Experimental Investigation on Asphalt Binders Ageing Behavior and Rejuvenating Feasibility in Multicycle Repeated Ageing and Recycling

Directory of Open Access Journals (Sweden)

Yihua Nie

2018-01-01

Full Text Available Multicycle repeated utilization of reclaimed asphalt pavement (RAP is a quite recent development of sustainable pavement materials technology. To investigate ageing rules and recycling possibility of asphalt binders in repeatedly used asphalt mixture, virgin asphalt AH-70 samples were heated by the rolling thin film oven test (RTFOT at 163°C, respectively, for 40, 85, 180, 240, and 300 minutes to simulate different ageing degrees, and then the aged ones were rejuvenated by adding a self-made rejuvenator. This ageing and recycling process was repeated altogether for 5 cycles to simulate repeated use of RAP binders. In repeated recycling, rejuvenator contents for different cycle numbers or ageing durations were not the same, and the optimum ones were initially estimated by an empirical formula and finally obtained by comparative tests. Empirical rheological tests and the infrared spectral (IR analysis were done before and after each cycle of recycling. Results indicate that for impact on deterioration of asphalt binders, ageing time is more important than cycle number. Meanwhile, the asphalt after multicycle repeated ageing and recycling can be restored to the empirical rheological indices level of the virgin asphalt and meet specifications requirements.

Tire-Pavement Friction Characteristics with Elastic Properties of Asphalt Pavements

Directory of Open Access Journals (Sweden)

Miao Yu

2017-11-01

Full Text Available The skid-resisting performance of pavement is a critical factor in traffic safety. Recent studies primarily analyze this behavior by examining the macro or micro texture of the pavement. It is inevitable that skid-resistance declines with time because the texture of pavement deteriorates throughout its service life. The primary objective of this paper is to evaluate the use of different asphalt pavements, varying in resilience, to optimize braking performance on pavement. Based on the systematic dynamics of tire-pavement contact, and analysis of the tire-road coupled friction mechanism and the effect of enlarging the tire-pavement contact area, road skid resistance was investigated by altering the elastic modulus of asphalt pavement. First, this research constructed the kinetic contact model to simulate tire-pavement friction. Next, the following aspects of contact behaviors were studied when braking: tread deformation in the tangential pavement interface, actual tire-pavement contact in the course, and the frictional braking force transmitted from the pavement to the tires. It was observed that with improvements in pavement elasticity, the actual tire-pavement contact area increased, which gives us the ability to effectively strengthen the frictional adhesion of the tire to the pavement. It should not be overlooked that the improvement in skid resistance was caused by an increase in pavement elasticity. This research approach provides a theoretical basis and design reference for the anti-skid research of asphalt pavements.

Durable Recycled Superpave Mixes in Kansas

Science.gov (United States)

2018-04-01

The use of economical and environment-friendly recycled asphalt materials has become increasingly popular for asphalt pavement construction. In general, reclaimed asphalt pavement (RAP) and recycled asphalt shingles (RAS) are used in hot-mix asphalt ...

Sustainable Performance of Iraqi Asphalt Base Course Using Recycled Glass as Aggregate Replacement

Directory of Open Access Journals (Sweden)

Hamid Athab Eedan Al-Jameel

2018-03-01

Full Text Available Nowadays, a lot of waste glass produced through different sides of life. Applying sustainability has been widely used in different construction materials and flexible pavement was contained different recycled materials through different studies. Recycled glass, where it is nonmetallic and inorganic, it can neither be incinerated nor decomposed, so it may be difficult to reclaim, has been used as filler, fine and coarse aggregates in the asphalt base course. In this study, various standard asphalt tests, such as stability, flow, density and air voids, have been conducted on reference mix asphalt and mix asphalt with different percentages of recycled glass when it has been used as filler, fine and coarse aggregates in the base course. Generally, the results show good indication, especially when using 10% of the recycled glass instead of coarse aggregate with 40-50 asphalt grades. This percentage improves most characteristics such as strength retained index which indicates better performance than reference mix.  

Investigation of the use of recycled polymer-modified asphalt in asphaltic concrete pavements.

Science.gov (United States)

2004-06-30

This report presents issues associated with recycling polymer modified asphalt cements (PMACs), particularly blending aged PMAC with new PMAC. A styrene-butadiene-styrene (SBS) PMAC was selected and graded using the Superpave Performance Grading (PG)...

Rheo-mechanical model for self-healing asphalt pavement

International Nuclear Information System (INIS)

Gömze, A L; Gömze, L N

2017-01-01

Examining the rheological properties of different asphalt mixtures at different temperatures, pressures and deformation conditions on the combined rheo-tribometers the authors have found that the generally used Burgers-model doesn’t explain the deformation properties of asphalt mixtures and pavements under loading forces and loading pressures. To understand better the rheological and deformation properties of such complex materials like asphalt mixtures and pavements the authors used Malvern Mastersizer X laser granulometer, Bruker D8 Advance X-ray diffractometer, Hitachi TM 1000 Scanning Elektronmicroscope, Tristar 3000 specific surface tester and the combined rheo-tribometer developed and patented by the authors. After the complex investigation of different asphalt mixtures the authors have found a new, more complex rheological model for the asphalts including self-healing asphalt pavements. (paper)

Installation report : evaluation of recycled hot mix asphaltic concrete on Route 220.

Science.gov (United States)

1982-01-01

This report describes a project in which the bituminous pavement on an approximately 8-mi. (13-km) section of roadway was removed, recycled through a conventional asphalt batch plant, and relaid. The project was accomplished with little difficulty an...

Modified asphalt for pavements; Hosoyo kaishitsu asufuaruto ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Tsukagoshi, T. [Nippon Oil Co. Ltd., Yokohama (Japan)

1997-10-01

Modified asphalt has been used widely in such applications as countermeasure against rutting, countermeasure against wear caused by tire chains in snowy and cold areas, or bridge deck pavement. Features of various kinds of modified asphalt, standards, and standard properties are introduced. Modified asphalt containing natural asphalt is used for steel plate deck pavement. Semi-blown asphalt is used when emphasis must be given to the countermeasure for flowing resistance of asphalt pavement. Features and standards of asphalt containing rubber, thermoplastic elastomer, and thermoplastic resin are described. Asphalt containing heat-setting resin shows excellent characteristics, which other types of modified asphalt do not possess, in the laboratory resistance test for fatigue, flowing, and wear. Change in the history of modified asphalt in Japan from the initial stage to the present are explained and shown in a table together with time and phenomena, and the change in the production of modified asphalt is shown. 15 refs., 5 figs., 5 tabs.

Experimental Study on Color Durability of Color Asphalt Pavement

Science.gov (United States)

Ning, Shi; Huan, Su

2017-06-01

Aiming at the poor Color durability and the lack of research on Color asphalt pavement, spraying an anti-tire trace seal resin emulsion on the surface, a Color durable asphalt pavement was proposed. After long-term rolling and long-term aging test, the Color durability was evaluated by RGB function in Photoshop and trace residue rate formula. Test results proved that the Evaluation method was simple and effective. After long-term rolling, the Color of the road surface tends to a constant value. Spraying the emulsion on the road surface can resist tire traces. After long-term aging test, the resistance to tire traces was increased by 26.6% compared with the conventional type, while the former was 44.1% higher than the latter without long-term aging. The Color durable asphalt pavement can effectively improve the ability of Color asphalt pavement to resist tire traces, and significantly improve the Color durability of Color asphalt pavement.

Viscoelastic behaviour of cold recycled asphalt mixes

Science.gov (United States)

Cizkova, Zuzana; Suda, Jan

2017-09-01

Behaviour of cold recycled mixes depends strongly on both the bituminous binder content (bituminous emulsion or foamed bitumen) and the hydraulic binder content (usually cement). In the case of cold recycled mixes rich in bitumen and with low hydraulic binder content, behaviour is close to the viscoelastic behaviour of traditional hot mix asphalt. With decreasing bituminous binder content together with increasing hydraulic binder content, mixes are characteristic with brittle behaviour, typical for concrete pavements or hydraulically bound layers. The behaviour of cold recycled mixes with low content of both types of binders is similar to behaviour of unbound materials. This paper is dedicated to analysing of the viscoelastic behaviour of the cold recycled mixes. Therefore, the tested mixes contained higher amount of the bituminous binder (both foamed bitumen and bituminous emulsion). The best way to characterize any viscoelastic material in a wide range of temperatures and frequencies is through the master curves. This paper includes interesting findings concerning the dependency of both parts of the complex modulus (elastic and viscous) on the testing frequency (which simulates the speed of heavy traffic passing) and on the testing temperature (which simulates the changing climate conditions a real pavement is subjected to).

Long-term aging of recycled binders.

Science.gov (United States)

2015-07-01

Asphalt pavement is Americas most recycled material. Eighty million tons of asphalt, nearly 80% of all milled asphalt pavement, : is recycled every year [1]. To effectively maintain its 40,000 miles of paved roads, the Florida Department of Transp...

Analysis of stiffness and fatigue resistance of cold recycled asphalt mixtures manufactured with foamed bitumen for their application to airfield pavement design

Directory of Open Access Journals (Sweden)

H. I. Lacalle-Jiménez

2017-07-01

Full Text Available Cold recycled bound materials (CRBMs provide an economic and environmental advantage for pavements since they decrease energy and raw material consumption. However, design methods for airfield pavements do not include key CRBM properties. In this paper an empirical-mechanistic method is used to study airfield pavement design with CRBM in order to develop design guidance. The aim of the paper is to obtain the inputs related to material properties needed for use in this method. For this purpose, CRBM containing reclaimed asphalt, with fly ash, cement and foamed bitumen as stabilising agents, was characterised. The methodology included indirect tensile stiffness modulus (ITSM and indirect tensile fatigue tests (ITFT in strain control mode. The inputs needed for a pavement design analysis with CRBM were then obtained. The results showed the importance of further study on CRBM fatigue to understand the behaviour of these mixes under cyclic loading.

Numerical simulation on the thermal response of heat-conducting asphalt pavements

Energy Technology Data Exchange (ETDEWEB)

Wang Hong; Wu Shaopeng; Chen Mingyu; Zhang Yuan, E-mail: wusp@whut.edu.c [Key Laboratory of Silicate Materials Science and Engineering, Ministry of Education, Wuhan University of Technology, Wuhan 430070 (China)

2010-05-01

Using asphalt pavements as a solar collector is a subject of current interest all over the world because the sun provides a cheap and abundant source of clean and renewable energy, which can be captured by black asphalt pavements. A heat-conducting device is designed to absorb energy from the sun. In order to validate what parameters are critical in the asphalt collector, a finite element model is developed to predict the thermal response of the heat-conducting device compared to the conventional asphalt mixture. Some factors that may affect the asphalt pavement collector are considered, including the coefficient of heat conductivity of the asphalt pavement, the distance between pipes with the medium, water, and the pipe's diameter. Ultimately, the finite element model can provide pavement engineers with an efficient computational tool that can be a guide to the conductive asphalt solar collector's experiment in the laboratory.

Numerical simulation on the thermal response of heat-conducting asphalt pavements

International Nuclear Information System (INIS)

Wang Hong; Wu Shaopeng; Chen Mingyu; Zhang Yuan

2010-01-01

Using asphalt pavements as a solar collector is a subject of current interest all over the world because the sun provides a cheap and abundant source of clean and renewable energy, which can be captured by black asphalt pavements. A heat-conducting device is designed to absorb energy from the sun. In order to validate what parameters are critical in the asphalt collector, a finite element model is developed to predict the thermal response of the heat-conducting device compared to the conventional asphalt mixture. Some factors that may affect the asphalt pavement collector are considered, including the coefficient of heat conductivity of the asphalt pavement, the distance between pipes with the medium, water, and the pipe's diameter. Ultimately, the finite element model can provide pavement engineers with an efficient computational tool that can be a guide to the conductive asphalt solar collector's experiment in the laboratory.

Comparison of winter temperature profiles in asphalt and concrete pavements.

Science.gov (United States)

2014-06-01

The objectives of this research were to 1) determine which pavement type, asphalt or concrete, has : higher surface temperatures in winter and 2) compare the subsurface temperatures under asphalt and : concrete pavements to determine the pavement typ...

Thermal stability analysis under embankment with asphalt pavement and cement pavement in permafrost regions.

Science.gov (United States)

Junwei, Zhang; Jinping, Li; Xiaojuan, Quan

2013-01-01

The permafrost degradation is the fundamental cause generating embankment diseases and pavement diseases in permafrost region while the permafrost degradation is related with temperature. Based on the field monitoring results of ground temperature along G214 Highway in high temperature permafrost regions, both the ground temperatures in superficial layer and the annual average temperatures under the embankment were discussed, respectively, for concrete pavements and asphalt pavements. The maximum depth of temperature field under the embankment for concrete pavements and asphalt pavements was also studied by using the finite element method. The results of numerical analysis indicate that there were remarkable seasonal differences of the ground temperatures in superficial layer between asphalt pavement and concrete pavement. The maximum influencing depth of temperature field under the permafrost embankment for every pavement was under the depth of 8 m. The thawed cores under both embankments have close relation with the maximum thawed depth, the embankment height, and the service time. The effective measurements will be proposed to keep the thermal stabilities of highway embankment by the results.

Tire-Pavement Friction Characteristics with Elastic Properties of Asphalt Pavements

OpenAIRE

Miao Yu; Guoxiong Wu; Lingyun Kong; Yu Tang

2017-01-01

The skid-resisting performance of pavement is a critical factor in traffic safety. Recent studies primarily analyze this behavior by examining the macro or micro texture of the pavement. It is inevitable that skid-resistance declines with time because the texture of pavement deteriorates throughout its service life. The primary objective of this paper is to evaluate the use of different asphalt pavements, varying in resilience, to optimize braking performance on pavement. Based on the systema...

Fatigue Behavior of Modified Asphalt Concrete Pavement

Directory of Open Access Journals (Sweden)

saad I. Sarsam

2016-02-01

Full Text Available Fatigue cracking is the most common distress in road pavement. It is mainly due to the increase in the number of load repetition of vehicles, particularly those with high axle loads, and to the environmental conditions. In this study, four-point bending beam fatigue testing has been used for control and modified mixture under various micro strain levels of (250 μƐ, 400 μƐ, and 750 μƐ and 5HZ. The main objective of the study is to provide a comparative evaluation of pavement resistance to the phenomenon of fatigue cracking between modified asphalt concrete and conventional asphalt concrete mixes (under the influence of three percentage of Silica fumes 1%, 2%, 3% by the weight of asphalt content, and (changing in the percentage of asphalt content by (0.5% ± from the optimum. The results show that when Silica fumes content was 1%, the fatigue life increases by 17%, and it increases by 46% when Silica fumes content increases to 2%, and that fatigue life increases to 34 % when Silica fumes content increases to 3% as compared with control mixture at (250 μƐ, 20°C and optimum asphalt content. From the results above, we can conclude the optimum Silica fumes content was 2%. When the asphalt content was 4.4%, the fatigue life has increased with the use of silica fumes by (50%, when asphalt content was 5.4%, the additives had led to increasing the fatigue life by (69%, as compared with the conventional asphalt concrete pavement.

Greenhouse Gas Emissions from Asphalt Pavement Construction: A Case Study in China.

Science.gov (United States)

Ma, Feng; Sha, Aimin; Lin, Ruiyu; Huang, Yue; Wang, Chao

2016-03-22

In China, the construction of asphalt pavement has a significant impact on the environment, and energy use and greenhouse gas (GHG) emissions from asphalt pavement construction have been receiving increasing attention in recent years. At present, there is no universal criterion for the evaluation of GHG emissions in asphalt pavement construction. This paper proposes to define the system boundaries for GHG emissions from asphalt pavement by using a process-based life cycle assessment method. A method for evaluating GHG emissions from asphalt pavement construction is suggested. The paper reports a case study of GHG emissions from a typical asphalt pavement construction project in China. The results show that the greenhouse gas emissions from the mixture mixing phase are the highest, and account for about 54% of the total amount. The second highest GHG emission phase is the production of raw materials. For GHG emissions of cement stabilized base/subbase, the production of raw materials emits the most, about 98%. The GHG emission for cement production alone is about 92%. The results indicate that any measures to reduce GHG emissions from asphalt pavement construction should be focused on the raw materials manufacturing stage. If the raw materials production phase is excluded, the measures to reduce GHG emissions should be aimed at the mixture mixing phase.

Optical microtopographic inspection of asphalt pavement surfaces

Science.gov (United States)

Costa, Manuel F. M.; Freitas, E. F.; Torres, H.; Cerezo, V.

2017-08-01

Microtopographic and rugometric characterization of surfaces is routinely and effectively performed non-invasively by a number of different optical methods. Rough surfaces are also inspected using optical profilometers and microtopographer. The characterization of road asphalt pavement surfaces produced in different ways and compositions is fundamental for economical and safety reasons. Having complex structures, including topographically with different ranges of form error and roughness, the inspection of asphalt pavement surfaces is difficult to perform non-invasively. In this communication we will report on the optical non-contact rugometric characterization of the surface of different types of road pavements performed at the Microtopography Laboratory of the Physics Department of the University of Minho.

Decision of National and Provincial Highway Asphalt Pavement Structure Based on Value Engineering

Directory of Open Access Journals (Sweden)

Yingwei Ren

2014-01-01

Full Text Available It is important that decision of asphalt pavement structure requires overall considerations of the performance and financial investment. To have asphalt pavement structure fulfilling good reliability, the asphalt pavement structure decision was researched based on value engineering theory. According to the national and provincial highway investigation data in Shandong Province during the last decade, the asphalt pavement performance attenuation rules of traffic levels and asphalt layer thicknesses were developed, and then the road performance evaluation method was presented. In addition, the initial investments, the costs of road maintenance, and middle-scale repair in a period were analyzed. For the light traffic and medium traffic example, using the value engineering method, the pavement performance and costs of which thickness varies from 6 cm to 10 cm were calculated and compared. It was concluded that value engineering was an effective method in deciding the asphalt pavement structure.

Basic Performance of Fibre Reinforced Asphalt Concrete with Reclaimed Asphalt Pavement Produced In Low Temperatures with Foamed Bitumen

Science.gov (United States)

Chomicz-Kowalska, Anna; Iwański, Mateusz M.; Mrugała, Justyna

2017-10-01

During the reconstruction of road pavements, the reclaimed asphalt pavement (RAP), which is obtained through milling of the worn out existing asphalt, is commonly used for producing new base courses in cold recycling processes. Two of these techniques are most popular: one using mineral-cement-emulsion mixes and one utilizing mineral cement mixes with foamed bitumen. Additionally, some amounts of RAP can be incorporated into traditional hot mix asphalt. The demand for energy efficient and environmentally friendly solutions however, results in a need for development of new techniques that would result in cheaper and more reliable solutions with smaller carbon footprint. The reduction of processing temperatures with simultaneous incorporation of reclaimed material is the most efficient way of obtaining these objectives, but it often results in the overall decrease of bituminous mix quality. The paper presents the possibility of using RAP for producing asphalt concrete in warm mix asphalt (WMA) production process by the use of foamed bitumen modified with Fischer-Tropsch synthetic wax and polymer-basalt fibers. Additionally, a series of reference mixtures were produced to investigate the effects of the additives and of the warm process. The carried out analyses and tests shown that the experimental warm mix asphalt produced with RAP and foamed bitumen returned satisfactory performance. The introduction of synthetic F-T wax in the warm foam bitumen mixes resulted in a significantly improved compaction levels and moisture and frost resistance and the addition of polymer-basalt fibers has further improved the permanent deformation resistance of the mixes. All of the designed and tested mixes have fulfilled the requirements for binding course asphalt concrete with medium traffic loads.

Effect of crumb rubber gradation on a rubberized cold recycled mixture for road pavements

DEFF Research Database (Denmark)

Pettinari, Matteo; Simone, Andrea

2015-01-01

Cold recycling technique represents the most environmental friendly solution for pavement rehabilitation nowadays. In fact, this technique allows the use of the highest percentage of reclaimed asphalt avoiding the energy consumption related to aggregates heating required by the traditional hot mix...

State of the art: Asphalt for airport pavement surfacing

Directory of Open Access Journals (Sweden)

Greg White

2018-01-01

Full Text Available Airport runways and taxiways are commonly comprised of a flexible pavement with an asphalt surface. Marshall-designed asphalt with sawn grooves is the most frequent airport asphalt surface material. However, some airports have adopted alternate asphalt mixtures for improved resistance to shear stress and for increased surface texture, allowing grooving to be avoided. Of the alternate asphalt mixtures, stone mastic asphalt is the most commonly reported. Resistance to shear stress is a critical performance requirement for airport surface asphalt. Shear stress resistance minimises the risk of rutting, shoving and groove closure. However, fracture resistance must not be ignored when developing even more shear resistance asphalt mixtures. Significant distress in airport asphalt surfaces, compliant with the traditional prescriptive specification, has increased interest in a performance-based airport asphalt specification. Commonly reported distresses include groove closure in slow moving aircraft areas and shearing in heavy aircraft braking zones. Development of reliable performance-indicative test methods is expected in the future and will enable warranted performance-based asphalt mixture design for airport surfaces. Keywords: Airport, Pavement, Asphalt, Surface

Assessment of asphalt concrete reinforcement grid in flexible pavements : final report.

Science.gov (United States)

2016-05-01

This report investigated the application of accepted methods of pavement structural evaluation to independently assess the potential structural benefit of asphalt geogrid reinforcement of an operational flexible highway pavement. The asphalt interlay...

Utilizing Lab Tests to Predict Asphalt Concrete Overlay Performance

Science.gov (United States)

2017-12-01

A series of five experimental projects and three demonstration projects were constructed to better understand the performance of pavement overlays using various levels of asphalt binder replacement (ABR) from reclaimed asphalt pavement (RAP), recycle...

Feasibility of reclaimed asphalt pavement as aggregate in portland cement concrete pavements.

Science.gov (United States)

2013-11-01

This research effort was focused on evaluating the feasibility of using minimally processed reclaimed : asphalt pavement (RAP) as aggregate replacement in concrete pavements. This research demonstrated : that concretes with up to 50 percent of the fi...

How to transform an asphalt concrete pavement into a solar turbine

International Nuclear Information System (INIS)

García, Alvaro; Partl, Manfred N.

2014-01-01

Highlights: • We create a system for harvesting energy from asphalt concrete. • We create an artificial porosity in the asphalt concrete. • We connect a chimney to this porosity. • Differences in temperature produce an air flow. • This air flow serves also for cooling down the pavement. - Abstract: Asphalt concrete can absorb a considerable amount of the incident solar radiation. For this reason asphalt roads could be used as solar collectors. There have been different attempts to achieve this goal. All of them have been done by integrating pipes conducting liquid, through the structure of the asphalt concrete. The problem of this system is that all pipes need to be interconnected: if one is broken, the liquid will come out and damage the asphalt concrete. To overcome these limitations, in this article, an alternative concept is proposed:parallel air conduits, where air can circulate will be integrated in the pavement structure. The idea is to connect these artificial pore volumes in the pavement to an updraft or to a downdraft chimney. Differences of temperature between the pavement and the environment can be used to create an air flow, which would allow wind turbines to produce an amount of energy and that would cool the pavement down in summer or even warm it up in winter. To demonstrate that this is possible, an asphalt concrete prototype has been created and basics calculations on the parameters affecting the system have been done. It has been found that different temperatures, volumes of air inside the asphalt and the difference of temperature between the asphalt concrete and the environment are critical to maximize the air flow through the pavement. Moreover, it has been found that this system can be also used to reduce the heat island effect

The effect of Cryogenic Crumb Rubber in cold recycled mixes for road pavements

DEFF Research Database (Denmark)

Pettinari, Matteo; Dondi, Giulio; Sangiorgi, Cesare

2014-01-01

of cold recycled mixes for road bases is considerable. Furthermore, new products are continuously being introduced or developed for recycling purposes. The objective of this research project was to test the effects, both mechanically and environmentally, of crumb rubber included in 100% Reclaimed Asphalt......Over recent years, the necessity of reducing the environmental mpact of building new infrastructures has increasingly directed research toward developing innovative manufacturing methods and materials that can satisfy these objectives. Cold recycling, widely used in renovating road pavements...

Investigation on performances of asphalt mixtures made with Reclaimed Asphalt Pavement: Effects of interaction between virgin and RAP bitumen

Directory of Open Access Journals (Sweden)

Luca Noferini

2017-07-01

Full Text Available According to most recent surveys, the European area produced 265 mil tonnes of asphalt for road applications in 2014. In the same year, the amount of available RAP was more than 50 mil tonnes. The use of RAP in new blended mixes reduces the need of neat bitumen, making RAP recycling economically attractive. Despite the economic and environmental benefits, road authorities tend to limit the use of RAP in asphalt mixes due to uncertainty about field performances. The present study focuses on the interaction between neat and RAP bitumen in asphalt mixes made with different RAP content. The effects of RAP on physical and rheological properties of the final bituminous blend were investigated. This study is part of a wider research, where a specific type of asphalt mixture was produced with different RAP contents being 10%, 20% and 30% by mass of the mix. Bitumen was extracted and recovered from asphalt mixes, then it was subjected to the following laboratory tests: standard characterization, dynamic viscosity and rheological analysis with DSR. Findings showed that the effects of RAP bitumen on the final blend varied in proportion to RAP content. A threshold value of RAP content was found, below which bitumen was not subjected to significant changes in physical and rheological properties. Practical implications on production methods and paving of RAP mixes are also proposed. Keywords: Reclaimed Asphalt Pavement (RAP, Recycling, Bitumen blending, Bitumen rheology

Research on the characteristics of temperature field of asphalt pavement in seasonal frozen region

International Nuclear Information System (INIS)

Qiao, Jiangang; Liu, Weizheng

2014-01-01

The characteristics of climate in seasonal frozen area are low temperature and a large range of temperature variation between day and night in winter. These characteristics often lead to problems of asphalt pavement, especially transverse cracks. To reduce the problems of asphalt pavement, it is necessary to examine the distribution of the temperature range of asphalt pavement. A three-dimensional finite element model was used, taking the SMA asphalt pavement as an example with solid70 and plane55 unit features of ANSYS software. It can obtain the relationship between temperature gradient and time and the relationship between temperature gradient and depth. In addition, a function relation model of stress and time was also established. It can provide a theoretical basis for the prevention and treatment of problems of asphalt pavement in seasonal frozen area. Moreover, it has an important significance for improving asphalt pavement design

Long-term aging of recycled binders : [summary].

Science.gov (United States)

2015-10-01

At 80 million tons a year representing more than 80% of all milled asphalt pavement : asphalt paving is Americas most recycled material. Asphalt can be recycled in place, which is : very cost effective; however, aging of recycled binder ca...

Determination of usable residual asphalt binder in RAP.

Science.gov (United States)

2009-01-01

For current recycled mix designs, the Illinois Department of Transportation (IDOT) assumes 100% contribution of : working binder from Recycled Asphalt Pavement (RAP) materials when added to Hot Mix Asphalt (HMA). However, it is : unclear if this assu...

Effect of interlayer bonding quality of asphalt layers on pavement performance

Science.gov (United States)

Jaskula, Piotr; Rys, Dawid

2017-09-01

The quality of interlayer bonding at the interfaces between the asphalt layers in flexible pavements affects the overall pavement performance. Lack or partial lack of interlayer bonding between asphalt layers can cause pavement’s premature failures such as rutting, slippage of the wearing course, cracking or simply a reduction in the calculated fatigue life of the pavement structure. This paper shows the case studies of investigation of actual or potential premature failure of newly reconstructed and constructed pavements where low quality of interlayer bonding has a dominant meaning. In situ and laboratory tests were performed and followed by analytical calculation of pavement structure where thicknesses of layers and maximum shear strengths obtained from the tests were used. During the investigation it was found out that a low quality of tack coat as well as the same aggregate gradation in the bonded asphalt mixtures were the main reasons behind the weak quality of interlayer bonding. Partial interlayer bonding has a strong influence on reduction of calculated fatigue life of pavement. The summary of the paper includes recommendations on how to avoid the low quality of interlayer bonding of asphalt layers.

Design and verification of bituminous mixtures with the increased content of reclaimed asphalt pavement

Science.gov (United States)

Bańkowski, Wojciech; Król, Jan; Gałązka, Karol; Liphardt, Adam; Horodecka, Renata

2018-05-01

Recycling of bituminous pavements is an issue increasingly being discussed in Poland. The analysis of domestic and foreign experience indicates a need to develop this technology in our country, in particular the hot feeding and production technologies. Various steps are being taken in this direction, including research projects. One of them is the InnGA project entitled: “Reclaimed asphalt pavement: Innovative technology of bituminous mixtures using material from reclaimed asphalt pavement”. The paper presents the results of research involving the design of bituminous mixtures in accordance with the required properties and in excess of the content of reclaimed asphalt permitted by the technical guidelines. It presents selected bituminous mixtures with the content of RAP of up to 50% and the results of tests from verification of industrial production of those mixtures. The article discusses the details of the design process of mixtures with a high content of reclaimed asphalt, the carried out production tests and discusses the results of tests under the verification of industrial production. Testing included basic tests according to the Polish technical requirements of WT- 2 and the extended functional testing. The conducted tests and analyses helped to determine the usefulness of the developed bituminous mixtures for use in experimental sections and confirmed the possibility of using an increased amount of reclaimed asphalt up to 50% in mixtures intended for construction of national roads.

Effects of reclaimed asphalt pavement on indirect tensile strength test of foamed asphalt mix tested in dry condition

International Nuclear Information System (INIS)

Katman, Herda Yati; Norhisham, Shuhairy; Ismail, Norlela; Ibrahim, Mohd Rasdan; Matori, Mohd Yazip

2013-01-01

Indirect tensile strength (ITS) test was conducted to analyse strength of the foamed asphalt mixes incorporating reclaimed asphalt pavement. Samples were tested for ITS after cured in the oven at 40°C for 72 hours. This testing condition known as dry condition or unconditioned. Laboratory results show that reclaimed asphalt pavement (RAP) contents insignificantly affect the ITS results. ITS results significantly affected by foamed bitumen contents.

Application of Conductive Materials to Asphalt Pavement

Directory of Open Access Journals (Sweden)

Hai Viet Vo

2017-01-01

Full Text Available Snow-melting pavement technique is an advanced preservation method, which can prevent the forming of snow or ice on the pavement surface by increasing the temperature using an embedded heating system. The main scope of this study is to evaluate the impact of conductive additives on the heating efficiency. The electrical resistivity and thermal conductivity were considered to investigate effects of conductive additives, graphite, and carbon fibers on the snow-melting ability of asphalt mixtures. Also, the distribution of the conductive additives within the asphalt concrete body was investigated by microstructural imaging. An actual test was applied to simulate realistic heating for an asphalt concrete mixture. Thermal testing indicated that graphite and carbon fibers improve the snow-melting ability of asphalt mixes and their combination is more effective than when used alone. As observed in the microstructural image, carbon fibers show a long-range connecting effect among graphite conductive clusters and gather in bundles when added excessively. According to the actual test, adding the conductive additives helps improve snow-melting efficiency by shortening processing time and raising the surface temperature.

Laboratory Measurements of Particulate Matter Concentrations from Asphalt Pavement Abrasion

Directory of Open Access Journals (Sweden)

Fullová Daša

2016-12-01

Full Text Available The issue of emissions from road traffic is compounded by the fact that the number of vehicles and driven kilometres increase each year. Road traffic is one of the main sources of particulate matter and traffic volume is still increasing and has unpleasant impact on longevity of the pavements and the environment. Vehicle motions cause mechanical wearing of the asphalt pavement surface - wearing course by vehicle tyres. The contribution deals with abrasion of bituminous wearing courses of pavements. The asphalt mixtures of wearing courses are compared in terms of mechanically separated particulate matter. The samples of asphalt mixtures were rutted in wheel tracking machine. The particulate matter measurements were performed in laboratory conditions. The experimental laboratory measurements make it possible to sample particulates without contamination from exhaust emissions, abraded particles from vehicles, resuspension of road dust and climate affects. The contribution offers partial results of measurements on six trial samples of asphalt mixtures with different composition. It presents particulate matter morphology and the comparison of rutted asphalt samples in terms of PM mass concentrations and chemical composition.

Assessment of low temperature cracking in asphalt pavement mixes and rheological performance of asphalt binders

Science.gov (United States)

Sowah-Kuma, David

Government spends a lot of money on the reconstruction and rehabilitation of road pavements in any given year due to various distresses and eventual failure. Low temperature (thermal) cracking, one of the main types of pavement distress, contributes partly to this economic loss, and comes about as a result of accumulated tensile strains exceeding the threshold tensile strain capacity of the pavement. This pavement distress leads to a drastic reduction of the pavement's service life and performance. In this study, the severity of low temperature (thermal) cracking on road pavements selected across the Province of Ontario and its predicted time to failure was assessed using the AASTHO Mechanistic-Empirical Pavement Design Guide (MEPDG) and AASHTOWARE(TM) software, with inputs such as creep compliance and tensile strength from laboratory test. Highway 400, K1, K2, Y1, Sasobit, Rediset LQ, and Rediset WMX were predicted to have a pavement in-service life above 15 years. Additionally, the rheological performance of the recovered asphalt binders was assessed using Superpave(TM) tests such as the dynamic shear rheometer (DSR) and bending beam rheometer (BBR). Further tests using modified standard protocols such as the extended bending beam rheometer (eBBR) (LS-308) test method and double-edge notched tension (DENT) test (LS-299) were employed to evaluate the failure properties associated with in service performance. The various rheological tests showed K1 to be the least susceptible to low temperature cracking compared to the remaining samples whiles Highway 24 will be highly susceptible to low temperature cracking. X-ray fluorescence (XRF) analysis was performed on the recovered asphalt binders to determine the presence of metals such as zinc (Zn) and molybdenum (Mo) believed to originate from waste engine oil, which is often added to asphalt binders. Finally, the severity of oxidative aging (hardening) of the recovered asphalt binders was also evaluated using the

The Rejuvenating Effect in Hot Asphalt Recycling by Mortar Transfer Ratio and Image Analysis.

Science.gov (United States)

Wang, Fusong; Wang, Zipeng; Li, Chao; Xiao, Yue; Wu, Shaopeng; Pan, Pan

2017-05-24

Using a rejuvenator to improve the performance of asphalt pavement is an effective and economic way of hot asphalt recycling. This research analyzes the rejuvenating effect on aged asphalt by means of a Mortar Transfer Ratio (MTR) test, which concerns the ratio of asphalt mortar that moves from recycled aggregates (RAP aggregates) to fresh added aggregates when aged asphalt is treated with a regenerating agent and comes into contact with fresh aggregates. The proposed MTR test analyzes the regeneration in terms of the softening degree on aged asphalt when the rejuvenator is applied. The covered area ratio is studied with an image analyzing tool to understand the possibility of mortar transferring from RAP aggregates to fresh aggregates. Additionally, a micro-crack closure test is conducted and observed through a microscope. The repairing ability and diffusion characteristics of micro-cracks can therefore be analyzed. The test results demonstrate that the proposed mortar transfer ratio is a feasible way to evaluate rejuvenator diffusion during hot recycling. The mortar transfer ratio and uncovered area ratio on fresh aggregates are compatible, and can be used to quantify the contribution of the rejuvenator. Within a certain temperature range, the diffusing effect of the rejuvenator is better when the diffusing temperature is higher. The diffusion time of the rejuvenator is optimum when diffusion occurs for 4-8 h. When the rejuvenator is properly applied, the rough and cracking surface can be repaired, resulting in better covered aggregates. The micro-closure analysis visually indicates that rejuvenators can be used to repair the RAP aggregates during hot recycling.

Design and evaluation of foamed asphalt base materials.

Science.gov (United States)

2013-05-01

Foamed asphalt stabilized base (FASB) combines reclaimed asphalt pavement (RAP), recycled : concrete (RC), and/or graded aggregate base (GAB) with a foamed asphalt binder to produce a : partially stabilized base material. The objectives of this study...

Asphalt Pavement Aging and Temperature Dependent Properties Using Functionally Graded Viscoelastic Model

Science.gov (United States)

Dave, Eshan V.

2009-01-01

Asphalt concrete pavements are inherently graded viscoelastic structures. Oxidative aging of asphalt binder and temperature cycling due to climatic conditions being the major cause of non-homogeneity. Current pavement analysis and simulation procedures dwell on the use of layered approach to account for these non-homogeneities. The conventional…

Residual Fatigue Properties of Asphalt Pavement after Long-Term Field Service

Directory of Open Access Journals (Sweden)

Peide Cui

2018-05-01

Full Text Available Asphalt pavement is widely used for expressways due to its advantages of flexibility, low cost, and easy maintenance. However, pavement failures, including cracking, raveling, and potholes, will appear after long-term service. This research evaluated the residual fatigue properties of asphalt pavement after long-term field service. Fatigue behavior of specimens with different pavement failure types, traffic load, service time, and layers were collected and characterized. Results indicate that after long-term field service, surface layer has a longer fatigue life under small stress levels, but shorter fatigue life under large stress levels. Longer service time results in greater sensitivity to loading stress, while heavier traffic results in shorter fatigue life. Surface and underneath layers present very close fatigue trend lines in some areas, indicating that the fatigue behavior of asphalt mixture in surface and underneath layers are aged to the same extent after eight to ten years of field service.

Oriented heat release in asphalt pavement induced by high-thermal-conductivity rods

International Nuclear Information System (INIS)

Du, Yinfei; Wang, Shengyue

2015-01-01

In this paper, a new principle of using aligned high-thermal-conductivity rods to enhance the oriented heat conduction in asphalt pavement was proposed. The results showed that the designed structure absorbed more heat during the day. The heat flow in the designed structure presented a non-uniform horizontal distribution. At the depth of 4 cm, the horizontal and vertical heat fluxes through steel rods were thirteen and ten times higher than those through asphalt mixture, respectively. The maximum temperature of the designed structure reduced by 3.6 °C–6.5 °C at the depth of 4 cm. The results of indoor irradiation test showed a trend consistent with those of numerical simulation. After 500 thousand times of standard axis load were applied, the rutting depth of the designed structure reduced by 43.4%. The principle proposed is expected to be used to induce an oriented heat release accumulated in asphalt pavement and reduce pavement temperature and rutting. - Highlights: • Steel rods were inserted in the middle and bottom layers to build thermal channels. • Steel rods absorbed heat from asphalt mixture and rapidly released them to subgrade. • The heat flux through asphalt mixture decreased and pavement temperature reduced.

Leaching of organic contaminants from storage of reclaimed asphalt pavement.

Science.gov (United States)

Norin, Malin; Strömvall, A M

2004-03-01

Recycling of asphalt has been promoted by rapid increases in both the use and price of petroleum-based bitumen. Semi-volatile organic compounds in leachates from reclaimed asphalt pavement, measured in field samples and in laboratory column test, were analysed through a GC/MS screen-test methodology. Sixteen PAH (polyaromatic hydrocarbons) were also analysed in leachates from the column study. The highest concentrations of semi-volatile compounds, approximately 400 microg l(-1), were measured in field samples from the scarified stockpile. Naphthalene, butylated hydroxytoluene (BHT) and dibutyl phthalate (DBP) were the most dominant of the identified semi-volatiles. The occurrence of these compounds in urban groundwater, also indicate high emission rates and persistent structures of the compounds, making them potentially hazardous. Car exhausts, rubber tires and the asphalt material itself are all probable emission sources, determined from the organic contaminants released from the stockpiles. The major leaching mechanism indicated was dissolution of organic contaminants from the surface of the asphalt gravels. In the laboratory column test, the release of high-molecular weight and more toxic PAH was higher in the leachates after two years than at the commencement of storage. The concentrations of semi-volatiles in leachates, were also several times lower than those from the field stockpile. These results demonstrate the need to follow up laboratory column test with real field measurements.

Feasibility of reclaimed asphalt pavement as aggregate in portland cement concrete pavement, phase II : field demonstration.

Science.gov (United States)

2015-10-01

This research was focused on evaluating the feasibility of using minimally processed reclaimed asphalt pavement (RAP) as : aggregate replacement in concrete pavements. An initial phase of research demonstrated that concretes with up to 50 percent : o...

Density measurement verification for hot mix asphalt concrete pavement construction.

Science.gov (United States)

2010-06-01

Oregon Department of Transportation (ODOT) requires a minimum density for the construction of dense-graded hot mix asphalt concrete (HMAC) pavements to ensure the likelihood that the pavement will not experience distresses that reduce the expected se...

Density measurement verification for hot mixed asphalt concrete pavement construction.

Science.gov (United States)

2010-06-01

Oregon Department of Transportation (ODOT) requires a minimum density for the construction of dense-graded hot mix asphalt concrete (HMAC) pavements to ensure the likelihood that the pavement will not experience distresses that reduce the expected se...

Building Asphalt Pavement with SBS-based Compound Added Using a Dry Process in Greenland

DEFF Research Database (Denmark)

Lee, Hosin; Kim, Yongjoo; Geisler, Nivi

2009-01-01

PMA where it is formulated to melt and blend with asphalt quickly during a batch mixing process. The main objectives of this study are to (1) build asphalt pavement using asphalt mixtures with SBS-based compound added using a “dry” process at the batch plant and (2) evaluate its performance under......-based compound seemed to affect the asphalt mix to become more flexible under the heavy loads. By adding SBS-based compound to asphalt mixtures using a “dry” process, it is expected that the pavement would become more resistant to rutting than a typical asphalt mixture used in Greenland while enduring its arctic...

Rutting Prediction in Asphalt Pavement Based on Viscoelastic Theory

Directory of Open Access Journals (Sweden)

Nahi Mohammed Hadi

2016-01-01

Full Text Available Rutting is one of the most disturbing failures on the asphalt roads due to the interrupting it is caused to the drivers. Predicting of asphalt pavement rutting is essential tool leads to better asphalt mixture design. This work describes a method of predicting the behaviour of various asphalt pavement mixes and linking these to an accelerated performance testing. The objective of this study is to develop a finite element model based on viscoplastic theory for simulating the laboratory testing of asphalt mixes in Hamburg Wheel Rut Tester (HWRT for rutting. The creep parameters C1, C2 and C3 are developed from the triaxial repeated load creep test at 50°C and at a frequency of 1 Hz and the modulus of elasticity and Poisson’ s ratio determined at the same temperature. Viscoelastic model (creep model is adopted using a FE simulator (ANSYS in order to calculate the rutting for various mixes under a uniform loading pressure of 500 kPa. An eight-node with a three Degrees of Freedom (UX, UY, and UZ Element is used for the simulation. The creep model developed for HWRT tester was verified by comparing the predicted rut depths with the measured one and by comparing the rut depth with ABAQUS result from literature. Reasonable agreement can be obtained between the predicted rut depths and the measured one. Moreover, it is found that creep model parameter C1 and C3 have a strong relationship with rutting. It was clear that the parameter C1 strongly influences rutting than the parameter C3. Finally, it can be concluded that creep model based on finite element method can be used as an effective tool to analyse rutting of asphalt pavements.

A Review on Using Crumb Rubber in Reinforcement of Asphalt Pavement

Science.gov (United States)

Mashaan, Nuha Salim; Ali, Asim Hassan; Karim, Mohamed Rehan; Abdelaziz, Mahrez

2014-01-01

An immense problem affecting environmental pollution is the increase of waste tyre vehicles. In an attempt to decrease the magnitude of this issue, crumb rubber modifier (CRM) obtained from waste tyre rubber has gained interest in asphalt reinforcement. The use of crumb rubber in the reinforcement of asphalt is considered as a smart solution for sustainable development by reusing waste materials, and it is believed that crumb rubber modifier (CRM) could be an alternative polymer material in improving hot mix asphalt performance properties. In this paper, a critical review on the use of crumb rubber in reinforcement of asphalt pavement will be presented and discussed. It will also include a review on the effects of CRM on the stiffness, rutting, and fatigue resistance of road pavement construction. PMID:24688369

A Review on Using Crumb Rubber in Reinforcement of Asphalt Pavement

Directory of Open Access Journals (Sweden)

Nuha Salim Mashaan

2014-01-01

Full Text Available An immense problem affecting environmental pollution is the increase of waste tyre vehicles. In an attempt to decrease the magnitude of this issue, crumb rubber modifier (CRM obtained from waste tyre rubber has gained interest in asphalt reinforcement. The use of crumb rubber in the reinforcement of asphalt is considered as a smart solution for sustainable development by reusing waste materials, and it is believed that crumb rubber modifier (CRM could be an alternative polymer material in improving hot mix asphalt performance properties. In this paper, a critical review on the use of crumb rubber in reinforcement of asphalt pavement will be presented and discussed. It will also include a review on the effects of CRM on the stiffness, rutting, and fatigue resistance of road pavement construction.

Fundamental evaluation of the interaction between RAS/RAP and virgin asphalt binders.

Science.gov (United States)

2017-08-01

A comprehensive laboratory testing program was conducted in this research project to examine the blending between reclaimed asphalt pavement (RAP)/recycled asphalt shingles (RAS) and virgin asphalt binders and to evaluate the factors that may affect ...

Reinforcement of Recycled Foamed Asphalt Using Short Polypropylene Fibers

Directory of Open Access Journals (Sweden)

Yongjoo Kim

2013-01-01

Full Text Available This paper presents the reinforcing effects of the inclusion of short polypropylene fibers on recycled foamed asphalt (RFA mixture. Short polypropylene fibers of 10 mm length with a 0.15% by weight mixing ratio of the fiber to the asphalt binder were used. The Marshall stability test, the indirect tensile strength test, the resilient modulus test, and wheel tracking test of the RFA mixtures were conducted. The test results were compared to find out the reinforcing effects of the inclusion of the fiber and the other mixtures, which included the conventional recycled foamed asphalt (RFA mixtures; the cement reinforced recycled foamed asphalt (CRFA mixtures; the semihot recycled foamed asphalt (SRFA mixtures; and recycled hot-mix asphalt (RHMA mixtures. It is found that the FRFA mixture shows higher Marshall stability than the RFA and SRFA mixtures, higher indirect tensile strength than the RFA mixture, and higher rut resistance than the RFA, SRFA, and RHMA mixtures as seen from the wheel tracking test.

