Gasification: An alternative solution for energy recovery and utilization of vegetable market waste.

Science.gov (United States)

Narnaware, Sunil L; Srivastava, Nsl; Vahora, Samir

2017-03-01

Vegetables waste is generally utilized through a bioconversion process or disposed of at municipal landfills, dumping sites or dumped on open land, emitting a foul odor and causing health hazards. The presents study deals with an alternative way to utilize solid vegetable waste through a thermochemical route such as briquetting and gasification for its energy recovery and subsequent power generation. Briquettes of 50 mm diameter were produced from four different types of vegetable waste. The bulk density of briquettes produced was increased 10 to 15 times higher than the density of the dried vegetable waste in loose form. The lower heating value (LHV) of the briquettes ranged from 10.26 MJ kg -1 to 16.60 MJ kg -1 depending on the type of vegetable waste. The gasification of the briquettes was carried out in an open core downdraft gasifier, which resulted in syngas with a calorific value of 4.71 MJ Nm -3 at the gasification temperature between 889°C and 1011°C. A spark ignition, internal combustion engine was run on syngas and could generate a maximum load up to 10 kW e . The cold gas efficiency and the hot gas efficiency of the gasifier were measured at 74.11% and 79.87%, respectively. Energy recovery from the organic vegetable waste was possible through a thermochemical conversion route such as briquetting and subsequent gasification and recovery of the fuel for small-scale power generation.

The impact of cost recovery on electric utilities' Clean Air Act compliance strategies

International Nuclear Information System (INIS)

Bensinger, D.L.

1993-01-01

By 1995, over 200 electric power plant units in twenty one states must comply with Phase I of the acid rain requirements in Title IV of the 1990 Clean Air Act Amendments (CAAA). By the year 2000, an additional 2200 units must comply with the Title IV. Compliance costs are expected to necessitate significant electricity rate increases. In order to recover their compliance costs, utilities must file rate increase requests with state public utility commissions (PUC's), and undergo a rate proceeding involving public heatings. Because of the magnitude of cost and the complexity of compliance options, including interaction with Titles I and III of the CAAA, extensive PUC reviews of compliance strategies are likely. These reviews could become as adversarial as the nuclear prudence reviews of the 1980's. A lack of understanding of air pollution and the CAA by much of the general public and the flexibility of compliance options creates an environment conducive to adverse public reaction to the cost of complying with the Clean Air Act. Public attitudes toward pollution control technologies will be greatly affected by these hearings, and the early plant hearings will shape the utility rate making process under the Clean Air Act. Inadequate cost recovery due to constrained compliance strategies or adverse hearings could significantly inhibit industry willingness to invest in certain control technologies or advanced combustion technologies. There are already signs that Clean Air Act compliance will be the prudence issue of the 1990's for utilities, even where state statutes mandate particular compliance approaches. Specific actions should be undertaken now by the utility industry to improve the probability of sound cost recovery decisions, preserve compliance options, including multimedia strategies, and avoid the social- and cost-acceptance problems of nuclear power

Recovery from Psychosis: A Phenomenological Inquiry

Science.gov (United States)

Nixon, Gary; Hagen, Brad; Peters, Tracey

2010-01-01

While mainstream psychiatry tends to view psychosis as an enduring and chronic condition, there is growing interest in the possibility of recovery from psychosis. A phenomenological research method was utilized in interviewing 17 individuals who all self-identified as being in recovery from psychosis. The research question was, "What was the lived…

Method selection for sustainability assessments: The case of recovery of resources from waste water.

Science.gov (United States)

Zijp, M C; Waaijers-van der Loop, S L; Heijungs, R; Broeren, M L M; Peeters, R; Van Nieuwenhuijzen, A; Shen, L; Heugens, E H W; Posthuma, L

2017-07-15

Sustainability assessments provide scientific support in decision procedures towards sustainable solutions. However, in order to contribute in identifying and choosing sustainable solutions, the sustainability assessment has to fit the decision context. Two complicating factors exist. First, different stakeholders tend to have different views on what a sustainability assessment should encompass. Second, a plethora of sustainability assessment methods exist, due to the multi-dimensional characteristic of the concept. Different methods provide other representations of sustainability. Based on a literature review, we present a protocol to facilitate method selection together with stakeholders. The protocol guides the exploration of i) the decision context, ii) the different views of stakeholders and iii) the selection of pertinent assessment methods. In addition, we present an online tool for method selection. This tool identifies assessment methods that meet the specifications obtained with the protocol, and currently contains characteristics of 30 sustainability assessment methods. The utility of the protocol and the tool are tested in a case study on the recovery of resources from domestic waste water. In several iterations, a combination of methods was selected, followed by execution of the selected sustainability assessment methods. The assessment results can be used in the first phase of the decision procedure that leads to a strategic choice for sustainable resource recovery from waste water in the Netherlands. Copyright © 2017 Elsevier Ltd. All rights reserved.

Utilizing Geographic Information Systems (GIS) to analyze geographic and demographic patterns related to forensic case recovery locations in Florida.

Science.gov (United States)

Kolpan, Katharine E; Warren, Michael

2017-12-01

This paper highlights how Geographic Information Systems (GIS) can be utilized to analyze biases and patterns related to physical and cultural geography in Florida. Using case recovery locations from the C. Addison Pound Human Identification Laboratory (CAPHIL), results indicate that the majority of CAPHIL cases are recovered from urban areas with medium to low population density and low rates of crime. The results also suggest that more accurate record keeping methods would enhance the data. Copyright © 2017 Elsevier B.V. All rights reserved.

Microbiological methods for the water recovery systems test, revision 1.1

Science.gov (United States)

Rhoads, Tim; Kilgore, M. V., Jr.; Mikell, A. T., Jr.

1990-01-01

Current microbiological parameters specified to verify microbiological quality of Space Station Freedom water quality include the enumeration of total bacteria, anaerobes, aerobes, yeasts and molds, enteric bacteria, gram positives, gram negatives, and E. coli. In addition, other parameters have been identified as necessary to support the Water Recovery Test activities to be conducted at the NASA/MSFC later this year. These other parameters include aerotolerant eutrophic mesophiles, legionellae, and an additional method for heterotrophic bacteria. If inter-laboratory data are to be compared to evaluate quality, analytical methods must be eliminated as a variable. Therefore, each participating laboratory must utilize the same analytical methods and procedures. Without this standardization, data can be neither compared nor validated between laboratories. Multiple laboratory participation represents a conservative approach to insure quality and completeness of data. Invariably, sample loss will occur in transport and analyses. Natural variance is a reality on any test of this magnitude and is further enhanced because biological entities, capable of growth and death, are specific parameters of interest. The large variation due to the participation of human test subjects has been noted with previous testing. The resultant data might be dismissed as 'out of control' unless intra-laboratory control is included as part of the method or if participating laboratories are not available for verification. The purpose of this document is to provide standardized laboratory procedures for the enumeration of certain microorganisms in water and wastewater specific to the water recovery systems test. The document consists of ten separate cultural methods and one direct count procedure. It is not intended nor is it implied to be a complete microbiological methods manual.

Effectiveness evaluation of whole-body electromyostimulation as a post-exercise recovery method.

Science.gov (United States)

DE LA Camara, Miguel A; Pardos, Ana I; Veiga, Óscar L

2018-01-04

Whole-body electromyostimulation (WB-EMS) devices are now being used in health and sports training, although there are few studies investigating their benefits. The objective of this research was to evaluate the effectiveness of WB-EMS as a post-exercise recovery method, and compare it with other methods like active and passive recovery. The study included nine trained men (age = 21 ± 1years, height = 1.77 ± 0.4 m, mass = 62 ± 7 kg). Three trials were performed in three different sessions, 1 week apart. Each trial, the participants completed the same exercise protocol and a different recovery method each time. A repeated measures design was used to check the basal reestablishing on several physiological variables [lactate, heart rate, percentage of tissue hemoglobin saturation, temperature, and neuromuscular fatigue] and to evaluate the quality of recovery. The non-parametric Wilcoxon and Friedman ANOVA tests were used to examine the differences between recovery methods. The results showed no differences between methods in the physiological and psychological variables analyzed. Although, the blood lactate concentration showed borderline statistical significance between methods (P = 0.050). Likewise, WB-EMS failed to recover baseline blood lactate concentration (P = 0.021) and percentage of tissue hemoglobin saturation (P = 0.023), in contrast to the other two methods. These findings suggest that WB-EMS is not a good recovery method because the power of reestablishing of several physiological and psychological parameters is not superior to other recovery methods like active and passive recovery.

Evaluating the utility and seasonality of NDVI values for assessing post-disturbance recovery in a subalpine forest.

Science.gov (United States)

Buma, Brian

2012-06-01

Forest disturbances around the world have the potential to alter forest type and cover, with impacts on diversity, carbon storage, and landscape composition. These disturbances, especially fire, are common and often large, making ground investigation of forest recovery difficult. Remote sensing offers a means to monitor forest recovery in real time, over the entire landscape. Typically, recovery monitoring via remote sensing consists of measuring vegetation indices (e.g., NDVI) or index-derived metrics, with the assumption that recovery in NDVI (for example) is a meaningful measure of ecosystem recovery. This study tests that assumption using MODIS 16-day imagery from 2000 to 2010 in the area of the Colorado's Routt National Forest Hinman burn (2002) and seedling density counts taken in the same area. Results indicate that NDVI is rarely correlated with forest recovery, and is dominated by annual and perennial forb cover, although topography complicates analysis. Utility of NDVI as a means to delineate areas of recovery or non-recovery are in doubt, as bootstrapped analysis indicates distinguishing power only slightly better than random. NDVI in revegetation analyses should carefully consider the ecology and seasonal patterns of the system in question.

Recovery and utilization of valuable metals from spent nuclear fuel. 3: Mutual separation of valuable metals

International Nuclear Information System (INIS)

Kirishima, K.; Shibayama, H.; Nakahira, H.; Shimauchi, H.; Myochin, M.; Wada, Y.; Kawase, K.; Kishimoto, Y.

1993-01-01

In the project ''Recovery and Utilization of Valuable Metals from Spent Fuel,'' mutual separation process of valuable metals recovered from spent fuel has been studied by using the simulated solution contained Pb, Ru, Rh, Pd and Mo. Pd was separated successfully by DHS (di-hexyl sulfide) solvent extraction method, while Pb was recovered selectively from the raffinate by neutralization precipitation of other elements. On the other hand, Rh was roughly separated by washing the precipitate with alkaline solution, so that Rh was refined by chelate resin CS-346. Outline of the mutual separation process flow sheet has been established of the combination of these techniques. The experimental results and the process flow sheet of mutual separation of valuable metals are presented in this paper

Characteristic of wet method of phosphorus recovery from polish sewage sludge ash with nitric acid

Directory of Open Access Journals (Sweden)

Gorazda Katarzyna

2016-01-01

Full Text Available Sewage Sludge Ash (SSA is a concentrated source of phosphorus and can be successfully recycled via a number of different routes. This paper presents research results on phosphorus recovery from differently combusted sewage sludge with the use of nitric acid extraction. Different SSA forms from Polish thermal utilization stations were compared. It was revealed that sewage treatment technology as well as combustion technology influence many physical and chemical parameters of ashes that are crucial for further phosphorus recovery from such waste according to the proposed method. Presented research defines extraction efficiency, characterized extracts composition and verifies the possibility of using SSA as cheaper and alternative sources of phosphorus compounds. Gdynia, Kielce and Kraków SSA have the best properties for the proposed technology of phosphorus recovery with high extraction efficiency greater than 86%. Unsuitable results were obtained for Bydgoszcz, Szczecin Slag and Warszawa SSA. Extraction process for Łódź and Szczecin Dust SSA need to be improved for a higher phosphorus extraction efficiency greater than 80%.

Spray method for recovery of heat-injured Salmonella Typhimurium and Listeria monocytogenes.

Science.gov (United States)

Back, Kyeong-Hwan; Kim, Sang-Oh; Park, Ki-Hwan; Chung, Myung-Sub; Kang, Dong-Hyun

2012-10-01

Selective agar is inadequate for supporting recovery of injured cells. During risk assessment of certain foods, both injured and noninjured cells must be enumerated. In this study, a new method (agar spray method) for recovering sublethally heat-injured microorganisms was developed and used for recovery of heat-injured Salmonella Typhimurium and Listeria monocytogenes. Molten selective agar was applied as an overlay to presolidified nonselective tryptic soy agar (TSA) by spray application. Heat-injured cells (55°C for 10 min in 0.1% peptone water or 55°C for 15 min in sterilized skim milk) were inoculated directly onto solidified TSA. After a 2-h incubation period for cell repair, selective agar was applied to the TSA surface with a sprayer, and the plates were incubated. The recovery rate for heat-injured Salmonella Typhimurium and L. monocytogenes with the spray method was compared with the corresponding rates associated with TSA alone, selective media alone, and the conventional overlay method (selective agar poured on top of resuscitated cells grown on TSA and incubated for 2 h). No significant differences (P > 0.05) were found in pathogen recovery obtained with TSA, the overlay method, and the spray method. However, a lower recovery rate (P recovery and detection of injured cells.

40 CFR Appendix C to Subpart F of... - Method for Testing Recovery Devices for Use With Small Appliances

Science.gov (United States)

2010-07-01

... for Use With Small Appliances C Appendix C to Subpart F of Part 82 Protection of Environment... Recovery Devices for Use With Small Appliances Recovery Efficiency Test Procedure for Refrigerant Recovery Equipment Used on Small Appliances The following test procedure is utilized to evaluate the efficiency of...

Defense by-products production and utilization program: noble metal recovery screening experiments

International Nuclear Information System (INIS)

Hazelton, R.F.; Jensen, G.A.; Raney, P.J.

1986-03-01

Isotopes of the platinum metals (rutheium, rhodium, and palladium) are produced during uranium fuel fission in nuclear reactors. The strategic values of these noble metals warrant considering their recovery from spent fuel should the spent fuel be processed after reactor discharge. A program to evaluate methods for ruthenium, rhodium, and palladium recovery from spent fuel reprocessing liquids was conducted at Pacific Northwest Laboratory (PNL). The purpose of the work reported in this docuent was to evaluate several recovery processes revealed in the patent and technical literature. Beaker-scale screening tests were initiated for three potential recovery processes: precipitation during sugar denitration of nitric acid reprocessing solutions after plutonium-uranium solvent extraction, adsorption using nobe metal selective chelates on active carbon, and reduction forming solid noble metal deposits on an amine-borane reductive resin. Simulated reprocessing plant solutions representing typical nitric acid liquids from defense (PUREX) or commercial fuel reprocessing facilities were formulated and used for evaluation of the three processes. 9 refs., 3 figs., 9 tabs

Economic analysis vs. capital-recovery requirements of power reactor decommissioning

International Nuclear Information System (INIS)

Ferguson, J.S.

1980-01-01

As a consultant to electric utilities the author often becomes involved in the development of policy for capital recovery and in the determination of depreciation rates that will implement the policy. Utility capital recovery is controlled by generally accepted depreciation accounting practices and by regulatory commission accounting rules and, as a result, can differ significantly from engineering economics. Those involved with decommissioning of power reactors should be aware of the depreciation accounting and regulatory framework that dictates capital recovery requirements, whether their involvement is related to engineering economics or capital recovery. This presentation defines that framework, points out several significant implications (particularly tax), describes several conforming capital-recovery methods, describes several techniques that have been used with the decommissioning component in economic analysis of alternative energy sources, and discusses why those involved in economic analysis should learn the accounting and regulatory framework for capital recovery

Feasibility study on recovery and utilization of coal mine gas (CMG) at Donetsk Coal Field

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of getting petroleum substitution energy and reducing greenhouse effect gas emission, an investigational study was carried out of the project for methane gas recovery/utilization at the Donbassa coal mine in Ukraine. At the Donbassa coal mine, degassing by test boring is being conducted to reduce the gas emission at coal face for safety, but most of the gas is discharged into the air. In this project, the following were studied: degassing boring/gas induction from bore hole/measurement in gas induction pipe, gas recovery system combined with gas induction in flyash, and installation/operation of gas engine power generation facilities (1,710kW x 7 units) with exhaust heat recovery boiler using the recovered methane gas as fuel. The results obtained were the petroleum substitution amount of 31,000 toe/y and the amount of greenhouse effect gas reduction of 480,000 t/y. In the economical estimation, the initial investment amount was 3 billion yen, the profitability of the total investment used was 2.9%, and the internal earning rate was 6.5%. (NEDO)

Improved NGL recovery designs maximize operating flexibility and product recoveries

International Nuclear Information System (INIS)

Wilkinson, J.D.; Hudson, H.M.

1992-01-01

This paper reports that the historically cyclical nature in the market for ethane and propane has demonstrated the need for flexible natural gas liquids (NGL) recovery plants. NEwly developed and patented processes are now available which can provide ultra-high recovery of ethane (95%+) when demand for ethane is high and provide essentially complete ethane rejection without the normally concomitant reduction in propane recovery. This provides plant operators the flexibility to respond more readily to NGL market conditions, thus maximizing plant operating profits. The new process designs provide this flexibility without increasing utility requirements. In fact, utility consumption is often lower when compared to conventional designs. This same process technology can also be easily retrofit into existing plants with relatively quick payout of the modifications from both recovery and efficiency improvements

Stress recovery techniques for natural element method in 2-D solid mechanics

Energy Technology Data Exchange (ETDEWEB)

Cho, Jin Rae [Dept. of Naval Architecture and Ocean Engineering, Hongik University, Sejong (Korea, Republic of)

2016-11-15

This paper is concerned with the stress recovery for the natural element method in which the problem domain is discretized with Delaunay triangles and the structural behavior is approximated with Laplace interpolation functions. Basically, the global and local patch recovery techniques based on the L2-projection method are adopted. For the local patch recovery, the local element patches are defined by the supports of each Laplace interpolation function. For the comparison purpose, the local stress recovery is also performed using Lagrange-type basis functions that are used for 3- and 6-node triangular elements. The stresses that are recovered by the present global and local recovery techniques are compared each other and compared with the available analytic solution, in terms of their spatial distributions and the convergence rates. As well, the dependence of the recovered stress field on the type of test basis functions that are used forbnov-Galerkin (BG) and Petrov-Galerkin (PG) natural element methods is also investigated.

Method for the recovery of a material

International Nuclear Information System (INIS)

Spence, A.P.

1978-01-01

The present invention relates to an improved method for the solution mining of a mineral from a subterranean formation. More specifically, the invention relates to an improved method which enhances significantly the recovery of the mineral from a subterranean formation via solution mining. The improvement comprises switching a well which initially functions as a producer to an injector and vice versa after oxidant breakthrough has occurred at a production well

Utilizing data grid architecture for the backup and recovery of clinical image data.

Science.gov (United States)

Liu, Brent J; Zhou, M Z; Documet, J

2005-01-01

Grid Computing represents the latest and most exciting technology to evolve from the familiar realm of parallel, peer-to-peer and client-server models. However, there has been limited investigation into the impact of this emerging technology in medical imaging and informatics. In particular, PACS technology, an established clinical image repository system, while having matured significantly during the past ten years, still remains weak in the area of clinical image data backup. Current solutions are expensive or time consuming and the technology is far from foolproof. Many large-scale PACS archive systems still encounter downtime for hours or days, which has the critical effect of crippling daily clinical operations. In this paper, a review of current backup solutions will be presented along with a brief introduction to grid technology. Finally, research and development utilizing the grid architecture for the recovery of clinical image data, in particular, PACS image data, will be presented. The focus of this paper is centered on applying a grid computing architecture to a DICOM environment since DICOM has become the standard for clinical image data and PACS utilizes this standard. A federation of PACS can be created allowing a failed PACS archive to recover its image data from others in the federation in a seamless fashion. The design reflects the five-layer architecture of grid computing: Fabric, Resource, Connectivity, Collective, and Application Layers. The testbed Data Grid is composed of one research laboratory and two clinical sites. The Globus 3.0 Toolkit (Co-developed by the Argonne National Laboratory and Information Sciences Institute, USC) for developing the core and user level middleware is utilized to achieve grid connectivity. The successful implementation and evaluation of utilizing data grid architecture for clinical PACS data backup and recovery will provide an understanding of the methodology for using Data Grid in clinical image data backup for

Methods to maximise recovery of environmental DNA from water samples.

Directory of Open Access Journals (Sweden)

Rheyda Hinlo

Full Text Available The environmental DNA (eDNA method is a detection technique that is rapidly gaining credibility as a sensitive tool useful in the surveillance and monitoring of invasive and threatened species. Because eDNA analysis often deals with small quantities of short and degraded DNA fragments, methods that maximize eDNA recovery are required to increase detectability. In this study, we performed experiments at different stages of the eDNA analysis to show which combinations of methods give the best recovery rate for eDNA. Using Oriental weatherloach (Misgurnus anguillicaudatus as a study species, we show that various combinations of DNA capture, preservation and extraction methods can significantly affect DNA yield. Filtration using cellulose nitrate filter paper preserved in ethanol or stored in a -20°C freezer and extracted with the Qiagen DNeasy kit outperformed other combinations in terms of cost and efficiency of DNA recovery. Our results support the recommendation to filter water samples within 24hours but if this is not possible, our results suggest that refrigeration may be a better option than freezing for short-term storage (i.e., 3-5 days. This information is useful in designing eDNA detection of low-density invasive or threatened species, where small variations in DNA recovery can signify the difference between detection success or failure.

Routine methods for post-transportation accident recovery of spent fuel casks

International Nuclear Information System (INIS)

Shappert, L.B.; Pope, R.B.; Best, R.E.; Jones, R.H.

1991-01-01

Spent fuel casks and other large radioactive material packages have been examined to determine whether the designs are adequate to allow the casks to be recovered using conventional recovery methods following a transportation accident. Casks and similar packages are typically designed with, and handled by, trunnions that support the package during transport. These trunnions are considered the best cask feature with which to grapple the cask once it is no longer in its usual shipping mode. Following a transport accident, the trunnions may be buried or entangled so that they are not readily accessible to initiate the recovery process. To evaluate the effectiveness of applying traditional recovery methods to spent fuel casks, a workshop was held in which a series of accidents involving casks were postulated; the modes of transportation considered included truck, rail, and barge. These participants knowledgeable in transport, handling, and, in some cases, recovery of large, heavy containers attended. Participants concluded that the physical recovery of a cask involved in an accident, irrespective of where the accident occurs, would be a straightforward rigging operation and that the addition of specific recovery features (e.g., additional trunnions) to the cask appears unnecessary

Recovery process of elite athletes: A review of contemporary methods

Directory of Open Access Journals (Sweden)

Veljović Draško

2012-01-01

Full Text Available A numerous training stimulus and competition as well can reduce level of abilities among athletes. This decline of performance can be a temporary phenomenon, with duration of several minutes or several hours after a workout, or take much longer, even a several days. The lack of adequate recovery process can influence on athletes not being able to train at the desired intensity or do not fully meet the tasks at the next training session. Chronic fatigue can lead to injuries, and therefore, full recovery is necessary for achieving optimal level of abilities that will ensure a better athletic performance. For this reasons, athletes often carry out a variety of techniques and methods aimed to recover after training or match. They have become a part of the training process and their purpose is reduction of stress and fatigue incurred as a result of daily exposure to intense training stimulus. There are numerous methods and techniques today that can accelerate the recovery process of athletes. For this reason it is necessary to know the efficiency of an adequate method which will be applied in the training process. The aim of this review article is to point to those currently used and their effects on the process of recovery after physical activity in elite sport.

Department of Energy plan for recovery and utilization of nuclear byproducts from defense wastes. Volume 2

Energy Technology Data Exchange (ETDEWEB)

1983-08-01

Nuclear wastes from the defense production cycle contain many uniquely useful, intrinsically valuable, and strategically important materials. These materials have a wide range of known and potential applications in food technology, agriculture, energy, public health, medicine, industrial technology, and national security. Furthermore, their removal from the nuclear waste stream can facilitate waste management and yield economic, safety, and environmental advantages in the management and disposal of the residual nuclear wastes that have no redemptive value. This document is the program plan for implementing the recovery and beneficial use of these valuable materials. An Executive Summary of this document, DOE/DP-0013, Vol. 1, January 1983, is available. Program policy, goals and strategy are stated in Section 2. Implementation tasks, schedule and funding are detailed in Section 3. The remaining five sections and the appendixes provide necessary background information to support these two sections. Section 4 reviews some of the unique properties of the individual byproduct materials and describes both demonstrated and potential applications. The amounts of byproduct materials that are available now for research and demonstration purposes, and the amounts that could be recovered in the future for expanded applications are detailed in Section 5. Section 6 describes the effects byproduct recovery and utilization have on the management and final disposal of nuclear wastes. The institutional issues that affect the recovery, processing and utilization of nuclear byproducts are discussed in Section 7. Finally, Section 8 presents a generalized mathematical process by which applications can be evaluated and prioritized (rank-ordered) to provide planning data for program management.

Department of Energy plan for recovery and utilization of nuclear byproducts from defense wastes. Volume 2

International Nuclear Information System (INIS)

1983-08-01

Nuclear wastes from the defense production cycle contain many uniquely useful, intrinsically valuable, and strategically important materials. These materials have a wide range of known and potential applications in food technology, agriculture, energy, public health, medicine, industrial technology, and national security. Furthermore, their removal from the nuclear waste stream can facilitate waste management and yield economic, safety, and environmental advantages in the management and disposal of the residual nuclear wastes that have no redemptive value. This document is the program plan for implementing the recovery and beneficial use of these valuable materials. An Executive Summary of this document, DOE/DP-0013, Vol. 1, January 1983, is available. Program policy, goals and strategy are stated in Section 2. Implementation tasks, schedule and funding are detailed in Section 3. The remaining five sections and the appendixes provide necessary background information to support these two sections. Section 4 reviews some of the unique properties of the individual byproduct materials and describes both demonstrated and potential applications. The amounts of byproduct materials that are available now for research and demonstration purposes, and the amounts that could be recovered in the future for expanded applications are detailed in Section 5. Section 6 describes the effects byproduct recovery and utilization have on the management and final disposal of nuclear wastes. The institutional issues that affect the recovery, processing and utilization of nuclear byproducts are discussed in Section 7. Finally, Section 8 presents a generalized mathematical process by which applications can be evaluated and prioritized (rank-ordered) to provide planning data for program management

Seismic data two-step recovery approach combining sparsity-promoting and hyperbolic Radon transform methods

International Nuclear Information System (INIS)

Wang, Hanchuang; Chen, Shengchang; Ren, Haoran; Liang, Donghui; Zhou, Huamin; She, Deping

2015-01-01

In current research of seismic data recovery problems, the sparsity-promoting method usually produces an insufficient recovery result at the locations of null traces. The HRT (hyperbolic Radon transform) method can be applied to problems of seismic data recovery with approximately hyperbolic events. Influenced by deviations of hyperbolic characteristics between real and ideal travel-time curves, some spurious events are usually introduced and the recovery effect of intermediate and far-offset traces is worse than that of near-offset traces. Sparsity-promoting recovery is primarily dependent on the sparsity of seismic data in the sparse transform domain (i.e. on the local waveform characteristics), whereas HRT recovery is severely affected by the global characteristics of the seismic events. Inspired by the above conclusion, a two-step recovery approach combining sparsity-promoting and time-invariant HRT methods is proposed, which is based on both local and global characteristics of the seismic data. Two implementation strategies are presented in detail, and the selection criteria of the relevant strategies is also discussed. Numerical examples of synthetic and real data verify that the new approach can achieve a better recovery effect by simultaneously overcoming the shortcomings of sparsity-promoting recovery and HRT recovery. (paper)

An optimized rapid bisulfite conversion method with high recovery of cell-free DNA.

Science.gov (United States)

Yi, Shaohua; Long, Fei; Cheng, Juanbo; Huang, Daixin

2017-12-19

Methylation analysis of cell-free DNA is a encouraging tool for tumor diagnosis, monitoring and prognosis. Sensitivity of methylation analysis is a very important matter due to the tiny amounts of cell-free DNA available in plasma. Most current methods of DNA methylation analysis are based on the difference of bisulfite-mediated deamination of cytosine between cytosine and 5-methylcytosine. However, the recovery of bisulfite-converted DNA based on current methods is very poor for the methylation analysis of cell-free DNA. We optimized a rapid method for the crucial steps of bisulfite conversion with high recovery of cell-free DNA. A rapid deamination step and alkaline desulfonation was combined with the purification of DNA on a silica column. The conversion efficiency and recovery of bisulfite-treated DNA was investigated by the droplet digital PCR. The optimization of the reaction results in complete cytosine conversion in 30 min at 70 °C and about 65% of recovery of bisulfite-treated cell-free DNA, which is higher than current methods. The method allows high recovery from low levels of bisulfite-treated cell-free DNA, enhancing the analysis sensitivity of methylation detection from cell-free DNA.

Residual nitrogen-15 recovery by corn as influenced by tillage and fertilization method

International Nuclear Information System (INIS)

Timmons, D.R.; Cruse, R.M.

1991-01-01

Tillage systems that create different surface residue conditions may also affect the recovery of residual fertilizer N during subsequent growing seasons. This study evaluated the recovery of residual labeled N fertilizer in the soil by corn (Zea mays L.) for two tillage systems and two fertilization methods. Five atom % 15 N-enriched 28% urea-ammonium nitrate solution (UAN) at 224 kg N ha -1 was either surface-applied in the fall before any primary tillage or banded (knifed in) just before planting in the spring. Continuous corn was grown with either fall moldboard-plow (MP) or ridge-till (RT) systems. After the initial growing season, the recovery of residual labeled N in the soil by corn was determined for three consecutive growing seasons, and the soil profile was sampled periodically to measure residual 15 N in the organic and inorganic pools. One year after labeled UAN application, from 16 to 27% of the initial 15 N applied was found in the organic N pool and only 1% as inorganic N[NH 4 +(NO 2 +NO 3 )-N]. After four seasons, residual 15 N in the organic N pool ranged from 13 to 24%. Less than 0.5% remained as inorganic N. Regression analyses indicated that about 5 kg 15 N ha -1 year -1 became available for both MP and RT systems with banded N, so the amounts were small. Total residual 15 N recovery by corn grain plus stover for three seasons ranged from 1.7 to 3.5%, and was greatest for spring-banded fertilizer. Because the amounts of residual 15 N utilized were too small to affect corn growth, this N source appears to be negligible when considering corn-N needs

Patient-specific prediction of functional recovery after stroke.

Science.gov (United States)

Douiri, Abdel; Grace, Justin; Sarker, Shah-Jalal; Tilling, Kate; McKevitt, Christopher; Wolfe, Charles DA; Rudd, Anthony G

2017-07-01

Background and aims Clinical predictive models for stroke recovery could offer the opportunity of targeted early intervention and more specific information for patients and carers. In this study, we developed and validated a patient-specific prognostic model for monitoring recovery after stroke and assessed its clinical utility. Methods Four hundred and ninety-five patients from the population-based South London Stroke Register were included in a substudy between 2002 and 2004. Activities of daily living were assessed using Barthel Index) at one, two, three, four, six, eight, 12, 26, and 52 weeks after stroke. Penalized linear mixed models were developed to predict patients' functional recovery trajectories. An external validation cohort included 1049 newly registered stroke patients between 2005 and 2011. Prediction errors on discrimination and calibration were assessed. The potential clinical utility was evaluated using prognostic accuracy measurements and decision curve analysis. Results Predictive recovery curves showed good accuracy, with root mean squared deviation of 3 Barthel Index points and a R 2 of 83% up to one year after stroke in the external cohort. The negative predictive values of the risk of poor recovery (Barthel Index <8) at three and 12 months were also excellent, 96% (95% CI [93.6-97.4]) and 93% [90.8-95.3], respectively, with a potential clinical utility measured by likelihood ratios (LR+:17 [10.8-26.8] at three months and LR+:11 [6.5-17.2] at 12 months). Decision curve analysis showed an increased clinical benefit, particularly at threshold probabilities of above 5% for predictive risk of poor outcomes. Conclusions A recovery curves tool seems to accurately predict progression of functional recovery in poststroke patients.

Plasma methods for metals recovery from metal-containing waste.

Science.gov (United States)

Changming, Du; Chao, Shang; Gong, Xiangjie; Ting, Wang; Xiange, Wei

2018-04-27

Metal-containing waste, a kind of new wastes, has a great potential for recycling and is also difficult to deal with. Many countries pay more and more attention to develop the metal recovery process and equipment of this kind of waste as raw material, so as to solve the environmental pollution and comprehensively utilize the discarded metal resources. Plasma processing is an efficient and environmentally friendly way for metal-containing waste. This review mainly discuss various metal-containing waste types, such as printed circuit boards (PCBs), red mud, galvanic sludge, Zircon, aluminium dross and incinerated ash, and the corresponding plasma methods, which include DC extended transferred arc plasma reactor, DC non-transferred arc plasma torch, RF thermal plasma reactor and argon and argon-hydrogen plasma jets. In addition, the plasma arc melting technology has a better purification effect on the extraction of useful metals from metal-containing wastes, a great capacity of volume reduction of waste materials, and a low leaching toxicity of solid slag, which can also be used to deal with all kinds of metal waste materials, having a wide range of applications. Copyright © 2018 Elsevier Ltd. All rights reserved.

Method for the recovery of Cr and Co species from effluents using ...

African Journals Online (AJOL)

Method for the recovery of Cr and Co species from effluents using agricultural adsorbent ... International Journal of Biological and Chemical Sciences ... recovery of Cr and Co species in microbial-treated industrial wastewater using agricultural ...

Recovery of uranium from sea water

International Nuclear Information System (INIS)

Tabushi, Iwao; Kobuke, Yoshiaki

1984-01-01

The present status of technology for the recovery of uranium has been reviewed. Adsorbent qualities were discussed in terms of three important criteria: adsorption rate, equilibrium adsorption and chemical as well as physical stability. It was elucidated that a significant improvement of the adsorption rate is most important. Efforts were made to clarify factors influencing the adsorption rate. A method to treat a tremendous amount of sea water is of much importance as well. Pumping-up and direct use of sea currents were compared with each other. It has been emphasized that the active utilization of the various advantages of the latter method is crucial for the realization of the recovery project. The physical capability of the method was illustrated. Some composite systems with electric power generation plants were also discussed. (author)

Effects of Microwave Radiation on Oil Recovery

Science.gov (United States)

Esmaeili, Abdollah

2011-12-01

A variety of oil recovery methods have been developed and applied to mature and depleted reservoirs in order to improve the efficiency. Microwave radiation oil recovery method is a relatively new method and has been of great interest in the recent years. Crude oil is typically co-mingled with suspended solids and water. To increase oil recovery, it is necessary to remove these components. The separation of oil from water and solids using gravitational settling methods is typically incomplete. Oil-in-water and oil-water-solid emulsions can be demulsified and separated into their individual layers by microwave radiation. The data also show that microwave separation is faster than gravity separation and can be faster than conventional heating at many conditions. After separation of emulsion into water and oil layers, water can be discharged and oil is collected. High-frequency microwave recycling process can recover oil and gases from oil shale, residual oil, drill cuttings, tar sands oil, contaminated dredge/sediments, tires and plastics with significantly greater yields and lower costs than are available utilizing existing known technologies. This process is environmentally friendly, fuel-generating recycler to reduce waste, cut emissions, and save energy. This paper presents a critical review of Microwave radiation method for oil recovery.

Industrial development of a simulation method for ore recovery evaluation

International Nuclear Information System (INIS)

Deraisme; De Fouquet; Fraisse

1983-01-01

The purpose of downstream geostatistics is to provide to engineers, responsible for mining project studies, with a method for predicting the ore reserve recovery coming from different mining methods and for choosing the best one according to economic criteria. In the case of the BEN LOMOND uranium deposit, the metal recovery at the production stage depends on the geometry of mineralized lenses. For the first step of this study the usual technique for constructing a numerical model of deposit has been used. But this does not reproduce the geological structures very precisely. The recovered reserves have been computed for three more or less selective mining methods. This has been done inputing the outlines of stopes on a digitalizer. In the case of a cut and fill method an automatic algorithm for the optimization under constraints has been developed [fr

Recovery of DNA from agarose gel by trap method | Xia | African ...

African Journals Online (AJOL)

Recovery of DNA from agarose gel electrophoresis is a basic operation during molecular cloning. Circular or linear DNA fragments which vary from 1.5 to 6.5 kb and correspond to 1 kb marker can be recovered from 0.8 to 1.0% agarose gel smoothly with a simple and rapid trap method. The recovery efficiency could be ...

Analytic Method for Pressure Recovery in Truncated Diffusers ...

African Journals Online (AJOL)

A prediction method is presented for the static pressure recovery in subsonic axisymmetric truncated conical diffusers. In the analysis, a turbulent boundary layer is assumed at the diffuser inlet and a potential core exists throughout the flow. When flow separation occurs, this approach cannot be used to predict the maximum ...

Method for hydrometallurgical recovery of selected metals

International Nuclear Information System (INIS)

Lorenz, G.; Schaefer, B.; Balzat, W.

1988-01-01

The method for hydrometallurgical recovery of selected metals refers to ore dressing by means of milling and alkaline leaching of metals, preferably uranium. By adding CaO during wet milling, Na + or K + ions of clayey ores are replaced by Ca 2+ ions. Due to the ion exchange processes, the uranium bonded with clays becomes more accessible to the leaching solution. The uranium yield increases and the consumption of reagents decreases

Creep compliance and percent recovery of Oklahoma certified binder using the multiple stress recovery (MSCR) method.

Science.gov (United States)

2015-04-01

A laboratory study was conducted to develop guidelines for the Multiple Stress Creep Recovery : (MSCR) test method for local conditions prevailing in Oklahoma. The study consisted of : commonly used binders in Oklahoma, namely PG 64-22, PG 70-28, and...

Optimizing the Prioritization of Natural Disaster Recovery Projects

National Research Council Canada - National Science Library

Aftanas, Jason M

2007-01-01

.... This work will focus on promoting objectivity in the project prioritizing process, improving the communication of the overall base recovery requirement, increasing efficiency in utilizing human and monetary resources, and the creation of a usable and repeatable decision-making tool based on Value-Focused Thinking and integer programming methods.

Fuel cell heat utilization system; Nenryo denchi netsuriyo sochi

Energy Technology Data Exchange (ETDEWEB)

Urata, T. [Tokyo (Japan); Omura, T. [Tokyo (Japan)

1995-07-04

In the conventional fuel cell heat utilization system, the waste heat is recovered to be utilized by either the waste heat recovery heat exchanger or the waste heat recovery steam. In the employment of the waste heat recovery heat exchanger system, however, the utility value is decreased when the temperature of the waste heat is lowered. Contrarily, in the employment of the waste heat recovery steam system, the supplementary water requirement is increased corresponding to the amount of waste heat recovery steam, resulting in the cost increase for water treatment. This invention solves the problem. In the invented fuel cell heat utilization system, a pressurized water from the steam separator is introduced into the second circuit to utilize directly the heat in the heat utilization system without employing the heat exchanger. If a blowdown valve is installed between the second circuit heat utilization system and the steam separator, the heat loss due to the blowdown can be reduced, since the low temperature water is blown down after being utilized in the heat utilization system. 4 figs.

Comparison of methods for determining the hydrologic recovery time after forest disturbance

Science.gov (United States)

Oda, T.; Green, M.; Ohte, N.; Urakawa, R.; Endo, I.; Scanlon, T. M.; Sebestyen, S. D.; McGuire, K. J.; Katsuyama, M.; Fukuzawa, K.; Tague, C.; Hiraoka, M.; Fukushima, K.; Giambelluca, T. W.

2013-12-01

Changes in forest hydrology changes after forest disturbance vary among catchments. Although studies have summarized the initial runoff changes following forest disturbance, the estimates of long-term recovery time are less frequently reported. To understand the mechanisms of long-term recovery processes and to predict the long-term changes in streamflow after forest disturbance, it is important to compare recovery times after disturbance. However, there is no clear consensus regarding the best methodology for such research, especially for watershed studies that were not designed as paired watersheds. We compared methods of determining the hydrologic recovery time to determine if there is a common method for sites in any hydroclimatic setting. We defined the hydrologic recovery time to be the time of disturbance to the time when hydrological factors first recovered to pre-disturbance levels. We acquired data on long-term rainfall and runoff at 16 sites in northeastern USA and Japan that had at least 10 years (and up to 50 years) of post disturbance data. The types of disturbance include harvesting, diseases and insect damages. We compared multiple indices of hydrological response including annual runoff, annual runoff ratio (annual runoff/annual rainfall), annual loss (annual rainfall-annual runoff), fiftieth-percentile annual flow, and seasonal water balance. The results showed that comparing annual runoff to a reference site was most robust at constraining the recovery time, followed by using pre-disturbance data as reference data and calculating the differences in annual runoff from pre-disturbance levels. However, in case of small disturbance at sites without reference data or long-term pre-disturbance data, the inter-annual variation of rainfall makes the effect of disturbance unclear. We found that annual loss had smaller inter-annual variation, and defining recovery time with annual loss was best in terms of matching the results from paired watersheds. The

Staff perceptions of borderline personality disorder and recovery: A Q-sort method approach.

Science.gov (United States)

Dean, Rebecca; Siddiqui, Sara; Beesley, Frank; Fox, John; Berry, Katherine

2018-04-16

This study was the first to explore how staff that work with people diagnosed with borderline personality disorder (BPD) perceive recovery in this client group. These views are important because of the crucial role that staff play in the care of people with BPD, and the challenges that staff experience with these clients. A Q methodology design was used, containing 58 statements about recovery. Twenty-nine mental health staff sorted recovery statements according to perceived importance to recovery in BPD. There were two different viewpoints about recovery in BPD. A medically oriented group viewed coping with symptoms and behaviours specific to BPD as being most important to recovery, whereas participants who were more well-being oriented viewed achieving overall well-being that was universally valued regardless of diagnosis as more important. Both groups reported that engaging in socially valued activities such as work and education was not an important aspect of recovery and that people with BPD could be considered to have recovered despite continued impairments in everyday functioning. Staff perceptions of recovery in BPD can differ, which poses risks for consistent team working, a particularly important issue in this client group due to the relational difficulties associated with the diagnosis. Multidisciplinary teams working with people diagnosed with BPD therefore need to find a forum to promote a shared understanding of each patient's needs and support plans. We advocate that team formulation is a promising approach to achieve more consistent ways of working within teams. Findings Multidisciplinary teams working with people with borderline personality disorder should use team formulations to create a shared understanding of individual patient's needs and goals for recovery, so they can deliver a consistent approach to care. Recovery questionnaires should be used to develop an understanding of a patient's individual recovery goals. Limitations Opportunity

Method for enhanced oil recovery

Science.gov (United States)

Comberiati, Joseph R.; Locke, Charles D.; Kamath, Krishna I.

1980-01-01

The present invention is directed to an improved method for enhanced recovery of oil from relatively "cold" reservoirs by carbon dioxide flooding. In oil reservoirs at a temperature less than the critical temperature of 87.7.degree. F. and at a pore pressure greater than the saturation pressure of carbon dioxide at the temperature of the reservoir, the carbon dioxide remains in the liquid state which does not satisfactorily mix with the oil. However, applicants have found that carbon dioxide can be vaporized in situ in the reservoir by selectively reducing the pore pressure in the reservoir to a value less than the particular saturated vapor pressure so as to greatly enhance the mixing of the carbon dioxide with the oil.

The effect of follicular fluid hormones on oocyte recovery after ovarian stimulation: FSH level predicts oocyte recovery

Directory of Open Access Journals (Sweden)

Rinaudo Paolo F

2009-04-01

Full Text Available Abstract Background Ovarian stimulation for assisted reproductive technology (ART overcomes the physiologic process to develop a single dominant follicle. However, following stimulation, egg recovery rates are not 100%. The objective of this study is to determine if the follicular fluid hormonal environment is associated with oocyte recovery. Methods This is a prospective study involving patients undergoing ART by standard ovarian stimulation protocols at an urban academic medical center. A total of 143 follicular fluid aspirates were collected from 80 patients. Concentrations of FSH, hCG, estradiol, progesterone, testosterone and prolactin were determined. A multivariable regression analysis was used to investigate the relationship between the follicular fluid hormones and oocyte recovery. Results Intrafollicular FSH was significantly associated with oocyte recovery after adjustment for hCG (Adjusted odds ratio (AOR = 1.21, 95%CI 1.03–1.42. The hCG concentration alone, in the range tested, did not impact the odds of oocyte recovery (AOR = 0.99, 95%CI 0.93–1.07. Estradiol was significantly associated with oocyte recovery (AOR = 0.98, 95% CI 0.96–0.99. After adjustment for progesterone, the strength of association between FSH and oocyte recovery increased (AOR = 1.84, 95%CI 1.45–2.34. Conclusion The relationship between FSH and oocyte recovery is significant and appears to work through mechanisms independent of the sex hormones. FSH may be important for the physiologic event of separation of the cumulus-oocyte complex from the follicle wall, thereby influencing oocyte recovery. Current methods for inducing the final stages of oocyte maturation, with hCG administration alone, may not be optimal. Modifications of treatment protocols utilizing additional FSH may enhance oocyte recovery.

Strontium-90 and promethium-147 recovery

International Nuclear Information System (INIS)

Hoisington, J.E.; McDonell, W.R.

1982-01-01

Strontium-90 and promethium-147 are fission product radionuclides with potential for use as heat source materials in high reliability, non-interruptible power supplies. Interest has recently been expressed in their utilization for Department of Defense (DOD) applications. This memorandum summarizes the current inventories, the annual production rates, and the possible recovery of Sr-90 and Pm-147 from nuclear materials production operations at Hanford and Savannah River. Recovery of these isotopes from LWR spend fuel utilizing the Barnwell Nuclear Fuels Plant (BNFP) is also considered. Unit recovery costs at each site are provided

Minimizing temperature instability of heat recovery hot water system utilizing optimized thermal energy storage

Science.gov (United States)

Suamir, I. N.; Sukadana, I. B. P.; Arsana, M. E.

2018-01-01

One energy-saving technology that starts gaining attractive for hotel industry application in Indonesia is the utilization of waste heat of a central air conditioning system to heat water for domestic hot water supply system. Implementing the technology for such application at a hotel was found that hot water capacity generated from the heat recovery system could satisfy domestic hot water demand of the hotel. The gas boilers installed in order to back up the system have never been used. The hot water supply, however, was found to be instable with hot water supply temperature fluctuated ranging from 45 °C to 62 °C. The temperature fluctuations reaches 17 °C, which is considered instable and can reduce hot water usage comfort level. This research is aimed to optimize the thermal energy storage in order to minimize the temperature instability of heat recovery hot water supply system. The research is a case study approach based on cooling and hot water demands of a hotel in Jakarta-Indonesia that has applied water cooled chillers with heat recovery systems. The hotel operation with 329 guest rooms and 8 function rooms showed that hot water production in the heat recovery system completed with 5 m3 thermal energy storage (TES) could not hold the hot water supply temperature constantly. The variations of the cooling demand and hot water demands day by day were identified. It was found that there was significant mismatched of available time (hours) between cooling demand which is directly correlated to the hot water production from the heat recovery system and hot water usage. The available TES system could not store heat rejected from the condenser of the chiller during cooling demand peak time between 14.00 and 18.00 hours. The extra heat from the heat recovery system consequently increases the temperature of hot water up to 62 °C. It is about 12 K above 50 °C the requirement hot water temperature of the hotel. In contrast, the TES could not deliver proper

Post-marathon wearing of Masai Barefoot Technology shoes facilitates recovery from race-induced fatigue: an evaluation utilizing a visual analog scale

Directory of Open Access Journals (Sweden)

Nakagawa K

2014-12-01

Full Text Available Kento Nakagawa, Takashi Obu, Kazuyuki KanosueFaculty of Sport Sciences, Waseda University, Tokorozawa, Saitama, Japan Purpose: To investigate the potential benefit of post-race wearing of unstable shoes (Masai Barefoot Technology [MBT] on recovery from marathon race–induced fatigue.Patients and methods: Forty-five runners who participated in a full marathon race were divided into three groups: 1 MBT shoes, 2 trail running shoes, and 3 control (CON. Participants ran a full marathon with their own running shoes, and then put on the assigned shoes immediately after the race. They continued to wear the assigned shoes for the ensuing 3 days. The CON group wore their usual shoes. Estimates of post-race fatigue were made by the participants on questionnaires that utilized a visual analog scale. Estimates were made just after the race, as well as for the next 3 days.Results: The subjective fatigue of the MBT group was lower than that of the CON (P<0.05 or trail running shoe groups (P<0.05 on day 3.Conclusion: MBT shoe intervention can promote recovery from the fatigue induced by running a full marathon.Keywords: footwear, VAS, full marathon

An improved cell recovery method for iron oxidizing bacterial (IOB) enrichments

DEFF Research Database (Denmark)

Yu, Ran; Graf, Joerg; Smets, Barth F.

2008-01-01

Two cell recovery methods for IOB enrichments were evaluated for DNA extraction and further PCR-based 16S rRNA gene clone library creation. One was a published method consisting of heating plus oxalic acid treatment and the other one was a new method based on enzymatic agarose digestion (using β...

Method for the secondary recovery of petroleum

Energy Technology Data Exchange (ETDEWEB)

Roth, H H

1966-10-11

A method for the secondary recovery of petroleum from subterranean formations consists of flooding these formations with aqueous fluids. These aqueous fluids contain one or more saline solutes which are either present before the flooding or which are dissolved from the formation during flooding. These fluids contain, as a thickening agent, a substantially linear, high molecular weight, water-soluble alkenylaromatic polymer which has sulfonic acid or sulfonate groups on the aromatic nuclei. This saline solute and polymer are mutually compatible. (5 claims)

Supplier Selection Using Weighted Utility Additive Method

Science.gov (United States)

Karande, Prasad; Chakraborty, Shankar

2015-10-01

Supplier selection is a multi-criteria decision-making (MCDM) problem which mainly involves evaluating a number of available suppliers according to a set of common criteria for choosing the best one to meet the organizational needs. For any manufacturing or service organization, selecting the right upstream suppliers is a key success factor that will significantly reduce purchasing cost, increase downstream customer satisfaction and improve competitive ability. The past researchers have attempted to solve the supplier selection problem employing different MCDM techniques which involve active participation of the decision makers in the decision-making process. This paper deals with the application of weighted utility additive (WUTA) method for solving supplier selection problems. The WUTA method, an extension of utility additive approach, is based on ordinal regression and consists of building a piece-wise linear additive decision model from a preference structure using linear programming (LP). It adopts preference disaggregation principle and addresses the decision-making activities through operational models which need implicit preferences in the form of a preorder of reference alternatives or a subset of these alternatives present in the process. The preferential preorder provided by the decision maker is used as a restriction of a LP problem, which has its own objective function, minimization of the sum of the errors associated with the ranking of each alternative. Based on a given reference ranking of alternatives, one or more additive utility functions are derived. Using these utility functions, the weighted utilities for individual criterion values are combined into an overall weighted utility for a given alternative. It is observed that WUTA method, having a sound mathematical background, can provide accurate ranking to the candidate suppliers and choose the best one to fulfill the organizational requirements. Two real time examples are illustrated to prove

Qualitative Methods in Drug Utilization Research

DEFF Research Database (Denmark)

Almarsdóttir, Anna Birna; Bastholm Rahmner, Pia

2016-01-01

Qualitative research methods derive from the social sciences. Their use in drug utilization research is increasingly widespread, especially in understanding patient and prescriber perspectives. The main focus in qualitative research is exploration of a given phenomenon in order to get a wider...... understanding of why and how it appears. Qualitative research methods build on various theoretical underpinnings/schools of thought. The same validity and quality criteria cannot be used for both qualitative and quantitative methods....

Acute Effect of Lower-Body Vibration as a Recovery Method After Fatiguing Exercise

Directory of Open Access Journals (Sweden)

Svetlana Nepocatych

2015-09-01

Full Text Available The purpose of this study was to compare three recovery methods: control (CON, lower-body vibration (LBV and LBV+ local muscle cooling (LBVC on lower-body performance, perceived recovery, and muscle soreness. Physically active male volunteers (n=8 in a repeated-measures, counterbalanced design, completed three sets of squats to fatigue, each recovery treatment, and two Wingate Anaerobic Tests. Rating of perceived exertion (RPE, and heart rate (HR were measured after fatiguing exercise, recovery treatment and Wingate Anaerobic tests. Peak and mean power, fatigue index, Delayed Onset Muscle Soreness (DOMS, and comfort levels were compared between each treatment. In Wingate 1, no significant differences (p=0.42 were found among CON, LBV, or LBVC regarding peak power (1119±239, 1097±225, and 1146±260 W, respectively, mean power (p=0.32, or fatigue index (p=0.47. In Wingate 2, no significant (p=0.17 differences were found among CON, LBV, or LBVC regarding peak power (1042±228, 1078±233, and 1110±268 W, respectively, mean power (p=0.38, or fatigue index (p=0.15. A significantly better (p=0.01 perceived recovery was observed after LBV (6±1 and LBVC (6±1 compared to CON (4±1. The study findings support psychological but not performance enhancing benefits after the use of LBV and LBVC as recovery methods.

Hepatic mitochondrial and microsomal recovery of rats intoxicated with CCl/sub 4/

Energy Technology Data Exchange (ETDEWEB)

Hasegawa, T.; Hirai, Y.; Koga, N.; Tomokuni, K.

1983-01-01

The hepatic mitochondrial and microsomal recovery of rats intoxicated with CCl/sub 4/ was investigated with specific reference to the oxygen utilization of liver slices. In control rats, the major oxygen utilization of the liver slices was attributed to mitochondrial particles. Since the mitochondrial oxygen utilization was inhibited by cyanide, the microsomal oxygen utilization was induced by NADPH and phenobarbital (a substrate for microsomal mixed function oxidase). Changes in oxygen utilization were observed in the recovery course of rats intoxicated with CCl/sub 4/, and the recovery of mitochondria was found to be faster than that of microsomes. A sex difference was present in the recovery mechanism of the microsomes.

Method for the removal and recovery of mercury

Science.gov (United States)

Easterly, Clay E.; Vass, Arpad A.; Tyndall, Richard L.

1997-01-01

The present invention is an enhanced method for the removal and recovery of mercury from mercury-contaminated matrices. The method involves contacting a mercury-contaminated matrix with an aqueous dispersant solution derived from specific intra-amoebic isolates to release the mercury from the mercury-contaminated matrix and emulsify the mercury; then, contacting the matrix with an amalgamating metal from a metal source to amalgamate the mercury to the amalgamating metal; removing the metallic source from the mercury-contaminated matrix; and heating the metallic source to vaporize the mercury in a closed system to capture the mercury vapors.

RE-UTILIZATION OF INORGANIC SOLID WASTE (LIME MUD AS FOREST ROAD STABILIZER FROM THE CHEMICAL RECOVERY PROCESS IN KRAFT PULP MILL

Directory of Open Access Journals (Sweden)

Habip Eroğlu

2005-04-01

Full Text Available Waste handling is a concern in all pulp and paper mills. Best available techniques for reducing waste is to minimize the generation of solid waste and/or reuse these materials, wherever practicable. One of the most important solid wastes is lime mud which is generated from the kraft pulping in its chemical recovery process. This paper explores the composition of lime mud resulting from the chemical recovery unite of kraft pulp mill and investigation of this waste for re-using beneficially on sub grade and pavement of forest road as a alternative disposal method. Lime mud obtained from the re-causticising process in SEKA pulp mill that utilizes wheat straw and reed as the principal raw material was supplied with % 47 water content and its chemical and physical characterisations was performed according to standard methods. Dried waste to environmental condition was mixed with certain amount to composite cement for using on pavement and sandy clay, loamy clay and clay soils for enriching forest road sub grade properties. In order to investigate the lime mud addition on pavement and sub grade properties necessary physical tests were performed. As a consequence this study reveals that while waste of lime mud causes environmental and economical problem with conventional disposal techniques and/or abandoning to environment, this waste can be used as good stabilisation materials on forest road sub-grade and pavement without any environmental problem.

