WorldWideScience

Sample records for reclaimed limestone residual

  1. Residual CO2 trapping in Indiana limestone.

    Science.gov (United States)

    El-Maghraby, Rehab M; Blunt, Martin J

    2013-01-02

    We performed core flooding experiments on Indiana limestone using the porous plate method to measure the amount of trapped CO(2) at a temperature of 50 °C and two pressures: 4.2 and 9 MPa. Brine was mixed with CO(2) for equilibration, then the mixture was circulated through a sacrificial core. Porosity and permeability tests conducted before and after 884 h of continuous core flooding confirmed negligible dissolution. A trapping curve for supercritical (sc)CO(2) in Indiana showing the relationship between the initial and residual CO(2) saturations was measured and compared with that of gaseous CO(2). The results were also compared with scCO(2) trapping in Berea sandstone at the same conditions. A scCO(2) residual trapping end point of 23.7% was observed, indicating slightly less trapping of scCO(2) in Indiana carbonates than in Berea sandstone. There is less trapping for gaseous CO(2) (end point of 18.8%). The system appears to be more water-wet under scCO(2) conditions, which is different from the trend observed in Berea; we hypothesize that this is due to the greater concentration of Ca(2+) in brine at higher pressure. Our work indicates that capillary trapping could contribute to the immobilization of CO(2) in carbonate aquifers.

  2. Formulation and characterization of structural lightweight concrete containing residues of porcelain tile polishing, tire rubber and limestone

    Directory of Open Access Journals (Sweden)

    Z. L. M. Sampaio

    Full Text Available Abstract The recent increase in the construction industry has transformed concrete into an ideal choice to recycle a number of residues formerly discarded into the environment. Among various products, porcelain tile polishing, limestone and tire rubber residues are potential candidates to replace the fine aggregate of conventional mixtures. The aim of this study was to investigate the effect of the addition of varying contents of these residues in lightweight concrete where expanded clay replaced gravel. To that end, slump, compressive strength, density, void ratio, porosity and absorption tests were carried out. The densities of all concrete formulations studied were 10% lower to that of lightweight concrete (<1.850 kg/m³. Nevertheless, mixes containing 10 to 15% of combined residues reduced absorption, void ratio and porosity, at least 17% lower compared to conventional concrete. The strength of such formulations reached 27 MPa at 28 days with consistency of 9 to 12 cm, indicating adequate consistency and increased strength. In addition, the combination of low porosity, absorption and voids suggested improved durability.

  3. Influence of biochar and plant growth on organic matter dynamics in a reclaimed mine residue

    Science.gov (United States)

    Moreno-Barriga, Fabián; Díaz, Vicente; Alberto, Jose; Faz, Ángel; Zornoza, Raúl

    2016-04-01

    This study aims at assessing the impact of biochar and marble waste amendment and the development of vegetation in acidic mine wastes on organic matter dynamics. For this purpose, a mine residue was collected in a tailing pond from the Sierra Minera of Cartagena-La Unión (SE Spain), and a greenhouse experiment was established for 120 days. Marble waste (MW) was added in a rate of 200 g kg-1 as a source of calcium carbonate to increase the pH from 3 to 7.5-8 (average pH in the native soils of the area). We added biochar as a source of organic carbon and nutrients, in two different rates, 50 g kg-1 (BC1) and 100 g kg-1 (BC2). To assess the influence of vegetation growth on the creation of a technosoil from mine residues and its impact on organic matter dynamics, the plant species Piptatherum miliaceum (PM) was planted in half the pots with the different amendments. Thus, five treatments were established: unamended and unplanted control (CT), BC1, BC2, BC1+PM and BC2+PM. Results showed that the different treatments had no significant effect on aggregates stability, microbial biomass carbon and the emission of N2O and CH4. So, it seems that longer periods are needed to increase the stability of aggregates and microbial populations, since even the combined use of biochar, marble waste and vegetation was not enough to increase these properties in 120 days. Nonetheless, it was positive that the addition of biochar and the release of root exudates did not trigger the emission of greenhouse gases. Organic carbon significantly increased with the addition of biochar, with values similar to the dose applied, indicating high stability and low mineralization of the amendment. The addition of amendments significantly increased arylesterase activity, while the growth of the plant was needed to significantly increase β-glucosidase activity. The soluble carbon significantly decreased in BC1 and BC2 with regards to CT, while no significant differences were observed among CT and

  4. Use of filler limestone and construction and demolition residues for remediating soils contaminated with heavy metals: an assessment by means of plant uptake.

    Science.gov (United States)

    Banegas, Ascension; Martinez-Sanchez, Maria Jose; Agudo, Ines; Perez-Sirvent, Carmen

    2010-05-01

    A greenhouse trial was carried out to evaluate the assimilation of heavy metals by three types of horticultural plants (lettuce, broccoli and alfalfa), different parts of which are destined for human and animal consumption (leaves, roots, fruits). The plants were cultivated in four types of soil, one uncontaminated (T1), one soil collected in the surrounding area of Sierra Minera (T2), the third being remediated with residues coming from demolition and construction activities (T3) and the four remediated with filler limestone (T4). To determine the metal content, soil samples were first ground to a fine powder using an agate ball mill. Fresh vegetable samples were separated into root and aboveground biomass and then lyophilized. The DTPA-extractable content was also determined to calculate the bioavailable amount of metal. Finally, the translocation factor (TF) and bioconcentration factor (BCF) were calculated. Arsenic levels were obtained by using atomic fluorescence spectrometry with an automated continuous flow hydride generation (HG-AFS) spectrometer and Cd, Pb and Zn was determined by electrothermal atomization atomic absorption spectrometry (ETAAS) or flame atomic absorption spectrometry (FAAS). Samples of the leached water were also obtained and analyzed. According to our results, the retention of the studied elements varies with the type of plant and is strongly decreased by the incorporation of filler limestone and/or construction and demolition residues to the soils. This practice represents a suitable way to reduce the risk posed to the biota by the presence of high levels of heavy metal in soil.

  5. Heavy metal water pollution associated with the use of sewage sludge compost and limestone outcrop residue for soil restoration: effect of saline irrigation.

    Science.gov (United States)

    Pérez-Gimeno, Ana; Navarro-Pedreño, Jose; Gómez, Ignacio; Belén Almedro-Candel, María; Jordán, Manuel M.; Bech, Jaume

    2015-04-01

    The use of composted sewage sludge and limestone outcrop residue in soil restoration and technosol making can influence the mobility of heavy metals into groundwater. The use of compost from organic residues is a common practice in soil and land rehabilitation, technosol making, and quarry restoration (Jordán et al. 2008). Compost amendments may improve the physical, chemical, and biological properties of soils (Jordão et al. 2006; Iovieno et al. 2009). However, the use of compost and biosolids may have some negative effects on the environment (Karaca 2004; Navarro-Pedreño et al. 2004). This experiment analyzed the water pollution under an experimental design based on the use of columns (0-30 cm) formed by both wastes. Two waters of different quality (saline and non-saline) were used for irrigation. The presence of heavy metals (Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn) in the leachates was checked under controlled conditions inside a greenhouse (mean values: 20°±5°C and around 60% relative humidity). Sixteen 30-cm tall columns made of PVC pipe with internal diameters of 10.5 cm were prepared. The columns were filled with one of these materials: either sewage sludge compost (SW) or limestone outcrop residue (LR), fraction (determine if the accumulation of heavy metals in waters may be determinant for future pollution. References: Iovieno P, Morra L, Leone A, Pagano L, Alfani A (2009) Effect of organic and mineral fertilizers on soil respiration and enzyme activities of two Mediterranean horticultural soils. Biol Fert Soils doi:10.1007/s00374-009-0365-z. Jordán MM, Pina S, García-Orenes F, Almendro-Candel MB, García-Sánchez E (2008) Environmental risk evaluation of the use of mine spoils and treated sewage sludge in the ecological restoration of limestone quarries. Environ Geol doi:10.1007/s00254-007-0991-4. Jordão CP, Nascentes CC, Cecon PR, Fontes RLF, Pereira JL (2006) Heavy metal availability in soil amended with composted urban solid wastes. Environ Monit

  6. Vertical distribution, composition profiles, sources and toxicity assessment of PAH residues in the reclaimed mudflat sediments from the adjacent Thane Creek of Mumbai.

    Science.gov (United States)

    Basavaiah, N; Mohite, R D; Singare, P U; Reddy, A V R; Singhal, R K; Blaha, U

    2017-05-15

    A study on vertical distribution of magnetic susceptibility, carcinogenic and endocrine disrupting PAHs was performed in the reclaimed mudflat sediments adjacent to the Thane Creek of Mumbai. The 5-rings PAHs and ΣC-PAHs were more dominant at 120cm depth contributing 52.23% and 60.19% respectively to ∑PAHs. The average ratio values of LMW/HMW PAHs (0.58); Fla/(Fla+Pyr) (0.50); Ant/(Ant+Phe) (0.50); BaA/(Chry+BaA) (0.48); BaP/BghiP (2.06), Phe/Ant (1.03) and BaA/Chr (0.93) indicate that the PAH contamination might have raised due to inefficient combustion and pyrogenic emissions during the open burning of solid waste in the vicinity. This was further supported by the anthropogenic ferri(o)magnetic loading over the last 100years influencing the Creek sediments. The PAHs toxicity estimation was performed by calculating the toxic equivalent quantity (TEQ) value of 8.62ng TEQ/g which was below the safe level (600ng TEQ/g) suggested by the Canadian risk-based soil criterion for protection of human health. Copyright © 2017 Elsevier Ltd. All rights reserved.

  7. Aplicação superficial de calcário e diferentes resíduos em soja cultivada no sistema plantio direto Surface application of limestone and different residues on soybean grown in no-till system

    Directory of Open Access Journals (Sweden)

    Juliano Corulli Corrêa

    2009-01-01

    Full Text Available A prática da correção da acidez do solo pela aplicação superficial de corretivos sobre a palha no sistema plantio direto se restringe ao calcário, não havendo maiores estudos em relação à escória de aciaria, lama cal e lodo de esgoto centrifugado. O objetivo do trabalho foi avaliar os índices de acidez do solo e a produtividade da soja em função da aplicação superficial de lodo de esgoto centrifugado, lama cal, escória de aciaria e calcário dolomítico. O trabalho foi desenvolvido em Latossolo Vermelho distrófico, durante os anos agrícolas de 2002 a 2005, sob sistema plantio direto. Os tratamentos constituíram da aplicação superficial de escória de aciaria (E, lama cal (Lcal, lodo de esgoto centrifugado (LC, calcário dolomítico e sem aplicação de corretivo, em delineamento em blocos ao acaso, com quatro repetições. A aplicação superficial de escória de aciaria, lama cal e lodo de esgoto centrifugado permite a correção da acidez do solo, o deslocamento do Ca2+, o aumento da saturação por bases e redução do Al3+ até 40 cm, e para o calcário, até 20 cm, fatores que condicionaram o aumento da produtividade da soja para os tratamentos LC, E e Lcal em 2003/2004 e 2004/2005 e para LC e E em 2002/2003 no sistema plantio direto.The practice of correcting soil acidity by surface application of pH-correcting materials on crop residues in the no-till system is restricted to limestone. No further studies are available on the use of steel slag, lime mud, and centrifuged sewage sludge. The objective of this study was to evaluate soil acidity and yield of soybean as a function of surface application of centrifuged sewage sludge, lime mud, steel slag, and dolomitic limestone. The study was conducted on a dystrophic Clayey Rhodic Hapludox soil, during the 2002_2005 cropping seasons, under notill system. Treatments consisted on surface application of slag _ E, lime mud _ Lcal, centrifuged sewage sludge _ LC, dolomitic

  8. Incorporation of limestone residue from marble processing plant in the city of Cachoeiro do Itapemirim, Espirito Santo, Brazil, in the production of mortars

    International Nuclear Information System (INIS)

    Goncalves, G.P.; Alexandre, J.; Dias, D.P.; Dias Junior, N.S.; Anderson, R.B.

    2010-01-01

    Cachoeiro do Itapemirim city (ES), located 136 km from Vitoria, the state's capital, is the largest ornamental stones producer in Brazil, whose beneficiation produces a large amount of waste that, even today, is responsible for major damages done to the environment. This article aims the experimental study of hydrated lime use (product marketed to be used in mortar) by a residue from marble beneficiation from an industry located in that city. Two mixes were made with cement:sand:hydrated lime and cement:sand:residue. The mortars were evaluated by their properties comparisons in fresh and hardened states, namely: consistency index, mass density and incorporated air content, compressive strength, tensile and bending grip for traction. Chemical and mineralogical analysis by X-ray diffraction were also made. The obtained results met the requirements prescribed by ABNT NBR 13 281 (2005). (author)

  9. Direct Sulfation of Limestone

    DEFF Research Database (Denmark)

    Hu, Guilin; Dam-Johansen, Kim; Wedel, Stig

    2007-01-01

    The direct sulfation of limestone was studied in a laboratory fixed-bed reactor. It is found that the direct sulfation of limestone involves nucleation and crystal grain growth of the solid product (anhydrite). At 823 K and at low-conversions (less than about 0.5 %), the influences of SO2, O-2...... and CO2 on the direct sulfation of limestone corresponds to apparent reaction orders of about 0.2, 0.2 and -0.5, respectively. Water is observed to promote the sulfation reaction and increase the apparent reaction orders of SO2 and O-2. The influence of O-2 at high O-2 concentrations (> about 15...... %) becomes negligible. In the temperature interval from 723 K to 973 K, an apparent activation energy of about 104 kJ/mol is observed for the direct sulfation of limestone. At low temperatures and low conversions, the sulfation process is most likely under mixed control by chemical reaction and solid...

  10. Water Reuse: Using Reclaimed Water For Irrigation

    OpenAIRE

    Haering, Kathryn; Evanylo, Gregory K.; Benham, Brian Leslie, 1960-; Goatley, Michael

    2009-01-01

    Describes water reuse and reclaimed water, explains how reclaimed water is produced, options for water reuse, water reuse regulations, and agronomic concerns with water reuse, and provides several case studies of water reuse.

  11. Optimisation of a wet FGD pilot plant using fine limestone and organic acids

    DEFF Research Database (Denmark)

    Frandsen, Jan; Kiil, Søren; Johnsson, Jan Erik

    2001-01-01

    , but the residual limestone content in the gypsum increased to somewhere between 19 and 30 wt%, making this pH range unsuitable for use in a full-scale plant. The investigations have shown that both the addition of organic acids and the use of a limestone with a fine PSD can be used to optimise wet FGD plants. (C......The effects of adding an organic acid or using a limestone with a fine particle size distribution (PSD) have been examined in a wet flue gas desulphurisation (FGD) pilot plant. Optimisation of the plant with respect to the degree of desulphurisation and the residual limestone content of the gypsum...... has been the aim of the work. In contrast to earlier investigations with organic acids, all essential process parameters (i.e. gas phase concentration profiles of SO(2), slurry pH profiles. and residual limestone in the gypsum) were considered. Slurry concentrations of adipic acid in the range of 0...

  12. Reclaiming Accountability in Teacher Education

    Science.gov (United States)

    Cochran-Smith, Marilyn; Carney, Molly Cummings; Keefe, Elizabeth Stringer; Burton, Stephani; Chang, Wen-Chia; Fernández, M. Beatriz; Miller, Andrew F.; Sánchez, Juan Gabriel; Baker, Megina

    2018-01-01

    Teacher accountability has been a major strategy for "fixing" education for the last 2 decades. In this book, Cochran-Smith and her research team argue that it is time for teacher educators to reclaim accountability by adopting a new approach that features intelligent professional responsibility, challenges the structures and processes…

  13. Characterization of limestone reacted with acid-mine drainage in a pulsed limestone bed treatment system at the Friendship Hill National Historical Site, Pennsylvania, USA

    Science.gov (United States)

    Hammarstrom, J.M.; Sibrell, P.L.; Belkin, H.E.

    2003-01-01

    Armoring of limestone is a common cause of failure in limestone-based acid-mine drainage (AMD) treatment systems. Limestone is the least expensive material available for acid neutralization, but is not typically recommended for highly acidic, Fe-rich waters due to armoring with Fe(III) oxyhydroxide coatings. A new AMD treatment technology that uses CO2 in a pulsed limestone bed reactor minimizes armor formation and enhances limestone reaction with AMD. Limestone was characterized before and after treatment with constant flow and with the new pulsed limestone bed process using AMD from an inactive coal mine in Pennsylvania (pH = 2.9, Fe = 150 mg/l, acidity = 1000 mg/l CaCO3). In constant flow experiments, limestone is completely armored with reddish-colored ochre within 48 h of contact in a fluidized bed reactor. Effluent pH initially increased from the inflow pH of 2.9 to over 7, but then decreased to 6 during operation. Limestone removed from a pulsed bed pilot plant is a mixture of unarmored, rounded and etched limestone grains and partially armored limestone and refractory mineral grains (dolomite, pyrite). The ???30% of the residual grains in the pulsed flow reactor that are armored have thicker (50- to 100-??m), more aluminous coatings and lack the gypsum rind that develops in the constant flow experiment. Aluminium-rich zones developed in the interior parts of armor rims in both the constant flow and pulsed limestone bed experiments in response to pH changes at the solid/solution interface. ?? 2003 Elsevier Ltd. All rights reserved.

  14. Residual stresses

    International Nuclear Information System (INIS)

    Sahotra, I.M.

    2006-01-01

    The principal effect of unloading a material strained into the plastic range is to create a permanent set (plastic deformation), which if restricted somehow, gives rise to a system of self-balancing within the same member or reaction balanced by other members of the structure., known as residual stresses. These stresses stay there as locked-in stresses, in the body or a part of it in the absence of any external loading. Residual stresses are induced during hot-rolling and welding differential cooling, cold-forming and extruding: cold straightening and spot heating, fabrication and forced fitting of components constraining the structure to a particular geometry. The areas which cool more quickly develop residual compressive stresses, while the slower cooling areas develop residual tensile stresses, and a self-balancing or reaction balanced system of residual stresses is formed. The phenomenon of residual stresses is the most challenging in its application in surface modification techniques determining endurance mechanism against fracture and fatigue failures. This paper discusses the mechanism of residual stresses, that how the residual stresses are fanned and what their behavior is under the action of external forces. Such as in the case of a circular bar under limit torque, rectangular beam under limt moment, reclaiming of shafts welds and peening etc. (author)

  15. Organic residue, limestone, gypsum, and phosphorus adsorption by lowland soils Resíduo orgânico, calcário e gesso e a adsorção de fósforo por solos de várzea

    Directory of Open Access Journals (Sweden)

    Alex Teixeira Andrade

    2002-06-01

    Full Text Available Organic residue application is a low cost alternative to reduce the use of inorganic fertilizers and correctives. In order to study the effect of organic residues, limestone and gypsum application on phosphorus adsorption by lowland soils, four experiments were carried out. A Mesic Organosol (OY, a Melanic Gleysol (MG, a Haplic Gleysol (GX, and a Fluvic Neosol (RU were used in a completely randomized design and factorial scheme (3 x 2, with five replicates: three soil amendment practices (limestone, gypsum and no corrective and two levels of organic residue (with and without corral manure. Soil samples were incubated for 60 days, with and without organic residue incorporation. After this period, we applied the corrective and incubated the soil for 30 days, then P and basic fertilization (macro and micronutrients were applied and the soil was incubated for additional 60 days. Equilibrium phosphorus, maximum phosphate adsorption capacity, pH, exchangeable Al and phosphorus-buffering index were measured. Organic residue and limestone application increased soil pH and reduced exchangeable Al, decreasing P adsorption. Gypsum application did not increase the pH but reduced exchangeable Al and P adsorption.A aplicação de resíduo orgânico é uma alternativa de baixo custo para reduzir a aplicação de fertilizantes inorgânicos e corretivos. Com objetivo de estudar a relação da aplicação de resíduo orgânico, calcário e gesso com adsorção de fósforo em solos de várzea conduziram-se simultaneamente quatro experimentos com os solos Organossolo Mésico (OY, Gleissolo Melânico (GM, Gleissolo Háplico (GX e Neossolo Flúvico (RU. O delineamento experimental utilizado foi o inteiramente casualizado, em esquema fatorial 3x2, com cinco repetições, sendo três práticas de correção do solo (calcário, gesso e sem corretivo e dois níveis de resíduo orgânico com e sem esterco de curral curtido. Amostras dos solos foram incubadas por 60 dias

  16. Limestone valib eetilisi firmasid / Virge Lahe

    Index Scriptorium Estoniae

    Lahe, Virge

    2008-01-01

    Endised Hansapanga investeerimisfondide analüütikud hakkavad läbi Limestone fondide pakkuma sotsiaalselt vastutustundlikku investeerimist (Socially Responsible Investing). Kommenteerivad Art Lukas ja Silver Vohu. Vt. samas: Limestone Investment Management AS

  17. CALCIUM CARBONATE DISSOLUTION RATE IN LIMESTONE CONTACTORS

    Science.gov (United States)

    The rate of carbonate mineral dissolution from limestone was studied using a rotating disk apparatus and samples of limestone of varied composition. The purpose of this study was to determine the effect of limestone composition on the kinetics of carbonate mineral dissolution. Th...

  18. Assessment of the Possibility of Using Reclaimed Materials for Making Cores by the Blowing Method

    Directory of Open Access Journals (Sweden)

    Dańko R.

    2017-03-01

    Full Text Available The cumulative results of investigations of the possibility of using the reclaimed materials after the mechanical, thermal or mechanical-thermal reclamation for making cores by means of the blowing method in the alkaline CO2 technology, are presented in the paper. Three kinds of spent sands: with furfuryl resin, bentonite and alkaline phenolic resin, obtained from the foundry, were subjected to three kinds of reclamation: mechanical, thermal and combined mechanical-thermal, applying for this aim adequate experimental devices. The obtained reclaims were assessed with regard to the degree of the matrix liberation from the determined binding material. Reclaims of moulding sands with binders of the form of resin were assessed with regard to ignition loss values and pH reaction, while reclaims of moulding sands with bentonite with regard to the residual clay content and pH value. In all cases the results of the performed sieve analyses were estimated and the average characteristic diameter dl was determined. The reclaimed matrix was applied as a full substitute of the fresh high-silica sand in typical procedures of preparing core sands used for making shaped samples for bending strength investigations, Rgu.

  19. Novel Hydroxyapatite Coatings for the Conservation of Marble and Limestone

    Science.gov (United States)

    Naidu, Sonia

    Marble and limestone are calcite-based materials used in the construction of various structures, many of which have significant artistic and architectural value. Unfortunately, due to calcite's high dissolution rate, these stones are susceptible to chemically-induced weathering in nature. Limestone, due to its inherent porosity, also faces other environmental weathering processes that cause weakening from disintegration at grain boundaries. The treatments presently available are all deficient in one way or another. The aim of this work is to examine the feasibility of using hydroxyapatite (HAP) as a novel protective coating for marble and limestone, with two goals: i) to reduce acid corrosion of marble and ii) to consolidate physically weathered limestone. The motivation for using HAP is its low dissolution rate and structural compatibility with calcite. Mild, wet chemical synthesis routes, in which inorganic phosphate-based solutions were reacted with marble and limestone, alone and with other precursors, were used to produce HAP films. Film nucleation, growth and phase evolution were studied on marble to understand film formation and determine the optimal synthesis route. An acid resistance test was developed to investigate the attack mechanism on marble and quantify the efficacy of HAP-based coatings. Film nucleation and growth were dependent on substrate surface roughness and increased with calcium and carbonate salt additions during synthesis. Acid attack on marble occurred via simultaneous dissolution at grain boundaries, twin boundaries and grain surfaces. HAP provided intermediate protection against acid attack, when compared to two conventional treatments. Its ability to protect the stone from acid was not as significant as predicted from dissolution kinetics and this was attributed to incomplete coverage and residual porosity within the film, arising from its flake-like crystal growth habit, which enabled acid to access the underlying substrate. The

  20. Sustainability of Water Reclamation: Long-Term Recharge with Reclaimed Wastewater Does Not Enhance Antibiotic Resistance in Sediment Bacteria

    Directory of Open Access Journals (Sweden)

    Jean E. McLain

    2014-03-01

    Full Text Available Wastewater reclamation for municipal irrigation is an increasingly attractive option for extending water supplies. However, public health concerns include the potential for development of antibiotic resistance (AR in environmental bacteria after exposure to residual pharmaceuticals in reclaimed water. Though scientific studies have reported high levels of AR in soils irrigated with wastewater, these works often fail to address the soil resistome, or the natural occurrence of AR. This study compared AR patterns in sediment Enterococcus isolated from water storage basins containing either reclaimed water or groundwater in central Arizona. Resistance to 16 antibiotics was quantified in isolates to a depth of 30 cm. Results reveal high levels of resistance to certain antibiotics, including lincomycin, ciprofloxacin, and erythromycin, exists in sediments regardless of the water source (groundwater, reclaimed water, and higher AR was not detectable in reclaimed water sediments. Furthermore, multiple-antibiotic-resistance (MAR was substantially reduced in isolates from reclaimed water sediments, compared to freshwater sediment isolates. Comparing the development of AR in sediment bacteria at these two sites will increase awareness of the environmental and public health impacts of using reclaimed water for irrigation of municipal areas, and illustrates the necessity for control sites in studies examining AR development in environmental microbiota.

  1. Reclaiming unused IPv4 addresses

    CERN Multimedia

    IT Department

    2016-01-01

    As many people might know, the number of IPv4 addresses is limited and almost all have been allocated (see here and here for more information).   Although CERN has been allocated some 340,000 addresses, the way these are allocated across the site is not as efficient as we would like. As we face an increasing demand for IPv4 addresses with the growth in virtual machines, the IT Department’s Communication Systems Group will be reorganising address allocation during 2016 to make more efficient use of the IPv4 address ranges that have been allocated to CERN. We aim, wherever possible, to avoid giving out fixed IP addresses, and have all devices connected to the campus network obtain an address dynamically each time they connect. As a first stage, starting in February, IP addresses that have not been used for more than 9 months will be reclaimed. No information about the devices concerned will be deleted from LANDB, but a new IP address will have to be requested if they are ever reconnected to t...

  2. Refrigeration Playbook. Heat Reclaim; Optimizing Heat Rejection and Refrigeration Heat Reclaim for Supermarket Energy Conservation

    Energy Technology Data Exchange (ETDEWEB)

    Reis, Chuck [CTA Architects Engineers, Boise, ID (United States); Nelson, Eric [CTA Architects Engineers, Boise, ID (United States); Armer, James [CTA Architects Engineers, Boise, ID (United States); Johnson, Tim [CTA Architects Engineers, Boise, ID (United States); Hirsch, Adam [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Doebber, Ian [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2015-03-01

    The purpose of this playbook and accompanying spreadsheets is to generalize the detailed CBP analysis and to put tools in the hands of experienced refrigeration designers to evaluate multiple applications of refrigeration waste heat reclaim across the United States. Supermarkets with large portfolios of similar buildings can use these tools to assess the impact of large-scale implementation of heat reclaim systems. In addition, the playbook provides best practices for implementing heat reclaim systems to achieve the best long-term performance possible. It includes guidance on operations and maintenance as well as measurement and verification.

  3. Adsorption of anionic surfactants in limestone medium during oil recovery

    Energy Technology Data Exchange (ETDEWEB)

    Canbolat, Serhat; Bagci, Suat [Middle East Technical Univ., Dept. of Petroleum and Natural Gas Engineering, Ankara (Turkey)

    2004-07-15

    Foam-forming surfactant performance was evaluated by several experimental methods (interfacial tension, foam stability, corefloods) using commercial surfactants. There is considerable interest in the use of foam-forming surfactants for mobility control in water flood. To provide effective mobility control, the injected surfactant must propagate from the injection well toward the production well. One of the important parameters affecting propagation of foam-forming surfactant through the reservoir is the retention of surfactant due to its adsorption on reservoir rock. The determination of the adsorption of foam-forming surfactants in limestone reservoirs is important for the residual oil recovery efficiency. Adsorption measurements, recovery efficiencies, and surfactant and alkaline flooding experiments carried out with the representative of the selected surfactants alkaline solutions, linear alkyl benzene sulphonic acid (LABSA), sodium lauryl ether sulfate (SLES), and NaOH in a limestone medium. These surfactants were selected with respect to their foaming ability. Calibration curves formed by pH measurements were used to determine the correct adsorption amount of the used surfactants and recovery efficiency of these surfactants compared with base waterflooding. The results showed that LABSA adsorbed more than SLES in limestone reservoirs. The recovery efficiency of SLES was higher than the recovery efficiency of LABSA, and they decreased the recovery efficiency with respect to only the water injection case. (Author)

  4. [Ecological risks of reclaimed water irrigation: a review].

    Science.gov (United States)

    Chen, Wei-Ping; Zhang, Wei-Ling; Pan, Neng; Jiao, Wen-Tao

    2012-12-01

    Wastewater reclamation and reuse have become an important approach to alleviate the water crisis in China because of its social, economic and ecological benefits. The irrigation on urban green space and farmland is the primary utilization of reclaimed water, which has been practiced world widely. To understand the risk of reclaimed water irrigation, we summarized and reviewed the publications associated with typical pollutants in reclaimed water including salts, nitrogen, heavy metals, emerging pollutants and pathogens, systematically analyzed the ecological risk posed by reclaimed water irrigation regarding plant growth, groundwater quality and public health. Studies showed that salt and salt ions were the major risk sources of reclaimed water irrigation, spreading disease was another potential risk of using reclaimed water, and emerging pollutants was the hot topic in researches of ecological risk. Based on overseas experiences, risk control measures on reclaimed water irrigation in urban green space and farmland were proposed. Five recommendations were given to promote the safe use of reclaimed water irrigation including (1) strengthen long-term in situ monitoring, (2) promote the modeling studies, (3) build up the connections of reclaimed water quality, irrigation management and ecological risk, (4) evaluate the soil bearing capacity of reclaimed water irrigation, (5) and establish risk management system of reclaimed water reuse.

  5. An overview of reclaimed water reuse in China.

    Science.gov (United States)

    Yi, Lili; Jiao, Wentao; Chen, Xiaoning; Chen, Weiping

    2011-01-01

    China is facing severe water problems including scarcity and pollution which are now becoming key factors restricting developments. Creating an alternative water resource and reducing effluent discharges, water reuse has been recognized as an integral part of water and wastewater management scheme in China. The government has launched nationwide efforts to optimize the benefits of utilizing reclaimed water. This article reviewed the water reuse activities in China, including: (1) application history and current status; (2) potentials of reclaimed water reuse; (3) laws, policies and regulations governing reclaimed water reuse; (4) risks associated with reclaimed water reuse; (5) issues in reclaimed water reuse. Reclaimed water in Beijing and Tianjin were given as examples. Suggestions for improving the efficiencies of reusing urban wastewater were advanced. Being the largest user of reclaimed wastewater in the world, China's experience can benefit the development of water reuse in other regions.

  6. Bacterial community composition in reclaimed and unreclaimed ...

    African Journals Online (AJOL)

    An investigation was conducted to compare the microbial community structures between contaminated and reclaimed mine tailings of Dexing copper mine, Jiangxi province, China. Sample T1 was obtained from tailings site, where reclamation of phytostabilization has been conducted for 20 years successfully whereas, the ...

  7. Effects of reclaimed water matrix on fate of pharmaceuticals and personal care products in soil.

    Science.gov (United States)

    Dodgen, L K; Zheng, W

    2016-08-01

    Reclaimed water is increasingly used to supplement water resources. However, reclaimed water has a complex matrix, which includes emerging chemical contaminants, that is introduced to the soil when this water is used for irrigation. The effects of microbial activity, dissolved matter, nutrients, and particulate matter in reclaimed water on half-life of 11 pharmaceutical and personal care products (PPCPs) in soil were investigated with 7 treatment waters, namely swine lagoon effluent (either unaltered, sterilized, or filtered and sterilized) and nanopure water (either unaltered or with added nitrogen, phosphorus, or potassium). The extractable residues of the parent PPCPs were measured over 35 d. Lagoon microbial activity was significantly (p ≤ 0.05) related to increased half-life of 4 PPCPs (carbamazepine, fluoxetine, ibuprofen, sulfamethoxazole) by 14-74%, and to decreased half-life of 3 others (caffeine, gemfibrozil, naproxen) by 13-25%. The presence of lagoon dissolved matter was significantly correlated with a 20-110% increase in half-life for 6 PPCPs (caffeine, estrone, gemfibrozil, ibuprofen, naproxen, triclocarban). However, lagoon particulate matter was significantly correlated with 9-52% decrease in half-life for these same compounds, as well as trimethoprim. The levels of nitrogen, phosphorous, and potassium in the lagoon effluent were not significantly related to half-life for most PPCPs, except caffeine. Overall, specific components of reclaimed water matrix had different effects on the soil half-lives of PPCPs, suggesting that the composition of reclaimed water needs to be considered when evaluating PPCP fate after land application. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. Ozonization of reclaimed wastewater and effects on particulate matter and disinfection. Reuse perspectives for irrigation in Tenerife (Spain); Ozonizacion del agua residual depurada y sus efectos sobre la materia particulada y desinfeccion. Perspectivas para su posterior uso en el riego agricola en Tenerife

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez Gomez, L. E.; Diaz Gonzalez, F.; Abreu Acosta, N.; Martin Delgado, M.; Aguilar Gonzalez, E.

    2006-07-01

    In this work a study on the feasibility of ozonization as a disinfection and organic matter removal method was carried out on reclaimed wastewater for crop irrigation in the South of Tenerife. three different O{sub 3} doses were applied to reclaimed wastewater: 10, 15 and 20 g/m''3. The highest total suspended solids (TSS) removal obtained was 44%, with both 15 and 20 mg/l O{sub 3}. However, a direct relationship between the O{sub 3} dose applied and the reduction of faecal coliforms has been found, achieving a complete removal with the O{sub 3} dose of 20 mg/l. (Author) 17 refs.

  9. The behavior limestone under explosive load

    Science.gov (United States)

    Orlov, M. Yu; Orlova, Yu N.; Bogomolov, G. N.

    2016-11-01

    Limestone behavior under explosive loading was investigated. The behavior of the limestone by the action of the three types of explosives, including granular, ammonite and emulsion explosives was studied in detail. The shape and diameter of the explosion craters were obtained. The observed fragments after the blast have been classified as large, medium and small fragments. Three full-scale experiments were carried out. The research results can be used as a qualitative test for the approbation of numerical methods.

  10. About the use and treatment of reclaimed wastewater

    International Nuclear Information System (INIS)

    Marin Galvin, R.

    2009-01-01

    Demand of water in our actual society is increasing each day. Taking into account the irregular climatic situation experienced in a lot of zones of Spain, it is necessary to use all the available resources. Among the conventional resources of sweet waters (surface and underground), we must pay attention to the desalted waters and to the reclaimed wastewater. In this way, the practical use of reclaimed wastewater must be supported in three basic items: normative about reusing of reclaimed wastewater, that of treated wastewater and effluents discarded to natural environment and finally, treatment processes to reclaim wastewater. (Author) 11 refs

  11. Grizzly bear diet shifting on reclaimed mines

    Directory of Open Access Journals (Sweden)

    Bogdan Cristescu

    2015-07-01

    Full Text Available Industrial developments and reclamation change habitat, possibly altering large carnivore food base. We monitored the diet of a low-density population of grizzly bears occupying a landscape with open-pit coal mines in Canada. During 2009–2010 we instrumented 10 bears with GPS radiocollars and compared their feeding on reclaimed coal mines and neighboring Rocky Mountains and their foothills. In addition, we compared our data with historical bear diet for the same population collected in 2001–2003, before extensive mine reclamation occurred. Diet on mines (n=331 scats was dominated by non-native forbs and graminoids, while diets in the Foothills and Mountains consisted primarily of ungulates and Hedysarum spp. roots respectively, showing diet shifting with availability. Field visitation of feeding sites (n=234 GPS relocation clusters also showed that ungulates were the main diet component in the Foothills, whereas on reclaimed mines bears were least carnivorous. These differences illustrate a shift to feeding on non-native forbs while comparisons with historical diet reveal emergence of elk as an important bear food. Food resources on reclaimed mines attract bears from wilderness areas and bears may be more adaptable to landscape change than previously thought. The grizzly bear’s ready use of mines cautions the universal view of this species as umbrella indicative of biodiversity.

  12. Reaction between Hydrogen Sulfide and Limestone Calcines

    Czech Academy of Sciences Publication Activity Database

    Hartman, Miloslav; Svoboda, Karel; Trnka, Otakar; Čermák, Jiří

    2002-01-01

    Roč. 41, č. 10 (2002), s. 2392-2398 ISSN 0888-5885 R&D Projects: GA AV ČR IAA4072711; GA AV ČR IAA4072801 Keywords : hydrogen sulfide * limestone calcines * desulfurization Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 1.247, year: 2002

  13. Hydrogen Chloride Reaction with Lime and Limestone

    DEFF Research Database (Denmark)

    Erik Weinell, Claus; Jensen, Peter I.; Dam-Johansen, Kim

    1992-01-01

    The capacity of solid slaked lime and limestone for binding HCl from a gas phase has been investigated in the temperature range 60-1000 °C. The binding capacity is largest in the range 500-600 °C. However, for slaked lime in the presence of water, a large binding capacity is observed also below 150...

  14. Neutron activation analysis of limestone objects

    International Nuclear Information System (INIS)

    Meyers, P.; Van Zelst, L.

    1977-01-01

    The elemental composition of samples from limestone objects were determined by neutron activation analysis to investigate whether this technique can be used to distinguish between objects made of limestone from different sources. Samples weighing between 0.2-2 grams were obtained by drilling from a series of ancient Egyptian and medieval Spanish objects. Analysis was performed on aliquots varying in weight from 40-100 milligrams. The following elements were determined quantitatively: Na, K, Rb, Cs, Ba, Sc, La, Ce, Sm, Eu, Hf, Th, Ta, Cr, Mn, Fe, Co and Zn. The data on Egyptian limestones indicate that, because of the inhomogeneous nature of the stone, 0.2-2 gram samples may not be representative of an entire object. Nevertheless, multivariate statistical methods produced a clear distinction between objects originating from the Luxor area (ancient Thebes) and objects found north of Luxor. The Spanish limestone studied appeared to be more homogeneous. Samples from stylistically related objects have similar elemental compositions while relative large differences were observed between objects having no relationship other than the common provenance of medieval Spain. (orig.) [de

  15. Influência de esterco bovino e calcário sobre o efeito residual da adubação fosfatada para a Brachiaria brizantha cultivada após o feijoeiro Influence of cattle manure and limestone on residual effects of phosphorus fertilizer in Brachiaria brizantha grown after common bean

    Directory of Open Access Journals (Sweden)

    Renato Ferreira de Souza

    2010-02-01

    Full Text Available A deficiência de P é uma das limitações mais generalizadas ao estabelecimento e à manutenção de pastagens nas regiões tropicais. Essa deficiência é devida, principalmente, ao baixo teor e aos processos de adsorção/precipitação do P nos solos. Com o objetivo de avaliar a influência da calagem e da adubação orgânica sobre o efeito residual do P, aplicado ao feijoeiro, na nutrição fosfatada e no rendimento do braquiarão cultivado em sucessão, foram conduzidos, em casa de vegetação, quatro experimentos inteiramente ao acaso, em esquema fatorial 4 x 5 e três repetições. Cada unidade experimental foi constituída por um vaso contendo 4 dm³ dos solos: Latossolo Vermelho distrófico textura muito argilosa, Latossolo Vermelho-Amarelo distrófico textura argilosa, Latossolo Vermelho-Amarelo distrófico textura média e Neossolo Quartzarênico órtico textura arenosa. Cada solo, representando um experimento, recebeu os tratamentos constituídos de quatro doses de calcário (0,0; 0,5; 1,0; e 2,0 vezes a dose recomendada para elevar a saturação por bases a 60 % e cinco doses de esterco bovino (0,0; 2,5; 5,0; 7,5; e 10,0 % do volume de solo. Os vasos foram cultivados com feijoeiro e, após a colheita deste, cultivaram-se três plantas de braquiarão, as quais foram submetidas a cortes consecutivos aos 70, 160 e 290 dias após a emergência. As produções totais de matéria seca e o acúmulo de P na parte aérea do braquiarão foram positivamente influenciados pela adubação orgânica e pela calagem. Esses tratamentos também influenciaram positivamente o efeito residual da adubação fosfatada, aplicada ao feijoeiro, na nutrição fosfatada e no rendimento do braquiarão.Phosphorus (P deficiency is one of the most widespread limitations to the establishment and maintenance of pastures in tropical areas. This deficiency is mainly due to the low soil P content and adsorption/precipitation processes. The purpose of this study was

  16. The use of Limestone Powder as an Alternative Cement Replacement

    African Journals Online (AJOL)

    user

    focused on the effects of limestone on the cement ... construction materials in Ethiopia is increasing .... Findings of research works on the strength reveals ... This CEN standard sand is delivered ... control mix made without limestone fines.

  17. Kinetic Study of Calcination of Jakura Limestone Using Power Rate ...

    African Journals Online (AJOL)

    National Research Institute for Chemical Technology, P.M. B 1052, Zaria, ... calcination of Jakura limestone was also found to be first order reaction with respect to CaCO3 ... Keywords: Jakura, limestone, calcination, kinetics, power law model.

  18. Effect of limestone particle size on bone quality characteristics of ...

    African Journals Online (AJOL)

    A study was conducted to determine the effect of different limestone particle sizes in layer diets on bone quality characteristics at end-of-lay hens. Calcitic limestone (360 g Ca/kg DM) that is extensively used in commercial poultry diets was obtained from a specific South African source. Limestone particles were graded as ...

  19. Terrestrial salamander abundance on reclaimed mountaintop removal mines

    Science.gov (United States)

    Wood, Petra Bohall; Williams, Jennifer M.

    2013-01-01

    Mountaintop removal mining, a large-scale disturbance affecting vegetation, soil structure, and topography, converts landscapes from mature forests to extensive grassland and shrubland habitats. We sampled salamanders using drift-fence arrays and coverboard transects on and near mountaintop removal mines in southern West Virginia, USA, during 2000–2002. We compared terrestrial salamander relative abundance and species richness of un-mined, intact forest with habitats on reclaimed mountaintop removal mines (reclaimed grassland, reclaimed shrubland, and fragmented forest). Salamanders within forests increased in relative abundance with increasing distance from reclaimed mine edge. Reclaimed grassland and shrubland habitats had lower relative abundance and species richness than forests. Characteristics of reclaimed habitats that likely contributed to lower salamander abundance included poor soils (dry, compacted, little organic matter, high rock content), reduced vertical structure of vegetation and little tree cover, and low litter and woody debris cover. Past research has shown that salamander populations reduced by clearcutting may rebound in 15–24 years. Time since disturbance was 7–28 years in reclaimed habitats on our study areas and salamander populations had not reached levels found in adjacent mature forests.

  20. Colmenar limestone as a resource for built heritage

    Science.gov (United States)

    Fort, Rafael; Álvarez de Buergo, Mónica; Varas-Muriel, MªJosé; Mercedes Pérez-Monserrat, Elena

    2013-04-01

    The Colmenar stone (or Colmenar limestone) has been used in the construction of significant builidings of the Central area of Spain, such as the Royal Palace of Aranjuez (16th -18th centuries) or the Royal Palace of Madrid (18th century). Nowadays this building stone is still widely used, both for new construction and restoration works, as well as for the indoor ornamentation of emblematic buildings such as the Royal Theater of Madrid (20th century). There are many quarries from where this stone was exploited, being the most prestigious ones those located in Colmenar de Oreja, at 50 km Southeast the city of Madrid. The high quality of the stone in these quarries, its whiteness and pureness, made this locality the most relevant in these stonés extractive activities, concentrating the most relevant exploitations and providing the stone the denomination of the municipality (Colmenar). It was an underground mining extraction until the 20th century in order to reach the highest quality level of the mine, the so called "Banco Gordo" (Thick Bank). Generically known as moorland limestone, this rock belongs to the fluvial-lacustrine carbonates of the Upper Miocene Unit of the Tertiary Madrid's Basin. Its tonality mainly ranges from white to cream and even light grey. Under a petrographic point of view, this limestone is constituted by 40% of bioclasts (characea, ostracods and gasteropods), 20-30% of micritic matrix and 30-40% of sparitic cement. Therefore, it can be classified as a biomicrite/biosparite limestone or as a bioclastic packstone. Some particularities of these limestones regarding their appearance are related to some karstic processes they underwent linked to some dissolution phenomena during the Pliocene. All of this resulted on an abundance of cavities with terra rossa fillings, a non-soluble clayey residue, iron enriched, which is the responsible for the reddish and pinkish color that the Colmenar stone sometimes shows. These petrographic characteristics

  1. Face logging in Copenhagen Limestone, Denmark

    DEFF Research Database (Denmark)

    Jakobsen, Lisa; Foged, Niels Nielsen; Erichsen, Lars

    2015-01-01

    tunnel in Copenhagen more than 2.5 km face logs were made in 467 locations at underground stations, shafts, caverns and along bored tunnels. Over 160 geotechnical boreholes, many with geophysical logging were executed prior to construction works. The bedrock consists of Paleogene "Copenhagen limestone......The requirement for excavation support can be assessed from face logging. Face logs can also improve our knowledge of lithological and structural conditions within bedrock and supplement information from boreholes and geophysical logs. During the construction of 8 km metro tunnel and 4 km heating....... The induration degrees recorded in face logs and boreholes are compared and correlated. Distinct geophysical log markers are used to divide the limestone into three units. These marker horizons are correlated between face logs and geotechnical boreholes. A 3D model of the strength variations recorded within...

  2. Effects of phosphate limestone on structure and quality under sugarcane vertisoles

    Directory of Open Access Journals (Sweden)

    Pedro Cairo Cairo

    2017-10-01

    Full Text Available The work was developed in sugarcane areas of cuban vertisols of the north coast of the province of Villa Clara municipality of Sagua la Grande, with the aim of evaluating the effectiveness of phosphate limestone and their combinations with fertilizers and organic manure on the structure and quality of vertisols under sugarcane cultivation. An experiment with phosphate limestone levels and combinations with organic manure (compost, filter cake and fertilizers (NPK was carried out on a wasstrip-block design. A soil analysis was performedat the depth of 0-20 and 20 -40 cm 36 months after the application of treatments. Organic matter, stable aggregates, factor structure, permeability, T value, exchangeable cations, index soil quality and productivity of sugarcane were evaluated. Phosphate limestone and there combinations with organic manures manifested significant effects on soil structure both in the surface layer and subsurface with residual impact over time to 36 months. The results show the close relationship between phosphate limestone and there combinations with organic manures on soil quality index additive, yield of sugarcane and economic impact.

  3. Plant Guide: Limestone hawksbeard: Crepis intermedia

    Science.gov (United States)

    L. St. John; D. Tilley

    2012-01-01

    Sunflower family (Asteraceae). Limestone hawksbeard is a native perennial forb with one or two stems arising from a taproot. Plants are 30-70cm tall and basal leaves are 10-40 cm long, pinnatifid, with a fairly broad, undivided midstrip and entire or dentate segments. Plants are densely or sparsely gray-tomentulose. There are 10-60 heads per plant that are 7-12...

  4. Limestone quarrying and quarry reclamation in Britain

    Science.gov (United States)

    Gunn, J.; Bailey, D.

    1993-06-01

    Limestones have been worked for many thousands of years — initially for building stone and agricultural lime and more recently for a wide range of construction and industrial uses. In most industrialized countries limestone quarries represent the most visually obvious and, in both process and landform terms, the most dramatic anthropogenic impact on karst terrain. However, quarrying has, to date, received surprisingly little attention from karst scientists. Research in the English Peak District suggested that the postexcavation evolution of quarried limestone rock faces was in part a result of the methods used in their excavation, and this led to the development of a technique designed to reduce the visual and environmental impacts of modern quarries by “Landform replication. ” This involves the use of controlled “restoration blasting” techniques on quarried rock slopes to construct a landform sequence similar to that in the surrounding natural landscape. The constructed landforms are then partially revegetated using appropriate wildflower, grass, and/or tree species.

  5. Reclaimable Thermally Reversible Polymers for AM Feedstock, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — CRG proposes to continue efforts from the 2016 NASA SBIR Phase I topic H5.04 Reclaimable Thermally Reversible Polymers for AM Feedstock. In Phase II, CRG will refine...

  6. Cost Analysis of NEDU’s Helium Reclaimer.

    Science.gov (United States)

    1981-09-01

    T ITLE (and Subtitle) S . TYPE OF REPORT 6 PERIOD COVERED COST ANALYSIS OF NEDU’S HELIUM RECLAIMER . Survey 6 . PERFORMING ORG. REPORT NUMSER 7...telephone conversation). 5. Charles T. Horngren , "Introduction tu Management Accounting " Fourth Edition. 3 . .4m mmnssmmlm~ • FIGURE 1 PRESENT, FUTURE AND...FEET COST OF PERIODIC MAINTENANCE OF HELIUM ELECTRIiC COST COST OF TOTAL RECLAIMED POWER NEW COST PRESENT WORTH YEAR N PER YEAR ( S /1000 FT

  7. Impact of reclaimed water irrigation on antibiotic resistance in public parks, Beijing, China

    International Nuclear Information System (INIS)

    Wang, Feng-Hua; Qiao, Min; Lv, Zhen-E; Guo, Guang-Xia; Jia, Yan; Su, Yu-Hong; Zhu, Yong-Guan

    2014-01-01

    The abundance and distribution of antibiotics and antibiotic resistance genes (ARGs) in soils from six parks using reclaimed water in Beijing, China, were characterized. Three classes of commonly used antibiotics (tetracycles, quinolones, and sulfonamides) were analyzed by liquid chromatography-tandem mass spectrometry (LC-MS/MS). The highest concentrations of tetracyclines and quinolones were 145.2 μg kg −1 and 79.2 μg kg −1 , respectively. Detected tetG, tetW, sulI, and sulII genes were quantified by quantitative PCR. ARGs exhibited various abundances for different park soils. The integrase gene (intI1) as an indicator of horizontal gene transfer potential was also detected in high abundance, and had significant positive correlation with tetG, sulI, and sulII genes, suggesting that intI1 may be involved in ARGs dissemination. Both sulII and intI1 clones had high homology with some classes of pathogenic bacteria, such as Klebsiella oxytoca, Acinetobacter baumannii, Shigella flexneri, which could trigger potential public health concern. Highlights: • Reclaimed water irrigation could increase the concentration of antibiotics and ARGs in urban park soils. • ARGs can be persistent in the irrigated park soils, even without antibiotic selection pressure. • Both sulII and intI1 clones had high homology with some classes of pathogenic bacteria. -- The release of residual antibiotics and ARGs from reclaimed water could result in the proliferation of ARGs in irrigated park soils

  8. Regrowth of potential opportunistic pathogens and algae in reclaimed-water distribution systems.

    Science.gov (United States)

    Jjemba, Patrick K; Weinrich, Lauren A; Cheng, Wei; Giraldo, Eugenio; Lechevallier, Mark W

    2010-07-01

    A study of the quality of reclaimed water in treated effluent, after storage, and at three points in the distribution system of four plants in California, Florida, Massachusetts, and New York was conducted for 1 year. The plants had different treatment processes (conventional versus membrane bioreactor), production capacities, and methods for storage of the water, and the intended end uses of the water were different. The analysis focused on the occurrence of indicator bacteria (heterotrophic bacteria, coliforms, Escherichia coli, and enterococci) and opportunistic pathogens (Aeromonas spp., enteropathogenic E. coli O157:H7, Legionella spp., Mycobacterium spp., and Pseudomonas spp.), as well as algae. Using immunological methods, E. coli O157:H7 was detected in the effluent of only one system, but it was not detected at the sampling points, suggesting that its survival in the system was poor. Although all of the treatment systems effectively reduced the levels of bacteria in the effluent, bacteria regrew in the reservoir and distribution systems because of the loss of residual disinfectant and high assimilable organic carbon levels. In the systems with open reservoirs, algal growth reduced the water quality by increasing the turbidity and accumulating at the end of the distribution system. Opportunistic pathogens, notably Aeromonas, Legionella, Mycobacterium, and Pseudomonas, occurred more frequently than indicator bacteria (enterococci, coliforms, and E. coli). The Mycobacterium spp. were very diverse and occurred most frequently in membrane bioreactor systems, and Mycobacterium cookii was identified more often than the other species. The public health risk associated with these opportunistic pathogens in reclaimed water is unknown. Collectively, our results show the need to develop best management practices for reclaimed water to control bacterial regrowth and degradation of water before it is utilized at the point of use.

  9. Regrowth of Potential Opportunistic Pathogens and Algae in Reclaimed-Water Distribution Systems ▿

    Science.gov (United States)

    Jjemba, Patrick K.; Weinrich, Lauren A.; Cheng, Wei; Giraldo, Eugenio; LeChevallier, Mark W.

    2010-01-01

    A study of the quality of reclaimed water in treated effluent, after storage, and at three points in the distribution system of four plants in California, Florida, Massachusetts, and New York was conducted for 1 year. The plants had different treatment processes (conventional versus membrane bioreactor), production capacities, and methods for storage of the water, and the intended end uses of the water were different. The analysis focused on the occurrence of indicator bacteria (heterotrophic bacteria, coliforms, Escherichia coli, and enterococci) and opportunistic pathogens (Aeromonas spp., enteropathogenic E. coli O157:H7, Legionella spp., Mycobacterium spp., and Pseudomonas spp.), as well as algae. Using immunological methods, E. coli O157:H7 was detected in the effluent of only one system, but it was not detected at the sampling points, suggesting that its survival in the system was poor. Although all of the treatment systems effectively reduced the levels of bacteria in the effluent, bacteria regrew in the reservoir and distribution systems because of the loss of residual disinfectant and high assimilable organic carbon levels. In the systems with open reservoirs, algal growth reduced the water quality by increasing the turbidity and accumulating at the end of the distribution system. Opportunistic pathogens, notably Aeromonas, Legionella, Mycobacterium, and Pseudomonas, occurred more frequently than indicator bacteria (enterococci, coliforms, and E. coli). The Mycobacterium spp. were very diverse and occurred most frequently in membrane bioreactor systems, and Mycobacterium cookii was identified more often than the other species. The public health risk associated with these opportunistic pathogens in reclaimed water is unknown. Collectively, our results show the need to develop best management practices for reclaimed water to control bacterial regrowth and degradation of water before it is utilized at the point of use. PMID:20453149

  10. Rock mass characterization for tunnels in the Copenhagen limestone

    DEFF Research Database (Denmark)

    Foged, Niels Nielsen; Jakobsen, Lisa; Jackson, Peter

    2007-01-01

    Tunnels in Copenhagen are drilled through highly anisotropic limestone comprising alternating strongly lithified and less lithified parts. The mass quality of the limestone is usually defined from fracture spacing registered in core samples. The deposit is, however, affected destructively by dril...... by drilling activity yielding a low Rock Quality Designation RQD. In-situ observations of the limestone in excavations or televiewer logs reveal only few natural discontinuities compared to core logging, indicating a very good suitability for tunneling....

  11. Mechanical Analysis Of Limestone In Jaya, Lhong, And Lhoknga

    Directory of Open Access Journals (Sweden)

    Raihan .

    2012-09-01

    Full Text Available Research about mechanical analysis of limestone in District Jaya, Lhong, and Lhoknga has been done from Dec. 2011 to Mei 2012. This study aim is to classify the limestones based on physical and mechanical tests as well as identify opportunities limestone utilization in accordance with the SII 0378-80 as a condition of quality natural stone for building. Research have been done by testing compressive strength, modulus Young, wear, specific gravity, porosity, and absorption. The result shows that the limestones are qualified natural stone for building the foundation, curbstone, stone and ornamental stone or paste.

  12. The Influence of Combustion-derived pollutants on limestone deterioration

    DEFF Research Database (Denmark)

    Johnson, J.B.; Montgomery, Melanie; Thompson, G.E.

    1996-01-01

    The wet deposition of combustion-derived atmospheric pollutant species, on to freshly cut or diesel-smoked Portland and Monks Park limestone and marble samples, was carried out in a laboratory 'wetting and drying' salt spray chamber for 84 days. Along with the effect of CO2-equilibrated de...... limestones, respectively. Thus the water and hydrogen ion loading effects are significant, as well as the limestone type, but the nature of the anion is not, under the given wetting and drying regime. Further work showed that the increased resistance of marble over that of limestone, to calcium loss...

  13. Disk Refining and Ultrasonication Treated Sugarcane Bagasse Residues for Poly(Vinyl Alcohol) Bio-composites

    Science.gov (United States)

    Qingzheng Cheng; Zhaohui Tong; Luisa Dempere; Lonnie Ingram; Letian Wang; J.Y. Zhu

    2013-01-01

    Disk refining and ultrasonication treated sugarcane bagasse residues reclaimed from the waste stream of a simplified bioethanol process after fermentation were used to fabricate biobased composites with poly(vinyl alcohol) (PVA) by film casting. The morphologies and the size distributions of residue particles were characterized by scanning electronic microscopy and...

  14. Modeling contaminant plumes in fractured limestone aquifers

    DEFF Research Database (Denmark)

    Mosthaf, Klaus; Brauns, Bentje; Fjordbøge, Annika Sidelmann

    Determining the fate and transport of contaminant plumes from contaminated sites in limestone aquifers is important because they are a major drinking water resource. This is challenging because they are often heavily fractured and contain chert layers and nodules, resulting in a complex transport...... model. The paper concludes with recommendations on how to identify and employ suitable models to advance the conceptual understanding and as decision support tools for risk assessment and the planning of remedial actions....... behavior. Improved conceptual models are needed for this type of site. Here conceptual models are developed by combining numerical models with field data. Several types of fracture flow and transport models are available for the modeling of contaminant transport in fractured media. These include...... the established approaches of the equivalent porous medium, discrete fracture and dual continuum models. However, these modeling concepts are not well tested for contaminant plume migration in limestone geologies. Our goal was to develop and evaluate approaches for modeling the transport of dissolved contaminant...

  15. Reclaiming freshwater sustainability in the Cadillac Desert

    Science.gov (United States)

    Sabo, John L.; Sinha, Tushar; Bowling, Laura C.; Schoups, Gerrit H.W.; Wallender, Wesley W.; Campana, Michael E.; Cherkauer, Keith A.; Fuller, Pam L.; Graf, William L.; Hopmans, Jan W.; Kominoski, John S.; Taylor, Carissa; Trimble, Stanley W.; Webb, Robert H.; Wohl, Ellen E.

    2010-01-01

    Increasing human appropriation of freshwater resources presents a tangible limit to the sustainability of cities, agriculture, and ecosystems in the western United States. Marc Reisner tackles this theme in his 1986 classic Cadillac Desert: The American West and Its Disappearing Water. Reisner's analysis paints a portrait of region-wide hydrologic dysfunction in the western United States, suggesting that the storage capacity of reservoirs will be impaired by sediment infilling, croplands will be rendered infertile by salt, and water scarcity will pit growing desert cities against agribusiness in the face of dwindling water resources. Here we evaluate these claims using the best available data and scientific tools. Our analysis provides strong scientific support for many of Reisner's claims, except the notion that reservoir storage is imminently threatened by sediment. More broadly, we estimate that the equivalent of nearly 76% of streamflow in the Cadillac Desert region is currently appropriated by humans, and this figure could rise to nearly 86% under a doubling of the region's population. Thus, Reisner's incisive journalism led him to the same conclusions as those rendered by copious data, modern scientific tools, and the application of a more genuine scientific method. We close with a prospectus for reclaiming freshwater sustainability in the Cadillac Desert, including a suite of recommendations for reducing region-wide human appropriation of streamflow to a target level of 60%.

  16. Enzyme activities in reclaimed coal mine spoils and soils

    Energy Technology Data Exchange (ETDEWEB)

    Fresquez, P R; Aldon, E F; Lindemann, W C

    1987-11-01

    The segregation and stockpiling of topsoil material may reduce enzymatic activities that may hinder normal nutrient cycling processes in reclaimed minelands. The effects of topsoiling and reclamation age on dehydrogenase, nitrogenase, phosphatase, arylsulphatase, amylase, cellulase, invertase and urease activities were evaluated on three reclaimed non-top-soiled and five reclaimed topsoiled areas and compared with an indisturbed reference soil. Three months after topsoiling and revegetation, activities of the enzymes in the reclaimed areas, with the exception of dehydrogenase, were statistically equal to activities of the undisturbed soil. Most enzymes, including dehydrogenase, peaked in the next 1 or 2 years after reclamation with topsoiling and declined thereafter. A 4-year-old topsoiled site (revegetated in 1978) was statistically similar to the undisturbed soil. Amylase activity, however, was significantly lower after the fourth year compared to the undisturbed soil. The non-topsoiled areas, even after 6, 7 and 8 years, appeared to have lower enzyme activities than the younger topsoiled areas or the undisturbed soil. This trend was supported by the finding that the 4-year-old topsoiled site was more enzymatically similar to the undisturbed soil than was the 8-year-old non-topsoiled site (revegetated in 1974). The low enzyme acitivities found in the non-topsoiled areas may be a result of their adverse chemical and physical properties, as well as the low diversity of microorganisms. These studies demonstrate the value of topsoil use for early establishment of soil processes in reclaimed areas. 3 figs., 19 refs., 8 tabs.

  17. Perceptions of Different Stakeholders on Reclaimed Water Reuse: The Case of Beijing, China

    OpenAIRE

    Weiping Chen; Yanying Bai; Weiling Zhang; Sidan Lyu; Wentao Jiao

    2015-01-01

    Public involvement is critical to the successful implementation of reclaimed water reuse programs. Based on the participatory research method, we studied the attitudes of the stakeholders who are involved in reclaimed water reuse in Beijing, China. Results showed that the general public’s knowledge on water resources was poor, while their awareness on reclaimed water reuse was high. The general public showed a strong acceptance of non-contact and non-potable reclaimed water reuse, but their a...

  18. STEAM INJECTION INTO FRACTURED LIMESTONE AT LORING AIR FORCE BASE

    Science.gov (United States)

    A research project on steam injection for the remediation of spent chlorinated solvents from fractured limestone was recently undertaken at the former Loring AFB in Limestone, ME. Participants in the project include the Maine Department of Environmental Protection, EPA Region I,...

  19. Catalytic and Gas-Solid Reactions Involving HCN over Limestone

    DEFF Research Database (Denmark)

    Jensen, Anker; Johnsson, Jan Erik; Dam-Johansen, Kim

    1997-01-01

    In coal-fired combustion systems solid calcium species may be present as ash components or limestone added to the combustion chamber. In this study heterogeneous reactions involving HCN over seven different limestones were investigated in a laboratory fixed-bed quartz reactor at 873-1,173 K...

  20. Effect of limestone particle size on egg production and eggshell ...

    African Journals Online (AJOL)

    Different limestone particle sizes had no effect on any of the tested egg production and eggshell quality parameters. These results suggested that larger particles limestone are not necessarily essential to provide sufficient Ca2+ to laying hens for egg production and eggshell quality at end-of-lay, provided that the dietary Ca ...

  1. Reclaim/recycle of Pt/C catalysts for PEMFC

    International Nuclear Information System (INIS)

    Zhao, Jishi; He, Xiangming; Tian, Jianhua; Wan, Chunrong; Jiang, Changyin

    2007-01-01

    Platinum was reclaimed from Pt/C catalysts of the PEMFC by drying the degraded Pt/C catalysts at 80 o C for 3 h, followed by sintering at 600 o C for 6 h, dissolution by aqua fortis, purification with hydrochloric acid, reduction and filtration, successively. Pt/C catalysts were prepared again from the reclaimed Pt by two proposed processes, e.g., pH value control process and mass control process. The fuel cell with recycled catalysts presented a power density of over 0.18 W cm -2 . The reclaiming of Pt/C catalysts is a potential way for recycling Pt for PEMFC, reducing the cost of PEMFC

  2. Remining to reclaim abandoned mined lands: Virginia's initiative

    International Nuclear Information System (INIS)

    Zipper, C.E.; Lambert, B.

    1998-01-01

    Abandoned Mined Lands (AML) are lands that were mined prior to implementation of the federal Surface Mining Control and Reclamation Act (SMCRA) in 1977, but were inadequately reclaimed. Re-mining of AML is being conducted on a routine basis by coal-mining operations in eastern states such as Virginia. Re-mining is a potentially important means of reclaiming AML. However, under current policies, re-mining operations often fail to permit and reclaim priority 1, 2, and 3 AML, especially those areas which present the most severe environmental problems. This paper describes policy issues which affect the potential for AML reclamation by re-mining operations in mountainous mining areas, such as Virginia; efforts underway in Virginia which seek to resolve those issues; and progress achieved to date under that initiative

  3. The program of reclaim negotiable emission licensing: situation and lessons

    International Nuclear Information System (INIS)

    Soleille, S.

    2004-01-01

    RECLAIM is an innovative and ambitious program of emission trading that concerns the nitrogen oxides emitted by stationary sources in the Basin of Los Angeles ( United States). It began in 1994 and suffered from various weaknesses. Faced with the Californian energy crisis during the summer of 2000, it could not overcome it. Some power plants have been ejected from the market and are now regulated by a traditional command-and-control approach. The analysis of the RECLAIM program and a comparison with similar markets enable us to point out the weaknesses that led to RECLAIM partial failure and to give some insight into the future evolution of the other emission trading markets. (author)

  4. Illinois reclaimed soil productivity: Restoration techniques

    International Nuclear Information System (INIS)

    Smout, G.

    1998-01-01

    Consolidation Coal Co. (Consol) has nearly 8,000 acres of high capability and prime farmland reclamation responsibility in Illinois. It has been involved in research in the area of restored soil productivity since 1976 with the University of Illinois and Southern Illinois University, Carbondale. Consol maintains an intensive program to demonstrate and test deep tillage equipment. The research and in-house demonstrations identified soil physical strength (compaction) as the main limiting factor to restoring a soil's productive capacity. There are two primary ways to address this issue, prevention and amelioration. The former was not an option for Consol because many acres were already reclaimed and the company had a major scraper fleet. Along with other operators in Illinois, Consol started an aggressive search for equipment and techniques that could loosen compacted soils. In 1987 Consol was the first to use the D.M.I.-Super Tiger deep soil plow, originally developed and manufactured by D.M.I., Inc. of Goodfield, Illinois. This plow is composed of a single parabolic, static shank with a 44-inch wide sweep weighing 1,200 pounds. It is capable of plowing 48 inches deep while leaving the top soil in place. A Caterpillar D9L tractor with 460 horsepower is used to pull the plow. In 1990 the decision was made to commit to this equipment as the best technology currently available. In 1994 Consol received a patent waiver from D.M.I. to build its own plow. The Consol built plow has been in use since the summer of 1995. To date, Consol has plowed over 3,900 acres with a D.M.I. plow

  5. Hydraulic retention time on vinasse stabilisation with limestone in the acidogenic phase of anaerobic digestion

    Directory of Open Access Journals (Sweden)

    Ismael Plácido Tomielis

    Full Text Available ABSTRACT: The main problem in anaerobic digestion of low-protein residues is the instability caused acidity. The use of limestone at the same time as a neutralizing agent and support material is innovative because stones wear allows the slow release of the calcium carbonate thereby eliminating dispersers. Free calcium content in the system was measured in two plug flow reactors filled with vinasse at initial pH of 4.50. The proportion of 1.8 tonnes of limestone per m³ of vinasse was evaluated at the Hydraulic Retention Times (HRT of 24, 48, 72, 96 and 120 hours, allowing stabilisation at 96 hours. The ratio of Volatile Acids/Total Alkalinity (VA/TA ranged from 0.2 to 0.4 and the pH reached 7.0, at the HRT of 120 hours. Increasing the HRT also increased the volatile total solids (VTS and fixed total solids (TFS in a similar profile to the measured free calcium content, but calcium remained at the appropriate level of 100 to 250mg l-1. The proportion of limestone/vinasse was adequate to ensure stabilisation, but it is not recommended to reduce the HRT below 96 hours due to the risk of compromising the stability of the anaerobic system.

  6. Field trial of a pulsed limestone diversion well

    Science.gov (United States)

    Sibrell, Philip L.; Denholm, C.; Dunn, Margaret

    2013-01-01

    The use of limestone diversion wells to treat acid mine drainage (AMD) is well-known, but in many cases, acid neutralization is not as complete as would be desired. Reasons for this include channeling of the water through the limestone bed, and the slow reaction rate of the limestone gravel. A new approach to improve the performance of the diversion well was tested in the field at the Jennings Environmental Education Center, near Slippery Rock, PA. In this approach, a finer size distribution of limestone was used so as to allow fluidization of the limestone bed, thus eliminating channeling and increasing particle surface area for faster reaction rates. Also, water flow was regulated through the use of a dosing siphon, so that consistent fluidization of the limestone sand could be achieved. Testing began late in the summer of 2010, and continued through November of 2011. Initial system performance during the 2010 field season was good, with the production of net alkaline water, but hydraulic problems involving air release and limestone sand retention were observed. In the summer of 2011, a finer size of limestone sand was procured for use in the system. This material fluidized more readily, but acid neutralization tapered off after several days. Subsequent observations indicated that the hydraulics of the system was compromised by the formation of iron oxides in the pipe leading to the limestone bed, which affected water distribution and flow through the bed. Although results from the field trial were mixed, it is believed that without the formation of iron oxides and plugging of the pipe, better acid neutralization and treatment would have occurred. Further tests are being considered using a different hydraulic configuration for the limestone sand fluidized bed.

  7. Test results on reuse of reclaimed shower water - A summary

    Science.gov (United States)

    Verostko, Charles E.; Garcia, Rafael; Sauer, Richard; Reysa, Richard P.; Linton, Arthur T.

    1989-01-01

    Results are presented from tests to evaluate a microgravity whole body shower and waste water recovery system design for possible use on the Space Station. Several water recovery methods were tested, including phase change distillation, a thermoelectric hollow fiber membrane evaporation subsystem, and a reverse osmosis dynamic membrane system. Consideration is given to the test hardware, the types of soaps evaluated, the human response to showering with reclaimed water, chemical treatment for microbial control, the procedures for providing hygienic water, and the quality of water produced by the systems. All three of the waste water recovery systems tested successfully produced reclaimed water for reuse.

  8. Development of an iodine generator for reclaimed water purification in manned spacecraft applications

    Science.gov (United States)

    Wynveen, R. A.; Powell, J. D.; Schubert, F. H.