Development of high stability hot mix asphalt concrete with hybrid binder

Directory of Open Access Journals (Sweden)

Toshiaki Hirato

2014-12-01

Full Text Available Cost reduction of public works projects has been desired due to severe financial circumstances. Therefore, asphalt pavement has been requested to extend its life. Semi-flexible pavement or epoxy asphalt pavement, which has high rutting resistance and oil resistance, may be applied to the place where these performances ae demanded. However, special technique is required in manufacturing and construction. In addition, these materials have also raised a problem that they cannot be recycled. Meanwhile, conventional asphalt pavement has several drawbacks. It is vulnerable to rutting caused by traffic load and damage caused by petroleum oils such as gasoline or motor oil. The materials used in asphalt mixtures were studied for improving the durability of asphalt mixture. A high stability asphalt concrete was developed which has equal or superior performance to semi-flexible pavement and epoxy asphalt pavement. In this paper, the process of selecting the substance and the characteristics evaluation of the developed mixtures ae described. Furthermore, an inspection result as well as follow-up survey of the performance of the developed mixtures obtained from trial and actual construction is shown.

Aggregate Toughness/Abrasion Resistance and Durability/Soundness Tests Related to Asphalt Concrete Performance in Pavements

Science.gov (United States)

1998-03-01

The properties of aggregates used in asphalt concretes are very important to the performance of the pavements in which the asphalt concretes are used. Often pavement distress, such as stripping and rutting, can be traced directly to the aggregates us...

Representative volume element of asphalt pavement for electromagnetic measurements

Directory of Open Access Journals (Sweden)

Terhi Pellinen

2015-02-01

Full Text Available The motivation for this study was to investigate the representative volume element (RVE needed to correlate the nondestructive electromagnetic (EM measurements with the conventional destructive asphalt pavement quality control measurements. A large pavement rehabilitation contract was used as the test site for the experiment. Pavement cores were drilled from the same locations where the stationary and continuous Ground Penetrating Radar (GPR measurements were obtained. Laboratory measurements included testing the bulk density of cores using two methods, the surface-saturated dry method and determining bulk density by dimensions. Also, Vector Network Analyzer (VNA and the through specimen transmission configuration were employed at microwave frequencies to measure the reference dielectric constant of cores using two different footprint areas and therefore volume elements. The RVE for EM measurements turns out to be frequency dependent; therefore in addition to being dependent on asphalt mixture type and method of obtaining bulk density, it is dependent on the resolution of the EM method used. Then, although the average bulk property results agreed with theoretical formulations of higher core air void content giving a lower dielectric constant, for the individual cores there was no correlation for the VNA measurements because the volume element seizes deviated. Similarly, GPR technique was unable to capture the spatial variation of pavement air voids measured from the 150-mm drill cores. More research is needed to determine the usable RVE for asphalt.

Field Control and Performance of Asphalt Mixtures Containing Greater than 25 Percent Reclaimed Asphalt Pavement : Draft Final Report

Science.gov (United States)

2018-02-02

The Alabama Department of Transportation (ALDOT) and other highway agencies are interested in utilization of higher percentages of reclaimed asphalt pavement (RAP) in asphalt mixtures. There are a number of research studies at both state and national...

Investigation of the Asphalt Pavement Analyzer (APA) testing program in Nebraska.

Science.gov (United States)

2008-03-01

The asphalt pavement analyzer (APA) has been widely used to evaluate hot-mix asphalt (HMA) rutting potential in mix : design and quality control-quality assurance (QC-QA) applications, because the APA testing and its data analyses are : relatively si...

Thermal behavior of an asphalt pavement in the laboratory and in the parking lot.

Science.gov (United States)

Martinkauppi, J B; Mäkiranta, A; Kiijärvi, J; Hiltunen, E

2015-01-01

The urban, constructed areas are full of buildings and different kinds of pavements and have a noticeable lack of trees and flora. These areas are accumulating the heat from the Sun, people, vehicles, and constructions. One interesting heat collector is the asphalt pavement. How does the heat transfer to different layers under the pavement or does it? What are the temperatures under the pavement in Finland where the winter can be pretty hard? How can those temperatures be measured accurately? These are the main questions this paper gives the preliminary answers to. First the thermal behavior of asphalt and the layers beneath are researched in the laboratory and then the measurement field is bored and dug in the parking in the Western coast of Finland, 63°5'45'' N. Distributed temperature sensing method was found to be a good choice for temperature measurements. Thermal behavior of pavement has been monitored in different layers and the preliminary results have been published here. The goal of this research is to assess the applicability of asphalt pavements for heat energy collection.

Investigation of Self Consolidating Concrete Containing High Volume of Supplementary Cementitious Materials and Recycled Asphalt Pavement Aggregates

Science.gov (United States)

Patibandla, Varun chowdary

The use of sustainable technologies such as supplementary cementitiuous materials (SCMs), and/or recycled materials is expected to positively affect the performance of concrete mixtures. However, it is important to study and qualify such mixtures and check if the required specifications of their intended application are met before they can be implemented in practice. This study presents the results of a laboratory investigation of Self Consolidating concrete (SCC) containing sustainable technologies. A total of twelve concrete mixtures were prepared with various combinations of fly ash, slag, and recycled asphalt pavement (RAP). The mixtures were divided into three groups with constant water to cementitiuous materials ratio of 0.37, and based on the RAP content; 0, 25, and 50% of coarse aggregate replaced by RAP. All mixtures were prepared to achieve a target slump flow equal to or higher than 500 mm (24in). A control mixture for each group was prepared with 100% Portland cement whereas all other mixtures were designed to have up to 70% of portland cement replaced by a combination of supplementary cementitiuous materials (SCMs) such as class C fly ash and granulated blast furnace slag. The properties of fresh concrete investigated in this study include flowability, deformability; filling capacity, and resistance to segregation. In addition, the compressive strength at 3, 14, and 28 days, the tensile strength, and the unrestrained shrinkage up to 80 days was also investigated. As expected the inclusion of the sustainable technologies affected both fresh and hardened concrete properties. Analysis of the experimental data indicated that inclusion of RAP not only reduces the ultimate strength, but it also affected the compressive strength development rate. Moreover, several mixes satisfied compressive strength requirements for pavements and bridges; those mixes included relatively high percentages of SCMs and RAP. Based on the results obtained in this study, it is not

Determination of the most favorable experimental conditions for obtaining asphalt emulsions modified with discarded polymers in the reconstruction of pavements

International Nuclear Information System (INIS)

Coward Ugalde, Hector Arturo

2014-01-01

The most favorable experimental conditions are determined for the production of asphalt emulsions modified with tire scrap rubber, petroleum material and recycled asphalt in the reconstruction of flexible pavements in a slow breaking process. Asphalt emulsions are made with 65% V/V of fluidized asphalt at different conditions of operation and composition of soap solution. The equipment of a centrifugal pump and a colloidal mill are used. Two different compositions are employed to make soap solutions. The best conditions to prepare the asphalt emulsions in the pilot plant have been: a stirring speed of 2100 rpm in the centrifugal pump and a speed of 3300 rpm of the colloidal mill. Asphaltic grouts made with asphalt emulsion modified to 1% m/m of rubber have shown the best coverage in the stripping test, evidencing little asphalt release, high adhesion of the asphalt on the aggregate and good stability. Asphalt emulsions with rubber are recommended with a granulometry that passes the No. 200 mesh for rubber and use the indicated equipment to carry out the process of asphalt modification to obtain better results in the performance of asphalt emulsion [es

Hot Mix Asphalt Recycling : Practices and Principles

NARCIS (Netherlands)

Mohajeri, M.

2015-01-01

Hot mix asphalt recycling has become common practice all over the world since the 1970s because of the crisis in oil prices. In the Netherlands, hot recycling has advanced to such an extent that in most of the mixtures more than 50% of reclaimed asphalt (RA) is allowed. These mixtures with such a

Evaluation of recycled asphaltic concrete : final report.

Science.gov (United States)

1977-01-01

This report describes a project in which approximately 6,200 tons (5,630 Mg) of asphaltic concrete were recycled through a conventional asphalt batch plant. During the construction of the project, a buildup of asphalt-coated fines occurred in the dry...

Rutting Performance of Cold-Applied Asphalt Repair Materials for Airfield Pavements

Science.gov (United States)

2017-06-23

this study. Cold mix asphalt materials, further denoted cold mixes , were selected to reasonably represent available products on the market and were...pavement repair, primarily because of the small quantities involved and/or the unavailability of hot- mixed asphalt. These cold-applied mixtures have...poorer rutting resistance than hot mix asphalt because additives, often solvent, are required to provide adequate workability for them to be placed

Performance of Recycled Porous Hot Mix Asphalt with Gilsonite Additive

Directory of Open Access Journals (Sweden)

Ludfi Djakfar

2015-01-01

Full Text Available The objective of the study is to evaluate the performance of porous asphalt using waste recycled concrete material and explore the effect of adding Gilsonite to the mixture. As many as 90 Marshall specimens were prepared with varied asphalt content, percentage of Gilsonite as an additive, and proportioned recycled and virgin coarse aggregate. The test includes permeability capability and Marshall characteristics. The results showed that recycled concrete materials seem to have a potential use as aggregate in the hot mix asphalt, particularly on porous hot mix asphalt. Adding Gilsonite at ranges 8–10% improves the Marshall characteristic of the mix, particularly its stability, without decreasing significantly the permeability capability of the mix. The use of recycled materials tends to increase the asphalt content of the mix at about 1 to 2% higher. With stability reaching 750 kg, the hot mix recycled porous asphalt may be suitable for use in the local roads with medium vehicle load.

Thermal Behavior of an Asphalt Pavement in the Laboratory and in the Parking Lot

Directory of Open Access Journals (Sweden)

J. B. Martinkauppi

2015-01-01

Full Text Available The urban, constructed areas are full of buildings and different kinds of pavements and have a noticeable lack of trees and flora. These areas are accumulating the heat from the Sun, people, vehicles, and constructions. One interesting heat collector is the asphalt pavement. How does the heat transfer to different layers under the pavement or does it? What are the temperatures under the pavement in Finland where the winter can be pretty hard? How can those temperatures be measured accurately? These are the main questions this paper gives the preliminary answers to. First the thermal behavior of asphalt and the layers beneath are researched in the laboratory and then the measurement field is bored and dug in the parking in the Western coast of Finland, 63°5′45′′ N. Distributed temperature sensing method was found to be a good choice for temperature measurements. Thermal behavior of pavement has been monitored in different layers and the preliminary results have been published here. The goal of this research is to assess the applicability of asphalt pavements for heat energy collection.

Fatigue Evaluation of Recycled Asphalt Mixture Based on Energy-Controlled Mode

Directory of Open Access Journals (Sweden)

Tao Ma

2017-01-01

Full Text Available The fatigue properties of asphalt mixtures are important inputs for mechanistic-empirical pavement design. To understand the fatigue properties of asphalt mixtures better and to predict the fatigue life of asphalt mixtures more precisely, the energy-controlled test mode was introduced. Based on the implementation theory, the laboratory practice for the energy-controlled mode was realized using a four-point-bending fatigue test with multiple-step loading. In this mode, the fatigue performance of typical AC-20 asphalt specimens with various reclaimed asphalt pavement (RAP contents was tested and evaluated. Results show that the variation regulation of the dissipated energy and accumulative energy is compatible with the loading control principle, which proves the feasibility of the method. In addition, the fatigue life of the asphalt mixture in the energy-controlled mode was between that for the stress-controlled and strain-controlled modes. The specimen with a higher RAP content has a longer fatigue life and better fatigue performance.

Numerical Study of Tire Hydroplaning Based on Power Spectrum of Asphalt Pavement and Kinetic Friction Coefficient

Directory of Open Access Journals (Sweden)

Shengze Zhu

2017-01-01

Full Text Available Hydroplaning is a driving phenomenon threating vehicle’s control stability and safety. It happens when tire rolls on wet pavement with high speed that hydrodynamic force uplifts the tire. Accurate numerical simulation to reveal the mechanism of hydroplaning and evaluate the function of relevant factors in this process is significant. In order to describe the friction behaviors of tire-pavement interaction, kinetic friction coefficient curve of tire rubber and asphalt pavement was obtained by combining pavement surface power spectrum and complex modulus of tread rubber through Persson’s friction theory. Finite element model of tire-fluid-pavement was established in ABAQUS, which was composed of a 225-40-R18 radial tire and three types of asphalt pavement covered with water film. Mechanical responses and physical behaviors of tire-pavement interaction were observed and compared with NASA equation to validate the applicability and accuracy of this model. Then contact force at tire-pavement interface and critical hydroplaning speed influenced by tire inflation pressure, water film thickness, and pavement types were investigated. The results show higher tire inflation pressure, thinner water film, and more abundant macrotexture enhancing hydroplaning speed. The results could be applied to predict hydroplaning speed on different asphalt pavement and improve pavement skid resistance design.

Study of lime vs. no lime in cold in-place recycled asphalt concrete pavements : final report.

Science.gov (United States)

1991-09-01

The resilient characteristics of cold in-place recycled asphalt concrete with and without lime were examined. Six core samples were obtained from a site two months after construction; six months later, six additional core samples were obtained from t...

Hot Mix Asphalt Recycling: Practices and Principles

OpenAIRE

Mohajeri, M.

2015-01-01

Hot mix asphalt recycling has become common practice all over the world since the 1970s because of the crisis in oil prices. In the Netherlands, hot recycling has advanced to such an extent that in most of the mixtures more than 50% of reclaimed asphalt (RA) is allowed. These mixtures with such a high RA content are produced in a batch plant to which a parallel drum is attached. In this drum RA is pre-heated to approximately 130°C. Since 2007 another hot mix recycling techniques became availa...

Cooling permafrost embankment by enhancing oriented heat conduction in asphalt pavement

International Nuclear Information System (INIS)

Yinfei, Du; Shengyue, Wang; Shuangjie, Wang; Jianbing, Chen

2016-01-01

Highlights: • Solar radiation heat was prevented from entering the embankment in summer. • The downward heat transfer efficiency in asphalt pavement and embankment reduced. • The net heat accumulation in the embankment decreased. - Abstract: In this paper, a new method was proposed to decrease the heat accumulation in permafrost embankment by controlling an oriented heat transfer in asphalt pavement. Two highly oriented heat-induced structures, named G-OHIS (only gradient thermal conductivity) and G+R-OHIS (combined gradient thermal conductivity and heat reflective layer), were designed by using two indexes of summertime daily heat absorption and annual net heat accumulation on the top of embankment. The results showed that the heat absorptions on the top of embankments of the G-OHIS and G+R-OHIS in summer decreased by 9.9% and 23.2% respectively. The annual net heat accumulation on the top of embankment decreased by 6.2% for the G-OHIS and 37.9% for the G+R-OHIS. Moreover, the summertime mean daily temperatures on the top of embankments of the G-OHIS and G+R-OHIS reduced by 0.74 °C and 1.66 °C respectively. The annual temperature difference on the top of embankment reduced by 1.07 °C for the G-OHIS and 1.96 °C for the G+R-OHIS. The effectiveness of the G-OHIS in reducing pavement temperature was validated by an indoor irradiation test. It is expected to reduce permafrost thawing and other pavement distresses caused by permafrost thawing by controlling an oriented heat transfer in asphalt pavement.

Application of Linear Viscoelastic Properties in Semianalytical Finite Element Method with Recursive Time Integration to Analyze Asphalt Pavement Structure

Directory of Open Access Journals (Sweden)

Pengfei Liu

2018-01-01

Full Text Available Traditionally, asphalt pavements are considered as linear elastic materials in finite element (FE method to save computational time for engineering design. However, asphalt mixture exhibits linear viscoelasticity at small strain and low temperature. Therefore, the results derived from the elastic analysis will inevitably lead to discrepancies from reality. Currently, several FE programs have already adopted viscoelasticity, but the high hardware demands and long execution times render them suitable primarily for research purposes. Semianalytical finite element method (SAFEM was proposed to solve the abovementioned problem. The SAFEM is a three-dimensional FE algorithm that only requires a two-dimensional mesh by incorporating the Fourier series in the third dimension, which can significantly reduce the computational time. This paper describes the development of SAFEM to capture the viscoelastic property of asphalt pavements by using a recursive formulation. The formulation is verified by comparison with the commercial FE software ABAQUS. An application example is presented for simulations of creep deformation of the asphalt pavement. The investigation shows that the SAFEM is an efficient tool for pavement engineers to fast and reliably predict asphalt pavement responses; furthermore, the SAFEM provides a flexible, robust platform for the future development in the numerical simulation of asphalt pavements.

Modification of local asphalt with epoxy resin to be used in pavement

Directory of Open Access Journals (Sweden)

A.M.M. Abd El Rahman

2012-12-01

Full Text Available The durability of asphalt pavement is greatly influenced by the environmental changes during the year. In this paper, we prepared asphalt modified by mixing asphalt 60/70 with epoxidized natural rubber (ENR in different percentages (5, 10 and 15%, which was achieved using preformed peracetic acid (aqueous solution 59% at 60–80 °C, then molten cross-linker maleic anhydride (MA was added to modified asphalt until homogenous blends are achieved. Marshall test was used to evaluate the asphalt pavement performance depending on the curing time and hardener concentration. To measure marshall test, the pervious mixture was stirred with aggregate jop formula mix (JMF and 40% MA at 150–170 °C for 20 h and 1600 rpm. From the obtained data, it was found that asphalt mixed with 15% of ENR + 40% MA achieves a high stability (16,632 Newton, air voids of 2.5%, flow of 2.9 mm and mineral voids of 14.6%. While, the stability of the unmodified asphalt was (11,500 Newton, the flow 3.2 mm, the suitable air void value was 3.7% at 5.5% with the same conditions.

Ageing evolution of foamed warm mix asphalt combined with reclaimed asphalt pavement

International Nuclear Information System (INIS)

Perez-Martinez, M.; Marsac, P.; Gabet, T.; Pouget, S.; Hammoum, F.

2017-01-01

The combination of high rates of reclaimed asphalt pavement (RAP) and warm mix asphalt (WMA) technologies is still ambiguous in terms of durability. With the aim of clarifying this issue, a study comparing a hot mix asphalt with a WMA prepared using the foaming process technology. Both mixes contain 50% of RAP and are submitted to a laboratory ageing procedure. The long term related performance of the mixtures is compared by means of complex modulus and fatigue testing. Penetration and ring and ball tests are undertaken on the recovered bitumens, as well as the ageing evolution, characterised by the Fourier Transform Infrared analysis. Finally, the Apparent Molecular Weight Distribution (AMWD) of the binders is calculated from rheological measurements using the δ-method. Results show a relation between ageing evolution and mechanical performance. After ageing, the overall tendencies are similar for both processes. [es

Implementation of warm-mix asphalt mixtures in Nebraska pavements.

Science.gov (United States)

2012-07-01

The primary objective of this research is to evaluate the feasibility of several WMA mixtures as potential asphalt paving : mixtures for Nebraska pavements. To that end, three well-known WMA additives (i.e., Sasobit, Evotherm, and Advera : synthetic ...

Stress Regression Analysis of Asphalt Concrete Deck Pavement Based on Orthogonal Experimental Design and Interlayer Contact

Science.gov (United States)

Wang, Xuntao; Feng, Jianhu; Wang, Hu; Hong, Shidi; Zheng, Supei

2018-03-01

A three-dimensional finite element box girder bridge and its asphalt concrete deck pavement were established by ANSYS software, and the interlayer bonding condition of asphalt concrete deck pavement was assumed to be contact bonding condition. Orthogonal experimental design is used to arrange the testing plans of material parameters, and an evaluation of the effect of different material parameters in the mechanical response of asphalt concrete surface layer was conducted by multiple linear regression model and using the results from the finite element analysis. Results indicated that stress regression equations can well predict the stress of the asphalt concrete surface layer, and elastic modulus of waterproof layer has a significant influence on stress values of asphalt concrete surface layer.

Greenhouse gas emissions of alternative pavement designs: framework development and illustrative application.

Science.gov (United States)

Liu, Xiaoyu; Cui, Qingbin; Schwartz, Charles

2014-01-01

Pavement rehabilitation is carbon intensive and the choice of pavement type is a critical factor in controlling greenhouse gas (GHG) emissions. The existing body of knowledge is not able to support decision-making on pavement choice due to a lack of consensus on the system boundaries, the functional units and the estimation periods. Excessive data requirements further inhibit the generalization of the existing methodologies for design evaluation at the early planning stage. This study proposes a practical life-cycle GHG estimation approach, which is arguably effective to benchmark pavement emissions given project bid tabulation. A set of case studies conducted for this study suggest that recycled asphalt pavement (e.g., foam stabilized base (FSB), and warm mix asphalt (WMA)) would prevent up to 50% of GHGs from the initial construction phase. However, from a life-cycle perspective, pavement emissions are dictated largely by the traffic characteristics and the analysis period for the use phase. The benefits from using recycled materials (e.g., FSB) are likely to diminish if the recycled products do not perform as well as those properly proportioned with less recycled materials, or if the recycled materials are locally unavailable. When the AADT reaches 10,000, use phase releases more than 97% of the life cycle emissions and the emissions difference among alternative designs will be within 1%. Copyright © 2013 Elsevier Ltd. All rights reserved.

Sustainability and training materials for in-place recycling.

Science.gov (United States)

2016-04-22

Hot and cold in-place recycling techniques recycle 100 percent of a hot mix asphalt (HMA) pavement, in place, during the maintenance/rehabilitation process. Numerous studies have shown in-place recycling to be a sustainable, cost-effective procedure ...

Introductory asphalt technology; Nyumon asphalt gijutsu

Energy Technology Data Exchange (ETDEWEB)

Muroga, G. [Mitsubishi Oil Co. Ltd., Tokyo (Japan)

1994-12-28

The type and applications, manufacturing method, characteristics, road pavement etc. of asphalt were introduced. Among the petroleum asphalts, straight asphalt is used for road pavement,industry, and combustion, while blown asphalt is mainly used for the waterproofness of a building. Also, the demand for modified asphalt where rubber or thermoplastic elastomer was mixed is increasing. Straight asphalt is obtained by allowing atmospheric distillation tower bottom oil to be subjected to reduced pressure distillation and drawing reduced pressure gas oil and lubrication oil cut. Blown asphalt is produced by the oxidation dehydrogeneration and condensation polymerization reaction of soft straight asphalt. Rheology characteristics of asphalt are expressed by stiffness, relaxation elastic modulus, complex elastic modulus, etc. Also, asphalt has high electrical dielectric properties. Asphalt pavement has functions for dispersing traffic load and then transferring it to a lower layer, for resisting wear and cracking, and for preventing penetration of rainwater. 30 refs., 5 figs., 4 tabs.

Improving Quality Control of Asphalt Pavement with RAP Using a Portable Infrared Spectroscopy Device

Science.gov (United States)

2016-04-01

This project has investigated the effectiveness of a Portable Infrared Spectrometer (PIRS) device in estimating percent of Reclaimed Asphalt Pavement (RAP) and its contribution into oxidative aging of a new asphalt mixture immediately after productio...

Recycling of polyethylene terephthalate (PET plastic bottle wastes in bituminous asphaltic concrete

Directory of Open Access Journals (Sweden)

Adebayo Olatunbosun Sojobi

2016-12-01

Full Text Available This research sheds light on the concept of eco-friendly road construction which comprises eco-design, eco-extraction, eco-manufacturing, eco-construction, eco-rehabilitation, eco-maintenance, eco-demolition, and socioeconomic empowerment. It also revealed the challenges being faced in its adoption and the benefits derivable from its application. Furthermore, the effects of recycling PET plastic bottle wastes produced in North Central Nigeria in bituminous asphaltic concrete (BAC used in flexible pavement construction were also evaluated. The mix design consists of 60/70 penetration-grade asphaltic concrete (5%, 68% coarse aggregate, 6% fine aggregate, and 21% filler using the dry process at 170°C. The optimum bitumen content (OBC for conventional BAC was obtained as 4% by weight of total aggregates and filler. Polymer-coated aggregate (PCA-modified BAC seems preferable because it has the potential to utilize more plastic wastes with a higher optimum plastic content (OPC of 16.7% by weight of total aggregates and filler compared to that of 9% by weight of OBC achieved by PMB-BAC. For both PMB- and PCA-modified BAC, an increase in air void, void in mineral aggregate, and Marshall stability were observed. Eco-friendly road construction which recycles PET wastes should be encouraged by government considering its potential environmental and economic benefits.

Effects of conductive fillers on temperature distribution of asphalt pavements

International Nuclear Information System (INIS)

Chen Mingyu; Wu Shaopeng; Zhang Yuan; Wang Hong

2010-01-01

The sun provides a cheap and abundant source of clean and renewable energy. Solar cells have been used to capture this energy and generate electricity. A more useful form of the solar cell would be asphalt pavements, which get heated up by solar radiation. Graphite powders are utilized as thermal conductive fillers to make an asphalt collector conductive so as to improve the efficiency of the asphalt collector. Accounting for the important application conditions and evaluating the effects of the heat conductive materials and the solar energy absorbability of the conductive asphalt collector, a finite element model has been developed to predict temperature distributions in the conductive asphalt solar collector. In this study, an experimental validation exercise was conducted using the measured data taken from full-depth asphalt slabs. Validation results showed that the model can satisfactorily predict the temperature distributions in asphalt concrete slabs. The optimal depth is 25-50 mm for placing pipes that serve as the heat exchanger. Meanwhile, the effect of the surroundings on the solar energy potential of the asphalt collector was noticeable.

Influence of Hydrated Lime on the Properties and Permanent Deformation of the Asphalt Concrete Layers in Pavement

Directory of Open Access Journals (Sweden)

Al-Tameemi Ahmed F.

2015-07-01

Full Text Available Flexible or asphalt concrete pavement is the paving system most widely adopted all over the world. It has been recognized that there are many different types of the factors affecting the performance and durability of asphalt concrete pavement, including the service conditions, such as: the variation of temperature from mild to extremes and the repeated excessive axle loading as well as the inadequate quality of the raw materials. All of these when combined together are going to accelerate the occurrence of distresses in flexible pavement such as permanent deformation and fatigue cracking. As the result, there has an urgent need to enhance the ability of asphalt concrete mixture to resist distresses happened in pavement. Use of additives is one of the techniques adopted to improve pavement properties. It has been found that hydrated lime might be one of the effective additives because it is widely available and relatively cheap compared to other modifiers like polymers. This paper presents an experimental study of the hydrated-lime modified asphalt concrete mixtures. Five different percentages of the hydrated lime additive were investigated, namely (1, 1.5, 2, 2.5 and 3 percent. The hydrated lime additive was used as partial replacement of limestone filler by total weight of the aggregate. The designed Hot Mix Asphalt (HMA concretes are for the application of three pavement courses, i.e. Surface, Leveling and Base. These mixtures are designed and tested following Marshall procedure and uniaxial repeated loading to evaluate permanent deformation at different temperatures of 20°C, 40°C and 60°C. The experimental results show that the addition of hydrated lime as a partial replacement of ordinary limestone mineral filler results a significant improvement on mechanical properties and the resistant to permanent deformation of the designed asphalt concrete mixtures.

Influence of bitumen type on cracking resistance of asphalt mixtures used in pavement overlays

Science.gov (United States)

Jaskula, P.; Szydlowski, C.; Stienss, M.

2018-05-01

Cracking is one of the predominant distresses occurring in flexible pavements, especially in old pavements that were rehabilitated with an asphalt overlay. In such cases asphalt mixtures should be designed to ensure high resistance to reflective cracking because new asphalt layers are exposed to existing cracks of the old pavement. The nature of these cracks can be various (transverse, longitudinal as well as crazy cracking). One factor that minimizes this type of distress is the proper mix design process, which should involve selection of specific bitumen binder and mineral mix gradation. However, still there is no universally adopted laboratory test method that would allow to clearly assess resistance of asphalt mixtures to reflective cracking. This paper describes the usage of one of the devices developed to test asphalt mixtures in terms of such distress – Texas Overlay Tester. For this test, samples prepared in laboratory conditions (i.e. compacted with the use of Superpave Gyratory Compactor) as well as obtained in the field (by core drilling) can be used. The results are obtained not only quickly and easily, but also with sufficient repeatability. The described method characterizes both crack initiation and crack propagation properties of asphalt mixtures. In this work one type of mineral mixture was tested with 4 different types of bitumen (one neat bitumen, two ordinary polymer-modified and one polymer-modified with high polymer content). For selected cases extra additives (rubber and loose fibres) were also tested. In total, six asphalt mixtures were tested. A ranking of the used binders was created on the basis of the results in order to conclude which bitumen would ensure the best performance characteristics in terms of reflective cracking. The results have clearly shown that deliberate choice of the binder used in the asphalt mixture for the overlay will significantly improve its reflective cracking resistance or even fatigue resistance.

Investigation of the Effect of Recycled Asphalt Pavement Material on Permeability and Bearing Capacity in the Base Layer

Directory of Open Access Journals (Sweden)

Ayşegül Güneş Seferoğlu

2018-01-01

Full Text Available The purpose of this research was to investigate the effects of recycled asphalt pavement (RAP and cement content on the permeability and bearing capacity characteristics of aggregate base courses. Mixtures containing untreated RAP ranging between 0 and 100 percent and 1, 2, and 3% cement-treated RAP were subjected to laboratory tests (bitumen content, sieve analysis, modified proctor, soaked California bearing ratio (CBR, and constant-level permeability tests. The results showed that, as the RAP percentage in the mixture increased, CBR values decreased considerably. Moreover, there is a linear increase in the CBR values with cement treatment. Optimum moisture contents (OMC and maximum dry densities (MDD showed a decreasing trend. Increasing the cement percentages in 100% RAP blend increases the OMC and MDD values. The permeability of RAP showed a decrease as the percentage of RAP and cement increased in blends. The study showed that the CBR value of the 20% RAP blend is also obtained in the 100% RAP/3% cement-treated blend. Thus, it has been understood that cement is a suitable material in order to increase the use of RAP. In addition, the increase in the percentage of RAP and cement made the base course more impermeable.

Analytical approach for evaluating temperature field of thermal modified asphalt pavement and urban heat island effect

International Nuclear Information System (INIS)

Chen, Jiaqi; Wang, Hao; Zhu, Hongzhou

2017-01-01

Highlights: • Derive an analytical approach to predict temperature fields of multi-layered asphalt pavement based on Green’s function. • Analyze the effects of thermal modifications on heat output from pavement to near-surface environment. • Evaluate pavement solutions for reducing urban heat island (UHI) effect. - Abstract: This paper aims to present an analytical approach to predict temperature fields in asphalt pavement and evaluate the effects of thermal modification on near-surface environment for urban heat island (UHI) effect. The analytical solution of temperature fields in the multi-layered pavement structure was derived with the Green’s function method, using climatic factors including solar radiation, wind velocity, and air temperature as input parameters. The temperature solutions were validated with an outdoor field experiment. By using the proposed analytical solution, temperature fields in the pavement with different pavement surface albedo, thermal conductivity, and layer combinations were analyzed. Heat output from pavement surface to the near-surface environment was studied as an indicator of pavement contribution to UHI effect. The analysis results show that increasing pavement surface albedo could decrease pavement temperature at various depths, and increase heat output intensity in the daytime but decrease heat output intensity in the nighttime. Using reflective pavement to mitigate UHI may be effective for an open street but become ineffective for the street surrounded by high buildings. On the other hand, high-conductivity pavement could alleviate the UHI effect in the daytime for both the open street and the street surrounded by high buildings. Among different combinations of thermal-modified asphalt mixtures, the layer combination of high-conductivity surface course and base course could reduce the maximum heat output intensity and alleviate the UHI effect most.

Field investigation of skid resistance degradation of asphalt pavement during early service

Directory of Open Access Journals (Sweden)

Yinghao Miao

2016-07-01

Full Text Available This paper documents a field investigation into the skid resistance degradation of asphalt pavement during early service. Field tests were conducted 7 times during more than 2 years. There are 2 highway sections included in the field tests, which cover 4 asphalt surface types, i.e., dense asphalt concrete (DAC, rubber asphalt concrete (RAC, stone matrix asphalt (SMA, and ultra-thin wearing course (UTWC. Macrotexture and friction data were collected using the sand patch method and the dynamic friction tester respectively. The degradation of the mean texture depth (MTD and the friction coefficient at slip speed of 60 km/h (DFT60 were analyzed. The international friction index (IFI was also calculated using the friction coefficient at slip speed of 20 km/h (DFT20 with MTD to evaluate the skid resistance degradation. The UTWC has relatively good skid resistance even after 7.4 × 106 standard vehicle passes. The SMA has very stable friction performance which maintains almost the same friction level after 4.61 × 106 standard vehicle passes. The DAC and RAC have relatively poor friction performance while the RAC has better macrotexture. The changing trends of skid resistance with traffic wear can be fitted by a logarithmic model for all surface types. The SMA and UTWC have relatively clear relationship between DFT20 and MTD, while the RAC and the DAC show more complex. Keywords: Asphalt pavement, Skid resistance, Degradation, International friction index

Quantifying the environmental burdens of the hot mix asphalt (HMA pavements and the production of warm mix asphalt (WMA

Directory of Open Access Journals (Sweden)

Mithil Mazumder

2016-05-01

Full Text Available Asphalt pavement has significant environmental burdens throughout its life cycle. A life cycle assessment (LCA model is used to quantify the environmental burdens for material, construction, maintenance and use phases of hot mix asphalt (HMA pavement. Two peer reviewed journals have been used to collect all of the inventory loadings as an input for the LCA model and ten impact categories have been evaluated as output. The result of the inventory analysis is a summary of all inflows and outflows related to the “functional unit”. The result of each impact category is the total of all the individually characterized inventory loadings in each category. Each life cycle phase of HMA pavement has been quantified on these ten impact categories and a comparison provided among the phases to understand the percentage contribution to the environment. Human and eco toxicity values are higher for the material phase, whereas the rest of the impact categories are significant in the use phase. The material phase contributes 97% of the overall human toxicity in water from standpoint of asphalt pavements, whereas in the material phase the production of bitumen is responsible for 90% human and eco toxicity in terms of air based burden. As a solution, the life cycle inventory of WMA has been estimated and reduction only done in HMA production. From analysis, it was estimated that WMA provides a reduction of 29% on the acidification impact and 25% reduction on both fossil fuel consumption and photo oxidant formation impact of HMA. Keywords: Life cycle analysis, Environmental burdens, Inventories, HMA, Impacts, WMA

Performance of Asphalt Concrete Wearing Course (AC-WC) Utilizing Reclaimed Asphalt Pavement from Cold Milling Bound with 80/100 Pen Asphalt

Science.gov (United States)

Thanya, I. N. A.; Suweda, I. W.; Putra, G. K.

2018-03-01

Demands on natural aggregate materials for road pavement can be reduced by utilizing reclaimed asphalt pavement (RAP). This research was aimed at evaluating the performance of AC-WC mixture using RAP materials from cold milling, bound with 80/100 pen asphalt. The RAP aggregate gradation was adjusted by adding the required amount of natural aggregates to meet the specification in Indonesia. The RAP and added aggregates were hotmixed and compacted with Marshall hummer at 2×75 blows. The asphalt content were varied. It was found that the optimum asphalt content was 6.05 % with the following Marshall characteristics: stability 1237.08 kg; flow 3.36 mm; Marshall quotient 324,73kg/mm; void in mix (VIM) 3,360%; void in mineral aggregate (VMA) 15.103; and void filled with bitumen (VFB) 77.759% and residual stability 91.04; all met the Indonesian specification. The cantabro abration loss (CAL) at 30°C was 9,02%. The indirect tensile stiffness modulus (ITSM) at 20 °C was 7961.4 MPa; dynamic creep with 100 kPa pressure at 40°C gave slope 0.0112 microsstrain/pulse which is suitable for heavy load traffic. The fatigue test results was obtained at increased stress level, i.e. at 900, 1100, and 1300 kPa. Based on the equation derived from the fatigue strain and repeated loading relationship, at 100 microstrain (με) the repeated load was 434,661.58 times, and at one million (106) repeated loading, the samples could withstand strain of 92,38 microstrain. The performance of the samples were overall better than AC-WC mixture using virgin aggregates bound with 60/70 pen asphalt.

Experimental testing of hot mix asphalt mixture made of recycled aggregates.

Science.gov (United States)

Rafi, Muhammad Masood; Qadir, Adnan; Siddiqui, Salman Hameed

2011-12-01

The migration of population towards big cities generates rapid construction activities. These activities not only put pressure on natural resources but also produce construction, renovation and demolition waste. There is an urgent need to find out ways to handle this waste owing to growing environmental concerns. This can reduce pressure on natural resources as well. This paper presents the results of experimental studies which were carried out on hot mix asphalt mixture samples. These samples were manufactured by adding recycled aggregates (RA) with natural crushed stone aggregates (CSA). Three levels of addition of RA were considered in the presented studies. RA were obtained from both the concrete waste of construction, renovation and demolition activities and reclaimed asphalt pavement. Separate samples were manufactured with the coarse and fine aggregate fractions of both types of RA. Samples made with CSA were used as control specimens. The samples were prepared and tested using the Marshall method. The performance of the samples was investigated in terms of density-void and stability/flow analysis and was compared with the performance criteria as given by National Highway Authority for wearing course material in Pakistan. Based on this data optimum asphalt contents were determined. All the samples made by adding up to 50% RA conform to the specification requirements of wearing course material as given by National Highway Authority in terms of optimum asphalt contents, voids in mineral aggregates and stability/flow. A statistical analysis of variation of these samples confirmed that addition is also possible statistically.

Design Method for Proportion of Cement-Foamed Asphalt Cold Recycled Mixture

Directory of Open Access Journals (Sweden)

Li Junxiao

2018-01-01

Full Text Available Through foaming experiment of Zhongtai AH-70 asphalt, the best foaming temperature water consumption and influence factors of foamed asphalt’s foaming features are determined; By designing the proportion of foamed asphalt cold in-place recycled mixture combined with the water stability experiment, for this mixture the best foamed asphalt addition is 3%, and proportion of the mixture is RAP: fine aggregate: cement=75:23:2. Using SEM technology, the mechanism of increasing on the intensity of foamed asphalt mixture resulted by the addition of cement was analysed. This research provides reference for cement admixture’s formulation in the designing of foamed asphalt cold in-place recycled mixture.

Numerical Simulation for Mechanical Behavior of Asphalt Pavement with Graded Aggregate Base

Directory of Open Access Journals (Sweden)

Dongliang He

2018-01-01

Full Text Available The performance of asphalt pavement is determined by the combination of its material properties, road structure, and loading configurations. A DEM numerical simulation study was conducted to determine stress distribution and deformation behavior of asphalt pavement with graded aggregate base under standard traffic loading. Stress contour and displacement contour were presented via a self-made program. Compressive stress concentrated area located in both sides of wheel, while tensile stress concentrated area appeared in lower part of the asphalt layer. The traffic loading transferred downward by graded aggregate base and to both sides at the same time, and has a trend to expand gradually with increasing depth within graded aggregate base. Therefore, stress was well distributed in the subgrade soil layer with a great action scope, and the value decreased obviously because of the stress dispersion of graded aggregate base. Vertical displacement was the main displacement of the asphalt layer, and on the both sides of traffic loading, displacement was downward and inclined slightly to the central of loading. Vertical and horizontal deformations included in both graded aggregate base layers, and displacement extended to both sides gradually with increasing depth corresponding to stress-distribution trends. Vertical displacement was dominated in the subgrade soil layer which was relatively small.

Evaluation of recycled concrete as aggregate in new concrete pavements.

Science.gov (United States)

2014-04-01

This study evaluated the use of recycled concrete as coarse aggregate in new concrete pavements. : Recycled concrete aggregate (RCA) produced from demolished pavements in three geographically dispersed locations in Washington state were used to perfo...

Partial substitution of asphalt pavement with modified sulfur

Directory of Open Access Journals (Sweden)

E.R. Souaya

2015-12-01

Full Text Available The use of sulfur in pavement laying was developed in 1980 but it was restricted in the late 19th century due to its environmental problems and its high reactivity toward oxidation processes which give sulfuric acid products that are capable of destroying the asphalt mixture. The study involved the conversion of elemental sulfur to a more stable modified one using a combination of byproducts of olefin hydrocarbons that were obtained from petroleum fractional distillates and cyclic hydrocarbon bituminous residue at 145 °C. The changes in the structural characteristics and morphology of prepared modified sulfur were studied using XRD and SEM respectively. Also DSC curves help us to elucidate the changes in sulfur phases from α-orthorhombic to β-mono clinic structure. The technique of nanoindentation helps us to compare the mechanical properties of modified and pure sulfur including modulus of elasticity and hardness. The hot mixture asphalt designs were prepared according to the Marshall Method in which the asphalt binder content was partially substituted with 20%, 30%, 40%, and 50% modified sulfur. The mechanical properties were measured including Marshall Stability, flow, air voids, and Marshall Stiffness. From the overall study, the results indicated that asphalt could partially be substituted with modified sulfur with no significant deleterious effect on performance and durability of hot mixed asphalt.

Quality control of recycled asphaltic concrete : final report.

Science.gov (United States)

1982-07-01

This study examined the variations found in recycled asphaltic concrete mix based upon plant quality control data and verification testing. The data was collected from four recycled hot-mix projects constructed in 1981. All plant control and acceptan...

Stormwater quality of spring-summer-fall effluent from three partial-infiltration permeable pavement systems and conventional asphalt pavement.

Science.gov (United States)

Drake, Jennifer; Bradford, Andrea; Van Seters, Tim

2014-06-15

This study examined the spring, summer and fall water quality performance of three partial-infiltration permeable pavement (PP) systems and a conventional asphalt pavement in Ontario. The study, conducted between 2010 and 2012, compared the water quality of effluent from two Interlocking Permeable Concrete Pavements (AquaPave(®) and Eco-Optiloc(®)) and a Hydromedia(®) Pervious Concrete pavement with runoff from an Asphalt control pavement. The usage of permeable pavements can mitigate the impact of urbanization on receiving surface water systems through quantity control and stormwater treatment. The PP systems provided excellent stormwater treatment for petroleum hydrocarbons, total suspended solids, metals (copper, iron, manganese and zinc) and nutrients (total-nitrogen and total-phosphorus) by reducing event mean concentrations (EMC) as well as total pollutant loadings. The PPs significantly reduced the concentration and loading of ammonia (NH4(+)+NH3), nitrite (NO2(-)) and organic-nitrogen (Org-N) but increased the concentration and loading of nitrate (NO3(-)). The PP systems had mixed performances for the treatment of phosphate (PO4(3-)). The PP systems increased the concentration of sodium (Na) and chloride (Cl) but EMCs remained well below recommended levels for drinking water quality. Relative to the observed runoff, winter road salt was released more slowly from the PP systems resulting in elevated spring and early-summer Cl and Na concentrations in effluent. PP materials were found to introduce dissolved solids into the infiltrating stormwater. The release of these pollutants was verified by additional laboratory scale testing of the individual pavement and aggregate materials at the University of Guelph. Pollutant concentrations were greatest during the first few months after construction and declined rapidly over the course of the study. Copyright © 2014 Elsevier Ltd. All rights reserved.

Determine viscoelastic mechanical properties of warm mix asphalt (WMA)-reclaimed asphalt pavement (RAP) mixes under high stresses in air-field flexible pavements and its impact on design life.

Science.gov (United States)

2014-06-01

The introduction of larger aircrafts on flexible airfield pavements has led to a need for asphalt mixtures capable of sustaining such heavy : loads. This laboratory and analytical study investigated the mechanical responses of a number of modified as...

Hot-mix asphalt testing for the South African pavement design method

CSIR Research Space (South Africa)

Anochie-Boateng, Joseph

2010-08-01

Full Text Available of local and international hot-mix asphalt (HMA) test methods and modify or adapt them to suit South African road pavement conditions. This paper presents various laboratory HMA test protocols developed as part of the project to revise SAPDM. Large scale...

Sensitivity analysis of longitudinal cracking on asphalt pavement using MEPDG in permafrost region

Directory of Open Access Journals (Sweden)

Chen Zhang

2015-02-01

Full Text Available Longitudinal cracking is one of the most important distresses of asphalt pavement in permafrost regions. The sensitivity analysis of design parameters for asphalt pavement can be used to study the influence of every parameter on longitudinal cracking, which can help optimizing the design of the pavement structure. In this study, 20 test sections of Qinghai–Tibet Highway were selected to conduct the sensitivity analysis of longitudinal cracking on material parameter based on Mechanistic-Empirical Pavement Design Guide (MEPDG and single factorial sensitivity analysis method. Some computer aided engineering (CAE simulation techniques, such as the Latin hypercube sampling (LHS technique and the multiple regression analysis are used as auxiliary means. Finally, the sensitivity spectrum of material parameter on longitudinal cracking was established. The result shows the multiple regression analysis can be used to determine the remarkable influence factor more efficiently and to process the qualitative analysis when applying the MEPDG software in sensitivity analysis of longitudinal cracking in permafrost regions. The effect weights of the three parameters on longitudinal cracking in descending order are air void, effective binder content and PG grade. The influence of air void on top layer is bigger than that on middle layer and bottom layer. The influence of effective asphalt content on top layer is bigger than that on middle layer and bottom layer, and the influence of bottom layer is slightly bigger than middle layer. The accumulated value of longitudinal cracking on middle layer and bottom layer in the design life would begin to increase when the design temperature of PG grade increased.

Application Research of Quality Control Technology of Asphalt Pavement based on GPS Intelligent

Science.gov (United States)

Wang, Min; Gao, Bo; Shang, Fei; Wang, Tao

2017-10-01

Due to the difficulty of steel deck pavement asphalt layer compaction caused by the effect of the flexible supporting system (orthotropic steel deck plate), it is usually hard and difficult to control for the site compactness to reach the design goal. The intelligent compaction technology is based on GPS control technology and real-time acquisition of actual compaction tracks, and then forms a cloud maps of compaction times, which guide the roller operator to do the compaction in accordance with the design requirement to ensure the deck compaction technology and compaction quality. From the actual construction situation of actual bridge and checked data, the intelligent compaction technology is significant in guaranteeing the steel deck asphalt pavement compactness and quality stability.

