Design Criteria for Achieving Low Radon Concentration Indoors

DEFF Research Database (Denmark)

Rasmussen, Torben Valdbjørn

2016-01-01

Design criteria for achieving low radon concentration indoors are presented in this paper. The paper suggests three design criteria. These criteria have to be considered at the early stage of the building design phase to meet the latest recommendations from the World Health Organization in most...... countries. The three design criteria are; first, establishing a radon barrier facing the ground; second, lowering the air pressure in the lower zone of the slab on ground facing downwards; third, diluting the indoor air with outdoor air. Three criteria when used can prevent radon infiltration and lower...... the radon concentration in the indoor air. In addition, a cheap and reliable method for measuring the radon concentration in the air indoors is described. The provision on radon in the Danish Building Regulations complies with the latest recommendations from the World Health Organization. Radon can cause...

Containment design, performance criteria and research needs for advanced reactor designs

International Nuclear Information System (INIS)

Bagdi, G.; Ali, S.; Costello, J

2004-01-01

This paper points out some important shifts in the basic expectations in the performance requirements for containment structures and discusses the areas where the containment structure design requirements and acceptance criteria can be integrated with ultimate test based insights. Although there has not been any new reactor construction in the United States for over thirty years, several designs of evolutionary and advanced reactors have already been certified. Performance requirements for containment structures under design basis and severe accident conditions and explicit consideration of seismic margins have been used in the design certification process. In the United States, the containment structure design code is the American Society of Mechanical Engineers, Boiler and Pressure Vessel Code, Section III, Division 1, Subsection NE-Class MC for the steel containment and Section III, Division 2 for reinforced and prestressed concrete reactor vessels and containments. This containment design code was based on the early concept of applying design basis internal pressure and associated load combinations that included the operating basis and safe shutdown earthquake ground motion. These early design criteria served the nuclear industry and the regulatory authorities in maintaining public health and safety. However, these early design criteria do not incorporate the performance criteria related to containment function in an integrated fashion. Research in large scale model testing of containment structures to failure from over pressurization and shake table testing using simulated ground motion, have produced insights related to failure modes and material behavior at failure. The results of this research provide the opportunity to integrate these observations into design and acceptance criteria. This integration process would identify 'gaps' in the present knowledge and future research needs. This knowledge base is important for gleaning risk-informed insights into

An Investigation Into Design Criteria for Affordable Housing Supply

Directory of Open Access Journals (Sweden)

Olanrewaju Abdul Lateef

2017-01-01

Full Text Available Affordable housing provision constitutes a very large scheme in any countries due to income distribution and national development. The supply of housing depends on many activities and processes. The purpose of the houses is to meet the requirement of the householders therefore design criteria must address the users’ requirements. The establishment of the design criteria constitutes an important activity at the initial phase of the housing development. The design criteria are prepared by the design team in collaboration with many stakeholders especially the householders. Housinsg design criteria are the requirements that must be considered prior to construction of the housing. Lack of adequate information on the design criteria would lead to poor householders’ satisfactions, increase in maintenance cost, abandonments and completed but not occupy housing. In Malaysia, many of these consequences are prevalent. However, while information on the house owners’ requirements is inconclusive, this current research set out to investigate the design criteria of affordable housing. The increase in the affordable housing gap in Malaysia can be reduced if the designers have a comprehensive understanding of users’ requirements and the design criteria. Through a cross sectional survey questionnaire, comprising 25 criteria, 7 criteria were found to be extremely critical. The Kaiser-Meyer-Olkin measure of sampling adequacy indicated that the strength of the relationships among variables was strong (KMO =0.716. Bartlett’s test of sphericity, which tests the overall significance of all the correlations within the correlation matrix, was significant χ2 (325 = 1825.075, p<0.001, indicating the data were drawn from the same population and that the criteria were related.Sustainability considerations are now being considered by the providers of affordable housing. Deductively, the results lead to the conclusion that a major factor responsible for the poor

Intelligent intefrace design criteria

International Nuclear Information System (INIS)

Sicard, Y.; Siebert, S.; Thebault, M.H.

1990-01-01

Optimum adequation between control means and the capacities of the teams of operators is sought for to achieve computerization of control and monitoring interfaces. Observation of the diagnosis activity of populations of operators in incident situations on a simulator enables design criteria well-suited to the characteristics of the detection, interpretation of symptoms and incident location tasks to be defined. A software tool based on a qualitative approach enables the design process to be systematized

Position paper: Seismic design criteria

International Nuclear Information System (INIS)

Farnworth, S.K.

1995-01-01

The purpose of this paper is to document the seismic design criteria to be used on the Title 11 design of the underground double-shell waste storage tanks and appurtenant facilities of the Multi-Function Waste Tank Facility (MWTF) project, and to provide the history and methodologies for determining the recommended Design Basis Earthquake (DBE) Peak Ground Acceleration (PGA) anchors for site-specific seismic response spectra curves. Response spectra curves for use in design are provided in Appendix A

DOE natural phenomenal hazards design and evaluation criteria

International Nuclear Information System (INIS)

Murray, R.C.; Nelson, T.A.; Short, S.A.; Kennedy, R.P.; Chander, H.; Hill, J.R.; Kimball, J.K.

1994-10-01

It is the policy of the Department of Energy (DOE) to design, construct, and operate DOE facilities so that workers, the general public, and the environment are protected from the impacts of natural phenomena hazards (NPH). Furthermore, DOE has established explicit goals of acceptable risk for NPH performance. As a result, natural phenomena hazard (earthquake, extreme wind, and flood) design and evaluation criteria for DOE facilities have been developed based on target probabilistic performance goals. These criteria include selection of design/evaluation NPH input from probabilistic hazard curves combined with commonly practiced deterministic response evaluation methods and acceptance criteria with controlled levels of conservatism. For earthquake considerations, conservatism is intentionally introduced in specification of material strengths and capacities, in the allowance of limited inelastic behavior, and by a seismic scale factor. Criteria have been developed following a graded approach for several performance goals ranging from that appropriate for normal-use facilities to that appropriate for facilities involving hazardous or critical operations. Performance goals are comprised of qualitative expressions of acceptable behavior and of target quantitative probabilities that acceptable limits of behavior are maintained. The criteria are simple procedures but have a rigorous basis. This paper addresses DOE seismic design and evaluation criteria

Towards realistic designs of wind farm layouts: Application of a novel placement selector approach

International Nuclear Information System (INIS)

Rahbari, Omid; Vafaeipour, Majid; Fazelpour, Farivar; Feidt, Michel; Rosen, Marc A.

2014-01-01

Highlights: • Challenges of turbine arrangement in wind farms are addressed. • Turbine properties and land restrictions are considered in optimization process. • The proposed approach can incorporate designer’s preferences into the optimal design. • Superior performance is attained compared to previous similar studies. • The proposed algorithm provided optimal wind farm layouts for four case studies. - Abstract: The optimal arrangement of wind turbines plays a significant role in obtaining the expected output power from wind farms. This paper addresses challenges related to typical restriction assumptions of turbine arrangement in wind farms with candidate selection approach. An applicable hybrid (quadratic assignment problem-genetic algorithm) evolutionary method with an initial candidate points selection (ICPS) approach is proposed and applied to four case studies to obtain optimal layout designs with maximum efficiency. The current study considers not only the previously utilized indicators found in the literature, such as wake effects, turbine hub height and rotor diameter, but also accounts for additional criteria such as the load-bearing capacity of soil and restrictions regarding the existence of prohibited places as well as varying wind velocities and directions. This is done to make the approach more applicable for realistic cases, and also to incorporate the preferences of expert designers. The results suggest that superior performance is attained with the proposed algorithm compared to previous similar studies. An efficiency improvement of about 3% is achieved for case one, and the algorithm provides reasonable optimal wind farm design layouts for cases two, three, and four where more restrictions exist

46 CFR 154.466 - Design criteria.

Science.gov (United States)

2010-10-01

... GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR... § 154.466 Design criteria. (a) The insulation for a cargo tank without a secondary barrier must be... cargo tank with a secondary barrier must be designed for the secondary barrier at the design temperature...

New facility shield design criteria

International Nuclear Information System (INIS)

Howell, W.P.

1981-07-01

The purpose of the criteria presented here is to provide standard guidance for the design of nuclear radiation shields thoughout new facilities. These criteria are required to assure a consistent and integrated design that can be operated safely and economically within the DOE standards. The scope of this report is confined to the consideration of radiation shielding for contained sources. The whole body dose limit established by the DOE applies to all doses which are generally distributed throughout the trunk of the body. Therefore, where the whole body is the critical organ for an internally deposited radionuclide, the whole body dose limit applies to the sum of doses received must assure control of the concentration of radionuclides in the building atmosphere and thereby limit the dose from internal sources

Thermal-hydraulic criteria for the APT tungsten neutron source design

International Nuclear Information System (INIS)

Pasamehmetoglu, K.

1998-03-01

This report presents the thermal-hydraulic design criteria (THDC) developed for the tungsten neutron source (TNS). The THDC are developed for the normal operations, operational transients, and design-basis accidents. The requirements of the safety analyses are incorporated into the design criteria, consistent with the integrated safety management and the safety-by-design philosophy implemented throughout the APT design process. The phenomenology limiting the thermal-hydraulic design and the confidence level requirements for each limit are discussed. The overall philosophy of the uncertainty analyses and the confidence level requirements also are presented. Different sets of criteria are developed for normal operations, operational transients, anticipated accidents, unlikely accidents, extremely unlikely accidents, and accidents during TNS replacement. In general, the philosophy is to use the strictest criteria for the high-frequency events. The criteria is relaxed as the event frequencies become smaller. The THDC must be considered as a guide for the design philosophy and not as a hard limit. When achievable, design margins greater than those required by the THDC must be used. However, if a specific event sequence cannot meet the THDC, expensive design changes are not necessary if the single event sequence results in sufficient margin to safety criteria and does not challenge the plant availability or investment protection considerations

Packaging design criteria for the Hanford Ecorok Packaging

International Nuclear Information System (INIS)

Mercado, M.S.

1996-01-01

The Hanford Ecorok Packaging (HEP) will be used to ship contaminated water purification filters from K Basins to the Central Waste Complex. This packaging design criteria documents the design of the HEP, its intended use, and the transportation safety criteria it is required to meet. This information will serve as a basis for the safety analysis report for packaging

Packaging design criteria for the MCO cask

International Nuclear Information System (INIS)

Clements, M.D.

1996-01-01

Approximately 2,100 metric tons of unprocessed, irradiated nuclear fuel elements are presently stored in the K Basins. To permit cleanup of the K Basins and fuel conditioning, the fuel will be transported from the K Basins to a Canister Storage Building in the 200 East Area. The purpose of this packaging design criteria is to provide criteria for the design, fabrication, and use of a packaging system to transport the large quantities of irradiated nuclear fuel elements positioned within Multiple Canister Overpacks

Multi-Criteria Approach in Multifunctional Building Design Process

Science.gov (United States)

Gerigk, Mateusz

2017-10-01

The paper presents new approach in multifunctional building design process. Publication defines problems related to the design of complex multifunctional buildings. Currently, contemporary urban areas are characterized by very intensive use of space. Today, buildings are being built bigger and contain more diverse functions to meet the needs of a large number of users in one capacity. The trends show the need for recognition of design objects in an organized structure, which must meet current design criteria. The design process in terms of the complex system is a theoretical model, which is the basis for optimization solutions for the entire life cycle of the building. From the concept phase through exploitation phase to disposal phase multipurpose spaces should guarantee aesthetics, functionality, system efficiency, system safety and environmental protection in the best possible way. The result of the analysis of the design process is presented as a theoretical model of the multifunctional structure. Recognition of multi-criteria model in the form of Cartesian product allows to create a holistic representation of the designed building in the form of a graph model. The proposed network is the theoretical base that can be used in the design process of complex engineering systems. The systematic multi-criteria approach makes possible to maintain control over the entire design process and to provide the best possible performance. With respect to current design requirements, there are no established design rules for multifunctional buildings in relation to their operating phase. Enrichment of the basic criteria with functional flexibility criterion makes it possible to extend the exploitation phase which brings advantages on many levels.

Seismic design and evaluation criteria based on target performance goals

International Nuclear Information System (INIS)

Murray, R.C.; Nelson, T.A.; Kennedy, R.P.; Short, S.A.

1994-04-01

The Department of Energy utilizes deterministic seismic design/evaluation criteria developed to achieve probabilistic performance goals. These seismic design and evaluation criteria are intended to apply equally to the design of new facilities and to the evaluation of existing facilities. In addition, the criteria are intended to cover design and evaluation of buildings, equipment, piping, and other structures. Four separate sets of seismic design/evaluation criteria have been presented each with a different performance goal. In all these criteria, earthquake loading is selected from seismic hazard curves on a probabilistic basis but seismic response evaluation methods and acceptable behavior limits are deterministic approaches with which design engineers are familiar. For analytical evaluations, conservatism has been introduced through the use of conservative inelastic demand-capacity ratios combined with ductile detailing requirements, through the use of minimum specified material strengths and conservative code capacity equations, and through the use of a seismic scale factor. For evaluation by testing or by experience data, conservatism has been introduced through the use of an increase scale factor which is applied to the prescribed design/evaluation input motion

Design criteria for prestressed concrete pressure vessels

International Nuclear Information System (INIS)

Schimmelpfennig, K.