    1973-01-01

    A successful 30-day test is described of a prototype Iodine Generating and Dispensing System (IGDS). The IGDS was sized to iodinate the drinking water nominally consumed by six men, 4.5 to 13.6 kg (10 to 30 lb) water per man-day with a + or - 10 to 20% variation with iodine (I2) levels of 0.5 to 20 parts per million (ppm). The I2 treats reclaimed water to prevent or eliminate microorganism contamination. Treatment is maintained with a residual of I2 within the manned spacecraft water supply. A simplified version of the chlorogen water disinfection concept, developed by life systems for on-site generation of chlorine (Cl2), was used as a basis for IGDS development. Potable water contaminated with abundant E. Coliform Group organisms was treated by electrolytically generated I2 at levels of 5 to 10 ppm. In all instances, the E. coli were eliminated.

  9. Properties, sustainability and elevated temperature behavior of concrete containing Portland limestone cement

    Science.gov (United States)

    El-Hawary, Moetaz; Ahmed, Mahmoud

    2017-09-01

    The utilization of some type of cheap filler as partial cement replacement is an effective way of improving concrete sustainability. With the recent trends to reduce water to cement ratio and improve compaction, there is no enough space or water for complete hydration of cement. This means that actually, a portion of mixed cement acts as expensive filler. Replacing this portion with cheaper filler that requires less energy to produce is, therefore, beneficial. Crushed limestone is the most promising filler. This work is to investigate the effect of the amount of limestone fillers on the sustainability and the fresh and mechanical properties of the resulting concrete. A rich mix is designed with a low water/cement ratio of 0.4. Lime is introduced as a replacement percentage of cement. Ratios of 0, 10, 20 and 30% were used. Slump, compressive strength, specific gravity and water absorption are evaluated for every mix. In addition, the effect of the amount of lime on the residual strength of concrete subjected to elevated temperatures is also investigated. Samples are subjected to six different temperature stations of 20, 100, 200, 300, 500 and 700°C for six hours before being cooled and subsequently tested for compressive strength and specific gravity. Sustainability of the tested mixes is evaluated through reductions in the emitted carbon dioxide, energy and reduction in cost. Based on the annual use of concrete in Kuwait, the sustainability benefits resulting from the use of limestone filler in Kuwait are evaluated and assessed. The paper is concluded with the recommendation of the use of 15% limestone filler as partial cement replacement where the properties and the behavior under high temperature of the resulting concrete are almost the same as those of conventional concrete with considerable cost and sustainability benefits.

  10. 30 CFR 879.15 - Disposition of reclaimed land.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Disposition of reclaimed land. 879.15 Section 879.15 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR ABANDONED MINE LAND RECLAMATION ACQUISITION, MANAGEMENT, AND DISPOSITION OF LANDS AND WATER § 879...

  11. Reclaiming urban youth identity through language in Kenya: the ...

    African Journals Online (AJOL)

    Reclaiming urban youth identity through language in Kenya: the case of Koch FM radio. ... Log in or Register to get access to full text downloads. ... a new constitution that has expanded the democratic space and created broader awareness of ...

  12. The biological costs of not reclaiming bentonite mine spoils

    Science.gov (United States)

    Carolyn Hull Sieg; Daniel W. Uresk; Richard M. Hansen

    1982-01-01

    Bentonite clay has been mined in the northern Great Plains for more than 80 years. Until the late 1960's, mine spoil materials were left in steep piles and no effort was made to restore biological productivity to these disturbed sites. As a result, unreclaimed spoils are barren and eroded. The biological costs of not reclaiming these spoils are examined in this...

  13. 21 CFR 176.260 - Pulp from reclaimed fiber.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Pulp from reclaimed fiber. 176.260 Section 176.260 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD ADDITIVES: PAPER AND PAPERBOARD COMPONENTS Substances...

  14. reClaiming Space & Dialogue in Adult Education

    Science.gov (United States)

    Kawalilak, Colleen A.

    2006-01-01

    This paper critiques current trends in adult education against a backdrop of practice that was once testimony to an educational model that extended beyond formal learning and a business and industry agenda. Adult educators are called upon to reclaim an identity as leaders, in support of a shift in perspective and practice, more aligned to…

  15. Leidos Reclaims Defelice Cup at Annual Golf Tournament | Poster

    Science.gov (United States)

    By Ashley DeVine, Staff Writer Leidos Biomedical Research reclaimed the Defelice Cup trophy from NCI at the eighth annual Ronald H. Defelice golf tournament, held October 14. The final score was 15–7, with Leidos Biomed tying the series 4 to 4. Fourteen players on each team battled it out at Rattlewood golf course in Mount Airy, Md.

  16. Electrical conductivity of sandstone, limestone, and granite

    Energy Technology Data Exchange (ETDEWEB)

    Duba, A.; Piwinskii, A.J.; Santor, M.; Weed, H.C.

    1978-01-01

    The electrical conductivity of cylindrical cores of Westerly granite, Indiana limestone and Nugget, St Peter and Kayenta sandstones was measured at about 25/sup 0/C in vacuo, in air, and after saturation in distilled water, tap water, and 0.1 M NaCl solution. The three-electrode technique with a guard ring and the two-electrode technique without a guard ring were used. Core aspect ratio over the range of 2.00 to 0.25, as well as frequency over the range of 50 Hz to 10 kHz, influences the conductivity of all rocks, especially those measured in vacuo. Measurements from water-saturated samples using a guard ring are not appreciably different from those obtained without a guard ring. The conductivity of rocks saturated in 0.1 M NaCl solution changes least with a change in aspect ratio; for these rocks a linear relationship, known as Archie's Law, exists between log porosity and log conductivity. No simple correlation was found between those factors in rocks saturated with tap or distilled water. Thus, it appears Archie's Law is of questionable value for correlating laboratory data from rocks saturated with low-conductivity fluids.

  17. Incorporation of limestone residue from marble processing plant in the city of Cachoeiro do Itapemirim, Espirito Santo, Brazil, in the production of mortars; Incorporacao de residuo proveniente de usina de beneficiamento de marmore do municipio de Cachoeiro do Itapemirim, ES, Brasil, na confeccao de argamassas

    Energy Technology Data Exchange (ETDEWEB)

    Goncalves, G.P.; Alexandre, J.; Dias, D.P.; Dias Junior, N.S.; Anderson, R.B., E-mail: gabrielkgbs@gmail.co [Universidade Estadual do Norte Fluminense (LECIV/UENF), Campos dos Goytacazes, RJ (Brazil). Centro de Ciencia e Tecnologia. Lab. de Engenharia Civil

    2010-07-01

    Cachoeiro do Itapemirim city (ES), located 136 km from Vitoria, the state's capital, is the largest ornamental stones producer in Brazil, whose beneficiation produces a large amount of waste that, even today, is responsible for major damages done to the environment. This article aims the experimental study of hydrated lime use (product marketed to be used in mortar) by a residue from marble beneficiation from an industry located in that city. Two mixes were made with cement:sand:hydrated lime and cement:sand:residue. The mortars were evaluated by their properties comparisons in fresh and hardened states, namely: consistency index, mass density and incorporated air content, compressive strength, tensile and bending grip for traction. Chemical and mineralogical analysis by X-ray diffraction were also made. The obtained results met the requirements prescribed by ABNT NBR 13 281 (2005). (author)

  18. Incorporation of limestone residue from marble processing plant in the city of Cachoeiro do Itapemirim, Espirito Santo, Brazil, in the production of mortars; Incorporacao de residuo proveniente de usina de beneficiamento de marmore do municipio de Cachoeiro do Itapemirim, ES, Brasil, na confeccao de argamassas

    Energy Technology Data Exchange (ETDEWEB)

    Goncalves, G P; Alexandre, J; Dias, D P; Dias, Junior, N S; Anderson, R.B., E-mail: gabrielkgbs@gmail.co [Universidade Estadual do Norte Fluminense (LECIV/UENF), Campos dos Goytacazes, RJ (Brazil). Centro de Ciencia e Tecnologia. Lab. de Engenharia Civil

    2010-07-01

    Cachoeiro do Itapemirim city (ES), located 136 km from Vitoria, the state's capital, is the largest ornamental stones producer in Brazil, whose beneficiation produces a large amount of waste that, even today, is responsible for major damages done to the environment. This article aims the experimental study of hydrated lime use (product marketed to be used in mortar) by a residue from marble beneficiation from an industry located in that city. Two mixes were made with cement:sand:hydrated lime and cement:sand:residue. The mortars were evaluated by their properties comparisons in fresh and hardened states, namely: consistency index, mass density and incorporated air content, compressive strength, tensile and bending grip for traction. Chemical and mineralogical analysis by X-ray diffraction were also made. The obtained results met the requirements prescribed by ABNT NBR 13 281 (2005). (author)

  19. LUTETIAN LIMESTONES IN THE PARIS REGION: PETROGRAPHIC AND COMPOSITIONAL EXAMINATION

    International Nuclear Information System (INIS)

    BLANC, A.; HOLMES, L.L.; HARBOTTLE, G.

    1998-01-01

    Stone for building and decorating monuments in the Paris Basin from antiquity to the present came from numerous quarries in the Lutetian limestone formations of the region. To identify specific-stone sources used for masonry and sculptures in these monuments, a team of geologists and archaeologists has investigated 300 quarries and collected 2,300 limestone samples for study in a collaborative effort by geologists and chemists. Petrographic and paleontologic examinations of thin sections enable geologists to distinguish the Tertiary Lutetian limestones from similar stone in Jurassic and Cretaceous strata. The methods of the geologist have been supplemented by those of the chemist whose compositional studies by neutron activation analysis can differentiate among the fine-grained upper Lutetian limestones extracted from specific ancient quarries

  20. Improving DMS 9210 requirements for limestone rock asphalt - final report.

    Science.gov (United States)

    2015-03-01

    Limestone Rock Asphalt (LRA) mixtures have been produced and placed for several decades using : specification requirements currently listed under DMS 9210. Several districts have had placement issues : and premature failures at the beginning of 2010....

  1. Limestone doses affecting mineral contents in tropical grass forage

    International Nuclear Information System (INIS)

    Armelin, M.J.A.; Saiki, M.

    2005-01-01

    Field trial was performed at the experimental farm of Southeast Embrapa Cattle, Sao Carlos - SP, Brazil, on a 16 year old Brachiaria decumbens pasture, grown on a distrophic Hapludox (Oxisol), recovered by the use of limestone and fertilizer. The experiments were carried out in random blocks, with 6 replications and 5 treatments. The 100 m 2 blocks were established in the pasture. Each block received a sequence of limestone doses of 0, 1, 2, 4 and 8 t/ha. The forage samples were taken one year after limestone application on soil surface. Instrumental neutron activation analysis (INAA) followed by gamma-ray spectrometry was the analytical method used to determine mineral contents. The statistical analysis showed a negative linear correlation of Br, Co, Cr, Mn and Zn contents in forage with the limestone doses, while the uptake of Mg was affected in a positive way. (author)

  2. A Metagenomic Survey of Limestone Hill in Taiwan

    Science.gov (United States)

    Hsu, Y. W.; Li, K. Y.; Chen, Y. W.; Huang, T. Y.; Chen, W. J.; Shih, Y. J.; Chen, J. S.; Fan, C. W.; Hsu, B. M.

    2016-12-01

    The limestone of Narro-Sky in Tainliao, Taiwan is of Pleistocene reef limestones interbedded in clastic layers that covered the Takangshan anticlines. Understanding how microbial relative abundance was changed in response to changes of environmental factors may contribute to better comprehension of roles that microorganisms play in altering the landscape structures. In this study, microorganisms growing on the wall of limestone, in the water dripping from the limestone wall and of soil underneath the wall were collected from different locations where the environmental factors such as daytime illumination, humidity, or pH are different. Next generation sequencing (NGS) was carried out to examine the compositions and richness of microbial community. The metagenomics were clustered into operational taxonomic units (OTUs) to analyze relative abundance, diversities and principal coordinates analysis (PCoA). Our results showed the soil sample has the highest alpha diversity while water sample has the lowest. Four major phyla, which are Proteobacteria, Acidobacteria, Actinobacteria, and Cyanobacteria, account for 80 % of total microbial biomass in all groups. Cyanobacteria were found most abundantly in limestone wall instead of water or soil of weathering limestone. The PCoA dimensional patterns of each phylum showed a trace of microbial community dynamic changes, which might be affected by environmental factors. This study provides the insights to understand how environmental factors worked together with microbial community to shape landscape structures.

  3. Converting SDAP into gypsum in a wet limestone scrubber

    Energy Technology Data Exchange (ETDEWEB)

    Fogh, F [Faelleskemikerne, Elsamprojekt A/S, Fredericia (Denmark)

    1996-12-01

    The ELSAM power pool has an installed electrical capacity of approx. 5 GW{sub e}, mainly firing import coal. The major base load units are equipped with desulphurization units and three different desulphurization technologies are used: the wet limestone gypsum process, the spray dry absorption process and a sulphuric acid process. Gypsum and sulphuric acid are commercialized, whereas it has been difficult to utilize the spray dry absorption product (SDAP). The main constituents of SDAP are calcium sulphide, calcium chloride, hydrated lime and impurities mainly originating from fly ash. Sulphide can be oxidized into sulphate in acidic solution - the reaction is utilized in the wet limestone gypsum process - and the possibility of using any spare capacity in the wet limestone gypsum units to oxidize the sulphide content of SDAP into sulphate and produce usable gypsum has been investigated in the laboratory and in a 400 MW{sub e} equivalent wet limestone unit. The limestone inhibition effect of the addition of SDAP is currently being studied in the laboratory in order to determine the effect of different SDAP types (plant/coal sources) on limestone reactivity before further long-term full-scale tests are performed and permanent use of the process planned. (EG)

  4. Influence of limestone on the hydration of Portland cements

    International Nuclear Information System (INIS)

    Lothenbach, Barbara; Le Saout, Gwenn; Gallucci, Emmanuel; Scrivener, Karen

    2008-01-01

    The influence of the presence of limestone on the hydration of Portland cement was investigated. Blending of Portland cement with limestone was found to influence the hydrate assemblage of the hydrated cement. Thermodynamic calculations as well as experimental observations indicated that in the presence of limestone, monocarbonate instead of monosulfate was stable. Thermodynamic modelling showed that the stabilisation of monocarbonate in the presence of limestone indirectly stabilised ettringite leading to a corresponding increase of the total volume of the hydrate phase and a decrease of porosity. The measured difference in porosity between the 'limestone-free' cement, which contained less than 0.3% CO 2 , and a cement containing 4% limestone, however, was much smaller than calculated. Coupling of thermodynamic modelling with a set of kinetic equations which described the dissolution of the clinker, predicted quantitatively the amount of hydrates. The quantities of ettringite, portlandite and amorphous phase as determined by TGA and XRD agreed well with the calculated amounts of these phases after different periods of time. The findings in this paper show that changes in the bulk composition of hydrating cements can be followed by coupled thermodynamic models. Comparison between experimental and modelled data helps to understand in more detail the dominating processes during cement hydration

  5. Modeling the influence of limestone addition on cement hydration

    Directory of Open Access Journals (Sweden)

    Ashraf Ragab Mohamed

    2015-03-01

    Full Text Available This paper addresses the influence of using Portland limestone cement “PLC” on cement hydration by characterization of its microstructure development. The European Standard EN 197-1:2011 and Egyptian specification ESS 4756-1/2009 permit the cement to contain up to 20% ground limestone. The computational tools assist in better understanding the influence of limestone additions on cement hydration and microstructure development to facilitate the acceptance of these more economical and ecological materials. μic model has been developed to enable the modeling of microstructural evolution of cementitious materials. In this research μic model is used to simulate both the influence of limestone as fine filler, providing additional surfaces for the nucleation and growth of hydration products. Limestone powder also reacts relatively slow with hydrating cement to form monocarboaluminate (AFmc phase, similar to the mono-sulfoaluminate (AFm phase formed in ordinary Portland cement. The model results reveal that limestone cement has accelerated cement hydration rate, previous experimental results and computer model “cemhyd3d” are used to validate this model.

  6. Thermal properties of the Cobourg Limestone

    Science.gov (United States)

    Pitts, Michelle

    The underground storage of used nuclear fuel in Deep Geologic Repositories (DGRs) has been a subject of research in Canada for decades. One important technical aspect of repository design is the accommodation of the mechanical impacts of thermal inputs (heating) from the fuel as it goes through the remainder of its life cycle. Placement room spacing, a major factor in project cost, will be determined by the ability of the host rock to dissipate heat. The thermal conductivity and linear thermal expansion will determine the evolution of the temperature and thermally-induced stress fields. Thermal processes must be well understood to design a successful DGR. This thesis examines the thermal properties of rocks, how they are influenced by factors such as temperature, pressure, mineralogy, porosity, and saturation; and common methods for calculating and/or measuring these properties. A brief overview of thermal and thermally-coupled processes in the context of DGRs demonstrates the degree to which they would impact design, construction, and operation of these critical structures. Several case histories of major in situ heating experiments are reviewed to determine how the lessons learned could be applied to a Canadian Underground Demonstration Facility (UDF). A mineralogy investigation using X-Ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) examines samples of the Cobourg Limestone from the Bowmanville and Bruce sites, and demonstrates geographical variability within the Cobourg Formation. The thermal properties of samples from the Bowmanville site are determined. A divided bar apparatus was constructed and used to measure thermal conductivity. The temperature measurement component of the divided bar apparatus was used to measure linear thermal expansion. Finally, the past investigations into the thermal impact of a DGR are reviewed, and the implications of the laboratory testing results on similar analyses are discussed.

  7. Influence of the Reclaim from the Cordis Technology on the Core Sand Strength

    Directory of Open Access Journals (Sweden)

    Dańko J.

    2014-12-01

    Full Text Available The investigation results of the mechanical reclamation of spent moulding sands from the Cordis technology are presented in the paper. The quality assessment of the obtained reclaim and the influence of the reclaim fraction in a matrix on the core sand strength is given. The reclaim quality assessment was performed on the basis of the determination of losses on ignition, Na2O content on reclaim grains and pH values. The reclaim constituted 100%, 75% and 50% of the core sand matrix, for which the bending strength was determined. The matrix reclamation treatment was performed in the experimental rotor reclaimer RD-6. Spent sands were applied in as-delivered condition and after the heating to a temperature of 140 °C. Shaped samples for strength tests were made by shooting and hardening of sands in the warmbox technology.

  8. Attrition of limestone by impact loading in fluidized beds

    Energy Technology Data Exchange (ETDEWEB)

    Fabrizio Scala; Fabio Montagnaro; Piero Salatino [Consiglio Nazionale delle Ricerche, Napoli (Italy). Istituto di Ricerche sulla Combustione

    2007-09-15

    The present study addresses limestone attrition and fragmentation associated with impact loading, a process which may occur extensively in various regions of fluidized bed (FB) combustors/gasifiers, primarily the jetting region of the bottom bed, the exit region of the riser, and the cyclone. An experimental protocol for the characterization of the propensity of limestone to undergo attrition/fragmentation by impact loading is reported. The application of the protocol is demonstrated with reference to an Italian limestone whose primary fragmentation and attrition by surface wear have already been characterized in previous studies. The experimental procedure is based on the characterization of the amount and particle size distribution of the debris generated upon the impact of samples of sorbent particles against a target. Experiments were carried out at a range of particle impact velocities between 10 and 45 m/s, consistent with jet velocities corresponding to typical pressure drops across FB gas distributors. The protocol has been applied to either raw or preprocessed limestone samples. In particular, the effect of calcination, sulfation, and calcination/recarbonation cycles on the impact damage suffered by sorbent particles has been assessed. The measurement of particle voidage and pore size distribution by mercury intrusion was also accomplished to correlate fragmentation with the structural properties of the sorbent samples. Fragmentation by impact loading of the limestone is significant. Lime displays the largest propensity to undergo impact damage, followed by the sorbent sulfated to exhaustion, the recarbonated sorbent, and the raw limestone. Fragmentation of the raw limestone and of the sulfated lime follows a pattern typical of the failure of brittle materials. The fragmentation behavior of lime and recarbonated lime better conforms to a disintegration failure mode, with an extensive generation of very fine fragments. 27 refs., 9 figs. 1 tab.

  9. Recycling of Reclaimed Asphalt Pavement in Portland Cement Concrete

    Directory of Open Access Journals (Sweden)

    Salim Al-Oraimi

    2009-06-01

    Full Text Available Reclaimed Asphalt Pavement (RAP is the result of removing old asphalt pavement material. RAP consists of high quality well-graded aggregate coated with asphalt cement. The removal of asphalt concrete is done for reconstruction purposes, resurfacing, or to obtain access to buried utilities. The disposal of RAP represents a large loss of valuable source of high quality aggregate. This research investigates the properties of concrete utilizing recycled reclaimed asphalt pavement (RAP. Two control mixes with normal aggregate were designed with water cement ratios of 0.45 and 0.5. The control mixes resulted in compressive strengths of 50 and 33 MPa after 28 days of curing. The coarse fraction of RAP was used to replace the coarse aggregate with 25, 50, 75, and 100% for both mixtures. In addition to the control mix (0%, the mixes containing RAP were evaluated for slump, compressive strength, flexural strength, and modulus of elasticity. Durability was evaluated using surface absorption test.

  10. Approach to the health-risk management on municipal reclaimed water reused in landscape water system

    Science.gov (United States)

    Liu, X.; Li, J.; Liu, W.

    2008-12-01

    Water pollution and water heavily shortage are both main environmental conflicts in China. Reclaimed water reuse is an important approach to lessen water pollution and solve the water shortage crisis in the city. The heath risk of reclaimed water has become the focus of the public. It is impending to evaluate the health risk of reclaimed water with risk assessment technique. Considering the ways of the reclaimed water reused, it is studied that health risk produced by toxic pollutants and pathogenic microbes in the processes of reclaimed water reused in landscape water system. The pathogenic microbes monitoring techniques in wastewater and reclaimed water are discussed and the hygienic indicators, risk assessment methods, concentration limitations of pathogenic microbes for various reclaimed water uses are studied. The principle of health risk assessment is used to research the exposure level and the health risk of concerned people in a wastewater reuse project where the reclaimed water is applied for green area irrigation in a public park in Beijing. The exposure assessment method and model of various reclaimed water uses are built combining with Beijing reclaimed water project. Firstly the daily ingesting dose and lifetime average daily dose(LADD) of exposure people are provided via field work and monitoring analysis, which could be used in health risk assessment as quantitative reference. The result shows that the main risk comes from the pathology pollutants, the toxic pollutants, the eutrophication pollutants, pathogenic microbes and the secondary pollutants when municipal wastewater is reclaimed for landscape water. The major water quality limited should include pathogenic microbes, toxic pollutants, and heavy metals. Keywords: municipal wastewater, reclaimed water, landscape water, health risk

  11. Infiltration in reclaimed mined land ameliorated with deep tillage treatments

    International Nuclear Information System (INIS)

    Chong, S.K.; Cowsert, P.T.

    1997-01-01

    Reclamation of mined land with heavy machinery can result in soil compaction, which increases soil bulk density and reduces porosity, water infiltrability, root elongation and crop productivity. This paper examines the effect on infiltration in reclaimed surface mined land of a deep tillage treatment, and the subsequent changes in infiltration after the amelioration. The experiment was conducted at the Horse Creek Mine near Conant, Ferry County, IL, USA

  12. Quantifying topographic differences between premining and reclaimed landscapes at a large surface coal mine

    International Nuclear Information System (INIS)

    Friedlander, J.D.

    1994-01-01

    Premining and reclaimed landscapes on 2,300 acres were compared quantitatively at a surface coal mine in western North Dakota. Weighted average slopes were determined by calculating acres in each slope class (0% to 3%, 3% to 6%, 6% to 9%, 9% to 15%, and > 15%) and dividing by the total number of acres. Weighted average slopes were 3.8% and 3.0% for all premining and reclaimed lands respectively. Weighted average slopes were 2.7% and 2.1% for premining and reclaimed croplands respectively. Reclaimed native rangeland slopes are 5.5% compared to 7.0% premining. The acreage of native rangeland with >9% slopes decreased more than 50% during reclamation. For all mined lands there is 25% more reclaimed land with 0% to 3% slopes and 25% less reclaimed land with >6% slopes than before mining. Topographic changes caused by surface mining and reclamation enhance soil conservation, moisture retention, and agricultural productivity. A cross-sectional profile had 26.8 and 15.5 premining and reclaimed land up-down gradient changes per mile respectively, indicating reclaimed land is less diverse than it was prior to mining. Slope class map units average 3.5 and 4.4 acres respectively on premining and reclaimed lands, further indicating reduced diversity. Landscape improvements conflict with regulatory diversity requirements to determine reclamation success

  13. Perceptions of Different Stakeholders on Reclaimed Water Reuse: The Case of Beijing, China

    Directory of Open Access Journals (Sweden)

    Weiping Chen

    2015-07-01

    Full Text Available Public involvement is critical to the successful implementation of reclaimed water reuse programs. Based on the participatory research method, we studied the attitudes of the stakeholders who are involved in reclaimed water reuse in Beijing, China. Results showed that the general public’s knowledge on water resources was poor, while their awareness on reclaimed water reuse was high. The general public showed a strong acceptance of non-contact and non-potable reclaimed water reuse, but their acceptance of the three major water reuse types of river water supplement, park water supplement, and agriculture irrigation was not high. The beneficial use of reclaimed water was admired by water resource managers, industrial sectors, and researchers, and these stakeholders strongly supported the advancement of reclaimed water reuse. However, some of the stakeholders showed concerns about the potential risks from reclaimed wastewater reuse. Among them, risks from waste water treatment facilities were the biggest concern. Stakeholders’ perception of reclaimed water was influenced by their social-economic attributes. This study will enrich the current survey findings on public perception of reclaimed water reuse, particularly in developing countries.

  14. Aquifers in coastal reclaimed lands - real world assessments

    Science.gov (United States)

    Saha, A.; Bironne, A.; Vonhögen-Peeters, L.; Lee, W. K.; Babovic, V. M.; Vermeulen, P.; van Baaren, E.; Karaoulis, M.; Blanchais, F.; Nguyen, M.; Pauw, P.; Doornenbal, P.

    2017-12-01

    Climate change and population growth are significant concerns in coastal regions around the world, where more than 30% of the world's population reside. The numbers continue to rise as coastal areas are increasingly urbanized. Urbanization creates land shortages along the coasts, which has spurred coastal reclamation activities as a viable solution. In this study, we focus on these reclamation areas; reclaimed areas in Singapore, and in the Netherlands, and investigate the potential of these reclaimed bodies as artificial aquifers that could attenuate water shortage problems in addition to their original purpose. We compare how the reclamation methods determine the hydrogeological characteristics of these manmade aquifers. We highlight similarities in freshwater lens development in the artificial shallow aquifers under natural recharge under diverse conditions, i.e. tropical and temperate zones, using numerical models. The characteristics and responses of these aquifers with dynamic freshwater-saltwater interface are contrasted against naturally occurring coastal aquifers where equilibrium was disturbed by anthropogenic activities. Finally, we assess the risks associated with subsidence and saltwater intrusion, combining measurements and numerical models, in case these aquifers are planned for Aquifer Storage and Recovery (ASR) or Managed Aquifer Recharge (MAR) strategies. Relative performances of some ASR schemes are simulated and compared in the reclaimed lands.

  15. Reclaimed mineland curve number response to temporal distribution of rainfall

    Science.gov (United States)

    Warner, R.C.; Agouridis, C.T.; Vingralek, P.T.; Fogle, A.W.

    2010-01-01

    The curve number (CN) method is a common technique to estimate runoff volume, and it is widely used in coal mining operations such as those in the Appalachian region of Kentucky. However, very little CN data are available for watersheds disturbed by surface mining and then reclaimed using traditional techniques. Furthermore, as the CN method does not readily account for variations in infiltration rates due to varying rainfall distributions, the selection of a single CN value to encompass all temporal rainfall distributions could lead engineers to substantially under- or over-size water detention structures used in mining operations or other land uses such as development. Using rainfall and runoff data from a surface coal mine located in the Cumberland Plateau of eastern Kentucky, CNs were computed for conventionally reclaimed lands. The effects of temporal rainfall distributions on CNs was also examined by classifying storms as intense, steady, multi-interval intense, or multi-interval steady. Results indicate that CNs for such reclaimed lands ranged from 62 to 94 with a mean value of 85. Temporal rainfall distributions were also shown to significantly affect CN values with intense storms having significantly higher CNs than multi-interval storms. These results indicate that a period of recovery is present between rainfall bursts of a multi-interval storm that allows depressional storage and infiltration rates to rebound. ?? 2010 American Water Resources Association.

  16. Performance of japanese quails fed feeds containing different corn and limestone particle sizes

    Directory of Open Access Journals (Sweden)

    DA Berto

    2007-09-01

    Full Text Available This study aimed at evaluating performance and egg quality of Japanese quails fed feeds containing different corn and limestone particle sizes. A total number of 648 birds in the peak of production was distributed in a random complete block experimental design, using a 2x3 factorial arrangement (2 corn particle sizes and 3 limestone particle sizes. Birds were designated to one of two blocks, with six replicates of 18 birds each. Mean geometric diameter (MGD values used were 0.617mm and 0.723mm (corn fine and coarse particle sizes, respectively, and 0.361mm, 0.721mm, and 0.947mm (limestone fine, intermediate and coarse particle sizes, respectively. The following treatments were applied: T1: fine corn feed, with 100% fine limestone; T2: fine corn feed, with 50% fine limestone and 50% intermediate limestone; T3: fine corn feed, with 50% fine limestone and 50% coarse limestone; T4: coarse corn feed, with 100% fine limestone; T5: coarse corn feed, with 50% fine limestone and 50% intermediate limestone; T6: coarse corn feed, with 50% fine limestone and 50% coarse limestone. The experiment lasted 112 days, consisting of 4 cycles of 28 days. No significant interaction was observed among corn and limestone particle sizes for any of the analyzed parameters. There were no significant effects (p>0.05 of the tested corn particle sizes on quail performance or egg quality. There were significant (p<0.05 isolated effects of limestone particle size only on the percentage of cracked eggs, which was reduced when birds fed 50% coarse limestone (0.947mm and 50% fine limestone (0.361mm as compared to those fed 100% fine limestone. Therefore, the inclusion of 50% coarse limestone (0.947mm is recommended for quail egg production.

  17. CALCIUM OXIDE CHARACTERISTICS PREPARED FROM AMBUNTEN’S CALCINED LIMESTONE

    Directory of Open Access Journals (Sweden)

    Fatimatul Munawaroh

    2018-05-01

    Full Text Available Calcium oxide (CaO and calcium carbonate (CaCO3 are widely used in industry. CaO and CaCO3 can be synthesized or derived from limestone. The purpose of this study to determine the characteristics of CaO calcined limestone from Ambunten Sumenep. Lime in calcined at 850 ° C for 6 hours. Characterization of X-ray fluorescence (XRF was conducted to determine the chemical composition of limestone, X-ray diffraction test (XRD to find the lime crystalline phase and FTIR test to determine the absorption of wave number. XRF test results showed that the limestone chemical composition consisted of Ca of 95.37% as the dominant element, Mg of 4.1%, Fe 0.17% and Y by 0.39%. The XRD test results showed that the limestone crystal phase is ankerite (Ca [Fe, Mg] [CO3] 2 and after the calcined phase calcination is vaterite (Ca [OH] 2, calcite (CaO and calcite (CaCO3. While the FTIR test results show that the CaO spectra are seen at 3741.24, 1417.12 and 874.14 cm-1.

  18. Modifying the properties of finely ground limestone by tumbling granulation

    Science.gov (United States)

    Macho, Oliver; Eckert, Maroš; Tomášová, Barbora; Peciar, Peter; Ščasný, Martin; Fekete, Roman; Peciar, Marián

    2016-06-01

    Calcium carbonate in the form of finely ground limestone is a material that has found its application in a wide range of industries, in the chemical, rubber, agricultural, and paper industries, is used for desulfurization of boilers and other. In civil engineering, ground limestone is used for the production of building materials, plaster and mortar mixtures, as a filler in concrete mixtures, in road construction, and as an essential component of mastic asphalt. This paper deals with examining the modification of the properties of finely ground limestone by the tumbling agglomeration method. It has been shown that the components of concrete with a round grain have a positive effect on the pumping of concrete in comparison with an elongated grain or the rough surface of crushed stone. The experiments will be carried out on a granulation plate using a variety of granulation liquid. The agglomerates and their properties were compared with untreated finely ground limestone, with a focus on detecting changes in compressibility, density and particle size. The output of this paper is a description and graphical representation of the changes in the properties of ground limestone before and after the agglomeration process.

  19. Characterization of Limestone as Raw Material to Hydrated Lime

    Science.gov (United States)

    Salem Hwidi, Rajeb; Nuraiti Tengku Izhar, Tengku; Saad, Farah Naemah Mohd

    2018-03-01

    In Malaysia, limestone is essentially important for the economic growth as raw materials in the industry sector. Nevertheless, a little attention was paid to the physical, chemical, mineralogical, and morphological properties of the limestone using X-ray fluorescence (X-RF), X-ray diffraction (X-RD), Fourier transform infrared spectroscopy (FTIR), and Scanning electron microscopy / energy dispersive x-ray spectroscopy (SEM-EDS) respectively. Raw materials (limestone rocks) were collected from Bukit Keteri area, Chuping, Kangar, Perlis, Malaysia. Lab crusher and lab sieved were utilized to prepare five different size of ground limestone at (75 µm, 150 µm, 225 µm, 300, and 425 µm) respectively. It is found that the main chemical composition of bulk limestone was Calcium oxide (CaO) at 97.58 wt.% and trace amount of MnO, Al2O3, and Fe2O3 at 0.02%, 0.35%, and 0.396% respectively. XRD diffractograms showed characteristic peaks of calcite and quartz. Furthermore, main FTIR absorption bands at 1,419, 874.08 and 712.20 cm-1 indicated the presence of calcite. The micrographs showed clearly the difference of samples particle size. Furthermore, EDS peaks of Ca, O, and C elements confirmed the presence of CaCO3 in the samples.

  20. Modifying the properties of finely ground limestone by tumbling granulation

    Directory of Open Access Journals (Sweden)

    Macho Oliver

    2016-06-01

    Full Text Available Calcium carbonate in the form of finely ground limestone is a material that has found its application in a wide range of industries, in the chemical, rubber, agricultural, and paper industries, is used for desulfurization of boilers and other. In civil engineering, ground limestone is used for the production of building materials, plaster and mortar mixtures, as a filler in concrete mixtures, in road construction, and as an essential component of mastic asphalt. This paper deals with examining the modification of the properties of finely ground limestone by the tumbling agglomeration method. It has been shown that the components of concrete with a round grain have a positive effect on the pumping of concrete in comparison with an elongated grain or the rough surface of crushed stone. The experiments will be carried out on a granulation plate using a variety of granulation liquid. The agglomerates and their properties were compared with untreated finely ground limestone, with a focus on detecting changes in compressibility, density and particle size. The output of this paper is a description and graphical representation of the changes in the properties of ground limestone before and after the agglomeration process.

  1. Initial kinetics of the direct sulfation of limestone

    DEFF Research Database (Denmark)

    Hu, Guilin; Shang, Lei; Dam-Johansen, Kim

    2008-01-01

    The initial kinetics of direct sulfation of Faxe Bryozo, a porous bryozoan limestone was studied in the temperature interval from 873 to 973 K in a pilot entrained flow reactor with very short reaction times (between 0.1 and 0.6 s). The initial conversion rate of the limestone - for conversions...... less than 0.3% - was observed to be significantly promoted by higher SO2 concentrations and lower CO2 concentrations, whereas 02 showed negligible influence. A mathematical model for the sulfation of limestone involving chemical reaction at calcite grain surfaces and solid-state diffusion of carbonate...... ions in calcite grains is established. The validity of the model is limited to the initial sulfation period, in which nucleation of the solid product calcium sulphate is not started. This theoretical reaction-diffusion model gives a good simulation of the initial kinetics of the direct sulfation...

  2. Limestone attrition under simulated oxyfiring Fluidized-Bed combustion conditions

    Energy Technology Data Exchange (ETDEWEB)

    Scala, F. [Istituto di Ricerche sulla Combustione - CNR, Napoli (Italy); Salatino, P. [Dipartimento di Ingegneria Chimica - Universita degli Studi di Napoli Federico II, Napoli (Italy)

    2009-03-15

    Limestone attrition by surface wear was studied during the flue gas desulfurization under simulated fluidized-bed (FB) oxyfiring conditions and hindered calcination. Bench-scale experimental tests were carried out using well-established techniques previously developed for the characterization of sulfation and attrition of sorbents in air-blown atmospheric FB combustors. The experimental limestone conversion and attrition results were compared with those previously obtained with the same limestone under simulated air-blown combustion conditions. The differences in the conversion and attrition extents and patterns associated with oxyfiring as compared to air-blown atmospheric combustion were highlighted and related to the different particle morphologies and thicknesses of the sulfate layer. It was noted that attrition could play an important role in practical circulating FB combustor operation, by effectively enhancing particle sulfation under both oxyfiring and air-blown combustion conditions. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

  3. Characterization of limestone of region South and Southeast of Para

    International Nuclear Information System (INIS)

    Marinho, A.R.O.; Vieira, J.H.A.; Antunes Junior, L.V.; Medeiros, A.C.; Souza, G.P.

    2014-01-01

    Limestone is used in daily activities, and it is common the use of products containing calcium carbonate in various applications, from construction to food production, air purification to sewage treatment, the sugar refining materials for the toothpaste, the manufacture of glass and steel in the manufacture of paper, plastics, paints, ceramics and many others. The Limestone present in the region of south and southeast of Para is presented in deposits that have not been explored on a large scale, being justified a deepening in characteristics thereof. For the characterization of the material, gross samples were comminuted by crushing and ball mill, sieved and then separated into aliquots. In the end were used fluorescence analysis of X-ray, diffraction X-rays, determination of the moisture and loss on ignition of the material at 950 °C for one hour, obtaining results of a dolomitic limestone. (author)

  4. Effect of SO2 Dry Deposition on Porous Dolomitic Limestones

    Directory of Open Access Journals (Sweden)

    Florica Doroftei

    2010-01-01

    Full Text Available The present study is concerned with the assessment of the relative resistance of a monumental dolomitic limestone (Laspra – Spain used as building material in stone monuments and submitted to artificial ageing by SO2 dry deposition in the presence of humidity. To investigate the protection efficiency of different polymeric coatings, three commercially available siloxane-based oligomers (Lotexan-N, Silres BS 290 and Tegosivin HL 100 and a newly synthesized hybrid nanocomposite with silsesquioxane units (TMSPMA were used. A comparative assessment of the data obtained in this study underlines that a better limestone protection was obtained when treated with the hybrid nanocomposite with silsesquioxane units.

  5. Oxic limestone drains for treatment of dilute, acidic mine drainage

    Science.gov (United States)

    Cravotta, Charles A.

    1998-01-01

    Limestone treatment systems can be effective for remediation of acidic mine drainage (AMD) that contains moderate concentrations of dissolved O2 , Fe3+ , or A13+ (1‐5 mg‐L‐1 ). Samples of water and limestone were collected periodically for 1 year at inflow, outflow, and intermediate points within underground, oxic limestone drains (OLDs) in Pennsylvania to evaluate the transport of dissolved metals and the effect of pH and Fe‐ and Al‐hydrolysis products on the rate of limestone dissolution. The influent was acidic and relatively dilute (pH 1 mg‐L‐1 ) but was near neutral (pH = 6.2‐7.0); Fe and Al decreased to less than 5% of influent concentrations. As pH increased near the inflow, hydrous Fe and Al oxides precipitated in the OLDs. The hydrous oxides, nominally Fe(OH)3 and AI(OH)3, were visible as loosely bound, orange‐yellow coatings on limestone near the inflow. As time elapsed, Fe(OH)3 and AI(OH)3 particles were transported downflow. During the first 6 months of the experiment, Mn 2+ was transported conservatively through the OLDs; however, during the second 6 months, concentrations of Mn in effluent decreased by about 50% relative to influent. The accumulation of hydrous oxides and elevated pH (>5) in the downflow part of the OLDs promoted sorption and coprecipitation of Mn as indicated by its enrichment relative to Fe in hydrous‐oxide particles and coatings on limestone. Despite thick (~1 mm) hydrous‐oxide coatings on limestone near the inflow, CaCO3 dissolution was more rapid near the inflow than at downflow points within the OLD where the limestone was not coated. The rate of limestone dissolution decreased with increased residence time, pH, and concentrations of Ca2+ and HCO3‐ and decreased PCO2. The following overall reaction shows alkalinity as an ultimate product of the iron hydrolysis reaction in an OLD:Fe2+ + 0.25 O2 +CaCO3 + 2.5 H2O --> Fe(OH)3 + 2 Ca2+ + 2 HCO3-where 2 moles of CaCO3 dissolve for each mole of Fe(OH)3 produced

  6. Effects of reclaimed asphalt pavement on indirect tensile strength test of conditioned foamed asphalt mix

    International Nuclear Information System (INIS)

    Katman, Herda Yati; Norhisham, Shuhairy; Ismail, Norlela; Ibrahim, Mohd Rasdan; Matori, Mohd Yazip

    2013-01-01

    This paper presents the results of Indirect Tensile Strength (ITS) Test for samples prepared with reclaimed asphalt pavement (RAP). Samples were conditioned in water at 25°C for 24 hours prior to testing. Results show that recycled aggregate from reclaimed asphalt pavement performs as well as virgin aggregate.

  7. Rethink, Reimagine, Reinvent: The Reggio Emilia Approach to Incorporating Reclaimed Materials in Children's Artworks

    Science.gov (United States)

    Eckhoff, Angela; Spearman, Mindy

    2009-01-01

    Introducing reclaimed materials into the art classroom provides students with unique opportunities to connect ordinary, discarded objects with unique, personal artistic creations. In an effort to better understand this connection, this article explores existing pedagogical precedents that support the role of the inclusion of reclaimed materials in…

  8. NR based curred latex material reclaimed with 2,2'-dibenzamidodiphenyldisulphide in truck tyre tread compound

    NARCIS (Netherlands)

    Rajan, V.V.; Dierkes, Wilma K.; Joseph, R.; Noordermeer, Jacobus W.M.

    2006-01-01

    It is observed that reclamation of natural rubber latex based rubber using 2,2'-dibenzamidodiphenyldisulphide as reclaiming agent is an optional methodology for recycling of waste latex rubber (WLR). For progressive replacement of virgin natural rubber by the reclaim, two alternatives curing system

  9. [Assessment of ecological environment benefits of reclaimed water reuse in Beijing].

    Science.gov (United States)

    Fan, Yu-Peng; Chen, Wei-Ping

    2014-10-01

    With the rapid development of the social economy and the sustained growth of population, China is facing increasingly serious water problems, and reclaimed water utilization has become an effective measure to solve water shortage problem and to control further deterioration of the ecological environment. Reclaimed water utilization can not only save a lot of fresh water, but also reduce the environmental impact of wastewater discharge, and thus has great ecological environmental benefits, including resource, environmental and human health benefits and so on. This study used the opportunity cost method to construct an evaluation system for ecological environmental benefits of reclaimed water utilization, and Beijing was taken as an example to conduct an estimation of ecological environmental benefits of reclaimed water utilization. Research results indicated that the reclaimed water utilization in Beijing had considerable environmental benefits for ¥ 1.2 billion in 2010, in which replacement of fresh water accounted for the largest share. The benefits of environmental improvement and groundwater recharge were large, while the other benefits were small or negative. The ecological environment benefits of reclaimed water utilization in Beijing was about 1.8 times that of its direct economic benefits, showing that reclaimed water utilization was in accordance with sustainable development. Related methods and results will provide scientific basis to promote the development of reclaimed water utilization in our country.

  10. Sodium sesquicarbonate (Akang) and limestone as catalysts for the ...

    African Journals Online (AJOL)

    Production of monoglycerides from palm and palm kernel oils were carried out using sodium sesquicarbonate (akang) and lime stone as catalysts.The results showed that the maximum monoglyceride formed is in the range of 49–57% of the fatty product for the limestone catalyst and 78 – 92% for the sodium ...

  11. The Solnhofen Limestone: A stony heritage of many uses

    Science.gov (United States)

    Kölbl-Ebert, Martina; Kramar, Sabina; Cooper, Barry J.

    2016-04-01

    High above the valley of the River Altmühl (Bavaria, Germany), between Solnhofen to the west and Kelheim to the east, numerous quarries give access to thinly plated limestone from the Upper Jurassic, some 150 million years before the present. The main quarry areas lie around the town of Eichstätt and between the villages of Solnhofen, Langenaltheim and Mörnsheim. Here limestone slabs have been quarried for several hundred years, some even in Roman times. Solnhofen Limestone is famous worldwide; not only because it is a beautiful building stone of high quality, but also because of the exceptionally well-preserved fossils it contains -among them the early bird Archaeopteryx. The quarry industry between Solnhofen and Eichstätt has shaped a cultural landscape, with old and new quarries sunk into the plain and numerous spoil heaps rising above it, for the rock is not all economically useful. But many of the spoil heaps and the old quarries are environmentally protected as they provide a habitat for some rare plants and animals. It is not necessary to cut the Solnhofen Limestone with a saw: it is split by hand into thin and even slabs or sheets which are used for flagstones and wall covers, which since centuries are sold world-wide. Locally it also serves as roof tiles for traditional houses. Thick slabs of especially fine quality may be found near Solnhofen and Mörnsheim and are used for lithography printing.

  12. Effect of Limestone Powder on Microstructure of Ternary Cementitious System

    NARCIS (Netherlands)

    Zhang, Y.; Ye, G.

    2012-01-01

    The pressure to reach sustainability favours the development of ternary composite cement. The synergistic effect on mechanical behaviour at 28 days between limestone powder (LP) and pozzolanic additives, i.e. fly ash (FA) and blast furnace slag (BFS), has been documented. In order to better

  13. Kinetic Study of Calcination of Jakura Limestone Using Power Rate ...

    African Journals Online (AJOL)

    The calcination of Jakura limestone was also found to be first order reaction with respect to CaCO3 concentration having average regression coefficient of 0.99. The temperature dependent terms were found using Arrhenius law and it was observed that the reaction temperature has a direct effect on the rate of reaction.

  14. Limestone rocks analysis by X-ray fluorescence analysis

    International Nuclear Information System (INIS)

    Izquierdo M, G.; Ponce R, R.; Vazquez J, J.

    1996-01-01

    By request of a private company, employing basically X-ray fluorescence analysis (X RF), was established a fast and accurate method for the analysis of the major elements in limestone rocks. Additionally, for complementing analysis was determined by ion chromatography, the chlorides appearance and by atomic absorption of sodium. By gravimetry, was determined the losses by ignition and the alpha quartz. (Author)

  15. Hydrate Phase Assemblages in Calcium Sulfoaluminate - Metakaolin - Limestone Blends

    DEFF Research Database (Denmark)

    Pedersen, Malene Thostrup; Lothenbach, Barbara; Winnefeld, Frank

    2017-01-01

    The combination of a commercial calcium sulfoaluminate (CSA) cement with metakaolin (MK) and limestone (LS) as supplementary cementitious materials (SCMs) is investigated for a CSA replacement level of 20 wt%. In addition to a pure CSA cement, paste samples have been prepared for three blends wit...

  16. Flora of Chihuahuan desertscrub on limestone in northeastern Sonora, Mexico

    Science.gov (United States)

    Thomas R. Van Devender; Ana Lilia Reina-Guerrero; J. Jesus. Sanchez-Escalante

    2013-01-01

    Transects were done in desertscrub on limestone to characterize the flora of the westernmost Chihuahuan Desert. Most of the sites (15) were in the Municipios of Agua Prieta and Naco in northeastern Sonora, with single sites near Ascensión, northwestern Chihuahua and east of Douglas in southeastern Arizona. A total of 236 taxa were recorded on transects. Dicot perennial...

  17. Innovative Field Investigations in Limestone using a FACT-FLUTe

    DEFF Research Database (Denmark)

    Mosthaf, Klaus; Barrett Sørensen, Mie; Broholm, Mette Martina

    2015-01-01

    and the prevailing aqueous pore water concentrations for a range of hydraulic parameters and conditions typical for limestone aquifers. Results and outlook The sorption experiments showed very strong sorption with reasonably linear sorption isotherms over a very large concentration range for individual chlorinated...

  18. Geophysical mapping of contaminant leachate around a reclaimed open dumpsite

    Directory of Open Access Journals (Sweden)

    W.O. Raji

    2017-07-01

    Full Text Available Very low frequency electromagnetic (VLF-EM, 2D Electrical Resistivity Profiling (2D ERP and Vertical Electrical Sounding (VES methods of geophysics were deployed to map the extent of leachate contamination in near-surface rocks around a popular reclaimed dumpsite in north central Nigeria. Two years after abandon and waste excavation; the dumpsite was converted to a residential area with over 80 houses under construction. Prior to waste dumping operation, clay-seal was installed at 2 m depth around the dumpsite to prevent leachate from the waste material flowing to the adjoining area. Results from VLF, 2D ERP, and VES show presence of leachate contamination in rocks and soil of the reclaimed dumpsite. Leachate has spread laterally up to a distance of about 1 km on the northern and southern parts of the dumpsite centre, and up to a depth of about 20 m. Compared to the results of similar survey in an area outside the dumpsite, leachate infiltration raised the conductivity signature of the rocks around the dumpsite by about 200%: from 7% to 22%. Both VLF-EM and 2D ERP show the presence of approximate north – south oriented structures/fracture characterised by high conductivity. VES results show the presence of four – five geo-electric layers. Important conclusions from the study are that (i leachate is still present in the rocks and soil of the reclaimed dumpsite two years after the abandonment and excavation of the waste materials, and (ii the clay seal installed around the dumpsite could not prevent leachate migration to the adjoining areas.

  19. Environmental risk evaluation of the use of mine spoils and treated sewage sludge in the ecological restoration of limestone quarries

    Science.gov (United States)

    Jordán, M. M.; Pina, S.; García-Orenes, F.; Almendro-Candel, M. B.; García-Sánchez, E.

    2008-07-01

    The ecologic restoration criteria in areas degraded from extraction activities require making use of their mine spoils. These materials do not meet fertility conditions to guarantee restoration success and therefore, need the incorporation of organic amendments to obtain efficient substratum. Reducing the deficiencies in the organic material and restoration material nutrients with the contribution of treated sewage sludge is proposed in this work. This experiment was based on a controlled study using columns. The work was conducted with two mine spoils, both very rich in calcium carbonate. The first mineral, of poor quality, came from the formation of aggregates of crushed limestone ( Z). The other residual material examined originated in limestone extraction, formed by the levels of interspersed non-limestone materials and the remains of stripped soils ( D). Two treatments were undertaken (30,000 and 90,000 kg/ha of sewage sludge), in addition to a control treatment. The water contribution was carried out with a device that simulated either short-duration rain or a flooding irrigation system in order to cover the surface and then percolate through the soil. The collection of leached water took place 24 h after the applications. Different parameters of the leached water were determined, including pH, electrical conductivity, nitrate anions, ammonium, phosphates, sulphates and chlorides. The values obtained for each irrigation application are discussed, and the nitrate values obtained were very elevated.

  20. Soil properties evolution after irrigation with reclaimed water

    Science.gov (United States)

    Leal, M.; González-Naranjo, V.; de Miguel, A.; Martínez-Hernández, V.; Lillo, J.

    2012-04-01

    Many arid and semi-arid countries are forced to look for new and alternative water sources. The availability of suitable quality water for agriculture in these regions often is threatened. In this context of water scarcity, the reuse of treated wastewater for crop irrigation could represent a feasible solution. Through rigorous planning and management, irrigation with reclaimed water presents some advantages such as saving freshwater, reducing wastewater discharges into freshwater bodies and decreasing the amount of added fertilizers due to the extra supply of nutrients by reclaimed water. The current study, which involves wastewater reuse in agriculture, has been carried out in the Experimental Plant of Carrión de los Céspedes (Sevile, Spain). Here, two survey parcels equally designed have been cultivated with Jatropha curcas L, a bioenergetic plant and a non-interfering food security crop. The only difference between the two parcels lies on the irrigation water quality: one is irrigated with groundwater and another one with reclaimed water. The main aim of this study focuses on analysing the outstanding differences in soil properties derived from irrigation with two water qualities, due to their implications for plant growth. To control and monitor the soil variables, soil samples were collected before and after irrigation in the two parcels. pH, electrical conductivity, cation exchange capacity, exchangeable cations (Ca2+, Mg2+, Na+ and K+), kjeldahl nitrogen, organic matter content and nutrients (boron, phosphorus, nitrogen, potassium) were measured. Data were statistically analyzed using the R package. To evaluate the variance ANOVA test was used and to obtain the relations between water quality and soil parameters, Pearson correlation coefficient was computed. According to other authors, a decrease in the organic matter content and an increase of parameters such as pH, electrical conductivity and some exchangeable cations were expected. To date and after

  1. 0-6686 : improving DMS 9210 requirements for limestone rock asphalt : [project summary].

    Science.gov (United States)

    2013-08-01

    Limestone rock asphalt (LRA) mixtures have : been produced and placed for several decades : using specification requirements currently listed : under DMS 9210, Limestone Rock Asphalt (LRA). : Several Texas Department of Transportation : (TxDOT) distr...

  2. Assessment of Environmental Impacts of Limestone Quarrying Operations in Thailand

    Directory of Open Access Journals (Sweden)

    Kittipongvises Suthirat

    2017-11-01

    Full Text Available Environmental impacts of the mineral extraction have been a public concern. Presently, there is widespread global interest in the area of mining and its sustainability that focused on the need to shift mining industry to a more sustainable framework. The aim of this study was to systematically assess all possible environmental and climate change related impacts of the limestone quarrying operation in Thailand. By considering the life cycle assessment method, the production processes were divided into three phases: raw material extraction, transportation, and comminution. Both IMPACT 2002+ and the Greenhouse Gas Protocol methods were used. Results of IMPACT 2002+ analysis showed that per 1 ton crushed limestone rock production, the total depletion of resource and GHGs emissions were 79.6 MJ and 2.76 kg CO2 eq., respectively. Regarding to the four damage categories, ‘resources’ and ‘climate change’ categories were the two greatest environmental impacts of the limestone rock production. Diesel fuel and electricity consumption in the mining processes were the main causes of those impacts. For climate change, the unit of CO2 eq. was expressed to quantify the total GHGs emissions. Estimated result was about 3.13 kg CO2 eq. per ton limestone rock product. The results obtained by the Greenhouse Gas Protocol were also similar to IMPACT 2002+ method. Electrical energy consumption was considered as the main driver of GHGs, accounting for approximately 46.8 % of total fossil fuel CO2 emissions. A final point should be noted that data uncertainties in environmental assessment over the complete life cycle of limestone quarrying operation have to be carefully considered.

  3. Assessment of Environmental Impacts of Limestone Quarrying Operations in Thailand

    Science.gov (United States)

    Kittipongvises, Suthirat

    2017-11-01

    Environmental impacts of the mineral extraction have been a public concern. Presently, there is widespread global interest in the area of mining and its sustainability that focused on the need to shift mining industry to a more sustainable framework. The aim of this study was to systematically assess all possible environmental and climate change related impacts of the limestone quarrying operation in Thailand. By considering the life cycle assessment method, the production processes were divided into three phases: raw material extraction, transportation, and comminution. Both IMPACT 2002+ and the Greenhouse Gas Protocol methods were used. Results of IMPACT 2002+ analysis showed that per 1 ton crushed limestone rock production, the total depletion of resource and GHGs emissions were 79.6 MJ and 2.76 kg CO2 eq., respectively. Regarding to the four damage categories, `resources' and `climate change' categories were the two greatest environmental impacts of the limestone rock production. Diesel fuel and electricity consumption in the mining processes were the main causes of those impacts. For climate change, the unit of CO2 eq. was expressed to quantify the total GHGs emissions. Estimated result was about 3.13 kg CO2 eq. per ton limestone rock product. The results obtained by the Greenhouse Gas Protocol were also similar to IMPACT 2002+ method. Electrical energy consumption was considered as the main driver of GHGs, accounting for approximately 46.8 % of total fossil fuel CO2 emissions. A final point should be noted that data uncertainties in environmental assessment over the complete life cycle of limestone quarrying operation have to be carefully considered.

  4. Additional Gigantoproductus species from the upper Visean-Namurian limestone of Kotaki, central Japan

    OpenAIRE

    Ibaraki, Yousuke; Tazawa, Jun-ichi; Nakamura, Yukio

    2010-01-01

    A large productid brachiopod species, Gigantoproductus aurita (Bolkhovitinova, 1938), is described from the Tsuchikurazawa Limestone (upper Visean-Namurian), a large limestone block within a Permian accretionary complex of Kotaki, Itoigawa City, Niigata Prefecture, central Japan. This is the fourth described Gigantoproductus species from the Tsuchikurazawa Limestone. The range of G. aurita may extend to late Visean on the basis of the previous fossil records of the limestone.

  5. Perfect sound insulation property of reclaimed waste tire rubber

    Science.gov (United States)

    Ubaidillah, Harjana, Yahya, Iwan; Kristiani, Restu; Muqowi, Eki; Mazlan, Saiful Amri

    2016-03-01

    This article reports an experimental investigation of sound insulation and absorption performance of a materials made of reclaimed ground tire rubber which is known as un-recyclable thermoset. The bulk waste tire is processed using single step recycling methods namely high-pressure high-temperature sintering (HPHTS). The bulk waste tire is simply placed into a mold and then a pressure load of 3 tons and a heating temperature of 200°C are applied to the mold. The HPHTS conducted for an hour and then it is cooled in room temperature. The resulted product is then evaluated the acoustical properties namely sound transmission loss (STL) and sound absorption coefficient using B&K Tube Kit Type 4206-T based on ISO 10534-2, ASTM E1050 and ASTM E2611. The sound absorption coefficient is found about 0.04 until 0.08 while STL value ranges between 50 to 60 dB. The sound absorption values are found to be very low (<0.1), while the average STL is higher than other elastomeric matrix found in previous work. The reclaimed tire rubber through HPHTS technique gives good soundproof characteristic.

  6. Reclaimed wastewater quality enhancement by oxygen injection during transportation.

    Science.gov (United States)

    Rodríguez-Gómez, L E; Alvarez, M; Rodríguez-Sevilla, J; Marrero, M C; Hernández, A

    2011-01-01

    In-sewer treatments have been studied in sewer systems, but few have been carried out on reclaimed wastewater systems. A study of oxygen injection has been performed in a completely filled gravity pipe, 0.6 m in diameter and 62 km long, in cast iron with concrete inside coating, which is part of the reclaimed wastewater reuse scheme of Tenerife (Spain). A high pressure oxygen injection system was installed at 16.0 km from pipe inlet and a constant dosage of 30 mg/L O(2) has been injected during six months, under three different operational modes (low COD, 63 mg/L; high COD, 91 mg/L; and partially nitrified water). Oxygen has been consumed in nitrification and organic matter reduction. Generally, nitrification is clearly favored instead of the organic matter oxidation. Nitrification occurs, in general, with nitrite accumulation due to the presence of free ammonia above 1 mg/L. Denitrification is in all cases incomplete due to a limitation of easily biodegradable organic matter content, inhibiting the appearance of anaerobic conditions and sulfide generation. A notable reduction of organic matter parameters is achieved (TSS below 10 mg/L), which is significantly higher than that observed under the ordinary transport conditions without oxygen. This leads to a final cost reduction, and the oxygen injection system helps water reuse managers to maintain a final good water quality in the case of a treatment plant malfunction.

  7. Integrated identification and control for nanosatellites reclaiming failed satellite

    Science.gov (United States)

    Han, Nan; Luo, Jianjun; Ma, Weihua; Yuan, Jianping

    2018-05-01

    Using nanosatellites to reclaim a failed satellite needs nanosatellites to attach to its surface to take over its attitude control function. This is challenging, since parameters including the inertia matrix of the combined spacecraft and the relative attitude information of attached nanosatellites with respect to the given body-fixed frame of the failed satellite are all unknown after the attachment. Besides, if the total control capacity needs to be increased during the reclaiming process by new nanosatellites, real-time parameters updating will be necessary. For these reasons, an integrated identification and control method is proposed in this paper, which enables the real-time parameters identification and attitude takeover control to be conducted concurrently. Identification of the inertia matrix of the combined spacecraft and the relative attitude information of attached nanosatellites are both considered. To guarantee sufficient excitation for the identification of the inertia matrix, a modified identification equation is established by filtering out sample points leading to ill-conditioned identification, and the identification performance of the inertia matrix is improved. Based on the real-time estimated inertia matrix, an attitude takeover controller is designed, the stability of the controller is analysed using Lyapunov method. The commanded control torques are allocated to each nanosatellite while the control saturation constraint being satisfied using the Quadratic Programming (QP) method. Numerical simulations are carried out to demonstrate the feasibility and effectiveness of the proposed integrated identification and control method.

  8. Reuse of reclaimed wastewater for golf course irrigation in Tunisia.

    Science.gov (United States)

    Bahri, A; Basset, C; Oueslati, F; Brissaud, F

    2001-01-01

    In Tunisia, golf courses are irrigated with secondary treated effluent stored in landscape impoundments. The impact of the conveyance and storage steps on the physical-chemical and biological quality of irrigation water was evaluated on three golf courses over two years. It was found that the water quality varies all along the water route, from the wastewater treatment plant up to the irrigation site: nutrient and bacteria contents decreased along the route in the three cases. This variation depends on the wastewater quality, the length of the pipes conveying water, the number of regulation reservoirs and ponds, the water residence time in pipes, reservoirs and ponds, and the operation of the ponds. The bacteriological quality of irrigation water deteriorates during the irrigation period in the three golf courses as the ponds are operated as continuous flow reactors. The results obtained in this study indicate the inability of golf water supplies, as currently managed, to properly sanitize reclaimed wastewater and meet target quality criteria recommended by WHO (1989) for water intended for recreational use. For a safe reuse of reclaimed wastewater for golf course irrigation, changes in the design and operation of the ponds should be planned or additional treatment steps provided.

  9. Accumulation of Cd in agricultural soil under long-term reclaimed water irrigation

    International Nuclear Information System (INIS)

    Chen, Weiping; Lu, Sidan; Peng, Chi; Jiao, Wentao; Wang, Meie

    2013-01-01

    Safety of agricultural irrigation with reclaimed water is of great concern as some potential hazardous compounds like heavy metals may be accumulated in soils over time. Impacts of long-term reclaimed water on soil Cd pollution were evaluated based on the field investigation in two main crop areas in Beijing with long irrigation history and on simulation results of STEM-profile model. Under long-term reclaimed water, Cd content in the top 20 cm soil layer was greatly elevated and was more than 2 times higher than that in the deep soil layer. There was very small differences between the field measured and model simulated Cd content in the plow layer (top 20 cm) and entire soil layer. Long-term model prediction showed that reclaimed water irrigation had a low environmental risk of soil Cd pollution, but the risk would be aggravated when there were high metal loading from other sources. The risk is also depending on the soil and plant properties. -- Highlights: •Root zone soil Cd content was elevated by one time under long-term reclaimed water irrigation. •The STEM-profile model can well track the Cd balance in the soil profile. •Reclaimed water irrigation plays a limited role on soil Cd accumulation in Beijing croplands. -- There was a low risk of soil Cd pollution under long-term reclaimed water irrigation

  10. Social Acceptance for Reclaimed Water Use: A Case Study in Bengaluru

    Directory of Open Access Journals (Sweden)

    Chaya Ravishankar

    2018-01-01

    Full Text Available The main source of water to the peri-urban areas of Bengaluru is groundwater. Access to groundwater is through tankers, private borewells, Bruhat Bengaluru MahanagaraPalike (Urban Local Body borewells, and public stand posts. All modes other than tankers provide water to the community free of charge. Reclaimed water from sewage treatment plants (STPs is in use by industries and some gated communities and multistoried apartments for toilet flushing and landscaping. For individual households in peri-urban areas of Bengaluru, it could be an additional water source replacing expensive water supply through tankers; reducing demand for groundwater (a finite resource; improving the sanitation system by providing drainage systems and preventing groundwater contamination from black and grey water. Consequently, this research paper investigates the willingness of residents in peri-urban areas of Bengaluru to use reclaimed water for non-potable end uses. To investigate residents’ willingness and key motivations for the use of reclaimed water, a survey of residents in the peri-urban ward of Bellandur was conducted. In this region, the sewerage board had prepared a media advertisement to create awareness of—and to sell—reclaimed water to other users, including local residents. This advertisement was shown to respondents, asking if they were willing to accept and buy the reclaimed water at 15 Indian Rupees (INR per kiloliter. Sixty-seven percent of residents who were household owners were willing to buy reclaimed water, 20% were concerned about hygiene, and 33% of respondents lacked trust in the public agency with respect to water quality standards. The study concludes that public awareness from key stakeholders is essential for the reuse of reclaimed water. It also recommends stringent regulation by levying fees for groundwater extraction in addition to making reclaimed water readily available and supplied free of charge to the consumers. In addition

  11. Performance of portland limestone cements: Cements designed to be more sustainable that include up to 15% limestone addition

    Science.gov (United States)

    Barrett, Timothy J.

    In 2009, ASTM and AASHTO permitted the use of up to 5% interground limestone in ordinary portland cement (OPC) as a part of a change to ASTM C150/AASHTO M85. When this work was initiated a new proposal was being discussed that would enable up to 15% interground limestone cement to be considered in ASTM C595/AASHTO M234. This work served to provide rapid feedback to the state department of transportation and concrete industry for use in discussions regarding these specifications. Since the time this work was initiated, ASTM C595/AASHTO M234 was passed (2012c) and PLCs are now able to be specified, however they are still not widely used. The proposal for increasing the volume of limestone that would be permitted to be interground in cement is designed to enable more sustainable construction, which may significantly reduce the CO2 that is embodied in the built infrastructure while also extending the life of cement quarries. Research regarding the performance of cements with interground limestone has been conducted by the cement industry since these cements became widely used in Europe over three decades ago, however this work focuses on North American Portland Limestone Cements (PLCs) which are specifically designed to achieve similar performance as the OPCs they replace.This thesis presents a two-phase study in which the potential for application of cements containing limestone was assessed. The first phase of this study utilized a fundamental approach to determine whether cement with up to 15% of interground or blended limestone can be used as a direct substitute to ordinary portland cement. The second phase of the study assessed the concern of early age shrinkage and cracking potential when using PLCs, as these cements are typically ground finer than their OPC counterparts. For the first phase of the study, three commercially produced PLCs were obtained and compared to three commercially produced OPCs made from the same clinker. An additional cement was tested

  12. Are the Vinjamur rocks carbonatites or meta-limestones?

    Energy Technology Data Exchange (ETDEWEB)

    Subbarao, K V; Bhaskar Rao, B [Indian Institute of Technology, Bombay (India). Dept. of Earth Sciences; Le Bas, M J [Univ. of Leicester, Leicester (United Kingdom). Dept. of Geology

    1995-08-01

    New whole-rock rare earth element (REE) data for the metacarbonate rocks inter bedded with schists at Vinjamur in the Nellore schist belt of Andhra Pradesh, show low total REE contents ({sigma}9-128 ppm) that are inconsistent with an igneous carbonatitic origin but which correspond more closely with a sedimentary limestone origin. The REE data of these rocks however, do not give absolute discrimination between marbles of meta-limestone and metacarbonatite origin. Micro-probe analytical data give better discrimination, and the chemical compositions of the calcite, micas, amphibole, plagioclase, apatite, monazite and staurolite in the Vinjamur marbles give strong and consistent evidence of a metamorphosed sedimentary rather than an igneous origin. (author). 35 refs., 7 figs., 9 tabs.

  13. The influence of combustion derived pollutants on limestone deterioration

    DEFF Research Database (Denmark)

    Johnson, JB; Montgomery, Melanie; Thompson, GE

    1996-01-01

    This study concerns quantification of the relative chemical degradation effects of dry deposition of combustion-derived atmospheric pollutants, HCl, SO2 and NO2, on Portland and Monks Park limestones, employing laboratory exposure chambers for periods of 30 days. Using presentation rates up to 40 x...... 10(-4) mu g cm(-2) s(-1), the pollutants were assessed individually and in various combinations, along with ozone as oxidant, at 84% RH with dry or water-wetted surfaces. The degradation was followed by analysis of exposed stone, for Cl-, SO42- and NO3-, and of run-off solution for Ca2+, in addition...... to the anions. From these data, the total calcium released from limestone to reaction ions and products and the percentages of each pollutant reacted (and so the deposition velocity (V-D)) in each exposure regime were calculated. HCl acted independently of the presence of other pollutants, showed 40 and 100...

  14. Induration and Biot’s Coefficient of Palaeogene Limestone

    DEFF Research Database (Denmark)

    Andreassen, Katrine Alling

    2017-01-01

    In engineering geology and classification of rock masses for civil engineering purposes, the degree of induration for a rock serves as a useful classification parameter. Induration is a measure of how well the grains of a sedimentary rock are cemented together - from loosely cemented/soft rock...... to very competent/slightly metamorphic rock. The Biot coefficient links to the degree of cementation in the capacity of how it relates the elastic deformations with the change in pore pressure. A hypothesis is that the degree of induration could be correlated to the magnitude of the Biot coefficient....... This is tested on 11 Copenhagen Limestone specimens of varying porosity and densities obtained from one borehole with a limestone interval of 30 m. Their induration varies from H2 to H5. Elastic wave propagation measurements are used to establish the Biot coefficient and determination of the mineralogy for H5...

  15. Are the Vinjamur rocks carbonatites or meta-limestones?

    International Nuclear Information System (INIS)

    Subbarao, K.V.; Bhaskar Rao, B.; Le Bas, M.J.

    1995-01-01

    New whole-rock rare earth element (REE) data for the metacarbonate rocks inter bedded with schists at Vinjamur in the Nellore schist belt of Andhra Pradesh, show low total REE contents (σ9-128 ppm) that are inconsistent with an igneous carbonatitic origin but which correspond more closely with a sedimentary limestone origin. The REE data of these rocks however, do not give absolute discrimination between marbles of meta-limestone and metacarbonatite origin. Micro-probe analytical data give better discrimination, and the chemical compositions of the calcite, micas, amphibole, plagioclase, apatite, monazite and staurolite in the Vinjamur marbles give strong and consistent evidence of a metamorphosed sedimentary rather than an igneous origin. (author). 35 refs., 7 figs., 9 tabs

  16. OPTIMALIZATION OF BLASTING IN »LAKOVIĆI« LIMESTONE QUARRY

    OpenAIRE

    Branko Božić; Karlo Braun

    1992-01-01

    The optimalization of exploitation in »Lakovići« limestone quarry is described. Based on determined discontinuities in the rock mass and their densities, the best possible working site have been located in order to obtain the best possible sizes of blasted rocks and work slope stability. Optimal lowest resistance line size for the quarry has been counted and proved experimentally. New blasting parameters have resulted in considerable saving of drilling and explosive (the paper is published in...

