Air Evaporation closed cycle water recovery technology - Advanced energy saving designs

Science.gov (United States)

Morasko, Gwyndolyn; Putnam, David F.; Bagdigian, Robert

1986-01-01

The Air Evaporation water recovery system is a visible candidate for Space Station application. A four-man Air Evaporation open cycle system has been successfully demonstrated for waste water recovery in manned chamber tests. The design improvements described in this paper greatly enhance the system operation and energy efficiency of the air evaporation process. A state-of-the-art wick feed design which results in reduced logistics requirements is presented. In addition, several design concepts that incorporate regenerative features to minimize the energy input to the system are discussed. These include a recuperative heat exchanger, a heat pump for energy transfer to the air heater, and solar collectors for evaporative heat. The addition of the energy recovery devices will result in an energy reduction of more than 80 percent over the systems used in earlier manned chamber tests.

Design of the Brine Evaporation Bag for Increased Water Recovery in Microgravity

Science.gov (United States)

Hayden, Anna L.; Delzeit, Lance D.

2015-01-01

The existing water recovery system on the International Space Station (ISS) is limited to 75% reclamation; consequently, long duration space missions are currently unfeasible due to the large quantity of water necessary to sustain the crew. The Brine Evaporation Bag (BEB) is a proposed system to supplement the existing water recovery system aboard the ISS that can to increase water recovery to 99%. The largest barrier to high water recovery is mineral scaling inside the water recovery equipment, which leads to equipment failure; therefore, some water must remain to keep the minerals dissolved. This waste stream is liquid brine containing salts, acids, organics, and water. The BEB is designed to recover this remaining water while protecting the equipment from scale. The BEB consists of a sealed bag containing a hydrophobic membrane that allows water vapor and gas to pass through. It is operated under vacuum, heated, and continuously filled with brine to boil away the water. The water vapor is recovered and the solids are contained inside the bag for disposal. The BEB can dry the brine to a solid block. Ongoing work includes improving the design of the BEB and the evaporator to prevent leaks, maximize the rate of water removal, and minimize energy use and weight. Additional testing will determine whether designs are heat- or mass-transfer limited and the optimal water recovery rate.

A dual model approach to ground water recovery trench design

International Nuclear Information System (INIS)

Clodfelter, C.L.; Crouch, M.S.

1992-01-01

The design of trenches for contaminated ground water recovery must consider several variables. This paper presents a dual-model approach for effectively recovering contaminated ground water migrating toward a trench by advection. The approach involves an analytical model to determine the vertical influence of the trench and a numerical flow model to determine the capture zone within the trench and the surrounding aquifer. The analytical model is utilized by varying trench dimensions and head values to design a trench which meets the remediation criteria. The numerical flow model is utilized to select the type of backfill and location of sumps within the trench. The dual-model approach can be used to design a recovery trench which effectively captures advective migration of contaminants in the vertical and horizontal planes

33 CFR 334.660 - Gulf of Mexico and Apalachicola Bay south of Apalachicola, Fla., Drone Recovery Area, Tyndall Air...

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Gulf of Mexico and Apalachicola Bay south of Apalachicola, Fla., Drone Recovery Area, Tyndall Air Force Base, Fla. 334.660 Section 334... Apalachicola, Fla., Drone Recovery Area, Tyndall Air Force Base, Fla. (a) The restricted area. A rectangular...

Natural recovery of different areas of a deserted quarry in South China

Institute of Scientific and Technical Information of China (English)

DUAN Wenjun; REN Hai; FU Shenglei; WANG Jun; YANG Long; ZHANG Jinping

2008-01-01

A quarry is a surface mining operated place, which produces enormous quantities of gravel, limestone, and other materials for industrial and construction applications. Restoration and revegetation of deserted quarries are becoming increasingly important. Three areas of a typical quarry in South China: terrace for crushed materials (terrace), spoiled mound, and remaining side slope, were investigated, to compare the existing plant species and to study the relationship between environmental factors and revegetation. The plant species composition of these three areas was found to differ significantly after eight years of natural recovery. The typical plant communities found over them were composed of gramineous herbs, fems, and shrubs. Soil organic matter, soil moisture, and soil bulk density were considered to be the major determining factors for vegetation succession. There existed abiotic and biotic thresholds during quarrying restoration. Suggestions had been presented that could have accelerated the process of natural recovery in quarries.

Design of water and heat recovery networks for the simultaneous minimisation of water and energy consumption

International Nuclear Information System (INIS)

Polley, Graham Thomas; Picon-Nunez, Martin; Lopez-Maciel, Jose de Jesus

2010-01-01

This paper describes procedures for the design of processes in which water and energy consumption form a large part of the operating cost. Good process design can be characterised by a number of properties, amongst the most important are: efficient use of raw materials, low capital cost and good operability. In terms of thermodynamic analysis these processes can be characterised as being either a 'pinch' problem or a 'threshold' problem. This paper concentrates on developing designs for problems of the threshold type. Most of the problems discussed by previous workers have been of this type. With these properties in mind this work looks at the design of integrated water and energy systems that exhibit the following features: 1. minimum water consumption, 2. minimum energy consumption, and 3. simple network structure. The approach applies for single contaminant. It is shown that the water conservation problem and the heat recovery problems can be de-coupled and the water conservation options should be established first. It is then shown that the number of heaters and heat recovery units required for the system, the quantity and type of hot utility needed for the plant and the complexity of the heat recovery network can all be determined without having to design any heat recovery network. This allows the engineer to select the better water conservation option before embarking on the design of the heat recovery network. For this type of problem the design of the heat recovery network itself is usually simple and straightforward.

A multi-stage oil-water-separating process design for the sea oil spill recovery robot

Science.gov (United States)

Zhang, Min-ge; Wu, Jian-guo; Lin, Xinhua; Wang, Xiao-ming

2018-03-01

Oil spill have the most common pollution to the marine ecological environment. In the late stage of physical method recovery, because of the thin oil and the strong sea breeze, the recovery vessels has low efficiency and high energy consumption. This paper develops a multi-stage oil-water-separating process carried by the sea oil spill recovery robot in severe conditions. This design consists of three separation process, among which both the first and third process adopt corrugated sheets horizontal oil-water separator, while the second is hydraulic rotary breaker. This design also equiptment with rectifier and cyclone separator and other important components. This process has high flexibility and high recovery efficiency. The implement effect is significant.

Kinetic energy recovery systems in motor vehicles

Science.gov (United States)

Śliwiński, C.

2016-09-01

The article draws attention to the increasing environmental pollution caused by the development of vehicle transport and motorization. Different types of design solutions used in vehicles for the reduction of fuel consumption, and thereby emission of toxic gasses into the atmosphere, were specified. Historical design solutions concerning energy recovery devices in mechanical vehicles which used flywheels to accumulate kinetic energy were shown. Developmental tendencies in the area of vehicle manufacturing in the form of hybrid electric and electric devices were discussed. Furthermore, designs of energy recovery devices with electrical energy storage from the vehicle braking and shock absorbing systems were presented. A mechanical energy storing device using a flywheel operating under vacuum was presented, as were advantages and disadvantages of both systems, the limitations they impose on individual constructions and safety issues. The paper also discusses a design concept of an energy recovery device in mechanical vehicles which uses torsion springs as the main components of energy accumulation during braking. The desirability of a cooperation of both the mechanical- and electrical energy recovery devices was indicated.

Design and evaluation of fluidized bed heat recovery for diesel engine systems

Science.gov (United States)

Hamm, J. R.; Newby, R. A.; Vidt, E. J.; Lippert, T. E.

1985-01-01

The potential of utilizing fluidized bed heat exchangers in place of conventional counter-flow heat exchangers for heat recovery from adiabatic diesel engine exhaust gas streams was studied. Fluidized bed heat recovery systems were evaluated in three different heavy duty transport applications: (1) heavy duty diesel truck; (2) diesel locomotives; and (3) diesel marine pushboat. The three applications are characterized by differences in overall power output and annual utilization. For each application, the exhaust gas source is a turbocharged-adiabatic diesel core. Representative subposed exhaust gas heat utilization power cycles were selected for conceptual design efforts including design layouts and performance estimates for the fluidized bed heat recovery heat exchangers. The selected power cycles were: organic rankine with RC-1 working fluid, turbocompound power turbine with steam injection, and stirling engine. Fuel economy improvement predictions are used in conjunction with capital cost estimates and fuel price data to determine payback times for the various cases.

Recovery Trends of Commercial Fish: The Case of an Underperforming Mediterranean Marine Protected Area.

Science.gov (United States)

Marra, Stefano; Coppa, Stefania; Camedda, Andrea; Mazzoldi, Carlotta; Wrachien, Francesco; Massaro, Giorgio; de Lucia, G Andrea

2016-01-01

Temporal trends in the recovery of exploited species in marine protected areas (MPAs) are useful for a proper assessment of the efficacy of protection measures. The effects of protection on the fish assemblages of the sublittoral rocky reefs in the "Penisola del Sinis-Isola di Mal di Ventre" MPA (W. Sardinia, Italy) were evaluated using a multi-year series of data. Four surveys, conducted 7, 10, 13 and 15 years after the area was designated as an MPA and carried out in the period spanning June and July, were used to estimate the abundance and biomass of commercial species. The surveys were carried out in zones with decreasing levels of fishing restrictions within the MPA (zones A, B, C) and in unprotected zones (OUT1 and OUT2), and underwater video visual census techniques were used. Protected zones only occasionally showed higher levels of abundance or biomass, and the trajectories of those metrics were not consistent across the years. In addition, the zone with the highest level of protection (zone A) never presented levels of abundance and biomass higher than those in zones B and C. This study shows that even 15 years after designation, protection has had no appreciable effect in the MPA studied. It is argued that this is emblematic of several shortcomings in the planning, regulation and enforcement frameworks of the MPA.

Plastics disassembly versus bulk recycling: engineering design for end-of-life electronics resource recovery.

Science.gov (United States)

Rios, Pedro; Stuart, Julie Ann; Grant, Ed

2003-12-01

Annual plastic flows through the business and consumer electronics manufacturing supply chain include nearly 3 billion lb of high-value engineering plastics derived from petroleum. The recovery of resource value from this stream presents critical challenges in areas of materials identification and recycling process design that demand new green engineering technologies applied together with life cycle assessment and ecological supply chain analysis to create viable plastics-to-plastics supply cycles. The sustainable recovery of potentially high-value engineering plastics streams requires that recyclers either avoid mixing plastic parts or purify later by separating smaller plastic pieces created in volume reduction (shredding) steps. Identification and separation constitute significant barriers in the plastics-to-plastics recycling value proposition. In the present work, we develop a model that accepts randomly arriving electronic products to study scenarios by which a recycler might identify and separate high-value engineering plastics as well as metals. Using discrete eventsimulation,we compare current mixed plastics recovery with spectrochemical plastic resin identification and subsequent sorting. Our results show that limited disassembly with whole-part identification can produce substantial yields in separated streams of recovered engineering thermoplastics. We find that disassembly with identification does not constitute a bottleneck, but rather, with relatively few workers, can be configured to pull the process and thus decrease maximum staging space requirements.

Advanced regenerative heat recovery system

Science.gov (United States)

Prasad, A.; Jasti, J. K.

1982-02-01

A regenerative heat recovery system was designed and fabricated to deliver 1500 scfm preheated air to a maximum temperature of 1600 F. Since this system is operating at 2000 F, the internal parts were designed to be fabricated with ceramic materials. This system is also designed to be adaptable to an internal metallic structure to operate in the range of 1100 to 1500 F. A test facility was designed and fabricated to test this system. The test facility is equipped to impose a pressure differential of up to 27 inches of water column in between preheated air and flue gas lines for checking possible leakage through the seals. The preliminary tests conducted on the advanced regenerative heat recovery system indicate the thermal effectiveness in the range of 60% to 70%. Bench scale studies were conducted on various ceramic and gasket materials to identify the proper material to be used in high temperature applications. A market survey was conducted to identify the application areas for this heat recovery system. A cost/benefit analysis showed a payback period of less than one and a half years.

Vermont Designated Natural Areas

Data.gov (United States)

Vermont Center for Geographic Information — Under Natural Areas Law (10 Vermont Statutes Annotated, Chapter 83 � 2607) the FPR commissioner, with the approval of the governor, may designate and set aside areas...

Integrated working fluid-thermodynamic cycle design of organic Rankine cycle power systems for waste heat recovery

DEFF Research Database (Denmark)

Cignitti, Stefano; Andreasen, Jesper Graa; Haglind, Fredrik

2017-01-01

recovery. Inthis paper, an organic Rankine cycle process and its pure working fluid are designed simultaneously forwaste heat recovery of the exhaust gas from a marine diesel engine. This approach can overcome designissues caused by the high sensitivity between the fluid and cycle design variables......Today, some established working fluids are being phased out due to new international regulations on theuse of environmentally harmful substances. With an ever-increasing cost to resources, industry wants toconverge on improved sustainability through resource recovery, and in particular waste heat...

Experimental study of enhancing heating performance of the air-source heat pump by using a novel heat recovery device designed for reusing the energy of the compressor shell

International Nuclear Information System (INIS)

Huang, Bi; Jian, Qifei; Luo, Lizhong; Zhao, Jing

2017-01-01

Highlights: • A novel heat recovery device was designed and tested. • Aiming at avoiding liquid slugging in cold areas. • Recovery of the waste energy of compressor housing. • Refrigerant is heated with the energy recovered before it is sucked into the compressor. • Requires no extra power while the recovery system is operating. - Abstract: A novel heat recovery device designed to recover the heat that is released from the outer surface of heat pump compressors, and to enhance the performance of heat pumps in cold areas was made and tested in this study. The novel heat recovery device consists of three fundamental units: a heat absorption unit, a heat emission unit and heat pipes. An amount of work focused on recovering the heat of compressors through oil system, but few studies concentrated on the housing. The main advantage of the heat recovery device is no need for extra energy consumption for its only driving force is the temperature difference between the compressor shell and the working fluid inside the suction line. The experimental results were obtained from a series of tests with a R410A air-source heat pump. Effects of the device are analyzed with respect of the suction temperature, temperature distribution among the housing, input power and exergy destruction. Moreover, the impact on the heating capacity is also discussed. Further, direction for improvement is also given based on the analysis.

Language recovery after epilepsy surgery of the Broca's area

Directory of Open Access Journals (Sweden)

Lilit Mnatsakanyan

Full Text Available Epilepsy surgery is indicated in select patients with drug-resistant focal epilepsy. Seizure freedom or significant reduction of seizure burden without risking new neurological deficits is the expected goal of epilepsy surgery. Typically, when the seizure onset zone overlaps with eloquent cortex, patients are excluded from surgery.We present a patient with drug-resistant frontal lobe epilepsy who underwent successful surgery with resection of Broca's area, primarily involving the pars triangularis (BA 45. We report transient expressive aphasia followed by recovery of speech. This case provides new insights into adult neuroplasticity of the language network. Keywords: Epilepsy surgery, Eloquent cortex, Language and epilepsy, Refractory epilepsy, Electrocorticography

On the optimal design of the disassembly and recovery processes.

Science.gov (United States)

Xanthopoulos, A; Iakovou, E

2009-05-01

This paper tackles the problem of the optimal design of the recovery processes of the end-of-life (EOL) electric and electronic products, with a special focus on the disassembly issues. The objective is to recover as much ecological and economic value as possible, and to reduce the overall produced quantities of waste. In this context, a medium-range tactical problem is defined and a novel two-phased algorithm is presented for a remanufacturing-driven reverse supply chain. In the first phase, we propose a multicriteria/goal-programming analysis for the identification and the optimal selection of the most 'desirable' subassemblies and components to be disassembled for recovery, from a set of different types of EOL products. In the second phase, a multi-product, multi-period mixed-integer linear programming (MILP) model is presented, which addresses the optimization of the recovery processes, while taking into account explicitly the lead times of the disassembly and recovery processes. Moreover, a simulation-based solution approach is proposed for capturing the uncertainties in reverse logistics. The overall approach leads to an easy-to-use methodology that could support effectively middle level management decisions. Finally, the applicability of the developed methodology is illustrated by its application on a specific case study.

On the optimal design of the disassembly and recovery processes

International Nuclear Information System (INIS)

Xanthopoulos, A.; Iakovou, E.

2009-01-01

This paper tackles the problem of the optimal design of the recovery processes of the end-of-life (EOL) electric and electronic products, with a special focus on the disassembly issues. The objective is to recover as much ecological and economic value as possible, and to reduce the overall produced quantities of waste. In this context, a medium-range tactical problem is defined and a novel two-phased algorithm is presented for a remanufacturing-driven reverse supply chain. In the first phase, we propose a multicriteria/goal-programming analysis for the identification and the optimal selection of the most 'desirable' subassemblies and components to be disassembled for recovery, from a set of different types of EOL products. In the second phase, a multi-product, multi-period mixed-integer linear programming (MILP) model is presented, which addresses the optimization of the recovery processes, while taking into account explicitly the lead times of the disassembly and recovery processes. Moreover, a simulation-based solution approach is proposed for capturing the uncertainties in reverse logistics. The overall approach leads to an easy-to-use methodology that could support effectively middle level management decisions. Finally, the applicability of the developed methodology is illustrated by its application on a specific case study

PERLE. Powerful energy recovery linac for experiments. Conceptual design report

Science.gov (United States)

Angal-Kalinin, D.; Arduini, G.; Auchmann, B.; Bernauer, J.; Bogacz, A.; Bordry, F.; Bousson, S.; Bracco, C.; Brüning, O.; Calaga, R.; Cassou, K.; Chetvertkova, V.; Cormier, E.; Daly, E.; Douglas, D.; Dupraz, K.; Goddard, B.; Henry, J.; Hutton, A.; Jensen, E.; Kaabi, W.; Klein, M.; Kostka, P.; Lasheras, N.; Levichev, E.; Marhauser, F.; Martens, A.; Milanese, A.; Militsyn, B.; Peinaud, Y.; Pellegrini, D.; Pietralla, N.; Pupkov, Y.; Rimmer, R.; Schirm, K.; Schulte, D.; Smith, S.; Stocchi, A.; Valloni, A.; Welsch, C.; Willering, G.; Wollmann, D.; Zimmermann, F.; Zomer, F.

2018-06-01

A conceptual design is presented of a novel energy-recovering linac (ERL) facility for the development and application of the energy recovery technique to linear electron accelerators in the multi-turn, large current and large energy regime. The main characteristics of the powerful energy recovery linac experiment facility (PERLE) are derived from the design of the Large Hadron electron Collider, an electron beam upgrade under study for the LHC, for which it would be the key demonstrator. PERLE is thus projected as a facility to investigate efficient, high current (HC) (>10 mA) ERL operation with three re-circulation passages through newly designed SCRF cavities, at 801.58 MHz frequency, and following deceleration over another three re-circulations. In its fully equipped configuration, PERLE provides an electron beam of approximately 1 GeV energy. A physics programme possibly associated with PERLE is sketched, consisting of high precision elastic electron–proton scattering experiments, as well as photo-nuclear reactions of unprecedented intensities with up to 30 MeV photon beam energy as may be obtained using Fabry–Perot cavities. The facility has further applications as a general technology test bed that can investigate and validate novel superconducting magnets (beam induced quench tests) and superconducting RF structures (structure tests with HC beams, beam loading and transients). Besides a chapter on operation aspects, the report contains detailed considerations on the choices for the SCRF structure, optics and lattice design, solutions for arc magnets, source and injector and on further essential components. A suitable configuration derived from the here presented design concept may next be moved forward to a technical design and possibly be built by an international collaboration which is being established.

Safety analysis, 200 Area, Savannah River Plant: Separations area operations. Building 221-H, B-Line, Scrap Recovery Facility (Supplement 2A): Revision 1

Energy Technology Data Exchange (ETDEWEB)

None

1991-07-01

The now HB-Line is located an top of the 221-H Building on the fifth and sixth levels and is designed to replace the aging existing HB-Line production facility. The new HB-Line consists of three separate facilities: the Scrap Recovery Facility, Neptunium Facility, and Plutonium Oxide Facility. The Scrap Recovery Facility is designed to routinely generate nitrate solutions of {sup 235}U{sup 239}Pu and Pu-238 fromscrap for purification by anion exchange or by solvent extraction in the canyon. The now facility incorporates improvements in: (1) engineered controls for nuclear criticality, (2) cabinet integrity and engineered barriers to contain contamination and minimize personnel exposure to airborne contamination, (3) shielding and remote operations to decrease radiation exposure, and (4) equipment and ventilation design to provide flexibility and improved process performance.

Assessment of modularity architecture for recovery process of electric vehicle in supporting sustainable design

Science.gov (United States)

Baroroh, D. K.; Alfiah, D.

2018-05-01

The electric vehicle is one of the innovations to reduce the pollution of the vehicle. Nevertheless, it still has a problem, especially for disposal stage. In supporting product design and development strategy, which is the idea of sustainable design or problem solving of disposal stage, assessment of modularity architecture from electric vehicle in recovery process needs to be done. This research used Design Structure Matrix (DSM) approach to deciding interaction of components and assessment of modularity architecture using the calculation of value from 3 variables, namely Module Independence (MI), Module Similarity (MS), and Modularity for End of Life Stage (MEOL). The result of this research shows that existing design of electric vehicles has the architectural design which has a high value of modularity for recovery process on disposal stage. Accordingly, so it can be reused and recycled in component level or module without disassembly process to support the product that is environmentally friendly (sustainable design) and able reduce disassembly cost.

Early Phase Contingency Trajectory Design for the Failure of the First Lunar Orbit Insertion Maneuver: Direct Recovery Options

Science.gov (United States)

Song, Young-Joo; Bae, Jonghee; Kim, Young-Rok; Kim, Bang-Yeop

2017-12-01

To ensure the successful launch of the Korea pathfinder lunar orbiter (KPLO) mission, the Korea Aerospace Research Institute (KARI) is now performing extensive trajectory design and analysis studies. From the trajectory design perspective, it is crucial to prepare contingency trajectory options for the failure of the first lunar brake or the failure of the first lunar orbit insertion (LOI) maneuver. As part of the early phase trajectory design and analysis activities, the required time of flight (TOF) and associated delta-V magnitudes for each recovery maneuver (RM) to recover the KPLO mission trajectory are analyzed. There are two typical trajectory recovery options, direct recovery and low energy recovery. The current work is focused on the direct recovery option. Results indicate that a quicker execution of the first RM after the failure of the first LOI plays a significant role in saving the magnitudes of the RMs. Under the conditions of the extremely tight delta-V budget that is currently allocated for the KPLO mission, it is found that the recovery of the KPLO without altering the originally planned mission orbit (a 100 km circular orbit) cannot be achieved via direct recovery options. However, feasible recovery options are suggested within the boundaries of the currently planned delta-V budget. By changing the shape and orientation of the recovered final mission orbit, it is expected that the KPLO mission may partially pursue its scientific mission after successful recovery, though it will be limited.

A practical multi-objective design approach for optimum exhaust heat recovery from hybrid stand-alone PV-diesel power systems

International Nuclear Information System (INIS)

Yousefi, Moslem; Kim, Joong Hoon; Hooshyar, Danial; Yousefi, Milad; Sahari, Khairul Salleh Mohamed; Ahmad, Rodina Binti

2017-01-01

Highlights: • Heat recovery exchanger is designed based on practical conditions of a hybrid power system. • Off-the-grid electricity system modeling and analysis using micro-grid analysis software HOMER. • NSGA-II is used for the multi-objective design optimization task. • A new local search is proposed to incorporate the engineering knowledge in NSGA-II. • The proposed approach outperforms the existing ones. - Abstract: Integration of solar power and diesel generators (DGs) together with battery storage has proven to be an efficient choice for stand-alone power systems (SAPS). For higher energy efficiency, heat recovery from exhaust gas of the DG can also be employed to supply all or a portion of the thermal energy demand. Although the design of such heat recovery systems (HRSs) has been studied, the effect of solar power integration has not been taken into account. In this paper, a new approach for practical design of these systems based on varying engine loads is presented. Fast and elitist non-dominated sorting genetic algorithm (NSGA-II) equipped with a novel local search was used for the design process, considering conflicting objectives of annual energy recovery and total cost of the system, and six design variables. An integrated power system, designed for a remote SAPS, was used to evaluate the design approach. The optimum power supply system was first designed using the commercial software Hybrid Optimization of Multiple Energy Resources (HOMER), based on power demand and global solar energy in the region. Heat recovery design was based on the outcome of HOMER for DG hourly load, considering different power scenarios. The proposed approach improves the annual heat recovery of the PV/DG/battery system by 4%, PV/battery by 1.7%, and stand-alone DG by 1.8% when compared with a conventional design based on nominal DG load. The results prove that the proposed approach is effective and that load calculations should be taken into account prior to

Design of Hybrid Steam-In Situ Combustion Bitumen Recovery Processes

International Nuclear Information System (INIS)

Yang Xiaomeng; Gates, Ian D.

2009-01-01

Given enormous capital costs, operating expenses, flue gas emissions, water treatment and handling costs of thermal in situ bitumen recovery processes, improving the overall efficiency by lowering energy requirements, environmental impact, and costs of these production techniques is a priority. Steam-assisted gravity drainage (SAGD) is the most widely used in situ recovery technique in Athabasca reservoirs. Steam generation is done on surface and consequently, because of heat losses, the energy efficiency of SAGD can never be ideal with respect to the energy delivered to the sandface. An alternative to surface steam generation is in situ combustion (ISC) where heat is generated within the formation through injection of oxygen at a sufficiently high pressure to initiate combustion of bitumen. In this manner, the heat from the combustion reactions can be used directly to mobilize the bitumen. As an alternative, the heat can be used to generate steam within the formation which then is the agent to move heat in the reservoir. In this research, alternative hybrid techniques with simultaneous and sequential steam-oxygen injection processes are examined to maximize the thermal efficiency of the recovery process. These hybrid processes have the advantage that during ISC, steam is generated within the reservoir from injected and formation water and as a product of oxidation. This implies that ex situ steam generation requirements are reduced and if there is in situ storage of combustion gases, that overall gas emissions are reduced. In this research, detailed reservoir simulations are done to examine the dynamics of hybrid processes to enable design of these processes. The results reveal that hybrid processes can lower emitted carbon dioxide-to-oil ratio by about 46%, decrease the consumed natural gas-to-oil ratio by about 73%, reduce the cumulative energy-to-oil ratio by between 40% and 70% compared to conventional SAGD, and drop water consumption per unit oil produced

Cluster as a Service for Disaster Recovery in Intercloud Systems: Design and Modeling

OpenAIRE

Mohammad Ali Khoshkholghi

2014-01-01

Nowadays, all modern IT technologies aim to create dynamic and flexible environments. For this reason, InterCloud has been designed to provide a vast and flexible virtualized environment in which many clouds can interact with one another in a dynamic way. Disaster recovery is one of the main applications of InterCloud which can be supported by Cluster as a Service. However, the previous studies addressed disaster recovery and Cluster as a Service separately. In addition, system backup and dis...

Design and optimization of a large flow rate booster pump in SWRO energy recovery system

International Nuclear Information System (INIS)

Lai, Z N; Wu, P; Wu, D Z; Wang, L Q

2013-01-01

Seawater reverse osmosis (SWRO) is a high energy-consumption industry, so energy efficiency is an important issue. Energy recovery systems, which contain a pressure exchanger and a booster pump, are widely used in SWRO plants. As a key part of energy recovery system, the difficulty of designing booster pumps lies in high inlet pressure, high medium causticity and large flow rate. High inlet pressure adds difficulties to seal design, and large flow rate and high efficiency requirement bring high demand for hydraulic design. In this paper, a 625 m 3 /h booster pump is designed and optimized according to the CFD (Computational Fluid Dynamics) simulation results. The impeller and volute is well designed, a new type of high pressure mechanical seal is applied and axial force is well balanced. After optimization based on blade redesign, the efficiency of the pump was improved. The best efficiency reaches more than 85% at design point according to the CFD simulation result

Design and optimization of a large flow rate booster pump in SWRO energy recovery system

Science.gov (United States)

Lai, Z. N.; Wu, P.; Wu, D. Z.; Wang, L. Q.

2013-12-01

Seawater reverse osmosis (SWRO) is a high energy-consumption industry, so energy efficiency is an important issue. Energy recovery systems, which contain a pressure exchanger and a booster pump, are widely used in SWRO plants. As a key part of energy recovery system, the difficulty of designing booster pumps lies in high inlet pressure, high medium causticity and large flow rate. High inlet pressure adds difficulties to seal design, and large flow rate and high efficiency requirement bring high demand for hydraulic design. In this paper, a 625 m3/h booster pump is designed and optimized according to the CFD (Computational Fluid Dynamics) simulation results. The impeller and volute is well designed, a new type of high pressure mechanical seal is applied and axial force is well balanced. After optimization based on blade redesign, the efficiency of the pump was improved. The best efficiency reaches more than 85% at design point according to the CFD simulation result.

Lithium niobate ultrasonic transducer design for Enhanced Oil Recovery.

Science.gov (United States)

Wang, Zhenjun; Xu, Yuanming; Gu, Yuting

2015-11-01

Due to the strong piezoelectric effect possessed by lithium niobate, a new idea that uses lithium niobate to design high-power ultrasonic transducer for Enhanced Oil Recovery technology is proposed. The purpose of this paper is to lay the foundation for the further research and development of high-power ultrasonic oil production technique. The main contents of this paper are as follows: firstly, structure design technique and application of a new high-power ultrasonic transducer are introduced; secondly, the experiment for reducing the viscosity of super heavy oil by this transducer is done, the optimum ultrasonic parameters for reducing the viscosity of super heavy oil are given. Experimental results show that heavy large molecules in super heavy oil can be cracked into light hydrocarbon substances under strong cavitation effect caused by high-intensity ultrasonic wave. Experiment proves that it is indeed feasible to design high-power ultrasonic transducer for ultrasonic oil production technology using lithium niobate. Copyright © 2015 Elsevier B.V. All rights reserved.

Structural and mechanical design challenges of space shuttle solid rocket boosters separation and recovery subsystems

Science.gov (United States)

Woodis, W. R.; Runkle, R. E.

1985-01-01

The design of the space shuttle solid rocket booster (SRB) subsystems for reuse posed some unique and challenging design considerations. The separation of the SRBs from the cluster (orbiter and external tank) at 150,000 ft when the orbiter engines are running at full thrust meant the two SRBs had to have positive separation forces pushing them away. At the same instant, the large attachments that had reacted launch loads of 7.5 million pounds thrust had to be servered. These design considerations dictated the design requirements for the pyrotechnics and separation rocket motors. The recovery and reuse of the two SRBs meant they had to be safely lowered to the ocean, remain afloat, and be owed back to shore. In general, both the pyrotechnic and recovery subsystems have met or exceeded design requirements. In twelve vehicles, there has only been one instance where the pyrotechnic system has failed to function properly.

Conceptual process design for uranium recovery from sea water

International Nuclear Information System (INIS)

Suzuki, Motoyuki; Chihara, Kazuyuki; Fujimoto, Masahiko; Yagi, Hiroshi; Wada, Akihiko.

1985-01-01

Based on design of uranium recovery process from sea water, total cost for uranium production was estimated. Production scale of 1,000 ton-uranium per year was supposed, because of the big demand for uranium in the second age, i.e., fast breeder reactor age. The process is described as follows: Fluidized bed of hydrous titanium oxide (diameter is 0.1 mm, saturated adsorption capacity is 510 μg-U/g-Ad, adsorption capacity for ten days is 150 μg-U/g-Ad) is supposed, as an example, to be utilized as the primarily concentration unit. Fine adsorbent particles can be transferred as slurry in all of the steps of adsorption, washing, desorption, washing, regeneration. As an example, ammonium carbonate is applied to desorb the adsorbed uranium from titanium oxide. Then, stripping method is adopted for desorbent recovery. As for the secondary concentration, strong basic anion exchange method is supposed. The first step of process design is to determine the mass balance of each component through the whole process system by using the signal diagram. Then, the scale of each unit process, with which the mass balances are satisfied, is estimated by detailed chemical engineering calculation. Also, driving cost of each unit operation is estimated. As a result, minimum total cost of 160,000 yen/kg-U is obtained. Adsorption process cost is 80 to 90 % of the total cost. Capital cost and driving cost are fifty-fifty in the adsorption process cost. Pump driving cost forms a big part of the driving cost. Further concentrated study should be necessary on the adsorption process design. It might be important to make an effort on direct utilization of ocean current for saving the pump driving cost. (author)

Design and simulation of advanced charge recovery piezoactuator drivers

International Nuclear Information System (INIS)

Biancuzzi, G; Lemke, T; Woias, P; Goldschmidtboeing, F; Ruthmann, O; Schrag, H J; Vodermayer, B; Schmid, T

2010-01-01

The German Artificial Sphincter System project aims at the development of an implantable sphincter prosthesis driven by a piezoelectrically actuated micropump. The system has been designed to be fully implantable, i.e. the power supply is provided by a rechargeable lithium polymer battery. In order to provide sufficient battery duration and to limit battery dimensions, special effort has to be made to minimize power consumption of the whole system and, in particular, of the piezoactuator driver circuitry. Inductive charge recovery can be used to recover part of the charge stored within the actuator. We are going to present a simplified inductor-based circuit capable of voltage inversion across the actuator without the need of an additional negative voltage source. The dimension of the inductors required for such a concept is nevertheless significant. We therefore present a novel alternative concept, called direct switching, where the equivalent capacitance of the actuator is charged directly by a step-up converter and discharged by a step-down converter. We achieved superior performance compared to a simple inductor-based driver with the advantage of using small-size chip inductors. As a term of comparison, the performance of the aforementioned drivers is compared to a conventional driver that does not implement any charge recovery technique. With our design we have been able to achieve more than 50% reduction in power consumption compared to the simplest conventional driver. The new direct switching driver performs 15% better than an inductor-based driver. A novel, whole-system SPICE simulation is presented, where both the driving circuit and the piezoactuator are modeled making use of advanced nonlinear models. Such a simulation is a precious tool to design and optimize piezoactuator drivers

Final Report, Materials for Industrial Heat Recovery Systems, Tasks 3 and 4 Materials for Heat Recovery in Recovery Boilers

Energy Technology Data Exchange (ETDEWEB)

Keiser, James R.; Kish, Joseph R.; Singh, Preet M.; Sarma, Gorti B.; Yuan, Jerry; Gorog, J. Peter; Frederick, Laurie A.; Jette, Francois R.; Meisner, Roberta A.; Singbeil, Douglas L.

2007-12-31

The DOE-funded project on materials for industrial heat recovery systems included four research tasks: materials for aluminum melting furnace recuperator tubes, materials and operational changes to prevent cracking and corrosion of the co-extruded tubes that form primary air ports in black liquor recovery boilers, the cause of and means to prevent corrosion of carbon steel tubes in the mid-furnace area of recovery boilers, and materials and operational changes to prevent corrosion and cracking of recovery boiler superheater tubes. Results from studies on the latter two topics are given in this report while separate reports on results for the first two tasks have already been published. Accelerated, localized corrosion has been observed in the mid-furnace area of kraft recovery boilers. This corrosion of the carbon steel waterwall tubes is typically observed in the vicinity of the upper level of air ports where the stainless clad co-extruded wall tubes used in the lower portion of the boiler are welded to the carbon steel tubes that extend from this transition point or “cut line” to the top of the boiler. Corrosion patterns generally vary from one boiler to another depending on boiler design and operating parameters, but the corrosion is almost always found within a few meters of the cut line and often much closer than that. This localized corrosion results in tube wall thinning that can reach the level where the integrity of the tube is at risk. Collection and analysis of gas samples from various areas near the waterwall surface showed reducing and sulfidizing gases were present in the areas where corrosion was accelerated. However, collection of samples from the same areas at intervals over a two year period showed the gaseous environment in the mid-furnace section can cycle between oxidizing and reducing conditions. These fluctuations are thought to be due to gas flow instabilities and they result in an unstable or a less protective scale on the carbon steel

Prediction of the recovery rate after surgery for cervical myelopathy from the view of CT-myelography

International Nuclear Information System (INIS)

Koyanagi, Takahiro; Satomi, Kazuhiko; Asazuma, Takahito; Toyama, Yoshiaki; Fujimura, Shoichi; Hirabayashi, Kiyoshi; Hamano, Yasuyuki; Shiraishi, Takeshi.

1991-01-01

This study was designed to prepare a formula for predicting postoperative recovery in cervical myelopathy. Preoperative CT-myelography (CT-M) was performed in a total of 103 patients, consisting of 44 with cervical spinal myelopathy (CSM), 39 with ossification of the posterior longitudinal ligament (OPLL), and 20 with cervical disk herniation (CDH). Multivariate analyses were used to obtain correlations between CT-M findings (spinal cord area and the rate of spinal cord flatness) and clinical items (age, disease duration, preoperative JOA score, and postoperative recovery rate). There was a strong positive correlation between spinal cord area and postoperative recovery rate. Because both spinal cord area and disease duration for the CSM and OPLL groups had a strong positive correlation with the recovery rate, they were found to predict postoperative recovery. In the CDH group, there was no predictive index. Spinal cord area was more potential index than preoperative severity. Disease duration may also serve as an index complementing spinal cord area in the evaluation of postoperative recovery. (N.K.)

Using Remote Sensing to Evaluate Wetland Recovery in the Northern Tampa Bay Area Following Reduction in Groundwater Withdrawals

Science.gov (United States)

Elder, Amor

In the past, the Northern Tampa Bay Area (NTBA) wetlands saw severe declines in hydrologic conditions due to excessive groundwater withdrawal rates. Eventually these rates were reduced to allow the wetlands to recover. To monitor this recovery, the Southwest Florida Water Management district (SWFWMD) set up a fieldwork based scoring methodology, called the Wetlands Assessment Procedure (WAP). WAP has been used in many studies of the area since groundwater withdrawal reductions; with many of those studies finding the recovery to be mixed at best. However, these studies were very limited in the number of wetlands they could assess due to the limitations of fieldwork. Therefore, it was proposed that remotely sensed variables associated with water consumption and stress be used to assess the recovery of the NTBA wetlands, as remote sensing allows for efficient assessments of targets over large area. Utilizing ASTER imagery scenes from 2005 and 2014, 211 wetlands' remotely sensed responses of NDVI, Land Surface Temperature (LST), and Evapotranspiration (ET) were mapped and statistically examined for trends indicating improvement or decline. Furthermore, a subset of WAP scores for the two years were examined and compared to the remotely sensed values. The results were contradictory, with remotely sensed responses showing an improvement over the time period, WAP scores indicating a decline in hydrologic conditions, and the two methods showing little to no fit when modeled against each other. As such, it is believed at this time that the remotely sensed method is not suitable for measuring the indicators of wetland recovery used in the WAP methodology.

The Influence of the Academic Conservation Biology Literature on Endangered Species Recovery Planning

Directory of Open Access Journals (Sweden)

John Stinchcombe

2002-12-01

Full Text Available Despite the volume of the academic conservation biology literature, there is little evidence as to what effect this work is having on endangered species recovery efforts. Using data collected from a national review of 136 endangered and threatened species recovery plans, we evaluated whether recovery plans were changing in response to publication trends in four areas of the academic conservation biology literature: metapopulation dynamics, population viability analysis, conservation corridors, and conservation genetics. We detected several changes in recovery plans in apparent response to publication trends in these areas (e.g., the number of tasks designed to promote the recovery of an endangered species shifted, although these tasks were rarely assigned a high priority. Our results indicate that, although the content of endangered species recovery plans changes in response to the literature, results are not uniform across all topics. We suggest that academic conservation biologists need to address the relative importance of each topic for conservation practice in different settings. [See Erratum

Measuring the extent of overlaps in protected area designations.

Science.gov (United States)

Deguignet, Marine; Arnell, Andy; Juffe-Bignoli, Diego; Shi, Yichuan; Bingham, Heather; MacSharry, Brian; Kingston, Naomi

2017-01-01

Over the past decades, a number of national policies and international conventions have been implemented to promote the expansion of the world's protected area network, leading to a diversification of protected area strategies, types and designations. As a result, many areas are protected by more than one convention, legal instrument, or other effective means which may result in a lack of clarity around the governance and management regimes of particular locations. We assess the degree to which different designations overlap at global, regional and national levels to understand the extent of this phenomenon at different scales. We then compare the distribution and coverage of these multi-designated areas in the terrestrial and marine realms at the global level and among different regions, and we present the percentage of each county's protected area extent that is under more than one designation. Our findings show that almost a quarter of the world's protected area network is protected through more than one designation. In fact, we have documented up to eight overlapping designations. These overlaps in protected area designations occur in every region of the world, both in the terrestrial and marine realms, but are more common in the terrestrial realm and in some regions, notably Europe. In the terrestrial realm, the most common overlap is between one national and one international designation. In the marine realm, the most common overlap is between any two national designations. Multi-designations are therefore a widespread phenomenon but its implications are not well understood. This analysis identifies, for the first time, multi-designated areas across all designation types. This is a key step to understand how these areas are managed and governed to then move towards integrated and collaborative approaches that consider the different management and conservation objectives of each designation.

How carryover has an effect on recovery measures related to the area under the curve: theoretical and experimental investigations using cardiovascular parameters.

Science.gov (United States)

Sawada, Yukihiro; Kato, Yuichi

2011-03-01

This study examines cardiovascular recovery from mental stress. Investigating the absence or presence of carryover effect, the effect of the final reactivity observed at the end of stressful task on the successive recovery, was the major objective. A recently advocated recovery measure related to the area under the curve, mean recovery rate (MRR), was investigated, comparing with the two relatives of this type, total carryover (TCO) and literally area under the curve (AUC). At the onset, a detailed theoretical formulation of each measure was carried out, starting from its original definition. It was predicted that MRR, but not TCO or AUC, could be free from the carryover effect. Next, 88 male students underwent a 5-min mental arithmetic during which blood pressure and heart rate were measured. Nearly all the theoretical predictions (i.e., 5/6 for the three recovery measures by two cardiovascular parameters) were supported by experimental data. There was only one exception: for heart rate, there was a proportional relationship even for MRR versus the final reactivity. Vagal rebound in the recovery period was conceived as the main contributor of this contradiction. The implications of these results for the understanding of future directions in recovery studies are discussed.

Sustainable Rest Area Design and Operations

Science.gov (United States)

2017-10-01

One way in which State Departments of Transportation (DOTs) can modernize their rest areas while reducing operations and maintenance costs is by incorporating sustainable practices into rest area design and operations. Sustainability practices that D...

Design process of an area-efficient photobioreactor

NARCIS (Netherlands)

Zijffers, J.F.; Janssen, M.G.J.; Tramper, J.; Wijffels, R.H.

2008-01-01

This article describes the design process of the Green Solar Collector (GSC), an area-efficient photobioreactor for the outdoor cultivation of microalgae. The overall goal has been to design a system in which all incident sunlight on the area covered by the reactor is delivered to the algae at such

Study on CO{sub 2} Recovery System Design in Supercritical CO{sub 2} Cycle for SFR Application

Energy Technology Data Exchange (ETDEWEB)

Kim, Min Seok; Jung, Hwa-Young; Lee, Jeong Ik [KAIST, Daejeon (Korea, Republic of)

2016-10-15

As a part of Sodium-cooled Fast Reactor (SFR) development in Korea, the supercritical CO{sub 2} (S-CO{sub 2}) Brayton cycle is considered as an alternative power conversion system to eliminate sodium-water reaction (SWR) when the current conventional steam Rankine cycle is utilized with SFR. The parasitic loss caused by the leakage flow should be minimized since this greatly influences the cycle efficiency. Thus, a simple model for estimating the critical flow in a turbo-machinery seal was developed to predict the leakage flow rate and calculate the required total mass of working fluid in a S-CO{sub 2} power system to minimize the parasitic loss. In this work, study on CO{sub 2} recovery system design was conducted by finding the suitable recovery point with the developed simple CO{sub 2} critical flow model and sensitivity analysis was performed on the power system performance with respect to multiple CO{sub 2} recovery process options. The study of a CO{sub 2} recovery system design was conducted to minimize the thermal efficiency losses caused by CO{sub 2} inventory recovery system. For the first step, the configuration of a seal was selected. A labyrinth seal has suitable features for the S-CO{sub 2} power cycle application. Then, thermal efficiency losses with different CO{sub 2} leak rate and recovery point were evaluated. To calculate the leak rate in turbo-machinery by using the developed CO{sub 2} critical flow model, the conditions of storage tank is set to be closer to the recovery point. After modifying the critical flow model appropriately, total mass flow rate of leakage flow was calculated. Finally, the CO{sub 2} recovery system design work was performed to minimize the loss of thermal efficiency. The suggested system is not only simple and intuitive but also has relatively very low additional work loss from the compressor than other considered systems. When each leak rate is set to the conventional leakage rate of 1 kg/s per seal, the minimum and

Conceptual design of krypton recovery plant by porous membrane method

International Nuclear Information System (INIS)

Yoshida, Hiroshi; Fujine, Sachio; Shimizu, Toku; Saito, Keiichiro; Ouchi, Misao

1979-10-01

A conceptual design of a krypton recovery plant by porous membrane method was made to study feasibility of treating fuel reprocessing off-gas. Specifications of the plant could be clarified, such as off-gas pretreatment system, first cascade system of gaseous diffusion Hertz cascade composed of two-compartment diffusers, storage system, shield and housing and operating conditions. Capital costs and operating costs of the plant were estimated for different operating conditions and cost parameters. Technical and economic feasibility of the method compares favorably with those of the cryogenic distillation or the solvent absorption method. (author)

Experimental study of solvent-based emulsion injection to enhance heavy oil recovery in Alaska North Slope area

Energy Technology Data Exchange (ETDEWEB)

Qiu, F.; Mamora, D. [Texas A and M Univ., College Station, TX (United States)

2010-07-01

This study examined the feasibility of using a chemical enhanced oil recovery method to overcome some of the technical challenges associated with thermal recovery in the Alaska North Slope (ANS). This paper described the second stage research of an experimental study on nano-particle and surfactant-stabilized solvent-based emulsions for the ANS area. Four successful core flood experiments were performed using heavy ANS oil. The runs included water flooding followed by emulsion flooding; and pure emulsion injection core flooding. The injection rate and core flooding temperature remained constant and only 1 PV micro-emulsion was injected after breakthrough under water flooding or emulsion flooding. Oil recovery increased by 26.4 percent from 56.2 percent original oil in place (OOIP) with waterflooding to 82.6 percent OOIP with injection of emulsion following water flooding. Oil recovery was slightly higher with pure emulsion flooding, at 85.8 percent OOIP. The study showed that low permeability generally resulted in a higher shear rate, which is favourable for in-situ emulsification and higher displacement efficiency. 11 refs., 4 tabs., 20 figs.

From recovery to regulation: an attempt to reconceptualize 'recovery from work'.

Science.gov (United States)

Zijlstra, F R H; Cropley, M; Rydstedt, L W

2014-08-01

The concept of 'recovery' (from work) has quickly gained in importance in the occupational health literature. However, we think that the conceptualization of 'recovery' needs some more attention. Although many authors acknowledge that 'recovery' refers to a 'process', the concept is often treated as a static construct. In this paper, we argue that recovery should be conceptualized as a dynamic construct related to changes in psychophysiological state of the person. We refer to two main theories that have provided a theoretical framework for research in this area: Meijman & Mulder's Effort-Recovery (E-R) model and Hobfoll's Conservation of Resources theory. In particular, the E-R model has been seminal in this area and stresses the element of changing psychophysiological states that has been used for reconceptualising 'recovery'. Various biological rhythms influence these changing psychophysiological states, and thus the level of energy (or effort) a person can mobilize or wants to mobilize. A distinction is made between 'physical fatigue' and 'mental fatigue' and its consequences for recovery. The discrepancy between 'actual state' and 'required state' has been suggested as the basis for 'recovery'. This emphasises that recovery is a dynamic and ongoing process, which also included motivational aspects, in particular as far as mental work is concerned. The capacity to maintain self-regulation of one's psychophysiological state is important in this respect. Thus, we propose that 'recovery' is the continuous process of harmonizing the 'actual state' with the state that is 'required' at that moment. Copyright © 2014 John Wiley & Sons, Ltd.

Recovery of Areas Degraded by Mining Within the Amazon Forest: Interaction of the Physical Condition of Soil and Biological Activity

Science.gov (United States)

Ribeiro, A. I.; Mello, G. F.; Longo, R. M.; Fengler, F. H.; Peche Filho, A., Sr.

2017-12-01

One of the greatest natural riches of Brazil is the Amazon rainforest. The Amazon region is known for its abundance of mineral resources, and may include topaz, oil, and especially cassiterite. In this scope, the mining sector in Brazil has great strategic importance because it accounts for approximately 30% of the country's exports with a mineral production of 40 billion dollars (Brazilian Mining Institute, 2015). In this scenario, as a consequence of mining, the Amazonian ecosystem has been undergoing a constant process of degradation. An important artifice in the exploitation of mineral resources is the rehabilitation and/or recovery of degraded areas. This recovery requires the establishment of degradation indicators and also the quality of the soil associated with its biota, since the Amazonian environment is dynamic, heterogeneous and complex in its physical, chemical and biological characteristics. In this way, this work presupposes that it is possible to characterize the different stages of recovery of tillage floor areas in deactivated cassiterite mines, within the Amazonian forest, in order to evaluate the interactions between the level of biological activity (Serrapilheira Height, Coefficient Metabolic, Basal Breath) and physical soil characteristics (aggregate DMG, Porosity, Total Soil Density, Moisture Content), through canonical correlation analysis. The results present correlations between the groups of indicators. Thus, from the use of the groups defined by canonical correlations, it was possible to identify the response of the set of physical and biological variables to the areas at different stages of recovery.

INNOVATIVE REMEDIATION AND MONITORING SYSTEM INSIDE AN AREA USED FOR PAPER SLUDGE RECOVERY

Directory of Open Access Journals (Sweden)

Valerio Marroni

2010-12-01

Full Text Available An innovative bioremediation technology and strategy were applied to a former-quarry area in Imola (BO – Italy concerned by an incorrect environmental restoration of paper sludge, with subsequent uncontrolled biogas production and migration to the adjacent area. An Emergency Plan was implemented by the isolation of the buried sludge area and a characterization project was performed to define an appropriate permanently safe recovery. An innovative biological in situ treatment, avoiding paper sludge removal, was adopted; it was based on the use of tailored compost and enzymes to reduce methane production and concentration. This was integrated by specific monitoring piezometers for both biogas (CH4, CO2 and oxygen monthly measurements, and also the application of a respirometric technique application to buried sludge for assessing its stabilisation under aerobic and anaerobic conditions. This communication describes the strategy used, the treatment and monitoring system and the results of 3 years field pilot application. Monitoring work is still in progress.

Diagnostic instrumentation development program for the heat recovery/seed recovery system of the open-cycle, coal-fired magnetohydrodynamic power plant

International Nuclear Information System (INIS)

Murphree, D.L.; Cook, R.L.; Bauman, L.E.

1981-01-01

Highly efficient and environmentally acceptable, the coal-fired MHD power plant is an attractive facility for producing electricity. The design of its downstream system, however, presents technological risks which must be corrected if such a plant is to be commercially viable before the end of the century. The heat recovery/seed recovery system (HRSR) at its present stage is vulnerable to corrosion on the gas side of the radiant furnace, the secondary superheater, and the intermediate temperature air heater. Slagging and fouling of the heat transfer surface have yet to be eliminated. Gas chemistry, radiant heat transfer, and particulate removal are other problematic areas which are being researched in a DOE development program whose test activities at three facilities are contributing to an MHD/HRSR data base. In addition, a 20 MWt system to study HRSR design, is being now assembled in Tennessee

Techno-economic analysis and optimization of the heat recovery of utility boiler flue gas

International Nuclear Information System (INIS)

Xu, Gang; Huang, Shengwei; Yang, Yongping; Wu, Ying; Zhang, Kai; Xu, Cheng

2013-01-01

Highlights: • Four typical flue gas heat recovery schemes are quantitatively analyzed. • The analysis considers thermodynamic, heat transfer and hydrodynamics factors. • Techno-economic analysis and optimization design are carried out. • High-stage steam substitute scheme obtains better energy-saving effect. • Large heat transfer area and high flue gas resistances weaken overall performance. - Abstract: Coal-fired power plants in China consume nearly half of available coals, and the resulting CO 2 emissions cover over 40% of total national emissions. Therefore, reducing the energy expenditure of coal-fired power plants is of great significance to China’s energy security and greenhouse gas reduction programs. For coal-fired power plants, the temperature of a boiler’s exhaust gas reaches 120–150 °C or even higher. The thermal energy of boiler’s exhaust accounts for approximately 3–8% of the total energy of fuel input. Given these factors, we conducted a techno-economic analysis and optimization design of the heat recovery system using boiler exhaust gas. This research is conformed to the principles of thermodynamic, heat transfer, and hydrodynamics. Based on the data from an existing 1000 MW typical power generation unit in China, four typical flue gas heat recovery schemes are quantitatively analyzed from the thermodynamics perspective. The impacts of flue gas heat recovery on net work output and standard coal consumption rate of various schemes are performed. Furthermore, the transfer area of heat recovery exchanger and the draft fan work increment due to the flue gas pressure drop are analyzed. Finally, a techno-economic analysis of the heat recovery schemes is conducted, and some recommendations on optimization design parameters are proposed, with full consideration of various factors such as the decrease on fuel cost due to energy conservation as well as the investment cost of heat recovery retrofitting. The results revealed that, high

SolarOil Project, Phase I preliminary design report. [Solar Thermal Enhanced Oil Recovery project

Energy Technology Data Exchange (ETDEWEB)

Baccaglini, G.; Bass, J.; Neill, J.; Nicolayeff, V.; Openshaw, F.