1989-01-01

The work concerned with the PCRVs has been focussed on topics which are not sufficiently covered by the usual codes with respect to the special structure of PCRVs and the special demands on it, and different investigations yielding a basis for such specific design criteria have been carried out. Only a couple of subjects being in the fore under the aspect of defining quality enlarging design criteria for PCRVs are outlined. The materials for the concrete to be used for the PCRVs are carefully selected. (DG)

Design principles and optimal performance for molecular motors under realistic constraints

Science.gov (United States)

Tu, Yuhai; Cao, Yuansheng

2018-02-01

The performance of a molecular motor, characterized by its power output and energy efficiency, is investigated in the motor design space spanned by the stepping rate function and the motor-track interaction potential. Analytic results and simulations show that a gating mechanism that restricts forward stepping in a narrow window in configuration space is needed for generating high power at physiologically relevant loads. By deriving general thermodynamics laws for nonequilibrium motors, we find that the maximum torque (force) at stall is less than its theoretical limit for any realistic motor-track interactions due to speed fluctuations. Our study reveals a tradeoff for the motor-track interaction: while a strong interaction generates a high power output for forward steps, it also leads to a higher probability of wasteful spontaneous back steps. Our analysis and simulations show that this tradeoff sets a fundamental limit to the maximum motor efficiency in the presence of spontaneous back steps, i.e., loose-coupling. Balancing this tradeoff leads to an optimal design of the motor-track interaction for achieving a maximum efficiency close to 1 for realistic motors that are not perfectly coupled with the energy source. Comparison with existing data and suggestions for future experiments are discussed.

Using Concrete and Realistic Data in Evaluating Initial Visualization Designs

DEFF Research Database (Denmark)

Knudsen, Søren; Pedersen, Jeppe Gerner; Herdal, Thor

2016-01-01

We explore means of designing and evaluating initial visualization ideas, with concrete and realistic data in cases where data is not readily available. Our approach is useful in exploring new domains and avenues for visualization, and contrasts other visualization work, which typically operate...... under the assumption that data has already been collected, and is ready to be visualized. We argue that it is sensible to understand data requirements and evaluate the potential value of visualization before devising means of automatic data collection. We base our exploration on three cases selected...... the design case and problem, the manner in which we collected data, and the findings obtained from evaluations. Afterwards, we describe four factors of our data collection approach, and discuss potential outcomes from it....

Working Towards Unified Safety Design Criteria for Modular High Temperature Gas-cooled Reactor Designs

International Nuclear Information System (INIS)

Reitsma, Frederik; Silady, Fred; Kunitomi, Kazuhiko

2014-01-01

The Nuclear Power Development Section of the IAEA recently received approval for a Coordinated Research Project (CRP) to investigate and make proposals on modular High Temperature Gas-cooled Reactor (HTGR) Safety design criteria. It is expected that these criteria would consider past experience and existing safety standards in the light of modular HTGR material and design characteristics to propose safety design criteria. It will consider the deterministic and risk-informed safety design standards that apply to the wide spectrum of Off- normal events under development worldwide for existing and planned HTGRs. The CRP would also take into account lessons from the Fukushima Daiichi accident, clarifying the safety approach and safety evaluation criteria for design and beyond design basis events, including those events that can affect multiple reactor modules and/or are dependent on the application proximate to the plant site. (e. g., industrial process steam/heat). The logical flow of criteria is from the fundamental inherent safety characteristics of modular HTGRs and associated expected performance characteristics, to the safety functions required to ensure those characteristics during the wide spectrum of Off-normal events, and finally to specific criteria related to those functions. This is detailed in the paper with specific examples included of how it may be applied. The results of the CRP will be made available to the member states and HTGR community. (author)

Proposed design criteria for containments in Germany

International Nuclear Information System (INIS)

Schnellenbach, G.

1976-01-01

Till now all containments of German nuclear power plants have been fabricated in steel. However the nuclear power plants Gundremmingen II (KRB II) and Schmehausen II (HTR) will have prestressed concrete containments. The construction of these plants will probably start in 1975. Containments have to fulfill special tasks differing from those of pressure vessels. Because of this, design criteria for pressure vessels are not applicable to containments. On the other hand normal regulations for prestressed concrete structures are insufficient for containments. The containments KRB II and HTR are buildings of different types. KRB II is located in the interior of the reactor building of the SW-72-type. It is surrounded by a thick-walled concrete structure. HTR has the classical shape for concrete containments - vertical cylinder with spherical cap. It surrounds the reactor-building. The containment has to withstand aircraft impact forces. This influences its liner too. Design criteria have been developed for both containments, taking into consideration the special properties of these buildings. Design criteria are discussed for service-load conditions, test conditions, various forms of accident and for the ultimate load conditions. The influence of extreme external loads on the design is described. (author)

Seismic design criteria for special isotope separation plant structures

International Nuclear Information System (INIS)

Wrona, M.W.; Wuthrich, S.J.; Rose, D.L.; Starkey, J.

1989-01-01

This paper describes the seismic criteria for the design of the Special Isotope Separation (SIS) production plant. These criteria are derived from the applicable Department of Energy (DOE) orders, references and proposed standards. The SIS processing plant consistent of Load Center Building (LCB), Dye Pump Building (DPB), Laser Support Building (LSB) and Plutonium Processing Building (PPB). The facility-use category for each of the SIS building structures is identified and the applicable seismic design criteria and parameters are selected

Crew Transportation Technical Standards and Design Evaluation Criteria

Science.gov (United States)

Lueders, Kathryn L.; Thomas, Rayelle E. (Compiler)

2015-01-01

Crew Transportation Technical Standards and Design Evaluation Criteria contains descriptions of technical, safety, and crew health medical processes and specifications, and the criteria which will be used to evaluate the acceptability of the Commercial Providers' proposed processes and specifications.

Design criteria development for the structural stability of nuclear waste repository

Energy Technology Data Exchange (ETDEWEB)

Yun, C H [Korea Institute of Nuclear Safety, Taejon (Korea, Republic of); Yu, T S [Daewoo Engineering Company, Sungnam (Korea, Republic of); Ko, H M [Seoul National Univ., Seoul (Korea, Republic of)

1990-11-15

The objective of the present project is to develop design criteria for the structural stability of rock cavity for the underground repository are defined, according to which detailed descriptions for design methodologies, design stages and stability analysis of the cavity are made. The proposed criteria can be used as a guide for the preparation of design codes which are to be established as the site condition and technical emplacement procedure are fixed. The present report first reviews basic safety requirements and criteria of the underground disposal of nuclear wastes for the establishment of design concepts and stability analysis of the rock cavity. Important factors for the design are also described by considering characteristics of the wastes and underground facilities. The present project has investigated technical aspects on the design of underground structures based on the currently established underground construction technologies, and presented a proposal for design criteria for the structural stability of the nuclear waste repository. The proposed criteria consist of general provisions, geological exploration, rock classification, design process and methods, supporting system, analyses and instrumentation.

Design criteria monograph for pressurized metal cases

Science.gov (United States)

1972-01-01

Organiation and presentation of data pertaining to design of solid propellant rocket engine cases are discussed. Design criteria are presented in form of monograph based on accumulated experience and knowledge. Improvements in reliability, cost effectiveness, and engine efficiency are stressed.

Criteria procedure development for tender in construction design

Directory of Open Access Journals (Sweden)

Malykha Galina Gennad’evna

Full Text Available This article deals with the problem of criteria optimization in order to objectively evaluate the experience of an applicant (a project organization and the quality of a design product (project documentation. The methodology to be developed is based on introduction of new evaluation criteria (sub-criteria that in conjunction with the applicable criteria specified by the Law on the Contract System will allow developing the optimal procedure to evaluate competitive bids of the participants in tenders and determining the most appropriate candidate, with whom the contract will be further concluded. The article analyzes the existing criteria and their interaction with each other and describes the specifics of tenders for design in the form of open competition. The list decreases to three criteria, such as "contract price", "quality, functional and environmental characteristics of a procurement facility", "qualification of procurement participants, including availability of financial resources, equipment and other material resources necessary for the execution of the contract material resources, the presence of goodwill, professionals and other employees of a certain experience level". However, in order to upgrade the quality of assurance procedures for the design works to be performed, it was decided to apply new evaluation criteria (sub-criteria components, such as "availability of positive findings of the state out-of-departmental examination that are similar to the subject of competition, on a participant in placement of order", "availability of the certificate on approval of architectural and urban planning decisions that are similar to the subject of competition, on a participant in placement of order", "availability of the permit for the commissioning of facilities that are similar to the subject of competition, on a participant in placement of order", "availability of the contract for designer's supervision with a participant in placement of

Design Criteria Based on Aesthetic Considerations

DEFF Research Database (Denmark)

Thomsen, Bente Dahl

2009-01-01

Aesthetic criteria for designs are often debated in a very subjective manner which makes it difficult to reach consensus. In order to have a more rational and transparent process, in particular in industrial design, we propose a procedure based on Baumgarten's aesthetic considerations and Thommesen......'s dividing of a form into form elements. The procedure has been tested in student projects....

Dynamic criteria for partitioning and transmutation

International Nuclear Information System (INIS)

Lu, A.H.

1991-11-01

This paper addresses dynamic criteria intended to optimize partitioning and transmutation (P-T) concept development supporting improved nuclear waste management. Six criteria are proposed initially and the rationale for each is briefly explained. Each criterion is used as a measure (or dimension) on which the developed concepts can be evaluated. The criteria allow the P-T concepts to be evaluated in an integral system including long-term energy needs, fuel cycle, and waste management. New criteria will be identified along with the P-T concept development, and each criterion will be realistically weighted so that it is comparable in an overall criteria evaluation. The weights are subject to change as a result of technical advancements and public perception on various issues. Incomplete criteria will result in a poor choice because important factors may not be considered when the decision is made. A successful decision on the optimal P-T system depends on the completeness of criteria (dimensions) as well as realistic weights assigned to each criterion

Human factors engineering design review acceptance criteria for the safety parameter display

International Nuclear Information System (INIS)

McGevna, V.; Peterson, L.R.

1981-01-01

This report contains human factors engineering design review acceptance criteria developed by the Human Factors Engineering Branch (HFEB) of the Nuclear Regulatory Commission (NRC) to use in evaluating designs of the Safety Parameter Display System (SPDS). These criteria were developed in response to the functional design criteria for the SPDS defined in NUREG-0696, Functional Criteria for Emergency Response Facilities. The purpose of this report is to identify design review acceptance criteria for the SPDS installed in the control room of a nuclear power plant. Use of computer driven cathode ray tube (CRT) displays is anticipated. General acceptance criteria for displays of plant safety status information by the SPDS are developed. In addition, specific SPDS review criteria corresponding to the SPDS functional criteria specified in NUREG-0696 are established

Design of a Realistic Test Simulator For a Built-In Self Test Environment

Directory of Open Access Journals (Sweden)

A. Ahmad

2010-12-01

Full Text Available This paper presents a realistic test approach suitable to Design For Testability (DFT and Built- In Self Test (BIST environments. The approach is culminated in the form of a test simulator which is capable of providing a required goal of test for the System Under Test (SUT. The simulator uses the approach of fault diagnostics with fault grading procedure to provide the tests. The tool is developed on a common PC platform and hence no special software is required. Thereby, it is a low cost tool and hence economical. The tool is very much suitable for determining realistic test sequences for a targeted goal of testing for any SUT. The developed tool incorporates a flexible Graphical User Interface (GUI procedure and can be operated without any special programming skill. The tool is debugged and tested with the results of many bench mark circuits. Further, this developed tool can be utilized for educational purposes for many courses such as fault-tolerant computing, fault diagnosis, digital electronics, and safe - reliable - testable digital logic designs.

Research on high level radioactive waste repository seismic design criteria

International Nuclear Information System (INIS)

Jing Xu

2012-01-01

Review seismic hazard analysis principle and method in site suitable assessment process of Yucca Mountain Project, and seismic design criteria and seismic design basis in primary design process. Demonstrated spatial character of seismic hazard by calculated regional seismic hazard map. Contrasted different level seismic design basis to show their differences and relation. Discussed seismic design criteria for preclosure phrase of high level waste repository and preference goal under beyond design basis ground motion. (author)

Seismic design criteria for the system 80+ advanced light water reactor

International Nuclear Information System (INIS)

Manrique, M.A.; Dermitzakis, S.N.; Gerdes, L.D.; Kennedy, R.P.; Idriss, I.M.; Cassidy, J.R.

1991-01-01

This paper presents the development of seismic design criteria in support of design certification by the Nuclear Regulatory Commission (NRC) of the ABB-Combustion Engineering's System 80+ Standard Design. The design certification effort is sponsored by the US Department of Energy (DOE). The development of the design criteria included: (a) development of the seismic control motion, (b) development of generic soil profiles for anticipated sites, (c) generation of in-structure response spectra and design loads for structures and equipment through soil-structure interaction (SSI) analyses, and (d) acceptance criteria for future construction sites

Considerations for developing seismic design criteria for nuclear waste storage repositories

International Nuclear Information System (INIS)

Owen, G.N.; Yanev, P.I.; Scholl, R.E.

1980-04-01

The function of seismic design criteria is to reduce the potential for hazards that may arise during various stages of the repository life. During the operational phase, the major concern is with the possible effects of earthquakes on surface facilities, underground facilities, and equipment. During the decommissioned phase, the major concern is with the potential effects of earthquakes on the geologic formation, which may result in a reduction in isolation capacity. Existing standards and guides or criteria used for the static and seismic design of licensed nuclear facilities were reviewed and evaluated for their applicability to repository design. This report is directed mainly toward the development of seismic design criteria for the underground structures of repositories. An initial step in the development of seismic design criteria for the underground structures of repositories is the development of performance criteria, or minimum standards of acceptable behavior. A number of possible damage modes are identified for the operating phase of the repository; however, no damage modes are foreseen that would perturb the long-term function of the repository, except for the possibility of increased permeability within the rock mass. Subsequent steps in formulating acceptable seismic design criteria for the underground structures involve the quantification of the design process. The report discusses the necessity of specifying the form of ground motion that would be needed for seismic analysis and the procedures that may be used for making ground motion predictions. Further discussions outline what is needed for analysis, including rock properties, failure criteria, modeling techniques, seismic hardening criteria for the host rock mass, and probabilistic considerations

Safety principles and design criteria for nuclear power stations

International Nuclear Information System (INIS)

Gazit, M.

