WorldWideScience

Sample records for reed bed container

  1. Removal of personal care compounds from sewage sludge in reed bed container (lysimeter) studies--effects of macrophytes.

    Science.gov (United States)

    Chen, Xijuan; Pauly, Udo; Rehfus, Stefan; Bester, Kai

    2009-10-15

    Sludge reed beds have been used for dewatering (draining and evapotranspiration) and mineralisation of sludge in Europe since 1988. Although reed beds are considered as a low cost and low contamination method in reducing volume, breaking down organic matter and increasing the density of sludge, it is not yet clear whether this enhanced biological treatment is suitable for degradation of organic micro-pollutants such as personal care products. Within this project the effect of biological sludge treatment in a reed bed on reducing the concentrations of the fragrances HHCB, AHTN, OTNE was studied as on the bactericide Triclosan. Additionally, the capacity of different macrophytes species to affect the treatment process was examined. Three different macrophyte species were compared: bulrush (Typha latifolia), reed (Phragmites australis) and reed canary grass (Phalaris arundinacea). They were planted into containers (lysimeters) with a size of 1 m x 1 m x 1 m which were filled with 20 cm gravel at the bottom and 50 cm sludge on top, into which the macrophytes were planted. During the twelve months experiment reduction of 20-30% for HHCB and AHTN, 70% for Triclosan and 70% for OTNE were determined under environmental conditions. The reduction is most likely due to degradation, since volatilization, uptake into plants and leaching are insignificant. No difference between the containers with different macrophyte species or the unplanted containers was observed. Considering the usual operation time of 10 years for reed beds, an assessment was made for the whole life time.

  2. Treatment of sludge containing nitro-aromatic compounds in reed-bed mesocosms – Water, BOD, carbon and nutrient removal

    International Nuclear Information System (INIS)

    Gustavsson, L.; Engwall, M.

    2012-01-01

    Highlights: ► It is necessary to improve existing and develop new sludge management techniques. ► One method is dewatering and biodegradation of compounds in constructed wetlands. ► The result showed high reduction of all tested parameters after treatment. ► Plants improve degradation and Phragmites australis is tolerant to xenobiotics. ► The amount of sludge could be reduced by 50–70%. - Abstract: Since the mid-1970s, Sweden has been depositing 1 million ton d.w sludge/year, produced at waste water treatment plants. Due to recent legislation this practice is no longer a viable method of waste management. It is necessary to improve existing and develop new sludge management techniques and one promising alternative is the dewatering and treatment of sludge in constructed wetlands. The aim of this study was to follow reduction of organic carbon, BOD and nutrients in an industrial sludge containing nitro-aromatic compounds passing through constructed small-scale wetlands, and to investigate any toxic effect such as growth inhibition of the common reed Phragmites australis. The result showed high reduction of all tested parameters in all the outgoing water samples, which shows that constructed wetlands are suitable for carbon and nutrient removal. The results also showed that P. australis is tolerant to xenobiotics and did not appear to be affected by the toxic compounds in the sludge. The sludge residual on the top of the beds contained low levels of organic carbon and is considered non-organic and could therefore be landfilled. Using this type of secondary treatment method, the amount of sludge could be reduced by 50–70%, mainly by dewatering and biodegradation of organic compounds.

  3. Removal of personal care compounds from sewage sludge in reed bed container (lysimeter) studies - Effects of macrophytes

    DEFF Research Database (Denmark)

    Chen, Xijuan; Pauly, Udo; Rehfus, Stefan

    2009-01-01

    as on the bactericide Triclosan. Additionally, the capacity of different macrophytes species to affect the treatment process was examined. Three different macrophyte species were compared: bulrush (Typha latifolia), reed (Phragmites australis) and reed canary grass (Phalaris arundinacea). They were planted...... into containers (lysimeters) with a size of 1 m × 1 m × 1 m which were filled with 20 cm gravel at the bottom and 50 cm sludge on top, into which the macrophytes were planted. During the twelve months experiment reduction of 20-30% for HHCB and AHTN, 70% for Triclosan and 70% for OTNE were determined under...... environmental conditions. The reduction is most likely due to degradation, since volatilization, uptake into plants and leaching are insignificant. No difference between the containers with different macrophyte species or the unplanted containers was observed. Considering the usual operation time of 10 years...

  4. System for the Reduction of Substances in Reject Water from Reed-Bed Sludge Mineralization Plants

    DEFF Research Database (Denmark)

    2004-01-01

    The invention is a system for the reduction of substances in reject water from reed-bed sludge mineralization plants (also referred to as sludge dewatering reed-beds). The systems utilizes the composition of substances in reject water from reed-beds and that of sludge to reduce substance mass from...... the reject water via recirculation into a mixed reactor and back onto the reed-beds. The mixed rector consists of a container in which sludge (that is typically loaded directly on to reed-beds) is mixed with recirculated reject water from reed-beds. The sludge mixture has a definable hydraulic retention time...... of by sending it back to the head of a wastewater treatment plant. The system has proven to reduce the mass of nitrogen, COD, and water in the reject water, and can possibly reduce phosphorus and other substances. The overall effect is a reduction in the substance recycle within a wastewater treatment plant...

  5. Purification performances of common reed beds based on the ...

    African Journals Online (AJOL)

    SARAH

    2013-11-30

    Nov 30, 2013 ... advantages, the reed bed is a solution to Beninese purification problems. Since technical service agent of ... Journal of Applied Biosciences 71:5682– 5691. ISSN 1997–5902 ..... 15N/14N ratios. Journal of Hydrology, vol. 199,.

  6. Gravity Drainage of Activated Sludge on Reed Beds

    DEFF Research Database (Denmark)

    Christensen, Morten Lykkegaard; Dominiak, Dominik Marek; Keiding, Kristian

    and operation of reed beds and the efficiencies are often lower than predicted. One reason is that the sludge quality varies from plant to plant and even within plants from time to time. No good method exists for measuring the sludge quality with respect to drainage characteristics. A new experimental method...... has therefore been developed to measure relevant quality parameters: specific cake resistance, settling velocity and cake compressibility. It has been found that activated sludge form highly compressible cake even at the low compressive pressures obtained during drainage. Numerical simulation shows......Activated sludge is a by-product from waste water treatment plants, and the water content in the sludge is high (> 90%). Among several methods to remove the water, sludge drying reed beds are often used to dewater the sludge by drainage. There is, however, no well-defined criterion for design...

  7. Role of hydraulic retention time and granular medium in microbial removal in tertiary treatment reed beds.

    Science.gov (United States)

    García, Joan; Vivar, Joan; Aromir, Maria; Mujeriego, Rafael

    2003-06-01

    The main objective of this paper is to evaluate the role of hydraulic retention time (HRT) and granular medium in faecal coliform (FC) and somatic coliphage (SC) removal in tertiary reed beds. Experiments were carried out in a pilot plant with four parallel reed beds (horizontal subsurface flow constructed wetlands), each one containing a different type of granular medium. This pilot plant is located in a wastewater treatment plant in Montcada i Reixac, near Barcelona, in northeastern Spain. The microbial inactivation ratios obtained in the different beds are compared as a function of three selected HRTs. Secondary effluent from the wastewater treatment plant was used as the influent of the pilot system. The microbial inactivation ratio ranged between 0.1 and 2.7 log-units for FC and from 0.5 to 1.7 log-units for SC in beds with coarser granular material (5-25mm), while it ranged between 0.7 and 3.4 log-units for FC and from 0.9 to 2.6 log-units for SC in the bed with finer material (2-13mm). HRT and granular medium are both key factors in microbial removal in the tertiary reed beds. The microbial inactivation ratio rises as the HRT increases until it reaches a saturation value (in general at an HRT of 3 days). The value of the microbial inactivation ratio at the saturation level depends on the granular medium contained in the bed. The specific surface area necessary to reach 2-3 log-units of FC and SC is approximately 3m(2)/person-equivalent.

  8. ADVANCES IN CLOG STATE MONITORING FOR USE IN AUTOMATED REED BED INSTALLATIONS

    Directory of Open Access Journals (Sweden)

    Theodore HUGHES-RILEY

    2014-06-01

    Full Text Available Constructed wetlands are a popular form of waste-water treatment that have proliferated across Europe and the rest of the world in recent years as an environmentally conscious form of waste water treatment. The ability to monitor the conditions in the bed and control input factors such as heating and aeration may extend the lifetime of the reed bed substantially beyond the ten year lifetime normally reached. The Autonomous Reed Bed Installation (ARBI project is an EU FP7 initiative to develop a reed bed with automated control over input parameters based on readings taken from embedded sensors. Automated remedial action may improve bed treatment efficiency, and prolong the life of the bed and avoiding the need to refurbish the bed, which is both time consuming and costly. One critical parameter to observe is the clog state of the reed bed, as this can severely impact on the efficiency of water treatment to the point of the bed becoming non-operable. Magnetic resonance (MR sensors can be a powerful tool in determining clogging levels, and has previously been explored in the literature. This work is based on a conference paper (2nd International Conference "Water resources and wetlands", 2014 and details magnetic sensors suitable for long-term embedding into a constructed wetland. Unlike previous studies this work examines a probe embedded into a wetland.

  9. Fate of xenobiotic compounds and plants activity in reed bed sludge treatment

    DEFF Research Database (Denmark)

    Chen, Xijuan; Pauli, Udo; Rehfus, Stefan

    different plants: bulrush (Typha), reed (Phragmites australis) and reed canary grass (Phalaris arundinacea) were planted into 12 containers with a size of 1m Х 1m X 1m which were builded with 20cm gravel and 50cm sludge to study the plants activity in sludge degradation process, 4 containers were left...

  10. An Evaluation of Reed Bed Technology to Dewater Army Wastewater Treatment Plant Sludge

    Science.gov (United States)

    1993-09-01

    speculated that the plants produced "root exudations" that were active against pathogens , and that the plants specifically showed an affinity for cadmium, zinc...mineralize and for pathogens to be destroyed. This downtime makes multiple beds necessary. The USEPA also reports that the major advantage of the reed...employee to regulate the sludge applications. This employee would also visually assess the beds for possible problems such as weed or insect ( aphid

  11. An introduction to constructed wetlands (reed beds) sustainable low cost wastewater treatment plants

    International Nuclear Information System (INIS)

    Ahmad, M.I.

    2005-01-01

    The use of 'conventional' wastewater treatment technology (trickling filters and activated sludge) in developing countries has often been unsuccessful due to high cost, complex operating requirements and expensive maintenance procedures. Typical examples of such projects are wastewater plants in Islamabad and Karachi. Actually the conventional systems, such as trickling filters and activated sludge plants were developed to address the concerns about organic pollution of natural water bodies in western temperate climates, rather than the reduction of organic matter as well as pathogens which is often a priority in developing countries. Pakistan, being a developing country cannot and should not follow the western technology blindly but needs the use of a ppropriate technology . Appropriate technology is defined as a treatment system which meets the following criteria: Affordable: Total amount costs, including capital, operation, maintenance and depreciation are within the user's ability to pay. Operable: Operation of the system is possible with locally available labor and support. Reliable: Effluent quality requirements can be met consistently. Currently there are a limited number of appropriate technologies for small communities, which should be considered by a community and their designers. These include conventional and non-conventional systems such as stabilization ponds or lagoons, slow sand filters, land treatment systems, and wetlands (natural or constructed). The non-conventional systems often utilize 'ecological' treatment mechanism (such as aquatic systems or wetlands) and do not have the mechanical parts or energy requirements of conventional systems. Waste Stabilization Ponds are one such solution but sometimes are constrained by land availability, topography, and are not environment friendly. In such locations, natural or constructed wetlands (Reed Beds) could provide an alternative technology. It is what we call a LOW technology, rather than HI TECH

  12. Development of the reed bed in Matsalu wetland, Estonia: responses to neotectonic land uplift, sea level changes and human influences

    Directory of Open Access Journals (Sweden)

    Mats Meriste

    2015-05-01

    Full Text Available We studied reed bed development in Matsalu wetland and the Kasari River delta, Estonia, since the late 18th century using historical schemes, topographical maps and aerial photographs. Our aim was to understand the mechanisms controlling reed distribution in Matsalu wetland, the largest coastal wetland of the eastern Baltic Sea occupying an area of about 25 km2. Natural development of the reed bed in Matsalu Bay and the Kasari delta is mainly controlled by shoreline displacement due to post-glacial neotectonic land uplift. The dredging of the Kasari delta in the 1920s–1930s caused a rapid seaward migration of reed bed communities due to the dispersal of fragmented rhizomes on the shallow sea bottom and along the canal banks reaching Matsalu Bay, while the landward parts of the former wetland were occupied by meadow communities. The expansion of the reed bed started in between the 1951s and 1970s and a maximum extent of 27 km2 was gained by the late 1970s at the peak of eutrophication. In the last decades the reed bed development has been influenced by sea level rise and increased intensity of cyclonic activity in the Baltic Sea, which has caused the deterioration of the reed bed that was weakened by eutrophication due to nutrient inflow from agricultural landscapes mainly in the 1960s–1980s.

  13. Gas composition of sludge residue profiles in a sludge treatment reed bed between loadings

    DEFF Research Database (Denmark)

    Larsen, Julie Dam; Nielsen, Steen M; Scheutz, Charlotte

    2017-01-01

    Treatment of sludge in sludge treatment reed bed systems includes dewatering and mineralization. The mineralization process, which is driven by microorganisms, produces different gas species as by-products. The pore space composition of the gas species provides useful information on the biological...... processes occurring in the sludge residue. In this study, we measured the change in composition of gas species in the pore space at different depth levels in vertical sludge residue profiles during a resting period of 32 days. The gas composition of the pore space in the sludge residue changed during...

  14. Greenhouse gas emissions from the mineralisation process in a Sludge Treatment Reed Bed system: Seasonal variation and environmental impact

    DEFF Research Database (Denmark)

    Larsen, Julie Dam; Nielsen, Steen; Scheutz, Charlotte

    2017-01-01

    Greenhouse gas emission data from the mineralisation process in Sludge Treatment Reed Bed systems (STRB) are scarce. The aim of this study was to quantify the emission rates of carbon dioxide (CO2), methane (CH4) and nitrous oxide (N2O) and to investigate seasonal variations in order to estimate ...

  15. Reed beds may facilitate transfer of tributyltin from aquatic to terrestrial ecosystems through insect vectors in the Archipelago Sea, SW Finland.

    Science.gov (United States)

    Lilley, Thomas M; Meierjohann, Axel; Ruokolainen, Lasse; Peltonen, Jani; Vesterinen, Eero; Kronberg, Leif; Nikinmaa, Mikko

    2012-08-01

    Due to their adsorptive behavior, organotin compounds (OTCs), such as tributyltin (TBT), are accumulated in aquatic sediments. They resist biodegradation and, despite a ban in 2008, are a potential source for future exposure. Sediment OTCs have mostly been measured from sites of known high concentrations such as ports, shipping lanes, and marine dredging waste sites. The possible flow of OTCs from marine to terrestrial ecosystems, however, has not been studied. In the present study, the authors assessed whether sediments in common reed beds (Phragmites australis) accumulate TBT and whether chironomid (Diptera: Chironomidae) communities developing in reed-bed sediments act as vectors in the transfer of TBT from aquatic to terrestrial ecosystems in the Airisto channel, Archipelago Sea. The authors also investigated whether distance from the only known source and depth and TBT concentration of the adjacent shipping lane affect reed-bed concentrations. Thirty-six sites along the Airisto channel were sampled at 2-km intervals with triplicate samples from reed beds and the adjacent shipping lane for sediment and seven reed-bed sites for chironomids, and these were analyzed with an solid phase extraction liquid chromatography tamdem mass spectrometry method. The closer to the source the sample site was, the higher the measured TBT concentrations were; and the deeper the shipping lane, the lower the concentration of TBT in reed-bed sediments. The chironomid TBT concentrations correlated with reed-bed sediment TBT concentrations and showed evidence of accumulation. Therefore, TBT may be transferred, through the food web, from aquatic to terrestrial ecosystems relatively close to a source through ecosystem boundaries, such as common reed beds, which are areas of high insect biomass production in the Archipelago Sea. Copyright © 2012 SETAC.

  16. Gas composition of sludge residue profiles in a sludge treatment reed bed between loadings.

    Science.gov (United States)

    Larsen, Julie D; Nielsen, Steen M; Scheutz, Charlotte

    2017-11-01

    Treatment of sludge in sludge treatment reed bed systems includes dewatering and mineralization. The mineralization process, which is driven by microorganisms, produces different gas species as by-products. The pore space composition of the gas species provides useful information on the biological processes occurring in the sludge residue. In this study, we measured the change in composition of gas species in the pore space at different depth levels in vertical sludge residue profiles during a resting period of 32 days. The gas composition of the pore space in the sludge residue changed during the resting period. As the resting period proceeded, atmospheric air re-entered the pore space at all depth levels. The methane (CH 4 ) concentration was at its highest during the first part of the resting period, and then declined as the sludge residue became more dewatered and thereby aerated. In the pore space, the concentration of CH 4 often exceeded the concentration of carbon dioxide (CO 2 ). However, the total emission of CO 2 from the surface of the sludge residue exceeded the total emission of CH 4 , suggesting that CO 2 was mainly produced in the layer of newly applied sludge and/or that CO 2 was emitted from the sludge residue more readily compared to CH 4 .

  17. Evaluation of Green-LiDAR Data for Mapping Extent, Density and Height of Aquatic Reed Beds at Lake Chiemsee, Bavaria—Germany

    Directory of Open Access Journals (Sweden)

    Nicolás Corti Meneses

    2017-12-01

    Full Text Available Aquatic reed is an important indicator for the ecological assessment of freshwater lakes. Monitoring is essential to document its expansion or deterioration and decline. The applicability of Green-LiDAR data for the status assessment of aquatic reed beds of Bavarian freshwater lakes was investigated. The study focused on mapping diagnostic structural parameters of aquatic reed beds by exploring 3D data provided by the Green-LiDAR system. Field observations were conducted over 14 different areas of interest along 152 cross-sections. The data indicated the morphologic and phenologic traits of aquatic reed, which were used for validation purposes. For the automatic classification of aquatic reed bed spatial extent, density and height, a rule-based algorithm was developed. LiDAR data allowed for the delimitating of the aquatic reed frontline, as well as shoreline, and therefore an accurate quantification of extents (Hausdorff distance = 5.74 m and RMSE of cross-sections length 0.69 m. The overall accuracy measured for aquatic reed bed density compared to the simultaneously recorded aerial imagery was 96% with a Kappa coefficient of 0.91 and 72% (Kappa = 0.5 compared to field measurements. Digital Surface Models (DSM, calculated from point clouds, similarly showed a high level of agreement in derived heights of flat surfaces (RMSE = 0.1 m and showed an adequate agreement of aquatic reed heights with evenly distributed errors (RMSE = 0.8 m. Compared to field measurements, aerial laser scanning delivered valuable information with no disturbance of the habitat. Analysing data with our classification procedure improved the efficiency, reproducibility, and accuracy of the quantification and monitoring of aquatic reed beds.

  18. Nitrogen mineralisation and greenhouse gas emission from the soil application of sludge from reed bed mineralisation systems

    DEFF Research Database (Denmark)

    Gómez-Muñoz, B; Larsen, Julie Dam; Bekiaris, G

    2017-01-01

    A sludge treatment reed bed system (STRB) is a technology used for dewatering and stabilising sewage sludge via assisted biological mineralisation, which creates a sludge residue suitable for use as fertiliser on agricultural land. We evaluated the effect of sludge residue storage time (stabilisa......A sludge treatment reed bed system (STRB) is a technology used for dewatering and stabilising sewage sludge via assisted biological mineralisation, which creates a sludge residue suitable for use as fertiliser on agricultural land. We evaluated the effect of sludge residue storage time...... (stabilisation time) for three STRBs on soil N mineralisation and CO2 and N2O emissions in soil. The experiment revealed that the N mineralisation rate and emissions of CO2 and N2O decreased as a function of treatment time in the STRBs. Mixed sludge residue (sludge residue subjected to different treatment times......) for the three STRBs resulted in N mineralisation rates similar to the sludge residue subjected to a shorter treatment time but lower N2O emissions similar to the values of the older sludge residue. This finding reveals that combining fresh and more stabilised sludge residue ensures high N availability...

  19. Habitat selection of two Acrocephalus warblers breeding in reed beds near Malacky (Western Slovakia)

    Czech Academy of Sciences Publication Activity Database

    Prokešová, Jarmila; Kocian, Ľ.

    2004-01-01

    Roč. 59, č. 5 (2004), s. 637-644 ISSN 0006-3088 Grant - others:VEGA(SK) 1/7197/20; VEGA(SK) 1/0017/03 Institutional research plan: CEZ:AV0Z6093917 Keywords : reed warblers * breeding * habitat selection Subject RIV: EH - Ecology, Behaviour Impact factor: 0.207, year: 2004 http://biologia.savba.sk/59_5_04/Prokesova_J.pdf

  20. Life cycle assessment comparing the treatment of surplus activated sludge in a sludge treatment reed bed system with mechanical treatment on centrifuge

    DEFF Research Database (Denmark)

    Larsen, Julie Dam; Hoeve, Marieke ten; Nielsen, Steen

    2018-01-01

    or the centrifuge and terminated by land application of the final sludge product. The environmental impacts caused by the sludge treatment reed bed system strategy were comparable to or lower than those caused by the mechanical sludge treatment method. The impacts on climate change were the same for all...

  1. Operational strategy, economic and environmental performance of sludge treatment reed bed systems - based on 28 years of experience

    DEFF Research Database (Denmark)

    Nielsen, S.; Larsen, Julie Dam

    2016-01-01

    Sludge treatment reed bed (STRB) systems have been used for dewatering and mineralisation of sludge in Europe since 1988. STRB systems provide substantial environmental, economic, and operational benefits compared to mechanical sludge dewatering solutions such as belt presses and centrifuges....... They require less energy, no chemicals, reduce the sludge volume and produce bio solids with dry solid contents up to 20-40% under Danish climate conditions, depending on the sludge quality. Experience has shown that sludge treated in STRBs represents a high quality product with a low content of pathogens...... compared to conventional mechanical dewatering devices, delivering an economic break-even of about 3-5 years. This paper provides an overview of the operation and maintenance costs and environmental benefits of a typical STRB based on the experiences gained from the operation of a large number of STRBs...

  2. Septage unit treatment by sludge treatment reed beds for easy management and reuse: performance and design considerations.

    Science.gov (United States)

    Kim, Boram; Bel, Thomas; Bourdoncle, Pascal; Dimare, Jocelyne; Troesch, Stéphane; Molle, Pascal

    2018-01-01

    Sustainable treatment and management of fecal sludge in rural areas require adapted solutions. Rustic and simple operating processes such as sludge treatment reed beds (STRB) have been increasingly considered for this purpose. The biggest full scale (2,600 m 2 of STRB) septage treatment unit in France had been built in Nègrepelisse with the final objectives of reusing treated sludge and leachates for agriculture spreading and tree irrigation, respectively. The aim of this investigation was to validate the treatment chain of this installation. The obtained field data showed firstly that the overall removal efficiencies of STRB were satisfactory and stable. Removal rates higher than 98% for chemical oxygen demand and suspended solids and a 95% for Kjeldahl nitrogen represented so far a beneficial septage treatment by STRB. The highlighted necessity of a suitable complementary leachate treatment (before tree irrigation) justified the presence of the second stage of vertical flow constructed wetland. The sludge deposit drying and mineralization efficiencies were on the right track. According to hydrotextural diagram analysis, surface deposit was however found to have high deformability probably due to the youth of the installation. An in-depth understanding of STRB system needs continuous long-term studies.

  3. French Reed Bed as a Solution to Minimize the Operational and Maintenance Costs of Wastewater Treatment from a Small Settlement: An Italian Example

    Directory of Open Access Journals (Sweden)

    Anacleto Rizzo

    2018-02-01

    Full Text Available French Reed Bed (FRB is a particular constructed wetland (CW solution which receives raw wastewater. Data from the full-scale FRB wastewater treatment plant of Castelluccio di Norcia (center of Italy were collected to show the FRB capability to minimize the operational and management (O&M costs. The system was designed to treat wastewater variable from 200 person equivalent (PE in off-season up to 1000 PE. Data from 2014 up to 2016 showed high removal efficiency in line with French experiences with FRBs. An interview was conducted with the Water Utility to estimate the operational and maintenance (O&M costs faced by the WWTP, which allowed us to detail the O&M costs for energy consumption, water quality samples, and personnel for inspection. Other O&M expenditure items were estimated on the basis of parametric costs from the executive design. The FRB O&M costs in euro for 500–1000 PE (6–11 € PE−1 year−1 resulted from 5 to 13 lower in comparison to those reported for classical activated sludge systems in an Italian context (45–90 € year−1. The low O&M costs are mainly due to the limited energy consumed and to the minimized costs of sludge management.

  4. Performance of a system with full- and pilot-scale sludge drying reed bed units treating septic tank sludge in Brazil.

    Science.gov (United States)

    Calderón-Vallejo, Luisa Fernanda; Andrade, Cynthia Franco; Manjate, Elias Sete; Madera-Parra, Carlos Arturo; von Sperling, Marcos

    2015-01-01

    This study investigated the performance of sludge drying reed beds (SDRB) at full- and pilot-scale treating sludge from septic tanks in the city of Belo Horizonte, Brazil. The treatment units, planted with Cynodon spp., were based on an adaptation of the first-stage of the French vertical-flow constructed wetland, originally developed for treating sewage. Two different operational phases were investigated; in the first one, the full-scale unit was used together with six pilot-scale columns in order to test different feeding strategies. For the second phase, only the full-scale unit was used, including a recirculation of the filtered effluent (percolate) to one of the units of the French vertical wetland. Sludge application was done once a week emptying a full truck, during 25 weeks. The sludge was predominantly diluted, leading to low solids loading rates (median values of 18 kgTS m(-2) year(-1)). Chemical oxygen demand removal efficiency in the full-scale unit was reasonable (median of 71%), but the total solids removal was only moderate (median of 44%) in the full-scale unit without recirculation. Recirculation did not bring substantial improvements in the overall performance. The other loading conditions implemented in the pilot columns also did not show statistically different performances.

  5. Statistical optimization of the phytoremediation of arsenic by Ludwigia octovalvis- in a pilot reed bed using response surface methodology (RSM) versus an artificial neural network (ANN).

    Science.gov (United States)

    Titah, Harmin Sulistiyaning; Halmi, Mohd Izuan Effendi Bin; Abdullah, Siti Rozaimah Sheikh; Hasan, Hassimi Abu; Idris, Mushrifah; Anuar, Nurina

    2018-06-07

    In this study, the removal of arsenic (As) by plant, Ludwigia octovalvis, in a pilot reed bed was optimized. A Box-Behnken design was employed including a comparative analysis of both Response Surface Methodology (RSM) and an Artificial Neural Network (ANN) for the prediction of maximum arsenic removal. The predicted optimum condition using the desirability function of both models was 39 mg kg -1 for the arsenic concentration in soil, an elapsed time of 42 days (the sampling day) and an aeration rate of 0.22 L/min, with the predicted values of arsenic removal by RSM and ANN being 72.6% and 71.4%, respectively. The validation of the predicted optimum point showed an actual arsenic removal of 70.6%. This was achieved with the deviation between the validation value and the predicted values being within 3.49% (RSM) and 1.87% (ANN). The performance evaluation of the RSM and ANN models showed that ANN performs better than RSM with a higher R 2 (0.97) close to 1.0 and very small Average Absolute Deviation (AAD) (0.02) and Root Mean Square Error (RMSE) (0.004) values close to zero. Both models were appropriate for the optimization of arsenic removal with ANN demonstrating significantly higher predictive and fitting ability than RSM.

  6. Method of burning sulfur-containing fuels in a fluidized bed boiler

    Science.gov (United States)

    Jones, Brian C.

    1982-01-01

    A method of burning a sulfur-containing fuel in a fluidized bed of sulfur oxide sorbent wherein the overall utilization of sulfur oxide sorbent is increased by comminuting the bed drain solids to a smaller average particle size, preferably on the order of 50 microns, and reinjecting the comminuted bed drain solids into the bed. In comminuting the bed drain solids, particles of spent sulfur sorbent contained therein are fractured thereby exposing unreacted sorbent surface. Upon reinjecting the comminuted bed drain solids into the bed, the newly-exposed unreacted sorbent surface is available for sulfur oxide sorption, thereby increasing overall sorbent utilization.

  7. Hydrogen sulfide release from dairy manure storages containing gypsum bedding

    Science.gov (United States)

    Recycled gypsum products can provide a cost-effective bedding alternative for dairy producers. Manufacturers report reduced odors, moisture and bacteria in the stall environment when compared to traditional bedding. Gypsum provides a sulfate source that can be converted to hydrogen sulfide under ana...

  8. Inoculation of fumigated nursery beds and containers with arbuscular mycorrhizal products for eastern redcedar production

    Science.gov (United States)

    Michelle M. Cram; Stephen W. Fraedrich

    2015-01-01

    Commercially available arbuscular mycorrhizal (AM) products were applied at an operational rate to eastern redcedar (Juniperus virginiana L.) nursery beds and containers to evaluate seedling growth and colonization responses. A field study at the Augusta Forestry Center in Crimora, VA, and a companion container study were initiated in the fall of 2012. MycoApply® Endo...

  9. Lignite air-steam gasification in the fluidized bed of iron-containing slag catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Kuznetsov, B.N.; Shchipko, M.L.; Golovin, Yu. [Inst. of Chemistry of Natural Organic Materials, Academgorodok, Krasnoyarsk (Russian Federation)

    1995-12-01

    The influence of fluidized bed of iron-containing slag particles on air-steam gasification of powdered Kansk-Achinsk lignite in entrained flow was studied in pilot installation with productivity about 60 kg per hour. Slag of Martin process and boiler slag were used as catalytic active materials until their complete mechanical attrition. Two following methods of catalytic gasification of lignite were compared: the partial gasification in stationary fluidized bed of slag particles with degree of fuel conversion 40-70% and complete gasification in circulating bed of slag particles. In the first case only the most reactive part of fuel is gasified with the simultaneously formation of porous carbon residue with good sorption ability. It was found the catalytic fluidized bed improves heat transfer from combustion to reduction zone of gas-generator and increases the rate of fuel conversion at the temperature range 900-1000{degrees}C. At these temperatures the degree of conversion is depended considerably on the duration time of fuel particles in the catalytic fluidized bed. The influence of catalytic fluidized bed height and velocity of reaction mixture on the temperature profiles in the gas-generator was studied. The optimal relationship was found between the fluidized bed height and velocity of flow which makes possible to produce the gas with higher calorific value at maximum degree of fuel conversion.

  10. Hydrodynamic calculation of a filter sand bed type used in the containment venting systems

    International Nuclear Information System (INIS)

    Cuevas V, D.; Sainz M, E.; Ortiz V, J.

    2015-09-01

    The filtered venting of the containment has been adopted in European countries to mitigate the consequences of excess pressure containment during a severe accident. When venting has taken place, the fission products are released directly into the environment, unless a filter on the same path is placed, so that various types of filters are used to trap the fission products. The venting filters of the containment currently installed use different filtration technologies that involve more than one medium. Those using water as the first stage of filtration are called wet systems and are equipped with additional steps to remove water drops and fine aerosols emissions. And even they may also be equipped with an element containing certain absorption means for the filtration of gaseous iodine species. Other designs based on filtration of deep bed as the primary retention step; called dry filters, use filtration media of metal fiber, ceramic or sand to trap aerosols. This paper evaluates the hydraulic characteristics of the filter sand bed type designed by EDF as a candidate to be installed in the containment of BWR Mark II (type of primary containment of the nuclear power plant of Laguna Verde). The evaluation of filter sand bed type was performed using the software package of open source OpenFOAM. Models of each zone of the filtered device were generated and through a series of parametric calculations of computational fluid mechanics relevant hydrodynamic characteristics of the device were obtained, such as pressure drops against mass flow rate and pressure fields and speed at different operating conditions. On the other hand, the model validation of the sand bed filter when comparing the results of experimental tests on a sand column of PITEAS program (1985-1986) against OpenFOAM simulation was realized. The results are very close to those obtained experimentally. (Author)

  11. Packed bed reactor for degradation of simulated cyanide-containing wastewater

    OpenAIRE

    Kumar, Virender; Kumar, Vijay; Bhalla, Tek Chand

    2014-01-01

    The discharge of cyanide-containing effluents into the environment contaminates water bodies and soil. Effective methods of treatment which can detoxify cyanide are the need of the hour. The aim of the present study is to develop a bioreactor for complete degradation of cyanide using immobilized cells of Serratia marcescens RL2b. Alginate-entrapped cells of S. marcescens RL2b were used for complete degradation of cyanide in a packed bed reactor (PBR). Cells grown in minimal salt medium (pH 6....

  12. Generic Reed Solomon Encorder

    Directory of Open Access Journals (Sweden)

    Petrus Mursanto

    2006-11-01

    Full Text Available Reed Solomon (RS codes is a mechanism to detect and correct burst of errors in data transmission and storage systems. It provides a solid introduction to foundation mathematical concept of Galois Field algebra and its application. With the development of digital hardware technology, the RS concepts were brought into reality, i.e. the implementation of RS codec chips. This paper presents the development steps of a generic RS encoder using VHDL. The encoder is able to handle generic width of data, variable length of information, number of error as well as variable form of primitive polynomial and generator polynomial used in the system. The design has been implemented for FPGA chip Xilinx XC3S200-5FT256 and has a better performance than commercially available equivalent encoder.

  13. Saving reed lands by giving economic value to reed

    Directory of Open Access Journals (Sweden)

    F.W. Croon

    2014-07-01

    Full Text Available Discussions about the need for renewable energy, the need for nature conservation, the need to double the world’s food production to eliminate hunger, the need to reduce carbon dioxide emission, and the wish to reduce dependency on dwindling oil resources, show that these issues are intimately related and sometimes mutually exclusive. The use of food crops for the production of renewable fuels has resulted in the energy vs. food debate; the use of scarce land and fresh water for the dedicated production of biomass conflicts with food production and nature conservation; the collection of harvest residues and forest wastes as biomass to produce renewable fuels is complex and leaves a CO2 footprint. The several species of reed that grow naturally in deltas, river plains etc. can provide large amounts of biomass but are hardly mentioned in the debates. Harvesting reed does not threaten the nature and the natural functions of reed lands, which are carbon neutral or carbon dioxide sinks. Reed production does not need extensive infrastructure or complex cultivation and does not compete with food production for land and fresh water. Reed lands in many places are under threat of reclamation for economic activities and urbanisation. This trend can be countered if reed is seen to have a proven economic value. In this article I argue that giving a sustainable economic value to reed lands can only be realised if the exploitation is recognised as being environmentally acceptable, commercially feasible and a source of economic gains for all stakeholders. Commercial feasibility can be achieved under present economic conditions only if a reliable supply of considerable volumes of reed at a limited price can be guaranteed.

  14. Quench cooling of superheated debris beds in containment during LWR core meltdown accidents

    International Nuclear Information System (INIS)

    Ginsberg, T.; Chen, J.C.

    1984-01-01

    Light water reactor core meltdown accident sequence studies suggest that superheated debris beds may settle on the concrete floor beneath the reactor vessel. A model for the heat transfer processes during quench of superheated debris beds cooled by an overlying pool of water has been presented in a prior paper. This paper discusses the coolability of decay-heated debris beds from the standpoint of their transient quench characteristics. It is shown that even though a debris bed configuration may be coolable from the point of view of steady-state decay heat removal, the quench behavior from an initially elevated temperature may lead to bed melting prior to quench of the debris

  15. Treatment of Ni-EDTA containing wastewater by electrocoagulation using iron scraps packed-bed anode.

    Science.gov (United States)

    Ye, Xiaokun; Zhang, Junya; Zhang, Yan; Lv, Yuancai; Dou, Rongni; Wen, Shulong; Li, Lianghao; Chen, Yuancai; Hu, YongYou

    2016-12-01

    The unique electrocoagulator proposed in this study is highly efficient at removing Ni-EDTA, providing a potential remediation option for wastewater containing lower concentrations of Ni-EDTA (Ni ≤ 10 mg L -1 ). In the electrocoagulation (EC) system, cylindrical graphite was used as a cathode, and a packed-bed formed from iron scraps was used as an anode. The results showed that the removal of Ni-EDTA increased with the application of current and favoured acidic conditions. We also found that the iron scrap packed-bed anode was superior in its treatment ability and specific energy consumption (SECS) compared with the iron rod anode. In addition, the packed density and temperature had a large influence on the energy consumption (ECS). Over 94.3% of Ni and 95.8% of TOC were removed when conducting the EC treatment at an applied current of 0.5 A, initial pH of 3, air-purged rate 0.2 L min -1 , anode packed density of 400 kg m -3 temperature of 313 K and time of 30 min. SEM analysis of the iron scraps indicated that the specific area of the anode increased after the EC. The XRD analysis of flocs produced during EC revealed that hematite (α-Fe 2 O 3 ) and magnetite (Fe 3 O 4 ) were the main by-products under aerobic and anoxic conditions, respectively. A kinetic study demonstrated that the removal of Ni-EDTA followed a first-order model with the current parameters. Moreover, the removal efficiency of real wastewater was essentially consistent with that of synthetic wastewater. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. Quench cooling of superheated debris beds in containment during LWR core meltdown accidents

    International Nuclear Information System (INIS)

    Ginsberg, T.; Chen, J.C.

    1984-01-01

    Light water reactor core meltdown accident sequence studies suggest that superheated debris beds may settle on the concrete floor beneath the reactor vessel. A model for the heat transfer processes during quench (removal of stored energy from initial temperature to saturation temperature) of superheated debris beds cooled by an overlying pool of water has been presented in a prior paper. This paper discusses the coolability of decay-heated debris beds from the standpoint of their transient quench characteristics. It is shown that even though a debris bed configuration may be coolable from the point of view of steady-state decay heat removal, the quench behavior from an initially elevated temperature may lead to bed melting prior to quench of the debris

  17. Packed bed reactor for degradation of simulated cyanide-containing wastewater.

    Science.gov (United States)

    Kumar, Virender; Kumar, Vijay; Bhalla, Tek Chand

    2015-10-01

    The discharge of cyanide-containing effluents into the environment contaminates water bodies and soil. Effective methods of treatment which can detoxify cyanide are the need of the hour. The aim of the present study is to develop a bioreactor for complete degradation of cyanide using immobilized cells of Serratia marcescens RL2b. Alginate-entrapped cells of S. marcescens RL2b were used for complete degradation of cyanide in a packed bed reactor (PBR). Cells grown in minimal salt medium (pH 6.0) were harvested after 20 h and exhibited 0.4 U mg -1  dcw activity and 99 % cyanide degradation in 10 h. These resting cells were entrapped using 3 % alginate beads and packed in a column reactor (20 × 1.7 cm). Simulated cyanide (12 mmol l -1 )-containing wastewater was loaded and fractions were collected after different time intervals at various flow rates. Complete degradation of 12 m mmol l -1 (780 mg l -1 ) cyanide in 10 h was observed at a flow rate of 1.5 ml h -1 . The degradation of cyanide in PBR showed direct dependence on retention time. The retention time of cyanide in the reactor was 9.27 h. The PBR can degrade 1.2 g of cyanide completely in 1 day.

  18. Rotation Impact of Reed Switch

    International Nuclear Information System (INIS)

    Park, Yun Bum; Lee, Jae Seon; Kim, Jong Wook; Han, Eun Sil; Park, Hee June

    2016-01-01

    A CRDM (Control Rod Drive Mechanism) is an electromagnetic device which drives a control rod assembly linearly to regulate the reactivity of a nuclear core. A RPIS (Rod Position Indication System) is used as a position indicator of a control rod assembly for a CRDM of a nuclear reactor, SMART. A highly accurate RPIS for SMART is required because the reactivity of a nuclear core for a small modular reactor is more sensitive than the commercial ones. In this study, the effect of positioning direction of the reeds in a reed switch for the CRDM RPIS has been studied using the electromagnetic FE analysis. It is found that the positioning direction of the reeds slightly but not significantly affects the formation of attraction. Analysis results will be used as the basis on estimated accuracy of full RPIS system.

  19. Rotation Impact of Reed Switch

    Energy Technology Data Exchange (ETDEWEB)

    Park, Yun Bum; Lee, Jae Seon; Kim, Jong Wook [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Han, Eun Sil [Taesung S and E, Seoul (Korea, Republic of); Park, Hee June [Woojin Inc., Hwaseong (Korea, Republic of)

    2016-10-15

    A CRDM (Control Rod Drive Mechanism) is an electromagnetic device which drives a control rod assembly linearly to regulate the reactivity of a nuclear core. A RPIS (Rod Position Indication System) is used as a position indicator of a control rod assembly for a CRDM of a nuclear reactor, SMART. A highly accurate RPIS for SMART is required because the reactivity of a nuclear core for a small modular reactor is more sensitive than the commercial ones. In this study, the effect of positioning direction of the reeds in a reed switch for the CRDM RPIS has been studied using the electromagnetic FE analysis. It is found that the positioning direction of the reeds slightly but not significantly affects the formation of attraction. Analysis results will be used as the basis on estimated accuracy of full RPIS system.

  20. Fast Reed-Solomon Decoder

    Science.gov (United States)

    Liu, K. Y.

    1986-01-01

    High-speed decoder intended for use with Reed-Solomon (RS) codes of long code length and high error-correcting capability. Design based on algorithm that includes high-radix Fermat transform procedure, which is most efficient for high speeds. RS code in question has code-word length of 256 symbols, of which 224 are information symbols and 32 are redundant.

  1. Biologically effective dose (BED) for interstitial seed implants containing a mixture of radionuclides with different half-lives

    International Nuclear Information System (INIS)

    Chen Zhe; Nath, Ravinder

    2003-01-01

    Purpose: To develop a tool for evaluating interstitial seed implants that contain a mixture of radionuclides with different half-lives and to demonstrate its utility by examining the clinical implications of prescribing to an isodose surface for such an implant. Methods and Materials: A linear-quadratic model for continuous low dose rate irradiation was developed for permanent implants containing a mixture of radionuclides. Using a generalized equation for the biologically effective dose (BED), the effects of cell proliferation and sublethal damage repair were examined systematically for implants containing a mixture of radionuclides. A head-and-neck permanent seed implant that contained a mixture of 125 I and 103 Pd seeds was used to demonstrate the utility of the generalized BED. Results: An equation of BED for implants containing a mixture of radionuclides with different half-lives was obtained. In such an implant, the effective cell kill was shown to depend strongly on the relative dose contributions from each radionuclide type; dose delivered by radionuclides with shorter half-life always resulted in more cell kill for any given sublethal damage repair and cell proliferation rates. Application of the BED formula to an implant containing a mixture of 125 I and 103 Pd seeds demonstrates that the conventional dose prescription to an isodose surface is not unique for such an implant. When the prescription dose was based on existing clinical experience of using 125 I seeds alone, mixing 103 Pd seeds with 125 I seeds would increase the cell kill. On the other hand, if the prescription dose were based on existing clinical experience of using 103 Pd seeds alone, mixing 125 I seeds with 103 Pd seeds in the same implant would create radiobiologically 'cold' spots (i.e., an increase in cell survival) at locations where a major portion of the prescription dose is contributed by the 125 I seeds. For fast-growing tumors, these 'cold' spots can become significant

  2. Distribution of volatile sulphur containing products during fixed bed pyrolysis and gasification of coals

    Energy Technology Data Exchange (ETDEWEB)

    Furimsky, E.

    1991-08-01

    Various coals were used to study the evolution of H{sub 2}S COS, and SO{sub 2} in a fixed bed reactor. For all types of coal, most of H{sub 2}S and SO{sub 2} were released during the devolatilization stage. COS was formed only during the gasification stage in the presence of CO{sub 2}.

  3. Assemblage of filamentous fungi associated with aculeate hymenopteran brood in reed galls.

    Science.gov (United States)

    Heneberg, Petr; Bizos, Jiří; Čmoková, Adéla; Kolařík, Miroslav; Astapenková, Alena; Bogusch, Petr

    2016-01-01

    Monotypic stands of common reed and the reed-gall-associated insect assemblages are distributed worldwide. However, fungi associated with these assemblages have not been characterized in detail. Here we examined 5200 individuals (12 species) of immature aculeate hymenopterans or their parasitoids collected at 34 sampling sites in Central Europe. We noticed fungal outgrowth on exoskeletons of 83 (1.60%) larvae and pupae. The most common host was eudominant Pemphredon fabricii. However, the less abundant aculeate hymenopteran reed gall inquilines were infected at higher prevalence, these included Trypoxylon deceptorium, Trypoxylon minus, Hoplitis leucomelana and Hylaeus moricei (all considered new host records). We identified three fungal species, Penicillium buchwaldii (72% of cases), Aspergillus pseudoglaucus (22%) and Penicillium quebecense (6%). When multibrooded nests were affected, only a part of individuals was infected in 62% of cases. The sampling site-specific infection rate reached up to 13%, thus fungal infections should be considered an important variable driving the abundance of gall inquilines. Infections of generalist host species were more frequent than those of reed gall specialists, suggesting that suboptimal conditions decreased the immunocompetence of non-specialized species, which only occasionally nest in reed galls and feed in reed beds. Copyright © 2015 Elsevier Inc. All rights reserved.

  4. Detection of Reduced Susceptibility to Chlorfenapyr- and Bifenthrin-Containing Products in Field Populations of the Bed Bug (Hemiptera: Cimicidae).

    Science.gov (United States)

    Ashbrook, Aaron R; Scharf, Michael E; Bennett, Gary W; Gondhalekar, Ameya D

    2017-06-01

    Insecticide resistance is a major impediment for effective control of Cimex lectularius L. Previous resistance detection studies with bed bugs have focused on certain pyrethroid, neonicotinoid, organochlorine, organophosphate, and carbamate insecticides. Within the pyrethroid class, resistance studies have mostly been limited to deltamethrin, lambda-cyhalothrin, and alpha- and beta-cyfluthrin. The goal of this study was to develop diagnostic concentration bioassays for assessing bed bug susceptibility levels to chlorfenapyr- and bifenthrin-containing products. First, glass vial and filter paper bioassay methods were compared for their utility in susceptibility monitoring. Statistical comparison of toxicity data between bioassays indicated that the vial assay was less confounded by assay susbtrate effects, required less insecticide, and was faster, especially for chlorfenapyr. Next, using vial diagnostic concentrations (LC99) for each insecticide, 10 laboratory-adapted field strains and the Harlan lab-susceptible strain were screened for susceptibility to chlorfenapyr and bifenthrin. The results of this study reveal recent bed bug susceptibility levels to certain chlorfenapyr- and bifenthrin-containing products. Reduced susceptibility was detected in three and five field strains to chlorfenapyr and bifenthrin, respectively. Detection of reduced susceptibility suggests that certain strains may be segregating toward greater chlorfenapyr and bifenthrin resistance. These results merit continuous resistance monitoring efforts to detect chlorfenapyr and bifenthrin susceptibility shifts. Additionally, to reduce insecticide selection pressures and delay resistance development, adoption of integrated bed bug control strategies that combine chemical and nonchemical methods is recommended. © The Authors 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  5. Reeds diesel engine troubleshooting handbook

    CERN Document Server

    Pickthall, Barry

    2013-01-01

    Most diesel engines will develop a problem at some point in their lives, but armed with the right knowledge a skipper needn't worry. The Reeds Diesel Engine Troubleshooting Handbook is a compact, pocket-sized guide to finding solutions to all of the most common engine problems, and many of the less common ones too. The perfect format for quick reference on board, this book will help skippers fix troublesome engines themselves, avoiding costly engineer fees if the problem is simple to sort out, or enabling an emergency patch-up for a more serious problem until they can get back to port. Each to

  6. Effects of resource activities upon repository siting and waste containment with reference to bedded salt

    International Nuclear Information System (INIS)

    Ashby, J.; Rowe, J.

    1980-02-01

    The primary consideration for the suitability of a nuclear waste repository site is the overall ability of the repository to safely contain radioactive waste. This report is a discussion of the past, present, and future effects of resource activities on waste containment. Past and present resource activities which provide release pathways (i.e., leaky boreholes, adjacent mines) will receive initial evaluation during the early stages of any repository site study. However, other resource activities which may have subtle effects on containment (e.g., long-term pumping causing increased groundwater gradients, invasion of saline water causing lower retardation) and all potential future resource activities must also be considered during the site evaluation process. Resource activities will affect both the siting and the designing of repositories. Ideally, sites should be located in areas of low resource activity and low potential for future activity, and repository design should seek to eliminate or minimize the adverse effects of any resource activity. Buffer zones should be created to provide areas in which resource activities that might adversely affect containment can be restricted or curtailed. This could mean removing large areas of land from resource development. The impact of these frozen assets should be assessed in terms of their economic value and of their effect upon resource reserves. This step could require a major effort in data acquisition and analysis followed by extensive numerical modeling of regional fluid flow and mass transport. Numerical models should be used to assess the effects of resource activity upon containment and should include the cumulative effects of different resource activities. Analysis by other methods is probably not possible except for relatively simple cases

  7. Conceptual design of retrieval systems for emplaced transuranic waste containers in a salt bed depository. Final report

    International Nuclear Information System (INIS)

    Fogleman, S.F.

    1980-04-01

    The US Department of Energy and the Nuclear Regulatory Commission have jurisdiction over the nuclear waste management program. Design studies were previously made of proposed repository site configurations for the receiving, processing, and storage of nuclear wastes. However, these studies did not provide operational designs that were suitable for highly reliable TRU retrieval in the deep geologic salt environment for the required 60-year period. The purpose of this report is to develop a conceptual design of a baseline retrieval system for emplaced transuranic waste containers in a salt bed depository. The conceptual design is to serve as a working model for the analysis of the performance available from the current state-of-the-art equipment and systems. Suggested regulations would be based upon the results of the performance analyses

  8. Double-reed exhaust valve engine

    Science.gov (United States)

    Bennett, Charles L.

    2015-06-30

    An engine based on a reciprocating piston engine that extracts work from pressurized working fluid. The engine includes a double reed outlet valve for controlling the flow of low-pressure working fluid out of the engine. The double reed provides a stronger force resisting closure of the outlet valve than the force tending to open the outlet valve. The double reed valve enables engine operation at relatively higher torque and lower efficiency at low speed, with lower torque, but higher efficiency at high speed.

  9. Biodiversity of Van Reeds, Eastern Turkey

    Directory of Open Access Journals (Sweden)

    Özdemir Adızel

    2017-12-01

    Full Text Available In this study, it is aimed to determine the vertebrate fauna and flora species diversity of Van Reeds. For this purpose, studies were conducted between 2014 and 2017 and 1 fish, 3 frog, 6 reptilian, 185 bird, and 5 mammal species, 200 fauna species and 79 flora species in total, were determined in the study area. Van Reeds is an important breeding, feeding, and wintering feature especially for birds. Reeds, which has various biodiversity, is exposed to intense pressure and destruction. The main threats in the study area are construction, filling, hunting, drainage, and pollution.

  10. The conditions for use of reed canary grass briquettes and chopped reed canary grass in small heating plants; Foerutsaettningar foer anvaendning av roerflensbriketter och hackad roerflen i mindre vaermecentraler

    Energy Technology Data Exchange (ETDEWEB)

    Paulrud, Susanne; Davidsson, Kent; Holmgren, Magnus A. (Swedish National Testing and Research Inst., Boraas (Sweden)); Hedman, Henry; Oehman, Rikard; Leffler, Joel (ETC, Piteaa (Sweden))

    2010-09-15

    The aim of this study was to test fuel blends of briquettes and chopped reed canary grass in three existing heating plants (50 kW - 500 kW) and elucidate the requirements for good performance and low emissions. In addition, the study investigated production of reed canary grass briquettes using a Polish screw press developed for straw. Some tests with a bale shredder were also undertaken. The screw press technique is of interest for reed canary grass because it is a simple technique, easy to handle, developed for small scale production, and for straw. The test with reed canary grass in this study showed that the technique worked well but that further adjustments and a longer test period are needed in order to achieve higher bulk density and mechanical strength. The test with chopped reed canary grass shows that a system with a forage harvester is slightly more effective than baling and cutting in a bale shredder. The study concluded that few existing heating plants of size 50 kW-1 MW that currently use wood fuels will be able to use reed canary grass without adjustment, conversion or replacement of the combustion equipment. Reed canary grass has 15-20 times higher ash content than wood briquettes and 2-3 times higher ash content than forest residue; the combustion equipment must be able to handle these properties. The boiler must be equipped with a continuously operating ashing system and it must be possible to move the ash bed mechanically. There is a risk of high content of unburned matter if the residence time in the boiler is too short, due to the structure and low bulk density of the reed canary grass ash. Using a blend of wood briquettes and reed canary briquettes results in lower ash content, but also affects the ash chemistry and tends to lower the initial ash fusion temperature compared to using 100 % reed canary grass. Blending chopped reed canary grass and wood chips in an existing small scale heating plant also requires measures to achieve an even fuel

  11. An overview of the Central Queensland University self-contained evapotranspiration beds.

    Science.gov (United States)

    Kele, B; Midmore, D J; Harrower, K; McKennariey, B J; Hood, B

    2005-01-01

    The Central Queensland University (CQU) has championed a self-contained concrete lined evapotranspiration channel. Any non-transpired effluent returns to a holding tank and is recirculated through the evapotranspiration channel until it is used. This paper examines the results from the Rockhampton trial site. Nutrient ions in the effluent were quantified over time and found not to accumulate in solution. Microbial analysis of the treated effluent was performed and was found to be within the ranges required by the relevant legislative codes. Citrus fruit grown in the evapotranspiration channel were sampled and no elevated levels of faecal coliforms were recorded. Macronutrients and micronutrients of the soil in the channels were measured over a 5-year period. No toxic accumulations or nutrient deficiencies in the soil occurred. Levels of salinity and sodicity in the evapotranspiration channel soil were quantified. Salinity rose slightly, as did sodium. Concentrations of salts and sodium did not reach unsustainable levels. The aim of the trial was to develop an on-site treatment and reuse system that is sustainable and protects public and environmental health.

  12. Position indicating systems and reed contact unit assemblies for such systems

    International Nuclear Information System (INIS)

    Foxworthy, M.K.

    1980-01-01

    Specifications are given for a position indicating system for determining the position of a movable member inside a sealed container such as the position of a control rod in a nuclear reactor. The system comprises a magnetic flux producing member mounted to the movable member so as to move with it, a series of magnetic reed contact units mounted along the outside of the sealed container to be individually actuated by the flux producer as the movable member moves within the sealed container to indicate the position of this member. Each of the reed contact units is connected to a source of alternating electric current to produce a magnetic flux field to minimize the flux differential between the actuated and unactuated reed contact positions. A second aspect of the invention provides for a low operating flux differential reed contact unit assembly for a position indicating system such that it is actuated by the magnetic member at one magnetic flux level and deactivated at a second level. There is a source of alternating current connected to a coil surrounding the reed contact unit so as to produce an alternating magnetic flux with amplitude less than the difference between the two levels. Variations are given, also diagrams and benefits. (U.K.)

  13. Ecology and physiology of reed. A literature study for evaluation of reed as an energy source

    Energy Technology Data Exchange (ETDEWEB)

    Bjoerndahl, G.; Egneus, H.

    1980-04-01

    The potentials of reed as an energy source are evaluated. The following subjects are discussed: The structure and life-cycle of reed; Primary production and photosynthesis; important environmental factors for the production; Genetic variation; Competition, succession and parasitism; Human influence like cultivation, harvesting a.o. An extensive list of referencer is given.

  14. Bioaccumulation of metals in reeds collected from an acid mine drainage contaminated site in winter and spring.

    Science.gov (United States)

    Guo, Lin; Cutright, Teresa J

    2016-01-01

    Wetland plants such as Phragmites australis has been used to treat acid mine drainage (AMD) contaminated soil which is a serious environmental issue worldwide. This project investigated metal plaque content(s) and metal uptake in reeds grown in an AMD field in winter and spring. The results indicated that the level of Fe plaque was much higher than Mn and Al plaque as the soil contained more Fe than Al and Mn. The amounts of Mn and Al plaque formed on reeds in spring were not significantly different from that in winter (p > .05). However, more Fe plaque was formed on reeds collected in spring. The concentrations of metals in underground organs were positively related to the metal levels in soils. More Mn and Al transferred to the aboveground tissues of reeds during the spring while the Fe levels in reeds did not significantly vary with seasons. Roots and rhizomes were the main organs for Fe sequestration (16.3 ± 4.15 mg/g in roots in spring) while most Al was sequestered in the shoots of reeds (2.05 ± 0.09 mg/g in shoots in spring). Further research may be needed to enhance the translocation of metals in reeds and increase the phytoremediation efficiency.

  15. Treatment of petroleum refinery wastewater containing heavily polluting substances in an aerobic submerged fixed-bed reactor.

    Science.gov (United States)

    Vendramel, S; Bassin, J P; Dezotti, M; Sant'Anna, G L

    2015-01-01

    Petroleum refineries produce large amount of wastewaters, which often contain a wide range of different compounds. Some of these constituents may be recalcitrant and therefore difficult to be treated biologically. This study evaluated the capability of an aerobic submerged fixed-bed reactor (ASFBR) containing a corrugated PVC support material for biofilm attachment to treat a complex and high-strength organic wastewater coming from a petroleum refinery. The reactor operation was divided into five experimental runs which lasted more than 250 days. During the reactor operation, the applied volumetric organic load was varied within the range of 0.5-2.4 kgCOD.m(-3).d(-1). Despite the inherent fluctuations on the characteristics of the complex wastewater and the slight decrease in the reactor performance when the influent organic load was increased, the ASFBR showed good stability and allowed to reach chemical oxygen demand, dissolved organic carbon and total suspended solids removals up to 91%, 90% and 92%, respectively. Appreciable ammonium removal was obtained (around 90%). Some challenging aspects of reactor operation such as biofilm quantification and important biofilm constituents (e.g. polysaccharides (PS) and proteins (PT)) were also addressed in this work. Average PS/volatile attached solids (VAS) and PT/VAS ratios were around 6% and 50%, respectively. The support material promoted biofilm attachment without appreciable loss of solids and allowed long-term operation without clogging. Microscopic observations of the microbial community revealed great diversity of higher organisms, such as protozoa and rotifers, suggesting that toxic compounds found in the wastewater were possibly removed in the biofilm.

  16. Reed Canary Grass Project. Development of a new crop production system based on delayed harvesting and a system for its combined processing to chemical pulp and bio fuel powder

    Energy Technology Data Exchange (ETDEWEB)

    Olsson, Rolf (ed.) (and others)

    2004-07-01

    . In this process will the silica problem in the chemical recovery process also be reduced. For integrating a grass cooking line in existing pulp and paper mills also the sulphate cooking process, have been developed for use with reed canary grass. Pulp produced from fractionated reed canary grass can easily be bleached to full brightness of 90 % ISO with environmentally friendly bleaching processes and technically well documented chemical recovery systems can be used. Reed canary grass contains relatively short fibres which can replace hardwood fibres in high quality printing papers. The pulp produced was evaluated for end use as board (white-top liner) and fine paper. The mill produced reed canary grass pulp had better optical properties and bulk than pulp produced in laboratory although it was not possible to optimise all parameters during the short time the mill was available for the trial. The white top liner tests with mill produced pulp showed that the excellent good light scattering make it possible to produce board with equal quality using less fibre compared to what is needed using birch pulp. Reed canary grass pulp is thus a promising new fibre for board production. The mill produced pulp had also equal or better quality than pulp from birch and disc mill processed reed canary grass pulp can also compete with Eucalyptus pulp. The intermediate processed fuel raw material showed good possibilities to be processed to upgraded biofuels as powder, briquettes and pellets although more research have to be done concerning technology development. Using additives helps to form good quality pellets. Sugar molasses helped to make better quality pellets using less energy. But this is of course extra cost in pellet making. Optimisation of RCG meal fraction pelletising needs more tests, but with these pilot tests it was shown that RCG meal fraction can be pelletised also without any additives and good quality pellets can be formed. Reed canary grass pellets have a high ash

  17. Theoretical and experimental investigation on adaptability of charcoal beds to containment filter venting in Italian nuclear power plant

    International Nuclear Information System (INIS)

    Caropreso, G.; Leonardi, A.; Perna, W.; Sgalambro, G.

    1989-01-01

    The work has been divided into three parts. The first one gives a description of the facilities under investigation during some selected accidental conditions, also described. The second part, which consists of an experimental work, tries to identify the behavior of charcoal beds in terms of pressure drop vs the aerosol mass loading and of aerosol retention efficiency. On the basis of the experimental findings, the prediction of the behavior of the real beds is carried out in the third part, as regards the pressure drop through the beds, related to the selected accident scenarios. In addition in this last part the results of a preliminary evaluation of the maximum decay power picked up by the beds without reaching the carbon self-ignition temperature have been reported

  18. Simulation of Single Reed Instruments Oscillations Based on Modal Decomposition of Bore and Reed Dynamics

    OpenAIRE

    Silva, Fabrice; Debut, Vincent; Kergomard, Jean; Vergez, Christophe; Deblevid, Aude; Guillemain, Philippe

    2007-01-01

    This paper investigates the sound production in a system made of a bore coupled with a reed valve. Extending previous work (Debut, 2004), the input impedance of the bore is projected on the modes of the air column. The acoustic pressure is therefore calculated as the sum of modal components. The airrrflow blown into the bore is modulated by reed motion, assuming the reed to be a single degree of freedom oscillator. Calculation of self-sustained oscillations controlled by time-varyi...

  19. Reeds as potential sources of alcohol

    Energy Technology Data Exchange (ETDEWEB)

    Lodh, A B; Rao, P R

    1964-01-01

    Five species of reeds, Erianthus ravennae, Saccharum munja S. procerum, Phragmites communis, and Neyraudia reynaudiana yielded 25.02, 19.5, 24.11, 26.1, and 21.6% reducing sugars, repectively., when digested with 1% H/sub 2/SO/sub 4/ under 15lb/square inch for 3 hours. Fermentable sugars from hydrolyzates of the above reeds were 70.0, 34.5, 65.0, 28.0, and 67.5% respectively. This source can become important only in case of an acute demand for fermentation alcohol.

