimentation tests. The flotation results show that at pH value 9, where flotation of nickel sulfide ores is routinely performed, two kinds of lizardite samples (native lizardite and leached lizardite) have different effects on the flotation of pyrite. The native lizardite adheres to the surface of pyrite and reduces pyrite flotation recovery while the leached lizardite does not interfere with pyrite flotation. Infrared analyses and XPS tests illustrate that acid leaching changed the surface characteristics of lizardite mineral and the leached lizardite has less magnesium on its surface. It has been determined that the electro-kinetic behavior of lizardite aqueous suspensions is mainly a function of the Mg/Si atomic ratio on lizardite surface. So, the low isoelectric point observed in the leached sample has been linked to values of this ratio lower than that of the native lizardite.

Beneficiation of Venezuelan graphitic ore through electrostatic separation and direct flotation; Enriquecimiento de menas grafiticas venezolanas mediante separacion electrostatica y flotacion directa

Energy Technology Data Exchange (ETDEWEB)

di Yorio, C [Universidad de Venezuela (Venezuela); Garcia-Carcedo, F; Hernandez, A; Ayala, N; Cornejo, N [Centro Nacional de Investigaciones Metalurgicas. CENIM. Madrid (Spain)

1998-12-01

Graphite is an useful materials in the modern industry. In venezuela, other ore contains 8 to 14% of graphite from Cerro Osumita, Edo Cojedes, with enough reserves for exploitation. Samples from this deposit were characterized and tests of electrostatic and flotation were carried out. The electrical potential and velocity of drum were varied for two different size fractions. Kerosene, sodium silicate as depressant and pulp agitation were varied. The results indicate the important of size for the separation. Size below 0.5 mm is necessary. For good quality fixed carbon an electrical potential up to 15 kV and 0.02 g of kerosene is recommended. (Author) 8 refs.

Concentration of gold, sulphide minerals and uranium oxide minerals by flotation from ores and metallurgical plant products

International Nuclear Information System (INIS)

Weston, D.

1974-01-01

A process for the recovery by froth flotation of gold and mineral values selected from the group consisting of gold bearing minerals, platinum group minerals, silver group minerals, and uranium group minerals, from ores and metallurgical plant products containing at least gold and at least one of the other said minerals comprising: subjecting a suitably prepared pulp of the material to mechanical agitation in at least one agitation conditioning stage wherein the pH of the said pulp has been lowered with an acid agent to an optimum pH point within the pH range of about 1.5 to 5.0 and wherein the agitation conditioning is for a sufficient period of time to bring about heavy activation of at least one of the said mineral values in at least one subsequent mechanical agitation conditioning stage wherein the said pulp is further agitation conditioned for a sufficient period of time and at an optimum pH point in the pH range of about 6.0 to 11.0 in the presence of at least one collector selected from the group of sulfhydryl anionic collectors to produce the said heavy activation of at least gold and at least one of the other said mineral values; and subsequently in the presence of a frother subjecting and said agitation conditioned pulp to flotation to produce a concentrate enriched in gold and at least one of the othersaid mineral values, and a tailings product impoverished in at least gold and at least one of the other said mineral values

Optimization of chemical composition in the manufacturing process of flotation balls based on intelligent soft sensing

Directory of Open Access Journals (Sweden)

Dučić Nedeljko

2016-01-01

Full Text Available This paper presents an application of computational intelligence in modeling and optimization of parameters of two related production processes - ore flotation and production of balls for ore flotation. It is proposed that desired chemical composition of flotation balls (Mn=0.69%; Cr=2.247%; C=3.79%; Si=0.5%, which ensures minimum wear rate (0.47 g/kg during copper milling is determined by combining artificial neural network (ANN and genetic algorithm (GA. Based on the results provided by neuro-genetic combination, a second neural network was derived as an ‘intelligent soft sensor’ in the process of white cast iron production. The proposed ANN 12-16-12-4 model demonstrated favourable prediction capacity, and can be recommended as a ‘intelligent soft sensor’ in the alloying process intended for obtaining favourable chemical composition of white cast iron for production of flotation balls. In the development of intelligent soft sensor data from the two real production processes was used. [Projekat Ministarstva nauke Republike Srbije, br. TR35037 i br. TR35015

Magmatic ore deposits in layered intrusions - Descriptive model for reef-type PGE and contact-type Cu-Ni-PGE deposits

Science.gov (United States)

Zientek, Michael L.

2012-01-01

Layered, ultramafic to mafic intrusions are uncommon in the geologic record, but host magmatic ore deposits containing most of the world's economic concentrations of platinum-group elements (PGE) (figs. 1 and 2). These deposits are mined primarily for their platinum, palladium, and rhodium contents (table 1). Magmatic ore deposits are derived from accumulations of crystals of metallic oxides, or immiscible sulfide, or oxide liquids that formed during the cooling and crystallization of magma, typically with mafic to ultramafic compositions. "PGE reefs" are stratabound PGE-enriched lode mineralization in mafic to ultramafic layered intrusions. The term "reef" is derived from Australian and South African literature for this style of mineralization and used to refer to (1) the rock layer that is mineralized and has distinctive texture or mineralogy (Naldrett, 2004), or (2) the PGE-enriched sulfide mineralization that occurs within the rock layer. For example, Viljoen (1999) broadly defined the Merensky Reef as "a mineralized zone within or closely associated with an unconformity surface in the ultramafic cumulate at the base of the Merensky Cyclic Unit." In this report, we will use the term PGE reef to refer to the PGE-enriched mineralization, not the host rock layer. Within a layered igneous intrusion, reef-type mineralization is laterally persistent along strike, extending for the length of the intrusion, typically tens to hundreds of kilometers. However, the mineralized interval is thin, generally centimeters to meters thick, relative to the stratigraphic thickness of layers in an intrusion that vary from hundreds to thousands of meters. PGE-enriched sulfide mineralization is also found near the contacts or margins of layered mafic to ultramafic intrusions (Iljina and Lee, 2005). This contact-type mineralization consists of disseminated to massive concentrations of iron-copper-nickel-PGE-enriched sulfide mineral concentrations in zones that can be tens to hundreds

Floatability study of graphite ore from southeast Sulawesi (Indonesia)

Science.gov (United States)

Florena, Fenfen Fenda; Syarifuddin, Fahmi; Hanam, Eko Sulistio; Trisko, Nici; Kustiyanto, Eko; Enilisiana, Rianto, Anton; Arinton, Ghenadi

2016-02-01

Graphite ore obtained from Kolaka Regency, South East Sulawesi, Indonesia have been succesfully investigated for beneficiation by froth flotation technique. Preliminary study have been done to determine the minerals types, fixed carbon content and liberation size of the graphite. Graphite is naturally floatable due to its hydrophobic property. Some suitable reagents are usually added to increase effectiveness of recovery. In this article, enrichment of graphite by froth flotation was studied by investigating the effect of reagents concentrations, rotation speed and particle size on the carbon grade and recovery of the concentrate. The carbon grade increased from 3.00% to 60.00% at the optimum flotation conditions.

Beneficiation studies on low-grade complex polymetallic lead-zinc ore of duddar (lasbela) Balochistan, Pakistan

International Nuclear Information System (INIS)

Bhatti, M.R.; Kazim, K.R.; Mehmood, R.; Akram, A.

2016-01-01

A bench-scale beneficiation study was performed on low-grade complex lead-zinc ore of Duddar area, District Lasbela, Balochistan Province, Pakistan. The polymetallic ore under investigation contains galena and sphalerite as valuable minerals of lead and zinc. The low-grade ore was upgraded by selective sequential froth flotation technology to recover both minerals. An effort was made to investigate the effect of important variables on grade and recovery of concentrates and to design the process flow sheet. Different parameters of flotation process such as particle size of the feed, pH and % solids of the pulp, speed of impeller, type of reagents (collectors, frothers, regulators and modifiers) and their quantities, conditioning time and flotation time were optimized to attain maximum grade and recovery of respective concentrates. The rougher concentrates obtained were subjected to one regrinding and two cleaning operations to achieve higher-grade concentrates of both metals. Bench-scale flotation tests show that it is possible to obtain a lead concentrate assaying 65.24% Pb with recovery rate of 81.32% and a zinc concentrate containing 55.63% Zn content with recovery rate of 80.28%. Both the concentrates meet the specifications required for metallurgical and chemical grades. (author)

Effect of dissolution kinetics on flotation response of calcite with oleate

Directory of Open Access Journals (Sweden)

D. G. Horta

Full Text Available Abstract Phosphate flotation performance can be influenced by the dissolution kinetics of the minerals that compose the ore. The purpose of this work was to investigate the effect of dissolution kinetics on flotation response with oleate (collector of calcites from different origins and genesis. The calcite samples were first purified and characterized by x-ray Fluorescence (XRF and the Rietveld method applied to x-ray Diffractometry data (RXD. Experiments of calcite dissolution and microflotationwere performed at pH 8 and pH 10.The pH effect on the calcite dissolution and flotation indicates the possible influence of the carbonate/bicarbonate ions provided by the CO2 present in the air. In addition, the flotation response is greater as the dissolution increases, making more Ca2+ ions available to interact with collector molecules. This result corroborates the surface precipitation mechanism proposed foroleate adsorption on the calcite surface.

Flotation of uranium values using di (2-ethyl hexyl) phosphoric acid

International Nuclear Information System (INIS)

Singh, Ajoy Kumar; Padmanabhan, N.P.H.; Sridhar, U.; Krishna Rao, N.

1998-01-01

The use of solvent extractants for mineral flotation, especially for difficult-to-float minerals, is gaining importance as they are highly selective to specific metal ions and form strong and stable complexes mostly by chelation. Studies carried out with di(2 ethyl hexyl) phosphoric acid (D2EHPA) (an organic solvent used in the extraction of uranium from phosphoric acid) as collector for flotation of uranium minerals from ore samples of Domiasiat, Meghalaya and Jaduguda, Bihar have yielded encouraging results. Although flotation of uranium minerals using other solvent extractants like tributyl phosphoric acid (TBP) has been studied, the uraninite-D2EHPA system has not been tested so far. This technical note puts on record the findings of the preliminary studies carried out. (author)

Influence of some ions on the flotation of apatite from Itataia, in Brazil

International Nuclear Information System (INIS)

Aquino, J.A. de.

1987-01-01

The influence of ionic composition in the water from Itataia dam in flotation process for phosphate recovery contained in the ore from Itataia reserve CE, in Brazil, is studied. A water treatment system to assure levels of content and recovery obtained during ore dressing stage is defined. Laboratory tests to verify variation of P 2 O 5 recovery in function of different ion concentration were done. (M.C.K.) [pt

Depressing effect of phenoxyl acetic acids on flotation of minerals containing Ca2+/Mg2+ gangues

Institute of Scientific and Technical Information of China (English)

无

2007-01-01

Phenoxyl acetic acids were applied to determine their depressing effect on minerals containing Ca2+/Mg2+ gangues. Calcite,mixture of calcite and fluorite, and nickel ore were used in the flotation. And the depression mechanism was studied by the determination of contact angle, zeta potential, adsorptive capacity of collector, and IR analysis as well. It is found that 0.1 mmol/L of phenoxyl acetic acid derived from pyrogallol or gallic acid exhibits strong depressing ability on calcite in almost zero yields at pH value of 9.8, and calcite can be depressed in the flotation of calcite/fluorite mixture for approximate 87% yield of fluorite. The flotation result of practical nickel ore containing serpentine indicates that these two depressants may also show better depression performance to serpentine than traditional depressants such as sodium fluosilicate and carboxylmethyl cellulose. Analysis for the depression mechanism reveals that there exists strong chemical interaction between the depressants and minerals.

Applicability of attrition of iron ore in floating; Aplicabilidade da atricao do minerio de ferro na flotacao

Energy Technology Data Exchange (ETDEWEB)

Fortes, Fabiana Fonseca

2010-07-01

The aim of this study is to investigate the possibility to increase metal recovery in the flotation of iron ore with the implementation of a stage of scrubbing followed by dispersion. The minerals in question stems from two mines located in the western portion of the Iron Quadrangle and differ mainly with respect to the percentage of hematite and porous and the presence of aggregated masses. These characteristics were compared to those of other minerals that have succeeded with the adoption of this technique. Tests were conducted at bench scale scrubbing, desliming and concentration by flotation with the blend of ore from both mines. Were varied stirring time and pH. The chemical results of desliming and flotation products in the different conditions were compared. The presence of porous hematite is relevant in a mine, mainly due to the occurrence of earthy goethite, alumina carrier of the contaminant. The step desliming is insufficient for the removal of harmful sludge flotation. Laboratory experiments showed that the scrubbing of the pulp of iron ore of Minas de Capitao do Mato and Tamandua, agitated for 10 minutes followed by desliming amid scattered, promotes increased metal recovery by about 17% and increases the selectivity of 40 % compared to the results of the scrubbing and without dispersion. The scrubbing of hematite ore followed by desliming amid scattered can bring gains in improving the quality of pellet feed fine if deployed industrially. (author)

Recovery of kaolinite from tailings of Zonouz kaolin-washing plant by flotation-flocculation method

Directory of Open Access Journals (Sweden)

Kianoush Barani

2018-04-01

Full Text Available The traditional processing of kaolin is achieved by dispersion of the mined ore and classification by multistage hydrocyclone plants. The inefficiencies inherent to cyclones produce a middling product that is commonly disposed back into the quarry. In this research, recovery of kaolinite from tailings of Zonouz kaolin washing plant, which is located in Iran was investigated by flotation and flotation- flocculation. Flotation experiments show that the flotation of kaolinite from the tailings is better in an acidic than in an alkaline medium containing cationic collectors. Flotation under acidic condition causes problems such as equipment corrosion at industrial scale. As a result, the cationic flotation of kaolinite is enhanced by addition of polyacrylamide as a flocculant. The results showed flocculation by polyacrylamide improved flotation of kaolinite within a range of pH. With 300 g/t dodecylamine, 500 g/t aluminum chloride, 50 g/t pine oil (frother, 15 g/t polyacrylamide, at pH = 7 and without de-slimming a product has 37.19% Al2O3, 54.19% SiO2 and 34.43% mass recovery was archived. Keywords: Kaolinite, Flotation, Flocculation, Cetylpyridinium chloride, Dodecylamine, Aluminum chloride, Polyacrylamide

Uranium Processing Research in Australia [Processing of Low-Grade Uranium Ores

Energy Technology Data Exchange (ETDEWEB)

Stewart, J R [Australian Atomic Energy Commission, Coogee, N.S.W. (Australia)

1967-06-15

Uranium processing research in Australia has included studies of flotation, magnetic separation, gravity separation, heavy medium separation, atmospheric leaching, multi-stage leaching, alkali leaching, solar heating of leach pulps, jigged-bed resin-in-pulp and solvent-in-pulp extraction. Brief details of the results obtained are given. In general, it can be said that gravity, magnetic and flotation methods are of limited usefulness in the treatment of Australian uranium ores. Alkali leaching seldom gives satisfactory recoveries and multi-stage leaching is expensive. Jigged-bed resin-in-pulp and packed tower solvent-in-pulp extraction systems both show promise, but plant-scale development work is required. Bacterial leaching may be useful in the case of certain low-grade ores. The main difficulties to be overcome, either singly or in combination, in the case of Australian uranium ores not currently considered economically exploitable, are the extremely finely divided state of the uranium mineral, the refractory nature of the uranium mineral and adverse effects due to the gangue minerals present. With respect to known low-grade ores, it would be possible in only a few cases to achieve satisfactory recovery of uranium at reasonable cost by standard treatment methods. (author)

Influence of particle size on the recovery of galene in electro flotation

International Nuclear Information System (INIS)

Ntampaka, B.

1987-01-01

The difficulties to recovery very small particles by conventional flotation need the development of all methods likely to give the best results. And this owing to the actual tendency which consists in including in the stocks of valorized ores, those with mineral particles finely scattered needing a very advanced grinding. Among these methods (va cum flotation, ionic flotation, column flotation, etc...), the electro flotation, which uses the electrolysis of pulp for it's airing seems to have a great interest but in fortunately its still on a laboratory scale. The passage to the industrial scale needs the putting in a conspicuous position of all possibilities of the method. However the studies have shown that the method should particularly be effective in recovering of several minerals finely ground. In this article, we have confirmed the fact in the case of galene. We have furthermore showed that the rate of recuperation increases with the decreasing of the size of the particles. The recovering is maximal for the particles under μm. This phenomen is different from the one observed in conventional flotation. We have given the reasons of this difference in this article.

Separation Mechanism of Fatty Acids from Waste Cooking Oil and Its Flotation Performance in Iron Ore Desiliconization

Directory of Open Access Journals (Sweden)

Wenda Guo

2017-12-01

Full Text Available Using the mixed fatty acids (MFA produced by waste cooking oil as flotation collectors directly, the flotation effect is usually not satisfactory, especially at lower temperature, which may be due to the presence of large amounts of saturated fatty acids. In this study, waste cooking oil was separated into saturated fatty acids (SFA and unsaturated fatty acids (UFA. The separation mechanism was studied by molecular simulation based on quantum and molecular mechanics. SFA and UFA were analyzed by iodine value, melting point measurement and Fourier transform infrared (FT-IR spectroscopy to check the result of the separation. The micro-flotation and bench-scale flotation tests were performed to investigate the flotation differences between SFA and UFA. The results showed that the poor flotation performance of waste cooking oil was due to the large amount of SFA in presence. If the SFA was separated out, the TFe grade and recovery of the flotation concentrates would be increased by 4.09 and 2.70 percentage points, respectively and the SiO2 grade would be 4.03 percentage points lower at the same time. This study would provide technical supports and theoretical guidance for the waste cooking oil application in the field of mineral processing.

Preliminary study on collectorless flotation of chalcocite, bornite and copper-bearing shale in the presence of selected frothers

Directory of Open Access Journals (Sweden)

Drzymala Jan

2016-01-01

Full Text Available Flotation of carbonaceous copper-bearing shale and copper sulfide minerals such as chalcocite and bornite in the presence of only frother was investigated. It was determined that all investigated solids did not float in pure water in the absence of flotation reagents. However, an addition of a frother rendered both shale and bornite floatable, while the recovery of chalcocite was negligible. These findings suggest that removal of carbonaceous matter from the ore by the so-called pre-flotation process can be a suitable procedure to reduce the amount of organic carbon in the concentrates provided that the feed does not contain bornite. Otherwise, simple pre-flotation must be replaced with a more sophisticated process in which flotation of bornite is suppressed.

Concentration of rare earths ore from Pocos de Caldas - MG, Brazil

International Nuclear Information System (INIS)

Sampaio, J.A.; Lins, F.F.; Porphirio, N.H.

1990-01-01

The objective of this research was to concentrate, mainly by flotation, a rare-earth ore body. The valuable mineral is bastnaesite which occurs intimately associated with iron oxides and other gangue minerals, making difficult to get a concentrate of commercial grade. The use of oleic acid at a pulp temperature of -80 sup(0)C gave a concentrate of 23% rare-earth oxides at 72% overall recovery. The magnetic separation could enhance the grade of the flotation feed. (author)

Development and functioning of microorganisms in concentration cycles of sulfide copper-nickel and non-sulfide apatite-nepheline ores

Directory of Open Access Journals (Sweden)

Fokina N. V.

2017-03-01

Full Text Available The number and trophic diversity of bacteria in flotation samples of apatite-nepheline and sulfide copper-nickel ores at the concentration plants of JSC "Apatite" and Kola Mining and Metallurgical Company have been determined. The study of the size and diversity of the microbiota has been conducted by culture on selective nutrient media. The total number and biomass of bacteria have been considered by fluorescence microscopy using Cyclopore polycarbonate membrane filters. Bacteria have been identified by molecular genetic methods. The least amount of both saprotrophic and other trophic groups of bacteria has been observed in the samples of ore and recycled water as at the concentrating factory of Apatit JSC, and also at the plant "Pechenganikel". It has been found out that the bacteria contained in the ore and recycling water flowing from the tailings increased their number during the flotation process due to coming of the nutrients with the flotation reagents, aeration and increased temperature. Strains which occurrence is more than 60 % have been extracted from recycled water and basic flotation products and classified as Pseudomonas. Two strains with occurrence of more than 60 % have been discovered at Apatit JSC and classified as Stenotrophomonas and Acinetobacter. The number of fungi in the cycle of apatite-nepheline ore enrichment at the factories is very low (1 to 24 CFU / 1 ml or 1 g of ore. Fungi of the genus Penicillium have been dominated, fungi of the genera Acremonium, Aureobasidium, Alternaria, Chaetomium have also been detected. At the plant "Pechenganikel" species Aspergillus fumigatus, Penicillium aurantiogriseum and P. glabrum have been extracted. It has been shown that the bacteria deteriorate the apatite flotation as a result of their interaction with active centers of calcium-containing minerals and intensive flocculation decreasing the floatation selectivity. Also some trend of copper and nickel recovery change has been

Flotation of uranium from uranium ores in Canada. Part 2

International Nuclear Information System (INIS)

Muthuswami, S.V.; Vijayan, S.; Woods, D.R.

1985-01-01

Measurements are reported for the equilibrium of cupferron from solutions by uranium oxide, quartz, illite, a mixture of these three, pitchblende, pyrite and brannerite ore. The cupferron concentration ranged from 1 to 6 g/L, and the pH was 7 and 8. Most isotherms followed the Langmuir model, although Freundlich behaviour was observed for illite and pitchblende. Most adsorption was pH independent except for illite and pitchblende. The adsorption isotherms for a mixture of uranium oxide, quartz and illite in the same proportions as in the naturally occurring ore agreed with the adsorption of the pyrite-free ore at pH 8 but not pH 7. We attribute the discrepancy to the use of illite as the model clay. The specific adsorption of cupferron on quartz and illite is lower by a factor of about 50 and 5, respectively, than the adsorption on uranium oxide. Specific adsorption less than 1 mg cupferron per gm of pyrite free ore does not float the mineral. The corresponding equilibrium concentration of cupferron is 0.5 g/L. A qualitative model is given, and the implications of this work for practical operations are presented

Simulation of a high-pressure water jet structure as an innovative tool for pulverizing copper ore in KGHM Polska Miedź S.A.

Directory of Open Access Journals (Sweden)

Przemysław Józef Borkowski

2016-01-01

Full Text Available Effective comminution of copper ore for further processing during flotation is still a challenge, both as a technological problem as well as for the high energy costs of such processing.A high-pressure water jet is one alternative method of preparing copper ore for final flotation, causing distinct enlargement of the surface of micronized particles, which could be profitable for copper production.As a consequence of such innovative processing, particles of copper ore become micronized, ensuring grain fractions directly useful for flotation at the exit of the pulverizing apparatus (the hydro-jetting mill.The paper presents some results of simulation as well as describing an analysis of the phenomena occurring inside the high-pressure water and abrasive-water jets of specific structures, elaborated in the aspect of developing hybrid jets of maximum erosive efficiency, potentially useful for effective pulverization.

Flotation in column-recovery of fine uranium phosphate ore from Itataia, in Brazil

International Nuclear Information System (INIS)

Reis Junior, J.B.; Peres, A.E.C.

1987-01-01

A systematic study of main variables of the flotation column and, the study of different pillot circuits integrated by flotation cells in colunm and mechanic cells, aiming at reduction the loss of the sludges for processing uranium phosphate from Itataia, in Brazil, are presented. A recovery of 49% of P 2 O 5 for a content of 24% of P 2 O 5 and 0,185% of U 3 O 8 in the concentrate, using a circuit with two columns, a rougher and scavenger, was obtained. For a content of 33.4% of P 2 O 5 and 0.240% of U 3 O 8 , a recovery of 38% of P 2 O 5 was obtained, using a circuit composed by a mechanical cell as scavenger and two columns as rougher and cleaner. The circuit used to obtain these parameters operated with 7,6 Kg/h solid flow in the grain size range of 10μm and 3μm and the flotation column with 5 cm of diameter and 6m of high. (M.C.K.) [pt

Investigation of column flotation process on sulphide ore using 2-electrode capacitance sensor: The effect of air flow rate and solid percentage

Science.gov (United States)

Haryono, Didied; Harjanto, Sri; Wijaya, Rifky; Oediyani, Soesaptri; Nugraha, Harisma; Huda, Mahfudz Al; Taruno, Warsito Purwo

2018-04-01

Investigation of column flotation process on sulphide ore using 2-electrode capacitance sensor is presented in this paper. The effect of air flow rate and solid percentage on column flotation process has been experimentally investigated. The purpose of this paper is to understand the capacitance signal characteristic affected by the air flow rate and the solid percentage which can be used to determine the metallurgical performance. Experiments were performed using a laboratory column flotation cell which has a diameter of 5 cm and the total height of 140 cm. The sintered ceramic sparger and wash water were installed at the bottom and above of the column. Two-electrode concave type capacitance sensor was also installed at a distance of 50 cm from the sparger. The sensor was attached to the outer wall of the column, connected to data acquisition system, manufactured by CTECH Labs Edwar Technology and personal computer for further data processing. Feed consisting ZnS and SiO2 with the ratio of 3:2 was mixed with some reagents to make 1 litre of slurry. The slurry was fed into the aerated column at 100 cm above the sparger with a constant rate and the capacitance signals were captured during the process. In this paper, 7.5 and 10% of solid and 2-4 L/min of air flow rate with 0.5 L/min intervals were used as independent variables. The results show that the capacitance signal characteristics between the 7.5 and 10% of solid are different at any given air flow rate in which the 10% solid produced signals higher than those of 7.5%. Metallurgical performance and capacitance signal exhibit a good correlation.

The Effect of Seaweed Glue in the Separation of Copper–Molybdenum Sulphide Ore by Flotation

Directory of Open Access Journals (Sweden)

Zhixiang Chen

2018-01-01

Full Text Available Flotation separation of chalcopyrite from molybdenite was studied using seaweed glue (SEG as a depressant. Flotation process and mechanism were examined by response surface methodology, flotation tests, adsorption tests, zeta potential measurements and fourier transform infrared (FT-IR spectra. Response surface methodology with a Box–Behnken design suggested the optimal reagent schedule: pH 4, depressant seaweed glue 197 mg/L, collector amyl xanthate 16 mg/L and frother (methyl isobutyl carbinol 20 mg/L, and selective separation of chalcopyrite and molybdenite was achieved by flotation. Comparison of SEG and traditional depressants indicated that the SEG could achieve a similar separation efficiency, and exhibited the advantages of environmental compatibility and economic adaptability. Co-adsorption of seaweed glue and amyl xanthate occurred on the surface of molybdenite, and is explained to happen through distinct mechanisms due to the heterogeneous nature of the surface. It is likely that seaweed glue depresses molybdenite by covering the dixanthogen resulting from adsorption of xanthate ions. It is shown that seaweed glue is as effective a depressant of Cu/Mo separation as cyanide.

Chemical and colloidal aspects of collectorless flotation behavior of sulfide and non-sulfide minerals.

Science.gov (United States)

Aghazadeh, Sajjad; Mousavinezhad, Seyed Kamal; Gharabaghi, Mahdi

2015-11-01

Flotation has been widely used for separation of valuable minerals from gangues based on their surface characterizations and differences in hydrophobicity on mineral surfaces. As hydrophobicity of minerals widely differs from each other, their separation by flotation will become easier. Collectors are chemical materials which are supposed to make selectively valuable minerals hydrophobic. In addition, there are some minerals which based on their surface and structural features are intrinsically hydrophobic. However, their hydrophobicities are not strong enough to be floatable in the flotation cell without collectors such as sulfide minerals, coal, stibnite, and so forth. To float these minerals in a flotation cell, their hydrophobicity should be increased in specific conditions. Various parameters including pH, Eh, size distribution, mill types, mineral types, ore characterization, and type of reaction in flotation cells affect the hydrophobicity of minerals. Surface analysis results show that when sulfide minerals experience specific flotation conditions, the reactions on the surface of these minerals increase the amount of sulfur on the surface. These phenomenons improve the hydrophobicity of these minerals due to strong hydrophobic feature of sulfurs. Collectorless flotation reduces chemical material consumption amount, increases flotation selectivity (grade increases), and affects the equipment quantities; however, it can also have negative effects. Some minerals with poor surface floatability can be increased by adding some ions to the flotation system. Depressing undesirable minerals in flotation is another application of collectorless flotation.

Coal-oil assisted flotation for the gold recovery

Energy Technology Data Exchange (ETDEWEB)

Sen, S.; Seyrankaya, A.; Cilingir, Y. [Dokuz Eylul University, Izmir (Turkey). Mining Engineering Department

2005-09-01

Using coal-oil agglomeration method for free or native gold recovery has been a research subject for many researchers over the years. In this study, a new approach 'coal-oil assisted gold flotation' was used to recover gold particles. The coal-oil-gold agglomeration process considers the preferential wetting of coal and gold particles. The method takes advantage of the greater hydrophobicity and oleophilicity of coal and gold compared to that the most gangue materials. Unlike the previous studies about coal-oil-gold agglomeration, this method uses a very small amount of coal and agglomerating agents. Some experiments were conducted on synthetic gold ore samples to reveal the reaction of the coal-oil assisted gold flotation process against the size and the number of gold particles in the feed. It was observed that there is no significant difference in process gold recoveries for feeds assaying different Au. Although there was a slight decrease for coarse gold particles, the process seems to be effective for the recovery of gold grains as coarse as 300 {mu} m. The decrease in the finest size ({lt} 53 {mu} m) is considered to be the decrease in the collision efficiency between the agglomerates and the finest gold particles. The effect of changing coal quantity for constant ore and oil amounts was also investigated. The experiments showed that the process gives very similar results for both artificial and natural ore samples; the best results have been obtained by using 30/1 coal-oil ratio.

Mining, ore preparation and niobium alloys production at Araxa, Brazil

International Nuclear Information System (INIS)

Paraiso, O.S.; Fuccio Junior, R. de; Betz, E.W.

1984-01-01

A detailed description of the worlds major niobium producer is presented covering mining, concentration by froth flotation, leaching, and production of ferro-alloys. The present exploration of the Araxa deposit, its ore preparation and production of ferro-niobium is described. (E.G.) [pt

Optimization of copper ore concentration processing by means of radioactive tracers

International Nuclear Information System (INIS)

Petryka, L.; Przewlocki, K.

1989-01-01

Flotation of polymetallic ores in the Polish Lower Silesian Basin was taken as an example for the optimization of copper ore processing using radioactive tracers. An original stochastic mathematical model (stream model) was proposed to minimize copper losses in tailing. A detailed procedure of measurement is presented as well as the experimental data and their interpretation. On the basis of this research copper losses in tailing can be reduced to one third. (author)

The recovery of a concentrate of tin and tungsten from ore mined at Van Roois Vley

International Nuclear Information System (INIS)

Guest, R.N.

1985-01-01

Concentration tests using gravity separation, flotation, and magnetic separation showed that it is possible for the high-grade ore mined at Van Roois Vley to be upgraded to a concentrate containing 61 per cent Sn-Wo 3 at a recovery of about 80 per cent, and for the low-grade ore to be upgraded to 53 per cent Sn-WO 3 at the same recovery. However, it is suggested that, under normal mining conditions and with large-scale mining equipment, less fines would be produced and this should lead to an increase in grade and recovery. Mineralogical examinations showed that intermediate fractions produced by tabling contained very few locked particles, and that the grade of the final concentrate on a full-scale plant would probably be higher than that obtained with laboratory equipment. Molybdenite could be a valuable byproduct, but flotation tests of gravity concentrates for selective recovery of the mineral gave variable results. Flotation tests for the removal of fluorspar from the final concentrate were unsuccessful

Increasing the Fine Flaky Graphite Recovery in Flotation via a Combined MultipleTreatments Technique of Middlings

Directory of Open Access Journals (Sweden)

Weijun Peng

2017-11-01

Full Text Available As the residual flaky graphite ores become miscellaneous and fine, a single treatment technique for the middlings from the flotation process of graphite ore cannot efficiently recover the valuable graphite in the multistage grinding-flotation technology. In the study, the existence form of graphite and relationship of graphite with the associated gangue minerals were estimated by optical microscope analysis. The results indicated that the fine flaky graphite particles embedded with gangue minerals like a honeycomb, making it difficult to be beneficiated using the typical flotation technique. A combination technique of individual process and concentrated returning for the treatment of middlings was used to increase the graphite recovery based on the co-existing relationship between graphite and gangue minerals in the middlings. The graphite recovery of the final concentrate upgraded from 51.81% to 91.14% at a fixed carbon (FC content of 92.01% by a beneficiation process consisted of once coarse (94.41% passing 74 μm and rougher, five stages regrinding and six stages cleaning. The proposed treatment technique for middlings is of great significance to increase the recovery of fine flaky graphite.

Measurements of CaF2 concentration in fluorite ore using thermoluminescence techniques

International Nuclear Information System (INIS)

Lembo, L.; Maestri, G.; Pimpinella, M.; Benzi, V.; Muntoni, C.

1990-01-01

Fluorite powder is produced by means of a flotation process on crude ore extracted by the mines. A full automation of the flotation plant would reduce the operating cost and improve the quality and recovery of fluorite production. However, taking into account that the efficiency of a flotation cycle is directly dependent on the CaF 2 content in the concentrate and tail products, this automation requires a quasi-real-time quantitative analysis of CaF 2 concentration in the floated pulp. The feasibility was studied of using a thermoluminescence technique as an on-line analysis method to measure the CaF 2 concentration during the flotation cycle. A first set of experimental conditions to determine CaF 2 content in acid-grade fluorspar has been already developed and the preliminary results so far obtained are presented. (author)

Recovery of uranium from Cu-flotation tails

International Nuclear Information System (INIS)

Jayaram, K.M.V.; Sankaran, R.N.; Dwivedy, K.K.

1984-01-01

Uranium occurs along with copper in several parts of India. Since the total contained uranium in some of these deposits is very large, detailed studies were carried out on samples of ore obtained from Surda, Mosabani and Rakha Cu-flotation tails analysing 0.014 per cent, 0.010 per cent and 0.011 per cent U 3 O 8 and 0.12 per cent 0.09 per cent and 0.11 per cent Cu respectively. Uranium in these samples occurs not only as free uraninite but is also associated with other minerals like apatite, magnetite, tourmaline and micas, formed at different stages of paragenitic sequence. The size also varies considerably. Because of this the recovery of uranium varied from 35 to 70 per cent by wet gravity separation of the feed. Since uranium has to be anyway extracted from these concentrates by hydrometallurgical processing, it is suggested that Cu-flotation tails may be treated by hydrometallurgy to increase the ultimate recovery. (author)

The role of phenols from bagasse vacuum pyrolysis bio-oil in cupper sulfured ore flotation

Directory of Open Access Journals (Sweden)

L. E. Brossard

2008-12-01

Full Text Available Vacuum pyrolysis bagasse bio-oil collected in a series of sequential fractions was analyzed for total percentage of phenols and levoglucosan components. It was established that the ratio total phenols- to-levoglucosan could be used as an indicator of the performance of alkaline solutions of bio-oil fractions (SABO when they are used as foaming agents to benefit flotation of sulfured cupper minerals. A high total phenol-to-levoglucosan ratio results in high percentages of Cu in cupper flotation concentrates, L Cu. A closer look at the role of individual phenols reveals that p-cresol is the main phenol, although not the only one, responsible for the observed behavior. Additionally it was noted that rather high doses of these foaming agents must be used to obtain desirable results in flotation processes. A production cost estimate allows consideration of SABO as an alternative to others commercial foaming agents, especially if an optimization study reduces doses of SABO.

The presentation of leaching and bio-leaching from different ores using SIMPLEX EVOP

OpenAIRE

Krstev, Boris; Krstev, Aleksandar; Golomeova, Mirjana; Gocev, Zivko

2013-01-01

The refractory or low grade lead/zinc domestic ores in Republic of Macedonia are investigated by conventional separation technology or flotation separation. In the mean time, investigations are directed to the new possibilities of leaching by microorganisms – bioleaching. The paper is result of these technologies and investigations carried out for recovery of in the mentioned ores. Using Simplex EVOP and computer program Multisimplex performances are appropriate and most acceptable and exce...

Effect of some column flotation parameters on the fine concentration of phosphate from Itataia, Brazil

International Nuclear Information System (INIS)

Reis Junior, J.B.

1987-01-01

The present investigation aims, at a higher detail level, to identify, from systematic studies, the most important variables of the column flotation and also to check continuous flotation circuits ntegrating columns and mechanical cells to process the -10μm + 3μm fraction from the Itataia ore. The results obtained with the use of only one column as the rougher stage of direct flotation demonstrated a good selectivity, leading to P 2 O 5 and R 2 O 3 (Fe 2 O 3 + Al 2 O 3 ) grade of 24.2 % and 2.79 %, respectively, with p 2 O 5 recovery of 68.5 %. The results of this investigation indicate that the combination of the column concentrate with that of the conventional flotation circuit increases the overall recovery of P 2 O 5 an U 3 O 5 in 5%, in the physical concentration, without impairing the utilization of the final concentrate. (author) [pt

Recovery of rare earth minerals, with emphasis on flotation process

International Nuclear Information System (INIS)

Houot, R.; Cuif, J.P.; Mottot, Y.; Samama, J.C.

1991-01-01

Bastnasite and monazite are the two major minerals used commercially to supply most of the rare earths. Monazite is often a by-product of the concentration of heavy minerals of zirconium and titanium in beach sands. Thus, the methods of concentration are gravity (spirals, Reichert cones and shaking tables), ending with magnetism, electrostatic and in certain cases, flotation. The two main deposits of bastnasite are Mountain Pass (U.S.A.) and Bayan Obo (China). The rock bastnasite content is within 15% and the recovery of rare earth minerals is made through flotation. The flowsheets are complex enough because the existence of accompanying minerals such as quartz, iron components, barite, fluorite, calcite, etc. The conditioning is done by heating and the frequently employed collector is a fatty acid associated with selective agents, as sodium silicate or fluosilicate, lignin sulphonate, sodium carbonate, aluminium salts, etc. Recent studies tempt to introduce the use of phosphoric esters, dicarboxilic, sulphonic and/or sulphosuccinic acids. Concentrates with 60% REO are then treated with acidic solution to eliminate residual calcite. The possibility of obtaining products enriched with rare earths are also noted: these are ores of uranium (Elliot Lake), pyrochlore, apatite, and other complex ores with euxenite, fergusonite or loparite. (author) 10 figs., 6 tabs., 57 refs

Preconcentration of a low-grade uranium ore yielding tailings of greatly reduced environmental concerns. Part V

International Nuclear Information System (INIS)

Raicevic, D.; Raicevic, M.

1980-11-01

The low-grade ore sample used for this investigation contained 0.057 percent uranium with uranothorite as the major uranium-bearing mineral and a small amount of brannerite, occurring in the quartz-sericite matrix of a conglomerate. The preconcentration procedures, consisting of pyrite flotation with or without flotation of radioactive minerals, followed by high intensity wet magnetic treatment of the sized flotation tailings, produced pyrite and radioactive concentrates of acceptable uranium grades ranging from 0.1 to 0.135 percent uranium. The combined concentrates comprised 37 to 49 percent of the ore by weight with the following combined recoveries: 95.6 to 97.9 percent of the uranium; 94.7 to 96.3 percent of the radium; 97.8 to 99.3 percent of the thorium over 98 percent of the pyrite. The preconcentration tailings produced comprised between 51 and 63 percent of the ore by weight and contained from: 0.0022 to 0.0037 percent U; 12 to 17 pCi/g Ra; 0.002 to 0.004 percent Th less than 0.03 percent S. Because these tailings are practically pyrite-free, they should not generate acidic conditions. Due to their low radium content, their radionuclide hazards are greatly reduced. These preconcentration tailings therefore, could be suitable for surface disposal, mine backfill, revegetation or other uses

The impact of new technology on the economics of uranium production from low-grade ores

International Nuclear Information System (INIS)

Simonsen, H.A.; Boydell, D.W.; James, H.E.

1981-01-01

The subject is discussed under the following headings: influence of a depressed market on uranium supply from low-grade ores; potential areas for a reduction in uranium ore processing costs; in-situ leaching (solution mining; heap leaching; resin-in-pulp; solvent-in-pulp; belt filtration; continuous ion exchange; solvent extraction); preconcentration (upgrading of coarse rock; upgrading in the mill; wet high-intensity magnetic separation; flotation); summary and conclusions. (U.K.)

Complex sulphide-barite ore leaching in ferric chloride solution

Directory of Open Access Journals (Sweden)

Miroslav Sokić

2016-06-01

Full Text Available The results of research on the leaching process of complex sulphide-barite ore were presented in this paper. The leaching process was carried out in a laboratory autoclave by ferric chloride solution. Considering that those minerals are represented in complex structural-textural relationships, it is not possible to extract lead, zinc and copper minerals from ore by flotation methods. The obtained results confirmed possibility of the ore processing directly, by chemical methods. The effect of temperature, time and oxygen partial pressure on the lead, zinc and copper dissolution was studied. The maximal leaching degree was achieved at 100 °C and amount of 91.5 % for Pb, 96.1 % for Zn and 60.7 % for Cu. Leaching at temperatures above 100 °C is impractical.

Effect of reagent type on the froth floatation of Sokoto phosphate ore

Directory of Open Access Journals (Sweden)

U.A. Hassan

2016-06-01

Full Text Available Effect of reagent type on the froth floatation of Sokoto phosphate ore for its beneficiation has been established. The samples of the Sokoto phosphate mineral ore used for the research work were sourced from mining locations in Dange-Shuni, Bodinga, Yabo, Wurno, and Rabbah Local Government Areas of Sokoto State. Size-Assay analysis conducted on scrubbed Sokoto Phosphates nodules revealed that nodules had a size distribution with 80% passing 29.3 mm. Flotation Tests using AERO704 (fatty Acid, Alkyl Hydroxamates, Melamine as collectors (alone or mixed with diesel, MIBC as frother, Calcium Hydroxide and Sulphuric Acid as pH regulators and Dextrin, Sodium Silicate and Aluminium Chloride as depressants produced poor P2O5 separation in the flotation products due to very poor liberation associated with very fine mineral grains. Based on the results obtained, AERO704 Collector gave the best result with aP2O5 recovery pH of 10.

Preconcentration of low-grade uranium ores with environmentally acceptable tailings, part I

International Nuclear Information System (INIS)

Raicevic, D.; Raicevic, M.; McCarthy, D.R.

1979-08-01

The low-grade ore sample used for this investigation originated from Agnew Lake Mines Limited, Espanola, Ontario. It contained about 1% pyrite and 0.057% uranium, mainly as uranothorite with a small amount of brannerite. Both of these minerals occur in the quartz-sericite matrix of a conglomerate. A preconcentration process has been developed to give a high uranium recovery, reject pyrite, radium and thorium from the ore and produce environmentally acceptable tailings. This process applies flotation in combination with high intensity magnetic separation and gravity concentration

Leaching of U, 230Th and 226Ra from Saskatchewan uranium ore after removing clay

International Nuclear Information System (INIS)

Muthuswami, S.V.; Mohd Yunus, M.Z.; Mohamad Nor, M.I.; Kassim, Z.A.; Nirdosh, I.

1993-01-01

Distribution of U, 230 Th and 226 Ra in various size fractions in a typical Saskatchewan uranium ore and its resultant mill tailings indicated that less than 4% of these radionuclides were present in the fine ≤ 45 μm) size fraction in the ore whereas their concentration in the similar size fraction in the tailings was > 80%. Removal of clay minerals from the ore by flotation was unsuccessful whereas sedimentation gave nearly complete removal. Leaching of 230 Th from the ore before and after removing clay minerals indicated that dissolution of 230 Th was mproved at higher E h and acidity of the leaching medium and that it was independent of the presence of clay minerals in the ore. (orig.) [de

Some developments in the extraction of gold from Witwatersrand ores

International Nuclear Information System (INIS)

Laxen, P.A.

