Blast resistant vehicle seat

Science.gov (United States)

Ripley, Edward B

2013-02-12

Disclosed are various seats for vehicles particularly military vehicles that are susceptible to attack by road-bed explosive devices such as land mines or improvised explosive devices. The seats often have rigid seat shells and may include rigid bracing for rigidly securing the seat to the chassis of the vehicle. Typically embodiments include channels and particulate media such as sand disposed in the channels. A gas distribution system is generally employed to pump a gas through the channels and in some embodiments the gas is provided at a pressure sufficient to fluidize the particulate media when an occupant is sitting on the seat.

Risk of injury for occupants of motor vehicle collisions from unbelted occupants.

Science.gov (United States)

MacLennan, P A; McGwin, G; Metzger, J; Moran, S G; Rue, L W

2004-12-01

Unbelted occupants may increase the risk of injury for other occupants in a motor vehicle collision (MVC). This study evaluated the association between occupant restraint use and the risk of injury (including death) to other vehicle occupants. A population based cohort study. United States. MVC occupants (n = 152 191 unweighted, n = 18 426 684 weighted) seated between a belted or unbelted occupant and the line of the principal direction of force in frontal, lateral, and rear MVCs were sampled from the 1991-2002 National Automotive Sampling System General Estimates System. Offset MVCs were not included in the study. Risk ratios and 95% confidence intervals for injury (including death) for occupants seated contiguous to unbelted occupants compared to occupants seated contiguous to belted occupants. Risk ratios were adjusted for at risk occupant's sex, age, seating position, vehicle type, collision type, travel speed, crash severity, and at risk occupants' own seat belt use. Exposure to unbelted occupants was associated with a 40% increased risk of any injury. Belted at risk occupants were at a 90% increased risk of injury but unbelted occupants were not at increased risk. Risks were similar for non-incapacitating and capacitating injuries. There was a 4.8-fold increased risk of death for exposed belted occupants but no increased risk of death for unbelted occupants. Belted occupants are at an increased risk of injury and death in the event of a MVC from unbelted occupants.

76 FR 11418 - Rear Visibility; Federal Motor Vehicle Safety Standard, Rearview Mirrors; Federal Motor Vehicle...

Science.gov (United States)

2011-03-02

... rulemaking (NPRM) to expand the required field of view for all passenger cars, trucks, multipurpose passenger... rear-mounted video camera and an in- vehicle visual display. Adoption of this proposal would...

Occupant Kinematics in Simulated Autonomous Driving Vehicle Collisions: Influence of Seating Position, Direction and Angle.

Science.gov (United States)

Kitagawa, Yuichi; Hayashi, Shigeki; Yamada, Katsunori; Gotoh, Mitsuaki

2017-11-01

This two-part study analyzed occupant kinematics in simulated collisions of future automated driving vehicles in terms of seating configuration. In part one, a frontal collision was simulated with four occupants with the front seats reversed. The left front seat occupant was unbelted while the others were belted. In part two of the study, occupant restraint was examined in various seating configurations using a single seat model with a three-point seatbelt. The seat direction with respect to impact was considered as forward, rearward, and lateral facing in 45 degree increments. The effect of seat recline was also studied in the forward-facing and rear-facing cases by assuming three positions: driving position, resting position and relaxed position. Occupants were represented by human body finite element models. The results of part one showed that the front seat (rear-facing) occupants were restrained by the seatback, resulting in T1 forward displacement less than 100 mm; the rear seat occupants were restrained by the seatbelt resulting larger T1 forward displacement more than 500 mm. The results of the part two showed the directional dependence of occupant restraint. Greater T1 displacements were observed when the occupant faced lateral or front oblique. However, the seatbelt provided some restraint in all directions considered. The seatback generated contact force to the occupant when it was in the impact direction, including the lateral directions. The relaxed position allowed increased excursion compared to the driving position when the occupant faced rearward, but the magnitude of this increase was lower with lower impact speed.

75 FR 67233 - Federal Motor Vehicle Safety Standards; Head Restraints

Science.gov (United States)

2010-11-02

... passenger vehicles, and vans). Of these whiplash injuries, 272,464 occurred as a result of rear impacts. For... approximately 18.5 inches with respect to the seat pan * * *. It appeared that an occupant whose sitting...

[The use of seatbelts and child seats in drivers and passengers of motor vehicles in four metropolitan areas in Mexico].

Science.gov (United States)

Cervantes-Trejo, Arturo; Leenen, Iwin

2015-01-01

To estimate the rate of seatbelt and child seat use in drivers and passengers of motor vehicles in four metropolitan areas in Mexico (Guadalajara, León, Monterrey and Mexico City). To evaluate the impact of the Mexican Initiative for Road Safety (IMESEVI) in this respect. Data were collected at the start of IMESEVI (June 2008) and one year after the program's implementation (October 2009) in the four participating metropolitan areas. In particular, the use of seatbelts and child seats was observed in occupants of automobiles, station wagons, and light trucks. The sample included 28,412 (pre) and 52,274 (post) individuals, of which 1,454 (pre) and 1,679 (post) were younger than five years old. The data analysis was based on a hierarchical logistic model. Globally, the probability of using either safety device is 46% (95% CI: 43-49%) at baseline and 52% (95% CI: 48-55%) at the post measurement, with large differences, though, among the four participating metropolitan areas. Factors that significantly affect their use include the individual's position in the vehicle, the type and age of the vehicle, and the individual's sex. Child seat use is very limited. At baseline, about 17% (95% CI: 11-25%) of children below five years old travelled in a special seat, with this number increasing to 26% (95% CI: 19-34%) after the implementation of IMESEVI. Child seat use for children above four years is virtually nonexistent. Continued efforts are required to raise the public awareness of the importance of using safety devices, especially for passengers in the back of the car as well as with respect to the use of adapted seats for small children.

49 CFR 398.4 - Driving of motor vehicles.

Science.gov (United States)

2010-10-01

.... Lighting devices and reflectors. Tires. Horn. Windshield wiper or wipers. Rear-vision mirror or mirrors.... No driver or any employee of a motor carrier shall: (1) Fuel a motor vehicle with the engine running, except when it is necessary to run the engine to fuel the vehicle; (2) Smoke or expose any open flame in...

Emergency department transport rates of children from the scene of motor vehicle collisions: do booster seats make a difference?

Science.gov (United States)

House, Darlene R; Huffman, Gretchen; Walthall, Jennifer D H

2012-11-01

Motor vehicle collisions (MVCs) are the leading cause of death and disability among children older than 1 year. Many states currently mandate all children between the ages of 4 and 8 years be restrained in booster seats. The implementation of a booster-seat law is generally thought to decrease the occurrence of injury to children. We hypothesized that appropriate restraint with booster seats would also cause a decrease in emergency department (ED) visits compared with children who were unrestrained. This is an important measure as ED visits are a surrogate marker for injury. The main purpose of this study was to look at the rate of ED visits between children in booster seats compared with those in other or no restraint systems involved in MVCs. Injury severity was compared across restraint types as a secondary outcome of booster-seat use after the implementation of a state law. A prospective observational study was performed including all children 4 to 8 years old involved in MVCs to which emergency medical services was dispatched. Ambulance services used a novel on-scene computer charting system for all MVC-related encounters to collect age, sex, child-restraint system, Glasgow Coma Scale score, injuries, and final disposition. One hundred fifty-nine children were studied with 58 children (35.6%) in booster seats, 73 children in seatbelts alone (45.2%), and 28 children (19.1%) in no restraint system. 76 children (47.7%), 74 by emergency medical services and 2 by private vehicle, were transported to the ED with no significant difference between restraint use (P = 0.534). Utilization of a restraint system did not significantly impact MVC injury severity. However, of those children who either died (n = 2) or had an on-scene decreased Glasgow Coma Scale score (n = 6), 75% (6/8) were not restrained in a booster seat. The use of booster-seat restraints does not appear to be associated with whether a child will be transported to the ED for trauma evaluation.

Rural and Urban Differences in Passenger-Vehicle-Occupant Deaths and Seat Belt Use Among Adults - United States, 2014.

Science.gov (United States)

Beck, Laurie F; Downs, Jonathan; Stevens, Mark R; Sauber-Schatz, Erin K

2017-09-22

Motor-vehicle crashes are a leading cause of death in the United States. Compared with urban residents, rural residents are at an increased risk for death from crashes and are less likely to wear seat belts. These differences have not been well described by levels of rurality. 2014. Data from the Fatality Analysis Reporting System (FARS) and the Behavioral Risk Factor Surveillance System (BRFSS) were used to identify passenger-vehicle-occupant deaths from motor-vehicle crashes and estimate the prevalence of seat belt use. FARS, a census of U.S. motor-vehicle crashes involving one or more deaths, was used to identify passenger-vehicle-occupant deaths among adults aged ≥18 years. Passenger-vehicle occupants were defined as persons driving or riding in passenger cars, light trucks, vans, or sport utility vehicles. Death rates per 100,000 population, age-adjusted to the 2000 U.S. standard population and the proportion of occupants who were unrestrained at the time of the fatal crash, were calculated. BRFSS, an annual, state-based, random-digit-dialed telephone survey of the noninstitutionalized U.S. civilian population aged ≥18 years, was used to estimate prevalence of seat belt use. FARS and BRFSS data were analyzed by a six-level rural-urban designation, based on the U.S. Department of Agriculture 2013 rural-urban continuum codes, and stratified by census region and type of state seat belt enforcement law (primary or secondary). Within each census region, age-adjusted passenger-vehicle-occupant death rates per 100,000 population increased with increasing rurality, from the most urban to the most rural counties: South, 6.8 to 29.2; Midwest, 5.3 to 25.8; West, 3.9 to 40.0; and Northeast, 3.5 to 10.8. (For the Northeast, data for the most rural counties were not reported because of suppression criteria; comparison is for the most urban to the second-most rural counties.) Similarly, the proportion of occupants who were unrestrained at the time of the fatal crash

Car seat inspection among children older than 3 years: Using data to drive practice in child passenger safety.

Science.gov (United States)

Kroeker, Amber M; Teddy, Amy J; Macy, Michelle L

2015-09-01

Motor vehicle crashes are the leading cause of unintentional death and disability among children 4 years to 12 years of age in the United States. Despite the high risk of injury from motor vehicle crashes in this age group, parental awareness and child passenger safety programs in particular may lack focus on this age group. This is a retrospective cross-sectional analysis of child passenger safety seat checklist forms from two Safe Kids coalitions in Michigan (2013) to identify restraint type upon arrival to car seat inspections. Other variables were included if the coalition provided a new child safety seat and if the child had a sibling who underwent a car seat inspection. χ statistics were used to compare change in restraint use on arrival and at departure, the proportion of children attending a car seat inspection event by age, the age category of children by site, the proportion of children with siblings also undergoing a car seat inspection by age, and the distribution of a new child safety seat by age. Data were available from 1,316 Safe Kids Huron Valley and 3,215 Safe Kids Greater Grand Rapids car seat inspections. Just 10.8% of the total seats inspected were booster seats. Child safety seats for infant and young children were more commonly inspected (rear-facing carrier [40.3%], rear-facing convertible [10.2%], and forward-facing [19.3%] car seats). Few children at inspections used a seat belt only (5.4%) or had no restraint (13.8%). Children 4 years and older were found to be in a suboptimal restraint at least 30% of the time. Low proportions of parents use car seat inspections for children in the booster seat age group. The proportion of children departing the inspection in a more protective restraint increased with increasing age. This highlights an area of weakness in child passenger safety programs and signals an opportunity to strengthen efforts on The Booster Age Child. Epidemiologic/prognostic study, level III.

75 FR 68663 - Federal Motor Vehicle Safety Standards; Rear Impact Guards; Rear Impact Protection; Technical...

Science.gov (United States)

2010-11-08

... nationwide downward trend in fatalities when a passenger vehicle rear-ends a tractor- trailer--neither in... total crashes. The Fatality Accident Reporting System does not list the model year of the trailer. In... submitted on behalf of an association, business, labor union, etc.). You may review DOT's complete Privacy...

49 CFR 392.16 - Use of seat belts.

Science.gov (United States)

2010-10-01

... Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR CARRIER SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR CARRIER SAFETY REGULATIONS DRIVING OF COMMERCIAL MOTOR VEHICLES Driving of Commercial Motor Vehicles § 392.16 Use of seat belts. A commercial motor vehicle which...

Does obesity affect the position of seat belt loading in occupants involved in real-world motor vehicle collisions?

Science.gov (United States)

Hartka, Thomas R; Carr, Hannah M; Smith, Brittany R; Melmer, Monica; Sochor, Mark R

2018-02-28

Previous work has shown that the lap belt moves superior and forward compared to the bony pelvis as body mass index (BMI) increases. The goal of this project was to determine whether the location of lap belt loading is related to BMI for occupants who sustained real-world motor vehicle collisions (MVCs). A national MVC database was queried for vehicle occupants over a 10-year period (2003-2012) who were at least 16 years old, restrained by a 3-point seat belt, sitting in the front row, and involved in a front-end collision with a change in velocity of at least 56 km/h. Cases were excluded if there was not an available computed tomography (CT) scan of the abdomen. CT scans were then analyzed using adipose enhancement of 3-dimensional reconstructions. Scans were assessed for the presence a radiographic seat belt sign (rSBS), or subcutaneous fat stranding due to seat belt loading. In scans in which the rSBS was present, anterior and superior displacement of rSBS from the anterior-superior iliac spine (ASIS) was measured bilaterally. This displacement was correlated with BMI and injury severity. The inclusion and exclusion criteria yielded 151 cases for analysis. An rSBS could definitively be identified in 55 cases. Cases in which occupants were older and had higher BMI were more likely to display an rSBS. There was a correlation between increasing BMI and anterior rSBS displacement (P obesity may worsen horizontal position but not the vertical position of the lap belt loading during real-world frontal MVCs.

Thoracic aortic injury in motor vehicle crashes: the effect of impact direction, side of body struck, and seat belt use.

Science.gov (United States)

Fitzharris, Michael; Franklyn, Melanie; Frampton, Richard; Yang, King; Morris, Andrew; Fildes, Brian

2004-09-01

Using in-depth, real-world motor vehicle crash data from the United States and the United Kingdom, we aimed to assess the incidence and risk factors associated with thoracic aorta injuries. De-identified National Automotive Sampling System Crashworthiness Data System (U.S.) and Co-operative Crash Injury Study (U.K.) data formed the basis of this retrospective analysis. Logistic regression was used to assess the level of risk of thoracic aorta injury associated with impact direction, seat belt use and, given the asymmetry of the thoracic cavity, whether being struck toward the left side of the body was associated with increased risk in side-impact crashes. A total of 13,436 U.S. and 3,756 U.K. drivers and front seat passengers were analyzed. The incidence of thoracic aorta injury in the U.S. and U.K. samples was 1.5% (n = 197) and 1.9% (n = 70), respectively. The risk was higher for occupants seated on the side closest to the impact than for occupants involved in frontal impact crashes. This was the case irrespective of whether the force was applied toward the left (belted: relative risk [RR], 4.6; 95% confidence interval [CI], 2.9-7.1; p direction. Thoracic aorta injuries were found to be associated with high impact severity, and being struck by a sports utility vehicle relative to a passenger vehicle (RR, 1.7; 95% CI, 1.2-2.3; p = 0.001). Aortic injuries have been conventionally associated with frontal impacts. However, emergency clinicians should be aware that occupants of side-impact crashes are at greater risk, particularly if the occupant was unbelted and involved in a crash of high impact severity.

Protection of children restrained in child safety seats in side impact crashes.

Science.gov (United States)

Arbogast, Kristy B; Locey, Caitlin M; Zonfrillo, Mark R; Maltese, Matthew R

2010-10-01

The performance of child restraint systems (CRS) in side impact motor vehicle crashes has been under study due to the injury and fatality burden of these events. Although previous research has quantified injury risk or described injured body regions, safety advances require an understanding of injury causation. Therefore, the objective was to delineate injury causation scenarios for CRS-restrained children in side impacts and document probable contact points in the vehicle interior. Two in-depth crash investigation databases, the Crash Injury Research and Engineering Network and the Partners for Child Passenger Safety Study, were queried for rear-seated, CRS-restrained children in side impact crashes who sustained Abbreviated Injury Scale 2+ injury. These cases were reviewed by a multidisciplinary team of physicians and engineers to describe injury patterns, injury causation, and vehicle components that contributed to the injuries. Forty-one occupants (average age, 2.6 years) met the inclusion criteria. Twenty-four were near side to the crash, 7 were far side, and 10 were center seated. The most common injuries were to the skull and brain with an increasing proportion of skull fracture as age increased. Head and spine injuries without evidence of head contact were rare but present. All thoracic injuries were lung contusions and no rib fractures occurred. Near-side head and face contacts points were along the rear vertical plane of the window and the horizontal plane of the window sill. Head and face contact points for center- and far-side occupants were along the edges of the front seat back and front seat head restraint. Head injuries are the target for injury prevention for children in CRS in side impact crashes. Most of these injuries are due to the contact; for near-side occupants, contact with the CRS structure and the door interior, for far- or center-seated occupants, contact with the front seat back. These data are useful in developing both educational and

Stability of the Small Electric Vehicle with Two In-Wheel Motors

Directory of Open Access Journals (Sweden)

Heerwan P.M.

2017-01-01

Full Text Available For a small electric vehicle (EV with the rear two in-wheel motors, the hydraulic brake system and the mechanical brake system are installed at the front and rear tire respectively. The mechanical brake system is used at the rear tire because there is no enough space for the hydraulic brake system. In a braking condition, the in-wheel motor at the rear tire will generate the regenerative braking force and it can improve the braking performance of the vehicle. However, during braking on the low adhesion road surface, anti-lock brake system (ABS is very crucial to prevent the tire from lock-up. To improve the safety and stability of the vehicle, the combination of anti-skid control system and direct yaw moment control system is proposed. The anti-skid control system contains a hydraulic unit of ABS at the front tires and regenerative brake timing control at the rear tires. The control method of the regenerative brake timing control is same as ABS and it will turn on and off to prevent the tire from lock-up. On the other hand, the direct yaw moment control system is developed to increase the steer performance of the vehicle. The optimal control is used as the control strategy method to control the yaw moment. The simulation is developed in MATLAB Simulink and the result shows that the proposed model can improve the stopping distance from 9 seconds to 8.2 seconds. In addition, the combination of skid control and yaw moment control also improved the steer performance of the vehicle.

Evaluation of Severity Score in Patients with Lower Limb and Pelvic Fractures Injured in Motor Vehicle Front-Impact Collisions.

Science.gov (United States)

Gokalp, Mehmet Ata; Hekimoglu, Yavuz; Gozen, Abdurrahim; Guner, Savas; Asirdizer, Mahmut

2016-12-01

BACKGROUND Lower limb and pelvic injuries and fractures occur at a very high incidence in motor vehicle accidents. In this study, the characteristics (e.g., body side, bone location, and fracture severity) of lower limb and pelvic fractures that occurred during front-impact collisions were correlated with the injured patients' sex, age, and position in the vehicle. MATERIAL AND METHODS We retrospectively evaluated 191 patients (136 males, 55 females) who were injured in motor vehicle accidents, specifically in frontal collisions. RESULTS This study revealed that most of lower limb and pelvic fractures occurred in males (71.2%; p=.000), 19-36 years old (55.5%; p=.000), small vehicles (86.4%; p=.000), and rear seat passengers (49.2%; p=.000). Fractures most commonly occurred in the left side of the body (46.6%; p=.000) and upper legs (37.7%; p=.000). Severity scores were higher (2.76) in males than females (2.07). No statistically significant was found in severity scores of patients and other personal characteristics and fracture features of patients with lower limb and pelvic fractures who were injured in a vehicle during front-impact collisions (p>0.05). CONCLUSIONS The results of this study will be useful for the automobile industry, forensics and criminal scientists, and for trauma research studies.

Kineto-dynamic design optimisation for vehicle-specific seat-suspension systems

Science.gov (United States)

Shangguan, Wen-Bin; Shui, Yijie; Rakheja, Subhash

2017-11-01

Designs and analyses of seat-suspension systems are invariably performed considering effective vertical spring rate and damping properties, while neglecting important contributions due to kinematics of the widely used cross-linkage mechanism. In this study, a kineto-dynamic model of a seat-suspension is formulated to obtain relations for effective vertical suspension stiffness and damping characteristics as functions of those of the air spring and the hydraulic damper, respectively. The proposed relations are verified through simulations of the multi-body dynamic model of the cross-linkage seat-suspension in the ADAMS platform. The validity of the kineto-dynamic model is also demonstrated through comparisons of its vibration transmission response with the experimental data. The model is used to identify optimal air spring coordinates to attain nearly constant natural frequency of the suspension, irrespective of the seated body mass and seated height. A methodology is further proposed to identify optimal damping requirements for vehicle-specific suspension designs to achieve minimal seat effective amplitude transmissibility (SEAT) and vibration dose value (VDV) considering vibration spectra of different classes of earthmoving vehicles. The shock and vibration isolation performance potentials of the optimal designs are evaluated under selected vehicle vibration superimposed with shock motions. Results show that the vehicle-specific optimal designs could provide substantial reductions in the SEAT and VDV values for the vehicle classes considered.

Vibration Analysis of 5-DOF Vehicle Model under Stochastic Road Surface Excitation

Directory of Open Access Journals (Sweden)

Zhang Yanlong

2016-01-01

Full Text Available Considering human body vertical motion, vehicle body vertical motion, pitch movement and vertical jump of front and rear wheels, a five-degree-of-freedom vehicle model is established to study basic driving characteristics of the vehicle. Using Fourier transform method, acceleration power spectral density of the seat and the mean square value curves of seat vertical weighted acceleration are obtained by numerical simulation. Combined with comfort provision standards, the influence of vehicle model parameters and speed on seat acceleration power spectral density and vertical root-mean-square value of seat weighted acceleration are analyzed. Results show that the stiffness and damping of the seat have no significant effect on seat acceleration power spectral density, and seat acceleration PSD increases with increasing front or rear suspension stiffness, but it decreases with increasing front or rear suspension damping. It should also be concluded that the model stiffness and the mean square value of seat vertical weighted acceleration present positive correlation in general, but seat vertical weighted acceleration decrease first and then increase when model damping increase. Such analysis results can provide reference for the parameter optimization design of the automobile.

Evaluation of ISO CRS Envelopes Relative to U.S. Vehicles and Child Restraint Systems.

Science.gov (United States)

Hu, Jingwen; Manary, Miriam A; Klinich, Kathleen D; Reed, Matthew P

2015-01-01

The objectives of this study are to use computer simulation to evaluate the International Organization for Standardization (ISO) 13216-3:2006(E) child restraint system (CRS) envelopes relative to rear seat compartments from vehicles and CRSs in the U.S. market, investigate the potential compatibility issues of U.S. vehicles and CRSs, and demonstrate whether necessary modifications can be made to introduce such a system into compatibility evaluations between U.S. vehicles and CRSs. Three-dimensional geometry models for 26 vehicles and 16 convertible CRS designs developed previously were used. Geometry models of 3 forward-facing and 3 rear-facing CRS envelopes provided by the ISO were built in the current study. The virtual fit process closely followed the physical procedures described in the ISO standards. The results showed that the current ISO rear-facing envelopes can provide reasonable classifications for CRSs and vehicles, but the forward-facing envelopes do not represent products currently in the U.S. market. In particular, all of the selected vehicles could accommodate the largest forward-facing CRS envelope at the second-row seat location behind the driver seat. In contrast, half of the selected CRSs could not fit within any of the forward-facing ISO CRS envelopes, mainly due to protrusion at the rear-top corner of the envelope. The results also indicate that the rear seat compartment in U.S. vehicles often cannot accommodate a large portion of convertible CRSs in the rear-facing position. The increased demand for vehicle fuel economy and the recommendation to keep children rear-facing longer may lead to smaller cars and larger CRSs, which may increase the potential for fit problems. The virtual classifications indicated that contact between the forward-facing CRSs and the head restraints in the rear seats as well as that between the rear-facing CRSs and the back of the front seats is a main concern regarding the compatibility between the vehicles and the

NASA Standards Inform Comfortable Car Seats

Science.gov (United States)

2014-01-01

NASA developed standards, which included the neutral body posture (NBP), to specify ways to design flight systems that support human health and safety. Nissan Motor Company, with US offices in Franklin, Tennessee, turned to NASA's NBP research for the development of a new driver's seat. The 2013 Altima now features the new seat, and the company plans to incorporate the seats in upcoming vehicles.

Adaptive magnetorheological seat suspension for the expeditionary fighting vehicle

International Nuclear Information System (INIS)

Hiemenz, G J; Hu, W; Wereley, N M

2009-01-01

The Expeditionary Fighting Vehicle (EFV) is an amphibious vehicle designed to operate through harsh conditions and at much higher speeds than its predecessors. These unique capabilities and broadly varying operational conditions lead to a complex design and human factors scenario for the forward seating positions that cannot be solved using conventional passive seat suspension systems. Injurious shock loads transmitted to the occupants when traversing over water in high sea states and/or at high speeds, as well as harmful shock and vibration transmitted to the occupants when the vehicle is travelling over land, pose a threat to occupant health and significantly limit mission duration. In this study, a semi-active magnetorheological (MR) seat suspension is developed which adapts to broadly varying operational conditions, as well as occupant weight, to provide optimal protection of EFV occupants. It is shown that this MR seat suspension system will reduce the shock and vibration transmitted to the occupant by up to 33% and 65%, respectively, as compared to the existing passive suspension.

Adaptive magnetorheological seat suspension for the expeditionary fighting vehicle

Energy Technology Data Exchange (ETDEWEB)

Hiemenz, G J [Techno-Sciences, Inc., 11750 Beltsville Dr. Ste. 300, Beltsville, MD 20705 (United States); Hu, W; Wereley, N M [Aerospace Engineering, University of Maryland, College Park, MD 20712 (United States)], E-mail: greg@technosci.com, E-mail: wereley@umd.edu

2009-02-01

The Expeditionary Fighting Vehicle (EFV) is an amphibious vehicle designed to operate through harsh conditions and at much higher speeds than its predecessors. These unique capabilities and broadly varying operational conditions lead to a complex design and human factors scenario for the forward seating positions that cannot be solved using conventional passive seat suspension systems. Injurious shock loads transmitted to the occupants when traversing over water in high sea states and/or at high speeds, as well as harmful shock and vibration transmitted to the occupants when the vehicle is travelling over land, pose a threat to occupant health and significantly limit mission duration. In this study, a semi-active magnetorheological (MR) seat suspension is developed which adapts to broadly varying operational conditions, as well as occupant weight, to provide optimal protection of EFV occupants. It is shown that this MR seat suspension system will reduce the shock and vibration transmitted to the occupant by up to 33% and 65%, respectively, as compared to the existing passive suspension.

41 CFR 102-34.85 - What motor vehicles require motor vehicle identification?

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false What motor vehicles require motor vehicle identification? 102-34.85 Section 102-34.85 Public Contracts and Property Management... 34-MOTOR VEHICLE MANAGEMENT Identifying and Registering Motor Vehicles Motor Vehicle Identification...

Dynamics of a motor vehicle taking into consideration the interaction of wheels and road pavement surface

Directory of Open Access Journals (Sweden)

O. Prentkovskis

2002-12-01

Full Text Available The authors of this article focus on the simulation of the motor vehicle on a certain road and propose their specific solution of this problem. A mathematical model of the system “motor vehicle – road” is presented. The motor vehicle is simulated by concentrated masses interconnected by elastic and dissipative links. The presented model of the motor vehicle evaluates the movement of the motor vehicle body in space; the movement and turning of front and rear suspensions with respect to the body; the interaction of the wheel with the road pavement surface; the blocking of the wheel; the changing cohesive forces which influence the motor vehicle. The investigated road pavement surface is simulated by triangular finite elements, the certain height of road pavement surface roughness and the cohesion coefficients of road pavement surface and the motor vehicle wheel in the longitudinal and transverse directions of the wheel are selected in each finite element nodal point. The presented results illustrate: the motor vehicle movement trajectories braking at various initial conditions and on a certain pavement surface of the road section under investigation and the motor vehicle driving on the speed reduction bump (“sleeping policeman”.

Development and validation of rear impact computer simulation model of an adult manual transit wheelchair with a seated occupant.

Science.gov (United States)

Salipur, Zdravko; Bertocci, Gina

2010-01-01

It has been shown that ANSI WC19 transit wheelchairs that are crashworthy in frontal impact exhibit catastrophic failures in rear impact and may not be able to provide stable seating support and thus occupant protection for the wheelchair occupant. Thus far only limited sled test and computer simulation data have been available to study rear impact wheelchair safety. Computer modeling can be used as an economic and comprehensive tool to gain critical knowledge regarding wheelchair integrity and occupant safety. This study describes the development and validation of a computer model simulating an adult wheelchair-seated occupant subjected to a rear impact event. The model was developed in MADYMO and validated rigorously using the results of three similar sled tests conducted to specifications provided in the draft ISO/TC 173 standard. Outcomes from the model can provide critical wheelchair loading information to wheelchair and tiedown manufacturers, resulting in safer wheelchair designs for rear impact conditions. (c) 2009 IPEM. Published by Elsevier Ltd. All rights reserved.

Children's and Adults' Comfort Experience of Extra Seat Belts When Riding in the Rear Seat of a Passenger Car.

Science.gov (United States)

Osvalder, Anna-Lisa; Hansson, Ida; Bohman, Katarina

2015-01-01

The objective of this study was to explore passengers' comfort experience of extra seat belts during on-road driving in the rear seat of a passenger car and to investigate how the use of extra belts affects children's and adults' attitudes to the product. Two different seat belt systems were tested, criss-cross (CC) and backpack (BP), consisting of the standard 3-point belt together with an additional 2-point belt. In total, 32 participants (15 children aged 6-10, 6 youths aged 11-15, and 11 adults aged 20-79, who differed considerably in size, shape, and proportions) traveled for one hour with each system, including city traffic and highway driving. Four video cameras monitored the test subject during the drive. Subjective data regarding emotions and perceived discomfort were collected in questionnaires every 20 min. A semistructured interview was held afterwards. All participant groups accepted the new products and especially the increased feeling of safety (P car. CC was appreciated for its symmetry, comfort, and the perceived feeling of safety. Some participants found CC unpleasant because the belts tended to slip close to the neck, described as a strangling feeling. BP was simpler to use and did not cause annoyance to the neck in the way CC did. Instead, it felt asymmetric and to some extent less safe than CC. Body size and shape affected seat belt fit to a great extent, which in turn affected the experience of comfort, both initially and over time. Perceived safety benefit and experienced comfort were the most determinant factors for the attitude toward the extra seat belts. The extra seat belts were perceived as being better than the participants had expected before the test, and they became more used to them over time. This exploratory study provided valuable knowledge from a user perspective for further development of new seat belt systems in cars. In addition to an increased feeling of safety, seat belt fit and comfort are supplementary influencing

Average male and female virtual dummy model (BioRID and EvaRID) simulations with two seat concepts in the Euro NCAP low severity rear impact test configuration.

Science.gov (United States)

Linder, Astrid; Holmqvist, Kristian; Svensson, Mats Y

2018-05-01

Soft tissue neck injuries, also referred to as whiplash injuries, which can lead to long term suffering accounts for more than 60% of the cost of all injuries leading to permanent medical impairment for the insurance companies, with respect to injuries sustained in vehicle crashes. These injuries are sustained in all impact directions, however they are most common in rear impacts. Injury statistics have since the mid-1960s consistently shown that females are subject to a higher risk of sustaining this type of injury than males, on average twice the risk of injury. Furthermore, some recently developed anti-whiplash systems have revealed they provide less protection for females than males. The protection of both males and females should be addresses equally when designing and evaluating vehicle safety systems to ensure maximum safety for everyone. This is currently not the case. The norm for crash test dummies representing humans in crash test laboratories is an average male. The female part of the population is not represented in tests performed by consumer information organisations such as NCAP or in regulatory tests due to the absence of a physical dummy representing an average female. Recently, the world first virtual model of an average female crash test dummy was developed. In this study, simulations were run with both this model and an average male dummy model, seated in a simplified model of a vehicle seat. The results of the simulations were compared to earlier published results from simulations run in the same test set-up with a vehicle concepts seat. The three crash pulse severities of the Euro NCAP low severity rear impact test were applied. The motion of the neck, head and upper torso were analysed in addition to the accelerations and the Neck Injury Criterion (NIC). Furthermore, the response of the virtual models was compared to the response of volunteers as well as the average male model, to that of the response of a physical dummy model. Simulations

The effects of seat belt legislation on road traffic injuries.

Science.gov (United States)

Trinca, G W; Dooley, B J

1977-04-01

The compulsory wearing of seat belts, first introduced in the world in Victoria in 1970, has effectively reduced the number of deaths and injuries by approximately one-third for car occupants involved in motor vehicle crashes. Initially, the legislation did not apply to children under the age of eight years, but in 1975 a further law was introduced banning children from the front seat of any vehicle unless properly harnessed. Seat belts offer the best protection for front seat drivers and passengers involved in frontal impacts, but offer less protection to the recipient of a side impact. Ten per cent of car occupants admitted to hospital after a frontal impact show injuries, mostly minor, directly attibutable to the wearing of seat belts.

An image-based method to measure all-terrain vehicle dimensions for engineering safety purposes.

Science.gov (United States)

Jennissen, Charles A; Miller, Nathan S; Tang, Kaiyang; Denning, Gerene M

2014-04-01

All-terrain vehicle (ATV) crashes are a serious public health and safety concern. Engineering approaches that address ATV injury prevention are critically needed. Avenues to pursue include evidence-based seat design that decreases risky behaviours, such as carrying passengers and operation of adult-size vehicles by children. The goal of this study was to create and validate an image-based method to measure ATV seat length and placement. Publicly available ATV images were downloaded. Adobe Photoshop was then used to generate a vertical grid through the centre of the vehicle, to define the grid scale using the manufacturer's reported wheelbase, and to determine seat length and placement relative to the front and rear axles using this scale. Images that yielded a difference greater than 5% between the calculated and the manufacturer's reported ATV lengths were excluded from further analysis. For the 77 images that met inclusion criteria, the mean±SD for the difference in calculated versus reported vehicle length was 1.8%±1.2%. The Pearson correlation coefficient for comparing image-based seat lengths determined by two independent measurers (20 models) and image-based lengths versus lengths measured at dealerships (12 models) were 0.95 and 0.96, respectively. The image-based method provides accurate and reproducible results for determining ATV measurements, including seat length and placement. This method greatly expands the number of ATV models that can be studied, and may be generalisable to other motor vehicle types. These measurements can be used to guide engineering approaches that improve ATV safety design.

Descriptions of Motor Vehicle Collisions by Participants in Emergency Department–Based Studies: Are They Accurate?

Directory of Open Access Journals (Sweden)

Young M. Lee

2012-09-01

Full Text Available Introduction: We examined the accuracy of research participant characterizations of motor vehicle collisions (MVC.Methods: We conducted an emergency department-based prospective study of adults presenting for care after experiencing an MVC. Study participants completed a structured clinical interview that assessed the number of lanes of the road where the collision took place, vehicle type, road condition, speed limit, seat belt use, airbag deployment, vehicle damage, time of collision, and use of ambulance transportation. Study participant data were then compared with information recorded by Michigan State Police at the scene of the MVC. Agreement between research participant reports and police-reported data were assessed by using percentage agreement and j coefficients for categorical variables and correlation coefficients for continuous variables.Results: There were 97 study participants for whom emergency department interviews and Michigan State Police Report information were available. Percentage agreement was 51% for number of lanes,76% for car drivability, 88% for road condition, 91% for vehicle type, 92% for seat belt use, 94% for airbag deployment, 96% for speed limit, 97% for transportation by ambulance, and 99% for vehicle seat position. j values were 0.32 for seat belt use, 0.34 for number of lanes, 0.73 for vehicle type, 0.76 for speed limit, 0.77 for road condition, 0.87 for airbag deployment, 0.90 for vehicle seat position, and 0.94for transport by ambulance. Correlation coefficients were 0.95 for the time of the collision, and 0.58 for extent of damage to the vehicle. Most discrepancies between patients and police about extent of vehicle damage occurred for cases in which the patient reported moderate or severe damage but the police reported only slight damage.Conclusion: For most MVC characteristics, information reported by research participants was consistent with police-reported data. Agreement was moderate or high for

Biomechanical responses of PMHS in moderate-speed rear impacts and development of response targets for evaluating the internal and external biofidelity of ATDS.

Science.gov (United States)

Kang, Yun-Seok; Bolte, John H; Moorhouse, Kevin; Donnelly, Bruce; Herriott, Rodney; Mallory, Ann

2012-10-01

The objectives of this study were to obtain biomechanical responses of post mortem human subjects (PMHS) by subjecting them to two moderate-speed rear impact sled test conditions (8.5g, 17 km/h; 10.5g, 24 km/h) while positioned in an experimental seat system, and to create biomechanical targets for internal and external biofidelity evaluation of rear impact ATDs. The experimental seat was designed to measure external loads on the head restraint (4 load cells), seat back (6 load cells), and seat pan (4 load cells) such that subject dynamic interaction with the seat could be evaluated. This seat system was capable of simulating the dynamic characteristics of modern vehicle seat backs by considering the moment-rotation properties of a typical passenger vehicle, thus providing a more realistic test environment than using a rigid seat with a non-rotating seat back as done in previous studies. Instrumentation used to measure biomechanical responses of the PMHS included both accelerometers and angular rate sensors (ARS). A total of fourteen sled tests using eight PMHS (males 175.8 ± 6.2 cm of stature and 78.4 ± 7.2 kg of weight) provided data sets of seven PMHS for both test conditions. The biomechanical responses are described at both speeds, and cervical spine injuries are documented. Biomechanical targets are also created for internal and external biofidelity evaluation of rear impact anthropomorphic test devices (ATDs).