1982-01-01

The criteria and safety principles for the design of nuclear power stations are presented from the viewpoint of a nuclear engineer. The design, construction and operation of nuclear power stations should be carried out according to these criteria and safety principles to ensure, to a reasonable degree, that the likelihood of release of radioactivity as a result of component failure or human error should be minimized. (author)

Criteria design of the CAREM 25 reactor's core: neutronic aspects

International Nuclear Information System (INIS)

Lecot, C.A.

1990-01-01

The criteria that guided the design, from the neutronic point of view, of the CAREM reactor's core were presented. The minimum set of objectives and general criteria which permitted the design of the particular systems constituting the CAREM 25 reactor's core is detailed and stated. (Author) [es

Development of design Criteria for ITER In-vessel Components

International Nuclear Information System (INIS)

Sannazzaro, G.; Barabash, V.; Kang, S.C.; Fernandez, E.; Kalinin, G.; Obushev, A.; Martínez, V.J.; Vázquez, I.; Fernández, F.; Guirao, J.

2013-01-01

Absrtract: The components located inside the ITER vacuum chamber (in-vessel components – IC), due to their specific nature and the environments they are exposed to (neutron radiation, high heat fluxes, electromagnetic forces, etc.), have specific design criteria which are, in this paper, referred as Structural Design Criteria for In-vessel Components (SDC-IC). The development of these criteria started in the very early phase of the ITER design and followed closely the criteria of the RCC-MR code. Specific rules to include the effect of neutron irradiation were implemented. In 2008 the need of an update of the SDC-IC was identified to add missing specifications, to implement improvements, to modernise rules including recent evolutions in international codes and regulations (i.e. PED). Collaboration was set up between ITER Organization (IO), European (EUDA) and Russian Federation (RFDA) Domestic Agencies to generate a new version of SDC-IC. A Peer Review Group (PRG) composed by members of the ITER Organization and all ITER Domestic Agencies and code experts was set-up to review the proposed modifications, to provide comments, contributions and recommendations

Safety objectives and design criteria for the NHR-200

International Nuclear Information System (INIS)

Xue Dazhi; Zheng Wenxiang

1997-01-01

The construction of a nuclear district heating reactor (NHR) demonstration plant with a thermal power of 200 MW has been decided for the northeast of China. To facilitate the design and licensability a set of design criteria were developed for the NHR, based on existing general criteria for NPP but amended with regard to the unique features of NHR-200. Some key points are discussed in this paper. (author). 7 refs

Safety objectives and design criteria for the NHR-200

Energy Technology Data Exchange (ETDEWEB)

Dazhi, Xue; Wenxiang, Zheng [Institute of Nuclear Energy and Technology, Tsingua Univ., Beijing (China)

1997-09-01

The construction of a nuclear district heating reactor (NHR) demonstration plant with a thermal power of 200 MW has been decided for the northeast of China. To facilitate the design and licensability a set of design criteria were developed for the NHR, based on existing general criteria for NPP but amended with regard to the unique features of NHR-200. Some key points are discussed in this paper. (author). 7 refs.

Evaluation criteria for spectral design of camouflage

Science.gov (United States)

Škerlind, Christina; Fagerström, Jan; Hallberg, Tomas; Kariis, Hans

2015-10-01

In development of visual (VIS) and infrared (IR) camouflage for signature management, the aim is the design of surface properties of an object to spectrally match or adapt to a background and thereby minimizing the contrast perceived by a threatening sensor. The so called 'ladder model" relates the requirements for task measure of effectiveness with surface structure properties through the steps signature effectiveness and object signature. It is intended to link materials properties via platform signature to military utility and vice versa. Spectral design of a surface intends to give it a desired wavelength dependent optical response to fit a specific application of interest. Six evaluation criteria were stated, with the aim to aid the process to put requirement on camouflage and for evaluation. The six criteria correspond to properties such as reflectance, gloss, emissivity, and degree of polarization as well as dynamic properties, and broadband or multispectral properties. These criteria have previously been exemplified on different kinds of materials and investigated separately. Anderson and Åkerlind further point out that the six criteria rarely were considered or described all together in one and same publication previously. The specific level of requirement of the different properties must be specified individually for each specific situation and environment to minimize the contrast between target and a background. The criteria or properties are not totally independent of one another. How they are correlated is part of the theme of this paper. However, prioritization has been made due to the limit of space. Therefore all of the interconnections between the six criteria will not be considered in the work of this report. The ladder step previous to digging into the different material composition possibilities and choice of suitable materials and structures (not covered here), includes the object signature and decision of what the spectral response should be

46 CFR 154.460 - Design criteria.

Science.gov (United States)

2010-10-01

... GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) CERTAIN BULK DANGEROUS CARGOES SAFETY STANDARDS FOR... Barrier § 154.460 Design criteria. At static angles of heel up through 30°, a secondary barrier must (a) If a complete secondary barrier is required in § 154.459, hold all of the liquid cargo in the cargo...

Design criteria for piping and nozzles program

International Nuclear Information System (INIS)

Moore, S.E.; Bryson, J.W.

1977-01-01

This report reviews the activities and accomplishments of the Design Criteria for Piping and Nozzles program being conducted by the Oak Ridge National Laboratory for the period July 1, 1975, to September 30, 1976. The objectives of the program are to conduct integrated experimental and analytical stress analysis studies of piping system components and isolated and closely-spaced pressure vessel nozzles in order to confirm and/or improve the adequacy of structural design criteria and analytical methods used to assure the safe design of nuclear power plants. Activities this year included the development of a finite-element program for analyzing two closely spaced nozzles in a cylindrical pressure vessel; a limited-parameter study of vessels with isolated nozzles, finite-element studies of piping elbows, a fatigue test of an out-of-round elbow, summary and evaluation of experimental studies on the elastic-response and fatigue failure of tees, parameter studies on the behavior of flanged joints, publication of fifteen topical reports and papers on various experimental and analytical studies; and the development and acceptance of a number of design rules changes to the ASME Code. 2 figures, 2 tables

SEISMIC DESIGN CRITERIA FOR NUCLEAR POWER REACTORS

Energy Technology Data Exchange (ETDEWEB)

Williamson, R. A.

1963-10-15

The nature of nuclear power reactors demands an exceptionally high degree of seismic integrity. Considerations involved in defining earthquake resistance requirements are discussed. Examples of seismic design criteria and applications of the spectrum technique are described. (auth)

VDTT removal system functional design criteria

International Nuclear Information System (INIS)

Legare, D.E.

1996-01-01

Two Velocity Density Temperature Trees (H-2-815016) are to be removed from risers 14A and 1B of tank 241-SY-101. This document provides functional design criteria for the removal system. The removal system consists of a Liquid Removal Tool, Flexible Receiver (H-2-79216), Burial Container, Transport Trailers, and associated equipment

Design criteria and pressure vessel codes - an American view

International Nuclear Information System (INIS)

Tuppeny, W.H.

1975-01-01

To the pressure vessel designer, codes and criteria represent the common ground where the stress analyst and the metallurgist must interact and evolve rules and procedures which will ensure safety and open-ended responsiveness to technological, economic, and environmental change. The paper briefly discusses the evolution and rationale behind the current ASME code sections -emphasizing those portions applicable to designs operating in the creep range. The author then proposes a plan of action so that the analysts and materials people can make optimum use of time and resources, and evolve data and design criteria which will be responsive to changing technology and the economic and safety requirements of the future. (author)

Multi-material topology design of laminates with strength criteria

DEFF Research Database (Denmark)

Lund, Erik

2012-01-01

The objective of this paper is to present a novel approach for multi-material topology optimization of laminated composite structures where strength constraints are taken into account together with other global structural performance measures. The topology design problem considered contains very...... many design variables, and when strength criteria are included in the problem, a very large number of criteria functions must be considered in the optimization problem to be solved. Thus, block aggregation methods are introduced, such that global strength measures are obtained. These formulations...... are illustrated for multi-material laminated design problems where the maximum failure index is minimized while compliance and mass constraints are taken into account....

Packaging design criteria for the MCO cask

International Nuclear Information System (INIS)

Edwards, W.S.

1996-01-01

Approximately 2,100 metric tons of unprocessed, irradiated nuclear fuel elements are presently stored in the K Basins (including possibly 700 additional elements from PUREX, N Reactor, and 327 Laboratory). The basin water, particularly in the K East Basin, contains significant quantities of dissolved nuclear isotopes and radioactive fuel corrosion particles. To permit cleanup of the K Basins and fuel conditioning, the fuel will be transported from the 100 K Area to a Canister Storage Building (CSB) in the 200 East area. In order to initiate K Basin cleanup on schedule, the two-year fuel-shipping campaign must begin by December 1997. The purpose of this packaging design criteria is to provide criteria for the design, fabrication, and use of a packaging system to transport the large quantities of irradiated nuclear fuel elements positioned within Multiple Canister Overpacks

Packaging Design Criteria for the MCO Cask

International Nuclear Information System (INIS)

FLANAGAN, B.D.

2000-01-01

Approximately 2,100 metric tons of unprocessed, irradiated, nuclear fuel elements are presently stored in the K Basins (including approximately 700 additional elements from the Plutonium-Uranium Extraction Plant, N Reactor, and 327 Laboratory). To permit cleanup of the K Basins and fuel conditioning, the fuel will be transported from the 100 K Area to a Canister Storage Building (CSB) in the 200 East Area. The purpose of this packaging design criteria is to provide criteria for the design, fabrication, and use of a packaging system to transport the large quantities of irradiated nuclear fuel elements positioned within Multi-canister Overpacks. Concurrent with the K Basin cleanup, 72 Shippingport Pressurized Water Reactor Core 2 fuel assemblies will be transported from T Plant to the CSB to provide space at T Plant for K Basin sludge canisters

Optimal design criteria - prediction vs. parameter estimation

Science.gov (United States)

Waldl, Helmut

2014-05-01

G-optimality is a popular design criterion for optimal prediction, it tries to minimize the kriging variance over the whole design region. A G-optimal design minimizes the maximum variance of all predicted values. If we use kriging methods for prediction it is self-evident to use the kriging variance as a measure of uncertainty for the estimates. Though the computation of the kriging variance and even more the computation of the empirical kriging variance is computationally very costly and finding the maximum kriging variance in high-dimensional regions can be time demanding such that we cannot really find the G-optimal design with nowadays available computer equipment in practice. We cannot always avoid this problem by using space-filling designs because small designs that minimize the empirical kriging variance are often non-space-filling. D-optimality is the design criterion related to parameter estimation. A D-optimal design maximizes the determinant of the information matrix of the estimates. D-optimality in terms of trend parameter estimation and D-optimality in terms of covariance parameter estimation yield basically different designs. The Pareto frontier of these two competing determinant criteria corresponds with designs that perform well under both criteria. Under certain conditions searching the G-optimal design on the above Pareto frontier yields almost as good results as searching the G-optimal design in the whole design region. In doing so the maximum of the empirical kriging variance has to be computed only a few times though. The method is demonstrated by means of a computer simulation experiment based on data provided by the Belgian institute Management Unit of the North Sea Mathematical Models (MUMM) that describe the evolution of inorganic and organic carbon and nutrients, phytoplankton, bacteria and zooplankton in the Southern Bight of the North Sea.

Maintainability design criteria for packaging of spacecraft replaceable electronic equipment.

Science.gov (United States)

Kappler, J. R.; Folsom, A. B.

1972-01-01

Maintainability must be designed into long-duration spacecraft and equipment to provide the required high probability of mission success with the least cost and weight. The ability to perform repairs quickly and easily in a space environment can be achieved by imposing specific maintainability design criteria on spacecraft equipment design and installation. A study was funded to investigate and define design criteria for electronic equipment that would permit rapid removal and replacement in a space environment. The results of the study are discussed together with subsequent simulated zero-g demonstration tests of a mockup with new concepts for packaging.

Natural phenomena hazards design and evaluation criteria for Department of Energy Facilities

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-01-01

The Department of Energy (DOE) has issued an Order 420.1 which establishes policy for its facilities in the event of natural phenomena hazards (NPH) along with associated NPH mitigation requirements. This DOE Standard gives design and evaluation criteria for NPH effects as guidance for implementing the NPH mitigation requirements of DOE Order 420.1 and the associated implementation Guides. These are intended to be consistent design and evaluation criteria for protection against natural phenomena hazards at DOE sites throughout the United States. The goal of these criteria is to assure that DOE facilities can withstand the effects of natural phenomena such as earthquakes, extreme winds, tornadoes, and flooding. These criteria apply to the design of new facilities and the evaluation of existing facilities. They may also be used for modification and upgrading of existing facilities as appropriate. The design and evaluation criteria presented herein control the level of conservatism introduced in the design/evaluation process such that earthquake, wind, and flood hazards are treated on a consistent basis. These criteria also employ a graded approach to ensure that the level of conservatism and rigor in design/evaluation is appropriate for facility characteristics such as importance, hazards to people on and off site, and threat to the environment. For each natural phenomena hazard covered, these criteria consist of the following: Performance Categories and target performance goals as specified in the DOE Order 420.1 NPH Implementation Guide, and DOE-STD-1 021; specified probability levels from which natural phenomena hazard loading on structures, equipment, and systems is developed; and design and evaluation procedures to evaluate response to NPH loads and criteria to assess whether or not computed response is permissible.

Development and implementation of the TPX structural and cryogenic design criteria

International Nuclear Information System (INIS)

Zatz, I.; Heitzenroeder, P.; Schultz, J.H.