1975-01-01

The extraction of gold from most ores of the Witwatersrand has been consistently high - approximately 95 per cent - for many years. The present high price of gold has stimulated research and development into potential improvements of the standard procedures. The occurrence of the gold and its association with other minerals is described briefly. The Witwatersrand reefs also contain uranium and pyrite, and some of the improvements to the standard gold-extraction process are associated with the recovery or concentration of one or both of these valuable constituents. For instance, the 'reverse-leach' process, in which acid treatment for the extraction of uranium precedes cyanidation, results in improved gold extraction. Some concentration techniques used on the present residues from cyanidation offer promise in improving the overall gold recoveries. Thucholite is an important carrier of residual gold, and its recovery from some residues by flotation appears to be economically justifiable. Wet high-intensity magnetic separation has given promising results, in the laboratory and on the pilot plant, for the recovery of both uranium and gold from a number of cyanide tailings. The benefits of gravity concentration and of the application of empirical modelling to the gold-extraction process have been demonstrated by a mining group. Some developments in instrumentation for control during cyanidation are discussed briefly [af

Beneficiation of feldspar ore for application in the ceramic industry: Influence of composition on the physical characteristics

OpenAIRE

Gaied, M.E.; Gallala, W.

2015-01-01

In this study, physical and physicochemical experiments were carried out to improve the quality of feldspar ore in Sidi Aïch massive, located in the Gafsa region of south-western Tunisia. After determination of the mineralogical and the chemical composition, flotation methods were applied. In this study, non-hydrofluoric acid flotation methods used in feldspar-quartz separation were compared with each other and with the conventional HF/amine method. The results showed that conventional HF/ami...

Composition suitable as collection agent in ore flotation process and preparation of said composition

International Nuclear Information System (INIS)

Bresson, C.R.; Parlman, R.M.

1984-01-01

A composition and process are provided for the recovery of the values of zinc, molybdenum, copper, lead, ion (pyrite), and iron-containing small amounts of gold or uranium, or both, from ores comprising these mineral sulfides. The aqueous composition is the impure form of an alkali metal alkyl trithiocarbonate compound. The process comprises employing said aqueous composition as a collection agent for the above minerals in an ore recovery process. A process for the separation of zinc values from lead values from an ore comprising both is provided by employing an alkali metal alkyl trithiocarbonate compound as a collection agent for zinc. In addition, both a composition and process are provided for the recovery of the values of iron, copper, and lead from ores comprising these values. The composition consists essentially of a dispersant and an impure form of an alkali metal alkyl trithiocarbonate compound. The process comprises employing this composition as a collection agent for the above minerals in an ore recovery process

Microwave enhanced recovery of nickel-copper ore: communition and floatability aspects.

Science.gov (United States)

Henda, R; Hermas, A; Gedye, R; Islam, M R

2005-01-01

A study describing the effect of microwave radiation, at a frequency of 2450 MHz, on the processes of communication and flotation of a complex sulphide nickel-copper ore is presented. Ore communication has been investigated under standard radiation-free conditions and after ore treatment in a radiated environment as a function of ore size, exposure time to radiation, and microwave power. The findings show that communication is tremendously improved by microwave radiation with values of the relative work index as low as 23% at a microwave power of 1.406 kW and after 10 s of exposure time. Communication is affected by exposure time and microwave power in a nontrivial manner. In terms of ore floatability, the experimental tests have been carried out on a sample of 75 microm in size under different exposure times. The results show that both ore concentrate recoveries and grades of nickel and copper are significantly enhanced after microwave treatment of the ore with relative increases in recovered concentrate, grade of nickel, and grade of copper of 26 wt%, 15 wt%, and 27%, respectively, at a microwave power of 1330 kW and after 30 s of exposure time.

Flotation process control optimisation at Prominent Hill

International Nuclear Information System (INIS)

Lombardi, Josephine; Muhamad, Nur; Weidenbach, M.

2012-01-01

OZ Minerals' Prominent Hill copper- gold concentrator is located 130 km south east of the town of Coober Pedy in the Gawler Craton of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a 9.6 Mtpa ore throughput capacity. The flotation circuit includes six rougher cells, an IseMill for regrinding the rougher concentrate and a Jameson cell heading up the three stage conventional cell cleaner circuit. In total there are four level controllers in the rougher train and ten level controllers in the cleaning circuit for 18 cells. Generic proportional — integral and derivative (PID) control used on the level controllers alone propagated any disturbances downstream in the circuit that were generated from the grinding circuit, hoppers, between cells and interconnected banks of cells, having a negative impact on plant performance. To better control such disturbances, FloatStar level stabiliser was selected for installation on the flotation circuit to account for the interaction between the cells. Multivariable control was also installed on the five concentrate hoppers to maintain consistent feed to the cells and to the IsaMill. An additional area identified for optimisation in the flotation circuit was the mass pull rate from the rougher cells. FloatStar flow optimiser was selected to be installed subsequent to the FloatStar level stabiliser. This allowed for a unified, consistent and optimal approach to running the rougher circuit. This paper describes the improvement in the stabilisation of the circuit achieved by the FloatStar level stabiliser by using the interaction matrix between cell level controllers and the results and benefits of implementing the FloatStar flow optimiser on the rougher train.

Flotation in column applied to fines of the Itataia phosphoro-uraniferous ore, CE, Brazil

International Nuclear Information System (INIS)

Furtado, J.R.V.; Peres, A.E.C.

1985-01-01

An adequate process to treat the fine fraction was developed in the present investigation, after size and chemical characterization of the fines,. Emphasis was placed on construction, assembling and operation of a 5.2 cm diameter and 6.0 m high continuos flotation column. The column was fed with the pilot plant desliming cyclone overflow, below 10 m. Tests were also carried out with the underflow of the same cyclone and with the very fine underflow of a 20 mm cyclone. The column presented a better performance than a rougher laboratory mechanical cell when tested with the underflow of 20 mm cyclone. Concentrates with 24.5% P 2 O 5 , with recovery levels above 60% were achieved from feed grades of 10.3%P 2 O 5 , it is worth mentioning that the rougher flotation reagents scheme is not effective to deppress carbonatic gangue irrespective of the size range. (Author) [pt

N-(6-(hydroxyamino)-6-oxohexyl) decanamide collector: Flotation performance and adsorption mechanism to diaspore

Energy Technology Data Exchange (ETDEWEB)

Deng, Lanqing [College of Chemistry and Chemical Engineering, Central South University, Changsha 410083 (China); Key Laboratory of Yueyang Chinese Herbal Utilization, Yueyang Vocational Technical College, Yueyang 414000 (China); Wang, Shuai [College of Chemistry and Chemical Engineering, Central South University, Changsha 410083 (China); Zhong, Hong, E-mail: zhongh@csu.edu.cn [College of Chemistry and Chemical Engineering, Central South University, Changsha 410083 (China); Liu, Guangyi, E-mail: guangyiliu@csu.edu.cn [College of Chemistry and Chemical Engineering, Central South University, Changsha 410083 (China)

2015-08-30

Graphical abstract: The potential absorption model of NHOD on diaspore surface. - Highlights: • A novel surfactant NHOD was first introduced as diaspore flotation collector. • NHOD exhibited superior collecting power to diaspore against gangue. • NHOD's has double active centers to mineral surfaces and double hydrophobic groups. • NHOD molecules formed intermolecular hydrogen bonds on diaspore surfaces. - Abstract: In this paper, a novel surfactant, N-(6-(hydroxyamino)-6-oxohexyl)decanamide (NHOD) was synthesized and used as a collector for flotation separation of diaspore and aluminosilicate minerals. The adsorption mechanism of NHOD onto diaspore was also investigated by FTIR spectra, zeta potential measurement and XPS. The flotation results demonstrated that NHOD exhibited superior collecting power to diaspore and selectivity against kaolinite and illite and could effectively realize flotation recovery of diaspore from bauxite ores contained aluminosilicate minerals under neutral conditions. The results of XPS, FTIR spectra and zeta potential illustrated that at around pH 7.0, NHOD might chemisorb on diaspore surfaces through Al−O coordination bonds formed by binding its −C(=O)NHOH or −C(=O)NH− chelate groups with aluminum atoms on diaspore surfaces. NHOD's unique properties, such as characteristic bond patterns onto diaspore surfaces, two hydrophobic groups, and intermolecular hydrogen bonds between neighboring NHOD molecules coated on diaspore surfaces, rendered it to be a superior flotation collector for diaspore.

N-(6-(hydroxyamino)-6-oxohexyl) decanamide collector: Flotation performance and adsorption mechanism to diaspore

International Nuclear Information System (INIS)

Deng, Lanqing; Wang, Shuai; Zhong, Hong; Liu, Guangyi

2015-01-01

Graphical abstract: The potential absorption model of NHOD on diaspore surface. - Highlights: • A novel surfactant NHOD was first introduced as diaspore flotation collector. • NHOD exhibited superior collecting power to diaspore against gangue. • NHOD's has double active centers to mineral surfaces and double hydrophobic groups. • NHOD molecules formed intermolecular hydrogen bonds on diaspore surfaces. - Abstract: In this paper, a novel surfactant, N-(6-(hydroxyamino)-6-oxohexyl)decanamide (NHOD) was synthesized and used as a collector for flotation separation of diaspore and aluminosilicate minerals. The adsorption mechanism of NHOD onto diaspore was also investigated by FTIR spectra, zeta potential measurement and XPS. The flotation results demonstrated that NHOD exhibited superior collecting power to diaspore and selectivity against kaolinite and illite and could effectively realize flotation recovery of diaspore from bauxite ores contained aluminosilicate minerals under neutral conditions. The results of XPS, FTIR spectra and zeta potential illustrated that at around pH 7.0, NHOD might chemisorb on diaspore surfaces through Al−O coordination bonds formed by binding its −C(=O)NHOH or −C(=O)NH− chelate groups with aluminum atoms on diaspore surfaces. NHOD's unique properties, such as characteristic bond patterns onto diaspore surfaces, two hydrophobic groups, and intermolecular hydrogen bonds between neighboring NHOD molecules coated on diaspore surfaces, rendered it to be a superior flotation collector for diaspore

Obtention of high purity silica from the flotation waste of itabiritic ore

International Nuclear Information System (INIS)

Martins, Polyana Fabricia Fernandes

2016-01-01

Banded iron formations are exploited as iron mineral in 'Quadrilatero Ferrifero' of Minas Gerais (MG) State, Brazil. About half of the amount of extracted material becomes tailings, which are stored in tailing dams or used for filling mining pits. Tens of thousands of tons are generated daily in operating mines in this region, causing concern about the environmental liabilities, and costs to manage the tailing dams. Miners are committed to finding uses for these wastes in other productive chains. This thesis aimed to obtain high purity silica from the flotation tailings of banded iron formations using classical techniques for ore processing, such as particle size classification and magnetic separation, followed by hydrometallurgical leaching, also alkaline fusion and chemical precipitation. The tailings samples was collected in the tailings dam of Peak Mine operated by Vale A.S., in Itabirito – MG. This sample had initially 33.4% by weight SiO 2 , 57.4% wt Fe 2 O 3 and 8.31% wt Al 2 O 3 . After desliming for disposal of the fine particles (-37μm) the composition was 68.0% SiO 2 , 31.4% Fe 2 O 3 and 0.50% Al 2 O 3 . After magnetic separation, the composition was 93.8% SiO 2 , 1.16% Fe 2 O 3 and 3.80% Al 2 O 3 . After acid leaching l or digestion to remove impurities, it was possible to obtain silica with 98% purity. The fusion with sodium hydroxide, followed by alkaline leaching of sodium silicate and silica precipitation gave purities of about 99.5%. Values even higher may be possible with optimization of the parameters of alkaline fusion or by repeating the process from the product with purity of 99.5%. The iron oxide content and the aluminum main contaminants were 0.01% and 0.07%, respectively. Amorphous silica was obtained with high specific surface (322 m 2 /g) and particle size less than 200 nm. Depending on the application, a control should be made for the impurities, such as phosphorus, potassium and boron. (author)

Effect of particle size on the froth floatation of Sokoto phosphate ore

Directory of Open Access Journals (Sweden)

U.A. Hassan

2016-06-01

Full Text Available Effect of particle size on the froth floatation of Sokoto phosphate ore for its beneficiation has been investigated and established. The research has been conducted using various reagents, pH(s at different sieve size fractions. Bench scale flotation tests were carried out on -250+180μm, -180+106μm, -106+75μm, -75+45μm and -45+38μm particle size fractions after screening in order to determine the optimum flotation feed size distribution using 1 liter Denver flotation cell. The results of the scoping flotation studies using a conditioning Pulp Density of 60%Solids, pH9, 800g/t reagent dosage for AERO704 Promoter (Fatty Acid and flotation pulp density of 28.5% Solids show that +106μm particle size gave the highest assay content of 20.4% P2O5 with a recovery of 76.2% compared to +38μm (19.9%P2O5 and recovery of 43.2% and +180μm (19.4%P2O5 and 24.1% recovery in their floats (concentrates but with no perfect separation as the tailings fraction also contained similar grades with slight differences.

Thermodynamic Analysis of the Selective Reduction of a Nickeliferous Limonitic Laterite Ore by Hydrogen

Science.gov (United States)

Elliott, R.; Pickles, C. A.

2017-09-01

Nickeliferous limonitic laterite ores are becoming increasingly attractive as a source of metallic nickel as the costs associated with recovering nickel from the sulphide ores increase. Unlike the sulphide ores, however, the laterite ores are not amenable to concentration by conventional mineral processing techniques such as froth flotation. One potential concentrating method would be the pyrometallurgical solid state reduction of the nickeliferous limonitic ores at relatively low temperatures, followed by beneficiation via magnetic separation. A number of reductants can be utilized in the reduction step, and in this research, a thermodynamic model has been developed to investigate the reduction of a nickeliferous limonitic laterite by hydrogen. The nickel recovery to the ferronickel phase was predicted to be greater than 95 % at temperatures of 673-873 K. Reductant additions above the stoichiometric requirement resulted in high recoveries over a wider temperature range, but the nickel grade of the ferronickel decreased.

Preconcentration of a low grade uranium ore in CPDU and laboratory investigation to optimize the dewatering conditions of the preconcentration products

International Nuclear Information System (INIS)

Cristovici, M.A.; Berry, T.F.; Raicevic, M.M.; Brady, E.L.; Bredin, E.L.; Leigh, G.W.; Rouleau, J.P.

1982-04-01

A process consisting of pyrite flotation and magnetic concentration of radionuclides was developed by CANMET over several years, to preconcentrate low grade uranium ores prior to leaching. When the economics of the preconcentration-leaching technology was compared with the leaching of the entire ore after pyrite flotation (Base Case variant), the preconcentration method appeared to be economically less advantageous than expected, due to the high cost of dewatering the preconcentration products. Further investigations examined in-depth the metallurgy and dewatering of the two variants: preconcentration and base case. A typical low grade uranium ore from Elliot Lake area was used. The metallurgy was compared based on data from continuous operation (CPDU). In the preconcentration variant the amount of ore directed to leaching was reduced to more than one third of that processed in the base case, while the radionuclide concentration became more than three times higher. However, by preconcentration 7% of the uranium was lost before leaching. Systematic laboratory-scale settling and filter tests optimized the dewatering conditions of the preconcentration technology to the extent that rates similar to those of the base case were obtained

Model Predictive Control of Mineral Column Flotation Process

Directory of Open Access Journals (Sweden)

Yahui Tian

2018-06-01

Full Text Available Column flotation is an efficient method commonly used in the mineral industry to separate useful minerals from ores of low grade and complex mineral composition. Its main purpose is to achieve maximum recovery while ensuring desired product grade. This work addresses a model predictive control design for a mineral column flotation process modeled by a set of nonlinear coupled heterodirectional hyperbolic partial differential equations (PDEs and ordinary differential equations (ODEs, which accounts for the interconnection of well-stirred regions represented by continuous stirred tank reactors (CSTRs and transport systems given by heterodirectional hyperbolic PDEs, with these two regions combined through the PDEs’ boundaries. The model predictive control considers both optimality of the process operations and naturally present input and state/output constraints. For the discrete controller design, spatially varying steady-state profiles are obtained by linearizing the coupled ODE–PDE model, and then the discrete system is obtained by using the Cayley–Tustin time discretization transformation without any spatial discretization and/or without model reduction. The model predictive controller is designed by solving an optimization problem with input and state/output constraints as well as input disturbance to minimize the objective function, which leads to an online-solvable finite constrained quadratic regulator problem. Finally, the controller performance to keep the output at the steady state within the constraint range is demonstrated by simulation studies, and it is concluded that the optimal control scheme presented in this work makes this flotation process more efficient.

Radioisotopes investigations of copper ore dressing processes

International Nuclear Information System (INIS)

Petryka, L.; Furman, L.; Przewlocki, K.; Stegowski, Z.

1992-01-01

This paper describes radioisotope applications in the copper industry, mainly for the examination of comminution, classification, and flotation processes for selected physical parameters. Measurements were performed by a mobile laboratory containing the electronics for experiment control and data recording and processing using special computer software. This system makes it possible to determine measurements in an industrial environment. The data acquisition system provides 24 spectrometric channels, consisting of scintillation probes, high-voltage (HV) power supplies, and pulse-height analyzers, as well as an analog-to-digital (A/D) converter interfaced to the IBM personal computer. The sampling time is fully programmable and interrupt based and can vary from 1 ms to hours and may be set separately for each channel. The milli-second sampling time technique has been applied to high-resolution flow velocity measurements. On the other hand, longer sampling time enables the system to be left unattended for days to monitor, for example, copper ore concentration or efficiency of the flotation process

Determination of rare earth elements in products of Chadormalu iron ore concentrator plant (Iran) from beneficiation point of view

International Nuclear Information System (INIS)

Jorjani, E.; Bagherieh, A. H.; Rezai, B.

2007-01-01

:Different samples have been prepared from different products in Chadormalu iron ore concentrator plant: Low intensity magnetite separators concentrate (magnetite concentrate), reverse flotation tail (final hematite concentrate), flotation concentrate (apatite concentrate), final tail (L.I. M.S. tail + reverse flotation concentrate + apatite flotation tail). The samples were used for rare earth elements (REEs) distribution and origin studies. The assay of REEs was determined by ICP-MS spectrometry. The amount of total (light and heavy) REEs were 9631, 291, 199, 2236 ppm and the distributions were 19.3, 3.6, 10.1, 67% in flotation concentrate (apatite concentrate), reverse flotation tail (hematite concentrate), magnetite concentrate and total tail respectively. About 19.3% of total REEs were distributed in apatite concentrate with an assay of 9631 ppm. Therefore, further studies have been conducted on this product. According to the Xray studies the minerals of fluoroapatite, ankerite and calcite are the main mineral phases in apatite concentrate which the apatite is dominant among them. The scanning electron microscopy studies were shown that the high amount of REEs distributed on fluoroapatite mineral. The results have clearly shown that the apatite concentrate that is a by product of iron dressing in Chadormalu plant, with a low economical value and left without any further treatment, can be used as a significant source of REEs. According to this characterization studies, the recovery of a mixed rare earth oxide from fluoroapatite is possible either with the treatment of liquors from the total dissolution of the ore in nitric acid or with the proposed treatment of the phosphogypsum by-product from the conventional sulphuric acid route and the recovery of rare earth oxides from phosphoric acid sludges that the detailed flowsheet needs further extraction work

Taguchi optimization: Case study of gold recovery from amalgamation tailing by using froth flotation method

Science.gov (United States)

Sudibyo, Aji, B. B.; Sumardi, S.; Mufakir, F. R.; Junaidi, A.; Nurjaman, F.; Karna, Aziza, Aulia

2017-01-01

Gold amalgamation process was widely used to treat gold ore. This process produces the tailing or amalgamation solid waste, which still contains gold at 8-9 ppm. Froth flotation is one of the promising methods to beneficiate gold from this tailing. However, this process requires optimal conditions which depends on the type of raw material. In this study, Taguchi method was used to optimize the optimum conditions of the froth flotation process. The Taguchi optimization shows that the gold recovery was strongly influenced by the particle size which is the best particle size at 150 mesh followed by the Potassium amyl xanthate concentration, pH and pine oil concentration at 1133.98, 4535.92 and 68.04 gr/ton amalgamation tailing, respectively.

Study On Beneficiation Technology Of Dong Pao Rare-Earth-Barite-Fluorite With Two Product Plans About Content And Recovery Of Rare-Earth Fine Ores

International Nuclear Information System (INIS)

Duong Van Su; Truong Thi Ai; Bui Ba Duy; Bui Thi Bay; Nguyen Hong Ha; Le Thi Hong Ha; Doan Thi Mo; Doan Dac Ban; Nguyen Hoang Son

2014-01-01

The ore sample used in the research was taken from the F3 ore bodies and the sample of the F7, F9 and F16 ore bodies which contain the average of 5.98% TR 2 O 3 ; they are multi-metals ore which is difficult to enrich, highly weather with very complex ingredients. The process of the experiment is the ore is crushed, ground, screened and classified reasonably to -0.1 mm and divided into 3 particle size with the following technique: (1) -0.020 mm is primary sludge and the rare-earth fine ore; (2) 0.075-1 mm is gotten through the sludge concentrating table with the output is the 2 parts: the heavy part which is dried magnetic separator with high magnetism to get the rare-earth fine ore and the light one; (3) Light minerals, non-magnetic and ferromagnetic minerals group are ground together to 85% of them get size within -0.075 mm then mix it with 0.020-0.075 mm group. Using flotation separator, get barite-rare earth mixture and fluorite. After that, we separate this mixture by secondary flotation and get refined rare earth, barite and fluorite mineral. The result of the theme: (1) product plan A-rare-earth fine ore has TR 2 O 3 content archive 42.07% with recovery is 69.70%; (2) product plan B-rare-earth fine ore has TR 2 O 3 content archive 29.64% with recovery is 80.01%. (author)

New influence factor inducing difficulty in selective flotation separation of Cu-Zn mixed sulfide minerals

Science.gov (United States)

Deng, Jiu-shuai; Mao, Ying-bo; Wen, Shu-ming; Liu, Jian; Xian, Yong-jun; Feng, Qi-cheng

2015-02-01

Selective flotation separation of Cu-Zn mixed sulfides has been proven to be difficult. Thus far, researchers have found no satisfactory way to separate Cu-Zn mixed sulfides by selective flotation, mainly because of the complex surface and interface interaction mechanisms in the flotation solution. Undesired activation occurs between copper ions and the sphalerite surfaces. In addition to recycled water and mineral dissolution, ancient fluids in the minerals are observed to be a new source of metal ions. In this study, significant amounts of ancient fluids were found to exist in Cu-Zn sulfide and gangue minerals, mostly as gas-liquid fluid inclusions. The concentration of copper ions released from the ancient fluids reached 1.02 × 10-6 mol/L, whereas, in the cases of sphalerite and quartz, this concentration was 0.62 × 10-6 mol/L and 0.44 × 10-6 mol/L, respectively. As a result, the ancient fluid is a significant source of copper ions compared to mineral dissolution under the same experimental conditions, which promotes the unwanted activation of sphalerite. Therefore, the ancient fluid is considered to be a new factor that affects the selective flotation separation of Cu-Zn mixed sulfide ores.

Utilization of flotation wastes of copper slag as raw material in cement production

International Nuclear Information System (INIS)

Alp, I.; Deveci, H.; Suenguen, H.

2008-01-01

Copper slag wastes, even if treated via processes such as flotation for metal recovery, still contain heavy metals with hazardous properties posing environmental risks for disposal. This study reports the potential use of flotation waste of a copper slag (FWCS) as iron source in the production of Portland cement clinker. The FWCS appears a suitable raw material as iron source containing >59% Fe 2 O 3 mainly in the form of fayalite (Fe 2 SiO 4 ) and magnetite (Fe 3 O 4 ). The clinker products obtained using the FWCS from the industrial scale trial operations over a 4-month period were characterised for the conformity of its chemical composition and the physico-mechanical performance of the resultant cement products was evaluated. The data collected for the clinker products produced using an iron ore, which is currently used as the cement raw material were also included for comparison. The results have shown that the chemical compositions of all the clinker products including those of FWCS are typical of a Portland cement clinker. The mechanical performance of the standard mortars prepared from the FWCS clinkers were found to be similar to those from the iron ore clinkers with the desired specifications for the industrial cements e.g. CEM I type cements. Furthermore, the leachability tests (TCLP and SPLP) have revealed that the mortar samples obtained from the FWCS clinkers present no environmental problems while the FWCS could act as the potential source of heavy metal contamination. These findings suggest that flotation wastes of copper slag (FWCS) can be readily utilised as cement raw material due to its availability in large quantities at low cost with the further significant benefits for waste management/environmental practices of the FWCS and the reduced production and processing costs for cement raw materials

Utilization of flotation wastes of copper slag as raw material in cement production.

Science.gov (United States)

Alp, I; Deveci, H; Süngün, H

2008-11-30

Copper slag wastes, even if treated via processes such as flotation for metal recovery, still contain heavy metals with hazardous properties posing environmental risks for disposal. This study reports the potential use of flotation waste of a copper slag (FWCS) as iron source in the production of Portland cement clinker. The FWCS appears a suitable raw material as iron source containing >59% Fe(2)O(3) mainly in the form of fayalite (Fe(2)SiO(4)) and magnetite (Fe(3)O(4)). The clinker products obtained using the FWCS from the industrial scale trial operations over a 4-month period were characterised for the conformity of its chemical composition and the physico-mechanical performance of the resultant cement products was evaluated. The data collected for the clinker products produced using an iron ore, which is currently used as the cement raw material were also included for comparison. The results have shown that the chemical compositions of all the clinker products including those of FWCS are typical of a Portland cement clinker. The mechanical performance of the standard mortars prepared from the FWCS clinkers were found to be similar to those from the iron ore clinkers with the desired specifications for the industrial cements e.g. CEM I type cements. Furthermore, the leachability tests (TCLP and SPLP) have revealed that the mortar samples obtained from the FWCS clinkers present no environmental problems while the FWCS could act as the potential source of heavy metal contamination. These findings suggest that flotation wastes of copper slag (FWCS) can be readily utilised as cement raw material due to its availability in large quantities at low cost with the further significant benefits for waste management/environmental practices of the FWCS and the reduced production and processing costs for cement raw materials.

Selective depression mechanism of ferric chromium lignin sulfonate for chalcopyrite-galena flotation separation

Science.gov (United States)

Yu, Jin-sheng; Liu, Run-qing; Wang, Li; Sun, Wei; Peng, Hong; Hu, Yue-hua

2018-05-01

Selective recovery of chalcopyrite-galena ore by flotation remains a challenging issue. The development of highly efficient, low-cost, and environmentally friendly depressants for this flotation is necessary because most of available reagents (e.g., K2Cr2O4) are expensive and adversely affect the environment. In this study, ferric chromium lignin sulfonate (FCLS), which is a waste-product from the paper and pulp industry, was introduced as a selective depressant for galena with butyl xanthate (BX) as a collector. Results show that the residue recovery of Pb in Cu concentrate was substantially reduced to 4.73% using FCLS compared with 10.71% using the common depressant K2Cr2O4. The underlying mechanisms were revealed using zeta-potential measurements and X-ray photoelectron spectroscopy (XPS). Zeta-potential measurements revealed that FCLS was more efficiently absorbed onto galena than onto chalcopyrite. XPS measurements further suggested that FCLS enhanced the surface oxidation of galena but prevented that of chalcopyrite. Thus, FCLS could be a potential candidate as a depressant for chalcopyrite-galena flotation because of its low cost and its lack of detrimental effects on the environment.

Determination Of Rare Earth And Other Elements In YEN-PHU Rare Earth Ore And Other Intermediate Products From The Floatation And Hydrometallurgical Process On Portable XRF Si-PIN Detector

International Nuclear Information System (INIS)

Doan Thanh Son; Phung Vu Phong; Nguyen Hanh Phuc

2014-01-01

The concentration of rare earths elements such as La, Ce, Pr, Nd, Gd and other elements as Ca, Fe, U, Th in Yen Phu rare earth ore and other intermediate products from the flotation and hydrometallurgical process was determined by using Si-PIN detector fluorescence spectrometry. The precision and accuracy of quantitative analysis was tested by standard reference materials and comparative analysis with different analytical methods. The analytical procedures were set-up and applied for the determination of rare earth and other elements in Yen Phu rare earth ore and other intermediate products from the flotation and hydrometallurgical process with high precision and accuracy. (author)

Operating a pneumatic-mechanical flotation machine for coal-slurry flotation

Energy Technology Data Exchange (ETDEWEB)

Shmaenok, N M; Bedran, N G; Konstantinov, V K; Kochetkov, Yu I; Sysoev, V S

1976-01-01

The FPM-GMO-1.6 pneumatic-mechanical flotation machine is easy to operate and regulate and maintains a high throughput at a low energy consumption. The flotation process is stable, the quality of the concentrate and tailings satisfactory, and the selectivity of separation high. The machine cannot handle coal slurries at higher throughputs because the rate of froth removal is too low across the entire flotation front. Experience on the pneumatic-mechanical flotation machine at the ''Kolosnikovskaya'' Central Washery indicates that a similar machine should be developed for a throughput of 1000 m/sup 3//hr.

Pyrolitics Oils in Coal Flotation

OpenAIRE

Čáblík, V.; Išek, J.; Herková, M.; Halas, J.; Čáblíková, L.; Vaculíková, L. (Lenka)

2014-01-01

The aim of this article was the research of new flotation reagents, which were formed through pyrolysis of different types of waste. Potential new flotation reagents are liquid organic phase pyrolysis of tires, plastic and wooden materials. Another goal is to achieve the coal flotation ash content quality below 10%. The results imply that it is possible to produce flotation collectors from various types of waste, which may be applicabe in black coal flotation. Producing and application of a s...

Coagulation of fines in fluorite froth flotation; Coagulacion de finos en la flotacion de la fluorita

Energy Technology Data Exchange (ETDEWEB)

Sarquis, P. E.; Gonzalez, M.; Moyano, A.; Bazan, V.

2011-07-01

Fluorite, a valuable mineral in the metallurgical industry, can be found together with silicates, carbonates and oxides in ore deposits. Commercial concentrates with more than 95 % of CaF{sub 2} are obtained processing the mineral in flotation plants and using oleic acid as fluorite collector. Depressor reagents such as sodium silicate, tannin and sodium carbonate are commonly employed to allow the oleic acid selective performance. These reagents cause a dispersant effect separating the solid-liquid solution on tailing plants. Fine particles in the recovered water enter the circuit and affect the flotation efficiency. The effect of coagulant ions was studied as a method to clarify the returned water. The problem of the presence of these ions is related to its reactions with the collector by the formation of compounds and possibly on the selectivity. Variable quantities of Al{sup 3}+, Fe{sup 3}+ and Ca{sup 2}+ ions were added to the flotation to evaluate its effect on the fluorite recovery, in the selectivity and in solids content in recirculation water. Results show that some ions fail to improve water quality and are detrimental to flotation. On the contrary, some ions contribute to reduce fine content in suspension. Therefore, although there is a recovery reduction, such effect can be counteracted increasing the collector consumption a little. (Author) 21 refs.

Enhancement of Cu, Ni and Mo recoveries in the bulk concentrate of Jaduguda uranium bearing ore

International Nuclear Information System (INIS)

Rao, G.V.; Besra, L.D.

1998-01-01

The uranium ore treatment plant at Jaduguda, India, recovers copper, nickel and molybdenum as byproducts before the bulk flotation tailings are subjected to leaching to recover uranium values. The recoveries of these sulfide metals in this 900 TPD plant are reported to be around 60 % Cu, 25% Ni and 55% Mo in the bulk concentrate. In this article, flotation studies carried out, at the instance of M/S UCIL, with various reagents and their combination to improve the over all recoveries are presented. It was observed that material coarser than 100 microns, from the flotation feed, could not be floated even in presence of excessive reagent unless it is ground further. It was established that around 95% Cu, 75% Ni and 74% Mo values could be recovered by using either amyl xanthate or mixture of amyl xanthate and Aero Promoter 194 in place of cresylic acid that is being currently used as collector in the plant. (author)

Flotation as a remediation technique for heavily polluted dredged material. 2. Characterisation of flotated fractions.

Science.gov (United States)

Cauwenberg, P; Verdonckt, F; Maes, A

1998-01-19

The particle size distribution and the metal speciation of the heavy metals were investigated on dredged sediment and on the fractions obtained by mechanical agitated (Denver) flotation. The transition metal ions (cadmium, copper, lead and zinc) were flotated specifically independent of the particle size. Particle size analysis, EDTA extraction and sequential extracts indicated that during flotation a redistribution of metals occurred due to the oxidation of metal sulphides. This oxidation process was more pronounced when the flotation was performed at higher pH values and resulted in a decrease in flotation specificity.

Picobubble enhanced fine coal flotation

Energy Technology Data Exchange (ETDEWEB)

Tao, Y.J.; Liu, J.T.; Yu, S.; Tao, D. [University of Kentucky, Lexington, KY (United States). Dept. of Mining Engineering

2006-07-01

Froth flotation is widely used in the coal industry to clean -28 mesh fine coal. A successful recovery of particles by flotation depends on efficient particle-bubble collision and attachment with minimal subsequent particle detachment from bubble. Flotation is effective in a narrow size range beyond which the flotation efficiency drops drastically. It is now known that the low flotation recovery of particles in the finest size fractions is mainly due to a low probability of bubble-particle collision while the main reason for poor coarse particle flotation recovery is the high probability of detachment. A fundamental analysis has shown that use of picobubbles can significantly improve the flotation recovery of particles in a wide range of size by increasing the probability of collision and attachment and reducing the probability of detachment. A specially designed column with a picobubble generator has been developed for enhanced recovery of fine coal particles. Picobubbles were produced based on the hydrodynamic cavitation principle. They are characterized by a size distribution that is mostly below 1 {mu}m and adhere preferentially to the hydrophobic surfaces. The presence of picobubbles increases the probability of collision and attachment and decreases the probability of detachment, thus enhancing flotation recovery. Experimental results with the Coalberg seam coal in West Virginia, U.S.A. have shown that the use of picobubbles in a 2 in. column flotation increased fine coal recovery by 10-30%, depending on the feed rate, collector dosage, and other flotation conditions. Picobubbles also acted as a secondary collector and reduced the collector dosage by one third to one half.

Fundamental Flotation Behaviors of Chalcopyrite and Galena Using O-Isopropyl-N-Ethyl Thionocarbamate as a Collector

Directory of Open Access Journals (Sweden)

Yongjie Bu

2018-03-01

Full Text Available Copper and lead are two important and widely used metals in industry. Chalcopyrite (CuFeS2 is associated with galena (PbS in ore, and it has been a research hotspot in separating galena from chalcopyrite by flotation. In this study, the flotation behaviors of chalcopyrite and galena were studied through flotation tests, adsorption measurements, solution chemistry calculation, Fourier transform infrared spectroscopy (FTIR and molecular dynamics (MD simulations. The results show that the floatability of chalcopyrite is better than that of galena in the presence of O-isopropyl-N-ethyl thionocarbamate (IPETC, and the recovery difference between chalcopyrite and galena is about 20% when IPETC is 7 × 10−4 mol/L at pH 9.5, while the floatability difference between the two minerals is significant. Competitive adsorption of OH− and IPETC on mineral surfaces leads to lower floatability of galena than that of chalcopyrite. IPETC is able to remove the hydration layer on mineral surfaces and then adsorb on active sites. The floatability of minerals is enhanced with the increase of their hydrophobicity. This study provides a reference to separate galena from chalcopyrite.

Fundamental properties of flotation frothers and their effect on flotation

Energy Technology Data Exchange (ETDEWEB)

Melo, F.; Laskowski, J.S. [University of British Columbia, Vancouver, BC (Canada). Dept. of Mining Engineering

2006-05-15

Froth flotation process requires the use of frothers. These important flotation agents are commonly characterized as either 'selective' or 'powerful' and are chosen following general guidelines and verification by laboratory and/or pilot plant tests. Fundamental properties of the flotation frothers have been extensively studied over the last few years. These studies have led to the development of standardised procedures to characterise frothers in terms of their ability to reduce bubble size and to increase foam stability. In this research project, the performance of five frothers in flotation of coal is evaluated and related to the fundamental properties of these agents. Since the recovery of water in the concentrate is closely related to the non-selective transport of solid particles by entrainment, the tested frothers are also assessed in terms of their ability to promote the transport of water towards the froth collection zone, both in absence and in presence of solids.

Vaal Reefs South uranium plant

International Nuclear Information System (INIS)

Anon.

1979-01-01

The Vaal Reefs mining complex, part of the Anglo American Corporation, is the largest gold and uranium producing complex in the world, being South Africa's principal producer, accounting for about a quarter of the country's uranium production. Vaal Reefs South uranium plant in the Orkney district was recently officially opened by Dr AJA Roux, the retiring president of the Atomic Energy Board and chairman of the Uranium Enrichment Corporation and will increase the country's uranium production. In the field of technology, and particularly processing technology, South Africa has shown the world unprecedented technology achievement in the field of uranium extraction from low grade ores and the development of the unique uranium enrichment process. New technical innovations that have been incorporated in this new plant are discussed

Quantitative property-property relationship (QPPR) approach in predicting flotation efficiency of chelating agents as mineral collectors.

Science.gov (United States)

Natarajan, R; Nirdosh, I; Venuvanalingam, P; Ramalingam, M

2002-07-01

The QPPR approach has been used to model cupferrons as mineral collectors. Separation efficiencies (Es) of these chelating agents have been correlated with property parameters namely, log P, log Koc, substituent-constant sigma, Mullikan and ESP derived charges using multiple regression analysis. Es of substituted-cupferrons in the flotation of a uranium ore could be predicted within experimental error either by log P or log Koc and an electronic parameter. However, when a halo, methoxy or phenyl substituent was in para to the chelating group, experimental Es was greater than the predicted values. Inclusion of a Boolean type indicative parameter improved significantly the predictability power. This approach has been extended to 2-aminothiophenols that were used to float a zinc ore and the correlations were found to be reasonably good.

Bibliometric analysis on kaolinite flotation

Directory of Open Access Journals (Sweden)

Gabriela Lieberknecht

Full Text Available Abstract The current work presents a bibliometric discussion on articles published worldwide concerning kaolinite flotation in international journals from 1992 to 2015. In total, 39 articles were selected from Elsevier's database, SciVerse ScienceDirect. This work allowed to recognize and identify which are the thematic and methodological trends that are being used, in addition to the main collectors used in kaolinite flotation. The results show that a significant amount of articles is produced by Chinese authors, especially from 2013, as China is the second highest aluminum producer in the world, and kaolinite is the reject in the reverse flotation process of diaspore. The results showed the difficulty of working with kaolinite flotation individually and confirmed that there is scientific collaboration among authors. Bibliometric analysis showed that the reagents used in kaolinite flotation tests are mostly derived from cationic nitrogenated compounds. Additionally, best recovery results from kaolinite flotation occurred in acidic media.

Studies on coal flotation in flotation column using statistical technique

Energy Technology Data Exchange (ETDEWEB)

M.S. Jena; S.K. Biswal; K.K. Rao; P.S.R. Reddy [Institute of Minerals & Materials Technology (IMMT), Orissa (India)

2009-07-01

Flotation of Indian high ash coking coal fines to obtain clean coal has been reported earlier by many authors. Here an attempt has been made to systematically analyse factors influencing the flotation process using statistical design of experiments technique. Studies carried out in a 100 mm diameter column using factorial design to establish weightage of factors such as feed rate, air rate and collector dosage indicated that all three parameters have equal influence on the flotation process. Subsequently RSM-CCD design was used to obtain best result and it is observed that 94% combustibles can be recovered with 82.5% weight recovery at 21.4% ash from a feed containing 31.3% ash content.

Development of copper recovery process from flotation tailings by a combined method of high‒pressure leaching‒solvent extraction.

Science.gov (United States)

Han, Baisui; Altansukh, Batnasan; Haga, Kazutoshi; Stevanović, Zoran; Jonović, Radojka; Avramović, Ljiljana; Urosević, Daniela; Takasaki, Yasushi; Masuda, Nobuyuki; Ishiyama, Daizo; Shibayama, Atsushi

2018-06-15

Sulfide copper mineral, typically Chalcopyrite (CuFeS 2 ), is one of the most common minerals for producing metallic copper via the pyrometallurgical process. Generally, flotation tailings are produced as a byproduct of flotation and still consist of un‒recovered copper. In addition, it is expected that more tailings will be produced in the coming years due to the increased exploration of low‒grade copper ores. Therefore, this research aims to develop a copper recovery process from flotation tailings using high‒pressure leaching (HPL) followed by solvent extraction. Over 94.4% copper was dissolved from the sample (CuFeS 2 as main copper mineral) by HPL in a H 2 O media in the presence of pyrite, whereas the iron was co‒dissolved with copper according to an equation given as C Cu  = 38.40 × C Fe . To avoid co‒dissolved iron giving a negative effect on the subsequent process of electrowinning, solvent extraction was conducted on the pregnant leach solution for improving copper concentration. The result showed that 91.3% copper was recovered in a stripped solution and 98.6% iron was removed under the optimal extraction conditions. As a result, 86.2% of copper was recovered from the concentrate of flotation tailings by a proposed HPL‒solvent extraction process. Copyright © 2018 Elsevier B.V. All rights reserved.

Coal flotation optimization using modified flotation parameters and combustible recovery in a Jameson cell

International Nuclear Information System (INIS)

Vapur, Hueseyin; Bayat, Oktay; Ucurum, Metin

2010-01-01

This study discusses a new coal flotation optimization approach. It is conducted using modified flotation parameters and combustible recovery. The experimental work was evaluated in two stages. In the first stage, recoveries (1, 2, 3, 5 and 8 min of flotation times) of Jameson flotation operating parameters were fitted to first-order kinetic model, R = R ∞ [1 - exp (-kt)] where R was recovery at t time, R ∞ was ultimate recovery and k was the first-order rate constant to draw the time recovery curves in the experimental study. Two parameters, the ultimate recovery (R ∞ ) and first-order rate constant (k), were then obtained from the model to fit an experimental time recovery curve. A modified flotation rate constant (K m ) defined as product of R ∞ and k, i.e., K m = R ∞ * k, and selectivity index (SI) defined as the ratio of the modified rate constant of coal to the modified rate constant of ash (SI)=K m of Coal/K m of Ash), which could be collectively called 'modified flotation parameters'. It was used to determine of the sub and upper values of operation variables. In the second one, combustible recovery (%) and ash content (%) were used to optimization of the Jameson flotation variables and it was found that d 80 = 0.250 mm particle size, 1/1 vegetable oil acids/kerosene ratio, 20% solids pulp density, 0.600 L/min wash water rate and 40 cm downcomer immersion dept could be used to separate efficiently coal from ash. Final concentrate was obtained with 94.83% combustible recovery and 17.86% ash content at optimum conditions after 8 min flotation time.

Adsorption of N-tallow 1,3-propanediamine-dioleate collector on albite and quartz minerals, and selective flotation of albite from greek stefania feldspar ore.

Science.gov (United States)

Vidyadhar, A; Hanumantha Rao, K; Forssberg, K S E

2002-04-01

The adsorption behavior of tallow 1,3-propanediamine-dioleate (Duomeen TDO) collector on albite and quartz minerals is assessed through Hallimond flotation, zeta potential, and diffuse reflectance FTIR investigations, together with the species distribution of the collector. The collector performance on albite separation from a natural feldspar material is evaluated in bench scale flotation tests. The Hallimond flotation responses of the minerals as a function of pH and collector concentration indicate that albite can be selectively floated from quartz at pH 2 where the doubly positively charged collector species adsorb on albite but not on quartz. However, the zeta potential and infrared spectra reveal that the adsorption behavior of the collector is similar on both minerals. The discrepancy in the flotation and adsorption results is attributed to the coarse and fine particle size fractions, and the shorter and longer equilibration periods employed in these studies respectively. The comparable adsorption on fine particles of albite and quartz at pH 2 is explained by the interaction of ammonium ions on silanol groups by hydrogen bonding as well as electrostatic interactions. The changes in zeta potentials are in good agreement with the formation of ionic species and free molecular forms of the collector. The IR spectra show the coexistence of neutral oleic acid together with charged amine species at low pH values in accordance with the species distribution diagram. Selective flotation of albite is accomplished from a natural feldspar material with tallow diamine-dioleate collector at pH 2 using sulfuric acid, only when the feed is deslimed prior to the bench scale flotation tests. An albite recovery exceeding 85% is achieved from a feed material containing about 50% albite.