Feasibility study for the development and marketing of magnesium seats for motor coaches and other modes of public transit

Energy Technology Data Exchange (ETDEWEB)

Bergeron, F. [IC-2 Technologies Inc., Quebec City, PQ (Canada); Audet, J.F. [J-F Audet Courtier Stratege, Carignan, PQ (Canada)

2004-06-01

Magnesium is currently used for seats in many minivans and luxury cars, as well as in some high speed trains. This paper addresses concerns about the use of magnesium in manufacturing seats for public transit vehicles. This paper aimed to validate the feasibility of magnesium and/or aluminum passenger seats and determine if they met weight and cost reduction objectives currently set by the public transportation industry. An assessment of the North American bus and motor coach market was made, and passenger seat design standards were reviewed. Additionally, magnesium samples were tested to ensure industry standards for material flammability and toxic fumes emissions during exposure to intense heat. Corrosion testing and a comparison with automobile industry tests were made. A number of manufacturing case studies were conducted, including life-cycle costs and comparisons with the manufacture of traditional steel seats. It was concluded that a lighter-weight seat is both technically possible and economically viable. In terms of flammability, magnesium seats met all required industry standards, and when combined with excellent seat design, increased the safety of seat occupants projected forward during collisions. In addition, magnesium's ability to absorb vibration was seen as a substantial benefit in terms of passenger comfort. In terms of manufacturing cost alone, a magnesium-aluminum hybrid was recommended. 15 refs., 25 tabs., 24 figs.

Modal Analysis of In-Wheel Motor-Driven Electric Vehicle Based on Bond Graph Theory

Directory of Open Access Journals (Sweden)

Di Tan

2017-01-01

Full Text Available A half-car vibration model of an electric vehicle driven by rear in-wheel motors was developed using bond graph theory and the modular modeling method. Based on the bond graph model, modal analysis was carried out to study the vibration characteristics of the electric vehicle. To verify the effectiveness of the established model, the results were compared to ones computed on the ground of modal analysis and Newton equations. The comparison shows that the vibration model of the electric vehicle based on bond graph theory not only is able to better compute the natural frequency but also can easily determine the deformation mode, momentum mode, and other isomorphism modes and describe the dynamic characteristics of an electric vehicle driven by in-wheel motors more comprehensively than other modal analysis methods.

Assessing rear-end crash potential in urban locations based on vehicle-by-vehicle interactions, geometric characteristics and operational conditions.

Science.gov (United States)

Dimitriou, Loukas; Stylianou, Katerina; Abdel-Aty, Mohamed A

2018-03-01

Rear-end crashes are one of the most frequently occurring crash types, especially in urban networks. An understanding of the contributing factors and their significant association with rear-end crashes is of practical importance and will help in the development of effective countermeasures. The objective of this study is to assess rear-end crash potential at a microscopic level in an urban environment, by investigating vehicle-by-vehicle interactions. To do so, several traffic parameters at the individual vehicle level have been taken into consideration, for capturing car-following characteristics and vehicle interactions, and to investigate their effect on potential rear-end crashes. In this study rear-end crash potential was estimated based on stopping distance between two consecutive vehicles, and four rear-end crash potential cases were developed. The results indicated that 66.4% of the observations were estimated as rear-end crash potentials. It was also shown that rear-end crash potential was presented when traffic flow and speed standard deviation were higher. Also, locational characteristics such as lane of travel and location in the network were found to affect drivers' car following decisions and additionally, it was shown that speeds were lower and headways higher when Heavy Goods Vehicles lead. Finally, a model-based behavioral analysis based on Multinomial Logit regression was conducted to systematically identify the statistically significant variables in explaining rear-end risk potential. The modeling results highlighted the significance of the explanatory variables associated with rear-end crash potential, however it was shown that their effect varied among different model configurations. The outcome of the results can be of significant value for several purposes, such as real-time monitoring of risk potential, allocating enforcement units in urban networks and designing targeted proactive safety policies. Copyright © 2018 Elsevier Ltd. All rights

Biomechanical analysis of protective countermeasures in underride motor vehicle accidents - biomed 2009.

Science.gov (United States)

Kumar, Sri; Enz, Bruce; Ponder, Perry L; Anderson, Bob

2009-01-01

Traffic safety has been significantly improved over the past several decades reducing injury and fatality rates. However, there is a paucity of research effort to address the safety issues in underride accidents, specifically the side underride crashes. It is well known that the compromise of occupant space in the vehicle leads to a higher probability of serious or fatal injuries. A better understanding of occupant protection and mechanism of injuries involved in side underride accidents assists in the advancement of safety measures. The present work evaluates the injury potential to occupants during side underride crashes using the car-to-trailer crash methodology. Four crash tests were conducted into the side of a stationary trailer fitted with the side underride guard system (SURG). The SURG used in these tests is 25% lighter than the previous design. A 5th percentile hybrid III female dummy was placed in the driver seat and restrained with the three-point lap and shoulder harness. The anthropometric dummy was instrumented with a head triaxial accelerometer, a chest triaxal accelerometer, a load cell to measure neck force and moment, and a load cell to measure the femur force. The vehicle acceleration was measured using a traxial accelerometer in the rear center tunnel. High speed, standard video and still photos were taken. In all tests, the intrusion was limited to the front structure of the vehicle without any significant compromise to the occupant space. Results indicate that the resultant head and chest accelerations, head injury criterion (HIC), neck force and moment, and femur force were well below the injury tolerance. The present findings support the hypothesis that the SURG not only limits or eliminates the intrusion into the occupant space but also results in biomechanical injury values well below the tolerance limit in motor vehicle crashes.

An Active Seat Controller with Vehicle Suspension Feedforward and Feedback States: An Experimental Study

Directory of Open Access Journals (Sweden)

Abdulaziz Alfadhli

2018-04-01

Full Text Available Active seat suspensions can be used to reduce the harmful vertical vibration of a vehicle’s seat by applying an external force using a closed loop controller. Many of the controllers found in the literature are difficult to implement practically, because they are based on using unavailable or difficult and costly measurements. This paper presents both simulation and experimental studies of five novel, simple, and cost-effective control strategies to be used for an active seat suspension in order to improve ride comfort at low frequencies below 20 Hz. These strategies use available and measurable feedforward (preview information states from the vehicle secondary suspension, as well as feedback states from the seat suspension, together with gains optimised to minimise the occupant vibration. The gains were optimised using a genetic algorithm (GA, with a fitness function based on the seat effective amplitude transmissibility (SEAT factor. Constraints on the control force and the seat suspension stroke were also included in the optimisation algorithm. Simulation and laboratory experimental tests were carried out to assess the performance of the proposed controllers according to the ISO 2631-1 standard, in both the frequency and time domains with a range of different road profiles. The experimental tests were performed using a multi-axis simulation table (MAST and a physical active seat suspension configured as a hardware-in-loop (HIL simulation with a virtual linear quarter vehicle model (QvM. The results demonstrate that the proposed controllers substantially attenuate the vertical vibration at the driver’s seat compared with both a passive and a proportional-integral-derivative (PID active seat suspension and thus improve ride comfort together with reducing vibration-linked health risks. Moreover, experimental results show that employing both feedforward information and feedback vehicle body and seat acceleration signals in the controller

75 FR 22317 - Federal Motor Vehicle Safety Standards; Small Business Impacts of Motor Vehicle Safety

Science.gov (United States)

2010-04-28

... 1300 [Docket No. NHTSA-2010-0054] Federal Motor Vehicle Safety Standards; Small Business Impacts of Motor Vehicle Safety AGENCY: National Highway Traffic Safety Administration (NHTSA), Department of..., multipurpose passenger vehicles, trucks, buses, trailers, incomplete vehicles, motorcycles, and motor vehicle...

Comparison of car seats in low speed rear-end impacts using the BioRID dummy and the new neck injury criterion (NIC).

Science.gov (United States)

Boström, O; Fredriksson, R; Håland, Y; Jakobsson, L; Krafft, M; Lövsund, P; Muser, M H; Svensson, M Y

2000-03-01

Long-term whiplash associated disorders (WAD) 1-3 sustained in low velocity rear-end impacts is the most common disability injury in Sweden. Therefore, to determine neck injury mechanisms and develop methods to measure neck-injury related parameters are of importance for current crash-safety research. A new neck injury criterion (NIC) has previously been proposed and evaluated by means of dummy, human and mathematical rear-impact simulations. So far, the criterion appears to be sensitive to the major car and collision related risk factors for injuries with long-term consequences. To further evaluate the applicability of NIC, four seats were tested according to a recently proposed sled-test procedure. 'Good' as well as 'bad' seats were chosen on the basis of a recently presented disability risk ranking list. The dummy used in the current tests was the Biofidelic Rear Impact Dummy (BioRID). The results of this study showed that NICmax values were generally related to the real-world risk of long-term WAD 1-3. Furthermore, these results suggested that NICmax calculated from sled tests using the BioRID dummy can be used for evaluating the neck injury risk of different car seats.

Underutilization of occupant restraint systems in motor vehicle injury crashes: A quantitative analysis from Qatar.

Science.gov (United States)

El-Menyar, Ayman; Consunji, Rafael; Asim, Mohammad; Abdelrahman, Husham; Zarour, Ahmad; Parchani, Ashok; Peralta, Ruben; Al-Thani, Hassan

2016-01-01

Restraint systems (seat belts and airbags) are important tools that improve vehicle occupant safety during motor vehicle crashes (MVCs). We aimed to identify the pattern and impact of the utilization of passenger restraint systems on the outcomes of MVC victims in Qatar. A retrospective study was conducted for all admitted patients who sustained MVC-related injuries between March 2011 and March 2014 inclusive. Out of 2,730 road traffic injury cases, 1,830 (67%) sustained MVC-related injuries, of whom 88% were young males, 70% were expatriates, and 53% were drivers. The use of seat belts and airbags was documented in 26 and 2.5% of cases, respectively. Unrestrained passengers had greater injury severity scores, longer hospital stays, and higher rates of pneumonia and mortality compared to restrained passengers (P = .001 for all). There were 311 (17%) ejected cases. Seat belt use was significantly lower and the mortality rate was 3-fold higher in the ejected group compared to the nonejected group (P = .001). The overall mortality was 8.3%. On multivariate regression analysis, predictors of not using a seat belt were being a front seat passenger, driver, or Qatari national and young age. Unrestrained males had a 3-fold increase in mortality in comparison to unrestrained females. The risk of severe injury (relative risk [RR] = 1.82, 95% confidence interval [CI], 1.49-2.26, P = .001) and death (RR = 4.13, 95% CI, 2.31-7.38, P = .001) was significantly greater among unrestrained passengers. The nonuse of seat belts is associated with worse outcomes during MVCs in Qatar. Our study highlights the lower rate of seat belt compliance in young car occupants that results in more severe injuries, longer hospital stays, and higher mortality rates. Therefore, we recommend more effective seat belt awareness and education campaigns, the enforcement of current seat belt laws, their extension to all vehicle occupants, and the adoption of proven interventions that will assure sustained

International survey of seat belt use exemptions.

Science.gov (United States)

Weiss, H; Sirin, H; Levine, J A; Sauber, E

2006-08-01

Substantial evidence of seatbelt efficacy has been shown by several studies, and it is widely recommended that motor vehicle occupants use properly fitted seat belts. However, some (but a heretofore unknown number of) countries with national seat belt laws permit various exemptions which may lower use rates. The aim of this study was to survey the variety of exemptions to national seat belt laws. This investigation relied on identifying respondents from national traffic safety agencies, other governmental and non-governmental organizations, Internet searches, personal contacts, and other sources. Questionnaires were deployed through a web based survey supplemented by email and postal versions. Responses were received from 30 countries of which 28 (93.7%) had a national seat belt law. About two thirds (63.7%) of the 28 national laws applied to both front and back seat passengers. The leading exemption types included vehicles made before a certain year (n = 13), antique vehicles (n = 12), military vehicles (n = 11), buses (n = 9), and emergency vehicles (n = 8). Most responding countries reported one or more specific categories of individuals as exempt including those with medical exemptions (n = 20), taxi drivers (n = 11), police (n = 9), emergency medical personnel (n = 8), physically disabled people (n = 6), and pregnant women (n = 6). Out of 26 responses to the question regarding current level of enforcement, 42.3% felt enforcement was "very good or good" and 57.7% characterized it as "fair or poor". This study represents one of the largest international traffic law surveys reported. Most national seatbelt laws offer perilous exemptions to a broad array of vehicle types and road user groups. These findings, coupled with concern over the level of enforcement in the majority of countries surveyed, suggest that international road safety efforts have a long way to go to improve coverage and enforcement of national seat belt laws.

Parents' Depressive Symptoms and Gun, Fire, and Motor Vehicle Safety Practices.

Science.gov (United States)

Morrissey, Taryn W

2016-04-01

This study examined associations between mothers' and fathers' depressive symptoms and their parenting practices relating to gun, fire, and motor vehicle safety. Using data from the Early Childhood Longitudinal Study-Birth Cohort (ECLS-B), a nationally representative sample of children birth to age five, linear probability models were used to examine associations between measures of parents' depressive symptoms and their use of firearms, smoke detectors, and motor vehicle restraints. Parents reported use of smoke detectors, motor vehicle restraints, and firearm ownership and storage. Results suggest mothers with moderate or severe depressive symptoms were 2 % points less likely to report that their child always sat in the back seat of the car, and 3 % points less likely to have at least one working smoke detector in the home. Fathers' depressive symptoms were associated with a lower likelihood of both owning a gun and of it being stored locked. Fathers' depressive symptoms amplified associations between mothers' depressive symptoms and owning a gun, such that having both parents exhibit depressive symptoms was associated with an increased likelihood of gun ownership of between 2 and 6 % points. Interventions that identify and treat parental depression early may be effective in promoting appropriate safety behaviors among families with young children.

Identification of vehicle components associated with severe thoracic injury in motor vehicle crashes: a CIREN and NASS analysis.

Science.gov (United States)

Nirula, R; Pintar, F A

2008-01-01

Thoracic trauma secondary to motor vehicle crashes (MVC) continues to be a major cause of morbidity and mortality. Specific vehicle features may increase the risk of severe thoracic injury when striking the occupant. We sought to determine which vehicle contact points were associated with an increased risk of severe thoracic injury in MVC to focus subsequent design modifications necessary to reduce thoracic injury. The National Automotive Sampling System (NASS) databases from 1993 to 2001 and the Crash Injury Research and Engineering Network (CIREN) databases from 1996 to 2004 were analyzed separately using univariate and multivariate logistic regression stratified by restraint use and crash direction. The risk of driver thoracic injury, defined as an abbreviated injury scale (AIS) of score > or =3, was determined as it related to specific points of contact between the vehicle and the driver. The incidence of severe chest injury in NASS and CIREN were 5.5% and 33%, respectively. The steering wheel, door panel, armrest, and seat were identified as contact points associated with an increased risk of severe chest injury. The door panel and arm rest were consistently a frequent cause of severe injury in both the NASS and CIREN data. Several vehicle contact points, including the steering wheel, door panel, armrest and seat are associated with an increased risk of severe thoracic injury when striking the occupant. These elements need to be further investigated to determine which characteristics need to be manipulated in order to reduce thoracic trauma during a crash.

Modeling and Analysis of Static and Dynamic Characteristics of Nonlinear Seat Suspension for Off-Road Vehicles

OpenAIRE

Yan, Zhenhua; Zhu, Bing; Li, Xuefei; Wang, Guoqiang

2015-01-01

Low-frequency vibrations (0.5–5 Hz) that harm drivers occur in off-road vehicles. Thus, researchers have focused on finding methods to effectively isolate or control low-frequency vibrations. A novel nonlinear seat suspension structure for off-road vehicles is designed, whose static characteristics and seat-human system dynamic response are modeled and analyzed, and experiments are conducted to verify the theoretical solutions. Results show that the stiffness of this nonlinear seat suspension...

Availability, functionality, and use of seat belts in Beijing taxis prior to the 2008 Beijing Olympic Games.

Science.gov (United States)

Fleiter, Judy J; Gao, Liping; Qiu, Chen; Shi, Kan

2009-03-01

Use of driver seat belts and availability and functionality of passenger seat belts in a convenience sample of 231 Beijing taxis were examined in the months prior to the 2008 Beijing Olympic Games. Driver and front passenger seat belt use was mandated in China from 2004 to help address the growing public health crisis of road trauma. Results from observations made by in-vehicle passengers revealed that 21.2% of drivers were correctly wearing a belt, approximately half were not, and one third were using the belt in a non-functional way. Over 3/4 of this sample of taxi drivers were unrestrained while working. The percentage of functionally available belts was higher for front than rear passengers (88.3% and 22.9%, respectively). This low rate of belt availability in rear seats calls into question the preparedness of the fleet to cater for the safety needs of foreign visitors to China, particularly those from countries with high levels of restraint use. Factors influencing the use/misuse of seat belts in China remain largely unexplored. Results of this pilot study support further investigations of barriers to using injury prevention mechanisms such as seat belts in less motorised countries.

Estimated medical cost savings in Massachusetts by implementation of a primary seat belt law

Science.gov (United States)

2008-12-01

This report examines 2006 hospital discharge data reporting cases where the external cause of injury to a vehicle occupant was a motor vehicle crash to predict the estimated savings to Massachusetts if a primary seat belt law is implemented. The savi...

Motor Vehicle Theft. Special Report.

Science.gov (United States)

Harlow, Caroline Wolf

Thirteen years of data from the National Crime Survey were analyzed to examine the characteristics of motor vehicle theft, to identify trends during the past 13 years, and to determine who are most likely to be victims of motor vehicle theft. All motor vehicle thefts reported to the National Crime Survey from 1973 through 1985 were examined.…

Estimated medical cost savings in Utah by implementation of a primary seat belt law

Science.gov (United States)

2010-05-01

This report examines 2007 hospital discharge data reporting cases where the external cause of injury to : a vehicle occupant was a motor vehicle crash to predict the estimated savings to Utah if a primary seat : belt law is implemented. The savings a...

Estimated medical cost savings in Nevada by implementation of a primary seat belt law

Science.gov (United States)

2008-09-01

This report examines 2007 hospital discharge data reporting cases where the external cause of injury to a vehicle occupant was a motor vehicle crash to predict the estimated savings to Nevada if a primary seat belt law is implemented. The savings are...

Estimated medical cost savings in Vermont by implementation of a primary seat belt law

Science.gov (United States)

2008-09-01

This report examines 2005 hospital discharge data reporting cases where the external cause of injury to a vehicle occupant was a motor vehicle crash to predict the estimated savings to the State of Vermont if a primary seat belt law is implemented. T...

Estimated medical cost savings in Rhode Island by implementation of a primary seat belt law

Science.gov (United States)

2008-09-01

This report examines 2006 hospital discharge data reporting cases where the external cause of injury to a vehicle occupant was a motor vehicle crash to predict the estimated savings to Rhode Island if a primary seat belt law is implemented. The savin...

75 FR 76692 - Federal Motor Vehicle Safety Standards; Small Business Impacts of Motor Vehicle Safety

Science.gov (United States)

2010-12-09

..., 510, 511, 512, 520, 523, 525, 526, and 571 [Docket No. NHTSA-2010-0159] Federal Motor Vehicle Safety Standards; Small Business Impacts of Motor Vehicle Safety AGENCY: National Highway Traffic Safety... that specifically relate to passenger cars, multipurpose passenger vehicles, trucks, buses, trailers...

Ejection of a rear facing, golf cart passenger.

Science.gov (United States)

Schau, Kyle; Masory, Oren

2013-10-01

The following report details the findings of a series of experiments and simulations performed on a commercially available, shuttle style golf cart during several maneuvers involving rapid accelerations of the vehicle. It is determined that the current set of passive restraints on these types of golf carts are not adequate in preventing ejection of a rear facing passenger during rapid accelerations in the forward and lateral directions. Experimental data and simulations show that a hip restraint must be a minimum of 13 in. above the seat in order to secure a rear facing passenger during sharp turns, compared to the current restraint height of 5 in. Furthermore, it is determined that a restraint directly in front of the rear facing passenger is necessary to prevent ejection. In addressing these issues, golf cart manufacturers could greatly reduce the likelihood of injury due to ejection of a rear facing, golf cart passenger. Copyright © 2013 Elsevier Ltd. All rights reserved.

47 CFR 32.2112 - Motor vehicles.

Science.gov (United States)

2010-10-01

... 47 Telecommunication 2 2010-10-01 2010-10-01 false Motor vehicles. 32.2112 Section 32.2112... FOR TELECOMMUNICATIONS COMPANIES Instructions for Balance Sheet Accounts § 32.2112 Motor vehicles. This account shall include the original cost of motor vehicles of the type which are designed and...

36 CFR 261.13 - Motor vehicle use.

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Motor vehicle use. 261.13... General Prohibitions § 261.13 Motor vehicle use. After National Forest System roads, National Forest... have been identified on a motor vehicle use map, it is prohibited to possess or operate a motor vehicle...

Bringing up the rear: new premotor interneurons add regional complexity to a segmentally distributed motor pattern

Science.gov (United States)

Norris, Brian J.; Doloc-Mihu, Anca; Calabrese, Ronald L.

2011-01-01

Central pattern generators (CPGs) pace and pattern many rhythmic activities. We have uncovered a new module in the heartbeat CPG of leeches that creates a regional difference in this segmentally distributed motor pattern. The core CPG consists of seven identified pairs and one unidentified pair of heart interneurons of which 5 pairs are premotor and inhibit 16 pairs of heart motor neurons. The heartbeat CPG produces a side-to-side asymmetric pattern of activity of the premotor heart interneurons corresponding to an asymmetric fictive motor pattern and an asymmetric constriction pattern of the hearts with regular switches between the two sides. The premotor pattern progresses from rear to front on one side and nearly synchronously on the other; the motor pattern shows corresponding intersegmental coordination, but only from segment 15 forward. In the rearmost segments the fictive motor pattern and the constriction pattern progress from front to rear on both sides and converge in phase. Modeling studies suggested that the known inhibitory inputs to the rearmost heart motor neurons were insufficient to account for this activity. We therefore reexamined the constriction pattern of intact leeches. We also identified electrophysiologically two additional pairs of heart interneurons in the rear. These new heart interneurons make inhibitory connections with the rear heart motor neurons, are coordinated with the core heartbeat CPG, and are dye-coupled to their contralateral homologs. Their strong inhibitory connections with the rearmost heart motor neurons and the small side-to-side phase difference of their bursting contribute to the different motor and beating pattern observed in the animal's rear. PMID:21775711

78 FR 32223 - Control of Air Pollution From Motor Vehicles: Tier 3 Motor Vehicle Emission and Fuel Standards

Science.gov (United States)

2013-05-29

...-OAR-2011-0135; FRL-9818-5] RIN 2060-A0 Control of Air Pollution From Motor Vehicles: Tier 3 Motor... extension of the public comment period for the proposed rule ``Control of Air Pollution from Motor Vehicles: Tier 3 Motor Vehicle Emission and Fuel Standards'' (the proposed rule is hereinafter referred to as...

High levels of incorrect use of car seat belts and child restraints in Fife--an important and under-recognised road safety issue.

Science.gov (United States)

Campbell, H; Macdonald, S; Richardson, P

1997-03-01

To pilot data collection instruments and to make a preliminary estimate of the level of incorrect use of car seat belts and child restraints in Fife, Scotland. Cross sectional survey of cars containing adults and children at a number of public sites across Fife in 1995 to assess use of car occupant restraints. Trained road safety officers assessed whether seat restraints were appropriate for the age of the passengers and whether restraints were used correctly. These assessments were based on standards published by the Child Accident Prevention Trust. The survey gathered data from 596 occupants in 180 cars: 327 adults and 269 children. Ten per cent of drivers who were approached refused to participate. Car occupant restraint was assessed in 180 drivers, 151 front seat passengers, and 265 rear seat passengers. Three hundred and sixty one occupants wore seat belts, 68 were restrained by a seat belt and booster cushion, 63 in toddler seats, 25 in two way seats, and 18 in rear facing infant carriers. Ninety seven per cent of drivers, 95% of front seat passengers, and 77% of rear seat passengers were restrained. However, in 98 (52%) vehicles at least one passenger was restrained by a device that was used incorrectly. Seven per cent of adults and 28% of children were secured incorrectly. The commonest errors were loose seat belts and restraint devices not adequately secured to the seat. Rates of incorrect use were highest in child seat restraints, reaching 60% with two way seats and 44% with rear facing infant seats. The incorrect use of car occupant restraints is an under-recognised problem, both by health professionals, and the general public. Incorrect use has been shown to reduce the effectiveness of restraints, can itself result in injury, and is likely to be an important factor in child passenger injuries. The correct use of car seat restraints merits greater attention in strategies aiming to reduce road traffic casualties. Areas of intervention that could be

33 CFR 127.1311 - Motor vehicles.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Motor vehicles. 127.1311 Section... Waterfront Facilities Handling Liquefied Hazardous Gas Operations § 127.1311 Motor vehicles. (a) When LHG is... operator shall ensure that no person— (1) Stops or parks a motor vehicle in a space other than a designated...

Severe abdominal injuries sustained in an adult wearing a pelvic seatbelt: a case report and review of the literature.

LENUS (Irish Health Repository)

O'Kelly, F

2008-12-01

In automobile accidents, the "seatbelt syndrome" (SBS) consists of a constellation of injuries, predominantly involving thoraco-lumbar vertebral fractures and intraabdominal organ injury. A recent amendment to Irish legislation has made the wearing of seatbelts mandatory for all rear seated passengers in an effort to protect children. Whilst rear seatbelts result in a significant reduction in morbidity and mortality following road traffic accidents (RTA), we present a case in which the rear lap seatbelt caused severe abdominal injuries. It is evident that the current rear seat lapbelt system is an inferior design associated with a significant morbidity and mortality when compared to three-point harness system and consideration should be given to replacing them in all motor vehicles.

Vehicle seat design : state of the art and recent development

NARCIS (Netherlands)

Tan, C.F.; Delbressine, F.L.M.; Rauterberg, G.W.M.; Mokhtar, A.S.; Abdullah, E.J.; Adam, N.M.

2007-01-01

Seats are one of the most important components of vehicles and they are the place where professional driver spend most of their time. For example, according to Occupational Outlook Handbook by United State Department of Labor, the truck drivers frequently work 50 or more hours a week. The truck

[Use of seat belts and mobile phone while driving in Florence: trend from 2005 to 2009].

Science.gov (United States)

Lorini, Chiara; Pellegrino, Elettra; Mannocci, Federico; Allodi, Guendalina; Indiani, Laura; Mersi, Anna; Petrioli, Giuseppe; Santini, Maria Grazia; Garofalo, Giorgio; Bonaccorsi, Guglielmo

2012-01-01

to evaluate the trend over time of the use of seat belts by drivers and passengers of cars and vans and the use of hand held mobile phone while driving in Florence from 2005 to 2009. DESIGN, SETTING AND PARTICIPANTS AND MAIN OUTCOME MEASURES: direct observations (58,773 vehicles) have been conducted to detect the use of seat belts by occupants of cars and vans, and the use of mobile phone while driving. It has been carried out correlation analysis between the use of the seat belt by occupants of vehicles and between the simultaneous use of this device and mobile phone while driving.Moreover, it has been carried out time series analysis (ARIMA Box Jenkins) of in the prevalence of the use of seat belts by occupants of vehicles observed, of mobile phone by drivers and the trend of the risk to drive using the mobile phone with unfastened seat belt rather than to drive using the mobile phone with fastened seat belt. seat belts were used on average by 75.7% of drivers, 75.5% of front passengers and 25.1% of rear passengers. The average mobile phone use while driving was 4.5%. Drivers most frequently fasten seat belt if front passengers use it and while they do not use mobile phone. The use of seat belts by drivers and front passengers has not changed over time, whereas the use of mobile phone while driving has significantly increased. The prevalence of using mobile phone with unfastened seat belt rather than to use it with fastened seat belt while driving has significantly decreased over the years, indicating an increase in the use of mobile phone, especially among those who fasten the seat belt. it is necessary to plan and realize stronger interventions in the whole area.

40 CFR 79.33 - Motor vehicle diesel fuel.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Motor vehicle diesel fuel. 79.33... diesel fuel. (a) The following fuels commonly or commercially known or sold as motor vehicle diesel fuel are hereby individually designated: (1) Motor vehicle diesel fuel, grade 1-D; (2) Motor vehicle diesel...

40 CFR 85.1703 - Definition of motor vehicle.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Definition of motor vehicle. 85.1703... (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Exclusion and Exemption of Motor Vehicles and Motor Vehicle Engines § 85.1703 Definition of motor vehicle. (a) For the purpose of determining the...

32 CFR 935.139 - Motor vehicle operator qualifications.

Science.gov (United States)

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Motor vehicle operator qualifications. 935.139... AND INSULAR REGULATIONS WAKE ISLAND CODE Motor Vehicle Code § 935.139 Motor vehicle operator qualifications. (a) No person may operate a privately owned motor vehicle on Wake Island unless he has an island...

Ispitivanje piropatrona i raketnog motora pilotskog sedišta / Testing pyrocartridges and the rocket motor of the ejection seat

Directory of Open Access Journals (Sweden)

Milorad Savković

2008-04-01

Full Text Available Raketni motor pilotskog sedišta ima složen geometrijski oblik, tako da njegov potisak deluje pod određenim uglom u odnosu na ravan simetrije pilotskog sedišta. Radi određivanja intenziteta i napadne linije potiska izvršen je veći broj eksperimenata. Meren je potisak raketnog motora na višekomponentnom opitnom stolu. Letno ispitivanje pilotskog sedišta obavljeno je pomoću lutke koja simulira masu pilota. Takođe, analizirano je letno ispitivanje pilotskog sedišta u početnom periodu katapultiranja za vreme rada raketnog motora. Obrađeni su i rezultati merenja ubrzanja, koji su korišćeni za određivanje karakteristika leta pilotskog sedišta. U radu je prikazan teorijski model kretanja sedišta. / Due to a complex geometrical shape of the rocket motor of the ejection seat, the rocket motor thrust occurs under certain angle in relation to the plane of symmetry of the ejection seat. A number of tests were carried out in order to determine thrust intensity and angle of attack. The rocket motor thrust was measured on the multicomponent test stand. The ejection seat whit a dummy simulating a mass of a pilot was tested during ejection. The paper presents an analysis of the ejection seat flight in the initial phase of ejection, during the rocket motor running. The results of the acceleration read-outs were processed and then used for the determination of the characteristics of the ejection seat flight. A theoretical model of the ejection seat flight is given in the paper.

Optimization of geometry of annular seat valves suitable for Digital Displacement fluid power pumps/motors

DEFF Research Database (Denmark)

Rømer, Daniel; Johansen, Per; Pedersen, Henrik C.

2013-01-01

Digital Displacement Fluid Power is an upcoming technology setting new standards for the achievable efficiency of fluid power pumps and motors. The core element of the Digital Displacement technology is high performance electronically controlled seat valves, which must exhibit very low flow...... work an annular seat valve suitable for use in Digital Displacement units is considered, and the ring geometry is optimized using finite element analysis including non-linear material behaviour, contact elements and fluid pressure penetrating load, closely reflecting the actual load of the seat valve...

Presentation of electric motor and motor control technology for electric vehicles and hybrid vehicles; Denki jidosha hybrid sha yo motor oyobi motor seigyo gijutsu no shokai

Energy Technology Data Exchange (ETDEWEB)

Matsudaira, N.; Masakik, R.; Tajima, F. [Hitachi, Ltd., Tokyo (Japan)

1999-02-01

The authors have developed a motor drive system for electric vehicles and hybrid vehicles. This system consists of a permanent magnet type synchronous motor, an inverter using insulated gate bipolar transistors (IGBTs) and a controller based on a single-chip microcomputer. To achieve a compact and light weight synchronous motor, an internal permanent magnet type rotor structure was designed. This paper presents motor control technology for electric vehicles, such as an optimization method of field weakening control and a new current control method. (author)

41 CFR 101-25.402 - Motor vehicles.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Motor vehicles. 101-25.402 Section 101-25.402 Public Contracts and Property Management Federal Property Management... Standards § 101-25.402 Motor vehicles. Replacement of motor vehicles shall be in accordance with the...

49 CFR 574.9 - Requirements for motor vehicle dealers.

Science.gov (United States)

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Requirements for motor vehicle dealers. 574.9... RECORDKEEPING § 574.9 Requirements for motor vehicle dealers. (a) Each motor vehicle dealer who sells a used motor vehicle for purposes other than resale, who leases a motor vehicle for more than 60 days, that is...

Potential Occupant Injury Reduction in Pre-Crash System Equipped Vehicles in the Striking Vehicle of Rear-end Crashes.

Science.gov (United States)

Kusano, Kristofer D; Gabler, Hampton C

2010-01-01

To mitigate the severity of rear-end and other collisions, Pre-Crash Systems (PCS) are being developed. These active safety systems utilize radar and/or video cameras to determine when a frontal crash, such as a front-to-back rear-end collisions, is imminent and can brake autonomously, even with no driver input. Of these PCS features, the effects of autonomous pre-crash braking are estimated. To estimate the maximum potential for injury reduction due to autonomous pre-crash braking in the striking vehicle of rear-end crashes, a methodology is presented for determining 1) the reduction in vehicle crash change in velocity (ΔV) due to PCS braking and 2) the number of injuries that could be prevented due to the reduction in collision severity. Injury reduction was only performed for belted drivers, as unbelted drivers have an unknown risk of being thrown out of position. The study was based on 1,406 rear-end striking vehicles from NASS / CDS years 1993 to 2008. PCS parameters were selected from realistic values and varied to examine the effect on system performance. PCS braking authority was varied from 0.5 G's to 0.8 G's while time to collision (TTC) was held at 0.45 seconds. TTC was then varied from 0.3 second to 0.6 seconds while braking authority was held constant at 0.6 G's. A constant braking pulse (step function) and ramp-up braking pulse were used. The study found that automated PCS braking could reduce the crash ΔV in rear-end striking vehicles by an average of 12% - 50% and avoid 0% - 14% of collisions, depending on PCS parameters. Autonomous PCS braking could potentially reduce the number of injured drivers who are belted by 19% to 57%.

40 CFR 79.32 - Motor vehicle gasoline.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Motor vehicle gasoline. 79.32 Section...) REGISTRATION OF FUELS AND FUEL ADDITIVES Designation of Fuels and Additives § 79.32 Motor vehicle gasoline. (a) The following fuels commonly or commercially known or sold as motor vehicle gasoline are hereby...

Electric Motors for Vehicle Propulsion

OpenAIRE

Larsson, Martin

2014-01-01

This work is intended to contribute with knowledge to the area of electic motorsfor propulsion in the vehicle industry. This is done by first studying the differentelectric motors available, the motors suitable for vehicle propulsion are then dividedinto four different types to be studied separately. These four types are thedirect current, induction, permanent magnet and switched reluctance motors. Thedesign and construction are then studied to understand how the different typesdiffer from ea...

32 CFR 935.51 - Motor vehicle violations.

Science.gov (United States)

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Motor vehicle violations. 935.51 Section 935.51... REGULATIONS WAKE ISLAND CODE Penalties § 935.51 Motor vehicle violations. Whoever is found guilty of a... than 30 days, or suspension or revocation of his motor vehicle operator's permit, or any combination or...

Motor Vehicle Crash Injuries PSA (:60)

Centers for Disease Control (CDC) Podcasts

This 60 second Public Service Announcement is based on the October 2014 CDC Vital Signs report. Motor vehicle crashes are costly and preventable. Learn what can be done to help prevent motor vehicle injuries.

32 CFR 935.140 - Motor vehicle maintenance and equipment.

Science.gov (United States)

2010-07-01

... 32 National Defense 6 2010-07-01 2010-07-01 false Motor vehicle maintenance and equipment. 935.140... AND INSULAR REGULATIONS WAKE ISLAND CODE Motor Vehicle Code § 935.140 Motor vehicle maintenance and equipment. (a) Each person who has custody of a motor vehicle on Wake Island shall present that vehicle for...

2008 South Dakota motor vehicle traffic crash summary

Science.gov (United States)

2009-06-01

The Motor Vehicle Traffic Crash Summary is divided into two main sections, Historical : Trends and 2008 Motor Vehicle Traffic Crash Profile. The Historical Trend section : provides information on alcohol involvement in motor vehicle crashes, severity...

2009 South Dakota motor vehicle traffic crash summary

Science.gov (United States)

2010-06-01

The Motor Vehicle Traffic Crash Summary is divided into two main sections, Historical : Trends and 2009 Motor Vehicle Traffic Crash Profile. The Historical Trend section : provides information on alcohol involvement in motor vehicle crashes, severity...

Management of cervical spine injuries in young children: lessons learned.