  20. Quality indicators for woodwind reed material

    International Nuclear Information System (INIS)

    Glave, Stefan; Pallon, Jan; Bornman, Chris; Bjoern, Lars Olof; Wallen, Rita; Raastam, Jacob; Kristiansson, Per; Elfman, Mikael; Malmqvist, Klas

    1999-01-01

    For the generation of sound, some woodwind musical instruments, e.g. oboe, bassoon, clarinet and saxophone, are provided with mouthpieces made from reeds. These reeds are the culms of Arundo donax, a tall, cane-like perennial grass. A general problem is that the material is of varying quality, yet externally differences cannot be observed. Hence, large proportions of the prepared reeds are unusable. One hypothesis is that the changes in quality are correlated with differences in the chemical and anatomical structure of the tissue. Therefore, a comparison of superior and inferior mouthpieces, used by professional musicians, was undertaken to determinate potential indicators of quality. Nuclear microprobe analysis of reeds was carried out and complemented by scanning electron and light microscopy. The elemental levels of Si, P, S, Cl, K and Ca were compared between good and poor mouthpieces using appropriate statistical tests. No statistically significant differences could be identified. Microscopical observations showed that partial occlusion of vessels by tylose formation was associated with material deemed unusable

  1. Reed Watkins: A Passion for Plume Moths

    Science.gov (United States)

    Reed Watkins has curated the nationl Pterophordiae or plume moth collection at the National Museum of Natural History, Smithsonian Institution, for the past 13 years. He has decreased the number of specimens of unsorted and unidentified material and has expanded the collection from 3 to 6 cabinets....

  2. The Reed Elsevier stock price gap

    NARCIS (Netherlands)

    Kamp, B.

    1995-01-01

    This is the report of a limited study on the structural stock price differences between Reed and Elsevier. The purpose of this study is to provide an overview of the problem area and to formulate and discuss several hypotheses regarding the causes of this gap. The research was performed by

  3. Knowledge, access and utilization of bed-nets among stable and seasonal migrants in an artemisinin resistance containment area of Myanmar.

    Science.gov (United States)

    Phyo Than, Wint; Oo, Tin; Wai, Khin Thet; Thi, Aung; Owiti, Philip; Kumar, Binay; Deepak Shewade, Hemant; Zachariah, Rony

    2017-09-14

    Myanmar lies in the Greater Mekong sub-region of South-East Asia faced with the challenge of emerging resistance to artemisinin combination therapies (ACT). Migrant populations are more likely than others to spread ACT resistance. A vital intervention to reduce malaria transmission, resistance spread and eliminate malaria is the use of bed nets. Among seasonal and stable migrants in an artemisinin resistance containment region of Myanmar, we compared a) their household characteristics, b) contact with health workers and information material, and c) household knowledge, access and utilization of bed nets. Secondary data from community-based surveys on 2484 migrant workers (2013 and 2014, Bago Region) were analyzed of which 37% were seasonal migrants. Bed net access and utilization were assessed using a) availability of at least one bed net per household, and b) one bed net per two persons, and c) proportion of household members who slept under abed net during the previous night (Indicator targets = 100%). Over 70% of all migrants were from unstable work settings with short transitory stays. Average household size was five (range 1-25) and almost half of all households had children under-five years. Roughly 10 % of migrants were night-time workers. Less than 40% of households had contact with health workers and less than 30% had exposure to information education and communication (IEC) materials, the latter being significantly lower among seasonal migrants. About 70% of households were aware of the importance of insecticide-treated bed-nets/long-lasting insecticidal nets (ITNs/LLINs), but knowledge on insecticide impregnation and retreatment of ITNs was poor (Myanmar. Possible ways forward include frequent distribution campaigns to compensate for short transitory stays, matching household distributions to household size, enhanced information campaigns and introducing legislation to make mosquito repellents available for night-time workers at plantations and farms

  4. Knowledge, access and utilization of bed-nets among stable and seasonal migrants in an artemisinin resistance containment area of Myanmar

    OpenAIRE

    Phyo Than, Wint; Oo, Tin; Wai, Khin Thet; Thi, Aung; Owiti, Philip; Kumar, Binay; Deepak Shewade, Hemant; Zachariah, Rony

    2017-01-01

    Background Myanmar lies in the Greater Mekong sub-region of South-East Asia faced with the challenge of emerging resistance to artemisinin combination therapies (ACT). Migrant populations are more likely than others to spread ACT resistance. A vital intervention to reduce malaria transmission, resistance spread and eliminate malaria is the use of bed nets. Among seasonal and stable migrants in an artemisinin resistance containment region of Myanmar, we compared a) their household characterist...

  5. Regional Energy Deployment System (ReEDS)

    Energy Technology Data Exchange (ETDEWEB)

    Short, W.; Sullivan, P.; Mai, T.; Mowers, M.; Uriarte, C.; Blair, N.; Heimiller, D.; Martinez, A.

    2011-12-01

    The Regional Energy Deployment System (ReEDS) is a deterministic optimization model of the deployment of electric power generation technologies and transmission infrastructure throughout the contiguous United States into the future. The model, developed by the National Renewable Energy Laboratory's Strategic Energy Analysis Center, is designed to analyze the critical energy issues in the electric sector, especially with respect to potential energy policies, such as clean energy and renewable energy standards or carbon restrictions. ReEDS provides a detailed treatment of electricity-generating and electrical storage technologies and specifically addresses a variety of issues related to renewable energy technologies, including accessibility and cost of transmission, regional quality of renewable resources, seasonal and diurnal generation profiles, variability of wind and solar power, and the influence of variability on the reliability of the electrical grid. ReEDS addresses these issues through a highly discretized regional structure, explicit statistical treatment of the variability in wind and solar output over time, and consideration of ancillary services' requirements and costs.

  6. Channeling Your Donna Reed Syndrome.

    Science.gov (United States)

    Mercer County Community Coll., Trenton, NJ.

    This document offers materials on stress management used in a workplace literacy project developed by Mercer County Community College (New Jersey) and its partners. The document contains handouts on the following topics: (1) description of learners' typical days and identification of their stress points; (2) what stress is and is not; (3) a…

  7. "ON ALGEBRAIC DECODING OF Q-ARY REED-MULLER AND PRODUCT REED-SOLOMON CODES"

    Energy Technology Data Exchange (ETDEWEB)

    SANTHI, NANDAKISHORE [Los Alamos National Laboratory

    2007-01-22

    We consider a list decoding algorithm recently proposed by Pellikaan-Wu for q-ary Reed-Muller codes RM{sub q}({ell}, m, n) of length n {le} q{sup m} when {ell} {le} q. A simple and easily accessible correctness proof is given which shows that this algorithm achieves a relative error-correction radius of {tau} {le} (1-{radical}{ell}q{sup m-1}/n). This is an improvement over the proof using one-point Algebraic-Geometric decoding method given in. The described algorithm can be adapted to decode product Reed-Solomon codes. We then propose a new low complexity recursive aJgebraic decoding algorithm for product Reed-Solomon codes and Reed-Muller codes. This algorithm achieves a relative error correction radius of {tau} {le} {Pi}{sub i=1}{sup m} (1 - {radical}k{sub i}/q). This algorithm is then proved to outperform the Pellikaan-Wu algorithm in both complexity and error correction radius over a wide range of code rates.

  8. 77 FR 26321 - Reed College, Reed Research Nuclear Reactor, Renewed Facility Operating License No. R-112

    Science.gov (United States)

    2012-05-03

    ... Nuclear Reactor, Renewed Facility Operating License No. R-112 AGENCY: Nuclear Regulatory Commission... Commission (NRC or the Commission) has issued renewed Facility Operating License No. R- 112, held by Reed... License No. R-112 will expire 20 years from its date of issuance. The renewed facility operating license...

  9. Upgrated fuel from reed canary grass

    Energy Technology Data Exchange (ETDEWEB)

    Oravainen, H. [VTT Energy, Jyvaeskylae (Finland)

    1997-12-01

    Results described in this presentation are from a large EU-project - Development of a new crop production system based on delayed harvesting and system for its combined processing to chemical pulp and biofuel powder. This is a project to develop the use of Reed Canary Grass (Phalaris Arundinaceae) both for pulp industry and energy production. The main contractor of the project is Swedish University of Agricultural Sciences (coordinator), task coordinators are United Milling Systems A/S from Denmark, and Jaakko Poeyry Oy and VTT Energy from Finland In addition, there are partners from several countries participating in the project

  10. Implementation of Bin Packing Model for Reed Switch Production Planning

    Energy Technology Data Exchange (ETDEWEB)

    Parra, Rainier Romero [Polytechnic University of Baja California, Calle de la Claridad S/N, Col Plutarco Elias Calles, Mexicali, B. C., 21376 (Mexico); Burtseva, Larysa [Engineering Institute, Autonomous University of Baja California, Calle de la Normal S/N, Col. Insurgentes Este, Mexicali, BC, 21280 (Mexico)

    2010-06-17

    This paper presents a form to resolve a real problem of efficient material election in reed switch manufacturing. The carrying out of the consumer demands depends on the stochastic results of the classification process where each lot of switches is distributed into bins according to an electric measure value. Various glass types are employed for the switch manufacturing. The effect caused by the glass type variation on the switch classification results was investigated. Based on real data statistic analysis, the problem is reduced to the lot number minimizing taking into consideration the glass type, and interpreted as a bin packing problem generalization. On difference to the classic bin packing problem, in the considered case, an item represents a set of pieces; a container is divided into a number of bins (sub-containers); the bin capacity is variable; there are the assignment restrictions between bins and sets of pieces; the items are allowed to be fragmented into bins and containers. The problem has a high complexity. A heuristic offline algorithm is proposed to find the quantity, types and packing sequence of containers, the item fragments associated with containers and bins. The bin capacities do not affect the algorithm.

  11. Implementation of Bin Packing Model for Reed Switch Production Planning

    International Nuclear Information System (INIS)

    Parra, Rainier Romero; Burtseva, Larysa

    2010-01-01

    This paper presents a form to resolve a real problem of efficient material election in reed switch manufacturing. The carrying out of the consumer demands depends on the stochastic results of the classification process where each lot of switches is distributed into bins according to an electric measure value. Various glass types are employed for the switch manufacturing. The effect caused by the glass type variation on the switch classification results was investigated. Based on real data statistic analysis, the problem is reduced to the lot number minimizing taking into consideration the glass type, and interpreted as a bin packing problem generalization. On difference to the classic bin packing problem, in the considered case, an item represents a set of pieces; a container is divided into a number of bins (sub-containers); the bin capacity is variable; there are the assignment restrictions between bins and sets of pieces; the items are allowed to be fragmented into bins and containers. The problem has a high complexity. A heuristic offline algorithm is proposed to find the quantity, types and packing sequence of containers, the item fragments associated with containers and bins. The bin capacities do not affect the algorithm.

  12. Electrochemical treatment of water containing Microcystis aeruginosa in a fixed bed reactor with three-dimensional conductive diamond anodes

    International Nuclear Information System (INIS)

    Mascia, Michele; Monasterio, Sara; Vacca, Annalisa; Palmas, Simonetta

    2016-01-01

    Highlights: • Inactivation of M. aeruginosa was achieved by electrolysis with BDD anodes. • A fixed bed reactor with 3-D electrodes was tested in batch and continuous mode. • The kinetics of the process was determined from batch experiments. • A mathematical model of the process was implemented and validated. • The model was used to predict the system behaviour under different conditions. - Abstract: An electrochemical treatment was investigated to remove Microcystis aeruginosa from water. A fixed bed reactor in flow was tested, which was equipped with electrodes constituted by stacks of grids electrically connected in parallel, with the electric field parallel to the fluid flow. Conductive diamond were used as anodes, platinised Ti as cathode. Electrolyses were performed in continuous and in batch recirculated mode with flow rates corresponding to Re from 10 to 160, current densities in the range 10–60 A m −2 and Cl − concentrations up to 600 g m −3 . The absorbance of chlorophyll-a pigment and the concentration of products and by-products of electrolysis were measured. In continuous experiments without algae in the inlet stream, total oxidants concentrations as equivalent Cl 2 , of about 0.7 g Cl 2 m −3 were measured; the maximum values were obtained at Re = 10 and i = 25 A m −2 , with values strongly dependent on the concentration of Cl − . The highest algae inactivation was obtained under the operative conditions of maximum generation of oxidants; in the presence of microalgae the oxidants concentrations were generally below the detection limit. Results indicated that most of the bulk oxidants electrogenerated is constituted by active chlorine. The prevailing mechanism of M. aeruginosa inactivation is the disinfection by bulk oxidants. The experimental data were quantitatively interpreted through a simple plug flow model, in which the axial dispersion accounts for the non-ideal flow behaviour of the system; the model was successfully

  13. Electrochemical treatment of water containing Microcystis aeruginosa in a fixed bed reactor with three-dimensional conductive diamond anodes

    Energy Technology Data Exchange (ETDEWEB)

    Mascia, Michele, E-mail: michele.mascia@unica.it; Monasterio, Sara; Vacca, Annalisa; Palmas, Simonetta

    2016-12-05

    Highlights: • Inactivation of M. aeruginosa was achieved by electrolysis with BDD anodes. • A fixed bed reactor with 3-D electrodes was tested in batch and continuous mode. • The kinetics of the process was determined from batch experiments. • A mathematical model of the process was implemented and validated. • The model was used to predict the system behaviour under different conditions. - Abstract: An electrochemical treatment was investigated to remove Microcystis aeruginosa from water. A fixed bed reactor in flow was tested, which was equipped with electrodes constituted by stacks of grids electrically connected in parallel, with the electric field parallel to the fluid flow. Conductive diamond were used as anodes, platinised Ti as cathode. Electrolyses were performed in continuous and in batch recirculated mode with flow rates corresponding to Re from 10 to 160, current densities in the range 10–60 A m{sup −2} and Cl{sup −} concentrations up to 600 g m{sup −3}. The absorbance of chlorophyll-a pigment and the concentration of products and by-products of electrolysis were measured. In continuous experiments without algae in the inlet stream, total oxidants concentrations as equivalent Cl{sub 2}, of about 0.7 g Cl{sub 2} m{sup −3} were measured; the maximum values were obtained at Re = 10 and i = 25 A m{sup −2}, with values strongly dependent on the concentration of Cl{sup −}. The highest algae inactivation was obtained under the operative conditions of maximum generation of oxidants; in the presence of microalgae the oxidants concentrations were generally below the detection limit. Results indicated that most of the bulk oxidants electrogenerated is constituted by active chlorine. The prevailing mechanism of M. aeruginosa inactivation is the disinfection by bulk oxidants. The experimental data were quantitatively interpreted through a simple plug flow model, in which the axial dispersion accounts for the non-ideal flow behaviour of the

  14. Reed as a gasification fuel: a comparison with woody fuels

    Directory of Open Access Journals (Sweden)

    S. Link

    2013-10-01

    Full Text Available Reed and coniferous wood can be used for energy production via thermochemical conversion, for instance by gasification. The rate-determining step of the gasification process is the reaction between the char and the gaseous environment in the gasifier, whose rate depends on variables such as pressure, temperature, particle size, mineral matter content, porosity, etc. It is known that reactivity can be improved by increasing the temperature, but on the other hand the temperature achieved in the reactor is limited due to the ash fusion characteristics. Usually, the availability of reed as a fuel is locally modest and, therefore, it must be blended with other fuels such as wood. Blending of fuels brings together several problems relating to ash behaviour, i.e. ash fusion issues. Because there is no correlation between the ash fusion characteristics of biomass blends and their individual components, it is essential to carry out prior laboratory-scale ash fusion tests on the blends. This study compares the reactivity of reed and coniferous wood, and the ash fusion characteristics of blends of reed and coniferous wood ashes. When compared with Douglas fir and reed chars, pine pellets have the highest reactivity. Reed char exhibits the lowest reactivity and, therefore, it is advantageous to gasify reed alone at higher gasification temperatures because the ash fusion temperatures of reed are higher than those of woody fuels. The ash produced by reed and wood blends can melt at lower temperatures than ash from both reed and wood gasified separately. Due to this circumstance the gasification temperature should be chosen carefully when gasification of blends is carried out.

  15. Effects of reed cutting on density and breeding success of reed warbler Acrocephalus scirpacaeus and sedge warbler A. schoenobaenus

    NARCIS (Netherlands)

    Graveland, J.

    1999-01-01

    The management of reedbeds for birds is often a controversial issue in discussions between conservationists, reed harvesters and managers. At the same time, data on the density and nesting success of birds in cut and uncut reed are scarce. This paper presents the results of a study on the density

  16. An assessment of the risk of embrittlement of a steel container by hydrogen picked up on the ocean bed

    International Nuclear Information System (INIS)

    Hardie, D.

    1985-09-01

    A realistic assessment of the likelihood of embrittlement of a plain carbon steel container for nuclear waste has been made by estimating the hydrogen levels that might be expected to develop in the steel as a consequence of the slow corrosion of the container and the possible effect that such a hydrogen concentration would have on its mechanical behaviour. By consideration of various possible models for the generation of hydrogen and its subsequent uptake into the steel or dissemination in the environment, it is concluded that the most pessimistic assessment of the concentration of hydrogen that could build up in the container walls during 1000 years burial would not significantly affect the resistance to failure of even relatively high strength steels. (author)

  17. Electrochemical treatment of water containing Microcystis aeruginosa in a fixed bed reactor with three-dimensional conductive diamond anodes.

    Science.gov (United States)

    Mascia, Michele; Monasterio, Sara; Vacca, Annalisa; Palmas, Simonetta

    2016-12-05

    An electrochemical treatment was investigated to remove Microcystis aeruginosa from water. A fixed bed reactor in flow was tested, which was equipped with electrodes constituted by stacks of grids electrically connected in parallel, with the electric field parallel to the fluid flow. Conductive diamond were used as anodes, platinised Ti as cathode. Electrolyses were performed in continuous and in batch recirculated mode with flow rates corresponding to Re from 10 to 160, current densities in the range 10-60Am(-2) and Cl(-) concentrations up to 600gm(-3). The absorbance of chlorophyll-a pigment and the concentration of products and by-products of electrolysis were measured. In continuous experiments without algae in the inlet stream, total oxidants concentrations as equivalent Cl2, of about 0.7gCl2m(-3) were measured; the maximum values were obtained at Re=10 and i=25Am(-2), with values strongly dependent on the concentration of Cl(-). The highest algae inactivation was obtained under the operative conditions of maximum generation of oxidants; in the presence of microalgae the oxidants concentrations were generally below the detection limit. Results indicated that most of the bulk oxidants electrogenerated is constituted by active chlorine. The prevailing mechanism of M. aeruginosa inactivation is the disinfection by bulk oxidants. The experimental data were quantitatively interpreted through a simple plug flow model, in which the axial dispersion accounts for the non-ideal flow behaviour of the system; the model was successfully used to simulate the performances of the reactor in the single-stack configuration used for the experiments and in multi-stack configurations. Copyright © 2016 Elsevier B.V. All rights reserved.

  18. Bed Bugs

    Science.gov (United States)

    Prevent, identify, and treat bed bug infestations using EPA’s step-by-step guides, based on IPM principles. Find pesticides approved for bed bug control, check out the information clearinghouse, and dispel bed bug myths.

  19. Containment

    International Nuclear Information System (INIS)

    Anon.

    1987-01-01

    The primary mission of the Containment Group is to ensure that underground nuclear tests are satisfactorily contained. The main goal is the development of sound technical bases for containment-related methodology. Major areas of activity include siting, geologic description, emplacement hole stemming, and phenomenological predictions. Performance results of sanded gypsum concrete plugs on the Jefferson, Panamint, Cornucopia, Labquark, and Bodie events are given. Activities are also described in the following areas: computational capabilities site description, predictive modeling, and cavity-pressure measurement. Containment publications are listed. 8 references

  20. Supercritical fluid extraction of reed (thypa)

    Energy Technology Data Exchange (ETDEWEB)

    Kucuk, M.; Genel, Y. [YYU Educational Faculty, Van (Turkey); Demir, H. [YYU Science and Art Faculty, Van (Turkey)

    2005-04-15

    Reed (typha) mill was converted to liquid products by using organic solvents (methanol, ethanol and acetone) with catalysts (% 10 NaOH and ZnCl{sub 2}) and without catalyst in an autoclave at temperatures of 533, 553, and 573 K. The liquid products were extracted by liquid-liquid extraction [DSA1] (benzene and diethyl ether). The yields from supercritical methanol, ethanol and acetone conversions were 36.2, 24.5, and 55.1%, respectively, at 573 K. In the catalytic runs with methanol and ethanol extracts were 46.3 and 35.5% (for NaOH catalyst) and 51.8 and 38.5% (for ZnCl{sub 2} catalyst) respectively, at 573 K. The yields from supercritical methanol were increased from 38.2 to 52.4% as the temperature was increased from 533 to 573 K in the catalytic run. (Author)

  1. Aerodynamic excitation and sound production of blown-closed free reeds without acoustic coupling: The example of the accordion reed

    Science.gov (United States)

    Ricot, Denis; Caussé, René; Misdariis, Nicolas

    2005-04-01

    The accordion reed is an example of a blown-closed free reed. Unlike most oscillating valves in wind musical instruments, self-sustained oscillations occur without acoustic coupling. Flow visualizations and measurements in water show that the flow can be supposed incompressible and potential. A model is developed and the solution is calculated in the time domain. The excitation force is found to be associated with the inertial load of the unsteady flow through the reed gaps. Inertial effect leads to velocity fluctuations in the reed opening and then to an unsteady Bernoulli force. A pressure component generated by the local reciprocal air movement around the reed is added to the modeled aerodynamic excitation pressure. Since the model is two-dimensional, only qualitative comparisons with air flow measurements are possible. The agreement between the simulated pressure waveforms and measured pressure in the very near-field of the reed is reasonable. In addition, an aeroacoustic model using the permeable Ffowcs Williams-Hawkings integral method is presented. The integral expressions of the far-field acoustic pressure are also computed in the time domain. In agreement with experimental data, the sound is found to be dominated by the dipolar source associated by the strong momentum fluctuations of the flow through the reed gaps. .

  2. Attaching Copper Wires to Magnetic-Reed-Switch Leads

    Science.gov (United States)

    Kamila, Rudolf

    1987-01-01

    Bonding method reliably joins copper wires to short iron-alloy leads from glass-encased dry magnetic-reed switch without disturbing integrity of glass-to-metal seal. Joint resistant to high temperatures and has low electrical resistance.

  3. Decoding Reed-Solomon Codes beyond half the minimum distance

    DEFF Research Database (Denmark)

    Høholdt, Tom; Nielsen, Rasmus Refslund

    1999-01-01

    We describe an efficient implementation of M.Sudan"s algorithm for decoding Reed-Solomon codes beyond half the minimum distance. Furthermore we calculate an upper bound of the probabilty of getting more than one codeword as output...

  4. One way quantum repeaters with quantum Reed-Solomon codes

    OpenAIRE

    Muralidharan, Sreraman; Zou, Chang-Ling; Li, Linshu; Jiang, Liang

    2018-01-01

    We show that quantum Reed-Solomon codes constructed from classical Reed-Solomon codes can approach the capacity on the quantum erasure channel of $d$-level systems for large dimension $d$. We study the performance of one-way quantum repeaters with these codes and obtain a significant improvement in key generation rate compared to previously investigated encoding schemes with quantum parity codes and quantum polynomial codes. We also compare the three generation of quantum repeaters using quan...

  5. Biology, Management and Utilization of Common Reed Pharagnites australis.

    Science.gov (United States)

    1987-02-01

    Vrije Universiteit Waterways Experiment Staticn Department of Ecology and Ecotoxicology Environmental Laboratory P.O. Box 7161 P.O. Box 631 1007 MC...Madelijn van der Werff Vrije Universiteit Department of Ecology and Ecotoxicology Amsterdam and John W. Simmers and Stratford H. Kay Waterways...lowing and cutting 67 5.2.4. Active regulation of the water table 68 5.5. Nature conservation 68 5.4. Reed cultivation 69 Z.4. 1. Reed harvest 69 6

  6. Float level switch for a nuclear power plant containment vessel

    International Nuclear Information System (INIS)

    Powell, J.G.

    1993-01-01

    This invention is a float level switch used to sense rise or drop in water level in a containment vessel of a nuclear power plant during a loss of coolant accident. The essential components of the device are a guide tube, a reed switch inside the guide tube, a float containing a magnetic portion that activates a reed switch, and metal-sheathed, ceramic-insulated conductors connecting the reed switch to a monitoring system outside the containment vessel. Special materials and special sealing techniques prevent failure of components and allow the float level switch to be connected to a monitoring system outside the containment vessel. 1 figures

  7. Float level switch for a nuclear power plant containment vessel

    Science.gov (United States)

    Powell, James G.

    1993-01-01

    This invention is a float level switch used to sense rise or drop in water level in a containment vessel of a nuclear power plant during a loss of coolant accident. The essential components of the device are a guide tube, a reed switch inside the guide tube, a float containing a magnetic portion that activates a reed switch, and metal-sheathed, ceramic-insulated conductors connecting the reed switch to a monitoring system outside the containment vessel. Special materials and special sealing techniques prevent failure of components and allow the float level switch to be connected to a monitoring system outside the containment vessel.

  8. Long term effects of ash fertilization of reed canary grass; Laangtidseffekter av askgoedsling vid roerflensodling

    Energy Technology Data Exchange (ETDEWEB)

    Palmborg, Cecilia; Lindvall, Eva

    2011-03-15

    Reed canary grass (RCG) is a bio-energy crop with large potential. It is a 1.5 . 2.5 m tall grass that is harvested in spring when it is grown as a fuel. At spring harvest it yields 3 . 10 ton field dried material per ha and year. One disadvantage when reed canary grass is used as a fuel is the high ash content, 5-10 %. This means that large quantities of ash have to be deposited which is expensive, about 1000 SEK/ton. However, since reed canary grass ash contains reasonable amounts of plant nutrients like phosphorous (P), potassium (K) and magnesium (Mg) it could be recycled as fertilizer in agriculture. The ash can be used without any pretreatment since, in agriculture, plant availability is desirable. The aim of this project, was to evaluate a field experiment, where ash was used as a fertilizer in reed canary grass. The experiment was established at the SLU research station in Umea, Sweden in the spring 2002. Three different fertilizer treatments were applied: Treatment A was fertilized with an ash produced by combustion of RCG together with municipal wastes (paper, plastic, leather), treatment B, an ash from combustion of RCG, and for treatment C commercial fertilizers were used. In total, 100 kg ha-1 of nitrogen (N), 15 kg ha-1 of phosphorous (P) and 80 kg ha-1 of potassium (K), were applied each year in all treatments. The amount of ash in treatment A and B was calculated from the chemical analysis of the ashes to be equal to the required amount of P, while K and N were supplied also by commercial fertilizers. [Table 1. Composition of the ashes] Literature study: There is a lack of knowledge about fertilization with reed canary grass ash, since few experiments have been conducted. The composition of reed canary grass is dependent of harvest date and the soil substrate. The amount of ash and the amount of harmful substances such as potassium and chloride generally decreases over winter, giving an increased fuel quality from spring harvest compared to autumn

  9. Upgraded fuel from reed canary grass

    Energy Technology Data Exchange (ETDEWEB)

    Heiskanen, V P

    1996-12-31

    The feasibility of RCG for commercial utilization depends primarily on its applicability for pulp production and its use in energy production will be based on the residue that will be available after extracting the pulp fraction of the RCG. Roughly 20 ..30% of the material will be available for energy production purposes. However, the percentage may be higher/lower depending on the quality standards of the pulp fiber material. The harvesting period has a significant effect on the fuel characteristics of RCG. For instance the contents of N, S, Cl, K are clearly lower if the RCG is harvested in the spring (delayed) instead of summer/autumn. These elements affect significantly overall emission formation and ash behaviour and its melting temperature. The combustion related research in this project has been focused on the spring-harvested RCG. The project aims to evaluate the feasibility of delayed harvested RCG for energy production. In order to reach this goal, the following combustion methods will be tested and studied: combustion of pelletized RCG; gasification; combustion of pulverized RCG. In addition, pelletizing, reactivity and NO conversion of pulverized RCG will be studied. The research described here is a part of `Reed Canary Grass` project (in AIR programme). The contractors of the project are Swedish University of Agricultural Sciences (coordinator), United Milling Systems from Denmark, Jaakko Poeyry Oy and VTT Energy. In addition, there are partners from several countries participating in the project. The project has been divided in five tasks, VTT Energy being responsible for combustion related task `Upgraded fuel` that includes the research topics discussed in this paper

  10. Upgraded fuel from reed canary grass

    Energy Technology Data Exchange (ETDEWEB)

    Heiskanen, V.P.

    1995-12-31

    The feasibility of RCG for commercial utilization depends primarily on its applicability for pulp production and its use in energy production will be based on the residue that will be available after extracting the pulp fraction of the RCG. Roughly 20 ..30% of the material will be available for energy production purposes. However, the percentage may be higher/lower depending on the quality standards of the pulp fiber material. The harvesting period has a significant effect on the fuel characteristics of RCG. For instance the contents of N, S, Cl, K are clearly lower if the RCG is harvested in the spring (delayed) instead of summer/autumn. These elements affect significantly overall emission formation and ash behaviour and its melting temperature. The combustion related research in this project has been focused on the spring-harvested RCG. The project aims to evaluate the feasibility of delayed harvested RCG for energy production. In order to reach this goal, the following combustion methods will be tested and studied: combustion of pelletized RCG; gasification; combustion of pulverized RCG. In addition, pelletizing, reactivity and NO conversion of pulverized RCG will be studied. The research described here is a part of `Reed Canary Grass` project (in AIR programme). The contractors of the project are Swedish University of Agricultural Sciences (coordinator), United Milling Systems from Denmark, Jaakko Poeyry Oy and VTT Energy. In addition, there are partners from several countries participating in the project. The project has been divided in five tasks, VTT Energy being responsible for combustion related task `Upgraded fuel` that includes the research topics discussed in this paper

  11. Hydrodynamic calculation of a filter sand bed type used in the containment venting systems; Calculo hidrodinamico de un filtro tipo lecho de arena usado en los sistemas de venteo de la contencion

    Energy Technology Data Exchange (ETDEWEB)

    Cuevas V, D.; Sainz M, E.; Ortiz V, J., E-mail: delfy.cu@gmail.com [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2015-09-15

    The filtered venting of the containment has been adopted in European countries to mitigate the consequences of excess pressure containment during a severe accident. When venting has taken place, the fission products are released directly into the environment, unless a filter on the same path is placed, so that various types of filters are used to trap the fission products. The venting filters of the containment currently installed use different filtration technologies that involve more than one medium. Those using water as the first stage of filtration are called wet systems and are equipped with additional steps to remove water drops and fine aerosols emissions. And even they may also be equipped with an element containing certain absorption means for the filtration of gaseous iodine species. Other designs based on filtration of deep bed as the primary retention step; called dry filters, use filtration media of metal fiber, ceramic or sand to trap aerosols. This paper evaluates the hydraulic characteristics of the filter sand bed type designed by EDF as a candidate to be installed in the containment of BWR Mark II (type of primary containment of the nuclear power plant of Laguna Verde). The evaluation of filter sand bed type was performed using the software package of open source OpenFOAM. Models of each zone of the filtered device were generated and through a series of parametric calculations of computational fluid mechanics relevant hydrodynamic characteristics of the device were obtained, such as pressure drops against mass flow rate and pressure fields and speed at different operating conditions. On the other hand, the model validation of the sand bed filter when comparing the results of experimental tests on a sand column of PITEAS program (1985-1986) against OpenFOAM simulation was realized. The results are very close to those obtained experimentally. (Author)

  12. 77 FR 43369 - Lexisnexis, a Subsidiary of Reed Elsevier Customer Service Department and Fulfillment Department...

    Science.gov (United States)

    2012-07-24

    ..., a Subsidiary of Reed Elsevier Customer Service Department and Fulfillment Department, Including On... Including Remote Workers in New York Reporting to Miamisburg, OH; Lexisnexis, a Subsidiary of Reed Elsevier... subsidiary of Reed Elsevier, Inc., Customer Service Department and Fulfillment Department, including on-site...

  13. GluN2B-containing NMDA receptors blockade rescues bidirectional synaptic plasticity in the bed nucleus of the stria terminalis of cocaine self-administering rats.

    Science.gov (United States)

    deBacker, Julian; Hawken, Emily R; Normandeau, Catherine P; Jones, Andrea A; Di Prospero, Cynthia; Mechefske, Elysia; Gardner Gregory, James; Hayton, Scott J; Dumont, Éric C

    2015-01-01

    Drugs of abuse have detrimental effects on homeostatic synaptic plasticity in the motivational brain network. Bidirectional plasticity at excitatory synapses helps keep neural circuits within a functional range to allow for behavioral flexibility. Therefore, impaired bidirectional plasticity of excitatory synapses may contribute to the behavioral hallmarks of addiction, yet this relationship remains unclear. Here we tracked excitatory synaptic strength in the oval bed nucleus of the stria terminalis (ovBNST) using whole-cell voltage-clamp recordings in brain slices from rats self-administering sucrose or cocaine. In the cocaine group, we measured both a persistent increase in AMPA to NMDA ratio (A:N) and slow decay time of NMDA currents throughout the self-administration period and after withdrawal from cocaine. In contrast, the sucrose group exhibited an early increase in A:N ratios (acquisition) that returned toward baseline values with continued self-administration (maintenance) and after withdrawal. The sucrose rats also displayed a decrease in NMDA current decay time with continued self-administration (maintenance), which normalized after withdrawal. Cocaine self-administering rats exhibited impairment in NMDA-dependent long-term depression (LTD) that could be rescued by GluN2B-containing NMDA receptor blockade. Sucrose self-administering rats demonstrated no impairment in NMDA-dependent LTD. During the maintenance period of self-administration, in vivo (daily intraperitoneally for 5 days) pharmacologic blockade of GluN2B-containing NMDA receptors did not reduce lever pressing for cocaine. However, in vivo GluN2B blockade did normalize A:N ratios in cocaine self-administrating rats, and dissociated the magnitude of ovBNST A:N ratios from drug-seeking behavior after protracted withdrawal. Altogether, our data demonstrate when and how bidirectional plasticity at ovBNST excitatory synapses becomes dysfunctional with cocaine self-administration and that NMDA

  14. Bodems voor vrijloopstallen = Bedding materials in loose housing systems for dairy cattle

    NARCIS (Netherlands)

    Dooren, van H.J.C.; Galama, P.J.; Smits, M.C.J.

    2012-01-01

    Sand, Compost and 'toemaak' (a mixture of reed, dredge and manure) had been used as bedding material for loose housing systems on three dairy research farms of Wageningen UR Livestock Research. Gaseous emissions, animal behavior and health and food safety aspects were measured and reported together

  15. 39th annual Reed rig census

    International Nuclear Information System (INIS)

    Crowhurst, M.E.; Fitts, R.L.

    1991-01-01

    This paper reports on cutbacks in U.S. exploration and development drilling during the first half of 1991 which squeezed most of the optimism out of the drilling industry. Just how rough the year has been is underscored by the results of this year's rig census. The number of rotary rigs available for U.S. drilling declined by only 69 units (3%) during the past 12 months. But despite those withdrawals from competition, only 66% of the remaining rigs were working at the time the census was taken. Results of the 1991 census contrasted sharply with the stability and optimism that seemed apparent a year ago when 72% of the available rig fleet met the census definition of active. At that time, the mini-boom in horizontal drilling coupled with tax-credit- driven gas drilling led to a relatively high rig utilization rate and suggested that rig supply and demand might be close to an economically acceptable balance. However, it quickly became apparent in early 1991 that industry optimism was unjustified. Horizontal drilling began to drop and the lowest natural gas prices in 12 years triggered rapid declines in gas drilling. Although oil prices have been relatively stable and above $18 per bbl since January 1989, most major operators have concluded that a better return on investment can be had outside the U.S. and have drastically cut their domestic drilling budgets. These factors, combined with softened energy demand from the worldwide recession, further slowed U.S. drilling. The long awaited balance between rig supply and demand has seemingly slipped away. The 1991 Reed rig census describes an industry facing several more rough years. Details of this year's census include: The available U.S. fleet now stands at 2,251 rigs, down by 69 from the 2,320-unit total in 1990, and the lowest since 1976. Rigs meeting the census definition of active numbered 1,485, down 192 (11.4%) from the 1,677 active rigs counted a year earlier

  16. Particle fuel bed tests

    International Nuclear Information System (INIS)

    Horn, F.L.; Powell, J.R.; Savino, J.M.

    1985-01-01

    Gas-cooled reactors, using packed beds of small diameter coated fuel particles have been proposed for compact, high-power systems. The particulate fuel used in the tests was 800 microns in diameter, consisting of a thoria kernel coated with 200 microns of pyrocarbon. Typically, the bed of fuel particles was contained in a ceramic cylinder with porous metallic frits at each end. A dc voltage was applied to the metallic frits and the resulting electric current heated the bed. Heat was removed by passing coolant (helium or hydrogen) through the bed. Candidate frit materials, rhenium, nickel, zirconium carbide, and zirconium oxide were unaffected, while tungsten and tungsten-rhenium lost weight and strength. Zirconium-carbide particles were tested at 2000 K in H 2 for 12 hours with no visible reaction or weight loss

  17. Vectorization of Reed Solomon decoding and mapping on the EVP

    NARCIS (Netherlands)

    Kumar, A.; Berkel, van C.H.

    2008-01-01

    Reed Solomon (RS) codes are used in a variety of (wireless) communication systems. Although commonly implemented in dedicated hardware, this paper explores the mapping of high-throughput RS decoding on vector DSPs. The four modules of such a decoder, viz. Syndrome Computation, Key Equation Solver,

  18. Disrupting the Education Monopoly: A Conversation with Reed Hastings

    Science.gov (United States)

    Jacobs, Joanne

    2015-01-01

    This article features an interview with Netflix CEO, Reed Hastings. In this interview, Hastings relates that he told the "Wall Street Journal" in 2008 that he started looking at education--trying to figure out why our education is lagging when our technology is increasing at great rates and there's great innovation in so many other areas…

  19. An Exemplary High School Literary Magazine: "The Thinking Reed."

    Science.gov (United States)

    Holbrook, Hilary Taylor, Comp.

    One of a series of 20 literary magazine profiles written to help faculty advisors wishing to start or improve their publication, this profile provides information on staffing and production of "The Thinking Reed," the magazine published by Bethlehem Central High School, Delmar, New York. The introduction describes the literary magazine…

  20. Reeds as indicators of nutrient enrichment in a small temporarily ...

    African Journals Online (AJOL)

    Nutrient (NH4 and SRP) concentrations decreased from the bank towards the main estuary channel, suggesting that nutrients introduced into the estuary in groundwater and surface runoff were taken up by the fringe of reeds. The roots, rhizomes, stems and leaves of Phragmites at the site with the greatest Phragmites ...

  1. Utility of Recycled Bedding for Laboratory Rodents

    OpenAIRE

    Miyamoto, Toru; Li, Zhixia; Kibushi, Tomomi; Okano, Shinya; Yamasaki, Nakamichi; Kasai, Noriyuki

    2009-01-01

    Animal facilities generate a large amount of used bedding containing excrement as medical waste. We developed a recycling system for used bedding that involves soft hydrothermal processing. In this study, we examined the effects of bedding type on growth, hematologic and serum biochemical values, and organ weights of female and male mice reared on either recycled or fresh bedding from 3 to 33 wk of age. Neither growth nor physiology differed between mice housed on recycled bedding compared wi...

  2. Pebble-bed reactor

    International Nuclear Information System (INIS)

    Lohnert, G.; Mueller-Frank, U.; Heil, J.

    1976-01-01

    A pebble-bed nuclear reactor of large power rating comprises a container having a funnel-shaped bottom forming a pebble run-out having a centrally positioned outlet. A bed of downwardly-flowing substantially spherical nuclear fuel pebbles is positioned in the container and forms a reactive nuclear core maintained by feeding unused pebbles to the bed's top surface while used or burned-out pebbles run out and discharge through the outlet. A substantially conical body with its apex pointing upwardly and its periphery spaced from the periphery of the container spreads the bottom of the bed outwardly to provide an annular flow down the funnel-shaped bottom forming the runout, to the discharge outlet. This provides a largely constant downward velocity of the spheres throughout the diameter of the bed throughout a substantial portion of the down travel, so that all spheres reach about the same burned-out condition when they leave the core, after a single pass through the core area

  3. Reed Reactor Facility final report, September 1, 1994--August 31, 1995

    International Nuclear Information System (INIS)

    1997-01-01

    This report covers the period from September 1, 1994 to August 31, 1995. Information contained in this report is intended to fulfill several purposes including the reporting requirements of the US Nuclear Regulatory Commission (USNRC), the US Department of Energy (USDOE), and the Oregon Department of Energy (ODOE). Highlights of the last year include: student participation in the program is very high; the facility has been extraordinarily successful in obtaining donated equipment from Portland General Electric, US Department of Energy, Precision Castparts, Tektronix, and other sources; the facility is developing more paid work. There were 1,115 visits of the Reactor Facility by individuals during the year. Most of these visitors were students in classes at Reed College or area universities, colleges, and high schools. During the year, the reactor was operated 225 separate times on 116 days. The total energy production was 24.6 MW-hours. The reactor staff consists of a Director, an Associate Director, a contract Health Physicist, and approximately fifteen Reed College undergraduate students as hourly employees. All radiation exposures to individuals during this year were well below 1% of the federal limits. There were no releases of liquid radioactive material from the facility and airborne releases (primarily 41 Ar) were well within regulatory limits

  4. Reed Reactor Facility final report, September 1, 1994--August 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-01

    This report covers the period from September 1, 1994 to August 31, 1995. Information contained in this report is intended to fulfill several purposes including the reporting requirements of the US Nuclear Regulatory Commission (USNRC), the US Department of Energy (USDOE), and the Oregon Department of Energy (ODOE). Highlights of the last year include: student participation in the program is very high; the facility has been extraordinarily successful in obtaining donated equipment from Portland General Electric, US Department of Energy, Precision Castparts, Tektronix, and other sources; the facility is developing more paid work. There were 1,115 visits of the Reactor Facility by individuals during the year. Most of these visitors were students in classes at Reed College or area universities, colleges, and high schools. During the year, the reactor was operated 225 separate times on 116 days. The total energy production was 24.6 MW-hours. The reactor staff consists of a Director, an Associate Director, a contract Health Physicist, and approximately fifteen Reed College undergraduate students as hourly employees. All radiation exposures to individuals during this year were well below 1% of the federal limits. There were no releases of liquid radioactive material from the facility and airborne releases (primarily {sup 41}Ar) were well within regulatory limits.

  5. Ecology and physiology of reed. A literature study for evaluation of reed as an energy source. Vassens Ekologi och Fysiologi. Litteraturstudie foer Bedoerfrung au Vass som Energiraavaren

    Energy Technology Data Exchange (ETDEWEB)

    Bjoerndahl, G.; Egnens, H.

    1980-01-01

    The potentials of reed as an energy source are evaluated. The following subjects are discussed: The structure and life-cycle of reed; Primary production and photosynthesis; Important environmental factors for the production; Genetic variation; Competition, succession and parasitism; Human influence like cultivation, harvesting, etc. An extensive list of references is given.

  6. Mapping of reed in shallow bays. SFR-Site Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Stroemgren, Maarten; Lindgren, Fredrik (Umeaa Univ. (Sweden))

    2011-03-15

    The regolith-lake development model (RLDM) describes the development of shallow bays to lakes and the infilling of lakes in the Forsmark area during an interglacial. The sensitivity analysis has shown the need for an update of the infill procedure in the RLDM. Data from the mapping of reed in shallow bays in the Forsmark area will be used to improve the infill procedure of an updated RLDM. The field work was performed in August 26-31, 2010. The mapping of reed was done in 124 points. In these points, coordinates and water depth were mapped using an echo sounder and a DGPS. Quaternary deposits and the thickness of soft sediments were mapped using an earth probe. Measurement points were delivered in ESRI shape format with coordinates in RT90 2.5 gon W and altitudes in the RHB70 system for storage in SKB's GIS data base

  7. Oscillation thresholds for "striking outwards" reeds coupled to a resonator

    OpenAIRE

    Silva , Fabrice; Kergomard , Jean; Vergez , Christophe

    2007-01-01

    International audience; This paper considers a "striking outwards" reed coupled to a resonator. This expression, due to Helmholtz, is not discussed here : it corresponds to the most common model of a lip-type valve, when the valve is assumed to be a one degree of freedom oscillator. The presented work is an extension of the works done by Wilson and Beavers (1974), Tarnopolsky (2000). The range of the playing frequencies is investigated. The first results are analytical : when no losses are pr...

  8. Dorothy Reed and Hodgkin's disease: a reflection after a century

    International Nuclear Information System (INIS)

    Zwitter, Matjaz; Cohen, Joel R.; Barrett, Ann; Robinton, Elizabeth D.

    2002-01-01

    It has now been 100 years since Dorothy Reed, at the age of 28, wrote her paper on Hodgkin's disease. Her biography reveals the difficult lives of women entering the hitherto male-dominated field of medicine, let alone medical research. Her historic paper on Hodgkin's disease is remarkable for its brilliant observations and concise scientific reasoning. Nevertheless, she was told that as a woman she could not hope for a career as an academic pathologist. After marriage to Charles Elwood Mendenhall, Professor of Physics at the University of Wisconsin and after giving birth to four children, the second part of her career began. Motivated by the loss of her firstborn, she began a study of infant mortality, an interest that lasted throughout her career. In 1926, Mendenhall undertook a survey comparing infant and maternal mortality rates in Denmark and the United States. This influential study concluded that American mortality rates were higher because of unnecessary interference in the natural process of childbirth and recommended the education of midwives follow the Danish model. In 1937, her efforts were rewarded when Madison, WI received recognition for having the lowest infant mortality of any city in the United States. Reading Reed's paper on Hodgkin's disease, we see that her observations go far beyond a description of a specific cell. Her presentation of macroscopic and microscopic features is remarkable for the distinction between 'young' and 'old' growths: Reed saw Hodgkin's disease as a process, rather than the spreading of a cancer. She was the first to note that those most commonly affected are boys or young adults, especially those whose general health before the disease had been excellent. She was also the first to note anergy to tuberculin. Dorothy Reed defined Hodgkin's disease in relation to tuberculosis, described its pathologic features, and offered comments on its pathogenesis, epidemiology, and immunology that still deserve to be discussed

  9. Treatment of azo dye-containing wastewater by a Fenton-like process in a continuous packed-bed reactor filled with activated carbon

    Energy Technology Data Exchange (ETDEWEB)

    Mesquita, Isabel; Matos, Luis C. [Chemical Engineering Department, Faculty of Engineering, University of Porto, Rua Dr. Roberto Frias, 4200-465 Porto (Portugal); Duarte, Filipa [Chemical Engineering Department, Faculty of Engineering, University of Porto, Rua Dr. Roberto Frias, 4200-465 Porto (Portugal); LEPAE - Laboratory for Process, Environmental and Energy Engineering, Department of Chemical Engineering, Faculty of Engineering, University of Porto, Porto (Portugal); Maldonado-Hodar, F.J. [Department of Inorganic Chemistry, Faculty of Sciences, University of Granada, Av. Fuentenueva, 18071 Granada (Spain); Mendes, Adelio [Chemical Engineering Department, Faculty of Engineering, University of Porto, Rua Dr. Roberto Frias, 4200-465 Porto (Portugal); LEPAE - Laboratory for Process, Environmental and Energy Engineering, Department of Chemical Engineering, Faculty of Engineering, University of Porto, Porto (Portugal); Madeira, Luis M., E-mail: mmadeira@fe.up.pt [Chemical Engineering Department, Faculty of Engineering, University of Porto, Rua Dr. Roberto Frias, 4200-465 Porto (Portugal); LEPAE - Laboratory for Process, Environmental and Energy Engineering, Department of Chemical Engineering, Faculty of Engineering, University of Porto, Porto (Portugal)

    2012-10-30

    Highlights: Black-Right-Pointing-Pointer Oxidation with the Fenton's reagent was carried out in a packed-bed reactor. Black-Right-Pointing-Pointer The packed-bed was filled with iron-impregnated activated carbon. Black-Right-Pointing-Pointer The increment of temperature increases the Chicago Sky Blue removal and mineralization. Black-Right-Pointing-Pointer The values of iron leaching were below 0.4 ppm in the outlet effluent. Black-Right-Pointing-Pointer It was possible to reach a dye conversion of 88% in steady-state. - Abstract: In this work, oxidation with a Fenton-like process of a dye solution was carried out in a packed-bed reactor. Activated carbon Norit RX 3 Extra was impregnated with ferrous sulfate and used as catalyst (7 wt.% of iron). The effect of the main operating conditions in the Chicago Sky Blue (CSB) degradation was analyzed. It was found that the increase in temperature leads to a higher removal of the dye and an increased mineralization. However, it also increases the iron leaching, but the values observed were below 0.4 ppm (thus, far below European Union limits). It was possible to reach, at steady-state, a dye conversion of 88%, with a total organic carbon (TOC) removal of ca. 47%, being the reactor operated at 50 Degree-Sign C, pH 3, W{sub cat}/Q = 4.1 g min mL{sup -1} (W{sub cat} is the mass of catalyst and Q the total feed flow rate) and a H{sub 2}O{sub 2} feed concentration of 2.25 mM (for a CSB feed concentration of 0.012 mM). The same performance was reached in three consecutive cycles.

  10. Balanced Reed-Solomon codes for all parameters

    KAUST Repository

    Halbawi, Wael; Liu, Zihan; Hassibi, Babak

    2016-01-01

    We construct balanced and sparsest generator matrices for cyclic Reed-Solomon codes with any length n and dimension k. By sparsest, we mean that each row has the least possible number of nonzeros, while balanced means that the number of nonzeros in any two columns differs by at most one. Codes allowing such encoding schemes are useful in distributed settings where computational load-balancing is critical. The problem was first studied by Dau et al. who showed, using probabilistic arguments, that there always exists an MDS code over a sufficiently large field such that its generator matrix is both sparsest and balanced. Motivated by the need for an explicit construction with efficient decoding, the authors of the current paper showed that the generator matrix of a cyclic Reed-Solomon code of length n and dimension k can always be transformed to one that is both sparsest and balanced, when n and k are such that k/n (n-k+1) is an integer. In this paper, we lift this condition and construct balanced and sparsest generator matrices for cyclic Reed-Solomon codes for any set of parameters.

  11. Balanced Reed-Solomon codes for all parameters

    KAUST Repository

    Halbawi, Wael

    2016-10-27

    We construct balanced and sparsest generator matrices for cyclic Reed-Solomon codes with any length n and dimension k. By sparsest, we mean that each row has the least possible number of nonzeros, while balanced means that the number of nonzeros in any two columns differs by at most one. Codes allowing such encoding schemes are useful in distributed settings where computational load-balancing is critical. The problem was first studied by Dau et al. who showed, using probabilistic arguments, that there always exists an MDS code over a sufficiently large field such that its generator matrix is both sparsest and balanced. Motivated by the need for an explicit construction with efficient decoding, the authors of the current paper showed that the generator matrix of a cyclic Reed-Solomon code of length n and dimension k can always be transformed to one that is both sparsest and balanced, when n and k are such that k/n (n-k+1) is an integer. In this paper, we lift this condition and construct balanced and sparsest generator matrices for cyclic Reed-Solomon codes for any set of parameters.

  12. Spectral discrimination of giant reed (Arundo donax L.): A seasonal study in riparian areas

    Science.gov (United States)

    Fernandes, Maria Rosário; Aguiar, Francisca C.; Silva, João M. N.; Ferreira, Maria Teresa; Pereira, José M. C.

    2013-06-01

    The giant reed (Arundo donax L.) is amongst the one hundred worst invasive alien species of the world, and it is responsible for biodiversity loss and failure of ecosystem functions in riparian habitats. In this work, field spectroradiometry was used to assess the spectral separability of the giant reed from the adjacent vegetation and from the common reed, a native similar species. The study was conducted at different phenological periods and also for the giant reed stands regenerated after mechanical cutting (giant reed_RAC). A hierarchical procedure using Kruskal-Wallis test followed by Classification and Regression Trees (CART) was used to select the minimum number of optimal bands that discriminate the giant reed from the adjacent vegetation. A new approach was used to identify sets of wavelengths - wavezones - that maximize the spectral separability beyond the minimum number of optimal bands. Jeffries Matusita and Bhattacharya distance were used to evaluate the spectral separability using the minimum optimal bands and in three simulated satellite images, namely Landsat, IKONOS and SPOT. Giant reed was spectrally separable from the adjacent vegetation, both at the vegetative and the senescent period, exception made to the common reed at the vegetative period. The red edge region was repeatedly selected, although the visible region was also important to separate the giant reed from the herbaceous vegetation and the mid infrared region to the discrimination from the woody vegetation. The highest separability was obtained for the giant reed_RAC stands, due to its highly homogeneous, dense and dark-green stands. Results are discussed by relating the phenological, morphological and structural features of the giant reed stands and the adjacent vegetation with their optical traits. Weaknesses and strengths of the giant reed spectral discrimination are highlighted and implications of imagery selection for mapping purposes are argued based on present results.

  13. Pretreatment of Reed by Wet Oxidation and Subsequent Utilization of the Pretreated Fibers for Ethanol Production

    DEFF Research Database (Denmark)

    Szijarto, Nora; Kádár, Zsófia; Varga, Eniko

    2009-01-01

    lignocelluloses usually do. In the present study, wet oxidation was investigated as the pretreatment method to enhance the enzymatic digestibility of reed cellulose to soluble sugars and thus improve the convertibility of reed to ethanol. The most effective treatment increased the digestibility of reed cellulose...... of cellulose to glucose was 82.4%. Simultaneous saccharification and fermentation of pretreated solids resulted in a final ethanol concentration as high as 8.7 g/L, yielding 73% of the theoretical....

  14. Development library of finite elements for computer-aided design system of reed sensors

    Science.gov (United States)

    Kozlov, A. S.; Shmakov, N. A.; Tkalich, V. L.; Labkovskaia, R. I.; Kalinkina, M. E.; Pirozhnikova, O. I.

    2018-05-01

    The article is devoted to the development of a modern highly reliable element base of devices for security and fire alarm systems, in particular, to the improvement of the quality of contact cores (reed and membrane) of reed sensors. Modeling of elastic sensitive elements uses quadrangular elements of plates and shells, considered in the system of curvilinear orthogonal coordinates. The developed mathematical models and the formed finite element library are designed for systems of automated design of reed switch detectors to create competitive devices alarms. The finite element library is used for the automated system production of reed switch detectors both in series production and in the implementation of individual orders.

  15. Utilization of kura clover-reed canarygrass silage versus alfalfa silage by lactating dairy cows.

    Science.gov (United States)

    Kammes, K L; Heemink, G B H; Albrecht, K A; Combs, D K

    2008-08-01

    The mixture of kura clover (Trifolium ambiguum M. Bieb.) and reed canarygrass (Phalaris arundinacea L.) has proven to be extremely persistent in the northern United States, but information about dairy cow performance on this mixture is lacking. Twenty lactating Holstein cows were used in a crossover design to compare dry matter (DM) intake and milk production from diets containing kura clover-reed canarygrass silage (KRS) or alfalfa (Medicago sativa L.) silage (AS). Forages were cut, wilted, ensiled in horizontal plastic bags, and allowed to ferment for at least 50 d before beginning the feeding experiment. The KRS was approximately 40% kura clover and 60% reed canarygrass. Treatments were total mixed rations formulated with either 57% of total DM from 1) AS or 2) KRS. Experimental periods were 28 d, with the first 14 d for diet adaptation and the last 14 d for measurement of intake and milk production. The neutral detergent fiber (NDF) concentrations of AS and KRS were 37.3 and 47.3%, respectively. The fermentation analyses indicated that both silages underwent a restricted fermentation, producing primarily lactic acid and some acetic acid. Dry matter intake (24.2 vs. 22.8 kg) and 4% fat-corrected milk (32.8 vs. 30.9 kg) were significantly higher for cows fed AS than for cows fed KRS. Cows consumed less NDF (6.7 vs. 8.0 kg) and less digestible NDF (3.0 vs. 4.4 kg) when fed AS diets compared with KRS diets, but the pool of ruminally undegraded NDF was similar (3.7 kg) between diets. Cows produced 1.5 kg of milk/kg of DM consumed regardless of the diet, indicating that digestible NDF of KRS was utilized with similar efficiency as the cell wall constituents of AS, but the intake of cows fed KRS may have been limited by rumen fill. Milk fat concentration tended to be higher for cows fed AS, but the milk true protein concentration and yields of fat and protein did not differ by treatment. Milk urea nitrogen content was higher when cows consumed AS (16.4 mg/ d

  16. Environmental Assessment of Sewage Sludge Management – Focusing on Sludge Treatment Reed Bed Systems

    DEFF Research Database (Denmark)

    Larsen, Julie Dam

    profiles of the STRB system technology and a mechanical treatment technology, constituting a basis for decision-making in relation to choice of technology. A major part of the project involved performance of fieldwork and laboratory work. Data were collected at three Danish, well-operated STRB systems...... assessment were based on international acknowledged standards and recommendations. An attributional LCA approach was chosen, and the loadings and savings for all impact categories were normalised to people equivalents (PE) (the annual loadings and savings provided by one average person). Three sludge...... gasses CH4 and N2O were larger for mechanical dewatered sludge, the net environmental loadings provided to the impact category Climate Change by this technology (S-CEN) and the STRB system technology (S-STRB and S-SPA) ended up being equally sized (9.010-4 PE), despite of higher biological activity...

  17. Co-circulation of Usutu virus and West Nile virus in a reed bed ecosystem

    Czech Academy of Sciences Publication Activity Database

    Rudolf, Ivo; Bakonyi, T.; Šebesta, Oldřich; Mendel, Jan; Peško, Juraj; Betášová, Lenka; Blažejová, Hana; Venclíková, Kristýna; Straková, Petra; Nowotny, N.; Hubálek, Zdeněk

    2015-01-01

    Roč. 8, č. 520 (2015), s. 520 ISSN 1756-3305 EU Projects: European Commission(XE) 261504 - EDENEXT Institutional support: RVO:68081766 Keywords : Culex modestus * Usutu virus * West Nile virus * Flavivirus * Arbovirus * Surveillance * Mosquitoes Subject RIV: EE - Microbiology, Virology Impact factor: 3.234, year: 2015

  18. Evaluation of an up-flow anaerobic sludge bed (UASB) reactor containing diatomite and maifanite for the improved treatment of petroleum wastewater.

    Science.gov (United States)

    Chen, Chunmao; Liang, Jiahao; Yoza, Brandon A; Li, Qing X; Zhan, Yali; Wang, Qinghong

    2017-11-01

    Novel diatomite (R1) and maifanite (R2) were utilized as support materials in an up-flow anaerobic sludge bed (UASB) reactor for the treatment of recalcitrant petroleum wastewater. At high organic loadings (11kg-COD/m 3 ·d), these materials were efficient at reducing COD (92.7% and 93.0%) in comparison with controls (R0) (88.4%). Higher percentages of large granular sludge (0.6mm or larger) were observed for R1 (30.3%) and R2 (24.6%) compared with controls (22.6%). The larger portion of granular sludge provided a favorable habitat that resulted in greater microorganism diversity. Increased filamentous bacterial communities are believed to have promoted granular sludge formation promoting a conductive environment for stimulation methanogenic Archaea. These communities had enhanced pH tolerance and produced more methane. This study illustrates a new potential use of diatomite and maifanite as support materials in UASB reactors for increased efficiency when treating refractory wastewaters. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. The vibrating reed frequency meter : digital investigation of an early cochlear model

    NARCIS (Netherlands)

    Bell, Andrew; Wit, Hero P.

    2015-01-01

    The vibrating reed frequency meter, originally employed by Bekesy and later by Wilson as a cochlear model, uses a set of tuned reeds to represent the cochlea's graded bank of resonant elements and an elastic band threaded between them to provide nearest-neighbour coupling. Here the system,

  20. Islands in a desert : breeding ecology of the African Reed Warbler Acrocephalus baeticatus in Namibia

    NARCIS (Netherlands)

    Eising, CM; Komdeur, J; Buys, J; Reemer, M; Richardson, DS; Richardson, David S.

    The continental African Reed Warbler Acrocephalus baeticatus, like its relative the Seychelles Warbler Acrocephalus sechellensis, breeds in isolated patches. We studied the mating system of the African Reed Warbler to see whether this species, like the Seychelles Warbler, shows co-operative

  1. Ecosystem Service Value for the Common Reed Wetlands in the Liaohe Delta, Northeast China

    DEFF Research Database (Denmark)

    Ye, Siyuan; Laws, Edward A.; Costanza, Robert

    2016-01-01

    The largest reed field in the world, with an area of 1000 km2 in 1953, is located in the Liaohe Delta, which lies in the five-point-in-a-line economic strategic zone of northeastern China. However, the area of reeds has declined dramatically in recent years to accommodate oil field infrastructure...

  2. Hardware/Software Co-design Applied to Reed-Solomon Decoding for the DMB Standard

    NARCIS (Netherlands)

    Dam, A.C.; Lammertink, M.G.J.; Rovers, K.C.; Slagman, J.; Wellink, A.M.; Rauwerda, G.K.; Smit, Gerardus Johannes Maria

    2006-01-01

    This paper addresses the implementation of Reed- Solomon decoding for battery-powered wireless devices. The scope of this paper is constrained by the Digital Media Broadcasting (DMB). The most critical element of the Reed-Solomon algorithm is implemented on two different reconfigurable hardware

  3. Reed Reactor Facility annual report, September 1, 1994--August 31, 1995

    International Nuclear Information System (INIS)

    1995-01-01

    This report covers the period from September 1, 1994 to August 31, 1995. Information contained in this report is intended to fulfill several purposes including the reporting requirements of the US Nuclear Regulatory Commission (USNRC), the US Department of Energy (USDOE), and the Oregon Department of Energy (ODOE). Highlights of the last year include: (1) The number of new licensed student operators more than replaced the number of graduating seniors. Seven Reed College seniors used the reactor as part of their thesis projects. (2) The facility has been extraordinarily successful in obtaining donated equipment from Portland General Electric, US Department of Energy, Precision Castparts, Tektronix, and other sources. Battelle (Pacific Northwest Laboratory) has been generous in lending valuable equipment to the college. (3) The facility is developing more paid work. Income in the past academic year was much greater than the previous year, and next year should increase by even more. Additionally, the US Department of Energy's Reactor-Use Sharing grant increased significantly this year. During the year, the reactor was operated 225 separate times on 116 days. The total energy production was 24.6 MW-hours. The reactor staff consists of a Director, an Assistant Director, a contract Health Physicist, and approximately fifteen Reed College undergraduate students as hourly employees. All radiation exposures to individuals during this year were well below one percent of the federal limits. There were no releases of liquid radioactive material from the facility and airborne releases (primarily 41 Ar) were well within regulatory limits. No radioactive waste was shipped from the facility during this period

  4. Reed Reactor Facility annual report, September 1, 1994--August 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    This report covers the period from September 1, 1994 to August 31, 1995. Information contained in this report is intended to fulfill several purposes including the reporting requirements of the US Nuclear Regulatory Commission (USNRC), the US Department of Energy (USDOE), and the Oregon Department of Energy (ODOE). Highlights of the last year include: (1) The number of new licensed student operators more than replaced the number of graduating seniors. Seven Reed College seniors used the reactor as part of their thesis projects. (2) The facility has been extraordinarily successful in obtaining donated equipment from Portland General Electric, US Department of Energy, Precision Castparts, Tektronix, and other sources. Battelle (Pacific Northwest Laboratory) has been generous in lending valuable equipment to the college. (3) The facility is developing more paid work. Income in the past academic year was much greater than the previous year, and next year should increase by even more. Additionally, the US Department of Energy`s Reactor-Use Sharing grant increased significantly this year. During the year, the reactor was operated 225 separate times on 116 days. The total energy production was 24.6 MW-hours. The reactor staff consists of a Director, an Assistant Director, a contract Health Physicist, and approximately fifteen Reed College undergraduate students as hourly employees. All radiation exposures to individuals during this year were well below one percent of the federal limits. There were no releases of liquid radioactive material from the facility and airborne releases (primarily {sup 41}Ar) were well within regulatory limits. No radioactive waste was shipped from the facility during this period.