Optimization of the purification methods for recovery of recombinant growth hormone from Paralichthys olivaceus

Science.gov (United States)

Zang, Xiaonan; Zhang, Xuecheng; Mu, Xiaosheng; Liu, Bin

2013-03-01

This study aimed to optimize the purification of recombinant growth hormone from Paralichthys olivaceus. Recombinant flounder growth hormone (r-fGH) was expressed by Escherichia coli in form of inclusion body or as soluble protein under different inducing conditions. The inclusion body was renatured using two recovery methods, i.e., dilution and dialysis. Thereafter, the refolded protein was purified by Glutathione Sepharase 4B affinity chromatography and r-fGH was obtained by cleavage of thrombin. For soluble products, r-fGH was directly purified from the lysates by Glutathione Sepharase 4B affinity chromatography. ELISA-receptor assay demonstrated that despite its low receptor binding activity, the r-fGH purified from refolded inclusion body had a higher yield (2.605 mg L-1) than that from soluble protein (1.964 mg L-1). Of the tested recovery methods, addition of renaturing buffer (pH 8.5) into denatured inclusion body yielded the best recovery rate (17.9%). This work provided an optimized purification method for high recovery of r-fGH, thus contributing to the application of r-fGH to aquaculture.

Optimal control of Formula One car energy recovery systems

Science.gov (United States)

Limebeer, D. J. N.; Perantoni, G.; Rao, A. V.

2014-10-01

The utility of orthogonal collocation methods in the solution of optimal control problems relating to Formula One racing is demonstrated. These methods can be used to optimise driver controls such as the steering, braking and throttle usage, and to optimise vehicle parameters such as the aerodynamic down force and mass distributions. Of particular interest is the optimal usage of energy recovery systems (ERSs). Contemporary kinetic energy recovery systems are studied and compared with future hybrid kinetic and thermal/heat ERSs known as ERS-K and ERS-H, respectively. It is demonstrated that these systems, when properly controlled, can produce contemporary lap time using approximately two-thirds of the fuel required by earlier generation (2013 and prior) vehicles.

Data warehousing methods and processing infrastructure for brain recovery research.

Science.gov (United States)

Gee, T; Kenny, S; Price, C J; Seghier, M L; Small, S L; Leff, A P; Pacurar, A; Strother, S C

2010-09-01

In order to accelerate translational neuroscience with the goal of improving clinical care it has become important to support rapid accumulation and analysis of large, heterogeneous neuroimaging samples and their metadata from both normal control and patient groups. We propose a multi-centre, multinational approach to accelerate the data mining of large samples and facilitate data-led clinical translation of neuroimaging results in stroke. Such data-driven approaches are likely to have an early impact on clinically relevant brain recovery while we simultaneously pursue the much more challenging model-based approaches that depend on a deep understanding of the complex neural circuitry and physiological processes that support brain function and recovery. We present a brief overview of three (potentially converging) approaches to neuroimaging data warehousing and processing that aim to support these diverse methods for facilitating prediction of cognitive and behavioral recovery after stroke, or other types of brain injury or disease.

Silver recovery from the waste materials by the method of flotation process

OpenAIRE

B. Oleksiak; G. Siwiec; A. Tomaszewska; D. Piękoś

2018-01-01

During the leaching process of zinc concentrates, the waste materials rich in various metals such as eg. silver are produced. So far no attempts of silver recovery from the mentioned waste materials have been made due to the lack of any method which would be both effective and beneficial. The paper presents some possibilities of application of flotation process in silver recovery form waste materials generated during zinc production.

Dietetic- nutritional, physical and physiological recovery methods post-competition in team sports. A review.

Science.gov (United States)

Terrados, Nicolas; Mielgo-Ayuso, Juan; Delextrat, Anne; Ostojic, Sergej M; Calleja-González, Julio

2018-03-27

To a proper recovery, is absolutely necessary to know that athletes with enhanced recovery after maximal exercise are likely to perform better in sports. Recovery strategies are commonly used in team sports despite limited scientific evidence to support their effectiveness in facilitating optimal recovery and the players spend a much greater proportion of their time recovering than they do in training. According to authors, some studies investigated the effect of recovery strategies on physical performance in team sports, lack of experimental studies about the real origin of the fatigue, certify the need for further study this phenomenon. Thus, developing effective methods for helping athletes to recover is deemed essential. Therefore, the aim of this review is provide information for his practical application, based on scientific evidence about recovery in team sports.

Methods of silver recovery from radiographs - comparative study

Science.gov (United States)

Canda, L. R.; Ardelean, E.; Hepuţ, T.

2018-01-01

Management and recovery of waste are activities with multiple impacts: technologically (by using waste on current production flows, thus replacing poor raw materials), economically (can substantially reduce manufacturing costs by recycling waste), social (by creating new jobs where it is necessary to process the waste in a form more suited to technological flows) and ecologically (by removing waste that is currently produced or already stored - but poses a threat to the health of the population and / or to the environment). This is also the case for medical waste, for example radiographs, which are currently produced in large quantities, for which replacement solutions are sought, but are currently stored by archiving in hospital units. The paper presents two methods used for this kind of waste management, the result being the recovery of silver, material with applications and with increasing price, but also the proper disposal of the polymeric support. This analysis aims at developing a more efficient recycling technology for medical radiographs.

Silver recovery from the waste materials by the method of flotation process

Directory of Open Access Journals (Sweden)

B. Oleksiak

2018-01-01

Full Text Available During the leaching process of zinc concentrates, the waste materials rich in various metals such as eg. silver are produced. So far no attempts of silver recovery from the mentioned waste materials have been made due to the lack of any method which would be both effective and beneficial. The paper presents some possibilities of application of flotation process in silver recovery form waste materials generated during zinc production.

Digital recovery management: Characterizing recovery-specific social network site participation and perceived benefit.

Science.gov (United States)

Bergman, Brandon G; Kelly, Nathaniel W; Hoeppner, Bettina B; Vilsaint, Corrie L; Kelly, John F

2017-06-01

Research shows that digital social network sites (SNSs) may be valuable platforms to effect health behavior change. Little is known specifically about their ability to help address alcohol and other drug problems. This gap is noteworthy, given that individuals are already participating in existing, recovery-specific SNSs (hereafter referred to as recovery SNSs): online communities with the functionality of conventional SNSs (e.g., Facebook) that focus on substance use disorder (SUD) recovery. For example, InTheRooms.com (ITR) is a large, well-known recovery SNS that is available for free 24 hr/day via website and mobile smartphone applications. It offers recovery tools within a digital social milieu for over 430,000 registered users. To augment the knowledge base on recovery SNS platforms, we conducted an online survey of 123 ITR participants (M = 50.8 years old; 56.9% female; 93.5% White; M = 7.3 years of abstinence, range of 0-30 years; 65% cited alcohol as their primary substance). Respondents engaged with ITR, on average, for about 30 min/day several times each week. Daily meditation prompts and live online video meetings were the most commonly utilized resources. Participants generally endorsed ITR as a helpful platform, particularly with respect to increased abstinence/recovery motivation and self-efficacy. Compared to individuals abstinent for 1 or more years, those abstinent less than 1 year (including nonabstinent individuals) showed similar rates of engagement with ITR activities and similar levels of perceived benefit. Our findings suggest that longitudinal studies are warranted to examine the clinical utility of ITR and other recovery SNSs as SUD treatment adjuncts and/or recovery self-management tools. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Comparative Effects of Biomass Pre-Treatments for Direct and Indirect Transesterification to Enhance Microalgal Lipid Recovery

International Nuclear Information System (INIS)

Ghasemi Naghdi, Forough; Thomas-Hall, Skye R.; Durairatnam, Reuben; Pratt, Steven; Schenk, Peer M.

2014-01-01

Microalgal lipid recovery for biodiesel production is currently considered suboptimal, but pre-treatment of algal biomass, the use of solvent mixtures and the positioning of transesterification can lead to increased yields. Here, the effect of various reportedly successful pre-treatments and solvent mixtures were directly compared to each other and combined with direct and indirect transesterification methods using the oleaginous microalga Tetraselmis sp. M8. Microwave and thermal pre-treatments were applied and the total lipid and fatty acid methyl ester (FAME) recoveries were investigated. The application of pre-treatments increased FAME recovery through indirect transesterification when a Soxhlet system was used but they had no significant effect for direct transesterification. Gravimetric analyses of total lipids revealed that lipid recovery was highest when utilizing the chloroform-based Bligh and Dyer extraction method; however, FAME yield was the highest when applying a Soxhlet system utilizing a solvent mixture of hexane–ethanol (3:1). Total lipid recovery did not necessarily correlate with the recovery of FAMEs. The highest FAME recovery was achieved from thermal or microwave pre-treated biomass followed by indirect transesterification through Soxhlet extraction. FAME recovery could be more than doubled (increase of up to 171%) under these conditions. We conclude that a simple thermal pre-treatment (80°C for 10 min) in combination with solvent mixture extraction through indirect transesterification may present a cost-effective and scalable option for large-scale lipid extraction from microalgae.

Comparative effects of biomass pre-treatments for direct and indirect transesterification to enhance microalgal lipid recovery

Directory of Open Access Journals (Sweden)

Forough eGhasemi Naghdi

2014-12-01

Full Text Available Microalgal lipid recovery for biodiesel production is currently considered suboptimal, but pre-treatment of algal biomass, the use of solvent mixtures and the positioning of transesterification can lead to increased yields. Here, the effect of various reportedly successful pre-treatments and solvent mixtures were directly compared to each other and combined with direct and indirect transesterification methods using the oleaginous microalga Tetraselmis sp. M8. Microwave and thermal pre-treatments were applied and the total lipid and fatty acid methyl ester (FAME recoveries were investigated. The application of pre-treatments increased FAME recovery through indirect transesterification when a Soxhlet system was used but they had no significant effect for direct transesterification. Gravimetric analyses of total lipids revealed that lipid recovery was highest when utilizing the chloroform-based Bligh and Dyer extraction method; however FAME yield was the highest when applying a Soxhlet system utilizing a solvent mixture of hexane-ethanol (3:1. Total lipid recovery did not necessarily correlate with the recovery of FAMEs. The highest FAME recovery was achieved from thermal or microwave pre-treated biomass followed by indirect transesterification through Soxhlet extraction. FAME recovery could be more than doubled (increase of up to 171% under these conditions. We conclude that a simple thermal pre-treatment (80°C for 10 min in combination with solvent mixture extraction through indirect transesterification may present a cost-effective and scalable option for large-scale lipid extraction from microalgae.

Comparative Effects of Biomass Pre-Treatments for Direct and Indirect Transesterification to Enhance Microalgal Lipid Recovery

Energy Technology Data Exchange (ETDEWEB)

Ghasemi Naghdi, Forough; Thomas-Hall, Skye R.; Durairatnam, Reuben [Algae Biotechnology Laboratory, School of Agriculture and Food Sciences, The University of Queensland, Brisbane, QLD (Australia); Pratt, Steven [School of Chemical Engineering, The University of Queensland, Brisbane, QLD (Australia); Schenk, Peer M., E-mail: p.schenk@uq.edu.au [Algae Biotechnology Laboratory, School of Agriculture and Food Sciences, The University of Queensland, Brisbane, QLD (Australia)

2014-12-04

Microalgal lipid recovery for biodiesel production is currently considered suboptimal, but pre-treatment of algal biomass, the use of solvent mixtures and the positioning of transesterification can lead to increased yields. Here, the effect of various reportedly successful pre-treatments and solvent mixtures were directly compared to each other and combined with direct and indirect transesterification methods using the oleaginous microalga Tetraselmis sp. M8. Microwave and thermal pre-treatments were applied and the total lipid and fatty acid methyl ester (FAME) recoveries were investigated. The application of pre-treatments increased FAME recovery through indirect transesterification when a Soxhlet system was used but they had no significant effect for direct transesterification. Gravimetric analyses of total lipids revealed that lipid recovery was highest when utilizing the chloroform-based Bligh and Dyer extraction method; however, FAME yield was the highest when applying a Soxhlet system utilizing a solvent mixture of hexane–ethanol (3:1). Total lipid recovery did not necessarily correlate with the recovery of FAMEs. The highest FAME recovery was achieved from thermal or microwave pre-treated biomass followed by indirect transesterification through Soxhlet extraction. FAME recovery could be more than doubled (increase of up to 171%) under these conditions. We conclude that a simple thermal pre-treatment (80°C for 10 min) in combination with solvent mixture extraction through indirect transesterification may present a cost-effective and scalable option for large-scale lipid extraction from microalgae.

Reconstructing Sikh Spirituality in Recovery from Alcohol Addiction

Directory of Open Access Journals (Sweden)

Asesha Morjaria-Keval

2015-03-01

Full Text Available This paper situates Sikh identity, spirituality, and recovery from alcohol addiction within a nexus of complex social, psychological, and cultural factors. The way in which affected people in Sikh communities in Britain are able to locate and utilize unofficial recovery trajectories, often successfully alleviating suffering, presents both academic research and service provision with potential puzzles. While Sikh communities have been long settled in the UK, there is still a dearth of extensive, multi-method, and analytically rich research investigating the role of spirituality and Sikh identity. We present existing models of recovery process and locate them against an individual psychological and sociological backdrop, so that through the use of spirituality, recovery along this route is interpreted as having both otherworldly as well as materially grounded formations. It is this duality, we argue, that is prominent socially, culturally, and psychologically as important in the recovery from addiction. The multi-factorial nature of this mechanism of change raises important questions for not only addiction recovery, but also notions of continuity and change in Sikh identity. We aim to contribute to this growing body of work in order to re-situate the role of spirituality and identity in alcohol addiction recovery.

Spectrum recovery method based on sparse representation for segmented multi-Gaussian model

Science.gov (United States)

Teng, Yidan; Zhang, Ye; Ti, Chunli; Su, Nan

2016-09-01

Hyperspectral images can realize crackajack features discriminability for supplying diagnostic characteristics with high spectral resolution. However, various degradations may generate negative influence on the spectral information, including water absorption, bands-continuous noise. On the other hand, the huge data volume and strong redundancy among spectrums produced intense demand on compressing HSIs in spectral dimension, which also leads to the loss of spectral information. The reconstruction of spectral diagnostic characteristics has irreplaceable significance for the subsequent application of HSIs. This paper introduces a spectrum restoration method for HSIs making use of segmented multi-Gaussian model (SMGM) and sparse representation. A SMGM is established to indicating the unsymmetrical spectral absorption and reflection characteristics, meanwhile, its rationality and sparse property are discussed. With the application of compressed sensing (CS) theory, we implement sparse representation to the SMGM. Then, the degraded and compressed HSIs can be reconstructed utilizing the uninjured or key bands. Finally, we take low rank matrix recovery (LRMR) algorithm for post processing to restore the spatial details. The proposed method was tested on the spectral data captured on the ground with artificial water absorption condition and an AVIRIS-HSI data set. The experimental results in terms of qualitative and quantitative assessments demonstrate that the effectiveness on recovering the spectral information from both degradations and loss compression. The spectral diagnostic characteristics and the spatial geometry feature are well preserved.

Precious Metals Recovery from Electroplating Wastewater: A Review

Science.gov (United States)

Azmi, A. A.; Jai, J.; Zamanhuri, N. A.; Yahya, A.

2018-05-01

Metal bearing electroplating wastewater posts great health and environmental concerns, but could also provide opportunities for precious and valuable metal recovery, which can make the treatment process more cost-effective and sustainable. Current conventional electroplating wastewater treatment and metal recovery methods include chemical precipitation, coagulation and flocculation, ion exchange, membrane filtration, adsorption, electrochemical treatment and photocatalysis. However, these physico-chemical methods have several disadvantages such as high initial capital cost, high operational cost due to expensive chemical reagents and electricity supply, generation of metal complexes sludge which requires further treatment, ineffective in diluted and/or concentrated wastewater, low precious metal selectivity, and slow recovery process. On the other hand, metal bio-reduction assisted by bioactive phytochemical compounds extracted from plants and plant parts is a new found technology explored by several researchers in recent years aiming to recover precious and valuable metals from secondary sources mainly industrial wastewater by utilizing low-cost and eco-friendly biomaterials as reagents. Extract of plants contains polyphenolic compounds which have great antioxidant properties and reducing capacities, able to reduce metal ions into zerovalent metal atoms and stabilize the metal particles formed. This green bio-recovery method has a value added in their end products since the metals are recovered in nano-sized particles which are more valuable and have high commercial demand in other fields ranging from electrochemistry to medicine.

Conceptual design of krypton recovery plant by porous membrane method

International Nuclear Information System (INIS)

Yoshida, Hiroshi; Fujine, Sachio; Shimizu, Toku; Saito, Keiichiro; Ouchi, Misao

1979-10-01

A conceptual design of a krypton recovery plant by porous membrane method was made to study feasibility of treating fuel reprocessing off-gas. Specifications of the plant could be clarified, such as off-gas pretreatment system, first cascade system of gaseous diffusion Hertz cascade composed of two-compartment diffusers, storage system, shield and housing and operating conditions. Capital costs and operating costs of the plant were estimated for different operating conditions and cost parameters. Technical and economic feasibility of the method compares favorably with those of the cryogenic distillation or the solvent absorption method. (author)

Development of {sup 99m}Tc extraction-recovery by solvent extraction method

Energy Technology Data Exchange (ETDEWEB)

Kimura, Akihiro; Nishikata, Kaori; Izumo, Hironobu; Tsuchiya, Kunihiko; Ishihara, Masahiro [Japan Atomic Energy Agency, Oarai Research and Development Center, Oarai, Ibaraki (Japan); Tanase, Masakazu; Fujisaki, Saburo; Shiina, Takayuki; Ohta, Akio; Takeuchi, Nobuhiro [Chiyoda Technol Corp., Tokyo (Japan)

2012-03-15

{sup 99m}Tc is used as a radiopharmaceutical in the medical field for the diagnosis, and manufactured from {sup 99}Mo, the parent nuclide. In this study, the solvent extraction with MEK was selected, and preliminary experiments were carried out using Re instead of {sup 99m}Tc. Two tests were carried out in the experiments; the one is the Re extraction test with MEK from Re-Mo solution, the other is the Re recovery test from the Re-MEK. As to the Re extraction test, and it was clear that the Re extraction yield was more than 90%. Two kinds of Re recovery tests, which are an evaporation method using the evaporator and an adsorption/elution method using the alumina column, were carried out. As to the evaporation method, the Re concentration in the collected solution increased more than 150 times. As to the adsorption/elution method, the Re concentration increased in the eluted solution more than 20 times. (author)

IRP methods for Environmental Impact Statements of utility expansion plans

International Nuclear Information System (INIS)

Cavallo, J.D.; Hemphill, R.C.; Veselka, T.D.

1992-01-01

Most large electric utilities and a growing number of gas utilities in the United States are using a planning method -- Integrated Resource Planning (IRP) - which incorporates demand-side management (DSM) programs whenever the marginal cost of the DSM programs are lower than the marginal cost of supply-side expansion options. Argonne National Laboratory has applied the IRP method in its socio-economic analysis of an Environmental Impact Statement (EIS) of power marketing for a system of electric utilities in the mountain and western regions of the United States. Applying the IRP methods provides valuable information to the participants in an EIS process involving capacity expansion of an electric or gas utility. The major challenges of applying the IRP method within an EIS are the time consuming and costly task of developing a least cost expansion path for each altemative, the detailed quantification of environmental damages associated with capacity expansion, and the explicit inclusion of societal-impacts to the region

Protein recovery from inclusion bodies of Escherichia coli using mild solubilization process.

Science.gov (United States)

Singh, Anupam; Upadhyay, Vaibhav; Upadhyay, Arun Kumar; Singh, Surinder Mohan; Panda, Amulya Kumar

2015-03-25

Formation of inclusion bodies in bacterial hosts poses a major challenge for large scale recovery of bioactive proteins. The process of obtaining bioactive protein from inclusion bodies is labor intensive and the yields of recombinant protein are often low. Here we review the developments in the field that are targeted at improving the yield, as well as quality of the recombinant protein by optimizing the individual steps of the process, especially solubilization of the inclusion bodies and refolding of the solubilized protein. Mild solubilization methods have been discussed which are based on the understanding of the fact that protein molecules in inclusion body aggregates have native-like structure. These methods solubilize the inclusion body aggregates while preserving the native-like protein structure. Subsequent protein refolding and purification results in high recovery of bioactive protein. Other parameters which influence the overall recovery of bioactive protein from inclusion bodies have also been discussed. A schematic model describing the utility of mild solubilization methods for high throughput recovery of bioactive protein has also been presented.

Application of a precipitation method for uranium recovery from Abu-Zaabal phosphoric acid plant, egypt

International Nuclear Information System (INIS)

El-Hazek, N.M.T.; Hussein, E.M.

1997-01-01

Current industrial recovery of uranium from 30% phosphoric acid-produced by the dihydrate process-is based on solvent extraction method. Uranium recovery from concentrated phosphoric acid (45-52% P 2 O 5 ) produced by evaporation of the 30% acid or directly produced by the hemihydrate process, by solvent extraction is difficult to apply in practice. In addition to possible contamination of the acid by the organic solvents and/or their deterioration. This paper investigates the possibility of applying a precipitation method (Weterings and Janssen, 1985) for uranium recovery from both low (28% P 2 O 2 ) and high (48% P 2 O 5 ) concentration phosphoric acids produced by abu-Zaabal phosphoric acid plant (abu-Zaabal fertilizers and chemicals Co., Egypt). The 28% acid produced by H 2 SO 4 dihydrate method and the 48% acid produced by evaporation of the 28% acid

Oil recovery from naturally fractured reservoirs by steam injection methods. Final report

Energy Technology Data Exchange (ETDEWEB)

Reis, J.C.; Miller, M.A.

1995-05-01

Oil recovery by steam injection is a proven, successful technology for nonfractured reservoirs, but has received only limited study for fractured reservoirs. Preliminary studies suggest recovery efficiencies in fractured reservoirs may be increased by as much as 50% with the application of steam relative to that of low temperature processes. The key mechanisms enhancing oil production at high temperature are the differential thermal expansion between oil and the pore volume, and the generation of gases within matrix blocks. Other mechanisms may also contribute to increased production. These mechanisms are relatively independent of oil gravity, making steam injection into naturally fractured reservoirs equally attractive to light and heavy oil deposits. The objectives of this research program are to quantify the amount of oil expelled by these recovery mechanisms and to develop a numerical model for predicting oil recovery in naturally fractured reservoirs during steam injection. The experimental study consists of constructing and operating several apparatuses to isolate each of these mechanisms. The first measures thermal expansion and capillary imbibition rates at relatively low temperature, but for various lithologies and matrix block shapes. The second apparatus measures the same parameters, but at high temperatures and for only one shape. A third experimental apparatus measures the maximum gas saturations that could build up within a matrix block. A fourth apparatus measures thermal conductivity and diffusivity of porous media. The numerical study consists of developing transfer functions for oil expulsion from matrix blocks to fractures at high temperatures and incorporating them, along with the energy equation, into a dual porosity thermal reservoir simulator. This simulator can be utilized to make predictions for steam injection processes in naturally-fractured reservoirs. Analytical models for capillary imbibition have also been developed.

Targeting heat recovery and reuse in industrial zone

Directory of Open Access Journals (Sweden)

Zarić Milana M.

2017-01-01

Full Text Available In order to reduce the usage of fossil fuels in industrial sectors by meeting the requirements of production processes, new heat integration and heat recovery approaches are developed. The goal of this study is to develop an approach to increase energy efficiency of an industrial zone by recovering and reusing waste heat via indirect heat integration. Industrial zones usually consist of multiple independent plants, where each plant is supplied by an independent utility system, as a decentralized system. In this study, a new approach is developed to target minimum energy requirements where an industrial zone would be supplied by a centralized utility system instead of decentralized utility system. The approach assumes that all process plants in an industrial zone are linked through the central utility system. This method is formulated as a linear programming problem (LP. Moreover, the proposed method may be used for decision making related to energy integration strategy of an industrial zone. In addition, the proposed method was applied on a case study. The results revealed that saving of fossil fuel could be achieved. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. OI172063

RPC gas recovery by open loop method

Energy Technology Data Exchange (ETDEWEB)

Joshi, Avinash [Alpha Pneumatics, 11, Krishna Kutir, Madanlal Dhigra Road, Panch Pakhadi (India)], E-mail: alpha_pneumatics@hotmail.com

2009-05-01

RPC detectors require to be flushed with small but continuous flow of gas mixture. Dealing with large number of detectors, gas consumption to very large volumes. Gas flow is a running expense and constituent gases are too expensive to be treated as consumables. Exhaust gas mixture from detectors is a potential environmental hazard if discharged directly into the atmosphere. Storage of gases on a large scale also leads to inventory- and safety-related problems. A solution to these problems is the recovery and reuse of exhaust gas mixture from RPC detectors. Close loop method employs recirculation of exhausted gas mixture after purification, analysis and addition of top-up quantities. In open loop method, under consideration here, individual component gases are separated from gas mixture and reused as source. During open loop process, gases liquefiable at low pressures are separated from ones liquefiable at high pressure. The gas phase components within each group are successively separated by either fractional condensation or gravity separation. Gas mixture coming from RPC exhaust is first desiccated by passage through molecular sieve adsorbent type (3A+4A). Subsequent scrubbing over basic activated alumina removes toxic and acidic contaminants such as S{sub 2}F{sub 10} produced during corona (arcing) discharge. In the first stage of separation isobutane and freon are concentrated by diffusion and liquefied by fractional condensation by cooling upto -30 deg. C. Liquefied gases are returned to source tanks. In the second stage of separation, argon and sulphur hexafluoride, the residual gases, are concentrated by settling due to density difference. SF{sub 6} is stored for recovery by condensation at high pressure while argon is further purified by thermal cracking of crossover impurities at 1000 deg. C followed by wet scrubbing.

RPC gas recovery by open loop method

International Nuclear Information System (INIS)

Joshi, Avinash

2009-01-01

RPC detectors require to be flushed with small but continuous flow of gas mixture. Dealing with large number of detectors, gas consumption to very large volumes. Gas flow is a running expense and constituent gases are too expensive to be treated as consumables. Exhaust gas mixture from detectors is a potential environmental hazard if discharged directly into the atmosphere. Storage of gases on a large scale also leads to inventory- and safety-related problems. A solution to these problems is the recovery and reuse of exhaust gas mixture from RPC detectors. Close loop method employs recirculation of exhausted gas mixture after purification, analysis and addition of top-up quantities. In open loop method, under consideration here, individual component gases are separated from gas mixture and reused as source. During open loop process, gases liquefiable at low pressures are separated from ones liquefiable at high pressure. The gas phase components within each group are successively separated by either fractional condensation or gravity separation. Gas mixture coming from RPC exhaust is first desiccated by passage through molecular sieve adsorbent type (3A+4A). Subsequent scrubbing over basic activated alumina removes toxic and acidic contaminants such as S 2 F 10 produced during corona (arcing) discharge. In the first stage of separation isobutane and freon are concentrated by diffusion and liquefied by fractional condensation by cooling upto -30 deg. C. Liquefied gases are returned to source tanks. In the second stage of separation, argon and sulphur hexafluoride, the residual gases, are concentrated by settling due to density difference. SF 6 is stored for recovery by condensation at high pressure while argon is further purified by thermal cracking of crossover impurities at 1000 deg. C followed by wet scrubbing.

Petroleum recovery process utilizing formaldehyde-sulfite-reacted polyacrylamide

Energy Technology Data Exchange (ETDEWEB)

Norton, C.J.; Falk, D.O.

1973-09-25

Micellar slugs followed by thickened water floods were injected into Berea cores (20.4 percent porosity, 398.4 md permeability, see Patent 3,692,113 for pretreatment) for enhanced oil recovery. About 61.1 percent residual oil was produced when the polymer in the thickened water was sulfomethylated hydrolyzed polyacrylamide. However, use of the conventional unhydrolyzed polyacrylamide recovered only 27.7 percent residual oil.

Utilities' nuclear fuel economic evaluation methods

International Nuclear Information System (INIS)

Sonz, L.A.

1987-01-01

This paper presents the typical perceptions, methods, considerations, and procedures used by an operating electric utility in the economic evaluation of nuclear fuel preparation and utilization scenarios. The means given are probably not an exclusive review of those available, but are the author's recollection of systems employed to select and recommend preferable courses of action. Economic evaluation of proposed nuclear fuel scenarios is an important, but not exclusive, means of deciding on corporate action. If the economic evaluation is performed and coordinated with the other corporate considerations, such as technical and operational ability, electrical system operations management, tax effects, capital management, rates impact, etc., then the resultant recommendation may be employed to the benefit of the customers and, consequently, to the corporation

Disintegration-wave method of recovery of industrial waste iron and steel industry enterprises

Directory of Open Access Journals (Sweden)

M. A. Vasechkin

2016-01-01

Full Text Available Rational use of raw materials and waste is one of the most important factors determining the effectiveness of any processing enterprise. Industrial wastes of mining and metallurgical industries are a valuable source of many elements. However, little activity of the mineral and inconsistent chemical and phase composition of the waste reduce their attractiveness for use as a secondary raw material, and the presence of heavy metals and water-soluble compounds is a serious environmental threat. Fractional excretion of elements that make up the slag can be carried out with the help of their recovery by disintegration-wave method. The paper presents a machine-hardware circuits for the implementation of recovery process of slag and disintegrator design. In conducting research on the example of slag samples of the enterprises in Stavropol and Krasnoyarsk territories, it was found out that the observed enrichment of slags on the composition of iron takes place, its physical and chemical activity increases and persists for a long period of time. These facts were noted in the study of the microstructure and the results of spectral analysis of the initial slags and subjected to recovery by disintegration-wave method. The results analysis led to the conclusion about the possibility of waste recovery of mining and metallurgical industries with by disintegration-wave method. Resulting in the processing materials with enhanced activity of the mineral part and certain chemical and phase composition, can be used as raw material for the production of metallurgical, cement and other industries.

Downhole fluid injection systems, CO2 sequestration methods, and hydrocarbon material recovery methods

Science.gov (United States)

Schaef, Herbert T.; McGrail, B. Peter

2015-07-28

Downhole fluid injection systems are provided that can include a first well extending into a geological formation, and a fluid injector assembly located within the well. The fluid injector assembly can be configured to inject a liquid CO2/H2O-emulsion into the surrounding geological formation. CO2 sequestration methods are provided that can include exposing a geological formation to a liquid CO2/H2O-emulsion to sequester at least a portion of the CO2 from the emulsion within the formation. Hydrocarbon material recovery methods are provided that can include exposing a liquid CO2/H2O-emulsion to a geological formation having the hydrocarbon material therein. The methods can include recovering at least a portion of the hydrocarbon material from the formation.

Filter forensics: microbiota recovery from residential HVAC filters.

Science.gov (United States)

Maestre, Juan P; Jennings, Wiley; Wylie, Dennis; Horner, Sharon D; Siegel, Jeffrey; Kinney, Kerry A

2018-01-30

Establishing reliable methods for assessing the microbiome within the built environment is critical for understanding the impact of biological exposures on human health. High-throughput DNA sequencing of dust samples provides valuable insights into the microbiome present in human-occupied spaces. However, the effect that different sampling methods have on the microbial community recovered from dust samples is not well understood across sample types. Heating, ventilation, and air conditioning (HVAC) filters hold promise as long-term, spatially integrated, high volume samplers to characterize the airborne microbiome in homes and other climate-controlled spaces. In this study, the effect that dust recovery method (i.e., cut and elution, swabbing, or vacuuming) has on the microbial community structure, membership, and repeatability inferred by Illumina sequencing was evaluated. The results indicate that vacuum samples captured higher quantities of total, bacterial, and fungal DNA than swab or cut samples. Repeated swab and vacuum samples collected from the same filter were less variable than cut samples with respect to both quantitative DNA recovery and bacterial community structure. Vacuum samples captured substantially greater bacterial diversity than the other methods, whereas fungal diversity was similar across all three methods. Vacuum and swab samples of HVAC filter dust were repeatable and generally superior to cut samples. Nevertheless, the contribution of environmental and human sources to the bacterial and fungal communities recovered via each sampling method was generally consistent across the methods investigated. Dust recovery methodologies have been shown to affect the recovery, repeatability, structure, and membership of microbial communities recovered from dust samples in the built environment. The results of this study are directly applicable to indoor microbiota studies utilizing the filter forensics approach. More broadly, this study provides a

Application of a precipitation method for uranium recovery from abu-zaabal phosphoric acid plant, Egypt

International Nuclear Information System (INIS)

El-hazek, N.M.T.; Hussein, E.M.

1995-01-01

Current industrial recovery of uranium from 30% phosphoric acid-produced by the dihydrate process-is based on solvent extraction method. Uranium recovery from concentrated phosphoric acid (45-52% p o5 ) produced by evaporation of the 30% acid or directly produced by the hemihydrate process, by solvent extraction is difficult to apply in practice. In addition to possible contamination of the acid by the organic solvents and/or their deterioration. This paper investigates the possibility of applying a precipitation method (Weterings and Janssen, 1985) for uranium recovery from both low (28% P 2 O 5 ) and high (48% P 2 O 5 ) concentration phosphoric acids produced by abu-zaabal phosphoric acid plant (Abuzaabal fertilizers and chemicals Co., Egypt). The 28% acid produced by H 2 SO 4 dihydrate method and the 48% acid produced by evaporation of the 28% acid The applied precipitation method depends on using NH 4 F as a uranium precipitant from both low and high concentration phosphoric acids in presence of acetone as a dispersing agent. All the relevant factors have been studied

The Train Driver Recovery Problem - Solution Method and Decision Support System Framework

DEFF Research Database (Denmark)

Rezanova, Natalia Jurjevna

2009-01-01

the proposed model and solution method is suitable for solving in real-time. Recovery duties are generated as resource constrained paths in duty networks, and the set partitioning problem is solved with a linear programming based branch-and-price algorithm. Dynamic column generation and problem space expansion...... driver decision support system in their operational environment. Besides solving a particular optimization problem, this thesis contributes with a description of the railway planning process, tactical crew scheduling and the real-time dispatching solutions, taking a starting point in DSB S....... Rezanova NJ, Ryan DM. The train driver recovery problem–A set partitioning based model and solution method. Computers and Operations Research, in press, 2009. doi: 10.1016/j.cor.2009.03.023. 2. Clausen J, Larsen A, Larsen J, Rezanova NJ. Disruption management in the airline industry–Concepts, models...

Play-level distributions of estimates of recovery factors for a miscible carbon dioxide enhanced oil recovery method used in oil reservoirs in the conterminous United States

Science.gov (United States)

Attanasi, E.D.; Freeman, P.A.

2016-03-02

In a U.S. Geological Survey (USGS) study, recovery-factor estimates were calculated by using a publicly available reservoir simulator (CO2 Prophet) to estimate how much oil might be recovered with the application of a miscible carbon dioxide (CO2) enhanced oil recovery (EOR) method to technically screened oil reservoirs located in onshore and State offshore areas in the conterminous United States. A recovery factor represents the percentage of an oil reservoir’s original oil in place estimated to be recoverable by the application of a miscible CO2-EOR method. The USGS estimates were calculated for 2,018 clastic and 1,681 carbonate candidate reservoirs in the “Significant Oil and Gas Fields of the United States Database” prepared by Nehring Associates, Inc. (2012).

Law No. 293 of 10 Jun. 1981 about utilization of the Danish underground

Energy Technology Data Exchange (ETDEWEB)

1981-06-10

The law provides the purposeful use and utilization of the Danish underground and its natural resources. The law applies to prospecting, exploration and recovery of resources which had not been economically utilized by private enterprise prior to 23 Febr. 1932. The underground can be utilized as storage place or for other purposes besides recovery. Recovery and research apply as well to the continental Danish shelf. Detailed rules to follow in underground exploration and utilization are precised.

ISS Contingency Attitude Control Recovery Method for Loss of Automatic Thruster Control

Science.gov (United States)

Bedrossian, Nazareth; Bhatt, Sagar; Alaniz, Abran; McCants, Edward; Nguyen, Louis; Chamitoff, Greg

2008-01-01

In this paper, the attitude control issues associated with International Space Station (ISS) loss of automatic thruster control capability are discussed and methods for attitude control recovery are presented. This scenario was experienced recently during Shuttle mission STS-117 and ISS Stage 13A in June 2007 when the Russian GN&C computers, which command the ISS thrusters, failed. Without automatic propulsive attitude control, the ISS would not be able to regain attitude control after the Orbiter undocked. The core issues associated with recovering long-term attitude control using CMGs are described as well as the systems engineering analysis to identify recovery options. It is shown that the recovery method can be separated into a procedure for rate damping to a safe harbor gravity gradient stable orientation and a capability to maneuver the vehicle to the necessary initial conditions for long term attitude hold. A manual control option using Soyuz and Progress vehicle thrusters is investigated for rate damping and maneuvers. The issues with implementing such an option are presented and the key issue of closed-loop stability is addressed. A new non-propulsive alternative to thruster control, Zero Propellant Maneuver (ZPM) attitude control method is introduced and its rate damping and maneuver performance evaluated. It is shown that ZPM can meet the tight attitude and rate error tolerances needed for long term attitude control. A combination of manual thruster rate damping to a safe harbor attitude followed by a ZPM to Stage long term attitude control orientation was selected by the Anomaly Resolution Team as the alternate attitude control method for such a contingency.

Barriers to utilization of modern methods of family planning amongst ...

African Journals Online (AJOL)

Barriers to utilization of modern methods of family planning amongst women in a ... is recognized by the world health organization (WHO) as a universal human right. ... Conclusion: The study finds numerous barriers to utilization of family ...

Investigation of Multiscale and Multiphase Flow, Transport and Reaction in Heavy Oil Recovery Process

Energy Technology Data Exchange (ETDEWEB)

Yortsos, Yanis C.; Akkutlu, Yucel; Amilik, Pouya; Kechagia, Persefoni; Lu, Chuan; Shariati, Maryam; Tsimpanogiannis, Ioannis; Zhan, Lang

2000-01-19

The emphasis of this work was on investigating the mechanisms and factors that control the recovery of heavy oil, with the objective to improve recovery efficiencies. For this purpose, the interaction of flow, transport and reaction at various scales (from the pore-network to the field scales) were studied. Particular mechanisms investigated included the onset of gas flow in foamy oil production and in in-situ steam drive, gravity drainage in steam process, the development of sustained combustion fronts and the propagation of foams in porous media. Analytical, computational and experimental methods were utilized to advance the state of the art in heavy oil recovery. Successful completion of this research was expected to lead to improvements in the recovery efficiency of various heavy oil processes.

Implementing recovery: an analysis of the key technologies in Scotland

Science.gov (United States)

2011-01-01

Background Over the past ten years the promotion of recovery has become a stated aim of mental health policies within a number of English speaking countries, including Scotland. Implementation of a recovery approach involves a significant reorientation of mental health services and practices, which often poses significant challenges for reformers. This article examines how four key technologies of recovery have assisted in the move towards the creation of a recovery-oriented mental health system in Scotland. Methods Drawing on documentary analysis and a series of interviews we examine the construction and implementation of four key recovery 'technologies' as they have been put to use in Scotland: recovery narratives, the Scottish Recovery Indicator (SRI), Wellness Recovery Action Planning (WRAP) and peer support. Results Our findings illuminate how each of these technologies works to instantiate, exemplify and disseminate a 'recovery orientation' at different sites within the mental health system in order to bring about a 'recovery oriented' mental health system. They also enable us to identify some of the factors that facilitate or hinder the effectiveness of those technologies in bringing about a change in how mental health services are delivered in Scotland. These finding provide a basis for some general reflections on the utility of 'recovery technologies' to implement a shift towards recovery in mental health services in Scotland and elsewhere. Conclusions Our analysis of this process within the Scottish context will be valuable for policy makers and service coordinators wishing to implement recovery values within their own national mental health systems. PMID:21569633

Implementing recovery: an analysis of the key technologies in Scotland

Directory of Open Access Journals (Sweden)

Sturdy Steve

2011-05-01

Full Text Available Abstract Background Over the past ten years the promotion of recovery has become a stated aim of mental health policies within a number of English speaking countries, including Scotland. Implementation of a recovery approach involves a significant reorientation of mental health services and practices, which often poses significant challenges for reformers. This article examines how four key technologies of recovery have assisted in the move towards the creation of a recovery-oriented mental health system in Scotland. Methods Drawing on documentary analysis and a series of interviews we examine the construction and implementation of four key recovery 'technologies' as they have been put to use in Scotland: recovery narratives, the Scottish Recovery Indicator (SRI, Wellness Recovery Action Planning (WRAP and peer support. Results Our findings illuminate how each of these technologies works to instantiate, exemplify and disseminate a 'recovery orientation' at different sites within the mental health system in order to bring about a 'recovery oriented' mental health system. They also enable us to identify some of the factors that facilitate or hinder the effectiveness of those technologies in bringing about a change in how mental health services are delivered in Scotland. These finding provide a basis for some general reflections on the utility of 'recovery technologies' to implement a shift towards recovery in mental health services in Scotland and elsewhere. Conclusions Our analysis of this process within the Scottish context will be valuable for policy makers and service coordinators wishing to implement recovery values within their own national mental health systems.

Optimizing delivery of recovery-oriented online self-management strategies for bipolar disorder: a review.

Science.gov (United States)

Leitan, Nuwan D; Michalak, Erin E; Berk, Lesley; Berk, Michael; Murray, Greg

2015-03-01

Self-management is emerging as a viable alternative to difficult-to-access psychosocial treatments for bipolar disorder (BD), and has particular relevance to recovery-related goals around empowerment and personal meaning. This review examines data and theory on BD self-management from a recovery-oriented perspective, with a particular focus on optimizing low-intensity delivery of self-management tools via the web. A critical evaluation of various literatures was undertaken. Literatures on recovery, online platforms, and self-management in mental health and BD are reviewed. The literature suggests that the self-management approach aligns with the recovery framework. However, studies have identified a number of potential barriers to the utilization of self-management programs for BD and it has been suggested that utilizing an online environment may be an effective way to surmount many of these barriers. Online self-management programs for BD are rapidly developing, and in parallel the recovery perspective is becoming the dominant paradigm for mental health services worldwide, so research is urgently required to assess the efficacy and safety of optimization methods such as professional and/or peer support, tailoring and the development of 'online communities'. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Quality of Recovery, Postdischarge Hospital Utilization, and 2-Year Functional Outcomes After an Outpatient Total Knee Arthroplasty Program.

Science.gov (United States)

Gauthier-Kwan, Olivier Y; Dobransky, Johanna S; Dervin, Geoffrey F

2018-02-05

Outpatient total knee arthroplasty (TKA) has been made possible with advances in perioperative care and standardized clinical inpatient pathways. While many studies report on benefits of outpatient programs, none explore patient-reported outcome measures. As such, our goals were to compare the short-term quality of recovery; highlight postdischarge hospital resources utilization; and report on 2-year functional outcomes scores. This was a prospective comparative cohort study of 43 inpatients (43 TKAs) and 43 outpatients (43 TKAs) operated on by a single surgeon between September 28, 2010 and May 5, 2015. All patients were given a diary to complete at 1, 3, 7, 14, and 28 days postoperatively; we collected 90-day complications, readmissions, and emergency department visits; Knee Injury and Osteoarthritis Outcome Score and Western Ontario and McMaster Universities Osteoarthritis Index scores were completed preoperatively and 2 years postoperatively. SPSS (IBM, version 22.0) was used for all statistical analyses. Quality of recovery (QoR-9) was similar in the outpatient TKA group compared with the inpatient group. No statistically significant differences were observed for Knee Injury and Osteoarthritis Outcome Score and Western Ontario and McMaster Universities Osteoarthritis Index subscores (P > .05). There was 1 readmission in both outpatient and inpatient groups. Six inpatients and 8 outpatients returned to the emergency department for any reason within 90 days, with no statistical significance observed between the 2 groups (P = .771). Outpatient TKA in selected patients produced similar short-term and 2-year patient-reported outcome measures and a comparable 90-day postdischarge hospital resource utilization when compared to an inpatient cohort, supporting further investigation into outpatient TKA. Copyright © 2018 Elsevier Inc. All rights reserved.

Recovery concept in a Norwegian setting to be examined by the assertive community treatment model and mixed methods.

Science.gov (United States)

Lofthus, Ann-Mari; Westerlund, Heidi; Bjørgen, Dagfinn; Lindstrøm, Jonas Christoffer; Lauveng, Arnhild; Rose, Diana; Ruud, Torleif; Heiervang, Kristin

2018-02-01

Recovery is a crucial concept in the mental health field. The research of recovery is split into the categories of personal, social and clinical recovery. The purpose of this study was to explore the fragmented concept of recovery in light of assertive community treatment (ACT) in Norway. The study has a mixed methods design with a pragmatic approach. The Questionnaire about the Process of Recovery and open-ended questions posed to 70 participants from 12 ACT teams in Norway, gathered by the "Users interview users" method, are combined with interviews or focus groups with eight of these participants. Surprisingly those under a community treatment order (CTO) report the highest degree of personal recovery. The qualitative material shows that the service users interpreted the concept of recovery differently than researchers and professionals. The ACT service users highlighted three important elements: flexible treatment, medication and access to a car. They emphasized the necessity for basic needs to be met in order to experience a meaningful recovery process, and these basic needs may be of even greater importance to those under CTOs. Their experiences should imply a greater emphasis on securing basic needs such as secure housing, sounder finances and access to the normal benefits offered by society. © 2016 Australian College of Mental Health Nurses Inc.

Research on Stochastic Resonance Signal’s Recovery

Directory of Open Access Journals (Sweden)

Hao Wang

2013-01-01

Full Text Available Using stochastic resonance to detect weak periodic signals has been widely used in various fields of science, which attracts much attention of researchers due to its advantages of revealing recessive periodic laws. This paper utilized this method to seek the underlying rule of setting weather index, so we can find that how to obtain the accurate expression of original periodic law by further investigation. This paper deals with the noise-contained signal restoring on the basis of the established system coupling the inversion system and bistable system. The simulation shows that this signal recovery method inversion effect is better and the application range is wider.

Interactions between Energy Efficiency Programs funded under the Recovery Act and Utility Customer-Funded Energy Efficiency Programs

Energy Technology Data Exchange (ETDEWEB)

Goldman, Charles A.; Stuart, Elizabeth; Hoffman, Ian; Fuller, Merrian C.; Billingsley, Megan A.

2011-02-25

Since the spring of 2009, billions of federal dollars have been allocated to state and local governments as grants for energy efficiency and renewable energy projects and programs. The scale of this American Reinvestment and Recovery Act (ARRA) funding, focused on 'shovel-ready' projects to create and retain jobs, is unprecedented. Thousands of newly funded players - cities, counties, states, and tribes - and thousands of programs and projects are entering the existing landscape of energy efficiency programs for the first time or expanding their reach. The nation's experience base with energy efficiency is growing enormously, fed by federal dollars and driven by broader objectives than saving energy alone. State and local officials made countless choices in developing portfolios of ARRA-funded energy efficiency programs and deciding how their programs would relate to existing efficiency programs funded by utility customers. Those choices are worth examining as bellwethers of a future world where there may be multiple program administrators and funding sources in many states. What are the opportunities and challenges of this new environment? What short- and long-term impacts will this large, infusion of funds have on utility customer-funded programs; for example, on infrastructure for delivering energy efficiency services or on customer willingness to invest in energy efficiency? To what extent has the attribution of energy savings been a critical issue, especially where administrators of utility customer-funded energy efficiency programs have performance or shareholder incentives? Do the new ARRA-funded energy efficiency programs provide insights on roles or activities that are particularly well-suited to state and local program administrators vs. administrators or implementers of utility customer-funded programs? The answers could have important implications for the future of U.S. energy efficiency. This report focuses on a selected set of ARRA

Fertilizer nitrogen prescription for cotton by 15N recovery method under integrated nutrient management using soil test crop response function

International Nuclear Information System (INIS)

Arulmozhiselvan, K.; Govindaswamy, M.; Chellamuthu, S.

2007-01-01

Fertilizer efficiency is a vital parameter in prescription functions to compute fertilizer requirements of crops for achieving a specific yield target. In Soil Test Crop Response (STCR) function, nitrogen fertilizer efficiency is calculated by Apparent N Recovery (ANR) method, which includes the effect of added N interaction (ANI) on soil N reserves. In order to exclude soil effect and refine STCR function, the real efficiency of fertilizer N was estimated by 15 N recovery method. By fitting 15 N recovery in the function, the fertilizer N required for a specific yield target of cotton was estimated. The estimated N requirement by 15 N recovery method was lesser than ANR method when available soil N relatively increased. The approach also fine-tuned the N contributing efficiency of soil, farmyard manure and Azospirillum under Integrated Nutrient Management (INM). For achieving 25 q of seed cotton yield in a soil having 220 kg of available N ha -1 , the predicted N requirement was 159 kg ha -1 under ANR method, whereas in 15 N recovery method fertilizer N to be applied was 138 kg ha -1 with urea alone and 79 kg ha -1 with urea + FYM + Azospirillum. (author)

Comparison between two braking control methods integrating energy recovery for a two-wheel front driven electric vehicle

International Nuclear Information System (INIS)

Itani, Khaled; De Bernardinis, Alexandre; Khatir, Zoubir; Jammal, Ahmad

2016-01-01

Highlights: • Comparison between two braking methods for an EV maximizing the energy recovery. • Wheels slip ratio control based on robust sliding mode and ECE R13 control methods. • Regenerative braking control strategy. • Energy recovery of a HESS with respect to road surface type and road condition. - Abstract: This paper presents the comparison between two braking methods for a two-wheel front driven Electric Vehicle maximizing the energy recovery on the Hybrid Energy Storage System. The first method consists in controlling the wheels slip ratio while braking using a robust sliding mode controller. The second method will be based on ECE R13H constraints for an M1 passenger vehicle. The vehicle model used for simulation is a simplified five degrees of freedom model. It is driven by two 30 kW permanent magnet synchronous motor (PMSM) recovering energy during braking phases. Several simulation results for extreme braking conditions will be performed and compared on various road type surfaces using Matlab/Simulink®. For an initial speed of 80 km/h, simulation results demonstrate that the difference of energy recovery efficiency between the two control braking methods is beneficial to the ECE constraints control method and it can vary from 3.7% for high friction road type to 11.2% for medium friction road type. At low friction road type, the difference attains 6.6% due to different reasons treated in the paper. The stability deceleration is also discussed and detailed.

Simulation Opportunity Index, A Simple and Effective Method to Boost the Hydrocarbon Recovery

KAUST Repository

Saputra, Wardana

2016-09-08

During periods of low oil prices, profitability of field developments drops drastically. To help with this difficulty, a cost-effective method has been proposed to boost the hydrocarbon recovery by optimizing well locations through the Simulated Opportunity Index (SOI). SOI is an intelligent method to identify zones with high potential for production which is empirically calculated from basic rock and fluid properties, and from reservoir pressure as its energy capacity. In order to obtain the best results, the original SOI formula (Molina et al., 2009) was extended to both oil and gas fields. Based on this modified SOI formula, a software program has been developed to locate the best well locations considering multilayer, existing wells, and fault existences. This paper describes how the SOI software helps as a simple, fast, and accurate way to obtain the higher hydrocarbon production than that of trial-error method and previous studies in two different fields located in offshore Indonesia. On one hand, the proposed method could save money by minimizing the required number of wells. On the other hand, it could maximize profit by maximizing recovery.

Methods of determining incremental energy costs for economic dispatch and inter-utility interchange in Canadian utilities

International Nuclear Information System (INIS)

El-Hawary, M.E.; El-Hawary, F.; Mbamalu, G.A.N.

1991-01-01

A questionnaire was mailed to ten Canadian utilities to determine the methods the utilities use in determining the incremental cost of delivering energy at any time. The questionnaire was divided into three parts: generation, transmission and general. The generation section dealt with heat rates, fuel, operation and maintenance, startup and shutdown, and method of prioritizing and economic evaluation of interchange transactions. Transmission dealt with inclusion of transmission system incremental maintenance costs, and transmission losses determination. The general section dealt with incremental costs aspects, and various other economic considerations. A summary is presented of responses to the questionnaire

Method of flash evaporation and condensation – heat pump for deep cooling of coal-fired power plant flue gas: Latent heat and water recovery

International Nuclear Information System (INIS)

Li, Yuzhong; Yan, Min; Zhang, Liqiang; Chen, Guifang; Cui, Lin; Song, Zhanlong; Chang, Jingcai; Ma, Chunyuan

2016-01-01

Highlights: • A method is developed for deep cooling of flue gas in coal-fired boilers. • The method can recover both latent heat and water from flue gas. • The method utilizes FGD scrubber as a deep cooling exchanger. • The method adopts the direct heat exchange mode to avoid the corrosion problem. - Abstract: Flue gas waste heat recovery and utilization is an efficient means to improve the energy efficiency of coal-fired power plants. At present, the surface corrosion and fouling problems of heat exchanger hinder the development of flue gas deep cooling. In this study, a novel flue gas deep cooling method that can reduce flue gas temperature below the dew point of vapor to recover latent heat and obtain clean water simultaneously is proposed to achieve improved energy efficiency. The heat transfer mode of this method is the direct contact mode, which takes the scrubber, e.g. the flue gas desulfurization (FGD) scrubber, as the deep cooling exchanger. The flash evaporation and condensation (FEC) device and heat pump (HP) are utilized to provide low-temperature medium, such as FGD slurry or water, for washing and deep cooling flue gas, to collect recovered water, and to absorb recovered waste heat. This method is called as the FEC–HP method. This paper elaborated on two optional models of the proposed method. The mechanism for recovering heat and water was also analyzed using the customized flue gas humidity chart, and the method to quantitate recovered heat and water, as well as the results of the case of a 300 MW coal-fired generator set were provided. Net present value calculations showed that this method is profitable in the scenario of burning high-water-content coals. Several potential advantages of this method and suggestions for practical application were also discussed.

Recovery efficiencies for Burkholderia thailandensis from various aerosol sampling media

Directory of Open Access Journals (Sweden)

Paul eDabisch

2012-06-01

Full Text Available Burkholderia thailandensis is used in the laboratory as a surrogate of the more virulent B. pseudomallei. Since inhalation is believed to be a natural route of infection for B. pseudomallei, many animal studies with B. pseudomallei and B. thailandensis utilize the inhalation route of exposure. The aim of the present study was to quantify the recovery efficiency of culturable B. thailandensis from several common aerosol sampling devices to ensure that collected microorganisms could be reliably recovered post-collection. The sampling devices tested included 25-mm gelatin filters, 25-mm stainless steel disks used in Mercer cascade impactors, and two types of glass impingers. The results demonstrate that while several processing methods tested resulted in significantly lower physical recovery efficiencies than other methods, it was possible to obtain culturable recovery efficiencies for B. thailandensis and physical recovery efficiencies for 1 μm fluorescent spheres of at least 0.95 from all of the sampling media tested given an appropriate sample processing procedure. The results of the present study also demonstrated that the bubbling action of liquid media in all-glass impingers (AGIs can result in physical loss of material from the collection medium, although additional studies are needed to verify the exact mechanisms involved. Overall, the results of this study demonstrate that the collection mechanism as well as the post-collection processing method can significantly affect the recovery from and retention of culturable microorganisms in sampling media, potentially affecting the calculated airborne concentration and any subsequent estimations of risk or dose derived from such data.

System and method for determining the net output torque from a waste heat recovery system

Science.gov (United States)

Tricaud, Christophe; Ernst, Timothy C.; Zigan, James A.

2016-12-13

The disclosure provides a waste heat recovery system with a system and method for calculation of the net output torque from the waste heat recovery system. The calculation uses inputs from existing pressure and speed sensors to create a virtual pump torque sensor and a virtual expander torque sensor, and uses these sensors to provide an accurate net torque output from the WHR system.