Science.gov (United States)

Smith, Jodi L; Ackerman, Laurie L

2009-07-01

Previous studies have shown that the correct use of car safety seats can protect infants and children from vehicular injury. Although child passenger devices are increasingly used in the US, motor vehicle crashes continue to be the leading cause of death and acquired disability in infants and children younger than 14 years of age. These events are likely related, at least in part, to the high percentage of children who are unrestrained or improperly restrained. The authors present 2 cases of severe cervical spine trauma in young children restrained in car safety seats during a motor vehicle crash: 1) a previously healthy 14-month-old girl who was improperly restrained in a forward-facing booster seat secured to the vehicle by a lap belt, and 2) a previously healthy 30-month-old girl who was a rear seat passenger restrained in a car safety seat. This study points out the unique challenges encountered in treating cervical spine injuries in infants and young children, as well as the lessons learned, and emphasizes the significance of continuing efforts to increase family and public awareness regarding the importance of appropriate child safety seat selection and use.

2010 South Dakota motor vehicle traffic crash summary

Science.gov (United States)

2011-01-01

The Motor Vehicle Traffic Crash Summary is divided into two main sections, Historical Trends and 2010 Motor Vehicle Traffic Crash Profile. The Historical Trend section provides information on alcohol involvement in motor vehicle crashes, severity of ...

Accidents in The Netherlands involving heavy motor vehicles : an analysis concerning underrun protection of rear ends, compared to the sides and the front ends. On behalf of RDW Vehicle Technology & Information Centre.

NARCIS (Netherlands)

Kampen, L.T.B. van

1998-01-01

In this report accident data concerning heavy vehicles (all motor vehicles with a total weight of more than 3500 kg) are studied. Special attention is given to the question whether accidents involving heavy motor vehicles gave specific reason for concern regarding other road users with respect to

49 CFR 541.5 - Requirements for passenger motor vehicles.

Science.gov (United States)

2010-10-01

... TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR VEHICLE THEFT PREVENTION STANDARD § 541.5 Requirements for passenger motor vehicles. (a) Each passenger motor vehicle subject to... 49 Transportation 6 2010-10-01 2010-10-01 false Requirements for passenger motor vehicles. 541.5...

49 CFR 392.22 - Emergency signals; stopped commercial motor vehicles.

Science.gov (United States)

2010-10-01

... REGULATIONS DRIVING OF COMMERCIAL MOTOR VEHICLES Stopped Commercial Motor Vehicles § 392.22 Emergency signals; stopped commercial motor vehicles. (a) Hazard warning signal flashers. Whenever a commercial motor vehicle... than necessary traffic stops, the driver of the stopped commercial motor vehicle shall immediately...

48 CFR 945.570-8 - Reporting motor vehicle data.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Reporting motor vehicle... Reporting motor vehicle data. (a) Contractors conducting motor vehicle operations shall forward annually (on or before December 1) to the contracting officer their plan for acquisition of motor vehicles for the...

76 FR 76481 - Denial of Motor Vehicle Defect Petition

Science.gov (United States)

2011-12-07

... similarities incorporating regenerative braking (the electric motor is used as a generator to supplement..., using a scan tool in generic mode on your vehicle could cause damage to your vehicle's electric motor... whether a motor vehicle or item of replacement equipment does not comply with an applicable motor vehicle...

19 CFR 12.80 - Federal motor vehicle safety standards.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Federal motor vehicle safety standards. 12.80...; DEPARTMENT OF THE TREASURY SPECIAL CLASSES OF MERCHANDISE Motor Vehicles and Motor Vehicle Equipment Manufactured on Or After January 1, 1968 § 12.80 Federal motor vehicle safety standards. (a) Standards...

Motor Torque Calculations For Electric Vehicle

Directory of Open Access Journals (Sweden)

Saurabh Chauhan

2015-08-01

Full Text Available Abstract It is estimated that 25 of the total cars across the world will run on electricity by 2025. An important component that is an integral part of all electric vehicles is the motor. The amount of torque that the driving motor delivers is what plays a decisive role in determining the speed acceleration and performance of an electric vehicle. The following work aims at simplifying the calculations required to decide the capacity of the motor that should be used to drive a vehicle of particular specifications.

41 CFR 109-38.5103 - Motor vehicle utilization standards.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Motor vehicle... AVIATION, TRANSPORTATION, AND MOTOR VEHICLES 38-MOTOR EQUIPMENT MANAGEMENT 38.51-Utilization of Motor Equipment § 109-38.5103 Motor vehicle utilization standards. (a) The following average utilization standards...

Market Analysis and Consumer Impacts Source Document. Part II. Review of Motor Vehicle Market and Consumer Expenditures on Motor Vehicle Transportation

Science.gov (United States)

1980-12-01

This source document on motor vehicle market analysis and consumer impacts consists of three parts. Part II consists of studies and review on: motor vehicle sales trends; motor vehicle fleet life and fleet composition; car buying patterns of the busi...

Injury patterns among obese children involved in motor vehicle collisions.

Science.gov (United States)

Haricharan, Ramanath N; Griffin, Russell L; Barnhart, Douglas C; Harmon, Carroll M; McGwin, Gerald

2009-06-01

The purpose of this study was to compare injury patterns among obese children to their nonobese counterparts involved in motor vehicle collisions. A nationwide data collection program containing occupant, collision, and injury details from police-reported tow-away crashes between 1997 and 2006 were used. Risk ratios (RRs) and associated 95% confidence intervals (CIs) were adjusted for age, sex, restraint, seat track position, vehicle curb weight, and total velocity change. An estimated 9 million children aged 2 to 17 years (20.2% obese) were involved in motor vehicle collisions during the study period. Among 2-to-5-year-olds, obesity increased the risk of severe head (RR, 3.67; 95% CI, 1.03-13.08) and thoracic (2.27; 1.01-5.08) injuries. Among 6-to-9-year-olds, obesity increased risk of thoracic (2.31; 1.08-4.95) and lower extremity (LE) injuries (1.89; 1.03-3.47). Among 10-to-13-year-olds, obesity increased the risk of severe thoracic (1.98; 1.08-3.65) and LE (6.06; 2.23-16.44) injuries. Among 14-to-17-year-olds, obesity increased risk of severe LE injuries (1.44; 1.04-2.00) but decreased risk of abdominal (0.20; 0.07-0.60) and head (0.33; 0.18-0.60) injuries, very similar to the pattern reported in obese adults. The pattern of obesity-associated injuries changes from a higher risk of head and thoracic injuries among young children to a pattern in late teenagers that is similar to obese adults.

41 CFR 109-38.5105 - Motor vehicle local use objectives.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Motor vehicle local use..., TRANSPORTATION, AND MOTOR VEHICLES 38-MOTOR EQUIPMENT MANAGEMENT 38.51-Utilization of Motor Equipment § 109-38.5105 Motor vehicle local use objectives. (a) Individual motor vehicle utilization cannot always be...

Factors Associated With Poor Child Motor Vehicle Restraint on the USA-Mexico Border.

Science.gov (United States)

Schrodt, Alexander; Huynh, Tam; Fitzgerald, Tamara N

Motor vehicle collisions (MVCs) are a significant cause of pediatric morbidity, particularly in low- to middle-income countries. We describe car seat use in children on the USA-Mexico border. A retrospective review was conducted for children 0-9 years old, admitted to the region's only Level I trauma center. Simultaneously, data were obtained from the SAFE KIDS database, a program that encourages car seat use through city checkpoints. There were 250 MVC admissions and nine fatalities in children 0-9 years old from 2010 to 2015. Nine percent of MVCs occurred in Mexico and 49% in El Paso, TX. Comparing trauma admissions to SAFE KIDS, there was some correlation between the location of MVCs and screening checkpoints (r = .50). There was a weaker correlation between injured children's neighborhoods and screening locations (r = .32). Only 37% of parents knew the crash history of the car seat and 3% were using a car seat previously involved in an MVC. While 96% of inspected children were placed appropriately in the backseat, 80% of children were found to be inappropriately restrained. Younger children more likely to be restrained (p < .05). Children from New Mexico and Mexico had the lowest rates of proper restraint and the highest injury severity scores. Proper use of car seats is a public health concern on the USA-Mexico border, and children are not properly restrained. Screening may be improved by focusing where at-risk children live and where most accidents occur. Restraint education is needed, particularly in New Mexico and Mexico.

40 CFR 52.2424 - Motor vehicle emissions budgets.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Motor vehicle emissions budgets. 52... (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS (CONTINUED) Virginia § 52.2424 Motor vehicle emissions budgets. (a) Motor vehicle emissions budget for the Hampton Roads maintenance area adjusting the...

48 CFR 908.7101 - Motor vehicles.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Motor vehicles. 908.7101 Section 908.7101 Federal Acquisition Regulations System DEPARTMENT OF ENERGY COMPETITION ACQUISITION PLANNING REQUIRED SOURCES OF SUPPLIES AND SERVICES Acquisition of Special Items 908.7101 Motor vehicles. ...

Modeling and Analysis of Static and Dynamic Characteristics of Nonlinear Seat Suspension for Off-Road Vehicles

Directory of Open Access Journals (Sweden)

Zhenhua Yan

2015-01-01

Full Text Available Low-frequency vibrations (0.5–5 Hz that harm drivers occur in off-road vehicles. Thus, researchers have focused on finding methods to effectively isolate or control low-frequency vibrations. A novel nonlinear seat suspension structure for off-road vehicles is designed, whose static characteristics and seat-human system dynamic response are modeled and analyzed, and experiments are conducted to verify the theoretical solutions. Results show that the stiffness of this nonlinear seat suspension could achieve real zero stiffness through well-matched parameters, and precompression of the main spring could change the nonlinear seat suspension performance when a driver’s weight changes. The displacement transmissibility curve corresponds with the static characteristic curve of nonlinear suspension, where the middle part of the static characteristic curve is gentler and the resonance frequency of the displacement transmissibility curve and the isolation minimum frequency are lower. Damping should correspond with static characteristics, in which the corresponding suspension damping value should be smaller given a flatter static characteristic curve to prevent vibration isolation performance reduction.

40 CFR 52.244 - Motor vehicle emissions budgets.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Motor vehicle emissions budgets. 52.244... (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS California § 52.244 Motor vehicle emissions budgets. (a) Approval of the motor vehicle emissions budgets for the following ozone rate-of-progress and...

40 CFR 69.51 - Motor vehicle diesel fuel.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Motor vehicle diesel fuel. 69.51... (CONTINUED) SPECIAL EXEMPTIONS FROM REQUIREMENTS OF THE CLEAN AIR ACT Alaska § 69.51 Motor vehicle diesel... motor vehicle diesel fuel standards and dye provisions under 40 CFR 80.520 and associated requirements...

28 CFR 29.8 - Motor vehicle owner participation.

Science.gov (United States)

2010-07-01

... 28 Judicial Administration 1 2010-07-01 2010-07-01 false Motor vehicle owner participation. 29.8 Section 29.8 Judicial Administration DEPARTMENT OF JUSTICE MOTOR VEHICLE THEFT PREVENTION ACT REGULATIONS § 29.8 Motor vehicle owner participation. In order to participate in this program, the owner(s) of a...

40 CFR 52.2311 - Motor vehicle antitampering.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Motor vehicle antitampering. 52.2311... (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS (CONTINUED) Texas § 52.2311 Motor vehicle... Emissions from Motor Vehicles” and 114.5 “Exclusions and Exceptions” on February 24, 1989, and September 6...

48 CFR 908.7101-4 - Replacement of motor vehicles.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Replacement of motor....7101-4 Replacement of motor vehicles. (a) The replacement of motor vehicles shall be in accordance with... Heads of Contracting Activities may arrange to sell, as exchange sales, used motor vehicles being...

48 CFR 945.570-7 - Disposition of motor vehicles.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Disposition of motor... Disposition of motor vehicles. (a) The contractor shall dispose of DOE-owned motor vehicles as directed by the contracting officer. (b) DOE-owned motor vehicles may be disposed of as exchange/sale items when directed by...

Compliance with Seat Belt Use in Makurdi, Nigeria: An ...

African Journals Online (AJOL)

Background: Seat belts are designed to reduce injuries due to road crash among vehicle occupants. Aims: This study aims to determine the availability of seat belt in vehicles and compliance with seat belt use among vehicle occupants. Materials and methods: This was a 24‑h direct observational study of seat belt usage ...

Variable-Reluctance Motor For Electric Vehicles

Science.gov (United States)

Lang, Jeffrey H.

1987-01-01

Report describes research on variable-reluctance electric-motor drive for eventual use in electric-vehicle propulsion. Primary design and performance criteria were torque and power output per unit mass of motor, cost, and drive efficiency. For each criterion, optimized drive design developed, and designs unified to yield single electric-vehicle drive. Scaled-down motor performed as expected. Prototype of paraplegic lift operated by toggle switch and joystick. Lift plugs into household electrical outlet for recharging when not in use.

40 CFR 85.1715 - Aircraft meeting the definition of motor vehicle.

Science.gov (United States)

2010-07-01

... motor vehicle. 85.1715 Section 85.1715 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Motor Vehicles and Motor Vehicle Engines § 85.1715 Aircraft meeting the definition of motor vehicle. This section applies for aircraft meeting the definition of motor vehicle in § 85.1703. (a) For the...

The influence of occupant anthropometry and seat position on ejection risk in a rollover.

Science.gov (United States)

Atkinson, Theresa; Fras, Andrew; Telehowski, Paul

2010-08-01

During rollover crashes, ejection increases an occupant's risk of severe to fatal injury as compared to risks for those retained in the vehicle. The current study examined whether occupant anthropometry might influence ejection risk. Factors such as restraint use/disuse, seating position, vehicle type, and roll direction were also considered in the analysis. The current study examined occupant ejections in 10 years of National Automotive Sampling System (NASS) single-event rollovers of passenger vehicles and light trucks. Statistical analysis of unweighted and weighted ejection data was carried out. No statistically significant differences in ejection rates were found based on occupant height, age, or body mass index. Drivers were ejected significantly more frequently than other occupants: 62 percent of unrestrained drivers were ejected vs. 51 percent unrestrained right front occupants. Second row unrestrained occupants were ejected at rates similar to right front-seated occupants. There were no significant differences in ejection rates for near- vs. far-side occupants. These data suggest that assessment of ejection prevention systems using either a 50th or 5th percentile adult anthropomorphic test dummy (ATD) might provide a reasonable measure of system function for a broad range of occupants. They also support the development of ejection mitigation technologies that extend beyond the first row to protect occupants in rear seat positions. Future studies should consider potential interaction effects (i.e., occupant size and vehicle dimensions) and the influence of occupant size on ejection risk in non-single-event rollovers.

Motor Vehicle Safety

Science.gov (United States)

... these crashes is one part of motor vehicle safety. Here are some things you can do to ... speed or drive aggressively Don't drive impaired Safety also involves being aware of others. Share the ...

Vital Signs-Motor Vehicle Crash Injuries

Centers for Disease Control (CDC) Podcasts

2014-10-07

This podcast is based on the October 2014 CDC Vital Signs report. Motor vehicle crashes are costly and preventable. Learn what can be done to help prevent motor vehicle injuries.  Created: 10/7/2014 by National Center for Chronic Disease Prevention and Health Promotion (NCCDPHP).   Date Released: 10/7/2014.

Vehicle Lateral Control Under Fault in Front and/or Rear Sensors: Final Report

OpenAIRE

Lu, Guang; Huang, Jihua; Tomizuka, Masayoshi

2004-01-01

This report presents the research results of Task Order 4204(TO4204), "Vehicle Lateral Control under Fault in Front and/or Rear Sensors". This project is a continuing effort of the Partners for Advanced Transit and Highways (PATH) on the research of passenger vehicles for Automated Highway Systems (AHS).

78 FR 43964 - BMW of North America, LLC, a Subsidiary of BMW AG, Grant of Petition for Decision of...

Science.gov (United States)

2013-07-22

... capacity (expressed in terms of total number of occupants and number of occupants for each front and rear... in fact it should be ``3,'' and the total designated seating capacity as ``4'' when in fact it should... inconsequential to motor vehicle safety, and that its petition, to exempt from providing recall notification of...

Motor Vehicle Crash Injuries PSA (:60)

Centers for Disease Control (CDC) Podcasts

2014-10-07

This 60 second Public Service Announcement is based on the October 2014 CDC Vital Signs report. Motor vehicle crashes are costly and preventable. Learn what can be done to help prevent motor vehicle injuries.  Created: 10/7/2014 by National Center for Injury Prevention and Control (NCIPC).   Date Released: 10/7/2014.

Hybrid vehicle motor alignment

Science.gov (United States)

Levin, Michael Benjamin

2001-07-03

A rotor of an electric motor for a motor vehicle is aligned to an axis of rotation for a crankshaft of an internal combustion engine having an internal combustion engine and an electric motor. A locator is provided on the crankshaft, a piloting tool is located radially by the first locator to the crankshaft. A stator of the electric motor is aligned to a second locator provided on the piloting tool. The stator is secured to the engine block. The rotor is aligned to the crankshaft and secured thereto.

Seat belt and mobile phone use among vehicle drivers in the city of Doha, Qatar: an observational study.

Science.gov (United States)

Mahfoud, Ziyad R; Cheema, Sohaila; Alrouh, Hekmat; Al-Thani, Mohammed Hamad; Al-Thani, Al Anoud Mohammed; Mamtani, Ravinder

2015-09-22

In Qatar traffic injuries and fatalities are of serious concern. Mobile phone use whilst driving has been associated with increased risk of vehicular collisions and injuries. Seat belt use has been demonstrated to save lives and reduce the severity of road traffic injuries. Whereas previously published studies may have looked at all front passengers, this study aims to obtain reliable estimates of the prevalence of seat belt and mobile phone use among vehicle drivers in the city of Doha, Qatar. Additionally, we aim to investigate the association of these behaviors with other variables namely gender, time of the day and type of vehicle. An observational study on 2,011 vehicles was conducted in 2013. Data were collected at ten sites within Doha city over a two-week period. Two trained observers surveyed each car and recorded observations on a data collection form adapted from a form used in a 2012 Oklahoma observational study. Associations were assessed using the Chi-squared test or Fisher's exact test. A p-value of .05 or less was considered statistically significant. Overall, 1,463 (72.7 %) drivers were found using a seat belt (95 % CI: 70.8-74.7 %) and 150 (7.5 %) their mobile phones (95 % CI: 6.3-8.6 %) during the observation period. Mobile phone use was significantly associated with not using a seat belt and driving a sport utility vehicle. Significantly lower rates of seat belt use were observed in the early morning and late afternoon. No gender differences were observed. Seatbelt use in Doha was found to be similar to countries in the region but lower than those in western countries. Also, studies from other high-income locations, reported lower rates of mobile phone use while driving than in Doha. Despite road traffic crashes being one of the leading causes of death in Qatar, three out of 10 drivers in Doha, Qatar, do not use a seat belt and about one in 12 use a mobile phone while driving. More efforts, in the form of awareness campaigns and increased law

Air pollution from motor vehicle emissions

International Nuclear Information System (INIS)

Petrushevska, Ljubica

1996-01-01

This paper presents some aspects of air pollution from motor vehicle emissions as: characteristic primary and secondary pollutants, dependence of the motor vehicle emission from the engine type; the relationship of typical engine emission and performance to air-fuel ratio, transport of pollutants from mobile sources of emissions, as well as some world experiences in the control approaches for exhaust emissions. (author)

Attitudes towards child restrains and seat belts usage in the learned population of Karachi, Pakistan.

Science.gov (United States)

Siddiqui, Emaduddin; Ejaz, Kiran; Waheed, Shahan; Kazi, Ghazala Irfan; Khursheed, Munawar

2014-01-01

Motor vehicles crashes (MVCs) are the leading cause of injury related morbidity and mortality in developed countries. Recent evidence proves that properly used child seat belts can dramatically reduce the risk of severe and life-threatening injury from MVCs. There are rarities of thought and inspiration regarding the use of child seat belts in our society and region, therefore we lack of data regarding factors and paucity of usage of child seat belts in motor vehicles. This study aimed to assess the knowledge and attitudes of child seat belt usage among the educated population in Karachi, Pakistan. Altogether 304 employees were investigated. They were employees of Aga Khan University who were using their cars and having children younger than 10 years old. A cross sectional observational study was designed, and a 36-item questionnaire in English was used to collect data on participants' demographic details, designation, educational level, economic status, validity of driving license, number of children and cars, availability of adult seat belts and child seat belts along with their functionality, awareness, knowledge and attitude toward its use, and reason of not using these devices. SPSS version 20 for Windows was used to analyze the data and the Chi-square test was used. Totally 290 participants were recruited with a response rate of 72% (212). Of 212 participants, 126 (59%) were male. 154 (72.6%) participants had valid driver licenses, and 154 (72.6%) had adult seat belts in their vehicles. Only 32 (15%) reported regular use of adult seat belts. Although 168 (79.2%) participants had some knowledge about child restrains (CRs), only 65 (22%) had CRs in their cars. Eighty-two (38.7%) participants got the knowledge about CRs and seat belts from media. Mothers were more concerned about the use of CRs than fathers. Only 14 (6.6%) parents were found to use both adult and child seat belts all the time. Of the 157 parents who did not us use CRs, 42 considered unnecessary

48 CFR 970.2307-1 - Motor vehicle fleet operations.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Motor vehicle fleet..., Renewable Energy Technologies, Occupational Safety and Drug-Free Work Place 970.2307-1 Motor vehicle fleet... that the Federal motor vehicle fleet will serve as an example and provide a leadership role in the...

49 CFR 567.4 - Requirements for manufacturers of motor vehicles.

Science.gov (United States)

2010-10-01

... applicable Federal motor vehicle safety, bumper, and theft prevention standards in effect on the date of... statement: “This vehicle conforms to all applicable Federal motor vehicle safety and theft prevention... conforms to the applicable Federal motor vehicle theft prevention standard in effect on the date of...

Electric vehicle motors and controllers

Science.gov (United States)

Secunde, R. R.

1981-01-01

Improved and advanced components being developed include electronically commutated permanent magnet motors of both drum and disk configuration, an unconventional brush commutated motor, and ac induction motors and various controllers. Test results on developmental motors, controllers, and combinations thereof indicate that efficiencies of 90% and higher for individual components, and 80% to 90% for motor/controller combinations can be obtained at rated power. The simplicity of the developmental motors and the potential for ultimately low cost electronics indicate that one or more of these approaches to electric vehicle propulsion may eventually displace presently used controllers and brush commutated dc motors.

40 CFR 69.52 - Non-motor vehicle diesel fuel.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Non-motor vehicle diesel fuel. 69.52... (CONTINUED) SPECIAL EXEMPTIONS FROM REQUIREMENTS OF THE CLEAN AIR ACT Alaska § 69.52 Non-motor vehicle diesel... NRLM diesel fuel. (5) Exempt NRLM diesel fuel and heating oil must be segregated from motor vehicle...

Assessment of capacity building needs among motor vehicle ...

African Journals Online (AJOL)

The motor vehicle mechanics trainers' are affected by the developments in the modern automobile technology (MAT) that brought about the use of auto scan tools for diagnosis and repair of modern vehicles in Nigeria. This study examined the capacity building needs among motor vehicle mechanics trainers in the use of ...

Motor vehicle evaluative criteria: Using unmet expectations as signals for dissonance

Directory of Open Access Journals (Sweden)

Sanjana Brijball Parumasur

2015-07-01

Full Text Available This study assesses whether motor vehicle consumers base their purchases on functional or symbolic needs. It also evaluates motor vehicle buyer’s level of importance attached to evaluative criteria and the extent to which they believe the purchased vehicle fulfils the evaluative criteria, in order to assess whether expectations have been met or not and hence, the potential for cognitive dissonance. Biographical correlates (race, marital status, age, education, occupation, income, gender are evaluated and the influence of range of motor vehicle is also analysed. A sample of 200 brand new motor vehicle buyers was drawn using the stratified random sampling technique based on range of motor vehicle purchased, month of purchases, gender and age of the buyer. Only new motor vehicle buyers (within KwaZulu-Natal who concluded their purchases in one major, reputable and leading motor vehicle manufacturing company and who owned the vehicle for a maximum period of seven months were considered, so as to avoid cognitive intrusion. The results indicate that consumer’ expectations were not met in terms of price, economy and performance yet these were buyers’ most highly rated evaluative criteria, thereby reflecting the potential for dissonance. Significant biographical correlates were noted in terms of race, age, occupation, income, gender and motor vehicle evaluative criteria. Whilst bottom and middle of the range motor vehicle consumers favour functional or utilitarian value, top of the range motor vehicle consumers aim to fulfil symbolic needs

Vehicle Lateral Control under Fault in Front and/or Rear Sensors

OpenAIRE

Huang, Jihua; Lu, Guang; Tomizuka, Masayoshi

2000-01-01

This report documents the findings of research performed under TO4204, "Vehicle Lateral Control under Fault in Front and/or Rear Sensors" during the year 2000- 2001. The research goal of TO4204 is to develop vehicle lateral control strategies under faulty operation of the magnetometers. The main objectives of the project are: (1) to design controllers that use the output from only one set of magnetometers, and (2) to develop an autonomous lateral control scheme that uses no magnetometers. New...

Alcohol Advertising and Motor Vehicle Fatalities

OpenAIRE

Henry Saffer

1994-01-01

The purpose of this paper is to empirically estimate the effect of alcohol advertising on motor vehicle fatalities. The concept of an industry level advertising response function is developed and other empirical issues in estimating the effects of advertising are reviewed. The data set consists of quarterly observations, from 1986 to 1989, for 75 advertising markets in the United States and includes 1200 observations. Since motor vehicle fatalities and alcohol advertising are jointly determin...

40 CFR 52.1159 - Enhanced Motor Vehicle Inspection and Maintenance.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Enhanced Motor Vehicle Inspection and... Enhanced Motor Vehicle Inspection and Maintenance. (a) Revisions submitted by the Massachusetts Department of Environmental Protection on October 20, 2000, to the motor vehicle inspection and maintenance...

41 CFR 109-38.301-1.53 - Responsibilities of motor vehicle operators.

Science.gov (United States)

2010-07-01

... motor vehicle operators. 109-38.301-1.53 Section 109-38.301-1.53 Public Contracts and Property... MANAGEMENT REGULATIONS AVIATION, TRANSPORTATION, AND MOTOR VEHICLES 38-MOTOR EQUIPMENT MANAGEMENT 38.3-Official Use of Government Motor Vehicles § 109-38.301-1.53 Responsibilities of motor vehicle operators...

78 FR 68748 - Federal Motor Vehicle Safety Standards; Designated Seating Positions

Science.gov (United States)

2013-11-15

... Justice (AAJ), Safety Research and Strategies (SRS), Toyota Motor North America (Toyota), Mitsubishi Motors R&D of America (Mitsubishi), and Public Citizen.\\2\\ Toyota also expressed its support for the Alliance's petition. The petitions filed by SAE International and Toyota were styled both as requests for...

41 CFR 109-38.204-50 - Records of exempted motor vehicles.

Science.gov (United States)

2010-07-01

... motor vehicles. 109-38.204-50 Section 109-38.204-50 Public Contracts and Property Management Federal... AVIATION, TRANSPORTATION, AND MOTOR VEHICLES 38-MOTOR EQUIPMENT MANAGEMENT 38.2-Registration, Identification, and Exemptions § 109-38.204-50 Records of exempted motor vehicles. The Director, Office of...

22 CFR 151.8 - Evidence of insurance for motor vehicles.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Evidence of insurance for motor vehicles. 151.8... LIABILITY INSURANCE FOR DIPLOMATIC MISSIONS AND PERSONNEL § 151.8 Evidence of insurance for motor vehicles... insurance throughout the period of registration on all motor vehicles owned or leased or otherwise regularly...

76 FR 12792 - Petition for Exemption From the Federal Motor Vehicle Motor Theft Prevention Standard; General...

Science.gov (United States)

2011-03-08

... From the Federal Motor Vehicle Motor Theft Prevention Standard; General Motors Corporation AGENCY..., Exemption from the Theft Prevention Standard. This petition is granted because the agency has determined... in reducing and deterring motor vehicle theft as compliance with the parts-marking requirements of...

77 FR 22383 - Petition for Exemption From the Federal Motor Vehicle Motor Theft Prevention Standard; TESLA

Science.gov (United States)

2012-04-13

... From the Federal Motor Vehicle Motor Theft Prevention Standard; TESLA AGENCY: National Highway Traffic... exemption. SUMMARY: This document grants in full the petition of Tesla Motors Inc's. (Tesla) for an... 49 CFR Part 541, Federal Motor Vehicle Theft Prevention Standard. Tesla requested confidential...

36 CFR 1005.4 - Commercial passenger-carrying motor vehicles.

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Commercial passenger-carrying motor vehicles. 1005.4 Section 1005.4 Parks, Forests, and Public Property PRESIDIO TRUST COMMERCIAL AND PRIVATE OPERATIONS § 1005.4 Commercial passenger-carrying motor vehicles. Passenger-carrying motor...

41 CFR 109-38.903-50 - Reporting DOE motor vehicle data.

Science.gov (United States)

2010-07-01

... AVIATION, TRANSPORTATION, AND MOTOR VEHICLES 38-MOTOR EQUIPMENT MANAGEMENT 38.9-Federal Motor Vehicle Fleet... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Reporting DOE motor vehicle data. 109-38.903-50 Section 109-38.903-50 Public Contracts and Property Management Federal...

19 CFR 10.310 - Election to average for motor vehicles.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Election to average for motor vehicles. 10.310... Free Trade Agreement § 10.310 Election to average for motor vehicles. (a) Election. In determining whether a motor vehicle is originating for purposes of the preferences under the Agreement or a Canadian...

49 CFR 178.348 - Specification DOT 412; cargo tank motor vehicle.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Specification DOT 412; cargo tank motor vehicle... SPECIFICATIONS FOR PACKAGINGS Specifications for Containers for Motor Vehicle Transportation § 178.348 Specification DOT 412; cargo tank motor vehicle. ...

49 CFR 178.347 - Specification DOT 407; cargo tank motor vehicle.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Specification DOT 407; cargo tank motor vehicle... SPECIFICATIONS FOR PACKAGINGS Specifications for Containers for Motor Vehicle Transportation § 178.347 Specification DOT 407; cargo tank motor vehicle. ...

49 CFR 178.346 - Specification DOT 406; cargo tank motor vehicle.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Specification DOT 406; cargo tank motor vehicle... SPECIFICATIONS FOR PACKAGINGS Specifications for Containers for Motor Vehicle Transportation § 178.346 Specification DOT 406; cargo tank motor vehicle. ...

Non-Invasive Detection of Respiration and Heart Rate with a Vehicle Seat Sensor.

Science.gov (United States)

Wusk, Grace; Gabler, Hampton

2018-05-08

This study demonstrates the feasibility of using a seat sensor designed for occupant classification from a production passenger vehicle to measure an occupant’s respiration rate (RR) and heart rate (HR) in a laboratory setting. Relaying occupant vital signs after a crash could improve emergency response by adding a direct measure of the occupant state to an Advanced Automatic Collision Notification (AACN) system. Data was collected from eleven participants with body weights ranging from 42 to 91 kg using a Ford Mustang passenger seat and seat sensor. Using a ballistocardiography (BCG) approach, the data was processed by time domain filtering and frequency domain analysis using the fast Fourier transform to yield RR and HR in a 1-min sliding window. Resting rates over the 30-min data collection and continuous RR and HR signals were compared to laboratory physiological instruments using the Bland-Altman approach. Differences between the seat sensor and reference sensor were within 5 breaths per minute for resting RR and within 15 beats per minute for resting HR. The time series comparisons for RR and HR were promising with the frequency analysis technique outperforming the peak detection technique. However, future work is necessary for more accurate and reliable real-time monitoring of RR and HR outside the laboratory setting.

A motor vehicle accident fatality involving the inhalation of 1,1-difluoroethane.

Science.gov (United States)

Hahn, Timothy; Avella, Joseph; Lehrer, Michael

2006-10-01

A 24-year-old female driver with a history of substance abuse was pronounced dead following a single car motor vehicle accident. A surviving front seat passenger witnessed the decedent inhaling "Dust Off" cleaner just prior to losing control of the vehicle. The propellant compound used in this product is the halogenated hydrocarbon 1,1-difluoroethane (DFE). Sealed autopsy specimens were examined for the presence and subsequent quantitation of DFE utilizing an Agilent 6850 gas chromatograph (GC)-flame-ionization detector. The levels of DFE obtained were as follows: 29.8 mg/L in femoral blood, 40.3 mg/L in pulmonary arterial blood, 85.6 mg/L in aortic blood, 79.9 mg/L in chest cavity blood, 21.2 mg/L in vitreous, 11.7 mg/kg in brain, 27.9 mg/kg in liver, 71.0 mg/L in urine, and 51.8 mg/total gastric contents. The presence of DFE was confirmed in the decedent's urine by injection on an Agilent 6890/5973 GC-mass spectrometer in full scan mode. This case presents a uniquely witnessed observation of the apparent impairing effects and consequences of the acute inhalation of halogenated hydrocarbons such as DFE and the operation of a motor vehicle. The proximity of time of death to inhalant use may also provide insight to postmortem distribution patterns of DFE in relation to normal physiologic blood flow. With further investigations, estimating the time of final use of an inhalant prior to death may be deciphered from such patterns, although a degree of caution should be applied in deaths resulting from severe trauma in which normal tissue structure is compromised because postmortem redistribution may result.

Narrative text analysis to identify technologies to prevent motor vehicle crashes: examples from military vehicles.

Science.gov (United States)

Pollack, Keshia M; Yee, Nathan; Canham-Chervak, Michelle; Rossen, Lauren; Bachynski, Kathleen E; Baker, Susan P

2013-02-01

The purpose of this research is to describe the leading circumstances of military vehicle crashes to guide prioritization and implementation of crash avoidance and/or warning technologies. A descriptive study using narrative text analysis on 3,944 military vehicle crash narratives. Crash data on drivers, from 2001 to 2006, were assembled from the U.S. Army Combat Readiness/Safety Center. Reviewers collected information on the circumstances of crashes and determined if vehicle technology could have prevented the crash. Nearly 98% of the crashes were nonfatal; 63% occurred in the U.S. and 24% in Iraq. Among crash events where the direction of the impact was recorded, 32% were to the front of the vehicle and 16% involved a vehicle being rear-ended. Rollovers were mentioned in 20% of the narratives. Technology was determined to have the potential to prevent 26% of the crashes, with the forward collision warning system, rear end collision avoidance, emergency brake assistance, and rollover stability control system likely to have the greatest impacts. Some technologies available for civilian vehicles may prevent certain military crash circumstances. The results of this research are significant in light of ongoing global military operations that rely on military vehicles. Improving the preventive technology featured on military vehicles may be an effective strategy to reduce the occurrence of military crashes. Copyright © 2013 Elsevier Ltd. All rights reserved.

Motor vehicle-related air toxics study. Final report

International Nuclear Information System (INIS)

1993-04-01

Section 202 (1)(1) of the Clean Air Act (CAA), as amended (Section 206 of the Clean Air Act Amendments) (CAAA) of 1990 added paragraph (1) to Section 202 of the (CAA), directs the Environmental Protection Agency (EPA) to complete a study by May 15, 1992 of the need for, and feasibility of, controlling emissions of toxic air pollutants which are unregulated under the Act and associated with motor vehicles and motor vehicle fuels. The report has been prepared in response to Section 202 (1)(1). Specific pollutants or pollutant categories which are discussed in the report include benezene, formaldehyde, 1,3-butadiene, acetaldehyde, diesel particulate matter, gasoline particulate matter, and gasoline vapors as well as certain of the metals and motor vehicle-related pollutants identified in Section 112 of the Clean Air Act. The focus of the report is on carcinogenic risk. The study attempts to summarize what is known about motor vehicle-related air toxics and to present all significant scientific opinion on each issue

Investigation of Vehicle Rear Under Run Protection Device (RUPD) Using Aluminium Foam

Science.gov (United States)

Nagaraj Goud, B.; pachori, Avinash

2017-08-01

Whenever the passenger cars meet with accidents with the heavy duty truck from rear, it will tend to penetrate under the truck bed called truck trailer under-ride crash. This is responsible for the thousands of accidents, causing severe injuries and spot death. This is mostly due to the lack of effective guarding system. The Present paper gives an importance on energy absorption mechanism of a Rear under Run Protection Device (RUPD) under crash effect of the truck. The aim of the study is to replace Steel RUPD with aluminum foam, which promises an improvement of vehicle crashworthiness as well as to reduce weight of the vehicle. The aluminum foam is selected due to the high specific strength and specific stiffness. This inborn character makes it a promising candidate in the modern lightweight structures in the automotive engineering which can contribute to the improvement of mileage in addition to safety of the occupants.

Motor vehicle stocks, scrappage, and sales

OpenAIRE

Alan Greenspan; Darrel Cohen

1996-01-01

This paper offers a framework for forecasting aggregate sales of new motor vehicles; this framework incorporates separate models for the change in the vehicle stock and for the rate of vehicle scrappage. Because this approach requires only a minimal set of assumptions about demographic trends, the state of the economy, consumer ''preferences,'' new vehicle prices and repair costs, and vehicle retirements, it is shown to be especially useful as a macroeconomic forecasting tool. In addition, th...