  5. Reed-Solomon Codes and the Deep Hole Problem

    Science.gov (United States)

    Keti, Matt

    In many types of modern communication, a message is transmitted over a noisy medium. When this is done, there is a chance that the message will be corrupted. An error-correcting code adds redundant information to the message which allows the receiver to detect and correct errors accrued during the transmission. We will study the famous Reed-Solomon code (found in QR codes, compact discs, deep space probes,ldots) and investigate the limits of its error-correcting capacity. It can be shown that understanding this is related to understanding the "deep hole" problem, which is a question of determining when a received message has, in a sense, incurred the worst possible corruption. We partially resolve this in its traditional context, when the code is based on the finite field F q or Fq*, as well as new contexts, when it is based on a subgroup of F q* or the image of a Dickson polynomial. This is a new and important problem that could give insight on the true error-correcting potential of the Reed-Solomon code.

  6. Bed agglomeration risk related to combustion of cultivated fuels (wheat straw, red canary grass, industrial hemp) in commercial bed materials; Baeddagglomereringsrisk vid foerbraenning av odlade braenslen (hampa, roerflen, halm) i kommersiella baeddmaterial

    Energy Technology Data Exchange (ETDEWEB)

    Erhardsson, Thomas; Oehman, Marcus; Geyter, Sigrid de; Oehrstroem, Anna

    2006-12-15

    The market of forest products is expanding and thus resulting in more expensive biomass fuels. Therefore research within the combustion industry for alternative fuels is needed, for example cultivated fuels. Combustion and gasification research on these cultivated fuels are limited. The objectives of this work was to increase the general knowledge of silicon rich cultivated fuels by study the agglomeration characteristics for wheat straw, reed canary grass and industrial hemp in combination with commercial bed materials. Controlled fluidized bed agglomeration tests was conducted in a 5 kW, bench-scale, bubbling fluidized bed reactor. The tendencies of agglomeration were determined with the three cultivated fuels in combination with various minerals present in natural sand (quarts, plagioclase and potassium feldspar) and an alternative bed material (olivine). During the experiments bed samples and formed agglomerates were collected for further analyses with a scanning electron microscope (SEM) and with X-ray microanalysis (EDS). Wheat straw had the highest agglomeration tendency of the studied fuels followed by reed canary grass and industrial hemp. No significant layer formation was found around the different bed particles. Instead, the ash forming matter were found as individual ash sticky (partial melted) particles in the bed. The bed material mineralogical composition had no influence of the agglomeration process because of the non layer formation propensities of the used silicon rich fuels.

  7. An exploration of common reed (Phragmites australis bioenergy potential in North America

    Directory of Open Access Journals (Sweden)

    R. Vaičekonytė

    2014-10-01

    Full Text Available In North America, reed (Phragmites australis is typically considered to be a weed although it provides important ecosystem services. Small, sparse, patchy or mixed reedbeds are more suitable as habitat for many species than extensive dense reedbeds, whose habitat functions can be enhanced by the selective removal of biomass. We propose that above-ground reed biomass could be harvested for bioenergy, at the same time improving habitat for biodiversity by thinning or fragmenting the more extensive reedbeds. Biofuel pellets manufactured from reeds harvested at Montréal (Canada had moisture content 6.4 %, energy content 16.9 kJ g-1 (dry mass, ash content 3.44 %, and chloride content 1962 ppm. Thus, reed as a material for fuel pellet manufacture is similar to switchgrass (Panicum virgatum, which is commonly cultivated for that purpose and requires higher inputs than harvested wild reed. We discuss these findings in the context of environmental considerations and conclude that the bioenergy potential of reed could most expediently be realised in North America by combining material harvested from the widespread spontaneously occurring reedbeds with organic waste from other sources to create mixed biofuels. However, reeds with high levels of chlorine, sulphur or metals should not be burned to avoid air pollution or equipment damage unless these problems are mitigated by means of appropriate season of harvest, equipment, combustion regime, or use of a mixed feedstock.

  8. Enzymatic Saccharification and Ethanol Fermentation of Reed Pretreated with Liquid Hot Water

    Directory of Open Access Journals (Sweden)

    Jie Lu

    2012-01-01

    Full Text Available Reed is a widespread-growing, inexpensive, and readily available lignocellulosic material source in northeast China. The objective of this study is to evaluate the liquid hot water (LHW pretreatment efficiency of reed based on the enzymatic digestibility and ethanol fermentability of water-insoluble solids (WISs from reed after the LHW pretreatment. Several variables in the LHW pretreatment and enzymatic hydrolysis process were optimized. The conversion of glucan to glucose and glucose concentrations are considered as response variables in different conditions. The optimum conditions for the LHW pretreatment of reed area temperature of 180°C for 20min and a solid-to-liquid ratio of 1 : 10. These optimum conditions for the LHW pretreatment of reed resulted in a cellulose conversion rate of 82.59% in the subsequent enzymatic hydrolysis at 50°C for 72 h with a cellulase loading of 30 filter paper unit per gram of oven-dried WIS. Increasing the pretreatment temperature resulted in a higher enzymatic digestibility of the WIS from reed. Separate hydrolysis and fermentation of WIS showed that the conversion of glucan to ethanol reached 99.5% of the theoretical yield. The LHW pretreatment of reed is a suitable method to acquire a high recovery of fermentable sugars and high ethanol conversion yield.

  9. A STUDY OF RECOVERING A REED ECOSYSTEM USING POROUS CONCRETE IN THE LAKE BIWA SHORE

    Science.gov (United States)

    Takeda, Naho; Kato, Hayato; Okamoto, Takahisa; Kojima, Takayuki

    In this study, reed planting tests were carried out at the Biyo-center, an experiment station on the Lake Biwa shore, in order to evaluate the feasibility of a planting method with porous concrete (PoC method). Reed planting tests with coconut-fiber mats (mat method), which were generally used around Lake Biwa, were simultaneously carried out to compare with the PoC method. The reeds planted by the PoC method grew better than the ones planted by the mat method, and the number of reeds which were washed away by waves was smaller than that planted by the mat method. The result of the observation of reeds planted in the PoC showed plant maturation, and reeds could ta ke root into the PoC without interference with the voids of the PoC. As a result, it was shown that the reed planting tests with the PoC method was simple and effective, so it would become in harmony with the environment around Lake Biwa.

  10. One-way quantum repeaters with quantum Reed-Solomon codes

    Science.gov (United States)

    Muralidharan, Sreraman; Zou, Chang-Ling; Li, Linshu; Jiang, Liang

    2018-05-01

    We show that quantum Reed-Solomon codes constructed from classical Reed-Solomon codes can approach the capacity on the quantum erasure channel of d -level systems for large dimension d . We study the performance of one-way quantum repeaters with these codes and obtain a significant improvement in key generation rate compared to previously investigated encoding schemes with quantum parity codes and quantum polynomial codes. We also compare the three generations of quantum repeaters using quantum Reed-Solomon codes and identify parameter regimes where each generation performs the best.

  11. Space communication system for compressed data with a concatenated Reed-Solomon-Viterbi coding channel

    Science.gov (United States)

    Rice, R. F.; Hilbert, E. E. (Inventor)

    1976-01-01

    A space communication system incorporating a concatenated Reed Solomon Viterbi coding channel is discussed for transmitting compressed and uncompressed data from a spacecraft to a data processing center on Earth. Imaging (and other) data are first compressed into source blocks which are then coded by a Reed Solomon coder and interleaver, followed by a convolutional encoder. The received data is first decoded by a Viterbi decoder, followed by a Reed Solomon decoder and deinterleaver. The output of the latter is then decompressed, based on the compression criteria used in compressing the data in the spacecraft. The decompressed data is processed to reconstruct an approximation of the original data-producing condition or images.

  12. Torsion testing of bed joints

    DEFF Research Database (Denmark)

    Hansen, Klavs Feilberg; Pedersen, Carsten Mørk

    2008-01-01

    This paper describes a simple test method for determining the torsion strength of a single bed joint between two bricks and presents results from testing using this test method. The setup for the torsion test is well defined, require minimal preparation of the test specimen and the test can...... be carried out directly in a normal testing machine. The torsion strength is believed to be the most important parameter in out-of-plane resistance of masonry walls subjected to bending about an axis perpendicular to the bed joints. The paper also contains a few test results from bending of small walls about...... an axis perpendicular to the bed joints, which indicate the close connection between these results and results from torsion tests. These characteristics make the torsion strength well suited to act as substitute parameter for the bending strength of masonry about an axis perpendicular to the bed joints....

  13. Effect of Additives and Fuel Blending on Emissions and Ash-Related Problems from Small-Scale Combustion of Reed Canary Grass

    Directory of Open Access Journals (Sweden)

    Sébastien Fournel

    2015-07-01

    Full Text Available Agricultural producers are interested in using biomass available on farms to substitute fossil fuels for heat production. However, energy crops like reed canary grass contain high nitrogen (N, sulfur (S, potassium (K and other ash-forming elements which lead to increased emissions of gases and particulate matter (PM and ash-related operational problems (e.g., melting during combustion. To address these problematic behaviors, reed canary grass was blended with wood (50 wt% and fuel additives (3 wt% such as aluminum silicates (sewage sludge, calcium (limestone and sulfur (lignosulfonate based additives. When burned in a top-feed pellet boiler (29 kW, the four blends resulted in a 17%–29% decrease of PM concentrations compared to pure reed canary grass probably because of a reduction of K release to flue gas. Nitrogen oxides (NOx and sulfur dioxide (SO2 emissions varied according to fuel N and S contents. This explains the lower NOx and SO2 levels obtained with wood based products and the higher SO2 generation with the grass/lignosulfonate blend. The proportion of clinkers found in combustion ash was greatly lessened (27%–98% with the use of additives, except for lignosulfonate. The positive effects of some additives may allow agricultural fuels to become viable alternatives.

  14. On locality of Generalized Reed-Muller codes over the broadcast erasure channel

    KAUST Repository

    Alloum, Amira; Lin, Sian Jheng; Al-Naffouri, Tareq Y.

    2016-01-01

    , and more specifically at the application layer where Rateless, LDPC, Reed Slomon codes and network coding schemes have been extensively studied, optimized and standardized in the past. Beyond reusing, extending or adapting existing application layer packet

  15. Ishmael Reed and the Politics of Aesthetics, or Shake Hands and Come Out Conjuring

    Science.gov (United States)

    Fontenot, Chester J.

    1978-01-01

    Discusses the ways in which Ishmael Reed uses black American folklore, black American language, traditional African religion, and African myths as poetic materials from which he develops artistic forms. (GW)

  16. Arrangement of permanent magnet and reed switches for control rod position indicator of SMART CEDM

    International Nuclear Information System (INIS)

    Yoo, J. Y.; Kim, J. I.; Kim, J. H.; Hur, H.; Jang, M. H.

    2001-01-01

    The reliability and accuracy of the information on control rod position are very important to the reactor safety and the design of the core protection system. A survey on the RSPT(Reed Switch Position Transmitter) type control rod position indication system and its actual implementation in the exiting nuclear power plants in Korea was performed first. The control rod position indicator having the high performance for SMART was developed on the basis of RSPT technology identified through the survey. The arrangement of permanent magnet and reed switches is the most important procedure in the design of control rod position indication. In this study, the characteristics of permanent magnet and reed switches are introduced and the calculation method for arrangement of permanent magnet and reed switch is presented

  17. Paraskeva pühastest ja reede kultusest Satserinna kiriklikus traditsioonis / Kai Kuusing

    Index Scriptorium Estoniae

    Kuusing, Kai

    2005-01-01

    Saatse kirikust pärit Paraskeva pühaste (ikoonide) ikonograafia- ja hagiograafiaalasest materjalist ning Paraskeva kultusega seotud kahest erinevast traditsioonist Saatse kirikus - Ikonioni Paraskeva mälestuspäeva ja Eelija reede pühitsemisest

  18. Attempts on cardoon gasification in two different circulating fluidized beds

    Directory of Open Access Journals (Sweden)

    Chr. Christodoulou

    2014-11-01

    Full Text Available Few tests have been carried out in order to evaluate the use of cardoon in gasification and combustion applications most of the researchers dealt with agglomeration problems. The aim of this work is to deal with the agglomeration problem and to present a solution for the utilization of this biofuel at a near industrial application scale. For this reason, two experiments were conducted, one in TU Delft and one in Centre for Research and Technology Hellas (CERTH, using fuel cardoon and 50% w/w cardoon blended with 50% w/w giant reed respectively. Both experimental campaigns were carried out in similar atmospheric circulating fluidized bed gasifiers. Apart from the feedstock, the other differences were the gasification medium and the bed material used in each trial. The oxidizing agent at TUD׳s run was O2/steam, whereas CERTH׳s tests used air. When experiments with the cardoon 50% w/w–giant reed 50% w/w blend were performed no agglomeration problems were presented. Consequently, gasification could be achieved in higher temperature than that of pure cardoon which led to the reduction of tar concentration.

  19. Creation of Principally New Generation of Switching Technique Elements (Reed Switches) with Nanostructured Contact Surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Karabanov S M; Zeltser I A; Maizels R M; Moos E N; Arushanov K A, E-mail: zeltseria@rmcip.ru [Russia, Ryazan, 390027, Novaya Str., 51B, Ryazan Metal Ceramics Instrumentation Plant JSC (Russian Federation)

    2011-04-01

    The cycle of activities of the creation of principally new generation of reed switches with nanostructured contact surfaces was implemented. Experimental justification of the opportunity of reed switches creation with modified contact surface was given (instead of precious metals-based galvanic coating). Principally new technological process of modification of magnetically operated contacts contacting surfaces was developed, based on the usage of the ion-plasma methods of nanolayers and nanostructures forming having specified contact features.

  20. In vitro incorporation of tritiated thymidine by the Sternberg-Reed cells in Hodgkin disease

    Energy Technology Data Exchange (ETDEWEB)

    Marinello, M; Tkachenko, G; Gavilondo, J; Baeza, B [National Institute of Oncology and Radiology, Havana (Cuba)

    1975-01-01

    A new DNA synthesis by the Sternberg-Reed cells in Hodgkin disease was studied using tritiated thymidine and autoradiography. The results show that after incubation pulses of 30 and 60 minutes, cells with lobulated nucleus, binucleated and trinucleated cells identifiable to the diagnostic Sternberg-Reed cells could undergo a new DNA synthesis. This points to a more dynamic interpretation of this type of cell.

  1. Reed-Solomon error-correction as a software patch mechanism.

    Energy Technology Data Exchange (ETDEWEB)

    Pendley, Kevin D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2013-11-01

    This report explores how error-correction data generated by a Reed-Solomon code may be used as a mechanism to apply changes to an existing installed codebase. Using the Reed-Solomon code to generate error-correction data for a changed or updated codebase will allow the error-correction data to be applied to an existing codebase to both validate and introduce changes or updates from some upstream source to the existing installed codebase.

  2. An experimental study on coolability of a particulate bed with radial stratification or triangular shape

    International Nuclear Information System (INIS)

    Thakre, Sachin; Li, Liangxing; Ma, Weimin

    2014-01-01

    Highlights: • Dryout heat flux of a particulate bed with radial stratification is obtained. • It was found to be dominated by hydrodynamics in the bigger size of particle layer. • Coolability of a particulate bed with triangular shape is investigated. • The coolability is improved in the triangular bed due to lateral ingression of coolant. • Coolability of both beds is enhanced by a downcomer. - Abstract: This paper deals with the results of an experimental study on the coolability of particulate beds with radial stratification and triangular shape, respectively. The study is intended to get an idea on how the coolability is affected by the different features of a debris bed formed in a severe accident of light water reactors. The experiments were performed on the POMECO-HT facility which was constructed to investigate two-phase flow and heat transfer in particulate beds under either top-flooding or bottom-fed condition. A downcomer is designed to enable investigation of the effectiveness of natural circulation driven coolability. Two homogenous beds were also employed in the present study to compare their dryout power densities with those of the radially stratified bed and the triangular bed. The results show that the dryout heat fluxes of the homogeneous beds at top-flooding condition can be predicted by the Reed model. For the radially stratified bed, the dryout heat flux is dominated by two-phase flow in the columns packed with larger particles, and the dryout occurred initially near the boundary between the middle column and a side column. Given the same volume of particles under top-flooding condition, the dryout power density of the triangular bed is about 69% higher than that of the homogenous bed. The coolability of all the beds is enhanced by bottom-fed coolant driven by either forced injection or downcomer-induced natural circulation

  3. An experimental study on coolability of a particulate bed with radial stratification or triangular shape

    Energy Technology Data Exchange (ETDEWEB)

    Thakre, Sachin; Li, Liangxing; Ma, Weimin, E-mail: ma@safety.sci.kth.se

    2014-09-15

    Highlights: • Dryout heat flux of a particulate bed with radial stratification is obtained. • It was found to be dominated by hydrodynamics in the bigger size of particle layer. • Coolability of a particulate bed with triangular shape is investigated. • The coolability is improved in the triangular bed due to lateral ingression of coolant. • Coolability of both beds is enhanced by a downcomer. - Abstract: This paper deals with the results of an experimental study on the coolability of particulate beds with radial stratification and triangular shape, respectively. The study is intended to get an idea on how the coolability is affected by the different features of a debris bed formed in a severe accident of light water reactors. The experiments were performed on the POMECO-HT facility which was constructed to investigate two-phase flow and heat transfer in particulate beds under either top-flooding or bottom-fed condition. A downcomer is designed to enable investigation of the effectiveness of natural circulation driven coolability. Two homogenous beds were also employed in the present study to compare their dryout power densities with those of the radially stratified bed and the triangular bed. The results show that the dryout heat fluxes of the homogeneous beds at top-flooding condition can be predicted by the Reed model. For the radially stratified bed, the dryout heat flux is dominated by two-phase flow in the columns packed with larger particles, and the dryout occurred initially near the boundary between the middle column and a side column. Given the same volume of particles under top-flooding condition, the dryout power density of the triangular bed is about 69% higher than that of the homogenous bed. The coolability of all the beds is enhanced by bottom-fed coolant driven by either forced injection or downcomer-induced natural circulation.

  4. Engine Cycle Analysis of Air Breathing Microwave Rocket with Reed Valves

    International Nuclear Information System (INIS)

    Fukunari, Masafumi; Komatsu, Reiji; Yamaguchi, Toshikazu; Komurasaki, Kimiya; Arakawa, Yoshihiro; Katsurayama, Hiroshi

    2011-01-01

    The Microwave Rocket is a candidate for a low cost launcher system. Pulsed plasma generated by a high power millimeter wave beam drives a blast wave, and a vehicle acquires impulsive thrust by exhausting the blast wave. The thrust generation process of the Microwave Rocket is similar to a pulse detonation engine. In order to enhance the performance of its air refreshment, the air-breathing mechanism using reed valves is under development. Ambient air is taken to the thruster through reed valves. Reed valves are closed while the inside pressure is high enough. After the time when the shock wave exhausts at the open end, an expansion wave is driven and propagates to the thrust-wall. The reed valve is opened by the negative gauge pressure induced by the expansion wave and its reflection wave. In these processes, the pressure oscillation is important parameter. In this paper, the pressure oscillation in the thruster was calculated by CFD combined with the flux through from reed valves, which is estimated analytically. As a result, the air-breathing performance is evaluated using Partial Filling Rate (PFR), the ratio of thruster length to diameter L/D, and ratio of opening area of reed valves to superficial area α. An engine cycle and predicted thrust was explained.

  5. Integrated non-food concept of rape seed, reed canary grass and flax processing for fiber, fuel oil and solid fuel

    International Nuclear Information System (INIS)

    Sipilae, K.

    1998-01-01

    The target of the project was to investigate if rape seed based fuel oil and diesel fuel component, agrofiber and solid fuel from other annual crops could be produced effectively as an alternative to existing non-economical biodiesel-RME and ethanol production. Without heavy tax incentives the biodiesel and grain ethanol can not compete with conventional liquid fuels, the present EU fuel tax legislation will not permit any permanent tax incentives for commercial scale operations. Based on several studies by VTT the rape seed oil will be 30 % cheaper than RME and the utilization as a component 10-30 % blended to heating oil or diesel fuel might the most flexible solution. Neste Oy has carried out the combustion tests with 20 kW boiler and VTT the diesel engine tests with 20 % unprocessed rape seed oil mixtures, the oil was delivered by Mildola Oy. For the co-utilization of annual crops and straw, several laboratory scale combustion and flash pyrolysis tests have been carried out by VTT with straw, reed canary grass etc. In fluid bed combustion 10-30 % addition of rape seed straw and reed canary grass, which have high ash melting point, seems to be less problematic compared to other straw species, which are used for example in Denmark. In a flash pyrolysis process, the alkalies will remain in the char and a low alkali level bio oils can be produced. As a final step in order to reach the zero subsidy target, an extensive laboratory work is carried out to produce agro fibre from flax, reed canary grass and wheat straw. The laboratory results show that a good quality pulp can be produced to be mixed with conventional wood fibres, the quality of flax pulp is even better compared to conventional pulp. During the next months an overall economic calculations will be carried out in Finnish, Danish and Italian conditions as an EU-Apas project in order to see the competitiveness of such integrated concepts to conventional RME and reed canary grass combustion. (orig.)

  6. Fluidized-bed nuclear reactor

    International Nuclear Information System (INIS)

    Grimmett, E.S.; Kunze, J.F.

    1975-01-01

    A reactor vessel containing a fluidized-bed region of particulate material including both a neutron-moderating and a fertile substance is described. A gas flow including fissile material passes through the vessel at a sufficient rate to fluidize the particulate material and at a sufficient density to support a thermal fission reaction within the fluidized-bed region. The high-temperature portion of a heat transfer system is located within the fluidized-bed region of the reactor vessel in direct contact with the fluidized particles. Heat released by fission is thereby transferred at an enhanced rate to a coolant circulating within the heat transfer system. Fission products are continuously removed from the gas flow and supplemental fissile material added during the reactor operation. (U.S.)

  7. Fluidized bed heat exchanger utilizing angularly extending heat exchange tubes

    Science.gov (United States)

    Talmud, Fred M.; Garcia-Mallol, Juan-Antonio

    1980-01-01

    A fluidized bed heat exchanger in which air is passed through a bed of particulate material containing fuel disposed in a housing. A steam/water natural circulation system is provided and includes a steam drum disposed adjacent the fluidized bed and a series of tubes connected at one end to the steam drum. A portion of the tubes are connected to a water drum and in the path of the air and the gaseous products of combustion exiting from the bed. Another portion of the tubes pass through the bed and extend at an angle to the upper surface of the bed.

  8. Internal dust recirculation system for a fluidized bed heat exchanger

    Science.gov (United States)

    Gamble, Robert L.; Garcia-Mallol, Juan A.

    1981-01-01

    A fluidized bed heat exchanger in which air is passed through a bed of particulate material containing fuel disposed in a housing. A steam/water natural circulation system is provided in a heat exchange relation to the bed and includes a steam drum disposed adjacent the bed and a tube bank extending between the steam drum and a water drum. The tube bank is located in the path of the effluent gases exiting from the bed and a baffle system is provided to separate the solid particulate matter from the effluent gases. The particulate matter is collected and injected back into the fluidized bed.

  9. Classification and Monitoring of Reed Belts Using Dual-Polarimetric TerraSAR-X Time Series

    Directory of Open Access Journals (Sweden)

    Iris Heine

    2016-06-01

    Full Text Available Synthetic aperture radar polarimetry (PolSAR and polarimetric decomposition techniques have proven to be useful tools for wetland mapping. In this study we classify reed belts and monitor their phenological changes at a natural lake in northeastern Germany using dual-co-polarized (HH, VV TerraSAR-X time series. The time series comprises 19 images, acquired between August 2014 and May 2015, in ascending and descending orbit. We calculated different polarimetric indices using the HH and VV intensities, the dual-polarimetric coherency matrix including dominant and mean alpha scattering angles, and entropy and anisotropy (normalized eigenvalue difference as well as combinations of entropy and anisotropy for the analysis of the scattering scenarios. The image classifications were performed with the random forest classifier and validated with high-resolution digital orthophotos. The time series analysis of the reed belts revealed significant seasonal changes for the double-bounce–sensitive parameters (intensity ratio HH/VV and intensity difference HH-VV, the co-polarimetric coherence phase and the dominant and mean alpha scattering angles and in the dual-polarimetric coherence (amplitude, anisotropy, entropy, and anisotropy-entropy combinations; whereas in summer dense leaves cause volume scattering, in winter, after leaves have fallen, the reed stems cause predominately double-bounce scattering. Our study showed that the five most important parameters for the classification of reed are the intensity difference HH-VV, the mean alpha scattering angle, intensity ratio HH/VV, and the coherence (phase. Due to the better separation of reed and other vegetation (deciduous forest, coniferous forest, meadow, winter acquisitions are preferred for the mapping of reed. Multi-temporal stacks of winter images performed better than summer ones. The combination of ascending and descending images also improved the result as it reduces the influence of the sensor

  10. Resistance strategies of Phragmites australis (common reed to Pb pollution in flood and drought conditions

    Directory of Open Access Journals (Sweden)

    Na Zhang

    2018-01-01

    Full Text Available Resistance strategies of clonal organs, and parent and offspring shoots of Phragmites australis (common reed to heavy metal pollution in soils are not well known. To clarify the tolerance or resistance strategies in reeds, we conducted a pot experiment with five levels of Pb concentration (0∼4,500 mg kg−1 in flood and drought conditions. Lead toxicity had no inhibitory effect on the number of offspring shoots in flood environment; however, biomass accumulation, and photosynthetic and clonal growth parameters were inhibited in both water environment. At each treatment of Pb concentration, offspring shoots had greater biomass and higher photosynthesis indicators than parent shoots. The lowest Pb allocation was found in rhizomes. More of the Pb transported to above-ground parts tended to accumulate in parent shoots rather than in offspring shoots. Biomass and photosynthesis of offspring shoots, rhizome length, and the number of buds, rhizomes and offspring shoots in the flooded treatment were significantly greater than those in the drought treatment. Our results indicated that the tolerance strategies used by reeds, including higher biomass accumulation and photosynthesis in offspring shoots, low allocation of Pb in rhizomes and offspring shoots, and stable clonal growth, maintained the stability of population propagation and productivity, improving the resistance of reeds to Pb pollution in flood environment. However, the resistance or tolerance was significantly reduced by the synergistic effect of Pb and drought, which significantly inhibited biomass accumulation, photosynthesis, and clonal growth of reeds.

  11. Noncontact modal analysis of a pipe organ reed using airborne ultrasound stimulated vibrometry

    Science.gov (United States)

    Huber, Thomas M.; Fatemi, Mostafa; Kinnick, Randall R.; Greenleaf, James F.

    2004-05-01

    The goal of this experiment was to excite and measure, in a noncontact manner, the vibrational modes of the reed from a reed organ pipe. To perform ultrasound stimulated excitation, two ultrasound beams in air of different frequencies were directed at the reed; the audio-range beat frequency between these ultrasound beams induced vibrations. The resulting vibrational deflection shapes were measured with a scanning vibrometer. The modes of any relatively small object can be studied in air using this technique. For a 36 mm by 7 mm clamped brass reed cantilever, displacements and velocites of 5 μ and 4 mm/s could be imparted at the fundamental frequency of 145 Hz. Using the same ultrasound transducer, excitation across the entire range of audio frequencies was obtained, which was not possible using audio excitation with a speaker. Since the beam was focused on the reed, ultrasound stimulated excitation eliminated background effects observed during mechanical shaker excitation, such as vibrations of clamps and supports. We will discuss the results obtained using single, dual, and confocal ultrasound transducers in AM and unmodulated CW modes, along with results obtained using a mechanical shaker and audio excitation using a speaker.

  12. NRC [Nuclear Regulatory Commission] staff evaluation of the General Electric Company Nuclear Reactor Study (''Reed Report'')

    International Nuclear Information System (INIS)

    1987-07-01

    In 1975, the General Electric Company (GE) published a Nuclear Reactor Study, also referred to as ''the Reed Report,'' an internal product-improvement study. GE considered the document ''proprietary'' and thus, under the regulations of the Nuclear Regulatory Commission (NRC), exempt from mandatory public disclosure. Nonetheless, members of the NRC staff reviewed the document in 1976 and determined that it did not raise any significant new safety issues. The staff also reached the same conclusion in subsequent reviews. However, in response to recent inquiries about the report, the staff reevaluated the Reed Report from a 1987 perspective. This re-evaluation, documented in this staff report, concluded that: (1) there are no issues raised in the Reed Report that support a need to curtail the operation of any GE boiling water reactor (BWR); (2) there are no new safety issues raised in the Reed Report of which the staff was unaware; and (3) although certain issues addressed by the Reed Report are still being studied by the NRC and the industry, there is no basis for suspending licensing and operation of GE BWR plants while these issues are being resolved

  13. Ammonia Fiber Expansion Pretreatment and Enzymatic Hydrolysis on Two Different Growth Stages of Reed Canarygrass

    Science.gov (United States)

    Bradshaw, Tamika C.; Alizadeh, Hasan; Teymouri, Farzaneh; Balan, Venkatesh; Dale, Bruce E.

    Plant materials from the vegetative growth stage of reed canarygrass and the seed stage of reed canarygrass are pretreated by ammonia fiber expansion (AFEX) and enzymatically hydrolyzed using 15 filter paper units (FPU) cellulase/g glucan to evaluate glucose and xylose yields. Percent conversions of glucose and xylose, effects of temperature and ammonia loading, and hydrolysis profiles are analyzed to determine the most effective AFEX treatment condition for each of the selected materials. The controls used in this study were untreated samples of each biomass material. All pretreatment conditions tested enhanced enzyme digestibility and improved sugar conversions for reed canarygrass compared with their untreated counterparts. Based on 168 h hydrolysis results using 15 FPU Spezyme CP cellulase/g glucan the most effective AFEX treatment conditions were determined as: vegetative growth stage of reed canarygrass—100°C, 60% moisture content, 1.2∶1 kg ammonia/kg of dry matter (86% glucose and 78% xylose) and seed stage of reed canarygrass—100°C, 60% moisture content, 0.8∶1 kg ammonia/kg of dry matter (89% glucose and 81% xylose). Supplementation by commercial Multifect 720 xylanase along with cellulase further increased both glucose and xylose yields by 10-12% at the most effective AFEX conditions.

  14. Practice Hospital Bed Safety

    Science.gov (United States)

    ... Home For Consumers Consumer Updates Practice Hospital Bed Safety Share Tweet Linkedin Pin it More sharing options ... It depends on the complexity of the bed." Safety Tips CDRH offers the following safety tips for ...

  15. Bed Bugs and Schools

    Science.gov (United States)

    Bed bugs have long been a pest – feeding on blood, causing itchy bites and generally irritating their human hosts. They are successful hitchhikers, and can move from an infested site to furniture, bedding, baggage, boxes, and clothing.

  16. A study on flow distribution for integrated hybrid actuator by analysis of reed valve

    Energy Technology Data Exchange (ETDEWEB)

    Woo, Jang Mi; Kang, Seung Hwan; Ko, Han Seo [Sungkyunkwan University, Suwon (Korea, Republic of); Goo, Nam Seo; Li, Yong Zhe [Konkuk University, Seoul (Korea, Republic of)

    2016-05-15

    Many studies have been conducted recently on an integrated hybrid actuator due to the increasing need for unmanned aircraft and guided weapons. In this study, flow distribution was analyzed for a reed valve which was used for flow regulation to improve the performance of the actuator. By using a Fluid structural interaction (FSI) technique with Computational fluid dynamics (CFD) having a moving mesh, numerical analysis was performed according to the thickness, shape and driving frequency of the reed valve. From the calculated results, the maximum performance of the reed valve was found at the valve thickness of 0.15 mm and the driving frequency of 250 Hz for a no-load state. The optimum thickness and shape for the valve for each driving frequency were also realized.

  17. The mechanical spectra of deposited materials by a composite reed vibration method

    International Nuclear Information System (INIS)

    Ying, X.N.; Zhang, L.; Yuan, Y.H.

    2010-01-01

    Recently a composite reed vibration method has been designed to measure the mechanical spectra (complex Young's modulus) of materials from liquid to solid state. The mechanical spectra of materials can be obtained from a composite system consisting of a substrate reed and of materials deposited on it. In this report, two sets of formulas to calculate the mechanical spectra of deposited materials are further analyzed. The proof is given for the previous named 'approximate formulas' (labeled as Formula II). Then the composite reed vibration method can be safely used as an extension of the mechanical spectrum method of the thin solid film. At the same time, some comments are made on previous analytical formulas (labeled as Formula I). At last, more experiments with a small amount of deposited materials are performed. It is found that smaller quantity is more favorable to achieve the intrinsic mechanical spectra of deposited materials.

  18. Using aerial photography for mapping giant reed infestations along the Texas-Mexico portion of the Rio Grande.

    Science.gov (United States)

    Giant reed (Arundo donax L.) is an invasive weed throughout the southern half of the United States with the densest stands growing along the coastal rivers of southern California and the Rio Grande in Texas. The objective of this study was to use aerial photography to map giant reed infestations and...

  19. Mapping giant reed (Arundo donax) infestations along the Texas-Mexico portion of the Rio Grande using aerial photography

    Science.gov (United States)

    Giant reed is an invasive weed throughout the southern half of the United States with the densest stands growing along the coastal rivers of southern California and the Rio Grande in Texas. The objective of this study was to use aerial photography to map giant reed infestations and estimate infested...

  20. Continuous fermentation and in-situ reed separation of butyric acid for higher sugar consumption rate and productivity

    DEFF Research Database (Denmark)

    Baroi, George Nabin; Skiadas, Ioannis; Westermann, Peter

    that disconnection of the REED system resulted to much lower (48 and 83% for glucose and xylose, respectively) sugars consumption rates and consequently lower butyric acid production rates. It was also noticeable that continuous operation, even without the REED system, resulted to higher glucose consumption rates...

  1. 77 FR 19362 - Environmental Assessment and Finding of No Significant Impact for License Renewal for the Reed...

    Science.gov (United States)

    2012-03-30

    ... serves about 1,300 students. The Reed Research Reactor is housed in a section of the Psychology Building constructed specifically for that purpose. The section of the Psychology building housing the Reed Research... encompasses the entire Psychology Building and all areas 76 meters (250 feet) from the center of the reactor...

  2. Pacemaker reed switch behavior in 0.5, 1.5, and 3.0 Tesla magnetic resonance imaging units: are reed switches always closed in strong magnetic fields?

    Science.gov (United States)

    Luechinger, Roger; Duru, Firat; Zeijlemaker, Volkert A; Scheidegger, Markus B; Boesiger, Peter; Candinas, Reto

    2002-10-01

    MRI is established as an important diagnostic tool in medicine. However, the presence of a cardiac pacemaker is usually regarded as a contraindication for MRI due to safety reasons. The aim of this study was to investigate the state of a pacemaker reed switch in different orientations and positions in the main magnetic field of 0.5-, 1.5-, and 3.0-T MRI scanners. Reed switches used in current pacemakers and ICDs were tested in 0.5-, 1.5-, and 3.0-T MRI scanners. The closure of isolated reed switches was evaluated for different orientations and positions relative to the main magnetic field. The field strengths to close and open the reed switch and the orientation dependency of the closed state inside the main magnetic field were investigated. The measurements were repeated using two intact pacemakers to evaluate the potential influence of the other magnetic components, like the battery. If the reed switches were oriented parallel to the magnetic fields, they closed at 1.0 +/- 0.2 mT and opened at 0.7 +/- 0.2 mT. Two different reed switch behaviors were observed at different magnetic field strengths. In low magnetic fields ( 200 mT), the reed switches opened in 50% of all tested orientations. No difference between the three scanners could be demonstrated. The reed switches showed the same behavior whether they were isolated or an integral part of the pacemakers. The reed switch in a pacemaker or an ICD does not necessarily remain closed in strong magnetic fields at 0.5, 1.5, or 3.0 T and the state of the reed switch may not be predictable with certainty in clinical situations.

  3. Host plant development, water level and water parameters shape Phragmites australis-associated oomycete communities and determine reed pathogen dynamics in a large lake.

    Science.gov (United States)

    Wielgoss, Anna; Nechwatal, Jan; Bogs, Carolin; Mendgen, Kurt

    2009-08-01

    In a 3-year-study, we analysed the population dynamics of the reed pathogen Pythium phragmitis and other reed-associated oomycetes colonizing fresh and dried reed leaves in the littoral zone of a large lake. Oomycete communities derived from internal transcribed spacer clone libraries were clearly differentiated according to substrate and seasonal influences. In fresh leaves, diverse communities consisting of P. phragmitis and other reed-associated pathogens were generally dominant. Pythium phragmitis populations peaked in spring with the emergence of young reed shoots, and in autumn after extreme flooding events. In summer it decreased with falling water levels, changing water chemistry and rising temperatures. Another Pythium species was also highly abundant in fresh leaves throughout the year and might represent a new, as-yet uncultured reed pathogen. In dried leaves, reed pathogens were rarely detected, whereas saprophytic species occurred abundantly during all seasons. Saprophyte communities were less diverse, less temperature sensitive and independent of reed development. In general, our results provide evidence for the occurrence of highly specialized sets of reed-associated oomycetes in a natural reed ecosystem. Quantitative analyses (clone abundances and quantitative real-time PCR) revealed that the reed pathogen P. phragmitis is particularly affected by changing water levels, water chemistry and the stage of reed development.

  4. Die-back of Phragmites australis in European wetlands: an overview of the European Research Programme on Reed Die-Back and Progression (1993-1994)

    NARCIS (Netherlands)

    Van der Putten, W.H.

    1997-01-01

    Reed (Phragmites australis (Cav.) Trin. ex Steudel) is one of the dominant plant species in European land-water ecotones. During the past decades reed belts have died back, especially in central and eastern Europe. The aim of the European Research Programme on Reed Die-back and Progression (EUREED),

  5. Fluid-Structure Interaction of a Reed Type Valve Subjected to Piston Displacement

    OpenAIRE

    Estruch, Olga; Lehmkuhl, Oriol; Rigola, Joaquim; Pérez-Segarra, Carles David

    2014-01-01

    In the field of reciprocating compressors, the developing of reed type valves is a challenging task. The understanding of the fluid flow behaviour through the valve reed is essential to improve the valve design. Hence, this work attempts the dynamic simulation of this fluid-structure interaction (FSI) problem, taking into account valve movement due to piston displacement. In this work attends the in-house implemented CFD&HT and moving mesh coupled code TermoFluids [1]. The CFD&HT solver consi...

  6. The fast decoding of Reed-Solomon codes using high-radix fermat theoretic transforms

    Science.gov (United States)

    Liu, K. Y.; Reed, I. S.; Truong, T. K.

    1976-01-01

    Fourier-like transforms over GF(F sub n), where F sub n = 2(2n) + 1 is a Fermat prime, are applied in decoding Reed-Solomon codes. It is shown that such transforms can be computed using high-radix fast Fourier transform (FFT) algorithms requiring considerably fewer multiplications than the more usual radix 2 FFT algorithm. A special 256-symbol, 16-symbol-error-correcting, Reed-Solomon (RS) code for space communication-link applications can be encoded and decoded using this high-radix FFT algorithm over GF(F sub 3).

  7. Differences in breeding bird assemblages related to reed canary grass cover cover and forest structure on the Upper Mississippi River

    Science.gov (United States)

    Kirsch, Eileen M.; Gray, Brian R.

    2017-01-01

    Floodplain forest of the Upper Mississippi River provides habitat for an abundant and diverse breeding bird community. However, reed canary grass Phalaris arundinacea invasion is a serious threat to the future condition of this forest. Reed canary grass is a well-known aggressive invader of wetland systems in the northern tier states of the conterminous United States. Aided by altered flow regimes and nutrient inputs from agriculture, reed canary grass has formed dense stands in canopy gaps and forest edges, retarding tree regeneration. We sampled vegetation and breeding birds in Upper Mississippi River floodplain forest edge and interior areas to 1) measure reed canary grass cover and 2) evaluate whether the breeding bird assemblage responded to differences in reed canary grass cover. Reed canary grass was found far into forest interiors, and its cover was similar between interior and edge sites. Bird assemblages differed between areas with more or less reed canary grass cover (.53% cover breakpoint). Common yellowthroat Geothlypis trichas, black-capped chickadee Parus atricapillus, and rose-breasted grosbeak Pheucticus ludovicianus were more common and American redstart Setophaga ruticilla, great crested flycatcher Myiarchus crinitus, and Baltimore oriole Icterus galbula were less common in sites with more reed canary grass cover. Bird diversity and abundance were similar between sites with different reed canary grass cover. A stronger divergence in bird assemblages was associated with ground cover ,15%, resulting from prolonged spring flooding. These sites hosted more prothonotary warbler Protonotaria citrea, but they had reduced bird abundance and diversity compared to other sites. Our results indicate that frequently flooded sites may be important for prothonotary warblers and that bird assemblages shift in response to reed canary grass invasion.

  8. Uranium bed oxidation vacuum process system

    International Nuclear Information System (INIS)

    McLeland, H.L.

    1977-01-01

    Deuterium and tritium gases are occluded in uranium powder for release into neutron generator tubes. The uranium powder is contained in stainless steel bottles, termed ''beds.'' If these beds become damaged, the gases must be removed and the uranium oxidized in order not to be flammable before shipment to ERDA disposal grounds. This paper describes the system and methods designed for the controlled degassing and oxidation process. The system utilizes sputter-ion, cryo-sorption and bellows pumps for removing the gases from the heated source bed. Removing the tritium gas is complicated by the shielding effect of helium-3, a byproduct of tritium decay. This effect is minimized by incremental pressure changes, or ''batch'' processing. To prevent runaway exothermic reaction, oxidation of the uranium bed is also done incrementally, or by ''batch'' processing, rather than by continuous flow. The paper discusses in detail the helium-3 shielding effect, leak checks that must be made during processing, bed oxidation, degree of gas depletion, purity of gases sorbed from beds, radioactivity of beds, bed disposal and system renovation

  9. Fluidised-bed combustion of gasification residue

    Energy Technology Data Exchange (ETDEWEB)

    Korpela, T.; Kudjoi, A.; Hippinen, I.; Heinolainen, A.; Suominen, M.; Lu Yong [Helsinki Univ. of Technology (Finland). Lab of Energy Economics and Power Plant Engineering

    1996-12-01

    Partial gasification processes have been presented as possibilities for future power production. In the processes, the solid materials removed from a gasifier (i.e. fly ash and bed material) contain unburnt fuel and the fuel conversion is increased by burning this gasification residue either in an atmospheric or a pressurised fluidised-bed. In this project, which is a part of European JOULE 2 EXTENSION research programme, the main research objectives are the behaviour of calcium and sulphur compounds in solids and the emissions of sulphur dioxide and nitrogen oxides (NO{sub x} and N{sub 2}O) in pressurised fluidised-bed combustion of gasification residues. (author)

  10. Updated Performance Evaluation of the ISS Water Processor Multifiltration Beds

    Science.gov (United States)

    Bowman, Elizabeth M.; Carter, Layne; Carpenter, Joyce; Orozco, Nicole; Weir, Natalee; Wilson, Mark

    2014-01-01

    The ISS Water Processor Assembly (WPA) produces potable water from a waste stream containing humidity condensate and urine distillate. The primary treatment process is achieved in the Multifiltration Beds, which include adsorbent media and ion exchange resin for the removal of dissolved organic and inorganic contaminants. Two Multifiltration Beds (MF Beds) were replaced on ISS in July 2010 after initial indication of inorganic breakthrough of the first bed and an increasing Total Organic Carbon (TOC) trend in the product water. The first bed was sampled and analyzed Sept 2011 through March 2012. The second MF Bed was sampled and analyzed June 2012 through August 2012. The water resident in the both beds was analyzed for various parameters to evaluate adsorbent loading, performance of the ion exchange resin, microbial activity, and generation of leachates from the ion exchange resin. Portions of the adsorbent media and ion exchange resin were sampled and subsequently desorbed to identify the primary contaminants removed at various points in the bed in addition to microbial analysis. Analysis of the second bed will be compared to results from the first bed to provide a comprehensive overview of how the Multifiltration Beds function on orbit. New data from the second bed supplements the analysis of the first bed (previously reported) and gives a more complete picture of breakthrough compounds, resin breakdown products, microbial activity, and difficult to remove compounds. The results of these investigations and implications to the operation of the WPA on ISS are documented in this paper.

  11. Fluid bed dryer and Aeropep solidification system

    International Nuclear Information System (INIS)

    1975-01-01

    Performance measurements were made on the model of the Fluidized-bed Calciner developed by Aerojet Liquid Rocket Co. The measurements were made over the period August 11-19, 1975, at the Sacramento location of the calciner. The purpose of the tests was to evaluate the performance of the ALRC Fluidized Bed Concentrator for the processing of simulated waste containing realistic concentrations and chemical forms of radioiodine. (auth)

  12. Using aerial photography and image analysis to measure changes in giant reed populations

    Science.gov (United States)

    A study was conducted along the Rio Grande in southwest Texas to evaluate color-infrared aerial photography combined with supervised image analysis to quantify changes in giant reed (Arundo donax L.) populations over a 6-year period. Aerial photographs from 2002 and 2008 of the same seven study site...

  13. Review of finite fields: Applications to discrete Fourier, transforms and Reed-Solomon coding

    Science.gov (United States)

    Wong, J. S. L.; Truong, T. K.; Benjauthrit, B.; Mulhall, B. D. L.; Reed, I. S.

    1977-01-01

    An attempt is made to provide a step-by-step approach to the subject of finite fields. Rigorous proofs and highly theoretical materials are avoided. The simple concepts of groups, rings, and fields are discussed and developed more or less heuristically. Examples are used liberally to illustrate the meaning of definitions and theories. Applications include discrete Fourier transforms and Reed-Solomon coding.

  14. Interaction between host T cells and Reed-Sternberg cells in Hodgkin lymphomas

    NARCIS (Netherlands)

    Poppema, S; van den Berg, Anke

    2000-01-01

    Recent studies provide evidence that Reed-Sternberg (R-S) cells produce factors that may explain the characteristic inflammatory infiltrate in the affected tissues of Hodgkin lymphoma. The various chemokines and cytokines that are produced lead to a preferential influx of Th2-type T cells and

  15. Analisa Kinerja Pengkodean Kanal Type Reed Solomon Coding pada Kualitas Transmisi Citra

    Directory of Open Access Journals (Sweden)

    Baharuddin

    2018-03-01

    Full Text Available Dalam sistem telekomunikasi, data multimedia berupa audio, citra, dan video ditransmisikan ke penerima melalui sebuah kanal komunikasi. Pada sistem telekomunikasi yang menggunakan kanal komunikasi wireless, selain pengaruh redaman, gangguan yang paling dominan adalah noise dan fading. Fading dan noise dikanal akan menurunkan kinerja sistem telekomunikasi digital karena dapat menyebabkan terjadinya kesalahan pendeteksian sinyal, sehingga terjadi perubahan bit atau simbol pada sisi penerima. Dengan menerapkan teknik pengkodean kanal tipe Reed Solomon Code pada sisi pengirim dan penerima, maka dapat ditingkatkan kinerja dari sistem komunikasi digital tersebut. Melalui simulasi dalam penelitian ini, telah dianalisa pengaruh penerapan teknik pengkodean kanal Reed Solomon Code pada sistem yang dipengaruhi noise Additive White Gaussian Noise (AWGN dan fading Rayleigh. Besarnya pengaruh penggunaan dari teknik pengkodean kanal Reed Solomon Code dapat diketahui melalui analisa Bit Error Rate (BER dan Peak Signal to Noise Ratio (PSNR. Hasil simulasi dari penelitian ini menunjukkan bahwa adanya peningkatan perbaikan sistem dipenerima rata-rata 5dB bila dibandingkan dengan tanpa menggunakan teknik pengkodean kanal Reed Solomon Code.

  16. Indexes of the common reed's seed vitality from water-bodies of the Chernobyl exclusive zone

    International Nuclear Information System (INIS)

    Yavnuk, A.A.; Shevtsova, N.L.; Gudkov, D.I.; Levchenko, Ya.I.

    2010-01-01

    Investigation of the common reed's seed vitality (vegetation of 2009) from flood-plain water-bodies with different level of radionuclide contamination was carried out. Decrease in indexes of seed's vitality and abnormalities in seed dynamic sprouting was noticed. Dose-response relationship of germination, germinating force, survival rate of seeds of plants was determined. (authors)

  17. Parallel Subspace Subcodes of Reed-Solomon Codes for Magnetic Recording Channels

    Science.gov (United States)

    Wang, Han

    2010-01-01

    Read channel architectures based on a single low-density parity-check (LDPC) code are being considered for the next generation of hard disk drives. However, LDPC-only solutions suffer from the error floor problem, which may compromise reliability, if not handled properly. Concatenated architectures using an LDPC code plus a Reed-Solomon (RS) code…

  18. Cryptic species of sharp-nosed reed frogs in the Hyperolius nasutus ...

    African Journals Online (AJOL)

    The sharp-nosed reed frog is widespread in Africa. Although currently recognized as one species, suggestions have been made that more than one species might exist. We analysed 237 calls of 69 males from 19 localities in the western to southern parts of Africa. Calls fall into three groups, which we recognize as cryptic ...

  19. Dilute oxalic acid pretreatment for biorefining giant reed (Arundo donax L.)

    Science.gov (United States)

    Danilo Scordia; Salvatore L. Cosentino; Jae-Won Lee; Thomas W. Jeffries

    2011-01-01

    Biomass pretreatment is essential to overcome recalcitrance of lignocellulose for ethanol production. In the present study we pretreated giant reed (Arundo donax L.), a perennial, rhizomatous lignocellulosic grass with dilute oxalic acid. The effects of temperature (170-190 ºC), acid loading (2-10% w/w) and reaction time (15-40 min) were handled as a single...

  20. Is shared male assistance with antiparasitic nest defence costly in the polygynous great reed warbler?

    Czech Academy of Sciences Publication Activity Database

    Požgayová, Milica; Procházka, Petr; Honza, Marcel

    2013-01-01

    Roč. 85, č. 3 (2013), s. 615-621 ISSN 0003-3472 R&D Projects: GA AV ČR IAA600930605; GA AV ČR IAA600930903 Institutional support: RVO:68081766 Keywords : great reed warbler * aggressive behaviour * brood parasitism * common cuckoo * mating status Subject RIV: EG - Zoology Impact factor: 3.068, year: 2013

  1. The Reed & Kellogg System of Sentence Diagramming and Its Implementation in Higher Education

    Science.gov (United States)

    Coats, Judith Ruth

    2012-01-01

    The purpose of this study was to research whether or not the intervention of the Reed & Kellogg System of sentence diagramming would make a significant difference in the acquisition, retention, and comprehension of the basic grammatical skills, including parts of speech, complements, phrases, clauses, and sentence structures, on the higher…

  2. Research on Noise Reduction of Reed Valves of a Hermetic Refrigerator Compressor

    Science.gov (United States)

    He, Zhilong; Chen, Qian; Li, Dantong; Wang, Ju; Xia, Pu; Wang, Tao

    2017-08-01

    The noise level of the refrigerator compressor has received more and more attention in recent years. As the key component of a compressor, reed valve is its main noise source. In this paper, a new noise reduction technology of coating on reed valve surface is proposed and verified by experiments. Firstly, the reed valves were coated, and their surface characteristics were checked. Then, the refrigerator compressor p-V diagram test was carried out to investigate the influence of doped diamond-like carbon (DLC) coating on power consumption. Finally, the noise test rig for the refrigerator compressor was set up. Based on the standard test method, noise spectrum was measured in a semi-anechoic room under standard working condition. Research results showed that the compressor noise was significantly reduced by 1.8dB (A) after coating. Moreover, the effect of aerodynamic noise reduction at suction side is better than that at discharge side. However, the influence of the film thickness on noise reduction value is little. The COP was reduced by 0.6% as compared to the compressor with uncoated reed valves.

  3. Power decoding Reed-Solomon codes up to the Johnson radius

    DEFF Research Database (Denmark)

    Rosenkilde, Johan Sebastian Heesemann

    2018-01-01

    Power decoding, or "decoding using virtual interleaving" is a technique for decoding Reed-Solomon codes up to the Sudan radius. Since the method's inception, it has been an open question if it is possible to use this approach to decode up to the Johnson radius - the decoding radius of the Guruswami...

  4. Reed Warbler Hosts Fine-Tune their Defenses to Track Three Decades of Cuckoo Decline

    Science.gov (United States)

    Thorogood, Rose; Davies, Nicholas B

    2013-01-01

    Interactions between avian hosts and brood parasites can provide a model for how animals adapt to a changing world. Reed warbler (Acrocephalus scirpaceus) hosts employ costly defenses to combat parasitism by common cuckoos (Cuculus canorus). During the past three decades cuckoos have declined markedly across England, reducing parasitism at our study site (Wicken Fen) from 24% of reed warbler nests in 1985 to 1% in 2012. Here we show with experiments that host mobbing and egg rejection defenses have tracked this decline in local parasitism risk: the proportion of reed warbler pairs mobbing adult cuckoos (assessed by responses to cuckoo mounts and models) has declined from 90% to 38%, and the proportion rejecting nonmimetic cuckoo eggs (assessed by responses to model eggs) has declined from 61% to 11%. This is despite no change in response to other nest enemies or mimetic model eggs. Individual variation in both defenses is predicted by parasitism risk during the host’s egg-laying period. Furthermore, the response of our study population to temporal variation in parasitism risk can also explain spatial variation in egg rejection behavior in other populations across Europe. We suggest that spatial and temporal variation in parasitism risk has led to the evolution of plasticity in reed warbler defenses. PMID:24299407

  5. Endotoxin, coliform, and dust levels in various types of rodent bedding.

    Science.gov (United States)

    Whiteside, Tanya E; Thigpen, Julius E; Kissling, Grace E; Grant, Mary G; Forsythe, Diane

    2010-03-01

    Endotoxins in grain dust, household dust, and animal bedding may induce respiratory symptoms in rodents and humans. We assayed the endotoxin, coliform, and dust levels in 20 types of rodent bedding. Endotoxin concentrations were measured by using a commercial test kit, coliform counts were determined by using conventional microbiologic procedures, and dust content was evaluated by using a rotating-tapping shaker. Paper bedding types contained significantly less endotoxin than did other bedding types; the highest levels of endotoxin were detected in hardwood and corncob beddings. The range of endotoxin content for each bedding type was: corncob bedding, 1913 to 4504 endotoxin units per gram (EU/g); hardwood bedding, 3121 to 5401 EU/g; corncob-paper mixed bedding, 1586 to 2416 EU/g; and paper bedding, less than 5 to 105 EU/g. Coliform counts varied from less than 10 to 7591 cfu/g in corncob beddings, 90 to 4010 cfu/g in corncob-paper mixed beddings, less than 10 to 137 cfu/g in hardwood beddings, and less than 10 cfu/g in paper beddings. Average dust content was less than 0.15% in all commercial bedding types. We conclude that paper bedding is the optimal bedding type for conducting LPS inhalation studies and that rodent bedding containing high levels of endotoxin may alter the results of respiratory and immunologic studies in rodents.

  6. Fluid-bed combustion

    Energy Technology Data Exchange (ETDEWEB)

    Hunt, G.; Schoebotham, N.

    1981-02-01

    In Energy Equipment Company's two-stage fluidized bed system, partial combustion in a fluidized bed is followed by burn-off of the generated gases above the bed. The system can be retrofitted to existing boilers, and can burn small, high ash coal efficiently. It has advantages when used as a hot gas generator for process drying. Tests on a boiler at a Cadbury Schweppes plant are reported.

  7. Fluidised bed combustion system

    International Nuclear Information System (INIS)

    McKenzie, E.C.

    1976-01-01

    Fluidized bed combustion systems that facilitates the maintenance of the depth of the bed are described. A discharge pipe projects upwardly into the bed so that bed material can flow into its upper end and escape downwardly. The end of the pipe is surrounded by an enclosure and air is discharged into the enclosure so that material will enter the pipe from within the enclosure and have been cooled in the enclosure by the air discharged into it. The walls of the enclosure may themselves be cooled

  8. Isolation, cloning, and characterization of a partial novel aro A gene in common reed (Phragmites australis).

    Science.gov (United States)

    Taravat, Elham; Zebarjadi, Alireza; Kahrizi, Danial; Yari, Kheirollah

    2015-05-01

    Among the essential amino acids, phenylalanine, tryptophan, and tyrosine are aromatic amino acids which are synthesized by the shikimate pathway in plants and bacteria. Herbicide glyphosate can inhibit the biosynthesis of these amino acids. So, identification of the gene tolerant to glyphosate is very important. It has been shown that the common reed or Phragmites australis Cav. (Poaceae) is relatively tolerant to glyphosate. The aim of the current research is identification, cloning, sequencing, and registering of partial aro A gene of the common reed P. australis. The partial aro A gene of common reed (P. australis) was cloned in Escherichia coli and the amino acid sequence was identified/determined for the first time. This is the first report for isolation, cloning, and sequencing of a part of aro A gene from the common reed. A 670 bp fragment including two introns (86 bp and 289 bp) was obtained. The open reading frame (ORF) region in part of gene was encoded for 98 amino acids. Alignment showed high similarity among this region with Zea mays (L.) (Poaceae) (94.6%), Eleusine indica L. Gaertn (Poaceae) (94.2%), and Zoysia japonica Steud. (Poaceae) (94.2%). The alignment of amino acid sequence of the investigated part of the gene showed a homology with aro A from several other plants. This conserved region forms the enzyme active site. The alignment results of nucleotide and amino acid residues with related sequences showed that there are some differences among them. The relative glyphosate tolerance in the common reed may be related to these differences.

  9. Efficient Round-Trip Time Optimization for Replica-Exchange Enveloping Distribution Sampling (RE-EDS).

    Science.gov (United States)

    Sidler, Dominik; Cristòfol-Clough, Michael; Riniker, Sereina

    2017-06-13

    Replica-exchange enveloping distribution sampling (RE-EDS) allows the efficient estimation of free-energy differences between multiple end-states from a single molecular dynamics (MD) simulation. In EDS, a reference state is sampled, which can be tuned by two types of parameters, i.e., smoothness parameters(s) and energy offsets, such that all end-states are sufficiently sampled. However, the choice of these parameters is not trivial. Replica exchange (RE) or parallel tempering is a widely applied technique to enhance sampling. By combining EDS with the RE technique, the parameter choice problem could be simplified and the challenge shifted toward an optimal distribution of the replicas in the smoothness-parameter space. The choice of a certain replica distribution can alter the sampling efficiency significantly. In this work, global round-trip time optimization (GRTO) algorithms are tested for the use in RE-EDS simulations. In addition, a local round-trip time optimization (LRTO) algorithm is proposed for systems with slowly adapting environments, where a reliable estimate for the round-trip time is challenging to obtain. The optimization algorithms were applied to RE-EDS simulations of a system of nine small-molecule inhibitors of phenylethanolamine N-methyltransferase (PNMT). The energy offsets were determined using our recently proposed parallel energy-offset (PEOE) estimation scheme. While the multistate GRTO algorithm yielded the best replica distribution for the ligands in water, the multistate LRTO algorithm was found to be the method of choice for the ligands in complex with PNMT. With this, the 36 alchemical free-energy differences between the nine ligands were calculated successfully from a single RE-EDS simulation 10 ns in length. Thus, RE-EDS presents an efficient method for the estimation of relative binding free energies.

  10. Emissions of CO2 and CH4 from sludge treatment reed beds depend on system management and sludge loading

    DEFF Research Database (Denmark)

    Olsson, Linda; Dam Larsen, Julie; Ye, Siyuan

    2014-01-01

    , the SD had no vegetation and a poor dewatering capacity, which resulted in anaerobic conditions favoring CH4 emission. In contrast, the well-managed STRB had more aerobic conditions in the sludge residue resulting in low CH4 emission rates. We conclude that well-designed and well-managed STRBs have a low...

  11. Biodegradation of phenolic waste liquors in stirred-tank, packed-bed, and fluidized-bed bioreactors

    Energy Technology Data Exchange (ETDEWEB)

    Holladay, D W; Hancher, G W; Chilcote, D D; Scott, C D

    1978-11-01

    The biological degradation of phenolic scrub liquors similar to those that arise in coal conversion processes was studied for symbiotic bacterial populations contained in a continuously stirred tank bioreactor, a three-phase packed-bed bioreactor, and a three-phase, fluidized-bed bioreactor. The conversions of phenol compounds were comparable in the three-phase, packed-bed bioreactor and the continuously stirred tank bioreactor; however, the packed-bed bioreactor degradation rates were as much as twice those in the continuously stirred tank bioreactor, and packed-bed bioreactor retention times were as low as one- tenth those of the continuously stirred tank bioreactors (minimum time was 12 hours).

  12. Fluidized bed incinerator development

    International Nuclear Information System (INIS)

    Ziegler, D.L.; Johnson, A.J.