Analysis of recovery efficiency in high-temperature aquifer thermal energy storage: a Rayleigh-based method

Science.gov (United States)

Schout, Gilian; Drijver, Benno; Gutierrez-Neri, Mariene; Schotting, Ruud

2014-01-01

High-temperature aquifer thermal energy storage (HT-ATES) is an important technique for energy conservation. A controlling factor for the economic feasibility of HT-ATES is the recovery efficiency. Due to the effects of density-driven flow (free convection), HT-ATES systems applied in permeable aquifers typically have lower recovery efficiencies than conventional (low-temperature) ATES systems. For a reliable estimation of the recovery efficiency it is, therefore, important to take the effect of density-driven flow into account. A numerical evaluation of the prime factors influencing the recovery efficiency of HT-ATES systems is presented. Sensitivity runs evaluating the effects of aquifer properties, as well as operational variables, were performed to deduce the most important factors that control the recovery efficiency. A correlation was found between the dimensionless Rayleigh number (a measure of the relative strength of free convection) and the calculated recovery efficiencies. Based on a modified Rayleigh number, two simple analytical solutions are proposed to calculate the recovery efficiency, each one covering a different range of aquifer thicknesses. The analytical solutions accurately reproduce all numerically modeled scenarios with an average error of less than 3 %. The proposed method can be of practical use when considering or designing an HT-ATES system.

Distribution Agnostic Structured Sparsity Recovery: Algorithms and Applications

KAUST Repository

Masood, Mudassir

2015-05-01

Compressed sensing has been a very active area of research and several elegant algorithms have been developed for the recovery of sparse signals in the past few years. However, most of these algorithms are either computationally expensive or make some assumptions that are not suitable for all real world problems. Recently, focus has shifted to Bayesian-based approaches that are able to perform sparse signal recovery at much lower complexity while invoking constraint and/or a priori information about the data. While Bayesian approaches have their advantages, these methods must have access to a priori statistics. Usually, these statistics are unknown and are often difficult or even impossible to predict. An effective workaround is to assume a distribution which is typically considered to be Gaussian, as it makes many signal processing problems mathematically tractable. Seemingly attractive, this assumption necessitates the estimation of the associated parameters; which could be hard if not impossible. In the thesis, we focus on this aspect of Bayesian recovery and present a framework to address the challenges mentioned above. The proposed framework allows Bayesian recovery of sparse signals but at the same time is agnostic to the distribution of the unknown sparse signal components. The algorithms based on this framework are agnostic to signal statistics and utilize a priori statistics of additive noise and the sparsity rate of the signal, which are shown to be easily estimated from data if not available. In the thesis, we propose several algorithms based on this framework which utilize the structure present in signals for improved recovery. In addition to the algorithm that considers just the sparsity structure of sparse signals, tools that target additional structure of the sparsity recovery problem are proposed. These include several algorithms for a) block-sparse signal estimation, b) joint reconstruction of several common support sparse signals, and c

Utilization pattern of extension tools and methods by Agricultural Extension Agents

Directory of Open Access Journals (Sweden)

M Surudhi

2018-05-01

Full Text Available A study was conducted in Krishnagiri district of Tamil Nadu state to understand the utilization pattern of extension tools and methods by the agricultural extension agents. As ICT revolution is slowly conquering the rural sector, it becomes imperative that the agricultural extension agents transform themselves to the changing times and develop competencies in utilizing these ICTs.  The study explored the usage of various extension tools and methods by the change agents and the constraints faced in utilizing them. The findings revealed that the extension functionaries frequently used the individual contact methods viz., telephone, office calls and farm and home visits in the process of transfer of technology. Least efforts were shown in sending SMS based communication. Meetings were the common and frequently adopted group contact method. Demonstrations, farmer field school, farmer’s interest groups, field trips and farmer training programmes were moderately adopted. Posters, leaflets and pre-season campaigns were the widely adopted mass contact methods. They possess least skill in utilizing farm magazines, presenting television and radio programmes, which are among the most popular and most efficient mass contact methods. The extension functionaries need to be trained adequately on the wider use of electronic communication methods like e mails, and SMS in the local language. Efforts should be taken up to sensitize the importance and train the extension agents in the usage of different group and mass contact methods.

Sludge storage lagoon biogas recovery and use

Energy Technology Data Exchange (ETDEWEB)

Muller, D.; Norville, C. (Memphis and Shelby County Div. of Planning and Development, TN (United States))

1991-07-01

The City of Memphis has two wastewater treatment plants. The SWTP employs two large anaerobic digestion sludge lagoons as part of the overall sludge treatment system. Although these lagoons are effective in concentrating and digesting sludge, they can generate offensive odors. The SWTP uses aerobic digesters to partially stabilize the sludge and help reduce objectionable odors before it enters the lagoons. The anaerobic digestion of sludge in the lagoons results in the dispersion of a large quantity of biogas into the atmosphere. The City realized that if the lagoons could be covered, the odor problem could be resolved, and at the same, time, biogas could be recovered and utilized as a source of energy. In 1987, the City commissioned ADI International to conduct a feasibility study to evaluate alternative methods of covering the lagoons and recovering and utilizing the biogas. The study recommended that the project be developed in two phases: (1) recovery of the biogas and (2) utilization of the biogas. Phase 1 consists of covering the two lagoons with an insulated membrane to control odor and temperature and collect the biogas. Phase 1 was found to be economically feasible and offered a unique opportunity for the City to save substantial operating costs at the treatment facility. The Memphis biogas recovery project is the only application in the world where a membrane cover has been used on a municipal wastewater sludge lagoon. It is also the largest lagoon cover system in the world.

Investigation of Multiscale and Multiphase Flow, Transport and Reaction in Heavy Oil Recovery Processes; SEMIANNUAL

International Nuclear Information System (INIS)

Yorstos, Yanis C.

2002-01-01

The emphasis of this work was on investigating the mechanisms and factors that control the recovery of heavy oil with the objective to improve recovery efficiencies. For this purpose the interaction of flow transport and reaction at various scales from the pore network to the field scales were studied. Particular mechanisms to be investigated included the onset of gas flow in foamy oil production and in in-situ steam drive, gravity drainage in steam processes, the development of sustained combustion fronts and the propagation of foams in porous media. Analytical, computational and experimental methods were utilized to advance the state of the art in heavy oil recovery. Successful completion of this research was expected to lead to improvements in the Recovery efficiency of various heavy oil processes

Geothermal waste heat utilization from in situ thermal bitumen recovery operations.

Science.gov (United States)

Nakevska, Nevenka; Schincariol, Robert A; Dehkordi, S Emad; Cheadle, Burns A

2015-01-01

In situ thermal methods for bitumen extraction introduce a tremendous amount of energy into the reservoirs raising ambient temperatures of 13 °C to as high as 200 °C at the steam chamber edge and 50 °C along the reservoir edge. In essence these operations have unintentionally acted as underground thermal energy storage systems which can be recovered after completion of bitumen extraction activities. Groundwater flow and heat transport models of the Cold Lake, Alberta, reservoir, coupled with a borehole heat exchanger (BHE) model, allowed for investigating the use of closed-loop geothermal systems for energy recovery. Three types of BHEs (single U-tube, double U-tube, coaxial) were tested and analyzed by comparing outlet temperatures and corresponding heat extraction rates. Initial one year continuous operation simulations show that the double U-tube configuration had the best performance producing an average temperature difference of 5.7 °C, and an average heat extraction of 41 W/m. Given the top of the reservoir is at a depth of 400 m, polyethylene piping provided for larger extraction gains over more thermally conductive steel piping. Thirty year operation simulations illustrate that allowing 6 month cyclic recovery periods only increases the loop temperature gain by a factor of 1.2 over continuous operation. Due to the wide spacing of existing boreholes and reservoir depth, only a small fraction of the energy is efficiently recovered. Drilling additional boreholes between existing wells would increase energy extraction. In areas with shallower bitumen deposits such as the Athabasca region, i.e. 65 to 115 m deep, BHE efficiencies should be larger. © 2014, National Ground Water Association.

Surge recovery techniques for the Tevatron cold compressors

International Nuclear Information System (INIS)

Martinez, A.; Klebaner, A.L.; Makara, J.N.; Theilacker, J.C.; Fermilab

2006-01-01

The Fermilab Tevatron cryogenic system utilizes high-speed centrifugal cold compressors, made by Ishikawajima-Harima Heavy Industries Co. Ltd. (IHI), for high-energy operations [1]. The compressor is designed to pump 60 g/s of 3.6 K saturated helium vapor at a pressure ratio of 2.8, with an off-design range of 40 to 70 g/s and operating speeds between 40 and 95 krpm. Since initial commissioning in 1993, Tevatron transient conditions such as quench recovery have led to multiple-location machine trips as a result of the cold compressors entering the surge regime. Historically, compressors operating at lower inlet pressures and higher speeds have been especially susceptible to these machine trips and it was not uncommon to have multiple compressor trips during large multiple-house quenches. In order to cope with these events and limit accelerator down time, surge recovery techniques have been implemented in an attempt to prevent the compressors from tripping once the machine entered this surge regime. This paper discusses the different methods of surge recovery that have been employed. Data from tests performed at the Cryogenic Test Facility at Fermilab as well as actual Tevatron operational data were utilized. In order to aid in the determination of the surge region, a full mapping study was undertaken to characterize the entire pressure field of the cold compressor. These techniques were then implemented and tested at several locations in the Tevatron with some success

Evaluation of a Residential Mental Health Recovery Service in North Queensland

Directory of Open Access Journals (Sweden)

Marion Heyeres

2018-05-01

Full Text Available BackgroundEvidence shows that subacute mental health recovery occurs best when a person remains active within the community and fulfils meaningful and satisfying roles of their choosing. Several residential care services that incorporate these values have been established in Australia and overseas.AimsThis study describes (a the development of an evaluation framework for a new subacute residential mental health recovery service in regional Australia and (b reports on the formative evaluation outcomes.MethodsContinuous quality improvement and participatory research approaches informed all stages of the development of the evaluation framework. A program logic was established and subsequently tested for practicability. The resultant logic utilizes the Scottish Recovery Indicator 2 (SRI 2 service development tool, Individual Recovery Plans (IRPs, and the impact assessment of the service on psychiatric inpatient admissions (reported separately.ResultsService strengths included a recovery-focused practice that identifies and addresses the basic needs of residents (consumers. The consumers of the service were encouraged to develop their own goals and self-manage their recovery plans. The staff of the service were identified as working effectively in the context of the recovery process; the staff were seen as supported and valued. Areas for improvement included more opportunities for self-management for residents and more feedback from residents and carers.

Tenth oil recovery conference

International Nuclear Information System (INIS)

Sleeper, R.

1993-01-01

The Tertiary Oil Recovery Project is sponsored by the State of Kansas to introduce Kansas producers to the economic potential of enhanced recovery methods for Kansas fields. Specific objectives include estimation of the state-wide tertiary oil resource, identification and evaluation of the most applicable processes, dissemination of technical information to producers, occasional collaboration on recovery projects, laboratory studies on Kansas applicable processes, and training of students and operators in tertiary oil recovery methods. Papers have been processed separately for inclusion on the data base

Establishing a recovery orientation in mental health services: Evaluating the Recovery Self-Assessment (RSA) in a Swedish context.

Science.gov (United States)

Rosenberg, David; Svedberg, Petra; Schön, Ulla-Karin

2015-12-01

Although there has been an emphasis on developing knowledge regarding recovery in Sweden, it is unclear to what extent this has been translated into a recovery orientation in the provision of mental health services. Instruments, which present the components of recovery as measurable dimensions of change, may provide a framework for program development. Involving users is an essential factor in the utilization of such tools. The purpose of this study was to evaluate the psychometric properties of the Recovery Self-Assessment (RSA) measure and its potential for being utilized in a Swedish context. The sample consisted of 78 participants from 6 community mental health services targeting people with serious mental illnesses in a municipality in Sweden. They completed the RSA at the study baseline and two weeks later. User panels participated in the translation and administration of the RSA and the reporting of results. The Swedish version of the RSA had good face and content validity, satisfactory internal consistency, and a moderate to good level of stability in test-retest reliability. The user panels contributed to establishing validity and as collaborators in the study. Establishing the RSA as a valid and reliable instrument with which to focus on the recovery orientation of services is a first step in beginning to study the types of interventions that may effect and contribute to recovery oriented practice in Sweden. (c) 2015 APA, all rights reserved).

From recovery values to recovery-oriented practice?

DEFF Research Database (Denmark)

Dalum, Helle; Pedersen, Inge Kryger; Cunningham, Harry

2015-01-01

Introduction: The recovery model has influenced mental health services and fostered new standards for best practice. However, knowledge about how mental health care professionals (HCPs) experience recoveryoriented programs is sparse. Aim/Question: This paper explores HCPs' experiences when...... facilitating a recovery-oriented rehabilitation program. The research question is howdo HCPs experience a change in their attitude and practicewhen applying recovery-oriented programs? Methods: This paper draws on semi-structured in-depth qualitative interviews conducted with 16 HCPs experienced...... in facilitating a recovery-oriented rehabilitation program in either the USA or Denmark. Results: Three themes emerged from the HCPs' reflections on changes in attitudes and practices: “Hopeful Attitude” captures a change in the HCPs' attitude toward a more positive view on the future for clients' living...

Techno-economic analysis and optimization of the heat recovery of utility boiler flue gas

International Nuclear Information System (INIS)

Xu, Gang; Huang, Shengwei; Yang, Yongping; Wu, Ying; Zhang, Kai; Xu, Cheng

2013-01-01

Highlights: • Four typical flue gas heat recovery schemes are quantitatively analyzed. • The analysis considers thermodynamic, heat transfer and hydrodynamics factors. • Techno-economic analysis and optimization design are carried out. • High-stage steam substitute scheme obtains better energy-saving effect. • Large heat transfer area and high flue gas resistances weaken overall performance. - Abstract: Coal-fired power plants in China consume nearly half of available coals, and the resulting CO 2 emissions cover over 40% of total national emissions. Therefore, reducing the energy expenditure of coal-fired power plants is of great significance to China’s energy security and greenhouse gas reduction programs. For coal-fired power plants, the temperature of a boiler’s exhaust gas reaches 120–150 °C or even higher. The thermal energy of boiler’s exhaust accounts for approximately 3–8% of the total energy of fuel input. Given these factors, we conducted a techno-economic analysis and optimization design of the heat recovery system using boiler exhaust gas. This research is conformed to the principles of thermodynamic, heat transfer, and hydrodynamics. Based on the data from an existing 1000 MW typical power generation unit in China, four typical flue gas heat recovery schemes are quantitatively analyzed from the thermodynamics perspective. The impacts of flue gas heat recovery on net work output and standard coal consumption rate of various schemes are performed. Furthermore, the transfer area of heat recovery exchanger and the draft fan work increment due to the flue gas pressure drop are analyzed. Finally, a techno-economic analysis of the heat recovery schemes is conducted, and some recommendations on optimization design parameters are proposed, with full consideration of various factors such as the decrease on fuel cost due to energy conservation as well as the investment cost of heat recovery retrofitting. The results revealed that, high

Stranded cost recovery in electricity market reforms in the US

International Nuclear Information System (INIS)

Woo, C.K.; Lloyd, D.; Karimov, R.; Tishler, A.

2003-01-01

An important element of an electricity market reform is stranded cost recovery. This paper explains the cause of stranded costs, describes four recovery mechanisms, evaluates these mechanisms using the criteria of recovery certainty, economic efficiency and equity, reviews the financial performance of 12 utilities in the US in connection to stranded cost recovery, and shows why the mechanism used in California has contributed to the reform failure in that state. (Author)

Fiscal 2000 project on measures for assisting and diffusing environmentally-friendly coal utilization system introduction. CMG recovery/utilization system joint demonstration project; 2000 nendo kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo chosa hokoku. CMG kaishu riyo system kyodo jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A CMG (coal mine gas) recovery/utilization system was designed, constructed, and then demonstrated at a model coal mining district in Liaoning Province for the purpose of contributing to the solution of energy and environment related problems in China. The recovery system demonstration test, aiming to improve on safety and productivity of coal mining and to supply recovered gas with stability, involved gas drainage test boring, mine sealing, sealed gas induction control, centralized gas monitoring, etc., which were carried out at the coal mine working face. A utilization system demonstration test was conducted, and CMG would continue to be supplied to the current users and CMG utilization would be started at the other 6 coal mines. For the supply of CMG to large-scale gas consuming areas, steel materials were manufactured and processed for spherical gas holders and denitrification facilities, gas holders were constructed, pipe lines were installed, and a provisional gas supply was carried out. For the transfer and diffusion of the technology, Chinese engineers were trained in Japan and Japanese engineers were dispatched to China. (NEDO)

Combined geophysical methods for mapping infiltration pathways at the Aurora Water Aquifer recharge and recovery site

Science.gov (United States)

Jasper, Cameron A.

Although aquifer recharge and recovery systems are a sustainable, decentralized, low cost, and low energy approach for the reclamation, treatment, and storage of post- treatment wastewater, they can suffer from poor infiltration rates and the development of a near-surface clogging layer within infiltration ponds. One such aquifer recharge and recovery system, the Aurora Water site in Colorado, U.S.A, functions at about 25% of its predicted capacity to recharge floodplain deposits by flooding infiltration ponds with post-treatment wastewater extracted from river bank aquifers along the South Platte River. The underwater self-potential method was developed to survey self-potential signals at the ground surface in a flooded infiltration pond for mapping infiltration pathways. A method for using heat as a groundwater tracer within the infiltration pond used an array of in situ high-resolution temperature sensing probes. Both relatively positive and negative underwater self-potential anomalies are consistent with observed recovery well pumping rates and specific discharge estimates from temperature data. Results from electrical resistivity tomography and electromagnetics surveys provide consistent electrical conductivity distributions associated with sediment textures. A lab method was developed for resistivity tests of near-surface sediment samples. Forward numerical modeling synthesizes the geophysical information to best match observed self- potential anomalies and provide permeability distributions, which is important for effective aquifer recharge and recovery system design, and optimization strategy development.

Authentication and recovery of medical diagnostic image using dual reversible digital watermarking.

Science.gov (United States)

Deng, Xiaohong; Chen, Zhigang; Zeng, Feng; Zhang, Yaoping; Mao, Yimin

2013-03-01

This paper proposes a new region-based tampering detection and recovering method that utilizes both reversible digital watermarking and quad-tree decomposition for medical diagnostic image's authentication. Firstly, the quad-tree decomposition is used to divide the original image into blocks with high homogeneity, and then we computer pixels' linear interpolation as each block's recovery feature. Secondly, these recovery features as the first layer watermarking information is embedded by using simple invertible integer transformation. In order to enhance the proposed method's security, the logistic chaotic map is exploited to choose each block's reference pixel. The second layer watermark comprises by the quad-tree information and essential parameters for extraction are embedded by LSB replacement. In the authentication phase, the embedded watermark is extracted and the source image is recovered, and the similar linear interpolation technique is utilized to get each block's feature. Therefore, the tampering detection and localization can be achieved through comparing the extracted feature with the recomputed one, and the extracted feature can be used to recover those tampered regions with high similarity to their original state. Experimental results show that, compared with previous similar existing scheme, the proposed method not only achieves high embedding capacity and good visual quality of marked and restored image, but also has more accuracy for tampering detection.

Simulation Opportunity Index, A Simple and Effective Method to Boost the Hydrocarbon Recovery

KAUST Repository

Saputra, Wardana

2016-01-01

This paper describes how the SOI software helps as a simple, fast, and accurate way to obtain the higher hydrocarbon production than that of trial-error method and previous studies in two different fields located in offshore Indonesia. On one hand, the proposed method could save money by minimizing the required number of wells. On the other hand, it could maximize profit by maximizing recovery.

Recovery of oil from underground drill sites

International Nuclear Information System (INIS)

Streeter, W.S.; Hutchinson, T.S.; Ameri, S.; Wasson, J.A.; Aminian, K.

1991-01-01

This paper reports that a significant quantity of oil is left in reservoirs after conventional oil recovery techniques have been applied. In West Virginia and Pennsylvania alone, this oil has been estimated at over 4.5 billion barrels (0.72 billion m 3 ). Conventional recovery methods are already being used when applicable. But a new recovery method is needed for use in reservoirs that have been abandoned. One alternative method for recovery of the residual oil is known as oil recovery from underground drill sites. This recovery technology is a combination of proven methods and equipment from the petroleum, mining, and civil construction industries. Underground oil recovery can be an economically viable method of producing oil. This has been shown in producing fields, field tests, and feasibility, studies. Faced with decreasing domestic oil production, the petroleum industry should give serious consideration to the use of oil recovery from underground drill sites as a safe, practical, and environmentally sensitive alternative method of producing oil from many reservoirs

Selective recovery of molybdenum from spent HDS catalyst using oxidative soda ash leach/carbon adsorption method

International Nuclear Information System (INIS)

Park, Kyung Ho; Mohapatra, D.; Reddy, B. Ramachandra

2006-01-01

The petroleum refining industry makes extensive use of hydroprocessing catalysts. These catalysts contain environmentally critical and economically valuable metals such as Mo, V, Ni and Co. In the present study, a simple hydrometallurgical processing of spent hydrodesulphurization (HDS) catalyst for the recovery of molybdenum using sodium carbonate and hydrogen peroxide mixture was investigated. Recovery of molybdenum was largely dependent on the concentrations of Na 2 CO 3 and H 2 O 2 in the reaction medium, which in turn controls the pH of leach liquor and the presence of Al and Ni as impurities. Under the optimum leaching conditions (40 g L -1 Na 2 CO 3 , 6 vol.% H 2 O 2 , room temperature, 1 h) about 85% recovery of Mo was achieved. The leach liquor was processed by the carbon adsorption method, which selectively adsorbs Mo at pH around 0.75. Desorption of Mo was selective at 15 vol.% NH 4 OH. With a single stage contact, it was found possible to achieve >99%, adsorption and desorption efficiency. Using this method, recovery of molybdenum as MoO 3 product of 99.4% purity was achieved

Hidden values in bauxite residue (red mud): Recovery of metals

Energy Technology Data Exchange (ETDEWEB)

Liu, Yanju; Naidu, Ravi, E-mail: ravi.naidu@unisa.edu.au

2014-12-15

Highlights: • Current iron recovery techniques using red mud are depicted. • Advantages and disadvantages exist in different recovering processes. • Economic and environmental friendly integrated usage of red mud is promising. - Abstract: Bauxite residue (red mud) is a hazardous waste generated from alumina refining industries. Unless managed properly, red mud poses significant risks to the local environment due to its extreme alkalinity and its potential impacts on surface and ground water quality. The ever-increasing generation of red mud poses significant challenges to the aluminium industries from management perspectives given the low proportion that are currently being utilized beneficially. Red mud, in most cases, contains elevated concentrations of iron in addition to aluminium, titanium, sodium and valuable rare earth elements. Given the scarcity of iron supply globally, the iron content of red mud has attracted increasing research interest. This paper presents a critical overview of the current techniques employed for iron recovery from red mud. Information on the recovery of other valuable metals is also reviewed to provide an insight into the full potential usage of red mud as an economic resource rather than a waste. Traditional hydrometallurgy and pyrometallurgy are being investigated continuously. However, in this review several new techniques are introduced that consider the process of iron recovery from red mud. An integrated process which can achieve multiple additional values from red mud is much preferred over the single process methods. The information provided here should help to improve the future management and utilization of red mud.

Hidden values in bauxite residue (red mud): Recovery of metals

International Nuclear Information System (INIS)

Liu, Yanju; Naidu, Ravi

2014-01-01

Highlights: • Current iron recovery techniques using red mud are depicted. • Advantages and disadvantages exist in different recovering processes. • Economic and environmental friendly integrated usage of red mud is promising. - Abstract: Bauxite residue (red mud) is a hazardous waste generated from alumina refining industries. Unless managed properly, red mud poses significant risks to the local environment due to its extreme alkalinity and its potential impacts on surface and ground water quality. The ever-increasing generation of red mud poses significant challenges to the aluminium industries from management perspectives given the low proportion that are currently being utilized beneficially. Red mud, in most cases, contains elevated concentrations of iron in addition to aluminium, titanium, sodium and valuable rare earth elements. Given the scarcity of iron supply globally, the iron content of red mud has attracted increasing research interest. This paper presents a critical overview of the current techniques employed for iron recovery from red mud. Information on the recovery of other valuable metals is also reviewed to provide an insight into the full potential usage of red mud as an economic resource rather than a waste. Traditional hydrometallurgy and pyrometallurgy are being investigated continuously. However, in this review several new techniques are introduced that consider the process of iron recovery from red mud. An integrated process which can achieve multiple additional values from red mud is much preferred over the single process methods. The information provided here should help to improve the future management and utilization of red mud

Tomatoes in oil recovery. [Plant waste additives improve yield

Energy Technology Data Exchange (ETDEWEB)

1981-01-01

The waste from processing tomato, squash and pepper stalks found unexpected use in recovery of oil. Even a negligible amount thereof in an aqueous solution pumped into an oil-bearing formation turned out to be sufficient to increase the yield. Substances of plant origin, which improve dramatically the oil-flushing properties of water, not only increase the recovery of oil, but reduce the volume of fluid to be pumped into the stratum. The staff of the Institute of Deep Oil and Gas Deposits of the Azerbaijan Academy of Sciences, who proved the technological and economical advantages of using the waste from plant processing, transmitted their findings to the oil workers of Baku. The scientists have concluded that there is a good raw material base in this republic for utilizing this method on oil-bearing formations.

Energy-neutral sustainable nutrient recovery incorporated with the wastewater purification process in an enlarged microbial nutrient recovery cell

Science.gov (United States)

Sun, Dongya; Gao, Yifan; Hou, Dianxun; Zuo, Kuichang; Chen, Xi; Liang, Peng; Zhang, Xiaoyuan; Ren, Zhiyong Jason; Huang, Xia

2018-04-01

Recovery of nutrient resources from the wastewater is now an inevitable strategy to maintain the supply of both nutrient and water for our huge population. While the intensive energy consumption in conventional nutrient recovery technologies still remained as the bottleneck towards the sustainable nutrient recycle. This study proposed an enlarged microbial nutrient recovery cell (EMNRC) which was powered by the energy contained in wastewater and achieved multi-cycle nutrient recovery incorporated with in situ wastewater treatment. With the optimal recovery solution of 3 g/L NaCl and the optimal volume ratio of wastewater to recovery solution of 10:1, >89% of phosphorus and >62% of ammonium nitrogen were recovered into struvite. An extremely low water input ratio of water. It was proved the EMNRC system was a promising technology which could utilize the chemical energy contained in wastewater itself and energy-neutrally recover nutrient during the continuous wastewater purification process.

Hidden values in bauxite residue (red mud): recovery of metals.

Science.gov (United States)

Liu, Yanju; Naidu, Ravi

2014-12-01

Bauxite residue (red mud) is a hazardous waste generated from alumina refining industries. Unless managed properly, red mud poses significant risks to the local environment due to its extreme alkalinity and its potential impacts on surface and ground water quality. The ever-increasing generation of red mud poses significant challenges to the aluminium industries from management perspectives given the low proportion that are currently being utilized beneficially. Red mud, in most cases, contains elevated concentrations of iron in addition to aluminium, titanium, sodium and valuable rare earth elements. Given the scarcity of iron supply globally, the iron content of red mud has attracted increasing research interest. This paper presents a critical overview of the current techniques employed for iron recovery from red mud. Information on the recovery of other valuable metals is also reviewed to provide an insight into the full potential usage of red mud as an economic resource rather than a waste. Traditional hydrometallurgy and pyrometallurgy are being investigated continuously. However, in this review several new techniques are introduced that consider the process of iron recovery from red mud. An integrated process which can achieve multiple additional values from red mud is much preferred over the single process methods. The information provided here should help to improve the future management and utilization of red mud. Copyright © 2014 Elsevier Ltd. All rights reserved.

30 CFR 819.13 - Auger mining: Coal recovery.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Auger mining: Coal recovery. 819.13 Section 819....13 Auger mining: Coal recovery. (a) Auger mining shall be conducted so as to maximize the utilization and conservation of the coal in accordance with § 816.59 of this chapter. (b) Auger mining shall be...

Effect of Early Intensive Care on Recovery From Whiplash-Associated Disorders: Results of a Population-Based Cohort Study.

Science.gov (United States)

Skillgate, Eva; Côté, Pierre; Cassidy, J David; Boyle, Eleanor; Carroll, Linda; Holm, Lena W

2016-05-01

To determine whether the results from previous research suggesting that early intensive health care delays recovery from whiplash-associated disorders (WADs) were confounded by expectations of recovery and whether the association between early health care intensity and time to recovery varies across patterns of health care. Population-based inception cohort. All adults (≥18y) injured in motor vehicle collisions who received treatment from a regulated health professional or reported their injuries to the single provincially administered motor vehicle insurer. Participants with WAD (N=5204). Self-report visits to physicians, chiropractors, physiotherapists, massage therapists, and other professionals during the first 42 days postcollision were used to define health care intensity. Not applicable. Self-perceived recovery. Individuals with high utilization health care had slower recovery independent of expectation of recovery and other confounders. Compared with individuals who reported low utilization of physician services, recovery was slower for those with high health care utilization, regardless of the type of profession. For instance, those with high physician (hazard rate ratio [HRR]=.56; 95% confidence interval [CI], .42-.75), physician and high physiotherapy utilization (HRR=.68; 95% CI, .61-.77), physician and high chiropractor utilization (HRR=.74; 95% CI, .64-.85), and physician and high massage therapy utilization (HRR=.78; 95% CI, .68-.90) had significantly slower recovery. Our study adds to the existing evidence that early intensive care is associated with slower recovery from WAD, independent of expectation of recovery. The results have policy implications and suggest that the optimal management of WADs focuses on reassurance and education instead of intensive care. Copyright © 2016 American Congress of Rehabilitation Medicine. Published by Elsevier Inc. All rights reserved.

Solar energy utilization by physical methods.

Science.gov (United States)

Wolf, M

1974-04-19

On the basis of the estimated contributions of these differing methods of the utilization of solar energy, their total energy delivery impact on the projected U.S. energy economy (9) can be evaluated (Fig. 5). Despite this late energy impact, the actual sales of solar energy utilization equipment will be significant at an early date. Potential sales in photovoltaic arrays alone could exceed $400 million by 1980, in order to meet the projected capacity buildup (10). Ultimately, the total energy utilization equipment industry should attain an annual sales volume of several tens of billion dollars in the United States, comparable to that of several other energy related industries. Varying amounts of technology development are required to assure the technical and economic feasibility of the different solar energy utilization methods. Several of these developments are far enough along that the paths can be analyzed from the present time to the time of demonstration of technical and economic feasibility, and from there to production and marketing readiness. After that point, a period of market introduction will follow, which will differ in duration according to the type of market addressed. It may be noted that the present rush to find relief from the current energy problem, or to be an early leader in entering a new market, can entail shortcuts in sound engineering practice, particularly in the areas of design for durability and easy maintenance, or of proper application engineering. The result can be loss of customer acceptance, as has been experienced in the past with various products, including solar water heaters. Since this could cause considerable delay in achieving the expected total energy impact, it will be important to spend adequate time at this stage for thorough development. Two other aspects are worth mentioning. The first is concerned with the economic impacts. Upon reflection on this point, one will observe that largescale solar energy utilization will

Combustion of used tires for energy recovery. Yozumi taiya shokyaku ni suru netsuriyo

Energy Technology Data Exchange (ETDEWEB)

Ishizawa, N. (Toyo Tire and Rubber Co. Ltd., Osaka (Japan))

1993-03-15

The recycled automobile tires in 1991 amounts to 87%, and the tires are used most effectively for heat generation. The utilization of tires for heat in Japan and in other countries are outlined, and a detailed report is made on the use of used tires as fuel at coal cogeneration plants in tire manufacturing plants. The 'utilization percent for heat' is steadily increasing among the recycling applications of used tires. Energy recovery by dry distillation method and by direct combustion method is discussed. The states of used tire utilization in America, West Germany, and Britain are introduced. A concrete example of utilization for heat of used tires at a tire manufacturing plant is shown. Used tires are chopped into chips, mixed and burned in a coal boiler, the generated steam is used as the heat source for private power generation, and the power is used as the power source for the plant. 15 refs., 5 figs., 7 tabs.

Methods of fabricating cermet materials and methods of utilizing same

Science.gov (United States)

Kong, Peter C.

2006-04-04

Methods of fabricating cermet materials and methods of utilizing the same such as in filtering particulate and gaseous pollutants from internal combustion engines having intermetallic and ceramic phases. The cermet material may be made from a transition metal aluminide phase and an aluminia phase. The mixture may be pressed to form a green compact body and then heated in a nitrogen-containing atmosphere so as to melt aluminum particles and form the cermet. Filler materials may be added to increase the porosity or tailor the catalytic properties of the cermet material. Additionally, the cermet material may be reinforced with fibers or screens. The cermet material may also be formed so as to pass an electrical current therethrough to heat the material during use.

Methods of producing cermet materials and methods of utilizing same

Science.gov (United States)

Kong, Peter C [Idaho Falls, ID

2008-12-30

Methods of fabricating cermet materials and methods of utilizing the same such as in filtering particulate and gaseous pollutants from internal combustion engines having intermetallic and ceramic phases. The cermet material may be made from a transition metal aluminide phase and an alumina phase. The mixture may be pressed to form a green compact body and then heated in a nitrogen-containing atmosphere so as to melt aluminum particles and form the cermet. Filler materials may be added to increase the porosity or tailor the catalytic properties of the cermet material. Additionally, the cermet material may be reinforced with fibers or screens. The cermet material may also be formed so as to pass an electrical current therethrough to heat the material during use.

Mobile vapor recovery and vapor scavenging unit

International Nuclear Information System (INIS)

Stokes, C.A.; Steppe, D.E.

1991-01-01

This patent describes a mobile anti- pollution apparatus, for the recovery of hydrocarbon emissions. It comprises a mobile platform upon which is mounted a vapor recovery unit for recovering vapors including light hydrocarbons, the vapor recovery unit having an inlet and an outlet end, the inlet end adapted for coupling to an external source of hydrocarbon vapor emissions to recover a portion of the vapors including light hydrocarbons emitted therefrom, and the outlet end adapted for connection to a means for conveying unrecovered vapors to a vapor scavenging unit, the vapor scavenging unit comprising an internal combustion engine adapted for utilizing light hydrocarbon in the unrecovered vapors exiting from the vapor recovery unit as supplemental fuel

Influence of recovery method and centrifugation on epididymal sperm from collared peccaries (Pecari tajacu Linnaeus, 1758).

Science.gov (United States)

Bezerra, José Artur Brilhante; da Silva, Andréia Maria; Peixoto, Gislayne Christianne Xavier; da Silva, Mariana de Araújo; Franco de Oliveira, Moacir; Silva, Alexandre Rodrigues

2014-05-01

In order to establish protocols for gamete recovery from accidentally killed wild animals, or to take advantage of those slaughtered by captive breeders, we assess the influence of two methods on the recovery of epididymal sperm from collared peccaries, and verify the effect of centrifugation on such gametes. Genitalia from nine animals were used. For each animal, one epididymis was processed by flotation and the other was processed by retrograde flushing, both using a buffered media based on Tris. Following recovery, sperm were evaluated for motility, vigor, viability, functional membrane integrity, and morphology. A 1-mL aliquot of each sample was centrifuged, the supernatant removed, and the pellet suspended and evaluated as fresh samples. The sperm characteristics did not differ between the samples collected by flotation or retrograde flushing (P methods was affected by centrifugation. In conclusion, epididymal sperm from collared peccaries can be efficiently collected through flotation or retrograde flushing, but not when either is followed by centrifugation.

A method for studying post-fledging survival rates using data from ringing recoveries

NARCIS (Netherlands)

Thomson, D.L.; Baillie, S.R.; Peach, W.J.

1999-01-01

We present a method for studying post-fledging survival rates from data on national ringing recoveries. The approach extends the classical two-age-class models of Brownie et al. (1985) to include a third age-class of birds ringed as nestlings. The models can incorporate age-class-specific and

An Inversion Recovery NMR Kinetics Experiment

OpenAIRE

Williams, Travis J.; Kershaw, Allan D.; Li, Vincent; Wu, Xinping

2011-01-01

A convenient laboratory experiment is described in which NMR magnetization transfer by inversion recovery is used to measure the kinetics and thermochemistry of amide bond rotation. The experiment utilizes Varian spectrometers with the VNMRJ 2.3 software, but can be easily adapted to any NMR platform. The procedures and sample data sets in this article will enable instructors to use inversion recovery as a laboratory activity in applied NMR classes and provide research students with a conveni...

New method for evaluating effective recovery time and single photoelectron response in silicon photomultipliers

Energy Technology Data Exchange (ETDEWEB)

Grodzicka, Martyna, E-mail: m.grodzicka@ncbj.gov.pl; Szczęśniak, Tomasz; Moszyński, Marek; Szawłowski, Marek; Grodzicki, Krystian

2015-05-21

The linearity of a silicon photomultiplier (SiPM) response depends on the number of APD cells and its effective recovery time and it is related to the intensity and duration of the detected light pulses. The aim of this study was to determine the effective recovery time on the basis of the measured SiPM response to light pulses of different durations. A closer analysis of the SiPM response to the light pulses shorter than the effective recovery time of APD cells led to a method for the evaluation of the single photoelectron response of the devices where the single photoelectron peak cannot be clearly measured. This is necessary in the evaluation of the number of fired APD cells (or the number of photoelectrons) in measurements with light pulses of various durations. Measurements were done with SiPMs manufactured by two companies: Hamamatsu and SensL.

Thermodynamic analysis of heat recovery steam generator in combined cycle power plant

Directory of Open Access Journals (Sweden)

Ravi Kumar Naradasu

2007-01-01

Full Text Available Combined cycle power plants play an important role in the present energy sector. The main challenge in designing a combined cycle power plant is proper utilization of gas turbine exhaust heat in the steam cycle in order to achieve optimum steam turbine output. Most of the combined cycle developers focused on the gas turbine output and neglected the role of the heat recovery steam generator which strongly affects the overall performance of the combined cycle power plant. The present paper is aimed at optimal utilization of the flue gas recovery heat with different heat recovery steam generator configurations of single pressure and dual pressure. The combined cycle efficiency with different heat recovery steam generator configurations have been analyzed parametrically by using first law and second law of thermodynamics. It is observed that in the dual cycle high pressure steam turbine pressure must be high and low pressure steam turbine pressure must be low for better heat recovery from heat recovery steam generator.

Centrifugal washing and recovery as an improved method for obtaining lignin precipitated from South African kraft mill black liquor

CSIR Research Space (South Africa)

Namane, M

2015-10-01

Full Text Available This study describes centrifugal recovery as an improved method for collection of lignin isolated from black liquor obtained from a South African kraft mill. Precipitation of lignin was achieved by utilising 6 M sulphuric acid. Recovery...

Novel Methods to Study Aphasia Recovery after Stroke

DEFF Research Database (Denmark)

Hartwigsen, Gesa; Siebner, Hartwig R

2013-01-01

summarize how noninvasive brain stimulation can be used to elucidate mechanisms of plasticity in language networks and enhance language recovery after stroke. We first outline some basic principles of transcranial magnetic stimulation (TMS) and transcranial direct current stimulation (tDCS). We then present...... evidence from studies in healthy volunteers for a causal role of the right hemisphere in different language functions. Finally, we review recent studies that used TMS or tDCS to promote language recovery after stroke. Most of these studies applied noninvasive brain stimulation over contralateral right...

Recovery of molybdenum in froth flotation

International Nuclear Information System (INIS)

Parlman, R.M.; Bresson, C.R.

1981-01-01

Beta-mercaptoethanol has been found to be an effective suppressant for such minerals as copper, iron and lead in a molybdenum sulfide ore froth flotation operation. The recovery process and a suppressant utilizing said compound are claimed

Utilization of protein-rich residues in biotechnological processes.

Science.gov (United States)

Pleissner, Daniel; Venus, Joachim

2016-03-01

A drawback of biotechnological processes, where microorganisms convert biomass constituents, such as starch, cellulose, hemicelluloses, lipids, and proteins, into wanted products, is the economic feasibility. Particularly the cost of nitrogen sources in biotechnological processes can make up a large fraction of total process expenses. To further develop the bioeconomy, it is of considerable interest to substitute cost-intensive by inexpensive nitrogen sources. The aim of this mini-review was to provide a comprehensive insight of utilization methods of protein-rich residues, such as fish waste, green biomass, hairs, and food waste. The methods described include (i) production of enzymes, (ii) recovery of bioactive compounds, and/or (iii) usage as nitrogen source for microorganisms in biotechnological processes. In this aspect, the utilization of protein-rich residues, which are conventionally considered as waste, allows the development of value-adding processes for the production of bioactive compounds, biomolecules, chemicals, and materials.

Measuring Post-transfusion Recovery and Survival of Red Blood Cells: Strengths and Weaknesses of Chromium-51 Labeling and Alternative Methods

Directory of Open Access Journals (Sweden)

Camille Roussel

2018-05-01

Full Text Available The proportion of transfused red blood cells (RBCs that remain in circulation is an important surrogate marker of transfusion efficacy and contributes to predict the potential benefit of a transfusion process. Over the last 50 years, most of the transfusion recovery data were generated by chromium-51 (51Cr-labeling studies and were predominantly performed to validate new storage systems and new processes to prepare RBC concentrates. As a consequence, our understanding of transfusion efficacy is strongly dependent on the strengths and weaknesses of 51Cr labeling in particular. Other methods such as antigen mismatch or biotin-based labeling can bring relevant information, for example, on the long-term survival of transfused RBC. These radioactivity-free methods can be used in patients including from vulnerable groups. We provide an overview of the methods used to measure transfusion recovery in humans, compare their strengths and weaknesses, and discuss their potential limitations. Also, based on our understanding of the spleen-specific filtration of damaged RBC and historical transfusion recovery data, we propose that RBC deformability and morphology are storage lesion markers that could become useful predictors of transfusion recovery. Transfusion recovery can and should be accurately explored by more than one method. Technical optimization and clarification of concepts is still needed in this important field of transfusion and physiology.

Methods for enhancing mapping of thermal fronts in oil recovery

Science.gov (United States)

Lee, D.O.; Montoya, P.C.; Wayland, J.R. Jr.

1984-03-30

A method for enhancing the resistivity contrasts of a thermal front in an oil recovery production field as measured by the controlled source audio frequency magnetotelluric (CSAMT) technique is disclosed. This method includes the steps of: (1) preparing a CSAMT-determined topological resistivity map of the production field; (2) introducing a solution of a dopant material into the production field at a concentration effective to alter the resistivity associated with the thermal front; said dopant material having a high cation exchange capacity which might be selected from the group consisting of montmorillonite, illite, and chlorite clays; said material being soluble in the conate water of the production field; (3) preparing a CSAMT-determined topological resistivity map of the production field while said dopant material is moving therethrough; and (4) mathematically comparing the maps from step (1) and step (3) to determine the location of the thermal front. This method is effective with the steam flood, fire flood and water flood techniques.

Method for controlling exhaust gas heat recovery systems in vehicles

Science.gov (United States)

Spohn, Brian L.; Claypole, George M.; Starr, Richard D

2013-06-11

A method of operating a vehicle including an engine, a transmission, an exhaust gas heat recovery (EGHR) heat exchanger, and an oil-to-water heat exchanger providing selective heat-exchange communication between the engine and transmission. The method includes controlling a two-way valve, which is configured to be set to one of an engine position and a transmission position. The engine position allows heat-exchange communication between the EGHR heat exchanger and the engine, but does not allow heat-exchange communication between the EGHR heat exchanger and the oil-to-water heat exchanger. The transmission position allows heat-exchange communication between the EGHR heat exchanger, the oil-to-water heat exchanger, and the engine. The method also includes monitoring an ambient air temperature and comparing the monitored ambient air temperature to a predetermined cold ambient temperature. If the monitored ambient air temperature is greater than the predetermined cold ambient temperature, the two-way valve is set to the transmission position.

Sludge storage lagoon biogas recovery and use. Volume 2

Energy Technology Data Exchange (ETDEWEB)

Muller, D.; Norville, C. [Memphis and Shelby County Div. of Planning and Development, TN (United States)

1991-07-01

The City of Memphis has two wastewater treatment plants. The SWTP employs two large anaerobic digestion sludge lagoons as part of the overall sludge treatment system. Although these lagoons are effective in concentrating and digesting sludge, they can generate offensive odors. The SWTP uses aerobic digesters to partially stabilize the sludge and help reduce objectionable odors before it enters the lagoons. The anaerobic digestion of sludge in the lagoons results in the dispersion of a large quantity of biogas into the atmosphere. The City realized that if the lagoons could be covered, the odor problem could be resolved, and at the same, time, biogas could be recovered and utilized as a source of energy. In 1987, the City commissioned ADI International to conduct a feasibility study to evaluate alternative methods of covering the lagoons and recovering and utilizing the biogas. The study recommended that the project be developed in two phases: (1) recovery of the biogas and (2) utilization of the biogas. Phase 1 consists of covering the two lagoons with an insulated membrane to control odor and temperature and collect the biogas. Phase 1 was found to be economically feasible and offered a unique opportunity for the City to save substantial operating costs at the treatment facility. The Memphis biogas recovery project is the only application in the world where a membrane cover has been used on a municipal wastewater sludge lagoon. It is also the largest lagoon cover system in the world.

Using LDPC Code Constraints to Aid Recovery of Symbol Timing

Science.gov (United States)

Jones, Christopher; Villasnor, John; Lee, Dong-U; Vales, Esteban

2008-01-01

A method of utilizing information available in the constraints imposed by a low-density parity-check (LDPC) code has been proposed as a means of aiding the recovery of symbol timing in the reception of a binary-phase-shift-keying (BPSK) signal representing such a code in the presence of noise, timing error, and/or Doppler shift between the transmitter and the receiver. This method and the receiver architecture in which it would be implemented belong to a class of timing-recovery methods and corresponding receiver architectures characterized as pilotless in that they do not require transmission and reception of pilot signals. Acquisition and tracking of a signal of the type described above have traditionally been performed upstream of, and independently of, decoding and have typically involved utilization of a phase-locked loop (PLL). However, the LDPC decoding process, which is iterative, provides information that can be fed back to the timing-recovery receiver circuits to improve performance significantly over that attainable in the absence of such feedback. Prior methods of coupling LDPC decoding with timing recovery had focused on the use of output code words produced as the iterations progress. In contrast, in the present method, one exploits the information available from the metrics computed for the constraint nodes of an LDPC code during the decoding process. In addition, the method involves the use of a waveform model that captures, better than do the waveform models of the prior methods, distortions introduced by receiver timing errors and transmitter/ receiver motions. An LDPC code is commonly represented by use of a bipartite graph containing two sets of nodes. In the graph corresponding to an (n,k) code, the n variable nodes correspond to the code word symbols and the n-k constraint nodes represent the constraints that the code places on the variable nodes in order for them to form a valid code word. The decoding procedure involves iterative computation

Lessons from comparative effectiveness research methods development projects funded under the Recovery Act.

Science.gov (United States)

Zurovac, Jelena; Esposito, Dominick

2014-11-01

The American Recovery and Reinvestment Act of 2009 (ARRA) directed nearly US$29.2 million to comparative effectiveness research (CER) methods development. To help inform future CER methods investments, we describe the ARRA CER methods projects, identify barriers to this research and discuss the alignment of topics with published methods development priorities. We used several existing resources and held discussions with ARRA CER methods investigators. Although funded projects explored many identified priority topics, investigators noted that much work remains. For example, given the considerable investments in CER data infrastructure, the methods development field can benefit from additional efforts to educate researchers about the availability of new data sources and about how best to apply methods to match their research questions and data.

Decentralized method for utility regulation

Energy Technology Data Exchange (ETDEWEB)

Loeb, M. (North Carolina State Univ., Raleigh); Magat, W.A.

1979-10-01

A new institutional arrangement for regulating utilities is suggested that minimizes the costs of natural monopolies. A mixture of regulation and franchising, the plan draws on the advantages of each and eliminates many of the problems. The proposal allows utilities to set their own price on the basis of demand and marginal-cost projections. Subsidies are provided by the regulatory agency if there is a consumer surplus. The system encourages the utility to select a competitive price and to produce only the amount of service needed. Operating efficiency is encouraged by rewarding cost reductions and discouraging cost overstatement at the rate review. The regulatory agency would not need to take action to bring price and marginal costs into equality. The franchise sale can be made by competitive bidding, in which the bidders would capitalize part or all of the subsidy or the regulatory agency could recover the subsidy in a lump-sum tax on the utility.

AVATAR -- Adaptive Visualization Aid for Touring And Recovery

Energy Technology Data Exchange (ETDEWEB)

L. O. Hall; K. W. Bowyer; N. Chawla; T. Moore, Jr.; W. P. Kegelmeyer

2000-01-01

This document provides a report on the initial development of software which uses a standard visualization tool to determine, label and display salient regions in large 3D physics simulation datasets. This software uses parallel pattern recognition behind the scenes to handle the huge volume of data. This software is called AVATAR (Adaptive Visualization Aid for Touring and Recovery). It integrates approaches to gathering labeled training data, learning from large training sets utilizing parallelism and the final display of salient data in unseen visualization data sets. The paper uses vorticity fields for a large-eddy simulation to illustrate the method.

Method for aluminium dross utilization

International Nuclear Information System (INIS)

Lucheva, B.; Petkov, R.; Tzonev, Tz.

2003-01-01

A new hydrometallurgical method has been developed for metal aluminum utilization from secondary aluminum dross. Secondary aluminum dross is a powder product with an average of 35% aluminium content (below 1mm). It is waste from primary aluminum dross pyrometallurgical flux less treatment in rotary DC electric arc furnace. This method is based on aluminum leaching in copper chloride water solution. As a result an aluminum oxychloride solution and solids, consisting of copper and oxides are obtained. In order to copper chloride solution regenerate hydrochloric acid is added to the solids. The process is simple, quick, economic and safe. The aluminum oxychloride solution contains 56 g/l Al 2 O 3 . The molar ratios are Al:Cl=0,5; OH:Al=1. The solution has 32 % basicity and 1,1 g/cm 3 density. For increasing the molar ratio of aluminium to chlorine aluminum hydroxide is added to this solution at 80 o C. Aluminum hydroxide is the final product from the secondary aluminum dross alkaline leaching. As a result aluminum oxychloride solution of the following composition is prepared: Al 2 O 3 - 180 g/l; Al:Cl=1,88; OH:Al=4,64; basicity 82%; density 1,22 g/cm 3 , pH=4 -4,5. Aluminum oxychloride solution produced by means of this method can be used in potable and wastewater treatment, paper making, in refractory mixture as a binder etc. (Original)

Evaluation of a rapid method for recovery of norovirus and hepatitis A virus from oysters and blue mussels

DEFF Research Database (Denmark)

Uhrbrand, Katrine; Myrmel, Mette; Maunula, Leena

2010-01-01

Foodborne outbreaks caused by noroviruses (NoVs) and hepatitis A virus (HAV) are often linked to consumption of contaminated shellfish. The objective of this study was to identify an appropriate virus recovery method for real-time reverse transcriptase (RT)-PCR detection and subsequently to evalu......Foodborne outbreaks caused by noroviruses (NoVs) and hepatitis A virus (HAV) are often linked to consumption of contaminated shellfish. The objective of this study was to identify an appropriate virus recovery method for real-time reverse transcriptase (RT)-PCR detection and subsequently...

Gene expression profiles of mouse spermatogenesis during recovery from irradiation

DEFF Research Database (Denmark)

Shah, Fozia J; Tanaka, Masami; Nielsen, John E

2009-01-01

BACKGROUND: Irradiation or chemotherapy that suspend normal spermatogenesis is commonly used to treat various cancers. Fortunately, spermatogenesis in many cases can be restored after such treatments but knowledge is limited about the re-initiation process. Earlier studies have described the cell......BACKGROUND: Irradiation or chemotherapy that suspend normal spermatogenesis is commonly used to treat various cancers. Fortunately, spermatogenesis in many cases can be restored after such treatments but knowledge is limited about the re-initiation process. Earlier studies have described...... the cellular changes that happen during recovery from irradiation by means of histology. We have earlier generated gene expression profiles during induction of spermatogenesis in mouse postnatal developing testes and found a correlation between profiles and the expressing cell types. The aim of the present...... work was to utilize the link between expression profile and cell types to follow the cellular changes that occur during post-irradiation recovery of spermatogenesis in order to describe recovery by means of gene expression. METHODS: Adult mouse testes were subjected to irradiation with 1 Gy...

A method for seedling recovery in Jatropha curcas after cryogenic exposure of the seeds.

Science.gov (United States)

Silva, Rafael de C; Camillo, Julcéia; Scherwinski-Pereira, Jonny E

2012-03-01

Actually, the germplasm of Jatropha spp. is conserved as whole plants in field collections. Under this storage method, the genetic resources are exposed to disease, pest and natural hazards such as human error, drought and weather damage. Besides, field genebanks are costly to maintain and with important requirements of trained personnel. Thus, the development of efficient techniques to ensure its safe conservation and regeneration is therefore of paramount importance. In this work we describe a method for Jatropha curcas seeds cryoexposure and seedling recovery after thawed. In a first experiment, an efficient protocol for in vitro plant recovery was carried out using zygotic embryo or seeds with or without coat. In a second experiment, desiccated seeds with or without coat were exposed to liquid nitrogen and evaluated after cryoexposure. Germination percentages were variable among treatments, and seeds demonstrated tolerance to liquid nitrogen exposure under certain conditions. Seeds of J. curcas presented up to 99.6% germination after seed coat removal. Seeds with coat cultured in vitro did not germinate, and were 60% contaminated. The germination of the zygotic embryos was significantly higher in the 1/2 MS medium (93.1%) than in WPM medium (76.2%), but from zygotic embryo, abnormal seedlings reached up to 99%. Seeds with coat exposed to liquid nitrogen showed 60% germination in culture after coat removal with good plant growth, and seeds cryopreserved without coat presented 82% germination, but seedlings showed a reduced vigor and a significant increase in abnormal plants. Seeds cultured in vitro with coat did not germinate, independently of cryoexposure or not. This study reports the first successful in vitro seedling recovery methodology for Jatropha curcas seeds, after a cryopreservation treatment, and is recommended as an efficient procedure for in vitro plant recovery, when seeds are conserved in germplasm banks by low or cryotemperatures.

A method for seedling recovery in Jatropha curcas after cryogenic exposure of the seeds

Directory of Open Access Journals (Sweden)

Rafael de C. Silva

2012-03-01

Full Text Available Actually, the germplasm of Jatropha spp. is conserved as whole plants in field collections. Under this storage method, the genetic resources are exposed to disease, pest and natural hazards such as human error, drought and weather damage. Besides, field genebanks are costly to maintain and with important requirements of trained personnel. Thus, the development of efficient techniques to ensure its safe conservation and regeneration is therefore of paramount importance. In this work we describe a method for Jatropha curcas seeds cryoexposure and seedling recovery after thawed. In a first experiment, an efficient protocol for in vitro plant recovery was carried out using zygotic embryo or seeds with or without coat. In a second experiment, desiccated seeds with or without coat were exposed to liquid nitrogen and evaluated after cryoexposure. Germination percentages were variable among treatments, and seeds demonstrated tolerance to liquid nitrogen exposure under certain conditions. Seeds of J. curcas presented up to 99.6% germination after seed coat removal. Seeds with coat cultured in vitro did not germinate, and were 60% contaminated. The germination of the zygotic embryos was significantly higher in the ½ MS medium (93.1% than in WPM medium (76.2%, but from zygotic embryo, abnormal seedlings reached up to 99%. Seeds with coat exposed to liquid nitrogen showed 60% germination in culture after coat removal with good plant growth, and seeds cryopreserved without coat presented 82% germination, but seedlings showed a reduced vigor and a significant increase in abnormal plants. Seeds cultured in vitro with coat did not germinate, independently of cryoexposure or not. This study reports the first successful in vitro seedling recovery methodology for Jatropha curcas seeds, after a cryopreservation treatment, and is recommended as an efficient procedure for in vitro plant recovery, when seeds are conserved in germplasm banks by low or cryotemperatures.