Influence of an Enforcement Campaign on Seat-Belt and Helmet Wearing, Karachi-Hala Highway, Pakistan

Science.gov (United States)

Bhatti, Junaid A.; Ejaz, Kiran; Razzak, Junaid A.; Tunio, Israr Ali; Sodhar, Irshad

2011-01-01

This study assessed to what extent an enforcement campaign influenced seat-belt and helmet wearing on a Pakistani highway. The study setting was the Karachi-Hala highway where a traffic enforcement campaign was conducted from Dec 2009 to Feb 2010. Seat-belt and helmet wearing were observed in Nov 2009 and Apr 2010 at Karachi toll plaza. Differences in wearing rates as a function of occupants’ age, sex, and vehicle type were compared between the two periods. On average, 9 119 (Standard deviation=1 896) traffic citations were issued per month from Aug 2009 to Feb 2010; 4.2% of which were for not wearing helmet. A 22.5% increase in citations was observed for Dec 2009 to Feb 2010 periods compared with Aug 2009 to Oct 2009 periods. Nearly six thousand four-wheeled and four hundred two-wheeled motorized vehicle occupants were observed in Nov 2009 and Apr 2010. Overall, two of the five drivers and one of the five front seat occupants wore seat belts. This proportion was significantly higher in drivers and front-seat occupants of cars than those of heavier vehicles. Similarly, one of two motorcyclists used a helmet but this proportion was 5.8% for pillion riders in Nov 2009. The increased enforcement had a limited influence on belt wearing in drivers (+4.0%; 95% Confidence Interval [95%CI]=1.8–6.1) and occupants (+6.2%; 95%CI=4.2–8.2). A higher increase was observed for motorcyclists (+9.8%; 95%CI=2.6–16.8) and pillion riders (+12.8%; 95%CI=5.4, 20.5). These results suggested that serious efforts are required to increase seat-belt and helmet use on Pakistani highways. Improving enforcement resources, increased fines, not allowing such vehicles on roads, and awareness campaigns targeting drivers of heavy vehicles might increase wearing rates in Pakistan. PMID:22105384

Injury severity and seating position in accidents with German EMS helicopters.

Science.gov (United States)

Hinkelbein, Jochen; Spelten, Oliver; Neuhaus, Christopher; Hinkelbein, Mandy; Özgür, Enver; Wetsch, Wolfgang A

2013-10-01

Accident rates and fatality rates for Helicopter Emergency Medical Service (HEMS) missions have been investigated recently, but none of these studies considered the influence of the seating position in the helicopter. The aim of the present descriptive and observational study was to analyze injury severity depending on the seating position during HEMS accidents in Germany. Data from the German Federal Agency for Flight Accident Investigation was gathered for a period of 40 years (from 1970 to 2009). The seating position in the aircraft during the accident and the resulting injury severity (i.e., 1=no; 2=slight; 3=severe; and 4=fatal) were recorded. Injury severity was compared using the Fisher's exact test. P values accidents were investigated (n=61 accidents did not lead to any injuries in the occupants, n=7 accidents resulted in minor, and n=6 in severe injuries, and lethal injuries resulted from n=15 accidents). The occupant in the "patient" position was most likely to suffer from deadly injuries (44.9%), followed by the HEMS crew member rear seat (25.0%), compared to lower lethality rates in the other seating positions (9.4-11.2%). Sitting on the HEMS crew member rear seat also was associated with the highest percentage of severe and minor injuries (12.5% each). In HEMS accidents, the patients' position and the HEMS crew member rear seat were found to be at the highest risk for fatal or severe injuries. These results support the urgent requirement of a large international data base for HEMS accidents as a basis for further studies to improve the safety in HEMS missions. Copyright © 2013 Elsevier Ltd. All rights reserved.

77 FR 54836 - Federal Motor Vehicle Safety Standards

Science.gov (United States)

2012-09-06

... DEPARTMENT OF TRANSPORTATION National Highway Traffic Safety Administration 49 CFR Part 571 Federal Motor Vehicle Safety Standards CFR Correction 0 In Title 49 of the Code of Federal Regulations... read as follows: Sec. 571.119 Standard No. 119; New pneumatic tires for motor vehicles with a GVWR of...

75 FR 17605 - Federal Motor Vehicle Safety Standards; Roof Crush Resistance

Science.gov (United States)

2010-04-07

... that the challenge was to push to a level where the safety benefits are still reasonable in relation to... it is inequitable to those who travel in large vans and large sport utility vehicles (SUVs) for those... pickup trucks, vans and sport utility vehicles that have the capacity to seat three or more occupants...

Take your seats: Leftward asymmetry in classroom seating choice

Directory of Open Access Journals (Sweden)

Victoria Lynn Harms

2015-08-01

Full Text Available Despite an overall body symmetry, human behaviour is full of examples of asymmetry, from writing or gesturing to kissing and cradling. Prior research has revealed that theatre patrons show a bias towards sitting on the right side of a movie theatre. Two competing theories have attempted to explain this seating asymmetry: one posits that expectation of processing demand drives the bias; the other posits that basic motor asymmetries drive the bias. To test these theories we assessed the real-world classroom seating choices of university students using photographs. A bias for students to choose seats on the left side of the classroom was observed, in contrast to the right side bias observed in theatre seating studies. These results provide evidence in support of a processing-expectation bias.

Semi-active variable stiffness vibration control of vehicle seat suspension using an MR elastomer isolator

International Nuclear Information System (INIS)

Du, Haiping; Li, Weihua; Zhang, Nong

2011-01-01

This paper presents a study on continuously variable stiffness control of vehicle seat suspension using a magnetorheological elastomer (MRE) isolator. A concept design for an MRE isolator is proposed in the paper and its behavior is experimentally evaluated. An integrated seat suspension model, which includes a quarter-car suspension and a seat suspension with a driver body model, is used to design a sub-optimal H ∞ controller for an active isolator. The desired control force generated by this active isolator is then emulated by the MRE isolator through its continuously variable stiffness property when the actuating condition is met. The vibration control effect of the MRE isolator is evaluated in terms of driver body acceleration responses under both bump and random road conditions. The results show that the proposed control strategy achieves better vibration reduction performance than conventional on–off control

77 FR 65765 - Petition for Exemption From the Federal Motor Vehicle Motor Theft Prevention Standard; General...

Science.gov (United States)

2012-10-30

... the vehicle. The antenna module translates the radio frequency signal received from the key into a... DEPARTMENT OF TRANSPORTATION National Highway Traffic Safety Administration Petition for Exemption From the Federal Motor Vehicle Motor Theft Prevention Standard; General Motors Corporation AGENCY...

77 FR 25534 - Petition for Exemption From the Federal Motor Vehicle Motor Theft Prevention Standard; General...

Science.gov (United States)

2012-04-30

... response back to the vehicle. The antenna module translates the radio frequency signal received from the... DEPARTMENT OF TRANSPORTATION National Highway Traffic Safety Administration Petition for Exemption From the Federal Motor Vehicle Motor Theft Prevention Standard; General Motors Corporation AGENCY...

33 CFR 127.311 - Motor vehicles.

Science.gov (United States)

2010-07-01

...) WATERFRONT FACILITIES WATERFRONT FACILITIES HANDLING LIQUEFIED NATURAL GAS AND LIQUEFIED HAZARDOUS GAS Waterfront Facilities Handling Liquefied Natural Gas Operations § 127.311 Motor vehicles. (a) The operator... storage tank or loading flange. (b) During transfer operations, no person may— (1) Stop or park a motor...

49 CFR 583.10 - Outside suppliers of passenger motor vehicle equipment.

Science.gov (United States)

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Outside suppliers of passenger motor vehicle... CONTENT LABELING § 583.10 Outside suppliers of passenger motor vehicle equipment. (a) For each unique type of passenger motor vehicle equipment for which a manufacturer or allied supplier requests information...

National Motor Vehicle Crash Causation Survey (NMVCCS)

Data.gov (United States)

Department of Transportation — The National Motor Vehicle Crash Causation Survey (NMVVCS) was a nationwide survey of crashes involving light passenger vehicles, with a focus on the factors related...

48 CFR 970.5223-5 - DOE motor vehicle fleet fuel efficiency.

Science.gov (United States)

2010-10-01

... and Contract Clauses for Management and Operating Contracts 970.5223-5 DOE motor vehicle fleet fuel..., insert the following clause in contracts providing for Contractor management of the motor vehicle fleet... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false DOE motor vehicle fleet...

49 CFR 565.14 - Motor vehicles imported into the United States.

Science.gov (United States)

2010-10-01

... 49 Transportation 6 2010-10-01 2010-10-01 false Motor vehicles imported into the United States...) REQUIREMENTS VIN Requirements § 565.14 Motor vehicles imported into the United States. (a) Importers shall utilize the VIN assigned by the original manufacturer of the motor vehicle. (b) All passenger cars...

36 CFR 13.1316 - Commercial transport of passengers by motor vehicles.

Science.gov (United States)

2010-07-01

... passengers by motor vehicles. 13.1316 Section 13.1316 Parks, Forests, and Public Property NATIONAL PARK... National Park General Provisions § 13.1316 Commercial transport of passengers by motor vehicles. Commercial transport of passengers by motor vehicles on Exit Glacier Road is allowed without a written permit. However...

49 CFR 583.11 - Allied suppliers of passenger motor vehicle equipment.

Science.gov (United States)

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Allied suppliers of passenger motor vehicle... CONTENT LABELING § 583.11 Allied suppliers of passenger motor vehicle equipment. (a) For each unique type of passenger motor vehicle equipment which an allied supplier supplies to the manufacturer with which...

77 FR 29752 - Petition for Exemption From the Federal Motor Vehicle Motor Theft Prevention Standard; Jaguar...

Science.gov (United States)

2012-05-18

... From the Federal Motor Vehicle Motor Theft Prevention Standard; Jaguar Land Rover AGENCY: National... part 543, Exemption from the Theft Prevention Standard. This petition is granted, because the agency... be as effective in reducing and deterring motor vehicle theft as compliance with the parts-marking...

76 FR 12220 - Petition for Exemption From the Federal Motor Vehicle Motor Theft Prevention Standard; Jaguar...

Science.gov (United States)

2011-03-04

... From the Federal Motor Vehicle Motor Theft Prevention Standard; Jaguar Land Rover AGENCY: National... 543, Exemption from the Theft Prevention Standard. This petition is granted because the agency has... effective in reducing and deterring motor vehicle theft as compliance with the parts-marking requirements of...

40 CFR 85.1506 - Inspection and testing of imported motor vehicles and engines.

Science.gov (United States)

2010-07-01

... motor vehicles and engines. 85.1506 Section 85.1506 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Importation of Motor Vehicles and Motor Vehicle Engines § 85.1506 Inspection and testing of imported motor vehicles and...

78 FR 20881 - Control of Air Pollution From Motor Vehicles: Tier 3 Motor Vehicle Emission and Fuel Standards...

Science.gov (United States)

2013-04-08

...The EPA is announcing two public hearings to be held for the proposed rule ``Control of Air Pollution from Motor Vehicles: Tier 3 Motor Vehicle Emission and Fuel Standards'' (the proposed rule is hereinafter referred to as ``Tier 3''), which will be published separately in the Federal Register. The hearings will be held in Philadelphia, PA on April 24, 2013 and in Chicago, IL on April 29, 2013. The comment period for the proposed rulemaking will end on June 13, 2013.

49 CFR 173.33 - Hazardous materials in cargo tank motor vehicles.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Hazardous materials in cargo tank motor vehicles... Transportation § 173.33 Hazardous materials in cargo tank motor vehicles. (a) General requirements. (1) No person may offer or accept a hazardous material for transportation in a cargo tank motor vehicle except as...

76 FR 55825 - Federal Motor Vehicle Safety Standards, Child Restraint Systems

Science.gov (United States)

2011-09-09

... [Docket No. NHTSA-2011-0139] RIN 2127-AJ44 Federal Motor Vehicle Safety Standards, Child Restraint Systems..., amends a provision in Federal Motor Vehicle Safety Standard No. 213, ``Child restraint systems,'' that... provision: When a motor vehicle safety standard is in effect under this chapter, a State or a political...

In-situ Study of Seating Static Comfort in Passenger Vehicles

Directory of Open Access Journals (Sweden)

Seraj Umi Salmah

2018-01-01

Full Text Available In today’s automotive market, comfort is huge selling point of a vehicle. Priority is given by buyers to how comfortable a seat feels during purchase decisions. The measure of comfort is harmonious mix of many aspects such as human ergonomics and physiological factors. However, a gap still exists between objective and subjective measures due to lack of emphasis by past researchers. This is particularly obvious in the lumbar support feature that has still not been able to address the health problems related to driving. This project focuses on bridging the gap by giving users the ability to define true preferred posture in realistic settings. This is done by the creation of a apparatus that allows users to individually manipulate the seat contour for optimum support in more segments than just lumbar area. The experiment is performed in 3 parts, where in each part different segments of the apparatus are manipulatable (lumbar segment, sacral & thoracic segment, and all segments. Sixty human subjects’ statistics are recorded (gender, age, BMI and height and the subjects are palpated to locate internal joints. These joints are marked and postural angles between them are measured using a goniometer. In each seat configuration, the angles are measured and a comfort rating is taken to be compared. It was found that the posture angles are different among the 3 experiments, and there is a change in comfort felt. Some human factors have also been proven to contribute heavily to angles chosen by occupants.

49 CFR 565.24 - Motor vehicles imported into the United States.

Science.gov (United States)

2010-10-01

... 49 Transportation 6 2010-10-01 2010-10-01 false Motor vehicles imported into the United States...) REQUIREMENTS Alternative VIN Requirements In Effect for Limited Period § 565.24 Motor vehicles imported into... motor vehicle. (b) A passenger car certified by a Registered Importer under 49 CFR part 592 shall have a...

26 CFR 41.4482(a)-1 - Definition of highway motor vehicle.

Science.gov (United States)

2010-04-01

... of its own motor, whether such motor is powered by gasoline, diesel fuel, special motor fuels... 26 Internal Revenue 16 2010-04-01 2010-04-01 true Definition of highway motor vehicle. 41.4482(a... (CONTINUED) MISCELLANEOUS EXCISE TAXES EXCISE TAX ON USE OF CERTAIN HIGHWAY MOTOR VEHICLES Tax on Use of...

76 FR 76622 - Federal Management Regulation; Motor Vehicle Management

Science.gov (United States)

2011-12-08

...; Docket 2011-0011; Sequence 2] RIN 3090-AJ14 Federal Management Regulation; Motor Vehicle Management... Administration is amending the Federal Management Regulation (FMR) by revising current policy on the definitions... CONTACT: For clarification of content, contact Mr. James Vogelsinger, Director, Motor Vehicle Management...

Roadside observation of child passenger restraint use

Directory of Open Access Journals (Sweden)

Beth Bruce

2015-10-01

Full Text Available Background: Despite legislation and research evidence supporting the use of childhood vehicle restraints, motor vehicle crashes remain the leading cause of injury, death and disability among Canadian children. Methods: Working in collaboration with trained car seat specialists and police officers, roadside checks were conducted to observe correct use of child restraints. Results: Of the 1323 child vehicle restraints inspected, 99.6% of the children were restrained, 91% were in the correct seat, and 48% of restraints were correctly installed. The seat/restraint types most used incorrectly used were booster seats (31% and seat belts (53%. The majority of incorrectly installed or fitted seats (55% were forward facing. Common errors in installation and fit included the seat not being secured tightly enough to the vehicle, incorrect tether strap use, the harness not being tight enough, and/or the chest clip being in the wrong place. Conclusions: The greatest proportion of incorrect seat use was among those children who transitioned to a seat belt too soon. The greatest proportion of installation and fit errors were among forward facing seats. Researchers recommend: 1 targeting parents with older children (ages 3 and above regarding transitioning too soon from forward facing seats to booster seats, and from booster seats to seat belts; 2 targeting parents with younger children regarding correct installation of rear facing and forward facing seats; 3 collaborating with police officers to review the most common errors and encourage observation at roadside checks; and 4 creating community awareness by way of roadside checks.

How motor vehicles contribute to global warming and air pollution

International Nuclear Information System (INIS)

Anon.

1990-01-01

In this chapter, the authors describe ways in which motor vehicles are contributing to global climate change and health problems caused by air pollution. Globally, motor vehicles account for about a third of world oil consumption and about 14% of the world's carbon dioxide emissions from fossil fuel burning. For the US the figures are 50% of oil demand and about 25% of carbon dioxide emissions. Motor vehicles are the major source of ozone precursors and monitoring data suggest that ozone concentrations are increasing by about one percent per year in the northern hemisphere and are causing adverse effects on human health and on crops. A major source of chlorofluorocarbons in the atmosphere is motor vehicle air conditioning. Annually about 120,000 metric tons of CFCs are used in new vehicles and in serving air conditioners in older vehicles. According to the EPA, vehicle air conditioners accounted for about 16% of the total CFC use in the US during 1989. According to the Montreal Protocol, CFCs are to be completely phased out of new vehicles by the turn of the century, thus reducing the depletion of the stratospheric ozone layer

Dual motor drive vehicle speed synchronization and coordination control strategy

Science.gov (United States)

Huang, Hao; Tu, Qunzhang; Jiang, Chenming; Ma, Limin; Li, Pei; Zhang, Hongxing

2018-04-01

Multi-motor driven systems are more and more widely used in the field of electric engineering vehicles, as a result of the road conditions and the variable load of engineering vehicles, makes multi-motors synchronization coordinated control system as a key point of the development of the electric vehicle drive system. This paper based on electrical machinery transmission speed in the process of engineering vehicles headed for coordinated control problem, summarized control strategies at home and abroad in recent years, made analysis and comparison of the characteristics, finally discussed the trend of development of the multi-motor coordination control, provided a reference for synchronized control system research of electric drive engineering vehicles.

41 CFR 109-38.204-4 - Report of exempted motor vehicles.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Report of exempted motor..., TRANSPORTATION, AND MOTOR VEHICLES 38-MOTOR EQUIPMENT MANAGEMENT 38.2-Registration, Identification, and Exemptions § 109-38.204-4 Report of exempted motor vehicles. DOE offices shall provide upon request the...

Preventing passenger vehicle occupant injuries by vehicle design--a historical perspective from IIHS.

Science.gov (United States)

O'Neill, Brian

2009-04-01

and chest injury measures recorded on driver and front-seat test dummies. NHTSA later added side crash tests and rollover ratings to the U.S. NCAP. Consumer crash testing spread worldwide in the 1990s. In 1995, the Insurance Institute for Highway Safety (IIHS) began using frontal offset crash tests to rate and compare frontal crashworthiness and later added side and rear crash assessments. Shortly after, Europe launched EuroNCAP to assesses new car performance including front, side, and front-end pedestrian tests. The influence of these consumer-oriented crash test programs on vehicle designs has been major. From the beginning, U.S. NCAP results prompted manufacturers to improve seat belt performance. Frontal offset tests from IIHS and EuroNCAP resulted in greatly improved front-end crumple zones and occupant compartments. Side impact tests have similarly resulted in improved side structures and accelerated the introduction of side impact airbags, especially those designed to protect occupant's heads. Vehicle safety designs, initially driven by regulations and later by consumer demand because of crash testing, have proven to be very successful public health measures. Since they were first introduced in the late 1960s, vehicle safety designs have saved hundreds of thousands of lives and prevented countless injuries worldwide. The designs that improved vehicle crashworthiness have been particularly effective. Some newer crash avoidance designs also have the potential to be effective-e.g., electronic stability control is already saving many lives in single-vehicle crashes. However, determining the actual effectiveness of these new technologies is a slow process and needs real-world crash experience because there are no assessment equivalent of crash tests for crash avoidance designs.

76 FR 24402 - Federal Motor Vehicle Theft Prevention Standard

Science.gov (United States)

2011-05-02

... [Docket No. NHTSA-2009-0069] RIN 2127-AK81 Federal Motor Vehicle Theft Prevention Standard AGENCY... address for submission, and the procedure to submit designation of target areas on high theft major parts... the Theft Prevention Standard, manufacturers of high theft passenger motor vehicle lines subject to...

49 CFR 383.91 - Commercial motor vehicle groups.

Science.gov (United States)

2010-10-01

... 49 Transportation 5 2010-10-01 2010-10-01 false Commercial motor vehicle groups. 383.91 Section 383.91 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL MOTOR CARRIER SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION FEDERAL MOTOR CARRIER SAFETY REGULATIONS COMMERCIAL...

Assessing population exposures to motor vehicle exhaust.

Science.gov (United States)

Van Atten, Chris; Brauer, Michael; Funk, Tami; Gilbert, Nicolas L; Graham, Lisa; Kaden, Debra; Miller, Paul J; Bracho, Leonora Rojas; Wheeler, Amanda; White, Ronald H

2005-01-01

The need is growing for a better assessment of population exposures to motor vehicle exhaust in proximity to major roads and highways. This need is driven in part by emerging scientific evidence of adverse health effects from such exposures and policy requirements for a more targeted assessment of localized public health impacts related to road expansions and increasing commercial transportation. The momentum for improved methods in measuring local exposures is also growing in the scientific community, as well as for discerning which constituents of the vehicle exhaust mixture may exert greater public health risks for those who are exposed to a disproportionate share of roadway pollution. To help elucidate the current state-of-the-science in exposure assessments along major roadways and to help inform decision makers of research needs and trends, we provide an overview of the emerging policy requirements, along with a conceptual framework for assessing exposure to motor-vehicle exhaust that can help inform policy decisions. The framework includes the pathway from the emission of a single vehicle, traffic emissions from multiple vehicles, atmospheric transformation of emissions and interaction with topographic and meteorologic features, and contact with humans resulting in exposure that can result in adverse health impacts. We describe the individual elements within the conceptual framework for exposure assessment and discuss the strengths and weaknesses of various approaches that have been used to assess public exposures to motor vehicle exhaust.

CDC Vital Signs: Motor Vehicle Crash Injuries: Costly but Preventable

Science.gov (United States)

... Press Kit Read the MMWR Science Clips Motor Vehicle Crash Injuries Costly but Preventable Language: English (US) ... and how to prevent future crashes. Problem Motor vehicle crashes are a leading cause of injury in ...

50 CFR 35.5 - Commercial enterprises, roads, motor vehicles, motorized equipment, motorboats, aircraft...

Science.gov (United States)

2010-10-01

... 50 Wildlife and Fisheries 6 2010-10-01 2010-10-01 false Commercial enterprises, roads, motor... Rules § 35.5 Commercial enterprises, roads, motor vehicles, motorized equipment, motorboats, aircraft... private rights, there shall be no commercial enterprise and no permanent road within a wilderness unit...

Frequency, causes and human impact of motor vehicle-related road traffic accident (RTA) in Lubumbashi, Democratic Republic of Congo.

Science.gov (United States)

Nangana, Luzitu Severin; Monga, Ben; Ngatu, Nlandu Roger; Mbelambela, Etongola Papy; Mbutshu, Lukuke Hendrick; Malonga, Kaj Francoise

2016-09-01

Road traffic accident (RTA)-related trauma remains a public health issue. The aim of this study was to determine the frequency, causes and human impact of motor vehicle-related RTA in Lubumbashi, Democratic Republic of Congo. A prospective cross-sectional study was conducted in the first semester of the year 2015 in which 288 drivers (144 RTA-causing drivers and 144 control drivers who have been declared not guilty by road safety agents) involved in 144 motor vehicle-related RTA were interviewed, and only data on all RTA involving two motor vehicles with at least four wheels were recorded and analyzed. Results showed a total of 144 RTA that involved two motor vehicles with four wheels occurring during the study period which affected 104 people, including 93 injury and 11 fatality cases. The mean age of RTA-causing drivers was 33.8 ± 7.4, whereas it was 35 ± 8.8 for control drivers. The majority of RTA-causing drivers (53.4 %) did not attend a driving school. Over speeding (32 %), distracted driving (22 %), overtaking (16 %) and careless driving/risky maneuver (15 %) and driving under the influence of alcohol (9 %) were the main causes of RTA occurrence. In addition, the absence of a valid driving license [aOR = 12.74 (±2.71); 95 % CI 3.877-41.916; p = 0.015], unfastened seat belt for the RTA-causing driver [aOR = 1.85 (±0.62); 95 % CI 1.306-6.661; p = 0.048] and presence of damages on RTA-causing vehicle [aOR = 33.56 (24.01); 95 % CI 1.429-78.352; p = 0.029] were associated with the occurrence of RTA-related fatality. This study showed a relatively high frequency of RTA occurring in Lubumbashi and suggests the necessity to reinforce road traffic regulation.

Does a tow-bar increase the risk of neck injury in rear-end collisions?

Science.gov (United States)

Olesen, Anne Vingaard; Elvik, Rune; Andersen, Camilla Sloth; Lahrmann, Harry S

2018-06-01

Does a tow-bar increase the risk of neck injury in the struck car in a rear-end collision? The rear part of a modern car has collision zones that are rendered nonoperational when the car is equipped with a tow-bar. Past crash tests have shown that a car's acceleration was higher in a car equipped with a tow-bar and also that a dummy placed in a car with a tow-bar had higher peak acceleration in the lower neck area. This study aimed to investigate the association between the risk of neck injury in drivers and passengers, and the presence of a registered tow-bar on the struck car in a rear-end collision. We performed a merger of police reports, the National Hospital Discharge Registry, and the National Registry of Motor Vehicles in Denmark. We identified 9,370 drivers and passengers of whom 1,519 were diagnosed with neck injury within the first year after the collision. We found a statistically insignificant 5% decrease in the risk of neck injury in the occupants of the struck car when a tow-bar was fitted compared to when it was not fitted (hazard ratio=0.95; 95% confidence level=0.85-1.05; p=0.32). The result was controlled for gender, age, and the seat of the occupant. Several other collision and car characteristics and demographic information on the drivers and passengers were evaluated as confounders but were not statistically significant. The present study may serve as valuable input for a meta-analysis on the effect of a tow-bar because negative results are necessary in order to avoid publication bias. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

40 CFR 80.531 - How are motor vehicle diesel fuel credits generated?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false How are motor vehicle diesel fuel... (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel... are motor vehicle diesel fuel credits generated? (a) Generation of credits from June 1, 2006 through...

The speed of change : motor vehicles and people in Africa, 1890-2000

NARCIS (Netherlands)

Gewald, J.B.; Luning, Sabine; Walraven, van K.

2009-01-01

In the early 1900s the motor-vehicle (car, bus, lorry or motorcycle) was introduced in sub-Saharan Africa. Initially the plaything and symbol of colonial domination, the motor-vehicle transformed the economic and social life of the continent. Indeed, the motor-vehicle is arguably the single most

Evaluating the impact of child safety seat check-up events on parental knowledge.

Science.gov (United States)

Herring, Ashley B; Jones, Ches; Nunez, Casandra

2002-12-01

Riding unrestrained is the greatest risk factor for death and injury among children in motor vehicles. Restraining a child can reduce the risk of death for that child by up to 71%. However, despite increased awareness, child safety seat usage rates are still disturbingly low. The purpose of this study was to evaluate the impact that child safety seat check-up events have on parental knowledge on child safety seats and installation. The subjects for this study were 101 parents/caregivers who attended child safety seat check-up events in northwest Arkansas from May 2000 through June 2001. A 20-item survey was conducted via the telephone. Results showed that the check-up events in northwest Arkansas have had an impact on self-efficacy. The participants of the events were primarily Caucasian and females in the 30-34 age group. Nine of 10 subjects scored in the high knowledge category. Conclusions are that check-up events do have an impact on parental knowledge and are accepted by the target group. Additionally, participants believed that car seats are of great importance and do protect their children in the event of a crash.

Improved seat and manniken models to study rear impact protection

NARCIS (Netherlands)

Kant, A.R.; Wu, P.; Shanmugavelu, I.; Mondeau, S.R.

1998-01-01

Occupant injury in automobile rear-end collisions is rapidly becoming one of the most aggravating traffic safety problems with high human suffering and societal costs. Recent studies in Europe, Canada and Japan have found that injury claims, in particular neck injuries due to rear impact have

Public opinion on motor vehicle-related injury prevention policies: a systematic review of a decade of research.

Science.gov (United States)

Debinski, Beata; Clegg Smith, Katherine; Gielen, Andrea

2014-01-01

Legislation is an effective strategy for reducing road-related fatalities and injuries. Public opinion can be an impetus for passing new laws and can affect the success of their implementation, but little is known about the current state of public opinion toward existing and proposed road-related policies in the United States. This review describes the scope and results of research on public support for state- and local-level evidence-based motor vehicle- and bicycle-related policies. We identify gaps in our understanding of public support for these policies. Published U.S. literature and all reports from the NHTSA from the past decade (2003-2012) were searched for data on opinions about existing or proposed policies related to motor vehicle or bicycle injury prevention. Twenty-six studies fulfilled the inclusion criteria. In all, studies reported public opinion about 7 injury prevention topic areas: all-terrain vehicles (n = 1), automated enforcement with red light and speed cameras (n = 5), distracted driving (n = 4), drinking and driving (n = 5), graduated driver licensing (n = 7), helmets (n = 7), and seat belts (n = 4). Twenty-three studies focused only on one topic, and 3 sought public opinion about multiple topic areas. The studies revealed generally high levels of support for injury prevention policies in all topic areas. Fifteen studies collected information from national samples, and only 7 studies reported data from the state (n = 5) or local (n = 2) level. There is a relatively small evidence base on public opinion related to motor vehicle- and bicycle-related evidence-based policies; even less is less known for state- or county-specific policies. The findings of this review suggest that the public's opinion toward injury prevention legislation is generally favorable. This information can be used to communicate with the media and policy makers to reinforce the need for effective policy solutions to continuing motor vehicle injury problems. More research

The RID2 biofidelic rear impact dummy: a pilot study using human subjects in low speed rear impact full scale crash tests.

Science.gov (United States)

Croft, Arthur C; Philippens, Mathieu M G M

2007-03-01

Human subjects and the recently developed RID2 rear impact crash test dummy were exposed to a series of full scale, vehicle-to-vehicle crash tests. To evaluate the biofidelity of the RID2 anthropometric test dummy on the basis of calculated neck injury criterion (NIC) values by comparing these values to those obtained from human subjects exposed in the very same crashes. The widely used and familiar hybrid III dummy has been said to lack biofidelity in the special application of low speed rear impact crashes. Several attempts have been made to modify this dummy with only marginal success. Two completely new dummies have been developed; the BioRID and the RID2. Neither have been tested under real world crash boundary conditions in side-by-side comparisons with live human subjects. Volunteer subjects, including a 50th percentile male, a 95th percentile male, and a 50th percentile female, were placed in the driver's seat of a vehicle and subjected to a series of three low speed rear impact crashes each. The RID2 dummy, which is modeled after a 50th percentile male, was placed in the passenger seat in each case. Both subjects and dummy were fully instrumented and acceleration-time histories were recorded. From this data, velocities of the heads and torsos were determined and both were used to calculate the NIC values for both crash test subjects and the RID2. The RID2 demonstrated generally higher head accelerations and NIC values than those of the human subjects. Most of the observed variations might be explained on the basis of differing head restraint geometry, posture, and body size. The RID2 NIC values compared most favorably with those of the 50th percentile male subject. For the whole group, the correlations between RID2 and human subjects did not reach statistical significance. The small number of test subjects and crash tests limited the statistical power of this pilot study, and the correlation between the RID2 and human subject NIC values were not

41 CFR 102-34.230 - How am I responsible for protecting Government motor vehicles?

Science.gov (United States)

2010-07-01

... theft or damage; and (b) Lock the unattended Government motor vehicle. (The only exception to this... protecting Government motor vehicles? 102-34.230 Section 102-34.230 Public Contracts and Property Management... 34-MOTOR VEHICLE MANAGEMENT Official Use of Government Motor Vehicles § 102-34.230 How am I...

Modeling Hot Spot Motor Vehicle Theft Crime in Relation to Landuse and Settlement Patterns

Directory of Open Access Journals (Sweden)

Djaka Marwasta

2004-01-01

Full Text Available The crowd of Yogyakarta urban has impacted its surrounding area, including Depok sub district, which is indicated by the rising of physical development, for example education facilities and settlements. The progress does not only bring positive impact, but also negative impact for instance the rising of crime number i.e. motor vehicle robbery. The aims of this research are 1 mapping motor vehicle robbery data as the distribution map and identifying motor vehicle robbery hot spot base on distrbution map; and 2 studying the correlation of motor vehicle robbery hot spot with physical environment phenomena, i.e. land use type and settlement pattern. The research method consists of two parts; they are motor vehicle robbery cluster analysis and the relation of motor vehicle robbery and physical environment analysis. Motor vehicle robbery cluster analysis is using distribution data, which analyzes the distribution into motor vehicle robbery hot spot with nearest neighbor tehnique. Contingency coefficient and frequency distribution analysis is used to analyze the correlation of motor vehicle robbery hot spot and physical environment. Contingency coefficient is used to study the relation of motor vehicle robbery hot spot polygon with physical environment condition, whereas frequency distribution is used to study the distribution of motor vehicle robbery in the hot spot with physical environment condition. Physical environment which consists of land use type, housing density, house regularity pattern, and the average of building size, are obtained from interpretation of black and white panchromatic aerial photograph year 2000, in the scale 1 : 20.000. the most motor vehicle robbery hot spot is found on the settlement area, 68,3% from 378 motor vehicle robbery cases in the hot spot. The seond level is found on the education area (16.4%. The most motor vehicle hot spot in the settlement is found on the hight density and irregular settlement, which have big

78 FR 77790 - Petition for Exemption From the Federal Motor Vehicle Theft Prevention Standard; General Motors...

Science.gov (United States)

2013-12-24

... vehicle. The antenna module translates the radio frequency signal received from the key into a digital... DEPARTMENT OF TRANSPORTATION National Highway Traffic Safety Administration Petition for Exemption From the Federal Motor Vehicle Theft Prevention Standard; General Motors Corporation AGENCY: National...

Self-regulation of motor vehicle advertising: is it working in Australia?

Science.gov (United States)

Donovan, Robert J; Fielder, Lynda J; Ouschan, Robyn; Ewing, Michael

2011-05-01

There is growing concern that certain content within motor vehicle advertising may have a negative influence on driving attitudes and behaviours of viewers, particularly young people, and hence a negative impact on road safety. In response, many developed countries have adopted a self-regulatory approach to motor vehicle advertising. However, it appears that many motor vehicle advertisements in Australia and elsewhere are not compliant with self-regulatory codes. Using standard commercial advertising methods, we exposed three motor vehicle ads that had been the subject of complaints to the Australian Advertising Standards Board (ASB) to, N = 463, 14-55 year olds to assess the extent to which their perceptions of the content of the ads communicated themes that were contrary to the Australian self-regulatory code. All three ads were found to communicate messages contrary to the code (such as the vehicle's speed and acceleration capabilities). However, the ASB had upheld complaints about only one of the ads. Where motor vehicle advertising regulatory frameworks exist to guide motor vehicle advertisers as to what is and what is not acceptable in their advertising, greater efforts are needed to ensure compliance with these codes. One way may be to make it mandatory for advertisers to report consumer pre-testing of their advertising to ensure that undesirable messages are not being communicated to viewers. Copyright © 2010 Elsevier Ltd. All rights reserved.

Economic costs of motor vehicle emissions in China: a case study

International Nuclear Information System (INIS)

Xin Deng

2006-01-01

The last decade has witnessed a dramatic increase in the number of motor vehicles in China. Motor vehicles have become an increasingly important contributor to air pollution in major Chinese cities. While research interest in vehicular pollution in China has increased in recent years, there is little research on evaluating monetary costs of this pollution. This paper uses Beijing as a case study to evaluate the magnitudes of air pollution concerning motor vehicles. A monetary estimation of air pollution in regard to motor vehicles is presented on the basis of data for Beijing in 2000. Two methods - willingness-to-pay and human capital methods - are used to analyse the high and low points of estimation. (author)

75 FR 66686 - Federal Motor Vehicle Safety Standards; Seat Belt Assembly Anchorages, School Bus Passenger...

Science.gov (United States)

2010-10-29

... loose belts) also applies to seats that have wheelchair positions or side emergency doors behind them... have wheelchair positions or side emergency doors behind them); and, the test requirements for self... which correspond to the size of some high school football players) and school buses closer in weight to...

41 CFR 101-25.110-3 - Tires accompanying new motor vehicles.

Science.gov (United States)

2010-07-01

... motor vehicles. 101-25.110-3 Section 101-25.110-3 Public Contracts and Property Management Federal...-GENERAL 25.1-General Policies § 101-25.110-3 Tires accompanying new motor vehicles. The tire identifications and recordkeeping regulations issued by the Department of Transportation require each motor...

Development and validation of a modified Hybrid-III six-year-old dummy model for simulating submarining in motor-vehicle crashes.

Science.gov (United States)

Hu, Jingwen; Klinich, Kathleen D; Reed, Matthew P; Kokkolaras, Michael; Rupp, Jonathan D

2012-06-01

In motor-vehicle crashes, young school-aged children restrained by vehicle seat belt systems often suffer from abdominal injuries due to submarining. However, the current anthropomorphic test device, so-called "crash dummy", is not adequate for proper simulation of submarining. In this study, a modified Hybrid-III six-year-old dummy model capable of simulating and predicting submarining was developed using MADYMO (TNO Automotive Safety Solutions). The model incorporated improved pelvis and abdomen geometry and properties previously tested in a modified physical dummy. The model was calibrated and validated against four sled tests under two test conditions with and without submarining using a multi-objective optimization method. A sensitivity analysis using this validated child dummy model showed that dummy knee excursion, torso rotation angle, and the difference between head and knee excursions were good predictors for submarining status. It was also shown that restraint system design variables, such as lap belt angle, D-ring height, and seat coefficient of friction (COF), may have opposite effects on head and abdomen injury risks; therefore child dummies and dummy models capable of simulating submarining are crucial for future restraint system design optimization for young school-aged children. Copyright © 2011 IPEM. Published by Elsevier Ltd. All rights reserved.