Performance Evaluation of Stone Mastic Asphalt and Hot Mix Asphalt Mixtures Containing Recycled Concrete Aggregate

Directory of Open Access Journals (Sweden)

Mohammad Saeed Pourtahmasb

2014-01-01

Full Text Available Environmental and economic considerations have encouraged civil engineers to find ways to reuse recycled materials in new constructions. The current paper presents an experimental research on the possibility of utilizing recycled concrete aggregates (RCA in stone mastic asphalt (SMA and hot mix asphalt (HMA mixtures. Three categories of RCA in various percentages were mixed with virgin granite aggregates to produce SMA and HMA specimens. The obtained results indicated that, regardless of the RCA particular sizes, the use of RCA to replace virgin aggregates increased the needed binder content in the asphalt mixtures. Moreover, it was found that even though the volumetric and mechanical properties of the asphalt mixtures are highly affected by the sizes and percentages of the RCA but, based on the demands of the project and traffic volume, utilizing specific amounts of RCA in both types of mixtures could easily satisfy the standard requirements.

Evaluation of recycled hot mix asphalt concrete on Route 220 : final report.

Science.gov (United States)

1985-01-01

This report describes the performance of an approximately 8-mi section of roadway on which the rod two layers of asphalt concrete were milled, recycled through a conventional asphalt batch plant, and relaid. The recycled mix consisted of about 40% re...

Ultrasound data for laboratory calibration of an analytical model to calculate crack depth on asphalt pavements

Directory of Open Access Journals (Sweden)

Miguel A. Franesqui

2017-08-01

Full Text Available This article outlines the ultrasound data employed to calibrate in the laboratory an analytical model that permits the calculation of the depth of partial-depth surface-initiated cracks on bituminous pavements using this non-destructive technique. This initial calibration is required so that the model provides sufficient precision during practical application. The ultrasonic pulse transit times were measured on beam samples of different asphalt mixtures (semi-dense asphalt concrete AC-S; asphalt concrete for very thin layers BBTM; and porous asphalt PA. The cracks on the laboratory samples were simulated by means of notches of variable depths. With the data of ultrasound transmission time ratios, curve-fittings were carried out on the analytical model, thus determining the regression parameters and their statistical dispersion. The calibrated models obtained from laboratory datasets were subsequently applied to auscultate the evolution of the crack depth after microwaves exposure in the research article entitled “Top-down cracking self-healing of asphalt pavements with steel filler from industrial waste applying microwaves” (Franesqui et al., 2017 [1].

Ultrasound data for laboratory calibration of an analytical model to calculate crack depth on asphalt pavements.

Science.gov (United States)

Franesqui, Miguel A; Yepes, Jorge; García-González, Cándida

2017-08-01

This article outlines the ultrasound data employed to calibrate in the laboratory an analytical model that permits the calculation of the depth of partial-depth surface-initiated cracks on bituminous pavements using this non-destructive technique. This initial calibration is required so that the model provides sufficient precision during practical application. The ultrasonic pulse transit times were measured on beam samples of different asphalt mixtures (semi-dense asphalt concrete AC-S; asphalt concrete for very thin layers BBTM; and porous asphalt PA). The cracks on the laboratory samples were simulated by means of notches of variable depths. With the data of ultrasound transmission time ratios, curve-fittings were carried out on the analytical model, thus determining the regression parameters and their statistical dispersion. The calibrated models obtained from laboratory datasets were subsequently applied to auscultate the evolution of the crack depth after microwaves exposure in the research article entitled "Top-down cracking self-healing of asphalt pavements with steel filler from industrial waste applying microwaves" (Franesqui et al., 2017) [1].

Deformation Parameters and Fatigue of the Recycled Asphalt Mixtures

Directory of Open Access Journals (Sweden)

Šrámek Juraj

2015-12-01

Full Text Available The deformational properties of asphalt mixtures measured by dynamic methods and fatigue allow a design the road to suit the expected traffic load. Quality of mixtures is also expressed by the resistance to permanent deformation. Complex modulus of stiffness and fatigue can reliably characterize the proposed mixture of asphalt pavement. The complex modulus (E* measurement of asphalt mixtures are carried out in laboratory of Department of Construction Management at University of Žilina by two-point bending test method on trapezoid-shaped samples. Today, the fatigue is verified on trapezoid-shaped samples and is assessed by proportional strain at 1 million cycles (ε6. The test equipment and software is used to evaluate fatigue and deformation characteristics.

Application of waste tires to asphalt pavement. Improvement of adhesion of asphalt with rubber particles; Haitaiya no asphalt hoso eno tekiyo. Asphalt to gomu ryushi no fuchakusei no kairyo ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Nakaoka, I. [Kansai Electric Power Co. Inc., Osaka (Japan)

1994-10-10

With an objective to apply waste tires to asphalt pavement, an experiment was carried out to improve adhesion of asphalt with rubber particles by using polymers. The state of interface on rubber particle and asphalt mixture was observed by a scanning electron microscope. As a result, it was found that the surface of untreated rubber particles is not bonded with the asphalt, but polymer treated mixture was found to have the affinity of rubber particles with asphalt improved. Tensile bonding strength was tested on rubber plates and asphalt. The result revealed that the polymer-reformed mixture has two times as large tensile bonding strength as that of the untreated mixture. With regard to the characters of asphalt mixture mixed with rubber particles, the stability shows a decreasing trend as compared with the standard asphalt concrete, but presents an excellent performance in wear. The fluidity resistance value is inferior to the standard, but not as great as presenting a problem under normal using environment, where its applicability as a road paving material was verified. 4 figs., 2 tabs.

Concentrations of polycyclic aromatic hydrocarbons (PAHs) and azaarenes in runoff from coal-tar- and asphalt-sealcoated pavement

International Nuclear Information System (INIS)

Mahler, Barbara J.; Van Metre, Peter C.; Foreman, William T.

2014-01-01

Coal-tar-based sealcoat, used extensively on parking lots and driveways in North America, is a potent source of PAHs. We investigated how concentrations and assemblages of PAHs and azaarenes in runoff from pavement newly sealed with coal-tar-based (CT) or asphalt-based (AS) sealcoat changed over time. Samples of simulated runoff were collected from pavement 5 h to 111 d following application of AS or CT sealcoat. Concentrations of the sum of 16 PAHs (median concentrations of 328 and 35 μg/L for CT and AS runoff, respectively) in runoff varied relatively little, but rapid decreases in concentrations of azaarenes and low molecular weight PAHs were offset by increases in high molecular weight PAHs. The results demonstrate that runoff from CT-sealcoated pavement, in particular, continues to contain elevated concentrations of PAHs long after a 24-h curing time, with implications for the fate, transport, and ecotoxicological effects of contaminants in runoff from CT-sealcoated pavement. - Highlights: • We compare PAH and azaarene concentrations in runoff from coal-tar- and asphalt-sealed pavement. • Concentrations in coal-tar-sealcoat runoff greatly exceeded those in asphalt-sealcoat runoff. • Decreases in azaarenes and LMW PAHs were offset by increases in HMW PAHs. • PAH concentrations in coal-tar-sealcoat runoff remained high for months after application. - Concentrations of PAHs in runoff from pavement with coal-tar-based sealcoat continue to be elevated for at least 3 months following sealcoat application

Performance on Water Stability of Cement-Foamed Asphalt Cold Recycled Mixture

Directory of Open Access Journals (Sweden)

Li Junxiao

2018-01-01

Full Text Available Through designing the mixture proportion of foamed asphalt cold in-place recycled mixture combined with the water stability experiment, it shows that the addition of cement can obviously improve foamed asphalt mixture’s water stability and the best cement admixture is between 1% ~ 2%; Using digital imaging microscope and SEM technology, the mechanism of increasing on the intensity of foamed asphalt mixture resulted by adding cement was analyzed. It revealed that the cement hydration products contained in the foamed asphalt mixture hydrolyzed into space mesh structure and wrapped up the aggregate particle, this is the main reason that the cement can enhance the mixture’s intensity as well as the water stability. This research provides reference for cement admixture’s formulation in the designing of foamed asphalt cold in-place recycled mixture.

A study on engineering characteristics of asphalt concrete using filler with recycled waste lime.

Science.gov (United States)

Sung Do, Hwang; Hee Mun, Park; Suk keun, Rhee

2008-01-01

This study focuses on determining the engineering characteristics of asphalt concrete using mineral fillers with recycled waste lime, which is a by-product of the production of soda ash (Na(2)CO(3)). The materials tested in this study were made using a 25%, 50%, 75%, and 100% mixing ratio based on the conventional mineral filler ratio to analyze the possibility of using recycled waste lime. The asphalt concretes, made of recycled waste lime, hydrated lime, and conventional asphalt concrete, were evaluated through their fundamental engineering properties such as Marshall stability, indirect tensile strength, resilient modulus, permanent deformation characteristics, moisture susceptibility, and fatigue resistance. The results indicate that the application of recycled waste lime as mineral filler improves the permanent deformation characteristics, stiffness and fatigue endurance of asphalt concrete at the wide range of temperatures. It was also determined that the mixtures with recycled waste lime showed higher resistance against stripping than conventional asphalt concrete. It was concluded from various test results that a waste lime can be used as mineral filler and, especially, can greatly improve the resistance of asphalt concrete to permanent deformation at high temperatures.

Strength, shrinkage, erodibility and capillary flow characteristics of cement-treated recycled pavement materials

Directory of Open Access Journals (Sweden)

William Fedrigo

2017-09-01

Full Text Available Full-depth recycling with portland cement (FDR-PC has been widely used for pavement rehabilitation; however, doubts remain regarding factors affecting some properties of the recycled material. Aiming on quantifying the effects of those factors on the strength, drying shrinkage, erodibility, capillary rise and absorption of cement-treated mixtures (CTM of reclaimed asphalt pavement (RAP and graded crushed stone, tests were conducted considering different RAP contents, cement contents, compaction efforts and curing times. Cement addition increased the mixtures strength and reduced their erodibility and capillary flow characteristics, but increased shrinkage. Low cement contents resulted in acceptable strength for CTM, but in high capillary rise and absorption, not being suitable if the layer is exposed to long periods of water soaking. Higher compaction effort led to similar effects as cement addition, counterbalancing low cement contents usage and reducing costs and shrinkage cracking risk. Strength and shrinkage showed higher growth rates at early stages, and then precautions should be taken in order to avoid moisture loss. Increasing RAP content decreased strength; though, RAP effect on the other properties was statistically non-significant, indicating a similar behaviour as CTM without RAP. Considering the studied properties, the mixture with most satisfactory behaviour for field applications was identified. The results highlighted strength is not the only property to be considered when designing FDR-PC mixtures; although presenting acceptable strength, some mixtures may fail due to shrinkage cracking or erosion, when exposed to water content variations. Keywords: Full-depth recycling with cement, Strength, Drying shrinkage, Erodibility, Capillary rise, Absorption

Assessing Asphalt and Concrete Pavement Surface Texture in the Field

Directory of Open Access Journals (Sweden)

Saad I. Sarsam

2016-06-01

Full Text Available The incorporation of safety characteristics into the traditional pavement structural design or in the functional evaluation of pavement condition has not been established yet. The design has focused on the structural capacity of the roadway so that the pavement can withstand specific level of repetitive loading over the design life. On the other hand, the surface texture condition was neither included in the AASHTO design procedure nor in the present serviceability index measurements. The pavement surface course should provide adequate levels of friction and ride quality and maintain low levels of noise and roughness. Many transportation departments perform routine skid resistant testing, the type of equipment used for testing varies depending on the preference of each transportation department. It was felt that modeling of the surface texture condition using different methods of testing may assist in solving such problem. In this work, Macro texture and Micro texture of asphalt and cement concrete pavement surface have been investigated in the field using four different methods (The Sand Patch Method, Outflow Time Method, British Pendulum Tester and Photogrammetry Technique. Two different grain sizes of sand have been utilized in conducting the Sand Patch while the Micro texture was investigated using the British Pendulum tester method at wet pavement surface conditions. The test results of the four methods were correlated to the skid number. It was concluded that such modeling could provide instant data in the field for pavement condition which may help in pavement maintenance management.

Review and environmental impact assessment of green technologies for base courses in bituminous pavements

Energy Technology Data Exchange (ETDEWEB)

Anthonissen, Joke, E-mail: joke.anthonissen@uantwerpen.be [Faculty of Applied Engineering, University of Antwerp, Rodestraat 4, 2000 Antwerp (Belgium); Van den bergh, Wim, E-mail: wim.vandenbergh@uantwerpen.be [Faculty of Applied Engineering, University of Antwerp, Rodestraat 4, 2000 Antwerp (Belgium); Braet, Johan, E-mail: johan.braet@uantwerpen.be [Department Engineering Management, Faculty of Applied Economics, University of Antwerp, Prinsstraat 13, 2000 Antwerp (Belgium)

2016-09-15

This paper provides a critical review of different approaches applied in the Belgian asphalt sector in order to reduce the environmental impact of bituminous road construction works. The focus is on (1) reusing reclaimed asphalt pavement, (2) reducing the asphalt production temperature, and (3) prolonging the service life of the pavement. Environmental impact assessment of these methods is necessary to be able to compare these approaches and understand better the ability to reduce the environmental impact during the life cycle of the road pavement. Attention should be drawn to the possible shift in environmental impact between various life cycle stages, e.g., raw material production, asphalt production, or waste treatment. Life cycle assessment is necessary to adequately assess the environmental impact of these approaches over the entire service life of the bituminous pavement. The three approaches and their implementation in the road sector in Flanders (region in Belgium) are described and the main findings from life cycle assessment studies on these subjects are discussed. It was found from the review that using reclaimed asphalt pavement in new bituminous mixtures might yield significant environmental gains. The environmental impact of the application of warm mix asphalt technologies, on the other hand, depends on the technique used. - Highlights: • Recycling, lower production temperature and durability of asphalt are investigated. • The use of RAP in new asphalt mixtures yields significant environmental advantages. • It would be beneficial to allow RAP in asphalt mixtures for wearing courses. • The use of particular additives might counteract the environmental gain from WMA. • The service life and the environmental data source influence the LCA results.

Review and environmental impact assessment of green technologies for base courses in bituminous pavements

International Nuclear Information System (INIS)

Anthonissen, Joke; Van den bergh, Wim; Braet, Johan

2016-01-01

This paper provides a critical review of different approaches applied in the Belgian asphalt sector in order to reduce the environmental impact of bituminous road construction works. The focus is on (1) reusing reclaimed asphalt pavement, (2) reducing the asphalt production temperature, and (3) prolonging the service life of the pavement. Environmental impact assessment of these methods is necessary to be able to compare these approaches and understand better the ability to reduce the environmental impact during the life cycle of the road pavement. Attention should be drawn to the possible shift in environmental impact between various life cycle stages, e.g., raw material production, asphalt production, or waste treatment. Life cycle assessment is necessary to adequately assess the environmental impact of these approaches over the entire service life of the bituminous pavement. The three approaches and their implementation in the road sector in Flanders (region in Belgium) are described and the main findings from life cycle assessment studies on these subjects are discussed. It was found from the review that using reclaimed asphalt pavement in new bituminous mixtures might yield significant environmental gains. The environmental impact of the application of warm mix asphalt technologies, on the other hand, depends on the technique used. - Highlights: • Recycling, lower production temperature and durability of asphalt are investigated. • The use of RAP in new asphalt mixtures yields significant environmental advantages. • It would be beneficial to allow RAP in asphalt mixtures for wearing courses. • The use of particular additives might counteract the environmental gain from WMA. • The service life and the environmental data source influence the LCA results.

Recyclability of Concrete Pavement Incorporating High Volume of Fly Ash

Science.gov (United States)

Yoshitake, Isamu; Ishida, Takeo; Fukumoto, Sunao

2015-01-01

Recyclable concrete pavement was made from fly ash and crushed limestone sand and gravel as aggregates so that the concrete pavement could be recycled to raw materials for cement production. With the aim to use as much fly ash as possible for the sustainable development of society, while achieving adequate strength development, pavement concrete having a cement-replacement ratio of 40% by mass was experimentally investigated, focusing on the strength development at an early age. Limestone powder was added to improve the early strength; flexural strength at two days reached 3.5 MPa, the minimum strength for traffic service in Japan. The matured fly ash concrete made with a cement content of 200 kg/m3 achieved a flexural strength almost equal to that of the control concrete without fly ash. Additionally, Portland cement made from the tested fly ash concrete was tested to confirm recyclability, with the cement quality meeting the Japanese classification of ordinary Portland cement. Limestone-based recyclable fly ash concrete pavement is, thus, a preferred material in terms of sustainability. PMID:28793518

Recyclability of Concrete Pavement Incorporating High Volume of Fly Ash.

Science.gov (United States)

Yoshitake, Isamu; Ishida, Takeo; Fukumoto, Sunao

2015-08-21

Recyclable concrete pavement was made from fly ash and crushed limestone sand and gravel as aggregates so that the concrete pavement could be recycled to raw materials for cement production. With the aim to use as much fly ash as possible for the sustainable development of society, while achieving adequate strength development, pavement concrete having a cement-replacement ratio of 40% by mass was experimentally investigated, focusing on the strength development at an early age. Limestone powder was added to improve the early strength; flexural strength at two days reached 3.5 MPa, the minimum strength for traffic service in Japan. The matured fly ash concrete made with a cement content of 200 kg/m3 achieved a flexural strength almost equal to that of the control concrete without fly ash. Additionally, Portland cement made from the tested fly ash concrete was tested to confirm recyclability, with the cement quality meeting the Japanese classification of ordinary Portland cement. Limestone-based recyclable fly ash concrete pavement is, thus, a preferred material in terms of sustainability.

Development of superior asphalt recycling agents. Phase 1, Technical feasibility. Final technical progress report

Energy Technology Data Exchange (ETDEWEB)

Bullin, J.A.; Davison, R.R.; Glover, C.J.; Chaffin, J.; Liu, M.; Madrid, R.

1997-07-01

After an introduction and a literature survey in Chap. 1, Chap. 2 describes the tasks, together with objectives and important results obtained for each task throughout the entire project. Chaps. 3 thru 7 detail work in developing a qualitative and quantitative knowledge of asphalt oxidation, composition dependence of asphalt properties, and guidelines for producing superior asphalt binders through composition control. They also detail the development of a kinetic model for asphalt oxidative aging and present an understanding of the composition dependence of asphalt oxidation as well as other performance-related properties. Chaps. 8 and 9 compare the aging performance of recycled blends produced using commercial recycling agents and industrial supercritical fractions as rejuvenating agents. Oxidative aging of the recycled blends were evaluated along with the performance of the recycled blends in terms of the strategic highway research program performance grading procedure. Chap. 10 summarizes the work completed in the areas of processing schemes development, projection updates, and scale-up and commercialization plans.

An evaluation of the efficiency of compartmented alginate fibres encapsulating a rejuvenator as an asphalt pavement healing system

NARCIS (Netherlands)

Tabaković, Amir; Karač, Aleksandar; Schlangen, H.E.J.G.

2017-01-01

This paper explores the potential methods for evaluating a healing system for asphalt pavements. The healing system under investigation involves compartmented calcium-alginate fibres encapsulating an asphalt binder healing agent (rejuvenator). This system presents a novel method of incorporating

Effects of Asphalt Mix Design Properties on Pavement Performance: A Mechanistic Approach

Directory of Open Access Journals (Sweden)

Ahmad M. Abu Abdo

2016-01-01

Full Text Available The main objective of this study was to investigate the effects of hot mix asphalt material properties on the performance of flexible pavements via mechanistic approach. 3D Move Analysis software was utilized to determine rutting and cracking distresses in an asphalt concrete (AC layer. Fourteen different Superpave mixes were evaluated by utilizing results of the Dynamic Modulus (|E⁎| Test and the Dynamic Shear Modulus (|G⁎| Test. Results showed that with the increase of binder content, the tendency of rutting in AC layer increased. However, with the increase of binder content, the cracking of AC layer lessened. Furthermore, when different binder grades were evaluated, results showed that with the increase of the upper binder grade number, rutting decreased, and with the increase of the lower binder grade number, rutting increased. Furthermore, analysis showed that with the increase of the lower binder grade number, higher percent of bottom up cracks would result. As a result of the analysis, binder grade should not be solely considered for cracking in AC layer; binder content and aggregate structure play a big role. Finally, results illustrated that the mechanistic approach is a better tool to determine the performance of asphalt pavement than commonly used methods.

Forensic study into the causes of premature failures in asphalt pavements in Tanzania

CSIR Research Space (South Africa)

Anochie-Boateng, Joseph

2015-11-01

Full Text Available Tanzania is faced with challenges of premature failures in roads and highways. Some asphalt pavements fail prematurely in less than five years of their expected 20 years design life cycle. These failures have been identified as mostly permanent...

Performance Evaluation of Hot Mix Asphalt with Different Proportions of RAP Content

Science.gov (United States)

Kamil Arshad, Ahmad; Awang, Haryati; Shaffie, Ekarizan; Hashim, Wardati; Rahman, Zanariah Abd

2018-03-01

Reclaimed Asphalt Pavement (RAP) is old asphalt pavement that has been removed from a road by milling or full depth removal. The use of RAP in hot mix asphalt (HMA) eliminates the need to dispose old asphalt pavements and conserves asphalt binders and aggregates, resulting in significant cost savings and benefits to society. This paper presents a study on HMA with different RAP proportions carried out to evaluate the volumetric properties and performance of asphalt mixes containing different proportions of RAP. Marshall Mix Design Method was used to produce control mix (0% RAP) and asphalt mixes containing 15% RAP, 25% RAP and 35% RAP in accordance with Specifications for Road Works of Public Works Department, Malaysia for AC14 dense graded asphalt gradation. Volumetric analysis was performed to ensure that the result is compliance with specification requirements. The resilient modulus test was performed to measure the stiffness of the mixes while the Modified Lottman test was conducted to evaluate the moisture susceptibility of these mixes. The Hamburg wheel tracking test was used to evaluate the rutting performance of these mixes. The results obtained showed that there were no substantial difference in Marshall Properties, moisture susceptibility, resilient modulus and rutting resistance between asphalt mixes with RAP and the control mix. The test results indicated that recycled mixes performed as good as the performance of conventional HMA in terms of moisture susceptibility and resilient modulus. It is recommended that further research be carried out for asphalt mixes containing more than 35% RAP material.

Performance Evaluation of Hot Mix Asphalt with Different Proportions of RAP Content

Directory of Open Access Journals (Sweden)

Kamil Arshad Ahmad

2018-01-01

Full Text Available Reclaimed Asphalt Pavement (RAP is old asphalt pavement that has been removed from a road by milling or full depth removal. The use of RAP in hot mix asphalt (HMA eliminates the need to dispose old asphalt pavements and conserves asphalt binders and aggregates, resulting in significant cost savings and benefits to society. This paper presents a study on HMA with different RAP proportions carried out to evaluate the volumetric properties and performance of asphalt mixes containing different proportions of RAP. Marshall Mix Design Method was used to produce control mix (0% RAP and asphalt mixes containing 15% RAP, 25% RAP and 35% RAP in accordance with Specifications for Road Works of Public Works Department, Malaysia for AC14 dense graded asphalt gradation. Volumetric analysis was performed to ensure that the result is compliance with specification requirements. The resilient modulus test was performed to measure the stiffness of the mixes while the Modified Lottman test was conducted to evaluate the moisture susceptibility of these mixes. The Hamburg wheel tracking test was used to evaluate the rutting performance of these mixes. The results obtained showed that there were no substantial difference in Marshall Properties, moisture susceptibility, resilient modulus and rutting resistance between asphalt mixes with RAP and the control mix. The test results indicated that recycled mixes performed as good as the performance of conventional HMA in terms of moisture susceptibility and resilient modulus. It is recommended that further research be carried out for asphalt mixes containing more than 35% RAP material.

Numerical Study of Tire Hydroplaning Based on Power Spectrum of Asphalt Pavement and Kinetic Friction Coefficient

OpenAIRE

Shengze Zhu; Xiuyu Liu; Qingqing Cao; Xiaoming Huang

2017-01-01

Hydroplaning is a driving phenomenon threating vehicle’s control stability and safety. It happens when tire rolls on wet pavement with high speed that hydrodynamic force uplifts the tire. Accurate numerical simulation to reveal the mechanism of hydroplaning and evaluate the function of relevant factors in this process is significant. In order to describe the friction behaviors of tire-pavement interaction, kinetic friction coefficient curve of tire rubber and asphalt pavement was obtained by ...

Mechanical performance assessment of half warm recycled asphalt mixes containing up to 100 % RAP

International Nuclear Information System (INIS)

Lizárraga, J. M.; Jiménez del Barco-Carrión, A.; Ramírez, A.; Díaz, P.; Moreno-Navarro, F.; Rubio, M.C.

2017-01-01

The use of Half Warm Mixes with high Reclaimed Asphalt content (HWMRA) has the potential to generate significant environmental advantages such as the reduction in consumption of natural resources and the emission of gases into the atmosphere. This paper therefore focuses on demonstrating the viability of using these types of mixes in wearing courses. For this purpose, an HWMRA with 70 % and 100 % Reclaimed Asphalt Pavement (RAP) and emulsion were designed in the laboratory. The performance of the mixes was then assessed and compared with that of conventional Hot Mix Asphalt. In a second stage, the mixes were manufactured in-plant, and laid and compacted in an Accelerated Pavement Test track. The cores were then extracted and tested for stiffness modulus and resistance to fatigue. The results from the tests conducted with both the laboratory specimens and the cores showed that the performance of HWMRA is comparable to that of HMA. These findings encourage greater confidence in promoting the use of these types of sustainable asphalt mixes. [es

Mechanical performance assessment of half warm recycled asphalt mixes containing up to 100 % RAP

Directory of Open Access Journals (Sweden)

J. M. Lizárraga

2017-07-01

Full Text Available The use of Half Warm Mixes with high Reclaimed Asphalt content (HWMRA has the potential to generate significant environmental advantages such as the reduction in consumption of natural resources and the emission of gases into the atmosphere. This paper therefore focuses on demonstrating the viability of using these types of mixes in wearing courses. For this purpose, an HWMRA with 70 % and 100 % Reclaimed Asphalt Pavement (RAP and emulsion were designed in the laboratory. The performance of the mixes was then assessed and compared with that of conventional Hot Mix Asphalt. In a second stage, the mixes were manufactured in-plant, and laid and compacted in an Accelerated Pavement Test track. The cores were then extracted and tested for stiffness modulus and resistance to fatigue. The results from the tests conducted with both the laboratory specimens and the cores showed that the performance of HWMRA is comparable to that of HMA. These findings encourage greater confidence in promoting the use of these types of sustainable asphalt mixes.

Extending the Service Life of Pavements

Science.gov (United States)

Gschwendt, Ivan

2018-03-01

The cost of road construction and expenditures on the maintenance of pavements, i.e., their whole life cost, represents a lot of money. The paper describes a procedure for a pavement management system with degradation models and estimates the length of time for the rehabilitation of an asphalt pavement. Using a theory of pavement mechanics, we calculated the stresses and strains on the layers of two pavement models. High modulus asphalt concrete, an asphalt mix with a high binder content, and an asphalt mix with binder modifications are new road building materials. Prolonging the time for the rehabilitation of pavements is possible.

Investigation of using steel slag in hot mix asphalt for the surface course of flexible pavements

Science.gov (United States)

Nguyen, Hien Q.; Lu, Dai X.; Le, Son D.

2018-04-01

The rapid development of heavy industry in Vietnam leads to the establishments of steel industry. Steel slag, a by-product of steelwork industry, under Vietnamese’s law, was considered as a deleterious solid waste which needed to be processed and landfilled. However, this has changed recently, and steel slag is now seen as a normal or non-deleterious solid waste, and has been studied for reuse in the construction industry. In this study, steel slag was used, as a replacement for mineral aggregate, in hot mix asphalt. Two hot mix asphalt mixtures with an equivalent nominal aggregate size of 12.5 (C12.5) and 19 mm (C19) were produced using steel slag. In addition, one conventional hot mix asphalt mixture of C19 was produced using mineral aggregate for comparison purpose. Investigation in laboratory condition and trial sections was carried out on Marshall tests, surface roughness, skid resistance, and modulus of the pavement before and after applying a new surface course of hot mix asphalt. The study showed that all steel slag asphalt mixtures passed the Marshall stability and flow test requirements. The skid resistance of steel slag hot mix asphalt mixtures for the surface course satisfied the Vietnamese specification for asphalt. Moreover, the pavement sections with the surface course of steel slag hot mix asphalt showed a considerable higher modulus than that of the conventional one. Only the roughness of the surface course paved with C19 did not pass the requirement of the specification.

Use of rubber asphalt binder with graded aggregate for seal coats

Energy Technology Data Exchange (ETDEWEB)

1979-01-01

It has been known that incorporating rubber particles into asphalt can improve highway pavement performance. This paper describes a test program on pavement construction using asphalts containing recycled rubber. During the summer 1978, eight test sections were constructed in parts of the Saskatchewan road system to evaluate seal coats using rubber-asphalt as a binder membrane and a graded aggregate as protective cover. Test sections were chosen to represent typical road surface types and different states of repair for each type. These types included prime subgrade, cold-mix on subgrade, primed granular base course, asphaltic concrete on granular base, and full depth asphaltic concrete. Problems with construction materials, techniques, and equipment are discussed. Performance and economics were evaluated to determine whether low cost cold mix and current seal coat surfaces could be replaced successfully and economically by this method of construction. It was shown that use of reclaimed rubber for rubberized asphalt seal coats on Saskatechewan highways is a practical construction application. The economic justification for rubber asphalt seals will be determined after a full assessment of performance. Initial indications are that Saskatchewan graded aggregates are a suitable cover material for the rubberized asphalt membranes used in the trials. 8 refs., 16 figs., 7 tabs.

High-volume recycled materials for sustainable pavement construction.

Science.gov (United States)

2017-05-01

The main objective of this research is to evaluate the feasibility of using high-volume recycled materials for concrete production in rigid pavement. The goal was to replace 50% of the solids with recycled materials and industrial by-products. The pe...

Evaluation of the Pavement Quality Indicator (PQI for the on-site density measurement of asphalt emulsion mixes

Directory of Open Access Journals (Sweden)

Martínez-Echevarría, M. J.

2013-03-01

Full Text Available The Pavement Quality Indicator (PQI is a non-nuclear gauge used for the on-site density measurement of asphalt pavements without the need to extract core samples. Previous studies of hot asphalt mixes found that PQI density readings were very similar to laboratory density measurements of pavement cores. This paper describes the first stage of a research project whose objective is to analyze PQI density measurements of mixes manufactured with an asphalt emulsion binder. The PQI density variability for such mixes was verified and compared with the results obtained with other on-site methods for measuring pavement density.

El equipo Pavement Quality Indicator es un dispositivo para la determinación de densidad in situ en pavimentos asfálticos sin extracción de testigos. Las experiencias con este equipo en mezclas bituminosas en caliente, recogidas en diferentes fuentes bibliográficas, muestran que las densidades medidas in situ con el PQI son muy similares a las obtenidas mediante la extracción de testigos. En este artículo se expone la primera etapa de un proyecto de investigación que tiene por objeto analizar los resultados de mediciones efectuadas con PQI en mezclas bituminosas donde se utiliza emulsión asfáltica como ligante. Se comprueba la variabilidad de la densidad obtenida con el equipo para este tipo de mezclas, y se comparan los resultados con otros métodos de medida de densidad in situ.

Flexibl Pavement Analysis Considering Temperature Profile and Anisotropy Behavior in Hot Mix Asphalt Layer

Directory of Open Access Journals (Sweden)

Choi Joonho

2011-12-01

Full Text Available A three Dimensional finite element model (FEM incorporating the anisotropic properties and temperature profile of hot mix asphalt (HMA pavement was developed to predict the structural responses of HMA pavement subject to heavy loads typically encountered in the field. In this study, ABAQUS was adopted to model the stress and strain relationships within the pavement structure. The results of the model were verified using data collected from the Korean Highway Corporation Test Road (KHCTR. The results demonstrated that both the base course and surface course layers follow the anisotropic behavior and the incorporation of the temperature profile throughout the pavement has a substantial effect on the pavement response predictions that impact pavement design. The results also showed that the anisotropy level of HMA and base material can be reduced to as low as 80% and 15% as a result of repeated loading, respectively.

Asphalt Pavement Pothole Detection and Segmentation Based on Wavelet Energy Field

Directory of Open Access Journals (Sweden)

Penghui Wang

2017-01-01

Full Text Available Potholes are one type of pavement surface distresses whose assessment is essential for developing road network maintenance strategies. Existing methods for automatic pothole detection either rely on expensive and high-maintenance equipment or could not segment the pothole accurately. In this paper, an asphalt pavement pothole detection and segmentation method based on energy field is put forward. The proposed method mainly includes two processes. Firstly, the wavelet energy field of the pavement image is constructed to detect the pothole by morphological processing and geometric criterions. Secondly, the detected pothole is segmented by Markov random field model and the pothole edge is extracted accurately. This methodology has been implemented in a MATLAB prototype, trained, and tested on 120 pavement images. The results show that it can effectively distinguish potholes from cracks, patches, greasy dirt, shadows, and manhole covers and accurately segment the pothole. For pothole detection, the method reaches an overall accuracy of 86.7%, with 83.3% precision and 87.5% recall. For pothole segmentation, the overlap degree between the extracted pothole region and the original pothole region is mostly more than 85%, which accounts for 88.6% of the total detected pavement pothole images.

Strain transfer analysis of optical fiber based sensors embedded in an asphalt pavement structure

International Nuclear Information System (INIS)

Wang, Huaping; Xiang, Ping

2016-01-01

Asphalt pavement is vulnerable to random damage, such as cracking and rutting, which can be proactively identified by distributed optical fiber sensing technology. However, due to the material nature of optical fibers, a bare fiber is apt to be damaged during the construction process of pavements. Thus, a protective layer is needed for this application. Unfortunately, part of the strain of the host material is absorbed by the protective layer when transferring the strain to the sensing fiber. To account for the strain transfer error, in this paper a theoretical analysis of the strain transfer of a three-layered general model has been carried out by introducing Goodman’s hypothesis to describe the interfacial shear stress relationship. The model considers the viscoelastic behavior of the host material and protective layer. The effects of one crack in the host material and the sensing length on strain transfer relationship are been discussed. To validate the effectiveness of the strain transfer analysis, a flexible asphalt-mastic packaged distributed optical fiber sensor was designed and tested in a laboratory environment to monitor the distributed strain and appearance of cracks in an asphalt concrete beam at two different temperatures. The experimental results indicated that the developed strain transfer formula can significantly reduce the strain transfer error, and that the asphalt-mastic packaged optical fiber sensor can successfully monitor the distributed strain and identify local cracks. (paper)

Strain transfer analysis of optical fiber based sensors embedded in an asphalt pavement structure

Science.gov (United States)

Wang, Huaping; Xiang, Ping

2016-07-01

Asphalt pavement is vulnerable to random damage, such as cracking and rutting, which can be proactively identified by distributed optical fiber sensing technology. However, due to the material nature of optical fibers, a bare fiber is apt to be damaged during the construction process of pavements. Thus, a protective layer is needed for this application. Unfortunately, part of the strain of the host material is absorbed by the protective layer when transferring the strain to the sensing fiber. To account for the strain transfer error, in this paper a theoretical analysis of the strain transfer of a three-layered general model has been carried out by introducing Goodman’s hypothesis to describe the interfacial shear stress relationship. The model considers the viscoelastic behavior of the host material and protective layer. The effects of one crack in the host material and the sensing length on strain transfer relationship are been discussed. To validate the effectiveness of the strain transfer analysis, a flexible asphalt-mastic packaged distributed optical fiber sensor was designed and tested in a laboratory environment to monitor the distributed strain and appearance of cracks in an asphalt concrete beam at two different temperatures. The experimental results indicated that the developed strain transfer formula can significantly reduce the strain transfer error, and that the asphalt-mastic packaged optical fiber sensor can successfully monitor the distributed strain and identify local cracks.

PECULIAR FEATURES OF HEAT-HUMIDITY MODE PERTAINING TO POROUS LAYERS OF ASPHALT CONCRETE PAVEMENTS

Directory of Open Access Journals (Sweden)

V. Verenko

2012-01-01

Full Text Available The paper presents results of experimental investigations and points out the fact that conventional approaches to design and calculations of road pavements that presuppose application of porous asphalt concrete on compact bedding can cause some deformations and destructions initiated due to humidity migration in large internal material pores and lead to material destruction during warm season of the year when water is characterized by high activity. Such processes result in bitumen washing-out, white spot occurrence on the pavement and quick destruction of the pavement.The paper proposes to reconsider existing approaches to design and calculation of road pavements, estimation of reliability and service-ability levels of the applied construction materials. In particular it is necessary to calculate a road pavement with respect to thermo-physical action while excluding condensate and humidity accumulation in porous materials. 

Tire wear emissions for asphalt rubber and Portland cement concrete pavement surfaces.

Science.gov (United States)

2006-04-01

Since 1990, it has been the policy of the State of Arizona that the recycling and reuse of : waste tires are the highest priority. The Arizona Department of Transportation (ADOT) : has long supported the use of recycled waste tire rubber in asphalt r...

Effect of tack coat application on interlayer shear strength of asphalt pavement: A state-of-the-art review based on application in the United States

Directory of Open Access Journals (Sweden)

Weiguang Zhang

2017-09-01

Full Text Available The effect of tack coat application on pavement interlayer shear strength attracts strong interest during asphalt paving. Given its extensive use, tack coat is known to behave as a bond material to reduce pavement distresses such as slippage crack. The effectiveness of tack coat in increasing shear strength may be affected by multiple factors, such as tack coat material, test condition, pavement surface condition, and moisture. This article is a literature review focus on how the interlayer shear strength varied when relevant influential factors are changing. Review results indicate that the interlayer shear strength increased with the decreased test temperature, increased traffic load (within design limit, and increased test confinement pressure. Additionally, the milled pavement surface always has higher shear strength then the non-milled pavement surface. It is also found that laboratory-prepared specimens resulted in higher interlayer shear strength than field pavement cores. The effect of other factors on tack coat application may follow different trends depending on mix type and existing pavement condition. For instance, optimum tack coat rate that corresponds to peak shear strength is widely reported, while it is also found that tack coat does not greatly affect shear strength on dry, clean and milled pavement surface. Furthermore, shear strength reduced when mixture is designed with high percentage of air voids or coarse aggregate structure, such as porous asphalt and stone mastic asphalt (SMA mixtures. More findings and recommendations can be found in this paper. Keywords: Tack coat, Interlayer shear strength, Asphalt pavement, Temperature, Milling, Mixture type

Linking asphalt binder fatigue to asphalt mixture fatigue performance using viscoelastic continuum damage modeling

Science.gov (United States)

Safaei, Farinaz; Castorena, Cassie; Kim, Y. Richard

2016-08-01

Fatigue cracking is a major form of distress in asphalt pavements. Asphalt binder is the weakest asphalt concrete constituent and, thus, plays a critical role in determining the fatigue resistance of pavements. Therefore, the ability to characterize and model the inherent fatigue performance of an asphalt binder is a necessary first step to design mixtures and pavements that are not susceptible to premature fatigue failure. The simplified viscoelastic continuum damage (S-VECD) model has been used successfully by researchers to predict the damage evolution in asphalt mixtures for various traffic and climatic conditions using limited uniaxial test data. In this study, the S-VECD model, developed for asphalt mixtures, is adapted for asphalt binders tested under cyclic torsion in a dynamic shear rheometer. Derivation of the model framework is presented. The model is verified by producing damage characteristic curves that are both temperature- and loading history-independent based on time sweep tests, given that the effects of plasticity and adhesion loss on the material behavior are minimal. The applicability of the S-VECD model to the accelerated loading that is inherent of the linear amplitude sweep test is demonstrated, which reveals reasonable performance predictions, but with some loss in accuracy compared to time sweep tests due to the confounding effects of nonlinearity imposed by the high strain amplitudes included in the test. The asphalt binder S-VECD model is validated through comparisons to asphalt mixture S-VECD model results derived from cyclic direct tension tests and Accelerated Loading Facility performance tests. The results demonstrate good agreement between the asphalt binder and mixture test results and pavement performance, indicating that the developed model framework is able to capture the asphalt binder's contribution to mixture fatigue and pavement fatigue cracking performance.

Environmental and functional benefits and trade-offs of hot in-place recycling treatment techniques : final project report.

Science.gov (United States)

2016-12-01

Surface recycling is suitable for pavements with minor cracks limited to 25-50 mm in depth. Hot-in-place recycling (HIR) process includes drying and heating the upper layers, scarifying the soft asphalt, mixing the scarified material with a rejuvenat...

Performance on Water Stability of Cement-Foamed Asphalt Cold Recycled Mixture

OpenAIRE

Li Junxiao; Fu Wei; Zang Hechao

2018-01-01

Through designing the mixture proportion of foamed asphalt cold in-place recycled mixture combined with the water stability experiment, it shows that the addition of cement can obviously improve foamed asphalt mixture’s water stability and the best cement admixture is between 1% ~ 2%; Using digital imaging microscope and SEM technology, the mechanism of increasing on the intensity of foamed asphalt mixture resulted by adding cement was analyzed. It revealed that the cement hydration products ...

Warm mix asphalt : final report.

Science.gov (United States)

2014-11-01

The performance of pavements constructed using warm mix asphalt (WMA) technology were : compared to the performance of conventional hot mix asphalt (HMA) pavements placed on the : same project. Measurements of friction resistance, rutting/wear, ride ...

Environmental performance and mechanical analysis of concrete containing recycled asphalt pavement (RAP) and waste precast concrete as aggregate.

Science.gov (United States)

Erdem, Savaş; Blankson, Marva Angela

2014-01-15

The overall objective of this research project was to investigate the feasibility of incorporating 100% recycled aggregates, either waste precast concrete or waste asphalt planning, as replacements for virgin aggregates in structural concrete and to determine the mechanical and environmental performance of concrete containing these aggregates. Four different types of concrete mixtures were designed with the same total water cement ratio (w/c=0.74) either by using natural aggregate as reference or by totally replacing the natural aggregate with recycled material. Ground granulated blast furnace slag (GGBS) was used as a mineral addition (35%) in all mixtures. The test results showed that it is possible to obtain satisfactory performance for strength characteristics of concrete containing recycled aggregates, if these aggregates are sourced from old precast concrete. However, from the perspective of the mechanical properties, the test results indicated that concrete with RAP aggregate cannot be used for structural applications. In terms of leaching, the results also showed that the environmental behaviour of the recycled aggregate concrete is similar to that of the natural aggregate concrete. Copyright © 2013 Elsevier B.V. All rights reserved.

Performance of I-57 recycled concrete pavements.

Science.gov (United States)

2009-01-01

In 1986-1987 the Illinois Department of Transportation (IDOT) constructed a demonstration project on I-57 near Effingham, Illinois to evaluate the viability : of recycling an existing jointed reinforced concrete pavement for use as its primary aggreg...

Measurements of the Stiffness and Thickness of the Pavement Asphalt Layer Using the Enhanced Resonance Search Method

Directory of Open Access Journals (Sweden)

Nur Mustakiza Zakaria

2014-01-01

Full Text Available Enhanced resonance search (ERS is a nondestructive testing method that has been created to evaluate the quality of a pavement by means of a special instrument called the pavement integrity scanner (PiScanner. This technique can be used to assess the thickness of the road pavement structure and the profile of shear wave velocity by using the principle of surface wave and body wave propagation. In this study, the ERS technique was used to determine the actual thickness of the asphaltic pavement surface layer, while the shear wave velocities obtained were used to determine its dynamic elastic modulus. A total of fifteen locations were identified and the results were then compared with the specifications of the Malaysian PWD, MDD UKM, and IKRAM. It was found that the value of the elastic modulus of materials is between 3929 MPa and 17726 MPa. A comparison of the average thickness of the samples with the design thickness of MDD UKM showed a difference of 20 to 60%. Thickness of the asphalt surface layer followed the specifications of Malaysian PWD and MDD UKM, while some of the values of stiffness obtained are higher than the standard.

Design Method for Proportion of Cement-Foamed Asphalt Cold Recycled Mixture

OpenAIRE

Li Junxiao; Fu Wei; Zang Hechao

2018-01-01

Through foaming experiment of Zhongtai AH-70 asphalt, the best foaming temperature water consumption and influence factors of foamed asphalt’s foaming features are determined; By designing the proportion of foamed asphalt cold in-place recycled mixture combined with the water stability experiment, for this mixture the best foamed asphalt addition is 3%, and proportion of the mixture is RAP: fine aggregate: cement=75:23:2. Using SEM technology, the mechanism of increasing on the intensity of f...

Characterization and Modeling of Recycled Pavement Sections

Science.gov (United States)

2017-12-01

Because of its documented cost and environmental benefits, cold central plant recycling (CCPR) has attracted the interest of local and state departments of transportation. In 2015 two test pavement sections with CCPR as base layers were constructed a...

Three-dimensional modelling of sound absorption in porous asphalt pavement for oblique incident waves

NARCIS (Netherlands)

Bezemer-Krijnen, Marieke; Wijnant, Ysbrand H.; de Boer, Andries; Glorieux, C.

2015-01-01

Sound absorption of porous asphalt pavements is an important property when reducing tyre-road noise. A hybrid model has been developed to predict the sound absorption of porous roads. This model is a combination of an analytical analysis of the sound eld and a numerical approach, including both the

Evaluating life cycle costs of perpetual pavements in China using operational pavement management system

Directory of Open Access Journals (Sweden)

Saud A. Sultan

2016-10-01

Full Text Available Highway transportation is considered as vital factor in China’s economic growth; many high grade highways have been constructed in China during the last decades. The research and application of perpetual asphalt pavement (PP technology have been deployed in China since 2000. The semi-rigid pavement has been normally considered as typical pavement of high class highways in the design according to the Chinese experience. The objective of this research is to evaluate the performance of different Chinese perpetual pavements using operational pavement management system and to examine its suitability for use in the design and construction of more economical and durable pavements. It has been found that the use of thin asphalt layers over semi-rigid pavement foundation in PP structure will create more sustainable, economical, and durable PP structures in comparison with typical thick asphalt layers PP structures.