    1976-01-01

    A fluidized bed incinerator is being developed for burning rad contaminated solid and liquid waste materials. In situ neutralization of acid gases by the bed material, catalytic afterburning, and gas filtration are used to produce a clean flue gas without the use of aqueous scrubbing

  13. Fluidized-bed firing of washery wastes

    Energy Technology Data Exchange (ETDEWEB)

    Rubin, Yu M; Gavrik, M V

    1978-01-01

    Tailings containing SiO2 (56.76%), A12O3 (25.63%), Fe2O3 (10.22%) plus CaO, MgO and SOat3 were fluidized at 1.7-2.0 m/s. This gives a uniform pressure of 6 kg-f/m2 at bed heights of 100 mm, though this is higher in the upper layers where the fine material tends to concentrate. The resistance of the bed is directly proportional to its height. Minimum oxygen, maximum carbon dioxide and maximum temperature are found in the section 250-300 mm above the grid (bed height 500 mm); in the upper zone of the bed, some decrease in temperature and carbon dioxide, and increase in oxygen are associated with the ingress of air through the discharge chute. Waste heat should be utilised to help to cover costs of desulphurising stack gases.

  14. Walter Reed Army Medical Center (WRAMC) and Office of Management and Budget (OMB) Circular A-76: Implications for the Future

    National Research Council Canada - National Science Library

    Grasso, Valerie B

    2007-01-01

    This report examines the issues surrounding the recent Walter Reed public-private competition conducted under OMB Circular A-76 and its potential impact on future Department of Defense competitions...

  15. Analysis of magnetic field and hysteresis of reed switches for control rod position indicator of SMART CEDM

    International Nuclear Information System (INIS)

    Yoo, J. W.; Kim, J. H.; Heo, H.; Kim, J. I.; Jang, M. H.

    2002-01-01

    The reliability and accuracy of the information on control rod position are very important to the reactor safety and the design of the core protection system. A survey on the RSPT(Reed Switch Position Transmitter) type control rod position indication system and its actual implementation in the exiting nuclear power plants in Korea was performed first. The control rod position indicator having the high performance for SMART was developed on the basis of RSPT technology identified through the survey. The hysteresis of reed switches is one of the important factors in a repeat accuracy of control rod position indication. In this study, the hysteresis of reed switches is introduced and the design method using the magnetic analysis of reed switches in presented

  16. Regeneration and propagation of reed grass for large-scale ...

    African Journals Online (AJOL)

    전서범

    2012-01-26

    Jan 26, 2012 ... Full Length Research Paper ... cultivated without fertilizer, irrigation or pesticides ... magenta vessels containing MS medium without any growth ... Effect of 2,4 D and 4-FA on callus formation from nodal stem tissue of P.

  17. Shoot cuttings propagation of giant reed (Arundo donax L.) in water and moist soil: The path forward?

    Energy Technology Data Exchange (ETDEWEB)

    Ceotto, Enrico; Di Candilo, Mario [C.R.A. - Centro di Ricerca per le Colture Industriali, Via di Corticella 133, 40128 Bologna (Italy)

    2010-11-15

    Giant reed (Arundo donax L.) is a perennial rhizomatous grass that can be regarded as an ideal crop for bioenergy production, owing to several intrinsic characteristics. Despite to the promising yield results obtained in many plot experiments, the cultivation of giant reed at field scale is still a challenge. Owing to the floral sterility of the species, rhizome propagation has been predominantly used to establish field plots experiments, although this method is unpractical and monetarily expensive. Giant reed is a hydrophytic plant that typically spread in riparian systems by flood-mediated fragmentation and dispersal of vegetative propagules. Since giant reed propagation is strictly dependent on temporary abundance of water, this plant characteristic might be exploited for fostering the diffusion of giant reed as a bioenergy field crop. The objectives of this paper were: i) to disseminate some techniques for shoot cutting propagation of giant reed in water and in moist soil; ii) to address the critical points that remain to be solved for a widespread diffusion of this species as a bioenergy field crop. (author)

  18. Solid phase transport in series fluidised bed reactors

    International Nuclear Information System (INIS)

    Hayes, M.R.

    1980-01-01

    In a multistage counter-current fluidised bed column, fluidised bed material is recycled within each stage and a fraction is continuously withdrawn to the next lower stage at a rate dependent only on the rate of removal of the fluidised bed material from the base of the column. It has a particular application to the ion exchange treatment of liquids containing suspended solids, for example leach solutions from uranium ores. (author)

  19. Fluidized-bed calciner with combustion nozzle and shroud

    International Nuclear Information System (INIS)

    Wielang, J.A.; Palmer, W.B.; Kerr, W.B.

    1977-01-01

    A nozzle employed as a burner within a fluidized bed is coaxially enclosed within a tubular shroud that extends beyond the nozzle length into the fluidized bed. The open-ended shroud portion beyond the nozzle end provides an antechamber for mixture and combustion of atomized fuel with an oxygen-containing gas. The arrangement provides improved combustion efficiency and excludes bed particles from the high-velocity, high-temperature portions of the flame to reduce particle attrition. 4 claims, 2 figures

  20. Key-equations for list decoding of Reed-Solomon codes and how to solve them

    DEFF Research Database (Denmark)

    Beelen, Peter; Brander, Kristian

    2010-01-01

    A Reed-Solomon code of length n can be list decoded using the well-known Guruswami-Sudan algorithm. By a result of Alekhnovich (2005) the interpolation part in this algorithm can be done in complexity O(s^4l^4nlog^2nloglogn), where l denotes the designed list size and s the multiplicity parameter....... The parameters l and s are sometimes considered to be constants in the complexity analysis, but for high rate Reed-Solomon codes, their values can be very large. In this paper we will combine ideas from Alekhnovich (2005) and the concept of key equations to get an algorithm that has complexity O(sl^4nlog^2...

  1. On locality of Generalized Reed-Muller codes over the broadcast erasure channel

    KAUST Repository

    Alloum, Amira

    2016-07-28

    One to Many communications are expected to be among the killer applications for the currently discussed 5G standard. The usage of coding mechanisms is impacting broadcasting standard quality, as coding is involved at several levels of the stack, and more specifically at the application layer where Rateless, LDPC, Reed Slomon codes and network coding schemes have been extensively studied, optimized and standardized in the past. Beyond reusing, extending or adapting existing application layer packet coding mechanisms based on previous schemes and designed for the foregoing LTE or other broadcasting standards; our purpose is to investigate the use of Generalized Reed Muller codes and the value of their locality property in their progressive decoding for Broadcast/Multicast communication schemes with real time video delivery. Our results are meant to bring insight into the use of locally decodable codes in Broadcasting. © 2016 IEEE.

  2. Effects of bleaching wastewater irrigation on soil quality of constructed reed wetlands

    Directory of Open Access Journals (Sweden)

    Cheng Ding

    2016-10-01

    Full Text Available Constructed reed wetland microcosms (CRWs in a lab of east China have been irrigated with bleaching wastewater per month for a reed growth season. The soil physicochemical properties, enzyme activities (i.e. urease, invertase, polyphenol oxidase, alkaline phosphatase and cellulase and soil microbial diversity were assayed before and after the exposure experiment. Compared to the river water irrigated controls (CKs, bleaching wastewater application has no marked influence on soil pH, but significantly increased soil Na+, total halogen and absorbable organic halogen (AOX contents, which induced the increasing of soil electrical conductivity. Furthermore, soil enzyme activities displayed significant variation (except for polyphenol oxidase. Bleaching wastewater irrigation decreased Sorenson’s pairwise similarity coefficient (Cs, which indicated the changes of the structure of bacterial and fungal communities. However, only the diversity of bacterial community was inhibited and has no effect on the diversity of fungal community, as evidenced by the calculated Shannon–Wiener index (H.

  3. Development of control rod position indicator using seismic-resistance reed switches for integral reactor

    International Nuclear Information System (INIS)

    Yu, Je Yong; Kim, Ji Ho; Huh, Hyung; Choi, Myoung Hwan; Sohn, Dong Seong

    2008-01-01

    The Reed Switch Position Transmitter (RSPT) is used as a position indicator for the control rod in commercial nuclear power plants made by ABB-CE. But this position indicator has some problems when directly adopting it to the integral reactor. The Control Element Drive Mechanism (CEDM) for the integral reactor is designed to raise and lower the control rod in steps of 2mm in order to satisfy the design features of the integral reactor which are the soluble boron free operation and the use of a nuclear heating for the reactor start-up. Therefore the resolution of the position indicator for the integral reactor should be achieved to sense the position of the control rod more precisely than that of the RSPT of the ABB-CE. This paper adopts seismic resistance reed switches to the position indicator in order to reduce the damages or impacts during the handling of the position indicator and earthquake

  4. General Purpose Graphics Processing Unit Based High-Rate Rice Decompression and Reed-Solomon Decoding

    Energy Technology Data Exchange (ETDEWEB)

    Loughry, Thomas A. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-02-01

    As the volume of data acquired by space-based sensors increases, mission data compression/decompression and forward error correction code processing performance must likewise scale. This competency development effort was explored using the General Purpose Graphics Processing Unit (GPGPU) to accomplish high-rate Rice Decompression and high-rate Reed-Solomon (RS) decoding at the satellite mission ground station. Each algorithm was implemented and benchmarked on a single GPGPU. Distributed processing across one to four GPGPUs was also investigated. The results show that the GPGPU has considerable potential for performing satellite communication Data Signal Processing, with three times or better performance improvements and up to ten times reduction in cost over custom hardware, at least in the case of Rice Decompression and Reed-Solomon Decoding.

  5. Thermal-hydraulic and characteristic models for packed debris beds

    International Nuclear Information System (INIS)

    Mueller, G.E.; Sozer, A.

    1986-12-01

    APRIL is a mechanistic core-wide meltdown and debris relocation computer code for Boiling Water Reactor (BWR) severe accident analyses. The capabilities of the code continue to be increased by the improvement of existing models. This report contains information on theory and models for degraded core packed debris beds. The models, when incorporated into APRIL, will provide new and improved capabilities in predicting BWR debris bed coolability characteristics. These models will allow for a more mechanistic treatment in calculating temperatures in the fluid and solid phases in the debris bed, in determining debris bed dryout, debris bed quenching from either top-flooding or bottom-flooding, single and two-phase pressure drops across the debris bed, debris bed porosity, and in finding the minimum fluidization mass velocity. The inclusion of these models in a debris bed computer module will permit a more accurate prediction of the coolability characteristics of the debris bed and therefore reduce some of the uncertainties in assessing the severe accident characteristics for BWR application. Some of the debris bed theoretical models have been used to develop a FORTRAN 77 subroutine module called DEBRIS. DEBRIS is a driver program that calls other subroutines to analyze the thermal characteristics of a packed debris bed. Fortran 77 listings of each subroutine are provided in the appendix

  6. Hybrid reed: Solid-state devices are a new generation of protective relays

    Directory of Open Access Journals (Sweden)

    Gurevich Vladimir

    2007-01-01

    Full Text Available Research and development in the field of electromechanical protective relays has not been conducted for tens of years. Author’s approach allows viewing the problem of re-equipment of relay protection in a new way. In the author’s opinion combination of reed switches with magnetic circuits and semiconductor elements opens new avenues in development of the promising protective relays featuring reliability, simplicity and low cost. Examples of protective relays made with these elements are given below.

  7. The vibrating reed frequency meter: digital investigation of an early cochlear model

    Directory of Open Access Journals (Sweden)

    Andrew Bell

    2015-10-01

    Full Text Available The vibrating reed frequency meter, originally employed by Békésy and later by Wilson as a cochlear model, uses a set of tuned reeds to represent the cochlea’s graded bank of resonant elements and an elastic band threaded between them to provide nearest-neighbour coupling. Here the system, constructed of 21 reeds progressively tuned from 45 to 55 Hz, is simulated numerically as an elastically coupled bank of passive harmonic oscillators driven simultaneously by an external sinusoidal force. To uncover more detail, simulations were extended to 201 oscillators covering the range 1–2 kHz. Calculations mirror the results reported by Wilson and show expected characteristics such as traveling waves, phase plateaus, and a response with a broad peak at a forcing frequency just above the natural frequency. The system also displays additional fine-grain features that resemble those which have only recently been recognised in the cochlea. Thus, detailed analysis brings to light a secondary peak beyond the main peak, a set of closely spaced low-amplitude ripples, rapid rotation of phase as the driving frequency is swept, frequency plateaus, clustering, and waxing and waning of impulse responses. Further investigation shows that each reed’s vibrations are strongly localised, with small energy flow along the chain. The distinctive set of equally spaced ripples is an inherent feature which is found to be largely independent of boundary conditions. Although the vibrating reed model is functionally different to the standard transmission line, its cochlea-like properties make it an intriguing local oscillator model whose relevance to cochlear mechanics needs further investigation.

  8. The Protective Properties of Common Reed Plantations on Shores of the Lower Volga Region

    Directory of Open Access Journals (Sweden)

    Solodovnikov Denis Anatolyevich

    2014-12-01

    Full Text Available The abrasion processing of shores is a pressing problem of large water basins of the Lower Volga region and other Russian regions. About 3 km2 of shoreland is annually lost in the zone of the Volgograd water basin as a result of this process. The existing methods of shores protection are connected with the creation of concrete structures having a high level of erosion resistance. They are extremely expensive and in most cases they are not affordable for rural municipalities suffering from abrasion. The authors offer cheap and environmentally friendly way of protecting the shores of large water basins from abrasion. The method is based on the plantation of a common reed strip on a water basin’s shallow. The biological characteristics of common reed as the main component of shore protection structures are described. The terms and milestones of the work in the conditions of the Volgograd water basin are developed. The main result of applying our methodology is the complete cessation of abrasion processing of the shore at the corresponding piece of land. The authors overview the positive qualities of reed plantations, their biocenotic, barrier and waterproof role in on-shore ecosystems. The application of the described method will allow saving for the national economy dozens of hectares of valuable shore lands annually, in particular, irrigated cropland, settlement lands, infrastructure. In addition to the direct benefits associated with the conservation of land resources, the intensity of adverse processes associated with erosion of shores (water basin muddying, deterioration of sanitary qualities of water will decrease. Due to the wide geographic spread of common reed described in the present work, the technology of shores stabilization can be applied at almost all lowland water basins of Russia.

  9. The fast decoding of Reed-Solomon codes using Fermat theoretic transforms and continued fractions

    Science.gov (United States)

    Reed, I. S.; Scholtz, R. A.; Welch, L. R.; Truong, T. K.

    1978-01-01

    It is shown that Reed-Solomon (RS) codes can be decoded by using a fast Fourier transform (FFT) algorithm over finite fields GF(F sub n), where F sub n is a Fermat prime, and continued fractions. This new transform decoding method is simpler than the standard method for RS codes. The computing time of this new decoding algorithm in software can be faster than the standard decoding method for RS codes.

  10. Bed Bugs FAQs

    Science.gov (United States)

    ... Europe. Bed bugs have been found in five-star hotels and resorts and their presence is not ... Health – Division of Parasitic Diseases Email Recommend Tweet YouTube Instagram Listen Watch RSS ABOUT About CDC Jobs ...

  11. Bed Bug Information Clearinghouse

    Science.gov (United States)

    Its purpose is to help states, communities, and consumers in efforts to prevent and control bed bug infestations. Currently includes only reviewed material from federal/state/local government agencies, extension services, and universities.

  12. Idealized digital models for conical reed instruments, with focus on the internal pressure waveform.

    Science.gov (United States)

    Kergomard, J; Guillemain, P; Silva, F; Karkar, S

    2016-02-01

    Two models for the generation of self-oscillations of reed conical woodwinds are presented. The models use the fewest parameters (of either the resonator or the exciter), whose influence can be quickly explored. The formulation extends iterated maps obtained for lossless cylindrical pipes without reed dynamics. It uses spherical wave variables in idealized resonators, with one parameter more than for cylinders: the missing length of the cone. The mouthpiece volume equals that of the missing part of the cone, and is implemented as either a cylindrical pipe (first model) or a lumped element (second model). Only the first model adds a length parameter for the mouthpiece and leads to the solving of an implicit equation. For the second model, any shape of nonlinear characteristic can be directly considered. The complex characteristic impedance for spherical waves requires sampling times smaller than a round trip in the resonator. The convergence of the two models is shown when the length of the cylindrical mouthpiece tends to zero. The waveform is in semi-quantitative agreement with experiment. It is concluded that the oscillations of the positive episode of the mouthpiece pressure are related to the length of the missing part, not to the reed dynamics.

  13. Reed Reactor Facility final report, September 1, 1995--August 31, 1996

    International Nuclear Information System (INIS)

    1997-01-01

    This report covers the period from September 1, 1995 to August 31, 1996. This report is intended to fulfill several purposes including the reporting requirements of the US Nuclear Regulatory Commission, the US Department of Energy, and the Oregon Department of Energy. Highlights of the last year include: student participation in the program is very high; the facility continues its success in obtaining donated equipment from the Portland General Electric, US Department of Energy, and other sources; the facility is developing more paid work; progress is being made in a collaborative project with Pacific Northwest National Laboratory on isotope production for medical purposes. There were over 1,500 individual visits to the Reactor Facility during the year. Most were students in classes at Reed College or area universities, colleges, and high schools. Including tours and research conducted at the facility, the Reed Reactor Facility contributed to the educational programs of six colleges and universities in addition to eighteen pre-college groups. During the year, the reactor was operated almost three hundred separate times. The total energy production was over 23 MW-hours. The reactor staff consists of a Director, an Associated Director, a contract Health Physicist, and approximately twenty Reed College undergraduate students as hourly employees. All radiation exposures to individuals during this year were well below 5% of the federal limits

  14. Reed Reactor Facility final report, September 1, 1995--August 31, 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-01

    This report covers the period from September 1, 1995 to August 31, 1996. This report is intended to fulfill several purposes including the reporting requirements of the US Nuclear Regulatory Commission, the US Department of Energy, and the Oregon Department of Energy. Highlights of the last year include: student participation in the program is very high; the facility continues its success in obtaining donated equipment from the Portland General Electric, US Department of Energy, and other sources; the facility is developing more paid work; progress is being made in a collaborative project with Pacific Northwest National Laboratory on isotope production for medical purposes. There were over 1,500 individual visits to the Reactor Facility during the year. Most were students in classes at Reed College or area universities, colleges, and high schools. Including tours and research conducted at the facility, the Reed Reactor Facility contributed to the educational programs of six colleges and universities in addition to eighteen pre-college groups. During the year, the reactor was operated almost three hundred separate times. The total energy production was over 23 MW-hours. The reactor staff consists of a Director, an Associated Director, a contract Health Physicist, and approximately twenty Reed College undergraduate students as hourly employees. All radiation exposures to individuals during this year were well below 5% of the federal limits.

  15. Reduction of the suction losses through reed valves in hermetic reciprocating compressors using a magnet coil

    Science.gov (United States)

    Hopfgartner, J.; Posch, S.; Zuber, B.; Almbauer, R.; Krischan, K.; Stangl, S.

    2017-08-01

    Reed valves are widely used in hermetic reciprocating compressors and are responsible for a large part of the thermodynamic losses. Especially, the suction valve, which is opened nearly during the whole suction stroke, has a big potential for improvement. Usually, suction valves are opened only by vacuum created by the moving piston and should be closed before the compression stroke starts to avoid a reversed mass-flow through the valve. Therefore, the valves are prestressed, which results on the other hand in a higher flow resistance. In this work, a suction valve is investigated, which is not closed by the preload of the valve but by an electromagnetic coil located in the suction muffler neck. Shortly before the piston reaches its bottom dead centre, voltage is applied to the coil and a magnetic force is generated which pulls the valve shut. Thereby, the flow resistance through the valve can be reduced by changing the preload on the reed valve because it is no longer needed to close the valve. The investigation of this adapted valve and the electromagnetic coil is firstly done by numerical simulations including fluid structure interactions of the reed valves of a reciprocating compressor and secondly by experiments made on a calorimeter test bench.

  16. Past and Present Resource Disputes in the South China Sea: The Case of Reed Bank

    Directory of Open Access Journals (Sweden)

    Micah S. Muscolino

    2013-09-01

    Full Text Available In 2012, tensions flared between China and the Philippines over plans to drill for oil in the Reed Bank, a disputed shoal in the South China Sea, rekindling fears about the possibility of military conflict over the area’s energy resources. This article shows that international controversy centering on the Reed Bank’s hydrocarbon reserves initially emerged during the oil crisis of the 1970s, when the pursuit of energy resources transformed the islets into a hotly contested area. As in recent years, oil exploration by multinational corporations in conjunction with the Philippines catalyzed international disputes. Vigorous protests from China and other nations that lay claim to territories in the South China Sea prompted the Philippines to assert its own jurisdictional claims. The territorial dispute pushed claimants to the brink of military confrontation in the 1970s, yet armed conflict failed to materialize. By examining the initial round of tensions surrounding oil exploration at Reed Bank, this article situates the current international competition for the South China Sea’s energy resources in historical perspective. Analyzing past disputes and their ultimate resolution offers insights into the dynamics of present tensions, while making it possible to critically engage with arguments predicting future “resource wars” in the South China Sea.

  17. Invertebrate populations in miscanthus (Miscanthusxgiganteus) and reed canary-grass (Phalaris arundinacea) fields

    Energy Technology Data Exchange (ETDEWEB)

    Semere, T.; Slater, F.M. [Llysdinam Field Centre, School of Biosciences, Cardiff University, Newbridge-on-Wye, Llandrindod Wells, Powys, LD1 6NB (United Kingdom)

    2007-01-15

    Monitoring of invertebrates at four field sites in Herefordshire, England, growing miscanthus and reed canary-grass was carried out in 2002, 2003 and 2004 to investigate the ecological impact of these crops on ground beetles, butterflies and arboreal invertebrates. Ground beetles were sampled by pitfall trapping; and arboreal invertebrates by sweep netting and stem beating. The Centre for Ecology and Hydrology's Butterflies Monitoring Scheme methodology was used to record butterflies. The effects of the biomass crops on invertebrates were indirect, through the use of weeds as food resources and habitat. The greater diversity of weed flora within miscanthus fields than within reed canary-grass fields had a greater positive effect on invertebrates. Ground beetles, butterflies and arboreal invertebrates were more abundant and diverse in the most floristically diverse miscanthus fields. The difference in crop architecture and development between miscanthus and reed canary-grass was reflected in their differences in crop height and ground cover early on in the season. However, most of the difference in arthropod abundance between the two crops was attributed to the difference in the agronomic practice of growing the crops such as plant density, and the effect of this on weed growth. Since perennial rhizomatous grasses require a single initial planting and related tillage, and also no major chemical inputs; and because the crops are harvested in the spring and the land is not disturbed by cultivation every year, the fields were used as over-wintering sites for invertebrates suggesting immediate benefits to biodiversity. (author)

  18. How dynamic are ice-stream beds?

    Science.gov (United States)

    Davies, Damon; Bingham, Robert G.; King, Edward C.; Smith, Andrew M.; Brisbourne, Alex M.; Spagnolo, Matteo; Graham, Alastair G. C.; Hogg, Anna E.; Vaughan, David G.

    2018-05-01

    Projections of sea-level rise contributions from West Antarctica's dynamically thinning ice streams contain high uncertainty because some of the key processes involved are extremely challenging to observe. An especially poorly observed parameter is sub-decadal stability of ice-stream beds, which may be important for subglacial traction, till continuity and landform development. Only two previous studies have made repeated geophysical measurements of ice-stream beds at the same locations in different years, but both studies were limited in spatial extent. Here, we present the results from repeat radar measurements of the bed of Pine Island Glacier, West Antarctica, conducted 3-6 years apart, along a cumulative ˜ 60 km of profiles. Analysis of the correlation of bed picks between repeat surveys shows that 90 % of the bed displays no significant change despite the glacier increasing in speed by up to 40 % over the last decade. We attribute the negligible detection of morphological change at the bed of Pine Island Glacier to the ubiquitous presence of a deforming till layer, wherein sediment transport is in steady state, such that sediment is transported along the basal interface without inducing morphological change to the radar-sounded basal interface. Given the precision of our measurements, the upper limit of subglacial erosion observed here is 500 mm a-1, far exceeding erosion rates reported for glacial settings from proglacial sediment yields, but substantially below subglacial erosion rates of 1.0 m a-1 previously reported from repeat geophysical surveys in West Antarctica.

  19. Seaweed beds support more juvenile reef fish than seagrass beds in a south-western Atlantic tropical seascape

    Science.gov (United States)

    Eggertsen, L.; Ferreira, C. E. L.; Fontoura, L.; Kautsky, N.; Gullström, M.; Berkström, C.

    2017-09-01

    Seascape connectivity is regarded essential for healthy reef fish communities in tropical shallow systems. A number of reef fish species use separate adult and nursery habitats, and hence contribute to nutrient and energy transfer between habitats. Seagrass beds and mangroves often constitute important nursery habitats, with high structural complexity and protection from predation. Here, we investigated if reef fish assemblages in the tropical south-western Atlantic demonstrate ontogenetic habitat connectivity and identify possible nurseries on three reef systems along the eastern Brazilian coast. Fish were surveyed in fore reef, back reef, Halodule wrightii seagrass beds and seaweed beds. Seagrass beds contained lower abundances and species richness of fish than expected, while Sargassum-dominated seaweed beds contained significantly more juveniles than all other habitats (average juvenile fish densities: 32.6 per 40 m2 in Sargassum beds, 11.2 per 40 m2 in back reef, 10.1 per 40 m2 in fore reef, and 5.04 per 40 m2 in seagrass beds), including several species that are found in the reef habitats as adults. Species that in other regions worldwide (e.g. the Caribbean) utilise seagrass beds as nursery habitats were here instead observed in Sargassum beds or back reef habitats. Coral cover was not correlated to adult fish distribution patterns; instead, type of turf was an important variable. Connectivity, and thus pathways of nutrient transfer, seems to function differently in east Brazil compared to many tropical regions. Sargassum-dominated beds might be more important as nurseries for a larger number of fish species than seagrass beds. Due to the low abundance of structurally complex seagrass beds we suggest that seaweed beds might influence adult reef fish abundances, being essential for several keystone species of reef fish in the tropical south-western Atlantic.

  20. Analysis of in situ water velocity distributions in the lowland river floodplain covered by grassland and reed marsh habitats - a case study of the bypass channel of Warta River (Western Poland

    Directory of Open Access Journals (Sweden)

    Laks Ireneusz

    2017-12-01

    Full Text Available The analysis of in situ measurements of velocity distribution in the floodplain of the lowland river has been carried out. The survey area was located on a bypass channel of the Warta River (West of Poland which is filled with water only in case of flood waves. The floodplain is covered by grassland and reed marsh habitats. The velocity measurements were performed with an acoustic Doppler current profiler (ADCP in a cross-section with a bed reinforced with concrete slabs. The measured velocities have reflected the differentiated impact of various vegetation types on the loss of water flow energy. The statistical analyses have proven a relationship between the local velocities and the type of plant communities.

  1. Fluidised bed heat exchangers

    International Nuclear Information System (INIS)

    Elliott, D.E.; Healey, E.M.; Roberts, A.G.

    1974-01-01

    Problems that have arisen during the initial stages of development of fluidised bed boilers in which heat transfer surfaces are immersed in fluidised solids are discussed. The very high heat transfer coefficients that are obtained under these conditions can be exploited to reduce the total heat transfer surface to a fraction of that in normal boilers. However, with the high heat flux levels involved, tube stressing becomes more important and it is advantageous to use smaller diameter tubes. One of the initial problems was that the pumping power absorbed by the fluidised bed appeared to be high. The relative influence of the fluidising velocity (and the corresponding bed area), tube diameter, tube spacing, heat transfer coefficient and bed temperature on pumping power and overall cost was determined. This showed the importance of close tube packing and research was undertaken to see if this would adversely affect the heat transfer coefficient. Pressure operation also reduces the pumping power. Fouling and corrosion tests in beds burning coal suggest that higher temperatures could be reached reliably and cost studies show that, provided the better refractory metals are used, the cost of achieving higher temperatures is not unduly high. It now remains to demonstrate at large scale that the proposed systems are viable and that the methods incorporated to overcome start up and part lead running problems are satisfactory. The promising role of these heat transfer techniques in other applications is briefly discussed

  2. in Spouted Bed

    Directory of Open Access Journals (Sweden)

    Bronislaw Buczek

    2013-01-01

    Full Text Available Samples of active coke, fresh and spent after cleaning flue gases from communal waste incinerators, were investigated. The outer layers of both coke particles were separately removed by comminution in a spouted bed. The samples of both active cokes were analysed by means of densities, mercury porosimetry, and adsorption technique. Remaining cores were examined to determine the degree of consumption of coke by the sorption of hazardous emissions (SO2, HCl, and heavy metals through its bed. Differences in contamination levels within the porous structure of the particles were estimated. The study demonstrated the effectiveness of commercial active coke in the cleaning of flue gases.

  3. The Safety of Hospital Beds

    Science.gov (United States)

    Gervais, Pierre; Pooler, Charlotte; Merryweather, Andrew; Doig, Alexa K.; Bloswick, Donald

    2015-01-01

    To explore the safety of the standard and the low hospital bed, we report on a microanalysis of 15 patients’ ability to ingress, move about the bed, and egress. The 15 participants were purposefully selected with various disabilities. Bed conditions were randomized with side rails up or down and one low bed with side rails down. We explored the patients’ use of the side rails, bed height, ability to lift their legs onto the mattress, and ability to turn, egress, and walk back to the chair. The standard bed was too high for some participants, both for ingress and egress. Side rails were used by most participants when entering, turning in bed, and exiting. We recommend that side rails be reconsidered as a means to facilitate in-bed movement, ingress, and egress. Furthermore, single deck height settings for all patients are not optimal. Low beds as a safety measure must be re-evaluated. PMID:28462302

  4. Blood profile and meat quality of Holstein-Friesian steers finished on total mixed ration or flaxseed oil-supplemented pellet mixed with reed canary grass haylage.

    Science.gov (United States)

    Utama, D T; Lee, S G; Baek, K H; Chung, W S; Chung, I A; Kim, D I; Kim, G Y; Lee, S K

    2018-02-01

    . According to daily cost, carcass weight and n-6 to n-3 FAs ratio, the finishing diet containing flaxseed oil-supplemented pellets and reed canary grass haylage at the as-fed ratio of 40 : 60 could be beneficial for the production of n-3-enriched beef.

  5. Apparatus for controlling fluidized beds

    Science.gov (United States)

    Rehmat, A.G.; Patel, J.G.

    1987-05-12

    An apparatus and process are disclosed for control and maintenance of fluidized beds under non-steady state conditions. An ash removal conduit is provided for removing solid particulates from a fluidized bed separate from an ash discharge conduit in the lower portion of the grate supporting such a bed. The apparatus and process of this invention is particularly suitable for use in ash agglomerating fluidized beds and provides control of the fluidized bed before ash agglomeration is initiated and during upset conditions resulting in stable, sinter-free fluidized bed maintenance. 2 figs.

  6. MIT pebble bed reactor project

    Energy Technology Data Exchange (ETDEWEB)

    Kadak, Andrew C. [Massachusetts Institute of Technology, Cambridge (United States)

    2007-03-15

    The conceptual design of the MIT modular pebble bed reactor is described. This reactor plant is a 250 Mwth, 120 Mwe indirect cycle plant that is designed to be deployed in the near term using demonstrated helium system components. The primary system is a conventional pebble bed reactor with a dynamic central column with an outlet temperature of 900 C providing helium to an intermediate helium to helium heat exchanger (IHX). The outlet of the IHX is input to a three shaft horizontal Brayton Cycle power conversion system. The design constraint used in sizing the plant is based on a factory modularity principle which allows the plant to be assembled 'Lego' style instead of constructed piece by piece. This principle employs space frames which contain the power conversion system that permits the Lego-like modules to be shipped by truck or train to sites. This paper also describes the research that has been conducted at MIT since 1998 on fuel modeling, silver leakage from coated fuel particles, dynamic simulation, MCNP reactor physics modeling and air ingress analysis.

  7. MIT pebble bed reactor project

    International Nuclear Information System (INIS)

    Kadak, Andrew C.

    2007-01-01

    The conceptual design of the MIT modular pebble bed reactor is described. This reactor plant is a 250 Mwth, 120 Mwe indirect cycle plant that is designed to be deployed in the near term using demonstrated helium system components. The primary system is a conventional pebble bed reactor with a dynamic central column with an outlet temperature of 900 C providing helium to an intermediate helium to helium heat exchanger (IHX). The outlet of the IHX is input to a three shaft horizontal Brayton Cycle power conversion system. The design constraint used in sizing the plant is based on a factory modularity principle which allows the plant to be assembled 'Lego' style instead of constructed piece by piece. This principle employs space frames which contain the power conversion system that permits the Lego-like modules to be shipped by truck or train to sites. This paper also describes the research that has been conducted at MIT since 1998 on fuel modeling, silver leakage from coated fuel particles, dynamic simulation, MCNP reactor physics modeling and air ingress analysis

  8. Particle flow of ceramic breeder pebble beds in bi-axial compression experiments

    International Nuclear Information System (INIS)

    Hermsmeyer, S.; Reimann, J.

    2002-01-01

    Pebble beds of ceramic material are investigated within the framework of developing solid breeder blankets for future fusion power plants. A thermo-mechanical characterisation of such pebble beds is mandatory for understanding the behaviour of pebble beds, and thus the overall blanket, under fusion environment conditions. The mechanical behaviour of pebble beds is typically explored with uni-axial, bi-axial and tri-axial compression experiments. The latter two types of experiment are particularly revealing since they contain explicitly, beyond a compression behaviour of the bed, information on the conditions for pebble flow, i.e. macroscopic relocation, in the pebble bed. (orig.)

  9. Representation of Solar Capacity Value in the ReEDS Capacity Expansion Model

    Energy Technology Data Exchange (ETDEWEB)

    Sigrin, B. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Sullivan, P. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ibanez, E. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Margolis, R. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2014-03-01

    An important issue for electricity system operators is the estimation of renewables' capacity contributions to reliably meeting system demand, or their capacity value. While the capacity value of thermal generation can be estimated easily, assessment of wind and solar requires a more nuanced approach due to the resource variability. Reliability-based methods, particularly assessment of the Effective Load-Carrying Capacity, are considered to be the most robust and widely-accepted techniques for addressing this resource variability. This report compares estimates of solar PV capacity value by the Regional Energy Deployment System (ReEDS) capacity expansion model against two sources. The first comparison is against values published by utilities or other entities for known electrical systems at existing solar penetration levels. The second comparison is against a time-series ELCC simulation tool for high renewable penetration scenarios in the Western Interconnection. Results from the ReEDS model are found to compare well with both comparisons, despite being resolved at a super-hourly temporal resolution. Two results are relevant for other capacity-based models that use a super-hourly resolution to model solar capacity value. First, solar capacity value should not be parameterized as a static value, but must decay with increasing penetration. This is because -- for an afternoon-peaking system -- as solar penetration increases, the system's peak net load shifts to later in the day -- when solar output is lower. Second, long-term planning models should determine system adequacy requirements in each time period in order to approximate LOLP calculations. Within the ReEDS model we resolve these issues by using a capacity value estimate that varies by time-slice. Within each time period the net load and shadow price on ReEDS's planning reserve constraint signals the relative importance of additional firm capacity.

  10. Fluidized bed calciner

    International Nuclear Information System (INIS)

    Sheely, W.F.

    1986-01-01

    A unique way to convert radioactive scrap into useful nuclear fuel products was developed for the Department of Energy at Hanford. An advanced, fluidized bed calciner is used to convert metallic nitrate scrap or waste solutions into benign, solid and gaseous products. There are broad potential applications of this concept beyond those in the nuclear industry

  11. Nail Bed Injuries

    Science.gov (United States)

    ... All Topics A-Z Videos Infographics Symptom Picker Anatomy Bones Joints Muscles Nerves Vessels Tendons About Hand Surgery What is a Hand Surgeon? What is a Hand Therapist? Media Find a Hand Surgeon Home Anatomy Nail Bed Injuries Email to a friend * required ...

  12. Bed Bug Myths

    Science.gov (United States)

    Learn the truth about bed bugs, such as how easy they are to see with the naked eye, their preferred habitat, whether they transmit diseases, their public health effects, and whether pesticides are the best way to deal with an infestation.

  13. Continuous butyric acid fermentation coupled with REED technology for enhanced productivity

    DEFF Research Database (Denmark)

    Baroi, George Nabin; Skiadas, Ioannis; Westermann, Peter

    strains, C.tyrobutyricum seems the most promising for biological production of butyric acid as it is characterised by higher selectivity and higher tolerance to butyric acid. However, studies on fermentative butyric production from lignocellulosic biomasses are scarce in the international literature...... of continuous fermentation mode and in-situ acids removal by Reverse Enhanced Electro Dialysis (REED) resulted to enhanced sugars consumption rates when 60% PHWS was fermented. Specifically, glucose and xylose consumption rate increased by a factor of 6 and 39, respectively, while butyric acid productivity...

  14. Analysis of Iterated Hard Decision Decoding of Product Codes with Reed-Solomon Component Codes

    DEFF Research Database (Denmark)

    Justesen, Jørn; Høholdt, Tom

    2007-01-01

    Products of Reed-Solomon codes are important in applications because they offer a combination of large blocks, low decoding complexity, and good performance. A recent result on random graphs can be used to show that with high probability a large number of errors can be corrected by iterating...... minimum distance decoding. We present an analysis related to density evolution which gives the exact asymptotic value of the decoding threshold and also provides a closed form approximation to the distribution of errors in each step of the decoding of finite length codes....

  15. Decoding of interleaved Reed-Solomon codes using improved power decoding

    DEFF Research Database (Denmark)

    Puchinger, Sven; Rosenkilde ne Nielsen, Johan

    2017-01-01

    We propose a new partial decoding algorithm for m-interleaved Reed-Solomon (IRS) codes that can decode, with high probability, a random error of relative weight 1 − Rm/m+1 at all code rates R, in time polynomial in the code length n. For m > 2, this is an asymptotic improvement over the previous...... state-of-the-art for all rates, and the first improvement for R > 1/3 in the last 20 years. The method combines collaborative decoding of IRS codes with power decoding up to the Johnson radius....

  16. Systematic Procedure for Integrated Process Operation: Reverse Electro-Enhanced Dialysis (REED) during Lactic Acid Fermentation

    DEFF Research Database (Denmark)

    Prado Rubio, Oscar Andres; Jørgensen, Sten Bay; Jonsson, Gunnar Eigil

    2011-01-01

    The integration of lactic acid fermentation and Reverse Electro-Enhanced Dialysis (REED) is investigated based upon previously developed mathematical models. A goal driven process and operation design procedure is proposed and partially investigated. The conceptual analysis of the processes...... integration shows the need for an additional pH controller in the fermenten A PI controller is implemented and tested. The complete control structure for the integrated system consists of this PI controller in the fermenter plus a previously developed (Prado-Rubio et al., 2010) input resetting control...

  17. Transform Decoding of Reed-Solomon Codes. Volume I. Algorithm and Signal Processing Structure

    Science.gov (United States)

    1982-11-01

    systematic channel co.’e. 1. lake the inverse transform of the r- ceived se, - nee. 2. Isolate the error syndrome from the inverse transform and use... inverse transform is identic l with interpolation of the polynomial a(z) from its n values. In order to generate a Reed-Solomon (n,k) cooce, we let the set...in accordance with the transform of equation (4). If we were to apply the inverse transform of equa- tion (6) to the coefficient sequence of A(z), we

  18. High-radix transforms for Reed-Solomon codes over Fermat primes

    Science.gov (United States)

    Liu, K. Y.; Reed, I. S.; Truong, T. K.

    1977-01-01

    A method is proposed to streamline the transform decoding algorithm for Reed-Solomon (RS) codes of length equal to 2 raised to the power 2n. It is shown that a high-radix fast Fourier transform (FFT) type algorithm with generator equal to 3 on GF(F sub n), where F sub n is a Fermat prime, can be used to decode RS codes of this length. For a 256-symbol RS code, a radix 4 and radix 16 FFT over GF(F sub 3) require, respectively, 30 and 70% fewer modulo F sub n multiplications than the usual radix 2 FFT.

  19. Determination of seven bisphenol analogues in reed and Callitrichaceae by ultra performance liquid chromatography-tandem mass spectrometry.

    Science.gov (United States)

    Lu, Libin; Yang, Yunjia; Zhang, Jing; Shao, Bing

    2014-03-15

    An analytical procedure was developed to simultaneously determine bisphenol S, bisphenol F, bisphenol B, bisphenol A, bisphenol AF, tetrachlorobisphenol A, and tetrabromobisphenol A in reed and Callitrichaceae. Homogenized samples were extracted with acetonitrile and purified using an ENVI™-Carb cartridge followed by an NH2 cartridge. The analytes were separated and quantified by ultra performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS). The recoveries at three fortified levels in reed and Callitrichaceae were 57-108% and 68-106%, respectively, with relative standard deviations of no more than 15% (n=6). The method limits of quantification and detection for the seven bisphenol analogues were 0.005-0.500μg/kg and 0.002-0.150μg/kg, respectively. This method was used to analyze the seven compounds in ten reed and Callitrichaceae samples collected from Zhejiang, China. Copyright © 2014 Elsevier B.V. All rights reserved.

  20. Large-scale management of common reed, Phragmites australis, for paper production: A case study from the Liaohe Delta, China

    DEFF Research Database (Denmark)

    Brix, Hans; Ye, Siyuan; Laws, Edward A.

    2014-01-01

    The largest Phragmites reed field in the world, with a historical area of approximately 1000 km2, is located in the Liaohe Delta in northeastern China. The Phragmites wetlands are extensively managed to maximize the production of reed biomass for the paper industry. Based on satellite remote sens...

  1. Early successional stages of reed Phragmites australis vegetations and its importance for the Bearded Reedling Panurus biarmicus in Oostvaardersplassen, The Netherlands

    NARCIS (Netherlands)

    Beemster, Nico; Troost, Els; Platteeuw, Maarten

    2010-01-01

    A study on Bearded Reed ling Panurus biarmicus feeding habits in combination with a sample-wise breeding bird survey of the marshland zones of the Dutch wetland Oostvaardersplassen shows clear-cut spatial differences in densities and habitat use. The more mature stands of Reed Phragmites australis

  2. 7 CFR 2902.15 - Bedding, bed linens, and towels.

    Science.gov (United States)

    2010-01-01

    ... PROCUREMENT Designated Items § 2902.15 Bedding, bed linens, and towels. (a) Definition. (1) Bedding is that... minimum biobased content is 12 percent and shall be based on the amount of qualifying biobased carbon in..., and silk are not qualifying biobased feedstocks for the purpose of determining the biobased content of...

  3. VA National Bed Control System

    Data.gov (United States)

    Department of Veterans Affairs — The VA National Bed Control System records the levels of operating, unavailable and authorized beds at each VAMC, and it tracks requests for changes in these levels....

  4. Getting Rid of Bed Bugs

    Science.gov (United States)

    ... Directory Planning, Budget and Results Jobs and Internships Headquarters Offices Regional Offices Labs and Research Centers Bed ... to be careful in how you select a company. Related Information Collaborative Strategy on Bed Bugs - highlights ...

  5. Responses to playback of different subspecies songs in the Reed Bunting (Emberiza s. schoeniclus)

    DEFF Research Database (Denmark)

    Matessi, Giuliano; Dabelsteen, Torben; Pilastro, A.

    2000-01-01

    Populations of Reed Buntings Emberiza schoeniclus in the western Palearctic are classified in two major subspecies groups according to morphology: northern migratory schoeniclus and Mediterranean resident intermedia. Songs of the two groups differ mainly in complexity and syllable structure......, with intermedia songs being more complex. We explored the possibilities of song as a subspecies isolating mechanism by testing if male schoeniclus Reed Buntings reacted differently to field playbacks of songs from their own subspecies group, from the foreign subspecies group and from a control species...

  6. Enhanced Nutrients Removal Using Reeds Straw as Carbon Source in a Laboratory Scale Constructed Wetland

    Directory of Open Access Journals (Sweden)

    Tong Wang

    2018-05-01

    Full Text Available The low carbon/nitrogen (C/N ratio and high nitrate content characteristics of agricultural runoff restricted the nitrogen removal in constructed wetlands (CWs. To resolve such problems, the economically- and easily-obtained Phragmites Australis (reeds litters were applied and packed in the surface layer of a surface flow CW as external carbon sources. The results demonstrated that the introduction of the reeds straw increased the C concentration as a result of their decomposition during the CW operation, which will help the denitrification in the ensuing operation of an entire 148 days. The total nitrogen (TN and Chemical Oxygen Demand (COD ( in the effluent reached the peak level of 63.2 mg/L and 83 mg/L at the fourth and the second day, respectively. Subsequently, the pollutants in the CW that were filled with straw decreased rapidly and achieved a stable removal after 13 days of operation. Moreover, the present study showed that the N removal efficiency increased with the increase of the hydraulic retention time (HRT. Under the HRT of four days, the CW presented 74.1 ± 6%, 87.4 ± 6% and 56.0 ± 6% removal for TN, NO3-, and TP, respectively.

  7. Coping with shifting nest predation refuges by European reed Warblers Acrocephalus scirpaceus.

    Directory of Open Access Journals (Sweden)

    Lucyna Halupka

    Full Text Available Predation, the most important source of nest mortality in altricial birds, has been a subject of numerous studies during past decades. However, the temporal dynamics between changing predation pressures and parental responses remain poorly understood. We analysed characteristics of 524 nests of European reed warblers monitored during six consecutive breeding seasons in the same area, and found some support for the shifting nest predation refuge hypothesis. Nest site characteristics were correlated with nest fate, but a nest with the same nest-site attributes could be relatively safe in one season and vulnerable to predation in another. Thus nest predation refuges were ephemeral and there was no between-season consistency in nest predation patterns. Reed warblers that lost their first nests in a given season did not disperse farther for the subsequent reproductive attempt, compared to successful individuals, but they introduced more changes to their second nest sites. In subsequent nests, predation risk remained constant for birds that changed nest-site characteristics, but increased for those that did not. At the between-season temporal scale, individual birds did not perform better with age in terms of reducing nest predation risk. We conclude that the experience acquired in previous years may not be useful, given that nest predation refuges are not stable.

  8. Fault-tolerant conversion between adjacent Reed-Muller quantum codes based on gauge fixing

    Science.gov (United States)

    Quan, Dong-Xiao; Zhu, Li-Li; Pei, Chang-Xing; Sanders, Barry C.

    2018-03-01

    We design forward and backward fault-tolerant conversion circuits, which convert between the Steane code and the 15-qubit Reed-Muller quantum code so as to provide a universal transversal gate set. In our method, only seven out of a total 14 code stabilizers need to be measured, and we further enhance the circuit by simplifying some stabilizers; thus, we need only to measure eight weight-4 stabilizers for one round of forward conversion and seven weight-4 stabilizers for one round of backward conversion. For conversion, we treat random single-qubit errors and their influence on syndromes of gauge operators, and our novel single-step process enables more efficient fault-tolerant conversion between these two codes. We make our method quite general by showing how to convert between any two adjacent Reed-Muller quantum codes \\overline{\\textsf{RM}}(1,m) and \\overline{\\textsf{RM}}≤ft(1,m+1\\right) , for which we need only measure stabilizers whose number scales linearly with m rather than exponentially with m obtained in previous work. We provide the explicit mathematical expression for the necessary stabilizers and the concomitant resources required.

  9. Evaluating the Value of High Spatial Resolution in National Capacity Expansion Models using ReEDS

    Energy Technology Data Exchange (ETDEWEB)

    Krishnan, Venkat; Cole, Wesley

    2016-07-18

    This poster is based on the paper of the same name, presented at the IEEE Power & Energy Society General Meeting, July18, 2016. Power sector capacity expansion models (CEMs) have a broad range of spatial resolutions. This paper uses the Regional Energy Deployment System (ReEDS) model, a long-term national scale electric sector CEM, to evaluate the value of high spatial resolution for CEMs. ReEDS models the United States with 134 load balancing areas (BAs) and captures the variability in existing generation parameters, future technology costs, performance, and resource availability using very high spatial resolution data, especially for wind and solar modeled at 356 resource regions. In this paper we perform planning studies at three different spatial resolutions - native resolution (134 BAs), state-level, and NERC region level - and evaluate how results change under different levels of spatial aggregation in terms of renewable capacity deployment and location, associated transmission builds, and system costs. The results are used to ascertain the value of high geographically resolved models in terms of their impact on relative competitiveness among renewable energy resources.

  10. Geomechanics of bedded salt

    International Nuclear Information System (INIS)

    Serata, S.; Milnor, S.W.

    1979-01-01

    Creep data from the literature search is reinterpreted by SGI, resulting in a better understanding of the temperature and stress state dependence of the octahedral creep rate and the octahedral shear strength. The concept of a transition strength between the elastic and the plastic states is in agreement with the data. The elastic and rheological properties of salt are described, and a set of constitutive equations is presented. The dependence of material properties on parameters such as temperature is considered. Findings on the permeability of salt are summarized, and the in-situ behavior of openings in bedded salt is described based on extensive engineering experience. A stress measuring system utilizing a finite element computer code is discussed. Geological factors affecting the stability of salt openings are considered, and the Stress Control Technique for designing stable openings in bedded salt formations is explained

  11. Does conspicuous colouration of Magpies Pica pica influence aggressive behaviour in nesting Great Reed Warblers Acrocephalus arundinaceus?

    Czech Academy of Sciences Publication Activity Database

    Trnka, A.; Požgayová, Milica

    2017-01-01

    Roč. 64, č. 1 (2017), s. 108-111 ISSN 0006-3657 Institutional support: RVO:68081766 Keywords : Magpies Pica pica * Great Reed Warblers Acrocephalus arundinaceus Subject RIV: EG - Zoology OBOR OECD: Ornithology Impact factor: 0.925, year: 2016

  12. Integrated Canada-U.S. Power Sector Modeling with the Regional Energy Deployment System (ReEDS)

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, A.; Eurek, K.; Mai, T.; Perry, A.

    2013-02-01

    The electric power system in North America is linked between the United States and Canada. Canada has historically been a net exporter of electricity to the United States. The extent to which this remains true will depend on the future evolution of power markets, technology deployment, and policies. To evaluate these and related questions, we modify the Regional Energy Deployment System (ReEDS) model to include an explicit representation of the grid-connected power system in Canada to the continental United States. ReEDS is unique among long-term capacity expansion models for its high spatial resolution and statistical treatment of the impact of variable renewable generation on capacity planning and dispatch. These unique traits are extended to new Canadian regions. We present example scenario results using the fully integrated Canada-U.S. version of ReEDS to demonstrate model capabilities. The newly developed, integrated Canada-U.S. ReEDS model can be used to analyze the dynamics of electricity transfers and other grid services between the two countries under different scenarios.

  13. Giant reed (Arundo donax L. for biogas production: land use saving and nitrogen utilisation efficiency compared with arable crops

    Directory of Open Access Journals (Sweden)

    Federico Dragoni

    2015-12-01

    Full Text Available Aiming to improve the sustainability of biogas supply chains, the research for alternative feedstocks is a key issue and giant reed (Arundo donax L. is a promising no-food crop to be used in anaerobic digestion. In fact, giant reed is a perennial species characterised by low nutrient requirements and is able to provide promising biogas yields. Its suitability for anaerobic digestion is influenced by harvest time, since plant characteristics vary noticeably along the season. Moreover, ensiling is a storage technique that can assure a good preservation of the biomass over time, but also influence the methane yields. Therefore, the aim of this study was to assess the suitability for biogas production of giant reed silage, according to different cutting regimes, and to evaluate the efficiency in saving land and nitrogen for fuelling biogas plants, in comparison with maize and two sorghum varieties. Methane yields per hectare (Nm3 CH4 ha–1 were determined by multiplying the biochemical methane potential of each substrate by the aboveground biomass of the corresponding crop. The land use coefficient (LU, namely the land needed to fuel one kW power (ha kWe–1, was calculated from the estimated methane yields per hectare. Finally, nitrogen utilisation efficiency (NUtE, which is the ratio between the estimated methane yield and the nitrogen uptake per hectare (Nm3 CH4 kgN–1, was determined for each crop species and according to the harvest time and frequency of giant reed. Overall, a good suitability for ensiling was observed in giant reed. When harvested in September, the crop yielded about 9900 Nm3 CH4 ha–1, while in double harvest systems biomethane was about 12,000 Nm3 CH4 ha–1, +35% and +70% than maize and sorghum respectively. Moreover, giant reed under double harvest management was the most land-conservative option, as LU was about 0.22 ha kWe–1, while in annual crops it was about 0.35 ha kWe–1. The higher NUtE was observed in single

  14. A low tritium hydride bed inventory estimation technique

    Energy Technology Data Exchange (ETDEWEB)

    Klein, J.E.; Shanahan, K.L.; Baker, R.A. [Savannah River National Laboratory, Aiken, SC (United States); Foster, P.J. [Savannah River Nuclear Solutions, Aiken, SC (United States)

    2015-03-15

    Low tritium hydride beds were developed and deployed into tritium service in Savannah River Site. Process beds to be used for low concentration tritium gas were not fitted with instrumentation to perform the steady-state, flowing gas calorimetric inventory measurement method. Low tritium beds contain less than the detection limit of the IBA (In-Bed Accountability) technique used for tritium inventory. This paper describes two techniques for estimating tritium content and uncertainty for low tritium content beds to be used in the facility's physical inventory (PI). PI are performed periodically to assess the quantity of nuclear material used in a facility. The first approach (Mid-point approximation method - MPA) assumes the bed is half-full and uses a gas composition measurement to estimate the tritium inventory and uncertainty. The second approach utilizes the bed's hydride material pressure-composition-temperature (PCT) properties and a gas composition measurement to reduce the uncertainty in the calculated bed inventory.

  15. Petrology and geochemistry of samples from bed-contact zones in Tunnel Bed 5, U12g-Tunnel, Nevada Test Site

    International Nuclear Information System (INIS)

    Connolly, J.R.; Keil, K.; Mansker, W.L.; Allen, C.C.; Husler, J.; Lowy, R.; Fortney, D.R.; Lappin, A.R.

    1984-10-01

    This report summarizes the detailed geologic characterization of samples of bed-contact zones and surrounding nonwelded bedded tuffs, both within Tunnel Bed 5, that are exposed in the G-Tunnel complex beneath Rainier Mesa on the Nevada Test Site (NTS). Original planning studies treated the bed-contact zones in Tunnel Bed 5 as simple planar surfaces of relatively high permeability. Detailed characterization, however, indicates that these zones have a finite thickness, are depositional in origin, vary considerably over short vertical and horizontal distances, and are internally complex. Fluid flow in a sequence of nonwelded zeolitized ash-flow or bedded tuffs and thin intervening reworked zones appears to be a porous-medium phenomenon, regardless of the presence of layering. There are no consistent differences in either bulk composition or detailed mineralogy between bedded tuffs and bed-contact zones in Tunnel Bed 5. Although the original bulk composition of Tunnel Bed 5 was probably peralkaline, extensive zeolitization has resulted in a present peraluminous bulk composition of both bedded tuffs and bed-contact zones. The major zeolite present, clinoptilolite, is intermediate (Ca:K:Na = 26:35:39) and effectively uniform in composition. This composition is similar to that of clinoptilolite from the tuffaceous beds of Calico Hills above the static water level in hole USW G-1, but somewhat different from that reported for zeolites from below the static water level in USW G-2. Tunnel Bed 5 also contains abundant hydrous manganese oxides. The similarity in composition of the clinoptilolites from Tunnel Bed 5 and those above the static water level at Yucca Mountain indicates that many of the results of nuclide-migration experiments in Tunnel Bed 5 would be transferrable to zeolitized nonwelded tuffs above the static water level at Yucca Mountain

  16. On the heat transfer in packed beds

    International Nuclear Information System (INIS)

    Sordon, G.

    1988-09-01

    The design of a fusion reactor blanket concept based on a bed of lithium containing ceramic pebbles or a mixture of ceramic and beryllium pebbles demands the knowledge of the effective thermal conductivity of pebble beds, including beds formed by a binary mixture of high conducting metallic pebbles and poorly conducting pebbles. In this work, binary mixtures of spheres of same diameter and different conductivities as well as beds formed by one type of spheres were investigated. The experimental apparatus consists of a stainless steel cylinder with a heating rod along the symmetry axis. Experiments with stagnant and flowing gas were performed. The pebbles were of Al 2 O 3 (diameter = 1, 2, 4 mm), of Li 4 SO 4 (diameter = 0.5 mm) of Al (diameter = 2 mm) and of steel (diameter = 2, 4 mm). Experimental values of the thermal conductivity and of the wall heat transfer coefficient are compared with the predicted ones. Modifications of already existing models were suggested. (orig.) [de

  17. Coal Bed Methane Primer

    Energy Technology Data Exchange (ETDEWEB)

    Dan Arthur; Bruce Langhus; Jon Seekins

    2005-05-25

    During the second half of the 1990's Coal Bed Methane (CBM) production increased dramatically nationwide to represent a significant new source of income and natural gas for many independent and established producers. Matching these soaring production rates during this period was a heightened public awareness of environmental concerns. These concerns left unexplained and under-addressed have created a significant growth in public involvement generating literally thousands of unfocused project comments for various regional NEPA efforts resulting in the delayed development of public and fee lands. The accelerating interest in CBM development coupled to the growth in public involvement has prompted the conceptualization of this project for the development of a CBM Primer. The Primer is designed to serve as a summary document, which introduces and encapsulates information pertinent to the development of Coal Bed Methane (CBM), including focused discussions of coal deposits, methane as a natural formed gas, split mineral estates, development techniques, operational issues, producing methods, applicable regulatory frameworks, land and resource management, mitigation measures, preparation of project plans, data availability, Indian Trust issues and relevant environmental technologies. An important aspect of gaining access to federal, state, tribal, or fee lands involves education of a broad array of stakeholders, including land and mineral owners, regulators, conservationists, tribal governments, special interest groups, and numerous others that could be impacted by the development of coal bed methane. Perhaps the most crucial aspect of successfully developing CBM resources is stakeholder education. Currently, an inconsistent picture of CBM exists. There is a significant lack of understanding on the parts of nearly all stakeholders, including industry, government, special interest groups, and land owners. It is envisioned the Primer would being used by a variety of

  18. Infant's bed climate and bedding in the Japanese home.

    Science.gov (United States)

    Nakamura Ikeda, Rie; Fukai, Kiyoko; Okamoto Mizuno, Kazue

    2012-06-01

    to assess the bed climate of infants in their homes in Japan. descriptive, exploratory, non-experimental research design. the data were collected at the participants' homes under normal circumstances. nineteen healthy infants between the ages of two and five months. Their mothers, who joined a parenting class organised by a maternity clinic in Okayama, Japan, consented to participate in this study. we visited the infants' homes and interviewed their mothers concerning the types and use of bedding. The temperature and relative humidity of the bed climate at the back and foot of the bedding, and in the room were measured every minute for four consecutive days. Differences among the bed climates measured during three seasons (spring, summer, and autumn) were assessed by one-way analysis of variance. The bed temperature was higher for infants than for adults. No significant difference in temperature was noted among the three seasons. The bed temperature was about 36.0°C when waterproof sheets and futon mattresses for children or adult were used. The average relative humidity of the bed climate at the back was highest in summer, followed by that in spring and autumn; the differences were significant. The use of waterproof sheets and futon mattresses for children in summer increased the relative humidity to 80% or more. The use of infant beds, sunoko drainboards, and cotton futon mattresses in summer was effective in reducing the bed humidity. these results suggest that nurse-midwives should advise the parents on comfortable bed climates for their infants, as well as how to select and use bedding for them. Copyright © 2010 Elsevier Ltd. All rights reserved.

  19. Particle bed reactor modeling

    Science.gov (United States)

    Sapyta, Joe; Reid, Hank; Walton, Lew

    The topics are presented in viewgraph form and include the following: particle bed reactor (PBR) core cross section; PBR bleed cycle; fuel and moderator flow paths; PBR modeling requirements; characteristics of PBR and nuclear thermal propulsion (NTP) modeling; challenges for PBR and NTP modeling; thermal hydraulic computer codes; capabilities for PBR/reactor application; thermal/hydralic codes; limitations; physical correlations; comparison of predicted friction factor and experimental data; frit pressure drop testing; cold frit mask factor; decay heat flow rate; startup transient simulation; and philosophy of systems modeling.

  20. Fluidised bed cereal cooking

    International Nuclear Information System (INIS)

    Jenkins, Simon Anthony

    2002-01-01

    Man has been cooking food for thousands of years for a number of reasons: to improve flavour and palatability, sterilise, increase digestibility, improve texture and colour. Increasingly more advanced techniques are employed today in food production plants to engineer foods with many different properties. With this in mind manufacturers are constantly seeking to improve processing techniques and apply new or different technologies (such as microwaves, RF and extrusion) to develop foods with new properties (like puffed texture starches) and to increase process efficiencies (energy efficiency, water reduction). This thesis reports on work undertaken to demonstrate the potential to achieve high temperature starch conversion of whole wheat grains in a fluidised bed, thereby reducing the amount of water required and processing time. Specifically, wheat from the farm at 14% water content is cooked in a fluidised bed. The fluidised bed heats the wheat quickly by convective heating. In addition, energy can be delivered directly to the grain by microwave heating during fluidisation. Degree of starch conversion is determined by measuring the reduction in size of endotherm of reaction as observed by Differential Scanning Calorimetry. The fluidising gas, processing temperature and starting moisture content were varied in order to investigate their effect on the cooking process. A mathematical model based on energy and species concentration equations was developed to help understand the internal grain processes. The model coupled the thermal energy equation with water diffusion. The effect of water evaporation was represented as a thermal sink in the energy equation. Popular kinetic models from literature were adapted to predict the degree of starch conversion. The model gives solutions consistent with experimental data and physical intuition. A commercial computational fluid dynamics package was used to study simple airflow and particle tracks in the fluidisation column. A

  1. Experimental investigations on friction laws and dryout heat flux of particulate beds packed with multi-size spheres and irregular particles

    International Nuclear Information System (INIS)

    Li, Liangxing; Ma, Weimin

    2011-01-01

    This paper is concerned with reducing uncertainty in quantification of debris bed coolability in a hypothetical severe accident of light water reactors (LWRs). A test facility named POMECO-FL is constructed to investigate the friction laws of adiabatic single and two-phase flow in a particulate bed packed with multi-size spheres or irregular particles. The same types of particles were then loaded in the test section of the POMECO-HT facility to obtain the dryout heat flux of the volumetrically heated particulate bed. The POMECO-HT facility features a high power capacity (up to 2.1 MW/m 2 ) which enables coolability study on particulate bed with broad variations in porosity and particle diameters under both top-flooding and bottom-injection conditions. The results show that given the effective particle diameter obtained from single-phase flow through the packed bed with multi-size spheres or irregular particles, both the pressure drop and the dryout heat flux of two-phase flow through the bed can be predicted by the Reed model. The bottom injection of coolant increases the dryout heat flux significantly. Meanwhile, the elevation of the dryout position is moving upwards with increasing bottom-injection flowrate. The experimental data provides insights for interpretation of debris bed coolability, as well as high-quality data for validation of the coolability analysis models and codes. (author)

  2. Permeability of granular beds emplaced in vertical drill holes

    International Nuclear Information System (INIS)

    Griffiths, S.K.; Morrison, F.A. Jr.