Idea of Identification of Copper Ore with the Use of Process Analyser Technology Sensors

Science.gov (United States)

Jurdziak, Leszek; Kaszuba, Damian; Kawalec, Witold; Król, Robert

2016-10-01

The Polish resources of the copper ore exploited by the KGHM S.A. underground mines are considered as one of the most complex in the world and - consequently - the most difficult to be processed. The ore consists of three lithology forms: dolomites, shales and sandstones but in different proportions which has a significant impact on the effectiveness of the grinding and flotation processes. The lithological composition of the ore is generally recognised in-situ but after being mined it is blended on its long way from various mining fields to the processing plant by the complex transportation system consisting of belt conveyors with numerous switching points, ore bunkers and shafts. Identification of the lithological composition of the ore being supplied to the processing plant should improve the adjustments of the ore processing machinery equipment aiming to decrease the specific processing (mainly grinding) energy consumption as well as increase the metal recovery. The novel idea of Process Analyser Technology (PAT) sensors - information carrying pellets, dropped into the transported or processed bulk material which can be read directly when needed - is investigated for various applications within the DISIRE project (a part of the SPIRE initiative, acting under the Horizon2020 framework program) and here is adopted for implementing the annotation the transported copper ore for the needs of ore processing plants control. The identification of the lithological composition of ore blended on its way to the processing plant can be achieved by an information system consisting of pellets that keep the information about the original location of the portions of conveyed ore, the digital, geological database keeping the data of in-situ lithology and the simulation models of the transportation system, necessary to evaluate the composition of the blended ore. The assumptions of the proposed solution and the plan of necessary in-situ tests (with the special respect to harsh

Flotation of PAH contaminated dredged sludge

NARCIS (Netherlands)

Mulleneers, H.; Roubroeks, S.; Bruning, H.; Rulkens, W.H.; Koopal, L.K.

2000-01-01

The applicability of dissolved air flotation to remediate contaminated sediments of "Overschie" (Rotterdam) and "Petrol Harbor" (Amsterdam) is studied. Several flotation reagents (Diesel Fuel, Montanol, Aerophine, Aerofroth) are applied to enhance the flotation efficiency. The physical chemical

Beneficiation studies of an uranium siliceous - phosphate ore

International Nuclear Information System (INIS)

Bruno, J.B.; Santos, A.T.; Santos Benedetto, J. dos

1980-01-01

The consolidation of the beneficiation studies of a low-grade uranium siliceous - phosphate ore (11% P 2 O 5 ) from Itataia region in the Northeast of Brazil, owned by Empresas Nucleares Brasileiras S.A. - NUCLEBRAS, are presented. Laboratory studies using froth flotation technique and applying statistical methods for data evaluation were made. Pilot plant tests in a 120 Kg/h scale were conducted as a consequence of the bench scale tests. The developed process using tall-oil as collector and starch as depressant gave a total yield of 80% for the P 2 O 5 and 71% the U 3 O 8 , for a 33% P 2 O 5 phosphate concentrate. (Author) [pt

Picobubble column flotation of fine coal

Energy Technology Data Exchange (ETDEWEB)

Daniel Tao; Samuel Yu; Xiaohua Zhou; R.Q. Honaker; B.K. Parekh [University of Kentucky, Lexington, KY (United States). Department of Mining Engineering

2008-01-15

Froth flotation is widely used in the coal industry to clean -28 mesh (0.6 mm) or -100 mesh (0.15 mm) fine coal. A successful recovery of particles by flotation depends on efficient particle-bubble collision and attachment with minimal subsequent particle detachment from bubble. Flotation is effective in a narrow size range, nominally 10-100 {mu}m, beyond which the flotation efficiency drops sharply. A fundamental analysis has shown that use of picobubbles can significantly improve the flotation recovery of particles by increasing the probability of collision and attachment and reducing the probability of detachment. A specially designed column with a picobubble generator has been developed for enhanced recovery of fine coal particles. Picobubbles were produced based on the hydrodynamic cavitation principle. Experimental results have shown that the use of picobubbles in a 5-cm diameter column flotation increased the combustible recovery of a highly floatable coal by up to 10% and that of a poorly floatable coal by up to 40%, depending on the feed rate, collector dosage, and other flotation conditions. 14 refs.

Mathematical models of hydrocyclone performance in various copper ores preparation circuits

Directory of Open Access Journals (Sweden)

Niedoba Tomasz

2016-01-01

Full Text Available Copper ores located in the Lubin-Glogow Copper Basin contain three main lithological fractions: sandstone, carbonate and shale. This fact is the basic problem of organization and conducting ore preparation to flotation. The existing circuit of feed preparation contains (in ZG Rudna five classification nodes of hydrocyclones which fit for various purposes. The elaboration of concept of monitoring work of these nodes should be based on appropriate mathematical models of process. It was decided that either regressive or non-dimensional models that is classification according to Svarovsky, and particularly Plitt’s, will be suitable, in the aspects of d50 and partition sharpness. Errors resulting from determination of the features being part of the equations were also important. In this paper the errors were divided into technical and technological. The issue of experiments organization (mineralogical investigation connected with each classification node was also addressed. It is obvious that each classification node must obtain its characteristics because of various comminution products directed to classification.

Determination of flotation reagents used in tin-mining by capillary electrophoresis.

Science.gov (United States)

Hissner, F; Daus, B; Mattusch, J; Heinig, K

1999-08-20

Alkyl xanthates (O-alkyl dithiocarbonates) and phosphonates are important organic collectors for the flotation of metals from crude ore. Leaching from waste dumps into river and ground water, these substances can cause environmental pollution. A capillary electrophoretic method for the routine determination of ethyl, isopropyl, hexyl xanthate, and styrene phosphonate has been developed. Separation within 12 min could be achieved in borate pH 8.8 performing UV detection at 254 and 300 nm simultaneously. To improve the limits of detection obtained with hydrodynamic injection (0.4-1.5 ppm), field amplified sample injection (FASI) and stacking were investigated. An increase in sensitivity up to 4-8 fold could be achieved by pressure assisted FASI. Applying a stacking method to enrich the analytes by filling the capillary with sample solution to one third of its length, the limits of detection could be decreased to 10-40 ppb. Water samples from a former tin ore mining area have been analyzed using the optimized stacking technique. Quantitation was performed by standard addition. Good precision and accuracy were obtained, making this robust capillary electrophoretic method well-suited for routine analysis.

Effectiveness acidic pre-cleaning for copper-gold ore

Directory of Open Access Journals (Sweden)

Antonio Clareti Pereira

Full Text Available Abstract The presence of copper-bearing minerals is known to bring on many challenges during the cyanidation of gold ore, like high consumption of cyanide and low extraction of metal, which are undesirable impacts on the auriferous recovery in the subsequent process step. The high copper solubility in cyanide prevents the direct use of classical hydrometallurgical processes for the extraction of gold by cyanidation. Additionally, the application of a conventional flotation process to extract copper is further complicated when it is oxidized. As a result, an acid pre-leaching process was applied in order to clean the ore of these copper minerals that are cyanide consumers. The objective was to evaluate the amount of soluble copper in cyanide before and after acidic cleaning. From a gold ore containing copper, the study selected four samples containing 0.22%, 0.55%, 1.00% and 1.36% of copper. For direct cyanidation of the ore without pre-treatment, copper extraction by cyanide complexing ranged from 8 to 83%. In contrast, the pre-treatment carried out with sulfuric acid extracted 24% to 99% of initial copper and subsequent cyanidation extracted 0.13 to 1.54% of initial copper. The study also showed that the copper contained in the secondary minerals is more easily extracted by cyanide (83%, being followed by the copper oxy-hydroxide minerals (60%, while the copper contained in the manganese oxide is less complexed by cyanide (8% a 12%. It was possible to observe that minerals with low acid solubility also have low solubility in cyanide. Cyanide consumption decreased by about 2.5 times and gold recovery increased to above 94% after acidic pre-cleaning.

Flotation of Biological Materials

Directory of Open Access Journals (Sweden)

George Z. Kyzas

2014-03-01

Full Text Available Flotation constitutes a gravity separation process, which originated from the minerals processing field. However, it has, nowadays, found several other applications, as for example in the wastewater treatment field. Concerning the necessary bubble generation method, typically dispersed-air or dissolved-air flotation was mainly used. Various types of biological materials were tested and floated efficiently, such as bacteria, fungi, yeasts, activated sludge, grape stalks, etc. Innovative processes have been studied in our Laboratory, particularly for metal ions removal, involving the initial abstraction of heavy metal ions onto a sorbent (including a biosorbent: in the first, the application of a flotation stage followed for the efficient downstream separation of metal-laden particles. The ability of microorganisms to remove metal ions from dilute aqueous solutions (as most wastewaters are is a well-known property. The second separation process, also applied effectively, was a new hybrid cell of microfiltration combined with flotation. Sustainability in this field and its significance for the chemical and process industry is commented.

Determination of molybdenum in flotation concentrates by atomic absorption spectrophotometry

International Nuclear Information System (INIS)

Ise, Kazuo

1978-01-01

Molybdenum was determined by atomic absorption spectrophotometry in 0.05 N ammoniacal solution after the decomposition of the concentrate with aqua regia. Negros ore from Philippines was used as a flotation feed, which contained chalcopyrites and calcium-magnesium minerals. Among the metals tested copper, iron and the alkaline earths interfered. Less than 50 ppm of copper yielded lower results for molybdenum. Higher results came out with more than 50 ppm of copper. In the presence of iron and citric acid (0.4 g/100 ml) which is a suppressor for hydroxide formation, a lower estimation resulted for molybdenum. Calcium interfered, lower results by 2 and >10% being obtained with respective 2.5 and 20 ppm of calcium. More than 20 ppm of magnesium behaved similarly. Sodium sulfate (0.5 g/100 ml) served as the suppressor for copper, iron and citric acid; 100 ppm each of copper and iron did not interfere in this way. Interferences due to calcium and magnesium (less than 60 ppm) was able to be masked by the addition of sodium silicate (200 ppm as silica). The analysis of flotation products and synthetic samples consisting of molybdenite, chalcopyrite, calcium chloride and magnesium sulfate revealed that the atomic absorption method can be applied to the analysis of the concentrates for molybdenum with an error of about 2%. (auth.)

Waste water treatment by flotation

Directory of Open Access Journals (Sweden)

Camelia Badulescu

2005-11-01

Full Text Available The flotation is succesfully applied as a cleaning method of waste water refineries, textile fabrics (tissues, food industry, paper plants, oils plants, etc. In the flotation process with the released air, first of all, the water is saturated with air compressed at pressures between 0,3 – 3 bar, followed by the relaxed phenomenon of the air-water solution in a flotation cell with slowly flowing. The supersaturation could be applied in the waste water treatment. In this case the waste water, which is in the atmospheric equilibrum, is introduced in a closed space where the depression is 0,3 – 0,5 bar. Our paper presents the hypobaric flotation cell and the technological flow of cleaning of domestic waste waters

A new mathematical model for coal flotation kinetics

OpenAIRE

Guerrero-Pérez, Juan Sebastián; Barraza-Burgos, Juan Manuel

2017-01-01

Abstract This study describes the development and formulation of a novel mathematical model for coal flotation kinetic. The flotation rate was considered as a function of chemical, operating and petrographic parameters for a global flotation order n. The equation for flotation rate was obtained by dimensional analysis using the Rayleigh method. It shows the dependency of flotation kinetic on operating parameters, such as air velocity and particle size; chemical parameters, such as reagents do...

Thin-layer heap bioleaching of copper flotation tailings containing high levels of fine grains and microbial community succession analysis

Science.gov (United States)

Hao, Xiao-dong; Liang, Yi-li; Yin, Hua-qun; Liu, Hong-wei; Zeng, Wei-min; Liu, Xue-duan

2017-04-01

Thin-layer heap bioleaching of copper flotation tailings containing high levels of fine grains was carried out by mixed cultures on a small scale over a period of 210 d. Lump ores as a framework were loaded at the bottom of the ore heap. The overall copper leaching rates of tailings and lump ores were 57.10wt% and 65.52wt%, respectively. The dynamic shifts of microbial community structures about attached microorganisms were determined using the Illumina MiSeq sequencing platform based on 16S rRNA amplification strategy. The results indicated that chemolithotrophic genera Acidithiobacillus and Leptospirillum were always detected and dominated the microbial community in the initial and middle stages of the heap bioleaching process; both genera might be responsible for improving the copper extraction. However, Thermogymnomonas and Ferroplasma increased gradually in the final stage. Moreover, the effects of various physicochemical parameters and microbial community shifts on the leaching efficiency were further investigated and these associations provided some important clues for facilitating the effective application of bioleaching.

Long-Term Planning for Open Pits for Mining Sulphide-Oxide Ores in Order to Achieve Maximum Profit

Science.gov (United States)

Kržanović, Daniel; Conić, Vesna; Stevanović, Dejan; Kolonja, Božo; Vaduvesković, Jovan

2017-12-01

Profitable exploitation of mineralised material from the earth's crust is a complex and difficult task that depends on a comprehensive planning process. Answering the question of how to plan production depends on the geometry of the deposit, as well as the concentration, distribution, and type of minerals in it. The complex nature of mineral deposits largely determines the method of exploitation and profitability of mining operations. In addition to unit operating costs and metal prices, the optimal recovery of and achievement of maximum profit from deposits of sulphide-oxide ores also depend, to a significant extent, on the level of technological recovery achieved in the ore processing procedure. Therefore, in defining a long-term development strategy for open pits, special attention must be paid to the selection of an optimal procedure for ore processing in order to achieve the main objective: maximising the Net Present Value (NPV). The effect of using two different processes, flotation processing and hydrometallurgical methods (bioleaching acid leaching), on determining the ultimate pit is shown in the case of the Kraku Bugaresku-Cementacija sulphide-oxide ore deposit in eastern Serbia. Analysis shows that the application of hydrometallurgical methods of processing sulphide-oxide ore achieved an increase in NPV of 20.42%.

Selective flotation of phosphate minerals with hydroxamate collectors

Science.gov (United States)

Miller, Jan D.; Wang, Xuming; Li, Minhua

2002-01-01

A method is disclosed for separating phosphate minerals from a mineral mixture, particularly from high-dolomite containing phosphate ores. The method involves conditioning the mineral mixture by contacting in an aqueous in environment with a collector in an amount sufficient for promoting flotation of phosphate minerals. The collector is a hydroxamate compound of the formula; ##STR1## wherein R is generally hydrophobic and chosen such that the collector has solubility or dispersion properties it can be distributed in the mineral mixture, typically an alkyl, aryl, or alkylaryl group having 6 to 18 carbon atoms. M is a cation, typically hydrogen, an alkali metal or an alkaline earth metal. Preferably, the collector also comprises an alcohol of the formula, R'--OH wherein R' is generally hydrophobic and chosen such that the collector has solubility or dispersion properties so that it can be distributed in the mineral mixture, typically an alkyl, aryl, or alkylaryl group having 6 to 18 carbon atoms.

Surface chemical problems in coal flotation

Science.gov (United States)

Taylor, S. R.; Miller, K. J.; Deurbrouck, A. W.

1981-02-01

As the use of coal increases and more fine material is produced by mining and processing, the need for improved methods of coal beneficiation increases. While flotation techniques can help meet these needs, the technique is beset with many problems. These problems involve surface chemical and interfacial properties of the coal-mineral-water slurry systems used in coal flotation. The problems associated with coal flotation include non-selectivity, inefficient reagent utilization, and excessive variablity of results. These problems can be broadely classified as a lack of predictability. The present knowledge of coal flotation is not sufficient, in terms of surface chemical parameters, to allow prediction of the flotation response of a given coal. In this paper, some of the surface chemical properties of coal and coal minerals that need to be defined will be discussed in terms of the problems noted above and their impact on coal cleaning.

New directions in flotation machine design

Energy Technology Data Exchange (ETDEWEB)

Jameson, G.J. [University of Newcastle, Callaghan, NSW (Australia)

2010-10-15

The theoretical background for flotation kinetics of ultrafine and coarse particles are explored. Recent advances in flotation technology for these difficult areas are reviewed, with a focus on improving the flotation rate of ultrafines, and extending the upper limit for coarse particle flotation. For ultra-fine particles, the theory suggests that the rate of flotation can be improved by increasing the rate of shear in the suspension of particles and bubbles. A new cell has been developed, the Concorde Cell, in which the pre-aerated feed is raised to supersonic velocities before passing into a high-shear zone in the flotation cell. The local dissipation rate is of the order of 100 kW/m{sup 3}, one to two orders of magnitude higher than is available in conventional mechanical cells. The Concorde Cell has been trialed on a finely ground PGM feed in South Africa, with excellent results. By recycling the tailings, and using the mass pull or solids recovery as the control variable, the Cell is capable of producing a high-grade concentrate at high recoveries, over a wide range of particle sizes. Theory for the upper limit of coarse particle flotation suggests that a quiescent flow field is necessary to prevent the particles from becoming detached from the bubbles. A liquid-fluidized bed provides a suitable environment. The flotation feed is introduced into the fluidized bed, and air bubbles are dispersed in the fluidizing water. Coarse particles attach to the bubbles rising through the bed and are lifted into the froth layer that is maintained on top of the cell in the usual way. Particles of galena up to 1 mm in diameter have been recovered in such a bed, while for particles of lower density such as quartz and coal, the upper limit for flotation has been extended to at least 2 mm and 5.6 mm respectively. The fluidized bed technology provides major advantages beyond the ability to recover coarse particles currently lost in existing operations.

Further Investigations on Simultaneous Ultrasonic Coal Flotation

Directory of Open Access Journals (Sweden)

Safak Gokhan Ozkan

2017-09-01

Full Text Available This study investigates the flotation performance of a representative hard coal slime sample (d80 particle size of minus 0.2 mm obtained from the Prosper-Haniel coal preparation plant located in Bottrop, Germany. Flotation was carried out with a newly designed flotation cell refurbished from an old ultrasonic cleaning bath (2.5 L volume equipped with a single frequency (35 kHz and two different power levels (80–160 W and a sub-aeration-type flotation machine operating at a stable impeller speed (1200 rpm and air rate (2.5 L/min. The reagent combination for conventional and simultaneous ultrasonic coal flotation tests was Ekofol-440 at variable dosages (40–300 g/t with controlling water temperature (20–25 °C at natural pH (6.5–7.0. The batch coal flotation results were analyzed by comparing the combustible recovery (% and separation efficiency (% values, taking mass yield and ash concentrations of the froths and tailings into account. It was found that simultaneous ultrasonic coal flotation increased yield and recovery values of the floated products with lower ash values than the conventional flotation despite using similar reagent dosages. Furthermore, particle size distribution of the ultrasonically treated and untreated coals was measured. Finely distributed coal particles seemed to be agglomerated during the ultrasonic treatment, while ash-forming slimes were removed by hydrodynamic cavitation.

Flotation extraction of tributyl phosphate from s olutions

International Nuclear Information System (INIS)

Skrylev, L.D.; Tkachenko, N.V.; Sazonova, V.F.

1983-01-01

Results of investigations, conducted for revealing the possibility of flotation extraction of emulsificated and actually dissolved extractants, tributyl phosphate (TBP) in particular, are given. The possibility of flotation extraction of emulsificated and actually dissolved TBP by its non-reagent flotation was established experimeptally. It was also established that the kinetics of flotation TBP extraction is described by the equation, similar to the reaction equation of the first order. The process of non-reagent TBP flotation proceeds most successfully in pH=6.5-7.5 range

Pyrolitics Oils in Coal Flotation

Czech Academy of Sciences Publication Activity Database

Čáblík, V.; Išek, J.; Herková, M.; Halas, J.; Čáblíková, L.; Vaculíková, Lenka

2014-01-01

Roč. 34, č. 2 (2014), s. 9-14 ISSN 1640-4920 Institutional support: RVO:68145535 Keywords : pyrolytic oils * flotation, black coal * new flotation reagents Subject RIV: CB - Analytical Chemistry, Separation http://homen.vsb.cz/hgf/546/IM_2014_02.pdf

Studies on the recovery of uranium from low-grade ores in India

International Nuclear Information System (INIS)

Jayaram, K.M.V.; Dwivedy, K.K.; Deshpande, A.S.; Ramachar, T.M.

1976-01-01

Investigations were carried out to utilize the available para-marginal and low-grade ores - chlorite schists, amphibolites, carbonate ores, clays and quartzites - analysing between 0.027 and 0.08% U 3 O 8 . In addition, tests were undertaken on the technical and economic feasibility of recovering uranium as a byproduct from the copper flotation tailings and phosphorites. Heap and bacterial leaching tests were conducted on quartz-chlorite schists from the Singhbhum district, Bihar, analysing about 0.03% U 3 O 8 . Studies also showed that the ores harbour active Ferrobacillus ferrooxidans. Studies on 10-mesh samples of amphibolites from Inderwa, Bihar, (0.08% U 3 O 8 ) showed that only 32.8% recovery could be obtained by wet tabling and 85% by agitation leaching, while static leaching tests yielded 81% recovery in 24 hours of contact time. Similar tests on calcareous phyllites (0.05% U 3 O 8 ) with 30 kg/t Na 2 CO 3 and 8 kg/t NaHCO 3 yielded 86% uranium leachability at ambient temperature. Biogenic uraniferous clay from Udaisagar (0.029% U 3 O 8 ) yielded 43.3% uranium recovery using 1000 l/t of neutral water for 6 h. Percolation leaching tests were conducted with hard quartzites (0.06% U 3 O 8 ), and the results showed that 81% uranium could be recovered in 24 days. Although preliminary ore dressing studies on tailings obtained from the copper flotation (0.013% U 3 O 8 ) at Surda yielded a concentrate analysing 0.063% U 3 O 8 at 66% recovery, recent tests on the tailings from the copper concentrator indicated only 48% recovery at a grade of 0.112% owing to decrease in the feed grade. Studies on the utilization of large-capacity gravity machines and selective mining of uranium-rich copper lodes may render this source economic. Preliminary studies on a phosphorite sample containing 22.0% P 2 O 5 and 0.04% U 3 O 8 from the Mussorie area in Uttar Pradesh on calcination followed by scrubbing yielded a sand enriched in P 2 O 5 values (33.7% P 2 O 5 at 92.5% recovery) but

Separation of oily materials in radioactive waste waters by flotation. Flotation kinetics

International Nuclear Information System (INIS)

Flores E, R.M.; Ortiz O, H.B.

2003-01-01

The rate of separation of oil and total cobalt in the oleaginous residual water previously treated by coagulation/flocculation with a quaternary ammonium amine (25 mgL -1 ) and with modified anionic polyacrylamide (1.5 mgL -1 ) (pH = 7, G 1 = 300 s -1 and G 2 = 30 s -1 ) was determined. The experimental essays to determine the flotation kinetics, its were carried out using as operation and control parameters the air/solids relationship (G/S 0.35), pressure (P =620 kPa) and volume of air-water mixture (V = 37% of V f ), obtained in previous essays, at two different pressure levels and volume of discharged mixture. The kinetic studies of flotation obtained for the flotation system with conventional air dissolved (DAF) its suggest a first order kinetics that it can be represented by the SCC model. At the same time its show that the separation of the present pollutants in the residual water is governed by the removal velocity of the oil. Meanwhile, the concentration of total Co below 1 mgL -1 , on the other hand, the concentration of the 60 Co at the end of the flotation process resulted smaller than 0.008 Bq/ml, as long as the one 54 Mn were not detectable. (Author)

Mechanisms of beryl flotation: a literature review

International Nuclear Information System (INIS)

Torem, M.L.

1988-01-01

This paper shows a review about the investigations that have been done on the mechanisms of flotation of beryl and its dependence in relation to the presence of fluoride species. It is also analised the anionic flotation of the mineral and the effect of cations in the pulp of flotation. (author) [pt

Optimization of Cu-Zn Massive Sulphide Flotation by Selective Reagents

Science.gov (United States)

Soltani, F.; Koleini, S. M. J.; Abdollahy, M.

2014-10-01

Selective floatation of base metal sulphide minerals can be achieved by using selective reagents. Sequential floatation of chalcopyrite-sphalerite from Taknar (Iran) massive sulphide ore with 3.5 % Zn and 1.26 % Cu was studied. D-optimal design of response surface methodology was used. Four mixed collector types (Aer238 + SIPX, Aero3477 + SIPX, TC1000 + SIPX and X231 + SIPX), two depressant systems (CuCN-ZnSO4 and dextrin-ZnSO4), pH and ZnSO4 dosage were considered as operational factors in the first stage of flotation. Different conditions of pH, CuSO4 dosage and SIPX dosage were studied for sphalerite flotation from first stage tailings. Aero238 + SIPX induced better selectivity for chalcopyrite against pyrite and sphalerite. Dextrin-ZnSO4 was as effective as CuCN-ZnSO4 in sphalerite-pyrite depression. Under optimum conditions, Cu recovery, Zn recovery and pyrite content in Cu concentrate were 88.99, 33.49 and 1.34 % by using Aero238 + SIPX as mixed collector, CuCN-ZnSO4 as depressant system, at ZnSO4 dosage of 200 g/t and pH 10.54. When CuCN was used at the first stage, CuSO4 consumption increased and Zn recovery decreased during the second stage. Maximum Zn recovery was 72.19 % by using 343.66 g/t of CuSO4, 22.22 g/t of SIPX and pH 9.99 at the second stage.

New insights into the oleate flotation response of feldspar particles of different sizes: Anisotropic adsorption model.

Science.gov (United States)

Xu, Longhua; Tian, Jia; Wu, Houqin; Deng, Wei; Yang, Yaohui; Sun, Wei; Gao, Zhiyong; Hu, Yuehua

2017-11-01

The anisotropic adsorption of sodium oleate (NaOL) on feldspar surfaces was investigated to elucidate the different flotation properties of feldspar particles of four different size ranges. Microflotation experiments showed that the feldspar flotation recovery of particles with sizes spanning different ranges decreased in the order 0-19>19-38>45-75>38-45μm. Zeta potential and FTIR measurements showed that NaOL was chemically adsorbed on the Al sites of the feldspar surface. The anisotropic surface energies and broken bond densities estimated by density functional theory calculations showed that, although feldspar mostly exposed (010) and (001) surfaces, only the (001) surfaces contained the Al sites needed for NaOL adsorption. The interaction energies calculated by molecular dynamics simulations confirmed the more favorable NaOL adsorption on (001) than (010) surfaces, which may represent the main cause for the anisotropic NaOL adsorption on feldspar particles of different sizes. SEM measurements showed that the main exposed surfaces on coarse and fine feldspar particles were the side (010) and basal (001) ones, respectively. A higher fraction of Al-rich (001) surfaces is exposed on fine feldspar particles, resulting in better floatability compared with coarse particles. XPS and adsorption measurements confirmed that the Al content on the feldspar surface varied with the particle size, explaining the different NaOL flotation of feldspar particles of different sizes. Therefore, the present results suggest that coarsely ground ore should be used for the separation of feldspar gangue minerals. Further improvements in the flotation separation of feldspar from associated valuable minerals can be achieved through selective comminution or grinding processes favoring the exposure of (010) surfaces. Copyright © 2017 Elsevier Inc. All rights reserved.

Flotation of sulphide minerals 1990

Energy Technology Data Exchange (ETDEWEB)

Forssberg, K S.E. [ed.; Luleaa University of Technology, Luleaa (Sweden). Division of Mineral Processing

1991-01-01

A total of 27 papers presented at the workshop on flotation of sulphide minerals, reprinted from the International Journal of Mineral Processing, vol. 33, nos. 1-4, are included in this book. They cover various aspects of flotation of such minerals as chalcopyrite, pyrrhotite, galena, malachite and pyrite.

Physically absorbable reagents-collectors in elementary flotation

Energy Technology Data Exchange (ETDEWEB)

S.A. Kondrat' ev; I.G. Bochkarev [Russian Academy of Sciences, Novosibirsk (Russian Federation). Institute of Mining

2007-09-15

Based on the reviewed researches held at the Institute of Mining, Siberian Branch, Russian Academy of Sciences, the effect of physically absorbable reagents-collectors on formation of a flotation complex and its stability in turbulent pulp flows in flotation machines of basic types is considered. The basic requirements for physically absorbable reagents-collectors at different flotation stages are established.

Effect of flotation on preparation of coal-water slurries

Energy Technology Data Exchange (ETDEWEB)

Ding, K.; Laskowski, J.S. [University of British Columbia, Vancouver, BC (Canada)

2009-07-01

In order to study the effect of flotation reagents on the properties of coal-water slurry, a sub-bituminous coal was cleaned via either forward flotation or reverse flotation. The froth product from the forward flotation, obtained with the use of diesel oil and MIBC, and the tailings of the reverse flotation, carried out with dextrin-tannic acid depressants and dodecyltrimethylammonium chloride collector, were used in the preparation of coal-water slurries. It was shown that while it was possible to obtain the coal-water slurry with a high-solids content from the coal rendered hydrophilic (tailings from the coal reverse flotation), in the case of the hydrophobic product (froth product from the forward flotation) a dispersing agent was required to obtain the coal-water slurry of the same high-solids content.

Influence of rotor circumference speed on flotation cell aeration

Energy Technology Data Exchange (ETDEWEB)

Dedek, F; Bortlik, V

1978-01-01

Laboratory test results of flotation experiments conducted in Czechoslovakia with the use of coal flotation particles <0.5 mm are presented. Three different cells and rotors were used, type MS, Denver, VRF 2 with various rotor diameters ranging from 40 mm to 95 mm. Nine tables show the results with varying flotation time, circumferenial velocity, flotation reagents and aeration. Test procedures are discussed; main results are that circumferenial velocity cannot be used as a decisive parameter for cell aeration and flotation efficiency, and that a direct transfer of parameters cannot be made to flotation cells with a different design and to larger industrial equipment. (4 refs.) (In German)

TEXTURAL DESCRIPTORS FOR MULTIPHASIC ORE PARTICLES

Directory of Open Access Journals (Sweden)

Laura Pérez-Barnuevo

2012-11-01

Full Text Available Monitoring of mineral processing circuits by means of particle liberation analysis through quantitative image analysis has become a routine technique within the last decades. Usually, liberation indices are computed as weight proportions, which is not informative enough when complex texture ores are treated by flotation. In these cases, liberation has to be computed as phase surface exposed to reactants, and textural relationships between minerals have to be characterized to determine the possibility of increasing exposure. In this paper, some indices to achieve a complete texture characterization have been developed in terms of 2D phase contact and mineral surfaces exposure. Indices suggested by other authors are also compared. The response of this set of parameters against textural changes has been explored on simple synthetic textures ranging from single to multiple inclusions and single to multiple veins and their ability to discriminate between different textural features is analyzed over real mineral particles with known internal structure.

Uranium-thorium silicates, with specific reference to the species in the Witwatersrand reefs

International Nuclear Information System (INIS)

Smits, G.

1987-01-01

(U,Th)-silicates form two complete series of anhydrous and hydrated species with general formulae (U,Th)SiO 4 and (U,Th)SiO 4 .nH 2 O respectively. The end-members of the anhydrous series are anhydrous coffinite and thorite, and those of the hydrated series, coffinite and thorogummite. Although the silicates are relatively rare in nature, coffinite is a common ore mineral in uranium deposits of the sandstone type. In the Witwatersrand reefs, (U,Th)-silicates are extremely rare in most reefs, except for the Elsburg Reefs on the West Rand Goldfield and the Dominion Reef. In these reefs detrital uraninite has been partly or entirely transformed to (U,Th)-silicates of coffinite composition, but thorite and thorogummite of detrital origin are also found in the Dominion Reef. In leaching tests on polished sections of rock samples containing (U,Th)-silicates, a dilute sulphuric acid solution, to which ferric iron had been added, was used as the lixiviant. It appeared that the dissolution of coffinite is less rapid than that of uraninite and uraniferous leucoxene. However, the reaction of silicates of high thorium content is much slower, and was not completed during the tests

Desulphurization of coal: bioleaching versus bioconditioning and flotation

Energy Technology Data Exchange (ETDEWEB)

M. Zeki Dogan; Gulhan Ozbayoglu [Istanbul Technical University, Istanbul (Turkey). Faculty of Mining

2007-07-01

There are two bio-desulphurization methods for the removal of pyritic sulphur, namely, bacterial leaching and bacterial conditioning for pyrite depression followed by flotation of coal. Bacterial leaching is a slow process, consequently, microbial desulphurization is focused on conditioning coal by bacteria for a short time, followed by flotation. The application of Acidithiobacillus ferrooxidans in bioconditioning followed by flotation process help the oxidation of pyrite surface and enhance its depression during the flotation of coal. By bacterial conditioning for 4 hours followed by flotation, almost 78 % pyritic sulphur removal was attained with the yield of 78 % in the floated coal, whereas bacterial leaching resulted in pyritic sulphur removal of 56.60 % in 10 days. 17 refs., 5 tabs.

Removal of Cobalt Ions by Precipitate Foam Flotation

Energy Technology Data Exchange (ETDEWEB)

Jung, In Ha; Lee, Jung Won [Korea Atomic Energy Research Institute, Taejon (Korea)

1998-09-30

Simulated waste liquid containing 50 ppm cobalt ion was tested by precipitate flotation using a sodium lauryl sulfate as a collector. The effects of initial cobalt ion concentration, pH, surfactant concentration, flotation time, gas flow rate and foreign ions on removal efficiency of cobalt ion were studied. Pretreatment of the waste liquid with 35% H{sub 2}O{sub 2} prior to precipitate flotation made shift of optimal flotation pH from the strong alkalinity to weak alkaline range and made a favorable flotation of cobalt ion in wide range of pH. For the result of this experiment, 99.8% removal efficiency was obtained on the conditions of initial cobalt ion concentration 50 ppm, pH 9.5, gas flow rate 70 ml/min, flotation time 30 min. The simulate ion was formed to be the most harmful ion against removal of cobalt by precipitate flotation of the species which were tested. The presence of 0.1 M of SO{sub 4}{sup 2-} ion decreased removal efficiency of cobalt to 90% while the cobalt were almost entirely removed in the absence of sulfate ion. (author). 11 refs., 8 figs.

On the hydrodynamics and the scale-up of flotation processes

International Nuclear Information System (INIS)

Schubert, H.

1986-01-01

In flotation machines, turbulence is process-determining. Macroturbulence is necessary for suspension, microturbulence controls the air dispersion, the rate of the particle-bubble collisions and the stresses on agglomerates. Consequently, the hydrodynamic optimization of flotation processes plays an important role for the flotation efficiency. In the paper the following aspects are considered: the turbulent microprocesses of flotation processes; the integral hydrodynamic characterization of flotation processes; correlations between particle size and optimum hydrodynamics; correlations between flocculation of fine particles and optimum-hydrodynamics; and hydrodynamic scale-up of flotation processes

Coal flotation technical review

Energy Technology Data Exchange (ETDEWEB)

Heiser, N. [C. Clarkson & Associates Pty. Ltd., Brisbane, Qld. (Australia)

1996-10-01

The Australian Coal Association Research Program (ACARP) recently commissioned a study into the status of flotation in coal preparation, in order to direct limited funds to areas of maximum benefit. The primary purpose of the study was the assessment of new flotation technologies, including those commercially available and those still under development. Technologies examined included: the Jameson Cell, Microcel, and Ekof cell. Problems and advantages are discussed, with suggestions for future areas of research. 3 figs.

Classification of Flotation Frothers

Directory of Open Access Journals (Sweden)

Jan Drzymala

2018-02-01

Full Text Available In this paper, a scheme of flotation frothers classification is presented. The scheme first indicates the physical system in which a frother is present and four of them i.e., pure state, aqueous solution, aqueous solution/gas system and aqueous solution/gas/solid system are distinguished. As a result, there are numerous classifications of flotation frothers. The classifications can be organized into a scheme described in detail in this paper. The frother can be present in one of four physical systems, that is pure state, aqueous solution, aqueous solution/gas and aqueous solution/gas/solid system. It results from the paper that a meaningful classification of frothers relies on choosing the physical system and next feature, trend, parameter or parameters according to which the classification is performed. The proposed classification can play a useful role in characterizing and evaluation of flotation frothers.

Atmospheric pollution with copper around the copper mine and flotation, 'Buchim', Republic of Macedonia, using biomonitoring moss and lichen technique

International Nuclear Information System (INIS)

Balabanova, Biljana; Bacheva, Katerina; Shajn, Robert; Stafilov, Trajche

2009-01-01

This paper has studied the atmospheric pollution with copper due to copper mining and flotation 'Buchim' near Radovish, Republic of Macedonia. The copper ore and ore tailings continually are exposed to open air, which occur winds carry out the fine particles in to atmosphere. Moss (Hyloconium splendens and Pleurozium schrebery) and lichen (Hypogymnia physodes and Parmelia sulcata) samples were used for biomonitoring the possible atmospheric pollution with copper in the mine vicinity. Moss and lichen samples were digested by using of microwave digestion system and copper was analyzed by atomic emission spectrometry with inductively coupled plasma (ICPAES). The obtained values for the content of copper in moss and lichen samples were statistically processed using the nonparametric and parametric analysis. Maps of areal deposition of copper show an increase content of copper in the vicinity of mine, but long distance distribution of this element is not established yet.

Two cases of physical treatment of uranium ore; Deux cas de traitement physique de minerai d'uranium

Energy Technology Data Exchange (ETDEWEB)

Ginocchio, A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

Until now, all uranium deposits exploited in France are vein type and present a very big variety of mineralization and structure. The process of concentration of these ores requires a study for each of them and, in a lot of cases, only the chemical attack can solve the problem. However, the flotation succeeded to results permitting a very interesting enrichment with lower investments expenses and cost prices. Enrichment by flotation would be foreseeable for poor layers and weak tonnage, permitting to absorb facilities on tonnages three times less important than the acidic treatment, or, to equality of cost price, to treat ores having contents of 2,5 to 4 times weaker. (M.B.) [French] Jusqu'ici, tous les gisements uraniferes exploites en France sont du type filonien et presentent une tres grande variete de mineralisation et de structure. Le procede de concentration de ces minerais necessite une etude pour chacun d'eux et, dans bien des cas, seule l'attaque chimique peut resoudre le probleme. Toutefois, la flottation a abouti a des resultats permettant un enrichissement tres interessant avec les depenses d'investissements et des prix de revient beaucoup plus bas. Un enrichissement par flottation serait envisageable pour des gisements pauvres et de faible tonnage, permettant d'amortir les installations sur des tonnages trois fois moins importants que le traitement acide, ou encore, a egalite de prix de revient, de traiter des minerais ayant des teneurs de 2,5 a 4 fois plus faibles. (M.B.)

Froth flotation of xenotime

Science.gov (United States)

Zhang, Yicheng

Froth flotation as a fundamental method for processing complex minerals is commonly applied to the surface chemistry and beneficiation of rare-earth-bearing minerals. This is due to the fact that it is possible to process a wide range of fine particle sizes and the process can be tailored to the unique mineralogy of a given deposit. Flotation effectiveness is primarily controlled by the surface-chemical properties of the minerals and related adsorption phenomena at the liquid--solid interface. This research program was designed to investigate the principles of surface chemistry and froth flotation of xenotime and selected gangue minerals. This led to a better understanding of the factors affecting flotation performance and separation of xenotime from associated gangue minerals in an efficient way. This investigation includes MLA analysis, surface area measurement, zeta potential tests, and adsorption tests of xenotime, ilmenite, zircon, schorl, and staurolite under conditions of various reagent additions and different temperatures. Octano-hydroxamic acid, sodium oleate, sodium silicates, and ammonium lignosulfonate were used in microflotation behavior evaluation. Efforts were made to evaluate the effects of temperature, pH, concentration, addition order, and depressants in the microflotation of minerals with anionic collectors such as octano-hydroxamic acid and sodium oleate. Other factors, such as bubble surface tension and bubble particle size, are also discussed based on the literature review and lab observations.

Flotation process diagnostics and modelling by coal grain analysis

Energy Technology Data Exchange (ETDEWEB)

Ofori, P; O' Brien, G.; Firth, B.; Jenkins, B. [CSIRO Energy Technology, Brisbane, Qld. (Australia)

2006-05-15

In coal flotation, particles of different components of the coal such as maceral groups and mineral matter and their associations have different hydrophobicities and therefore different flotation responses. By using a new coal grain analysis method for characterising individual grains, more detailed flotation performance analysis and modelling approaches have been developed. The method involves the use of microscopic imaging techniques to obtain estimates of size, compositional and density information on individual grains of fine coal. The density and composition partitioning of coal processed through different flotation systems provides an avenue to pinpoint the actual cause of poor process performance so that corrective action may be initiated. The information on grain size, density and composition is being used as input data to develop more detailed flotation process models to provide better predictions of process performance for both mechanical and column flotation devices. A number of approaches may be taken to flotation modelling such as the probability approach and the kinetic model approach or a combination of the two. In the work reported here, a simple probability approach has been taken, which will be further refined in due course. The use of grain data to map the responses of different types of coal grains through various fine coal cleaning processes provided a more advanced diagnostic capability for fine coal cleaning circuits. This enabled flotation performance curves analogous to partition curves for density separators to be produced for flotation devices.

Application of Acidithiobacillus Ferrooxidans in coal flotation

Energy Technology Data Exchange (ETDEWEB)

Amini, E.; Hosseini, T.R.; Oliazadeh, M.; Kolahdoozan, M. [University of Queensland, Brisbane, Qld. (Australia)

2009-07-01

Bioflotation is a potential method for removing pyritic sulphur from coal. Sodium cyanide is a well-known depressant for pyrite in flotation of sulphide minerals; however, for coal this reagent is unacceptable from the environmental point of view. This study investigates an alternate to sodium cyanide, Acidithiobacillus Ferrooxidans, a nonharmful bacterial reagent as a pyrite depressant. The flotation behavior of pyrite and other gangue particles using the sodium cyanide and the Ferrooxidans is compared by applying the general first-order flotation model. The kinetic parameters extracted from the model demonstrated that the modified flotation rate of pyrite was reduced, and the selectivity between coal and gangue was improved using the bacteria. These results indicate that Acidithiobacillus Ferrooxidans has potential in removing pyritic sulfur from coal.

Development of zero conditioning procedure for coal reverse flotation

Energy Technology Data Exchange (ETDEWEB)

D.P. Patil; J.S. Laskowski [University of British Columbia, Vancouver, BC (Canada). Mining Engineering Department

2008-04-15

The zero conditioning method was developed to facilitate the flotation of gangue minerals in the reverse coal flotation process. Batch and continuous methods were developed to maintain the zero conditioning principle during reverse flotation. Batch zero conditioning was achieved by adding the required amount of DTAB in one step, as soon as the air was introduced into the system. The continuous zero conditioning method involves uninterrupted addition of DTAB through a specially built sparger in the form of aerosol during the flotation experiment. This produces active bubbles that carry collector. The addition of DTAB in the form of aerosol during reverse flotation proved to be better in reducing the ash of a sub-bituminous (LS-26) coal from 34.7% to 22.9% with a froth product (gangue) yield of 36.8% without any depressant. In the presence of coal depressant (dextrin, 0.5 kg/t), the ash content of LS-26 coal was reduced from 34.7% to 16.5% at a clean coal yield of 55%, whereas the conventional (forward) flotation with fuel oil provided a clean coal containing 16.5% ash with only 29.2% yield. These results prove that flotation of gangue minerals is very much improved by maintaining zero conditioning time conditions in a coal reverse flotation process.

Application of flotational reagents obtained from coke-industry byproducts

Energy Technology Data Exchange (ETDEWEB)

N.I. Nikitin; I.N. Nikitin; N.I. Toporkova [Khar' kov Polytechnic Institute (Ukraine)

2007-06-15

Today, the operational efficiency of coal-preparation shops at coke plants largely depends on the flotation process, since flotation is the basic method of regenerating the slurry water in the water-slurry systems and the basic enrichment process for small-grain coal slurries. At The Coal-Chemistry Institute, attempts have been made to address the growing demand for readily available and relatively inexpensive flotational reagents. In particular, a list of promising coke-industry byproducts for use as flotational reagents has been compiled, and the possibility of reducing their toxicity has been established. In addition, various industrial byproducts and wastes have been investigated in terms of flotational activity.