  17. Degradation behavior of limestone concrete under limited time sodium exposure

    International Nuclear Information System (INIS)

    Das, S.K.; Sharma, A.K.; Ramesh, S.S.; Parida, F.C.; Kasinathan, N.; Chellapandi, P.

    2009-01-01

    Adequate safety measures are taken during design, fabrication, construction and operation of liquid sodium cooled fast breeder reactor (FBR). However, possibility of sodium leak from secondary heat transport circuits of FBR has not been completely ruled out. In the areas housing sodium pipelines such as Steam Generator Building (SGB), spilled liquid sodium not only reacts with air causing fire but also interacts with structural concrete resulting in its degradation. The structural concrete can be protected from sodium attack using sodium resistant sacrificial concrete layer or steel/refractory liners. Moreover, design and construction of sloping floor with sodium collection pit helps in minimizing the mass of sodium accumulated on the floor and exposure period. Sacrificial concrete layer on the structural concrete should meet key factors like economy, castability, easy removal of affected concrete in the event of a sodium fire and disposability of debris apart from its good resistance against hot burning sodium. Present study is directed towards testing of limestone concrete blocks (made out of 13% ordinary portland cement, 8% water, 48% coarse limestone and 31 % fine limestone aggregates)

  18. Development of gypsum alteration on marble and limestone

    Science.gov (United States)

    McGee, E.S.

    1996-01-01

    Blackened alteration crusts of gypsum plus particulates that form on sheltered areas on marble and limestone buildings pose a challenge for rehabilitation and cleaning. Fresh marble and limestone samples exposed at monitored exposure sites present conditions of simple geometry and well-documented exposures but have short exposure histories (one to five years). The gypsum alteration crusts that develop on these samples provide insight into the early stages and rate of alteration crust formation. Alteration crusts from buildings give a longer, but less well known exposure history and present much more complex surfaces for gypsum accumulation. Integrated observations and measurements of alteration crusts from exposure samples and from buildings identify four factors that are important in the formation and development of alteration crusts on marble and limestone: (1) pollution levels, (2) exposure to rain or washing, (3) geometry of exposure of the stone surface, and (4) permeability of the stone. The combination of these factors contributes to both the distribution and the physical characteristics of the gypsum crusts which may affect cleaning decisions.

  19. Biogenic magnetite as a primary remanence carrier in limestone deposits

    Science.gov (United States)

    Chang, Shih-Bin R.; Kirschvink, Joseph L.; Stolz, John F.

    1987-06-01

    Studies on the microbial communities and magnetic phases of samples collected from carbonate oozes at Sugarloaf Key, FL, U.S.A. and calcareous laminated sediments from Laguna Figueroa, Baja California, Mexico have revealed the existence of magnetotactic bacteria and ultrafine-grained single domain magnetite in both environments. Magnetotactic bacteria were identified by light and electron microscopy. The single domain magnetite was detected by coercivity spectra analysis with a SQUID magnetometer and examined under the transmission electron microscope. The similarity, in terms of size and shape, between the single domain magnetite found in these sediments and the magnetite observed in the bacterial magnetosome from enriched cultures indicates the ultrafine-grained magnetite in these two marine environments was biologically formed. These results, combined with the common occurrences of ultrafine-grained magnetite in limestone deposits detected rock magnetically, suggest biogenic magnetite may be present and contribute to the magnetic remanence in these rocks. Several Cambrian limestone samples, separately collected from Siberia, China, and Kazakhstan, were examined for the presence of bacterial magnetite. Samples from the Lower Cambrian Sinskian Formation at Siberia Platform were found to contain both a large amount of apparently bacterial magnetite particles and a very stable primary magnetic component. Post-Cambrian diagenesis does not seem to affect the microgranulometry of these apparently bacterial magnetite crystals or the magnetic remanence carried by them. Assessing the potential role of biogenic magnetite as a primary remanence carrier in other Phanerozoic limestone deposits ought to be further pursued.

  20. The Biot coefficient for a low permeability heterogeneous limestone

    Science.gov (United States)

    Selvadurai, A. P. S.

    2018-04-01

    This paper presents the experimental and theoretical developments used to estimate the Biot coefficient for the heterogeneous Cobourg Limestone, which is characterized by its very low permeability. The coefficient forms an important component of the Biot poroelastic model that is used to examine coupled hydro-mechanical and thermo-hydro-mechanical processes in the fluid-saturated Cobourg Limestone. The constraints imposed by both the heterogeneous fabric and its extremely low intact permeability [K \\in (10^{-23},10^{-20}) m2 ] require the development of alternative approaches to estimate the Biot coefficient. Large specimen bench-scale triaxial tests (150 mm diameter and 300 mm long) that account for the scale of the heterogeneous fabric are complemented by results for the volume fraction-based mineralogical composition derived from XRD measurements. The compressibility of the solid phase is based on theoretical developments proposed in the mechanics of multi-phasic elastic materials. An appeal to the theory of multi-phasic elastic solids is the only feasible approach for examining the compressibility of the solid phase. The presence of a number of mineral species necessitates the use of the theories of Voigt, Reuss and Hill along with the theories proposed by Hashin and Shtrikman for developing bounds for the compressibility of the multi-phasic geologic material composing the skeletal fabric. The analytical estimates for the Biot coefficient for the Cobourg Limestone are compared with results for similar low permeability rocks reported in the literature.

  1. Thermal and chemical interaction of hot liquid sodium with limestone concrete in argon atmosphere

    International Nuclear Information System (INIS)

    Fakir, Charan Parida; Sanjay, Kumar Das; Anil, Kumar Sharma; Ramesh, S.S.; Somayajulu, P.A.; Malarvizhi, B.; Kasinathan, N.; Rajan, M.

    2007-01-01

    Sodium cooled fast breeder reactors (FBRs) may experience accidental leakage of hot liquid sodium in the inert equipment cells and reactor cavity. The leaked sodium at temperature ranging from 120degC to 550degC can come in contact with the sacrificial layer of limestone concrete. In order to study the thermal and chemical impact of sodium on the limestone concrete, five experimental runs were carried out under different test conditions simulating accident scenarios as realistically as possible. In each experimental run, a given mass of liquid sodium preheated to a specified temperature was dumped on the surface of concrete specimen housed in a test vessel with argon atmosphere. The sodium pool formed on the concrete was heated with an immersion heater to maintain the pool temperature at pre-selected level. The temperatures at various strategic locations were continuously monitored throughout the test run. Online measurement of pressure, hydrogen gas and oxygen gas in argon atmosphere was conducted. The solid samples of sodium debris were retrieved from the posttest concrete specimen by manual core drilling device for chemical analysis of reacted and un-reacted sodium. After cleaning the sodium debris, a power-drilling machine was employed to collect powder samples at regular depth interval from the concrete block floor to determine residual free and bound water. This paper presents some of the dominant thermal and chemical features related to structural safety of the concrete. Among the thermal parameters, on-set time and residence period for Energetic Thermal Transients (ETT) along with peak and average heat generation rates are evaluated. Chemical parameters such as rate and extent of water release from concrete, sodium consumption, sodium hydroxide production and sodium emission into argon atmosphere are also elucidated. Physicochemical characteristics of post-test sodium and concrete debris were investigated. Moreover spatial distribution of sodium, free and

  2. Studies on the effects of air pollution on limestone degradation in Great Britain

    Science.gov (United States)

    Webb, A. H.; Bawden, R. J.; Busby, A. K.; Hopkins, J. N.

    The CEGB and the Cathedrals Advisory Commission for England formed a Joint Working Party in 1985 to promote a research programme aimed at improving the understanding of the relationships between stone decay, atmospheric pollution and other factors. The programme has included exposure of limestone samples at York Minster and eight other sites in England and Scotland selected to give a mix of urban, marine and rural locations. All of the sites have comprehensive air pollution and meteorological monitoring and measurement of rainfall chemistry. At two sites samples have been fumigated with controlled levels of sulphur dioxide. Over all sites, there was a significant trend to increased weight loss with increase in average sulphur dioxide concentration, but a negative trend with total nitrogen oxides and with nitrogen dioxide. For sample exposures longer than 200 days, the sulphur dioxide dependence at the inland Liphook fumigation site was about half that found near the coast at Littlehampton. There was no significant trend to increase weight loss with total rainfall amount for the complete data set, but the analysis was dominated by the very wet Scottish site, which experienced the lowest average concentrations of air pollutants. A theoretical model for the chemical dissolution of rainwashed limestone has been derived from consideration of the ion and mass balances between the incident rain water and run-off water. The model has been fitted to the measured loss rates from the stonework field trials. With the exception of the very wet Scottish site, the difference between the stone loss rate, calculated from the model, and the mean measured loss rate for any particular exposure was generally smaller than the variation between the triplicate samples. Variation in the dry deposition velocity between sites and exposure periods does not appear to have been a very significant factor, and no residual effect due to the concentrations of nitrogen oxides was found. The natural

  3. The reclaiming of online media by civil society

    DEFF Research Database (Denmark)

    Galis, Vasilis; Neumayer, Christina

    as the oxymoron of radical activists on the left using capitalist media platforms and how this influences their political identity. Therefore, there is a need to understand the cyber-material impact of online media on collective action initiated by civil society as well as the relationship between ideological......In light of the financial crisis and harsher migration policies, actions initiated by radical civil society groups are on the rise. This project argues that in this time it is important to understand the reclaiming of online media by civil society. To reach this understanding we will explore how...... activists of the radical left have mobilized protests and solidarity actions through online media. We have chosen to locate our study in Sweden and Greece. Greece has found itself in the eye of the global financial storm whereas Sweden is coming out of the recession more favorably. In general...

  4. Theorizing Critical Placemaking as a Tool for Reclaiming Public Space.

    Science.gov (United States)

    Toolis, Erin E

    2017-03-01

    As economic inequality and segregation continue to grow in the U.S., psychology has an important role to play in exploring and promoting processes that can disrupt social injustice. This paper identifies the privatization of public space as a social problem that contributes to the entrenchment of social, economic, and racial inequality, and advances "critical placemaking" as a tool for reclaiming public space for public use. Drawing from key concepts in environmental psychology, narrative psychology, and community psychology, the proposed framework seeks to theorize the processes by which placemaking may contribute to transforming community narratives and building more inclusive, participatory, and democratic communities. Policy implications and future directions for empirical work are discussed. © Society for Community Research and Action 2017.

  5. Reclaiming native forest ecosystems in the oilsands region

    International Nuclear Information System (INIS)

    Tuttle, S.

    1997-01-01

    Suncor Energy's land reclamation objectives were reviewed. The general objective is to construct waste dumps and tailings impoundment structures in such a way that they can be transformed into stable landforms with maintenance-free, self-sustaining ecosystems that have at least the same capability to support life as they had during their pre-disturbed condition. In the case of Suncor's current and proposed oilsands mining, this means returning the land to upland forest for the most part. Some of the reclaimed land will become wetlands with some open water areas. Current reclamation and tree planting methods result in a diverse herbaceous cover developing within a year of soil amendment application. These vegetative communities are capable of providing erosion protection, as well as serving as a source of food and cover for wildlife, and generally meeting the reclamation goal of maintenance-free, self-sustaining ecosystems

  6. Infiltration of surface mined land reclaimed by deep tillage treatments

    International Nuclear Information System (INIS)

    Chong, S.K.; Cowsert, P.

    1994-01-01

    Surface mining of coal leads to the drastic disturbance of soils. Compaction of replaced subsoil and topsoil resulting from hauling, grading, and leveling procedures produces a poor rooting medium for crop growth. Soil compaction results in high bulk density, low macroporosity, poor water infiltration capacity, and reduced elongation of plant roots. In the United States, Public Law 95-87 mandates that the rooting medium of mined soils have specific textural characteristics and be graded and shaped to a topography similar to premining conditions. Also, crop productivity levels equivalent to those prior to mining must be achieved, especially for prime farmland. Alleviation of compaction has been the major focus of reclamation, and recently new techniques to augment the rooting zone with deep-ripping and loosening equipment have come to the forefront. Several surface mine operators in the Illinois coal basin are using deep tillage equipment that is capable of loosening soils to greater depths than is possible with conventional farm tillage equipment. Information on the beneficial effects of these loosening procedures on soil hydrological properties, such as infiltration, runoff potential, erosion, and water retention, is extremely important for future mined land management. However, such information is lacking. In view of the current yield demonstration regulation for prime farmland and other unmined soils, it is important that as much information as possible be obtained concerning the effect of deep tillage on soil hydrologic properties. The objectives of this study are: (1) to compare infiltration rates and related soil physical properties of mined soils reclaimed by various deep tillage treatments and (2) to study the temporal variability of infiltration and related physical properties of the reclaimed mined soil after deep tillage treatment

  7. Influence of the Reclaim Addition on Properties of Moulding Sands with the Geopol Binder

    Directory of Open Access Journals (Sweden)

    Drożyński D.

    2015-03-01

    Full Text Available The investigation results of the influence of the reclaim additions on the properties of moulding sands with the GEOPOL geopolymer binder developed by the SAND TEAM Company were presented. Two brands of hardeners were applied in the tested compositions, the first one was developed by the SAND TEAM Company, marked SA72 and the new hardener offered by the KRATOS Company, marked KR72. The main purpose of investigations was to determine the influence of reclaim fractions and the applied hardener on the basic moulding sands properties, such as: bending and tensile strength, permeability and grindability. The unfavourable influence of the reclaim additions into moulding sands on the tested properties as well as an increased hardening rate, were found. Moulding sands, in which the hardener KR72 of the KRATOS Company was used, were less sensitive to the reclaim additions

  8. Feasibility of reclaimed asphalt pavement as aggregate in portland cement concrete pavement, phase II : field demonstration.

    Science.gov (United States)

    2015-10-01

    This research was focused on evaluating the feasibility of using minimally processed reclaimed asphalt pavement (RAP) as : aggregate replacement in concrete pavements. An initial phase of research demonstrated that concretes with up to 50 percent : o...

  9. Feasibility of reclaimed asphalt pavement as aggregate in portland cement concrete pavements.

    Science.gov (United States)

    2013-11-01

    This research effort was focused on evaluating the feasibility of using minimally processed reclaimed : asphalt pavement (RAP) as aggregate replacement in concrete pavements. This research demonstrated : that concretes with up to 50 percent of the fi...

  10. Residual stresses

    International Nuclear Information System (INIS)

    Macherauch, E.

    1978-01-01

    Residual stresses are stresses which exist in a material without the influence of external powers and moments. They come into existence when the volume of a material constantly changes its form as a consequence of mechanical, thermal, and/or chemical processes and is hindered by neighbouring volumes. Bodies with residual stress are in mechanical balance. These residual stresses can be manifested by means of all mechanical interventions disturbing this balance. Acoustical, optical, radiological, and magnetical methods involving material changes caused by residual stress can also serve for determining residual stress. Residual stresses have an ambivalent character. In technical practice, they are feared and liked at the same time. They cause trouble because they can be the cause for unexpected behaviour of construction elements. They are feared since they can cause failure, in the worst case with catastrophical consequences. They are appreciated, on the other hand, because, in many cases, they can contribute to improvements of the material behaviour under certain circumstances. But they are especially liked for their giving convenient and (this is most important) mostly uncontrollable explanations. For only in very few cases we have enough knowledge and possibilities for the objective evaluation of residual stresses. (orig.) [de

  11. Enabling In-Theater Processes for Indigenous, Recycled, and Reclaimed Material Manufacturing

    Science.gov (United States)

    2015-12-01

    plastic , chemicals, food, cloth , oil, grease, biological materials, animal and agricultural waste, and sludge. It is expected that one of these...ARL-TR-7560 ● DEC 2015 US Army Research Laboratory Enabling In-Theater Processes for Indigenous, Recycled , and Reclaimed Material...ARL-TR-7560 ● DEC 2015 US Army Research Laboratory Enabling In-Theater Processes for Indigenous, Recycled , and Reclaimed Material

  12. Porous ceramic membrane with superhydrophobic and superoleophilic surface for reclaiming oil from oily water

    Science.gov (United States)

    Su, Changhong; Xu, Youqian; Zhang, Wei; Liu, Yang; Li, Jun

    2012-01-01

    A porous ceramic tube with superhydrophobic and superoleophilic surface was fabricated by sol-gel and then surface modification with polyurethane-polydimethysiloxane, and an oil-water separator based on the porous ceramic tube was erected to characterize superhydrophobic and superoleophilic surface's separation efficiency and velocity when being used to reclaim oil from oily water and complex oily water containing clay particle. The separator is fit for reclaiming oil from oily water.

  13. A Remote Sensing Approach to Environmental Monitoring in a Reclaimed Mine Area

    OpenAIRE

    Rajchandar Padmanaban; Avit K. Bhowmik; Pedro Cabral

    2017-01-01

    Padmanaban, R., Bhowmik, A. K., & Cabral, P. (2017). A Remote Sensing Approach to Environmental Monitoring in a Reclaimed Mine Area. ISPRS International Journal of Geo-Information, 6(12), 1-14. [401]. DOI: 10.3390/ijgi6120401 Mining for resources extraction may lead to geological and associated environmental changes due to ground movements, collision with mining cavities, and deformation of aquifers. Geological changes may continue in a reclaimed mine area, and the deformed aquifers may en...

  14. Geomorphic evaluation of erosional stability at reclaimed surface mines in northwestern Colorado. Water Resources Investigation

    International Nuclear Information System (INIS)

    Elliott, J.G.

    1990-01-01

    The report identifies geomorphic, pedologic, vegetation, and hydrologic conditions that are associated with erosion of reclaimed surface-mined lands in northwestern Colorado. The report also presents methods for determining the appropriate values of geomorphic variables that can be manipulated during reclamation to increase erosional stability. A section on geomorphic principles associated with erosion of reclaimed land surfaces is designed for use as a primer by mine personnel and reclamation planners. The areas of interest in the study were those that were reclaimed under jurisdiction of current (1988) SMCRA reclamation regulations, yet were still affected by relatively rapid erosion rates several years after reclamation activities were completed. Geomorphic, pedologic, vegetation, and hydrologic data were collected onsite and from topographic maps. Data from reclaimed areas undergoing accelerated erosion were compared with data from reclaimed areas undergoing minimal erosion to identify conditions that controlled erosion on reclaimed surface-mined lands and to identify some postmining equilibrium landform characteristics. These data also were used to develop threshold relations

  15. Influence of Reclamation Process on the Ecological Quality of Reclaim Sand

    Directory of Open Access Journals (Sweden)

    Dereń M.

    2017-12-01

    Full Text Available In this article, there were presented results of research on influence of reclamation process on the ecological quality of reclaim sand with furan resin used in nonferrous foundry. The quality of reclaimed sand is mainly define by two group of chemical substances from elution of reclaimed sand: Dissolves Organic Carbon (DOC and Total Dissolves Solids (TDS. Reclaimed sand used in test was prepared in experimental thermal reclaimer and mechanical vibration reclaimer REGMAS installed in Faculty of Foundry Engineering at University Of Science and Technology in Krakow. The reference point is molding sand shaking out and crumble in jaw crusher. Test of elution was made in accredited laboratory in Center For Research and Environmental Control in Katowice up to the standard with Dissolves Organic Carbon (DOC - PN-EN 1484:1999; Total Dissolves Solids (TDS - PN-EN 15216:2010. The standard for elution test is PN-EN 12457- 4:2006. Except that we were made loss of ignition test, to check how many resin was rest on sand grains.

  16. Soil organic carbon of an intensively reclaimed region in China: Current status and carbon sequestration potential.

    Science.gov (United States)

    Deng, Xunfei; Zhan, Yu; Wang, Fei; Ma, Wanzhu; Ren, Zhouqiao; Chen, Xiaojia; Qin, Fangjin; Long, Wenli; Zhu, Zhenling; Lv, Xiaonan

    2016-09-15

    Land reclamation has been highly intensive in China, resulting in a large amount of soil organic carbon (SOC) loss to the atmosphere. Evaluating the factors which drive SOC dynamics and carbon sequestration potential in reclaimed land is critical for improving soil fertility and mitigating global warming. This study aims to determine the current status and factors important to the SOC density in a typical reclaimed land located in Eastern China, where land reclamation has been undergoing for centuries. A total of 4746 topsoil samples were collected from 2007 to 2010. The SOC density of the reclaimed land (3.18±0.05kgCm(-2); mean±standard error) is significantly lower than that of the adjacent non-reclaimed land (5.71±0.04kgCm(-2)) (pcarbon sequestration potential of the reclaimed lands may achieve a maximum of 5.80±1.81kgCO2m(-2) (mean±SD) when dryland is converted to flooded land with vegetable-rice cropping system and soil pH of ~5.9. Note that in some scenarios the methane emission substantially offsets the carbon sequestration potential, especially for continuous rice cropping system. With the optimal setting for carbon sequestration, it is estimated that the dryland reclaimed in the last 50years in China is able to sequester 0.12milliontons CO2 equivalent per year. Copyright © 2016 Elsevier B.V. All rights reserved.

  17. Kinetic Hydration Heat Modeling for High-Performance Concrete Containing Limestone Powder

    Directory of Open Access Journals (Sweden)

    Xiao-Yong Wang

    2017-01-01

    Full Text Available Limestone powder is increasingly used in producing high-performance concrete in the modern concrete industry. Limestone powder blended concrete has many advantages, such as increasing the early-age strength, reducing the setting time, improving the workability, and reducing the heat of hydration. This study presents a kinetic model for modeling the hydration heat of limestone blended concrete. First, an improved hydration model is proposed which considers the dilution effect and nucleation effect due to limestone powder addition. A degree of hydration is calculated using this improved hydration model. Second, hydration heat is calculated using the degree of hydration. The effects of water to binder ratio and limestone replacement ratio on hydration heat are clarified. Third, the temperature history and temperature distribution of hardening limestone blended concrete are calculated by combining hydration model with finite element method. The analysis results generally agree with experimental results of high-performance concrete with various mixing proportions.

  18. Simultaneous removal of several heavy metals from aqueous solution by natural limestones

    Directory of Open Access Journals (Sweden)

    Sdiri A.

    2014-07-01

    Full Text Available Four natural limestone samples, collected from the Campanian-Maastrichtian limestones, Tunisia, were used as adsorbents for the removal of toxic metals in aqueous systems. The results indicated that high removal efficiency could be achieved by the present natural limestones. Among the metal ions studied, Pb2+ was the most preferably removed cation because of its high affinity to calcite surface. In binary system, the presence of Cu2+ effectively depressed the sorption of Cd2+ and Zn2+. Similarly Cu2+ strongly competed with Pb2+ to limestone surface. In ternary system, the removal further decreased, but considerable amount of Pb2+ and Cu2+ still occurred regardless of the limestone sample. The same behavior was observed in quadruple system, where the selectivity sequence was Pb2+ > Cu2+ > Cd2+ > Zn2+. From these results, it was concluded that the studied limestones have the required technical specifications to be used for the removal of toxic metals from wastewaters.

  19. OPTIMALIZATION OF BLASTING IN »LAKOVIĆI« LIMESTONE QUARRY

    Directory of Open Access Journals (Sweden)

    Branko Božić

    1992-12-01

    Full Text Available The optimalization of exploitation in »Lakovići« limestone quarry is described. Based on determined discontinuities in the rock mass and their densities, the best possible working site have been located in order to obtain the best possible sizes of blasted rocks and work slope stability. Optimal lowest resistance line size for the quarry has been counted and proved experimentally. New blasting parameters have resulted in considerable saving of drilling and explosive (the paper is published in Croatian.

  20. Penetration of molten core materials into basaltic and limestone concrete

    International Nuclear Information System (INIS)

    Sutherland, H.J.

    1978-01-01

    In conjunction with the small-scale, melt-concrete interaction tests being conducted at Sandia Laboratories, an acoustic technique has been used to monitor the penetration of molten core materials into basaltic and limestone concrete. Real time plots of the position of the melt/concrete interface have been obtained, and they illustrate that the initial penetration rate of the melt may be of the order of 80 mm/min. Phenomena deduced by the technique include a non-wetted melt/concrete interface

  1. Occurrence of vancomycin-resistant and -susceptible Enterococcus spp. in reclaimed water used for spray irrigation

    Energy Technology Data Exchange (ETDEWEB)

    Carey, Stephanie Ann; Goldstein, Rachel E. Rosenberg [Maryland Institute for Applied Environmental Health, University of Maryland School of Public Health, College Park, MD (United States); Gibbs, Shawn G. [Department of Environmental Health, School of Public Health-Bloomington, Indiana University, Bloomington, IN (United States); Claye, Emma [Maryland Institute for Applied Environmental Health, University of Maryland School of Public Health, College Park, MD (United States); He, Xin [Department of Epidemiology and Biostatistics, University of Maryland School of Public Health, College Park, MD (United States); Sapkota, Amy R., E-mail: ars@umd.edu [Maryland Institute for Applied Environmental Health, University of Maryland School of Public Health, College Park, MD (United States)

    2016-05-15

    Reclaiming municipal wastewater for agricultural, environmental, and industrial purposes is increasing in the United States to combat dwindling freshwater supplies. However, there is a lack of data regarding the microbial quality of reclaimed water. In particular, no previous studies have evaluated the occurrence of vancomycin-resistant enterococci (VRE) in reclaimed water used at spray irrigation sites in the United States. To address this knowledge gap, we investigated the occurrence, concentration, and antimicrobial resistance patterns of VRE and vancomycin-susceptible enterococci at three U.S. spray irrigation sites that use reclaimed water. We collected 48 reclaimed water samples from one Mid-Atlantic and two Midwest spray irrigation sites, as well as their respective wastewater treatment plants, in 2009 and 2010. Samples were analyzed for total enterococci and VRE using standard membrane filtration. Isolates were purified and then confirmed using biochemical tests and PCR. Antimicrobial susceptibility testing was conducted using the Sensititre® microbroth dilution system. Data were analyzed by two-sample proportion tests and one-way analysis of variance. We detected total enterococci and VRE in 71% (34/48) and 4% (2/48) of reclaimed water samples, respectively. Enterococcus faecalis was the most common species identified. At the Mid-Atlantic spray irrigation site, UV radiation decreased total enterococci to undetectable levels; however, subsequent storage in an open-air pond at this site resulted in increased concentrations of enterococci. E. faecalis isolates recovered from the Mid-Atlantic spray irrigation site expressed intrinsic resistance to quinupristin/dalfopristin; however, non-E. faecalis isolates expressed resistance to quinupristin/dalfopristin (52% of isolates), vancomycin (4%), tetracycline (13%), penicillin (4%) and ciprofloxacin (17%). Our findings show that VRE are present in low numbers in reclaimed water at point-of-use at the sampled spray

  2. Occurrence of vancomycin-resistant and -susceptible Enterococcus spp. in reclaimed water used for spray irrigation

    International Nuclear Information System (INIS)

    Carey, Stephanie Ann; Goldstein, Rachel E. Rosenberg; Gibbs, Shawn G.; Claye, Emma; He, Xin; Sapkota, Amy R.

    2016-01-01

    Reclaiming municipal wastewater for agricultural, environmental, and industrial purposes is increasing in the United States to combat dwindling freshwater supplies. However, there is a lack of data regarding the microbial quality of reclaimed water. In particular, no previous studies have evaluated the occurrence of vancomycin-resistant enterococci (VRE) in reclaimed water used at spray irrigation sites in the United States. To address this knowledge gap, we investigated the occurrence, concentration, and antimicrobial resistance patterns of VRE and vancomycin-susceptible enterococci at three U.S. spray irrigation sites that use reclaimed water. We collected 48 reclaimed water samples from one Mid-Atlantic and two Midwest spray irrigation sites, as well as their respective wastewater treatment plants, in 2009 and 2010. Samples were analyzed for total enterococci and VRE using standard membrane filtration. Isolates were purified and then confirmed using biochemical tests and PCR. Antimicrobial susceptibility testing was conducted using the Sensititre® microbroth dilution system. Data were analyzed by two-sample proportion tests and one-way analysis of variance. We detected total enterococci and VRE in 71% (34/48) and 4% (2/48) of reclaimed water samples, respectively. Enterococcus faecalis was the most common species identified. At the Mid-Atlantic spray irrigation site, UV radiation decreased total enterococci to undetectable levels; however, subsequent storage in an open-air pond at this site resulted in increased concentrations of enterococci. E. faecalis isolates recovered from the Mid-Atlantic spray irrigation site expressed intrinsic resistance to quinupristin/dalfopristin; however, non-E. faecalis isolates expressed resistance to quinupristin/dalfopristin (52% of isolates), vancomycin (4%), tetracycline (13%), penicillin (4%) and ciprofloxacin (17%). Our findings show that VRE are present in low numbers in reclaimed water at point-of-use at the sampled spray

  3. Coralgal facies of the Upper Eocene-Lower Oligocene limestones in Letca-Rastoci area

    Directory of Open Access Journals (Sweden)

    Ioana Prica

    2001-09-01

    Full Text Available In this paper are described the coralgal facies identified in the Upper Eocene-Lower Oligocene limestone succession (Cozla Formation outcropping in two quarries at Letca and Rastoci (Sălaj district, Romania. In the studied profiles the coral and algae limestones are interlayered with bioclastic limestones with foraminifera. On the top of relatively deep water deposits, coral and algae crusts and dendritic corals coated by algae were deposited. The environment registered a gradual deepening, the deposits being completely immersed, while bioclastic limestones with foraminifera were recurrently formed. This cycle is repeated, the whole succession being caracterized by several such “parasequences”.

  4. Modelling of Limestone Dissolution in Wet FGD Systems: The Importance of an Accurate Particle Size Distribution

    DEFF Research Database (Denmark)

    Kiil, Søren; Johnsson, Jan Erik; Dam-Johansen, Kim

    1999-01-01

    Danish limestone types with very different particle size distributions (PSDs). All limestones were of a high purity. Model predictions were found to be qualitatively in good agreement with experimental data without any use of adjustable parameters. Deviations between measurements and simulations were...... attributed primarily to the PSD measurements of the limestone particles, which were used as model inputs. The PSDs, measured using a laser diffrac-tion-based Malvern analyser, were probably not representative of the limestone samples because agglomeration phenomena took place when the particles were...

  5. Accelerated weathering of limestone for CO2 mitigation: Opportunities for the stone and cement industries

    Science.gov (United States)

    Langer, William H.; San, Juan A.; Rau, Greg H.; Caldeira, Ken

    2009-01-01

    Large amounts of limestone fines co-produced during the processing of crushed limestone may be useful in the sequestration of carbon dioxide (CO2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point sources such as cement manufacturing. AWL reactants are readily available, inexpensive and environmentally benign. Waste CO2 is hydrated with water to produce carbonic acid. This reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate.

  6. Techniques for Source Zone and Plume Characterization of Tetrachloroethene in Fractured Limestone Aquifers

    DEFF Research Database (Denmark)

    Fjordbøge, Annika Sidelmann; Mosthaf, Klaus; Janniche, Gry S.

    Characterization of chlorinated solvents in fractured limestone aquifers is essential for proper development of site specific conceptual models and subsequent risk assessment and remediation. High resolution characterization is challenged by the difficulties involved in collection of intact core...... an improved conceptual understanding of contaminant transport. At both sites limestone cores were collected with significant core losses. The discrete quantification of chlorinated solvents in the retrieved limestone cores was compared to different FLUTe technologies at the DNAPL site and passive and active...... distribution compared to the data obtained by quantification of chlorinated solvents in the limestone cores....

  7. Northern bobwhite breeding season ecology on a reclaimed surface mine

    Science.gov (United States)

    Brooke, Jarred M.; Tanner, Evan P.; Peters, David C.; Tanner, Ashley M.; Harper, Craig A.; Keyser, Patrick D.; Clark, Joseph D.; Morgan, John J.

    2017-01-01

    Surface coal mining and subsequent reclamation of surface mines have converted large forest areas into early successional vegetative communities in the eastern United States. This reclamation can provide a novel opportunity to conserve northern bobwhite (Colinus virginianus). We evaluated the influence of habitat management activities on nest survival, nest-site selection, and brood resource selection on managed and unmanaged units of a reclaimed surface mine, Peabody Wildlife Management Area (Peabody), in west-central Kentucky, USA, from 2010 to 2013. We compared resource selection, using discrete-choice analysis, and nest survival, using the nest survival model in Program MARK, between managed and unmanaged units of Peabody at 2 spatial scales: the composition and configuration of vegetation types (i.e., macrohabitat) and vegetation characteristics at nest sites and brood locations (i.e., microhabitat). On managed sites, we also investigated resource selection relative to a number of different treatments (e.g., herbicide, disking, prescribed fire). We found no evidence that nest-site selection was influenced by macrohabitat variables, but bobwhite selected nest sites in areas with greater litter depth than was available at random sites. On managed units, bobwhite were more likely to nest where herbicide was applied to reduce sericea lespedeza (Lespedeza cuneata) compared with areas untreated with herbicide. Daily nest survival was not influenced by habitat characteristics or by habitat management but was influenced by nest age and the interaction of nest initiation date and nest age. Daily nest survival was greater for older nests occurring early in the breeding season (0.99, SE < 0.01) but was lower for older nests occurring later in the season (0.08, SE = 0.13). Brood resource selection was not influenced by macrohabitat or microhabitat variables we measured, but broods on managed units selected areas treated with herbicide to control sericea lespedeza

  8. [Health risk induced by estrogens during unplanned indirect potable reuse of reclaimed water from domestic wastewater].

    Science.gov (United States)

    Wu, Qian-Yuan; Shao, Yi-Ru; Wang, Chao; Sun, Yan; Hu, Hong-Ying

    2014-03-01

    The estrogenic endocrine disruptors in reclaimed water from domestic wastewater may induce health risks to human being, when reclaimed water is used for augmentation of drinking water unplannedly and indirectly. This study investigated changes in concentrations of estrone, estradiol, 17alpha-ethinyl estradiol, bisphenol A, nonylphenol and octylphenol in reclaimed water during the reuse of reclaimed water for augmentation to water source such as lakes and reservoir via river. Thereafter, health risk induced by estrogens during the resue of reclaimed water was evaluated. The concentration of estrogen in secondary effluent ranged 0.1-100 ng x L(-1). The highest concentrations of bisphenol A and nonylphenol reached up to 1-10 microg x L(-1). During the indirect reuse of reclaimed water as potable water, the dilution and degradation in river and lake, and the removal by drinking water treatment process could change the concentrations of estrogen. The non-carcinogenic risks of estrone, estradiol, bisphenol A, nonylphenol and octylphenol were lower than 1. When the hydraulic retention time of 17alpha-ethinyl estradiol (EE2) in lakes and reservoir was higher than 30 days, the non-carcinogenic risk of EE2 was lower than 1 in most cases. When the hydraulic retention time of EE2 in lakes and reservoir was less than 30 days and the percentages of reclaimed water in drinking water were higher than 50%, the non-carcinogenic risk induced by EE2 was higher than 1 in 20%-50% samples. This indicated that the risks of EE2 should be concerned.

  9. Golf Course Irrigation with Reclaimed Water in the Mediterranean: A Risk Management Matter

    Directory of Open Access Journals (Sweden)

    Miquel Salgot

    2012-04-01

    Full Text Available Controversy regarding the amount of water consumed or saved as a result of human activity is currently paramount in water-scarce areas. In recent decades, golf—a land and water consuming activity—has been implanted in several areas of the Mediterranean basin, where the scarcity of water resources is well-known. As a result, the use of conventional water resources for golf course irrigation is increasingly contested and its replacement by reclaimed water has become essential. This paper examines the wide range of issues involved in its use on golf courses, including hazards—due to the presence of microorganisms and pollutants—and the corresponding risks that can appear. The resulting biological, chemical and physical water quality concerns are analyzed. Legal aspects related to the use of reclaimed water are also discussed and good reuse practices are suggested, including a detailed examination of risk assessment procedures and tools through observation or chemical, physical and microbiological analysis. The HACCP system—which focuses on quality determination in water samples from relevant control points—is described in detail, as it is generally accepted as one of the most scientific ways to detect health problems on a golf course. The paper concludes that, given the increasing availability of treated and reclaimed water and the water needs of golf courses, the future development of the sport in areas without surplus water resources—such as the Mediterranean basin—will predictably depend upon the use of reclaimed water. In recent years, risk assessment or analysis has emerged as an essential tool to guarantee the application of reclaimed water at an acceptable risk level. There certainly have been considerable advances and improvements in the tools that guarantee the safe use of reclaimed water, although current methods available require simplification for their practical application. Nevertheless, protocols applied at present

  10. The effect of water on the sulphation of limestone

    Energy Technology Data Exchange (ETDEWEB)

    Chunbo Wang; Lufei Jia; Yewen Tan; E.J. Anthony [North China Electric Power University, Baoding City (China). School of Energy and Power Engineering

    2010-09-15

    A series of tests was conducted in a thermogravimetric analyzer (TGA) to study the sulphation behaviour of limestone in the presence of water over the temperature range of 800-850{sup o}C. Four different Canadian limestones, all with a particle size range of 75-425 {mu}m, were sulphated using a synthetic flue gas with a composition of 15% CO{sub 2}, 3% O{sub 2}, 0% or 10% H{sub 2}O, 1750 ppm SO{sub 2} and the balance N{sub 2}. Water was shown to have a significant promotional effect on sulphation, especially in the diffusion-controlled stage. However, the effect of water during the kinetic-controlled stage appeared to be much less pronounced. Based on these results, it is proposed that the presence of water leads to the transient formation of Ca(OH){sub 2} as an intermediate, which in turn reacts with SO{sub 2} at a faster rate than CaO does. Alternatively stated, it appears that H{sub 2}O acts as catalyst for the sulphation reaction of CaO. 30 refs., 8 figs., 3 tabs.

  11. Laser removal of water repellent treatments on limestone

    Energy Technology Data Exchange (ETDEWEB)

    Gomez-Heras, Miguel; Alvarez de Buergo, Monica; Rebollar, Esther; Oujja, Mohamed; Castillejo, Marta; Fort, Rafael

    2003-12-15

    Protective and water repellent treatments are applied on stone materials used on buildings or sculptures of artistic value to reduce water intrusion without limiting the natural permeability to water vapour of the material. The effect of the wavelength associated with the laser removal of two water repellent treatments applied on limestone, Paraloid B-72, a copolymer of methyl acrylate and ethyl methacrylate, and Tegosivin HL-100, a modified polysiloxane resin, was investigated by using the four harmonics of a Q-switched Nd:YAG laser (1064, 532, 355 and 266 nm). The modifications induced on the surface of limestone samples by laser irradiation were studied using colorimetry, roughness measurements and scanning electron microscopy (SEM). The removal of the treatments was found to be dependent on the laser irradiation conditions and on the characteristics of the coatings. The fundamental laser radiation was effective in removing both treatments, but thermal alteration processes were induced on the constituent calcite crystals. The best results were obtained by irradiation in the near UV at 355 nm.

  12. Rare earths in the Leadville Limestone and its marble derivates

    International Nuclear Information System (INIS)

    Jarvis, J.C.; Wildeman, T.R.; Banks, N.G.

    1975-01-01

    Samples of unaltered and metamorphosed Leadville Limestone (Mississippian, Colorado) were analyzed by neutron activation for ten rare-earth elements (REE). The total abundance of the REE in the least-altered limestone is 4-12 ppm, and their distribution patterns are believed to be dominated by the carbonate minerals. The abundances of the REE in the marbles and their sedimentary precursors are comparable but the distribution patterns are not. Eu is enriched over the other REE in the marbles, and stratigraphically upward in the formation (samples located progressively further from the heat source), the light REE become less enriched relative to the heavy REE. The Eu anomaly is attributed to its ability, unique among the REE, to change from the 3+ to 2+ oxidation state. Whether this results in preferential mobilization of the other REE or whether this reflects the composition of the pore fluid during metamorphism is unknown. Stratigraphically selective depletion of the heavy REE may be attributed to more competition for the REE between fluid and carbonate minerals in the lower strata relative to the upper strata. This competition could have been caused by changes in the temperature of the pore fluid or to the greater resistance to solution of the dolomite in the lower parts of the formation than the calcite in the upper parts

  13. Solid residues

    International Nuclear Information System (INIS)

    Mulder, E.; Duin, P.J. van; Grootenboer, G.J.

    1995-01-01

    A summary is presented of the many investigations that have been done on solid residues of atmospheric fluid bed combustion (AFBC). These residues are bed ash, cyclone ash and bag filter ash. Physical and chemical properties are discussed and then the various uses of residues (in fillers, bricks, gravel, and for recovery of aluminium) are summarised. Toxicological properties of fly ash and stack ash are discussed as are risks of pneumoconiosis for workers handling fly ash, and contamination of water by ashes. On the basis of present information it is concluded that risks to public health from exposure to emissions of coal fly ash from AFBC appear small or negligible as are health risk to workers in the coal fly ash processing industry. 35 refs., 5 figs., 12 tabs

  14. Principal chemical properties of artificial soil composed of fly ash and furfural residue

    Energy Technology Data Exchange (ETDEWEB)

    Feng, Y.J.; Li, F.; Wang, X.L.; Liu, X.M.; Zhang, L.N. [Shandong Agricultural University, Tai An (China). College of Resources & Environments

    2006-10-15

    To solve soil shortage in reclaiming subsided land of coal mines, the principal chemical properties of artificial soil formed by mixing organic furfural residue and inorganic fly ash were examined. The results indicated that the artificial soil was suitable for agriculture use after irrigation and desalination, the available nutrients in the artificial soil could satisfy the growth demand of plants, and the pH tended to the neutrality.

  15. Importance of granulometry on phase evolution and phase-to-phase relationships of experimentally burned impure limestones intended for production of hydraulic lime and/or natural cement

    Science.gov (United States)

    Kozlovcev, Petr; Přikryl, Richard; Přikrylová, Jiřina

    2015-04-01

    In contrast to modern ordinary Portland cement production from finely ground raw material blends, ancient burning of hydraulic lime was conducted by burning larger pieces of natural raw material. Due to natural variability of raw material composition, exploitation of different beds from even one formation can result the product with significantly different composition and/or properties. Prague basin (Neoproterozoic to pre-Variscan Palaeozoic of the central part of the Bohemian Massif - the so-called Barrandian area, Czech Republic) represents a classical example of the limestone-rich region with long-term history of limestone burning for quick lime and/or various types of hydraulic binders. Due to the fact that burning of natural hydraulic lime has been abandoned in this region at the turn of 19th/20th c., significant gap in knowledge on the behavior of various limestone types and on the influence of minor variance in composition on the quality of burned product is encountered. Moreover, the importance of employment of larger pieces of raw material for burning for the development of proper phase-to-phase relationships (i.e. development of hydraulic phases below sintering temperature at mutual contacts of minerals) has not been examined before. To fill this gap, a representative specimens of major limestone types from the Prague basin have been selected for experimental study: Upper Silurian limestone types (Přídolí and Kopanina Lms.), and Lower Devonian limestones (Radotín, Kotýs, Řeporyje, Dvorce-Prokop, and Zlíchov Lms.). Petrographic character of the experimental material was examined by polarizing microscopy, cathodoluminescence, scanning electron microscopy with an energy dispersive spectrometer (SEM-EDS), and X-ray diffraction (XRD) of insoluble residue. Based on the data from wet silicate analyses, modal composition of studied impure limestones was computed. Experimental raw material was burned in laboratory electric furnace at 1000 and 1200°C for 3

  16. Effective Laboratory Method of Chromite Content Estimation in Reclaimed Sands

    Directory of Open Access Journals (Sweden)

    Ignaszak Z.

    2016-09-01

    Full Text Available The paper presents an original method of measuring the actual chromite content in the circulating moulding sand of foundry. This type of material is applied for production of moulds. This is the case of foundry which most frequently perform heavy casting in which for the construction of chemical hardening mould is used, both the quartz sand and chromite sand. After the dry reclamation of used moulding sand, both types of sands are mixed in various ratios resulting that in reclaimed sand silos, the layers of varying content of chromite in mixture are observed. For chromite recuperation from the circulating moulding sand there are applied the appropriate installations equipped with separate elements generating locally strong magnetic field. The knowledge of the current ratio of chromite and quartz sand allows to optimize the settings of installation and control of the separation efficiency. The arduous and time-consuming method of determining the content of chromite using bromoform liquid requires operational powers and precautions during using this toxic liquid. It was developed and tested the new, uncomplicated gravimetric laboratory method using powerful permanent magnets (neodymium. The method is used in the production conditions of casting for current inspection of chromite quantity in used sand in reclamation plant.

  17. A simple and proven technology for reclaiming acidic mine waters

    International Nuclear Information System (INIS)

    Bourke, Chris; Mack, Bernie

    2011-01-01

    The cost of water treatment is now more than ever a major consideration for maintaining an environmentally and economically sustainable mining operation. As an industry, we often have to consider water sources that are highly impure and difficult to treat. We are also discovering the value of our waste waters in this regard and using new and improved methods and technology to reclaim and reuse water. In many instances, the water or waste water to be treated is highly acidic and saturated in sparingly soluble salts. Conventional systems used to liberate this type of water typically involve high doses of lime with large volumes of waste sludge produced, and are comparatively complex to operate, to pretreat the water in order to reduce scaling tendency on the reverse osmosis stage. However, if the water is considered valuable for reuse, then why not avoid difficult and cumbersome pretreatment processes and treat the water at low pH to keep the sparingly soluble salts, metals and other dissolved species in solution. This paper describes a patented technology that uses and successfully proves this concept as a cost effective option for certain situations. Results from a treatability study on an Australian groundwater are discussed, along with an economic comparison to a conventional method and discussion on full-scale potential.

  18. EMISSION AND TRENDS IN RECLAIMING WASTE HEAT IN INDUSTRIAL INSTALATIONS

    Directory of Open Access Journals (Sweden)

    Lech Hys

    2013-04-01

    Full Text Available The article presents the analysis of waste heat emission in a typical industrial installation. On the basis of the process monitoring system, periodic analyses of fumes composition, installation process manual and the conducted measurements of the heat fluxes from individual sources emitting heat on the way of natural convection from the devices’ coats and forced convection in the fumes flux were calculated. According to the authors the heat of temperature 140–155 °C and surface power density 860–970 W/m2 emitted by devices’ covers can be reclaimed in ORC techniques, Peltier’s modules and the systems realising Stirling cycle. Part of the waste heat included in fumes, which makes c.a. 76% of the total emission from the installation, should be returned to the process of fuel oxidation, what will reduce the emission by c.a. 18% and the volume of consumed fuel by c.a. 25 m3 CH4/h, according to the presented calculations.

  19. Leaching of organic contaminants from storage of reclaimed asphalt pavement.

    Science.gov (United States)

    Norin, Malin; Strömvall, A M

    2004-03-01

    Recycling of asphalt has been promoted by rapid increases in both the use and price of petroleum-based bitumen. Semi-volatile organic compounds in leachates from reclaimed asphalt pavement, measured in field samples and in laboratory column test, were analysed through a GC/MS screen-test methodology. Sixteen PAH (polyaromatic hydrocarbons) were also analysed in leachates from the column study. The highest concentrations of semi-volatile compounds, approximately 400 microg l(-1), were measured in field samples from the scarified stockpile. Naphthalene, butylated hydroxytoluene (BHT) and dibutyl phthalate (DBP) were the most dominant of the identified semi-volatiles. The occurrence of these compounds in urban groundwater, also indicate high emission rates and persistent structures of the compounds, making them potentially hazardous. Car exhausts, rubber tires and the asphalt material itself are all probable emission sources, determined from the organic contaminants released from the stockpiles. The major leaching mechanism indicated was dissolution of organic contaminants from the surface of the asphalt gravels. In the laboratory column test, the release of high-molecular weight and more toxic PAH was higher in the leachates after two years than at the commencement of storage. The concentrations of semi-volatiles in leachates, were also several times lower than those from the field stockpile. These results demonstrate the need to follow up laboratory column test with real field measurements.

  20. What can offer us reclaimed landscape surrounding future lake Medard

    Energy Technology Data Exchange (ETDEWEB)

    Hrajnohova-Gillarova, H.; Kazmierski, T.; Martis, M. [Czech Univ. of Life Sciences, Prague (Czech Republic); Pecharova, E. [Czech Univ. of Life Sciences, Prague (Czech Republic); South-Bohemian Univ., Ceske Budejovice (Czech Republic)

    2010-07-01

    Soon after closing down a mine, the landscape that had been systematically disturbed by mining, should start to serve people from neighbouring towns and villages. This study characterized the Medard site located in the western part of the Czech Republic. The future Lake Medard includes the area of the former Medard-Libik Mine. Medard was an opencast brown coal mine, where mining finished in 2000 and reclamation plans involve its flooding until the year 2013. Forestry reclamation was also in progress. This paper presented a survey that was designed to help determine what the reclaimed landscape surrounding the future Lake Medard could offer. The paper provided background information on Medard Lake and outlined the methodology and results of the study. The methodology involved use of recent orthophotomaps, a study of the future lake Medard and data from the field survey. The study examined the long-term impacts on the social and environmental situation in the area. It was concluded that, once the reclamations are finished, there should be natural trails with information and educational infrastructure so that visitors to the area can learn about the places of interest. 17 refs., 6 figs.

  1. Design and verification of bituminous mixtures with the increased content of reclaimed asphalt pavement

    Science.gov (United States)

    Bańkowski, Wojciech; Król, Jan; Gałązka, Karol; Liphardt, Adam; Horodecka, Renata

    2018-05-01

    Recycling of bituminous pavements is an issue increasingly being discussed in Poland. The analysis of domestic and foreign experience indicates a need to develop this technology in our country, in particular the hot feeding and production technologies. Various steps are being taken in this direction, including research projects. One of them is the InnGA project entitled: “Reclaimed asphalt pavement: Innovative technology of bituminous mixtures using material from reclaimed asphalt pavement”. The paper presents the results of research involving the design of bituminous mixtures in accordance with the required properties and in excess of the content of reclaimed asphalt permitted by the technical guidelines. It presents selected bituminous mixtures with the content of RAP of up to 50% and the results of tests from verification of industrial production of those mixtures. The article discusses the details of the design process of mixtures with a high content of reclaimed asphalt, the carried out production tests and discusses the results of tests under the verification of industrial production. Testing included basic tests according to the Polish technical requirements of WT- 2 and the extended functional testing. The conducted tests and analyses helped to determine the usefulness of the developed bituminous mixtures for use in experimental sections and confirmed the possibility of using an increased amount of reclaimed asphalt up to 50% in mixtures intended for construction of national roads.

  2. Grasshopper sparrow reproductive success and habitat use on reclaimed surface mines varies by age of reclamation

    Science.gov (United States)

    Wood, Petra; Ammer, Frank K.

    2015-01-01

    We studied 3 mountaintop mining–valley fill (MTMVF) complexes in southern West Virginia, USA to examine grasshopper sparrow (Ammodramus savannarum pratensis) demographic response to different age classes of mine land reclamation. For 71 nests monitored during the 2001–2002 breeding seasons, overall nest success (36%) was within the range of nest success rates previously reported for this species, but it was highest on more recently reclaimed sites (56%). Nest density and clutch size did not differ (P > 0.30) among reclamation age classes, whereas number of fledglings was greater (P = 0.01) on more recently reclaimed sites. We measured vegetation variables at 70 nest subplots and at 96 systematic subplots to compare nest vegetation with vegetation available on the plots. We found that nests occurred in areas with more bare ground near the nest, greater vegetation height–density surrounding the nest site, lower grass height, and fewer woody stems, similar to previous studies. As postreclamation age increased, vegetation height–density and maximum grass height increased, and sericea (Lespedeza cuneata) became more dominant. Nest success declined with increasing vegetation height–density at the nest. The grasslands available on these reclaimed mine complexes are of sufficient quality to support breeding populations of grasshopper sparrows, but nest success decreased on the older reclaimed areas. Without active management, grasslands on reclaimed MTMVF mines become less suitable for nesting grasshopper sparrows about 10 years after reclamation.

  3. Long-term reclaimed water application effects on phosphorus leaching potential in rapid infiltration basins.

    Science.gov (United States)

    Moura, Daniel R; Silveira, Maria L; O'Connor, George A; Wise, William R

    2011-09-01

    Rapid infiltration basins (RIBs) are effective tools for wastewater treatment and groundwater recharge, but continuous application of wastewater can increase soil P concentrations and subsequently impact groundwater quality. The objectives of this study were to (1) investigate the effects of reclaimed water infiltration rate and "age" of RIBs on soil P concentrations at various depths, and (2) estimate the degree (percentage) of sorption equilibrium reached between effluent P and soil attained during reclaimed water application to different RIBs. The study was conducted in four contrasting cells of a RIB system with up to a 25 year history of secondary wastewater application. Soil samples were collected from 0 to 300 cm depth at 30 cm intervals and analyzed for water extractable phosphorus (WEP) and oxalate extractable P, Al, and Fe concentrations. Water extractable P and P saturation ratio (PSR) values were generally greater in the cells receiving reclaimed water compared to control soils, suggesting that reclaimed water P application can increase soil P concentrations and the risk of P movement to greater depths. Differences between treatment and control samples were more evident in cells with longer histories of reclaimed water application due to greater P loading. Data also indicated considerable spatial variability in WEP concentrations and PSR values, especially within cells from RIBs characterized by fast infiltration rates. This occurs because wastewater-P flows through surface soils much faster than the minimum time required for sorption equilibrium to occur. Studies should be conducted to investigate soil P saturation at deeper depths to assess possible groundwater contamination.

  4. Secondary succession of nematodes in power plant ash dumps reclaimed by covering with turf

    Energy Technology Data Exchange (ETDEWEB)

    Dmowska, E.; Ilieva-Makulec, K. [Polish Academy of Science, Lomianki (Poland)

    2006-11-15

    An analysis of successive changes in nematode assemblages in reclaimed waste area offers information about the sensitivity of species or groups of nematodes to specific conditions and ability to colonise new habitats. The study was carried in ash dumps being a by-product of the combustion of hard coal and reclaimed by covering with mineral turf (light loam warp soil) or organic turf (alder peat). In the first 3 years of reclamation diversity of nematodes was low, especially in, the dump covered with mineral turf - Shannon diversity index below 3. Later on the value of Shannon index increased and did not differ from those recorded for meadows in Poland. In the ash dump, reclaimed for a longer time period (8-11 years), the contribution of K strategist species was higher than in the dumps reclaimed for a shorter time period (2-5 years). At the earlier stages of succession bacterivores Acrobeloides, and two fungivores Aphelenchoides and Aphelenchus, predominated. In the ash dump reclaimed longer the dominance of these three genera decreased and some plant feeders achieved high contribution ({gt} 30%). The composition of nematode communities depended. significantly on the period of reclamation, but did not depend either on the soil moisture and pH or on season.

  5. Effects of waste glass and waste foundry sand additions on reclaimed tiles containing sewage sludge ash.

    Science.gov (United States)

    Lin, Deng-Fong; Luo, Huan-Lin; Lin, Kuo-Liang; Liu, Zhe-Kun

    2017-07-01

    Applying sewage sludge ash (SSA) to produce reclaimed tiles is a promising recycling technology in resolving the increasing sludge wastes from wastewater treatment. However, performance of such reclaimed tiles is inferior to that of original ceramic tiles. Many researchers have therefore tried adding various industrial by-products to improve reclaimed tile properties. In this study, multiple materials including waste glass and waste foundry sand (WFS) were added in an attempt to improve physical and mechanical properties of reclaimed tiles with SSA. Samples with various combinations of clay, WFS, waste glass and SSA were made with three kiln temperatures of 1000°C, 1050°C, and 1100°C. A series of tests on the samples were next conducted. Test results showed that waste glass had positive effects on bending strength, water absorption and weight loss on ignition, while WFS contributed the most in reducing shrinkage, but could decrease the tile bending strength when large amount was added at a high kiln temperature. This study suggested that a combination of WFS from 10% to 15%, waste glass from 15% to 20%, SSA at 10% at a kiln temperature between 1000°C and 1050°C could result in quality reclaimed tiles with a balanced performance.

  6. EBM Irradiation Modification of Palm Oil Biomass Filled Reclaimed Rubber-Mechanical Study

    International Nuclear Information System (INIS)

    Pairu Ibrahim; Ratnam, C.T.

    2016-01-01

    In this project, a study was done to evaluate the mechanical properties of reclaimed rubber filled with palm oil empty fruit bunch (EFB) as fillers. The purpose of filler is to help improve the properties of reclaim rubber and the addition of filler is fixed at 10 parts. Palm oil EFB was obtained from Malaysian Palm Oil Board (MPOB) and prepared at different size. Various samples were prepared with various sizes of filler blended with reclaim rubber using Haake Hot Mixer. The compounds were then compression-moulded at 120 degree Celsius using an electrically heated hydraulic press for their cure times. Dumbbell-shaped tensile and test specimens for hardness and impact test were punched out from the compression-moulded slabs along the mill grain direction. From the test result, it was found that the addition of fillers able to increase the mechanical properties of reclaim rubber and the smaller size of fillers added produced higher tensile properties. The study shows that the palm oil EFB suitable to be used as filler in reclaim rubber. (author)

  7. Biofacies and habitats of Brereton Limestone member (Carbondale Formation, Middle Pennsylvanian), Southwestern Illinois

    Energy Technology Data Exchange (ETDEWEB)

    O' Connell, D.B.; Utgaard, J.

    1983-09-01

    The Brereton Limestone is a shallow-water, open-marine carbonate deposited over peat or delta-plain muds after delta abandonment and a marine transgression. Data on autecology, lithology, insoluble residue content, and thickness were used to interpret the habitats of each biofacies. Biofacies V, a low-diversity biofacies dominated by brachiopods and ostracods, occupied turbid-water, mud- or shelly mud-bottom areas during influxes of detrital clays late in the abandonment of the Herrin delta and, also, early in the construction of the Jamestown delta. Low-relief carbonate mud mounds accumulated within and around baffles provided by thickets of phylloid algae and foraminifers, are capped locally by biofacies VI, a low-diversity biofacies dominated by ostracods. Biofacies VI, occupied the high subtidal to supratidal crests of algal mud mounds which had a stressed (possibly hypersaline) environment. Deeper water mud mounds were occupied by either Biofacies III, a crinoid-mixed fossil biofacies, or by Biofacies IV, which is dominated by fusulinids, strophomenids, and trilobites. Biofacies II, dominated by sponges, mollusks, and impunctate brachiopods, generally occurred on the flanks of the shallow-water mounds. Biofacies I, III, and IV also occurred in broad, muddy intermound areas and Biofacies III in narrow, winnowed intermound areas.

  8. Compressive strength evolution of thermally-stressed Saint Maximin limestone.

    Science.gov (United States)

    Farquharson, J.; Griffiths, L.; Baud, P.; Wadsworth, F. B.; Heap, M. J.

    2017-12-01

    The Saint Maximin quarry (Oise, France) opened in the early 1600s, and its limestone has been used extensively as masonry stone, particularly during the classical era of Parisian architecture from the 17th century onwards. Its widespread use has been due to a combination of its regional availability, its high workability, and its aesthetic appeal. Notable buildings completed using this material include sections of the Place de la Concorde and the Louvre in Paris. More recently, however, it has seen increasing use in the construction of large private residences throughout the United States as well as extensions to private institutions such as Stanford University. For any large building, fire hazard can be a substantial concern, especially in tectonically active areas where catastrophic fires may arise following large-magnitude earthquakes. Typically, house fires burn at temperatures of around 600 °C ( 1000 F). Given the ubiquity of this geomaterial as a building stone, it is important to ascertain the influence of heating on the strength of Saint Maximin limestone (SML), and in turn the structural stability of the buildings it is used in. We performed a series of compressive tests and permeability measurements on samples of SML to determine its strength evolution in response to heating to incrementally higher temperatures. We observe that the uniaxial compressive strength of SML decreases from >12 MPa at room temperature to 400 °C). We anticipate that this substantial weakening is in part a result of thermal microcracking, whereby changes in temperature induce thermal stresses due to a mismatch in thermal expansion between the constituent grains. This mechanism is compounded by the volumetric increase of quartz through its alpha - beta transition at 573 °C, and by the thermal decomposition of calcite. To track the formation of thermal microcracks, we monitor acoustic emissions, a common proxy for microcracking, during the heating of an SML sample. The

  9. Effect of using of reclaimed asphalt and/or lower temperature asphalt on the availability of the road network

    NARCIS (Netherlands)

    Nicholls, C.; Wayman, M.; Mollenhauer, K.; McNally, C.; Tabakovic, A.; Varveri, A.; Cassidy, S.; Shahmohammadi, R.; Taylor, R.

    2015-01-01

    The use of reclaimed asphalt, secondary component materials and/or additives and lower temperature asphalt are being increasingly used in order to improve the sustainability of asphalt production. The use of reclaimed asphalt reduces the need for virgin materials whilst lower temperature asphalts

  10. Influence of reclaimed asphalt with polymer modified bitumen on properties of different asphalts for a wearing course

    NARCIS (Netherlands)

    Komačka, J.; Remišová, E.; Liu, G.; Leegwater, G.; Nielsen, E.

    2014-01-01

    A laboratory investigation was performed to study the effect of reclaimed asphalt with polymer modified bitumen on the properties describing asphalt performance. Three types of asphalts used for wearing courses in Europe (SMA 11, AC 11 and PA 8) were investigated. Five combinations of reclaimed

  11. Oriented nucleation and growth of anhydrite during direct sulfation of limestone

    DEFF Research Database (Denmark)

    Hu, Guilin; Dam-Johansen, Kim; Wedel, Stig

    2008-01-01

    The direct sulfation of limestone (Iceland Spar) was studied at 973 K in a fixed-bed reactor. Scanning electron microscopy examinations of the sulfated limestone particles show that the sulfation process involves oriented nucleation and growth of the solid product, anhydrite. The reason...

  12. Model for the sulfidation of calcined limestone and its use in reactor models.

    NARCIS (Netherlands)

    Heesink, Albertus B.M.; Brilman, Derk Willem Frederik; van Swaaij, Willibrordus Petrus Maria

    1998-01-01

    A mathematical model describing the sulfidation of a single calcined limestone particle was developed and experimentally verified. This model, which includes no fitting parameters, assumes a calcined limestone particle to consist of spherical grains of various sizes that react with H2S according to

  13. Development of engineered cementitious composites with limestone powder and blast furnace slag

    NARCIS (Netherlands)

    Zhou, J.; Qian, S.; Sierra Beltran, M.G.; Ye, G.; Van Breugel, K.; Li, V.C.

    2009-01-01

    Nowadays limestone powder and blast furnace slag (BFS) are widely used in concrete as blended materials in cement. The replacement of Portland cement by limestone powder and BFS can lower the cost and enhance the greenness of concrete, since the production of these two materials needs less energy

  14. LATEST TOURNAISIAN (EARLY CARBONIFEROUS CONODONTS FROM THE TABAI LIMESTONE, TIRAH, NORTHWESTERN PAKISTAN

    Directory of Open Access Journals (Sweden)

    FAZL-I-RABBI KHAN

    2004-11-01

    Full Text Available A new stratigraphic unit, the Tabai Limestone of the poorly known Tirah area of northwest Pakistan, is one of several Early Carboniferous carbonate units distributed along the North Gondwana margin, some connected with transgressive interludes. The Tabai Limestone has produced latest Tournaisian (Early Carboniferous conodonts indicative of the middle of the anchoralis-latus Zone.

  15. High Resolution Hydraulic Profiling and Groundwater Sampling using FLUTe™ System in a Fractured Limestone Setting

    DEFF Research Database (Denmark)

    Janniche, Gry Sander; Christensen, Anders G.; Grosen, Bernt

    challeng-ing in deposit types as fractured limestone. The activities of a bulk distribution facility for perchloroe-thene (PCE) and trichloroethene (TCE) at the Naverland site near Copenhagen, Denmark, has resulted in PCE and TCE DNAPL impacts to a fractured clay till and an underlying fractured limestone...

  16. STEAM ENHANCED REMEDIATION RESEARCH FOR DNAPL IN FRACTURED ROCK, LORING AIR FORCE BASE, LIMESTONE, MAINE

    Science.gov (United States)

    This report details a research project on Steam Enhanced Remediation (SER) for the recovery of volatile organic compounds from fractured limestone that was carried out at the Quarry at the former Loring Air Force Base in Limestone, Maine. This project was carried out by USEPA, Ma...

  17. Holocene limestones of part of the western continental shelf of India

    Digital Repository Service at National Institute of Oceanography (India)

    Nair, R.R.; Hashimi, N.H.; Guptha, M.V.S.

    , while those on te upper continental slope (130-180 m) are algal bryozoan limestones. The limestones have a radiocarbon age ranging between 9,000 and 11,000 years. Depositional environmental on the continental shelf during the Holocene appears...

  18. Evaluation of the Efficiency of Limestone Powder in Concrete and the Effects on the Environment

    Directory of Open Access Journals (Sweden)

    Yoo-Jae Kim

    2018-02-01

    Full Text Available The major environmental impact of concrete comes from the CO2 emissions, produced during the cement manufacturing process. The main goal of this research project is to evaluate the efficiency of limestone powder as a partial cement replacement, in order to reduce energy consumption and CO2 emissions. This study utilizes limestone powders, with different particle sizes, to replace a portion of Portland cement using various ratios. Due to the dilution effect when partially replacing cement, there is a reduction in the concrete’s physical properties. To assess the dilution effect, a modification to Féret’s equation is used to calculate an efficiency factor for the limestone powder when compared to cement. To measure the environmental impact, a life cycle assessment is conducted on concrete made with limestone powder combined with cement. This allows for an evaluation of the various cement/limestone powder ratios that will maximize the environmental benefit, with minimal reduction in concrete strength. Additional microstructural analysis using petrographic examination was completed to provide a visual understanding of the distribution of the limestone particles within the cement paste. The results indicate that the efficiency of limestone powder in partially replacing cement can be achieved by particle packing and particle distribution in the concrete and the benefits of emission reductions exceed the loss in compressive strength when higher levels of limestone powder is used to replace cement.

  19. Semiplanus (Productida, Brachiopoda) from the Carboniferous limestone of Kotaki, Niigata Prefecture, central Japan

    OpenAIRE

    Ibaraki, Yousuke; Sato, Kiichi

    2013-01-01

    An Early Carboniferous large–sized productid brachiopod species, Semiplanus semiplanus (Schwetzow, 1922), is described from the Tsuchikurazawa Limestone (upper Visean–Serpukhovian), a limestone block within a Permian accretionary complex, distributed in the Kotaki area, Itoigawa City, Niigata Prefecture, central Japan. This is the first record of Semipanus species from Japan.

  20. Adsorption and desorption of phosphate on limestone in experiments simulating seawater intrusion

    Science.gov (United States)

    The absorption and desorption of phosphorus on a large block of limestone was investigated using deionized water (DIW) and seawater. The limestone had a high affinity to adsorb phosphorus in DIW. Phosphate adsorption was significantly less in seawater, and more phosphorus was desorbed in the seawate...

  1. Effect of limestone particle size and calcium to non-phytate phosphorus ratio on true ileal calcium digestibility of limestone for broiler chickens.

    Science.gov (United States)

    Anwar, M N; Ravindran, V; Morel, P C H; Ravindran, G; Cowieson, A J

    2016-10-01

    The purpose of this study was to determine the effect of limestone particle size and calcium (Ca) to non-phytate phosphorus (P) ratio on the true ileal Ca digestibility of limestone for broiler chickens. A limestone sample was passed through a set of sieves and separated into fine (digestibility of Ca was calculated using the indicator method and corrected for basal endogenous losses to determine the true Ca digestibility. The basal ileal endogenous Ca losses were determined to be 127 mg/kg of dry matter intake. Increasing Ca:non-phytate P ratios reduced the true Ca digestibility of limestone. The true Ca digestibility coefficients of limestone with Ca:non-phytate P ratios of 1.5, 2.0 and 2.5 were 0.65, 0.57 and 0.49, respectively. Particle size of limestone had a marked effect on the Ca digestibility, with the digestibility being higher in coarse particles (0.71 vs. 0.43).

  2. Limestone fragmentation and attrition during fluidized bed oxyfiring

    Energy Technology Data Exchange (ETDEWEB)

    Fabrizio Scala; Piero Salatino [Istituto di Ricerche sulla Combustione - CNR, Napoli (Italy)

    2010-04-15

    Attrition/fragmentation of limestone under simulated fluidized bed oxyfiring conditions was investigated by means of an experimental protocol that had been previously developed for characterization of attrition/fragmentation of sorbents in air-blown atmospheric fluidized bed combustors. The protocol was based on the use of different and mutually complementary techniques. The extent and pattern of attrition by surface wear in the dense phase of a fluidized bed were assessed in experiments carried out with a bench scale fluidized bed combustor under simulated oxyfiring conditions. Sorbent samples generated during simulated oxyfiring tests were further characterized from the standpoint of fragmentation upon high velocity impact by means of a purposely designed particle impactor. Results showed that under calcination-hindered conditions attrition and fragmentation patterns are much different from those occurring under air-blown atmospheric combustion conditions. Noteworthy, attrition/fragmentation enhanced particle sulfation by continuously regenerating the exposed particle surface. 13 refs., 8 figs.

  3. Sierra Elvira limestone: petrophysical characteristics of an Andalusian heritage stone

    Directory of Open Access Journals (Sweden)

    Valverde, I.