Picturing recovery: a photovoice exploration of recovery dimensions among people with serious mental illness.

Science.gov (United States)

Cabassa, Leopoldo J; Nicasio, Andel; Whitley, Rob

2013-09-01

Recovery from mental disorders encompasses multiple interrelated dimensions. This study used photovoice to explore how individuals with serious mental illness and a history of substance abuse and homelessness envisioned their recovery. A dimensional recovery model was applied to examine how the interrelationships between recovery dimensions supported consumers' recovery journeys. Photovoice is a participatory research method that empowers people by giving them cameras to document their experiences and inform social action. Sixteen consumers recruited from two supported housing agencies participated in six weekly sessions to which they brought photographs that they took of persons and events in their lives that reflected recovery and wellness and discussed the meaning of the photographs in individual interviews and group sessions. The authors used pile-sorting, grounded theory, and a deductive template-analytic technique to analyze narrative and visual data. Spirituality, life achievements, and receiving and providing support were the most salient themes that emerged from the analysis and illustrate beneficial interrelationships between recovery dimensions. Participants discussed how they relied on their spirituality to support their sobriety and cope with addictions-aspects of clinical recovery. Educational and vocational achievements represented gains in functioning that contributed to increasing self-esteem and self-agency and reducing self-stigma. Social dimensions of recovery, such as receiving and giving support to loved ones, rippled through consumers' lives reducing isolation and enhancing their self-worth. The findings illustrate the value of participatory methods to understand what recovery signified to people with serious mental illness and how understanding the interrelationships between recovery dimensions can inform recovery-oriented services.

Recovery in aluminium

DEFF Research Database (Denmark)

Gundlach, Carsten

2006-01-01

In the present thesis the development of a unique experimental method for volume characterisation of individual embedded crystallites down to a radius of 150 nm is presented. This method is applied to in-situ studies of recovery in aluminium. The method is an extension of 3DXRD microscopy, an X...... are represented as strings. To identify the strings a combination of a 5D connected component type algorithm and multi-peak fitting was found to be superior. The first use of the method was a study of recovery of a deformed aluminium alloy (AA1050). The aluminium alloy was deformed by cold rolling to a thickness...

Acceptance and Avoidance Processes at Different Levels of Psychological Recovery from Enduring Mental Illness.

Science.gov (United States)

Siqueira, Vinicius R; Oades, Lindsay G

2015-01-01

Objective. This study examined the use of psychological acceptance and experiential avoidance, two key concepts of Acceptance and Commitment Therapy (ACT), in the psychological recovery process of people with enduring mental illness. Method. Sixty-seven participants were recruited from the metropolitan, regional, and rural areas of New South Wales, Australia. They all presented some form of chronic mental illness (at least 12 months) as reflected in DSM-IV Axis I diagnostic criteria. The Acceptance and Action Questionnaire (AAQ-19) was used to measure the presence of psychological acceptance and experiential avoidance; the Recovery Assessment Scale (RAS) was used to examine the levels of psychological recovery; and the Scales of Psychological Well-Being was used to observe if there are benefits in utilizing psychological acceptance and experiential avoidance in the recovery process. Results. An analysis of objectively quantifiable measures found no clear correlation between the use of psychological acceptance and recovery in mental illness as measured by the RAS. The data, however, showed a relationship between psychological acceptance and some components of recovery, thereby demonstrating its possible value in the recovery process. Conclusion. The major contribution of this research was the emerging correlation that was observed between psychological acceptance and positive levels of psychological well-being among individuals with mental illness.

Decision Support System for Aquifer Recharge (AR) and Aquifer Storage and Recovery (ASR) Planning, Design, and Evaluation - Principles and Technical Basis

Science.gov (United States)

Aquifer recharge (AR) is a technical method being utilized to enhance groundwater resources through man-made replenishment means, such as infiltration basins and injections wells. Aquifer storage and recovery (ASR) furthers the AR techniques by withdrawal of stored groundwater at...

Conservation genetics in the recovery of endangered animal species: a review of US endangered species recovery plans (1977-1998

Directory of Open Access Journals (Sweden)

Moyle, L. C.

2003-12-01

Full Text Available The utility of genetic data in conservation efforts, particularly in comparison to demographic information, is the subject of ongoing debate. Using a database of information surveyed from 181 US endangered and threatened species recovery plans, we addressed the following questions concerning the use of genetic information in animal recovery plans: I. What is the relative prominence of genetic vs. demographic data in recovery plan development? and, II. When are genetic factors viewed as a threat, and how do plans respond to genetic threats? In general, genetics appear to play a minor and relatively ill-defined part in the recovery planning process; demographic data are both more abundant and more requested in recovery plans, and tasks are more frequently assigned to the collection / monitoring of demographic rather than genetic information. Nonetheless, genetic threats to species persistence and recovery are identified in a substantial minority (22% of recovery plans, although there is little uniform response to these perceived threats in the form of specific proposed recovery or management tasks. Results indicate that better guidelines are needed to identify how and when genetic information is most useful for species recovery; we highlight specific contexts in which genetics may provide unique management information, beyond that provided by other kinds of data.

Comparison of methods for miRNA extraction from plasma and quantitative recovery of RNA from plasma and cerebrospinal fluid

Directory of Open Access Journals (Sweden)

Melissa A McAlexander

2013-05-01

Full Text Available Interest in extracellular RNA has intensified as evidence accumulates that these molecules may be useful as indicators of a wide variety of biological conditions. To establish specific extracellular RNA molecules as clinically relevant biomarkers, reproducible recovery from biological samples and reliable measurements of the isolated RNA are paramount. Towards these ends, careful and rigorous comparisons of technical procedures are needed at all steps from sample handling to RNA isolation to RNA measurement protocols. In the investigations described in this methods paper, RT-qPCR was used to examine the apparent recovery of specific endogenous miRNAs and a spiked-in synthetic RNA from blood plasma samples. RNA was isolated using several widely used RNA isolation kits, with or without the addition of glycogen as a carrier. Kits examined included total RNA isolation systems that have been commercially available for several years and commonly adapted for extraction of biofluid RNA, as well as more recently introduced biofluids-specific RNA methods. Our conclusions include the following: some RNA isolation methods appear to be superior to others for the recovery of RNA from biological fluids; addition of a carrier molecule seems to be beneficial for some but not all isolation methods; and partially or fully quantitative recovery of RNA is observed from increasing volumes of plasma and cerebrospinal fluid.

From heat integration targets toward implementation – A TSA (total site analysis)-based design approach for heat recovery systems in industrial clusters

International Nuclear Information System (INIS)

Hackl, Roman; Harvey, Simon

2015-01-01

The European process industry is facing major challenges to decrease production costs. One strategy to achieve this is by increasing energy efficiency. Single chemical processes are often well-integrated and the tools to target and design such measures are well developed. Site-wide heat integration based on total site analysis tools can be used to identify opportunities to further increase energy efficiency. However, the methodology has to be developed further in order to enable identification of practical heat integration measures in a systematic way. Designing site-wide heat recovery systems across an industrial cluster is complex and involves aspects apart from thermal process and utility flows. This work presents a method for designing a roadmap of heat integration investments based on total site analysis. The method is applied to a chemical cluster in Sweden. The results of the case study show that application of the proposed method can achieve up to 42% of the previously targeted hot utility savings of 129 MW. A roadmap of heat integration systems is suggested, ranging from less complex systems that achieve a minor share of the heat recovery potential to sophisticated, strongly interdependent systems demanding large investments and a high level of collaboration. - Highlights: • Methodology focused on the practical implementation of site-wide heat recovery. • Algorithm to determine a roadmap of heat integration investments. • Case study: 42% hot utility savings potential at a pay-back period of 3.9y.

Soot blowing methods and soot steam consumption in Swedish recovery boilers; Sotningsmetoder och sotaangfoerbrukning i svenska sodapannor

Energy Technology Data Exchange (ETDEWEB)

Svedin, Kristoffer; Wallin, Erik; Ahlroth, Mikael

2008-09-15

The aim with the report was to put together a description of the current state of the sootblowing systems at Swedish recovery boilers, and to explain differences in cleanability and sootblowing efficiency. In chapter 4 a summary of new techniques and alternative soot blowing methods is found. The report is intended for persons working in the pulp industry. To facilitate the benchmarking the recovery boilers have been divided into two groups. Group A comprises recovery boilers which only have one stop per year and the remaining recovery boilers with more than one stop are classified into group B. The following conclusions, based on the recovery boiler design specifications, are of importance to achieve high boiler availability: Low furnace load; High recovery boiler, wide furnace bottom area; Modern air ports; Small or no correlation between cross pitch division in heat surfaces and cleanability could be seen. The expectation was to identify such a relation. However there are doubts on the correctness in reported data. The amount of chlorine and potassium is assumed to affect the cleanability for a few recovery boilers, but for the majority the amounts are low and most likely do not impact the operation. Because of the large impact of the recovery boilers design data (furnace area, load etc.) on the sootblowing, it has been hard to identify the relation cleanability contra sootblowing system. The relations that could be seen are: No distinction between normally designed nozzles and 'high efficiency' nozzles could be identified. The operational conditions for the different models differ a lot and the effect of nozzle type could not be distinguished. Only a minority of the soot blowing sequences are known from the study. In the recovery boilers with problematic areas improvements can be made in the soot blowing sequence. Four recovery boilers are using intelligent soot blowing of some kind. Two of these boilers have low availability and the other two have

New filtration system for efficient recovery of waterborne Cryptosporidium oocysts and Giardia cysts

DEFF Research Database (Denmark)

Al-Sabi, Mohammad Nafi Solaiman; Gad, J. A.; Riber, Ulla

2015-01-01

-)cysts (1x10(2); 10 replicates) was successfully amplified using real-time PCR.ConclusionsThe use of a metallic filter, sonication and air backwash' were key factors for creating a highly efficient system for recovery of apparently undamaged protozoa.Significance and Impact of the StudyThis reagent......AimsTo develop a filtration unit for efficient recovery of waterborne Cryptosporidium oocysts and Giardia cysts ((oo-)cysts) in drinking water.Methods and ResultsThis unit utilizes a metallic filter and an ultrasound transducer for eluting (oo-)cysts, with a fixed retentate backwash volume; approx....... 400l. Changes in the viability was evaluated by seeding wild type (oo-)cysts (1x10(4)) followed by sonication for 5, 10, 20 or 40s (five replicates for each period). Flow cytometry analysis showed negligible increase in the mortality of (oo-)cysts exposed to 5-10s of sonication. Recovery rate...

Application of Biosurfactants Produced by Pseudomonas putida using Crude Palm Oil (CPO) as Substrate for Crude Oil Recovery using Batch Method

Science.gov (United States)

Suryanti, V.; Handayani, D. S.; Masykur, A.; Septyaningsih, I.

2018-03-01

The application of biosurfactants which have been produced by Pseudomonas putida in nutrient broth medium supplemented with NaCl and crude palm oil (CPO) for oil recovery has been evaluated. The crude and purified biosurfactants have been examined for oil recovery from a laboratory oil-contaminated sand in agitated flask (batch method). Two synthetic surfactants and water as control was also performed for oil recovery as comparisons. Using batch method, the results showed that removing ability of crude oil from the oil-contaminated sand by purified and crude biosurfactants were 79.40±3.10 and 46.84±2.23 %, respectively. On other hand, the recoveries obtained with the SDS, Triton X-100 and water were 94.33±0.47, 74.84±7.39 and 34.42±1.21%respectively.

Study on a heat recovery system for the thermal power plant utilizing air cooling island

International Nuclear Information System (INIS)

Sun, Jian; Fu, Lin; Sun, Fangtian; Zhang, Shigang

2014-01-01

A new heat recovery system for CHP (combined heat and power) systems named HRU (heat recovery unit) is presented, which could recover the low grade heat of exhausted steam from the turbine at the thermal power plant directly. Heat recovery of exhausted steam is often accomplished by recovering the heat of cooling water in current systems. Therefore, two processes of heat transfer is needed at least. However, exhausted steam could be condensed in the evaporator of HRU directly, which reduce one process of heat transfer. A special evaporator is designed condense the exhausted steam directly. Simulated results are compared to experiments, which could include the calculation of heat transfer coefficients of different parts of HRU. It is found that about 25Mw of exhausted steam is recovered by this system. HRU could be promising for conventional CHP systems, which could increase the total energy efficiency obviously and enlarge the heating capacity of a built CHP system. - Highlights: • A new heat recovery system for thermal power plant is presented. • A mathematical model including heat transfer coefficients calculation is given. • This heat recovery system is experimented at a thermal power plant. • Performances of this system under different working conditions are simulated

Development of partitioning method

International Nuclear Information System (INIS)

Kondo, Yasuo; Kubota, Masumitsu; Abe, Tadashi; Nagato, Kotaro.

1991-09-01

Spent fuels from nuclear power stations contain many useful elements, which can be utilized as heat and irradiation sources, radioisotope, elemental resource, etc. Their recovery from spent fuel and effective uses have the advantages in not only converting the radioactive waste to beneficial resources but also promoting rationalization of the management and disposal of the radioactive wastes. In present study, published literature related to recovery and utilization of useful elements in spent fuel was mainly surveyed, present states and trends in their research and development were analyzed, and their future prospects were conjectured. Research and development on recovery and utilization of useful elements are being continued mainly in USA, Europe and Japan. A transportable food irradiator with Cs-137 and an electric power source with Sr-90 for remote weather station are typical examples in major past applications. However, research and development on recovery and utilization are not so much active and the future efforts should be expected hereafter. Present study was conducted under the auspices of the Science and Technology Agency of Japan. (author)

Utilization of OR method toward realization of better fast breeder reactor cycle

International Nuclear Information System (INIS)

Shiotani, Hiroki

2008-01-01

Fast Reactor Cycle Technology Development (FaCT) Project was now started aiming at commercialization of new nuclear power plants system. In parallel with development of component technology and technology demonstration by test, development of comprehensive evaluation method of the FBR cycle system is under way and scenario study, discounted cash flow (DCF) method, analytic hierarchy process (AHP), real option, supply chain management (SCM) and others are used. Since commercialized FBR cycle would request long-term and large-scale development contributed by so many participants, modeling of nuclear system and knowledge management are beneficial even for development of evaluation method and further utilization of OR technology is highly expected. Comprehensive evaluation methods now utilized or developing were overlooked from the standpoint of OR, 'Science of Better'. (T. Tanaka)

Classification of methods and equipment recovery secondary waters

Directory of Open Access Journals (Sweden)

G. V. Kalashnikov

2017-01-01

Full Text Available The issues of purification of secondary waters of industrial production have an important place and are relevant in the environmental activities of all food and chemical industries. For cleaning the transporter-washing water of beet-sugar production the key role is played by the equipment of treatment plants. A wide variety of wastewater treatment equipment is classified according to various methods. Typical structures used are sedimentation tanks, hydrocyclones, separators, centrifuges. In turn, they have a different degree of purification, productivity through the incoming suspension and purified secondary water. This is equipment is divided into designs, depending on the range of particles to be removed. A general classification of methods for cleaning the transporter-washing water, as well as the corresponding equipment, is made. Based on the analysis of processes and instrumentation, the main methods of wastewater treatment are identified: mechanical, physicochemical, combined, biological and disinfection. To increase the degree of purification and reduce technical and economic costs, a combined method is widely used. The main task of the site for cleaning the transporter-washing waters of sugar beet production is to provide the enterprise with water in the required quantity and quality, with economical use of water resources, taking into account the absence of pollution of surface and groundwater by industrial wastewater. In the sugar industry is currently new types of washing equipment of foreign production are widely used, which require high quality and a large amount of purified transporter-washing water for normal operation. The proposed classification makes it possible to carry out a comparative technical and economic analysis when choosing the methods and equipment for recuperation of secondary waters. The main equipment secondary water recovery used at the beet-sugar plant is considered. The most common beet processing plant is a

Hydrometallurgical Recovery of Metal Values From Spent Dry Battery Cells

International Nuclear Information System (INIS)

Rabah, M.A.; Barakat, M.A.; Mahrous, Y.Sh.

1999-01-01

This study focuses on the recovery of metal values from spent dry battery cells (DBC) applying a hydro-pyrometallurgical method. A process flow sheet was followed up starting with cutting the DBC with toothed cutter disc followed by water soaking and rinsing. Water soluble ingredients were filtered. Solid residue was assorted with the help of magnetic separation and water flotation.The method utilizes hydrogen peroxide to enhance dissolution of these metals in acidic or alkaline leachants. Parameters affecting the recovery efficiency such as stoichiometric ratio, solid: liquid ratio, temperature, time and ph of the system were investigated. In this concern, experiments were executed with a battery sample weighing up to 15 kg. Atomic absorption analysis showed that the input DBC contain appreciable amounts of metal zinc, zinc chloride and manganese that are recoverable.Results obtained revealed that metallic parts, carbon rods and paper were safely separated for recycling. From the water-soluble salts, pure NH 4 CI, MnO 2 and ZnCI 2 salts are obtained meeting the standard specifications. Temperature up to 55 degree enhances the recovery process. Under the optimum conditions, maximum recovery efficiency obtained amounts to 93% for Mn, and 99.5% for Zn and NH 4 CI. A model for explaining the obtained results was also given. Dissolution of metals concerned increases in the order nitric> hydrochloric acid. Results were explained in the premise of the kinetic and thermodynamic properties of the reactions involved. Cost estimate of the products shows that the prices of the products are competitive to those of the market prices

Energy efficiency of substance and energy recovery of selected waste fractions

International Nuclear Information System (INIS)

Fricke, Klaus; Bahr, Tobias; Bidlingmaier, Werner; Springer, Christian

2011-01-01

In order to reduce the ecological impact of resource exploitation, the EU calls for sustainable options to increase the efficiency and productivity of the utilization of natural resources. This target can only be achieved by considering resource recovery from waste comprehensively. However, waste management measures have to be investigated critically and all aspects of substance-related recycling and energy recovery have to be carefully balanced. This article compares recovery methods for selected waste fractions with regard to their energy efficiency. Whether material recycling or energy recovery is the most energy efficient solution, is a question of particular relevance with regard to the following waste fractions: paper and cardboard, plastics and biowaste and also indirectly metals. For the described material categories material recycling has advantages compared to energy recovery. In accordance with the improved energy efficiency of substance opposed to energy recovery, substance-related recycling causes lower emissions of green house gases. For the fractions paper and cardboard, plastics, biowaste and metals it becomes apparent, that intensification of the separate collection systems in combination with a more intensive use of sorting technologies can increase the extent of material recycling. Collection and sorting systems must be coordinated. The objective of the overall system must be to achieve an optimum of the highest possible recovery rates in combination with a high quality of recyclables. The energy efficiency of substance related recycling of biowaste can be increased by intensifying the use of anaerobic technologies. In order to increase the energy efficiency of the overall system, the energy efficiencies of energy recovery plants must be increased so that the waste unsuitable for substance recycling is recycled or treated with the highest possible energy yield.

Design and evaluation of fluidized bed heat recovery for diesel engine systems

Science.gov (United States)

Hamm, J. R.; Newby, R. A.; Vidt, E. J.; Lippert, T. E.

1985-01-01

The potential of utilizing fluidized bed heat exchangers in place of conventional counter-flow heat exchangers for heat recovery from adiabatic diesel engine exhaust gas streams was studied. Fluidized bed heat recovery systems were evaluated in three different heavy duty transport applications: (1) heavy duty diesel truck; (2) diesel locomotives; and (3) diesel marine pushboat. The three applications are characterized by differences in overall power output and annual utilization. For each application, the exhaust gas source is a turbocharged-adiabatic diesel core. Representative subposed exhaust gas heat utilization power cycles were selected for conceptual design efforts including design layouts and performance estimates for the fluidized bed heat recovery heat exchangers. The selected power cycles were: organic rankine with RC-1 working fluid, turbocompound power turbine with steam injection, and stirling engine. Fuel economy improvement predictions are used in conjunction with capital cost estimates and fuel price data to determine payback times for the various cases.

Bayesian Recovery of Clipped OFDM Signals: A Receiver-based Approach

KAUST Repository

Al-Rabah, Abdullatif R.

2013-05-01

Recently, orthogonal frequency-division multiplexing (OFDM) has been adopted for high-speed wireless communications due to its robustness against multipath fading. However, one of the main fundamental drawbacks of OFDM systems is the high peak-to-average-power ratio (PAPR). Several techniques have been proposed for PAPR reduction. Most of these techniques require transmitter-based (pre-compensated) processing. On the other hand, receiver-based alternatives would save the power and reduce the transmitter complexity. By keeping this in mind, a possible approach is to limit the amplitude of the OFDM signal to a predetermined threshold and equivalently a sparse clipping signal is added. Then, estimating this clipping signal at the receiver to recover the original signal. In this work, we propose a Bayesian receiver-based low-complexity clipping signal recovery method for PAPR reduction. The method is able to i) effectively reduce the PAPR via simple clipping scheme at the transmitter side, ii) use Bayesian recovery algorithm to reconstruct the clipping signal at the receiver side by measuring part of subcarriers, iii) perform well in the absence of statistical information about the signal (e.g. clipping level) and the noise (e.g. noise variance), and at the same time iv is energy efficient due to its low complexity. Specifically, the proposed recovery technique is implemented in data-aided based. The data-aided method collects clipping information by measuring reliable 
data subcarriers, thus makes full use of spectrum for data transmission without the need for tone reservation. The study is extended further to discuss how to improve the recovery of the clipping signal utilizing some features of practical OFDM systems i.e., the oversampling and the presence of multiple receivers. Simulation results demonstrate the superiority of the proposed technique over other recovery algorithms. The overall objective is to show that the receiver-based Bayesian technique is highly

Comparison of direct and indirect methods of estimating health state utilities for resource allocation: review and empirical analysis.

Science.gov (United States)

Arnold, David; Girling, Alan; Stevens, Andrew; Lilford, Richard

2009-07-22

Utilities (values representing preferences) for healthcare priority setting are typically obtained indirectly by asking patients to fill in a quality of life questionnaire and then converting the results to a utility using population values. We compared such utilities with those obtained directly from patients or the public. Review of studies providing both a direct and indirect utility estimate. Papers reporting comparisons of utilities obtained directly (standard gamble or time tradeoff) or indirectly (European quality of life 5D [EQ-5D], short form 6D [SF-6D], or health utilities index [HUI]) from the same patient. PubMed and Tufts database of utilities. Sign test for paired comparisons between direct and indirect utilities; least squares regression to describe average relations between the different methods. Mean utility scores (or median if means unavailable) for each method, and differences in mean (median) scores between direct and indirect methods. We found 32 studies yielding 83 instances where direct and indirect methods could be compared for health states experienced by adults. The direct methods used were standard gamble in 57 cases and time trade off in 60(34 used both); the indirect methods were EQ-5D (67 cases), SF-6D (13), HUI-2 (5), and HUI-3 (37). Mean utility values were 0.81 (standard gamble) and 0.77 (time tradeoff) for the direct methods; for the indirect methods: 0.59(EQ-5D), 0.63 (SF-6D), 0.75 (HUI-2) and 0.68 (HUI-3). Direct methods of estimating utilities tend to result in higher health ratings than the more widely used indirect methods, and the difference can be substantial.Use of indirect methods could have important implications for decisions about resource allocation: for example, non-lifesaving treatments are relatively more favoured in comparison with lifesaving interventions than when using direct methods.

Utilities pull together to design latest storm management software

Energy Technology Data Exchange (ETDEWEB)

Wildman, T.; Ritchie, I.

2003-04-01

Development of Outage Mitigation and Recovery software by the Electric Power Research Institute with the support of cooperating electric utilities is discussed. The software is designed to aid utilities in their resource allocation and mutual assistance activities during recovery from major outages cause by natural or man-made disasters. The software is designed to operate in conjunction with major commercial outage systems, to add significant new functionality not available in existing systems. The new software module, called emPower, was actually developed by LeT Systems, a world leader in the design, development and deployment of mission critical e-business-based, real-time outage, network and workforce management solutions for the utility sector. The software is a real-time, stand-alone, web-based program built around advanced intelligence and robust algorithms, designed to interface easily and cleanly with embedded outage mitigation and recovery systems. emPower provides extensive procedural and logistical support to successfully integrate crews and equipment, and automatically assigns tasks and schedules them in accordance with defined restoration goals and priorities. emPower also tracks all activities and generates proper reports for internal and external agencies, among them utility management, police, government departments, media, medical facilities, and customers.

A quantitative method to evaluate microbial electrolysis cell effectiveness for energy recovery and wastewater treatment

KAUST Repository

Ivanov, Ivan

2013-10-01

Microbial electrolysis cells (MECs) are potential candidates for sustainable wastewater treatment as they allow for recovery of the energy input by producing valuable chemicals such as hydrogen gas. Evaluating the effectiveness of MEC treatment for different wastewaters requires new approaches to quantify performance, and the establishment of specific procedures and parameters to characterize the outcome of fed-batch treatability tests. It is shown here that Coulombic efficiency can be used to directly calculate energy consumption relative to wastewater treatment in terms of COD removal, and that the average current, not maximum current, is a better metric to evaluate the rate of the bioelectrochemical reactions. The utility of these methods was demonstrated using simulated current profiles and actual wastewater tests. Industrial and domestic wastewaters were evaluated using small volume MECs, and different inoculation strategies. The energy needed for treatment was 2.17kWhkgCOD-1 for industrial wastewater and 2.59kWhkgCOD-1 for domestic wastewater. When these wastewaters were combined in equal amounts, the energy required was reduced to 0.63kWhkgCOD-1. Acclimation of the MEC to domestic wastewater, prior to tests with industrial wastewaters, was the easiest and most direct method to optimize MEC performance for industrial wastewater treatment. A pre-acclimated MEC accomplished the same removal (1847 ± 53 mg L-1) as reactor acclimated to only the industrial wastewater (1839 ± 57 mg L-1), but treatment was achieved in significantly less time (70 h versus 238 h). © 2013, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.

Measuring the Recovery Orientation of ACT

Science.gov (United States)

Salyers, Michelle P.; Stull, Laura G.; Rollins, Angela L.; McGrew, John H.; Hicks, Lia J.; Thomas, Dave; Strieter, Doug

2014-01-01

Background Approaches to measuring recovery orientation are needed, particularly for programs that may struggle with implementing recovery-oriented treatment. Objective A mixed methods comparative study was conducted to explore effective approaches to measuring recovery orientation of Assertive Community Treatment (ACT) teams. Design Two ACT teams exhibiting high and low recovery orientation were compared using surveys, treatment plan ratings, diaries of treatment visits, and team-leader-reported treatment control mechanisms. Results The recovery-oriented team differed on one survey measure (higher expectations for consumer recovery), treatment planning (greater consumer involvement and goal-directed content), and use of control mechanisms (less use of representative payee, agency-held lease, daily medication delivery, and family involvement). Staff and consumer diaries showed the most consistent differences (e.g., conveying hope and choice) and were the least susceptible to observer bias, but had the lowest response rates. Conclusions Several practices differentiate recovery orientation on ACT teams, and a mixed-methods assessment approach is feasible. PMID:23690285

Enhanced oil recovery using improved aqueous fluid-injection methods: an annotated bibliography. [328 citations

Energy Technology Data Exchange (ETDEWEB)

Meister, M.J.; Kettenbrink, G.K.; Collins, A.G.

1976-10-01

This annotated bibliography contains abstracts, prepared by the authors, of articles published between 1968 and early 1976 on tests of improved aqueous fluid injection methods (i.e., polymer and surfactant floods). The abstracts have been written and organized to facilitate studies of the oil recovery potential of polymer and surfactant floods under known reservoir conditions. 328 citations.

The Train Driver Recovery Problem - a Set Partitioning Based Model and Solution Method

DEFF Research Database (Denmark)

Rezanova, Natalia Jurjevna; Ryan, David

2010-01-01

The need to recover a train driver schedule occurs during major disruptions in the daily railway operations. Based on data from the Danish passenger railway operator DSB S-tog A/S, a solution method to the train driver recovery problem (TDRP) is developed. The TDRP is formulated as a set...... branching strategy using the depth-first search of the Branch & Bound tree. The LP relaxation of the TDRP possesses strong integer properties. We present test scenarios generated from the historical real-life operations data of DSB S-tog A/S. The numerical results show that all but one tested instances...... partitioning problem. We define a disruption neighbourhood by identifying a small set of drivers and train tasks directly affected by the disruption. Based on the disruption neighbourhood, the TDRP model is formed and solved. If the TDRP solution provides a feasible recovery for the drivers within...

The centrality of community dynamics in the socio-economic recovery of devastated communities.

Science.gov (United States)

Gomez, A; Atallah, W; Bidaisee, S; Patel, C; Amuleru-Marshall, O

2009-11-01

To assess and explore the health and socio-economic outcomes of Jubilee, a community on the Caribbean island of Grenada hit by Hurricane Ivan in 2004 and to identify remaining barriers to recovery. The assessment consisted of a mixed methods approach employing observations, household surveys, in-depth interviews and focus groups. Eighty-five per cent of the residents live in a single-family home type dwelling which is occupied by multiple families. Twenty-seven per cent of the respondents depended on a river or stream for water and 83% utilized an outdoor pit latrine. Construction accounted for 28% of the employment while 16% reported having no occupation. Public and private transportation was limited and 48% of the residents lived on less than one United States of America (US) dollar per day. Access to healthcare was reported by 89% and the prevalence of diabetes and hypertension was identified by 13% and 30% of the residents respectively. Social fragmentation within the community represents a barrier that keeps the community from developing common goals leading to full economic recovery. Jubilee has not fully recovered from the effects of Hurricane Ivan, but progress has been made in the reconstruction effort. These efforts have addressed the most immediate and basic needs of the community, mainly utility service infrastructure and home repairs. However issues related to the community's economic recovery are still unresolved.

Modelling of Evaporator in Waste Heat Recovery System using Finite Volume Method and Fuzzy Technique

Directory of Open Access Journals (Sweden)

Jahedul Islam Chowdhury

2015-12-01

Full Text Available The evaporator is an important component in the Organic Rankine Cycle (ORC-based Waste Heat Recovery (WHR system since the effective heat transfer of this device reflects on the efficiency of the system. When the WHR system operates under supercritical conditions, the heat transfer mechanism in the evaporator is unpredictable due to the change of thermo-physical properties of the fluid with temperature. Although the conventional finite volume model can successfully capture those changes in the evaporator of the WHR process, the computation time for this method is high. To reduce the computation time, this paper develops a new fuzzy based evaporator model and compares its performance with the finite volume method. The results show that the fuzzy technique can be applied to predict the output of the supercritical evaporator in the waste heat recovery system and can significantly reduce the required computation time. The proposed model, therefore, has the potential to be used in real time control applications.

Drug utilization according to reason for prescribing: a pharmacoepidemiologic method based on an indication hierarchy

DEFF Research Database (Denmark)

Kildemoes, Helle Wallach; Hendriksen, Carsten; Morten, Andersen

2011-01-01

ABSTRACT Purpose To develop a pharmacoepidemiologic method for drug utilization analysis according to indication, gender, and age by means of register-based information. Statin utilization in 2005 was applied as an example. Methods Following the recommendations for statin therapy, we constructed ...

Biomarkers of stroke recovery: Consensus-based core recommendations from the Stroke Recovery and Rehabilitation Roundtable.

Science.gov (United States)

Boyd, Lara A; Hayward, Kathryn S; Ward, Nick S; Stinear, Cathy M; Rosso, Charlotte; Fisher, Rebecca J; Carter, Alexandre R; Leff, Alex P; Copland, David A; Carey, Leeanne M; Cohen, Leonardo G; Basso, D Michele; Maguire, Jane M; Cramer, Steven C

2017-07-01

The most difficult clinical questions in stroke rehabilitation are "What is this patient's potential for recovery?" and "What is the best rehabilitation strategy for this person, given her/his clinical profile?" Without answers to these questions, clinicians struggle to make decisions regarding the content and focus of therapy, and researchers design studies that inadvertently mix participants who have a high likelihood of responding with those who do not. Developing and implementing biomarkers that distinguish patient subgroups will help address these issues and unravel the factors important to the recovery process. The goal of the present paper is to provide a consensus statement regarding the current state of the evidence for stroke recovery biomarkers. Biomarkers of motor, somatosensory, cognitive and language domains across the recovery timeline post-stroke are considered; with focus on brain structure and function, and exclusion of blood markers and genetics. We provide evidence for biomarkers that are considered ready to be included in clinical trials, as well as others that are promising but not ready and so represent a developmental priority. We conclude with an example that illustrates the utility of biomarkers in recovery and rehabilitation research, demonstrating how the inclusion of a biomarker may enhance future clinical trials. In this way, we propose a way forward for when and where we can include biomarkers to advance the efficacy of the practice of, and research into, rehabilitation and recovery after stroke.

Utility of three-dimensional method for diagnosing meniscal lesions

International Nuclear Information System (INIS)

Ohshima, Suguru; Nomura, Kazutoshi; Hirano, Mako; Hashimoto, Noburo; Fukumoto, Tetsuya; Katahira, Kazuhiro

1998-01-01

MRI of the knee is a useful method for diagnosing meniscal tears. Although the spin echo method is usually used for diagnosing meniscal tears, we examined the utility of thin slice scan with the three-dimensional method. We reviewed 70 menisci in which arthroscopic findings were confirmed. In this series, sensitivity was 90.9% for medial meniscal injuries and 68.8% for lateral meniscal injuries. There were 3 meniscal tears in which we could not detect tears on preoperative MRI. We could find tears in two of these cases when re-evaluated using the same MRI. In conclusion, we can get the same diagnostic rate with the three-dimensional method compared with the spin echo method. Scan time of the three-dimensional method is 3 minutes, on the other hand that of spin echo method in 17 minutes. This slice scan with three-dimensional method is useful for screening meniscal injuries before arthroscopy. (author)

Recovery of Lithium From Geothermal Fluid at Lumpur Sidoarjo by Adsorption Method

OpenAIRE

Noerochim, Lukman; Satriawangsa, Gita Akbar; Widodo, Amien

2016-01-01

The recovery of lithium from geothermal fluid at Lumpur Sidoarjo, Indonesia was investigated employing an adsorption method with polymer membrane as container. The lithium concentration in geothermal fluid from Lumpur Sidoarjo used in the present study was about 5 mg/l. Lithium manganese oxide (LMO) was selected as a promising adsorbent material due to its non-toxic, topotactical behavior and low cost. In this study, LMO with single Li/Mn mole ratio was prepared, i.e. Li1.6Mn1.6O4. The adsorb...

An economic and legal perspective on electric utility transition costs

Energy Technology Data Exchange (ETDEWEB)

Rose, K.

1996-07-01

The issue of possibly unrecoverable cost incurred by a utility, or `stranded costs,` has emerged as a major obstacle to developing a competitive generation market. Stranded or transition costs are defined as costs incurred by a utility to serve its customers that were being recovered in rates but are no longer due to availability of lower-priced alternative suppliers. The idea of `stranded cost,` and more importantly arguments for its recovery, is a concept with little basis in economic theory, legal precedence, or precedence in other deregulated industries. The main argument recovery is that the ``regulatory compact`` requires it. This is based on the misconception that the regulator compact is simply: the utility incurs costs on behalf of its customers because of the ``obligation to serve`` so, therefore, customers are obligated to pay. This is a mischaracterization of what the compact was and how it developed. Another argument is that recovery is required for economic efficiency. This presumes, however, a very narrow definition of efficiency based on preventing ``uneconomic`` bypass of the utility and that utilities minimize costs. A broader definition of efficiency and the likelihood of cost inefficiencies in the industry suggest that the cost imposed on customers from inhibiting competition could exceed the gains from preventing uneconomic bypass. Both these issues are examined in this paper.

Cold recovery during regasification of LNG part one: Cold utilization far from the regasification facility

International Nuclear Information System (INIS)

La Rocca, Vincenzo

2010-01-01

The paper deals with cold recovery during LNG regasification. The applications analyzed pertain to the use in deep freezing agro food industry and in space air conditioning facilities in commercial sector (Supermarkets and Hypermarkets) of cold recovered from the regasification process. A modular LNG regasification unit is proposed having the regasification capacity of 2 BCM/year of gas and it is based on use of a Power Cycle working with Ethane, this unit allows operation of cold energy transfer, contained in LNG to be regasified, in a range of temperatures suitable for multipurpose use of cold, reducing regasification process irreversibility. Some electric energy is produced by the Power Cycle, but the purpose of the modular unit is to deliver cold suitable for industrial and commercial use in the proper temperature range utilizing Carbon dioxide as secondary fluid to transfer cold from regasification site to far end users. The subject is divided in two papers: this paper deals with facilities delivering cold released during LNG regasification and related pipeline facilities to transfer cold at far end users while the other paper pertains to analysis of end users applications. Results of a detailed thermodynamic and economic analysis demonstrate the suitability of the proposal.

Cost recovery of NGO primary health care facilities: a case study in Bangladesh

Directory of Open Access Journals (Sweden)

Alam Khurshid

2010-06-01

Full Text Available Abstract Background Little is known about the cost recovery of primary health care facilities in Bangladesh. This study estimated the cost recovery of a primary health care facility run by Building Resources Across Community (BRAC, a large NGO in Bangladesh, for the period of July 2004 - June 2005. This health facility is one of the seven upgraded BRAC facilities providing emergency obstetric care and is typical of the government and private primary health care facilities in Bangladesh. Given the current maternal and child mortality in Bangladesh and the challenges to addressing health-related Millennium Development Goal (MDG targets the financial sustainability of such facilities is crucial. Methods The study was designed as a case study covering a single facility. The methodology was based on the 'ingredient approach' using the allocation techniques by inpatient and outpatient services. Cost recovery of the facility was estimated from the provider's perspective. The value of capital items was annualized using 5% discount rate and its market price of 2004 (replacement value. Sensitivity analysis was done using 3% discount rate. Results The cost recovery ratio of the BRAC primary care facility was 59%, and if excluding all capital costs, it increased to 72%. Of the total costs, 32% was for personnel while drugs absorbed 18%. Capital items were17% of total costs while operational cost absorbed 12%. Three-quarters of the total cost was variable costs. Inpatient services contributed 74% of total revenue in exchange of 10% of total utilization. An average cost per patient was US$ 10 while it was US$ 67 for inpatient and US$ 4 for outpatient. Conclusion The cost recovery of this NGO primary care facility is important for increasing its financial sustainability and decreasing donor dependency, and achieving universal health coverage in a developing country setting. However, for improving the cost recovery of the health facility, it needs to increase

Evidence-based post-exercise recovery strategies in basketball.

Science.gov (United States)

Calleja-González, Julio; Terrados, Nicolás; Mielgo-Ayuso, Juan; Delextrat, Anne; Jukic, Igor; Vaquera, Alejandro; Torres, Lorena; Schelling, Xavier; Stojanovic, Marko; Ostojic, Sergej M

2016-01-01

Basketball can be described as a moderate-to-long duration exercise including repeated bouts of high-intensity activity interspersed with periods of low to moderate active recovery or passive rest. A match is characterized by repeated explosive activities, such as sprints, jumps, shuffles and rapid changes in direction. In top-level modern basketball, players are frequently required to play consecutive matches with limited time to recover. To ensure adequate recovery after any basketball activity (i.e., match or training), it is necessary to know the type of fatigue induced and, if possible, its underlying mechanisms. Despite limited scientific evidence to support their effectiveness in facilitating optimal recovery, certain recovery strategies are commonly utilized in basketball. It is particularly important to optimize recovery because players spend a much greater proportion of their time recovering than they do in training. Therefore, the main aim of this report is to facilitate useful information that may lead to practical application, based on the scientific evidence and applied knowledge specifically in basketball.

Optimization of aspergillus niger nutritional conditions using statistical experimental methods for bio-recovery of manganese from pyrolusite

International Nuclear Information System (INIS)

Mujeeb-ur-Rahman; Yasinzai, M.M.; Tareen, R.B.; Iqbal, A.; Gul, S.; Odhano, E.A.

2011-01-01

Optimization of aspergillus niger nutritional conditions using statistical experimental methods for bio-recovery of manganese from pyrolusite Mujeeb-ur-rahman, Mohammed Masoom Yasinzai, Rasool Bakhsh Tareen, Asim Iqbal, Ejaz Ali Odhano, Shereen Gul. The nutritional requirements for Aspergillus niger PCSIR-06 for bio-recovery of manganese from pyrolusite ore were optimized. Box-Bhenken design and response surface methodology were used for designing of experiment and statistical analysis of the results. This procedure limited the number of actual experiments to 54 for studying the possible interaction between six nutrients. The optimum concentration of the nutrients were Sucrose 148.5 g/L, KH/sub 2/PO/sub 4/ 0.50 g/L, NH/sub 4/NO/sub 3/ 0.33 g/L, MgSO/sub 4/ 0.41 g/L, Zn 23.76 mg/L, Fe 0.18 mg/L for Aspergillus niger to achieve maximum bio-recovery of manganese (82.47 +- 5.67%). The verification run confirmed the predicted optimized concentration of all the six ingredients for maximum bio leaching of manganese and successfully confirmed the use of Box-Bhenken experimental design for maximum bio-recovery. Results also revealed that small and less time consuming experimental designs could be efficient for optimization of bio-recovery processes. (author)

Energy efficiency of substance and energy recovery of selected waste fractions.

Science.gov (United States)

Fricke, Klaus; Bahr, Tobias; Bidlingmaier, Werner; Springer, Christian

2011-04-01

In order to reduce the ecological impact of resource exploitation, the EU calls for sustainable options to increase the efficiency and productivity of the utilization of natural resources. This target can only be achieved by considering resource recovery from waste comprehensively. However, waste management measures have to be investigated critically and all aspects of substance-related recycling and energy recovery have to be carefully balanced. This article compares recovery methods for selected waste fractions with regard to their energy efficiency. Whether material recycling or energy recovery is the most energy efficient solution, is a question of particular relevance with regard to the following waste fractions: paper and cardboard, plastics and biowaste and also indirectly metals. For the described material categories material recycling has advantages compared to energy recovery. In accordance with the improved energy efficiency of substance opposed to energy recovery, substance-related recycling causes lower emissions of green house gases. For the fractions paper and cardboard, plastics, biowaste and metals it becomes apparent, that intensification of the separate collection systems in combination with a more intensive use of sorting technologies can increase the extent of material recycling. Collection and sorting systems must be coordinated. The objective of the overall system must be to achieve an optimum of the highest possible recovery rates in combination with a high quality of recyclables. The energy efficiency of substance related recycling of biowaste can be increased by intensifying the use of anaerobic technologies. In order to increase the energy efficiency of the overall system, the energy efficiencies of energy recovery plants must be increased so that the waste unsuitable for substance recycling is recycled or treated with the highest possible energy yield. Copyright © 2010 Elsevier Ltd. All rights reserved.

Utility planning for decommissioning

International Nuclear Information System (INIS)

Williams, D.H.

1982-01-01

Though the biggest impact on a utility of nuclear power plant decommissioning may occur many years from now, procrastination of efforts to be prepared for that time is unwarranted. Foresight put into action through planning can significantly affect that impact. Financial planning can assure the recovery of decommissioning costs in a manner equitable to customers. Decision-making planning can minimize adverse affects of current decisions on later decommissioning impacts and prepare a utility to be equipped to make later decommissioning decisions. Technological knowledge base planning can support all other planning aspects for decommissioning and prepare a utility for decommissioning decisions. Informed project planning can ward off potentially significant pitfalls during decommissioning and optimize the effectiveness of the actual decommissioning efforts

Recovery methods for detection and quantification of Campylobacter depend on meat matrices and bacteriological or PCR tools.

Science.gov (United States)

Fosse, J; Laroche, M; Rossero, A; Fédérighi, M; Seegers, H; Magras, C

2006-09-01

Campylobacter is one of the main causes of human foodborne bacterial disease associated with meat consumption in developed countries. Therefore, the most effective approach for recovery and detection of Campylobacter from meat should be determined. Two hundred ninety pork skin and chine samples were inoculated with Campylobacter jejuni NCTC 11168 and two strains of Campylobacter coli. Campylobacter cells were then recovered from suspensions and enumerated by direct plating. Campylobacter recovery was evaluated by comparing results for two methods of sample collection (swabbing and mechanical pummeling) and three recovery fluids (peptone water, 5% glucose serum, and demineralized water). End-point multiplex PCR was performed to evaluate the compatibility of the recovery fluids with direct PCR detection techniques. Mean recovery ratios differed significantly between pork skin and chine samples. Ratios were higher for mechanical pummeling (0.53 for pork skin and 0.49 for chine) than for swabbing (0.31 and 0.13, respectively). For pork skin, ratios obtained with peptone water (0.50) and with glucose serum (0.55) were higher than those obtained with demineralized water (0.16). Significant differences were not observed for chine samples. Direct multiplex PCR detection of Campylobacter was possible with pork skin samples. The tools for Campylobacter recovery must be appropriate for the meat matrix to be evaluated. In this study, less than 66% of inoculated Campylobacter was recovered from meat. This underestimation must be taken into account for quantitative risk analysis of Campylobacter infection.

Recovery of mineral oil from waste emulsion using electrocoagulation method

Directory of Open Access Journals (Sweden)

Razali Mohd Najib

2016-01-01

Full Text Available This paper presents a research to recover mineral oil from industrial waste emulsion. This research also evaluates the standard of water produced after the oil recovery. The ecosystem could be polluted if this waste is not treated prior to discharge. The equipment needed for this experiment is power supply (generator, connecting wire and metal plate for providing the coagulant. The chosen plates were aluminium and iron plate. The power supply will be connected to the plate producing anode (positive terminal and cathode (negative terminal. Both plates are immersed into a beaker containing waste emulsion. The charge supplied by the current will cause the aluminium or ferum to dissisipate and became ions. These ions will attract the oil to flock together and float at the surface. The water will then filter by using filter paper. Electrocoagulation was done without addition of chemical thus can prevent the hazard from the chemicals. The samples was sent for oil and grease test. The optimum time needed for recovery of oil was 3 hours. The percentage recovery reach constant trend of 95% afterwards. When the power consumption increases, the percentage recovery also increases. However, the current should be lower than 0.5 ampere as it is the limit that human body can withstand. Thus, power consumption of 27.5 Watt was chosen as optimum value. The oil recovery of at power consumption at 27.5W is 96%. The best plate in the process was the aluminium pair which can recover more than ferum plate. The present work concludes the promising future for waste water treatment by usage of electrocoagulation technique.

Relationship Between Magnitude of Applied Spin Recovery Moment and Ensuing Number of Recovery Turns

Science.gov (United States)

Anglin, Ernie L.

1967-01-01

An analytical study has been made to investigate the relationship between the magnitude of the applied spin recovery moment and the ensuing number of turns made during recovery from a developed spin with a view toward determining how to interpolate or extrapolate spin recovery results with regard to determining the amount of control required for a satisfactory recovery. Five configurations were used which are considered to be representative of modern airplanes: a delta-wing fighter, a stub-wing research vehicle, a boostglide configuration, a supersonic trainer, and a sweptback-wing fighter. The results obtained indicate that there is a direct relationship between the magnitude of the applied spin recovery moments and the ensuing number of recovery turns made and that this relationship can be expressed in either simple multiplicative or exponential form. Either type of relationship was adequate for interpolating or extrapolating to predict turns required for recovery with satisfactory accuracy for configurations having relatively steady recovery motions. Any two recoveries from the same developed spin condition can be used as a basis for the predicted results provided these recoveries are obtained with the same ratio of recovery control deflections. No such predictive method can be expected to give satisfactory results for oscillatory recoveries.

Recov'Heat: An estimation tool of urban waste heat recovery potential in sustainable cities

Science.gov (United States)

Goumba, Alain; Chiche, Samuel; Guo, Xiaofeng; Colombert, Morgane; Bonneau, Patricia

2017-02-01

Waste heat recovery is considered as an efficient way to increase carbon-free green energy utilization and to reduce greenhouse gas emission. Especially in urban area, several sources such as sewage water, industrial process, waste incinerator plants, etc., are still rarely explored. Their integration into a district heating system providing heating and/or domestic hot water could be beneficial for both energy companies and local governments. EFFICACITY, a French research institute focused on urban energy transition, has developed an estimation tool for different waste heat sources potentially explored in a sustainable city. This article presents the development method of such a decision making tool which, by giving both energetic and economic analysis, helps local communities and energy service companies to make preliminary studies in heat recovery projects.

Sample preparation methods for quantitative detection of DNA by molecular assays and marine biosensors

International Nuclear Information System (INIS)

Cox, Annie M.; Goodwin, Kelly D.

2013-01-01

Highlights: • DNA extraction methods affected measured qPCR target recovery. • Recovery and variability differed, sometimes by more than an order of magnitude. • SCODA did not offer significant improvement with PCR-inhibited seawater. • Aggressive lysis did appear to improve target recovery. • Reliable and affordable correction methods are needed for quantitative PCR. -- Abstract: The need for quantitative molecular methods is growing in environmental, food, and medical fields but is hindered by low and variable DNA extraction and by co-extraction of PCR inhibitors. DNA extracts from Enterococcus faecium, seawater, and seawater spiked with E. faecium and Vibrio parahaemolyticus were tested by qPCR for target recovery and inhibition. Conventional and novel methods were tested, including Synchronous Coefficient of Drag Alteration (SCODA) and lysis and purification systems used on an automated genetic sensor (the Environmental Sample Processor, ESP). Variable qPCR target recovery and inhibition were measured, significantly affecting target quantification. An aggressive lysis method that utilized chemical, enzymatic, and mechanical disruption enhanced target recovery compared to commercial kit protocols. SCODA purification did not show marked improvement over commercial spin columns. Overall, data suggested a general need to improve sample preparation and to accurately assess and account for DNA recovery and inhibition in qPCR applications

Recovery of uranium mineral from Liaoning Fengcheng ludwigite ore by gravity concentration

International Nuclear Information System (INIS)

Zhang Tao; Liang Haijun; Xue Xiangxin

2009-01-01

A laboratory research was carried out to recover uranium mineral from Liaoning Fengcheng ludwigite ore. Gravity concentration methods including hydroclone, spiral chute and shaking table were applied in this study. The results show that a concentrate with uranium grade of 0.216% and recovery of 44.24% could be produced from the feed of uranium content 0.006 3%. This research is helpful to comprehensive utilization of the mineral resources. Increasing further uranium mineral liberation degree is the key to improve separation effects. (authors)

The trees and the forest: mixed methods in the assessment of recovery based interventions' processes and outcomes in mental health.

Science.gov (United States)

Hasson-Ohayon, Ilanit; Roe, David; Yanos, Philip T; Lysaker, Paul H

2016-12-01

Recent developments in mental health have emphasized recovery as an outcome for people with serious mental illness (SMI). Accordingly, several studies have attempted to evaluate the process and outcome of recovery-oriented psychosocial interventions. To review and discuss quantitative and qualitative findings from previous efforts to study the impact of five recovery-oriented interventions: Illness Management and Recovery (IMR), Narrative Enhancement and Cognitive Therapy (NECT), Supported Employment (SE), Supported Socialization (SS), and Family Psychoeducation. Reviewing the literature on studies that examine the effectiveness of these interventions by using both quantitative and qualitative approach. Qualitative findings in these studies augment quantitative findings and at times draw attention to unexpected findings and uniquely illuminate the effects of these interventions on self-reflective processes. There is a need for further exploration of how mixed-methods can be implemented to explore recovery-oriented outcomes. Critical questions regarding the implications of qualitative findings are posed.

An Inversion Recovery NMR Kinetics Experiment

Science.gov (United States)

Williams, Travis J.; Kershaw, Allan D.; Li, Vincent; Wu, Xinping

2011-01-01

A convenient laboratory experiment is described in which NMR magnetization transfer by inversion recovery is used to measure the kinetics and thermochemistry of amide bond rotation. The experiment utilizes Varian spectrometers with the VNMRJ 2.3 software, but can be easily adapted to any NMR platform. The procedures and sample data sets in this…

Multiattribute utility theory without expected utility foundations

NARCIS (Netherlands)

Wakker, P.P.; Miyamoto, J.

1996-01-01

Methods for determining the form of utilities are needed for the implementation of utility theory in specific decisions. An important step forward was achieved when utility theorists characterized useful parametric families of utilities, and simplifying decompositions of multiattribute utilities.

Multiattribute Utility Theory without Expected Utility Foundations

NARCIS (Netherlands)

Stiggelbout, A.M.; Wakker, P.P.

1995-01-01

Methods for determining the form of utilities are needed for the implementation of utility theory in specific decisions. An important step forward was achieved when utility theorists characterized useful parametric families of utilities, and simplifying decompositions of multiattribute utilities.

Handbook of solid waste disposal: materials and energy recovery

Energy Technology Data Exchange (ETDEWEB)

Pavoni, J L; Heer, Jr, J E; Hagerty, D J

1975-01-01

Traditional and innovative solid waste disposal techniques and new developments in materials and energy recovery systems are analyzed. Each method is evaluated in terms of system methodology, controlling process parameters, and process requirements, by-products, economics, and case histories. Medium and high temperature incineration; wet pulping; landfill with leachate recirculation; the Hercules, Inc., system; USBM front-end and back-end systems; pyrolysis; waste heat utilization, the Combustion Power Unit-400; use of refuse as a supplementary fuel; and methane production from anaerobic fermentation systems are considered, as well as sanitary landfilling, incineration, and composting. European solid waste management techniques are evaluated for their applicability to the US.

Optimal operation of integrated processes. Studies on heat recovery systems

Energy Technology Data Exchange (ETDEWEB)

Glemmestad, Bjoern

1997-12-31

Separators, reactors and a heat exchanger network (HEN) for heat recovery are important parts of an integrated plant. This thesis deals with the operation of HENs, in particular, optimal operation. The purpose of heat integration is to save energy, but the HEN also introduces new interactions and feedback into the overall plant. A prerequisite for optimisation is that there are extra degrees of freedom left after regulatory control is implemented. It is shown that extra degrees of freedom may not always be utilized for energy optimisation, and a quantitative expression for the degrees of freedom that can be so utilized are presented. A simplified expression that is often valid is also deduced. The thesis presents some improvements and generalisations of a structure based method that has been proposed earlier. Structural information is used to divide possible manipulations into three categories depending on how each manipulation affects the utility consumption. By means of these categories and two heuristic rules for operability, the possible manipulations are ordered in a priority table. This table is used to determine which manipulation should be preferred and which manipulation should be selected if an active manipulation is saturated. It is shown that the method may correspond to split-range control. A method that uses parametric information in addition to structural information is proposed. In this method, the optimal control structure is found through solving an integer programming problem. The thesis also proposes a method that combines the use of steady state optimisation and optimal selection of measurements. 86 refs., 46 figs., 8 tabs.

The utility of harvest recoveries of marked individuals to assess polar bear (Ursus maritimus) survival

Science.gov (United States)

Peacock, Elizabeth; Laake, Jeff; Laidre, Kristin L.; Born, Erik W.; Atkinson, Stephen N.

2012-01-01

Management of polar bear (Ursus maritimus) populations requires the periodic assessment of life history metrics such as survival rate. This information is frequently obtained during short-term capture and marking efforts (e.g., over the course of three years) that result in hundreds of marked bears remaining in the population after active marking is finished. Using 10 additional years of harvest recovery subsequent to a period of active marking, we provide updated estimates of annual survival for polar bears in the Baffin Bay population of Greenland and Canada. Our analysis suggests a decline in survival of polar bears since the period of active marking that ended in 1997; some of the decline in survival can likely be attributed to a decline in springtime ice concentration over the continental shelf of Baffin Island. The variance around the survival estimates is comparatively high because of the declining number of marks available; therefore, results must be interpreted with caution. The variance of the estimates of survival increased most substantially in the sixth year post-marking. When survival estimates calculated with recovery-only and recapture-recovery data sets from the period of active marking were compared, survival rates were indistinguishable. However, for the period when fewer marks were available, survival estimates were lower using the recovery-only data set, which indicates that part of the decline we detected for 2003 – 09 may be due to using only harvest recovery data. Nevertheless, the decline in the estimates of survival is consistent with population projections derived from harvest numbers and earlier vital rates, as well as with an observed decline in the extent of sea ice habitat.