    1979-01-01

    To determine the permeabilities of granular materials emplaced in vertical drill holes used for underground nuclear tests, an experiment at the USDOE Nevada Test Site (NTS) was conducted. As the hole is being filled, falling material increases pressure above and within the granular beds beneath. When the filling operation starts or stops, a transient pressure response occurs within the beds; measurements of this response in beds of various compositions were made. The permeabilities after emplacement were found by matching analytical predictions of the response to these data. This information is useful in assuring the containment of nuclear tests conducted in such drill holes

  3. The bedding of laboratory animals as a source of airborne contaminants.

    Science.gov (United States)

    Kaliste, E; Linnainmaa, M; Meklin, T; Torvinen, E; Nevalainen, A

    2004-01-01

    In work environments with laboratory animals, the bedding of animals binds the excreta as well as other compounds originating from the animals and their environment. These may be generated into the ambient air when the personnel handle bedding in different procedures. This study compares the dustiness of different types of six clean and four soiled beddings from rat or mouse cages. The dust generation of clean bedding varied from beddings decreased, increased or stayed the same, depending on the type of bedding and animal species. A decrease in dustiness was, however, more common. The levels in the soiled beddings varied from bedding, the contents of bedding used in mouse, rat or rabbit cages were analysed for mesophilic bacteria and fungi, mycobacteria and endotoxins. All of these contaminants were variably found in the bedding samples, the maximal concentrations for bacteria were >6 500 000 colony-forming units (cfu)/g, for fungi 212 000 cfu/g, and for endotoxins 6500 ng/g (81 000 EU/g). The results showed that the bedding of laboratory animals may contain biologically effective compounds, and that these may be distributed into the ambient air depending on the characteristics of the bedding material. The dustiness of different bedding types is an important factor affecting the amount and quality of the occupational exposure of the personnel to airborne contaminants.

  4. Fast decoding techniques for extended single-and-double-error-correcting Reed Solomon codes

    Science.gov (United States)

    Costello, D. J., Jr.; Deng, H.; Lin, S.

    1984-01-01

    A problem in designing semiconductor memories is to provide some measure of error control without requiring excessive coding overhead or decoding time. For example, some 256K-bit dynamic random access memories are organized as 32K x 8 bit-bytes. Byte-oriented codes such as Reed Solomon (RS) codes provide efficient low overhead error control for such memories. However, the standard iterative algorithm for decoding RS codes is too slow for these applications. Some special high speed decoding techniques for extended single and double error correcting RS codes. These techniques are designed to find the error locations and the error values directly from the syndrome without having to form the error locator polynomial and solve for its roots.

  5. RAID-6 reed-solomon codes with asymptotically optimal arithmetic complexities

    KAUST Repository

    Lin, Sian-Jheng

    2016-12-24

    In computer storage, RAID 6 is a level of RAID that can tolerate two failed drives. When RAID-6 is implemented by Reed-Solomon (RS) codes, the penalty of the writing performance is on the field multiplications in the second parity. In this paper, we present a configuration of the factors of the second-parity formula, such that the arithmetic complexity can reach the optimal complexity bound when the code length approaches infinity. In the proposed approach, the intermediate data used for the first parity is also utilized to calculate the second parity. To the best of our knowledge, this is the first approach supporting the RAID-6 RS codes to approach the optimal arithmetic complexity.

  6. Hydrodynamic cavitation as a novel pretreatment approach for bioethanol production from reed.

    Science.gov (United States)

    Kim, Ilgook; Lee, Ilgyu; Jeon, Seok Hwan; Hwang, Taewoon; Han, Jong-In

    2015-09-01

    In this study, hydrodynamic cavitation (HC) was employed as a physical means to improve alkaline pretreatment of reed. The HC-assisted alkaline pretreatment was undertaken to evaluate the influence of NaOH concentration (1-5%), solid-to-liquid ratio (5-15%), and reaction time (20-60 min) on glucose yield. The optimal condition was found to be 3.0% NaOH at solid-to-liquid (S/L) ratio of 11.8% for 41.1 min, which resulted in the maximum glucose yield of 326.5 g/kg biomass. Furthermore, simultaneous saccharification and fermentation (SSF) was conducted to assess the ethanol production. An ethanol concentration of 25.9 g/L and ethanol yield of 90% were achieved using batch SSF. These results clearly demonstrated HC system can be indeed a promising pretreatment tool for lignocellulosic bioethanol production. Copyright © 2015 Elsevier Ltd. All rights reserved.

  7. The Giant Reed as an energy crop: assessing the energy requirements within its supply chain

    DEFF Research Database (Denmark)

    Rodias, Efthymis; Busato, P.; Bochtis, Dionysis

    2013-01-01

    Biomass energy is one form of renewable energy sources that are in the core of interesting for many researchers. There many different biomass sources that can be exploited for energy production, such as crop residues, waste materials, forestry residues and energy crops. Regarding energy crops......, there are many different types of crops significantly varies in terms of energy potential yields, production and provision methods, etc. To this end, a thoroughly assessment of the energy inputs and outputs of each potential energy crop is necessary. In this paper, the Giant Reed is evaluated energetically...... as a potential energy crop. The assessment regards a 10 year period. The considered energy elements include direct inputs (e.g. fuel consumption) as well as indirect inputs (e.g. embodied energy of materials and machinery). According to the results, the balance between the estimated total energy input...

  8. Mitigation of greenhouse gas emissions from reed canary grass in paludiculture: effect of groundwater level

    DEFF Research Database (Denmark)

    Karki, Sandhya; Elsgaard, Lars; Audet, Joachim

    2014-01-01

    below the soil surface. Gross primary production (GPP) was estimated from the above ground biomass yield. Results The mean dry biomass yield across all water table treatments was 6 Mg ha−1 with no significant differences between the treatments. Raising the GWL to the surface decreased both the net...... of peatlands grown with reed canary grass (RCG) and rewetted to various extents. Methods Gas fluxes of CO2, methane (CH4) and nitrous oxide (N2O) were measured with a static chamber technique for 10 months from mesocosms sown with RCG and manipulated to ground water levels (GWL) of 0, −10, −20, −30 and −40 cm...... The results showed that a reduction in total GHG emission can be achieved without losing the productivity of newly established RCG when GWL is maintained close to the surface. Further studies should address the practical constrains and long-term productivity of RCG cultivation in rewetted peatlands....

  9. Primary production in a shallow water lake with special reference to a reed swamp

    International Nuclear Information System (INIS)

    Andersen, F.Oe.

    1976-01-01

    Phytoplankton gross primary production ( 14 C method) in the shallow, eutrophic Danish Lake Arresoe in 1973 was 980 g C m -2 . Calculated net primary production was near zero. Macrophyte net primary production was measured by harvesting the maximum biomass, and above ground values were between 420 and 1325 g ash free dry wt m -2 , while below ground values were between 2480 and 8570 g ash free dry wt m -2 . The reed swamps were mapped on aerial photographs, and the composition of the macrophyte vegetation was determined. A comparison of macrophyte vegetation in 1944 and 1972 showed a reduction in species diversity, especially of submerged species. The seasonal variations in physical and chemical data indicated strong eutrophication in Arresoe. (author)

  10. Sensory systems for a control rod position using reed switches for the integral reactor

    International Nuclear Information System (INIS)

    Yu, J. Y.; Choi, S.; Kim, J. H.; Lee, D. J.

    2007-01-01

    The system-integrated modular advanced reactor (SMART) currently under development at the Korea Atomic Energy Research Institute is being designed with a soluble boron free operation and the use of nuclear heating for the reactor start-up. These design features require a Control Element Drive Mechanism (CEDM) for the SMART to have a fine-step movement capability as well as a high reliability for a fine reactivity control. Also the reliability and accuracy of the information for the control rod position is very important to the reactor safety as well as the design of the core protection system. The position indicator is classified as a Class 1E component because the rod position signal of the position indicator is used in the safety related systems. Therefore it will be separated from the control systems to the extent that a failure of any single control system component of a channel and shall have sufficient independence, redundancy, and testability to perform its safety functions assuming a single failure. The position indicator is composed of a permanent magnet, reed switches and a voltage divider. Four independent position indicators around the upper pressure housing provide an indication of the position of a control rod comprising of a permanent magnet with a magnetic field concentrator which moves with the extension shaft connected to the control rod. The zigzag arranged reed switches are positioned along a line parallel to the path of the movement of the permanent magnet and it is activated selectively when the permanent magnet passes by. A voltage divider electrically connected to the reed switches provides a signal commensurate with the position of the control rod. The signal may then be transmitted to a position indicating device. In order to monitor the operating condition of the rotary step motor of CEDM, the angular position detector was installed at the top of the rotary step motor by means of connecting between the planetary gear and the rotating

  11. Measurements on very small single crystals of NdFeB using a vibrating reed magnetometer

    International Nuclear Information System (INIS)

    Richter, H.J.; Hempel, K.A.; Verhoef, R.

    1988-01-01

    Nd 2 Fe 14 B single crystals with magnetic moments ranging from 1.6 x 10 -8 Acm 2 to 9.5 x 10 -7 Acm 2 are measured using the ultra high sensitivity vibrating reed magnetometer. The hysteresis loops are compared to those of BaFe 12 O 19 single crystals. It turns out that the magnetization reversal of the Nd 2 Fe 14 B samples is similar to that of BaFe 12 O 19 single crystals if the ferrite samples are considerably bigger in size. This does not hold for bigger Nd 2 Fe 14 B particles where stronger domain wall pinning is observed. For very small grains of Nd 2 Fe 14 B there is still evidence of domain wall processes while for BaFe 12 O 19 grains of the same size true single domain behaviour can be observed

  12. Effect of reed canary grass cultivation on greenhouse gas emission from peat soil at controlled rewetting

    DEFF Research Database (Denmark)

    Karki, Sandhya; Elsgaard, Lars; Lærke, Poul Erik

    2015-01-01

    Cultivation of bioenergy crops in rewetted peatland (paludiculture) is considered as a possible land use option to mitigate greenhouse gas (GHG) emissions. However, bioenergy crops like reed canary grass (RCG) can have a complex influence on GHG fluxes. Here we determined the effect of RCG...... and bare soil were measured at weekly to fortnightly intervals with static chamber techniques for a period of 1 year. Cultivation of RCG increased both ER and CH4 emissions, but decreased the N2O emissions. The presence of RCG gave rise to 69, 75 and 85% of total ER at −20, −10 and 0 cm GWL, respectively...... from ER were obviously the dominant RCG-derived GHG flux, but above-ground biomass yields, and preliminary measurements of gross photosynthetic production, showed that ER could be more than balanced due to the photosynthetic uptake of CO2 by RCG. Our results support that RCG cultivation could be a good...

  13. Novel Polynomial Basis with Fast Fourier Transform and Its Application to Reed-Solomon Erasure Codes

    KAUST Repository

    Lin, Sian-Jheng

    2016-09-13

    In this paper, we present a fast Fourier transform (FFT) algorithm over extension binary fields, where the polynomial is represented in a non-standard basis. The proposed Fourier-like transform requires O(h lg(h)) field operations, where h is the number of evaluation points. Based on the proposed Fourier-like algorithm, we then develop the encoding/ decoding algorithms for (n = 2m; k) Reed-Solomon erasure codes. The proposed encoding/erasure decoding algorithm requires O(n lg(n)), in both additive and multiplicative complexities. As the complexity leading factor is small, the proposed algorithms are advantageous in practical applications. Finally, the approaches to convert the basis between the monomial basis and the new basis are proposed.

  14. Sorghum-sudangrass responses to nitrogen and tillage following polyphenol-containing legumes, alfalfa, reed canarygrass, and kale

    Science.gov (United States)

    The collective effects of protein-binding polyphenols (PBP), preceding forage type, tillage, and fertilizer N on soil NO3-N production, N uptake, and dry matter yield (DMY) of N-demanding crops such as sorghum-sudangrass [SS, Sorghum bicolor (L.) Moench x S. sudanese Piper] are poorly understood. Th...

  15. Fluidized bed boiler feed system

    Science.gov (United States)

    Jones, Brian C.

    1981-01-01

    A fluidized bed boiler feed system for the combustion of pulverized coal. Coal is first screened to separate large from small particles. Large particles of coal are fed directly to the top of the fluidized bed while fine particles are first mixed with recycled char, preheated, and then fed into the interior of the fluidized bed to promote char burnout and to avoid elutriation and carryover.

  16. Contrasting results from GWAS and QTL mapping on wing length in great reed warblers.

    Science.gov (United States)

    Hansson, Bengt; Sigeman, Hanna; Stervander, Martin; Tarka, Maja; Ponnikas, Suvi; Strandh, Maria; Westerdahl, Helena; Hasselquist, Dennis

    2018-04-15

    A major goal in evolutionary biology is to understand the genetic basis of adaptive traits. In migratory birds, wing morphology is such a trait. Our previous work on the great reed warbler (Acrocephalus arundinaceus) shows that wing length is highly heritable and under sexually antagonistic selection. Moreover, a quantitative trait locus (QTL) mapping analysis detected a pronounced QTL for wing length on chromosome 2, suggesting that wing morphology is partly controlled by genes with large effects. Here, we re-evaluate the genetic basis of wing length in great reed warblers using a genomewide association study (GWAS) approach based on restriction site-associated DNA sequencing (RADseq) data. We use GWAS models that account for relatedness between individuals and include covariates (sex, age and tarsus length). The resulting association landscape was flat with no peaks on chromosome 2 or elsewhere, which is in line with expectations for polygenic traits. Analysis of the distribution of p-values did not reveal biases, and the inflation factor was low. Effect sizes were however not uniformly distributed on some chromosomes, and the Z chromosome had weaker associations than autosomes. The level of linkage disequilibrium (LD) in the population decayed to background levels within c. 1 kbp. There could be several reasons to why our QTL study and GWAS gave contrasting results including differences in how associations are modelled (cosegregation in pedigree vs. LD associations), how covariates are accounted for in the models, type of marker used (multi- vs. biallelic), difference in power or a combination of these. Our study highlights that the genetic architecture even of highly heritable traits is difficult to characterize in wild populations. © 2018 John Wiley & Sons Ltd.

  17. The use of reed canary grass and giant miscanthus in the phytoremediation of municipal sewage sludge.

    Science.gov (United States)

    Antonkiewicz, Jacek; Kołodziej, Barbara; Bielińska, Elżbieta Jolanta

    2016-05-01

    The application of municipal sewage sludge on energy crops is an alternative form of recycling nutrients, food materials, and organic matter from waste. Municipal sewage sludge constitutes a potential source of heavy metals in soil, which can be partially removed by the cultivation of energy crops. The aim of the research was to assess the effect of municipal sewage sludge on the uptake of heavy metals by monocotyledonous energy crops. Sewage sludge was applied at doses of 0, 10, 20, 40, and 60 Mg DM · ha(-1) once, before the sowing of plants. In a 6-year field experiment, the effect of four levels of fertilisation with sewage sludge on the uptake of heavy metals by two species of energy crops, reed canary grass (Phalaris arundinacea L.) of 'Bamse' cultivar and giant miscanthus (Miscanthus × giganteus GREEF et DEU), was analysed. It was established that the increasing doses of sewage sludge had a considerable effect on the increase in biomass yield from the tested plants. Due to the increasing doses of sewage sludge, a significant increase in heavy metals content in the energy crops was recorded. The heavy metal uptake with the miscanthus yield was the highest at a dose of 20 Mg DM · ha(-1), and at a dose of 40 Mg DM · ha(-1) in the case of reed canary grass. Research results indicate that on account of higher yields, higher bioaccumulation, and higher heavy metal uptake, miscanthus can be selected for the remediation of sewage sludge.

  18. Walter Reed Army Medical Center's Internet-based electronic health portal.

    Science.gov (United States)

    Abbott, Kevin C; Boocks, Carl E; Sun, Zhengyi; Boal, Thomas R; Poropatich, Ronald K

    2003-12-01

    Use of the World Wide Web (WWW) and electronic media to facilitate medical care has been the subject of many reports in the popular press. However, few reports have documented the results of implementing electronic health portals for essential medical tasks, such as prescription refills and appointments. At Walter Reed Army Medical Center, "Search & Learn" medical information, Internet-based prescription refills and patient appointments were established in January 2001. A multiphase retrospective analysis was conducted to determine the use of the "Search & Learn" medical information and the relative number of prescription refills and appointments conducted via the WWW compared with conventional methods. From January 2001 to May 2002, there were 34,741 refills and 819 appointments made over the Internet compared with 2,275,112 refills and approximately 500,000 appointments made conventionally. WWW activity accounted for 1.52% of refills and 0.16% of appointments. There was a steady increase in this percentage over the time of the analysis. In April of 2002, the monthly average of online refills had risen to 4.57% and online appointments were at 0.27%. Online refills were projected to account for 10% of all prescriptions in 2 years. The "Search & Learn" medical information portion of our web site received 147,429 unique visits during this same time frame, which was an average of 326 visitors per day. WWW-based methods of conducting essential medical tasks accounted for a small but rapidly increasing percentage of total activity at Walter Reed Army Medical Center. Subsequent phases of analysis will assess demographic and geographic factors and aid in the design of future systems to increase use of the Internet-based systems.

  19. Comparison of Two Phase Pressure Drop Models in 1-D Top Flooded Debris Bed

    International Nuclear Information System (INIS)

    Lee, Moon Eon; Park, Jin Ho; Kim, Eun ho; Park, Hyun Sun

    2016-01-01

    The dry out of coolant inside debris bed can be considered as the limitation of cooling in the conservative point of view and the heat flux through whole bed at the situation is named as Dryout Heat Flux (DHF). The modeling of DHF for debris bed started from early 1980s by several researchers. It is known that DHF mainly occurs by hydrodynamic limitation inside porous media. Therefore, there have been following attempts to capture flow resistance in porous media, precisely. Up to date, although there are about seven pressure drop models available in literatures, it is hard to find comparison of those models with a wide range of DHF experimental data. The one attempt[9] was conducted in 2013, but due to lack of consideration of the capillary pressure in his work, the DHF values that he calculated seem to be underestimated, especially in the range of the small particle diameter cases. In this research, the importance of capillary pressure in the comparison of pressure drop model with experimental data was checked and model selection among pressure drop models for the DHF calculation was also conducted. The model comparison with 108 experimental data from various conditions has been conducted and the Schmidt model shows the best agreement to the experimental data although Reed, Rahman model also show similar results.

  20. Comparison of Two Phase Pressure Drop Models in 1-D Top Flooded Debris Bed

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Moon Eon; Park, Jin Ho; Kim, Eun ho; Park, Hyun Sun [POSTECH, Pohang (Korea, Republic of)

    2016-05-15

    The dry out of coolant inside debris bed can be considered as the limitation of cooling in the conservative point of view and the heat flux through whole bed at the situation is named as Dryout Heat Flux (DHF). The modeling of DHF for debris bed started from early 1980s by several researchers. It is known that DHF mainly occurs by hydrodynamic limitation inside porous media. Therefore, there have been following attempts to capture flow resistance in porous media, precisely. Up to date, although there are about seven pressure drop models available in literatures, it is hard to find comparison of those models with a wide range of DHF experimental data. The one attempt[9] was conducted in 2013, but due to lack of consideration of the capillary pressure in his work, the DHF values that he calculated seem to be underestimated, especially in the range of the small particle diameter cases. In this research, the importance of capillary pressure in the comparison of pressure drop model with experimental data was checked and model selection among pressure drop models for the DHF calculation was also conducted. The model comparison with 108 experimental data from various conditions has been conducted and the Schmidt model shows the best agreement to the experimental data although Reed, Rahman model also show similar results.

  1. Management bedding : vrijloopstal met composterende bedding van houtsnippers

    NARCIS (Netherlands)

    Boer, de H.C.; Wiersma, M.; Galama, P.J.; Szanto, G.L.

    2015-01-01

    In de vrijloopstal liggen de koeien meestal op een organische bedding en scheiden daar mest (feces en urine) uit. Om de bedding voldoende droog en schoon te houden wordt er regelmatig nieuw strooisel aangevoerd en wordt de toplaag bewerkt. Op basis van onderzoek- en praktijkervaringen tot nu toe

  2. Fluidized bed incineration of transuranic contaminated waste

    International Nuclear Information System (INIS)

    Ziegler, D.L.; Johnson, A.J.

    1978-01-01

    A 9 kg/hr pilot scale fluidized bed incinerator is now being used for burning various types of radioactive waste at Rocky Flats Plant. General solid combustible waste containing halogenated materials is burned in a fluidized bed of sodium carbonate for in situ neutralization of thermally generated acidic gases. A variety of other production related materials has been burned in the incinerator, including ion exchange resin, tributyl phosphate solutions, and air filters. Successful operation of the pilot plant incinerator has led to the design and construction of a production site unit to burn 82 kg/hr of plant generated waste. Residues from incinerator operations will be processed into glass buttons utilizing a vitrification plant now under development

  3. Core homogenization method for pebble bed reactors

    International Nuclear Information System (INIS)

    Kulik, V.; Sanchez, R.

    2005-01-01

    This work presents a core homogenization scheme for treating a stochastic pebble bed loading in pebble bed reactors. The reactor core is decomposed into macro-domains that contain several pebble types characterized by different degrees of burnup. A stochastic description is introduced to account for pebble-to-pebble and pebble-to-helium interactions within a macro-domain as well as for interactions between macro-domains. Performance of the proposed method is tested for the PROTEUS and ASTRA critical reactor facilities. Numerical simulations accomplished with the APOLLO2 transport lattice code show good agreement with the experimental data for the PROTEUS reactor facility and with the TRIPOLI4 Monte Carlo simulations for the ASTRA reactor configuration. The difference between the proposed method and the traditional volume-averaged homogenization technique is negligible while only one type of fuel pebbles present in the system, but it grows rapidly with the level of pebble heterogeneity. (authors)

  4. Optimizing in vitro large scale production of giant reed (Arundo donax L.) by liquid medium culture

    International Nuclear Information System (INIS)

    Cavallaro, Valeria; Patanè, Cristina; Cosentino, Salvatore L.; Di Silvestro, Isabella; Copani, Venera

    2014-01-01

    Tissue culture methods offer the potential for large-scale propagation of giant reed (Arundo donax L.), a promising crop for energy biomass. In previous trials, giant reed resulted particularly suitable to in vitro culture. In this paper, with the final goal of enhancing the efficiency of in vitro production process and reducing costs, the influence of four different culture media (agar or gellan-gum solidified medium, liquid medium into a temporary immersion system-RITA ® or in a stationary state) on in vitro shoot proliferation of giant reed was evaluated. Giant reed exhibited a particular sensitivity to gelling agents during the phase of secondary shoot formation. Gellan gum, as compared to agar, improved the efficiency of in vitro culture giving more shoots with higher mean fresh and dry weight. Moreover, the cultivation of this species into a liquid medium under temporary immersion conditions or in a stationary state, was comparatively as effective as and cheaper than that into a gellan gum medium. Increasing 6-benzylaminopurine (BA) up to 4 mg l −1 also resulted in a further enhancement of secondary shoot proliferation. The good adaptability of this species to liquid medium and the high multiplication rates observed indicate the possibility to obtain from a single node at least 1200 plantlets every six multiplication cycles (about 6 months), a number 100 fold higher than that obtained yearly per plant by the conventional methods of vegetative multiplication. In open field, micropropagated plantlets guaranteed a higher number of survived plants, secondary stems and above ground biomass as compared to rhizome ones. - Highlights: • In vitro propagation offers the potential for large-scale propagation of giant reed. • The success of an in vitro protocol depends on the rate and mode of shoot proliferation. • Substituting liquid media to solid ones may decrease propagation costs in Arundo donax. • Giant reed showed good proliferation rates in

  5. Hatchling sex ratio and female mating status in the great reed warbler, Acrocephalus arundinaceus (Aves, Passeriformes): further evidence for offspring sex ratio manipulation

    Czech Academy of Sciences Publication Activity Database

    Trnka, A.; Prokop, P.; Kašová, M.; Sobeková, Karolina; Kocian, Ľ.

    2012-01-01

    Roč. 79, č. 2 (2012), s. 212-217 ISSN 1125-0003 Institutional support: RVO:68081766 Keywords : Great reed warbler * sex ratio * social polygyny Subject RIV: EG - Zoology Impact factor: 0.890, year: 2012

  6. Business Case Analysis of the Walter Reed Army Medical Center Medical/Surgical Prime Vendor Generation III Service Level Electron Program

    National Research Council Canada - National Science Library

    Markot, Peter B

    2007-01-01

    ...) staffing and medical/surgical services offered under the Prime Vendor (PV) Generation III contract would provide the best supply chain management solution for Walter Reed Army Medical Center (WRAMC...

  7. Measurement of the bed material of gravel-bed rivers

    Science.gov (United States)

    Milhous, R.T.; ,

    2002-01-01

    The measurement of the physical properties of a gravel-bed river is important in the calculation of sediment transport and physical habitat values for aquatic animals. These properties are not always easy to measure. One recent report on flushing of fines from the Klamath River did not contain information on one location because the grain size distribution of the armour could not be measured on a dry river bar. The grain size distribution could have been measured using a barrel sampler and converting the measurements to the same as would have been measured if a dry bar existed at the site. In another recent paper the porosity was calculated from an average value relation from the literature. The results of that paper may be sensitive to the actual value of porosity. Using the bulk density sampling technique based on a water displacement process presented in this paper the porosity could have been calculated from the measured bulk density. The principle topics of this paper are the measurement of the size distribution of the armour, and measurement of the porosity of the substrate. The 'standard' method of sampling of the armour is to do a Wolman-type count of the armour on a dry section of the river bed. When a dry bar does not exist the armour in an area of the wet streambed is to sample and the measurements transformed analytically to the same type of results that would have been obtained from the standard Wolman procedure. A comparison of the results for the San Miguel River in Colorado shows significant differences in the median size of the armour. The method use to determine the porosity is not 'high-tech' and there is a need improve knowledge of the porosity because of the importance of porosity in the aquatic ecosystem. The technique is to measure the in-situ volume of a substrate sample by measuring the volume of a frame over the substrate and then repeated the volume measurement after the sample is obtained from within the frame. The difference in the

  8. Effectiveness of Bed Bug Pesticides

    Science.gov (United States)

    Before EPA allows a bed bug claim on a label, the product must be supported by data showing it will kill bed bugs when applied according to the label. Also consider factors such as extent of infestation, site preparation, and insect life stages.

  9. Performance Evaluation of the ISS Water Processor Multifiltration Beds

    Science.gov (United States)

    Bowman, Elizabeth M.; Carter, Layne; Wilson, Mark; Cole, Harold; Orozco, Nicole; Snowdon, Doug

    2012-01-01

    The ISS Water Processor Assembly (WPA) produces potable water from a waste stream containing humidity condensate and urine distillate. The primary treatment process is achieved in the Multifiltration Bed, which includes adsorbent media and ion exchange resin for the removal of dissolved organic and inorganic contaminants. The first Multifiltration Bed was replaced on ISS in July 2010 after initial indication of inorganic breakthrough. This bed was returned to ground in July 2011 for an engineering investigation. The water resident in the bed was analyzed for various parameters to evaluate adsorbent loading, performance of the ion exchange resin, microbial activity, and generation of leachates from the ion exchange resin. Portions of the adsorbent media and ion exchange resin were sampled and subsequently desorbed to identify the primary contaminants removed at various points in the bed. In addition, an unused Multifiltration Bed was evaluated after two years in storage to assess the generation of leachates during storage. This assessment was performed to evaluate the possibility that these leachates are impacting performance of the Catalytic Reactor located downstream of the Multifiltration Bed. The results of these investigations and implications to the operation of the WPA on ISS are documented in this paper.

  10. Effect of particle stratification on debris-bed dryout

    International Nuclear Information System (INIS)

    Gabor, J.D.; Cassulo, J.C.; Pederson, D.R.

    1982-01-01

    Significant work has been performed on debris-bed dryout on beds of either uniformly sized particles or particles of a wide size range which are well mixed. This work has provided an understanding of the mechanisms of dryout and an empirical basis for containment analysis. However, the debris bed resulting from a HCDA would not consist of uniformly sized particles and for certain scenarios the bed could be stratified rather than well mixed. Tests have been conducted on the effect of particle size distribution on dryout and concluded that not only is the mean particle size an important parameter but also the standard deviation of the distribution and change in porosity. The D6 in-pile test at Sandia with a 114-mm deep stratified bed resulted in a reduced dryout heat flux compared to a uniformly mixed bed. Because of the many questions concerning the dryout behavior of stratified beds of wide size distribution out-of-pile experiments in which metal particles in water pools are inductively heated were initiated at Argonne

  11. Technical development to increase the use of reed canary grass - Full scale demonstration; Teknikutveckling foer oekad etablering och nyttjande av roerflen - Demonstrationsfoersoek i fullskala

    Energy Technology Data Exchange (ETDEWEB)

    Oerberg, Haakan; Skoglund, Nils; Grimm, Alejandro; Bostroem, Dan; Oehman, Marcus

    2010-06-15

    Introducing fuels from agricultural crops into the heat and power sector in Sweden is a desired and needed development, thus it is connected to some obstacles. For the crop producers it is important to use the most efficient handling for harvest, collection, loading and transport technology in order to reach low production costs. For the fuel consumers it is of high importance that these fuels work together with other utilized fuels in mixtures without complications. This includes fuel mixing, fuel feeding, combustion behavior and ash transformation mechanisms. Specifically for the combustion process, gaseous and particle emissions, ash behavior and deposit formation on cooled surfaces should not be negatively effected by mixing in agricultural crops. In this study these aspects of the energy crop reed canary grass (RCG) have been examined. The recommended harvest period for harvesting RCG in Sweden is during springtime when the crop from the year before is collected, called delayed harvest. During this period the grass is very dry and has been harvested in this project with an average water content of 11,3 %. Two major different harvest systems have been tested. One where the energy grass is chopped directly in the field by a chopper connected to a wagon. The other system was based on baling the crop with round balers or big square balers. The chopped or baled material is transported 6 km to a farm center or terminal for unloading. Further transport to CHP (Combined Heat and Power) plant, 12 km, was done with road truck (135 m3). In the case of field chopped RCG the mixing of the other fuels has been easily done since the material was well chopped (40-50 mm). The RCG was mixed into a mixture of peat and wood to a share of 10-12% of the total energy content of the mixture. Also the baled material was transported to a farm centre or terminal for unloading the farm wagon and loading on a road truck (135 m3). In this case an additional procedure is needed for chopping

  12. Carbon Bed Mercury Emissions Control For Mixed Waste Treatment

    International Nuclear Information System (INIS)

    Soelberg, Nick; Enneking, Joe

    2010-01-01

    Mercury has had various uses in nuclear fuel reprocessing and other nuclear processes, and so is often present in radioactive and mixed (both radioactive and hazardous according to the Resource Conservation and Recovery Act) wastes. Depending on regulatory requirements, the mercury in the off-gas must be controlled with sometimes very high efficiencies. Compliance to the Hazardous Waste Combustor (HWC) Maximum Achievable Control Technology (MACT) standards can require off-gas mercury removal efficiencies up to 99.999% for thermally treating some mixed waste streams. Several test programs have demonstrated this level of off-gas mercury control using fixed beds of granular sulfur-impregnated activated carbon. Other results of these tests include: (a) The depth of the mercury control mass transfer zone was less than 15-30 cm for the operating conditions of these tests, (b) MERSORB(reg s ign) carbon can sorb Hg up to 19 wt% of the carbon mass, and (c) the spent carbon retained almost all (98-99.99%) of the Hg; but when even a small fraction of the total Hg dissolves, the spent carbon can fail the TCLP test when the spent carbon contains high Hg concentrations. Localized areas in a carbon bed that become heated through heat of adsorption, to temperatures where oxidation occurs, are referred to as 'bed hot spots.' Carbon bed hot spots must be avoided in processes that treat radioactive and mixed waste. Key to carbon bed hot spot mitigation are (a) designing for sufficient gas velocity, for avoiding gas flow maldistribution, and for sufficient but not excessive bed depth, (b) monitoring and control of inlet gas flowrate, temperature, and composition, (c) monitoring and control of in-bed and bed outlet gas temperatures, and (d) most important, monitoring of bed outlet CO concentrations. An increase of CO levels in the off-gas downstream of the carbon bed to levels about 50-100 ppm higher than the inlet CO concentration indicate CO formation in the bed, caused by carbon bed

  13. Method for maintenance of ice beds of ice condenser containment

    International Nuclear Information System (INIS)

    Scrabis, C.M.; Hardin, R.T. Jr.

    1987-01-01

    This patent describes a method of maintaining ice baskets associated with a nuclear reactor system and disposed in an array of plural such ice baskets, supported in generally vertically oriented and parallel relationship by a lattice support structure which extends between the individual ice baskets and includes lateral supports adjacent the tops of the comprising: selecting an ice basket of the array requiring replenishment of the ice therewithin due to sublimation voids within the ice charges in the basket; isolating the selected ice basket; drilling a hole downwardly through the ice charges in the ice basket in general parallel axial relationship with respect to the cylindrical sidewall of the ice basket, utilizing a rotary drill bit connected through an auger to a rotary drive means; maintaining the rotary drive means in a fixed axial position and reversing the direction of rotation thereof for driving the auger in reverse rotation; and supplying ice in particulate form to the vicinity of the auger and conveying the particulate ice through the drilled hole by continued, reverse rotation of the auger so as to fill the sublimated voids in communication with the drilled hole, from the lowest and through successively higher such voids in the ice charges within the ice basket, and withdrawing the auger from the drilled hole as the voids are filled

  14. Contribution to harmonic balance calculations of self-sustained periodic oscillations with focus on single-reed instruments.

    Science.gov (United States)

    Farner, Snorre; Vergez, Christophe; Kergomard, Jean; Lizée, Aude

    2006-03-01

    The harmonic balance method (HBM) was originally developed for finding periodic solutions of electronical and mechanical systems under a periodic force, but has been adapted to self-sustained musical instruments. Unlike time-domain methods, this frequency-domain method does not capture transients and so is not adapted for sound synthesis. However, its independence of time makes it very useful for studying any periodic solution, whether stable or unstable, without care of particular initial conditions in time. A computer program for solving general problems involving nonlinearly coupled exciter and resonator, HARMBAL, has been developed based on the HBM. The method as well as convergence improvements and continuation facilities are thoroughly presented and discussed in the present paper. Applications of the method are demonstrated, especially on problems with severe difficulties of convergence: the Helmholtz motion (square signals) of single-reed instruments when no losses are taken into account, the reed being modeled as a simple spring.

  15. Evaluating the Value of High Spatial Resolution in National Capacity Expansion Models using ReEDS: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Krishnan, Venkat; Cole, Wesley

    2016-07-01

    Power sector capacity expansion models (CEMs) have a broad range of spatial resolutions. This paper uses the Regional Energy Deployment System (ReEDS) model, a long-term national scale electric sector CEM, to evaluate the value of high spatial resolution for CEMs. ReEDS models the United States with 134 load balancing areas (BAs) and captures the variability in existing generation parameters, future technology costs, performance, and resource availability using very high spatial resolution data, especially for wind and solar modeled at 356 resource regions. In this paper we perform planning studies at three different spatial resolutions--native resolution (134 BAs), state-level, and NERC region level--and evaluate how results change under different levels of spatial aggregation in terms of renewable capacity deployment and location, associated transmission builds, and system costs. The results are used to ascertain the value of high geographically resolved models in terms of their impact on relative competitiveness among renewable energy resources.

  16. Long-term ionizing radiation impact on seed progeny of common reed in water bodies of the Chernobyl exclusive zone

    International Nuclear Information System (INIS)

    Shevtsova, N.L.; Yavnyuk, A.A.; Gudkov, D.Yi.

    2012-01-01

    Results of the investigation of common reed's (Phragmites australis (Trin) Ex. Steud.) biological characteristics under conditions of long-term ionizing radiation impact are represented. Indices of seeds' vitality and disorders are analyzed. Low vitality indices, significant ontogenesis disorders, and high percent of abnormalities of germs are determined in water bodies, where littoral plants receive the absorbed dose in a low-dose range of 1-12 cGy year -1 .

  17. Protecting Your Home from Bed Bugs

    Science.gov (United States)

    ... your home: Inspect the luggage rack in your hotel room for bed bugs. Check secondhand furniture, beds, ... with Bed Bug Problems Discover. Accessibility EPA Administrator Budget & Performance Contracting Grants January 19, 2017 Web Snapshot ...

  18. Intercropping of reed canary grass, phalaris arundinacea l., with legumes can cut costs for n-fertilization

    Energy Technology Data Exchange (ETDEWEB)

    Palmborg, Cecilia; Lindvall, Eva (Swedish Univ. of Agricultural Sciences, Dept. of Agricultural Research for Northern Sweden, Umeaa (Sweden)), e-mail: eva.lindvall@njv.slu.se

    2010-07-15

    In a field experiment close to Oestersund in mid Sweden reed canary grass was intercropped with barley, Alsike clover, Trifolium hybridum L., red clover, T. pratense L., goats rue, Galega orientalis L. or a combination of red clover and goats rue. There were also three fertilization treatments: A: Recommended amounts of N, P and K. B: Recommended amounts of P and K and half amount of N. C: Sewage sludge application before sowing (establishment year) and recommended amounts of P and K and half amount of N. The biomass was lower where reed canary grass had been undersown in barley, and higher with full N-fertilization than with half N-fertilization. However there were no significant differences between legume intercrops with half N-fertilization and pure reed canary grass with full Nfertilization. Alsike clover was the most productive legume, followed by red clover. The amount of nitrogen fixed by the legumes was less with full N-fertilization (29 kg/ha as a mean) than with half N-fertilization (38 kg/ha). Intercropping with legumes could substitute half of the N in fertilization but similar experiments in other parts of Sweden has shown that there is a higher risk of weed problems

  19. Gas fluidized bed reactor

    International Nuclear Information System (INIS)

    Bernardelli, H. da C.

    1976-03-01

    The equations of motion for both gas and particles in a gas fluidised system are stablished through general assumptions which are generally accepted on physical grounds. The resulting model is used to study the velocity fields of each phase in the case of an isolated bubble rising close to the flat distributor plate. A well posed problem results for the solution of Laplace's equation of the potential flow of the particles when consideration is given to the presence of the distributor as a boundary condition. The corresponding stream functions are also obtained which enable the drawing of the motion patterns using numerical techniques. The following two dimensional cases are analysed: S/b=1; S/b=1,5; S/b=2,5; S/b=5 and the limiting case S/b→αinfinite. The results for the interphase exchange between bubbles and particulate phases are applied to a gas fluidised bed reactor and its effect on the chemical conversion is studied for the simplest cases of piston flow and perfect mixing in the particulate phase [pt

  20. High-Speed Soft-Decision Decoding of Two Reed-Muller Codes

    Science.gov (United States)

    Lin, Shu; Uehara, Gregory T.

    1996-01-01

    In his research, we have proposed the (64, 40, 8) subcode of the third-order Reed-Muller (RM) code to NASA for high-speed satellite communications. This RM subcode can be used either alone or as an inner code of a concatenated coding system with the NASA standard (255, 233, 33) Reed-Solomon (RS) code as the outer code to achieve high performance (or low bit-error rate) with reduced decoding complexity. It can also be used as a component code in a multilevel bandwidth efficient coded modulation system to achieve reliable bandwidth efficient data transmission. This report will summarize the key progress we have made toward achieving our eventual goal of implementing a decoder system based upon this code. In the first phase of study, we investigated the complexities of various sectionalized trellis diagrams for the proposed (64, 40, 8) RNI subcode. We found a specific 8-trellis diagram for this code which requires the least decoding complexity with a high possibility of achieving a decoding speed of 600 M bits per second (Mbps). The combination of a large number of states and a hi ch data rate will be made possible due to the utilization of a high degree of parallelism throughout the architecture. This trellis diagram will be presented and briefly described. In the second phase of study which was carried out through the past year, we investigated circuit architectures to determine the feasibility of VLSI implementation of a high-speed Viterbi decoder based on this 8-section trellis diagram. We began to examine specific design and implementation approaches to implement a fully custom integrated circuit (IC) which will be a key building block for a decoder system implementation. The key results will be presented in this report. This report will be divided into three primary sections. First, we will briefly describe the system block diagram in which the proposed decoder is assumed to be operating and present some of the key architectural approaches being used to

  1. Chaotic hydrodynamics of fluidized beds

    Energy Technology Data Exchange (ETDEWEB)

    Van der Stappen, M.L.M. [Unit Process and Systems Engineering, Advanced Manufacturing Technology Group, Unilever Research Laboratorium, Vlaardingen (Netherlands)

    1996-12-31

    The major goals of this thesis are: (1) to develop and evaluate an analysis method based on techniques from non-linear chaos theory to characterize the nonlinear hydrodynamics of gas-solids fluidized beds quantitatively; and (2) to determine the dependence of the chaotic invariants on the operating conditions and investigate how the chaos analysis method can be profitably applied to improve scale-up and design of gas-solids fluidized bed reactors. Chaos theory is introduced in chapter 2 with emphasis on analysis techniques for (experimental) time series, known from literature at the start of this work (1990-1991). In chapter 3, the testing of existing and newly developed techniques on both model and fluidized bed data is described. This leads to the development of the chaos analysis method to analyze measured pressure fluctuations time series of a fluidized bed. Following, in chapter 4, this method is tested and all choices for the parameters are evaluated. The influence of the experimental parameters and external disturbances on the measurements and analysis results is discussed and quantified. The result is a chaos measurement and analysis protocol, which is further used in this work. In chapter 5, the applications to fluidized beds are discussed. It is shown that the entropy is a good measure for the characterization of the dynamical behavior of gas-solids bubbling/slugging fluidized beds. Entropy is applied to characterize the influence of the operating conditions, to assess regime transitions and to analyze dimensionless similar beds of different scale. Quantitative design correlations that relate entropy to the operating parameters (including the bed diameter) are described. Finally, it is discussed how the results of this work might be used in scaling up the chaotic dynamics of fluidized beds. The overall conclusions and outlook from this work are presented in chapter 6. 182 refs.

  2. Bed retained products in swept fixed bed (SFB) coal hydropyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Mastral, A.M.; Perez-Surio, M.J. [CSIC, Zaragosa (Spain). Inst. de Carboquimica

    1997-12-31

    The hydropyrolysis of a low rank coal in a swept fixed bed (SFB) reactor is carried out by fixing the hydrogen pressure (40 kg/cm{sup 2}), the hydrogen flow (2 l/min) and the residence time (10 min) at increasing temperatures (400 C, 500 C and 600 C) and coal bed heights (h, 1.5h, 2h, 2.5h and 3h). It is shown that the percentages of tars and char directly depend on the coal bed height and that there is not only a quantitative dependence, but also the height of the coal bed is very important and plays a relevant role on the nature of the conversion products. (orig.)

  3. Bed diameter effects and incipient slugging in gas fluidized beds

    International Nuclear Information System (INIS)

    Agarwal, P.K.

    1986-01-01

    The coalescence and growth of bubble swarms formed at the distributor of a fluidized bed gives rise to lateral as well as vertical distributions of bubble properties. However, existing models employ average bubble properties obtained largely from semi-empirical considerations. In a recent Paper, the author developed a bubble growth model based on a population balance approach. Analytical expressions were derived for the bubble characteristic distributions and averages. However, the model, developed for unconstrained growth, did not take into account the effect of the bed diameter and the possibility of slugging. In this Paper, the model is extended to take these aspects into account. A slugging criterion is also developed which is expected to be valid for the regime where incipient slugging depends on the bed height as well as the region where bed height does not significantly affect minimum slugging conditions

  4. Endotoxin, Coliform, and Dust Levels in Various Types of Rodent Bedding

    OpenAIRE

    Whiteside, Tanya E; Thigpen, Julius E; Kissling, Grace E; Grant, Mary G; Forsythe, Diane B

    2010-01-01

    Endotoxins in grain dust, household dust, and animal bedding may induce respiratory symptoms in rodents and humans. We assayed the endotoxin, coliform, and dust levels in 20 types of rodent bedding. Endotoxin concentrations were measured by using a commercial test kit, coliform counts were determined by using conventional microbiologic procedures, and dust content was evaluated by using a rotating–tapping shaker. Paper bedding types contained significantly less endotoxin than did other beddin...

  5. Use of soft hydrothermal processing to improve and recycle bedding for laboratory animals.

    Science.gov (United States)

    Miyamoto, T; Li, Z; Kibushi, T; Yamasaki, N; Kasai, N

    2008-10-01

    Cage bedding for laboratory rodents can influence animal wellbeing and thus the experimental data. In addition, a large amount of used bedding containing excrement is discharged as medical waste from life science institutes and breeding companies. We developed a ground-breaking system to improve fresh bedding and recycle used bedding by applying a soft hydrothermal process with high-temperature and high-pressure dry steam. The system removes both harmful organic components and aromatic hydrocarbons that can affect animals' metabolism. The purpose of the present study was to evaluate the chemical and physical properties of the improved fresh bedding and the recycled used bedding treated by the system. The results showed that 68-99% of the predominant aromatic hydrocarbons were removed from fresh bedding treated at 0.35 MPa and 140 degrees C for 120 min ('improved bedding'). In addition, 59.4-99.0% of predominant harmful organic compounds derived from excrement were removed from used bedding treated at 0.45 MPa and 150 degrees C for 60 min ('recycled bedding'). The soft hydrothermal treatment increased the number of acidic functional groups on the bedding surface and gave it the high adsorptive efficiency of ammonia gas. Harmful substances such as microorganisms, heavy metals and pesticides decreased below the detection limit. The results clearly showed that the improved and recycled bedding is safer for laboratory rodents and has the potential to ameliorate conditions in primary and secondary enclosures (e.g. cages and animal rooms) used for maintaining laboratory animals. This process may be one of the most advanced techniques in providing an alternative to softwood and other bedding, economizing through the recycling of used bedding and reducing bedding waste from animal facilities.

  6. Using multiple bed load measurements: Toward the identification of bed dilation and contraction in gravel-bed rivers

    Science.gov (United States)

    Marquis, G. A.; Roy, A. G.

    2012-02-01

    This study examines bed load transport processes in a small gravel-bed river (Béard Creek, Québec) using three complementary methods: bed elevation changes between successive floods, bed activity surveys using tags inserted into the bed, and bed load transport rates from bed load traps. The analysis of 20 flood events capable of mobilizing bed material led to the identification of divergent results among the methods. In particular, bed elevation changes were not consistent with the bed activity surveys. In many cases, bed elevation changes were significant (1 to 2 times the D50) even if the bed surface had not been activated during the flood, leading to the identification of processes of bed dilation and contraction that occurred over 10% to 40% of the bed surface. These dynamics of the river bed prevent accurate derivation of bed load transport rates from topographic changes, especially for low magnitude floods. This paper discusses the mechanisms that could explain the dilation and contraction of particles within the bed and their implications in fluvial dynamics. Bed contraction seems to be the result of the winnowing of the fine sediments under very low gravel transport. Bed dilation seems to occur on patches of the bed at the threshold of motion where various processes such as fine sediment infiltration lead to the maintenance of a larger sediment framework volume. Both processes are also influenced by flood history and the initial local bed state and in turn may have a significant impact on sediment transport and morphological changes in gravel-bed rivers.

  7. Study on effective particle diameters and coolability of particulate beds packed with irregular multi-size particles

    Energy Technology Data Exchange (ETDEWEB)

    Thakre, S.; Ma, W.; Kudinov, P.; Bechta, S. [Royal Institute of Technology, KTH. Div. of Nuclear Power Safety, Stockholm (Sweden)

    2013-08-15

    the POMECO-HT facility using particulate beds packed with the same particles as in POMECO-FL. The dryout heat flux of the bed with aluminum oxide gravels under top flooding is found to be close to the prediction of the Lipinski model. The dryout heat flux increases by 51% when applying a 12-mm size downcomer. The dryout heat flux of the bed with zirconium particles test lies between the values predicted by the Reed model and Lipinski model. The use of the 12-mm size downcomer increases dryout heat flux by 16%. (Author)

  8. Study on effective particle diameters and coolability of particulate beds packed with irregular multi-size particles

    International Nuclear Information System (INIS)

    Thakre, S.; Ma, W.; Kudinov, P.; Bechta, S.

    2013-08-01

    the POMECO-HT facility using particulate beds packed with the same particles as in POMECO-FL. The dryout heat flux of the bed with aluminum oxide gravels under top flooding is found to be close to the prediction of the Lipinski model. The dryout heat flux increases by 51% when applying a 12-mm size downcomer. The dryout heat flux of the bed with zirconium particles test lies between the values predicted by the Reed model and Lipinski model. The use of the 12-mm size downcomer increases dryout heat flux by 16%. (Author)

  9. Effects of bedding quality on lying behavior of dairy cows.

    Science.gov (United States)

    Fregonesi, J A; Veira, D M; von Keyserlingk, M A G; Weary, D M

    2007-12-01

    Cows prefer to spend more time lying down in free stalls with more bedding, but no research to date has addressed the effects of bedding quality. Bedding in stalls often becomes wet either from exposure to the elements or from feces and urine. The aim of this study was to test the effect of wet bedding on stall preference and use. Four groups of 6 nonlactating Holstein cows were housed in free stalls bedded daily with approximately 0.1 m of fresh sawdust. Following a 5-d adaptation period, each group of cows was tested sequentially with access to stalls with either dry or wet sawdust bedding (86.4 +/- 2.1 vs. 26.5 +/- 2.1% dry matter), each for 2 d. These no-choice phases were followed by a 2-d free-choice phase during which cows had simultaneous access to stalls containing either wet or dry bedding. Stall usage was assessed by using 24-h video recordings scanned at 10-min intervals, and responses were analyzed by using a mixed model, with group (n = 4) as the observational unit. The minimum and maximum environmental temperatures during the experiment were 3.4 +/- 2.2 and 6.8 +/- 2.5 degrees C, respectively. When cows had access only to stalls with wet bedding, they spent 8.8 +/- 0.8 h/d lying down, which increased to 13.8 +/- 0.8 h/d when stalls with dry bedding were provided. Cows spent more time standing with their front 2 hooves in the stall when provided with wet vs. dry bedding (92 +/- 10 vs. 32 +/- 10 min/d). During the free-choice phase, all cows spent more time lying down in the dry stalls, spending 12.5 +/- 0.3 h/d in the dry stalls vs. 0.9 +/- 0.3 h/ d in stalls with wet bedding. In conclusion, dairy cows show a clear preference for a dry lying surface, and they spend much more time standing outside the stall when only wet bedding is available.

  10. Primary peak and chronic malaria infection levels are correlated in experimentally infected great reed warblers.

    Science.gov (United States)

    Asghar, Muhammad; Westerdahl, Helena; Zehtindjiev, Pavel; Ilieva, Mihaela; Hasselquist, Dennis; Bensch, Staffan

    2012-09-01

    Malaria parasites often manage to maintain an infection for several months or years in their vertebrate hosts. In humans, rodents and birds, most of the fitness costs associated with malaria infections are in the short initial primary (high parasitaemia) phase of the infection, whereas the chronic phase (low parasitaemia) is more benign to the host. In wild birds, malaria parasites have mainly been studied during the chronic phase of the infection. This is because the initial primary phase of infection is short in duration and infected birds with severe disease symptoms tend to hide in sheltered places and are thus rarely caught and sampled. We therefore wanted to investigate the relationship between the parasitaemia during the primary and chronic phases of the infection using an experimental infection approach. We found a significant positive correlation between parasitaemia in the primary peak and the subsequent chronic phase of infection when we experimentally infected great reed warblers (Acrocephalus arundinaceus) with Plasmodium ashfordi. The reason for this association remains to be understood, but might arise from individual variation in exoerythrocytic parasite reservoirs in hosts, parasite antigenic diversity and/or host genetics. Our results suggest that the chronic phase parasitaemia can be used to qualitatively infer the parasitaemia of the preceding and more severe primary phase, which is a very important finding for studies of avian malaria in wild populations.

  11. Complexity Analysis of Reed-Solomon Decoding over GF(2m without Using Syndromes

    Directory of Open Access Journals (Sweden)

    Zhiyuan Yan

    2008-06-01

    Full Text Available There has been renewed interest in decoding Reed-Solomon (RS codes without using syndromes recently. In this paper, we investigate the complexity of syndromeless decoding, and compare it to that of syndrome-based decoding. Aiming to provide guidelines to practical applications, our complexity analysis focuses on RS codes over characteristic-2 fields, for which some multiplicative FFT techniques are not applicable. Due to moderate block lengths of RS codes in practice, our analysis is complete, without big O notation. In addition to fast implementation using additive FFT techniques, we also consider direct implementation, which is still relevant for RS codes with moderate lengths. For high-rate RS codes, when compared to syndrome-based decoding algorithms, not only syndromeless decoding algorithms require more field operations regardless of implementation, but also decoder architectures based on their direct implementations have higher hardware costs and lower throughput. We also derive tighter bounds on the complexities of fast polynomial multiplications based on Cantor's approach and the fast extended Euclidean algorithm.

  12. Complexity Analysis of Reed-Solomon Decoding over GF without Using Syndromes

    Directory of Open Access Journals (Sweden)

    Chen Ning

    2008-01-01

    Full Text Available Abstract There has been renewed interest in decoding Reed-Solomon (RS codes without using syndromes recently. In this paper, we investigate the complexity of syndromeless decoding, and compare it to that of syndrome-based decoding. Aiming to provide guidelines to practical applications, our complexity analysis focuses on RS codes over characteristic-2 fields, for which some multiplicative FFT techniques are not applicable. Due to moderate block lengths of RS codes in practice, our analysis is complete, without big notation. In addition to fast implementation using additive FFT techniques, we also consider direct implementation, which is still relevant for RS codes with moderate lengths. For high-rate RS codes, when compared to syndrome-based decoding algorithms, not only syndromeless decoding algorithms require more field operations regardless of implementation, but also decoder architectures based on their direct implementations have higher hardware costs and lower throughput. We also derive tighter bounds on the complexities of fast polynomial multiplications based on Cantor's approach and the fast extended Euclidean algorithm.

  13. Structural and mechanical design of tissue interfaces in the giant reed Arundo donax.

    Science.gov (United States)

    Rüggeberg, Markus; Burgert, Ingo; Speck, Thomas

    2010-03-06

    The culms of the giant reed Arundo donax represent slender tube-like structures. Several nodes along the culm, a ring of sclerenchymatous fibres in the periphery of the culm wall and numerous isolated vascular bundles enclosed by fibre rings in the culm wall function as stiffening elements. The bundles are embedded in lignified parenchyma. Micromechanical analysis indicated differences in stiffness between the individual tissues of more than one order of magnitude. In case of abrupt transitions in stiffness at the interfaces, stress discontinuities arise under dynamic loads. This eventually leads to critical shear stresses at cell ends, and culm failure may be initiated at these points. Pronounced mechanical differences between individual tissues can be compromised by gradual transitions at their interfaces. Ultrastructural and spectroscopic investigations with high spatial resolution revealed a gradual transition of cell parameters (cell wall area fraction and cell length). However, cell wall parameters (cellulose microfibril angle and lignin content) showed abrupt transitions or remained almost constant across the interfaces between various tissues. The design principles found at the interfaces between tissues in the culm walls of A. donax are discussed as an adaptation strategy to mechanical loads at different levels of hierarchy.

  14. Columbia Estuary Ecosystem Restoration Program: Restoration Design Challenges for Topographic Mounds, Channel Outlets, and Reed Canarygrass

    Energy Technology Data Exchange (ETDEWEB)

    Diefenderfer, Heida L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Borde, Amy B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Sinks, Ian A. [Columbia Land Trust, Vancouver, WA (United States); Cullinan, Valerie I. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Zimmerman, Shon A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-08-31

    The purpose of this study was to provide science-based information to practitioners and managers of restoration projects in the Columbia Estuary Ecosystem Restoration Program (CEERP) regarding aspects of restoration techniques that currently pose known challenges and uncertainties. The CEERP is a program of the Bonneville Power Administration (BPA) and the U.S. Army Corps of Engineers (Corps), Portland District, in collaboration with the National Marine Fisheries Service and five estuary sponsors implementing restoration. The estuary sponsors are Columbia Land Trust, Columbia River Estuary Study Taskforce, Cowlitz Tribe, Lower Columbia Estuary Partnership, and Washington Department of Fish and Wildlife. The scope of the research conducted during federal fiscal year 2015 included three aspects of hydrologic reconnection that were selected based on available scientific information and feedback from restoration practitioners during project reviews: the design of mounds (also called hummocks, peninsulas, or berms); the control of reed canarygrass (Phalaris arundinaceae); and aspects of channel network design related to habitat connectivity for juvenile salmonids.

  15. Reed canary grass on marginal land. Industrial applications, economics and environmental impacts

    International Nuclear Information System (INIS)

    Pedersen, S.M.

    1997-01-01

    The objective of this study concerns the industrial applications and economic viability of using RCG (Reed Canary Grass). The study is based on a systems and costs analysis where the cost structure in the whole production chain is assessed. This includes cultivation, harvest, transportation, fractionation, pelletizing, combustion and pump production. Moreover the study assess the environmental impact by comparing the use of pesticides and fertilizers with conventional crops. A few scenarios are selected in order to conduct further sensitivity analysis regarding price fluctuations, set aside premiums, energy taxation and variation in cost of land. In addition, the study describes the market possibilities for RCG end products in Europe. The market for short fibre pump is stable in Finland and Sweden and calculations indicate potential possibilities of using upgraded RCG on existing sulphate pulp and paper mills. The upgraded leave fraction should be used for either district heating, small scale heating or process energy at the pump mill. Furthermore, the calculations show that it is economic viable to grow RCG on marginal land with a minimum environmental impact compared with conventional crops. (au) 18 refs

  16. Leaf Composition of American Bur-Reed (Sparganium americanum Nutt.) to Determine Pesticide Mitigation Capability.

    Science.gov (United States)

    Alsharekh, Anfal; Swatzell, Lucinda J; Moore, Matthew T

    2018-04-01

    American bur-reed (Sparganium americanum Nutt.), a common aquatic plant in the middle and eastern United States and Canada, is often located in water-retaining drainage areas. The purpose of this study was to determine the leaf composition of S. americanum, paying attention to the cuticular waxes and the epidermis, and its ability to sorb pesticides. S. americanum leaves (n = 100) were collected in both early (June) and late (August) summer. Transverse sections of S. americanum were stained and studied with brightfield and fluorescence microscopy to estimate the structural and chemical nature of the leaf tissues cross sections. Mean total lipid content in early summer leaf samples (1.47 ± 0.83 mg mL -1 ) was significantly greater (alpha 0.05) than late summer leaves (0.15 ± 0.36 mg mL -1 ). In vitro analysis of epidermal peel permeability exposed to atrazine and malathion determined little to no sorption by the plant. Therefore, the structure of S. americanum leaves suggest this species does not have the capacity of sorbing these pesticides from runoff water.

  17. Better backs by better beds?

    DEFF Research Database (Denmark)

    Bergholdt, Kim; Fabricius, Rasmus N; Bendix, Tom

    2008-01-01

    mattresses have a positive effect on LBP, and especially a hard mattress is commonly believed to have a positive effect. METHODS: One hundred sixty CLBP patients were randomized to 1 of 3 groups, having a mattress/bed mounted in their sleeping room for 1 month. The beds were: (1) waterbed (Akva), (2) body......-conforming foam mattress (Tempur), and (3) a hard mattress (Innovation Futon). At baseline and after 4 weeks, a blinded observer interviewed the patients on LBP levels (0-10), daily function (activities of daily living, 0-30), and on the amount of sleeping hours/night. RESULTS: Because of dropout of 19 patients...... using the probably most relevant "worst case" data. There were no relevant difference between the effects of the water bed and the foam bed. CONCLUSION: The Waterbed and foam mattress' did influence back symptoms, function and sleep more positively as apposed to the hard mattress, but the differences...

  18. Top Ten Bed Bug Tips

    Science.gov (United States)

    ... Directory Planning, Budget and Results Jobs and Internships Headquarters Offices Regional Offices Labs and Research Centers Bed ... you hire an expert, be sure it’s a company with a good reputation and request that it ...

  19. Sea bed mapping and inspection

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    The conference has 24 presentations on the topics: Sea bed mapping, inspection, positioning, hydrography, marine archaeology, remote operation vehicles and computerized simulation technologies, oil field activities and plans, technological experiences and problems. (tk)

  20. Measurement of thermal expansion for a Li2TiO3 pebble bed

    International Nuclear Information System (INIS)

    Hisashi Tanigawa; Mikio Enoeda; Masato Akiba

    2006-01-01

    In the current design of the blanket with ceramic breeders, pebbles of breeding materials are packed into a container and used as a pebble bed. Thermal and mechanical conditions externally loaded on the bed affect thermal and mechanical properties of the bed. It is necessary to analyze thermo-mechanical properties of the bed under controlled thermal and mechanical conditions. In the present paper, thermal expansion of a Li 2 TiO 3 pebble bed was investigated. Our apparatus consists of a tensile test-apparatus and a measurement chamber. Pebbles of Li 2 TiO 3 with 2 mm diameter were used. They were packed into a container made of alumina. At first, thermal expansion of the apparatus was calibrated because the measured deformation included thermal expansions of the load rods and the container. Instead of the pebble bed, a column made of copper was installed and thermal expansion of the system was measured for the calibration. Taking into account the estimated thermal expansion of the column, thermal expansion of the rods and the container could be analyzed. Based on the correction, thermal expansion of the pebble bed was measured under compression of 0.1 MPa. Temperature of the bed was regulated from room temperature to 973 K. From the measured expansion of the bed, average thermal expansion coefficient was estimated. For the beds with different packing factors ranging from 65.5 to 68.5 %, thermal expansion coefficients were 1.4 ± 0. 10-5 K -1 . In the first measurement of the beds without pre-loading, expansion coefficients were larger for the cooling process than heating. When the beds were successively heated and cooled, the difference decreased. This means that relocation of the pebbles arises in the first heat treatment and progress of compaction is larger in the cooling process than heating. After a few heat treatments, packing states of the beds reach stable and expansion coefficients for both heat and cooling processes are close. In the case of the beds that

  1. Fluid-bed methane proposed

    Energy Technology Data Exchange (ETDEWEB)

    1981-05-01

    The first full scale plant for the production of methane from organic waste could be built in the next few years believes M.J. Nyns of the University of Louvain, Belgium, utilizing either expanded bed or fluidised bed systems, with more than one stage, in a continuous flow arrangement. Up to 8.0 m cubed gas/m cubed digester/day could be produced with residence times reduced to 34 hours.