    2008-06-01

    Full Text Available “Sierra Elvira stone” is one of the ornamental building stones most widely used in the historical monuments of eastern Andalusia. A Liassic age limestone, it appears in the central section of the Baetic Mountains and more specifically in the Middle Subbaetic domain. While the most common variety is a crinoid limestone, a micritic limestone of the same age has also been quarried, albeit in much smaller quantities. These stones form very thick beds, up to nearly 5 m deep, that run in consistently parallel lines and have a dip angle that facilitates quarrying.With petrographic, physical and mechanical properties that ensure stone strength and durability, it is a high quality building material suitable for both structural and ornamental purposes. These properties can be attributed to the minimal open porosity and concomitant excellent water resistance that characterize the stone, as well as to its high mechanical strength and low textural anisotropy, both elastic and mechanical. With such attributes, the stone can be successfully used for any number of purposes, including decorative stonework (portals, fountains, plinths, structural members (column shafts and bases or urban curbing and paving. Intervention on Sierra de Elvira limestone structures should be limited to cleaning or repair, for consolidating or protective materials are scantly effective.La “Piedra de Sierra Elvira” constituye una de las piedras ornamentales más significativas del Patrimonio Arquitectónico de Andalucía Oriental. Es una roca caliza del Lias que aflora en el Subbético Medio del sector central de las Cordilleras Béticas. El litotipo más explotado es una caliza con crinoides, en bastante menor importancia se ha extraído también otra caliza micrítica de la misma edad. Los bancos son muy potentes, en algunos casos de más de 5 m, con un paralelismo constante y un buzamiento que favorece su explotación en los frentes de cantera.Sus caracter

  4. Limestone-Concentrate-Pellet Roasting in wet Carbon Dioxide

    Institute of Scientific and Technical Information of China (English)

    1990-01-01

    A roast process for treating chalcopyrite concentrate was developed. The investigation of the reaction of limestone-concentrate-pellet in a wet carbon dioxide flow was carried out by means of a thermogravimetric analysis (TGA) to determine at which temperatures the roasting reaction would take place. The thermodynamic calculations on the roast reaction were made by the use of SOLGASMIX-PV program. The TGA curves and thermodynamic calculations indicated that the conversion of chalcopyrite into bornite took place at about 975K, and the conversion of bornite into chalcocite at 1065-1123K. The thermodynamic calculations also showed that the sulfur released was fixed as calcium sulfide within roasted pellets. X-ray diffraction examination identified these phases in products.

  5. Experienced materials in wet limestone-gypsum FGD system

    Energy Technology Data Exchange (ETDEWEB)

    Hasegawa, S. [Mitsubishi Heavy Industry, Hiroshima (Japan). Hiroshima Research and Development Center; Iwashita, K.; Ochi, E.; Higuchi, T. [Mitsubishi heavy Industry, Yokohama (Japan)

    1998-12-31

    This study was made on the corrosion resistivity evaluation method used for material selection in the Wet Limestone-Gypsum FGD system with examples of various process configuration, their corrosion environment, and the materials used in them. The wet limestone-gypsum process FGD plant is broadly divided into two types-ash-separated (dual-loop) process, and ash-mixed (single-loop) process-depending on whether the flue gas is separated from ash before being led into the absorber or led as it is into the absorber mixed with ash. Presently, the single-loop process has become the mainstream process however. The dual -loop process comprises a dedusting tower (quencher) and an absorption tower (absorber). In the quencher ash is removed with sprayed water where most of the HCl, HF etc., and a part of SO{sub x} and NO{sub x} contained in the flue gas are also removed with absorption. On the contrary, in the single-loop process which is configured of only the absorber, the flue gas is introduced into it as it is contained with ash, SO{sub x}, NO{sub x}, HCl, HF etc. The corrosion environment in these plants largely differs depending on the process type and condition. The absorber recirculated liquid has various ion inclusions among which Cl{sup {minus}} promotes pitting corrosion and crevice corrosion while SO{sub 4}{sup 2{minus}} inhibits these corrosions. Both Cl{sup {minus}} and SO{sub 4}{sup 2{minus}} cover an extremely large range between 25 to 100,000 ppm and 564 to 73,600 ppm respectively, and their influence on the corrosion is related to their activity which is decided by Ca{sup 2+}, Mg{sup 2+}, Na{sup +}, NH{sub 4}{sup +}, H{sup +} and liquid temperature. The balance of these ions is decided by the gas composition, limestone composition, make-up water and wastewater mass balance etc., of individual plants. Accordingly, materials of FGD plant are selected on the basis of evaluated results of corrosion resistivity test made under such simulated process conditions of

  6. SLAM: a sodium-limestone concrete ablation model

    International Nuclear Information System (INIS)

    Suo-Anttila, A.J.

    1983-12-01

    SLAM is a three-region model, containing a pool (sodium and reaction debris) region, a dry (boundary layer and dehydrated concrete) region, and a wet (hydrated concrete) region. The model includes a solution to the mass, momentum, and energy equations in each region. A chemical kinetics model is included to provide heat sources due to chemical reactions between the sodium and the concrete. Both isolated model as well as integrated whole code evaluations have been made with good results. The chemical kinetics and water migration models were evaluated separately, with good results. Several small and large-scale sodium limestone concrete experiments were simulated with reasonable agreement between SLAM and the experimental results. The SLAM code was applied to investigate the effects of mixing, pool temperature, pool depth and fluidization. All these phenomena were found to be of significance in the predicted response of the sodium concrete interaction. Pool fluidization is predicted to be the most important variable in large scale interactions

  7. Geochemistry, environmental and provenance study of the Middle Miocene Leitha limestones (Central Paratethys)

    Science.gov (United States)

    Ali, Ahmed; Wagreich, Michael

    2017-06-01

    Mineralogical, major, minor, REE and trace element analyses of rock samples were performed on Middle Miocene limestones (Leitha limestones, Badenian) collected from four localities from Austria (Mannersdorf, Wöllersdorf, Kummer and Rosenberg quarries) and the Fertőrákos quarry in Hungary. Impure to pure limestones (i.e. limited by Al2O3 contents above or below 0.43 wt. %) were tested to evaluate the applicability of various geochemical proxies and indices in regard to provenance and palaeoenvironmental interpretations. Pure and impure limestones from Mannersdorf and Wöllersdorf (southern Vienna Basin) show signs of detrital input (REEs = 27.6 ± 9.8 ppm, Ce anomaly = 0.95 ± 0.1 and the presence of quartz, muscovite and clay minerals in impure limestones) and diagenetic influence (low contents of, e.g., Sr = 221 ± 49 ppm, Na is not detected, Ba = 15.6 ± 8.8 ppm in pure limestones). Thus, in both limestones the reconstruction of original sedimentary palaeoenvironments by geochemistry is hampered. The Kummer and Fertőrákos (Eisenstadt-Sopron Basin) comprise pure limestones (e.g., averages Sr = 571 ± 139 ppm, Na = 213 ± 56 ppm, Ba = 21 ± 4 ppm, REEs = 16 ± 3 ppm and Ce anomaly = 0.62 ± 0.05 and composed predominantly of calcite) exhibiting negligible diagenesis. Deposition under a shallow-water, well oxygenated to intermittent dysoxic marine environment can be reconstructed. Pure to impure limestones at Rosenberg-Retznei (Styrian Basin) are affected to some extent by detrital input and volcano-siliciclastic admixture. The Leitha limestones at Rosenberg have the least diagenetic influence among the studied localities (i.e. averages Sr = 1271 ± 261 ppm, Na = 315 ± 195 ppm, Ba = 32 ± 15 ppm, REEs = 9.8 ± 4.2 ppm and Ce anomaly = 0.77 ± 0.1 and consist of calcite, minor dolomite and quartz). The siliciclastic sources are characterized by immobile elemental ratios (i.e. La/Sc and Th/Co) which apply not only for the siliciclastics, but also for marls and

  8. Geochemistry, environmental and provenance study of the Middle Miocene Leitha limestones (Central Paratethys

    Directory of Open Access Journals (Sweden)

    Ali Ahmed

    2017-06-01

    Full Text Available Mineralogical, major, minor, REE and trace element analyses of rock samples were performed on Middle Miocene limestones (Leitha limestones, Badenian collected from four localities from Austria (Mannersdorf, Wöllersdorf, Kummer and Rosenberg quarries and the Fertőrákos quarry in Hungary. Impure to pure limestones (i.e. limited by Al2O3 contents above or below 0.43 wt. % were tested to evaluate the applicability of various geochemical proxies and indices in regard to provenance and palaeoenvironmental interpretations. Pure and impure limestones from Mannersdorf and Wöllersdorf (southern Vienna Basin show signs of detrital input (REEs = 27.6 ± 9.8 ppm, Ce anomaly = 0.95 ± 0.1 and the presence of quartz, muscovite and clay minerals in impure limestones and diagenetic influence (low contents of, e.g., Sr = 221 ± 49 ppm, Na is not detected, Ba = 15.6 ± 8.8 ppm in pure limestones. Thus, in both limestones the reconstruction of original sedimentary palaeoenvironments by geochemistry is hampered. The Kummer and Fertőrákos (Eisenstadt–Sopron Basin comprise pure limestones (e.g., averages Sr = 571 ± 139 ppm, Na = 213 ± 56 ppm, Ba = 21 ± 4 ppm, REEs = 16 ± 3 ppm and Ce anomaly = 0.62 ± 0.05 and composed predominantly of calcite exhibiting negligible diagenesis. Deposition under a shallow-water, well oxygenated to intermittent dysoxic marine environment can be reconstructed. Pure to impure limestones at Rosenberg–Retznei (Styrian Basin are affected to some extent by detrital input and volcano-siliciclastic admixture. The Leitha limestones at Rosenberg have the least diagenetic influence among the studied localities (i.e. averages Sr = 1271 ± 261 ppm, Na = 315 ± 195 ppm, Ba = 32 ± 15 ppm, REEs = 9.8 ± 4.2 ppm and Ce anomaly = 0.77 ± 0.1 and consist of calcite, minor dolomite and quartz. The siliciclastic sources are characterized by immobile elemental ratios (i.e. La/Sc and Th/Co which apply not only for the siliciclastics, but also

  9. Electrokinetically Enhanced Delivery for ERD Remediation of Chlorinated Ethenes in a Fractured Limestone Aquifer

    DEFF Research Database (Denmark)

    Broholm, Mette Martina; Hyldegaard, Bente Højlund; With Nedergaard, Lærke

    causing very long remediation timeframes. Electrokinetics (EK) offers some unique transport processes, which can potentially overcome the diffusion limitations in the matrix. A novel technology combines ERD and EK for enhanced delivery. The combined technology (EK-BIO) has shown promising results in clay....... Experimental work on EK-BIO in limestone was conducted in a laboratory setup with limestone cores. EK was demonstrated to be promising in establishing enhanced contact between the donor lactate, bacteria, and cis-DCE within the limestone matrix. Complete dechlorination is expected to take place in the matrix......, since back diffusion limitations in the limestone matrix are overcome. This is essential for the overall time perspective of a remediation in limestone aquifers....

  10. Toxicity of acid mine pit lake water remediated with limestone and phosphorus

    Energy Technology Data Exchange (ETDEWEB)

    Neil, L.L.; McCullough, C.D.; Lund, M.A.; Evans, L.H.; Tsvetnenko, Y. [Edith Cowan University, Joondalup, WA (Australia)

    2009-11-15

    Pit lakes are increasingly common worldwide and have potential to provide many benefits. However, lake water toxicity may require remediation before beneficial end uses can be realised. Three treatments to remediate AMD (pH similar to 4.8) pit lake water containing elevated concentrations of Al and Zn from Collie, Western Australia were tested in mesocosms. Treatments were: (a) limestone neutralisation (L), (b) phosphorus amendment (P), and c) combined limestone neutralisation and phosphorus amendment (L+P). Laboratory bioassays with Ceriodaphnia cf. dubia, Chlorella protothecoides and Tetrahymena thermophila assessed remediation. Limestone neutralisation increased pH and reduced heavy metal concentrations by 98% (Al) to 14% (Mg), removing toxicity to the three test species within 2 months. Phosphorus amendment removed toxicity after 6 months of treatment. However, phosphorus amendment to prior limestone neutralisation failed to reduce toxicity more than limestone neutralisation alone. Low concentrations of both phosphorus and nitrogen appear to limit phytoplankton population growth in all treatments.

  11. Toxicity of acid mine pit lake water remediated with limestone and phosphorus.

    Science.gov (United States)

    Neil, Luke L; McCullough, Clint D; Lund, Mark A; Evans, Louis H; Tsvetnenko, Yuri

    2009-11-01

    Pit lakes are increasingly common worldwide and have potential to provide many benefits. However, lake water toxicity may require remediation before beneficial end uses can be realised. Three treatments to remediate AMD (pH approximately 4.8) pit lake water containing elevated concentrations of Al and Zn from Collie, Western Australia were tested in mesocosms. Treatments were: (a) limestone neutralisation (L), (b) phosphorus amendment (P), and (c) combined limestone neutralisation and phosphorus amendment (L+P). Laboratory bioassays with Ceriodaphnia cf. dubia, Chlorella protothecoides and Tetrahymena thermophila assessed remediation. Limestone neutralisation increased pH and reduced heavy metal concentrations by 98% (Al) to 14% (Mg), removing toxicity to the three test species within 2 months. Phosphorus amendment removed toxicity after 6 months of treatment. However, phosphorus amendment to prior limestone neutralisation failed to reduce toxicity more than limestone neutralisation alone. Low concentrations of both phosphorus and nitrogen appear to limit phytoplankton population growth in all treatments.

  12. Hydration mechanisms of ternary Portland cements containing limestone powder and fly ash

    International Nuclear Information System (INIS)

    De Weerdt, K.; Haha, M. Ben; Le Saout, G.; Kjellsen, K.O.; Justnes, H.; Lothenbach, B.

    2011-01-01

    The effect of minor additions of limestone powder on the properties of fly ash blended cements was investigated in this study using isothermal calorimetry, thermogravimetry (TGA), X-ray diffraction (XRD), scanning electron microscopy (SEM) techniques, and pore solution analysis. The presence of limestone powder led to the formation of hemi- and monocarbonate and to a stabilisation of ettringite compared to the limestone-free cements, where a part of the ettringite converted to monosulphate. Thus, the presence of 5% of limestone led to an increase of the volume of the hydrates, as visible in the increase in chemical shrinkage, and an increase in compressive strength. This effect was amplified for the fly ash/limestone blended cements due to the additional alumina provided by the fly ash reaction.

  13. Residual basins

    International Nuclear Information System (INIS)

    D'Elboux, C.V.; Paiva, I.B.

    1980-01-01

    Exploration for uranium carried out over a major portion of the Rio Grande do Sul Shield has revealed a number of small residual basins developed along glacially eroded channels of pre-Permian age. Mineralization of uranium occurs in two distinct sedimentary units. The lower unit consists of rhythmites overlain by a sequence of black shales, siltstones and coal seams, while the upper one is dominated by sandstones of probable fluvial origin. (Author) [pt

  14. THE POTENTIAL OF RECLAIMED LANDS TO SEQUESTER CARBON AND MITIGATE THE GREENHOUSE EFFECT

    Energy Technology Data Exchange (ETDEWEB)

    Terry Brown; Song Jin

    2006-05-01

    Reclaimed mine lands have the potential to sequester carbon. The use of amendments to increase fertility and overall soil quality is encouraging. Waste amendments such as sewage sludge and clarifier sludge, as well as commercial compost were tested to determine their effects on carbon sequestration and humic acid formation in reclaimed mine lands. Sewage sludge and clarifier sludge have the potential to work as reclaimed mine lands amendments. C:N ratios need to be understood to determine probability of nutrient leaching and water contamination. Microbial activity on the humic acid fraction of sludge is directed toward the readily degradable constituents containing single chain functional groups. This finding indicate that amendments with lower molecular constituents such as aliphatic compounds are more amenable to microbial degradation, therefore serves as better nutrient sources to enhance the formation of vegetation in mine lands and leads to more efficient carbon sequestration.

  15. Penelitian pengaruh penambahan karet reclaim terhadap sifat- sifat kuat tarik, kemuluran dan volume terkikis kompon karet

    Directory of Open Access Journals (Sweden)

    Prayitno Prayitno

    1990-12-01

    Full Text Available Reprocessed of wastevulcanized rubber products, known as reclaim rubber, is used as a filler in rubber soles. Uncorrect usage of reclaim rubber in rubber sole manufacturing can decrease the product performance such as as tensile streangth, elongation break and abrasion resistance. In this experiment, by comparison of 30, 40, 50, 60 and 70 parts of reclaim rubber to the 100 part of natural rubber (RSS sow that tensile strength decreased to 174.138, 160.118, 140.574, 134.092, and 449,60, 437.20, 426.00, 403.80 and 396.60% nrespectively, whereas abrasion resistance decreased to 0,2491, 0,4781, 0,5267, 0.7909, and mm3 / kgm respectively.

  16. Soil arthropod fauna from natural ecosites and reclaimed oil sands soils in northern Alberta

    Energy Technology Data Exchange (ETDEWEB)

    Battigelli, J.P.; Leskiw, L.A. [Paragon Soil and Environmental Consulting Inc., Edmonton, AB (Canada)

    2006-07-01

    An understanding of soil invertebrates may facilitate current reclamation activities in the oil sands region of Alberta. This paper presented the results of a study investigating the density, diversity, and structure of soil arthropod assemblages in natural habitats and reclaimed sites. The purpose of the study was to establish a baseline inventory of soil arthropod assemblages in order to enable long-term monitoring of soil arthropod recolonization in disturbed sites. Nine natural ecosites were sampled for the study, including peat mix over secondary material over tailing sand; direct placement over tailing sand; peat mix over secondary over overburden; direct placement over overburden; peat mix over tailing sand; and peat mix over overburden. Samples were collected from previously established long-term soil and vegetation treatment plots in both natural ecosites and reclaimed soil sites located near Fort McMurray, Alberta. Results showed that densities of mesofauna were significantly higher in samples collected from natural ecosites. Acari and Collembola represented approximately 97 to 98 per cent of the fauna collected. It was also noted that the overall structure of the soil mesofauna community differed between natural soils and reclaimed soils. A significant reduction in the abundance of oribatid mites was observed in soils that had been reclaimed for over 34 years. Changes in the soil mesofauna community structure suggested that reclaimed soils continue to represent disturbed ecosites, as was indicated by higher proportions of prostigmatid mites and some collembolan families. Differences in community structure may influence soil ecosystem functions, including decomposition rates; nutrient recycling; soil structure; and fungal and bacterial biomass. It was concluded that further research is needed to examine oribatid mites and collembolan species diversity and community structure in reclaimed soils. 18 refs., 6 figs.

  17. Safety assessment of greenhouse hydroponic tomatoes irrigated with reclaimed and surface water.

    Science.gov (United States)

    Lopez-Galvez, Francisco; Allende, Ana; Pedrero-Salcedo, Francisco; Alarcon, Juan Jose; Gil, Maria Isabel

    2014-11-17

    The impact of reclaimed and surface water on the microbiological safety of hydroponic tomatoes was assessed. Greenhouse tomatoes were irrigated with reclaimed and surface water and grown on two hydroponic substrates (coconut fiber and rock wool). Water samples (n=208) were taken from irrigation water, with and without the addition of fertilizers and drainage water, and hydroponic tomatoes (n=72). Samples were analyzed for indicator microorganisms, generic Escherichia coli and Listeria spp., and pathogenic bacteria such as Salmonella spp. and Shiga-toxigenic E. coli (STEC), using multiplex real-time PCR (RT-PCR) after enrichment. The correlation between climatological parameters such as temperature and the levels of microorganisms in water samples was also determined. In irrigation water, generic E. coli counts were higher in reclaimed than in surface water whereas Listeria spp. numbers increased after adding the fertilizers in both water sources. In drainage water, no clear differences in E. coli and Listeria numbers were observed between reclaimed and surface water. No positive samples for STEC were found in irrigation water. Presumptive positives for Salmonella spp. were found in 7.7% of the water samples and 62.5% of these samples were reclaimed water. Salmonella-positive samples by RT-PCR could not be confirmed by conventional methods. Higher concentrations of E. coli were associated with Salmonella-presumptive positive samples. Climatological parameters, such as temperature, were not correlated with the E. coli and Listeria spp. counts. Tomato samples were negative for bacterial pathogens, while generic E. coli and Listeria spp. counts were below the detection limit. The prevalence of presumptive Salmonella spp. found in irrigation water (reclaimed and surface water) was high, which might present a risk of contamination. The absence of pathogens on greenhouse hydroponic tomatoes indicates that good agricultural practices (GAP) were in place, avoiding the

  18. 'Religion' and 'body': reclaiming the missing links of Western education

    Directory of Open Access Journals (Sweden)

    Oren Ergas

    2011-01-01

    Full Text Available This paper depicts Western education as being led by a scientific ethos of objectivity. Such an ethos lends itself clearly to a disengagement from ‘religion’ as representing the realm of so-called ‘unscientific knowledge’ and speculation on the one hand, and to a disengagement from the ‘body’ as the locus of sentiment and idiosyncrasy on the other. It is argued, that Western education thus promotes a secular mind-oriented ideology, weeding out the spiritual realm on the one hand, and the emotional-physical realm on the other. It is claimed that education can only take place once it becomes an exploratory path which poses the question ‘who am I?’ at its core. The exploration of such a question will forever be a depleted one as long as it is deprived of ‘religion’ and the ‘body’ as possible research paths. This paper is thus an orientation call for the field of curriculum development serving as a foundation for the ‘holistic education’ discourse developed in recent years. ‘Well-being’ is claimed to be the goal of education. Following this it is showed why this goal cannot be achieved given Western education’s rational (‘body-less’ – secular (‘religion-less’ epistemology. There is thus a need for an attempt to reconceptualize education, which can be made by means of reclaiming the ‘body’ and ‘religion’ as Western education’s missing links, reintegrating them into its proper epistemological/ontological basis. Our inherent dualistic conceptualization of reality (education included should be dealt with, as it constitutes an obstacle to the reconceptualization of education.

  19. Clarification of leachate from reclaimed ground by electron beam irradiation

    International Nuclear Information System (INIS)

    Yamazaki, Masao; Sawai, Teruko; Shimokawa, Toshinari; Sawai, Takeshi

    1985-01-01

    To decompose organic matters such as humic acid and fulvous acid in the leachate from reclaimed ground, an electron beam irradiation technique was examined because of availability of higher dose rate than a 60 Co γ-ray source. This paper describes results of the above-mentioned preliminary examination. Test water was collected from No.15 dumping site at the Tokyo Bay. Irradiation sample was prepared by filtration with a filter and decarbonation with sulfuric acid. Fulvous acid solution by eliminating humic acid was also served for the examination. Electron beam irradiation of the sample solution was made with a Van de Graaf accelerator by 1.5 MeV, 140 Gy/sec of irradiation condition and with a dynamitron by 2.0 MeV, 25 kGy/pass of the condition. It was clarified that oxygen bubbling velocity during the irradiation did not affect much for the decrease rate of total organic matters (TOC) within 0.5 to 3.0 1/min of an experimental condition. As for radiation doses and TOC decrease, TOC was decreased much for lower dose rate irradiation (Van de Graaf accelerator), lower initial TOC concentration, or addition of hydrogen peroxide. For the combined treatment of radiation and flocculation to aim at irradiation dose decrease, fulvous acid solution was served for the test. Lower dose irradiation with a 60 Co source showed better TOC elimination and it was concluded that combination with flocculation was effective for the dose reduction. It was also found experimentally that TOC decrease behavior by the both radiation source was different due to temperature effect and further study should be made for the development of the practical electron beam irradiation technique. (Takagi, S.)

  20. The Scream of the Butterfly: on Reclaiming the Feminine Divine

    Science.gov (United States)

    Marie-Daly, Bernice

    My thesis is that the Feminine Divine has re-entered our age as a primary image for human spiritual growth. Her central energies are immanence, interconnection, mutuality, and interdependence. Emerging from the ancient Goddess tradition, She is reflected anew in contemporary thought in multiple ways. I have explored Her re-emergence in spirituality, psychology, cross-cultural studies, ecofeminism and the new physics. I have focused my research on the experiences of women because women are the original and natural bearers of feminine energies. In the area of spirituality, She expresses Herself through women's reclaiming their sacred image in the women's spirituality movement. Further insights are gained from diverse indigenous cultures which honor the spirit-world in their everyday lives. Ritual, as the enactment of our beliefs, values and world-view, becomes powerful personal and communal expressions of Her re-emergence. From a psychological perspective, I have studied current theories of "Self-in-Relation" and Integrative Psychology. "Self-in-Relation" stresses personal development from within the context of relational growth, both within oneself and with others. Integrative Psychology articulates a body-oriented reconception of feminine and masculine energies. Ecofeminism expresses the confluence of women and nature as intrinsic to meeting environmental demands. Recognizing that treating 'mother' and 'earth' as inexhaustible resources is no longer possible, an ecofeminist position asserts that our assumptions about both women and nature be re -examined. The new physics reconstructs our perception of the universe through quantum physics and chaos theories. These perspectives view the universe as an alive, integrated whole; all aspects, including ourselves, inter-relate with all other aspects. These areas of research demonstrate the emergence of relatedness and interdependence as expressions of a new consciousness which honors the feminine Divine.

  1. ESTABLISHMENT AND EVALUATION OF SWITCHGRASS ON RECLAIMED MINE SOIL [English

    Energy Technology Data Exchange (ETDEWEB)

    Lang, David; Shankle, Brandon; Oswalt, Ernest; Duckworth, Jeremy; Sanborn, Judd; Buell, Rebecca; Roberson, Bill

    2010-06-30

    Switchgrass (Panicum virgatum L.) is a native warm season perennial grass that has productive potential of up to 20 Mg ha-1 of biomass and it persists for decades when harvested once per year. Switchgrass provides excellent ground cover and soil stabilization once established and contributes to soil sequestration of new carbon. Slow establishment on newly reclaimed soil, however, provides for significant erosive opportunities thereby requiring initial soil stabilization with a cover crop. Several planting options were evaluated on two topsoil substitute soils. The planting options included: 1) an existing stand of bermudagrass (Cynodon dactylon L.) that was killed with glyphosate followed by disking in red oxidized topsoil substitute and prime farmland topsoil respread in 2007, 2) red oxidized topsoil substitute was seeded directly with switchgrass, 3) browntop millet (Panicum ramosum) was established with switchgrass, 4) or switchgrass was established in senescing browntop millet or wheat without tillage. Switchgrass was successfully established into a bermudagrass sod that had been killed with herbicides and disked as well as into a senescing stand of browntop millet or wheat. Significant soil erosion occurred on the disked area in 2008 leading to considerable repair work followed by planting wheat. Disked areas that did not erode had an excellent stand of switchgrass with 23.3 plants m-2 in November, 2008. Eroded areas replanted in April, 2009 into senescing wheat had 46 plants m-2 by July, 2009. The area planted directly into newly respread soil in May, 2009 was eroded severely by a 75 mm thunderstorm and was repaired, disked and replanted to switchgrass and browntop millet. Switchgrass seeded with browntop millet had a sparse switchgrass stand and was replanted to switchgrass in August, 2009. Rainfall volumes from August, 2009 to October, 2009 totaled 750 mm, but new erosion damage in areas successfully planted to switchgrass has been minimal.

  2. Radiological characteristic of an area reclaimed by means of an ash-gravel power plant wastes

    International Nuclear Information System (INIS)

    Zak, A.; Biernacka, M.; Kusyk, M.; Mamont-Ciesla, K.; Florowska, K.

    2002-01-01

    A sand excavation after extraction of gravel and sand was filled with an ash-gravel mix. The mix was covered with shielding layers of clay and soil and grass was cultivated on it. Investigations of radiological characteristic such as: gamma radiation dose rate, radon concentration in soil air and radionuclide concentration in the ground were carried out in the both areas reclaimed one and in the vicinity of it. Radon exhalation coefficients were determined for uncovered ash-gravel mix layer, the shielding soil layer and for the ground in the vicinity. Analysis of the results revealed that the reclaimed area can be used for building development. (author)

  3. Water management sustainability in reclaimed coastal areas. The case of the Massaciuccoli lake basin (Tuscany, Italy)

    Science.gov (United States)

    Rossetto, Rudy; Baneschi, Ilaria; Basile, Paolo; Guidi, Massimo; Pistocchi, Chiara; Sabbatini, Tiziana; Silvestri, Nicola; Bonari, Enrico

    2010-05-01

    The lake of Massaciuccoli (7 km2 wide and about 2 m deep) and its palustrine nearby areas (about 13 km2 wide) constitute a residual coastal lacustrine and marshy area largerly drained by 1930. In terms of hydrological boundaries, the lake watershed is bordered by carbonate to arenaceous reliefs on the east, by a sandy coastal shallow aquifer on the west (preventing groundwater salinisation), while south and north by the Serchio River and the Burlamacca-Gora di Stiava channels alignment respectively. Since reclamation of the peaty soils started, subsidence began (2 to 3 m in 70 years), leaving the lake perched and central respect the low drained area, now 0 to -3 m below m.s.l., and requiring 16 km embankment construction. During the dry summer season, the lake undergoes a severe water stress, that, along with nutrients input, causes the continuous ecosystem degradation resulting in water salinisation and eutrophication. Water stress results in a head decrease below m.s.l., causing seawater intrusion along the main outlet, and reaching its highest point at the end of the summer season (common head values between -0.40 and -0.5 a.m.s.l.). The water budget for an average dry season lasting about 100 days was computed, considering a 10% error, in order to understand and evaluate all the components leading to the above mentioned water stress by means of several multidisciplinary activities during the years 2008-2009. They started with a thoroughly literature review, continued with hydrological, hydrogeochemical monitoring and testing (both for surface water and the shallow aquifer) and agronomical investigations (to characterize cropping systems, evapotranspiration rates and irrigation schemes). All the collected data were then processed by means of statistical methods, time series analysis, numerical modelling of the shallow aquifer and hydrological modelling. The results demonstrate the presence of two interrelated hydrological sub-systems: the lake and the reclaimed

  4. Modeling of Hydration, Compressive Strength, and Carbonation of Portland-Limestone Cement (PLC Concrete

    Directory of Open Access Journals (Sweden)

    Xiao-Yong Wang

    2017-01-01

    Full Text Available Limestone is widely used in the construction industry to produce Portland limestone cement (PLC concrete. Systematic evaluations of hydration kinetics, compressive strength development, and carbonation resistance are crucial for the rational use of limestone. This study presents a hydration-based model for evaluating the influences of limestone on the strength and carbonation of concrete. First, the hydration model analyzes the dilution effect and the nucleation effect of limestone during the hydration of cement. The degree of cement hydration is calculated by considering concrete mixing proportions, binder properties, and curing conditions. Second, by using the gel–space ratio, the compressive strength of PLC concrete is evaluated. The interactions among water-to-binder ratio, limestone replacement ratio, and strength development are highlighted. Third, the carbonate material contents and porosity are calculated from the hydration model and are used as input parameters for the carbonation model. By considering concrete microstructures and environmental conditions, the carbon dioxide diffusivity and carbonation depth of PLC concrete are evaluated. The proposed model has been determined to be valid for concrete with various water-to-binder ratios, limestone contents, and curing periods.

  5. Diversity and biogeography of land snails (Mollusca, Gastropoda) in the limestone hills of Perak, Peninsular Malaysia

    Science.gov (United States)

    Foon, Junn Kitt; Clements, Gopalasamy Reuben; Liew, Thor-Seng

    2017-01-01

    Abstract Limestone hills are now gaining global conservation attention as hotspots for short-range endemic species. Levels of land snail endemism can be high at limestone hills, especially at hill clusters that are geographically isolated. In the State of Perak, Peninsular Malaysia, limestone hills have been opportunistically surveyed for land snails in the past, but the majority have yet to be surveyed. To address this knowledge gap, we systematically surveyed the terrestrial malacofauna of 12 limestone hills that, based on our opinion, are a representation of the limestone land snail assemblages within the State. Our inventory yielded high sampling completeness (>85%). We found 122 species of land snails, of which 34 species were unique to one of the surveyed hills. We identified 30 species that are potentially new to science. The number of land snail species recorded at each hill ranged between 39 and 63 species. Four of the sampled limestone hills namely, Prk 01 G. Tempurung, Prk 55 G. Pondok, Prk 47 Kanthan, and Prk 64 Bt Kepala Gajah, have high levels of species richness and unique species, representing 91% of the total species recorded in this study. We identified two clusters of limestone hills in central Perak with distinct differences in land snail species composition – a northern hill cluster on elevated granite bedrock and southern hill cluster in a low-lying valley surrounded by alluvial soils. As limestone hills continue to be quarried to meet the cement demand, the four identified limestone hills, along with other hills from the two clusters, warrant urgent conservation attention in order to maintain high species diversity within Perak’s terrestrial malacofauna. PMID:28769723

  6. 1366 Project Silicon: Reclaiming US Silicon PV Leadership

    Energy Technology Data Exchange (ETDEWEB)

    Lorenz, Adam [1366 Technologies, Bedford, MA (United States)

    2016-02-16

    1366 Technologies’ Project Silicon addresses two of the major goals of the DOE’s PV Manufacturing Initiative Part 2 program: 1) How to reclaim a strong silicon PV manufacturing presence and; 2) How to lower the levelized cost of electricity (“LCOE”) for solar to $0.05-$0.07/kWh, enabling wide-scale U.S. market adoption. To achieve these two goals, US companies must commercialize disruptive, high-value technologies that are capable of rapid scaling, defensible from foreign competition, and suited for US manufacturing. These are the aims of 1366 Technologies Direct Wafer ™ process. The research conducted during Project Silicon led to the first industrial scaling of 1366’s Direct Wafer™ process – an innovative, US-friendly (efficient, low-labor content) manufacturing process that destroys the main cost barrier limiting silicon PV cost-reductions: the 35-year-old grand challenge of making quality wafers (40% of the cost of modules) without the cost and waste of sawing. The SunPath program made it possible for 1366 Technologies to build its demonstration factory, a key and critical step in the Company’s evolution. The demonstration factory allowed 1366 to build every step of the process flow at production size, eliminating potential risk and ensuring the success of the Company’s subsequent scaling for a 1 GW factory to be constructed in Western New York in 2016 and 2017. Moreover, the commercial viability of the Direct Wafer process and its resulting wafers were established as 1366 formed key strategic partnerships, gained entry into the $8B/year multi-Si wafer market, and installed modules featuring Direct Wafer products – the veritable proving grounds for the technology. The program also contributed to the development of three Generation 3 Direct Wafer furnaces. These furnaces are the platform for copying intelligently and preparing our supply chain – large-scale expansion will not require a bigger machine but more machines. SunPath filled the

  7. Capture of SO2 by limestone in a 71 MWe pressurized fluidized bed boiler

    Directory of Open Access Journals (Sweden)

    Shimizu Tadaaki

    2003-01-01

    Full Text Available A 71 MWe pressurized fluidized bed coal combustor was operated. A wide variety of coals were burnt under fly ash recycle conditions. Limestone was fed to the combustor as bed material as well as sorbent. The emission of SO^ and limestone attrition rate were measured. A simple mathematical model of SO? capture by limestone with intermittent solid attrition was applied to the analysis of the present experimental results. Except for high sulfur fuel, the results of the present model agreed with the experimental results.

  8. CARBONIFEROUS CORALS AND CHAETETIDS FROM EXOTIC LIMESTONE BLOCK OF THE CRIMEA

    Directory of Open Access Journals (Sweden)

    VICTOR OGAR

    2015-11-01

    Full Text Available A chaetetid sponge and coral fauna from a Carboniferous exotic limestone block in the Lower Jurassic Esciorda olistostrome on the Bodrak River (Crimean Mountains are described for the first time. The Bodrak exotic block is composed of massive limestone. It contains the chaetetid Chaetetes (Boswellia sp., the tabulate coral Multithecopora sp., and poorly preserved rugose corals, including Dibunophyllum? sp., Cordibia? sp. and gen. et sp. indet. Only the fasciculate colonies of the rugose coral Lytvophyllum askynensis (Kossovaya, 2009 are confidently identified. The studied association of fossils is similar to that of the Donets Basin and the Urals and confirms the Lower Bashkirian age of the Bodrak limestone block. 

  9. Enabling Expeditionary Battlefield Manufacturing Using Recycled, Reclaimed, and/or Indigenous Materials

    Science.gov (United States)

    our operating bases. Indigenous materials include not only the organic and inorganic materials naturally occurring in the area, but could also...include recycled and reclaimed materials from the operating bases (metals, polymers, etc.) as well as battlefield scrap. This idea could potentially reduce

  10. Return on Investment in College Education. The Guardians Initiative: Reclaiming the Public Trust

    Science.gov (United States)

    Association of Governing Boards of Universities and Colleges, 2017

    2017-01-01

    "Return on Investment in College Education" is the second publication in a series of informational briefings developed as part of The Guardians Initiative: Reclaiming the Public Trust, an effort to educate and engage trustees as advocates on key issues in higher education. What is the return on investment (ROI) in college education?…

  11. Selenium geochemistry in reclaimed phosphate mine soils and its relationship with plant bioavailability

    Science.gov (United States)

    Background and Aims Selenium contamination and accumulation in vegetation have resulted in Se toxicity in livestock and wildlife in reclaimed phosphate mine soils in Southeastern Idaho. Methods Plant and soil samples were collected from five study sites near phosphate mines. Soil physiochemical pr...

  12. 30 CFR 77.211 - Draw-off tunnels; stockpiling and reclaiming operations; general.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Draw-off tunnels; stockpiling and reclaiming operations; general. 77.211 Section 77.211 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... WORK AREAS OF UNDERGROUND COAL MINES Surface Installations § 77.211 Draw-off tunnels; stockpiling and...

  13. Raise of efficiency of flocculation-precipitation treatment of exuding water from reclaimed land by irradiation

    International Nuclear Information System (INIS)

    Sawai, Teruko; Yamazaki, Masao; Sawai, Takeshi

    1984-01-01

    When rain falls on the coastal reclaimed land filled with home garbage in Tokyo, a large quantity of water containing much organic contaminant flows out. It is difficult to treat this water exuding from reclaimed land by conventional method. Because the water with low BOD which is difficult to treat by biological process flows out for long period after the stabilization of reclaimed land. When the water is treated by flocculation and precipitation, the substances with high molecular weight are easily removed, but the rate of removal of fulvic acid with low molecular weight, which accounts for more than 60% of the composition of the water, is very poor. Therefore, it was examined to change the fulvic acid to high molecular weight by irradiation, and to improve the efficiency of the flocculation-precipitation treatment of exuding water. Exuding water was sampled in Tokyo Bay No.15 reclaimed land, and it was separated into humic acid and fulvic acid. The Co-60 gamma ray of 5 kCi was irradiated to the samples. The experimental method and the results are reported. The change of fulvic acid to high molecular weight by irradiation was most efficient at pH 2.2. More than 90% of organic contaminants was able to be removed. (Kako, I.)

  14. Reclaimability of the spent sand mixture – sand with bentonite – sand with furfuryl resin

    Directory of Open Access Journals (Sweden)

    J. Dańko

    2011-04-01

    Full Text Available Introduction of new binding materials and new technologies of their hardening in casting moulds and cores production requires theapplication of reclamation methods adequate to their properties as well as special devices realizing tasks. The spent sands circulationsystem containing the same kind of moulding and core sands is optimal from the point of view of the expected reclamation results.However, in the face of a significant variability of applied technologies and related to them various reclamation methods, the need - of theobtained reclamation products assessment on the grounds of systematic criteria and uniform bases – arises, with a tendency of indicatingwhich criteria are the most important for the given sand system. The reclaimability results of the mixture of the spent moulding sand withGeko S bentonite and the spent core sand with the Kaltharz 404U resin hardened by acidic hardener 100 T3, are presented in the paper.Investigations were performed with regard to the estimation of an influence of core sands additions (10 –25% on the reclaimed materialquality. Dusts and clay content in the reclaim, its chemical reaction (pH and ignition loss were estimated. The verification of the reclaiminstrumental assessment was performed on the basis of the technological properties estimation of moulding sand with bentonite, where the reclaimed material was used as a matrix.

  15. Nitrogen and Organics Removal during Riverbank Filtration along a Reclaimed Water Restored River in Beijing, China

    Directory of Open Access Journals (Sweden)

    Weiyan Pan

    2018-04-01

    Full Text Available Reclaimed water has been widely used to restore rivers and lakes in water scarce areas as well as in Beijing municipality, China. However, refilling the rivers with reclaimed water may result in groundwater pollution. A three-year field monitoring program was conducted to assess the effect of a riverbank filtration (RBF system on the removal of nitrogen and organics from the Qingyang River of Beijing, which is replenished with reclaimed water. Water samples from the river, sediment, and groundwater were collected for NO3-N, NH4-N, and chemical oxygen demand (COD was measured. The results indicate that about 85% of NO3-N was removed from the riverbed sediments. Approximate 92% of NH4-N was removed during the infiltration of water from river to aquifer. On average, 54% of COD was removed by RBF. The attenuation of NO3-N through RBF to the groundwater varied among seasons and was strongly related to water temperature. On the other hand, no obvious temporal variability was identified in the removal of COD. These results suggest that the RBF system is an effective barrier against NO3-N, NH4-N and COD in the Qingyang River, as well as those rivers with similar geological and climatic conditions refilled with reclaimed water.

  16. How partial nitrification could improve reclaimed wastewater transport in long pipes.

    Science.gov (United States)

    Delgado, S; Alvarez, M; Rodríguez-Gómez, L E; Elmaleh, S; Aguiar, E

    2001-01-01

    Reclaimed wastewater transport is studied in a concrete-lined cast iron pipe, where a nitrification-denitrification process occurs. The pipe is part of the Reuse System of Reclaimed Wastewater of South Tenerife (Spain), 0.6 m in diameter and 61 km long. In order to improve wastewater quality, at 10 km from the inlet there is injection of fresh water saturated in dissolved oxygen (DO), after which a fast nitrification process usually appears (less than two hours of space time). The amount of oxidized nitrogen compounds produced varies between 0.8 and 4.4 mg/l NOx(-)-N. When DO has disappeared, a denitrification process begins. The removal of nitrite is complete at the end of the pipe, whereas the nitrate does not disappear completely, leaving a concentration of about 0.4-0.5 mg/l. For a COD/NOx(-)-N ratio higher than 5, a first order nitrification rate in NOx(-)-N has resulted, with the constant k20 = 0.079 h-1, for a NOx(-)-N concentration range of 0.8-4.4 mg/l. Finally the following temperature dependency for the first order denitrification rate constant has been found: k = k20 x 1 x 15T-20. Although nitrogen could be used as nutrient in the agricultural reuse, its removal from reclaimed wastewater could be useful in order to diminish the chlorine needs for reclaimed wastewater disinfection.

  17. Development of canopy cover and woody vegetation biomass on reclaimed and unreclaimed post-mining sites

    Czech Academy of Sciences Publication Activity Database

    Frouz, Jan; Dvorščík, P.; Vávrová, A.; Doušová, O.; Kadochová, Štěpánka; Matějíček, L.

    2015-01-01

    Roč. 84, November (2015), s. 233-239 ISSN 0925-8574 Grant - others:GA ČR(CZ) GAP504/12/1288 Program:GA Institutional support: RVO:60077344 Keywords : aerial photographs * reclaimed sites * succession * tree biomass * woody vegetation cover Subject RIV: EH - Ecology, Behaviour Impact factor: 2.740, year: 2015

  18. Pathway for high-quality reclaim by thermal treatment of sulfur-vulcanized SBR

    NARCIS (Netherlands)

    Saiwari, Sitisaiyidah; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.

    2011-01-01

    De-vulcanization of SBR (Styrene Butadiene Rubber) is a challenge, as the broken polymer chains tend to re-arrange. This influences the properties of the reclaimed and re-vulcanized rubber, and reduces the quality of the recycled material. Within this study, the breakdown of sulfur-cured SBR in a

  19. Profile constructing and elevation design of soil reclaimed by hydraulic dredge pump in mining areas

    Energy Technology Data Exchange (ETDEWEB)

    Longqian, C.; Aiqin, S.; Tianjian, Z. [China Univ. of Mining and Technology, Xuzhou, Jiangsu (China). School of Environmental Science and Spatial Informatics; Mei, L. [China Univ. of Mining and Technology, Xuzhou, Jiangsu (China)

    2007-07-01

    Underground coal mining is the main method of coal mining in China. The hydraulic dredge pump reclamation method is the basic method used for repairing hydraulic erosion. This paper reviewed land reclamation by hydraulic dredge pump in the Yi'an coal mine of Xuzhou mining area in the east of China, and analyzed the constructing theory of soil profiling. It examined factors such as the height of the ground-water table; the thickness of plough horizon; the length of crops root and the state of soil erosion; and the methods of profile construction and elevation design of soil reclaimed by hydraulic dredge pump. A relevant mathematical model was also developed. The paper discussed the general situation of the study site as well as the basic theory of profile constructing and the profile constructing method. The paper also discussed the elevation design of the reclaimed land. It was concluded that the practice has proved that the methods can make the reclaimed soil keep a similar characteristics to that of original cropped soil, and meet the requirements for elevation of reclaimed land. 8 refs., 1 tab., 2 figs.

  20. Durability of European Asphalt Mixtures Containing Reclaimed Asphalt and Warm-Mix Additives

    NARCIS (Netherlands)

    Varveri, A.; Avgerinopoulos, S.; Scarpas, Athanasios

    2016-01-01

    This paper investigates the moisture susceptibility of European asphalt mixtures (SMA) containing reclaimed asphalt (RA) and warm mix (WMA) additives. Test sections of a typical SMA mixture have been laid, from which cylindrical samples were cored and utilized for laboratory testing. Four variants

  1. Radon in the Creswell Crags Permian limestone caves

    International Nuclear Information System (INIS)

    Gillmore, G.K.; Phillips, P.S.; Denman, A.R.; Gilbertson, D.D.

    2002-01-01

    An investigation of radon levels in the caves of Creswell Crags, Derbyshire, an important Site of Special Scientific Interest (SSSI) shows that the Lower Magnesian Limestone (Permian) caves have moderate to raised radon gas levels (27-7800 Bq m -3 ) which generally increase with increasing distance into the caves from the entrance regions. This feature is partly explained in terms of cave ventilation and topography. While these levels are generally below the Action Level in the workplace (400 Bq m -3 in the UK), they are above the Action Level for domestic properties (200 Bq m -3 ). Creswell Crags has approximately 40,000 visitors per year and therefore a quantification of effective dose is important for both visitors and guides to the Robin Hood show cave. Due to short exposure times the dose received by visitors is low (0.0016 mSv/visit) and regulations concerning exposure are not contravened. Similarly, the dose received by guides is fairly low (0.4 mSv/annum) due in part to current working practice. However, the risk to researchers entering the more inaccessible areas of the cave system is higher (0.06 mSv/visit). This survey also investigated the effect of seasonal variations on recorded radon concentration. From this work summer to winter ratios of between 1.1 and 9.51 were determined for different locations within the largest cave system

  2. Environmental impact management during construction of the limestone project

    International Nuclear Information System (INIS)

    Windsor, D.C.

    1988-01-01

    The Limestone Generating Station is being constructed on the Nelson River in Northern Manitoba, and will consist of a 10 unit powerhouse, 5 gate concrete spillway and earthfill dam spanning the 1.5 km width of the Nelson River. Environmental concerns associated with the project included insufficient pre- and post-construction monitoring documenting resources present or magnitude of impacts, impacts on brook trout and lake sturgeon resources, wildlife habitat loss due to construction activities, destruction or disturbance of historic or archaeological sites, degradation of nearby water courses and fish habitat by aggregate removal, in-migration of construction personnel, and various other socio-economic impacts. An overview is provided of monitoring activities and results in the above areas, which involved numerous consultants and government agencies. The project administration and workers did not find the environmental programs, including inspection and enforcement activities, to be onerous or an impediment to the project. On the contrary, the environmental requirements assisted in the general planning for certain activities, and in the general criteria for the conduct of the activities. The work permit process was particularly useful as it defined the requirements of both parties and provided the specific standards necessary determining the acceptability of the activities. 14 refs., 1 fig

  3. Transport studies of radon in limestone underlying houses

    International Nuclear Information System (INIS)

    Gammage, R.B.; Dudney, C.S.; Wilson, D.L.; Saultz, R.J.

    1990-01-01

    In hilly limestone terrains of the southern Appalachians, subterranean networks of solution cavities and fissures present circulatory systems facilitating convective and advective transport of radon-bearing gas. Evidence suggests that the primary driving forces for transport are aerostatic pressure differentials created by the difference between the underground and the outside air temperatures. Examples are presented of houses experiencing elevated indoor radon levels as a consequence of communicating with such subsurface transportation systems. The location of a house near the upper or lower end of a subterranean-circulatory system seems to produce amplification of indoor radon levels in winter or summer, respectively. The transport mechanism for radon-bearing air in karst and its impact on indoor radon need better understanding, both in regard to evaluating the geographical prevalence of the phenomenon and the induced spatial and temporal effects that are possible. This paper reports field studies made at houses in karst regions at Oak Ridge, Tennessee, and Huntsville, Alabama. A primary radon-transport mechanism is advocated of ascending or descending subsurface columns of air whose flows are largely driven by aerostatic pressure gradients created by the inground-outdoor air temperature differentials. 5 refs., 5 figs., 1 tab

  4. Interaction and penetration of heated UO2 with limestone concrete

    International Nuclear Information System (INIS)

    Farhadieh, R.; Pedersen, D.R.; Purviance, R.; Carlson, N.

    1982-01-01

    To safeguard the environment against radiological releases, the major question of concern in PAHR safety assessment, following an HCDA, involves confinement and dilution of the molten core-debris. Significant to the study is the directional growth of the core-debris in the concrete foundation of the reactor building or the concrete below the reactor cavity. The real material experiments were carried out in the test apparatus shown. Casts of CRBRP limestone concrete were prepared in graphite cylinders, each having an internal diameter of 8.9 cm and a depth of 30.5 cm. The 17.8-cm-deep concrete samples were allowed to cure for at least 28 days. Experiments were conducted within two months of curing time. The cavity above concrete was packed with 3 kg of pure UO 2 particles (1 to 3 mm). A uranothermic mixture was placed on the top of UO 2 powder. Heating and possible melting of UO 2 was achieved resistively after the ignition of the thermite. Total experimental time was about 60 minutes, during which time a maximum electrical power input of 1.8 watts/gr was applied to the UO 2 . Three gas samples were taken at temperatures of 100, 600, and 950 0 C, measured in the plane of the No. 2 thermocouple. Selection of three temperatures were to study the amount and the type of gases released from different phases of concrete

  5. Microbial quality of reclaimed water for urban reuses: Probabilistic risk-based investigation and recommendations.

    Science.gov (United States)

    Chhipi-Shrestha, Gyan; Hewage, Kasun; Sadiq, Rehan

    2017-01-15

    Although Canada has abundant freshwater resources, many cities still experience seasonal water shortage. Supply-side and demand-side management is a core strategy to address this water shortage. Under this strategy, reclaimed water, which the Canadian public is willing to use for non-potable purposes, is an option. However, no universal guidelines exist for reclaimed water use. Despite the federal government's long-term goal to develop guidelines for many water reuse applications, guidelines have only been prescribed for reclaimed water use in toilet and urinal flushing in Canada. At the provincial level, British Columbia (BC) has promulgated guidelines for wide applications of reclaimed water but only at broad class levels. This research has investigated and proposed probabilistic risk-based recommended values for microbial quality of reclaimed water in various non-potable urban reuses. The health risk was estimated by using quantitative microbial risk assessment. Two-dimensional Monte Carlo simulations were used in the analysis to include variability and uncertainty in input data. The proposed recommended values are based on the indicator organism E. coli. The required treatment levels for reuse were also estimated. In addition, the recommended values were successfully applied to three wastewater treatment effluents in the Okanagan Valley, BC, Canada. The health risks associated with other bacterial pathogens (Campylobacter jejuni and Salmonella spp.), virus (adenovirus, norovirus, and rotavirus), and protozoa (Cryptosporidium parvum and Giardia spp.), were also estimated. The estimated risks indicate the effectiveness of the E. coli-based water quality recommended values. Sensitivity analysis shows the pathogenic E. coli ratio and morbidity are the most sensitive input parameters for all water reuses. The proposed recommended values could be further improved by using national or regional data on water exposures, disease burden per case, and the susceptibility

  6. Aggregate-associated carbon and nitrogen in reclaimed sandy loam soils

    Energy Technology Data Exchange (ETDEWEB)

    Wick, A.F.; Stahl, P.D.; Ingram, L.J. [Virginia Polytechnic Institute & State University, Blacksburg, VA (United States)

    2009-11-15

    Minimal research has been conducted on aggregate, C, and N in coarse-textured soils used to reclaim surface coal mine lands. Furthermore, little is known about the contribution different plant communities make to the recovery of aggregation in these soils. Two chronosequences of semiarid reclaimed sites with sandy loam soils were sampled under shrub- and grass-dominated communities. Aggregation, aggregate fractions, and associated C and N were measured. No definitive trends of increasing macroaggregates between sites were observed undershrubs; however, macro- and microaggregation was greater in the 16-yr-old (0.20 and 0.23 kg aggregate kg{sup -1} soil, respectively) than in the 5-yr-old soils (0.02 and 0.08 kg aggregate kg{sup -1} soil, respectively) under grasses. Although C and N concentrations were drastically reduced (50-75%) with mining activity between the <1-yr-old and native soils, aggregate C and N concentrations tinder shrubs and grasses were similar to each other and to the native soils in the 5-yr-old site. Sods under grass in the 16-yr-old site had lower available and aggregate-occluded C and N concentrations than the 5-yr-old site, while C and N concentrations did not change between 5- and 16-yr-old soils under shrubs. Conversely, aggregate C and N pool sizes under shrubs and grasses both increased with site age to conditions similar to those observed in the native soil. Reclaimed shrub site soils had consistently higher C concentrations in the older reclaimed sites (10 and 16 yr old) than the soils under grasses, indicating greater accumulation and retention of C and N in organic material under shrub than grass communities in semiarid reclaimed sites.

  7. Decision support toolkit for integrated analysis and design of reclaimed water infrastructure.

    Science.gov (United States)

    Lee, Eun Jung; Criddle, Craig S; Geza, Mengistu; Cath, Tzahi Y; Freyberg, David L

    2018-05-01

    Planning of water reuse systems is a complex endeavor. We have developed a software toolkit, IRIPT (Integrated Urban Reclaimed Water Infrastructure Planning Toolkit) that facilitates planning and design of reclaimed water infrastructure for both centralized and hybrid configurations that incorporate satellite treatment plants (STPs). The toolkit includes a Pipeline Designer (PRODOT) that optimizes routing and sizing of pipelines for wastewater capture and reclaimed water distribution, a Selector (SelWTP) that assembles and optimizes wastewater treatment trains, and a Calculator (CalcBenefit) that estimates fees, revenues, and subsidies of alternative designs. For hybrid configurations, a Locator (LocSTP) optimizes siting of STPs and associated wastewater diversions by identifying manhole locations where the flowrates are sufficient to ensure that wastewater extracted and treated at an adjacent STP can generate the revenue needed to pay for treatment and delivery to customers. Practical local constraints are also applied to screen and identify STP locations. Once suitable sites are selected, System Integrator (ToolIntegrator) identifies a set of centralized and hybrid configurations that: (1) maximize reclaimed water supply, (2) maximize reclaimed water supply while also ensuring a financial benefit for the system, and (3) maximize the net financial benefit for the system. The resulting configurations are then evaluated by an Analyst (SANNA) that uses monetary and non-monetary criteria, with weights assigned to appropriate metrics by a decision-maker, to identify a preferred configuration. To illustrate the structure, assumptions, and use of IRIPT, we apply it to a case study for the city of Golden, CO. The criteria weightings provided by a local decision-maker lead to a preference for a centralized configuration in this case. The Golden case study demonstrates that IRIPT can efficiently analyze centralized and hybrid water reuse configurations and rank them

  8. Residual nilpotence and residual solubility of groups

    International Nuclear Information System (INIS)

    Mikhailov, R V

    2005-01-01

    The properties of the residual nilpotence and the residual solubility of groups are studied. The main objects under investigation are the class of residually nilpotent groups such that each central extension of these groups is also residually nilpotent and the class of residually soluble groups such that each Abelian extension of these groups is residually soluble. Various examples of groups not belonging to these classes are constructed by homological methods and methods of the theory of modules over group rings. Several applications of the theory under consideration are presented and problems concerning the residual nilpotence of one-relator groups are considered.

  9. Hydration study of limestone blended cement in the presence of hazardous wastes containing Cr(VI)

    International Nuclear Information System (INIS)

    Trezza, M.A.; Ferraiuelo, M.F.

    2003-01-01

    Considering the increasing use of limestone cement manufacture, the present paper tends to characterize limestone behavior in the presence of Cr(VI). The research reported herein provides information regarding the effect of Cr(VI) from industrial wastes in the limestone cement hydration. The cementitious materials were ordinary Portland cement, as reference, and limestone blended cement. The hydration and physicomechanical properties of cementitious materials and the influence of chromium at an early age were studied with X-ray diffraction (XRD), infrared spectroscopy (FTIR), conductimetric and mechanical tests. Portland cement pastes with the addition of Cr(VI) were examined and leaching behavior with respect to water and acid solution were investigated. This study indicates that Cr(VI) modifies the rate and the components obtained during the cement hydration

  10. Limestones in Treinta y Tres district : Aerial photo of Jose P. Varela - Isla Patrulla

    International Nuclear Information System (INIS)

    Coronel, N.; Heinzen, W.

    1981-01-01

    This work brings information of fields and laboratory samples about the outcrop in Treinta y Tres district in the framework of limestones programme carried out jointly with I.G.U and BGR through the geological German mission

  11. Coated limestone as a filler for the production of PVC-products

    Directory of Open Access Journals (Sweden)

    Mihajlović Slavica

    2005-01-01

    Full Text Available The results of laboratory investigations of the possibility to obtain coated limestone for the production of PVC-products are presented in this paper. Limestone from the "Venčac" deposit (Aranđelovac, Serbia and Montenegro was used as the raw material. The investigations were carried out in two phases: obtaining the coated limestone and determination of the degree of coating. The results of the investigations showed that successful coating of the surface of the limestone particles with Ca-stearate (Ca-stearate content 3% was achieved in a vibro mill with rings and the obtained degree of coating was higher than 95%. The coating degree was determined in transmitted light by a polarization microscope applying the immersion method (water immersion.

  12. Systematic ichnology of microborings from the Cenozoic White Limestone Group, Jamaica, West Indies

    NARCIS (Netherlands)

    Blissett, D.J.; Pickerill, R.K.

    2007-01-01

    The Middle Eocene to Middle Miocene White Limestone Group of Jamaica contains a common and diverse, poorly to well-preserved microboring ichnofauna, namely Centrichnus eccentricus Bromley & Martinell, Curvichnus pediformis isp. nov., Dendrorete balani Tavernier, Campbell & Golubic, Dipatulichnus

  13. Improving DMS 9210 requirements for limestone rock asphalt : year one interim report.

    Science.gov (United States)

    2013-05-01

    Limestone Rock Asphalt (LRA) mixtures have been produced and placed for several decades using specification requirements currently listed under DMS 9210. Several Districts have had placement issues and premature failures at the beginning of 2010. The...

  14. Dolomitization in the diagenetic history of the Štramberg limestones

    Czech Academy of Sciences Publication Activity Database

    Lintnerová, O.; Knietl, M.; Reháková, D.; Skupien, P.; Vašíček, Zdeněk

    2008-01-01

    Roč. 34, 3/1 (2008), s. 191-192 ISSN 0138-0974 Institutional research plan: CEZ:AV0Z30860518 Keywords : Štramberk Limestone * dolomitization * dedolomitization Subject RIV: DB - Geology ; Mineralogy

  15. Deterioration of limestone aggregate mortars by liquid sodium in fast breeder reactor environment

    Energy Technology Data Exchange (ETDEWEB)

    Mohammed Haneefa, K., E-mail: mhkolakkadan@gmail.com [Department of Civil Engineering, IIT Madras, Chennai (India); Santhanam, Manu [Department of Civil Engineering, IIT Madras, Chennai (India); Parida, F.C. [Radiological Safety Division, Indira Gandhi Centre for Atomic Research, Kalpakkam (India)

    2014-08-15

    Highlights: • Limestone mortars were exposed to liquid sodium exposure at 550 °C. • Micro-analytical techniques were used to characterize the exposed specimens. • The performance of limestone mortar was greatly influenced by w/c. • The fundamental degradation mechanisms of limestone mortars were identified. - Abstract: Hot liquid sodium at 550 °C can interact with concrete in the scenario of an accidental spillage of sodium in liquid metal cooled fast breeder reactors. To protect the structural concrete from thermo-chemical degradation, a sacrificial layer of limestone aggregate concrete is provided over it. This study investigates the fundamental mechanisms of thermo-chemical interaction between the hot liquid sodium and limestone mortars at 550 °C for a duration of 30 min in open air. The investigation involves four different types of cement with variation of water-to-cement ratios (w/c) from 0.4 to 0.6. Comprehensive analysis of experimental results reveals that the degree of damage experienced by limestone mortars displayed an upward trend with increase in w/c ratios for a given type of cement. Performance of fly ash based Portland pozzolana cement was superior to other types of cements for a w/c of 0.55. The fundamental degradation mechanisms of limestone mortars during hot liquid sodium interactions include alterations in cement paste phase, formation of sodium compounds from the interaction between solid phases of cement paste and aggregate, modifications of interfacial transition zone (ITZ), decomposition of CaCO{sub 3}, widening and etching of rhombohedral cleavages, and subsequent breaking through the weakest rhombohedral cleavage planes of calcite, staining, ferric oxidation in grain boundaries and disintegration of impurity minerals in limestone.

  16. Deterioration of limestone aggregate mortars by liquid sodium in fast breeder reactor environment

    International Nuclear Information System (INIS)

    Mohammed Haneefa, K.; Santhanam, Manu; Parida, F.C.

    2014-01-01

    Highlights: • Limestone mortars were exposed to liquid sodium exposure at 550 °C. • Micro-analytical techniques were used to characterize the exposed specimens. • The performance of limestone mortar was greatly influenced by w/c. • The fundamental degradation mechanisms of limestone mortars were identified. - Abstract: Hot liquid sodium at 550 °C can interact with concrete in the scenario of an accidental spillage of sodium in liquid metal cooled fast breeder reactors. To protect the structural concrete from thermo-chemical degradation, a sacrificial layer of limestone aggregate concrete is provided over it. This study investigates the fundamental mechanisms of thermo-chemical interaction between the hot liquid sodium and limestone mortars at 550 °C for a duration of 30 min in open air. The investigation involves four different types of cement with variation of water-to-cement ratios (w/c) from 0.4 to 0.6. Comprehensive analysis of experimental results reveals that the degree of damage experienced by limestone mortars displayed an upward trend with increase in w/c ratios for a given type of cement. Performance of fly ash based Portland pozzolana cement was superior to other types of cements for a w/c of 0.55. The fundamental degradation mechanisms of limestone mortars during hot liquid sodium interactions include alterations in cement paste phase, formation of sodium compounds from the interaction between solid phases of cement paste and aggregate, modifications of interfacial transition zone (ITZ), decomposition of CaCO 3 , widening and etching of rhombohedral cleavages, and subsequent breaking through the weakest rhombohedral cleavage planes of calcite, staining, ferric oxidation in grain boundaries and disintegration of impurity minerals in limestone

  17. Resedimented Limestones in Middle and Upper Jurassic Succession of the Slovenian Basin

    Directory of Open Access Journals (Sweden)

    Boštjan Rožič

    2006-12-01

    Full Text Available The Middle and Upper Jurassic succession of the Slovenian Basin is characterized by pelagic sedimentation of siliceous limestones and radiolarian cherts. In the southern and central part of the basin two packages of resedimented limestones are interbedded within pelagic sediments. The Lower resedimented limestones are lower-middle Bajocian to lower Callovian in age. In the southern part of the basin they form laterally discontinuous sequences composed of limestone breccias, calcarenites and micritic limestone and in the central part of the basin calcarenite intercalations within pelagic beds. They were transported by turbidity currents from highly productive ooidal shoals of the Dinaric Carbonate Platform. The Lower resedimented carbonates correlate with the lower three members of the Travnik Formation in the Bovec Trough and similarly developed but much thicker Vajont Formation in the Belluno Basin. The difference in thickness is interpreted as a consequence of shallow-water and longshore currents on the Dinaric Carbonate Platform that transported platform material towards southwest in the direction of the Belluno Basin. The Upper resedimented limestones are upper Kimmeridgian to lower Tithonian and occur within radiolarian cherts in the upper part of the succession as calcarenite beds that originated by turbidity currents. Onset of resedimentation coincides with the emersion-related demise of barrier reef and following deposition of micritic and rare oolitic limestones on the Dinaric Carbonate Platform. Approximatelly coeval resedimented limestones occur in the fourth member of the Travnik Formation in the Bovec Trough, but are not reported from the Ammonitico Rosso Superiore Formation in the Belluno Basin.

  18. Volume change of limestone and its effects on drying shrinkage of concrete

    OpenAIRE

    YAGI, Shogo; AQUINO, Carlos; INOUE, Masumi; OKAMOTO, Takahisa

    2010-01-01

    Recently, the cracks of concrete by drying shrinkage become one of the problems in the construction industry in Japan. The drying shrinkage decreases when the concrete is produced with limestone aggregate. However, it is not clear why the drying shrinkage is decreased. The purpose of this study is to clarify the relation between the drying shrinkage of concrete and the limestone aggregate. In this study, the experiments about the strength, elasticity and drying shrinkage of concrete and the p...

  19. CARBONIFEROUS CORALS AND CHAETETIDS FROM EXOTIC LIMESTONE BLOCK OF THE CRIMEA

    OpenAIRE

    OGAR, VICTOR; KLEVTSOVSKYI, ANDREY

    2015-01-01

    A chaetetid sponge and coral fauna from a Carboniferous exotic limestone block in the Lower Jurassic Esciorda olistostrome on the Bodrak River (Crimean Mountains) are described for the first time. The Bodrak exotic block is composed of massive limestone. It contains the chaetetid Chaetetes (Boswellia) sp., the tabulate coral Multithecopora sp., and poorly preserved rugose corals, including Dibunophyllum? sp., Cordibia? sp. and gen. et sp. indet. Only the fasciculate colonies of the rugose cor...

  20. Enhancement of direct sulfation of limestone by Na{sub 2}CO{sub 3} addition

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Chuanmin [School of Environmental Science and Engineering, North China Electric Power University, Baoding 071003, Hebei Province (China); Zhuang, Ye [Energy and Environmental Research Center, University of North Dakota, 15 North 23rd Street, Grand Forks, ND 58203 (United States); Wang, Chunbo [Department of Power engineering, North China Electric Power University, Baoding 071003, Hebei Province (China)

    2009-07-15

    For an oxy-fuel circulating fluidized bed combustion system, the limestone calcination is normally prevented due to excessive CO{sub 2} partial pressures and the limestone is subject to a direct sulfation reaction. The enhancement of the direct sulfation of limestone by Na{sub 2}CO{sub 3} was investigated under high CO{sub 2} partial pressure in a thermogravimetric apparatus (TGA) and scanning electron microscope (SEM) analysis method. A commercial limestone with a mean size of 18.8 {mu}m was used. Experimental results indicate that the incorporation of Na{sup +} ions in solid product CaSO{sub 4} lattice structures results in formation of more extrinsic point defects in the crystal lattices of CaSO{sub 4} and a significantly increased solid-state diffusivity/mobility in the solid product. So the direct sulfation of Na{sub 2}CO{sub 3}-doped limestone shows higher rate and higher degree of conversion in the later stage of sulfation, in comparison with the direct sulfation of original limestone. The reaction changes from diffusional control to chemical reaction control in the presence of Na{sub 2}CO{sub 3} because of the effect of foreign ions on accelerating the solid-state diffusion. (author)

  1. Enhancement of direct sulfation of limestone by Na{sub 2}CO{sub 3} addition

    Energy Technology Data Exchange (ETDEWEB)

    Chuanmin Chen; Ye Zhuang; Chunbo Wang [North China Electric Power University, Baoding (China). School of Environmental Science & Engineering

    2009-07-15

    For an oxy-fuel circulating fluidized bed combustion system, the limestone calcination is normally prevented due to excessive CO{sub 2} partial pressures and the limestone is subject to a direct sulfation reaction. The enhancement of the direct sulfation of limestone by Na{sub 2}CO{sub 3} was investigated under high CO{sub 2} partial pressure in a thermogravimetric apparatus (TGA) and scanning electron microscope (SEM) analysis method. A commercial limestone with a mean size of 18.8 {mu}m was used. Experimental results indicate that the incorporation of Na{sup +} ions in solid product CaSO{sub 4} lattice structures results in formation of more extrinsic point defects in the crystal lattices of CaSO{sub 4} and a significantly increased solid-state diffusivity/mobility in the solid product. So the direct sulfation of Na{sub 2}CO{sub 3}-doped limestone shows higher rate and higher degree of conversion in the later stage of sulfation, in comparison with the direct sulfation of original limestone. The reaction changes from diffusional control to chemical reaction control in the presence of Na{sub 2}CO{sub 3} because of the effect of foreign ions on accelerating the solid-state diffusion. 33 refs., 7 figs., 2 tabs.

  2. Direct sulfation of limestone based on oxy-fuel combustion technology

    Energy Technology Data Exchange (ETDEWEB)

    Chen, C.M.; Zhao, C.S.; Liu, S.T.; Wang, C.B. [North China Electric Power University, Baoding (China)

    2009-10-15

    With limestone as the sorbent, the sulfation reaction can proceed via two different routes depending on whether calcination of the limestone takes place under the given reaction conditions. The direct sulfation reaction is defined as the sulfation reaction between sulfur dioxide (SO{sub 2}) and limestone in an uncalcined state. This reaction, based on oxyfuel combustion technology, was studied by thermogravimetric analysis. Surface morphologies of the limestone particles after sulfation were examined by a scanning electron microscope. Results show that there are more pores or gaps in the product layer formed by direct sulfation of limestone than by indirect sulfation, which can be attributed to the generation of carbon dioxide (CO{sub 2}) at a reaction interface. Compared with indirect sulfation, direct sulfation of limestone can yield much higher conversion and has a much higher reaction rate. For direct sulfation, the greater porosity in the product layer greatly reduces the solid-state ion diffusion distance, resulting in a higher reaction rate and higher conversion.

  3. Interpretation of well hydrographs in the karstic Maynardville Limestone at the Oak Ridge Y-12 Plant

    International Nuclear Information System (INIS)

    Shevenell, L.A.; McMaster, B.W.