1980-03-01

The preliminary design of the Solar Thermal Enhanced Oil Recovery (SolarOil) Plant is described in this document. This plant is designed to demonstrate that using solar thermal energy is technically feasible and economically viable in enhanced oil recovery (EOR). The SolarOil Plant uses the fixed mirror solar concentrator (FMSC) to heat high thermal capacity oil (MCS-2046) to 322/sup 0/C (611/sup 0/F). The hot fluid is pumped from a hot oil storage tank (20 min capacity) through a once-through steam generator which produces 4.8 MPa (700 psi) steam at 80% quality. The plant net output, averaged over 24 hr/day for 365 days/yr, is equivalent to that of a 2.4 MW (8.33 x 10/sup 6/ Btu/hr) oil-fired steam generator having an 86% availability. The net plant efficiency is 57.3% at equinox noon, a 30%/yr average. The plant will be demonstrated at an oilfield site near Oildale, California.

[Brain function recovery after prolonged posttraumatic coma].

Science.gov (United States)

Klimash, A V; Zhanaidarov, Z S

2016-01-01

To explore the characteristics of brain function recovery in patients after prolonged posttraumatic coma and with long-unconscious states. Eighty-seven patients after prolonged posttraumatic coma were followed-up for two years. An analysis of a clinical/neurological picture after a prolonged episode of coma was based on the dynamics of vital functions, neurological status and patient's reactions to external stimuli. Based on the dynamics of the clinical/neurological picture that shows the recovery of functions of the certain brain areas, three stages of brain function recovery after a prolonged episode of coma were singled out: brain stem areas, diencephalic areas and telencephalic areas. These functional/anatomic areas of brain function recovery after prolonged coma were compared to the present classifications.

Structuring Disaster Recovery Infrastructure Decisions: Lessons from Boulder County's 2013 Flood Recovery

Science.gov (United States)

Clavin, C.; Petropoulos, Z.

2017-12-01

Recovery phase decision making processes, as compared to mitigation and response phase decision making processes, require communities make significant financial and capital decisions in the months after a disaster. Collectively, these investments may significantly contribute to the resilience of a community to future hazards. Pre-disaster administrative decisions are well-established within existing planning processes. Post-event recovery requires community decision makers to quickly evaluate technical proposals and manage significant recovery financial resources to ensure their community rebuilds in a manner that will be more resilient to future events. These technical and administrative hurdles in the aftermath of a disaster create a challenging atmosphere to make sound, scientifically-informed decisions leading to resilient recovery. In September 2013, a 1,000-year rain event that resulted in flooding throughout the Front Range of Colorado, significantly impacting Boulder County. While the event is long past, disaster recovery efforts still continue in parts of Boulder County. Boulder County officials formed a county collaborative that adapted the NIST Community Resilience Planning Guide for Buildings and Infrastructure Systems to facilitate a goals-based multi-criteria decision making process. Rather than use hazard-based information to guide infrastructure design, the county's decision process established time-to-recovery goals for infrastructure systems that were used as criteria for project design. This presentation explores the decision-making process employed by Boulder County to specify design standards for resilient rebuilding of infrastructure systems and examine how this infrastructure planning model could be extrapolated to other situations where there is uncertainty regarding future infrastructure design standards.

Ecological distribution of pelagic copepods and species relationship to acidification, liming and natural recovery in a boreal area

Directory of Open Access Journals (Sweden)

Svein Birger WÆRVÅGEN

2003-02-01

Full Text Available Distribution and ecology of pelagic copepods were studied in a boreal area strongly affected by acidification in southern Norway. Differential regional composition of bedrock geology and Quaternary deposits combined with liming have produced aquatic sites with contrasting acidification and recovery histories. The omnivorous species Eudiaptomus gracilis showed a striking ability to tolerate both acidification and chemical recovery. The predominantly carnivorous species Heterocope saliens increased numerically during acidification, both because it is tolerant to acidic environments and because fish predation diminished or disappeared altogether. After chemical recovery, H. saliens, having an endogenous egg-bank, most readily produced viable populations with numerical abundance depending upon fish predation pressure. Thermocyclops oithonoides and Cyclops scutifer were negatively affected by strongly acidic environments, whereas Mesocyclops leuckarti tolerated acidic conditions better. All three cyclopoid species increased in abundance after chemical recovery, most probably from small residual populations. The hypolimnetic C. scutifer faced dispersal problems in re-establishing following liming. Deep lakes (>20 m harboured considerable residual populations of C. scutifer which recovered rapidly to pre-acidic conditions. Cyclops abyssorum inhabited the pelagial during early recovery of formerly chronically acidified lakes as a fugitive species, probably due to rapid dispersal capacities. Littoral cyclopoids, such as Acanthocyclops vernalis and Diacyclops nanus, were commonly distributed in the free waters of the most acidic lakes (pH = 4.5-4.8, but disappeared from the pelagial shortly after chemical recovery. The total community of pelagic copepods forms a promising tool to identify historical acidification and trajectories of recovery in the freshwater environment.

Resource Conservation and Recovery Act closure report: Area 2 Bitcutter and Postshot Containment Shops Injection Wells, Correction Action Unit 90

International Nuclear Information System (INIS)

1996-12-01

This Closure Report provides documentation of the activities conducted during the Resource Conservation and Recovery Act (RCRA) closure of the Bitcutter and Postshot Containment Shops Injection Wells located in Area 2 of the Nevada Test Site (NTS), Oak Spring Quadrangle (USGS, 1986), Township 10 South, Range 53 East, Nye County, Nevada. This report discusses the Bitcutter Shop Inside Injection Well (CAU 90-A) closure-in-place and the Bitcutter Shop Outside Injection Well (CAU 90-B) and Postshot Containment Shop Injection Well (CAU 90-C) clean closures. This Closure Report provides background information about the unit, the results of the characterization activities and actions conducted to determine the closure design. It also provides a discussion of the drainage analysis, preliminary closure activities, final closure activities, waste management activities, and the Post-Closure Care requirements

Study seeks to boost Appalachian gas recovery

International Nuclear Information System (INIS)

Land, R.

1992-01-01

Ashland Exploration Inc. and the Gas Research Institute (GRI) are trying to find ways to increase gas recovery in the Appalachian basin. They are working together to investigate Mississippian Berea sandstone and Devonian shale in a program designed to achieve better understanding and improved performance of tight natural gas formations in the area. This paper reports that three wells on Ashland Exploration acreage in Pike County, Ky., are involved in the research program. Findings from the first two wells will be used to optimize evaluation and completion of the third well. The first two wells have been drilled. Drilling of the third well was under way at last report. Ashland Exploration has been involved with GRI's Devonian shale research since 1988. GRI's initial focus was on well stimulation because Devonian shale wells it reviewed had much lower recoveries than could be expected, based on estimated gas in place. Research during the past few years was designed to improve the execution and quality control of well stimulation

A new conceptual cold-end design of boilers for coal-fired power plants with waste heat recovery

International Nuclear Information System (INIS)

Yang, Yongping; Xu, Cheng; Xu, Gang; Han, Yu; Fang, Yaxiong; Zhang, Dongke

2015-01-01

Highlights: • A new cold-end design of boilers for CFPPs with waste heat recovery is proposed. • Thermodynamic and economic analyses are quantitatively conducted. • Higher energy efficiency improvement and greater economic benefits are achieved. • Lower exergy destruction and better matched energy level are obtained. - Abstract: After conducting an in-depth analysis of the conventional boiler cold-end design for waste heat recovery, this work proposed a new conceptual boiler cold-end design integrated with the steam cycle in a 1000 MW CFPP, in which the preheating of air was divided into high-temperature air preheater (HTAP), main air preheater (MAP) and low-temperature air preheater (LTAP). The HTAP and an economizer were installed in separate flue ducts, and the low temperature economizer (LTE) was situated between the MAP and the LTAP in the main flue duct to heat the condensed water. In the proposed boiler cold-end design, the flue gas waste heat was not only used to heat condensed water, but also to further preheat the combustion air. The air temperature at the air-preheater outlet increases and part of the steam bleeds with high exergy can be saved, resulting in greater energy-savings and better economics. Results showed that, for a typical 1000 MW CFPP in China, using the proposed boiler cold-end design for waste heat recovery could produce 13.3 MW e additional net power output with a heat rate reduction of approximately 112.0 kJ/kW h and could yield a net benefit of up to $85.8 M per year, which is much greater than those of the conventional cases. Exergy destruction is also reduced from 49.9 MW th in the conventional boiler cold-end design to 39.6 MW th in the proposed design

Integrated computer-aided framework for chemical product and process application design and optimization for waste heat recovery

DEFF Research Database (Denmark)

Cignitti, Stefano; Woodley, John M.; Abildskov, Jens

2017-01-01

This contribution presents an integrated framework for product-process design. The framework integrates the two design problems into one and finds the optimal solution through simultaneous optimization. The framework consists of four hierarchical steps and uses a set of methods, tools and databases...... for property prediction, novel fluid design and mathematical programming. The application of the framework is targeted for waste heat recovery design systems, where the sensitivity of product and process design variables is high and the simultaneous design is necessary. The sustainable design solutions...... are showcased in this paper for mixed refrigeration design....

Design and implementation of disaster recovery and business continuity solution for radiology PACS.

Science.gov (United States)

Mansoori, Bahar; Rosipko, Beverly; Erhard, Karen K; Sunshine, Jeffrey L

2014-02-01

In the digital era of radiology, picture archiving and communication system (PACS) has a pivotal role in retrieving and storing the images. Integration of PACS with all the health care information systems e.g., health information system, radiology information system, and electronic medical record has greatly improved access to patient data at anytime and anywhere throughout the entire enterprise. In such an integrated setting, seamless operation depends critically on maintaining data integrity and continuous access for all. Any failure in hardware or software could interrupt the workflow or data and consequently, would risk serious impact to patient care. Thus, any large-scale PACS now have an indispensable requirement to include deployment of a disaster recovery plan to ensure secure sources of data. This paper presents our experience with designing and implementing a disaster recovery and business continuity plan. The selected architecture with two servers in each site (local and disaster recovery (DR) site) provides four different scenarios to continue running and maintain end user service. The implemented DR at University Hospitals Health System now permits continuous access to the PACS application and its contained images for radiologists, other clinicians, and patients alike.

Recovery and disposal of discarded tires in the Taiwan area.

Science.gov (United States)

Hwang, J S; Roam, G D

1994-12-01

Urbanization and industrialization has resulted in a vast amount of artificial water containers in Taiwan, especially discarded automobile tires. 3.5 million automobile tires and several million motorcycle tires are discarded annually. The discarded tires contaminate the environment and also become a substantial number of breeding sites for the dengue vector mosquitoes. In order to establish a sound system for the recovery and disposal of discarded tires and to control dengue fever through source reduction, it has been emphasized that users must pay for their waste. It is necessary to recover and properly dispose of these discarded tired. The commercial firms which sell or manufacture tires are therefore advised to cooperate with the Environmental Protection Administration of the Executive Yuan, R.O.C. and follow the "Regulations of Recovery and Disposal of Discarded Tires". They are requested to establish foundations for the recovery of discarded tires. Those who are willing to join should prepay a deposit or related charge by the size of tire, which is imported or locally manufactured. The foundation utilizes the deposits for the recovery and disposal of discarded tires. From 1991 to 1993 the commercial tire firms had already achieved the 80% recovery rates declared by the authorities concerned. Some of the tires, after having been recovered, were recycled in the original form and the rest were cut into small pieces for recycling after physical treatment. It should be mentioned that the Department of Environmental Protection of Kaohsiung City has collected 80 thousand discarded automobile tires to be used as ocean jetty.(ABSTRACT TRUNCATED AT 250 WORDS)

Loop transfer recovery for general observer architecture

DEFF Research Database (Denmark)

Niemann, Hans Henrik; Søgaard-Andersen, Per; Stoustrup, Jakob

1991-01-01

A general and concise formulation is given of the loop transfer recovery (LTR) design problem based on recovery errors. Three types of recovery errors are treated: open loop recovery, sensitivity recovery and input-output recovery errors. The three corresponding versions of the asymptotic recovery...... recovery cases. This general recovery formulation covers all known observer based compensator types as special cases. The conditions given in this setting are effectively the aim of all known LTR design methods. The recovery formulation is interpreted in terms of a modelmatching problem as well, which...... is examined by means of the Q-parametrization. It is shown how the general controller obtained by the Q-parametrization can be written as a Luenberger observer based controller. In all cases, n controller states suffice to achieve recovery. The compensators are characterized for errors both on the input...

Species-level persistence probabilities for recovery and conservation status assessment.

Science.gov (United States)

Che-Castaldo, Judy P; Neel, Maile C

2016-12-01

Recovery planning for species listed under the U.S. Endangered Species Act has been hampered by a lack of consistency and transparency, which can be improved by implementing a standardized approach for evaluating species status and developing measurable recovery criteria. However, managers lack an assessment method that integrates threat abatement and can be used when demographic data are limited. To help meet these needs, we demonstrated an approach for evaluating species status based on habitat configuration data. We applied 3 established persistence measures (patch occupancy, metapopulation capacity, and proportion of population lost) to compare 2 conservation strategies (critical habitat designated by the U.S. Fish and Wildlife Service and the Forest Service's Carbonate Habitat Management Strategy) and 2 threat scenarios (maximum limestone mining, removal of all habitat in areas with mining claims; minimum mining, removal of habitat only in areas with existing operations and high-quality ore) against a baseline of existing habitat for 3 federally listed plant species. Protecting all area within the designated critical habitat maintained a similar level (83.9-99.9%) of species persistence as the baseline, whereas maximum mining greatly reduced persistence (0.51-38.4% maintained). The 3 persistence measures provided complementary insights reflecting different aspects of habitat availability (total area, number of patches, patch size, and connectivity). These measures can be used to link recovery criteria developed following the 3 R principles (representation, redundancy, and resilience) to the resulting improvements in species viability. By focusing on amount and distribution of habitat, our method provides a means of assessing the status of data-poor species to inform decision making under the Endangered Species Act. © 2016 Society for Conservation Biology.

Recommendation of federal protected area designation for Sable Island

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-04-15

A report by the Canada - Nova Scotia Sable Island Task Group (TG) and its partners recommends the appropriate federal protected area designation for Sable Island as being either that of a national wildlife area or of a national park, and includes objectives and a synopsis of the analyses of the designation options. It was found that both protected area designations are feasible and would ensure equivalent and comprehensive conservation of the ecology and wildlife on the Island, including the horses, but the TG's preferred recommendation is the designation of Sable Island as a National Park under the Canada National Parks Act. The next steps include consultations and a review of the issues identified during these consultations to facilitate the designation.

Wide Area Recovery and Resiliency Program (WARRP) Interim Clearance Strategy for Environments Contaminated with Hazardous Chemicals

Science.gov (United States)

2012-07-01

imperative that the community address the range of values, and have agreement, before a disaster strikes. Pre-event clearance level concurrence is...on the cleanup of specific sites: those containing only cesium-137 (Goiania) and those containing 137Cs and other radionuclides ( Chernobyl ...targets and consider initiatives to enhance the quality of life of the residents of the contaminated areas. Recovery experience from the Chernobyl

Conceptual design on uranium recovery plant from seawater

International Nuclear Information System (INIS)

Kato, Toshiaki; Okugawa, Katsumi; Sugihara, Yutaka; Matsumura, Tsuyoshi

1999-01-01

Uranium containing in seawater is extremely low concentration, which is about 3 mg (3 ppb) per 1 ton of seawater. Recently, a report on development of a more effective collector of uranium in seawater (a radiation graft polymerization product of amidoxime onto polyethylene fiber) was issued by Japan Atomic Energy Research Institute. In this paper, an outline design of a uranium recovery plant from seawater was conducted on a base of the collector. As a result of cost estimation, the collection cost of seawater uranium using this method was much higher than that of uranium mine on land and described in the Red Book for mineral uranium cost. In order to make the seawater uranium cost comparable to the on-land uranium cost, it is necessary to establish comprehensive efforts in future technical development, such as development in absorption property of uranium with the collector, resolution method using less HCl, and so forth. (G.K.)

36 CFR 212.56 - Identification of designated roads, trails, and areas.

Science.gov (United States)

2010-07-01

... roads, trails, and areas. 212.56 Section 212.56 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE TRAVEL MANAGEMENT Designation of Roads, Trails, and Areas for Motor Vehicle Use § 212.56 Identification of designated roads, trails, and areas. Designated roads, trails, and areas...

P-West High Intensity Secondary Beam Area Design Report

Energy Technology Data Exchange (ETDEWEB)

Cox, A.; Currier, R.; Eartly, D.; Guthke, A.; Johnson, G.; Lee, D.; Dram, R.; Villegas, E.; Rest, J.; Tilles, E.; Vander Arend, P.

1977-03-01

This report gives the initial design parameters of a 1000 GeV High Intensity Superconducting Secondary Beam Laboratory to be situated in the Proton Area downstream of the existing Proton West experimental station. The area will provide Fermilab with a major capability for experimentation with pion and antiproton beams of intensities and of energies available at no other laboratory and with an electron beam with excellent spot size, intensity, and purity at energies far above that available at electron machines. Detailed beam design, area layouts, and cost estimates are presented, along with the design considerations.

Design and qualification of an on-line permeator for the recovery of tritium from lead-lithium eutectic breeding alloy

International Nuclear Information System (INIS)

Veredas, G.; Fradera, J.; Fernandez, I.; Batet, L.; Penalva, I.; Mesquida, L.; Abella, J.; Sempere, J.; Martinez, I.; Herrazti, B.; Sedano, L.

2011-01-01

The fast and efficient recovery of bred tritium represents a major milestone of tritium breeding technologies R and D and is key for the demonstration of fusion reactor fuel self-sufficiency. For lead-lithium eutectic, diverse technologies are currently being investigated and qualified. Permeator Against Vacuum (PAV) solution represents a firm candidate because: (i) runs as a single-step process for tritium on-line recovery, (ii) works passively allowing to be thermally governed, (iii) can be easily in-pipe integrated in Pb15.7Li loop systems and (iv) can be conceived with high compactness. An optimal design of a PAV requires a detailed hydraulic design optimization for established operational ranges. An optimal PAV design is proposed and qualified by numerical simulation.

Monitoring vegetation recovery in fire-affected areas using temporal profiles of spectral signal from time series MODIS and LANDSAT satellite images

Science.gov (United States)

Georgopoulou, Danai; Koutsias, Nikos

2015-04-01

Vegetation phenology is an important element of vegetation characteristics that can be useful in vegetation monitoring especially when satellite remote sensing observations are used. In that sense temporal profiles extracted from spectral signal of time series MODIS and LANDSAT satellite images can be used to characterize vegetation phenology and thus to be helpful for monitoring vegetation recovery in fire-affected areas. The aim of this study is to explore the vegetation recovery pattern of the catastrophic wildfires that occurred in Peloponnisos, southern Greece, in 2007. These fires caused the loss of 67 lives and were recognized as the most extreme natural disaster in the country's recent history. Satellite remote sensing data from MODIS and LANDSAT satellites in the period from 2000 to 2014 were acquired and processed to extract the temporal profiles of the spectral signal for selected areas within the fire-affected areas. This dataset and time period analyzed together with the time that these fires occurred gave the opportunity to create temporal profiles seven years before and seven years after the fire. The different scale of the data used gave us the chance to understand how vegetation phenology and therefore the recovery patterns are influenced by the spatial resolution of the satellite data used. Different metrics linked to key phenological events have been created and used to assess vegetation recovery in the fire-affected areas. Our analysis was focused in the main land cover types that were mostly affected by the 2007 wildland fires. Based on CORINE land-cover maps these were agricultural lands highly interspersed with large areas of natural vegetation followed by sclerophyllous vegetation, transitional woodland shrubs, complex cultivation patterns and olive groves. Apart of the use of the original spectral data we estimated and used vegetation indices commonly found in vegetation studies as well as in burned area mapping studies. In this study we

Designing and managing successful endangered species recovery programs

Science.gov (United States)

Clark, Tim W.; Crete, Ron; Cada, John

1989-03-01

Endangered species recovery is characterized by complexity and uncertainty in both its biological and organizational aspects. To improve performance in the organizational dimension, some models of organizations are briefly introduced with an emphasis on the organization as a system for processing information, i.e., for successfully dealing with the high uncertainty in the task environment. A strong task orientation,which rewards achievement of the primary goal, is suggested as ideal for this task, as is generative rationality, which encourages workers to observe, critique, and generate new ideas. The parallel organization—a flexible, participatory, problem-solving structure set up alongside traditional bureaucracies—is offered as a useful structure for meeting the demands of uncertainties encountered during recovery. Task forces and projects teams can be set up as parallel organizations. Improved managerial functions include coordinating roles to facilitate the flow and use of information; decision making to avoid “groupthink”—the defects, symptoms, and countermeasures are described; and productive, active management of the inevitable conflict. The inability of organizations to solve dilemmas, to examine their own structures and management, and to change themselves for more effective, efficient, and equitable performance is seen as the major obstacle to improved recovery programs. Some recommendations for effecting change in bureaucracies are made along with a call for case studies detailing the organizational dimensions of endangered species recovery programs.

Advanced heat pump for the recovery of volatile organic compounds. Phase 1, Conceptual design of an advanced Brayton cycle heat pump for the recovery of volatile organic compounds: Final report

Energy Technology Data Exchange (ETDEWEB)

1992-03-01

Emissions of Volatile Organic Compounds (VOC) from stationary industrial and commercial sources represent a substantial portion of the total US VOC emissions. The ``Toxic-Release Inventory`` of The US Environmental Protection Agency estimates this to be at about 3 billion pounds per year (1987 estimates). The majority of these VOC emissions are from coating processes, cleaning processes, polymer production, fuel production and distribution, foam blowing,refrigerant production, and wood products production. The US Department of Energy`s (DOE) interest in the recovery of VOC stems from the energy embodied in the recovered solvents and the energy required to dispose of them in an environmentally acceptable manner. This Phase I report documents 3M`s work in close working relationship with its subcontractor Nuclear Consulting Services (Nucon) for the preliminary conceptual design of an advanced Brayton cycle heat pump for the recovery of VOC. Nucon designed Brayton cycle heat pump for the recovery of methyl ethyl ketone and toluene from coating operations at 3M Weatherford, OK, was used as a base line for the work under cooperative agreement between 3M and ODE. See appendix A and reference (4) by Kovach of Nucon. This cooperative agreement report evaluates and compares an advanced Brayton cycle heat pump for solvent recovery with other competing technologies for solvent recovery and reuse. This advanced Brayton cycle heat pump is simple (very few components), highly reliable (off the shelf components), energy efficient and economically priced.

Design, Prototyping, and Assessment of a Wastewater Closed-Loop Recovery and Purification System

Directory of Open Access Journals (Sweden)

Marco Bortolini

2017-10-01

Full Text Available Efforts to decrease the water use within industry are mandatory to pursue product and process sustainability. Particularly, the European Union (EU is at the top level for water consumption in industry, while some sectors, such as the food and beverage (F&B, are highly water-intensive with hundreds of liters per hour of consumed and, then, drained water. This article provides a systematic overview of the most innovative insights coming from an EU Eco-Innovation project dealing with greening the F&B industry through the design, prototyping, technical, economic, and environmental assessment of a wastewater closed-loop recovery and purification system. The system, tailored for a standard mid-size F&B company using 2–3 billion L/year of raw water, collects, purifies and recirculates the key produced wastewater streams with an overall recovery efficiency of about 56%. The proposed purification technology comes from the most efficient combination of membrane-based filtration methods, reverse osmosis (RO, and ultraviolet modules. Evidence from the technical design, full-scale on-site technology prototyping, net-present-value (NPV analysis and system life-cycle-assessment (LCA are presented concluding about the convenience of adopting the proposed solution to reduce costs and impacts on the environment.

Optimal waste heat recovery and reuse in industrial zones

International Nuclear Information System (INIS)

Stijepovic, Mirko Z.; Linke, Patrick

2011-01-01

Significant energy efficiency gains in zones with concentrated activity from energy intensive industries can often be achieved by recovering and reusing waste heat between processing plants. We present a systematic approach to target waste heat recovery potentials and design optimal reuse options across plants in industrial zones. The approach first establishes available waste heat qualities and reuse feasibilities considering distances between individual plants. A targeting optimization problem is solved to establish the maximum possible waste heat recovery for the industrial zone. Then, a design optimization problem is solved to identify concrete waste heat recovery options considering economic objectives. The paper describes the approach and illustrates its application with a case study. -- Highlights: → Developed a systematic approach to target waste heat recovery potentials and to design optimal recovery and reuse options across plants in industrial zones. → Five stage approach involving data acquisition, analysis, assessment, targeting and design. → Targeting optimization problem establishes the maximum possible waste heat recovery and reuse limit for the industrial zone. → Design optimization problem provides concrete waste heat recovery and reuse network design options considering economic objectives.

Design of CO{sub 2} absorption plant for recovery of CO{sub 2} from flue gases of gas turbine

Energy Technology Data Exchange (ETDEWEB)

Mofarahi, Masoud [Chemical Engineering Department, Persian Gulf University, Boushehr (Iran); Khojasteh, Yaser; Khaledi, Hiwa; Farahnak, Arsalan [Delta Consultant Engineering Group, Tehran (Iran)

2008-08-15

The ongoing human-induced emission of carbon dioxide (CO{sub 2}) threatens to change the earth's climate. A major factor in global warming is CO{sub 2} emission from thermal power plants, which burn fossil fuels. One possible way of decreasing CO{sub 2} emissions is to apply CO{sub 2} removal, which involves recovering of CO{sub 2} from energy conversion processes. This study is focused on recovery of CO{sub 2} from gas turbine exhaust of Sarkhun gas refinery power station. The purpose of this study is to recover the CO{sub 2} with minimum energy requirement. Many of CO{sub 2} recovery processes from flue gases have been studied. Among all CO{sub 2} recovery processes which were studied, absorption process was selected as the optimum one, due to low CO{sub 2} concentration in flue gas. The design parameters considered in this regard, are: selection of suitable solvent, solvent concentration, solvent circulation rate, reboiler and condenser duty and number of stages in absorber and stripper columns. In the design of this unit, amine solvent such as, diethanolamine (DEA), diglycolamine (DGA), methyldiethanolamine (MDEA), and monoethanolamine (MEA) were considered and the effect of main parameters on the absorption and stripping columns is presented. Some results with simultaneous changing of the design variables have been obtained. The results show that DGA is the best solvent with minimum energy requirement for recovery of CO{sub 2} from flue gases at atmospheric pressure. (author)

Design of the target area for the National Ignition Facility

International Nuclear Information System (INIS)

Foley, R.J.; Karpenko, V.P.; Adams, C.H.

1997-01-01

The preliminary design of the target area for the National Ignition Facility has been completed. The target area is required to meet a challenging set of engineering system design requirements and user needs. The target area must provide the appropriate conditions before, during, and after each shot. The repeated introduction of large amounts of laser energy into the chamber and subsequent target emissions represent new design challenges for ICF facility design. Prior to each shot, the target area must provide the required target illumination, target chamber vacuum, diagnostics, and optically stable structures. During the shot, the impact of the target emissions on the target chamber, diagnostics, and optical elements is minimized and the workers and public are protected from excessive prompt radiation doses. After the shot, residual radioactivation is managed to allow the required accessibility. Diagnostic data is retrieved, operations and maintenance activities are conducted, and the facility is ready for the next shot. The target area subsystems include the target chamber, target positioner, structural systems, target diagnostics, environmental systems, and the final optics assembly. The engineering design of the major elements of the target area requires a unique combination of precision engineering, structural analysis, opto-mechanical design, random vibration suppression, thermal stability, materials engineering, robotics, and optical cleanliness. The facility has been designed to conduct both x- ray driven targets and to be converted at a later date for direct drive experiments. The NIF has been configured to provide a wide range of experimental environments for the anticipated user groups of the facility. The design status of the major elements of the target area is described

Observation Likelihood Model Design and Failure Recovery Scheme toward Reliable Localization of Mobile Robots

Directory of Open Access Journals (Sweden)

Chang-bae Moon

2011-01-01

Full Text Available Although there have been many researches on mobile robot localization, it is still difficult to obtain reliable localization performance in a human co-existing real environment. Reliability of localization is highly dependent upon developer's experiences because uncertainty is caused by a variety of reasons. We have developed a range sensor based integrated localization scheme for various indoor service robots. Through the experience, we found out that there are several significant experimental issues. In this paper, we provide useful solutions for following questions which are frequently faced with in practical applications: 1 How to design an observation likelihood model? 2 How to detect the localization failure? 3 How to recover from the localization failure? We present design guidelines of observation likelihood model. Localization failure detection and recovery schemes are presented by focusing on abrupt wheel slippage. Experiments were carried out in a typical office building environment. The proposed scheme to identify the localizer status is useful in practical environments. Moreover, the semi-global localization is a computationally efficient recovery scheme from localization failure. The results of experiments and analysis clearly present the usefulness of proposed solutions.

Observation Likelihood Model Design and Failure Recovery Scheme Toward Reliable Localization of Mobile Robots

Directory of Open Access Journals (Sweden)

Chang-bae Moon

2010-12-01

Full Text Available Although there have been many researches on mobile robot localization, it is still difficult to obtain reliable localization performance in a human co-existing real environment. Reliability of localization is highly dependent upon developer's experiences because uncertainty is caused by a variety of reasons. We have developed a range sensor based integrated localization scheme for various indoor service robots. Through the experience, we found out that there are several significant experimental issues. In this paper, we provide useful solutions for following questions which are frequently faced with in practical applications: 1 How to design an observation likelihood model? 2 How to detect the localization failure? 3 How to recover from the localization failure? We present design guidelines of observation likelihood model. Localization failure detection and recovery schemes are presented by focusing on abrupt wheel slippage. Experiments were carried out in a typical office building environment. The proposed scheme to identify the localizer status is useful in practical environments. Moreover, the semi-global localization is a computationally efficient recovery scheme from localization failure. The results of experiments and analysis clearly present the usefulness of proposed solutions.

Recovery in soccer : part ii-recovery strategies.

Science.gov (United States)

Nédélec, Mathieu; McCall, Alan; Carling, Chris; Legall, Franck; Berthoin, Serge; Dupont, Gregory

2013-01-01

now do not significantly accelerate the return to initial levels of performance in comparison with a control condition. In conclusion, scientific evidence to support the use of strategies commonly used during recovery is lacking. Additional research is required in this area in order to help practitioners establish an efficient recovery protocol immediately after matchplay, but also for the following days. Future studies could focus on the chronic effects of recovery strategies, on combinations of recovery protocols and on the effects of recovery strategies inducing an anti-inflammatory or a pro-inflammatory response.

Soot blowing methods and soot steam consumption in Swedish recovery boilers; Sotningsmetoder och sotaangfoerbrukning i svenska sodapannor

Energy Technology Data Exchange (ETDEWEB)

Svedin, Kristoffer; Wallin, Erik; Ahlroth, Mikael

2008-09-15

The aim with the report was to put together a description of the current state of the sootblowing systems at Swedish recovery boilers, and to explain differences in cleanability and sootblowing efficiency. In chapter 4 a summary of new techniques and alternative soot blowing methods is found. The report is intended for persons working in the pulp industry. To facilitate the benchmarking the recovery boilers have been divided into two groups. Group A comprises recovery boilers which only have one stop per year and the remaining recovery boilers with more than one stop are classified into group B. The following conclusions, based on the recovery boiler design specifications, are of importance to achieve high boiler availability: Low furnace load; High recovery boiler, wide furnace bottom area; Modern air ports; Small or no correlation between cross pitch division in heat surfaces and cleanability could be seen. The expectation was to identify such a relation. However there are doubts on the correctness in reported data. The amount of chlorine and potassium is assumed to affect the cleanability for a few recovery boilers, but for the majority the amounts are low and most likely do not impact the operation. Because of the large impact of the recovery boilers design data (furnace area, load etc.) on the sootblowing, it has been hard to identify the relation cleanability contra sootblowing system. The relations that could be seen are: No distinction between normally designed nozzles and 'high efficiency' nozzles could be identified. The operational conditions for the different models differ a lot and the effect of nozzle type could not be distinguished. Only a minority of the soot blowing sequences are known from the study. In the recovery boilers with problematic areas improvements can be made in the soot blowing sequence. Four recovery boilers are using intelligent soot blowing of some kind. Two of these boilers have low availability and the other two have

36 CFR 212.51 - Designation of roads, trails, and areas.

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Designation of roads, trails... AGRICULTURE TRAVEL MANAGEMENT Designation of Roads, Trails, and Areas for Motor Vehicle Use § 212.51 Designation of roads, trails, and areas. (a) General. Motor vehicle use on National Forest System roads, on...

Science summary in support of Manatee Protection Area (MPA) design in Puerto Rico

Science.gov (United States)

Drew, C. Ashton; Alexander-Vaughn, Louise B.; Collazo, Jaime A.

2012-01-01

The Antillean manatee (Trichechus manatus manatus), a subspecies of the West Indian manatee, is listed as endangered by the US Department of Interior. In accordance with its listing, the U.S. Fish and Wildlife Service’s Caribbean Field Office (USFWS) is mandated to create one or more Manatee Protection Areas (MPAs) for Puerto Rico. Designation of these areas must comply with the legal definition of an MPA’s purpose: to prevent or reduce take of manatees (CFR 50: 44 FR 60964, Oct. 22, 1979). To meet this goal, we pursued two objectives: 1) identify areas which include the specific ecological attributes necessary to support manatee populations, and 2) identify areas where take can be reduced through approved MPA regulatory frameworks. We achieved these objectives through literature review, expert elicitation, and geospatial modeling. This report delivers to USFWS a set of nine potential MPA regions. These regions represent the spatial realization of experts’ hypotheses regarding manatee requirements and threats, and the potential to implement MPA strategies (e.g. watercraft access, speed regulations, signage and boater education). The nine regions are compared based on a number of factors, including their potential to reduce take, quality of the habitat encompassed, and total area. These maps and statistics serve as suitable starting points to select one or more MPA sites, but we recommend that the mapped attributes and threats (i.e., boating activity) of MPAs be ground-truthed to visually confirm the local presence of resources, threats, and manatees before any area is selected. Once established, the effectiveness of MPAs can be monitored and updated through processes of adaptive monitoring and management. Aerial surveys, radio tracking studies, and public surveys are all valuable tools to assess the success of an MPA. Establishing MPAs is a management action that, integrated within the species Recovery Plan, should enhance the conservation of manatees.

Error Recovery in the Time-Triggered Paradigm with FTT-CAN.

Science.gov (United States)

Marques, Luis; Vasconcelos, Verónica; Pedreiras, Paulo; Almeida, Luís

2018-01-11

Data networks are naturally prone to interferences that can corrupt messages, leading to performance degradation or even to critical failure of the corresponding distributed system. To improve resilience of critical systems, time-triggered networks are frequently used, based on communication schedules defined at design-time. These networks offer prompt error detection, but slow error recovery that can only be compensated with bandwidth overprovisioning. On the contrary, the Flexible Time-Triggered (FTT) paradigm uses online traffic scheduling, which enables a compromise between error detection and recovery that can achieve timely recovery with a fraction of the needed bandwidth. This article presents a new method to recover transmission errors in a time-triggered Controller Area Network (CAN) network, based on the Flexible Time-Triggered paradigm, namely FTT-CAN. The method is based on using a server (traffic shaper) to regulate the retransmission of corrupted or omitted messages. We show how to design the server to simultaneously: (1) meet a predefined reliability goal, when considering worst case error recovery scenarios bounded probabilistically by a Poisson process that models the fault arrival rate; and, (2) limit the direct and indirect interference in the message set, preserving overall system schedulability. Extensive simulations with multiple scenarios, based on practical and randomly generated systems, show a reduction of two orders of magnitude in the average bandwidth taken by the proposed error recovery mechanism, when compared with traditional approaches available in the literature based on adding extra pre-defined transmission slots.

Area balance and strain in an extensional fault system: Strategies for improved oil recovery in fractured chalk, Gilbertown Field, southwestern Alabama. Annual report, March 1996--March 1997

Energy Technology Data Exchange (ETDEWEB)

Pashin, J.C.; Raymond, D.E.; Rindsberg, A.K.; Alabi, G.G.; Groshong, R.H.

1997-08-01

Gilbertown Field is the oldest oil field in Alabama and produces oil from chalk of the Upper Cretaceous Selma Group and from sandstone of the Eutaw Formation along the southern margin of the Gilbertown fault system. Most of the field has been in primary recovery since establishment, but production has declined to marginally economic levels. This investigation applies advanced geologic concepts designed to aid implementation of improved recovery programs. The Gilbertown fault system is detached at the base of Jurassic salt. The fault system began forming as a half graben and evolved in to a full graben by the Late Cretaceous. Conventional trapping mechanisms are effective in Eutaw sandstone, whereas oil in Selma chalk is trapped in faults and fault-related fractures. Burial modeling establishes that the subsidence history of the Gilbertown area is typical of extensional basins and includes a major component of sediment loading and compaction. Surface mapping and fracture analysis indicate that faults offset strata as young as Miocene and that joints may be related to regional uplift postdating fault movement. Preliminary balanced structural models of the Gilbertown fault system indicate that synsedimentary growth factors need to be incorporated into the basic equations of area balance to model strain and predict fractures in Selma and Eutaw reservoirs.

Battleground Energy Recovery Project

Energy Technology Data Exchange (ETDEWEB)

Bullock, Daniel [USDOE Gulf Coast Clean Energy Application Center, Woodlands, TX (United States)

2011-12-31

In October 2009, the project partners began a 36-month effort to develop an innovative, commercial-scale demonstration project incorporating state-of-the-art waste heat recovery technology at Clean Harbors, Inc., a large hazardous waste incinerator site located in Deer Park, Texas. With financial support provided by the U.S. Department of Energy, the Battleground Energy Recovery Project was launched to advance waste heat recovery solutions into the hazardous waste incineration market, an area that has seen little adoption of heat recovery in the United States. The goal of the project was to accelerate the use of energy-efficient, waste heat recovery technology as an alternative means to produce steam for industrial processes. The project had three main engineering and business objectives: Prove Feasibility of Waste Heat Recovery Technology at a Hazardous Waste Incinerator Complex; Provide Low-cost Steam to a Major Polypropylene Plant Using Waste Heat; and Create a Showcase Waste Heat Recovery Demonstration Project.

Investigation and optimization of the depth of flue gas heat recovery in surface heat exchangers

Science.gov (United States)

Bespalov, V. V.; Bespalov, V. I.; Melnikov, D. V.

2017-09-01

Economic issues associated with designing deep flue gas heat recovery units for natural gas-fired boilers are examined. The governing parameter affecting the performance and cost of surface-type condensing heat recovery heat exchangers is the heat transfer surface area. When firing natural gas, the heat recovery depth depends on the flue gas temperature at the condenser outlet and determines the amount of condensed water vapor. The effect of the outlet flue gas temperature in a heat recovery heat exchanger on the additionally recovered heat power is studied. A correlation has been derived enabling one to determine the best heat recovery depth (or the final cooling temperature) maximizing the anticipated reduced annual profit of a power enterprise from implementation of energy-saving measures. Results of optimization are presented for a surface-type condensing gas-air plate heat recovery heat exchanger for the climatic conditions and the economic situation in Tomsk. The predictions demonstrate that it is economically feasible to design similar heat recovery heat exchangers for a flue gas outlet temperature of 10°C. In this case, the payback period for the investment in the heat recovery heat exchanger will be 1.5 years. The effect of various factors on the optimal outlet flue gas temperature was analyzed. Most climatic, economical, or technological factors have a minor effect on the best outlet temperature, which remains between 5 and 20°C when varying the affecting factors. The derived correlation enables us to preliminary estimate the outlet (final) flue gas temperature that should be used in designing the heat transfer surface of a heat recovery heat exchanger for a gas-fired boiler as applied to the specific climatic conditions.

Selection and application of effective LNAPL recovery techniques

International Nuclear Information System (INIS)

Fulton, D.E.

1996-01-01

The accumulation of light non-aqueous phase liquids (LNAPL) such as gasoline, diesel, fuel oil and lubricating oil resulting from historical or catastrophic releases, is present at numerous industrial and hazardous waste sites. Initiating LNAPL removal is the first step in remediating impacted groundwater with the LNAPL recovery process having a profound effect on the ability to cost effectively achieve site closure. In many cases, LNAPL recovery precedes full-scale groundwater design activities or even final site characterization due to regulatory compliance issues. Therefore, the timely and effective implementation of a LNAPL recovery system can result in reduced project costs by mitigating further plume migration, achieving maximum volume of recoverable hydrocarbons, eliminating the source area associated with dissolved phase contamination, and allowing comprehensive groundwater remediation to be employed sooner. Effective LNAPL recovery systems begin with evaluating a number of site-specific parameters to quantify the physical characteristics of the type of LNAPL to be recovered, the hydrogeological environment, LNAPL, plume geometry, and the specified client or regulatory cleanup goals. These parameters are discussed along with their significance in developing a conceptual understanding of the site

Design and Control of a Multi-Functional Energy Recovery Power Accumulator Battery Pack Testing System for Electric Vehicles

Directory of Open Access Journals (Sweden)

Bo Long

2014-03-01

Full Text Available In this paper, aiming at the energy loss and harmonic problems in the conventional power accumulator battery pack testing system (PABPTS, an improved multi-functional energy recovery PABPTS (ERPABPTS for electric vehicles (EVs was proposed. The improved system has the functions of harmonic detection, suppression, reactive compensation and energy recovery. The ERPABPTS, which contains a bi-directional buck-boost direct current (DC-DC converter and a bi-directional alternating current (AC-DC converter with an inductor-capacitor-inductor (LCL type filter interfacing to the AC-grid, is proposed. System configuration and operation principle of the combined system are discussed first, then, the reactive compensation and harmonic suppression controller under balanced grid-voltage condition are presented. Design of a fourth order band-pass Butterworth filter for current harmonic detection is put forward, and the reactive compensator design procedure considering the non-linear load is also illustrated. The proposed scheme is implemented in a 175-kW prototype in the laboratory. Simulation and experimental results show that the combined configuration can effectively realize energy recovery for high accuracy current test requirement, meanwhile, can effectively achieve reactive compensation and current harmonic suppression.

Perennial grasses for recovery of the aggregation capacity of a reconstructed soil in a coal mining area in southern Brazil

Directory of Open Access Journals (Sweden)

Lizete Stumpf

2014-02-01

Full Text Available The construction of a soil after surface coal mining involves heavy machinery traffic during the topographic regeneration of the area, resulting in compaction of the relocated soil layers. This leads to problems with water infiltration and redistribution along the new profile, causing water erosion and consequently hampering the revegetation of the reconstructed soil. The planting of species useful in the process of soil decompaction is a promising strategy for the recovery of the soil structural quality. This study investigated the influence of different perennial grasses on the recovery of reconstructed soil aggregation in a coal mining area of the Companhia Riograndense de Mineração, located in Candiota-RS, which were planted in September/October 2007. The treatments consisted of planting: T1- Cynodon dactylon cv vaquero; T2 - Urochloa brizantha; T3 - Panicum maximun; T4 - Urochloa humidicola; T5 - Hemarthria altissima; T6 - Cynodon dactylon cv tifton 85. Bare reconstructed soil, adjacent to the experimental area, was used as control treatment (T7 and natural soil adjacent to the mining area covered with native vegetation was used as reference area (T8. Disturbed and undisturbed soil samples were collected in October/2009 (layers 0.00-0.05 and 0.10-0.15 m to determine the percentage of macro- and microaggregates, mean weight diameter (MWD of aggregates, organic matter content, bulk density, and macro- and microporosity. The lower values of macroaggregates and MWD in the surface than in the subsurface layer of the reconstructed soil resulted from the high degree of compaction caused by the traffic of heavy machinery on the clay material. After 24 months, all experimental grass treatments showed improvements in soil aggregation compared to the bare reconstructed soil (control, mainly in the 0.00-0.05 m layer, particularly in the two Urochloa treatments (T2 and T4 and Hemarthria altissima (T5. However, the great differences between the

MULTICOMPONENT SEISMIC ANALYSIS AND CALIBRATION TO IMPROVE RECOVERY FROM ALGAL MOUNDS: APPLICATION TO THE ROADRUNNER/TOWAOC AREA OF THE PARADOX BASIN, UTE MOUNTAIN UTE RESERVATION, COLORADO

International Nuclear Information System (INIS)

Paul La Pointe; Claudia Rebne; Steve Dobbs

2004-01-01

This report describes the results made in fulfillment of contract DE-FG26-02NT15451, ''Multicomponent Seismic Analysis and Calibration to Improve Recovery from Algal Mounds: Application to the Roadrunner/Towaoc Area of the Paradox Basin, Ute Mountain Ute Reservation, Colorado'', for the Second Biennial Report covering the time period May 1, 2003 through October 31, 2003. During this period, the project achieved two significant objectives: completion of the acquisition and processing design and specifications 3D9C seismic acquisition and the 3D VSP log; and completion of the permitting process involving State, Tribal and Federal authorities. Successful completion of these two major milestones pave the way for field acquisition as soon as weather permits in the Spring of 2004. This report primarily describes the design and specifications for the VSP and 3D9C surveys

Integrated head area design of KNGR to reduce refueling outage duration

Energy Technology Data Exchange (ETDEWEB)

Jeong, Woo Tae; Park, Chi Yong; Kim, In Hwan; Kim, Dae Woong [Korea Electric Power Research Institute, Taejon (Korea, Republic of)

1998-12-31

In the design of KNGR (Korea Next Generation Reactor), we believe that economy is one of the most important factors to be considered. Thus, we reviewed and evaluated the consequences of designing the head area into an integrated package from an economical point of view. The refueling outage durations of the nuclear power plants currently in operation in Korea, some having and others not having integrated head package, are compared. This paper discusses the characteristics of head area design and the critical design issues of KNGR head area to evaluate the effect of the head area characteristics on the outage duration. 8 refs., 4 figs. (Author)

Integrated head area design of KNGR to reduce refueling outage duration

Energy Technology Data Exchange (ETDEWEB)

Jeong, Woo Tae; Park, Chi Yong; Kim, In Hwan; Kim, Dae Woong [Korea Electric Power Research Institute, Taejon (Korea, Republic of)

1997-12-31

In the design of KNGR (Korea Next Generation Reactor), we believe that economy is one of the most important factors to be considered. Thus, we reviewed and evaluated the consequences of designing the head area into an integrated package from an economical point of view. The refueling outage durations of the nuclear power plants currently in operation in Korea, some having and others not having integrated head package, are compared. This paper discusses the characteristics of head area design and the critical design issues of KNGR head area to evaluate the effect of the head area characteristics on the outage duration. 8 refs., 4 figs. (Author)

Design principles of water sensitive in settlement area on the river banks

Science.gov (United States)

Ryanti, E.; Hasriyanti, N.; Utami, W. D.

2018-03-01

This research will formulate the principle of designing settlement area of Kapuas River Pontianak with the approach of water sensitive concept of urban design (WSUD) the densely populated settlement area. By using a case study the approach that is a dense settlement area located on the banks of the river with literature study techniques to formulate the aspects considered and components that are set in the design, descriptive analysis with the rationalistic paradigm for identification characteristics of the settlement in the river banks areas with consideration of WSUD elements and formulate the principles of designing water-sensitive settlement areas. This research is important to do because the problems related to the water management system in the existing riverside settlement in Pontianak has not been maximal to do. So the primary of this research contains several objectives that will be achieved that is identifying the characteristics of riverside settlement area based on consideration of design aspects of the area that are sensitive to water and the principle of designing the area so that the existing problem structure will be formulated in relation to the community’s need for infrastructure in settlement environment and formulate and develop appropriate technology guidelines for integrated water management systems in riverside settlement areas and design techniques for water-sensitive settlements (WSUD).

Computer aided design of operational units for tritium recovery from Li17Pb83 blanket of a DEMO fusion reactor

International Nuclear Information System (INIS)

Malara, C.; Viola, A.

1995-01-01

The problem of tritium recovery from Li 17 Pb 83 blanket of a DEMO fusion reactor is analyzed with the objective of limiting tritium permeation into the cooling water to acceptable levels. To this aim, a mathematical model describing the tritium behavior in blanket/recovery unit circuit has been formulated. By solving the model equations, tritium permeation rate into the cooling water and tritium inventory in the blanket are evaluated as a function of dimensionless parameters describing the combined effects of overall resistance for tritium transfer from Li 17 Pb 83 alloy to cooling water, circulating rate of the molten alloy in blanket/recovery unit circuit and extraction efficiency of tritium recovery unit. The extraction efficiency is, in turn, evaluated as a function of the operating conditions of recovery unit. The design of tritium recovery unit is then optimized on the basis of the above parametric analysis and the results are herein reported and discussed for a tritium permeation limit of 10 g/day into the cooling water. 14 refs., 9 figs., 2 tabs

A regional synergy approach to energy recovery: The case of the Kwinana industrial area, Western Australia

International Nuclear Information System (INIS)

Beers, D. van; Biswas, W.K.

2008-01-01

Energy is a key issue in the Kwinana industrial area, Western Australia's major heavy industrial region, where the major energy consuming industries consume upto 80 PJ/yr of energy in their processes. Over the past decade, significant progress has been made towards the reduction of energy consumption and reduction of greenhouse gases in Kwinana. One way to further advance sustainable energy use is through the realisation of regional synergies. These concern the capture, recovery and reuse of by-products, water and energy between industries in close proximity. Kwinana is recognised as a leading edge example in regional synergy development, but more synergy opportunities appear to exist. The centre for sustainable resource processing (CSRP) is undertaking research to develop new synergies in Kwinana, including energy utility synergies. As part of the research, a methodology was developed and applied to identify and evaluate the economic, technical, and environmental feasibility of collaborative energy recovery opportunities from industry flue gases in Kwinana. The trial application demonstrated the significant potential to mitigate CO 2 emissions through energy recovery from flue gases by applying technologies to convert the embedded energy into useful thermal and electric applications. This article discusses the methodology and outcomes from the trial applications, including the impact of carbon taxes, reducing costs of emerging technologies, and increasing energy prices

Race-related differences in depression onset and recovery in older persons over time: the Health, Aging, and Body Composition study

NARCIS (Netherlands)

Barry, L.C.; Thorpe, R.J.; Penninx, B.W.J.H.; Yaffe, K.; Wakefield, D.; Ayonayon, H.N.; Satterfield, S.; Newman, A.B.; Simonsick, E.M.

2014-01-01

Objectives: To evaluate race-related differences in depression onset and recovery in older persons, overall and by sex, and examine race-related differences in mortality according to depression. Design: Prospective cohort study. Setting: General community in pre-designated zip code areas in Memphis,

Chemical mass balance modeling for air quality analysis near a waste-to-energy facility in a complex urban area: Program design

International Nuclear Information System (INIS)

Wells, R.; Watson, J.

1997-01-01

This paper describes the design and implementation of an ambient monitoring and receptor modeling study to evaluate air quality impacts from a state-of-the-art municipal waste management facility in a major urban area. The Robbins Resource Recovery Facility (RRRF), located in the Chicago metropolitan area, processes municipal solid waste (MSW) to recover recyclables, process the residual waste to create refuse-derived fuel (RDF), and burns the RDF to reduce the residual waste volume and recover energy. The RRRF is cooperating with the Illinois Environmental Protection Agency (IEPA) and the Illinois Office of the Attorney General (OAG) to analyze air quality and facility impacts in the plant vicinity. An ambient monitoring program began one year before plant operation and will continue for five years after startup. Because the impacts of the RRRF are projected to be very low, and because the Chicago area includes a complex mix of existing industrial, commercial, and residential activity, the ambient data will be analyzed using Version 7.0 of the USEPA s Chemical Mass Balance (CMB) model to estimate the extent of the RRRF's impact on air quality in the area. The first year of pre-operational ambient data is currently under analysis. This paper describes the study design considerations, ambient monitoring program, emission data acquisition, background source data needs, and data analysis procedures developed to conduct CMB modeling in a complex industrialized area

Actinide recovery from waste and low-grade sources

International Nuclear Information System (INIS)

Navratil, J.D.; Schulz, W.W.

1982-01-01

Actinide and nuclear fuel cycle operations generate a variety of process waste streams. New methods are needed to remove and recover actinides. More interest is also being expressed in recovering uranium from oceans, phosphoric acid, and other low grade sources. To meet the need for an up-to-date status report in the area of actinide recovery from waste and low grade sources, these papers were brought together. The papers provide an authoritative, in-depth coverage of an important area of nuclear and industrial and engineering chemistry which cover the following topics: uranium recovery from oceans and phosphoric acid; recovery of actinides from solids and liquid wastes; plutonium scrap recovery technology; and other new developments in actinide recovery processes

15 CFR 971.503 - Diligent commercial recovery.

Science.gov (United States)

2010-01-01

... ENVIRONMENTAL DATA SERVICE DEEP SEABED MINING REGULATIONS FOR COMMERCIAL RECOVERY PERMITS Resource Development... expenditures for commercial recovery by the permittee, taking into account the size of the area of the deep... required to initiate commercial recovery of hard mineral resources within the time limit established by the...