Structural Design and Economic Evaluation of Roller Compacted Concrete Pavement with Recycled Aggregates

Science.gov (United States)

Abut, Yavuz; Taner Yildirim, Salih

2017-10-01

Using recycled aggregates in the concrete offers advantages in many areas such as waste management, energy save and natural resources, conservation of ecological balance, low CO2 emissions, and users are encouraged in this regard to use these materials. In this study, the profit / loss account arising in the structural design phase was investigated when Reclaimed Asphalt Pavement (RAP), which is limited to use in Roller Compacted Concrete (RCC) pavements, was used as coarse aggregate. RAP materials were used as coarse aggregates by the levels of 0%, 15% and 20% and mechanical properties such as compressive strength, flexural strength, splitting tensile strength and modulus of elasticity were investigated. In the last stage, the mechanical properties obtained from these experimental studies were entered into KENSLABS software as input, and the slab layer thicknesses were determined according to three different subgrade conditions and a certain fatigue criterion. According to the results, it has been determined that the use of RAP at a level of 20% is a serious reducing effect on mechanical properties and and the use of RAP at a level of 15% does not bring a great economic benefit but it is reasonable to use it as coarse aggregate in RCC mixes in consideration of environmental effects.

Advanced self-healing asphalt composites in the pavement performance field: mechanisms at the nano level and new repairing methodologies.

Science.gov (United States)

Agzenai, Yahya; Pozuelo, Javier; Sanz, Javier; Perez, Ignacio; Baselga, Juan

2015-01-01

In an effort to give a global view of this field of research, in this mini-review we highlight the most recent publications and patents focusing on modified asphalt pavements that contain certain reinforcing nanoparticles which impart desirable thermal, electrical and mechanical properties. In response to the increasing cost of asphalt binder and road maintenance, there is a need to look for alternative technologies and new asphalt composites, able to self-repair, for preserving and renewing the existing pavements. First, we will focus on the self-healing property of asphalt, the evidences that support that healing takes place immediately after the contact between the faces of a crack, and how the amount of healing can be measured in both the laboratory and the field. Next we review the hypothetical mechanisms of healing to understand the material behaviour and establish models to quantify the damage-healing process. Thereafter, we outline different technologies, nanotechnologies and methodologies used for self-healing paying particular attention to embedded micro-capsules, new nano-materials like carbon nanotubes and nano-fibres, ionomers, and microwave and induction heating processes.

Performance Characteristic of Cold Recycled Mixture with Asphalt Emulsion and Chemical Additives

Directory of Open Access Journals (Sweden)

Shaowen Du

2015-01-01

Full Text Available Three types of chemical additives were used to modify asphalt emulsion recycled mixture. These chemical additives include composite Portland cement (CPC, hydrated lime (HL, and a combination of hydrated lime and ground-granulated blast-furnace slag (GGBF. The influence of different additives on the recycled mixture performance was investigated by volumetric and strength tests, moisture susceptibility test, rutting resistance test, and low temperature bending test. To better understand its performance characteristic, the microstructure images of the recycled mixture were observed by environmental scanning electron microscope (ESEM. Test results demonstrate that the performance improvement of the emulsion recycled mixture depends on the types and content of chemical additives. Several recommendations are presented for the selection of chemical materials. Based on ESEM image analysis, the interface bonding mechanism is proposed to explain the performance characteristic of the recycled mixture with asphalt emulsion and cementitious materials.

Effect of hydrated lime and cement on moisture damage of recycled mixtures with foamed bitumen and emulsion

OpenAIRE

Nosetti, R.A.; Pérez Jiménez, Félix Edmundo; Martínez Reguero, Adriana Haydée; Miró Recasens, José Rodrigo

2016-01-01

Cold recycling with foamed bitumen can be used as a sustainable and cost-effective rehabilitation technique. This paper focuses on the evaluation of the resistance to the water action in mixtures with reclaimed asphalt pavement (RAP) and foamed bitumen by means of indirect tensile test, comparing the effect of two active fillers: cement and hydrated lime. Additionally, mixtures recycled with RAP and asphalt emulsions were also tested in order to compare the response of both technologies. Resu...

Full depth bituminous recycling of I-70, Thomas County, Kansas

Science.gov (United States)

2004-01-01

In 1990, 13 full depth asphalt pavement test sections were built on a portion of I-70 in Thomas County, Kansas. Various combinations of hot mix and cold recycle mixes with different additives were used to build the test sections. Two of the test sect...

Dismantling techniques and recycling or other end-of-life treatments of other materials not commonly reused in roads

OpenAIRE

Batista, F. A.; Antunes, M. L.; Santos, C.

2009-01-01

Este registo pertence ao Repositório Científico do LNEC The interest of recycling of waste, industrial by-products and other road materials for pavement construction and rehabilitation has been generally growing in Portugal, for the last 10 years. Among the several types of wastes, there’s been a great interest in using recycled tyres as a raw material to be incorporated in asphalt paving mixtures. The first significant experience with asphalt rubber, manufactured by the wet...

Preparation and thermal properties of mineral-supported polyethylene glycol as form-stable composite phase change materials (CPCMs) used in asphalt pavements.

Science.gov (United States)

Jin, Jiao; Lin, Feipeng; Liu, Ruohua; Xiao, Ting; Zheng, Jianlong; Qian, Guoping; Liu, Hongfu; Wen, Pihua

2017-12-05

Three kinds of mineral-supported polyethylene glycol (PEG) as form-stable composite phase change materials (CPCMs) were prepared to choose the most suitable CPCMs in asphalt pavements for the problems of asphalt pavements rutting diseases and urban heat islands. The microstructure and chemical structure of CPCMs were characterized by SEM, FT-IR and XRD. Thermal properties of the CPCMs were determined by TG and DSC. The maximum PEG absorption of diatomite (DI), expanded perlite (EP) and expanded vermiculite (EVM) could reach 72%, 67% and 73.6%, respectively. The melting temperatures and latent heat of CPCMs are in the range of 52-55 °C and 100-115 J/g, respectively. The results show that PEG/EP has the best thermal and chemical stability after 100 times of heating-cooling process. Moreover, crystallization fraction results show that PEG/EP has slightly higher latent heats than that of PEG/DI and PEG/EVM. Temperature-adjusting asphalt mixture was prepared by substituting the fine aggregates with PEG/EP CPCMs. The upper surface maximum temperature difference of temperature-adjusting asphalt mixture reaches about 7.0 °C in laboratory, and the surface peak temperature reduces up to 4.3 °C in the field experiment during a typical summer day, indicating a great potential application for regulating pavement temperature field and alleviating the urban heat islands.

Recycling of rubber tires in asphalt paving materials

Energy Technology Data Exchange (ETDEWEB)

Piggott, M.R.; Woodhams, R.T.

1979-01-01

It has been known that the addition of rubber to asphalt used in paving will produced markedly superior road surfaces. Partly because of cost and because of the nonconventional paving techniques necessary, rubber has been largely ignored as a practical paving additive except in special cases. However, the large accumulation of old tires existing today provides a ready source for suitable rubber. If ground into a fine powder, this rubber can be mixed in a conventional pug mill along with sand, stone and asphalt to produce a hot mix which can be aplied in the normal manner without any special techniques. The extra cost of such modification is only 1% of a typical paving contract, whereas the advantages include lower maintenance cost, more durable road surface, and elimination of unwanted waste tires. This report has been prepared to assist civic and other authorities in the development of improved road surfacing formulations through the reuse of old tires. It includes the results of paving trials in Toronto and laboratory evaluations. These tests show that the addition of powdered rubber to asphalt paving materials markedly improves the durability and crack resistance, particularly at low temperatures. Additives in the rubber impart good strength retention in the presence of moisture. The toughness increases with age due to a slow interaction of the rubber with the asphalt which is accompanied by an increase in viscosity. As a result, performance is also enhanced at high temperatures and helps to minimize pavement distortions due to hot weather and traffic. 16 refs., 18 figs., 2 tabs.

STUDY OF ASPHALT BINDER OIL RESIDUE AND MUNICIPAL SOLID WASTE ASH TO BE USED IN LOW TRAFFIC PAVEMENTS

Directory of Open Access Journals (Sweden)

Michéle Dal Toé Casagrande

2014-12-01

Full Text Available The great generation of urban solid has been a concern in several countries. This work presents a study with two materials: the asphalt binder oil residue accumulated in the bottom of asphalt tanks and the municipal solid waste ash, to be used, respectively, as a substitute of conventional binder in asphalt mixtures and for soil stabilization in pavements base layers. Were evaluated properties as the mechanical behavior of the mixtures through experimental tests. The results show the potential of incorporating these residues for low traffic roads, allowing the construction of low cost roads and an environmental use of the residue.

Recycled Portland cement concrete pavements : Part II, state-of-the art summary.

Science.gov (United States)

1979-01-01

This report constitutes a review of the literature concerning recycling of portland cement concrete pavements by crushing the old pavement and reusing the crushed material as aggregate in a number of applications. A summary of the major projects cond...

Effects of Crumb Rubber Size and Concentration on Performance of Porous Asphalt Mixtures

Directory of Open Access Journals (Sweden)

Altan Cetin

2013-01-01

Full Text Available The purpose of this study is to investigate the effect of size distribution and concentration of crumb rubber on the performance characteristics of porous asphalt mixture. The recycling of scrap tires in asphalt pavements appears as an important alternative providing a large-scale market. The characteristics of bitumen are very important with regard to service life of porous asphalt pavement. The experimental study consists of two main steps. Firstly, the mixture design was performed to determine the optimum bitumen content. In the latter step, the mixtures were modified by dry process using crumb rubber in three different grain size distributions of #4~#20, #20~#200, and #4~#200 and rubber content of 10%, 15%, and 20% as weight of optimum bitumen. The permeability, Cantabro abrasion loss, indirect tensile strength, moisture susceptibility, and resilient modulus tests were carried out on the specimens. Test results show that #20~#200 sized rubber particles reduced air voids and coefficient of permeability, while they increased the Cantabro abrasion loss. In general, increasing the crumb rubber size and content decreased the performance characteristics of the porous asphalt mixtures.

Comparison of renewable oil, recycled oil, and commercial rejuvenating agent derived from crude oil in paving asphalt modification[Includes the CSCE forum on professional practice and career development : 1. international engineering mechanics and materials specialty conference : 1. international/3. coastal, estuarine and offshore engineering specialty conference : 2. international/8. construction specialty conference

Energy Technology Data Exchange (ETDEWEB)

Gordon, C.; Ho, S.; Zanzotto, L. [Calgary Univ., AB (Canada). Schulich School of Engineering

2009-07-01

The asphalt industry relies heavily on crude oil. In response to increasing oil prices, there have been efforts to save money on asphalt by taking harder asphalts, such as recycled asphalt pavement (RAP), and softening them with rejuvenating agents. For asphalt that is to be used in cold climates, softer asphalts are preferred because they will perform better under extreme cold conditions without cracking. This study compared the performance, economic benefits, and environmental benefits of renewable materials, recycled oil and a commercially used rejuvenating agent derived from crude oil. Different oily materials including margarine, Cyclogen L (a crude oil-derived material), a vegetable wax, and recycled cooking oil were used to modify paving asphalt. Their effectiveness at improving the superpave low-temperature performance grade was compared. The samples were all tested using the 2008 AASHTO M320 procedures. The high temperature grades were determined using the dynamic shear rheometer test, and the low-temperature grades were determined using the bending beam rheometer test. The 3 varieties of margarine that were tested were able to improve the low-temperature grade, but they caused a greater depreciation of the high-temperature performance grade than the other materials, and were much more expensive. The best candidate for an effective, economic asphalt softening agent was found to be the recycled cooking oil. It out-performed the Cyclogen L oil in terms of improving the low- temperature performance grade, and was less expensive. 12 refs., 4 tabs., 6 figs.

Thermal and hydraulic analysis of multilayered asphalt pavements as active solar collectors

International Nuclear Information System (INIS)

Pascual-Muñoz, P.; Castro-Fresno, D.; Serrano-Bravo, P.; Alonso-Estébanez, A.

2013-01-01

Highlights: • A new type of asphalt solar collector has been introduced in this paper. • The common pipe network has been replaced for a highly porous asphalt layer. • The use of these collectors contributes to achieve current environmental targets. • Excellent thermal efficiencies have been obtained in the laboratory tests. • Further research is needed to increase the low flow rates achieved. - Abstract: The fulfillment of current environmental aims like reducing fossil fuel consumption or greenhouse gas emissions entails the development of new technologies that enable the use of cleaner, cheaper and renewable energies. Furthermore, the need to improve energy efficiency in buildings encourages scientists and engineers to find new ways of harvesting energy for later uses. The use of asphalt pavements as active solar collectors is introduced in this article. Several authors have studied the use of roads as an energy source before. However, a new technology is presented in which a multilayered pavement with a highly porous middle layer is used instead of a solar collector with an embedded pipe network. These collectors are fully integrated within the road infrastructure and may offer low cost solar energy for water heating. The paper includes a brief comment on the state-of-the-art. Then, a broad methodology is presented in which data, materials and procedures needed to run the tests are fully described. Finally, the results of the laboratory tests are stated and discussed. The prototype used in the laboratory provided excellent thermal efficiency. However, these good results contrast with the low flow rate levels registered during the tests. Thus, although this technology seems to be very promising, new experimental tests should be performed before an effective application is possible

Mechanical Response Analysis of Long-life Asphalt Pavement Structure of Yunluo High-speed on the Semi-rigid Base

Science.gov (United States)

Liu, Feng; Wu, Chuanhai; Xu, Xinquan; Li, Hao; Wang, Zhixiang

2018-01-01

In order to grasp the rule of the strain change of the semi-rigid asphalt pavement structure under the FWD load and provide a reliable theoretical and practical basis for the design of the pavement structure, based on the test section of Guangdong Yunluo expressway, taking FWD as the loading tool, by using the finite element analysis software ANSYS, the internal variation rules of each pavement structural layer were obtained. Based on the results of the theoretical analysis, the measured strain sensor was set up in the corresponding layer of the pavement structure, and the strain test plan was determined. Based on the analysis of the strain data obtained from several structural layers and field monitoring, the rationality of the type pavement structure and the strain test scheme were verified, so as to provide useful help for the design and the maintenance of the pavement structure.

FORECASTING OF DURABILITY OF ASPHALT PAVEMENT ON THE BASIS OF LEVELS OF THEIR VIBRATION LOADING

Directory of Open Access Journals (Sweden)

V. A. Osinovskaya

2015-01-01

Full Text Available The problem of low durability of flexible pavement is one of the most important problems of road economy. For example, the actual service life of asphalt pavement in Russia about 3 … 5 years. The bad condition of highways is an obstacle for the development of the national economy and leads to a significant annual economic losses.At present, this problem has no exact solution. Even at the seeming good road conditions of Europe and America the problem of low durability is no less important in these countries. And this problem becomes more and more actual every year.Our scientific researches allowed to make a hypothesis that the projected of pavements are not have the necessary durability yet not of a stage of designing because in strength calculations did not take into account the vibration of road constructions.Very actual the vibration loading becomes today as is now significantly changed the nature of loading of pavements. As a result the deflections of a pavements are reduced, but the increased vibration of pavements accelerated processes of destruction and significantly reduced durability.The theory of vibration destruction developed by the author allows to adjust the vibration, to form the vibration resistance pavements, and also to forecast a residual life of pavements that will more effectively develop repair actions.

Evaluation of Rutting Performance of Asphalt Mixture with Driving Wheel Pavement Analyzer

Directory of Open Access Journals (Sweden)

Xu Cai

2017-01-01

Full Text Available Rutting is common pavement distress, which leads to lower riding comfort for road users and high maintenance costs. One of the commonly used tests is the simulation test with wheel tracking devices. Here, a new rutting test system has been developed based on the “Driving Wheel Pavement Analyzer” (DWPA to evaluate the rutting performance of asphalt mixtures. This study conducted three types of rutting tests to validate feasibility, reliability, and accuracy of DWPA test. The results indicated that the DWPA test provided more information on ruts and enabled us to distinguish the performance of materials. The CDWPA index is better suited to reflect the rutting resistance of the material, which is highly correlated to the APA rutting index and the rutting test index of China according to the grey relational analysis results.

Investigation on Tensile Strength Ratio (TSR Specimen to Predict Moisture Sensitivity of Asphalt Pavements Mixture and Using Polymer to Reduce Moisture Damage

Directory of Open Access Journals (Sweden)

Mohammed Aziz Hameed Al-Shaybani

2017-05-01

Full Text Available Moisture damage of asphalt concrete is defined as losing the strength and Permanence caused by the active presence of moisture.The most common technique to reduce moisture damage is using modifiers with the asphalt binder or the aggregate.The goal of this study was to explore the effect of various modifiers of polymer on the moisture susceptibility mixture of asphaltic concrete pavement. Modifiers included in this research selected two kinds of polymers Crumb Rubber No 50 (CR No 50 and Methyl Methacrylates (MMA(which are available in the local markets in Iraq and have been used in three percentages for each type. These percentages are (5, 10 and 15% for (CR No 50 and (2.5, 5 and 7.5(% for (MMA.Each type of these polymers is blended with asphalt by wet process at constant blending times for a suitable range of temperatures. The experimental works showed that all polymers modified mixtures have indirect tensile strength higher than control asphalt mixtures, its about (2-15 %, dependent on different type of polymer and polymer concentration under predicted suitable blending time.Test results of indirect tensile strength indicated betterment in modifying the proprieties of mixture, the increased resistance mixture of asphalt concrete pavement versus moisture damage, and reduced the effect of water on asphalt concrete properties. The final result is the addition of (10% CR No 50 and (5% MMA to asphalt mixtures showed an improved mixture of asphalt concrete properties and produced strong mixtures for road construction.One model is predicted for tensile strength ratio [TSR]to estimate the effects of polymer modification on moisture susceptibility mixture of asphalt concrete.

Application of CalME incremental-recursive method to the evaluation of the structural condition as asphalt pavements

International Nuclear Information System (INIS)

Mateos Moreno, A.; Perez Ayuso, J.; Cadavid Jauregui, B.; Marron Fernandez, J. O.

2011-01-01

CalME procedure represents one of the most advanced tools for the design, of flexible pavements world-wide. IT is an incremental-recursive method, which means that pavements service life must be divided into many time intervals where both structural integrity and environmental conditions can be regarded as constants. It also means that the damage calculated at the end of each interval must be considered as initial condition for the next one. The goal of this type of models is the prediction of the evolution of the different distress mechanisms. The advantages of incremental-recursive procedures versus classical analytical design are shown in this paper. Advantages are shown not only in terms of design, but also as a tool in order to support structural evaluation. In particular, the potential of asphalt fatigue model incorporated in CalME is presented. this model is initially calibrated in the laboratory, and it is then re-calibrated based on the actual performance observed from field deflection testing. The model provides a reliable prediction of the future evolution of the damage of the asphalt mixture. Fatigue model validation has been conducted based on the performance from several flexible sections evaluated in CEDEX full-scale pavements test track. (Author) 14 refs.

Investigation and development of a non-destructive system to evaluate critical properties of asphalt pavements during the compaction process.

Science.gov (United States)

2013-10-01

The purpose of this report is to present findings from a two-stage investigation to develop a non-destructive system to : evaluate critical properties and characteristics of asphalt pavements during the compaction process. The first stage aligned : c...

Performance Evaluation of Crumb Rubber Modified Stone Mastic Asphalt Pavement in Malaysia

Directory of Open Access Journals (Sweden)

Nuha Salim Mashaan

2013-01-01

Full Text Available To prevent pavement distresses there are various solutions such as adopting new mix designs or utilisation of asphalt additives. The primary aim of this study was to investigate the effect of adding crumb tyre rubber as an additive to SMA mixture performance properties. This study investigated the essential aspects of modified asphalt mixtures in order to better understand the influence of CRM modifiers on volumetric, mechanical, and stiffness properties of SMA mixture. In this study, virgin bitumen 80/100 penetration grade was used, modified with crumb rubber (CRM at five different modification levels, namely, 6%, 12%, 16%, and 20%, respectively, by weight of the bitumen. The appropriate amount of the added CRM was found to be 12% by weight of bitumen. This percentage results in the maximum level of stability. The resilient modulus (Mr of modified SMA samples including different percentages of CRM was obviously higher in comparison with that of unmodified samples.

Pavement noise measurements in Poland

Science.gov (United States)

Zofka, Ewa; Zofka, Adam; Mechowski, Tomasz

2017-09-01

The objective of this study is to investigate the feasibility of the On-Board Sound Intensity (OBSI) system to measure tire-pavement noise in Poland. In general, sources of noise emitted by the modern vehicles are the propulsion noise, aerodynamic resistance and noise generated at the tire-pavement interface. In order to capture tire-pavement noise, the OBSI system uses a noise intensity probe installed in the close proximity of that interface. In this study, OBSI measurements were performed at different types of pavement surfaces such as stone mastic asphalt (SMA), regular asphalt concrete (HMA) as well as Portland cement concrete (PCC). The influence of several necessary OBSI measurement conditions were recognized as: testing speed, air temperature, tire pressure and tire type. The results of this study demonstrate that the OBSI system is a viable and robust tool that can be used for the quality evaluation of newly built asphalt pavements in Poland. It can be also applied to generate reliable input parameters for the noise propagation models that are used to assess the environmental impact of new and existing highway corridors.

Concentrations of polycyclic aromatic hydrocarbons (PAHs) and azaarenes in runoff from coal-tar- and asphalt-sealcoated pavement.

Science.gov (United States)

Mahler, Barbara J; Van Metre, Peter C; Foreman, William T

2014-05-01

Coal-tar-based sealcoat, used extensively on parking lots and driveways in North America, is a potent source of PAHs. We investigated how concentrations and assemblages of PAHs and azaarenes in runoff from pavement newly sealed with coal-tar-based (CT) or asphalt-based (AS) sealcoat changed over time. Samples of simulated runoff were collected from pavement 5 h to 111 d following application of AS or CT sealcoat. Concentrations of the sum of 16 PAHs (median concentrations of 328 and 35 μg/L for CT and AS runoff, respectively) in runoff varied relatively little, but rapid decreases in concentrations of azaarenes and low molecular weight PAHs were offset by increases in high molecular weight PAHs. The results demonstrate that runoff from CT-sealcoated pavement, in particular, continues to contain elevated concentrations of PAHs long after a 24-h curing time, with implications for the fate, transport, and ecotoxicological effects of contaminants in runoff from CT-sealcoated pavement. Published by Elsevier Ltd.

Concentrations of polycyclic aromatic hydrocarbons (PAHs) and azaarenes in runoff from coal-tar- and asphalt-sealcoated pavement

Science.gov (United States)

Mahler, Barbara J.; Van Metre, Peter C.; Foreman, William T.

2014-01-01

Coal-tar-based sealcoat, used extensively on parking lots and driveways in North America, is a potent source of PAHs. We investigated how concentrations and assemblages of PAHs and azaarenes in runoff from pavement newly sealed with coal-tar-based (CT) or asphalt-based (AS) sealcoat changed over time. Samples of simulated runoff were collected from pavement 5 h to 111 d following application of AS or CT sealcoat. Concentrations of the sum of 16 PAHs (median concentrations of 328 and 35 μg/L for CT and AS runoff, respectively) in runoff varied relatively little, but rapid decreases in concentrations of azaarenes and low molecular weight PAHs were offset by increases in high molecular weight PAHs. The results demonstrate that runoff from CT-sealcoated pavement, in particular, continues to contain elevated concentrations of PAHs long after a 24-h curing time, with implications for the fate, transport, and ecotoxicological effects of contaminants in runoff from CT-sealcoated pavement.

Characteristics Buton Natural Asphalt-Rubber (BNA-R) on the Performance Improvement of Warm Mix Asphalt Using Natural Zeolite

Science.gov (United States)

Wahjuningsih, Nurul; Pranowo Hadiwardoyo, Sigit; Jachrizal Sumabrata, R.

2018-03-01

The decrease in the ability of service of pavement can be caused by the durability factor in the pavement layer in receiving heavy traffic load and the temperature of the pavement. Permanent deformation is one of the criteria of failure of asphalt mixture. Performance assessment of the asphalt mixture can be observed from the rheological properties of asphalt binder. The use of BNA-R in this study is intended to modify the characteristics of bitumen penetration grade 60 / 70 used in warm mix asphalt. Warm mix asphalt with lower temperatures of mixing and compaction than conventional asphalt mixtures was chosen because it is more environmentally friendly. To reduce the temperature in this warm asphalt technology is achieved by using natural zeolite. Both of these materials are local materials that are widely available in Indonesia. The rheology of asphalt 60/70 modified with BNA-R indicates that the addition of BNA-R in the base asphalt increase the complex modulus value and decrease the phase angle value. These values were related to the performance of mixture in the permanent deformation criteria. Reducing the temperature of mixing and compaction should be balanced with modifying the asphalt binder used. Rutting due to permanent deformation can resulted in inconvenience to the passengers and can lead to high costs of road maintenance. To determine the permanent deformation of asphalt mix with material combinations was performed through the wheel tracking test machine with 3,780 cycles for 3 hours. The results shows that after test track over 7 thousand passes have seen permanent deformation characteristics of asphalt concrete mixture with a variation of the characteristics of bitumen.

Characteristics Buton Natural Asphalt-Rubber (BNA-R on the Performance Improvement of Warm Mix Asphalt Using Natural Zeolite

Directory of Open Access Journals (Sweden)

Wahjuningsih Nurul

2018-01-01

Full Text Available The decrease in the ability of service of pavement can be caused by the durability factor in the pavement layer in receiving heavy traffic load and the temperature of the pavement. Permanent deformation is one of the criteria of failure of asphalt mixture. Performance assessment of the asphalt mixture can be observed from the rheological properties of asphalt binder. The use of BNA-R in this study is intended to modify the characteristics of bitumen penetration grade 60 / 70 used in warm mix asphalt. Warm mix asphalt with lower temperatures of mixing and compaction than conventional asphalt mixtures was chosen because it is more environmentally friendly. To reduce the temperature in this warm asphalt technology is achieved by using natural zeolite. Both of these materials are local materials that are widely available in Indonesia. The rheology of asphalt 60/70 modified with BNA-R indicates that the addition of BNA-R in the base asphalt increase the complex modulus value and decrease the phase angle value. These values were related to the performance of mixture in the permanent deformation criteria. Reducing the temperature of mixing and compaction should be balanced with modifying the asphalt binder used. Rutting due to permanent deformation can resulted in inconvenience to the passengers and can lead to high costs of road maintenance. To determine the permanent deformation of asphalt mix with material combinations was performed through the wheel tracking test machine with 3,780 cycles for 3 hours. The results shows that after test track over 7 thousand passes have seen permanent deformation characteristics of asphalt concrete mixture with a variation of the characteristics of bitumen.

Prediction of Asphalt Creep Compliance Using Artificial Neural Networks

Directory of Open Access Journals (Sweden)

Zofka A.

2012-06-01

Full Text Available Creep compliance of the hot-mix asphalt (HMA is a primary input of the pavement thermal cracking prediction model in the recently developed Mechanistic-Empirical Pavement Design Guide (M-EPDG in the US. The HMA creep compliance is typically determined from the Indirect Tension (IDT tests and requires complex experimental setup. On the other hand, creep compliance of asphalt binders is determined from a relatively simple three- point bending test performed in the Bending Beam Rheometer (BBR device. This paper discusses a process of training an Artificial Neural Network (ANN to correlate the creep compliance values obtained from the IDT with those from an innovative approach of testing HMA beams in the BBR. In addition, ANNs are also trained to predict HMA creep compliance from the creep compliance of asphalt binder and vice versa using the BBR setup. All trained ANNs exhibited a very high correlation of 97 to 99 percent between predicted and measured values. The binder creep compliance curves built on the ANN-predicted values also exhibited good correlation with those obtained from laboratory experiments. However, the simulation of trained ANNs on the independent dataset produced a significant deviation from the expected values which was most likely caused by the differences in material composition, such as aggregate type and gradation, presence of recycled additives, and binder type.

Determination of the heating temperature of potholes surface on road pavement in the process of repairs using hot asphalt concrete mixes

Directory of Open Access Journals (Sweden)

Giyasov Botir Iminzhonovich

2014-12-01

Full Text Available In the process of roads construction the necessary transport and operational characteristics should be achieved, which depend on the quality of the applied, material and technologies. Under the loads of transport means and the influence of weather conditions on the road pavement deformations and destructions occur, which lead to worsening of transport and operational characteristics, decrease of operational life of the road and they are often the reason of road accidents. According to the data of the Strategic Research Center of "Rosgosstrah" more than 20 % of road accidents in Russia occur due to bad quality of road pavement. One of the main directions in traffic security control and prolongation of operational life for road pavement of non-rigid type is road works, as a result of which defects of pavement are eliminated and in case of timely repairs of high quality the operational life of the road increases for several years. The most widely used material for non-rigid pavement repairs is hot road concrete mixes and in case of adherence to specifications they provide high quality of works. The authors investigate the problems of hot asphalt concrete mixes for repairs of road surfaces of non-rigid type. The results of the study hot asphalt concrete mix’s temperature regimes are offered in case of repair works considering the temperature delivered to the work site and the ambient temperature depending on the type of mix and class of bitumen.

Analysis of Possibilities for Using Recycled Concrete Aggregate in Concrete Pavement

OpenAIRE

R. Pernicova; D. Dobias

2016-01-01

The present article describes the limits of using recycled concrete aggregate (denoted as RCA) in the top layer of concrete roads. The main aim of this work is to investigate the possibility of reuse of recycled aggregates obtained by crushing the old concrete roads as a building material in the new top layers of concrete pavements. The paper is based on gathering the current knowledge about how to use recycled concrete aggregate, suitability, and modification of the properties and its standa...

Contributory Factors Related to Permanent Deformation of Hot Asphalt Mixtures

Directory of Open Access Journals (Sweden)

Alaa Husein Abd

2017-03-01

Full Text Available Permanent deformation (Rutting of asphalt pavements which appears in many roads in Iraq, have caused a major impact on pavement performance by reducing the useful service life of pavement and creating services hazards for highway users. The main objective of this research is investigating the effect of some contributory factors related to permanent deformation of asphalt concrete mixture. To meet the objectives of this research, available local materials are used including asphalt binder, aggregates, mineral filler and modified asphalt binder. The Superpave mix design system was adopted with varying volumetric compositions. The Superpave Gyratory Compactor was used to compact 24 asphalt concrete cylindrical specimens. To collect the required data and investigate the development of permanent deformation in asphalt concrete under repeated loadings, Wheel-Tracking apparatus has been used in a factorial testing program during which 44 slab samples; with dimensions of 400×300×50 mm; were tested to simulate . actual pavement. Based on wheel-tracking test results, it has been concluded that increasing the compaction temperature from 110 to 150ºC caused a decreasing in permanent deformation by 20.5 and 15.6 percent for coarse and fine gradation control asphalt mixtures respectively. While the permanent deformation decreased about 21.3 percent when the compaction temperature is increased from 110 to 150ºC for coarse gradation asphalt mixtures modified with styrene butadiene styrene SBS with 3 percent by asphalt binder weight.

Asphalt emulsion; Asphalt nyuzai ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Suzuki, T. [Toa Doro Kogyo Co. Ltd., Tokyo (Japan)

1994-12-28

The emulsification, manufacture, type, applications, etc. of asphalt emulsion were introduced. The emulsification of asphalt is obtained by mixing heated asphalt into an emulsification liquid where emulsifier is added to water and then agitating it. The emulsifier has both hydrophilic and lipophilic parts in the same molecule, prevents collision between asphalt particles after being arranged properly on the surface of asphalt particles, and prevent separation into water and asphalt. The emulsion is available for penetration and for mixing depending on applications and can be classified into cation emulsion, anion emulsion, and nonionic emulsion according to the property. The emulsion is mainly applied to road pavement, reaching approximately 90 % of the total manufactured emulsion. It is also used for other areas such as the filler of a slab race of each bullet train of Sanyo, Tohoku, and Jyoetsu and is also applied to the formation of a water-proof layer by spraying a high-concentration emulsion with rubber, agricultural water channels using asphalt emulsion and nonwoven cloth, etc. in civil engineering and agricultural fields. 2 refs., 13 figs., 8 tabs.

Characterization of asphalt treated base course material

Science.gov (United States)

2010-06-01

Asphalt-treated bases are often used in new pavements; the materials are available and low-cost, but there is little data on how these materials perform in cold regions. : This study investigated four ATB types (hot asphalt, emulsion, foamed asphalt,...

Artificial intelligence modeling to evaluate field performance of photocatalytic asphalt pavement for ambient air purification.

Science.gov (United States)

Asadi, Somayeh; Hassan, Marwa; Nadiri, Ataallah; Dylla, Heather

2014-01-01

In recent years, the application of titanium dioxide (TiO₂) as a photocatalyst in asphalt pavement has received considerable attention for purifying ambient air from traffic-emitted pollutants via photocatalytic processes. In order to control the increasing deterioration of ambient air quality, urgent and proper risk assessment tools are deemed necessary. However, in practice, monitoring all process parameters for various operating conditions is difficult due to the complex and non-linear nature of air pollution-based problems. Therefore, the development of models to predict air pollutant concentrations is very useful because it can provide early warnings to the population and also reduce the number of measuring sites. This study used artificial neural network (ANN) and neuro-fuzzy (NF) models to predict NOx concentration in the air as a function of traffic count (Tr) and climatic conditions including humidity (H), temperature (T), solar radiation (S), and wind speed (W) before and after the application of TiO₂ on the pavement surface. These models are useful for modeling because of their ability to be trained using historical data and because of their capability for modeling highly non-linear relationships. To build these models, data were collected from a field study where an aqueous nano TiO₂ solution was sprayed on a 0.2-mile of asphalt pavement in Baton Rouge, LA. Results of this study showed that the NF model provided a better fitting to NOx measurements than the ANN model in the training, validation, and test steps. Results of a parametric study indicated that traffic level, relative humidity, and solar radiation had the most influence on photocatalytic efficiency.

Study on Flexible Pavement Failures in Soft Soil Tropical Regions

Science.gov (United States)

Jayakumar, M.; Chee Soon, Lee

2015-04-01

Road network system experienced rapid upgrowth since ages ago and it started developing in Malaysia during the colonization of British due to its significant impacts in transportation field. Flexible pavement, the major road network in Malaysia, has been deteriorating by various types of distresses which cause descending serviceability of the pavement structure. This paper discusses the pavement condition assessment carried out in Sarawak and Sabah, Malaysia to have design solutions for flexible pavement failures. Field tests were conducted to examine the subgrade strength of existing roads in Sarawak at various failure locations, to assess the impact of subgrade strength on pavement failures. Research outcomes from field condition assessment and subgrade testing showed that the critical causes of pavement failures are inadequate design and maintenance of drainage system and shoulder cross fall, along with inadequate pavement thickness provided by may be assuming the conservative value of soil strength at optimum moisture content, whereas the exiting and expected subgrade strengths at equilibrium moisture content are far below. Our further research shows that stabilized existing recycled asphalt and base materials to use as a sub-base along with bitumen stabilized open graded base in the pavement composition may be a viable solution for pavement failures.

Effect of the weather in the aging of asphalts by XRD

International Nuclear Information System (INIS)

Cardoso, Edson da R.; Braz, Delson; Lopes, Ricardo T.; Motta, Laura M.G. da; Barroso, Regina C.

2009-01-01

Asphalt is a sticky, black and highly viscous liquid or semi-solid that is presented in most crude petroleum and in some natural deposits. As is well known, asphalt has been the preferential choice in pavement construction since excellent utility of pavement, however, as other organic substances, it is also subjected to aging phenomena evolving with time. Asphalt aging is one of the principal factors causing deterioration of asphalt pavements. The photodegradation of asphalts must be considered in the study of the performance of asphalt pavement, especially in geographical regions where high solar radiation intensity occurs. It has an important influence in asphalt aging in tropical places as Brazil. Many methods have been applied to simulate aging of bitumen. It was just a simulation but not real aging asphalt. In this study we submitted the asphalt to the weather as sun and rain. Periodically, during 430 days, the XRD profiles were done and the results analyzed. The scattering measurements were carried out in 0-20 reflection geometry using a powder diffractometer Shimadzu XRD-6000. Scans were typically done from 8 deg to 28 deg every 0.05 deg. The parameters FWHM and peak centroid were analyzed. From 0 until 180 days the aging was faster. The peaks were marked and analyzed with the pass of time. The crystallinity of asphalt increase with weather exposition. Some angles of profiles changed the position indicating change of atomics plans. (author)

Effect of the weather in the aging of asphalts by XRD

Energy Technology Data Exchange (ETDEWEB)

Cardoso, Edson da R.; Braz, Delson; Lopes, Ricardo T., E-mail: ecardoso@lin.ufrj.b [Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Nuclear; Motta, Laura M.G. da, E-mail: Laura@coc.ufrj.b [Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Construcao Civil/Geotecnia; Barroso, Regina C., E-mail: cely@uerj.b [Universidade do Estado do Rio de Janeiro (UERJ), RJ (Brazil). Inst. de Fisica

2009-07-01

Asphalt is a sticky, black and highly viscous liquid or semi-solid that is presented in most crude petroleum and in some natural deposits. As is well known, asphalt has been the preferential choice in pavement construction since excellent utility of pavement, however, as other organic substances, it is also subjected to aging phenomena evolving with time. Asphalt aging is one of the principal factors causing deterioration of asphalt pavements. The photodegradation of asphalts must be considered in the study of the performance of asphalt pavement, especially in geographical regions where high solar radiation intensity occurs. It has an important influence in asphalt aging in tropical places as Brazil. Many methods have been applied to simulate aging of bitumen. It was just a simulation but not real aging asphalt. In this study we submitted the asphalt to the weather as sun and rain. Periodically, during 430 days, the XRD profiles were done and the results analyzed. The scattering measurements were carried out in 0-20 reflection geometry using a powder diffractometer Shimadzu XRD-6000. Scans were typically done from 8 deg to 28 deg every 0.05 deg. The parameters FWHM and peak centroid were analyzed. From 0 until 180 days the aging was faster. The peaks were marked and analyzed with the pass of time. The crystallinity of asphalt increase with weather exposition. Some angles of profiles changed the position indicating change of atomics plans. (author)

Investigation of Properties of Asphalt Concrete Containing Boron Waste as Mineral Filler

Directory of Open Access Journals (Sweden)

Cahit GÜRER

2016-05-01

Full Text Available During the manufacture of compounds in the boron mining industry a large quantity of waste boron is produced which has detrimental effects on the environment. Large areas have to be allocated for the disposal of this waste. Today with an increase in infrastructure construction, more efficient use of the existing sources of raw materials has become an obligation and this involves the recycling of various waste materials. Road construction requires a significant amount of raw materials and it is possible that substantial amounts of boron-containing waste materials can be recycled in these applications. This study investigates the usability of boron wastes as filler in asphalt concrete. For this purpose, asphalt concrete samples were produced using mineral fillers containing 4%, 5%, 6%, 7% and 8% boron waste as well as a 6% limestone filler (6%L as the control sample. The Marshall Design, mechanical immersion and Marshall Stability test after a freeze-thaw cycle and indirect tensile stiffness modulus (ITSM test were performed for each of the series. The results of this experimental study showed that boron waste can be used in medium and low trafficked asphalt concrete pavements wearing courses as filler.

Evaluation of factors that affect rutting resistance of asphalt mixes by orthogonal experiment design

Directory of Open Access Journals (Sweden)

Guilian Zou

2017-05-01

Full Text Available Rutting has been one of the major distresses observed on asphalt pavement in China, due to increasing traffic volume, heavy axle load, continuous hot weather, etc., especially in long-steep-slope section, bus stops, etc. Many factors would affect rutting resistance of asphalt pavement, including material properties, climatic condition, traffic volumes, speed, and axle types, and construction quality.The orthogonal experimental design method was used in this study to reduce the number of tests required, without comprising the validity of the test results. The testing variables and their levels were selected according to investigations and field test results. Effects of various factors on asphalt pavement rutting performance were evaluated, including the asphalt binders, mixture type (aggregate gradation, axle load, vehicle speed and temperature.In this study, the wheel tracking test was used to evaluate rutting performance, as represented by the parameter Dynamic Stability (DS, of the various asphalt mixes. Test results were analyzed using range analysis and analysis of variance (ANOVA. All four factors evaluated in this study had significant effects on pavement rutting performance. The ranking of the significance was asphalt mixture type, temperature, loading frequency, and tire-pavement contact pressure. Asphalt mixture type was the most important factor that affects rutting resistance. Within the asphalt mixtures, asphalt binder had significant effects on rutting performance of mixes more than aggregate gradation. Rutting resistance of SBS modified asphalt mixes was significantly better than neat asphalt mixes, and skeleton dense structure mixes were better than suspended dense structure mixes. Keywords: Asphalt mixes, Rutting resistance, Effect factor, Orthogonal experiment design

A review of asphalt and asphalt mixture aging

Directory of Open Access Journals (Sweden)

Wilmar Darío Fernández-Gómez

2013-01-01

Full Text Available This paper presents an extensive review of the pertinent literature regarding asphalt and asphalt mixture Aging. Aging affects flexible pavement performance and is produced by intrinsic and extrinsic variables as well as exposure time. Intrinsic variables include asphalt and aggregate properties, a mixture’s asphalt content, binder film thickness and air void content; extrinsic variables are associated with production (short-term aging and exposure to environmental field conditions (long-term aging. Taken together, both variables demonstrate that aging results from three distinct mechanisms: volatilisation, oxidation and steric hardening. Temperature, pressure and photo degradation treatments are used to simulate aging in the laboratory and empirical and semi-empirical models are created to represent and study aging. Aging increases asphalt complex modulus and decreases the phase angle. Mixtures become stiffer while fatigue life becomes reduced. Carbonyl and sulfoxide group formation in asphalt are often studied as such chemical changes show oxidation in aged asphalts. The prevailing models used to predict asphalt aging are discussed, though more comprehensive research into asphalt aging is still needed.

Self-healing properties of recycled asphalt mixtures containing metal waste: An approach through microwave radiation heating.

Science.gov (United States)

González, A; Norambuena-Contreras, J; Storey, L; Schlangen, E

2018-05-15

The concept of self-healing asphalt mixtures by bitumen temperature increase has been used by researchers to create an asphalt mixture with crack-healing properties by microwave or induction heating. Metals, normally steel wool fibers (SWF), are added to asphalt mixtures prepared with virgin materials to absorb and conduct thermal energy. Metal shavings, a waste material from the metal industry, could be used to replace SWF. In addition, reclaimed asphalt pavement (RAP) could be added to these mixtures to make a more sustainable road material. This research aimed to evaluate the effect of adding metal shavings and RAP on the properties of asphalt mixtures with crack-healing capabilities by microwave heating. The research indicates that metal shavings have an irregular shape with widths larger than typical SWF used with asphalt self-healing purposes. The general effect of adding metal shavings was an improvement in the crack-healing of asphalt mixtures, while adding RAP to mixtures with metal shavings reduced the healing. The average surface temperature of the asphalt samples after microwave heating was higher than temperatures obtained by induction heating, indicating that shavings are more efficient when mixtures are heated by microwave radiation. CT scan analysis showed that shavings uniformly distribute in the mixture, and the addition of metal shavings increases the air voids. Overall, it is concluded that asphalt mixtures with RAP and waste metal shavings have the potential of being crack-healed by microwave heating. Copyright © 2018 Elsevier Ltd. All rights reserved.

Analysis of asphalt mix surface-tread rubber interaction by using finite element method

Directory of Open Access Journals (Sweden)

Santosh Kumar Srirangam

2017-08-01

Full Text Available The surface texture of the pavement plays a very important role in driving the frictional properties at the tire rubber-pavement interface. Particularly, the hysteretic friction due to viscoelastic deformations of rubber depends mainly on the pavement surface texture. In the present paper, the effect of micromechanical pavement surface morphology on rubber block friction was brought in by comparing the friction results for three different asphalt mix morphological surfaces, named stone mastic asphalt (SMA, ultra-thin surfacing (UTS and porous asphalt (PA. The asphalt surface morphologies of these mixes were captured by using an X-ray tomographer, from which the resulting images micromechanical finite element (FE meshes for SMA, UTS and PA pavements were developed by means of the SimpleWare software. In the FE model, the rubber and asphalt binder were modeled as viscoelastic (VE materials and the formulation was given in the large deformation framework. FE simulations were then carried out by using contact algorithm between rubber and the road surface. It was observed that the rubber friction inversely varies with the sliding speed and positively varies with the pressure for all the pavement morphological and stiffness conditions. Furthermore, it was observed that the highly porous pavement surface results in large dissipation of energy, hence, large rubber friction which shows that the mix characteristics of pavements have a significant effect on rubber friction.

Laboratory evaluation of recycled concrete as aggregate in new concrete pavements.

Science.gov (United States)

2014-09-01

The Washington State Department of Transportation (WSDOT) has initiated a research project to investigate the use of recycled concrete as : aggregates (RCA) in Portland (hydraulic) cement concrete pavements (PCCP). The planned source for the RCA in t...

Impact of the Superpave hot mix asphalt properties on its permanent deformation behavior

Directory of Open Access Journals (Sweden)

Qasim Zahra

2018-01-01

Full Text Available In Iraq, the severity of rutting has increased in asphalt pavements possibly due to the increase in truck axle loads, tyre pressure, and high pavement temperature in summer. As of late, Superpave has been accounted as an enhanced system for performance based design, analysis of asphalt pavement performance prediction for asphalt concrete mixes. In this research the development of permanent deformation in asphalt concrete under repeated loadings was investigated, Wheel-Tracking apparatus has been used in a factorial testing program during which 44 slab samples were tested to simulate actual pavement. The objectives of the present research include; investigating the main factors affecting rutting in asphalt concrete mixture, quantifying the effect of SBS polymer and steel reinforcement on asphalt concrete mixtures in addition to studying the effect of variables on the asphalt concrete mixes against moisture sensitivity. It has been determined that that increasing of compaction temperature from 110 to 150°C will decrease the permanent deformation by 20.5 and 15.6 percent for coarse and fine gradation control asphalt mixtures, respectively. While the permanent deformation decreases by 21.3 percent when the compaction temperature is increased from 110 to 150°C for coarse gradation SBS modified asphalt mixtures.

Quantifying Asphalt Emulsion-Based Chip Seal Curing Times Using Electrical Resistance Measurements.