    1996-06-01

    The Maynardville Limestone in Oak Ridge, Tennessee underlies the southern portion of Bear Creek Valley (BCV), and is considered to be the primary pathway for groundwater leaving the Y-12 Plant boundaries. Sixty-seven percent of all wells drilled into the Maynardville Limestone have intersected at least one cavity, suggesting karst features may be encountered throughout the shallow (< 200 ft) portions of the Limestone. Because waste facilities at the Y-12 Plant are located adjacent to the Maynardville Limestone, contaminants could enter the karst aquifer and be transported in the conduit system. As part of an overall hydrologic characterization effort of this karst aquifer, 41 wells in the Maynardville Limestone were instrumented with pressure transducers to monitor water level changes (hydrographs) associated with rain events. Wells at depths between approximately 20 and 750 ft were monitored over the course of at least two storms in order that variations with depth could be identified. The wells selected were not exclusively completed in cavities but were selected to include the broad range of hydrologic conditions present in the Maynardville Limestone. Cavities, fractures and diffuse flow zones were measured at a variety of depths. The water level data from the storms are used to identify areas of quickflow versus slower flowing water zones. The data are also used to estimate specific yields and continuum transmissitives in different portions of the aquifer

  4. Studies on limestone concrete as a low-activation structural material for nuclear power plants

    International Nuclear Information System (INIS)

    Uematsu, Mikio; Nagano, Hiroshi; Naito, Yasuhiro

    2000-01-01

    Because of low content of Li, Co and Eu, the target nuclides of activation reaction, limestone concrete is considered to be effective in reducing the decommissioning cost of nuclear plants. Induced activity calculation and structural strength test were performed for limestone concrete and the results were compared with the data obtained for sandstone concrete, which is generally used in nuclear plants. Minor elements, which are important from the viewpoint of activation, were measured with elementary analysis for limestone samples from three different quarries in Japan. Induced activity in biological shield walls (BSW) of Boiling Water Reactor (BWR) plants was calculated with the isotope generation code ORIGEN-79 using neutron flux data obtained with the one-dimensional Sn transport code ANISN and MGCL 137-group activation cross section library based on JENDL-3. Estimated total radioactivity accumulated in limestone concrete BSW was 5 times lower than that in the sandstone concrete BSW. Structural strength were compared between limestone concrete and sandstone concrete, and limestone concrete was found to have enough compressive strength and tensile strength. (author)

  5. Accelerated weathering of limestone for CO2 mitigation opportunities for the stone and cement industries

    Science.gov (United States)

    Langer, W.H.; Juan, C.A.S.; Rau, G.H.; Caldeira, K.

    2009-01-01

    Large amounts of limestone fines coproduced during the processing of crushed limestone may be useful in the sequestration of carbon dioxide (CO 2). Accelerated weathering of limestone (AWL) is proposed as a low-tech method to capture and sequester CO2 from fossil fuel-fired power plants and other point-sources such as cement manufacturing. AWL reactants are readily available, inexpensive, and environmentally benign. Waste CO 2 is hydrated with water to produce carbonic acid, which then reacts with and is neutralized by limestone fines, thus converting CO2 gas to dissolved calcium bicarbonate. AWL waste products can be disposed of in the ocean. Feasibility requires access to an inexpensive source of limestone and to seawater, thus limiting AWL facilities within about 10 km of the coastline. The majority of U.S. coastal power generating facilities are within economical transport distance of limestone resources. AWL presents opportunities for collaborative efforts among the crushed stone industry, electrical utilities, cement manufactures, and research scientists.

  6. Influence of limestone waste as partial replacement material for sand and marble powder in concrete properties

    Directory of Open Access Journals (Sweden)

    Omar M. Omar

    2012-12-01

    Full Text Available Green concrete are generally composed of recycling materials as hundred or partial percent substitutes for aggregate, cement, and admixture in concrete. Limestone waste is obtained as a by-product during the production of aggregates through the crushing process of rocks in rubble crusher units. Using quarry waste as a substitute of sand in construction materials would resolve the environmental problems caused by the large-scale depletion of the natural sources of river and mining sands. This paper reports the experimental study undertaken to investigate the influence of partial replacement of sand with limestone waste (LSW, with marble powder (M.P as an additive on the concrete properties. The replacement proportion of sand with limestone waste, 25%, 50%, and 75% were practiced in the concrete mixes except in the concrete mix. Besides, proportions of 5%, 10% and 15% marble powder were practiced in the concrete mixes. The effects of limestone waste as fine aggregate on several fresh and hardened properties of the concretes were investigated. The investigation included testing of compressive strength, indirect tensile strength, flexural strength, modulus of elasticity, and permeability. It was found that limestone waste as fine aggregate enhanced the slump test of the fresh concretes. But the unit weight concretes were not affected. However, the good performance was observed when limestone waste as fine aggregate was used in presence of marble powder.

  7. Environmentally acceptable effect of hydrogen peroxide on cave 'lamp-flora', calcite speleothems and limestones

    International Nuclear Information System (INIS)

    Faimon, Jiri; Stelcl, Jindrich; Kubesova, Svatava; Zimak, Jiri

    2003-01-01

    Hydrogen peroxide plus limestone fragments allows removal of organisms without corrosion of limestone and speleothem. - Mosses, algae, and cyanobacteria (lamp-flora) colonize illuminated areas in show caves. This biota is commonly removed by a sodium hypochlorite solution. Because chlorine and other deleterious compounds are released into a cave environment during lamp-flora cleansing, hydrogen peroxide was tested as an alternative agent. In a multidisciplinary study conducted in the Katerinska Cave (Moravian Karst, Czech Republic), 12 algae- and cyanobacteria taxons and 19 moss taxons were detected. The threshold hydrogen peroxide concentration for the destruction of this lamp-flora was found to be 15 vol.%. Based on laboratory experiments in stirred batch reactors, the dissolution rates of limestones and calcite speleothems in water were determined as 3.77x10 -3 and 1.81x10 -3 mol m -2 h -1 , respectively. In the 15% peroxide solution, the limestone and speleothem dissolution rates were one order of magnitude higher, 2.00x10 -2 and 2.21x10 -2 mol m -2 h -1 , respectively. So, the peroxide solution was recognised to attack carbonates somewhat more aggressively than karst water. In order to prevent the potential corrosion of limestone and speleothems, the reaching of preliminary peroxide saturation with respect to calcite is recommended, for example, by adding of few limestone fragments into the solution at least 10 h prior to its application

  8. Mangrove plantation over a limestone reef - Good for the ecology?

    Science.gov (United States)

    Asaeda, Takashi; Barnuevo, Abner; Sanjaya, Kelum; Fortes, Miguel D.; Kanesaka, Yoshikazu; Wolanski, Eric

    2016-05-01

    There have been efforts to restore degraded tropical and subtropical mangrove forests. While there have been many failures, there have been some successes but these were seldom evaluated to test to what level the created mangrove wetlands reproduce the characteristics of the natural ecosystem and thus what ecosystem services they can deliver. We provide such a detailed assessment for the case of Olango and Banacon Islands in the Philippines where the forest was created over a limestone reef where mangroves did not exist in one island but they covered most of the other island before deforestation in the 1940s and 1950s. The created forest appears to have reached a steady state after 60 years. As is typical of mangrove rehabilitation efforts worldwide, planting was limited to a single Rhizophora species. While a forest has been created, it does not mimic a natural forest. There is a large difference between the natural and planted forests in terms of forest structure and species diversity, and tree density. The high density of planted trees excludes importing other species from nearby natural forests; therefore the planted forest remains mono-specific even after several decades and shows no sign of mimicking the characteristics of a natural forest. The planted forests provided mangrove propagules that invaded nearby natural forests. The planted forest has also changed the substratum from sandy to muddy. The outline of the crown of the planted forest has become smooth and horizontal, contrary to that of a natural forest, and this changes the local landscape. Thus we recommend that future mangrove restoration schemes should modify their methodology in order to plant several species, maintain sufficient space between trees for growth, include the naturally dominant species, and create tidal creeks, in order to reproduce in the rehabilitated areas some of the key ecosystem characteristics of natural mangrove forests.

  9. Field Control and Performance of Asphalt Mixtures Containing Greater than 25 Percent Reclaimed Asphalt Pavement : Draft Final Report

    Science.gov (United States)

    2018-02-02

    The Alabama Department of Transportation (ALDOT) and other highway agencies are interested in utilization of higher percentages of reclaimed asphalt pavement (RAP) in asphalt mixtures. There are a number of research studies at both state and national...

  10. The Structure of Reclaiming Warehouse of Minerals at Open-Cut Mines with the Use Combined Transport

    Science.gov (United States)

    Ikonnikov, D. A.; Kovshov, S. V.

    2017-07-01

    In the article performed an analysis of ore reclaiming and overloading point characteristics at modern opencast mines. Ore reclaiming represents the most effective way of stability support of power-intensive and expensive technological dressing process, and, consequently, of maintenance of the optimal production and set-up parameters of extraction and quality of finished product. The paper proposed the construction of the warehouse describing the technology of its creation. Equipment used for the warehouse described in detail. All stages of development and operation was shown. Advantages and disadvantages of using mechanical shovel excavator and hydraulic excavator “backdigger” as a reloading and reclaiming equipment was compared. Ore reclaiming and overloading point construction at cyclical and continuous method of mining using a hydraulic excavator “backdigger” was proposed.

  11. Effects of reclaimed asphalt pavement on indirect tensile strength test of foamed asphalt mix tested in dry condition

    International Nuclear Information System (INIS)

    Katman, Herda Yati; Norhisham, Shuhairy; Ismail, Norlela; Ibrahim, Mohd Rasdan; Matori, Mohd Yazip

    2013-01-01

    Indirect tensile strength (ITS) test was conducted to analyse strength of the foamed asphalt mixes incorporating reclaimed asphalt pavement. Samples were tested for ITS after cured in the oven at 40°C for 72 hours. This testing condition known as dry condition or unconditioned. Laboratory results show that reclaimed asphalt pavement (RAP) contents insignificantly affect the ITS results. ITS results significantly affected by foamed bitumen contents.

  12. Experimental study and mechanism analysis of modified limestone by red mud for improving desulfurization

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Hongtao; Han, Kuihua; Niu, Shengli; Lu, Chunmei; Liu, Mengqi; Li, Hui [Shandong Univ., Jinan (China). School of Energy and Power Engineering

    2013-07-01

    Red mud is a type of solid waste generated during alumina production from bauxite, and how to dispose and utilize red mud in a large scale is yet a question with no satisfied answer. This paper attempts to use red mud as a kind of additive to modify the limestone. The enhancement of the sulfation reaction of limestone by red mud (two kinds of Bayer process red mud and one kind of sintering process red mud) are studied by a tube furnace reactor. The calcination and sulfation process and kinetics are investigated in a thermogravimetric (TG) analyzer. The results show that red mud can effectively improve the desulfurization performance of limestone in the whole temperature range (1,073-1,373K). Sulfur capacity of limestone (means quality of SO{sub 2} which can be retained by 100mg of limestone) can be increased by 25.73, 7.17 and 15.31% while the utilization of calcium can be increased from 39.68 to 64.13%, 60.61 and 61.16% after modified by three kinds of red mud under calcium/metallic element (metallic element described here means all metallic elements which can play a catalytic effect on the sulfation process, including the Na, K, Fe, Ti) ratio being 15, at the temperature of 1,173K. The structure of limestone modified by red mud is interlaced and tridimensional which is conducive to the sulfation reaction. The phase composition analysis measured by XRD of modified limestone sulfated at high temperature shows that there are correspondingly more sulphates for silicate and aluminate complexes of calcium existing in the products. Temperature, calcium/metallic element ratio and particle diameter are important factors as for the sulfation reaction. The optimum results can be obtained as calcium/metallic element ratio being 15. Calcination characteristic of limestone modified by red mud shows a migration to lower temperature direction. The enhancement of sulfation by doping red mud is more pronounced once the product layer has been formed and consequently the promoting

  13. Nomination of the Globigerina Limestone of the Maltese Islands as a "Global Heritage Stone Resource"

    Science.gov (United States)

    Cassar, JoAnn

    2016-04-01

    The Maltese Islands consist of two main islands, Malta and Gozo, as well as a small number of islets, and lie in the central Mediterranean Sea approximately 90 km south of Sicily. Although only 316 square kilometres in size, the Islands contain a rich concentration of archaeological sites and historic buildings, as well as vernacular architecture and modern buildings, for the most part built of the local Globigerina Limestone, which is one of the few natural resources of the Islands. This stone can be described as a typical "soft limestone", very easy to carve and shape. It forms part of the large family of Oligo-Miocene "soft limestones" widely diffused in the Mediterranean Basin. The Maltese Globigerina Limestone Formation is one of five main Formations, and varies in thickness from 20 to over 200 m. The material used for building is located stratigraphically in the lower part of the Globigerina Limestone Formation, called the Lower Globigerina Limestone. This Formation is stratified into thick beds at outcrop. Sections where bioturbation is concentrated often also occur. This limestone is fine-grained, yellow to pale grey in colour, almost wholly composed of the tests of globigerinid planktonic foraminifera. Petrographically, Globigerina Limestone can be described as a bioclastic packstone, with bioclastic wackestones also occurring. This limestone has always been used as the predominant building material in the Islands. The Maltese prehistoric Temples, which were constructed approximately 6000 years ago, bear testimony to this. Between 1530 and 1798 the Order of the Knights of St John built kilometres of fortifications in this same material to protect the Island from the expanding Ottoman Empire. Fortifications, impressive churches, auberges and palaces were built of this stone during this period. The capital city of Valletta, a rich and dense manifestation of Baroque architecture in Globigerina Limestone, is included on the UNESCO World Heritage List, as are

  14. Studies on the preparation of value-added products for limestone

    Energy Technology Data Exchange (ETDEWEB)

    Chae, Young Bae; Jeong, Soo Bok; Ko, Won Sik; Park, Je Shin; Oh, Jung Whan [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

    1997-12-01

    Most of limestone in our country was consumed by the cement and iron/steel making industries and the amount of that was up to 72 million ton in 1996. Recently, importation of high grade limestone that have properties of high whiteness and grade are increased with diversification of chemical products and powder as various qualified filler, because high grade limestone are limited and of few deposit in our country. Therefore, the purpose of this study has investigated to raise to high grade by economical processes with low grade of domestic limestone. In this year, first of all, we investigated the status of application utilize and related industries with the domestic limestone, and then being consideration with condition selected the adequate sample from Andong, Jungsun and Kumsan area. Magnetic materials were involved in impurities of sample, so magnetic separation method was applied in elimination of the ferro-magnetic materials and para-magnetic materials, such as chlorite, muscovite, quartz, dolomite, magnetite, feldspar and so on. The limestone sample has many kinds of impurity. Investigation of flotation was undertaken to eliminate impurities from limestone crude ore and the tests were performed to get a optimum condition adding oleic acid as a promoter, sodium silicate and sodium carbonate as a conditioning agents and MIBC as a frother, while to float the sulfide minerals added amyl xanthate as a promoter, and sulfuric acid as a pH regulator. And most of the impurities involving in flotation sink contained such as quartz, chlorite, muscovite, feldspar, dolomite and so on. Selective crushing and classification methods were performed to eliminate impurities depends on the mineral properties and should be the selective crushing methods are very useful at the manufacturing factory of heavy calcium carbonate with the dry milling system. (author). 36 refs., 46 tabs., 33 figs.

  15. The effects of nutrient enrichment on oil sands reclaimed wetlands : a field microcosm study

    International Nuclear Information System (INIS)

    Chen, H.; Farwell, A.; Dixon, G.

    2010-01-01

    Bitumen extraction processes generate large amounts of processed materials containing polycyclic aromatic hydrocarbons (PAHs), naphthenic acids (NA), and additional salts. The use of processed materials in reclaimed wetlands and lakes has an impact on aquatic faunal and floral colonization. This study investigated the effects on nutrient enrichment on reclaimed wetlands containing processed materials. Chlorophyll a and total biomass analyses were conducted in order to evaluate the influence of nutrient addition on primary production. The nutrients were added to microcosms with differing levels of fertility for 3 different water types with varying NA concentrations in 3 different reclamation substrates. Results of the study showed different levels of growth depending on both the water and substrate type. Combined planktonic and periphytic growth was highest in water with high levels of dissolved organic and inorganic carbon.

  16. Public views of reclaiming an abandoned coal mine: the Macoupin County project

    Energy Technology Data Exchange (ETDEWEB)

    Bernard, J. R.

    1980-07-01

    An abandoned underground coal mine waste area in Macoupin County, Illinois, has been reclaimed for demonstration and research purposes near the city of Staunton. According to federal law, end uses of reclaimed coal mines must be determined in part by local concerns. This study examined local residents' preferences for land uses and their social and economic evaluations of reclamation at the Macoupin County site. Personal interviews with 119 residents revealed preferences for recreational use of the demonstration area; however, responses were probably influenced by prior awareness of land-use intentions. Generally, very positive evaluations of the reclamation were received. Willingness to pay for reclamation appears to be linked to fulfillment of desired recreational uses on the site and socioeconomic status of the respondent. In general, the research results provide further evidence that the value of abatement of environmental damage from mining is recognized and supported in economic terms at the public level.

  17. Reclaiming public space: designing for public interaction with private devices

    DEFF Research Database (Denmark)

    Eriksson, Eva; Hansen, Thomas Riisgaard; Lykke-Olesen, Andreas

    2007-01-01

    . In this paper we explore the implications of interacting in public space and how technology can be rethought to not only act as personal devices, but be the tool to reclaim the right and possibility to interact in public spaces. We introduce information exchange, social support and regulation as three central......Public spaces are changing from being ungoverned places for interaction to be more formalized, controlled, less interactive, and designed places aimed at fulfilling a purpose. Simultaneously, new personal mobile technology aims at providing private individual spaces in the public domain...... aspects for reclaiming public space. The PhotoSwapper application is presented as an example of a system designed to integrate pervasive technology in a public setting. The system is strongly inspired by the activities at a traditional market place. Based on the design of the application we discuss four...

  18. Life Cycle Energy Analysis of Reclaimed Water Reuse Projects in Beijing.

    Science.gov (United States)

    Fan, Yupeng; Guo, Erhui; Zhai, Yuanzheng; Chang, Andrew C; Qiao, Qi; Kang, Peng

    2018-01-01

      To illustrate the benefits of water reuse project, the process-based life cycle analysis (LCA) could be combined with input-output LCA to evaluate the water reuse project. Energy is the only evaluation parameter used in this study. Life cycle assessment of all energy inputs (LCEA) is completed mainly by the life cycle inventory (LCI), taking into account the full life cycle including the construction, the operation, and the demolition phase of the project. Assessment of benefit from water reuse during the life cycle should focus on wastewater discharge reduction and water-saving benefits. The results of LCEA of Beijing water reuse project built in 2014 in a comprehensive way shows that the benefits obtained from the reclaimed water reuse far exceed the life cycle energy consumption. In this paper, the authors apply the LCEA model to estimate the benefits of reclaimed water reuse projects quantitatively.

  19. Recent developments in water quality monitoring for Space Station reclaimed wastewaters

    Science.gov (United States)

    Small, John W.; Verostko, Charles E.; Linton, Arthur T.; Burchett, Ray

    1987-01-01

    This paper discusses the recent developments in water quality monitoring for Space Station reclaimed wastewaters. A preprototype unit that contains an ultraviolet absorbance organic carbon monitor integrated with pH and conductivity sensors is presented. The preprototype has provisions for automated operation and is a reagentless flow-through system without any gas/liquid interfaces. The organic carbon monitor detects by utraviolet absorbance the organic impurities in reclaimed wastewater which may be correlated to the organic carbon content of the water. A comparison of the preprototype organic carbon detection values with actual total organic carbon measurements is presented. The electrolyte double junction concept for the pH sensor and fixed electrodes for both the pH and conductivity sensors are discussed. In addition, the development of a reagentless organic carbon analyzer that incorporates ultraviolet oxidation and infrared detection is presented. Detection sensitivities, hardware development, and operation are included.

  20. Hydrological properties of soils in reclaimed and unreclaimed sites after brown-coal mining

    Czech Academy of Sciences Publication Activity Database

    Cejpek, Jiří; Kuráž, V.; Frouz, J.

    2013-01-01

    Roč. 22, č. 3 (2013), s. 645-652 ISSN 1230-1485 R&D Projects: GA MŠk 2B08023 Grant - others:GAUK(CZ) 169410; GA ČR(CZ) GAP504/12/1288 Program:GA Institutional support: RVO:60077344 Keywords : physical properties * moisture regime * spoil heaps * reclaimed sites * unreclaimed sites Subject RIV: EH - Ecology, Behaviour Impact factor: 0.600, year: 2013

  1. NOx reduction using amine reclaimer wastes (ARW) generated in post combustion CO2 capture

    DEFF Research Database (Denmark)

    Botheju, Deshai; Glarborg, Peter; Tokheim, Lars-Andre

    2012-01-01

    Amine reclaimer wastes (ARW) generated in CO2 capture processes demand suitable disposal means. Such wastes contain remaining amine, NH3 and other degradation compounds. This study investigated the potential of using ARW as a NOx reducing agent, under laboratory conditions in a flow reactor....../NO ratios (waste product, together with its demonstrated NOx reduction capability and its calorific value contribution, makes it attractive as an additive...

  2. A Remote Sensing Approach to Environmental Monitoring in a Reclaimed Mine Area

    Directory of Open Access Journals (Sweden)

    Rajchandar Padmanaban

    2017-12-01

    Full Text Available Mining for resources extraction may lead to geological and associated environmental changes due to ground movements, collision with mining cavities, and deformation of aquifers. Geological changes may continue in a reclaimed mine area, and the deformed aquifers may entail a breakdown of substrates and an increase in ground water tables, which may cause surface area inundation. Consequently, a reclaimed mine area may experience surface area collapse, i.e., subsidence, and degradation of vegetation productivity. Thus, monitoring short-term landscape dynamics in a reclaimed mine area may provide important information on the long-term geological and environmental impacts of mining activities. We studied landscape dynamics in Kirchheller Heide, Germany, which experienced extensive soil movement due to longwall mining without stowing, using Landsat imageries between 2013 and 2016. A Random Forest image classification technique was applied to analyze land-use and landcover dynamics, and the growth of wetland areas was assessed using a Spectral Mixture Analysis (SMA. We also analyzed the changes in vegetation productivity using a Normalized Difference Vegetation Index (NDVI. We observed a 19.9% growth of wetland area within four years, with 87.2% growth in the coverage of two major waterbodies in the reclaimed mine area. NDVI values indicate that the productivity of 66.5% of vegetation of the Kirchheller Heide was degraded due to changes in ground water tables and surface flooding. Our results inform environmental management and mining reclamation authorities about the subsidence spots and priority mitigation areas from land surface and vegetation degradation in Kirchheller Heide.

  3. The reliability evaluation of reclaimed water reused in power plant project

    Science.gov (United States)

    Yang, Jie; Jia, Ru-sheng; Gao, Yu-lan; Wang, Wan-fen; Cao, Peng-qiang

    2017-12-01

    The reuse of reclaimed water has become one of the important measures to solve the shortage of water resources in many cities, But there is no unified way to evaluate the engineering. Concerning this issue, it took Wanneng power plant project in Huai city as a example, analyzed the reliability of wastewater reuse from the aspects of quality in reclaimed water, water quality of sewage plant, the present sewage quantity in the city and forecast of reclaimed water yield, in particular, it was necessary to make a correction to the actual operation flow rate of the sewage plant. the results showed that on the context of the fluctuation of inlet water quality, the outlet water quality of sewage treatment plants is basically stable, and it can meet the requirement of circulating cooling water, but suspended solids(SS) and total hardness in boiler water exceed the limit, and some advanced treatment should be carried out. In addition, the total sewage discharge will reach 13.91×104m3/d and 14.21×104m3/d respectively in the two planning level years of the project. They are greater than the normal collection capacity of the sewage system which is 12.0×104 m3/d, and the reclaimed water yield can reach 10.74×104m3/d, which is greater than the actual needed quantity 8.25×104m3/d of the power plant, so the wastewater reuse of this sewage plant are feasible and reliable to the power plant in view of engineering.

  4. About the use and treatment of reclaimed wastewater; El reto de la reutilizacion de aguas usadas: tratamiento intensivo de aguas residuales

    Energy Technology Data Exchange (ETDEWEB)

    Marin Galvin, R.

    2009-07-01

    Demand of water in our actual society is increasing each day. Taking into account the irregular climatic situation experienced in a lot of zones of Spain, it is necessary to use all the available resources. Among the conventional resources of sweet waters (surface and underground), we must pay attention to the desalted waters and to the reclaimed wastewater. In this way, the practical use of reclaimed wastewater must be supported in three basic items: normative about reusing of reclaimed wastewater, that of treated wastewater and effluents discarded to natural environment and finally, treatment processes to reclaim wastewater. (Author) 11 refs.

  5. Ecological Study in Two Quarried Limestone Karst Hills in Bogor West Java: Vegetation Structure and Floristic Composition

    OpenAIRE

    SATYANTI, ANNISA; CANDRA KUSUMA, YAYAN WAHYU

    2010-01-01

    Many species extinctions have probably gone unnoticed on limestone that was destroyed before they could be sampled. Unless biodiversity surveys are intensified, the true magnitude of extinctions will never be ascertained. The objectives of this study were to determine tree species composition of limestone hills in Nyungcung and Ciampea; to determine quantitatively the dominant and less dominant species and to quantify floristic structure of the two limestone hills. Value of richness (Menhinic...

  6. Effective stress law for the permeability and deformation of four porous limestones

    Science.gov (United States)

    Wang, Y.; Meng, F.; Wang, X.; Baud, P.; Wong, T. F.

    2017-12-01

    The effective stress behavior of a rock is related to the geometric of its pore space. In a microscopically homogeneous assemblage, effective stress coefficients for permeability, volumetric strain and porosity change are predicted to be equal to or less than unity. Experimental measurements are in basic agreement with this prediction, with exceptions particularly in clay-rich sandstones, for which effective stress coefficient for permeability up to 7 was documented. Little is known about carbonates, but Ghabezloo et al. [2009] studied the permeability of an oolitic limestone (from Nimes, France) with 17% porosity and reported effective stress coefficients up to 2.4. We investigated this phenomenon in Indiana, Leitha, Purbeck, and Thala limestones with porosities of 13-30%. Measurements were made at room temperature on water-saturated samples at confining and pore pressures of 7-15 MPa and 1-3 MPa, respectively. Unlike previous studies limited to the permeability, we also determined the effective stress coefficients for volumetric strain and porosity change. Indiana limestone is oolitic, and not surprisingly its behaviour was similar to Nimes limestone, with an effective stress coefficient for permeability of 2.5. Our Indiana limestone data showed that whereas the effective stress coefficient for volumetric strain was 1. Measurements on Purbeck and Thala limestones are consistent with these inequalities, with effective stress coefficients for permeability and porosity change >1 and that for volumetric strain <1. Even though Purbeck and Thala limestones are micritic with appreciable amount of quartz and dolomite, microstructural and mercury porosimetry data showed that their pore spaces are similar to the oolitic limestones, in that the pore size distribution is bimodal with significant fractions of both macropores and micropores. Berryman [1992] analyzed theoretically a rock made up of two porous constituents. Our new data are in agreement with inequalities he

  7. Drenov Grič black limestone as a heritage stone from Slovenia

    Science.gov (United States)

    Kramar, Sabina; Rožič, Boštjan; Žbona, Nina; Bedjanič, Mojca; Mladenović, Ana

    2016-04-01

    The limestone known as Drenov Grič black limestone is considered one of the most beautiful Slovenian natural stones due to its homogenous black colour interwoven with white veins. Over the centuries it has been exploited from three major quarries west of Ljubljana, with the main quarry at Drenov Grič playing the primary role in supplying building material for the central parts of Slovenia. All the quarries are currently not active. In the area of Drenov grič, one locality of black limestone is protected - Kuclerjev kamnolom quarry. It has the status of 'valuable natural feature of national importance' and is protected as a natural monument. This well-stratified micritic limestone of Triassic (Carnian) age occurs in 10-80 cm thick beds, with thin marl interlayers. The stone contains abundant fossil bivalves and ostracods. Apart from calcite as the main component, dolomite, quartz, illite/muscovite and pyrite are also present. The limestone is relatively rich in carbonaceous and bituminous organic matter, which is responsible for the black colour of the stone. This component does not have any adverse effect on mechanical and physical characteristics. As the lime¬stone is dense, thus facilitating a good polish, it has been commercially considered as marble. The stone has been widely used in Slovenian monuments, not only in Ljubljana but also in other regions of Slovenia. Many inner and outdoor architectural elements were made of this limestone, particularly in the baroque period, which was known for the extensive use of black limestones also in other European countries. The most significant use of this limestone has been recorded in sculptured portals and altars. Some of the important buildings decorated utilising this stone, are the Ljubljana Cathedral, the St. James's Parish Church, and the Franciscan Church of the Annunciation, all of which are located in Ljubljana, some of them having been declared as cultural monuments of local or national importance. When

  8. Steam Cured Self-Consolidating Concrete and the Effects of Limestone Filler

    Science.gov (United States)

    Aqel, Mohammad A.

    The purpose of this thesis is to determine the effect and the mechanisms associated with replacing 15% of the cement by limestone filler on the mechanical properties and durability performance of self-consolidating concrete designed and cured for precast/prestressed applications. This study investigates the role of limestone filler on the hydration kinetics, mechanical properties (12 hours to 300 days), microstructural and durability performance (rapid chloride permeability, linear shrinkage, sulfate resistance, freeze-thaw resistance and salt scaling resistance) of various self-consolidating concrete mix designs containing 5% silica fume and steam cured at a maximum holding temperature of 55°C. This research also examines the resistance to delayed ettringite formation when the concrete is steam cured at 70°C and 82°C and its secondary consequences on the freeze-thaw resistance. The effect of several experimental variables related to the concrete mix design and also the curing conditions are examined, namely: limestone filler fineness, limestone filler content, cement type, steam curing duration and steam curing temperature. In general, the results reveal that self-consolidating concrete containing 15% limestone filler, steam cured at 55°C, 70°C and 82°C, exhibited similar or superior mechanical and transport properties as well as long term durability performance compared to similar concrete without limestone filler. When the concrete is steam cured at 55°C, the chemical reactivity of limestone filler has an important role in enhancing the mechanical properties at 16 hours (compared to the concrete without limestone filler) and compensating for the dilution effect at 28 days. Although, at 300 days, the expansion of all concrete mixes are below 0.05%, the corresponding freeze-thaw durability factors vary widely and are controlled by the steam curing temperature and the chemical composition of the cement. Overall, the material properties indicate that the use

  9. Study of biofilm influenced corrosion on cast iron pipes in reclaimed water

    International Nuclear Information System (INIS)

    Zhang, Haiya; Tian, Yimei; Wan, Jianmei; Zhao, Peng

    2015-01-01

    Highlights: • Compared to sterile water, biofilm in reclaimed water promoted corrosion process significantly. • Corrosion rate was accelerated by the biofilm in the first 7 days but was inhibited afterwards. • There was an inverse correlation between the biofilm thickness and general corrosion rate. • Corrosion process was influenced by bacteria, EPS and corrosion products comprehensively. • The corrosion process can be divided into three different stages in our study. - Abstract: Biofilm influenced corrosion on cast iron pipes in reclaimed water was systemically studied using the weight loss method and electrochemical impedance spectroscopy (EIS). The results demonstrated that compared to sterile water, the existence of the biofilm in reclaimed water promoted the corrosion process significantly. The characteristics of biofilm on cast iron coupons were examined by the surface profiler, scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The bacterial counts in the biofilm were determined using the standard plate count method and the most probable number (MPN). The results demonstrated that the corrosion process was influenced by the settled bacteria, EPS, and corrosion products in the biofilm comprehensively. But, the corrosion mechanisms were different with respect to time and could be divided into three stages in our study. Furthermore, several corresponding corrosion mechanisms were proposed for different immersion times.

  10. Study of biofilm influenced corrosion on cast iron pipes in reclaimed water

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Haiya, E-mail: flying850612@126.com; Tian, Yimei, E-mail: ymtian_2000@126.com; Wan, Jianmei, E-mail: 563926510@qq.com; Zhao, Peng, E-mail: zhpeng@tju.edu.cn

    2015-12-01

    Highlights: • Compared to sterile water, biofilm in reclaimed water promoted corrosion process significantly. • Corrosion rate was accelerated by the biofilm in the first 7 days but was inhibited afterwards. • There was an inverse correlation between the biofilm thickness and general corrosion rate. • Corrosion process was influenced by bacteria, EPS and corrosion products comprehensively. • The corrosion process can be divided into three different stages in our study. - Abstract: Biofilm influenced corrosion on cast iron pipes in reclaimed water was systemically studied using the weight loss method and electrochemical impedance spectroscopy (EIS). The results demonstrated that compared to sterile water, the existence of the biofilm in reclaimed water promoted the corrosion process significantly. The characteristics of biofilm on cast iron coupons were examined by the surface profiler, scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The bacterial counts in the biofilm were determined using the standard plate count method and the most probable number (MPN). The results demonstrated that the corrosion process was influenced by the settled bacteria, EPS, and corrosion products in the biofilm comprehensively. But, the corrosion mechanisms were different with respect to time and could be divided into three stages in our study. Furthermore, several corresponding corrosion mechanisms were proposed for different immersion times.

  11. Microbial functional diversity and enzymatic activity of soil degraded by sulphur mining reclaimed with various waste

    Science.gov (United States)

    Joniec, Jolanta; Frąc, Magdalena

    2017-10-01

    The aim of the study was to evaluate microbial functional diversity based on community level physiological profiling and β-glucosidase activity changes in soil degraded by sulphur mining and subjected to reclamation with various waste. The experiment was set up in the area of the former `Jeziórko' Sulphur Mine (Poland), on a soilless substrate with a particle size distribution of slightly loamy sand. The experimental variants included the application of post-flotation lime, sewage sludge and mineral wool. The analyses of soil samples included the assessment of the following microbiological indices: β-glucosidase activity and functional diversity average well color development and richness). The results indicate that sewage sludge did not exert a significant impact on the functional diversity of microorganisms present in the reclaimed soil. In turn, the application of other types of waste contributed to a significant increase in the parameters of total metabolic activity and functional diversity of the reclaimed soil. However, the temporal analysis of the metabolic profile of soil microorganisms demonstrated that a single application of waste did not yield a durable, stable metabolic profile in the reclaimed soil. Still, there was an increase in β-glucosidase activity, especially in objects treated with sewage sludge.

  12. [Study on soil enzyme activities and microbial biomass carbon in greenland irrigated with reclaimed water].

    Science.gov (United States)

    Pan, Neng; Hou, Zhen-An; Chen, Wei-Ping; Jiao, Wen-Tao; Peng, Chi; Liu, Wen

    2012-12-01

    The physicochemical properties of soils might be changed under the long-term reclaimed water irrigation. Its effects on soil biological activities have received great attentions. We collected surface soil samples from urban green spaces and suburban farmlands of Beijing. Soil microbial biomass carbon (SMBC), five types of soil enzyme activities (urease, alkaline phosphatase, invertase, dehydrogenase and catalase) and physicochemical indicators in soils were measured subsequently. SMBC and enzyme activities from green land soils irrigated with reclaimed water were higher than that of control treatments using drinking water, but the difference is not significant in farmland. The SMBC increased by 60.1% and 14.2% than those control treatments in 0-20 cm soil layer of green land and farmland, respectively. Compared with their respective controls, the activities of enzymes in 0-20 cm soil layer of green land and farmland were enhanced by an average of 36.7% and 7.4%, respectively. Investigation of SMBC and enzyme activities decreased with increasing of soil depth. Significantly difference was found between 0-10 cm and 10-20 cm soil layer in green land. Soil biological activities were improved with long-term reclaimed water irrigation in Beijing.

  13. How confident is Fort McKay that industry can reclaim oil sand development

    International Nuclear Information System (INIS)

    Fitzpatrick, C.

    2004-01-01

    This presentation described how traditional environmental knowledge (TEK) can provide valuable information for both the reclamation design and assessment of oil sand development in Fort McKay. Conservation is valued by the Fort McKay First Nations communities who claim that current reclamation methods are too slow, and that the land is not being brought back to its original use with the uniqueness of the boreal landscape. Elders have noted that each year the water level in the Athabasca River is lower. The blowing tailings and coke dust are causing trees to dye and driving animals away. There is concern that the animals that remain may not be safe to eat. The Fort McKay First Nation community has stated that it will view reclamation as a success only when it functions with proof over many generations. The major concerns include: salt in the water draining from reclaimed areas; salt in the soils of reclaimed area; muskeg cannot be recreated; and, the issue of whether cranberry, blueberry and streambank forest areas can be recreated, along with traditional medicinal plants. Other concerns include the loss of rivers such as the Beaver Creek and Tar River, and that the water in reclaimed areas may not be suitable for animals to live in or to drink. tabs., figs

  14. Reclaimed water as an alternative source of water for the city of Bulawayo, Zimbabwe

    Science.gov (United States)

    Taigbenu, Akpofure E.; Ncube, Mthokozisi

    Perennial water problems, precipitated by increased water demand in Bulawayo, the second largest city in Zimbabwe, has prompted the consideration of a wide array of strategies from demand management and water conservation measures to exploitation of alternative water sources. One of such strategies in the latter category includes recycling of blue water for both potable and non-potable purposes. This paper examines the existing reclaimed water system with a view at revamping the existing infrastructure to maximise reclaimed water use for purposes that are amenable to water of lower quality. It is a generally accepted practice to avoid the use of water of high quality for purposes that can tolerate a lower grade, unless it is in excess in amount [ Okun, D.A., 1973. Planning for water reuse. Journal of AWWA 65(10)]. The reclaimed water is assessed in terms of its quality and quantity vis-à-vis possible uses. Perceptions and expectations of both current and identified prospective consumers are examined and discussed, in addition to the feasibility of accommodating these identified prospective consumers in an expanded network. Apart from enhancement of the existing infrastructure, the paper highlights the need for social marketing and education in order to realise the optimum benefits of this alternative water source. The cost implications of implementing the proposed project are evaluated, including suggestions on suitable tariff structure and an allocation distribution that achieves equity.

  15. How confident is Fort McKay that industry can reclaim oil sand development

    Energy Technology Data Exchange (ETDEWEB)

    Fitzpatrick, C. [Fort McKay First Nations, AB (Canada)

    2004-02-05

    This presentation described how traditional environmental knowledge (TEK) can provide valuable information for both the reclamation design and assessment of oil sand development in Fort McKay. Conservation is valued by the Fort McKay First Nations communities who claim that current reclamation methods are too slow, and that the land is not being brought back to its original use with the uniqueness of the boreal landscape. Elders have noted that each year the water level in the Athabasca River is lower. The blowing tailings and coke dust are causing trees to dye and driving animals away. There is concern that the animals that remain may not be safe to eat. The Fort McKay First Nation community has stated that it will view reclamation as a success only when it functions with proof over many generations. The major concerns include: salt in the water draining from reclaimed areas; salt in the soils of reclaimed area; muskeg cannot be recreated; and, the issue of whether cranberry, blueberry and streambank forest areas can be recreated, along with traditional medicinal plants. Other concerns include the loss of rivers such as the Beaver Creek and Tar River, and that the water in reclaimed areas may not be suitable for animals to live in or to drink. tabs., figs.

  16. Evidence for Biogenic Iron in Ediacaran Limestones of the Yenisei Ridge Vorogovka Series (South-Western Framing of the Siberian Craton).

    Science.gov (United States)

    Vinogradov, E.; Kosareva, L.; Metelkin, D. V.; Vishnevskaya, I.

    2017-12-01

    The composition and origin of magnetic minerals are used for reconstructing paleogeography and changes in paleoenvironments. Ediacaran limestones of the Vorogovka Series were studied in the Yenisei Ridge. Rock magnetism of the upper part of the Vorogovka Series completely depends on terrigenous admixture of iron. Non-carbonate residue consists of quartz, plagioclase, muscovite, Fe-Mg chlorite, smectite and pyrite. A prominent positive correlation is observed between the Fe content (1550…9350 ppm) and the amount of insoluble residue. Magnetization of the lower part of Vorogovka Series is due to authigenic iron. There are several indirect indications of the presence of magnetotactic bacteria and seaweed remains in these limestones. While Fe content is high (1200…8330 ppm), Fe-hydroxides, pyrite and other minerals indicating secondary transformations were not detected. Thus, iron was included in the carbonate material during sedimentation. There is no correlation between iron content and the amount of insoluble residue, which indicates that iron could not have been taken from terrigenous admixture. Study of the dependence of magnetic susceptibility from temperature in inert atmosphere (argon) revealed magnetic minerals with demagnetization temperatures of 320°C and 580°C. The former may correspond to greigite (Curie Temperature 307°C) or hexagonal pyrrhotine (325°C). The latter indicates magnetite (Curie Temperature 586°C) which may be authigenic or newly formed during the experiment. Both magnetite and greigite, are major biogenic minerals produced by magnetotactic bacteria. The main environment of modern magnetotactic bacteria is microaerophilic habitat. Therefore, their abundant presence in the Ediacaran sediments is quite natural. All of these are preliminary conclusions until bacteria can be visualized by electron microscopy, which is an ongoing. The work was supported by the Ministry of Education and Science of Russia 5.2324.2017/4.6 and the RFBR 15-05-01428.

  17. Factors involved in the selection of limestone reagents for use in wet FGD systems

    International Nuclear Information System (INIS)

    Jarvis, J.B.; Roothaan, E.S.; Meserole, F.B.; Owens, D.R.

    1992-01-01

    With recent activity in the design and construction of retrofit flue gas desulfurization (FGD) systems, many utilities are faced with the task of selecting limestones which will allow FGD systems to function as designed, and at the same time, provide cost-effective operation. The Electric Power Research Institute (EPRI) has sponsored research to identify factors which should be considered in the reagent selection process. A set of capabilities has been developed which is currently being employed to assist six utilities in selecting cost-effective reagent sources. The major elements in the selection package consist of an analytical characterization of candidate limestones; grindability, reactivity, and magnesium availability testing; and performance modeling utilizing EPRI's FGD PRocess Integration and Simulation Model (FGDPRISM). The results from these measurements are used to perform a site-specific economic analysis which can be used to rank the candidate limestones and quantify the impact of various limestone properties on plant operating costs. This paper includes a description of each element in the selection package along with a review of current research activities aimed at improving predictions of limestone reactivity and magnesium availability. An example is presented which illustrates how reactivity and magnesium availability affect both the performance of an FGD system and plant operating costs

  18. Ruminal degradation of dry matter and neutral detergent fiber of banana peel treated with limestone

    Directory of Open Access Journals (Sweden)

    Flávio Pinto Monção

    2016-02-01

    Full Text Available This study aimed to evaluate the kinetics of dry matter degradation and neutral detergent fiber of banana peel treated with limestone. The banana peel has been acquired from a candy manufacturer that after washing with chlorinated water to 1% and pulp removal was discarded. The banana peel in nature was treated with 1, 2, 3 and 4% of limestone in the natural matter, homogenized and pre-dried in the sun for 120 hours. The experiment was conducted in a completely randomized experimental design, with five treatments (0 (control, 1, 2, 3 and 4% inclusion of limestone with 3 repetitions. The dry matter potential degradability, showed no difference (P>0.05 in the levels compared to the control with an average of 67.58%. The insoluble degradation fraction rate of dry matter and the fiber fraction did not differ (P> 0.05 between levels and control. In relation to effective degradability of neutral detergent fiber, there was an increase of 3.47% for each percentage unit increased limestone. In relation to the ruminal degradation parameters of dry matter and neutral detergent fiber is not recommended the utilization of limestone as an additive in the treatment of banana peel.

  19. Gamma radiation influence on Cladonia substellata (lichen) and its effects on limestone rocks

    International Nuclear Information System (INIS)

    Silva, Helena P. de B.; Colaco, Waldeciro; Pereira, Eugenia C.; Silva, Nicacio H. da

    2009-01-01

    The lichens play an important role in decomposition of the rocky substrate, through the chemical weathering of their substances. This work aimed to determine the influence of gamma Ray on usnic acid production of Cladonia substellata and the influence of chelates formation in limestone rocks. Samples with 2.5 g of C. substellata were packed on paper envelopes for irradiation submission to gamma on a Co-60 source. They received 10 different doses: 5, 7, 10, 15, 20, 30, 40, 50, 60 and 80 Gy. Lichen irradiation was conducted on the gamma irradiator (Co-60), and packed over powdered limestone. Lichen samples were analyzed by High Performance Liquid Chromatography (HPLC) and rocky samples by X-Ray Diffractometry. The X-ray diffractogram obtained from the analysis of limestone not subjected to the action of lichen - control sample was compared with limestone subjected to C. substellata irradiated at doses 10, 30 and 80Gy. Increased production of the usnic acid and changes on the rocky samples were noted. We realized that C. substellata increments the usnic acid biosynthesis as the gamma radiation dose is increased, but there is a limit to it. The chelating effect of the usnic acid on limestone was proportional to the produced amount of the substance, which could be extrapolated to natural conditions, where excessive radiation may influence pedogenesis and ecological succession. (author)

  20. Microfacies and Diagenetic Fabric of the Lockhart Limestone, Kotal Pass Section, Northeast of Kohat, Pakistan

    Directory of Open Access Journals (Sweden)

    Muhammad Waseem Khan

    2016-06-01

    Full Text Available The present study is intended to describe the carbonate microfacies of the Paleocene Lockhart Limestone in area northeast of the Kohat City. The analyzed limestone in the area is 65m thick and predominantly medium to thick bedded, nodular to brecciated and richly fossiliferous. Thin interbeds of marl are observed in the main lithological unit. The lower contact of the Lockhart Limestone is faulted with the Samana Suk Formation of the Jurassic age while conformably overlain by the Patala Formation of Paleocene to Eocene age. The major lithological unit is comprised of predominant assemblage of larger benthic and smaller planktonic foraminifers with accretion of ostracods, dasycladacean algae, echinoderms, gastropods and corals. On the basis of field and laboratory observations, two distinct types of microfacies have been identified as i Dasyclad-Miliolid Foram Wacke-Packstone microfacies of the inner shelf, sub tidal lagoon, ii Larger Foram Packstone microfacies of the middle shelf. The Limestone represents a carbonate cyclic sequence marked by three, transgressive, deepening up cycles representing a gradual sea level rise compensated by vertical accumulation of microfacies. The commencement of each cycle is clearly marked by the input of land-derived siliciclastic sediments and near shore restricted marine faunal/floral assemblage in the inner shelf microfacies gradually thinning up section where the microfacies become deeper offshore. The diagenetic modifications are observed in the shape of compactional framework, dolomitization, aragonite to calcite alteration and spar filled fractures in the main lithological unit of the Lockhart Limestone.

  1. Reclamation of acidic colliery spoil. III. Problems associated with the use of high rates of limestone

    Energy Technology Data Exchange (ETDEWEB)

    Costigan, P A [Univ. of Liverpool, England; Bradshaw, A D; Gemmell, R P

    1982-04-01

    Growth of Trifolium repens in acidic colliery spoil was suppressed by more than 90% when agricultural ground calcitic limestone was applied at above 5 t ha/sup -1/ whereas Lolium perenne was unaffected at rates up to 100 t ha/sup -1/. The inhibitory effect of ground limestone on T. repens was reduced by high phosphorus fertilization and disappeared within 34 weeks of treatment.There was some evidence that high liming caused an imbalance of the Ca/Mg ratio in freshly limed spoil, contribution to growth inhibition. Growth of L. perene was improved and the inhibitory effect on T. repens was alleviated by substituting magnesian limestone (dolomite) for calcitic limestone. Phosphate adsorption of spoil was similar after low and very high limestone applications but increased by 100% after liming at 25 t ha/sup -1/ to pH 5.1.It is suggested that phosphate adsorption at pH 5.1 is caused by freshly precipitated amorphous aluminium hydroxide. The practical implications of the results are discussed.

  2. Actinobacterial diversity in limestone deposit sites in Hundung, Manipur (India and their antimicrobial activities

    Directory of Open Access Journals (Sweden)

    Salam eNimaichand

    2015-05-01

    Full Text Available Studies on actinobacterial diversity in limestone habitats are scarce. This paper reports profiling of actinobacteria isolated from Hundung limestone samples in Manipur, India using ARDRA as the molecular tool for preliminary classification. A total of 137 actinobacteria were clustered into 31 phylotypic groups based on the ARDRA pattern generated and representative of each group was subjected to 16S rRNA gene sequencing. Generic diversity of the limestone isolates consisted of Streptomyces (15 phylotypic groups, Micromonospora (4, Amycolatopsis (3, Arthrobacter (3, Kitasatospora (2, Janibacter (1, Nocardia (1, Pseudonocardia (1 and Rhodococcus (1. Considering the antimicrobial potential of these actinobacteria, 19 showed antimicrobial activities against at least one of the bacterial and candidal test pathogens, while 45 exhibit biocontrol activities against at least one of the rice fungal pathogens. Out of the 137 actinobacterial isolates, 118 were found to have at least one of the three biosynthetic gene clusters (PKS-I, PKS-II, NRPS. The results indicate that 86% of the strains isolated from Hundung limestone deposit sites possessed biosynthetic gene clusters of which 40% exhibited antimicrobial activities. It can, therefore, be concluded that limestone habitat is a promising source for search of novel secondary metabolites.

  3. Impacts of Limestone Multi-particle Size on Production Performance, Egg Shell Quality, and Egg Quality in Laying Hens

    Directory of Open Access Journals (Sweden)

    X. Y. Guo

    2012-06-01

    Full Text Available This experiment was conducted to evaluate the effects of single or multi-particle size limestone on the egg shell quality, egg production, egg quality and feed intake in laying hens. A total of 280 laying hens (ISA brown were used in this 10-wk trial. Laying hens were randomly assigned to 4 treatments with 14 replications per treatment and 5 adjacent cages as a replication (hens were caged individually. The experimental treatments were: i L, basal diet+10% large particle limestone; ii LS1, basal diet+8% large particle limestone+2% small particle limestone; iii LS2, basal diet+6% large particle limestone+4% small particle limestone; iv S, basal diet+10% small particle limestone. The egg production was unaffected by dietary treatments. The egg weight in S treatment was lighter than other treatments (p<0.05. The egg specific gravity in S treatment was lower than other treatments (p<0.05. The eggshell strength and eggshell thickness in S treatment were decreased when compared with other dietary treatments (p<0.05. The laying hens in LS1 and LS2 treatment had a higher average feed intake than the other two treatments (p<0.05. Collectively, the dietary multi-particle size limestone supplementation could be as efficient as large particle size limestone.

  4. Porosity development in the Copper Ridge Dolomite and Maynardville Limestone, Bear Creek Valley and Chestnut Ridge, Tennessee

    International Nuclear Information System (INIS)

    Goldstrand, P.M.; Menefee, L.S.; Dreier, R.B.

    1995-12-01

    Matrix porosity data from deep core obtained in Bear Creek Valley indicate that porosities in the Maynardville Limestone are lithology and depth dependent. Matrix porosities are greater in the Cooper Ridge Dolomite than in the Maynardville Limestone, yet there is no apparent correlation with depth. Two interrelated diagenetic processes are the major controlling factors on porosity development in the Copper Ridge Dolomite and Maynardville Limestone; dissolution of evaporate minerals and dedolomitization. Both of these diagenetic processes produce matrix porosities between 2.1 and 1.3% in the Copper Ridge Dolomite and upper part of the Maynardville Limestone (Zone 6) to depths of approximately 600 ft bgs. Mean matrix porosities in Zones 5 through 2 of the Maynardville Limestone range from 0.8 to 0.5%. A large number of cavities have been intersected during drilling activities in nearly all zones of the Maynardville Limestone in Bear Creek Valley. Therefore, any maynardville Limestone zone within approximately 200 ft of the ground surface is likely to contain cavities that allow significant and rapid flow of groundwater. Zone 6 could be an important stratigraphic unit in the Maynardville Limestone for groundwater flow and contaminant transport because of the abundance of vuggy and moldic porosities. There are large variations in the thickness and lithology in the lower part of the Maynardville (Zones 2, 3, and 4 in the Burial Grounds region). The direction and velocity of strike-parallel groundwater flow may be altered in this area within the lower Maynardville Limestone

  5. Fine and Coarse-Scale Patterns of Vegetation Diversity on Reclaimed Surface Mine-land Over a 40-Year Chronosequence.

    Science.gov (United States)

    Bohrer, Stefanie L; Limb, Ryan F; Daigh, Aaron L; Volk, Jay M; Wick, Abbey F

    2017-03-01

    Rangelands are described as heterogeneous, due to patterning in species assemblages and productivity that arise from species dispersal and interactions with environmental gradients and disturbances across multiple scales. The objectives of rangeland reclamation are typically vegetation establishment, plant community productivity, and soil stability. However, while fine-scale diversity is often promoted through species-rich seed mixes, landscape heterogeneity and coarse-scale diversity are largely overlooked. Our objectives were to evaluate fine and coarse-scale vegetation patterns across a 40-year reclamation chronosequence on reclaimed surface coalmine lands. We hypothesized that both α-diversity and β-diversity would increase and community patch size and species dissimilarity to reference sites would decrease on independent sites over 40 years. Plant communities were surveyed on 19 post-coalmine reclaimed sites and four intact native reference sites in central North Dakota mixed-grass prairie. Our results showed no differences in α or β-diversity and plant community patch size over the 40-year chronosequence. However, both α-diversity and β-diversity on reclaimed sites was similar to reference sites. Native species establishment was limited due to the presence of non-native species such as Kentucky bluegrass (Poa pratensis) on both the reclaimed and reference sites. Species composition was different between reclaimed and reference sites and community dissimilarity increased on reclaimed sites over the 40-year chronosequence. Plant communities resulting from reclamation followed non-equilibrium succession, even with consistent seeds mixes established across all reclaimed years. This suggests post-reclamation management strategies influence species composition outcomes and land management strategies applied uniformly may not increase landscape-level diversity.

  6. Properies of binder systems containing cement, fly ash, and limestone powder

    Directory of Open Access Journals (Sweden)

    Krittiya Kaewmanee

    2014-10-01

    Full Text Available Fly ash and limestone powder are two major widely available cement replacing materials in Thailand. However, the current utilization of these materials is still not optimized due to limited information on properties of multi-binder systems. This paper reports on the mechanical and durability properties of mixtures containing cement, fly ash, and limestone powder as single, binary, and ternary binder systems. The results showed that a single binder system consisting of only cement gave the best carbonation resistance. A binary binder system with fly ash exhibited superior performances in long-term compressive strength and many durability properties except carbonation and magnesium sulfate resistances, while early compressive strength of a binary binder system with limestone powder was excellent. The ternary binder system, taking the most benefit of selective cement replacing materials, yielded, though not the best, satisfactory performances in almost all properties. Thus, the optimization of binders can be achieved through a multi-binder system.

  7. A correlation of Sr isotope stratigraphy and foraminiferal biostratigraphy in tertiary limestones of Papua New Guinea

    International Nuclear Information System (INIS)

    Allan, T.L.; Trotter, J.A.; Whitford, D.J.; Korsch, M.J.

    2000-01-01

    Strontium isotopic and stratigraphic data collected from the Darai Limestone of Papua New Guinea clearly demonstrate a systematic relationship between bulk 87 Sr/ 86 Sr ratio and index foraminiferal composition that closely reflects the relative stratigraphical range of the foraminifera in this region. A graphic correlation of stratigraphic, strontium isotopic and age ranges of the major index taxa permits direct evaluation of limestone age and isotopic composition in the Darai Limestone. The age of the Tf 1 /Tf 2 boundary (∼12.2 Ma) is significantly younger than the accepted estimate of ∼15.0 Ma (plankton Zone N9) and the Te/Tf boundary (∼20.3 Ma) is older than the generally accepted age of ∼l 8.5 Ma (plankton Zone N6)

  8. A NEW DAONELLA FROM THE LADINIAN PLATFORM OF THE ESINO LIMESTONE (SOUTHERN ALPS, ITALY

    Directory of Open Access Journals (Sweden)

    CRISTIANO LARGHI

    2006-03-01

    Full Text Available The bivalve Daonella Mojsisovics, 1874 is very common in the Middle Triassic pelagic facies, whereas the record of this genus from shallow water limestones is rare. In the present paper a new species of Daonella, named D. pseudograbensis, is described from the Esino Limestone, a Ladinian (Middle Triassic carbonate platform in the central Southern Alps. The species is described from Brembana Valley, where the Esino Limestone is rather rich in bioclastic lenses yielding faunas with bivalves, cephalopods, gastropods, brachiopods, corals and calcareous algae. Daonella pseudograbensis n. sp. is based on very well preserved specimens, which are often articulated and closed, all coming from the same locality. The new species shows a narrow range of intraspecific and ontogenetic morphologic variations. It is easy distinguishable from the other species of the genus for the outline and ornamentation; it therefore differs from D. grabensis Kittl, 1912, the most similar species, for the longer anterior dorsal margin.Pdf

  9. Successful experience with limestone and other sorbents for combustion of biomass in fluid bed power boilers

    Energy Technology Data Exchange (ETDEWEB)

    Coe, D.R. [LG& E Power Systems, Inc., Irvine, CA (United States)

    1993-12-31

    This paper presents the theoretical and practical advantages of utilizing limestone and other sorbents during the combustion of various biomass fuels for the reduction of corrosion and erosion of boiler fireside tubing and refractory. Successful experiences using a small amount of limestone, dolomite, kaolin, or custom blends of aluminum and magnesium compounds in fluid bed boilers fired with biomass fuels will be discussed. Electric power boiler firing experience includes bubbling bed boilers as well as circulating fluid bed boilers in commercial service on biomass fuels. Forest sources of biomass fuels fired include wood chips, brush chips, sawmill waste wood, bark, and hog fuel. Agricultural sources of biomass fuels fired include grape vine prunings, bean straw, almond tree chips, walnut tree chips, and a variety of other agricultural waste fuels. Additionally, some urban sources of wood fuels have been commercially burned with the addition of limestone. Data presented includes qualitative and quantitative analyses of fuel, sorbent, and ash.

  10. Modelling of catalytic oxidation of NH3 and reduction of NO on limestone during sulphur capture

    DEFF Research Database (Denmark)

    Kiil, Søren; Bhatia, Suresh K.; Dam-Johansen, Kim

    1996-01-01

    activity with respect to each species involved. An existing particle model, the Grain-Micrograin Model, which simulates sulphur capture on limestone under oxidizing conditions is considered in the modelling. Simulation results in good qualitative agreement with experimental data are obtained here......A theoretical study of the complex transient system of simultaneous sulphur capture and catalytic reactions of N-containing compounds taking place on a single limestone particle is conducted. The numerical technique developed previously by the authors (Kiil et al. 1994) based on collocation...... for the catalytic chemistry of NH3 during simultaneous sulphur capture on a Stevns Chalk particle. The reduction of NO by NH3 over CaSO4 (which is the product of the reaction between SO2, O2 and limestone) was found to be important because this reaction could explain the change in selectivity with increased solid...

  11. Epilithic and endolithic bacterial communities in limestone from a Maya archaeological site.

    Science.gov (United States)

    McNamara, Christopher J; Perry, Thomas D; Bearce, Kristen A; Hernandez-Duque, Guillermo; Mitchell, Ralph

    2006-01-01

    Biodeterioration of archaeological sites and historic buildings is a major concern for conservators, archaeologists, and scientists involved in preservation of the world's cultural heritage. The Maya archaeological sites in southern Mexico, some of the most important cultural artifacts in the Western Hemisphere, are constructed of limestone. High temperature and humidity have resulted in substantial microbial growth on stone surfaces at many of the sites. Despite the porous nature of limestone and the common occurrence of endolithic microorganisms in many habitats, little is known about the microbial flora living inside the stone. We found a large endolithic bacterial community in limestone from the interior of the Maya archaeological site Ek' Balam. Analysis of 16S rDNA clones demonstrated disparate communities (endolithic: >80% Actinobacteria, Acidobacteria, and Low GC Firmicutes; epilithic: >50% Proteobacteria). The presence of differing epilithic and endolithic bacterial communities may be a significant factor for conservation of stone cultural heritage materials and quantitative prediction of carbonate weathering.

  12. Thermochemical degradation of limestone aggregate concrete on exposure to sodium fire

    International Nuclear Information System (INIS)

    Premila, M.; Sivasubramanian, K.; Amarendra, G.; Sundar, C.S.

    2008-01-01

    Limestone aggregate concrete blocks were subjected to sodium fire conforming to a realistic scenario in order to qualify them as protective sacrificial layers over structural concrete flooring in liquid metal-cooled fast breeder reactors. Mid infrared absorption measurements were carried out on these sodium fire-exposed samples as a function of depth from the affected surface. Definite signatures of thermochemical degradation indicating dehydration and structural modification of the limestone concrete have been obtained. Control runs were carried out to delineate the thermal effects of sodium fires from that of the chemical interaction effects. Measurements on limestone aggregate samples treated with fused NaOH provided direct evidence of the exact mechanism of the sodium attack on concrete. The observed degradation effects were correlated to the mechanical strength of the concrete blocks and to the intensity of the sodium fire experienced

  13. Elemental analysis of some West Malaysian limestones using neutron activation, delayed neutron and electron microprobe analysis

    International Nuclear Information System (INIS)

    Amin, Y.M.; Kamaluddin, B.; Mahat, R.H.

    1990-01-01

    Limestone stratigraphy in Malaysia has been and is dependent almost entirely in palaeontology. However fossil localities are sporadic and as such a new fossil discovery mean the necessity for a complete re-appraisal of the stratigraphy. The almost complete dependence upon palaeontology results from the difficulties of stratigraphy correlation of isolated outcrops, from the cover of tropical vegetation and from the often complex folding and faulting which has been imposed on the geosyn-clinical rocks by the Indonesian-Thai-Malayan orogeny. So by studying the elemental composition of limestones accurately, we would be able to correlate outcrops and other stratigraphic samples independent of fossil finds. The use of delayed neutron analysis would also determine the concentration of uranium and thorium accurately. This study, in conjunction with thermoluminescence and fission track studies, would able us to date the age of the limestones

  14. Industrial application of limestone deposits of kohat, NWFP: a research towards the sustainability of the deposits

    International Nuclear Information System (INIS)

    Bilqees, R.; Shah, T.

    2007-01-01

    Chemical analyses, petrographic studies and physical tests of limestone deposits in the vicinity of kohat along Bannu Road, Hangu Road and Rawalpindi Road were carried out to categorize these reserves, locality-wise, for their specified industrial uses. Limestone of kohat area was found to be generally good for construction purposes. The deposits on the Hangu Road were of good quality with more then 97% CaCO/sub 3/ and suitable for use in chemical, iron and steel industries, for glass making, soda ash manufacture etc. The deposit of Bannu Road with 96.5% CaCO/sub 3/ can be used for sugar refining, paint industry, flue gas desulphurization, animal feed etc. The limestone deposit of Rawalpindi Road is inferior in quality having 95.2% CaCO/sub 3/. It can be utilized in rubber industry, as ceramic whiting, building materials, rock wool etc. (author)

  15. Metal availability in technosols prepared with composted sewage sludge and limestone outcrop affected by the presence of barley

    Science.gov (United States)

    Román, Alejandro; Navarro-Pedreño, José; Belén Almendro-Candel, María; Gómez, Ignacio; Jordán, Manuel M.; Bech, Jaume

    2017-04-01

    The use of composted sewage sludge (SSC), and limestone outcrop residue (LOR), is a common practice in soil and land rehabilitation, technosol making, and quarry restoration (Jordán et al. 2008). Both wastes are used to improve the physical, chemical, and biological properties of impoverished soils (Karaca 2004; Jordão et al. 2006; Lovieno et al. 2009). However, the use of compost may have some negative effects on the environment (Navarro-Pedreño et al. 2004; Elridge et al. 2009). Moreover, plants cultivated in technosols can produced changes on the availability of essential and harmful metals and, for this reason, is necessary to made studies to evaluate the availability of metals and the effect of plants in their mobility and toxicity. In this experiment, it has been analyzed the effect of barley in metals availability in four technosols prepared mixing volumes of LOR (100, 98, 95 and 90 %) and SSC (0, 2, 5 and 10%). To determine the solubility and availability, Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn were measured by Lindsay-Norvell extraction procedure. For each technosoil, tree pots with barley (three plants) and three without barley were checked after 3 months A of them were irrigated with 1.5 L/week of tap water. At the end of this time, the metal solubility and availability were higher in soils with the presence of barley than the others. This was especially notorious for Fe and Zn. The presence of root exudates and the reduction of lixiviation due to plant transpiration can explain the highest presence of metals. This result may be considered in rhizosphere related to possible metal toxicity. Keywords: compost, limestone outcrop residues, heavy metals, barley. References: Eldridge SM, Chan KY, Barchia I, Pengelly PK, Katupitiya S, Davis JM (2009) A comparison of surface applied granulated biosolids and poultry litter in terms of risk to runoff water quality on turf farms in Western Sydney, Australia. Agr Ecosyst Environ doi:10.1016/j.agee.2009.07.007 Iovieno

  16. Response of the soil physical properties to restoration techniques in limestone quarries

    Science.gov (United States)

    Luna Ramos, Lourdes; Miralles Mellado, Isabel; Vignozzi, Nadia; Solé-Benet, Albert

    2016-04-01

    The devastating effects of soil erosion in mining areas from arid/semiarid environments have prompted efforts geared toward an improvement of the soil physical conditions for a fast establishment of vegetal cover. Restoration practices that increase soil moisture content are essential in drylands where rainfall is irregular or insufficient in order to accelerate ecological restoration. The aim of this study was to analyse the influence of organic amendments and mulches on the soil porosity as well as their impact on infiltration, five years after the beginning of an experimental restoration from limestone quarries in Sierra de Gádor (Almería, SE Spain). Nine plots 15 x 5 m were prepared at the site in a completely randomized 2 x 3 factorial design. The first factor, organic amendment, had three levels: sewage sludge (SA), compost from domestic organic residues (CA) and no amendment (NA). The second factor, mulches, also had three levels: gravel (GM), woodchip (WM) and no mulch (NM). In each experimental plot 75 native plants (Macrochloa tenacissima, Anthyllis terniflora and Anthyllis cytisoides) were planted. Infiltration was determined from rainfall simulations and soil porosity was assessed by image analysis of soil thin sections. Total porosity and pores distribution were measured according to pore shape (regular, irregular and elongated) and size (transmission pores [50-500 μm] and fissures [>500 μm]). Natural undisturbed soils around the mine area were used as a reference soil (RS). Restoration treatments showed higher total porosity, fissures and elongated pores than RS and we observed the highest values in treatments with WM. This fact is due to the disruption caused by the application of treatments rather that a good soil structure. Each combination exhibited different values of transmission pores, being greater in the combinations of NA-GM, SA-NM and CA-WM. Infiltration increased with the increase of the total porosity, fissures and elongated pores

  17. Aqueous recovery of plutonium from pyrochemical processing residues

    International Nuclear Information System (INIS)

    Gray, L.W.; Gray, J.H.

    1984-01-01

    Pyrochemical processes provide rapid methods to reclaim plutonium from scrap residues. Frequently, however, these processes yield an impure plutonium product and waste residues that are contaminated with actinides and are therefore nondiscardable. The Savannah River Laboratory and Plant and the Rocky Flats Plant are jointly developing new processes using both pyrochemistry and aqueous chemistry to generate pure product and discardable waste. An example of residue being treated is that from the molten salt extraction (MSE), a mixture of NaCl, KCl, MgCl 2 , PuCl 3 , AmCl 3 , PuO 2 , and Pu 0 . This mixture is scrubbed with molten aluminum containing a small amount of magnesium to produce a nonhomogeneous Al-Pu-Am-Mg alloy. This process, which rejects most of the NaCl-KCl-MgCl 2 salts, results in a product easily dissolved in 6M HNO 3 -0.1M HF. Any residual chloride in the product is removed by precipitation with Hg(I) followed by centrifuging. Plutonium and americium are then separated by the standard Purex process. The americium, initially diverted to the solvent extraction waste stream, can either be recovered or sent to waste

  18. Sedimentary and environmental history of the Late Permian Bonikowo Reef (Zechstein Limestone, Wuchiapingian, western Poland

    Directory of Open Access Journals (Sweden)

    Paweł Raczyński

    2017-07-01

    Full Text Available The Bonikowo Reef occurs in the central part of the Zechstein Limestone Basin in western Poland and was growing on the topmost edges of tilted blocks and/or on the top of uplifted horsts of the Brandenburg–Wolsztyn–Pogorzela High. Its size is ca. 1.6 km2. The Bonikowo Reef shows the thickest reef section (90.5 m recorded in the High. The Zechstein Limestone unit is represented mostly by limestones, often thoroughly recrystallized, although the macrotextures and biota of the boundstone are identifiable in most cases. The drillcore section is a mixture of boundstones (microbial and bryozoan, wackestones, packstones and grainstones, which often co-occur. The δ13C and δ18O values for both calcite (avg. 3.8 ± 0.8‰ and −3.4 ± 1.7‰, respectively and dolomite (avg. 3.5 ± 0.7‰ and −5.2 ± 1.3‰, respectively are transitional between the values previously reported for condensed sequences of the basinal facies and larger reef complexes. The biofacies of the Bonikowo Reef are very similar to those recognized in other reefs of the Brandenburg–Wolsztyn–Pogorzela High, which owe their origin to the destruction of bryozoan boundstones. The biota composition is typical and characteristic of other Zechstein Limestone reefs. However, the Bonikowo Reef demonstrates the importance of microbialites, laminar and nodose encrustations, in the growth and cohesion of the Zechstein Limestone reefs. Such encrustations abound within the Zechstein Limestone although, in many cases, the real nature of the encrustations is difficult to ascertain. These laminated encrustations show great similarity to Archaeolithoporella that is one of the most important Permian reef-building organisms. The encrustations considered to represent Archaeolithoporella were also previously recorded in the Zechstein Limestone of western Poland and in its stratigraphic equivalent, the Middle Magnesian Limestone of Northeast England. The lower part of the sequence shows

  19. Pliocene Te Aute limestones, New Zealand : expanding concepts for cool-water shelf carbonates

    International Nuclear Information System (INIS)

    Nelson, C.S.; Winefield, P.R.; Hood, S.D.; Caron, V.; Pallentin, A.; Kamp, P.J.J.