1993-01-01

The Tokamak Physics Experiment (TPX) is a superconducting tokamak utilizing both Nb 3 Sn and NbTi superconducting magnets and will feature a low-activation titanium alloy vacuum vessel and carbon-carbon composite divertors. Due to the unique nature of the component designs, materials, and environment, the TPX project felt it necessary to develop a design criteria (code) which will specifically address the structural and cryogenic design aspects of such a device. The developed code is intended to serve all components of the device; namely, the TF and PF magnets, vacuum vessel, first wall and divertor, cryostat, diagnostics, heating devices, shielding, and all associated structural elements. The structural portion is based largely on that developed for the Burning Plasma Experiment (BPX), which was modeled after the CIT Vacuum Vessel Structural Design Criteria and ASME Boiler and Pressure Vessel (B ampersand PV) Code. The cryogenic criteria is largely modeled after that proposed in the ITER CDA. This paper summarizes the TPX Criteria document

Improved transcranial magnetic stimulation coil design with realistic head modeling

Science.gov (United States)

Crowther, Lawrence; Hadimani, Ravi; Jiles, David

2013-03-01

We are investigating Transcranial magnetic stimulation (TMS) as a noninvasive technique based on electromagnetic induction which causes stimulation of the neurons in the brain. TMS can be used as a pain-free alternative to conventional electroconvulsive therapy (ECT) which is still widely implemented for treatment of major depression. Development of improved TMS coils capable of stimulating subcortical regions could also allow TMS to replace invasive deep brain stimulation (DBS) which requires surgical implantation of electrodes in the brain. Our new designs allow new applications of the technique to be established for a variety of diagnostic and therapeutic applications of psychiatric disorders and neurological diseases. Calculation of the fields generated inside the head is vital for the use of this method for treatment. In prior work we have implemented a realistic head model, incorporating inhomogeneous tissue structures and electrical conductivities, allowing the site of neuronal activation to be accurately calculated. We will show how we utilize this model in the development of novel TMS coil designs to improve the depth of penetration and localization of stimulation produced by stimulator coils.

36 CFR 212.55 - Criteria for designation of roads, trails, and areas.

Science.gov (United States)

2010-07-01

... roads, trails, and areas. 212.55 Section 212.55 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE TRAVEL MANAGEMENT Designation of Roads, Trails, and Areas for Motor Vehicle Use § 212.55 Criteria for designation of roads, trails, and areas. (a) General criteria for designation of...

Seismic design and evaluation criteria for DOE facilities (DOE-STD-1020-XX)

International Nuclear Information System (INIS)

Short, S.A.; Kennedy, R.P.; Murray, R.C.

1993-01-01

Seismic design and evaluation criteria for DOE facilities are provided in DOE-STD-1020-XX. The criteria include selection of design/evaluation seismic input from probabilistic seismic hazard curves combined with commonly practiced deterministic response evaluation methods and acceptance criteria with controlled levels of conservatism. Conservatism is intentionally introduced in specification of material strengths and capacities, in the allowance of limited inelastic behavior and by a seismic load factor. These criteria are based on the performance or risk goals specified in DOE 5480.28. Criteria have been developed following a graded approach for several performance goals ranging from that appropriate for normal-use facilities to that appropriate for facilities involving hazardous or critical operations. Performance goals are comprised of desired behavior and of the probability of not achieving that behavior. Following the seismic design/evaluation criteria of DOE-STD-1020-XX is sufficient to demonstrate that the probabilistic performance or risk goals are achieved. The criteria are simple procedures but with a sound, rigorous basis for the achievement of goals

Establishing seismic design criteria to achieve an acceptable seismic margin

International Nuclear Information System (INIS)

Kennedy, R.P.

1997-01-01

In order to develop a risk based seismic design criteria the following four issues must be addressed: (1) What target annual probability of seismic induced unacceptable performance is acceptable? (2). What minimum seismic margin is acceptable? (3) Given the decisions made under Issues 1 and 2, at what annual frequency of exceedance should the Safe Shutdown Earthquake ground motion be defined? (4) What seismic design criteria should be established to reasonably achieve the seismic margin defined under Issue 2? The first issue is purely a policy decision and is not addressed in this paper. Each of the other three issues are addressed. Issues 2 and 3 are integrally tied together so that a very large number of possible combinations of responses to these two issues can be used to achieve the target goal defined under Issue 1. Section 2 lays out a combined approach to these two issues and presents three potentially attractive combined resolutions of these two issues which reasonably achieves the target goal. The remainder of the paper discusses an approach which can be used to develop seismic design criteria aimed at achieving the desired seismic margin defined in resolution of Issue 2. Suggestions for revising existing seismic design criteria to more consistently achieve the desired seismic margin are presented

Durability-Based Design Criteria for a Chopped-Glass-Fiber Automotive Structural Composite; TOPICAL

International Nuclear Information System (INIS)

Battiste, R.L.; Corum, J.M.; Ren, W.; Ruggles, M.B.

1999-01-01

This report provides recommended durability-based design criteria for a chopped-glass-fiber reinforced polymeric composite for automotive structural applications. The criteria closely follow the framework of an earlier criteria document for a continuous-strand-mat (CSM) glass-fiber reference composite. Together these design criteria demonstrate a framework that can be adapted for future random-glass-fiber composites for automotive structural applications

Canberra Alpha Sentry Installation Functional Design Criteria (FDC)

International Nuclear Information System (INIS)

WHITE, W.F.

1999-01-01

This document provides the functional design criteria for the installation of the Canberra Alpha Sentry System at selected locations within the Plutonium Finishing Plant (PFP). The equipment being installed is identified by part number in Section 3 and the locations are given in Section 5. The design, procurement and installation are assigned to Fluor Federal Services

Tank SY-101 void fraction instrument functional design criteria

International Nuclear Information System (INIS)

McWethy, L.M.

1994-01-01

This document presents the functional design criteria for design, analysis, fabrication, testing, and installation of a void fraction instrument for Tank SY-101. This instrument will measure the void fraction in the waste in Tank SY-101 at various elevations

FHR Generic Design Criteria

Energy Technology Data Exchange (ETDEWEB)

Flanagan, George F [ORNL; Holcomb, David Eugene [ORNL; Cetiner, Sacit M [ORNL

2012-06-01

The purpose of this document is to provide an initial, focused reference to the safety characteristics of and a licensing approach for Fluoride-Salt-Cooled High-Temperature Reactors (FHRs). The document does not contain details of particular reactor designs nor does it attempt to identify or classify either design basis or beyond design basis accidents. Further, this document is an initial attempt by a small set of subject matter experts to document the safety and licensing characteristics of FHRs for a larger audience. The document is intended to help in setting the safety and licensing research, development, and demonstration path forward. Input from a wider audience, further technical developments, and additional study will be required to develop a consensus position on the safety and licensing characteristics of FHRs. This document begins with a brief overview of the attributes of FHRs and then a general description of their anticipated safety performance. Following this, an overview of the US nuclear power plant approval process is provided that includes both test and power reactors, as well as the role of safety standards in the approval process. The document next describes a General Design Criteria (GDC) - based approach to licensing an FHR and provides an initial draft set of FHR GDCs. The document concludes with a description of a path forward toward developing an FHR safety standard that can support both a test and power reactor licensing process.

On the construction of experimental designs for a given task by jointly optimizing several quality criteria: Pareto-optimal experimental designs.

Science.gov (United States)

Sánchez, M S; Sarabia, L A; Ortiz, M C

2012-11-19

Experimental designs for a given task should be selected on the base of the problem being solved and of some criteria that measure their quality. There are several such criteria because there are several aspects to be taken into account when making a choice. The most used criteria are probably the so-called alphabetical optimality criteria (for example, the A-, E-, and D-criteria related to the joint estimation of the coefficients, or the I- and G-criteria related to the prediction variance). Selecting a proper design to solve a problem implies finding a balance among these several criteria that measure the performance of the design in different aspects. Technically this is a problem of multi-criteria optimization, which can be tackled from different views. The approach presented here addresses the problem in its real vector nature, so that ad hoc experimental designs are generated with an algorithm based on evolutionary algorithms to find the Pareto-optimal front. There is not theoretical limit to the number of criteria that can be studied and, contrary to other approaches, no just one experimental design is computed but a set of experimental designs all of them with the property of being Pareto-optimal in the criteria needed by the user. Besides, the use of an evolutionary algorithm makes it possible to search in both continuous and discrete domains and avoid the need of having a set of candidate points, usual in exchange algorithms. Copyright © 2012 Elsevier B.V. All rights reserved.

Reinventing Sex: The Construction of Realistic Definitions of Sex and Gender.

Science.gov (United States)

Small, Chanley M.

1998-01-01

Presents a set of criteria for constructing a fair and realistic understanding of sex. Recognizes the impact that science can have on social policies and values and recommends that the definitions of sex and gender be carefully crafted. (DDR)

2D Decision-Making for Multi-Criteria Design Optimization

National Research Council Canada - National Science Library

Engau, A; Wiecek, M. M

2006-01-01

The high dimensionality encountered in engineering design optimization due to large numbers of performance criteria and specifications leads to cumbersome and sometimes unachievable tradeoff analyses...

Advanced composite structures. [metal matrix composites - structural design criteria for spacecraft construction materials

Science.gov (United States)

1974-01-01

A monograph is presented which establishes structural design criteria and recommends practices to ensure the design of sound composite structures, including composite-reinforced metal structures. (It does not discuss design criteria for fiber-glass composites and such advanced composite materials as beryllium wire or sapphire whiskers in a matrix material.) Although the criteria were developed for aircraft applications, they are general enough to be applicable to space vehicles and missiles as well. The monograph covers four broad areas: (1) materials, (2) design, (3) fracture control, and (4) design verification. The materials portion deals with such subjects as material system design, material design levels, and material characterization. The design portion includes panel, shell, and joint design, applied loads, internal loads, design factors, reliability, and maintainability. Fracture control includes such items as stress concentrations, service-life philosophy, and the management plan for control of fracture-related aspects of structural design using composite materials. Design verification discusses ways to prove flightworthiness.

Design criteria document, electrical system, K-Basin essential systems recovery, Project W-405

International Nuclear Information System (INIS)

Hoyle, J.R.

1994-01-01

This Design Criteria Document provides the criteria for design and construction of electrical system modifications for 100K Area that are essential to protect the safe operation and storage of spent nuclear fuel in the K-Basin facilities

Design criteria for the structural analysis of shipping cask containment vessels

International Nuclear Information System (INIS)

Anon.

1979-01-01

10 CFR Part 71, Sections 71.35 and 71.36, require that packages used to transport radioactive materials meet specified normal and hypothetical accident conditions. Acceptable design criteria are presented for use in the structural analysis of the containment vessels of Type B packages used to transport irradiated nuclear fuel. Alternative design criteria meeting the structural requirements of 10 CFR Part 71, Section 71.35 and 71.36, may also be used

Maintaining Department of Energy facilities general design criteria

International Nuclear Information System (INIS)

Metzler, J.F.

1985-01-01

A General Design Criteria (GDC) Planning Board has been established in the Department of Energy to streamline the improvement and maintenance of the GDC Manual. This Planning Board, composed of a membership from field organizations and Headquarters programmatic offices, started work on 15 enhancements to the GDC Manual. One of those enhancements details natural phenomena hazards criteria. In the past year the Planning Board submitted a major recommendation which has been implemented into what is known as the GDC Improvements project. The result of this project pledges to dramatically increase the GDC Manual's utilization and effectiveness

78 FR 38091 - Airworthiness Criteria: Proposed Airship Design Criteria for Lockheed Martin Aeronautics Model...

Science.gov (United States)

2013-06-25

..., 2012 Lockheed Martin Aeronautics submitted an application for type certification for the model LMZ1M..., views, or arguments as they may desire. Commenters should identify the proposed design criteria on the... Lockheed Martin Aeronautics submitted an application for type certification for the model LMZ1M airship...

Radiological design criteria for fusion power test facilities

International Nuclear Information System (INIS)

Singh, M.S.; Campbell, G.W.

1982-01-01

The quest for fusion power and understanding of plasma physics has resulted in planning, design, and construction of several major fusion power test facilities, based largely on magnetic and inertial confinement concepts. We have considered radiological design aspects of the Joint European Torus (JET), Livermore Mirror and Inertial Fusion projects, and Princeton Tokamak. Our analyses on radiological design criteria cover acceptable exposure levels at the site boundary, man-rem doses for plant personnel and population at large, based upon experience gained for the fission reactors, and on considerations of cost-benefit analyses

2D Decision-Making for Multi-Criteria Design Optimization

National Research Council Canada - National Science Library

Engau, A; Wiecek, M. M

2006-01-01

.... To facilitate those analyses and enhance decision-making and design selection, we propose to decompose the original problem by considering only pairs of criteria at a time, thereby making tradeoff...

Food chain design using multi criteria decision making, an approach to complex design issues

NARCIS (Netherlands)

Linnemann, A.R.; Hendrix, E.M.T.; Apaiah, R.K.; Boekel, van M.A.J.S.

2015-01-01

Designing a food supply chain for a completely new product involves many stakeholders and knowledge from disciplines in natural and social sciences. This paper describes how Multi Criteria Decision Making (MCDM) facilitated designing a food supply chain in a case of Novel Protein Foods. It made the

Novel high-fidelity realistic explosion damage simulation for urban environments

Science.gov (United States)

Liu, Xiaoqing; Yadegar, Jacob; Zhu, Youding; Raju, Chaitanya; Bhagavathula, Jaya

2010-04-01

Realistic building damage simulation has a significant impact in modern modeling and simulation systems especially in diverse panoply of military and civil applications where these simulation systems are widely used for personnel training, critical mission planning, disaster management, etc. Realistic building damage simulation should incorporate accurate physics-based explosion models, rubble generation, rubble flyout, and interactions between flying rubble and their surrounding entities. However, none of the existing building damage simulation systems sufficiently faithfully realize the criteria of realism required for effective military applications. In this paper, we present a novel physics-based high-fidelity and runtime efficient explosion simulation system to realistically simulate destruction to buildings. In the proposed system, a family of novel blast models is applied to accurately and realistically simulate explosions based on static and/or dynamic detonation conditions. The system also takes account of rubble pile formation and applies a generic and scalable multi-component based object representation to describe scene entities and highly scalable agent-subsumption architecture and scheduler to schedule clusters of sequential and parallel events. The proposed system utilizes a highly efficient and scalable tetrahedral decomposition approach to realistically simulate rubble formation. Experimental results demonstrate that the proposed system has the capability to realistically simulate rubble generation, rubble flyout and their primary and secondary impacts on surrounding objects including buildings, constructions, vehicles and pedestrians in clusters of sequential and parallel damage events.