A new blanket tritium recovery experiment with intense DT neutron source at JAEA/FNS

Energy Technology Data Exchange (ETDEWEB)

Ochiai, Kentaro, E-mail: ochiai.kentaro@jaea.go.jp [Japan Atomic Energy Agency, 2-166 Omotedate Obuchi, Rokkasho, Aomori 039-3212 (Japan); Edao, Yuki [Japan Atomic Energy Agency, 2-4 Shirane Shirakata, Tokai, Ibaraki 319-1195 (Japan); Hoshino, Tsuyoshi [Japan Atomic Energy Agency, 2-166 Omotedate Obuchi, Rokkasho, Aomori 039-3212 (Japan); Kawamura, Yoshinori [Japan Atomic Energy Agency, 801-1 Mukoyama, Naka, Ibaraki 311-0193 (Japan); Ohta, Masayuki; Kwon, Saerom; Konno, Chikara [Japan Atomic Energy Agency, 2-4 Shirane Shirakata, Tokai, Ibaraki 319-1195 (Japan)

2016-11-01

Highlights: • For detail investigation of the tritium recovery performance on the fusion reactor blanket, we have started a new blanket tritium recovery experiment with ionization chamber at JAEA/FNS. • A new improved container was provided for the appropriate tritium measurement by IC and also utilized for the enhancement of TPR in the new container. The TPR was calculated with a calculation code MCNP5 and some typical nuclear data libraries and then the radioactivity of the tritium recovery with LSC corresponded with that of calculation. • The tritium release curves by the IC outputs are similar to those by the LSC output. However, it was indicated that the quantitative measurement by IC needed further improvement for the tritium recovery. - Abstract: We have performed the tritium release experiment on the fusion reactor blanket at JAEA/FNS since 2009, and then clarified the ratio of tritium release and the recovered tritium chemical form. In order to acquire the detailed tritium recovery performances, we have started a new blanket tritium recovery experiment with ionization chamber (IC) at JAEA/FNS. For the appropriate tritium measurement with IC, we improved the experimental container and carried out with an intense DT neutron source at JAEA/FNS. From our new experiment, the tritium recovery radioactivity from the LSC measurement corresponds with the calculation within 6%. However, it was pointed out that further improvement in the quantitative tritium measurement by IC method was needed.

Influence of digestion methods on the recovery of Iron, Zinc, Nickel, Chromium, Cadmium and Lead contents in 11 organic residues

Directory of Open Access Journals (Sweden)

Thalita Fernanda Abbruzzini

2014-02-01

Full Text Available There are currently many devices and techniques to quantify trace elements (TEs in various matrices, but their efficacy is dependent on the digestion methods (DMs employed in the opening of such matrices which, although "organic", present inorganic components which are difficult to solubilize. This study was carried out to evaluate the recovery of Fe, Zn, Cr, Ni, Cd and Pb contents in samples of composts and cattle, horse, chicken, quail, and swine manures, as well as in sewage sludges and peat. The DMs employed were acid digestion in microwaves with HNO3 (EPA 3051A; nitric-perchloric digestion with HNO3 + HClO4 in a digestion block (NP; dry ashing in a muffle furnace and solubilization of residual ash in nitric acid (MDA; digestion by using aqua regia solution (HCl:HNO3 in the digestion block (AR; and acid digestion with HCl and HNO3 + H2O2 (EPA 3050. The dry ashing method led to the greatest recovery of Cd in organic residues, but the EPA 3050 protocol can be an alternative method for the same purpose. The dry ashing should not be employed to determine the concentration of Cr, Fe, Ni, Pb and Zn in the residues. Higher Cr and Fe contents are recovered when NP and EPA 3050 are employed in the opening of organic matrices. For most of the residues analyzed, AR is the most effective method for recovering Ni. Microwave-assisted digestion methods (EPA3051 and 3050 led to the highest recovery of Pb. The choice of the DM that provides maximum recovery of Zn depends on the organic residue and trace element analyzed.

Recycling of wastes from uranium mining and metallurgy and recovery of useful resources in China

International Nuclear Information System (INIS)

Pan Yingjie; Xue Jianxin; Chen Zhongqiu

2012-01-01

Recycling of wastes from uranium mining and metallurgy in China and recovery of useful resources are summarized from the aspects such as recovery of uranium from mine water, reusing of waste water, decontaminating and recycling of radioactivity contaminated metal, backfill of gangues and tailings, and comprehensive recovery and utilization of associated uranium deposits. (authors)

A Multi-Approach Evaluation System (MA-ES) of Organic Rankine Cycles (ORC) used in waste heat utilization

International Nuclear Information System (INIS)

Shu, Gequn; Yu, Guopeng; Tian, Hua; Wei, Haiqiao; Liang, Xingyu

2014-01-01

Highlights: • The MA-ES provides comprehensive valuations on ORC used for waste heat utilization. • The MA-ES covers energetic, exergetic and economic evaluations of typical ORCs. • The MA-ES is a general assessing method without restriction to specific ORC condition. • Two ORC cases of ICE waste-heat-recovery are exemplified applying the MA-ES. - Abstract: A Multi-Approach Evaluation System (MA-ES) is established in this paper providing comprehensive evaluations on Organic Rankine Cycles (ORC) used for waste heat utilization. The MA-ES covers three main aspects of typical ORC performance: basic evaluations of energy distribution and system efficiency based on the 1st law of thermodynamics; evaluations of exergy distribution and exergy efficiency based on the 2nd law of thermodynamics; economic evaluations based on calculations of equipment capacity, investment and cost recovery. The MA-ES is reasonably organized aiming at providing a general method of ORC performance assessment, without restrictions to system configurations, operation modes, applications, working fluid types, equipment conditions, process parameters and so on. Two ORC cases of internal combustion engines’ (ICEs) waste-heat-recovery are exemplified to illustrate the applications of the evaluation system. The results clearly revealed the performance comparisons among ORC configurations and working fluids referred. The comparisons will provide credible guidance for ORC design, equipment selection and system construction

Improvement of Particle Recovery Method for Uranium Isotope Analysis Using SIMS

International Nuclear Information System (INIS)

Kim, Taehee; Park, Jinkyu; Lee, Chi-Gyu; Lim, Sang Ho; Han, Sun-Ho

2017-01-01

In this study, we developed a new design of vacuum-suction impactor with wider inlet nozzle and outlet nozzle for guiding particles to disperse the particles on the surface of carbon planchet. We prepared simulated samples with lead dioxide and examined particle recovery yield and degree of dispersion using the conventional vacuum impactor and the newly designed ones with different inlet nozzle diameters. We tried to improve the inlet part of vacuum impactor, in order to increase the recovery yield and disperse the collected particle on carbon planchet. As the diameter of inlet nozzle became larger, the collected particles were better dispersed on planchet. In addition, when the inner diameter of the impactor was 3 mm or 5 mm, the recovery yield was higher than that of conventional impactor. Considering the degree of dispersion and recovery yield, we used the impactor with 5 mm exit diameter and recovered the mixed uranium standard materials for SIMS measurement. We were able to reduce the mixing effect and measure the isotopic ratio more accurately and precisely.

Recovery of light nonaqueous-phase liquids without groundwater pumping

International Nuclear Information System (INIS)

Markley, D.E.; Prince-Larsen, N.

1995-01-01

This paper outlines recovery of light nonaqueous-phase liquids (LNAPL) encountered in the subsurface at a remote natural gas facility. Remediation of LNAPL in the subsurface usually begins with dual pumping of LNAPL and groundwater. However, regulations required that only LNAPL be recovered. Methods were sought for recovering LNAPL from groundwater without pumping groundwater to the surface. Alternative methods of LNAPL recovery, using a variety of skimming pumps, included: LNAPL recovery from large-diameter wells; LNAPL recovery from trenches; LNAPL recovery from small-diameter wells; and vacuum-enhanced recovery of LNAPL while skimming with a belt skimmer. Based on the goals of the site owner and the costs associated with each alternative examined, the recommended method for recovering LNAPL without groundwater pumping was recovery of LNAPL while skimming with a belt skimmer. This paper discusses both the advantages and limitations of this technique

Umbilical Cable Recovery Load Analysis

Institute of Scientific and Technical Information of China (English)

YAN Shu-wang; JIA Zhao-lin; FENG Xiao-wei; LI Shi-tao

2013-01-01

Umbilical cable is a kind of integrated subsea cable widely used in the exploration and exploitation of oil and gas field.The severe ocean environment makes great challenges to umbilical maintenance and repair work.Damaged umbilical is usually recovered for the regular operation of the offshore production system.Analysis on cables in essence is a two-point boundary problem.The tension load at the mudline must be known first,and then the recovery load and recovery angle on the vessel can be solved by use of catenary equation.The recovery analysis also involves umbilicalsoil interaction and becomes more complicated.Calculation methods for recovery load of the exposed and buried umbilical are established and the relationship between the position of touch down point and the recovery load as well as the recovery angle and recovery load are analyzed.The analysis results provide a theoretical reference for offshore on-deck operation.

Controller recovery from equipment failures in air traffic control: A framework for the quantitative assessment of the recovery context

International Nuclear Information System (INIS)

Subotic, Branka; Schuster, Wolfgang; Majumdar, Arnab; Ochieng, Washington

2014-01-01

Air Traffic Control (ATC) involves a complex interaction of human operators (primarily air traffic controllers), equipment and procedures. On the rare occasions when equipment malfunctions, controllers play a crucial role in the recovery process of the ATC system for continued safe operation. Research on human performance in other safety critical industries using human reliability assessment techniques has shown that the context in which recovery from failures takes place has a significant influence on the outcome of the process. This paper investigates the importance of context in which air traffic controller recovery from equipment failures takes place, defining it in terms of 20 Recovery Influencing Factors (RIFs). The RIFs are used to develop a novel approach for the quantitative assessment of the recovery context based on a metric referred to as the Recovery Context Indicator (RCI). The method is validated by a series of simulation exercises conducted at a specific ATC Centre. The proposed method is useful to assess recovery enhancement approaches within ATC centres

An innovative treatment method for an aqueous waste from the enhanced oil recovery process

International Nuclear Information System (INIS)

Alimahmoodi, M.; Mulligan, C.N.

2009-01-01

Anaerobic treatment was evaluated to determine its effectiveness in treating a waste stream from the process of Enhanced Oil Recovery (EOR) to remove solubilized CO 2 (98%) and petroleum hydrocarbons (83%) using formate (2 g/L) and sucrose (2.5 g/L) as electron donors in two consecutive reactors. The method of evolutionary operation (EVOP) factorial design was applied to optimize the system and the net energy ratio (NER) of 3.7 was calculated for the system which showed a sustainable biogas production. This method is less complex than other competitive methods, and in addition to its low energy requirements, it can produce CH 4 from CO 2 as a clean source of energy. (author)

Statistical benchmarking in utility regulation: Role, standards and methods

International Nuclear Information System (INIS)

Newton Lowry, Mark; Getachew, Lullit

2009-01-01

Statistical benchmarking is being used with increasing frequency around the world in utility rate regulation. We discuss how and where benchmarking is in use for this purpose and the pros and cons of regulatory benchmarking. We then discuss alternative performance standards and benchmarking methods in regulatory applications. We use these to propose guidelines for the appropriate use of benchmarking in the rate setting process. The standards, which we term the competitive market and frontier paradigms, have a bearing on method selection. These along with regulatory experience suggest that benchmarking can either be used for prudence review in regulation or to establish rates or rate setting mechanisms directly

Faulted systems recovery experience. Final report, May 1992

International Nuclear Information System (INIS)

1992-05-01

This report addresses the recovery (i.e., return to service from a faulted, or otherwise unavailable, condition) of important nuclear power plant front-line and support systems and equipment. It contains information based on operating experience relative to the times to recover from a variety of plant events. It also indicates the nature of the operator actions involved. This information is intended to provide useful insights to utilities who are undertaking Individual Plant Examinations (IPEs) per Generic Letter 88-20 of the Nuclear Regulatory Commission. The report provides a database of recovery experience primarily derived from Licensee Event Reports (LERs). The database contains recovery duration information for 205 demand events and 98 nondemand events. In particular, it contains recovery durations for 42 pump related and 143 valve related events that are representative of demand conditions. Experience shows that, overall, about one-half of all pumps and valves are recovered in 30 minutes or less. Specific recovery experience is dependent on the equipment type, the plant system involved, and the failure mode encountered. (author)

The work and recovery project: changing organizational culture and practice in New York City outpatient services.

Science.gov (United States)

Pascaris, Alysia; Shields, Leslie Reed; Wolf, Jessica

2008-01-01

Complex and multiple barriers confront out-patient programs in promoting recovery and addressing mental health recipients' work-related goals. This article describes a focused organizational change project utilizing intensive consultation and technical assistance within five New York City outpatient psychiatric services. The project aimed to increase staff exposure to, understanding and use of work-related and recovery-based concepts to promote consumers' recovery and attainment of employment goals. Tailored assessment, curriculum delivery, and identification and implementation of change objectives were useful strategies in promoting change. This change model can serve to assist programs in their efforts to integrate new approaches and to better understand changes among leadership, staff and consumers, and changes in organizational culture and practice required to support a work and recovery-oriented service paradigm. The project experience suggests that adopting and embracing new practices takes time. Varied and incremental steps toward programmatic and operational changes can be significant and can reap authentic sustainable change occurring in the process of learning, experiencing, internalizing and adjusting to new methods of practice.

Feasibility of recovery boiler in paper and pulp industry

International Nuclear Information System (INIS)

Rashid, H.

2010-01-01

in this paper feasibility of recovery boiler in terms of economics and environmental impacts in studied. Recovery boilers are employed in the pulp and paper industry where the cooking agent is recovered by burning black liquor. Cooking agent is exhausted due to the absorption of lignin (a burnable component) in cooking agent in the process of straw cooking. The process of recovery boiler is to remove lignin by combustion from black liquor, and heat is produced during the combustion of lignin which is used to produce steam. Recovery boiler is economical as it is recovering valuable chemicals and steam is produced as a byproduct. Steam from recovery boiler is also used for concentrating weak black liquor to concentrated black liquor recovering 50% of the utility water being used at the plant. The regenerated water in the form of foul condensate is reused in the process. The recovery of hazardous chemicals also reduces load of environmental pollution. Which otherwise can pollute the water reservoirs, and regeneration of water makes it environmentally friendly plant. Construction and challenges in operation of recovery boiler such as smelt-water explosion are also discussed in this paper. (author)

Resolution-recovery-embedded image reconstruction for a high-resolution animal SPECT system.

Science.gov (United States)

Zeraatkar, Navid; Sajedi, Salar; Farahani, Mohammad Hossein; Arabi, Hossein; Sarkar, Saeed; Ghafarian, Pardis; Rahmim, Arman; Ay, Mohammad Reza

2014-11-01

The small-animal High-Resolution SPECT (HiReSPECT) is a dedicated dual-head gamma camera recently designed and developed in our laboratory for imaging of murine models. Each detector is composed of an array of 1.2 × 1.2 mm(2) (pitch) pixelated CsI(Na) crystals. Two position-sensitive photomultiplier tubes (H8500) are coupled to each head's crystal. In this paper, we report on a resolution-recovery-embedded image reconstruction code applicable to the system and present the experimental results achieved using different phantoms and mouse scans. Collimator-detector response functions (CDRFs) were measured via a pixel-driven method using capillary sources at finite distances from the head within the field of view (FOV). CDRFs were then fitted by independent Gaussian functions. Thereafter, linear interpolations were applied to the standard deviation (σ) values of the fitted Gaussians, yielding a continuous map of CDRF at varying distances from the head. A rotation-based maximum-likelihood expectation maximization (MLEM) method was used for reconstruction. A fast rotation algorithm was developed to rotate the image matrix according to the desired angle by means of pre-generated rotation maps. The experiments demonstrated improved resolution utilizing our resolution-recovery-embedded image reconstruction. While the full-width at half-maximum (FWHM) radial and tangential resolution measurements of the system were over 2 mm in nearly all positions within the FOV without resolution recovery, reaching around 2.5 mm in some locations, they fell below 1.8 mm everywhere within the FOV using the resolution-recovery algorithm. The noise performance of the system was also acceptable; the standard deviation of the average counts per voxel in the reconstructed images was 6.6% and 8.3% without and with resolution recovery, respectively. Copyright © 2014 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

Multiattribute Utility Theory without Expected Utility Foundations

NARCIS (Netherlands)

J. Miyamoto (John); P.P. Wakker (Peter)

1996-01-01

textabstractMethods for determining the form of utilities are needed for the implementation of utility theory in specific decisions. An important step forward was achieved when utility theorists characterized useful parametric families of utilities and simplifying decompositions of multiattribute

The Train Driver Recovery Problem - a Set Partitioning Based Model and Solution Method

DEFF Research Database (Denmark)

Rezanova, Natalia Jurjevna; Ryan, David

The need to recover a train driver schedule occurs during major disruptions in the daily railway operations. Using data from the train driver schedule of the Danish passenger railway operator DSB S-tog A/S, a solution method to the Train Driver Recovery Problem (TDRP) is developed. The TDRP...... the depth-first search of the Branch & Bound tree. Preliminarily results are encouraging, showing that nearly all tested real-life instances produce integer solutions to the LP relaxation and solutions are found within a few seconds....

Loop transfer recovery for general observer architecture

DEFF Research Database (Denmark)

Niemann, Hans Henrik; Søgaard-Andersen, Per; Stoustrup, Jakob

1991-01-01

A general and concise formulation is given of the loop transfer recovery (LTR) design problem based on recovery errors. Three types of recovery errors are treated: open loop recovery, sensitivity recovery and input-output recovery errors. The three corresponding versions of the asymptotic recovery...... recovery cases. This general recovery formulation covers all known observer based compensator types as special cases. The conditions given in this setting are effectively the aim of all known LTR design methods. The recovery formulation is interpreted in terms of a modelmatching problem as well, which...... is examined by means of the Q-parametrization. It is shown how the general controller obtained by the Q-parametrization can be written as a Luenberger observer based controller. In all cases, n controller states suffice to achieve recovery. The compensators are characterized for errors both on the input...

Conceptual process design for uranium recovery from sea water

International Nuclear Information System (INIS)

Suzuki, Motoyuki; Chihara, Kazuyuki; Fujimoto, Masahiko; Yagi, Hiroshi; Wada, Akihiko.

1985-01-01

Based on design of uranium recovery process from sea water, total cost for uranium production was estimated. Production scale of 1,000 ton-uranium per year was supposed, because of the big demand for uranium in the second age, i.e., fast breeder reactor age. The process is described as follows: Fluidized bed of hydrous titanium oxide (diameter is 0.1 mm, saturated adsorption capacity is 510 μg-U/g-Ad, adsorption capacity for ten days is 150 μg-U/g-Ad) is supposed, as an example, to be utilized as the primarily concentration unit. Fine adsorbent particles can be transferred as slurry in all of the steps of adsorption, washing, desorption, washing, regeneration. As an example, ammonium carbonate is applied to desorb the adsorbed uranium from titanium oxide. Then, stripping method is adopted for desorbent recovery. As for the secondary concentration, strong basic anion exchange method is supposed. The first step of process design is to determine the mass balance of each component through the whole process system by using the signal diagram. Then, the scale of each unit process, with which the mass balances are satisfied, is estimated by detailed chemical engineering calculation. Also, driving cost of each unit operation is estimated. As a result, minimum total cost of 160,000 yen/kg-U is obtained. Adsorption process cost is 80 to 90 % of the total cost. Capital cost and driving cost are fifty-fifty in the adsorption process cost. Pump driving cost forms a big part of the driving cost. Further concentrated study should be necessary on the adsorption process design. It might be important to make an effort on direct utilization of ocean current for saving the pump driving cost. (author)

Technology strategy for enhanced recovery; Technology Target Areas; TTA3 - enhanced recovery

Energy Technology Data Exchange (ETDEWEB)

2007-07-01

The Norwegian Continental Shelf (NCS) is facing new challenges in reserve replacement and improved recovery in order to maintain the overall oil production rate from the area. A new target for an increase in oil reserves of 800 million Sm3 of oil (5 billion barrels) by year 2015 has been set by NPD. This is an ambitious goal considering several of the large fields are on a steep decline, and most of the recent discoveries are relatively small. A significant part of these increased reserves will have to come from fields currently on production, from reservoir areas that have been partly or fully swept, and it is therefore evident that Enhanced Oil Recovery (EOR) methods have to play a key role in achieving this target. EOR methods can be divided into gas based EOR methods and water based EOR methods. Thermal methods are not considered applicable on the NCS due to the relatively light oils present, and the depth of the reservoirs. Gas Based EOR; Water Based EOR; CO{sub 2} injection; Surfactants; Air injection; Polymer; Nitrogen injection; Alkaline; Flue gas injection; Polymer gels; WAG; MEOR; FAWAG. The former OG21 strategy document gave high priority to Water Alternating Gas (WAG) methods and CO{sub 2} injection for enhanced recovery. A lot of research and development and evaluation projects on CO{sub 2} injection were launched and are on-going, most of these are being CO{sub 2} WAG studies. The main challenge now in order to realize CO{sub 2} injection on the NCS is on CO{sub 2} availability and transport. It is also believed that increasing gas prices will limit the availability of hydrocarbon gas for injection purposes in the future. There is, however, a clear need for developing alternative cost efficient EOR methods that can improve the sweep efficiency significantly. Since a majority of the fields on the NCS are being produced under water flooding (or WAG), methods that can improve the water flooding efficiency by chemical additives are of special interest and

Recovery in psychosis: a Delphi study with experts by experience.

Science.gov (United States)

Law, Heather; Morrison, Anthony P

2014-11-01

This study aimed to establish consensus about the meaning of recovery among individuals with experience of psychosis. A Delphi approach was utilized to allow a large sample of service users to be anonymously consulted about their views on recovery. Service users were invited to take part in a 3-stage consultation process. A total of 381 participants gave their views on recovery in the main stage of this study, with 100 of these taking part in the final review stage. The final list of statements about recovery included 94 items, which were rated as essential or important by >80% of respondents. These statements covered items which define recovery, factors which help recovery, factors which hinder recovery, and factors which show that someone is recovering. As far as we are aware, it is the first study to identify areas of consensus in relation to definitions of recovery from a service user perspective, which are typically reported to be an idiosyncratic process. Implications and recommendations for clinical practice and future research are discussed. © The Author 2014. Published by Oxford University Press on behalf of the Maryland Psychiatric Research Center. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Recovery outcomes of schizophrenia patients treated with paliperidone palmitate in a community setting: patient and provider perspectives on recovery.

Science.gov (United States)

Williams, Wesley; McKinney, Christopher; Martinez, Larry; Benson, Carmela

2016-01-01

This study evaluated the effect of paliperidone palmitate long-acting injectable (LAI) antipsychotic on recovery-oriented mental health outcomes from the perspective of healthcare providers and patients during the treatment of patients with schizophrenia or schizoaffective disorders. Archival data for patients with a primary diagnosis of schizophrenia or schizoaffective disorder receiving ≥6 months of paliperidone palmitate LAI were retrieved from the electronic medical records system at the Mental Health Center of Denver. Mental health recovery was assessed from both a provider's (Recovery Markers Inventory [RMI]) and patient's (Consumer Recovery Measure [CRM]) perspective. A three-level hierarchical linear model (HLM) was utilized to determine changes in CRM and RMI scores by including independent variables in the models: intercept, months from treatment (slope), treatment time period (pretreatment and treatment), age, gender, primary diagnosis, substance abuse diagnosis, concurrent medications, and adherence to paliperidone palmitate LAI. A total of 219 patients were identified and included in the study. Results of the final three-level HLMs indicated an overall increase in CRM scores (p a retrospective, non-comparative design, and did not adjust for multiplicity Conclusions: The current study demonstrates that changes in recovery-oriented mental health outcomes can be detected following the administration of a specific antipsychotic treatment in persons with schizophrenia or schizoaffective disorders. Furthermore, patients receiving paliperidone palmitate LAI can effectively improve recovery-oriented outcomes, thereby supporting the drug's use as schizophrenia treatment from a recovery-oriented perspective.

Recovery of Copper from Copper Slag by Hydrometallurgy Method, from Iraqi Factories Waste

Directory of Open Access Journals (Sweden)

Bahaa Sami Mahdi

2018-05-01

Full Text Available   In this research, the recovery of copper from copper slag is investigated using hydrometallurgy method. Slag samples were taken from Al-Shaheed State Company. The results of the chemical analysis showed that the slag contained 11.4% of copper. The recovery process included two stages; the first stage is leaching using diluted sulfuric acid. The most important variables that effect on the leaching process was studied, such as acid concentration, hydrogen peroxide adding, particle size, liquid to solid, stirring speed and leaching time by changing the condition and the stabilizing of other factors at room temperature.               The second stage is precipitation of copper from leaching solution by zinc powder with different weights and times, at room temperature and 1.5 PH value. The results of the first stage manifested that about 99.7% of the copper have been dissolved at the following operational conditions: 50% acid concentration, 5 ml hydrogen peroxide adding, particle size (-75+53 micron, 1:10 liquid to solid, 500 rpm stirring speed and 25 min of leaching time. The highest percentage of copper precipitation in the second stage was 99.8% when added 3gm zinc powder at 20 min. The XRD result revealed that the predominant phase was pure copper. The results of EDS exhibited that a few percentage of oxygen appeared with copper powder. The final of copper recovery ratio was 99.3% with 99.2% purity.

Interpellating recovery: The politics of 'identity' in recovery-focused treatment.

Science.gov (United States)

Fomiatti, Renae; Moore, David; Fraser, Suzanne

2017-06-01

Much research tends to treat alcohol and other drug 'recovery' as a process of positive identity change and development. In this article, we depart from this dominant approach by examining how the social and material practices of alcohol and other drug treatment are themselves active in the constitution of 'recovery identity'. Using Judith Butler's theorisation of interpellation, we examine the accounts of treatment experiences and practices provided in interviews with people who inject drugs. In contrast to the existing literature, we argue that the 'recovering addict' is a socially produced category rather than a coherent psychological identity. We consider the production of this category in relation to three dynamics identified in the data: (1) the tendency to materialise treatment subjects as both disordered and as 'in control' of these disorders; (2) the production of treatment subjects as enmeshed in suspect social relationships and therefore requiring surveillance as well as social support; and (3) treatment's particular enactment of social context such that it erases stigmatisation and marginalisation and paradoxically performs subjects as entirely individually responsible for relinquishing drug use. These dynamics produce capacities and attributes often ascribed to identity but which are better understood as articulations of epistemological disorder in the state of knowledge about addiction, and its expression in treatment. By way of conclusion, we question the utility of 'recovery identity', conventionally defined, in providing a rationale for treatment. Copyright © 2017 Elsevier B.V. All rights reserved.

The Implementation of E1 Clock Recovery

Directory of Open Access Journals (Sweden)

Wang Ziyu

2016-01-01

Full Text Available Clock transform and recovery is of significant importance in microwave TDM service, and it is always extracted from the E1 line data stream in most cases. However, intrinsically uncertain delay and jitter caused by packet transmission of E1 data information, may lead to the indexes of the data recovery clock exceed the clock performance template. Through analysis of the E1 clock indexes and measuring methods, this paper proposes a new clock recovery method. The method employs two buffers, the first RAM is used as a buffer to deduct excess information, and the second FIFO is used as a buffer to recovery the clock and data. The first buffer has a feedback from the second one, and is able to actively respond to changes in the data link and requests from the second one. The test results validate the effectiveness of the method, and the corresponding scheme is also valuable for the other communication systems.

A time-dependent event tree technique for modelling recovery operations

International Nuclear Information System (INIS)

Kohut, P.; Fitzpatrick, R.

1991-01-01

The development of a simplified time dependent event tree methodology is presented. The technique is especially applicable to describe recovery operations in nuclear reactor accident scenarios initiated by support system failures. The event tree logic is constructed using time dependent top events combined with a damage function that contains information about the final state time behavior of the reactor core. Both the failure and the success states may be utilized for the analysis. The method is illustrated by modeling the loss of service water function with special emphasis on the RCP [reactor coolant pump] seal LOCA [loss of coolant accident] scenario. 5 refs., 2 figs., 2 tabs

Recovery of the irradiated JFETs by thermal annealing

International Nuclear Information System (INIS)

Assaf, J.

2007-10-01

Study about the recovering of irradiated JFET transistors has been reported. The JFETs were damaged totally or partially by exposition to Gamma ray and neutrons. Electronics noise has used to evaluate the effect of radiation and the recovery. The study focused on the recovery by thermal annealing, where samples have been heated gradually until 140 centigrade degree (410 K). The recovery ratio given by this method was higher than that resulted from the relaxation method (time recovery) carried out in the room temperature (300 K), especially for Gamma irradiated samples.(author)

INNOVATIVE MIOR PROCESS UTILIZING INDIGENOUS RESERVOIR CONSTITUENTS

Energy Technology Data Exchange (ETDEWEB)

D.O. Hitzman; A.K. Stepp; D.M. Dennis; L.R. Graumann

2003-09-01

This research program was directed at improving the knowledge of reservoir ecology and developing practical microbial solutions and technologies for improving oil production. The goal was to identify and utilize indigenous microbial populations which can produce beneficial metabolic products and develop a methodology to stimulate those select microbes with nutrient amendments to increase oil recovery. This microbial technology has the capability of producing multiple oil-releasing agents. Experimental laboratory work in model sandpack cores was conducted using microbial cultures isolated from produced water samples. Comparative laboratory studies demonstrating in situ production of microbial products as oil recovery agents were conducted in sand packs with natural field waters using cultures and conditions representative of oil reservoirs. Increased oil recovery in multiple model sandpack systems was achieved and the technology and results were verified by successful field studies. Direct application of the research results has lead to the development of a feasible, practical, successful, and cost-effective technology which increases oil recovery. This technology is now being commercialized and applied in numerous field projects to increase oil recovery. Two field applications of the developed technology reported production increases of 21% and 24% in oil recovery.

Performance assessment techniques for groundwater recovery and treatment systems

Energy Technology Data Exchange (ETDEWEB)

Kirkpatrick, G.L. [Environmental Resources Management, Inc., Exton, PA (United States)

1993-03-01

Groundwater recovery and treatment (pump and treat systems) continue to be the most commonly selected remedial technology for groundwater restoration and protection programs at hazardous waste sites and RCRA facilities nationwide. Implementing a typical groundwater recovery and treatment system includes the initial assessment of groundwater quality, characterizing aquifer hydrodynamics, recovery system design, system installation, testing, permitting, and operation and maintenance. This paper focuses on methods used to assess the long-term efficiency of a pump and treat system. Regulatory agencies and industry alike are sensitive to the need for accurate assessment of the performance and success of groundwater recovery systems for contaminant plume abatement and aquifer restoration. Several assessment methods are available to measure the long-term performance of a groundwater recovery system. This paper presents six assessment techniques: degree of compliance with regulatory agency agreement (Consent Order of Record of Decision), hydraulic demonstration of system performance, contaminant mass recovery calculation, system design and performance comparison, statistical evaluation of groundwater quality and preferably, integration of the assessment methods. Applying specific recovery system assessment methods depends upon the type, amount, and quality of data available. Use of an integrated approach is encouraged to evaluate the success of a groundwater recovery and treatment system. The methods presented in this paper are for engineers and corporate management to use when discussing the effectiveness of groundwater remediation systems with their environmental consultant. In addition, an independent (third party) system evaluation is recommended to be sure that a recovery system operates efficiently and with minimum expense.

Incineration method for plutonium recovery from alpha contaminated organic compounds

International Nuclear Information System (INIS)

Yahata, Taneaki; Abe, Jiro; Kato, Michiharu; Kurihara, Masayoshi

1985-01-01

An incineration method for plutonium recovery from α contaminated organic compounds in a flow of controlled oxygen gas is stated. The species of such thermal decomposition products as hydrocarbons, free carbon, carbon monoxide and hydrogen were determined by mass spectrography. The mixture of the products which are the source of tar or soot was converted to CO 2 and H 2 O in contact with copper oxide catalyst without flaming. This incineration method is composed of two stages. The first stage is the decomposition of organic compounds in the streams of gas mixtures containing oxygen in low ratios. The second stage is the incineration of the decomposition products by catalytic reaction in the streams of gas with higher oxygen ratios. Plutonium was recovered as the form of plutonium dioxide from the incineration residues of the first stage. The behavior of oil was examined as a representative of liquid organic compounds. It was found to evaporate below ca. 500 0 C, but was completely incinerated by the catalytic reaction with copper oxide catalyst in the flow of gas with controlled oxygen amount and was changed to CO 2 and H 2 O. (author)

Utilizing Strategic and Operational Methods for Whole-Community Disaster Planning.

Science.gov (United States)

Franks, Stevee; Seaton, Ellen

2017-12-01

Analysis of response and recovery efforts to disasters over the past 2 decades has identified a consistent gap that plagues the nation in regard to persons with access and functional needs. This gap can be highlighted by Hurricane Katrina, where the majority of those killed were a part of the access and functional needs population. After a disaster, many individuals with access and functional needs require assistance recovering but often have difficulty accessing services and resources. These difficulties are due to a combination of issues, such as health problems and the disruption of community support services. We sought to help bridge this gap by focusing on strategic and operational methods used while planning for the whole community. This article highlights the many partnerships that must be fostered for successful whole-community planning. These partnerships include, but are not limited to, local government departments, health agencies, nonprofit and nongovernmental organizations, and other volunteer organizations. We showcase these methods by using a developmental Post-Disaster Canvassing Plan to highlight planning methods that may aid jurisdictions across the United States in disaster planning for the whole community. (Disaster Med Public Health Preparedness. 2017;11:741-746).

Standard test methods for the strong-base resins used in the recovery of uranium

International Nuclear Information System (INIS)

Ford, M.A.; Lombaard, L.R.

1986-01-01

There are no detailed specifications for the strong-base ion-exchange resins used in continuous ion-exchange plants, and it was considered that a very useful purpose would be served by the publication of a series of standard laboratory tests on which such specifications could be based. This report describes test methods that are relevant to the ion-exchange recovery of uranium. They include tests of the physical properties of strong-base resins (relative density, particle-size distribution, and moisture content) and of their chemical properties (theoretical capacity, equilibrium capacity, kinetics of loading and elution). Included are several supporting procedures that are used in conjunction with these methods

Optimising methods of red cell sedimentation from cord blood to maximise nucleated cell recovery prior to cryopreservation.

Science.gov (United States)

Madkaikar, M; Gupta, M; Ghosh, K; Swaminathan, S; Sonawane, L; Mohanty, D

2007-01-01

Human cord blood is now an established source of stem cells for haematopoietic reconstitution. Red blood cell (RBC) depletion is required to reduce the cord blood unit volume for commercial banking. Red cell sedimentation using hydroxy ethyl starch (HES) is a standard procedure in most cord blood banks. However, while standardising the procedure for cord blood banking, a significant loss of nucleated cells (NC) may be encountered during standard HES sedimentation protocols. This study compares four procedures for cord blood processing to obtain optimal yield of nucleated cells. Gelatin, dextran, 6% HES and 6% HES with an equal volume of phosphate-buffered saline (PBS) were compared for RBC depletion and NC recovery. Dilution of the cord blood unit with an equal volume of PBS prior to sedimentation with HES resulted in maximum NC recovery (99% [99.5 +/- 1.3%]). Although standard procedures using 6% HES are well established in Western countries, they may not be applicable in India, as a variety of factors that can affect RBC sedimentation (e.g., iron deficiency, hypoalbuminaemia, thalassaemia trait, etc.) may reduce RBC sedimentation and thus reduce NC recovery. While diluting cord blood with an equal volume of PBS is a simple method to improve the NC recovery, it does involve an additional processing step.

Method of simultaneous recovery of oil and sulfur from bituminous shales

Energy Technology Data Exchange (ETDEWEB)

1919-02-25

The method consists of means for dry distillation of bituminous shales in furnaces heated from inside to recover simultaneously oil and sulfur, and is characterized by obtaining the sulfur partly in the form of sulfuretted hydrogen as a direct distillation product produced in the upper part of the furnace and partly in the form of free sulfur formed in the reduction zone of the furnace by the reduction of the sulfur dioxide formed in the burning zone. It is also characterized by the recovery of sulfur--in so far as the reduction and formation of sulfur dioxide are concerned--being regulated by means of the corresponding regulation of the proportion of the speed of discharging to the amount of air introduced into the process.

Promoting recovery-oriented practice in mental health services: a quasi-experimental mixed-methods study.

Science.gov (United States)

Gilburt, Helen; Slade, Mike; Bird, Victoria; Oduola, Sheri; Craig, Tom K J

2013-06-13

Recovery has become an increasingly prominent concept in mental health policy internationally. However, there is a lack of guidance regarding organisational transformation towards a recovery orientation. This study evaluated the implementation of recovery-orientated practice through training across a system of mental health services. The intervention comprised four full-day workshops and an in-team half-day session on supporting recovery. It was offered to 383 staff in 22 multidisciplinary community and rehabilitation teams providing mental health services across two contiguous regions. A quasi-experimental design was used for evaluation, comparing behavioural intent with staff from a third contiguous region. Behavioural intent was rated by coding points of action on the care plans of a random sample of 700 patients (400 intervention, 300 control), before and three months after the intervention. Action points were coded for (a) focus of action, using predetermined categories of care; and (b) responsibility for action. Qualitative inquiry was used to explore staff understanding of recovery, implementation in services and the wider system, and the perceived impact of the intervention. Semi-structured interviews were conducted with 16 intervention group team leaders post-training and an inductive thematic analysis undertaken. A total of 342 (89%) staff received the intervention. Care plans of patients in the intervention group had significantly more changes with evidence of change in the content of patient's care plans (OR 10.94. 95% CI 7.01-17.07) and the attributed responsibility for the actions detailed (OR 2.95, 95% CI 1.68-5.18). Nine themes emerged from the qualitative analysis split into two superordinate categories. 'Recovery, individual and practice', describes the perception and provision of recovery orientated care by individuals and at a team level. It includes themes on care provision, the role of hope, language of recovery, ownership and

Exergy analysis and evolutionary optimization of boiler blowdown heat recovery in steam power plants

International Nuclear Information System (INIS)

Vandani, Amin Mohammadi Khoshkar; Bidi, Mokhtar; Ahmadi, Fatemeh

2015-01-01

Highlights: • Heat recovery of boiler blow downed water using a flash tank is modeled. • Exergy destruction of each component is calculated. • Exergy efficiency of the whole system is optimized using GA and PSO algorithms. • Utilizing the flash tank increases the net power and efficiency of the system. - Abstract: In this study, energy and exergy analyses of boiler blowdown heat recovery are performed. To evaluate the effect of heat recovery on the system performance, a steam power plant in Iran is selected and the results of implementation of heat recovery system on the power plant are investigated. Also two different optimization algorithms including GA and PSO are established to increase the plant efficiency. The decision variables are extraction pressure from steam turbine and temperature and pressure of boiler outlet stream. The results indicate that using blowdown recovery technique, the net generated power increases 0.72%. Also energy and exergy efficiency of the system increase by 0.23 and 0.22, respectively. The optimization results show that temperature and pressure of boiler outlet stream have a higher effect on the exergy efficiency of the system in respect to the other decision variables. Using optimization methods, exergy efficiency of the system reaches to 30.66% which shows a 1.86% augmentation with regard to the situation when a flash tank is implemented.

The economics of aquifer storage recovery technology

Energy Technology Data Exchange (ETDEWEB)

David, R.; Pyne, G.

2014-10-01

Aquifer storage recovery (ASR) technology is increasingly being utilized around the world for storing water underground through one or more wells during wet months and other times when water is available for storage. The water is then recovered from the same wells when needed to meet a growing variety of water supply objectives. The economics of ASR constitute the principal reason for its increasing utilization. ASR unit capital costs are typically less than half those of other water supply and water storage alternatives. Unit operating costs are usually only slightly greater than for conventional production well-fields. Marginal costs for ASR storage and recovery provide a powerful tool for making more efficient use of existing infrastructure, providing water supply sustainability and reliability at relatively low cost. The opportunity exists for a careful analysis of the net present value of ASR well-fields, addressing not only the associated capital and operating costs but also the value of the benefits achieved for each of the water supply objectives at each site. (Author)

The economics of aquifer storage recovery technology

International Nuclear Information System (INIS)

David, R.; Pyne, G.

2014-01-01

Aquifer storage recovery (ASR) technology is increasingly being utilized around the world for storing water underground through one or more wells during wet months and other times when water is available for storage. The water is then recovered from the same wells when needed to meet a growing variety of water supply objectives. The economics of ASR constitute the principal reason for its increasing utilization. ASR unit capital costs are typically less than half those of other water supply and water storage alternatives. Unit operating costs are usually only slightly greater than for conventional production well-fields. Marginal costs for ASR storage and recovery provide a powerful tool for making more efficient use of existing infrastructure, providing water supply sustainability and reliability at relatively low cost. The opportunity exists for a careful analysis of the net present value of ASR well-fields, addressing not only the associated capital and operating costs but also the value of the benefits achieved for each of the water supply objectives at each site. (Author)

The relation between work-induced neuroendocrine reactivity and recovery, subjective need for recovery, and health status

NARCIS (Netherlands)

Sluiter, JK; Frings-Dresen, MHW; van der Beek, AJ; Meijman, TF

Objectives: The purpose of this cross-sectional study with repeated measurements was to find out to what extent neuroendocrine reactivity during work and neuroendocrine recovery from work, and work characteristics, are related to subjective need for recovery and perceived health status. Methods:

A dual model approach to ground water recovery trench design

International Nuclear Information System (INIS)

Clodfelter, C.L.; Crouch, M.S.

1992-01-01

The design of trenches for contaminated ground water recovery must consider several variables. This paper presents a dual-model approach for effectively recovering contaminated ground water migrating toward a trench by advection. The approach involves an analytical model to determine the vertical influence of the trench and a numerical flow model to determine the capture zone within the trench and the surrounding aquifer. The analytical model is utilized by varying trench dimensions and head values to design a trench which meets the remediation criteria. The numerical flow model is utilized to select the type of backfill and location of sumps within the trench. The dual-model approach can be used to design a recovery trench which effectively captures advective migration of contaminants in the vertical and horizontal planes

Biomass utilization in the operations of petroleum special recovery; Emprego de biomassa nas operacoes de recuperacao especial de petroleo

Energy Technology Data Exchange (ETDEWEB)

Sampaio, A C.M. [PETROBRAS, Salvador, BA (Brazil)

1985-12-31

This paper presents an alternative to the conventional methods of petroleum recovery that use vapor injection, thus requiring a considerable amount of thermal energy. The production of 3-5 barrels can be made with the combustion of 1 barrel of oil. In order to avoid the consumption of natural gas or fuel oil and the import of its equivalent as a consequence, PETROBRAS is carrying out a project to generate vapor from fuel gas obtained from organic matter. 1 tab.

Interlaboratory evaluation of the AOAC method and the A-1 procedure for recovery of fecal coliforms from foods.

Science.gov (United States)

Andrews, W H; Wilson, C R; Poelma, P L; Bullock, L K; McClure, F D; Gentile, D E

1981-09-01

An interlaboratory evaluation was made of the 96 h AOAC method and the 24 h A-1 procedure for the enumeration of fecal coliforms in samples of yellow corn meal, rye flour, mung beans, raw ground beef, and raw oyster homogenate. Results indicated that the efficiency of the A-1 procedure, measured in terms of recovery of fecal coliforms, and the reproducibility of that recovery were dependent on the particular food being analyzed. Accordingly, until its efficiency can be more fully demonstrated, the A-1 procedure is recommended only as a screening procedure for fecal coliforms in foods.

Sample preparation methods for quantitative detection of DNA by molecular assays and marine biosensors.

Science.gov (United States)

Cox, Annie M; Goodwin, Kelly D

2013-08-15

The need for quantitative molecular methods is growing in environmental, food, and medical fields but is hindered by low and variable DNA extraction and by co-extraction of PCR inhibitors. DNA extracts from Enterococcus faecium, seawater, and seawater spiked with E. faecium and Vibrio parahaemolyticus were tested by qPCR for target recovery and inhibition. Conventional and novel methods were tested, including Synchronous Coefficient of Drag Alteration (SCODA) and lysis and purification systems used on an automated genetic sensor (the Environmental Sample Processor, ESP). Variable qPCR target recovery and inhibition were measured, significantly affecting target quantification. An aggressive lysis method that utilized chemical, enzymatic, and mechanical disruption enhanced target recovery compared to commercial kit protocols. SCODA purification did not show marked improvement over commercial spin columns. Overall, data suggested a general need to improve sample preparation and to accurately assess and account for DNA recovery and inhibition in qPCR applications. Published by Elsevier Ltd.

Method, apparatus, and system for utilizing augmented reality to improve surgery

KAUST Repository

Cali, Corrado

2016-10-13

A method, apparatus, and computer readable medium are provided for utilizing augmented reality visualization to assist surgery. An example method includes generating a three dimensional reconstruction of an image stack representing a target area of a patient, and superimposing, by a head-mounted display, a projection of the three dimensional reconstruction onto a field of view of a user. The method further includes maintaining alignment between the projection and the user\\'s actual view of the target area using a plurality of fiducial markers associated with the target area. In some embodiments, the method further includes scanning the target area to generate the image stack.

Wastewater Treatment Energy Recovery Potential For Adaptation To Global Change: An Integrated Assessment

Science.gov (United States)

Breach, Patrick A.; Simonovic, Slobodan P.

2018-04-01

Approximately 20% of wastewaters globally do not receive treatment, whereas wastewater discharges are projected to increase, thereby leading to excessive water quality degradation of surface waters on a global scale. Increased treatment could help alleviate water quality issues by constructing more treatment plants; however, in many areas there exist economic constraints. Energy recovery methods including the utilization of biogas and incineration of biosolids generated during the treatment process may help to alleviate treatment costs. This study explores the potential for investments in energy recovery from wastewater to increase treatment levels and thus improve surface water quality. This was done by examining the relationships between nutrient over-enrichment, wastewater treatment, and energy recovery at a global scale using system dynamics simulation as part of the ANEMI integrated assessment model. The results show that a significant amount of energy can be recovered from wastewater, which helps to alleviate some of the costs of treatment. It was found that wastewater treatment levels could be increased by 34%, helping to offset the higher nutrient loading from a growing population with access to improved sanitation. The production of renewable natural gas from biogas was found to have the potential to prolong the depletion of natural gas resources used to produce electricity and heat. It is recommended that agricultural nutrient discharges be better managed to help reduce nutrient over-enrichment on global scale. To increase the utility of the simulation, a finer spatial scale should be used to consider regional treatment, economic, and water quality characteristics.

Analysis and development of methods for the recovery of tri-n-butylphosphate (TBP)-30%v/v-degraded dodecane

International Nuclear Information System (INIS)

Dalston, C.O.

1984-01-01

Tri-n-butyl phosphate associated with an inert hydrocarbon is the main solvent used in reprocessing of nuclear irradiated fuel arising of pressurized water reactors. The combined action of radiation and nitric acid cause severe damage to solvent, in reprocessing steps. The recovery of the solvent is, thus, of great importance, since it decreases the amount of the waste and improves the process economy. A comparative analysis of several methods of the recovery of this solvent was carried out, such as: alkaline washing, adsorption with resins, adsorption with aluminium oxide, adsorption by active carbon and adsorption by vermiculite. Some modifications of analytical 95 Zr test and a mathematical definition of two new parameters (degradation grade and efficiency of recovery) were done. Through this modified 95 Zr test, the residence time and the rate of degraded solvent: recuperator were determined. After laboratory tests, vermiculite associated with active carbon was employed for the treatment of 50 liters of tri-n-butyl phosphate (30% V/V)-dodecane, degraded by hydrolysis. Other analyses were performed to check the potentialities of these solids for this solvent recovery. (Author) [pt

Emotional rigidity negatively impacts remission from anxiety and recovery of well-being.

Science.gov (United States)

Wiltgen, Anika; Shepard, Christopher; Smith, Ryan; Fowler, J Christopher

2018-08-15

Emotional rigidity is described in clinical literature as a significant barrier to recovery; however, few there are few empirical measures of the construct. The current study had two aims: Study 1 aimed to identify latent factors that may bear on the construct of emotional rigidity while Study 2 assessed the potential impact of the latent factor(s) on anxiety remission rates and well-being. This study utilized data from 2472 adult inpatients (1176 females and 1296 males) with severe psychopathology. Study 1 utilized exploratory factor analysis (EFA) and confirmatory factor analysis (CFA) to identify latent factors of emotional rigidity. Study 2 utilized hierarchical logistic regression analyses to assess the relationships among emotional rigidity factors and anxiety remission and well-being recovery at discharge. Study 1 yielded a two-factor solution identified in EFA was confirmed with CFA. Factor 1 consisted of neuroticism, experiential avoidance, non-acceptance of emotions, impaired goal-directed behavior, impulse control difficulties and limited access to emotion regulation strategies when experiencing negative emotions. Factor 2 consisted of lack of emotional awareness and lack of emotional clarity when experiencing negative emotions. Results of Study 2 indicated higher scores on Factor 1 was associated with lower remission rates from anxiety and poorer well-being upon discharge. Factor 2 was not predictive of outcome. Emotional rigidity appears to be a latent construct that negatively impacts remission rates from anxiety. Limitations of the present study include its retrospective design, and inefficient methods of assessing emotional rigidity. Copyright © 2018. Published by Elsevier B.V.

A method of incident angle estimation for high resolution spectral recovery in filter-array-based spectrometers

Science.gov (United States)

Kim, Cheolsun; Lee, Woong-Bi; Ju, Gun Wu; Cho, Jeonghoon; Kim, Seongmin; Oh, Jinkyung; Lim, Dongsung; Lee, Yong Tak; Lee, Heung-No

2017-02-01

In recent years, there has been an increasing interest in miniature spectrometers for research and development. Especially, filter-array-based spectrometers have advantages of low cost and portability, and can be applied in various fields such as biology, chemistry and food industry. Miniaturization in optical filters causes degradation of spectral resolution due to limitations on spectral responses and the number of filters. Nowadays, many studies have been reported that the filter-array-based spectrometers have achieved resolution improvements by using digital signal processing (DSP) techniques. The performance of the DSP-based spectral recovery highly depends on the prior information of transmission functions (TFs) of the filters. The TFs vary with respect to an incident angle of light onto the filter-array. Conventionally, it is assumed that the incident angle of light on the filters is fixed and the TFs are known to the DSP. However, the incident angle is inconstant according to various environments and applications, and thus TFs also vary, which leads to performance degradation of spectral recovery. In this paper, we propose a method of incident angle estimation (IAE) for high resolution spectral recovery in the filter-array-based spectrometers. By exploiting sparse signal reconstruction of the L1- norm minimization, IAE estimates an incident angle among all possible incident angles which minimizes the error of the reconstructed signal. Based on IAE, DSP effectively provides a high resolution spectral recovery in the filter-array-based spectrometers.

The long-term power purchase: Recovery of capacity costs

International Nuclear Information System (INIS)

Cross, P.S.

1990-01-01

As electric utilities increase their reliance on the long-term power purchase as an alternative to utility-owned generation, the appropriate rate treatment of the costs established in the purchase agreement assumes growing importance. In the November 9, 1989, issue, the authors examined the recent trend among state regulators to treat the long-term purchase in a manner similar to the addition by a utility of a new plant, including a full-scale prudence review. This installment will review recent rulings on the related issue of rate recovery of long-term capacity costs through the fuel cost adjustment clause

Effect of Physical Methods of Lymphatic Drainage on Postexercise Recovery of Mixed Martial Arts Athletes.

Science.gov (United States)

Zebrowska, Aleksandra; Trybulski, Robert; Roczniok, Robert; Marcol, Wieslaw

2017-08-16

Physical methods are reported to be important for accelerating skeletal muscle regeneration, decreasing muscle soreness, and shortening of the recovery time. The aim of the study was to assess the effect of the physical methods of lymphatic drainage (PMLD) such as manual lymphatic drainage (MLD), the Bodyflow (BF) therapy, and lymphatic drainage by deep oscillation (DO) on postexercise regeneration of the forearm muscles of mixed martial arts (MMA) athletes. Eighty MMA athletes aged 27.5 ± 6.4 years were allocated to 4 groups: MLD, the BF device, DO therapy, and the control group. Blood flow velocity in the cephalic vein was measured with the ultrasound Doppler velocity meter. Maximal strength of the forearm muscles (Fmax), muscle tissue tension, pain threshold, blood lactate concentration (LA), and activity of creatine kinase were measured in all groups at rest, after the muscle fatigue test (post-ex) and then 20 minutes, 24, and 48 hours after the application of PMLD. The muscle fatigue test reduced Fmax in all subjects, but in the groups receiving MLD, DO, and BF significantly higher Fmax was observed at recovery compared with post-ex values. The application of MDL reduced the postexercise blood LA and postexercise muscle tension. The lymphatic drainage methods, whether manual or using electro-stimulation and DO, improve postexercise regeneration of the forearm muscles of MMA athletes. The methods can be an important element of therapeutic management focused on optimizing training effects and reducing the risk of injuries of the combat sports athletes.

Combustion for Enhanced Recovery of Light Oil at Medium Pressures

NARCIS (Netherlands)

Khoshnevis Gargar, N.

2014-01-01

Using conventional production methods, recovery percentages from oil reservoirs range from 5% for difficult oil to 50% for light oil in highly permeable homogeneous reservoirs. To increase the oil recovery factor, enhanced oil recovery (EOR) methods are used. We distinguish EOR that uses chemical

Dengue viral infection monitoring from diagnostic to recovery using Raman spectroscopy

International Nuclear Information System (INIS)

Firdous, Shamaraz; Anwar, Shahzad

2015-01-01

Raman spectroscopy has been found useful for monitoring the dengue patient diagnostic and recovery after infection. In the present work, spectral changes that occurred in the blood sera of a dengue infected patient and their possible utilization for monitoring of infection and recovery were investigated using 532 nm wavelength of light. Raman spectrum peaks for normal and after recovery of dengue infection are observed at 1527, 1170, 1021 cm −1 attributed to guanine, adenine, TRP (protein) carbohydrates peak for solids, and skeletal C–C stretch of lipids acyl chains. Where in the dengue infected patient Raman peaks are at 1467, 1316, 1083, and 860 attributed to CH2/CH3 deformation of lipids and collagen, guanine (B, Z-marker), lipids and protein bands. Due to antibodies and antigen reactions the portions and lipids concentration totally changes in dengue viral infection compared to normal blood. These chemical changes in blood sera of dengue viral infection in human blood may be used as possible markers to indicate successful remission and suggest that Raman spectroscopy may provide a rapid optical method for continuous monitoring or evaluation of a protein bands and an antibodies population. Accumulate acquisition mode was used to reduce noise and thermal fluctuation and improve signal to noise ratio. This in vitro dengue infection monitoring methodology will lead in vivo noninvasive on-line monitoring and screening of viral infected patients and their recovery. (letter)

Prudent management of utility assets -- Problem or promise?

International Nuclear Information System (INIS)

Hatch, D.; Serwinowski, M.