Science.gov (United States)

2017-04-15

Chip sealing typically consists of covering a pavement surface with asphalt emulsion into which aggregate chips are embedded. The asphalt emulsion cures through the evaporation of water, thus providing mechanical strength to adhere to the pavement wh...

Present status and future of various rubber materials. ; Asphalt. Kakushu gomu zairyo no genjo to kongo. ; Asphalt

Energy Technology Data Exchange (ETDEWEB)

Wakisaka, S. (Toa Doro Kogyo Co. Ltd., Tokyo (Japan))

1991-12-15

Asphalt is obtained at a rate of about 25 Kg per 1 Kl of oil and is produced at about 5 million tons per annum in Japan, 80 % of which is now used for the pavement of road. The purpose of this study is to examine the possibilities of developing new applications of asphalt to the anti-vibration, vibration-control and anti-noise materials, though its uses have already been diversified in fields other than for road paving, due to excellent performance regardless of cheap cost. In the paper, firstly, under a title of what is asphalt, the history, the composition and internal structure of asphalt were considered. Secondly, the dynamic characteristics of asphalt were considered. And lastly, under a title of the application of asphalt, examples of the application of asphalt to anti-noise materials were examined in the field of architecture, automobile and civil engineering respectively. Especially, in the field of civil engineering, improvements of flexibility and vibration-control by using the cement asphalt mortar (CAM) in the anti-vibration A-type slab track for railway, and also anti-noise and anti-vibration technologies applied to the road pavement body by using the ferrite asphalt were reviewed. 11 refs., 10 figs., 8 tabs.

Advanced evaluation of asphalt mortar for induction healing purposes

NARCIS (Netherlands)

Apostolidis, P.; Liu, X.; Scarpas, Athanasios; Kasbergen, C.; van de Ven, M.F.C.

2016-01-01

Induction heating technique is an innovative asphalt pavement maintenance method that is applied to inductive asphalt concrete mixes in order to prevent the formation of macro-cracks by increasing locally the temperature of asphalt. The development of asphalt mixes with improved electrical and

Influence of Pavement on Fatigue Performance of Urban Steel Box Girder Deck

Directory of Open Access Journals (Sweden)

Zheng Zhongyue

2016-01-01

Full Text Available Based on spatial finite element analysis method, the Influence of pavement on fatigue performance of orthotropic steel deck was analyzed in terms of pavement system, asphalt pavement stiffness. The result shows that compared with asphalt pavement system, RPC pavement system can not only obviously improve the stress condition of steel bridge deck, but also significantly extend the fatigue life of steel bridge panel; Increasing the stiffness of pavement layer can obviously reduce the stress amplitude of fatigue details, especially for direct contact with the pavement.

Modified asphalt; Kairyo asphalt ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Takarabe, A. [Mitsubishi Oil Co. Ltd., Tokyo (Japan)

1994-12-28

Modified asphalt in the area of road pavement in the relation of measures against flow on a road surface was introduced. The condition of road damage includes the print of a wheel, crack, and wear and semi-blown asphalt whose deformation is difficult even if temperature is increased to approximately 60 {degree}C and asphalt with rubber and resin are used to prevent these. The semi-blown asphalt is obtained by adding cut-back material to the normal asphalt, heating it, blowing air into it, and then oxidizing and polymerizing it, is harder and is more elastic than the normal asphalt, and has smaller viscosity change due to temperature change. The viscosity at 60 {degree}C was determined to be 10000{plus_minus}2000 poise according to the relationship between viscosity and crack using a large-scale execution experiment. The asphalt with rubber and resin is formed by adding modified material of styrene - butadiene copolymer and by adding thermoplastic elastomer and the former is used for preventing slide and the latter is used for preventing flow and wear. 10 refs., 6 figs., 2 tabs.

Inverted base pavements: construction and performance

KAUST Repository

Papadopoulos, Efthymios

2017-05-11

Inverted base pavements involve a well-compacted granular aggregate base built between a thin asphalt concrete layer and a cement-treated base. Inverted base pavements can be constructed using conventional equipment and procedures but require proper quality control. This study reviews the extensive South African experience and case histories in the USA. Accumulating evidence suggests that inverted base pavements are a viable alternative and can outperform conventional pavements at a lower cost. Inverted base pavements rely on the complementary interaction between layers. The cement-treated base provides a stiff foundation for efficient compaction and constrains the deformation of the stress-sensitive granular aggregate base. The thin asphalt surface layer deforms as a membrane and develops low tensile stress. Additional large-scale field tests should be conducted to assess the performance of inverted base pavement designs in a wide range of conditions relevant to the USA.

VISCOELASTIC STRUCTURAL MODEL OF ASPHALT CONCRETE

Directory of Open Access Journals (Sweden)

V. Bogomolov

2016-06-01

Full Text Available The viscoelastic rheological model of asphalt concrete based on the generalized Kelvin model is offered. The mathematical model of asphalt concrete viscoelastic behavior that can be used for calculation of asphalt concrete upper layers of non-rigid pavements for strength and rutting has been developed. It has been proved that the structural model of Burgers does not fully meet all the requirements of the asphalt-concrete.

Qualitative criteria and thresholds for low noise asphalt mixture design

Science.gov (United States)

Vaitkus, A.; Andriejauskas, T.; Gražulytė, J.; Šernas, O.; Vorobjovas, V.; Kleizienė, R.

2018-05-01

Low noise asphalt pavements are cost efficient and cost effective alternative for road traffic noise mitigation comparing with noise barriers, façade insulation and other known noise mitigation measures. However, design of low noise asphalt mixtures strongly depends on climate and traffic peculiarities of different regions. Severe climate regions face problems related with short durability of low noise asphalt mixtures in terms of considerable negative impact of harsh climate conditions (frost-thaw, large temperature fluctuations, hydrological behaviour, etc.) and traffic (traffic loads, traffic volumes, studded tyres, etc.). Thus there is a need to find balance between mechanical and acoustical durability as well as to ensure adequate pavement skid resistance for road safety purposes. Paper presents analysis of the qualitative criteria and design parameters thresholds of low noise asphalt mixtures. Different asphalt mixture composition materials (grading, aggregate, binder, additives, etc.) and relevant asphalt layer properties (air void content, texture, evenness, degree of compaction, etc.) were investigated and assessed according their suitability for durable and effective low noise pavements. Paper concluded with the overview of requirements, qualitative criteria and thresholds for low noise asphalt mixture design for severe climate regions.

Volumetric Analysis and Performance of Hot Mix Asphalt with Variable Rap Content

Directory of Open Access Journals (Sweden)

Arshad Ahmad Kamil

2017-01-01

Full Text Available Incorporating Reclaimed Asphalt Pavement (RAP to the asphalt concrete mixture for highway construction offer many benefits including energy consumption, conservation of natural resources and preservation of the environment to associated emissions. This paper presents a study on performance of Hot Mix Asphalt with variable RAP content. The study is carried out to evaluate the Marshall Properties and Performance of RAP-Asphalt mixes using conventional asphaltic concrete mix AC14. Marshall Mix Design Method was used to produce control mix (0% RAP and RAP-Asphalt mixes samples which consist of 15% RAP, 25% RAP and 35% RAP in accordance with Specifications for Road Works of Public Works Department, Malaysia. The Marshall Properties analysis was performed to ensure compliance with Marshall Requirements, The resilient modulus test was performed to measure the stiffness of the mixes while Modified Lottman test was conducted to evaluate the moisture susceptibility of these mixes. The results obtained showed that there were no substantial difference in Marshall Properties, moisture susceptibility and indirect tensile strength between RAP-Asphalt mixes with the control mix. The test results indicated that recycled mixes performed as good as the performance of conventional HMA in terms of moisture susceptibility and resilient modulus. It is recommended that further research be carried out for asphalt mixes containing more than 35% of RAP material.

Performance prediction of hot mix asphalt from asphalt binders

International Nuclear Information System (INIS)

Hafeez, I.; Kamal, M.A.; Shahzad, Q.; Bashir, N.; Ahadi, M.R.

2012-01-01

Asphalt binder being a high weight hydrocarbon contains asphaltene and maltene and is widely used as cementing materials in the construction of flexible pavements. Its performance in hot mix asphalt also depends on combining with different proportions of aggregates. The main objective of this study was to characterize asphalt cement rheological behavior and to investigate the influence of asphalt on asphalt-aggregate mixtures prepared with virgin binders and using polymers. Binder rheology and mixtures stiffness were determined under a range of cyclic loadings and temperature conditions. Master curves were developed for the evaluation of relationship between parameters like complex modulus and phase angle at different frequencies. Horizontal shift factors were also computed to determine time and temperature response of binders and mixes. The results showed that the stiffness of both the binder and the mixes depends on temperature and frequency of load. Polymer modified binder is least susceptible to temperature variations as compared to other virgin asphalt cement. Performance of asphalt mixtures can be predicted from those of asphalt binders using the master curve technique. (author)

Synthesis of the european national requirements and practices for recycling in HMA and WMA (DIRECT_MAT PROJECT)

OpenAIRE

IPAVEC , Aleksander; Marsac , Paul; Mollenhauer , Konrad

2012-01-01

The purpose of the 2009-2011 European project DIsmantling and RECycling Techniques for road MATerials is to contribute to the waste minimization in road maintenance and construction by sharing and disseminating, at a European level, the national know-how and sustainable practices regarding the dismantling of the pavements and the recycling of the reclaimed materials. In the framework of the DIRECT_MAT subproject Asphalt materials, the present paper gives a broad overview of the European polic...

Using Tire/Pavement Interface Noise Results to Define Statistically Similar Bituminous Pavements in Massachusetts

OpenAIRE

Hencken, John; Haas, Edwin; Bennert, Thomas

2012-01-01

In October 2010, the Center for Advanced Infrastructure and Transportation (CAIT) utilized the On-Board Sound Intensity Method in Massachusetts to evaluate seven Open-Graded Friction Courses (OGFC) and eight Asphalt Rubber Gap Graded (ARGG) pavements for MassDOT. Since major concerns regarding pavement selection in the northeast revolve around winter conditions and winter maintenance, if noise level similarities could be found between ARGG and OGFC pavements, pavement engineers would be able ...

Implementing energy efficient pavements: A socio-economic analysis of the development and implementation of energy efficient pavements with low rolling resistance

DEFF Research Database (Denmark)

Axelsen, Christian; Pettinari, Matteo; Schmidt, Bjarne

2017-01-01

for the transportation sector is to make road networks more energy efficient by implementing pavements with low rolling resistance, leading to lower fuel consumption. Through a series of projects focusing on reducing rolling resistance conducted since 2010, the Danish Road Directorate (DRD) has developed a durable......, energy-efficient asphalt pavement. Socio-economic analyses conducted to quantify the benefit to society associated with implementing these asphalt pavements have demonstrated very high benefits. The demonstrated results in terms of durability, energy efficiency and socio-economics have resulted...... in substantial government funding being provided for demonstration trials on 50 kilometers of energy-efficient pavement in 2018. The implementation of energy-efficient pavements will enable Denmark to contribute to the out-of-quota 2030-emission cuts in line with EU regulations....

Effect of crumb rubber on the mechanical properties of crushed recycled pavement materials.

Science.gov (United States)

Li, Jie; Saberian, Mohammad; Nguyen, Bao Thach

2018-07-15

The low-carbon footprint of using recycled construction and demolition (C&D) aggregates in civil engineering infrastructure applications has been considered to be a significant solution for the replacement of conventional pavement aggregates. Investigations regarding the use of crumb rubber in the base and subbase layers of pavement have been well documented. However, information on the effects of crumb rubber and its size within C&D aggregates as the base/subbase layers is still very limited. In this study, crumb rubber with particle sizes ranging from 400 to 600 μm (fine) to 10-15 mm (coarse), 20 mm recycled crushed concrete (RCC), and 20 mm crushed rock (CR) were used. The crumb rubber was added to the two groups of C&D aggregates at 0.5, 1 and 2% by weight percentages of the aggregates. The effect of crumb rubber on the mechanical properties (such as California bearing ratio, unconfined compressive strength, aggregate crushing value, dynamic lightweight cone penetrometer, Clegg impact value, Los Angeles abrasion values, and resilient modulus) of the C&D aggregates was then examined. Based on the experimental test results, it was found that crumb rubber can be recycled as a waste material for the base and subbase layers in the pavement. Copyright © 2018 Elsevier Ltd. All rights reserved.

Cooler reflective pavements give benefits beyond energy savings: durability and illumination

International Nuclear Information System (INIS)

Pomerantz, Melvin; Akbari, Hashem; Harvey, John T.

2000-01-01

City streets are usually paved with asphalt concrete because this material gives good service and is relatively inexpensive to construct and maintain. We show that making asphalt pavements cooler, by increasing their reflection of sunlight, may lead to longer lifetime of the pavement, lower initial costs of the asphalt binder, and savings on street lighting and signs. Excessive glare due to the whiter surface is not likely to be a problem

A Research on Low Modulus Distributed Fiber Optical Sensor for Pavement Material Strain Monitoring.

Science.gov (United States)

Meng, Lingjian; Wang, Linbing; Hou, Yue; Yan, Guannan

2017-10-19

The accumulated irreversible deformation in pavement under repeated vehicle loadings will cause fatigue failure of asphalt concrete. It is necessary to monitor the mechanical response of pavement under load by using sensors. Previous studies have limitations in modulus accommodation between the sensor and asphalt pavement, and it is difficult to achieve the distributed monitoring goal. To solve these problems, a new type of low modulus distributed optical fiber sensor (DOFS) for asphalt pavement strain monitoring is fabricated. Laboratory experiments have proved the applicability and accuracy of the newly-designed sensor. This paper presents the results of the development.

A comprehensive review on self-healing of asphalt materials: Mechanism, model, characterization and enhancement.

Science.gov (United States)

Sun, Daquan; Sun, Guoqiang; Zhu, Xingyi; Guarin, Alvaro; Li, Bin; Dai, Ziwei; Ling, Jianming

2018-05-09

Self-healing has great potential to extend the service life of asphalt pavement, and this capability has been regarded as an important strategy when designing a sustainable infrastructure. This review presents a comprehensive summary of the state-of-the-art investigations concerning the self-healing mechanism, model, characterization and enhancement, ranging from asphalt to asphalt pavement. Firstly, the self-healing phenomenon as a general concept in asphalt materials is analyzed including its definition and the differences among self-healing and some viscoelastic responses. Additionally, the development of self-healing in asphalt pavement design is introduced. Next, four kinds of possible self-healing mechanism and corresponding models are presented. It is pointed out that the continuum thermodynamic model, considering the whole process from damage initiation to healing recovery, can be a promising study field. Further, a set of self-healing multiscale characterization methods from microscale to macroscale as well as computational simulation scale, are summed up. Thereinto, the computational simulation shows great potential in simulating the self-healing behavior of asphalt materials from mechanical and molecular level. Moreover, the factors influencing self-healing capability are discussed, but the action mechanisms of some factors remain unclear and need to be investigated. Finally, two extrinsic self-healing technologies, induction heating and capsule healing, are recommended as preventive maintenance applications in asphalt pavement. In future, more effective energy-based healing systems or novel material-based healing systems are expected to be developed towards designing sustainable long-life asphalt pavement. Copyright © 2017 Elsevier B.V. All rights reserved.

State of the Art Study on Aging of Asphalt Mixtures and Use of Antioxidant Additives

Directory of Open Access Journals (Sweden)

Okan Sirin

2018-01-01

Full Text Available The detrimental effects of hardening in asphalt pavements were first recognized by pioneering pavement engineers in the 1900s and have been studied extensively during the last 70 years. This hardening process, referred to as asphalt aging, is generally defined as change in the rheological properties of asphalt binders/mixtures due to changes in chemical composition during construction and its service life period. Aging causes the asphalt material to stiffen and embrittle, which affects the durability and leads to a high potential for cracking. This paper presents the state of the art on asphalt and asphalt mixture aging and use of antioxidant additives to retard the aging. A picture of complex molecular structure of asphalt and its changes due to atmospheric condition and various protocols used to simulate aging in laboratory environment are also discussed. Emphasis is given on recent studies on simulation of aging of asphalt mixtures as there has been limited research on mixtures compared to the asphalt binder. Finally, this paper presents the application of antiaging techniques and its mechanism, use of various types of antioxidant additives to retard aging of asphalt and, hence, improve the performance of asphalt pavements.

Particulate matter mass concentrations produced from pavement surface abrasion

Directory of Open Access Journals (Sweden)

Fullova Dasa

2017-01-01

Full Text Available According to the latest findings particulate matter belong to the most significant pollutants in Europe together with ground-level ozone O3 and nitrogen dioxide NO2. Road traffic is one of the main sources of particulate matter. Traffic volume has unpleasant impact on longevity of the pavements and also on the environment. Vehicle motions cause mechanical wearing of the asphalt pavement surface - wearing course by vehicle tyres. The paper deals with abrasion of bituminous wearing courses of pavements. The asphalt mixtures are compared in terms of mechanically separated particulate matter. The samples of asphalt mixtures were rutted in wheel tracking machine. The particulate matter measurements were performed in laboratory conditions. The experimental laboratory measurements make it possible to sample particulates without contamination from exhaust emissions, abraded particles from vehicles, resuspension of road dust and climate affects. The paper offers partial results of measurements on six trial samples of asphalt mixtures with different composition. It presents particulate matter morphology and the comparison of rutted asphalt samples in terms of PM mass concentrations and chemical composition.

Polycyclic aromatic hydrocarbons emitted from a hot-mix drum, asphalt plant: study of the influence from use of recycled bitumen

Energy Technology Data Exchange (ETDEWEB)

Ventura, A.; Jullien, A.; Moneron, P. [Lab. Central des Ponts et Chaussees, Div. Technologie du Genie Civil et Environnement, Section Developpement Durable, Bouguenais (France)

2007-11-15

A study was conducted to determine if the use of recycled asphalt aggregate influences emissions of polycyclic aromatic hydrocarbons (PAH). Hot bitumen contains PAH compounds which have been gaining increasing attention due to their toxicity. In addition, the energy consumed during asphalt mixing can reach 60 per cent of the total energy needed for the construction and maintenance of a road over a 30-year service life. Asphalt hot mixing is one of the most common processes found in the road sector. It requires warming and drying aggregate through combustion. In order to minimize emissions, the major influential parameters must be identified. A joint research program involving several institutions has been launched to conduct an experimental campaign on the Blois Hot Mix Asphalt plant, with quantification of the 16 PAH listed by the United States Environmental Protection Agency. Variations in asphalt recycling rate favour emissions of heavy molecular weight PAH, among those analysed. It was determined that specific markers of combustion and materials may contribute to a better understanding of the entire hot asphalt mixing process. It was suggested that chemical characterization of bitumen may help in predicting PAH emissions. 24 refs., 6 tabs., 5 figs.

Fatigue and rutting lives in flexible pavement

Directory of Open Access Journals (Sweden)

Ahmed Ebrahim Abu El-Maaty Behiry

2012-12-01

Full Text Available Flexible pavement is designed based on axle load limits and climatic conditions. The Egyptian code has specified certain load limits that should not be exceeded. The overweight trucks cause severe deterioration to the pavement and thus reduce its life. The study aims at studying the effect of axle load increase, and the variation in pavement modulus, on the overall pavement life. The research uses the BISAR software and the Egyptian environmental and pavement materials conditions to estimate the tensile strains occurring under the asphalt concrete (AC layer and the compressive strains above the subgrade surface. The results revealed that tensile and compressive strain increased with increasing axle loads and decreased with increasing asphalt layer modulus thus the violating trucks should be unloaded when their weights exceed certain limits. Base thickness and subgrade resilient modulus were the key elements which control the equilibrium between fatigue and rutting lives.

Sustainable asphalt pavement: Application of slaughterhouse waste oil and fly ash in asphalt binder

Science.gov (United States)

Sanchez Ramos, Jorge Luis

Increasing energy costs, lack of sufficient natural resources and the overwhelming demand for petroleum has stimulated the development of alternative binders to modify or replace petroleum-based asphalt binders. In the United States, the petroleum-based asphalt binder is mainly used to produce the Hot Mix Asphalt (HMA). There are approximately 4000 asphalt plants that make 500 million tons of asphalt binder valued at roughly 3 billion/year. The instability of the world's oil market has pushed oil prices to more than 80 per barrel in 2012, which increased the cost of asphalt binder up to $570 per ton. Therefore, there is a timely need to find alternative sustainable resources to the asphalt binder. This paper investigates the possibility of the partial replacement of the asphalt binder with slaughterhouse waste and/or fly ash. In order to achieve this objective, the asphalt binder is mixed with different percentages of waste oil and/or fly ash. In order to investigate the effect of these additives to the performance of the asphalt binder, a complete performance grade test performed on multiple samples. The results of the performance grade tests are compared with a control sample to observe how the addition of the waste oil and/or fly ash affects the sample. Considering the increasing cost and demand of asphalt, the use of slaughterhouse waste oil and/or fly ash as a partial replacement may result in environmental and monetary improvements in the transportation sector.

Mechanical properties of hot mix asphalt made with recycled aggregates from reclaimed construction and demolition debris

Directory of Open Access Journals (Sweden)

Taibo, J.

2007-03-01

Full Text Available The mix design for asphalt mixtures containing recycled aggregates from construction and demolition debris was evaluated. The tests conducted to characterize the mechanical behaviour of these mixtures showed that the mechanical properties of mixtures with recycled and virgin aggregate are similar. The asphalt mixtures containing recycled aggregate proved to have lower resistance to water action. Nonetheless, recycled aggregate was found to be potentially usable in asphalt mixtures if higher quality materials are selected and such low resistance is corrected. This will call for expanding upon the preliminary work described in the present article.En este trabajo se dosificaron mezclas bituminosas fabricadas con áridos reciclados de residuos de construcción y demolición. Se realizaron una serie de ensayos que permitieron caracterizar el comportamiento mecánico de estas mezclas. Los parámetros mecánicos de las mezclas con áridos reciclados son similares a los de las mezclas fabricadas únicamente con áridos naturales de cantera. Sin embargo, las mezclas bituminosas con áridos reciclados tuvieron un mal comportamiento frente a la disminución de la resistencia por pérdida de cohesión por la acción del agua. No obstante, mediante la selección de materiales de mejor calidad y corrección de este mal comportamiento, existen posibilidades de utilizar áridos reciclados en mezclas bituminosas. Para ello será necesario ampliar la primera aproximación realizada en este artículo.

Knowledge Discovery and Pavement Performance : Intelligent Data Mining

NARCIS (Netherlands)

Miradi, M.

2009-01-01

The main goal of the study was to discover knowledge from data about asphalt road pavement problems to achieve a better understanding of the behavior of them and via this understanding improve pavement quality and enhance its lifespan. Four pavement problems were chosen to be investigated; raveling

Microorganism Removal in Permeable Pavement Parking Lots ...

Science.gov (United States)

Three types of permeable pavements (pervious concrete, permeable interlocking concrete pavers, and porous asphalt) were monitored at the Edison Environmental Center in Edison, New Jersey for indicator organisms such as fecal coliform, enterococci, and E. coli. Results showed that porous asphalt had much lower concentration in monitored infiltrate compared to pervious concrete and permeable interlocking concrete pavers. Concentrations of monitored organisms in infiltrate from porous asphalt were consistently below the bathing water quality standard. Fecal coliform and enterococci exceeded bathing water quality standards more than 72% and 34% of the time for permeable interlocking concrete pavers and pervious concrete, respectively. Purpose is to evaluate the performance of permeable pavement in removing indicator organisms from infiltrating stormwater runoff.

Asphalt mix characterization using dynamic modulus and APA testing.

Science.gov (United States)

2005-11-01

final report summarizes two research efforts related to asphalt mix characterization: dynamic modulus and Asphalt Pavement Analyzer testing. One phase of the research consisted of a laboratory-based evaluation of dynamic modulus of Oregon dense-grade...

Effects of laboratory heating, cyclic pore pressure, and cyclic loading on fracture properties of asphalt mixture [summary].

Science.gov (United States)

2012-04-01

Asphalt pavement ages continuously, beginning with production and construction and thoughout its service life. "Aging" refers to many changes in asphalt properties over time that generally result in increased pavement damage. Because aging is often a...

Experimental investigation of basic oxygen furnace slag used as aggregate in asphalt mixture.

Science.gov (United States)

Xue, Yongjie; Wu, Shaopeng; Hou, Haobo; Zha, Jin

2006-11-16

Chinese researchers have commenced a great deal of researches on the development of application fields of basic oxygen steel making furnace slag (BOF slag) for many years. Lots of new applications and properties have been found, but few of them in asphalt mixture of road construction engineering. This paper discussed the feasibility of BOF steel slag used as aggregate in asphalt pavement by two points of view including BOF steel slag's physical and micro-properties as well as steel slag asphalt materials and pavement performances. For the former part, this paper mainly concerned the mechanochemistry and physical changes of the steel slag and studied it by performing XRD, SEM, TG and mercury porosimeter analysis and testing method. In the second part, this paper intended to use BOF steel slag as raw material, and design steel slag SMA mixture. By using traditional rutting test, soak wheel track and modified Lottman test, the high temperature stability and water resistance ability were tested. Single axes compression test and indirect tensile test were performed to evaluate the low temperature crack resistance performance and fatigue characteristic. Simultaneously, by observing steel slag SMA pavement which was paved successfully. A follow-up study to evaluate the performance of the experimental pavement confirmed that the experimental pavement was comparable with conventional asphalt pavement, even superior to the later in some aspects. All of above test results and analysis had only one main purpose that this paper validated the opinion that using BOF slag in asphalt concrete is feasible. So this paper suggested that treated and tested steel slag should be used in a more extensive range, especially in asphalt mixture paving projects in such an abundant steel slag resource region.

Feasibility of perpetual pavement stage construction in China: A life cycle cost analysis

Directory of Open Access Journals (Sweden)

Zhongyin Guo

2016-12-01

Full Text Available The main objective of pavement design and management is to build sustainable pavement structure with minimum costs during its whole life. There are many uncertainties in the process of pavement design pertaining many of its variables, such as future traffic estimation, long time behavior of materials, future weights and types of traveling vehicles, availability of funds etc. Therefore, it is important to apply pavement stage construction technique during the process of pavement design and management to minimize the risk associated with these uncertainties. From the beginning of 2000, the research and application of perpetual asphalt pavement (PP technology has been deployed in China. The semi rigid base for asphalt pavement has been normally considered as typical component of high class highways in the design according to the Chinese experience since 1997. The research objective is to apply pavement stage construction for the evaluation of life cycle costs of Chinese perpetual and traditional semi rigid pavements using operational pavement management system in addition to examine its suitability for design and construction of more economical and durable flexible pavements. It has been found that the stage construction of asphalt layers in PP over semi rigid pavement foundation will create more sustainable and trusted pavement structures in spite of 2–5% increase in present total cost.

Interfacial debonding of ice-asphalt concrete

Energy Technology Data Exchange (ETDEWEB)

Tazawa, E.; Mizoue, Y. (Hiroshima Univ., Hiroshima (Japan)); Kojima, T. (Hitachi Chemical Co. Ltd., Tokyo (Japan))

1992-09-20

Series of experimental investigations were carried out to clarify the bonding mechanism between ice and asphalt and to develop a new technique to reduce bonding resistance. The surface bonding resistance was measured by three methods and the main variables taken into consideration have been surface energy, surface roughness and stiffness of asphalt. Surface energy was varied by using various water repellents and the stiffness of the concrete was varied by mixing rubber particles. Correlations of the three variables were studied and the following results have been obtained. Decreasing of surface energy and increasing of deformability of asphalt concrete has been the effective method to decrease the bonding between ice and asphalt. For the case of water repellent coated surface, shear debonding strength has been linearly related to the energy required for debonding by dynamic tension and the shear debonding strength has decreased with the decrease in roughness of pavement. In the case of surface without using repellent, shear debonding strength has not been influenced by surface energy and roughness of pavement. 6 refs., 16 figs., 7 tabs.

Potential to use waste tires as supplemental fuel in pulp and paper mill boilers, cement kilns and in road pavement

Energy Technology Data Exchange (ETDEWEB)

Barlaz, M.A.; Eleazer, W.E. II (North Carolina State Univ., Raleigh, NC (United States). Dept. of Civil Engineering); Whittle, D.J.

1993-12-01

The objective of this paper is to evaluate the recycling potential of waste tires as an energy source and for use in road pavement. North Carolina, U.S.A., is used as a case study. Scrap tires may be burned for supplemental fuel in pulp and paper mill boilers and cement kilns. Five pulp and paper mill boilers in North Carolina could consume over 90% of the 6 million tires generated annually in the state. Cement kilns located within 400 km of North Carolina population centers could consume about 6.6 million tires annually. Based on the quantity of pavement laid in North Carolina, non-proprietary and proprietary versions of asphalt rubber concrete have the potential to consume 1.8 and 7.2 million tires, respectively. Rubber modified asphalt concrete has the potential to consume up to 16.5 million tires. However, technological and economic limitations suggest that large scale implementation is unlikely for the short term. Environmental considerations pertaining to each alternative are discussed. (author)

Rheological characterization of asphalt binders used in strain relief asphalt mixtures (SRAM)

OpenAIRE

Vasconcelos, Kamilla L.; Bariani Bernucci, Liedi Legi; Midori Takahashi, Marcia; Castelo-Branco, Verônica T. F.

2017-01-01

Abstract The use of ´interlayers´ that tolerate high tensile and shear strain that exists above cracks in deteriorated pavements is becoming an interesting solution to prevent reflective cracking. Recent advances in polymer technology have led to binders that can be used to produce interlayer mixtures with good mechanical properties. In this study, two polymer-modified asphalt binders were evaluated, both from the production of strain relief asphalt mixtures used as interlayers in the field. ...

Summary report on the performance of open graded friction course quieter pavements : I-5 Lynnwood, SR-520 Medina, I-405 Bellevue.

Science.gov (United States)

2013-09-01

This document summarizes the acoustic properties and pavement performance of three asphalt quieter pavement projects. Each of the projects included open graded friction course pavement built with sections of crumb rubber and polymer modified asphalt ...

Pavement performance evaluation, phase II : data collection.

Science.gov (United States)

2008-12-01

Phase I and II of this study tested approximately 1500 rehabilitated pavements (asphalt and PCC) : throughout the State. These pavements ranged from 5 to 15 years old and were intended to develop a : snapshot of how various rehabilitations were perfo...

Study of Antiultraviolet Asphalt Modifiers and Their Antiageing Effects

Directory of Open Access Journals (Sweden)

Jinxuan Hu

2017-01-01

Full Text Available Ultraviolet (UV radiation causes serious ageing problems on pavement surface. In recent years, different UV blocking materials have been used as modifiers to prevent asphalt ageing during the service life of the pavement. In this study, three different materials have been used as modifiers in base asphalt to test their UV blocking effects: layered double hydroxides (LDHs, organomontmorillonite (OMMT, and carbon black (CB. UV ageing was applied to simulate the ageing process and softening point, penetration, ductility, DSR (Dynamic Shear Rheometer test, and Fourier Transform Infrared Spectroscopy (FTIR test were conducted to evaluate the anti-UV ageing effects of the three UV blocking modifiers. Physical property tests show that base asphalt was influenced more seriously by UV radiation compared to the modified asphalt. DSR test results indicate that the complex modulus of asphalt before UV ageing is increased because of modifiers, while the complex modulus of base asphalt after UV ageing is higher than that of the modified asphalt, which shows that the UV blocking modifiers promote the antiageing effects of asphalt. FTIR test reveals that the increment of carbonyl groups and sulfoxide groups of modified asphalt is less than that in base asphalt. Tests indicate the best UV blocking effect results for samples with LDHs and the worst UV blocking effect results for samples with CB.

78 FR 26847 - Including Specific Pavement Types in Federal-aid Highway Traffic Noise Analyses

Science.gov (United States)

2013-05-08

...: dense-graded asphaltic concrete (DGAC), open-graded asphaltic concrete (OGAC), and Portland cement... involved in what the highway noise industry refers to as ``low noise pavements'' or ``quieter pavements... several national workshops, trainings, and informational outreach pieces on this topic. In 2005, the FHWA...

Impact of the variation in dynamic vehicle load on flexible pavement responses

Science.gov (United States)

Ahsanuzzaman, Md

The purpose of this research was to evaluate the dynamic variation in asphalt pavement critical responses due to dynamic tire load variations. An attempt was also made to develop generalized regression equations to predict the dynamic response variation in flexible pavement under various dynamic load conditions. The study used an extensive database of computed pavement response histories for five different types of sites (smooth, rough, medium rough, very rough and severely rough), two different asphalt pavement structures (thin and thick) at two temperatures (70 °F and 104 °F), subjected to a tandem axle dual tire at three speeds 25, 37 and 50 mph (40, 60 and 80 km/h). All pavement responses were determined using the 3D-Move Analysis program (Version 1.2) developed by University of Nevada, Reno. A new term called Dynamic Response Coefficient (DRC) was introduced in this study to address the variation in critical pavement responses due to dynamic loads as traditionally measured by the Dynamic Load Coefficient (DLC). While DLC represents the additional varying component of the tire load, DRC represents the additional varying component of the response value (standard deviation divided by mean response). In this study, DRC was compared with DLC for five different sites based on the roughness condition of the sites. Previous studies showed that DLC varies with vehicle speed and suspension types, and assumes a constant value for the whole pavement structure (lateral and vertical directions). On the other hand, in this study, DRC was found to be significantly varied with the asphalt pavement and function of pavement structure, road roughness conditions, temperatures, vehicle speeds, suspension types, and locations of the point of interest in the pavement. A major contribution of the study is that the variation of pavement responses due to dynamic load in a flexible pavement system can be predicted with generalized regression equations. Fitting parameters (R2) in the

Impacts of pavement types on in-vehicle noise and human health.

Science.gov (United States)

Li, Qing; Qiao, Fengxiang; Yu, Lei

2016-01-01

Noise is a major source of pollution that can affect the human physiology and living environment. According to the World Health Organization (WHO), an exposure for longer than 24 hours to noise levels above 70 dB(A) may damage human hearing sensitivity, induce adverse health effects, and cause anxiety to residents nearby roadways. Pavement type with different roughness is one of the associated sources that may contribute to in-vehicle noise. Most previous studies have focused on the impact of pavement type on the surrounding acoustic environment of roadways, and given little attention to in-vehicle noise levels. This paper explores the impacts of different pavement types on in-vehicle noise levels and the associated adverse health effects. An old concrete pavement and a pavement with a thin asphalt overlay were chosen as the test beds. The in-vehicle noise caused by the asphalt and concrete pavements were measured, as well as the drivers' corresponding heart rates and reported riding comfort. Results show that the overall in-vehicle sound levels are higher than 70 dB(A) even at midnight. The newly overlaid asphalt pavement reduced in-vehicle noise at a driving speed of 96.5 km/hr by approximately 6 dB(A). Further, on the concrete pavement with higher roughness, driver heart rates were significantly higher than on the asphalt pavement. Drivers reported feeling more comfortable when driving on asphalt than on concrete pavement. Further tests on more drivers with different demographic characteristics, along highways with complicated configurations, and an examination of more factors contributing to in-vehicle noise are recommended, in addition to measuring additional physical symptoms of both drivers and passengers. While there have been many previous noise-related studies, few have addressed in-vehicle noise. Most studies have focused on the noise that residents have complained about, such as neighborhood traffic noise. As yet, there have been no complaints by

The Concrete and Pavement Challenge

Science.gov (United States)

Roman, Harry T.

2012-01-01

The modern world is characterized by the extensive use of concrete and asphalt pavement. Periodically, these materials are replaced and the old materials disposed of. In this challenge, students will be asked to develop ways to reuse the old materials. It is important for students to understand how concrete and asphalt are made and applied, as…

A FEM Modeling of the Concrete Pavement Made of the Recycling Material

Directory of Open Access Journals (Sweden)

Šešlija Miloš

2016-01-01

Full Text Available Paper is a brief review of the research focused on formulation an numerical model for the concrete pavement which is made by the recycling material. For numerical modeling the finite element model (FEM and the 3D finite element model were applied. The software EverFE 2.25, was used. The results of FEM analysis is in a chapter shape showing move value change, strees and deflections for all layers a construction road model. In the next phase of the research was provided by FEM software with appropriate general purpose non-linear models, which allows the analysis of the real behavior of solid pavement under load.

Load Response Analysis of Asphalt Pavement

Directory of Open Access Journals (Sweden)

Xiao Zhijun

2016-01-01

Full Text Available Based on the filed data of Fuzhou test road, load response regulation of nonlinear pavement structure was analyzed in this paper; Mechanics software was adopted to analyze linear elastic and nonlinear of the pavement structure, analyzed results and road filed data were compared, and determine the correlation between them and the field data.

Crack repair of asphalt concrete with induction energy

NARCIS (Netherlands)

García, A.; Schlangen, E.; Ven, M. van de; Vliet, D. van

2011-01-01

It is well known that the healing rates of asphalt courses increase with the temperature. A new method, induction heating, is used in this paper to increase the lifetime of asphalt concrete pavements. Mastic will be first made electrically conductive by the addition of conductive fibers. Then it

Aging Influence on Fatigue Characteristics of RAC Mixtures Containing Warm Asphalt Additives

Directory of Open Access Journals (Sweden)

Feipeng Xiao

2010-01-01

Full Text Available Aging is an important factor to affect the long-term performance of asphalt pavement. The fatigue life of a typical warm mix asphalt (WMA is generally related to various factors of rheological and mechanical properties of the mixture. The study of the fatigue behavior of the specific rubberized WMA is helpful in recycling the scrap tires and saving energy in terms of the conventional laboratory aging process. This study explores the utilization of the conventional fatigue analysis approach in investigating the cumulative dissipated, stiffness, and fatigue life of rubberized asphalt concrete mixtures containing the WMA additive after a long-term aging process. The aged beams were made with one rubber type (−40 mesh ambient crumb rubber, two aggregate sources, two WMA additives (Asphamin and Sasobit, and tested at 5 and 20ºC. A total of 55 aged fatigue beams were tested in this study. The test results indicated that the addition of crumb rubber extends the fatigue resistance of asphalt binder while WMA additive exhibits a negative effect. The study indicated that the WMA additive generally has an important influence on fatigue life. In addition, test temperature and aggregate source play an important role in determining the cumulative dissipated energy, stiffness, and fatigue life of an aged mixture.

Long-term Metal Performance of Three Permeable Pavements

Science.gov (United States)

EPA constructed a 4,000-m2 parking lot surfaced with three permeable pavements (permeable interlocking concrete pavers, pervious concrete, and porous asphalt) on the Edison Environmental Center in Edison, NJ in 2009. Samples from each permeable pavement infiltrate were collected...

Literature review : performance of RAP/RAS mixes and new direction.

Science.gov (United States)

2014-04-01

In the last several years reclaimed asphalt pavement (RAP) and recycled asphalt shingles (RAS) have been : widely used in asphalt mixes in Texas. The use of RAP/RAS can significantly reduce the initial cost of : asphalt mixtures, conserve energy, and...

Assessment of highway pavements using GPR

Science.gov (United States)

Plati, Christina; Loizos, Andreas

2015-04-01

Highway infrastructure is a prerequisite for a functioning economy and social life. Highways, often prone to congestion and disruption, are one of the aspects of a modern transport network that require maximum efficiency if an integrated transport network, and sustainable mobility, is to be achieved. Assessing the condition of highway structures, to plan subsequent maintenance, is essential to allow the long-term functioning of a road network. Optimizing the methods used for such assessment will lead to better information being obtained about the road and underlying ground conditions. The condition of highway structures will be affected by a number of factors, including the properties of the highway pavement, the supporting sub-base and the subgrade (natural ground), and the ability to obtain good information about the entire road structure, from pavement to subgrade, allows appropriate maintenance programs to be planned. The maintenance of highway pavements causes considerable cost and in many cases obstruction to traffic flow. In this situation, methods that provide information on the present condition of pavement structure non-destructively and economically are of great interest. It has been shown that Ground-Penetrating-Radar (GPR), which is a Non Destructive Technique (NDT), can deliver information that is useful for the planning of pavement maintenance activities. More specifically GPR is used by pavement engineers in order to determine physical properties and characteristics of the pavement structure, information that is valuable for the assessment of pavement condition. This work gives an overview on the practical application of GPR using examples from highway asphalt pavements monitoring. The presented individual applications of GPR pavement diagnostics concern structure homogeneity, thickness of pavement layers, dielectric properties of asphalt materials etc. It is worthwhile mentioning that a number of applications are standard procedures, either

Characterization of Failure and Permanent Deformation Behaviour of Asphalt Concrete

NARCIS (Netherlands)

Wang, J.G.

2015-01-01

Asphalt concrete is a viscoelastic material consisting of aggregates, filler and bitumen. The response of asphalt concrete is highly dependent on temperature, loading rate and confining pressure. Permanent deformation is one of the most important distresses developing during the flexible pavement

Appropriate models for estimating stresses and strains in asphalt layers

CSIR Research Space (South Africa)

Jooste, FJ

1998-09-01

Full Text Available The broad objective is to make recommendations for appropriate modelling procedures to be used in the structural design of asphalt layers. Findings of this investigation are intended to be used in refining and validating existing asphalt pavement...

Evaluating the mechanical performance of Very Thin Asphalt Overlay (VTAO as a sustainable rehabilitation strategy in urban pavements

Directory of Open Access Journals (Sweden)

M. Sol-Sánchez

2017-07-01

Full Text Available Very Thin Asphalt Overlay (VTAO has been introduced as an alternative to traditional thick overlays, seal coats, and micro-surfacings. Nonetheless, there are some challenges that still remain regarding the application of VTAOs (such as mixture type, cohesiveness, wear resistance, cracking and durability, particularly in heavy traffic urban areas. Therefore, this paper presents an extensive comparative evaluation of the mechanical performance, durability and safety issues (cohesiveness, adhesiveness, ageing, cracking, plastic deformation, permeability, macrotexture, skid and wear resistance, and fuel resistance of a VTAO (20 mm thick and a high performance BBTM 11B (35 mm thick, commonly used as an open-graded mixture for pavement overlays. The results demonstrated that VTAO is an appropriate material for urban pavements as it provides good durability and resistance to the propagation of defects. Nonetheless, further studies are required to improve its behavior under distresses related to plastic deformations and safety properties.

Evaluating the mechanical performance of Very Thin Asphalt Overlay (VTAO) as a sustainable rehabilitation strategy in urban pavements

International Nuclear Information System (INIS)

Sol-Sánchez, M.; García-Travé, G.; Ayar, P.; Moreno-Navarro, F.; Rubio-Gámez, M.C.

2017-01-01

Very Thin Asphalt Overlay (VTAO) has been introduced as an alternative to traditional thick overlays, seal coats, and micro-surfacings. Nonetheless, there are some challenges that still remain regarding the application of VTAOs (such as mixture type, cohesiveness, wear resistance, cracking and durability), particularly in heavy traffic urban areas. Therefore, this paper presents an extensive comparative evaluation of the mechanical performance, durability and safety issues (cohesiveness, adhesiveness, ageing, cracking, plastic deformation, permeability, macrotexture, skid and wear resistance, and fuel resistance) of a VTAO (20 mm thick) and a high performance BBTM 11B (35 mm thick), commonly used as an open-graded mixture for pavement overlays. The results demonstrated that VTAO is an appropriate material for urban pavements as it provides good durability and resistance to the propagation of defects. Nonetheless, further studies are required to improve its behavior under distresses related to plastic deformations and safety properties. [es

Operational properties of nanomodified stone mastic asphalt

OpenAIRE

Inozemtsev Sergey Sergeevich; Korolev Evgeniy Valer’evich

2015-01-01

In order to prolong the lifetime and to improve the quality of pavements made of asphalt concrete it is necessary to apply innovative solutions in the process of design of such building materials. In order to solve the problem of low durability of asphalt concrete a modifier was proposed, which consists of diatomite, iron hydroxide sol (III) and silica sol. Application of the diatomite with nanoscale layer of nanomodifier allows getting a stone mastic asphalt, which has high values of physica...

PROSPECTS FOR APPLICATION OF COMPLEX-MODIFIED SAND ASPHALT CONCRETE IN ROAD CONSTRUCTION

Directory of Open Access Journals (Sweden)

D. Yu. Alexandrov

2017-01-01

Full Text Available The paper considers a possibility to use sand asphalt concrete as a material for protection of asphalt concrete and cement concrete road pavements against affection of external destructive factors. Advantages and disadvantages of sand asphalt concrete road pavements have been determined in the paper. The paper provides recommendations on improvement of sand asphalt concrete properties and contains an analysis of possible variants for usage of complex-modified sand asphalt concrete in the road construction. It has been noted that according to its potentially possible physical and mechanical properties activated quartz sand being micro-reinforced by dispersive industrial wastes is considered as an efficient component for creation of constructive layers in road asphalt concrete pavements. The paper reveals only specific aspects of the efficient application of quartz sand in road asphalt concrete. The subject of the paper loоks rather interesting for regions where there are no rock deposits for obtaining broken-stone ballast but there is rather significant spreading of local quarts sand. Its successful application is connected with the necessity to develop special equipment for physical and chemical activation of sand grain surface that permits strongly to increase an adhesive strength in the area of phase separation within the “bitumen–SiO2” system. The considered problem is a topical one and its solution will make it possible to local sand in a maximum way and partially to exclude application of broken stone in road construction.

Self Healing of Asphalt Mixtures : Towards a Better Understanding of the Mechanism

NARCIS (Netherlands)

Qiu, J.

2012-01-01

Traffic is increasing rapidly in terms of number of vehicles and also in axle loads. In order to maximize the availability of the pavement and to minimize hindrances to traffic because of maintenance works, long life pavements are needed. An asphalt pavement with self repairing capabilities is

Long Life Pavements; Firmes de larga duracion

Energy Technology Data Exchange (ETDEWEB)

Mateos Moreno, A.; Marron Fernandez, J. O.; Perez Ayuso, J.