Business recovery: an assessment framework.

Science.gov (United States)

Stevenson, Joanne R; Brown, Charlotte; Seville, Erica; Vargo, John

2018-07-01

This paper presents a Business Recovery Assessment Framework (BRAF) to help researchers and practitioners design robust, repeatable, and comparable studies of business recovery in various post-disruption contexts. Studies assessing business recovery without adequately considering the research aims, recovery definitions, and indicators can produce misleading findings. The BRAF is composed of a series of steps that guide the decisions that researchers need to make to ensure: (i) that recovery is indeed being measured; (ii) that the indicators of recovery that are selected align with the objectives of the study and the definition of recovery; and, where necessary, (iii) that appropriate comparative control variables are in place. The paper draws on a large dataset of business surveys collected following the earthquakes in Canterbury, New Zealand, on 4 September 2010 and 22 February 2011 to demonstrate the varied conclusions that different recovery indicators can produce and to justify the need for a systematic approach to business recovery assessments. © 2018 The Author(s). Disasters © Overseas Development Institute, 2018.

36 CFR 212.55 - Criteria for designation of roads, trails, and areas.

Science.gov (United States)

2010-07-01

... roads, trails, and areas. 212.55 Section 212.55 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE TRAVEL MANAGEMENT Designation of Roads, Trails, and Areas for Motor Vehicle Use § 212.55 Criteria for designation of roads, trails, and areas. (a) General criteria for designation of...

Beam-dynamics driven design of the LHeC energy-recovery linac

Science.gov (United States)

Pellegrini, Dario; Latina, Andrea; Schulte, Daniel; Bogacz, S. Alex

2015-12-01

The LHeC is envisioned as a natural upgrade of the LHC that aims at delivering an electron beam for collisions with the existing hadronic beams. The current baseline design for the electron facility consists of a multipass superconducting energy-recovery linac (ERL) operating in a continuous wave mode. The unprecedently high energy of the multipass ERL combined with a stringent emittance dilution budget poses new challenges for the beam optics. Here, we investigate the performances of a novel arc architecture based on a flexible momentum compaction lattice that mitigates the effects of synchrotron radiation while containing the bunch lengthening. Extensive beam-dynamics investigations have been performed with placet2, a recently developed tracking code for recirculating machines. They include the first end-to-end tracking and a simulation of the machine operation with a continuous beam. This paper briefly describes the Conceptual Design Report lattice, with an emphasis on possible and proposed improvements that emerged from the beam-dynamics studies. The detector bypass section has been integrated in the lattice, and its design choices are presented here. The stable operation of the ERL with a current up to ˜150 mA in the linacs has been validated in the presence of single- and multibunch wakefields, synchrotron radiation, and beam-beam effects.

Integrated structural design of nuclear power plants for high seismic areas

International Nuclear Information System (INIS)

Rieck, P.J.

1979-01-01

A design approach which structurally interconnects NPP buildings to be located in high seismic areas is described. The design evolution of a typical 600 MWe steel cylindrical containment PWR is described as the plant is structurally upgraded for higher seismic requirements, while maintaining the original plant layout. The plant design is presented as having separate reactor building and auxiliary structures for a low seismic area (0.20 g) and is structurally combined at the foundation for location in a higher seismic area (0.30 g). The evolution is completed by a fully integrated design which structurally connects the reactor building and auxiliary structures at superstructure elevations as well as foundation levels for location in very severe seismic risk areas (0.50 g). (orig.)

Conditioning of red mud for subsequent titanium and scandium recovery. A conceptual design study

Energy Technology Data Exchange (ETDEWEB)

Alkan, G.; Xakalashe, B.; Kaussen, F.; Friedrich, Bernd [RWTH Aachen Univ. (Germany). IME Inst. of Process Metallurgy and Metal Recycling; Yagmurlu, B. [RWTH Aachen Univ. (Germany). IME Inst. of Process Metallurgy and Metal Recycling; MEAB Chemie Technik GmbH, Aachen (Germany)

2017-03-15

Leaching experiments were undertaken on red mud materials (red mud and red mud slag). The red mud slag was produced via the carbothermic reduction of red mud at high temperatures (T > 1500 C) via SAF treatment. Furthermore, iron was recovered in the smelting step to the metal phase. Ti and Sc were successfully recovered from the red mud materials by hydrometallurgical treatment. For both critical metals, it was found that sulfuric acid was the best mineral acid among others. Since direct red mud leaching had some shortcomings, a route designed to overcome them is proposed. For optimal Ti and Sc recovery from red mud a promising process flowsheet combining pyrometallurgical and hydrometallurgical treatment is proposed as follows: pyrometallurgical processing (fluxed smelting to produce calcium oxide based slag phases and controlled cooling for crystalline and glassy slags), leaching for maximized Ti- and Sc extraction and followed by a multistage precipitation (for metal recovery and solution purification). Initial trial results showed that the proposed process is promising.

Electrode Induced Removal and Recovery of Uranium (VI) from Acidic Subsurfaces

Energy Technology Data Exchange (ETDEWEB)

Gregory, Kelvin [Carnegie Mellon University

2013-08-12

The overarching objective of this research is to provide an improved understanding of how aqueous geochemical conditions impact the removal of U and Tc from groundwater and how engineering design may be utilized to optimize removal of these radionuclides. Experiments were designed to address the unique conditions in Area 3 of ORNL while also providing broader insight into the geochemical effectors of the removal rates and extent for U and Tc. The specific tasks of this work were to: 1) quantify the impact of common aqueous geochemical and operational conditions on the rate and extent of U removal and recovery from water, 2) investigate the removal of Tc with polarized graphite electrode, and determine the influence of geochemical and operational conditions on Tc removal and recovery, 3) determine whether U and Tc may be treated simultaneous from Area 3 groundwater, and examine the bench-scale performance of electrode-based treatment, and 4) determine the capacity of graphite electrodes for U(VI) removal and develop a mathematical, kinetic model for the removal of U(VI) from aqueous solution. Overall the body of work suggests that an electrode-based approach for the remediation of acidic subsurface environments, such as those observed in Area 3 of ORNL may be successful for the removal for both U(VI) and Tc. Carbonaceous (graphite) electrode materials are likely to be the least costly means to maximize removal rates and efficiency by maximizing the electrode surface area.

Control Structure Design of an Innovative Enhanced Biological Nutrient Recovery Activated Sludge System Coupled with a Photobioreactor

DEFF Research Database (Denmark)

Valverde Perez, Borja; Fuentes-Martínez, José Manuel; Flores Alsina, Xavier

2015-01-01

The TRENS system is a train of biological units designed for resource recovery from wastewater. It is a sequence of a modified enhanced biological phosphorus removal and recovery system (EBP2R) coupled with a photobioreactor (PBR). The bacteria-based system constructs an optimal culture media...... for the downstream algae cultivation. In this work, we present a control strategy to ensure an optimal nutrient balance to feed to the PBR, so the grown algal suspension is suitable for fertigation (irrigation and fertilization of agricultural crops). The system is able to recover up to 75% of the influent load......, while keeping an optimal N-to-P ratio of 16 in the influent to the PBR. The system is tested under different scenarios, where the influent quality is disturbed following a step change. The control system is able to reject most of the disturbances. However, when the P-recovery is limited by the bacteria...

Design of movable fixed area γ dose rate monitor

International Nuclear Information System (INIS)

Li Dongyu; Cheng Wen; Li Jikai; Huang Hong; Shen Qiming; Zhang Qiang; Liu Zhengshan

2005-10-01

Movable fixed area γ dose rate monitor has not only the characteristics of fixed area γ dose rate monitor, but that of portable meter as well. Its main function is to monitor the areas where dose rate would change without orderliness to prevent unplanned radiation exposure accidents from happening. The design way of the monitor, the main indicators description, the working principle and the comprising of software and hardware are briefly introduced. The monitor has the characteristics of simple installation, easy maintenance, little power consumption, wide range, notability of visual and audible alarm and so on. Its design and technique have novelty and advancement. (authors)

ICPP custom dissolver explosion recovery

International Nuclear Information System (INIS)

Demmer, R.; Hawk, R.

1992-01-01

This paper discusses the recovery from the February 9, 1991, small scale explosion in a custom processing dissolver at the Idaho Chemical Processing Plant (ICPP) a Department of Energy facility at the Idaho National Engineering Laboratory. The custom processing facility is a limited production area designed to recover unirradiated uranium fuel. A small amount of the nuclear material received and stored at the ICPP is unique and incompatible with the major head end dissolution processes. Custom processing is a small scale dissolution facility for processing these materials in an economical fashion in the CPP-627 hot chemistry laboratory. Two glass dissolvers were contained in a large walk in hood area. Utilities for dissolution and connections to the major ICPP uranium separation facility were provided. The fuel processing operations during this campaign involved dissolving uranium metal, uranium oxides, and uranium/fissium alloy in nitric acid

Building addiction recovery capital through online participation in a recovery community.

Science.gov (United States)

Bliuc, Ana-Maria; Best, David; Iqbal, Muhammad; Upton, Katie

2017-11-01

This study examines how online participation in a community of recovery contributes to personal journeys of recovery. It investigates whether recovery capital building - as indicated by increased levels and quality of online social interactions - and markers of positive identity development predict retention in a recovery program designed around fostering community involvement for early stage recovery addicts. It was predicted that online participation on the group's Facebook page and positive identity development are associated to retention in the program. To map how participants interact online, social network analysis (SNA) based on naturally occurring online data (N = 609) on the Facebook page of a recovery community was conducted. Computerised linguistic analyses evaluated sentiment of the textual data (capturing social identity markers). Linear regression analyses evaluated whether indicators of recovery capital predict program retention. To illustrate the findings in the context of the specific recovery community, presented are two case studies of key participants who moved from the periphery to the centre of the social network. By conducting in-depth interviews with these participants, personal experiences of engagement in the online community of group members who have undergone the most significant changes since joining the community are explored. Retention in the program was determined by a) the number of comment 'likes' and all 'likes' received on the Facebook page; b) position in the social network (degree of centrality); and c) linguistic content around group identity and achievement. Positive online interactions between members of recovery communities support the recovery process through helping participants to develop recovery capital that binds them to groups supportive of positive change. Copyright © 2017 Elsevier Ltd. All rights reserved.

Preliminary Design of Compact Condenser in an Organic Rankine Cycle System for the Low Grade Waste Heat Recovery

Directory of Open Access Journals (Sweden)

Roberto Capata

2014-11-01

Full Text Available The aim of this paper is to present a thermodynamic cycle for the production of electrical power in the 2–5 kW range, suitable for all types of thermally propelled vehicles. The sensible heat recovered from the exhaust gases feeds the energy recovery system, which is able to produce sufficient power to sustain the air conditioning system or other auxiliaries. The working fluids R134a and R245fa have been used in the ORC system, and the systems are simulated by CAMEL-ProTM software. The cycles are generated starting from the same heat source: the exhaust gas of a typical 2.0 L Diesel engine (or from a small size turbine engine. The design of the condenser has been performed to obtain a very compact component, evaluating the heat exchanger tube and fins type design. Through empirical formulas, the area of heat exchange, the heat required to exchange and the pressure drop in the element have been calculated. A commercial software package is used to build the model of the condenser, then a thermal and mechanical analysis and a CFD analysis are realized to estimate the heat exchange. Finally the evaluations, the possible future studies and possible improvements of the system are shown.

Pharmacodynamic Comparison of Rocuronium Bromide between Patients from the Plateau Area and from the Plain Area.

Science.gov (United States)

Xie, Min; Huang, Jianxin; Li, Peng; Ou, Zhiyan; Hou, Jing

2016-06-23

We aimed to conduct a pharmacodynamic comparison of rocuronium bromide between patients from the plateau area and from the plain area. A total of 104 patients who received laparoscopic cholecystectomy in Sichuan Provincial People's Hospital and Aba Autonomous Prefecture People's Hospital from October 2015 to December 2015 were included in this study. Among them, 46 patients were from the plateau area and 58 were from the plain area. Both groups received total intravenous anesthesia (TIVA) with a dose of 0.6mg/kg rocuronium bromide during induction. In the meantime, neuromuscular block was monitored using a train-of-four (TOF) stimulation mode. The onset time (time to achieve the lowest TOF value after the injection of rocuronium bromide), duration of maximal neuromuscular block (duration of lowest T1 value), time to 25% recovery, time to 75% recovery, recovery index (time from 25% recovery to 75% recovery), time to extubation, length of stay in Post Anesthesia Care Unit (PACU) and muscle strength upon PACU discharge were all recorded. The onset time, time to 25% recovery, time to 75% recovery and time to extubation were all significantly prolonged in patients from the plateau area after receiving one single dose of rocuronium bromide (P0.05). Compared to patients from the plain area, patients from the plateau area showed prolonged onset time of rocuronium bromide, reduced metabolic capabilities and longer duration of muscular relaxation. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Glaciotectonics in the Cold Lake area and implications for steam-assisted heavy-oil recovery

Energy Technology Data Exchange (ETDEWEB)

Andriashek, L.D.; Fenton, M.M. [Alberta Geological Survey, Calgary, AB (Canada); Freitas de, T.; Mann, G. [Imperial Oil of Canada, Calgary, AB (Canada)

1999-11-01

A study was conducted to show how the depositional history of the Alberta`s Cold Lake region can have an impact on the use of steam assisted heavy-oil recovery in the oil sands region. The bitumens are found mainly within the 50 m thick estuarine and fluvial sandstone of the Cretaceous Clearwater Formation of the Mannville Group, at a depth of approximately 450 m. The stratigraphic sequences within the Mannville Group were presented. It has been determined that glaciotectonics have played a major role in the depositional history of the area. It was also determined that a good understanding of the hydrostratigraphic complexity makes it possible to better manage local ground water resources and to effectively plan further groundwater withdrawal sites.

Rare isotope accelerator—conceptual design of target areas

Science.gov (United States)

Bollen, Georg; Baek, Inseok; Blideanu, Valentin; Lawton, Don; Mantica, Paul F.; Morrissey, David J.; Ronningen, Reginald M.; Sherrill, Bradley S.; Zeller, Albert; Beene, James R.; Burgess, Tom; Carter, Kenneth; Carrol, Adam; Conner, David; Gabriel, Tony; Mansur, Louis; Remec, Igor; Rennich, Mark; Stracener, Dan; Wendel, Mark; Ahle, Larry; Boles, Jason; Reyes, Susana; Stein, Werner; Heilbronn, Lawrence

2006-06-01

The planned rare isotope accelerator facility RIA in the US would become the most powerful radioactive beam facility in the world. RIA's driver accelerator will be a device capable of providing beams from protons to uranium at energies of at least 400 MeV per nucleon, with beam power up to 400 kW. Radioactive beam production relies on both the in-flight separation of fast beam fragments and on the ISOL technique. In both cases the high beam power poses major challenges for target technology and handling and on the design of the beam production areas. This paper will give a brief overview of RIA and discuss aspects of ongoing conceptual design work for the RIA target areas.

Rare isotope accelerator - conceptual design of target areas

International Nuclear Information System (INIS)

Bollen, Georg; Baek, Inseok; Blideanu, Valentin; Lawton, Don; Mantica, Paul F.; Morrissey, David J.; Ronningen, Reginald M.; Sherrill, Bradley S.; Zeller, Albert; Beene, James R; Burgess, Tom; Carter, Kenneth; Carrol, Adam; Conner, David; Gabriel, Tony A; Mansur, Louis K; Remec, Igor; Rennich, Mark J; Stracener, Daniel W; Wendel, Mark W; Ahle, Larry; Boles, Jason; Reyes, Susana; Stein, Werner; Heilbronn, Lawrence

2006-01-01

The planned rare isotope accelerator facility RIA in the US would become the most powerful radioactive beam facility in the world. RIA's driver accelerator will be a device capable of providing beams from protons to uranium at energies of at least 400MeV per nucleon, with beam power up to 400 kW. Radioactive beam production relies on both the in-flight separation of fast beam fragments and on the ISOL technique. In both cases the high beam power poses major challenges for target technology and handling and on the design of the beam production areas. This paper will give a brief overview of RIA and discuss aspects of ongoing conceptual design work for the RIA target areas

36 CFR 212.57 - Monitoring of effects of motor vehicle use on designated roads and trails and in designated areas.

Science.gov (United States)

2010-07-01

... motor vehicle use on designated roads and trails and in designated areas. 212.57 Section 212.57 Parks... Roads, Trails, and Areas for Motor Vehicle Use § 212.57 Monitoring of effects of motor vehicle use on designated roads and trails and in designated areas. For each administrative unit of the National Forest...

Beam-dynamics driven design of the LHeC energy-recovery linac

Directory of Open Access Journals (Sweden)

Dario Pellegrini

2015-12-01

Full Text Available The LHeC is envisioned as a natural upgrade of the LHC that aims at delivering an electron beam for collisions with the existing hadronic beams. The current baseline design for the electron facility consists of a multipass superconducting energy-recovery linac (ERL operating in a continuous wave mode. The unprecedently high energy of the multipass ERL combined with a stringent emittance dilution budget poses new challenges for the beam optics. Here, we investigate the performances of a novel arc architecture based on a flexible momentum compaction lattice that mitigates the effects of synchrotron radiation while containing the bunch lengthening. Extensive beam-dynamics investigations have been performed with placet2, a recently developed tracking code for recirculating machines. They include the first end-to-end tracking and a simulation of the machine operation with a continuous beam. This paper briefly describes the Conceptual Design Report lattice, with an emphasis on possible and proposed improvements that emerged from the beam-dynamics studies. The detector bypass section has been integrated in the lattice, and its design choices are presented here. The stable operation of the ERL with a current up to ∼150  mA in the linacs has been validated in the presence of single- and multibunch wakefields, synchrotron radiation, and beam-beam effects.

Designing Mission Operations for the Gravity Recovery and Interior Laboratory Mission

Science.gov (United States)

Havens, Glen G.; Beerer, Joseph G.

2012-01-01

NASA's Gravity Recovery and Interior Laboratory (GRAIL) mission, to understand the internal structure and thermal evolution of the Moon, offered unique challenges to mission operations. From launch through end of mission, the twin GRAIL orbiters had to be operated in parallel. The journey to the Moon and into the low science orbit involved numerous maneuvers, planned on tight timelines, to ultimately place the orbiters into the required formation-flying configuration necessary. The baseline GRAIL mission is short, only 9 months in duration, but progressed quickly through seven very unique mission phases. Compressed into this short mission timeline, operations activities and maneuvers for both orbiters had to be planned and coordinated carefully. To prepare for these challenges, development of the GRAIL Mission Operations System began in 2008. Based on high heritage multi-mission operations developed by NASA's Jet Propulsion Laboratory and Lockheed Martin, the GRAIL mission operations system was adapted to meet the unique challenges posed by the GRAIL mission design. This paper describes GRAIL's system engineering development process for defining GRAIL's operations scenarios and generating requirements, tracing the evolution from operations concept through final design, implementation, and validation.

Consumer preferences in the design of airport passenger areas

NARCIS (Netherlands)

Van Oel, C.J.; Van den Berkhof, F.W.

2013-01-01

In recent decades, commercial developments have become increasingly important for the overall profit of airports. However, little is known about consumer preferences regarding the design of passenger areas, which is striking as the design of terminal buildings affects consumers' emotional state and

76 FR 37059 - Siuslaw National Forest; Oregon; Oregon Dunes NRA Management Area 10 (C) Route and Area Designation

Science.gov (United States)

2011-06-24

... DEPARTMENT OF AGRICULTURE Forest Service Siuslaw National Forest; Oregon; Oregon Dunes NRA Management Area 10 (C) Route and Area Designation AGENCY: Forest Service, USDA. ACTION: Notice of intent to... (C) today are not designated routes. This has in turn led to greater and unnecessary impacts to...

Rare Isotope Accelerator - Conceptual Design of Target Areas

Energy Technology Data Exchange (ETDEWEB)

Bollen, Georg [Michigan State University, East Lansing; Baek, Inseok [Michigan State University, East Lansing; Blideanu, Valentin [CEA, Saclay, France; Lawton, Don [Michigan State University, East Lansing; Mantica, Paul F. [Michigan State University, East Lansing; Morrissey, David J. [Michigan State University, East Lansing; Ronningen, Reginald M. [Michigan State University, East Lansing; Sherrill, Bradley S. [Michigan State University, East Lansing; Zeller, Albert [Michigan State University, East Lansing; Beene, James R [ORNL; Burgess, Tom [Oak Ridge National Laboratory (ORNL); Carter, Kenneth [Oak Ridge National Laboratory (ORNL); Carrol, Adam [Oak Ridge National Laboratory (ORNL); Conner, David [ORNL; Gabriel, Tony A [ORNL; Mansur, Louis K [ORNL; Remec, Igor [ORNL; Rennich, Mark J [ORNL; Stracener, Daniel W [ORNL; Wendel, Mark W [ORNL; Ahle, Larry [Lawrence Livermore National Laboratory (LLNL); Boles, Jason [Lawrence Livermore National Laboratory (LLNL); Reyes, Susana [Lawrence Livermore National Laboratory (LLNL); Stein, Werner [Lawrence Livermore National Laboratory (LLNL); Heilbronn, Lawrence [Lawrence Berkeley National Laboratory (LBNL)

2006-01-01

The planned rare isotope accelerator facility RIA in the US would become the most powerful radioactive beam facility in the world. RIA s driver accelerator will be a device capable of providing beams from protons to uranium at energies of at least 400MeV per nucleon, with beam power up to 400 kW. Radioactive beam production relies on both the in-flight separation of fast beam fragments and on the ISOL technique. In both cases the high beam power poses major challenges for target technology and handling and on the design of the beam production areas. This paper will give a brief overview of RIA and discuss aspects of ongoing conceptual design work for the RIA target areas.

Rare isotope accelerator-conceptual design of target areas

Energy Technology Data Exchange (ETDEWEB)

Bollen, Georg [National Superconducting Cyclotron Laboratory, Michigan State University, East Lansing, MI 48824 (United States)]. E-mail: bollen@nscl.msu.edu; Baek, Inseok; Blideanu, Valentin; Lawton, Don; Mantica, Paul F.; Morrissey, David J.; Ronningen, Reginald M.; Sherrill, Bradley S.; Zeller, Albert [National Superconducting Cyclotron Laboratory, Michigan State University, East Lansing, MI 48824 (United States); Beene, James R.; Burgess, Tom; Carter, Kenneth; Carrol, Adam; Conner, David; Gabriel, Tony; Mansur, Louis; Remec, Igor; Rennich, Mark; Stracener, Dan; Wendel, Mark [Oak Ridge National Laboratory, Oak Ridge, TN 37830 (United States); Ahle, Larry; Boles, Jason; Reyes, Susana; Stein, Werner [Lawrence Livermore Laboratory, Livermore, CA 94550 (United States); Heilbronn, Lawrence [Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States)

2006-06-23

The planned rare isotope accelerator facility RIA in the US would become the most powerful radioactive beam facility in the world. RIA's driver accelerator will be a device capable of providing beams from protons to uranium at energies of at least 400 MeV per nucleon, with beam power up to 400 kW. Radioactive beam production relies on both the in-flight separation of fast beam fragments and on the ISOL technique. In both cases the high beam power poses major challenges for target technology and handling and on the design of the beam production areas. This paper will give a brief overview of RIA and discuss aspects of ongoing conceptual design work for the RIA target areas.

Application and design of an economizer for waste heat recovery in a cogeneration plant

Directory of Open Access Journals (Sweden)

Martić Igor I.

2016-01-01

Full Text Available Energy increase cost has required its more effective use. However, many industrial heating processes generate waste energy. Use of waste-heat recovery systems decreases energy consumption. This paper presents case study of waste heat recovering of the exhaust flue gas in a 1415 kWe cogeneration plant. This waste heat can be recovered by installing an economizer to heat the condensed and fresh water in thermal degasification unit and reduce steam use for maintaining the temperature of 105˚C for oxygen removal. Design methodology of economizer is presented.

Perspective: Ecological recovery following the Exxon Valdez oil spill

International Nuclear Information System (INIS)

Maki, A.W.

1993-01-01

A series of field and laboratory studies were designed to characterize the initial effects and subsequent rate of ecosystem recovery following the Exxon Valdez oil spill. These studies were organized within an ecological risk assessment framework wherein measurements of residual spill hydrocarbons from specific environmental compartments were correlated with observed biological effects for resident species and communities. This allowed an assessment of the likelihood of spill-related effects vs. effects of natural ecosystem variability. Measurement of polycyclic automatic hydrocarbons (PAH) were made from throughout the spill-affected area for water column, intertidal shoreline sediments and deep subtidal sediments. Data document the expected high levels of PAH in 1989 with rapid PAH decreases in following years from all compartments reflecting natural assimilation and dissipation via chemical, physical and biological processes. Parallel investigations of risks to biological resources representing major trophic levels were conducted to quantify recovery rates of spill impacted habitats and resident species. Results are summarized documenting respective recovery rates for key trophic levels including intertidal flora and fauna, benthic invertebrates and infauna, herring and salmon, shorebirds and colonial seabirds and sea otters. Quantitative data developed for these species support the conclusion that the effects of oil spills are largely short-term acute events, and the Prince William Sound recovery was well advanced by 1991

A recovery journey for people with personality disorder.

Science.gov (United States)

Castillo, Heather; Ramon, Shulamit; Morant, Nicola

2013-05-01

The study investigates the process of recovery for people diagnosed with personality disorder, a client group that suffers significant social exclusion known to impact on demand for health and other public services. It aims to examine efforts that attempt to reverse this social exclusion as an aspect of the recovery process. and The following study aims to (1) explore what recovery means to people with personality disorder; (2) develop a conceptual model of recovery in personality disorder; and (3) evaluate the contribution of the setting (The Haven) to recovery practice. The study uses a Participatory Action Research (PAR) design. Data was collected from 66 participants by focus groups and individual interviews. A map based on thematic analysis of data collected during the study is proposed of the recovery journey for people with this diagnosis, shown as a pyramid that represents a hierarchy of progress, from building trust through stages of recovery to social inclusion. The findings offer contributions to knowledge in terms of the service design and propose a new model of recovery in personality disorder. This is defined as a journey of small steps highlighting recovery as a process rather than a goal, leading to the emergence of the new concept of transitional recovery.

A novel process for recovery of fermentation-derived succinic acid: process design and economic analysis.

Science.gov (United States)

Orjuela, Alvaro; Orjuela, Andrea; Lira, Carl T; Miller, Dennis J

2013-07-01

Recovery and purification of organic acids produced in fermentation constitutes a significant fraction of total production cost. In this paper, the design and economic analysis of a process to recover succinic acid (SA) via dissolution and acidification of succinate salts in ethanol, followed by reactive distillation to form succinate esters, is presented. Process simulation was performed for a range of plant capacities (13-55 million kg/yr SA) and SA fermentation titers (50-100 kg/m(3)). Economics were evaluated for a recovery system installed within an existing fermentation facility producing succinate salts at a cost of $0.66/kg SA. For a SA processing capacity of 54.9 million kg/yr and a titer of 100 kg/m(3) SA, the model predicts a capital investment of $75 million and a net processing cost of $1.85 per kg SA. Required selling price of diethyl succinate for a 30% annual return on investment is $1.57 per kg. Copyright © 2013 Elsevier Ltd. All rights reserved.

Identification of potential recovery facilities for designing a reverse supply chain network using physical programming

Science.gov (United States)

Pochampally, Kishore K.; Gupta, Surendra M.; Kamarthi, Sagar V.

2004-02-01

Although there are many quantitative models in the literature to design a reverse supply chain, every model assumes that all the recovery facilities that are engaged in the supply chain have enough potential to efficiently re-process the incoming used products. Motivated by the risk of re-processing used products in facilities of insufficient potentiality, this paper proposes a method to identify potential facilities in a set of candidate recovery facilities operating in a region where a reverse supply chain is to be established. In this paper, the problem is solved using a newly developed method called physical programming. The most significant advantage of using physical programming is that it allows a decision maker to express his preferences for values of criteria (for comparing the alternatives), not in the traditional form of weights but in terms of ranges of different degrees of desirability, such as ideal range, desirable range, highly desirable range, undesirable range, and unacceptable range. A numerical example is considered to illustrate the proposed method.

GRA prospectus: optimizing design and management of protected areas

Science.gov (United States)

Bernknopf, Richard; Halsing, David

2001-01-01

Protected areas comprise one major type of global conservation effort that has been in the form of parks, easements, or conservation concessions. Though protected areas are increasing in number and size throughout tropical ecosystems, there is no systematic method for optimally targeting specific local areas for protection, designing the protected area, and monitoring it, or for guiding follow-up actions to manage it or its surroundings over the long run. Without such a system, conservation projects often cost more than necessary and/or risk protecting ecosystems and biodiversity less efficiently than desired. Correcting these failures requires tools and strategies for improving the placement, design, and long-term management of protected areas. The objective of this project is to develop a set of spatially based analytical tools to improve the selection, design, and management of protected areas. In this project, several conservation concessions will be compared using an economic optimization technique. The forest land use portfolio model is an integrated assessment that measures investment in different land uses in a forest. The case studies of individual tropical ecosystems are developed as forest (land) use and preservation portfolios in a geographic information system (GIS). Conservation concessions involve a private organization purchasing development and resource access rights in a certain area and retiring them. Forests are put into conservation, and those people who would otherwise have benefited from extracting resources or selling the right to do so are compensated. Concessions are legal agreements wherein the exact amount and nature of the compensation result from a negotiated agreement between an agent of the conservation community and the local community. Funds are placed in a trust fund, and annual payments are made to local communities and regional/national governments. The payments are made pending third-party verification that the forest expanse

Evaluation of effects of phenol recovery on biooxidation and tertiary treatment of SRC-I wastewater. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Mitchell, J.W.; Watt, J.C.; Cowan, W.F.; Schuyler, S.E.

1983-09-01

Addition of phenol recovery to the wastewater treatment scheme in the Baseline Design for the SRC-I Demonstration Plant was evaluated as a major post-Baseline effort. Phenol recovery affects many downstream processes, but this study was designed to assess primarily its effects on biooxidation and subsequent tertiary treatment. Two parallel treatment schemes were set up, one to treat dephenolated wastewaters and the other for processed nondephenolated wastewaters, a simulation of the Baseline Design. The study focused on comparisons of five areas: effluent quality; system stability; the need for continuous, high-dose powdered activated carbon (PAC) augmentation to the bioreactor; minimum bioreactor hydraulic residence time (HRT); and tertiary treatment requirements. The results show that phenol recovery improves the quality of the bioreactor effluent in terms of residual organics and color. With phenol recovery, PAC augmentation is not required; without phenol recovery, PAC is needed to produce a comparable effluent. Dephenolization also enhances the stability of biooxidation, and reduces the minimum HRT required. With tertiary treatment, both schemes can meet the effluent concentrations published in the SRC-I Final Envivornmental Impact Statement, as well as the anticipated effluent limits. However, phenol recovery does provide a wider safety margin and could eliminate the need for some of the tertiary treatment steps. Based solely on the technical merits observed in this study, phenol recovery is recommended. The final selection should, however, also consider economic tradeoffs and results of other studies such as toxicology testing of the effluents. 34 references, 30 figures and 26 tables.

Study on incineration technology of oil gas generated during the recovery process of oil spill

International Nuclear Information System (INIS)

Hou, Shuhn-Shyurng; Ko, Yung-Chang; Lin, Ta-Hui

2011-01-01

The objective of this study is to design, set up and operate an incinerator system capable of providing clean exhaust and safety control for burning oil gas generated during the recovery process of oil spill in Taiwan. In this study, we successfully develop a vertical-type incinerator, which consists of five oil gas burners with entrained primary air, a pilot burner, and an auxiliary burner. The incinerator system is equipped with necessary control units in order to achieve safe, easy, fast, and efficient operation. Flame appearance, flue gas temperature and CO emission of the incinerator system for burning oil gas are reported and discussed. Under the long-term operation, it is found that the new designed incinerator is satisfactory for burning oil gas with low supply pressure at various compositions and supply rates during the recovery process of oil spill. It is noteworthy that the results obtained herein are of great significance to provide a good guidance for those who need to design, set up and operate an incinerator system providing clean exhaust and safety control for burning oil gas generated during the recovery process of oil spill in a polluted site with a large area.

Study on incineration technology of oil gas generated during the recovery process of oil spill

Energy Technology Data Exchange (ETDEWEB)

Hou, Shuhn-Shyurng [Department of Mechanical Engineering, Kun Shan University, Tainan 71003 (China); Ko, Yung-Chang [China Steel Corporation, Kaohsiung 81233 (China); Lin, Ta-Hui [Department of Mechanical Engineering, National Cheng Kung University, Tainan 70101 (China)

2011-03-15

The objective of this study is to design, set up and operate an incinerator system capable of providing clean exhaust and safety control for burning oil gas generated during the recovery process of oil spill in Taiwan. In this study, we successfully develop a vertical-type incinerator, which consists of five oil gas burners with entrained primary air, a pilot burner, and an auxiliary burner. The incinerator system is equipped with necessary control units in order to achieve safe, easy, fast, and efficient operation. Flame appearance, flue gas temperature and CO emission of the incinerator system for burning oil gas are reported and discussed. Under the long-term operation, it is found that the new designed incinerator is satisfactory for burning oil gas with low supply pressure at various compositions and supply rates during the recovery process of oil spill. It is noteworthy that the results obtained herein are of great significance to provide a good guidance for those who need to design, set up and operate an incinerator system providing clean exhaust and safety control for burning oil gas generated during the recovery process of oil spill in a polluted site with a large area. (author)

Design and numerical investigation of swirl recovery vanes for the Fokker 29 propeller

Directory of Open Access Journals (Sweden)

Wang Yangang

2014-10-01

Full Text Available Swirl recovery vanes (SRVs are a set of stationary vanes located downstream from a propeller, which may recover some of the residual swirl from the propeller, hoping for an improvement in both thrust and efficiency. The SRV concept design for a scaled version representing the Fokker 29 propeller is performed in this paper, which may give rise to a promotion in propulsive performance of this traditional propeller. Firstly the numerical strategy is validated from two aspects of global quantities and the local flow field of the propeller compared with experimental data, and then the exit flow together with the development of propeller wake is analyzed in detail. Three kinds of SRV are designed with multiple circular airfoils. The numerical results show that the swirl behind the propeller is recovered significantly with Model V3, which is characterized by the highest solidity along spanwise, for various working conditions, and the combination of rotor and vane produced 5.76% extra thrust at the design point. However, a lower efficiency is observed asking for a better vane design and the choice of a working point. The vane position is studied which shows that there is an optimum range for higher thrust and efficiency.

Recovery of a temperate reef assemblage in a marine protected area following the exclusion of towed demersal fishing.

Directory of Open Access Journals (Sweden)

Emma V Sheehan

Full Text Available Marine Protected Areas MPA have been widely used over the last 2 decades to address human impacts on marine habitats within an ecosystem management context. Few studies have quantified recovery of temperate rocky reef communities following the cessation of scallop dredging or demersal trawling. This is critical information for the future management of these habitats to contribute towards conservation and fisheries targets. The Lyme Bay MPA, in south west UK, has excluded towed demersal fishing gear from 206 km(2 of sensitive reef habitat using a Statutory Instrument since July 2008. To assess benthic recovery in this MPA we used a flying video array to survey macro epi-benthos annually from 2008 to 2011. 4 treatments (the New Closure, previously voluntarily Closed Controls and Near or Far Open to fishing Controls were sampled to test a recovery hypothesis that was defined as 'the New Closure becoming more similar to the Closed Controls and less similar to the Open Controls'. Following the cessation of towed demersal fishing, within three years positive responses were observed for species richness, total abundance, assemblage composition and seven of 13 indicator taxa. Definitive evidence of recovery was noted for species richness and three of the indicator taxa (Pentapora fascialis, Phallusia mammillata and Pecten maximus. While it is hoped that MPAs, which exclude anthropogenic disturbance, will allow functional restoration of goods and services provided by benthic communities, it is an unknown for temperate reef systems. Establishing the likely timescales for restoration is key to future marine management. We demonstrate the early stages of successful recruitment and link these to the potential wider ecosystem benefits including those to commercial fisheries.

Recovery of a temperate reef assemblage in a marine protected area following the exclusion of towed demersal fishing.

Science.gov (United States)

Sheehan, Emma V; Stevens, Timothy F; Gall, Sarah C; Cousens, Sophie L; Attrill, Martin J

2013-01-01

Marine Protected Areas MPA have been widely used over the last 2 decades to address human impacts on marine habitats within an ecosystem management context. Few studies have quantified recovery of temperate rocky reef communities following the cessation of scallop dredging or demersal trawling. This is critical information for the future management of these habitats to contribute towards conservation and fisheries targets. The Lyme Bay MPA, in south west UK, has excluded towed demersal fishing gear from 206 km(2) of sensitive reef habitat using a Statutory Instrument since July 2008. To assess benthic recovery in this MPA we used a flying video array to survey macro epi-benthos annually from 2008 to 2011. 4 treatments (the New Closure, previously voluntarily Closed Controls and Near or Far Open to fishing Controls) were sampled to test a recovery hypothesis that was defined as 'the New Closure becoming more similar to the Closed Controls and less similar to the Open Controls'. Following the cessation of towed demersal fishing, within three years positive responses were observed for species richness, total abundance, assemblage composition and seven of 13 indicator taxa. Definitive evidence of recovery was noted for species richness and three of the indicator taxa (Pentapora fascialis, Phallusia mammillata and Pecten maximus). While it is hoped that MPAs, which exclude anthropogenic disturbance, will allow functional restoration of goods and services provided by benthic communities, it is an unknown for temperate reef systems. Establishing the likely timescales for restoration is key to future marine management. We demonstrate the early stages of successful recruitment and link these to the potential wider ecosystem benefits including those to commercial fisheries.

Literature Review on Disruption Recovery in the Supply Chain

OpenAIRE

Ivanov , Dmitry; Dolgui , Alexandre; Sokolov , Boris; Ivanova , Marina

2017-01-01

International audience; Recent research underlines the crucial role of disruption events and recovery policies in supply chains. Despite a wealth of literature on supply chain design with disruption considerations, to the best of our knowledge there is no survey on supply chain with disruptions and recovery considerations. We analyse state-of-the-art research streams on supply chain design and planning with both disruptions and recovery considerations with the aim of relating the existing qua...

Request for modification of 200 Area effluent treatment facility final delisting

International Nuclear Information System (INIS)

Bowman, R.C.

1998-01-01

A Delisting Petition submitted to the U.S. Environmental Protection Agency in August 1993 addressed effluent to be generated at the 200 Area Effluent Treatment Facility from treating Hanford Facility waste streams. This Delisting Petition requested that 71.9 million liters per year of treated effluent, bearing the designation 'F001' through 'F005', and/or 'F039' that is derived from 'F001' through 'F005' waste, be delisted. On June 13, 1995, the U.S. Environmental Protection Agency published the final rule (Final Delisting), which formally excluded 71.9 million liters per year of 200 Area Effluent Treatment Facility effluent from ''being listed as hazardous wastes'' (60 FR 31115 now promulgated in 40 CFR 261). Given the limited scope, it is necessary to request a modification of the Final Delisting to address the management of a more diverse multi-source leachate (F039) at the 200 Area Effluent Treatment Facility. From past operations and current cleanup activities on the Hanford Facility, a considerable amount of both liquid and solid Resource Conservation and Recovery Act of 1976 regulated mixed waste has been and continues to be generated. Ultimately this waste will be treated as necessary to meet the Resource Conservation and Recovery Act Land Disposal Restrictions. The disposal of this waste will be in Resource Conservation and Recovery Act--compliant permitted lined trenches equipped with leachate collection systems. These operations will result in the generation of what is referred to as multi-source leachate. This newly generated waste will receive the listed waste designation of F039. This waste also must be managed in compliance with the provisions of the Resource Conservation and Recovery Act

The importance of high-level predators in marine protected area management: Consequences of their decline and their potential recovery in the Mediterranean context

Directory of Open Access Journals (Sweden)

Giulia Prato

2013-11-01

Full Text Available High-level predators have been depleted in the oceans worldwide following centuries of selective fishing. There is widespread evidence that high-level predators’ extirpation may trigger trophic cascades leading to the degradation of marine ecosystems. Restoration of large carnivores to former levels of abundance might lead to ecosystem recovery, but very few pristine ecosystems are left as baselines for comparison. Marine protected areas (MPAs can trigger initial rapid increases of high-level predator abundance and biomass. Nevertheless, long term protection is needed before the ecosystem's carrying capacity for large carnivores is approached and indirect effects on lower trophic levels are observed. The Mediterranean is probably very far from its pristine condition, due to a long history of fishing. Today small to medium-sized consumers (e.g. sea breams are the most abundant predators shaping coastal benthic communities, while historical reconstructions depict abundant populations of large piscivores and sharks inhabiting coastal areas. Mediterranean MPAs are following a promising trajectory of ecosystem recovery, as suggested by a strong gradient of fish biomass increase. Consistent monitoring methods to assess relative variations of high-level predators, together with food-web models aimed at disentangling the indirect effects of their recovery, could be useful tools to help set up appropriate management strategies of MPAs.

Design, fabrication and testing of the gas analysis system for the tritium recovery experiment, TRIO-01

International Nuclear Information System (INIS)

Finn, P.A.; Reedy, G.T.; Homa, M.I.; Clemmer, R.G.; Pappas, G.; Slawecki, M.A.; Graczyk, D.G.; Bowers, D.L.; Clemmer, E.D.

1983-01-01

The tritium recovery experiment, TRIO-01, required a gas analysis system which detected the form of tritium, the amount of tritium (differential and integral), and the presence and amount of other radioactive species. The system had to handle all contingencies and function for months at a time unattended during weekend operation. The designed system, described herein, consisted of a train of components which could be grouped as desired to match tritium release behavior

Biological opportunities for metal recovery

International Nuclear Information System (INIS)

Holmes, D.S.; Debus, S.H.

1991-01-01

An overview is presented of existing biological technologies for the recovery of copper and uranium. Engineering and biological challenges and opportunities in these areas are discussed. New opportunities for the bio oxidation of refractory goal ore are described. Techniques for the development of new strains of microorganisms for commercial metal recovery applications are discussed with special reference to the use of genetic manipulation for bacterial strain improvement. (author)

Waste heat recovery system

International Nuclear Information System (INIS)

Phi Wah Tooi

2010-01-01

Full text: The Konzen in-house designed anaerobic digester system for the POME (Palm Oil Mill Effluent) treatment process is one of the registered Clean Development Mechanism (CDM) projects in Malaysia. It is an organic wastewater treatment process which achieves excellent co-benefits objectives through the prevention of water pollution and reduction of greenhouse gas emissions, which is estimated to be 40,000 to 50,000 t-CO 2 per year. The anaerobic digester was designed in mesophile mode with temperature ranging from 37 degree Celsius to 45 degree Celsius. A microorganisms growth is optimum under moderately warm temperature conditions. The operating temperature of the anaerobic digester needs to be maintained constantly. There are two waste heat recovery systems designed to make the treatment process self-sustaining. The heat recovered will be utilised as a clean energy source to heat up the anaerobic digester indirectly. The first design for the waste heat recovery system utilises heat generated from the flue gas of the biogas flaring system. A stainless steel water tank with an internal water layer is installed at the top level of the flare stack. The circulating water is heated by the methane enriched biogas combustion process. The second design utilizes heat generated during the compression process for the biogas compressor operation. The compressed biogas needs to be cooled before being recycled back into the digester tank for mixing purposes. Both the waste heat recovery systems use a design which applies a common water circulation loop and hot water tank to effectively become a closed loop. The hot water tank will perform both storage and temperature buffer functions. The hot water is then used to heat up recycled sludge from 30 degree Celsius to 45 degree Celsius with the maximum temperature setting at 50 degree Celsius. The recycled sludge line temperature will be measured and monitored by a temperature sensor and transmitter, which will activate the

A conceptional design, cost and sensitivity analysis on adsorption process for uranium recovery from seawater

International Nuclear Information System (INIS)

Ogata, Noboru

1986-01-01

The system model for a conceptional design and cost estimation was studied on a multi-layered fluidizing bed with a pump which used hydrous titanium oxide (HTO) and amidoxime resin (AOR) as adsorbents. The cost effect of some parameters, namely characteristics of adsorbent, operating conditions, price of materials and some others, were estimated, and finally there was shown a direction of improvement and a possibility of cost reduction. The conceptional design and operating condition were obtained from the balance point on expansion ratio, recovery and characteristics of adsorbent. A suitable plan was obtained from the minimum cost condition in some level of the expansion ratio and some parameters. HTO was heavy in density and cheap in price. The main results of the study indicated that the thickness of the bed was 1 m, the linear velocity of seawater was 52 m/hr, the number of bed layers was 4, the construction cost of a 100 t/y plant was 10 billion yen, and the uranium cost was 160 $/1b. AOR had a large adsorption capacity. As the main results, the thickness of bed was 0.08 m, the linear velosity of seawater was 11.6 m, the number of the bed layers was 27, the construction cost of a 100 t/y plant was 15 billion yen, and the uranium cost was 280 $/1b. The size of the 100 t/y plant was about 800 m length x 80 m depth x 30 m height at 80 % of recovery. An increase of adsorption capacity in HTO, and an increase of density and particle size in AOR had the greatest merit for cost reduction. Other effective parameters were the adsorption velocity, the recovery, temperature, the price of adsorbent, the manufacturing cost of instrument, and the rate of interest. The cost of uranium by this process had a possibility of cost reduction to 67 $/1b at HTO and 79 $/1b at AOR. (author)

An Internal Standard for Assessing Phosphopeptide Recovery from Metal Ion/Oxide Enrichment Strategies

Science.gov (United States)

Paulo, Joao A.; Navarrete-Perea, Jose; Erickson, Alison R.; Knott, Jeffrey; Gygi, Steven P.

2018-04-01

Phosphorylation-mediated signaling pathways have major implications in cellular regulation and disease. However, proteins with roles in these pathways are frequently less abundant and phosphorylation is often sub-stoichiometric. As such, the efficient enrichment, and subsequent recovery of phosphorylated peptides, is vital. Mass spectrometry-based proteomics is a well-established approach for quantifying thousands of phosphorylation events in a single experiment. We designed a peptide internal standard-based assay directed toward sample preparation strategies for mass spectrometry analysis to understand better phosphopeptide recovery from enrichment strategies. We coupled mass-differential tandem mass tag (mTMT) reagents (specifically, TMTzero and TMTsuper-heavy), nine mass spectrometry-amenable phosphopeptides (phos9), and peak area measurements from extracted ion chromatograms to determine phosphopeptide recovery. We showcase this mTMT/phos9 recovery assay by evaluating three phosphopeptide enrichment workflows. Our assay provides data on the recovery of phosphopeptides, which complement other metrics, namely the number of identified phosphopeptides and enrichment specificity. Our mTMT/phos9 assay is applicable to any enrichment protocol in a typical experimental workflow irrespective of sample origin or labeling strategy. [Figure not available: see fulltext.

Design criteria document, electrical system, K-Basin essential systems recovery, Project W-405

International Nuclear Information System (INIS)

Hoyle, J.R.

1994-01-01

This Design Criteria Document provides the criteria for design and construction of electrical system modifications for 100K Area that are essential to protect the safe operation and storage of spent nuclear fuel in the K-Basin facilities

The development of the Be Active & Relax "Vitality in Practice" (VIP) project and design of an RCT to reduce the need for recovery in office employees

NARCIS (Netherlands)

Coffeng, J.K.; Hendriksen, I.J.M.; Duijts, S.F.A.; Proper, K.I.; van Mechelen, W.; Boot, C.R.L.

2012-01-01

Background: There is strong evidence to suggest that multiple work-related health problems are preceded by a higher need for recovery. Physical activity and relaxation are helpful in decreasing the need for recovery. This article aims to describe (1) the development and (2) the design of the

Design for behaviour change : Introducing five areas of application and related case studies

NARCIS (Netherlands)

Niedderer, Kristina; Clune, Stephen; Ludden, Geke; Niedderer, Kristina; Clune, Stephen; Ludden, Geke

2017-01-01

Part 3 of this book explores the real-world application of design for behavioural change principles and tools within five thematic areas. These five areas are as follows: • Sustainability • Health and wellbeing • Safety • Design against crime • Social design.

Type 'A' and 'B' recovery revisited: The role of field-edge habitats for Collembola and macroarthropod community recovery after insecticide treatment

International Nuclear Information System (INIS)

Frampton, Geoff K.; Gould, Philip J.L.; Brink, Paul J. van den; Hendy, Eleanor

2007-01-01

Previous work has identified two patterns of arthropod recovery after insecticide applications to arable crops: dispersal-mediated recolonisation from untreated areas (Type A) and recolonisation within treated areas assisted by reduced predation (Type B). In this study, connectivity between field-edge habitats was manipulated using barriers to investigate whether a crop edge and adjacent hedgerow influence recolonisation of an insecticide-treated crop by surface-active Collembola and other arthropods. Collembola recovery patterns differed among closely-related taxa. Epigeic collembolan and macroarthropod communities were more diverse and abundant, and rates of artificial prey predation were higher, in sprayed crop areas connected to both hedgerow and unsprayed crop edge than in sprayed areas connected to the unsprayed edge alone. These findings indicate that effectiveness of unsprayed crop edges as sources of field recolonisation may depend on adjoining field margin habitats. An assumption in risk assessment that unsprayed crop edges assist population recovery within treated areas is not supported. - Collembola recolonisation differs among species; effectiveness of unsprayed crop edges as sources of arthropod recolonisation may depend on adjacent habitat

Measuring the Recovery Orientation of ACT

Science.gov (United States)

Salyers, Michelle P.; Stull, Laura G.; Rollins, Angela L.; McGrew, John H.; Hicks, Lia J.; Thomas, Dave; Strieter, Doug

2014-01-01

Background Approaches to measuring recovery orientation are needed, particularly for programs that may struggle with implementing recovery-oriented treatment. Objective A mixed methods comparative study was conducted to explore effective approaches to measuring recovery orientation of Assertive Community Treatment (ACT) teams. Design Two ACT teams exhibiting high and low recovery orientation were compared using surveys, treatment plan ratings, diaries of treatment visits, and team-leader-reported treatment control mechanisms. Results The recovery-oriented team differed on one survey measure (higher expectations for consumer recovery), treatment planning (greater consumer involvement and goal-directed content), and use of control mechanisms (less use of representative payee, agency-held lease, daily medication delivery, and family involvement). Staff and consumer diaries showed the most consistent differences (e.g., conveying hope and choice) and were the least susceptible to observer bias, but had the lowest response rates. Conclusions Several practices differentiate recovery orientation on ACT teams, and a mixed-methods assessment approach is feasible. PMID:23690285

Analysis and Design of Timing Recovery Schemes for DMT Systems over Indoor Power-Line Channels

Directory of Open Access Journals (Sweden)

Cortés José Antonio

2007-01-01

Full Text Available Discrete multitone (DMT modulation is a suitable technique to cope with main impairments of broadband indoor power-line channels: spectral selectivity and cyclic time variations. Due to the high-density constellations employed to achieve the required bit-rates, synchronization issues became an important concern in these scenarios. This paper analyzes the performance of a conventional DMT timing recovery scheme designed for linear time-invariant (LTI channels when employed over indoor power lines. The influence of the channel cyclic short-term variations and the sampling jitter on the system performance is assessed. Bit-rate degradation due to timing errors is evaluated in a set of measured channels. It is shown that this synchronization mechanism limits the system performance in many residential channels. Two improvements are proposed to avoid this end: a new phase error estimator that takes into account the short-term changes in the channel response, and the introduction of notch filters in the timing recovery loop. Simulations confirm that the new scheme eliminates the bit-rate loss in most situations.

Conceptual design report, 200 Area sanitary sewer system: Project 96L-EWL-116

International Nuclear Information System (INIS)

Pursley, D.L.

1994-01-01

Project L-116 will install an integrated sanitary sewer system in the 200 Area. This new system will connect existing sewer systems for facilities that have a foreseeable future, provide capacity and routing for future facilities, and install new septic sewer systems for existing facilities that cannot be feasibly connected to the new sewer system and have a mission that will extend beyond the year 2000. Project L-116 will construct a sanitary sewer collection, treatment, and disposal system for facilities in the 200-East and -West Areas and adjacent areas located on the 200 Area plateau. The existing septic systems will be abandoned or decommissioned in accordance with applicable Washington State and local codes and regulations. The conceptual design for the sanitary sewer system is designed around population forecasts of 5,000 people for 200-West Area and 9,000 people for 200-East Area. The definitive design will be based on the latest forecast populations at the time definitive design is initiated

Illness management and recovery (IMR) in Danish community mental health centres

DEFF Research Database (Denmark)

Dalum, Helle Stentoft; Korsbek, Lisa; Mikkelsen, John Hagel

2011-01-01

Background: Schizophrenia and bipolar disorder are severe mental illnesses that can have a significant disabling impact on the lives of people. Psychosocial interventions that stress hope and recovery as a part of a multidimensional approach are possibly indicated to support people with severe...... mental illness in facilitating recovery. Illness Management and Recovery (IMR) is a curriculum-based psychosocial intervention designed as structured program with a recovery-oriented approach. The aim of IMR is to rehabilitate people with severe mental illnesses by helping them acquire knowledge...... and skills in managing their illness and achieve personal recovery goals. Previous randomised clinical trials indicate that IMR can be implemented with a good effect and a high fidelity though further trials are crucial to demonstrate the potential effectiveness of IMR. Methods/Design: The trial design...