Evaluation of column flotation results with a film flotation method; Film fusenho wo mochiita column fusen kekkan no hyoka

Energy Technology Data Exchange (ETDEWEB)

Fujimoto, H.; Matsukata, M.; Ueyama, K. [Osaka University, Osaka (Japan). Faculty of Engineering Science

1996-10-28

Change in wettability of coal particle surfaces due to kerosene adsorption was studied by using a film flotation method. The applicability of a film flotation method to coals modified by kerosene adsorption was first confirmed. In experiment, film flotation was applied to Illinois coal modified by aqueous methanol solution and kerosene adsorption, and the weight percent of residual particles on a gas-liquid interface and kerosene in aqueous methanol solution were analyzed to verify the applicability of a film flotation method. Film flotation was applied to Datong and Illinois coals modified by kerosene adsorption, and the weight percent of residual particles on a gas-liquid interface was plotted to surface tension of liquid. As a result, the weight percent of hydrophobic particles within 50mN/m in surface tension slightly increased in Datong coal and remarkably increased in Illinois coal with kerosene addition. It was thus suggested that in addition to surface tension, the distributions of hydrophilic and hydrophobic strengths on the surface of each coal particle should be considered to understand attachment of coal particles and bubbles. 6 refs., 4 figs.

Treatment of tailings water from uranium ore processing by reverse osmosis

International Nuclear Information System (INIS)

Georgescu, D.P.; Andrei, L.

2000-01-01

Mining and metallurgical waste waters are considered to be the major sources of heavy metal contamination. The need of economic and effective methods for metals removal have resulted in the development of new separation technologies. Precipitation, ion exchange, electrochemical processes, filtration and flotation are commonly applied for industrial effluents treatment. Occasionally, the application of such processes is limited because of technical or economical constraints. The search for new technologies regarding the recovery and removal of toxic metals from waste waters has directed attention to membrane processes. These processes are developed in the recent years due to the availability of many new types of membranes. This paper presents the laboratory test results for liquid radioactive effluent treatment from alkaline uranium ore processing by reverse osmosis. (author)

Improvement of the Separation Efficiency of Ion Flotation and Adsorbing Colloid Flotation by the Synergistic Effect of Mixed Surfactant Solutions

Energy Technology Data Exchange (ETDEWEB)

Kim, K.H.; Seo, E.J.; Choi, S.J. [Dept. of. Env. Eng., Kyungpook National University, Taegu (Korea)

1999-02-01

Experimental investigations on the removal of Cd(II) from aqueous ablution were carried out through two foam separation techniques : ion floatation and adsorbing colloid flotation with Fe(III). The optimum pH for good removal was found to be about 6.4 for the former and about 11 for the latter. The effect of flotation time. pH, surfactant(sodium lauryl sulfate), foreign ions(Na{sup +}, Ca{sup 2+}, No{sub 3}{sup -}, SO{sub 2}{sup -4} ) on the efficiency of Cd(II) removal were discussed. The presence of foreign ions inhibit the Cd(II) removal by foam flotation. It was suggested that the limitation of foam flotation on Cd(II) removal may be overcome by the surface activity of mixed surfactant solution. The application of the synergistic effect of mixed surfactant solutions to the improvement of the removal efficiency of foam flotation was experimentally verified in this work. 19 refs., 7 figs., 3 tabs.

Indium flotation from hydrometallurgical solutions

International Nuclear Information System (INIS)

Sviridov, V.V.; Mal'tsev, G.I.; Petryakova, N.K.; Gomzikov, A.I.

1980-01-01

The principal possibility of flotation of indium small quantities (10 -4 gxion/l) is established from sulphuric-acid solutions of leaching converter dusts of the copper melting production in the form of complex compounds with sodium hexametaphosphate and cation-active nitrogen-containing surfactants. It is shown that the flotation process effectiveness is determined by the molar ratio of hexametaphosphate and collector introduced into the solution, solution oxidity and surfactant nature

Removal of Cobalt Ion by Adsorbing Colloidal Flotation

Energy Technology Data Exchange (ETDEWEB)

Jung, In Ha; Lee, Jung Won [Korea Atomic Energy Research Institute, Taejon (Korea)

1998-09-30

Simulated waste liquid containing 50 ppm cobalt ion was treated by adsorbing colloidal flotation using Fe(III) or Al(III) as flocculant and a sodium lauryl sulfate as a collector. Parameters such as pH, surfactant concentration, Fe(III) or Al(III) concentration, gas flow rate, etc., were considered. The flotation with Fe(III) showed 99.8% removal efficiency of cobalt on the conditions of initial cobalt ion concentration 50 ppm, pH 9.5, gas flow rate 70 ml/min, and flotation time 30 min. When the waste solution was treated with 35% H{sub 2}O{sub 2} prior to adsorbing colloidal flotation, the optimal pH for removing cobalt shifted to weak alkaline range and flotation could be applied in wider range of pH as compared to non-use of H{sub 2}O{sub 2}. Additional use of 20 ppm Al(III) after precipitation of 50 ppm Co(II) with 50 ppm Fe(III) made the optimal pH range for preferable flotation wider. Foreign ions such as, NO{sub 3}{sup -}, SO{sub 4}{sup 2-}, Na{sup +}, Ca{sup 2+} were adopted and their effects were observed, Of which sulfate ion was found to be detrimental to removal of cobalt ion by flotation. Coprecipitation of Co ion with Fe(III) and Al(III) resulted in better removal efficiency of cobalt ion in the presence of sulfate ion. (author). 14 refs., 13 figs.

Thermodynamic condition for ''Gamma'' flotation

International Nuclear Information System (INIS)

Kaoma, J.; Yarar, B.

1989-01-01

Using the definition of the critical surface tension of wetting solids (Γc) and Gibb's adsorption isotherm, coupled with Young-Dupre's equation, the equilibrium thermodynamic condition for 'GAMMA' flotation has been derived. It is defined by the relation, Cos Oe=Γc/Γlg. At equilibrium for 'Gamma' flotation to occur, the liquid/gas interfacial tension (9γlg) should be larger than the critical surface tension of wetting of the solid surface, meaning that the equilibrium contact angle (Oe) should be greater than Zero, or cos Oe < 1, a Pre- requisite for the solid/gas bubble attachment. This definition holds for solid surfaces in the absence of any specific adsorption at the solid/liquid and solid/gas inter faces. Contact angle and flotation data are presented to sustain this definition. (author)., 15 refs., 9 figs

Bibliometric analysis on kaolinite flotation

OpenAIRE

Lieberknecht, Gabriela; Matai, Patrícia Helena Lara dos Santos; Leal Filho, Laurindo de Salles

2017-01-01

Abstract The current work presents a bibliometric discussion on articles published worldwide concerning kaolinite flotation in international journals from 1992 to 2015. In total, 39 articles were selected from Elsevier's database, SciVerse ScienceDirect. This work allowed to recognize and identify which are the thematic and methodological trends that are being used, in addition to the main collectors used in kaolinite flotation. The results show that a significant amount of articles is produc...

Studies on upgrading quality of zircon concentrate by flotation method

International Nuclear Information System (INIS)

Nguyen Duy Phap; Nguyen Duc Hung; Nguyen Duc Thai and others

2004-01-01

Results of this study show that it is possible to apply flotation to upgrading quality of zircon concentrate based on a simple technological flow-sheet and simple flotation agents. It is possible to use flotation equipment of Mexanov. Product criteria include ZrO 2 >64%; TiO 2 2 O 3 <0.1%. Flotation agents are simple, little noxious and easy for preparation. (PQM)

Effect of carboxymethyl cellulose and ionic strength on stability of mineral suspensions in potash ore flotation systems.

Science.gov (United States)

Pawlik, M; Laskowski, J S; Ansari, A

2003-04-15

The adsorption of sodium carboxymethyl cellulose from aqueous solutions varying in ionic strength from that of distilled water to 50% NaCl/KCl brine (about 3.5 mol/dm(3)) onto illite and dolomite has been studied. The purpose of this work was to investigate the solvency effects in the phenomena underlying the potash flotation process that is carried out in saturated brine. Based on viscosity measurements, the adsorption results were analyzed in terms of a simple model of polymer macromolecules in solution. Suspension stability measurements carried out concomitantly with adsorption tests showed the ranges of carboxymethyl cellulose concentration over which the tested suspensions either were aggregated or were restabilized.

Phytostabilization of Zn-Pb ore flotation tailings with Dianthus carthusianorum and Biscutella laevigata after amending with mineral fertilizers or sewage sludge.

Science.gov (United States)

Ciarkowska, Krystyna; Hanus-Fajerska, Ewa; Gambuś, Florian; Muszyńska, Ewa; Czech, Tomasz

2017-03-15

Zinc-lead mining wastes remain largely unvegetated and prone to erosion for many years because of phytotoxic levels of residual heavy metals, low nutrient status and poor physical structure. The optimal solution for these areas is to restore plant cover using species which spontaneously appear on the spoils. These species are adapted to the conditions of tailings, and their establishment will promote further vegetation by increasing soil organic matter and development of a soil system capable of supporting the nutrient and water requirements of plants and microoorganisms. The potential of Dianthus carthusianorum and Biscutella laevigata to stabilize mine spoils was analysed in a three-year pot experiment. Post-flotation wastes accumulated after Zn and Pb recovery from ores, were collected from tailings and used as a substrate for plant growth. Seeds for seedling production were collected from plants growing spontaneously on mine tailings. Prior to the establishment of the three-year pot experiment, the substrate was amended with fertilizer NPK or municipal sewage sludge, supplemented with K 2 O (SS). Substrate samples were collected for chemical analyses, dehydrogenase and urease activities measurements each year at the end of the growing season. The plants were harvested three years after the amendments. Both tested plant species were equally suitable for revegetation of the tailings. The amendment including both SS and NPK resulted in an increase of C org , N t , available P, K, Mg contents, an increase of dehydrogenase (DHA) and urease activities and a decrease in the concentrations of the soluble forms of Zn, Pb and Cd. However, nutrient content, DHA activity and plant biomass were higher with SS than NPK addition. NPK application enhanced the substrate properties after the first growing season, while positive effects of SS use were still observed after three years. A longer-lasting positive effect of SS than NPK application was probably due to the high organic

Application of Odor Sensors to Ore Sorting and Mill Feed Control

Energy Technology Data Exchange (ETDEWEB)

Michael G. Nelson

2005-08-01

Control of the feed provided to mineral processing facilities is a continuing challenge. Much effort is currently being devoted to overcoming these problems. These projects are usually described under the general headings of Mine-to-Mill Integration or Mine-Mill Optimization. It should be possible to combine the knowledge of ore type, mineralogy, and other characteristics (located in the mine modeling system), with the advanced capabilities of state-of-the-art mill control systems, to achieve an improved level of control in mineral processing that will allow optimization of the mill processes on an almost real-time basis. This is not happening because mill feed it is often treated as a uniform material, when in reality it varies in composition and characteristics. An investigation was conducted to assess the suitability of odor sensors for maintaining traceability in ore production and processing. Commercially available sensors are now used in food processing, environmental monitoring, and other applications and can detect the presence of very small amounts (0.1-500 ppm) of some molecules. An assortment of such molecules could be used to ''tag'' blocks of ore as they are mined, according to their respective characteristics. Then, as the ore came into the mill, an array of ''electronic noses'' could be used to assess its characteristics in real time. It was found that the Cyranose 320{trademark}, a commercially available odor sensor, can easily distinguish among samples of rock marked with almond, cinnamon, citronella, lemon, and orange oils. Further, the sensor could detect mixtures of rocks marked with various combinations of these oils. Treatment of mixtures of galena and silica with odorant compounds showed no detrimental effects on flotation response in laboratory tests. Additional work is recommended to determine how this concept can be extended to the marking of large volumes of materials.

Influence of agitation intensity on flotation rate of apatite particles

Directory of Open Access Journals (Sweden)

Francisco Gregianin Testa

Full Text Available Abstract The agitation intensity has a directly influence on flotation performance, lifting the particles and promoting the contact of bubbles and particles. In this paper, the energy input by the agitation on apatite flotation was investigated. The influence of pulp agitation in the flotation rate of particles with different sizes and two dosage levels was evaluated by batch testing. The flotation tests were conducted in an oscillating grid flotation cell (OGC, developed to promote a near isotropic turbulence environment. The cell is able to control the intensity of agitation and measure the energy transferred to the pulp phase. A sample of pure apatite was crushed (P80=310µm, characterized and floated with sodium oleate as collector. Four levels of energy dissipation, from 0.1 to 2 kWm-3, and two levels of collector dosage are used during the tests. The flotation kinetics by particle size were determined in function of the energy transferred. The results show a strong influence of the agitation intensity on the apatite flotation rate with both low and high dosage. For fine particles, when increasing the energy input, the flotation rate increase too, and this fact can be attributed to elevation of bubble-particle collisions. The kinetic result for the coarse particles demonstrated a reduction of the flotation rate whenever the energy input for this particle size was increased, whereby the turbulence caused by the agitation promotes the detachment of bubble-particle.

The Influence of Backwater Al3+ on Diaspore Bauxite Flotation

Directory of Open Access Journals (Sweden)

Chaojun Fang

2017-10-01

Full Text Available The effect of Al3+ in backwater on the flotation of diaspore bauxite was investigated by micro-flotation tests and the underlying mechanisms were investigated by inductively coupled plasma (ICP measurement, zeta potential measurements, solution chemistry analyses, and synchrotron near edge X-ray absorption fine structure (NEXAFS analyses. The ICP measurement results show the concentration of Al3+ in backwater was up to 1 × 10−4 mol/L. The micro-flotation results indicated that backwater Al3+ reduced the flotation recovery of diaspore and improved the flotation recovery of kaolinite at pH 9, which was the pH value used in the industrial flotation. The adsorption of Al3+ species changed the zeta potential, the Al atomic abundance, and the number of active sites on the mineral surface. In particular, the result of solution chemistry analyses and synchrotron NEXAFS analyses show that the Al3+ in backwater was adsorbed on the mineral surface in the form of Al(OH3 (s, and the bond of –Al–O–Al–(OH2 or –Al/Si–O–Al–(OH2 was formed at pH 9. It changed the intensity of hydrogen bond force between minerals and collectors, and resulted in the depression of diaspore flotation and the activation of kaolinite flotation. This study can be used to guide the application of backwater in the flotation of diaspore bauxite in industry.

Treatment of shower and laundry liquid radwaste by foam flotation

Energy Technology Data Exchange (ETDEWEB)

Jeong, In Ha; Lee, Jeong Won; Park, Hee Seong; Lee, Chul Yong; Kang, Kwon Ho [Korea Atomic Energy Research Institute, Taejon (Korea)

1998-06-01

Shower and laundry water containing surfactant were treated by precipitate flotation and adsorbing colloidal flotation. In precipitate flotation, 99.8% of removal efficiency was attained at cobalt ion concentration 50ppm, pH 9.5, gas flow rate 70ml/min and flotation time 30min. In adsorbing colloidal flotation using Fe(III) as a collector, 99.8% removal efficiency was attained at initial cobalt ion concentration 50ppm, pH 8.5, gas flow rate 70ml/min and flotation time 15 min. By adding Al(III) 20ppm after coprecipitating cobalt ion with Fe(III), operation pH range was more enlarged than using Fe(III) or Al(III) each. NaNO{sub 3}, Na{sub 2}SO{sub 4}, NaCl, CaCl{sub 2} were added as foreign ions. Removal efficiency by precipitate flotation and adsorbing colloidal flotation for the cobalt solution containing 0.1M Na{sub 2}SO{sub 4} were about 90% and 72% due to the decreased Zeta potential and the interruption of precipitation. Using Al(III) as a activator at solution containing 0.1M Na{sub 2}SO{sub 4}, the removal efficiency was increased up to 99%. (author). 24 refs., 25 figs., 1 tab.

Coal and potash flotation enhancement using a clay binder

Energy Technology Data Exchange (ETDEWEB)

Tao, D.; Chen, G.L.; Zhou, X.H.; Zhao, C.; Fan, M.M.; Aron, M.; Wright, J. [University of Kentucky, Lexington, KY (United States)

2007-07-15

The adverse effects of clay particles on coal and mineral processing operations such as gravity separation, flotation, filtration and thickening are well known in the mining industry. In particular, the presence of ultra-fine clay particles deteriorates froth flotation performance, which has been attributed to slime coatings that inhibit bubble attachment and to adsorption of the frother and/or collector by the clay particles. The present study was conducted to evaluate the performance of a clay binding agent developed by Georgia-Pacific Resins, Inc. in enhancing coal and mineral flotation performance. Mechanical flotation tests were carried out using coal and potash samples. Process parameters investigated included slurry solids percentage, impeller rotation speed, binder dosage, etc. Flotation results show that the use of GP reagents significantly enhanced flotation efficiency under different conditions. The required binder dosage and conditioning time were about 0.45 kg/t and 0.5 to 1 minute, respectively. More significant improvements in process performance were observed at higher solids percentage and higher impeller rotation speed.

Design of a new flotation system for industrial waters treatment

International Nuclear Information System (INIS)

Forero, J E; Diaz, J; Blandon V R

1999-01-01

The air flotation is a process of physical separation for the industrial wastewater treatment that removes oils and suspended solids. Although methods different from flotation have been used in petroleum industry, their application is subjected to numerous operational and economic limitations. In this work some comparisons of these flotation techniques are discussed and, a new system for the treatment of residual waters by flotation is the developed. This system is the result of several years of research both in laboratory and in pilot plants. The new design uses characteristics from other techniques, it is based on a modification of a system of induced air flotation as to operate like a system of dissolved air flotation, which improves its performance at lower costs and reduces operational problems associated with equipment maintenance. The developed system has several characteristics that improve its operation, including the use of nozzles for gas injection and dispersion in the liquid phase. As opposed to conventional systems, there is no need to use motorized bubble generating equipment for each flotation cell, diminishing therefore power requirements

Remediation of metal-contaminated urban soil using flotation technique

Energy Technology Data Exchange (ETDEWEB)

Dermont, G., E-mail: dermonge@gmail.com [Institut National de la Recherche Scientifique Eau Terre et Environnement (INRS-ETE), 490, rue de la Couronne, Quebec, QC, Canada G1K 9A9 (Canada); Bergeron, M.; Richer-Lafleche, M.; Mercier, G. [Institut National de la Recherche Scientifique Eau Terre et Environnement (INRS-ETE), 490, rue de la Couronne, Quebec, QC, Canada G1K 9A9 (Canada)

2010-02-01

A soil washing process using froth flotation technique was evaluated for the removal of arsenic, cadmium, copper, lead, and zinc from a highly contaminated urban soil (brownfield) after crushing of the particle-size fractions > 250 {mu}m. The metal contaminants were in particulate forms and distributed in all the particle-size fractions. The particle-by-particle study with SEM-EDS showed that Zn was mainly present as sphalerite (ZnS), whereas Cu and Pb were mainly speciated as various oxide/carbonate compounds. The influence of surfactant collector type (non-ionic and anionic), collector dosage, pulp pH, a chemical activation step (sulfidization), particle size, and process time on metal removal efficiency and flotation selectivity was studied. Satisfactory results in metal recovery (42-52%), flotation selectivity (concentration factor > 2.5), and volume reduction (> 80%) were obtained with anionic collector (potassium amyl xanthate). The transportation mechanisms involved in the separation process (i.e., the true flotation and the mechanical entrainment) were evaluated by the pulp chemistry, the metal speciation, the metal distribution in the particle-size fractions, and the separation selectivity indices of Zn/Ca and Zn/Fe. The investigations showed that a great proportion of metal-containing particles were recovered in the froth layer by entrainment mechanism rather than by true flotation process. The non-selective entrainment mechanism of the fine particles (< 20 {mu}m) caused a flotation selectivity drop, especially with a long flotation time (> 5 min) and when a high collector dose is used. The intermediate particle-size fraction (20-125 {mu}m) showed the best flotation selectivity.

Remediation of metal-contaminated urban soil using flotation technique.

Science.gov (United States)

Dermont, G; Bergeron, M; Richer-Laflèche, M; Mercier, G

2010-02-01

A soil washing process using froth flotation technique was evaluated for the removal of arsenic, cadmium, copper, lead, and zinc from a highly contaminated urban soil (brownfield) after crushing of the particle-size fractions >250microm. The metal contaminants were in particulate forms and distributed in all the particle-size fractions. The particle-by-particle study with SEM-EDS showed that Zn was mainly present as sphalerite (ZnS), whereas Cu and Pb were mainly speciated as various oxide/carbonate compounds. The influence of surfactant collector type (non-ionic and anionic), collector dosage, pulp pH, a chemical activation step (sulfidization), particle size, and process time on metal removal efficiency and flotation selectivity was studied. Satisfactory results in metal recovery (42-52%), flotation selectivity (concentration factor>2.5), and volume reduction (>80%) were obtained with anionic collector (potassium amyl xanthate). The transportation mechanisms involved in the separation process (i.e., the true flotation and the mechanical entrainment) were evaluated by the pulp chemistry, the metal speciation, the metal distribution in the particle-size fractions, and the separation selectivity indices of Zn/Ca and Zn/Fe. The investigations showed that a great proportion of metal-containing particles were recovered in the froth layer by entrainment mechanism rather than by true flotation process. The non-selective entrainment mechanism of the fine particles (flotation selectivity drop, especially with a long flotation time (>5 min) and when a high collector dose is used. The intermediate particle-size fraction (20-125 microm) showed the best flotation selectivity. Copyright 2009 Elsevier B.V. All rights reserved.

Hydrometalurgical processes for mineral complexes

International Nuclear Information System (INIS)

Barskij, L.A.; Danil'chenko, L.M.

1977-01-01

Requirements for the technology of the processing of ores including uranium ores and principal stages of the working out of technological schemes are described in brief. There are reference data on commercial minerals and ores including uranium-thorium ores, their classification with due regard for physical, chemical and superficial properties which form the basis for ore-concentrating processes. There are also presented the classification of minerals including uranium minerals by their flotation ability, flotation regimes of minerals, structural-textural characteristics of ores, genetic types of ore formations and their concentrating ability, algorithmization of the apriori evaluation of the concentration and technological diagnostics of the processing of ores. The classification of ore concentration technique is suggested

Picobubble enhanced column flotation of fine coal

Energy Technology Data Exchange (ETDEWEB)

Tao, D.; Yu, S.; Parekh, B.K. [University of Kentucky, Lexington, KY (United States). Mining Engineering

2006-07-01

The purpose is to study the effectiveness of picobubbles in the column flotation of -28 mesh fine coal particles. A flotation column with a picobubble generator was developed and tested for enhancing the recovery of ultrafine coal particles. The picobubble generator was designed using the hydrodynamic cavitation principle. A metallurgical and a steam coal were tested in the apparatus. The results show that the use of picobubbles in a 2in. flotation column increased the recovery of fine coal by 10 to 30%. The recovery rate varied with feed rate, collector dosage, and other column conditions. 40 refs., 8 figs., 2 tabs.

Flotation: A promising microalgae harvesting and dewatering technology for biofuels production.

Science.gov (United States)

Ndikubwimana, Theoneste; Chang, Jingyu; Xiao, Zongyuan; Shao, Wenyao; Zeng, Xianhai; Ng, I-Son; Lu, Yinghua

2016-03-01

Microalgal biomass as renewable energy source is believed to be of great potential for reliable and sustainable biofuels production. However, microalgal biomass production is pinned by harvesting and dewatering stage thus hindering the developing and growing microalgae biotechnology industries. Flotation technology applied in mineral industry could be potentially applied in microalgae harvesting and dewatering, however substantial knowledge on different flotation units is essential. This paper presents an overview on different flotation units as promising cost-effective technologies for microalgae harvesting thus bestowing for further research in development and commercialization of microalgae based biofuels. Dispersed air flotation was found to be less energy consuming. Moreover, Jameson cell flotation and dispersed ozone flotation are believed to be energy efficient microalgae flotation approaches. Microalgae harvesting and dewatering by flotation is still at embryonic stage, therefore extended studies with the focus on life cycle assessment, sustainability of the flotation unit, optimization of the operating parameters using different algal species is imperative. Though there are a number of challenges in microalgae harvesting and dewatering, with well designed and developed cultivation, harvesting/dewatering, extraction and conversion technologies, progressively, microalgae technology will be of great potential for biological carbon sequestration, biofuels and biochemicals production. Copyright © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Uranium mineralization of the Witwatersrand and Dominion Reef systems

International Nuclear Information System (INIS)

Simpson, P.R.; Bowles, J.F.W.

1977-01-01

Uranium-bearing minerals in the Witwatersrand and Dominion Reef sediments have been studied by ore microscopic, electron microprobe, fission track and neutron activation analytical methods to determine the controls of uranium mineralization. In the Dominion Reef, which represents a high-energy banket type of depositional environment, allogenic thorian uraninite occurs in hydraulic equivalence with allogenic pyrite, quartz and possibly also gold in the sediments which have uranium-thorium ratios between 3.1 and 5.6 indicating substantial amounts of thorium-rich resistate minerals. The Witwatersrand sediments have uranium-thorium ratios ranging between 7.1 and 19.6 indicating lesser amounts of resistates which is consistent with the lower-energy depositional environment. The proximal or nearshore deposits are of banket type but are distinguished from the Dominion Reef by the abundance of concretionary pyrite formed within the Basin and the presence of carbonaceous matter. The distal deposits formed at greater distance from the shoreline contain decaying organic material which has precipitated both uranium and gold from solution. Subsequent metamorphism has resulted in the formation of carbonaceous material bearing finely disseminated low-thorium pitchblende and a fine dissemination of gold associated with sulphides and arsenides. (author)

Improved flotation recovery via hydrophobicity adjustment

Energy Technology Data Exchange (ETDEWEB)

Philip Ofori; Graham O' Brien; Bruce Firth; Clint McNally; Anh Nguyen [University of Queensland, Qld. (Australia). CSIRO

2009-03-15

The main goal of this project was to examine a new approach to maximising the recovery of product specification coal during coal flotation using new generation reagents complemented by the use of the Coal Grain Analysis tool. Laboratory flotation experiments in which the novel reagents were employed as promoters by adding small amounts before adding conventional collector (diesel oil) showed that flotation recovery was significantly increased with only a small product quality (ash%) penalty. The groups of reagents used included surfactants from the group of tri-block copolymers of polyethylene oxide (PEO) and polypropylene oxide (PPO) often denoted as PEO/PPO/PEO or the reverse block copolymer PPO/PEO/PPO. Analysis of the flotation products using the grain analysis technique determined that whilst the recoveries of most grain types were improved, the coarse composite grains which were the components targeted for enhancement showed the most improvement. Plant scale test results confirmed the laboratory findings with remarkable improvements in recovery achieved for all components, especially for coarse inertite and composite grains. The difficult to float coals that are lost at this plant may be recovered without significant modification to the fines circuit by the use of targeted reagents.

Some physicochemical aspects of water-soluble mineral flotation.

Science.gov (United States)

Wu, Zhijian; Wang, Xuming; Liu, Haining; Zhang, Huifang; Miller, Jan D

2016-09-01

Some physicochemical aspects of water-soluble mineral flotation including hydration phenomena, associations and interactions between collectors, air bubbles, and water-soluble mineral particles are presented. Flotation carried out in saturated salt solutions, and a wide range of collector concentrations for effective flotation of different salts are two basic aspects of water-soluble mineral flotation. Hydration of salt ions, mineral particle surfaces, collector molecules or ions, and collector aggregates play an important role in water-soluble mineral flotation. The adsorption of collectors onto bubble surfaces is suggested to be the precondition for the association of mineral particles with bubbles. The association of collectors with water-soluble minerals is a complicated process, which may include the adsorption of collector molecules or ions onto such surfaces, and/or the attachment of collector precipitates or crystals onto the mineral surfaces. The interactions between the collectors and the minerals include electrostatic and hydrophobic interactions, hydrogen bonding, and specific interactions, with electrostatic and hydrophobic interactions being the common mechanisms. For the association of ionic collectors with minerals with an opposite charge, electrostatic and hydrophobic interactions could have a synergistic effect, with the hydrophobic interactions between the hydrophobic groups of the previously associated collectors and the hydrophobic groups of oncoming collectors being an important attractive force. Association between solid particles and air bubbles is the key to froth flotation, which is affected by hydrophobicity of the mineral particle surfaces, surface charges of mineral particles and bubbles, mineral particle size and shape, temperature, bubble size, etc. The use of a collector together with a frother and the use of mixed surfactants as collectors are suggested to improve flotation. Copyright © 2016 Elsevier B.V. All rights reserved.

Geochemical atlas of Radovish and the environs and the distribution of heavy metals in the air

International Nuclear Information System (INIS)

Stafilov, Trajche; Bacheva, Katerina; Boev, Blazho; Shajn, Robert; Balabanova, Biljana

2010-01-01

Mining activities, ore processing and processing of waste are potential emitters of heavy metals in air. As more important are mining activities on surface excavation of ore due to the large number of direct polluting factors that are difficult to control and manage. Special emphasis is given to the organization of the pit (road movement of dampers carrying ore waste), waste management (ore and flotation tailings) as well as the frequency of explosions for excavation of mining minerals. One of the major emission sources of some metals in the eastern part of the R. Macedonia is Buchim copper mine and flotation, near the town of Radovish. The mine and plant for the preparation of ore are in function from the late seventies of the last century. Ore excavation is from open pit and the ore tailings are stored in the open, in mine vicinity. The produced copper ore from the mine is processed in the flotation tailings are separated, disposed of and deposited on a dump site in an adjacent valley near the village Topolnica.

Modeling and prediction of flotation performance using support vector regression

Directory of Open Access Journals (Sweden)

Despotović Vladimir

2017-01-01

Full Text Available Continuous efforts have been made in recent year to improve the process of paper recycling, as it is of critical importance for saving the wood, water and energy resources. Flotation deinking is considered to be one of the key methods for separation of ink particles from the cellulose fibres. Attempts to model the flotation deinking process have often resulted in complex models that are difficult to implement and use. In this paper a model for prediction of flotation performance based on Support Vector Regression (SVR, is presented. Representative data samples were created in laboratory, under a variety of practical control variables for the flotation deinking process, including different reagents, pH values and flotation residence time. Predictive model was created that was trained on these data samples, and the flotation performance was assessed showing that Support Vector Regression is a promising method even when dataset used for training the model is limited.

Innovations in the flotation of fine and coarse particles

Science.gov (United States)

Fornasiero, D.; Filippov, L. O.

2017-07-01

Research on the mechanisms of particle-bubble interaction has provided valuable information on how to improve the flotation of fine (100 µm) with novel flotation machines which provide higher collision and attachment efficiencies of fine particles with bubbles and lower detachment of the coarse particles. Also, new grinding methods and technologies have reduced energy consumption in mining and produced better mineral liberation and therefore flotation performance.

Study on the flotation technology for deep-cleaning of coal slime

Energy Technology Data Exchange (ETDEWEB)

Fu Xiao-heng; Shan Xiao-yun; Jiang He-jin; Li Xiang-li [China University of Mining and Technology, Beijing (China). School of Chemical and Environmental Engineering

2006-07-01

The paper introduced the basic principle and special features of deep-cleaning of coal slime by flotation, first, separating the slime by conventional flotation to give a relatively low ash concentrate, a tailing containing an ash as high as possible, followed by flocculation-flotation to recover additional low ash concentrate. The regressive release flotation test and microphoto indicated that the middling consists mainly of intergrowth particles of coal and minerals. Comparison between deep-cleaning and conventional flotation results denoted that, at approximately same concentrate ash, its yield by deep-cleaning was 46.06 percent point higher, and at similar yield, its concentrate ash, 1.78 percent point lower. The performance by deep-cleaning is even better than that by regressive release flotation test. 4 refs., 2 figs., 6 tabs.

Integrated interpretation of 3D seismic data to enhance the detection of the gold-bearing reef: Mponeng Gold mine, Witwatersrand Basin (South Africa)

CSIR Research Space (South Africa)

Manzi, M

2015-07-01

Full Text Available The authors present an integrated approach to the seismic interpretation of one of the world's deepest gold ore body (Carbon Leader Reef) using three-dimensional seismic data, ultrasonic velocity measurements at elevated stresses, and modified...

Effect of Flotation Time on the Deinking Process and Properties of Deinked Pulp

Directory of Open Access Journals (Sweden)

Sami İmamoğlu

2012-11-01

Full Text Available This paper discusses the influence of flotation time on the ink removal and physical properties of resulting deinked pulp. Flotation deinking of high quality office paper, printed in a digital duplicating machine based on screen-printing system, was studied using a laboratory cell with a nominal capacity of 10 L. Formamidine sulfinic acid was used in a pulper and pulping conditions such as temperature, retention time, chemical dosage and consistency were held constant prior to flotation process. During the flotation process while pulp consistency, agitation speed, air flow rate and other conditions keeping constant, only flotation time were analyzed in terms of physical properties of resulting pulp quality, pulp yield, filler and fibre balance and waste water quality aspects at 0, 3, 6, 9, 12 and 15 minutes. Increased flotation time substantially affected optical properties of pulp up to some point then became steady. Yield losses increased as might be expected with increasing flotation time by the 9th minute as flotation sludge skimmed off on top of the flotation cell. Filler content of flotation sludge increased with increasing flotation time while fibre content was decreasing to a certain extent. Thanks to removal of ink and filler materials from pulp physical properties of evaluated handsheets enhanced. The overall results demonstrate that increasing flotation time increased physical and optical properties of resulting pulp. On the other hand flotation time should be increased up to critical point. Exceeding critical point increased yield losses, consumed time and energy without gaining significant pulp qualities.

Modelling Of Flotation Processes By Classical Mathematical Methods - A Review

Science.gov (United States)

Jovanović, Ivana; Miljanović, Igor

2015-12-01

Flotation process modelling is not a simple task, mostly because of the process complexity, i.e. the presence of a large number of variables that (to a lesser or a greater extent) affect the final outcome of the mineral particles separation based on the differences in their surface properties. The attempts toward the development of the quantitative predictive model that would fully describe the operation of an industrial flotation plant started in the middle of past century and it lasts to this day. This paper gives a review of published research activities directed toward the development of flotation models based on the classical mathematical rules. The description and systematization of classical flotation models were performed according to the available references, with emphasize exclusively given to the flotation process modelling, regardless of the model application in a certain control system. In accordance with the contemporary considerations, models were classified as the empirical, probabilistic, kinetic and population balance types. Each model type is presented through the aspects of flotation modelling at the macro and micro process levels.

The Effect of Conditioning on the Flotation of Pyrrhotite in the Presence of Chlorite

OpenAIRE

Yanfei Chen; Qing Shi; Qiming Feng; Yiping Lu; Wencai Zhang

2017-01-01

The influence of conditioning on the flotation of pyrrhotite in the presence of chlorite was investigated through flotation tests, sedimentation tests, and X-ray photoelectron spectroscopy (XPS) analysis. The flotation results show that chlorite slimes dramatically impair the flotation of pyrrhotite. Sedimentation and flotation tests reveal that conditioning can effectively remove chlorite slimes from pyrrhotite surfaces, resulting in an enhanced flotation recovery of pyrrhotite. When mixed m...

Effect of ultrasound on flotation kinetics in the reactor-separator

International Nuclear Information System (INIS)

Filippov, L O; Matinin, A S; Samiguin, V D; Filippova, I V

2013-01-01

Effect of the ultrasound on flotation kinetics in reactor-separator has been studied for chalcopyrite/quartz mix mineral system. Under ultrasound treatment, recovery of chalcopyrite into bulk concentrate is higher than that at reagent-only treatment. It can be explained by increased of flotation rate for slow fraction as defined by Kelsall model. The slow fraction flotation rate increase multiplied by 6 vs. ultrasound treatment. Additional effect of the ultrasound treatment has been noticed under conditions when gangue minerals detachment from bubbles can be controlled. Reactor-separator has advantages over other types of flotation cells for this purpose providing a special zone for the ultrasound treatment that can be easily designed in this impeller less machine. The ultrasound influence on particles collision probability is able to explain of chalcopyrite recovery increase in the concentrate and activation chalcopyrite particles flotation.

Effect of ultrasound on flotation kinetics in the reactor-separator

Science.gov (United States)

Filippov, L. O.; Matinin, A. S.; Samiguin, V. D.; Filippova, I. V.

2013-03-01

Effect of the ultrasound on flotation kinetics in reactor-separator has been studied for chalcopyrite/quartz mix mineral system. Under ultrasound treatment, recovery of chalcopyrite into bulk concentrate is higher than that at reagent-only treatment. It can be explained by increased of flotation rate for slow fraction as defined by Kelsall model. The slow fraction flotation rate increase multiplied by 6 vs. ultrasound treatment. Additional effect of the ultrasound treatment has been noticed under conditions when gangue minerals detachment from bubbles can be controlled. Reactor-separator has advantages over other types of flotation cells for this purpose providing a special zone for the ultrasound treatment that can be easily designed in this impeller less machine. The ultrasound influence on particles collision probability is able to explain of chalcopyrite recovery increase in the concentrate and activation chalcopyrite particles flotation.

The Effect of Conditioning on the Flotation of Pyrrhotite in the Presence of Chlorite

Directory of Open Access Journals (Sweden)

Yanfei Chen

2017-07-01

Full Text Available The influence of conditioning on the flotation of pyrrhotite in the presence of chlorite was investigated through flotation tests, sedimentation tests, and X-ray photoelectron spectroscopy (XPS analysis. The flotation results show that chlorite slimes dramatically impair the flotation of pyrrhotite. Sedimentation and flotation tests reveal that conditioning can effectively remove chlorite slimes from pyrrhotite surfaces, resulting in an enhanced flotation recovery of pyrrhotite. When mixed minerals were conditioned under the natural atmosphere, a faster conditioning speed and longer conditioning time decreased the flotation recovery of pyrrhotite. However, when mixed minerals were conditioned under a nitrogen atmosphere, a more intensive conditioning process provided better flotation results. XPS analyses illustrate that a faster conditioning speed and longer conditioning time under the natural atmosphere accelerates the oxidation of pyrrhotite, leading to a decrease in the flotation recovery of pyrrhotite.

Recent Developments in the Treatment of Uranium Ores from the Elliot Lake District

Energy Technology Data Exchange (ETDEWEB)

Downes, K W [Extraction Metallurgy Division, Department of Mines and Technical Surveys, Ottawa (Canada)

1967-06-15

A summary of the results obtained during investigations on the treatment of uranium ores from the Elliot Lake district in the laboratories of the Mines Branch, and of developments in operating procedures introduced in the uranium mills in the Elliot Lake district, is presented. Concentration of Elliot Lake ore on a pilot-plant scale by a combined gravity-flotation procedure yielded a 90% recovery of uranium at a ratio of concentration of 2.4 to 1.0. The mineralogical composition of the ore, the flow sheet used and the reagents employed are described. An approximate cost estimate indicates that, although the capacity of an existing uranium leaching plant would be doubled by introducing the procedure, the production cost per pound of U{sub 3}0{sub 8} would not be affected. Bacterial leaching of Elliot Lake ore on a laboratory scale yielded, under favourable conditions, extractions of 90 per cent in 5 weeks, and of 95 per cent in 15 weeks. The conditions that were found to influence the leaching results are outlined, and the effects of the leaching solutions are discussed. The purification of ion exchange eluates by liquid-liquid extraction, using tri-n-butyl phosphate, dibutyl butylphosphonate and tri-capryl amine in a continuous process, yielded solutions from which refined ammonium diuranate was precipitated using gaseous ammonia. The effectiveness of the three extractants is discussed, and the effects of the procedures employed on the production costs per pound of U{sub 3}O{sub 8} is estimated. Some improvements in operating procedures introduced in the Elliot Lake district uranium mills are briefly described, and their effects on the operations are indicated. Present methods of controlling radiological pollution of drainage waters by uranium mill tailings are outlined. (author)

Kinetic comparison of biological and conventional flotation of coal

Energy Technology Data Exchange (ETDEWEB)

Amini, E.; Oliazadeh, M.; Kolahdoozan, M. [University of Queensland, Brisbane, Qld. (Australia)

2009-03-15

Froth flotation is commonly used in coal processing to selectively recover the organic material (coal) from inorganic waste material. Tabas coal, located in east Iran, contains fine disseminated pyrite which is floated with coal during flotation, and hence decreasing the quality of the final concentrate. Reagents, such as sodium cyanide, are typically added to depress pyrite. Due to the toxicity of cyanide, alternative strategies for depressing pyrite flotation are being investigated. In this paper the metallurgical performance of Tabas coal treated with sodium cyanide is compared to that of Tabas coal which has undergone bacterial treatment using Acidithiobacillus ferrooxidans. Results indicate that bacterial treatment decreases the flotation rate of pyrite and improves the selectivity between coal and gangue. The possibility of using bacteria in place of toxic chemicals such as cyanide has significant environmental benefit.

Selective flotation for the removal of radionuclides from contaminated soil

International Nuclear Information System (INIS)

Miller, J.D.; Yu, Q.; Lu, Y.Q.

1995-01-01

Low-level radioactive contaminated soils (10--500 pci/gm) created by defense-related activities at certain Superfund sites, such as Nevada Test Site (NTS), is a current environmental concern. Many of these contaminated sites may require appropriate cleanup and restoration, which could cost billions of dollars and put tremendous pressure on limited financial resources. Therefore, the development of a selective flotation process to separate such radionuclides from contaminated soils should be considered. In this study, both a pure depleted UO 2 sample and three synthetic UO 2 /soil mixtures were used to evaluate surface chemistry features and to examine the possibility for the flotation of fine UO 2 particles from selected soils. It was intended that this model system would be a reasonable representation of contaminated soils such as those found the Nevada Test Site which are reported to be contaminated by PuO 2 fallout. The effect of reagent schedule, particle size distribution, and surface charge are discussed with respect to the flotation separation of the UO 2 /soil mixtures. It was found that both commercial fatty acids and reagent grade sodium oleate are effective collectors for UO 2 flotation provided the pH is adjusted to the range of pH 8--9. The bench-scale flotation results successfully demonstrated that froth flotation technology can be used to remove UO 2 from such model contaminated soils with appropriate flotation chemistry conditions which depend on the soil characteristics and other pretreatment procedures

Evaluation of Gas Phase Dispersion in Flotation under Predetermined Hydrodynamic Conditions

Science.gov (United States)

Młynarczykowska, Anna; Oleksik, Konrad; Tupek-Murowany, Klaudia

2018-03-01

Results of various investigations shows the relationship between the flotation parameters and gas distribution in a flotation cell. The size of gas bubbles is a random variable with a specific distribution. The analysis of this distribution is useful to make mathematical description of the flotation process. The flotation process depends on many variable factors. These are mainly occurrences like collision of single particle with gas bubble, adhesion of particle to the surface of bubble and detachment process. These factors are characterized by randomness. Because of that it is only possible to talk about the probability of occurence of one of these events which directly affects the speed of the process, thus a constant speed of flotation process. Probability of the bubble-particle collision in the flotation chamber with mechanical pulp agitation depends on the surface tension of the solution, air consumption, degree of pul aeration, energy dissipation and average feed particle size. Appropriate identification and description of the parameters of the dispersion of gas bubbles helps to complete the analysis of the flotation process in a specific physicochemical conditions and hydrodynamic for any raw material. The article presents the results of measurements and analysis of the gas phase dispersion by the size distribution of air bubbles in a flotation chamber under fixed hydrodynamic conditions. The tests were carried out in the Laboratory of Instrumental Methods in Department of Environmental Engineering and Mineral Processing, Faculty of Mining and Geoengineerin, AGH Univeristy of Science and Technology in Krakow.

Effects of coal composition and flotation reagents on the water resistance of binderless briquettes

Energy Technology Data Exchange (ETDEWEB)

Motaung, S.R.; Mangena, S.J.; de Korte, G.J. [Syngas & Coal Technology, Sasolburg (South Africa)

2007-10-15

The difference in the physical properties, particularly the water resistance or wet strength, of the binderless coal briquettes produced from flotation feed and concentrate was investigated using six bituminous coals from two collieries in the Witbank Coalfield. The coal samples were analyzed for their proximate, petrographic, and mineralogical properties. The presence, in the flotation concentrates, of the reagents used during the froth flotation process was also investigated using gas chromatography. Pillow-shaped binderless briquettes were produced from coal samples at various moisture contents and a pressure of approximately 17 MPA using a Komarek B-100A double-roll press. The briquettes were tested for some physical properties (i.e., dry- and wet-compressive strengths), which were thereafter compared with the properties determined for the coal samples. The binderless briquettes produced from the flotation concentrates were more water-resistant than those produced from the flotation feed. The flotation feed and concentrates of the coals tested were found to have similar petrographic properties. As expected, the ash and kaolinite contents were found to be lower in the flotation concentrates than in the flotation feed. Flotation reagents were detected in the flotation concentrates from both collieries. From the results obtained it is concluded that the increased water resistance of the binderless briquettes produced from flotation concentrates of the coals tested is due to a combination of the fineness of the coal particles, assisted by the amount of reactive macerals (most particularly vitrinite) with the lower ash and kaolinite contents, together with the presence of the flotation reagents, particularly the collector, in the flotation concentrate.