  2. Dispersion of Bed Load Particles

    OpenAIRE

    SAWAI, Kenji

    1987-01-01

    The motion of bed load particles is so irregular that they disperse remarkably with time.In this study, some flume tests using painted tracer particles were carried out, in which thedispersive property of tracers changed variously with sediment feed rate.In analysing this process, a stochastic simulation model is proposed where it is discussedabout the degree of exposure of individual particle near the bed surface and about the variationof its pick up rate. The exponential distribution of ste...

  3. Method of working thick beds

    Energy Technology Data Exchange (ETDEWEB)

    Giezynski, A; Bialasik, A; Krawiec, A; Wylenzek, A

    1981-12-30

    The patented method of working thick coal beds in layers consists of creating in the collapsed rocks or from the fill material a bearing rock plate by strengthening these rocks with a hardening composition made of wastes of raw material, resin and water injected into the rock through wells. The difference in the suggestion is that through boreholes drilled in the lower part of the rock roofing on a previously calculated network, a solution is regularly injected which consists of dust wastes obtained in electric filters during production of clinker from mineral raw material in a quantity of 60-70% by volume, wastes of open-hearth production in a quantity of 15-20% and natural sand in a quantity of 15-20%, and water in a quantity of 35-55% of the volume of mineral components. In the second variant, the injected compostion contains: wastes from production of clinker 55-57%, open-hearth wastes 20-23%, natural sand 12-14%, asbestos fine particles 7-8% and water 38-45% of the volume of mineral components. In addition, the difference is that in the boreholes drilled in the coal block directly under the roofing, a composition is injected which consists of natural sand and catalyst in the form of powder and individually supplied liquid synthetic resin in a quantity of 3-5% by weight in relation to the sand. The hardening time with normal temperature is 1-1.5 h, after which strength is reached of 80 kg-f/cm/sup 2/.

  4. Larvae and Nests of Aculeate Hymenoptera (Hymenoptera: Aculeata) Nesting in Reed Galls Induced by Lipara spp. (Diptera: Chloropidae) with a Review of Species Recorded. Part II.

    Science.gov (United States)

    Astapenková, Alena; Heneberg, Petr; Bogusch, Petr

    2017-01-01

    The ability of aculeate Hymenoptera to utilize wetlands is poorly understood, and descriptions of their nests and developmental stages are largely absent. Here we present results based on our survey of hymenopterans using galls induced by Lipara spp. flies on common reed Phragmites australis in the years 2015-2016. We studied 20,704 galls, of which 9,446 were longitudinally cut and the brood from them reared in the laboratory, while the remaining 11,258 galls reared in rearing bags also in laboratory conditions. We recorded eight species that were previously not known to nest in reed galls: cuckoo wasps Chrysis rutilans and Trichrysis pumilionis, solitary wasps Stenodynerus chevrieranus and Stenodynerus clypeopictus, and bees Pseudoanthidium tenellum, Stelis punctulatissima, Hylaeus communis and Hylaeus confusus. Forty five species of Hymenoptera: Aculeata are known to be associated with reed galls, of which 36 make their nests there, and the other are six parasitoids of the family Chrysididae and three cuckoo bees of the genus Stelis. Of these species, Pemphredon fabricii and in southern Europe also Heriades rubicola are very common in reed galls, followed by Hylaeus pectoralis and two species of the genus Trypoxylon. We also found new host-parasite associations: Chrysis angustula in nests of Pemphredon fabricii, Chrysis rutilans in nests of Stenodynerus clypeopictus, Trichrysis pumilionis in nests of Trypoxylon deceptorium, and Stelis breviuscula in nests of Heriades rubicola. We provide new descriptions of the nests of seven species nesting in reed galls and morphology of mature larvae of eight species nesting in reed galls and two parasitoids and one nest cleptoparasite. The larvae are usually very similar to those of related species but possess characteristics that make them easy to distinguish from related species. Our results show that common reeds are not only expansive and harmful, but very important for many insect species associated with habitats

  5. Feasibility of Using Rice Hulls as Bedding for Laboratory Mice.

    Science.gov (United States)

    Carbone, Elizabeth T; Kass, Philip H; Evans, Kristin D

    2016-01-01

    Factors that are considered when selecting laboratory mouse bedding include animal health and comfort, cost, effects on personnel, and bioactive properties. Corncob is economical and facilitates low intracage ammonia but has undesirable influences on some endocrine studies. Rice hulls are an economical material that has not been well characterized as a bedding substrate. In this pilot study, we compared various aspects of bedding performance of rice hulls and other materials. On a per-volume basis, rice hulls were less absorbent than was corncob bedding. Rice hulls had higher odds than did corncob or reclaimed wood pulp of having moisture present at the bedding surface. The results of the absorbency tests coupled with the results of preliminary monitoring of intracage ammonia raised concern about the ability of rice hulls to control ammonia levels sufficiently in cages with high occupancy. However, ammonia was negligible when cages contained 5 young adult female mice. The relative expression of 3 cytochrome p450 genes was compared among mice housed on rice hulls, corncob, reclaimed wood pulp, or pine shavings. The expression of Cyp1a2 was 1.7 times higher in the livers of mice housed on rice hulls than on pine shavings, but other differences were not statistically significant. This study provides information on the merits of rice hulls as laboratory mouse bedding. Their relatively poor moisture control is a major disadvantage that might preclude their widespread use.

  6. Ammonia, Total Reduced Sulfides, and Greenhouse Gases of Pine Chip and Corn Stover Bedding Packs.

    Science.gov (United States)

    Spiehs, Mindy J; Brown-Brandl, Tami M; Parker, David B; Miller, Daniel N; Berry, Elaine D; Wells, James E

    2016-03-01

    Bedding materials may affect air quality in livestock facilities. Our objective in this study was to compare headspace concentrations of ammonia (NH), total reduced sulfides (TRS), carbon dioxide (CO), methane (CH), and nitrous oxide (NO) when pine wood chips ( spp.) and corn stover ( L.) were mixed in various ratios (0, 10, 20, 30, 40, 60, 80, and 100% pine chips) and used as bedding with manure. Air samples were collected from the headspace of laboratory-scaled bedded manure packs weekly for 42 d. Ammonia concentrations were highest for bedded packs containing 0, 10, and 20% pine chips (equivalent to 501.7, 502.3, and 502.3 mg m, respectively) in the bedding mixture and were lowest when at least 80% pine chips were used as bedding (447.3 and 431.0 mg m, respectively for 80 and 100% pine chip bedding). The highest NH concentrations were observed at Day 28. The highest concentration of TRS was observed when 100% pine chips were used as bedding (11.4 µg m), with high concentrations occurring between Days 7 and 14, and again at Day 35. Greenhouse gases were largely unaffected by bedding material but CH and CO concentrations increased as the bedded packs aged and NO concentrations were highly variable throughout the incubation. We conclude that a mixture of bedding material that contains 30 to 40% pine chips may be the ideal combination to reduce both NH and TRS emissions. All gas concentrations increased as the bedded packs aged, suggesting that frequent cleaning of facilities would improve air quality in the barn, regardless of bedding materials used. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

  7. Granular controls on the dispersion of bed load tracers

    Science.gov (United States)

    Jerolmack, D. J.; Martin, R. L.; Phillips, C. B.

    2014-12-01

    Coarse particles are transported in a river as bed load, i.e., they move in frequent contact with and are supported by the granular bed. This movement is typically intermittent and may be described by a series of steps are rests, the distributions of which determine particle dispersion. Laboratory and field studies of bed load tracer dispersion have reported sub- and super-diffusive behavior, both of which have been successfully reproduced with stochastic transport models. Although researchers have invoked heavy-tailed step lengths as the cause of anomalous dispersion, most observations report thin-tailed distributions. Little attention has been paid to rest periods, and stochastic transport models have not been connected to the underlying mechanics of particle motion. Based on theoretical and experimental evidence, we argue that step lengths are thin-tailed and do not control the longterm dispersion of bed load tracers; they are determined by momentum balance between the fluid and solid. Using laboratory experiments with both marbles and natural sediments, we demonstrate that the rest time distribution is power law, and argue that this distribution controls asymptotic dispersion. Observed rest times far exceed any hydrodynamic timescale. Experiments reveal that rest times of deposited particles are governed by fluctuations in river bed elevation; in particular, the return time for the bed to scour to the base of a deposited particle. Stochastic fluctuations in bed elevation are describable by an Ornstein-Uhlenbeck (mean-reverting random walk) model that contains two parameters, which we show are directly related to the granular shear rate and range of bed elevation fluctuations, respectively. Combining these results with the theory of asymmetric random walks (particles only move downstream), we predict superdiffusive behavior that is in quantitative agreement with our observations of tracer dispersion in a natural river.

  8. Visual observations of individual particle behaviour in gas and liquid fluidized beds

    NARCIS (Netherlands)

    Hartholt, G.P; Hoffmann, A.C; Janssen, L.P.B.M.

    The behaviour of the individual particles in dense gas and liquid fluidized beds and the behaviour of the jetsam particles in gas fluidized beds containing binary mixtures of different density group B powders has been observed. These visualizations have been made by means of an optical probe fitted

  9. Tratamento anaeróbio de pentaclorofenol em reator de leito fluidificado alimentado com água residuária sintética contendo glicose como fonte única de carbono Anaerobic treatment of pentachlorophenol in a fluidized bed reactor fed with synthetic wastewater containing glucose as a single carbon source

    Directory of Open Access Journals (Sweden)

    Flavio Bentes Freire

    2008-09-01

    Full Text Available Neste trabalho foi utilizado um reator anaeróbio de leito fluidificado (RALF, tratando água residuária sintética contendo pentaclorofenol (PCP, submetido a condições operacionais menos idealizadas. Utilizou-se um reator com volume de 16 litros, com partículas de carvão ativado granular como meio suporte. O desempenho do reator foi verificado pelas análises usuais de monitoramento (pH, alcalinidade, DQO, ácidos voláteis e também por análises de microscopia e concentração de PCP. A presença de PCP no sistema, nas concentrações utilizadas, não alterou de maneira significativa a qualidade da biomassa presente, e nem os parâmetros de monitoramento. Em concentrações afluentes de PCP variando de 1 a 6 mg/L, foram observadas eficiências médias de remoção de 92% e 70%, respectivamente.In the present work, an anaerobic fluidized bed reactor (AFBR was used for the treatment of a synthetic wastewater containing pentachlorophenol (PCP subjected to less idealized operating conditions. The reactor was a 16 litres tank with granular activated carbon particles as support media. Evaluation of AFBR performance was done by the analysis of usual monitoring parameters (pH, alkalinity, COD, volatile acids together with microscopy and PCP concentration analysis. The presence of PCP under the concentrations used did not significantly alter the amount of biomass and the performance monitoring parameters. Removal average efficiencies of the order of 92% and 70% were obtained for PCP inflow concentrations in the range of 1 to 6mg/l.

  10. An examination of fire spread thresholds in discontinuous fuel beds

    Science.gov (United States)

    Mark A. Finney; Jack D. Cohen; Isaac C. Grenfell; Kara M. Yedinak

    2010-01-01

    Many fuel beds, especially live vegetation canopies (conifer forests, shrub fields, bunch-grasses) contain gaps between vegetation clumps. Fires burning in these fuel types often display thresholds for spread that are observed to depend on environmental factors like wind, slope, and fuel moisture content. To investigate threshold spread behaviours, we conducted a set...

  11. Avoiding Carbon Bed Hot Spots in Thermal Process Off-Gas Systems

    International Nuclear Information System (INIS)

    Soelberg, Nick; Enneking, Joe

    2011-01-01

    Mercury has had various uses in nuclear fuel reprocessing and other nuclear processes, and so is often present in radioactive and mixed (radioactive and hazardous) wastes. Test programs performed in recent years have shown that mercury in off-gas streams from processes that treat radioactive wastes can be controlled using fixed beds of activated sulfur-impregnated carbon, to levels low enough to comply with air emission regulations such as the Hazardous Waste Combustor (HWC) Maximum Achievable Control Technology (MACT) standards. Carbon bed hot spots or fires have occurred several times during these tests, and also during a remediation of tanks that contained mixed waste. Hot spots occur when localized areas in a carbon bed become heated to temperatures where oxidation occurs. This heating typically occurs due to heat of absorption of gas species onto the carbon, but it can also be caused through external means such as external heaters used to heat the carbon bed vessel. Hot spots, if not promptly mitigated, can grow into bed fires. Carbon bed hot spots and fires must be avoided in processes that treat radioactive and mixed waste. Hot spots are detected by (a) monitoring in-bed and bed outlet gas temperatures, and (b) more important, monitoring of bed outlet gas CO concentrations. Hot spots are mitigated by (a) designing for appropriate in-bed gas velocity, for avoiding gas flow maldistribution, and for sufficient but not excessive bed depth, (b) appropriate monitoring and control of gas and bed temperatures and compositions, and (c) prompt implementation of corrective actions if bed hot spots are detected. Corrective actions must be implemented quickly if bed hot spots are detected, using a graded approach and sequence starting with corrective actions that are simple, quick, cause the least impact to the process, and are easiest to recover from.

  12. The impact of structural development on near bed flow dynamics in gravel bed rivers: coupling flume experiments with numerical modelling

    Science.gov (United States)

    Ockelford, A.; Hardy, R. J.; Rice, S. P.; Powell, M.

    2017-12-01

    It is increasingly being recognised that gravel bed rivers develop a surface `texture' in response to changes in the flow and sediment regime. This textural response often takes the form of a bed structure which develops to ultimately stabilise the surface across a range of spatio-temporal scales and it is these topographical structures which determine the flow structures that develop over the river bed. However, our ability to measure and parameterise that structure in ways that are useful and meaningful for the prediction of flow dynamics, still remains inadequate; this paper uses a three dimensional numerical model to assess how the temporal development of structure influences the near bed flow dynamics. Using a suite of flume based experiments a unimodal grain size distribution (σg = 1.30, D50 = 8.8mm) was exposed to three different levels of constant bed shear that produced sediment transport conditions ranging from marginal transport to conditions approaching full mobility of all size fractions. Surface structuring characteristics were measured at a high spatio-temporal resolution such that the time evolution of the beds could be fully described. In total 54 surfaces were generated and run through a Reynolds averaged three dimensional numerical model with an Rng turbulence closure. The topography input included using an immersed boundary technique within a Cartesian framework. Discussion concentrates on the how the trajectory of structural evolution under the different treatments affects the near bed flow dynamics. Specifically links are made between how the scales of boundary topography influence the flow and discusses how the measured flow variability at any one point will contain both locally derived and upstream-inherited flow structures, according to the range of scales of bed topography present. Keywords: Graded, Sediment, Structure, Turbulence, Modelling

  13. Fluid bed porosity equation for an inverse fluidized bed bioreactor with particles growing biofilm

    International Nuclear Information System (INIS)

    Campos-Diaz, K. E.; Limas-Ballesteros, R.

    2009-01-01

    Fluid Bed Bioreactor performance is strongly affected by bed void fraction or bed porosity fluctuations. Particle size enlargement due to biofilm growth is an important factor that is involved in these variations and until now there are no mathematical equations that consider biofilm growth. In this work a mathematical equation is proposed to calculate bed void fraction in an inverse fluid bed bioreactor. (Author)

  14. Clinical physiology of bed rest

    Science.gov (United States)

    Greenleaf, John E.

    1993-01-01

    Maintenance of optimal health in humans requires the proper balance between exercise, rest, and sleep as well as time in the upright position. About one-third of a lifetime is spent sleeping; and it is no coincidence that sleeping is performed in the horizontal position, the position in which gravitational influence on the body is minimal. Although enforced bed rest is necessary for the treatment of some ailments, in some cases it has probably been used unwisely. In addition to the lower hydrostatic pressure with the normally dependent regions of the cardiovascular system, body fuid compartments during bed rest in the horizontal body position, and virtual elimination of compression on the long bones of the skeletal system during bed rest (hypogravia), there is often reduction in energy metabolism due to the relative confinement (hypodynamia) and alteration of ambulatory circadian variations in metabolism, body temperature, and many hormonal systems. If patients are also moved to unfamiliar surroundings, they probably experience some feelings of anxiety and some sociopsychological problems. Adaptive physiological responses during bed rest are normal for that environment. They are attempts by the body to reduce unnecessary energy expenditure, to optimize its function, and to enhance its survival potential. Many of the deconditioning responses begin within the first day or two of bed rest; these early responses have prompted physicians to insist upon early resumption of the upright posture and ambulation of bedridden patients.

  15. Identification, synthesis and mass spectrometry of a macrolide from the African reed frog Hyperolius cinnamomeoventris

    Directory of Open Access Journals (Sweden)

    Markus Menke

    2016-12-01

    Full Text Available The contents of the gular glands of the male African reed frog Hyperolius cinnamomeoventris consist of a mixture of aliphatic macrolides and sesquiterpenes. While the known macrolide gephyromantolide A was readily identified, the structure of another major component was suggested to be a tetradecen-13-olide. The synthesis of the two candidate compounds (Z-5- and (Z-9-tetradecen-13-olide revealed the former to be the naturally occurring compound. The synthesis used ring-closing metathesis as key step. While the Hoveyda–Grubbs catalyst furnished a broad range of isomeric products, the (Z-selective Grubbs catalyst lead to pure (Z-products. Analysis by chiral GC revealed the natural frog compound to be (5Z,13S-5-tetradecen-13-olide (1. This compound is also present in the secretion of other hyperoliid frogs as well as in femoral glands of male mantellid frogs such as Spinomantis aglavei. The mass spectra of the synthesized macrolides as well as their rearranged isomers obtained during ring-closing metathesis showed that it is possible to assign the location of the double bond in an unsaturated macrolide on the basis of its EI mass spectrum. The occurrence of characteristic ions can be explained by the fragmentation pathway proposed in the article. In contrast, the localization of a double bond in many aliphatic open-chain compounds like alkenes, alcohols or acetates, important structural classes of pheromones, is usually not possible from an EI mass spectrum. In the article, we present the synthesis and for the first time elucidate the structure of macrolides from the frog family Hyperoliidae.

  16. Survival during the Breeding Season: Nest Stage, Parental Sex, and Season Advancement Affect Reed Warbler Survival.

    Directory of Open Access Journals (Sweden)

    Kaja Wierucka

    Full Text Available Avian annual survival has received much attention, yet little is known about seasonal patterns in survival, especially of migratory passerines. In order to evaluate survival rates and timing of mortality within the breeding season of adult reed warblers (Acrocephalus scirpaceus, mark-recapture data were collected in southwest Poland, between 2006 and 2012. A total of 612 individuals (304 females and 308 males were monitored throughout the entire breeding season, and their capture-recapture histories were used to model survival rates. Males showed higher survival during the breeding season (0.985, 95% CI: 0.941-0.996 than females (0.869, 95% CI: 0.727-0.937. Survival rates of females declined with the progression of the breeding season (from May to August, while males showed constant survival during this period. We also found a clear pattern within the female (but not male nesting cycle: survival was significantly lower during the laying, incubation, and nestling periods (0.934, 95% CI: 0.898-0.958, when birds spent much time on the nest, compared to the nest building and fledgling periods (1.000, 95% CI: 1.00-1.000, when we did not record any female mortality. These data (coupled with some direct evidence, like bird corpses or blood remains found next to/on the nest may suggest that the main cause of adult mortality was on-nest predation. The calculated survival rates for both sexes during the breeding season were high compared to annual rates reported for this species, suggesting that a majority of mortality occurs at other times of the year, during migration or wintering. These results have implications for understanding survival variation within the reproductive period as well as general trends of avian mortality.

  17. Modes of heat removal from a heat-generating debris bed

    International Nuclear Information System (INIS)

    Squarer, D.; Hochreiter, L.E.; Piecznski, A.T.

    1984-01-01

    In the worst hypothetical accident in a light water reactor, when all protection systems fail, the core could be converted into a deep particulate bed either in-vessel or ex-vessel. The containment of such an accident depends on the coolability of a heat-generating debris bed. Some recent experimental and analytical studies that are concerned with heat removal from such a particulate bed are reviewed. Studies have indicated that bed dryout flux and, therefore, the heat removal rate from the particulate bed increases with the particle diameter (i.e., the permeability) for pool boiling conditions and can exceed the critical heat flux of a flat plate. Bed dryout in a large particle bed (i.e., a few millimetres) was found to be closely related to the ''flooding'' limit of the bed. Dryout under forced flow conditions was found to be affected by both forced and natural convection for mass flow rate smaller than m /SUB cr/ , whereas above this mass flow rate, bed dryout is proportional to the mass flow rate. Recent analyses were found to be in agreement with experimental data; however, additional research is needed to assess factors not accounted for in previous studies (e.g., effect of pressure, multidimensionality, stratification, etc.). Based on the expected pressure and particle sizes in a postulated severe accident sequence, a debris bed should be coolable, given a sufficient water supply

  18. Effect of 2 Bedding Materials on Ammonia Levels in Individually Ventilated Cages.

    Science.gov (United States)

    Koontz, Jason M; Kumsher, David M; Kelly, Richard; Stallings, Jonathan D

    2016-01-01

    This study sought to identify an optimal rodent bedding and cage-change interval to establish standard procedures for the IVC in our rodent vivarium. Disposable cages were prefilled with either corncob or α-cellulose bedding and were used to house 2 adult Sprague-Dawley rats (experimental condition) or contained no animals (control). Rats were observed and intracage ammonia levels measured daily for 21 d. Intracage ammonia accumulation became significant by day 8 in experimental cages containing α-cellulose bedding, whereas experimental cages containing corncob bedding did not reach detectable levels of ammonia until day 14. In all 3 experimental cages containing α-cellulose, ammonia exceeded 100 ppm (our maximum acceptable limit) by day 11. Two experimental corncob cages required changing at days 16 and 17, whereas the remaining cage containing corncob bedding lasted the entire 21 d without reaching the 100-ppm ammonia threshold. These data suggests that corncob bedding provides nearly twice the service life of α-cellulose bedding in the IVC system.

  19. The Effects of Supplementary Food on the Breeding Performance of Eurasian Reed Warblers Acrocephalus scirpaceus; Implications for Climate Change Impacts.

    Directory of Open Access Journals (Sweden)

    James O Vafidis

    Full Text Available Understanding the mechanisms by which climate variation can drive population changes requires information linking climate, local conditions, trophic resources, behaviour and demography. Climate change alters the seasonal pattern of emergence and abundance of invertebrate populations, which may have important consequences for the breeding performance and population change of insectivorous birds. In this study, we examine the role of food availability in driving behavioural changes in an insectivorous migratory songbird; the Eurasian reed warbler Acrocephalus scirpaceus. We use a feeding experiment to examine the effect of increased food supply on different components of breeding behaviour and first-brood productivity, over three breeding seasons (2012-2014. Reed warblers respond to food-supplementation by advancing their laying date by up to 5.6 days. Incubation periods are shorter in supplemented groups during the warmest mean spring temperatures. Nestling growth rates are increased in nests provisioned by supplemented parents. In addition, nest predation is reduced, possibly because supplemented adults spend more time at the nest and faster nestling growth reduces the period of vulnerability of eggs and nestlings to predators (and brood parasites. The net effect of these changes is to advance the fledging completion date and to increase the overall productivity of the first brood for supplemented birds. European populations of reed warblers are currently increasing; our results suggest that advancing spring phenology, leading to increased food availability early in the breeding season, could account for this change by facilitating higher productivity. Furthermore, the earlier brood completion potentially allows multiple breeding attempts. This study identifies the likely trophic and behavioural mechanisms by which climate-driven changes in invertebrate phenology and abundance may lead to changes in breeding phenology, nest survival and net

  20. Design experiments for a vented containment

    International Nuclear Information System (INIS)

    Hesboel, R.

    1985-01-01

    A filtered containment venting system, operable late in 1985, is currently under installation at the Barsebaeck twin nuclear power station in Sweden. The filter unit, which communicates with the containments of both reactor units, but is separated from them by rupture discs, consists of a concrete bed, 40 m high and 20 m in diameter, filled with gravel of grain size 25-35 mm. The performance of the gravel bed under such accident conditions which might lead to an activation of this safeguard system has been the subject for investigation within the FILTRA project. These investigations have shown that the gravel bed acts as: an expansion volume for decreasing gas pressure and increasing gas residence time, a heat sink for condensing steam, an excellent filter medium for removing aerosols and elemental iodine, and a sump volume for collecting radioactive condensate. The results from iodine retention studies in gravel beds are mainly considered

  1. Particle Bed Reactor scaling relationships

    International Nuclear Information System (INIS)

    Slovik, G.; Araj, K.; Horn, F.L.; Ludewig, H.; Benenati, R.

    1987-01-01

    Scaling relationships for Particle Bed Reactors (PBRs) are discussed. The particular applications are short duration systems, i.e., for propulsion or burst power. Particle Bed Reactors can use a wide selection of different moderators and reflectors and be designed for such a wide range of power and bed power densities. Additional design considerations include the effect of varying the number of fuel elements, outlet Mach number in hot gas channel, etc. All of these variables and options result in a wide range of reactor weights and performance. Extremely light weight reactors (approximately 1 kg/MW) are possible with the appropriate choice of moderator/reflector and power density. Such systems are very attractive for propulsion systems where parasitic weight has to be minimized

  2. Do females invest more into eggs when males sing more attractively? Postmating sexual selection strategies in a monogamous reed passerine

    OpenAIRE

    Krištofík, Ján; Darolová, Alžbeta; Majtan, Juraj; Okuliarová, Monika; Zeman, Michal; Hoi, Herbert

    2014-01-01

    Maternal investment can play an important role for offspring fitness, especially in birds, as females have to provide their eggs with all the necessary nutrients for the development of the embryo. It is known that this type of maternal investment can be influenced by the quality of the male partner. In this study, we first verify that male song is important in the mate choice of female Eurasian reed warblers, as males mate faster when their singing is more complex. Furthermore, female egg inv...

  3. Nitrosomonas communis strain YNSRA, an ammonia-oxidizing bacterium, isolated from the reed rhizoplane in an aquaponics plant.

    Science.gov (United States)

    Tokuyama, Tatsuaki; Mine, Atsusi; Kamiyama, Kaoru; Yabe, Ryuichi; Satoh, Kazuo; Matsumoto, Hirotoshi; Takahashi, Reiji; Itonaga, Koji

    2004-01-01

    An ammonia-oxidizing bacterium (strain YNSRA) was isolated from the rhizoplane of the reed (Phragmites communis) used in an aquaponics plant which is a wastewater treatment plant. Strain YNSRA was identified as Nitrosomonas communis by taxonomic studies. The hydroxylamine-cytochrome c reductase (HCR) of strain YNSRA was found to have a higher activity (25.60 u/mg) than that of Nitrosomonas europaea ATCC25978T (8.94 u/mg). Ribulose-1,5-bisphosphate carboxylase (RubisCO) activity was detected at very low levels in strain YNSRA, whereas strain ATCC25978T had definite activity.

  4. Management and characteristics of recycled manure solids used for bedding in Midwest freestall dairy herds.

    Science.gov (United States)

    Husfeldt, A W; Endres, M I; Salfer, J A; Janni, K A

    2012-04-01

    Interest in using recycled manure solids (RMS) as a bedding material for dairy cows has grown in the US Midwest. Cost of common bedding materials has increased in recent years and availability has decreased. Information regarding the composition of RMS and its use as a bedding material for dairy cows in the Midwest is very limited. The objectives of this study were to characterize RMS as a bedding material, observe bedding management practices, document methods of obtaining RMS, and describe housing facilities. We visited 38 Midwest dairy operations bedding freestalls with RMS to collect data. Methods of obtaining RMS for bedding included separation of anaerobic digested manure, separation of raw manure, and separation of raw manure followed by mechanical drum-composting for 18 to 24 h. Average bedding moisture of unused RMS was 72.4% with a pH of 9.16. Unused samples contained (on a dry basis) 1.4% N, 44.9% C, 32.7C:N ratio, 0.44% P, 0.70% K, 76.5% neutral detergent fiber, 9.4% ash, 4.4% nonfiber carbohydrates, and 1.1% fat. Moisture was lowest for drum-composted solids before and after use as freestall bedding. After use in the stalls, digested solids had lower neutral detergent fiber content (70.5%) than drum-composted (75.0%) and separated raw (73.1%) solids. Total N content was greater in digested solids (2.0%) than in separated raw (1.7%) solids. Total bacterial populations in unused bedding were greatest in separated raw manure solids but were similar between digested and drum-composted manure solids. Drum-composted manure solids had no coliform bacteria before use as freestall bedding. After use as bedding, digested manure solids had lower total bacteria counts compared with drum-composted and separated raw manure solids, which had similar counts. Used bedding samples of digested solids contained fewer environmental streptococci than drum-composted and separated raw solids and had reduced Bacillus counts compared with separated raw solids. Coliform counts

  5. Prediction of bed level variations in nonuniform sediment bed channel

    Indian Academy of Sciences (India)

    B R Andharia

    2018-04-12

    Apr 12, 2018 ... A fully-coupled 1D mobile-bed model (CAR-. ICHAR) was introduced ...... for sediment trap, water level sensor, tail gate operated by lever arm at .... materials were brought back to upstream to feed the same through sediment ...

  6. Acidification of calf bedding reduces fly development and bacterial abundance.

    Science.gov (United States)

    Calvo, M S; Gerry, A C; McGarvey, J A; Armitage, T L; Mitloehner, F M

    2010-03-01

    Environmental stressors, such as high fly density, can affect calf well-being. Sodium bisulfate (SBS) is an acidifier that reduces the pH of flooring and bedding, creating a medium that neither bacteria nor immature flies (also known as larvae or maggots) can thrive in. Two experiments were conducted to investigate the application of SBS to a mixture of rice hull calf bedding and calf slurry (BED) to reduce house fly (Musca domestica L.) larval density and the abundance of bacteria. In experiment 1, dish pans containing 1L of BED and 3,000 house fly eggs were treated with SBS at concentrations of 0, 8.9, 17.7, and 26.5g of SBS/0.05m(2) of BED (CON, LOW, MED, and HIGH, respectively), with each SBS concentration applied to 4 individual pans (16 pans total). Reapplication of the same SBS concentrations in each pan occurred 3 times/wk throughout the 23-d trial. Larval house fly survival was significantly reduced in all pans with SBS relative to CON pans, with lowest survival rates in the MED and HIGH pans (99% and 100% reduction, respectively). The mean pH for each treatment was inversely related to the SBS concentration. In experiment 2, pans containing 1L of BED and 3,000 house fly eggs were treated with either 0g of SBS (CON), 8.9g of SBS/0.05m(2) of BED with reapplication of the acidifier 3 times/wk (SB3x), or 8.9g of SBS/0.05m(2) of BED applied only once at 48h before the end of the 8 d-trial (SB48). Larval house fly survival and bacterial concentrations were reduced (90% larval reduction and 68% bacterial reduction) in the SB3x treatment relative to the CON. Mean pH was also reduced in SB3x pans relative to CON or SB48 pans. Overall, acidification of calf BED using the acidifier SBS resulted in a reduction of bacteria and house fly larval survival. This form of fly control might be expected to reduce adult fly production and, therefore, fly-related stress in calves.

  7. The SSM/PMAD automated test bed project

    Science.gov (United States)

    Lollar, Louis F.

    1991-01-01

    The Space Station Module/Power Management and Distribution (SSM/PMAD) autonomous subsystem project was initiated in 1984. The project's goal has been to design and develop an autonomous, user-supportive PMAD test bed simulating the SSF Hab/Lab module(s). An eighteen kilowatt SSM/PMAD test bed model with a high degree of automated operation has been developed. This advanced automation test bed contains three expert/knowledge based systems that interact with one another and with other more conventional software residing in up to eight distributed 386-based microcomputers to perform the necessary tasks of real-time and near real-time load scheduling, dynamic load prioritizing, and fault detection, isolation, and recovery (FDIR).

  8. PIV Visualization of Bubble Induced Flow Circulation in 2-D Rectangular Pool for Ex-Vessel Debris Bed Coolability

    Energy Technology Data Exchange (ETDEWEB)

    Han, Teayang; Kim, Eunho; Park, Hyun Sun; Moriyama, Kiyofumi [POSTECH, Pohang (Korea, Republic of)

    2015-10-15

    The previous research works demonstrated the debris bed formation on the flooded cavity floor in experiments. Even in the cases the core melt is once solidified, the debris bed can be re-melted due to the decay heat. If the debris bed is not cooled enough by the coolant, the re-melted debris bed will react with the concrete base mat. This situation is called the molten core-concrete interaction (MCCI) which threatens the integrity of the containment by generated gases which pressurize the containment. Therefore securing the long term coolability of the debris bed in the cavity is crucial. According to the previous research works, the natural convection driven by the rising bubbles affects the coolability and the formation of the debris bed. Therefore, clarification of the natural convection characteristics in and around the debris bed is important for evaluation of the coolability of the debris bed. In this study, two-phase flow around the debris bed in a 2D slice geometry is visualized by PIV method to obtain the velocity map of the flow. The DAVINCI-PIV was developed to investigate the flow around the debris bed. In order to simulate the boiling phenomena induced by the decay heat of the debris bed, the air was injected separately by the air chamber system which consists of the 14 air-flowmeters. The circulation flow developed by the rising bubbles was visualized by PIV method.

  9. Apparatus and process for controlling fluidized beds

    Science.gov (United States)

    Rehmat, Amirali G.; Patel, Jitendra G.

    1985-10-01

    An apparatus and process for control and maintenance of fluidized beds under non-steady state conditions. An ash removal conduit is provided for removing solid particulates from a fluidized bed separate from an ash discharge conduit in the lower portion of the grate supporting such a bed. The apparatus and process of this invention is particularly suitable for use in ash agglomerating fluidized beds and provides control of the fluidized bed before ash agglomeration is initiated and during upset conditions resulting in stable, sinter-free fluidized bed maintenance.

  10. Method of Heating a Foam-Based Catalyst Bed

    Science.gov (United States)

    Fortini, Arthur J.; Williams, Brian E.; McNeal, Shawn R.

    2009-01-01

    A method of heating a foam-based catalyst bed has been developed using silicon carbide as the catalyst support due to its readily accessible, high surface area that is oxidation-resistant and is electrically conductive. The foam support may be resistively heated by passing an electric current through it. This allows the catalyst bed to be heated directly, requiring less power to reach the desired temperature more quickly. Designed for heterogeneous catalysis, the method can be used by the petrochemical, chemical processing, and power-generating industries, as well as automotive catalytic converters. Catalyst beds must be heated to a light-off temperature before they catalyze the desired reactions. This typically is done by heating the assembly that contains the catalyst bed, which results in much of the power being wasted and/or lost to the surrounding environment. The catalyst bed is heated indirectly, thus requiring excessive power. With the electrically heated catalyst bed, virtually all of the power is used to heat the support, and only a small fraction is lost to the surroundings. Although the light-off temperature of most catalysts is only a few hundred degrees Celsius, the electrically heated foam is able to achieve temperatures of 1,200 C. Lower temperatures are achievable by supplying less electrical power to the foam. Furthermore, because of the foam s open-cell structure, the catalyst can be applied either directly to the foam ligaments or in the form of a catalyst- containing washcoat. This innovation would be very useful for heterogeneous catalysis where elevated temperatures are needed to drive the reaction.

  11. Core catcher for nuclear reactor core meltdown containment

    International Nuclear Information System (INIS)

    Driscoll, M.J.; Bowman, F.L.

    1978-01-01

    A bed of graphite particles is placed beneath a nuclear reactor core outside the pressure vessel but within the containment building to catch the core debris in the event of failure of the emergency core cooling system. Spray cooling of the debris and graphite particles together with draining and flooding of coolant fluid of the graphite bed is provided to prevent debris slump-through to the bottom of the bed

  12. Determination of electrical resistivity of dry coke beds

    Energy Technology Data Exchange (ETDEWEB)

    Eidem, P.A.; Tangstad, M.; Bakken, J.A. [NTNU, Trondheim (Norway)

    2008-02-15

    The electrical resistivity of the coke bed is of great importance when producing FeMn, SiMn, and FeCr in a submerged arc furnace. In these processes, a coke bed is situated below and around the electrode tip and consists of metallurgical coke, slag, gas, and metal droplets. Since the basic mechanisms determining the electrical resistivity of a coke bed is not yet fully understood, this investigation is focused on the resistivity of dry coke beds consisting of different carbonaceous materials, i.e., coke beds containing no slag or metal. A method that reliably compares the electrical bulk resistivity of different metallurgical cokes at 1500{sup o} C to 1600{sup o}C is developed. The apparatus is dimensioned for industrial sized materials, and the electrical resistivity of anthracite, charcoal, petroleum coke, and metallurgical coke has been measured. The resistivity at high temperatures of the Magnitogorsk coke, which has the highest resistivity of the metallurgical cokes investigated, is twice the resistivity of the Corus coke, which has the lowest electrical resistivity. Zdzieszowice and SSAB coke sort in between with decreasing resistivities in the respective order. The electrical resistivity of anthracite, charcoal, and petroleum coke is generally higher than the resistivity of the metallurgical cokes, ranging from about two to about eight times the resistivity of the Corus coke at 1450{sup o}C. The general trend is that the bulk resistivity of carbon materials decreases with increasing temperature and increasing particle size.

  13. Physiology Of Prolonged Bed Rest

    Science.gov (United States)

    Greenleaf, John E.

    1991-01-01

    Report describes physiological effects of prolonged bed rest. Rest for periods of 24 hours or longer deconditions body to some extent; healing proceeds simultaneously with deconditioning. Report provides details on shifts in fluid electrolytes and loss of lean body mass, which comprises everything in body besides fat - that is, water, muscle, and bone. Based on published research.

  14. How to Find Bed Bugs

    Science.gov (United States)

    Find and correctly identify an infestation early before it becomes widespread. Look for rusty or reddish stains and pinpoint dark spots on bed sheets or mattresses, and search for bugs near the piping, seams and tags of the mattress and box spring.

  15. Dale Reed with model in front of M2-F1

    Science.gov (United States)

    1967-01-01

    Dale Reed with a model of the M2-F1 in front of the actual lifting body. Reed used the model to show the potential of the lifting bodies. He first flew it into tall grass to test stability and trim, then hand-launched it from buildings for longer flights. Finally, he towed the lifting-body model aloft using a powered model airplane known as the 'Mothership.' A timer released the model and it glided to a landing. Dale's wife Donna used a 9 mm. camera to film the flights of the model. Its stability as it glided--despite its lack of wings--convinced Milt Thompson and some Flight Research Center engineers including the center director, Paul Bikle, that a piloted lifting body was possible. The lifting body concept evolved in the mid-1950s as researchers considered alternatives to ballistic reentries of piloted space capsules. The designs for hypersonic, wingless vehicles were on the boards at NASA Ames and NASA Langley facilities, while the US Air Force was gearing up for its Dyna-Soar program, which defined the need for a spacecraft that would land like an airplane. Despite favorable research on lifting bodies, there was little support for a flight program. Dryden engineer R. Dale Reed was intrigued with the lifting body concept, and reasoned that some sort of flight demonstration was needed before wingless aircraft could be taken seriously. In February 1962, he built a model lifting body based upon the Ames M2 design, and air-launched it from a radio controlled 'mothership.' Home movies of these flights, plus the support of research pilot Milt Thompson, helped pursuade the facilities director, Paul Bikle, to give the go-ahead for the construction of a full-scale version, to be used as a wind-tunnel model and possibly flown as a glider. Comparing lifting bodies to space capsules, an unofficial motto of the project was, 'Don't be Rescued from Outer Space--Fly Back in Style.' The construction of the M2-F1 was a joint effort by Dryden and a local glider manufacturer, the

  16. The NASA Bed Rest Project

    Science.gov (United States)

    Rhodes, Bradley; Meck, Janice

    2005-01-01

    NASA s National Vision for Space Exploration includes human travel beyond low earth orbit and the ultimate safe return of the crews. Crucial to fulfilling the vision is the successful and timely development of countermeasures for the adverse physiological effects on human systems caused by long term exposure to the microgravity environment. Limited access to in-flight resources for the foreseeable future increases NASA s reliance on ground-based analogs to simulate these effects of microgravity. The primary analog for human based research will be head-down bed rest. By this approach NASA will be able to evaluate countermeasures in large sample sizes, perform preliminary evaluations of proposed in-flight protocols and assess the utility of individual or combined strategies before flight resources are requested. In response to this critical need, NASA has created the Bed Rest Project at the Johnson Space Center. The Project establishes the infrastructure and processes to provide a long term capability for standardized domestic bed rest studies and countermeasure development. The Bed Rest Project design takes a comprehensive, interdisciplinary, integrated approach that reduces the resource overhead of one investigator for one campaign. In addition to integrating studies operationally relevant for exploration, the Project addresses other new Vision objectives, namely: 1) interagency cooperation with the NIH allows for Clinical Research Center (CRC) facility sharing to the benefit of both agencies, 2) collaboration with our International Partners expands countermeasure development opportunities for foreign and domestic investigators as well as promotes consistency in approach and results, 3) to the greatest degree possible, the Project also advances research by clinicians and academia alike to encourage return to earth benefits. This paper will describe the Project s top level goals, organization and relationship to other Exploration Vision Projects, implementation

  17. Shielding container

    International Nuclear Information System (INIS)

    Darling, K.A.M.

    1981-01-01

    A shielding container incorporates a dense shield, for example of depleted uranium, cast around a tubular member of curvilinear configuration for accommodating a radiation source capsule. A lining for the tubular member, in the form of a close-coiled flexible guide, provides easy replaceability to counter wear while the container is in service. Container life is extended, and maintenance costs are reduced. (author)

  18. A bit faster : ReedHycalog focuses new drill bit technology on the needs of western Canadian drillers

    Energy Technology Data Exchange (ETDEWEB)

    Wells, P.

    2009-06-15

    ReedHycalog, a division of National Oilwell Varco Inc., is advancing its drill bit technology and is setting performance records in an effort to meet the needs of drillers in western Canada. This article described the company's new drill bit technology. Through its motor series polycrystalline diamond cutter (PDC) bits, ReedHycalog developed and commercialized several unique and proprietary drill bit features that reduced variations in torque. This lowered the risk of stick-slip while improving lateral stability, directional control and drilling efficiency. The design of the motor series bits was reviewed along with laboratory and field testing. Smooth torque was identified as one of the greatest challenges when drilling with a drill bit on a directional assembly. Test results revealed that there are 4 distinct characteristics for optimal steerable motor performance, such as smooth torque control components (TCC) that were specifically positioned in the cone of the bit to prevent cutter over engagement reducing in torque fluctuations for optimal tool face control; optimized cutter backrakes that provided high penetration rates in rotating mode, while TCCs were optimized to control torque when sliding; gauge inserts for lateral control that provided a low-friction bearing surface; and laterally exposed gauge cutters that cleaned up the hole in rotating mode, and a tapered upper section that reduced gauge pad interference while in sliding mode. The motor series bits performed extremely well in the vertical, build and horizontal intervals with multiple operators. 1 ref., 3 figs.

  19. Database of the Geologic Map of North America - Adapted from the Map by J.C. Reed, Jr. and others (2005)

    Science.gov (United States)

    Garrity, Christopher P.; Soller, David R.

    2009-01-01

    The Geological Society of America's (GSA) Geologic Map of North America (Reed and others, 2005; 1:5,000,000) shows the geology of a significantly large area of the Earth, centered on North and Central America and including the submarine geology of parts of the Atlantic and Pacific Oceans. This map is now converted to a Geographic Information System (GIS) database that contains all geologic and base-map information shown on the two printed map sheets and the accompanying explanation sheet. We anticipate this map database will be revised at some unspecified time in the future, likely through the actions of a steering committee managed by the Geological Society of America (GSA) and staffed by scientists from agencies including, but not limited to, those responsible for the original map compilation (U.S. Geological Survey, Geological Survey of Canada, and Woods Hole Oceanographic Institute). Regarding the use of this product, as noted by the map's compilers: 'The Geologic Map of North America is an essential educational tool for teaching the geology of North America to university students and for the continuing education of professional geologists in North America and elsewhere. In addition, simplified maps derived from the Geologic Map of North America are useful for enlightening younger students and the general public about the geology of the continent.' With publication of this database, the preparation of any type of simplified map is made significantly easier. More important perhaps, the database provides a more accessible means to explore the map information and to compare and analyze it in conjunction with other types of information (for example, land use, soils, biology) to better understand the complex interrelations among factors that affect Earth resources, hazards, ecosystems, and climate.

  20. Adult Bed-Wetting: A Concern?

    Science.gov (United States)

    Adult bed-wetting: A concern? My 24-year-old husband has started to wet the bed at ... of Privacy Practices Notice of Nondiscrimination Manage Cookies Advertising Mayo Clinic is a not-for-profit organization ...

  1. Find a Bed Bug Pesticide Product

    Science.gov (United States)

    Introduces the Bed Bug Product Search Tool, to help consumers find EPA-registered pesticides for bed bug infestation control. Inclusion in this database is not an endorsement. Always follow label directions carefully.

  2. EPA-Registered Bed Bug Products

    Science.gov (United States)

    ... rest or hide in hampers, bed frames, even furniture); Failing to treat adjacent areas where bed bugs ... to work (some pesticides, such as desiccators or growth regulators, may be very effective but take some ...

  3. Bed Bug Guidance for School Nurses

    Science.gov (United States)

    School nurses are often called upon to provide vital information to students, parents, teachers, and administrators. These tips on identifying, managing and preventing bed bugs will help you to effectively respond if bed bugs appear in your school.

  4. Reactor container

    International Nuclear Information System (INIS)

    Ichiki, Tadaharu; Saba, Kazuhisa.

    1979-01-01

    Purpose: To improve the earthquake resistance as well as reduce the size of a container for a nuclear reactor with no adverse effects on the decrease of impact shock to the container and shortening of construction step. Constitution: Reinforcing profile steel materials are welded longitudinally and transversely to the inner surface of a container, and inner steel plates are secured to the above profile steel materials while keeping a gap between the materials and the container. Reactor shielding wall planted to the base concrete of the container is mounted to the pressure vessel, and main steam pipeways secured by the transverse beams and led to the outside of container is connected. This can improve the rigidity earthquake strength and the safetiness against the increase in the inside pressure upon failures of the container. (Yoshino, Y.)

  5. Bacillus cereus in free-stall bedding.

    Science.gov (United States)

    Magnusson, M; Svensson, B; Kolstrup, C; Christiansson, A

    2007-12-01

    To increase the understanding of how different factors affect the bacterial growth in deep sawdust beds for dairy cattle, the microbiological status of Bacillus cereus and coliforms in deep sawdust-bedded free stalls was investigated over two 14-d periods on one farm. High counts of B. cereus and coliforms were found in the entire beds. On average, 4.1 log(10) B. cereus spores, 5.5 log(10) B. cereus, and 6.7 log(10) coliforms per gram of bedding could be found in the upper layers of the sawdust likely to be in contact with the cows' udders. The highest counts of B. cereus spores, B. cereus, and coliforms were found in the bedding before fresh bedding was added, and the lowest immediately afterwards. Different factors of importance for the growth of B. cereus in the bedding material were explored in laboratory tests. These were found to be the type of bedding, pH, and the type and availability of nutrients. Alternative bedding material such as peat and mixtures of peat and sawdust inhibited the bacterial growth of B. cereus. The extent of growth of B. cereus in the sawdust was increased in a dose-dependent manner by the availability of feces. Urine added to different bedding material raised the pH and also led to bacterial growth of B. cereus in the peat. In sawdust, a dry matter content greater than 70% was needed to lower the water activity to 0.95, which is needed to inhibit the growth of B. cereus. In an attempt to reduce the bacterial growth of B. cereus and coliforms in deep sawdust beds on the farm, the effect of giving bedding daily or a full replacement of the beds was studied. The spore count of B. cereus in the back part of the free stalls before fresh bedding was added was 0.9 log units lower in stalls given daily bedding than in stalls given bedding twice weekly. No effect on coliform counts was found. Replacement of the entire sawdust bedding had an effect for a short period, but by 1 to 2 mo after replacement, the counts of B. cereus spores in the

  6. Preliminary results from initial in-pile debris bed experiments

    International Nuclear Information System (INIS)

    Rivard, J.B.

    1977-01-01

    An accident in a liquid metal fast breeder reactor (LMFBR) in which molten core material is suddenly quenched with subcooled liquid sodium could result in extensive fragmentation and dispersal of fuel as subcritical beds of frozen particulate debris within the reactor vessel. Since this debris will continue to generate power due to decay of retained fission products, containment of the debris is threatened if the generated heat is not removed. Therefore, the initial safety question is the capacity which debris beds may have for transfer of the decay heat to overlying liquid sodium by natural processes--i.e., without the aid of forced circulation of the coolant. Up to the present time, all experiments on debris bed behavior either have used substitute materials (e.g., sand and water) or have employed actual materials, but atypical heating methods. Increased confidence in the applicability of debris bed simulations is afforded if the heat is generated within the fuel component of the appropriate fast reactor materials. The initial series of in-pile tests reported on herein constitutes the first experiments in which the internal heating mode has been produced in particulate oxide fuel immersed in liquid sodium. Fission heating of the fully-enriched UO 2 in the experiment while it is contained within Sandia Laboratories Annular Core Pulse Reactor (ACPR), operating in its steady-state mode, approximates the decay heating of debris. Preliminary results are discussed

  7. Sodium/water pool-deposit bed model of the CONACS code

    International Nuclear Information System (INIS)

    Peak, R.D.

    1983-01-01

    A new Pool-Bed model of the CONACS (Containment Analysis Code System) code represents a major advance over the pool models of other containment analysis code (NABE code of France, CEDAN code of Japan and CACECO and CONTAIN codes of the United States). This new model advances pool-bed modeling because of the number of significant materials and processes which are included with appropriate rigor. This CONACS pool-bed model maintains material balances for eight chemical species (C, H 2 O, Na, NaH, Na 2 O, Na 2 O 2 , Na 2 CO 3 and NaOH) that collect in the stationary liquid pool on the floor and in the desposit bed on the elevated shelf of the standard CONACS analysis cell

  8. Experimental Determination of Bed Conditions in Concentrated Pyroclastic Density Currents

    Science.gov (United States)

    Winner, A.; Ferrier, K.; Dufek, J.

    2016-12-01

    Pyroclastic density currents (PDCs) are ground-hugging mixtures of hot gas and rock that can reach temperatures > 800 oC and speeds of 200 m/s. These flows are capable of eroding and entraining the underlying bed material into the flow, which can strongly influence flow momentum, runout distance, and hazards associated with PDCs. However, the mechanism of erosion remains poorly constrained, with proposed mechanisms including under-pressure following the head of the fluidized current, force chain enhanced stresses at the bed, and discrete particle impacts and friction. The interactions between PDCs and the bed have been difficult to observe in the field, as their infrequent occurrence, opacity, and hostile environment make real-time measurement difficult. This study is aimed at obtaining a better understanding of the interactions between PDCs and the bed through a quantitative analysis of bed forces. Our experimental apparatus consists of a rotating cylindrical flume of radius 22 cm, within which gas-rich granular material flows along the interior of the cylinder as it rotates. By using a rotating cylinder, we are able to simulate long-duration flows, allowing us to observe impact forces at the bed over timescales comparable to the flow duration of natural PDCs. To measure the distribution and evolution of forces imparted by the flow on the bed, we constructed a cylindrical insert with a non-erodible bed in which we embedded force sensor arrays parallel and perpendicular to the direction of flow. To measure the forces felt by the particles in the flow, we added "smart particles" 25 to 50 mm in diameter to the flow. Each smart particle contains a three-axis accelerometer and a micro SD card enclosed in a spherical plastic casing, and possesses a density similar to that of the pumice in the experimental flow. Each smart particle also contains a three-axis magnetometer which permits its location to be tracked by means of a unique applied magnetic field. Ultimately

  9. Fluidization quality analyzer for fluidized beds

    Science.gov (United States)

    Daw, C.S.; Hawk, J.A.

    1995-07-25

    A control loop and fluidization quality analyzer for a fluidized bed utilizes time varying pressure drop measurements. A fast-response pressure transducer measures the overall bed pressure drop, or over some segment of the bed, and the pressure drop signal is processed to produce an output voltage which changes with the degree of fluidization turbulence. 9 figs.

  10. Fluidized bed dry dense medium coal beneficiation

    CSIR Research Space (South Africa)

    North, Brian C

    2017-10-01

    Full Text Available medium beneficiation using a fluidized bed was investigated. Bed materials of sand, magnetite and ilmenite were used in a laboratory sized cylindrical fluidized bed. The materials were individually tested, as were mixes of sand and heavy minerals. Coal...

  11. Reactor container

    International Nuclear Information System (INIS)

    Naruse, Yoshihiro.

    1990-01-01

    The thickness of steel shell plates in a reactor container embedded in sand cussions is monitored to recognize the corrosion of the steel shell plates. That is, the reactor pressure vessel is contained in a reactor container shell and the sand cussions are disposed on the lower outside of the reactor container shell to elastically support the shell. A pit is disposed at a position opposing to the sand cussions for measuring the thickness of the reactor container shell plates. The pit is usually closed by a closing member. In the reactor container thus constituted, the closing member can be removed upon periodical inspection to measure the thickness of the shell plates. Accordingly, the corrosion of the steel shell plates can be recognized by the change of the plate thickness. (I.S.)

  12. A container

    DEFF Research Database (Denmark)

    2012-01-01

    A container assembly for the containment of fluids or solids under a pressure different from the ambient pressure comprising a container (2) comprising an opening and an annular sealing, a lid (3) comprising a central portion (5) and engagement means (7) for engaging the annular flange, and sealing...... means (10) wherein the engagement means (7) is adapted, via the sealing means, to seal the opening when the pressure of the container assembly differs from the ambient pressure in such a way that the central portion (5) flexes in the axial direction which leads to a radial tightening of the engagement...... means (7) to the container, wherein the container further comprises locking means (12) that can be positioned so that the central portion is hindered from flexing in at least one direction....

  13. Shielded container

    International Nuclear Information System (INIS)

    Fries, B.A.

    1978-01-01

    A shielded container for transportation of radioactive materials is disclosed in which leakage from the container is minimized due to constructional features including, inter alia, forming the container of a series of telescoping members having sliding fits between adjacent side walls and having at least two of the members including machine sealed lids and at least two of the elements including hand-tightenable caps

  14. Measurement of the heat transfer parameters in infiltrated binary beryllium beds. Comparison between the results with PEHTRA and SUPER-PEHTRA

    International Nuclear Information System (INIS)

    Donne, M. dalle; Piazza, G.; Scaffidi-Argentina, F.

    2000-01-01

    For the next generation fusion reactors with a ceramic breeder blanket the use, as a neutron multiplier, of either a binary bed of large (∼ 2 mm) and small (∼ 0.1-0.2 mm) beryllium pebbles or a single size bed made of 1 mm or 2 mm pebbles is foreseen. The heat transfer parameters of such a binary pebble bed, namely the thermal conductivity and the heat transfer coefficient to the containing wall, have been investigated previously in the experimental device PEHTRA available at FZK. The experiments allowed to measure the effect of the bed temperature and of constraint exerted by the containing walls. The constraint is defined by the bed interference, i.e. the difference in the radial expansion between bed and the constraining walls related to the bed thickness (Δl/l). However, with the PEHTRA experiments, it was only possible to achieve a Δl/l value of 0.1%. A new experimental rig (SUPER-PEHTRA) has been constructed at FZK, which allows to achieve Δl/l values of 0.3% and to measure the pressure of the expanding bed on the containing walls. First experiments with a binary bed have been performed. The present paper reports on further experiments with binary beds and the establishing of equations correlating the data obtained for the present binary beds and for the binary bed experiments described. (orig.)

  15. Review of acute cancer beds.

    LENUS (Irish Health Repository)

    Evans, D S

    2012-01-01

    A review of admissions to cancer services at University Hospital Galway (UHG) was undertaken to assess the appropriateness of hospital usage. All cancer specialty patients admitted from 26-28 May 2009 were reviewed (n = 82). Chi square tests, Exact tests, and One-way ANOVA were utilised to analyse key issues emerging from the data. Fifty (61%) were classified as emergencies. Twenty three (67%) occupied a designated cancer bed with 24 (30%) in outlying non-oncology wards. The mean length of stay was 29.3 days. Possible alternatives to admission were identified for 15 (19%) patients. There was no evidence of discharge planning for 50 (60%) admissions. There is considerable potential to make more appropriate utilisation of UHG for cancer patients, particularly in terms of reducing bed days and length of stay and the proportion of emergency cancer admissions, and further developing integrated systems of discharge planning.

  16. Designing a CR Test bed

    DEFF Research Database (Denmark)

    Cattoni, Andrea Fabio; Buthler, Jakob Lindbjerg; Tonelli, Oscar

    2014-01-01

    with their own set up, since the potential costs and efforts could not pay back in term of expected research results. Software Defined Radio solutions offer an easy way to communication researchers for the development of customized research test beds. While several hardware products are commercially available......, an overview on common research-oriented software products for SDR development, namely GNU Radio, Iris, and ASGARD, will be provided, including how to practically start the software development of simple applications. Finally, best practices and examples of all the software platforms will be provided, giving...... they are up and running in generating results. With this chapter we would like to provide a tutorial guide, based on direct experience, on how to enter in the world of test bed-based research, providing both insight on the issues encountered in every day development, and practical solutions. Finally...

  17. ALL THAT "PHRAG": BRINGING ENGINEERING, WETLAND ECOLOGY, ENVIRONMENTAL SCIENCE, AND LANDSCAPE ECOLOGY TO BEAR ON THE QUESTION OF COMMON REED IN GREAT LAKES COASTAL WETLANDS

    Science.gov (United States)

    Coastal wetlands are among the most fragmented and disturbed ecosystems and the Great Lakes are no exception. One possible result is the observed increase in the presence and dominance of invasive and other opportunistic plant species, such as the common reed (Phragmites australi...

  18. Modeling the Integrated Expansion of the Canadian and U.S. Power Sectors with the Regional Energy Deployment System (ReEDS)

    Energy Technology Data Exchange (ETDEWEB)

    Zinaman, Owen [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Ibanez, Eduardo [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Heimiller, Donna [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Eurek, Kelly [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Mai, Trieu [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2015-07-02

    This document describes the development effort for creating a robust representation of the combined capacity expansion of the U.S. and Canadian electric sectors within the NREL ReEDS model. Thereafter, it demonstrates the newly established capability through an illustrative sensitivity analysis. In conducting the sensitivity analysis, we describe the value of an integrated modeling approach.

  19. Pre-study - mobile briquetting plant for reed canary grass in inland Northern Sweden; Foerstudie - mobil briketteringsanlaeggning foer roerflen i norrlands inland

    Energy Technology Data Exchange (ETDEWEB)

    Paulrud, Susanne; Lundmark, Bo

    2009-07-01

    The aim of this preliminary study was to summarize existing information and to develop an outline plan for a mobile briquette plant based on the conditions and requirements of reed canary grass production on forestry land. The results of the study show that there is potential to build up small-scale briquette production from reed canary grass in the areas around Arvidsjaur, Lycksele and Malaa. Important conclusions from the study are that there are potential users for reed canary grass briquettes in all three areas studied, but that profitability for mobile briquette plants is dependent on the willingness of the users to pay well for the briquettes. These briquette plants would need a relatively high degree of automation for commercial operation to be profitable. The first plant should therefore be collocated with another business so that staff, machinery (e.g. loader) and storage space can be shared with other operations. One appropriate location would be to build up activities for a mobile reed canary grass briquette plant around Glommers Miljoeenergi's pellet plant in Glommerstraesk. Thus, the plant could be used as a demonstration mobile unit, with a stationary 'home production base'CO{sub 2} Glommerstraesk

  20. Retrieving aboveground biomass of wetland Phragmites australis (common reed) using a combination of airborne discrete-return LiDAR and hyperspectral data

    Science.gov (United States)

    Luo, Shezhou; Wang, Cheng; Xi, Xiaohuan; Pan, Feifei; Qian, Mingjie; Peng, Dailiang; Nie, Sheng; Qin, Haiming; Lin, Yi

    2017-06-01

    Wetland biomass is essential for monitoring the stability and productivity of wetland ecosystems. Conventional field methods to measure or estimate wetland biomass are accurate and reliable, but expensive, time consuming and labor intensive. This research explored the potential for estimating wetland reed biomass using a combination of airborne discrete-return Light Detection and Ranging (LiDAR) and hyperspectral data. To derive the optimal predictor variables of reed biomass, a range of LiDAR and hyperspectral metrics at different spatial scales were regressed against the field-observed biomasses. The results showed that the LiDAR-derived H_p99 (99th percentile of the LiDAR height) and hyperspectral-calculated modified soil-adjusted vegetation index (MSAVI) were the best metrics for estimating reed biomass using the single regression model. Although the LiDAR data yielded a higher estimation accuracy compared to the hyperspectral data, the combination of LiDAR and hyperspectral data produced a more accurate prediction model for reed biomass (R2 = 0.648, RMSE = 167.546 g/m2, RMSEr = 20.71%) than LiDAR data alone. Thus, combining LiDAR data with hyperspectral data has a great potential for improving the accuracy of aboveground biomass estimation.

  1. Implementasi Dan Evaluasi Kinerja Encoder-Decoder Reed Solomon Pada M-Ary Quadrature Amplitude Modulation (M-Qam Mengunakan Wireless Open-Access Research Platform (WARP

    Directory of Open Access Journals (Sweden)

    Nadya Noor Oktarini

    2015-12-01

    Full Text Available Teknik modulasi multilevel seperti M-ary Quadrature Amplitude Modulation (M-QAM memiliki kelemahan yaitu semakin tinggi level modulasi yang digunakan, maka semakin tinggi pula nilai BER yang dihasilkan. Hal ini menyebabkan kinerja sistem menjadi tidak maksimal karena sistem semakin tidak tahan terhadap noise.  Salah satu teknik error control coding yang digunakan untuk mendeteksi kesalahan sekaligus memperbaiki kesalahan yaitu kode Reed Solomon. Kelebihan dari kode Reed Solomon adalah sifatnya yang non-binary artinya data diolah dalam simbol sehingga kemampuan koreksi data lebih banyak. WARP merupakan salah satu jenis dari teknologi SDR yang bisa diprogram untuk membuat prototype sistem komunikasi nirkabel. Pengimplementasian encoder dan decoder reed solomon dengan menggunakan perangkat WARP bertujuan untuk membandingkan modulasi M-QAM dengan dan tanpa kode reed solomon, kemudian mengetahui kinerja code rate yang berbeda pada modulasi M-QAM, serta mengetahui pengaruh besarnya daya pancar dan jarak pada sistem komunikasi. Hasil implementasi terbaik terdapat pada sistem RS (15,9 yang mana dapat memperbaiki kesalahan di semua level modulasi karena memiliki kemampuan koreksi error ganda (t=3 dengan ukuran k yang sama. Dari hasil implementasi juga didapatkan kesimpulan bahwa nilai BER akan semakin besar terhadap bertambahnya jarak antar node untuk daya pancar tetap, ini menandakan jarak sangat mempengaruhi kualitas kinerja suatu sistem komunikasi.