Robust Design of Docking Hoop for Recovery of Autonomous Underwater Vehicle with Experimental Results

Directory of Open Access Journals (Sweden)

Wei Peng Lin

2015-12-01

Full Text Available Control systems prototyping is usually constrained by model complexity, embedded system configurations, and interface testing. The proposed control system prototyping of a remotely-operated vehicle (ROV with a docking hoop (DH to recover an autonomous underwater vehicle (AUV named AUVDH using a combination of software tools allows the prototyping process to be unified. This process provides systematic design from mechanical, hydrodynamics, dynamics modelling, control system design, and simulation to testing in water. As shown in a three-dimensional simulation of an AUVDH model using MATLAB™/Simulink™ during the launch and recovery process, the control simulation of a sliding mode controller is able to control the positions and velocities under the external wave, current, and tether forces. In the water test using the proposed Python-based GUI platform, it shows that the AUVDH is capable to perform station-keeping under the external disturbances.

Development and fabrication of a high current, fast recovery power diode

Science.gov (United States)

Berman, A. H.; Balodis, V.; Devance, D. C.; Gaugh, C. E.; Karlsson, E. A.

1983-01-01

A high voltage (VR = 1200 V), high current (IF = 150 A), fast recovery ( 700 ns) and low forward voltage drop ( 1.5 V) silicon rectifier was designed and the process developed for its fabrication. For maximum purity, uniformity and material characteristic stability, neutron transmutation n-type doped float zone silicon is used. The design features a hexagonal chip for maximum area utilization of space available in the DO-8 diode package, PIN diffused junction structure with deep diffused D(+) anode and a shallow high concentration n(+) cathode. With the high temperature glass passivated positive bevel mesa junction termination, the achieved blocking voltage is close to the theoretical limit of the starting material. Gold diffusion is used to control the lifetime and the resulting effect on switching speed and forward voltage tradeoff. For solder reflow assembly, trimetal (Al-Ti-Ni) contacts are used. The required major device electrical characteristics were achieved. Due to the tradeoff nature of forward voltage drop and reverse recovery time, a compromise was reached for these values.

Request for modification of 200 Area effluent treatment facility final delisting

Energy Technology Data Exchange (ETDEWEB)

BOWMAN, R.C.

1998-11-19

A Delisting Petition submitted to the U.S. Environmental Protection Agency in August 1993 addressed effluent to be generated at the 200 Area Effluent Treatment Facility from treating Hanford Facility waste streams. This Delisting Petition requested that 71.9 million liters per year of treated effluent, bearing the designation 'F001' through 'F005', and/or 'F039' that is derived from 'F001' through 'F005' waste, be delisted. On June 13, 1995, the U.S. Environmental Protection Agency published the final rule (Final Delisting), which formally excluded 71.9 million liters per year of 200 Area Effluent Treatment Facility effluent from ''being listed as hazardous wastes'' (60 FR 31115 now promulgated in 40 CFR 261). Given the limited scope, it is necessary to request a modification of the Final Delisting to address the management of a more diverse multi-source leachate (F039) at the 200 Area Effluent Treatment Facility. From past operations and current cleanup activities on the Hanford Facility, a considerable amount of both liquid and solid Resource Conservation and Recovery Act of 1976 regulated mixed waste has been and continues to be generated. Ultimately this waste will be treated as necessary to meet the Resource Conservation and Recovery Act Land Disposal Restrictions. The disposal of this waste will be in Resource Conservation and Recovery Act--compliant permitted lined trenches equipped with leachate collection systems. These operations will result in the generation of what is referred to as multi-source leachate. This newly generated waste will receive the listed waste designation of F039. This waste also must be managed in compliance with the provisions of the Resource Conservation and Recovery Act.

Informing Healthcare Waiting Area Design Using Transparency Attributes: A Comparative Preference Study.

Science.gov (United States)

Jiang, Shan; Powers, Matthew; Allison, David; Vincent, Ellen

2017-07-01

This study aimed to explore people's visual preference for waiting areas in general hospital environments designed with transparency attributes that fully integrate nature. Waiting can be a tedious and frustrating experience among people seeking healthcare treatments and negatively affect their perception of the quality of care. Positive distractions and supportive designs have gained increasing attraction to improve people's waiting experience. Nature, which has shown therapeutic effects according to a growing amount of evidence, could be a distinguished positive distraction in waiting areas. Additionally, the theory of transparency was operationalized to indicate a spatial continuity between the external nature and the built interiors in general healthcare waiting area design. A survey method was adopted in the study. Twenty-one images of general healthcare waiting areas depicting three design typologies were preselected following a strict procedure, including designs with (a) no window views, (b) limited window views to nature, and (c) transparent spaces with maximum natural views. Ninety-five student participants rated the images based on their visual preference using a Likert-type scale. The results showed that transparent waiting areas were significantly preferred. A significant positive relationship existed between the level of transparency and people's preference scores. The factor analysis indicated additional supportive features that may affect people's preferences, including daylight, perceived warmth, noninstitutional furniture arrangement, visual orientation, and the use of natural materials for interior design. However, these tentative results need to be furthered tested with the real patient population as the next step of this study.

Evaluation and Preliminary Design of a Stormwater Aquifer Storage and Recovery (ASR) System at the Wadi Khulays Dunefield in Saudi Arabia

KAUST Repository

Lopez Valencia, Oliver M.

2013-04-01

An important source of freshwater in arid lands is found in groundwater aquifers that are recharged after storm events. However, most of the precipitation is lost due to evaporation and only small fractions actually recharge the aquifers. The construction of dams along wadi channels enables the retention of stormwater, however the reservoirs are still subject to huge evaporative losses and contamination. In this study, the hydraulic properties of a dunefield in western Saudi Arabia are evaluated in order to determine the feasibility of designing a stormwater storage aquifer storage and recovery facility using the dune sands as a natural medium and design recommendations are addressed. The accurate estimation of hydraulic conductivity of unlithified sediments such as dune sands has become very important in the design of natural filtration projects, including aquifer recharge and recovery systems. Therefore, a comparison and selection of methods for the determination of the hydraulic conductivity from grain size distribution found in the literature was done. An improvement to these equations based on measurements on dune samples was obtained.

Modelling post-fire vegetation recovery in Portugal

Science.gov (United States)

Bastos, A.; Gouveia, C. M.; Dacamara, C. C.; Trigo, R. M.

2011-12-01

Wildfires in Mediterranean Europe have been increasing in number and extension over the last decades and constitute one of the major disturbances of these ecosystems. Portugal is the country with more burnt area in the last decade and the years of 2003 and 2005 were particularly devastating, the total burned areas of 425 000 and 338 000 ha being several times higher than the corresponding average. The year of 2005 further coincided with one of the most severe droughts since early 20th century. Due to different responses of vegetation to diverse fire regimes and to the complexity of landscape structures, fires have complex effects on vegetation recovery. Remote sensing has revealed to be a powerful tool in studying vegetation dynamics and in monitoring post-fire vegetation recovery, which is crucial to land-management and to prevent erosion. The main goals of the present work are (i) to assess the accuracy of a vegetation recovery model previously developed by the authors; (ii) to assess the model's performance, namely its sensitivity to initial conditions, to the temporal length of the input dataset and to missing data; (iii) to study vegetation recovery over two selected areas that were affected by two large wildfire events in the fire seasons of 2003 and 2005, respectively. The study relies on monthly values of NDVI over 11 years (1998-2009), at 1 km × 1 km spatial resolution, as obtained by the VEGETATION instrument. According to results from sensitivity analysis, the model is robust and able to provide good estimations of recovery times of vegetation when the regeneration process is regular, even when missing data is present. In respect to the two selected burnt scars, results indicate that fire damage is a determinant factor of regeneration, as less damaged vegetation recovers more rapidly, which is mainly justified by the high coverage of Pinus pinaster over the area, and by the fact that coniferous forests tend to recover slower than transitional woodland

Development and validation of attitudes towards Recovery Questionnaire across Chinese people in recovery, their family carers, and service providers in Hong Kong.

Science.gov (United States)

Mak, Winnie W S; Chan, Randolph C H; Yau, Sania S W

2018-05-29

Considering the lack of existing measures on attitudes toward personal recovery and the need to acknowledge the cultural milieu in recovery attitude assessment, the present study developed and validated the Attitudes towards Recovery Questionnaire (ARQ) in a sample of people in recovery of mental illness, family carers, and mental health service providers in Hong Kong. The ARQ was developed based on existing literature and measures of recovery, and focus group discussions with various stakeholders. Findings of the multi-sample confirmatory factor analyses supported a five-factor structure: (1) resilience as a person in recovery, (2) self-appreciation and development, (3) self-direction, (4) family involvement, and (5) social ties and integration. The ARQ was positively correlated with recovery outcomes, empowerment, recovery knowledge, and recovery orientation of mental health services. As a tool for examining recovery attitudes, the ARQ informs us of the mindset across stakeholders and areas that need enhancement to facilitate the recovery process. Copyright © 2018. Published by Elsevier B.V.

Preconceptual design for the electrostatic enclosure

International Nuclear Information System (INIS)

Meyer, L.C.

1992-09-01

This report presents a preconceptual design (design criteria and assumptions) for electrostatic enclosures to be used during buried transuranic waste recovery operations. These electrostatic enclosures (along with the application of dust control products) will provide an in-depth contamination control strategy. As part of this preconceptual design, options for electrostatic curtain design are given including both hardwall and fabric enclosures. Ventilation systems, doors, air locks, electrostatic curtains, and supporting systems also are discussed. In addition to the conceptual design, engineering scale tests are proposed to be run at the Test Reactor Area. The planned engineering scale tests will give final material specifications for full-scale retrieval demonstrations

The design, fabrication and testing of the gas analysis system for the tritium recovery experiment, TRIO-01

International Nuclear Information System (INIS)

Finn, P.A.; Bowers, D.L.; Clemmer, E.D.; Clemmer, R.G.; Graczyk, D.G.; Homa, M.I.; Pappas, G.; Reedy, G.T.; Slawecki, M.A.

1983-01-01

The tritium recovery experiment, TRIO-01, required a gas analysis system which detected the form of tritium, the amount of tritium (differential and integral), and the presence and amount of other radioactive species. The system had to handle all contingencies and function for months at a time; unattended during weekend operation. The designed system, described herein, consisted of a train of components which could be grouped as desired to match tritium release behavior

Application of the GEM Inventory Data Capture Tools for Dynamic Vulnerability Assessment and Recovery Modelling

Science.gov (United States)

Verrucci, Enrica; Bevington, John; Vicini, Alessandro

2014-05-01

A set of open-source tools to create building exposure datasets for seismic risk assessment was developed from 2010-13 by the Inventory Data Capture Tools (IDCT) Risk Global Component of the Global Earthquake Model (GEM). The tools were designed to integrate data derived from remotely-sensed imagery, statistically-sampled in-situ field data of buildings to generate per-building and regional exposure data. A number of software tools were created to aid the development of these data, including mobile data capture tools for in-field structural assessment, and the Spatial Inventory Data Developer (SIDD) for creating "mapping schemes" - statistically-inferred distributions of building stock applied to areas of homogeneous urban land use. These tools were made publically available in January 2014. Exemplar implementations in Europe and Central Asia during the IDCT project highlighted several potential application areas beyond the original scope of the project. These are investigated here. We describe and demonstrate how the GEM-IDCT suite can be used extensively within the framework proposed by the EC-FP7 project SENSUM (Framework to integrate Space-based and in-situ sENSing for dynamic vUlnerability and recovery Monitoring). Specifically, applications in the areas of 1) dynamic vulnerability assessment (pre-event), and 2) recovery monitoring and evaluation (post-event) are discussed. Strategies for using the IDC Tools for these purposes are discussed. The results demonstrate the benefits of using advanced technology tools for data capture, especially in a systematic fashion using the taxonomic standards set by GEM. Originally designed for seismic risk assessment, it is clear the IDCT tools have relevance for multi-hazard risk assessment. When combined with a suitable sampling framework and applied to multi-temporal recovery monitoring, data generated from the tools can reveal spatio-temporal patterns in the quality of recovery activities and resilience trends can be

Coping and recovery in whiplash-associated disorders

DEFF Research Database (Denmark)

Carroll, Linda J; Ferrari, Robert; Cassidy, John David

2014-01-01

Management Inventory, and neck pain recovery was assessed at each subsequent follow-up, using a 100 mm visual analogue scale (VAS). Disability was assessed at each follow-up using the Pain Disability Index (PDI). Pain recovery was defined as a VAS score of 0 to 10; disability recovery was defined as a PDI...... recovery, reductions in neck pain, and in disability. METHODS: A population-based prospective cohort study design was used to study 2986 adults with traffic-related WAD. Participants were assessed at baseline, 6 weeks, and 4, 8, and 12 months postinjury. Coping was measured at 6 weeks using the Pain...... score of 0 to 4. Data analysis used multivariable Cox proportional hazards models. RESULTS: Those using high versus low levels of passive coping at 6 weeks postinjury experienced 28% slower pain recovery and 43% slower disability recovery. Adjusted hazard rate ratios for pain recovery and disability...

Cerebral circulation and metabolism with recovery of chronic poststroke aphasia

International Nuclear Information System (INIS)

Yamada, Tomoyuki; Kabasawa, Hidehiro; Matsubara, Michitaka; Hibino, Hiroaki; Kamimoto, Kaoru; Fukagawa, Kazutoshi

2004-01-01

The recruitment of cerebral circulation and oxygen metabolism in the particular brain areas responsible for poststroke aphasia are necessary for recovery. This study was undertaken to investigate changes in cerebral circulation and oxygen metabolism corresponding to improvement of aphasia. Twenty-nine right-handed chronic aphasic patients with left hemispheric stroke were studied. Aphasia was evaluated as the score of fluency, comprehension, repetition and naming by the Western Aphasia Battery (Japanese version). Concurrent with the evaluation of aphasia, positron emission tomography (PET) scans were performed. After several months of speech therapy, PET scans and evaluation of aphasia were reperformed. Both regional cerebral blood flow and the cerebral metabolic rate for oxygen significantly increased in the left upper superior and middle temporal gyri, and in the left upper inferior frontal gyrus in the fair recovery group for comprehension, repetition and naming. In the fair recovery group for fluency, the cerebral metabolic rate for oxygen significantly increased in the left upper superior and middle temporal gyri, but regional cerebral blood flow increased insignificantly in these areas. In the lower white matter of the right parietal lobe, both the regional cerebral blood flow and the cerebral metabolic rate for oxygen were significantly increased in the fair recovery group for all aphasic features. The recruitment of cerebral circulation and oxygen metabolism in the left temporo-parietal area, in the left inferior frontal area, and in the right deep parietal area are essentially responsible for the recovery of aphasia. (author)

LQG/LTR [linear quadratic Gaussian with loop transfer recovery] robust control system design for a low-pressure feedwater heater train

International Nuclear Information System (INIS)

Murphy, G.V.; Bailey, J.M.

1990-01-01

This paper uses the linear quadratic Gaussian with loop transfer recovery (LQG/LTR) control system design method to obtain a level control system for a low-pressure feedwater heater train. The control system performance and stability robustness are evaluated for a given set of system design specifications. The tools for analysis are the return ratio, return difference, and inverse return difference singular-valve plots for a loop break at the plant output. 3 refs., 7 figs., 2 tabs

Colour and lighting in hospital design

Science.gov (United States)

Dalke, Hilary; Little, Jenny; Niemann, Elga; Camgoz, Nilgun; Steadman, Guillaume; Hill, Sarah; Stott, Laura

2006-06-01

Little information or guidance has been available to assist the development of a hospital's visual environment. A report on lighting and colour design schemes, accessible to non professionals with responsibility for refurbishment strategies, was required by NHS Estates. Firstly, 20 hospitals were audited to establish a picture of current practice and to identify key issues where colour design could broadly enhance the environment for patients, staff and visitors. Critical areas were outlined in this report, where colour design can be utilised and applied, for the benefit of all users, from ambience to essential legal requirements such as colour contrast for the visually impaired. Provision of staff relaxation rooms that are different in terms of colour and lux levels from immediate work spaces, or thoughtfully designed areas for patients awaiting intensive treatment, have been shown to have some beneficial effects on a sense of well being. Colour and design have not been established as a definite cure for sickness and ill health, but certainly monotony and poor conditions in premises that have not been refurbished with any care, have had a detrimental affect on recovery rates and staff morale. The realisation that a well balanced and attractive environment is of major importance to patients' health is, in no way new; Florence Nightingale observed that 'a variety of form and brilliance of colour in the objects presented to patients are an actual means of recovery'.

Performance analysis of diesel engine heat pump incorporated with heat recovery

International Nuclear Information System (INIS)

Shah, N.N.; Huang, M.J.; Hewitt, N.J.

2016-01-01

Highlights: • Diesel engine heat pump with heat recovery. • Water-to-water source heat pump based on R134a. • Possibility for different flow temperature for heat distribution system. • Possible retrofit application in off-gas or weak electricity network area. • Potential to diversify use of fossil fuel, primary energy and CO_2 emission savings. - Abstract: This paper presents experimental study of diesel engine heat pump (DEHP) system to find potential as retrofit technology in off-gas or weak electricity network area to replace existing gas/oil/electric heating system in domestic sector. Test set-up of diesel engine driven water-to-water heat pump system was built which included heat recovery arrangement from the engine coolant & exhaust gas. The system was designed to meet typical house heating demand in Northern Ireland. Performance of DEHP was evaluated to meet house-heating demand at different flow temperature (35, 45, 55 & 65 °C), a typical requirement of underfloor space heating, medium/high temperature radiators and domestic hot water. The performance was evaluated against four-evaporator water inlet temperature (0, 5, 10 & 15 °C) and at three different engine speed 1600, 2000 & 2400 rpm. Experiment results were analysed in terms of heating/cooling capacity, heat recovery, total heat output, primary energy ratio (PER), isentropic efficiency, etc. Test results showed that DEHP is able to meet house-heating demand with help of heat recovery with reduced system size. Heat recovery contributed in a range of 22–39% in total heat output. It is possible to achieve high flow temperature in a range of 74 °C with help of heat recovery. Overall system PER varied in a range of 0.93–1.33. Speed increment and flow temperature has significant impact on heat recovery, total heat output and PER. A case scenario with different flow temperature to match house-heating demand has been presented to show working potential with different heat distribution system

Does the time frame between exercise influence the effectiveness of hydrotherapy for recovery?

Science.gov (United States)

Halson, Shona L

2011-06-01

An increase in research investigating recovery strategies has occurred alongside the increase in usage of recovery by elite athletes. Because there is inconsistent evidence regarding the benefits of recovery on performance, it is necessary to examine research design to identify possible strategies that enhance performance in different athlete settings. The purpose of this review is to examine available recovery literature specifically related to the time frame between performance assessments to identify considerations for both research design and practical use of recovery techniques.

The software design of area γ radiation monitoring system

International Nuclear Information System (INIS)

Song Chenxin; Deng Changming; Cheng Chang; Ren Yi; Meng Dan; Liu Yun

2007-01-01

This paper main introduction the system structure, software architecture, design ideas of the area γ radiation monitoring system. Detailed introduction some programming technology about the computer communication with the local display unit. (authors)

The software design of area γ radiation monitoring system

International Nuclear Information System (INIS)

Song Chenxin; Deng Changming; Cheng Chang; Ren Yi; Meng Dan; Liu Yun

2008-01-01

This paper main introduction the system structure, software architecture, design ideas of the area γ radiation monitoring system. Detailed introduction some programming technology about the computer communication with the local display unit. (authors)

Carbon footprint of urban source separation for nutrient recovery.

Science.gov (United States)

Kjerstadius, H; Bernstad Saraiva, A; Spångberg, J; Davidsson, Å

2017-07-15

Source separation systems for the management of domestic wastewater and food waste has been suggested as more sustainable sanitation systems for urban areas. The present study used an attributional life cycle assessment to investigate the carbon footprint and potential for nutrient recovery of two sanitation systems for a hypothetical urban area in Southern Sweden. The systems represented a typical Swedish conventional system and a possible source separation system with increased nutrient recovery. The assessment included the management chain from household collection, transport, treatment and final return of nutrients to agriculture or disposal of the residuals. The results for carbon footprint and nutrient recovery (phosphorus and nitrogen) concluded that the source separation system could increase nutrient recovery (0.30-0.38 kg P capita -1 year -1 and 3.10-3.28 kg N capita -1 year -1 ), while decreasing the carbon footprint (-24 to -58 kg CO 2 -eq. capita -1 year -1 ), compared to the conventional system. The nutrient recovery was increased by the use of struvite precipitation and ammonium stripping at the wastewater treatment plant. The carbon footprint decreased, mainly due to the increased biogas production, increased replacement of mineral fertilizer in agriculture and less emissions of nitrous oxide from wastewater treatment. In conclusion, the study showed that source separation systems could potentially be used to increase nutrient recovery from urban areas, while decreasing the climate impact. Copyright © 2017 Elsevier Ltd. All rights reserved.

Designated rooting areas to reduce pasture damage by pregnant sows

NARCIS (Netherlands)

Mheen, van der H.; Spoolder, H.A.M.

2005-01-01

To assess whether rooting damage by pregnant sows can be reduced by offering a designated area for wallowing and foraging, four groups of four sows each were subjected to four treatments, during eight periods in a 4 × 4 Latin square designed experiment. During each period, each group was given

30 CFR 942.762 - Criteria for designating areas as unsuitable for surface coal mining operations.

Science.gov (United States)

2010-07-01

... the Tennessee Natural Areas Registry under Tennessee Code Annotated (TCA) section 11-14-112, Natural Areas designated by the Tennessee General Assembly under TCA 11-14-108, areas adjoining Tennessee Scenic Rivers designated under TCA 11-13-101, and Scenic Trails designated under TCA 11-11-101. ...

From heat integration targets toward implementation – A TSA (total site analysis)-based design approach for heat recovery systems in industrial clusters

International Nuclear Information System (INIS)

Hackl, Roman; Harvey, Simon

2015-01-01

The European process industry is facing major challenges to decrease production costs. One strategy to achieve this is by increasing energy efficiency. Single chemical processes are often well-integrated and the tools to target and design such measures are well developed. Site-wide heat integration based on total site analysis tools can be used to identify opportunities to further increase energy efficiency. However, the methodology has to be developed further in order to enable identification of practical heat integration measures in a systematic way. Designing site-wide heat recovery systems across an industrial cluster is complex and involves aspects apart from thermal process and utility flows. This work presents a method for designing a roadmap of heat integration investments based on total site analysis. The method is applied to a chemical cluster in Sweden. The results of the case study show that application of the proposed method can achieve up to 42% of the previously targeted hot utility savings of 129 MW. A roadmap of heat integration systems is suggested, ranging from less complex systems that achieve a minor share of the heat recovery potential to sophisticated, strongly interdependent systems demanding large investments and a high level of collaboration. - Highlights: • Methodology focused on the practical implementation of site-wide heat recovery. • Algorithm to determine a roadmap of heat integration investments. • Case study: 42% hot utility savings potential at a pay-back period of 3.9y.

Oracle Database 12c backup and recovery survival guide

CERN Document Server

Alvarez, Francisco Munoz

2013-01-01

The book follows a tutorial-based approach, covering all the best practices for backup and recovery. The book starts by introducing readers to the world of backup and recovery, then moves on to teach them the new features offered by Oracle 12c. The book is full of useful tips and best practices that are essential for any DBA to perform backup and recovery operations in an organization.This book is designed for Oracle DBAs and system administrators. The reader will have a basic working experience of administering Oracle databases. This book is designed for Oracle DBAs and system administrators.

Heat Recovery System

Science.gov (United States)

1984-01-01

Ball Metal's design of ducting and controls for series of roof top heat exchangers was inspired by Tech Briefs. Heat exchangers are installed on eight press and coating lines used to decorate sheet metal. The heat recovery system provides an estimated energy savings of more than $250,000 per year.

Simultaneous Recovery of Hydrogen and Chlorine from Industrial Waste Dilute Hydrochloric Acid

Directory of Open Access Journals (Sweden)

N. Paidimarri

2016-01-01

Full Text Available Recovery of chlorine from byproduct HCl has inevitable commercial importance in industries lately because of insufficient purity or too low concentration to recycle it. Instead it is being neutralized in industries before disposing to meet stringent environmental conditions. Although recovery through catalytic oxidation processes is studied since the 19th century, their high operating conditions combined with sluggish reaction kinetics and low single pass conversions make electrolysis a better alternative. The present motive of this work is to develop a novel electrolysis process which in contrast to traditional processes effectively recovers both hydrogen and chlorine from dilute HCl. For this, an electrolytic cell with an Anionic Exchange Membrane has been designed which only allows the passage of chlorine anions from catholyte to anolyte separating the gasses in a single step. The catholyte can be as low as 3.59 wt% because of fixed anolyte concentration of 1.99 wt% which minimizes oxygen formation. Preliminary results show that the simultaneous recovery of hydrogen and chlorine is possible with high conversion up to 98%. The maximum current density value for 4.96 cm2 membrane surface area (70% active surface area is 2.54 kAm−2, which is comparable with reported commercial processes. This study is expected to be useful for process intensification of the same in a continuous process environment.

The Place of Social Recovery in Mental Health and Related Services.

Science.gov (United States)

Ramon, Shulamit

2018-05-23

This article looks at the place of social recovery in mental health and social care services, alongside personal recovery. Despite its conceptual and practice centrality to the new meaning of recovery, social recovery has remained a relatively neglected dimension. This article attempts to provide an updated critical commentary based on findings from fifty nine studies, including a variety of research methodologies and methods. Definitions of social recovery within the new meaning of recovery are looked at. This is followed by outlining the development and significance of this dimension as reflected in the key areas of shared decision making, co-production and active citizenship, re-entering employment after experiencing mental ill health, being in employment, poverty and coping with poverty, the economic and the scientific cases for social recovery. The article highlights the connections between service users' experiencing mental health and social care systems, and the implications of ideologies and policies reflecting positions on social recovery. The complexity of social recovery is indicated in each of these areas; the related conceptual and methodological frameworks developed to research this dimension, and key achievements and barriers concerning everyday practice application of social recovery. The summary indicates potential future development perspectives of this dimension.

Understanding Interactions between Hydrogeologic Factors, Design Variables, and System Operations for Multi-Well Aquifer Storage and Recovery Systems

Science.gov (United States)

Majumdar, S.; Miller, G. R.; Smith, B.; Sheng, Z.

2017-12-01

Aquifer Storage and Recovery (ASR) system is a powerful tool for managing our present and future freshwater supplies. It involves injection of excess water into an aquifer, storing and later recovering it when needed, such as in a drought or during peak demand periods. Multi-well ASR systems, such as the Twin Oaks Facility in San Antonio, consist of a group of wells that are used for simultaneous injection and extraction of stored water. While significant research has gone into examining the effects of hydraulic and operational factors on recovery efficiency for single ASR well, little is known about how multi-well systems respond to these factors and how energy uses may vary. In this study, we created a synthetic ASR model in MODFLOW to test a range of multi-well scenarios. We altered design parameters (well spacing, pumping capacity, well configuration), hydrogeologic factors (regional hydraulic gradient, hydraulic conductivity, dispersivity), and operational variables (injection and withdrawal durations; pumping rates) to determine the response of the system across a realistic range of interrelated parameters. We then computed energy use for each simulation, based on the hydraulic head in each well and standard pump factors, as well as recovery efficiency, based on tracer concentration in recovered water from the wells. The tracer concentration in the groundwater was determined using MT3DMS. We observed that the recovery and energy efficiencies for the Multi-well ASR system decrease with the increase in well spacing and hydraulic gradient. When longitudinal dispersivity was doubled, the recovery and energy efficiencies were nearly halved. Another finding from our study suggests that we can recover nearly 90% of the water after two successive cycles of operation. The results will be used to develop generalized operational guidelines for meeting freshwater demands and also optimise the energy consumed during pumping.

Development of an end-of-life vehicle recovery model using system dynamics and future research needs

Science.gov (United States)

Mohamad-Ali, N.; Ghazilla, R. A. R.; Abdul-Rashid, S. H.; Sakundarini, N.; Ahmad-Yazid, A.; Stephenie, L.

2017-06-01

The implementation of end-of-life vehicle (ELV) recovery policy in Malaysia has led vehicle manufacturers to look at different ways to improve design and development of vehicles. Nowadays, it is crucial to incorporate end-of-life (EOL) design strategies into the vehicle design in order to enhance the effectiveness of the ELV recovery network. Although recent studies have shown that product design has a significant effect on the product recovery rate, there is a lack of studies on how EOL design strategies affects the effectiveness of ELV recovery, particularly when there are dynamic changes in the behaviour of the product recovery network. Thus, in this study, we developed a preliminary model based on the system dynamics approach in order to predict the effectiveness of ELV recovery in response to dynamic changes of various factors (including EOL design strategies) in the business environment. We developed this model based on preliminary data that we had gathered from unstructured interviews with the key stakeholders of ELV management in Malaysia. We believe that our model will greatly benefit product designers in incorporating the appropriate EOL design strategies in order to boost ELV recovery effectiveness in Malaysia.

Understanding Total Hip Replacement Recovery towards the Design of a Context-Aware Systems

NARCIS (Netherlands)

Jimenez Garcia, Juan

2011-01-01

Total Hip Replacement (THR) is a common procedure to improve the mobility of elderly with osteoarthritis. Presently information about the recovery process after discharge is unclear. As consequence patients and physiotherapists face uncertainties to follow an adequate trajectory for recovery.

Investigation of Chemical-Foam Design as a Novel Approach toward Immiscible Foam Flooding for Enhanced Oil Recovery.

Science.gov (United States)

Hosseini-Nasab, S M; Zitha, P L J

2017-10-19

Strong foam can be generated in porous media containing oil, resulting in incremental oil recovery; however, oil recovery factor is restricted. A large fraction of oil recovered by foam flooding forms an oil-in-water emulsion, so that costly methods may need to be used to separate the oil. Moreover, strong foam could create a large pressure gradient, which may cause fractures in the reservoir. This study presents a novel chemical-foam flooding process for enhanced oil recovery (EOR) from water-flooded reservoirs. The presented method involved the use of chemically designed foam to mobilize the remaining oil after water flooding and then to displace the mobilized oil to the production well. A blend of two anionic surfactant formulations was formulated for this method: (a) IOS, for achieving ultralow interfacial tension (IFT), and (b) AOS, for generating a strong foam. Experiments were performed using Bentheimer sandstone cores, where X-ray CT images were taken during foam generation to find the stability of the advancing front of foam propagation and to map the gas saturation for both the transient and the steady-state flow regimes. Then the proposed chemical-foam strategy for incremental oil recovery was tested through the coinjection of immiscible nitrogen gas and surfactant solutions with three different formulation properties in terms of IFT reduction and foaming strength capability. The discovered optimal formulation contains a foaming agent surfactant, a low IFT surfactant, and a cosolvent, which has a high foam stability and a considerably low IFT (1.6 × 10 -2 mN/m). Coinjection resulted in higher oil recovery and much less MRF than the same process with only using a foaming agent. The oil displacement experiment revealed that coinjection of gas with a blend of surfactants, containing a cosolvent, can recover a significant amount of oil (33% OIIP) over water flooding with a larger amount of clean oil and less emulsion.

75 FR 52780 - Designation of Nine Counties as High Intensity Drug Trafficking Areas

Science.gov (United States)

2010-08-27

... EXECUTIVE OFFICE OF THE PRESIDENT Office of National Drug Control Policy Designation of Nine Counties as High Intensity Drug Trafficking Areas ACTION: Notice. SUMMARY: The Director of the Office of National Drug Control Policy designated nine additional counties as High Drug Trafficking Areas pursuant to...

75 FR 21368 - Designation of Five Counties as High Intensity Drug Trafficking Areas

Science.gov (United States)

2010-04-23

... EXECUTIVE OFFICE OF THE PRESIDENT Office of National Drug Control Policy Designation of Five Counties as High Intensity Drug Trafficking Areas ACTION: Notice. SUMMARY: The Director of the Office of National Drug Control Policy designated five additional counties as High Drug Trafficking Areas pursuant to...

Fuzzy Logic Trajectory Design and Guidance for Terminal Area Energy Management

Science.gov (United States)

Burchett, Bradley

2003-01-01

The second generation reusable launch vehicle will leverage many new technologies to make flight to low earth orbit safer and more cost effective. One important capability will be completely autonomous flight during reentry and landing, thus making it unnecessary to man the vehicle for cargo missions with stringent weight constraints. Implementation of sophisticated new guidance and control methods will enable the vehicle to return to earth under less than favorable conditions. The return to earth consists of three phases--Entry, Terminal Area Energy Management (TAEM), and Approach and Landing. The Space Shuttle is programmed to fly all three phases of flight automatically, and under normal circumstances the astronaut-pilot takes manual control only during the Approach and Landing phase. The automatic control algorithms used in the Shuttle for TAEM and Approach and Landing have been developed over the past 30 years. They are computationally efficient, and based on careful study of the spacecraft's flight dynamics, and heuristic reasoning. The gliding return trajectory is planned prior to the mission, and only minor adjustments are made during flight for perturbations in the vehicle energy state. With the advent of the X-33 and X-34 technology demonstration vehicles, several authors investigated implementing advanced control methods to provide autonomous real-time design of gliding return trajectories thus enhancing the ability of the vehicle to adjust to unusual energy states. The bulk of work published to date deals primarily with the approach and landing phase of flight where changes in heading angle are small, and range to the runway is monotonically decreasing. These benign flight conditions allow for model simplification and fairly straightforward optimization. This project focuses on the TAEM phase of flight where mathematically precise methods have produced limited results. Fuzzy Logic methods are used to make onboard autonomous gliding return trajectory

Water Recovery System Design to Accommodate Dormant Periods for Manned Missions

Science.gov (United States)

Tabb, David; Carter, Layne

2015-01-01

Future manned missions beyond lower Earth orbit may include intermittent periods of extended dormancy. Under the NASA Advanced Exploration System (AES) project, NASA personnel evaluated the viability of the ISS Water Recovery System (WRS) to support such a mission. The mission requirement includes the capability for life support systems to support crew activity, followed by a dormant period of up to one year, and subsequently for the life support systems to come back online for additional crewed missions. Dormancy could be a critical issue due to concerns with microbial growth or chemical degradation that might prevent water systems from operating properly when the crewed mission began. As such, it is critical that the water systems be designed to accommodate this dormant period. This paper details the results of this evaluation, which include identification of dormancy issues, results of testing performed to assess microbial stability of pretreated urine during dormancy periods, and concepts for updating to the WRS architecture and operational concepts that will enable the ISS WRS to support the dormancy requirement.

Development of a recovery education program for inpatient mental health providers.

Science.gov (United States)

Chen, Shu-Ping; Krupa, Terry; Lysaght, Rosemary; McCay, Elizabeth; Piat, Myra

2014-12-01

Mental health system transformation toward a recovery-orientation has created a demand for education to equip providers with recovery competencies. This report describes the development of a recovery education program designed specifically for inpatient providers. Part 1 of the education is a self-learning program introducing recovery concepts and a recovery competency framework; Part 2 is a group-learning program focusing on real-life dilemmas and applying the Appreciative Inquiry approach to address these clinical dilemmas. A pilot study with a pretest/posttest design was used to evaluate the program. Participants included 26 inpatient multidisciplinary providers from 3 hospitals. The results showed participants' improvement on recovery knowledge (z = -2.55, p = .011) after the self-learning program. Evaluations of the group-learning program were high (4.21 out of 5). These results support continued efforts to refine the program. Inpatient providers could use this program to lead interprofessional practice in promoting recovery. (c) 2014 APA, all rights reserved.

Optimization of Mineral Separator for Recovery of Total Heavy Minerals of Bay of Bengal using Central Composite Design

Science.gov (United States)

Routray, Sunita; Swain, Ranjita; Rao, Raghupatruni Bhima

2017-04-01

The present study is aimed at investigating the optimization of a mineral separator for processing of beach sand minerals of Bay of Bengal along Ganjam-Rushikulya coast. The central composite design matrix and response surface methodology were applied in designing the experiments to evaluate the interactive effects of the three most important operating variables, such as feed quantity, wash water rate and Shake amplitude of the deck. The predicted values were found to be in good agreement with the experimental values (R2 = 0.97 for grade and 0.98 for recovery). To understand the impact of each variable, three dimensional (3D) plots were also developed for the estimated responses.

Conceptual design of a high current ISOL target area at TRIUMF

International Nuclear Information System (INIS)

Beveridge, J.L.; Buchmann, L.; Clark, G.S.; Sprenger, H.; Thorson, I.; Vincent, J.; D'Auria, J.M.; Dombsky, M.

1993-05-01

Two similar conceptual designs for the handling of highly activated components at the target area of a high current radioactive beam facility have been investigated. The proposed designs are sufficiently flexible that practical detailed designs could be realized. Personnel exposure to radiation during the handling procedures is expected to be minimal. (author) 3 refs., 4 figs

Is it time to turn our attention towards central mechanisms for post-exertional recovery strategies and performance?

Directory of Open Access Journals (Sweden)

Ben eRattray

2015-03-01

Full Text Available Post-exercise recovery has largely focused on peripheral mechanisms of fatigue, but there is growing acceptance that fatigue is also contributed to through central mechanisms which demands that attention should be paid to optimising recovery of the brain. In this narrative review we assemble evidence for the role that many currently utilised recovery strategies may have on the brain, as well as potential mechanisms for their action. The review provides discussion of how common nutritional strategies as well as physical modalities and methods to reduce mental fatigue are likely to interact with the brain, and offer an opportunity for subsequent improved performance. We aim to highlight the fact that many recovery strategies have been designed with the periphery in mind, and that refinement of current methods are likely to provide improvements in minimising central fatigue. Whilst we offer a number of recommendations, it is evident that there are many opportunities for improving the research, and practical guidelines in this area.

Modelling post-fire vegetation recovery in Portugal

Directory of Open Access Journals (Sweden)

A. Bastos

2011-12-01

Full Text Available Wildfires in Mediterranean Europe have been increasing in number and extension over the last decades and constitute one of the major disturbances of these ecosystems. Portugal is the country with more burnt area in the last decade and the years of 2003 and 2005 were particularly devastating, the total burned areas of 425 000 and 338 000 ha being several times higher than the corresponding average. The year of 2005 further coincided with one of the most severe droughts since early 20th century. Due to different responses of vegetation to diverse fire regimes and to the complexity of landscape structures, fires have complex effects on vegetation recovery. Remote sensing has revealed to be a powerful tool in studying vegetation dynamics and in monitoring post-fire vegetation recovery, which is crucial to land-management and to prevent erosion.

The main goals of the present work are (i to assess the accuracy of a vegetation recovery model previously developed by the authors; (ii to assess the model's performance, namely its sensitivity to initial conditions, to the temporal length of the input dataset and to missing data; (iii to study vegetation recovery over two selected areas that were affected by two large wildfire events in the fire seasons of 2003 and 2005, respectively.

The study relies on monthly values of NDVI over 11 years (1998–2009, at 1 km × 1 km spatial resolution, as obtained by the VEGETATION instrument. According to results from sensitivity analysis, the model is robust and able to provide good estimations of recovery times of vegetation when the regeneration process is regular, even when missing data is present. In respect to the two selected burnt scars, results indicate that fire damage is a determinant factor of regeneration, as less damaged vegetation recovers more rapidly, which is mainly justified by the high coverage of Pinus pinaster over the area, and by the fact that coniferous forests tend to

Exploitation study of the ore-body ''Tigre III''. Open-cut design and study of high-recovery underground mining method for the Tigre III ore-body

International Nuclear Information System (INIS)

Baluszka, J.C.

1980-01-01

The paper first carries out an analysis for the purpose of determining the limiting sterile/ore ratio for open-cut and underground mining in the specific filling case of Tigre III. In this connection it considers a high-recovery method of underground mining (involving the use of cemented hydropneumatic chambers), a general mine plan covering access, transport, ventilation and removal of ore as well as auxiliary services relating to the Tigre III ore body as a whole. The costs of this method of mining are determined for purposes of comparison with the open-cut method. Similarly, the limiting sterile/ore ratio is taken as the basis for an analysis of different types of pit and a design suited to the limiting ratio is adopted. As a final solution the paper favours a method which combines open-cut and underground mining. It proposes the use of the open-cut method up to the limiting ratio (in accordance with the pit design chosen) and of underground method (by the filling chamber method) for the rest of the area. (author)

Heat recovery apparatus

International Nuclear Information System (INIS)

McFarland, I.

1987-01-01

Heat transfer is a living science and technical advances are constantly being made. However, in many cases, progress is limited by the equipment that is available on the market, rather than by knowledge of the heat transfer process. A case in point is the design of economizers: in such equipment a small quantity of water (with a relatively good heat transfer coefficient) is heated by a large quantity of low-pressure gas (with an inherently low heat transfer coefficient). As a first step in design finned tubing is used to lessen the discrepancy in coefficients. From this point, it becomes apparent that the equipment consists of a small number of tubes (to maintain good velocity on the water side) of considerable length (to provide sufficient area). In the process industries the base pressure, though low, may be in the region of 0.5 bar, and there is no convenient flue in which to place the heat recovery coil. It is therefore contained in a flat-sided enclosure, which is ill-fitted to pressure containment and is therefore reinforced with a plethora of structural sections. Such inelegant construction is quite common in North America; in Europe, cylindrical containments of vast size have been supplied for the same purposes. The real shortcoming is a successful marriage of different disciplines to produce reliable and efficient heat transfer equipment suitably contained

Energy efficiency improvement of a Kraft process through practical stack gases heat recovery

International Nuclear Information System (INIS)

Mostajeran Goortani, B.; Mateos-Espejel, E.; Moshkelani, M.; Paris, J.

2011-01-01

A process scheme for the optimal recovery of heat from stack gases considering energy and technical constraints has been developed and applied to an existing Kraft pulping mill. A system based on a closed loop recirculation of hot oil is used to recover the heat from stack gases and distribute it to the appropriate cold streams. The recovery of heat from stack gases is part of an overall optimization of the Kraft mill. Tools such as Pinch Analysis and exergy analysis are used to evaluate the process streams. The results indicate that 10.8 MW of heat from stack gases can be reused to heat process streams such as the deaerator water, hot water, drying filtrates, and black liquor. A simulation model of the recirculation loop has been developed to determine the specifications of the recovery system. The total heat exchanger surface area required by the system is 3460 m 2 , with a hot oil recirculation temperature of 137 o C. The anticipated total investment is $10.3 M, with a payback time of 1.8 years. - Highlights: → We developed a process design for recovering heat from stack gases in a Kraft mill. → The recovered heat is optimally distributed to the process cold streams. → Heat recovery system has a total surface area of 3500 m 2 without gases condensation. → A reduction of 7 percent in total process steam demand is anticipated. → A total investment of 10.3 M$ is needed with a payback time of less than two years

Further development of recovery boiler; Soodakattilan kehitystyoe

Energy Technology Data Exchange (ETDEWEB)

Janka, K.; Siiskonen, P.; Sundstroem, K. [Tampella Power Oy, Tampere (Finland)] [and others

1996-12-01

The global model of a recovery boiler was further developed. The aim is to be able to model the velocity, temperature and concentration fields in a boiler. At this moment the model includes submodels for: droplet drying, pyrolysis, char burning, gas burning and for droplet trajectory. The preliminary study of NO{sub x} and fly ash behaviour in a boiler was carried out. The study concerning flow field in the superheater area was carried out a 2-dimensional case in which the inflow parameters were taken from global model of a recovery boiler. Further the prediction methods of fouling in a recovery boiler were developed based on theoretical calculations of smelting behaviour of multicomponent mixtures and measurements at operating recovery boilers. (author)

Perceptions about recovery needs and drug-avoidance recovery behaviors among youth in substance abuse treatment.

Science.gov (United States)

Gonzales, Rachel; Anglin, M Douglas; Glik, Deborah C; Zavalza, Christina

2013-01-01

This study used mixed methods to explore youth attitudes about recovery-related needs and important drug-avoidance behaviors after treatment. Focus groups were conducted with 118 substance using youth in treatment (four residential and 10 outpatient settings) throughout Los Angeles County. The average age was 17.4 (SD = 2.9); 78.3% were male, 66.1% Latino; and most were in treatment for primary marijuana (40.9%) or methamphetamine (30.4%) abuse. Quantitatve results from the drug-avoidance activity survey identified the following factors youth rated as important to their recovery after treatment: lifestyle improvement activities (95.7%); changing personal drug behaviors (89.6%); drug environment/culture change activities (82.5%); with the least important being therapeutic activities (78.5%). Qualitative findings from focus groups that asked what youth think are important for recovery programs to address after treatment revealed the following four areas: (1) recovery promotion to developmentally appropriate activities (95%); (2) facilitating the use of coping skills to deal with stress (85%); (3) offering alternative recovery support options (not just abstinence only) (75%); and (4) continuing to provide substance use education (65%). Findings highlight essential aspects of recovery in terms of need and drug-avoidance behaviors considered important to youth in treatment. Such information will help to better address clinical and recovery support models aimed at relapse prevention to ensure that the perceived problems of substance-abusing youth are adequately met.

Design and construction of the main linac module for the superconducting energy recovery linac project at Cornell

Energy Technology Data Exchange (ETDEWEB)

Eichhorn, R.; Bullock, B.; He, Y.; Hoffstaetter, G.; Liepe, M.; O' Connell, T.; Quigley, P.; Sabol, D.; Sears, J.; Smith, E.; Veshcherevich, V. [Cornell Laboratory for Accelerator-based Science and Education (CLASSE), Cornell University, 161 Synchrotron Drive, Ithaca, NY 14853 (United States)

2014-01-29

Cornell University has been designing and building superconducting accelerators for various applications for more than 50 years. Currently, an energy-recovery linac (ERL) based synchrotron-light facility is proposed making use of the existing CESR facility. As part of the phase 1 R and D program funded by the NSF, critical challenges in the design were addressed, one of them being a full linac cryo-module. It houses 6 superconducting cavities- operated at 1.8 K in continuous wave (CW) mode - with individual HOM absorbers and one magnet/ BPM section. Pushing the limits, a high quality factor of the cavities (2⋅10{sup 10}) and high beam currents (100 mA accelerated plus 100 mA decelerated) are targeted. We will present the design of the main linac cryo-module (MLC) being finalized recently, its cryogenic features and report on the status of the fabrication which started in late 2012.

Bench Blasting Design for Optimum Recovery of Blocks in ...

African Journals Online (AJOL)

In this research work, breaking factor is used in place of powder factor since breaking is required not powder. The aim of this research work is to establish a standard breaking factor for bench blasting in dimension quarries that will improve recovery. Two cases were considered. In case 1, gun powder is used for basal ...

Recovery and Performance in Sport: Consensus Statement.

Science.gov (United States)

Kellmann, Michael; Bertollo, Maurizio; Bosquet, Laurent; Brink, Michel; Coutts, Aaron J; Duffield, Rob; Erlacher, Daniel; Halson, Shona L; Hecksteden, Anne; Heidari, Jahan; Kallus, K Wolfgang; Meeusen, Romain; Mujika, Iñigo; Robazza, Claudio; Skorski, Sabrina; Venter, Ranel; Beckmann, Jürgen

2018-02-01

The relationship between recovery and fatigue and its impact on performance has attracted the interest of sport science for many years. An adequate balance between stress (training and competition load, other life demands) and recovery is essential for athletes to achieve continuous high-level performance. Research has focused on the examination of physiological and psychological recovery strategies to compensate external and internal training and competition loads. A systematic monitoring of recovery and the subsequent implementation of recovery routines aims at maximizing performance and preventing negative developments such as underrecovery, nonfunctional overreaching, the overtraining syndrome, injuries, or illnesses. Due to the inter- and intraindividual variability of responses to training, competition, and recovery strategies, a diverse set of expertise is required to address the multifaceted phenomena of recovery, performance, and their interactions to transfer knowledge from sport science to sport practice. For this purpose, a symposium on Recovery and Performance was organized at the Technical University Munich Science and Study Center Raitenhaslach (Germany) in September 2016. Various international experts from many disciplines and research areas gathered to discuss and share their knowledge of recovery for performance enhancement in a variety of settings. The results of this meeting are outlined in this consensus statement that provides central definitions, theoretical frameworks, and practical implications as a synopsis of the current knowledge of recovery and performance. While our understanding of the complex relationship between recovery and performance has significantly increased through research, some important issues for future investigations are also elaborated.

Damage Recovery in Carrara Marble

Science.gov (United States)

Meyer, G.; Brantut, N.; Mitchell, T. M.; Meredith, P. G.

2017-12-01

We investigate the effect of confining pressure on the recovery of elastic wave velocities following deformation episodes in Carrara Marble. Dry Carrara Marble cores were deformed in the ductile regime (Pc = 40 MPa) up to 3% axial strain. After deformation, samples were held at constant stress conditions for extended periods of time (5-8 days) whilst continuously recording volumetric strain and seismic wave velocities. The velocity data were used to invert for microcrack densities using an effective medium approach. Finally, thin sections were produced to characterise the microstructures after recovery. During deformation, elastic wave speeds decreased with increasing strain by more than 30% of the value for the intact rock due to the formation of distributed microcracks. Under constant hydrostatic pressure, wave speeds progressively recovered 12-90% of the initial drop, depending on the applied confining pressure. In contrast, the strain recovery (deformation towards the initial shape of the sample) during holding time is negligible (of the order of 10-4). Tests performed under nonhydrostatic (triaxial) stress conditions during recovery showed some time-dependent creep deformation together with very significant recovery of wave velocities. The recovery is interpreted as a progressive reduction in crack density within the sample. The process is highly dependent on confining pressure, which favours it. We propose that the driving process for wave speed recovery is the time-dependent increase of contact area between crack surfaces due to the formation and growth of asperity contacts. We develop a micromechanical model for crack closure driven by asperity creep, which shows a good fit to the experimental data. Most of the recovery is achieved in the initial few hours, implying it is the fastest recovery or healing process, and thus occurs prior to any chemical healing or mineral precipitation. Our data corroborate field observations of post-seismic fault behavior.

Relationship intention and satisfaction following service recovery: The mediating role of perceptions of service recovery in the cell phone industry

Directory of Open Access Journals (Sweden)

L Kruger

2015-11-01

Full Text Available In an industry characterised by fierce competition, cell phone network providers find it increasingly difficult to retain their customers after service failure. It is therefore essential for cell phone network providers to offer effective service recovery when they attempt to restore customer satisfaction following service failure. As it has been argued that relationships between customers and service providers should be considered a key determinant of the service recovery required to restore post-recovery attitudes and behavioural intentions, the purpose of this study was to determine the relationships between South African cell phone customers’ relationship intentions, their perceptions of service recovery and their satisfaction following service recovery. Personal in-home interviews were conducted to collect data from 605 cell phone customers residing in the Johannesburg metropolitan area. In addition to the significant positive relationships found between cell phone users’ relationship intentions, perceived service recovery and satisfaction after service recovery, this study found that perceived service recovery played a mediating role in the relationship between relationship intention and satisfaction following service recovery. The study concludes that, although a direct relationship exists between relationship intention and satisfaction following service recovery, perceived service recovery plays an additional indirect complementary role in this relationship. It is recommended that, in addition to focusing their relationship efforts on customers with relationship intentions, cell phone network providers also offer positively perceived service recovery to these customers, as this would lead to greater satisfaction following service recovery.

Type 'A' and 'B' recovery revisited: The role of field-edge habitats for Collembola and macroarthropod community recovery after insecticide treatment

Energy Technology Data Exchange (ETDEWEB)

Frampton, Geoff K. [Ecology and Evolutionary Biology Group, School of Biological Sciences, University of Southampton, Bassett Crescent East, Southampton SO16 7PX (United Kingdom)]. E-mail: gkf@soton.ac.uk; Gould, Philip J.L. [Ecology and Evolutionary Biology Group, School of Biological Sciences, University of Southampton, Bassett Crescent East, Southampton SO16 7PX (United Kingdom); Brink, Paul J. van den [Alterra, Wageningen University and Research Centre, P.O. Box 47, 6700 AA Wageningen (Netherlands); Department of Aquatic Ecology and Water Quality Management, Wageningen University, Wageningen University and Research Centre, Wageningen (Netherlands); Hendy, Eleanor [Ecology and Evolutionary Biology Group, School of Biological Sciences, University of Southampton, Bassett Crescent East, Southampton SO16 7PX (United Kingdom)

2007-02-15

Previous work has identified two patterns of arthropod recovery after insecticide applications to arable crops: dispersal-mediated recolonisation from untreated areas (Type A) and recolonisation within treated areas assisted by reduced predation (Type B). In this study, connectivity between field-edge habitats was manipulated using barriers to investigate whether a crop edge and adjacent hedgerow influence recolonisation of an insecticide-treated crop by surface-active Collembola and other arthropods. Collembola recovery patterns differed among closely-related taxa. Epigeic collembolan and macroarthropod communities were more diverse and abundant, and rates of artificial prey predation were higher, in sprayed crop areas connected to both hedgerow and unsprayed crop edge than in sprayed areas connected to the unsprayed edge alone. These findings indicate that effectiveness of unsprayed crop edges as sources of field recolonisation may depend on adjoining field margin habitats. An assumption in risk assessment that unsprayed crop edges assist population recovery within treated areas is not supported. - Collembola recolonisation differs among species; effectiveness of unsprayed crop edges as sources of arthropod recolonisation may depend on adjacent habitat.