Life-threatening motor vehicle crashes in bright sunlight

OpenAIRE

Redelmeier, Donald A.; Raza, Sheharyar

2017-01-01

Abstract Bright sunlight may create visual illusions that lead to driver error, including fallible distance judgment from aerial perspective. We tested whether the risk of a life-threatening motor vehicle crash was increased when driving in bright sunlight. This longitudinal, case-only, paired-comparison analysis evaluated patients hospitalized because of a motor vehicle crash between January 1, 1995 and December 31, 2014. The relative risk of a crash associated with bright sunlight was estim...

14 CFR 1204.1600 - Issuance of motor vehicle for home-to-work.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 5 2010-01-01 2010-01-01 false Issuance of motor vehicle for home-to-work... ADMINISTRATIVE AUTHORITY AND POLICY Temporary Duty Travel-Issuance of Motor Vehicle for Home-to-Work Transportation § 1204.1600 Issuance of motor vehicle for home-to-work. When a NASA employee on temporary duty...

Research on motor braking-based DYC strategy for distributed electric vehicle

Science.gov (United States)

Zhang, Jingming; Liao, Weijie; Chen, Lei; Cui, Shumei

2017-08-01

In order to bring into full play the advantages of motor braking and enhance the handling stability of distributed electric vehicle, a motor braking-based direct yaw moment control (DYC) strategy was proposed. This strategy could identify whether a vehicle has under-steered or overs-steered, to calculate the direct yaw moment required for vehicle steering correction by taking the corrected yaw velocity deviation and slip-angle deviation as control variables, and exert motor braking moment on the target wheels to perform correction in the manner of differential braking. For validation of the results, a combined simulation platform was set up finally to simulate the motor braking control strategy proposed. As shown by the results, the motor braking-based DYC strategy timely adjusted the motor braking moment and hydraulic braking moment on the target wheels, and corrected the steering deviation and sideslip of the vehicle in unstable state, improving the handling stability.

75 FR 15620 - Federal Motor Vehicle Safety Standards; Air Brake Systems

Science.gov (United States)

2010-03-30

... fully develop improved brake systems and also to ensure vehicle control and stability while braking... [Docket No. NHTSA 2009-0175] RIN 2127-AK62 Federal Motor Vehicle Safety Standards; Air Brake Systems... Federal motor vehicle safety standard for air brake systems by requiring substantial improvements in...

78 FR 9623 - Federal Motor Vehicle Safety Standards; Air Brake Systems

Science.gov (United States)

2013-02-11

... initial speeds, vehicle manufacturers will need to develop unique or complicated braking systems to comply... [Docket No. NHTSA-2013-0011] RIN 2127-AL11 Federal Motor Vehicle Safety Standards; Air Brake Systems... rule that amended the Federal motor vehicle safety standard for air brake systems by requiring...

76 FR 44829 - Federal Motor Vehicle Safety Standards; Air Brake Systems

Science.gov (United States)

2011-07-27

... [Docket No. NHTSA-2009-0175] RIN 2127-AK84 Federal Motor Vehicle Safety Standards; Air Brake Systems... final rule that amended the Federal motor vehicle safety standard for air brake systems by requiring... between Bendix Commercial Vehicle Systems and Dana Corporation; and ArvinMeritor. The agency received four...

Compulsive Cell Phone Use and History of Motor Vehicle Crash

Science.gov (United States)

O’Connor, Stephen S.; Whitehill, Jennifer M.; King, Kevin M.; Kernic, Mary A.; Boyle, Linda Ng; Bresnahan, Brian; Mack, Christopher D.; Ebel, Beth E.

2013-01-01

Introduction Few studies have examined the psychological factors underlying the association between cell phone use and motor vehicle crash. We sought to examine the factor structure and convergent validity of a measure of problematic cell phone use and explore whether compulsive cell phone use is associated with a history of motor vehicle crash. Methods We recruited a sample of 383 undergraduate college students to complete an on-line assessment that included cell phone use and driving history. We explored the dimensionality of the Cell Phone Overuse Scale (CPOS) using factor analytic methods. Ordinary least squares regression models were used to examine associations between identified subscales and measures of impulsivity, alcohol use, and anxious relationship style to establish convergent validity. We used negative binomial regression models to investigate associations between the CPOS and motor vehicle crash incidence. Results We found the CPOS to be comprised of four subscales: anticipation, activity interfering, emotional reaction, and problem recognition. Each displayed significant associations with aspects of impulsivity, problematic alcohol use, and anxious relationship style characteristics. Only the anticipation subscale demonstrated statistically significant associations with reported motor vehicle crash incidence, controlling for clinical and demographic characteristics (RR 1.13, CI 1.01 to 1.26). For each one-point increase on the 6-point anticipation subscale, risk for previous motor vehicle crash increased by 13%. Conclusions Crash risk is strongly associated with heightened anticipation about incoming phone calls or messages. The mean score on the CPOS is associated with increased risk of motor vehicle crash but does not reach statistical significance. PMID:23910571

The Effects of Microgravity on Seated Height (Spinal Elongation)

Science.gov (United States)

Young, K. S.; Rajulu, S.

2011-01-01

ABSTRACT Many physiological factors, such as spinal elongation, fluid shifts, bone atrophy, and muscle loss, occur during an exposure to a microgravity environment. Spinal elongation is just one of the factors that can also affect the safety and performance of a crewmember while in space. Spinal elongation occurs due to the lack of gravity/compression on the spinal column. This allows for the straightening of the natural spinal curve. There is a possible fluid shift in the inter-vertebral disks that may also result in changes in height. This study aims at collecting the overall change in seated height for crewmembers exposed to a microgravity environment. During previous Programs, Apollo-Soyuz Test Project (ASTP) and Skylab, spinal elongation data was collected from a small number of subjects in a standing posture but were limited in scope. Data from these studies indicated a quick increase in stature during the first few days of weightlessness, after which stature growth reached a plateau resulting in up to a 3% increase of the original measurement [1-5]. However, this data was collected only for crewmembers in standing posture and not in a seated posture. Seated height may have a different effect than standing height due to a change in posture as well as due to a compounded effect of wearing restraints and a potential compression of the gluteal area. Seated height was deemed as a critical measurement in the design of the Constellation Program s (CxP) Crew Exploration Vehicle (CEV), called Orion which is now the point-of-departure vehicle for the Multi-Purpose Crew Vehicle (MPCV) Program; therefore a better understanding of the effects of microgravity on seated height is necessary. Potential changes in seated height that may not have impacted crew accommodation in previous Programs will have significant effects on crew accommodation due to the layout of seats in the Orion.. The current and existing configuration is such that the four crewmembers are stacked two by

78 FR 42153 - Decision That Certain Nonconforming Motor Vehicles Are Eligible for Importation

Science.gov (United States)

2013-07-15

...- 2012-0162), the Ford Motor Company stated in pertinent part: Vehicles that are designed and...-0074] Decision That Certain Nonconforming Motor Vehicles Are Eligible for Importation AGENCY: National... decisions by NHTSA that certain motor vehicles not originally manufactured to comply with all applicable...

Global time trends in PAH emissions from motor vehicles

Science.gov (United States)

Shen, Huizhong; Tao, Shu; Wang, Rong; Wang, Bin; Shen, Guofeng; Li, Wei; Su, Shenshen; Huang, Ye; Wang, Xilong; Liu, Wenxin; Li, Bengang; Sun, Kang

2011-04-01

Emission from motor vehicles is the most important source of polycyclic aromatic hydrocarbons (PAHs) in urban areas. Emission factors of individual PAHs for motor vehicles reported in the literature varied 4 to 5 orders of magnitude, leading to high uncertainty in emission inventory. In this study, key factors affecting emission factors of PAHs (EF PAH) for motor vehicles were evaluated quantitatively based on thousands of EF PAH measured in 16 countries for over 50 years. The result was used to develop a global emission inventory of PAHs from motor vehicles. It was found that country and vehicle model year are the most important factors affecting EF PAH, which can be quantified using a monovariate regression model with per capita gross domestic production (purchasing power parity) as a sole independent variable. On average, 29% of variation in log-transformed EF PAH could be explained by the model, which was equivalent to 90% reduction in overall uncertainty on arithmetic scale. The model was used to predict EF PAH and subsequently PAH emissions from motor vehicles for various countries in the world during a period from 1971 to 2030. It was estimated that the global emission reached its peak value of approximate 101 Gg in 1978 and decreased afterwards due to emission control in developed countries. The annual emission picked up again since 1990 owing to accelerated energy consumption in China and other developing countries. With more and more rigid control measures taken in the developing world, global emission of PAHs is currently passing its second peak. It was predicted that the emission would decrease from 77 Gg in 2010 to 42 Gg in 2030.

49 CFR 177.823 - Movement of motor vehicles in emergency situations.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Movement of motor vehicles in emergency situations... CARRIAGE BY PUBLIC HIGHWAY General Information and Regulations § 177.823 Movement of motor vehicles in... government; (2) The carrier has permission from the Department; or (3) Movement of the transport vehicle is...

78 FR 4193 - Petition for Exemption From the Federal Motor Vehicle Motor Theft Prevention Standard; Volvo

Science.gov (United States)

2013-01-18

... DEPARTMENT OF TRANSPORTATION National Highway Traffic Safety Administration Petition for Exemption From the Federal Motor Vehicle Motor Theft Prevention Standard; Volvo AGENCY: National Highway Traffic... transponder is not identified, the CEM will not send an approved key signal to the IAU and the vehicle will be...

Electronically commutated motors for vehicle applications

Science.gov (United States)

Echolds, E. F.

1980-02-01

Two permanent magnet electronically commutated motors for electric vehicle traction are discussed. One, based on existing technology, produces 23 kW (peak) at 26,000 rpm, and 11 kW continuous at 18,000 rpm. The motor has a conventional design: a four-pole permanent magnet rotor and a three-phase stator similar to those used on ordinary induction motors. The other, advanced technology motor, is rated at 27 kW (peak) at 14,000 rpm, and 11 kW continuous at 10,500 rpm. The machine employs a permanent magnet rotor and a novel ironless stator design in an axial air gap, homopolar configuration. Comparison of the new motors with conventional brush type machines indicates potential for substantial cost savings.

Computer controlled motor vehicle battery circuit

Energy Technology Data Exchange (ETDEWEB)

Krueger, W.R.; McAuiliffe, G.N.; Schlageter, G.A.

1986-04-01

This patent consists of a motor vehicle having a DC motor, a pedal biased to a released position and depressed by the driver to increase speed. An alternate switching means affects the vehicle speed control, a foot switch is operated by the pedal and operative when the pedal is depressed to close a circuit enabling energization of the alternate switching means. A microprocessor includes a program for controlling operation of the alternate switching means, the foot switch is operative when the pedal is released to open the enabling circuit. The program includes a register which is incremented with each passage of the logic and is responsive to the incremented count in the register to instruct a change in position of the alternate switching means.

40 CFR 80.522 - May used motor oil be dispensed into diesel motor vehicles or nonroad diesel engines?

Science.gov (United States)

2010-07-01

... diesel motor vehicles or nonroad diesel engines? 80.522 Section 80.522 Protection of Environment... vehicles or nonroad diesel engines? No person may introduce used motor oil, or used motor oil blended with... later nonroad diesel engines (not including locomotive or marine diesel engines), unless both of the...

22 CFR 151.4 - Minimum limits for motor vehicle insurance.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Minimum limits for motor vehicle insurance. 151.4 Section 151.4 Foreign Relations DEPARTMENT OF STATE DIPLOMATIC PRIVILEGES AND IMMUNITIES COMPULSORY LIABILITY INSURANCE FOR DIPLOMATIC MISSIONS AND PERSONNEL § 151.4 Minimum limits for motor vehicle...

Preliminary Design of Reluctance Motors for Light Electric Vehicles Driving

Directory of Open Access Journals (Sweden)

TRIFA, V.

2009-02-01

Full Text Available The paper presents the aspects regarding FEM analysis of a reluctant motor for direct driving of the light electric vehicles. The reluctant motor take into study is of special construction suitable for direct drive of a light electric vehicle. It is an inverse radial reluctant motor, with a fixed stator mounted on front wheel shaft and an external toothed rotor fixed on the front wheel itself. A short presentation of preliminary design is continued with the FEM analysis in order to provide the optimal geometry of the motor and adequate windings.

Compulsive cell phone use and history of motor vehicle crash.

Science.gov (United States)

O'Connor, Stephen S; Whitehill, Jennifer M; King, Kevin M; Kernic, Mary A; Boyle, Linda Ng; Bresnahan, Brian W; Mack, Christopher D; Ebel, Beth E

2013-10-01

Few studies have examined the psychological factors underlying the association between cell phone use and motor vehicle crash. We sought to examine the factor structure and convergent validity of a measure of problematic cell phone use, and to explore whether compulsive cell phone use is associated with a history of motor vehicle crash. We recruited a sample of 383 undergraduate college students to complete an online assessment that included cell phone use and driving history. We explored the dimensionality of the Cell Phone Overuse Scale (CPOS) using factor analytic methods. Ordinary least-squares regression models were used to examine associations between identified subscales and measures of impulsivity, alcohol use, and anxious relationship style, to establish convergent validity. We used negative binomial regression models to investigate associations between the CPOS and motor vehicle crash incidence. We found the CPOS to be composed of four subscales: anticipation, activity interfering, emotional reaction, and problem recognition. Each displayed significant associations with aspects of impulsivity, problematic alcohol use, and anxious relationship style characteristics. Only the anticipation subscale demonstrated statistically significant associations with reported motor vehicle crash incidence, controlling for clinical and demographic characteristics (relative ratio, 1.13; confidence interval, 1.01-1.26). For each 1-point increase on the 6-point anticipation subscale, risk for previous motor vehicle crash increased by 13%. Crash risk is strongly associated with heightened anticipation about incoming phone calls or messages. The mean score on the CPOS is associated with increased risk of motor vehicle crash but does not reach statistical significance. Copyright © 2013 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.

41 CFR 102-34.260 - May we replace a Government-owned motor vehicle sooner?

Science.gov (United States)

2010-07-01

... mechanical repairs that exceed the fair market value of the motor vehicle. Determine the fair market value by adding the current market value of the motor vehicle plus any capitalized motor vehicle additions (such...

40 CFR 80.532 - How are motor vehicle diesel fuel credits used and transferred?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false How are motor vehicle diesel fuel... AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel....532 How are motor vehicle diesel fuel credits used and transferred? (a) Credit use stipulations. Motor...

Alternating-Current Motor Drive for Electric Vehicles

Science.gov (United States)

Krauthamer, S.; Rippel, W. E.

1982-01-01

New electric drive controls speed of a polyphase as motor by varying frequency of inverter output. Closed-loop current-sensing circuit automatically adjusts frequency of voltage-controlled oscillator that controls inverter frequency, to limit starting and accelerating surges. Efficient inverter and ac motor would give electric vehicles extra miles per battery charge.

Driver Injury Risk Variability in Finite Element Reconstructions of Crash Injury Research and Engineering Network (CIREN) Frontal Motor Vehicle Crashes.

Science.gov (United States)

Gaewsky, James P; Weaver, Ashley A; Koya, Bharath; Stitzel, Joel D

2015-01-01

A 3-phase real-world motor vehicle crash (MVC) reconstruction method was developed to analyze injury variability as a function of precrash occupant position for 2 full-frontal Crash Injury Research and Engineering Network (CIREN) cases. Phase I: A finite element (FE) simplified vehicle model (SVM) was developed and tuned to mimic the frontal crash characteristics of the CIREN case vehicle (Camry or Cobalt) using frontal New Car Assessment Program (NCAP) crash test data. Phase II: The Toyota HUman Model for Safety (THUMS) v4.01 was positioned in 120 precrash configurations per case within the SVM. Five occupant positioning variables were varied using a Latin hypercube design of experiments: seat track position, seat back angle, D-ring height, steering column angle, and steering column telescoping position. An additional baseline simulation was performed that aimed to match the precrash occupant position documented in CIREN for each case. Phase III: FE simulations were then performed using kinematic boundary conditions from each vehicle's event data recorder (EDR). HIC15, combined thoracic index (CTI), femur forces, and strain-based injury metrics in the lung and lumbar vertebrae were evaluated to predict injury. Tuning the SVM to specific vehicle models resulted in close matches between simulated and test injury metric data, allowing the tuned SVM to be used in each case reconstruction with EDR-derived boundary conditions. Simulations with the most rearward seats and reclined seat backs had the greatest HIC15, head injury risk, CTI, and chest injury risk. Calculated injury risks for the head, chest, and femur closely correlated to the CIREN occupant injury patterns. CTI in the Camry case yielded a 54% probability of Abbreviated Injury Scale (AIS) 2+ chest injury in the baseline case simulation and ranged from 34 to 88% (mean = 61%) risk in the least and most dangerous occupant positions. The greater than 50% probability was consistent with the case occupant's AIS 2

Final Rule for Control of Air Pollution From New Motor Vehicles and New Motor Vehicle Engines; Non-Conformance Penalties for 2004 and later Model Year Emission Standards for Heavy-Duty Diesel Engines and Heavy-Duty Diesel Vehicles

Science.gov (United States)

Final Rule for Control of Air Pollution From New Motor Vehicles and New Motor Vehicle Engines; Non-Conformance Penalties for 2004 and later Model Year Emission Standards for Heavy-Duty Diesel Engines and Heavy-Duty Diesel Vehicles

Slot Optimization Design of Induction Motor for Electric Vehicle

Science.gov (United States)

Shen, Yiming; Zhu, Changqing; Wang, Xiuhe

2018-01-01

Slot design of induction motor has a great influence on its performance. The RMxprt module based on magnetic circuit method can be used to analyze the influence of rotor slot type on motor characteristics and optimize slot parameters. In this paper, the authors take an induction motor of electric vehicle for a typical example. The first step of the design is to optimize the rotor slot by RMxprt, and then compare the main performance of the motor before and after the optimization through Ansoft Maxwell 2D. After that, the combination of optimum slot type and the optimum parameters are obtained. The results show that the power factor and the starting torque of the optimized motor have been improved significantly. Furthermore, the electric vehicle works at a better running status after the optimization.

Fuel cell usage in motor vehicles

International Nuclear Information System (INIS)

Vellone, R.

1998-01-01

Much interest has been aroused by fuel cell usage in motor vehicles, since this technology seems to overcome the conventional limits by other kinds of drive, i.e. the high environmental impact of internal-combustion engines and the drawbacks of electric battery vehicles in terms of maximum operating range and battery recharge time. After 2010 its costs are expected to fall in competitive levels with internal-combustion engines [it

Syncope and Motor Vehicle Crash Risk

DEFF Research Database (Denmark)

Numé, Anna-Karin; Gislason, Gunnar; Christiansen, Christine Benn

2016-01-01

IMPORTANCE: Syncope may have serious consequences for traffic safety. Current clinical guideline recommendations on driving following syncope are primarily based on expert consensus. OBJECTIVE: To identify whether there is excess risk of motor vehicle crashes among patients with syncope compared...... vehicle crashes throughout the follow-up period. This study suggests that syncope should be considered as one of several factors in a broad assessment of fitness to drive....

Electric vehicle traction motors - The development of an advanced motor concept

Science.gov (United States)

Campbell, P.

1980-01-01

An axial-field permanent magnet traction motor is described, similar to several advanced motors that are being developed in the United States. This type of machine has several advantages over conventional dc motors, particularly in the electric vehicle application. The rapidly changing cost of magnetic materials, particularly cobalt, makes it important to study the utilization of permanent magnet materials in such machines. The impact of different magnets on machine design is evaluated, and the advantages of using iron powder composites in the armature are assessed.

Impact of Fiscal Decentralization on Motor Vehicle Taxation in the Slovak Republic

Directory of Open Access Journals (Sweden)

Konečný Vladimír

2016-03-01

Full Text Available The article deals with the motor vehicle tax in relation with fiscal decentralization, particularly from 2005 with competence delegated to the self-governing regions in the area of motor vehicle tax. The result of this provision in the field of fiscal decentralization is increasing of differences in the motor vehicle tax burden in self-governing regions of Slovakia. The paper is the result of solving a series of impact studies solved by the authors in this field. Gradually over time from the transfer of competences in setting tax rates on motor vehicles to self-governing regions and usage of the incomes of this tax can realistically assess the development and impact of this element of fiscal decentralization in the Slovak Republic as well as propose a solution of resulting situation. The aim is to eliminate differences in motor vehicle tax burden at regional and interstate level while maintaining the current level of tax revenues of self-governing regions.

Possibilities of Using Hydrogen as Motor Vehicle Fuel

Directory of Open Access Journals (Sweden)

Zdravko Bukljaš

2005-03-01

Full Text Available Hydrogen is the fuel of the future, since it is the element ofwater (H20 whichsun·ounds us and the resources of which areunlimited. First water is divided into hydrogen and oxygen. Thepaper presents the laboratory and industrial methods of obtain·ing hydrogen, types of fuel cells for various purposes, hydrogen-propelled motor vehicles, as well as advantages and drawbacksof hydrogen used as fuel under the conditions that haveto be met in order to use it as propulsion energy for motor vehicles.

75 FR 43975 - California State Motor Vehicle and Nonroad Engine Pollution Control Standards; Truck Idling...

Science.gov (United States)

2010-07-27

... standards) for the control of emissions from new motor vehicles or new motor vehicle engines prior to March... approval relating to the control of emissions from any new motor vehicle or new motor vehicle engine as... relating to the control of emissions from new nonroad spark-ignition engines smaller than 50 horsepower...

77 FR 20558 - Federal Motor Vehicle Safety Standards; Platform Lifts for Motor Vehicles; Platform Lift...

Science.gov (United States)

2012-04-05

... unrelated to the barrier's safety. Lift-U also questioned the agency's statement that it could be difficult... DEPARTMENT OF TRANSPORTATION National Highway Traffic Safety Administration 49 CFR Part 571 [Docket No. NHTSA-2012-0039] RIN 2127-AJ93 Federal Motor Vehicle Safety Standards; Platform Lifts for...

A survey of protective cushion usage in individuals with spinal cord injury while traveling in a motor vehicle and on a commercial airliner.

Science.gov (United States)

McClure, Isa A; Nieves, Jeremiah D; Kirshblum, Steven C

2014-11-01

While there are specific recommendations for pressure relieving cushions when seated in a wheelchair, there is a paucity of information regarding prescribed wheelchair cushions for persons with spinal cord injury (SCI) when traveling and not in their wheelchair seat. A questionnaire was designed to ascertain if individuals with SCI who are primarily wheelchair users utilize a prescribed wheelchair cushion when traveling in a motor vehicle (MV) or on a commercial airliner, as not utilizing one may be a causative factor in developing pressure ulcers. Survey design in an outpatient SCI rehabilitation setting. Full-time wheelchair users, with chronic (>1 year) SCI. Forty-two participants completed the survey, with a mean age of 39 years old and time post-injury of 10.4 years. All subjects used a prescribed wheelchair cushion when seated in their wheelchair. Twenty-seven subjects reported transferring to a MV seat (59.5% of sample), with 25 (92.6%) reporting not using a prescribed wheelchair cushion when sitting directly on the MV seat. For subjects who traveled on an airplane (n = 23-54.8%), 19 (82.6%) reported that they do not sit on a prescribed specialty cushion. Persons with chronic SCI, who are primary wheelchair users, utilize prescribed wheelchair cushions when sitting in their wheelchair, but most do not utilize a prescribed wheelchair cushion when seated in a MV (if they transfer out of their chair) or on a airplane seat. Studies to determine the pressures over the bony prominences on their travel surfaces may need to be undertaken to see whether the pressures are appropriate, as they may be a source of skin breakdown.

Impact of Active Climate Control Seats on Energy Use, Fuel Use, and CO2 Emissions

Energy Technology Data Exchange (ETDEWEB)

Kreutzer, Cory J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Rugh, John P [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Titov, Eugene V [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kekelia, Bidzina [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-11-28

A project was developed through collaboration between Gentherm and NREL to determine the impact of climate control seats for light-duty vehicles in the United States. The project used a combination of experimentation and analysis, with experimental results providing critical input to the analysis process. First, outdoor stationary vehicle testing was performed at NREL's facility in Golden, CO using multiple occupants. Two pre-production Ford Focus electric vehicles were used for testing; one containing a standard inactive seat and the second vehicle containing a Gentherm climate control seat. Multiple maximum cool-down and steady-state cooling tests were performed in late summer conditions. The two vehicles were used to determine the increase in cabin temperature when using the climate control seat in comparison to the baseline vehicle cabin temperature with a standard seat at the equivalent occupant whole-body sensation. The experiments estimated that on average, the climate control seats allowed for a 2.61 degrees Celsius increase in vehicle cabin temperature at equivalent occupant body sensation compared to the baseline vehicle. The increased cabin air temperature along with their measured energy usage were then used as inputs to the national analysis process. The national analysis process was constructed from full vehicle cabin, HVAC, and propulsion models previously developed by NREL. In addition, three representative vehicle platforms, vehicle usage patterns, and vehicle registration weighted environmental data were integrated into the analysis process. Both the baseline vehicle and the vehicle with climate control seats were simulated, using the experimentally determined cabin temperature offset of 2.61degrees Celsius and added seat energy as inputs to the climate control seat vehicle model. The U.S. composite annual fuel use savings for the climate control seats over the baseline A/C system was determined to be 5.1 gallons of gasoline per year per

A novel dual motor drive system for three wheel electric vehicles

Science.gov (United States)

Panmuang, Piyapat; Thongsan, Taweesak; Suwapaet, Nuchida; Laohavanich, Juckamass; Photong, Chonlatee

2018-03-01

This paper presents a novel dual motor drive system used for three wheel electric vehicles that have one free wheel at the front and two wheels with a drive system at the end of the vehicles. A novel dual motor drive system consists of two identical DC motors that are independently controlled by its speed-torque controller. Under light load conditions, only one of the DC motors will operate around it rated whilst under hard load conditions both of the DC motors will operate. With this drive system, the motors will operate only at its high performance at rated or else no operate to retain longer lifetime. The simulated results for the Skylab three wheel electric vehicle prototype with 8kW at full load (high torque, low speed) and around 4kW at light/normal operating loads (regular speed-torque) showed that the proposed system provides better dynamic responses with faster overshoot current/voltage recovery time, has lower investment costs, has longer lifetime of the motors and allows the motors to always operate at their high performance and thus achieve more cost effective system compared to a single motor drive system with 8kW DC motors.

Physical context management for a motor vehicle

Science.gov (United States)

Dixon, Kevin R [Albuquerque, NM; Forsythe, James C [Sandia Park, NM; Lippitt, Carl E [Albuquerque, NM; Lippitt, legal representative, Lois Diane

2009-10-27

Computer software for and a method of enhancing safety for an operator of a motor vehicle comprising employing a plurality of sensors of vehicle and operator conditions, matching collective output from the sensors against a plurality of known dangerous conditions, and preventing certain activity of the operator if a known dangerous condition is detected.

The malleability of infant motor development: cautions based on studies of child-rearing practices in Yucatan.

Science.gov (United States)

Solomons, H C

1978-11-01

Tests with the Bayley Motor Scale were given to 288 infants, equally divided by sex, in Yucatan, Mexico. These were 2 to 54 weeks in age and came from three sociocultural levels. In comparison to USA infants, early acceleration of motor development was followed by a marked downward trend. This phenomenon, if observed in a single child, may indicate progressive neurologic disease. Child-rearing practices would appear to account for the difference in pattern of test performance.

A social media program to increase adolescent seat belt use.

Science.gov (United States)

Drake, Stacy A; Zhang, Ni; Applewhite, Courtney; Fowler, Katherine; Holcomb, John B

2017-09-01

In response to motor vehicle crashes remaining the leading cause of death for teenagers in the United States, a nursing clinical group (n = 10) in conjunction with a local hospital injury prevention program created an educational campaign to bolster seat belt use. The nursing students created an Instagram account to serve as an educational tool to promote seat belt use among teenagers aged 14-19, and the program was presented at three high school health fairs. In all, 135 postings were made to the account over a 3-month period. The number of likes posted by high school students was the unit of analysis. The most significant result (p = .01) was the difference between postings most liked (celebrities wearing seat belts) and least liked (postings made at the high school health fair), otherwise, differences among postings liked (humor postings, response requests, pictures of celebrities, factual data) were not significant. Instagram user engagement, measured in number of likes, is indicative that social media provides platforms to promote injury prevention efforts. Further research is needed to identify measurable elements of social media and to follow-up on behavioral changes following participation. © 2017 Wiley Periodicals, Inc.

The efficiency of direct torque control for electric vehicle behavior improvement

Directory of Open Access Journals (Sweden)

Gasbaoui Brahim

2011-01-01

Full Text Available Nowadays the electric vehicle motorization control takes a great interest of industrials for commercialized electric vehicles. This paper is one example of the proposed control methods that ensure both safety and stability the electric vehicle by the means of Direct Torque Control (DTC. For motion of the vehicle the electric drive consists of four wheels: two front ones for steering and two rear ones for propulsion equipped with two induction motors, due to their lightweight simplicity and high performance. Acceleration and steering are ensured by the electronic differential, permitting safe and reliable steering at any curve. The direct torque control ensures efficiently controlled vehicle. Electric vehicle direct torque control is simulated in MATLAB SIMULINK environment. Electric vehicle (EV demonstrated satisfactory results in all type of roads constraints: straight, ramp, downhill and bends.

Investigating impact of motor oil quality on vehicles engine induced noise level

Directory of Open Access Journals (Sweden)

I. Arefian

2015-09-01

Full Text Available Introduction: Vehicle engine id one of the main sources of noise which its level is influenced by various parameters. The aim of this study was to investigate the impact of motor oils quality before and after oil change on the variability of vehicle engine induced noise level. In this study it is tried to follow-up the efficacy of motor oil quality on engines sound level. Material and Method: First, engine noise of 94 vehicles were recorded for 30 seconds before and after oil change and all the vehicles technical information including mileage, type of motor oil, and type of vehicle were registered. Following, the recorded noises were calibrated in semi-anechoic chamber and the sound pressure levels were measured with A and C-weighting network and main octav bands, using a sound level meters. The obtained results analyzed using SPSS software version 17. Results: The effects of motor oil quality on different noise levels of engines were determined and a significant reduction in noise level of vehicles engine was observed. Investigation of the relationship between mileage and motor oil quality on various engines sound level manifested that vehicles with mileage ranged 100000-150000 miles had significant reduction in their sound pressure levels in comparison with other vehicles. Conclusion: The results revealed that engine oil is among factors reducing the vehicle engine induced noise level. Moreover, the engine oil type and the vehicle mileage are key variables which determine the impact of engine oil quality on reduction of the sound level of vehicles engine.

Motor vehicle fuel economy, the forgotten HC control stragegy?

Energy Technology Data Exchange (ETDEWEB)

Deluchi, M.; Wang, Quanlu; Greene, D.L.

1992-06-01

Emissions of hydrocarbons from motor vehicles are recognized as major contributors to ozone pollution in urban areas. Petroleum-based motor fuels contain volatile organic compounds (VOC) which, together with oxides of nitrogen, promote the formation of ozone in the troposphere via complex photochemical reactions. VOC emissions from the tailpipe and evaporation from the fuel and engine systems of highway vehicles are believed to account for about 40% of total VOC emissions in any region. But motor fuels also generate emissions throughout the fuel cycle, from crude oil production to refining, storage, transportation, and handling, that can make significant contributions to the total inventory of VOC emissions. Many of these sources of emissions are directly related to the quantity of fuel produced and handled throughout the fuel cycle. It is, therefore, reasonable to expect that a reduction in total fuel throughput might result in a reduction of VOC emissions. In particular, reducing vehicle fuel consumption by increasing vehicle fuel economy should reduce total fuel throughput, thereby cutting total emissions of VOCS. In this report we identify the sources of VOC emissions throughout the motor fuel cycle, quantify them to the extent possible, and describe their dependence on automobile and light truck fuel economy.

On the Costs of Air Pollution from Motor Vehicles

OpenAIRE

Small, Kenneth A.; Kazimi, Camilla

1995-01-01

Air pollution is frequently the stated reason for special measures aimed at controlling motor vehicles. In the United States, motor vehicle emission standards are set explicitly in clean air legislation, while policies at several levels of government are designed to reduce the use of cars for particular purposes like commuting. In Europe, high fuel taxes and subsidies to urban mass transit and intercity rail travel in large part aim to reduce car use.

Accidents involving off-road motor vehicles in a northern community.

Science.gov (United States)

Hasselback, P; Wilding, H R

1987-01-01

The increasing number of accidents associated with off-road motor vehicles used for recreational purposes prompted this prospective study. During 1985 the records of victims of all motor vehicle accidents who were seen at the Hudson Bay Union Hospital, Hudson Bay, Sask., were studied; patients involved in on-road vehicle accidents were included for comparison. Emphasis was placed on age, vehicle type, mechanism of accident, injury severity and the use of safety features. Almost half of the victims of off-road vehicle accidents were under 16 years of age. The poor adherence to government legislation and manufacturer recommendations was evident in the number of people who did not wear helmets or use headlights. PMID:3651929

40 CFR 93.118 - Criteria and procedures: Motor vehicle emissions budget.

Science.gov (United States)

2010-07-01

... emissions budget. 93.118 Section 93.118 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... and procedures: Motor vehicle emissions budget. (a) The transportation plan, TIP, and project not from a conforming transportation plan and TIP must be consistent with the motor vehicle emissions budget...

75 FR 50733 - Preliminary Theft Data; Motor Vehicle Theft Prevention Standard

Science.gov (United States)

2010-08-17

... [Docket No. NHTSA 2010-0098] Preliminary Theft Data; Motor Vehicle Theft Prevention Standard AGENCY... of preliminary theft data; request for comments. SUMMARY: This document requests comments on data about passenger motor vehicle thefts that occurred in calendar year (CY) 2008 including theft rates for...

Selective detection and characterization of nanoparticles from motor vehicles.

Science.gov (United States)

Johnston, Murray V; Klems, Joseph P; Zordan, Christopher A; Pennington, M Ross; Smith, James N

2013-02-01

Numerous studies have shown that exposure to motor vehicle emissions increases the probability of heart attacks, asthma attacks, and hospital visits among at-risk individuals. However, while many studies have focused on measurements of ambient nanoparticles near highways, they have not focused on specific road-level domains, such as intersections near population centers. At these locations, very intense spikes in particle number concentration have been observed. These spikes have been linked to motor vehicle activity and have the potential to increase exposure dramatically. Characterizing both the contribution and composition of these spikes is critical in developing exposure models and abatement strategies. To determine the contribution of the particle spikes to the ambient number concentration, we implemented wavelet-based algorithms to isolate the particle spikes from measurements taken during the summer and winter of 2009 in Wilmington, Delaware, adjacent to a roadway intersection that approximately 28,000 vehicles pass through daily. These measurements included both number concentration and size distributions recorded once every second by a condensation particle counter (CPC*; TSI, Inc., St. Paul, MN) and a fast mobility particle sizer (FMPS). The high-frequency portion of the signal, consisting of a series of abrupt spikes in number concentration that varied in length from a few seconds to tens of seconds, accounted for 3% to 35% of the daily ambient number concentration, with spike contributions sometimes greater than 50% of hourly number concentrations. When the data were weighted by particle volume, this portion of the signal contributed an average of 10% to 20% to the daily concentration of particulate matter (PM) vehicles accelerated after a red traffic light turned green. As the distance or transit time from emission to sampling increased, the size distribution shifted to a larger particle size, which confirmed the source assignments. To determine the

A geography of moral hazard: sources and sinks of motor-vehicle commuting externalities.

Science.gov (United States)

Yiannakoulias, Niko; Bland, Widmer; Scott, Darren M

2014-09-01

Motor-vehicles are responsible for harms to health that are not directly experienced by individual drivers - such as air pollution and risk of injury to pedestrians. In addition to their direct effects on health, these harms also represent a moral hazard since drivers are not required to consider their effects as part of their decision to drive. We describe an approach for estimating sources of motor-vehicle commuter externalities as a means of understanding the geography of moral hazard, and in particular, the spatial displacement of negative health externalities associated with motor-vehicle commuting. This approach models motor-vehicle commuter traffic flow by trip origin for small geographic areas within the City of Toronto, Ontario. We find that most health-related externalities associated with motor-vehicle commuters are not locally generated, with a large share coming from outside Toronto. Low income is associated with externalities originating outside the municipal boundary, but not with locally sourced externalities. We discuss the impact of geographical moral hazard on the agency of citizens as well as policy options aimed at addressing motor-vehicle externalities. Copyright © 2014 Elsevier Ltd. All rights reserved.