    2003-01-01

    Acceptance of a spectrum of warm- through cold-water shallow-marine carbonate facies has become of fundamental importance for correctly interpreting the origin and significance of all ancient platform limestones. Among other attributes, properties that have become a hallmark for characterising many Cenozoic non-tropical occurrences include: (1) the presence of common bryozoan and epifaunal bivalve skeletons; (2) a calcite-dominated mineralogy; (3) relatively thin deposits exhibiting low rates of sediment accumulation; (4) an overall destructive early diagenetic regime; and (5) that major porosity destruction and lithification occur mainly in response to chemical compaction of calcitic skeletons during moderate to deep burial. The Pliocene Te Aute limestones are non-tropical skeletal carbonates formed at paleolatitudes near 40-42 degrees S under the influence of commonly strong tidal flows along the margins of an actively deforming and differentially uplifting forearc basin seaway, immediately inboard of the convergent Pacific-Australian plate boundary off eastern North Island, New Zealand. This dynamic depositional and tectonic setting strongly influenced both the style and subsequent diagenetic evolution of the limestones. Some of the Te Aute limestones exhibit the above kinds of 'normal' non-tropical characteristics, but others do not. For example, many are barnacle and/or bivalve dominated, and several include attributes that at least superficially resemble properties of certain tropical carbonates. In this regard, a number of the limestones are infaunal bivalve rich and dominated by an aragonite over a calcite primary mineralogy, with consequently relatively high diagenetic potential. Individual limestone units are also often rather thick (e.g., up to 50-300 m), with accumulation rates from 0.2 to 0.5 m/ka, and locally as high as 1 m/ka. Moreover, there can be a remarkable array of diagenetic features in the limestones, involving grain alteration and

  20. Rapid method to determine actinides and 89/90Sr in limestone and marble samples

    International Nuclear Information System (INIS)

    Maxwell, S.L.; Culligan, Brian; Hutchison, J.B.; Utsey, R.C.; Sudowe, Ralf; McAlister, D.R.

    2016-01-01

    A new method for the determination of actinides and radiostrontium in limestone and marble samples has been developed that utilizes a rapid sodium hydroxide fusion to digest the sample. Following rapid pre-concentration steps to remove sample matrix interferences, the actinides and 89 / 90 Sr are separated using extraction chromatographic resins and measured radiometrically. The advantages of sodium hydroxide fusion versus other fusion techniques will be discussed. This approach has a sample preparation time for limestone and marble samples of <4 h. (author)

  1. Improvement of operational properties of shell limestone building materials by polysulfide solution impregnation

    Directory of Open Access Journals (Sweden)

    MASSALIMOV Ismail Alexandrovich

    2017-06-01

    Full Text Available The data of studies on the effectiveness of impregnation with polysulfide solutions of shell limestone used as facing and wall material, as well as for the manufacture of road products are presented. Modification of the limestone with the impregnating composition «Akvastat» created by the authors which is sulfur-containing water-based solution of calcium polysulfide containing alcohols and surfactants, can significantly reduce water absorption and increase durability of limestone. Impregnating composition on the basis of calcium polysulfide possesses density of 1.22–1.24 g/cm3, the infiltrant penetrates into the pore structure of limestone to a depth of 4 cm or more, depending on the density and structure of the sample. While the material is drying, sulfur nanoparticles are crystallized from the polysulfide solution in its pores. They partially fill pore space and form protective durable insoluble hydrophobic coating that impedes the penetration of water into the pores of the limestone, but preserves its vapor permeability, which is important for wall and decoration materials. The evaluation of protective coatings was performed with laser particle size analyzer, scanning probe microscope and a diffractometer. It showed that the average size of the particles forming the protective coating is in the range of 20–25 nm, the particles shape is spherical, the particles are elemental sulfur with orthorhombic structure of the crystal lattice. The processing of shell limestone with calcium polysulphide solution provides formation of coating based on nanosized sulfur on the surface of stone pores. The coating partially fills the pore space and, as it is hydrophobic, reduces the water absorption of the samples by a factor of 5–8, increases their average density by 22–27%, strength in 1,2–1,3 times, the softening factor by 6–19%, that makes possible to predict the increase of the durability of building materials based on shell limestone to 1

  2. Performance of japanese quails fed feeds containing different corn and limestone particle sizes

    OpenAIRE

    Berto,DA; Garcia,EA; Móri,C; Faitarone,ABG; Pelícia,K; Molino,AB

    2007-01-01

    This study aimed at evaluating performance and egg quality of Japanese quails fed feeds containing different corn and limestone particle sizes. A total number of 648 birds in the peak of production was distributed in a random complete block experimental design, using a 2x3 factorial arrangement (2 corn particle sizes and 3 limestone particle sizes). Birds were designated to one of two blocks, with six replicates of 18 birds each. Mean geometric diameter (MGD) values used were 0.617mm and 0.72...

  3. Hydration of Blended Portland Cements Containing Calcium-Aluminosilicate Glass Powder and Limestone

    DEFF Research Database (Denmark)

    Moesgaard, M; Poulsen, Søren Lundsted; Herfort, D

    2012-01-01

    M. MOESGAARD, S.L. POULSEN, D. HERFORT, M. STEENBERG, L.F. KIRKEGAARD, J. SKIBSTED, Y. YUE, Hydration of Blended Portland Cements Containing Calcium-Aluminosilicate Glass Powder and Limestone, Journal of the American Ceramic Society 95, 403 – 409 (2012).......M. MOESGAARD, S.L. POULSEN, D. HERFORT, M. STEENBERG, L.F. KIRKEGAARD, J. SKIBSTED, Y. YUE, Hydration of Blended Portland Cements Containing Calcium-Aluminosilicate Glass Powder and Limestone, Journal of the American Ceramic Society 95, 403 – 409 (2012)....

  4. Differences between silica and limestone concretes that may affect their interaction with corium

    International Nuclear Information System (INIS)

    Journeau, C.; Haquet, J. F.; Piluso, P.; Bonnet, J. M.

    2008-01-01

    Recent Molten Core Concrete Interaction tests performed at Argonne National Laboratory and at CEA Cadarache have shown that, whereas the ablation of limestone-rich concretes is almost isotropic, the ablation of silica-rich concretes is much faster towards the sides than towards the bottom of the cavity. The following differences exists between limestone-rich and silica-rich concretes: limestone concretes liberate about twice as much gas, at a given ablation rate than siliceous concretes (more than 50% more at constant heat flux) and this can affect pool hydraulics and crust stability: limestone concrete has a higher liquidus temperature than siliceous concrete and molten limestone concrete has a larger diffusion coefficient and can more easily dissolve a corium crust than siliceous melt; limestone aggregates are destroyed by de-carbonation at around 1000 K while silica aggregates melt only above 2000 K, so that floating silica aggregates can form cold spots increasing corium solidification near the interface; de-carbonation of limestone leads to a significant shrinkage of concrete melt volume compared to the cold solid that hampers the mechanical stability of overlying crusts; the chemical composition of molten mortar (sand + cement) and concrete (sand + gravel + cement) is close for limestone-rich concretes while it is different for siliceous concretes, so that the melt composition may vary significantly in case of non-simultaneous melting of the siliceous concrete constituents; molten silicates have a large viscosity, so that transport properties are different for the two types of concretes. The small range of plant concrete compositions that have been considered for MCCI experiments has not yet been found sufficient to determine which of the above-mentioned differences is paramount to explain the observed difference in ablation patterns. Separate Effect Tests using specially-designed 'artificial concretes' and prototypic corium would provide the necessary

  5. Carbonate Minerals with Magnesium in Triassic Terebratula Limestone in the Term of Limestone with Magnesium Application as a Sorbent in Desulfurization of Flue Gases

    Science.gov (United States)

    Stanienda-Pilecki, Katarzyna

    2017-09-01

    This article presents the results of studies of Triassic (Muschelkalk) carbonate rock samples of the Terebratula Beds taken from the area of the Polish part of the Germanic Basin. It is the area of Opole Silesia. The rocks were studied in the term of possibility of limestone with magnesium application in desulfurization of flue gases executed in power plants. Characteristic features of especially carbonate phases including magnesium-low-Mg calcite, high-Mg calcite, dolomite and huntite were presented in the article. They were studied to show that the presence of carbonate phases with magnesium, especially high-Mg calcite makes the desulfurization process more effective. Selected rock samples were examined using a microscope with polarized, transmitted light, X-ray diffraction, microprobe measurements and FTIR spectroscopy. The results of studies show a domination of low magnesium calcite in the limestones of the Terebratula Beds. In some samples dolomite and lower amounts of high-Mg calcite occurred. Moreover, huntite was identified. The studies were very important, because carbonate phases like high-Mg calcite and huntite which occurred in rocks of the Triassic Terebratula Beds were not investigated in details by other scientists but they presence in limestone sorbent could influence the effectiveness of desulfurization process.

  6. The impact of river infiltration on the chemistry of shallow groundwater in a reclaimed water irrigation area.

    Science.gov (United States)

    Yin, Shiyang; Wu, Wenyong; Liu, Honglu; Bao, Zhe

    2016-10-01

    Reclaimed water reuse is an effective method of alleviating agricultural water shortages, which entails some potential risks for groundwater. In this study, the impacts of wastewater reuse on groundwater were evaluated by combination of groundwater chemistry and isotopes. In reclaimed water infiltration, salt composition was affected not only by ion exchange and dissolution equilibrium but also by carbonic acid equilibrium. The dissolution and precipitation of calcites and dolomites as well as exchange and adsorption between Na and Ca/Mg were simultaneous, leading to significant changes in Na/Cl, (Ca+Mg)/Cl, electrical conductivity (EC) and sodium adsorption ratio (SAR). The reclaimed water was of the Na-Mg-Ca-HCO 3 -Cl type, and groundwater recharged by reclaimed water was of the Na-Mg-HCO 3 and Mg-Na-HCO 3 types. The hydrogeological conditions characterized by sand-clay alternation led to both total nitrogen (TN) and total phosphorus (TP) removal efficiencies >95%, and there was no significant difference in those contents between aquifers recharged by precipitation and reclamation water. >40years of long-term infiltration and recharge from sewage and reclaimed water did not cause groundwater contamination by nitrogen, phosphorus and heavy metals. These results indicate that characteristics of the study area, such as the lithologic structure with sand-clay alternation, relatively thick clay layer, and relatively large groundwater depth have a significant role in the high vulnerability. Copyright © 2016 Elsevier B.V. All rights reserved.

  7. Impact of reclaimed water irrigation on soil salinity, hydraulic conductivity, cation exchange capacity and macro-nutrients

    Directory of Open Access Journals (Sweden)

    Saif A. Al-Khamisi

    2016-01-01

    Full Text Available Field studies were conducted at Agriculture Research Center, Oman during the year 2010/2011 to monitor the impact of reclaimed water irrigation on soil physical and chemical properties after wheat, cowpea and maize cultivation (in rotation. Three different water sources (Groundwater (GW, desalinized water (DW, and Reclaimed Water (RW were used as the treatments in Randomized Completely Block Design (RCBD with 3 blocks (replicates. Samples were taken from four depths (30, 45, 60 and 90 cm after harvesting time of the three crops. Soil salinity (ECe in all soil depths decreased with time. Organic carbon did not show significant difference between harvest timings of wheat and cowpea. Organic carbon increased with time in soil irrigated with reclaimed water. The saturated hydraulic conductivity of the soil, Ksat didn’t show significant difference among the water types and their interaction with soil depths. Total nitrogen was the highest after cowpea harvest in reclaimed water irrigation. The soil phosphorus and potassium were not affected by any of the three water irrigation types. The highest concentrations of phosphorus and potassium were found to be in the upper soil layers. Overall, no adverse impacts of reclaimed water irrigation were observed after growing three crops of rotation.

  8. Exploring the Patterns and Mechanisms of Reclaimed Arable Land Utilization under the Requisition-Compensation Balance Policy in Wenzhou, China

    Directory of Open Access Journals (Sweden)

    Lin Lin

    2017-12-01

    Full Text Available Arable land in China is undergoing significant changes, with massive losses of arable land due to rapid urbanization and the reclamation of arable land from other lands to compensate for these losses. Many studies have analyzed arable land loss, but less attention has been paid to land reclamation, and the utilization of reclaimed land remains unclear. The goal of our study was to characterize the patterns and efficiency of the utilization of reclaimed land and to identify the factors influencing the land utilization process in Wenzhou using remote sensing, geographic information systems and logistic regression. Our results showed that only 37% of the total reclaimed land area was under cultivation, and other lands were still bare or had been covered by trees and grasses. The likelihood that reclaimed land was used for cultivation was highly correlated with the land use type of its neighboring or adjacent parcels. Reclaimed land utilization was also limited at high elevations in lands with poor soil fertility and in lands at a great distance from rural residential areas. In addition, parcels located in the ecological protection zone were less likely to be cultivated. Therefore, we suggest that the important determinants should be considered when identifying the most suitable land reclamation areas.

  9. Investigation of Geochemical Characteristics and Controlling Processes of Groundwater in a Typical Long-Term Reclaimed Water Use Area

    Directory of Open Access Journals (Sweden)

    Yong Xiao

    2017-10-01

    Full Text Available The usage of reclaimed water can efficiently mitigate water crises, but it may cause groundwater pollution. To clearly understand the potential influences of long-term reclaimed water usage, a total of 91 samples of shallow and deep groundwater were collected from a typical reclaimed water use area during the dry and rainy seasons. The results suggest both shallow and deep groundwater are mainly naturally alkaline freshwater, which are composed mainly of Ca-HCO3, followed by mixed types such as Ca-Na-HCO3 and Ca-Mg-HCO3. A seasonal desalination trend was observed in both shallow and deep aquifers due to dilution effects in the rainy season. Groundwater chemical compositions in both shallow and deep aquifers are still dominantly controlled by natural processes such as silicate weathering, minerals dissolution and cation exchange. Human activities are also the factors influencing groundwater chemistry. Urbanization has been found responsible for the deterioration of groundwater quality, especially in shallow aquifers, because of the relative thin aquitard. Reclaimed water usage for agricultural irrigation and landscape purposes has nearly no influences on groundwater quality in rural areas due to thick aquitards. Therefore, reclaimed water usage should be encouraged in arid and semiarid areas with proper hydrogeological condition.

  10. Accumulation of contaminants of emerging concern in food crops-part 1: Edible strawberries and lettuce grown in reclaimed water.

    Science.gov (United States)

    Hyland, Katherine C; Blaine, Andrea C; Dickenson, Eric R V; Higgins, Christopher P

    2015-10-01

    Contaminants of emerging concern present in domestic waste streams include a highly diverse group of potentially biologically active compounds that can be detected at trace levels in wastewater. Concerns about potential uptake into crops arise when reclaimed water is used in food crop production. The present study investigated how 9 contaminants of emerging concern in reclaimed water are taken up into edible portions of two food crops. Two flame retardant chemicals, tris(1-chloro-2-propyl) phosphate (TCPP) and tris(2-chloroethyl) phosphate (TCEP) and several polar pharmaceuticals (carbamazepine, diphenhydramine, sulfamethoxazole, and trimethoprim) accumulated in a linear, concentration-dependent manner in lettuce (Lactuca sativa) irrigated with reclaimed water, suggesting passive uptake of both neutral and ionizable chemical contaminants in lettuce. Furthermore, concentration-dependent accumulation of TCEP and TCPP from reclaimed water was also observed in strawberry fruits (Fragaria ananassa). Collectively, these data suggest that highly polar or charged contaminants can be taken up by crops from water bearing contaminants of emerging concern and can be accumulated in the edible portions. Using these data, however, estimates of human exposure to these contaminants from reclaimed water food crop accumulation suggest that exposure to the contaminants of emerging concern examined in the present study is likely substantially lower than current exposure guidelines. © 2015 SETAC.

  11. Diagenetic evolution and stable isotopes of Lower Permian platform marginal carbonates (Trogkofel Limestone, Carnic Alps, Austria)

    Science.gov (United States)

    Schaffhauser, Maria; Krainer, Karl; Sanders, Diethard Gerald; Spötl, Christoph

    2010-05-01

    The Trogkofel massif in the Carnic Alps, Austria/Italy, consists of a succession up to 400 m thick of limestones deposited along a platform margin (Trogkofel Limestone; Artinskian). The top of the Trogkofel Limestone is erosively overlain by the Tarvis Breccia. Up-section, the Trogkofel Limestone consists of well-bedded shallow-water bioclastic limestones with intercalated mud mounds, overlain by thick-bedded to unbedded limestones (bioclastic grainstones, packstones, rudstones) and cementstone mounds rich in phylloid algae, Tubiphytes, bryozoans and Archaeolithoporella. In the cementstone mounds, bioclasts are coated by thick fringes and botryoids of fibrous calcite, and of calcite spar that probably represents calcitized aragonite. Primary and intrinsic pores are filled by microbialite, and/or by mudstone to bioclastic wackestone. Shallow-water bioclastic grainstones are cemented by isopachous fringes of fibrous calcite, or by sparry calcite. Throughout the succession, evidence for meteoric-vadose dissolution is present. The Trogkofel Limestone is riddled by palaeokarstic dykes and caverns filled by (a) isopachous cement fringes up to a few decimetres thick, and/or (b) by red, geopetally-laminated lime mudstone to bio-lithoclastic wackestone; geopetal laminasets locally display convolute bedding. Small dissolution cavities are filled by grey internal sediment, or by crystal silt. Brecciated internal sediments overlain by unbrecciated, geopetally-laminated infillings record deformation during or after deposition of the Trogkofel Limestone. Polyphase fractures cemented by calcite may cross-cut both internal sediments and host rock. In the Trogkofel Limestone, local dolomitization is common. Replacement dolomites show a wide range of shapes and fabrics, including: (a) fine-crystalline anhedral xenotopic fabric, (b) coarse-crystalline subhedral to euhedral, hypidiotopic to idiotopic fabric of turbid or optically zoned crystals, and (c) saddle dolomite as replacement

  12. Submarine terrace limestones from the continental slope off Saurashtra-Bombay: Evidence of Late Quaternary neotectonic activity

    Digital Repository Service at National Institute of Oceanography (India)

    Rao, V.P.; Veerayya, M.

    cements occur as isopachous crusts. Dissolution and clotting of aragonite needles and drusy calcite in the interstices indicate cementation of the limestones at inter-tidal conditions. The age of the limestones is 11,900 years BP. These imply that the 130...

  13. Replacement of Eocene white sandy limestone in historical buildings : over 100 years of practice in the Netherlands

    NARCIS (Netherlands)

    Quist, W.J.; Nijland, T.G.; Hees, R.P.J. van

    2013-01-01

    This paper discusses the replacement of white sandy limestone (Gobertange and Lede or Balegem) in the Netherlands in (successive) restorations from the mid-19th century onwards. White sandy limestone, transported from the southern part of the Low Countries (now Belgium), was extensively used in the

  14. Lithofacies and petrophysical properties of Portland Base Bed and Portland Whit Bed limestone as related to durability

    NARCIS (Netherlands)

    Dubelaar, C.W.; Engering, S.; Hees, R.P.J. van; Koch, R.; Lorenz, H.G.

    2003-01-01

    This study focuses on the differences in lithofacies and petrophysical properties of Base Bed and Whit Bed Portland limestone and the presumed relationships between these characteristics and the durability of this building stone. As Portland limestone probably will be used as a stone for several

  15. Lithofacies and Petrophysical Properties of Portland Base Bed and Portland Whit Bed Limestone as Related to Durability

    NARCIS (Netherlands)

    Dubelaar, C.W.; Engering, S.; Van Hees, R.P.J.; Koch, R.; Lorenz, H.G.

    2003-01-01

    This study focuses on the differences in lithofacies and petrophysical properties of Base Bed and Whit Bed Portland limestone and the presumed relationships between these characteristics and the durability of this building stone. As Portland limestone probably will be used as a stone for several

  16. High-temperature CO2 capture cycles of hydrated limestone prepared with aluminum (hydr)oxides derived from kaolin

    International Nuclear Information System (INIS)

    Wang, Ke; Zhao, Pengfei; Guo, Xin; Han, Dongtai; Chao, Yang

    2014-01-01

    Highlights: • Hydrated limestone exhibited a higher reactivity and stability. • Microstructure of hydrated limestone was significantly improved. • Hydrated limestone still suffered less loss-incapacity. • Hydrated limestone sorbents with kaolin-based binders were prepared and characterized. • Sorbents prepared from hydrated limestone and Al(OH) 3 binder are a promising sorbent. - Abstract: A simple and convenient process was used to improve the utilization of natural limestone and kaolin for calcium looping technology and environmental applications. The calcined natural limestone modified with the distilled water (denoted as Limestone-W), was systematically studied and compared with the other CaO sorbents (calcium acetate, calcium D-gluconate and calcined natural limestone). These CaO-based sorbents were tested for their CO 2 capture behavior through 20 carbonation/calcination cycles in a thermo-gravimetric analyzer (TGA). Their morphology, pore structure and phase composition before and after carbonation/calcination cycles were determined by scanning electron microscopy, nitrogen adsorption, and X-ray diffraction. The first-cycle and multicycle sorption results revealed that the Limestone-W sorbent exhibited a relatively faster reaction rate and higher cyclic CO 2 capture. The characterization data indicated that the Limestone-W was composed of a special calcium oxide structure with lower crystalline and higher porosity nanoparticles, which appeared to be the main reasons for its higher CO 2 capture capability. However, the Limestone-W still suffered loss of reactivity, even though it was less pronounced than the other CaO sorbent. To avoid this unfavorable effect, a thermally stable inert material (aluminum hydroxide derived from kaolin) was incorporated into the Limestone-W structure. This new sorbent revealed higher stability because the formation of a stable framework of Ca 12 Al 14 O 33 particles hindered densification and sintering of the CaO phase

  17. Characteristics of labile organic carbon fractions in reclaimed mine soils: Evidence from three reclaimed forests in the Pingshuo opencast coal mine, China.

    Science.gov (United States)

    Yuan, Ye; Zhao, Zhongqiu; Li, Xuezhen; Wang, Yangyang; Bai, Zhongke

    2018-02-01

    The reclamation of discarded spoils has the potential to stimulate carbon (C) sequestration in reclaimed mine soils (RMSs). Nevertheless, to date the temporal dynamics of labile organic C fractions have not been sufficiently elucidated in RMSs. In this study, soil organic carbon (SOC) and labile organic C fractions, including microbial biomass organic C (MBC), easily oxidizable organic C (EOC) and dissolved organic C (DOC), were determined in Robinia pseudoacacia monoculture forests (reclamation periods of 0, 8, 10, 13, 15, 18 and 30years), Pinus tabuliformis forests (reclamation periods of 0, 10, 19, 23 and 25years) and Ulmus pumila forests (reclamation periods of 0, 18, 20 and 22years) situated on RMSs in the Pingshuo opencast coal mine, China. Changes in labile organic C fractions within the soil profiles (0-100cm) were also identified at the 18- or 19-year plots under the three monoculture forests. Our results showed that, SOC and labile organic C fractions, together with soil microbial quotient (SMQ) and C management index (CMI), increased with time since reclamation, indicating that the quality of RMSs improved over time after initial reclamation under the three forest types. R. pseudoacacia significantly increased the accretion of SOC and EOC in the early stage of reclamation while P. tabuliformis accelerated the accumulation of the MBC fraction. Results for U. pumila indicated that this species had a better ability to store C in RMSs 10years or more after reclamation. SOC and labile organic C fractions both had S-shaped distributions within the soil profiles (0-100cm), with the 0-20cm layer recording the highest values (Pfractions were closely associated and correlated with soil physicochemical properties; our results also showed that nitrogen played an important role in the development of labile organic C fractions. Overall, reclamation accelerated the accretion of both SOC and labile organic C fractions, results of which varied among the reclaimed forests

  18. Lightweight concrete with Algerian limestone dust. Part II: study on 50% and 100% replacement to normal aggregate at timely age

    Directory of Open Access Journals (Sweden)

    S. Kitouni

    2015-12-01

    Full Text Available Abstract A control lightweight concrete (LWC mixture made with 50% and 100% of limestone as a replacement of coarse aggregates in weight was prepared. Limestone is used for economical and environmental concern. The concrete samples were cured at 65% relative humidity at 20 ºC. The compressive and flexural tensile strengths, elastic modulus and Poisson's ratio of hardened concrete were measured. Laboratory compressive and tensile strength tests results showed that LWC can be produced by the use of limestone. The aim of this study is twofold: one is to design a lightweight concrete with the use of limestone that will provide an advantage of reduction in dead weight of a structure; and second is to obtain a more economical LWC mixture with the use of limestone.

  19. Influence of limestone fillers on combustion characteristics of asphalt mortar for pavements

    DEFF Research Database (Denmark)

    Ke, Wu; Kai, Zhu; Wu, Hao

    2014-01-01

    Asphalt materials will be ignited and release significant toxic fumes within tunnel fires. Thus, combustion characteristics of asphalt materials used in road tunnel should be studied in order to limit such an adverse effect. In the present work we study the influence of limestone fillers on combu...

  20. Model of fragmentation of limestone particles during thermal shock and calcination in fluidised beds

    Energy Technology Data Exchange (ETDEWEB)

    Saastamoinen, J.; Pikkarainen, T.; Tourunen, A.; Rasanen, M.; Jantti, T. [VTT Technical Research Center, Jyvaskyla (Finland)

    2008-11-15

    Fragmentation of limestone due to thermal shock and calcination in a fluidised bed was studied through experiments and modelling. The time for heating was estimated by model calculations and the time for calcination by measurements. Fragmentation due to thermal shock was carried out by experiments in a CO{sub 2} atmosphere in order to prevent the effect of calcination. It was found to be much less than fragmentation due to calcination. Average particle sizes before and after fragmentation are presented for several types of limestone. The effects of particle size and gas composition on the primary fragmentation were studied through experiments. Increasing the fluidisation velocity increased the tendency to fragment. The evolution of the particle size distribution (PSD) of limestone particles due to thermal shock and during calcination (or simultaneous calcination and sulphation) were calculated using a population balance model. Fragmentation due to thermal shock is treated as an instantaneous process. The fragmentation frequency during calcination is presented as exponentially decaying over time. In addition to the final PSD, this model also predicts the PSD during the calcination process. The fragmentation was practically found to end after 10 min. Furthermore. a population balance method to calculate the particle size distribution and amount of limestone in fluidised beds in dynamic and steady state, when feeding history is known, is presented.

  1. Limestone particle attrition and size distribution in a small circulating fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Zhongxiang Chen; John R. Grace; C. Jim Lim [University of British Columbia, Vancouver, BC (Canada). Department of Chemical and Biological Engineering

    2008-06-15

    Limestone particle attrition was investigated in a small circulating fluidized bed reactor at temperatures from 25 to 850{sup o}C, 1 atm pressure and superficial gas velocities from 4.8 to 6.2 m/s. The effects of operating time, superficial gas velocity and temperature were studied with fresh limestone. No calcination or sulfation occurred at temperatures {le} 580{sup o}C, whereas calcination and sulfation affected attrition at 850{sup o}C. Increasing the temperature (while maintaining the same superficial gas velocity) reduced attrition if there was negligible calcination. Attrition was high initially, but after about 24 h, the rate of mass change became constant. The ratio of initial mean particle diameter to that at later times increased linearly with time and with (U{sub g} - U{sub mf}){sup 2}, while decreasing exponentially with temperature, with an activation energy for fresh limestone of -4.3 kJ/mol. The attrition followed Rittinger's surface theory. The change of surface area of limestone particles was proportional to the total excess kinetic energy consumed and to the total attrition time, whereas the change of surface area decreased exponentially with increasing temperature. At 850{sup o}C, the attrition rate of calcined lime was highest, whereas the attrition rate was lowest for sulfated particles. When online impact attrition was introduced, the attrition rate was about an order of magnitude higher than without impacts. 25 refs., 14 figs., 4 tabs.

  2. Performance Monitoring: Evaluating an Organic Carbon-Limestone PRB for Treatment of Heavy Metals and Acidity

    Science.gov (United States)

    Since 2004, researchers from the U.S. EPA National Risk Management Research Laboratory (NRMRL) have annually evaluated performance of an organic carbon-limestone permeable reactive barrier (PRB) system installed in 2003 by EPA Region 6 at the Delatte Metals Superfund site in Ponc...

  3. Attrition of limestones by impact loading in fluidized beds: The influence of reaction conditions

    Energy Technology Data Exchange (ETDEWEB)

    Scala, Fabrizio [Istituto di Ricerche sulla Combustione, Consiglio Nazionale delle Ricerche, Napoli (Italy); Salatino, Piero [Istituto di Ricerche sulla Combustione, Consiglio Nazionale delle Ricerche, Napoli (Italy); Dipartimento di Ingegneria Chimica, Universita degli Studi di Napoli Federico II, Napoli (Italy)

    2010-09-15

    The extent of attrition associated with impact loading was studied for five different limestones pre-processed in fluidized bed under different reaction conditions. The experimental procedure was based on the measurement of the amount and the particle size distribution of the debris generated upon impact of sorbent samples against a target at velocities between 10 and 45 m/s. The effect of calcination, sulfation and calcination/re-carbonation on impact damage was assessed. Fragmentation by impact loading of the limestones was significant and increased with the impact velocity. Lime samples displayed the largest propensity to undergo impact damage, followed by sulfated, re-carbonated and raw limestones. Fragmentation of the sulfated samples followed a pattern typical of the failure of brittle materials. On the other hand, the behaviour of lime samples better conformed to a disintegration failure mode, with extensive generation of very fine fragments. Raw limestone and re-carbonated lime samples followed either of the two patterns depending on the sorbent nature. The extent of particle fragmentation increased after multiple impacts, but the incremental amount of fragments generated upon one impact decreased with the number of successive impacts. (author)

  4. Optimization of nanolime solvent for the consolidation of coarse porous limestone

    Science.gov (United States)

    Borsoi, Giovanni; Lubelli, Barbara; van Hees, Rob; Veiga, Rosário; Silva, António Santos

    2016-09-01

    The potentialities of nanomaterials for application in the field of conservation have been widely investigated in the last two decades. Among nanomaterials, nanolimes, i.e., dispersions of lime nanoparticles in alcohols are promising consolidating products for calcareous materials. Nanolimes are effective in recovering the very superficial loss of cohesion of decayed materials, but they do not always provide sufficient mass consolidation. This limitation is mainly related to the deposition of the nanoparticles nearby the surface of the material. Experimental research has been set up with the aim of improving the in-depth deposition of lime nanoparticles. Previous research by the authors has shown that nanolime deposition within a substrate can be controlled by adapting the nanolimes properties (kinetic stability and evaporation rate) to the moisture transport behavior of the substrate. Nanolime properties can be modified by the use of different solvents. In this research, nanolime dispersions have been further optimized for application on Maastricht limestone, a coarse porous limestone. Firstly, nanolimes were synthesized and dispersed in ethanol and/or water, both pure and mixed in different percentages. Subsequently, based on the kinetic stability of the nanolime dispersions, the most promising solvent mixtures were selected and applied on the limestone. The deposition of lime nanoparticles within the limestone was studied by phenolphthalein test, optical microscopy and scanning electron microscopy. The results confirm that nanolime dispersed in a mixture of ethanol (95 %) and water (5 %) can guarantee a better nanoparticles in-depth deposition within coarse porous substrates, when compared to dispersions in pure ethanol.

  5. Use of limestone obtained from waste of the mussel cannery industry for the production of mortars

    International Nuclear Information System (INIS)

    Ballester, Paloma; Marmol, Isabel; Morales, Julian; Sanchez, Luis

    2007-01-01

    Various types of cement-SiO 2 -CaCO 3 mortar were prepared by replacing quarry limestone aggregate with limestone obtained as a by-product from waste of the mussel cannery industry. The CaCO 3 aggregate consists mainly of elongated prismatic particles less than 4 μm long rather than of the rounded particles of smaller size (2-6 μm) obtained with quarry limestone. The mechanical and structural properties of the mortars were found to be influenced by aggregate morphology. Setting of the different types of mortar after variable curing times was evaluated by scanning electron microscopy (SEM), thermogravimetric analysis (TG) and mercury intrusion porosimetry (MIP) techniques. Mortars with a high content in mussel shell limestone exhibited a more packed microstructure, which facilitates setting of cement and results in improved mortar strength. The enhanced mechanical properties of the new mortars allow the cement content in the final mortar composition to be decreased and production costs to be reduced as a result

  6. Conceptualization of flow and transport in a limestone aquifer by multiple dedicated hydraulic and tracer tests

    DEFF Research Database (Denmark)

    Mosthaf, Klaus; Brauns, Bentje; Fjordbøge, Annika Sidelmann

    2018-01-01

    Limestone aquifers are of great interest as a drinking water resource in many countries. They often have a complex crushed and fractured geology, which makes the analysis and description of flow and transport processes in such aquifers a challenging task. In this study, the solute transport behav...

  7. Lateral capacity of rock sockets in limestone under cyclic and repeated loading.

    Science.gov (United States)

    2010-08-01

    This report contains the results from full scale lateral load testing of two short rock socketed shafts in : limestone, and the development of recommendations for p-y analysis using those results. Two short shafts 42 : inches in diameter were constru...

  8. Effects of limestone petrography and calcite microstructure on OPC clinker raw meals burnability

    Science.gov (United States)

    Galimberti, Matteo; Marinoni, Nicoletta; Della Porta, Giovanna; Marchi, Maurizio; Dapiaggi, Monica

    2017-10-01

    Limestone represents the main raw material for ordinary Portland cement clinker production. In this study eight natural limestones from different geological environments were chosen to prepare raw meals for clinker manufacturing, aiming to define a parameter controlling the burnability. First, limestones were characterized by X-Ray Fluorescence, X-Ray Powder Diffraction and Optical Microscopy to assess their suitability for clinker production and their petrographic features. The average domains size and the microstrain of calcite were also determined by X-Ray Powder Diffraction line profile analysis. Then, each limestone was admixed with clay minerals to achieve the adequate chemical composition for clinker production. Raw meals were thermally threated at seven different temperatures, from 1000 to 1450 °C, to evaluate their behaviour on heating by ex situ X-Ray Powder Diffraction and to observe the final clinker morphology by Scanning Electron Microscopy. Results indicate the calcite microstrain is a reliable parameter to predict the burnability of the raw meals, in terms of calcium silicates growth and lime consumption. In particular, mixtures prepared starting from high-strained calcite exhibit a better burnability. Later, when the melt appears this correlation vanishes; however differences in the early burnability still reflect on the final clinker composition and texture.

  9. An experimental study on the primary fragmentation and attrition of limestones in a fluidized bed

    International Nuclear Information System (INIS)

    Yao, Xuan; Zhang, Hai; Yang, Hairui; Liu, Qing; Wang, Jinwei; Yue, Guangxi

    2010-01-01

    In this paper, an experimental study on the primary fragmentation and attrition of 5 limestones in a fluidized bed was conducted. The intensity of fragmentation and attrition were measured in the same apparatus but at different fluidizing velocities. It was found that the averaged size of the particles decreased by about 10-20% during the fragmentation process. The important factors for particle comminution include limestone types, heating rate, calcination condition and ambient CO 2 concentration. Fragmentation mainly occurred in the first a few minutes in the fluidized bed and it was more intense than that in the muffle furnace at the same temperature. The original size effect was ambiguous, depending on the limestone type. The comminution caused by attrition mainly occurred during calcination process rather than sulphation process. The sulphation process was fragmentation and attrition resisted. The attrition rate of sulphate was similar to that of lime in trend, decaying exponentially with time, but was one-magnitude-order smaller than that of lime. Present experimental results indicate that fragmentation mechanism of the limestone is dominated by CO 2 release instead of thermal stress. (author)

  10. Piedramuelle Limestone in the building heritage of Oviedo, Spain, and adjacent towns.

    Science.gov (United States)

    Cardenes Van den Eynde, Victor; Mateos, Felix Javier; Valdeon, Luis; Rojo, Araceli

    2017-04-01

    The Piedramuelle limestone has a very important representation in the building heritage of Oviedo, historical capital of Asturias (Spain) and surrounding towns. This argillaceous limestone has been quarried since the High Middle Ages until the beginning of the XX century. The main mineralogical components are carbonates (mainly calcite and sometimes ankerite, 70-90%), quartz (5-15%), terrigenous minerals (6-15%) and iron oxides (blocks and ashlars of the buildings. Some of the buildings constructed with Piedramuelle limestone are the Cathedral, the Old University and the Palaces from the XVII and XVIII centuries. The ambiance and historical architecture of Oviedo and adjacent towns is closely linked with the textures and colors of this stone. Nowadays, the Piedramuelle limestone is not exploited anymore, being the quarries exhausted. This represents an issue from a conservation point of view, since there is not a suitable stone for replacement. In order to preserve and maintain the building heritage of these towns, it is very important to prospect and protect the remaining outcrops still able to supply this characteristic stone.

  11. Thermal effects induced by laser ablation in non-homogeneous limestone covered by an impurity layer

    Science.gov (United States)

    Cocean, Alexandru; Pelin, Vasile; Cazacu, Marius Mihai; Cocean, Iuliana; Sandu, Ion; Gurlui, Silviu; Iacomi, Felicia

    2017-12-01

    This paper reports preliminary results concerning thermal effects induced by urban/industrial air pollutants deposited on a limestone rock when heated by pulsed laser in the cleaning process. The process of laser cleaning treatment of the crust is simulated using COMSOL Multiphysics 4.4, finite element analysis software. Scanning Electron Microscopy coupled with Energy Dispersive X-ray Spectroscopy and Laser Induced Breakdown Spectroscopy techniques have been used to analyze the chemical composition of the samples. Two elements found as being present into the dust and in the crust, such as iron and magnesium particles are used for simulation in COMSOL. Therefore, the profiles heat evolutions on the crust surface and inside limestone are obtained as thermal interactions between the three components (iron, magnesium and limestone), simulating the non-homogeneous materials. It has been observed that iron impurities caused by the dust deposition may damage the limestone through a process of overheating, as a consequence of a high thermal conduction phenomenon, recorded for the region with iron impurities and sizes of micrometric order are localized. The thermal contact between the three components results in plots that reflect their thermal interactions.

  12. Radiological significance of Egyptian limestone and alabaster used for construction of dwellings

    International Nuclear Information System (INIS)

    El-Taher, A.; Makhluf, V.

    2011-01-01

    The natural radionuclides in limestone and alabaster found in Assuit Governorate in Upper Egypt have been investigated by passive gamma-ray spectrometry. From the measured γ-ray spectra, specific activities were determined. The measured activity concentrations for these natural radionuclides were compared with the reported data from other countries. The radiation hazard parameters related to the exposure of limestone and alabaster have also been calculated. The obtained results of radium equivalent Raeq, level index Iγr, the external hazard index H ex and absorbed dose rate in limestone (90.44, 0.63, 0.17, 39.94) and (70.86, 0.50, 0.13, 31.55) are lower than the acceptable level 370 Bqkg -1 for radium equivalent Ra eq , 1 for level index Iγr, the external hazard index H e≤ I and 59 (nGy.h -1 ) for absorbed dose rate. So limestone and alabaster can be used as building construction without exceeding the proposed radioactivity criterion level. (author)

  13. 230Th/234U dating of coral limestones and vertical uplift at Djibouti

    International Nuclear Information System (INIS)

    Faure, Hugues; Hoang, C.T.; Lalou, Claude

    1980-01-01

    Coral limestones sampled from marine terraces along the Afar coast have been dated by the 230 Th/ 234 U method. The ages confirm the stratigraphic unity of these formations and the existence of the paleo sea level dated 124 000 years ago in this region. These results permit to deduce the uplift rates of this littoral [fr

  14. Treatment Of Metal-Mine Effluents By Limestone Neutralization And Calcite Co-Precipitation

    Science.gov (United States)

    The U.S. Geological Survey - Leetown Science Center and the Colorado School of Mines have developed a remediation process for the treatment of metals in circumneutral mining influenced waters. The process involves treatment with a pulsed limestone bed (PLB) system, followed by c...

  15. Treatment Of Metal-Mine Effluents By Limestone Neutralization And Calcite Co-Precipitation (Presentation)

    Science.gov (United States)

    The U.S. Geological Survey - Leetown Science Center and the Colorado School of Mines have developed a remediation process for the treatment of metals in circumneutral mining influenced waters. The process involves treatment with a pulsed limestone bed (PLB) system, followed by c...

  16. Limestone amendments and the establishment of legumes on pyritic colliery spoil

    Energy Technology Data Exchange (ETDEWEB)

    Jefferies, R A

    1981-11-01

    This paper examines the effect of high liming, using two commercially available limestone grades of different particle size distributions, on the establishment of six contrasting legume species, in order to determine whether other legume species are more tolerant of the conditions imposed by high liming, and whether the effect can be avoided. 13 refs.

  17. Autogenous and drying shrinkage of sodium carbonate activated slag altered by limestone powder incorporation

    NARCIS (Netherlands)

    Yuan, B.; Yu, Q.L.; Dainese, E.; Brouwers, H.J.H.

    2017-01-01

    This paper aims to study the shrinkage mechanism of sodium carbonate activated slag containing limestone powder (LP). The workability, pore structure, reaction kinetics and strength development were characterized. The results show that the autogenous shrinkage increases when the dosage of LP is low

  18. Assessing the chemical involvement of limestone powder in sodium carbonate activated slag

    NARCIS (Netherlands)

    Yuan, B.; Yu, Q.; Brouwers, H.J.H.

    2017-01-01

    This study aims to investigate the effect of limestone powder (LP) on the reaction of sodium carbonate activated slag. The results show that the incorporated LP up to 30% improves the strength development, especially at advanced curing ages. A slightly accelerated reaction is observed for samples

  19. Influence of limestone powder on the reaction kinetics and mechanical properties of sodium carbonate activated slag

    NARCIS (Netherlands)

    Yuan, B.; Yu, Q.; Brouwers, H.J.H.

    2016-01-01

    The effects of limestone powder (LP) on the performance of Portland cement based composites have been extensively studied, considering that LP not only acts as nuclei sites, but that it is also chemically involved in the hydration process, which improves the reaction degree at the early age. In high

  20. Transient Catalytic Activity of Calcined Dolomitic Limestone in a Fluidized Bed during Gasification of Woody Biomass.

    Czech Academy of Sciences Publication Activity Database

    Pohořelý, Michael; Jeremiáš, Michal; Skoblia, S.; Beňo, Z.; Šyc, Michal; Svoboda, Karel

    2016-01-01

    Roč. 30, č. 5 (2016), s. 4065-4071 ISSN 0887-0624 R&D Projects: GA ČR GC14-09692J Institutional support: RVO:67985858 Keywords : fluidized- bed gasification * woody biomass * limestone Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 3.091, year: 2016

  1. Hydrobiogeochemical interactions in 'anoxic' limestone drains for neutralization of acidic mine drainage

    Science.gov (United States)

    Robbins, E.I.; Cravotta, C.A.; Savela, C.E.; Nord, G.L.

    1999-01-01

    Processes affecting neutralization of acidic coal mine drainage were evaluated within 'anoxic' limestone drains (ALDs). Influents had pH???3.5 and dissolved oxygen treatment step is indicated to promote Al removal before diverting acidic mine water into alkalinity-producing materials. ?? 1998 Elsevier Science Ltd.

  2. Extensive yellow crusts below limestone overhangs: a new taxon close to a minute epiphytic lichen

    Czech Academy of Sciences Publication Activity Database

    Vondrák, Jan; Moniri, M. H.; Malíček, Jiří; Košnar, J.

    2017-01-01

    Roč. 35, č. 3 (2017), s. 368-376 ISSN 0107-055X Institutional support: RVO:67985939 Keywords : Caloplaca substerilis * limestone rocks * Central Europe Subject RIV: EF - Botanics OBOR OECD: Plant sciences, botany Impact factor: 0.847, year: 2016

  3. Effect of Limestone Powder on Acid Attack Characteristics of Cement Pastes

    Directory of Open Access Journals (Sweden)

    Shuhua LIU

    2014-12-01

    Full Text Available The acid resistance of cement pastes containing limestone powder with two different water-binder (w/b ratios exposed to acetic (pH = 4 and sulfuric acid (pH = 2 solutions respectively were investigated in this paper. Limestone powder, fly ash and silica fume were also added to the cement paste mixture at different proportions. Static and flowing aqueous environments were set in this experiment. Strength and microstructure of the pastes after acid attack were investigated by using strength test, X-ray diffractometer (XRD and scanning electron microscopy (SEM. The experimental results show that the erosion degree depends not only on pH value of the solution and w/b ratio of the pastes, but also on the content of limestone powder. Acetic acid reacts with calcium hydroxide and carbonate thus dissolving the pastes, while sulfuric acid consumed calcium hydroxide, and generated gypsum and ettringite. The consumption of calcium hydroxide in the flowing solution group is higher than that in the static solution because the flowing sulfuric acid solution has negative effect upon the gypsum crystallization. Fly ash and silica fume are beneficial to limestone cement paste because of the less calcium hydroxide formation, which is among the hydrates vulnerable to acid erosion. DOI: http://dx.doi.org/10.5755/j01.ms.20.4.6231

  4. In Situ Generated Colloid Transport of Cu and Zn in Reclaimed Mine Soil Profiles Associated with Bio solids Application

    International Nuclear Information System (INIS)

    Miller, J.O.; Karathanasis, A.D.; Matocha, C.J.

    2011-01-01

    Areas reclaimed for agricultural uses following coal mining often receive bio solids applications to increase organic matter and fertility. Transport of heavy metals within these soils may be enhanced by the additional presence of bio solids colloids. Intact monoliths from reclaimed and undisturbed soils in Virginia and Kentucky were leached to observe Cu and Zn mobility with and without bio solids application. Transport of Cu and Zn was observed in both solution and colloid associated phases in reclaimed and undisturbed forest soils, where the presence of unweathered spoil material and bio solids amendments contributed to higher metal release in solution fractions. Up to 81% of mobile Cu was associated with the colloid fraction, particularly when gabbiest was present, while only up to 18% of mobile Zn was associated with the colloid fraction. The colloid bound Cu was exchangeable by ammonium acetate, suggesting that it will release into groundwater resources.

  5. In Situ Generated Colloid Transport of Cu and Zn in Reclaimed Mine Soil Profiles Associated with Bio solids Application

    International Nuclear Information System (INIS)

    Miller, J.O.; Karathanasis, A.D.; Matocha, C.J.

    2011-01-01

    Areas reclaimed for agricultural uses following coal mining often receive bio solids applications to increase organic matter and fertility. Transport of heavy metals within these soils may be enhanced by the additional presence of bio solids colloids. Intact monoliths from reclaimed and undisturbed soils in Virginia and Kentucky were leached to observe Cu and Zn mobility with and without bio solids application. Transport of Cu and Zn was observed in both solution and colloid associated phases in reclaimed and undisturbed forest soils, where the presence of unweathered spoil material and bio solids amendments contributed to higher metal release in solution fractions. Up to 81% of mobile Cu was associated with the colloid fraction, particularly when gibbsite was present, while only up to 18% of mobile Zn was associated with the colloid fraction. The colloid bound Cu was exchangeable by ammonium acetate, suggesting that it will release into groundwater resources.

  6. Foulant characteristics comparison in recycling cooling water system makeup by municipal reclaimed water and surface water in power plant.

    Science.gov (United States)

    Ping, Xu; Jing, Wang; Yajun, Zhang; Jie, Wang; Shuai, Si

    2015-01-01

    Due to water shortage, municipal reclaimed water rather than surface water was replenished into recycling cooling water system in power plants in some cities in China. In order to understand the effects of the measure on carbon steel corrosion, characteristics of two kinds of foulant produced in different systems were studied in the paper. Differences between municipal reclaimed water and surface water were analyzed firstly. Then, the weight and the morphology of two kinds of foulant were compared. Moreover, other characteristics including the total number of bacteria, sulfate reducing bacteria, iron bacteria, extracellular polymeric substance (EPS), protein (PN), and polysaccharide (PS) in foulant were analyzed. Based on results, it could be concluded that microbial and corrosive risk would be increased when the system replenished by municipal reclaimed water instead of surface water.

  7. Limestone and Zeolite as Alternative Media in Horizontal Subsurface Flow Constructed Wetlands: Laboratory-Scale Studies

    Science.gov (United States)

    Lizama, K.; Jaque, I.; Ayala, J.

    2016-12-01

    Arsenic is well known for its chronic toxicity. Millions of people around the world are currently at risk, drinking water with As concentrations above 10 ppb, the WHO drinking water guideline. Although different treatment options exist, they are often limited by elevated costs and maintenance requirements. Constructed wetlands are a natural water treatment system, capable to remove metals and metalloids -including As- via different physical, chemical and biological processes. The use of alternative supporting media to enhance As removal in subsurface flow wetlands has been recommended, but not sufficiently studied. Limestone and zeolite have been identified as effective supporting media in subsurface flow wetlands aiming As removal. However, there are still key aspects to be addressed, such as the implications of using these media, the speciation in the solid phase, the role of vegetation, etc. This study investigated the performance of limestone and zeolite in three types of experiments: batch, column and as main supporting media in a bench scale horizontal subsurface flow wetland system. Synthetic water resembling a contaminated river in Chile (As concentration=3 mg/L, Fe concentration= 100 mg/L, pH=2) was used in all experiments. In the batch experiments, the As concentration, the mass of media and the contact time were varied. The column system consisted of three limestone columns and three zeolite columns, operated under a hydraulic loading of 20 mm/d. The wetland system consisted of twelve PVC cells: six filled with zeolite and six with limestone. Phragmites australis were planted in three cells of each media type, as control cells. From the batch experiments, maximum As sorption capacities as indicated by Langmuir model were 1.3 mg/g for limestone and 0.17 mg/g for zeolite, at 18 h contact time and 6.3 g/L medium concentration. EDS and XPS analyses revealed that As and Fe were retained in zeolite at the end of the batch experiments. Zeolite and limestone

  8. Soil macropores: Control on infiltration, hillslope and surface hydrology on a reclaimed surface-mined watershed

    International Nuclear Information System (INIS)

    Guebert, M.D.; Gardner, T.W.

    1992-01-01

    The hydrologic response of a surface-mined watershed in central Pennsylvania is controlled by rapid macropore flow within the unsaturated man-made topsoil. Newly reclaimed surface-mined watersheds in central Pennsylvania exhibit low steady-state infiltration rates (1--2 cm/hr) and produce runoff dominated by infiltration-excess overland flow. However, within four years after reclamation, infiltration rates on some mine surfaces approach premined rates (8 cm/hr). As infiltration rate increases, the volume of infiltrated water increases, but the total porosity of minesoil matrix remains constant. There is little change in the surface discharge volume, indicating that infiltrated water continues to contribute to the basin surface discharge by the processes of throughflow and return flow. Throughflow in the topsoil horizon occurs in rapid response to rainfall input, producing large volumes of water with throughflow rates closely related to rainfall rates and with throughflow peaks following rainfall peaks by only minutes. Increased return flow alters the shape of the surface runoff hydrograph by slightly lagging behind infiltration excess overland flow. These changes in the shape of the surface runoff hydrograph reduce the potential for severe gully erosion on the reclaimed site. In addition, throughflow water remains predominantly in the topsoil horizon, and therefore has limited contact with potentially acid-producing backfill. Better understanding of macropore flow processes in reclaimed minesoils will help investigators evaluate past strategies and develop new reclamation techniques that will minimize the short-term surface erosional effects of mining and reclamation, while optimizing the long-term effluent and groundwater quality

  9. Reclaimed water as a reservoir of antibiotic resistance genes: distribution system and irrigation implications

    Directory of Open Access Journals (Sweden)

    Nicole L Fahrenfeld

    2013-05-01

    Full Text Available Treated wastewater is increasingly being reused to achieve sustainable water management in arid regions. The objective of this study was to quantify the distribution of antibiotic resistance genes (ARGs in recycled water, particularly after it has passed through the distribution system, and to consider point-of-use implications for soil irrigation. Three separate reclaimed wastewater distribution systems in the western U.S. were examined. Quantitative polymerase chain reaction (qPCR was used to quantify ARGs corresponding to resistance to sulfonamides (sul1, sul2, macrolides (ermF, tetracycline (tet(A, tet(O, glycopeptides (vanA, and methicillin (mecA, in addition to genes present in waterborne pathogens Legionella pneumophila (Lmip, Escherichia coli (gadAB, and Pseudomonas aeruginosa (ecfx, gyrB. In a parallel lab study, the effect of irrigating an agricultural soil with secondary, chlorinated, or dechlorinated wastewater effluent was examined in batch microcosms. A broader range of ARGs were detected after the reclaimed water passed through the distribution systems, highlighting the importance of considering bacterial re-growth and the overall water quality at the point of use. Screening for pathogens with qPCR indicated presence of Lmip and gadAB genes, but not ecfx or gyrB. In the lab study, chlorination was observed to reduce 16S rRNA and sul2 gene copies in the wastewater effluent, while dechlorination had no apparent effect. ARGs levels did not change with time in soil slurries incubated after a single irrigation event with any of the effluents. However, when irrigated repeatedly with secondary wastewater effluent (not chlorinated or dechlorinated, elevated levels of sul1 and sul2 were observed. This study suggests that reclaimed water may be an important reservoir of ARGs, especially at the point of use, and that attention should be directed towards the fate of ARGs in irrigation water and the implications for human health.

  10. Uptake and distribution of bisphenol A and nonylphenol in vegetable crops irrigated with reclaimed water.

    Science.gov (United States)

    Lu, Jian; Wu, Jun; Stoffella, Peter J; Wilson, P Chris

    2015-01-01

    The potential uptake and distribution of bisphenol A (BPA) and nonylphenol (NP) (from reclaimed irrigation water) in edible crops was investigated. BPA and NP were spiked into simulated reclaimed water at environmentally relevant concentrations. Two crops (lettuce, Lactuca sativa and tomato, Lycopersicon esculentum) were grown hydroponically in a greenhouse using the spiked irrigation water under two irrigation exposure scenarios (overhead foliar exposure and subsurface root exposure). BPA concentrations in tomato fruit were 26.6 ± 5.8 (root exposure) and 18.3 ± 3.5 (foliar exposure) μg kg(-1), while concentrations in lettuce leaves were 80.6 ± 23.1 (root exposure) and 128.9 ± 17.4 (foliar exposure) μg kg(-1). NP concentrations in tomato fruit were 46.1 ± 6.6 (root exposure) and 24.6 ± 6.4 (foliar exposure) μg kg(-1), while concentrations in lettuce leaves were 144.1 ± 9.2 (root exposure) and 195.0 ± 16.9 (foliar exposure) μg kg(-1). BPA was relatively mobile in lettuce plants regardless of exposure route. Limited mobility was observed for NP in both crops and BPA in tomatoes. The estimated daily intake of BPA and NP through consumption of vegetables irrigated with reclaimed water ranged from 8.9-62.9 to 11.9-95.1 μg, respectively, depending on the exposure route. Copyright © 2014 Elsevier B.V. All rights reserved.

  11. Allegheny woodrat (Neotoma magister) use of rock drainage channels on reclaimed mines in southern West Virginia

    Science.gov (United States)

    Chamblin, H.D.; Wood, P.B.; Edwards, J.W.

    2004-01-01

    Allegheny woodrats (Neotoma magister) currently receive protected status throughout their range due to population declines. Threats associated with habitat fragmentation (e.g., introduced predators, disease, loss of connectivity among subpopulations and habitat loss) may explain why Allegheny woodrats are no longer found in many areas where they existed just 25 y ago. In southern West Virginia, surface coal mining is a major cause of forest fragmentation. Furthermore, mountaintop mining, the prevalent method in the region, results in a loss of rock outcrops and cliffs within forested areas, typical habitat of the Allegheny woodrat To determine the extent that Allegheny woodrats make use of reclaimed mine land, particularly rock drainages built during reclamation, we sampled 24 drainage channels on reclaimed surface mines in southern West Virginia, collected habitat data at each site and used logistic regression to identify habitat variables related to Allegheny woodrat presence. During 187 trap nights, 13 adult, 2 subadult and 8 juvenile Allegheny woodrats were captured at 13 of the 24 sites. Percent of rock as a groundcover and density of stems >15 cm diameter-at-breast-height (DBH) were related to Allegheny woodrat presence and were significantly greater at sites where Allegheny woodrats were present than absent. Sites where Allegheny woodrats were present differed substantially from other described habitats in West Virginia, though they may simulate boulder piles that occur naturally. Our findings suggest the need for additional research to examine the dynamics between Allegheny woodrat populations inhabiting rock outcrops in forests adjacent to mines and populations inhabiting constructed drainage channels on reclaimed mines. However, if Allegheny woodrats can use human-created habitat, our results will be useful to surface mine reclamation and to other mitigation efforts where rocky habitats are lost or disturbed.

  12. Biological Reclaiming of Recycled Rubber and Its Effect on Mechanical Properties of New Rubber Vulcanizates

    Directory of Open Access Journals (Sweden)

    Maryam Mansourirad

    2014-12-01

    Full Text Available Nowadays, due to environmental concerns, there has been great attention to recycling and reclaiming of tires. Different methods have been used for reclaiming or desulfurization of rubber. One of these methods, in which desulfurization of rubber happens with no damage to the polymer structure, is desulfurization by biological microorganisms. In this research the application and performance of thermophilic and sulfur oxidizing bacteria, Acidianus brierleyi for this purpose was investigated. Ground tire rubber was detoxified with organic solvents, and the optimum conditions for growing microorganisms in the existence of rubber powder in the shaker flasks were determined. In order to accelerate the process, the suitable conditions for growth of bacteria and desulfurization in the bioreactor were adopted. Fourier transfer infrared spectroscopy and scanning electron microscopy were employed to characterize desulfurization of bio-treated powder from bioreactor. The results indicated that morphological changes on powder surface and reduction of sulfur bonds have occurred. Samples from bioreactors, with and without bacteria and also untreated rubber powder were compounded with virgin styrene butadiene rubber. Tensile and dynamic properties were investigated using uni-direction tensile test and dynamic-mechanical-thermal analysis, respectively. Although some differences in dynamic-mechanical-thermal properties of samples pointed to stronger interaction between rubber matrix and treated rubber powder, no significant improvements in the mechanical properties of vulcanizates containing A.brierleyi-treated powder were observed. Low concentration of sulfur in rubber vulcanizates, chemical bonds of sulfur, and low efficiency of A. brierleyi in breaking sulfur bonds and reclaiming rubber were considered as the reasons for low efficiency of this treatment process.

  13. The Öland limestone - A Swedish stone used for more than one thousand years

    Science.gov (United States)

    Schouenborg, Björn; Wickström, Linda; Mikaelsson, Jan

    2016-04-01

    The second largest island in Sweden is the home of the "Öland limestone", a condensed and bedded limestone whose origin dates back to Lower Ordovician, i.e. about 480 M years ago. Öland is a part of the palaeocontinent Baltica that, at the time, was situated at low latitudes with deposition of the calcareous sediments in a cool water environment. The limestone on Öland represents a proximal ramp tectonic setting, with the oldest sediments deposited in the west and younger sediments deposited towards east and southeast. Fluctuating sea-levels have created erosional hard grounds such as the Flowery sheet. These hardgrounds are recognised by their vivid colours and trace fossils, and can be traced all over Baltica, but is maybe best represented on Öland. Ordovician limestones are present in many places in Sweden, but it is the occurrence on Öland that is the most renowned in a building stone perspective. One reason for this is the favourable trading location, an island off the Swedish East coast in middle of the trading routes between the Baltic countries and the continent. Other reasons are the pleasant aesthetical values with numerous orthoceratites and other fossils. The limestones on Öland differ in colour. From the red varieties (with oxidized iron) to brownish and grey. The bedding is mostly in the cm-scale which easily enables very exploitable thickness of slabs. Every mm limestone represents about 1000 years of deposition. The limestone has most likely been used in a very crude way for many thousand years, but archaeological evidence of a more industrialized usage is just a little more than 1000 years. It is known from the literature that the first official Swedish king, Gustav Vasa (16th century), desired this stone. At the time it was called "Öland marble", and the king "imported" specialists to process it further at the Royal Stone workshop on northern Öland. Remnants of tools and working sites still remain in an outdoor museum. Export of the

  14. Morphological Changes of Limestone Sorbent Particles during Carbonation/Calcination Looping Cycles in a Thermogravimetric Analyzer (TGA) and Reactivation with Steam

    KAUST Repository

    Wu, Y.; Blamey, J.; Anthony, E. J.; Fennell, P. S.

    2010-01-01

    Carbonation and calcination looping cycles were carried out on four limestones in a thermogravimetric analyzer (TGA). The CO2 carrying capacity of a limestone particle decays very quickly in the first 10 cycles, reducing to about 20% of its original

  15. Chlorinated and ultraviolet radiation -treated reclaimed irrigation water is the source of Aeromonas found in vegetables used for human consumption

    Energy Technology Data Exchange (ETDEWEB)

    Latif-Eugenín, Fadua; Beaz-Hidalgo, Roxana; Silvera-Simón, Carolina [Unidad de Microbiología, Facultad de Medicina y Ciencias de la Salud, IISPV, Universidad Rovira i Virgili, Reus (Spain); Fernandez-Cassi, Xavi [Departamento de Microbiología, Facultad de Biología, Universidad de Barcelona, Barcelona (Spain); Figueras, María J., E-mail: mariajose.figueras@urv.cat [Unidad de Microbiología, Facultad de Medicina y Ciencias de la Salud, IISPV, Universidad Rovira i Virgili, Reus (Spain)

    2017-04-15

    Wastewater is increasingly being recognized as a key water resource, and reclaimed water (or treated wastewater) is used for irrigating vegetables destined for human consumption. The aim of the present study was to determine the diversity and prevalence of Aeromonas spp. both in reclaimed water used for irrigation and in the three types of vegetables irrigated with that water. Seven of the 11 (63.6%) samples of reclaimed water and all samples of vegetables were positive for the presence of Aeromonas. A total of 216 Aeromonas isolates were genotyped and corresponded to 132 different strains that after identification by sequencing the rpoD gene belonged to 10 different species. The prevalence of the species varied depending on the type of sample. In the secondary treated reclaimed water A. caviae and A. media dominated (91.4%) while A. salmonicida, A. media, A. allosaccharophila and A. popoffii represented 74.0% of the strains in the irrigation water. In vegetables, A. caviae (75.0%) was the most common species, among which a strain isolated from lettuce had the same genotype (ERIC pattern) as a strain recovered from the irrigation water. Furthermore, the same genotype of the species A. sanarellii was recovered from parsley and tomatoes demonstrating that irrigation water was the source of contamination and confirming the risk for public health. - Highlights: • Reclaimed water (= treated wastewater) is used for the irrigation of vegetables. • Aeromonas was found in reclaimed water and irrigated vegetables with this water. • The prevalence of Aeromonas spp. varied between irrigation water and vegetables. • Epidemiological relationships were found between irrigation water and vegetables. • The water was the source of contamination which means a risk for the public health.

  16. Chlorinated and ultraviolet radiation -treated reclaimed irrigation water is the source of Aeromonas found in vegetables used for human consumption

    International Nuclear Information System (INIS)

    Latif-Eugenín, Fadua; Beaz-Hidalgo, Roxana; Silvera-Simón, Carolina; Fernandez-Cassi, Xavi; Figueras, María J.

    2017-01-01

    Wastewater is increasingly being recognized as a key water resource, and reclaimed water (or treated wastewater) is used for irrigating vegetables destined for human consumption. The aim of the present study was to determine the diversity and prevalence of Aeromonas spp. both in reclaimed water used for irrigation and in the three types of vegetables irrigated with that water. Seven of the 11 (63.6%) samples of reclaimed water and all samples of vegetables were positive for the presence of Aeromonas. A total of 216 Aeromonas isolates were genotyped and corresponded to 132 different strains that after identification by sequencing the rpoD gene belonged to 10 different species. The prevalence of the species varied depending on the type of sample. In the secondary treated reclaimed water A. caviae and A. media dominated (91.4%) while A. salmonicida, A. media, A. allosaccharophila and A. popoffii represented 74.0% of the strains in the irrigation water. In vegetables, A. caviae (75.0%) was the most common species, among which a strain isolated from lettuce had the same genotype (ERIC pattern) as a strain recovered from the irrigation water. Furthermore, the same genotype of the species A. sanarellii was recovered from parsley and tomatoes demonstrating that irrigation water was the source of contamination and confirming the risk for public health. - Highlights: • Reclaimed water (= treated wastewater) is used for the irrigation of vegetables. • Aeromonas was found in reclaimed water and irrigated vegetables with this water. • The prevalence of Aeromonas spp. varied between irrigation water and vegetables. • Epidemiological relationships were found between irrigation water and vegetables. • The water was the source of contamination which means a risk for the public health.

  17. The Use of Amine Reclaimer Wastes as a NOx Reduction Agent

    DEFF Research Database (Denmark)

    Botheju, Deshai; Glarborg, Peter; Tokheim, Lars-Andre

    2013-01-01

    that of aqueous ammonia, i.e. the most common SNCR chemical reagent used in industry (above 60% NOx reduction efficiency), ARW is nonetheless shown to possess valuable SNCR qualities (at least 20% NOx reduction efficiency) considering its availability as a waste product which has to be safely disposed. A series...... of thermo-gravimetric analyses provided important information on vaporization characteristics of amine reclaimer bottom wastes. The proposed methodology can lead to simultaneous energy and material resource recovery while primarily solving two environmental pollution problems, i.e. toxic ARW wastes...

  18. Development of a new methodology for mitigating acid mine drainage (AMD) at reclaimed surface mines

    International Nuclear Information System (INIS)

    Ackman, T.E.; Kim, A.G.

    1993-01-01

    A 1.2 hectare (ha) experimental site located on a 14.5 ha reclaimed surface mine in Greene County, PA was injected with a 141 cubic meters (m 3 ) of fly ash and fluidized bed combustion (FBC) ash grout that included acid mine drainage (AMD) sludge. An evaluation of this AMD abatement approach by the Bureau of Mines found that the average net acidity and concentrations of several metal ions at the discharge seep and monitoring wells decreased after grouting. Changes in metal concentrations were assumed to be related to alkaline addition and/or encapsulation. Initial results indicate that this technique is potentially an effective AMD abatement method

  19. Geological Sequestration of CO2 by Hydrous Carbonate Formation with Reclaimed Slag

    Energy Technology Data Exchange (ETDEWEB)

    Von L. Richards; Kent Peaslee; Jeffrey Smith

    2008-02-06

    The concept of this project is to develop a process that improves the kinetics of the hydrous carbonate formation reaction enabling steelmakers to directly remove CO2 from their furnace exhaust gas. It is proposed to bring the furnace exhaust stream containing CO2 in contact with reclaimed steelmaking slag in a reactor that has an environment near the unit activity of water resulting in the production of carbonates. The CO2 emissions from the plant would be reduced by the amount sequestered in the formation of carbonates. The main raw materials for the process are furnace exhaust gases and specially prepared slag.

  20. Soil degradation under reclaimed wastewater in arenados (Lanzarote, Canary Islands, Spain)

    Energy Technology Data Exchange (ETDEWEB)

    Tejedor, M.; Jimenez, C.; Hernandez-Moreno, J. M.; Diaz, F.

    2009-07-01

    In the Island of Lanzarote, one of the most arid zones of the EU, a traditional farming system based on the soil mulching with basaltic tephra, locally known as arenados, was developed since the 18th century. This dry-framing system accounts currently for more than 21% of the island surface. However, in the last decades, this system has been transformed with the incorporation of irrigation, due to the availability of new non-conventional water resources (desalinised and reclaimed municipal wastewater). (Author)

  1. Soil degradation under reclaimed wastewater in arenados (Lanzarote, Canary Islands, Spain)

    International Nuclear Information System (INIS)

    Tejedor, M.; Jimenez, C.; Hernandez-Moreno, J. M.; Diaz, F.

    2009-01-01

    In the Island of Lanzarote, one of the most arid zones of the EU, a traditional farming system based on the soil mulching with basaltic tephra, locally known as arenados, was developed since the 18th century. This dry-framing system accounts currently for more than 21% of the island surface. However, in the last decades, this system has been transformed with the incorporation of irrigation, due to the availability of new non-conventional water resources (desalinised and reclaimed municipal wastewater). (Author)

  2. Comparison of Limestone and Ground Fish for Treatment of Nutritional Rickets in Children in Nigeria.

    Science.gov (United States)

    Thacher, Tom D; Bommersbach, Tanner J; Pettifor, John M; Isichei, Christian O; Fischer, Philip R

    2015-07-01

    To determine whether children with calcium-deficiency rickets respond better to treatment with calcium as limestone or as ground fish. Nigerian children with active rickets (n = 96) were randomized to receive calcium as powdered limestone (920 mg of elemental calcium) or ground fish (952 mg of elemental calcium) daily for 24 weeks. Radiographic healing was defined as achieving a score of 1.5 or less on a 10-point scale. The median (range) age of enrolled children was 35 (6-151) months. Of the 88 children who completed the study, 29 (66%) in the ground fish group and 24 (55%) in the limestone group achieved the primary outcome of a radiographic score of 1.5 or less within 6 months (P = .39). The mean radiographic score improved from 6.2 ± 2.4 to 1.8 ± 2.2 in the ground fish group and from 6.3 ± 2.2 to 2.1 ± 2.4 in the limestone group (P = .68 for group comparison). In an intention to treat analysis adjusted for baseline radiographic score, age, milk calcium intake, and serum 25-hydroxyvitamin D concentration, the response to treatment did not differ between the 2 groups (P = .39). Younger age was associated with more complete radiographic healing in the adjusted model (aOR 0.74 [95% CI 0.57-0.92]). After 24 weeks of treatment, serum alkaline phosphatase had decreased, calcium and 25-hydroxyvitamin D increased, and bone mineral density increased in both groups, without significant differences between treatment groups. In children with calcium-deficiency rickets, treatment with calcium as either ground fish or limestone for 6 months healed rickets in the majority of children. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

  3. Evaluation of Different Modeling Approaches to Simulate Contaminant Transport in a Fractured Limestone Aquifer

    Science.gov (United States)

    Mosthaf, K.; Rosenberg, L.; Balbarini, N.; Broholm, M. M.; Bjerg, P. L.; Binning, P. J.

    2014-12-01

    It is important to understand the fate and transport of contaminants in limestone aquifers because they are a major drinking water resource. This is challenging because they are highly heterogeneous; with micro-porous grains, flint inclusions, and being heavily fractured. Several modeling approaches have been developed to describe contaminant transport in fractured media, such as the discrete fracture (with various fracture geometries), equivalent porous media (with and without anisotropy), and dual porosity models. However, these modeling concepts are not well tested for limestone geologies. Given available field data and model purpose, this paper therefore aims to develop, examine and compare modeling approaches for transport of contaminants in fractured limestone aquifers. The model comparison was conducted for a contaminated site in Denmark, where a plume of a dissolved contaminant (PCE) has migrated through a fractured limestone aquifer. Multilevel monitoring wells have been installed at the site and available data includes information on spill history, extent of contamination, geology and hydrogeology. To describe the geology and fracture network, data from borehole logs was combined with an analysis of heterogeneities and fractures from a nearby excavation (analog site). Methods for translating the geological information and fracture mapping into each of the model concepts were examined. Each model was compared with available field data, considering both model fit and measures of model suitability. An analysis of model parameter identifiability and sensitivity is presented. Results show that there is considerable difference between modeling approaches, and that it is important to identify the right one for the actual scale and model purpose. A challenge in the use of field data is the determination of relevant hydraulic properties and interpretation of aqueous and solid phase contaminant concentration sampling data. Traditional water sampling has a bias

  4. Influence of the Reclamation Process Intensity in the REGMAS Reclaimer on the Purification Degree of the High-silica Matrix

    Directory of Open Access Journals (Sweden)

    Skrzyński M.