High speed fiber optics local area networks: Design and implementation

Science.gov (United States)

Tobagi, Fouad A.

1988-01-01

The design of high speed local area networks (HSLAN) for communication among distributed devices requires solving problems in three areas: (1) the network medium and its topology; (2) the medium access control; and (3) the network interface. Considerable progress has been made in all areas. Accomplishments are divided into two groups according to their theoretical or experimental nature. A brief summary is given in Section 2, including references to papers which appeared in the literature, as well as to Ph.D. dissertations and technical reports published at Stanford University.

Fructification phenology as an important tool in the recovery of iron mining areas in Minas Gerais, Brazil.

Science.gov (United States)

Garcia, L C; Barros, F V; Lemos-Filho, J P

2009-08-01

'Canga' is a name given to the ferruginous rocky fields that can be found in the 'Quadrilátero Ferrífero' of Minas Gerais, Brazil. The endemism and species richness make them areas of special biological importance, regarded as high-priority for conservation. Nevertheless, they are being threatened by intense mining activity. Aiming to understand more about this flora, this study was performed in order to determine the maturation or dispersal period of the fruits of four Canga species, Alibertia vaccinioides K.Schum. (Rubiaceae), Coccoloba acrostichoides Cham. (Polygonaceae), Miconia sellowiana Naudin (Melastomataceae), and one probable new species of Calyptranthes Sw. (Myrtaceae). Although fruit maturation or dispersal tended to occur at the end of the dry season, some asynchrony was observed in these species, with food sources being available during most of the year. This shows that these species have the potential to attract animals the whole year round, and planting them for the recovery of iron mining areas may increase the community's self-regeneration capacity, leading to a more successful restoration process.

Fructification phenology as an important tool in the recovery of iron mining areas in Minas Gerais, Brazil

Directory of Open Access Journals (Sweden)

LC. Garcia

Full Text Available "Canga" is a name given to the ferruginous rocky fields that can be found in the "Quadrilátero Ferrífero" of Minas Gerais, Brazil. The endemism and species richness make them areas of special biological importance, regarded as high-priority for conservation. Nevertheless, they are being threatened by intense mining activity. Aiming to understand more about this flora, this study was performed in order to determine the maturation or dispersal period of the fruits of four Canga species, Alibertia vaccinioides K.Schum. (Rubiaceae, Coccoloba acrostichoides Cham. (Polygonaceae, Miconia sellowiana Naudin (Melastomataceae, and one probable new species of Calyptranthes Sw. (Myrtaceae. Although fruit maturation or dispersal tended to occur at the end of the dry season, some asynchrony was observed in these species, with food sources being available during most of the year. This shows that these species have the potential to attract animals the whole year round, and planting them for the recovery of iron mining areas may increase the community's self-regeneration capacity, leading to a more successful restoration process.

77 FR 59629 - Statutorily Mandated Designation of Difficult Development Areas for 2013

Science.gov (United States)

2012-09-28

... ranking ratio, as described above, was identical (to four decimal places) to the last area selected, and... questions on how areas are designated and on geographic definitions, contact Michael K. Hollar, Senior... year. 2010 Census, 2000 Census, and Metropolitan Area Definitions Data from the 2010 Census on total...

A decade of mangrove recovery at affected area by the 2004 tsunami along coast of Banda Aceh city

Science.gov (United States)

Onrizal; Mansor, M.

2018-03-01

Banda Aceh (BA) is the capital of Aceh Province, Indonesia. It was the most affected areas by the 2004 tsunami. Before the natural catastrophe, most of the BA mangroves disturbed by human activities and remaining mangroves were fragmented and had a low density of trees. Therefore, the objectives of this study were to calculate the impact of the tsunami on mangrove and subsequently to evaluate the mangrove recovery based on spatial and temporal analysis and ground truthing method within the period 11 years in intertidal areas of BA. Three regions of BA coastal areas were selected, namely Kuala Cangkoy, Gampong Jawa and Lambada coasts. Before the tsunami, the mangrove forests in BA were only 13.6% of BA coastlands and fragmented. Approximately 48.9% of the mangroves have destroyed due to the tsunami. The BA mangroves at 5 and 11 years after tsunami were 66.5% and 81.3% relative to the data before tsunami, respectively. It means that the BA is very vulnerable due to the future tsunami occur. Therefore, the mangrove restoration in BA needs to be improved and maintain based on green belt concept for coastal protection as well as productivity of estuarine ecosystem.

Analytical study on different blade-shape design of HAWT for wasted kinetic energy recovery system (WKERS)

Science.gov (United States)

Goh, J. B.; Jamaludin, Z.; Jafar, F. A.; Mat Ali, M.; Mokhtar, M. N. Ali; Tan, C. H.

2017-06-01

Wasted kinetic energy recovery system (WKERS) is a wind renewable gadget installed above a cooling tower outlet to harvest the discharged wind for electrical regeneration purpose. The previous WKERS is operated by a horizontal axis wind turbine (HAWT) with delta blade design but the performance is still not at the optimum level. Perhaps, a better blade-shape design should be determined to obtain the optimal performance, as it is believed that the blade-shape design plays a critical role in HAWT. Hence, to determine a better blade-shape design for a new generation of WKERS, elliptical blade, swept blade and NREL Phase IV blade are selected for this benchmarking process. NREL Phase IV blade is a modern HAWT’s blade design by National Renewable Energy Laboratory (NREL) research lab. During the process of benchmarking, Computational Fluid Dynamics (CFD) analysis was ran by using SolidWorks design software, where all the designs are simulated with linear flow simulation. The wind speed in the simulation is set at 10.0 m/s, which is compatible with the average wind speed produced by a standard size cooling tower. The result is obtained by flow trajectories of air motion, surface plot and cut plot of the applied blade-shape. Besides, the aspect ratio of each blade is calculated and included as one of the reference in the comparison. Hence, the final selection of the best blade-shape design will bring to the new generation of WKERS.

Performance assessment techniques for groundwater recovery and treatment systems

Energy Technology Data Exchange (ETDEWEB)

Kirkpatrick, G.L. [Environmental Resources Management, Inc., Exton, PA (United States)

1993-03-01

Groundwater recovery and treatment (pump and treat systems) continue to be the most commonly selected remedial technology for groundwater restoration and protection programs at hazardous waste sites and RCRA facilities nationwide. Implementing a typical groundwater recovery and treatment system includes the initial assessment of groundwater quality, characterizing aquifer hydrodynamics, recovery system design, system installation, testing, permitting, and operation and maintenance. This paper focuses on methods used to assess the long-term efficiency of a pump and treat system. Regulatory agencies and industry alike are sensitive to the need for accurate assessment of the performance and success of groundwater recovery systems for contaminant plume abatement and aquifer restoration. Several assessment methods are available to measure the long-term performance of a groundwater recovery system. This paper presents six assessment techniques: degree of compliance with regulatory agency agreement (Consent Order of Record of Decision), hydraulic demonstration of system performance, contaminant mass recovery calculation, system design and performance comparison, statistical evaluation of groundwater quality and preferably, integration of the assessment methods. Applying specific recovery system assessment methods depends upon the type, amount, and quality of data available. Use of an integrated approach is encouraged to evaluate the success of a groundwater recovery and treatment system. The methods presented in this paper are for engineers and corporate management to use when discussing the effectiveness of groundwater remediation systems with their environmental consultant. In addition, an independent (third party) system evaluation is recommended to be sure that a recovery system operates efficiently and with minimum expense.

Mega-fire Recovery in Dry Conifer Forests of the Interior West

Science.gov (United States)

Malone, S. L.; Fornwalt, P.; Chambers, M. E.; Battaglia, M.

2015-12-01

Wildfire is a complex landscape process with great uncertainty in whether trends in size and severity are shifting trajectories for ecosystem recovery that are outside of the historical range of variability. Considering that wildfire size and severity is likely to increase into the future with a drier climate, it is important that we understand wildfire effects and ecosystem recovery. To evaluate how ecosystems recover from wildfire we measured spatial patterns in regeneration and mapped tree refugia within mega-fire perimeters (Hayman, Jasper, Bobcat, and Grizzly Gulch) in ponderosa pine (Pinus ponderosa) dominated forest. On average, high severity fire effects accounted for > 15% of burned area and increased with fire size. Areas with high severity fire effects contained 1 - 15% tree refugia cover, compared to 37 - 70% observed in low severity areas . Large high severity patches with low coverage of tree refugia, were more frequent in larger fires and regeneration distances required to initiate forest recovery far exceeded 1.5 canopy height or 200 m, distances where the vast majority of regeneration is likely to arise. Using a recovery model driven by distance, we estimate recovery times between 300 to > 1000 years for these mega-fires. In Western dry conifer forests, large patches of stand replacing fire are likely to lead to uneven aged forest and very long recovery times.

Strategy paper. Remedial design/remedial action 100 Area. Revision 1

International Nuclear Information System (INIS)

Donahoe, R.L.

1995-07-01

The purpose of this planning document is to identify and define the approach for remedial design and remedial action (RD/RA) in the 100 Area of the Hanford Site, located in southeastern Washington State. Additionally, this document will support the Hanford Site Environmental Restoration Contract (ERC) team, the US Department of Energy (DOE), and regulatory agencies in identifying and agreeing upon the complete process for expedited cleanup of the 100 Area

The Recovery Knowledge Inventory for Measurement of Nursing Student Views on Recovery-oriented Mental Health Services.

Science.gov (United States)

Happell, Brenda; Byrne, Louise; Platania-Phung, Chris

2015-01-01

Recovery-oriented services are a goal for policy and practice in the Australian mental health service system. Evidence-based reform requires an instrument to measure knowledge of recovery concepts. The Recovery Knowledge Inventory (RKI) was designed for this purpose, however, its suitability and validity for student health professionals has not been evaluated. The purpose of the current article is to report the psychometric features of the RKI for measuring nursing students' views on recovery. The RKI, a self-report measure, consists of four scales: (I) Roles and Responsibilities, (II) Non-Linearity of the Recovery Process, (III) Roles of Self-Definition and Peers, and (IV) Expectations Regarding Recovery. Confirmatory and exploratory factor analyses of the baseline data (n = 167) were applied to assess validity and reliability. Exploratory factor analyses generally replicated the item structure suggested by the three main scales, however more stringent analyses (confirmatory factor analysis) did not provide strong support for convergent validity. A refined RKI with 16 items had internal reliabilities of α = .75 for Roles and Responsibilities, α = .49 for Roles of Self-Definition and Peers, and α = .72, for Recovery as Non-Linear Process. If the RKI is to be applied to nursing student populations, the conceptual underpinning of the instrument needs to be reworked, and new items should be generated to evaluate and improve scale validity and reliability.

Design for a 1.3 MW, 13 MeV Beam Dump for an Energy Recovery Linac

CERN Document Server

Sinclair, Charles K; Smith, Colin H

2005-01-01

The electron beam exiting an Energy Recovery Linac (ERL) is dumped close to the injection energy. This energy is chosen as low as possible while allowing the beam quality specifications to be met. As ERLs are designed for high average beam current, beam dumps are required to handle high beam power at low energy. Low energy electrons have a short range in practical dump materials, requiring the beam size at the dump face be enlarged to give acceptable power densities and heat fluxes. Cornell University is developing a 100 mA average current ERL as a synchrotron radiation source. The 13 MeV optimum injection energy requires a 1.3 MW beam dump. We present a mature design for this dump, using an array of water-cooled extruded copper tubes. This array is mounted in the accelerator vacuum normal to the beam. Fatigue failure resulting from abrupt thermal cycles associated with beam trips is a potential failure mechanism. We report on designs for a 75 kW, 750 keV tube-cooled beryllium plate dump for electron gun test...

Recovery of personal neglect.

Science.gov (United States)

Iosa, Marco; Guariglia, Cecilia; Matano, Alessandro; Paolucci, Stefano; Pizzamiglio, Luigi

2016-12-01

Extrapersonal unilateral spatial neglect after stroke is associated to a poor rehabilitation outcome. Minor attention has been paid to the recovery of personal neglect, to its relationship with the recovery of extrapersonal neglect and of independency in activities of daily living. The present study aims at evaluating whether there is an association between recovery of extrapersonal and personal neglect. The secondary aim was to investigate if personal neglect may affect the effectiveness of neurorehabilitation in patients with subacute stroke. Observational study. Neurorehabilitation Hospital in Rome, Italy, inpatients. A sample of 49 patients with unilateral spatial neglect resulting from right ischemic cerebral infarction was enrolled in this study, divided into three subgroups according to the presence and the degree of personal neglect, and evaluated pre and postneurorehabilitation. Personal neglect was evaluated using Zoccolotti and Judica's Scale, extrapersonal neglect using Letter Cancellation Test, Barrage Test, Sentence Reading Test and Wundt-Jastrow Area Illusion Test. Barthel Index (BI), Rivermead Mobility Index, and Canadian Neurological Scale were also administered. Results showed the following: 1) recovery of personal neglect was not significantly correlated with that of extrapersonal neglect, despite both the disorders were ameliorated after a "non-specific" rehabilitation treatment; 2) personal neglect per se was not an additional negative prognostic factor in the rehabilitation findings. Our results suggested that the recoveries of the two types of neglect are independent from each other, and that the presence of personal neglect does not imply significant additional problems to the functional outcomes. Our study highlighted the need of novel tools to assess the presence and to improve the recovery of personal neglect.

Improving Energy Efficiency In Thermal Oil Recovery Surface Facilities

Energy Technology Data Exchange (ETDEWEB)

Murthy Nadella, Narayana

2010-09-15

Thermal oil recovery methods such as Cyclic Steam Stimulation (CSS), Steam Assisted Gravity Drainage (SAGD) and In-situ Combustion are being used for recovering heavy oil and bitumen. These processes expend energy to recover oil. The process design of the surface facilities requires optimization to improve the efficiency of oil recovery by minimizing the energy consumption per barrel of oil produced. Optimization involves minimizing external energy use by heat integration. This paper discusses the unit processes and design methodology considering thermodynamic energy requirements and heat integration methods to improve energy efficiency in the surface facilities. A design case study is presented.

The development of the Be Active & Relax “Vitality in Practice” (VIP project and design of an RCT to reduce the need for recovery in office employees

Directory of Open Access Journals (Sweden)

Coffeng Jennifer K

2012-08-01

Full Text Available Abstract Background There is strong evidence to suggest that multiple work-related health problems are preceded by a higher need for recovery. Physical activity and relaxation are helpful in decreasing the need for recovery. This article aims to describe (1 the development and (2 the design of the evaluation of a daily physical activity and relaxation intervention to reduce the need for recovery in office employees. Methods/Design The study population will consist of employees of a Dutch financial service provider. The intervention was systematically developed, based on parts of the Intervention Mapping (IM protocol. Assessment of employees needs was done by combining results of face-to-face interviews, a questionnaire and focus group interviews. A set of theoretical methods and practical strategies were selected which resulted in an intervention program consisting of Group Motivational Interviewing (GMI supported by a social media platform, and environmental modifications. The Be Active & Relax program will be evaluated in a modified 2 X 2 factorial design. The environmental modifications will be pre-stratified and GMI will be randomised on department level. The program will be evaluated, using 4 arms: (1 GMI and environmental modifications; (2 environmental modifications; (3 GMI; (4 no intervention (control group. Questionnaire data on the primary outcome (need for recovery and secondary outcomes (daily physical activity, sedentary behaviour, relaxation/detachment, work- and health-related factors will be gathered at baseline (T0, at 6 months (T1, and at 12 months (T2 follow-up. In addition, an economic and a process evaluation will be performed. Discussion Reducing the need for recovery is hypothesized to be beneficial for employees, employers and society. It is assumed that there will be a reduction in need for recovery after 6 months and 12 months in the intervention group, compared to the control group. Results are expected in 2013

Waste heat recovery from adiabatic diesel engines by exhaust-driven Brayton cycles

Science.gov (United States)

Khalifa, H. E.

1983-01-01

An evaluation of Bryton Bottoming Systems (BBS) as waste heat recovery devices for future adiabatic diesel engines in heavy duty trucks is presented. Parametric studies were performed to evaluate the influence of external and internal design parameters on BBS performance. Conceptual design and trade-off studies were undertaken to estimate the optimum configuration, size, and cost of major hardware components. The potential annual fuel savings of long-haul trucks equipped with BBS were estimated. The addition of a BBS to a turbocharged, nonaftercooled adiabatic engine would improve fuel economy by as much as 12%. In comparison with an aftercooled, turbocompound engine, the BBS-equipped turbocharged engine would offer a 4.4% fuel economy advantage. If installed in tandem with an aftercooled turbocompound engine, the BBS could effect a 7.2% fuel economy improvement. The cost of a mass-produced 38 Bhp BBS is estimated at about $6460 or 170/Bhp. Technical and economic barriers that hinder the commercial introduction of bottoming systems were identified. Related studies in the area of waste heat recovery from adiabatic diesel engines and NASA-CR-168255 (Steam Rankine) and CR-168256 (Organic Rankine).

Developing a Topographic Model to Predict the Northern Hardwood Forest Type within Carolina Northern Flying Squirrel (Glaucomys sabrinus coloratus Recovery Areas of the Southern Appalachians

Directory of Open Access Journals (Sweden)

Andrew Evans

2014-01-01

Full Text Available The northern hardwood forest type is an important habitat component for the endangered Carolina northern flying squirrel (CNFS; Glaucomys sabrinus coloratus for den sites and corridor habitats between boreo-montane conifer patches foraging areas. Our study related terrain data to presence of northern hardwood forest type in the recovery areas of CNFS in the southern Appalachian Mountains of western North Carolina, eastern Tennessee, and southwestern Virginia. We recorded overstory species composition and terrain variables at 338 points, to construct a robust, spatially predictive model. Terrain variables analyzed included elevation, aspect, slope gradient, site curvature, and topographic exposure. We used an information-theoretic approach to assess seven models based on associations noted in existing literature as well as an inclusive global model. Our results indicate that, on a regional scale, elevation, aspect, and topographic exposure index (TEI are significant predictors of the presence of the northern hardwood forest type in the southern Appalachians. Our elevation + TEI model was the best approximating model (the lowest AICc score for predicting northern hardwood forest type correctly classifying approximately 78% of our sample points. We then used these data to create region-wide predictive maps of the distribution of the northern hardwood forest type within CNFS recovery areas.

Study of fuel cell powerplant with heat recovery

Science.gov (United States)

King, J. M.; Grasso, A. P.; Clausi, J. V.

1975-01-01

It was shown that heat can be recovered from fuel cell power plants by replacing the air-cooled heat exchangers in present designs with units which transfer the heat to the integrated utility system. Energy availability for a 40-kW power plant was studied and showed that the total usable energy at rated power represents 84 percent of the fuel lower heating value. The effects of design variables on heat availability proved to be small. Design requirements were established for the heat recovery heat exchangers, including measurement of the characteristics of two candidate fuel cell coolants after exposure to fuel cell operating conditions. A heat exchanger test program was defined to assess fouling and other characteristics of fuel cell heat exchangers needed to confirm heat exchanger designs for heat recovery.

Enhanced Monitored Natural Recovery (EMNR) Case Studies Review

Science.gov (United States)

2009-05-01

trends in sediment toxicity in thin layer capped and natural recovery areas. • Evaluation of temporal trends in macroinvertebrate benthic community...Pacific biotreatment lagoon . The WW Area is contaminated with mercury originating from a chlor- alkali facility operated by Georgia-Pacific, phenolic

Marine protected area design patterns in the Mediterranean Sea: Implications for conservation.

Science.gov (United States)

Rodríguez-Rodríguez, D; Rodríguez, J; Blanco, J M; Abdul Malak, D

2016-09-15

Mediterranean marine protected area (MPA) design patterns regarding geographic distribution, size, spacing and shape were analysed as a proxy of the region's MPA's ecological effectiveness and a first step towards an ecologically coherent MPA network. Results for legally designated MPAs and ecologically functional MPAs accounting for overlaps are presented. Geographically, Mediterranean MPA area is very unevenly distributed, with four-fifths concentrated in just three countries of the north-western part of the basin. Average distance between functional MPAs lies within recommended ecological thresholds, which suggests adequate potential connectivity of the Mediterranean MPA system. Mediterranean designated MPAs are larger than MPAs worldwide on average, although they are generally smaller than international guidance suggests at different levels: ecoregion, country and designation category. On average, Mediterranean designated and functional MPAs have relatively high compactness, which makes them prone to spillover and adequate viability, and less vulnerable to edge effects. Copyright © 2016 Elsevier Ltd. All rights reserved.

Marine protected area design for Bahia Portete - La Guajira, Colombian Caribbean

International Nuclear Information System (INIS)

Gutierrez Moreno, Carolina; Alonso C, David; Segura Quintero, Carolina

2008-01-01

Using an ecorregional planning process for the selection of conservation priority sites in the Colombian Caribbean region and the qualification of ecological criteria, Bahia Portete was identified as a potential site for the establishment of a new Marine Protected Area (MPA). This bay encompass a great variety of marine and coastal ecosystems, including fish, planktonic, and benthic communities as well as species that in conjunction with the environmental features form an area of high heterogeneity and unique biodiversity in the province of La Guajira. The purpose of this research was to design the first MPA in the north of the Province through the evaluation of ecologic criteria, as well as proposed conservation and management objectives; setting up a management category within the existing National Protected Areas System (SINAP in Spanish). Therefore, based on secondary information and following the The five S framework, methodology design by The Nature Conservancy for site planning, five conservation objectives (OdC) of coarse-filter or habitats were identified: corals, sea grasses, sandy beaches, rocky coasts and mangroves ecosystems, and three OdC of fine filter: areas with presence of Crocodylus acutus, sea turtles feeding areas, and areas of birds congregation. A viability analysis was developed for each healthy object found within the area, thus reflecting the biodiversity health of the area. The analysis of criteria, viability and the definition of the management objectives for the area, allowed the election of National Natural Park as the most appropriate management category for the area. Based on a systematic process and with the use of the MARXAN (University of Queensland) Decision Support System (DSS), three no-take zones were identified, with which the protection of a minimum of 30% of the coverage area for each of the objects is guaranteed as the initial contribution to the internal zoning of the new MPA

Recovery from chemical, biological, and radiological incidents. Critical infrastructure and economic impact considerations

Energy Technology Data Exchange (ETDEWEB)

Franco, David Oliver [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Yang, Lynn I. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Hammer, Ann E. [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

2012-06-01

To restore regional lifeline services and economic activity as quickly as possible after a chemical, biological or radiological incident, emergency planners and managers will need to prioritize critical infrastructure across many sectors for restoration. In parallel, state and local governments will need to identify and implement measures to promote reoccupation and economy recovery in the region. This document provides guidance on predisaster planning for two of the National Disaster Recovery Framework Recovery Support Functions: Infrastructure Systems and Economic Recovery. It identifies key considerations for infrastructure restoration, outlines a process for prioritizing critical infrastructure for restoration, and identifies critical considerations for promoting regional economic recovery following a widearea disaster. Its goal is to equip members of the emergency preparedness community to systematically prioritize critical infrastructure for restoration, and to develop effective economic recovery plans in preparation for a widearea CBR disaster.

Z Plant source aggregate area management study report

International Nuclear Information System (INIS)

1992-10-01

The US Department of Energy (DOE) Hanford Site in Washington State is or into numerically designated operational areas including the 100, 200, 300, 400, 600, and 1100 Areas. The US Environmental Protection Agency (EPA), in November 1989, included the 200 Areas of the Hanford Site on the National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) of 1980. Inclusion on the NPL initiates the Remedial Investigation (RI) and Feasibility Study (FS) process for characterizing the nature and extent of contamination, assessing risks to human health and the environment, and selection of remedial actions. This report presents the insults of an aggregate area management study (AAMS) for the Z Plant Aggregate Area located m the 200 Areas. The study provides the basis for initiating RIIFS under CERCLA or under the Resource Conservation and Recovery Act (RCRA) Facility Investigations (RFI) and Corrective Measures Studies (CMS). This report also integrates RCRA treatment, storage, or disposed (TSD) closure activities with CERCLA and RCRA past-practice investigations

Life Support Systems: Oxygen Generation and Recovery

Data.gov (United States)

National Aeronautics and Space Administration — The Advanced Exploration Systems (AES) Life Support Systems project Oxygen Generation and Recovery technology development area encompasses several sub-tasks in an...

What are your priorities right now? Identifying service needs across recovery stages to inform service development.

Science.gov (United States)

Laudet, Alexandre B; White, William

2010-01-01

Substance use disorders (SUD) are, for many, chronic conditions that are typically associated with severe impairments in multiple areas of functioning. "Recovery" from SUD is, for most, a lengthy process; improvements in other areas of functioning do not necessarily follow the attainment of abstinence. The current SUD service model providing intense, short-term, symptom-focused services is ill-suited to address these issues. A recovery-oriented model of care is emerging, which provides coordinated recovery-support services using a chronic-care model of sustained recovery management. Information is needed about substance users' priorities, particularly persons in recovery who are not currently enrolled in treatment, to guide the development of recovery-oriented systems. As a first step in filling this gap, we present qualitative data on current life priorities among a sample of individuals that collectively represent successive recovery stages (N = 356). Findings suggest that many areas of functioning remain challenging long after abstinence is attained, most notably employment and education, family/social relations, and housing. Although the ranking of priorities changes somewhat across recovery stages, employment is consistently the second most important priority, behind working on one's recovery. Study limitations are noted, and the implications of findings for the development and evaluation of recovery-oriented services are discussed.

SRP engineering and design history, Vol III, 200 F and H Areas

International Nuclear Information System (INIS)

Banick, C.J.

2000-01-01

This volume combines the record of events relating to the development of design for both the 200-F and H Areas. Chronologically, the definition of plant facilities was first established for the 200-F Area. The second area, 200-H, was projected initially to be a supplementary plutonium separations facility. This history explains the differences in character and capacity of the manufacturing facilities in both areas as production requirements and experience with separations processes advanced

SRP engineering and design history, Vol III, 200 F and H Areas

Energy Technology Data Exchange (ETDEWEB)

Banick, C.J.

2000-04-17

This volume combines the record of events relating to the development of design for both the 200-F and H Areas. Chronologically, the definition of plant facilities was first established for the 200-F Area. The second area, 200-H, was projected initially to be a supplementary plutonium separations facility. This history explains the differences in character and capacity of the manufacturing facilities in both areas as production requirements and experience with separations processes advanced.

Aerial radiological survey of the area surrounding the UNC Recovery Systems Facility, Wood River Junction, Rhode Island

International Nuclear Information System (INIS)

Bluitt, C.M.

1981-05-01

An aerial radiological survey to measure terrestrial gamma radiation was carried out over the United Nuclear Corporation (UNC) Recovery Systems Facility located near Wood River Junction, Rhode Island. At the time of the survey (August 1979) materials were being processed at the facility. Gamma ray data were collected over a 3.28 km 2 area centered on the facility by flying north-south lines spaced 60 m apart. Processed data indicated that detected radioisotopes and their associated gamma ray exposure rates were consistent with those expected from normal background emitters, except directly over the UNC Facility. Average exposure rates 1 m above the ground, as calculated from the aerial data, are presented in the form of an isopleth map. No ground sample data were taken at the time of the aerial survey

Designing for Wide-Area Situation Awareness in Future Power Grid Operations

Science.gov (United States)

Tran, Fiona F.

Power grid operation uncertainty and complexity continue to increase with the rise of electricity market deregulation, renewable generation, and interconnectedness between multiple jurisdictions. Human operators need appropriate wide-area visualizations to help them monitor system status to ensure reliable operation of the interconnected power grid. We observed transmission operations at a control centre, conducted critical incident interviews, and led focus group sessions with operators. The results informed a Work Domain Analysis of power grid operations, which in turn informed an Ecological Interface Design concept for wide-area monitoring. I validated design concepts through tabletop discussions and a usability evaluation with operators, earning a mean System Usability Scale score of 77 out of 90. The design concepts aim to support an operator's complete and accurate understanding of the power grid state, which operators increasingly require due to the critical nature of power grid infrastructure and growing sources of system uncertainty.

Inventory and review of aquifer storage and recovery in southern Florida

Science.gov (United States)

Reese, Ronald S.

2002-01-01

highest recovery efficiency achieved per cycle was 84 percent for cycle 16 at the Boynton Beach site.Factors that could affect recovery of freshwater varied widely between sites. The thickness of the open storage zone at all sites ranged from 45 to 452 feet. For sites with the storage zone in the Upper Floridan aquifer, transmissivity based on tests of the storage zones ranged from 800 to 108,000 feet squared per day, leakance values indicated that confinement is not good in some areas, and the chloride concentration of ambient water ranged from 500 to 11,000 milligrams per liter.Based on review of four case studies and data from other sites, several hydrogeologic and design factors appear to be important to the performance of aquifer storage and recovery in the Floridan aquifer system. Performance is maximized when the storage zone is thin and located at the top of the Upper Floridan aquifer, and transmissivity and salinity of the storage zone are moderate (less than 30,000 feet squared per day and 3,000 milligrams per liter of chloride concentration, respectively). The structural setting at a site could also be important because of the potential for updip migration of a recharged freshwater bubble due to density contrast or loss of overlying confinement due to deformation.

Review of laser mega joule target area: Design and processes

International Nuclear Information System (INIS)

Geitzholz, M.; Lanternier, C.

2006-01-01

The Laser Mega Joule (LMJ) target area is currently designed to achieve ignition and significant fusion gain in laboratory. LMJ will be composed of 240 identical large 370 mm * 370 mm square laser beams. These beams will focus 2 mega-joules of energy at the wavelength of 351 nm on the center of an experiment chamber. Design studies for target equipment are well advanced, target chamber and target holder (concrete) works have already begun. A detailed overview of the target area equipment is presented: target chamber, frame, diagnostic inserter manipulator, final optic assembly, dual diagnostic and laser reference, non cryogenic target positioner. Recent technical and architectural choices are detailed including safety transfers and alignment processes (target, laser and diagnostic). All this target equipment allows us to optimize shot chrono-gram, from target metrology to the shot, including calibration process. (authors)

Customer retention: A theoretical perspective of service failure and service recovery in the hotel industry

Directory of Open Access Journals (Sweden)

D. J. Petzer

2006-12-01

Full Text Available Purpose: The purpose of this paper is to provide a theoretical perspective on customer retention activities associated with service failure management and service recovery as a means to retain customers in the hotel industry - and to improve the competitiveness of a hotel. The research is pursued with the following objectives in mind: To determine the customer retention activities involved in the service failure management needed by hotels to retain customers. To determine the customer retention activities associated with the service recovery that hotels might perform in order to retain customers. Design/methodology/approach: Secondary sources such as textbooks, scientific journals, and previous studies on the subject were used to obtain relevant background information. A literature search of secondary sources was conducted to elucidate questions and areas of enquiry that relate to the research. Findings: The theoretical perspectives on service failure management and service recovery provided in this paper suggest several customer retention activities that might be used by hotels in order to manage service failure and service recovery - and thus become more competitive. Implications: This paper suggests a number of approaches that hotel managers might take to improve service failure management and service recovery. Such activities could assist a hotel in determining where it is lacking and where to improve its performance in these areas. These activities could provide guidance to managers who are dealing with the day-to-day operations of a hotel. They might help to avoid service failures in the first place, and, secondly, to give ideas about service recovery if failures do occur. On a more strategic level, these activities could also assist managers to develop a general customer retention strategy that incorporates service failure management and service recovery. Originality/value: Service failure management and service recovery are viewed as

Ecosystem impacts of hypoxia: thresholds of hypoxia and pathways to recovery

International Nuclear Information System (INIS)

Steckbauer, A; Duarte, C M; Vaquer-Sunyer, R; Carstensen, J; Conley, D J

2011-01-01

Coastal hypoxia is increasing in the global coastal zone, where it is recognized as a major threat to biota. Managerial efforts to prevent hypoxia and achieve recovery of ecosystems already affected by hypoxia are largely based on nutrient reduction plans. However, these managerial efforts need to be informed by predictions on the thresholds of hypoxia (i.e. the oxygen levels required to conserve biodiversity) as well as the timescales for the recovery of ecosystems already affected by hypoxia. The thresholds for hypoxia in coastal ecosystems are higher than previously thought and are not static, but regulated by local and global processes, being particularly sensitive to warming. The examination of recovery processes in a number of coastal areas managed for reducing nutrient inputs and, thus, hypoxia (Northern Adriatic; Black Sea; Baltic Sea; Delaware Bay; and Danish Coastal Areas) reveals that recovery timescales following the return to normal oxygen conditions are much longer than those of loss following the onset of hypoxia, and typically involve decadal timescales. The extended lag time for ecosystem recovery from hypoxia results in non-linear pathways of recovery due to hysteresis and the shift in baselines, affecting the oxygen thresholds for hypoxia through time.

Resource recovery and recycling in OECD countries

Energy Technology Data Exchange (ETDEWEB)

MacNeil, J.W.

It was the importance of the economic issues relevant to resource recovery and re-use that prompted OECD to become involved in this general area, and the author proposes in this talk to describe the principal features of the three main approaches to waste management from an economic perspective. These approaches are reduction of waste generation (i.e. birth control) resource recovery and materials recycling or re-use (reincarnation). Most of OECD's work in this area to date has been on the third of these approaches with particular emphasis on the economics of recycling, so somewhat more attention will be devoted to it. Then some conclusions will be drawn concerning possible policy actions to encourage a rational approach to management of this resource.

Advanced Oil Recovery Technologies for Improved Recovery from Slope Basin Clastic Reservoirs, Nash Draw Brushy Canyon Pool, Eddy County, New Mexico

International Nuclear Information System (INIS)

Murphy, Mark B.

1999-01-01

The overall objective of this project is to demonstrate that a development program based on advanced reservoir management methods can significantly improve oil recovery at the Nash Draw Pool (NDP). The plan includes developing a control area using standard reservoir management techniques and comparing its performance to an area developed using advanced reservoir management methods. Specific goals are (1) to demonstrate that an advanced development drilling and pressure maintenance program can significantly improve oil recovery compared to existing technology applications and (2) to transfer these advanced methodologies to oil and gas producers in the Permian Basin and elsewhere throughout the U.S. oil and gas industry

Changing spousal roles and their effect on recovery in gamblers anonymous: GamAnon, social support, wives and husbands.

Science.gov (United States)

Ferentzy, Peter; Skinner, Wayne; Antze, Paul

2010-09-01

This paper examines changing spousal roles and their effects upon recovery in Gamblers Anonymous (GA). It is based upon a qualitative study designed to gage uniformity as well as variations in approaches to recovery in GA. Interviews were conducted with 39 GA members (26 men, 13 women; mean age 56.5 years). Though the study was based in the Toronto area, only 13 interviews involved participants from that region. Phone interviews were conducted with GA members from various regions of both Canada and the US. GamAnon, GA's sister fellowship, has been designed for anyone affected seriously by someone's gambling problem. In practice, GamAnon comprises mostly women--spouses of male GA members--who traditionally have taken a keen interest in the ways in which their husbands achieve and maintain abstinence from gambling. Changing spousal roles have led to fewer women joining GamAnon, as many opt instead to part with troubled spouses. As well, more women are attending GA than in the past, typically with husbands who are disinclined to join GamAnon. All of this has drastically altered how GA members pursue recovery. These changes and their implications are discussed.

Mechanical ventilation with heat recovery in cold climates

DEFF Research Database (Denmark)

Kragh, Jesper; Rose, Jørgen; Svendsen, Svend

2005-01-01

Building ventilation is necessary to achieve a healthy and comfortable indoor environment, but as energy prices continue to rise it is necessary to reduce the energy consumption. Using mechanical ventilation with heat recovery reduces the ventilation heat loss significantly, but in cold climates...... freezes to ice. The analysis of measurements from existing ventilation systems with heat recovery used in single-family houses in Denmark and a test of a standard heat recovery unit in the laboratory have clearly shown that this problem occurs when the outdoor temperature gets below approximately –5º......C. Due to the ice problem mechanical ventilation systems with heat recovery are often installed with an extra preheating system reducing the energy saving potential significantly. New designs of high efficient heat recovery units capable of continuously defrosting the ice without using extra energy...

Biomarkers of stroke recovery: Consensus-based core recommendations from the Stroke Recovery and Rehabilitation Roundtable.

Science.gov (United States)

Boyd, Lara A; Hayward, Kathryn S; Ward, Nick S; Stinear, Cathy M; Rosso, Charlotte; Fisher, Rebecca J; Carter, Alexandre R; Leff, Alex P; Copland, David A; Carey, Leeanne M; Cohen, Leonardo G; Basso, D Michele; Maguire, Jane M; Cramer, Steven C

2017-07-01

The most difficult clinical questions in stroke rehabilitation are "What is this patient's potential for recovery?" and "What is the best rehabilitation strategy for this person, given her/his clinical profile?" Without answers to these questions, clinicians struggle to make decisions regarding the content and focus of therapy, and researchers design studies that inadvertently mix participants who have a high likelihood of responding with those who do not. Developing and implementing biomarkers that distinguish patient subgroups will help address these issues and unravel the factors important to the recovery process. The goal of the present paper is to provide a consensus statement regarding the current state of the evidence for stroke recovery biomarkers. Biomarkers of motor, somatosensory, cognitive and language domains across the recovery timeline post-stroke are considered; with focus on brain structure and function, and exclusion of blood markers and genetics. We provide evidence for biomarkers that are considered ready to be included in clinical trials, as well as others that are promising but not ready and so represent a developmental priority. We conclude with an example that illustrates the utility of biomarkers in recovery and rehabilitation research, demonstrating how the inclusion of a biomarker may enhance future clinical trials. In this way, we propose a way forward for when and where we can include biomarkers to advance the efficacy of the practice of, and research into, rehabilitation and recovery after stroke.

Off-design performance loss model for radial turbines with pivoting, variable-area stators

Science.gov (United States)

Meitner, P. L.; Glassman, A. J.

1980-01-01

An off-design performance loss model was developed for variable stator (pivoted vane), radial turbines through analytical modeling and experimental data analysis. Stator loss is determined by a viscous loss model; stator vane end-clearance leakage effects are determined by a clearance flow model. Rotor loss coefficient were obtained by analyzing the experimental data from a turbine rotor previously tested with six stators having throat areas from 20 to 144 percent of design area and were correlated with stator-to-rotor throat area ratio. An incidence loss model was selected to obtain best agreement with experimental results. Predicted turbine performance is compared with experimental results for the design rotor as well as with results for extended and cutback versions of the rotor. Sample calculations were made to show the effects of stator vane end-clearance leakage.

Enhanced styrene recovery from waste polystyrene pyrolysis using response surface methodology coupled with Box-Behnken design.

Science.gov (United States)

Mo, Yu; Zhao, Lei; Wang, Zhonghui; Chen, Chia-Lung; Tan, Giin-Yu Amy; Wang, Jing-Yuan

2014-04-01

A work applied response surface methodology coupled with Box-Behnken design (RSM-BBD) has been developed to enhance styrene recovery from waste polystyrene (WPS) through pyrolysis. The relationship between styrene yield and three selected operating parameters (i.e., temperature, heating rate, and carrier gas flow rate) was investigated. A second order polynomial equation was successfully built to describe the process and predict styrene yield under the study conditions. The factors identified as statistically significant to styrene production were: temperature, with a quadratic effect; heating rate, with a linear effect; carrier gas flow rate, with a quadratic effect; interaction between temperature and carrier gas flow rate; and interaction between heating rate and carrier gas flow rate. The optimum conditions for the current system were determined to be at a temperature range of 470-505°C, a heating rate of 40°C/min, and a carrier gas flow rate range of 115-140mL/min. Under such conditions, 64.52% WPS was recovered as styrene, which was 12% more than the highest reported yield for reactors of similar size. It is concluded that RSM-BBD is an effective approach for yield optimization of styrene recovery from WPS pyrolysis. Copyright © 2014 Elsevier Ltd. All rights reserved.

A system dynamics approach to develop a recovery model in the Malaysian automotive industry

Science.gov (United States)

Mohamad-Ali, N.; Ghazilla, R. A. R.; Abdul-Rashid, S. H.; Sakundarini, N.; Ahmad-Yazid, A.; Stephenie, L.

2017-06-01

Design strategies play a significant role to enhance recovery effectiveness at the end of product life cycle. By reviewing previous study, there are many factors involved to enhance recovery effectiveness but limited to linking design strategies factors in holistic and dynamics view. Proposed method are explained and an initial model for end-of-life vehicles (ELVs) recovery model illustrated in graphical and numerical data is presented. However this is limited to authors understanding and preliminary data which requires collaboration between designers and other stakeholders to develop a model based on actual situation.

Ward design: creating a healing patient-environment.

Science.gov (United States)

Biley, F

The drive for cost-effectiveness in hospital design over the decades has meant that minimal thought has been given to the effect of environments on patients' health. The author draws on research evidence to demonstrate how the appearance and ambience of patient areas can have profound effects on recovery patterns, and suggests that the creation of environments more conducive to healing need not incur heavy expense in time or money.

78 FR 69113 - Statutorily Mandated Designation of Difficult Development Areas for 2014

Science.gov (United States)

2013-11-18

... identical (to four decimal places) to the last area selected, and its inclusion resulted in only a minor... designated and on geographic definitions, contact Michael K. Hollar, Senior Economist, Economic Development..., 2000 Census, and Metropolitan Area Definitions Data from the 2010 Census on total population of...

Preliminary Design of the HiLumi-LHC Triplet Area Beam Screen

CERN Document Server

Kersevan, R; Kos, N

2014-01-01

The so-called beam screen (BS) is a proven solution for intercepting the thermal loads caused by the circulating beams in the cryogenically-cooled sections of the LHC and minimizing dynamic vacuum effects [1]. The new triplet area foreseen for the HiLumi-LHC (HL-LHC) machine upgrade [2] has the additional feature of needing internal tungsten shields to reduce the amount of collision debris which is deflected by the high-gradient triplet magnets towards the superconducting magnets' cold masses and coils. The very aggressive optics design, based on large beam separations, calls for a maximum of physical space to remain available to the counter rotating beams in the common BS. This places severe constraints to the fabrication and installation tolerances of the BS itself, in addition to affecting the design and routing of the cryogenic lines in the area. The latest version of the BS design will be shown and discussed, together with future plans for testing materials, fabrication procedures, and installation.

Chemical and Physical Soil Restoration in Mining Areas

Science.gov (United States)

Teresinha Gonçalves Bizuti, Denise; de Marchi Soares, Thaís; Roberti Alves de Almeida, Danilo; Sartorio, Simone Daniela; Casagrande, José Carlos; Santin Brancalion, Pedro Henrique

2017-04-01

The current trend of ecological restoration is to address the recovery of degraded areas by ecosystemic way, overcoming the rehabilitation process. In this sense, the topsoil and other complementary techniques in mining areas plays an important role in soil recovery. The aim of this study was to contextualize the soil improvement, with the use of topsoil through chemical and physical attributes, relative to secondary succession areas in restoration, as well as in reference ecosystems (natural forest). Eighteen areas were evaluated, six in forest restoration process, six native forests and six just mining areas. The areas were sampled in the depths of 0-5, 5-10, 10-20, 20-40 and 40-60 cm. Chemical indicators measured were parameters of soil fertility and texture, macroporosity, microporosity, density and total porosity as physical parameters. The forest restoration using topsoil was effective in triggering a process of soil recovery, promoting, in seven years, chemical and physical characteristics similar to those of the reference ecosystem.

The design and construction of large diameter pre-filter packed recovery wells at the Ninth Avenue Superfund Site

International Nuclear Information System (INIS)

Lombardo, S.L.; Maley, T.J.; Bono, B.A.

1992-01-01

Large diameter groundwater/oil recovery wells were installed in an unconfined sand aquifer at the Ninth Avenue Superfund Site in Gary, Indiana. To assure adequate filter packs, prefilter packed groundwater/oil recovery wells were selected to minimize silting by using appropriate screen slot size and filter pack. A properly sized filter pack was necessary to prevent the formation material from entering the well. During field drilling operations, open-quotes having sandsclose quotes and silting of existing wells were encountered. By using sieve analyses of the native aquifer soil, described by Driscoll (1989), the filter pack and screen slot size were selected. Prefilter packed well screens were selected for this site to assure the presence of a uniform filter pack, thus minimizing siltation in the wells. A prefilter packed well screen consists of a double screen with the interstitial space filled with granular filter pack material designed specifically for site conditions. These wells provide the adequate filter pack without the need to add additional filter pack material outside the well screen. Wells were installed using 12 1/4 inch ID hollow stem augers. This methodology is EPA-approved, expeditious, and inexpensive. Level B personal protective equipment was required during installation. Therefore, the advantages of hollow stem drilling include short drilling time and no circulation fluids. The 14 recovery wells were successfully installed in 14 days using the hollow stem auger drilling technique. Observations during well development revealed little or no silt present in purged groundwater

Optimal design of advanced distillation configuration for enhanced energy efficiency of waste solvent recovery process in semiconductor industry

International Nuclear Information System (INIS)

Chaniago, Yus Donald; Minh, Le Quang; Khan, Mohd Shariq; Koo, Kee-Kahb; Bahadori, Alireza; Lee, Moonyong

2015-01-01

Highlights: • Thermally coupled distillation process is proposed for waste solvent recovery. • A systematic optimization procedure is used to optimize distillation columns. • Response surface methodology is applied to optimal design of distillation column. • Proposed advanced distillation allows energy efficient waste solvent recovery. - Abstract: The semiconductor industry is one of the largest industries in the world. On the other hand, the huge amount of solvent used in the industry results in high production cost and potential environmental damage because most of the valuable chemicals discharged from the process are incinerated at high temperatures. A distillation process is used to recover waste solvent, reduce the production-related costs and protect the environment from the semiconductor industrial waste. Therefore, in this study, a distillation process was used to recover the valuable chemicals from semiconductor industry discharge, which otherwise would have been lost to the environment. The conventional sequence of distillation columns, which was optimized using the Box and sequential quadratic programming method for minimum energy objectives, was used. The energy demands of a distillation problem may have a substantial influence on the profitability of a process. A thermally coupled distillation and heat pump-assisted distillation sequence was implemented to further improve the distillation performance. Finally, a comparison was made between the conventional and advanced distillation sequences, and the optimal conditions for enhancing recovery were determined. The proposed advanced distillation configuration achieved a significant energy saving of 40.5% compared to the conventional column sequence

FoamVis, A Visualization System for Foam Research: Design and Implementation

OpenAIRE

Lipsa, Dan; Roberts, Richard; Laramee, Robert

2015-01-01

Liquid foams are used in areas such as mineral separation, oil recovery, food and beverage production, sanitation and fire fighting. To improve the quality of products and the efficiency of processes in these areas, foam scientists wish to understand and control foam behaviour. To this end, foam scientists have used foam simulations to model foam behaviour; however, analysing these simulations presents difficult challenges. We describe the main foam research challenges and present the design ...

Disaster Debris Recovery Database - Recovery

Data.gov (United States)

U.S. Environmental Protection Agency — The US EPA Disaster Debris Recovery Database (DDRD) promotes the proper recovery, recycling, and disposal of disaster debris for emergency responders at the federal,...

Sludge recovery apparatus

International Nuclear Information System (INIS)

Marmo, A.R.

1979-01-01

An improved design of a sludge recovery apparatus used in the fabrication of nuclear fuel is described. This apparatus provides for automatic separation of sludge from the grinder coolant, drying of the sludge into a flowable powder and transfer of the dry powder to a salvage container. It can be constructed to comply with criticality-safe-geometry requirements and to obviate need for operating personnel in its immediate vicinity. (UK)

High-intensity exercise and recovery during short-term ...

African Journals Online (AJOL)

Objective. To determine the effect of short-term creatine supplementation plus a protein-carbohydrate formula on high-intensity exercise performance and recovery. Design. A repeated-measures, experimental study, employing a randomised, double-blind, placebo-controlled, group comparison design was used.

Designing a Successful Transportation Project: Lessons Learned from the Clean Cities American Recovery and Reinvestment Act Projects

Energy Technology Data Exchange (ETDEWEB)

Kelly, K.; Singer, M.

2017-09-01

The largest source of funding for alternative fuel vehicle and infrastructure projects in the U.S. Department of Energy's Clean Cities program's history came from the American Recovery and Reinvestment Act (Recovery Act). In 2009, the 25 cost-share projects totaled nearly $300 million in federal government investment. This effort included the involvement of 50 Clean Cities coalitions and their nearly 700 stakeholder partners who provided an additional $500 million in matching funds to support projects in their local communities. In total, those 25 projects established 1,380 alternative fueling stations and put more than 9,000 alternative fuel and advanced technology vehicles on the road. Together, these projects displaced 154 million gasoline gallon equivalents (GGE) of petroleum and averted 254,000 tons of greenhouse gas (GHG) emissions, while supporting U.S. energy independence and contributing to regional economic development. During post-project interviews, project leaders consistently cited a number of key components - ranging from technical and logistical factors, to administrative capabilities - for accomplishing an effective and impactful project. This report summarizes the high-level project design and administrative considerations for conducting a successful transportation project.

Designing a Successful Transportation Project: Lessons Learned from the Clean Cities American Recovery and Reinvestment Act Projects

Energy Technology Data Exchange (ETDEWEB)

Kelly, Kay L. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Singer, Mark R. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-09-28

The largest source of funding for alternative fuel vehicle and infrastructure projects in the U.S. Department of Energy's Clean Cities program's history came from the American Recovery and Reinvestment Act (Recovery Act). In 2009, the 25 cost-share projects totaled nearly $300 million in federal government investment. This effort included the involvement of 50 Clean Cities coalitions and their nearly 700 stakeholder partners who provided an additional $500 million in matching funds to support projects in their local communities. In total, those 25 projects established 1,380 alternative fueling stations and put more than 9,000 alternative fuel and advanced technology vehicles on the road. Together, these projects displaced 154 million gasoline gallon equivalents (GGE) of petroleum and averted 254,000 tons of greenhouse gas (GHG) emissions, while supporting U.S. energy independence and contributing to regional economic development. During post-project interviews, project leaders consistently cited a number of key components - ranging from technical and logistical factors, to administrative capabilities - for accomplishing an effective and impactful project. This report summarizes the high-level project design and administrative considerations for conducting a successful transportation project.

Fast recovery strain measurements in a nuclear test environment

International Nuclear Information System (INIS)

Kitchen, W.R.; Nauman, W.J.; Vollmer, D.W.

1979-01-01

The recovery of early-time (50 μs or less) strain gage data on structural response experiments in underground nuclear tests has been a continuing problem for experimenters at the Nevada Test Site. Strain measurement is one of the primary techniques used to obtain experimental data for model verification and correlation with predicted effects. Peak strains generally occur within 50 to 100 μs of the radiation exposure. Associated with the exposure is an intense electromagnetic impulse that produces potentials of kilovolts and currents of kiloamperes on the experimental structures. For successful operation, the transducer and associated recording system must recover from the initial noise overload and accurately track the strain response within about 50 μs of the nuclear detonation. A gaging and fielding technique and a recording system design that together accomplish these objectives are described. Areas discussed include: (1) noise source model; (2) experimental cassette design, gage application, grounding, and shielding; (3) cable design and shielding between gage and recorder; (4) recorder design including signal conditioner/amplifier, digital encoder, buffer memory, and uphole data transmission; and (5) samples of experimental data

Safe Control for Spiral Recovery of Unmanned Aerial Vehicle

Directory of Open Access Journals (Sweden)

Chang-Jian Ru

2014-01-01

Full Text Available With unmanned aerial vehicles (UAVs widely used in both military and civilian fields, many events affecting their safe flying have emerged. That UAV’s entering into the spiral is such a typical safety issue. To solve this safety problem, a novel recovery control approach is proposed. First, the factors of spiral are analyzed. Then, based on control scheduling of state variables and nonlinear dynamic inversion control laws, the spiral recovery controller is designed to accomplish guidance and control of spiral recovery. Finally, the simulation results have illustrated that the proposed control method can ensure the UAV autonomous recovery from spiral effectively.