Planning, design and technological criteria of conventional and nuclear shelters

International Nuclear Information System (INIS)

Sadoon, A.S.

1989-01-01

The thesis aims to establish a special criteria for building the shelters in two types. The conventional and nuclear, in respect to planning design and technological aspects, and finally establishing a special reference of planning, design and technology for Iraq which can be used when planning or designing a conventional or nuclear shelter. The thesis included four chapters, the first chapter included definition of shelters, and explanation of the effects of all types of weapons on buildings, and the second chapter included definition of planning and design concepts of shelters in its two types and analytical studies for international examples. The third chapter covered definition for technologies of structural, mechanical, electrical and sanitary systems. The fourth chapter included details of a case study in order to approach the results of research which included the conclusions, recommendations, criteria and prospects of planning design and technological aspects. 51 tabs.; 180 figs.; 32 refs.; 15 apps

Design criteria of integrated reactors based on transients

International Nuclear Information System (INIS)

Zanocco, P.; Gimenez, M.; Delmastro, D.

1999-01-01

A new tendency in integrated reactors conceptual design is to include safety criteria through accident analysis. In this work, the effect of design parameters in a Loss of Heat Sink transient using design maps is analyzed. Particularly, geometry related parameters and reactivity coefficients are studied. Also the effect of primary relief/safety valve during the transient is evaluated. A design map for valve area vs. coolant density reactivity coefficient is obtained. A computer code (HUARPE) is developed in order to simulate these transients. Coolant, steam dome, pressure vessel structures and core models are implemented. This code is checked against TRAC with satisfactory results. (author)

Safety Design Criteria of Indian Sodium Cooled Fast Reactors

International Nuclear Information System (INIS)

Pillai, P.; Chellapandi, P.; Chetal, S.C.; Vasudeva Rao, P.R.

2013-01-01

• Important feedback has been gained through the design and safety review of PFBR. • The safety criteria document prepared by AERB and IGCAR would provide important input to prepare the dedicated document for the Sodium cooled Fast Reactors at the national and international level. • A common approach with regard to safety, among countries pursuing fast reactor program, is desirable. • Sharing knowledge and experimental facilities on collaborative basis. • Evolution of strong safety criteria – fundamental to assure safety

Overview of core designs and requirements/criteria for core restraint systems

International Nuclear Information System (INIS)

Sutherland, W.H.

1984-09-01

The requirements and lifetime criteria for the design of a Liquid Metal Fast Breeder Reactor (LMFBR) Core Restraint System are presented. A discussion of the three types of core restraint systems used in LMFBR core design is given. Details of the core restraint system selected for FFTF are presented and the reasons for this selection given. Structural analysis procedures being used to manage the FFTF assembly irradiations are discussed. Efforts that are ongoing to validate the calculational methods and lifetime criteria are presented

Design criteria for Reedy Creek Demonstration Project

International Nuclear Information System (INIS)

Felicione, F.S.; Logan, J.A.

1980-11-01

This document defines the basic criteria for the 100-ton/day pilot plant which will use the Andco-Torrax pyrolysis process at Walt Disney World in Orlando, Florida, to produce hot water. The waste will simulate transuranic wastes which are stored at INEL. The Andco-Torrax process is designed to convert mixed municipal refuse into energy and is called slagging pyrolysis solid waste conversion

Compliance to Universal Design Criteria in Nursing Homes of Tehran

Directory of Open Access Journals (Sweden)

Morteza Nasiri

2016-07-01

Conclusion: The findings of this study showed that the majority of nursing homes evaluated did not follow the universal design criteria. Therefore, providing the proper guidelines and policies to promote the universal design observance in nursing homes is considered as a major necessity.

Safety Design Criteria (SDC) for Gen-IV Sodium-cooled Fast Reactor

International Nuclear Information System (INIS)

Nakai, Ryodai

2013-01-01

SDC Development Background & Objectives: • Safety Design Criteria (SDC) Development for Gen-IV SFR: – Proposed at the GIF Policy Group (PG) meeting in October 2010 –SDC “harmonization” is increasingly important for: • Realization of enhanced safety designs meeting to Gen-IV safety goals and safety approach common to SFR systems; • Preparation for the forthcoming licensing in the near future; • Because Gen-IV SFR are progressing into conceptual design stage. • The SDC is the Reference criteria: – Of the designs of safety-related Structures, Systems & Components that are specific to the SFR system; – For clarifying the requisites systematically & comprehensively; – When the technology developers apply the basic safety approach and use the codes & standards for conceptual design of the Gen-IV SFR system

Safety approach to the selection of design criteria for the CRBRP reactor refueling system

International Nuclear Information System (INIS)

Meisl, C.J.; Berg, G.E.; Sharkey, N.F.

1979-01-01

The selection of safety design criteria for Liquid Metal Fast Breeder Reactor (LMFBR) refueling systems required the extrapolation of regulations and guidelines intended for Light Water Reactor refueling systems and was encumbered by the lack of benefit from a commercially licensed predecessor other than Fermi. The overall approach and underlying logic are described for developing safety design criteria for the reactor refueling system (RRS) of the Clinch River Breeder Reactor Plant (CRBRP). The complete selection process used to establish the criteria is presented, from the definition of safety functions to the finalization of safety design criteria in the appropriate documents. The process steps are illustrated by examples

Functional design criteria for an exploratory shaft facility in salt: Technical report

International Nuclear Information System (INIS)

1986-11-01

The purpose of the Functional Criteria for Design is to provide technical direction for the development of detailed design criteria for the exploratory shaft facility. This will assure that the exploratory shaft facility will be designed in accordance with the current Mission Plan as well as the Nuclear Waste Policy Act and 10 CFR Part 60, which will facilitate the licensing process. The functional criteria for design are not intended to limit or constrain the designer's flexibility. The following philosophies will be incorporated in the designs: (1) The exploratory shaft will be designed to fulfill its intended purpose which is to characterize the salt site by subsurface testing; (2) the design will minimize any adverse impact which the facility may cause to the environment and any damage to the site if it should be found suitable for a repository; (3) the health and safety of the public and of the workers will be an essential factor in the design; (4) sound engineering principles and practices will be consistently employed in the design process; (5) the exploratory shaft and related surface and subsurface facilities will be designed to be economical and reliable in construction, operation, and maintenance; and (6) the exploratory shaft facility will be designed in accordance with applicable federal, state, and local regulations, as well as all applicable national consensus codes and standards

High level radioactive waste management facility design criteria

International Nuclear Information System (INIS)

Sheikh, N.A.; Salaymeh, S.R.

1993-01-01

This paper discusses the engineering systems for the structural design of the Defense Waste Processing Facility (DWPF) at the Savannah River Site (SRS). At the DWPF, high level radioactive liquids will be mixed with glass particles and heated in a melter. This molten glass will then be poured into stainless steel canisters where it will harden. This process will transform the high level waste into a more stable, manageable substance. This paper discuss the structural design requirements for this unique one of a kind facility. A special emphasis will be concentrated on the design criteria pertaining to earthquake, wind and tornado, and flooding

Overview of core designs and requirements/criteria for core restraint systems

International Nuclear Information System (INIS)

Sutherland, W.H.

1984-01-01

The requirements and lifetime criteria for the design of a Liquid Metal Fast Breeder Reactor (LMFBR) Core Restraint System is presented. A discussion of the three types of core restraint systems used in LMFBR core design is given. Details of the core restraint system selected for FFTF are presented and the reasons for this selection given. Structural analysis procedures being used to manage the FFTF assembly irradiations are discussed. Efforts that are ongoing to validate the calculational methods and lifetime criteria are presented. (author)

Design Processes and Criteria for the X-51A Flight Vehicle Airframe

National Research Council Canada - National Science Library

Lane, Jeffrey

2007-01-01

.... This paper summarizes the X-51A vehicle mission requirements, system design, design processes used for airframe synthesis, design safety factors, success criteria and issues facing the incorporation...

Any realistic theory must be computationally realistic: a response to N. Gisin's definition of a Realistic Physics Theory

OpenAIRE

Bolotin, Arkady

2014-01-01

It is argued that the recent definition of a realistic physics theory by N. Gisin cannot be considered comprehensive unless it is supplemented with requirement that any realistic theory must be computationally realistic as well.

Packaging design criteria, transfer and disposal of 102-AP mixer pump

International Nuclear Information System (INIS)

Carlstrom, R.F.

1994-01-01

A mixer pump installed in storage tank 241-AP-102 (102-AP) has failed. This pump is referred to as the 102-AP mixer pump (APMP). The APMP will be removed from 102-AP 1 and a new pump will be installed. The main purpose of the Packaging Design Criteria (PDC) is to establish criteria necessary to design and fabricate a shipping container for the transfer and storage of the APMP from 102-AP. The PDC will be used as a guide to develop a Safety Evaluation for Packaging (SEP)

Fuel safety criteria technical review - Results of OECD/CSNI/PWG2 Task Force on Fuel Safety Criteria

International Nuclear Information System (INIS)

Hollasky, N.; Valtonen, K.; Hache, G.; Gross, H.; Bakker, K.; Recio, M.; Bart, G.; Zimmermann, M.; Van Doesburg, W.; Killeen, J.; Meyer, R.O.; Speis, T.

2000-01-01

With the advent of advanced fuel and core designs, the adoption of more aggressive operational modes and the implementation of more accurate (best estimate or statistical) design and analysis methods, there is a concern if safety margins have remained adequate. Most - if not all - of the currently existing safety criteria were established during the 60's and early 70's, and verified against experiments with fuel that was available at that time, mostly with unirradiated specimens. Verification was of course performed as designs progressed in later years, however mostly with the aim to be able to prove that these designs adequately complied with existing criteria, and not to establish new limits. The OECD/CSNI/PWG2 Task Force on Fuel Safety Criteria (TFFSC) was therefore given the mandate to technically review the existing fuel safety criteria, focusing on the 'new design' elements (new fuel and core design, cladding materials, manufacturing processes, high burnup, MOX, etc.) introduced by the industry. It should also identify if additional efforts may be required (experimental, analytical) to ensure that the basis for fuel safety criteria is adequate to address the relevant safety issues. In this report, fuel-related criteria are discussed without attempting to categorize them according to event type or risk significance. For each of these 20 criteria, we present a brief description of the criterion as it is used in several applications along with the rationale for having such a criterion. New design elements, such as different cladding materials, higher burnup, and the use of MOX fuels, can affect fuel-related margins and, in some cases, the criteria themselves. Some of the more important effects are mentioned in order to indicate whether the criteria need to be re-evaluated. The discussion may not cover all possible effects, but should be sufficient to identify those criteria that need to be addressed. A summary of these discussions is given in Section 7. As part

Protocol - realist and meta-narrative evidence synthesis: Evolving Standards (RAMESES

Directory of Open Access Journals (Sweden)

Westhorp Gill

2011-08-01

Full Text Available Abstract Background There is growing interest in theory-driven, qualitative and mixed-method approaches to systematic review as an alternative to (or to extend and supplement conventional Cochrane-style reviews. These approaches offer the potential to expand the knowledge base in policy-relevant areas - for example by explaining the success, failure or mixed fortunes of complex interventions. However, the quality of such reviews can be difficult to assess. This study aims to produce methodological guidance, publication standards and training resources for those seeking to use the realist and/or meta-narrative approach to systematic review. Methods/design We will: [a] collate and summarise existing literature on the principles of good practice in realist and meta-narrative systematic review; [b] consider the extent to which these principles have been followed by published and in-progress reviews, thereby identifying how rigour may be lost and how existing methods could be improved; [c] using an online Delphi method with an interdisciplinary panel of experts from academia and policy, produce a draft set of methodological steps and publication standards; [d] produce training materials with learning outcomes linked to these steps; [e] pilot these standards and training materials prospectively on real reviews-in-progress, capturing methodological and other challenges as they arise; [f] synthesise expert input, evidence review and real-time problem analysis into more definitive guidance and standards; [g] disseminate outputs to audiences in academia and policy. The outputs of the study will be threefold: 1. Quality standards and methodological guidance for realist and meta-narrative reviews for use by researchers, research sponsors, students and supervisors 2. A 'RAMESES' (Realist and Meta-review Evidence Synthesis: Evolving Standards statement (comparable to CONSORT or PRISMA of publication standards for such reviews, published in an open

Functional design criteria for the self-installing liquid observation well

International Nuclear Information System (INIS)

Parra, S.A.

1996-01-01

This document presents the functional Design Criteria for installing liquid observation wells (LOWs) into single-shell tanks containing ferrocyanide and organic wastes. The LOWs will be designed to accommodate the deployment of gamma, neutron, and electromagnetic induction probes and to interface with the existing tank structure and environment

Progress in realistic LOCA analysis

Energy Technology Data Exchange (ETDEWEB)

Young, M Y; Bajorek, S M; Ohkawa, K [Westinghouse Electric Corporation, Pittsburgh, PA (United States)

1994-12-31

While LOCA is a complex transient to simulate, the state of art in thermal hydraulics has advanced sufficiently to allow its realistic prediction and application of advanced methods to actual reactor design as demonstrated by methodology described in this paper 6 refs, 5 figs, 3 tabs

Design Criteria for Process Wastewater Pretreatment Facilities

Science.gov (United States)

1988-05-01

Stripping Column H13 ’Re Purpose: The purpose of this report, is to provide design criteria for pretreatment needs for ’ I. INTRODUCTION ’". discharge of...which a portion of the vessel is filled with packing. Packing materials vary from corrugated steel to bundles of fibers (Langdon et al., 1972) to beds...concentration(s) using Table 20. Wastewater treatability studies should be considered as a process-screening tool for all wastewater streams for

Standard guide for design criteria for plutonium gloveboxes

CERN Document Server

American Society for Testing and Materials. Philadelphia

2009-01-01

1.1 This guide defines criteria for the design of glovebox systems to be used for the handling of plutonium in any chemical or physical form or isotopic composition or when mixed with other elements or compounds. Not included in the criteria are systems auxiliary to the glovebox systems such as utilities, ventilation, alarm, and waste disposal. Also not addressed are hot cells or open-face hoods. The scope of this guide excludes specific license requirements relating to provisions for criticality prevention, hazards control, safeguards, packaging, and material handling. Observance of this guide does not relieve the user of the obligation to conform to all federal, state, and local regulations for design and construction of glovebox systems. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user...