1998-01-01

As utilities move into a deregulated market, the extent and nature of their asset base, as well as, the manner in which they have managed it, may play a key factor in the form of regulatory recovery. Utilities must face the issue of stranded assets. One form of addressing this issue is using ''EVA'', Economic Value Added as a mechanism to form financial models for prudent asset management. The authors present an approach to this challenging aspect of deregulation. They focus on the following utility assets: buildings/facilities, and excess real physical assets. Primarily focusing on Niagara Mohawk, two or three case studies are used to demonstrate how proactive management and EVA analysis transforms underperforming utility assets. These will be presented in a way that can show benefits for all utility stakeholders such as cost avoidance, load growth, real estate tax savings, stranded asset reductions, environmental gains, corporate image enhancement, and regulatory/governmental gains; over and above possible economic gains. Examples will be given that include the transformation of utility assets into award winning commercial, residential, and industrial developments as well as recreational/park lands and greenways. Similarly, other examples will show the many tangible and intangible benefits of an effective investment recovery and waste stream management program. Various strategies will also be presented that detail how utilities can begin to develop a total comprehensive plan for their asset portfolio. The first step in realizing and maximizing EVA towards a portfolio of assets is a change in corporate policy--one from passive ownership to active prudent management. Service and cost will drive competition resulting from full deregulation. To drive down costs, utilities will need to become more efficient in dealing with their asset base. By embracing an EVA model on an entire asset portfolio, utilities can prepare and excel in the newly shaped marketplace

Hospice utilization during the SARS outbreak in Taiwan

Directory of Open Access Journals (Sweden)

Lin Ming-Hwai

2006-08-01

Full Text Available Abstract Background The severe acute respiratory syndrome (SARS epidemic threw the world into turmoil during the first half of 2003. Many subsequent papers have addressed its impact on health service utilization, but few have considered palliative (hospice care. The aim of the present study was to describe changes in hospice inpatient utilization during and after the SARS epidemic in 2003 in Taiwan. Methods The data sources were the complete datasets of inpatient admissions during 2002 and 2003 from the National Health Insurance Research Database. Before-and-after comparisons of daily and monthly utilizations were made. Hospice analyses were limited to those wards that offered inpatient services throughout these two years. The comparisons were extended to total hospital bed utilization and to patients who were still admitted to hospice wards during the peak period of the SARS epidemic. Results Only 15 hospice wards operated throughout the whole of 2002 and 2003. In 2003, hospice utilization began to decrease in the middle of April, reached a minimum on 25 May, and gradually recovered to the level of the previous November. Hospices showed a more marked reduction in utilization than all hospital beds (e.g. -52.5% vs. -19.9% in May 2003 and a slower recovery with a three-month lag. In total, 566 patients were admitted to hospice wards in May/June 2003, in contrast to 818 in May/June 2002. Gender, age and diagnosis distributions did not differ. Conclusion Hospice inpatient utilization in Taiwan was indeed more sensitive to the emerging epidemic than general inpatient utilization. A well-balanced network with seamless continuity of care should be ensured.

Power recovery method for testing the efficiency of the ECD of an integrated generation unit for offshore wind power and ocean wave energy

Institute of Scientific and Technical Information of China (English)

CHEN WeiXing; GAO Feng; MENG XiangDun; REN AnYe; HU Yan

2017-01-01

Offshore wind power and ocean wave energy are clean,renewable and rich resources.The integrated generation unit for the two kinds of energy is introduced.The energy conversion device (ECD) is utilized to convert the mechanical energy absorbed from the wind power and wave energy into the hydraulic energy,the conversion efficiency of which is significant.In this paper,a power recovery method for testing the efficiency of the ECD is proposed.A simulation desktop is developed to validate the proposed method.The efficiency of the ECD is influenced by the hydraulic cylinders and the mechanical transmission.Here,the static efficiency of the hydraulic cylinders of the ECD is tested first.The results show that the static mechanical efficiency is about 95 ％ and that the volumetric efficiency is over 99％.To test the effects induced by the mechanical transmission of the ECD,each hydraulic cylinder of the ECD is substituted with two springs.Then the power loss of the ECDM under different rotational speeds is obtained.Finally,a test platform is built and the efficiency of the ECD under different rotational speeds and pressures is obtained.The results show that the efficiency is about 80％.

Human skeletal muscle glycogen utilization in exhaustive exercise

DEFF Research Database (Denmark)

Nielsen, Joachim; Holmberg, Hans-Christer; Schrøder, Henrik Daa

2011-01-01

Although glycogen is known to be heterogeneously distributed within skeletal muscle cells, there is presently little information available about the role of fibre types, utilization and resynthesis during and after exercise with respect to glycogen localization. Here, we tested the hypothesis...... to be influenced by fibre type prior to exercise, as well as carbohydrate availability during the subsequent period of recovery. These findings provide insight into the significance of fibre type-specific compartmentalization of glycogen metabolism in skeletal muscle during exercise and subsequent recovery. ....... that utilization of glycogen with different subcellular localizations during exhaustive arm and leg exercise differs and examined the influence of fibre type and carbohydrate availability on its subsequent resynthesis. When 10 elite endurance athletes (22 ± 1 years, VO2 max = 68 ± 5 ml kg-1 min-1, mean ± SD...

A Mineralogical Assessment on Residues after Acidic Leaching of Bauxite Residue (Red Mud) for Titanium Recovery

OpenAIRE

Gözde Alkan; Claudia Schier; Lars Gronen; Srecko Stopic; Bernd Friedrich

2017-01-01

Due to its alkalinity, red mud produced by the Bayer process may affect both the environment and human health. For this reason, its further utilization instead of disposal is of great importance. Numerous methods have already been studied for hydrometallurgical treatment of red mud, especially for the recovery of various metallic components such as iron, aluminum, titanium or rare earth elements. This study focuses on the extraction of titanium from red mud and in particular the mineralogical...

Sampling methods for recovery of human enteric viruses from environmental surfaces.

Science.gov (United States)

Turnage, Nicole L; Gibson, Kristen E

2017-10-01

Acute gastroenteritis causes the second highest infectious disease burden worldwide. Human enteric viruses have been identified as leading causative agents of acute gastroenteritis as well as foodborne illnesses in the U.S. and are generally transmitted by fecal-oral contamination. There is growing evidence of transmission occurring via contaminated fomite including food contact surfaces. Additionally, human enteric viruses have been shown to remain infectious on fomites over prolonged periods of time. To better understand viral persistence, there is a need for more studies to investigate this phenomenon. Therefore, optimization of surface sampling methods is essential to aid in understanding environmental contamination to ensure proper preventative measures are being applied. In general, surface sampling studies are limited and highly variable among recovery efficiencies and research parameters used (e.g., virus type/density, surface type, elution buffers, tools). This review aims to discuss the various factors impacting surface sampling of viruses from fomites and to explore how researchers could move towards a more sensitive and standard sampling method. Copyright © 2017 Elsevier B.V. All rights reserved.

Substances stimulating recovery for radiation injury

Energy Technology Data Exchange (ETDEWEB)

Takeda, A; Yonezawa, M; Katoh, N [Radiation Center of Osaka Prefecture, Sakai (Japan)

1978-11-01

A relationship between radiation injury and its recovery (intracellular recovery, intercellular recovery, or individual recovery) was discussed. In addition to histological researches in Japan, some substances (free radicals, endotoxin, vaccine, crude drugs, tissue extracts, blood platelet, etc.) stimulating recovery for radiation injury were introduced, and the progress of the study by the authors was summarized. Effects of a root of Panax ginseng (it is believed to accelerate segmentation of marrow cells, and synthesis of DNA and protein in rats and men), methods of its extracting and administration, its influences upon hemogram and organ weight in animal experiments, exclusion of side effects, period of administration, and purification of its effective components were reported.

General introduction and recovery factors

Science.gov (United States)

Verma, Mahendra K.

2017-07-17

IntroductionThe U.S. Geological Survey (USGS) compared methods for estimating an incremental recovery factor (RF) for the carbon dioxide enhanced oil recovery (CO2-EOR) process involving the injection of CO2 into oil reservoirs. This chapter first provides some basic information on the RF, including its dependence on various reservoir and operational parameters, and then discusses the three development phases of oil recovery—primary, second­ary, and tertiary (EOR). It ends with a brief discussion of the three approaches for estimating recovery factors, which are detailed in subsequent chapters.

LOWER COST METHODS FOR IMPROVED OIL RECOVERY (IOR) VIA SURFACTANT FLOODING

Energy Technology Data Exchange (ETDEWEB)

William A. Goddard III; Yongchun Tang; Patrick Shuler; Mario Blanco; Seung Soon Jang; Shiang-Tai Lin; Prabal Maiti; Yongfu Wu; Stefan Iglauer; Xiaohang Zhang

2004-09-01

This report provides a summary of the work performed in this 3-year project sponsored by DOE. The overall objective of this project is to identify new, potentially more cost-effective surfactant formulations for improved oil recovery (IOR). The general approach is to use an integrated experimental and computational chemistry effort to improve our understanding of the link between surfactant structure and performance, and from this knowledge, develop improved IOR surfactant formulations. Accomplishments for the project include: (1) completion of a literature review to assemble current and new surfactant IOR ideas, (2) Development of new atomistic-level MD (molecular dynamic) modeling methodologies to calculate IFT (interfacial tension) rigorously from first principles, (3) exploration of less computationally intensive mesoscale methods to estimate IFT, Quantitative Structure Property Relationship (QSPR), and cohesive energy density (CED) calculations, (4) experiments to screen many surfactant structures for desirable low IFT and solid adsorption behavior, and (5) further experimental characterization of the more promising new candidate formulations (based on alkyl polyglycosides (APG) and alkyl propoxy sulfate surfactants). Important findings from this project include: (1) the IFT between two pure substances may be calculated quantitatively from fundamental principles using Molecular Dynamics, the same approach can provide qualitative results for ternary systems containing a surfactant, (2) low concentrations of alkyl polyglycoside surfactants have potential for IOR (Improved Oil Recovery) applications from a technical standpoint (if formulated properly with a cosurfactant, they can create a low IFT at low concentration) and also are viable economically as they are available commercially, and (3) the alkylpropoxy sulfate surfactants have promising IFT performance also, plus these surfactants can have high optimal salinity and so may be attractive for use in higher

A Method to Predict Compressor Stall in the TF34-100 Turbofan Engine Utilizing Real-Time Performance Data

Science.gov (United States)

2015-06-01

A METHOD TO PREDICT COMPRESSOR STALL IN THE TF34-100 TURBOFAN ENGINE UTILIZING REAL-TIME PERFORMANCE...THE TF34-100 TURBOFAN ENGINE UTILIZING REAL-TIME PERFORMANCE DATA THESIS Presented to the Faculty Department of Systems Engineering and...036 A METHOD TO PREDICT COMPRESSOR STALL IN THE TF34-100 TURBOFAN ENGINE UTILIZING REAL-TIME PERFORMANCE DATA Shuxiang ‘Albert’ Li, BS

Different methods to define utility functions yield similar results but engage different neural processes

Directory of Open Access Journals (Sweden)

Marcus Heldmann

2009-10-01

Full Text Available Although the concept of utility is fundamental to many economic theories, up to now a generally accepted method determining a subject’s utility function is not available. We investigated two methods that are used in economic sciences for describing utility functions by using response-locked event-related potentials in order to assess their neural underpinnings. For defining the certainty equivalent (CE, we used a lottery game with probabilities to win p=0.5, for identifying the subjects’ utility functions directly a standard bisection task was applied. Although the lottery tasks’ payoffs were only hypothetical, a pronounced negativity was observed resembling the error related negativity (ERN previously described in action monitoring research, but this occurred only for choices far away from the indifference point between money and lottery. By contrast, the bisection task failed to evoke an ERN irrespective of the responses’ correctness. Based on these findings we are reasoning that only decisions made in the lottery task achieved a level of subjective relevance that activates cognitive-emotional monitoring. In terms of economic sciences, our findings support the view that the bisection method is unaffected by any kind of probability valuation or other parameters related to risk and in combination with the lottery task can, therefore, be used to differentiate between payoff and probability valuation.

Apparatus and method for materials processing utilizing a rotating magnetic field

Science.gov (United States)

Muralidharan, Govindarajan; Angelini, Joseph A.; Murphy, Bart L.; Wilgen, John B.

2017-04-11

An apparatus for materials processing utilizing a rotating magnetic field comprises a platform for supporting a specimen, and a plurality of magnets underlying the platform. The plurality of magnets are configured for rotation about an axis of rotation intersecting the platform. A heat source is disposed above the platform for heating the specimen during the rotation of the plurality of magnets. A method for materials processing utilizing a rotating magnetic field comprises providing a specimen on a platform overlying a plurality of magnets; rotating the plurality of magnets about an axis of rotation intersecting the platform, thereby applying a rotating magnetic field to the specimen; and, while rotating the plurality of magnets, heating the specimen to a desired temperature.

Application of Portfolio Theory in Recovery Planning for Pacific Salmon.

Science.gov (United States)

Ecological applications of portfolio theory demonstrate the utility of this analytical framework for understanding the stability of commercial and indigenous Pacific Salmon fisheries. Portfolio theory also has the potential to aid in recovery planning for threatened and endangere...

Quality of recovery after anaesthesia measured with QoR-40: a prospective observational study

Directory of Open Access Journals (Sweden)

Luís Guimarães-Pereira

Full Text Available Abstract Background: QoR-40, a 40-item questionnaire on quality of recovery from anaesthesia, has been shown to measure health status after surgery. Our aim was to evaluate the incidence of poor quality of recovery in our Post Anaesthesia Care Unit and to compare their QoR-40 scores before surgery and 3 months later. Methods: A prospective observational study was conducted in adult patients consecutively admitted from 18 June to 12 July 2012. The follow-up period was 3 months. We exclude patients submitted to cardiac surgery, neurosurgery, obstetric surgery and with a mini-mental state examination test score lower than 25. The primary endpoint was quality of recovery measured with the validated Portuguese for Portugal version of the QoR-40 before surgery (T0, 24 h after surgery (T1 and 3 months after (T2. Results: A total of 114 patients completed the study. Mean QoR-40 score was 169 and patients with poor quality of recovery were identified if their QoR-40 score was lesser than 142. This occurred in 26 patients (24%. Global median scores for patients with poor quality of recovery were lower at T0 (121 vs. 184, p < 0.001, at T1 (120 vs. 177, p < 0.001 and at T2 (119 vs. 189, p < 0.001. Conclusion: Patients with poor quality of recovery had lower quality of life. This fact may allow earlier and more effective interventions, in order to improve quality of life after surgery. Beside its utility after surgery, QoR-40 may be important prior to surgery to identify patients who will develop a poor quality of recovery.

Recovery of Lithium from Geothermal Fluid at Lumpur Sidoarjo by Adsorption Method

Directory of Open Access Journals (Sweden)

Lukman Noerochim

2016-05-01

Full Text Available The recovery of lithium from geothermal fluid at Lumpur Sidoarjo, Indonesia was investigated employing an adsorption method with polymer membrane as container. The lithium concentration in geothermal fluid from Lumpur Sidoarjo used in the present study was about 5 mg/l. Lithium manganese oxide (LMO was selected as a promising adsorbent material due to its non-toxic, topotactical behavior and low cost. In this study, LMO with single Li/Mn mole ratio was prepared, i.e. Li1.6Mn1.6O4. The adsorbent was synthesized by solid state reaction at 500 °C for 5 hrs. A lithium uptake yield from the geothermal fluid of around 6.6 mg/g was obtained.

UTILIZATION OF RENEWABLE ENERGIES AND CHANGINGENERGY STUCTURE AT LOCAL GOVERMENT, AS DRIVERS OFECONOMIC RECOVERY: HUNGARIAN CASE STUDY

Directory of Open Access Journals (Sweden)

György Gonda

2011-07-01

Full Text Available The growth and stability of the world economy is hindered because of theexhaustion of the fossil and traditional energy sources and because ofenvironmental consequences and increasing costs oftheir use. The energy supplyof is increasingly unstable and unsafe because in countries which suffer from highdependence of energy import. The traditional sectors have been facing recessionduring the last couple of years and the recovery also highly depends on newsolutions in energy supply. The rural regions are more vulnerable from botheconomic and social, because their adaptive capacities are limited. The main goalis this paper is to show the key factors of the limited possibilities of theirrecovery, such as low level of income, high rate ofunemployment and migration,high share of unskilled labour, lack of capital andappropriate know-how inenergetics. Development requires a new approach inenergetics, in agriculture andalso in waste management, resulting in high utilization of the renewable energiesgenerating regional economic growth. In this paper,a Hungarian case study willbe presented, which will show one solution of a rural municipality for viability,stability, job creation, and economic and social development. The paper concludesthe necessity of the role of the public private partnership and of the increasingsocial capital, in the future economic environmental and social balance in the ruralarea.

High-order simulation of foam enhanced oil recovery

NARCIS (Netherlands)

Van der Meer, J.M.; Van Odyck, D.E.A.; Wirnsberger, P.; Jansen, J.D.

2014-01-01

If secondary hydrocarbon recovery methods fail because of the occurrence of gravity override or viscous fingering one can turn to an enhanced oil recovery method like the injection of foam. The generation of foam can be described by a set of partial differential equations with strongly nonlinear

Primary studies on particle recovery of swipe samples for nuclear safeguards

International Nuclear Information System (INIS)

Fan Wang; Yan Chen; Yong-gang Zhao; Yan Zhang; Tong-xing Wang; Jing-huai Li; Zhi-yuan Chang; Hai-ping Cui

2013-01-01

Environmental sampling plays a significant role in nuclear safeguards. Isotopic ratio in uranium-bearing particles from swipe samples provides important information for detecting undeclared activities. Particle recovery which is the primary step of particle analysis, would affect the following analysis. The particle recovery efficiency of ultrasoneration recovery and vacuum suction-impact recovery were measured by alpha spectrometer with standard particles produced via aerosol spray pyrolysis method. The conditions of ultrasoneration were optimized and both recovery methods were evaluated. Finally, a procedure of particle recovery for unknown swipe samples was set up. (author)

Adaptation to and Recovery from Global Catastrophe

Directory of Open Access Journals (Sweden)

Seth D. Baum

2013-03-01

Full Text Available Global catastrophes, such as nuclear war, pandemics and ecological collapse threaten the sustainability of human civilization. To date, most work on global catastrophes has focused on preventing the catastrophes, neglecting what happens to any catastrophe survivors. To address this gap in the literature, this paper discusses adaptation to and recovery from global catastrophe. The paper begins by discussing the importance of global catastrophe adaptation and recovery, noting that successful adaptation/recovery could have value on even astronomical scales. The paper then discusses how the adaptation/recovery could proceed and makes connections to several lines of research. Research on resilience theory is considered in detail and used to develop a new method for analyzing the environmental and social stressors that global catastrophe survivors would face. This method can help identify options for increasing survivor resilience and promoting successful adaptation and recovery. A key point is that survivors may exist in small isolated communities disconnected from global trade and, thus, must be able to survive and rebuild on their own. Understanding the conditions facing isolated survivors can help promote successful adaptation and recovery. That said, the processes of global catastrophe adaptation and recovery are highly complex and uncertain; further research would be of great value.

Recovery of salmonella serovar enteritidis from inoculated broiler hatching eggs using shell rinse and shell crush sampling methods

Science.gov (United States)

This study compared the recovery of Salmonella from hatching eggs using three sampling methods (eggshell rinsing, eggshell crush following a previous rinse, and eggshell crush without previous rinse). Eggshells were drop-inoculated with approximately 10, 100, or 1,000 cfu/eggshell of S. Enteritidis...

Cost utility analysis of diagnostic method of syphilis

Directory of Open Access Journals (Sweden)

Viroj Wiwanitkit

2008-04-01

Full Text Available Presently, the diagnosis of syphilis is dependent mainly on serological tests. The most widely used screening tests for syphilis are the VDRL and the rapid plasma reagin (RPR and for confirmation, the fluorescent treponemal antibody (FTA and the treponema pallidum hemagglutination (TPHA tests. The four alternative modes for diagnosis of syphilis can be a VDRL + FTA, b VDRL + TPHA, c RPR + FTA and d RPR + TPHA. Here the author reports an evaluation of cost utility of these tests in medical practice. It is shown that the cost per accurate diagnosis with VDRL + TPH is the least expensive choice. Therefore, this alternative is the best method for serological diagnosis for syphilis, based on medical laboratory economics principles

Comparison of two ultra-sensitive methods for the determination of 232Th by recovery corrected pre-concentration radiochemical neutron activation analysis

International Nuclear Information System (INIS)

Glover, S.E.; Qu, H.; LaMont, S.P.; Grimm, C.A.; Filby, R.H.

2001-01-01

The determination of isotopic thorium by alpha spectrometric methods is a routine practice for bioassay and environmental measurement programs. Alpha-spectrometry has excellent detection limits (by mass) for all isotopes of thorium except 232 Th due to its extremely long half-life. Improvements in the detection limit an sensitivity over previously reported methods of pre-concentration neutron activation analysis (PCNAA) for the recovery corrected, isotopic determination of thorium in various matrices is discussed. Following irradiation, the samples were dissolved, 231 Pa added as a tracer, and Pa isolated by two different methods and compared (extraction chromatography and anion exchange chromatography) followed by alpha spectrometry for recovery correction. Ion exchange chromatography was found to be superior for this application at this time, principally for reliability. The detection limit for 232 Th of 3.5 x 10 -7 Bq is almost three orders of magnitude lower than for alpha spectrometry using the PCRNAA method and one order of magnitude below previously reported PCNAA methods. (author)

Comparison of a radiometric method (BACTEC) and conventional culture media for recovery of mycobacteria from smear-negative specimens

International Nuclear Information System (INIS)

Morgan, M.A.; Horstmeier, C.D.; DeYoung, D.R.; Roberts, G.D.

1983-01-01

The BACTEC system and three conventional media (Middlebrook 7H10, selective Middlebrook 7H11 [S7H11], and Lowenstein-Jensen [LJ] were compared for their mean recovery times and recovery rates of mycobacteria from acid-fast, smear-negative clinical specimens. Of the 71 smear-negative, culture-positive specimens recovered from 2,165 submitted smear-negative cultures, the BACTEC system detected 71.8%, compared with 88.7% for the conventional three-medium system. When media were individually compared, BACTEC medium (Middlebrook 7H12) was more successful in recovering mycobacteria (71.8%) than was LJ (62%), Middlebrook medium 7H10 (55.9%), or Middlebrook S7H11 medium (52.1%). Middlebrook 7H11 medium containing sodium selenate was also evaluated and did not increase the recovery rate or decrease the recovery time of mycobacterial species when compared with LJ, Middlebrook 7H10, S7H11, and 7H12 media. The mean detection time for the BACTEC system was less than that by conventional methods for the seven species of mycobacteria recovered. Detection times for Mycobacterium tuberculosis on the BACTEC system and conventional cultural systems were 13.7 and 26.3 days, respectively

In College and in Recovery: Reasons for Joining a Collegiate Recovery Program

Science.gov (United States)

Laudet, Alexandre B.; Harris, Kitty; Kimball, Thomas; Winters, Ken C.; Moberg, D. Paul

2016-01-01

Objective: Collegiate Recovery Programs (CRPs), a campus-based peer support model for students recovering from substance abuse problems, grew exponentially in the past decade, yet remain unexplored. Methods: This mixed-methods study examines students' reasons for CRP enrollment to guide academic institutions and referral sources. Students (N =…

Assessment of net lost revenue adjustment mechanisms for utility DSM programs

Energy Technology Data Exchange (ETDEWEB)

Baxter, L.W.

1995-01-01

Utility shareholders can lose money on demand-side management (DSM) investments between rate cases. Several industry analysts argue that the revenues lost from utility DSM programs are an important financial disincentive to utility DSM investment. A key utility regulatory reform undertaken since 1989 allows utilities to recover the lost revenues incurred through successful operation of DSM programs. Explicitly defined net lost revenue adjustment (NLRA) mechanisms are states` preferred approach to lost revenue recovery from DSM programs. This report examines the experiences states and utilities are having with the NLRA approach. The report has three objectives. First, we determine whether NLRA is a feasible and successful approach to removing the lost-revenue disincentive to utility operation of DSM programs. Second, we identify the conditions linked to successful implementation of NLRA mechanisms in different states and assess whether NLRA has changed utility investment behavior. Third, we suggest improvements to NLRA mechanisms. We first identify states with NLRA mechanisms where utilities are recovering lost revenues from DSM programs. We interview staff at regulatory agencies in all these states and utility staff in four states. These interviews focus on the status of NLRA, implementation issues, DSM measurement issues, and NLRA results. We also analyze regulatory agency orders on NLRA, as well as associated testimony, reports, and utility lost revenue recovery filings. Finally, we use qualitative and quantitative indicators to assess NLRA`s effectiveness. Contrary to the concerns raised by some industry analysts, our results indicate NLRA is a feasible approach to the lost-revenue disincentive.

A method to simulate motor control strategies to recover from perturbations: application to a stumble recovery during gait.

Science.gov (United States)

Forner-Cordero, Arturo; Ackermann, Marko; de Lima Freitas, Mateus

2011-01-01

Perturbations during human gait such as a trip or a slip can result in a fall, especially among frail populations such as the elderly. In order to recover from a trip or a stumble during gait, humans perform different types of recovery strategies. It is very useful to uncover the mechanisms of the recovery to improve training methods for populations at risk of falling. Moreover, human recovery strategies could be applied to implement controllers for bipedal robot walker, as an application of biomimetic design. A biomechanical model of the response to a trip during gait might uncover the control mechanisms underlying the different recovery strategies and the adaptation of the responses found during the execution of successive perturbation trials. This paper introduces a model of stumble in the multibody system framework. This model is used to assess different feedforward strategies to recover from a trip. First of all, normal gait patterns for the musculoskeletal system model are obtained by solving an optimal control problem. Secondly, the reference gait is perturbed by the application of forces on the swinging foot in different ways: as an instantaneous inelastic collision of the foot with an obstacle, as an impulsive horizontal force or using a force curve measured experimentally during gait perturbation experiments. The influence of the type of perturbation, the timing of the collision with respect to the gait cycle, as well as of the coefficient of restitution was investigated previously. Finally, in order to test the effects of different muscle excitation levels on the initial phases of the recovery response, several muscle excitations were added to selected muscles of the legs, thus providing a simulation of the recovery reactions. These results pave the way for future analysis and modeling of the control mechanisms of gait.

Valuable metals - recovery processes, current trends, and recycling strategies

Energy Technology Data Exchange (ETDEWEB)

Froehlich, Peter; Lorenz, Tom; Martin, Gunther; Brett, Beate; Bertau, Martin [Institut fuer Technische Chemie, TU Bergakademie Freiberg, Leipziger Strasse 29, 09599, Freiberg (Germany)

2017-03-01

This Review provides an overview of valuable metals, the supply of which has been classified as critical for Europe. Starting with a description of the current state of the art, novel approaches for their recovery from primary resources are presented as well as recycling processes. The focus lies on developments since 2005. Chemistry strategies which are used in metal recovery are summarized on the basis of the individual types of deposit and mineral. In addition, the economic importance as well as utilization of the metals is outlined. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

Heat Recovery From Tail Gas Incineration To Generate Power

Energy Technology Data Exchange (ETDEWEB)

Tawfik, Tarek

2010-09-15

Many industrial processes result in tail gas wastes that must be flared or incinerated to abide with environmental guidelines. Tail gas incineration occurs in several chemical processes resulting in high-temperature exhaust gas that simply go to the stack, thus wasting all that valuable heat! This paper discusses useful heat recovery and electric power generation utilizing available heat in exhaust gas from tail gas incinerators. This heat will be recovered in a waste-heat recovery boiler that will produce superheated steam to expand in a steam turbine to generate power. A detailed cost estimate is presented.

A review of waste heat recovery technologies for maritime applications

International Nuclear Information System (INIS)

Singh, Dig Vijay; Pedersen, Eilif

2016-01-01

Highlights: • Major waste heat sources available on ships have been reviewed. • A review of suitable waste heat recovery systems was conducted for marine vessels. • Technologies have been compared for their potential and suitability for marine use. • Kalina cycle offers the highest potential for marine waste heat recovery. • Turbo compound system most suitable for recovering diesel exhaust pressure energy. - Abstract: A waste heat recovery system produces power by utilizing the heat energy lost to the surroundings from thermal processes, at no additional fuel input. For marine vessels, about 50 percent of the total fuel energy supplied to diesel power-plant aboard is lost to the surroundings. While the total amount of wasted energy is considerable, the quality of this energy is quite low due to its low temperature and has limited potential for power production. Effective waste heat recovery systems use the available low temperature waste heat to produce mechanical/electrical power with high efficiency value. In this study a review of different waste heat recovery systems has been conducted, to lay out the potential recovery efficiencies and suitability for marine applications. This work helps in identifying the most suitable heat recovery technologies for maritime use depending on the properties of shipboard waste heat and achievable recovery efficiencies, whilst discussing the features of each type of system.

Development of a higher-order finite volume method for simulation of thermal oil recovery process using moving mesh strategy

Energy Technology Data Exchange (ETDEWEB)

Ahmadi, M. [Heriot Watt Univ., Edinburgh (United Kingdom)

2008-10-15

This paper described a project in which a higher order up-winding scheme was used to solve mass/energy conservation equations for simulating steam flood processes in an oil reservoir. Thermal recovery processes are among the most complex because they require a detailed accounting of thermal energy and chemical reaction kinetics. The numerical simulation of thermal recovery processes involves localized phenomena such as saturation and temperatures fronts due to hyperbolic features of governing conservation laws. A second order accurate FV method that was improved by a moving mesh strategy was used to adjust for moving coordinates on a finely gridded domain. The Finite volume method was used and the problem of steam injection was then tested using derived solution frameworks on both mixed and moving coordinates. The benefits of using a higher-order Godunov solver instead of lower-order ones were qualified. This second order correction resulted in better resolution on moving features. Preferences of higher-order solvers over lower-order ones in terms of shock capturing is under further investigation. It was concluded that although this simulation study was limited to steam flooding processes, the newly presented approach may be suitable to other enhanced oil recovery processes such as VAPEX, SAGD and in situ combustion processes. 23 refs., 28 figs.

Application of the High Temperature Gas Cooled Reactor to oil shale recovery

International Nuclear Information System (INIS)

Wadekamper, D.C.; Arcilla, N.T.; Impellezzeri, J.R.; Taylor, I.N.

1983-01-01

Current oil shale recovery processes combust some portion of the products to provide energy for the recovery process. In an attempt to maximize the petroleum products produced during recovery, the potentials for substituting nuclear process heat for energy generated by combustion of petroleum were evaluated. Twelve oil shale recovery processes were reviewed and their potentials for application of nuclear process heat assessed. The High Temperature Gas Cooled Reactor-Reformer/Thermochemical Pipeline (HTGR-R/TCP) was selected for interfacing process heat technology with selected oil shale recovery processes. Utilization of these coupling concepts increases the shale oil product output of a conventional recovery facility from 6 to 30 percent with the same raw shale feed rate. An additional benefit of the HTGR-R/TCP system was up to an 80 percent decrease in emission levels. A detailed coupling design for a typical counter gravity feed indirect heated retorting and upgrading process were described. Economic comparisons prepared by Bechtel Group Incorporated for both the conventional and HTGR-R/TCP recovery facility were summarized

Fluid diversion in oil recovery

International Nuclear Information System (INIS)

Nimir, Hassan B.

1999-01-01

In any oil recovery process, large scale heterogeneities, such as fractures, channels, or high-permeability streaks, can cause early break through of injected fluid which will reduce oil recovery efficiency. In waterflooding, enhanced oil recovery, and acidizing operations, this problem is particularly acute because of the cost of the injected fluid. On the other hand coping with excess water production is always a challenging task for field operators. The cost of handling and disposing produced water can significantly shorten the economic production life of an oil well. The hydrostatic pressure created by high fluid levels in a well (water coning) is also detrimental to oil production. In this paper, the concept of fluid diversion is explained. Different methods that are suggested to divert the fluid into the oil-bearing-zones are briefly discussed, to show their advantages and disadvantages. Methods of reducing water production in production well are also discussed. (Author)

Enhancing gold recovery from electronic waste via lixiviant metabolic engineering in Chromobacterium violaceum

Science.gov (United States)

Tay, Song Buck; Natarajan, Gayathri; Rahim, Muhammad Nadjad bin Abdul; Tan, Hwee Tong; Chung, Maxey Ching Ming; Ting, Yen Peng; Yew, Wen Shan

2013-01-01

Conventional leaching (extraction) methods for gold recovery from electronic waste involve the use of strong acids and pose considerable threat to the environment. The alternative use of bioleaching microbes for gold recovery is non-pollutive and relies on the secretion of a lixiviant or (bio)chemical such as cyanide for extraction of gold from electronic waste. However, widespread industrial use of bioleaching microbes has been constrained by the limited cyanogenic capabilities of lixiviant-producing microorganisms such as Chromobacterium violaceum. Here we show the construction of a metabolically-engineered strain of Chromobacterium violaceum that produces more (70%) cyanide lixiviant and recovers more than twice as much gold from electronic waste compared to wild-type bacteria. Comparative proteome analyses suggested the possibility of further enhancement in cyanogenesis through subsequent metabolic engineering. Our results demonstrated the utility of lixiviant metabolic engineering in the construction of enhanced bioleaching microbes for the bioleaching of precious metals from electronic waste. PMID:23868689

Mathematical models utilized in the retrieval of displacement information encoded in fringe patterns

Science.gov (United States)

Sciammarella, Cesar A.; Lamberti, Luciano

2016-02-01

All the techniques that measure displacements, whether in the range of visible optics or any other form of field methods, require the presence of a carrier signal. A carrier signal is a wave form modulated (modified) by an input, deformation of the medium. A carrier is tagged to the medium under analysis and deforms with the medium. The wave form must be known both in the unmodulated and the modulated conditions. There are two basic mathematical models that can be utilized to decode the information contained in the carrier, phase modulation or frequency modulation, both are closely connected. Basic problems connected to the detection and recovery of displacement information that are common to all optical techniques will be analyzed in this paper, focusing on the general theory common to all the methods independently of the type of signal utilized. The aspects discussed are those that have practical impact in the process of data gathering and data processing.

Design manual. [High temperature heat pump for heat recovery system

Energy Technology Data Exchange (ETDEWEB)

Burch, T.E.; Chancellor, P.D.; Dyer, D.F.; Maples, G.

1980-01-01

The design and performance of a waste heat recovery system which utilizes a high temperature heat pump and which is intended for use in those industries incorporating indirect drying processes are described. It is estimated that use of this heat recovery system in the paper, pulp, and textile industries in the US could save 3.9 x 10/sup 14/ Btu/yr. Information is included on over all and component design for the heat pump system, comparison of prime movers for powering the compressor, control equipment, and system economics. (LCL)

Microbial Enhanced Oil Recovery: 3D Simulation with Gravity Effects

DEFF Research Database (Denmark)

Nielsen, Sidsel Marie; Jessen, K.; Shapiro, Alexander

2010-01-01

Microbial enhanced oil recovery (MEOR) utilizes the activity of microorganisms, where microorganisms simultaneously grow in a reservoir and convert substrate into recovery enhancing products (usually, surfactants). In order to predict the performance of a MEOR process, a simulation tool is required...... using an operator splitting technique. To the best of our knowledge, this has resulted in the first full 3D MEOR streamline simulator. For verification purposes, we compare results from our streamline MEOR simulator to those of a conventional finite difference approach for 1D and 2D displacement...

A New Method to Individualize Monitoring of Muscle Recovery in Athletes.

Science.gov (United States)

Hecksteden, Anne; Pitsch, Werner; Julian, Ross; Pfeiffer, Mark; Kellmann, Michael; Ferrauti, Alexander; Meyer, Tim

2017-10-01

Assessment of muscle recovery is essential for the daily fine-tuning of training load in competitive sports, but individual differences may limit the diagnostic accuracy of group-based reference ranges. This article reports an attempt to develop individualized reference ranges using a Bayesian approach comparable to that developed for the Athlete Biological Passport. Urea and creatine kinase (CK) were selected as indicators of muscle recovery. For each parameter, prior distributions and repeated-measures SDs were characterized based on data of 883 squad athletes (1758 data points, 1-8 per athlete, years 2013-2015). Equations for the individualization procedure were adapted from previous material to allow for discrimination of 2 physiological states (recovered vs nonrecovered). Evaluation of classificatory performance was carried out using data from 5 consecutive weekly microcycles in 14 elite junior swimmers and triathletes. Blood samples were collected every Monday (recovered) and Friday according to the repetitive weekly training schedule over 5 wk. On the group level, changes in muscle recovery could be confirmed by significant differences in urea and CK and validated questionnaires. Group-based reference ranges were derived from that same data set to avoid overestimating the potential benefit of individualization. For CK, error rates were significantly lower with individualized classification (P vs group-based: test-pass error rate P = .008; test-fail error rate P < .001). For urea, numerical improvements in error rates failed to reach significance. Individualized reference ranges seem to be a promising tool to improve accuracy of monitoring muscle recovery. Investigating application to a larger panel of indicators is warranted.

Comparative assessment of alternative cycles for waste heat recovery and upgrade

International Nuclear Information System (INIS)

Little, Adrienne B.; Garimella, Srinivas

2011-01-01

Thermally activated systems based on sorption cycles, as well as mechanical systems based on vapor compression/expansion are assessed in this study for waste heat recovery applications. In particular, ammonia-water sorption cycles for cooling and mechanical work recovery, a heat transformer using lithium bromide-water as the working fluid pair to yield high temperature heat, and organic Rankine cycles using refrigerant R245fa for work recovery as well as versions directly coupled to a vapor compression cycle to yield cooling are analyzed with overall heat transfer conductances for heat exchangers that use similar approach temperature differences for each cycle. Two representative cases are considered, one for smaller-scale and lower temperature applications using waste heat at 60 o C, and the other for larger-scale and higher temperature waste heat at 120 o C. Comparative assessments of these cycles on the basis of efficiencies and system footprints guide the selection of waste heat recovery and upgrade systems for different applications and waste heat availabilities. Furthermore, these considerations are used to investigate four case studies for waste heat recovery for data centers, vehicles, and process plants, illustrating the utility and limitations of such solutions. The increased implementation of such waste heat recovery systems in a variety of applications will lead to decreased primary source inputs and sustainable energy utilization. -- Highlights: → Sorption and mechanical pathways for the conversion of waste heat streams to work, cooling, and temperature boosting were investigated. → Waste heat sources including 300 W of energy at 60 o C and 1 kW of energy at 120 o C were analyzed. → Up to about seventy percent of the input waste heat can be converted to cooling. → Up to about ten percent can be converted to work. → Up to about 47 percent can be upgraded to a higher temperature.

Study on tritium recovery from breeder materials

International Nuclear Information System (INIS)

Moriyama, H.; Moritani, K.

1997-01-01

For the development of fusion reactor blanket systems, some of the key issues on the tritium recovery performance of solid and liquid breeder materials were studied. In the case of solid breeder materials, a special attention was focussed on the effects of irradiation on the tritium recovery performance, and tritium release experiments, luminescence measurements of irradiation defects and modeling studies were systematically performed. For liquid breeder materials, tritium recovery experiments from molten salt and liquid lithium were performed, and the technical feasibility of tritium recovery methods was discussed. (author)

Coabsorbent and thermal recovery compression heat pumping technologies

CERN Document Server

Staicovici, Mihail-Dan

2014-01-01

This book introduces two of the most exciting heat pumping technologies, the coabsorbent and the thermal recovery (mechanical vapor) compression, characterized by a high potential in primary energy savings and environmental protection. New cycles with potential applications of nontruncated, truncated, hybrid truncated, and multi-effect coabsorbent types are introduced in this work.   Thermal-to-work recovery compression (TWRC) is the first of two particular methods explored here, including how superheat is converted into work, which diminishes the compressor work input. In the second method, thermal-to-thermal recovery compression (TTRC), the superheat is converted into useful cooling and/or heating, and added to the cycle output effect via the coabsorbent technology. These and other methods of discharge gas superheat recovery are analyzed for single-, two-, three-, and multi-stage compression cooling and heating, ammonia and ammonia-water cycles, and the effectiveness results are given.  The author presen...

POLLUTION PREVENTION IN THE SEMICONDUCTOR INDUSTRY THROUGH RECOVERY AND RECYCLING OF GALLIUM AND ARSENIC FROM GAAS POLISHING WASTES

Science.gov (United States)

A process was developed for the recovery of both arsenic and gallium from gallium arsenide polishing wastes. The economics associated with the current disposal techniques utilizing ferric hydroxide precipitation dictate that sequential recovery of toxic arsenic and valuble galliu...

Recovery of Americium-241 from lightning rod by the method of chemical treatment

International Nuclear Information System (INIS)

Cruz, W.H.

2013-01-01

About 95% of the lightning rods installed in the Peruvian territory have set in their structures, pose small amounts of radioactive sources such as Americium-241 ( 241 Am), fewer and Radium 226 ( 226 Ra) these are alpha emitters and have a half life of 432 years and 1600 years respectively. In this paper describes the recovery of radioactive sources of 241 Am radioactive lightning rods using the conventional chemical treatment method using agents and acids to break down the slides. The 241 Am recovered was as excitation source and alpha particle generator for analysing samples by X Ray Fluorescence, for fixing the stainless steel 241 Am technique was used electrodeposition. (author)

Development of a recovery method of 131I in the 99Mo process through the fission of 235U

International Nuclear Information System (INIS)

Bignardi, Aline Moraes Teixeira

2013-01-01

13 1 I is an iodine radioisotope widely used in nuclear medicine that can be used either for diagnostic or for treatment due to its physical decay by β - and its high emission of y-rays. It is produced at IPEN using the indirect reaction: 130 Te(n,y) 131m Te → 131 Te → 131 I where TeO 2 targets are irradiated in a Nuclear Reactor. There is also the possibility of producing 131 I by the fission of 235 U, where about 300 different elements are produced together with 131 I. The 131 I produced through this method presents high specific activity and radioactive concentration suitable for the labeling of molecules. The aim of this work was to develop a recovery method of 131 I with the required quality to be used in Nuclear Medicine in the 99 Mo production process through the route of acid dissolution of metallic 235 U targets. 131 I can appear in two phases of the process, both in the gaseous phase produced during the dissolution of metallic U targets and in the dissolution solution. This work studied the recovery of 131 I in these two phases. Several materials were used for the capture and recovery of 131 I at the two phases of the process, the gaseous one and the solution of dissolution of U targets. Columns of alumina with Cu, acid alumina with Cu, Ag microspheres, Cu microspheres, Ag nanospheres, anionic cartridges, Ag cartridges, anion exchange resin and activated charcoal columns were tested. Solutions containing 131 I in 0.1 mol.L -1 NaOH were percolated through the materials and the eluted solutions were analyzed in a dose calibrator. The precipitation of AgI was also studied wth further dissolution of this precipitate with 0.1 mol L -1 NH 4 OH and 5% Na 2 S 2 O 3 . The recovery results varied according to the material, activated charcoal showed recovery yields between 42% and 83% but the recovery yield of the alumina column with Cu ranged from 20% to 85%. Tests with Ag nanospheres showed recovery yield of 26% using 0.1 mol L -1 NaOH and 72% for Na 2 S 2 O

A simple method for measuring glucose utilization of insulin-sensitive tissues by using the brain as a reference

International Nuclear Information System (INIS)

Namba, Hiroki; Nakagawa, Keiichi; Iyo, Masaomi; Fukushi, Kiyoshi; Irie, Toshiaki

1994-01-01

A simple method, without measurement of the plasma input function, to obtain semiquantitative values of glucose utilization in tissues other than the brain with radioactive deoxyglucose is reported. The brain, in which glucose utilization is essentially insensitive to plasma glucose and insulin concentrations, was used as an internal reference. The effects of graded doses of oral glucose loading (0.5, 1 and 2 mg/g body weight) on insulin-sensitive tissues (heart, muscle and fat tissue) were studied in the rat. By using the brain-reference method, dose-dependent increases in glucose utilization were clearly shown in all the insulin-sensitive tissues examined. The method seems to be of value for measurement of glucose utilization using radioactive deoxyglucose and positron emission tomography in the heart or other insulin-sensitive tissues, especially during glucose loading. (orig.)

Report on achievements in proliferation project to introduce environment harmonizing type coal utilization system in fiscal 1998. Joint demonstration project for CMG recovery and utilization system in fiscal 1998; Kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo. 1998 nendo CMG kaishu riyo system kyodo jissho jigyo seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-09-01

This paper describes the discussion report for fiscal 1998 on the CMG (coal methane gas) recovery and utilization project to be implemented from fiscal 1998 through fiscal 2002 at Tiefa Mining Bureau of Liaoning Province in China. The Daixing mine was selected as the survey object. The introduced technologies and facilities include test drilling for degassing (medium measure horizontal degassing of 300-m class), induction from degassing holes, fly ash sealing, sealed gas degassing, surveillance and control technologies and facilities. The recovered gas is to be supplied to the cities of Tiefa and Tieling as town gas, for which compressed gas feeding and controlling technologies and facilities will be introduced. This paper lists the gush-out quantity (1,000 Nm{sup 3}), the recovery quantity (1,000 Nm{sup 3}), the recovered gas concentration (%), the utilization quantity (1,000 Nm{sup 3}), and the utilization rate (%). The figures for the respective items before and after the implementation are 128366, 32949, 44.5, 7000, 5, 123500, 43890, 49.1, 39826, and 32. The quantity of gas gushing out at facings decreases in association with increase in the recovered gas quantity, whereas the gas concentration at facings in the Daixing mine in 2003 is estimated to decrease to 0.1%, contributing to safe mining operation. The test drilling for medium measure horizontal degassing expands the degassing assured scope per one test drilling seat, and can reduce the total test drilling length and construction amount. (NEDO)

Effect of method of N-application and modified urea on N-15 recovery by rice

International Nuclear Information System (INIS)

Soliman, S.M.; Abdelmonem, M.A.S.

1995-01-01

Rice is a very responsive crop to nitrogen fertilizer, but the efficiency of the applied N-fertilizer is low. Greenhouse experiment conducted to evaluate several methods to improve fertilizer efficiency and reduce N-losses in rice fields. N-15 labelled urea was applied to 10 kg soils in pots, urea was applied alone, with addition of two urease inhibitors (NBPT and HQ), with addition of nitrification inhibitor (DCD),or with the combination of both inhibitors. The fertilizers were applied either broadcast on soil surface or at depth of 8 cm below the surface. At maturity, plants were separated into grain and straw, dried and weighted. Soil and plant samples were analyzed for total N and N-15 excess. Both fertilizer placement and inhibitor application significantly increased straw and grain yield, as well as N-uptake. Nitrogen derived from fertilizer (%Ndff) was more than doubled, when urea was applied deep and in combination with inhibitors. Plant recovery of N-15 labelled urea ranged from 17% to 75% according to treatment. Regardless of inhibitors application, plant recovery was increased from 39% to 65% when urea was applied at depth of 8 cm. Approximately 2/3 of the applied urea (64%)was lost when urea was applied alone. Those losses were reduced down to 12% with deep placement and inhibitor application. The two management practices show significant effect on minimizing N-losses and increasing plant recovery. 1 fig., 3 tabs

Effect of method of N-application and modified urea on N-15 recovery by rice

Energy Technology Data Exchange (ETDEWEB)

Soliman, S M; Abdelmonem, M A.S. [Soil and Water Dept., Atomic Energy Auth., Cairo, (Egypt)

1995-10-01

Rice is a very responsive crop to nitrogen fertilizer, but the efficiency of the applied N-fertilizer is low. Greenhouse experiment conducted to evaluate several methods to improve fertilizer efficiency and reduce N-losses in rice fields. N-15 labelled urea was applied to 10 kg soils in pots, urea was applied alone, with addition of two urease inhibitors (NBPT and HQ), with addition of nitrification inhibitor (DCD),or with the combination of both inhibitors. The fertilizers were applied either broadcast on soil surface or at depth of 8 cm below the surface. At maturity, plants were separated into grain and straw, dried and weighted. Soil and plant samples were analyzed for total N and N-15 excess. Both fertilizer placement and inhibitor application significantly increased straw and grain yield, as well as N-uptake. Nitrogen derived from fertilizer (%Ndff) was more than doubled, when urea was applied deep and in combination with inhibitors. Plant recovery of N-15 labelled urea ranged from 17% to 75% according to treatment. Regardless of inhibitors application, plant recovery was increased from 39% to 65% when urea was applied at depth of 8 cm. Approximately 2/3 of the applied urea (64%)was lost when urea was applied alone. Those losses were reduced down to 12% with deep placement and inhibitor application. The two management practices show significant effect on minimizing N-losses and increasing plant recovery. 1 fig., 3 tabs.

Ranking oil sands bitumen recovery techniques

Energy Technology Data Exchange (ETDEWEB)

Lam, A.; Nobes, D.S.; Lipsett, M.G. [Alberta Univ., Edmonton, AB (Canada). Dept. of Mechanical Engineering

2009-07-01

The preference ranking organization method (PROMETHEE) was used to assess and rank 3 techniques for in situ bitumen recovery: (1) steam assisted gravity drainage; (2) vapour extraction (VAPEX); and (3) toe-to-heel air injection (THAI). The study used a business scenario where management-type indicators included potential production rates; estimated overall operating costs; energy consumption; facilities requirement; recovery efficiency; and energy loss. Amounts of carbon dioxide (CO{sub 2}) emissions were also considered, as well as the production depth, formation thickness, and API gravity of the produced bitumen. The study showed that THAI recovery methods had the most beneficial criteria weighting of the 3 processes, while SAGD was the least favourable choice. However, SAGD processes are the most widely used of the 3 processes, while THAI has only been demonstrated on a limited scale. It was concluded that the maturity of a technology should be weighted more heavily when using the PROMETHEE method. 8 refs., 2 tabs.

Aqueous methods for recovery of plutonium from pyrochemical residues

International Nuclear Information System (INIS)

Muscatello, A.C.; Killion, M.E.; Fisher, D.C.

1987-01-01

Studies of the recovery of plutonium from the pyrochemical residue salts from the Direct Oxide Reduction (DOR) and Electrorefining (ER) processes have shown that chloride anion exchange is useful and effective. Our previous studies have defined the operating limits for obtaining low level effluent plutonium losses on the order of 10 -3 g/l. The knowledge obtained in work on DOR salt was extended to ER salt and a process has been demonstrated to be feasible on a larger scale. Studies of oxalate precipitation of plutonium (III) from the eluat exhibit the expected losses to the filtrate as a function of the acidity. Two alternatives to chloride anion exchange, caustic leaching and direct oxalate precipitation are also shown to be feasible for the recovery of plutonium from ER salts. The results of studies of coprocessing DOR and ER residue salts to increase ER salt throughput and decrease HC1 requirements are also presented. The feasibility of coprocessing other pyrochemical residues, such as black salts, anode heel, and ER scrapeout will be discussed

Coping and recovery in whiplash-associated disorders

DEFF Research Database (Denmark)

Carroll, Linda J; Ferrari, Robert; Cassidy, John David

2014-01-01

Management Inventory, and neck pain recovery was assessed at each subsequent follow-up, using a 100 mm visual analogue scale (VAS). Disability was assessed at each follow-up using the Pain Disability Index (PDI). Pain recovery was defined as a VAS score of 0 to 10; disability recovery was defined as a PDI...... recovery, reductions in neck pain, and in disability. METHODS: A population-based prospective cohort study design was used to study 2986 adults with traffic-related WAD. Participants were assessed at baseline, 6 weeks, and 4, 8, and 12 months postinjury. Coping was measured at 6 weeks using the Pain...... score of 0 to 4. Data analysis used multivariable Cox proportional hazards models. RESULTS: Those using high versus low levels of passive coping at 6 weeks postinjury experienced 28% slower pain recovery and 43% slower disability recovery. Adjusted hazard rate ratios for pain recovery and disability...

The Temporal Effect of Training Utility Perceptions on Adopting a Trained Method: The Role of Perceived Organizational Support

Science.gov (United States)

Madera, Juan M.; Steele, Stacey T.; Beier, Margaret

2011-01-01

The current study examined the temporal effect of perceived training utility on adoption of a trained method and how perceived organizational support influences the relationship between perceived training utility perceptions and adoption of a trained method. With the use of a correlational-survey-based design, this longitudinal study required…

A socioeconomic assessment of Forest Service American Recovery and Reinvestment Act projects: eight case studies

Science.gov (United States)

Susan Charnley; Pamela J. Jakes; John Schelhas

2011-01-01

The American Recovery and Reinvestment Act of 2009 aimed to create jobs and jumpstart the economy while addressing the Nation’s social and environmental needs. The U.S. Department of Agriculture, Forest Service, received $1.15 billion in recovery funding to support projects in wildland fire management, capital improvement and maintenance, and biomass utilization. This...

Membrane assisted solvent extraction for rare earth element recovery

Science.gov (United States)

Bhave, Ramesh R.; Kim, Daejin; Peterson, Eric S.

2018-05-15

Systems and methods for the recovery of rare earth elements are provided. The systems and methods generally include membrane assisted solvent extraction using permeable hollow fibers having an immobilized organic phase within the pores of the hollow fibers. The permeable hollow fibers are generally in contact with an acidic aqueous feed on one side thereof and a strip solution on another side thereof. The systems and methods generally include the simultaneous extraction and stripping of rare earth elements as a continuous recovery process that is well suited for post-consumer products, end-of-life products, and other recovery sources of rare earth elements.

Trace and low concentration co2 removal methods and apparatus utilizing metal organic frameworks

KAUST Repository

Eddaoudi, Mohamed

2016-03-10

In general, this disclosure describes techniques for removing trace and low concentration CO2 from fluids using SIFSIX-n-M MOFs, wherein n is at least two and M is a metal. In some embodiments, the metal is zinc or copper. Embodiments include devices comprising SIFSIX-n-M MOFs for removing CO2 from fluids. In particular, embodiments relate to devices and methods utilizing SIFSIX-n-M MOFs for removing CO2 from fluids, wherein CO2 concentration is trace. Methods utilizing SIFSIX-n-M MOFs for removing CO2 from fluids can occur in confined spaces. SIFSIX-n-M MOFs can comprise bidentate organic ligands. In a specific embodiment, SIFSIX-n-M MOFs comprise pyrazine or dipryidilacetylene ligands.

Energy recovery from garden waste in a LCA perspective

DEFF Research Database (Denmark)

Naroznova, Irina; Møller, Jacob; Scheutz, Charlotte

2015-01-01

According to the common strategies regarding waste management and energy supply in EU countries, more efficient utilization of organic waste resources (including garden waste) with both nutrient and energy recovery is desired. Each of the most common treatments applied today – composting, direct...... use on land and incineration – only provides one of the two services. A technology ensuring both nutrient and energy utilization is anaerobic digestion (AD) that has become applicable for treatment of garden waste recently. In this study, life cycle assessment aimed to compare four garden waste...

Evaluation of remedial alternative of a LNAPL plume utilizing groundwater modeling

International Nuclear Information System (INIS)

Johnson, T.; Way, S.; Powell, G.

1997-01-01

The TIMES model was utilized to evaluate remedial options for a large LNAPL spill that was impacting the North Platte River in Glenrock, Wyoming. LNAPL was found discharging into the river from the adjoining alluvial aquifer. Subsequent investigations discovered an 18 hectare plume extended across the alluvium and into a sandstone bedrock outcrop to the south of the river. The TIMES model was used to estimate the LNAPL volume and to evaluate options for optimizing LNAPL recovery. Data collected from recovery and monitoring wells were used for model calibration. A LNAPL volume of 5.5 million L was estimated, over 3.0 million L of which is in the sandstone bedrock. An existing product recovery system was evaluated for its effectiveness. Three alternative recovery scenarios were also evaluated to aid in selecting the most cost-effective and efficient recovery system for the site. An active wellfield hydraulically upgradient of the existing recovery system was selected as most appropriate to augment the existing system in recovering LNAPL efficiently

Recovery and serious mental illness: a review of current clinical and research paradigms and future directions.