Rapid Analysis of Copper Ore in Pre-Smelter Head Flow Slurry by Portable X-ray Fluorescence.

Science.gov (United States)

Burnett, Brandon J; Lawrence, Neil J; Abourahma, Jehad N; Walker, Edward B

2016-05-01

Copper laden ore is often concentrated using flotation. Before the head flow slurry can be smelted, it is important to know the concentration of copper and contaminants. The concentration of copper and other elements fluctuate significantly in the head flow, often requiring modification of the concentrations in the slurry prior to smelting. A rapid, real-time analytical method is needed to support on-site optimization of the smelter feedstock. A portable, handheld X-ray fluorescence spectrometer was utilized to determine the copper concentration in a head flow suspension at the slurry origin. The method requires only seconds and is reliable for copper concentrations of 2.0-25%, typically encountered in such slurries. © The Author(s) 2016.

Flotation:en studie i några förutsättningar för selektiv flotation

OpenAIRE

Bolin, Nils Johan

1983-01-01

The zeta potential for oxide- and silicate minerals has been measured in different pulp liquids and a comparison has been made concerning the results of the flotation. The results show that the surface charge of the mineral particles reflect the condition of the dispersion of the pulp, and guiding the surface charge is a way of increasing the selectivity when concentrating by flotation. The results also show that the zeta potential indicates how easily amino reagents are adsorbed on silicate ...

Effects of Flotation-REST on Muscle Tension Pain

Directory of Open Access Journals (Sweden)

Anette Kjellgren

2001-01-01

Full Text Available The purpose of the present study was to investigate whether the floating form of the restricted environmental stimulation technique (REST may be applied within the field of pain relief. Flotation-REST consists of a procedure whereby an individual is immersed in a tank filled with water of an extremely high salt concentration. Thirty-seven patients (14 men and 23 women suffering from chronic pain consisting of aching muscles in the neck and back area participated in the study. They were randomly assigned to either a control group (17 participants or an experimental group (20 participants. The experimental group received nine opportunities to use the flotation-REST technique in the water tank over a three-week period. The results indicated that the most severe perceived pain intensity was significantly reduced, whereas low perceived pain intensity was not influenced by the floating technique. Further, the results indicated that circulating levels of the noradrenaline metabolite 3-methoxy-4-hydroxyphenylethyleneglycol were reduced significantly in the experimental group but not in the control group following treatment, whereas endorphin levels were not affected by flotation. Flotation-REST treatment also elevated the participants' optimism and reduced the degree of anxiety or depression; at nighttime, patients who underwent flotation fell asleep more easily. The present findings describe possible changes, for the better, in patients presenting with chronic pain complaints.

Effects of flotation-REST on muscle tension pain.

Science.gov (United States)

Kjellgren, A; Sundequist, U; Norlander, T; Archer, T

2001-01-01

The purpose of the present study was to investigate whether the floating form of the restricted environmental stimulation technique (REST) may be applied within the field of pain relief. Flotation-REST consists of a procedure whereby an individual is immersed in a tank filled with water of an extremely high salt concentration. Thirty-seven patients (14 men and 23 women) suffering from chronic pain consisting of aching muscles in the neck and back area participated in the study. They were randomly assigned to either a control group (17 participants) or an experimental group (20 participants). The experimental group received nine opportunities to use the flotation-REST technique in the water tank over a three-week period. The results indicated that the most severe perceived pain intensity was significantly reduced, whereas low perceived pain intensity was not influenced by the floating technique. Further, the results indicated that circulating levels of the noradrenaline metabolite 3-methoxy-4-hydroxyphenylethyleneglycol were reduced significantly in the experimental group but not in the control group following treatment, whereas endorphin levels were not affected by flotation. Flotation-REST treatment also elevated the participants' optimism and reduced the degree of anxiety or depression; at nighttime, patients who underwent flotation fell asleep more easily. The present findings describe possible changes, for the better, in patients presenting with chronic pain complaints.

Remediation of metal-contaminated urban soil using flotation technique

International Nuclear Information System (INIS)

Dermont, G.; Bergeron, M.; Richer-Lafleche, M.; Mercier, G.

2010-01-01

A soil washing process using froth flotation technique was evaluated for the removal of arsenic, cadmium, copper, lead, and zinc from a highly contaminated urban soil (brownfield) after crushing of the particle-size fractions > 250 μm. The metal contaminants were in particulate forms and distributed in all the particle-size fractions. The particle-by-particle study with SEM-EDS showed that Zn was mainly present as sphalerite (ZnS), whereas Cu and Pb were mainly speciated as various oxide/carbonate compounds. The influence of surfactant collector type (non-ionic and anionic), collector dosage, pulp pH, a chemical activation step (sulfidization), particle size, and process time on metal removal efficiency and flotation selectivity was studied. Satisfactory results in metal recovery (42-52%), flotation selectivity (concentration factor > 2.5), and volume reduction (> 80%) were obtained with anionic collector (potassium amyl xanthate). The transportation mechanisms involved in the separation process (i.e., the true flotation and the mechanical entrainment) were evaluated by the pulp chemistry, the metal speciation, the metal distribution in the particle-size fractions, and the separation selectivity indices of Zn/Ca and Zn/Fe. The investigations showed that a great proportion of metal-containing particles were recovered in the froth layer by entrainment mechanism rather than by true flotation process. The non-selective entrainment mechanism of the fine particles ( 5 min) and when a high collector dose is used. The intermediate particle-size fraction (20-125 μm) showed the best flotation selectivity.

Recovery of copper ion by flotation with potassium amylxanthate

International Nuclear Information System (INIS)

Ramirez-Serrano, B.; Coello-Velazquez, A. L.; Bernardo, A.; Afif, E.; Menendez-Aguado, J. M.

2012-01-01

In this paper a study about the column flotation process of copper ion employing potassium amylxanthate as collector reagent is carried out. The effect on the recovery of copper ion by the modification of variables such as collector/metal relation and surface velocity of gas and liquid was determined experimentally by the analysis of the statistic-mathematical model of the copper flotation process, as well as the physico-chemical phenomena that take place, showing the effect of the collector/metal relation in the process. The effect of pH as the main properties of the chemical system in the recovery and the kinetic of the flotation process is made too. The experimental results shows that the recovery of copper in the pH range of 4,5 - 12 is possible with prevalence of precipitate flotation. (Author) 43 refs.

Influence of Copper Ore Comminution in HPGR on Downstream Minerallurgical Processes

Directory of Open Access Journals (Sweden)

Saramak D.

2017-09-01

Full Text Available Crushing processes taking place in high-pressure grinding rolls devices (HPGR are currently one of the most efficient methods of hard ore size reduction in terms of the energy consumption. The HPGR products are characterized by a fine particle size and the micro-cracks formation in individual particles, which appears in downstream grinding processes, decreasing their energy consumption. The purpose of the paper was to analyze the effectiveness of a ball mill grinding process and flotation operations depending on the changeable conditions of run of the HPGR crushing process. The research programme carried out included crushing tests in the laboratory scale HPGR device at various settings of the operating pressure volume and selected qualitative properties of the feed material (i.e. particle size distribution. On the basis of obtained results the models, defining the grinding process effectiveness as a function of changeable conditions of HPGR process run, were determined. Based on these models the optimal grinding time in a ball mill was specified which is, in turn, the basis for optimization of operation the technological comminution circuits for a given material type. The obtained results proved that the application of HPGR devices in given copper ore comminution circuit may improve the effectiveness of downstream grinding process what leads to improvement of the entire circuit work efficiency through decreasing the process energy consumption and enhancing the product size reduction.

Recovery of clean coal fines through a combination of gravity concentrator and flotation processes

Energy Technology Data Exchange (ETDEWEB)

Gupta, A.K.; Banerjee, P.K.; Dutta, A.; Mishra, A. [Tata Steel, Jamshedpur (India). Research & Development

2007-07-01

Flotation feed is a mixture of coarse and ultra-fine fractions. During conditioning of the flotation feed with collector and frother, the finer fraction consumes more reagents as compared to coarser particles. This is mainly due to more specific surface area of the ultra fine than the coarse fraction. This favors the adsorption of reagents toward ultra-finer fractions leads to less complete surface coverage of coarse particles and more entrainment of finer gangue particles. This results in the lower yield of coarse fractions from the flotation circuit and loss in selectivity. Hence, the major challenge is to improve the recovery of the coarser fraction and selectivity of ultra-fine fractions by improving flotation kinetics of all size fractions. This article deals with an approach to overcome the improper reagent adsorption by fine and coarse coal fractions in the flotation circuit through an innovative washing circuit containing gravity operation and flotation processes. Flotation performance between a new washing circuit having stub cyclone and flotation and normal single-stage reagent addition flotation process is compared in terms of selectivity, separation efficiency, rate constant, and size-wise recovery. The washing circuit having stub cyclone and flotation processes improves the fine clean coal yield by 10% and reduces the consumption of reagent compared to the normal single-stage reagent addition flotation process.

Flotation mechanisms of molybdenite fines by neutral oils

Science.gov (United States)

Lin, Qing-quan; Gu, Guo-hua; Wang, Hui; Liu, You-cai; Fu, Jian-gang; Wang, Chong-qing

2018-01-01

The flotation mechanisms of molybdenite fines by neutral oils were investigated through microflotation test, turbidity measurements, infrared spectroscopy, and interfacial interaction calculations. The results of the flotation test show that at pH 2-11, the floatability of molybdenite fines in the presence of transformer oil is markedly better than that in the presence of kerosene and diesel oil. The addition of transformer oil, which enhances the floatability of molybdenite fines, promotes the aggregation of molybdenite particles. Fourier transform infrared measurements illustrate that physical interaction dominates the adsorption mechanism of neutral oil on molybdenite. Interfacial interaction calculations indicate that hydrophobic attraction is the crucial force that acts among the oil collector, water, and molybdenite. Strong hydrophobic attraction between the oily collector and water provides the strong dispersion capability of the collector in water. Furthermore, the dispersion capability of the collector, not the interaction strength between the oily collectors and molybdenite, has a highly significant role in the flotation system of molybdenite fines. Our findings provide insights into the mechanism of molybdenite flotation.

Selective depression behavior of guar gum on talc-type scheelite flotation

Science.gov (United States)

Zhang, Yong-zhong; Gu, Guo-hua; Wu, Xiang-bin; Zhao, Kai-le

2017-08-01

The depression behavior and mechanism of guar gum on talc-type scheelite flotation were systematically investigated by flotation experiments, adsorption tests, zeta-potential measurements, and infrared spectroscopic analyses. The flotation results for monominerals, mixed minerals, and actual mineral samples indicated that guar gum exhibited much higher selective depression for talc than for scheelite. Bench-scale closed-circuit tests showed that a tungsten concentrate with a WO3 grade of 51.43% and a WO3 recovery of 76.18% was obtained. Adsorption tests, zeta-potential measurements, and infrared spectral analyses confirmed that guar gum absorbed more strongly onto the talc surface than onto the scheelite surface because of chemisorption between guar gum and talc. This chemisorption is responsible for the guar gum's highly selective depression for talc and small depression for scheelite. The flotation results provide technical support for talc-type scheelite flotation.

Comparative results of copper flotation from smelter slag and granulated smelter slag

OpenAIRE

Milanović, Dragan; Stanujkić, Dragiša; Ignjatović, Miroslav R.

2013-01-01

Smelter slag is obtained in the process of metallurgical converting of copper concentrate in the Smelter Plant in Bor, Serbia. Today, the reserves of this material are evaluated at about more of a year, with the average copper content of 0.6-0.9%. Production of copper concentrate by flotation of smelter slag has started in 2001. Flotation concentrate goes to the Copper Smelter once more for production of copper cathodes and the rough flotation tailings go to the flotation tailing dump. Copper...

Leaching characteristics of copper flotation waste before and after vitrification.

Science.gov (United States)

Coruh, Semra; Ergun, Osman Nuri

2006-12-01

Copper flotation waste from copper production using a pyrometallurgical process contains toxic metals such as Cu, Zn, Co and Pb. Because of the presence of trace amounts of these highly toxic metals, copper flotation waste contributes to environmental pollution. In this study, the leaching characteristics of copper flotation waste from the Black Sea Copper Works in Samsun, Turkey have been investigated before and after vitrification. Samples obtained from the factory were subjected to toxicity tests such as the extraction procedure toxicity test (EP Tox), the toxicity characteristic leaching procedure (TCLP) and the "method A" extraction procedure of the American Society of Testing and Materials. The leaching tests showed that the content of some elements in the waste before vitrification exceed the regulatory limits and cannot be disposed of in the present form. Therefore, a stabilization or inertization treatment is necessary prior to disposal. Vitrification was found to stabilize heavy metals in the copper flotation waste successfully and leaching of these metals was largely reduced. Therefore, vitrification can be an acceptable method for disposal of copper flotation waste.

Flotation of beryl from milky white quartz veins of Igla area, eastern desert of egypt

International Nuclear Information System (INIS)

Abdel Monem, H.M.; Aly, M.M.; Abdel Aty, M.A.

1988-01-01

Several milky white quartz veins and lenses occur at the Igla area of the central eastern desert. These veins are beryl-bearing and are introduced into breociated rhyolite and porphyritic dolerites as country rock. An effort has been made to up-grade such a low-grade ore material and therefore a head sample assaying about o.28% Be O was prepared. Flotation technique using sodium alkyl-aryl sulfonate as a collector has proven most satisfactory for separating beryl grains at ph value less than 3.5. indeed, a best recovery exceeding 90% Be O could be obtained by adding an activator of some metal chlorides; viz Fe Cl 3 , and Pb Cl 2 and Ca Cl 2 at various PH value. The study has made possible the elaboration of a proposed flow sheet whereby a beryl concentrate assaying 9.35% Be o was obtained with an overall recovery of about 93%

Heavy metal removal from waste waters by ion flotation.

Science.gov (United States)

Polat, H; Erdogan, D

2007-09-05

Flotation studies were carried out to investigate the removal of heavy metals such as copper (II), zinc (II), chromium (III) and silver (I) from waste waters. Various parameters such as pH, collector and frother concentrations and airflow rate were tested to determine the optimum flotation conditions. Sodium dodecyl sulfate and hexadecyltrimethyl ammonium bromide were used as collectors. Ethanol and methyl isobutyl carbinol (MIBC) were used as frothers. Metal removal reached about 74% under optimum conditions at low pH. At basic pH it became as high as 90%, probably due to the contribution from the flotation of metal precipitates.

Drones for Provision of Flotation Support in Simulated Drowning.

Science.gov (United States)

Bäckman, Anders; Hollenberg, Jacob; Svensson, Leif; Ringh, Mattias; Nordberg, Per; Djärv, Therese; Forsberg, Sune; Hernborg, Olof; Claesson, Andreas

The feasibility and potential of using drones for providing flotation devices in cases of drowning have not yet been assessed. We hypothesize that a drone carrying an inflatable life buoy is a faster way to provide flotation compared with traditional methods. The purpose of this study is to explore the feasibility and efficiency of using a drone for delivering and providing flotation support to conscious simulated drowning victims. A simulation study was performed with a simulated drowning victim 100 m from the shore. A drone (DJI Phantom 4; dji, Shenzhen, China) equipped with an inflatable life buoy of 60 N was compared with traditional surf rescue swimming for providing flotation. The primary outcome was delay (minutes:seconds). A total number of 30 rescues were performed with a median time to delivery of the floating device of 30 seconds (interquartile range [IQR] = 24-32 seconds) for the drone compared with 65 seconds (IQR = 60-77 seconds) with traditional rescue swimming (P drone had an accuracy of 100% in dropping the inflatable life buoy drones to deliver inflatable life buoys is safe and may be a faster method to provide early flotation devices to conscious drowning victims compared with rescue swimming. Copyright © 2018 Air Medical Journal Associates. Published by Elsevier Inc. All rights reserved.

Influence of the amount of collector on ion flotation of niobium

International Nuclear Information System (INIS)

Ushakova, L.I.; Berezyuk, V.G.; Kasimov, A.M.

1983-01-01

Flotation methods based on chemical interaction of the metal ion to be extracted (colligend) with an oppositely charged surfactant ion (collector) are now attracting attention increasingly in purification of wastewaters. Extraction of small amounts of metals by flotation from industrial wastes provides solutions of problems associated with prevention of pollution of natural water supplies by toxic pollutants, and also with concentration of valuable elements for subsequent utilization. Niobium is one such metal, extraction of which from aqueous solutions is of considerable interest. The results of an experimental study of the influence of the amount of flotation reagent on ion flotation of niobates are discussed in this paper

Determination of gold in copper-bearing sulphide ores and metallurgical flotation products by atomic-absorption spectrometry.

Science.gov (United States)

Strong, B; Murray-Smith, R

1974-12-01

A method is described which is specific for the determination of gold in sulphide copper ores and concentrates. Direct decomposition with aqua regia was found to be incomplete. A carefully controlled roasting stage followed by treatment with hydrochloric acid and then aqua regia was effective for dissolving all the gold. The gold is extracted into 4-methylpentan-2-one (methyli-sobutylketone) then aspirated into a very lean air-acetylene flame and the gold determined by atomic-absorption spectrometry. No interferences were observed from large concentrations of copper, iron or nickel.

Possibilities for rutile extraction from Norwegian eclogite by flotation

OpenAIRE

Gaydardzhiev, Stoyan; Sandvik, Knut

1993-01-01

Preliminary flotations tests towards rutile extraction from Norwegian eclogites (Verving deposit) have been carried out. Various sulfonate type flotation reagents (produced by Hoechts) have been tested. Selectivity between rutile/pyroxene has been targeted. Rutile separation from pyrite and garnet has been further identified as principal problem.

21 CFR 880.5550 - Alternating pressure air flotation mattress.

Science.gov (United States)

2010-04-01

... body pressure. The device is used to prevent and treat decubitus ulcers (bed sores). (b) Classification... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Alternating pressure air flotation mattress. 880... Personal Use Therapeutic Devices § 880.5550 Alternating pressure air flotation mattress. (a) Identification...

Removal of arsenic in flotation of galena and sphalerite

Science.gov (United States)

Yu, Dae-hwan; Kim, Min-kyu; Han, Oh-hyung; Park, Chul-hyun

2017-04-01

In Korea, Janggun mine that produces the concentrate of galena (PbS) /sphalerite (ZnS) containing arsenic of 1.3% charges a penalty of US 3/ton to LS-Nikko smelter. Hence in this work, flotation tests for removal of arsenopyrite (FeAsS) from sulfide minerals were carried out using lab scale flotation cell, which maintain grade and recovery of PbS and ZnS in comparison to flotation plant. Particularly, this study was focused on investigating the combination of several chemical reagents such as depressant, collector, activator and etc. that affect flotation performance. In the straight differential flotation for PbS, a PbS grade of 67.80% and a recovery of 80.2% could be obtained with FeAsS removal of 84.1% (0.2% As) under the conditions of 20% feed solids concentration, pH 8.5, 50g/t frother (AF65), 50g/t collector (AP242) and 600g/t As depressant (NaHSO3) and 600g/t Zn depressant (ZnSO4). In the ZnS flotation, the maximum separation achievable for ZnS has been shown to be a grade of 50.27% and a recovery of 88.7%. At this time, FeAsS removal of 87.8% (0.16% As) could be successfully accomplished under pH 11, and 1.2kg/t Zn activator (CuSO4), 100g/t frother (AF65), 100g/t collector (AP211) and 400g/t As depressant (NaHSO3). Acknowledgments This work was supported by the Energy and Resources Engineering Program Grant funded by the Ministry of Trade, Industry and Energy, Korea

Effect of frothing and collecting agents for flotation behavior of coal

International Nuclear Information System (INIS)

Nasir, S.; Sheikh, T.S.

2011-01-01

Coal flotation is a complex process involving several phases (particles, oil droplets and air bubbles). These phases simultaneously interact with each other and with other species such as the molecules of a promoting reagent and dissolved ions in water. The physical and chemical interactions determine the outcome of the flotation process. Although the interactions between the oil droplets and coal particles are actually favored, stabilization of the oil droplets by small amounts of fine hydrophobic particles may lead to decrease in selectivity and an increased in oil consumption. These problems could be remedied by use of promoters that modify the coal surface for suitable particle-particle, droplet-particle and particle-bubble contact while emulsifying the oil droplets. In this paper, a detailed description of the coal flotation, their physical and chemical interactions with each other in the flotation pulp, the major parameters (% volatiles, % fixed carbon and heating value) that affect these interactions and how these interactions, in turn, influence the flotation process are discussed. (author)

40 CFR 440.102 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Science.gov (United States)

2010-07-01

...) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Copper, Lead, Zinc, Gold... obtain copper bearing ores, lead bearing ores, zinc bearing ores, gold bearing ores, or silver bearing... which employ the froth flotation process alone or in conjunction with other processes, for the...

Method of concentrating oil shale by flotation

Energy Technology Data Exchange (ETDEWEB)

Larsson, M

1941-01-28

A method is described of concentrating oil shale by flotation. It is characterized by grinding the shale to a grain size which, roughly speaking, is less than 0.06 mm. and more conveniently should be less than 0.05 mm., and followed by flotation. During the process the brown foam formed is separated as concentrate, while the black-brown to all-black foam is separated as a middle product, ground fine again, and thereafter floated once more. The patent contains five additional claims.

Immobilization of copper flotation waste using red mud and clinoptilolite.

Science.gov (United States)

Coruh, Semra

2008-10-01

The flash smelting process has been used in the copper industry for a number of years and has replaced most of the reverberatory applications, known as conventional copper smelting processes. Copper smelters produce large amounts of copper slag or copper flotation waste and the dumping of these quantities of copper slag causes economic, environmental and space problems. The aim of this study was to perform a laboratory investigation to assess the feasibility of immobilizing the heavy metals contained in copper flotation waste. For this purpose, samples of copper flotation waste were immobilized with relatively small proportions of red mud and large proportions of clinoptilolite. The results of laboratory leaching demonstrate that addition of red mud and clinoptilolite to the copper flotation waste drastically reduced the heavy metal content in the effluent and the red mud performed better than clinoptilolite. This study also compared the leaching behaviour of metals in copper flotation waste by short-time extraction tests such as the toxicity characteristic leaching procedure (TCLP), deionized water (DI) and field leach test (FLT). The results of leach tests showed that the results of the FLT and DI methods were close and generally lower than those of the TCLP methods.

Highly Polluted Wastewaters Treatment by Improved Dissolved Air Flotation Technology

Science.gov (United States)

Moga, I. C.; Covaliu, C. I.; Matache, M. G.; Doroftei, B. I.

2017-06-01

Numerous investigations are oriented towards the development of new wastewater treatment technologies, having high efficiencies for removing even low concentrations of pollutants found in water. These efforts were determined by the destroyer impact of the pollutants to the environment and human’s health. For this reason this paper presents our study concerning an improved dissolved air flotation technology for wastewater treatment. There is described a dissolved air flotation (DAF) installation composed by two equipments: pressurized capsule and lamellar settling. Also, there are presented some advantages of using nanoparticles as flotation collectors.

A Study of the Optimal Model of the Flotation Kinetics of Copper Slag from Copper Mine BOR

Science.gov (United States)

Stanojlović, Rodoljub D.; Sokolović, Jovica M.

2014-10-01

In this study the effect of mixtures of copper slag and flotation tailings from copper mine Bor, Serbia on the flotation results of copper recovery and flotation kinetics parameters in a batch flotation cell has been investigated. By simultaneous adding old flotation tailings in the ball mill at the rate of 9%, it is possible to increase copper recovery for about 20%. These results are compared with obtained copper recovery of pure copper slag. The results of batch flotation test were fitted by MatLab software for modeling the first-order flotation kinetics in order to determine kinetics parameters and define an optimal model of the flotation kinetics. Six kinetic models are tested on the batch flotation copper recovery against flotation time. All models showed good correlation, however the modified Kelsall model provided the best fit.

Flotation performances and surface properties of chalcopyrite with xanthate collector added before and after grinding

Science.gov (United States)

Peng, Huiqing; Wu, Di; Abdelmonem, Mohamed

In this study, effects of the collector added before grinding and after grinding on the subsequent flotation and mineral surface properties were investigated. The pH was controlled at 10 during the grinding and flotation processes opened to the atmosphere. With enough amounts of sodium butyl xanthate addition, adding the collector before grinding recovered more chalcopyrite than adding it after grinding in single mineral flotation. The Eh of each ground pulp before and after conditioning were measured and it was found that adding collector before grinding obtained higher and relatively suitable pulp potential for chalcopyrite flotation. Particle size analyses of the flotation products indicate that the different flotation recoveries occurred due to the different flotation losses in fine particles (flotation feedings and found that more carbon and oxygen, and less iron were remained on mineral surfaces when the collector was added before grinding, due to the higher collector adsorption capacity, larger free oxygen adsorbance and less iron oxide/hydroxide species.

Leaching behaviour and mechanical properties of copper flotation waste in stabilized/solidified products.

Science.gov (United States)

Mesci, Başak; Coruh, Semra; Ergun, Osman Nuri

2009-02-01

This research describes the investigation of a cement-based solidification/stabilization process for the safe disposal of copper flotation waste and the effect on cement properties of the addition of copper flotation waste (CW) and clinoptilolite (C). In addition to the reference mixture, 17 different mixtures were prepared using different proportions of CW and C. Physical properties such as setting time, specific surface area and compressive strength were determined and compared to a reference mixture and Turkish standards (TS). Different mixtures with the copper flotation waste portion ranging from 2.5 to 12.5% by weight of the mixture were tested for copper leachability. The results show that as cement replacement materials especially clinoptilolite had clear effects on the mechanical properties. Substitution of 5% copper flotation waste for Portland cement gave a similar strength performance to the reference mixture. Higher copper flotation waste addition such as 12.5% replacement yielded lower strength values. As a result, copper flotation waste and clinoptilolite can be used as cementitious materials, and copper flotation waste also can be safely stabilized/solidified in a cement-based solidification/stabilization system.

Flotation of copper-bearing shale in solutions of inorganic salts and organic reagents

OpenAIRE

Ratajczak Tomasz

2017-01-01

Flotation data on copper-bearing shale in aqueous solutions of inorganic electrolytes (NaCl, Na2SO4, KPF6, NH4Cl) and organic reagents (ethylamine, propylamine) as frothers were presented and discussed. The relationships between shale flotation, surface tension of aqueous solution and foam height during bubbling with air in the flotation system were presented. It has been found that flotation of shale in the presence of inorganic salts the yield was directly proportional to the surface tensio...

The effects of anionic and cationic surfactants on the ion flotation of Cd2+

International Nuclear Information System (INIS)

Kobayashi, Koichi

1975-01-01

The ion flotation of Cd 2+ ions has been investigated from the surface chemical point of view in comparison with the case of Cu 2+ ions reported previously. The effects of the change in the pH, the anionic and cationic surfactants, and bentonite on the flotation rate have also been studied. Sodium α-sulfolaurate proved to be one of the best surfactants among the anionic surfactants used for removing Cd 2+ ions, showing as high as a 97% removal. About 97% of the Cd 2+ ions could be floated in the region of pH 11.3 when a cationic surfactant was used with bentonite, regardless of the exact surfactant used. The addition of bentonite reduced the foam formation and liquid hold-up, resulting in effective bubble flotation. This behavior was as a whole similar to that of Cu 2+ ions. However, in all the flotation systems tested, the flotation rate increased sharply at about pH 8, and the flotation rate vs. pH curve for Cd 2+ shifted towards a more alkaline region than that for Cu 2+ , because of the stronger basic nature of the former. Also, the flotation rate of Cd 2+ ions for the Cd 2+ -anionic surfactant systems attained a steady value after about 7 min, longer than the 2-min gas flow required in the case of Cu 2+ ion flotation. The adjustment of the pH using ammonia gave a lower rate of flotation than in the case of flotation using sodium hydroxide. (auth.)

Modified binders on the basis of flotation tailings

Science.gov (United States)

Shapovalov, N. A.; Zagorodnyuk, L. Kh; Shchekina, A. Yu; Gorodov, A. I.

2018-03-01

The article proposes compositions of efficient modified composite binders on the basis of portland cement and flotation tailings; the new binders attain the ultimate compressive stress that is twice as high as that of the cement stone. At that, use of annually growing volume of flotation tailings in the production of the composite binder is a rational way for recycling this type of waste and allows saving the planet's natural resources.

Study of uranium leaching from industrial residues of Industrias Nucleares do Brazil S.A. (INB), Caetite, Bahia, Brazil

International Nuclear Information System (INIS)

Formiga, Thiago S.; Morais, Carlos A.; Gomiero, Luiz A.

2011-01-01

The uraniferous district of Lagoa Real, located in the south-central region of the state of Bahia, has reserves estimated at 100,000 tons of uranium, which is enough to supply Angra I, II and III for 100 more years. The process adopted for the beneficiation of the uranium ore from Lagoa Real is heap leaching, a static process in which the ore is crushed, disposed in heaps and irrigated with a sulfuric acid solution to remove the uranium. This technique has a relatively low cost of implementation, although the yield of uranium recovery is low, with an uranium content in the leached residue of 700 μg/g U 3 O 8 for ores with an initial content of 2,700 μg/g U 3 O 8 . With the deepening of the mine pit, an increase in the carbonate content in the ore was noted, which required a higher acid consumption in the leaching. In order to reduce the concentration of carbonates, a study of the ore concentration by flotation column was accomplished. The flotation reject had high carbonate content, with a uranium content of about 2,300 μg/g U 3 O 8 for flotation in one column and 1,100 μg/g U 3 O 8 for flotation in two columns. This paper presents the study of the leaching process for the recovery of the uranium present in the residue of the heap leaching and in the carbonated residue from the flotation of the anomaly 13 ore. The results indicate the feasibility of treating the waste of the heap leaching through dynamic leaching. The study of the uranium leaching from the flotation residue through acid leaching technique indicated a recovery of 96% of uranium, however with a high consumption of acid, around 450 kg/t, showing that for this case, the most suitable technique for the process is alkaline leaching. (author)

Study of uranium leaching from industrial residues of Industrias Nucleares do Brazil S.A. (INB), Caetite, Bahia, Brazil

Energy Technology Data Exchange (ETDEWEB)

Formiga, Thiago S.; Morais, Carlos A., E-mail: cmorais@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Gomiero, Luiz A., E-mail: gomiero@inb.gov.b [Industrias Nucleares do Brasil S/A (INB), Caetite, BA (Brazil)

2011-07-01

The uraniferous district of Lagoa Real, located in the south-central region of the state of Bahia, has reserves estimated at 100,000 tons of uranium, which is enough to supply Angra I, II and III for 100 more years. The process adopted for the beneficiation of the uranium ore from Lagoa Real is heap leaching, a static process in which the ore is crushed, disposed in heaps and irrigated with a sulfuric acid solution to remove the uranium. This technique has a relatively low cost of implementation, although the yield of uranium recovery is low, with an uranium content in the leached residue of 700 {mu}g/g U{sub 3}O{sub 8} for ores with an initial content of 2,700 {mu}g/g U{sub 3}O{sub 8}. With the deepening of the mine pit, an increase in the carbonate content in the ore was noted, which required a higher acid consumption in the leaching. In order to reduce the concentration of carbonates, a study of the ore concentration by flotation column was accomplished. The flotation reject had high carbonate content, with a uranium content of about 2,300 {mu}g/g U{sub 3}O{sub 8} for flotation in one column and 1,100 {mu}g/g U{sub 3}O{sub 8} for flotation in two columns. This paper presents the study of the leaching process for the recovery of the uranium present in the residue of the heap leaching and in the carbonated residue from the flotation of the anomaly 13 ore. The results indicate the feasibility of treating the waste of the heap leaching through dynamic leaching. The study of the uranium leaching from the flotation residue through acid leaching technique indicated a recovery of 96% of uranium, however with a high consumption of acid, around 450 kg/t, showing that for this case, the most suitable technique for the process is alkaline leaching. (author)

Ionic flotation of uranium contained in industrial phosphoric acid

International Nuclear Information System (INIS)

Jdid; Blazy; Bessiere

1983-01-01

A new process for uranium recovery from industrial phosphoric acid at 30% of P 2 O 5 is applied by the ionic flotation process. Research is carried out on determination of the nature of ionic species of U in H 3 PO 4 5.5 M and the behavior of reagents from CECA Co. in very acid media. Reagents able to form complexes directly with uranium and stable in phosphoric acid selected are: potassium ethylene diamine tetra (methylene phosphonate) (INIPOL AD32) and sodium dialkyldiphosphonate (34S). Uranium IV, obtained by reduction of uranium VI with iron powder, is precipitated by these reagents. Flotation of the precipitate obtained with INIPOL AD 32 is realized by addition of hexylamino bis (methylene phosphonic acid). A recovery of 80 wt% is obtained. Flotation of the coprecipitate 34S-U(IV) is obtained without any other additions because 34S is a surfactant. Metal recovery is better than 90% and the coprecipitate contains more than 10% U. The process is fast precipitation 10 minutes and flotation 5 minutes and is efficient even at 60 0 C [fr

Effect of pH on Pulp Potential and Sulphide Mineral Flotation

OpenAIRE

GÖKTEPE, Ferihan

2014-01-01

Control of pH is one of the most widely applied methods for the modulation of mineral flotation. In this study the effect of pH on potential in solution and sulphur minerals flotation is discussed with various electrodes. The electrodes were platinum, gold, chalcopyrite, pyrite and galena. In solution, potentials were linearly dependent on pH with a different slope for each electrode. Chalcopyrite, pyrite, sphalerite and galena minerals flotation tests were performed in a microflot...

Removal of adsorbent particles od copper ions by Jet flotation

International Nuclear Information System (INIS)

Santander, M.; Tapia, P.; Pavez, O.; Valderrama, L.; Guzman, D.

2009-01-01

The present study shows the results obtained on the removal of copper ions from synthetic effluents by using the adsorbent particles flotation technique (APF) in a Jet flotation cell (Jameson type). In a typical experimental run, a mineral with high quartz content was used as adsorbent particles in the adsorption and flotation experiments, to determine optimal pH conditions, adsorbent particles concentration; flotation reagents dosage and air/effluent flow ratio for applying in the Jet cell to maximize the efficiency of copper ions adsorptions and the removal of particles adsorbents containing the absorbed copper ions. The results indicate the at pH>7 and at adsorbent particles concentration of 2 kg.m - 3, 99% of copper ions is adsorbed and, when the air/effluent flow ratio applied in the Jet cell is 0,2, 98% of absorbent particles containing the adsorbed copper ions is removed. (Author) 39 refs.

Simulation optimisation

International Nuclear Information System (INIS)

Anon

2010-01-01

Over the past decade there has been a significant advance in flotation circuit optimisation through performance benchmarking using metallurgical modelling and steady-state computer simulation. This benchmarking includes traditional measures, such as grade and recovery, as well as new flotation measures, such as ore floatability, bubble surface area flux and froth recovery. To further this optimisation, Outotec has released its HSC Chemistry software with simulation modules. The flotation model developed by the AMIRA P9 Project, of which Outotec is a sponsor, is regarded by industry as the most suitable flotation model to use for circuit optimisation. This model incorporates ore floatability with flotation cell pulp and froth parameters, residence time, entrainment and water recovery. Outotec's HSC Sim enables you to simulate mineral processes in different levels, from comminution circuits with sizes and no composition, through to flotation processes with minerals by size by floatability components, to full processes with true particles with MLA data.

Coal Recycling from Tailings using Flotation with 2-Level Experimental Design Techniques

Directory of Open Access Journals (Sweden)

Sajjad Jannesar Malakooti

2012-12-01

Full Text Available In this study, the possibility of producing coal with less than 11% ash from tailings of flotation process was investigated. The effect of six flotation parameters: collector type, collector consumption, frother type, frother consumption, pulp density and mixing rate were studied on a sample from a tailing dam. A software based experimental design approach (DX7 was applied to determine and model effective parameters as well as flotation optimization through fractional factorial. It was shown that collector type and flotation machine mixing rate were the most effective parameters on ash content of concentrate. The results indicated that the production of a desired ash content concentrate, i.e.

Distribution of the ore elements in ore bodies of the Zapolyarnoe field (Kola Peninsula

Directory of Open Access Journals (Sweden)

D. V. Taymasov

2017-12-01

Full Text Available The author conducted studies of the chemical zonality of ore deposits of all types for the sulfide-copper-nickel deposit Zapolyarnoe. Within the deposit of sulfide-copper-nickel ores Zapolyarnoe are the following industrial types of ores: rich interspersed ores, which are interspersed mineralization in peridotites; brecciated ores formed by detrital material; poor interspersed ores characterized by vein-interspersed mineralization; solid ores in a form of massive sulphide emissions. This work is based on operational and detailed exploration data. The author sorted samples according to the types of ores. Using the results, the author derived regression lines and their formulas to rectilinear dependencies. Analysis of the graphs showed that for all types of ores the dependences of copper and cobalt content on nickel content are direct, but at that, in thick-interspersed and brecciated types they are similar, and in scattered-interspersed they differ significantly. It becomes clear that correlation of copper and nickel in ore body depends on the scattered-interspersed ores, whereas the correlation of cobalt and nickel is determined mainly by thick-interspersed and brecciated ores. Dependencies between nickel, copper and cobalt in ores change when concentration of nickel in the ore changes. The graphs also show that the ratio of Ni/Cu in breccias and scattered-interspersed ores, as well as in near-ore metaperidotites, is almost constant at different nickel concentrations, on average 2:1.5 and 1, respectively. Thick- interspersed ores show the tendency towards an increase in the ratio with an increase in nickel content. The Ni/Co ratio increases with an increase of Ni concentration in all types of ores. In rich ores, growth occurs along a stepped curve, and in breccias – rectilinearly. Thus, the analysis of distribution of ore elements in ore bodies indicates a complex heterogeneous composition of sulphide mineralizations in different types of ores

Flotation separation of PET from a PET, PVC and PS mixture by the hydrofilization of the PET surface in NaOH solutions

Directory of Open Access Journals (Sweden)

Ľubica Kozáková

2005-11-01

Full Text Available Recycling is the most effective method of waste minimization created by the human activity. The idea of waste re-use as a result of environmental, social and economical factors is becoming very relevant in the last decades. The portion of plastics in the municipal waste is growing year by year as also is its use in the wrapping industry. A condition for recycling technologies is the input of highly pure plastics (without undesirable admixtures suitable for recycling. Various separation technologies can be used which provide separation of particular components of plastic waste and contaminants. Flotation is one of the separation methods used especially for the ore beneficiation but recently is widely also used for the separation of various types of waste. Plastics, which are not possible to be separated by gravitational methods (because they have almost the same density, PET from beverage bottles, PVC from bottles and foils and PS from beverage beakers, were studied. By changing the surface properties of PET from naturally hydrophobic to hydrophilic by the adjustment in a NaOH solution, PET with the recovery of up to 99 % in the non-foamy product and with the product purity of up to 98 % was acquired by the flotation.

Effect of mechanical and chemical clay removals by hydrocyclone and dispersants on coal flotation

Energy Technology Data Exchange (ETDEWEB)

Oats, W.J.; Ozdemir, O.; Nguyen, A.V. [University of Queensland, Brisbane, Qld. (Australia). School of Chemical Engineering

2010-04-15

Fine minerals, mostly clays, are known to have a detrimental effect on coal flotation. This paper focuses on the effect of mechanical and chemical removals of fine minerals by hydrocyclone and dispersants on coal flotation. The experimental results showed that the flotation recovery slightly increased from medium acidic to medium alkaline ranges. The flotation experiments carried out with dispersants at different dosages showed that the dispersants did not enhance the flotation recovery significantly. However, the removal of the fine fraction from the feed using a hydrocyclone significantly increased the flotation recovery. The bubble-particle attachment tests also indicated that the attachment time between an air bubble and the coal particles increased in the presence of clay particles. These attachment time results clearly showed that the clay particles adversely affected the flotation of coal particles by covering the coal surfaces which reduced the efficiency of bubble-coal attachment. An analysis based on the colloid stability theory showed that the clay coating was governed by the van der Waals attraction and that the double-layer interaction played a secondary role. It was also concluded that the best way to increase the flotation recovery in the presence of clays was to remove these fine minerals by mechanical means such as hydrocylones.

Zeta potentials in the flotation of oxide and silicate minerals.

Science.gov (United States)

Fuerstenau, D W; Pradip

2005-06-30

Adsorption of collectors and modifying reagents in the flotation of oxide and silicate minerals is controlled by the electrical double layer at the mineral-water interface. In systems where the collector is physically adsorbed, flotation with anionic or cationic collectors depends on the mineral surface being charged oppositely. Adjusting the pH of the system can enhance or prevent the flotation of a mineral. Thus, the point of zero charge (PZC) of the mineral is the most important property of a mineral in such systems. The length of the hydrocarbon chain of the collector is important because of chain-chain association enhances the adsorption once the surfactant ions aggregate to form hemimicelles at the surface. Strongly chemisorbing collectors are able to induce flotation even when collector and the mineral surface are charged similarly, but raising the pH sufficiently above the PZC can repel chemisorbing collectors from the mineral surface. Zeta potentials can be used to delineate interfacial phenomena in these various systems.

Removal of arsenopyrite from complex sulfide minerals by froth flotation

Science.gov (United States)

Choi, Jin-young; Kim, Yang-soo; Kim, Dong-gyu; Han, Oh-hyung; Park, Chul-hyun

2016-04-01

Arsenic (As) is one of hazardous materials and a penalty element in metal concentrates and so metal concentrates containing arsenic of over 0.5% has been currently restricted in import and export trade. It also corrodes a smelting furnace as well as shortens its life cycle. In korea, Janggun mine that produces galena (PbS) /sphalerite (ZnS) concentrate containing arsenic of 1.78% charges a penalty of US 2/ton to LS-Nikko smelter. Hence in this work, flotation tests for removal of arsenopyrite (FeAsS) from sulfide mineral concentrates were carried out using lab scale flotation cell, which maintain grade and recovery of PbS and ZnS in comparison to flotation plant. Particularly, this study was focused on investigating the combination of several chemical reagents (depressant, collector, activator and etc.) that affect flotation performance. In the straight differential flotation for PbS, a PbS grade of 75.80% and a recovery of 90.12% could be obtained with FeAsS removal of 84.1% (0.2% As) under the conditions of 20% feed solids concentration, pH 8.5, 50g/t frother (AF65), 40g/t collector (AP242) and 800g/t As depressant (NaHSO3) and 600g/t Zn depressant (ZnSO4). In the ZnS flotation, the maximum separation achievable for ZnS using froth flotation has been shown to be a grade of 72.57% and a recovery of 95.43%. At this time, FeAsS removal of 87.8% (0.16% As) could be successfully accomplished under pH 11, and 800g/t Zn activator (CuSO4), 75g/t frother (AF65), 60g/t collector (AP211) and 600g/t As depressant (NaHSO3). Acknowledgments This work was supported by the Energy and Resources Engineering Program Grant funded by the Ministry of Trade, Industry and Energy, Korea

Uranium ores

International Nuclear Information System (INIS)

Poty, B.; Roux, J.

1998-01-01

The processing of uranium ores for uranium extraction and concentration is not much different than the processing of other metallic ores. However, thanks to its radioactive property, the prospecting of uranium ores can be performed using geophysical methods. Surface and sub-surface detection methods are a combination of radioactive measurement methods (radium, radon etc..) and classical mining and petroleum prospecting methods. Worldwide uranium prospecting has been more or less active during the last 50 years, but the rise of raw material and energy prices between 1970 and 1980 has incited several countries to develop their nuclear industry in order to diversify their resources and improve their energy independence. The result is a considerable increase of nuclear fuels demand between 1980 and 1990. This paper describes successively: the uranium prospecting methods (direct, indirect and methodology), the uranium deposits (economical definition, uranium ores, and deposits), the exploitation of uranium ores (use of radioactivity, radioprotection, effluents), the worldwide uranium resources (definition of the different categories and present day state of worldwide resources). (J.S.)