  2. Loss of B cell identity correlates with loss of B cell-specific transcription factors in Hodgkin/Reed-Sternberg cells of classical Hodgkin lymphoma

    DEFF Research Database (Denmark)

    Hertel, Christina B; Zhou, Xiao-ge; Hamilton-Dutoit, Stephen J

    2002-01-01

    In classical Hodgkin lymphoma the malignant Hodgkin/Reed-Sternberg (HRS) cells characteristically constitute only a small minority of the tumour load. Their origin has been debated for decades, but on the basis of rearrangement and somatic hypermutations of their immunoglubulin (Ig) genes, HRS ce...

  3. THE BAUXITES AND JELAR - BEDS

    Directory of Open Access Journals (Sweden)

    Krešimir Sakač

    1993-12-01

    Full Text Available Minor bauxite deposits and occurrences were formed in technically disturbed environments in the middle part of the Adriatic geotectonic unit in Dinarides, contemporary with the clastic Jelar-beds in the Late Lutetian time. Uneven chemical composition of these Eocene bauxites, their sporadic occurrences in developed paleorelief as well as characteristic petrographic composition of the immediate overlying rocks point out at different genetical conditions (the paper is published in Croatian.

  4. Advances in fluidized bed technologies

    International Nuclear Information System (INIS)

    Mutanen, K.

    1992-01-01

    Atmospheric fluidized bed combustion (AFBC) has advanced into industrial cogeneration and utility-scale electric generation. During the 1980's AFBC became the dominant technology in the United States for power generation systems fired with solid fuels. Development of pressurized fluidized bed combustion/gasification (PFB/G) has grown rapidly from small bench-scale rigs to large pilot and demonstration plants. AFBC as large as 160 MWe in capacity are now in operation, while pressurized combustion systems generating 80 MWe have started up two years ago. The major driving forces behind development of fluidized bed technologies are all the time strictening emission control regulations, need for fuel flexibility, repowering of older power plants and need for higher efficiency in electricity generation. Independent power producers (IPP) and cogenerators were the first ones in the United States who accepted AFBC for wide commercial use. Their role will be dominant in the markets of the 1990's also. Developers of AFBC systems are working on designs that reduce investment costs, decrease emissions and offer even higher reliability and availability in utility-scale applications while developers of PFBC/G work on designs that increase plant efficiencies, allow modular construction, decrease emissions further and reduce the cost of generating power. This paper presents technological background, commercial status, boiler performance, emissions and future developments for both AFBC and PFBC/G systems

  5. Bed agglomeration characteristics of palm shell and corncob combustion in fluidized bed

    International Nuclear Information System (INIS)

    Chaivatamaset, Pawin; Sricharoon, Panchan; Tia, Suvit

    2011-01-01

    Bed particle agglomeration was studied experimentally in an atmospheric laboratory scale fluidized bed combustor using quartz sand as bed material. Palm shell and corncob were tested. The objectives of the study were (i) to describe the contributions of the biomass ash properties and the operating conditions on the bed agglomeration tendency in term of the bed defluidization time (t def ) and the extent of potassium accumulation in the bed (K/Bed) and (ii) to further elucidate the ash inorganic behaviors and the governing bed agglomeration mechanisms. Defluidization caused by the bed agglomeration was experienced in all experiments during combustion of these biomasses, as a consequence of the presence of potassium in biomass. The experimental results indicated that biomass ash characteristics were the significant influence on the bed agglomeration. The increasing bed temperature, bed particle size and static bed height and the decreasing fluidizing air velocity enhanced the bed agglomeration tendency. The SEM/EDS analyses on the agglomerates confirmed that the agglomeration was attributed to the formation of potassium silicate liquid enriched on the surface of quartz sand particles in conjunction with the high surface temperature of the burning biomass char particles. Thermodynamic examination based on the phase diagram analysis confirmed that the molten phase formation was responsible for the agglomeration. In this study, the high molten ash fraction resulting from the high potassium content in biomass promoted the agglomeration and thus defluidization. - Highlights: → Palm shell and corncob of Thailand are tested their bed agglomeration behaviors during fluidized bed combustion. → The increase of bed temperature, bed particle size and static bed height and the decrease of air velocity enhance bed agglomeration. → The formation of ash derived potassium silicate melts enriched on sand surface is the key process. → The collision between char and sand

  6. The characteristics of bed agglomeration during fluidized bed combustion of eucalyptus bark

    International Nuclear Information System (INIS)

    Chaivatamaset, Pawin; Tia, Suvit

    2015-01-01

    The bed agglomeration behaviors were investigated experimentally when eucalyptus bark was burning tested in a laboratory scale fluidized bed reactor. The focuses of this work were the influences of operating conditions and bed materials on the bed agglomeration tendency and the elucidation in the behaviors of fuel inorganic elements and the governing mode of the agglomeration. It was found that the defluidization caused by the bed agglomeration was clearly detectable from the decrease in measured bed pressure. The growth of bed particle and accumulation of agglomerates during combustion provided the partial to complete defluidization. The defluidization was promoted by the increase of bed temperature and bed particle size, and the decrease of fluidizing air velocity. The SEM-EDS analyses revealed that the bed agglomeration was mainly attributed to the formation of potassium silicate compounds as liquid phase during the combustion. This was initiated by the chemical reaction between the bed particle and the released ash constituents. In this study, the inorganic migration from fuel particle to bed particle was likely dominated by the condensation/reaction. The thermodynamic examination by ternary phase diagram analysis corroborated that the liquid phase formation of the ash derived materials controlled the agglomeration. The alumina sand prevented the bed agglomeration since it was inactive in the formation of viscous molten substances during combustion at the observed temperatures. - Highlights: • The behaviors of bed agglomeration were studied during the fluidized bed combustion of eucalyptus bark. • The increase in bed temperature and sand size, and the decrease of air velocity promoted bed defluidization. • The formation of molten potassium silicate compounds conduced to the bed agglomeration. • Condensation/reaction was the dominant inorganic migration mechanism from fuel particle to bed particle. • The alumina sand prevented effectively the bed

  7. Method and apparatus for a combination moving bed thermal treatment reactor and moving bed filter

    Energy Technology Data Exchange (ETDEWEB)

    Badger, Phillip C.; Dunn, Jr., Kenneth J.

    2015-09-01

    A moving bed gasification/thermal treatment reactor includes a geometry in which moving bed reactor particles serve as both a moving bed filter and a heat carrier to provide thermal energy for thermal treatment reactions, such that the moving bed filter and the heat carrier are one and the same to remove solid particulates or droplets generated by thermal treatment processes or injected into the moving bed filter from other sources.

  8. Numerical analysis of a heat-generating, truncated conical porous bed in a fluid-filled enclosure

    International Nuclear Information System (INIS)

    Chakravarty, Aranyak; Datta, Priyankan; Ghosh, Koushik; Sen, Swarnendu; Mukhopadhyay, Achintya

    2016-01-01

    Analysis of natural convection in enclosures containing heat generating porous medium has important applications related to geothermal, chemical, thermal and nuclear energy such as in-vessel cooling of debris beds in nuclear reactors, cooling of coal stockpiles etc. The objective of the present numerical study is to characterise the pattern of fluid flow and energy transfer during steady laminar natural convective flow in a cylindrical enclosure with a centrally placed heat generating porous bed. Flow through porous region is modelled using Darcy–Brinkmann–Forchheimer model and local thermal equilibrium is assumed for the porous region. Analysis is carried out for a wide range of Rayleigh number (Ra), Darcy number (Da) and thermal conductivity ratio, as well as for different bed geometries. It is observed that in addition to Ra and Da, the bed geometry also plays a very important role in determining flow field and temperature distribution within the enclosure. Interestingly, a significant change is observed in energy transfer mode from the porous bed corresponding to specific values of bed permeability and bed heat generation rate. This is characterised in terms of Ra and Da. Further, it is observed that this change in energy transfer mode is highly dependent on Ra. - Highlights: • Natural convection is analysed in an enclosure with a heat generating porous bed. • Effect of dimensionless parameters as well as bed geometry has been investigated. • Energy transfer mechanism from porous bed changes with dimensionless parameters. • Bed geometry significantly affects fluid flow and energy transfer in the enclosure.

  9. Major salt beds of the Palo Duro and Dalhart Basins, Texas

    International Nuclear Information System (INIS)

    1983-12-01

    Major salt beds are defined as salt intervals at least 75 feet thick that contain no interbeds greater than 10 feet thick and include no more than 15 percent non-salt interbeds. Maps based on the interpretation of geophysical logs from hundreds of oil and gas exploration wells reveal seven major salt beds in the Palo Duro Basin and one major salt bed in the Dalhart Basin. The most extensive major salt beds are in the central and northern Palo Duro Basin, in the Upper San Andres Formation and the Lower San Andres Formation Units 4 and 5. Of these, the major salt bed within the Lower San Andres Formation Unit 4 is the most widespread and generally the thickest. 7 references, 15 figures, 2 tables

  10. Using atomic layer deposited tungsten to increase thermal conductivity of a packed bed

    Energy Technology Data Exchange (ETDEWEB)

    Van Norman, Staci A.; Falconer, John L.; Weimer, Alan W., E-mail: alan.weimer@colorado.edu [Department of Chemical and Biological Engineering, University of Colorado, UCB 596, Boulder, Colorado 80309-0596 (United States); Tringe, Joseph W.; Sain, John D. [Lawrence Livermore National Laboratory, 7000 East Ave, Livermore, California 94550 (United States); Yang, Ronggui [Department of Mechanical Engineering, University of Colorado, UCB 427, Boulder, Colorado 80309-0427 (United States)

    2015-04-13

    This study investigated the effective thermal conductivity (k{sub eff}) of packed-beds that contained porous particles with nanoscale tungsten (W) films of different thicknesses formed by atomic layer deposition (ALD). A continuous film on the particles is vital towards increasing k{sub eff} of the packed beds. For example, the k{sub eff} of an alumina packed bed was increased by three times after an ∼8-nm continuous W film with 20 cycles of W ALD, whereas k{sub eff} was decreased on a polymer packed bed with discontinuous, evenly dispersed W-islands due to nanoparticle scattering of phonons. For catalysts, understanding the thermal properties of these packed beds is essential for developing thermally conductive supports as alternatives to structured supports.

  11. Synthesis and crystal structure of lithium beryllium deuteride Li2BeD4.

    Science.gov (United States)

    Bulychev, Boris M; Shpanchenko, Roman V; Antipov, Evgeny V; Sheptyakov, Denis V; Bushmeleva, Svetlana N; Balagurov, Anatoly M

    2004-10-04

    Single-phase ternary deuteride Li(2)BeD(4) was synthesized by a high-pressure high-temperature technique from LiD and BeD(2). The crystal structure of Li(2)BeD(4) was solved from X-ray and neutron powder diffraction data. The compound crystallizes in the monoclinic space group P2(1)/c with lattice parameters a = 7.06228(9) A, b = 8.3378(1) A, c = 8.3465(1) A, beta =93.577(1) degrees, and Z = 8. Its structure contains isolated BeD(4) tetrahedra and Li atoms that are located in the structure interstices. Li(2)BeD(4) does not undergo any structural phase transitions at temperatures down to 8 K.

  12. Reactor container

    International Nuclear Information System (INIS)

    Fukazawa, Masanori.

    1991-01-01

    A system for controlling combustible gases, it has been constituted at present such that the combustible gases are controlled by exhausting them to the wet well of a reactor container. In this system, however, there has been a problem, in a reactor container having plenums in addition to the wet well and the dry well, that the combustible gases in such plenums can not be controlled. In view of the above, in the present invention, suction ports or exhaust ports of the combustible gas control system are disposed to the wet well, the dry well and the plenums to control the combustible gases in the reactor container. Since this can control the combustible gases in the entire reactor container, the integrity of the reactor container can be ensured. (T.M.)

  13. Clinical evaluation of an automated turning bed.

    Science.gov (United States)

    Melland, H I; Langemo, D; Hanson, D; Olson, B; Hunter, S

    1999-01-01

    The purposes of this study were to assess client comfort and sleep quality, client physiologic response (skin and respiratory status), the effect on the need for caregiver assistance, and cost when using an automated turning bed. Nonexperimental, evaluative study. Twenty-four adult home or long-term care resident subjects who had a degenerative disease, spinal cord injury, stroke, cerebral palsy, or back surgery. Each subject agreed to use the automated turning bed for four weeks. Researchers completed a demographic survey and skin assessment, and assessed each subject for pressure ulcer risk and for the need of assistance of a care giver for turning before and after the four weeks of using the turning bed. Subjects rated the turning bed in terms of comfort and sleep quality. Subjects rated the turning bed as more comfortable than their own bed and expressed satisfaction at the pain relief attained when on the turning bed. While using the turning bed, there was a significant improvement in sleep quality. No skin breakdown or deterioration in respiratory status occurred. Fewer subjects required the assistance of a caregiver for turning when on the turning bed. This automated turning bed shows great promise in meeting a need for patients with limited mobility whether they are homebound or in a residential community. Future studies that further investigate use of the turning bed for postoperative back patients while still in the acute care setting are indicated. Replicative studies with a larger sample size are also indicated.

  14. Reactor containment

    International Nuclear Information System (INIS)

    Kawabe, Ryuhei; Yamaki, Rika.

    1990-01-01

    A water vessel is disposed and the gas phase portion of the water vessel is connected to a reactor container by a pipeline having a valve disposed at the midway thereof. A pipe in communication with external air is extended upwardly from the liquid phase portion to a considerable height so as to resist against the back pressure by a waterhead in the pipeline. Accordingly, when the pressure in the container is reduced to a negative level, air passes through the pipeline and uprises through the liquid phase portion in the water vessel in the form of bubbles and then flows into the reactor container. When the pressure inside of the reactor goes higher, since the liquid surface in the water vessel is forced down, water is pushed up into the pipeline. Since the waterhead pressure of a column of water in the pipeline and the pressure of the reactor container are well-balanced, gases in the reactor container are not leaked to the outside. Further, in a case if a great positive pressure is formed in the reactor container, the inner pressure overcomes the waterhead of the column of water, so that the gases containing radioactive aerosol uprise in the pipeline. Since water and the gases flow being in contact with each other, this can provide the effect of removing aerosol. (T.M.)

  15. Sharps container

    Science.gov (United States)

    Lee, Angelene M. (Inventor)

    1992-01-01

    This invention relates to a system for use in disposing of potentially hazardous items and more particularly a Sharps receptacle for used hypodermic needles and the like. A Sharps container is constructed from lightweight alodined nonmagnetic metal material with a cup member having an elongated tapered shape and length greater than its transverse dimensions. A magnet in the cup member provides for metal retention in the container. A nonmagnetic lid member has an opening and spring biased closure flap member. The flap member is constructed from stainless steel. A Velcro patch on the container permits selective attachment at desired locations.

  16. Method for immobilizing particulate materials in a packed bed

    Science.gov (United States)

    Even, Jr., William R.; Guthrie, Stephen E.; Raber, Thomas N.; Wally, Karl; Whinnery, LeRoy L.; Zifer, Thomas

    1999-01-01

    The present invention pertains generally to immobilizing particulate matter contained in a "packed" bed reactor so as to prevent powder migration, compaction, coalescence, or the like. More specifically, this invention relates to a technique for immobilizing particulate materials using a microporous foam-like polymer such that a) the particulate retains its essential chemical nature, b) the local movement of the particulate particles is not unduly restricted, c) bulk powder migration and is prevented, d) physical and chemical access to the particulate is unchanged over time, and e) very high particulate densities are achieved. The immobilized bed of the present invention comprises a vessel for holding particulate matter, inlet and an outlet ports or fittings, a loosely packed bed of particulate material contained within the vessel, and a three dimensional porous matrix for surrounding and confining the particles thereby fixing the movement of individual particle to a limited local position. The established matrix is composed of a series of cells or chambers comprising walls surrounding void space, each wall forming the wall of an adjacent cell; each wall containing many holes penetrating through the wall yielding an overall porous structure and allowing useful levels of gas transport.

  17. Decoding of DBEC-TBED Reed-Solomon codes. [Double-Byte-Error-Correcting, Triple-Byte-Error-Detecting

    Science.gov (United States)

    Deng, Robert H.; Costello, Daniel J., Jr.

    1987-01-01

    A problem in designing semiconductor memories is to provide some measure of error control without requiring excessive coding overhead or decoding time. In LSI and VLSI technology, memories are often organized on a multiple bit (or byte) per chip basis. For example, some 256 K bit DRAM's are organized in 32 K x 8 bit-bytes. Byte-oriented codes such as Reed-Solomon (RS) codes can provide efficient low overhead error control for such memories. However, the standard iterative algorithm for decoding RS codes is too slow for these applications. The paper presents a special decoding technique for double-byte-error-correcting, triple-byte-error-detecting RS codes which is capable of high-speed operation. This technique is designed to find the error locations and the error values directly from the syndrome without having to use the iterative algorithm to find the error locator polynomial.

  18. Energy crop cultivations of reed canary grass - An inferior breeding habitat for the skylark, a characteristic farmland bird species

    Energy Technology Data Exchange (ETDEWEB)

    Vepsaelaeinen, Ville [Finnish Museum of Natural History, P.O. Box 17, University of Helsinki, FI-00014 Helsinki (Finland)

    2010-07-15

    Here, I present the first comparison of the abundance of farmland birds in energy grass fields and in cereal-dominated conventionally cultivated fields (CCFs). I demonstrate that in boreal farmland, skylark (Alauda arvensis) densities were significantly lower in reed canary grass (RCG) (Phalaris arundinacea) fields than in CCFs. I found that during the early breeding season RCG fields and CCFs are equally good habitats, but over the ensuing couple of weeks RCG rapidly grows too tall and dense for field-nesting species. Consequently, RCG is an inferior habitat for skylark for laying replacement clutches (after failure of first nesting) or for a second clutch after one successful nesting. The results imply that if RCG cultivation is to be expanded, the establishment of large monocultures should be avoided in farmland landscapes; otherwise the novel habitat may affect detrimentally the seriously depleted skylark population, and probably also other field-nesting bird species with similar breeding habitats. (author)

  19. Evaluation of electromagnetic interference between electromagnet and permanent magnet of reed switch of SMART control rod driver mechanism

    International Nuclear Information System (INIS)

    Hur, H.; Kim, J. H.; Park, J. S.; Yoo, J. Y.; Kim, J. I.

    2002-01-01

    Integral reactors require a fine reactivity control CEDM since the nuclear heating is used during the startup. Although a linear pulse motor type had been chosen for the SMART CEDM, a ball screw type is being considered as an alternative. A ball screw type CEDM driven by a rotary step motor has an emergency insertion system using electromagnet and also has a permanent magnet for RSPT in the upper pressure housing above the electromagnet. So it is necessary to evaluate an electromagnetic interference for reed switches in the vicinity of the electromagnet. This paper describes the design parameters for effective operation and the optimum design point was determined by analyzing the trend of the EMI characteristics

  20. Chemical composition and methane yield of reed canary grass as influenced by harvesting time and harvest frequency

    DEFF Research Database (Denmark)

    Kandel, Tanka Prasad; Sutaryo, Sutaryo; Møller, Henrik Bjarne

    2013-01-01

    This study examined the influence of harvest time on biomass yield, dry matter partitioning, biochemical composition and biological methane potential of reed canary grass harvested twice a month in one-cut (OC) management. The regrowth of biomass harvested in summer was also harvested in autumn...... as a two-cut management with (TC-F) or without (TC-U) fertilization after summer harvest. The specific methane yields decreased significantly with crop maturity that ranged from 384 to 315 and from 412 to 283 NL (normal litre) (kg VS)-1 for leaf and stem, respectively. Approximately 45% more methane...... was produced by the TC-F management (5430 Nm3 ha-1) as by the OC management (3735 Nm3 ha-1). Specific methane yield was moderately correlated with the concentrations of fibre components in the biomass. Larger quantity of biogas produced at the beginning of the biogas assay from early harvested biomass...

  1. Arundo donax L. reed: new perspectives for pulping and bleaching. Part 4. Peroxide bleaching of organosolv pulps.

    Science.gov (United States)

    Shatalov, A A; Pereira, H

    2005-05-01

    A comparative study on TCF (totally chlorine-free) bleachability of organosolv pulps from the annual fibre crop Arundo donax L. (giant reed) was carried out using a simple three-stage peroxide bleaching sequence without oxygen pre-bleaching. ASAM (alkali-sulfite-anthraquinone-methanol), Organocell (alkali-anthraquinone-methanol) and ethanol-soda organosolv pulps were bleached and compared with kraft pulp, as a reference. The final brightness of 76-78% ISO was attained for all tested pulps. The chemical charge required to reach this level of brightness varied for different pulps (despite the equal initial content of the residual lignin) and directly related to starting brightness values. No direct correlation between brightness improvement and lignin removal during bleaching was found, indicating the influence of the specific pulp properties introduced by pulping process on bleaching chemistry. The general higher bleaching response of organosolv pulps from A. donax was noted in comparison with kraft.

  2. PERBANDINGAN BIT ERROR RATE KODE REED-SOLOMON DENGAN KODE BOSE-CHAUDHURI-HOCQUENGHEM MENGGUNAKAN MODULASI 32-FSK

    Directory of Open Access Journals (Sweden)

    Eva Yovita Dwi Utami

    2016-11-01

    Full Text Available Kode Reed-Solomon (RS dan kode Bose-Chaudhuri-Hocquenghem (BCH merupakan kode pengoreksi error yang termasuk dalam jenis kode blok siklis. Kode pengoreksi error diperlukan pada sistem komunikasi untuk memperkecil error pada informasi yang dikirimkan. Dalam makalah ini, disajikan hasil penelitian kinerja BER sistem komunikasi yang menggunakan kode RS, kode BCH, dan sistem yang tidak menggunakan kode RS dan kode BCH, menggunakan modulasi 32-FSK pada kanal Additive White Gaussian Noise (AWGN, Rayleigh dan Rician. Kemampuan memperkecil error diukur menggunakan nilai Bit Error Rate (BER yang dihasilkan. Hasil penelitian menunjukkan bahwa kode RS seiring dengan penambahan nilai SNR, menurunkan nilai BER yang lebih curam bila dibandingkan sistem dengan kode BCH. Sedangkan kode BCH memberikan keunggulan saat SNR bernilai kecil, memiliki BER lebih baik daripada sistem dengan kode RS.

  3. Advanced sorbent development progam; development of sorbents for moving-bed and fluidized-bed applications

    International Nuclear Information System (INIS)

    Ayala, R.E.; Venkataramani, V.S.

    1998-01-01

    a market plan for large-scale fabrication of sorbents were developed. As an optional task, long-term bench-scale tests of the best moving-bed sorbents were conducted. Starting from thermodynamic calculations, several metal oxides were identified for potential use as hot gas cleanup sorbents using constructed phase stability diagrams and laboratory screening of various mixed-metal oxide formulations. Modified zinc titanates and other proprietary metal oxide formulations were evaluated at the bench scale and many of them found to be acceptable for operation in the target desulfurization temperature range of 370 C (700 F) to 538 C (1000 F) and regeneration temperatures up to 760 C (1400 F). Further work is still needed to reduce the batch-to-batch repeatability in the fabrication of modified zinc titanates for larger scale applications. The information presented in this Volume 1 report contains the results of moving-bed sorbent develop-ment at General Electrics Corporate Research and Development (GE-CRD). A separate Volume 2 report contains the results of the subcontract on fluidized-bed sorbent development at the Institute of Gas Technology (IGT)

  4. Reactor container

    International Nuclear Information System (INIS)

    Kojima, Yoshihiro; Hosomi, Kenji; Otonari, Jun-ichiro.

    1997-01-01

    In the present invention, a catalyst for oxidizing hydrogen to be disposed in a reactor container upon rupture of pipelines of a reactor primary coolant system is prevented from deposition of water droplets formed from a reactor container spray to suppress elevation of hydrogen concentration in the reactor container. Namely, a catalytic combustion gas concentration control system comprises a catalyst for oxidizing hydrogen and a support thereof. In addition, there is also disposed a water droplet deposition-preventing means for preventing deposition of water droplets in a reactor pressure vessel on the catalyst. Then, the effect of the catalyst upon catalytic oxidation reaction of hydrogen can be kept high. The local elevation of hydrogen concentration can be prevented even upon occurrence of such a phenomenon that various kinds of mobile forces in the container such as dry well cooling system are lost. (I.S.)

  5. Phenotypic divergence among west European populations of Reed Bunting Emberiza schoeniclus: the effects of migratory and foraging behaviours.

    Directory of Open Access Journals (Sweden)

    Júlio M Neto

    Full Text Available Divergent selection and local adaptation are responsible for many phenotypic differences between populations, potentially leading to speciation through the evolution of reproductive barriers. Here we evaluated the morphometric divergence among west European populations of Reed Bunting in order to determine the extent of local adaptation relative to two important selection pressures often associated with speciation in birds: migration and diet. We show that, as expected by theory, migratory E. s. schoeniclus had longer and more pointed wings and a slightly smaller body mass than the resident subspecies, with the exception of E. s. lusitanica, which despite having rounder wings was the smallest of all subspecies. Tail length, however, did not vary according to the expectation (shorter tails in migrants probably because it is strongly correlated with wing length and might take longer to evolve. E. s. witherbyi, which feed on insects hiding inside reed stems during the winter, had a very thick, stubby bill. In contrast, northern populations, which feed on seeds, had thinner bills. Despite being much smaller, the southern E. s. lusitanica had a significantly thicker, longer bill than migratory E. s. schoeniclus, whereas birds from the UK population had significantly shorter, thinner bills. Geometric morphometric analyses revealed that the southern subspecies have a more convex culmen than E. s. schoeniclus, and E. s. lusitanica differs from the nominate subspecies in bill shape to a greater extent than in linear bill measurements, especially in males. Birds with a more convex culmen are thought to exert a greater strength at the bill tip, which is in agreement with their feeding technique. Overall, the three subspecies occurring in Western Europe differ in a variety of traits following the patterns predicted from their migratory and foraging behaviours, strongly suggesting that these birds have became locally adapted through natural selection.

  6. Anoxic environments and oil source bed genesis

    Energy Technology Data Exchange (ETDEWEB)

    Demaison, G J [Chevron Overseas Petroleum Inc., San Francisco, CA; Moore, G T

    1980-01-01

    The anoxic, aquatic, environment is a mass of water so depleted in oxygen that virtually all aerobic biological activity has ceased. Anoxic conditions occur where the demand for oxygen in the water column exceeds the supply. The specific cause for preferential lipid enrichment probably relates to the biochemistry of anaerobic bacterial activity. Recent evidence suggests that ancient organic-rich sediments containing hydrogen-rich kerogens (potential oil source beds) were deposited in similar anoxic environments. We propose the following classification for modern aquatic anoxic settings: (1) Large anoxic lakes - Permanent stratification promotes development of anoxic bottom water, particularly in large, deep lakes, which are not subject to seasonal overturn, e.g., Lake Tanganyika. (2) Anoxic silled basins - Landlocked silled basins with positive water balance tend to become anoxic. Typical are the Baltic and Black Seas. In arid region seas (Red and Mediterranean Seas), evaporation exceeds river inflow, causing negative water balance and well-aerated, nutrient-depleted bottom waters. (3) Anoxic layers caused by upwelling - Develop only when the oxygen supply in deep water cannot match demand by decaying organisms. Examples are the Benguela current and Peru coastal upwelling. (4) Open ocean anoxic layers - Found at intermediate depths in the northeastern Pacific and northern Indian Oceans; due to distance from deep, oxygenated polar water sources. Analogous to world-wide anoxic events at times of global climatic warm-ups and major transgressions, as in late Jurassic and middle Cretaceous time. Petroleum exploration can be greatly assisted by using geochemistry to identify paleo-anoxic events in the stratigraphic record. Recognition of the proposed anoxic models in ancient sedimentary basins should help in regional mapping of oil shales and oil-source beds. 17 figures.

  7. The Safety of Hospital Beds: Ingress, Egress, and In-Bed Mobility.

    Science.gov (United States)

    Morse, Janice M; Gervais, Pierre; Pooler, Charlotte; Merryweather, Andrew; Doig, Alexa K; Bloswick, Donald

    2015-01-01

    To explore the safety of the standard and the low hospital bed, we report on a microanalysis of 15 patients' ability to ingress, move about the bed, and egress. The 15 participants were purposefully selected with various disabilities. Bed conditions were randomized with side rails up or down and one low bed with side rails down. We explored the patients' use of the side rails, bed height, ability to lift their legs onto the mattress, and ability to turn, egress, and walk back to the chair. The standard bed was too high for some participants, both for ingress and egress. Side rails were used by most participants when entering, turning in bed, and exiting. We recommend that side rails be reconsidered as a means to facilitate in-bed movement, ingress, and egress. Furthermore, single deck height settings for all patients are not optimal. Low beds as a safety measure must be re-evaluated.

  8. Design of fluidized-bed, biological denitrification systems

    International Nuclear Information System (INIS)

    Patton, B.D.; Hancher, C.W.; Pitt, W.W.; Walker, J.F.

    1982-01-01

    Many commercial processes yield nitrate-containing wastewaters that are being discharged to the environment because traditional recovery or disposal methods are economically unacceptable. The anticipated discharge limits (i.e., 10 to 20 g (NO 3 - )/m 3 ) being considered by many states will not allow continued release of these wastewaters. The new discharge standards can be met economically by use of the fluidizied-bed, biological denitrification process. Research and development studies were conducted with 0.05-, 0.10-, 0.20-, and 0.50-m-diam fluidized-bed bioreactor systems. Feed nitrate concentrations were in the 0 to 10,000 g (NO 3 - )/m 3 range. Using the data from these studies, rate expressions were developed for the destruction of nitrate as a function of nitrate concentration. Methods were also developed for sizing bioreactors and biomass control systems. The sizing methods for fluidized-bed denitrification systems are described, and support systems such as sampling and analysis, instrumentation and controls, utilities, and bacteria storage are discussed. Operation of the process is also briefly discussed to aid the designer. Using the methods presented in this report, fluidized-bed, biological denitrification systems can be designed to treat nitrate wastewater streams

  9. Application of debris-bed dryout data to CONACS-1 modeling

    International Nuclear Information System (INIS)

    Gabor, J.D.; Cassulo, J.C.; Pedersen, D.R.

    1982-01-01

    CONACS-1 (the first version of the DOE Containment Analysis Code System) which is currently under development requires extension of existing debris-bed dryout data to the wide range of conditions possible in an accident sequence. While there has been much effort on modeling of debris-bed dryout from first principles, there is no definitive model for beds of irregularly shaped particles of wide size distribution and for beds of varying heights. Existing debris-bed heat-transfer data with real materials are for the most part limited to dryout as a function of bed depth for adiabatic conditions of atmospheric pressure. These data must be extrapolated with the use of appropriate theoretical models based on experimentation with simulant materials to the ocnditions under consideration in the containment analysis. The data base selected for CONACS-1 is from measurements of dryout for beds of 100 to 1000 μm UO 2 with the sodium phase Joule heated. This particle size range which is typical for debris from fuel-coolant interactions is the most reasonable to use

  10. Thermal-hydraulic analysis techniques for axisymmetric pebble bed nuclear reactor cores

    International Nuclear Information System (INIS)

    Stroh, K.R.

    1979-03-01

    The pebble bed reactor's cylindrical core volume contains a random bed of small, spherical fuel-moderator elements. These graphite spheres, containing a central region of dispersed coated-particle fissile and fertile material, are cooled by high pressure helium flowing through the connected interstitial voids. A mathematical model and numerical solution technique have been developed which allow calculation of macroscopic values of thermal-hydraulic variables in an axisymmetric pebble bed nuclear reactor core. The computer program PEBBLE is based on a mathematical model which treats the bed macroscopically as a generating, conducting porous medium. The steady-state model uses a nonlinear Forchheimer-type relation between the coolant pressure gradient and mass flux, with newly derived coefficients for the linear and quadratic resistance terms. The remaining equations in the model make use of mass continuity, and thermal energy balances for the solid and fluid phases

  11. [Special beds. Pulmonary therapy system].

    Science.gov (United States)

    Calixto Rodríguez, Joaquín; Rodríguez Martínez, Xavier; Marín i Vivó, Gemma; Paunellas Albert, Josep

    2008-10-01

    To be bedridden reduces one's capacity to move and produces muscular debility that affects the respiratory system leading to a decreased effectiveness in expectoration, the ability to spit up sputum. The pulmonary therapy system integrated in a bed is the result of applying motorized elements to the articulation points of the bad in order to achieve safe positions at therapeutic angles, which improve the breathing-perfusion (blood flow) relationship. This system also makes it possible to apply vibration waves to the patient which favor the elimination of bronchial-pulmonary secretions, the rehabilitation of the bedridden patient and decrease the work load for nursing personnel.

  12. Particle bed reactor scaling relationships

    Science.gov (United States)

    Slovik, G.; Araj, K.; Horn, F. L.; Ludewig, H.; Benenati, R.

    The Particle Bed Reactor (PBR) concept can be used in several applications both as part of a power generating system or as a direct propulsion unit. In order to carry out optimization studies of systems involving a PBR, it is necessary to know the variation of the critical mass with pertinent system parameters such as weight, size, power level and thrust level. A parametric study is presented for all the practical combinations of fuel and moderating material. The PBR is described, the practical combinations of materials and dimensions are discussed, and an example is presented.

  13. An experimental simulation study of debris quenching in a radially stratified porous bed

    International Nuclear Information System (INIS)

    Sehgal, B.R.; Nayak, A.K.; Stepanyan, A.

    2004-01-01

    During a severe accident condition in a nuclear power plant, the core melt can fail the reactor vessel and relocate into the containment basement. In some accident management schemes, the vessel cavity is flooded with water. For these a particulate debris bed is likely to form on the cavity floor due to melt break-up in water. . In this situation, the coolability of debris bed on the containment floor is a crucial issue. This is because the debris bed still generates the decay heat and if it is uncoolable, it can eventually remelt and react with concrete basement generating a lot of noncondensable gases and pressurising the containment. Hence, it is important to cool the debris bed as an accident management programme. The main parameters affecting the coolability of the debris bed are its porosity which is a function of the size and shape of the particles which constitute the debris bed, the operating condition such as water flooding from the top or bottom of debris bed, water temperature and non-condensable gas generated during bed-concrete interactions. It is found from previous studies that the debris bed has a non-uniform particle distribution or a porosity stratification. This can happen both in radial and axial plane. For example, the bed can have a lower porosity at the centre and higher porosity at the periphery. It is of interest to investigate the quenching phenomena in such configurations so as to find an effective means of quenching the heat generating bed. While most of the previous investigations mainly concentrate on quenching of a homogenous or axially stratified particulate bed with volumetric heat generation, there are almost no studies on the above phenomena in a radially stratified porous bed. So the objective of this paper is to investigate the quenching phenomena in a radially stratified bed. To simulate the phenomena, we conducted experiments in an experimental facility named as POMECO (POrous MEdia COolability). The facility has a square

  14. Ladinian skonca beds of the Idrija Ore Deposit (W Slovenia

    Directory of Open Access Journals (Sweden)

    Jože Čar

    2013-12-01

    Full Text Available The richly mineralised Skonca beds (der Lagerschiefer were the most important mining level of the Idrija ore deposit. In addition to epigenetic ores, exceptional quantities of various rich syngenetic cinnabar ores could be found in these layers. »Jeklenka« (steel ore, »opekovka« (brick ore, »jetrenka« (liver ore, coral ore, and some other bedded cinnabar ores contained up to as much as 78 % Hg. These ores were excavated more or less intensively from their discovery in 1508 until the cessation of works in the Idrija Mine in 1977. The Skonca beds can be found in all parts of the Idrija ore deposit in the form of large or small, irregular, lenseshaped bodies or layers. In the section of the ore deposit known as šTalnina’, the Skonca beds are on average only 4 m thick, and from 10 to maximally 25 m in other parts of the ore deposit. The greatest thickness of these beds, i.e. around 40 m, can be found in the area of the Karóli tectonic unit, situated in the deepest part of the former Idrija Middle Triassic tectonic fault trough. The rocks in the Skonca beds are grouped in typical sequences, which represent a key for the reconstruction of sedimentary environments. The sequences are designated with the letters A, B, C and D. Sequence C is further divided into subsequences C1 with a carbonate and C2 with a siliceous structure. The lithological units of sequence A usually represent the lowest part of the Skonca beds, and may be the lateral equivalents of rocks of series B and subsequence C1. Sequence A is comprised of dispersed, gravelly varieties of carbonatic lythic sandstone, limestone and dolomite siltstone, as well as intercalations of gravelly silty micritic limestone and micritic limestone. Sequence B consists of typical transitional rocks between sequences A and C1, among which silty limestone with transitions to calcitic marlstone and claystone can be found. Sequence C is formed of šclassic’ Skonca rock beds. Although the bottom

  15. Fluid-bed process for SYNROC production

    International Nuclear Information System (INIS)

    Ackerman, F.J.; Grens, J.Z.; Ryerson, F.J.; Hoenig, C.L.; Bazan, F.; Peters, P.E.; Smith, R.; Campbell, J.H.

    1983-01-01

    SYNROC is a titanate-based ceramic waste developed for the immobilization of high-level nuclear reactor waste. Lawrence Livermore National Laboratory (LLNL) has investigated a fluid-bed technique for the large-scale production of SYNROC precursor powders. Making SYNROC in a fluid bed permits slurry drying, calcination and reduction-oxidation reactions to be carried out in a single unit. We present the results of SYNROC fluid-bed studies from two fluid-bed units 10 cm in diameter: an internally heated fluid-bed unit developed by Exxon Idaho and an externally heated unit constructed at LLNL. Bed operation over a range of temperatures, feed rates, fluidizing rates, and redox conditions indicate that SYNROC powders of a high density and a uniform particle size can be produced. These powders facilitate the densification step and yield dense ceramics (greater than 95% theoretical density) with well-developed phases and low leaching rates

  16. On partial fluidization in rotating fluidized beds

    International Nuclear Information System (INIS)

    Kao, J.; Pfeffer, R.; Tardos, G.I.

    1987-01-01

    In a rotating fluidized bed, unlike in a conventional fluidized bed, the granules are fluidized layer by layer from the (inner) free surface outward at increasing radius as the gas velocity is increased. This is a very significant and interesting phenomenon and is extremely important in the design of these fluidized beds. The phenomenon was first suggested in a theoretical analysis and recently verified experimentally in the authors' laboratory. However, in the first paper, the equations presented are too cumbersome and the influence of bed thickness is not clearly stated. In this note the authors present simplified equations, based on that paper, for the pressure drop and the minimum fluidizing velocities in a rotating fluidized bed. Experimental data are also shown and compared with the theoretical model, and the effect of bed thickness is shown. Furthermore, an explanation for the observation of a maximum in the pressure drop vs. velocity curve instead of the plateau derived by Chen is proposed

  17. Dale Reed with X-38 and a Subscale Model Used in Test Program

    Science.gov (United States)

    1997-01-01

    Dale Reed, a NASA engineer who worked on the original lifting-body research programs in the 1960s and 1970s, stands with a scale-model X-38 that was used in 1995 research flights, with a full-scale X-38 (80 percent of the size of a potential Crew Return Vehicle) behind him. The X-38 Crew Return Vehicle (CRV) research project is designed to develop the technology for a prototype emergency crew return vehicle, or lifeboat, for the International Space Station. The project is also intended to develop a crew return vehicle design that could be modified for other uses, such as a joint U.S. and international human spacecraft that could be launched on the French Ariane-5 Booster. The X-38 project is using available technology and off-the-shelf equipment to significantly decrease development costs. Original estimates to develop a capsule-type crew return vehicle were estimated at more than $2 billion. X-38 project officials have estimated that development costs for the X-38 concept will be approximately one quarter of the original estimate. Off-the-shelf technology is not necessarily 'old' technology. Many of the technologies being used in the X-38 project have never before been applied to a human-flight spacecraft. For example, the X-38 flight computer is commercial equipment currently used in aircraft and the flight software operating system is a commercial system already in use in many aerospace applications. The video equipment for the X-38 is existing equipment, some of which has already flown on the space shuttle for previous NASA experiments. The X-38's primary navigational equipment, the Inertial Navigation System/Global Positioning System, is a unit already in use on Navy fighters. The X-38 electromechanical actuators come from previous joint NASA, U.S. Air Force, and U.S. Navy research and development projects. Finally, an existing special coating developed by NASA will be used on the X-38 thermal tiles to make them more durable than those used on the space

  18. Gas distributor for fluidized bed coal gasifier

    Science.gov (United States)

    Worley, Arthur C.; Zboray, James A.

    1980-01-01

    A gas distributor for distributing high temperature reaction gases to a fluidized bed of coal particles in a coal gasification process. The distributor includes a pipe with a refractory reinforced lining and a plurality of openings in the lining through which gas is fed into the bed. These feed openings have an expanding tapered shape in the downstream or exhaust direction which aids in reducing the velocity of the gas jets as they enter the bed.

  19. Fluidized Bed Reactor as Solid State Fermenter

    Directory of Open Access Journals (Sweden)

    Krishnaiah, K.

    2005-01-01

    Full Text Available Various reactors such as tray, packed bed, rotating drum can be used for solid-state fermentation. In this paper the possibility of fluidized bed reactor as solid-state fermenter is considered. The design parameters, which affect the performances are identified and discussed. This information, in general can be used in the design and the development of an efficient fluidized bed solid-state fermenter. However, the objective here is to develop fluidized bed solid-state fermenter for palm kernel cake conversion into enriched animal and poultry feed.

  20. Investigation of Adsorbed Gases Content in Coal Beds in Bosnia and Herzegovina

    Directory of Open Access Journals (Sweden)

    Sadadinovic, J.

    2008-09-01

    Full Text Available Investigation of the gas fraction in coal beds in Bosnia & Herzegovina has been performed systematically since 1988. Gas in coal beds can be present in free or adsorbed form, and dissolved in water. Methods of investigation are based on the direct approach, according to which the gas fraction is determined in the undisturbed coal bed.The quantity of the adsorbed and free gas in the coal bed is directly proportional to the gas pressure. Dependence is hyperbolic. The quantity of the free gas in mining conditions is being determined by measurement of the desorption index (Δp2. The desorption index for the Srednjobosanski coal basin ranges to 1571 Pa, and the free gas pressure in this coal basin amounts up to 3.75 MPa. The desorption index for coal beds in “Kreka” and “Banoviće” coal basins has negative values, which means that the free gas fraction within the coal beds is negligible, while separation of adsorbed gases is diffuse. The free gas pressure in the mentioned coal basins is below 0.1 MPa. Adsorbed gases within the coal are connected by physical adsorption according to Langmuir’s isothermal adsorption curve. Langmuir’s quantities, for coal bed conditions, ranges as follows: am from 0.826 to 9.52 m3 t–1 pcs, and b from 6.65 10–3 to 0.247 MPa–1. Adsorbed gas within Miocene coal beds contains methane in amounts of 1.49 m3 t–1 čus CH4 andcarbon(IVoxide in amounts of 0.15 m3 t–1 čus CO2. Adsorbed gas within Pliocene coal beds, without methane, dominant is content of carbon(IVoxide.The investigation of the gas content in coal beds of BiH conducted in this article reveal that the coal beds primarily contain methane, while others hydrocarbons such as ethane, ethene, propane, propene and butane are present sporadically in fraction below φ/10–6. Based on the investigation results conducted in this article, simple mathematical forms were obtained for quick calculation of the free gas quantity by measurement of the

  1. Fungi solubilisation of low rank coal: performances of stirred tank, fluidised bed and packed bed reactors

    CSIR Research Space (South Africa)

    Oboirien, BO

    2013-02-01

    Full Text Available Coal biosolubilisation was investigated in stirred tank reactor, fluidised bed and fixed bed bioreactors with a view to highlight the advantages and shortcomings of each of these reactor configurations. The stirred aerated bioreactor and fluidised...

  2. Visualization of bed material movement in a simulated fluidized bed heat exchanger by neutron radiography

    International Nuclear Information System (INIS)

    Umekawa, Hisashi; Ozawa, Mamoru; Takenaka, Nobuyuki; Matsubayashi, Masahito

    1999-01-01

    The bulk movement of fluidized bed material was visualized by neutron radiography by introducing tracers into the bed materials. The simulated fluidized bed consisted of aluminum plates, and the bed material was sand of 99.7% SiO 2 (mean diameter: 0.218 mm, density: 2555 kg/m 3 ). Both materials were almost transparent to neutrons. Then the sand was colored by the contamination of the sand coated by CdSO 4 . Tracer particles of about 2 mm diameter were made by the B 4 C, bonded by the vinyl resin. The tracer was about ten times as large as the particle of fluidized bed material, but the traceability was enough to observe the bed-material bulk movement owing to the large effective viscosity of the fluidized bed. The visualized images indicated that the bubbles and/or wakes were important mechanism of the behavior of the fluidized bed movement

  3. High-precision zircon U-Pb geochronology of astronomically dated volcanic ash beds from the Mediterranean Miocene

    NARCIS (Netherlands)

    Wotzlaw, Jörn Frederik; Hüsing, Silja K.; Hilgen, Frederik J.; Schaltegger, Urs

    2014-01-01

    Several orbitally tuned Miocene sedimentary sequences around the Mediterranean contain abundant intercalated volcanic ash beds. These sequences provide the rare opportunity to directly compare radioisotopic dating methods with independent and accurate deposition ages derived from astrochronology. We

  4. STUDY OF HYDRODYNAMICS IN FIXED BED OF COMPOSITE GRANULAR MATERIALS

    Directory of Open Access Journals (Sweden)

    Stelian Petrescu

    2010-12-01

    Full Text Available This study aims at the experimental determination of pressure drop and friction factor at gas flow through fixed beds of granular silica gel, alumina and activated carbon, and establishment of an equation containing a modified friction factor Fm to calculate pressure drop. In order to calculate the modified friction factor, an equation was suggested.The experimental values for pressure drop and friction factor were determined using spherical grains of silica gel, cylindrical grains of alumina and silica gel, alumina and activated carbon impregnated with calcium chloride. By means of the suggested equation, the values of pressure drop in fixed bed were calculated and compared with the experimental values. A good agreement between the predicted and experimental data is noticed.

  5. Reactor container

    International Nuclear Information System (INIS)

    Furukawa, Hideyasu; Oyamada, Osamu; Uozumi, Hiroto.

    1976-01-01

    Purpose: To provide a container for a reactor provided with a pressure suppressing chamber pool which can prevent bubble vibrating load, particularly negative pressure generated at the time of starting to release exhaust from a main steam escape-safety valve from being transmitted to a lower liner plate of the container. Constitution: This arrangement is characterized in that a safety valve exhaust pool for main steam escape, in which a pressure suppressing chamber pool is separated and intercepted from pool water in the pressure suppressing chamber pool, a safety valve exhaust pipe is open into said safety valve exhaust pool, and an isolator member, which isolates the bottom liner plate in the pressure suppressing chamber pool from the pool water, is disposed on the bottom of the safety valve exhaust pool. (Nakamura, S.)

  6. CONTAIN calculations

    International Nuclear Information System (INIS)

    Scholtyssek, W.

    1995-01-01

    In the first phase of a benchmark comparison, the CONTAIN code was used to calculate an assumed EPR accident 'medium-sized leak in the cold leg', especially for the first two days after initiation of the accident. The results for global characteristics compare well with those of FIPLOC, MELCOR and WAVCO calculations, if the same materials data are used as input. However, significant differences show up for local quantities such as flows through leakages. (orig.)

  7. Metabolic Resistance in Bed Bugs

    Directory of Open Access Journals (Sweden)

    Omprakash Mittapalli

    2011-03-01

    Full Text Available Blood-feeding insects have evolved resistance to various insecticides (organochlorines, pyrethroids, carbamates, etc. through gene mutations and increased metabolism. Bed bugs (Cimex lectularius are hematophagous ectoparasites that are poised to become one of the major pests in households throughout the United States. Currently, C. lectularius has attained a high global impact status due to its sudden and rampant resurgence. Resistance to pesticides is one factor implicated in this phenomenon. Although much emphasis has been placed on target sensitivity, little to no knowledge is available on the role of key metabolic players (e.g., cytochrome P450s and glutathione S-transferases towards pesticide resistance in C. lectularius. In this review, we discuss different modes of resistance (target sensitivity, penetration resistance, behavioral resistance, and metabolic resistance with more emphasis on metabolic resistance.

  8. Debridement and wound bed preparation.

    Science.gov (United States)

    Falabella, Anna F

    2006-01-01

    Debridement can play a vital role in wound bed preparation and the removal of barriers that impair wound healing. In accordance with the TIME principles, debridement can help remove nonviable tissue, control inflammation or infection, decrease excess moisture, and stimulate a nonadvancing wound edge. There are many types of debridement, each with a set of advantages and disadvantages that must be clearly understood by the healthcare team. Failure to use the correct debridement method for a given type of wound may lead to further delays in healing, increase patient suffering, and unnecessarily increase the cost of care. This review article discusses the various methods of debridement, describes currently available debriding agents, evaluates the clinical data regarding their efficacy and safety, and describes strategies for the management of problematic nonhealing wounds.

  9. Particle Bed Reactor engine technology

    Science.gov (United States)

    Sandler, S.; Feddersen, R.

    1992-03-01

    This paper discusses the Particle Bed Reactor (PBR) based propulsion system being developed under the Space Nuclear Thermal Propulsion (SNTP) program. A PBR engine is a light weight, compact propulsion system which offers significant improvement over current technology systems. Current performance goals are a system thrust of 75,000 pounds at an Isp of 1000 sec. A target thrust to weight ratio (T/W) of 30 has been established for an unshielded engine. The functionality of the PBR, its pertinent technology issues and the systems required to make up a propulsion system are described herein. Accomplishments to date which include hardware development and tests for the PBR engine are also discussed. This paper is intended to provide information on and describe the current state-of-the-art of PBR technology.

  10. Particle Bed Reactor engine technology

    International Nuclear Information System (INIS)

    Sandler, S.; Feddersen, R.

    1992-01-01

    This paper discusses the Particle Bed Reactor (PBR) based propulsion system being developed under the Space Nuclear Thermal Propulsion (SNTP) program. A PBR engine is a light weight, compact propulsion system which offers significant improvement over current technology systems. Current performance goals are a system thrust of 75,000 pounds at an Isp of 1000 sec. A target thrust to weight ratio (T/W) of 30 has been established for an unshielded engine. The functionality of the PBR, its pertinent technology issues and the systems required to make up a propulsion system are described herein. Accomplishments to date which include hardware development and tests for the PBR engine are also discussed. This paper is intended to provide information on and describe the current state-of-the-art of PBR technology. 4 refs

  11. Reactor container

    International Nuclear Information System (INIS)

    Kato, Masami; Nishio, Masahide.

    1987-01-01

    Purpose: To prevent the rupture of the dry well even when the melted reactor core drops into a reactor pedestal cavity. Constitution: In a reactor container in which a dry well disposed above the reactor pedestal cavity for containing the reactor pressure vessel and a torus type suppression chamber for containing pressure suppression water are connected with each other, the pedestal cavity and the suppression chamber are disposed such that the flow level of the pedestal cavity is lower than the level of the pressure suppression water. Further, a pressure suppression water introduction pipeway for introducing the pressure suppression water into the reactor pedestal cavity is disposed by way of an ON-OFF valve. In case if the melted reactor core should fall into the pedestal cavity, the ON-OFF valve for the pressure suppression water introduction pipeway is opened to introduce the pressure suppression water in the suppression chamber into the pedestal cavity to cool the melted reactor core. (Ikeda, J.)

  12. Plasma container

    International Nuclear Information System (INIS)

    Ebisawa, Katsuyuki.

    1985-01-01

    Purpose: To enable to easily detect that the thickness of material to be abraded is reduced to an allowable limit from the outerside of the plasma container even during usual operation in a plasma vessel for a thermonuclear device. Constitution: A labelled material is disposed to the inside or rear face of constituent members of a plasma container undergoing the irradiation of plasma particles. A limiter plate to be abraded in the plasma container is composed of an armour member and heat removing plate, in which the armour member is made of graphite and heat-removing plate is made of copper. If the armour member is continuously abraded under the effect of sputtering due to plasma particles, silicon nitride embedded so far in the graphite at last appears on the surface of the limiter plate to undergo the impact shocks of the plasma particles. Accordingly, abrasion of the limiter material can be detected by a detector comprising gas chromatography and it can easily be detected from the outside of the plasma content even during normal operation. (Horiuchi, T.)

  13. Reactor container

    International Nuclear Information System (INIS)

    Shibata, Satoru; Kawashima, Hiroaki

    1984-01-01

    Purpose: To optimize the temperature distribution of the reactor container so as to moderate the thermal stress distribution on the reactor wall of LMFBR type reactor. Constitution: A good heat conductor (made of Al or Cu) is appended on the outer side of the reactor container wall from below the liquid level to the lower face of a deck plate. Further, heat insulators are disposed to the outside of the good heat conductor. Furthermore, a gas-cooling duct is circumferentially disposed at the contact portion between the good heat conductor and the deck plate around the reactor container. This enables to flow the cold heat from the liquid metal rapidly through the good heat conductor to the cooling duct and allows to maintain the temperature distribution on the reactor wall substantially linear even with the abrupt temperature change in the liquid metal. Further, by appending the good heat conductor covered with inactive metals not only on the outer side but also on the inside of the reactor wall to introduce the heat near the liquid level to the upper portion and escape the same to the cooling layer below the roof slab, the effect can be improved further. (Ikeda, J.)

  14. Pulsed atmospheric fluidized bed combustion

    Energy Technology Data Exchange (ETDEWEB)

    1989-11-01

    In order to verify the technical feasibility of the MTCI Pulsed Atmospheric Fluidized Bed Combustor technology, a laboratory-scale system was designed, built and tested. Important aspects of the operational and performance parameters of the system were established experimentally. A considerable amount of the effort was invested in the initial task of constructing an AFBC that would represent a reasonable baseline against which the performance of the PAFBC could be compared. A summary comparison of the performance and emissions data from the MTCI 2 ft {times} 2 ft facility (AFBC and PAFBC modes) with those from conventional BFBC (taller freeboard and recycle operation) and circulating fluidized bed combustion (CFBC) units is given in Table ES-1. The comparison is for typical high-volatile bituminous coals and sorbents of average reactivity. The values indicated for BFBC and CFBC were based on published information. The AFBC unit that was designed to act as a baseline for the comparison was indeed representative of the larger units even at the smaller scale for which it was designed. The PAFBC mode exhibited superior performance in relation to the AFBC mode. The higher combustion efficiency translates into reduced coal consumption and lower system operating cost; the improvement in sulfur capture implies less sorbent requirement and waste generation and in turn lower operating cost; lower NO{sub x} and CO emissions mean ease of site permitting; and greater steam-generation rate translates into less heat exchange surface area and reduced capital cost. Also, the PAFBC performance generally surpasses those of conventional BFBC, is comparable to CFBC in combustion and NO{sub x} emissions, and is better than CFBC in sulfur capture and CO emissions even at the scaled-down size used for the experimental feasibility tests.

  15. Topgrass. A trial of the suitability of switchgrass and reed canary grass as biofuel crops under UK conditions. 4th interim report

    Energy Technology Data Exchange (ETDEWEB)

    Riche, A.B.

    2004-04-01

    This report summarises the results of the Topgrass project growing miscanthus, switchgrass and reed canary grass at nine UK sites and covers a one year period between the winter harvesting of the plots in 2002/3 and 2003/4. Details are given of the rainfall, air temperature and solar radiation; crop monitoring for pests, diseases and weeds; crop measurements; and a comparison of all sites. Appendices present individual site diaries and individual site operations and costs.

  16. Small scale combustion of reed canary grass - inventory and evaluation of available technology; Smaaskalig foerbraenning av roerflen - inventering och vaerdering av tillgaenglig teknik

    Energy Technology Data Exchange (ETDEWEB)

    Gustavsson, Lennart; Paulrud, Susanne

    2011-07-01

    The feasibility of commercially available boilers in the interval 50 kW to 1 MW for use with reed canary grass (RCG) as fuel has been preliminary evaluated. The capacity to handle the large ash volumes generated by RCG both in terms of ash withdrawal and combustion quality was used as the main criteria. Nine boilers and two burners were identified and classified in a three-step scale from verified functioning on RCG to possible functioning with some design changes

  17. Supporting local farming communities and crop production resilience to climate change through giant reed (Arundo donax L.) cultivation: An Italian case study.

    Science.gov (United States)

    Bonfante, A; Impagliazzo, A; Fiorentino, N; Langella, G; Mori, M; Fagnano, M

    2017-12-01

    Bioenergy crops are well known for their ability to reduce greenhouse gas emissions and increase the soil carbon stock. Although such crops are often held to be in competition with food crops and thus raise the question of current and future food security, at the same time mitigation measures are required to tackle climate change and sustain local farming communities and crop production. However, in some cases the actions envisaged for specific pedo-climatic conditions are not always economically sustainable by farmers. In this frame, energy crops with high environmental adaptability and yields, such as giant reed (Arundo donax L.), may represent an opportunity to improve farm incomes, making marginal areas not suitable for food production once again productive. In so doing, three of the 17 Sustainable Development Goals (SDGs) of the United Nations would be met, namely SDG 2 on food security and sustainable agriculture, SDG 7 on reliable, sustainable and modern energy, and SDG 13 on action to combat climate change and its impacts. In this work, the response of giant reed in the marginal areas of an agricultural district of southern Italy (Destra Sele) and expected farm incomes under climate change (2021-2050) are evaluated. The normalized water productivity index of giant reed was determined (WP; 30.1gm -2 ) by means of a SWAP agro-hydrological model, calibrated and validated on two years of a long-term field experiment. The model was used to estimate giant reed response (biomass yield) in marginal areas under climate change, and economic evaluation was performed to determine expected farm incomes (woodchips and chopped forage). The results show that woodchip production represents the most profitable option for farmers, yielding a gross margin 50% lower than ordinary high-input maize cultivation across the study area. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Bedømmelsesformer inden for AMU

    DEFF Research Database (Denmark)

    Helms, Niels Henrik; Løfgreen, Lars Bo

    Sigtet med denne rapport om bedømmelse i AMU-regi er dels at indsamle dokumentation fra praksiserfaringer baseret på udvalgte TUP-projekter, og dels at beskrive national og international forskning på bedømmelses- og evalueringsområdet. Denne indsamling og beskrivelse vil lægge op til en diskussio...

  19. Bed-levelling experiments with suspended load

    NARCIS (Netherlands)

    Talmon, A.M.; De Graaff, J.

    1991-01-01

    Bed-levelling experiments are conducted in a straight laboratory channel. The experiments involve a significant fraction of suspended sediment transport. The purpose of the experiments is to provide data for modelling of the direction of sediment transport on a transverse sloping alluvial river bed,

  20. Flue Gas Emissions from Fluidized Bed Combustion

    NARCIS (Netherlands)

    Bramer, E.A.; Valk, M.

    1995-01-01

    During the past decades fluidized bed coal combustion was developed as a technology for burning coal in an effective way meeting the standards for pollution control. During the earlier years of research on fluidized bed combustion, the potential for limiting the S02 emission by adding limestone to

  1. Multiphase flow in spout fluidized bed granulators

    NARCIS (Netherlands)

    Buijtenen, van M.S.

    2011-01-01

    Spout fluidized beds are frequently used for the production of granules or particles through granulation, which are widely applied, for example, in the production of detergents, pharmaceuticals, food and fertilizers (M¨orl et al. 2007). Spout fluidized beds have a number of advantageous properties,

  2. 1 The Effect of Camber Bed Drainage

    African Journals Online (AJOL)

    User

    The Effect of Camber Bed Drainage Landforms on Soil. Nutrient Distribution and Grain Yield of Maize on the Vertisols ... The Vertisols of the Accra Plains of Ghana are water logged after significant rainfall ... Excess application of 15-15-15 NPK and sulphate of ammonia fertilizers (150% .... beds, before planting and nutrient.

  3. Print a Bed Bug Card - (Single Cards)

    Science.gov (United States)

    Two sets of business-card-sized lists of tips for recognizing bed bugs and the signs of an infestation, including a photo of bed bugs to assist identification. One card is for general use around home or office, the other for travelers.

  4. FLUIDIZED BED STEAM REFORMER MONOLITH FORMATION

    International Nuclear Information System (INIS)

    Jantzen, C

    2006-01-01

    Fluidized Bed Steam Reforming (FBSR) is being considered as an alternative technology for the immobilization of a wide variety of aqueous high sodium containing radioactive wastes at various DOE facilities in the United States. The addition of clay, charcoal, and a catalyst as co-reactants converts aqueous Low Activity Wastes (LAW) to a granular or ''mineralized'' waste form while converting organic components to CO 2 and steam, and nitrate/nitrite components, if any, to N 2 . The waste form produced is a multiphase mineral assemblage of Na-Al-Si (NAS) feldspathoid minerals with cage-like structures that atomically bond radionuclides like Tc-99 and anions such as SO 4 , I, F, and Cl. The granular product has been shown to be as durable as LAW glass. Shallow land burial requires that the mineralized waste form be able to sustain the weight of soil overburden and potential intrusion by future generations. The strength requirement necessitates binding the granular product into a monolith. FBSR mineral products were formulated into a variety of monoliths including various cements, Ceramicrete, and hydroceramics. All but one of the nine monoliths tested met the 2 durability specification for Na and Re (simulant for Tc-99) when tested using the Product Consistency Test (PCT; ASTM C1285). Of the nine monoliths tested the cements produced with 80-87 wt% FBSR product, the Ceramicrete, and the hydroceramic produced with 83.3 wt% FBSR product, met the compressive strength and durability requirements for an LAW waste form

  5. Assisted phytoextraction of heavy metals: compost and Trichoderma effects on giant reed (Arundo donax L. uptake and soil N-cycle microflora

    Directory of Open Access Journals (Sweden)

    Nunzio Fiorentino

    2013-12-01

    Full Text Available Little information is available as to the real effectiveness of the phytoextraction remediation technique, since laboratory experiments are still the most common way in which this is measured. Given this, an experiment on a cadmium-polluted soil was carried out in open field conditions in Southern Italy with the aim of assessing the growth and the phytoextraction potential of giant reed (Arundo donax L. Compost fertilisation and Trichoderma harzianum A6 inoculations were used to verify the possibility of increasing the metal uptake of the crop. Biomass yield of giant reed in the first growth season (average 12.8 Mg ha–1 was not affected by the Cd concentration in the soil and this increased significantly with compost fertilisation (13.8 Mg ha–1. Both compost fertilisation and T. harzianum inoculation increased cadmium uptake and translocation in leaves. Nitrifying bacteria was shown to be a useful tool to biomonitor soil quality. These results proved the suitability of the giant reed for assisted-phytoremedation with the use of compost fertilisation and T. harzianum.