Science.gov (United States)

Leonhardt, Bethany L; Huling, Kelsey; Hamm, Jay A; Roe, David; Hasson-Ohayon, Ilanit; McLeod, Hamish J; Lysaker, Paul H

2017-11-01

Recovery from serious mental illness has historically not been considered a likely or even possible outcome. However, a range of evidence suggests the courses of SMI are heterogeneous with recovery being the most likely outcome. One barrier to studying recovery in SMI is that recovery has been operationalized in divergent and seemingly incompatible ways: as an objective outcome versus a subjective process. Areas covered: This paper offers a review of recovery as a subjective process and recovery as an objective outcome; contrasts methodologies utilized by each approach to assess recovery; reports rates and correlates of recovery; and explores the relationship between objective and subjective forms of recovery. Expert commentary: There are two commonalities of approaching recovery as a subjective process and an objective outcome: (i) the need to make meaning out of one's experiences to engage in either type of recovery and (ii) there exist many threats to engaging in meaning making that may impact the likelihood of moving toward recovery. We offer four clinical implications that stem from these two commonalities within a divided approach to the concept of recovery from SMI.

Functional recovery measures for spinal cord injury: an evidence-based review for clinical practice and research

DEFF Research Database (Denmark)

Anderson, K.; Aito, S.; Atkins, M.

2008-01-01

), the Functional Independence Measure (FIM), the Quadriplegia Index of Function (QIF), and the Spinal Cord Independence Measure (SCIM). The MBI and the QIF were found to have minimal evidence for validity, whereas the FIM and the SCIM were found to be reliable and valid. The MBI has little clinical utility for use......BACKGROUND/OBJECTIVE: The end goal of clinical care and clinical research involving spinal cord injury (SCI) is to improve the overall ability of persons living with SCI to function on a daily basis. Neurologic recovery does not always translate into functional recovery. Thus, sensitive outcome...... measures designed to assess functional status relevant to SCI are important to develop. METHOD: Evaluation of currently available SCI functional outcome measures by a multinational work group. RESULTS: The 4 measures that fit the prespecified inclusion criteria were the Modified Barthel Index (MBI...

Electro-gravimetric recovery of silver from aqueous solutions and its precursors

Directory of Open Access Journals (Sweden)

A. Shah,

2016-08-01

Full Text Available A simple electrolytic cell was used for electrochemical recovery of silver from aqueous solutions containing 100 mg/L Ag(I. Two different sets of electrodes were applied to find the enhanced recovery of silver. Rocks and ores samples were processed through fire assay method and acid digestion. A set of electrodes comprised of stainless steel anode and aluminum cathode gave maximum recovery (96.5% of silver. This simple, robust, environment friendly and highly sensitive method was effectively applied to various ores and rock samples. The developed method with slight modifications can also be applied for the recovery of other metals.

Muscle mass and physical recovery in ICU: innovations for targeting of nutrition and exercise.

Science.gov (United States)

Wischmeyer, Paul E; Puthucheary, Zudin; San Millán, Iñigo; Butz, Daniel; Grocott, Michael P W

2017-08-01

We have significantly improved hospital mortality from sepsis and critical illness in last 10 years; however, over this same period we have tripled the number of 'ICU survivors' going to rehabilitation. Furthermore, as up to half the deaths in the first year following ICU admission occur post-ICU discharge, it is unclear how many of these patients ever returned home or a meaningful quality of life. For those who do survive, recent data reveals many 'ICU survivors' will suffer significant functional impairment or post-ICU syndrome (PICS). Thus, new innovative metabolic and exercise interventions to address PICS are urgently needed. These should focus on optimal nutrition and lean body mass (LBM) assessment, targeted nutrition delivery, anabolic/anticatabolic strategies, and utilization of personalized exercise intervention techniques, such as utilized by elite athletes to optimize preparation and recovery from critical care. New data for novel LBM analysis technique such as computerized tomography scan and ultrasound analysis of LBM are available showing objective measures of LBM now becoming more practical for predicting metabolic reserve and effectiveness of nutrition/exercise interventions. 13C-Breath testing is a novel technique under study to predict infection earlier and predict over-feeding and under-feeding to target nutrition delivery. New technologies utilized routinely by athletes such as muscle glycogen ultrasound also show promise. Finally, the role of personalized cardiopulmonary exercise testing to target preoperative exercise optimization and post-ICU recovery are becoming reality. New innovative techniques are demonstrating promise to target recovery from PICS utilizing a combination of objective LBM and metabolic assessment, targeted nutrition interventions, personalized exercise interventions for prehabilitation and post-ICU recovery. These interventions should provide hope that we will soon begin to create more 'survivors' and fewer victim's post

Recovery strategies implemented by sport support staff of elite rugby players in South Africa

Directory of Open Access Journals (Sweden)

D.V. Van Wyk

2009-01-01

Full Text Available Objective: The main aim of this study was to determine strategies used toaccelerate recovery of elite rugby players after training and matches, asused by medical support staff of rugby teams in South A frica. A  secondaryaim was to focus on specifics of implementing ice/cold water immersion asrecovery strategy. Design: A  Questionnaire-based cross sectional descriptive survey was used.Setting and Participants: Most (n=58 of the medical support staff ofrugby teams (doctors, physiotherapists, biokineticists and fitness trainerswho attended the inaugural Rugby Medical A ssociation conference linked to the South A frican Sports MedicineA ssociation Conference in Pretoria (14-16th November, 2007 participated in the study. Results: Recovery strategies were utilized mostly after matches. Stretching and ice/cold water immersion were utilized the most (83%. More biokineticists and fitness trainers advocated the usage of stretching than their counter-parts (medical doctors and physiotherapists. Ice/Cold water immersion and A ctive Recovery were the top two ratedstrategies. A  summary of the details around implementation of ice/cold water therapy is shown (mean as utilized bythe subjects: (i The time to immersion after matches was 12±9 min; (ii The total duration of one immersion sessionwas 6±6 min; (iii 3 immersion sessions per average training week was utilized by subjects; (iv The average water temperature was 10±3 ºC.; (v Ice cubes were used most frequently to cool water for immersion sessions, and(vi plastic drums were mostly used as the container for water. Conclusion: In this survey the representative group of support staff provided insight to which strategies are utilizedin South A frican elite rugby teams to accelerate recovery of players after training and/or matches.

Maximal oil recovery by simultaneous condensation of alkane and steam

NARCIS (Netherlands)

Bruining, J.; Marchesin, D.

2007-01-01

This paper deals with the application of steam to enhance the recovery from petroleum reservoirs. We formulate a mathematical and numerical model that simulates coinjection of volatile oil with steam into a porous rock in a one-dimensional setting. We utilize the mathematical theory of conservation

Disaster Debris Recovery Database - Recovery

Data.gov (United States)

U.S. Environmental Protection Agency — The US EPA Disaster Debris Recovery Database (DDRD) promotes the proper recovery, recycling, and disposal of disaster debris for emergency responders at the federal,...

Recovery in soccer : part ii-recovery strategies.

Science.gov (United States)

Nédélec, Mathieu; McCall, Alan; Carling, Chris; Legall, Franck; Berthoin, Serge; Dupont, Gregory

2013-01-01

In the formerly published part I of this two-part review, we examined fatigue after soccer matchplay and recovery kinetics of physical performance, and cognitive, subjective and biological markers. To reduce the magnitude of fatigue and to accelerate the time to fully recover after completion, several recovery strategies are now used in professional soccer teams. During congested fixture schedules, recovery strategies are highly required to alleviate post-match fatigue, and then to regain performance faster and reduce the risk of injury. Fatigue following competition is multifactorial and mainly related to dehydration, glycogen depletion, muscle damage and mental fatigue. Recovery strategies should consequently be targeted against the major causes of fatigue. Strategies reviewed in part II of this article were nutritional intake, cold water immersion, sleeping, active recovery, stretching, compression garments, massage and electrical stimulation. Some strategies such as hydration, diet and sleep are effective in their ability to counteract the fatigue mechanisms. Providing milk drinks to players at the end of competition and a meal containing high-glycaemic index carbohydrate and protein within the hour following the match are effective in replenishing substrate stores and optimizing muscle-damage repair. Sleep is an essential part of recovery management. Sleep disturbance after a match is common and can negatively impact on the recovery process. Cold water immersion is effective during acute periods of match congestion in order to regain performance levels faster and repress the acute inflammatory process. Scientific evidence for other strategies reviewed in their ability to accelerate the return to the initial level of performance is still lacking. These include active recovery, stretching, compression garments, massage and electrical stimulation. While this does not mean that these strategies do not aid the recovery process, the protocols implemented up until

Rollback recovery with low overhead for fault tolerance in mobile ad hoc networks

Directory of Open Access Journals (Sweden)

Parmeet Kaur Jaggi

2015-10-01

Full Text Available Mobile ad hoc networks (MANETs have significantly enhanced the wireless networks by eliminating the need for any fixed infrastructure. Hence, these are increasingly being used for expanding the computing capacity of existing networks or for implementation of autonomous mobile computing Grids. However, the fragile nature of MANETs makes the constituent nodes susceptible to failures and the computing potential of these networks can be utilized only if they are fault tolerant. The technique of checkpointing based rollback recovery has been used effectively for fault tolerance in static and cellular mobile systems; yet, the implementation of existing protocols for MANETs is not straightforward. The paper presents a novel rollback recovery protocol for handling the failures of mobile nodes in a MANET using checkpointing and sender based message logging. The proposed protocol utilizes the routing protocol existing in the network for implementing a low overhead recovery mechanism. The presented recovery procedure at a node is completely domino-free and asynchronous. The protocol is resilient to the dynamic characteristics of the MANET; allowing a distributed application to be executed independently without access to any wired Grid or cellular network access points. We also present an algorithm to record a consistent global snapshot of the MANET.

Methods for assisting recovery of damaged brain and spinal cord and treating various diseases using arrays of x-ray microplanar beams

Energy Technology Data Exchange (ETDEWEB)

Dilmanian, F Avraham [Yaphank, NY; Anchel, David J [Rocky Point, NY; Gaudette, Glenn [Holden, MA; Romanelli, Pantaleo [Monteroduni, IT; Hainfeld, James [Shoreham, NY

2010-06-29

A method of assisting recovery of an injury site of the central nervous system (CNS) or treating a disease includes providing a therapeutic dose of X-ray radiation to a target volume through an array of parallel microplanar beams. The dose to treat CNS injury temporarily removes regeneration inhibitors from the irradiated site. Substantially unirradiated cells surviving between beams migrate to the in-beam portion and assist recovery. The dose may be staggered in fractions over sessions using angle-variable intersecting microbeam arrays (AVIMA). Additional doses are administered by varying the orientation of the beams. The method is enhanced by injecting stem cells into the injury site. One array or the AVIMA method is applied to ablate selected cells in a target volume associated with disease for palliative or curative effect. Atrial fibrillation is treated by irradiating the atrial wall to destroy myocardial cells while continuously rotating the subject.

Geochronology and geochemistry by nuclear tracks method: some utilization examples in geologic applied

International Nuclear Information System (INIS)

Poupeau, G.; Soliani Junior, E.

1988-01-01

This article discuss some applications of the 'nuclear tracks method' in geochronology, geochemistry and geophysic. In geochronology, after rapid presentation of the dating principles by 'Fission Track' and the kinds of geological events mensurable by this method, is showed some application in metallogeny and in petroleum geolocy. In geochemistry the 'fission tracks' method utilizations are related with mining prospecting and uranium prospecting. In geophysics an important application is the earthquake prevision, through the Ra 222 emanations continous control. (author) [pt

Biotechnological recovery of heavy metals from secondary sources-An overview

International Nuclear Information System (INIS)

Hoque, Md E.; Philip, Obbard J.

2011-01-01

The demand for heavy metals is ever increasing with the advance of the industrialized world, whereas worldwide reserves of high-grade ores are diminishing. However, there exist large stockpiles of low and lean grade ores that are yet to be exploited. In addition, heavy metals that are present in a spectrum of waste streams including mine drainage, industrial effluents, river sediments, electronic scraps and ashes are also available for recovery and utilization. Heavy metal recovery from low and lean grade ores using conventional techniques such as pyrometallurgy, etc. chemical metallurgy encompass several inherent constraints like, high energy and capital inputs, and high risk of secondary environmental pollution. As environmental regulations become ever more stringent, particularly regarding the disposal of toxic wastes, the costs for ensuring environmental protection will continue to rise. Therefore, there is a need to utilize more efficient technologies to recover heavy metals from secondary sources in order to minimize capital outlay, environmental impact and to respond to increased demand. Biohydrometallurgy, which exploits microbiological processes to recover heavy metal ions, is regarded as one of the most promising and revolutionary biotechnologies. The products of such processes are deposited in aqueous solution thereby rendering them to be more amenable to containment, treatment and recovery. On top of this, biohydrometallurgy can be conducted under mild conditions, usually without the use of any toxic chemicals. Consequently, the application of biohydrometallurgy in recovery of heavy metals from lean grade ores, and wastes, has made it an eco-friendly biotechnology for enhanced heavy metal production.

Biotechnological recovery of heavy metals from secondary sources-An overview

Energy Technology Data Exchange (ETDEWEB)

Hoque, Md E., E-mail: enamul.hoque@nottingham.edu.my [Department of Mechanical, Materials and Manufacturing Engineering, University of Nottingham Malaysia Campus, Jalan Broga, 43500 Semenyih, Selangor Darul Ehsan (Malaysia); Philip, Obbard J., E-mail: esejpo@nus.edu.sg [Division of Environmental Science and Engineering, National University of Singapore, 119260 (Singapore)

2011-03-12

The demand for heavy metals is ever increasing with the advance of the industrialized world, whereas worldwide reserves of high-grade ores are diminishing. However, there exist large stockpiles of low and lean grade ores that are yet to be exploited. In addition, heavy metals that are present in a spectrum of waste streams including mine drainage, industrial effluents, river sediments, electronic scraps and ashes are also available for recovery and utilization. Heavy metal recovery from low and lean grade ores using conventional techniques such as pyrometallurgy, etc. chemical metallurgy encompass several inherent constraints like, high energy and capital inputs, and high risk of secondary environmental pollution. As environmental regulations become ever more stringent, particularly regarding the disposal of toxic wastes, the costs for ensuring environmental protection will continue to rise. Therefore, there is a need to utilize more efficient technologies to recover heavy metals from secondary sources in order to minimize capital outlay, environmental impact and to respond to increased demand. Biohydrometallurgy, which exploits microbiological processes to recover heavy metal ions, is regarded as one of the most promising and revolutionary biotechnologies. The products of such processes are deposited in aqueous solution thereby rendering them to be more amenable to containment, treatment and recovery. On top of this, biohydrometallurgy can be conducted under mild conditions, usually without the use of any toxic chemicals. Consequently, the application of biohydrometallurgy in recovery of heavy metals from lean grade ores, and wastes, has made it an eco-friendly biotechnology for enhanced heavy metal production.

Using Landsat Spectral Indices in Time-Series to Assess Wildfire Disturbance and Recovery

Directory of Open Access Journals (Sweden)

Samuel Hislop

2018-03-01

Full Text Available Satellite earth observation is being increasingly used to monitor forests across the world. Freely available Landsat data stretching back four decades, coupled with advances in computer processing capabilities, has enabled new time-series techniques for analyzing forest change. Typically, these methods track individual pixel values over time, through the use of various spectral indices. This study examines the utility of eight spectral indices for characterizing fire disturbance and recovery in sclerophyll forests, in order to determine their relative merits in the context of Landsat time-series. Although existing research into Landsat indices is comprehensive, this study presents a new approach, by comparing the distributions of pre and post-fire pixels using Glass’s delta, for evaluating indices without the need of detailed field information. Our results show that in the sclerophyll forests of southeast Australia, common indices, such as the Normalized Difference Vegetation Index (NDVI and the Normalized Burn Ratio (NBR, both accurately capture wildfire disturbance in a pixel-based time-series approach, especially if images from soon after the disturbance are available. However, for tracking forest regrowth and recovery, indices, such as NDVI, which typically capture chlorophyll concentration or canopy ‘greenness’, are not as reliable, with values returning to pre-fire levels in 3–5 years. In comparison, indices that are more sensitive to forest moisture and structure, such as NBR, indicate much longer (8–10 years recovery timeframes. This finding is consistent with studies that were conducted in other forest types. We also demonstrate that additional information regarding forest condition, particularly in relation to recovery, can be extracted from less well known indices, such as NBR2, as well as textural indices incorporating spatial variance. With Landsat time-series gaining in popularity in recent years, it is critical to

4D CAD Based Method for Supporting Coordination of Urban Subsurface Utility Projects

NARCIS (Netherlands)

olde Scholtenhuis, Léon Luc; Hartmann, T.; Doree, Andries G.

Coordinators of inner city utility construction works face increasing difficulty in managing their projects due to tight physical restrictions, strict deadlines and growing stakeholder fragmentation. This paper therefore presents a 4D CAD based coordination method that supports project plan scoping,

Evaluation of a Residential Mental Health Recovery Service in North Queensland.

Science.gov (United States)

Heyeres, Marion; Kinchin, Irina; Whatley, Elise; Brophy, Lisa; Jago, Jon; Wintzloff, Thomas; Morton, Steve; Mosby, Vinitta; Gopalkrishnan, Narayan; Tsey, Komla

2018-01-01

Evidence shows that subacute mental health recovery occurs best when a person remains active within the community and fulfils meaningful and satisfying roles of their choosing. Several residential care services that incorporate these values have been established in Australia and overseas. This study describes (a) the development of an evaluation framework for a new subacute residential mental health recovery service in regional Australia and (b) reports on the formative evaluation outcomes. Continuous quality improvement and participatory research approaches informed all stages of the development of the evaluation framework. A program logic was established and subsequently tested for practicability. The resultant logic utilizes the Scottish Recovery Indicator 2 (SRI 2) service development tool, Individual Recovery Plans (IRPs), and the impact assessment of the service on psychiatric inpatient admissions (reported separately). Service strengths included a recovery-focused practice that identifies and addresses the basic needs of residents (consumers). The consumers of the service were encouraged to develop their own goals and self-manage their recovery plans. The staff of the service were identified as working effectively in the context of the recovery process; the staff were seen as supported and valued. Areas for improvement included more opportunities for self-management for residents and more feedback from residents and carers.

Implementing program-wide awareness about recovery in a large mental health and addictions program.

Science.gov (United States)

McVanel-Viney, Sarah; Younger, Jodi; Doyle, Winnie; Kirkpatrick, Helen

2006-01-01

St. Joseph's Healthcare Hamilton conceptualized a multi-step plan for implementing a recovery oriented service delivery approach within their Mental Health and Addictions Program. This brief report discusses the first phase of this plan which included building awareness of recovery utilizing Anthony's (2000) system standards to develop a needs assessment for managers and senior team members. The survey had three purposes: to increase managers' awareness about recovery; to allow managers to express concerns that they had with this paradigm; and to afford managers an opportunity to explore the ways in which their service was and was not operating in a recovery oriented way. Initiatives designed to build awareness throughout the program are discussed.

Measuring Recovery in Elite Rugby Players: The Brief Assessment of Mood, Endocrine Changes, and Power.

Science.gov (United States)

Shearer, David A; Kilduff, Liam P; Finn, Charlotte; Jones, Rhys M; Bracken, Richard M; Mellalieu, Stephen D; Owen, Nic; Crewther, Blair T; Cook, Christian J

2015-01-01

There is demand in applied sport settings to measure recovery briefly and accurately. Research indicates mood disturbance as the strongest psychological predictor of mental and physical recovery. The Brief Assessment of Mood (BAM) is a shortened version of the Profile of Mood States that can be completed in less than 30 s. The purpose of this study was to examine the BAM as a quick measure of mood in relation to recovery status in elite rugby players alongside established physiological markers of recovery. Using elite rugby union players (N = 12), this study examined the utility of BAM as an indicator of mental and physical recovery in elite athletes by exploring pattern change in mood disturbance, energy index, power output, cortisol, and testosterone 36 hr before and 12 hr, 36 hr, and 60 hr after a competitive rugby match. Repeated-measures multivariate analysis of variance indicated significant changes in all variables across the 4 time points (p < .05, η(2) range = .20-.48), concurrent with previous study findings. Although visual inspection of the graphs indicated that the pattern of change for mood disturbance and energy index mapped changes in all physiological variables, only a low correlation was observed for power output (r = - .34). Although BAM scores changed significantly over time in accordance with the hypotheses, further testing is required to confirm the utility of the BAM as a measure of recovery. The results indicate that the BAM could be used as 1 indicator of recovery status alongside other measures.

Recovery of uranium from alkaline ore (Tummalapalle) leach solution using novel precipitating method

International Nuclear Information System (INIS)

Biswas, Sujoy; Rupawate, V.H.; Hareendran, K.N.; Roy, S.B.; Chakravartty, J.K.

2014-01-01

The aim of present study is recovery of uranium from such ore leach solution containing 2 O 7 at pH ∼12.5. The average particle size of the MgU 2 O 7 particles was 20 micron and overall uranium recovery was 97%. The composition of final precipitate was characterized using XRD and surface morphology was studied using SEM

Ethanol production from food waste at high solids content with vacuum recovery technology.

Science.gov (United States)

Huang, Haibo; Qureshi, Nasib; Chen, Ming-Hsu; Liu, Wei; Singh, Vijay

2015-03-18

Ethanol production from food wastes does not only solve environmental issues but also provides renewable biofuels. This study investigated the feasibility of producing ethanol from food wastes at high solids content (35%, w/w). A vacuum recovery system was developed and applied to remove ethanol from fermentation broth to reduce yeast ethanol inhibition. A high concentration of ethanol (144 g/L) was produced by the conventional fermentation of food waste without a vacuum recovery system. When the vacuum recovery is applied to the fermentation process, the ethanol concentration in the fermentation broth was controlled below 100 g/L, thus reducing yeast ethanol inhibition. At the end of the conventional fermentation, the residual glucose in the fermentation broth was 5.7 g/L, indicating incomplete utilization of glucose, while the vacuum fermentation allowed for complete utilization of glucose. The ethanol yield for the vacuum fermentation was found to be 358 g/kg of food waste (dry basis), higher than that for the conventional fermentation at 327 g/kg of food waste (dry basis).

CO{sub 2} capture and utilization for enhanced oil recovery

Energy Technology Data Exchange (ETDEWEB)

Vilhelmsen, P.J.; Well, W. van; Nielsen, Charles [DONG Energy Generation, Fredericia (Denmark); Harrar, W.; Reffstrup, J. [DONG Energy Exploration and Production, Hoersholm (Denmark)

2007-05-15

CO{sub 2} is an international theme and the cap-and-trade systems under implementation will lead to significant alterations in the energy market and in the energy system altogether. A possible technical step to reduce atmospheric emissions is CO{sub 2} capture and the utilisation of the CO{sub 2} for Enhanced Oil Recovery (EOR). CO{sub 2} capture is to some extent a know technology but has not yet been optimised and commercialised for power plant utilisation. Correspondingly CO{sub 2} utilisation for EOR is a known method in other areas of the world where the reservoir conditions are different from those of the North Sea. For several years Elsam and Energi E2, part of DONG Energy, have worked on reducing CO{sub 2} emissions through increased efficiency at the coal-fired power plants, and this work has now been extended to also include capture and utilisation of CO{sub 2}. DONG E and P within DONG Energy has started work on the utilisation of CO{sub 2} for EOR at the company's fields in the North Sea. Based on DONG Energy's interest in working through the whole value chain from power plants to EOR utilisation in the North Sea, this paper describes our experience with CO{sub 2} capture at the trial plant CASTOR at Esbjerg power plant and the actual work of investigating and preparing the pilot test of CO{sub 2} for EOR in the North Sea. The paper also illustrates the perspectives of retrofitting the existing fleet of super critical coal-fired power plants close to the North Sea with CO{sub 2} capture and the utilisation of the CO{sub 2} for EOR in the North Sea. DONG Energy's perspective is that CO{sub 2} for EOR can contribute to materialising the vision that the central power plant can be developed into an energy refinery. The development work presented will be carried out in cooperation with leading international players and Danish universities and knowledge centres Technical University of Denmark (DTU), The Danish Geotechnical Institute (GEO) and Geological

Functional Recovery Measures for Spinal Cord Injury: An Evidence-Based Review for Clinical Practice and Research

Science.gov (United States)

Anderson, Kim; Aito, Sergio; Atkins, Michal; Biering-Sørensen, Fin; Charlifue, Susan; Curt, Armin; Ditunno, John; Glass, Clive; Marino, Ralph; Marshall, Ruth; Mulcahey, Mary Jane; Post, Marcel; Savic, Gordana; Scivoletto, Giorgio; Catz, Amiram

2008-01-01

Background/Objective: The end goal of clinical care and clinical research involving spinal cord injury (SCI) is to improve the overall ability of persons living with SCI to function on a daily basis. Neurologic recovery does not always translate into functional recovery. Thus, sensitive outcome measures designed to assess functional status relevant to SCI are important to develop. Method: Evaluation of currently available SCI functional outcome measures by a multinational work group. Results: The 4 measures that fit the prespecified inclusion criteria were the Modified Barthel Index (MBI), the Functional Independence Measure (FIM), the Quadriplegia Index of Function (QIF), and the Spinal Cord Independence Measure (SCIM). The MBI and the QIF were found to have minimal evidence for validity, whereas the FIM and the SCIM were found to be reliable and valid. The MBI has little clinical utility for use in the SCI population. Likewise, the FIM applies mainly when measuring burden of care, which is not necessarily a reflection of functional recovery. The QIF is useful for measuring functional recovery but only in a subpopulation of people with SCI, and substantial validity data are still required. The SCIM is the only functional recovery outcome measure designed specifically for SCI. Conclusions: The multinational work group recommends that the latest version of the SCIM (SCIM III) continue to be refined and validated and subsequently implemented worldwide as the primary functional recovery outcome measure for SCI. The QIF may continue to be developed and validated for use as a supplemental tool for the nonambulatory tetraplegic population. PMID:18581660

Recovery of crown mass for energy with whole-tree skidding methods; Puupolttoaineen tuottaminen kokopuujuontomenetelmillae

Energy Technology Data Exchange (ETDEWEB)

Nousiainen, I [Finntech Ltd Oy, Jyvaeskylae (Finland); Vesisenaho, T [VTT Energy, Jyvaeskylae (Finland)

1997-12-31

The main aim of the project `Recovery of crown mass for energy with whole-tree skidding methods` was to develop the integrated harvesting method of wood raw material and wood fuel based on whole-tree skidding. The developed method gives also the possibility to deliver to sawmills raw material in the form of log section. In the harvesting chain under development whole-trees are felled and bunched with a normal one-grip harvester. The whole-trees are skidded to the roadside by a forwarder equipped with a clam bunk. At the roadside the trees are delimbed and cut with the one-grip harvester used for felling and bunching. According to the results of the field tests the harvesting costs of logging residues are in certain final cutting conditions even under 10 FIM/m{sup 3}, when the average stem size is over 0,500 m{sup 3}. In the developed method felling and bunching of whole trees with the one-grip harvester and skidding of whole-trees with the clam skidder succeeded well. The problems of the method concentrate on delimbing and bucking of whole-trees in landing site

Recovery of crown mass for energy with whole-tree skidding methods; Puupolttoaineen tuottaminen kokopuujuontomenetelmillae

Energy Technology Data Exchange (ETDEWEB)

Nousiainen, I. [Finntech Ltd Oy, Jyvaeskylae (Finland); Vesisenaho, T. [VTT Energy, Jyvaeskylae (Finland)

1996-12-31

The main aim of the project `Recovery of crown mass for energy with whole-tree skidding methods` was to develop the integrated harvesting method of wood raw material and wood fuel based on whole-tree skidding. The developed method gives also the possibility to deliver to sawmills raw material in the form of log section. In the harvesting chain under development whole-trees are felled and bunched with a normal one-grip harvester. The whole-trees are skidded to the roadside by a forwarder equipped with a clam bunk. At the roadside the trees are delimbed and cut with the one-grip harvester used for felling and bunching. According to the results of the field tests the harvesting costs of logging residues are in certain final cutting conditions even under 10 FIM/m{sup 3}, when the average stem size is over 0,500 m{sup 3}. In the developed method felling and bunching of whole trees with the one-grip harvester and skidding of whole-trees with the clam skidder succeeded well. The problems of the method concentrate on delimbing and bucking of whole-trees in landing site

Do sampling methods differ in their utility for ecological monitoring? Comparison of line-point intercept, grid-point intercept, and ocular estimate methods

Science.gov (United States)

This study compared the utility of three sampling methods for ecological monitoring based on: interchangeability of data (rank correlations), precision (coefficient of variation), cost (minutes/transect), and potential of each method to generate multiple indicators. Species richness and foliar cover...

EUV tools: hydrogen gas purification and recovery strategies

Science.gov (United States)

Landoni, Cristian; Succi, Marco; Applegarth, Chuck; Riddle Vogt, Sarah

2015-03-01

The technological challenges that have been overcome to make extreme ultraviolet lithography (EUV) a reality have been enormous1. This vacuum driven technology poses significant purity challenges for the gases employed for purging and cleaning the scanner EUV chamber and source. Hydrogen, nitrogen, argon and ultra-high purity compressed dry air (UHPCDA) are the most common gases utilized at the scanner and source level. Purity requirements are tighter than for previous technology node tools. In addition, specifically for hydrogen, EUV tool users are facing not only gas purity challenges but also the need for safe disposal of the hydrogen at the tool outlet. Recovery, reuse or recycling strategies could mitigate the disposal process and reduce the overall tool cost of operation. This paper will review the types of purification technologies that are currently available to generate high purity hydrogen suitable for EUV applications. Advantages and disadvantages of each purification technology will be presented. Guidelines on how to select the most appropriate technology for each application and experimental conditions will be presented. A discussion of the most common approaches utilized at the facility level to operate EUV tools along with possible hydrogen recovery strategies will also be reported.

Esterification Reaction Utilizing Sense of Smell and Eyesight for Conversion and Catalyst Recovery Monitoring

Science.gov (United States)

Janssens, Nikki; Wee, Lik H.; Martens, Johan A.

2014-01-01

The esterification reaction of salicylic acid with ethanol is performed in presence of dissolved 12-tungstophosphoric Brønsted-Lowry acid catalyst, a Keggin-type polyoxometalate (POM). The monitoring of the reaction with smell and the recovery of the catalyst with sight is presented. Formation of the sweet-scented ester is apparent from the smell.…

Development a recovery method of 13I from the 23'5U fission products

International Nuclear Information System (INIS)

Bignardi, Aline M.T.; Osso Junior, Joao Alberto

2013-01-01

13I is a iodine radioisotope widely used in nuclear medicine that can be used either for diagnostic or for treatment due to its physical decay by β- and its high emission of rays-γ. It is produced at IPEN through the irradiation of TeO 2 targets in the IEA-R1 nuclear reactor. There is also the possibility produced it by the fission of 235 U. The aim of this work is to develop a recovery method of 13I in the production process of 99 Mo through the route of acid dissolution of 235 U targets, with the quality to be used in Nuclear Medicine. 13I finds itself in two stages of the process, either in the gaseous produced in the acid dissolution of metallic U targets and the smallest part in solution. In this work was studied the recovery of 131 in these two stages. Several materials were used for the capture and recovery of 13I at the two phases of the process. Anionic cartridges, Ag cartridges, anion exchange resin, activated charcoal columns and AgI precipitation were tested. Solutions with 13 '1I in 0.1 mol.L -1 NaOH were percolated through the materials and the eluted solutions were analyzed in a dose calibrator. Among all the tests that were executed, at first, the anion exchange resin and AgI precipitation have showed the best retention result (100%). The results of elution have varied according to the material, the activated charcoal presented a elution yield between 70% and 82% At first, it is possible to conclude that anion exchange resin and AgI precipitation show better results for 13I retention and the column and activated charcoal have a great potential for the elution of 131 in the right chemical state. (author)

Taguchi optimization: Case study of gold recovery from amalgamation tailing by using froth flotation method

Science.gov (United States)

Sudibyo, Aji, B. B.; Sumardi, S.; Mufakir, F. R.; Junaidi, A.; Nurjaman, F.; Karna, Aziza, Aulia

2017-01-01

Gold amalgamation process was widely used to treat gold ore. This process produces the tailing or amalgamation solid waste, which still contains gold at 8-9 ppm. Froth flotation is one of the promising methods to beneficiate gold from this tailing. However, this process requires optimal conditions which depends on the type of raw material. In this study, Taguchi method was used to optimize the optimum conditions of the froth flotation process. The Taguchi optimization shows that the gold recovery was strongly influenced by the particle size which is the best particle size at 150 mesh followed by the Potassium amyl xanthate concentration, pH and pine oil concentration at 1133.98, 4535.92 and 68.04 gr/ton amalgamation tailing, respectively.

Simultaneous heat integration and techno-economic optimization of Organic Rankine Cycle (ORC) for multiple waste heat stream recovery

International Nuclear Information System (INIS)

Yu, Haoshui; Eason, John; Biegler, Lorenz T.; Feng, Xiao

2017-01-01

In the past decades, the Organic Rankine Cycle (ORC) has become a promising technology for low and medium temperature energy utilization. In refineries, there are usually multiple waste heat streams to be recovered. From a safety and controllability perspective, using an intermedium (hot water) to recover waste heat before releasing heat to the ORC system is more favorable than direct integration. The mass flowrate of the intermediate hot water stream determines the amount of waste heat recovered and the final hot water temperature affects the thermal efficiency of ORC. Both, in turn, exert great influence on the power output. Therefore, the hot water mass flowrate is a critical decision variable for the optimal design of the system. This study develops a model for techno-economic optimization of an ORC with simultaneous heat recovery and capital cost optimization. The ORC is modeled using rigorous thermodynamics with the concept of state points. The task of waste heat recovery using the hot water intermedium is modeled using the Duran-Grossmann model for simultaneous heat integration and process optimization. The combined model determines the optimal design of an ORC that recovers multiple waste heat streams in a large scale background process using an intermediate heat transfer stream. In particular, the model determines the optimal heat recovery approach temperature (HRAT), the utility load of the background process, and the optimal operating conditions of the ORC simultaneously. The effectiveness of this method is demonstrated with a case study that uses a refinery as the background process. Sensitivity of the optimal solution to the parameters (electricity price, utility cost) is quantified in this paper. - Highlights: • A new model for Organic Rankine cycle design optimization is presented. • Process heat integration and ORC are considered simultaneously. • Rigorous equation oriented models of the ORC are used for accurate results. • Impact of working

Double-label autoradiographic deoxyglucose method for sequential measurement of regional cerebral glucose utilization

Energy Technology Data Exchange (ETDEWEB)

Redies, C; Diksic, M; Evans, A C; Gjedde, A; Yamamoto, Y L

1987-08-01

A new double-label autoradiographic glucose analog method for the sequential measurement of altered regional cerebral metabolic rates for glucose in the same animal is presented. This method is based on the sequential injection of two boluses of glucose tracer labeled with two different isotopes (short-lived /sup 18/F and long-lived /sup 3/H, respectively). An operational equation is derived which allows the determination of glucose utilization for the time period before the injection of the second tracer; this equation corrects for accumulation and loss of the first tracer from the metabolic pool occurring after the injection of the second tracer. An error analysis of this operational equation is performed. The double-label deoxyglucose method is validated in the primary somatosensory (''barrel'') cortex of the anesthetized rat. Two different rows of whiskers were stimulated sequentially in each rat; the two periods of stimulation were each preceded by an injection of glucose tracer. After decapitation, dried brain slices were first exposed, in direct contact, to standard X-ray film and then to uncoated, ''tritium-sensitive'' film. Results show that the double-label deoxyglucose method proposed in this paper allows the quantification and complete separation of glucose utilization patterns elicited by two different stimulations sequentially applied in the same animal.

Three methods to monitor utilization of healthcare services by the poor

Directory of Open Access Journals (Sweden)

Urni Farhana

2009-08-01

Full Text Available Abstract Background Achieving equity by way of improving the condition of the economically poor or otherwise disadvantaged is among the core goals of contemporary development paradigm. This places importance on monitoring outcome indicators among the poor. National surveys allow disaggregation of outcomes by socioeconomic status at national level and do not have statistical adequacy to provide estimates for lower level administrative units. This limits the utility of these data for programme managers to know how well particular services are reaching the poor at the lowest level. Managers are thus left without a tool for monitoring results for the poor at lower levels. This paper demonstrates that with some extra efforts community and facility based data at the lower level can be used to monitor utilization of healthcare services by the poor. Methods Data used in this paper came from two sources- Chakaria Health and Demographic Surveillance System (HDSS of ICDDR,B and from a special study conducted during 2006 among patients attending the public and private health facilities in Chakaria, Bangladesh. The outcome variables included use of skilled attendants for delivery and use of facilities. Rate-ratio, rate-difference, concentration index, benefit incidence ratio, sequential sampling, and Lot Quality Assurance Sampling were used to assess how pro-poor is the use of skilled attendants for delivery and healthcare facilities. Findings Poor are using skilled attendants for delivery far less than the better offs. Government health service facilities are used more than the private facilities by the poor. Benefit incidence analysis and sequential sampling techniques could assess the situation realistically which can be used for monitoring utilization of services by poor. The visual display of the findings makes both these methods attractive. LQAS, on the other hand, requires small fixed sample and always enables decision making. Conclusion With some

Three methods to monitor utilization of healthcare services by the poor

Science.gov (United States)

Bhuiya, Abbas; Hanifi, SMA; Urni, Farhana; Mahmood, Shehrin Shaila

2009-01-01

Background Achieving equity by way of improving the condition of the economically poor or otherwise disadvantaged is among the core goals of contemporary development paradigm. This places importance on monitoring outcome indicators among the poor. National surveys allow disaggregation of outcomes by socioeconomic status at national level and do not have statistical adequacy to provide estimates for lower level administrative units. This limits the utility of these data for programme managers to know how well particular services are reaching the poor at the lowest level. Managers are thus left without a tool for monitoring results for the poor at lower levels. This paper demonstrates that with some extra efforts community and facility based data at the lower level can be used to monitor utilization of healthcare services by the poor. Methods Data used in this paper came from two sources- Chakaria Health and Demographic Surveillance System (HDSS) of ICDDR,B and from a special study conducted during 2006 among patients attending the public and private health facilities in Chakaria, Bangladesh. The outcome variables included use of skilled attendants for delivery and use of facilities. Rate-ratio, rate-difference, concentration index, benefit incidence ratio, sequential sampling, and Lot Quality Assurance Sampling were used to assess how pro-poor is the use of skilled attendants for delivery and healthcare facilities. Findings Poor are using skilled attendants for delivery far less than the better offs. Government health service facilities are used more than the private facilities by the poor. Benefit incidence analysis and sequential sampling techniques could assess the situation realistically which can be used for monitoring utilization of services by poor. The visual display of the findings makes both these methods attractive. LQAS, on the other hand, requires small fixed sample and always enables decision making. Conclusion With some extra efforts monitoring of the

The effect of DNA recovery on the subsequent quality of latent fingermarks.

Science.gov (United States)

Fieldhouse, Sarah; Oravcova, Eliska; Walton-Williams, Laura

2016-10-01

The recovery of DNA and fingermark evidence from the same site can be problematic on account of potential contamination from fingermark visualisation techniques, and/or the destructive capability of the DNA recovery method. Forensic investigators are therefore often required to choose which evidence type to recover, or to recover both evidence types from different sites. Research typically documents the effects of fingermark visualisation techniques on the subsequent recovery of DNA, whereas this research has investigated the effects of DNA recovery on the quality of subsequently recovered latent fingermarks. Eccrine rich, sebaceous rich, and 'normal' latent fingermarks were deposited onto five substrates: glass; aluminium; textured plastic; varnished wood; photocopier paper and aged from 4h to 4 weeks. Approximately half of the control fingermarks were developed without DNA recovery on all substrates. The remaining samples were subjected to one of five DNA recovery methods prior to fingermark development. Pre and post DNA recovered fingermarks were graded for quality, and AFIS correlations scores were obtained and analysed for statistically significant differences using Wilcoxon Signed Rank tests and Friedman tests. All of the DNA recovery methods reduced the quality of latent fingermarks on glass surfaces. Flocked swabs and gel lifts were the least destructive DNA recovery methods on the remaining surfaces, except for aluminium sheet metal. The quality of latent fingermarks deposited onto glossed wood and textured plastic and paper were less affected by dry swabbing. Wet swabbing and tape lifting were very damaging methods of DNA recovery. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Enhanced oil recovery methods studied by gamma tracer scanning at simulated reservoir conditions

International Nuclear Information System (INIS)

Eriksen, D.O.; Haugen, O.B.; Bjornstad, T.

2009-01-01

During recovery (production) of hydrocarbons pressure is maintained by injecting prepared sea water and recycled gas (lean gas) into dedicated injection wells. In one well at the Snorre field in the North Sea the injected gas was recycled too fast to enable support of pressure and squeezing of oil. To plug this high-permeable area the operator wanted to inject foam as a test of its possibilities to decrease gas permeability. As part of the project laboratory tests were included. In these tests we could for the first time map the foam inside the sandstone sample at simulated reservoir conditions. The tracers used were 22 Na + for the γ-scanning of the aqueous brine, tritiated water for permeability measurements, and 35 S-labeled organic sulfonic acid of the same compound as the surfactant. This method resulted in a 'negative' mapping of the foam, i.e. measurements of the absence or exclusion of the aqueous phase by the foam. This method was new and showed that radiotracer-based γ-scanning could give much more accurate measurements of the position of the foam than the standard method using measurements of pressure drops over parts of the core. (author)

[Series: Utilization of Differential Equations and Methods for Solving Them in Medical Physics (1)].

Science.gov (United States)

Murase, Kenya

2014-01-01

Utilization of differential equations and methods for solving them in medical physics are presented. First, the basic concept and the kinds of differential equations were overviewed. Second, separable differential equations and well-known first-order and second-order differential equations were introduced, and the methods for solving them were described together with several examples. In the next issue, the symbolic and series expansion methods for solving differential equations will be mainly introduced.

Maximization of revenues for power sales from a solid waste resources recovery facility

Energy Technology Data Exchange (ETDEWEB)

1991-12-01

The report discusses the actual implementation of the best alternative in selling electrical power generated by an existing waste-to-energy facility, the Metro-Dade County Resources Recovery Plant. After the plant processes and extracts various products out of the municipal solid waste, it burns it to produce electrical power. The price for buying power to satisfy the internal needs of our Resources Recovery Facility (RRF) is substantially higher than the power price for selling electricity to any other entity. Therefore, without any further analysis, it was decided to first satisfy those internal needs and then export the excess power. Various alternatives were thoroughly explored as to what to do with the excess power. Selling power to the power utilities or utilizing the power in other facilities were the primary options.

To belong, contribute, and hope: first stage development of a measure of social recovery.

Science.gov (United States)

Marino, Casadi Khaki

2015-04-01

Recovery from mental health challenges is beginning to be explored as an inherently social process. There is a need to measure social recovery. Targeted measures would be utilized in needs assessment, service delivery, and program evaluation. This paper reports on the first stage of development of a social recovery measure. Explore the social aspects of recovery as reported by individuals with lived experience. A qualitative study using thematic analysis of data from focus groups with 41 individuals in recovery. Three meta-themes of social recovery emerged: community, self-concept, and capacities. Each theme contained a number of sub-themes concerned with a sense of belonging, inherent acceptability of the self, and ability to cope with mental distress and engage socially. Study participants clearly spoke to common human needs to belong, contribute, and have hope for one's future. Findings converged with results of consumer-led research that emphasize the importance of overcoming the impact of illness on the self and social context.

Plant-Scale Concentration Column Designs for SHINE Target Solution Utilizing AG 1 Anion Exchange Resin

Energy Technology Data Exchange (ETDEWEB)

Stepinski, Dominique C. [Argonne National Lab. (ANL), Argonne, IL (United States); Vandegrift, G. F. [Argonne National Lab. (ANL), Argonne, IL (United States)

2015-09-30

Argonne is assisting SHINE Medical Technologies (SHINE) in their efforts to develop SHINE, an accelerator-driven process that will utilize a uranyl-sulfate solution for the production of fission product Mo-99. An integral part of the process is the development of a column for the separation and recovery of Mo-99, followed by a concentration column to reduce the product volume from 15-25 L to <1 L. Argonne has collected data from batch studies and breakthrough column experiments to utilize the VERSE (Versatile Reaction Separation) simulation program (Purdue University) to design plant-scale product recovery and concentration processes.

Perceptions about recovery needs and drug-avoidance recovery behaviors among youth in substance abuse treatment.

Science.gov (United States)

Gonzales, Rachel; Anglin, M Douglas; Glik, Deborah C; Zavalza, Christina

2013-01-01

This study used mixed methods to explore youth attitudes about recovery-related needs and important drug-avoidance behaviors after treatment. Focus groups were conducted with 118 substance using youth in treatment (four residential and 10 outpatient settings) throughout Los Angeles County. The average age was 17.4 (SD = 2.9); 78.3% were male, 66.1% Latino; and most were in treatment for primary marijuana (40.9%) or methamphetamine (30.4%) abuse. Quantitatve results from the drug-avoidance activity survey identified the following factors youth rated as important to their recovery after treatment: lifestyle improvement activities (95.7%); changing personal drug behaviors (89.6%); drug environment/culture change activities (82.5%); with the least important being therapeutic activities (78.5%). Qualitative findings from focus groups that asked what youth think are important for recovery programs to address after treatment revealed the following four areas: (1) recovery promotion to developmentally appropriate activities (95%); (2) facilitating the use of coping skills to deal with stress (85%); (3) offering alternative recovery support options (not just abstinence only) (75%); and (4) continuing to provide substance use education (65%). Findings highlight essential aspects of recovery in terms of need and drug-avoidance behaviors considered important to youth in treatment. Such information will help to better address clinical and recovery support models aimed at relapse prevention to ensure that the perceived problems of substance-abusing youth are adequately met.

Recovery-Oriented Practice in Mental Health Inpatient Settings

DEFF Research Database (Denmark)

Waldemar, Anna Kristine; Arnfred, Sidse M; Petersen, Lone

2016-01-01

OBJECTIVE: Implementation of recovery-oriented practice has proven to be challenging, and little is known about the extent to which recovery-oriented principles are integrated into mental health inpatient settings. This review of the literature examined the extent to which a recovery......-oriented approach is an integrated part of mental health inpatient settings. METHODS: A systematic search (2000-2014) identified quantitative and qualitative studies that made explicit reference to the concept of recovery and that were conducted in adult mental health inpatient settings or that used informants from......, the United States, Australia, and Ireland were included. The results highlight the limited number of studies of recovery-oriented practice in mental health inpatient settings and the limited extent to which such an approach is integrated into these settings. Findings raise the question of whether recovery...

Refined reservoir description to maximize oil recovery

International Nuclear Information System (INIS)

Flewitt, W.E.

1975-01-01

To assure maximized oil recovery from older pools, reservoir description has been advanced by fully integrating original open-hole logs and the recently introduced interpretive techniques made available through cased-hole wireline saturation logs. A refined reservoir description utilizing normalized original wireline porosity logs has been completed in the Judy Creek Beaverhill Lake ''A'' Pool, a reefal carbonate pool with current potential productivity of 100,000 BOPD and 188 active wells. Continuous porosity was documented within a reef rim and cap while discontinuous porous lenses characterized an interior lagoon. With the use of pulsed neutron logs and production data a separate water front and pressure response was recognized within discrete environmental units. The refined reservoir description aided in reservoir simulation model studies and quantifying pool performance. A pattern water flood has now replaced the original peripheral bottom water drive to maximize oil recovery

Three approaches for estimating recovery factors in carbon dioxide enhanced oil recovery

Science.gov (United States)

Verma, Mahendra K.

2017-07-17

PrefaceThe Energy Independence and Security Act of 2007 authorized the U.S. Geological Survey (USGS) to conduct a national assessment of geologic storage resources for carbon dioxide (CO2) and requested the USGS to estimate the “potential volumes of oil and gas recoverable by injection and sequestration of industrial carbon dioxide in potential sequestration formations” (42 U.S.C. 17271(b)(4)). Geologic CO2 sequestration associated with enhanced oil recovery (EOR) using CO2 in existing hydrocarbon reservoirs has the potential to increase the U.S. hydrocarbon recoverable resource. The objective of this report is to provide detailed information on three approaches that can be used to calculate the incremental recovery factors for CO2-EOR. Therefore, the contents of this report could form an integral part of an assessment methodology that can be used to assess the sedimentary basins of the United States for the hydrocarbon recovery potential using CO2-EOR methods in conventional oil reservoirs.

Exploration and mining. Predevelopment studies for mine methane management and utilization

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

With an objective to reduce influence on the environment, studies have been performed on recovery and utilization of methane gas discharged from mines, and on simulation of discharge of methane gas from coal being mined. The studies included data collection of the Hunter Valley regional coal and gas resources, a review of gas recovery technologies and practice, Wambo site data collection and geological characterization, rock tests for compressive strength and shear strength, testing of a CSIRO/CMTE automatic analysis method, and preparation of a preliminary 3D Vulcan model. The result of the studies during this year reveals that the lower Hunter Coalfield contains 1,324 Mt recoverable reserve and 1,033 Mt marketable reserve; the area contains 83.96 billion m{sup 3} in-situ gas; gas content in the Arrowfield and Bowfield seams at the Wambo mine is around 8 m{sup 3}/t, and 10 m{sup 3}/t, and a typical gas composition is 70% CH{sub 4} and 30% CO2; and the gas content increases with depth. (NEDO)

Membrane Technology for the Recovery of Lignin: A Review

Directory of Open Access Journals (Sweden)

Daniel Humpert

2016-09-01

Full Text Available Utilization of renewable resources is becoming increasingly important, and only sustainable processes that convert such resources into useful products can achieve environmentally beneficial economic growth. Wastewater from the pulp and paper industry is an unutilized resource offering the potential to recover valuable products such as lignin, pigments, and water [1]. The recovery of lignin is particularly important because it has many applications, and membrane technology has been investigated as the basis of innovative recovery solutions. The concentration of lignin can be increased from 62 to 285 g∙L−1 using membranes and the recovered lignin is extremely pure. Membrane technology is also scalable and adaptable to different waste liquors from the pulp and paper industry.

Membrane Technology for the Recovery of Lignin: A Review

Science.gov (United States)

Humpert, Daniel; Ebrahimi, Mehrdad; Czermak, Peter

2016-01-01

Utilization of renewable resources is becoming increasingly important, and only sustainable processes that convert such resources into useful products can achieve environmentally beneficial economic growth. Wastewater from the pulp and paper industry is an unutilized resource offering the potential to recover valuable products such as lignin, pigments, and water [1]. The recovery of lignin is particularly important because it has many applications, and membrane technology has been investigated as the basis of innovative recovery solutions. The concentration of lignin can be increased from 62 to 285 g∙L−1 using membranes and the recovered lignin is extremely pure. Membrane technology is also scalable and adaptable to different waste liquors from the pulp and paper industry. PMID:27608047

Uranium recovery from AVLIS slag

International Nuclear Information System (INIS)

D'Agostino, A.E.; Mycroft, J.R.; Oliver, A.J.; Schneider, P.G.; Richardson, K.L.

2000-01-01

Uranium metal for the Atomic Vapor Laser Isotope Separation (AVLIS) project was to have been produced by the magnesiothermic reduction of uranium tetrafluoride. The other product from this reaction is a magnesium fluoride slag, which contains fine and entrained natural uranium as metal and oxide. Recovery of the uranium through conventional mill leaching would not give a magnesium residue free of uranium but to achieve more complete uranium recovery requires the destruction of the magnesium fluoride matrix and liberation of the entrapped uranium. Alternate methods of carrying out such treatments and the potential for recovery of other valuable byproducts were examined. Based on the process flowsheets, a number of economic assessments were performed, conclusions were drawn and the preferred processing alternatives were identified. (author)

Actinide recovery from waste and low-grade sources

International Nuclear Information System (INIS)

Navratil, J.D.; Schulz, W.W.

1982-01-01

Actinide and nuclear fuel cycle operations generate a variety of process waste streams. New methods are needed to remove and recover actinides. More interest is also being expressed in recovering uranium from oceans, phosphoric acid, and other low grade sources. To meet the need for an up-to-date status report in the area of actinide recovery from waste and low grade sources, these papers were brought together. The papers provide an authoritative, in-depth coverage of an important area of nuclear and industrial and engineering chemistry which cover the following topics: uranium recovery from oceans and phosphoric acid; recovery of actinides from solids and liquid wastes; plutonium scrap recovery technology; and other new developments in actinide recovery processes

Comparison of the different methods for the recovery of suspended matter from estuarine waters: deposition, filtration and centrifugation

Energy Technology Data Exchange (ETDEWEB)

Etcheber, H; Jouanneau, J M

1980-12-01

The advantages and disadvantages of three methods used to recover heavy metals from estuarine waters are compared. Deposition, filtration, and centrifugation were used on samples from the Gironde estuary of France. Recovery by deposition is satisfactory in cases of flocculation and high turbidity. Centrifugation is reliable for the determination of several elements in zones of low turbidity. (12 references, 4 tables)

Cognitive performance and aphasia recovery.

Science.gov (United States)

Fonseca, José; Raposo, Ana; Martins, Isabel Pavão

2018-03-01

Objectives This study assessed cognitive performance of subjects with aphasia during the acute stage of stroke and evaluated how such performance relates to recovery at 3 months. Materials & methods Patients with aphasia following a left hemisphere stroke were evaluated during the first (baseline) and the fourth-month post onset. Assessment comprised non-verbal tests of attention/processing speed (Symbol Search, Cancelation Task), executive functioning (Matrix Reasoning, Tower of Hanoi, Clock Drawing, Motor Initiative), semantic (Camel and Cactus Test), episodic and immediate memory (Memory for Faces Test, 5 Objects Memory Test, and Spatial Span. Recovery was measured by the Token Test score at 3 months. The impact of baseline performance on recovery was evaluated by logistic regression adjusting for age, education, severity of aphasia and the Alberta Stroke Program Early CT (ASPECT) score. Results Thirty-nine subjects (with a mean of 66.5 ± 10.6 years of age, 17 men) were included. Average baseline cognitive performance was within normal range in all tests except in memory tests (semantic, episodic and immediate memory) for which scores were ≤-1.5sd. Subjects with poor aphasia recovery (N = 27) were older and had fewer years of formal education but had identical ASPECT score compared to those with favorable recovery. Considering each test individually, the score obtained on the Matrix Reasoning test was the only one to predict aphasia recovery (Exp(B)=24.085 p = 0.038). Conclusions The Matrix Reasoning Test may contribute to predict aphasia recovery. Cognitive performance is a measure of network disruption but may also indicate the availability of recovery strategies.

Acoustic Radiation Force-Induced Creep-Recovery (ARFICR): A Noninvasive Method to Characterize Tissue Viscoelasticity.

Science.gov (United States)

Amador Carrascal, Carolina; Chen, Shigao; Urban, Matthew W; Greenleaf, James F

2018-01-01

Ultrasound shear wave elastography is a promising noninvasive, low cost, and clinically viable tool for liver fibrosis staging. Current shear wave imaging technologies on clinical ultrasound scanners ignore shear wave dispersion and use a single group velocity measured over the shear wave bandwidth to estimate tissue elasticity. The center frequency and bandwidth of shear waves induced by acoustic radiation force depend on the ultrasound push beam (push duration, -number, etc.) and the viscoelasticity of the medium, and therefore are different across scanners from different vendors. As a result, scanners from different vendors may give different tissue elasticity measurements within the same patient. Various methods have been proposed to evaluate shear wave dispersion to better estimate tissue viscoelasticity. A rheological model such as the Kelvin-Voigt model is typically fitted to the shear wave dispersion to solve for the elasticity and viscosity of tissue. However, these rheological models impose strong assumptions about frequency dependence of elasticity and viscosity. Here, we propose a new method called Acoustic Radiation Force Induced Creep-Recovery (ARFICR) capable of quantifying rheological model-independent measurements of elasticity and viscosity for more robust tissue health assessment. In ARFICR, the creep-recovery time signal at the focus of the push beam is used to calculate the relative elasticity and viscosity (scaled by an unknown constant) over a wide frequency range. Shear waves generated during the ARFICR measurement are also detected and used to calculate the shear wave velocity at its center frequency, which is then used to calibrate the relative elasticity and viscosity to absolute elasticity and viscosity. In this paper, finite-element method simulations and experiments in tissue mimicking phantoms are used to validate and characterize the extent of viscoelastic quantification of ARFICR. The results suggest that ARFICR can measure tissue

Waste heat recovery for offshore applications

DEFF Research Database (Denmark)

Pierobon, Leonardo; Kandepu, Rambabu; Haglind, Fredrik

2012-01-01

vary in the range 20-30%. There are several technologies available for onshore gas turbines (and low/medium heat sources) to convert the waste heat into electricity. For offshore applications it is not economical and practical to have a steam bottoming cycle to increase the efficiency of electricity...... production, due to low gas turbine outlet temperature, space and weight restrictions and the need for make-up water. A more promising option for use offshore is organic Rankine cycles (ORC). Moreover, several oil and gas platforms are equipped with waste heat recovery units to recover a part of the thermal...... energy in the gas turbine off-gas using heat exchangers, and the recovered thermal energy acts as heat source for some of the heat loads on the platform. The amount of the recovered thermal energy depends on the heat loads and thus the full potential of waste heat recovery units may not be utilized...