Design of mixer settler extraction cycles II for recovery uranium from phosphoric acid

International Nuclear Information System (INIS)

Abdul Jami; Hafni Lissa Nuri

2013-01-01

Mixer settler is technically designed for extraction and separation process of uranium from phosphoric acid solution. Design calculation results shows that: the mixer settler consists of two parts: part of extraction process in the mixer tank and part of separation process in settler tank. The mixer tank type of box with 4 baffles, the size of mixer tank, 0.8 m width, 0.8 m length, 1 m high of liquid, 1.05 m high of mixer tank, stirrer type of disk 6 blade, and power of mixing 4 hp and the settler tank type of rectangular with size of settler tank, 0.8 m width 5 m length, 1 m high of liquid, 1.05 m high of settler tank. For uranium recovery efficiency up to 91%, extraction process is done in 3 stage counter current flow using a solvent Organic (O) DEHPA-TOPO in Kerosene at a phase of ratio A/O of 2:1. The aqueous enter through stage 3 and the organic solvent enter through stage 1. The process of settling occurred with the value of settling velocity is 0.000694 m/s, dispersion factor Ψ = 0.3638 and the light fraction as the dispersed phase and value of Reynolds number (NRE) = 3,438. Because of the Reynolds number is lower than 5,000, it indicates that the quality of the separation is very good. (author)

Optimally efficient swimming in hyper-redundant mechanisms: control, design, and energy recovery

International Nuclear Information System (INIS)

Wiens, A J; Nahon, M

2012-01-01

Hyper-redundant mechanisms (HRMs), also known as snake-like robots, are highly adaptable during locomotion on land. Researchers are currently working to extend their capabilities to aquatic environments through biomimetic undulatory propulsion. In addition to increasing the versatility of the system, truly biomimetic swimming could also provide excellent locomotion efficiency. Unfortunately, the complexity of the system precludes the development of a functional solution to achieve this. To explore this problem, a rapid optimization process is used to generate efficient HRM swimming gaits. The low computational cost of the approach allows for multiple optimizations over a broad range of system conditions. By observing how these conditions affect optimal kinematics, a number of new insights are developed regarding undulatory swimming in robotic systems. Two key conditions are varied within the study, swimming speed and energy recovery. It is found that the swimmer mimics the speed control behaviour of natural fish and that energy recovery drastically increases the system's efficiency. Remarkably, this efficiency increase is accompanied by a distinct change in swimming kinematics. With energy recovery, the swimmer converges to a clearly anguilliform gait, without, it tends towards the carangiform mode. (paper)

A long-term soil structure observatory for post-compaction soil structure evolution: design and initial soil structure recovery observations

Science.gov (United States)

Keller, Thomas; Colombi, Tino; Ruiz, Siul; Grahm, Lina; Reiser, René; Rek, Jan; Oberholzer, Hans-Rudolf; Schymanski, Stanislaus; Walter, Achim; Or, Dani

2016-04-01

Soil compaction due to agricultural vehicular traffic alters the geometrical arrangement of soil constituents, thereby modifying mechanical properties and pore spaces that affect a range of soil hydro-ecological functions. The ecological and economic costs of soil compaction are dependent on the immediate impact on soil functions during the compaction event, and a function of the recovery time. In contrast to a wealth of soil compaction information, mechanisms and rates of soil structure recovery remain largely unknown. A long-term (>10-yr) soil structure observatory (SSO) was established in 2014 on a loamy soil in Zurich, Switzerland, to quantify rates and mechanisms of structure recovery of compacted arable soil under different post-compaction management treatments. We implemented three initial compaction treatments (using a two-axle agricultural vehicle with 8 Mg wheel load): compaction of the entire plot area (i.e. track-by-track), compaction in wheel tracks, and no compaction. After compaction, we implemented four post-compaction soil management systems: bare soil (BS), permanent grass (PG), crop rotation without mechanical loosening (NT), and crop rotation under conventional tillage (CT). BS and PG provide insights into uninterrupted natural processes of soil structure regeneration under reduced (BS) and normal biological activity (PG). The two cropping systems (NT and CT) enable insights into soil structure recovery under common agricultural practices with minimal (NT) and conventional mechanical soil disturbance (CT). Observations include periodic sampling and measurements of soil physical properties, earthworm abundance, crop measures, electrical resistivity and ground penetrating radar imaging, and continuous monitoring of state variables - soil moisture, temperature, CO2 and O2 concentrations, redox potential and oxygen diffusion rates - for which a network of sensors was installed at various depths (0-1 m). Initial compaction increased soil bulk density

Developing the philosophy of recovery in South African mental ...

African Journals Online (AJOL)

The recovery movement has emerged as an important and powerful force in the design and implementation of mental health care in many countries around the world. This involves new and more positive understandings of the concept of recovery, both as an individual outcome and as a goal of services. The basis for these ...

Development of infill drilling recovery models for carbonates reservoirs using neural networks and multivariate statistical as a novel method

International Nuclear Information System (INIS)

Soto, R; Wu, Ch. H; Bubela, A M

1999-01-01

This work introduces a novel methodology to improve reservoir characterization models. In this methodology we integrated multivariate statistical analyses, and neural network models for forecasting the infill drilling ultimate oil recovery from reservoirs in San Andres and Clearfork carbonate formations in west Texas. Development of the oil recovery forecast models help us to understand the relative importance of dominant reservoir characteristics and operational variables, reproduce recoveries for units included in the database, forecast recoveries for possible new units in similar geological setting, and make operational (infill drilling) decisions. The variety of applications demands the creation of multiple recovery forecast models. We have developed intelligent software (Soto, 1998), oilfield intelligence (01), as an engineering tool to improve the characterization of oil and gas reservoirs. 01 integrates neural networks and multivariate statistical analysis. It is composed of five main subsystems: data input, preprocessing, architecture design, graphic design, and inference engine modules. One of the challenges in this research was to identify the dominant and the optimum number of independent variables. The variables include porosity, permeability, water saturation, depth, area, net thickness, gross thickness, formation volume factor, pressure, viscosity, API gravity, number of wells in initial water flooding, number of wells for primary recovery, number of infill wells over the initial water flooding, PRUR, IWUR, and IDUR. Multivariate principal component analysis is used to identify the dominant and the optimum number of independent variables. We compared the results from neural network models with the non-parametric approach. The advantage of the non-parametric regression is that it is easy to use. The disadvantage is that it retains a large variance of forecast results for a particular data set. We also used neural network concepts to develop recovery

A Road Map to Canadian Chemical Recovery Handbook for Inhabited Areas: Scoping Study

Science.gov (United States)

2014-05-01

A Road Map to Canadian Chemical Recovery Handbook for I © Her Majesty the Queen in Right of Canada, as represented by the Minister of National...Australia (EMA) Office of Attorney General, Canberra. b) Australian Emergency Management Institute Mount Macedon, Victoria

B Plant source aggregate area management study report

International Nuclear Information System (INIS)

1993-03-01

The US Department of Energy (DOE) Hanford Site in Washington state is organized into numerically designated operational areas including the 100, 200, 300, 400, 600, and 100 Areas (Figure 1--1). The US Environmental Protection Agency (EPA), in November 1989, included the 200 Areas of the Hanford KLSite on the National Priorities List (NPL), included the 200 Areas of the Hanford Site on the National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation and Liability Act of Feasibility Study (FS) process for characterizing the nature and extent of contamination, assessing risks to human health and the environment, and selection of remedial actions. This report presents the results of an aggregate area management study (AIMS) for the B Plant Aggregate Area located in the 200 Areas. The study provides the basis for initiating RI/FS under CERCLA or under the Resource which contain reactor fuel processing and waste management Conservation and Recovery Act (RCRA) Facility Investigations (RFI) and Corrective Measures Studies (CMS). This report also integrates RCRA treatment, storage or disposal (TSD) closure activities with CERCLA and RCRA past-practice investigations

Significant intra-valvular pressure loss across EPIC SUPRA and perimount magna supra-annular designed aortic bioprostheses in patients with normal aortic size

Directory of Open Access Journals (Sweden)

Jagdish C. Mohan

2017-01-01

Full Text Available Doppler-derived trans-prosthetic gradients are higher and the estimated effective valve area is smaller than the catheter-derived and directly measured hemodynamic values, mostly due to pressure recovery phenomenon. Pressure recovery to a varying extent is common to all prosthetic heart valves including bioprostheses. Pressure recovery-related differences are usually small except in patients with bileaflet metallic prosthesis, wherein high-pressure local jets across central orifice have been documented since long back and also in patients with narrow aortic root. We describe two patients with normally functioning stented aortic bioprostheses with supra-annular design (EPIC SUPRA and PERIMOUNT MAGNA, wherein very high trans-prosthetic gradients and critically reduced estimated effective valve orifice areas in presence of normal aortic size were consistently recorded over long periods of follow-up. The valve leaflets, however had normal excursion, were thin, opened with a triangular or oblong shape and had expected geometric valve area (1.7 and 1.6 cm2 respectively measured by 3D trans-oesophageal echocardiographic planimetry. Pressure recovery upstream the valves accounted for 20% and 12% of total pressure gradients respectively. Dominant site for pressure drop was intra-valvular (75–85%. Such a phenomenon has not been reported in vivo for these two valve designs.

Significant intra-valvular pressure loss across EPIC SUPRA and perimount magna supra-annular designed aortic bioprostheses in patients with normal aortic size.

Science.gov (United States)

Mohan, Jagdish C; Mohan, Vishwas; Shukla, Madhu; Sethi, Arvind

Doppler-derived trans-prosthetic gradients are higher and the estimated effective valve area is smaller than the catheter-derived and directly measured hemodynamic values, mostly due to pressure recovery phenomenon. Pressure recovery to a varying extent is common to all prosthetic heart valves including bioprostheses. Pressure recovery-related differences are usually small except in patients with bileaflet metallic prosthesis, wherein high-pressure local jets across central orifice have been documented since long back and also in patients with narrow aortic root. We describe two patients with normally functioning stented aortic bioprostheses with supra-annular design (EPIC SUPRA and PERIMOUNT MAGNA), wherein very high trans-prosthetic gradients and critically reduced estimated effective valve orifice areas in presence of normal aortic size were consistently recorded over long periods of follow-up. The valve leaflets, however had normal excursion, were thin, opened with a triangular or oblong shape and had expected geometric valve area (1.7 and 1.6cm 2 respectively) measured by 3D trans-oesophageal echocardiographic planimetry. Pressure recovery upstream the valves accounted for 20% and 12% of total pressure gradients respectively. Dominant site for pressure drop was intra-valvular (75-85%). Such a phenomenon has not been reported in vivo for these two valve designs. Copyright © 2016. Published by Elsevier B.V.

Routine methods for post-transportation accident recovery of spent fuel casks

International Nuclear Information System (INIS)

Shappert, L.B.; Pope, R.B.; Best, R.E.; Jones, R.H.

1991-01-01

Spent fuel casks and other large radioactive material packages have been examined to determine whether the designs are adequate to allow the casks to be recovered using conventional recovery methods following a transportation accident. Casks and similar packages are typically designed with, and handled by, trunnions that support the package during transport. These trunnions are considered the best cask feature with which to grapple the cask once it is no longer in its usual shipping mode. Following a transport accident, the trunnions may be buried or entangled so that they are not readily accessible to initiate the recovery process. To evaluate the effectiveness of applying traditional recovery methods to spent fuel casks, a workshop was held in which a series of accidents involving casks were postulated; the modes of transportation considered included truck, rail, and barge. These participants knowledgeable in transport, handling, and, in some cases, recovery of large, heavy containers attended. Participants concluded that the physical recovery of a cask involved in an accident, irrespective of where the accident occurs, would be a straightforward rigging operation and that the addition of specific recovery features (e.g., additional trunnions) to the cask appears unnecessary

Development of a preprototype thermoelectric integrated membrane evaporation subsystem for water recovery

Science.gov (United States)

Winkler, H. E.; Roebelen, G. J., Jr.

1980-01-01

A three-man urine water recovery preprototype subsystem using a new concept to provide efficient potable water recovery from waste fluids on extended duration space flights has been designed, fabricated, and tested. Low power, compactness, and gravity insensitive operation are featured in this vacuum distillation subsystem that combines a hollow fiber polysulfone membrane evaporator with a thermoelectric heat pump. Application and integration of these key elements have solved problems inherent in previous reclamation subsystem designs. The hollow fiber elements provide positive liquid/gas phase control with no moving parts other than a waste liquid recirculation pump and a product water withdrawal pump. Tubular membranes provide structural integrity, improving on previous flat sheet membrane designs. A thermoelectric heat pump provides latent energy recovery.

Post-earthquake recovery in peripheral areas: the paradox of small municipalities’ reconstruction process in Abruzzo (Italy

Directory of Open Access Journals (Sweden)

Grazia Di Giovanni

2016-11-01

Full Text Available In 2009, Abruzzo Region was hit by a severe earthquake, which damaged the city of L’Aquila and other 56 minor municipalities already affected by trends of demographic and economic decline at the time of the disaster. This contribution focuses on the mid-term reconstruction of this “Seismic Crater” interpreted as a peculiar case in the scenario of Italian “inner areas”. The “National Strategy for Inner Areas” (SNAI was launched by the Italian Government in 2014 with the purpose of enhancing local development in peripheral fragile municipalities, distant from major service hubs. A large majority of the Crater is included in the list of inner areas. Special post-earthquake legislation and SNAI share multiple goals, especially related to supporting local revitalization. L’Aquila’s territory represents an “anomaly” in the milieu of inner areas: the disaster worsened pre-existing conditions of marginalisation, but post-earthquake reconstruction and related funds offered uncommon resources to shape transformative patterns of development, cooperation and innovation.Using a descriptive approach and focusing on purposes and contents of the Reconstruction Plans, the study questions the ongoing reconstruction process as an occasion to foster long-term socio-economic recovery, urban renewal, and innovative inter-municipal governance besides the rebuilding of urban fabrics in the light of SNAI.

Comprehensive analysis of area-specific and time-dependent changes in gene expression in the motor cortex of macaque monkeys during recovery from spinal cord injury.

Science.gov (United States)

Higo, Noriyuki; Sato, Akira; Yamamoto, Tatsuya; Oishi, Takao; Nishimura, Yukio; Murata, Yumi; Onoe, Hirotaka; Isa, Tadashi; Kojima, Toshio

2018-05-01

The present study aimed to assess the molecular bases of cortical compensatory mechanisms following spinal cord injury in primates. To accomplish this, comprehensive changes in gene expression were investigated in the bilateral primary motor cortex (M1), dorsal premotor cortex (PMd), and ventral premotor cortex (PMv) after a unilateral lesion of the lateral corticospinal tract (l-CST). At 2 weeks after the lesion, a large number of genes exhibited altered expression levels in the contralesional M1, which is directly linked to the lesioned l-CST. Gene ontology and network analyses indicated that these changes in gene expression are involved in the atrophy and plasticity changes observed in neurons. Orchestrated gene expression changes were present when behavioral recovery was attained 3 months after the lesion, particularly among the bilateral premotor areas, and a large number of these genes are involved in plasticity. Moreover, several genes abundantly expressed in M1 of intact monkeys were upregulated in both the PMd and PMv after the l-CST lesion. These area-specific and time-dependent changes in gene expression may underlie the molecular mechanisms of functional recovery following a lesion of the l-CST. © 2018 Wiley Periodicals, Inc.

State-Recovery Analysis of Spritz

DEFF Research Database (Denmark)

Ankele, Ralph; Kölbl, Stefan; Rechberger, Christian

2015-01-01

evidence that they may exist, the situation for Spritz is however not clear, as resistance against such attacks was not a design goal. In this paper, we provide the first cryptanalytic results on Spritz and introduce three different state recovery algorithms. Our first algorithm recovers an internal state...

A new vertical axis wind turbine design for urban areas

Science.gov (United States)

Frunzulica, Florin; Cismilianu, Alexandru; Boros, Alexandru; Dumitrache, Alexandru; Suatean, Bogdan

2016-06-01

In this paper we aim at developing the model of a Vertical Axis Wind Turbine (VAWT) with the short-term goal of physically realising this turbine to operate at a maximmum power of 5 kW. The turbine is designed for household users in the urban or rural areas and remote or isolated residential areas (hardly accsessible). The proposed model has a biplane configuration on each arm of the VAWT (3 × 2 = 6 blades), allowing for increased performance of the turbine at TSR between 2 and 2.5 (urban area operation) compared to the classic vertical axis turbines. Results that validate the proposed configuration as well as passive control methods to increase the performance of the classic VAWTs are presented.

Evaluating the utility and seasonality of NDVI values for assessing post-disturbance recovery in a subalpine forest.

Science.gov (United States)

Buma, Brian

2012-06-01

Forest disturbances around the world have the potential to alter forest type and cover, with impacts on diversity, carbon storage, and landscape composition. These disturbances, especially fire, are common and often large, making ground investigation of forest recovery difficult. Remote sensing offers a means to monitor forest recovery in real time, over the entire landscape. Typically, recovery monitoring via remote sensing consists of measuring vegetation indices (e.g., NDVI) or index-derived metrics, with the assumption that recovery in NDVI (for example) is a meaningful measure of ecosystem recovery. This study tests that assumption using MODIS 16-day imagery from 2000 to 2010 in the area of the Colorado's Routt National Forest Hinman burn (2002) and seedling density counts taken in the same area. Results indicate that NDVI is rarely correlated with forest recovery, and is dominated by annual and perennial forb cover, although topography complicates analysis. Utility of NDVI as a means to delineate areas of recovery or non-recovery are in doubt, as bootstrapped analysis indicates distinguishing power only slightly better than random. NDVI in revegetation analyses should carefully consider the ecology and seasonal patterns of the system in question.

Pacific Canada's Rockfish Conservation Areas: using Ostrom's design principles to assess management effectiveness

Directory of Open Access Journals (Sweden)

Darienne Lancaster

2015-09-01

Full Text Available International declines in marine biodiversity have lead to the creation of marine protected areas and fishery reserve systems. In Canada, 164 Rockfish Conservation Areas (RCAs were implemented between 2003 and 2007 and now cover 4847.2 km² of ocean. These reserves were created in response to widespread concern from fishers and nongovernmental organizations about inshore rockfish (genus Sebastes population declines. We used the design principles for effective common-pool resource management systems, originally developed by Elinor Ostrom, to assess the social and ecological effectiveness of these conservation areas more than 10 years after their initial implementation. We assessed the relative presence or absence of each design principle within current RCA management. We found that 2 of the 11 design principles were moderately present in the recreational fishery. All other design principles were lacking for the recreational sector. We found that 2 design principles were fully present and 5 were moderately present in the commercial sector. Four design principles were lacking in the commercial sector. Based on this analysis, we highlight 4 main areas for management improvement: (1 create an education and outreach campaign to explain RCA rules, regulations, boundaries, and the need for marine conservation; (2 increase monitoring of users and resources to discourage noncompliance and gather the necessary data to create social buy-in for marine conservation; (3 encourage informal nested governance through stakeholder organizations for education and self-regulation (e.g. fisher to fisher; and (4 most importantly, create a formal, decadal RCA review process to gather stakeholder input and make amendments to regulations and RCA boundaries. This information can be used to inform spatial management systems both in Canada and internationally. This analysis also contributes to a growing literature on effectively scaling up small-scale management techniques

Re-Defining Traditional Bazaar Areas and Shade Structures Via Parametric Design Methods

Directory of Open Access Journals (Sweden)

Ahmet Emre Dinçer

2017-12-01

Full Text Available For the continuation of life, people created various equipment and goods. To create mutual benefits, they’ve exchanged the overpruduced items with different products. This has begun the shopping act. By the increased amount of transactions, a need of defined area for shopping have arisen.  For a temporary time, trading areas have been developed at different locations at a certain period. In the course of time, beside trading, these areas served as socio-cultural spaces where the human relations were established. Moreover, demand of being able to immediately access to needed goods have emerged. This situation made having a permanent trading area essential. Therefore, enclosed and permanent trade areas from bazaar, inn, bedesten, arasta to shopping malls have emerged. Next to all these trading areas, traditional bazaar areas keep being established. Nowadays, there is a need of providing some determined comfort conditions to the users for these street alley bazaars. Decreasing the effect of unfavorable weather conditions and providing supportive certain services and units (like WCs, security, cleanliness, etc. are some of them. As a fundamental solution, without disengaging the user relations with the outside, shade structures are generally provided. Shade structures can support cleaning and similar jobs by gathering and using rainwater besides its purpose of protecting the user from bad weather conditions. Application examples of these systems are gradually increasing. However, it is necessary to develop new approaches, in order to stop these proposed shade structures, become prototypes and to adapt the proposal to its environment and to increase diversity. In this study, a convenient shade structure and its alternatives, which are adapted to environmental conditions, were designed to create a sample model for other bazaar areas. In models, basically, folding design approaches were pursued. For production of these shade structure models

End-of-life resource recovery from emerging electronic products

DEFF Research Database (Denmark)

Parajuly, Keshav; Habib, Komal; Cimpan, Ciprian

2016-01-01

Integrating product design with appropriate end-of-life (EoL) processing is widely recognized to have huge potentials in improving resource recovery from electronic products. In this study, we investigate both the product characteristics and EoL processing of robotic vacuum cleaner (RVC), as a case...... of emerging electronic product, in order to understand the recovery fate of different materials and its linkage to product design. Ten different brands of RVC were dismantled and their material composition and design profiles were studied. Another 125 RVCs (349 kg) were used for an experimental trial...... at a conventional ‘shred-and-separate’ type preprocessing plant in Denmark. A detailed material flow analysis was performed throughout the recycling chain. The results show a mismatch between product design and EoL processing, and the lack of practical implementation of ‘Design for EoL’ thinking. In the best...

Comparison of Cooling System Designs for an Exhaust Heat Recovery System Using an Organic Rankine Cycle on a Heavy Duty Truck

Directory of Open Access Journals (Sweden)

Nicolas Stanzel

2016-11-01

Full Text Available A complex simulation model of a heavy duty truck, including an Organic Rankine Cycle (ORC based waste heat recovery system and a vehicle cooling system, was applied to determine the system fuel economy potential in a typical drive cycle. Measures to increase the system performance were investigated and a comparison between two different cooling system designs was derived. The base design, which was realized on a Mercedes-Benz Actros vehicle revealed a fuel efficiency benefit of 2.6%, while a more complicated design would generate 3.1%. Furthermore, fully transient simulation results were performed and are compared to steady state simulation results. It is shown that steady state simulation can produce comparable results if averaged road data are used as boundary conditions.

Factors influencing recovery and restoration following a chemical incident.

Science.gov (United States)

Peña-Fernández, A; Wyke, S; Brooke, N; Duarte-Davidson, R

2014-11-01

Chemicals are an important part of our society. A wide range of chemicals are discharged into the environment every day from residential, commercial and industrial sources. Many of these discharges do not pose a threat to public health or the environment. However, global events have shown that chemical incidents or accidents can have severe consequences on human health, the environment and society. It is important that appropriate tools and technical guidance are available to ensure that a robust and efficient approach to developing a remediation strategy is adopted. The purpose of remediation is to protect human health from future exposure and to return the affected area back to normal as soon as possible. There are a range of recovery options (techniques or methods for remediation) that are applicable to a broad range of chemicals and incidents. Recovery options should be evaluated according to their appropriateness and efficacy for removing contaminants from the environment; however economic drivers and social and political considerations often influence decision makers on which remedial actions are implemented during the recovery phase of a chemical incident. To date, there is limited information in the literature on remediation strategies and recovery options that have been implemented following a chemical incident, or how successful they have been. Additional factors that can affect the approach taken for recovery are not well assessed or understood by decision makers involved in the remediation and restoration of the environment following a chemical incident. The identification of this gap has led to the development of the UK Recovery Handbook for Chemical Incidents to provide a framework for choosing an effective recovery strategy. A compendium of practical evidence-based recovery options (techniques or methods for remediation) for inhabited areas, food production systems and water environments has also been developed and is included in the chemical

Wide Area Recovery and Resiliency Program (WARRP) Interim Clearance Strategy for Environments Contaminated with Cesium-137

Science.gov (United States)

2012-07-01

recovery is both time and budget sensitive, it is imperative that the community address these values, and have agreement, before a disaster strikes. A key...agreement, before a disaster strikes. Pre-event clearance level concurrence is key to a community’s resiliency and speedy recovery. As such, technical and...Goiania) and those containing 137Cs and other radionuclides ( Chernobyl ). Another group contains documents relevant to site survey 3 procedures

Cost analysis and ecological benefits of environmental recovery methodologies in bauxite mining

OpenAIRE

Guimarães,João Carlos Costa; Barros,Dalmo Arantes de; Pereira,José Aldo Alves; Silva,Rossi Allan; Oliveira,Antonio Donizette de; Borges,Luís Antônio Coimbra

2013-01-01

This work analyzed and compared three methods of environmental recovery in bauxite mining commonly used in Poços de Caldas Plateau, MG, by means of recovery costs and ecological benefits. Earnings and costs data of environmental recovery activities were obtained for the areas that belonged to the Companhia Geral de Minas – CGM, on properties sited in the city of Poços de Caldas, MG. The amount of costs of these activities was used to compare the recovery methods by updating them monetarily to...

30 CFR 903.761 - Areas designated unsuitable for surface coal mining by act of Congress.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by act of Congress. 903.761 Section 903.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, applies to surface coal mining...

30 CFR 933.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by Act of Congress. 933.761 Section 933.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated Unsuitable for Coal Mining by Act of Congress, with...

Energy recovery in SUDS towards smart water grids: A case study

International Nuclear Information System (INIS)

Ramos, Helena M.; Teyssier, Charlotte; Samora, Irene; Schleiss, Anton J.

2013-01-01

The development of a methodology for urban flood adaptation and energy recovery solutions is resting on the concept of Sustainable Urban Drainage Systems (SUDS) as a measure to reduce risks of urban flooding while fully utilizing the available resources. Flood drainage systems are infrastructures essential in urban areas, which include retention ponds that can be used as water storage volumes to damp floods and simultaneously to produce energy, constituting innovative solutions to be integrated in future smart water grid′s designs. The consideration of urban flooding as a problem caused by excess water that can be harvested and re-used is expected to provide a comprehensive representation of a water-energy nexus for future urban areas. The study comprises an optimization of energy recovery in SUDS of a small district area of Lisbon down-town through the use of a low-head hydropower converter. The status-quo solution based on a basin catchment for the average expected runoff is analysed, with influence of the tidal backwater effect of the Atlantic Ocean which causes difficulties to the drainage of excess flow. The methodology used to reach the flow damping and the optimized solution for energy production is presented. -- Highlights: •An innovative solution for Sustainable Urban Drainage Systems (SUDS). •Use of retention ponds to reduce risks of urban flooding while producing energy. •Use of recently developed hydropower converters for low heads. •Solution to be integrated in future smart water networks for increasing efficiency. •Water and energy nexus for sustainable operation towards future smart cities

The Development of the Recovery Assessments by Phone Points (RAPP): A Mobile Phone App for Postoperative Recovery Monitoring and Assessment.

Science.gov (United States)

Jaensson, Maria; Dahlberg, Karuna; Eriksson, Mats; Grönlund, Åke; Nilsson, Ulrica

2015-09-11

In Sweden, day surgery is performed in almost 2 million patients per year. Patient satisfaction is closely related to potential adverse events during the recovery process. A way to empower patients and give them the opportunity to affect care delivery is to let them evaluate their recovery process. The most common evaluation method is a follow-up telephone call by a nurse one or two days after surgery. In recent years, mHealth apps have been used to evaluate the nurse-patient relationship for self-management in chronic diseases or to evaluate pain after surgery. To the best of our knowledge, no previous research has explored the recovery process after day surgery via mobile phone in a Swedish cohort. The objective of the study is to describe the process of developing a mobile phone app using a Swedish Web-based Quality of Recovery (SwQoR) questionnaire to evaluate postoperative recovery after day surgery. The development process included five steps: (1) setting up an interdisciplinary task force, (2) evaluating the potential needs of app users, (3) developing the Swedish Web version of a QoR questionnaire, (4) constructing a mobile phone app, and (5) evaluating the interface and design by staff working in a day-surgery department and patients undergoing day surgery. A task force including specialists in information and communication technology, eHealth, and nursing care worked closely together to develop a Web-based app. Modifications to the QoR questionnaire were inspired by instruments used in the field of recovery for both children and adults. The Web-based app, Recovery Assessment by Phone Points (RAPP) consists of two parts: (1) a mobile app installed on the patient's private mobile phone, and (2) an administrator interface for the researchers. The final version of the SwQoR questionnaire, which includes 31 items, was successfully installed in RAPP. The interface and the design were evaluated by asking for user opinions about the design and usefulness of the

Disaster recovery plan for Automation Technology

International Nuclear Information System (INIS)

Owens, M.J.

1997-06-01

Automation Technology provides a multitude of data processing and network services to the Environmental Restoration Contract (ERC). These services include: personal computers, local and wide area networks, and Internet and intranet support and services. ERC employees and client personnel receive these services primarily from the Data Center located on the ground floor in the Bechtel Corporate Center at 3350 George Washington Way, Richland, Washington. Centralized databases, server-based software, and network services for the Bechtel Local Area Network reside on servers located in the Data Center. The data communication circuits supported in this center allow for the transmission of business information to and from all project locations in the Hanford Site complex. The loss of one or more of these functions would seriously impact the ability of the ERC to conduct business and bring a virtual standstill to many ERC employees'' activities. Upon declaration of disaster by the Contingency Manager and the Disaster Recovery Coordinator, the disaster recovery plan will be implemented. 24 tabs

U Plant source aggregate area management study report

International Nuclear Information System (INIS)

1992-09-01

The US Department of Energy (DOE) Hanford Site in Washington State is organized into numerically designated operational areas including the 100, 200, 300, 400, 600, and 1100 Areas. The US Environmental Protection Agency (EPA), in November 1989, included the 200 Areas of the Hanford Site on the National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) of 1980. Inclusion on the NPL initiates the Remedial Investigation (RI) and Feasibility Study (FS) process for characterizing the nature and extent of contamination, assessing risks to human health and the environment, and selection of remedial actions. This report presents the results of an aggregate area management study (AAMS) for the U Plant Aggregate Area located in the 200 Areas. The study provides the basis for initiating RI/FS under CERCLA or under the Resource Conservation and Recovery Act (RCRA) Facility Investigations (RFI) and Corrective Measures Studies (CMS). This report also integrates RCRA treatment, storage, or disposal (TSD) closure activities with CERCLA and RCRA past-practice investigations

T Plant source aggregate area management study report

International Nuclear Information System (INIS)

1992-11-01

The US Department of Energy (DOE) Hanford Site in Washington State is organized into numerically designated operational areas including the 100, 200, 300, 400, 600, and 1100 Areas. The US Environmental Protection Agency (EPA), in November 1989, included the 200 Areas of the Hanford Site on the National Priorities List (NPL) under the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) of 1980. Inclusion on the NPL initiates the Remedial Investigation (RI) and Feasibility Study (FS) process for characterizing the nature and extent of contamination, assessing risks to human health and the environment, and selection of remedial actions. This report presents the results of an aggregate area management study (AAMS) for the T Plant Aggregate Area located in the 200 Areas. The study provides the basis for initiating RI/FS under CERCLA or under the Resource Conservation and Recovery Act (RCRA) Facility Investigations (RFI) and Corrective Measures Studies (CMS). This report also integrates RCRA treatment, storage, or disposal (TSD) closure activities with CERCLA and RCRA past-practice investigations

33 CFR 165.1405 - Regulated Navigation Areas and Security Zones; Designated Escorted Vessels-Philippine Sea and...

Science.gov (United States)

2010-07-01

...) PORTS AND WATERWAYS SAFETY REGULATED NAVIGATION AREAS AND LIMITED ACCESS AREAS Specific Regulated...). (a) Regulated navigation area. The following areas, designated by coordinates referencing World...

Progressing recovery-oriented care in psychiatric inpatient units: Occupational therapy’s role in supporting a stronger peer workforce

Directory of Open Access Journals (Sweden)

Chris Lloyd

2017-10-01

Full Text Available Purpose - Initiated by the service user movement, recovery-oriented practices are one of the keystones of modern mental health care. Over the past two decades, substantial gains have been made with introducing recovery-oriented practice in many areas of mental health practice, but there remain areas where progress is delayed, notably, the psychiatric inpatient environment. The peer support workforce can play a pivotal role in progressing recovery-oriented practices. The purpose of this paper is to provide a pragmatic consideration of how occupational therapists can influence mental health systems to work proactively with a peer workforce. Design/methodology/approach - The authors reviewed current literature and considered practical approaches to building a peer workforce in collaboration with occupational therapists. Findings - It is suggested that the peer support workforce should be consciously enhanced in the inpatient setting to support culture change as a matter of priority. Occupational therapists working on inpatient units should play a key role in promoting and supporting the growth in the peer support workforce. Doing so will enrich the Occupational Therapy profession as well as improving service user outcomes. Originality/value - This paper seeks to provide a pragmatic consideration of how occupational therapists can influence mental health systems to work proactively with a peer workforce.

30 CFR 942.761 - Areas designated unsuitable for surface coal mining by act of Congress.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by act of Congress. 942.761 Section 942.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining...

30 CFR 910.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by Act of Congress. 910.761 Section 910.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining...

30 CFR 937.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

Science.gov (United States)

2010-07-01

... mining by Act of Congress. 937.761 Section 937.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... WITHIN EACH STATE OREGON § 937.761 Areas designated unsuitable for surface coal mining by Act of Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining and...

30 CFR 921.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by Act of Congress. 921.761 Section 921.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining...

30 CFR 912.761 - Areas designated unsuitable for surface coal mining by act of Congress.

Science.gov (United States)

2010-07-01

... mining by act of Congress. 912.761 Section 912.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... WITHIN EACH STATE IDAHO § 912.761 Areas designated unsuitable for surface coal mining by act of Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining and...

30 CFR 947.761 - Areas designated unsuitable for surface coal mining by act of Congress.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by act of Congress. 947.761 Section 947.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining...

30 CFR 939.761 - Areas designated unsuitable for surface coal mining by Act of Congress.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by Act of Congress. 939.761 Section 939.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining...

30 CFR 941.761 - Areas designated unsuitable for surface coal mining by act of Congress.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by act of Congress. 941.761 Section 941.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining...

30 CFR 922.761 - Areas designated unsuitable for surface coal mining by act of Congress.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by act of Congress. 922.761 Section 922.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining...

30 CFR 905.761 - Areas designated unsuitable for surface coal mining by act of Congress.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Areas designated unsuitable for surface coal mining by act of Congress. 905.761 Section 905.761 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION... Congress. Part 761 of this chapter, Areas Designated by Act of Congress, shall apply to surface coal mining...

Design of absorption, regeneration and recovery system of low concentration hydrogen and tritium in He with titanium sponge

Energy Technology Data Exchange (ETDEWEB)

Fukuhara, M [Kawasaki Heavy Industries Ltd., Kobe (Japan)

1978-10-01

Design of a titanium sponge system to remove hydrogen from the helium coolant of high temperature gas-cooled reactors or fusion reactors is discussed in this paper. The data for the present purpose have been accumulated. The equilibrium relation of Ti-H/sub 2/ system was given by McQuillan. The present author of this paper obtained an absorption equilibrium diagram, and measurements were made for lower partial pressure than that of McQuillan's data. A breakthrough curve and an adsorption-desorption breakthrough curve of H/sub 2/-Ti sponge system, and the regeneration characteristics of the Ti sponge were measured. As the results of experiments, it is said that tritium and hydrogen can be removed with a Ti sponge system. Examples of the design of a practical system are presented. A disposable system was designed for OGL-1 under the principle that the used Ti sponge is a solid radioactive waste. A regenerative system was designed as a system, in which solid radioactive wastes are not produced. An example of a recovery system is also presented. Discussion on the reason why the Ti-sponge has not been used is presented.

Monitoring the recovery of a previously exploited surf-zone fish ...

African Journals Online (AJOL)

Limiting accessibility to a fishing area can reduce fishing effort effectively and may therefore promote local recovery of depleted stocks. In January 2002, beach driving was banned in South Africa, thereby reducing angler access to large areas of the coastline, particularly in less-developed areas. In November 2001 a project ...

78 FR 22501 - Designation of Areas for Air Quality Planning Purposes; State of Nevada; Total Suspended Particulate

Science.gov (United States)

2013-04-16

... Areas for Air Quality Planning Purposes; State of Nevada; Total Suspended Particulate AGENCY... designations for total suspended particulate within the State of Nevada because the designations are no longer necessary. These designations relate to the attainment or unclassifiable areas for total suspended...

Development of energy-efficient processes for natural gas liquids recovery

International Nuclear Information System (INIS)

Yoon, Sekwang; Binns, Michael; Park, Sangmin; Kim, Jin-Kuk

2017-01-01

A new NGL (natural gas liquids) recovery process configuration is proposed which can offer improved energy efficiency and hydrocarbon recovery. The new process configuration is an evolution of the conventional turboexpander processes with the introduction of a split stream transferring part of the feed to the demethanizer column. In this way additional heat recovery is possible which improves the energy efficiency of the process. To evaluate the new process configuration a number of different NGL recovery process configurations are optimized and compared using a process simulator linked interactively with external optimization methods. Process integration methodology is applied as part of the optimization to improve energy recovery during the optimization. Analysis of the new process configuration compared with conventional turbo-expander process designs demonstrates the benefits of the new process configuration. - Highlights: • Development of a new energy-efficient natural gas liquids recovery process. • Improving energy recovery with application of process integration techniques. • Considering multiple different structural changes lead to considerable energy savings.

Biosurfactants and their role in oil recovery

Energy Technology Data Exchange (ETDEWEB)

McInerney, Michael J. [University of Oklahoma (United States)

2011-07-01

This paper presents the role of biosurfactants in oil recovery. Types of biosurfactants include, among others, lipopeptides, rhamnolipids, sophorolipids. The process of oil recovery and the involvement of microbes are explained. The objective is to know if lipopeptide biosurfactants lower interfacial tension. Fatty acid composition is important for lipopeptide biosurfactant activity and microbial surfactants are hydrophilic and Interfacial Tension (IFT) values are high. Examples of biosurfactants with lower IFT values with mixtures are also given. An experiment was conducted to determine whether lipopeptides recovery entrapped oil or not. The procedure and experimental setup are shown. It is seen that with higher concentration of biosurfactants, the percentage of residual oil recovery is higher. Another experiment was conducted to see if biosurfactants greater than 40 mg/l can be produced in oil reservoirs. The experimental design and the analysis with the results are given. It was seen that more oil was produced. Conclusions from the study were, among other findings, that, in situ biosurfactant production and inoculation are possible.

Functional connectivity metrics during stroke recovery

DEFF Research Database (Denmark)

Yourganov, Grigori; Schmah, Tanya; Small, Steven L.

2010-01-01

We explore functional connectivity in nine subjects measured with 1 5T fMRI-BOLD in a longitudinal study of recovery from unilateral stroke affecting the motor area (Small et al, 2002) We found that several measures of complexity of covariance matrices show strong correlations with behavioral mea...

Buddhist Approaches to Addiction Recovery

Directory of Open Access Journals (Sweden)

Paramabandhu Groves

2014-10-01

Full Text Available The Buddha recognized addiction problems and advised his followers accordingly, although this was not the primary focus of his teachings. Thailand and Japan, which have long-standing Buddhist traditions, have developed Buddhist influenced responses to addiction. With its emphasis on craving and attachment, an understanding of the workings of the mind, as well as practices to work with the mind, Buddhism lends itself as a rich resource to assist addiction recovery. The twelve step movement has been an impetus to making use of ideas and practices from Buddhism. In particular, mindfulness, has started to be used to support addiction recovery, with promising results. Exploration of other areas of Buddhism is beginning, and may provide additional benefit in the future.

Beach recovery after 2004 Indian Ocean tsunami from Phang-nga, Thailand

Science.gov (United States)

Choowong, Montri; Phantuwongraj, Sumet; Charoentitirat, Thasinee; Chutakositkanon, Vichai; Yumuang, Sombat; Charusiri, Punya

2009-03-01

The 2004 Indian Ocean tsunami devastated the coastal areas along the Andaman western coast of Thailand and left unique physical evidence of its impact, including the erosional landforms of the pre-tsunami topography. Here we show the results from monitoring the natural recovery of beach areas at Khuk Khak and Bang Niang tidal channels of Khao Lak area, Phang-nga, Thailand. A series of satellite images before and after the tsunami event was employed for calculating the beach area and locating the position of the changed shoreline. Field surveys to follow-up the development of the post-tsunami beach area were conducted from 2005 to 2007 and the yearly beach profile was measured in 2006. As a result, the scoured beach areas where the tidal channel inlets were located underwent continuous recovery. The return of post-tsunami sediments within the beach zone was either achieved by normal wind and wave processes or during the storm surges in the rainy season. Post-2004 beach sediments were derived mainly from near offshore sources. The present situation of the beach zone has almost completed reversion back to the equilibrium stage and this has occurred within 2 years after the tsunami event. We suggest these results provide a better understanding of the geomorphological process involved in beach recovery after severe erosion such as by tsunami events.

Microbial enhanced oil recovery: Entering the log phase

Energy Technology Data Exchange (ETDEWEB)

Bryant, R.S.

1995-12-31

Microbial enhanced oil recovery (MEOR) technology has advanced internationally since 1980 from a laboratory-based evaluation of microbial processes to field applications. In order to adequately support the decline in oil production in certain areas, research on cost-effective technologies such as microbial enhanced oil recovery processes must focus on both near-term and long-term applications. Many marginal wells are desperately in need of an inexpensive improved oil recovery technology today that can assist producers in order to prevent their abandonment. Microbial enhanced waterflooding technology has also been shown to be an economically feasible technology in the United States. Complementary environmental research and development will also be required to address any potential environmental impacts of microbial processes. In 1995 at this conference, the goal is to further document and promote microbial processes for improved oil recovery and related technology for solving environmental problems.

A rigorous mechanistic model for predicting gas hydrate formation kinetics: The case of CO2 recovery and sequestration

International Nuclear Information System (INIS)

ZareNezhad, Bahman; Mottahedin, Mona

2012-01-01

Highlights: ► A mechanistic model for predicting gas hydrate formation kinetics is presented. ► A secondary nucleation rate model is proposed for the first time. ► Crystal–crystal collisions and crystal–impeller collisions are distinguished. ► Simultaneous determination of nucleation and growth kinetics are established. ► Important for design of gas hydrate based energy storage and CO 2 recovery systems. - Abstract: A rigorous mechanistic model for predicting gas hydrate formation crystallization kinetics is presented and the special case of CO 2 gas hydrate formation regarding CO 2 recovery and sequestration processes has been investigated by using the proposed model. A physical model for prediction of secondary nucleation rate is proposed for the first time and the formation rates of secondary nuclei by crystal–crystal collisions and crystal–impeller collisions are formulated. The objective functions for simultaneous determination of nucleation and growth kinetics are presented and a theoretical framework for predicting the dynamic behavior of gas hydrate formation is presented. Predicted time variations of CO 2 content, total number and surface area of produced hydrate crystals are in good agreement with the available experimental data. The proposed approach can have considerable application for design of gas hydrate converters regarding energy storage and CO 2 recovery processes.

Design analysis of a lead–lithium/supercritical CO2 Printed Circuit Heat Exchanger for primary power recovery

International Nuclear Information System (INIS)

Fernández, Iván; Sedano, Luis

2013-01-01

Highlights: • A design for a PbLi/CO 2 (SC) Printed Circuit Heat Exchanger which optimizes the pressure drop performance is proposed. • Numerical analyses have been performed to optimize the airfoil fins shape and arrangement. • SiC is proposed as structural material and tritium permeation barrier for the PCHE. • The integrated flux is larger than expected and allows reducing the CO 2 mass flow in this sector of the power cycle. • A transport model has been developed to evaluate the permeation of tritium from the liquid metal to the secondary CO 2 . -- Abstract: One of the key issues for fusion power plant technology is the efficient, reliable and safe recovery of the power extracted by the primary coolants. An interesting design option for power conversion cycles based on Dual Coolant Breeding Blankets (DCBB) is a Printed Circuit Heat Exchanger, which is supported by the advantages of its compactness, thermal effectiveness, high temperature and pressure capability and corrosion resistance. This work presents a design analysis of a silicon carbide Printed Circuit Heat Exchanger for lead–lithium/supercritical CO 2 at DEMO ranges (4× segmentation)

Recovery from schizophrenia and the recovery model.

Science.gov (United States)

Warner, Richard

2009-07-01

The recovery model refers to subjective experiences of optimism, empowerment and interpersonal support, and to a focus on collaborative treatment approaches, finding productive roles for user/consumers, peer support and reducing stigma. The model is influencing service development around the world. This review will assess whether optimism about outcome from serious mental illness and other tenets of the recovery model are borne out by recent research. Remission of symptoms has been precisely defined, but the definition of 'recovery' is a more diffuse concept that includes such factors as being productive and functioning independently. Recent research and a large, earlier body of data suggest that optimism about outcome from schizophrenia is justified. A substantial proportion of people with the illness will recover completely and many more will regain good social functioning. Outcome is better for people in the developing world. Mortality for people with schizophrenia is increasing but is lower in the developing world. Working appears to help people recover from schizophrenia, and recent advances in vocational rehabilitation have been shown to be effective in countries with differing economies and labor markets. A growing body of research supports the concept that empowerment is an important component of the recovery process. Key tenets of the recovery model - optimism about recovery from schizophrenia, the importance of access to employment and the value of empowerment of user/consumers in the recovery process - are supported by the scientific research. Attempts to reduce the internalized stigma of mental illness should enhance the recovery process.

Hydrogeology and Aquifer Storage and Recovery Performance in the Upper Floridan Aquifer, Southern Florida

Science.gov (United States)

Reese, Ronald S.; Alvarez-Zarikian, Carlos A.

2007-01-01

Well construction, hydraulic well test, ambient water-quality, and cycle test data were inventoried and compiled for 30 aquifer storage and recovery facilities constructed in the Floridan aquifer system in southern Florida. Most of the facilities are operated by local municipalities or counties in coastal areas, but five sites are currently being evaluated as part of the Comprehensive Everglades Restoration Plan. The relative performance of all sites with adequate cycle test data was determined, and compared with four hydrogeologic and design factors that may affect recovery efficiency. Testing or operational cycles include recharge, storage, and recovery periods that each last days or months. Cycle test data calculations were made including the potable water (chloride concentration of less than 250 milligrams per liter) recovery efficiency per cycle, total recovery efficiency per cycle, and cumulative potable water recovery efficiencies for all of the cycles at each site. The potable water recovery efficiency is the percentage of the total amount of potable water recharged for each cycle that is recovered; potable water recovery efficiency calculations (per cycle and cumulative) were the primary measures used to evaluate site performance in this study. Total recovery efficiency, which is the percent recovery at the end of each cycle, however, can be substantially higher and is the performance measure normally used in the operation of water-treatment plants. The Upper Floridan aquifer of the Floridan aquifer system currently is being used, or planned for use, at 29 of the aquifer storage and recovery sites. The Upper Floridan aquifer is continuous throughout southern Florida, and its overlying confinement is generally good; however, the aquifer contains brackish to saline ground water that can greatly affect freshwater storage and recovery due to dispersive mixing within the aquifer. The hydrogeology of the Upper Floridan varies in southern Florida; confinement

Design of Secure ECG-Based Biometric Authentication in Body Area Sensor Networks.

Science.gov (United States)

Peter, Steffen; Reddy, Bhanu Pratap; Momtaz, Farshad; Givargis, Tony

2016-04-22

Body area sensor networks (BANs) utilize wireless communicating sensor nodes attached to a human body for convenience, safety, and health applications. Physiological characteristics of the body, such as the heart rate or Electrocardiogram (ECG) signals, are promising means to simplify the setup process and to improve security of BANs. This paper describes the design and implementation steps required to realize an ECG-based authentication protocol to identify sensor nodes attached to the same human body. Therefore, the first part of the paper addresses the design of a body-area sensor system, including the hardware setup, analogue and digital signal processing, and required ECG feature detection techniques. A model-based design flow is applied, and strengths and limitations of each design step are discussed. Real-world measured data originating from the implemented sensor system are then used to set up and parametrize a novel physiological authentication protocol for BANs. The authentication protocol utilizes statistical properties of expected and detected deviations to limit the number of false positive and false negative authentication attempts. The result of the described holistic design effort is the first practical implementation of biometric authentication in BANs that reflects timing and data uncertainties in the physical and cyber parts of the system.

Design of Secure ECG-Based Biometric Authentication in Body Area Sensor Networks

Science.gov (United States)

Peter, Steffen; Pratap Reddy, Bhanu; Momtaz, Farshad; Givargis, Tony

2016-01-01

Body area sensor networks (BANs) utilize wireless communicating sensor nodes attached to a human body for convenience, safety, and health applications. Physiological characteristics of the body, such as the heart rate or Electrocardiogram (ECG) signals, are promising means to simplify the setup process and to improve security of BANs. This paper describes the design and implementation steps required to realize an ECG-based authentication protocol to identify sensor nodes attached to the same human body. Therefore, the first part of the paper addresses the design of a body-area sensor system, including the hardware setup, analogue and digital signal processing, and required ECG feature detection techniques. A model-based design flow is applied, and strengths and limitations of each design step are discussed. Real-world measured data originating from the implemented sensor system are then used to set up and parametrize a novel physiological authentication protocol for BANs. The authentication protocol utilizes statistical properties of expected and detected deviations to limit the number of false positive and false negative authentication attempts. The result of the described holistic design effort is the first practical implementation of biometric authentication in BANs that reflects timing and data uncertainties in the physical and cyber parts of the system. PMID:27110785

Design of Secure ECG-Based Biometric Authentication in Body Area Sensor Networks

Directory of Open Access Journals (Sweden)

Steffen Peter

2016-04-01

Full Text Available Body area sensor networks (BANs utilize wireless communicating sensor nodes attached to a human body for convenience, safety, and health applications. Physiological characteristics of the body, such as the heart rate or Electrocardiogram (ECG signals, are promising means to simplify the setup process and to improve security of BANs. This paper describes the design and implementation steps required to realize an ECG-based authentication protocol to identify sensor nodes attached to the same human body. Therefore, the first part of the paper addresses the design of a body-area sensor system, including the hardware setup, analogue and digital signal processing, and required ECG feature detection techniques. A model-based design flow is applied, and strengths and limitations of each design step are discussed. Real-world measured data originating from the implemented sensor system are then used to set up and parametrize a novel physiological authentication protocol for BANs. The authentication protocol utilizes statistical properties of expected and detected deviations to limit the number of false positive and false negative authentication attempts. The result of the described holistic design effort is the first practical implementation of biometric authentication in BANs that reflects timing and data uncertainties in the physical and cyber parts of the system.

76 FR 44613 - Designation of Eight Counties as High Intensity Drug Trafficking Areas

Science.gov (United States)

2011-07-26

... OFFICE OF NATIONAL DRUG CONTROL POLICY Designation of Eight Counties as High Intensity Drug Trafficking Areas AGENCY: Office of National Drug Control Policy. ACTION: Notice. SUMMARY: The Director of the Office of National Drug Control Policy has designated eight additional counties as High Intensity Drug...

Recovery from optic neuritis: an ROI-based analysis of LGN and visual cortical areas

DEFF Research Database (Denmark)

Korsholm, Kirsten; Madsen, Kristoffer Hougaard; Frederiksen, Jette L

2007-01-01

in the ROIs and compared activation during monocular stimulation of the affected and unaffected eye. In the acute phase the activation of LGN during visual stimulation of the affected eye was significantly reduced (P difference in LGN activation between...... the affected and unaffected eye diminished during recovery, and after 180 days the difference was no longer significant (P = 0.59). The decreased difference during recovery was mainly due to an increase in the fMRI signal when stimulating the affected eye, but included a component of a decreasing fMRI signal...... from LGN when stimulating the unaffected eye. In LOC, V1 and V2 activation during visual stimulation of the affected eye in the acute phase was significantly reduced (P difference diminished with no significant differences left after 180...

A qualitative exploration of Telling My Story in mental health recovery

OpenAIRE

Nurser, Kate

2017-01-01

Purpose: The aim of this thesis project is to explore the role of personal storytelling in mental health recovery. Design: The project is presented in portfolio format, including the following sections: a brief introduction to the portfolio, a systematic review of the literature on storytelling interventions for mental health recovery, an empirical paper exploring the qualitative experience of storytelling in a UK mental health recovery context, an extended methodology chapter, and an over...

The Recovery College: A unique service approach and qualitative evaluation.

Science.gov (United States)

Newman-Taylor, Katherine; Stone, Nicola; Valentine, Paul; Hooks, Zoe; Sault, Katherine

2016-06-01

This study examined the impact of a Recovery College, an educational service model focusing specifically on health care to engage people's hope, agency, and opportunities for recovery. For the purpose of the study, a qualitative approach was used given the absence of research in this area. Eleven people completed semistructured interviews conducted by an independent researcher. Verbatim transcripts were analyzed using thematic analysis. The analyses yielded themes emphasizing the impact of the organizational structure of the college. Coproduction of service delivery was contrasted with traditional provision and identified as fundamental to personal and professional changes made. Recovery College participants described clear gains. These findings are discussed in relation to the recovery literature and highlight the need for routine coproduction of services to facilitate recovery from the often devastating impact of mental ill-health. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Area balance and strain in an extensional fault system: Strategies for improved oil recovery in fractured chalk, Gilbertown Field, southwestern Alabama -- Year 2. Annual report, March 1997--March 1998

Energy Technology Data Exchange (ETDEWEB)

Pashin, J.C.; Raymond, D.E.; Rindsberg, A.K.; Alabi, G.G.; Carroll, R.E.