  6. Microplate-Based Evaluation of the Sugar Yield from Giant Reed, Giant Miscanthus and Switchgrass after Mild Chemical Pre-Treatments and Hydrolysis with Tailored Trichoderma Enzymatic Blends.

    Science.gov (United States)

    Cianchetta, Stefano; Bregoli, Luca; Galletti, Stefania

    2017-11-01

    Giant reed, miscanthus, and switchgrass are considered prominent lignocellulosic feedstocks to obtain fermentable sugars for biofuel production. The bioconversion into sugars requires a delignifying pre-treatment step followed by hydrolysis with cellulase and other accessory enzymes like xylanase, especially in the case of alkali pre-treatments, which retain the hemicellulose fraction. Blends richer in accessory enzymes than commercial mix can be obtained growing fungi on feedstock-based substrates, thus ten selected Trichoderma isolates, including the hypercellulolytic strain Trichoderma reesei Rut-C30, were grown on giant reed, miscanthus, or switchgrass-based substrates. The produced enzymes were used to saccharify the corresponding feedstocks, compared to a commercial enzymatic mix (6 FPU/g). Feedstocks were acid (H 2 SO 4 0.2-2%, w/v) or alkali (NaOH 0.02-0.2%, w/v) pre-treated. A microplate-based approach was chosen for most of the experimental steps due to the large number of samples. The highest bioconversion was generally obtained with Trichoderma harzianum Or4/99 enzymes (78, 89, and 94% final sugar yields at 48 h for giant reed, miscanthus, and switchgrass, respectively), with significant increases compared to the commercial mix, especially with alkaline pre-treatments. The differences in bioconversion yields were only partially caused by xylanases (maximum R 2  = 0.5), indicating a role for other accessory enzymes.

  7. Hydrothermal Conversion of Giant Reed to Furfural and Levulinic Acid: Optimization of the Process under Microwave Irradiation and Investigation of Distinctive Agronomic Parameters

    Directory of Open Access Journals (Sweden)

    Claudia Antonetti

    2015-11-01

    Full Text Available The hydrothermal conversion of giant reed (Arundo donax L. to furfural (FA and levulinic acid (LA was investigated in the presence of dilute hydrochloric acid. FA and LA yields were improved by univariate optimization of the main reaction parameters: concentration of the acid catalyst, solid/liquid ratio of the reaction mixture, hydrolysis temperature, and reaction time. The catalytic performances were investigated adopting the efficient microwave (MW irradiation, allowing significant energy and time savings. The best FA and LA yields were further confirmed using a traditionally heated autoclave reactor, giving very high results, when compared with the literature. Hydrolysis temperature and time were the main reaction variables to be carefully optimized: FA formation needed milder reaction conditions, while LA more severe ones. The effect of the crop management (e.g., harvest time on FA/LA production was discussed, revealing that harvest time was not a discriminating parameter for the further optimization of both FA and LA production, due to the very high productivity of the giant reed throughout the year. The promising results demonstrate that giant reed represents a very interesting candidate for a very high contemporary production of FA and LA of up to about 70% and 90% of the theoretical yields, respectively.

  8. Continuous austempering fluidized bed furnace. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Srinivasan, M.N. [Lamar Univ., Beaumont, TX (United States). Dept. of Mechanical Engineering

    1997-09-23

    The intended objective of this project was to show the benefits of using a fluidized bed furnace for austenitizing and austempering of steel castings in a continuous manner. The division of responsibilities was as follows: (1) design of the fluidized bed furnace--Kemp Development Corporation; (2) fabrication of the fluidized bed furnace--Quality Electric Steel, Inc.; (3) procedure for austempering of steel castings, analysis of the results after austempering--Texas A and M University (Texas Engineering Experiment Station). The Department of Energy provided funding to Texas A and M University and Kemp Development Corporation. The responsibility of Quality Electric Steel was to fabricate the fluidized bed, make test castings and perform austempering of the steel castings in the fluidized bed, at their own expense. The project goals had to be reviewed several times due to financial constraints and technical difficulties encountered during the course of the project. The modifications made and the associated events are listed in chronological order.

  9. Does Bedding Affect the Airway and Allergy?

    Directory of Open Access Journals (Sweden)

    RW Siebers

    2011-03-01

    Full Text Available Various cross-sectional and longitudinal studies have suggested that synthetic bedding is associated with asthma, allergic rhinitis and eczema while feather bedding seems to be protective. Synthetic bedding items have higher house dust mite allergen levels than feather bedding items. This is possibly the mechanism involved although fungal and bacterial proinflammatory compounds and volatile organic compounds may play a role. In this review we present and discuss the epidemiological evidence and suggest possible mechanisms. Primary intervention studies are required to show whether feather bedding is protective for the development of childhood asthma and allergic diseases while secondary intervention studies are required to potentially reduce symptoms and medication use in subjects with established disease.

  10. Does bedding affect the airway and allergy?

    Science.gov (United States)

    Siebers, R W; Crane, J

    2011-04-01

    Various cross-sectional and longitudinal studies have suggested that synthetic bedding is associated with asthma, allergic rhinitis and eczema while feather bedding seems to be protective. Synthetic bedding items have higher house dust mite allergen levels than feather bedding items. This is possibly the mechanism involved although fungal and bacterial proinflammatory compounds and volatile organic compounds may play a role. In this review we present and discuss the epidemiological evidence and suggest possible mechanisms. Primary intervention studies are required to show whether feather bedding is protective for the development of childhood asthma and allergic diseases while secondary intervention studies are required to potentially reduce symptoms and medication use in subjects with established disease.

  11. CONTAIN calculations; CONTAIN-Rechnungen

    Energy Technology Data Exchange (ETDEWEB)

    Scholtyssek, W.

    1995-08-01

    In the first phase of a benchmark comparison, the CONTAIN code was used to calculate an assumed EPR accident `medium-sized leak in the cold leg`, especially for the first two days after initiation of the accident. The results for global characteristics compare well with those of FIPLOC, MELCOR and WAVCO calculations, if the same materials data are used as input. However, significant differences show up for local quantities such as flows through leakages. (orig.)

  12. Reactor container

    International Nuclear Information System (INIS)

    Hidaka, Masataka; Hatamiya, Shigeo; Kawasaki, Terufumi; Fukui, Toru; Suzuki, Hiroaki; Kataoka, Yoshiyuki; Kawabe, Ryuhei; Murase, Michio; Naito, Masanori.

    1990-01-01

    In order to suppress the pressure elevation in a reactor container due to high temperature and high pressure steams jetted out upon pipeway rupture accidents in the reactor container, the steams are introduced to a pressure suppression chamber for condensating them in stored coolants. However, the ability for suppressing the pressure elevation and steam coagulation are deteriorated due to the presence of inactive incondensible gases. Then, there are disposed a vent channel for introducing the steams in a dry well to a pressure suppression chamber in the reactor pressure vessel, a closed space disposed at the position lower than a usual liquid level, a first channel having an inlet in the pressure suppression chamber and an exit in the closed space and a second means connected by way of a backflow checking means for preventing the flow directing to the closed space. The first paths are present by plurality, a portion of which constitutes a syphon. The incondensible gases and the steams are discharged to the dry well at high pressure by using the difference of the water head for a long cooling time after the pipeway rupture accident. Then, safety can be improved without using dynamic equipments as driving source. (N.H.)

  13. Bed care for patients in palliative settings: considering risks to caregivers and bed surfaces.

    Science.gov (United States)

    Fragala, Guy

    2015-02-01

    Ensuring patients are comfortable in bed is key to effective palliative care, but when moving and positioning patients in bed, health professionals face an occupational risk of injury. The turning and positioning (TAP) system is a new method of moving patients in bed, that evidence has shown to reduce the risk of injury to caregivers. Providing the correct bed surface is another aspect of bed care essential to the comfort of the palliative patient, and to aid wound prevention and treatment. It is important to take a patient-centred approach when considering the most appropriate bed surface patients. This article provides an overview and discussion of these two aspects of bed care for palliative patients.

  14. Mechanisms of formation and destruction of nitrogen oxides during polyamide incineration in a fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Hahnel, F; Gadiou, R; Prado, G [Univ. de Haute Alsace, Mulhouse (France). Lab. de Gestion des Risques et Environnement

    1998-09-01

    In order to study the incineration of nitrogen-containing polymers, a fludized bed has been built. This paper reports the results for polyamide 6-6 incineration. The main nitrogen containing species have been identified, and the axial profiles of concentration of nitrogen oxides, HCN and NH3 have been measured. The main steps of decomposition of the polyamide were identified. We present an experimental investigation of the influence of operating parameters (temperature, excess air) on the formation and reduction of polymer combustion products. The yields of conversion of nitrogen to the different N-species have been calculated as a function of excess air in the fluidized bed. (orig.)

  15. Reactor container

    International Nuclear Information System (INIS)

    Oyamada, Osamu; Furukawa, Hideyasu; Uozumi, Hiroto.

    1979-01-01

    Purpose: To lower the position of an intermediate slab within a reactor container and fitting a heat insulating material to the inner wall of said intermediate slab, whereby a space for a control rod exchanging device and thermal stresses of the inner peripheral wall are lowered. Constitution: In the pedestal at the lower part of a reactor pressure vessel there is formed an intermediate slab at a position lower than diaphragm floor slab of the outer periphery of the pedestal thereby to secure a space for providing automatic exchanging device of a control rod driving device. Futhermore, a heat insulating material is fitted to the inner peripheral wall at the upper side of the intermediate slab part, and the temperature gradient in the wall thickness direction at the time of a piping rupture trouble is made gentle, and thermal stresses at the inner peripheral wall are lowered. (Sekiya, K.)

  16. Containment vessel

    International Nuclear Information System (INIS)

    Zbirohowski-Koscia, K.F.; Roberts, A.C.

    1980-01-01

    A concrete containment vessel for nuclear reactors is disclosed that is spherical and that has prestressing tendons disposed in first, second and third sets, the tendons of each set being all substantially concentric and centred around a respective one of the three orthogonal axes of the sphere; the tendons of the first set being anchored at each end at a first anchor rib running around a circumference of the vessel, the tendons of the second set being anchored at each end at a second anchor rib running around a circumference of the sphere and disposed at 90 0 to the first rib, and the tendons of the third set being anchored some to the first rib and the remainder to the second rib. (author)

  17. Experimental investigation on the changes in bed properties of a ...

    African Journals Online (AJOL)

    Experimental investigation on the changes in bed properties of a downdraft ... pressure measurements, physical observation, sampling of bed particles, bed agitation, etc. The generated producer gas was cleaned and cooled in downstream ...

  18. Posttreatment Feeding Affects Mortality of Bed Bugs (Hemiptera: Cimicidae) Exposed to Insecticides.

    Science.gov (United States)

    Singh, Narinderpal; Wang, Changlu; Cooper, Richard

    2016-02-01

    Insecticide sprays and dusts are used for controlling bed bugs, Cimex lectularius L. In natural environments, bed bugs have daily access to hosts after they are exposed to insecticides. The established laboratory insecticide bioassay protocols do not provide feeding after insecticide treatments, which can result in inflated mortality compared with what would be encountered in the field. We evaluated the effect of posttreatment feeding on mortality of bed bugs treated with different insecticides. None of the insecticides tested had a significant effect on the amount of blood consumed and percent feeding. The effect of posttreatment feeding on bed bug mortality varied among different insecticides. Feeding significantly reduced mortality in bed bugs exposed to deltamethrin spray, an essential oil mixture (Bed Bug Fix) spray, and diatomaceous earth dust. Feeding increased the mean survival time for bed bugs treated with chlorfenapyr spray and a spray containing an essential oil mixture (Ecoraider), but did not affect the final mortality. First instars hatched from eggs treated with chlorfenapyr liquid spray had reduced feeding compared with nymphs hatched from nontreated eggs. Those nymphs hatched from eggs treated with chlorfenapyr liquid spray and successfully fed had reduced mortality and a higher mean survival time than those without feeding. We conclude that the availability of a bloodmeal after insecticide exposure has a significant effect on bed bug mortality. Protocols for insecticide efficacy testing should consider offering a bloodmeal to the treated bed bugs within 1 to 3 d after treatment. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  19. The role of bed-parallel slip in the development of complex normal fault zones

    Science.gov (United States)

    Delogkos, Efstratios; Childs, Conrad; Manzocchi, Tom; Walsh, John J.; Pavlides, Spyros

    2017-04-01

    Normal faults exposed in Kardia lignite mine, Ptolemais Basin, NW Greece formed at the same time as bed-parallel slip-surfaces, so that while the normal faults grew they were intermittently offset by bed-parallel slip. Following offset by a bed-parallel slip-surface, further fault growth is accommodated by reactivation on one or both of the offset fault segments. Where one fault is reactivated the site of bed-parallel slip is a bypassed asperity. Where both faults are reactivated, they propagate past each other to form a volume between overlapping fault segments that displays many of the characteristics of relay zones, including elevated strains and transfer of displacement between segments. Unlike conventional relay zones, however, these structures contain either a repeated or a missing section of stratigraphy which has a thickness equal to the throw of the fault at the time of the bed-parallel slip event, and the displacement profiles along the relay-bounding fault segments have discrete steps at their intersections with bed-parallel slip-surfaces. With further increase in displacement, the overlapping fault segments connect to form a fault-bound lens. Conventional relay zones form during initial fault propagation, but with coeval bed-parallel slip, relay-like structures can form later in the growth of a fault. Geometrical restoration of cross-sections through selected faults shows that repeated bed-parallel slip events during fault growth can lead to complex internal fault zone structure that masks its origin. Bed-parallel slip, in this case, is attributed to flexural-slip arising from hanging-wall rollover associated with a basin-bounding fault outside the study area.

  20. Seasonal changes in metal accumulation and distribution in the organs of Phragmites australis (common reed from Lake Skadar, Montenegro

    Directory of Open Access Journals (Sweden)

    Kastratović Vlatko

    2013-01-01

    Full Text Available Due to its ability to accumulate metals, availability throughout the year and its large biomass, Phragmites australis (common reed is suitable for biomonitoring studies for the evaluation of load level of water ecosystem with trace metals. The heavy metals concentration in P.australis tissue can be several ten to several thousand times higher than those in the surrounding water. In this study we examined the content of heavy metals (Cd, Co, Cr, Cu, Mn, Ni, Pb, Zn, Sr and V in sediment, water and different organs of Phragmites australis collected from Lake Skadar, Montenegro, during different seasons of the year 2011. The highest concentrations of Sr were found in the leaves, while the other studied metals showed their highest concentrations in the roots. Thus, P. australis is considered a root bioaccumulation species. For most metals the concentration in roots and stems increases over time until the end of the growing season, and then decreases, while the concentration in leaves increases even after the growing season of the plant. If P. australis is used for phytoremediation purposes, then it should be harvested after the growing season because then the concentration of metals in the aboveground parts is maximal.

  1. The two-dimensional vibrating reed technique. A study of anisotropic pinning in high-temperature superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Karelina, Anna

    2004-02-18

    In this work the anisotropy of the pinning forces of vortices in a-b plane of high temperature-supraconductors was examined. For this purpose vibrating reed with two degrees of freedom of the oscillation was constructed. The pinning forces were examined in single crystals of YBa{sub 2}Cu{sub 3}O{sub 7} and Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub 8}. The experiments with YBa{sub 2}Cu{sub 3}O{sub 7} show that at temperatures lower than 78 K the vortices are in a nonequilibrium state. This leads to a flux creep and to a drift of the resonance frequency with time. This prevents the comparison of resonance curves in different directions of oscillations. In Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub 8} single crystals the vortices are in more stable state, but the measurements of the resonance curves in different directions show no indication of the four-fold symmetry. At temperatures below 60 K a strong hysteresis of the resonance frequency and the resonance-oscillation amplitude was found in YBa{sub 2}Cu{sub 3}O{sub 7} crystals as a function of the magnetic field. (orig.)

  2. Do females invest more into eggs when males sing more attractively? Postmating sexual selection strategies in a monogamous reed passerine.

    Science.gov (United States)

    Krištofík, Ján; Darolová, Alžbeta; Majtan, Juraj; Okuliarová, Monika; Zeman, Michal; Hoi, Herbert

    2014-04-01

    Maternal investment can play an important role for offspring fitness, especially in birds, as females have to provide their eggs with all the necessary nutrients for the development of the embryo. It is known that this type of maternal investment can be influenced by the quality of the male partner. In this study, we first verify that male song is important in the mate choice of female Eurasian reed warblers, as males mate faster when their singing is more complex. Furthermore, female egg investment varies in relation to male song characteristics. Interestingly, clutch size, egg weight, or size, which can be considered as an high-cost investment, is not influenced by male song characteristics, whereas comparably low-cost investment types like investment into diverse egg components are adjusted to male song characteristics. In line with this, our results suggest that female allocation rules depend on investment type as well as song characteristics. For example, egg white lysozyme is positively correlated with male song complexity. In contrast, a negative correlation exists between-song speed and syllable repetitiveness and egg yolk weight as well as egg yolk testosterone concentration. Thus, our results suggest that female egg investment is related to male song performance in several aspects, but female investment patterns regarding various egg compounds are not simply correlated.

  3. Primary Refractory and Relapsed Classical Hodgkin Lymphoma - Significance of Differential CD15 Expression in Hodgkin-Reed-Sternberg Cells

    Directory of Open Access Journals (Sweden)

    Daniel Benharroch, Shai Pilosof, Jacob Gopas, Itai Levi

    2012-01-01

    Full Text Available We recognized a few possible complications of classical Hodgkin lymphoma therapy in a cohort of 209 patients: 8 developed a primary refractory disease (primary progression, 36 showed an early relapse and 21 showed a late relapse. Sialyl-CD15 expression in Hodgkin-Reed-Sternberg cells was significantly more positive in primary refractory Hodgkin lymphoma, which confirms our previously published findings. Bcl-2 showed a significantly lower level of expression in primary refractory disease than in the other follow-up groups. This is in contrast with a previous finding of Bcl-2, associated with a poor prognosis in primary refractory illness. Another category of variables, old age and advanced stages, was significantly different in the various complications but this finding is probably to be expected. We could not demonstrate a difference between the sequels and the control group with regard to several clinical and immunohistochemical markers. Sialyl-CD15 and Bcl-2 expression, in contrast, were confirmed as prognostic factors, mainly of tumor progression into primary refractory disease.

  4. Reed canary grass observations of effects on crop stand and fibre quality caused by infestation of Epicalamus phalaridis

    Directory of Open Access Journals (Sweden)

    S. HELLQVIST

    2008-12-01

    Full Text Available A severe infestation of the gall midge Epicalamus phalaridis (Diptera: Cecidomyiidaeoccurred in a field of reed canary grass, Phalaris arundinacea in northern Sweden. The midge species has potential to become a serious pest on Phalaris grown for bioenergy or fibre production. Larvae of the midge feed beneath leaf sheaths and the crop lodges in late summer. Details are given on the biology of the midge. In the infested field, population densities of the midge were very high during three consecutive years. The crop was weakened and the occurrence of weeds increased. The dry matter yields declined markedly and were after three years of midge-attack about 50% of the average yield in the preceding years. The yield dropped comparatively more when the crop was harvested in the spring as opposed to harvest in late autumn and more at a nitrogen fertilisation at 100 kg compared to 200 kg N ha–1 per year. The effect of midge attack on fibre quality was studied. The fibre properties of midge-infested parts of internodes were poor, but as midge-damaged parts are brittle, they could probably be sorted out in a fractionation process. Undamaged parts of infested internodes had the same fibre properties as those from an uninfested crop.;

  5. DNA Superresolution Structure of Reed-Sternberg Cells Differs Between Long-Lasting Remission Versus Relapsing Hodgkin's Lymphoma Patients.

    Science.gov (United States)

    Righolt, Christiaan H; Knecht, Hans; Mai, Sabine

    2016-07-01

    Recent developments in microscopy have led to superresolution microscopy images of cells. Structured illumination microscopy was used before to reveal new details in the DNA structure and the structure of the DNA-free space in the DAPI-stained cell nuclei of the Hodgkin's lymphoma HDLM-2 cell line. This study extends this technology to primary pre-treatment classical Hodgkin's lymphoma samples of ten patients. Significant differences in both the DNA structure and the structure of the DNA-free space were detected between lymphocytes and malignant cells. Both types of structures were similar for lymphocytes of different patients. When the patients were un-blinded and grouped based on their clinical outcome, either non-relapsed or relapsed, a significant difference in the DNA structure of their Reed-Sternberg (RS) cells was found. Since, RS cells develop from mono-nucleated Hodgkin (H) cells, these data suggest distinct architectural restructuring of nuclei during RS cell formation in patients going to long-lasting remission versus relapse. J. Cell. Biochem. 117: 1633-1637, 2016. © 2015 Wiley Periodicals, Inc. © 2015 Wiley Periodicals, Inc.

  6. The weed species composition in a reed canary grass (Phalaris arundinacea L. plantation for energy purposes depending on its age

    Directory of Open Access Journals (Sweden)

    Tomasz R. Sekutowski

    2014-12-01

    Full Text Available The present experiment, carried out in nine production fields of reed canary grass (Phalaris arundinacea grown for energy purposes, evaluated the effect of plantation age on the occurrence and species composition of weeds. The selected plantations were divided into 3 groups that were conventionally called “young” (1–2 years old, “middle-aged” (3–5 years old, and “older” plantations (6–8 years old. Regardless of plantation age, altogether 43 species were found in the experimental fields. Moreover, 6 species were common for all the plantations and were found in them regardless of plantation age. The least species, only 18, were found on the “young” plantations, almost twice more on the “older” ones (30 species, whereas the largest spectrum of species was found in the “middle-aged” plantations (33 species. In the “young” plantations, annual weeds were the most common, with the highest constancy and coverage index found for Chenopodium album, Matricaria maritima ssp. inodora and Echinochloa crus-galli. The greatest variation in species was found in the “middle-aged” plantations. However, only 4 species achieved the highest constancy and coverage index: Matricaria maritima ssp. inodora, Cirsium arvense, Poa trivialis and Taraxacum officinale. Furthermore, perennial weeds were found to be dominant in the “older” plantations. Within this group, Poa trivialis, Taraxacum officinale, Urtica dioica, Plantago maior, and Cirsium arvense had the highest constancy and coverage index.

  7. Chemical composition and methane yield of reed canary grass as influenced by harvesting time and harvest frequency.

    Science.gov (United States)

    Kandel, Tanka P; Sutaryo, Sutaryo; Møller, Henrik B; Jørgensen, Uffe; Lærke, Poul E

    2013-02-01

    This study examined the influence of harvest time on biomass yield, dry matter partitioning, biochemical composition and biological methane potential of reed canary grass harvested twice a month in one-cut (OC) management. The regrowth of biomass harvested in summer was also harvested in autumn as a two-cut management with (TC-F) or without (TC-U) fertilization after summer harvest. The specific methane yields decreased significantly with crop maturity that ranged from 384 to 315 and from 412 to 283 NL (normal litre) (kgVS)(-1) for leaf and stem, respectively. Approximately 45% more methane was produced by the TC-F management (5430Nm(3)ha(-1)) as by the OC management (3735Nm(3)ha(-1)). Specific methane yield was moderately correlated with the concentrations of fibre components in the biomass. Larger quantity of biogas produced at the beginning of the biogas assay from early harvested biomass was to some extent off-set by lower concentration of methane. Copyright © 2012 Elsevier Ltd. All rights reserved.

  8. Coupling scales for modelling heavy metal vaporization from municipal solid waste incineration in a fluid bed by CFD

    Energy Technology Data Exchange (ETDEWEB)

    Soria, José, E-mail: jose.soria@probien.gob.ar [Institute for Research and Development in Process Engineering, Biotechnology and Alternative Energies (PROBIEN, CONICET – UNCo), 1400 Buenos Aires St., 8300 Neuquén (Argentina); Gauthier, Daniel; Flamant, Gilles [Processes, Materials and Solar Energy Laboratory (PROMES-CNRS, UPR 8521), 7 Four Solaire Street, Odeillo, 66120 Font-Romeu (France); Rodriguez, Rosa [Chemical Engineering Institute, National University of San Juan, 1109 Libertador (O) Avenue, 5400 San Juan (Argentina); Mazza, Germán [Institute for Research and Development in Process Engineering, Biotechnology and Alternative Energies (PROBIEN, CONICET – UNCo), 1400 Buenos Aires St., 8300 Neuquén (Argentina)

    2015-09-15

    Highlights: • A CFD two-scale model is formulated to simulate heavy metal vaporization from waste incineration in fluidized beds. • MSW particle is modelled with the macroscopic particle model. • Influence of bed dynamics on HM vaporization is included. • CFD predicted results agree well with experimental data reported in literature. • This approach may be helpful for fluidized bed reactor modelling purposes. - Abstract: Municipal Solid Waste Incineration (MSWI) in fluidized bed is a very interesting technology mainly due to high combustion efficiency, great flexibility for treating several types of waste fuels and reduction in pollutants emitted with the flue gas. However, there is a great concern with respect to the fate of heavy metals (HM) contained in MSW and their environmental impact. In this study, a coupled two-scale CFD model was developed for MSWI in a bubbling fluidized bed. It presents an original scheme that combines a single particle model and a global fluidized bed model in order to represent the HM vaporization during MSW combustion. Two of the most representative HM (Cd and Pb) with bed temperatures ranging between 923 and 1073 K have been considered. This new approach uses ANSYS FLUENT 14.0 as the modelling platform for the simulations along with a complete set of self-developed user-defined functions (UDFs). The simulation results are compared to the experimental data obtained previously by the research group in a lab-scale fluid bed incinerator. The comparison indicates that the proposed CFD model predicts well the evolution of the HM release for the bed temperatures analyzed. It shows that both bed temperature and bed dynamics have influence on the HM vaporization rate. It can be concluded that CFD is a rigorous tool that provides valuable information about HM vaporization and that the original two-scale simulation scheme adopted allows to better represent the actual particle behavior in a fluid bed incinerator.

  9. Coupling scales for modelling heavy metal vaporization from municipal solid waste incineration in a fluid bed by CFD

    International Nuclear Information System (INIS)

    Soria, José; Gauthier, Daniel; Flamant, Gilles; Rodriguez, Rosa; Mazza, Germán

    2015-01-01

    Highlights: • A CFD two-scale model is formulated to simulate heavy metal vaporization from waste incineration in fluidized beds. • MSW particle is modelled with the macroscopic particle model. • Influence of bed dynamics on HM vaporization is included. • CFD predicted results agree well with experimental data reported in literature. • This approach may be helpful for fluidized bed reactor modelling purposes. - Abstract: Municipal Solid Waste Incineration (MSWI) in fluidized bed is a very interesting technology mainly due to high combustion efficiency, great flexibility for treating several types of waste fuels and reduction in pollutants emitted with the flue gas. However, there is a great concern with respect to the fate of heavy metals (HM) contained in MSW and their environmental impact. In this study, a coupled two-scale CFD model was developed for MSWI in a bubbling fluidized bed. It presents an original scheme that combines a single particle model and a global fluidized bed model in order to represent the HM vaporization during MSW combustion. Two of the most representative HM (Cd and Pb) with bed temperatures ranging between 923 and 1073 K have been considered. This new approach uses ANSYS FLUENT 14.0 as the modelling platform for the simulations along with a complete set of self-developed user-defined functions (UDFs). The simulation results are compared to the experimental data obtained previously by the research group in a lab-scale fluid bed incinerator. The comparison indicates that the proposed CFD model predicts well the evolution of the HM release for the bed temperatures analyzed. It shows that both bed temperature and bed dynamics have influence on the HM vaporization rate. It can be concluded that CFD is a rigorous tool that provides valuable information about HM vaporization and that the original two-scale simulation scheme adopted allows to better represent the actual particle behavior in a fluid bed incinerator

  10. Associations of selected bedding types with incidence rates of subclinical and clinical mastitis in primiparous Holstein dairy cows.

    Science.gov (United States)

    Rowbotham, R F; Ruegg, P L

    2016-06-01

    The objective of this observational study was to determine the association of exposure to selected bedding types with incidence of subclinical (SM) and clinical mastitis (CM) in primiparous Holstein dairy cows housed in identical pens at a single facility. At parturition, primiparous cows were randomly assigned to pens containing freestalls with 1 of 4 bedding materials: (1) deep-bedded new sand (NES, n=27 cows), (2) deep-bedded recycled sand (RS, n=25 cows), (3) deep-bedded manure solids (DBMS, n=31 cows), and (4) shallow-bedded manure solids over foam-core mattresses (SBMS, n=26 cows). For 12mo, somatic cell counts of quarter milk samples were determined every 28d and duplicate quarter milk samples were collected for microbiological analysis from all quarters with SM (defined as somatic cell count >200,000 cells/mL). During this period, duplicate quarter milk samples were also collected for microbial analysis from all cases of CM. For an additional 16mo, cases of CM were recorded; however, no samples were collected. Quarter days at risk (62,980) were distributed among bedding types and most quarters were enrolled for >150d. Of 135 cases of SM, 63% resulted in nonsignificant growth and 87% of recovered pathogens (n=33) were identified as coagulase-negative staphylococci. The distribution of etiologies of pathogens recovered from cases of SM was associated with bedding type. Coagulase-negative staphylococci were recovered from 12, 38, 11, and 46% of quarters with SM from cows in pens containing NES, RS, DBMS, and SBMS, respectively. A result of nonsignificant growth was obtained for 81, 59, 89, and 46% of quarters with SM from cows in pens containing NES, RS, DBMS, and SBMS, respectively. Quarters of primiparous cows bedded with NES tended to have greater survival time to incidence of CM than quarters of primiparous cows bedded with RS or DBMS. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  11. Improvement of Combustion Characteristics in Fluidized Bed

    International Nuclear Information System (INIS)

    Mohamed, H.S.; El Sourougy, M.R.; Faik, M.

    2009-01-01

    The present investigation is directed towards the experimental study of the effect of a new design of the bed temperature on the overall thermal efficiency and heat transfer by conduction, convection and radiation in gaseous fuel-fluidized bed combustion system. The experiments are performed on a water-cooled fluidized bed model furnace with cylindrical cross-section of 0.25 m diameter and its height is 0.60 m. the fluidising medium used is sand particles with average diameter 1.5 mm. The bed temperature is varied between 700 degree C and 1100 degree C. Measurements f carbon dioxide, carbon monoxide and oxygen concentrations are carried out by using water-cooled sampling probe, and infrared and paramagnetic analyzers. The results obtained show that the bed temperature, the total heat transfer to the wall and the bed combustion efficiency increase with the decrease of the air-fuel ratio. It is also found that 91% of the total heat transfer is in the fluidising part of the bed and most of this heat is transferred by convection from hot sand particles to the wall. Two empirical formulae for the calculation of the wall heat transfer coefficient and the particle convective heat transfer coefficient are proposed. A verification of the proposed empirical formulae is made by comparing the calculated values with the experimental results.

  12. Condensation in Nanoporous Packed Beds.

    Science.gov (United States)

    Ally, Javed; Molla, Shahnawaz; Mostowfi, Farshid

    2016-05-10

    In materials with tiny, nanometer-scale pores, liquid condensation is shifted from the bulk saturation pressure observed at larger scales. This effect is called capillary condensation and can block pores, which has major consequences in hydrocarbon production, as well as in fuel cells, catalysis, and powder adhesion. In this study, high pressure nanofluidic condensation studies are performed using propane and carbon dioxide in a colloidal crystal packed bed. Direct visualization allows the extent of condensation to be observed, as well as inference of the pore geometry from Bragg diffraction. We show experimentally that capillary condensation depends on pore geometry and wettability because these factors determine the shape of the menisci that coalesce when pore filling occurs, contrary to the typical assumption that all pore structures can be modeled as cylindrical and perfectly wetting. We also observe capillary condensation at higher pressures than has been done previously, which is important because many applications involving this phenomenon occur well above atmospheric pressure, and there is little, if any, experimental validation of capillary condensation at such pressures, particularly with direct visualization.

  13. DEGRADATION OF AROMATIC COMPOUNDS USING MOVING BED BIOFILM REACTORS

    Directory of Open Access Journals (Sweden)

    B. Ayati, H. Ganjidoust, M. Mir Fattah

    2007-04-01

    Full Text Available For biological treatment of water, there are many different biofilm systems in use. Examples of them are trickling filters, rotating biological contactors, fixed media submerged biofilters, granular media biofilters and fluidized bed reactors. They all have their advantages and disadvantages. Hence, the Moving Bed Biofilm Reactor process was developed in Norway in the late 1980s and early 1990s to adopt the best features of the activated sludge process as well as those of the biofilter processes, without including the worst. Two cylindrical moving bed biofilm reactors were used in this study working in upflow stream conditions. Experiments have been done in aerobic batch flow regime. Laboratory experiments were conducted at room temperature (23–28C and synthetic wastewater comprising a composition of phenol and hydroquinone in each reactor as the main organic constituents, plus balanced nutrients and alkalinity were used to feed the reactor. The ratio of influent to effluent COD was determined at different retention times. The results indicated that the removal efficiency of each selected compound is affected by the detention time. At low phenol and hydroquinone concentration (from 700 to 1000 mg/L maximum removal efficiency (over 80 % was obtained. By further increasing in COD loading rate up to 3000 mg/L, a decrease in COD removal rate was occurred. In the reactor containing pyrogallol in COD of 1500 mg/L, the removal rate decreased to 10 percent because of its toxicity for microorganisms.

  14. Anaerobic treatment of winery wastewater in fixed bed reactors.

    Science.gov (United States)

    Ganesh, Rangaraj; Rajinikanth, Rajagopal; Thanikal, Joseph V; Ramanujam, Ramamoorty Alwar; Torrijos, Michel

    2010-06-01

    The treatment of winery wastewater in three upflow anaerobic fixed-bed reactors (S9, S30 and S40) with low density floating supports of varying size and specific surface area was investigated. A maximum OLR of 42 g/l day with 80 +/- 0.5% removal efficiency was attained in S9, which had supports with the highest specific surface area. It was found that the efficiency of the reactors increased with decrease in size and increase in specific surface area of the support media. Total biomass accumulation in the reactors was also found to vary as a function of specific surface area and size of the support medium. The Stover-Kincannon kinetic model predicted satisfactorily the performance of the reactors. The maximum removal rate constant (U(max)) was 161.3, 99.0 and 77.5 g/l day and the saturation value constant (K(B)) was 162.0, 99.5 and 78.0 g/l day for S9, S30 and S40, respectively. Due to their higher biomass retention potential, the supports used in this study offer great promise as media in anaerobic fixed bed reactors. Anaerobic fixed-bed reactors with these supports can be applied as high-rate systems for the treatment of large volumes of wastewaters typically containing readily biodegradable organics, such as the winery wastewater.

  15. Assessment of capability of models for prediction of pressure drop and dryout heat flux in a heat generating particulate debris bed

    International Nuclear Information System (INIS)

    Kulkarni, P.P.; Nayak, A.K.; Rashid, M.; Kulenovic, R.

    2009-01-01

    During a severe accident in a light water reactor, the core can melt and be relocated to the lower plenum of the reactor pressure vessel. There it can form a particulate debris bed due to the possible presence of water. This bed, if not quenched in time, can lead to the failure of the pressure vessel because of the insufficient heat removal of decay heat in the debris bed. Therefore, addressing the issue of coolability behaviour of heat generating particulate debris bed is of prime importance in the framework of severe accident management strategies, particularly in case of above mentioned late phase scenario of an accident. In order to investigate the coolability behaviour of particulate debris bed, experiments were carried out at IKE test facility 'DEBRIS' on particle beds of irregularly shaped particles mixed with spheres under top- and bottom-flooding condition. The pressure drop and dryout heat flux (DHF) were measured for top- and bottom-flooding conditions. For top-flooding conditions, it was found that the pressure gradients are all smaller than the hydrostatic pressure gradient of water, indicating an important role of the counter-current interfacial shear stress of the two-phase flow. For bottom-flooding with a relatively high liquid inflow velocity, the pressure gradient increases consistently with the vapour velocity and the fluid-particle drags become important. Also, with additional forced liquid inflow from the bottom, the DHF increases dramatically. In all the cases, it was found that the DHF is significantly larger with bottom-flooding condition compared to top-flooding condition. Different models such as Lipinski, Reed, Tung and Dhir, Hu and Theophanous, and Schulenberg and Mueller have been used to predict the pressure drop characteristics and the DHF of heat generating particulate debris beds. Comparison is made among above mentioned models and experimental results for DHF and pressure drop characteristics. Considering the overall trend in

  16. Recent advances in fluidized bed drying

    Science.gov (United States)

    Haron, N. S.; Zakaria, J. H.; Mohideen Batcha, M. F.

    2017-09-01

    Fluidized bed drying are very well known to yield high heat and mass transfer and hence adopted to many industrial drying processes particularly agricultural products. In this paper, recent advances in fluidized bed drying were reviewed and focus is given to the drying related to the usage of Computational Fluid Dynamics (CFD). It can be seen that usage of modern computational tools such as CFD helps to optimize the fluidized bed dryer design and operation for lower energy consumption and thus better thermal efficiency. Among agricultural products that were reviewed in this paper were oil palm frond, wheat grains, olive pomace, coconut, pepper corn and millet.

  17. Designs that make a difference: the Cardiac Universal Bed model.

    Science.gov (United States)

    Johnson, Jackie; Brown, Katherine Kay; Neal, Kelly

    2003-01-01

    Information contained in this article includes some of the findings from a joint research project conducted by Corazon Consulting and Ohio State University Medical Center on national trends in Cardiac Universal Bed (CUB) utilization. This article outlines current findings and "best practice" standards related to the benefits of developing care delivery models to differentiate an organization with a competitive advantage in the highly dynamic marketplace of cardiovascular care. (OSUMC, a Corazon client, is incorporating the CUB into their Ross Heart Hospital slated to open this spring.)

  18. SPOUTED BED DESIGN CONSIDERATIONS FOR COATED NUCLEAR FUEL PARTICLES

    Energy Technology Data Exchange (ETDEWEB)

    Marshall, Douglas W.

    2017-07-01

    High Temperature Gas Cooled Reactors (HTGRs) are fueled with tristructural isotropic (TRISO) coated nuclear fuel particles embedded in a carbon-graphite fuel body. TRISO coatings consist of four layers of pyrolytic carbon and silicon carbide that are deposited on uranium ceramic fuel kernels (350µm – 500µm diameters) in a concatenated series of batch depositions. Each layer has dedicated functions such that the finished fuel particle has its own integral containment to minimize and control the release of fission products into the fuel body and reactor core. The TRISO coatings are the primary containment structure in the HTGR reactor and must have very high uniformity and integrity. To ensure high quality TRISO coatings, the four layers are deposited by chemical vapor deposition (CVD) using high purity precursors and are applied in a concatenated succession of batch operations before the finished product is unloaded from the coating furnace. These depositions take place at temperatures ranging from 1230°C to 1550°C and use three different gas compositions, while the fuel particle diameters double, their density drops from 11.1 g/cm3 to 3.0 g/cm3, and the bed volume increases more than 8-fold. All this is accomplished without the aid of sight ports or internal instrumentation that could cause chemical contamination within the layers or mechanical damage to thin layers in the early stages of each layer deposition. The converging section of the furnace retort was specifically designed to prevent bed stagnation that would lead to unacceptably high defect fractions and facilitate bed circulation to avoid large variability in coating layer dimensions and properties. The gas injection nozzle was designed to protect precursor gases from becoming overheated prior to injection, to induce bed spouting and preclude bed stagnation in the bottom of the retort. Furthermore, the retort and injection nozzle designs minimize buildup of pyrocarbon and silicon carbide on the

  19. Ion leakage from mixed beds in condensate polishing plants

    International Nuclear Information System (INIS)

    Venderbosch, H.W.; Overman, L.J.; Snel, A.

    1977-01-01

    In view to the interest for theoretical and practical factors, which influence the ion slip of mixed bed filters, these facts were studied in detail. It proved to be necessary that the slip shall be subdivided into kinetic - and elution slip. The kinetic slip is depending e.g. on the electrolyte concentration of the influenct condensate, as well as on the period of contact, however it does not depend on the regeneration condition; the elution slip however depends clearly on the regeneration condition. Incomplete regeneration of the exchangers, a too low excess of regenerant, incomplete separation of cation - and anion exchanger, and the contact of an exchanger layer with the wrong regenerant in the separation zone, during the internal regeneration are raising the slip. With tests on mixed bed filters, which have been well regenerated, (less than 0.1% Na in the cation exchanger) and by using filters with normal regenerated exchangers, (approx. 10% Na in the cation exchanger) the quality of the effluent was compared with values, which were expected from calculations. In order to decrease the elution leakage, the contamination of the exchangers, especially at NH 4 OH - mixed bed filters, must be limited to a very low percentage. Several possibilities to obtain this, will be discussed in the lecture. Special attention will be paid to the internal regeneration procedure. KEMA has developed a method, the so-called partial regeneration method, in order to operate internal regenerated mixed bed filters, which have been designed for the HOH cycle, also in the ammonia form, without the occurence of an undue slip of sodium or chloride. Not only extended running periods and lower operating- and regeneration costs are of advantage, but also the reducing of salt- and ammonia containing sewage were achieved. (orig.) [de

  20. Bed Bug Infestations and Control Practices in China: Implications for Fighting the Global Bed Bug Resurgence

    Directory of Open Access Journals (Sweden)

    Changlu Wang

    2011-04-01

    Full Text Available The bed bug resurgence in North America, Europe, and Australia has elicited interest in investigating the causes of the widespread and increasing infestations and in developing more effective control strategies. In order to extend global perspectives on bed bug management, we reviewed bed bug literature in China by searching five Chinese language electronic databases. We also conducted telephone interviews of 68 pest control firms in two cities during March 2011. In addition, we conducted telephone interviews to 68 pest control companies within two cities in March 2011. Two species of bed bugs (Cimex lectularius L. and Cimex hemipterus (F. are known to occur in China. These were common urban pests before the early1980s. Nationwide “Four-Pest Elimination” campaigns (bed bugs being one of the targeted pests were implemented in China from 1960 to the early 1980s. These campaigns succeeded in the elimination of bed bug infestations in most communities. Commonly used bed bug control methods included applications of hot water, sealing of bed bug harborages, physical removal, and applications of residual insecticides (mainly organophosphate sprays or dusts. Although international and domestic travel has increased rapidly in China over the past decade (2000–2010, there have only been sporadic new infestations reported in recent years. During 1999–2009, all documented bed bug infestations were found in group living facilities (military dormitories, worker dormitories, and prisons, hotels, or trains. One city (Shenzhen city near Hong Kong experienced significantly higher number of bed bug infestations. This city is characterized by a high concentration of migratory factory workers. Current bed bug control practices include educating residents, washing, reducing clutter, putting items under the hot sun in summer, and applying insecticides (pyrethroids or organophosphates. There have not been any studies or reports on bed bug insecticide

  1. Evaluation of a clay-based acidic bedding conditioner for dairy cattle bedding.

    Science.gov (United States)

    Proietto, R L; Hinckley, L S; Fox, L K; Andrew, S M

    2013-02-01

    This study investigated the effects of a clay-based acidic bedding conditioner on sawdust bedding pH, dry matter (DM), environmental pathogen counts, and environmental bacterial counts on teat ends of lactating dairy cows. Sixteen lactating Holstein cows were paired based on parity, days in milk, milk yield, and milk somatic cell count, and were negative for the presence of an intramammary pathogen. Within each pair, cows were randomly assigned to 1 of 2 treatments with 3-wk periods in a crossover design. Treatment groups consisted of 9 freestalls per group bedded with either untreated sawdust or sawdust with a clay-based acidic bedding conditioner, added at 3- to 4-d intervals over each 21-d period. Bedding and teat ends were aseptically sampled on d 0, 1, 2, 7, 14, and 21 for determination of environmental bacterial counts. At the same time points, bedding was sampled for DM and pH determination. The bacteria identified in the bedding material were total gram-negative bacteria, Streptococcus spp., and coliform bacteria. The bacteria identified on the teat ends were Streptococcus spp., coliform bacteria, and Klebsiella spp. Teat end score, milk somatic cell count, and intramammary pathogen presence were measured weekly. Bedding and teat cleanliness, environmental high and low temperatures, and dew point data were collected daily. The bedding conditioner reduced the pH, but not the DM, of the sawdust bedding compared with untreated sawdust. Overall environmental bacterial counts in bedding were lower for treated sawdust. Total bacterial counts in bedding and on teat ends increased with time over both periods. Compared with untreated sawdust, the treated bedding had lower counts of total gram-negative bacteria and streptococci, but not coliform counts. Teat end bacterial counts were lower for cows bedded on treated sawdust for streptococci, coliforms, and Klebsiella spp. compared with cows bedded on untreated sawdust. The clay-based acidic bedding conditioner

  2. Filtered containment venting in Sweden

    International Nuclear Information System (INIS)

    Lindau, L.; Ellisson, K.

    1989-01-01

    After the TMI accident, Swedish authorities decided that all Swedish nuclear power plants should be upgraded with respect to mitigation of the consequences of severe accidents. One contribution to meet these ends is filtered containment venting, i.e. means to relieve containment overpressure and to clean the relief gas from radioactive components. The first system in operation was built at the Barsebaeck site (2 BWR's) where a gravel bed filter was installed. For the remaining Swedish units (7 BWR's and 3 PWR's) a passive, self-controlling wet scrubber system, FILTRA-MVSS, is now under installation. The principle of the FILTRA-MVSS is a self-controlling, self-pumping venturi collector submerged in a pool, and it is used to filter out emissions of solid and gaseous radioactive components

  3. Modelling glacier-bed overdeepenings and possible future lakes for the glaciers in the Himalaya-Karakoram region

    DEFF Research Database (Denmark)

    Linsbauer, A.; Frey, H.; Haeberli, W.

    2016-01-01

    Surface digital elevation models (DEMs) and slope-related estimates of glacier thickness enable modelling of glacier-bed topographies over large ice-covered areas. Due to the erosive power of glaciers, such bed topographies can contain numerous overdeepenings, which when exposed following glacier...... retreat may fill with water and form new lakes. In this study, the bed overdeepenings for ∼28000 glaciers (40 775km2) of the Himalaya-Karakoram region are modelled using GlabTop2 (Glacier Bed Topography model version 2), in which ice thickness is inferred from surface slope by parameterizing basal shear...... stress as a function of elevation range for each glacier. The modelled ice thicknesses are uncertain (±30%), but spatial patterns of ice thickness and bed elevation primarily depend on surface slopes as derived from the DEM and, hence, are more robust. About 16 000 overdeepenings larger than 104m2 were...

  4. Medications to Treat Bed-Wetting

    Science.gov (United States)

    ... suggest that depression plays a role in the cause of bed-wetting. This type of drug is thought to work one of several ways: by changing the child's sleep and wakening pattern by affecting the time ...

  5. Bed Bug Clearinghouse by Type of Resource

    Science.gov (United States)

    This information is to help states, communities, and consumers prevent and control bed bug infestations. These brochures, fact sheets, manuals, posters, checklists, videos, and more provide guidance such as hotel room inspection and pesticide safety.

  6. Bed Bugs are Public Health Pests

    Science.gov (United States)

    EPA and the Centers for Disease Control and Prevention (CDC) issued a joint statement on the public health impacts of bed bugs, which are blood-sucking ectoparasites (external parasites). EPA also has a pesticide registration notice on this topic.

  7. The effect of vibration on bed voidage behaviors in fluidized beds with large particles

    Directory of Open Access Journals (Sweden)

    H. Jin

    2007-09-01

    Full Text Available The effects of vibration parameters, operating conditions and material properties on bed voidage were investigated using an optical fiber probe approach in a vibrating fluidized bed with a diameter of 148 mm. Variables studied included frequency (0-282 s-1, amplitude (0 mm-1 mm, bed height (0.1 m-0.4 m as well as four kinds of particles (belonging to Geldart's B and D groups. The axial and radial voidage distribution with vibration is compared with that without vibration, which shows vibration can aid in the fluidization behaviors of particles. For a larger vibration amplitude, the vibration seriously affects bed voidage. The vibration energy can damp out for particle layers with increasing the bed height. According to analysis of experimental data, an empirical correlation for predicting bed voidage, giving good agreement with the experimental data and a deviation within ±15%, was proposed.

  8. Fluidized combustion of beds of large, dense particles in reprocessing HTGR fuel

    International Nuclear Information System (INIS)

    Young, D.T.

    1977-03-01

    Fluidized bed combustion of graphite fuel elements and carbon external to fuel particles is required in reprocessing high-temperature gas-cooled reactor (HTGR) cores for recovery of uranium. This burning process requires combustion of beds containing both large particles and very dense particles as well as combustion of fine graphite particles which elutriate from the bed. Equipment must be designed for optimum simplicity and reliability as ultimate operation will occur in a limited access ''hot cell'' environment. Results reported in this paper indicate that successful long-term operation of fuel element burning with complete combustion of all graphite fines leading to a fuel particle product containing <1% external carbon can be performed on equipment developed in this program

  9. Coolability of volumetrically heated particle beds

    Energy Technology Data Exchange (ETDEWEB)

    Rashid, Muhammad

    2017-03-22

    In case of a severe nuclear reactor accident, with loss of coolant, a particle bed may be formed from the fragmentation of the molten core in the residual water at different stages of the accident. To avoid further propagation of the accident and maintain the integrity of the reactor pressure vessel, the decay heat of the particle bed must be removed. To better understand the various thermo-hydraulic processes within such heat-generating particle beds, the existing DEBRIS test facility at IKE has been modified to be able to perform novel boiling, dryout and quenching experiments. The essential experimental data includes the pressure gradients measured by 8 differential pressure transducers along the bed height as a function of liquid and vapour superficial velocities, the determination of local dryout heat fluxes for different system pressures as well as the local temperature distribution measured by a set of 51 thermocouples installed inside the particle bed. The experiments were carried out for two different particle beds: a polydispersed particle bed which consisted of stainless steel balls (2 mm, 3 mm and 6 mm diameters) and an irregular particle bed which consisted of a mixture of steel balls (3 mm and 6 mm) and irregularly shaped Al{sub 2}O{sub 3} particles. Additionally, all experiments were carried out for different flow conditions, such as the reference case of passive 1D top-flooding, 1D bottom flooding (driven by external pumps and different downcomer configurations) and 2D top-/bottom-/lateral flooding with a perforated downcomer. In this work, it has been observed that for both particle beds with downcomer configurations an open downcomer leads to the best coolability (dryout heat flux = 1560 kW/m{sup 2}, polydispersed particle bed, psys = 1 bar) of the particle bed, mainly due to bottom-flow with enhanced natural convection. It has also been shown that a potential lateral flow via a perforation of the downcomer does not bring any further improvements

  10. Coolability of volumetrically heated particle beds

    International Nuclear Information System (INIS)

    Rashid, Muhammad

    2017-01-01

    In case of a severe nuclear reactor accident, with loss of coolant, a particle bed may be formed from the fragmentation of the molten core in the residual water at different stages of the accident. To avoid further propagation of the accident and maintain the integrity of the reactor pressure vessel, the decay heat of the particle bed must be removed. To better understand the various thermo-hydraulic processes within such heat-generating particle beds, the existing DEBRIS test facility at IKE has been modified to be able to perform novel boiling, dryout and quenching experiments. The essential experimental data includes the pressure gradients measured by 8 differential pressure transducers along the bed height as a function of liquid and vapour superficial velocities, the determination of local dryout heat fluxes for different system pressures as well as the local temperature distribution measured by a set of 51 thermocouples installed inside the particle bed. The experiments were carried out for two different particle beds: a polydispersed particle bed which consisted of stainless steel balls (2 mm, 3 mm and 6 mm diameters) and an irregular particle bed which consisted of a mixture of steel balls (3 mm and 6 mm) and irregularly shaped Al 2 O 3 particles. Additionally, all experiments were carried out for different flow conditions, such as the reference case of passive 1D top-flooding, 1D bottom flooding (driven by external pumps and different downcomer configurations) and 2D top-/bottom-/lateral flooding with a perforated downcomer. In this work, it has been observed that for both particle beds with downcomer configurations an open downcomer leads to the best coolability (dryout heat flux = 1560 kW/m 2 , polydispersed particle bed, psys = 1 bar) of the particle bed, mainly due to bottom-flow with enhanced natural convection. It has also been shown that a potential lateral flow via a perforation of the downcomer does not bring any further improvements in

  11. Uranium storage bed accident hazards evaluation

    International Nuclear Information System (INIS)

    Longhurst, G.R.; Shmayda, W.T.

    1989-01-01

    To properly assess hazards and risks associated with the use of uranium beds as tritium storage devices in fusion reactor systems, it is necessary to understand the consequences occurring in the event of an accident. Accidents involving uranium beds are postulated, and the possible results are considered. A research program to more fully and accurately understand those results has been initiated involving the Idaho National Engineering Laboratory and Ontario Hydro. The plan and objectives of that program are presented. 11 refs., 1 tab

  12. Uranium storage bed accident hazards evaluation

    International Nuclear Information System (INIS)

    Longhurst, G.R.; Shmayda, W.T.

    1989-10-01

    To properly assess hazards and risks associated with the use of uranium beds as tritium storage devices in fusion reactor systems, it is necessary to understand the consequences occurring in the event of an accident. Accidents involving uranium beds are postulated, and the possible results are considered. A research program to more fully and accurately understand those results has been initiated involving the Idaho National Engineering Laboratory and Ontario Hydro. The plan and objectives of that program are presented. 11 refs., 1 tab

  13. Hydrodynamics of circulating and bubbling fluidized beds

    International Nuclear Information System (INIS)

    Gidaspow, D.P.; Tsuo, Y.P.; Ding, J.

    1991-01-01

    This paper reports that a review of modeling of the hydrodynamics of fluidization of bubbling beds showed that inviscid two-fluid models were able to predict a great deal of the behavior of bubbling beds because the dominant mechanism of energy dissipation is the drag between the particles and the fluid. The formation, the growth and the bursting of bubbles were predicted. Predicted wall-to-bed heat transfer coefficients and velocity profiles of jets agreed with measurements. Time average porosity distributions agreed with measurements done using gamma-ray densitometers without the use of any adjustable parameters. However, inviscid models could not correctly predict rates of erosion around tubes immersed into fluidized beds. To correctly model such behavior, granular stresses involving solids viscosity were added into the computer model. This viscosity arises due to random collision of particles. Several models fro this viscosity were investigated and the results compared to measurements of solids distributions in two-dimensional beds and to particle velocities reported in the literature. While in the case of bubbling beds the solids viscosity plays the role of a correction, modeling of a circulating fluidized bed (CFB) without a viscosity is not possible. Recent experimental data obtained at IIT and at IGT show that in CFB the solids viscous dissipation is responsible for as much as half of the pressure drop. From such measurement, solids viscosities were computed. These were used in the two fluid hydrodynamic model, to predict radial solids distributions and solids velocities which matched the experimental distributions. Most important, the model predicted cluster formation and transient internal circulation which is responsible for the favorable characteristics of CFBs, such as good wall-to-bed heat transfer. Video tape movies of computations compared favorably with high speed movies of the experiments

  14. FLUIDIZED BED STEAM REFORMER MONOLITH FORMATION

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C

    2006-12-22

    Fluidized Bed Steam Reforming (FBSR) is being considered as an alternative technology for the immobilization of a wide variety of aqueous high sodium containing radioactive wastes at various DOE facilities in the United States. The addition of clay, charcoal, and a catalyst as co-reactants converts aqueous Low Activity Wastes (LAW) to a granular or ''mineralized'' waste form while converting organic components to CO{sub 2} and steam, and nitrate/nitrite components, if any, to N{sub 2}. The waste form produced is a multiphase mineral assemblage of Na-Al-Si (NAS) feldspathoid minerals with cage-like structures that atomically bond radionuclides like Tc-99 and anions such as SO{sub 4}, I, F, and Cl. The granular product has been shown to be as durable as LAW glass. Shallow land burial requires that the mineralized waste form be able to sustain the weight of soil overburden and potential intrusion by future generations. The strength requirement necessitates binding the granular product into a monolith. FBSR mineral products were formulated into a variety of monoliths including various cements, Ceramicrete, and hydroceramics. All but one of the nine monoliths tested met the <2g/m{sup 2} durability specification for Na and Re (simulant for Tc-99) when tested using the Product Consistency Test (PCT; ASTM C1285). Of the nine monoliths tested the cements produced with 80-87 wt% FBSR product, the Ceramicrete, and the hydroceramic produced with 83.3 wt% FBSR product, met the compressive strength and durability requirements for an LAW waste form.

  15. The Physiology of Bed Rest. Chapter 39

    Science.gov (United States)

    Fortney, Suzanne M.; Schneider, Victor S.; Greenleaf, John E.

    1996-01-01

    Prolonged rest in bed has been utilized by physicians and other health-care workers to immobilize and confine patients for rehabilitation and restoration of health since time immemorial. The sitting or horizontal position is sought by the body to relieve the strain of the upright or vertical postures, for example during syncopal situations, bone fractures, muscle injuries, fatigue, and probably also to reduce energy expenditure. Most health-care personnel are aware that adaptive responses occurring during bed rest proceed concomitantly with the healing process; signs and symptoms associated with the former should be differentiated from those of the latter. Not all illnesses and infirmities benefit from prolonged bed rest. Considerations in prescribing bed rest for patients-including duration, body position, mode and duration of exercise, light-dark cycles, temperature, and humidity-have not been investigated adequately. More recently, adaptive physiological responses have been measured in normal, healthy subjects in the horizontal or slightly head-down postures during prolonged bed rest as analogs for the adaptive responses of astronauts exposed to the microgravity environment of outer and bed-rest research.

  16. Fluidized bed volume reduction of diverse radwastes

    International Nuclear Information System (INIS)

    McFee, J.N.; McConnell, J.W.; Waddoups, D.A.; Gray, M.F.; Harwood, L.E.; Clayton, N.J.; Drown, D.C.

    1981-01-01

    Method and apparatus for a fluidized bed radwaste volume reduction system are claimed. Low level radioactive wastes, combustible solids, ion exchange resins and filter sludges, and liquids, emanating from a reactor facility are introduced separately through an integrated waste influent system into a common fluidized bed vessel where volume reduction either through incineration or calcination occurs. Addition of a substance to the ion exchange resin before incineration inhibits the formation of low-melting point materials which tend to form clinkers in the bed. Solid particles are scrubbed or otherwise removed from the gaseous effluent of the vessel in an off-gas system, before the cooled and cleaned off-gas is released to the atmosphere. Iodine is chemically or physically removed from the off-gas. Otherwise, the only egress materials from the volume reduction system are containerized dry solids and tramp material. The bed material used during each mode may be circulated, cleaned, stored and exchanged from within the bed vessel by use of a bed material handling system. An instrumentation and control system provides operator information, monitors performance characteristics, implements start up and shut down procedures, and initiates alarms and emergency procedures during abnormal conditions

  17. WTP Pretreatment Facility Potential Design Deficiencies--Sliding Bed and Sliding Bed Erosion Assessment

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, E. K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-05-06

    This assessment is based on readily available literature and discusses both Newtonian and non-Newtonian slurries with respect to sliding beds and erosion due to sliding beds. This report does not quantify the size of the sliding beds or erosion rates due to sliding beds, but only assesses if they could be present. This assessment addresses process pipelines in the Pretreatment (PT) facility and the high level waste (HLW) transfer lines leaving the PT facility to the HLW vitrification facility concentrate receipt vessel.

  18. WTP Pretreatment Facility Potential Design Deficiencies--Sliding Bed and Sliding Bed Erosion Assessment

    International Nuclear Information System (INIS)

    Hansen, E. K.

    2015-01-01

    This assessment is based on readily available literature and discusses both Newtonian and non-Newtonian slurries with respect to sliding beds and erosion due to sliding beds. This report does not quantify the size of the sliding beds or erosion rates due to sliding beds, but only assesses if they could be present. This assessment addresses process pipelines in the Pretreatment (PT) facility and the high level waste (HLW) transfer lines leaving the PT facility to the HLW vitrification facility concentrate receipt vessel.

  19. Control of the Bed Temperature of a Circulating Fluidized Bed Boiler by using Particle Swarm Optimization

    Directory of Open Access Journals (Sweden)

    AYGUN, H.

    2012-05-01

    Full Text Available Circulating fluidized bed boilers are increasingly used in the power generation due to their higher combustion efficiency and lower pollutant emissions. Such boilers require an effective control of the bed temperature, because it influences the boiler combustion efficiency and the rate of harmful emissions. A Particle-Swarm-Optimization-Proportional-Integrative-Derivative (PSO-PID controller for the bed temperature of a circulating fluidized bed boiler is presented. In order to prove the capability of the proposed controller, its performances are compared at different boiler loads with those of a Fuzzy Logic (FL controller. The simulation results demonstrate some advantages of the proposed controller.

  20. Effect of bed configuration on pebble flow uniformity and stagnation in the pebble bed reactor

    International Nuclear Information System (INIS)

    Gui, Nan; Yang, Xingtuan; Tu, Jiyuan; Jiang, Shengyao

    2014-01-01

    Highlights: • Pebble flow uniformity and stagnation characteristics are very important for HTR-PM. • Arc- and brachistochrone-shaped configuration effects are studied by DEM simulation. • Best bed configurations with uniform flow and no stagnated pebbles are suggested. • Detailed quantified characteristics of bed configuration effects are shown for explanation. - Abstract: Pebble flow uniformity and stagnation characteristics are very important for the design of pebble bed high temperature gas-cooled reactor. Pebble flows inside some specifically designed contraction configurations of pebble bed are studied by discrete element method. The results show the characteristics of stagnation rates, recycling rates, radial distribution of pebble velocity and residence time. It is demonstrated clearly that the bed with a brachistochrone-shaped configuration achieves optimum levels of flow uniformity and recycling rate concentration, and almost no pebbles are stagnated in the bed. Moreover, the optimum choice among the arc-shaped bed configurations is demonstrated too. Detailed information shows the quantified characteristics of bed configuration effects on flow uniformity. In addition, a good design of the pebble bed configuration is suggested