Contribution to the study of xenotime and zircon flotation

International Nuclear Information System (INIS)

Scorzeli, Isabella Bernstein; Torem, Mauricio Leonardo

1995-01-01

Flotation and electrokinetics behaviour have studied with xenotime (YPO 4 ) and zircon (Zr Si O 4 ) from a mixture of grains with 90% xenotime and 10% zircon, produced in cassiterite concentration process. Micro flotation and zeta potential have been also studied, by using oleic acid P.A. and DP1-6256 as collectors, and sodium metasillicate and Procol DA911 as modifier agents

Switching and optimizing control for coal flotation process based on a hybrid model

Science.gov (United States)

Dong, Zhiyong; Wang, Ranfeng; Fan, Minqiang; Fu, Xiang

2017-01-01

Flotation is an important part of coal preparation, and the flotation column is widely applied as efficient flotation equipment. This process is complex and affected by many factors, with the froth depth and reagent dosage being two of the most important and frequently manipulated variables. This paper proposes a new method of switching and optimizing control for the coal flotation process. A hybrid model is built and evaluated using industrial data. First, wavelet analysis and principal component analysis (PCA) are applied for signal pre-processing. Second, a control model for optimizing the set point of the froth depth is constructed based on fuzzy control, and a control model is designed to optimize the reagent dosages based on expert system. Finally, the least squares-support vector machine (LS-SVM) is used to identify the operating conditions of the flotation process and to select one of the two models (froth depth or reagent dosage) for subsequent operation according to the condition parameters. The hybrid model is developed and evaluated on an industrial coal flotation column and exhibits satisfactory performance. PMID:29040305

Flotation separation of strontium via phosphate precipitation.

Science.gov (United States)

Thanh, Luong H V; Liu, J C

2017-06-01

Flotation separation of strontium (Sr) from wastewater via phosphate precipitation was investigated. While 37.33% of Sr precipitated at highly alkaline pH in the absence of PO 4 3- , it completely precipitated as Sr 3 (PO 4 ) 2 at a molar ratio ([PO 4 3- ]:[Sr 2+ ]) of 0.62 at a lower pH value. The presence of Ca 2+ hindered Sr precipitation, yet it could be overcome by increasing the PO 4 3- dose. Sodium dodecyl sulfate (SDS) was a better collector for dispersed air flotation of Sr 3 (PO 4 ) 2 than cetyl trimethyl ammonium bromide, or mixed collector systems of SDS and saponin. The highest separation efficiency of 97.5% was achieved at an SDS dose of 40 mg/L. The main mechanism in the precipitate flotation is adsorption of anionic SDS on the positively charged surface of colloidal Sr 3 (PO 4 ) 2 via electrostatic interaction. SDS enhanced the aggregation of Sr 3 (PO 4 ) 2 precipitates as the size increased from 1.65 to 28.0 μm, which was beneficial to separation as well.

Selective detachment process in column flotation froth

Energy Technology Data Exchange (ETDEWEB)

Honaker, R.Q.; Ozsever, A.V.; Parekh, B.K. [University of Kentucky, Lexington, KY (United States). Dept. of Mining Engineering

2006-05-15

The selectivity in flotation columns involving the separation of particles of varying degrees of floatability is based on differential flotation rates in the collection zone, reflux action between the froth and collection zones, and differential detachment rates in the froth zone. Using well-known theoretical models describing the separation process and experimental data, froth zone and overall flotation recovery values were quantified for particles in an anthracite coal that have a wide range of floatability potential. For highly floatable particles, froth recovery had a very minimal impact on overall recovery while the recovery of weakly floatable material was decreased substantially by reductions in froth recovery values. In addition, under carrying-capacity limiting conditions, selectivity was enhanced by the preferential detachment of the weakly floatable material. Based on this concept, highly floatable material was added directly into the froth zone when treating the anthracite coal. The enriched froth phase reduced the product ash content of the anthracite product by five absolute percentage points while maintaining a constant recovery value.

Chelation and flotation in endodontic practice: an update.

Science.gov (United States)

Stewart, G G

1986-10-01

The removal of broken instruments and silver points, as well as pulp tissue, may be accomplished by careful instrumentation, irrigation, and flotation. Flotation and recapitulation with smaller instruments and irrigation with copious amounts of sodium hypochlorite can clean out microorganisms and the organic matter from the tubular structure which provides a more ideal surface for sealing the root canal system. A sterile environment was obtained by removing the substrate and creating a more ideal environment for better healing.

Potential controlled flotation of Sarcheshmeh Molybdenite

International Nuclear Information System (INIS)

Kolahdoozan, M.; Noori, H.

2007-01-01

Molybdenite flotation in the Sarcheshmeh Copper Complex was studied as a function of pulp potential, controlled using two types of sodium sulfide, a mineral origin and a chemical nature. Air and either plant or laboratory nitrogen were used as flotation careers. Potential readings took place in rougher cells, as it was proved to be vital in the molybdenite circuit. Results showed that, at reducing potentials between -525 and -575 mv, the highest molybdenum recovery of 93% and the lowest copper recovery of 4-15% can be achieved. These potentials did not change considerably by adding extra amounts of sodium sulfide. At more oxidizing potentials, i.e. more than -450 mv, copper recovery increases while the recovery of Molybdenite drops

Semi-industrial experimental study on bauxite separation using a cell-column integration process

Science.gov (United States)

Zhang, Ning-ning; Zhou, Chang-chun; Cong, Long-fei; Cao, Wen-long; Zhou, You

2016-01-01

The cyclonic-static micro-bubble flotation column (FCSMC) is a highly efficient mineral processing equipment. In this study, a cell-column (FCSMC) integration process was investigated for the separation of bauxite and its feasibility was analyzed on a theoretical basis. The properties of low-grade bauxite ore from Henan Province, China were analyzed. Parameters such as reagent dosage, scraping bubble time, and pressure of the circulating pump during the sorting process were investigated and optimized to improve the flotation efficiency. On the basis of these parameters, continuous separation experiments were conducted. Bauxite concentrate with an aluminum-to-silicon (A/S) mass ratio of 6.37 and a 77.63wt% recovery rate were achieved via a flow sheet consisting of "fast flotation using a flotation cell, one roughing flotation and one cleaning flotation using flotation columns". Compared with the full-flotation-cells process, the cell-column integration process resulted in an increase of the A/S ratio by 0.41 and the recovery rate by 17.58wt%. Cell-column integration separation technology represents a new approach for the separation of middle-to-low-grade bauxite ore.

Effect of three typical sulfide mineral flotation collectors on soil microbial activity.

Science.gov (United States)

Guo, Zunwei; Yao, Jun; Wang, Fei; Yuan, Zhimin; Bararunyeretse, P; Zhao, Yue

2016-04-01

The sulfide mineral flotation collectors are wildly used in China, whereas their toxic effect on soil microbial activity remains largely unexplored. In this study, isothermal microcalorimetric technique and soil enzyme assay techniques were employed to investigate the toxic effect of typical sulfide mineral flotation collectors on soil microbial activity. Soil samples were treated with different concentrations (0-100 μg•g - 1 soil) of butyl xanthate, butyl dithiophosphate, and sodium diethyldithiocarbamate. Results showed a significant adverse effect of butyl xanthate (p flotation collectors concentration from 20.0 to 100.0 μg•g(-1). However, the adverse effects of these three floatation collectors showed significant difference. The IC 20 of the investigated flotation reagents followed such an order: IC 20 (butyl xanthate) > IC 20 (sodium diethyldithiocarbamate) > IC 20 (butyl dithiophosphate) with their respective inhibitory concentration as 47.03, 38.36, and 33.34 μg•g(-1). Besides, soil enzyme activities revealed that these three flotation collectors had an obvious effect on fluorescein diacetate hydrolysis (FDA) enzyme and catalase (CAT) enzyme. The proposed methods can provide meaningful toxicological information of flotation reagents to soil microbes in the view of metabolism and biochemistry, which are consistent and correlated to each other.

Study of flotation performance of kerosene after ultrasonic emulsified

Energy Technology Data Exchange (ETDEWEB)

Kang Wen-ze; Wang Hui; Kong Xiao-hong; Lu Yu-ting; Hu Jung [Heilongjiang Institute of Science and Technology, Harbin (China). School of Resource and Environmental Engineering

2008-01-15

A Setaram calorimeter, a contact angle gauge DCAT21, surface tension apparatus and a Leica electron microscope were used to study the nature of emulsified kerosene and kerosene and their effects on slime. Batch flotation tests were carried out. The results show that the particle diameter of emulsified kerosene, the dispersibility in water, the wetting heat with slime, changing contact angle and decreasing gas-solution interfacial tension are all better than those of kerosene. The consumption of emulsified kerosene is only one third of that of kerosene when equivalent yields of clean coal are obtained. The flotation speed of emulsified kerosene is faster than that of kerosene. The yield of clean coal with emulsified kerosene is higher than that of kerosene by 7.38% and the ash content of clean coal emulsified in kerosene is lower than that of kerosene by 0.98% when equivalent amounts of the two reagents are used in the flotation process. The study shows that flotation selectivity and efficiency of emulsified kerosene are all higher than those of kerosene and the consumption of reagent is lower than that of kerosene. 15 refs., 3 figs., 5 tabs.

Ammonia modification for flotation separation of polycarbonate and polystyrene waste plastics.

Science.gov (United States)

Wang, Chong-Qing; Wang, Hui; Gu, Guo-Hua; Lin, Qing-Quan; Zhang, Ling-Ling; Huang, Luo-Luo; Zhao, Jun-Yao

2016-05-01

A promising method, ammonia modification, was developed for flotation separation of polycarbonate (PC) and polystyrene (PS) waste plastics. Ammonia modification has little effect on flotation behavior of PS, while it changes significantly that of PC. The PC recovery in the floated product drops from 100% to 3.17% when modification time is 13min and then rises to 100% after longer modification. The mechanism of ammonia modification was studied by contact angle, and Fourier transform infrared (FT-IR) and X-ray photoelectron spectroscopy (XPS) measurements. Contact angle of PC indicates the decline of PC recovery in the floated product is ascribed to an increase in surface wettability. FT-IR and XPS spectra suggest that ammonia modification causes chemical reactions occurred on PC surface. Flotation behavior of ammonia-modified PC and PS was investigated with respect to flotation time, frother concentration and particle sizes. Flotation separation of PC and PS waste plastics was conducted based on the flotation behavior of single plastic. PC and PS mixtures with different particle sizes are separated efficiently, implying that the technology possesses superior applicability to particle sizes of plastics. The purity of PS and PC is up to 99.53% and 98.21%, respectively, and the recovery of PS and PC is larger than 92.06%. A reliable, cheap and effective process is proposed for separation of PC and PS waste plastics. Copyright © 2016 Elsevier Ltd. All rights reserved.

Artificial reefs and reef restoration in the Laurentian Great Lakes

Science.gov (United States)

McLean, Matthew W.; Roseman, Edward; Pritt, Jeremy J.; Kennedy, Gregory W.; Manny, Bruce A.

2015-01-01

We reviewed the published literature to provide an inventory of Laurentian Great Lakes artificial reef projects and their purposes. We also sought to characterize physical and biological monitoring for artificial reef projects in the Great Lakes and determine the success of artificial reefs in meeting project objectives. We found records of 6 artificial reefs in Lake Erie, 8 in Lake Michigan, 3 in Lakes Huron and Ontario, and 2 in Lake Superior. We found 9 reefs in Great Lakes connecting channels and 6 reefs in Great Lakes tributaries. Objectives of artificial reef creation have included reducing impacts of currents and waves, providing safe harbors, improving sport-fishing opportunities, and enhancing/restoring fish spawning habitats. Most reefs in the lakes themselves were incidental (not created purposely for fish habitat) or built to improve local sport fishing, whereas reefs in tributaries and connecting channels were more frequently built to benefit fish spawning. Levels of assessment of reef performance varied; but long-term monitoring was uncommon as was assessment of physical attributes. Artificial reefs were often successful at attracting recreational species and spawning fish; however, population-level benefits of artificial reefs are unclear. Stressors such as sedimentation and bio-fouling can limit the effectiveness of artificial reefs as spawning enhancement tools. Our investigation underscores the need to develop standard protocols for monitoring the biological and physical attributes of artificial structures. Further, long-term monitoring is needed to assess the benefits of artificial reefs to fish populations and inform future artificial reef projects.

Dissolved Air Flotation of arsenic adsorbent particles

Directory of Open Access Journals (Sweden)

Mario Enrique Santander Muñoz

2015-01-01

Full Text Available The removal of arsenic from synthetic effluent was studied using the adsorbent particle flotation technique (APF and dissolved air flotation (DAF. A sample of an iron mineral was used as adsorbent particles of arsenic, ferric chloride as coagulant, cationic poly-acrylamide (NALCO 9808 as flocculants, and sodium oleate as collector. Adsorption studies to determine the pH influence, contact time, and adsorbent particles concentration on the adsorption of arsenic were carried out along with flotation studies to determine the removal efficiency of adsorbents particles. The results achieved indicate that the adsorption kinetic of arsenic is very rapid and that in range of pH’s from 2 to 7 the adsorption percentages remain constant. The equilibrium conditions were achieved in 60 minutes and about 95% of arsenic was adsorbed when used an adsorbent concentration of 2 g/L and pH 6.3. The maximum adsorption capacity of adsorbent particles was 4.96 mg/g. The mean free energy of adsorption (E was found to be 2.63 kJ/mol, which suggests physisorption. The results of the flotation studies demonstrated that when synthetic effluents with 8.9 mg/L of arsenic were treated under the following experimental conditions; 2 g/L of adsorbent particles, 120 mg/L of Fe(III, 2 mg/L of Nalco 9808, 20 mg/L of sodium oleate, and 40% of recycle ratio in the DAF, it was possible to reach 98% of arsenic removal and 6.3 NTU of residual turbidity in clarified synthetic effluent.

Digital reef rugosity estimates coral reef habitat complexity.

Science.gov (United States)

Dustan, Phillip; Doherty, Orla; Pardede, Shinta

2013-01-01

Ecological habitats with greater structural complexity contain more species due to increased niche diversity. This is especially apparent on coral reefs where individual coral colonies aggregate to give a reef its morphology, species zonation, and three dimensionality. Structural complexity is classically measured with a reef rugosity index, which is the ratio of a straight line transect to the distance a flexible chain of equal length travels when draped over the reef substrate; yet, other techniques from visual categories to remote sensing have been used to characterize structural complexity at scales from microhabitats to reefscapes. Reef-scale methods either lack quantitative precision or are too time consuming to be routinely practical, while remotely sensed indices are mismatched to the finer scale morphology of coral colonies and reef habitats. In this communication a new digital technique, Digital Reef Rugosity (DRR) is described which utilizes a self-contained water level gauge enabling a diver to quickly and accurately characterize rugosity with non-invasive millimeter scale measurements of coral reef surface height at decimeter intervals along meter scale transects. The precise measurements require very little post-processing and are easily imported into a spreadsheet for statistical analyses and modeling. To assess its applicability we investigated the relationship between DRR and fish community structure at four coral reef sites on Menjangan Island off the northwest corner of Bali, Indonesia and one on mainland Bali to the west of Menjangan Island; our findings show a positive relationship between DRR and fish diversity. Since structural complexity drives key ecological processes on coral reefs, we consider that DRR may become a useful quantitative community-level descriptor to characterize reef complexity.

Tracer studies of flotation in the laboratory and in mineral processing plant

International Nuclear Information System (INIS)

Niemi, A.J.; Thereska, J.; Plasari, E.; Kacaj, M.

1993-01-01

Radioisotope tracers have a proven application for the extraction of residence time distributions and the evaluation of flotation rates in industry. This paper shows how values of the rate factor k are scaled up on the basis of flotation in the laboratory and tracer tests in plant. The procedure is illustrated by a theoretical study and by experimental data. The information obtained can be introduced into models of larger flotation systems. (author)

Effect of microwave radiation on coal flotation

Energy Technology Data Exchange (ETDEWEB)

Ozbayoglu, G.; Depci, T.; Ataman, N. [Middle East Technical University, Ankara (Turkey). Mining Engineering Department

2009-07-01

Most low-rank coals are high in moisture and acid functional groups, therefore showing poor floatability. Drying, which removes the water molecules trapped in the pores and adsorbed at the surface of coal, decreases the hydrophilic character and improves the floatability. Microwave heating, whose simplest application is drying, was applied at 0.9 kW power level for 60 sec exposure time in the experiments to decrease the moisture content of coal in order to enhance the hydrophobicity. The flotation tests of microwave-treated coal by using heptanol and octanol lead to a higher flotation yield and ash removal than original coal.

Recent trends in research and development work on the processing of uranium ore in South Africa

International Nuclear Information System (INIS)

James, H.E.

1976-01-01

The rapid increases in the price of gold and uranium in recent years have coincided with an unprecedented increase in working costs at South African gold mines. A re-examination of the existing flowsheets for the recovery of uranium, gold and pyrite from Witwatersrand ores, in the light of these economic trends, has resulted in the identification of a number of profitable areas for research and development. The main topics under investigation in South Africa in the processing of uranium ore are the use of physical methods of concentration such as flotation, gravity concentration and wet high-intensity magnetic separation; the wider adoption of the 'reverse leach', in which prior acid leaching for uranium improves the subsequent extraction of gold; the use of higher leaching temperatures and higher concentrations of ferric ion in the leach to increase the percentage of uranium extracted, including the production of ferric ion from recycled solutions; the application of pressure leaching to the recovery of uranium from low-grade ores and concentrates; the development of a continuous ion-exchange contactor capable of handling dilute slurries, so that simpler and cheaper techniques of solid/liquid separation can be used instead of the expensive filtration and clarification steps, and the improvement of instrumentation for the control of additions of sulphuric acid and manganese dioxide to the leach. A brief description is given of the essential features of the new or improved processing techniques under development that hold promise of full-scale application at existing or future uranium plants

Recent trends in research and development work on the processing of uranium ore in South Africa

International Nuclear Information System (INIS)

James, H.E.

1976-07-01

The rapid increases in the price of gold and uranium in recent years have coincided with an unprecedented increase in working costs at South African gold mines. A re-examination of the existing flowsheets for the recovery of uranium, gold, and pyrite from Witwatersrand ores, in the light of these economic trends, has resulted in the identification of a number of profitable areas for research and development. The main topics under investigation in South Africa in the processing of uranium ore are the use of physical methods of concentration such as flotation, gravity concentration, and wet high-intensity magnetic separation; the wider adoption of the 'reverse leach', in which prior acid leaching for uranium improves the subsequent extraction of gold; the use of higher leaching temperatures and higher concentrations of ferric ion in the leach to increase the percentage of uranium extracted, including the production of ferric ion from recycled solutions; the application of pressure leaching to the recovery of uranium from low-grade ores and concentrates; the development of a continuous ion-exchange contactor capable of handling dilute slurries, so that simpler and cheaper techniques of solid-liquid separation can be used instead of the expensive filtration and clarification steps, and the improvement of instrumentation for the control of additions of sulphuric acid and manganese dioxide to the leach. A brief description is given of the essential features of the new or improved processing techniques under development that hold promise of full-scale application at existing or future uranium plants [af

Selective separation of Cu, Zn, and As from solution by flotation techniques

International Nuclear Information System (INIS)

Stalidis, G.A.; Matis, K.A.; Lazaridis, N.K.

1989-01-01

The selective precipitation and flotation of copper, zinc, and arsenic ions from dilute aqueous solutions were investigated. Phase separation was accomplished effectively by the dissolved-air technique for the production of fine gas bubbles, and a short-chain xanthate was applied as the collector for copper ions, dialkyl-dithiocarbamate for zinc, and ferric sulfate for the pentavalent arsenic. The procedures followed were ion flotation for copper and zinc, and adsorbing colloid flotation for arsenic (without a surfactant)

Study on the determination of ore-formation age of primary gold ore

International Nuclear Information System (INIS)

Ying Junlong; Zhao Puyun; Guo Hong

1997-01-01

The accurate determination of gold ore-formation age and ore-source isotope composition are of important significance in the research on gold geology and prospecting. According to the summary of three year indoor and field work, the ore-formation ages and isotope compositions of some typical gold deposits were obtained: The age of gold ore of the Wuhuaaobao deposit in geo-syncline region north to the north margin of North-China paleo-land is 130-120 Ma corresponding to the Late-orogenic stage. The ore-formation age of the Saiwusu gold deposit in the southern platform region is 211 +- 15 Ma, recycling reworking of the old-land. The Hougou-Huangtuliang gold deposit located in the middle of the platform region is 243 +- 7 Ma old attributed to the regeneration ore-formation on the old-land. the age of Jiaojia-Rushan gold deposit in Eastern Shandong is 122.7 +- 3.4 Ma and 128 +- 23 Ma belonging to Yanshanian stage. The Babaoshan gold-silver deposit in Cathaysian old-land is 140 +- 5 Ma old originated from volcanic hydrothermal ore-formation

Flotation of copper-bearing shale in solutions of inorganic salts and organic reagents

Directory of Open Access Journals (Sweden)

Ratajczak Tomasz

2017-01-01

Full Text Available Flotation data on copper-bearing shale in aqueous solutions of inorganic electrolytes (NaCl, Na2SO4, KPF6, NH4Cl and organic reagents (ethylamine, propylamine as frothers were presented and discussed. The relationships between shale flotation, surface tension of aqueous solution and foam height during bubbling with air in the flotation system were presented. It has been found that flotation of shale in the presence of inorganic salts the yield was directly proportional to the surface tension of the aqueous solution of salt and inversely proportional to the height of the foam. On the other hand, for organic reagents solutions (short chain amines, a reverse effect has been observed in relation to the inorganic compounds studied, that is the yield of copper-bearing shale flotation and the foam height were inversely proportional to the surface tension of the amine solution.

Use of adsorption colloidal flotation for sea water microelement extraction

International Nuclear Information System (INIS)

Zhorov, V.A.; Barannik, V.P.; Lyashenko, S.V.; Kirchanova, A.I.; Kobylyanskaya, A.G.

1976-01-01

The colloidal flotation is studied of copper, molybdenum and uranium from sea water, a hydrated iron oxide being used as a sorbent. Used as particle collectors are octadecanoic and indolyloleic acids, and as foamers-''Stearox 6''. Optimal conditions for the separation of copper, uranium and molybdenum from sea water have been found. The sorption isotherm equation is shown as being suitable for the description of the flotation process as regards these elements. The colloidal flotation process for the case under study is shown to obey the law of mass action in the pH range 0.5 to 0.7 and on the sorbent mass variation from 0.1 to 5.0 mg

Adsorption of sulfide ions on cerussite surfaces and implications for flotation

International Nuclear Information System (INIS)

Feng, Qicheng; Wen, Shuming; Zhao, Wenjuan; Deng, Jiushuai; Xian, Yongjun

2016-01-01

Highlights: • A new discussion on the lead sulfide species is introduced. • The Na_2S concentration determines cerussite sulfidization. • The activity of lead sulfide species also determines cerussite sulfidization. • Disulfide and polysulfide in lead sulfide species affect its activity. - Abstract: The adsorption of sulfide ions on cerussite surfaces and implications for flotation were studied by X-ray photoelectron spectroscopy (XPS) analysis, micro-flotation tests, and surface adsorption experiments. The XPS analysis results indicated that lead sulfide species formed on the mineral surface after treatment by Na_2S, and the increase in the Na_2S concentration was beneficial for sulfidization. In addition to the content of lead sulfide species, its activity, which was determined by the proportion of sulfide, disulfide and polysulfide, also played an important role in cerussite sulfidization. Micro-flotation tests results demonstrated that insufficient or excessive addition of Na_2S in pulp solutions has detrimental effects on flotation performance, which was attributed to the dosage of Na_2S and the activity of lead sulfide species formed on the mineral surface. Surface adsorption experiments of sulfide ions determined the residual S concentrations in pulp solutions and provided a quantitative illustration for the inhibition of cerussite flotation by excessive sulfide ions. Moreover, it also revealed that sulfide ions in the pulp solution were transformed onto the mineral surface and formed lead sulfide species. These results showed that both of lead sulfide species and its activity acted as an important role in sulfidization flotation process of cerussite.

Adsorption of sulfide ions on cerussite surfaces and implications for flotation

Energy Technology Data Exchange (ETDEWEB)

Feng, Qicheng [State Key Laboratory of Complex Nonferrous Metal Resources Clean Utilization, Kunming University of Science and Technology, Kunming 650093 (China); Faculty of Land Resource Engineering, Kunming University of Science and Technology, Kunming 650093 (China); Wen, Shuming, E-mail: fqckmust@126.com [State Key Laboratory of Complex Nonferrous Metal Resources Clean Utilization, Kunming University of Science and Technology, Kunming 650093 (China); Faculty of Land Resource Engineering, Kunming University of Science and Technology, Kunming 650093 (China); Zhao, Wenjuan [Kunming Metallurgical Research Institute, Kunming 650031 (China); Deng, Jiushuai; Xian, Yongjun [State Key Laboratory of Complex Nonferrous Metal Resources Clean Utilization, Kunming University of Science and Technology, Kunming 650093 (China); Faculty of Land Resource Engineering, Kunming University of Science and Technology, Kunming 650093 (China)

2016-01-01

Highlights: • A new discussion on the lead sulfide species is introduced. • The Na{sub 2}S concentration determines cerussite sulfidization. • The activity of lead sulfide species also determines cerussite sulfidization. • Disulfide and polysulfide in lead sulfide species affect its activity. - Abstract: The adsorption of sulfide ions on cerussite surfaces and implications for flotation were studied by X-ray photoelectron spectroscopy (XPS) analysis, micro-flotation tests, and surface adsorption experiments. The XPS analysis results indicated that lead sulfide species formed on the mineral surface after treatment by Na{sub 2}S, and the increase in the Na{sub 2}S concentration was beneficial for sulfidization. In addition to the content of lead sulfide species, its activity, which was determined by the proportion of sulfide, disulfide and polysulfide, also played an important role in cerussite sulfidization. Micro-flotation tests results demonstrated that insufficient or excessive addition of Na{sub 2}S in pulp solutions has detrimental effects on flotation performance, which was attributed to the dosage of Na{sub 2}S and the activity of lead sulfide species formed on the mineral surface. Surface adsorption experiments of sulfide ions determined the residual S concentrations in pulp solutions and provided a quantitative illustration for the inhibition of cerussite flotation by excessive sulfide ions. Moreover, it also revealed that sulfide ions in the pulp solution were transformed onto the mineral surface and formed lead sulfide species. These results showed that both of lead sulfide species and its activity acted as an important role in sulfidization flotation process of cerussite.

Effects of Metal Ions on the Flotation of Apatite, Dolomite and Quartz

Directory of Open Access Journals (Sweden)

Yaoyang Ruan

2018-04-01

Full Text Available The effects of Ca2+, Mg2+, Al3+, and Fe3+ on the flotation behaviors of apatite, dolomite and quartz were investigated through a micro-flotation test, and the influence of calcium ions on the flotation of these minerals was further elucidated by solution chemistry study, zeta potential measurement, and X-ray photoelectron spectroscopy (XPS analyses. The results indicate that an appropriate amount of Ca2+ and Mg2+ can improve the floatability of apatite but had a negligible effect on the flotation performance of dolomite, whereas Al3+, Fe3+, and excessive amounts of Ca2+ decreased the recovery of apatite and dolomite. The studied metal cations can activate quartz at a particular pH. It can be inferred from solution chemistry and zeta potential measurement that the influence of metal ions on the flotation of different minerals should be attributed to the adsorption of various hydrolysis species on the mineral surfaces. XPS analyses reveal that calcium ions can enhance the adsorption of anionic collector on apatite and quartz surfaces, and there are no apparent changes to be observed on the surface of dolomite in the absence and presence of calcium ions at a concentration of 2.5 × 10−3 M, which was in good agreement with the micro-flotation results.

Froth flotation as a promising method of coal preparation in Brazil

Energy Technology Data Exchange (ETDEWEB)

Campos, A.R. de; Almeida, S L.M. de; Santos, A.T. dos

1979-01-01

Run-of-mine coal and pre-washed coal from Santa Catarina, Brazil, were characterized using washability curves, and by particle analysis after crushing. Bench-scale froth flotation tests were then conducted with the pre-washed coal, using kerosene and diesel oil as the collectors and pine oil as the frother. The influence of starch (as depressor) on flotation was also studied. The effects of feed particle size; pH; collector, frother and depressor additions; and flotation time were investigated. A 9.5% ash content coal was obtained with a mass recovery of about 29%. (17 refs.)

The adsorption of oleate and its effect on the flotation of monazite

International Nuclear Information System (INIS)

Tran, Tam; Cheng, Tawui; Patridge, A.C.; Wong, P.L.M.

1993-01-01

The absorption of sodium oleate during the flotation of monazite has been investigated. Thermodynamic modelling was employed to study the surface chemistry of monazite. The experimental results show that the ionic distribution of the first hydroxyl rare earth species, RE(OH) 2+ , correlates well with the adsorption and flotation results. It is suggested that hydroxylation of rare earth cations at mineral surfaces could provide active sites for the chemisorption of oleate ions (sodium oleate) which enhances flotation. 13 refs., 11 figs

The Influence of Roasting Temperature on the Flotation Properties of Muscovite

Directory of Open Access Journals (Sweden)

Jiayan Tang

2016-06-01

Full Text Available Roasting and flotation are common techniques used in mineral processing, and they have increasingly been combined for the pre-concentration of muscovite from stone coal. The research was mainly to study flotation properties of muscovite after roasting at 200, 400, 600, 800 and 1000 °C, respectively. The changes of chemical and physical properties of muscovite during the roasting process were investigated by thermogravimetric analysis (TGA, Fourier transform infrared spectrum (FTIR, X-ray diffraction (XRD, X-ray photoelectron spectroscopy (XPS, Zeta potential measurements, particle size analysis, and the BET surface area measurements. The results indicated that the dehydroxylation of crystal structure took place at temperatures over 600 °C. A large number of hydroxyl groups were removed from the crystal structure of muscovite at 600–1000 °C. The layer structure, surface element distribution, and electrical properties of muscovite remained after roasting. The flotation recovery of roasted muscovite samples increased with the increase in roasting temperature in the same flotation system, because the specific surface and the adsorption capacity of dodecylamine (DDA were reduced when roasting temperature was over 600 °C. A suitable roasting temperature and dosage of reagents can be provided for the roasting-flotation of muscovite.

Adsorption of Crystal Violet on Activated Carbon Prepared from Coal Flotation Concentrate

Science.gov (United States)

Aydogmus, Ramazan; Depci, Tolga; Sarikaya, Musa; Riza Kul, Ali; Onal, Yunus

2016-10-01

The objective of this study is firstly to investigate the floatability properties of Zilan- Van coal after microwave irradiation and secondly to produce activated carbon from flotation concentrate in order to remove Crystal Violet (CV) from waste water. The flotation experiments showed that microwave heating at 0.9 kW power level for 60 sec exposure time enhanced the hydrophobicity and increased the flotation yield. The activated carbon with remarkable surface area (696 m2/g) was produced from the flotation concentrate and used to adsorb CV from aqueous solution in a batch reactor at different temperature. The adsorption properties of CV onto the activated carbon are discussed in terms of the adsorption isotherms (Langmuir and Freundlich) and found that the experimental results best fitted by the Langmuir model.

Metal biosorption-flotation. Application to cadmium removal.

Science.gov (United States)

Matis, K A; Zouboulis, A I; Grigoriadou, A A; Lazaridis, N K; Ekateriniadou, L V

1996-05-01

Biosorption using suspended non-living biomass, and flotation (for consequent solid/liquid separation of the metal-loaded biomass) have been studied in the laboratory as a possible combined process, for the removal of toxic metals (i.e., cadmium) from dilute aqueous solutions. The various parameters of the process were investigated in depth, including re-use of biosorbent. A filter aid (contained in the biomass industrial waste used) was found not really to interfere. Zeta-potential measurements of the aforementioned system were also carried out. Promising results were obtained during continuous-flow experiments. A flotation residence time of 4 min was achieved. Metal removal and suspended biomass recovery were generally over 95%.

Comparative study of the performance of conventional and column flotation when treating coking coal fines

Energy Technology Data Exchange (ETDEWEB)

Jena, M.S.; Biswal, S.K.; Das, S.P.; Reddy, P.S.R. [Institute of Minerals and Materials Technology (CSIR), Bhubaneswar - 751 013 (India)

2008-12-15

Investigations were carried out on coking coal fines by conventional cell and column flotation techniques. The effects of different operating parameters were evaluated for both conventional and column flotation. The coal fines were collected from Bhojudih washery, India. These coal fines averaged 24.4% ash, 19.8% volatile matter and 53.8% fixed carbon on a dry basis. A commercial grade sodium silicate, light diesel oil and pine oil were used as depressant, collector and frother respectively. The flotation performance was compared with release analysis. The conventional flotation results indicated that a clean coal with 14.4% ash could be obtained at 78.0% yield with 88.4% combustible recovery. The ash of the clean coal could be further reduced to 10.1% at 72.0% yield with 85.6% combustible recovery by using column flotation. The column flotation results were close to those obtained by release analysis. (author)

Heavy metal removal from waste waters by ion flotation

OpenAIRE

Polat, Hürriyet; Erdoğan, D.

2007-01-01

Flotation studies were carried out to investigate the removal of heavy metals such as copper (II), zinc (II), chromium (III) and silver (I) from waste waters. Various parameters such as pH, collector and frother concentrations and airflow rate were tested to determine the optimum flotation conditions. Sodium dodecyl sulfate and hexadecyltrimethyl ammonium bromide were used as collectors. Ethanol and methyl isobutyl carbinol (MIBC) were used as frothers. Metal removal reached about 74% under o...

(2-PYRIDYLAZO)RESORCINOL FOR FLOTATION

African Journals Online (AJOL)

KEY WORDS: Iron(II), Fe-PAR complex, Flotation, Spectrophotometry, Soils, Zinc sulfide concentrates. INTRODUCTION. 4-(2-Pyridylazo)resorcinol (PAR) is one of the most popular analytical reagents. It forms colored complexes with many metal ions and can be used for their spectrophotometric determination. A well-known ...

Estimation of metallurgical parameters of flotation process from froth visual features

Directory of Open Access Journals (Sweden)

Mohammad Massinaei

2015-06-01

Full Text Available The estimation of metallurgical parameters of flotation process from froth visual features is the ultimate goal of a machine vision based control system. In this study, a batch flotation system was operated under different process conditions and metallurgical parameters and froth image data were determined simultaneously. Algorithms have been developed for measuring textural and physical froth features from the captured images. The correlation between the froth features and metallurgical parameters was successfully modeled, using artificial neural networks. It has been shown that the performance parameters of flotation process can be accurately estimated from the extracted image features, which is of great importance for developing automatic control systems.

Black reefs: iron-induced phase shifts on coral reefs.

Science.gov (United States)

Kelly, Linda Wegley; Barott, Katie L; Dinsdale, Elizabeth; Friedlander, Alan M; Nosrat, Bahador; Obura, David; Sala, Enric; Sandin, Stuart A; Smith, Jennifer E; Vermeij, Mark J A; Williams, Gareth J; Willner, Dana; Rohwer, Forest

2012-03-01

The Line Islands are calcium carbonate coral reef platforms located in iron-poor regions of the central Pacific. Natural terrestrial run-off of iron is non-existent and aerial deposition is extremely low. However, a number of ship groundings have occurred on these atolls. The reefs surrounding the shipwreck debris are characterized by high benthic cover of turf algae, macroalgae, cyanobacterial mats and corallimorphs, as well as particulate-laden, cloudy water. These sites also have very low coral and crustose coralline algal cover and are call black reefs because of the dark-colored benthic community and reduced clarity of the overlying water column. Here we use a combination of benthic surveys, chemistry, metagenomics and microcosms to investigate if and how shipwrecks initiate and maintain black reefs. Comparative surveys show that the live coral cover was reduced from 40 to 60% to reefs on Millennium, Tabuaeran and Kingman. These three sites are relatively large (>0.75 km(2)). The phase shift occurs rapidly; the Kingman black reef formed within 3 years of the ship grounding. Iron concentrations in algae tissue from the Millennium black reef site were six times higher than in algae collected from reference sites. Metagenomic sequencing of the Millennium Atoll black reef-associated microbial community was enriched in iron-associated virulence genes and known pathogens. Microcosm experiments showed that corals were killed by black reef rubble through microbial activity. Together these results demonstrate that shipwrecks and their associated iron pose significant threats to coral reefs in iron-limited regions.

Selective flotation of PVC using gelatin and lignin alkali.

Science.gov (United States)

Yenial, Unzile; Kangal, Olgaç; Güney, Ali

2013-06-01

Recycling has become one of the most important issues as a result of increasing waste mass in present day. This is especially important for polymer wastes as they are hard to degenerate in nature. Today, most of the practical methods used for the recycling of waste mass, such as hand sorting, gravity separation, etc., cannot be performed successfully owing to close densities of polymers. Froth flotation can be used successfully and economically for this purpose. The main objective of this study was to investigate the effect of plasticizer reagents and the success of froth flotation at plastic recycling. In this study, lignin alkali and gelatin were used as plasticizer reagents. The effect of these reagents was searched with the parameters of pH, concentration, conditioning and flotation time. In the case of post-consumed polyethylene terephthalate and polyvinyl chloride (PVC), 98.9% purity of PVC was obtained at optimum conditions.

Measurement of the residence time distribution in industrial flotation equipment

International Nuclear Information System (INIS)

Yianatos, Juan; Diaz, F; Rodriguez, Jorge

2003-01-01

This work presents a determination of the effective liquid and solid residence time in mechanical cell banks of primary and sweep flotation, and in cleaning flotation columns, at Codelco-Chile's Salvador Division. The determination was carried out using the residence time distribution (RTD) measurement with radioactive tracers. Br-82 was used as the trace element for the liquid. Different kinds of minerals were used to trace the solid: a) activated global tailing (non floatable), b) tailing activated by size classifications (non floatable) and c) activated floatable mineral. The residence time measurement defined effective volumes of 50-80% of the total volume in flotation cell banks, and effective volumes of 77% of the total volume of large-size flotation solids. The effective residence time of the solid (23%+212 microns) in industrial flotation cell banks was 5% below that for the liquid. The residence time of the mineral decreased with increased particle size. Thick mineral (>150 microns) showed a residence time 8% below that for thin mineral (<45 microns). The RTD of industrial mechanical cell banks is adequately represented with a number of perfect mixers in series equivalent to the number of real bank cells. The RTD of the industrial columns equals less than two perfect mixers in series and adjusts better when considering a perfect mixers in series model, but in a different size. Common operating problems could also be observed and analyzed through the RTD measurement, such as embankment of the equipment and the deficient regulation of the outflow, used to control the pulp level (Cw)

Development of the Falea polymetallic uranium project

International Nuclear Information System (INIS)

Ring, R.; Freeman, P.

2014-01-01

The Falea uranium, silver, copper deposit is located in south western Mali, West Africa and is owned by Denison Mines Corp. The current resource estimate is approximately 45 million pounds of U_3O_8 [~17,300 t U] at an average grade of ~ 0.07% U_3O_8. [~0.06% U].The deposit also contains ~37 million Oz Ag and ~70,000 t Cu. The dominant uranium mineral is uraninite, copper is present mainly as chalcopyrite and silver mainly as argentite, and in its native form. Only 5% of the property has been explored to date, and all zones remain open. This paper reports the results of several stages of metallurgical investigations to support ongoing economic studies for the project. The polymetallic nature of the Falea deposit dictates that there are a range of flowsheet options. The ore contains both carbonate and sulphide mineralisations, which have potential impacts on acid and alkaline leaching, respectively. There is also the need to recover both silver and copper. Two primary flowsheet options were considered: 1) Acid leach of ore to recover uranium / flotation of leach residue to recover sulphide concentrate, treatment of concentrate for Cu and Ag recovery; 2) Flotation of ore / alkaline leaching of flotation tails to recover uranium and treatment of flotation concentrate for Cu and Ag recovery. A number of sub-options were considered for each flowsheet. Test work showed that high recoveries of copper and silver to flotation concentrate were obtained for both flotation of ore or acid leach residue. Uranium extraction was also > 90% for both acid and alkaline leaching. The preferred flowsheet was selected after trade-off studies by DRA. This paper presents an overview of the various flowsheet options considered, an outline of the preferred flowsheet, and the results and conclusions of on-going engineering and laboratory/pilot studies to refine the preferred flowsheet. (author)

A novel process for separation of polycarbonate, polyvinyl chloride and polymethyl methacrylate waste plastics by froth flotation.

Science.gov (United States)

Wang, Chong-Qing; Wang, Hui; Huang, Luo-Luo

2017-07-01

A novel process was proposed for separation of ternary waste plastics by froth flotation. Pretreatment of plastics with potassium permanganate (KMnO 4 ) solution was conducted to aid flotation separation of polycarbonate (PC), polyvinyl chloride (PVC) and polymethyl methacrylate (PMMA) plastics. The effect of pretreatment parameters including KMnO 4 concentration, treatment time, temperature and stirring rate on flotation recovery were investigated by single factor experiments. Surface treatment with KMnO 4 changes selectively the flotation behavior of PC, PVC and PMMA, enabling separation of the plastics by froth flotation. Mechanism of surface treatment was studied by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and X-ray photoelectron spectrum (XPS). Effect of frother concentration and flotation time on flotation behavior of plastic mixtures was further studied for flotation separation. The optimized conditions for separation of PC are KMnO 4 concentration 2mmolL -1 , treatment time 10min, temperature 60°C, stirring rate 300rpm, flotation time 1min and frother concentration 17.5mgL -1 . Under optimum conditions, PVC and PMMA mixtures are also separated efficiently by froth flotation associated with KMnO 4 treatment. The purity of PC, PVC and PMMA is up to 100%, 98.41% and 98.68%, while the recovery reaches 96.82%, 98.71% and 98.38%, respectively. Economic analysis manifests remarkable profits of the developed process. Reusing KMnO 4 solution is feasible, enabling the process greener. Copyright © 2017 Elsevier Ltd. All rights reserved.

Modelling and control of a flotation process

International Nuclear Information System (INIS)

Ding, L.; Gustafsson, T.

1999-01-01

A general description of a flotation process is given. The dynamic model of a MIMO nonlinear subprocess in flotation, i. e. the pulp levels in five compartments in series is developed and the model is verified with real data from a production plant. In order to reject constant disturbances five extra states are introduced and the model is modified. An exact linearization has been made for the non-linear model and a linear quadratic gaussian controller is proposed based on the linearized model. The simulation result shows an improved performance of the pulp level control when the set points are changed or a disturbance occur. In future the controller will be tested in production. (author)

Production of brown and black pigments by using flotation waste from copper slag.

Science.gov (United States)

Ozel, Emel; Turan, Servet; Coruh, Semra; Ergun, Osman Nuri

2006-04-01

One of the major problems in copper-producing countries is the treatment of the large amount of copper slag or copper flotation waste generated from copper slag which contains significant amounts of heavy metals such as Cu, Zn, Pb and Co. Dumping or disposal of such large quantities of flotation waste from copper slag causes environmental and space problems. In this study, the treatment of flotation waste from copper slag by a thermal method and its use as an iron source in the production of inorganic brown and black pigments that are used in the ceramic industry were investigated. The pigments were produced by calcining different amounts of flotation waste and chromite, Cr2O3, ZnO and CoO mixtures. The pigments obtained were added to transparent ceramic glazes and porcelainized tile bodies. Their colours were defined by L*a*b* measurements with a spectrophotometer. The results showed that flotation waste from copper slag could be used as an iron source to produce brown and black pigments in both ceramic body and glazes.

(AJST) EFFECT OF COLLECTOR, FROTHER AND DEPRESSANT ...

African Journals Online (AJOL)

processing involves sulphide flotation and the sulphide rougher/scavenger tails rich in oxide minerals (acid ... dose rate of 40 g/t at which the level of insolubles reduced to 35 %. ..... Crozier R.D., (1992) Flotation: theory, reagents and ore.

40 CFR 440.103 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Science.gov (United States)

2010-07-01

... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Copper, Lead... copper, lead, zinc, gold, silver, or molybdenum bearing ores or any combination of these ores from open... pollutants discharged from mills that use the froth-flotation process alone, or in conjunction with other...

Refining of fossil resin flotation concentrate from western coal. Final report

Energy Technology Data Exchange (ETDEWEB)

Jensen, G.F.; Miller, J.D.