New Approaches for Estimating Motor Vehicle Emissions in Megacities

Science.gov (United States)

Marr, L. C.; Thornhill, D. A.; Herndon, S. C.; Onasch, T. B.; Wood, E. C.; Kolb, C. E.; Knighton, W. B.; Mazzoleni, C.; Zavala, M. A.; Molina, L. T.

2007-12-01

The rapid proliferation of megacities and their air quality problems is producing unprecedented air pollution health risks and management challenges. Quantifying motor vehicle emissions in the developing world's megacities, where vehicle ownership is skyrocketing, is critical for evaluating the cities' impacts on the atmosphere at urban, regional, and global scales. The main goal of this research is to quantify gasoline- and diesel-powered motor vehicle emissions within the Mexico City Metropolitan Area (MCMA). We apply positive matrix factorization to fast measurements of gaseous and particulate pollutants made by the Aerodyne Mobile Laboratory as it drove throughout the MCMA in 2006. We consider carbon dioxide; carbon monoxide; volatile organic compounds including benzene and formaldehyde; nitrogen oxides; ammonia; fine particulate matter; particulate polycyclic aromatic hydrocarbons; and black carbon. Analysis of the video record confirms the apportionment of emissions to different engine types. From the derived source profiles, we calculate fuel-based fleet-average emission factors and then estimate the total motor vehicle emission inventory. The advantages of this method are that it can capture a representative sample of vehicles in a variety of on-road driving conditions and can separate emissions from gasoline versus diesel engines. The results of this research can be used to help assess the accuracy of emission inventories and to guide the development of strategies for reducing vehicle emissions.

Non-isolated integrated motor drive and battery charger based on the split-phase PM motor for plug-in vehicles

OpenAIRE

Serrano Guillén, Isabel; Bermejo Fernández, Álvaro

2013-01-01

In electric vehicles and plug-in hybrid electric vehicles, the utility grid charges the vehicle battery through a battery charger. Different solutions have been proposed to reduce the size and cost of the charger. One solution to achieve this is to include the devices used in the traction circuit in the charger circuit; this is called an integrated motor drive and battery charger. A split-phase PM motor, a motor with double set of windings, gives the opportunity to implement different wind...

NRC Information No. 90-21: Potential failure of motor-operated butterfly valves to operate because valve seat friction was underestimated

International Nuclear Information System (INIS)

Rossi, C.E.

1992-01-01

In October 1988, at Catawba Nuclear Station Unit 1, a motor-operated butterfly valve in the service water system failed to open under high differential pressure conditions. The licensee concluded that the valve manufacturer, BIF/General Signal Corporation, had underestimated the degree to which the material used in the valve seat would harden with age (the responsibility for these valves has been transferred to Paul-Munroe Enertech). This underestimation of the age hardening had led the manufacturer to assume valve seat friction forces that were less than the actual friction forces in the installed valve. To overcome the larger-than-anticipated friction forces, the licensee's engineering staff recommended the open torque switch for 56 butterfly valves be reset to the maximum allowable value. The systems in which these valves are located include the component cooling water system, service water system, and various ventilation systems. By July 26, 1989, the torque switch adjustments were completed at Catawba Units 1 and 2. After reviewing the final settings, the licensee's engineering staff determined that the actuators for three butterfly valves in the component cooling water system might not be able to overcome the friction forces resulting from maximum seat hardening. On December 13, 1989, the licensee determined that the failure of these BIF/General Signal motor-operated valves (MOVs) could cause a loss of cooling water to residual heat removal system heat exchangers. To resolve the concern regarding the operability of these BIF/General Signal valves, a torque switch bypass was installed on two of the actuators to allow full motor capability during opening

Analysis of vibroprotection characteristics of pneumatic relaxation seat suspension with capability of vibration energy recuperation

Directory of Open Access Journals (Sweden)

Lyashenko Mikhail

2017-01-01

Full Text Available This paper proposes mechanism and control algorithm for pneumatic relaxation system of suspension with vibration energy recuperation applied to standard vehicle operator seat (“Sibeko” company. Mathematical model of the seat pneumatic relaxation suspension with two additional air volumes was created. Pneumatic motor – recuperator activated by means of air flow from the one additional volume to another is installed in air piping between additional volumes. Computational research was made in Matlab/Simulink. Amplitude-frequency characteristics of transmission coefficient for standard and proposed suspensions were plotted for preliminary evaluation of vibration protection properties of seat suspension. Performed comparative analysis of amplitude-frequency characteristics shows that noticeable improvement of vibration protection properties of pneumatic relaxation suspension system with vibration energy recuperation in comparison with standard system both in region of resonance disturbances and in above-resonance region. Main ways for further improvement of vibration protection properties of proposed system were marked out.

Patterns of seatbelt use in different socioeconomic communities in ...

African Journals Online (AJOL)

All occupants were eligible for inclusion except occupants of non-motorised vehicles, two-wheel motorised vehicles, buses, taxis, heavy goods vehicles and emergency vehicles. ... (n=2 513) for drivers, 33.1% (n=521) for front-seat passengers (adults 33.2%, n=452; children 32.7%, n=69) and 9.0% (n=56) for rear-seat

Measuring a conceptual model of the relationship between compulsive cell phone use, in-vehicle cell phone use, and motor vehicle crash.

Science.gov (United States)

O'Connor, Stephen S; Shain, Lindsey M; Whitehill, Jennifer M; Ebel, Beth E

2017-02-01

Previous research suggests that anticipation of incoming phone calls or messages and impulsivity are significantly associated with motor vehicle crash. We took a more explanative approach to investigate a conceptual model regarding the direct and indirect effect of compulsive cell phone use and impulsive personality traits on crash risk. We recruited a sample of 307 undergraduate college students to complete an online survey that included measures of cell phone use, impulsivity, and history of motor vehicle crash. Using a structural equation model, we examined the direct and indirect relationships between factors of the Cell Phone Overuse Scale-II (CPOS-II), impulsivity, in-vehicle phone use, and severity and frequency of previous motor vehicle crash. Self-reported miles driven per week and year in college were included as covariates in the model. Our findings suggest that anticipation of incoming communication has a direct association with greater in-vehicle phone use, but was not directly or indirectly associated with increasing risk of previous motor vehicle crash. Of the three latent factors comprising the CPOS-II, only anticipation was significantly associated with elevated cell phone use while driving. Greater impulsivity and use of in-vehicle cell phone use while driving were directly and significantly associated with greater risk of motor vehicle crash. Anticipation of incoming cellular contacts (calls or texts) is associated with greater in-vehicle phone use, while greater in-vehicle cell phone use and impulsive traits are associated with elevated risk of motor vehicle crashes. Copyright © 2017 Elsevier Ltd. All rights reserved.

75 FR 6123 - Federal Motor Vehicle Safety Standards; Occupant Crash Protection

Science.gov (United States)

2010-02-08

... motor vehicle safety standard is in effect under this chapter, a State or a political subdivision of a... [Docket No. NHTSA-2009-0156] RIN 2127-AK57 Federal Motor Vehicle Safety Standards; Occupant Crash...'s response to petitions for reconsideration of a November 12, 2008 final rule that amended the child...

Developing particulate thin filter using coconut fiber for motor vehicle emission

Science.gov (United States)

Wardoyo, A. Y. P.; Juswono, U. P.; Riyanto, S.

2016-03-01

Amounts of motor vehicles in Indonesia have been recognized a sharply increase from year to year with the increment reaching to 22 % per annum. Meanwhile motor vehicles produce particulate emissions in different sizes with high concentrations depending on type of vehicles, fuels, and engine capacity. Motor Particle emissions are not only to significantly contribute the atmosphric particles but also adverse to human health. In order to reduce the particle emission, it is needed a filter. This study was aimed to develop a thin filter using coconut fiber to reduce particulate emissions for motor vehicles. The filter was made of coconut fibers that were grinded into power and mixed with glues. The filter was tested by the measurements of particle concentrations coming out from the vehicle exhaust directly and the particle concentrations after passing through the filter. The efficiency of the filter was calculated by ratio of the particle concentrations before comming in the filter to the particle conentrations after passing through the filter. The results showed that the efficiency of the filter obtained more than 30 %. The efficiency increases sharply when a number of the filters are arranged paralelly.

DEVELOPING CONVENIENT MOTOR SELECTION ALGORITHM ACCORDING TO ROAD CONDITIONS IN ELECTRIC VEHICLES

OpenAIRE

BAŞER, EKREM; ALTUN, YUSUF

2016-01-01

Nowadays, automotive industry is tending to electric vehicles due to reduction of fuel reserves in order to save energy, reduce air pollution and carbon emission. With the impact of technological advencements on battery and power electronics, the studies on electric vehicles have been gradually increased and many of automobile manifacturers have produced new electric vehicles. Different type of electric motors has been tried on electric vehicles until today. This motors have difference feautu...

Vehicle Dynamics Control of In-wheel Electric Motor Drive Vehicles Based on Averaging of Tire Force Usage

Science.gov (United States)

Masaki, Nobuo; Iwano, Haruo; Kamada, Takayoshi; Nagai, Masao

For in-wheel electric motor drive vehicles, a new vehicle dynamics control which is based on the tire force usage rate is proposed. The new controller adopts non-linear optimal control could manage the interference between direct yaw-moment control and the tire force usage rate. The new control is considered total longitudinal and transverse tire force. Therefore the controller can prevent tire force saturation near tire force limit during cornering. Simulations and test runs by the custom made four wheel drive in-wheel motor electric vehicle show that higher driving stability performance compared to the performance of the same vehicle without control.

Development of electrostatic charging evaluation equipment for automobile seat; Jidoshayo seat no taidensei shiken hyoka sochi no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Maeda, K [Mazda Motor Corp., Hiroshima (Japan)

1997-10-01

When passengers get out of vehicle, electrostatics is generated by separation of seat cloth and passenger cloth, and then charged to passenger`s body. It has been impossible for us to simulate this induction charging phenomenon with current evaluation equipments. We developed a new seat cloth evaluation equipments using induction charging plate, which enables us to simulate the phenomenon. This paper describes this new electrostatic charging evaluation method for automobile seat cloth. 5 refs., 6 figs.

Comparative study of potential whiplash injuries for different occupant seated positions during rear end accidents.

Science.gov (United States)

Omerović, Senad; Tomasch, Ernst; Gutsche, Andreas J; Prebil, Ivan

2016-01-01

Whiplash injuries to the cervical spine represent a considerable economic burden on society with medical conditions, in some cases persisting for more than a year. Numerous studies of whiplash injuries have been made for occupant normal seated position, leaving the analysis of neck injuries for out-of-normal positions not well documented. For that purpose, a detailed human cervical spine finite element model was developed. The analysis was made for four most common occupant seated positions, such as: Normal Position with the torso against the seat back and the head looking straight ahead, Torso Lean forward position with the torso away from the seat back for approximately 10°, Head Flexed position with the head flexed forward approximately 20° from the normal position and Head-Flexed with Torso Lean forward position with the head flexed forward approximately 20° and torso 10° from the normal position. The comparative study included the analysis of capsular ligament deformation and the level of S-curvature of the cervical spine. The model developed predicted that Head Flexed seated position and Head-Flexed with Torso Lean forward seated position are most threatening for upper and lower cervical spine capsular ligament, respectively. As for the level of S-curvature, the model predicted that Head-Flexed with Torso Lean forward seated position would be most prone to neck injuries associated with it. This study demonstrated that the occupant seated position has a significant influence on potential whiplash injuries.

A Hydraulic Motor-Alternator System for Ocean-Submersible Vehicles

Science.gov (United States)

Aintablian, Harry O.; Valdez, Thomas I.; Jones, Jack A.

2012-01-01

An ocean-submersible vehicle has been developed at JPL that moves back and forth between sea level and a depth of a few hundred meters. A liquid volumetric change at a pressure of 70 bars is created by means of thermal phase change. During vehicle ascent, the phase-change material (PCM) is melted by the circulation of warm water and thus pressure is increased. During vehicle descent, the PCM is cooled resulting in reduced pressure. This pressure change is used to generate electric power by means of a hydraulic pump that drives a permanent magnet (PM) alternator. The output energy of the alternator is stored in a rechargeable battery that powers an on-board computer, instrumentation and other peripherals.The focus of this paper is the performance evaluation of a specific hydraulic motor-alternator system. Experimental and theoretical efficiency data of the hydraulic motor and the alternator are presented. The results are used to evaluate the optimization of the hydraulic motor-alternator system. The integrated submersible vehicle was successfully operated in the Pacific Ocean near Hawaii. A brief overview of the actual test results is presented.

75 FR 23306 - Establishment of Advisory Committee on the National Motor Vehicle Title Information System

Science.gov (United States)

2010-05-03

... Advisory Committee on the National Motor Vehicle Title Information System AGENCY: Office of Justice Programs (OJP), Justice. ACTION: Notice of establishment of the National Motor Vehicle Title Information System (NMVTIS) Advisory Board. SUMMARY: Pursuant to the National Motor Vehicle Title Information System...

77 FR 15351 - Federal Motor Vehicle Safety Standards; Theft Protection and Rollaway Prevention

Science.gov (United States)

2012-03-15

... [Docket No. NHTSA-2011-0174] RIN 2127-AK88 Federal Motor Vehicle Safety Standards; Theft Protection and... (NPRM) to amend Federal Motor Vehicle Safety Standard (FMVSS) No. 114, Theft Protection and Rollaway... requesting that certain information, including vehicle owner questionnaires (VOQs) referenced in the NPRM, be...

78 FR 3081 - Petition for Exemption From the Federal Motor Vehicle Motor Theft Prevention Standard; Toyota

Science.gov (United States)

2013-01-15

... From the Federal Motor Vehicle Motor Theft Prevention Standard; Toyota AGENCY: National Highway Traffic.... SUMMARY: This document grants in full Toyota Motor North America, Inc.'s (Toyota) petition for an... a petition dated October 16, 2012, Toyota requested an exemption from the parts-marking requirements...

76 FR 12221 - Petition for Exemption From the Federal Motor Vehicle Motor Theft Prevention Standard; Toyota

Science.gov (United States)

2011-03-04

... From the Federal Motor Vehicle Motor Theft Prevention Standard; Toyota AGENCY: National Highway Traffic.... SUMMARY: This document grants in full the petition of Toyota Motor North America, Inc's., (Toyota... INFORMATION: In a petition dated January 24, 2011, Toyota requested an exemption from the parts-marking...

General Motors natural gas vehicle initiatives

International Nuclear Information System (INIS)

Weber, J.; Koplow, M.D.

1992-01-01

General Motors (GM) has a number of natural gas vehicle (NGV) programs in progress that address various marketing, technical, and production planning issues that lean on the introduction of NGVs from GM. The initial target is light and medium duty trucks sold in non-attainment air quality regions. GM has also embarked on a longer term program that encompasses vehicle and systems development, gas supply and infrastructure development, and customer and market development. The major long-term issues are gas quality, supplier participation, and infrastructure

Electric machine for hybrid motor vehicle

Science.gov (United States)

Hsu, John Sheungchun

2007-09-18

A power system for a motor vehicle having an internal combustion engine and an electric machine is disclosed. The electric machine has a stator, a permanent magnet rotor, an uncluttered rotor spaced from the permanent magnet rotor, and at least one secondary core assembly. The power system also has a gearing arrangement for coupling the internal combustion engine to wheels on the vehicle thereby providing a means for the electric machine to both power assist and brake in relation to the output of the internal combustion engine.

Motor Vehicle Safety (A Cup of Health with CDC)

Centers for Disease Control (CDC) Podcasts

In our highly mobile society, travel in vehicles is an almost daily occurrence for most Americans. Every trip places us at risk for serious injury. In this podcast, Dr. Gwen discusses ways to avoid serious injuries in motor vehicles.

77 FR 4396 - Petition for Exemption From the Federal Motor Vehicle Motor Theft Prevention Standard; Toyota

Science.gov (United States)

2012-01-27

... From the Federal Motor Vehicle Motor Theft Prevention Standard; Toyota AGENCY: National Highway Traffic... exemption. SUMMARY: This document grants in full the petition of Toyota Motor North America, Inc's., (Toyota.... SUPPLEMENTARY INFORMATION: In a petition dated September 30, 2011, Toyota requested an exemption from the parts...

The influence of motor vehicle legislation on injury claim incidence.

Science.gov (United States)

Lemstra, Mark; Olszynski, W P

2005-01-01

Although there have been numerous strategies to prevent motor vehicle collisions and their subsequent injuries, few have been effective in preventing motor vehicle injury claims. In this paper, we examine the role of legislation and compensation system in altering injury claim incidence. The population base for our natural experiment was all Saskatchewan, Manitoba, British Columbia and Quebec residents who submitted personal injury claims to their respective motor vehicle insurance provider from 1990 to 1999. The provinces of Saskatchewan and Manitoba switched from Tort to pure No-Fault insurance on January 1, 1995 and on March 1, 1994 respectively. British Columbia maintained tort insurance and Quebec maintained pure no-fault insurance throughout the entire 10-year period. The conversion from tort insurance to pure no-fault motor vehicle insurance resulted in a five-year 31% (RR = 0.69; 95% CI 0.68-0.70) reduction in total injury claims per 100,000 residents in Saskatchewan and a five-year 43% (RR = 0.57; 95% CI 0.56-0.58) reduction in Manitoba. At the same time, the province of British Columbia retained tort insurance and had a five-year 5% reduction (RR = 0.95; 95% CI 0.94-0.99). Quebec, which retained pure no-fault throughout the entire 10-year period, had less than one third of the injury claims per 100,000 residents than the tort province of British Columbia. The conversion from tort to pure no-fault legislation has a large influence in reducing motor vehicle injury claim incidence in Canada. Legislative system and injury compensation scheme have an observable impact on injury claim incidence and can therefore have significant impact on the health care system.

World-wide developments in motor vehicle inspection/maintenance (I/M) programs

Energy Technology Data Exchange (ETDEWEB)

Klausmeier, R. [Consulting Inc., Austin, TX (United States); Kishan, S. [Radian Corporation, Austin, TX (United States)

1995-12-31

Motor vehicles contribute much to urban air pollution. As a result, most governments have enacted emission standards that significantly lower pollutant emission levels from new motor vehicles. For example, vehicles built in the United States emit 95 % fewer pollutants than uncontrolled vehicles when they are new. However, studies indicate that proper maintenance is needed to obtain the full benefit of vehicle emission controls. Furthermore, there is evidence that a significant percentage of the vehicle fleet is not properly maintained. This has led to the creation of motor vehicle Inspection/Maintenance (I/M) Programs. I/M programs inspect vehicles for indications that they are emitting excessive quantities of pollutants. Vehicles that fail the inspection must be repaired in order to comply with program requirements. The first I/M programs were implemented in the United States in the early 1970s. With substantial urging from the federal government, most of the U.S. states with severe air pollution problems have implemented I/M programs. Recently, with the passage of the U.S. Clean Air Act Amendments of 1990, many states have been required to significantly upgrade the performance and coverage of their I/M programs. I/M programs also have been implemented in Europe and recently in Asia. This presentation reviews developments in I/M programs for light-duty gasoline powered vehicles. Developments in I/M programs for diesel powered vehicles are briefly described. (author)

World-wide developments in motor vehicle inspection/maintenance (I/M) programs

Energy Technology Data Exchange (ETDEWEB)

Klausmeier, R [Consulting Inc., Austin, TX (United States); Kishan, S [Radian Corporation, Austin, TX (United States)

1996-12-31

Motor vehicles contribute much to urban air pollution. As a result, most governments have enacted emission standards that significantly lower pollutant emission levels from new motor vehicles. For example, vehicles built in the United States emit 95 % fewer pollutants than uncontrolled vehicles when they are new. However, studies indicate that proper maintenance is needed to obtain the full benefit of vehicle emission controls. Furthermore, there is evidence that a significant percentage of the vehicle fleet is not properly maintained. This has led to the creation of motor vehicle Inspection/Maintenance (I/M) Programs. I/M programs inspect vehicles for indications that they are emitting excessive quantities of pollutants. Vehicles that fail the inspection must be repaired in order to comply with program requirements. The first I/M programs were implemented in the United States in the early 1970s. With substantial urging from the federal government, most of the U.S. states with severe air pollution problems have implemented I/M programs. Recently, with the passage of the U.S. Clean Air Act Amendments of 1990, many states have been required to significantly upgrade the performance and coverage of their I/M programs. I/M programs also have been implemented in Europe and recently in Asia. This presentation reviews developments in I/M programs for light-duty gasoline powered vehicles. Developments in I/M programs for diesel powered vehicles are briefly described. (author)

78 FR 2797 - Federal Motor Vehicle Safety Standards; Minimum Sound Requirements for Hybrid and Electric Vehicles

Science.gov (United States)

2013-01-14

... Sound Requirements for Hybrid and Electric Vehicles; Draft Environmental Assessment for Rulemaking To Establish Minimum Sound Requirements for Hybrid and Electric Vehicles; Proposed Rules #0;#0;Federal Register...-0148] RIN 2127-AK93 Federal Motor Vehicle Safety Standards; Minimum Sound Requirements for Hybrid and...

Characterization of metals emitted from motor vehicles.

Science.gov (United States)

Schauer, James J; Lough, Glynis C; Shafer, Martin M; Christensen, William F; Arndt, Michael F; DeMinter, Jeffrey T; Park, June-Soo

2006-03-01

A systematic approach was used to quantify the metals present in particulate matter emissions associated with on-road motor vehicles. Consistent sampling and chemical analysis techniques were used to determine the chemical composition of particulate matter less than 10 microm in aerodynamic diameter (PM10*) and particulate matter less than 2.5 microm in aerodynamic diameter (PM2.5), including analysis of trace metals by inductively coupled plasma mass spectrometry (ICP-MS). Four sources of metals were analyzed in emissions associated with motor vehicles: tailpipe emissions from gasoline- and diesel-powered vehicles, brake wear, tire wear, and resuspended road dust. Profiles for these sources were used in a chemical mass balance (CMB) model to quantify their relative contributions to the metal emissions measured in roadway tunnel tests in Milwaukee, Wisconsin. Roadway tunnel measurements were supplemented by parallel measurements of atmospheric particulate matter and associated metals at three urban locations: Milwaukee and Waukesha, Wisconsin, and Denver, Colorado. Ambient aerosol samples were collected every sixth day for one year and analyzed by the same chemical analysis techniques used for the source samples. The two Wisconsin sites were studied to assess the spatial differences, within one urban airshed, of trace metals present in atmospheric particulate matter. The measurements were evaluated to help understand source and seasonal trends in atmospheric concentrations of trace metals. ICP-MS methods have not been widely used in analyses of ambient aerosols for metals despite demonstrated advantages over traditional techniques. In a preliminary study, ICP-MS techniques were used to assess the leachability of trace metals present in atmospheric particulate matter samples and motor vehicle source samples in a synthetic lung fluid.

Improved transistorized AC motor controller for battery powered urban electric passenger vehicles

Science.gov (United States)

Peak, S. C.

1982-01-01

An ac motor controller for an induction motor electric vehicle drive system was designed, fabricated, tested, evaluated, and cost analyzed. A vehicle performance analysis was done to establish the vehicle tractive effort-speed requirements. These requirements were then converted into a set of ac motor and ac controller requirements. The power inverter is a three-phase bridge using power Darlington transistors. The induction motor was optimized for use with an inverter power source. The drive system has a constant torque output to base motor speed and a constant horsepower output to maximum speed. A gear shifting transmission is not required. The ac controller was scaled from the base 20 hp (41 hp peak) at 108 volts dec to an expanded horsepower and battery voltage range. Motor reversal was accomplished by electronic reversal of the inverter phase sequence. The ac controller can also be used as a boost chopper battery charger. The drive system was tested on a dynamometer and results are presented. The current-controlled pulse width modulation control scheme yielded improved motor current waveforms. The ac controller favors a higher system voltage.

75 FR 2589 - Petition for Exemption From the Federal Motor Vehicle Theft Prevention Standard; Chrysler

Science.gov (United States)

2010-01-15

... From the Federal Motor Vehicle Theft Prevention Standard; Chrysler AGENCY: National Highway Traffic... Jeep Patriot vehicle line in accordance with 49 CFR Part 543, Exemption from Vehicle Theft Prevention... vehicle theft as compliance with the parts-marking requirements of 49 CFR Part 541, Federal Motor Vehicle...

75 FR 53375 - Petition for Exemption From the Federal Motor Vehicle Theft Prevention Standard; Chrysler

Science.gov (United States)

2010-08-31

... From the Federal Motor Vehicle Theft Prevention Standard; Chrysler AGENCY: National Highway Traffic... the Fiat 500 vehicle line in accordance with 49 CFR Part 543, Exemption From Vehicle Theft Prevention... vehicle theft as compliance with the parts-marking requirements of 49 CFR Part 541, Federal Motor Vehicle...

Child seat belt guidelines: Examining the 4 feet 9 inches rule as the standard.

Science.gov (United States)

Morse, Amber M; Aitken, Mary E; Mullins, Samantha H; Miller, Beverly K; Pomtree, Mindy M; Ulloa, Erin M; Montgomery, Jeffrey S; Saylors, Marie E

2017-11-01

Current American Academy of Pediatrics recommendations regarding transition from child safety/booster seat to adult safety belt use indicate that children should be at least 4 feet 9 inches, 8 years old, or 80 pounds. Proper fit in the vehicle seat, assessed with a five-point fit test, should also be met. Although most children reach 4 feet 9 inches around age 8 years, each child and vehicle presents a unique combination; thus a child may not fit appropriately in all vehicle types using only the 4 feet 9 inches requirement. We enrolled children, aged 7 years to 12 years, into our study. Height, weight, and demographic data were obtained. A Child Passenger Safety Technician then performed the five-point fit test in each of a uniform lineup of five vehicles. Data were collected on fit in the standard vehicle seat and also in a booster seat. We set 90% as the threshold proportion of children who meet all criteria for proper fit to validate current recommendations of a height of 4 feet 9 inches. Data were collected on 388 children. The percentage of 90% proper fit was met in the compact car and small sport-utility vehicle (SUV). However, only 80 (77%) of 104 students (p guidelines for an adult seat belt do not meet safety requirements for fit, especially in larger, commonly used vehicles (large SUVs and trucks). This emphasizes the need for evaluation of fit by a trained personnel and/or development of standard back seat dimensions in all vehicles for maximum safety. Epidemiologic level 1.

Active Suspension of Truck Seat

Directory of Open Access Journals (Sweden)

Masaaki Kawana

1998-01-01

Full Text Available The driver’s seat of a heavy duty truck is usually mounted on a spring–damper assembly anchored to the cab floor. To improve riding comfort, this study investigated the effects of mounting a computer-controlled actuator in parallel with the traditional spring–damper assembly. A dynamic model of the seat is represented by a two degree-of-freedom system, including a cushion. In this paper, a control system is designed, using optimal control theory, which minimizes rms vertical acceleration at a point representing the driver’s hip point. In this system, accelerations of the hip point, the seat frame and the cab floor are picked up and integrated to obtain the state variables to be fed back and fed forward to the actuator through a digital computer. The actuator is constructed with electric servo-motor and ball-screw mechanism. The experimental study was carried out on a shaker, which simulates the vibrations of the cab floor in actual service. Results were obtained for both a dummy and a real human body. The vibration test produced rms accelerations of the seat and the hip point of about 1.0 m/s2 without the actuator, while the rms accelerations were suppressed to about 0.5 m/s2 at a rms input voltage to the servo-motor of 1.0 V.

40 CFR 80.596 - How is a refinery motor vehicle diesel fuel volume baseline calculated?

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false How is a refinery motor vehicle diesel... Requirements § 80.596 How is a refinery motor vehicle diesel fuel volume baseline calculated? (a) For purposes of this subpart, a refinery's motor vehicle diesel fuel volume baseline is calculated using the...

Factors contributing to commercial vehicle rear-end conflicts in China: A study using on-board event data recorders.

Science.gov (United States)

Bianchi Piccinini, Giulio; Engström, Johan; Bärgman, Jonas; Wang, Xuesong

2017-09-01

In the last 30years, China has undergone a dramatic increase in vehicle ownership and a resulting escalation in the number of road crashes. Although crash figures are decreasing today, they remain high; it is therefore important to investigate crash causation mechanisms to further improve road safety in China. To shed more light on the topic, naturalistic driving data was collected in Shanghai as part of the evaluation of a behavior-based safety service. The data collection included instrumenting 47 vehicles belonging to a commercial fleet with data acquisition systems. From the overall sample, 91 rear-end crash or near-crash (CNC) events, triggered by 24 drivers, were used in the analysis. The CNC were annotated by three researchers, through an expert assessment methodology based on videos and kinematic variables. The results show that the main factor behind the rear-end CNC was the adoption of very small safety margins. In contrast to results from previous studies in the US, the following vehicles' drivers typically had their eyes on the road and reacted quickly in response to the evolving conflict in most events. When delayed reactions occurred, they were mainly due to driving-related visual scanning mismatches (e.g., mirror checks) rather than visual distraction. Finally, the study identified four main conflict scenarios that represent the typical development of rear-end conflicts in this data. The findings of this study have several practical applications, such as informing the specifications of in-vehicle safety measures and automated driving and providing input into the design of coaching/training procedures to improve the driving habits of drivers. Copyright © 2017 The Authors. Published by Elsevier Ltd.. All rights reserved.

76 FR 61095 - California State Motor Vehicle Pollution Control Standards; Within the Scope Determination and...

Science.gov (United States)

2011-10-03

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9474-5] California State Motor Vehicle Pollution Control... longer expected to produce fuel-cell vehicles to meet part of its gold vehicle credit requirements for... motor vehicle pollution control program. Because EPA has not received adverse public comment challenging...

Assessing Constraints on Soldier Cognitive and Perceptual Motor Performance During Vehicle Motion

Science.gov (United States)

2008-05-01

vehicle systems are biomechanical (Sirouspour & Salcudean, 2003; Sövényi & Gillespie, 2007), cognitive (Parasuraman & Riley, 1997), and psychomotor...vs. velocity), pedals for braking/acceleration Environmental constraints associated with the support surface (Seat): Damping, inclination...steering and secondarily, performance differences between a joystick and pedals for throttle and brake control. Eleven participants com- pleted three

Improved SCR ac Motor Controller for Battery Powered Urban Electric Vehicles

Science.gov (United States)

Latos, T. S.

1982-01-01

An improved ac motor controller, which when coupled to a standard ac induction motor and a dc propulsion battery would provide a complete electric vehicle power train with the exception of the mechanical transmission and drive wheels was designed. In such a system, the motor controller converts the dc electrical power available at the battery terminals to ac electrical power for the induction motor in response to the drivers commands. The performance requirements of a hypothetical electric vehicle with an upper weight bound of 1590 kg (3500 lb) were used to determine the power rating of the controller. Vehicle acceleration capability, top speed, and gradeability requisites were contained in the Society of Automotive Engineers (SAE) Schedule 227a(d) driving cycle. The important capabilities contained in this driving cycle are a vehicle acceleration requirement of 0 to 72.4 kmph (0 to 45 mph) in 28 seconds a top speed of 88.5 kmph (55 mph), and the ability to negotiate a 10% grade at 48 kmph (30 mph). A 10% grade is defined as one foot of vertical rise per 10 feet of horizontal distance.

Identification and validation of a logistic regression model for predicting serious injuries associated with motor vehicle crashes.

Science.gov (United States)

Kononen, Douglas W; Flannagan, Carol A C; Wang, Stewart C

2011-01-01

A multivariate logistic regression model, based upon National Automotive Sampling System Crashworthiness Data System (NASS-CDS) data for calendar years 1999-2008, was developed to predict the probability that a crash-involved vehicle will contain one or more occupants with serious or incapacitating injuries. These vehicles were defined as containing at least one occupant coded with an Injury Severity Score (ISS) of greater than or equal to 15, in planar, non-rollover crash events involving Model Year 2000 and newer cars, light trucks, and vans. The target injury outcome measure was developed by the Centers for Disease Control and Prevention (CDC)-led National Expert Panel on Field Triage in their recent revision of the Field Triage Decision Scheme (American College of Surgeons, 2006). The parameters to be used for crash injury prediction were subsequently specified by the National Expert Panel. Model input parameters included: crash direction (front, left, right, and rear), change in velocity (delta-V), multiple vs. single impacts, belt use, presence of at least one older occupant (≥ 55 years old), presence of at least one female in the vehicle, and vehicle type (car, pickup truck, van, and sport utility). The model was developed using predictor variables that may be readily available, post-crash, from OnStar-like telematics systems. Model sensitivity and specificity were 40% and 98%, respectively, using a probability cutpoint of 0.20. The area under the receiver operator characteristic (ROC) curve for the final model was 0.84. Delta-V (mph), seat belt use and crash direction were the most important predictors of serious injury. Due to the complexity of factors associated with rollover-related injuries, a separate screening algorithm is needed to model injuries associated with this crash mode. Copyright © 2010 Elsevier Ltd. All rights reserved.

Undiagnosed post-traumatic stress disorder following motor vehicle accidents.

Science.gov (United States)

Green, M M; McFarlane, A C; Hunter, C E; Griggs, W M

1993-10-18

To determine the pattern of emergence of post-traumatic stress disorder (PTSD) among motor vehicle accident victims and to examine the influence of PTSD on subsequent levels of disability. A longitudinal study of motor vehicle accident victims one month and 18 months after the accident. Twenty-four motor vehicle accident victims admitted by the trauma team at the Royal Adelaide Hospital. A 52% response rate was achieved. Post-traumatic stress disorder as diagnosed by the Diagnostic Interview Schedule and disability as measured with the Sickness Impact Profile. Eighteen months after their accidents, six of the 24 subjects had clinically significant PTSD and one was considered borderline. None had been previously diagnosed or treated. The group with PTSD had higher scores on all measures of psychological distress one month after the accident and were more likely to use immature psychological defences. There was no association between physical outcome (measured with the modified Glasgow Outcome Scale) at six months and subsequent diagnosis of PTSD. However, the group with PTSD had higher levels of disability on assessment with the Sickness Impact Profile, particularly in the domain of social functioning. The results suggest PTSD was associated with work-related dysfunction equal to that associated with severe physical handicap. The data from this pilot study suggest that PTSD after motor vehicle accidents is an important cause of disability, which may also become the focus for damages in litigation. Thus, there is a need for further investigation of the early patterns of distress and to design preventive programs for victims of road accidents.

Sleep deficiency and motor vehicle crash risk in the general population: a prospective cohort study.

Science.gov (United States)

Gottlieb, Daniel J; Ellenbogen, Jeffrey M; Bianchi, Matt T; Czeisler, Charles A

2018-03-20

Insufficient sleep duration and obstructive sleep apnea, two common causes of sleep deficiency in adults, can result in excessive sleepiness, a well-recognized cause of motor vehicle crashes, although their contribution to crash risk in the general population remains uncertain. The objective of this study was to evaluate the relation of sleep apnea, sleep duration, and excessive sleepiness to crash risk in a community-dwelling population. This was a prospective observational cohort study nested within the Sleep Heart Health Study, a community-based study of the health consequences of sleep apnea. The participants were 1745 men and 1456 women aged 40-89 years. Sleep apnea was measured by home polysomnography and questionnaires were used to assess usual sleep duration and daytime sleepiness. A follow-up questionnaire 2 years after baseline ascertained driving habits and motor vehicle crash history. Logistic regression analysis was used to examine the relation of sleep apnea and sleep duration at baseline to the occurrence of motor vehicle crashes during the year preceding the follow-up visit, adjusting for relevant covariates. The population-attributable fraction of motor vehicle crashes was estimated from the sample proportion of motor vehicle crashes and the adjusted odds ratios for motor vehicle crash within each exposure category. Among 3201 evaluable participants, 222 (6.9%) reported at least one motor vehicle crash during the prior year. A higher apnea-hypopnea index (p vehicle crashes was 10% due to sleep apnea and 9% due to sleep duration less than 7 hours. Sleep deficiency due to either sleep apnea or insufficient sleep duration is strongly associated with motor vehicle crashes in the general population, independent of self-reported excessive sleepiness.

9 CFR 3.15 - Primary conveyances (motor vehicle, rail, air, and marine).

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Primary conveyances (motor vehicle, rail, air, and marine). 3.15 Section 3.15 Animals and Animal Products ANIMAL AND PLANT HEALTH... conveyances (motor vehicle, rail, air, and marine). (a) The animal cargo space of primary conveyances used to...

9 CFR 3.138 - Primary conveyances (motor vehicle, rail, air, and marine).

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Primary conveyances (motor vehicle, rail, air, and marine). 3.138 Section 3.138 Animals and Animal Products ANIMAL AND PLANT HEALTH... (motor vehicle, rail, air, and marine). (a) The animal cargo space of primary conveyances used in...

9 CFR 3.88 - Primary conveyances (motor vehicle, rail, air, and marine).

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Primary conveyances (motor vehicle, rail, air, and marine). 3.88 Section 3.88 Animals and Animal Products ANIMAL AND PLANT HEALTH... conveyances (motor vehicle, rail, air, and marine). (a) The animal cargo space of primary conveyances used to...

9 CFR 3.62 - Primary conveyances (motor vehicle, rail, air, and marine).

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Primary conveyances (motor vehicle, rail, air, and marine). 3.62 Section 3.62 Animals and Animal Products ANIMAL AND PLANT HEALTH... (motor vehicle, rail, air, and marine). (a) The animal cargo space of primary conveyances used in...