2009-07-01

The existence of long-life pavements is not new; they have been built in Europe and the United States for decades. In fact, the concept arises from the observation of in-service roads; it was verified how particular pavements, initially designed for a 20-year service life, did not seem to have reduced the bearing capacity along the time, and its maintenance necessities had been exclusively focused on the wearing course. The base idea of long-life pavements is the existence of a fatigue threshold below which the damage produced by each load application is, in practice, zero or below the healing potential of the asphalt mix. The use practice of long-life pavements design considers a pavements constituted by three asphalt layers, each one with a very specific role: a wearing course that provides with the surface characteristics, an intermediate course that provides with most of the structural capacity and a base course that provides with the fatigue resistance. Furthermore, one of the particularities is the design against specific distress mechanisms. Maintenance strategy also presents specific particularities for long-life pavements. It is essentially focused on the detection of surface deterioration, and the appropriate and timely repair, before the damage extends beyond the wearing course, putting into risk the structural integrity of the pavement. Nowadays, this new way to conceive the design, the construction and the maintenance of road pavements, constitutes one of the main challenges for pavement engineering worldwide. (Author) 5 refs.

Performance assessment of warm mix asphalt (WMA) pavements.

Science.gov (United States)

2009-09-01

Warm Mix Asphalt (WMA) is a new technology that was introduced in Europe in 1995. WMA offers several advantages over : conventional asphalt concrete mixtures, including: reduced energy consumption, reduced emissions, improved or more uniform : binder...

Some material and construction aspects regarding in situ recycling of road pavements in South Africa

CSIR Research Space (South Africa)

Paige-Green, P

2006-07-01

Full Text Available In situ recycling as a pavement rehabilitation option in South Africa is becoming increasingly important. Use has been made of both bitumen (emulsion and foamed) and traditional chemical stabilizers (lime, cement, lime/slagment, etc). Very little...

On the representative volume element of asphalt concrete at low temperature

Science.gov (United States)

Marasteanu, Mihai; Cannone Falchetto, Augusto; Velasquez, Raul; Le, Jia-Liang

2016-08-01

The feasibility of characterizing asphalt mixtures' rheological and failure properties at low temperatures by means of the Bending Beam Rheometer (BBR) is investigated in this paper. The main issue is the use of thin beams of asphalt mixture in experimental procedures that may not capture the true behavior of the material used to construct an asphalt pavement.

The use of Crumb Rubber as Substitute of Fine Aggregate for Hot Asphalt Mixture using Polymer Modified Bitumen

Science.gov (United States)

Setyawan, A.; Nugroho, S. K.; Irsyad, A. M.; Mutaqo, H. F.; Ramadhan, P.; Sumarsono, A.; Pramesti, F. P.

2018-03-01

The development of road pavement to fulfilled the need of modern life is not only focused on heavy duty road, but also a light duty road for the convenience of road users according to its function. For example the use of pavement on the jogging track, rail crossing, playground and so on. Due to the need of an alternative and the innovation of a comfortable pavement layer, but sufficiently strong in holding the load on the layer. The alternative innovation that can be used for the respective requirement is the utilization of waste old tires as substitute material in pavement construction. In this case the use of crumb rubber made from old tire rubber as an 100% fine aggregate substitute on the asphalt mixtures is investigated. To improve the strength and durability of the mixtures, the addition of polymer modified bitumen was incorporated. The two types of asphalt mixture selected in this study by using a continuous gradation of asphalt concrete and a gap gradation of hot roll asphalt. Testing to be implemented in this research is volumetric characteristics, Marshall characteristics, resistance to abrasion and impact and permeability. Replacement of fine aggregate with crumb rubber on asphalt concrete mixture with 60/70 penetration grade bitumen and polymer modified asphalt SBS E-55 in this research are expected to be an alternative in improving the quality of pavement and overcoming the environmental problems by reuse the waste materials.

Application of Finite Layer Method in Pavement Structural Analysis

Directory of Open Access Journals (Sweden)

Pengfei Liu

2017-06-01

Full Text Available The finite element (FE method has been widely used in predicting the structural responses of asphalt pavements. However, the three-dimensional (3D modeling in general-purpose FE software systems such as ABAQUS requires extensive computations and is relatively time-consuming. To address this issue, a specific computational code EasyFEM was developed based on the finite layer method (FLM for analyzing structural responses of asphalt pavements under a static load. Basically, it is a 3D FE code that requires only a one-dimensional (1D mesh by incorporating analytical methods and using Fourier series in the other two dimensions, which can significantly reduce the computational time and required resources due to the easy implementation of parallel computing technology. Moreover, a newly-developed Element Energy Projection (EEP method for super-convergent calculations was implemented in EasyFEM to improve the accuracy of solutions for strains and stresses over the whole pavement model. The accuracy of the program is verified by comparing it with results from BISAR and ABAQUS for a typical asphalt pavement structure. The results show that the predicted responses from ABAQUS and EasyFEM are in good agreement with each other. The EasyFEM with the EEP post-processing technique converges faster compared with the results derived from ordinary EasyFEM applications, which proves that the EEP technique can improve the accuracy of strains and stresses from EasyFEM. In summary, the EasyFEM has a potential to provide a flexible and robust platform for the numerical simulation of asphalt pavements and can easily be post-processed with the EEP technique to enhance its advantages.

Experiences from in-situ monitoring of pavement under weather conditions change

Directory of Open Access Journals (Sweden)

Likar Barbara

2016-01-01

Full Text Available Very strong winters with temperatures under 0°C and hot summers with temperatures more than 30°C are observed in the South East part of Slovenia. Those big differences in temperature during the year and especially temperatures below freezing point have strong influence on asphalt layer and sub base of road pavement. The freeze/thaw cycles lead to formation of ice lenses in base course causing cracks in asphalt layers and degrade the pavement usually in a few years. For this reason one section of the national road in the South East part of Slovenia was rebuilt with cold in-situ pavement retreatment. A test field with inbuilt sensors for measuring water content, temperature and deformation in various depths and locations was constructed during the remediation works to study the mechanism of freeze-thaw degradation of pavements. The main goal of the test field is to determine water content in sub base, freezing depth, temperature distribution and deformations, which lead to cracks in asphalt layer after the remediation work in the road construction.

Product (P1) from project 0-6738 : performance studies and future directions for mixes containing RAP and RAS.

Science.gov (United States)

2013-01-01

In recent years both reclaimed asphalt pavement (RAP) and recycled asphalt shingles (RAS) have been widely used in asphalt mixes by the asphalt paving industry in Texas. The use of RAP and RAS can save tax payers money, and it is also good for the...

Evaluation of various hot mix asphalt pavement thicknesses over rubblized concrete pavement.

Science.gov (United States)

2011-07-01

In 1999, the Wisconsin DOT constructed two test sections as part of a rubblized PCC pavement project on I-39 to evaluate whether : increased HMA thickness could extend the pavement system's service life. Design thicknesses of the control and test sec...

Investigation of Asphalt Mixture Creep Behavior Using Thin Beam Specimens

International Nuclear Information System (INIS)

Zofka, Adam; Marasteanu, Mihai; Turos, Mugur

2008-01-01

The asphalt pavement layer consists of two or more lifts of compacted asphalt mixture; the top of the layer is also exposed to aging, a factor that significantly affects the mixture properties. The current testing specifications use rather thick specimens that cannot be used to investigate the gradual change in properties with pavement depth. This paper investigates the feasibility of using the 3-point bending test with thin asphalt mixture beams (127x12.7x6.35 mm) to determine the low-temperature creep compliance of the mixtures. Several theoretical and semi-empirical models, from the theory of composites, are reviewed and evaluated using numerical and experimental data. Preliminary results show that this method can be used for low-temperature mixture characterization but several crucial factors need further inspection and interpretation

Laboratory assessment of the mechanical properties of bituminous mixes recycled in situ with cold bitumen processes

OpenAIRE

BROSSEAUD, Y; BEGHIN, A; PLACIN, F; GAUDEFROY, V; DELFOSSE, F; BAENA, J

2006-01-01

Dans le cadre du programme SCORE (Superior COld REcycling of asphalt pavements), contrat européen du 5ème PCRD, le LCPC a été le leader de la tache 7, concernant l'évaluation des propriétés mécaniques en laboratoire des enrobés recyclés en place au moyen de liants bitumineux à froid. Préalablement à l'étude, un essai croisé sur la détermination du module par traction indirecte a été entrepris entre les laboratoires impliqués dans cette tach pour évaluer les dispersions tant dans la préparatio...

Investigation of Warm Mix Asphalt (WMA) Technologies and Increased Percentages of Reclaimed Asphalt Pavement (RAP) in Asphalt Mixtures

Science.gov (United States)

2011-04-01

The implementation of warm-mix asphalt (WMA) is becoming more widespread with a growing number of contractors utilizing various WMA technologies. Early research suggests WMA may be more susceptible to moisture damage than traditional hot-mix asphalt ...

POROUS-MASTIC ASPHALT-CONCRETE MIXTURES AND THEIR UTILIZATION HISTORY

Directory of Open Access Journals (Sweden)

Khudokonenko Anton Aleksandrovich

2017-11-01

Full Text Available Subject: a rapid increase in the traffic intensity and freight traffic on motor roads leads to premature destruction of road surfaces. At the same time, the actual service life of asphalt-concrete pavements rarely exceeds 4-5 years and in most cases is only 2-3 years. Most intensively defects and fractures appear on asphalt-concrete pavements in the early spring. Nowadays the overhaul intervals for the road surface coverings are significantly lower than those given by the regulatory requirements. One of the main reasons for this phenomenon is the use of obsolete technologies based on traditional materials whose properties are inadequate to resist stresses and deformations arising in the coating. This is especially evident in the climatic conditions of the south of the European part of Russia, where the upper layers of the roadway experience a much wider range of temperatures. Tighter requirements for the initial road-building materials and timely repair of the coatings allow us to increase the service life of motor roads. Research objectives: the aim of the study is to develop a new type of asphalt-concrete, such as porous-mastic one. Materials and methods: the work was carried out based on observations and published sources, a method of theoretical study and analysis. Results: the domestic and foreign experience of using the given asphalt concrete for the top layer of the coating was considered. The technology of preparation and laying of a porous-mastic asphalt-concrete mixture is presented and its advantages and disadvantages are shown. Conclusions: increasing the longevity of highways is an important and urgent task and it can be solved, in particular, due to the wide use of new technologies and non-traditional building materials that allow us to improve the quality of asphalt-concrete pavement and prolong its overhaul intervals.

Aging of Asphalt Symposium, September 17th 2014, Delft, the Netherlands

NARCIS (Netherlands)

Erkens, S.M.J.G.; Scarpas, A.; Blab, R.; Glaser, R.; Glover, C.; Oeser, M.; Porot, L.; Soenen, H.

2015-01-01

Technical specifications for the asphalt concrete properties are developed to be able to specify mixtures that will perform well in pavement applications. Being able to identify and determine properties related to pavement performance in practice is crucial for both road authorities and contractors,

Aging of Asphalt Symposium : Delft, the Netherlands September 17th 2014

NARCIS (Netherlands)

Erkens, Sandra; Scarpas, Athanasios

2015-01-01

Technical specifications for the asphalt concrete properties are developed to be able to specify mixtures that will perform well in pavement applications. Being able to identify and determine properties related to pavement performance in practice is crucial for both road authorities and contractors,

Analysis of pavement serviceability for the Aashto Design Method: The Chilean Case

International Nuclear Information System (INIS)

Solminihac, Hernan De; Salsilli, R.; Bengoa, E.; Kohler, E.

2003-01-01

Serviceability is an indicator that represents the level of service a pavement provides to the users. This subjective opinion is closely related to objective aspects, which can be measured on the pavement's surface. This research aims specifically at relating serviceability results obtained by a 9-member evaluation panel, representing general public as closely as possible to parameters (particularly of roughness) measured within instruments on 30, 25 and 11 road sections of asphalt concrete, Portland cement concrete and asphalt overlay respectively. Results show that prediction of serviceability is quite accurate based on roughness evaluation, while also revealing that, by comparison to studies in more developed countries, Chileans are seemingly more tolerant, in that they assign a somewhat high rating to ride quality. Furthermore, visible distress does not have a significant influence on serviceability values for Chilean users. A ratio between International Roughness Index (IRI) and Serviceability, as defined by AASHTO, was developed and may be used in this design method. Results for the final pavement condition of urban pavements were obtained (IRI-asphalt final=5.9, IRI-concrete final=8.1). (author)

In situ determination of layer thickness and elastic moduli of asphalt pavement systems by spectral analysis of surface waves (SASW) method

International Nuclear Information System (INIS)

Mohd Azmi Ismail; Sri Atmaja Rosyidi; Abdul Rahim Samsudin; Abdul Ghani Rafek; Khairul Anuar Mohd Nayan

2003-01-01

Spectral analysis of surface waves (SASW) is a non-destructive and in situ method for determining the stiffness profile of soil and pavement sites. The method consists of generation, measurement, and processing of dispersive elastic waves in layered systems. The test is performed on the pavement surface at strain level below 0.001%, where the elastic properties are considered independent of strain amplitude. During an SASW test, the surface of the medium under investigation is subject to an impact to generate energy at various frequencies. Two vertical acceleration transducers are set up near the impact source to detect the energy transmitted through the testing media. By recording signals in digitised form using a data acquisition system and processing them, surface wave velocities can be determined by constructing a dispersion curve. Through forward modeling, the shear wave velocities can be obtained, which can be related to the variation of stiffness with depth. This paper presents the results of two case studies for near?surface profiling of two different asphalt pavement sites. (Author)

Thermal–moisture dynamics of embankments with asphalt pavement in permafrost regions of central Tibetan Plateau

Energy Technology Data Exchange (ETDEWEB)

Wen, Zhi; Zhang, Mingli; Ma, Wei; Wu, Qingbai; Niu, Fujun; Yu, Qihao; Fan, Zhaosheng; Sun, Zhizhong

2014-09-01

Subsurface moisture content is one of the critical factors that control the thermal dynamics of embankments. However, information on the subsurface moisture movement and distribution in embankments is still limited. To better understand the coupled water and heat transport within embankments, subsurface temperature and moisture of an asphalt pavement highway were extensively measured from 2009 to 2011. Collected data indicate that pure heat conduction is the overall main mechanism of heat transport in the embankment and heat convection plays a relatively unimportant role in heat transport. The results also indicate that subsurface moisture and temperature dynamics in the asphalt layer is strongly related to the rainfall events, while the subsurface moisture content below the road base course maintains relatively constant. Rainfall in summer leads to rapid cooling of the subsurface soil. Our results suggest that frequent and small rainfall events favour the thermal stability of the embankment due to the loss of latent heat of water evaporation. Moisture migration during freezing still occurred in the gravel fill and the water infiltrated into the active layer during thawing period. Freezing-induced water migration may result in the increase in water content of the embankment and the decrease in compactness of gravel fill.

Influence of Temperature Upon Permanent Deformation Parameters of Asphalt Concrete Mixes

Directory of Open Access Journals (Sweden)

Amjad Hamad Albayati

2017-07-01

Full Text Available The performance of asphalt concrete pavement has affected by many factors, the temperature is the most important environmental one which has a large effect on the structural behavior of flexible pavement materials. The main cause of premature failure of pavement is the rutting, Due to the viscoelastic nature of the asphalt cement, rutting is more pronounced in hot climate areas because the viscosity of the asphalt binder which is inversely related to rutting is significantly reduced with the increase in temperature resulting in a more rut susceptible paving mixtures. The objective of this study is to determine the effect of temperatures variations on the permanent deformation parameters (permanent strain (p, intercept (a, slope (b, Alpha and Mu as well as resilient strain (r and resilient modulus (Mr. To achieve this objective, one aggregate gradation with 12.5mm nominal maximum size, two grades of asphalt cements (40-50 and 60-70 brought form Al- Daurah refinery, limestone dust filler has been used to prepare the asphalt concrete mixtures. 30 Marshall specimens were prepared to determine the optimum asphalt cement content. Thereafter, 30 cylindrical asphalt concrete specimens (102mm in diameter and 203 mm in height are prepared in optimum asphalt cement and optimum ±0.5 percent. The prepared specimens were used in uniaxial repeated load test to evaluate the permanent deformation parameters of asphalt concrete mixes under the following testing temperature (5, 15, 25, 40 and 60c. The test result analyses appeared that Mr is decrease 51 percent when temperature increased from 5 c to 25 c and then decrease 22 percent with further increase in temperature from 25 c to 60 c. Also, the Alpha value decreases by a factor of 1.25 and 1.13 when temperature increases from 5 c to 25 c and 25 c to 60 c, espectively. Finally, statistical models were developed to predict the Alpha and Mu parameters of permanent deformation.

Mechanistic and Economical Characteristics of Asphalt Rubber Mixtures

Directory of Open Access Journals (Sweden)

Mena I. Souliman

2016-01-01

Full Text Available Load associated fatigue cracking is one of the major distress types occurring in flexible pavement systems. Flexural bending beam fatigue laboratory test has been used for several decades and is considered to be an integral part of the new superpave advanced characterization procedure. One of the most significant solutions to prolong the fatigue life for an asphaltic mixture is to utilize flexible materials as rubber. A laboratory testing program was performed on a conventional and Asphalt Rubber- (AR- gap-graded mixtures to investigate the impact of added rubber on the mechanical, mechanistic, and economical attributes of asphaltic mixtures. Strain controlled fatigue tests were conducted according to American Association of State Highway and Transportation Officials (AASHTO procedures. The results from the beam fatigue tests indicated that the AR-gap-graded mixtures would have much longer fatigue life compared with the reference (conventional mixtures. In addition, a mechanistic analysis using 3D-Move software coupled with a cost analysis study based on the fatigue performance on the two mixtures was performed. Overall, analysis showed that AR modified asphalt mixtures exhibited significantly lower cost of pavement per 1000 cycles of fatigue life per mile compared to conventional HMA mixture.

A comparison between linear and non-linear analysis of flexible pavements

Energy Technology Data Exchange (ETDEWEB)

Soleymani, H.R.; Berthelot, C.F.; Bergan, A.T. [Saskatchewan Univ., Saskatoon, SK (Canada). Dept. of Mechanical Engineering

1995-12-31

Computer pavement analysis programs, which are based on mathematical simulation models, were compared. The programs included in the study were: ELSYM5, an Elastic Linear (EL) pavement analysis program, MICH-PAVE, a Finite Element Non-Linear (FENL) and Finite Element Linear (FEL) pavement analysis program. To perform the analysis different tire pressures, pavement material properties and asphalt layer thicknesses were selected. Evaluation criteria used in the analysis were tensile strain in bottom of the asphalt layer, vertical compressive strain at the top of the subgrade and surface displacement. Results showed that FENL methods predicted more strain and surface deflection than the FEL and EL analysis methods. Analyzing pavements with FEL does not offer many advantages over the EL method. Differences in predicted strains between the three methods of analysis in some cases was found to be close to 100% It was suggested that these programs require more calibration and validation both theoretically and empirically to accurately correlate with field observations. 19 refs., 4 tabs., 9 figs.

Mathematical and experimental investigations of modeling, simulation and experiment to promote the life-cycle of polymer modified asphalt.

Science.gov (United States)

2014-07-01

The formulation of constitutive equations for asphaltic pavement is based on rheological models which include the asphalt mixture, additives, and the bitumen. In terms of the asphalt, the rheology addresses the flow and permanent deformation in time,...

Properties of sulfur-extended asphalt concrete

Directory of Open Access Journals (Sweden)

Gladkikh Vitaliy

2016-01-01

Full Text Available Currently, increased functional reliability of asphalt concrete coatings associated with various modifying additives that improve the durability of pavements. Promising builder is a technical sulfur. Asphalt concrete, made using a complex binder consisting of petroleum bitumen and technical sulfur, were calledsSulfur-Extended Asphalt Concrete. Such asphalt concrete, due to changes in the chemical composition of particulate and bitumen, changes the intensity of the interaction at the interface have increased rates of physical and mechanical properties. There was a lack of essential knowledge concerning mechanical properties of the sulfur-bituminous concrete with such an admixture; therefore, we had carried out the necessary examination. It is revealed that a new material satisfies local regulations in terms of compressive and tensile strength, shear resistance, and internal friction.

The study of stiffness modulus values for AC-WC pavement

Science.gov (United States)

Lubis, AS; Muis, Z. A.; Iskandar, T. D.

2018-02-01

One of the parameters of the asphalt mixture in order for the strength and durability to be achieved as required is the stress-and-strain showing the stiffness of a material. Stiffness modulus is a very necessary factor that will affect the performance of asphalt pavements. If the stiffness modulus value decreases there will be a cause of aging asphalt pavement crack easily when receiving a heavy load. The high stiffness modulus asphalt concrete causes more stiff and resistant to bending. The stiffness modulus value of an asphalt mixture material can be obtained from the theoretical (indirect methods) and laboratory test results (direct methods). For the indirect methods used Brown & Brunton method, and Shell Bitumen method; while for the direct methods used the UMATTA tool. This study aims to determine stiffness modulus values for AC-WC pavement. The tests were conducted in laboratory that used 3 methods, i.e. Brown & Brunton Method, Shell Bitumen Method and Marshall Test as a substitute tool for the UMATTA tool. Hotmix asphalt made from type AC-WC with pen 60/70 using a mixture of optimum bitumen content was 5.84% with a standard temperature variation was 60°C and several variations of temperature that were 30, 40, 50, 70 and 80°C. The stiffness modulus value results obtained from Brown & Brunton Method, Shell Bitumen Method and Marshall Test which were 1374,93 Mpa, 235,45 Mpa dan 254,96 Mpa. The stiffness modulus value decreases with increasing temperature of the concrete asphalt. The stiffness modulus value from the Bitumen Shell method and the Marshall Test has a relatively similar value.The stiffness modulus value from the Brown & Brunton method is greater than the Bitumen Shell method and the Marshall Test, but can not measure the stiffness modulus value at temperature above 80°C.

Chemomechanics of Damage Accumulation and Damage-Recovery Healing in Bituminous Asphalt Binders

NARCIS (Netherlands)

Pauli, A.T.

2014-01-01

As a contribution to the development of mutli-scale multi-physics approaches to modelling pavement performance, the present thesis considers the topic of damage accumulation accompanied by damage recover self-healing of the bituminous asphalt phase of pavement systems. It is found insightful that by

Adjusting Asphalt Mixes for Increased Durability and Implementation of a Performance Tester to Evaluate Fatigue Cracking of Asphalt

Science.gov (United States)

2018-01-17

Cracking is a common failure mechanism in asphalt concrete pavement structures. It is one of the main reasons for large road maintenance and rehabilitation expenditures, as well as reduced user comfort and increased fuel consumption due to high road ...

Rutting resistance of asphalt mixture with cup lumps modified binder

Science.gov (United States)

Shaffie, E.; Hanif, W. M. M. Wan; Arshad, A. K.; Hashim, W.

2017-11-01

Rutting is the most common pavement distress in pavement structures which occurs mainly due to several factors such as increasing of traffic volume, climatic conditions and also due to construction design errors. This failure reduced the service life of the pavement, reduced driver safety and increase cost of maintenance. Polymer Modified Binder has been observed for a long time in improving asphalt pavement performance. Research shows that the use of polymer in bituminous mix not only improve the resistance to rutting but also increase the life span of the pavement. This research evaluates the physical properties and rutting performance of dense graded Superpave-designed HMA mix. Two different types of dense graded Superpave HMA mix were developed consists of unmodified binder mix (UMB) and cup lumps rubber (liquid form) modified binder mix (CLMB). Natural rubber polymer modified binder was prepared from addition of 8 percent of cup lumps into binder. Results showed that all the mixes passed the Superpave volumetric properties criteria which indicate that these mixtures were good with respect to durability and flexibility. Furthermore, rutting results from APA rutting test was determined to evaluate the performance of these mixtures. The rutting result of CLMB demonstrates better resistance to rutting than those prepared using UMB mix. Addition of cup lumps rubber in asphalt mixture was found to be significant, where the cup lumps rubber has certainly improves the binder properties and enhanced its rutting resistance due to greater elasticity offered by the cup lumps rubber particles. It shows that the use of cup lumps rubber can significantly reduce the rut depth of asphalt mixture by 41% compared to the minimum rut depth obtained for the UMB mix. Therefore, it can be concluded that the cup lumps rubber is suitable to be used as a modifier to modified binder in order to enhance the properties of the binder and thus improves the performance of asphalt mixes.

Performance of Hot Mix Asphalt Mixture Incorporating Kenaf Fibre

Science.gov (United States)

Hainin, M. R.; Idham, M. K.; Yaro, N. S. A.; Hussein, S. O. A. E.; Warid, M. N. M.; Mohamed, A.; Naqibah, S. N.; Ramadhansyah, P. J.

2018-04-01

Kenaf fibre has been recognised to increase the strength of concrete, but its application in asphalt concrete is still unanswered. This research investigated the performance of Hot Mix Asphalt (HMA) incorporated with different percentages of kenaf fibre (0.1 %, 0.2% and 0.3% by weight of dry aggregate) in term of resilient modulus, rutting performance using Asphalt Pavement analyser (APA) and moisture damage using the Modified Lottman test (AASHTO-T283). The fibre was interweaved to a diameter of about 5-10 mm and length of 30 mm which is three times the nominal maximum aggregate size used in the mix. Asphaltic mixtures of asphalt concrete (AC) 10 were prepared and compacted using Marshall compactor which were subsequently tested to evaluate the resilient modulus and moisture susceptibility. Twelve cylindrical specimens (150mm diameter) from AC10, two control samples with two modified ones for each percentage of kenaf fibres compacted using Gyratory compactor were used for rutting test using APA. The laboratory results reveal that the addition of kenaf fibres slightly reduce the resilient modulus of the mixes and that asphaltic mix with 0.3% kenaf fibre can mitigate both rutting and moisture damage which makes the pavement more sustain to the loads applied even in the presence of water. 0.3% kenaf fibre content is considered to be the optimal content which had the least rut depth and the highest TSR of 81.07%. Based on grid analysis, addition of 0.3% kenaf fibre in asphaltic concrete was recommended in modifying the samples.

Improving rutting resistance of pavement structures using geosynthetics: an overview.

Science.gov (United States)

Mirzapour Mounes, Sina; Karim, Mohamed Rehan; Khodaii, Ali; Almasi, Mohammad Hadi

2014-01-01

A pavement structure consists of several layers for the primary purpose of transmitting and distributing traffic loads to the subgrade. Rutting is one form of pavement distresses that may influence the performance of road pavements. Geosynthetics is one type of synthetic materials utilized for improving the performance of pavements against rutting. Various studies have been conducted on using different geosynthetic materials in pavement structures by different researchers. One of the practices is a reinforcing material in asphalt pavements. This paper intends to present and discuss the discoveries from some of the studies on utilizing geosynthetics in flexible pavements as reinforcement against permanent deformation (rutting).

Improving Rutting Resistance of Pavement Structures Using Geosynthetics: An Overview

Directory of Open Access Journals (Sweden)

Sina Mirzapour Mounes

2014-01-01

Full Text Available A pavement structure consists of several layers for the primary purpose of transmitting and distributing traffic loads to the subgrade. Rutting is one form of pavement distresses that may influence the performance of road pavements. Geosynthetics is one type of synthetic materials utilized for improving the performance of pavements against rutting. Various studies have been conducted on using different geosynthetic materials in pavement structures by different researchers. One of the practices is a reinforcing material in asphalt pavements. This paper intends to present and discuss the discoveries from some of the studies on utilizing geosynthetics in flexible pavements as reinforcement against permanent deformation (rutting.

Mechanical behavior of flexible pavements undergoing thermal gradients - doi: 10.4025/actascitechnol.v33i3.10848

Directory of Open Access Journals (Sweden)

Grazielli Vassoler

2011-07-01

Full Text Available The proper structural understanding of a pavement should consider, according to the pavement mechanics, the aspects related to the traffic load, the environment and material properties. When asphaltic materials are used, the stress/strain relationships and the dependencies of load-time and temperature are key parameters for understanding flexible pavement performance. In this study, we employed the finite elements method to calculate stress/strain in flexible pavements structures considering temperature variation. The input data includes material stiffness, which is function of temperature and changes with position and time. The pavement temperature is obtained through the heat transfer differential equation, applying the Laplace transform and its numerical inversion. The finite elements grid was generated by the software ANSYS® and imported by the software MATLAB®. In order to determine the stiffness of the first layer (asphalt concrete we used the average of four nodes, depending on the each node temperature. The result evidences the importance of thermal gradients for the pavement analysis, both for the fatigue cracking and the accumulation of plastic deformations. The use of unique modulus for asphalt concrete layer generates results far from reality.

Evaluation system for CO2 emission of hot asphalt mixture

Directory of Open Access Journals (Sweden)

Bo Peng

2015-04-01

Full Text Available The highway construction industry plays an important role in economic and development, but is also a primary source of carbon emission. Accordingly, with the global climate change, energy conservation and reduction of carbon emissions have become critical issues in the highway construction industry. However, to date, a model for the highway construction industry has not been established. Hence, to implement a low-carbon construction model for highways, this study divided asphalt pavement construction into aggregate stacking, aggregate supply, and other stages, and compiled a list of energy consumption investigation. An appropriate calculation model of CO2 emission was then built. Based on the carbon emission calculation model, the proportion of carbon emissions in each stage was analyzed. The analytic hierarchy process was used to establish the system of asphalt pavement construction with a judgment matrix, thereby enabling calculation of the weight coefficient of each link. In addition, the stages of aggregate heating, asphalt heating, and asphalt mixture mixing were defined as key stages of asphalt pavement construction. Carbon emissions at these stages accounted for approximately 90% of the total carbon emissions. Carbon emissions at each stage and their impact on the environment were quantified and compared. The energy saving construction schemes as well as the environmental and socioeconomic benefits were then proposed. Through these schemes, significant reductions in carbon emissions and costs can be achieved. The results indicate that carbon emissions reduce by 32.30% and 35.93%, whereas costs reduce by 18.58% and 6.03%. The proposed energy-saving and emission reduction scheme can provide a theoretical basis and technical support for the development of low-carbon highway construction.

Validity of multiple stress creep recovery (MSCR) test for DOTD asphalt binder specification : technical summary.

Science.gov (United States)

2017-09-01

Higher traffic coupled with heavier loads led the asphalt industry to introduce polymer-modified binders to enhance the durability and strength of hot mix asphalt (HMA) pavements. When the Superpave Performance Graded (PG) binder specification (AASHT...

Determination of mechanical properties of materials used in WAY-30 test pavements.

Science.gov (United States)

2010-05-01

The US Route 30 bypass of Wooster, Ohio, in Wayne County, WAY-30, was constructed to demonstrate two types of : extended service pavements, a long-life Portland cement concrete (PCC) pavement on the eastbound lanes and an asphalt : concrete (AC...

Studying the Behavior of Asphalt Mix and Their Properties in the Presence of Nano Materials

OpenAIRE

Aman Patidar; Dipankar Sarkar; Manish Pal

2017-01-01

Due to rapid development, increase in the traffic load, higher traffic volume and seasonal variation in temperature, asphalt pavement shows distresses like rutting, fatigue and thermal cracking etc. because of this pavement fails during service life so that bitumen needs to be modified with some additive. In this study VG30 grade bitumen modify with addition of nanosilica with 1% to 5% (increment of 1%) by weight of bitumen. Hot mix asphalt (HMA) have higher mixing, laying and rolling tempera...

Caltrans use of scrap tires in asphalt rubber products: a comprehensive review

Directory of Open Access Journals (Sweden)

Haiping Zhou

2014-02-01

Full Text Available The California Department of Transportation (Caltrans has been using scrap tire rubber in asphalt pavements since the 1970s in chip seals and the 1980s in rubberized hot mix asphalt(RHMA. Both the wet (field blend and dry processes were used in early trials. Caltrans has also used rubber modified binders containing both crumb rubber modifier and polymer modifier that could be manufactured at a refinery facility, a terminal blend wet process. Since the beginning of this century, Caltrans increased the use of scrap tire rubber in paving projects and invested considerable resources in developing technically sound, cost effective, and environmentally friendly strategies for using scrap tire rubber in roadway applications. By the end of year 2010, approximately 31%of all hot mix asphalt (HMA placed by Caltrans was rubberized HMA, roughly 1.2 million tons. Caltrans efforts in using asphalt rubber products were also demonstrated in its research and technology development. These included the construction of two full-scale field experiments, five warranty projects, and an accelerated pavement study using a heavy vehicle simulator. Additionally, terminal blend asphalt rubber and rubberized warm mix asphalts began to be experimented on trial basis. This paper provides a comprehensive review of Caltrans experience over four decades with asphalt rubber products. Current practices and future outlook are also discussed.

Evaluation of pavement skid resistance using high speed texture measurement

Directory of Open Access Journals (Sweden)

Jay N. Meegoda

2015-12-01

Full Text Available Skid resistance is an important parameter for highway designs, construction, management, maintenance and safety. The purpose of this manuscript is to propose the correlation between skid resistance, which is measured as skid resistance trailer, and mean profile depth (MPD or the macro surface texture, which is measured by vehicle mounted laser, so that highway agencies can predict the skid resistance of pavement without the use of expensive and time consuming skid resistance trailer, which also causes disruption of traffic in use. In this research skid numbers and MPD from 5 new asphalt pavements and 4 old asphalt pavements were collected using a locked wheel skid trailer and a vehicle mounted laser. Using the data collected, a correlation between the skid number (SN40R collected by locked wheel skid tester and the texture data or MPD collected by a vehicle mounted laser operating at highway speeds was developed. The proposed correlation for new pavements was positive for MPD values less than 0.75 mm to reach a peak SN40R value, then there was a negative correlation as the MPD increases until the MPD value was equal to 1.1 mm and beyond the MPD value of 1.1 mm to the maximum value of 1.4 mm, SN40R value remained almost constant. There were significant data scatter for the MPD value of 0.8 mm. To explain these results, water film thickness during the friction test was calculated and the critical MPD was defined. The effect of sealed water pool on the SN40R was discussed. The test result showed a similar trend for older asphalt pavements, but with lower SN40R values due to the polishing of pavement micro-texture by traffic. Hence, a reduction factor was proposed for older pavements based on cumulative traffic volume for the above correlation to predict the skid resistance of older pavements.

Heavy Vehicle Simulator aided evaluation of overlays on pavements with active cracks

CSIR Research Space (South Africa)

Viljoen, AW

1987-07-01

Full Text Available their effects by means of field data from actual pavements. The South African Heavy Simulator was also used to evaluate a variety of conventional and innovative asphaltic overlays on a severely cracked concrete pavement of which the mechanisms and extent...

New Hampshire binder and mix review.

Science.gov (United States)

2012-08-01

This review was initiated to compare relative rut testing and simple performance tests (now known as Asphalt Mix : Performance Tests) for the New Hampshire inch mix with 15% Recycled Asphalt Pavement (RAP). The tested mixes were : made from ...

Development of indirect ring tension test for fracture characterization of asphalt mixtures

Science.gov (United States)

Zeinali Siavashani, Alireza

Low temperature cracking is a major distress in asphalt pavements. Several test configurations have been introduced to characterize the fracture properties of hot mix (HMA); however, most are considered to be research tools due to the complexity of the test methods or equipment. This dissertation describes the development of the indirect ring tension (IRT) fracture test for HMA, which was designed to be an effective and user-friendly test that could be deployed at the Department of Transportation level. The primary advantages of this innovative and yet practical test include: relatively large fracture surface test zone, simplicity of the specimen geometry, widespread availability of the required test equipment, and ability to test laboratory compacted specimens as well as field cores. Numerical modeling was utilized to calibrate the stress intensity factor formula of the IRT fracture test for various specimen dimensions. The results of this extensive analysis were encapsulated in a single equation. To develop the test procedure, a laboratory study was conducted to determine the optimal test parameters for HMA material. An experimental plan was then developed to evaluate the capability of the test in capturing the variations in the mix properties, asphalt pavement density, asphalt material aging, and test temperature. Five plant-produced HMA mixtures were used in this extensive study, and the results revealed that the IRT fracture test is highly repeatable, and capable of capturing the variations in the fracture properties of HMA. Furthermore, an analytical model was developed based on the viscoelastic properties of HMA to estimate the maximum allowable crack size for the pavements in the experimental study. This analysis indicated that the low-temperature cracking potential of the asphalt mixtures is highly sensitive to the fracture toughness and brittleness of the HMA material. Additionally, the IRT fracture test data seemed to correlate well with the data from

An In-Depth Investigation into the Physicochemical, Thermal, Microstructural, and Rheological Properties of Petroleum and Natural Asphalts

Directory of Open Access Journals (Sweden)

Nader Nciri

2016-10-01

Full Text Available Over the last decade, unexpected and sudden pavement failures have occurred in several provinces in South Korea. Some of these failures remain unexplained, further illustrating the gaps in our knowledge about binder chemistry. To prevent premature pavement distress and enhance road performance, it is imperative to provide an adequate characterization of asphalt. For this purpose, the current research aims at inspecting the chemistry, microstructure, thermal, and physico-rheological properties of two types of asphalt, namely petroleum asphalt (PA and natural asphalt (NA. The binders were extensively investigated by using elemental analysis, thin-layer chromatography with flame ionization detection (TLC-FID, matrix-assisted laser desorption ionization time-of-fight mass spectroscopy (MALDI-TOF-MS, Fourier transform infrared spectroscopy (FT-IR, Raman spectroscopy (RS, Nuclear magnetic resonance spectroscopy (1H-NMR, ultraviolet and visible spectroscopy (UV-VIS, X-ray diffraction (XRD, scanning electron microscopy (SEM, thermogravimetric analysis (TGA, differential scanning calorimetry (DSC, penetration, softening point, ductility, and viscosity tests. The findings of this research have revealed the distinct variations between the chemical compositions, microstructures, and thermo-rheological properties of the two asphalts and provided valuable knowledge into the characteristics of the binders. Such insight has been effective in predicting the performance or distress of road pavement. This paper will, therefore, be of immediate interest to materials engineers in state highway agencies and asphalt industries.

Effectiveness of noise barriers installed adjacent to transverse grooved concrete pavement : executive summary report.

Science.gov (United States)

2009-10-16

In recent years the Ohio Department of Transportation (ODOT) has reconstructed a number of roadways where asphalt pavements were replaced with concrete pavements which were finished with a random transverse grooved surface texture (ODOT specification...

Effects of cross-anisotropy and stress-dependency of pavement layers on pavement responses under dynamic truck loading

Directory of Open Access Journals (Sweden)

Rafiqul A. Tarefder

2016-06-01

Full Text Available Previous studies by the authors have determined pavement responses under dynamic loading considering cross-anisotropy in one layer only, either the cross-anisotropic viscoelastic asphalt concrete (AC layer or the cross-anisotropic stress-dependent base layer, but not both. This study evaluates pavement stress–strain responses considering cross-anisotropy in all layers, i.e. AC, base and subbase, using finite element modeling (FEM technique. An instrumented pavement section on Interstate I-40 near Albuquerque, New Mexico was used in ABAQUS framework as model geometry. Field asphalt cores were collected and tested in the laboratory to determine the cross-anisotropy (n-values defined by horizontal to vertical modulus ratio, and other viscoelastic parameters as inputs of the model incorporated through user defined material interface (UMAT functionality in ABAQUS. Field base and subbase materials were also collected and tested in the laboratory to determine stress-dependent nonlinear elastic model parameters, as inputs of the model, again incorporated through UMAT. The model validation task was carried out using field-measured deflections and strain values under falling weight deflectometer (FWD loads at the instrumented section. The validated model was then subjected to an actual truck loading for studying cross-anisotropic effects. It was observed that horizontal tensile strain at the bottom of the AC layer and vertical strains in all layers decreased with an increase in n-value of the asphalt layer, from n < 1 (anisotropy to n=1 (isotropy. This indicates that the increase in horizontal modulus caused the decrease in layer strains. It was also observed that if the base and subbase layers were considered stress-dependent instead of linear elastic unbound layers, the horizontal tensile strain at the bottom of the asphalt layer increased and vertical strains on top of the base and subbase also increased.

Practical experiences with new types of highly modified asphalt binders

Science.gov (United States)

Špaček, Petr; Hegr, Zdeněk; Beneš, Jan

2017-09-01

As a result of steadily increasing traffic load on the roads in the Czech Republic, we should be focused on the innovative technical solutions, which will lead to extending the life time of asphalt pavements. One of these ways could be the future use of bitumen with a higher degree of polymer modification. This paper discusses experience with comparison of new highly polymer modified asphalt binder type with conventional polymer modified asphalt binder and unmodified binder with penetration grade 50/70. There are compared the results of various types laboratory tests of asphalt binders, as well as the results of asphalt mixtures laboratory tests. The paper also mentions the experience with workability and compactability of asphalt mixture with highly polymer modified asphalt binder during the realization of the experimental reference road section by the Skanska company in the Czech Republic.

Investigation of warm-mix asphalt for Iowa roadways.

Science.gov (United States)

2013-09-01

Phase II of this study further evaluated the performance of plant-produced warm-mix asphalt (WMA) mixes by conducting : additional mixture performance tests at a broader range of temperatures, adding additional pavements to the study, comparing : vir...

Permeable Pavement Research - Edison, New Jersey

Science.gov (United States)

This presentation provides the background and summary of results collected at the permeable pavement parking lot monitored at the EPA facility in Edison, NJ. This parking lot is surfaced with permeable interlocking concrete pavers (PICP), pervious concrete, and porous asphalt. ...

Quantifying Evaporation and Evaluating Runoff Estimation Methods in a Permeable Pavement System

Science.gov (United States)

The U.S. Environmental Protection Agency constructed a 0.4-ha parking lot in Edison, New Jersey, that incorporated permeable pavement in the parking lanes which were designed to receive run-on from the impervious hot-mix asphalt driving lanes. Twelve lined permeable pavement sec...

Experimental pavement delineation treatments

Science.gov (United States)

Bryden, J. E.; Lorini, R. A.

1981-06-01

Visibility and durability of materials used to delineate shoulders and medians adjacent to asphalt pavements were evaluated. Materials evaluated were polysulfide and coal tar epoxies, one and two component polyesters, portland cement, acrylic paints, modified-alkyd traffic paint, preformed plastic tape, and thermoplastic markings. Neat applications, sand mortars, and surface treatments were installed in several geometric patterns including cross hatches, solid median treatments, and various widths of edge lines. Thermoplastic pavement markings generally performed very well, providing good visibility under adverse viewing conditions for at least 4 years. Thermoplastic 4 in. wide edge lines appear to provide adequate visibility for most conditions.

Prediction of performance and evaluation of flexible pavement rehabilitation strategies

Directory of Open Access Journals (Sweden)

Kang-Won Wayne Lee

2017-04-01

Full Text Available Five test sections with different additives and strategies were established to rehabilitate a State-maintained highway more effectively in Rhode Island (RI: control, calcium chloride, asphalt emulsion, Portland cement and geogrid. Resilient moduli of subgrade soils and subbase materials before and after full depth rehabilitation were employed as input parameters to predict the performance of pavement structures using AASHTOWare Pavement ME Design (Pavement ME software in terms of rutting, cracking and roughness. It was attempted to use Level 1 input (which includes traffic full spectrum data, climate data and structural layer properties for Pavement ME. Traffic data was obtained from a Weigh-in-Motion (WIM instrument and Providence station was used for collecting climatic data. Volumetric properties, dynamic modulus and creep compliance were used as input parameters for 19 mm (0.75 in. warm mix asphalt (WMA base and 12.5 mm (0.5 in. WMA surface layer. The results indicated that all test sections observed AC top-down (longitudinal cracking except Portland cement section which passed for all criteria. The order in terms of performance (best to worst for all test sections by Pavement ME was Portland cement, calcium chloride, control, geogrid, and asphalt emulsion. It was also observed that all test sections passed for both bottom up and top down fatigue cracking by increasing thickness of either of the two top asphalt layers. Test sections with five different base/subbase materials were evaluated in last two years through visual condition survey and measurements of deflection and roughness to confirm the prediction, but there was no serious distress and roughness. Thus these experiments allowed selecting the best rehabilitation/reconstruction techniques for the particular and/or similar highway, and a framework was formulated to select an optimal technique and/or strategy for future rehabilitation/reconstruction projects. Finally, guidelines for

Pavement structure mechanics response of flexible on semi-flexible overlay that based on the old cement concrete pavement damage

Directory of Open Access Journals (Sweden)

Jiang Ruinan

2015-01-01

Full Text Available The old cement pavement damage status directly affect the design of the paving renovation. Based on the state of the old road investigation, combined with the research data at home and abroad, use the control index that average deflection, deflection value and CBR value to determine the reasonable time to overlay. Draw up the typical pavement structure according to the principle of combination of old cement pavement overlay structure design, and calculated that the tensile stress and shear stress in asphalt layer ,semi-flexible layer and the tensile in the old cement pavement adopting BISA3.0 statics finite element analysis model when modulus in the old road was diminishing. Use the computed result to analyses the influence of old road damage condition the influence of pavement structure.

Thermal segregation of asphalt material in road repair

Directory of Open Access Journals (Sweden)

Juliana Byzyka

2017-08-01

Full Text Available This paper presents results from a field study of asphaltic pavement patching operations performed by three different contractors working in a total of ten sites. It forms part of an ongoing research programme towards improving the performance of pothole repairs. Thermal imaging technology was used to record temperatures of the patching material throughout the entire exercise, from the stage of material collection, through transportation to repair site, patch forming, and compaction. Practical complications occurring during patch repairs were also identified. It was found that depending on the weather conditions, duration of the travel and poor insulation of the transported hot asphalt mix, its temperature can drop as high as 116.6 °C over the period that the reinstatement team travel to the site and prepare the patch. This impacting is on the durability and performance of the executed repairs. Cold spots on the asphalt mat and temperature differentials between the new hot-fill asphalt mix and existing pavement were also identified as poorly compacted areas that were prone to premature failure. For example, over the five-minute period, the temperature at one point reduced by 33% whereas the temperatures of nearby areas decreased by 65% and 71%. A return visit to the repair sites, three months later, revealed that locations where thermal segregation was noted, during the patching operation, had failed prematurely.

Moisture damage susceptibility of asphalt mixtures: Experimental characterization and modelling

OpenAIRE

Varveri, A.

2017-01-01

A well-functioning, long-lasting and safe highway infrastructure network ensures the mobility of people and facilitates the transport of goods, promoting thus environmental, economic, and social sustainability. The development of sustainable highway infrastructure requires, among other activities, the construction of pavement systems with enhanced durability. Moisture damage in asphalt pavements is associated with inferior performance, unexpected failures and reduced service life. All of thes...