1998-09-01

Gilbertown Field is the oldest oil field in Alabama and has produced oil from fractured chalk of the Cretaceous Selma Group and glauconitic sandstone of the Eutaw Formation. Nearly all of Gilbertown Field is still in primary recovery, although waterflooding has been attempted locally. The objective of this project is to analyze the geologic structure and burial history of Mesozoic and Tertiary strata in Gilbertown Field and adjacent areas in order to suggest ways in which oil recovery can be improved. Indeed, the decline of oil production to marginally economic levels in recent years has made this type of analysis timely and practical. Key technical advancements being sought include understanding the relationship of requisite strain to production in Gilbertown reservoirs, incorporation of synsedimentary growth factors into models of area balance, quantification of the relationship between requisite strain and bed curvature, determination of the timing of hydrocarbon generation, and identification of the avenues and mechanisms of fluid transport.

Recovery Audit Contractor medical necessity readiness: one health system's journey.

Science.gov (United States)

Scott, Judith A; Camden, Mindy

2011-01-01

To develop a sustainable approach to Recovery Audit Contractor medical necessity readiness that mitigates the regulatory and financial risks of the organization. Acute care hospitals. Utilizing the model for improvement and plan-do-study-act methodology, this health system designed and implemented a medical necessity case management program. We focused on 3 areas for improvement: medical necessity review accuracy, review timeliness, and physician adviser participation for secondary reviews. Over several months, we improved accuracy and timeliness of our medical necessity reviews while also generating additional inpatient revenue for the health system. We successfully enhanced regulatory compliance and reduced our financial risks associated with Recovery Audit Contractor medical necessity audits. A successful medical necessity case management program can not only enhance regulatory compliance and reduce the amount of payments recouped by Medicare, but also generate additional inpatient revenue for your organization. With health care reform and accountable care organizations on the horizon, hospitals must find ways to protect and enhance revenue in order to carry out their missions. This is one way for case managers to help in that cause, to advocate for the care of their patients, and to bring value to the organization.

Recovery in psychosis: a Delphi study with experts by experience.

Science.gov (United States)

Law, Heather; Morrison, Anthony P

2014-11-01

This study aimed to establish consensus about the meaning of recovery among individuals with experience of psychosis. A Delphi approach was utilized to allow a large sample of service users to be anonymously consulted about their views on recovery. Service users were invited to take part in a 3-stage consultation process. A total of 381 participants gave their views on recovery in the main stage of this study, with 100 of these taking part in the final review stage. The final list of statements about recovery included 94 items, which were rated as essential or important by >80% of respondents. These statements covered items which define recovery, factors which help recovery, factors which hinder recovery, and factors which show that someone is recovering. As far as we are aware, it is the first study to identify areas of consensus in relation to definitions of recovery from a service user perspective, which are typically reported to be an idiosyncratic process. Implications and recommendations for clinical practice and future research are discussed. © The Author 2014. Published by Oxford University Press on behalf of the Maryland Psychiatric Research Center. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Recovery: old wine, flavor of the month or new organizing paradigm?

Science.gov (United States)

White, William L

2008-01-01

Recovery is emerging as an influential but ill-defined organizing concept for addiction treatment and the larger field of behavioral health care. The reification of the concept of recovery is discounted by some as nothing new ("We're already recovery oriented."), an ephemeral fad lacking substance and import ("This is old wine in a new wineskin."), or as hopelessly impractical ("Nobody will pay for it."). This essay uses historical analysis and treatment system performance data to argue that recovery is a revolutionary concept. Policymakers who are embracing this concept via the vision of a recovery-oriented system of care are, in spite of innumerable obstacles, radically altering the present design of addiction treatment.

Engineering studies of tritium recovery from CTR blankets and plasma exhaust

International Nuclear Information System (INIS)

Watson, J.S.

1975-01-01

Engineering studies on tritium handling problems in fusion reactors have included conceptual and experimental studies of techniques for recovery of tritium bred in the reactor blanket and conceptual designs for recovery and processing of tritium from plasma exhausts. The process requirements and promising techniques for the blanket system depend upon the materials used for the blanket, coolant, and structure and on the operating temperatures. Process requirements are likely to be set in some systems by allowable loss rates to the steam system or by inventory considerations. Conceptual studies have also been made for tritium handling equipment for fueling, recovery, and processing in plasma recycle systems of fusion reactors, and a specific design has been prepared for ''near-term'' Tokamak experiments. (auth)

Capabilities and modification plans for the Savannah River New Special Recovery facilities

International Nuclear Information System (INIS)

Gray, L.W.; Molen, G.F.; Lynn, J.M.

1986-01-01

The Savannah River New Special Recovery (NSR) facility is located in the 200-F Separations Area. This facility was designed and constructed to convert easily dissolvable plutonium oxides and metal from both onsite and offsite residues to plutonium nitrate-nitric acid solution. Capabilities were provided to purify a portion of the clarified dissolver solutions via anion exchange. The primary purification is provided by the 221-F canyon solvent extraction system. Minimal capacity was provided to handle slurries from poorly dissolving materials. The Actinide Technology Division of the Savannah River Laboratory is presently engaged in R and D to enhance both the solids throughput of the dissolvers and the feed clarification methods

Feasibility analysis of a small-scale ORC energy recovery system for vehicular application

International Nuclear Information System (INIS)

Capata, Roberto; Toro, Claudia

2014-01-01

Highlights: • We analyzed the feasibility of an “on-board” ORC recovery system to power auxiliaries. • Performance of the ORC cycle has been simulated with CAMEL-Pro™. • Several relevant ORC components have been designed. • Approximate characteristics dimensions of HRSG and evaporator have been calculated and a preliminary layout provided. • The evaluation of a possible assembling of the system has been developed. - Abstract: This paper analyses the feasibility of an “on-board” innovative and patented ORC recovery system. The vehicle thermal source can be either a typical diesel engine (1400 cc) or a small gas turbine set (15–30 kW). The sensible heat recovered from the exhaust gases feeds the energy recovery system that can produce sufficient extra power to sustain the conditioning system and other auxiliaries. The concept is suitable for all types of thermally propelled vehicles, but it is studied here for automotive applications. The characteristics of the organic cycle-based recovery system are discussed, and a preliminary design of the main components, such as the heat recovery exchanger, the evaporator and the pre-heater is presented. The main challenge are the imposed size and weight limitations that require a particular design for this compact recovery system. A possible system layout is analyzed and the requirements for a prototypal application are investigated

Recovery outcomes of schizophrenia patients treated with paliperidone palmitate in a community setting: patient and provider perspectives on recovery.

Science.gov (United States)

Williams, Wesley; McKinney, Christopher; Martinez, Larry; Benson, Carmela

2016-01-01

This study evaluated the effect of paliperidone palmitate long-acting injectable (LAI) antipsychotic on recovery-oriented mental health outcomes from the perspective of healthcare providers and patients during the treatment of patients with schizophrenia or schizoaffective disorders. Archival data for patients with a primary diagnosis of schizophrenia or schizoaffective disorder receiving ≥6 months of paliperidone palmitate LAI were retrieved from the electronic medical records system at the Mental Health Center of Denver. Mental health recovery was assessed from both a provider's (Recovery Markers Inventory [RMI]) and patient's (Consumer Recovery Measure [CRM]) perspective. A three-level hierarchical linear model (HLM) was utilized to determine changes in CRM and RMI scores by including independent variables in the models: intercept, months from treatment (slope), treatment time period (pretreatment and treatment), age, gender, primary diagnosis, substance abuse diagnosis, concurrent medications, and adherence to paliperidone palmitate LAI. A total of 219 patients were identified and included in the study. Results of the final three-level HLMs indicated an overall increase in CRM scores (p a retrospective, non-comparative design, and did not adjust for multiplicity Conclusions: The current study demonstrates that changes in recovery-oriented mental health outcomes can be detected following the administration of a specific antipsychotic treatment in persons with schizophrenia or schizoaffective disorders. Furthermore, patients receiving paliperidone palmitate LAI can effectively improve recovery-oriented outcomes, thereby supporting the drug's use as schizophrenia treatment from a recovery-oriented perspective.

Area balance and strain in an extensional fault system: Strategies for improved oil recovery in fractured chalk, Gilbertown Field, southwestern Alabama. Final report, March 1996--September 1998

Energy Technology Data Exchange (ETDEWEB)

Pashin, J.C.; Raymond, D.E.; Rindsberg, A.K.; Alabi, G.G.; Carroll, R.E.; Groshong, R.H.; Jin, G.

1998-12-01

This project was designed to analyze the structure of Mesozoic and Tertiary strata in Gilbertown Field and adjacent areas to suggest ways in which oil recovery can be improved. The Eutaw Formation comprises 7 major flow units and is dominated by low-resistivity, low-contrast play that is difficult to characterize quantitatively. Selma chalk produces strictly from fault-related fractures that were mineralized as warm fluid migrated from deep sources. Resistivity, dipmeter, and fracture identification logs corroborate that deformation is concentrated in the hanging-wall drag zones. New area balancing techniques were developed to characterize growth strata and confirm that strain is concentrated in hanging-wall drag zones. Curvature analysis indicates that the faults contain numerous fault bends that influence fracture distribution. Eutaw oil is produced strictly from footwall uplifts, whereas Selma oil is produced from fault-related fractures. Clay smear and mineralization may be significant trapping mechanisms in the Eutaw Formation. The critical seal for Selma reservoirs, by contrast, is where Tertiary clay in the hanging wall is juxtaposed with poorly fractured Selma chalk in the footwall. Gilbertown Field can be revitalized by infill drilling and recompletion of existing wells. Directional drilling may be a viable technique for recovering untapped oil from Selma chalk. Revitalization is now underway, and the first new production wells since 1985 are being drilled in the western part of the field.

Condensate recovery by cycling at declining pressures

Energy Technology Data Exchange (ETDEWEB)

Havlena, Z G; Griffith, J D; Pot, R; Kiel, O G

1967-06-05

Cycling condensate reservoirs under conditions of declining pressure, rather than constant pressure, is advantageous from both a recovery and an economic standpoint. Wet gas displaced from the swept areas is recovered concurrently with wet gas recovered by gas expansion from the unswept portions of the reservoir. Any liquid condensed in the swept areas is revaporized by dry injection gas and recovered as an enriched gas. By this mode of operation, high condensate recovery is obtained, gas sales may be possible at an earlier stage of depletion, more flexibility in field and plant operations is feasible and reduction of 15% in investment and operating costs is achieved. Injection gas requirements are reduced by 40%. The Windfall reservoir in Canada has been successfully produced in this manner, starting in 1962. It is a typical retrograde type reservoir which in 1965 represented 15% of reservoirs exploited in North America.

Parents' experiences managing their child's complicated postoperative recovery.

Science.gov (United States)

Purcell, Mary; Longard, Julie; Chorney, Jill; Hong, Paul

2018-03-01

Tonsillectomy is commonly performed as same-day surgery and parents are heavily relied upon for management of children's postoperative recovery. The objective of this study was to provide an in-depth description of the experiences parents face when managing their child's complicated postoperative recoveries at home. An exploratory qualitative study at an academic pediatric hospital in Eastern Canada was performed. Participants included 12 parents of children aged 3-6 years who underwent adeno/tonsillectomy and experienced unexpected outcomes or complications during the postoperative recovery period. Parents participated in semi-structured interviews within 6 months of their child's surgery. Interviews were transcribed verbatim and thematic analysis was used to identify themes in the parents' experiences. Parents described struggling to make the decision to come back to hospital, that adequate information does not prevent emotional difficulties, and feeling somewhat responsible for the unexpected outcome or complicated course of recovery. Communication with healthcare providers was considered very important in helping with the recovery process. This research helps to inform healthcare professionals about how they might better support families during complicated recovery processes. Areas of action may include clear communication, setting expectations, and psychosocial support. Copyright © 2018 Elsevier B.V. All rights reserved.

A low-rank matrix recovery approach for energy efficient EEG acquisition for a wireless body area network.

Science.gov (United States)

Majumdar, Angshul; Gogna, Anupriya; Ward, Rabab

2014-08-25

We address the problem of acquiring and transmitting EEG signals in Wireless Body Area Networks (WBAN) in an energy efficient fashion. In WBANs, the energy is consumed by three operations: sensing (sampling), processing and transmission. Previous studies only addressed the problem of reducing the transmission energy. For the first time, in this work, we propose a technique to reduce sensing and processing energy as well: this is achieved by randomly under-sampling the EEG signal. We depart from previous Compressed Sensing based approaches and formulate signal recovery (from under-sampled measurements) as a matrix completion problem. A new algorithm to solve the matrix completion problem is derived here. We test our proposed method and find that the reconstruction accuracy of our method is significantly better than state-of-the-art techniques; and we achieve this while saving sensing, processing and transmission energy. Simple power analysis shows that our proposed methodology consumes considerably less power compared to previous CS based techniques.

Mobile Launch Platform Vehicle Assembly Area (SWMU 056) Biosparge Expansion Interim Measures Work Plan

Science.gov (United States)

Burcham, Michael S.; Daprato, Rebecca C.

2016-01-01

This document presents the design details for an Interim Measure (IM) Work Plan (IMWP) for the Mobile Launch Platform/Vehicle Assembly Building (MLPV) Area, located at the John F. Kennedy Space Center (KSC), Florida. The MLPV Area has been designated Solid Waste Management Unit Number 056 (SWMU 056) under KSC's Resource Conservation and Recovery Act (RCRA) Corrective Action Program. This report was prepared by Geosyntec Consultants (Geosyntec) for the National Aeronautics and Space Administration (NASA) under contract number NNK09CA02B and NNK12CA13B, project control number ENV1642. The Advanced Data Package (ADP) presentation covering the elements of this IMWP report received KSC Remediation Team (KSCRT) approval at the December 2015 Team Meeting; the meeting minutes are included in Appendix A.

Molecular Design of Nanofiltration Membranes for the Recovery of Phosphorus from Sewage Sludge

KAUST Repository

Thong, Zhiwei

2016-08-24

With the rapid depletion of mineral phosphorus, the recovery of phosphorus from sewage sludge becomes increasingly important. However, the presence of various contaminants such as heavy metals in sewage sludge complicates the issue. One must separate phosphorus from the heavy metals in order to produce fertilizers of high quality. Among various available methods, nanofiltration (NF) has been demonstrated to be a feasible and promising option when the sewage sludge undergoes acidic dissolution and the operating pH is around 2. Because the performance of commercially available thin film composite (TFC) NF membranes reported thus far has great room for improvement, the development of highly permeable positively charged NF membranes is recommended. To this aim, a NF membrane that is desirable for phosphorus recovery was fabricated via interfacial polymerization of polyethylenimine (PEI) and trimesoyl chloride (TMC) on a porous poly(ether sulfone) (PES) membrane substrate. Through an optimization of the interfacial polymerization process, which involves varying the molecular weight of PEI and the concentration of TMC, the resultant membrane displays a low molecular weight cutoff (MWCO) of 170 Da with a reasonably high pure water permeability (A) of 6.4 LMH/bar. The newly developed NF membrane can effectively reject a wide variety of heavy metal ions such as Cu, Zn, Pb and Ni (>93%) while demonstrating a low phosphorus rejection of 19.6% at 10 bar using a feed solution of pH 2. Thus, up to 90% of the feed phosphorus may be recovered using this newly developed NF membrane at a permeate recovery of 90%. This is a highly competitive value for the recovery of phosphorus. © 2016 American Chemical Society.

Heat recovery unit operation of HVAC system in IMEF

International Nuclear Information System (INIS)

Paek, S. R.; Oh, Y. W.; Song, E. S.; Park, D. K.; Joo, Y. S.; Hong, K. P.

2003-01-01

HVAC system including a supply and exhaust air system in IMEF(Irradiated Materials Examination Facility) is an essential facility for preventing a leakage of radioactive materials and for a preservation of a working environment. It costs a lot to operate the HVAC system in IMEF because our ventilation type is once-through system, and an air flow is maintained from low level contamination area to high level and maintained high turns of ventilation air under certain conditions. As HRU(Heat Recovery Unit) at HVAC system based on PIEF(Post Irradiation Examination Facility) operation experiences is designed and adopted, it prevents from a heating coil freezing destruction in winter and makes much energy saving etc.. Heat pipe type HRU is adopted in IMEF, and a construction and operation result of HRU is examined

Design Considerations for Area-Constrained In-Pixel Photon Counting in Medipix3

CERN Document Server

Wong, W; Campbell, M; Heijne, E H M; Llopart, X; Tlustos, L

2008-01-01

Hybrid pixel detectors process impinging photons using front-end electronics electrically connected to a segmented sensor via solder bumps. This allows for complex in-pixel processing while maintaining 100% fill factor. Medipix3 is a single photon processing chip whose 55 μm x 55 μm pixels contain analog charge-processing circuits, inter-pixel routing, and digital blocks. While a standard digital design flow would use logic gates from a standard cell library, the integration of multiple functions and configurations within the compact area of the Medipix3 pixel requires a full-custom manual layout. This work describes the various area-saving design strategies which were employed to optimize the use of available space in the digital section of the Medipix3 pixel.

78 FR 59647 - Opportunity for Designation in Unassigned Areas of Southeast Texas

Science.gov (United States)

2013-09-27

...The Grain Inspection, Packers and Stockyards Administration (GIPSA) is asking persons or governmental agencies interested in providing official services in unassigned areas of Southeast Texas to submit an application for designation.

An implantable neurostimulator with an integrated high-voltage inductive power-recovery frontend

International Nuclear Information System (INIS)

Wang Yuan; Zhang Xu; Liu Ming; Li Peng; Chen Hongda

2014-01-01

This paper present a highly-integrated neurostimulator with an on-chip inductive power-recovery frontend and high-voltage stimulus generator. In particular, the power-recovery frontend includes a high-voltage full-wave rectifier (up to 100 V AC input), high-voltage series regulators (24/5 V outputs) and a linear regulator (1.8/3.3 V output) with bandgap voltage reference. With the high voltage output of the series regulator, the proposed neurostimulator could deliver a considerably large current in high electrode-tissue contact impedance. This neurostimulator has been fabricated in a CSMC 1 μm 5/40/700 V BCD process and the total silicon area including pads is 5.8 mm 2 . Preliminary tests are successful as the neurostimulator shows good stability under a 13.56 MHz AC supply. Compared to previously reported works, our design has advantages of a wide induced voltage range (26–100 V), high output voltage (up to 24 V) and high-level integration, which are suitable for implantable neurostimulators. (semiconductor integrated circuits)

Designing a strategic plan development approach for integrated area development projects

NARCIS (Netherlands)

de Kort, Inge

2009-01-01

Increasingly, it has become evident that spatial problems can no longer be resolved in isolation, but should be solved in conjunction with other development-related issues. Interest in integrated area development is growing, and a more integrated planning approach is desired. In this design-based

Mechanical ventilation with heat recovery in arctic climate

DEFF Research Database (Denmark)

Kragh, Jesper; Svendsen, Svend

2005-01-01

Mechanical ventilations systems with highly effective heat recovery units in arctic climate have problems with condensing water from the extracted humid indoor air. If the condensing water freezes to ice in the heat recovery unit, the airflow rate will quickly diminish due to the increasing...... pressure drop. Preheating the inlet air (outdoor air) to a temperature just above 0ºC is typically used to solve the problem. To minimize the energy cost, a more efficient solution to the problem is therefore desirable. In this project a new design of a heat recovery unit has been developed to the low......-energy house in Sisimiut, which is capable of continuously defrosting itself. The disadvantage of the unit is that it is quite big compared with other units. In this paper the new heat recovery unit is described and laboratory measurements are presented showing that the unit is capable of continuously...

Integrated funnel-and-gate/GZB product recovery technologies for in situ management of creosote NAPL-impacted aquifers

International Nuclear Information System (INIS)

Mueller, J.G.; Borchert, S.M.; Klingel, E.J.

1997-01-01

An in situ source management system was modeled and designed for the containment and recovery of creosote non-aqueous phase liquid (NAPL) at a former wood treating facility in Nashua, New Hampshire. The conceptual system was based on the integration of patented technologies for physical source containment and management (ie., funnel-and-gate technology) with patented in situ product recovery (i.e, GZB technology - described below). A funnel-and-gate physical barrier was proposed to mitigate the continued flow of NAPL into the Merrimack River. The purpose of the funnel was to divert groundwater (and potential NAPL) flow through two gate areas. Where required, an in situ system for product recovery was integrated. Mathematical modeling of the combined technologies led to the selection of a metal sheet pile barrier wall along 650 feet of the river's shoreline with the wall anchored into an underlying zone of lesser permeability. Multiple GZB wells were placed strategically within the system. This combination of technologies promised to offer a more effective, cost-efficient approach for long-term management of environmental concerns at Nashua, and related sites

Recovery in SoccerPart II—Recovery Strategies

OpenAIRE

Nedelec, Mathieu; McCall, Alan; Carling, Chris; Legall, Franck; Berthoin, Serge; Dupont, Grégory

2013-01-01

International audience; In the formerly published part I of this two-part review, we examined fatigue after soccer matchplay and recovery kinetics of physical performance, and cognitive, subjective and biological markers. To reduce the magnitude of fatigue and to accelerate the time to fully recover after completion, several recovery strategies are now used in professional soccer teams. During congested fixture schedules, recovery strategies are highly required to alleviate post-match fatigue...

PROPOSTA DE RECUPERAÇÃO DE UMA ÁREA DEGRADADA PELA ATIVIDADE DE EXTRAÇÃO DE BASALTO NO MUNICÍPIO DE CAÇADOR, SANTA CATARINA. / PROPOSAL OF RECOVERY OF AN AREA DEGRADED BY THE ACTIVITY OF EXTRACTION OF BASALT IN THE MUNICIPALITY OF CAÇADOR, SANTA CATARINA.

Directory of Open Access Journals (Sweden)

Roger Francisco Ferreira Campos

2017-08-01

Full Text Available The process of environmental degradation has increased due to the lack of environmental management of public and private companies. Among these environmental obstacles, the recovery of mineral extraction areas is one of the means that needs attention from environmental agencies, since many areas after Extraction is not recovered or degraded Area Recovery Plans are applied. Therefore, the present work has as objective to present a plant with the best means of disposition of environmental and social recovery of an area degraded by the extraction of basalt in the municipality of Caçador/SC. In order to carry out this study, it was analyzed visits in loco and in the surroundings to establish the best method of recovery of the area. This work presents a plan for a possible transformation of the degraded area through the extraction of basalt, through several procedures such as: Native species; In the transformation of the environment; civil constructions; aesthetic improvements, and other applicable methods, as has been happening recently in several quarries or degraded areas in Brazil and in the world. This will make the quarry a tourist and commercial spot, the disposition of the population of caçadorense and region, thus providing another place of entertainment and cultural activities.

Good job, bad job: The employment experiences of women in recovery from substance abuse.

Science.gov (United States)

Sinakhone, Joyce K; Hunter, Bronwyn A; Jason, Leonard A

2017-01-01

Women in metropolitan areas have lower employment participation and employment rates than men. Although women face multiple challenges in the labor market, those who have a history of substance use and are abstinent may have a greater disadvantage in obtaining viable employment opportunities due to factors associated with substance use. No research to date has examined employment experiences among women in recovery from substance use. This study examined employment characteristics and experiences of women who had a history of substance use and lived in sober-living environments in urban areas. Data were collected through telephone interviews to sober living homes that were located in 20 urban areas. Themes identified through thematic analysis included employment challenges, the importance of work to substance abuse recovery, job satisfaction, employment aspirations, and employment support in the sober living home. Employment is important to women in substance abuse recovery, not only as a means for financial support, but also as a life priority. The results highlight how employer scheduling practices, low-level positions, and lack of employment supports impact recovery. Findings provide insight into the need for employment support services, including employer education and flexible policies for women in recovery.

Weight Gain in Survivors Living in Temporary Housing in the Tsunami-Stricken Area during the Recovery Phase following the Great East Japan Earthquake and Tsunami.

Science.gov (United States)

Takahashi, Shuko; Yonekura, Yuki; Sasaki, Ryohei; Yokoyama, Yukari; Tanno, Kozo; Sakata, Kiyomi; Ogawa, Akira; Kobayashi, Seichiro; Yamamoto, Taro

2016-01-01

Survivors who lost their homes in the Great East Japan Earthquake and Tsunami were forced to live in difficult conditions in temporary housing several months after the disaster. Body weights of survivors living in temporary housing for a long period might increase due to changes in their life style and psychosocial state during the medium-term and long-term recovery phases. The aim of this study was to determine whether there were differences between body weight changes of people living in temporary housing and those not living in temporary housing in a tsunami-stricken area during the medium-term and long-term recovery phases. Health check-ups were performed about 7 months after the disaster (in 2011) and about 18 months after the disaster (in 2012) for people living in a tsunami-stricken area (n = 6,601, mean age = 62.3 y). We compared the changes in body weight in people living in temporary housing (TH group, n = 2,002) and those not living in temporary housing (NTH group, n = 4,599) using a multiple linear regression model. While there was no significant difference between body weights in the TH and NTH groups in the 2011 survey, there was a significant difference between the mean changes in body weight in both sexes. We found that the changes in body weight were significantly greater in the TH group than in the NTH group in both sexes. The partial regression coefficients of mean change in body weight were +0.52 kg (P-value tsunami- stricken area had a significant increase in body weight.

Recovery from cannabis use disorders: Abstinence versus moderation and treatment-assisted recovery versus natural recovery.

Science.gov (United States)

Stea, Jonathan N; Yakovenko, Igor; Hodgins, David C

2015-09-01

The present study of recovery from cannabis use disorders was undertaken with 2 primary objectives that address gaps in the literature. The first objective was to provide an exploratory portrait of the recovery process from cannabis use disorders, comparing individuals who recovered naturally with those who were involved in treatment. The second objective was to explore systematically the similarities and differences between abstinence and moderation recoveries. Adults who have recovered from a cannabis use disorder were recruited in the community (N = 119). The abstinence and treatment-assisted participants exhibited higher levels of lifetime cannabis problem severity than the moderation and natural recovery participants, respectively. As well, cognitive factors were identified as the most useful strategies for recovery (e.g., thinking about benefits and negative consequences of cannabis), followed by behavioral factors (e.g., avoidance of triggers for use and high-risk situations). Findings lend further support to the effectiveness of cognitive, motivational, and behavioral strategies as helpful actions and maintenance factors involved in the recovery process. The findings also generally support the idea that cannabis use disorders lie on a continuum of problem severity, with moderation and natural recoveries more likely to occur at the lower end of the continuum and abstinence and treatment-assisted recoveries more likely to occur at the upper end. (c) 2015 APA, all rights reserved).

Cryogenic recovery analysis of forced flow supercritical helium cooled superconductors

International Nuclear Information System (INIS)

Lee, A.Y.

1977-08-01

A coupled heat conduction and fluid flow method of solution was presented for cryogenic stability analysis of cabled composite superconductors of large scale magnetic coils. The coils are cooled by forced flow supercritical helium in parallel flow channels. The coolant flow reduction in one of the channels during the spontaneous recovery transient, after the conductor undergoes a transition from superconducting to resistive, necessitates a parallel channel analysis. A way to simulate the parallel channel analysis is described to calculate the initial channel inlet flow rate required for recovery after a given amount of heat is deposited. The recovery capability of a NbTi plus copper composite superconductor design is analyzed and the results presented. If the hydraulics of the coolant flow is neglected in the recovery analysis, the recovery capability of the superconductor will be over-predicted

Recovery of agricultural nutrients from biorefineries.

Science.gov (United States)

Carey, Daniel E; Yang, Yu; McNamara, Patrick J; Mayer, Brooke K

2016-09-01

This review lays the foundation for why nutrient recovery must be a key consideration in design and operation of biorefineries and comprehensively reviews technologies that can be used to recover an array of nitrogen, phosphorus, and/or potassium-rich products of relevance to agricultural applications. Recovery of these products using combinations of physical, chemical, and biological operations will promote sustainability at biorefineries by converting low-value biomass (particularly waste material) into a portfolio of higher-value products. These products can include a natural partnering of traditional biorefinery outputs such as biofuels and chemicals together with nutrient-rich fertilizers. Nutrient recovery not only adds an additional marketable biorefinery product, but also avoids the negative consequences of eutrophication, and helps to close anthropogenic nutrient cycles, thereby providing an alternative to current unsustainable approaches to fertilizer production, which are energy-intensive and reliant on nonrenewable natural resource extraction. Copyright © 2016 Elsevier Ltd. All rights reserved.

Expectation of recovery from low back pain

DEFF Research Database (Denmark)

Kongsted, Alice; Vach, Werner; Axø, Marie

2014-01-01

Study Design. A prospective cohort study conducted in general practice (GP) and chiropractic practice (CP).Objectives. To explore which patient characteristics were associated with recovery expectations in low back pain (LBP) patients, whether expectations predicted 3-month outcome, and to what...

An evaluation of service use outcomes in a Recovery College.

Science.gov (United States)

Bourne, Philippa; Meddings, Sara; Whittington, Adrian

2017-12-23

Recovery Colleges offer educational courses about recovery and mental health which are co-produced by mental health professionals and experts by lived experience. Previous evaluations have found positive effects of Recovery Colleges on a range of outcomes including wellbeing, recovery and quality of life. To evaluate service use outcomes for Sussex Recovery College students who use mental health services. The study used a controlled-before-and-after design. It used archival data to analyse service use before and after participants registered with the Recovery College (n = 463). Participants acted as their own control. Students used mental health services less after attending the Recovery College than before. Students who attended the Recovery College showed significant reductions in occupied hospital bed days, admissions, admissions under section and community contacts in the 18 months post compared with the 18 months before registering. Reductions in service use were greater for those who completed a course than those who registered but did not complete a course. These findings suggest that attending Recovery College courses is associated with reduced service use. The reductions equate to non-cashable cost-savings of £1200 per registered student and £1760 for students who completed a course. Further research is needed to investigate causality.

The innovative landscape design on the old dense area based on community participation

Science.gov (United States)

Soemardiono, B.; Rachmawati, M.

2018-03-01

Kembang Jepun area on the east side of the Kali Mas extends to the edge of the river. Along with the development of the city, Kembang Jepun denser, and these districts are facing some issues with limited landscape elements such as land and water elements, lacking in vegetation element in the settlement and services area, and non-optimal streetscape arrangement in the historic town and make the old city less attractive. In the other side, this historic section of the city has the great potential to be developed in order to support the economic developments of the city. Large Scale Intervention is the method of collaboration in developing area which possesses the meaning in the sustainable urban development. So community involvement is an important key factor in the design process and implementation as well as the type of participation and the technique of the process. The expected result of this paper is how to develop the innovative landscape design in the developing old dense area of Kembang Jepun based on community participation.

Mental health recovery: lived experience of consumers, carers and nurses.

Science.gov (United States)

Jacob, Sini; Munro, Ian; Taylor, Beverley Joan

2015-01-01

Background Mental health recovery is a prominent topic of discussion in the global mental health settings. The concept of mental health recovery brought about a major shift in the traditional philosophical views of many mental health systems. Aim The purpose of this article is to outline the results of a qualitative study on mental health recovery, which involved mental health consumers, carers and mental health nurses from an Area Mental Health Service in Victoria, Australia. This paper is Part One of the results that explored the meaning of recovery. Methods The study used van Manen's hermeneutic phenomenology to analyse the data. Findings Themes suggested that the cohort had varying views on recovery that were similar and dissimilar. The similar views were categorised under two processes involving the self, an internal process and an external process. These two processes involved reclaiming various aspects of oneself, living life, cure or absence of symptoms and contribution to community. The dissimilar views involved returning to pre-illness state and recovery was impossible. Conclusion This study highlights the need for placing importance on the person's sense of self in the recovery process.

On design of absorption, regeneration and recovery system of low concentration hydrogen and tritium in He with titanium sponge

International Nuclear Information System (INIS)

Fukuhara, Masashi

1978-01-01

Design of a titanium sponge system to remove hydrogen from the helium coolant of high temperature gas-cooled reactors or fusion reactors is discussed in this paper. The data for the present purpose have been accumulated. The equilibrium relation of Ti-H 2 system was given by McQuillan. The present author of this paper obtained an absorption equilibrium diagram, and measurements were made for lower partial pressure than that of McQuillan's data. A breakthrough curve and an adsorption-desorption breakthrough curve of H 2 -Ti sponge system, and the regeneration characteristics of the Ti sponge were measured. As the results of experiments, it is said that tritium and hydrogen can be removed with a Ti sponge system. Examples of the design of a practical system are presented. A disposable system was designed for OGL-1 under the principle that the used Ti sponge is a solid radioactive waste. A regenerative system was designed as a system, in which solid radioactive wastes are not produced. An example of a recovery system is also presented. Discussion on the reason why the Ti-sponge has not been used is presented. (Kato, T.)

Oxytetracycline recovery from aqueous media using computationally designed molecularly imprinted polymers.

Science.gov (United States)

Rodríguez-Dorado, Rosalía; Carro, Antonia M; Chianella, Iva; Karim, Kal; Concheiro, Angel; Lorenzo, Rosa A; Piletsky, Sergey; Alvarez-Lorenzo, Carmen

2016-09-01

Polymers for recovery/removal of the antimicrobial agent oxytetracycline (OTC) from aqueous media were developed with use of computational design and molecular imprinting. 2-Hydroxyethyl methacrylate, 2-acrylamide-2-methylpropane sulfonic acid (AMPS), and mixtures of the two were chosen according to their predicted affinity for OTC and evaluated as functional monomers in molecularly imprinted polymers and nonimprinted polymers. Two levels of AMPS were tested. After bulk polymerization, the polymers were crushed into particles (200-1000 μm). Pressurized liquid extraction was implemented for template removal with a low amount of methanol (less than 20 mL in each extraction) and a few extractions (12-18 for each polymer) in a short period (20 min per extraction). Particle size distribution, microporous structure, and capacity to rebind OTC from aqueous media were evaluated. Adsorption isotherms obtained from OTC solutions (30-110 mg L(-1)) revealed that the polymers prepared with AMPS had the highest affinity for OTC. The uptake capacity depended on the ionic strength as follows: purified water > saline solution (0.9 % NaCl) > seawater (3.5 % NaCl). Polymer particles containing AMPS as a functional monomer showed a remarkable ability to clean water contaminated with OTC. The usefulness of the stationary phase developed for molecularly imprinted solid-phase extraction was also demonstrated. Graphical Abstract Selection of functional monomers by molecular modeling renders polymer networks suitable for removal of pollutants from contaminated aqueous environments, under either dynamic or static conditions.

Individual Drilling Bit Design and Optimization in Mahu Area

Directory of Open Access Journals (Sweden)

Zhang Wenbo

2017-01-01

Full Text Available There are three sets of gravels in Mahu region. The gravels formation is characterized by high heterogeneity, high abrasiveness and poor drillability. It is so difficult to optimize bit that restrict seriously the overall exploration and development process. The compressive strength, internal friction angle, and drillability of the formation are tested to check the rock mechanical characteristic profile established by logging data. The individual bit design is carried out by the 3D simulation technology. A new PDC bit type is designed to form the drill bit series for Mahu area. Single PDC bit increases 90% of the drilling footage. The trip average footage is improved 3.45 times, the horizontal section average penetration increased 34.8%. The technical achievements have greatly improved economic development benefits of Mahu region by improving drilling speed and saving drilling costs.

From recovery values to recovery-oriented practice?

DEFF Research Database (Denmark)

Dalum, Helle; Pedersen, Inge Kryger; Cunningham, Harry

2015-01-01

Introduction: The recovery model has influenced mental health services and fostered new standards for best practice. However, knowledge about how mental health care professionals (HCPs) experience recoveryoriented programs is sparse. Aim/Question: This paper explores HCPs' experiences when...... facilitating a recovery-oriented rehabilitation program. The research question is howdo HCPs experience a change in their attitude and practicewhen applying recovery-oriented programs? Methods: This paper draws on semi-structured in-depth qualitative interviews conducted with 16 HCPs experienced...... in facilitating a recovery-oriented rehabilitation program in either the USA or Denmark. Results: Three themes emerged from the HCPs' reflections on changes in attitudes and practices: “Hopeful Attitude” captures a change in the HCPs' attitude toward a more positive view on the future for clients' living...

Coal fired steam generation for heavy oil recovery

International Nuclear Information System (INIS)

Firmin, K.

1992-01-01

In Alberta, some 21,000 m 3 /d of heavy oil and bitumen are produced by in-situ recovery methods involving steam injection. The steam generation requirement is met by standardized natural-gas-fired steam generators. While gas is in plentiful supply in Alberta and therefore competitively priced, significant gas price increases could occur in the future. A 1985 study investigating the alternatives to natural gas as a fuel for steam generation concluded that coal was the most economic alternative, as reserves of subbituminous coal are not only abundant in Alberta but also located relatively close to heavy oil and bitumen production areas. The environmental performance of coal is critical to its acceptance as an alternate fuel to natural gas, and proposed steam generator designs which could burn Alberta coal and control emissions satisfactorily are assessed. Considerations for ash removal, sulfur dioxide sorption, nitrogen oxides control, and particulate emission capture are also presented. A multi-stage slagging type of coal-fired combustor has been developed which is suitable for application with oilfield steam generators and is being commissioned for a demonstration project at the Cold Lake deposit. An economic study showed that the use of coal for steam generation in heavy oil in-situ projects in the Peace River and Cold Lake areas would be economic, compared to natural gas, at fuel price projections and design/cost premises for a project timing in the mid-1990s. 7 figs., 3 tabs

Teaching Health Center Graduate Medical Education Locations Predominantly Located in Federally Designated Underserved Areas.

Science.gov (United States)

Barclift, Songhai C; Brown, Elizabeth J; Finnegan, Sean C; Cohen, Elena R; Klink, Kathleen

2016-05-01

Background The Teaching Health Center Graduate Medical Education (THCGME) program is an Affordable Care Act funding initiative designed to expand primary care residency training in community-based ambulatory settings. Statute suggests, but does not require, training in underserved settings. Residents who train in underserved settings are more likely to go on to practice in similar settings, and graduates more often than not practice near where they have trained. Objective The objective of this study was to describe and quantify federally designated clinical continuity training sites of the THCGME program. Methods Geographic locations of the training sites were collected and characterized as Health Professional Shortage Area, Medically Underserved Area, Population, or rural areas, and were compared with the distribution of Centers for Medicare and Medicaid Services (CMS)-funded training positions. Results More than half of the teaching health centers (57%) are located in states that are in the 4 quintiles with the lowest CMS-funded resident-to-population ratio. Of the 109 training sites identified, more than 70% are located in federally designated high-need areas. Conclusions The THCGME program is a model that funds residency training in community-based ambulatory settings. Statute suggests, but does not explicitly require, that training take place in underserved settings. Because the majority of the 109 clinical training sites of the 60 funded programs in 2014-2015 are located in federally designated underserved locations, the THCGME program deserves further study as a model to improve primary care distribution into high-need communities.

An energy recovery electron linac-on-ring collider

International Nuclear Information System (INIS)

Merminga, L.; Krafft, G.A.; Lebedev, V.A.; Ben-Zvi, I.

2000-01-01

We present the design of high-luminosity electron-proton/ion colliders in which the electrons are produced by an Energy Recovering Linac (ERL). Electron-proton/ion colliders with center of mass energies between 14 GeV and 100 GeV (protons) or 63 GeV/A (ions) and luminosities at the 10 33 (per nucleon) level have been proposed recently as a means for studying hadronic structure. The linac-on-ring option presents significant advantages with respect to: (1) spin manipulations (2) reduction of the synchrotron radiation load in the detectors (3) a wide range of continuous energy variability. Rf power and beam dump considerations require that the electron linac recover the beam energy. Based on extrapolations from actual measurements and calculations, energy recovery is expected to be feasible at currents of a few hundred mA and multi-GeV energies. Luminosity projections for the linac-ring scenario based on fundamental limitations are presented. The feasibility of an energy recovery electron linac-on-proton ring collider is investigated and four conceptual point designs are shown corresponding to electron to proton energies of: 3 GeV on 15 GeV, 5 GeV on 50 GeV and 10 GeV on 250 GeV, and for gold ions with 100 GeV/A. The last two designs assume that the protons or ions are stored in the existing RHIC accelerator. Accelerator physics issues relevant to proton rings and energy recovery linacs are discussed and a list of required R and D for the realization of such a design is presented

Metazoan operons accelerate recovery from growth arrested states

Science.gov (United States)

Zaslaver, Alon; Baugh, L. Ryan; Sternberg, Paul W.

2011-01-01

Summary Existing theories explain why operons are advantageous in prokaryotes, but their occurrence in metazoans is an enigma. Nematode operon genes, typically consisting of growth genes, are significantly up-regulated during recovery from growth-arrested states. This expression pattern is anti-correlated to non-operon genes consistent with a competition for transcriptional resources. We find that transcriptional resources are initially limiting during recovery, and that recovering animals are highly sensitive to any additional decrease in transcriptional resources. Operons become advantageous because by clustering growth genes into operons, fewer promoters compete for the limited transcriptional machinery, effectively increasing the concentration of transcriptional resources, and accelerating recovery. Mathematical modeling reveals how a moderate increase in transcriptional resources can substantially enhance transcription rate and recovery. This design principle occurs in different nematodes and the chordate C. intestinalis. As transition from arrest to rapid growth is shared by many metazoans, operons could have evolved to facilitate these processes. PMID:21663799

Speech recovery device

Energy Technology Data Exchange (ETDEWEB)

Frankle, Christen M.

2004-04-20

There is provided an apparatus and method for assisting speech recovery in people with inability to speak due to aphasia, apraxia or another condition with similar effect. A hollow, rigid, thin-walled tube with semi-circular or semi-elliptical cut out shapes at each open end is positioned such that one end mates with the throat/voice box area of the neck of the assistor and the other end mates with the throat/voice box area of the assisted. The speaking person (assistor) makes sounds that produce standing wave vibrations at the same frequency in the vocal cords of the assisted person. Driving the assisted person's vocal cords with the assisted person being able to hear the correct tone enables the assisted person to speak by simply amplifying the vibration of membranes in their throat.

Speech recovery device

Energy Technology Data Exchange (ETDEWEB)

Frankle, Christen M.

2000-10-19

There is provided an apparatus and method for assisting speech recovery in people with inability to speak due to aphasia, apraxia or another condition with similar effect. A hollow, rigid, thin-walled tube with semi-circular or semi-elliptical cut out shapes at each open end is positioned such that one end mates with the throat/voice box area of the neck of the assistor and the other end mates with the throat/voice box area of the assisted. The speaking person (assistor) makes sounds that produce standing wave vibrations at the same frequency in the vocal cords of the assisted person. Driving the assisted person's vocal cords with the assisted person being able to hear the correct tone enables the assisted person to speak by simply amplifying the vibration of membranes in their throat.

Material control system design: Test Bed Nitrate Storage Area (TBNSA)

International Nuclear Information System (INIS)

Clark, G.A.; Da Roza, R.A.; Dunn, D.R.; Sacks, I.J.; Harrison, W.; Huebel, J.G.; Ross, W.N.; Salisbury, J.D.; Sanborn, R.H.; Weissenberger, S.

1978-05-01

This report provides an example of a hypothetical Special Nuclear Material (SNM) Safeguard Material Control and Accounting (MC and A) System which will be used as a subject for the demonstration of the Lawrence Livermore Laboratory MC and A System Evaluation Methodology in January 1978. This methodology is to become a tool in the NRC evaluation of license applicant submittals for Nuclear Fuel Cycle facilities. The starting point for this test bed design was the Allied-General Nuclear Services--Barnwell Nuclear Fuel Plant Reprocessing plant as described in the Final Safety Analysis Report (FSAR), of August 1975. The test bed design effort was limited to providing an SNM safeguard system for the plutonium nitrate storage area of this facility

Intraoperative and recovery room outcome | Edomwonyi | East ...

African Journals Online (AJOL)

Objectives: To identify and quantitate anaesthesia related complications in the intraoperative period and in the post anaesthesia recovery room. Design: A prospective study. Setting: University of Benin Teaching Hospital; a University - affiliated tertiary centre. Subjects: Patients scheduled for elective and emergency surgery ...

Improvement of Particle Recovery Method for Uranium Isotope Analysis Using SIMS

International Nuclear Information System (INIS)

Kim, Taehee; Park, Jinkyu; Lee, Chi-Gyu; Lim, Sang Ho; Han, Sun-Ho

2017-01-01

In this study, we developed a new design of vacuum-suction impactor with wider inlet nozzle and outlet nozzle for guiding particles to disperse the particles on the surface of carbon planchet. We prepared simulated samples with lead dioxide and examined particle recovery yield and degree of dispersion using the conventional vacuum impactor and the newly designed ones with different inlet nozzle diameters. We tried to improve the inlet part of vacuum impactor, in order to increase the recovery yield and disperse the collected particle on carbon planchet. As the diameter of inlet nozzle became larger, the collected particles were better dispersed on planchet. In addition, when the inner diameter of the impactor was 3 mm or 5 mm, the recovery yield was higher than that of conventional impactor. Considering the degree of dispersion and recovery yield, we used the impactor with 5 mm exit diameter and recovered the mixed uranium standard materials for SIMS measurement. We were able to reduce the mixing effect and measure the isotopic ratio more accurately and precisely.

Effectiveness of a multidisciplinary care program on recovery and return to work of patients after gynaecological surgery; design of a randomized controlled trial

Directory of Open Access Journals (Sweden)

Vonk Noordegraaf Antonie

2012-02-01

Full Text Available Abstract Background Return to work after gynaecological surgery takes much longer than expected, irrespective of the level of invasiveness. In order to empower patients in recovery and return to work, a multidisciplinary care program consisting of an e-health intervention and integrated care management including participatory workplace intervention was developed. Methods/Design We designed a randomized controlled trial to assess the effect of the multidisciplinary care program on full sustainable return to work in patients after gynaecological surgery, compared to usual clinical care. Two hundred twelve women (18-65 years old undergoing hysterectomy and/or laparoscopic adnexal surgery on benign indication in one of the 7 participating (university hospitals in the Netherlands are expected to take part in this study at baseline. The primary outcome measure is sick leave duration until full sustainable return to work and is measured by a monthly calendar of sickness absence during 26 weeks after surgery. Secondary outcome measures are the effect of the care program on general recovery, quality of life, pain intensity and complications, and are assessed using questionnaires at baseline, 2, 6, 12 and 26 weeks after surgery. Discussion The discrepancy between expected physical recovery and actual return to work after gynaecological surgery contributes to the relevance of this study. There is strong evidence that long periods of sick leave can result in work disability, poorer general health and increased risk of mental health problems. We expect that this multidisciplinary care program will improve peri-operative care, contribute to a faster return to work of patients after gynaecological surgery and, as a consequence, will reduce societal costs considerably. Trial registration Netherlands Trial Register (NTR: NTR2087

Hurricane Katrina: Fishing and Aquaculture Industries -- Damage and Recovery

National Research Council Canada - National Science Library

Buck, Eugene H

2005-01-01

.... In addition, inland areas account for much of the U.S. farmed catfish production. This report summarizes damage assessments and recovery efforts, with initial reports primarily anecdotal until more accurate assessments become available...

Area overhead analysis of SEF: A design methodology for tolerating SEU

International Nuclear Information System (INIS)

Blaquiere, Y.; Savaria, Y.

1987-01-01

Soft-Error filtering (SEF) is a design methodology proposed recently for implementing machines tolerant to SEU. This paper deals mainly with the evaluation and the reduction of the area overhead brought by SEF. A new shift register filtering latch configuration is proposed. The use of this latch, optimized for minimum area, reduces the area overhead by a factor of 2.6, when compared with latches optimized for time performance. A detailed analysis of the area overhead with SEF implemented on two relatively complex machines produced the following results: a SEF version of the 6800 microprocessor would require an area overhead varying between 12% and 69% depending on the SEF latch used and, a SEF version of the RISCII microprocessor would result in a 38.8% area overhead. An analysis of the cost of implementing the Hamming error correcting code on a register array is presented and this cost is compared with that of implementing SEU tolerance directly with SEF. Finally, a hybrid approach is proposed where a large register array is protected by an error correcting code whereas the isolated latches are replaced by filtering latches. This hybrid approach reduces the area overhead to 18.8% for the RISCII architecture

Design improvements to achieve ALARA exposures to plant personnel at Narora Atomic Power Station (NAPS)

International Nuclear Information System (INIS)

Mittal, S.; Mehta, H.C.; Roy, S.K.

2000-01-01

NAPS is the indigenously designed, constructed and commissioned, first PHWR station of standardized design for 220 MWe station of NPCIL. At NAPS, radiation fields started building up after first start up due to Cobalt-60 and this was a major concern, from collective dose point of view, for carrying out any activity specially around and with in the moderator system. Apart from this system, PHT and fueling machine areas are also vulnerable areas from radiation point of view. To reduce and control the high collective dose consumption, various design modifications; like moderator purification system modifications, changes in heavy water recovery arrangements and FT system, have been carried out at NAPS and these are discussed in this paper. (author)

Determining Factors for Fast Corneal Sensitivity Recovery After Pterygium Excision

OpenAIRE

Julio Morán, Gemma; Campos, Pamela; Pujol Vives, Pere; Munguia, Aitana; Mas Aixalà, Enric

2016-01-01

Purpose: To establish determining factors for fast corneal sensitivity (CS) recovery after pterygium excision. Methods: Thirty-two eyes of 14 males and 18 females with primary nasal pterygium were recruited. Differences in CS (in the 4 quadrants and the center using a Cochet–Bonnet esthesiometer), pterygium corneal area (PCA), tear osmolarity, tear break-up time, Schirmer test, and ocular symptoms were analyzed before and 1 month after lesion excision. The relationship between CS recovery...

Design of a Cryogenic Distillation Column for JET Water Detritiation System for Tritium Recovery

International Nuclear Information System (INIS)

Parracho, A.I.; Camp, P.; Dalgliesh, P.; Hollingsworth, A.; Lefebvre, X.; Lesnoj, S.; Sacks, R.; Shaw, R.; Smith, R.; Wakeling, B.

2015-01-01

A Water Detritiation System (WDS) is currently being designed and manufactured to be installed in the Active Gas Handling System (AGHS) of JET, currently the largest magnetic fusion experiment in the world. JET has been designed and built to study fusion operating conditions with the plasma fuelling done by means of a deuterium-tritium gas mixture. AGHS is a plant designed and built to safely process gas mixtures and impurities containing tritium recovered from the JET torus exhaust gases. Tritium is removed from these gas mixtures and recycled. Tritium depleted gases are sent to Exhaust Detritiation System (EDS) for final tritium removal prior to discharge into the environment. In EDS, tritium and tritiated species are catalytically oxidized into water, this tritiated water is then adsorbed onto molecular sieve beds (MSB). After saturation the MSBs are heated and the water is desorbed and collected for tritium recovery. The WDS facility is designed to recover tritium from water with an average activity of 1.9 GBq/l, and is able to process water with activities of 85 GBq/l and higher. Tritiated water is filtered and supplied to the electrolyser where the water is converted into gaseous oxygen and tritiated hydrogen. The hydrogen stream is first purified by selective diffusion through membranes of palladium alloy and then is fed to two cryogenic distillation columns (CD). These operate in parallel or in series depending on the water activity. In the CD columns, hydrogen isotopes containing tritium are recovered as the bottom product and hydrogen, the top product, is safely discarded to a stack. The CD columns are foreseen to have a throughput between 200 and 300 mole/h of hydrogen isotopes vapour and they operate at approximately ≈21.2K and 105 kPa. The design of the CD columns will be presented in this work. This work has been carried out within the framework of the Contract for the Operation of the JET Facilities and has received funding from the European Union�

Design of a uranium recovery pilot plant

International Nuclear Information System (INIS)

1984-01-01

The engineering design of a pilot plant of uranium recover, is presented. The diagrams and specifications of the equipments such as pipelines, pumps, values tanks, filters, engines, etc... as well as metallic structure and architetonic design is also presented. (author)

Satellite-Based Evaluation of the Post-Fire Recovery Process from the Worst Forest Fire Case in South Korea

Directory of Open Access Journals (Sweden)

Jae-Hyun Ryu

2018-06-01

Full Text Available The worst forest fire in South Korea occurred in April 2000 on the eastern coast. Forest recovery works were conducted until 2005, and the forest has been monitored since the fire. Remote sensing techniques have been used to detect the burned areas and to evaluate the recovery-time point of the post-fire processes during the past 18 years. We used three indices, Normalized Burn Ratio (NBR, Normalized Difference Vegetation Index (NDVI, and Gross Primary Production (GPP, to temporally monitor a burned area in terms of its moisture condition, vegetation biomass, and photosynthetic activity, respectively. The change of those three indices by forest recovery processes was relatively analyzed using an unburned reference area. The selected unburned area had similar characteristics to the burned area prior to the forest fire. The temporal patterns of NBR and NDVI, not only showed the forest recovery process as a result of forest management, but also statistically distinguished the recovery periods at the regions of low, moderate, and high fire severity. The NBR2.1 for all areas, calculated using 2.1 μm wavelengths, reached the unburned state in 2008. The NDVI for areas with low and moderate fire severity levels became significantly equal to the unburned state in 2009 (p > 0.05, but areas with high severity levels did not reach the unburned state until 2017. This indicated that the surface and vegetation moisture conditions recovered to the unburned state about 8 years after the fire event, while vegetation biomass and health required a longer time to recover, particularly for high severity regions. In the case of GPP, it rapidly recovered after about 3 years. Then, the steady increase in GPP surpassed the GPP of the reference area in 2015 because of the rapid growth and high photosynthetic activity of young forests. Therefore, the concluding scientific message is that, because the recovery-time point for each component of the forest ecosystem is

Butterfly Community Conservation Through Ecological Landscape Design in Urban Areas

Directory of Open Access Journals (Sweden)

Orsolya Borsai

2016-11-01

Full Text Available Due urbanization and extension of agricultural areas most of the ecosystems are strongly affected. As a result, preservation of biodiversity becomes more and more important aiming to reestablish the lost habitats of different species (mammals, birds, amphibians, insects, etc.. Our research focuses on butterflies which constitute an extremely important group of ‘model’ organisms. We have identified 12 diurnal ‘flying beauties’ specific to Cluj area (threatened and unthreathened species and investigated their ecological requirements that have to be provided for in any landscapes. Furthermore, based on the data colleted we have illustrated the utility of our approach by applying it to a hypothetical urban landscape (private garden following the traditional environmental guidelines in our landscape design.