9 CFR 3.37 - Primary conveyances (motor vehicle, rail, air, and marine).

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Primary conveyances (motor vehicle, rail, air, and marine). 3.37 Section 3.37 Animals and Animal Products ANIMAL AND PLANT HEALTH... conveyances (motor vehicle, rail, air, and marine). (a) The animal cargo space of primary conveyances used in...

Motor vehicles and internal combustion engines; Kraftfahrwesen und Verbrennungsmotoren

Energy Technology Data Exchange (ETDEWEB)

Bargende, M.; Wiedemann, J. [eds.

1999-07-01

The book comprises the papers presented at the 3rd Stuttgart symposium. It reviews the state of the art in science and engineering and outlines future perspectives in the fields of motor vehicles and internal combustion engines. As the conference, the book comprises three sections: 'Engines' on DI spark ignition engines and diesel engines, mixing, combustion and exhaust purification. 'Motor cars' discusses acoustics and aeroacoustics, aerodynamics and wind tunnel technology, comfort, driving gear and stability control. 'Motor vehicle systems' contains papers on thermomanagement, control and automation, real-time applications in motor car simulation, software tools in the control systems development process, and simulation in motor vehicle systems development. Finally, the plenary paper 'Fuel cells, a solution for non-polluting motor car drives' by Dr.-Ing. F. Panik is also contained in the book. [German] Das vorliegende Buch enthaelt die Vortraege des 3. Stuttgarter Symposiums. Es gibt einen Ueberblick ueber den aktuellen Stand von Wissenschaft und Technik und zeigt zukuenftige Perspektiven im Bereich Kraftfahrwesen und Verbrennungsmotoren. Entsprechend der Tagung gliedert sich das Buch in drei Teile. Teil 1 'Motoren' besteht aus Vortraegen ueber Ottomotoren mit Direkteinspritzung und Dieselmotoren, Gemischbildung, Verbrennung und Abgasnachbehandlung, Analyse, Simulation und Motorkomponenten. Teil 2 'Kraftfahrzeuge' enthaelt Arbeiten ueber Fahrzeugakustik und Aeroakustik, Fahrzeug-Aerodynamik und Windkanaltechnik, Fahrzeugkomfort, Fahrwerk und Fahrdynamik. Teil 3 'Kraftfahrzeugsystemtechnik' enthaelt Beitraege ueber Thermomanagement, Regelungs- und Automatisierungstechnik, Echtzeitanwendungen in der Kfz-Simulationstechnik, Softwaretools im Steuergeraete-Entwicklungsprozess und Simulation in der Kraftfahrzeug-Systementwicklung. Der abschliessende Plenarvortrag des Symposiums &apos

A primer on motor vehicle air pollution.

Science.gov (United States)

1973-01-01

This primer presents a brief state-of-the art review of motor vehicle air pollution. Its purpose is to aid highway personnel in understanding the nature of this environmental problem on our highways and to present possible solutions for its abatement...

A lightweight electronically commutated dc motor for electric passenger vehicles

Science.gov (United States)

Echolds, E. F.; Walla, P. S.

1982-01-01

A functional model breadboard converter and a rare-earth-cobalt, permanent magnet motor; as well as an engineering model converter and PM motor suitable for vehicle installations were developed and tested. The converter and motor achieved an 88% peak efficiency, a maximum output of 26 kW at 26,000 rpm, and a continuous rating of 15 kW. The system also generated power to the source during braking, with a demonstrated peak power available at the converter terminals of approximately 26 kW at 88% efficiency. Major conclusions include: (1) the SAE J227a(D) driving cycle efficiency for the converter/motor is 86% to 88% when energy available for recovery at the converter terminals is included; (2) the converter initial cost is approximately five times that of the permanent magnet motor, but can be reduced by means of LSI logic and integrated liquid cooled semiconductor packages; and (3) an electronically commutated motor with a liquid cooled converter will operate reliably without service or maintenance for the life of a passenger vehicle.

A lightweight electronically commutated dc motor for electric passenger vehicles

Science.gov (United States)

Echolds, E. F.; Walla, P. S.

1982-09-01

A functional model breadboard converter and a rare-earth-cobalt, permanent magnet motor; as well as an engineering model converter and PM motor suitable for vehicle installations were developed and tested. The converter and motor achieved an 88% peak efficiency, a maximum output of 26 kW at 26,000 rpm, and a continuous rating of 15 kW. The system also generated power to the source during braking, with a demonstrated peak power available at the converter terminals of approximately 26 kW at 88% efficiency. Major conclusions include: (1) the SAE J227a(D) driving cycle efficiency for the converter/motor is 86% to 88% when energy available for recovery at the converter terminals is included; (2) the converter initial cost is approximately five times that of the permanent magnet motor, but can be reduced by means of LSI logic and integrated liquid cooled semiconductor packages; and (3) an electronically commutated motor with a liquid cooled converter will operate reliably without service or maintenance for the life of a passenger vehicle.

Real-world adjustments of driver seat and head restraint in Saab 9-3 vehicles.

Science.gov (United States)

Carlsson, Anna; Pipkorn, Linda; Kullgren, Anders; Svensson, Mats

2017-05-19

Whiplash-associated disorder (WAD), commonly denoted whiplash injury, is a worldwide problem. These injuries occur at relatively low changes of velocity (typically whiplash injury than males.  Improved seat design is the prevailing means of increasing the protection of whiplash injury for occupants in rear impacts. Since 1997, more advanced whiplash protection systems have been introduced on the market, the Saab Active Head Restraint (SAHR) being one of the most prominent. The SAHR-which is height adjustable-is mounted to a pressure plate in the seatback by means of a spring-resisted link mechanism.  Nevertheless, studies have shown that seats equipped with reactive head restraints (such as the SAHR) have a very high injury-reducing effect for males (∼60-70%) but very low or no reduction effect for females. One influencing factor could be the position of the head restraint relative to the head, because a number of studies have reported that adjustable head restraints often are incorrectly positioned by drivers.  The aim was to investigate how female and male Saab drivers adjust the seat in the car they drive the most. The seated positions of drivers in stationary conditions have been investigated in a total of 76 volunteers (34 females, 42 males) who participated in the study. Inclusion criteria incorporated driving a Saab 9-3 on a regularly basis. The majority of the volunteers (89%) adjusted the head restraint to any of the 3 uppermost positions and as many as 59% in the top position.  The average vertical distance between the top of the head and the top of the head restraint (offset) increase linearly with increasing statures, from an average of -26 mm (head below the head restraint) for small females to an average of 82 mm (head above the head restraint) for large males. On average, the offset was 23 mm for females, which is within a satisfactory range and in accordance with recommendations; the corresponding value for males was 72 mm. �

Hybrid Turbine Electric Vehicle

Science.gov (United States)

Viterna, Larry A.

1997-01-01

Hybrid electric power trains may revolutionize today's ground passenger vehicles by significantly improving fuel economy and decreasing emissions. The NASA Lewis Research Center is working with industry, universities, and Government to develop and demonstrate a hybrid electric vehicle. Our partners include Bowling Green State University, the Cleveland Regional Transit Authority, Lincoln Electric Motor Division, the State of Ohio's Department of Development, and Teledyne Ryan Aeronautical. The vehicle will be a heavy class urban transit bus offering double the fuel economy of today's buses and emissions that are reduced to 1/10th of the Environmental Protection Agency's standards. At the heart of the vehicle's drive train is a natural-gas-fueled engine. Initially, a small automotive engine will be tested as a baseline. This will be followed by the introduction of an advanced gas turbine developed from an aircraft jet engine. The engine turns a high-speed generator, producing electricity. Power from both the generator and an onboard energy storage system is then provided to a variable-speed electric motor attached to the rear drive axle. An intelligent power-control system determines the most efficient operation of the engine and energy storage system.

40 CFR 80.552 - What compliance options are available to motor vehicle diesel fuel small refiners?

Science.gov (United States)

2010-07-01

... to motor vehicle diesel fuel small refiners? 80.552 Section 80.552 Protection of Environment... Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Small Refiner Hardship Provisions § 80.552 What compliance options are available to motor vehicle diesel fuel...

Propulsion Wheel Motor for an Electric Vehicle

Science.gov (United States)

Figuered, Joshua M. (Inventor); Herrera, Eduardo (Inventor); Waligora, Thomas M. (Inventor); Bluethmann, William J. (Inventor); Farrell, Logan Christopher (Inventor); Lee, Chunhao J. (Inventor); Vitale, Robert L. (Inventor); Winn, Ross Briant (Inventor); Eggleston, IV, Raymond Edward (Inventor); Guo, Raymond (Inventor);

Child seat belt guidelines: Examining the 4 feet 9 inches rule as the standard.

Science.gov (United States)

Morse, Amber M; Aitken, Mary E; Mullins, Samantha H; Miller, Beverly K; Pomtree, Mindy M; Ulloa, Erin M; Montgomery, Jeffrey S; Saylors, Marie E

2017-08-01

Current American Academy of Pediatrics recommendations regarding transition from child safety/booster seat to adult safety belt use indicate that children should be at least 4 feet 9 inches, 8 years old, or 80 pounds. Proper fit in the vehicle seat, assessed with a five-point fit test, should also be met. Although most children reach 4 feet 9 inches around age 8 years, each child and vehicle presents a unique combination; thus a child may not fit appropriately in all vehicle types using only the 4 feet 9 inches requirement. We enrolled children, aged 7 years to 12 years, into our study. Height, weight, and demographic data were obtained. A Child Passenger Safety Technician then performed the five-point fit test in each of a uniform lineup of five vehicles. Data were collected on fit in the standard vehicle seat and also in a booster seat. We set 90% as the threshold proportion of children who meet all criteria for proper fit to validate current recommendations of a height of 4 feet 9 inches. Data were collected on 388 children. The percentage of 90% proper fit was met in the compact car and small sport-utility vehicle (SUV). However, only 80 (77%) of 104 students (p vehicles (large SUVs and trucks). This emphasizes the need for evaluation of fit by a trained personnel and/or development of standard back seat dimensions in all vehicles for maximum safety. Epidemiologic study, level III; Therapeutic study, level V.

Evaluation of half wave induction motor drive for use in passenger vehicles

Science.gov (United States)

Hoft, R. G.; Kawamura, A.; Goodarzi, A.; Yang, G. Q.; Erickson, C. L.

1985-01-01

Research performed at the University of Missouri-Columbia to devise and design a lower cost inverter induction motor drive for electrical propulsion of passenger vehicles is described. A two phase inverter motor system is recommended. The new design is predicted to provide comparable vehicle performance, improved reliability and a cost advantage for a high production vehicle, decreased total rating of the power semiconductor switches, and a somewhat simpler control hardware compared to the conventional three phase bridge inverter motor drive system. The major disadvantages of the two phase inverter motor drive are that it is larger and more expensive than a three phase machine, the design of snubbers for the power leakage inductances produce higher transient voltages, and the torque pulsations are relatively large because of the necessity to limit the inverter switching frequency to achieve high efficiency.

40 CFR 80.594 - What are the pre-compliance reporting requirements for motor vehicle diesel fuel?

Science.gov (United States)

2010-07-01

... requirements for motor vehicle diesel fuel? 80.594 Section 80.594 Protection of Environment ENVIRONMENTAL... Requirements § 80.594 What are the pre-compliance reporting requirements for motor vehicle diesel fuel? (a... June 1, 2005, all refiners and importers planning to produce or import motor vehicle diesel fuel...

40 CFR 80.520 - What are the standards and dye requirements for motor vehicle diesel fuel?

Science.gov (United States)

2010-07-01

... requirements for motor vehicle diesel fuel? 80.520 Section 80.520 Protection of Environment ENVIRONMENTAL... Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Motor Vehicle Diesel Fuel Standards and Requirements § 80.520 What are the standards and dye requirements for motor vehicle diesel...

Impact of reformulated fuels on motor vehicle emissions

Science.gov (United States)

Kirchstetter, Thomas

Motor vehicles continue to be an important source of air pollution. Increased vehicle travel and degradation of emission control systems have offset some of the effects of increasingly stringent emission standards and use of control technologies. A relatively new air pollution control strategy is the reformulation of motor vehicle fuels, both gasoline and diesel, to make them cleaner- burning. Field experiments in a heavily traveled northern California roadway tunnel revealed that use of oxygenated gasoline reduced on-road emissions of carbon monoxide (CO) and volatile organic compounds (VOC) by 23 +/- 6% and 19 +/- 8%, respectively, while oxides of nitrogen (NOx) emissions were not significantly affected. The introduction of reformulated gasoline (RFG) in California led to large changes in gasoline composition including decreases in alkene, aromatic, benzene, and sulfur contents, and an increase in oxygen content. The combined effects of RFG and fleet turnover between summers 1994 and 1997 were decreases in on-road vehicle exhaust emissions of CO, non-methane VOC, and NOx by 31 +/- 5, 43 +/- 8, and 18 +/- 4%, respectively. Although it was difficult to separate the fleet turnover and RFG contributions to these changes, it was clear that the effect of RFG was greater for VOC than for NOx. The RFG effect on exhaust emissions of benzene was a 30-40% reduction. Use of RFG reduced the reactivity of liquid gasoline and gasoline headspace vapors by 23 and 19%, respectively. Increased use of methyl tert-butyl ether in gasoline led to increased concentrations of highly reactive formaldehyde and isobutene in vehicle exhaust. As a result, RFG reduced the reactivity of exhaust emissions by only about 5%. Per unit mass of fuel burned, heavy-duty diesel trucks emit about 25 times more fine particle mass and 15-20 times the number of fine particles compared to light-duty vehicles. Exhaust fine particle emissions from heavy-duty diesels contain more black carbon than particulate

Validation of a motor activity system by a robotically controlled vehicle and using standard reference compounds.

Science.gov (United States)

Patterson, John P; Markgraf, Carrie G; Cirino, Maria; Bass, Alan S

2005-01-01

A series of experiments were undertaken to evaluate the accuracy, precision, specificity, and sensitivity of an automated, infrared photo beam-based open field motor activity system, the MotorMonitor v. 4.01, Hamilton-Kinder, LLC, for use in a good laboratory practices (GLP) Safety Pharmacology laboratory. This evaluation consisted of two phases: (1) system validation, employing known inputs using the EM-100 Controller Photo Beam Validation System, a robotically controlled vehicle representing a rodent and (2) biologic validation, employing groups of rats treated with the standard pharmacologic agents diazepam or D-amphetamine. The MotorMonitor's parameters that described the open-field activity of a subject were: basic movements, total distance, fine movements, x/y horizontal ambulations, rearing, and total rest time. These measurements were evaluated over a number of zones within each enclosure. System validation with the EM-100 Controller Photo Beam Validation System showed that all the parameters accurately and precisely measured what they were intended to measure, with the exception of fine movements and x/y ambulations. Biologic validation using the central nervous system depressant diazepam at 1, 2, or 5 mg/kg, i.p. produced the expected dose-dependent reduction in rat motor activity. In contrast, the central nervous system stimulant D-amphetamine produced the expected increases in rat motor activity at 0.1 and 1 mg/kg, i.p, demonstrating the specificity and sensitivity of the system. Taken together, these studies of the accuracy, precision, specificity, and sensitivity show the importance of both system and biologic validation in the evaluation of an automated open field motor activity system for use in a GLP compliant laboratory.

77 FR 20486 - Petition for Exemption From the Vehicle Theft Prevention Standard; Mitsubishi Motors

Science.gov (United States)

2012-04-04

... From the Vehicle Theft Prevention Standard; Mitsubishi Motors AGENCY: National Highway Traffic Safety... exemption of the Mitsubishi i-MiEV vehicle line in accordance with 49 CFR part 543, Exemption From the Theft... motor vehicle theft as compliance with the parts-marking requirements of the 49 CFR part 541, Federal...

Motor Vehicle Crash Deaths PSA (:60)

Centers for Disease Control (CDC) Podcasts

This 60 second public service announcement is based on the July 2016 CDC Vital Signs report. In the U.S., about 90 people die in motor vehicle crashes each day and thousands more are injured, resulting in hundreds of millions of dollars in direct medical costs each year. Learn what you can do to stay safe.

76 FR 5248 - Insurer Reporting Requirements; Annual Insurer Report on Motor Vehicle Theft for the 2005...

Science.gov (United States)

2011-01-28

...] Insurer Reporting Requirements; Annual Insurer Report on Motor Vehicle Theft for the 2005 Reporting Year... on motor vehicle theft for the 2005 reporting year. Section 33112(h) of Title 49 of the U.S. Code... report provides information on theft and recovery of vehicles; rating rules and plans used by motor...

Systematic review of military motor vehicle crash-related injuries.

Science.gov (United States)

Krahl, Pamela L; Jankosky, Christopher J; Thomas, Richard J; Hooper, Tomoko I

2010-01-01

Motor vehicle crashes account for nearly one third of U.S. military fatalities annually. The objective of this review is to summarize the published evidence on injuries due specifically to military motor vehicle (MMV) crashes. A search of 18 electronic databases identified English language publications addressing MMV crash-related injuries between 1970 and 2006 that were available to the general public. Documents limited in distribution to military or government personnel were not evaluated. Relevant articles were categorized by study design. The search identified only 13 studies related specifically to MMV crashes. Most were case reports or case series (n=8); only one could be classified as an intervention study. Nine of the studies were based solely on data from service-specific military safety centers. Few studies exist on injuries resulting from crashes of military motor vehicles. Epidemiologic studies that assess injury rates, type, severity, and risk factors are needed, followed by studies to evaluate targeted interventions and prevention strategies. Interventions currently underway should be evaluated for effectiveness, and those proven effective in the civilian community, such as graduated driver licensing, should be considered for implementation and evaluation in military populations. Published by Elsevier Inc.

National Motor Vehicle Crash Causation Survey (NMVCCS) - NMVCCS XML Case Viewer

Data.gov (United States)

Department of Transportation — The National Motor Vehicle Crash Causation Survey (NMVVCS) was a nationwide survey of crashes involving light passenger vehicles, with a focus on the factors related...

Post traumatic stress disorder among motor vehicle accident ...

African Journals Online (AJOL)

PTSD) and associated risk factors among motor vehicle accident (MVA) survivors attending the orthopaedic and trauma clinic at Kenyatta National Hospital, Nairobi. Design: A cross-sectional study. Setting: Kenyatta National Hospital, Nairobi.

Motor vehicle fuel economy, the forgotten HC control stragegy. [Hydrocarbon (HC)

Energy Technology Data Exchange (ETDEWEB)

Deluchi, M.; Wang, Quanlu; Greene, D.L.

1992-06-01

Emissions of hydrocarbons from motor vehicles are recognized as major contributors to ozone pollution in urban areas. Petroleum-based motor fuels contain volatile organic compounds (VOC) which, together with oxides of nitrogen, promote the formation of ozone in the troposphere via complex photochemical reactions. VOC emissions from the tailpipe and evaporation from the fuel and engine systems of highway vehicles are believed to account for about 40% of total VOC emissions in any region. But motor fuels also generate emissions throughout the fuel cycle, from crude oil production to refining, storage, transportation, and handling, that can make significant contributions to the total inventory of VOC emissions. Many of these sources of emissions are directly related to the quantity of fuel produced and handled throughout the fuel cycle. It is, therefore, reasonable to expect that a reduction in total fuel throughput might result in a reduction of VOC emissions. In particular, reducing vehicle fuel consumption by increasing vehicle fuel economy should reduce total fuel throughput, thereby cutting total emissions of VOCS. In this report we identify the sources of VOC emissions throughout the motor fuel cycle, quantify them to the extent possible, and describe their dependence on automobile and light truck fuel economy.

Analysis of Wheel Hub Motor Drive Application in Electric Vehicles

Directory of Open Access Journals (Sweden)

Sun Yuechao

2017-01-01

Full Text Available Based on the comparative analysis of the performance characteristics of centralized and distributed drive electric vehicles, we found that the wheel hub motor drive mode of the electric vehicles with distributed drive have compact structure, high utilization ratio of interior vehicle space, lower center of vehicle gravity, good driving stability, easy intelligent control and many other advantages, hence in line with the new requirements for the development of drive performance of electric vehicles, and distributed drive will be the ultimate mode of electric vehicles in the future.

Motor Vehicle Safety (A Cup of Health with CDC)

Centers for Disease Control (CDC) Podcasts

2014-10-16

In our highly mobile society, travel in vehicles is an almost daily occurrence for most Americans. Every trip places us at risk for serious injury. In this podcast, Dr. Gwen discusses ways to avoid serious injuries in motor vehicles.  Created: 10/16/2014 by MMWR.   Date Released: 10/16/2014.

76 FR 2444 - Petition for Exemption From the Vehicle Theft Prevention Standard; Ford Motor Company

Science.gov (United States)

2011-01-13

... From the Vehicle Theft Prevention Standard; Ford Motor Company AGENCY: National Highway Traffic Safety... vehicle line in accordance with 49 CFR Part 543, Exemption from the Theft Prevention Standard. This... standard equipment is likely to be as effective in reducing and deterring motor vehicle theft as compliance...

77 FR 48105 - Federal Motor Vehicle Safety Standards; Motorcycle Helmets

Science.gov (United States)

2012-08-13

... [Docket No. NHTSA-2012-0112] Federal Motor Vehicle Safety Standards; Motorcycle Helmets AGENCY: National... Vehicle Safety Standard for motorcycle helmets. Specifically, the final rule amended the helmet labeling... compliance test procedures of FMVSS No. 218, Motorcycle helmets, in order to make it more difficult to...

40 CFR 80.583 - What alternative sampling and testing requirements apply to importers who transport motor vehicle...

Science.gov (United States)

2010-07-01

... requirements apply to importers who transport motor vehicle diesel fuel, NRLM diesel fuel, or ECA marine fuel... (CONTINUED) AIR PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel... alternative sampling and testing requirements apply to importers who transport motor vehicle diesel fuel, NRLM...

Kinetic energy recovery systems in motor vehicles

Science.gov (United States)

Śliwiński, C.

2016-09-01

The article draws attention to the increasing environmental pollution caused by the development of vehicle transport and motorization. Different types of design solutions used in vehicles for the reduction of fuel consumption, and thereby emission of toxic gasses into the atmosphere, were specified. Historical design solutions concerning energy recovery devices in mechanical vehicles which used flywheels to accumulate kinetic energy were shown. Developmental tendencies in the area of vehicle manufacturing in the form of hybrid electric and electric devices were discussed. Furthermore, designs of energy recovery devices with electrical energy storage from the vehicle braking and shock absorbing systems were presented. A mechanical energy storing device using a flywheel operating under vacuum was presented, as were advantages and disadvantages of both systems, the limitations they impose on individual constructions and safety issues. The paper also discusses a design concept of an energy recovery device in mechanical vehicles which uses torsion springs as the main components of energy accumulation during braking. The desirability of a cooperation of both the mechanical- and electrical energy recovery devices was indicated.

Auditory perception of motor vehicle travel paths.

Science.gov (United States)

Ashmead, Daniel H; Grantham, D Wesley; Maloff, Erin S; Hornsby, Benjamin; Nakamura, Takabun; Davis, Timothy J; Pampel, Faith; Rushing, Erin G

2012-06-01

These experiments address concerns that motor vehicles in electric engine mode are so quiet that they pose a risk to pedestrians, especially those with visual impairments. The "quiet car" issue has focused on hybrid and electric vehicles, although it also applies to internal combustion engine vehicles. Previous research has focused on detectability of vehicles, mostly in quiet settings. Instead, we focused on the functional ability to perceive vehicle motion paths. Participants judged whether simulated vehicles were traveling straight or turning, with emphasis on the impact of background traffic sound. In quiet, listeners made the straight-or-turn judgment soon enough in the vehicle's path to be useful for deciding whether to start crossing the street. This judgment is based largely on sound level cues rather than the spatial direction of the vehicle. With even moderate background traffic sound, the ability to tell straight from turn paths is severely compromised. The signal-to-noise ratio needed for the straight-or-turn judgment is much higher than that needed to detect a vehicle. Although a requirement for a minimum vehicle sound level might enhance detection of vehicles in quiet settings, it is unlikely that this requirement would contribute to pedestrian awareness of vehicle movements in typical traffic settings with many vehicles present. The findings are relevant to deliberations by government agencies and automobile manufacturers about standards for minimum automobile sounds and, more generally, for solutions to pedestrians' needs for information about traffic, especially for pedestrians with sensory impairments.

75 FR 60036 - Federal Motor Vehicle Safety Standards; New Pneumatic Tires for Motor Vehicles With a GVWR of...

Science.gov (United States)

2010-09-29

... evaluates resistance to heat buildup when the tire is run at stepped-up loads at or near its rated load... that involves a tire running on the roadwheel under specified conditions to allow for tire growth. The... [Docket No. NHTSA-2010-0132] RIN 2127-AK17 Federal Motor Vehicle Safety Standards; New Pneumatic Tires for...

Design and Research on Vehicles Motor Testing System Based on Improvement PID

Directory of Open Access Journals (Sweden)

Fan Kuangang

2014-08-01

Full Text Available Motor is the important parts in vehicles. It is the key parts for achieving automation. It is the critical technology to test vehicle motors. We take the PID (Proportion Integration Differentiation as based fundamental controlling algorithm, and we test motor parameters through LabVIEW for single-chip AT89C52. According to practical working condition, we build circuit electric field boundary, and analyze electric field distribution of hard circuit. In addition, we also design filtering circuit for main interrupt frequency (below 1 kHz, and we improved PID for direct motor speed which is controlled by PWM (pulse-width modulation to reach speed astatic regulation. At the same time, the system achieves soft start-up.

Implementation of Permanent Magnet Motors in Electric Vehicles

OpenAIRE

Elvestad, Eirik

2008-01-01

This thesis has studied permanent magnet motors in electric vehicles (EVs) under the assumption that they are tractable due to a low weight and high compactness. The implementation has been investigated through a case study, which resulted in an EV simulation model. The model contains a maximal torque per ampere and a closed-loop field weakening controller. Abstract Faults are a special concern in permanent magnet motors. Fault sources and faulted behavior are addressed separately. The EV mo...

Obstructive sleep apnea among commercial motor vehicle drivers: using evidence-based practice to identify risk factors.

Science.gov (United States)

Olszewski, Kimberly; Wolf, Debra

2013-11-01

Commercial motor vehicle driving is a hazardous occupation, having the third highest fatality rate among common U.S. jobs. Among the estimated 14 million U.S. commercial motor vehicle drivers, the prevalence of obstructive sleep apnea is reported to be 17% to 28%. Despite the identified increased prevalence of obstructive sleep apnea among commercial motor vehicle drivers, federal law does not require that they be screened for obstructive sleep apnea. This article presents an evidence-based practice change project; the authors developed, implemented, and evaluated a screening program to identify commercial motor vehicle drivers' risk for obstructive sleep apnea during commercial driver medical examinations. The results of this practice change indicated screening for obstructive sleep apnea during the commercial driver medical examination led to improved identification of obstructive sleep apnea risk among commercial motor vehicle drivers and should be a clinical standard in occupational health clinics. Copyright 2013, SLACK Incorporated.

Standardized error severity score (ESS) ratings to quantify risk associated with child restraint system (CRS) and booster seat misuse.

Science.gov (United States)

Rudin-Brown, Christina M; Kramer, Chelsea; Langerak, Robin; Scipione, Andrea; Kelsey, Shelley

2017-11-17

Although numerous research studies have reported high levels of error and misuse of child restraint systems (CRS) and booster seats in experimental and real-world scenarios, conclusions are limited because they provide little information regarding which installation issues pose the highest risk and thus should be targeted for change. Beneficial to legislating bodies and researchers alike would be a standardized, globally relevant assessment of the potential injury risk associated with more common forms of CRS and booster seat misuse, which could be applied with observed error frequency-for example, in car seat clinics or during prototype user testing-to better identify and characterize the installation issues of greatest risk to safety. A group of 8 leading world experts in CRS and injury biomechanics, who were members of an international child safety project, estimated the potential injury severity associated with common forms of CRS and booster seat misuse. These injury risk error severity score (ESS) ratings were compiled and compared to scores from previous research that had used a similar procedure but with fewer respondents. To illustrate their application, and as part of a larger study examining CRS and booster seat labeling requirements, the new standardized ESS ratings were applied to objective installation performance data from 26 adult participants who installed a convertible (rear- vs. forward-facing) CRS and booster seat in a vehicle, and a child test dummy in the CRS and booster seat, using labels that only just met minimal regulatory requirements. The outcome measure, the risk priority number (RPN), represented the composite scores of injury risk and observed installation error frequency. Variability within the sample of ESS ratings in the present study was smaller than that generated in previous studies, indicating better agreement among experts on what constituted injury risk. Application of the new standardized ESS ratings to installation

76 FR 72404 - Adequacy Status of Motor Vehicle Emissions Budgets in Submitted PM10

Science.gov (United States)

2011-11-23

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9495-4] Adequacy Status of Motor Vehicle Emissions Budgets in Submitted PM 10 Maintenance Plan for Sacramento County; CA AGENCY: Environmental Protection Agency (EPA... found that the motor vehicle emissions budgets (MVEBs) for particulate matter with an aerodynamic...

Explaining reduction of pedestrian-motor vehicle crashes in Arkhangelsk, Russia, in 2005-2010.

Science.gov (United States)

Kudryavtsev, Alexander V; Nilssen, Odd; Lund, Johan; Grjibovski, Andrej M; Ytterstad, Børge

2012-01-01

To explain a reduction in pedestrian-motor vehicle crashes in Arkhangelsk, Russia, in 2005-2010. Retrospective ecological study. For 2005-2010, police data on pedestrian-motor vehicle crashes, traffic violations, and total motor vehicles (MVs) were combined with data on changes in national road traffic legislation and municipal road infrastructure. Negative binomial regression was used to investigate trends in monthly rates of pedestrian-motor vehicle crashes per total MVs and estimate changes in these rates per unit changes in the safety measures. During the 6 years, the police registered 2,565 pedestrian-motor vehicle crashes: 1,597 (62%) outside crosswalks, 766 (30%) on non-signalized crosswalks, and 202 (8%) on signalized crosswalks. Crash rates outside crosswalks and on signalized crosswalks decreased on average by 1.1% per month, whereas the crash rate on non-signalized crosswalks remained unchanged. Numbers of signalized and non-signalized crosswalks increased by 14 and 19%, respectively. Also, 10% of non-signalized crosswalks were combined with speed humps, and 4% with light-reflecting vertical signs. Pedestrian penalties for traffic violations increased 4-fold. Driver penalties for ignoring prohibiting signal and failure to give way to pedestrian on non-signalized crosswalk increased 7- and 8-fold, respectively. The rate of total registered drivers' traffic violations per total MVs decreased on average by 0.3% per month. All studied infrastructure and legislative measures had inverse associations with the rate of crashes outside crosswalks. The rate of crashes on signalized crosswalks showed inverse associations with related monetary penalties. The introduction of infrastructure and legislative measures is the most probable explanation of the reduction of pedestrian-motor vehicle crashes in Arkhangelsk. The overall reduction is due to decreases in rates of crashes outside crosswalks and on signalized crosswalks. No change was observed in the rate of

Seat-belt use still low in Kuwait: self-reported driving behaviours among adult drivers.

Science.gov (United States)

Raman, Sudha R; Ottensmeyer, C Andrea; Landry, Michel D; Alfadhli, Jarrah; Procter, Steven; Jacob, Susan; Hamdan, Elham; Bouhaimed, Manal

2014-01-01

Kuwait mandated seat-belt use by drivers in 1976 and by front seat passengers in 1994. The study objectives were to identify and estimate current factors associated with seat-belt use and levels of potentially unsafe driving behaviours in Kuwait. In 2010, 741 adults were surveyed regarding driving habits and history. Only 41.6% of drivers reported always using a seat belt. Front seat passenger belt use was more common (30.5%) than rear seat belt use (6.5%). Distracted driving behaviours were common, including mobile phone use ('always' or 'almost always': 51.1%) and texting/SMS (32.4%). Logistic regression indicated that drivers who were young (18-19 years), male, Kuwaiti nationals or non-Kuwaiti Arabs, drove over the speed limit, had traffic violation tickets or >1 car crashes in the last year, were less likely to use seat belts. Targeted initiatives to increase public awareness and to enforce car-safety legislation, including use of seat belts, are necessary to decrease the health burden of car crashes in Kuwait.

Vision and commercial motor vehicle driver safety : vol. 1 : evidence report

Science.gov (United States)

2008-06-06

The purpose of this evidence report is to address several key questions posed by the Federal Motor Carrier Safety Administration (FMCSA) that pertain to vision and commercial motor vehicle (CMV) driver safety. Each of these key questions was develope...

Air change rates of motor vehicles and in-vehicle pollutant concentrations from secondhand smoke.

Science.gov (United States)

Ott, Wayne; Klepeis, Neil; Switzer, Paul

2008-05-01

The air change rates of motor vehicles are relevant to the sheltering effect from air pollutants entering from outside a vehicle and also to the interior concentrations from any sources inside its passenger compartment. We made more than 100 air change rate measurements on four motor vehicles under moving and stationary conditions; we also measured the carbon monoxide (CO) and fine particle (PM(2.5)) decay rates from 14 cigarettes smoked inside the vehicle. With the vehicle stationary and the fan off, the ventilation rate in air changes per hour (ACH) was less than 1 h(-1) with the windows closed and increased to 6.5 h(-1) with one window fully opened. The vehicle speed, window position, ventilation system, and air conditioner setting was found to affect the ACH. For closed windows and passive ventilation (fan off and no recirculation), the ACH was linearly related to the vehicle speed over the range from 15 to 72 mph (25 to 116 km h(-1)). With a vehicle moving, windows closed, and the ventilation system off (or the air conditioner set to AC Max), the ACH was less than 6.6 h(-1) for speeds ranging from 20 to 72 mph (32 to 116 km h(-1)). Opening a single window by 3'' (7.6 cm) increased the ACH by 8-16 times. For the 14 cigarettes smoked in vehicles, the deposition rate k and the air change rate a were correlated, following the equation k=1.3a (R(2)=82%; n=14). With recirculation on (or AC Max) and closed windows, the interior PM(2.5) concentration exceeded 2000 microg m(-3) momentarily for all cigarettes tested, regardless of speed. The concentration time series measured inside the vehicle followed the mathematical solutions of the indoor mass balance model, and the 24-h average personal exposure to PM(2.5) could exceed 35 microg m(-3) for just two cigarettes smoked inside the vehicle.

Training in the Motor Vehicle Repair and Sales Sector in Greece. Report for the FORCE Programme.

Science.gov (United States)

Papaionnou, Skevos; Patsatzis, N.

A study listed and analyzed the vocational training and continuing training systems for staff in the motor vehicle repair and sales sector in Greece. Heavy taxation on motor vehicles led to difficulty in replacing vehicles that resulted in a very high demand for vehicle repairs, which, in conjunction with the ambiguous legislation governing the…

40 CFR 80.593 - What are the reporting requirements for refiners and importers of motor vehicle diesel fuel...

Science.gov (United States)

2010-07-01

... for refiners and importers of motor vehicle diesel fuel subject to temporary refiner relief standards... PROGRAMS (CONTINUED) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive... the reporting requirements for refiners and importers of motor vehicle diesel fuel subject to...

Market Analysis and Consumer Impacts Source Document. Part I. The Motor Vehicle Market in the Late 1970's

Science.gov (United States)

1980-12-01

The source document on motor vehicle market analysis and consumer impact consists of three parts. Part I is an integrated overview of the motor vehicle market in the late 1970's, with sections on the structure of the market, motor vehicle trends, con...

Self-harm and risk of motor vehicle crashes among young drivers : findings from the DRIVE Study

NARCIS (Netherlands)

Martiniuk, Alexandra L. C.; Ivers, Rebecca Q.; Glozier, Nick; Patton, George C.; Lam, Lawrence T.; Boufous, Soufiane; Senserrick, Teresa; Williamson, Ann; Stevenson, Mark; Norton, Robyn

2009-01-01

Background: Some motor vehicle crashes, particularly single-vehicle crashes, may result from intentional self-harm. We conducted a prospective cohort study to assess the risk that intentional self-harm poses for motor vehicle crashes among young drivers. Methods: We prospectively linked survey data

Does knowledge of seat design and whiplash injury mechanisms translate to understanding outcomes?

Science.gov (United States)

Ivancic, Paul C

2011-12-01

Review of whiplash injury mechanisms and effects of anti-whiplash systems including active head restraint (AHR) and Whiplash Protection System (WHIPS). This article provides an overview of previous biomechanical and epidemiological studies of AHR and WHIPS and investigates whether seat design and biomechanical knowledge of proposed whiplash injury mechanisms translates to understanding outcomes of rear crash occupants. In attempt to reduce whiplash injuries, some newer automobiles incorporate anti-whiplash systems such as AHR or WHIPS. During a rear crash, mechanically based systems activate by occupant momentum pressing into the seatback whereas electronically based systems activate using crash sensors and an electronic control unit linked to the head restraint. To investigate the effects of AHR and WHIPS on occupant responses including head and neck loads and motions, biomechanical studies of simulated rear crashes have been performed using human volunteers, mathematical models, crash dummies, whole cadavers, and hybrid cadaveric/surrogate models. Epidemiological studies have evaluated the effects of AHR and WHIPS on reducing whiplash injury claims and lessening subjective complaints of neck pain after rear crashes. RESULTS.: Biomechanical studies indicate that AHR and WHIPS reduced the potential for some whiplash injuries but did not completely eliminate the injury risk. Epidemiological outcomes indicate reduced whiplash injury claims or subjective complaints of crash-related neck pain between 43 and 75% due to AHR and between 21% and 49% due to WHIPS as compared to conventional seats and head restraints. Yielding energy-absorbing seats aim to reduce occupant loads and accelerations whereas AHRs aim to provide early head support to minimize head and neck motions. Continued objective biomechanical and epidemiological studies of anti-whiplash systems together with industry, governmental, and clinical initiatives will ultimately lead to reduced whiplash injuries

Musculoskeletal analysis of driving fatigue: The influence of seat adjustments

DEFF Research Database (Denmark)

Majid, Noor Aliah binti Abdul; Abdullah, Mohd Fareez Edzuan; Jamaludin, Mohd Syahmi

2013-01-01

Main causes for discomfort experienced by vehicle drivers during driving were investigated using a rigid-body model originally developed in the AnyBody Modeling System [1]. The interactions between the human body and the car-seat in various combinations of seat-pan/backrest inclinations and the e...