Design criteria for plutonium gloveboxes

International Nuclear Information System (INIS)

Anon.

1981-01-01

The standard defines criteria for the design of glovebox systems to be used for the handling of plutonium in any form or isotopic composition or when mixed with other elements or compounds. The glovebox system is a series of physical barriers provided with glove ports and gloves, through which process and maintenance operations may be performed, together with an operating ventilation system. The system minimizes the potential for release of radioactive material to the environment, protects operators from contamination, and mitigates the consequences of abnormal condiations. The standard covers confinement, construction, materials, windows, glove ports, gloves, equipment insertion and removal, lighting, ventilation, fire protection, criticality prevention, services and utilities, radiation shielding, waste systems, monitoring and alarm systems, safeguards, quality assurance, and decommissioning

California-Oregon 500-kV transmission line development of design criteria

International Nuclear Information System (INIS)

Simpson, K.D.

1990-01-01

The California-Oregon Transmission Project (COTP) encompassed the design and construction of a third 500-kV ac intertie between California and the Pacific Northwest Transmission system. Sargent ampersand Lundy's (S ampersand L) scope of work in the COTP includes the design of approximately 150 miles of new single-circuit, 500-kV transmission line from southern Oregon to the vicinity of Redding, California. This paper presents the development of the design criteria for this segment of the project, which crosses diverse topographic and climatic regions. This project is an example of the increasing utilization of computers in transmission line engineering. Almost all aspects of design involved the use of the computer. Also, the development of the design criteria for this project coincided with an early release of the TLWorkstation software package by EPRI. TLWorkstation is an engineering workstation containing a family of programs for various aspects of transmission line design. This engineering software allows for increasing refinement in the design and economic optimization of transmission lines and is becoming an important design tool for transmission engineers

Designing virtual audiences for fear of public speaking training - an observation study on realistic nonverbal behavior.

Science.gov (United States)

Poeschl, Sandra; Doering, Nicola

2012-01-01

Virtual Reality technology offers great possibilities for Cognitive Behavioral Therapy of fear of public speaking: Clients can be exposed to virtual fear-triggering stimuli (exposure) and are able to role-play in virtual environments, training social skills to overcome their fear. Usually, prototypical audience behavior (neutral, social and anti-social) serves as stimulus in virtual training sessions, although there is significant lack of theoretical basis on typical audience behavior. The study presented deals with the design of a realistic virtual presentation scenario. An audience (consisting of n=18 men and women) in an undergraduate seminar was observed during three frontal lecture sessions. Behavior frequency of four nonverbal dimensions (eye contact, facial expression, gesture, and posture) was rated by means of a quantitative content analysis. Results show audience behavior patterns which seem to be typical in frontal lecture contexts, like friendly and neutral face expressions. Additionally, combined and even synchronized behavioral patterns between participants who sit next to each other (like turning to the neighbor and start talking) were registered. The gathered data serve as empirical design basis for a virtual audience to be used in virtual training applications that stimulate the experiences of the participants in a realistic manner, thereby improving the experienced presence in the training application.

Design criteria tank farm storage and staging facility

International Nuclear Information System (INIS)

Lott, D.T.

1995-01-01

Tank Farms Operations must store/stage material and equipment until work packages are ready to work. Consumable materials are also required to be stored for routine and emergency work. Safety issues based on poor housekeeping and material deterioration due to weather damage has resulted from inadequate storage space. It has been determined that a storage building in close proximity to the Tank Farm work force would be cost effective. This document provides the design criteria for the design of the storage and staging buildings near 272AW and 272WA buildings

Decontamination and decommissioning criteria for use in design of new plutonium facilities

International Nuclear Information System (INIS)

Paschall, R.K.

1975-01-01

Decontamination and decommissioning (D and D) criteria were assembled for use in designing new plutonium facilities. These criteria were gathered from literature searches and visits to many plutonium facilities around the country. The recommendations of reports and experienced personnel were used. Since total D and D costs can be millions of dollars, improved designs to facilitate D and D will result in considerable savings in cost and time and will help to leave the site for unrestricted future use after D and D. Finally, better design will reduce hazards and improve safety during the D and D effort

Human Factors Design Criteria for Future Systems. FAADS Design Criteria Evolving from the Sgt. York Follow-On Evaluation 1

Science.gov (United States)

1989-05-01

and MIL-., TD -11172C. These are the most widely used documents providing human factors design criteria for the development of military systems through...4) 4bd 4)(.E c4- z - v -. r-f .r40 m 0 S -( OD Q) 0k .1 .o1 u .d 44). o- C.~) V QCf 44)) :0 J0 Al4 L .4Uv.-4 C4)LI.-44(U(E *4)4)( U . S- M 0 a *-P 4

Integrating Green Building Criteria Into Housing Design Processes Case Study: Tropical Apartment At Kebon Melati, Jakarta

Science.gov (United States)

Farid, V. L.; Wonorahardjo, S.

2018-05-01

The implementation of Green Building criteria is relatively new in architectural practice, especially in Indonesia. Consequently, the integration of these criteria into design process has the potential to change the design process itself. The implementation of the green building criteria into the conventional design process will be discussed in this paper. The concept of this project is to design a residential unit with a natural air-conditioning system. To achieve this purpose, the Green Building criteria has been implemented since the beginning of the design process until the detailing process on the end of the project. Several studies was performed throughout the design process, such as: (1) Conceptual review, where several professionally proved theories related to Tropical Architecture and passive design are used for a reference, and (2) Computer simulations, such as Computational Fluid Dynamics (CFD) and wind tunnel simulation, used to represent the dynamic response of the surrounding environment towards the building. Hopefully this paper may become a reference for designing a green residential building.

Fostering and Assessing Infographic Design for Learning: The Development of Infographic Design Criteria

Science.gov (United States)

Nuhoglu Kibar, Pinar; Akkoyunlu, Buket

2017-01-01

In this ever more digital and visual world, it has become more vital that students are encouraged to create content during the learning process through effective visualization of their knowledge. Infographics are an effective method for such visualization. The current study therefore proposes an infographic design rubric (IDR) as a criteria-based…

Design Criteria in Revitalizing Old Warehouse District on the Kalimas Riverbank Area of Surabaya City

Directory of Open Access Journals (Sweden)

Endang Titi Sunarti Darjosanjoto

2015-09-01

Full Text Available Neglected warehouse buildings along the Kalimas River have created a poor urban façade in terms of visual quality. However the city government is planning to encourage tourism activities that take advantage of Kalimas River and its surrounding environment. If there is no good plan in accordance with the concept of local identity for old city of Surabaya, it will reduce it as a tourist attraction. In reference to the issue above, design criteria needs to be compiled for revitalizing the old warehouse district, which is expected to revive the identity of this district and be able to support the city’s tourism. This study was conducted by recording field observations, and the data was analyzed using the character appraisal method. The character appraisal analysis method is presented in the form of street picture data, which is divided into determined segments. The results show that there are five components including place attachment, sustainable urban design, green open space design, ecological riverfront design, and activity support that should be considered in the revitalization of the warehouse district. Those components are divided into two parts: building and open space at the riverbank. There are 13 design criteria for building at the riverbank, while there are 14 design criteria for open space at the riverbank. These design criteria can enrich the warehouse district’s revitalization by improving the visual quality of the urban environment.Keywords: design criteria; warehouse district; riverbank; Surabaya; revitalization.

Designing Math Trails for Enhanced by Mobile Learning Realistic Mathematics Education in Primary Education

Directory of Open Access Journals (Sweden)

Georgios Fesakis

2018-05-01

Full Text Available Seeking a systematic combination of the pedagogical model of m-learning with the Realistic Mathematics Education (RME approach, this study concerns the use of math trail as a learning activity model that can take the advantages of mobile computing devices for the design of effective learning experiences in an authentic context. The paper presents the design and the case study of the first pilot implementation of a math trail, using mobile devices for primary school students. In this math trail, the students are guided, through a digital map, to a sequence of preselected sites of a park where they solve specially designed math problems using data from the environmental context. The students measure real objects’ dimensions either with conventional instruments or by measurement applications of their tablet. According to the findings of the study, students solved the puzzles by applying mathematical knowledge, discussion and collaboration. The students applied and reinforced their knowledge through an effective and engaging learning activity. Moreover, the students were puzzled about the differences of the measurements by conventional and digital instruments and this confusion triggered social negotiation. Further research is needed for a grounded theory development about m-learning design for RME.

Typical design/qualification acceptance criteria for newly installed pipelines and equipment components of VVER-type NPPs

International Nuclear Information System (INIS)

Masopust, R.

2003-01-01

This paper describes in general the typical design/qualification acceptance criteria and seismic acceptance criteria in particular that are applicable for important to safety newly installed pipelines and equipment components of VVER-type already existing NPPs, specifically during the design verification phase of this newly installed equipment. These criteria are currently used for VVER 440-213 and VVER 1000 NPPs in Czech Republic and in Slovakia. The similar criteria are also used in Hungary. (author)

Functional Design Criteria - plutonium stabilization and handling (PUSH) project W-460

International Nuclear Information System (INIS)

NELSON, D.W.

1999-01-01

This Functional Design Criteria (FDC) contains information to guide the design of the Stabilization and Packaging Equipment necessary to oxidize and package the remaining plutonium-bearing Special Nuclear Materials (SNM) currently in the Plutonium Finishing Plant (PFP) inventory. The FDC also guides the design of vault modifications to allow storage of 3013 packages of stabilized SNM for up to 50 years

Functional Design Criteria plutonium stabilization and handling (PUSH) project W-460

Energy Technology Data Exchange (ETDEWEB)

NELSON, D.W.

1999-09-02

This Functional Design Criteria (FDC) contains information to guide the design of the Stabilization and Packaging Equipment necessary to oxidize and package the remaining plutonium-bearing Special Nuclear Materials (SNM) currently in the Plutonium Finishing Plant (PFP) inventory. The FDC also guides the design of vault modifications to allow storage of 3013 packages of stabilized SNM for up to 50 years.

Evaluation of seismic criteria used in design of INEL facilities

International Nuclear Information System (INIS)

Young, G.A.

1977-01-01

This report provides the results of an independent evaluation of seismic studies that were made to establish the seismic acceleration levels and the response spectra used in the design of vital facilities at Idaho National Engineering Laboratory. A comparison of the procedures used to define the seismic acceleration values and response spectra at INEL with the requirements of the Nuclear Regulatory Commission showed that additional geologic studies would probably be required in order to fulfill NRC regulations. Recommendations are made on justifiable changes in the acceleration values and response spectra used at INEL. The geologic, geophysical, and seismological studies needed to provide a better understanding of the tectonic processes in the Snake River plains and the surrounding region are identified. Both potential and historical acceleration values are evaluated on a probability basis to permit a risk assessment approach to the design of new facilities and facility modifications. Studies conducted to develop seismic criteria for the design of the Loss of Fluid Test reactor and the New Waste Calcining Facility were selected as typical examples of criteria development previously used in the design of INEL facilities

77 FR 45282 - NRC Position on the Relationship Between General Design Criteria and Technical Specification...

Science.gov (United States)

2012-07-31

... Position on the Relationship Between General Design Criteria and Technical Specification Operability AGENCY... relationship between the general design criteria (GDC) for nuclear power plants and technical specification... Communications Branch, Division of Policy and Rulemaking, Office Nuclear Reactor Regulation, Mail Stop: OWFN-12-D...

Advanced Neutron Source radiological design criteria

International Nuclear Information System (INIS)

Westbrook, J.L.

1995-08-01

The operation of the proposed Advanced Neutron Source (ANS) facility will present a variety of radiological protection problems. Because it is desired to design and operate the ANS according to the applicable licensing standards of the Nuclear Regulatory Commission (NRC), it must be demonstrated that the ANS radiological design basis is consistent not only with state and Department of Energy (DOE) and other usual federal regulations, but also, so far as is practicable, with NRC regulations and with recommendations of such organizations as the Institute of Nuclear Power Operations (INPO) and the Electric Power Research Institute (EPRI). Also, the ANS radiological design basis is in general to be consistent with the recommendations of authoritative professional and scientific organizations, specifically the National Council on Radiation Protection and Measurements (NCRP) and the International Commission on Radiological Protection (ICRP). As regards radiological protection, the principal goals of DOE regulations and guidance are to keep occupational doses ALARA [as low as (is) reasonably achievable], given the current state of technology, costs, and operations requirements; to control and monitor contained and released radioactivity during normal operation to keep public doses and releases to the environment ALARA; and to limit doses to workers and the public during accident conditions. Meeting these general design objectives requires that principles of dose reduction and of radioactivity control by employed in the design, operation, modification, and decommissioning of the ANS. The purpose of this document is to provide basic radiological criteria for incorporating these principles into the design of the ANS. Operations, modification, and decommissioning will be covered only as they are affected by design

Development of a software tool and criteria evaluation for efficient design of small interfering RNA

International Nuclear Information System (INIS)

Chaudhary, Aparna; Srivastava, Sonam; Garg, Sanjeev

2011-01-01

Research highlights: → The developed tool predicted siRNA constructs with better thermodynamic stability and total score based on positional and other criteria. → Off-target silencing below score 30 were observed for the best siRNA constructs for different genes. → Immunostimulation and cytotoxicity motifs considered and penalized in the developed tool. → Both positional and compositional criteria were observed to be important. -- Abstract: RNA interference can be used as a tool for gene silencing mediated by small interfering RNAs (siRNA). The critical step in effective and specific RNAi processing is the selection of suitable constructs. Major design criteria, i.e., Reynolds's design rules, thermodynamic stability, internal repeats, immunostimulatory motifs were emphasized and implemented in the siRNA design tool. The tool provides thermodynamic stability score, GC content and a total score based on other design criteria in the output. The viability of the tool was established with different datasets. In general, the siRNA constructs produced by the tool had better thermodynamic score and positional properties. Comparable thermodynamic scores and better total scores were observed with the existing tools. Moreover, the results generated had comparable off-target silencing effect. Criteria evaluations with additional criteria were achieved in WEKA.