    2016-03-01

    Full Text Available The investigation results of the reclamation of spent moulding sands with furfuryl resin are presented in this paper. The reclamation process was performed in the secondary reclamation chamber of the REGMAS 1.5 vibratory reclaimer. 70 kg portions of moulding sands, previously subjected to the primary reclamation and dedusting, were used. The secondary reclamation was performed in two stages: the first consisted of determining the reclaimer intensity at various reclamation times (5 min, 10 min and 15 min and various electrovibrator frequencies (40 Hz, 50 Hz and 60 Hz, the second consisted of determining the influence of additional crushing elements on the intensity of processes.

  5. Hydrogeology and simulation of the effects of reclaimed-water application in west Orange and southeast Lake counties, Florida

    Science.gov (United States)

    O'Reilly, Andrew M.

    1998-01-01

    Wastewater reclamation and reuse has become increasingly popular as water agencies search for alternative water-supply and wastewater-disposal options. Several governmental agencies in central Florida currently use the land-based application of reclaimed water (wastewater that has been treated beyond secondary treatment) as a management alternative to surface-water disposal of wastewater. Water Conserv II, a water reuse project developed jointly by Orange County and the City of Orlando, began operation in December 1986. In 1995, the Water Conserv II facility distributed approximately 28 Mgal/d of reclaimed water for discharge to rapid-infiltration basins (RIBs) and for use as agricultural irrigation. The Reedy Creek Improvement District (RCID) began operation of RIBs in September 1990, and in 1995 these RIBs received approximately 6.7 Mgal/d of reclaimed water. Analyses of existing data and data collected during the course of this study were combined with ground-water flow modeling and particle-tracking analyses to develop a process-oriented evaluation of the regional effects of reclaimed water applied by Water Conserv II and the RCID RIBs on the hydrology of west Orange and southeast Lake Counties. The ground-water flow system beneath the study area is a multi-aquifer system that consists of a thick sequence of highly permeable carbonate rocks overlain by unconsolidated sediments. The hydrogeologic units are the unconfined surficial aquifer system, the intermediate confining unit, and the confined Floridan aquifer system, which consists of two major permeable zones, the Upper and Lower Floridan aquifers, separated by the less permeable middle semiconfining unit. Flow in the surficial aquifer system is dominated regionally by diffuse downward leakage to the Floridan aquifer system and is affected locally by lateral flow systems produced by streams, lakes, and spatial variations in recharge. Ground water generally flows laterally through the Upper Floridan aquifer

  6. Water-quality data for two surface coal mines reclaimed with alkaline waste or urban sewage sludge, Clarion County, Pennsylvania, May 1983 through November 1989

    Science.gov (United States)

    Dugas, D.L.; Cravotta, C.A.; Saad, D.A.

    1993-01-01

    Water-quality and other hydrologic data for two surface coal mines in Clarion County, Pa., were collected during 1983-89 as part of studies conducted by the U.S. Geological Survey in cooperation with the Pennsylvania Department of Environmental Resources. Water samples were collected from streams, seeps, monitor wells, and lysimeters on a monthly basis to evaluate changes in water quality resulting from the addition of alkaline waste or urban sewage sludge to the reclaimed mine-spoil surface. The mines are about 3.5 miles apart and were mined for bituminous coal of the upper and lower Clarion seams of the Allegheny Group of Pennsylvanian age. The coal had high sulfur (greater than 2 weight percent) concentrations. Acidic mine drainage is present at both mines. At one mine, about 8 years after mining was completed, large quantities (greater than 400 tons per acre) of alkaline waste consisting of limestone and lime-kiln flue dust were applied on two 2.5-acre plots within the 65-acre mine area. Water-quality data for the alkaline-addition plots and surrounding area were collected for 1 year before and 3 years after application of the alkaline additives (May 1983-July 1987). Data collected for the alkaline-addition study include ground-water level, surface-water discharge rate, temperature, specific conductance, pH, and concentrations of alkalinity, acidity, sulfate, iron (total and ferrous), manganese, aluminum, calcium, and magnesium. At the other mine, about 3.5 years after mining was completed, urban sewage sludge was applied over 60 acres within the 150-acre mine area. Waterquality data for the sludge-addition study were collected for 3.5 years after the application of the sludge (June 1986-December 1989). Data collected for the sludge-addition study include the above constituents plus dissolved oxygen, redox potential (Eh), and concentrations of dissolved solids, phosphorus, nitrogen species, sulfide, chloride, silica, sodium, potassium, cyanide, arsenic, barium

  7. Rare earth element and strontium isotopic study of seamount-type limestones in Mesozoic accretionary complex of Southern Chichibu Terrane, central Japan. Implication for incorporation process of seawater REE into limestones

    International Nuclear Information System (INIS)

    Tanaka, Kazuya; Miura, Noriko; Asahara, Yoshihiro; Kawabe, Iwao

    2003-01-01

    Ishimaki and Tahara limestones occur as exotic blocks juxtaposed in the Mesozoic (Jurassic) accretionary complex of Southern Chichibu Terrane in eastern Aichi Prefecture, central Japan. They are supposed to be of the seamount-type limestone, since they have no terrigenous materials and are intimately associated with greenstones. REE (rare earth elements) and Sr isotopic studies for the limestones have been made in order to know their geochemical characteristics, ages and origins. Their 87 Sr/ 86 Sr ratios, when referred to the seawater 87 Sr/ 86 Sr curve and relevant geological data, suggest that Ishimaki and Tahara limestones are the late Permian and the Carboniferous to the Early Permian, respectively. Two greenstone fragments found inside the Ishimaki limestone block and one greenstone sample associated with Tahara limestone block, resemble the Hawaiian alkali basalt in the their REE and Y patterns. This is supporting the idea that the limestone blocks may be parts of reef limestones on ancient volcanic seamounts. All the limestone samples, except three unusual Tahara ones, show seawater REE and Y signatures in their chondrite-normalized patterns. Their REE/Ca ratios, however, are 10 2 -10 4 times as high as those ratios of modern biogenic carbonates like corals and the seawater. Accordingly, seawater REE and Y were incorporated into the limestones, when originally biogenic carbonates transformed into inorganic calcite and its secondary growths occurred in diagenesis in contact with sufficient seawater. This view is favored by the reported REE partition experiment between calcite overgrowths and seawater solution. The seawater Ce anomaly as a function of water depth in the modern ocean is a key to infer the water depth of the REE and Y incorporation. The Ce anomalies given by log (Ce/Ce*) for about a half of Ishimaki samples and most of Tahara ones are between -0.5 and -0.2, which are compatible with the shallow water origin. Another half of Ishimaki samples

  8. Groundwater monitoring of an open-pit limestone quarry: groundwater characteristics, evolution and their connections to rock slopes.

    Science.gov (United States)

    Eang, Khy Eam; Igarashi, Toshifumi; Fujinaga, Ryota; Kondo, Megumi; Tabelin, Carlito Baltazar

    2018-03-06

    Groundwater flow and its geochemical evolution in mines are important not only in the study of contaminant migration but also in the effective planning of excavation. The effects of groundwater on the stability of rock slopes and other mine constructions especially in limestone quarries are crucial because calcite, the major mineral component of limestone, is moderately soluble in water. In this study, evolution of groundwater in a limestone quarry located in Chichibu city was monitored to understand the geochemical processes occurring within the rock strata of the quarry and changes in the chemistry of groundwater, which suggests zones of deformations that may affect the stability of rock slopes. There are three distinct geological formations in the quarry: limestone layer, interbedded layer of limestone and slaty greenstone, and slaty greenstone layer as basement rock. Although the hydrochemical facies of all groundwater samples were Ca-HCO 3 type water, changes in the geochemical properties of groundwater from the three geological formations were observed. In particular, significant changes in the chemical properties of several groundwater samples along the interbedded layer were observed, which could be attributed to the mixing of groundwater from the limestone and slaty greenstone layers. On the rainy day, the concentrations of Ca 2+ and HCO 3 - in the groundwater fluctuated notably, and the groundwater flowing along the interbedded layer was dominated by groundwater from the limestone layer. These suggest that groundwater along the interbedded layer may affect the stability of rock slopes.

  9. Dynamic responses of photosystem II in the Namib Desert shrub, Zygophyllum prismatocarpum, during and after foliar deposition of limestone dust

    International Nuclear Information System (INIS)

    Heerden, P.D.R. van; Krueger, G.H.J.; Kilbourn Louw, M.

    2007-01-01

    The effects of limestone dust deposition on vegetation in desert ecosystems have not yet been reported. We investigated these effects in a succulent shrub from the Namib Desert at a limestone quarry near Skorpion Zinc mine (Namibia). Effects of limestone dust were determined in Zygophyllum prismatocarpum (dollar bush) plants with heavy, moderate and no visible foliar dust cover by means of chlorophyll a fluorescence measurements. Limestone dust deposition decreased overall plant performance through loss of chlorophyll content, inhibition of CO 2 assimilation, uncoupling of the oxygen-evolving complex and decreased electron transport. Importantly, dynamic recovery occurred after termination of limestone extraction at the quarry. Recovery was accelerated by rainfall, mainly because of dust removal from leaves and stimulation of new growth. These results indicate that limestone dust has severe effects on photosynthesis in desert shrubs, but that recovery is possible and that, in arid environments, this process is modulated by rainfall. - Limestone dust deposition reduced photosynthetic capacity in the Namib Desert shrub, Zygophyllum prismatocarpum

  10. Effects of dietary calcium levels and limestone particicle size on the performance, tibia and blood of laying hens

    Directory of Open Access Journals (Sweden)

    K Pelicia

    2011-03-01

    Full Text Available A total of 405 23-week-old ISA® Brown layers were distributed in a completely randomized experimental design in a factorial arrangement with nine treatments consisting of three dietary calcium levels (3.5, 3.75, and 4.5% and three limestone particle sizes (100% fine limestone (FL, 70% FL + 30% coarse limestone (CL and 50% (FL + 50% (CL, with nine replicates of five birds per cage. The following parameters were evaluated: percentage of lay, defective eggs, egg weight, egg mass, feed intake, feed conversion ratio (per kg eggs and per dozen eggs, and mortality. Dietary Ca levels significantly affected lay, with birds fed diets containing 4.5% calcium producing less eggs as compared to those fed 3.0 and 3.75% Ca. Egg production linearly decreased as dietary Ca levels increased, but blood Ca levels (mg/L increased in 28-week-old birds. The interaction of dietary Ca levels and limestone particle sizes resulted in a reduction in tibial ash Ca content as dietary Ca levels increased and as fine limestone was replaced by coarse limestone. It is concluded that a dietary Ca level of 3.75% and 100% fine particle limestone are required to maintain adequate egg production and available Ca blood level.

  11. Optimization and Thermoeconomics Research of a Large Reclaimed Water Source Heat Pump System

    Directory of Open Access Journals (Sweden)

    Zi-ping Zhang

    2013-01-01

    Full Text Available This work describes a large reclaimed water source heat pump system (RWSHPS and elaborates on the composition of the system and its design principles. According to the characteristics of the reclaimed water and taking into account the initial investment, the project is divided into two stages: the first stage adopts distributed heat pump heating system and the second adopts the combination of centralized and decentralized systems. We analyze the heating capacity of the RWSHPS, when the phase II project is completed, the system can provide hydronic heating water with the supply and return water temperature of 55°C/15°C and meet the hydronic heating demand of 8 million square meters of residential buildings. We make a thermal economics analysis by using Thermal Economics theory on RWSHPS and gas boiler system, it is known that the RWSHPS has more advantages, compared with the gas boiler heating system; both its thermal efficiency and economic efficiency are relatively high. It provides a reference for future applications of the RWSHPS.

  12. Predicted Infiltration for Sodic/Saline Soils from Reclaimed Coastal Areas: Sensitivity to Model Parameters

    Directory of Open Access Journals (Sweden)

    Dongdong Liu

    2014-01-01

    Full Text Available This study was conducted to assess the influences of soil surface conditions and initial soil water content on water movement in unsaturated sodic soils of reclaimed coastal areas. Data was collected from column experiments in which two soils from a Chinese coastal area reclaimed in 2007 (Soil A, saline and 1960 (Soil B, nonsaline were used, with bulk densities of 1.4 or 1.5 g/cm3. A 1D-infiltration model was created using a finite difference method and its sensitivity to hydraulic related parameters was tested. The model well simulated the measured data. The results revealed that soil compaction notably affected the water retention of both soils. Model simulations showed that increasing the ponded water depth had little effect on the infiltration process, since the increases in cumulative infiltration and wetting front advancement rate were small. However, the wetting front advancement rate increased and the cumulative infiltration decreased to a greater extent when θ0 was increased. Soil physical quality was described better by the S parameter than by the saturated hydraulic conductivity since the latter was also affected by the physical chemical effects on clay swelling occurring in the presence of different levels of electrolytes in the soil solutions of the two soils.

  13. Leaching risk of N-nitrosodimethylamine (NDMA) in soil receiving reclaimed wastewater.

    Science.gov (United States)

    Haruta, Shinsuke; Chen, Weiping; Gan, Jay; Simůnek, Jirka; Chang, Andrew C; Wu, Laosheng

    2008-03-01

    N-nitrosodimethylamine (NDMA) is a potential carcinogen frequently found in treated wastewater as a byproduct of chlorination. The potential for NDMA to contaminate the groundwater is a significant concern. A solute fate and transport model, Hydrus-1D, was used to evaluate the leaching potential of NDMA under different irrigation practices and soil properties. The results indicate that the risk of NDMA to reach the ground water is slim, when the reclaimed wastewater is applied under the customary conditions for landscape irrigation. The NDMA disappears in the reclaimed wastewater receiving soils rapidly through the microbial degradation and the volatilization processes. The factors that enhance the leaching risk are the soil hydraulic conductivity, the NDMA adsorption constants, and the irrigation intensity. When the hydraulic conductivity of soil is high, the NDMA adsorption constant of soil is low and/or the irrigation intensity is high, the NDMA leaching risk may dramatically increase. To reduce the NDMA leaching risk, it is imperative that the fields be irrigated at the proper volume and frequency and attention be paid to fields with soils having high-hydraulic conductivities and/or low-NDMA adsorption constants.

  14. Predicted infiltration for sodic/saline soils from reclaimed coastal areas: sensitivity to model parameters.

    Science.gov (United States)

    Liu, Dongdong; She, Dongli; Yu, Shuang'en; Shao, Guangcheng; Chen, Dan

    2014-01-01

    This study was conducted to assess the influences of soil surface conditions and initial soil water content on water movement in unsaturated sodic soils of reclaimed coastal areas. Data was collected from column experiments in which two soils from a Chinese coastal area reclaimed in 2007 (Soil A, saline) and 1960 (Soil B, nonsaline) were used, with bulk densities of 1.4 or 1.5 g/cm(3). A 1D-infiltration model was created using a finite difference method and its sensitivity to hydraulic related parameters was tested. The model well simulated the measured data. The results revealed that soil compaction notably affected the water retention of both soils. Model simulations showed that increasing the ponded water depth had little effect on the infiltration process, since the increases in cumulative infiltration and wetting front advancement rate were small. However, the wetting front advancement rate increased and the cumulative infiltration decreased to a greater extent when θ₀ was increased. Soil physical quality was described better by the S parameter than by the saturated hydraulic conductivity since the latter was also affected by the physical chemical effects on clay swelling occurring in the presence of different levels of electrolytes in the soil solutions of the two soils.

  15. Assessing metal pollution in ponds constructed for controlling runoff from reclaimed coal mines.

    Science.gov (United States)

    Miguel-Chinchilla, Leticia; González, Eduardo; Comín, Francisco A

    2014-08-01

    Constructing ponds to protect downstream ecosystems is a common practice in opencast coal mine reclamation. As these ponds remain integrated in the landscape, it is important to evaluate the extent of the effect of mine pollution on these ecosystems. However, this point has not been sufficiently addressed in the literature. The main objective of this work was to explore the metal pollution in man-made ponds constructed for runoff control in reclaimed opencast coal mines over time. To do so, we evaluated the concentration of ten heavy metals in the water, sediment, and Typha sp. in 16 runoff ponds ranging from 1 to 19 years old that were constructed in reclaimed opencast coal mines of northeastern Spain. To evaluate degree of mining pollution, we compared these data to those from a pit lake created in a local unreclaimed mine and to local streams as an unpolluted reference, as well as comparing toxicity levels in aquatic organisms. The runoff ponds showed toxic concentrations of Al, Cu, and Ni in the water and As and Ni in the sediment, which were maintained over time. Metal concentrations in runoff ponds were higher than in local streams, and macrophytes showed high metal concentrations. Nevertheless, metal concentrations in water and sediment in runoff ponds were lower than those in the pit lake. This study highlights the importance of mining reclamation to preserve the health of aquatic ecosystems and suggests the existence of chronic metal toxicity in the ponds, potentially jeopardizing pond ecological functions and services.

  16. [Effects of Different Reclaimed Scenarios on Soil Microbe and Enzyme Activities in Mining Areas].

    Science.gov (United States)

    Li, Jun-jian; Liu, Feng; Zhou, Xiao-mei

    2015-05-01

    Abstract: Ecological degradation in the mining areas is greatly aggravated in recent several decades, and ecological restoration has become the primary measure for the sustainable development. Soil microbe and enzyme activity are sensitive indices to evaluate soil quality. Ecological reconstruction was initiated in Antaibao mining area, and we tested soil physicochemical properties, microbial populations of azotobacteria, nitrifying-bacteria and denitrifying-bacteria, and enzyme activities (including sucrose, polyphenol oxidase, dehydrogenase and urease) under different regeneration scenarios. Regeneration scenarios had significant effects on soil physicochemical properties, microbial population and enzyme activities. Total nitrogen was strongly correlated with azotobacteria and nitrifying-bacteria, however, total nitrogen was not correlated with denitrifying-bacteria. Phenol oxidase activity was negatively correlated with soil organic carbon and total nitrogen, but other enzyme activities were positively correlated with soil organic carbon and total nitrogen. Principal Component Analysis ( PCA) was applied to analyze the integrated fertility index (IFI). The highest and lowest IFIs were in Robinia pseudoacacia-Pinus tabuliformis mixed forests and un-reclaimed area, respectively. R. pseudoacacia-P. tabuliformis mixed forests were feasible for reclaimed mining areas in semi-arid region Northwest Shanxi.

  17. Perch population assessment in lakes reclaimed using oil-sands derived material

    International Nuclear Information System (INIS)

    Heuvel, M.R. van den; Dixon, D.G.; Power, M.; Boerger, H.; MacKinnon, M.D.; Meer, T. van

    1995-01-01

    The mining and extraction of petroleum products from oil-sands involves large areas of land and produces enormous volumes of tailings. One possible land reclamation option is to incorporate fine-tailings material into the bottoms of constructed lakes capped with natural surface water. The wet landscape method represents potential risk to aquatic biota-naphthenic acids and PAHs elute from pore water contained in the fine-tailings substrate. In spring 1995 yellow perch were stocked into a large-scale (5ha) experimental pond that consisted of fine-tailings capped with natural water as well as into two other reclaimed ponds that were constructed with oil-sands overburden material. Prior to stocking of perch, ponds had colonized with cyprinids, macrophytes and benthic invertebrates over a two year period. Perch were sampled in fall 1995 for age, condition factor, liver size, gonad size, fecundity, stomach contents, liver mixed-function oxygenase activity (MFO), bile PAH metabolites and plasma steroid hormones. When compared to the source lake, perch in the DP did not show reduced reproductive potential. Perch in all of the reclaimed ponds demonstrated exposure to organic compounds as indicated by marginally induced MFO activity and increased liver size. Exposure to naphthenates and PAHs in water as well as ecological environmental factors will be discussed

  18. Response of sesame to population densities and nitrogen fertilization on newly reclaimed sandy soils

    International Nuclear Information System (INIS)

    Noorka, I.R.; Hafiz, S.I.

    2011-01-01

    Two field experiments were conducted at the Experimental Farm of Faculty of Agriculture, Suez Canal University at Ismailia during 2008 and 2009 seasons to study the effect of nitrogen fertilization and planting density on growth , yield, its attributes as well as seed quality of new sesame variety (Taka 2 cv.). On newly reclaimed sandy soils of Ismailia Governorate, Egypt, experimental design in split plots form with four replications was used. Four levels of nitrogen fertilization 55, 105, 155 and 205 Kg/ha were arranged randomly in the main plots and three planting distances between hills (10, 15 and 20 cm, respectively) were distributed at random in the sub plots. Increasing N fertilizer level up to 205 Kg/ha significantly increased plant height, fruiting zone length, height of the first fruiting branch, number of branches and capsules/plant, 1000-seed weight, seed weight/plant, seed oil content (%) and seed and oil yields /ha. Decreasing planting distance from 20 to 15 and 10 cm consistently and significantly increased plant height, height of the first fruiting branch and seed and oil yields /ha. The reverse was true regarding the yield components. These results were expected, since experiment soil was newly reclaimed sandy soil and very poor in the nutrients and organic matter. (author)

  19. Salt composition of groundwater and reclaimed solonetzes in the Baraba Lowland

    Science.gov (United States)

    Semendyaeva, N. V.; Elizarov, N. V.

    2017-10-01

    Solonetzes of experimental trials established in 1981 and 1986 in the Baraba Lowland were examined. It was found that gypsum-based ameliorants improve the soil and lead to a decrease in the content of soluble salts in the soil profile. Exchange processes between cations of the soil adsorption complex and calcium of gypsum were particularly intensive in the first years after gypsum application. This resulted in a sharp rise in the content of soluble salts that migrated down the soil profile to the groundwater. In the following years, the reclaimed solonetzes were desalinized under the conditions of relatively stable groundwater level. On the 30th year after single gypsum application, the groundwater level sharply rose (to 50 cm), and the soil was subjected to the secondary salinization; the contents of bicarbonates, carbonates, and sodium in the soils increased. Spring leaching caused some desalinization, but the content of soluble salts in the upper soil meter increased again in the fall. A close correlation between the salt compositions of the groundwater and the reclaimed solonetzes was revealed.

  20. Simulating the carbon balance in reclaimed forest ecosystems with the FORECAST model

    Energy Technology Data Exchange (ETDEWEB)

    Welham, C. [British Columbia Univ., Vancouver, BC (Canada). Dept. of Forest Sciences, Forest Ecosystem Simulation Group; ForRx Consulting, Belcarra, BC (Canada); 3GreenTree Ecosystem Services Ltd., Belcarra, BC (Canada)

    2010-07-01

    Large emission sources are beginning to report their carbon footprint on an annual basis as a result of government mandates, shareholder demand for disclosure of a company's risk to climate change, and as part of corporate social responsibility initiatives. Oil sands mining is a carbon intensive activity from the perspective of carbon dioxide emissions. The intensity of carbon emissions can be mitigated through technological and process innovations. However, reclamation is the only mining-related activity that directly removes atmospheric carbon dioxide. This presentation described a modeling exercise that had 3 principal objectives, notably to simulate the carbon balance in a developing reclaimed upland forest ecosystem; to explore the relative change in carbon pools over time; and to compare the carbon balance of the reclaimed ecosystem to its natural analogue. The presentation provided a description of the model and methodology and discussed the simulation protocol. Imperial Oil's Kearl Lake operation, which was used as a test case, showed that approximately 83,000 tonnes of carbon dioxide per hectare can be sequestered per year as a result of reclamation. tabs., figs.

  1. Disposing of coal combustion residues in inactive surface mines: Effects on water quality

    International Nuclear Information System (INIS)

    Kim, A.G.; Ackman, T.E.

    1994-01-01

    The disposal of coal combustion residues (CCR) in surface and underground coal mines can provide a stable, low-maintenance alternative to landfills, benefiting the mining and electric power industries. The material may be able to improve water quality at acid generating abandoned or reclaimed coal mine sites. Most combustion residues are alkaline, and their addition to the subsurface environment could raise the pH, limiting the propagation of pyrite oxidizing bacteria and reducing the rate of acid generation. Many of these CCR are also pozzolanic, capable of forming cementitious grouts. Grouts injected into the buried spoil may decrease its permeability and porosity, diverting water away from the pyritic material. Both mechanisms, alkaline addition and water diversion, are capable of reducing the amount of acid produced at the disposal site. The US Bureau of Mines is cooperating in a test of subsurface injection of CCR into a reclaimed surface mine. Initially, a mixture of fly ash, lime, and acid mine drainage (AMD) sludge was injected. Lime was the source of calcium for the formation of the pozzolanic grout. Changes in water quality parameters (pH, acidity, anions, and trace metals) in water samples from wells and seeps indicate a small but significant improvement after CCR injection. Changes in the concentration of heavy metals in the water flowing across the site were apparently influenced by the presence of flyash

  2. Cretaceous planktic foraminiferal biostratigraphy of the Calera Limestone, Northern California, USA

    Science.gov (United States)

    Sliter, W.V.

    1999-01-01

    The Calera Limestone is the largest, most stratigraphically extensive limestone unit of oceanic character included in the Franciscan Complex of northern California. The aim of this paper is to place the Calera Limestone at its type locality (Rockaway Beach, Pacifica) in a high-resolution biostratigraphy utilizing planktic foraminifers studied in thin section. A section, about 110 m-thick, was measured from the middle thrust slice exposed by quarrying on the southwest side of Calera Hill at Pacifica Quarry. Lithologically, the section is divided in two units; a lower unit with 73 m of black to dark-grey limestone, black chert and tuff, and an upper unit with 36.8 m of light-grey limestone and medium-grey chert. Two prominent black-shale layers rich in organic carbon occur 11 m below the top of the lower black unit and at the boundary with overlying light-grey unit, yielding a total organic content (TOC) of 4.7% and 1.8% t.w., respectively. The fossiliferous Calera Limestone section measured at Pacifica Quarry, from the lower black shale, contains eleven zones and three subzones that span approximately 26 m.y. from the early Aptian to the late Cenomanian. The zones indentified range from the Globigerinelloides blowi Zone to the Dicarinella algeriana Subzone of the Rotalipora cushmani Zone. Within this biostratigraphic interval, the Ticinella bejaouaensis and Hedbergella planispira Zones at the Aptian/Albian boundary are missing as are the Rotalipora subticinensis Subzone of the Biticinella breggiensis Zone and the overlying Rotalipora ticinensis Zone in the late Albian owing both to low-angle thrust faulting and to unconformities. The abundance and preservation of planktic foraminifers are poor in the lower part and improve only within the upper G. algerianus Zone. The faunal relationship indicate that the lower black shale occurs in the upper part of the G. blowi Zone and correlates with the Selli Event recognized at global scale in the early Aptian. The upper black

  3. Lithofacies palaeogeography and biostratigraphy of the lowermost horizons of the Middle Triassic Hallstatt Limestones (Argolis Peninsula, Greece

    Directory of Open Access Journals (Sweden)

    Fotini A. Pomoni

    2013-07-01

    Taking into consideration the present location of the Hallstatt Formation, in the context of the Hellenides, an area suitable for the deposition of the Hallstatt Limestones, should be located between the sub-Pelagonian (western part of the Pelagonian zone and Pindos geotectonic zones, which during the Triassic corresponded to a platform slope and a deep ocean, respectively. The widespread Middle Triassic Han Bulog Limestones (ammonoid-bearing pelagic limestones from Triassic successions of the Eastern Alps (Dinarides, Hellenides may have formed partly in similar slope environments.

  4. Holothurian sclerites and conodonts in the Upper Carnian (Tuvalian and Norian Limestones in the Central Kanmik Alps

    Directory of Open Access Journals (Sweden)

    Anton Ramovš

    1992-12-01

    Full Text Available Near Bivouac under the Skuta Mountain (locality 1 in the central Kamnik Alps Upper Carnian Limestones were determined with conodont Epigondolella nodosa Hayashi, holothurian sclerites Calclamnella consona Mostler and C. regularis Stefanov, ammonites and other fossils similar to deeper marine Hallstatt facies of Northern Limestone Alps.Conodonts Epigondolella abneptis (Huckriede and very rich holothurian fauna proved the Norian age for bedded limestones with very frequent large chert nodules on the south slope of the Skuta and on Sleme (loc. 2 and 3. They representdeeper marine facies and a distinct development of the Lower Norian

  5. Using reclaimed lumber and wood flooring in construction : measuring environmental impact using life-cycle inventory analysis

    Science.gov (United States)

    Richard D. Bergman; Hongmei Gu; Robert H. Falk; Thomas R. Napier

    2010-01-01

    With green building concepts becoming widespread in the construction field, building practices and materials are being examined for their environmental impact. Reusing building materials has a distinct advantage over using newly manufactured materials because these reclaimed materials avoid greenhouse gas emissions associated with new (virgin) material manufacturing....

  6. Reclaiming Joy: Pilot Evaluation of a Mental Health Peer Support Program for Older Adults Who Receive Medicaid

    Science.gov (United States)

    Chapin, Rosemary K.; Sergeant, Julie F.; Landry, Sarah; Leedahl, Skye N.; Rachlin, Roxanne; Koenig, Terry; Graham, Annette

    2013-01-01

    Purpose: Stigma and lack of access to providers create barriers to mental health treatment for older adults living in the community. In order to address these barriers, we developed and evaluated a peer support intervention for older adults receiving Medicaid services. Design and Methods: Reclaiming Joy is a mental health intervention that pairs…

  7. Emergy and Economic Evaluations of Four Fruit Production Systems on Reclaimed Wetlands Surrounding the Pearl River Estuary, China

    Science.gov (United States)

    Emergy and economic methods were used to evaluate and compare a traditional tropical fruit cultivation system, for bananas, and three newly introduced fruit cultivation systems, for papaya, guava and wampee, on reclaimed wetlands of the Pearl River Estuary, China. The evaluations...

  8. Effect of using of reclaimed asphalt and/or lower temperature asphalt on the availability of the road network

    NARCIS (Netherlands)

    Nicholls, C.; Wayman, M.; Mollenhauer, K.; McNally, C.; Tabakovic, A.; Varveri, A.; Cassidy, S.; Shahmohammadi, R.; Gilbert, K.

    2014-01-01

    There is a need for a method for assessing the results from changes in the potential durability of road materials due to the inclusion of reclaimed and secondary component materials in the manufacture of new road materials. Such changes will have an effect on the cost of the construction

  9. Survey for the presence of Phytophthora cinnamomi on reclaimed mined lands in Ohio chosen for restoration of the American chestnut

    Science.gov (United States)

    Shiv Hiremath; Kirsten Lehtoma; Jenise M. Bauman

    2013-01-01

    We have been planting blight resistant American chestnut seedlings on reclaimed coal mined areas in Southeastern Ohio, which was once within the natural range of the American chestnut. Towards the goal of restoring the American chestnut, we are testing suitable sites that can aid survival, growth and establishment of planted seedlings pre-inoculated with...

  10. Nesting success of grassland and savanna birds on reclaimed surface coal mines of the midwestern United States

    Energy Technology Data Exchange (ETDEWEB)

    Galligan, E.W.; DeVault, T.L.; Lima, S.L. [Indiana State University, Terre Haute, IN (United States)

    2006-12-15

    Reclaimed surface coal mines in southwestern Indiana support many grassland and shrub/savanna bird species of conservation concern. We examined the nesting success of birds on these reclaimed mines to assess whether such 'unnatural' places represent productive breeding habitats for such species. We established eight study sites on two large, grassland-dominated mines in southwestern Indiana and classified them into three categories (open grassland, shrub/savanna, and a mixture of grassland and shrub/savanna) based on broad vegetation and landscape characteristics. During the 1999 and 2000 breeding seasons, we found and monitored 911 nests of 31 species. Daily nest survival for the most commonly monitored grassland species ranged from 0.903 (Dickcissel, Spiza americana) to 0.961 (Grasshopper Sparrow, Ammodramus savannarum). Daily survival estimates for the dominant shrub/savanna nesting species ranged from 0.932 (Brown Thrasher, Toxostoma rufum) to 0.982 (Willow Flycatcher, Empidonax traillii). Vegetation and landscape effects on nesting success were minimal, and only Eastern Meadowlarks (Sturnella magna) showed a clear time-of-season effect, with greater nesting success in the first half of the breeding season. Rates of Brown-headed Cowbird (Molothrus ater) parasitism were only 2.1% for grassland species and 12.0% for shrub/savanna species. The nesting success of birds on reclaimed mine sites was comparable to that in other habitats, indicating that reclaimed habitats on surface mines do not necessarily represent reproductive traps for birds.

  11. 40 CFR Appendix B1 to Subpart F of... - Performance of Refrigerant Recovery, Recycling and/or Reclaim Equipment

    Science.gov (United States)

    2010-07-01

    ... Refrigeration Institute Standard 740-1993. Refrigerant Recovery/Recycling Equipment Section 1. Purpose 1..., Recycling and/or Reclaim Equipment B1 Appendix B1 to Subpart F of Part 82 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) PROTECTION OF STRATOSPHERIC OZONE Recycling...

  12. Fault architecture and growth in clay-limestone alternations: insights from field observations in the SE Basin, France

    International Nuclear Information System (INIS)

    Rocher, M.; Roche, V.; Homberg, C.

    2012-01-01

    Document available in extended abstract form only. The Callovo-Oxfordian (COX) clayey formation is currently studied by Andra in 'Meuse/Haute- Marne' (MHM), eastern Paris basin (France), for hosting a disposal of high level and intermediate, long-lived radioactive waste. As an independent organisation performing safety reviews for the Nuclear Safety Authority, IRSN conducts studies in support of the review of this disposal project. This nearly 130 m-thick clayey formation is surrounded by two 250 m-thick limestone formations. In such limestone/clay alternations, tectonic fracturing is often observed within limestones and propagates in some cases to clay layers. Such a propagation through the COX within or close to the disposal area could diminish its containment ability by creating preferential pathways of radioactive solute towards limestones. Nevertheless, minor to moderate fracturing is difficult to investigate in hectometre scale multilayer systems such as COX: seismic reflexion surveys only provide data on major faults, drilling data are too localised and clays have a 'bad-land' aspect at surface. The aim of this study is to provide a model of fracturing across clay-limestone alternations so as to strengthen the assessment of their possible development. We thus investigated fracturing within decametre-sized clay-limestone alternations, located in the South-Eastern Basin (France), to determine the evolution of fault architecture during its growth. After analysis of the possible scale effects using data from other analogous fields, an application to the COX in MHM is presented. We studied minor normal faults that reflect various stages of development, from simple fault planes restricted to limestones to complex fault zones propagated across several clay-limestone layers. The analysis of the fault characteristics, the construction of displacement profiles and the results obtained using numerical models enlighten fault growth processes, i.e. nucleation

  13. Evaluation of steel slag and crushed limestone mixtures as subbase material in flexible pavement

    Directory of Open Access Journals (Sweden)

    Ahmed Ebrahim Abu El-Maaty Behiry

    2013-03-01

    Full Text Available Steel slag is produced as a by-product during the oxidation of steel pellets in an electric arc furnace. This by-product that mainly consists of calcium carbonate is broken down to smaller sizes to be used as aggregates in pavement layers. They are particularly useful in areas where a good-quality aggregate is scarce. This research study was conducted to evaluate the effect of quantity of steel slag on the mechanical properties of blended mixes with crushed limestone aggregates, which used as subbase material in Egypt. Moreover, a theoretical analysis was employed to estimate the resistance for failure factors such as vertical deformations, vertical and radial stresses and vertical strains of subbase under overweight trucks loads. These loads cause severe deterioration to the pavement and thus reduce its life. The results indicated that the mechanical characteristics, and the resistance factors were improved by adding steel slag to the crushed limestone.

  14. Compositional characterization of French limestone: a new tool for art historians

    International Nuclear Information System (INIS)

    Holmes, L.L.; Harbottle, G.; Blanc, A.

    1994-01-01

    Limestone from quarries known to medieval craftsmen and from the monuments they built and embellished, as well as from carvings now in museum collections, has been characterized by neutron activation analysis. Specimens form 38 quarries in the Lutetian and Jurassic limestone formations of France and from sculptures in American and French museums have been tested, and the results have been compiled in a data base to which art historians may refer when attempting to determine provenance for sculptures. Multivariate statistical analysis of concentration data shows stone form a particular quarry in the Paris basin to be compositionally homogeneous and distinguishable from other quarries in the same formation. The same approach to data related to quarries near the Burgundian abbey of Cluny finds general agreement between classifications based on compositional and on petrographic data. (Author)

  15. Intermediate-scale sodium-concrete reaction tests with basalt and limestone concrete

    International Nuclear Information System (INIS)

    Hassberger, J.A.; Muhlestein, L.D.

    1981-01-01

    Ten tests were performed to investigate the chemical reactions and rate and extent of attack between sodium and basalt and limestone concretes. Test temperatures ranged from 510 to 870 0 C (950 to 1600 0 F) and test times from 2 to 24 hours. Sodium hydroxide was added to some of the tests to assess the impact of a sodium hydroxide-aided reaction on the overall penetration characteristics. Data suggest that the sodium penetration of concrete surfaces is limited. Penetration of basalt concrete in the presence of sodium hydroxide is shown to be less severe than attack by the metallic sodium alone. Presence of sodium hydroxide changes the characteristics of sodium penetration of limestone concrete, but no major differences in bulk penetration were observed as compared to penetration by metallic sodium

  16. Biological effects of long term fine limestone tailings discharge in a fjord ecosystem.

    Science.gov (United States)

    Brooks, Lucy; Melsom, Fredrik; Glette, Tormod

    2015-07-15

    Benthic infaunal data collected from 1993 to 2010 were analysed to examine the effect of long term discharge of fine limestone tailings on macrofaunal species assemblages in a fjord. Relative distance from the outfall and proportion of fine tailings in the sediment were correlated with benthic community structure. Diversity decreased with increasing proportion of fine tailings. Biological Traits Analysis (BTA) was used to explore the temporal and spatial effects of the tailings gradient on macrofaunal functional attributes. BTA revealed that all stations along a pressure gradient of fine limestone tailings were dominated by free-living species. As the proportion of fine tailings in the sediment increased, there was an increase in fauna that were smaller, highly mobile, living on or nearer the surface sediment, with shorter lifespans. There was a decrease in permanent tube dwellers, those fauna with low or no mobility, that live deeper in the sediment and have longer lifespans (>5 yrs). Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. Physiological and behavioral response of stonefly nymphs to enhanced limestone treatment of acid mine drainage

    Energy Technology Data Exchange (ETDEWEB)

    Cole, M.B.; Arnold, D.E.; Watten, B.J. [ABR Inc., PO Box 249, OR (USA). Environmental Research and Services

    2001-07-01

    A new acid mine drainage (AMD) treatment system uses pulsed, fluidized beds of limestone, and carbon dioxide pretreatment of influent AMD to enhance limestone neutralization of AMD. Laboratory studies were carried out to evaluate the behavior and physiology of larval stoneflies (Pteronarcys proteus, Plecoptera) exposed to effluents produced by the treatment system. Survival, sodium balance, drift, and feeding responses by P. proteus to treated and untreated AMD were examined. P. proteus nymphs exhibited significant losses of whole body sodium in exposures to untreated AMD. Nymphs exposed to treated effluents experienced no loss of whole-body sodium. No significant differences in feeding or drift behavior occurred between nymphs exposed to treated effluents and those exposed to AMD-free controls. The treatment system, with and without CO{sub 2} pretreatment, provided water that was not toxic to the test animals, and that allowed normal behavioral and physiological function.

  18. Hydrobiogeochemical interactions in 'anoxic' limestone drains for neutralization of acidic mine drainage

    Science.gov (United States)

    Robbins, E.I.; Cravotta, C.A.; Savela, C.E.; Nord, G.L.

    1999-01-01

    Processes affecting neutralization of acidic coal mine drainage were evaluated within 'anoxic' limestone drains (ALDs). Influents had pH???3.5 and dissolved oxygen Al3+ and Fe3+ compounds. Cleavage mounts of calcite and gypsum that were suspended within the ALDs and later examined microscopically showed dissolution features despite coatings by numerous bacteria, biofilms, and Fe-Al-Si precipitates. In the drain exhibiting the greatest flow reduction, Al-hydroxysulfates had accumulated on limestone surfaces and calcite etch points, thus causing the decline in transmissivity and dissolution. Therefore, where Al loadings are high and flow rates are low, a pre-treatment step is indicated to promote Al removal before diverting acidic mine water into alkalinity-producing materials. ?? 1998 Elsevier Science Ltd.

  19. Evaluation of modeling approaches to simulate contaminant transport in a fractured limestone aquifer

    DEFF Research Database (Denmark)

    Mosthaf, Klaus; Fjordbøge, Annika Sidelmann; Broholm, Mette Martina

    in fractured limestone aquifers. The model comparison is conducted for a contaminated site in Denmark, where a plume of dissolved PCE has migrated through a fractured limestone aquifer. Field data includes information on spill history, distribution of the contaminant (multilevel sampling), geology...... and hydrogeology. To describe the geology and fracture system, data from borehole logs and cores was combined with an analysis of heterogeneities and fractures from a nearby excavation and pump test data. We present how field data is integrated into the different model concepts. A challenge in the use of field...... and remediation strategies. Each model is compared with field data, considering both model fit and model suitability. Results show a considerable difference between the approaches, and that it is important to select the right one for the actual modeling purpose. The comparison with data showed how much...

  20. Comparison of different modeling approaches to simulate contaminant transport in a fractured limestone aquifer

    DEFF Research Database (Denmark)

    Mosthaf, Klaus; Rosenberg, L.; Balbarini, Nicola

    . Given available field data and model purpose, this paper therefore aims to develop, examine and compare modeling approaches for transport of contaminants in fractured limestone aquifers. The model comparison was conducted for a contaminated site in Denmark, where a plume of a dissolved contaminant (PCE...... was combined with an analysis of heterogeneities and fractures from a nearby excavation (analog site). Methods for translating the geological information and fracture mapping into each of the model concepts were examined. Each model was compared with available field data, considering both model fit...... of field data is the determination of relevant hydraulic properties and interpretation of aqueous and solid phase contaminant concentration sampling data. Traditional water sampling has a bias towards fracture sampling, however concentrations in the limestone matrix are needed for assessing contaminant...

  1. Mechanical and chemical compaction in fine-grained shallow-water limestones.

    Science.gov (United States)

    Shinn, E.A.; Robbin, D.M.

    1983-01-01

    Significant mechanical compaction resulted from pressures simulating less than 305 m of burial. Increasing loads to an equivalent of more than 3400 m did not significantly increase compaction or reduce sediment core length. Chemical compaction (pressure dissolution) was detected only in sediment cores compacted to pressures greater than 3400 m of burial. These short-term experiments suggest that chemical compaction would begin at much shallower depths given geologic time. Compaction experiments that caused chemical compaction lend support to the well-established hypothesis; that cement required to produce a low-porosity/low-permeability fine-grained limestone is derived internally. Dissolution, ion diffusion, and reprecipitation are considered the most likely processes for creating significant thicknesses of dense limestone in the geologic record. Continuation of chemical compaction after significant porosity reduction necessitates expulsion of connate fluids, possibly including hydrocarbons. -from Authors

  2. Soil-gas diffusivity fingerprints of the dual porosity system in fractured limestone

    DEFF Research Database (Denmark)

    Claes, Niels; Chamindu, D.T.K.K.; Jensen, Jacob Birk

    2010-01-01

    processes are mostly limited to hydrogeological (water and solute) transport studies with very poor attention to the gaseous phase transport studies (Kristensen et al. 2010). This study characterizes fractured limestone soils for gas diffusion based on three different gas diffusivity fingerprints. The first...... fingerprint is a two-parameter exponential model, which mainly describes the gas diffusivity in the limestone matrix while taking both fracture connectivity and matrix pore connectivity into account. With the second fingerprint, we make a close observation of the tortuous matrix pore network by means...... of a modified Buckingham (1904) pore connectivity factor (X*). The third fingerprint of the fracture network involves the average angle of diffusion α (Moldrup et al. 2010), a parameter which characterizes the average angle at which the fractures are penetrating the sample....

  3. Arbuscular mycorrhizal fungi in a semi-arid, limestone mining-impacted area of Brazil

    Directory of Open Access Journals (Sweden)

    Thaís Teixeira-Rios

    2013-12-01

    Full Text Available The main goal of this study was to determine the diversity and activity of arbuscular mycorrhizal fungi (AMF in an area degraded by limestone mining within the semi-arid region of Brazil known as the caatinga (shrublands. Near a limestone quarry, we selected two areas of caatinga (preserved and degraded for study. The number of glomerospores did not differ significantly between the two areas. There was a trend toward the most probable number of infective propagules being higher in the degraded area. Twenty AMF taxa were identified in the two sampled areas, species richness, diversity and evenness being higher in the preserved area. Two species of Racocetra represent new records for the semi-arid region of Brazil. Glomerospore production and AMF species richness were unaffected by mining activity in the study area.

  4. Investigations of a Cretaceous limestone with spectral induced polarization and scanning electron microscopy

    DEFF Research Database (Denmark)

    Johansson, Sara; Sparrembom, Charlotte; Fiandaca, Gianluca

    2017-01-01

    limestone was carried out in the Kristianstad basin, Sweden. The time domain IP data was processed with a recently developed method in order to suppress noise from the challenging urban setting in the survey area. The processing also enabled extraction of early decay times resulting in broader spectra...... in early time ranges for bedrock characterization. The inverted sections showed variations within the limestone that could be caused by variations in texture and composition. Samples from a deep drilling in the Kristianstad basin were investigated with scanning electron microscopy and energy dispersive X......Characterization of varying bedrock properties is a common need in various contexts, ranging from large infrastructure pre-investigations to environmental protection. A direct current resistivity and time domain induced polarization (IP) survey aiming to characterize properties of a Cretaceous...

  5. Physico-chemical investigations of limestones from different localities in the Republic of Macedonia

    International Nuclear Information System (INIS)

    Arabadzhiev, Dimitrios M.; Stefov, Viktor; Boev, Blazho

    2001-01-01

    Physico-chemical investigations were carried out for limestone samples at different localities in the Republic of Macedonia: mine for nonmetals O graiden , Strumica (sample-granulation below: 4, 10, 20, 32, 40, 63 and 90 gm), A.D. M ikrogranulat , Gostivar, mine 'Banjani' - Skopje, mine 'Toplica' near Demir Hisar and from the separation of GP Mavrovo, Skopje, located near Pletvar. Investigation of samples from the previously mentioned localities were carried out using different methods: volumetry, gravimetry, UV-VIS and infrared spectroscopy, as well as atomic absorption and X-ray fluorescence spectrometry, X-ray diffraction and flame photometry. The obtained results lead to the conclusion that all granulometric classes of the limestone samples from 'Ograzhden', Strumica, are of the best quality. (Original)

  6. Paleokarst processes in the Eocene limestones of the Pyramids Plateau, Giza, Egypt

    Science.gov (United States)

    El Aref, M. M.; Refai, E.

    The Eocene limestones of the Pyramids plateau are characterized by landforms of stepped terraced escarpment and karst ridges with isolated hills. The carbonate country rocks are also dominated by minor surface, surface to subsurface and subsurface solution features associated with karst products. The systematic field observations eludicate the denudation trend of the minor solution features and suggest the origin of the regional landscapes. The lithologic and structural characters of the limestone country rocks comprise the main factors controlling the surface and subsurface karst evolution. The development of the karst features and the associated sediments in the study area provides information on the paleohydrolic, chemical and climatic environments involved in the origin of the karstification.

  7. Limestone: some observations on luminescence in the region of 360 nm

    International Nuclear Information System (INIS)

    Galloway, R.B.

    2003-01-01

    An empirical study of luminescence around 360 nm from limestone is presented. Thermoluminescence glow curves from natural limestone show broad peaks at 440 deg. C, 350 deg. C, 530 deg. C and 286 deg. C in order of decreasing amplitude in contrast to the usual observation, for luminescence around 535 nm, of a sharp peak at 286 deg. C with a broader less intense peak at 350 deg. C. Recuperation occurs around 350 deg. C and 525 deg. C, which has a time dependence consistent with quantum tunnelling. Dependent on the history of heating and light exposure of the sample, sharp peaks at about 325 deg. C and 425 deg. C can be observed. Laboratory irradiated limestone shows a peak at 140 deg. C. The stimulation of luminescence by light of 470 nm with preheating at 145 deg. C for 300 s, shows an increasing signal for successive cycles of measurement associated with the heating, light exposure having little influence. Beta irradiation of a sample, with the same measurement conditions, gives a signal which increases in proportion to radiation dose but which does not survive storage for 17 h. Time resolved luminescence spectra, with no preheating, show a luminescence lifetime between stimulation and emission of less than a few μs for natural limestone, and an exponential increase in signal with increase in temperature (over the rang 20-167 deg. C) during stimulation. A signal proportional to laboratory applied beta dose is measurable at room temperature, with lifetime between stimulation and emission of this signal of 35 μs, but it does not survive heating to 100 deg. C

  8. [Effects of variable temperature on organic carbon mineralization in typical limestone soils].

    Science.gov (United States)

    Wang, Lian-Ge; Gao, Yan-Hong; Ding, Chang-Huan; Ci, En; Xie, De-Ti

    2014-11-01

    Soil sampling in the field and incubation experiment in the laboratory were conducted to investigate the responses of soil organic carbon (SOC) mineralization to variable temperature regimes in the topsoil of limestone soils from forest land and dry land. Two incubated limestone soils were sampled from the 0-10 cm layers of typical forest land and dry land respectively, which were distributed in Tianlong Mountain area of Puding county, Guizhou province. The soils were incubated for 56 d under two different temperature regimes including variable temperature (range: 15-25 degrees C, interval: 12 h) and constant temperature (20 degrees C), and the cumulative temperature was the same in the two temperature treatments. In the entire incubation period (56 d), the SOC cumulative mineralization (63.32 mg x kg(-1)) in the limestone soil from dry land (SH) under the variable temperature was lower than that (63.96 mg x kg(-1)) at constant 20 degrees C, and there was no significant difference in the SOC cumulative mineralization between the variable and constant temperature treatments (P variable temperature was significantly lower than that (209.52 mg x kg(-1)) at constant 20 degrees C. The results indicated that the responses of SOC mineralization to the variable temperature were obviously different between SL and SH soils. The SOC content and composition were significantly different between SL and SH soils affected by vegetation and land use type, which suggested that SOC content and composition were important factors causing the different responses of SOC mineralization to variable temperature between SL and SH soils. In addition, the dissolved organic carbon (DOC) content of two limestone soils were highly (P variable temperature mainly influenced SOC mineralization by changing microbial community activity rather than by changing microbial quantity.

  9. Towards Early Age Characterisation of Eco-Concrete Containing Blast-Furnace Slag and Limestone Filler

    OpenAIRE

    Carette, Jerome

    2015-01-01

    It is estimated that concrete represents 5% of the anthropogenic CO2 emissions, mainly originating from the production of cement, the most essential component of concrete. The recent awareness to the environmental challenges facing our civilization has led the cement industry to consider substituting cement by mineral additions, by-products of existing industries. In this work, a combination of limestone filler and blast furnace slag is used to design an “eco-concrete”, defined as a concrete ...

  10. Estimation of deep infiltration in unsaturated limestone environments using cave lidar and drip count data

    OpenAIRE

    Mahmud, K.; Mariethoz, G.; Baker, A.; Treble, P. C.; Markowska, M.; McGuire, E.

    2016-01-01

    Limestone aeolianites constitute karstic aquifers covering much of the western and southern Australian coastal fringe. They are a key groundwater resource for a range of industries such as winery and tourism, and provide important ecosystem services such as habitat for stygofauna. Moreover, recharge estimation is important for understanding the water cycle, for contaminant transport, for water management, and for stalagmite-based paleoclimate reconstructions. Caves offer a n...

  11. Block Volume Estimation from the Discontinuity Spacing Measurements of Mesozoic Limestone Quarries, Karaburun Peninsula, Turkey

    OpenAIRE

    Elci, Hakan; Turk, Necdet

    2014-01-01

    Block volumes are generally estimated by analyzing the discontinuity spacing measurements obtained either from the scan lines placed over the rock exposures or the borehole cores. Discontinuity spacing measurements made at the Mesozoic limestone quarries in Karaburun Peninsula were used to estimate the average block volumes that could be produced from them using the suggested methods in the literature. The Block Quality Designation (BQD) ratio method proposed by the authors has been found to ...

  12. Mississippian reef development in the Cracoe Limestone Formation of the southern Askrigg Block, North Yorkshire, UK

    OpenAIRE

    Waters, C.N.; Haslam, R.B.; Cózar, P.; Somerville, I.D.; Millward, D.; Woods, M.

    2017-01-01

    The southern margin of the Askrigg Block around Cracoe, North Yorkshire, shows a transition from carbonate ramp to reef-rimmed shelf margin, which, based on new foraminiferal/algal data, is now constrained to have initiated during the late Asbian. A late Holkerian to early Asbian ramp facies that included small mudmounds developed in comparatively deeper waters, in a transition zone between the proximal ramp, mudmound-free carbonates of the Scaleber Quarry Limestone Member (Kilnsey Formation)...

  13. Limestone and oyster shell for brown layers in their second egg production cycle

    Directory of Open Access Journals (Sweden)

    CC Pizzolante

    2011-06-01

    Full Text Available This study aimed at evaluating the effect of dietary calcium levels and the replacement of calcium sources with different particle size compositions on the performance and egg quality of brown layers in their second egg production cycle. A randomized block experimental design was applied with 12 treatments in a 3x4 factorial arrangement: three calcium levels (2.6, 3.2, 3.8 % and four combinations of calcium sources (1- 100% fine limestone (FL, 2- 50% FL + 50% coarse limestone (CL, 3- 50% FL and 50% oyster shell (OS, 4- 50% FL and 25% CL+ 25 %OS, with six replicates of eight birds each. Calcium sources were analyzed for geometric mean diameter (GMD and in-vitro solubility. The following performance and egg quality parameters were evaluated: egg weight (EW, g, egg production (% Eggs, egg mass (EM %, feed intake (FI g, feed conversion ratio (FCR kg/dz and FCR kg/kg, mortality (% Mort., specific egg gravity (SG, percentages of yolk (Y%, albumen (Alb% and eggshell (ES%, eggshell thickness (EST, eggshell breaking strength (BS, eggshell weight per surface area (EWSA, Haugh unit (HU, yolk index (YI and yolk color. Performance and internal egg quality were not affected by the treatments (p>0.05. Blocks had a significant effect on (p<0.05 FI and FCR (kg/dz and kg/kg. Treatments significantly influenced external egg quality, which improved as dietary calcium levels increases and when up to 50% fine limestone was replaced by combinations of coarse limestone with oyster shell.

  14. Stability of an anaerobic single reactor filled with dolomitic limestone with increased organic load of sugarcane

    Directory of Open Access Journals (Sweden)

    Maria Magdalena Ribas Döll

    2017-12-01

    Full Text Available The anaerobic single-stage reactor was evaluated to treat vinasse and to evaluate its stability. This bench reactor was filled with dolomitic limestone with a horizontal plug flow to simulate a drainage channel. The experiment lasted 129 days while the reactor was submitted to different applied organic concentrations (chronologically applied: 3.0; 5.0; 12.0; 9.0 and 7.5 g L-1 as COD, chemical oxygen demand. COD removals were 50% and 9% with 3.0 and 7.5 g L-1, respectively. With 12.0 g L-1, reactor efficiency increased to 33%, with an abrupt drop to 3% on the 84th day. Therefore, in order to avoid reactor collapse, a remedial measure was necessary. The system remained in batch without feeding for 19 days (from the 85th to the 104th day with 9.0 g L-1. Afterwards, it was observed that the performance of the system tended to stabilize, reaching 47% with 7.5 g L-1 in the 118th day. At the end of the experiment, the potassium content of the wastewater decreased from 800 mg L-1 to 594 mg L-1 (on an average 25% and calcium and magnesium increased within the reactor liquor. The dissolution of the limestone inside the liquor reactor probably caused this result. After the treatment with limestone, the average pH value of the effluent increased from 4.9 to over 6.0 in all organic concentrations. It could be concluded that the reactor filled with dolomitic limestone in these operational conditions assured a low efficiency in COD removal, potassium reduction, increasing values of pH, alkalinity, calcium and magnesium. The instability was observed when there was increase in organic load to 12 g L-1 with subsequent recovery.

  15. Determination of calcium and iron in limestone by X-ray fluorescence method

    International Nuclear Information System (INIS)

    Sovtsova, M.K.

    1977-01-01

    The results of determining calcium and iron content in limestone by X-ray fluorescence method are described. The 109 Cd isotape was chosen as a source for excitation, as it permited to reduce the concentration degeneration in the range of large Ca contents due to the larger energy of the primary radiation. The root-mean-square deviation from the data of chemical analysis was +-0.02%FeO and +-0.22%CaO

  16. Dinosaur footprints in the Upper Turonian-Coniacian limestone in the Krnica Bay (NE Istria, Croatia

    Directory of Open Access Journals (Sweden)

    Alenka Mauko

    2003-06-01

    Full Text Available Three isolated footprints and one trackway that can be attributed to bipedal dinosaur, from a limestone bed in vicinity of Požara promontory, Krnica Bay, are described. According to the stratigraphic position the footprints are late Turonian to Coniacian in age.This is the first record of dinosaur remains in the Turonian-Coniacian and the youngest footprint site on the Adriatic-Dinaric Carbonate Platform described thus far.

  17. Health risks from exposure to Legionella in reclaimed water aerosols: Toilet flushing, spray irrigation, and cooling towers.

    Science.gov (United States)

    Hamilton, Kerry A; Hamilton, Mark T; Johnson, William; Jjemba, Patrick; Bukhari, Zia; LeChevallier, Mark; Haas, Charles N

    2018-05-01

    The use of reclaimed water brings new challenges for the water industry in terms of maintaining water quality while increasing sustainability. Increased attention has been devoted to opportunistic pathogens, especially Legionella pneumophila, due to its growing importance as a portion of the waterborne disease burden in the United States. Infection occurs when a person inhales a mist containing Legionella bacteria. The top three uses for reclaimed water (cooling towers, spray irrigation, and toilet flushing) that generate aerosols were evaluated for Legionella health risks in reclaimed water using quantitative microbial risk assessment (QMRA). Risks are compared using data from nineteen United States reclaimed water utilities measured with culture-based methods, quantitative PCR (qPCR), and ethidium-monoazide-qPCR. Median toilet flushing annual infection risks exceeded 10 -4 considering multiple toilet types, while median clinical severity infection risks did not exceed this value. Sprinkler and cooling tower risks varied depending on meteorological conditions and operational characteristics such as drift eliminator performance. However, the greatest differences between risk scenarios were due to 1) the dose response model used (infection or clinical severity infection) 2) population at risk considered (residential or occupational) and 3) differences in laboratory analytical method. Theoretical setback distances necessary to achieve a median annual infection risk level of 10 -4 are proposed for spray irrigation and cooling towers. In both cooling tower and sprinkler cases, Legionella infection risks were non-trivial at potentially large setback distances, and indicate other simultaneous management practices could be needed to manage risks. The sensitivity analysis indicated that the most influential factors for variability in risks were the concentration of Legionella and aerosol partitioning and/or efficiency across all models, highlighting the importance of

  18. RECLAIM V2.0: comparison of calculated doses with other assessment tools when emulating contaminated land scenarios

    International Nuclear Information System (INIS)

    Willans, Mark; Galais, Nathalie; Lennon, Chris; Trivedil, Divyesh

    2007-01-01

    ReCLAIM v2.0 is a software tool designed to calculate doses to exposure groups from radioactively contaminated land including UK Nuclear Licensed Sites. When using tools to undertake contaminated land assessments, it is important to understand the functionality of the tool and how the tool should be best used to undertake an assessment. This work describes the results from inter-comparison of ReCLAIM v2.0 with two other radioactively contaminated land tools (Conland and RCLEA). For the majority of cases there was little difference between ReCLAIM v2.0 and the other tools. In all cases where there were significant differences, the cause of the variation could be explained and quantified. In the majority of these cases the main exposure pathway was external irradiation. In these cases, variations in the calculated doses were due to the differing ways in which underpinning shielding calculations were undertaken to calculate external radiation dose coefficients. The effect was most noticeable for radionuclides emitting high energy penetrating radiation such as Co-60, Cs-134 and Cs-137. For these cases, there was a greater difference of up to around 60% in the dose comparisons between ReCLAIM v2.0 and the alternative tools, with ReCLAIM v2.0 being more conservative. These results demonstrate that where the algorithms and parameter values are similar, different tools will produce similar results. The user of such tools should be aware of cases where different results may be produced in order that an appropriate level of confidence can be assigned when making decisions based upon the results. (authors)

  19. Decomposition and reduction of N2O over Limestone under FBC Conditions

    DEFF Research Database (Denmark)

    Johnsson, Jan Erik; Jensen, Anker; Vaaben, Rikke

    1997-01-01

    The addition of limestone for sulfur retention in FBC has in many cases been observed to influence the emission of N2O. The catalytic activity of N2O over calcined Stevns Chalk for decomposition of N2O in a laboratory fixed bed quartz reactor was measured. It was found that calcined Stevns Chalk...... is a very active catalyst for N2O decomposition in an inert atmosphere, and the presence of 3 vol% CO increased the rate of N2O destruction by a factor of 5 due to the catalytic reduction of N2O by CO. The activity decreased with increasing CO2 concentration, and uncalcined or recarbonated limestone had...... negligible activity. Sulfation of the calcined limestone under oxidizing conditions lowered the activity, however sulfidation under reducing conditions showed that CaS is an active catalyst for the reduction of N2O by CO. Without CO present a gas solid reaction between N2O and CaS takes place and SO2...

  20. Experimental study of the effect of limestone grading on some mechanical properties of concrete

    Directory of Open Access Journals (Sweden)

    Ammari Madiha Z. J.

    2017-01-01

    Full Text Available This study reports the experimental work undertaken to investigate the optimum grading of limestone to be used in concrete mixes. 36 concrete cubes were prepared for testing. Four different Fineness Moduli and grading were tested 2.4, 2.6, 2.92 and 3. For all tests, the cubes were left in curing until testing at the age of 3, 7 and 28 days respectively. Samples were loaded to failure and the average compressive strength was used for comparison purposes. Flow table test has been performed on the fresh concrete directly after mixing to measure workability and the average of the maximum concrete spread parallel to the two edges of the table was recorded. Results revealed that the optimum Fineness Modulus for the limestone to be used as fine aggregate in the concrete mix to get maximum compressive strength is 2.78. The flow table tests revealed an increment in the workability of fresh concrete with higher Fineness Modulus of limestone used in the concrete mix as fine aggregate. The workability of the optimum Fineness Modulus, 2.78, was found to be 412 mm which is a mix with considerable workability. An ideal grading has been recommended in this research study and checked to match the ASTM grading requirements for fine aggregate.

  1. TL glow curve analysis of UV, beta and gamma induced limestone collected from Amarnath holy cave

    Directory of Open Access Journals (Sweden)

    Vikas Dubey

    2015-01-01

    Full Text Available The paper reports themoluminescence glow curve analysis of UV (ultraviolet, β (beta and γ (gamma induced limestone collected from Amarnath holy cave. The collected natural sample was characterized by X-ray diffraction (XRD technique and crystallite size calculated by Scherer's formula. Surface morphology and particle size was calculated by transmission electron microscopy (TEM study. Effect of annealing temperature on collected lime stone examined by TL glow curve study. The limestone was irradiated by UV radiation (254 nm source and the TL glow curve recorded for different UV exposure time. For beta irradiation Sr90 source was used and is shows intense peak at 256 °C with a shoulder peak at higher temperature range. For gamma radiation Co60 source and TL glow curve recorded for different doses of gamma. The kinetic parameters calculation was performed for different glow curve by computerized glow curve deconvolution (CGCD technique. The chemical composition of natural limestone was analyzed by energy dispersive X-ray spectroscopy (EDXS.

  2. The influence of temperature on limestone sulfation and attrition under fluidized bed combustion conditions

    Energy Technology Data Exchange (ETDEWEB)

    Montagnaro, Fabio [Dipartimento di Chimica - Universita degli Studi di Napoli Federico II, Complesso Universitario del Monte di Sant' Angelo, 80126 Napoli (Italy); Salatino, Piero [Istituto di Ricerche sulla Combustione - CNR, Piazzale Vincenzo Tecchio 80, 80125 Napoli (Italy); Dipartimento di Ingegneria Chimica - Universita degli Studi di Napoli Federico II, Piazzale Vincenzo Tecchio 80, 80125 Napoli (Italy); Scala, Fabrizio [Istituto di Ricerche sulla Combustione - CNR, Piazzale Vincenzo Tecchio 80, 80125 Napoli (Italy)

    2010-04-15

    The influence of temperature on attrition of two limestones during desulfurization in a fluidized bed reactor was investigated. Differences in the microstructure of the two limestones were reflected by a different thickness of the sulfate shell formed upon sulfation and by a different value of the ultimate calcium conversion degree. Particle attrition and fragmentation were fairly small under moderately bubbling fluidization conditions for both limestones. An increase of temperature from 850 C to 900 C led to an increase of the attrition rate, most likely because of a particle weakening effect caused by a faster CO{sub 2} evolution during calcination. This weakening effect, however, was not sufficiently strong to enhance particle fragmentation in the bed. The progress of sulfation, associated to the build-up of a hard sulfate shell around the particles, led in any case to a decrease of the extent of attrition. Sulfation at 900 C was less effective than at 850 C, and this was shown to be related to the porosimetric features of the different samples. (author)

  3. Treatment of iron(II)-rich acid mine water with limestone and oxygen.

    Science.gov (United States)

    Mohajane, G B; Maree, J P; Panichev, N

    2014-01-01

    The main components of acid mine water are free acid, sulphate, and Fe²⁺. Limestone is the most cost-effective alkali that can be used for neutralization. The purpose of this investigation was to identify conditions where Fe²⁺ is removed with limestone and simultaneously oxidized with oxygen to Fe³⁺, in a polyvinyl chloride pipe under pressure. Gypsum scaling is prevented by passing rubber balls through the pipe of the so-called Oxygen-Pipe-Neutralization (OPeN) process pilot plant. Two synthetic waters were treated: (A) acid mine water containing 123 mg L⁻¹ Fe²⁺ representing gold mine water, and (B) acid mine water containing 6,032 mg L⁻¹ Fe²⁺ representing coal mine water. Batch studies were carried out in a pipe reactor and showed that the rate of Fe²⁺ oxidation depended on the Fe²⁺ concentration, oxygen pressure, amount of recycled sludge, limestone dosage and the mixing rate. Continuous studies in an OPeN process pilot plant resulted in 100% removal of total acidity from synthetic coal mine water and a 98% removal from synthetic gold mine water. Fe²⁺ was removed completely as precipitated Fe(OH)₃ from both synthetic coal and gold mine water at around pH 7 at 200 and 100 kPa oxygen pressure, respectively.

  4. Report of investigation on underground limestone mines in the Ohio region

    International Nuclear Information System (INIS)

    Byerly, D.W.

    1976-06-01

    The following is a report of investigation on the geologic setting of several underground limestone mines in Ohio other than the PPG mine at Barberton, Ohio. Due to the element of available time, the writer is only able to deliver a brief synopsis of the geology of three sites visited. These three sites and the Barberton, Ohio site are the only underground limestone mines in Ohio to the best of the writer's knowledge. The sites visited include: (1) the Jonathan Mine located near Zanesville, Ohio, and currently operated by the Columbia Cement Corporation; (2) the abandoned Alpha Portland Cement Mine located near Ironton, Ohio; and (3) the Lewisburg Mine located at Lewisburg, Ohio, and currently being utilized as an underground storage facility. Other remaining possibilities where limestone is being mined underground are located in middle Ordovician strata near Carntown and Maysville, Kentucky. These are drift mines into a thick sequence of carbonates. The writer predicts, however, that these mines would have some problems with water due to the preponderance of carbonate rocks and the proximity of the mines to the Ohio River. None of the sites visited nor the sites in Kentucky have conditions comparable to the deep mine at Barberton, Ohio

  5. Economical assessment of competitive enhanced limestones for CO2 capture cycles in power plants

    International Nuclear Information System (INIS)

    Romeo, Luis M.; Lara, Yolanda; Lisbona, Pilar; Martinez, Ana

    2009-01-01

    CO 2 capture systems based on the carbonation/calcination loop have gained rapid interest due to promising carbonator CO 2 capture efficiency, low sorbent cost and no flue gases treatment is required before entering the system. These features together result in a competitively low cost CO 2 capture system. Among the key variables that influence the performance of these systems and their integration with power plants, the carbonation conversion of the sorbent and the heat requirement at calciner are the most relevant. Both variables are mainly influenced by CaO/CO 2 ratio and make-up flow of solids. New sorbents are under development to reduce the decay of their carbonation conversion with cycles. The aim of this study is to assess the competitiveness of new limestones with enhanced sorption behaviour applied to carbonation/calcination cycle integrated with a power plant, compared to raw limestone. The existence of an upper limit for the maximum average capture capacity of CaO has been considered. Above this limit, improving sorbent capture capacity does not lead to the corresponding increase in capture efficiency and, thus, reduction of CO 2 avoided cost is not observed. Simulations calculate the maximum price for enhanced sorbents to achieve a reduction in CO 2 removal cost under different process conditions (solid circulation and make-up flow). The present study may be used as an assessment tool of new sorbents to understand what prices would be competitive compare with raw limestone in the CO 2 looping capture systems. (author)

  6. Stable isotope stratigraphy and larger benthic foraminiferal extinctions in the Melinau Limestone, Sarawak

    Science.gov (United States)

    Cotton, Laura J.; Pearson, Paul N.; Renema, Willem

    2014-01-01

    Important long-ranging groups of larger benthic foraminifera (LBF) are known to have become extinct during a period of global cooling and climate disruption at the Eocene-Oligocene transition (EOT) but the precise timing and mechanisms are uncertain. Recent study showed unexpectedly that the LBF extinction in Tanzania occurs very close to the Eocene/Oligocene boundary, as recognised by the extinction of the planktonic foraminiferal Family Hantkeninidae, rather than at the later period of maximum global ice growth and sea-level fall, as previously thought. Here we investigate the same phase of extinction in the Melinau Limestone of Sarawak, on the island of Borneo, Malaysia one of the most complete carbonate successions spanning the Eocene to Lower Miocene. Assemblages of LBF from the Melinau Limestone were studied extensively by Geoffrey Adams during the 1960s-80s, confirming a major extinction during the EOT, but the section lacked independent means of correlation. By analysing rock samples originally studied by Adams and now in the Natural History Museum, London, we provide new bulk stable isotope (δ13C and δ18O) records. This enables us to identify, albeit tentatively, the level of maximum stable isotope excursion and show that the LBF extinction event in the Melinau Limestone occurs below this isotope excursion, supporting the results from Tanzania and indicating that the extinction of LBF close to the Eocene/Oligocene boundary may be a global phenomenon.