Decoupling control of steering and driving system for in-wheel-motor-drive electric vehicle

Science.gov (United States)

Zhang, Han; Zhao, Wanzhong

2018-02-01

To improve the maneuverability and stability of in-wheel-motor-drive electric vehicle, a control strategy based on nonlinear decoupling control method is proposed in this paper, realizing the coordinated control of the steering and driving system. At first, the nonlinear models of the in-wheel-motor-drive electric vehicle and its sub-system are constructed. Then the inverse system decoupling theory is applied to decompose the nonlinear system into several independent subsystems, which makes it possible to realize the coordinated control of each subsystem. Next, the μ-Synthesis theory is applied to eliminate the influence of model uncertainty, improving the stability, robustness and tracking performance of in-wheel-motor-drive electric vehicle. Simulation and experiment results and numerical analyses, based on the electric vehicle actuated by in-wheel-motors, prove that the proposed control method is effective to accomplish the decoupling control of the steering and driving system in both simulation and real practice.

75 FR 6253 - Petition for Exemption From the Federal Motor Vehicle Theft Prevention Standard; Hyundia-Kia...

Science.gov (United States)

2010-02-08

... From the Federal Motor Vehicle Theft Prevention Standard; Hyundia-Kia America Technical Center, Inc..., Exemption from Vehicle Theft Prevention Standard. This petition is granted because the agency has determined... in reducing and deterring motor vehicle theft as compliance with the parts-marking requirements of 49...

Commercial Motor Vehicle Driving Safety Website

OpenAIRE

Tidwell, Scott; Trimble, Tammy; Blanco, Myra

2016-01-01

This report documents the CMV Driving Safety website (http://cmvdrivingsafety.org/), which was created by the National Surface Transportation Safety Center for Excellence (NSTSCE) as an outreach effort to assist commercial motor vehicle (CMV) fleets and drivers, driver trainers, CMV training schools, and insurance companies. The website contains 15 unique pages and provides six downloadable training modules on driver distraction, driver health, hours of service, driver drowsiness and fatigue,...

Time trend of polycyclic aromatic hydrocarbon emission factors from motor vehicles

Science.gov (United States)

Tao, Shu; Shen, Huizhong; Wang, Rong; Sun, Kang

2010-05-01

Motor vehicle is an important emission source of polycyclic aromatic hydrocarbons (PAHs) and this is particularly true in urban areas. Motor vehicle emission factors (EFs) for individual PAH compound reported in the literature varied for 4 to 5 orders of magnitude, leading to high uncertainty in emission estimation. In this study, the major factors affecting EFs were investigated and characterized by regression models. Based on the model developed, a motor vehicle PAH emission inventory at country level was developed. It was found that country and model year are the most important factors affecting EFs for PAHs. The influence of the two factors can be quantified by a single parameter of per capita gross domestic production (purchasing power parity), which was used as the independent variables of the regression models. The models developed using randomly selected 80% of measurements and tested with the remained data accounted for 28 to 48% of the variations in EFs for PAHs measured in 16 countries over 50 years. The regression coefficients of the EF prediction models were molecular weight dependent. Motor vehicle emission of PAHs from individual countries in the world in 1985, 1995, 2005, 2015, and 2025 were calculated and the global emission of total PAHs were 470, 390, and 430 Gg in 1985, 1995, and 2005 and will be 290 and 130 Gg in 2015 and 2025, respectively. The emission is currently passing its peak and will decrease due to significant decrease in China and other developing countries.

Cyclic Parameter Refinement of 4S-10 Hybrid Flux-Switching Motor for Lightweight Electric Vehicle

Science.gov (United States)

Rani, J. Abd; Sulaiman, E.; Kumar, R.

2017-08-01

A great deal of attention has been given to the reduction of lighting the vehicle because the lighter the vehicle the energy consumption is comparatively low. Hence, the lightweight electric vehicle was introduced for lower carbon footprint and the sizing of the vehicle itself. One of the components to reduce the weight of the vehicle is the propulsion system which comprised of electric motor functioning as the source of torque to drive the propulsion system of the machine. This paper presents the refinement methodology for the optimized design of the 4S-10P E-Core hybrid excitation flux switching motor. The purpose of the refinement methodology is to improve the torque production of the optimized motor. The result of the successful improvement of the torque production is justifiable for a lightweight electric vehicle to drive the propulsion system.

36 CFR 293.6 - Commercial enterprises, roads, motor vehicles, motorized equipment, motorboats, aircraft...

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Commercial enterprises, roads..., DEPARTMENT OF AGRICULTURE WILDERNESS-PRIMITIVE AREAS § 293.6 Commercial enterprises, roads, motor vehicles... National Forest Wilderness no commercial enterprises; no temporary or permanent roads; no aircraft landing...

78 FR 67213 - Petition for Exemption From the Federal Motor Vehicle Theft Prevention Standard; Porsche Cars...

Science.gov (United States)

2013-11-08

... From the Federal Motor Vehicle Theft Prevention Standard; Porsche Cars North America, Inc. AGENCY... From Vehicle Theft Prevention Standard. This petition is granted because the agency has determined that... reducing and deterring motor vehicle theft as compliance with the parts-marking requirements of the 49 CFR...

78 FR 21850 - Federal Motor Vehicle Safety Standards; Matters Incorporated by Reference

Science.gov (United States)

2013-04-12

... to the 1985 Annual Book of ASTM Standards, Vol. 05.04, ``Test Methods for Rating Motor, Diesel... for Rating Motor, Diesel, Aviation Fuels, A2. Reference Materials and Blending Accessories, (``ASTM... [Docket No. NHTSA-2011-0185] RIN 2127-AL25 Federal Motor Vehicle Safety Standards; Matters Incorporated by...

Universal Safety Distance Alert Device for Road Vehicles

Directory of Open Access Journals (Sweden)

Matic Virant

2016-04-01

Full Text Available Driving with too short of a safety distance is a common problem in road traffic, often with traffic accidents as a consequence. Research has identified a lack of vehicle-mountable devices for alerting the drivers of trailing vehicles about keeping a sufficient safe distance. The principal requirements for such a device were defined. A conceptual study was performed in order to select the components for the integration of the device. Based on the results of this study, a working prototype of a flexible, self-contained device was designed, built and tested. The device is intended to be mounted on the rear of a vehicle. It uses radar as the primary distance sensor, assisted with a GPS receiver for velocity measurement. A Raspberry Pi single-board computer is used for data acquisition and processing. The alerts are shown on an LED-matrix display mounted on the rear of the host vehicle. The device software is written in Python and provides automatic operation without requiring any user intervention. The tests have shown that the device is usable on almost any motor vehicle and performs reliably in simulated and real traffic. The open issues and possibilities for future improvements are presented in the Discussion.

Research on the Method of Setting Waiting Area for Non-motor Vehicle at Signal Control Intersection

Directory of Open Access Journals (Sweden)

Wang Yun Xia

2018-01-01

Full Text Available Electric bicycle has become an indispensable important component of the transportation system. The fact is that traffic organization and channelizing design of signal control intersection is not intensive, which cannot adapt to the current traffic demand of non-motor vehicle, such as unclear traffic rules and poor visibility, thus the traffic safety of non-motor vehicle is not optimistic. Therefore, it is necessary to study on traffic organization method based on the demand of non-motor vehicle, which can provide certain theoretical basis for traffic administrative department to make policy and traffic design. This article focuses on the method of setting waiting area for non-motor vehicle at signal control intersection, including the advantages, disadvantages and the applicable conditions.

Performance Analysis of Permanent Magnet Motors for Electric Vehicles (EV Traction Considering Driving Cycles

Directory of Open Access Journals (Sweden)

Thanh Anh Huynh

2018-05-01

Full Text Available This paper evaluates the electromagnetic and thermal performance of several traction motors for electric vehicles (EVs. Two different driving cycles are employed for the evaluation of the motors, one for urban and the other for highway driving. The electromagnetic performance to be assessed includes maximum motor torque output for vehicle acceleration and the flux weakening capability for wide operating range under current and voltage limits. Thermal analysis is performed to evaluate the health status of the magnets and windings for the prescribed driving cycles. Two types of traction motors are investigated: two interior permanent magnet motors and one permanent magnet-assisted synchronous reluctance motor. The analysis results demonstrate the benefits and disadvantages of these motors for EV traction and provide suggestions for traction motor design. Finally, experiments are conducted to validate the analysis.

a Study on the Mechanism of OCCUPANT'S Cervical Injury by Low Speed Rear-End Collision of Automobiles

Science.gov (United States)

Cho, Wonhak; Kim, Yongchul; Choi, Hyeonki

Neck injury in rear-end car collisions is an increasing concern in the field of traffic safety. This injury commonly occurs at rear-end impact, however the injury mechanisms for whiplash remain a mystery. The purpose of this study is to quantitatively analyze the head and neck kinematics during the low-speed rear-end impact of automobiles. It is important to produce data that is related as closely as possible to the in vivo situation. So, we performed a sled test which simulated rear-end impacts with a velocity of 0.6 m/s with five normal healthy male subjects. 3-D motion analysis system was used to document motion data of two situations. When we compare the values of angular velocity and acceleration of head and neck, the peak magnitudes of inclined seated posture were smaller than those of upright seated posture. The result of this study is expected to provide insight that will aid in determining the mechanism of whiplash which is crucial to the identification of possible injury mechanisms.

Series hybrid vehicle system analysis using an in-wheel motor design

NARCIS (Netherlands)

Paulides, J.J.H.; Kazmin, Evgeny; Gysen, B.L.J.; Lomonova, E.

2008-01-01

Hybrid vehicles, which employ a technology combining gasoline and electric motors, are a hot item these days for transporters looking for ways to cut their fuel bills. To date, commercial systems implement diesel assisted electrical drives. As such the electrical motor is placed in a series or

41 CFR 101-39.203-1 - Obtaining motor vehicles while on temporary duty (TDY) travel.

Science.gov (United States)

2010-07-01

... Management Federal Property Management Regulations System FEDERAL PROPERTY MANAGEMENT REGULATIONS AVIATION, TRANSPORTATION, AND MOTOR VEHICLES 39-INTERAGENCY FLEET MANAGEMENT SYSTEMS 39.2-GSA Interagency Fleet Management... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Obtaining motor vehicles...

Conversion of Hazardous Motor Vehicle Used Tire and Polystyrene Waste Plastic Mixture into useful Chemical Products

OpenAIRE

Moinuddin Sarker; Mohammad Mamunor Rashid

2014-01-01

Motor vehicle used tire and polystyrene waste plastic mixture into fuel recovery using thermal degradation process in laboratory batch process. Motor vehicle used tire and polystyrene waste plastic was use 75 gm by weight. Motor vehicle tire was 25 gm and polystyrene waste plastic was 50 gm. In presence of oxygen experiment was performed under laboratory fume hood. Thermal degradation temperature range was 100 - 420 oC and experiment run time was 5 hours. Product fuel density is 0.84 gm/ml an...

The Influence of Tractor-Seat Height above the Ground on Lateral Vibrations

Directory of Open Access Journals (Sweden)

Jaime Gomez-Gil

2014-10-01

Full Text Available Farmers experience whole-body vibrations when they drive tractors. Among the various factors that influence the vibrations to which the driver is exposed are terrain roughness, tractor speed, tire type and pressure, rear axle width, and tractor seat height above the ground. In this paper the influence of tractor seat height above the ground on the lateral vibrations to which the tractor driver is exposed is studied by means of a geometrical and an experimental analysis. Both analyses show that: (i lateral vibrations experienced by a tractor driver increase linearly with tractor-seat height above the ground; (ii lateral vibrations to which the tractor driver is exposed can equal or exceed vertical vibrations; (iii in medium-size tractors, a feasible 30 cm reduction in the height of the tractor seat, which represents only 15% of its current height, will reduce the lateral vibrations by around 20%; and (iv vertical vibrations are scarcely influenced by tractor-seat height above the ground. The results suggest that manufacturers could increase the comfort of tractors by lowering tractor-seat height above the ground, which will reduce lateral vibrations.

Research on motor rotational speed measurement in regenerative braking system of electric vehicle

Science.gov (United States)

Pan, Chaofeng; Chen, Liao; Chen, Long; Jiang, Haobin; Li, Zhongxing; Wang, Shaohua

2016-01-01

Rotational speed signals acquisition and processing techniques are widely used in rotational machinery. In order to realized precise and real-time control of motor drive and regenerative braking process, rotational speed measurement techniques are needed in electric vehicles. Obtaining accurate motor rotational speed signal will contribute to the regenerative braking force control steadily and realized higher energy recovery rate. This paper aims to develop a method that provides instantaneous speed information in the form of motor rotation. It addresses principles of motor rotational speed measurement in the regenerative braking systems of electric vehicle firstly. The paper then presents ideal and actual Hall position sensor signals characteristics, the relation between the motor rotational speed and the Hall position sensor signals is revealed. Finally, Hall position sensor signals conditioning and processing circuit and program for motor rotational speed measurement have been carried out based on measurement error analysis.

Predicting severe injury using vehicle telemetry data.

Science.gov (United States)

Ayoung-Chee, Patricia; Mack, Christopher D; Kaufman, Robert; Bulger, Eileen

2013-01-01

In 2010, the National Highway Traffic Safety Administration standardized collision data collected by event data recorders, which may help determine appropriate emergency medical service (EMS) response. Previous models (e.g., General Motors ) predict severe injury (Injury Severity Score [ISS] > 15) using occupant demographics and collision data. Occupant information is not automatically available, and 12% of calls from advanced automatic collision notification providers are unanswered. To better inform EMS triage, our goal was to create a predictive model only using vehicle collision data. Using the National Automotive Sampling System Crashworthiness Data System data set, we included front-seat occupants in late-model vehicles (2000 and later) in nonrollover and rollover crashes in years 2000 to 2010. Telematic (change in velocity, direction of force, seat belt use, vehicle type and curb weight, as well as multiple impact) and nontelematic variables (maximum intrusion, narrow impact, and passenger ejection) were included. Missing data were multiply imputed. The University of Washington model was tested to predict severe injury before application of guidelines (Step 0) and for occupants who did not meet Steps 1 and 2 criteria (Step 3) of the Centers for Disease Control and Prevention Field Triage Guidelines. A probability threshold of 20% was chosen in accordance with Centers for Disease Control and Prevention recommendations. There were 28,633 crashes, involving 33,956 vehicles and 52,033 occupants, of whom 9.9% had severe injury. At Step 0, the University of Washington model sensitivity was 40.0% and positive predictive value (PPV) was 20.7%. At Step 3, the sensitivity was 32.3 % and PPV was 10.1%. Model analysis excluding nontelematic variables decreased sensitivity and PPV. The sensitivity of the re-created General Motors model was 38.5% at Step 0 and 28.1% at Step 3. We designed a model using only vehicle collision data that was predictive of severe injury at

Motor Vehicle Crash Deaths PSA (:60)

Centers for Disease Control (CDC) Podcasts

2016-07-06

This 60 second public service announcement is based on the July 2016 CDC Vital Signs report. In the U.S., about 90 people die in motor vehicle crashes each day and thousands more are injured, resulting in hundreds of millions of dollars in direct medical costs each year. Learn what you can do to stay safe.  Created: 7/6/2016 by National Center for Injury Prevention and Control (NCIPC).   Date Released: 7/6/2016.

77 FR 73459 - California State Motor Vehicle Pollution Control Standards; Notice of Waiver of Clean Air Act...

Science.gov (United States)

2012-12-10

... ENVIRONMENTAL PROTECTION AGENCY [FRL-9759-4] California State Motor Vehicle Pollution Control Standards; Notice of Waiver of Clean Air Act Preemption; California's 2010 Model Year Heavy-Duty Vehicle and... for CARB's own motor vehicle pollution control program based on lack of compelling and extraordinary...

76 FR 23255 - Federal Motor Vehicle Safety Standards; Lamps, Reflective Devices, and Associated Equipment

Science.gov (United States)

2011-04-26

... petitions for reconsideration from Harley-Davidson Motor Company (January 18, 2008) and Ford Motor Company... [Docket No. NHTSA-2007-28322] Federal Motor Vehicle Safety Standards; Lamps, Reflective Devices, and... part, the petitions for reconsideration of the December 4, 2007, final rule reorganizing Federal Motor...

40 CFR 80.527 - Under what conditions may motor vehicle diesel fuel subject to the 15 ppm sulfur standard be...

Science.gov (United States)

2010-07-01

... vehicle diesel fuel subject to the 15 ppm sulfur standard be downgraded to motor vehicle diesel fuel... Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Motor Vehicle Diesel Fuel Standards and Requirements § 80.527 Under what conditions may motor vehicle diesel fuel subject to the 15...

The relationship between body weight and risk of death and serious injury in motor vehicle crashes.

Science.gov (United States)

Mock, Charles N; Grossman, David C; Kaufman, Robert P; Mack, Christopher D; Rivara, Frederick P

2002-03-01

We sought to investigate the effect of increased body weight on the risk of death and serious injury to occupants in motor vehicle crashes. We employed a retrospective cohort study design utilizing data from the National Automotive Sampling System, Crashworthiness Data System (CDS), 1993-1996. Subjects in the study included occupants involved in tow-away crashes of passenger cars, light trucks, vans and sport utility vehicles. Two outcomes were analyzed: death within 30 days of the crash and injury severity score (ISS). Two exposures were considered: occupant body weight and body mass index (BMI; kg/m2). Occupant weight was available on 27263 subjects (76%) in the CDS database. Mortality was 0.67%. Increased body weight was associated with increased risk of mortality and increased risk of severe injury. The odds ratio for death was 1.013 (95% CI: 1.007, 1.018) for each kilogram increase in body weight. The odds ratio for sustaining an injury with ISS > or = 9 was 1.008 (95% CI: 1.004, 1.011) for each kilogram increase in body weight. After adjustment for potentially confounding variables (age, gender, seatbelt use, seat position and vehicle curbweight), the significant relationship between occupant weight and mortality persisted. After adjustment, the relationship between occupant weight and ISS was present, although less marked. Similar trends were found when BMI was analyzed as the exposure. In conclusion, increased occupant body weight is associated with increased mortality in automobile crashes. This is probably due in part to increased co-morbid factors in the more overweight occupants. However, it is possibly also due to an increased severity of injury in these occupants. These findings may have implications for vehicle safety design, as well as for transport safety policy.

40 CFR 80.524 - What sulfur content standard applies to motor vehicle diesel fuel downstream of the refinery or...

Science.gov (United States)

2010-07-01

... to motor vehicle diesel fuel downstream of the refinery or importer? 80.524 Section 80.524 Protection... FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel; and ECA Marine Fuel Motor Vehicle Diesel Fuel Standards and Requirements § 80.524 What sulfur content standard...

In-depth analysis of drivers' merging behavior and rear-end crash risks in work zone merging areas.

Science.gov (United States)

Weng, Jinxian; Xue, Shan; Yang, Ying; Yan, Xuedong; Qu, Xiaobo

2015-04-01

This study investigates the drivers' merging behavior and the rear-end crash risk in work zone merging areas during the entire merging implementation period from the time of starting a merging maneuver to that of completing the maneuver. With the merging traffic data from a work zone site in Singapore, a mixed probit model is developed to describe the merging behavior, and two surrogate safety measures including the time to collision (TTC) and deceleration rate to avoid the crash (DRAC) are adopted to compute the rear-end crash risk between the merging vehicle and its neighboring vehicles. Results show that the merging vehicle has a bigger probability of completing a merging maneuver quickly under one of the following situations: (i) the merging vehicle moves relatively fast; (ii) the merging lead vehicle is a heavy vehicle; and (iii) there is a sizable gap in the adjacent through lane. Results indicate that the rear-end crash risk does not monotonically increase as the merging vehicle speed increases. The merging vehicle's rear-end crash risk is also affected by the vehicle type. There is a biggest increment of rear-end crash risk if the merging lead vehicle belongs to a heavy vehicle. Although the reduced remaining distance to work zone could urge the merging vehicle to complete a merging maneuver quickly, it might lead to an increased rear-end crash risk. Interestingly, it is found that the rear-end crash risk could be generally increased over the elapsed time after the merging maneuver being triggered. Copyright © 2015 Elsevier Ltd. All rights reserved.

Study on the Rollover Characteristic of In-Wheel-Motor-Driven Electric Vehicles Considering Road and Electromagnetic Excitation

OpenAIRE

Di Tan; Haitao Wang; Qiang Wang

2016-01-01

For in-wheel-motor-driven electric vehicles, the motor is installed in the wheel directly. Tyre runout and uneven load can cause magnet gap deformation in the motor, which will produce electromagnetic forces that further influence the vehicle rollover characteristics. To study the rollover characteristics, a verified 16-degree-of-freedom rollover dynamic model is introduced. Next, the vehicle rollover characteristics both with and without electromagnetic force are analyzed under conditions of...

Traffic collisions between electric mobility devices (wheelchairs) and motor vehicles: Accidents, hubris, or self-destructive behavior?

Science.gov (United States)

LaBan, Myron M; Nabity, Thomas S

2010-07-01

This study had its genesis in a personally observed collision between a motor vehicle and a motorized wheelchair (electric mobility device) on a busy street in the middle of the block at an unmarked crossing. To the observer, at the time, this appeared to be a suicidal act. This investigation was initiated to both delineate the number of these crashes nationally and understand this phenomena as a potentially planned act of self-destruction. An initial survey of police reports was immediately frustrated by an inability to separate motor vehicle and electric mobility device collisions from the much larger group that involved ambulatory citizens because both types were classified together as "pedestrian" accidents. Instead, the search engine NexisLexis was used to identify 107 newspaper articles each of which described a motor vehicle and electric mobility device accident. In the motor vehicle and electric mobility device collisions, men predominated women (3:1 ratio) with an average age of 56 yrs. Sixty of these accidents were fatal. Ninety-four percent involved an electric mobility device and 6% a manual wheelchair. In 50% of the cases, the motor vehicle was a truck, van, or sport utility vehicle. Fifty percent occurred at dusk or dawn or at night. The electric mobility device occupant was cited as the guilty party in 39% of the cases and the driver of the motor vehicle in 27%. Twenty percent were unwitnessed hit-and-run accidents, whereas "no fault" was found in 8% of the cases. Although many accidents do happen by chance, when an electric mobility device operator openly challenges busy traffic by attempting to traverse it in the middle of the block at an unmarked crossing, predisposing psychosocial factors must also be considered. Hubris or premeditated self-destructive behavior or both need to be explored as preeminent issues with reference to the prodromal of the "accident process."

Vehicle systems design optimization study

Science.gov (United States)

Gilmour, J. L.

1980-01-01

The optimum vehicle configuration and component locations are determined for an electric drive vehicle based on using the basic structure of a current production subcompact vehicle. The optimization of an electric vehicle layout requires a weight distribution in the range of 53/47 to 62/38 in order to assure dynamic handling characteristics comparable to current internal combustion engine vehicles. Necessary modification of the base vehicle can be accomplished without major modification of the structure or running gear. As long as batteries are as heavy and require as much space as they currently do, they must be divided into two packages, one at front under the hood and a second at the rear under the cargo area, in order to achieve the desired weight distribution. The weight distribution criteria requires the placement of batteries at the front of the vehicle even when the central tunnel is used for the location of some batteries. The optimum layout has a front motor and front wheel drive. This configuration provides the optimum vehicle dynamic handling characteristics and the maximum passenger and cargo space for a given size vehicle.

Study on the Rollover Characteristic of In-Wheel-Motor-Driven Electric Vehicles Considering Road and Electromagnetic Excitation

Directory of Open Access Journals (Sweden)

Di Tan

2016-01-01

Full Text Available For in-wheel-motor-driven electric vehicles, the motor is installed in the wheel directly. Tyre runout and uneven load can cause magnet gap deformation in the motor, which will produce electromagnetic forces that further influence the vehicle rollover characteristics. To study the rollover characteristics, a verified 16-degree-of-freedom rollover dynamic model is introduced. Next, the vehicle rollover characteristics both with and without electromagnetic force are analyzed under conditions of the Fixed Timing Fishhook steering and grade B road excitation. The results show that the electromagnetic force has a certain effect on the load transfer and can reduce the antirollover performance of the vehicle. Therefore, the effect of the electromagnetic force on the rollover characteristic should be considered in the vehicle design. To this end, extensive analysis was conducted on the effect of the road level, vehicle speed, and the road adhesion coefficient on the vehicle rollover stability. The results indicate that vehicle rollover stability worsens when the above-mentioned factors increase, the most influential factor being the road adhesion coefficient followed by vehicle speed and road level. This paper can offer certain theory basis for the design of the in-wheel-motor-driven electric vehicles.

40 CFR 80.581 - What are the batch testing and sample retention requirements for motor vehicle diesel fuel, NRLM...

Science.gov (United States)

2010-07-01

... retention requirements for motor vehicle diesel fuel, NRLM diesel fuel, and ECA marine fuel? 80.581 Section...) REGULATION OF FUELS AND FUEL ADDITIVES Motor Vehicle Diesel Fuel; Nonroad, Locomotive, and Marine Diesel Fuel... requirements for motor vehicle diesel fuel, NRLM diesel fuel, and ECA marine fuel? (a) Beginning on June 1...

41 CFR 101-39.203 - Obtaining motor vehicles for short-term use.

Science.gov (United States)

2010-07-01

..., AND MOTOR VEHICLES 39-INTERAGENCY FLEET MANAGEMENT SYSTEMS 39.2-GSA Interagency Fleet Management... Fleet Management System (IFMS). Short-term use vehicles may be provided through Military Traffic... General Services Administration IFMS fleet management center. [56 FR 59888, Nov. 26, 1991] ...

Design of outer-rotor type multipolar SR motor for electric vehicle

International Nuclear Information System (INIS)

Nakamura, Kenji; Suzuki, Yosuke; Goto, Hiroki; Ichinokura, Osamu

2005-01-01

In this paper, we design an outer-rotor type multipolar switched reluctance (SR) motor, and examine an application of the SR motor to an electric vehicle (EV). The design is based on a nonlinear magnetic circuit model proposed by the authors. Using the model, we can calculate dynamic characteristics of a SR motor accurately. Furthermore, by combining the nonlinear magnetic circuit model with a motor drive circuit and motion equation of an EV, we can predict dynamic characteristics such as the maximum speed, acceleration torque, and a battery current of the EV

RISK PREMIUM IN MOTOR VEHICLE INSURANCE

Directory of Open Access Journals (Sweden)

BANU ÖZGÜREL

2013-06-01

Full Text Available The pure premium or risk premium is the premium that would exactly meet the expected cost of the risk covered ignoring management expenses, commissions, contingency loading, etc. Claim frequency rate and mean claim size are required for estimation in calculating risk premiums. In this study, we discussed to estimate claim frequency rate and mean claim size with several methods and calculated risk premiums. Data, which supported our study, is provided by insurance company involving with motor vehicle insurance.

CALCULATION OF A MECHANICAL CHARACTERISTIC OF ELECTRIC TRACTION MOTOR OF ELECTRIC VEHICLE

Directory of Open Access Journals (Sweden)

Phuong Le Ngo

2017-01-01

Full Text Available The traction characteristic of an electric vehicle is the main characteristic of mechanical system that reflects its key performance indicators. Implementation of the traction characteristic is based on controlling angular speed and torque of electric traction motor in an automatic control system. The static mechanical characteristic of an electric traction motor in an automatic control system is the most important characteristic that determines weight, size and operating characteristics of an electric traction motor and serves as the basis for design. The most common variants of constructive implementation of a traction electric drive are analyzed, and a scheme is chosen for further design. Lagrange’s equation for electric mechanical system with one degree of freedom is written in generalized coordinates. In order to determine the generalized forces, elementary operation of all moments influencing on a moving car has been calculated. The resulting equation of motion of the electric vehicle corresponding to the design scheme, as well as the expressions for calculation of characteristic points of static mechanical characteristics of traction motor (i.e. the maximum and minimum time, minimum power are obtained. In order to determine the nominal values of the angular velocity and the power of electric traction motor, a method based on ensuring the movement of the vehicle in the standard cycle has been developed. The method makes it possible to calculate characteristic points of the mechanical characteristic with the lowest possible power rating. The algorithm for calculation of mechanical characteristics of the motor is presented. The method was applied to calculate static mechanical characteristic of an electric traction motor for a small urban electric truck.

School start times and teenage driver motor vehicle crashes.

Science.gov (United States)

2015-12-01

There is substantial evidence that lack of sleep is a significant factor in motor vehicle crashes experienced by teenage drivers. This report examines the hypothesis that a later high school start time may reduce crash rates by reducing the interfere...

76 FR 38209 - Meeting of the Department of Justice's (DOJ's) National Motor Vehicle Title Information System...

Science.gov (United States)

2011-06-29

... Department of Justice's (DOJ's) National Motor Vehicle Title Information System (NMVTIS) Federal Advisory... announcement of a meeting of DOJ's National Motor Vehicle Title Information System (NMVTIS) Federal Advisory... FURTHER INFORMATION CONTACT: Alissa Huntoon, Designated Federal Employee (DFE), Bureau of Justice...

77 FR 44673 - Meeting of the Department of Justice National Motor Vehicle Title Information System Federal...

Science.gov (United States)

2012-07-30

... Department of Justice National Motor Vehicle Title Information System Federal Advisory Committee AGENCY... a meeting of Department of Justice's (DOJ's) National Motor Vehicle Title Information System (NMVTIS...., Washington, DC 20531. FOR FURTHER INFORMATION CONTACT: Todd Brighton, Designated Federal Employee (DFE...

77 FR 10573 - Meeting of the Department of Justice's (DOJ's) National Motor Vehicle Title Information System...

Science.gov (United States)

2012-02-22

... Department of Justice's (DOJ's) National Motor Vehicle Title Information System (NMVTIS) Federal Advisory... announcement of a meeting of DOJ's National Motor Vehicle Title Information System (NMVTIS) Federal Advisory.... FOR FURTHER INFORMATION CONTACT: Todd Brighton, Designated Federal Employee (DFE), Bureau of Justice...

78 FR 51747 - Meeting of the Department of Justice's (DOJ's) National Motor Vehicle Title Information System...

Science.gov (United States)

2013-08-21

... Department of Justice's (DOJ's) National Motor Vehicle Title Information System (NMVTIS) Federal Advisory... announcement of a meeting of DOJ's National Motor Vehicle Title Information System (NMVTIS) Federal Advisory.... FOR FURTHER INFORMATION CONTACT: Todd Brighton, Designated Federal Employee (DFE), Bureau of Justice...

CHOOSING THE POWER OF TRACTION ELECTRIC MOTORS FOR ELECTRIC VEHICLES

OpenAIRE

O. Smirnov; A. Borisenko

2017-01-01

Recommendations on choosing the power of the electric motor, depending on the weight of the vehicle, its speed and the run distance in the «only electricity» mode are developed. Based on mathematical modeling and a number of field tests of electric vehicles, a three-dimensional dependance of the power on the weight and the speed set is built and conclusions are presented.

CHOOSING THE POWER OF TRACTION ELECTRIC MOTORS FOR ELECTRIC VEHICLES

Directory of Open Access Journals (Sweden)

O. Smirnov

2017-06-01

Full Text Available Recommendations on choosing the power of the electric motor, depending on the weight of the vehicle, its speed and the run distance in the «only electricity» mode are developed. Based on mathematical modeling and a number of field tests of electric vehicles, a three-dimensional dependance of the power on the weight and the speed set is built and conclusions are presented.

Review of Federal Motor Vehicle Safety Standards (FMVSS) for Automated Vehicles : Identifying Potential Barriers and Challenges for the Certification of Automated Vehicles Using Existing FMVSS

Science.gov (United States)

2016-03-11

The purpose of this work is to identify instances where the existing Federal Motor Vehicle Safety Standards may pose challenges to the introduction of automated vehicles. It identifies standards requiring further review - both to ensure that existing...

The effect of motor vehicle emission towards lead (Pb content of rice field soil with different clay content

Directory of Open Access Journals (Sweden)

C.C.Wati

2015-10-01

Full Text Available Motor vehicle gas emission contains lead (Pb which is a hazardous and toxic substance. Agricultural land, especially rice field, which is located nearby roads passed by many motor vehicle, are susceptible to the accumulation of Pb. If Pb is permeated by plants cultivated in the rice field, it will be very hazardous for humans as they are the final consumers. Hence, it is essential to identify Pb content of rice-field soil initiated by motor vehicle gas emission. This study was aimed to identify the effects of motor vehicle density, the distance between rice-field and road, and the clay content of soil towards Pb content of soils in Blitar and Ngawi Regencies of East Java. The method used for the study was survey method managed by using three-factor nested design with three replicates. The results of this study showed that motor vehicle density and the distance of rice field to road provide significant affected the total of Pb content of soil. However, the dissemination pattern of Pb in the soil was irregular due to the factors of climate and environment. Before Pb reached soil surface, Pb was spread out in the air due to the effect of temperature, wind velocity, vehicle velocity, size of vehicle, and road density. Consequently, the location with low motor vehicle density and positioned faraway to the road had higher total rate of Pb than the location with high motor vehicle density and positioned nearby the road. Clay content affected the total rate of Pb content as much as 37%, every 1% increase of clay content increased the total rate of Pb as much as 0.08 mg/kg.

Population-based estimates of whiplash injury using nass cds data - biomed 2009.

Science.gov (United States)

Storvik, Steven G; Stemper, Brian D; Yoganandan, Narayan; Pintar, Frank A

2009-01-01

Clinical investigations identified occupant-related factors that may predispose specific populations to increased whiplash injury susceptibility. However, clinical studies represent a specific patient population and are not representative of the population at large. The present objective was to analyze nationally-representative data to assess the association between gender and whiplash in motor vehicle rear-end impacts. A cohort of front-seat occupants in rear impacts (5-7 o'clock) from 1998-2007 were acquired using the National Automotive Sampling System (NASS) Crashworthiness Data System database. Outcome measure was "cervical spine strain" without fracture or dislocation, coded as 640278.1. Differences between injured population proportions were analyzed using Chi-Square test of independence. 1,973 rear impacts were selected, representing 936,439 weighted crashes from across the United States. Females accounted for 69% of the weighted whiplash injuries, and the proportion of females sustaining whiplash was 10% higher than males. Furthermore, gender was associated with acquiring whiplash in rear impacts (odds ratio for females: 2.16; 95% confidence interval: 1.5-3.1). Although NASS data is inherently weighted toward more severe impacts (i.e., tow-away collisions), this population-based study has demonstrated increased female susceptibility to whiplash injury. The importance of gender suggests that specific safety measures for female front-seat occupants should be addressed separately from males.

Correlation of breast cancer incidence with the number of motor vehicles and consumption of gasoline in Korea.

Science.gov (United States)

Park, Boyoung; Shin, Aesun; Jung-Choi, Kyunghee; Ha, Eunhee; Cheong, Hae-Kwan; Kim, Hyun Jeong; Park, Kyung Hwa; Jang, Sungmi; Moon, Byung-In; Ha, Mina

2014-01-01

While several reproductive and lifestyle-related factors are already well-known as established risk factors for breast cancer, environmental factors have attracted attention only recently. The objective of the current study was to assess the association between the breast cancer incidences in females, the mortality rate and the number of motor vehicles on the one side and the consumption of gasoline which could work as a major source of air pollution at the other side. The breast cancer incidences and the mortality trends were compared with various indices of westernization like dietary patterns or industrialization with 10 years lag of time. Geographical variations with 10, 15 and 20 years lag of time were assessed between the breast cancer incidence in 2010 and the number of motor vehicles as well as the consumption of gasoline. The upward trend of motor vehicle numbers proved to be comparable to those of breast cancer incidence and mortality. However, the consumption of gasoline started to decrease since the mid-1990s. The geographic distribution of motor vehicle numbers and gasoline consumption in 1990 is in a positive correlation with the breast cancer incidence rates in 2010 and the 20-year lag time (R2 0.379 with the number of motor vehicles and 0.345 with consumption of gasoline). In a linear relationship between the breast cancer incidences in 2010 and the log transformed number of motor vehicles, the log transformed consumption of gasoline in 2000 also showed a positive relationship (R2 0.367 with the number of motor vehicles and 0.329 with consumption of gasoline). The results of the current study indicate that there may be a positive relation between the number of vehicles, gasoline consumption and the incidence of breast cancer from the aspects of long-term trends and geographical variation.