Uses and abuses of recovery: implementing recovery-oriented practices in mental health systems

Science.gov (United States)

Slade, Mike; Amering, Michaela; Farkas, Marianne; Hamilton, Bridget; O'Hagan, Mary; Panther, Graham; Perkins, Rachel; Shepherd, Geoff; Tse, Samson; Whitley, Rob

2014-01-01

An understanding of recovery as a personal and subjective experience has emerged within mental health systems. This meaning of recovery now underpins mental health policy in many countries. Developing a focus on this type of recovery will involve transformation within mental health systems. Human systems do not easily transform. In this paper, we identify seven mis-uses (“abuses”) of the concept of recovery: recovery is the latest model; recovery does not apply to “my” patients; services can make people recover through effective treatment; compulsory detention and treatment aid recovery; a recovery orientation means closing services; recovery is about making people independent and normal; and contributing to society happens only after the person is recovered. We then identify ten empirically-validated interventions which support recovery, by targeting key recovery processes of connectedness, hope, identity, meaning and empowerment (the CHIME framework). The ten interventions are peer support workers, advance directives, wellness recovery action planning, illness management and recovery, REFOCUS, strengths model, recovery colleges or recovery education programs, individual placement and support, supported housing, and mental health trialogues. Finally, three scientific challenges are identified: broadening cultural understandings of recovery, implementing organizational transformation, and promoting citizenship. PMID:24497237

Recovery from PTSD following Hurricane Katrina.

Science.gov (United States)

McLaughlin, Katie A; Berglund, Patricia; Gruber, Michael J; Kessler, Ronald C; Sampson, Nancy A; Zaslavsky, Alan M

2011-06-01

We examined patterns and correlates of speed of recovery of estimated posttraumatic stress disorder (PTSD) among people who developed PTSD in the wake of Hurricane Katrina. A probability sample of prehurricane residents of areas affected by Hurricane Katrina was administered a telephone survey 7-19 months following the hurricane and again 24-27 months posthurricane. The baseline survey assessed PTSD using a validated screening scale and assessed a number of hypothesized predictors of PTSD recovery that included sociodemographics, prehurricane history of psychopathology, hurricane-related stressors, social support, and social competence. Exposure to posthurricane stressors and course of estimated PTSD were assessed in a follow-up interview. An estimated 17.1% of respondents had a history of estimated hurricane-related PTSD at baseline and 29.2% by the follow-up survey. Of the respondents who developed estimated hurricane-related PTSD, 39.0% recovered by the time of the follow-up survey with a mean duration of 16.5 months. Predictors of slow recovery included exposure to a life-threatening situation, hurricane-related housing adversity, and high income. Other sociodemographics, history of psychopathology, social support, social competence, and posthurricane stressors were unrelated to recovery from estimated PTSD. The majority of adults who developed estimated PTSD after Hurricane Katrina did not recover within 18-27 months. Delayed onset was common. Findings document the importance of initial trauma exposure severity in predicting course of illness and suggest that pre- and posttrauma factors typically associated with course of estimated PTSD did not influence recovery following Hurricane Katrina. © 2011 Wiley-Liss, Inc.

Recovery by imbibition from the lower Tamaulipas reservoir section A, Tamaulipas-Constituciones field

Energy Technology Data Exchange (ETDEWEB)

Gonzalez, O D; Teyssier S, J

1967-08-01

The Tamaulipas-Constituciones Field is situated about 27 km from the city and port of Tampico, Mex., and is a part of the N. district, of the N. Development Zone of Petroleos Mexicanos. This article describes a method designed to calculate the recovery of oil by means of the application of a secondary recovery process based on the phenomenon of imbibition. The flow in the reservoir follows a system of fractures which are interconnected both in series, parallel, and randomly distributed. A more adequate method of development was determined than that which was enforced when the area wells started their initial production. Applying this method, 2 programs were developed; the first for an operation pressure of 125 kg per sq cm and the second for an operation pressure of 100 kg per cm. The production history is graphically represented. The characteristics of the reservoir are described, including the rock properties and the reservoir fluids. Complete information is furnished on the entire operation by means of tabular data. (15 refs.)

Aquifer geochemistry at potential aquifer storage and recovery sites in coastal plain aquifers in the New York city area, USA

Science.gov (United States)

Brown, C.J.; Misut, P.E.

2010-01-01

The effects of injecting oxic water from the New York city (NYC) drinking-water supply and distribution system into a nearby anoxic coastal plain aquifer for later recovery during periods of water shortage (aquifer storage and recovery, or ASR) were simulated by a 3-dimensional, reactive-solute transport model. The Cretaceous aquifer system in the NYC area of New York and New Jersey, USA contains pyrite, goethite, locally occurring siderite, lignite, and locally varying amounts of dissolved Fe and salinity. Sediment from cores drilled on Staten Island and western Long Island had high extractable concentrations of Fe, Mn, and acid volatile sulfides (AVS) plus chromium-reducible sulfides (CRS) and low concentrations of As, Pb, Cd, Cr, Cu and U. Similarly, water samples from the Lloyd aquifer (Cretaceous) in western Long Island generally contained high concentrations of Fe and Mn and low concentrations of other trace elements such as As, Pb, Cd, Cr, Cu and U, all of which were below US Environmental Protection Agency (USEPA) and NY maximum contaminant levels (MCLs). In such aquifer settings, ASR operations can be complicated by the oxidative dissolution of pyrite, low pH, and high concentrations of dissolved Fe in extracted water.The simulated injection of buffered, oxic city water into a hypothetical ASR well increased the hydraulic head at the well, displaced the ambient groundwater, and formed a spheroid of injected water with lower concentrations of Fe, Mn and major ions in water surrounding the ASR well, than in ambient water. Both the dissolved O2 concentrations and the pH of water near the well generally increased in magnitude during the simulated 5-a injection phase. The resultant oxidation of Fe2+ and attendant precipitation of goethite during injection provided a substrate for sorption of dissolved Fe during the 8-a extraction phase. The baseline scenario with a low (0.001M) concentration of pyrite in aquifer sediments, indicated that nearly 190% more water

Neptunium immobilization and recovery using phase separated glasses

International Nuclear Information System (INIS)

Meaker, T.F.

1997-01-01

A phase separated (amorphous) glass has been developed which allows very efficient recovery of +4 valence actinides. The total amount of crystal formation in a heat treated vycor-type glass can be controlled with time, temperature and loading. Heat treatments at lower temperatures and for less time inhibit crystal formation while still allowing significant phase separation. If the Thorium loading exceeds 10 weight percent oxide, crystal formation during heat treatment may not be avoided. The total amount of crystal growth has a direct affect on thorium leachability. An increase in crystal formation limits the Th recovery significantly. High thorium loaded glasses (15 weight percent) with heat treatments (increased crystal formation) leach at approximately the same rate as non-heat treated glasses. A phase separated (amorphous) glass has been produced using thorium as a surrogate for neptunium. Two different homogeneous vycor compositions targeting 10 and 15 weight percent thorium oxide have been processed, heat treated and leached with concentrated nitric acid at 110 degrees C. Thorium recovery rates have been shown to be considerably better when the glass has been heat treated inducing phase separation that is relatively crystal free. Non-heat treated and crystalline (due to heat treatment) glasses have similar Th recovery rates with respect to surface area. Phase separated amorphous samples were found to have significantly higher thorium concentrations in the leachate compared to non-heat treated and crystalline glasses for all mesh sizes. All glasses had increased thorium concentration in the leachate as surface area increased

Resolution recovery for Compton camera using origin ensemble algorithm.

Science.gov (United States)

Andreyev, A; Celler, A; Ozsahin, I; Sitek, A

2016-08-01

Compton cameras (CCs) use electronic collimation to reconstruct the images of activity distribution. Although this approach can greatly improve imaging efficiency, due to complex geometry of the CC principle, image reconstruction with the standard iterative algorithms, such as ordered subset expectation maximization (OSEM), can be very time-consuming, even more so if resolution recovery (RR) is implemented. We have previously shown that the origin ensemble (OE) algorithm can be used for the reconstruction of the CC data. Here we propose a method of extending our OE algorithm to include RR. To validate the proposed algorithm we used Monte Carlo simulations of a CC composed of multiple layers of pixelated CZT detectors and designed for imaging small animals. A series of CC acquisitions of small hot spheres and the Derenzo phantom placed in air were simulated. Images obtained from (a) the exact data, (b) blurred data but reconstructed without resolution recovery, and (c) blurred and reconstructed with resolution recovery were compared. Furthermore, the reconstructed contrast-to-background ratios were investigated using the phantom with nine spheres placed in a hot background. Our simulations demonstrate that the proposed method allows for the recovery of the resolution loss that is due to imperfect accuracy of event detection. Additionally, tests of camera sensitivity corresponding to different detector configurations demonstrate that the proposed CC design has sensitivity comparable to PET. When the same number of events were considered, the computation time per iteration increased only by a factor of 2 when OE reconstruction with the resolution recovery correction was performed relative to the original OE algorithm. We estimate that the addition of resolution recovery to the OSEM would increase reconstruction times by 2-3 orders of magnitude per iteration. The results of our tests demonstrate the improvement of image resolution provided by the OE reconstructions

Resolution recovery for Compton camera using origin ensemble algorithm

Energy Technology Data Exchange (ETDEWEB)

Andreyev, A. [Philips Healthcare, Highland Heights, Ohio 44143 (United States); Celler, A. [Medical Imaging Research Group, University of British Columbia and Vancouver Coastal Health Research Institute, Vancouver, BC V5Z 1M9 (Canada); Ozsahin, I.; Sitek, A., E-mail: sarkadiu@gmail.com [Gordon Center for Medical Imaging, Massachusetts General Hospital, Boston, Massachusetts 02114 and Department of Radiology, Harvard Medical School, Boston, Massachusetts 02115 (United States)

2016-08-15

Purpose: Compton cameras (CCs) use electronic collimation to reconstruct the images of activity distribution. Although this approach can greatly improve imaging efficiency, due to complex geometry of the CC principle, image reconstruction with the standard iterative algorithms, such as ordered subset expectation maximization (OSEM), can be very time-consuming, even more so if resolution recovery (RR) is implemented. We have previously shown that the origin ensemble (OE) algorithm can be used for the reconstruction of the CC data. Here we propose a method of extending our OE algorithm to include RR. Methods: To validate the proposed algorithm we used Monte Carlo simulations of a CC composed of multiple layers of pixelated CZT detectors and designed for imaging small animals. A series of CC acquisitions of small hot spheres and the Derenzo phantom placed in air were simulated. Images obtained from (a) the exact data, (b) blurred data but reconstructed without resolution recovery, and (c) blurred and reconstructed with resolution recovery were compared. Furthermore, the reconstructed contrast-to-background ratios were investigated using the phantom with nine spheres placed in a hot background. Results: Our simulations demonstrate that the proposed method allows for the recovery of the resolution loss that is due to imperfect accuracy of event detection. Additionally, tests of camera sensitivity corresponding to different detector configurations demonstrate that the proposed CC design has sensitivity comparable to PET. When the same number of events were considered, the computation time per iteration increased only by a factor of 2 when OE reconstruction with the resolution recovery correction was performed relative to the original OE algorithm. We estimate that the addition of resolution recovery to the OSEM would increase reconstruction times by 2–3 orders of magnitude per iteration. Conclusions: The results of our tests demonstrate the improvement of image

Resolution recovery for Compton camera using origin ensemble algorithm

International Nuclear Information System (INIS)

Andreyev, A.; Celler, A.; Ozsahin, I.; Sitek, A.

2016-01-01

Purpose: Compton cameras (CCs) use electronic collimation to reconstruct the images of activity distribution. Although this approach can greatly improve imaging efficiency, due to complex geometry of the CC principle, image reconstruction with the standard iterative algorithms, such as ordered subset expectation maximization (OSEM), can be very time-consuming, even more so if resolution recovery (RR) is implemented. We have previously shown that the origin ensemble (OE) algorithm can be used for the reconstruction of the CC data. Here we propose a method of extending our OE algorithm to include RR. Methods: To validate the proposed algorithm we used Monte Carlo simulations of a CC composed of multiple layers of pixelated CZT detectors and designed for imaging small animals. A series of CC acquisitions of small hot spheres and the Derenzo phantom placed in air were simulated. Images obtained from (a) the exact data, (b) blurred data but reconstructed without resolution recovery, and (c) blurred and reconstructed with resolution recovery were compared. Furthermore, the reconstructed contrast-to-background ratios were investigated using the phantom with nine spheres placed in a hot background. Results: Our simulations demonstrate that the proposed method allows for the recovery of the resolution loss that is due to imperfect accuracy of event detection. Additionally, tests of camera sensitivity corresponding to different detector configurations demonstrate that the proposed CC design has sensitivity comparable to PET. When the same number of events were considered, the computation time per iteration increased only by a factor of 2 when OE reconstruction with the resolution recovery correction was performed relative to the original OE algorithm. We estimate that the addition of resolution recovery to the OSEM would increase reconstruction times by 2–3 orders of magnitude per iteration. Conclusions: The results of our tests demonstrate the improvement of image

Model predictive control of a waste heat recovery system for automotive diesel engines

NARCIS (Netherlands)

Feru, E.; Willems, F.P.T.; de Jager, A.G.; Steinbuch, M.

2014-01-01

In this paper, a switching Model Predictive Control strategy is designed for an automotive Waste Heat Recovery system with two parallel evaporators. The objective is to maximize Waste Heat Recovery system output power, while satisfying safe operation under highly dynamic disturbances from the

Inherently safe in situ uranium recovery

International Nuclear Information System (INIS)

Krumhansl, James Lee; Beauheim, Richard Louis; Brady, Patrick Vane; Arnold, Bill Walter; Kanney, Joseph F.; McKenna, Sean Andrew

2009-01-01

Expansion of uranium mining in the United States is a concern to some environmental groups and sovereign Native American Nations. An approach which may alleviate some problems is to develop inherently safe in situ uranium recovery ('ISR') technologies. Current ISR technology relies on chemical extraction of trace levels of uranium from aquifers that, once mined, can still contain dissolved uranium and other trace metals that are a health concern. Existing ISR operations are few in number; however, high uranium prices are driving the industry to consider expanding operations nation-wide. Environmental concerns and enforcement of the new 30 ppb uranium drinking water standard may make opening new mining operations more difficult and costly. Here we propose a technological fix: the development of inherently safe in situ recovery (ISISR) methods. The four central features of an ISISR approach are: (1) New 'green' leachants that break down predictably in the subsurface, leaving uranium, and associated trace metals, in an immobile form; (2) Post-leachant uranium/metals-immobilizing washes that provide a backup decontamination process; (3) An optimized well-field design that increases uranium recovery efficiency and minimizes excursions of contaminated water; and (4) A combined hydrologic/geochemical protocol for designing low-cost post-extraction long-term monitoring. ISISR would bring larger amounts of uranium to the surface, leave fewer toxic metals in the aquifer, and cost less to monitor safely - thus providing a 'win-win-win' solution to all stakeholders.

Assessing the recovery of coastal wetlands from oil spills

International Nuclear Information System (INIS)

Mendelssohn, I.A.; Hester, M.W.; Hill, J.M.

1993-01-01

The impact of oil spills on coastal environments and the ability of these systems to exhibit long-term recovery has received increased attention in recent years. Although oil spills can have significant short-term impacts on coastal marshes, the long-term effects and eventual recovery are not well documented. Estuarine marshes have sometimes been reported to exhibit slow recovery after oil spills, whereas in other instances they appear to have great resiliency, with complete recovery after one or two years. To document and understand this phenomenon better, we have investigated the long-term recovery of a south Louisiana estuarine marsh exposed to an accidental spill of crude oil. Although a pipeline rupture releasing Louisiana crude oil caused the near complete mortality of a brackish marsh dominated by Spartina patens and S. alterniflora, this marsh completely recovered four years after the spill with no differences in plant species cover between oiled and reference marshes. Remotely sensed imagery of the study site confirmed the relatively rapid recovery demonstrated by the ground truth data. Louisiana's coastal marshes are naturally experiencing rapid rates of deterioration. Land loss rates, determined from aerial imagery, at the spill site and adjacent reference areas before and after the spill demonstrated that the long-term loss rates were not affected by the spill event

Measuring disaster recovery: bouncing back or reaching the counterfactual state?

Science.gov (United States)

Cheng, Shaoming; Ganapati, Emel; Ganapati, Sukumar

2015-07-01

How should one measure the recovery of a locale from a disaster? The measurement is crucial from a public policy and administration standpoint to determine which places should receive disaster assistance, and it affects the performance evaluation of disaster recovery programmes. This paper compares two approaches to measuring recovery: (i) bouncing back to pre-disaster conditions; and (ii) attaining the counterfactual state. The former centres on returning to normalcy following disaster-induced losses, whereas the latter focuses on attaining the state, using quasi-experimental design, which would have existed if the disaster had not occurred. Both are employed here to assess two housing recovery indicators (total new units and their valuations) in Hurricane Katrina-affected counties (rural and urban). The examination reveals significantly different outcomes for the two approaches: counties have not returned to their pre-disaster housing conditions, but they do exhibit counterfactual recovery. Moreover, rural counties may not be as vulnerable as assumed in the disaster recovery literature. © 2015 The Author(s). Disasters © Overseas Development Institute, 2015.

Recovery from prolonged deep rocuronium-induced neuromuscular blockade: A randomized comparison of sugammadex reversal with spontaneous recovery.

Science.gov (United States)

Rahe-Meyer, N; Berger, C; Wittmann, M; Solomon, C; Abels, E A M; Rietbergen, H; Reuter, D A

2015-07-01

Deep neuromuscular blockade (NMB) may not always be maintained to the end of surgery and the depth of block may be allowed to gradually diminish over time, particularly if reversal of NMB is not routinely performed. The current study aimed to assess recovery from deep rocuronium-induced NMB with sugammadex compared with placebo, provide data regarding the extent of residual blockade after deep rocuronium-induced NMB (placebo group), and to determine whether complete and reliable recovery could be provided by sugammadex (sugammadex group). This was a randomized, placebo-controlled, safety-assessor-blinded study in adult patients of American Society of Anesthesiologists Class I to III. Patients with clinically relevant kidney or liver insufficiency were excluded. Anesthesia was administered as routinely practiced at each study site. Rocuronium 0.6 mg/kg was administered for intubation, with maintenance doses of 0.1-0.2 mg/kg as needed. After the last rocuronium dose, at deep NMB (target depth 1-2 post-tetanic counts), patients received a single dose of sugammadex 4.0 mg/kg or placebo as randomized. The primary endpoint was time from sugammadex or placebo administration to recovery of the train-of-four (TOF) ratio to 0.9. Safety was assessed through monitoring of adverse events, vital signs and physical examination. Patients were also assessed for evidence of residual or recurrence of NMB. With this design, the study will provide data regarding the extent of residual blockade under these conditions (placebo group), and determine whether complete and reliable recovery could be provided by sugammadex (sugammadex group). Recovery to a TOF ratio of ≥ 0.9 with sugammadex was significantly faster (~ 40 times) than spontaneous recovery: geometric mean (95 % confidence interval) times were 2.2 (1.9-2.5) and 89.8 (80.1-100.7) min, respectively (p sugammadex, with median time to recovery > 1.5 h in the placebo group and one patient taking 4.8 h to achieve a

Advanced Energy and Water Recovery Technology from Low Grade Waste Heat

Energy Technology Data Exchange (ETDEWEB)

Dexin Wang

2011-12-19

performance was also done, which shows this heat transfer enhancement approach works well in a wide parameters range for typical flue gas conditions. Better understanding of condensing heat transfer mechanism for porous membrane heat transfer surfaces, shows higher condensation and heat transfer rates than non-permeable tubes, due to existence of the porous membrane walls. Laboratory testing has documented increased TMC performance with increased exhaust gas moisture content levels, which has exponentially increased potential markets for the product. The TMC technology can uniquely enhance waste heat recovery in tandem with water vapor recovery for many other industrial processes such as drying, wet and dry scrubber exhaust gases, dewatering, and water chilling. A new metallic substrate membrane tube development and molded TMC part fabrication method, provides an economical way to expand this technology for scaled up applications with less than 3 year payback expectation. A detailed market study shows a broad application area for this advanced waste heat and water recovery technology. A commercialization partner has been lined up to expand this technology to this big market. This research work led to new findings on the TMC working mechanism to improve its performance, better scale up design approaches, and economical part fabrication methods. Field evaluation work needs to be done to verify the TMC real world performance, and get acceptance from the industry, and pave the way for our commercial partner to put it into a much larger waste heat and waste water recovery market. This project is addressing the priority areas specified for DOE Industrial Technologies Program's (ITP's): Energy Intensive Processes (EIP) Portfolio - Waste Heat Minimization and Recovery platform.

AECB Cost Recovery Fees Regulations, amendment

International Nuclear Information System (INIS)

1992-01-01

The amendments to the AECB Cost Recovery Fees Regulations have been made with a view to simplifying the registration procedure for obtaining such a certificate or approval under the above Transport Regulations. In effect there will no longer be a need for a separate fee system for registered users of certified package designs. (NEA)

Best practice in major elective rectal/pelvic surgery: enhanced recovery after surgery (ERAS)

OpenAIRE

Segelman, Josefin; Nygren, Jonas

2017-01-01

Within traditional clinical care, the postoperative recovery after pelvic/rectal surgery has been slow with high morbidity and long hospital stay. The enhanced recovery after surgery program is a multimodal approach to perioperative care designed to accelerate recovery and safely reduce hospital stay. This review will briefly summarize optimal perioperative care, before, during and after surgery in this group of patients and issues related to implementation and audit.

Plasma profile recovery by function parameterisation

International Nuclear Information System (INIS)

McCarthy, P.J.; Sexton, M.C.

1986-11-01

The use of Function Parameterisation for the recovery of plasma profiles as a function of flux surface area from spatial point data directly combined with external magnetic measurements is demonstrated in the case of ASDEX electron temperature and density profiles. The extrapolated temperature on the magnetic axis is shown to be more reliable than that obtained from a conventional fitting procedure. (orig.)

Motorcycle Area Design and Location: Impacts on the Recreational Experiences of Riders and Nonriders.

Science.gov (United States)

Bury, Richard L.; Fillmore, Edgar C.

This study analyzes some of the psychological and sociological effects of constructing motorcycle riding areas adjacent to fixed-site compgrounds. Findings include rider and camper profiles, self- and camper-perceptions of riders, and preferences and satisfactions of campers and riders concerning the proximity and design of riding areas.…

Comparison of methods for determining the hydrologic recovery time after forest disturbance

Science.gov (United States)

Oda, T.; Green, M.; Ohte, N.; Urakawa, R.; Endo, I.; Scanlon, T. M.; Sebestyen, S. D.; McGuire, K. J.; Katsuyama, M.; Fukuzawa, K.; Tague, C.; Hiraoka, M.; Fukushima, K.; Giambelluca, T. W.

2013-12-01

Changes in forest hydrology changes after forest disturbance vary among catchments. Although studies have summarized the initial runoff changes following forest disturbance, the estimates of long-term recovery time are less frequently reported. To understand the mechanisms of long-term recovery processes and to predict the long-term changes in streamflow after forest disturbance, it is important to compare recovery times after disturbance. However, there is no clear consensus regarding the best methodology for such research, especially for watershed studies that were not designed as paired watersheds. We compared methods of determining the hydrologic recovery time to determine if there is a common method for sites in any hydroclimatic setting. We defined the hydrologic recovery time to be the time of disturbance to the time when hydrological factors first recovered to pre-disturbance levels. We acquired data on long-term rainfall and runoff at 16 sites in northeastern USA and Japan that had at least 10 years (and up to 50 years) of post disturbance data. The types of disturbance include harvesting, diseases and insect damages. We compared multiple indices of hydrological response including annual runoff, annual runoff ratio (annual runoff/annual rainfall), annual loss (annual rainfall-annual runoff), fiftieth-percentile annual flow, and seasonal water balance. The results showed that comparing annual runoff to a reference site was most robust at constraining the recovery time, followed by using pre-disturbance data as reference data and calculating the differences in annual runoff from pre-disturbance levels. However, in case of small disturbance at sites without reference data or long-term pre-disturbance data, the inter-annual variation of rainfall makes the effect of disturbance unclear. We found that annual loss had smaller inter-annual variation, and defining recovery time with annual loss was best in terms of matching the results from paired watersheds. The

Critical factors for the recovery of marine mammals.

Science.gov (United States)

Lotze, Heike K; Flemming, Joanna Mills; Magera, Anna M

2017-12-01

{en} Over the past decades, much research has focused on understanding the critical factors for marine extinctions with the aim of preventing further species losses in the oceans. Although conservation and management strategies are enabling several species and populations to recover, others remain at low abundance levels or continue to decline. To understand these discrepancies, we used a published database on abundance trends of 137 populations of marine mammals worldwide and compiled data on 28 potentially critical factors for recovery. We then applied random forests and additive mixed models to determine which intrinsic and extrinsic factors are critical for the recovery of marine mammals. A mix of life-history characteristics, ecological traits, phylogenetic relatedness, population size, geographic range, human impacts, and management efforts explained why populations recovered or not. Consistently, species with lower age at maturity and intermediate habitat area were more likely to recover, which is consistent with life-history and ecological theory. Body size, trophic level, social interactions, dominant habitat, ocean basin, and habitat disturbance also explained some differences in recovery patterns. Overall, a variety of intrinsic and extrinsic factors were important for species' recovery, pointing to cumulative effects. Our results provide insight for improving conservation and management strategies to enhance recoveries in the future. © 2017 Society for Conservation Biology.

Recovery of energy in a gaseous diffusion plant

International Nuclear Information System (INIS)

Ergalant, Jacques; Guais, J.-C.; Perrault, Michel; Vignet, Paul

1975-01-01

Any energy recovery, even partial, goes in the direction of savings in energy and should be sought for. The Tricastin plant, now in the course of being built, will be able to deliver several hundreds of MW for the purpose of urban and agricultural heating. The new Coredif project will more completely integrate the valorization of calories in its definition (choice of temperatures, design of the heat exchangers, recovery cycles). In fact the recent evolution in energy costs renders the otpimization of a plant equipped with a heat recovery system (1 to 2% on the cost of the uranium produced) now economically worth-while. In the same way, the choice of the site of the future plant may be conditioned by the possible uses of calories in its vicinity [fr

Scarab/Saffron Development Project Case study: Material Selection Criteria for the Monoethylene Glycol Recovery Package

International Nuclear Information System (INIS)

Moussa, A.M.; Habib, S.; Shinaishin, A.

2004-01-01

MEG Recovery Unit for Scarab/Saffron development project is the first application in gas production. The Mono Ethylene Glycol Recovery Unit (MEG) recovers MEG from Water/MEG stream and removes salts and other contaminants. MEG Recovery Unit Equipment Design Criteria were designed for two parallel trains A and B, each train is capable to treat 500 bbl MEG, 1500 bbl water and 9 ton salt. The MEG unit is a combination of two unit operations; MEG Recovery unit is normally applicable in the oil and gas industries that is applying distillation technique, while the new technology is salt treatment and handling. The MEG Unit material selection is made to be suitable for the entire design life which is 25 years, the materials for MEG Recovery Unit have been selected among the available corrosion resistance alloys, where requested by the service and ambient conditions. Therefore all. the parts of the MEG unit that are in saline service are in either (2205 duplex, AISI 316L) and in Inconel alloy 625 related to operating temperature. This case study focused at Inconel alloy 625, which is selected for salt service and their operation problem occurred during the construction and operating conditions

Study on designing a complete pilot plant for processing sandstone ores in Palua-Parong area

International Nuclear Information System (INIS)

Le Quang Thai; Tran Van Son; Tran The Dinh; Trinh Nguyen Quynh; Vu Khac Tuan

2015-01-01

Design work is the first step of the construction and operation of pilot plant. Thus, the project Study on designing a complete pilot plant for processing sandstone ores in Palua - Parong area was conducted to design a pilot plant for testing entire technological process to obtain yellowcake. Based on a literature review of uranium ore processing technology in the world, information of ore and previous research results of uranium ore in PaLua - PaRong area at the Institute for Technology of Radioactive and Rare Elements, a suitable technological flowsheet for processing this ore has been selected. The size, location of the pilot plant and planed experiments has been selected during the implementation of this project, in which basic parameters, designed system of equipment, buildings, ect. were also calculated. (author)

Solvent Carryover Characterization and Recovery for a 10-inch Single Stage Centrifugal Contactor

International Nuclear Information System (INIS)

Lentsch, R.D.; Stephens, A.B.; Leung, D.T.; Baffling, K.E.; Harmon, H.D.; Suggs, P.C.

2006-01-01

A test program has been performed to characterize the organic solvent carryover and recovery from centrifugal contactors in the Caustic-side Solvent Extraction (CSSX) process. CSSX is the baseline design for removing cesium from salt solutions for Department of Energy (DOE) Savannah River Site's Salt Waste Processing Facility. CSSX uses a custom solvent to extract cesium from the salt solution in a series of single stage centrifugal contactors. Meeting the Waste Acceptance Criteria at the Defense Waste Processing Facility and Saltstone, as well as plant economics, dictate that solvent loss should be kept to a minimum. Solvent droplet size distribution in the aqueous outlet streams of the CSSX contactors is of particular importance to the design of solvent recovery equipment. Because insufficient solvent droplet size data existed to form a basis for the recovery system design, DOE funded the CSSX Solvent Carryover Characterization and Recovery Test (SCCRT). This paper presents the droplet size distribution of solvent and concentration in the contactor aqueous outlet streams as a function of rotor speed, bottom plate type, and flow rate. It also presents the performance data of a prototype coalescer. (authors)

Field Sampling Plan for Closure of the Central Facilities Area Sewage Treatment Plant Lagoon 3 and Land Application Area

International Nuclear Information System (INIS)

Lewis, Michael George

2016-01-01

This field sampling plan describes sampling of the soil/liner of Lagoon 3 at the Central Facilities Area Sewage Treatment Plant. The lagoon is to be closed, and samples obtained from the soil/liner will provide information to determine if Lagoon 3 and the land application area can be closed in a manner that renders it safe to human health and the environment. Samples collected under this field sampling plan will be compared to Idaho National Laboratory background soil concentrations. If the concentrations of constituents of concern exceed the background level, they will be compared to Comprehensive Environmental Response, Compensation, and Liability Act preliminary remediation goals and Resource Conservation and Recovery Act levels. If the concentrations of constituents of concern are lower than the background levels, Resource Conservation and Recovery Act levels, or the preliminary remediation goals, then Lagoon 3 and the land application area will be closed. If the Resource Conservation and Recovery Act levels and/or the Comprehensive Environmental Response, Compensation, and Liability Act preliminary remediation goals are exceeded, additional sampling and action may be required.

Field Sampling Plan for Closure of the Central Facilities Area Sewage Treatment Plant Lagoon 3 and Land Application Area

Energy Technology Data Exchange (ETDEWEB)

Lewis, Michael George [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-10-01

This field sampling plan describes sampling of the soil/liner of Lagoon 3 at the Central Facilities Area Sewage Treatment Plant. The lagoon is to be closed, and samples obtained from the soil/liner will provide information to determine if Lagoon 3 and the land application area can be closed in a manner that renders it safe to human health and the environment. Samples collected under this field sampling plan will be compared to Idaho National Laboratory background soil concentrations. If the concentrations of constituents of concern exceed the background level, they will be compared to Comprehensive Environmental Response, Compensation, and Liability Act preliminary remediation goals and Resource Conservation and Recovery Act levels. If the concentrations of constituents of concern are lower than the background levels, Resource Conservation and Recovery Act levels, or the preliminary remediation goals, then Lagoon 3 and the land application area will be closed. If the Resource Conservation and Recovery Act levels and/or the Comprehensive Environmental Response, Compensation, and Liability Act preliminary remediation goals are exceeded, additional sampling and action may be required.

300 Area Process Trenches Closure Plan

International Nuclear Information System (INIS)

Luke, S.N.

1994-01-01

Since 1987, Westinghouse Hanford Company has been a major contractor to the US Department of Energy, Richland Operations Office and has served as co-operator of the 300 Area Process Trenches, the waste management unit addressed in this closure plan. For the purposes of the Resource Conservation and Recovery Act, Westinghouse Hanford Company is identified as ''co-operator.'' The 300 Area Process Trenches Closure Plan (Revision 0) consists of a Resource Conservation and Recovery Act Part A Dangerous Waste Permit Application, Form 3 and a Resource Conservation and Recovery Act Closure Plan. An explanation of the Part A Permit Application, Form 3 submitted with this document is provided at the beginning of the Part A Section. The closure plan consists of nine chapters and six appendices. The 300 Area Process Trenches received dangerous waste discharges from research and development laboratories in the 300 Area and from fuels fabrication processes. This waste consisted of state-only toxic (WT02), corrosive (D002), chromium (D007), spent halogenated solvents (F001, F002, and F003), and spent nonhalogented solvent (F005). Accurate records are unavailable concerning the amount of dangerous waste discharged to the trenches. The estimated annual quantity of waste (item IV.B) reflects the total quantity of both regulated and nonregulated waste water that was discharged to the unit

Advanced heat pump for the recovery of volatile organic compounds

Energy Technology Data Exchange (ETDEWEB)

1992-03-01

Emissions of Volatile Organic Compounds (VOC) from stationary industrial and commercial sources represent a substantial portion of the total US VOC emissions. The Toxic-Release Inventory'' of The US Environmental Protection Agency estimates this to be at about 3 billion pounds per year (1987 estimates). The majority of these VOC emissions are from coating processes, cleaning processes, polymer production, fuel production and distribution, foam blowing,refrigerant production, and wood products production. The US Department of Energy's (DOE) interest in the recovery of VOC stems from the energy embodied in the recovered solvents and the energy required to dispose of them in an environmentally acceptable manner. This Phase I report documents 3M's work in close working relationship with its subcontractor Nuclear Consulting Services (Nucon) for the preliminary conceptual design of an advanced Brayton cycle heat pump for the recovery of VOC. Nucon designed Brayton cycle heat pump for the recovery of methyl ethyl ketone and toluene from coating operations at 3M Weatherford, OK, was used as a base line for the work under cooperative agreement between 3M and ODE. See appendix A and reference (4) by Kovach of Nucon. This cooperative agreement report evaluates and compares an advanced Brayton cycle heat pump for solvent recovery with other competing technologies for solvent recovery and reuse. This advanced Brayton cycle heat pump is simple (very few components), highly reliable (off the shelf components), energy efficient and economically priced.

Designer-Wet Micromodels for Studying Potential Changes in Wettability during Microbial Enhanced Oil Recovery

Science.gov (United States)

Armstrong, R. T.; Wildenschild, D.

2010-12-01

Microbial Enhanced Oil Recovery (MEOR) is a process where microorganisms are used for tertiary recovery of oil. Some bacteria can facilitate the mobilization of oil through the production of amphiphilic compounds called biosurfactants that reduce the interfacial tension (IFT) between immiscible phases. Additionally, most bacteria have an inclination to colonize surfaces and form biofilm, which can change a reservoir's wetting properties or clog preferential flow paths. Herein, we aim to understand changes in wettability during MEOR under mixed wettability conditions within silicon etched micromodels and to identify the type of oil field (i.e. based on wettability) in which MEOR is likely to be most profitable. To quantify porous media wettability, macro-scale indexes (obtained with techniques such as the Carter or Amott methods) are used regularly. However, these measurements lack the capability for characterization of changes in wettability during MEOR treatment, and only provide macro-scale information. In an effort to understand micro-scale temporal and spatial changes in wettability we measure interfacial curvature from stereo microscope images using level set methods. Curvature, from the perspective of the oil phase, is positive for a concave interface (i.e. water-wet surface) and negative for a convex interface (i.e. oil-wet surface). Thus, shifts in the radius of curvature distribution (i.e. from positive to negative or conversely) are indicative of wettability changes. Both curvature distributions using level-set methods and the Carter method are used to characterize wettability before and after microbial treatment. In preliminary studies aimed at understanding wettability changes due to microbial surface interactions by Bacillus mojavensis JF-2, oil droplets were placed on glass slides suspended in growth media and the resulting contact angle was measured over time. Results showed that a water-wet surface will become more water wet as JF-2 accumulated in

Exposure to nature versus relaxation during lunch breaks and recovery from work: development and design of an intervention study to improve workers’ health, well-being, work performance and creativity

Science.gov (United States)

2014-01-01

Background The objective of this research project is to understand and to improve workers’ recovery from work stress. Although recovery during lunch breaks is the most common within-workday break, it has received only minor research attention. Therefore, we will study whether lunch breaks including a relaxation session or exposure to nature have more favorable outcomes than usually spent lunch breaks concerning: a) recovery processes, b) health, c) well-being, d) job performance and e) creativity. We approach recovery by combining the theoretical frameworks of work and environmental psychology. Methods/Design We conduct an intervention study in a sample of 268 knowledge-workers who engage in different lunch break activities for 15-minutes per day, two weeks in a row. We randomly assign participants to three experimental conditions: 1) exposure to nature, 2) relaxation and 3) control group (lunch break spent as usual). Online questionnaires before and after the intervention assess long term changes regarding recovery processes and the major outcome variables. Before, during and after the intervention, SMS and paper-pencil questionnaires measure the same constructs four times a day with fewer items. We also measure blood pressure and collect saliva samples to map cortisol excretion across the intervention period. A timed experimental task (i.e., the Alternative Uses Task) is used to examine differences in creativity between the three groups after the intervention period. Discussion By combining the knowledge of work and environmental psychology about recovery and restorative experiences, by merging three recovery perspectives (settings, processes, and outcomes) and by using data triangulation, we produce valid results that broaden our view on mechanisms underlying recovery and enhance our understanding about their links to psychological, behavioural and physiological outcomes, resulting in a more comprehensive picture of work stress recovery in general. Trial

People, Aid and institutions in socio-economic recovery

NARCIS (Netherlands)

Hilhorst, Thea; Weijs, Bart; Haar, van der Gemma

2017-01-01

An estimated 2 billion people live in countries affected by fragility, conflict and violence. Extreme poverty is increasingly concentrated in these areas, and governments and international agencies seek avenues to enable socio-economic recovery and to support people as they try to rebuild their

Increasing CO2 storage in oil recovery

International Nuclear Information System (INIS)

Jessen, K.; Kovscek, A.R.; Orr, F.M. Jr.

2005-01-01

Oil fields offer a significant potential for storing CO 2 and will most likely be the first large scale geological targets for sequestration as the infrastructure, experience and permitting procedures already exist. The problem of co-optimizing oil production and CO 2 storage differs significantly from current gas injection practice due to the cost-benefit imbalance resulting from buying CO 2 for enhanced oil recovery projects. Consequently, operators aim to minimize the amount of CO 2 required to sweep an oil reservoir. For sequestration purposes, where high availability of low cost CO 2 is assumed, the design parameters of enhanced oil recovery processes must be re-defined to optimize the amount of CO 2 left in the reservoir at the time of abandonment. To redefine properly the design parameters, thorough insight into the mechanisms controlling the pore scale displacement efficiency and the overall sweep efficiency is essential. We demonstrate by calculation examples the different mechanisms controlling the displacement behavior of CO 2 sequestration schemes, the interaction between flow and phase equilibrium and how proper design of the injection gas composition and well completion are required to co-optimize oil production and CO 2 storage. [Author

Increasing CO2 storage in oil recovery

International Nuclear Information System (INIS)

Jessen, Kristian; Kovscek, Anthony R.; Orr, Franklin M.

2005-01-01

Oil fields offer a significant potential for storing CO 2 and will most likely be the first large scale geological targets for sequestration as the infrastructure, experience and permitting procedures already exist. The problem of co-optimizing oil production and CO 2 storage differs significantly from current gas injection practice due to the cost-benefit imbalance resulting from buying CO 2 for enhanced oil recovery projects. Consequently, operators aim to minimize the amount of CO 2 required to sweep an oil reservoir. For sequestration purposes, where high availability of low cost CO 2 is assumed, the design parameters of enhanced oil recovery processes must be re-defined to optimize the amount of CO 2 left in the reservoir at the time of abandonment. To redefine properly the design parameters, thorough insight into the mechanisms controlling the pore scale displacement efficiency and the overall sweep efficiency is essential. We demonstrate by calculation examples the different mechanisms controlling the displacement behavior of CO 2 sequestration schemes, the interaction between flow and phase equilibrium and how proper design of the injection gas composition and well completion are required to co-optimize oil production and CO 2 storage

Industrial Waste Heat Recovery - Potential Applications, Available Technologies and Crosscutting R&D Opportunities

Energy Technology Data Exchange (ETDEWEB)

Thekdi, Arvind [E3M Inc, North Potomac, MD (United States); Nimbalkar, Sachin U. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-01-01

The purpose of this report was to explore key areas and characteristics of industrial waste heat and its generation, barriers to waste heat recovery and use, and potential research and development (R&D) opportunities. The report also provides an overview of technologies and systems currently available for waste heat recovery and discusses the issues or barriers for each. Also included is information on emerging technologies under development or at various stages of demonstrations, and R&D opportunities cross-walked by various temperature ranges, technology areas, and energy-intensive process industries.

The D0 online monitoring and automatic DAQ recovery

International Nuclear Information System (INIS)

Haas, A.

2004-01-01

The DZERO experiment, located at the Fermi National Accelerator Laboratory, has recently started the Run 2 physics program. The detector upgrade included a new Data Acquisition/Level 3 Trigger system. Part of the design for the DAQ/Trigger system was a new monitoring infrastructure. The monitoring was designed to satisfy real-time requirements with 1-second resolution as well as nonreal-time data. It was also designed to handle a large number of displays without putting undue load on the sources of monitoring information. The resulting protocol is based on XML, is easily extensible, and has spawned a large number of displays, clients, and other applications. It is also one of the few sources of detector performance available outside the Online System's security wall. A tool, based on this system, which provides for auto-recovery of DAQ errors, has been designed. This talk will include a description of the DZERO DAQ/Online monitor server, based on the ACE framework, the protocol, the auto-recovery tool, and several of the unique displays which include an ORACLE-based archiver and numerous GUIs

Lessons Learned from the Node 1 Atmosphere Control and Storage and Water Recovery and Management Subsystem Design

Science.gov (United States)

Williams, David E.

2011-01-01

Node 1 flew to the International Space Station (ISS) on Flight 2A during December 1998. To date the National Aeronautics and Space Administration (NASA) has learned a lot of lessons from this module based on its history of approximately two years of acceptance testing on the ground and currently its twelve years on-orbit. This paper will provide an overview of the ISS Environmental Control and Life Support (ECLS) design of the Node 1 Atmosphere Control and Storage (ACS) and Water Recovery and Management (WRM) subsystems and it will document some of the lessons that have been learned to date for these subsystems based on problems prelaunch, problems encountered on-orbit, and operational problems/concerns. It is hoped that documenting these lessons learned from ISS will help in preventing them in future Programs.

Visualization of the functional recovery process of brain and spinal cord after injury

International Nuclear Information System (INIS)

Isa, Tadashi

2009-01-01

Elucidation of the process of spontaneous functional recovery of central nervous system (CNS) after injury like trauma and stroke is important to develop and conduct the better rehabilitation training to promote the recuperation. Authors have developed a macaque monkey model with an artificial injury of cervical corticospinal tract (CST), where its elaborative motor activity of fingers spontaneously recovers. This paper describes the selective CST injury procedure, its recovery process in finger movement and in CNS images by positron emission tomography (PET), and validation of the obtained images by nerve block. For the injury, CST is cut selectively at monkey's C4/C5 boundary to block the hand motion nerve and to preserve the 2-synapse pathway through the propriospinal neuron, which results in acute loss of grasping a piece of potato food. At 1-3 months after the treatment, the elaborative motor activity of fingers completely recovers. During this recovery period, PET is conducted to trace the brain blood flow change at the upper center of the motion in realizing/grasping food, where the dorsal pathway and cerebellar nuclei are activated at the motion in the untreated animal. At 1-2 months after operation, the blood flow is found increased in the two areas above and the increased area, widened relative to those before operation. At 3 months (at complete functional recovery), the activity in the ipsilateral primary motor area returns to normal level and in the contralateral area, is spread accompanying the increase in the bilateral dorsal premotor and secondary somatosensory areas. Imaging results are validated by nerve block with micro-injection of muscimol into the activated areas during the task motor. Findings are helpful for developing a method to promote the compensation of nervous function after injury. (K.T.)

Ongoing Recovery Basic Information Tool (ORBIT)

Science.gov (United States)

Oberg, Donald

1993-01-01

The Federal Drug Free Work Place Program (DFWP) has now matured to the point of being able to return employees to sensitive testing designated positions (TDP) after completion of treatment of their addiction. The known tendency of addicted individuals to suffer multiple relapses prior to their final recovery has resulted in several positive urine tests (relapses) occurring among those Federal employees who have already completed treatment and who have been returned to TDP's. The very real potential for further relapses occurring after additional employees return to TDP's will be a critical factor in the ultimate success of the DFWP and in the public's impression of the program's effectiveness. In response to this concern, NASA has begun development of its Ongoing Recovery Basic Information Tool (ORBIT) instrument. The aim of the NASA ORBIT is to provide Employee Assistance Program (EAP) professionals with an advanced clinical tool which will be helpful in supporting recovery from substance abuse and which will allow more accurate determinations of when clients may be successfully returned to sensitive positions.

Design of a broadband ultra-large area acoustic cloak based on a fluid medium

Science.gov (United States)

Zhu, Jian; Chen, Tianning; Liang, Qingxuan; Wang, Xiaopeng; Jiang, Ping

2014-10-01

A broadband ultra-large area acoustic cloak based on fluid medium was designed and numerically implemented with homogeneous metamaterials according to the transformation acoustics. In the present work, fluid medium as the body of the inclusion could be tuned by changing the fluid to satisfy the variant acoustic parameters instead of redesign the whole cloak. The effective density and bulk modulus of the composite materials were designed to agree with the parameters calculated from the coordinate transformation methodology by using the effective medium theory. Numerical simulation results showed that the sound propagation and scattering signature could be controlled in the broadband ultra-large area acoustic invisibility cloak, and good cloaking performance has been achieved and physically realized with homogeneous materials. The broadband ultra-large area acoustic cloaking properties have demonstrated great potentials in the promotion of the practical applications of acoustic cloak.

Design and implementation of a web-based data grid management system for enterprise PACS backup and disaster recovery

Science.gov (United States)

Zhou, Zheng; Ma, Kevin; Talini, Elisa; Documet, Jorge; Lee, Jasper; Liu, Brent

2007-03-01

A cross-continental Data Grid infrastructure has been developed at the Image Processing and Informatics (IPI) research laboratory as a fault-tolerant image data backup and disaster recovery solution for Enterprise PACS. The Data Grid stores multiple copies of the imaging studies as well as the metadata, such as patient and study information, in geographically distributed computers and storage devices involving three different continents: America, Asia and Europe. This effectively prevents loss of image data and accelerates data recovery in the case of disaster. However, the lack of centralized management system makes the administration of the current Data Grid difficult. Three major challenges exist in current Data Grid management: 1. No single user interface to access and administrate each geographically separate component; 2. No graphical user interface available, resulting in command-line-based administration; 3. No single sign-on access to the Data Grid; administrators have to log into every Grid component with different corresponding user names/passwords. In this paper we are presenting a prototype of a unique web-based access interface for both Data Grid administrators and users. The interface has been designed to be user-friendly; it provides necessary instruments to constantly monitor the current status of the Data Grid components and their contents from any locations, contributing to longer system up-time.

Overcoming challenges to the recovery of declining amphibian populations in the United States

Science.gov (United States)

Walls, Susan; Ball, Lianne C.; Barichivich, William J.; Dodd, Kenneth; Enge, Kevin M; Gorman, Thomas A.; O'Donnell, Katherine; Palis, John G; Semlitsch, Raymond D.

2016-01-01

The US Endangered Species Act of 1973 (ESA) affords many potential benefits to species threatened with extinction. However, most at-risk amphibians—one of the most imperiled vertebrate groups—remain unlisted under the provisions of the ESA, and many impediments to recovery exist for those species that have been listed. Of the 35 US amphibian species and distinct population segments (“taxa”) listed under the ESA, 40% currently lack a final (completed) recovery plan, 28.6% lack designated critical habitat, and 8.6% lack both. For taxa that have recovery plans, the time between their listing and the development of those plans was from 2 to 29 years, and the time between their listing and the designation of critical habitat ranged from 0 to 14 years. The underlying causes of such delays in protection are complex and constitute obstacles to recovery of imperiled species. We outline a series of strategic actions by which these challenges may be overcome.

HEAVY AND THERMAL OIL RECOVERY PRODUCTION MECHANISMS

Energy Technology Data Exchange (ETDEWEB)

Anthony R. Kovscek; Louis M. Castanier

2002-09-30

The Stanford University Petroleum Research Institute (SUPRI-A) conducts a broad spectrum of research intended to help improve the recovery efficiency from difficult to produce reservoirs including heavy oil and fractured low permeability systems. Our scope of work is relevant across near-, mid-, and long-term time frames. The primary functions of the group are to conduct direction-setting research, transfer research results to industry, and educate and train students for careers in industry. Presently, research in SUPRI-A is divided into 5 main project areas. These projects and their goals include: (1) Multiphase flow and rock properties--to develop better understanding of the physics of displacement in porous media through experiment and theory. This category includes work on imbibition, flow in fractured media, and the effect of temperature on relative permeability and capillary pressure. (2) Hot fluid injection--to improve the application of nonconventional wells for enhanced oil recovery and elucidate the mechanisms of steamdrive in low permeability, fractured porous media. (3) Mechanisms of primary heavy oil recovery--to develop a mechanistic understanding of so-called ''foamy oil'' and its associated physical chemistry. (4) In-situ combustion--to evaluate the effect of different reservoir parameters on the insitu combustion process. (5) Reservoir definition--to develop and improve techniques for evaluating formation properties from production information. What follows is a report on activities for the past year. Significant progress was made in all areas.

Design of a predictive control strategy for an automotive electrically-assisted waste heat recovery system with preview

NARCIS (Netherlands)

Seretis, M.

2017-01-01

This report regards the development of a predictive control strategy for an automotive electrically-assisted Waste Heat Recovery System (eWHR) with preview information. In this system, the energy recovery is decoupled from the energy supply to the engine. For such dynamical systems with energy

Ethnicity and cultural models of recovery from breast cancer.

Science.gov (United States)

Coreil, Jeannine; Corvin, Jaime A; Nupp, Rebecca; Dyer, Karen; Noble, Charlotte

2012-01-01

Recovery narratives describe the culturally shared understandings about the ideal or desirable way to recover from an illness experience. This paper examines ethnic differences in recovery narratives among women participating in breast cancer support groups in Central Florida, USA. It compares groups serving African-American, Latina, and European American women, with the objective of better understanding the appeal of ethnic-specific illness support groups for culturally diverse populations. A mixed-method study design combined qualitative and quantitative measures, including in-depth interviews, participant observation at support group meetings, collection of printed documents, and a structured survey. Core elements of the recovery narrative drew from the dominant societal cancer discourse of optimism and personal transformation through adversity; however, important ethnic differences were evident in the meaning assigned to these themes. Groups gave distinctive salience to themes of faith and spirituality, empowerment through the migration experience, and becoming a better person through the journey of recovery. The findings suggest that ethnic cancer support groups draw upon dominant societal discourses about cancer, but they espouse distinctive recovery narratives that are consonant with the groups' cultural models of illness. Similarity between ethnic members' individual recovery narratives and that of the group may contribute to the appeal of ethnic illness support groups for culturally diverse populations.