  7. A Stranger in the Midst: Searching for Relict Grains from Rare Meteorite Types in Mid-Ordovician Limestone Strata

    Science.gov (United States)

    Martin, E.; Schmitz, B.

    2016-08-01

    A layer of Mid-Ordovician limestone harbors exceptional amounts of L-chondritic chromite grains. The layer also contains grains from potentially rarer types of meteorites, following the discovery of the fossil meteorite Österplana 065.

  8. Reduction of SO sub 2 emission from a fluidized-bed under staged combustion by coarse limestone

    International Nuclear Information System (INIS)

    Khan, W.Z.; Gibbbs, B.M.

    1998-01-01

    A study was performed to investigate the effect of course limestone on the reduction of SO sub 2 emission from a fluidized-bed under staged combustion. The limestone of 1.2-2.5 mm size was premixed with fine coal of 1-3 mm size and fed under bed. The staging levels, bed height, and Ca/S ratio was fixed at 70:30, 30 cm and 3:1, respectively. A maximum of around 50% reduction in SO sub 2 emissions was achieved at both excess air of 20 and 40% and at 830 deg. C. bed temperature. The SO sub 2 emissions were very sensitive to bed temperature. The course limestone was found better in desulfurization efficiency at lower temperature than fine limestone. (author)

  9. Discontinuity surfaces and event stratigraphy of Okha Shell Limestone Member: Implications for Holocene sea level changes, western India

    Science.gov (United States)

    Bhonde, Uday; Desai, Bhawanisingh G.

    2011-08-01

    The Okha Shell Limestone Member of Chaya Formation is the coarse grained, shell rich deposit commonly recognized as the beach rocks. It has been age bracketed between Late Pleistocene and Holocene. Late Quaternary sea level changes have been studied with beach rocks along the Saurashtra coastal region. The present study has been carried out in the Okhamandal area of the Saurashtra peninsula especially on the Okha Shell Limestone Member as exposed at various locations along the coast from north to south. Temporal and spatial correlations of the observations have revealed three events in the Okha Shell Limestone Member of Chaya Formation that are correlated laterally. The events show depositional breaks represented by discontinuity surfaces, the taphofacies varieties and ichnological variations. The present study in the context of available geochrnological data of the region suggests a prominent depositional break representing low sea level stand (regression) during an Early Holocene during the deposition of Okha Shell Limestone Member.

  10. Impacts of reclaimed water irrigation on soil antibiotic resistome in urban parks of Victoria, Australia

    International Nuclear Information System (INIS)

    Han, Xue-Mei; Hu, Hang-Wei; Shi, Xiu-Zhen; Wang, Jun-Tao; Han, Li-Li; Chen, Deli; He, Ji-Zheng

    2016-01-01

    The effluents from wastewater treatment plants have been recognized as a significant environmental reservoir of antibiotics and antibiotic resistance genes (ARGs). Reclaimed water irrigation (RWI) is increasingly used as a practical solution for combating water scarcity in arid and semiarid regions, however, impacts of RWI on the patterns of ARGs and the soil bacterial community remain unclear. Here, we used high-throughput quantitative PCR and terminal restriction fragment length polymorphism techniques to compare the diversity, abundance and composition of a broad-spectrum of ARGs and total bacteria in 12 urban parks with and without RWI in Victoria, Australia. A total of 40 unique ARGs were detected across all park soils, with genes conferring resistance to β-lactam being the most prevalent ARG type. The total numbers and the fold changes of the detected ARGs were significantly increased by RWI, and marked shifts in ARG patterns were also observed in urban parks with RWI compared to those without RWI. The changes in ARG patterns were paralleled by a significant effect of RWI on the bacterial community structure and a co-occurrence pattern of the detected ARG types. There were significant and positive correlations between the fold changes of the integrase intI1 gene and two β-lactam resistance genes (KPC and IMP-2 groups), but no significant impacts of RWI on the abundances of intI1 and the transposase tnpA gene were found, indicating that RWI did not improve the potential for horizontal gene transfer of soil ARGs. Taken together, our findings suggested that irrigation of urban parks with reclaimed water could influence the abundance, diversity, and compositions of a wide variety of soil ARGs of clinical relevance. One-sentence summary: Irrigation of urban parks with treated wastewater significantly increased the abundance and diversity of various antibiotic resistance genes, but did not significantly enhance their potential for horizontal gene transfer

  11. Nitrogen utilization and digestibility of amino acids by lambs fed a high-concentrate diet with limestone or magnesium oxide.

    Science.gov (United States)

    Christiansen, M L; Webb, K E

    1990-07-01

    Effects were evaluated of high dietary levels of magnesium oxide (MgO) or limestone on DM, OM and CP digestibility, N balance and intestinal absorption of amino acids by lambs fed a high concentrate diet. Twelve wether lambs equipped with abomasal and ileal cannulas were blocked by weight and breeding and allotted to treatments in a randomized block design in two consecutive trials. Diets were control (800 g), control plus 1.5% MgO (812 g), control plus 1.5% limestone (812 g) and control plus 3.0% limestone (824 g) fed in two equal portions at 12-h intervals. Ruminal fluid pH differences were small. The pH of ileal digesta was greater (P less than .05) with MgO than with limestone (8.23 vs 7.73). Fecal pH was higher (P less than .01) for lambs fed all mineral treatments (avg 8.75) than for lambs fed the control (7.61) and was higher (P less than .01) when MgO (9.53) rather than limestone (8.36) was fed. Ruminal NH3N was lower (P less than .01) when lambs were fed MgO (11.9 mg/dl) compared with limestone (avg 31.2 mg/dl). Preintestinal DM digestibility was greatest (P less than .10) with limestone (avg 49.5%) feeding compared with feeding MgO (31.2%) or the control (35.4%). About 41.5% more essential (P less than .05) and 48% more nonessential (P less than .03) amino acids reached the small intestine when MgO was fed than when limestone was fed. Partial digestibility of amino acids in the small intestine was reduced (P less than .03) an average of 5 percentage units when MgO or limestone was fed. Feeding high levels of MgO or limestone to lambs did not improve the overall digestibility of DM, OM or CP. In fact, feeding high levels of MgO or limestone appeared to be detrimental, reducing intestinal absorption of amino acids.

  12. Residual gas analysis

    International Nuclear Information System (INIS)

    Berecz, I.

    1982-01-01

    Determination of the residual gas composition in vacuum systems by a special mass spectrometric method was presented. The quadrupole mass spectrometer (QMS) and its application in thin film technology was discussed. Results, partial pressure versus time curves as well as the line spectra of the residual gases in case of the vaporization of a Ti-Pd-Au alloy were demonstrated together with the possible construction schemes of QMS residual gas analysers. (Sz.J.)

  13. Geologic framework and hydrogeologic characteristics of the Glen Rose limestone, Camp Stanley Storage Activity, Bexar County, Texas

    Science.gov (United States)

    Clark, Allan K.

    2004-01-01

    The Trinity aquifer is a regional water source in the Hill Country of south-central Texas that supplies water for agriculture, commercial, domestic, and stock purposes. Rocks of the Glen Rose Limestone, which compose the upper zone and upper part of the middle zone of the Trinity aquifer, crop out at the Camp Stanley Storage Activity (CSSA), a U.S. Army weapons and munitions supply, maintenance, and storage facility in northern Bexar County (San Antonio area) (fig. 1). On its northeastern, eastern, and southern boundaries, the CSSA abuts the Camp Bullis Training Site, a U.S. Army field training site for military and Federal government agencies. During 2003, the U.S. Geological Survey (USGS), in cooperation with the U.S. Army, studied the outcropping Glen Rose Limestone at the CSSA and immediately adjacent area (Camp Stanley study area, fig. 1) to identify and map the hydrogeologic subdivisions and faults of the Glen Rose Limestone at the facility. The results of the study are intended to help resource managers improve their understanding of the distribution of porosity and permeability of the outcropping rocks, and thus the conditions for recharge and the potential for contaminants to enter the Glen Rose Limestone. This study followed a similar study done by the USGS at Camp Bullis (Clark, 2003). The purpose of this report is to present the geologic framework and hydrogeologic characteristics of the Glen Rose Limestone in the study area. The hydrogeologic nomenclature follows that introduced by Clark (2003) for the outcropping Glen Rose Limestone at Camp Bullis in which the upper member of the Glen Rose Limestone (hereinafter, upper Glen Rose Limestone), which is coincident with the upper zone of the Trinity aquifer, is divided into five intervals on the basis of observed lithologic and hydrogeologic properties. An outcrop map, two generalized sections, related illustrations, and a table summarize the description of the framework and distribution of characteristics.

  14. Liquid carbon dioxide/pulverized limestone globulsion delivery system for deep ocean storage

    Energy Technology Data Exchange (ETDEWEB)

    Swett, P.; Golomb, D.; Barry, E.; Ryan, D.; Lawton, C. [Massachusetts Univ., Lowell, MA (United States)

    2005-07-01

    Ocean storage of carbon dioxide (CO{sub 2}) raises serious environmental, technical and economic problems because a massive point injection of pure liquid CO{sub 2} at depth would create a plume of carbonic acid with a pH lower than 7. Acidified seawater is considered to be harmful to aquatic organisms. Laboratory studies have shown that injecting a globulsion consisting of CO{sub 2}, water (H{sub 2}O) and calcium carbonate (CaCO{sub 3}) instead of pure liquid CO{sub 2} results in an alkaline reaction rather than an acidic reaction. Because calcium carbonate and bicarbonate are natural ingredients of seawater, there is no expected harm due to the additive limestone. This paper presented a practical delivery system for the underwater creation of globulsion. When liquid or supercritical CO{sub 2} is mixed with a slurry of finely pulverized limestone (CaCO{sub 3}) in pure or seawater, a macro-emulsion is formed consisting of CO{sub 2} droplets coated with CaCO{sub 3} particles dispersed in water. In this study, liquid CO{sub 2} was piped to approximately 500 m depth, which is below the flash point of liquid CO{sub 2} into vapor. A slurry of pulverized limestone in seawater was also separately piped to this depth. A static mixer was mounted at the end of the pipes. Liquid CO{sub 2}, along with a slurry of pulverized limestone and ambient seawater were pumped into the mixer by a turbine. The globulsion exited from the other end of the mixer and sank like a dense plume to greater depths while entraining ambient seawater. The CaCO{sub 3}-coated globules precipitated from the neutrally buoyant plume toward the ocean bottom following equilibration. As such, the ocean was not be acidified with this method of CO{sub 2} discharging. It was concluded that even inland seas, such as the Mediterranean and Black Seas, could be considered for sequestration of a CO{sub 2}/H{sub 2}O/CaCO{sub 3} globulsion. Although adding pulverized limestone to liquid CO{sub 2} and the mixing

  15. Petrophysical and transport parameters evolution during acid percolation through structurally different limestones

    Science.gov (United States)

    Martinez Perez, Laura; Luquot, Linda

    2017-04-01

    Processes affecting geological media often show complex and unpredictable behavior due to the presence of heterogeneities. This remains problematic when facing contaminant transport problems, in the CO2 storage industry or dealing with the mechanisms underneath natural processes where chemical reactions can be observed during the percolation of rock non-equilibrated fluid (e.g. karst formation, seawater intrusion). To understand the mechanisms taking place in a porous medium as a result of this water-rock interaction, we need to know the flow parameters that control them, and how they evolve with time as a result of that concurrence. This is fundamental to ensure realistic predictions of the behavior of natural systems in response of reactive transport processes. We investigate the coupled influence of structural and hydrodynamic heterogeneities in limestone rock samples tracking its variations during chemical reactions. To do so we use laboratory petrophysical techniques such as helium porosimetry, gas permeability, centrifugue, electrical resistivity and sonic waves measurements to obtain the parameters that characterize flow within rock matrix (porosity, permeability, retention curve and pore size distribution, electrical conductivity, formation factor, cementation index and tortuosity) before and after percolation experiments. We built an experimental setup that allows injection of acid brine into core samples under well controlled conditions, monitor changes in hydrodynamic properties and obtain the chemical composition of the injected solution at different stages. 3D rock images were also acquired before and after the experiments using a micro-CT to locate the alteration processes and perform an acurate analysis of the structural changes. Two limestones with distinct textural classification and thus contrasting transport properties have been used in the laboratory experiments: a crinoid limestone and an oolithic limestone. Core samples dimensions were 1 inch

  16. Aristotle Reclaimed

    Science.gov (United States)

    Zimmerman, John; Sharp, Taylor

    2013-01-01

    Given that social media dominates informal and often formal communication routes, we argue that schools must reshape their attention to a fourth rhetorical dimension: the media through which they communicate. Specifically, schools must find ways to embrace social media as a mechanism to reach their broad audiences. This article identifies clear…

  17. Effects of Water and Low-Medium Temperature on Limestone from Mt Etna basement

    Science.gov (United States)

    Castagna, Angela; Ougier-Simonin, Audrey; Benson, Philip; Browning, John; Fazio, Marco; Walker, Richard; Vinciguerra, Sergio

    2017-04-01

    Mount Etna volcano, Sicily, sits atop a structurally complex sedimentary basement continuously subjected to tectonic deformation. The flyschoid formations belonging to the Appenninic-Maghrebian Chain (AMC) and making up the accretionary wedge of a regional fold-and-thrust belt lie above carbonate Hyblean Plateau (HP) sequences, belonging to the African plate. Carbonate rocks represent a major component of the sedimentary basement: they are spread throughout the AMC as continuous strata and discontinuous lenses, and are the main constituent (e.g., Comiso Limestone) of the HP foreland. Etna is an active volcanic environment, characterized by complex stress field distributions, magmatic and non-magmatic fluid circulation, and elevated temperature gradients; the edifice has been constructed at various rates and with variable distribution of effusive products. These intrinsic and extrinsic parameters are known to impact the rheological behaviour of rocks. Previous triaxial deformation studies on carbonates (Tavel Limestone, Solnhofen Limestone and Comiso Limestone) have shown the importance of temperature, and the presence of water as pore fluid, on the mechanical strength and failure mode of the rocks. However, to our knowledge, no previous studies have considered the distal heating effect of intrusions on the carbonate mechanical strength from the basement. Here we investigate the behaviour under varying P-T conditions at constant strain rate (10-5 s-1) on both dry and water saturated samples of Comiso Limestone, a low-porosity (10.2% average) carbonate rock belonging to the HP. We ran separate conventional triaxial experiments at various confining effective pressure from 0 up to 50 MPa at room temperature (20°C), in both dry and drained water-saturated conditions, using natural samples, and thermally-treated samples (150°C, 300°C, and 450°C). Acoustic Emissions and P-wave velocities were recorded during the experiments. Sample failure covers the brittle and

  18. Preliminary findings radon daughter levels in structures constructed on reclaimed Florida phosphate land

    International Nuclear Information System (INIS)

    1975-09-01

    Preliminary results are reported from a survey of the radon daughter levels in structures in Polk County, Florida, built on reclaimed phosphate tailings containing various amounts of 226 Ra. The structures surveyed consisted primarily of private dwellings although a few office buildings were also surveyed. Track-etch films and TLD air samplers were used to measure the levels of radon daughters within the structures and in structures built on non-phosphate land. Radiation levels were converted to WL units (the working level (WL) unit is defined as the potential α energy from the short-lived daughters of Rn which will produce 1.3 x 10 5 MeV in one liter of air). The highest observed level in any structure was 0.2 WL. Possible health hazards to long-time occupants are discussed

  19. Reclaiming the person: intersectionality and dynamic social categories through a psychological lens.

    Science.gov (United States)

    Frazier, Kathryn E

    2012-09-01

    Psychology's conventionally treatment of individuals' engagement with and resistance to the societal processes in which they are embedded has come under scrutiny amid the rise of postmodernist and critical feminist perspectives (among many others) in the social sciences. A sample of social psychology's responses to these critiques is presented in the recently published book, Social Categories in Everyday Experience edited by Shaun Wiley et al. (2011). In this essay, the challenges of seriously addressing the critiques of psychology's conventional treatment of social categories, which implicate fundamental assumptions of the discipline, are discussed. Further, it is argued that in order to effectively construct psychological accounts of political activism and social change amid theories that are increasingly cognizant of the complexities and contingencies of social embeddiness, the person must be reclaimed and revisioned. Notions of agency that complement an intersectional and systemic vision of the social world are discussed.

  20. Investigations of the Quality of the Reclaim of Spent Moulding Sands with Organic Binders

    Directory of Open Access Journals (Sweden)

    R. Dańko

    2012-09-01

    Full Text Available Modern investigation methods and equipment for the quality estimation of the moulding sands matrices with organic binders, in theircirculation process, are presented in the paper. These methods, utilising the special equipment combined with the authors investigationmethods developed in the Faculty of Foundry Engineering, AGH the University of Science and Technology, allow for the better estimationof the matrix quality. Moulding sands systems with organic binders require an in-depth approach to factors deciding on the matrixtechnological suitability as well as on their environmental impact. Into modern methods allowing for the better assessment of the matrixquality belongs the grain size analysis of the reclaimed material performed by means of the laser diffraction and also the estimation of the moulding sand gas evolution rate and identification of the emitted gases and their BTEX group gases content, since they are specially hazardous from the point of view of the Occupational Safety and Health.

  1. Economic Evaluation of the Juvenile Drug Court/Reclaiming Futures (JDC/RF) Model.

    Science.gov (United States)

    McCollister, Kathryn; Baumer, Pamela; Davis, Monica; Greene, Alison; Stevens, Sally; Dennis, Michael

    2018-07-01

    Juvenile drug court (JDC) programs are an increasingly popular option for rehabilitating juvenile offenders with substance problems, but research has found inconsistent evidence regarding their effectiveness and economic impact. While assessing client outcomes such as reduced substance use and delinquency is necessary to gauge program effectiveness, a more comprehensive understanding of program success and sustainability can be attained by examining program costs and economic benefits. As part of the National Cross-Site Evaluation of JDC and Reclaiming Futures (RF), an economic analysis of five JDC/RF programs was conducted from a multisystem and multiagency perspective. The study highlights the direct and indirect costs of JDC/RF and the savings generated from reduced health problems, illegal activity, and missed school days. Results include the average (per participant) cost of JDC/RF, the total economic benefits per JDC/RF participant, and the net savings of JDC/RF relative to standard JDC.

  2. Investigations of the Quality of The Reclaim of Spent Moulding Sands with Organic Binders

    Directory of Open Access Journals (Sweden)

    Dańko R.

    2012-09-01

    Full Text Available Modern investigation methods and equipment for the quality estimation of the moulding sands matrices with organic binders, in their circulation process, are presented in the paper. These methods, utilising the special equipment combined with the authors investigation methods developed in the Faculty of Foundry Engineering, AGH the University of Science and Technology, allow for the better estimation of the matrix quality. Moulding sands systems with organic binders require an in-depth approach to factors deciding on the matrix technological suitability as well as on their environmental impact. Into modern methods allowing for the better assessment of the matrix quality belongs the grain size analysis of the reclaimed material performed by means of the laser diffraction and also the estimation of the moulding sand gas evolution rate and identification of the emitted gases and their BTEX group gases content, since they are specially hazardous from the point of view of the Occupational Safety and Health.

  3. Post-treatment of reclaimed waste water based on an electrochemical advanced oxidation process

    Science.gov (United States)

    Verostko, Charles E.; Murphy, Oliver J.; Hitchens, G. D.; Salinas, Carlos E.; Rogers, Tom D.

    1992-01-01

    The purification of reclaimed water is essential to water reclamation technology life-support systems in lunar/Mars habitats. An electrochemical UV reactor is being developed which generates oxidants, operates at low temperatures, and requires no chemical expendables. The reactor is the basis for an advanced oxidation process in which electrochemically generated ozone and hydrogen peroxide are used in combination with ultraviolet light irradiation to produce hydroxyl radicals. Results from this process are presented which demonstrate concept feasibility for removal of organic impurities and disinfection of water for potable and hygiene reuse. Power, size requirements, Faradaic efficiency, and process reaction kinetics are discussed. At the completion of this development effort the reactor system will be installed in JSC's regenerative water recovery test facility for evaluation to compare this technique with other candidate processes.

  4. Delineation of submarine groundwater discharge (SGD) in a large-scaled reclaimed land

    Science.gov (United States)

    Lee, B.; Park, S.; Hwang, J.; Song, S.; Choi, J.; Nam, K.

    2010-12-01

    The Saemangeum reclaimed land in Korea is currently under construction for an eco-friendly multifunctional complex including agriculture, eco-tourism, business, and renewable energy industry. Regarding water supply for the reclaimed land, groundwater is the sustainable water resource and submarine groundwater discharge (SGD), subsurface fluids flowing from land to the sea, is considered as an alternative one. This study was conducted to identify SGD below a southeastern part of the reclaimed land and to delineate its pathway by investigating groundwater chemistry and electrical resistivity distribution of subsurface. Thirty four groundwater samples were collected from shallow agricultural wells placed along the past coast line (~5 km length) of the southeastern part in May and October, 2009. Field parameters including pH, EC, temperature, and ORP were measured using a portable multi-sensor and alkalinity by titration. They were analyzed for stable isotopes (δ18O and δ2H), cations (Na, K, Ca, Mg, Si, and NH4), anions (Cl, NO3, SO4, and PO4), and metals (Fe and Mn). Mean EC value was 1,163 µS/cm, corresponding to the appropriate crop growth because the criteria of crop yield is less 2,000 µS/cm. Stable isotopes results were plotted on the local meteoric water line, indicating lighter than those from sea water. It implied that the groundwater originated from inland precipitation and occurred as SGD along the coast line. From the groundwater compositions showing various water types including Na-HCO3, Ca-Cl, and Na-Cl, it could be concluded that small-scale SGD and seawater intrusion have great influences on the groundwater quality. From correlation analysis of EC-pH, Cl-HCO3, NO3-SO4, NO3-Cl, and (Fe, Mn)-NH4, spatial distributions of SGD were identified. A small catchment (0.2 km2) in the reclaimed land was selected to delineate a SGD flow path by two-dimensional electrical resistivity survey. The longitudinal and transverse lines were 760 and 275 m, respectively

  5. Ageing evolution of foamed warm mix asphalt combined with reclaimed asphalt pavement

    International Nuclear Information System (INIS)

    Perez-Martinez, M.; Marsac, P.; Gabet, T.; Pouget, S.; Hammoum, F.

    2017-01-01

    The combination of high rates of reclaimed asphalt pavement (RAP) and warm mix asphalt (WMA) technologies is still ambiguous in terms of durability. With the aim of clarifying this issue, a study comparing a hot mix asphalt with a WMA prepared using the foaming process technology. Both mixes contain 50% of RAP and are submitted to a laboratory ageing procedure. The long term related performance of the mixtures is compared by means of complex modulus and fatigue testing. Penetration and ring and ball tests are undertaken on the recovered bitumens, as well as the ageing evolution, characterised by the Fourier Transform Infrared analysis. Finally, the Apparent Molecular Weight Distribution (AMWD) of the binders is calculated from rheological measurements using the δ-method. Results show a relation between ageing evolution and mechanical performance. After ageing, the overall tendencies are similar for both processes. [es

  6. Managed aquifer recharge with reclaimed water: approaches to a European guidance framework.

    Science.gov (United States)

    Hochstrat, R; Wintgens, T; Kazner, C; Jeffrey, P; Jefferson, B; Melin, T

    2010-01-01

    Managed Aquifer Recharge (MAR) with reclaimed water plays a particular role in water stress mitigation, due to both the large potential benefits achieved in terms of sustainable water resources management as well as the complexity of the planning and implementation. This paper focuses on the role of policy in establishing water quality related legal frameworks that are crucial for MAR development. It analyses and compares the current practice of shaping boundary conditions, particularly in a European context but with some international comparison. The work reports on the legal aspects considered most relevant for MAR in the European Union and summarises issues addressed in aquifer recharge regulations and guidelines. Some potential actions are proposed to develop a suitable guidance framework for further exploitation of MAR benefits.

  7. Assessment of the viability of using saline reclaimed water in grapefruit in medium to long term

    Directory of Open Access Journals (Sweden)

    Cristina Romero-Trigueros

    2014-11-01

    Full Text Available Citrus trees are strongly affected by salinity, especially in countries where irrigation is required as a semi-arid Mediterranean agronomic region. The aims of the study were i to identify the best reliable plant-based water status indicator for field grown grapefruit trees irrigated with saline reclaimed water during five years of cultivation by measuring seasonal changes in physiological parameters (i.e. gas exchange and stem water potential measurements, leaf structural traits (i.e. leaf chlorophyll content, area-based leaf nitrogen and area-based dry mass, phytotoxic elements and yield; ii to estimate phytotoxicity thresholds at leaf level. Our results showed that the chlorophyll content was the parameter with the highest number of measures with significant differences (p≤0.05, ANOVA between trees irrigated with reclaimed water and control trees throughout growing stages. Moreover, Chl a increased linearly with area-based leaf nitrogen (R2=0.63; p<0.001 and area-based dry mass (R2=0.64; p<0.001. We also determined the salt-induced phytotoxicity thresholds at which a reduction in yields occurs; these levels were Na: 0.1 g/100 g, Cl: 0.6 g/100 gand B: 100 ppm. In conclusion, we revealed the importance of leaf chlorophyll measurements as a significance diagnostic indicator of salt stress on field grown grapefruit trees. This parameter was also related to plant-based water status indicators such as stem water potential, stomatal conductance and net photosynthesis. Additionally, a salt accumulation potential at leaf level was shown, leading to possible risk in crop sustainability in the medium to long term.

  8. Estimation of possibilities of making euro pallets from reclaimed polyolefin’s with tuff

    Directory of Open Access Journals (Sweden)

    S. Kuciel

    2010-07-01

    Full Text Available Possibilities of reusing and developing of waste plastics are one of the main problems of waste management for municipal governmentespecially in the context of adapting Polish law to standards of EC [1]. During the last 10 years total amount of plastics waste increasedtwice, especially in communal agglomerations. Among communal waste plastics make up 7 to 14% of whole their mass and 30% of theirvolume [1,2]. Plastic products have been recycled to be used in a number of different products often different from their original use.Reclaimed plastics can’t be used as products which have contact with food or as high demands esthetic and hygienic products, they alsoshouldn’t be applied as short-time used products because they quickly come back to plastics store-place. Reclaimed plastics have lowerproperties than virgin plastics – mainly the strength falls with the simultaneous fall of modules and increase fragile especially for PP, PE,PS and PET [1]. One of the possibilities of reinforcement of polyolefines is adding diverse fillers like glass or carbon fibers (but they arerather expensive and natural fillers like mineral, wood and others [3]. It’s especially important for wasted of low density polyethylenewhich has low modulus. For the tests it was used waste polyethylene (LDPE and HDPE from industrial with 15% mineral fillers – tuff.For the tests it was prepared two kinds of composites materials with 15% of tuff powder. Besides for comparison it was tested recycledpolyethylene (HDPE and LDPE and next was tested specimens cut out from produced europallets (with 15% of tuff. It was testedmechanical properties all prepared composite materials like tensile strength, stress and bending e-modulus and processing properties likemelt flow, Vicat point and photos on SEM microscope.

  9. Spatial variation in spoil and vegetative characteristics of pastures on reclaimed surface mined land

    International Nuclear Information System (INIS)

    Teutsch, C.D.; Collins, M.; Ditsch, D.C.

    1999-01-01

    Kentucky has large areas of reclaimed surface mined land that could provide grazing for livestock. Research is needed to determine optimal stocking densities and to evaluate the sustainability of such grazing systems for this region. A long-term grazing study was initiated in 1997 on 151 ha of reclaimed land near Chavies, KY to determine spatial and temporal variation with stocking densities of 0, 0.28, 0.42, or 0.83 beef cow-calf units/ha. Global Positioning System and GIS technologies were used to establish pasture boundaries, locate permanent sampling markers at a density of 1 per 0.4 ha, and interpolate maps of physical, spoil, and vegetable pasture characteristics. Herbage and spoil samples were collected around the permanent markers in May of 1997. Stepwise regression was used to determine factors affecting the vegetative characteristics of the sites. Biomass density ranged from 0 to 2500 kg/ha with a mean of 570 kg/ha. Factors affecting biomass included legume and weed proportions in the sward, grazing activity, soil potassium, elevation, and potential acidity, cumulatively accounting for 32% of the variation. Ground cover ranged from 10 to 100% with an average of 74%. Soil pH, potassium, and grass in the sward accounted for 14% of the variation in ground cover. Legumes made up 0 to 61% of the sward with a mean of 13% over the pasture area. Variables affecting the amount of legume in the sward included biomass density, slope, elevation, pH, and stocking density, together accounting for 21% of the variation. Spatial variation in the physical, spoil, and vegetative characteristics of the pastures was large. Overall, regression accounted for a limited amount of the variation in the vegetative characteristics of the site indicating that other important variables exist

  10. Impacts of reclaimed water irrigation on soil antibiotic resistome in urban parks of Victoria, Australia.

    Science.gov (United States)

    Han, Xue-Mei; Hu, Hang-Wei; Shi, Xiu-Zhen; Wang, Jun-Tao; Han, Li-Li; Chen, Deli; He, Ji-Zheng

    2016-04-01

    The effluents from wastewater treatment plants have been recognized as a significant environmental reservoir of antibiotics and antibiotic resistance genes (ARGs). Reclaimed water irrigation (RWI) is increasingly used as a practical solution for combating water scarcity in arid and semiarid regions, however, impacts of RWI on the patterns of ARGs and the soil bacterial community remain unclear. Here, we used high-throughput quantitative PCR and terminal restriction fragment length polymorphism techniques to compare the diversity, abundance and composition of a broad-spectrum of ARGs and total bacteria in 12 urban parks with and without RWI in Victoria, Australia. A total of 40 unique ARGs were detected across all park soils, with genes conferring resistance to β-lactam being the most prevalent ARG type. The total numbers and the fold changes of the detected ARGs were significantly increased by RWI, and marked shifts in ARG patterns were also observed in urban parks with RWI compared to those without RWI. The changes in ARG patterns were paralleled by a significant effect of RWI on the bacterial community structure and a co-occurrence pattern of the detected ARG types. There were significant and positive correlations between the fold changes of the integrase intI1 gene and two β-lactam resistance genes (KPC and IMP-2 groups), but no significant impacts of RWI on the abundances of intI1 and the transposase tnpA gene were found, indicating that RWI did not improve the potential for horizontal gene transfer of soil ARGs. Taken together, our findings suggested that irrigation of urban parks with reclaimed water could influence the abundance, diversity, and compositions of a wide variety of soil ARGs of clinical relevance. Irrigation of urban parks with treated wastewater significantly increased the abundance and diversity of various antibiotic resistance genes, but did not significantly enhance their potential for horizontal gene transfer. Copyright © 2015 Elsevier

  11. The effect of reclaimed wastewater on the quality and growth of grapevines.

    Science.gov (United States)

    Mendoza-Espinosa, L G; Cabello-Pasini, A; Macias-Carranza, V; Daessle-Heuser, W; Orozco-Borbón, M V; Quintanilla-Montoya, A L

    2008-01-01

    The effect of the use of treated wastewater on the growth of cabernet sauvignon and merlot grapes from the Guadalupe Valley, Mexico was evaluated. Secondary advanced effluent was used to irrigate the grapevines at a rate of 66 L/vine/week. Wastewater quality results confirmed that all parameters complied with Mexican legislation for crop irrigation as well as reuse in activities in which the public would be in direct or indirect contact with the reclaimed water. Results showed that the number of leaves per shoot and the overall biomass increased in plants irrigated with wastewater and grape production per plant was 20% higher. The concentration of carbohydrates, organic acids and pH were similar in grapes from vines irrigated with wastewater to those irrigated with groundwater. Throughout the experiment, no fecal coliform bacteria were detected in the cultivated grapes. The wastewater caused an increase in the biomass of the grapevines and there was no presence of microbial indicators in the final product so a higher wine production could be achieved without an increase in health risk related problems. If 200 L/s of reclaimed wastewater would be returned to be used for grapevine irrigation in Valle de Guadalupe (the same amount that is currently being sent as drinking water to Ensenada), assuming an irrigation application of 6,000-7.500 m3/ha/year, approximately 837-1046 hectares (ha) of grapevines could be irrigated. Part of ongoing research includes an economical analysis of the best options for Ensenada and the Valle de Guadalupe in order to establish the optimum volume of water to be returned, the cost of its transportation, as well as the cost of irrigation. (c) IWA Publishing 2008.

  12. Environmental insecticide residues from tsetse fly control measures in Uganda

    International Nuclear Information System (INIS)

    Sserunjoji-Sebalija, J.

    1976-01-01

    Up to June 1974 areas in Uganda totalling 8600km 2 have been successfully reclaimed from tsetse fly infestation by ground spray of 3% dieldrin water emulsions. A search for equally effective but less persistent and toxic compounds against tsetse flies has been unsuccessful. Fourteen insecticide formulations have been tested for their persistence on tree bark surfaces and, therefore, their availability and toxicity to the target tsetse flies. Only those compounds with a high immediate insecticidal activity (some higher than dieldrin) like endosulfan, Chlorfenvinphos and propoxur could merit further consideration in tsetse control. While some were toxic to tsetse as fresh deposits, they lacked sufficient persistence. A study of the environmental implication from the continued use of the highly persistent and toxic dieldrin has provided useful data on residues likely to be found both in terrestrial and aquatic fauna and flora. These are generally low. Moreover, there is evidence of degradation in some fish species (Protopterus aethiopicus and Clarias). Also, dilution factors and adsorption involving the muddy nature of water run-off, etc., and controlled burning of grasses after tsetse eradication would tend to inactivate the residual insecticide and protect aquatic systems. The general findings have indicated less risk than anticipated of the environmental contamination from tsetse control by application of persistent and toxic insecticides. (author)

  13. Screening of emerging contaminants and priority substances (2008/105/EC) in reclaimed water for irrigation and groundwater in a volcanic aquifer (Gran Canaria, Canary Islands, Spain).

    Science.gov (United States)

    Estévez, Esmeralda; Cabrera, María del Carmen; Molina-Díaz, Antonio; Robles-Molina, José; Palacios-Díaz, María del Pino

    2012-09-01

    In semiarid regions, reclaimed water can be an important source of emerging pollutants in groundwater. In Gran Canaria Island, reclaimed water irrigation has been practiced for over thirty years and currently represents 8% of water resources. The aim of this study was to monitor contaminants of emerging concern and priority substances (2008/105/EC) in a volcanic aquifer in the NE of Gran Canaria where the Bandama Golf Course has been sprinkled with reclaimed water since 1976. Reclaimed water and groundwater were monitoring quarterly from July 2009 to May 2010. Only 43% of the 183 pollutants analysed were detected: 42 pharmaceuticals, 20 pesticides, 12 polyaromatic hydrocarbons, 2 volatile organic compounds and 2 flame retardants. The most frequent compounds were caffeine, nicotine, chlorpyrifos ethyl, fluorene, phenanthrene and pyrene. Concentrations were always below 50 ng L(-1), although some pharmaceuticals and one pesticide, cholrpyrifos ethyl, were occasionally detected at higher concentrations. This priority substance for surface water exceeded the maximum threshold (0.1 μg L(-1)) for pesticide concentration in groundwater (2006/118/EC). Sorption and degradation processes in soil account for more compounds being detected in reclaimed water than in groundwater, and that some contaminants were always detected in reclaimed water, but never in groundwater (flufenamic acid, propyphenazone, terbutryn and diazinon). Furthermore, erythromycin was always detected in reclaimed water (exceeding occasionally 0.1 μg L(-1)), and was detected only once in groundwater. In contrast, some compounds (phenylephrine, nifuroxazide and miconazole) never detected in reclaimed water, were always detected in groundwater. This fact and the same concentration range detected for the groups, regardless of the water origin, indicated alternative contaminant sources (septic tanks, agricultural practices and sewerage breaks). The widespread detection of high adsorption potential compounds

  14. Characterization of reclaimed GaAs substrates and investigation of reuse for thin film InGaAlP LED epitaxial growth

    Energy Technology Data Exchange (ETDEWEB)

    Englhard, M.; Klemp, C.; Behringer, M.; Rudolph, A. [OSRAM Opto Semiconductors GmbH, Leibnizstr. 4, 93055 Regensburg (Germany); Skibitzki, O.; Zaumseil, P. [IHP, Im Technologiepark 25, 15236 Frankfurt (Oder) (Germany); Schroeder, T. [IHP, Im Technologiepark 25, 15236 Frankfurt (Oder) (Germany); Institute of Physics and Chemistry, BTU Cottbus-Senftenberg, Konrad-Zuse-Str. 1, 03046 Cottbus (Germany)

    2016-07-28

    This study reports a method to reuse GaAs substrates with a batch process for thin film light emitting diode (TF-LED) production. The method is based on an epitaxial lift-off technique. With the developed reclaim process, it is possible to get an epi-ready GaAs surface without additional time-consuming and expensive grinding/polishing processes. The reclaim and regrowth process was investigated with a one layer epitaxial test structure. The GaAs surface was characterized by an atomic force microscope directly after the reclaim process. The crystal structure of the regrown In{sub 0.5}(Ga{sub 0.45}Al{sub 0.55}){sub 0.5}P (Q{sub 55}) layer was investigated by high resolution x-ray diffraction and scanning transmission electron microscopy. In addition, a complete TF-LED grown on reclaimed GaAs substrates was electro-optically characterized on wafer level. The crystal structure of the epitaxial layers and the performance of the TF-LED grown on reclaimed substrates are not influenced by the developed reclaim process. This process would result in reducing costs for LEDs and reducing much arsenic waste for the benefit of a green semiconductor production.

  15. Effects of middle-term land reclamation on nickel soil-water interaction: a case study from reclaimed salt marshes of Po River Delta, Italy.

    Science.gov (United States)

    Di Giuseppe, Dario; Melchiorre, Massimiliano; Faccini, Barbara; Ferretti, Giacomo; Coltorti, Massimo

    2017-09-26

    Reclaimed salt marshes are fragile environments where water salinization and accumulation of heavy metals can easily occur. This type of environment constitutes a large part of the Po River Delta (Italy), where intensive agricultural activities take place. Given the higher Ni background of Po River Delta soils and its water-soluble nature, the main aim of this contribution is to understand if reclamation can influence the Ni behavior over time. In this study, we investigated the geochemical features of 40 soils sampled in two different localities from the Po River Delta with different reclamation ages. Samples of salt marsh soils reclaimed in 1964 were taken from Valle del Mezzano while soils reclaimed in 1872 were taken nearby Codigoro town. Batch solubility tests and consecutive determination of Ni in pore-water were compared to bulk physicochemical compositions of soils. Bulk Ni content of the studied soils is naturally high, since these soils originated from Po River sediments derived from the erosion of ultramafic rocks. Moreover, it seems that Ni concentration increases during soil evolution, being probably related to the degradation of serpentine. Instead, the water-soluble Ni measured in the leaching tests is greater in soils recently reclaimed compared to the oldest soils. Soil properties of two soil profiles from a reclaimed wetland area were examined to determine soil evolution over one century. Following reclamation, pedogenic processes of the superficial horizons resulted in organic matter mineralization, pH buffer, and a decrease of Ni water solubility from recently to evolved reclaimed soil.

  16. Handling of Solid Residues

    International Nuclear Information System (INIS)

    Medina Bermudez, Clara Ines

    1999-01-01

    The topic of solid residues is specifically of great interest and concern for the authorities, institutions and community that identify in them a true threat against the human health and the atmosphere in the related with the aesthetic deterioration of the urban centers and of the natural landscape; in the proliferation of vectorial transmitters of illnesses and the effect on the biodiversity. Inside the wide spectrum of topics that they keep relationship with the environmental protection, the inadequate handling of solid residues and residues dangerous squatter an important line in the definition of political and practical environmentally sustainable. The industrial development and the population's growth have originated a continuous increase in the production of solid residues; of equal it forms, their composition day after day is more heterogeneous. The base for the good handling includes the appropriate intervention of the different stages of an integral administration of residues, which include the separation in the source, the gathering, the handling, the use, treatment, final disposition and the institutional organization of the administration. The topic of the dangerous residues generates more expectation. These residues understand from those of pathogen type that are generated in the establishments of health that of hospital attention, until those of combustible, inflammable type, explosive, radio-active, volatile, corrosive, reagent or toxic, associated to numerous industrial processes, common in our countries in development

  17. Influence of humic substances on electrochemical degradation of trichloroethylene in limestone aquifers

    International Nuclear Information System (INIS)

    Rajic, Ljiljana; Fallahpour, Noushin; Nazari, Roya; Alshawabkeh, Akram N.

    2015-01-01

    Highlights: • Humic substances (HS) adversely affect TCE electrochemical reduction. • The inverse correlation between HS content and TCE removal is linear. • HS interfere with the hydrodechlorination of TCE at the cathode. • The impact of HS on TCE removal was reduced in the presence of limestone gravel. - Abstract: In this study we investigate the influence of humic substances (HS) on electrochemical transformation of trichloroethylene (TCE) in groundwater from limestone aquifers. A laboratory flow-through column with an electrochemical reactor that consists of a palladized iron foam cathode followed by a MMO anode was used to induce TCE electro-reduction in groundwater. Up to 82.9% TCE removal was achieved in the absence of HS. Presence of 1, 2, 5, and 10 mgTOC L −1 reduced TCE removal to 70.9%, 61.4%, 51.8% and 19.5%, respectively. The inverse correlation between HS content and TCE removal was linear. Total organic carbon (TOC), dissolved organic carbon (DOC) and absorption properties (A = 254 nm, 365 nm and 436 nm) normalized to DOC, were monitored during treatment to understand the behavior and impacts of HS under electrochemical processes. Changes in all parameters occurred mainly after contact with the cathode, which implies that the HS are reacting either directly with electrons from the cathode or with H 2 formed at the cathode surface. Since hydrodechlorination is the primary TCE reduction mechanism in this setup, reactions of the HS with the cathode limit transformation of TCE. The presence of limestone gravel reduced the impact of HS on TCE removal. The study concludes that presence of humic substances adversely affects TCE removal from contaminated groundwater by electrochemical reduction using palladized cathodes.

  18. Incorporating full-scale experience into advanced limestone wet FGD designs

    International Nuclear Information System (INIS)

    Rader, P.C.; Bakke, E.

    1992-01-01

    Utilities choosing flue gas desulfurization as a strategy for compliance with Phase I of the 1990 Clean Air Act Amendments will largely turn to limestone wet scrubbing as the most cost-effective, least-risk option. State-of-the-art single absorber wet scrubbing systems can be designed to achieve: SO 2 removal efficiencies in excess of 95 %, system availabilities in excess of 98%, and byproducts which can be marketed or land filled. As a result of varying fuel characteristics, site considerations, and owner preferences, FGD plants for large central power stations are typically custom-designed. To avoid the risks associated with new, first-of-a-kind technologies, utilities have preferred to purchase FGD systems from suppliers with proven utility experience and reference plants as close as possible to the design envisioned. As the market for FGD systems is regulatory driven, the demand has shifted geographically in response to national environmental policies. Although limestone wet scrubbing has emerged as the overwhelming choice for SO 2 emission control in coal-fired power stations, the technology has evolved and been adapted to suit local and regional technical and economic situations. Global suppliers are able to benefit from experience and technological advances in the world market. With market units in the U.S., Denmark, Italy, Sweden, and Germany active in the design and supply of wet FGD plants, ABB has a unique ability to incorporate knowledge and experience gained throughout the industrialized world to acid rain retrofit projects in the U.S. This paper describes the design of advanced limestone wet scrubbing systems for application to acid rain retrofits. Specifically, the evolution of advanced design concepts from a global experience base is discussed

  19. Soluble salt sources in medieval porous limestone sculptures: A multi-isotope (N, O, S) approach

    Energy Technology Data Exchange (ETDEWEB)

    Kloppmann, W., E-mail: w.kloppmann@brgm.fr [BRGM, Direction des Laboratoires, Unité Isotopes, BP 6009, F-45060 Orléans cedex 2 (France); Rolland, O., E-mail: olivierrolland@wanadoo.fr [Montlouis-sur-Loire (France); Proust, E.; Montech, A.T. [BRGM, Direction des Laboratoires, Unité Isotopes, BP 6009, F-45060 Orléans cedex 2 (France)

    2014-02-01

    The sources and mechanisms of soluble salt uptake by porous limestone and the associated degradation patterns were investigated for the life-sized 15th century “entombment of Christ” sculpture group located in Pont-à-Mousson, France, using a multi-isotope approach on sulphates (δ{sup 34}S and δ{sup 18}O) and nitrates (δ{sup 15}N and δ{sup 18}O). The sculpture group, near the border of the Moselle River, is within the potential reach of capillary rise from the alluvial aquifer. Chemical analyses show a vertical zonation of soluble salts with a predominance of sulphates in the lower parts of the statues where crumbling and blistering prevail, and higher concentrations of nitrates and chloride in the high parts affected by powdering and efflorescence. Isotope fingerprints of sulphates suggest a triple origin: (1) the lower parts are dominated by capillary rise of dissolved sulphate from the Moselle water with characteristic Keuper evaporite signatures that progressively decreases with height; (2) in the higher parts affected by powdering the impact of atmospheric sulphur becomes detectable; and (3) locally, plaster reparations impact the neighbouring limestone through dissolution and re-precipitation of gypsum. Nitrogen and oxygen isotopes suggest an organic origin of nitrates in all samples. N isotope signatures are compatible with those measured in the alluvial aquifer of the Moselle River further downstream. This indicates contamination by sewage or organic fertilisers. Significant isotopic contrasts are observed between the different degradation features depending on the height and suggest historical changes of nitrate sources. - Highlights: • We use S, N and O isotopes to distinguish salt sources in limestone sculptures. • Vertical zonation of degradation is linked to capillary rise and air pollution. • Sulphate salts in lower parts are derived from river/groundwater. • Sulphate salts in higher parts show signature of air pollution. • Nitrates

  20. Evaluating macroinvertebrate community shifts in the confluence of freestone and limestone streams

    Directory of Open Access Journals (Sweden)

    Jennifer K. Hellmann

    2014-07-01

    Full Text Available Aquatic macroinvertebrates are critical to ecosystem functioning through their regulation of many essential top-down and bottom-up ecosystem processes such as energy translocation, nutrient flow, and detrital decomposition. However, specific preferences by macroinvertebrates for certain ranges of abiotic and biotic characteristics mean that changes in these factors often create large differences in benthic community structure. Investigations into drivers of community structure have found distinct patterns of variation between ecosystems, but drivers of macroscale variation may differ from drivers of microscale variation. Such microscale variation in macroinvertebrate community structure as a function of abiotic conditions may be found in the confluence of two geologically distinct freshwater streams. Variation in the origin, underlying bedrock, and watershed of a stream results in drastically different physical and chemical characteristics and correspondingly distinct macroinvertebrate community structures. In areas where water from geologically distinct streams flows together, a mixing zone emerges with unique chemical and physical characteristics. There is little information on how invertebrate communities are structured within this mixing zone. To investigate this, we examined how the structure of the macroinvertebrate community changed downstream of the confluence. Up to thirty metres downstream, we found distinct stream sections that mirrored physical and chemical conditions found in limestone and freestone streams, and a mixing zone with emergent properties. These physical and chemical changes between sites were accompanied by shifts in macroinvertebrate community composition. Diversity indices indicated significantly higher diversity in freestone sites than in limestone sites or the mixing zone and there was a unique composition of genera in the mixing zone that were distinct from both limestone and freestone sites. Factors driving

  1. Wet separation processes as method to separate limestone and oil shale

    Science.gov (United States)

    Nurme, Martin; Karu, Veiko

    2015-04-01

    Biggest oil shale industry is located in Estonia. Oil shale usage is mainly for electricity generation, shale oil generation and cement production. All these processes need certain quality oil shale. Oil shale seam have interlayer limestone layers. To use oil shale in production, it is needed to separate oil shale and limestone. A key challenge is find separation process when we can get the best quality for all product types. In oil shale separation typically has been used heavy media separation process. There are tested also different types of separation processes before: wet separation, pneumatic separation. Now oil shale industry moves more to oil production and this needs innovation methods for separation to ensure fuel quality and the changes in quality. The pilot unit test with Allmineral ALLJIG have pointed out that the suitable new innovation way for oil shale separation can be wet separation with gravity, where material by pulsating water forming layers of grains according to their density and subsequently separates the heavy material (limestone) from the stratified material (oil shale)bed. Main aim of this research is to find the suitable separation process for oil shale, that the products have highest quality. The expected results can be used also for developing separation processes for phosphorite rock or all others, where traditional separation processes doesn't work property. This research is part of the study Sustainable and environmentally acceptable Oil shale mining No. 3.2.0501.11-0025 http://mi.ttu.ee/etp and the project B36 Extraction and processing of rock with selective methods - http://mi.ttu.ee/separation; http://mi.ttu.ee/miningwaste/

  2. Assessment of Rock Slope Stability in Limestone Quarries in the Tournai's Region (Belgium) Using Structural Data

    Science.gov (United States)

    Tshibangu, Jean-Pierre; Deloge, K. Pierre-Alexandre; Deschamps, Benoît; Coudyzer, Christophe

    The Tournais region is characterised by famous outcrops of carboniferous limestone which is mined out for cement and raw material production. The four main quarries found in the Region, i.e. Gaurain-Ramecroix, Milieu, Antoing and Lemay; are owned by the three main cement producers in Belgium: Italcimenti, Holcim and CBR. The global production of limestone is about 20 millions tons per year, giving big pits with depths up to 150 m. With the growth of the pits, the quarries are approaching each other leading to the problem of managing the reserves contained in the separating walls and their mechanical stability. The limestone deposit is composed of different seams having varying thickness, chemical com- position and even mechanical properties. The deposit has an overall horizontal dip and is intersected by two main sets of discontinuities with a spacing of about 10 m or less. It is also crossed by a set of east to west faults but the quarries are implanted in the in between areas, so to not be crossed by these faults. The layers and specially the shallow ones are characterised by a typical karstic weathering giving open or filled cavities. This paper presents the global work quarried out in order to study the stability of the Lemays quarry. First a description of the orientation and spacing of discontinuities is presented, and an attempt made to correlate to the development of weathering. Mechanical laboratory tests have been performed and a qualification of the rock mass assessed. A coupled approach is then presented using a mining planning analysis and mechanical simulation (i.e. Finite Element method).

  3. Estimation of deep infiltration in unsaturated limestone environments using cave lidar and drip count data

    Science.gov (United States)

    Mahmud, K.; Mariethoz, G.; Baker, A.; Treble, P. C.; Markowska, M.; McGuire, E.

    2016-01-01

    Limestone aeolianites constitute karstic aquifers covering much of the western and southern Australian coastal fringe. They are a key groundwater resource for a range of industries such as winery and tourism, and provide important ecosystem services such as habitat for stygofauna. Moreover, recharge estimation is important for understanding the water cycle, for contaminant transport, for water management, and for stalagmite-based paleoclimate reconstructions. Caves offer a natural inception point to observe both the long-term groundwater recharge and the preferential movement of water through the unsaturated zone of such limestone. With the availability of automated drip rate logging systems and remote sensing techniques, it is now possible to deploy the combination of these methods for larger-scale studies of infiltration processes within a cave. In this study, we utilize a spatial survey of automated cave drip monitoring in two large chambers of Golgotha Cave, south-western Western Australia (SWWA), with the aim of better understanding infiltration water movement and the relationship between infiltration, stalactite morphology, and unsaturated zone recharge. By applying morphological analysis of ceiling features from Terrestrial LiDAR (T-LiDAR) data, coupled with drip time series and climate data from 2012 to 2014, we demonstrate the nature of the relationships between infiltration through fractures in the limestone and unsaturated zone recharge. Similarities between drip rate time series are interpreted in terms of flow patterns, cave chamber morphology, and lithology. Moreover, we develop a new technique to estimate recharge in large-scale caves, engaging flow classification to determine the cave ceiling area covered by each flow category and drip data for the entire observation period, to calculate the total volume of cave discharge. This new technique can be applied to other cave sites to identify highly focussed areas of recharge and can help to better

  4. Assessing the Sensitivity of Mountain Forests to Site Degradation in the Northern Limestone Alps, Europe

    Directory of Open Access Journals (Sweden)

    Birgit Reger

    2015-05-01

    Full Text Available Because of some land-use practices (such as overstocking with wild ungulates, historical clear-cuts for mining, and locally persisting forest pasture, protective forests in the montane vegetation belt of the Northern Limestone Alps are now frequently overaged and poorly structured over large areas. Windthrow and bark beetle infestations have generated disturbance areas in which forests have lost their protective functions. Where unfavorable site conditions hamper regeneration for decades, severe soil loss may ensue. To help prioritize management interventions, we developed a geographic information system-based model for assessing sensitivity to site degradation and applied it to 4 test areas in the Northern Limestone Alps of Austria and Bavaria. The model consists of (1 analysis of site conditions and forest stand structures that could increase sensitivity to degradation, (2 evaluation of the sensitivity of sites and stands, and (3 evaluation and mapping of mountain forests' sensitivity to degradation. Site conditions were modeled using regression algorithms with data on site parameters from pointwise soil and vegetation surveys as responses and areawide geodata on climate, relief, and substrate as predictors. The resulting predictor–response relationships were applied to test areas. Stand structure was detected from airborne laser scanning data. Site and stand parameters were evaluated according to their sensitivity to site degradation. Sensitivities of sites and stands were summarized in intermediate-scale sensitivity maps. High sensitivity was identified in 3 test areas with pure limestone and dolomite as the prevailing sensitivity level. Moderately sensitive forests dominate in the final test area, Grünstein, where the bedrock in some strata contains larger amounts of siliceous components (marl, mudstone, and moraines; degraded and slightly sensitive forests were rare or nonexistent in all 4 test areas. Providing a comprehensive overview

  5. Bedrock stability in southeastern Sweden. Evidence from fracturing in the ordovician limestones of northern Oeland

    International Nuclear Information System (INIS)

    Milnes, A.G.; Gee, D.G.

    1992-09-01

    The stability of the bedrock in SE Sweden with regard to radioactive waste disposal has recently been the subject of some controversy. In order to better assess the age and significance of fracturing in the Precambrian basement at the site of the Aespoe Hard Rock Laboratory (HRL), near Oskarshamn, a detailed analysis of fracturing in the lower Ordovician limestones exposed along the west coast of the neighbouring island of Oeland has been carried out. The limestones form continuously exposed shore platforms, in segments up to 30 m broad and several kilometres long. These, and numerous quarries, provide ideal objects for quantitative analysis (ground and air photo mapping, scanline logging), and unique opportunities for investigating the amount of movement on the fractures, because of well-developed bedding and abundant rod-shaped fossils on the bedding surfaces. The fracture patterns are dominated by two sets of subvertical fractures, a NW trending closely spaced and strongly orientated set and a NNE-ENE trending widely spaced and variably orientated set. Only about 10% of the fractures in both sets show lateral fossil displacement, with maximum movement of 5 cm, and only 3% of the fractures show vertical displacement of bedding (maximum 8 cm). All in all, the lower Ordovician limestones along the exposed shoreline have suffered remarkably little deformation since deposition, i.e. over the last 500 million years. Appreciable bedrock instability, if it occurred, must have been concentrated offshore, or in the unexposed segments of the coastline, where some weak indications of slight movement (changes of a few metres in stratigraphic level) have been observed. Among other recommendations for further work, geophysical investigations to test these indications are suggested. (54 refs.)

  6. Biological nitrogen removal using soil columns for the reuse of reclaimed water: Performance and microbial community analysis.

    Science.gov (United States)

    Sun, Jiaji; Chen, Lei; Rene, Eldon R; Hu, Qian; Ma, Weifang; Shen, Zhenyao

    2018-07-01

    The main aim of this study was to remove nitrogen compounds from reclaimed water and reuse the water in semi-arid riverine lake systems. In order to assess the nitrogen removal efficiencies in different natural environments, laboratory scale column experiments were performed using sterilized soil (SS), silty clay (SC), soil with submerged plant (SSP) and biochar amendment soil (BCS). The initial concentration of NO 3 - -N and the flow rate was maintained constant at 15 mg L -1 and 0.6 ± 0.1 m d -1 , respectively. Among the tested columns, both SSP and BCS were able to achieve NO 3 - -N levels <0.2 mg L -1 in the treated reclaimed water. The results from bacterial community structure analysis, using 454 pyrosequencing of 16s rRNA genes, showed that the dominant denitrifier was Bacillus at the genera level. Copyright © 2018 Elsevier Ltd. All rights reserved.

  7. Modelling of limestone injection for SO2 capture in a coal fired utility boiler

    International Nuclear Information System (INIS)

    Kovacik, G.J.; Reid, K.; McDonald, M.M.; Knill, K.

    1997-01-01

    A computer model was developed for simulating furnace sorbent injection for SO 2 capture in a full scale utility boiler using TASCFlow TM computational fluid dynamics (CFD) software. The model makes use of a computational grid of the superheater section of a tangentially fired utility boiler. The computer simulations are three dimensional so that the temperature and residence time distribution in the boiler could be realistically represented. Results of calculations of simulated sulphur capture performance of limestone injection in a typical utility boiler operation were presented

  8. COPROLITES FROM THE DANIAN LIMESTONE (LOWER PALEOCENE) OF FAXE QUARRY, DENMARK

    DEFF Research Database (Denmark)

    Milàn, Jesper

    2010-01-01

    are attributed to sharks, and large, cylindrical coprolites with longitudinal striations on the surface are identified as crocodile coprolites. Fish and sharks are known from abundant finds of otoliths and teeth in Faxe Quarry, and crocodiles are known from finds of single bones and teeth.......A collection of coprolites found in the Danian (Lower Paleocene) limestone of Faxe Quarry, Denmark, is described and attributed to the respective producers. Small, drop-like specimens with weak signs of spiral coiling are attributed to fish. Larger, heteropolar, spirally-coiled specimens...

  9. Sponge assemblage of some Upper Permian reef limestones from Phrae province (Northern Thailand

    Directory of Open Access Journals (Sweden)

    Baba Senowbari-Daryan

    1994-12-01

    Full Text Available The sponge fauna of uppermost Permian reef or reefal limestones of the Phrae province in northern Thailand include representatives of hexactinellida, sclerospongea,"sphinctozoans", and "inozoans". The "sphinctozoans" and "inozoans"are described in detail. Following taxa are new:"Sphinctozoans": Phraethalamia tubulara n. gen., n. sp., Ambithalamia pérmican. gen., n. sp."Inozoans": Bisiphonella tubulara n. sp., Solutossaspongia crassimuralis n.gen., n. sp.The genus name Belyaevaspongia nom. nov. is proposed for PolysiphonellaBelyaeva, 1991 (in Boiko et al., 1991, non Polysiphonella Russo, 1981.

  10. Characteristics of a calcite "limestone"-marble from Macedonia, used as flux material

    Directory of Open Access Journals (Sweden)

    Hristova E.

    2003-01-01

    Full Text Available The phase characteristics of calcite "limestone"-marble from Banjany area village (near Skopje, Macedonia were examined by means of XRD, SEM microscope in polarizing and reflected lights, chemical, DT/TG-analyses. It was concluded as follows: - calcite (CaCO3 is a major mineral component (cca 80-90 % prevailing in the marble over the other minerals - dolomite is generally of minor importance (cca 10-20 % in the rock - quartz, micas graphite, pyrite represent typical accessories. As result of the mentioned phase characteristics, this raw materials was for a long time (more than 30 years used as flux in the iron and steel metallurgy in Macedonia.

  11. Three new species of Begonia (Begoniaceae from Limestone Hills in southwestern Sarawak, Borneo

    Directory of Open Access Journals (Sweden)

    Che-Wei Lin

    2017-04-01

    Full Text Available Most species of Begonia in Borneo, like those of other areas, are narrowly distributed and site-specific. In this study we report three new species of Begonia, namely B. felis C. W. Lin & C.-I Peng, B. kuchingensis C. W. Lin & C.-I Peng (sect. Petermannia and B. serianensis C. W. Lin & C.-I Peng (sect. Reichenheimia from the Padawan-Serian limestone hills in southwestern Sarawak. In addition to the taxonomic account, color plates, line drawings, a distribution map, and comparisons with phenetically similar species are provided to aid in identification.

  12. Haematological and physiological responses of brook charr, to untreated and limestone-neutralized acid mine drainage

    Energy Technology Data Exchange (ETDEWEB)

    Cole, M.B.; Arnold, D.E.; Watten, B.J.; Krise, W.F. [ABR Inc, Forest Grove, OR (USA). Environmental Research and Services

    2001-07-01

    Brook charr, Salvelinus fontinalis, exhibited depressed plasma sodium and elevated plasma glucose concentrations in untreated acid mine drainage effluent (AMD), at two dilutions. Plasma sodium and glucose concentrations remained stable in treated AMD, pulsed, fluidized beds of limestone and carbon-dioxide pre-treatment of influent, and in AMD-free water. Results indicate that effluents produced by this treatment system were not toxic to these fish, despite still containing moderate concentrations of manganese (3-4 mg l{sup 1} following dilution in exposure systems), and provide justification for field deployment and further biological testing of this treatment in the field.

  13. Chiritopsis longzhouensis, a New Species of Gesneriaceae from Limestone Areas in Guangxi, China

    Directory of Open Access Journals (Sweden)

    Bo Pan

    2010-11-01

    Full Text Available A new species of Gesneriaceae, Chiritopsis longzhouensis B. Pan & W. H. Wu from limestone areas in Guangxi, China, is described and illustrated. The new species is similar to C. jingxiensis Yan Liu, W. B. Xu & H. S. Gao in the corolla shape, but differs in its leaf blade 2-4 × 1.3-2.5 cm, appressed pilose on both surfaces, Cymes 5-10, 1-3-branched, each 5-25-flowered, filaments geniculate about 1 mm above base, sparsely glandular-puberulent, staminodes 3.

  14. Synthesis of Calcite Nano Particles from Natural Limestone assisted with Ultrasonic Technique

    Science.gov (United States)

    Handayani, M.; Sulistiyono, E.; Firdiyono, F.; Fajariani, E. N.

    2018-03-01

    This article represents a precipitation method assisted with ultrasonic process to synthesize precipitated calcium carbonate nano particles from natural limestone. The synthesis of nanoparticles material of precipitated calcium carbonate from commercial calcium carbonate was done for comparison. The process was performed using ultrasonic waves at optimum condition, that is, at temperature of 80oC for 10 minutes with various amplitudes. Synthesized precipitated calcium carbonate nanoparticles were characterized using X-Ray Diffraction (XRD), Scanning Electron Microscope (SEM) and Particle Size Analyzer (PSA). The result of PSA measurements showed that precipitated calcium carbonate nano particles was obtained with the average size of 109 nm.

  15. Mill tailings based composites as paste backfill in mines of U-bearing dolomitic limestone ore

    Directory of Open Access Journals (Sweden)

    Sandeep Panchal

    2018-04-01

    Full Text Available This paper elaborates on the development of paste backfill using mill tailings generated during the processing of a uranium ore deposit hosted in dolomitic limestone. The tailings have been characterized in terms of the physical, chemical and mineralogical properties. Time-dependent rheological behaviors and geotechnical properties of cemented paste backfill (CPB are also determined. The studies show that the mill tailing has the potential to form paste and the CPB has adequate strength to provide support to mine pillars, roofs, and walls. Keywords: Mining engineering, Uranium ore deposit, Tailings, Cemented paste backfill (CPB, Rheology, Compressive strength

  16. Fine root dynamics in lodgepole pine and white spruce stands along productivity gradients in reclaimed oil sands sites.

    Science.gov (United States)

    Jamro, Ghulam Murtaza; Chang, Scott X; Naeth, M Anne; Duan, Min; House, Jason

    2015-10-01

    Open-pit mining activities in the oil sands region of Alberta, Canada, create disturbed lands that, by law, must be reclaimed to a land capability equivalent to that existed before the disturbance. Re-establishment of forest cover will be affected by the production and turnover rate of fine roots. However, the relationship between fine root dynamics and tree growth has not been studied in reclaimed oil sands sites. Fine root properties (root length density, mean surface area, total root biomass, and rates of root production, turnover, and decomposition) were assessed from May to October 2011 and 2012 using sequential coring and ingrowth core methods in lodgepole pine (Pinus contorta Dougl.) and white spruce (Picea glauca (Moench.) Voss) stands. The pine and spruce stands were planted on peat mineral soil mix placed over tailings sand and overburden substrates, respectively, in reclaimed oil sands sites in Alberta. We selected stands that form a productivity gradient (low, medium, and high productivities) of each tree species based on differences in tree height and diameter at breast height (DBH) increments. In lodgepole pine stands, fine root length density and fine root production, and turnover rates were in the order of high > medium > low productivity sites and were positively correlated with tree height and DBH and negatively correlated with soil salinity (P < 0.05). In white spruce stands, fine root surface area was the only parameter that increased along the productivity gradient and was negatively correlated with soil compaction. In conclusion, fine root dynamics along the stand productivity gradients were closely linked to stand productivity and were affected by limiting soil properties related to the specific substrate used for reconstructing the reclaimed soil. Understanding the impact of soil properties on fine root dynamics and overall stand productivity will help improve land reclamation outcomes.

  17. Minimization of gully erosion on reclaimed surface mines using the stable slope and sediment transport computer model

    International Nuclear Information System (INIS)

    McKenney, R.A.; Gardner, T.G.

    1992-01-01

    Disequilibrium between slope form and hydrologic and erosion processes on reclaimed surface coal mines in the humid temperate northeastern US, can result in gully erosion and sediment loads which are elevated above natural, background values. Initial sheetwash erosion is surpassed by gully erosion on reclamation sites which are not in equilibrium with post-mining hydrology. Long-term stability can be attained by designing a channel profile which is in equilibrium with the increased peak discharges found on reclaimed surface mines. The Stable Slope and Sediment transport model (SSAST) was developed to design stable longitudinal channel profiles for post-mining hydrologic and erosional processes. SSAST is an event based computer model that calculates the stable slope for a channel segment based on the post-mine hydrology and median grain size of a reclaimed surface mine. Peak discharge, which drives post-mine erosion, is calculated from a 10-year, 24-hour storm using the Soil Conservation Service curve number method. Curve number calibrated for Pennsylvania surface mines are used. Reclamation sites are represented by the rectangle of triangle which most closely fits the shape of the site while having the same drainage area and length. Sediment transport and slope stability are calculated using a modified Bagnold's equation with a correction factor for the irregular particle shapes formed during the mining process. Data from three reclaimed Pennsylvania surface mines were used to calibrate and verify SSAST. Analysis indicates that SSAST can predict longitudinal channel profiles for stable reclamation of surface mines in the humid, temperate northeastern US

  18. Fault-related dolomitization in the Vajont Limestone (Southern Alps, Italy): photogrammetric 3D outcrop reconstruction, visualization with textured surfaces, and structural analysis

    OpenAIRE

    Bistacchi, Andrea; Balsamo, Fabrizio; Storti, Fabrizio; Mozafari, Mahtab; Swennen, Rudy; Solum, John; Taberner, Conxita

    2013-01-01

    The Vajont Gorge (Dolomiti Bellunesi, Italy) provides spectacular outcrops of Jurassic limestones (Vajont Limestone Formation) in which Mesozoic and Alpine faults and fracture corridors are continuously exposed. Some of these faults acted as conduits for fluids, resulting in structurally-controlled dolomitization of the Vajont Limestone, associated with significant porosity increase. We carried out a 3D surface characterization of the outcrops, combining high resolution topography and imaging...

  19. Testing the assumptions behind emissions trading in non-market goods: the RECLAIM program in Southern California

    International Nuclear Information System (INIS)

    Lejano, Raul P.; Hirose, Rei

    2005-01-01

    Emissions trading is, essentially, a policy instrument that is designed to simulate a market for an otherwise public good. Conceptually, its justification hinges on a number of key assumptions, namely the negligibility of local impacts, the ability to separate and commodify the good in question, and characteristics of a well-functioning market. The authors examine the performance of RECLAIM, a NO x emissions trading program in Southern California, USA, and illustrate how to test these assumptions. There is some evidence that the trading of NO x generates new externalities, such as the possibility that other air pollutants, e.g. volatile organics, are essentially traded along with it. Moreover, the RECLAIM program has recently begun to experience difficulties due to the fact that the market is relatively thin. This analysis provides ways to assess more deeply and reform these trading regimes, including opening up RECLAIM to public review. The case study speaks to a wider arena, as emissions trading is presently being considered in other parts of the world to address issues ranging from acid rain to non-point source pollution to greenhouse gases. The analytic approach, illustrated herein, is a general one that has a wider applicability than the particular case of NO x trading. It is hoped that this kind of critical inquiry can lead to a more careful deliberation of the merits and challenges of emissions trading

  20. Identification and characterization of near surface cavities in Tuwaiq Mountain Limestone, Riyadh, KSA, “detection and treatment”

    Directory of Open Access Journals (Sweden)

    Ahmed Abd El Aal

    2017-03-01

    Full Text Available This study evaluates the capability of surface electrical resistivity technique for identifying the weak zones or subsurface cavities in karst area with limestone rocks. Weak zones or cavities near surface can be potentially dangerous and several problems are associated with collapse of roads or buildings accompanied by subsidence phenomena. Karst environments are characterized by distinctive landforms, which are related to dissolution and dominant subsurface drainage. The interaction of limestone with water is able to create karst features such as cavity, pinnacle, boulder and sinkhole through the dissolution process. The existence of subsurface karst features are always a matter of concern to engineers before any development starts because these features could cause disaster in the future. The study was conducted at Tuwaiq Mountain Limestone, Riyadh region, KSA with the objective to detect and treat karst features at limestone rocks. The karst features such as fill cavity, boulder, pinnacle, discontinuity and overhang were detected in the survey lines. The 2-D ER results showed a good correlation with all the borehole records in determining the subsurface of limestone formation. The 2-D ER method is capable in mapping karst features and bedrock depth. The ability of the electrical technique to produce high resolution images of the subsurface, which are useful for subsidence assessment is illustrated.