Application of locally developed pavement temperature prediction algorithms in performance grade (PG) binder selection

CSIR Research Space (South Africa)

Denneman, E

2007-07-01

Full Text Available . Superior Performing Asphalt Pavements (SUPERPAVE): The product of the SHRP asphalt research program, Report no: SHRP-A-410, Strategic Highway Research Program, Washington. McGennis, R.B., Anderson, R.M., Kennedy, T.W., Solaimanian, M., 1995... international performance based specifications. Asphalt news, Vol. 19, Issue 2. Viljoen, A. W., 2001, Estimating Asphalt temperatures from air temperatures and basic sky parameters. Internal report, Transportek, CSIR, Pretoria. Williamson, R.H., and Kirby, W...

A simple test procedure for evaluating low temperature crack resistance of asphalt concrete : executive summary report.

Science.gov (United States)

2009-03-01

Low temperature cracking is one of the major : distress modes in asphalt pavement and is : disastrous to pavement performance and service : life. A poor riding surface leads to an increase in : maintenance and eventual early replacement of : the pave...

Application of viscoelastic continuum damage approach to predict fatigue performance of Binzhou perpetual pavements

Directory of Open Access Journals (Sweden)

Wei Cao

2016-04-01

Full Text Available For this study, the Binzhou perpetual pavement test sections constructed in Shandong Province, China, were simulated for long-term fatigue performance using the layered viscoelastic pavement analysis for critical distresses (LVECD finite element software package. In this framework, asphalt concrete was treated in the context of linear viscoelastic continuum damage theory. A recently developed unified fatigue failure criterion that defined the boundaries of the applicable region of the theory was also incorporated. The mechanistic modeling of the fatigue mechanisms was able to accommodate the complex temperature variations and loading conditions of the field pavements in a rigorous manner. All of the material models were conveniently characterized by dynamic modulus tests and direct tension cyclic fatigue tests in the laboratory using cylindrical specimens. By comparing the obtained damage characteristic curves and failure criteria, it is found that mixtures with small aggregate particle sizes, a dense gradation, and modified asphalt binder tended to exhibit the best fatigue resistance at the material level. The 15-year finite element structural simulation results for all the test sections indicate that fatigue performance has a strong dependence on the thickness of the asphalt pavements. Based on the predicted location and severity of the fatigue damage, it is recommended that Sections 1 and 3 of the Binzhou test sections be employed for perpetual pavement design.

Assessment of Quality of Asphalt Concrete used in Road ...

African Journals Online (AJOL)

OLUWASOGO

subjected to bitumen extraction and sieve analysis, hot mix Marshall Stability and flow tests, penetration and ... asphalt concrete as well as other structures of the flexible pavement. ... High-quality road networks are very important to the.

THE FATIGUE DURABILITY OF THE MODIFIED ASPHALT CONCRETE UNDER THE EFFECT OF INTENSIVE TRAFFIC LOADS

Directory of Open Access Journals (Sweden)

Yuri KALGIN

2016-06-01

Full Text Available The problem of prediction of the service life of asphalt concrete surface constructed with modified asphalt concrete application onto a traffic lane is examined. Asphalt concrete behaviour in road surface under the traffic loads was analysed. There were shown The results of experiments and their mathematical analysis of the assessment of standard and modified cold asphalt concrete fatigue life on road surface were shown. The service life of an asphalt concrete surface covered with standard and modified cold asphalt concrete is examined. The prediction has been received with an account of stress relaxation processes in asphalt concrete pavement and unevenness of traffic load application.

Incorporating the transverse profile of the wearing course into the control of the hot in-place recycling of asphalt concrete

Science.gov (United States)

Makowska, Michalina; Huuskonen-Snicker, Eeva; Alanaatu, Pauli; Aromaa, Kalle; Savarnya, Abhishek; Pellinen, Terhi; Das, Animesh

2018-05-01

The hot in-place recycling (HIR) of asphalt concrete (AC) is one of the least CO2 emissive reuse techniques. It allows for 100% reuse of material in-situ in the same application, at a reduced need for the material transport to and back from the construction site, as well as the reduced price in comparison with the fresh wearing course overlay. Finland uses the technique predominantly to fill wheel path ruts caused by the studded tire abrasion, to retain structural capacity and prevent hydroplaning. During the HIR process, the aged AC material is heated up in-situ, milled to the approximate depth of 40 mm, blended with fresh AC admixture and rejuvenator. However, the amount of the aged material and the amount of the aged bitumen that undergoes rejuvenation depends on the pavement transverse profile. The rut depth, width and shape determine the minimum volume of admixture necessary for refill during the process in order to retain the structural capacity, as well as the amount of the aged binder requiring rejuvenation. In favor of achieving homogenous rheological properties in the final product, the proportion between the aged binder and the fresh binder should be controlled, as it influences the required amount of rejuvenator. Therefore, the rut cross-sectional area and furthermore, the rut volume is one of the previously unrecognized or ignored major variables of the hot in-place recycling process in Finland that should be incorporated to the HIR process control. This article demonstrates the methodology of incorporating the transverse road profile measurements by 17 vehicle-mounted laser sensors into the calculation of required rejuvenator amounts. This can be done during the procurement preparation phase or during the paving work as a continuous in-situ process control. In the rheological optimization the apparent Newtonian viscosity concept and the rotational viscosity are utilized in the viscosity based blending equation, which then allows the use of oily

Effectiveness of pavement-solar energy system – An experimental study

International Nuclear Information System (INIS)

Zhou, Zhihua; Wang, Xiaojuan; Zhang, Xiaoyan; Chen, Guanyi; Zuo, Jian; Pullen, Stephen

2015-01-01

Highlights: • We built a small-scale pilot project of pavement-solar energy utilization. • Design an automatic monitoring system to record the operating data. • The average heat absorptivity of pavement-solar energy is 37%. • The average thermal storage effectiveness of the system is 17%. - Abstract: A small-scale pilot project was built for the pavement-solar energy utilization in this paper. An automatic data acquisition system was designed to measure the effectiveness of the pavement solar energy system based on the operation data of 24 h a day in both summer and winter. Through 69 days (1656 h) of operation in summer, 2821 kW h of heat energy were stored in soil underground. In the transitional season, 4598 kW h of heat energy were taken out from soil during 104 days (2496 h) of operation in winter. The analysis showed that in summer, solar heat collection of asphalt pavement could effectively reduce 7 °C of its temperature. Under conditions of natural radiation, the average heat absorptivity of pavement was 37% and the average thermal storage effectiveness of the system was 17%. The electrical energy consumed by the system is only 11% of stored heat. During the winter, the asphalt pavement absorbs heat from underground soil which effectively increases its temperature, cutting 32% days of surface temperature below the freezing point. This not only save the energy for ice/snow removal but also mitigate associated safety risks

Mechanical characterization of porous asphalt mixes modified with fatty acid amides -FAA-

Directory of Open Access Journals (Sweden)

Vanessa Senior Arrieta

2017-01-01

Full Text Available Porous asphalt mixes (PAM, form a special road surface for asphalt pavement structures, have a special particle size distribution that lets infiltrate to the runoff storm water through of it because of its voids content about 20 %. Many researchers conducted studies and have concluded that the use of modified asphalts is completely necessary to design PAM. Organic and chemical additives and special procedures as foamed asphalt have enhanced the performance of PAM, during their service life. This paper is focused on the mechanical characterization of PAM and how the asphalt modified with fatty acid amides, influenced on their behavior and performance. Based on an experimental methodology with laboratory tests aimed at establishing a comparison between porous asphalt mixes, using for its design and production a penetration 60-70 pure asphalt and another one asphalt modified with fatty acid amides.

Effect of moisture and freeze-thaw on mechanical properties of CRM asphalt mixture

Energy Technology Data Exchange (ETDEWEB)

Kim, Nak-Seok; Cho, Kee-Ju [Kyonggi University, Suwon(Korea)

2000-06-30

This paper presents the experimental test results on moisture and freeze-thaw resistance of hot mix crumb rubber modified (CRM) asphalt concrete mixture. To compare the differences in mechanical properties of conventional and CRM asphalt concretes, various tests were conducted under different moisture conditions and freeze-thaw cycles. Marshall mix design was also performed to determine the optimum asphalt contents for the both asphalt concrete mixtures. Test results revealed that the moisture and freeze-thaw resistance of CRM asphalt mixture was superior to the conventional asphalt concrete. As a result, it is considered that the utilization of waste tires in asphalt pavements has the potential of minimizing the damage due to the moisture and freeze-thaw. (author). 9 refs., 4 tabs., 8 figs.

Stabilized fiber-reinforced pavement base course with recycled aggregate

Science.gov (United States)

Sobhan, Khaled

's assumptions for rigid pavements), which has been found to explain reasonably well the field behavior of unreinforced and fiber-reinforced concrete slabs on grade. Finally, a preliminary cost analysis demonstrated that the use of stabilized recycled aggregate instead of a standard crushed stone base course can result in a meaningful economic savings.

Evaluation of MIT-SCAN-T2 for thickness quality control for PCC and HMA pavements : research project capsule.

Science.gov (United States)

2013-04-01

Thickness is currently a pay item for portland cement concrete (PCC) pavements : and a quality control item for both PCC and hot mix asphalt (HMA) pavements. : A change in pavement thickness of 0.5 in. can result in a reduction of multiple : years of...

Thermal Properties of Asphalt Mixtures Modified with Conductive Fillers

Directory of Open Access Journals (Sweden)

Byong Chol Bai

2015-01-01

Full Text Available This paper investigates the thermal properties of asphalt mixtures modified with conductive fillers used for snow melting and solar harvesting pavements. Two different mixing processes were adopted to mold asphalt mixtures, dry- and wet-mixing, and two conductive fillers were used in this study, graphite and carbon black. The thermal conductivity was compared to investigate the effects of asphalt mixture preparing methods, the quantity, and the distribution of conductive filler on thermal properties. The combination of conductive filler with carbon fiber in asphalt mixture was evaluated. Also, rheological properties of modified asphalt binders with conductive fillers were measured using dynamic shear rheometer and bending beam rheometer at grade-specific temperatures. Based on rheological testing, the conductive fillers improve rutting resistance and decrease thermal cracking resistance. Thermal testing indicated that graphite and carbon black improve the thermal properties of asphalt mixes and the combined conductive fillers are more effective than the single filler.

Experimental Investigations of Effect of Sulphur on Beach Sand–Fly Ash–Asphalt (S-F-A) Paving Mixes

OpenAIRE

Satyakumar, M.; Satheeshchandran, R.

2013-01-01

The main components of the flexible pavements are asphalt and aggregates. But in most of the places in India there is shortage of the good quality aggregates (especially coarse aggregates), at the same time beach sand is available in plenty in many regions. Due to relative abundance of beach sand, the studies on the utilities of the beach sand in paving mixes are worth taking up. But beach Sand-Asphalt mix alone is not suitable for pavement construction, because of its low stability and high ...

Fatigue Life Prediction of High Modulus Asphalt Concrete Based on the Local Stress-Strain Method

Directory of Open Access Journals (Sweden)

Mulian Zheng

2017-03-01

Full Text Available Previously published studies have proposed fatigue life prediction models for dense graded asphalt pavement based on flexural fatigue test. This study focused on the fatigue life prediction of High Modulus Asphalt Concrete (HMAC pavement using the local strain-stress method and direct tension fatigue test. First, the direct tension fatigue test at various strain levels was conducted on HMAC prism samples cut from plate specimens. Afterwards, their true stress-strain loop curves were obtained and modified to develop the strain-fatigue life equation. Then the nominal strain of HMAC course determined using finite element method was converted into local strain using the Neuber method. Finally, based on the established fatigue equation and converted local strain, a method to predict the pavement fatigue crack initiation life was proposed and the fatigue life of a typical HMAC overlay pavement which runs a risk of bottom-up cracking was predicted and validated. Results show that the proposed method was able to produce satisfactory crack initiation life.

The shakeout scenario: Meeting the needs for construction aggregates, asphalt, and concrete

Science.gov (United States)

Langer, W.H.

2011-01-01

An Mw 7.8 earthquake as described in the ShakeOut Scenario would cause significantdamage to buildings and infrastructure. Over 6 million tons of newly mined aggregate would be used for emergency repairs and for reconstruction in the five years following the event. This aggregate would be applied mostly in the form of concrete for buildings and bridges, asphalt or concrete for pavement, and unbound gravel for applications such as base course that goes under highway pavement and backfilling for foundations and pipelines. There are over 450 aggregate, concrete, and asphalt plants in the affected area, some of which would be heavily damaged. Meeting the increased demand for construction materials would require readily available permitted reserves, functioning production facilities, a supply of cement and asphalt, a source of water, gas, and electricity, and a trained workforce. Prudent advance preparations would facilitate a timely emergency response and reconstruction following such an earthquake. ?? 2011, Earthquake Engineering Research Institute.

Ground penetrating radar evaluation of new pavement density.

Science.gov (United States)

2015-02-01

The objective of this project was to map pavement surface density variations using dielectric : measurements from ground penetrating radar (GPR). The work was carried out as part of an : Asphalt Intelligent Compaction demonstration project on SR 539 ...

Assessing Asphalt and Concrete Pavement Surface Texture in the Field

OpenAIRE

Saad I. Sarsam; Huda N. Al Shareef

2016-01-01

The incorporation of safety characteristics into the traditional pavement structural design or in the functional evaluation of pavement condition has not been established yet. The design has focused on the structural capacity of the roadway so that the pavement can withstand specific level of repetitive loading over the design life. On the other hand, the surface texture condition was neither included in the AASHTO design procedure nor in the present serviceability index measurements. The ...

Pavement mechanic response of sulfate saline soil subgrade section based on fluid–structure interaction model

Directory of Open Access Journals (Sweden)

Xueying Zhao

2017-11-01

Full Text Available It is a consensus that salt heaving and frost heaving are urgent and typical distress in the sulfate saline soil area. To further investigate the microscopic performance of pavement structure in this special area, Jinan-Dongying Freeway in Shandong Province is selected as a case study engineering and the mechanic responses under salt heaving, frost heaving and traffic loads were analyzed through the finite element (FE Program (ANSYS. In this paper, the process of salt heaving and frost heaving was divided into 3 stages and FE models were established based on fluid–structure interaction (FSI model. It is shown that under both effects of salt heaving and frost heaving, the tensile stress of asphalt surface course could be up to 96.75% of its tensile strength, which means its tensile strength was seriously inadequate; however, traffic loads could help to dramatically counteract effects of salt heaving and frost heaving, which could decrease 40–80% of the tensile stress in asphalt surface course. It is also shown that in Jinan-Dongying Freeway effects of salt heaving had slightly larger effects on pavement compared with that of frost heaving, probably because salt heaving occurred from the top to the bottom of subgrade. However, as a whole, in sulfate saline soil area, compared with general area, crack resistance of asphalt courses and foundation treatment should always be strengthened. Keywords: Sulfate saline soil subgrade, Asphalt pavement, Pavement mechanic, FEM, FSI, Cracks and bulging

Rutting based evaluation of asphalt mixes

International Nuclear Information System (INIS)

Khan, K.M.

2012-01-01

Pavement rutting is one of the most common and destructive pavement distresses being observed in flexible pavements, which is primarily due to a-x-le loads that exceed legal limit and high ambient temperatures, and also poor mix design is one of the cause of rutting. The drastic increase in traffic volume during last few decades has resulted in premature pavement fillers of almost the whole road structure in Pakistan. In this scenario it is the time to investigate this problem and propose appropriate solution. Physical properties of aggregates and bitumen were evaluated in the laboratory. Mechanical Properties of three mixes. i.e., Marshall, Super pave and Stone Mastic Asphalt (SMA) were evaluated by performing creep test. indirect tensile test and dynamic modulus in order to compare the performance of mixes under prevailing load and environmental conditions of Pakistan. The study revealed that Super pave mixes performed better than Marshall and SMA. (author)

Development of an Overlay Design Procedure for Composite Pavements

Science.gov (United States)

2017-09-01

The composite overlay design procedure currently used by ODOT sometimes produces very large overlay thicknesses that are deemed structurally unnecessary, especially for composite pavements already with thick asphalt overlays. This study was initiated...

"Full-Scale Testing of Pavement Response"

DEFF Research Database (Denmark)

Ullidtz, Per; Ekdahl, Peter

1998-01-01

Three pavement sections in southern Sweden were instrumented in late 1991. Each section have instruments for measuring the strain at the bottom of the asphalt layer, vertical stress and strains in the subgrade and temperatures at different depths. The purpose was to evaluate different theoretical...... methods for determining stresses, strains and deflections in pavement structurers.Falling Weight Deflectometer (FWD) test were done on the test sections, and stresses and strains were measured both under FWD loading and under a rolling wheel load. Different back-analysis procedures were used to derive...

LOW-NOISE PAVEMENT AS A WAY OF LIMITATION OF TRAFFIC NOISE LEVEL

Directory of Open Access Journals (Sweden)

Władysław Gardziejczyk

2014-11-01

Full Text Available Road surface can significantlyreduce the trafficnoise level. Depending on the characteristic of the upper surface layers the differences between the maximum rolling noise levels from passing vehicles to reach values about 10 dB (A. A special group is low-noise pavements characterized by the presence of voids above 15%. Application the porous asphalt layers or asphalt mixture type BBTM affects a significantreduction the width of land surrounded the roads where permissible equivalent sound level is exceeded. Such solutions in some cases can replace acoustic barriers. Road pavements with a higher content of voids require proper maintenance because their acoustic performances are reduced during operation.

Steel slag in hot mix asphalt concrete : final report

Science.gov (United States)

2000-04-01

In September 1994, steel slag test and control sections were constructed in Oregon to evaluate the use of steel slag in hot mix asphalt concrete (HMAC). This report covers the construction and five-year performance of a pavement constructed with 30% ...

Risk management of low air void asphalt concrete mixtures.

Science.gov (United States)

2013-07-01

Various forms of asphalt pavement distress, such as rutting, shoving and bleeding, can be attributed, in many cases, to low air voids in : the mixtures during production and placement. The occurrence of low air void contents during plant production m...

Research on construction technology for orthotropic steel deck pavement of Haihe River Chunyi Bridge

Science.gov (United States)

Xue, Y. C.; Qian, Z. D.; Zhang, M.

2017-01-01

In order to ensure the good service quality of orthotropic steel deck pavement of Haihe River Chunyi Bridge in Tianjin, and to reduce the occurrence of pavement diseases like lateral and longitudinal cracks, the key working procedures such as steel deck cleaning, anticorrosive coating, bonding layer spraying, seam cutting, epoxy asphalt concrete’s mixing, transportation, paving and compaction were studied. The study was based on the main features of epoxy asphalt concrete which is the pavement materials of Haihe River Chunyi Bridge, and combined with the basic characteristics and construction conditions of Haihe River Chunyi Bridge. Furthermore, some processing measures like controlling time and temperature, continuous paving with two pavers, lateral feeding, and improving the compaction method were proposed. The project example shows that the processing measures can effectively solve the technical difficulties in the construction of orthotropic steel deck pavement of Haihe River Chunyi Bridge, can greatly improve the construction speed and quality, and can provide reference for the same kinds of orthotropic steel deck pavement construction.

Synthesis and Characterization of New ‎Copolymers as Asphalt Additives

Directory of Open Access Journals (Sweden)

Firyal M. ‎ A

2017-12-01

Full Text Available Rheological properties of asphalt S50  were improved by adding different prepared copolymers as additives with high homogeneity of asphalts  samples.  Three types of copolymers were prepared  Poly  (Indene –Co- maleic anhydride(A1 Poly (Acrylonitrile –Co- Maleic anhydride (A2 and Poly (Dipentine –Co-Maleic anhydride (A3, the cross linking of (A3 to (A3d. by using sulfur.              These copolymers  were designed by inserting Maleic anhydride as  rings  containing through backbone of polymer chains to be high potentially to react with water to protect the crack of pavement .And moisture with inhibit bonding of crack of pavement, Many factors should be considered when prepared the additives to enhanced performance to be convenience cost, beneficial thermal safety ,   extended life of the asphalt, preparing conditions which gave high thermal resistance with more stabilities, all these prepared copolymer have been characterized by FTIR and H-NMR spectroscopies .Intrinsic viscosities were calculated. softening point and penetration were observed for all asphalts blends which were  compared with the  asphalt samples, which gave high thermal resistance with more stabilities.                                          The results  showed high properties of these blends when  compared with the original asphalt. The physical properties of a specific polymers are determined by the sequence and chemical structure , When polymers are added to asphalt , the properties of the modified asphalt cement depend on polymer characteristic of asphalt and compatibility of polymer with asphalt. All these prepared copolymers were tested by softening points and penetration for all  asphalt blends which were compared with the asphalt sample. All the Improvements made by adding polymers to asphalt included the Increasing the viscosity of the binder service, the thermal susceptibility of the binder

Engineering characterisation of epoxidized natural rubber-modified hot-mix asphalt.

Directory of Open Access Journals (Sweden)

Ramez A Al-Mansob

Full Text Available Road distress results in high maintenance costs. However, increased understandings of asphalt behaviour and properties coupled with technological developments have allowed paving technologists to examine the benefits of introducing additives and modifiers. As a result, polymers have become extremely popular as modifiers to improve the performance of the asphalt mix. This study investigates the performance characteristics of epoxidized natural rubber (ENR-modified hot-mix asphalt. Tests were conducted using ENR-asphalt mixes prepared using the wet process. Mechanical testing on the ENR-asphalt mixes showed that the resilient modulus of the mixes was greatly affected by testing temperature and frequency. On the other hand, although rutting performance decreased at high temperatures because of the increased elasticity of the ENR-asphalt mixes, fatigue performance improved at intermediate temperatures as compared to the base mix. However, durability tests indicated that the ENR-asphalt mixes were slightly susceptible to the presence of moisture. In conclusion, the performance of asphalt pavement can be enhanced by incorporating ENR as a modifier to counter major road distress.

Effect of Co-Production of Renewable Biomaterials on the Performance of Asphalt Binder in Macro and Micro Perspectives.

Science.gov (United States)

Qu, Xin; Liu, Quan; Wang, Chao; Wang, Dawei; Oeser, Markus

2018-02-06

Conventional asphalt binder derived from the petroleum refining process is widely used in pavement engineering. However, asphalt binder is a non-renewable material. Therefore, the use of a co-production of renewable bio-oil as a modifier for petroleum asphalt has recently been getting more attention in the pavement field due to its renewability and its optimization for conventional petroleum-based asphalt binder. Significant research efforts have been done that mainly focus on the mechanical properties of bio-asphalt binder. However, there is still a lack of studies describing the effects of the co-production on performance of asphalt binders from a micro-scale perspective to better understand the fundamental modification mechanism. In this study, a reasonable molecular structure for the co-production of renewable bio-oils is created based on previous research findings and the observed functional groups from Fourier-transform infrared spectroscopy tests, which are fundamental and critical for establishing the molecular model of bio-asphalt binder with various biomaterials contents. Molecular simulation shows that the increase of biomaterial content causes the decrease of cohesion energy density, which can be related to the observed decrease of dynamic modulus. Additionally, a parameter of Flexibility Index is employed to characterize the ability of asphalt binder to resist deformation under oscillatory loading accurately.

Effect of Co-Production of Renewable Biomaterials on the Performance of Asphalt Binder in Macro and Micro Perspectives

Directory of Open Access Journals (Sweden)

Xin Qu

2018-02-01

Full Text Available Conventional asphalt binder derived from the petroleum refining process is widely used in pavement engineering. However, asphalt binder is a non-renewable material. Therefore, the use of a co-production of renewable bio-oil as a modifier for petroleum asphalt has recently been getting more attention in the pavement field due to its renewability and its optimization for conventional petroleum-based asphalt binder. Significant research efforts have been done that mainly focus on the mechanical properties of bio-asphalt binder. However, there is still a lack of studies describing the effects of the co-production on performance of asphalt binders from a micro-scale perspective to better understand the fundamental modification mechanism. In this study, a reasonable molecular structure for the co-production of renewable bio-oils is created based on previous research findings and the observed functional groups from Fourier-transform infrared spectroscopy tests, which are fundamental and critical for establishing the molecular model of bio-asphalt binder with various biomaterials contents. Molecular simulation shows that the increase of biomaterial content causes the decrease of cohesion energy density, which can be related to the observed decrease of dynamic modulus. Additionally, a parameter of Flexibility Index is employed to characterize the ability of asphalt binder to resist deformation under oscillatory loading accurately.

The effect of loading time on flexible pavement dynamic response: a finite element analysis

Science.gov (United States)

Yin, Hao; Solaimanian, Mansour; Kumar, Tanmay; Stoffels, Shelley

2007-12-01

Dynamic response of asphalt concrete (AC) pavements under moving load is a key component for accurate prediction of flexible pavement performance. The time and temperature dependency of AC materials calls for utilizing advanced material characterization and mechanistic theories, such as viscoelasticity and stress/strain analysis. In layered elastic analysis, as implemented in the new Mechanistic-Empirical Pavement Design Guide (MEPDG), the time dependency is accounted for by calculating the loading times at different AC layer depths. In this study, the time effect on pavement response was evaluated by means of the concept of “pseudo temperature.” With the pavement temperature measured from instrumented thermocouples, the time and temperature dependency of AC materials was integrated into one single factor, termed “effective temperature.” Via this effective temperature, pavement responses under a transient load were predicted through finite element analysis. In the finite element model, viscoelastic behavior of AC materials was characterized through relaxation moduli, while the layers with unbound granular material were assumed to be in an elastic mode. The analysis was conducted for two different AC mixtures in a simplified flexible pavement structure at two different seasons. Finite element analysis results reveal that the loading time has a more pronounced impact on pavement response in the summer for both asphalt types. The results indicate that for reasonable prediction of dynamic response in flexible pavements, the effect of the depth-dependent loading time on pavement temperature should be considered.

Turning Back Time : Rheological and Microstructural Assessment of Rejuvenated Bitumen

NARCIS (Netherlands)

Nahar, S.N.; Schmets, A.J.M.; Schlangen, E.; Shirazi, M.; van de Ven, M.F.C.; Schitter, G.; Scarpas, A.

2014-01-01

Countermeasures to the ageing of bituminous asphalt binders is a highly important topic, both for service-life extension of asphalt ‘in the field’ and for recycling old pavements (RAP) into new structures with similar functional requirements as the original structure. Usually this is achieved by

Comparative field permeability measurement of permeable pavements using ASTM C1701 and NCAT permeameter methods.

Science.gov (United States)

Li, Hui; Kayhanian, Masoud; Harvey, John T

2013-03-30

Fully permeable pavement is gradually gaining support as an alternative best management practice (BMP) for stormwater runoff management. As the use of these pavements increases, a definitive test method is needed to measure hydraulic performance and to evaluate clogging, both for performance studies and for assessment of permeability for construction quality assurance and maintenance needs assessment. Two of the most commonly used permeability measurement tests for porous asphalt and pervious concrete are the National Center for Asphalt Technology (NCAT) permeameter and ASTM C1701, respectively. This study was undertaken to compare measured values for both methods in the field on a variety of permeable pavements used in current practice. The field measurements were performed using six experimental section designs with different permeable pavement surface types including pervious concrete, porous asphalt and permeable interlocking concrete pavers. Multiple measurements were performed at five locations on each pavement test section. The results showed that: (i) silicone gel is a superior sealing material to prevent water leakage compared with conventional plumbing putty; (ii) both methods (NCAT and ASTM) can effectively be used to measure the permeability of all pavement types and the surface material type will not impact the measurement precision; (iii) the permeability values measured with the ASTM method were 50-90% (75% on average) lower than those measured with the NCAT method; (iv) the larger permeameter cylinder diameter used in the ASTM method improved the reliability and reduced the variability of the measured permeability. Copyright © 2013 Elsevier Ltd. All rights reserved.

Evaluating The Performance of Asphalt Concrete Mixes by Utilizing Carbon Black as Asphalt Modifier

Directory of Open Access Journals (Sweden)

Aliaa Faleh Al.ani

2018-02-01

Full Text Available Carbon black produced from several factories in Iraq is expected to provide a reinforcing agent for asphalt paving materials. Carbon black has many characteristics that distinguish  it from conventional mineral fillers, as well as their different function in pavement mixtures. Theory and exercise advanced  in the inclusive utilize of carbon black as a reinforcing agent for rubber has led to concept of asphalt reinforcement. The very fine particles of micro filler added in different contents will be dispersed in asphalt cement improving the mechanical properties of asphalt concrete mixes. In this Four percentages rates were utilized; 0, 3, 6, and 9 percent adding to asphalt grade (60-70. Mixes of asphalt concrete were destined at their optimum asphalt content (OAC then experienced to assess their engineering characteristics that contain moisture of damage, permanent deformation, modulus of resilient and characteristics of fatigue. These characteristics have been assessed utilizing indirect tensile strength, uniaxial repeated loading and repeated flexural beam tests. Mixtures improved with carbon black were existed to have amended permanent deformation and fatigue characteristics, else exhibited high resilient modulus and lower moisture susceptibility. Result showed that a rate changed from 3 to 9 percent has shown an increase in resilient modulus for increment of carbon black and modulus of resilient for mixes with 9 percent carbon black was 1.4 times that for mixes with 0 percent carbon black. The altering of carbon black from a range (3-9 percent has modified the fatigue property of the asphalt concrete mixes as determined by flexural test, Significantly, to modify the asphalt concrete manner taken the  percent of carbon black 6, and to produce the mixes more durable , higher resistance to distresses by adding the local knowledge.

The Potential of Heat Collection from Solar Radiation in Asphalt Solar Collectors in Malaysia

Science.gov (United States)

Beddu, Salmia; Talib, Siti Hidayah Abdul; Itam, Zarina

2016-03-01

The implementation of asphalt solar collectors as a means of an energy source is being widely studied in recent years. Asphalt pavements are exposed to daily solar radiation, and are capable of reaching up to 70°C in temperature. The potential of harvesting energy from solar pavements as an alternative energy source in replace of non-renewable energy sources prone to depletion such as fuel is promising. In Malaysia, the sun intensity is quite high and for this reason, absorbing the heat from sun radiation, and then utilizing it in many other applications such as generating electricity could definitely be impressive. Previous researches on the different methods of studying the effect of heat absorption caused by solar radiation prove to be quite old and inaffective. More recent findings, on the otherhand, prove to be more informative. This paper focuses on determining the potential of heat collection from solar radiation in asphalt solar collectors using steel piping. The asphalt solar collector model constructed for this research was prepared in the civil engineering laboratory. The hot mixed asphalt (HMA) contains 10% bitumen mixed with 90% aggregates of the total size of asphalt. Three stainless steel pipes were embedded into the interior region of the model according to the design criteria, and then put to test. Results show that harvesting energy from asphalt solar collectors proves highly potential in Malaysia due its the hot climate.

Life cycle assessment of asphalt pavement maintenance.

Science.gov (United States)

2014-01-01

This study aims at developing a life cycle assessment (LCA) model to quantify the impact of pavement preservation on energy consumption and greenhouse gas (GHG) emissions. The construction stage contains material, manufacture, transportation and plac...

Life Cycle Assessment of Pavements: A Critical Review of Existing Literature and Research

Energy Technology Data Exchange (ETDEWEB)

Santero, Nicholas; Masanet, Eric; Horvath, Arpad

2010-04-20

This report provides a critical review of existing literature and modeling tools related to life-cycle assessment (LCA) applied to pavements. The review finds that pavement LCA is an expanding but still limited research topic in the literature, and that the existing body of work exhibits methodological deficiencies and incompatibilities that serve as barriers to the widespread utilization of LCA by pavement engineers and policy makers. This review identifies five key issues in the current body of work: inconsistent functional units, improper system boundaries, imbalanced data for asphalt and cement, use of limited inventory and impact assessment categories, and poor overall utility. This review also identifies common data and modeling gaps in pavement LCAs that should be addressed in future work. These gaps include: the use phase (rolling resistance, albedo, carbonation, lighting, leachate, and tire wear and emissions), asphalt fumes, feedstock energy of bitumen, traffic delay, the maintenance phase, and the end-of-life phase. This review concludes with a comprehensive list of recommendations for future research, which shed light on where improvements in knowledge can be made that will benefit the accuracy and comprehensiveness of pavement LCAs moving forward.

Ageing evolution of foamed warm mix asphalt combined with reclaimed asphalt pavement; Evolución del envejecimiento en mezclas espumadas semicalientes con áridos reciclados

Energy Technology Data Exchange (ETDEWEB)

Perez-Martinez, M.; Marsac, P.; Gabet, T.; Pouget, S.; Hammoum, F.

2017-07-01

The combination of high rates of reclaimed asphalt pavement (RAP) and warm mix asphalt (WMA) technologies is still ambiguous in terms of durability. With the aim of clarifying this issue, a study comparing a hot mix asphalt with a WMA prepared using the foaming process technology. Both mixes contain 50% of RAP and are submitted to a laboratory ageing procedure. The long term related performance of the mixtures is compared by means of complex modulus and fatigue testing. Penetration and ring and ball tests are undertaken on the recovered bitumens, as well as the ageing evolution, characterised by the Fourier Transform Infrared analysis. Finally, the Apparent Molecular Weight Distribution (AMWD) of the binders is calculated from rheological measurements using the δ-method. Results show a relation between ageing evolution and mechanical performance. After ageing, the overall tendencies are similar for both processes. [Spanish] El comportamiento de mezclas asfálticas semicalientes (WMA) con alto contenido de material reciclado (RAP) es aún incierto a largo plazo. Por este motivo, en este estudio se compara el envejecimiento una mezcla caliente convencional y una mezcla espumada semicaliente con 50% de RAP. Ambas mezclas han sido sometidas a un proceso de envejecimiento en laboratorio. La respuesta a largo plazo se ha comparado a través de los ensayos de módulo de rigidez y de fatiga. En los betunes recuperados se han llevado a cabo los ensayos de penetración y anillo-bola, así como el seguimiento del envejecimiento a través del análisis de infrarrojos. Finalmente, la distribución de peso molecular aparente (AMWD) de los betunes se ha calculado a través de medidas reológicas usando el “δ-method”. En los resultados se observa una relación entre la evolución del envejecimiento y su respuesta mecánica, donde la tendencia general es similar para ambas técnicas.

Performance Assessment of Warm Mix Asphalt (WMA) Pavements : Executive Summary Report

Science.gov (United States)

2009-09-01

Warm Mix Asphalt (WMA) is a new technology which was : introduced in 1995 in Europe. WMA is gaining attention all : over the world because it offers several advantages over : conventional asphalt concrete mixes. The benefits include: : (1) Reduced en...

Optimization of Asphalt Mixture Design for the Louisiana ALF Test Sections

Science.gov (United States)

2018-05-01

This research presents an extensive study on the design and characterization of asphalt mixtures used in road pavements. Both mixture volumetrics and physical properties obtained from several laboratory tests were considered in optimizing the mixture...

Use of warm mix asphalt pavement on Route 9, in Durham.

Science.gov (United States)

2012-06-01

A number of new technologies have been developed to lower the production and placement temperatures : of hot-mix asphalt (HMA). Generically, these technologies are referred to as warm-mix asphalt (WMA). : In Europe and to a lesser extent in North Ame...

Nitrogen Transformations in Three Types of Permeable Pavement

Science.gov (United States)

In 2009, USEPA constructed a 0.4-ha (1-ac) parking lot at the Edison Environmental Center in Edison, NJ, that incorporated three different permeable pavement types - permeable interlocking concrete pavers (PICP), pervious concrete (PC), and porous asphalt (PA). The driving lanes...

Preparation of Flame Retardant Modified with Titanate for Asphalt Binder

Directory of Open Access Journals (Sweden)

Bo Li

2014-01-01

Full Text Available Improving the compatibility between flame retardant and asphalt is a difficult task due to the complex nature of the materials. This study explores a low dosage compound flame retardant and seeks to improve the compatibility between flame retardants and asphalt. An orthogonal experiment was designed taking magnesium hydroxide, ammonium polyphosphate, and melamine as factors. The oil absorption and activation index were tested to determine the effect of titanate on the flame retardant additive. The pavement performance test was conducted to evaluate the effect of the flame retardant additive. Oxygen index test was conducted to confirm the effect of flame retardant on flame ability of asphalt binder. The results of this study showed that the new composite flame retardant is more effective in improving the compatibility between flame retardant and asphalt and reducing the limiting oxygen index of asphalt binder tested in this study.

INFLUENCE OF POLYMERIC-DISPERSED REINFORCEMENT ADDITIVES ON THE PERFORMANCE CHARACTERISTICS OF ASPHALT CONCRETE

Directory of Open Access Journals (Sweden)

Chernov Sergey Anatolevych

2017-07-01

Full Text Available The technique and results of the studies of the influence of a polymeric-dispersed reinforcement additive on the performance characteristics of road hot asphalt concrete, namely, its resistance to fatigue failures, rutting and development of residual deformation are described. It is shown that the proposed method of modification of asphalt-concrete mixtures ensures an increase in the durability of layers of pavement road surface.

Cost-benefit analysis of the construction of different flexible pavement structures considering the axle load and type of binder

Directory of Open Access Journals (Sweden)

Lucas Dotto Bueno

2016-08-01

Full Text Available The status of Brazilian highways reflects a deficient pavement performance when they are subjected to loadings imposed by heavy traffic. Current legislation, as enacted by Contran (National Traffic Council, has increased the axle weight limit for cargo vehicles by up to 10%. Therefore, the aim of this study was to determine a cost-benefit ratio by using different types of structures, asphalt binders and load intensities. Typical pavements were determined and then analyzed by the software AEMC (SisPav to obtain the horizontal tensile strain (εt values at the bottom of the asphalt concrete layer and, later, the NFATIGUE value. It was found that the increase in weight, within values covered by legislation, might result in a reduction of approximately 50% in the NFATIGUE value for the pavement structures analyzed. As for economic impact, the same weight increase caused a mean increase of 120% in the cost of repeated loading on pavement structures (R$ NFATIGUE-1. It was also observed that structures with more robust asphalt concrete layers can provide the best R$ NFATIGUE-1 ratios. The best results for granular materials were found with thinner layers, associated with a thicker coating. The benefits of modified binders were shown by the analyses of the best structural options: both the polymer-modified binder and the rubber asphalt binder offer significant structural and economic improvements to the structure.

Monitoring hot mix asphalt temperature to improve homogeneity and pavement quality

NARCIS (Netherlands)

ter Huerne, Henderikus L.; Miller, Seirgei Rosario; Doree, Andries G.; Santagata, E.

2009-01-01

This paper describes how controlled compaction practices lead to better quality asphalt. Therefore, it is important that during compaction operations the mixture is at a suitable temperature in order to achieve the specified degree of compaction. The University of Twente’s Asphalt Paving Research

Non-destructive system to evaluate critical properties of asphalt compaction : [research brief].

Science.gov (United States)

2013-12-01

The Wisconsin Highway Research Program sponsored a two-stage investigation to develop a non-destructive system to evaluate critical compaction properties and characteristics of asphalt pavements during the densification process. Stage One activities ...

Use of Adhesion Promoters in Asphalt Mixtures

Directory of Open Access Journals (Sweden)

Cihlářová Denisa

2018-03-01

Full Text Available The purpose of asphalt binder as a significant binder in road constructions is to permanently bind aggregates of different compositions and grain sizes. The asphalt binder itself does not have suitable adhesiveness, so after a period of time, bare grains can appear. This results in a gradual separation of the grains from an asphalt layer and the presence of potholes in a pavement. Adhesion promoters or adhesive agents are important and proven promoters in practice. They are substances mainly based on the fatty acids of polyamides which should increase the reliability of the asphalt’s binder adhesion to the aggregates, thus increasing the lifetime period of the asphalt mixture as well as its resistance to mechanical strain. The amount of a promoter or agent added to the asphalt mixture is negligible and constitutes about 0.3% of the asphalt’s binder weight. Nevertheless, even this quantity significantly increases the adhesive qualities of an asphalt binder. The article was created in cooperatation with the Slovak University of Technology, in Bratislava, Slovakia, and focuses on proving the new AD2 adhesive additive and comparing it with the Addibit and Wetfix BE promoters used on aggregates from the Skuteč - Litická and Bystřec quarries.

Misturas asfálticas recicladas a quente com incorporação de elevado percentual de fresado como alternativa para camada de módulo elevado

Directory of Open Access Journals (Sweden)

Iran Gomes da Rocha Segundo

2016-12-01

Full Text Available The high modulus asphalt mixtures (EME are constituted by an asphalt binder of low penetration and aggregates that have a dense grading curve providing high resistance to permanent deformation and shear stresses. The recycled hot mixtures asphalt (RHMA with the incorporation of high percentage of reclaimed asphalt pavement (RAP have potential for the use as an alternative material for the mentioned technique (EME. Its viability is given by the fact that the RAP oxidized binder has higher stiffness (low penetration, and also by the economy that can be achieve with the use of raw material from recycling with potential lower cost. This paper presents a study of the potential use of different RHMA with high percentages of RAP as a base and intermediate course of pavements, such as: (i Mixture I, composed exclusively by RAP as aggregate; (ii Mixture II, composed by 75% of RAP and 25% of natural aggregates; (iii Mixture III, composed by 75% of RAP and 25% of asphalt plant refuse aggregates. Thus, besides the characterization of these materials in the laboratory, computational analyzes were performed based on the Finite Element Method (FEM. The values of displacements, deformations and stresses obtained for the different asphalt pavement structures composed by these mixtures were evaluated and, from that, the traffic that they were able to withstand was calculated. The results showed that the high RAP RHMA could compose structures that can be used on medium and high volume traffic roads.

Multiscale imaging and characterization of the effect of mixing temperature on asphalt concrete containing recycled components.

Science.gov (United States)

Cavalli, M C; Griffa, M; Bressi, S; Partl, M N; Tebaldi, G; Poulikakos, L D

2016-10-01

When producing asphalt concrete mixture with high amounts of reclaimed asphalt pavement (RAP), the mixing temperature plays a significant role in the resulting spatial distribution of the components as well as on the quality of the resulting mixture, in terms of workability during mixing and compaction as well as in service mechanical properties. Asphalt concrete containing 50% RAP was investigated at mixing temperatures of 140, 160 and 180°C, using a multiscale approach. At the microscale, using energy dispersive X-ray spectroscopy the RAP binder film thickness was visualized and measured. It was shown that at higher mixing temperatures this film thickness was reduced. The reduction in film thickness can be attributed to the loss of volatiles as well as the mixing of RAP binder with virgin binder at higher temperatures. X-ray computer tomography was used to characterize statistically the distribution of the RAP and virgin aggregates geometric features: volume, width and shape anisotropy. In addition using X-ray computer tomography, the packing and spatial distribution of the RAP and virgin aggregates was characterized using the nearest neighbour metric. It was shown that mixing temperature may have a positive effect on the spatial distribution of the aggregates but did not affect the packing. The study shows a tendency for the RAP aggregates to be more likely distributed in clusters at lower mixing temperatures. At higher temperatures, they were more homogeneously distributed. This indicates a higher degree of blending both at microscale (binder film) and macroscale (spatial distribution) between RAP and virgin aggregates as a result of increasing mixing temperatures and the ability to quantify this using various imaging techniques. © 2016 The Authors Journal of Microscopy © 2016 Royal Microscopical Society.

Volatilization of polycyclic aromatic hydrocarbons from coal-tar-sealed pavement

Science.gov (United States)

Van Metre, Peter C.; Majewski, Michael S.; Mahler, Barbara J.; Foreman, William T.; Braun, Christopher L.; Wilson, Jennifer T.; Burbank, Teresa L.

2012-01-01

Coal-tar-based pavement sealants, a major source of PAHs to urban water bodies, are a potential source of volatile PAHs to the atmosphere. An initial assessment of volatilization of PAHs from coal-tar-sealed pavement is presented here in which we measured summertime gas-phase PAH concentrations 0.03 m and 1.28 m above the pavement surface of seven sealed (six with coal-tar-based sealant and one with asphalt-based sealant) and three unsealed (two asphalt and one concrete) parking lots in central Texas. PAHs also were measured in parking lot dust. The geometric mean concentration of the sum of eight frequently detected PAHs (ΣPAH8) in the 0.03-m samples above sealed lots (1320 ng m-3) during the hottest part of the day was 20 times greater than that above unsealed lots (66.5 ng m-3). The geometric mean concentration in the 1.28-m samples above sealed lots (138 ng m-3) was five times greater than above unsealed lots (26.0 ng m-3). Estimated PAH flux from the sealed lots was 60 times greater than that from unsealed lots (geometric means of 88 and 1.4 μg m-2 h-1, respectively). Although the data set presented here is small, the much higher estimated fluxes from sealed pavement than from unsealed pavement indicate that coal-tar-based sealants are emitting PAHs to urban air at high rates compared to other paved surfaces.

Effects of preparation process on performance of rubber modified asphalt

Science.gov (United States)

Liu, Hanbing; Luo, Guobao; Wang, Xianqiang; Jiao, Yubo

2015-06-01

The rational utilization of waste rubber tire is essential for the environmental protection. Utilizing rubber particles to modify asphalt can not only improve asphalt performance, but also help the recycling of waste materials. Considering the effect of different preparation process parameters on the performance of rubber modified asphalt, this paper analyzes the effects of the shear temperature, shear time and shear rate on the performance of rubber modified asphalt, and provided a reference for its preparation.

Performances of Metal Concentrations from Three Permeable Pavement Infiltrates

Science.gov (United States)

The U.S. Environmental Protection Agency designed and constructed a 4000-m2 parking lot in Edison, New Jersey in 2009. The parking lot is surfaced with three permeable pavements: permeable interlocking concrete pavers, pervious concrete, and porous asphalt. Water sampling was con...