Criteria for design of the Yucca Mountain structures, systems and components for fault displacement

International Nuclear Information System (INIS)

Stepp, C.; Hossain, Q.; Nesbit, S.; Pezzopane, S.; Hardy, M.

1995-01-01

The DOE intends to design the Yucca Mountain high-level waste facility structures, systems and components (SSCs) for fault displacements to provide reasonable assurance that they will meet the preclosure safety performance objectives established by 10 CFR Part 60. To the extent achievable, fault displacement design of the facility will follow guidance provided in the NRC Staff Technical Position. Fault avoidance will be the primary design criterion, especially for spatially compact or clustered SSCs. When fault avoidance is not reasonably achievable, expected to be the case for most spatially extended SSCs, engineering design procedures and criteria or repair and rehabilitation actions, depending on the SSC's importance to safety, are provided. SSCs that have radiological safety importance will be designed for fault displacements that correspond to the hazard exceedance frequency equal to their established seismic safety performance goals. Fault displacement loads are generally localized and may cause local inelastic response of SSCs. For this reason, the DOE intends to use strain-based design acceptance criteria similar to the strain-based criteria used to design nuclear plant SSCs for impact and impulsive loads

Design Criteria for Bagless Transfer System (BTS) Packaging System

International Nuclear Information System (INIS)

RISENMAY, H.R.

2000-01-01

This document provides the criteria for the design and installation of a Bagless Transfer System (BTS); Blend, Sieve and Balance Equipment; and Supercritical Fluid Extraction System (SFE). The project consists of 3 major modules: (1) Bagless Transfer System (BTS) Module; (2) Blend, Sieve and Balance Equipment; and (3) Supercritical Fluid Extraction (SFE) Module

Design criteria for a self-actuated shutdown system to ensure limitation of core damage

International Nuclear Information System (INIS)

Deane, N.A.; Atcheson, D.B.

1981-09-01

Safety-based functional requirements and design criteria for a self-actuated shutdown system (SASS) are derived in accordance with LOA-2 success criteria and reliability goals. The design basis transients have been defined and evaluated for the CDS Phase II design, which is a 2550 MWt mixed oxide heterogeneous core reactor. A partial set of reactor responses for selected transients is provided as a function of SASS characteristics such as reactivity worth, trip points, and insertion times

Seismic design criteria used for electrical raceway systems in commercial nuclear power plants

International Nuclear Information System (INIS)

Summers, P.B.; Manrique, M.A.; Nelson, T.A.

1991-01-01

This paper summarizes some of the seismic design approaches, relevant technical issues and criteria used over the years for design of electrical raceway systems at commercial nuclear power plant facilities. The approaches used for design and endorsed by the NRC can be seen to be quite varied. In recent years, considerably more rigor has been required for raceway design, as well as for the level of design basis documentation produced. However, there has also been a willingness by the NRC to accept rational approaches based on testing, analytical results or experience data, provided proper justification is given. Such rational approaches can simplify the significant task of analysis, design and construction of miles of raceways and thousands of raceway supports. Summarizing past practice and identifying relevant technical issues are an important first step in formalizing up-to-date criteria for new raceway designs

Seismic design criteria for nuclear powerplants

International Nuclear Information System (INIS)

Jennings, P.C.; Guzman, R.A.

1975-01-01

There are three main aspects of the problem of selection of seismic design criteria for major projects such as nuclear power plants. These are the description of the appropriate level of shaking to be considered, usually given in the form of design spectra; the allowable response of the structure, usually specified in terms of allowable stresses and deflections; and the capability of the structure to dissipate energy, commonly given in the form of fractions of critical damping. In this presentation only the first of these features is examined, with particular application to nuclear power plants. Under these restrictions, the most important parts of the problem become the determination of the amplitude of the design spectra corresponding to the safe shutdown earthquake (SSE) and the question of whether the shape of the spectra recommended by Regulatory Guide 1.60 (U. S. Atomic Energy Commission, 1973) is appropriate for the particular application. In the course of working out the details of the approach, it was found useful to reexamine a number of concepts including the use of response spectra or peak values of ground motion parameters, the shape of the design spectra, problems in attenuation and scaling, and the use of motions on the ground surface or bedrock motions. There is nothing fundamentally new in the suggested approach, although some of the features may not have been applied to the problem of selecting design spectra for nuclear power plants in the way suggested. The approach is applied only to nuclear power plants but it is not limited to this application

STRUCTURAL DESIGN CRITERIA FOR TARGET/BLANKET SYSTEM COMPONENT MATERIALS FOR THE ACCELERATOR PRODUCTION OF TRITIUM PROJECT

Energy Technology Data Exchange (ETDEWEB)

W. JOHNSON; R. RYDER; P. RITTENHOUSE

2001-01-01

The design of target/blanket system components for the Accelerator Production of Tritium (APT) plant is dependent on the development of materials properties data specified by the designer. These data are needed to verify that component designs are adequate. The adequacy of the data will be related to safety, performance, and economic considerations, and to other requirements that may be deemed necessary by customers and regulatory bodies. The data required may already be in existence, as in the open technical literature, or may need to be generated, as is often the case for the design of new systems operating under relatively unique conditions. The designers' starting point for design data needs is generally some form of design criteria used in conjunction with a specified set of loading conditions and associated performance requirements. Most criteria are aimed at verifying the structural adequacy of the component, and often take the form of national or international standards such as the ASME Boiler and Pressure Vessel Code (ASME B and PV Code) or the French Nuclear Structural Requirements (RCC-MR). Whether or not there are specific design data needs associated with the use of these design criteria will largely depend on the uniqueness of the conditions of operation of the component. A component designed in accordance with the ASME B and PV Code, where no unusual environmental conditions exist, will utilize well-documented, statistically-evaluated developed in conjunction with the Code, and will not be likely to have any design data needs. On the other hand, a component to be designed to operate under unique APT conditions, is likely to have significant design data needs. Such a component is also likely to require special design criteria for verification of its structural adequacy, specifically accounting for changes in materials properties which may occur during exposure in the service environment. In such a situation it is common for the design criteria

Proceedings of the workshop on structural design criteria for HTR

International Nuclear Information System (INIS)

Breitbach, G.; Schubert, F.; Nickel, H.

1989-04-01

The papers demonstrate the status of high temperature reactor technology with regard to its realization in the nuclear power industry of various countries (FRG, USA, Japan) as well as to the development of safety rules in Germany. The design criteria for HTR could be presented. The criteria already determine definitely and almost completely the relevant requirements of the component rules. The informations include the technical boundary conditions with regard to safety, the metallic high temperature components, a particular section dealing with the reactor pressure vessel, especially with the prestressed concrete vessel, and the structural graphite components. (DG)

Guidelines for the development of natural phenomena hazards design criteria for surface facilities

International Nuclear Information System (INIS)

Nelson, T.A.; Hossain, Q.A.; Murray, R.C.

1992-01-01

This paper discusses the rationale behind the guidelines, criteria, and methodologies that are currently used for natural phenomena hazard design and evaluation of DOE nuclear and non-nuclear facilities. The bases for the performance goals and usage categories specified in UCRL-15910 are examined, and the sources of intentional conservatism in the analyses, design, and evaluation methods and criteria are identified. Outlines of recent developments/changes in DOE Orders related to Natural Phenomena hazard mitigation are also presented. Finally, the authors recommend the use of DOE methodologies as embodied in UCRL-15910 for design and evaluation of surface facilities of the high level nuclear waste repository site

Design criteria and fabrication in-pile test section of HANARO fuel test loop

Energy Technology Data Exchange (ETDEWEB)

Kim, J. Y.

1997-10-01

Safety state fuel test loop will be equipped in HANARO to obtain the development and betterments of advanced fuel and materials through the irradiation tests. The objective of this study is to determine the design criteria and technical specification of in-pile test section and to specify the manufacturing requirements of in-pile test section. HANARO fuel test loop was designed to meet the CANDU and PWR fuel testing and in-pile section will be manufactured and installed in HANARO. The design criteria and technical specification of in-pile test section could be used the fuel and materials design with for irradiation testing IPS of HANARO fuel test loop. This results will become guidances for the planning and programming of irradiation testing. (author). 12 refs., tabs., figs.

Functional design criteria 241-AP-102 Flexible Receiver System

International Nuclear Information System (INIS)

Roblyer, S.P.

1995-01-01

A mixer pump was installed in the 1.07 m (42-in.) riser of the central pump pit of tank 241-AP-102 to mitigate potential fluid separation particle sedimentation by mixing the tank's contents. The mixer pump performed this function until failure. Its removal is now necessary to meet possible tank content removal commitments or other corrective actions. The proposed removal procedure requires a flexible receiver that will provide a barrier to contamination during removal and transfer of the pump to the mixer pump storage container. This document describes the functional design criteria of the flexible receiver. These criteria include the functional and performance requirements of the flexible receiver as a barrier to contamination during normal conditions and contingencies and the instrumentation requirements

Development of a novel set of criteria to select methodology for designing product service systems

Directory of Open Access Journals (Sweden)

Tuananh Tran

2016-04-01

Full Text Available This paper proposes eight groups of twenty nine scoring criteria that can help designers and practitioners to compare and select an appropriate methodology for a certain problem in designing product service system (PSS. PSS has been researched for more than a decade and is now becoming more and more popular in academia as well as industry. Despite that fact, the adoption of PSS is still limited for its potential. One of the main reasons is that designing PSS itself is a challenge. Designers and developers face difficulties in choosing appropriate PSS design methodologies for their projects so that they can design effective PSS offerings. By proposing eight groups of twenty nine scoring criteria, this paper enables a “step by step” process to identify the most appropriate design methodology for a company’s PSS problem. An example is also introduced to illustrate the use of the proposed scoring criteria and provide a clear picture of how different design methodologies can be utilized at their best in terms of application.

Licensing topical report: interpretation of general design criteria for high-temperature gas-cooled reactors

International Nuclear Information System (INIS)

Orvis, D.D.; Raabe, P.H.

1980-01-01

This Licensing Topical Report presents a set of General Design Criteria (GDC) which is proposed for applicability to licensing of graphite-moderated, high-temperature gas-cooled reactors (HTGRs). Modifications as necessary to reflect HTGR characteristics and design practices have been made to the GDC derived for applicability to light-water-cooled reactors and presented in Appendix A of Part 50, Title 10, Code of Federal Regulations, including the Introduction, Definitions, and Criteria. It is concluded that the proposed set of GDC affords a better basis for design and licensing of HTGRs

Recording length criteria as applied in ultrasonic testing

International Nuclear Information System (INIS)

Fischer, E.; Kroening, M.; Schober, H.; Fischdick, H.

1983-01-01

An appreciable method used to assess the quality and integrity of safety-related components in light water reactors is the ultrasonic examination, in which case great importance is attributed to the criteria pertaining to recording length and permissible defect size. The development of the recording length criteria as applied when employing this method of examination is portrayed, the latter being based on the criteria which have proven themselves throughout long years of practice in the examination of conventional components. When taking these criteria into account the application of conventional ultrasonic techniques often leads to problems in the case of thick-walled components the reason being that indications are overrated. Taking the design of reactor components as the basic point of consideration, modified criteria are derived particularly when the size of discontinuities calculated by fracture mechanics analyses is taken into account. The introduction of new ultrasonic examination techniques such as, for example, focussed probes revealed that a considerably more realistic assessment is possible and consequently results in a reduction of unnecessary repairs. A comparison of the size of indications determined using conventional and analytical technqiues renders possible the anchoring of an intermediate stage in the evaluation of indications which is encompassed in the consideration of the bundle divergence. Thus a new concept is realized for the evaluation of ultrasonic indications detected in reactor components, which in the meantime has found its way into the associated regulatory guides. (orig.)

Design criteria for prestressed concrete pressure vessels for high temperature reactors

International Nuclear Information System (INIS)

Schimmelpfennig, K.

1991-01-01

This paper summarizes the work on design criteria for concrete structures of Prestressed Concrete Reactor Vessels (PCRVs), which has been carried out since 1984 by a couple of competent institutions. After some basic considerations on the safety demands on PCRVs, especially their Prestressed Concrete Structure (PCS), and the consequences for an elevated level of quality to be ensured by the design criteria, an impression is given, first, by what means a higher quality standard is gained with respect to selection of materials and specification of material data in comparison to the usual building industry and what kind of criteria on this behalf should be fixed in a PCRV code. As a further quality increasing feature, the specific demands on design analysis as practised according to the present state of science and as to be treated within a code are discussed. This concerns analyses for steady state and transient temperatures as well as stress and strain analyses for service and ultimate load conditions. It is outlined to what degree calculation models should be detailed, which includes statements about admissible idealizations. As a central topic the question is discussed in what way the ultimate load capacity has to be evaluated, thereby presenting results of some investigations pointing out the conditions under which the design is determined by the different kinds of ultimate load conditions. Finally, some reflections on the demands on monitoring the PCS behaviour during its lifetime and on several questions still to be answered in this field are expressed. (orig.)