1995-02-16

During the past several years, significant research efforts have been made to develop process technology for the selective flotation of fossil resin from western coals. As a result of these efforts, several new flotation technologies have been developed. Operation of a proof-of-concept continuous flotation circuit showed the selective flotation process to be sufficiently profitable to justify the development of a fossil resin industry. However, little attention has been given to the refining of the fossil resin flotation concentrate although solvent refining is a critical step for the fossil resin to become a marketable product. In view of this situation, DOE funded this two-year project to evaluate the following aspects of the fossil resin refining technology: 1) Characterization of the fossil resin flotation concentrate and its refined products; 2) Kinetics of fossil resin extraction; 3) Effects of operating variables on solvent extraction; 4) Extraction solvents; 5) Proof-of-concept continuous refining tests; and 6) Technical and economic analysis. The results from this research effort have led to the following conclusions: Hexane- or heptane-refined fossil resin has a light-yellow color, a melting point of 140 - 142{degrees}C, a density of 1.034 gram/cm, and good solubility in nonpolar solvents. Among the four solvents evaluated (hexane, heptane, toluene and ethyl acetate), hexane is the most appropriate solvent based on overall technical and economic considerations. Batch extraction tests and kinetic studies suggest that the main interaction between the resin and the solvent is expected to be the forces associated with solvation phenomena. Temperature has the most significant effect on extraction rate. With hexane as the solvent, a recovery of 90% cam be achieved at 50{degrees}C and 10% solids concentration with moderate agitation for 1 hour.

Treatment of wastewater containing dissolved metals by extraction-flotation

International Nuclear Information System (INIS)

Puget, Flavia Pereira

2002-02-01

In this work an alternative process for treating a wastewater containing dissolved metals (uranium and zirconium) is considered. In order to develop this work, a continuous separation unit, characterized by the association of solvent extraction and liquid-liquid flotation is used. Alamina 336 (a mixture of tri-octyl and tri-decyl amines) is used as extractant in the the extraction process, carried out inward the ejector. The splitting of the amine-water emulsion formed is carried out in a continuously operated flotation column (of approximately 2.5 L volume). The solvent extraction results showed that it is possible to reach an efficiency of about 95% for the uranium and zirconium extraction, for a metal in the feed concentration of 10 ppm and for a Q fa /Q fo ratio around 200. An efficiency of about 80% is reached in the flotation column when the liquid flowrate is equal 0.05 Lmin -1 and the air flowrate is equal 3.3 Lmin -1 . (author)

Impact of flocculation on flotation tailing's hydro-cycloning properties

Directory of Open Access Journals (Sweden)

Knežević Dinko N.

2014-01-01

Full Text Available Research results of hydro-cycloning of flocculated and non-flocculated flotation tailing from the lead and zinc open pit mine 'Suplja stijena', Sula - Montenegro have been shown in this paper. Reason for this research was finding conditions in order to separate fraction that is suitable for embankment erection. Flotation tailings has been tested in the very state that it goes out from the flotation process and tailings which is flocculated by anionic flocculant. The object was to determine the impact of flocculation on properties of hydro-cycloning products and disposal process. In hydro-cycloning process greater underflow mass is being separated with non-flocculated tailing. Values of geomechanical parameters are significantly different, especially hydro-cyclone's underflow. All geomechanical parameters of hydro-cyclone's underflow are suitable for erecting embankment which shall be made from non-flocculated tailing. Underflow drainage of non-flocculated tailing is faster while overflow drainage is slower and problematic with both tailings.

Integration process of fermentation and liquid biphasic flotation for lipase separation from Burkholderia cepacia.

Science.gov (United States)

Sankaran, Revathy; Show, Pau Loke; Lee, Sze Ying; Yap, Yee Jiun; Ling, Tau Chuan

2018-02-01

Liquid Biphasic Flotation (LBF) is an advanced recovery method that has been effectively applied for biomolecules extraction. The objective of this investigation is to incorporate the fermentation and extraction process of lipase from Burkholderia cepacia using flotation system. Initial study was conducted to compare the performance of bacteria growth and lipase production using flotation and shaker system. From the results obtained, bacteria shows quicker growth and high lipase yield via flotation system. Integration process for lipase separation was investigated and the result showed high efficiency reaching 92.29% and yield of 95.73%. Upscaling of the flotation system exhibited consistent result with the lab-scale which are 89.53% efficiency and 93.82% yield. The combination of upstream and downstream processes in a single system enables the acceleration of product formation, improves the product yield and facilitates downstream processing. This integration system demonstrated its potential for biomolecules fermentation and separation that possibly open new opportunities for industrial production. Copyright © 2017 Elsevier Ltd. All rights reserved.

Ore sorting using natural gamma radiation

International Nuclear Information System (INIS)

Clark, G.J.; Dickson, B.L.; Gray, F.E.

1980-01-01

A method of sorting an ore which emits natural gamma radiation is described, comprising the steps of: (a) mining the ore, (b) placing, substantially at the mining location, the sampled or mined ore on to a moving conveyor belt, (c) measuring the natural gamma emission, water content and mass of the ore while the ore is on the conveyor belt, (d) using the gamma, water content and mass measurements to determine the ore grade, and (e) directing the ore to a location characteristic of its grade when it leaves the conveyor belt

40 CFR 440.104 - New source performance standards (NSPS).

Science.gov (United States)

2010-07-01

... GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Copper, Lead, Zinc, Gold, Silver, and... copper, lead, zinc, gold, silver, or molybdenum bearing ores or any combination of these ores from open... discharge of process wastewater to navigable waters from mills that use the froth-flotation process alone...

Solution chemistry of carbonate minerals and its effects on the flotation of hematite with sodium oleate

Science.gov (United States)

Li, Dong; Yin, Wan-zhong; Xue, Ji-wei; Yao, Jin; Fu, Ya-feng; Liu, Qi

2017-07-01

The effects of carbonate minerals (dolomite and siderite) on the flotation of hematite using sodium oleate as a collector were investigated through flotation tests, supplemented by dissolution measurements, solution chemistry calculations, zeta-potential measurements, Fourier transform infrared (FTIR) spectroscopic studies, and X-ray photoelectron spectroscopy (XPS) analyses. The results of flotation tests show that the presence of siderite or dolomite reduced the recovery of hematite and that the inhibiting effects of dolomite were stronger. Dissolution measurements, solution chemistry calculations, and flotation tests confirmed that both the cations (Ca2+ and Mg2+) and CO3 2- ions dissolved from dolomite depressed hematite flotation, whereas only the CO3 2- ions dissolved from siderite were responsible for hematite depression. The zeta-potential, FTIR spectroscopic, and XPS analyses indicated that Ca2+, Mg2+, and CO3 2- (HCO3 -) could adsorb onto the hematite surface, thereby hindering the adsorption of sodium oleate, which was the main reason for the inhibiting effects of carbonate minerals on hematite flotation.

Production of titanium silicate compositions from technogenic titanium containing waste of Khibiny ores' enrichment

Directory of Open Access Journals (Sweden)

Shchukina E. S.

2017-03-01

Full Text Available The low level of complexity in the processing of raw materials at mining and processing enterprises adversely affect the environment causing considerable damage to it. Meanwhile technological waste is a cheap source of raw materials for liquid products of functional purpose, particularly inorganic filler which are widely used in the manufacture of paints and building materials, paper, plastics, insulating and protective materials. Improved performance and physical and chemical properties of materials are achieved by optimizing the composition and dispersion of the particles. By the example of the research subjects received from the flotation waste nepheline ore-dressing, it has been shown that a high degree of homogenization to obtain fine mixtures (75 % of 3–4 micron fraction composite filler powders the ultrafine grinding method achieved by using a planetary ball mill for a short period of time (at least 1 hours. The use of other grinding methods, for example by means of ball mill or a vibration such effect is not obtained. At the conditions of ultrafine grinding the ionization and amorphization of the surface layer of powder material particles (mechanical activated processing are occurred. This increases its activity by reacting with organic and inorganic binding, and provides high performance. The obtained filler has been tested in the composition of temperature-controlled sealants and glues used in the aerospace industry, shipbuilding and electronics. To obtain such materials sphene and nepheline received from industrial tailings of Khibiny apatite-nepheline ore deposits are used

Fine particles flotation of the Moatize coal/Mozambique

Science.gov (United States)

Castro, Amilton; de Brum, Irineu A. S.

2017-11-01

This study was done from a sample of coal mined at the Vale-Mozambique mine, located in Moatize district, Tete Province. The aim of this work is to analyze the reagent system in the flotation of coal fines belonging to the UCB layer. Among coal processing methods, flotation stands out as one of the most important for the concentration of this material, in particular in the treatment of fine particles. The total feed of the Vale-Mozambique processing plant is 8000 tph of coal, where 10% of this feed corresponds to the fine fraction that feeds the flotation circuit. The material used in this study had a particle size of 96% smaller than 0.25 mm. The reagents used in the flotation tests were Betacol and diesel oil as hydrophobizing agents and MIBC as frother. The range of Betacol concentrations in the first test phase was 200 g / t at 500 g / t, and in the second phase 200 g / t at 500 g / t of diesel oil and MIBC were kept constant at 300 g / t. The immediate analysis followed the Brazilian standards: NBR 8289, NBR 8293, NBR 8290, NBR 8299. The results showed that it is possible, from a feed with the ash content around 22.84%, to obtain products with levels below of 10% ash, with a mass recovery around 50%. The recovery of carbonaceous matter was also evaluated and presented positive results. Complementing this study, the effect of H2O recovery was evaluated and it was observed that for the concentrations of Betacol the recoveries ranged from 6 to 9%, and for diesel oil plus MIBC were 4 to 7%.

Studies on uranium ore processing

International Nuclear Information System (INIS)

Kim, C.H.; Park, S.W.; Lim, J.K.; Chung, M.K.

1981-01-01

Chemical and chemical engineering techniques of the uranium ore processing established by France COGEMA (Compagnie Generale des Matieres Nucleaires) have been comprehensively reviewed in preparation for successful test operation of the pilot plant to be completed by the end of 1981. It was found that the amount of sulfuric acid (75 Kg/t, ore) and sodium chlorate (2.5 Kg/t, ore) recommended by COGEMA should be increased up to 100 Kg/t, ore and 10 Kg/t, ore respectively to obtain satisfactory leach of uranium for some ore samples produced at the different pits of Goesan uranium mine. Conditions of the other processes such as solvent extraction, stripping, and precipitation of yellow cake were generally agreed with the results of intensive studies done by this laboratory

Mathematical simulation of column flotation in pilot scale

International Nuclear Information System (INIS)

Simpson, J.; Jordan, D.; Cifuentes, G.; Morales, A.; Briones, L.

2010-01-01

The Procemin-I area of the Centro Minero Metalurgico Tecnologia y Servicio (CIMM T and S), has a full milling and flotation pilot plant in which several experiences are developed as: optimization of circuits, plant design, procurement of operating parameters, etc. Ones of the equipment in operation is the column flotation to pilot scale, witch have a medium level of automation. The problem presented in the operation of the column flotation is the low relationship during the operation between the operating basis parameters and the metallurgical results. The mathematical models used today to estimate the metallurgical results (i.e.: concentrate, tailing, enrichment and recovery) depending on variables that are manipulated by hand according the operator experience. But the process engineer needs tools without subjective vision to obtain the best performance of the column. The method used to help the column operation was a mathematical model based on the Stepwise Regression then considering empirical relationships between operational variables and experimental results. All the mathematical relationship developed in this study have a good correlation (up 90 % of precision), except one (up 70 %) due by non regular mineralogical feed. (Author) 7 refs.

Heavy metal and nutrient uptake in plants colonizing post-flotation copper tailings.

Science.gov (United States)

Kasowska, Dorota; Gediga, Krzysztof; Spiak, Zofia

2018-01-01

Copper ore mining and processing release hazardous post-flotation wastes that are difficult for remediation. The studied tailings were extremely rich in Cu (1800 mg kg -1 ) and contaminated with Co and Mn, and contained very little available forms of P, Fe, and Zn. The plants growing in tailings were distinctly enriched in Cu, Cd, Co, Ni, and Pb, and the concentration of copper achived the critical toxicity level in shoots of Cerastium arvense and Polygonum aviculare. The redundancy analysis demonstrated significant relationship between the concentration of available forms of studied elements in substrate and the chemical composition of plant shoots. Results of the principal component analysis enabled to distinguish groups of plants which significantly differed in the pattern of element accumulation. The grass species Agrostis stolonifera and Calamagrostis epigejos growing in the tailings accumulated significantly lower amounts of Cu, but they also had the lowest levels of P, Fe, and Zn in comparison to dicotyledonous. A. stolonifera occurred to be the most suitable species for phytostabilization of the tailings with regard to its low shoot Cu content and more efficient acquisition of limiting nutrients in relation to C. epigejos. The amendments improving texture, phosphorus fertilization, and the introduction of native leguminous species were recommended for application in the phytoremediation process of the tailings.

THE DEPRESSION OF PYRITE FLOTATION BY THIOBACILLUS FERROOXIDANS

Institute of Scientific and Technical Information of China (English)

无

2000-01-01

The experimental studies on the microbial flotation of a pure pyrite sample using Thiobacillus ferrooxidans was conducted in the laboratory. The results indicate that Thiobacillus ferrooaidans has strong depression effect on the flotation of pyrite. Thiobacillus f errooxidans can adsorb on the surface of pyrite in a very short time (a few min. ), changing the surface from hydrophobic into hydrophilic and making the pyrite particles to lose their floatability. Therefore, Thiobacillus ferrooxidans is an effective microbial depressant of pyrite. It has also been pointed out that the depression of pyrite by Thiobacillus ferrooxidans is caused by the adsorption of the microbial colloids, but not by the oxidation effect.

New interpretation of the dominant ore-controlling factor of the uranium ore field No. 322

International Nuclear Information System (INIS)

Liu Xiang; Yang Chongqiu

1996-01-01

The NE-trending fault structures in ore field NO. 322 are characterized by compress-shearing, left-Lateral left-slipping, having an obvious control over the Localisation of the ore field No. 322, and are the dominant ore-controlling factor of the ore field NO.322. Resulting from the sinistral displacement of the NE-trending fault, there is a pull-apart basin in the Feng Zhou area. The formation and evolution of the NE-trending fault zone and the Feng Zhou basin control the formation of uranium deposits of ore field No. 322

New Insights into the Role of Pb-BHA Complexes in the Flotation of Tungsten Minerals

Science.gov (United States)

Yue, Tong; Han, Haisheng; Hu, Yuehua; Sun, Wei; Li, Xiaodong; Liu, Runqing; Gao, Zhiyong; Wang, Li; Chen, Pan; Zhang, Chenyang; Tian, Mengjie

2017-11-01

Lead ions (lead nitrate) were introduced to modify the surface properties of tungsten minerals, effectively improving the floatability, with benzohydroxamic acid (BHA) serving as the collector. Flotation tests indicated that Pb-BHA complexes were the active species responsible for flotation of the tungsten minerals. The developed Pb-BHA complexes and the novel flotation process effectively increased the recovery of scheelite and wolframite, simplified the technological process, and led to reduced costs. Fourier transform infrared spectra data showed the presence of adsorbed Pb-BHA complexes on the surface of the minerals. The characteristic peaks of BHA shifted by a considerable extent, indicating that chemical adsorption plays an important role in the flotation process. Zeta potential results confirmed physical adsorption of the positively charged Pb-BHA complexes on the mineral surfaces. The synergistic effect between chemical and physical adsorption facilitated the maximum flotation recovery of scheelite and wolframite.

Radiometric on-line-determination of lead in lead-zinc ore processing

International Nuclear Information System (INIS)

Lubecki, A.; Wiese, K.; Gralher, M.

1983-01-01

By the example of Pb determination in PbS-ZnS flotation liquids the advancement of the radionuclide (Co-57) excited X-ray fluorescence assay technique Graf is reported. The technique of measurement, previously tested in analyzing baryte contained in the fluorsphar flotation liquid was adapted to the conditions prevailing in the PbS-ZnS flotation liquid by modification of theory, principle of measurement, and measuring technique. Testing on an industrial scale was performed in the flotation facility of Preussag AG Metall at Bad Grund, more particularly in the process streams of strategic importance such as ''total tailings'', ''Pb tailings'', and ''lotation feed''. Correspondence between the on-line analytical values and the comparable values from conventional operating analysis was fair. For 31 reference samples from ''total tailings'' and for 20 reference samples from ''Pb tailings'' the mean scattering was calculated to be approx. 0,04%, for 20 reference samples from ''flotation feed'' it amounted to 0,14% Pb. (orig./HP) [de

Cross flow cyclonic flotation column for coal and minerals beneficiation

Science.gov (United States)

Lai, Ralph W.; Patton, Robert A.

2000-01-01

An apparatus and process for the separation of coal from pyritic impurities using a modified froth flotation system. The froth flotation column incorporates a helical track about the inner wall of the column in a region intermediate between the top and base of the column. A standard impeller located about the central axis of the column is used to generate a centrifugal force thereby increasing the separation efficiency of coal from the pyritic particles and hydrophillic tailings.

Flotation atomic absorption determination of bismuth in nonferrous metal alloys

International Nuclear Information System (INIS)

Ososkov, V.K.; Plintus, A.M.; Kornelli, M.Eh.; Zakhariya, A.N.; Lozanova, E.V.

1986-01-01

Technique of flotation concentration and atomic absorption determination of bismuth microquantities in alloys on the basis of copper and zinc has been developed. Fine-dispersed EhDEh-10P anionite was used as a carrier in flotation concentration. State standard samples (SSS) of brasses and German silver were used as analysed objects. Effect of macrocomponents on the results of bismuth content determination has been studied. Satisfactory coincidence of the results obtained and SSS certificates is shown

Separation of polyethylene terephthalate from municipal waste plastics by froth flotation for recycling industry

International Nuclear Information System (INIS)

Wang, Chong-Qing; Wang, Hui; Liu, You-Nian

2015-01-01

Highlights: • Factors of NaOH treatment were studied by orthogonal and single factor experiments. • Mechanism of alkaline treatment for facilitating flotation was manifested. • Flotation separation of PET was achieved with high purity and efficiency. • A flow sheet of purification PET from MWP was designed. - Abstract: Recycling is an effective way to manage plastic wastes and receives considerable attention. Since plastic mixtures are difficult to recycle because of their intrinsic characteristics, separation of mixed plastics is the key problem for recycling. Separation of polyethylene terephthalate (PET) from municipal waste plastics (MWP) by froth flotation combined with alkaline pretreatment was investigated for recycling industry. The effect of process variables was estimated by L 9 (3 4 ) orthogonal array of experiments and single factor experiments. The optimum conditions of alkaline pretreatment are 10 wt% sodium hydroxide, 20 min and 70 °C. After alkaline pretreatment under optimum conditions, flotation separation PET from acrylonitrile–butadiene–styrene, polystyrene, polycarbonate or polyvinyl chloride was achieved with high purity and efficiency. The purity of PET is up to 98.46% and the recovery is above 92.47%. A flow sheet of separation PET from MWP by a combination of froth flotation and sink float separation was designed. This study facilitates industrial application of plastics flotation and provides technical insights into recycling of waste plastics

Separation of polyethylene terephthalate from municipal waste plastics by froth flotation for recycling industry

Energy Technology Data Exchange (ETDEWEB)

Wang, Chong-Qing; Wang, Hui, E-mail: huiwang1968@163.com; Liu, You-Nian

2015-01-15

Highlights: • Factors of NaOH treatment were studied by orthogonal and single factor experiments. • Mechanism of alkaline treatment for facilitating flotation was manifested. • Flotation separation of PET was achieved with high purity and efficiency. • A flow sheet of purification PET from MWP was designed. - Abstract: Recycling is an effective way to manage plastic wastes and receives considerable attention. Since plastic mixtures are difficult to recycle because of their intrinsic characteristics, separation of mixed plastics is the key problem for recycling. Separation of polyethylene terephthalate (PET) from municipal waste plastics (MWP) by froth flotation combined with alkaline pretreatment was investigated for recycling industry. The effect of process variables was estimated by L{sub 9} (3{sup 4}) orthogonal array of experiments and single factor experiments. The optimum conditions of alkaline pretreatment are 10 wt% sodium hydroxide, 20 min and 70 °C. After alkaline pretreatment under optimum conditions, flotation separation PET from acrylonitrile–butadiene–styrene, polystyrene, polycarbonate or polyvinyl chloride was achieved with high purity and efficiency. The purity of PET is up to 98.46% and the recovery is above 92.47%. A flow sheet of separation PET from MWP by a combination of froth flotation and sink float separation was designed. This study facilitates industrial application of plastics flotation and provides technical insights into recycling of waste plastics.

Heterocoagulation of chalcopyrite and pyrite minerals in flotation separation.

Science.gov (United States)

Mitchell, Timothy K; Nguyen, Anh V; Evans, Geoffrey M

2005-06-30

Heterocoagulation between various fine mineral particles contained within a mineral suspension with different structural and surface chemistry can interfere with the ability of the flotation processes to selectively separate the minerals involved. This paper examines the interactions between chalcopyrite (a copper mineral) and pyrite (an iron mineral often bearing gold) as they approach each other in suspensions with added chemicals, and relates the results to the experimental data for the flotation recovery and selectivity. The heterocoagulation was experimentally studied using the electrophoretic light scattering (ELS) technique and was modelled by incorporating colloidal forces, including the van der Waals, electrostatic double layer and hydrophobic forces. The ELS results indicated that pyrite has a positive zeta potential (zeta) up to its isoelectric point (IEP) at approximately pH 2.2, while chalcopyrite has a positive zeta up to its IEP at approximately pH 5.5. This produces heterocoagulation of chalcopyrite with pyrite between pH 2.2 and pH 5.5. The heterocoagulation was confirmed by the ELS spectra measured with a ZetaPlus instrument from Brookhaven and by small-scale flotation experiments.

Flotation of phosphorous-uraniferous minerals from Itataia

International Nuclear Information System (INIS)

Aquino, J.A. de.

1984-01-01

Experimental conditions were established, in laboratory and pilot scales, for the flotation of a sample of a phosphorus-uraniferous mineral from Itataia mines (CE, Brazil), basically composed of apatite and calcite. Laboratory investigations led to the optimization of the most important flotation variables and of the reagents system (tall-oil, collamil and sodium silicate) in the roughing, scavenging and cleaning steps of the process. In pilot scale, flowsheet tests were performed under the same conditions proposed for laboratory studies. The optimization of laboratory conditions led to the following yields: 29.3% of P 2 O 5 concentrates and 73.5% P 2 O 5 recovery. In the pilot scale tests, 28.4% of P 2 O 5 concentrates and 76.7% P 2 O 5 recovery yields were obtained. (Author) [pt

Statistical Evaluation and Optimization of Factors Affecting the Leaching Performance of Copper Flotation Waste

OpenAIRE

Çoruh, Semra; Elevli, Sermin; Geyikçi, Feza

2012-01-01

Copper flotation waste is an industrial by-product material produced from the process of manufacturing copper. The main concern with respect to landfilling of copper flotation waste is the release of elements (e.g., salts and heavy metals) when in contact with water, that is, leaching. Copper flotation waste generally contains a significant amount of Cu together with trace elements of other toxic metals, such as Zn, Co, and Pb. The release of heavy metals into the environment has resulted in ...

Using flotation in ethanol to separate filled and empty seeds of Pinus ...

African Journals Online (AJOL)

In this study, the separation of filled and empty seeds of Crimean pine [Pinus nigra Arn. ssp. pallasiana (Lamb.) Holmboe] by flotation in ethanol and the effect of this treatment on seed germination were investigated. Flotation tests in 96% ethanol by the density method and then germination tests were made on the seeds ...

Using flotation in ethanol to separate filled and empty seeds of Pinus ...

African Journals Online (AJOL)

USER

2010-06-21

Jun 21, 2010 ... and empty seeds by the flotation method. It is quite important not to damage the seed embryo and con- sequently seed germination ability during or after the flotation treatment by these liquids that have different densities. On the other hand, when Crimean pine seeds are left in water, the seeds generally ...

Coal flotation - bench-scale study. Flotacao de carvao estudo em escala de bancada

Energy Technology Data Exchange (ETDEWEB)

Campos, A.R. de; Almeida, S L.M. de; Santos, A.T. dos

1979-01-01

Run-of-mine coal and pre-washed coal from Santa Catarina, Brazil, were characterized using washability curves and by particle size analysis after crushing. Bench-scale froth flotation tests were then conducted with the pre-washed coal. Kerosene and diesel oil were used as the collectors, and pine oil as the frother. The influence of starch (as depressor) on flotation was also studied. The effects of feed particle size, pH, collector addition, frother addition, depressor addition and flotation time were investigated. A 9.5% ash content coal could be obtained with a mass recovery of about 29%. (17 refs.)

Flotation and screening recovery of titanium minerals from a monazite mineral sands circuit

International Nuclear Information System (INIS)

Bruckard, W.J.; Heyes, G.W.; Guy, P.J.

2001-01-01

Investigations were undertaken to assess the suitability of CSIRO flotation methods for improving the efficiency of separation of heavy minerals in the monazite circuit at the Westralian Sands Limited operations at Capel, Western Australia. Flotation work was conducted on two plant samples. The first was a high-titanium product containing considerable amounts of zircon and silica as quartz and aluminosilicates, and the second was a low monazite/zircon material containing high levels of silica. A three-stage process including reverse flotation was developed to treat the first sample. In this process monazite, zircon, quartz, and aluminosilicates were selectively concentrated by flotation and screening to produce a titanium-rich product. In the first stage, an acid amine float, monazite, zircon, and some non-zircon silica were recovered and in the second stage, an alkaline amine float using a fluoride activator, more quartz and staurolite were floated. The titanium minerals were thus concentrated in the unfloated fraction. In the third stage, the titanium-rich flotation tail was screened at 250 μm to remove the remaining coarse aluminosilicates. In a single pass, the three-stage process yielded a TiO 2 recovery of 64.0 per cent with the titanium-rich product assaying 70.3 per cent TiO 2

Separation of oily materials in radioactive waste waters by flotation. Flotation kinetics; Separacion de materiales oleosos en aguas residuales radiactivas por flotacion. Cinetica de flotacion

Energy Technology Data Exchange (ETDEWEB)

Flores E, R M; Ortiz O, H B [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

2003-07-01

The rate of separation of oil and total cobalt in the oleaginous residual water previously treated by coagulation/flocculation with a quaternary ammonium amine (25 mgL{sup -1}) and with modified anionic polyacrylamide (1.5 mgL{sup -1}) (pH = 7, G{sub 1} = 300 s{sup -1} and G{sub 2} = 30 s{sup -1}) was determined. The experimental essays to determine the flotation kinetics, its were carried out using as operation and control parameters the air/solids relationship (G/S 0.35), pressure (P =620 kPa) and volume of air-water mixture (V = 37% of V{sub f}), obtained in previous essays, at two different pressure levels and volume of discharged mixture. The kinetic studies of flotation obtained for the flotation system with conventional air dissolved (DAF) its suggest a first order kinetics that it can be represented by the SCC model. At the same time its show that the separation of the present pollutants in the residual water is governed by the removal velocity of the oil. Meanwhile, the concentration of total Co below 1 mgL{sup -1}, on the other hand, the concentration of the {sup 60} Co at the end of the flotation process resulted smaller than 0.008 Bq/ml, as long as the one {sup 54} Mn were not detectable. (Author)

Inhalation of uranium ores

International Nuclear Information System (INIS)

Stuart, B.O.; Jackson, P.O.

1975-01-01

In previous studies the biological dispositions of individual long-lived alpha members of the uranium chain ( 238 U, 234 U and 230 Th) were determined during and following repeated inhalation exposures of rats to pitchblende (26 percent U 3 O 8 ) ore. Although finely dispersed ore in secular equilibrium was inhaled, 230 Th/ 234 U radioactivity ratios in the lungs rose from 1.0 to 2.5 during 8 weeks of exposures and increased to 9.2 by four months after cessation of exposures. Marked non-equilibrium levels were also found in the tracheobronchial lymph nodes, kidneys, liver, and femur. Daily exposures of beagle dogs to high levels of this ore for 8 days resulted in lung 230 Th/ 234 U ratios of >2.0. Daily exposures of dogs to lower levels (0.1 mg/1) for 6 months, with sacrifice 15 months later, resulted in lung and thoracic lymph node 230 Th/ 234 U ratios ranging from 3.6 to 9 and nearly 7, respectively. The lungs of hamsters exposed to carnotite (4 percent U 3 O 8 ) ore in current lifespan studies show 230 Th/ 234 U ratios as high as 2.0 during daily inhalation of this ore in secular equilibrium. Beagle dogs sacrificed after several years of daily inhalations of the same carnotite ore plus radon daughters also showed marked non-equilibrium ratios of 230 Th/ 234 U, ranging from 5.6 to 7.4 in lungs and 6.2 to 9.1 in thoracic lymph nodes. This pattern of higher retention of 230 Th than 234 U in lungs, thoracic lymph nodes, and other tissues is thus consistent for two types of uranium ore among several species and suggests a reevaluation of maximum permissible air concentrations of ore, currently based only on uranium content

Flotation separation of polyvinyl chloride and polyethylene terephthalate plastics combined with surface modification for recycling.

Science.gov (United States)

Wang, Chongqing; Wang, Hui; Fu, Jiangang; Zhang, Lingling; Luo, Chengcheng; Liu, Younian

2015-11-01

Surface modification with potassium permanganate (KMnO4) solution was developed for separation of polyvinyl chloride (PVC) and polyethylene terephthalate (PET) waste plastics. The floatability of PVC decreases with increasing of KMnO4 concentration, treatment time, temperature and stirring rate, while that of PET is unaffected. Fourier transform infrared (FT-IR) analysis confirms that mechanism of surface modification may be due to oxidization reactions occurred on PVC surface. The optimum conditions are KMnO4 concentration 1.25 mM/L, treatment time 50 min, temperature 60°C, stirring rate 300 r/min, frother concentration 17.5 g/L and flotation time 1 min. PVC and PET with different particle sizes were separated efficiently through two-stage flotation. Additionally, after ultrasonic assisted surface modification, separation of PVC and PET with different mass ratios was obtained efficiently through one-stage flotation. The purity and the recovery of the obtained products after flotation separation are up to 99.30% and 99.73%, respectively. A flotation process was designed for flotation separation of PVC and PET plastics combined with surface modification. This study provides technical insights into physical separation of plastic wastes for recycling industry. Copyright © 2015 Elsevier Ltd. All rights reserved.

Enhanced sulfidation xanthate flotation of malachite using ammonium ions as activator

OpenAIRE

Dandan Wu; Wenhui Ma; Yingbo Mao; Jiushuai Deng; Shuming Wen

2017-01-01

In this study, ammonium ion was used to enhance the sulfidation flotation of malachite. The effect of ammonium ion on the sulfidation flotation of malachite was investigated using microflotation test, inductively coupled plasma (ICP) analysis, zeta potential measurements, and scanning electron microscope analysis (SEM). The results of microflotation test show that the addition of sodium sulfide and ammonium sulfate resulted in better sulfidation than the addition of sodium sulfide alone. The ...

Relative flotation response of zinc sulfide: Mineral and precipitate

Energy Technology Data Exchange (ETDEWEB)

Rao, S.R.; Finch, J.A. [McGill Univ., Montreal, Quebec (Canada). Dept. of Mining and Metallurgical Engineering; Zhou, Z.; Xu, Z. [Univ. of Alberta, Edmonton, Alberta (Canada). Dept. of Chemical and Materials Engineering

1998-04-01

Flotation continues to extend to nonmineral applications, including recycling of materials, soil remediation, and effluent treatment. A study has been conducted to compare the floatability of fine zinc sulfide (ZnS) precipitates and sphalerite particles. The floatability of the precipitates was significantly poorer compared to sphalerite particles when xanthate was used as the collector. The floatability was improved by using dodecylamine as the collector, and the difference in floatability between the precipitates was further improved significantly by incorporating a hydrodynamic cavitation tube in a conventional (mechanical) flotation cell. The improved kinetics was attributed to in-situ gas nucleation on the precipitates.

Project O.R.B (Operation Reef Ball): Creating Artificial Reefs, Educating the Community

Science.gov (United States)

Phipps, A.

2012-04-01

The Project O.R.B. (Operation Reef Ball) team at South Plantation High School's Everglades Restoration & Environmental Science Magnet Program is trying to help our ailing south Florida coral reefs by constructing, deploying, and monitoring designed artificial reefs. Students partnered with the Reef Ball Foundation, local concrete companies, state parks, Girl Scouts, Sea Scouts, local universities and environmental agencies to construct concrete reef balls, each weighing approximately 500 lbs (227 kg). Students then deployed two artificial reefs consisting of over 30 concrete reef balls in two sites previously permitted for artificial reef deployment. One artificial reef was placed approximately 1.5 miles (2.4 km) offshore of Golden Beach in Miami-Dade County with the assistance of Florida Atlantic University and their research vessel. A twin reef was deployed at the mouth of the river in Oleta River State Park in Miami. Monitoring and maintenance of the sites is ongoing with semi-annual reports due to the Reef Ball Foundation and DERM (Department of Environmental Resource Management) of Miami-Dade County. A second goal of Project O.R.B. is aligned with the Florida Local Action Strategy, the Southeast Florida Coral Reef Initiative, and the U.S. Coral Reef Task Force, all of which point out the importance of awareness and education as key components to the health of our coral reefs. Project O.R.B. team members developed and published an activity book targeting elementary school students. Outreach events incorporate cascade learning where high school students teach elementary and middle school students about various aspects of coral reefs through interactive "edu-tainment" modules. Attendees learn about water sampling, salinity, beach erosion, surface runoff, water cycle, ocean zones, anatomy of coral, human impact on corals, and characteristics of a well-designed artificial reef. Middle school students snorkel on the artificial reef to witness first-hand the success

Ore sorting

International Nuclear Information System (INIS)

Hawkins, A.P.; Richards, A.W.

1982-01-01

In an ore sorting apparatus, ore particles are bombarded with neutrons in a chamber and sorted by detecting radiation emitted by isotopes of elements, such as gold, forming or contained in the particles, using detectors and selectively controlling fluid jets. The isotopes can be selectively recognised by their radiation characteristics. In an alternative embodiment, shorter life isotopes are formed by neutron bombardment and detection of radiation takes place immediately adjacent the region of bombardment

Removal of Cobalt ion by Foam Flotation(I)

Energy Technology Data Exchange (ETDEWEB)

Jung, I.H.; Park, H.S.; Moon, J.S.; Yim, S.P.; Bae, K.K. [Korea Atomic Energy Research Institute (Korea)

1999-02-01

Simulated liquid waste containing 50 ppm cobalt ion was treated by precipitate flotation using the surfactant of sodium lauryl sulfate. The effects of initial cobalt ion concentration, pH, surfactant concentration, removal time, gas flow rate and foreign ions were estimated on removal efficiency. 35% H{sub 2}O{sub 2} was added for pre-treatment stage before precipitate flotation. As the result of pre-treatment, optimum removal pH and the pH of treated water being discharged were lowed and optimum removal pH range was broadened. For the result of this experiment, 99.8% removal efficiency was obtained at the condition of 50ppm of initial cobalt ion concentration, pH 9.5, 70 mL/min of gas flow rate, and 30 min of removal time. Attraction between precipitate and surfactant was supposed to be influenced by solubility and chemical affinity among species in solution as well as zeta potential. The influence of foreign ions such as, NO{sub 3}{sup -}, SO{sub 4}{sup -2}, Na{sup +}, Ca{sup +2} on the removal efficiency was also observed. Removal efficiency by precipitate flotation containing o.1 M of SO4{sup -}2 ion decreased to 90% due to the decrease of zeta potential and interruption of precipitation. 12 refs., 8 figs.

The Effects of Calcium Ions on the Flotation of Sillimanite Using Dodecylammonium Chloride

Directory of Open Access Journals (Sweden)

Zhijie Chen

2017-02-01

Full Text Available The effects of Ca2+ ions on the flotation of sillimanite using dodecylammonium chloride as a collector were investigated by micro-flotation tests, zeta potential measurements, solution chemistry analysis and molecular dynamics (MD simulation. The micro-flotation results indicated that Ca2+ ions remarkably inhibit the flotation of sillimanite in the pH range of 2.0–9.0. The point of zero charge (PZC of sillimanite changed from 5.4 to 6.1 with the addition of Ca2+ ions. Meanwhile, the calculated concentration of RNH3+ in the sillimanite interface layer decreased in the presence of Ca2+ ions. The results of MD simulation revealed that Ca2+ ions have strong binding energy with the sillimanite (010 surface, and the binding energy of RNH3+ with sillimanite (010 surface reduced in the presence of Ca2+ ions. The conclusions drawn from the computations are in good agreement with the experimental results.

Anisotropic surface physicochemical properties of spodumene and albite crystals: Implications for flotation separation

Science.gov (United States)

Xu, Longhua; Peng, Tiefeng; Tian, Jia; Lu, Zhongyuan; Hu, Yuehua; Sun, Wei

2017-12-01

Aluminosilicate minerals (e.g., spodumene, albite) have complex crystal structures and similar surface chemistries, but they have poor selectivity compared to traditional fatty acid collectors, making flotation separation difficult. Previous research has mainly considered the mineral crystal structure as a whole. In contrast, the surface characteristics at the atomic level and the effects of different crystal interfaces on the flotation behavior have rarely been investigated. This study focuses on investigating the surface anisotropy quantitatively, including the chemical bond characteristics, surface energies, and broken bond densities, using density functional theory and classical theoretical calculations. In addition, the anisotropy of the surface wettability and adsorption characteristics were examined using contact angle, zeta potential, and Fourier-transform infrared measurements. Finally, these surface anisotropies with different flotation behaviors were investigated and interpreted using molecular dynamics simulations, scanning electron microscopy, and X-ray photoelectron spectroscopy. This systematic research offers new ideas concerning the selective grinding and stage flotation of aluminosilicate minerals based on the crystal characteristics.

Geomorphology and sediment transport on a submerged back-reef sand apron: One Tree Reef, Great Barrier Reef

Science.gov (United States)

Harris, Daniel L.; Vila-Concejo, Ana; Webster, Jody M.

2014-10-01

Back-reef sand aprons are conspicuous and dynamic sedimentary features in coral reef systems. The development of these features influences the evolution and defines the maturity of coral reefs. However, the hydrodynamic processes that drive changes on sand aprons are poorly understood with only a few studies directly assessing sediment entrainment and transport. Current and wave conditions on a back-reef sand apron were measured during this study and a digital elevation model was developed through topographic and bathymetric surveying of the sand apron, reef flats and lagoon. The current and wave processes that may entrain and transport sediment were assessed using second order small amplitude (Stokes) wave theory and Shields equations. The morphodynamic interactions between current flow and geomorphology were also examined. The results showed that sediment transport occurs under modal hydrodynamic conditions with waves the main force entraining sediment rather than average currents. A morphodynamic relationship between current flow and geomorphology was also observed with current flow primarily towards the lagoon in shallow areas of the sand apron and deeper channel-like areas directing current off the sand apron towards the lagoon or the reef crest. These results show that the short-term mutual interaction of hydrodynamics and geomorphology in coral reefs can result in morphodynamic equilibrium.

Accretion history of mid-Holocene coral reefs from the southeast Florida continental reef tract, USA

Science.gov (United States)

Stathakopoulos, A.; Riegl, B. M.

2015-03-01

Sixteen new coral reef cores were collected to better understand the accretion history and composition of submerged relict reefs offshore of continental southeast (SE) Florida. Coral radiometric ages from three sites on the shallow inner reef indicate accretion initiated by 8,050 Cal BP and terminated by 5,640 Cal BP. The reef accreted up to 3.75 m of vertical framework with accretion rates that averaged 2.53 m kyr-1. The reef was composed of a nearly even mixture of Acropora palmata and massive corals. In many cases, cores show an upward transition from massives to A. palmata and may indicate local dominance by this species prior to reef demise. Quantitative macroscopic analyses of reef clasts for various taphonomic and diagenetic features did not correlate well with depth/environmental-related trends established in other studies. The mixed coral framestone reef lacks a classical Caribbean reef zonation and is best described as an immature reef and/or a series of fused patch reefs; a pattern that is evident in both cores and reef morphology. This is in stark contrast to the older and deeper outer reef of the SE Florida continental reef tract. Accretion of the outer reef lasted from 10,695-8,000 Cal BP and resulted in a larger and better developed structure that achieved a distinct reef zonation. The discrepancies in overall reef morphology and size as well as the causes of reef terminations remain elusive without further study, yet they likely point to different climatic/environmental conditions during their respective accretion histories.

The Effect of Quartz on the Flotation of Fine Wolframite with Octyl Hydroxamic Acid

Directory of Open Access Journals (Sweden)

Qingyou Meng

2017-09-01

Full Text Available The influence of quartz on the flotation of fine wolframite using octyl hydroxamic acid (OHA as the collector was investigated by micro-flotation tests, inductively coupled plasma (ICP measurements, adsorption experiments, zeta potential, and Fourier transform infrared spectroscopy (FT-IR analysis. Micro-flotation tests showed that a large difference in floatability existed between fine wolframite and quartz in the pH range of 7.0 to 10.0. However, in a synthetic mixture, the flotation separation of fine wolframite from quartz became more difficult as the particle size of the latter decreased. When a dissolved solution of wolframite was used as the flotation medium, quartz floatability improved significantly. Zeta potentials of quartz particles shifted positively in the dissolved solution of wolframite compared to distilled water, especially at a pH level of 7.0–10.0, which was attributed to the metal ions dissolved from the wolframite being adsorbed onto the quartz surface. The surface activation of quartz led to an increase in the OHA adsorption and made the surface hydrophobic. FT-IR analysis further demonstrated that OHA could adsorb onto the activated quartz surface through a dominantly chemical process.

Ion flotation of rhodium(III) and palladium(II) with anionic surfactants.

Science.gov (United States)

He, X C

1991-03-01

The ion flotation of rhodium(III) and palladium(II) with some anionic surfactants has been investigated. Two flotation procedures are proposed for the separation of some platinum metals, based on differences in the kinetic properties of the chloro-complexes of rhodium(III), palladium(II) and platinum(IV). The first involves the selective flotation of Rh(H(2)O)(3+)(6) from PdCl(2-)(4) and PtCl(2-)(6) in dilute hydrochloric acid with sodium dodecylbenzenesulfonate (SDBS). After precipitation of the hydroxide and redissolution in dilute acid, the Rh(III) is converted into Rh(H(2)O)(3+)(6), Pd(II) and Pt(IV) remaining as PdCl(2-)(4) and PtCl(2-)(6) respectively, and separation is achieved by floating the Rh(H(2)O)(3+)(6) with SDBS. The second is for separation of Pd(II). Prior to flotation, the solution of PdCl(2-)(4) and PtCl(2-)(6) is heated with ammonium acetate to convert PdCl(2-)(4) into Pd(NH(3))(2+)(4). The chloro-complex of Pt(IV) is unaffected. The complex cation, Pd(NH(3))(2+)(4), is then selectively floated with SDBS. The procedures are fast, simple and do not require expensive reagents and apparatus.

Separation of Co(II) from dilute aqueous solutions by precipitate and adsorbing colloid flotation

International Nuclear Information System (INIS)

Aziz, M.; Benyamin, K.; Shakir, K.; Atomic Energy Establishment, Cairo

1993-01-01

Ion, precipitate and adsorbing colloid flotation of cobalt(II) have been investigated at different pH values, using N-dodecylpyridinium chloride (DPCl). A strong cationic surfactant, and sodium lauryl sulfate (NaLS), a strong anionic surfactant, as collectors. In case of adsorbing colloid flotation, hydrous manganese dioxide was used as an adsorbent. The precipitate flotation curves experimentally obtained with the two tested collectors were compared with the corresponding theoretical one calculated from the data published for Co(II) hydrolysis. The effects of the collector concentration, ageing of the water-MnO 2 -Co(II) system, bubbling time period, cobalt(II) concentration and foreign salts on the percent removal of Co(II) by adsorbing colloid flotation using DPCl as collector were determined. Removals approaching 100% could be achieved under the optimum conditions. (author) 44 refs.; 6 figs

Flotation as a remediation technique for heavily polluted dredged material. 1. A feasibility study.