Investigation on seasonal variation of thermal-induced strain in flexible pavements based on field and laboratory measurements

Directory of Open Access Journals (Sweden)

Simita Biswas

2016-09-01

Full Text Available Pavement temperature variation has a large influence on the structural response of flexible pavements. Daily and seasonal temperature fluctuation causes expansion and contraction of pavement material, which then leads to the generation of thermal strain. In this study, field observation and laboratory tests were conducted to investigate seasonal variation of thermal-induced strain in flexible pavement. Field observations were conducted at the Integrated Road Research Facility (IRRF’s test road in Edmonton, Alberta, Canada, which is fully equipped with structural and environmental monitoring instruments. The main objective of the field study was to compare the variation of thermal-induced strain in warm and cold seasons. Field results indicated that thermal-induced strain is 1.4–2.0 times greater in cold seasons than in warm seasons following the same pavement temperature variations; however, strain generation rate was greater in warm seasons. Laboratory testing of asphalt slab and cylindrical samples produced comparable ratios. Moreover, field observation and laboratory testing showed a similar trend of temperature and thermal strain variations. Keywords: Thermal-induced strain, Asphalt strain gauge, Field observation, Flexible pavement, Laboratory testing, Seasonal variation

Detection of semi-volatile organic compounds in permeable pavement infiltrate

Science.gov (United States)

Abstract The Edison Environmental Center (EEC) performs research on green infrastructure (GI) treatment options. One such treatment option is the use of permeable pavements. EEC constructed a parking lot comprised of three different permeable systems: permeable asphalt, porous ...

Effects of street tree shade on asphalt concrete pavement performance

Science.gov (United States)

E.G. McPherson; J. Muchnick

2005-01-01

Forty-eight street segments were paired into 24 high-and low-shade pairs in Modesto, California, U.S. Field data were collected to calculate a Pavement Condition Index (PCI) and Tree Shade Index (TSI) for each segment. Statistical analyses found that greater PCI was associated with greater TSI, indicating that tree shade was partially responsible for reduced pavement...

Perpetual pavement – absorbing stress and functional maintenance

Directory of Open Access Journals (Sweden)

Rong Gao

2017-03-01

Full Text Available Perpetual Pavement combines the well documented smoothness and safety advantages of asphalt with an advanced, multi-layer paving design process, that with routine maintenance, extends the useful life of a roadway. Perpetual provides long lasting road and smoothness for the construction purposes. This study has the design key points of perpetual pavement based on the idea of life cycle, which has a new direction for the new highway construction, reconstruction and expansion. First, the structure of long life pavement design is studied to analyze the effect of stress absorbing layer. Second, researches on stress absorbing layer from the aspects of raw materials, mix proportion are implemented. Third, the design index of stress absorbing layer is determined by the shear strength test. The results show that the design idea of composite perpetual pavement can be realized by reasonable design of the stress absorbing layer and carrying out the surface functional maintenance can ensure the pavement to avoid structural damage in the operation stage.

ICP experiments more durable pavements

International Nuclear Information System (INIS)

Carta Petrolera

1994-01-01

A new asphalts technology that will make more durable the pavement in the highways and roads of the cities of Colombia investigates the Colombian Institute of the Petroleum ICP. The project that will have important incidence in the solution of one of the main problems in the roads of cities like Bogota, is only one of the 35 investigation programs and application of new technologies that with relationship to the sector of the hydrocarbons and its influence branches the ICP advances. The investigation looks for to elevate the current average of useful life of the pavements, with that it would be reached a standard that has the developed countries in this field

Potential of Waste Oyster Shells as a Novel Biofiller for Hot-Mix Asphalt

Directory of Open Access Journals (Sweden)

Nader Nciri

2018-03-01

Full Text Available This paper reports the use of waste oyster shells as a novel biofiller for hot-mix asphalt (HMA pavement applications. The effects of different fractions (e.g., 0, 5, 10, 15 wt % of oyster shell powder (OSP on the bitumen performance were investigated. The chemical properties of unfilled and OSP-filled asphalts were characterized by means of thin layer chromatography-ionization detection (TLC-FID, Fourier transform-infrared spectroscopy (FT-IR, X-ray diffraction (XRD, and scanning electron microscopy (SEM. Thermal characteristics were examined by thermogravimetric analysis (TGA and differential scanning calorimetry (DSC. Physical and rheological properties were assessed through penetration, softening point, ductility, and dynamic shear rheometer (DSR tests. Results showed that OSP addition increased the resins content, as well as the stiffness of blends. No obvious reactions have occurred between the filler and the asphalt. A higher dose of OSP altered the morphology of the binder, whereas lower and intermediate doses improved its thermal stability and enhanced its low-temperature, rutting, and fatigue performances with respect to the plain asphalt. Overall, the waste oyster shells could be used as filler substitute, not only to improve the quality of road pavements but also to reduce the cost of their construction and solve the waste disposal problems.

Design Method and Cost-Benefit Analysis of Hybrid Fiber Used in Asphalt Concrete

Directory of Open Access Journals (Sweden)

Haiwei Zhang

2016-01-01

Full Text Available Fiber, as an additive, can improve the performance of asphalt concrete and be widely studied, but only a few works have been done for hybrid fiber. This paper presents a new and convenient method to design hybrid fiber and verifies hybrid fiber’s superiority in asphalt pavement engineering. Firstly, this paper expounds the design method used as its applied example with the hybrid fiber composed of lignin, polyester, and polypropylene fibers. In this method, a direct shear device (DSD is used to measure the shear damage energy density (SDED of hybrid fiber modified asphalts, and range and variance statistical analysis are applied to determine the composition proportion of hybrid fiber. Then, the engineering property of hybrid fiber reinforced asphalt concrete (AC-13 is investigated. Finally, a cost-benefit model is developed to analyze the advantage of hybrid fiber compared to single fibers. The results show that the design method employed in this paper can offer a beneficial reference. A combination of 1.8% of lignin fiber and 2.4% of polyester fiber plus 3.0% polypropylene fiber presented the best reinforcement of the hybrid fiber. The cost-benefit model verifies that the hybrid fiber can bring about comprehensive pavement performance and good economy.

Tack coat optimization for HMA overlays : accelerated pavement test report.

Science.gov (United States)

2009-02-01

Interface bonding between hot-mix asphalt (HMA) overlays and Portland cement concrete (PCC) pavements is one : of the most significant factors affecting overlay service life. This study was performed to quantify the effects of HMA type, : tack coat t...

Laboratory Evaluation of Aging Behaviour of SBS Modified Asphalt

Directory of Open Access Journals (Sweden)

Jie Wang

2017-01-01

Full Text Available To study the effect of aging SBS modified asphalt on the performance of asphalt pavement, aging at various times and temperatures was conducted with thin film oven, and then tests were made about the penetration, softening point, ductility, viscosity, toughness, and fluorescence microscopy of modified asphalt with different aging levels. The results show that, with the increasing of aging time, the penetration and ductility of modified asphalt decrease while its softening point and viscosity increase, and the variation trend of the toughness and tenacity is related to the aging temperature; the aging dynamic model with viscosity as parameter can well characterize the aging process of modified asphalt; at microlevel, with the decreasing of SBS particle size, the uniformity of particle size is better. Analysis of macroscopic properties, microscopic characteristics, and significance shows that the SBS particle area ratio has a significant correlation with tenacity as the aging temperature changes. When the aging temperature is 163°C, the SBS particle area ratio still has a significant correlation with tenacity as the aging time changes.

Accelerated Performance Testing on the 2006 NCAT Pavement Test Track

Science.gov (United States)

2009-12-01

The original National Center for Asphalt Technology (NCAT) Pavement Test Track was built in 2000 in Opelika, Alabama where it has served as a state-of-the-art, full-scale, closed-loop accelerated loading facility. The construction, operation, and res...

Determination of Stone-Mastic Asphalt Concrete Durability

Science.gov (United States)

Yastremsky, D. A.; Abaidullina, T. N.; Chepur, P. V.

2018-05-01

The paper is focused on determination of durability of the stone-mastic asphalt (SMA) concrete, containing various stabilizing additives: "Armidon" (authors’ development) and "Viatop". At the first stage of experiments, the APA method was used to determine the rutting in the SMA containing these additives. Strength test for only top layers of asphalt concrete surface is insufficient for the calculation of the pavement fatigue resistance limits. Due to this fact, a comprehensive approach was employed which incorporates the interaction of the surface and subgrade natural soil. To analyze the road surface stress-strain state and to determine the durability margin, a numerical model was used (describes the processes of fatigue life). The model was developed basing on the finite element method (FEM) in the ANSYS program. Conducted studies and numerical calculations allowed obtaining the minimum and maximum stress values in the structure affected zones and in the zones of plastic deformations occurrence in artificial and natural bases. It allows predicting deformation processes during repeated wheel loads caused by moving vehicles. In course of studies, the results of static stresses in the pavement were also obtained.

Development of an asphalt aging procedure to assess long-term binder performance

KAUST Repository

Juristyarini, Pramitha

2011-09-07

Nine asphalts, including seven Strategic Highway Research Program asphalts and two Texas asphalts, were aged at several conditions of temperature and oxygen pressure to develop an aging test. Values for a dynamic shear rheometer function, a combination of both elastic and viscous properties that serves as an indicator of susceptibility to age-related pavement cracking, were measured for both aged and unaged samples. Each aging condition was ranked and calibrated against environmental room aging (60°C, 1 atm air), used to simulate road aging. PAV thin-film aging at 90°C, 20 atm air for 32 hr best represented environmental room aging. © Taylor & Francis Group, LLC.

Development of an asphalt aging procedure to assess long-term binder performance

KAUST Repository

Juristyarini, Pramitha; Davison, Richard R.; Glover, Charles J.

2011-01-01

Nine asphalts, including seven Strategic Highway Research Program asphalts and two Texas asphalts, were aged at several conditions of temperature and oxygen pressure to develop an aging test. Values for a dynamic shear rheometer function, a combination of both elastic and viscous properties that serves as an indicator of susceptibility to age-related pavement cracking, were measured for both aged and unaged samples. Each aging condition was ranked and calibrated against environmental room aging (60°C, 1 atm air), used to simulate road aging. PAV thin-film aging at 90°C, 20 atm air for 32 hr best represented environmental room aging. © Taylor & Francis Group, LLC.

Moisture Content Numerical Simulation on Structural Damage of Hot Mix Asphaltic Pavement

Science.gov (United States)

Abejide, O. S.; Mostafa, M. M. H.

2017-06-01

Considering the merits of road transportation in the economy and communication activities of the modern societies, it is imperative to design a safe, stable, efficient and cost effective road that will lead to increased economic development and growth of the South African nation. Although, the overarching effect of failed roads has in many ways led to increased travel time, loss of life and property; leading to reduced driver control on failed road sections (riding quality). Thus, time rate delamination of flexible pavement is a major focus of this study. Since structural collapse in a flexible pavement structure is caused by the evolution of different types of damage mechanisms; fatigue cracking, advanced crushing, temperature variation, and delamination. The effect of moisture content on HMA was analysed. The analysis from the multi-layered elastic model indicates that increase in moisture content in the underlying layer of HMA pavement results to increase in the strain of the individual layers and culminates to a decrease in the structural carrying capacity of the pavement with respect to number of load cycles that can be carried on the HMA pavement. This study shows a clear relationship between the moisture/saturation coefficient and the Elastic Modulus of the underlying geometric material layer properties of the pavement during the service life of the pavement.

Pavement system with rubber tire chips in subgrade

Energy Technology Data Exchange (ETDEWEB)

Ashtakala, B.; Hoque, A.K.M.M. [Concordia Univ., Montreal, PQ (Canada). Dept. of Civil Engineering

1995-12-31

A pavement design method was developed in which shredded rubber tire chips mixed with sand were used as a material for pavement subgrade. Rubber tire chips are highly compressible and produce both elastic and plastic deformations under the application of loads. Sand was added to fill the void between the tire chips and make the mixture a strong material. The design method considered the vertical compressive strain produced by the design life traffic load 18k (80 KN) repetitions. The equivalent thicknesses of the layers above the subgrade corresponding to this vertical compressive strain were determined using contour charts. From this equivalent thickness, the thicknesses for asphalt pavement, base, and sub-base were determined by Odemark`s method. 3 refs., 1 tab., 3 figs.

Evaluation of permanent deformation and durability of epoxidized natural rubber modified asphalt mix

Science.gov (United States)

Al-Mansob, Ramez A.; Ismail, Amiruddin; Rahmat, Riza Atiq O. K.; Nazri Borhan, Muhamad; Alsharef, Jamal M. A.; Albrka, Shaban Ismael; Rehan Karim, Mohamed

2017-09-01

The road distresses have caused too much in maintenance cost. However, better understandings of the behaviours and properties of asphalt, couples with greater development in technology, have allowed paving technologists to examine the benefits of introducing additives and modifiers. As a result, modifiers such as polymers are the most popular modifiers used to improve the performance of asphalt mix. This study was conducted to investigate the use of epoxidized natural rubber (ENR) to be mixed with asphalt mix. Tests were conducted to investigate the performance characteristics of ENR-asphalt mixes, where the mixes were prepared according to the wet process. Mechanical testing on the ENR-asphalt mixes have demonstrated that the asphalt mix permanent deformation performance at high temperature was found to be improved compared to the base mixes. However, the durability studies have indicated that ENR-asphalt mixes are slightly susceptible with the presence of moisture. The durability of the ENR-asphalt mixes were found to be enhanced in term of permanent deformation at high and intermediate temperatures compared to the base asphalt mixes. As conclusion, asphalt pavement performance can be enhanced by using ENR as modifier to face the major road distresses.

The impact of light-colored pavements on active layer dynamics revealed by Ground-Penetrating Radar monitoring

DEFF Research Database (Denmark)

Jørgensen, Anders Stuhr; Ingeman-Nielsen, Thomas

2008-01-01

further development of depressions in the asphalt pavement. One of these areas has been used in the GPR investigations to compare the variations of the frost table underneath a normal dark asphalt surface to that below a more reflective surface. The GPR results have shown a clear correlation between...... the use of the reflective surface and a reduced depth to frost table. In late summer the difference in the depths to the frost table is approximately 0.9 m. The results should promote the interest in the development and use of light colored pavement materials in order to reduce the effect of a warming...

Application of surplus and waste materials in roads pavement making

OpenAIRE

Mousavi, S. M.; Fazli, A. H.; Rouzmehr, F.

2011-01-01

Nowadays there are a lot of problems about surpluses and debris made by humans all around the world. Lots of these surpluses seriously harm our natural environment. Reuse of this kind of materials in other processes like building constructions or pavement help our natural environment in every aspect. Asphalt concrete is the main part of pavements in most parts of the world with an increasing rate of production in need of more ways and roads. In this paper we will provide...

Effect of tack coat on bonding characteristics at interface between asphalt concrete layers; Asphalt concrete no sokan fuchaku ni okeru tack concrete no koka

Energy Technology Data Exchange (ETDEWEB)

Hachiya, Y. [Port and Harbour Research Inst., Kanagawa (Japan); Umeno, S. [Ministry of Transport, Tokyo (Japan); Sato, K. [Nagaoka National College of Technology, Niigata (Japan)

1997-08-20

The effect of tack coat on bonding characteristics at the interface between surface and base layers was studied for airport asphalt pavement. In a fracture behavior, shear stress is first caused by horizontal loading at the interface between surface and base layers, resulting in peeling of the layers in the case of poor bonding. Further loading under the above condition results in fracture of asphalt concrete layers by bending or tensile actions. The bonding strength between layers decreases with an increase in interval of construction between surface and base layers, while the bonding strength between layers increases with sufficient curing of tack coat. Curing for 1 hour in the daytime and 6 hours or more in the nighttime is sufficient for evaporation of water content in asphalt emulsion. The use of conventional asphalt emulsion for the sandy interface as tack coat deduces the bonding strength in the case of poor curing. Asphalt emulsion containing high-penetration rubber can improve the bonding strength. 12 refs., 27 figs., 2 tabs.

Nature based solutions to mitigate soil sealing in urban areas: Results from a 4-year study comparing permeable, porous, and impermeable pavements.

Science.gov (United States)

Fini, A; Frangi, P; Mori, J; Donzelli, D; Ferrini, F

2017-07-01

Soil sealing is one of the most pervasive forms of soil degradation that follows urbanization and, despite innovative pavements (i.e. pervious) are being installed in urban areas to mitigate it, there is little research on the effects of pervious pavements on soil water and carbon cycle and on the physiology of urban trees. The aim of this 4-year experiment was to assess the effects of three pavements, differing in permeability to water and gases, on some soil physical parameters, and on growth and physiology of newly planted Celtis australis and Fraxinus ornus. Treatments were: 1) impermeable pavement (asphalt on concrete sub-base); 2) permeable pavement (pavers on crushed rock sub-base); 3) porous design (porous pavement on crushed rock sub-base); 4) control (unpaved soil, kept free of weed by chemical control). Soil (temperature, moisture, oxygen content and CO 2 efflux) and plant (above- and below-ground growth, leaf gas exchange, chlorophyll fluorescence, water relations) parameters were measured. All types of pavements altered the water cycle compared to unpaved soil plots, but this disturbance was less intense in porous pavements than in other soil cover types. Porous pavements allowed both higher infiltration and evaporation of water than both pavers and asphalt. Reduction of evaporative cooling from soil paved with permeable and impermeable pavements contributed to significant soil warming: at 20cm depth, soils under concrete pavers and asphalt were 4 and 5°C warmer than soil covered by porous pavements and unpaved soils, respectively. Thus, enhancing evaporation from paved soil by the use of porous pavements may contribute to mitigating urban heat islands. CO 2 greatly accumulated under impermeable and permeable pavements, but not under porous pavements, which showed CO 2 efflux rates similar to control. Soil oxygen slightly decreased only beneath asphalt. Growth of newly planted C. australis and F. ornus was little affected by pavement type. Tree

Volatilization of polycyclic aromatic hydrocarbons from coal-tar-sealed pavement.

Science.gov (United States)

Van Metre, Peter C; Majewski, Michael S; Mahler, Barbara J; Foreman, William T; Braun, Christopher L; Wilson, Jennifer T; Burbank, Teresa L

2012-06-01

Coal-tar-based pavement sealants, a major source of PAHs to urban water bodies, are a potential source of volatile PAHs to the atmosphere. An initial assessment of volatilization of PAHs from coal-tar-sealed pavement is presented here in which we measured summertime gas-phase PAH concentrations 0.03 m and 1.28 m above the pavement surface of seven sealed (six with coal-tar-based sealant and one with asphalt-based sealant) and three unsealed (two asphalt and one concrete) parking lots in central Texas. PAHs also were measured in parking lot dust. The geometric mean concentration of the sum of eight frequently detected PAHs (ΣPAH(8)) in the 0.03-m samples above sealed lots (1320 ng m(-3)) during the hottest part of the day was 20 times greater than that above unsealed lots (66.5 ng m(-3)). The geometric mean concentration in the 1.28-m samples above sealed lots (138 ng m(-3)) was five times greater than above unsealed lots (26.0 ng m(-3)). Estimated PAH flux from the sealed lots was 60 times greater than that from unsealed lots (geometric means of 88 and 1.4 μg m(-2) h(-1), respectively). Although the data set presented here is small, the much higher estimated fluxes from sealed pavement than from unsealed pavement indicate that coal-tar-based sealants are emitting PAHs to urban air at high rates compared to other paved surfaces. Published by Elsevier Ltd.

Influence of limestone fillers on combustion characteristics of asphalt mortar for pavements

DEFF Research Database (Denmark)

Ke, Wu; Kai, Zhu; Wu, Hao

2014-01-01

Asphalt materials will be ignited and release significant toxic fumes within tunnel fires. Thus, combustion characteristics of asphalt materials used in road tunnel should be studied in order to limit such an adverse effect. In the present work we study the influence of limestone fillers on combu...

Characteristics of dynamic triaxial testing of asphalt mixtures

Science.gov (United States)

Ulloa Calderon, Alvaro

Due to the increasing traffic loads and tire pressures, a serious detrimental impact has occurred on flexible pavements in the form of excessive permanent deformation once the critical combination of loading and environmental conditions are reached. This distress, also known as rutting, leads to an increase in road roughness and ultimately jeopardizes the road users' safety. The flow number (FN) simple performance test for asphalt mixtures was one of the final three tests selected for further evaluation from the twenty-four test/material properties initially examined under the NCHRP 9-19 project. Currently, no standard triaxial testing conditions in terms of the magnitude of the deviator and confining stresses have been specified. In addition, a repeated haversine axial compressive load pulse of 0.1 second and a rest period of 0.9 second are commonly used as part of the triaxial testing conditions. The overall objective of this research was to define the loading conditions that created by a moving truck load in the hot mixed asphalt (HMA) layer. The loading conditions were defined in terms of the triaxial stress levels and the corresponding loading time. Dynamic mechanistic analysis with circular stress distribution was used to closely simulate field loading conditions. Extensive mechanistic analyses of three different asphalt pavement structures subjected to moving traffic loads at various speeds and under braking and non-braking conditions were conducted using the 3D-Move model. Prediction equations for estimating the anticipated deviator and confining stresses along with the equivalent deviator stress pulse duration as a function of pavement temperature, vehicle speed, and asphalt mixture's stiffness have been developed. The magnitude of deviator stress, sigmad and confining stress, sigmac, were determined by converting the stress tensor computed in the HMA layer at 2" below pavement surface under a moving 18-wheel truck using the octahedral normal and shear

Quality control/quality assurance testing for joint density and segregation of asphalt mixtures.

Science.gov (United States)

2013-04-01

Longitudinal joint quality control/assurance is essential to the successful performance of asphalt pavements and it has received considerable amount of attention in recent years. The purpose of the study is to evaluate the level of compaction at the ...

Preliminary evaluation of the lifecycle costs and market barriers of reflective pavements; TOPICAL

International Nuclear Information System (INIS)

Ting, M.; Koomey, J.G.; Pomerantz, M.

2001-01-01

The objective of this study is to evaluate the life cycle costs and market barriers associated with using reflective paving materials in streets and parking lots as a way to reduce the urban heat island effect. We calculated and compared the life cycle costs of conventional asphalt concrete (AC) pavements to those of other existing pavement technologies with higher reflectivity-portland cement concrete (PCC), porous pavements, resin pavements, AC pavements using light-colored chip seals, and AC pavements using light-colored asphalt emulsion additives. We found that for streets and parking lots, PCC can provide a cost-effective alternative to conventional AC when severely damaged pavements must be completely reconstructed. We also found that rehabilitating damaged AC streets and intersections with thin overlays of PCC (ultra-thin white topping) can often provide a cost-effective alternative to standard rehabilitation techniques using conventional AC. Chip sealing is a common maintenance treatment for low-volume streets which, when applied using light-colored chips, could provide a reflective pavement surface. If the incremental cost of using light-colored chips is low, this chip sealing method could also be cost-effective, but the incremental costs of light-colored chips are as of yet uncertain and expected to vary. Porous pavements were found to have higher life cycle costs than conventional AC in parking lots, but several cost-saving features of porous pavements fell outside the boundaries of this study. Resin pavements were found to be only slightly more expensive than conventional AC, but the uncertainties in the cost and performance data were large. The use of light-colored additives in asphalt emulsion seal coats for parking lot pavements was found to be significantly more expensive than conventional AC, reflecting its current niche market of decorative applications. We also proposed two additional approaches to increasing the reflectivity of conventional AC

Experimental Investigations of Effect of Sulphur on Beach Sand–Fly Ash–Asphalt (S-F-A Paving Mixes

Directory of Open Access Journals (Sweden)

Satyakumar, M.

2013-01-01

Full Text Available The main components of the flexible pavements are asphalt and aggregates. But in most of the places in India there is shortage of the good quality aggregates (especially coarse aggregates, at the same time beach sand is available in plenty in many regions. Due to relative abundance of beach sand, the studies on the utilities of the beach sand in paving mixes are worth taking up. But beach Sand-Asphalt mix alone is not suitable for pavement construction, because of its low stability and high air voids. In the present study, Sand-Fly ash-Asphalt-Sulphur (S-F-A-S mixes are being made in different proportions and tested for their properties. Fatigue strength, stability, water sensitivity, stiffness modulus and dynamic modulus tests are carried out at standard test conditions and the results are analyzed for drawing conclusions. This study investigates the potential use of abundant ingredients, which may replace the ones which are scarce in nature.

Influence of Diatomite and Mineral Powder on Thermal Oxidative Ageing Properties of Asphalt

Directory of Open Access Journals (Sweden)

Yongchun Cheng

2015-01-01

Full Text Available Ageing of asphalt affects the performances of asphalt pavement significantly. Therefore, effects of diatomite and mineral powder on ageing properties of asphalt were investigated systematically in order to improve the antiageing property of mixture. Thin film oven test (TFOT was used to conduct the short term ageing in laboratory. Softening points, penetrations, force ductility, low temperature creep properties, and viscosities of asphalt mastics were tested before and after TFOT, respectively. Results indicated that percent retained penetration (PRP increased with the increasing of fillers. Increment of softening point (ΔT, ductility retention rate (DRR, deformation energy ageing index (JAI, and viscosity ageing index (VAI of asphalt mastics nonlinearly decreased with the increasing of fillers. Ageing of asphalt was reduced by diatomite and mineral powder. And the antiageing effect of diatomite was better than that of mineral powder as a result of its porous structure. It is suggested that the mineral powder could be reasonably replaced by diatomite in order to reduce thermal oxidative ageing of asphalt mixture. The optimal content of diatomite 12.8% is also suggested for engineering.

Harnessing Pavement Power : Developing Renewable Energy Technology in the Public Right-of-Way

Science.gov (United States)

2013-09-18

Intelligent Compaction (IC) of soil and asphalt mixes is an innovative approach that has been utilized to achieve uniform, adequate compaction of pavement layers during construction. Commercially available IC products provide machine specific compact...

Performance evaluation of stone matrix asphalt using indonesian natural rock asphalt as stabilizer

Directory of Open Access Journals (Sweden)

Nyoman Suaryana

2016-09-01

Full Text Available One type of road pavement material which is developed to be more resistant to permanent deformation is the SMA (Stone Matrix Asphalt. Utilization of the SMA mix in Indonesia has constraints in gain stabilizer and also difficulty to comply the gradations, mainly because it needs a relatively large amount of filler. Alternative of local materials that can be used is asbuton (natural rock asphalt from Buton Island. Asbuton is expected to act as a stabilizer and simultaneously provides an additional filler. The objective of this research is to evaluate the performance of the SMA that uses the asbuton. The methodology used in this research is the experimental method, its starts from material testing, design mix and performance testing that includes dynamic modulus, permanent deformation and fatigue resistance. The results obtained showed asbuton can prevent asphalt draindown as well as increase the proportion of filler. Draindown asphalt can be prevented by using binder absorbers with fiber cellulose and viscosity boosters with asbuton. Asbuton (LGA 50/25 can behave as a stabilizer as well as cellulose fiber. Addition of asbuton also improves the performance of the SMA mix, as shown with increase in the value of dynamic stability. In terms of resistance to fatigue, SMA with cellulosa as stabilizer and SMA with asbuton as stabilizer, relatively have the same performance. Master curve of dynamic modulus indicates SMA with asbuton as stabilizer is relatively stiffer at high temperatures (more than 4.4 °C, but relatively less stiff (less brittle at low temperatures. Keywords: Stone matrix asphalt, Asbuton, Draindown, Dynamic modulus, Permanent deformation

Production and performance of desulfurized rubber asphalt binder

Directory of Open Access Journals (Sweden)

Yanping Sheng

2017-05-01

Full Text Available Asphalt rubber binder typically exhibits disadvantages like segregation and high viscosity; however, this can be improved by the incorporation of desulfurized rubber powder. This study examined the swelling principle of desulfurized rubber asphalt (DRA. In addition, it evaluated the performance of DRA fabricated with various rubber powder contents under different shear conditions and development time. Superpave binders tests, including Brookfield viscosity, dynamic shear rheometer (DSR and bending beam rheometer (BBR tests, were applied on three control binders (i.e., neat, 20 mesh asphalt rubber binder, 40 mesh asphalt rubber binder and a DRA binder. Binder testing results indicated that rubber powder swelled into the base binder and resulted in enhanced stability. Optimum performance of the DRA binder was achieved by adding 20% (by weight of rubber powder into the base binder at shear rate, shear temperature, shear time and development time of 7000 r/min, 170 °C, 60 min and 45 min, respectively. Modified ranges of production conditions were also provided to widen the application of DRA in field construction. It appeared that DRA binder benefited from the recovered plasticity and viscosity of the rubber and consequently, exhibited superior performance over the neat and conventional asphalt rubber binders. Preliminary mixture evaluation was also conducted and the DRA binder was found to significantly improve the mixture resistance to permanent deformation and water damage. Overall, the DAR binder is encouraged to be used as a modified binder for flexible pavements. Keywords: Desulfurized rubber asphalt, Swelling model, Production process, Asphalt performance, Rubber asphalt

Operational properties of nanomodified stone mastic asphalt

Directory of Open Access Journals (Sweden)

Inozemtsev Sergey Sergeevich

2015-03-01

Full Text Available In order to prolong the lifetime and to improve the quality of pavements made of asphalt concrete it is necessary to apply innovative solutions in the process of design of such building materials. In order to solve the problem of low durability of asphalt concrete a modifier was proposed, which consists of diatomite, iron hydroxide sol (III and silica sol. Application of the diatomite with nanoscale layer of nanomodifier allows getting a stone mastic asphalt, which has high values of physical and mechanical properties and allows refusing from expensive stabilizing additive. Mineral filler was replaced by diatomite, which has been modified by iron hydroxide sol (III and silica sol. Modified diatomite allows sorption of bitumen and increase the cohesive strength and resistance to shear at positive temperatures. The modified asphalt has higher resistance to rutting at high temperature, abrasion resistance at low temperature and impact of climatic factors: alternate freezing and thawing, wetting-drying, UV and IR radiations. It is achieved by formation of solid and dense bitumen film at the phase interface and controlling the content of light fractions of the bitumen. The modifier consists of sol of iron hydroxide, which blocks the oxidation and polymerization of bitumen during operation. The proposed material allows controlling the initial structure formation of stone mastic asphalt. It was shown that modern test methods allow assessing the durability of asphalt in the design phase compositions.

Characteristic Asphalt Concrete Wearing Course (ACWC) Using Variation Lime Filler

Science.gov (United States)

Permana, R. A.; Pramesti, F. P.; Setyawan, A.

2018-03-01

This research use of lime filler Sukaraja expected add durability layers of concrete pavement is asphalt damage caused by the weather and load traffic. This study attempts to know how much value characteristic Marshall on a mixture of concrete asphalt using lime filler. This research uses experimental methods that is with a pilot to get results, thus will look filler utilization lime on construction concrete asphalt variation in filler levels 2 %, 3 %, 4 %.The results showed that the use of lime filler will affect characteristic a mixture of concrete asphalt. The more filler chalk used to increase the value of stability. On the cretaceous filler 2 % value of stability is 1067,04 kg. When lime filler levels added to the levels of filler 4 %, the value of stability increased to 1213,92 kg. The flexibility increased the number of filler as levels lime 2 % to 4 % suggests that are conducted more stiff mix.

Dynamic Properties and Fatigue Life of Stone Mastic Asphalt Mixtures Reinforced with Waste Tyre Rubber

Directory of Open Access Journals (Sweden)

Nuha Salim Mashaan

2013-01-01

Full Text Available Today, virgin polymer modified asphalt mixes are comparatively more expensive for road pavement. One way to reduce the expense of such construction and to make it more convenient is the application of inexpensive polymer, such as waste polymer. The primary aim of this study was to investigate the effect of adding waste tyre rubber (crumb rubber modifier (CRM on the stiffness and fatigue properties of stone mastic asphalt (SMA mixtures. Various percentages of waste CRM with size of 0.60 mm were added to SMA mixtures. Indirect tensile stiffness modulus test was conducted at temperatures of 5, 25, and 40°C. Indirect tensile fatigue test was conducted at three different stress levels (2000, 2500, and 3000 N. The results show that the stiffness modulus of reinforced SMA samples containing various contents of CRM is significantly high in comparison with that of nonreinforced samples, and the stiffness modulus of reinforced samples is in fact less severely affected by the increased temperature compared to the nonreinforced samples. Further, the results show that CRM reinforced SMA mixtures exhibit significantly higher fatigue lives compared to the nonreinforced mixtures help in and promotion of sustainable technology by recycling of waste materials in much economical and environmental-friendly manner.

Aggregate surface areas quantified through laser measurements for South African asphalt mixtures

CSIR Research Space (South Africa)

Anochie-Boateng, Joseph

2012-02-01

Full Text Available design. This paper introduces the use of a three-dimensional (3D) laser scanning method to directly measure the surface area of aggregates used in road pavements in South Africa. As an application of the laser-based measurements, the asphalt film...

Pavement service life extension due to asphalt surface treatment interlayer : research project capsule.

Science.gov (United States)

2016-07-01

The Louisiana Department of Transportation and Development (DOTD) has been : using asphalt surface treatment (AST) interlayers over soil cement base courses : as a means to mitigate shrinkage cracks from reflecting through the asphaltic : concrete (A...

Analysis, testing and verification of the behavior of composite pavements under Florida conditions using a heavy vehicle simulator

Science.gov (United States)

Tapia Gutierrez, Patricio Enrique

Whitetopping (WT) is a rehabilitation method to resurface deteriorated asphalt pavements. While some of these composite pavements have performed very well carrying heavy load, other have shown poor performance with early cracking. With the objective of analyzing the applicability of WT pavements under Florida conditions, a total of nine full-scale WT test sections were constructed and tested using a Heavy Vehicle Simulator (HVS) in the APT facility at the FDOT Material Research Park. The test sections were instrumented to monitor both strain and temperature. A 3-D finite element model was developed to analyze the WT test sections. The model was calibrated and verified using measured FWD deflections and HVS load-induced strains from the test sections. The model was then used to evaluate the potential performance of these test sections under critical temperature-load condition in Florida. Six of the WT pavement test sections had a bonded concrete-asphalt interface by milling, cleaning and spraying with water the asphalt surface. This method produced excellent bonding at the interface, with shear strength of 195 to 220 psi. Three of the test sections were intended to have an unbonded concrete-asphalt interface by applying a debonding agent in the asphalt surface. However, shear strengths between 119 and 135 psi and a careful analysis of the strain and the temperature data indicated a partial bond condition. The computer model was able to satisfactorily model the behavior of the composite pavement by mainly considering material properties from standard laboratory tests and calibrating the spring elements used to model the interface. Reasonable matches between the measured and the calculated strains were achieved when a temperature-dependent AC elastic modulus was included in the analytical model. The expected numbers of repetitions of the 24-kip single axle loads at critical thermal condition were computed for the nine test sections based on maximum tensile stresses

The Effect of SBS Polymer on the Dynamic Properties of Asphalt

Directory of Open Access Journals (Sweden)

H. Ziari

2008-12-01

Full Text Available Polymer application for the improvement and modification of the bitumen used in roads surfaces has expanded in recent decades. The roads engineers and constructors, therefore, have used the modified bitumen in asphalts helping in this way to increase roads and pavements service life and improving the durability of the roads and asphalts. The bitumen used in asphalt mixture constitutes only a low percentage of the weight of this mixture (between 4% and 6%, but even this small amount has a significant effect on asphalt performance. The polymers that are mostly used in promoting the bitumen specifications are polymer modifiers including: styrenebutadiene- styrene (SBS, as well as similar polymers such as styrene-butadiene-rubber (SBR, ethylene-vinylacetate (EVA and polyethylene (PE. Polymers as the most important family of bitumen modifiers are added to bitumen to improve bitumen performance and to increase its effectiveness. Among the existing polymers, SBS is considered as the best bitumen modifier. In this research, SBS as one of the elastomer-thermoplast modifiers was added in different weights (2%-5% to bitumen 60/70 in Isfahan Refinery and its effect on asphalt properties were investigated. Adding this polymer to bitumen improves the Marshall stability of sample asphalt, flow, module of rupture and asphalt content voids. However, it has a minor effect on asphalt special weight. Adding SBS would also lead to asphalt fatigue life.

Nontraditional Fog Seal for Asphalt Pavement : Performance on Shoulder Sections in Minnesota

Science.gov (United States)

2018-05-01

The pavement engineering community has recently been introduced to a number of nontraditional products intended for uses as surface sealers for bituminous pavements. Many new products use agricultural-based components and little is known regarding th...

Studying the Physical Properties of Hma with Recycled Aggregate Subjected to Moisture

Directory of Open Access Journals (Sweden)

Ahlam K. Razzaq

2018-01-01

Full Text Available As being exposed to water that exists on asphalt road, HMA that is created by utilizing a certain resources may require to be made strong due to the capability of that water to stop the covering to be attached to the aggregate, consequently, asphalt road layers will not be held jointly, this will have a negative influence on the asphalt that will be damaged quickly. Such phenomenon is known as "the erosion", which requires to be dealt with by, for example, improving asphalt layers by means of specific resources that assist in existence of water. Different ways in this work are employed to calculate the strength of various mixes via using used aggregate that is exposed to  saturation times, similarly, the importance of exploiting the anti-stripping as chemical addition is determined. Three kinds of HMA were exposed in the current study, 60% of the first kind were made of used aggregate taking from crushed pavement, and 60% of the second kind were taking from using aggregate that is part of concrete mix, while the third mixture has 10% of wax used as an addition by pavement weight. These mixtures were soaked in water bath of 25o C for various intervals of time that are (3, 7, 15, 28 days. Many investigations examinations had been as well executed, and then the outcomes were contrasted against standard pavement blend subjected to similar circumstances. Number of examinations were adopted in this study, these are (Marshall Stability and flow, mass thickness, roundabout elasticity, compressive quality, affectability to temperature, flexible modulus. The study achieved a good success as it makes important outcomes, the enhanced pavement showed strength against moisture damage while taking advantage of used aggregate of preceding blends, on other hand, the wax has affective role in raising these strengths in addition to develop the characteristics of HMA. 

Use of warm mix asphalt pavement on Interstate 95, Carmel to Hampden, northbound.

Science.gov (United States)

2012-06-01

A number of new technologies have been developed to lower the production and placement temperatures : of hot-mix asphalt (HMA). Generically, these technologies are referred to as warm-mix asphalt (WMA). : In Europe and to a lesser extent in North Ame...

Determining Surface Infiltration Rate of Permeable Pavements with Digital Imaging

Directory of Open Access Journals (Sweden)

Caterina Valeo

2018-01-01

Full Text Available Cell phone images of pervious pavement surfaces were used to explore relationships between surface infiltration rates (SIR measured using the ASTM C1701 standard test and using a simple falling head test. A fiber-reinforced porous asphalt surface and a highly permeable material comprised of stone, rubber and a polymer binder (Porous Pave were tested. Images taken with a high-resolution cellphone camera were acquired as JPEG files and converted to gray scale images in Matlab® for analysis. The distribution of gray levels was compared to the surface infiltration rates obtained for both pavements with attention given to the mean of the distribution. Investigation into the relationships between mean SIR and parameters determined from the gray level distribution produced in the image analysis revealed that mean SIR measured in both pavements were proportional to the inverse of the mean of the distribution. The relationships produced a coefficient of determination over 85% using both the ASTM and the falling head test in the porous asphalt surface. SIR measurements determined with the ASTM method were highly correlated with the inverse mean of the distribution of gray levels in the Porous Pave material as well, producing coefficients of determination of over 90% and Kendall’s tau-b of roughly 70% for nonparametric data.

Design and Properties of Asphalt Concrete Mixtures Using Renewable Bioasphalt Binder

Science.gov (United States)

Setyawan, A.; Djumari; Irfansyah, P. A.; Shidiq, A. M.; Wibisono, I. S.; Fauzy, M. N.; Hadi, F. N.

2017-02-01

The needs of petroleum asphalt as materials for pavement is very large, while the petroleum classified as natural resources that cannot be renewable. As a result of petroleum dwindling and prices tend to be more expensive. So that requiring other alternative materials as a substitute for conventional asphalt derived from biomass or often called bioasphalt. This study aims to know the volumetric and Marshall characteristics on Asphalt Cement ( AC ) using the Damar asphalt modification to substitute 60/70 penetration asphalt as a binder. The volumetric and Marshall characteristic are porosity, density, flow, stability, and Marshall quotient. The characteristic of asphalt concrete at optimum bitumen content are compared to the conditions from highway agency 1987 and the general specification of asphalt concrete Bina Marga 2010 the third revision. The research uses experimental method in the laboratory with the samples made using the dasphalt modification as binder and incorporating the aggregate gradation no. VII SNI 03-1737-1989. The research is using 15 samples divided into 5 contents of damar asphalt, they are 5%, 5,5%, 6%, 6,5%, dan 7%. Tests carried out using Marshall test equipment to get the value of flow and stability and then be searched the value of optimum damar asphalt content. The result of asphalt concrete analysis using dasphalt modification as binder gives the value of optimum dasphalt content at 5,242%. The most characteristics already met the requirements and specifications.

Life Cycle Assessment on Cement Treated Recycling Base (CTRB Construction

Directory of Open Access Journals (Sweden)

Sudarno Sudarno

2014-08-01

Full Text Available LCA is one of the few environmental management techniques that are used to perform a risk assessment, environmental performance evaluation, environmental auditing, and environmental impact assessment and must be applied to the construction CTRB. The purpose of this study was to determine the amount of energy consumption is used and determine the amount of emissions (CO2 in the implementation of the Foundation Layer Top (base course with the former asphalt pavement aggregate blended cement / Recycling Cement Treated Base (CTRB. This study uses: (i Compilation and data inventory of relevant inputs and outputs of a product system; (ii Evaluating the potential environmental impacts associated with the data input and output; (iii Interpret the results of the inventory analysis and impact assessment in relation to the research objectives. The results showed that Energy consumption in the implementation of recycling pavement (CTRB is 225.46 MJ / km of roads and the resulting GHG emissions 17,43Ton CO2 / km of roads. Previous researchers to calculate the energy consumption of road works on the implementation of conventional (hotmix is 383.46 MJ / km of roads and the resulting GHG emissions 28.24 Ton CO2 / km of roads. If the calculated difference between a job and Hotmix CTRB and then a comparison is made CTRB energy consumption is 158 MJ / km of road, this happens 70.07% savings and GHG emissions resulting difference is 10.81 tons of CO2 / km of road, resulting in a decrease in 62,02%.

Research on Fiber Micro-Surfacing Mixture Design and Pavement Performance in Interchange’s Connections

Directory of Open Access Journals (Sweden)

Wu Zhaoyang

2015-01-01

Full Text Available In order to use the micro-surfacing which is the existing micro-surfacing technology guide that has some technical defects, the method to determine the optimal dosage of emulsified asphalt and best whetstone is not very reasonable, and it impedes the application and development of micro-surfacing technology to improve the performance of the pavement. In this paper, the “graphical method” is first used to determine the optimal dosage range of emulsified asphalt. Nowadays, a large number of expressways reach the stage of repair and maintenance. Interchange ramp exit and entrance are always the accident-prone sections and, it’s easy to over-look the pavement’s skid resistance of those areas. Micro-surfacing can significantly improve the performance of pavement, especially the skid resistance. Verified with laboratory tests, it recommends that the dosage of emulsified asphalt corresponding to the peak of flexural strain measured with low temperature bending test as OAC of micro-surfacing mixture shows technical superiority. The use of fiber micro-surfacing at the ramp’s exit and entrance can reduce the braking distance.

Experimental Evaluation of Anti-Stripping Additives Mixing in Road Surface Pavement Materials

OpenAIRE

Tienfuan Kerh; Yu-Min Wang; Yulern Lin

2005-01-01

Most road surfaces in Taiwan are paved with asphalt concrete but the phenomena of rutting, cracking and stripping of the pavement are frequently occurring due to the effects of traffic flow, thermal variation and water erosion caused by rain. In this study, a series of experiments were performed to examine the effectiveness of anti-stripping fillers, which include; rock flour, rock flour with 1% lime and rock flour with 1% cement, respectively, in the mixture of asphalt concrete. The experime...

Performance characterizations of asphalt binders and mixtures incorporating silane additive ZycoTherm

Science.gov (United States)

Hasan, Mohd Rosli Mohd; Hamzah, Meor Othman; Yee, Teh Sek

2017-10-01

Experimental works were conducted to evaluate the properties of asphalt binders and mixtures produced using a relatively new silane additive, named ZycoTherm. In this study, 0.1wt% ZycoTherm was blended with asphalt binder to enable production of asphalt mixture at lower than normal temperatures, as well as improve mix workability and compactability. Asphalt mixture performances towards pavement distresses in tropical climate region were also investigated. The properties of control asphalt binders (60/70 and 80/10 penetration grade) and asphalt binders incorporating 0.1% ZycoTherm were reported based on the penetration, softening point, rotational viscosity, complex modulus and phase angle. Subsequently, to compare the performance of asphalt mixture incorporating ZycoTherm with the control asphalt mixture, cylindrical samples were prepared at recommended temperatures and air voids depending on the binder types and test requirements. The samples were tested for indirect tensile strength (ITS), resilient modulus, dynamic creep, Hamburg wheel tracking and moisture induced damage. From compaction data using the Servopak gyratory compactor, specimen prepared using ZycoTherm exhibit higher workability and compactability compared to the conventional mixture. From the mixture performance test results, mixtures prepared with ZycoTherm showed comparable if not better performance than the control sample in terms of the resistance to moisture damage, permanent deformation and cracking.

Hybrid green permeable pave with hexagonal modular pavement systems

International Nuclear Information System (INIS)

Rashid, M A; Abustan, I; Hamzah, M O

2013-01-01

Modular permeable pavements are alternatives to the traditional impervious asphalt and concrete pavements. Pervious pore spaces in the surface allow for water to infiltrate into the pavement during rainfall events. As of their ability to allow water to quickly infiltrate through the surface, modular permeable pavements allow for reductions in runoff quantity and peak runoff rates. Even in areas where the underlying soil is not ideal for modular permeable pavements, the installation of under drains has still been shown to reflect these reductions. Modular permeable pavements have been regarded as an effective tool in helping with stormwater control. It also affects the water quality of stormwater runoff. Places using modular permeable pavement has been shown to cause a significant decrease in several heavy metal concentrations as well as suspended solids. Removal rates are dependent upon the material used for the pavers and sub-base material, as well as the surface void space. Most heavy metals are captured in the top layers of the void space fill media. Permeable pavements are now considered an effective BMP for reducing stormwater runoff volume and peak flow. This study examines the extent to which such combined pavement systems are capable of handling load from the vehicles. Experimental investigation were undertaken to quantify the compressive characteristics of the modular. Results shows impressive results of achieving high safety factor for daily life vehicles.