Quality of Recovery Evaluation of the Protection Schemes for Fiber-Wireless Access Networks

Science.gov (United States)

Fu, Minglei; Chai, Zhicheng; Le, Zichun

2016-03-01

With the rapid development of fiber-wireless (FiWi) access network, the protection schemes have got more and more attention due to the risk of huge data loss when failures occur. However, there are few studies on the performance evaluation of the FiWi protection schemes by the unified evaluation criterion. In this paper, quality of recovery (QoR) method was adopted to evaluate the performance of three typical protection schemes (MPMC scheme, OBOF scheme and RPMF scheme) against the segment-level failure in FiWi access network. The QoR models of the three schemes were derived in terms of availability, quality of backup path, recovery time and redundancy. To compare the performance of the three protection schemes comprehensively, five different classes of network services such as emergency service, prioritized elastic service, conversational service, etc. were utilized by means of assigning different QoR weights. Simulation results showed that, for the most service cases, RPMF scheme was proved to be the best solution to enhance the survivability when planning the FiWi access network.

Improving ATLAS computing resource utilization with HammerCloud

CERN Document Server

Schovancova, Jaroslava; The ATLAS collaboration

2018-01-01

HammerCloud is a framework to commission, test, and benchmark ATLAS computing resources and components of various distributed systems with realistic full-chain experiment workflows. HammerCloud contributes to ATLAS Distributed Computing (ADC) Operations and automation efforts, providing the automated resource exclusion and recovery tools, that help re-focus operational manpower to areas which have yet to be automated, and improve utilization of available computing resources. We present recent evolution of the auto-exclusion/recovery tools: faster inclusion of new resources in testing machinery, machine learning algorithms for anomaly detection, categorized resources as master vs. slave for the purpose of blacklisting, and a tool for auto-exclusion/recovery of resources triggered by Event Service job failures that is being extended to other workflows besides the Event Service. We describe how HammerCloud helped commissioning various concepts and components of distributed systems: simplified configuration of qu...

Potential of wheat bran to promote indigenous microbial enhanced oil recovery.

Science.gov (United States)

Zhan, Yali; Wang, Qinghong; Chen, Chunmao; Kim, Jung Bong; Zhang, Hongdan; Yoza, Brandon A; Li, Qing X

2017-06-01

Microbial enhanced oil recovery (MEOR) is an emerging oil extraction technology that utilizes microorganisms to facilitate recovery of crude oil in depleted petroleum reservoirs. In the present study, effects of wheat bran utilization were investigated on stimulation of indigenous MEOR. Biostimulation conditions were optimized with the response surface methodology. The co-application of wheat bran with KNO 3 and NH 4 H 2 PO 4 significantly promoted indigenous MEOR (IMEOR) and exhibited sequential aerobic (O-), facultative (A n -) and anaerobic (A 0 -) metabolic stages. The surface tension of fermented broth decreased by approximately 35%, and the crude oil was highly emulsified. Microbial community structure varied largely among and in different IMEOR metabolic stages. Pseudomonas sp., Citrobacter sp., and uncultured Burkholderia sp. dominated the O-, A n - and early A 0 -stages. Bacillus sp., Achromobacter sp., Rhizobiales sp., Alcaligenes sp. and Clostridium sp. dominated the later A 0 -stage. This study illustrated occurrences of microbial community succession driven by wheat bran stimulation and its industrial potential.

Improved methods for urinary atrazine mercapturate analysis-Assessment of an enzyme-linked immunosorbent assay (ELISA) and a novel liquid chromatography-mass spectrometry (LC-MS) method utilizing online solid phase extraction (SPE)

International Nuclear Information System (INIS)

Koivunen, Marja E.; Dettmer, Katja; Vermeulen, Roel; Bakke, Berit; Gee, Shirley J.; Hammock, Bruce D.

2006-01-01

Elimination of interfering substances in urine by solid phase extraction (SPE) prior to analysis resulted in 10-fold improvement in the sensitivity of atrazine mercapturate (AM) enzyme-linked immunosorbent assay (ELISA) compared to previous reports. Of the two tested SPE systems, Oasis[reg] HLB and MCX, the mixed-mode MCX gave good recoveries (82%) of AM in spiked samples measured by ELISA, whereas the reverse-phase HLB phase was not compatible with the immunochemical method. At relatively high concentrations of urinary AM (>20 ng mL -1 ), sample dilution was effective enough for the elimination of interfering substances. The new liquid chromatography-mass spectrometry (LC-MS) method developed for AM utilizes online-SPE with Oasis[reg] HLB, column switching and a stable-isotope internal standard. The limit of quantification (0.05 ng mL -1 ) indicates improved sensitivity compared with most previously published LC-MS methods for AM. Validation of all three methods, LC-MS, ELISA + SPE and ELISA + dilution with spiked urine samples showed good correlation between the known and measured concentrations with R 2 values of 0.996, 0.957 and 0.961, respectively. When a set (n = 70 plus 12 blind duplicates) of urine samples from farmers exposed to atrazine was analyzed, there was a good agreement (R 2 = 0.917) between the log normalized data obtained by ELISA + SPE and LC-MS. High correlation among the data obtained by the two tested methods and the LC-MS method by the Center of Disease Control and Prevention (CDC), together with low variability among the blind duplicates, suggests that both methods reported here would be suitable for the analysis of urinary AM as a biomarker for human exposure of atrazine

Net lost revenue adjustment (NLRA) mechanisms for utility DSM programs

International Nuclear Information System (INIS)

Baxter, L.W.

1995-01-01

We examine the experiences that states and utilities are having with the NLRA approach. Contrary to concerns raised by some industry analysts, our results indicate the NLRA is a feasible approach to the lost-revenue disincentive. Seven of the 10 states we studied report no substantial problems with their approach. We observe several conditions linked to effective NLRA implementation and, for those states reporting problems, conditions linked to implementation difficulties. Finally, observed changes in utility-investment behavior occur after implementation of DSM rate reforms, which include deployment of NLRA mechanisms. We find that utilities in states with lost revenue recovery invest more than twice as much in DSM as do utilities in other states. (Author)

A single method for recovery and concentration of enteric viruses and bacteria from fresh-cut vegetables.

Science.gov (United States)

Sánchez, G; Elizaquível, P; Aznar, R

2012-01-03

Fresh-cut vegetables are prone to be contaminated with foodborne pathogens during growth, harvest, transport and further processing and handling. As most of these products are generally eaten raw or mildly treated, there is an increase in the number of outbreaks caused by viruses and bacteria associated with fresh vegetables. Foodborne pathogens are usually present at very low levels and have to be concentrated (i.e. viruses) or enriched (i.e. bacteria) to enhance their detection. With this aim, a rapid concentration method has been developed for the simultaneous recovery of hepatitis A virus (HAV), norovirus (NV), murine norovirus (MNV) as a surrogate for NV, Escherichia coli O157:H7, Listeria monocytogenes and Salmonella enterica. Initial experiments focused on evaluating the elution conditions suitable for virus release from vegetables. Finally, elution with buffered peptone water (BPW), using a Pulsifier, and concentration by polyethylene glycol (PEG) precipitation were the methods selected for the elution and concentration of both, enteric viruses and bacteria, from three different types of fresh-cut vegetables by quantitative PCR (qPCR) using specific primers. The average recoveries from inoculated parsley, spinach and salad, were ca. 9.2%, 43.5%, and 20.7% for NV, MNV, and HAV, respectively. Detection limits were 132 RT-PCR units (PCRU), 1.5 50% tissue culture infectious dose (TCID₅₀), and 6.6 TCID₅₀ for NV, MNV, and HAV, respectively. This protocol resulted in average recoveries of 57.4%, 64.5% and 64.6% in three vegetables for E. coli O157:H7, L. monocytogenes and Salmonella with corresponding detection limits of 10³, 10² and 10³ CFU/g, respectively. Based on these results, it can be concluded that the procedure herein is suitable to recover, detect and quantify enteric viruses and foodborne pathogenic bacteria within 5 h and can be applied for the simultaneous detection of both types of foodborne pathogens in fresh-cut vegetables. Copyright �

Optimisation of decontamination method and influence of culture media on the recovery of Mycobacterium avium subspecies paratuberculosis from spiked water sediments.

Science.gov (United States)

Aboagye, G; Rowe, M T

2018-07-01

The recovery of Mycobacterium avium subspecies paratuberculosis (Map) from the environment can be a laborious process - owing to Map being fastidious, its low number, and also high numbers of other microbial populations in such settings. Protocols i.e. filtration, decontamination and modified elution were devised to recover Map from spiked water sediments. Three culture media: Herrold's Egg Yolk Media (HEYM), Middlebrook 7H10 (M-7H10) and Bactec 12B were then employed to grow the organism following its elution. In the sterile sediment samples the recovery of Map was significant between the time of exposure for each of HEYM and M-7H10, and insignificant between both media (P < 0.05). However, in the non-sterile sediment samples, the HEYM grew other background microflora including moulds at all the times of exposure whilst 4 h followed by M-7H10 culture yielded Map colonies without any background microflora. Using sterile samples only for the Bactec 12B, the recovery of Map decreased as time of exposure increased. Based on these findings, M-7H10 should be considered for the recovery of Map from the natural environment including water sediments where the recovery of diverse microbial species remains a challenge. Map is a robust pathogen that abides in the environment. In water treatment operations, Map associates with floccules and other particulate matter including sediments. It is also a fastidious organism, and its detection and recovery from the water environment is a laborious process and can be misleading within the abundance of other mycobacterial species owing to their close resemblance in phylogenetic traits. In the absence of a reliable recovery method, Map continues to pose public health risks through biofilm in household water tanks, hence the need for the development of a reliable recovery protocol to monitor the presence of Map in water systems in order to curtail its public health risks. Copyright © 2018 Elsevier B.V. All rights reserved.

Recovery from schizophrenia and the recovery model.

Science.gov (United States)

Warner, Richard

2009-07-01

The recovery model refers to subjective experiences of optimism, empowerment and interpersonal support, and to a focus on collaborative treatment approaches, finding productive roles for user/consumers, peer support and reducing stigma. The model is influencing service development around the world. This review will assess whether optimism about outcome from serious mental illness and other tenets of the recovery model are borne out by recent research. Remission of symptoms has been precisely defined, but the definition of 'recovery' is a more diffuse concept that includes such factors as being productive and functioning independently. Recent research and a large, earlier body of data suggest that optimism about outcome from schizophrenia is justified. A substantial proportion of people with the illness will recover completely and many more will regain good social functioning. Outcome is better for people in the developing world. Mortality for people with schizophrenia is increasing but is lower in the developing world. Working appears to help people recover from schizophrenia, and recent advances in vocational rehabilitation have been shown to be effective in countries with differing economies and labor markets. A growing body of research supports the concept that empowerment is an important component of the recovery process. Key tenets of the recovery model - optimism about recovery from schizophrenia, the importance of access to employment and the value of empowerment of user/consumers in the recovery process - are supported by the scientific research. Attempts to reduce the internalized stigma of mental illness should enhance the recovery process.

Utilization of net energy analysis as a method of evaluating energy systems

International Nuclear Information System (INIS)

Lee, Gi Won; Cho, Joo Hyun; Hah, Yung Joon

1994-01-01

It can be said that the upturn of Korean nuclear power program started in early 70's while future plants for the construction of new nuclear power plants virtually came to a halt in United States since the late 70's. It is projected that power plant systems from combination of nuclear and coal fired types might shift to all coal fired type in U.S., considering the current U.S. trend of construction on the new plants. However, with the depletion of natural resources, it may be desirable to understand the utilization of two competitive utility technologies in terms of invested energy. Presented in this paper is a method of comparing two energy systems in terms of energy investment and a brief result from energy economic analysis of nuclear power plant and coal fired steam power plant to illustrate the methodology. The method of comparison is Net Energy Analysis (NEA). In doing so, Input-Output Analysis (lOA) among industries and commodities is done. Using these information, net energy ratios are calculated and compared. Although NEA does not offer conclusive solution, it can be used as a screening process in decision making

Proficiency feasibility of multi-walled carbon nanotubes in the presence of polymeric surfactant on enhanced oil recovery

Science.gov (United States)

Nezhad, Javad Razavi; Jafari, Arezou; Abdollahi, Mahdi

2018-01-01

Enhanced heavy oil recovery methods are widely utilized to increase oil recovery. For this purpose, polymer and surfactant flooding have been used extensively. Recently, polymeric surfactant flooding has become an attractive alternative to sole polymer flooding due to their capability of providing an increase in solution viscosity and a decrease in interfacial tension, which are both beneficial for efficiency of the process. Applying nanoparticles as an additive to polymer solutions is a method to improve viscosity and alter rock wettability. Therefore, in this research, multi-walled carbon nanotube (MWCNT) was mixed with a polymeric surfactant of polyacrylamide-graft-lignin copolymer (PAM-g-L) synthesized via radical grafting reaction. Moreover, several solutions with different concentrations of nanoparticles with PAM-g-L were prepared. The solutions were injected into a micromodel to evaluate the PAM-g-L flooding efficiency in presence of the multi-walled carbon nanotubes. The results of micromodel flooding showed that increasing MWCNT concentration results in lower sweep efficiencies; and consequently, oil production will decrease. Therefore, MWCNT along with PAM-g-L has an unacceptable performance in enhanced heavy oil recovery. But data of wettability tests revealed that MWCNT can change the wettability from oil-wet to water-wet. In addition, the combination of the PAM-g-L and MWCNT in a solution will cause more water-wet condition.

Uranium accompanying recovery from copper ores

International Nuclear Information System (INIS)

Golynko, Z.Sh.; Laskorin, B.N.

1981-01-01

In the search for new raw material sources for nuclear power engineering a review of the technique of uranium accompaning recovery from copper ores reprocessing products in some countries is presented. In the USA a sorption method of uranium extraction by means of strongly basic ion exchange resins from solutions upon copper case- hardening with subsequent extraction from eluates by solutions of tertiary amines is realized. Elution is realized with sulphuric acid. In South Africa an extraction reprocessing of gravitational concentrate extracted from copper sulphide flotation tailings is organized. In India the uranium extraction from copper ores flotation enrichment tailings is organized on a commerical scale. Presented are data on the scale of uranium recovery, various conditions of its recovery as well as block diagrams of the processes. It is shown that copper ores become an additional source of uranium recovery [ru

SPECT imaging with resolution recovery

International Nuclear Information System (INIS)

Bronnikov, A. V.

2011-01-01

Single-photon emission computed tomography (SPECT) is a method of choice for imaging spatial distributions of radioisotopes. Many applications of this method are found in nuclear industry, medicine, and biomedical research. We study mathematical modeling of a micro-SPECT system by using a point-spread function (PSF) and implement an OSEM-based iterative algorithm for image reconstruction with resolution recovery. Unlike other known implementations of the OSEM algorithm, we apply en efficient computation scheme based on a useful approximation of the PSF, which ensures relatively fast computations. The proposed approach can be applied with the data acquired with any type of collimators, including parallel-beam fan-beam, cone-beam and pinhole collimators. Experimental results obtained with a micro SPECT system demonstrate high efficiency of resolution recovery. (authors)

Energetic recovery from LNG gasification plant : cold energy utilization in agro-alimentary industry

International Nuclear Information System (INIS)

Messineo, A.; Panno, D.

2009-01-01

It is known how the complete gasification of liquefied natural gas (LNG) can return about 230 kWh/t of energy. Nevertheless out of 51 gasification plants in the world, only 31 of them are equipped with systems for the partial recovery of the available energy. At the moment most of these plants mainly produce electric energy; however the employment of the cold energy results very interesting, in fact, it can be recovered for agrofood transformation and conservation as well as for some loops in the cold chain. Cold energy at low temperatures requires high amounts of mechanical energy and it unavoidably increases as the required temperature diminishes. Cold energy recovery from LNG gasification would allow considerable energy and economic savings to these applications, as well as environmental benefits due to the reduction of climate-changing gas emissions. The task of this work is to assess the possibility to create around a gasification plant an industrial site for firms working on the transformation and conservation of agrofood products locally grown. The cold recovered from gasification would be distributed to those firms through an opportune liquid Co 2 network distribution capable of supplying the cold to the different facilities. A LNG gasification plant in a highly agricultural zone in Sicily would increase the worth of the agrofood production, lower transformation and conservation costs when compared to the traditional systems and bring economic and environmental benefits to the interested areas. [it

Fabric defect detection based on visual saliency using deep feature and low-rank recovery

Science.gov (United States)

Liu, Zhoufeng; Wang, Baorui; Li, Chunlei; Li, Bicao; Dong, Yan

2018-04-01

Fabric defect detection plays an important role in improving the quality of fabric product. In this paper, a novel fabric defect detection method based on visual saliency using deep feature and low-rank recovery was proposed. First, unsupervised training is carried out by the initial network parameters based on MNIST large datasets. The supervised fine-tuning of fabric image library based on Convolutional Neural Networks (CNNs) is implemented, and then more accurate deep neural network model is generated. Second, the fabric images are uniformly divided into the image block with the same size, then we extract their multi-layer deep features using the trained deep network. Thereafter, all the extracted features are concentrated into a feature matrix. Third, low-rank matrix recovery is adopted to divide the feature matrix into the low-rank matrix which indicates the background and the sparse matrix which indicates the salient defect. In the end, the iterative optimal threshold segmentation algorithm is utilized to segment the saliency maps generated by the sparse matrix to locate the fabric defect area. Experimental results demonstrate that the feature extracted by CNN is more suitable for characterizing the fabric texture than the traditional LBP, HOG and other hand-crafted features extraction method, and the proposed method can accurately detect the defect regions of various fabric defects, even for the image with complex texture.

Study of fuel cell powerplant with heat recovery

Science.gov (United States)

King, J. M.; Grasso, A. P.; Clausi, J. V.

1975-01-01

It was shown that heat can be recovered from fuel cell power plants by replacing the air-cooled heat exchangers in present designs with units which transfer the heat to the integrated utility system. Energy availability for a 40-kW power plant was studied and showed that the total usable energy at rated power represents 84 percent of the fuel lower heating value. The effects of design variables on heat availability proved to be small. Design requirements were established for the heat recovery heat exchangers, including measurement of the characteristics of two candidate fuel cell coolants after exposure to fuel cell operating conditions. A heat exchanger test program was defined to assess fouling and other characteristics of fuel cell heat exchangers needed to confirm heat exchanger designs for heat recovery.

Energy minimization strategies and renewable energy utilization for desalination: a review.

Science.gov (United States)

Subramani, Arun; Badruzzaman, Mohammad; Oppenheimer, Joan; Jacangelo, Joseph G

2011-02-01

Energy is a significant cost in the economics of desalinating waters, but water scarcity is driving the rapid expansion in global installed capacity of desalination facilities. Conventional fossil fuels have been utilized as their main energy source, but recent concerns over greenhouse gas (GHG) emissions have promoted global development and implementation of energy minimization strategies and cleaner energy supplies. In this paper, a comprehensive review of energy minimization strategies for membrane-based desalination processes and utilization of lower GHG emission renewable energy resources is presented. The review covers the utilization of energy efficient design, high efficiency pumping, energy recovery devices, advanced membrane materials (nanocomposite, nanotube, and biomimetic), innovative technologies (forward osmosis, ion concentration polarization, and capacitive deionization), and renewable energy resources (solar, wind, and geothermal). Utilization of energy efficient design combined with high efficiency pumping and energy recovery devices have proven effective in full-scale applications. Integration of advanced membrane materials and innovative technologies for desalination show promise but lack long-term operational data. Implementation of renewable energy resources depends upon geography-specific abundance, a feasible means of handling renewable energy power intermittency, and solving technological and economic scale-up and permitting issues. Copyright © 2011 Elsevier Ltd. All rights reserved.

An exploratory study of lead recovery in lead-acid battery lifecycle in US market: An evidence-based approach

International Nuclear Information System (INIS)

Genaidy, A.M.; Sequeira, R.; Tolaymat, T.; Kohler, J.; Rinder, M.

2008-01-01

Background: This research examines lead recovery and recycling in lead-acid batteries (LAB) which account for 88% of US lead consumption. We explore strategies to maximize lead recovery and recycling in the LAB lifecycle. Currently, there is limited information on recycling rates for LAB in the published literature and is derived from a single source. Therefore, its recycling efforts in the US has been unclear so as to determine the maximum opportunities for metal recovery and recycling in the face of significant demands for LAB particularly in the auto industry. Objectives: The research utilizes an evidence-based approach to: (1) determine recycling rates for lead recovery in the LAB product lifecycle for the US market; and (2) quantify and identify opportunities where lead recovery and recycling can be improved. Methods: A comprehensive electronic search of the published literature was conducted to gather information on different LAB recycling models and actual data used to calculate recycling rates based on product lifecycle for the US market to identify strategies for increasing lead recovery and recycling. Results: The electronic search yielded five models for calculating LAB recycling rates. The description of evidence was documented for each model. Furthermore, an integrated model was developed to identify and quantify the maximum opportunities for lead recovery and recycling. Results showed that recycling rates declined during the period spanning from 1999 to 2006. Opportunities were identified for recovery and recycling of lead in the LAB product lifecycle. Concluding remarks: One can deduce the following from the analyses undertaken in this report: (1) lead recovery and recycling has been stable between 1999 and 2006; (2) lead consumption has increased at an annual rate of 2.25%, thus, the values derived in this study for opportunities dealing with lead recovery and recycling underestimate the amount of lead in scrap and waste generated; and (3) the

Energy recovery as a key technology for future mobility

Energy Technology Data Exchange (ETDEWEB)

Zellbeck, Hans; Risse, Silvio [Technische Univ. Dresden (Germany). Lehrstuhl fuer Verbrennungsmotoren

2011-07-01

Internal and external combustion engines in both stationary and mobile applications represent an essential, basic module for a functioning economy and society. In ensuring mobility worldwide by land and by sea, the combustion engine plays the dominant role. Customer requirements to be fulfilled are manifold. Accordingly a downward trend in the demand for or indeed the abandonment of the combustion engine in personal or freight transport is in the near future unforeseeable. With regard to the continuously increasing need for mobility subject to limited resources and rising environmental consciousness, the combustion engine and the means to improve its efficiency and sustainability are under intensive investigation. Along with the application of CO{sub 2}-neutral fuels, improvements in the system itself will be valuable to its future. More specifically, compared to many other techniques the recovery of energy losses resulting from the operation of these engines promises a very high degree of optimization. An overview of the current and predicted number of combustion engines in both stationary and mobile applications is given at the beginning of the paper. Furthermore, a differentiation between personal and freight traffic must be made since there is not only a difference in their respective power requirements but also in their lifecycles. The energy losses through exhaust gases and coolants, for example, are quantified and rated in terms of their capabilities on the basis of certain fields of application and utilization profiles. With regard to additional specific boundary conditions, various concepts ranging from recuperation in theory to actual recovery in practice under conditions approximating actual production are analysed in different application scenarios for their efficiency, ecological benefit, and economy. Retroactive or synergistic effects which may follow from their integration into the complete system are considered precisely with the help of examples

Cost analysis and ecological benefits of environmental recovery methodologies in bauxite mining

OpenAIRE

Guimarães,João Carlos Costa; Barros,Dalmo Arantes de; Pereira,José Aldo Alves; Silva,Rossi Allan; Oliveira,Antonio Donizette de; Borges,Luís Antônio Coimbra

2013-01-01

This work analyzed and compared three methods of environmental recovery in bauxite mining commonly used in Poços de Caldas Plateau, MG, by means of recovery costs and ecological benefits. Earnings and costs data of environmental recovery activities were obtained for the areas that belonged to the Companhia Geral de Minas – CGM, on properties sited in the city of Poços de Caldas, MG. The amount of costs of these activities was used to compare the recovery methods by updating them monetarily to...

Numerical Simulations for Enhanced Methane Recovery from Gas Hydrate Accumulations by Utilizing CO2 Sequestration

Science.gov (United States)

Sridhara, Prathyusha

In 2013, the International Energy Outlook (EIA, 2013) projected that global energy demand will grow by 56% between 2010 and 2040. Despite strong growth in renewable energy supplies, much of this growth is expected to be met by fossil fuels. Concerns ranging from greenhouse gas emissions and energy security are spawning new interests for other sources of energy including renewable and unconventional fossil fuel such as shale gas and oil as well as gas hydrates. The production methods as well as long-term reservoir behavior of gas hydrate deposits have been under extensive investigation. Reservoir simulators can be used to predict the production potentials of hydrate formations and to determine which technique results in enhanced gas recovery. In this work, a new simulation tool, Mix3HydrateResSim (Mix3HRS), which accounts for complex thermodynamics of multi-component hydrate phase comprised of varying hydrate solid crystal structure, is used to perform the CO2-assisted production technique simulations from CH4 hydrate accumulations. The simulator is one among very few reservoir simulators which can simulate the process of CH4 substitution by CO2 (and N2 ) in the hydrate lattice. Natural gas hydrate deposits around the globe are categorized into three different classes based on the characteristics of the geological sediments present in contact with the hydrate bearing deposits. Amongst these, the Class 2 hydrate accumulations predominantly confirmed in the permafrost and along seashore, are characterized by a mobile aqueous phase underneath a hydrate bearing sediment. The exploitation of such gas hydrate deposits results in release of large amounts of water due to the presence of permeable water-saturated sediments encompassing the hydrate deposits, thus lowering the produced gas rates. In this study, a suite of numerical simulation scenarios with varied complexity are considered which aimed at understanding the underlying changes in physical, thermodynamic and

Recovery of vanadium oxide

International Nuclear Information System (INIS)

Bates, C.P.; Clark, N.E.

1985-01-01

This invention relates to the recovery of vanadium oxide from molten metal. The invention provides a method for recovering vanadium oxide from molten metal, which includes passing oxygen and at least one coolant gas or shroud into the molten metal by way of at least one elongate lance. The invention also provides an arrangement for the recovery of vanadium oxide from molten metal, which includes at least one elongate lance extending into the molten metal. The lance is provided with at least one elongate bore extending therethrough. Means are provided to allow at least oxygen and at least one coolant gas to pass through the lance and into the molten metal

Further development of recovery boiler; Soodakattilan kehitystyoe

Energy Technology Data Exchange (ETDEWEB)

Janka, K.; Siiskonen, P.; Sundstroem, K. [Tampella Power Oy, Tampere (Finland)] [and others

1996-12-01

The global model of a recovery boiler was further developed. The aim is to be able to model the velocity, temperature and concentration fields in a boiler. At this moment the model includes submodels for: droplet drying, pyrolysis, char burning, gas burning and for droplet trajectory. The preliminary study of NO{sub x} and fly ash behaviour in a boiler was carried out. The study concerning flow field in the superheater area was carried out a 2-dimensional case in which the inflow parameters were taken from global model of a recovery boiler. Further the prediction methods of fouling in a recovery boiler were developed based on theoretical calculations of smelting behaviour of multicomponent mixtures and measurements at operating recovery boilers. (author)

Descubriendo la Lectura: An Application of Reading Recovery in Spanish. [Final Report.

Science.gov (United States)

Escamilla, Kathy

A study investigated the utility of a set of Spanish-language instructional materials, "Decsubriendo la Lectura," in compensatory or remedial literacy education for Spanish-speaking elementary students. The reading recovery approach, used with English-speaking first-graders, was adapted for Spanish. Program development included…

Lignin recovery. A resource to value

International Nuclear Information System (INIS)

Zimbardi, P.; Cardinale, G.; Demichele, M.; Nanna, F.; Viggiano, D.; Bonini, C.; D'Alessio, L.; D'Auria, M.; Teghil, R.; Tofani, D.

1999-01-01

In the present paper, the effects of the steam explosion (ES) pretreatment conditions on recovery and chemical structure of wheat straw lignin are reported. The experimental data of lignin recovery by caustic extraction, followed by acid precipitation, have been interpolated to obtain the dependence on the time and temperature of SE. The lignin has been characterised by using several methods. Preliminary results on the synthesis of copolymers lignin-styrene are also reported [it

Using Remote Sensing to Evaluate Wetland Recovery in the Northern Tampa Bay Area Following Reduction in Groundwater Withdrawals

Science.gov (United States)

Elder, Amor

In the past, the Northern Tampa Bay Area (NTBA) wetlands saw severe declines in hydrologic conditions due to excessive groundwater withdrawal rates. Eventually these rates were reduced to allow the wetlands to recover. To monitor this recovery, the Southwest Florida Water Management district (SWFWMD) set up a fieldwork based scoring methodology, called the Wetlands Assessment Procedure (WAP). WAP has been used in many studies of the area since groundwater withdrawal reductions; with many of those studies finding the recovery to be mixed at best. However, these studies were very limited in the number of wetlands they could assess due to the limitations of fieldwork. Therefore, it was proposed that remotely sensed variables associated with water consumption and stress be used to assess the recovery of the NTBA wetlands, as remote sensing allows for efficient assessments of targets over large area. Utilizing ASTER imagery scenes from 2005 and 2014, 211 wetlands' remotely sensed responses of NDVI, Land Surface Temperature (LST), and Evapotranspiration (ET) were mapped and statistically examined for trends indicating improvement or decline. Furthermore, a subset of WAP scores for the two years were examined and compared to the remotely sensed values. The results were contradictory, with remotely sensed responses showing an improvement over the time period, WAP scores indicating a decline in hydrologic conditions, and the two methods showing little to no fit when modeled against each other. As such, it is believed at this time that the remotely sensed method is not suitable for measuring the indicators of wetland recovery used in the WAP methodology.

Effective use of complex secondary recovery methods in operation of small oil fields

Energy Technology Data Exchange (ETDEWEB)

Ibragimov, M R; Akulov, V P; Khutorov, A M

1966-11-01

The North Sokhs Field, located in the southern part of the Fergen depression, is composed of many horizons and has an anticlinal structure. The eighth horizon has highest oil saturation, with an average porosity of 17% and permeability of 80 md. Poor oil recovery was initially obtained from this horizon because the basic producing mechanism was solution gas drive. In 1961, when reservoir pressure was 94 kg/cmU2D and gas factor was 700-800mU3D/ton, pressure maintenance was initiated by injection of gas to the structure. Gas injection improved oil recovery considerably; however, high gas-oil ratios appeared in several wells. Next, peripheral water injection was started, and continued simultaneously with gas injection. The simultaneous injection of gas and water almost doubled oil production. Because of continued, high produced gas/oil ratios, gas injection was eventually discontinued, while water injection was continued. Water injection is building up reservoir pressure and improving oil recovery.

Hydrogen utilization potential in subsurface sediments

Directory of Open Access Journals (Sweden)

Rishi Ram Adhikari

2016-01-01

Full Text Available Subsurface microbial communities undertake many terminal electron-accepting processes, often simultaneously. Using a tritium-based assay, we measured the potential hydrogen oxidation catalyzed by hydrogenase enzymes in several subsurface sedimentary environments (Lake Van, Barents Sea, Equatorial Pacific and Gulf of Mexico with different predominant electron-acceptors. Hydrogenases constitute a diverse family of enzymes expressed by microorganisms that utilize molecular hydrogen as a metabolic substrate, product or intermediate. The assay reveals the potential for utilizing molecular hydrogen and allows qualitative detection of microbial activity irrespective of the predominant electron-accepting process. Because the method only requires samples frozen immediately after recovery, the assay can be used for identifying microbial activity in subsurface ecosystems without the need to preserve live material.We measured potential hydrogen oxidation rates in all samples from multiple depths at several sites that collectively span a wide range of environmental conditions and biogeochemical zones. Potential activity normalized to total cell abundance ranges over five orders of magnitude and varies, dependent upon the predominant terminal electron acceptor. Lowest per-cell potential rates characterize the zone of nitrate reduction and highest per-cell potential rates occur in the methanogenic zone. Possible reasons for this relationship to predominant electron acceptor include (i increasing importance of fermentation in successively deeper biogeochemical zones and (ii adaptation of H2ases to successively higher concentrations of H2 in successively deeper zones.

An Analytical Approach for Fast Recovery of the LSI Properties in Magnetic Particle Imaging

Directory of Open Access Journals (Sweden)

Hamed Jabbari Asl

2016-01-01

Full Text Available Linearity and shift invariance (LSI characteristics of magnetic particle imaging (MPI are important properties for quantitative medical diagnosis applications. The MPI image equations have been theoretically shown to exhibit LSI; however, in practice, the necessary filtering action removes the first harmonic information, which destroys the LSI characteristics. This lost information can be constant in the x-space reconstruction method. Available recovery algorithms, which are based on signal matching of multiple partial field of views (pFOVs, require much processing time and a priori information at the start of imaging. In this paper, a fast analytical recovery algorithm is proposed to restore the LSI properties of the x-space MPI images, representable as an image of discrete concentrations of magnetic material. The method utilizes the one-dimensional (1D x-space imaging kernel and properties of the image and lost image equations. The approach does not require overlapping of pFOVs, and its complexity depends only on a small-sized system of linear equations; therefore, it can reduce the processing time. Moreover, the algorithm only needs a priori information which can be obtained at one imaging process. Considering different particle distributions, several simulations are conducted, and results of 1D and 2D imaging demonstrate the effectiveness of the proposed approach.

Optimum length of finned pipe for waste heat recovery

International Nuclear Information System (INIS)

Soeylemez, M.S.

2008-01-01

A thermoeconomic feasibility analysis is presented yielding a simple algebraic optimization formula for estimating the optimum length of a finned pipe that is used for waste heat recovery. A simple economic optimization method is used in the present study by combining it with an integrated overall heat balance method based on fin effectiveness for calculating the maximum savings from a waste heat recovery system

Optimal recovery of linear operators in non-Euclidean metrics

Energy Technology Data Exchange (ETDEWEB)

Osipenko, K Yu [Moscow State Aviation Technological University, Moscow (Russian Federation)

2014-10-31

The paper looks at problems concerning the recovery of operators from noisy information in non-Euclidean metrics. A number of general theorems are proved and applied to recovery problems for functions and their derivatives from the noisy Fourier transform. In some cases, a family of optimal methods is found, from which the methods requiring the least amount of original information are singled out. Bibliography: 25 titles.

Sensitivity analysis of recovery efficiency in high-temperature aquifer thermal energy storage with single well

International Nuclear Information System (INIS)

Jeon, Jun-Seo; Lee, Seung-Rae; Pasquinelli, Lisa; Fabricius, Ida Lykke

2015-01-01

High-temperature aquifer thermal energy storage system usually shows higher performance than other borehole thermal energy storage systems. Although there is a limitation in the widespread use of the HT-ATES system because of several technical problems such as clogging, corrosion, etc., it is getting more attention as these issues are gradually alleviated. In this study, a sensitivity analysis of recovery efficiency in two cases of HT-ATES system with a single well is conducted to select key parameters. For a fractional factorial design used to choose input parameters with uniformity, the optimal Latin hypercube sampling with an enhanced stochastic evolutionary algorithm is considered. Then, the recovery efficiency is obtained using a computer model developed by COMSOL Multiphysics. With input and output variables, the surrogate modeling technique, namely the Gaussian-Kriging method with Smoothly Clopped Absolute Deviation Penalty, is utilized. Finally, the sensitivity analysis is performed based on the variation decomposition. According to the result of sensitivity analysis, the most important input variables are selected and confirmed to consider the interaction effects for each case and it is confirmed that key parameters vary with the experiment domain of hydraulic and thermal properties as well as the number of input variables. - Highlights: • Main and interaction effects on recovery efficiency in HT-ATES was investigated. • Reliability depended on fractional factorial design and interaction effects. • Hydraulic permeability of aquifer had an important impact on recovery efficiency. • Site-specific sensitivity analysis of HT-ATES was recommended.

Hurricane Sandy, Disaster Preparedness, and the Recovery Model.

Science.gov (United States)

Pizzi, Michael A

2015-01-01

Hurricane Sandy was the second largest and costliest hurricane in U.S. history to affect multiple states and communities. This article describes the lived experiences of 24 occupational therapy students who lived through Hurricane Sandy using the Recovery Model to frame the research. Occupational therapy student narratives were collected and analyzed using qualitative methods and framed by the Recovery Model. Directed content and thematic analysis was performed using the 10 components of the Recovery Model. The 10 components of the Recovery Model were experienced by or had an impact on the occupational therapy students as they coped and recovered in the aftermath of the natural disaster. This study provides insight into the lived experiences and recovery perspectives of occupational therapy students who experienced Hurricane Sandy. Further research is indicated in applying the Recovery Model to people who survive disasters. Copyright © 2015 by the American Occupational Therapy Association, Inc.

Multi-stage classification method oriented to aerial image based on low-rank recovery and multi-feature fusion sparse representation.

Science.gov (United States)

Ma, Xu; Cheng, Yongmei; Hao, Shuai

2016-12-10

Automatic classification of terrain surfaces from an aerial image is essential for an autonomous unmanned aerial vehicle (UAV) landing at an unprepared site by using vision. Diverse terrain surfaces may show similar spectral properties due to the illumination and noise that easily cause poor classification performance. To address this issue, a multi-stage classification algorithm based on low-rank recovery and multi-feature fusion sparse representation is proposed. First, color moments and Gabor texture feature are extracted from training data and stacked as column vectors of a dictionary. Then we perform low-rank matrix recovery for the dictionary by using augmented Lagrange multipliers and construct a multi-stage terrain classifier. Experimental results on an aerial map database that we prepared verify the classification accuracy and robustness of the proposed method.

The role of service recovery in HMO satisfaction.

Science.gov (United States)

Sarel, D; Marmorstein, H

1999-01-01

Complaint handling and service recovery by HMOs may be more efficient to implement and more determinant of customer satisfaction and retention than other approaches such as improving access to care. The current findings are consistent with research on recovery efforts in other industries. Complaint handling systems must achieve rapid and comprehensive identification and resolution of HMO member problems. Both cultural change and appropriate incentives to re-educate employees within HMO organizations are additional requisites to effective service recovery. The benefits to the HMO of expenditures on service recovery should be more immediate and sustainable than the benefits derived from other methods of increasing member satisfaction.

Quantitative determination of the crystalline phases of the ceramic materials utilizing the Rietveld method

International Nuclear Information System (INIS)

Kniess, C.T.; Prates, P.B.; Lima, J.C. de; Kuhnen, N.C.; Riella, H.G.; Maliska, A.M.

2009-01-01

Ceramic materials have properties defined by their chemical and micro-structural composition. The quantification of the crystalline phases is a fundamental stage in the determination of the structure, properties and applications of a ceramic material. Within this context, this study aims is the quantitative determination of the crystalline phases of the ceramic materials developed with addition of mineral coal bottom ash, utilizing the X ray diffraction technique, through the method proposed by Rietveld. For the formulation of the ceramic mixtures a {3,3} simplex-lattice design was used, giving ten formulations of three components (two different types of clays and coal bottom ash). The crystalline phases identified in the ceramic materials after sintering at 1150 deg C during two hours are: quartz, tridimite, mullite and hematite. The proposed methodology utilizing the Rietveld method for the quantification relating to crystalline phases of the materials was shown to be adequate and efficient. (author)

Recovery in SoccerPart II—Recovery Strategies

OpenAIRE

Nedelec, Mathieu; McCall, Alan; Carling, Chris; Legall, Franck; Berthoin, Serge; Dupont, Grégory

2013-01-01

International audience; In the formerly published part I of this two-part review, we examined fatigue after soccer matchplay and recovery kinetics of physical performance, and cognitive, subjective and biological markers. To reduce the magnitude of fatigue and to accelerate the time to fully recover after completion, several recovery strategies are now used in professional soccer teams. During congested fixture schedules, recovery strategies are highly required to alleviate post-match fatigue...

A self-reference PRF-shift MR thermometry method utilizing the phase gradient

International Nuclear Information System (INIS)

Langley, Jason; Potter, William; Phipps, Corey; Zhao Qun; Huang Feng

2011-01-01

In magnetic resonance (MR) imaging, the most widely used and accurate method for measuring temperature is based on the shift in proton resonance frequency (PRF). However, inter-scan motion and bulk magnetic field shifts can lead to inaccurate temperature measurements in the PRF-shift MR thermometry method. The self-reference PRF-shift MR thermometry method was introduced to overcome such problems by deriving a reference image from the heated or treated image, and approximates the reference phase map with low-order polynomial functions. In this note, a new approach is presented to calculate the baseline phase map in self-reference PRF-shift MR thermometry. The proposed method utilizes the phase gradient to remove the phase unwrapping step inherent to other self-reference PRF-shift MR thermometry methods. The performance of the proposed method was evaluated using numerical simulations with temperature distributions following a two-dimensional Gaussian function as well as phantom and in vivo experimental data sets. The results from both the numerical simulations and experimental data show that the proposed method is a promising technique for measuring temperature. (note)

Oil recovery enhancement from fractured, low permeability reservoirs. Part 2, Annual report, October 1, 1990--September 31, 1991

Energy Technology Data Exchange (ETDEWEB)

Poston, S.W.

1991-12-31

The results of the investigative efforts for this jointly funded DOE-State of Texas research project achieved during the 1990--1991 year may be summarized as follows: Geological Characterization -- Detailed maps of the development and hierarchical nature the fracture system exhibited by Austin Chalk outcrops were prepared. These results of these efforts were directly applied to the development of production decline type curves applicable to a dual fracture-matrix flow system. Analysis of production records obtained from Austin Chalk operators illustrated the utility of these type curves to determine relative fracture/matrix contributions and extent. Well-log response in Austin Chalk wells has been shown to be a reliable indicator of organic maturity. (VSP) Vertical-Seismic Profile data was used to use shear-wave splitting concepts to estimate fracture orientations. Several programs were to be written to facilitate analysis of the data. The results of these efforts indicated fractures could be detected with VSP seismic methods. Development of the (EOR) Enhanced Oil Recovery Imbibition Process -- Laboratory displacement as well as MRI and CT imaging studies have shown the carbonated water-imbibition displacement process significantly accelerates and increases recovery of an oil saturated, low permeability core material, when compared to that of a normal brine imbibition displacement process. A study of oil recovery by the application of a cyclic carbonated water imbibition process, followed by reducing the pressure below the bubble point of the CO{sub 2}-water solution, indicated the possibility of alternate and new enhanced recovery method. The installation of an artificial solution gas drive significantly increased oil recovery. The extent and arrangement of micro-fractures in Austin Chalk horizontal cores was mapped with CT scanning techniques. The degree of interconnection of the micro-fractures was easily visualized.

A new method for predicting functional recovery of stroke patients with hemiplegia: logarithmic modelling.

Science.gov (United States)

Koyama, Tetsuo; Matsumoto, Kenji; Okuno, Taiji; Domen, Kazuhisa

2005-10-01

To examine the validity and applicability of logarithmic modelling for predicting functional recovery of stroke patients with hemiplegia. Longitudinal postal survey. Stroke patients with hemiplegia staying in a long-term rehabilitation facility, who had been referred from acute medical service 30-60 days after onset. Functional Independence Measure (FIM) scores were periodically assessed during hospitalization. For each individual, a logarithmic formula that was scaled by an interval increase in FIM scores during the initial 2-6 weeks was used for predicting functional recovery. For the study, we recruited 18 patients who showed a wide variety of disability levels on admission (FIM scores 25-107). For each patient, the predicted FIM scores derived from the logarithmic formula matched the actual change in FIM scores. The changes predicted the recovery of motor rather than cognitive functions. Regression analysis showed a close fit between logarithmic modelling and actual FIM scores (across-subject R2 = 0.945). Provided with two initial time-point samplings, logarithmic modelling allows accurate prediction of functional recovery for individuals. Because the modelling is mathematically simple, it can be widely applied in daily clinical practice.

Short-term Recovery after Orthognathic Surgery: A Medical Daily Diary Approach

Science.gov (United States)

Blakey, George

2008-01-01

This study assessed the utility of a quality-of-life diary for the assessment of postoperative recovery following orthognathic surgery. A 20-item daily recovery diary was designed to assess the patients’ perception of recovery in 4 domains (postoperative sequelae; pain/discomfort; oral function; daily activities) during each of the first 90 days after surgery. Fifteen of 185 patients who had agreed to participate did not return any portion of the diary. Of the remaining patients, 87% returned the full 90 days requested. Younger patients were more likely to complete the entire protocol (P = 0.01). At 30 days, a lower percentage, in general, of patients who completed all 90 days reported recovery in oral function and general activity compared with those who did not complete all diary days. This study confirms that patients will cooperate with the completion of structured medical / health-related quality-of-life diaries during the first few months after orthognathic surgery. Information from such diaries would be valuable to patients deciding on treatment options and to the clinicians counseling them. PMID:18768296

Utilization of baker's yeast (Saccharomyces cerevisiae for the production of yeast extract: effects of different enzymatic treatments on solid, protein and carbohydrate recovery

Directory of Open Access Journals (Sweden)

TATJANA VUKASINOVIC MILIC

2007-05-01

Full Text Available Yeast extract (YE was produced from commercial pressed baker's yeast (active and inactivated using two enzymes: papain and lyticase. The effects of enzyme concentration and hydrolysis time on the recovery of solid, protein and carbohydrate were investigated. Autolysis, as a basic method for cell lysis was also used and the results compared. The optimal extraction conditions were investigated. The optimal concentrations of papain and lyticase were found to be 2.5 % and 0.025 %, respectively.

Platelet function testing: methods of assessment and clinical utility.

LENUS (Irish Health Repository)

Mylotte, Darren

2012-02-01

Platelets play a central role in the regulation of both thrombosis and haemostasis yet tests of platelet function have, until recently, been exclusively used in the diagnosis and management of bleeding disorders. Recent advances have demonstrated the clinical utility of platelet function testing in patients with cardiovascular disease. The ex vivo measurement of response to antiplatelet therapies (aspirin and clopidogrel), by an ever-increasing array of platelet function tests, is with some assays, predictive of adverse clinical events and thus, represents an emerging area of interest for both the clinician and basic scientist. This review article will describe the advantages and disadvantages of the currently available methods of measuring platelet function and discuss both the limitations and emerging data supporting the role of platelet function studies in clinical practice.

Platelet function testing: methods of assessment and clinical utility.

LENUS (Irish Health Repository)

Mylotte, Darren

2011-01-01

Platelets play a central role in the regulation of both thrombosis and haemostasis yet tests of platelet function have, until recently, been exclusively used in the diagnosis and management of bleeding disorders. Recent advances have demonstrated the clinical utility of platelet function testing in patients with cardiovascular disease. The ex vivo measurement of response to antiplatelet therapies (aspirin and clopidogrel), by an ever-increasing array of platelet function tests, is with some assays, predictive of adverse clinical events and thus, represents an emerging area of interest for both the clinician and basic scientist. This review article will describe the advantages and disadvantages of the currently available methods of measuring platelet function and discuss both the limitations and emerging data supporting the role of platelet function studies in clinical practice.

Recovery from cannabis use disorders: Abstinence versus moderation and treatment-assisted recovery versus natural recovery.

Science.gov (United States)

Stea, Jonathan N; Yakovenko, Igor; Hodgins, David C

2015-09-01

The present study of recovery from cannabis use disorders was undertaken with 2 primary objectives that address gaps in the literature. The first objective was to provide an exploratory portrait of the recovery process from cannabis use disorders, comparing individuals who recovered naturally with those who were involved in treatment. The second objective was to explore systematically the similarities and differences between abstinence and moderation recoveries. Adults who have recovered from a cannabis use disorder were recruited in the community (N = 119). The abstinence and treatment-assisted participants exhibited higher levels of lifetime cannabis problem severity than the moderation and natural recovery participants, respectively. As well, cognitive factors were identified as the most useful strategies for recovery (e.g., thinking about benefits and negative consequences of cannabis), followed by behavioral factors (e.g., avoidance of triggers for use and high-risk situations). Findings lend further support to the effectiveness of cognitive, motivational, and behavioral strategies as helpful actions and maintenance factors involved in the recovery process. The findings also generally support the idea that cannabis use disorders lie on a continuum of problem severity, with moderation and natural recoveries more likely to occur at the lower end of the continuum and abstinence and treatment-assisted recoveries more likely to occur at the upper end. (c) 2015 APA, all rights reserved).

Energy, exergy, environmental and economic analysis of industrial fired heaters based on heat recovery and preheating techniques

International Nuclear Information System (INIS)

Shekarchian, M.; Zarifi, F.; Moghavvemi, M.; Motasemi, F.; Mahlia, T.M.I.

2013-01-01

Highlights: • 4-E analysis of a typical industrial grade fired heater unit is studied. • This analysis is accomplished for the first time in this study. • Heat recovery and air preheating lead to substantial reduction in the fuel consumption. • The company’s current costs are tremendously reduced by these methods. • The methods lead to mitigation in GHG emission and to reduction in the associated taxes. - Abstract: Fired heaters are ubiquitous in both the petroleum and petrochemical industries, due to it being vital in their day to day operations. They form major components in petroleum refineries, petrochemical facilities, and processing units. This study was commissioned in order to analyze the economic benefits of incorporating both heat recovery and air preheating methods into the existing fired heater units. Four fired heater units were analyzed from the energy and environmental point of views. Moreover, the second law efficiency and the rate of irreversibility were also analyzed via the exergy analysis. Both analyses was indicative of the fact that the heat recovery process enhances both the first and second law efficiencies while simultaneously assisting in the production of high and low pressure water steam. The implementation and usage of the process improves the thermal and exergy efficiencies from 63.4% to 71.7% and 49.4%, to 54.8%, respectively. Additionally, the heat recovery and air preheating methods leads to a substantial reduction in fuel consumption, in the realm of up to 7.4%, while also simultaneously decreasing heat loss and the irreversibility of the unit. Nevertheless, the results of the economic analysis posits that although utilizing an air preheater unit enhances the thermal performance of the system, due to the air preheater’s capital and maintenance costs, incorporating an air preheater unit to an existing fired heater is not economically justifiable. Furthermore, the results of the sensitivity analysis and payback period

Comparative Analysis of Processes for Recovery of Rare Earths from Bauxite Residue

Science.gov (United States)

Borra, Chenna Rao; Blanpain, Bart; Pontikes, Yiannis; Binnemans, Koen; Van Gerven, Tom

2016-11-01

Environmental concerns and lack of space suggest that the management of bauxite residue needs to be re-adressed. The utilization of the residue has thus become a topic high on the agenda for both academia and industry, yet, up to date, it is only rarely used. Nonetheless, recovery of rare earth elements (REEs) with or without other metals from bauxite residue, and utilization of the left-over residue in other applications like building materials may be a viable alternative to storage. Hence, different processes developed by the authors for recovery of REEs and other metals from bauxite residue were compared. In this study, preliminary energy and cost analyses were carried out to assess the feasibility of the processes. These analyses show that the combination of alkali roasting-smelting-quenching-leaching is a promising process for the treatment of bauxite residue and that it is justified to study this process at a pilot scale.

Targeting the maximum heat recovery for systems with heat losses and heat gains

International Nuclear Information System (INIS)

Wan Alwi, Sharifah Rafidah; Lee, Carmen Kar Mun; Lee, Kim Yau; Abd Manan, Zainuddin; Fraser, Duncan M.

2014-01-01

Graphical abstract: Illustration of heat gains and losses from process streams. - Highlights: • Maximising energy savings through heat losses or gains. • Identifying location where insulation can be avoided. • Heuristics to maximise heat losses or gains. • Targeting heat losses or gains using the extended STEP technique and HEAT diagram. - Abstract: Process Integration using the Pinch Analysis technique has been widely used as a tool for the optimal design of heat exchanger networks (HENs). The Composite Curves and the Stream Temperature versus Enthalpy Plot (STEP) are among the graphical tools used to target the maximum heat recovery for a HEN. However, these tools assume that heat losses and heat gains are negligible. This work presents an approach that considers heat losses and heat gains during the establishment of the minimum utility targets. The STEP method, which is plotted based on the individual, as opposed to the composite streams, has been extended to consider the effect of heat losses and heat gains during stream matching. Several rules to guide the proper location of pipe insulation, and the appropriate procedure for stream shifting have been introduced in order to minimise the heat losses and maximise the heat gains. Application of the method on two case studies shows that considering heat losses and heat gains yield more realistic utility targets and help reduce both the insulation capital cost and utility cost of a HEN

Multi-layer solid-phase extraction and evaporation-enrichment methods for polar organic chemicals from aqueous matrices.

Science.gov (United States)

Köke, Niklas; Zahn, Daniel; Knepper, Thomas P; Frömel, Tobias

2018-03-01

Analysis of polar organic chemicals in the aquatic environment is exacerbated by the lack of suitable and widely applicable enrichment methods. In this work, we assessed the suitability of a novel combination of well-known solid-phase extraction (SPE) materials in one cartridge as well as an evaporation method and for the enrichment of 26 polar model substances (predominantly log D evaporation method were investigated for the recovery and matrix effects of the model substances and analyzed with hydrophilic interaction liquid chromatography-tandem mass spectrometry (HILIC-MS/MS). In total, 65% of the model substances were amenable (> 10% recovery) to the mlSPE method with a mean recovery of 76% while 73% of the model substances were enriched with the evaporation method achieving a mean recovery of 78%. Target and non-target screening comparison of both methods with a frequently used reversed-phase SPE method utilizing "hydrophilic and lipophilic balanced" (HLB) material was performed. Target analysis showed that the mlSPE and evaporation method have pronounced advantages over the HLB method since the HLB material retained only 30% of the model substances. Non-target screening of a ground water sample with the investigated enrichment methods showed that the median retention time of all detected features on a HILIC system decreased in the order mlSPE (3641 features, median t R 9.7 min), evaporation (1391, 9.3 min), HLB (4414, 7.2 min), indicating a higher potential of the described methods to enrich polar analytes from water compared with HLB-SPE. Graphical abstract Schematic of the method evaluation (recovery and matrix effects) and method comparison (target and non-target analysis) of the two investigated enrichment methods for very polar chemicals in aqueousmatrices.

Thermal enhanced oil recovery in Indonesia. Prospect of HTGR application

International Nuclear Information System (INIS)

Rahman, M.; Sumardiono; Lasman, A.N.; Sudarto; Prihardany, D.

1997-01-01

In the next future, Indonesia will face oil scarcity. The present reserves are estimated to be depleted in 20 years. However, after primary and secondary recovery processes, there are still more than 50% of original oil in place remaining in the reservoir, and this could be recovered by using tertiary recovery method or which is known as enhanced oil recovery (EOR) processes. Among the three major methods of EOR, steam flooding is a thermal recovery method into which High Temperature Reactor (HTR) module can be integrated for producing steam. However, the feasibility of application of HTR as an alternative to conventional oil-fired steam generator will depend strongly on the price of oil. This paper discusses EOR screening for Indonesian oil fields to identify the appropriate oil reservoirs for steam flooding application as well as the possibility of steam supply by HTR module. Also reviewed is the previous study on HTR application for Duri Steam Flood Project. (author). 8 refs, 6 figs, 5 tabs