Science.gov (United States)

Cauwenberg, P; Verdonckt, F; Maes, A

1998-01-19

The flotation behaviour of highly polluted dredged material was investigated at different pH values by mechanical agitated (Denver) flotation. Up to 80% of cadmium, copper, lead and zinc could be concentrated in the froth layer which represented only 30% of the total mass. The maximum specificity for heavy metals, defined as the concentrating factor, was obtained at pH 8-9. The maximum recovery of heavy metals on the other hand was found to be reached at elevated pH values (pH 12). In addition the specificity of the flotation process for the transition metals could be assigned to their presence as metal sulphides in the dredged material. However, the interaction with organic matter is an important factor in determining their flotability. The carbonate fraction was irrelevant for the flotation behaviour of heavy metals.

Topographical features of physiographic unit borders on reef flat in fringing reefs

OpenAIRE

Nakai, Tatsuo

2007-01-01

In coral reef ecosystem spatial structure of 10^1-10^3m scale provide very important aspect in coral reef conservation. Nakai (2007) showed that physiographic unit (PGU) could be set as well as zonation on reef flat of fringing reef. The borders of PGUs delimiting it from the open sea or an adjacent PGU are constituted by landforms such as reef crest or channels. In this article the landforms becoming the borders of PGUs were discussed and the PGU property was clarified.

Study of effect of slime processed by ultrasonic on flotation reagent

Energy Technology Data Exchange (ETDEWEB)

Kang, W.; Wang, H.; Hu, J. [Heilongjiang Institute of Science and Technology, Harbin (China)

2006-12-15

The changes of wetting heat, oil film thickness, contact angle and absorptive capacity of slime and kerosene before and after ultrasonic treatment were studied by Setaram calorimeter, DCAT21 gauge and a light meter. Batch flotation tests were made. The results show that: the wetting heat from slime and kerosene increases after ultrasonic treatment by 45.85%; the average oil film thickness is reduced by 38.84%; the contact angle of slime and kerosene decreases by 33.56{sup o}; and the absorptive capacity of slime in kerosene decreases by 30.40%. The consumption of flotation reagent after ultrasonic treatment was reduced by 75% while the yield of clean coal was the same. The study shows that ultrasonic treatment decreases the consumption of reagent and increases the efficiency and selectivity of flotation. 8 refs., 3 figs., 4 tabs.

Say what? Coral reef sounds as indicators of community assemblages and reef conditions

Science.gov (United States)

Mooney, T. A.; Kaplan, M. B.

2016-02-01

Coral reefs host some of the highest diversity of life on the planet. Unfortunately, reef health and biodiversity is declining or is threatened as a result of climate change and human influences. Tracking these changes is necessary for effective resource management, yet estimating marine biodiversity and tracking trends in ecosystem health is a challenging and expensive task, especially in many pristine reefs which are remote and difficult to access. Many fishes, mammals and invertebrates make sound. These sounds are reflective of a number of vital biological processes and are a cue for settling reef larvae. Biological sounds may be a means to quantify ecosystem health and biodiversity, however the relationship between coral reef soundscapes and the actual taxa present remains largely unknown. This study presents a comparative evaluation of the soundscape of multiple reefs, naturally differing in benthic cover and fish diversity, in the U.S. Virgin Islands National Park. Using multiple recorders per reef we characterized spacio-temporal variation in biological sound production within and among reefs. Analyses of sounds recorded over 4 summer months indicated diel trends in both fish and snapping shrimp acoustic frequency bands with crepuscular peaks at all reefs. There were small but statistically significant acoustic differences among sites on a given reef raising the possibility of potentially localized acoustic habitats. The strength of diel trends in lower, fish-frequency bands were correlated with coral cover and fish density, yet no such relationship was found with shrimp sounds suggesting that fish sounds may be of higher relevance to tracking certain coral reef conditions. These findings indicate that, in spite of considerable variability within reef soundscapes, diel trends in low-frequency sound production reflect reef community assemblages. Further, monitoring soundscapes may be an efficient means of establishing and monitoring reef conditions.

A new microcolumn flotation cell for determining the wettability and floatability of minerals.

Science.gov (United States)

Ozkan, A; Yekeler, M

2003-05-15

Flotation is one of the most important physicochemical processes for mineral separations and other recovery operations. Flotation machines have been developed since the beginning of the 19th century and are still under intensive research and development. The cell we devised is a combination of the Canadian column flotation cell and the Partridge-Smith cell. The materials used for the construction of the new cell are cheap and use available laboratory accessories and aquarium materials. The cell functions well in terms of its scale, control, and sample requirement. It can be used both in the laboratory for research and in classrooms for demonstrations of experiments. Some of the data obtained by the flotation method using this cell are in good agreement with data measured independently on the same minerals by the contact angles method. The critical values of surface tension of wetting (gamma(c)) for talc, sulfur, and chemically treated surfaces of calcite and barite obtained by the contact angle measurements were 31, 26, 30.5, and 31.2 mN/m, respectively. On the other hand, the gamma(c) values of those minerals, obtained using our new designed flotation cell, were 30, 28, 31.4, and 34.5 mN/m, respectively. The measurements obtained in our experiment are also comparable to those previously published for the same minerals.

Processing of low-grade uranium ores

International Nuclear Information System (INIS)

Michel, P.

1975-01-01

Four types of low grade ores are studied. Low grade ores which must be extracted because they are enclosed in a normal grade deposit. Heap leaching is the processing method which is largely used. It allows to obtain solutions or preconcentrates which may be delivered at the nearest plant. Normal grade ores contained in a low amplitude deposit which can be processed using leaching as far as the operation does not need any large expensive equipment. Medium grade ores in medium amplitude deposits to which a simplified conventional process can be applied using fast heap leaching. Low grade ores in large deposits. The processing possibilities leading to use in place leaching are explained. The operating conditions of the method are studied (leaching agent, preparation of the ore deposit to obtain a good tightness with regard to the hydrological system and to have a good contact between ore and reagent) [fr

Dynamic Modeling and Real-Time Monitoring of Froth Flotation

Directory of Open Access Journals (Sweden)

Khushaal Popli

2015-08-01

Full Text Available A dynamic fundamental model was developed linking processes from the microscopic scale to the equipment scale for batch froth flotation. State estimation, fault detection, and disturbance identification were implemented using the extended Kalman filter (EKF, which reconciles real-time measurements with dynamic models. The online measurements for the EKF were obtained through image analysis of froth images that were captured and analyzed using the commercial package VisioFroth (Metsor Minerals. The extracted image features were then correlated to recovery using principal component analysis and partial least squares regression. The performance of real-time state estimation and fault detection was validated using batch flotation of pure galena at various operating conditions. The image features that were strongly representative of recovery were identified, and calibration and validation were performed against off-line measurements of recovery. The EKF successfully captured the dynamics of the process by updating the model states and parameters using the online measurements. Finally, disturbances in the air flow rate and impeller speed were introduced into the system, and the dynamic behavior of the flotation process was successfully tracked and the disturbances were identified using state estimation.

Flotation performances and adsorption mechanism of α-hydroxyoctyl phosphinic acid to cassiterite

International Nuclear Information System (INIS)

Li, Fangxu; Zhong, Hong; Zhao, Gang; Wang, Shuai; Liu, Guangyi

2015-01-01

Highlights: • Flotation of cassiterite is carried out using a new collector HPA. • Phosphorous and oxygen of HPA forms chelation with Sn. • HPA exhibits good selectivity to cassiterite against magnetite and hematite. • HPA chemisorbs on cassiterite surface by form of Sn–P and Sn–O–P bond. - Abstract: In this paper, the flotation performances and adsorption mechanism of α-hydroxyoctyl phosphinic acid (HPA) to cassiterite were investigated by adsorption experiments, micro-flotation tests, zeta potential measurements, Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) analyses. The micro-flotation results indicated that compared with styrene phosphonic acid (SPA), diphosphonic acid (DPA), benzohydroxamic acid (BHA) and salicylhydroxamic acid (SHA), HPA exhibited excellent collecting power to cassiterite and superior selectivity against magnetite or hematite over a wide pH range. The results of adsorption experiments and zeta potential deduced that HPA chemisorb on cassiterite surfaces. The results of FTIR inferred HPA chemisorb onto cassiterite surfaces through its P and O atoms with the P–H and O–H bonds broken. XPS analysis further demonstrated HPA react with Sn species by formation of Sn–O–P and Sn–P bond.

Determination of molybdenum (VI) in sea water with preliminary concentration by the method of ion flotation

International Nuclear Information System (INIS)

Andreeva, I. Yu.; Drapchinskaya, O.L.; Lebedeva, L.I.

1985-01-01

The purpose of this paper is to assess the feasibility of using the method of ion flotation for the concentration of microamounts of molybdenum (VI) during determination in sea water. The ion flotation method is used for the purification of industrial sewage from the ions of nonferrous metals, including molybdenum (VI) with its content of up to 50 mg/liter. A 1.10 -4 M solution of sodium molybdate in 0.1M NaOH was used. The effect of different factors on the ion flotation process of molybdenum (VI) was investigated: pH of the solution, flotation times, concentrations of surface-active substances (SAS), molybdenum (IV), extraneous salts. Data presented show that the ion flotation method in conjunction with the photometric method of determining molybdenum with brompyrogallol red (BPR) and cetylpridinium chloride (CP) (limit of detection 0.02 micrograms/liter) allows the content of molybdenum (VI) in sea water to be established with sufficient reliability and reproducibility

Flotation removal of the microalga Nannochloropsis sp. using Moringa protein-oil emulsion: A novel green approach.

Science.gov (United States)

Kandasamy, Ganesan; Shaleh, Sitti Raehanah Muhamad

2018-01-01

A new approach to recover microalgae from aqueous medium using a bio-flotation method is reported. The method involves utilizing a Moringa protein extract - oil emulsion (MPOE) for flotation removal of Nannochloropsis sp. The effect of various factors has been assessed using this method, including operating parameters such as pH, MPOE dose, algae concentration and mixing time. A maximum flotation efficiency of 86.5% was achieved without changing the pH condition of algal medium. Moreover, zeta potential analysis showed a marked difference in the zeta potential values when increase the MPOE dose concentration. An optimum condition of MPOE dosage of 50ml/L, pH 8, mixing time 4min, and a flotation efficiency of greater than 86% was accomplished. The morphology of algal flocs produced by protein-oil emulsion flocculant were characterized by microscopy. This flotation method is not only simple, but also an efficient method for harvesting microalgae from culture medium. Copyright © 2017 Elsevier Ltd. All rights reserved.

Statistical Evaluation and Optimization of Factors Affecting the Leaching Performance of Copper Flotation Waste

Directory of Open Access Journals (Sweden)

Semra Çoruh

2012-01-01

Full Text Available Copper flotation waste is an industrial by-product material produced from the process of manufacturing copper. The main concern with respect to landfilling of copper flotation waste is the release of elements (e.g., salts and heavy metals when in contact with water, that is, leaching. Copper flotation waste generally contains a significant amount of Cu together with trace elements of other toxic metals, such as Zn, Co, and Pb. The release of heavy metals into the environment has resulted in a number of environmental problems. The aim of this study is to investigate the leaching characteristics of copper flotation waste by use of the Box-Behnken experimental design approach. In order to obtain the optimized condition of leachability, a second-order model was examined. The best leaching conditions achieved were as follows: pH = 9, stirring time = 5 min, and temperature = 41.5°C.

Statistical evaluation and optimization of factors affecting the leaching performance of copper flotation waste.

Science.gov (United States)

Coruh, Semra; Elevli, Sermin; Geyikçi, Feza

2012-01-01

Copper flotation waste is an industrial by-product material produced from the process of manufacturing copper. The main concern with respect to landfilling of copper flotation waste is the release of elements (e.g., salts and heavy metals) when in contact with water, that is, leaching. Copper flotation waste generally contains a significant amount of Cu together with trace elements of other toxic metals, such as Zn, Co, and Pb. The release of heavy metals into the environment has resulted in a number of environmental problems. The aim of this study is to investigate the leaching characteristics of copper flotation waste by use of the Box-Behnken experimental design approach. In order to obtain the optimized condition of leachability, a second-order model was examined. The best leaching conditions achieved were as follows: pH = 9, stirring time = 5 min, and temperature = 41.5 °C.

Filtration aids in uranium ore processing

International Nuclear Information System (INIS)

Ford, H.L.; Levine, N.M.; Risdon, A.R.

1975-01-01

A process of improving the filtration efficiency and separation of uranium ore pulps obtained by carbonate leaching of uranium ore which comprises treating said ore pulps with an aqueous solution of hydroxyalkyl guar selected from the group consisting of hydroxyethyl and hydroxypropyl guar in the amount of 0.1 and 2.0 pounds of hydroxyalkyl guar per ton of uranium ore

Reef Development on Artificial Patch Reefs in Shallow Water of Panjang Island, Central Java

Science.gov (United States)

Munasik; Sugiyanto; Sugianto, Denny N.; Sabdono, Agus

2018-02-01

Reef restoration methods are generally developed by propagation of coral fragments, coral recruits and provide substrate for coral attachment using artificial reefs (ARs). ARs have been widely applied as a tool for reef restoration in degraded natural reefs. Successful of coral restoration is determined by reef development such as increasing coral biomass, natural of coral recruits and fauna associated. Artificial Patch Reefs (APRs) is designed by combined of artificial reefs and coral transplantation and constructed by modular circular structures in shape, were deployed from small boats by scuba divers, and are suitable near natural reefs for shallow water with low visibility of Panjang Island, Central Java. Branching corals of Acropora aspera, Montipora digitata and Porites cylindrica fragments were transplanted on to each module of two units of artificial patch reefs in different periods. Coral fragments of Acropora evolved high survival and high growth, Porites fragments have moderate survival and low growth, while fragment of Montipora show in low survival and moderate growth. Within 19 to 22 months of APRs deployment, scleractinian corals were recruited on the surface of artificial patch reef substrates. The most recruits abundant was Montastrea, followed by Poritids, Pocilloporids, and Acroporids. We conclude that artificial patch reefs with developed by coral fragments and natural coral recruitment is one of an alternative rehabilitation method in shallow reef with low visibility.

Hydrogen Reduction of Hematite Ore Fines to Magnetite Ore Fines at Low Temperatures

Directory of Open Access Journals (Sweden)

Wenguang Du

2017-01-01

Full Text Available Surplus coke oven gases (COGs and low grade hematite ores are abundant in Shanxi, China. Our group proposes a new process that could simultaneously enrich CH4 from COG and produce separated magnetite from low grade hematite. In this work, low-temperature hydrogen reduction of hematite ore fines was performed in a fixed-bed reactor with a stirring apparatus, and a laboratory Davis magnetic tube was used for the magnetic separation of the resulting magnetite ore fines. The properties of the raw hematite ore, reduced products, and magnetic concentrate were analyzed and characterized by a chemical analysis method, X-ray diffraction, optical microscopy, and scanning electron microscopy. The experimental results indicated that, at temperatures lower than 400°C, the rate of reduction of the hematite ore fines was controlled by the interfacial reaction on the core surface. However, at temperatures higher than 450°C, the reaction was controlled by product layer diffusion. With increasing reduction temperature, the average utilization of hydrogen initially increased and tended to a constant value thereafter. The conversion of Fe2O3 in the hematite ore played an important role in the total iron recovery and grade of the concentrate. The grade of the concentrate decreased, whereas the total iron recovery increased with the increasing Fe2O3 conversion.

Coral reef soundscapes may not be detectable far from the reef

Science.gov (United States)

Kaplan, Maxwell B.; Mooney, T. Aran

2016-08-01

Biological sounds produced on coral reefs may provide settlement cues to marine larvae. Sound fields are composed of pressure and particle motion, which is the back and forth movement of acoustic particles. Particle motion (i.e., not pressure) is the relevant acoustic stimulus for many, if not most, marine animals. However, there have been no field measurements of reef particle motion. To address this deficiency, both pressure and particle motion were recorded at a range of distances from one Hawaiian coral reef at dawn and mid-morning on three separate days. Sound pressure attenuated with distance from the reef at dawn. Similar trends were apparent for particle velocity but with considerable variability. In general, average sound levels were low and perhaps too faint to be used as an orientation cue except very close to the reef. However, individual transient sounds that exceeded the mean values, sometimes by up to an order of magnitude, might be detectable far from the reef, depending on the hearing abilities of the larva. If sound is not being used as a long-range cue, it might still be useful for habitat selection or other biological activities within a reef.

Effect of foamability index of short chain alkyl amines on flotation of quartz

Directory of Open Access Journals (Sweden)

Szczerkowska Sabina

2016-01-01

Full Text Available Amines can be used for flotation of various minerals, especially quartz. The flotation efficiency of quartz depends on the amine type and dose. It was proved that the shorter alkyl amine, higher amine concentration has to be used to recover quartz at the same level. In flotation amines play a role of both collectors and frothers. The ability of a amine to collect particles can be expressed in the form of contact angle, while the foaming properties by different parameters including dynamic foamability index (DFI and critical coalescence concentration (CCC. Determination of DFI and CCC requires advanced techniques and methods. Therefore, in this paper a rapid and facile method for determination of foaming properties of amines and also other surfactants was used. It was based on measuring the initial foam and froth heights in a conventional flotation machine at different concentrations of surfactants. The foam height-concentration curve was described by utilizing an empirical equation which was based on one-adjustable parameter called the foamability index (FI. In this work the foamability index was determined for butylamine (ButNH2, hexylamine (HexNH2 and octylamine (OctNH2 as examples of short chain alkyl amines. The determined foamability indices were 92, 12 and 4 mg/dm3 for ButNH2, HexNH2 and OctNH2, respectively. It was shown that when the flotation results of quartz were presented in the form of recovery versus normalized amine concentration in relation to the foamability index (c/FI, all the experimental data points converged to one curve. It indicates that amines act similarly but at different concentrations expressed as FI. The foamability index seems to be a useful parameter for characterizing any flotation frother.

Reef odor: a wake up call for navigation in reef fish larvae.

Directory of Open Access Journals (Sweden)

Claire B Paris

Full Text Available The behavior of reef fish larvae, equipped with a complex toolbox of sensory apparatus, has become a central issue in understanding their transport in the ocean. In this study pelagic reef fish larvae were monitored using an unmanned open-ocean tracking device, the drifting in-situ chamber (DISC, deployed sequentially in oceanic waters and in reef-born odor plumes propagating offshore with the ebb flow. A total of 83 larvae of two taxonomic groups of the families Pomacentridae and Apogonidae were observed in the two water masses around One Tree Island, southern Great Barrier Reef. The study provides the first in-situ evidence that pelagic reef fish larvae discriminate reef odor and respond by changing their swimming speed and direction. It concludes that reef fish larvae smell the presence of coral reefs from several kilometers offshore and this odor is a primary component of their navigational system and activates other directional sensory cues. The two families expressed differences in their response that could be adapted to maintain a position close to the reef. In particular, damselfish larvae embedded in the odor plume detected the location of the reef crest and swam westward and parallel to shore on both sides of the island. This study underlines the critical importance of in situ Lagrangian observations to provide unique information on larval fish behavioral decisions. From an ecological perspective the central role of olfactory signals in marine population connectivity raises concerns about the effects of pollution and acidification of oceans, which can alter chemical cues and olfactory responses.

Sampling of ore

International Nuclear Information System (INIS)

Boehme, R.C.; Nicholas, B.L.

1987-01-01

This invention relates to a method of an apparatus for ore sampling. The method includes the steps of periodically removing a sample of the output material of a sorting machine, weighing each sample so that each is of the same weight, measuring a characteristic such as the radioactivity, magnetivity or the like of each sample, subjecting at least an equal portion of each sample to chemical analysis to determine the mineral content of the sample and comparing the characteristic measurement with desired mineral content of the chemically analysed portion of the sample to determine the characteristic/mineral ratio of the sample. The apparatus includes an ore sample collector, a deflector for deflecting a sample of ore particles from the output of an ore sorter into the collector and means for moving the deflector from a first position in which it is clear of the particle path from the sorter to a second position in which it is in the particle path at predetermined time intervals and for predetermined time periods to deflect the sample particles into the collector. The apparatus conveniently includes an ore crusher for comminuting the sample particle, a sample hopper means for weighing the hopper, a detector in the hopper for measuring a characteristic such as radioactivity, magnetivity or the like of particles in the hopper, a discharge outlet from the hopper and means for feeding the particles from the collector to the crusher and then to the hopper

Synthesis of nanoparticle emulsion collector HNP and its application in microfine chalcopyrite flotation

Science.gov (United States)

He, G. C.; Ding, J.; Huang, C. H.; Kang, Q.

2018-01-01

Hydrophobic polystyrene nanoparticles bearing thiazole groups named HNP were used as collectors to improve recovery of microfine chalcopyrite in flotation. HNP adsorbs onto microfine particles selectively, which were modified hydrophobically to induce flotation effectively. Particle size and scanning electron microscope analysis for HNP show that HNP is a spherical nano particles with small size, uniform distribution and good dispersion. Infrared spectrum analysis for HNP proved that functional monomer 2-mercapto styrene acrylic thiazole was bonded chemically onto styrene. Flotation test results indicate that HNP is the right collector of chalcopyrite. Especially, the recovery of chalcopyrite is higher than 95% in neutral and acid media. FTIR results reveal that the flotation selectivity of collector HNP is due to strong chemical absorption onto chalcopyrite surface. Zeta potential analysis shows that the zeta potential of chalcopyrite decreased more quickly after interaction with HNP with the increase of pulp pH value, confirming that collector HNP is an anionic collector. Scanning electron microscope conform that HNP has good selective adsorption on chalcopyrite.

Molybdenite recovery by column flotation in the Byproduct Recovery Plant of UCIL, Jaduguda

International Nuclear Information System (INIS)

Rao, G.V.; Sastri, S.R.S.

1998-01-01

Molybdenite is recovered at Byproduct Recovery Plant (BRP) of Uranium Corporation of India Ltd., Jaduguda, from the bulk concentrate of copper, nickel and molybdenum by differential flotation using sodium sulphide as the depressant for copper, nickel and iron sulphide minerals in combination with sodium silicate, after five cleanings in mechanical cells. The eventual molybdenite concentrate assays between 35% Mo to 40% Mo. Column flotation studies on the same bulk concentrate at the plant site indicated that concentrate containing 44% Mo can be obtained in single stage with above 95% recoveries from a feed containing around 7% Mo, 16% Cu and 10% Ni. The column flotation studies with the sodium hydrogen sulphide in place of sodium sulphide also gave more or less the same results but the contamination of copper and nickel in the molybdenite concentrate is minimum in the product obtained with sodium sulphide. A single flotation column was found sufficient to replace five cleaning stages in mechanical cells in the lone commercial molybdenite recovery plant in the country. (author)

Recovery process of the mineral sphalerite of Chaabet El Hamra's deposit (Algeria)

Science.gov (United States)

Begar, A.; Djeghlal, M.

2012-06-01

The present study rests on the treatment's process optimization by flotation of the Chaabet El Hamra's zinc ore (Algeria), for the optimization parameters relating to the production. The choice of parameter to optimize for flotation, and the arrangements and the scheme's initial flotation, while considering the studies already undertaken, all this has enabled us to better focus our work, while minimizing the consumption of reagents in different tests, This has resulted in successful outcomes.

Difference of ore-bearing and non-ore-bearing pegmatite in the Guangshigou area and its research significance

International Nuclear Information System (INIS)

Zuo Wenqian; Zhang Zhanshi; Sha Yazhou; Rao Chaojun

2011-01-01

Guangshigou uranium deposit is one of the typical granite-pegmatite uranium deposits in China, the ore-body are located in the density zone of the outside contact zone of granite pluton. To distinguish the ore-bearing and Non-ore-bearing pegmatite is one of the most practices and have great significance for the effect of mineral exploration. Based on the field investigation and former research results, contrast research on the characteristics of the pegmatite on petrology, geophysical, geochemistry and stable isotopes have been carried out. It is pointed out that the ore-bearing pegmatite differ from the non-ore-bearing one from macro-and-micro-view in Guangshigou Uranium deposits, the main characteristics are summarized; the macro-and-micro signs are established, the genetic difference between the ore-bearing and non-ore-bearing pegmatite are discussed primarily. The achievements would be helpful for prospecting and researching of this type uranium deposits in China. (authors)

Influence of acid/ore relation in the uranium-silicate ore treatment

International Nuclear Information System (INIS)

Antaki, C.; Cipriani, M.; Bruno, J.B.

1985-01-01

The estimation of acid addition effect (Kg of H 2 SO 4 /t of ore) in uranium extraction from an uranium-silicate ore, with a view to the control of silica concentration in leach under 0,6 g/l is presented. The analysis was effected based on bench-scale tests, with different quantities of sulfuric acid addition. (Author) [pt

Processing of low grade uranium ores

International Nuclear Information System (INIS)

Michel, P.

1978-10-01

Four types of low-grade ores are studied: (1) Low-grade ores that must be extracted because they are enclosed in a normal-grade deposit. Heap leaching is the processing method which is largely used. (2) Normal-grade ores contained in low-amplitude deposits. They can be processed using in-place leaching as far as the operation does not need any large and expensive equipment. (3) Medium-grade ores in medium-amplitude deposits. A simplified conventional process can be applied using fast heap leaching. (4) Low-grade ores in large deposits. The report explains processing possibilities leading in most cases to the use of in-place leaching. The operating conditions of this method are laid out, especially the selection of the leaching agents and the preparation of the ore deposit

NOAA Coral Reef Watch Larval Connectivity, Florida Reef Tract

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Climate change threatens even the best-protected and most remote reefs. Reef recovery following catastrophic disturbance usually requires disturbed sites be reseeded...

High-rate behaviour of iron ore pellet

Science.gov (United States)

Gustafsson, Gustaf; Häggblad, Hans-Åke; Jonsén, Pär; Nishida, Masahiro

2015-09-01

Iron ore pellets are sintered, centimetre-sized spheres of ore with high iron content. Together with carbonized coal, iron ore pellets are used in the production of steel. In the transportation from the pelletizing plants to the customers, the iron ore pellets are exposed to different loading situations, resulting in degradation of strength and in some cases fragmentation. For future reliable numerical simulations of the handling and transportation of iron ore pellets, knowledge about their mechanical properties is needed. This paper describes the experimental work to investigate the dynamic mechanical properties of blast furnace iron ore pellets. To study the dynamic fracture of iron ore pellets a number of split Hopkinson pressure bar tests are carried out and analysed.

Studies on uranium ore processing

International Nuclear Information System (INIS)

Suh, I.S.; Chun, J.K.; Park, S.W.; Choi, S.J.; Lee, C.H.; Chung, M.K.; Lim, J.K.

1983-01-01

For the exploitation of domestic uranium ore deposit, comprehensive studies on uranium ore processing of the Geum-San pit ore are carried out. Physical and chemical characteristics of the Geum-San ore are similar to those of Goe-San ore and the physical beneficiation could not be applicable. Optimum operating conditions such as uranium leaching, solid-liquid separation, solvent extraction and precipitation of yellow cake are found out and the results are confirmed by the continous operation of the micro-plant with the capacity of 50Kg, ore/day. In order to improve the process of ore milling pilot plant installed recently, the feasibility of raffinate-recycle and the precipitation methods of yellow cake are intensively examined. It was suggested that the raffinate-recycle in the leaching of filtering stage could be reduced the environmental contamination and the peroxide precipitation technique was applicable to improve the purity of yellow cake. The mechanism and conditions the third phase formation are thoroughly studied and confirmed by chemical analysis of the third phase actually formed during the operation of pilot plant. The major constituents of the third phase are polyanions such as PMosub(12)Osub(40)sup(3-) or SiMosub(12)Osub(40)sup(4-). And the formation of these polyanions could be reduced by the control of redox potential and the addition of modifier. (Author)

Accuracy of egg flotation throughout incubation to determine embryo age and incubation day in waterbird nests

Science.gov (United States)

Ackerman, Joshua T.; Eagles-Smith, Collin A.

2010-01-01

Floating bird eggs to estimate their age is a widely used technique, but few studies have examined its accuracy throughout incubation. We assessed egg flotation for estimating hatch date, day of incubation, and the embryo's developmental age in eggs of the American Avocet (Recurvirostra americana), Black-necked Stilt (Himantopus mexicanus), and Forster's Tern (Sterna forsteri). Predicted hatch dates based on egg flotation during our first visit to a nest were highly correlated with actual hatch dates (r = 0.99) and accurate within 2.3 ± 1.7 (SD) days. Age estimates based on flotation were correlated with both day of incubation (r = 0.96) and the embryo's developmental age (r = 0.86) and accurate within 1.3 ± 1.6 days and 1.9 ± 1.6 days, respectively. However, the technique's accuracy varied substantially throughout incubation. Flotation overestimated the embryo's developmental age between 3 and 9 days, underestimated age between 12 and 21 days, and was most accurate between 0 and 3 days and 9 and 12 days. Age estimates based on egg flotation were generally accurate within 3 days until day 15 but later in incubation were biased progressively lower. Egg flotation was inaccurate and overestimated embryo age in abandoned nests (mean error: 7.5 ± 6.0 days). The embryo's developmental age and day of incubation were highly correlated (r = 0.94), differed by 2.1 ± 1.6 days, and resulted in similar assessments of the egg-flotation technique. Floating every egg in the clutch and refloating eggs at subsequent visits to a nest can refine age estimates.

Kinetics of Cu (II) separation by ion flotation techniques, in cells with flexible spargers

International Nuclear Information System (INIS)

Reyes, M.; Tavera, F. J.; Escudero, R.; Patino, F.; Salinas, E.; Rivera, I.

2010-01-01

This research studies and experimentally determines the kinetic parameters and effect of modifying the hydrodynamics and chemical conditions of the air-liquid dispersions during the Cu (II) extraction by ion flotation techniques in cells with porous spargers. Results show that the elimination of Cu (II) from solution can be carried out by ion flotation in one stage, obtaining efficiencies of 68% and 56% for the flat and cylindrical sparger respectively with a xanthate concentration of 0,02 g/l. In multistage systems five cells, recoveries over 92 % were achieved for both sparger geometries. The behavior of the flotation apparent kinetic constant is linear to the parameters that characterize dispersion (Jg, eg y Db), until a point is achieved where the process instability makes the system inoperable. The results show that removing base metal ions by ion flotation is strongly affected by the following factors: collector concentration [C], Jg, eg, Db, Jl and Sb. (Author) 20 refs

Numerical Simulations of Two-Phase Flow in a Self-Aerated Flotation Machine and Kinetics Modeling

KAUST Repository

Fayed, Hassan E.; Ragab, Saad

2015-01-01

A new boundary condition treatment has been devised for two-phase flow numerical simulations in a self-aerated minerals flotation machine and applied to a Wemco 0.8 m3 pilot cell. Airflow rate is not specified a priori but is predicted by the simulations as well as power consumption. Time-dependent simulations of two-phase flow in flotation machines are essential to understanding flow behavior and physics in self-aerated machines such as the Wemco machines. In this paper, simulations have been conducted for three different uniform bubble sizes (db = 0.5, 0.7 and 1.0 mm) to study the effects of bubble size on air holdup and hydrodynamics in Wemco pilot cells. Moreover, a computational fluid dynamics (CFD)-based flotation model has been developed to predict the pulp recovery rate of minerals from a flotation cell for different bubble sizes, different particle sizes and particle size distribution. The model uses a first-order rate equation, where models for probabilities of collision, adhesion and stabilization and collisions frequency estimated by Zaitchik-2010 model are used for the calculation of rate constant. Spatial distributions of dissipation rate and air volume fraction (also called void fraction) determined by the two-phase simulations are the input for the flotation kinetics model. The average pulp recovery rate has been calculated locally for different uniform bubble and particle diameters. The CFD-based flotation kinetics model is also used to predict pulp recovery rate in the presence of particle size distribution. Particle number density pdf and the data generated for single particle size are used to compute the recovery rate for a specific mean particle diameter. Our computational model gives a figure of merit for the recovery rate of a flotation machine, and as such can be used to assess incremental design improvements as well as design of new machines.

Numerical Simulations of Two-Phase Flow in a Self-Aerated Flotation Machine and Kinetics Modeling

Directory of Open Access Journals (Sweden)

Hassan Fayed

2015-03-01

Full Text Available A new boundary condition treatment has been devised for two-phase flow numerical simulations in a self-aerated minerals flotation machine and applied to a Wemco 0.8 m3 pilot cell. Airflow rate is not specified a priori but is predicted by the simulations as well as power consumption. Time-dependent simulations of two-phase flow in flotation machines are essential to understanding flow behavior and physics in self-aerated machines such as the Wemco machines. In this paper, simulations have been conducted for three different uniform bubble sizes (db = 0.5, 0.7 and 1.0 mm to study the effects of bubble size on air holdup and hydrodynamics in Wemco pilot cells. Moreover, a computational fluid dynamics (CFD-based flotation model has been developed to predict the pulp recovery rate of minerals from a flotation cell for different bubble sizes, different particle sizes and particle size distribution. The model uses a first-order rate equation, where models for probabilities of collision, adhesion and stabilization and collisions frequency estimated by Zaitchik-2010 model are used for the calculation of rate constant. Spatial distributions of dissipation rate and air volume fraction (also called void fraction determined by the two-phase simulations are the input for the flotation kinetics model. The average pulp recovery rate has been calculated locally for different uniform bubble and particle diameters. The CFD-based flotation kinetics model is also used to predict pulp recovery rate in the presence of particle size distribution. Particle number density pdf and the data generated for single particle size are used to compute the recovery rate for a specific mean particle diameter. Our computational model gives a figure of merit for the recovery rate of a flotation machine, and as such can be used to assess incremental design improvements as well as design of new machines.

Numerical Simulations of Two-Phase Flow in a Self-Aerated Flotation Machine and Kinetics Modeling

KAUST Repository

Fayed, Hassan E.

2015-03-30

A new boundary condition treatment has been devised for two-phase flow numerical simulations in a self-aerated minerals flotation machine and applied to a Wemco 0.8 m3 pilot cell. Airflow rate is not specified a priori but is predicted by the simulations as well as power consumption. Time-dependent simulations of two-phase flow in flotation machines are essential to understanding flow behavior and physics in self-aerated machines such as the Wemco machines. In this paper, simulations have been conducted for three different uniform bubble sizes (db = 0.5, 0.7 and 1.0 mm) to study the effects of bubble size on air holdup and hydrodynamics in Wemco pilot cells. Moreover, a computational fluid dynamics (CFD)-based flotation model has been developed to predict the pulp recovery rate of minerals from a flotation cell for different bubble sizes, different particle sizes and particle size distribution. The model uses a first-order rate equation, where models for probabilities of collision, adhesion and stabilization and collisions frequency estimated by Zaitchik-2010 model are used for the calculation of rate constant. Spatial distributions of dissipation rate and air volume fraction (also called void fraction) determined by the two-phase simulations are the input for the flotation kinetics model. The average pulp recovery rate has been calculated locally for different uniform bubble and particle diameters. The CFD-based flotation kinetics model is also used to predict pulp recovery rate in the presence of particle size distribution. Particle number density pdf and the data generated for single particle size are used to compute the recovery rate for a specific mean particle diameter. Our computational model gives a figure of merit for the recovery rate of a flotation machine, and as such can be used to assess incremental design improvements as well as design of new machines.

Study of solid and liquid behavior in large copper flotation cells (130 m2) using radioactive tracers

International Nuclear Information System (INIS)

Diaz, F.; Jimenez, O.; Yianatos, J.; Contreras, F.

2013-01-01

The behavior of the solid and liquid phases, in large flotation cells, was characterized by means of the radioactive tracer technique. The use of radioactive tracers enabled the identification of the Residence Time Distribution, of floatable and non-floatable solid, from continuous (on-line) measuring at the output streams of the flotation cells. For this study, the proper radioactive tracers were selected and applied in order to characterize the different phases; i.e. for liquid phase Br-82 as Ammonium Bromide, for floatable solid recovered in the concentrate Cu-64, and for non-floatable solid in three particle size classes (coarse: >150 μm, intermediate: 45 μm, and fine: <45 μm), Na-24. The experimental results confirmed the strong effect of particle size on the Residence Time Distribution, and mean residence time of solids in larger flotation cells, and consequently in flotation hydrodynamics. From a hydrodynamic point of view, the experimental data confirmed that a single mechanical flotation cells, of large size, can deviate significantly from perfect mixing. The experimental work was developed in a 130 m3 industrial flotation cell of the rougher circuit at El Teniente Division, Codelco-Chile. (authors)

Condutivity effect in electro-coagulation-flotation applied to physico-chemical wastewater treatment

OpenAIRE

Francisco Javier Cuba Terán; Mário Luiz Rodrigues Foco

2007-01-01

This study reports on the effect of conductivity on the simultaneous applicability of water electrolysis , chemical coagulation and flotation fundamentals in the treatment of wastewater with large amounts of suspended matter, characterizing electro-coagulation-flotation (ECF) . Results from experiments carried out in a pilot study implanted and operated in the Laboratory of Environment Control (LCA), at the State University of Campinas in Limeira are presented. ECF was developed in an electro...

Geochemical features of the ore-bearing medium in uranium deposits in the Khiagda ore field

Science.gov (United States)

Kochkin, B. T.; Solodov, I. N.; Ganina, N. I.; Rekun, M. L.; Tarasov, N. N.; Shugina, G. A.; Shulik, L. S.

2017-09-01

The Neogene uranium deposits of the Khiagda ore field (KOF) belong to the paleovalley variety of the hydrogene type and differ from other deposits of this genetic type in the geological and geochemical localization conditions. The contemporary hydrogeochemical setting and microbiological composition of ore-bearing medium are discussed. The redox potential of the medium (Eh is as low as-400 mV) is much lower than those established at other hydrogenic deposits, both ancient Late Mesozoic and young Late Alpine, studied with the same methods in Russia, Uzbekistan, and southern Kazakhstan. The pH of subsurface water (6.86-8.13) differs in significant fluctuations both between neighboring deposits and within individual ore lodes. Hydrogen-forming and denitrifying bacteria are predominant in microbiological populations, whereas sulfate-reducing bacteria are low-active. The consideration of these factors allowed us to describe the mechanism of uranium ore conservation as resulting from the development of the cryolithic zone, which isolates ore lodes from the effect of the external medium. Carbonated water supplied from the basement along fault zones also participates in the formation of the present-day hydrogeochemical setting. Based on the features of the ore-bearing medium, we propose a method of borehole in situ acid leaching to increase the efficiency of mining in the Khiagda ore field.

Bubble feature extracting based on image processing of coal flotation froth

Energy Technology Data Exchange (ETDEWEB)

Wang, F.; Wang, Y.; Lu, M.; Liu, W. [China University of Mining and Technology, Beijing (China). Dept of Chemical Engineering and Environment

2001-11-01

Using image processing the contrast ratio between the bubble on the surface of flotation froth and the image background was enhanced, and the edges of bubble were extracted. Thus a model about the relation between the statistic feature of the bubbles in the image and the cleaned coal can be established. It is feasible to extract the bubble by processing the froth image of coal flotation on the basis of analysing the shape of the bubble. By means of processing the 51 group images sampled from laboratory column, it is thought that the use of the histogram equalization of image gradation and the medium filtering can obviously improve the dynamic contrast range and the brightness of bubbles. Finally, the method of threshold value cut and the bubble edge detecting for extracting the bubble were also discussed to describe the bubble feature, such as size and shape, in the froth image and to distinguish the froth image of coal flotation. 6 refs., 3 figs.

Application of the flotation process in the silver recovery from the wastes generated during the silvery semi-products manufacturing

OpenAIRE

B. Oleksiak; A. Blacha-Grzechnik; G. Siwiec

2012-01-01

In this work, the results of the flotation process application in the silver recovery from the wastes generated during the silvery semi-products manufacturing, are shown. The flotation process parameters, i.e. time of process, rotation frequency, gas flow rate and flotation reagents, were optimized.

Zeolitization at uranium ore manifestation

International Nuclear Information System (INIS)

Petrosyan, R.V.; Buntikova, A.F.

1981-01-01

The process of zeolitization at uranium ore manifestation is studied. A specific type of low-temperature wall endogenous alteration of rocks due to the effect of primary acid solution with low content of carbonic acid is established. Leaching of calcium from enclosing rocks and its deposition in ore-accompanying calcium zeolites is a characteristic feature of wall-metasomatosis. Formation of desmin- calcite-laumontite and quartz-fluoroapatite of vein associations, including ore minerals (uranophane and metaotenite), is genetically connected with calcium metasomatosis. On the basis of the connection of ore minerals with endogeneous process of zeolitization a conclusion can be made on endogenous origin of uranophane and metaotenite [ru

Flotation of Chalcopyrite and Molybdenite in the Presence of Organics in Water

Directory of Open Access Journals (Sweden)

Maria Sinche-Gonzalez

2016-10-01

Full Text Available One of the water constituents that has not been investigated in great detail for potential detrimental effect on mineral flotation is organic matter. This study investigates the effect of natural organic materials contained in water, such as humic, fulvic and tannic acids, on the flotation of copper and molybdenum sulphides in alkaline conditions and in concentrations similar to those found in natural waters. Results show that copper and molybdenum grades decreased with the addition of humic, tannic and fulvic acid in that order, with a larger depression of molybdenite grade and recovery. Adsorption studies using ultraviolet (UV-visible spectroscopy and X-ray photoelectron spectrometer (XPS surface analysis confirmed that these organic materials were adsorbed on the minerals surface. Complimentary analyses of froth characteristics, particle size distribution and fine particles entrainment were also conducted to explain the cause of the negative effect of these organic materials on flotation. The flotation results were explained in terms of the decrease in the hydrophobicity of the mineral surfaces due to the adsorption of hydrophilic groups in these organic materials which then prevent bubble-particle adhesion. The larger detrimental effect of humic acid is due to its higher adsorption on the minerals, high molecular weight and carbon content compared with the other organic acids used.

Performance Recognition for Sulphur Flotation Process Based on Froth Texture Unit Distribution

Directory of Open Access Journals (Sweden)

Mingfang He

2013-01-01

Full Text Available As an important indicator of flotation performance, froth texture is believed to be related to operational condition in sulphur flotation process. A novel fault detection method based on froth texture unit distribution (TUD is proposed to recognize the fault condition of sulphur flotation in real time. The froth texture unit number is calculated based on texture spectrum, and the probability density function (PDF of froth texture unit number is defined as texture unit distribution, which can describe the actual textual feature more accurately than the grey level dependence matrix approach. As the type of the froth TUD is unknown, a nonparametric kernel estimation method based on the fixed kernel basis is proposed, which can overcome the difficulty when comparing different TUDs under various conditions is impossible using the traditional varying kernel basis. Through transforming nonparametric description into dynamic kernel weight vectors, a principle component analysis (PCA model is established to reduce the dimensionality of the vectors. Then a threshold criterion determined by the TQ statistic based on the PCA model is proposed to realize the performance recognition. The industrial application results show that the accurate performance recognition of froth flotation can be achieved by using the proposed method.

Ores and Climate Change - Primary Shareholders

Science.gov (United States)

Stein, Holly J.; Hannah, Judith L.

2015-04-01

Many in the economic geology community concern themselves with details of ore formation at the deposit scale, whether tallying fluid inclusion data to get at changes in ore-forming fluids or defining structures that aid and abet mineralization. These compilations are generally aimed at interpretation of events at the site of ore formation, with the goal being assignment of the deposit to a sanctioned ore deposit model. While providing useful data, this approach is incomplete and does not, by itself, serve present-day requirements for true interdisciplinary science. The ore-forming environment is one of chaos and disequilibrium at nearly all scales (Stein, 2014). Chaos and complexity are documented by variably altered rocks, veins or disseminated mineralization with multi-generational fluid histories, erratic and unusual textures in host rocks, and the bitumen or other hydrocarbon products entwined within many ore deposits. This should give pause to our drive for more data as a means to find "the answer". The answer lies in the kind of data collected and more importantly, in the way we interpret those data. Rather than constructing an ever-increasing catalog of descriptive mutations on sanctioned ore deposit models (e.g., IOGC or Iron-Oxide Copper Gold deposits), the way forward is to link source and transport of metals, sulfur, and organic material with regional and ultimately whole Earth chemical evolution. Important experimental work provides chemical constraints in controlled and behaved environments. To these data, we add imagination and interpretation, always tying back to field observations. In this paper, several key points are made by way of ore deposit examples: (1) many IOCG deposits are outcomes of profound changes in the chemistry of the Earth's surface, in the interplay of the atmosphere, hydrosphere, biosphere, and lithosphere; (2) the redox history of Fe in deep earth may be ultimately expressed in the ore-forming sequence; and (3) the formation of