Upgrading instrumentation and control in nuclear power plants. Design criteria

International Nuclear Information System (INIS)

Rodriguez Rodriguez, M.C.; Alvarez Menendez, A.

1997-01-01

The use of programmed digital technology in Protection, Control, Monitoring and Information Systems in new generation nuclear power plants, or the use of this technology to replace or upgrade existing systems based on wired analog instrumentation and electromechanical relays, has led to new international standards which establish new design requirements or adapt existing requirements to this technology. Additionally, both regulatory organisations and the industry are discussing the reliability of this technology, regarding common mode failures that may occur in redundant protection channels, due to the use of equipment and software with the same characteristics. The first part of this paper addresses the most important aspects of new international standards regarding classification criteria for I and C systems, equipment and functions, depending on their importance to safety and the design criteria applicable to each category. Special attention is drawn to requirements concerning software quality assurance and the design of new control rooms. The paper then goes on to discuss the different technical solutions being implemented, using equipment and software diversification, in order to prevent the possibility of common mode failures affecting the protection function. (Author)

Qualitative criteria and thresholds for low noise asphalt mixture design

Science.gov (United States)

Vaitkus, A.; Andriejauskas, T.; Gražulytė, J.; Šernas, O.; Vorobjovas, V.; Kleizienė, R.

2018-05-01

Low noise asphalt pavements are cost efficient and cost effective alternative for road traffic noise mitigation comparing with noise barriers, façade insulation and other known noise mitigation measures. However, design of low noise asphalt mixtures strongly depends on climate and traffic peculiarities of different regions. Severe climate regions face problems related with short durability of low noise asphalt mixtures in terms of considerable negative impact of harsh climate conditions (frost-thaw, large temperature fluctuations, hydrological behaviour, etc.) and traffic (traffic loads, traffic volumes, studded tyres, etc.). Thus there is a need to find balance between mechanical and acoustical durability as well as to ensure adequate pavement skid resistance for road safety purposes. Paper presents analysis of the qualitative criteria and design parameters thresholds of low noise asphalt mixtures. Different asphalt mixture composition materials (grading, aggregate, binder, additives, etc.) and relevant asphalt layer properties (air void content, texture, evenness, degree of compaction, etc.) were investigated and assessed according their suitability for durable and effective low noise pavements. Paper concluded with the overview of requirements, qualitative criteria and thresholds for low noise asphalt mixture design for severe climate regions.

Evaluation report(1): on design criteria for KALIMER metal fuel

International Nuclear Information System (INIS)

Hwang, Woan; Lee, Byoung Oon; Kim, Young Il

2001-04-01

Fuel rods, assembly ducts and their components in KALIMER should be designed to maintain the integrities and to assure their reliable in-reactor performances under the steady state and operational transient conditions which are included in design basis category. And the fuel system must be designed with enough engineering margin to minimize and prevent the failures under ab-normal operational condition, like an accident.In this report, some design limits and the criteria for the fuel assembly ducts for KALIMER are driven by evaluating the irradiation data of metallic fuel based on experimental data from ANL in USA, CRIEPI in Japan and RIAR in Russia

Evaluation report(1): on design criteria for KALIMER metal fuel

Energy Technology Data Exchange (ETDEWEB)

Hwang, Woan; Lee, Byoung Oon; Kim, Young Il

2001-04-01

Fuel rods, assembly ducts and their components in KALIMER should be designed to maintain the integrities and to assure their reliable in-reactor performances under the steady state and operational transient conditions which are included in design basis category. And the fuel system must be designed with enough engineering margin to minimize and prevent the failures under ab-normal operational condition, like an accident.In this report, some design limits and the criteria for the fuel assembly ducts for KALIMER are driven by evaluating the irradiation data of metallic fuel based on experimental data from ANL in USA, CRIEPI in Japan and RIAR in Russia.

Design criteria and principles for criticality detection and alarm systems

International Nuclear Information System (INIS)

Delafield, H.J.; Clifton, J.J.

1984-10-01

The report gives design principles and criteria for criticality detection and alarm systems based on earlier work and revised in the light of more recent experience. In particular, account is taken of the developments which have taken place in the field of radiation detection and in the understanding of the different types of criticality excursion. General guidance is given on the principles to apply in deciding upon the need for a criticality system. The characteristics of a criticality incident are described in terms of the minimum incident of concern, and the radiation field. Criteria for the threshold of detection of a criticality incident are then derived and the methods of detection considered. The selection and siting of criticality detectors is discussed, and design principles are given for alarm systems. Finally, testing and post-alarm procedures are outlined, followed by a summary of the principal recommendations. The supporting Appendices include a discussion of reliability and a summary of radiation detector characteristics. (author)

Criteria for the designation of radioactively contaminated land

International Nuclear Information System (INIS)

Titley, J.; Mobbs, S.; Burgess, P.; Hitchins, G.; Sinclair, P.

1999-01-01

This report examines the criteria for the designation of radioactively contaminated land. It should be read in conjunction with reference to another output from the project i.e. Environment Agency report, Technical Support Material for the Regulation of Radioactively Contaminated Land 1999. This report deals with the intervention on radioactively contaminated sites i.e. where no change of land use is anticipated and where the land has become contaminated as a result of previous land use and not current practices. (author)

Development of on-site accident criteria for waste transfer casks

International Nuclear Information System (INIS)

Uldrich, E.D.

1989-01-01

Removal of radioactive waste must withstand the scrutiny of the public and various regulatory offices. Currently, there is no standard accident criteria or methodology for intra-site shipments at the Idaho National Engineering Laboratory (INEL). Since the radioactive waste transfer casks only carry material within the INEL site boundaries and are not used for normal over-the-road transport, the requirements of 10 CFR 71 Packaging and Transportation of Radioactive Material, do not provide suitable requirements for cask design or safety analyses. The objective is to develop realistically conservative accident scenarios consistent with the limited uses at the INEL for which the cask is approved

An approach to development of structural design criteria for highly irradiated core components

International Nuclear Information System (INIS)

Nelson, D.V.

1980-01-01

The advent of the fast breeder reactor presents novel challenges in structural design and materials engineering. For instance, the core components of these reactors experience high energy neutron irradiation at elevated temperature, which causes significant time-dependent changes in material behaviour, such as a progressive loss of ductility. New structural design criteria are needed to extend elevated temperature design-by-analysis to account for these changes. Alloys best able to cope with the demands of the core operating environment are being explored and their structural behaviour characterized. The purpose of this paper is to illustrate an approach used in the development of core component structural design criteria. To do this, several design rules, plus brief rationale, from draft RDT Standards F9-7, -8 and -9 will be presented. These recently completed standards ('Structural Design Guidelines for Breeder Reactor Core Components') were prepared for the U.S. Department of Energy and represent a consensus among most organizations participating in the U.S. breeder program. (author)

Microseismic Monitoring Design Optimization Based on Multiple Criteria Decision Analysis

Science.gov (United States)

Kovaleva, Y.; Tamimi, N.; Ostadhassan, M.

2017-12-01

Borehole microseismic monitoring of hydraulic fracture treatments of unconventional reservoirs is a widely used method in the oil and gas industry. Sometimes, the quality of the acquired microseismic data is poor. One of the reasons for poor data quality is poor survey design. We attempt to provide a comprehensive and thorough workflow, using multiple criteria decision analysis (MCDA), to optimize planning micriseismic monitoring. So far, microseismic monitoring has been used extensively as a powerful tool for determining fracture parameters that affect the influx of formation fluids into the wellbore. The factors that affect the quality of microseismic data and their final results include average distance between microseismic events and receivers, complexity of the recorded wavefield, signal-to-noise ratio, data aperture, etc. These criteria often conflict with each other. In a typical microseismic monitoring, those factors should be considered to choose the best monitoring well(s), optimum number of required geophones, and their depth. We use MDCA to address these design challenges and develop a method that offers an optimized design out of all possible combinations to produce the best data acquisition results. We believe that this will be the first research to include the above-mentioned factors in a 3D model. Such a tool would assist companies and practicing engineers in choosing the best design parameters for future microseismic projects.

Design loads, loading combinations and structural acceptance criteria for BWR containments in the United States

International Nuclear Information System (INIS)

Edwards, N.W.

1979-01-01

The definition of loads, loading combinations, and structural acceptance criteria used for the design and evaluation of BWR containments in the Unites States has become much more comprehensive over the past decade. The Mark I pressure suppression containment vessels were designed for a static design pressure, a design temperature, dead load and static equivalent earthquake. The current Mark III containments are being designed to accommodate many more loads such as safety relief valve discharge loads, and suppression pool hydrodynamic loadings associated with the steam condensation phenomena as well as pressure and temperature transients for a range of pipe break sizes. Consistent with the more comprehensive definition of loads and loading combinations, the ASME Code presently establishes structural acceptance criteria with different margins of safety by the definition of Service Level Assignments A, B, C and D. Acting in a responsible manner, United States utilities are currently evaluating and modifying existing containment vessels to account for the more detailed load definition and structural acceptance criteria. (orig.)

Functional design criteria for the self-installing liquid observation well. Revision 2

International Nuclear Information System (INIS)

Parra, S.A.

1995-01-01

This document presents the functional design criteria for installing liquid observation wells (LOWs) into single-shell tanks containing ferrocyanide or organic wastes. The LOWs will be designed to accommodate the deployment of gamma, neutron, and electromagnetic induction probes and to interface with the existing tank structure and environment

Development of nuclear design criteria for neutron spallation sources

Energy Technology Data Exchange (ETDEWEB)

Sordo, F.; Abanades, A. [E.T.S. Industriales, Madrid Polytechnic University, UPM, J.Gutierrez Abascal, 2 -28006 Madrid (Spain)

2008-07-01

Spallation neutron sources allow obtaining high neutronic flux for many scientific and industrial applications. In recent years, several proposals have been made about its use, notably the European Spallation Source (ESS), the Japanese Spallation Source (JSNS) and the projects of Accelerator-Driven Subcritical reactors (ADS), particularly in the framework of EURATOM programs. Given their interest, it seems necessary to establish adequate design basis for guiding the engineering analysis and construction projects of this kind of installations. In this sense, all works done so far seek to obtain particular solutions to a particular design, but there has not been any general development to set up an engineering methodology in this field. In the integral design of a spallation source, all relevant physical processes that may influence its behaviour must be taken into account. Neutronic aspects (emitted neutrons and their spectrum, generation performance..), thermomechanical (energy deposition, cooling conditions, stress distribution..), radiological (spallation waste activity, activation reactions and residual heat) and material properties alteration due to irradiation (atomic displacements and gas generation) must all be considered. After analysing in a systematic manner the different options available in scientific literature, the main objective of this thesis was established as making a significant contribution to determine the limiting factors of the main aspects of spallation sources, its application range and the criteria for choosing optimal materials. To achieve this goal, a series of general simulations have been completed, covering all the relevant physical processes in the neutronic and thermal-mechanical field. Finally, the obtained criteria have been applied to the particular case of the design of the spallation source of subcritical reactors PDX-ADS and XT-ADS. These two designs, developed under the European R and D Framework Program, represent nowadays

Development of nuclear design criteria for neutron spallation sources

International Nuclear Information System (INIS)

Sordo, F.; Abanades, A.

2008-01-01

Spallation neutron sources allow obtaining high neutronic flux for many scientific and industrial applications. In recent years, several proposals have been made about its use, notably the European Spallation Source (ESS), the Japanese Spallation Source (JSNS) and the projects of Accelerator-Driven Subcritical reactors (ADS), particularly in the framework of EURATOM programs. Given their interest, it seems necessary to establish adequate design basis for guiding the engineering analysis and construction projects of this kind of installations. In this sense, all works done so far seek to obtain particular solutions to a particular design, but there has not been any general development to set up an engineering methodology in this field. In the integral design of a spallation source, all relevant physical processes that may influence its behaviour must be taken into account. Neutronic aspects (emitted neutrons and their spectrum, generation performance..), thermomechanical (energy deposition, cooling conditions, stress distribution..), radiological (spallation waste activity, activation reactions and residual heat) and material properties alteration due to irradiation (atomic displacements and gas generation) must all be considered. After analysing in a systematic manner the different options available in scientific literature, the main objective of this thesis was established as making a significant contribution to determine the limiting factors of the main aspects of spallation sources, its application range and the criteria for choosing optimal materials. To achieve this goal, a series of general simulations have been completed, covering all the relevant physical processes in the neutronic and thermal-mechanical field. Finally, the obtained criteria have been applied to the particular case of the design of the spallation source of subcritical reactors PDX-ADS and XT-ADS. These two designs, developed under the European R and D Framework Program, represent nowadays

Uncertainty Evaluation of a Postulated LBLOCA for APR+ using KINS Realistic Evaluation Methodology and MARS-KS

Energy Technology Data Exchange (ETDEWEB)

Hwang, Min Jeong; Marigomena, Ralph; Yoo, Tae Ho; Kim, Y. S.; Sim, S. K. [Environment and Energy Technology, Inc., Daejeon (Korea, Republic of); Bang, Young Seok [KINS, Daejeon (Korea, Republic of)

2014-05-15

As a part of the regulatory safety research, Korea Institute of Nuclear Safety(KINS) also developed a best estimate safety analysis regulatory audit code, MARS-KS, to realistically predict and better understand the physical phenomena of the design basis accidents. KINS improved uncertainty propagation methodology using MARS-KS and applied the improved uncertainty evaluation method for the Shinkori Units 3 and 4 LBLOC. This study is to evaluate the uncertainty propagation of a postulated LBLOCA and quantify the safety margin using KINS-REM and MARS-KS code for the APR+ (Advanced Pressurizer Reactor Plus) Standard Safety Analysis Report(SSAR) which is under regulatory review by the KINS for its design approval. KINS-REM LBLOCA realistic evaluation methodology was used for the regulatory assessment of the APR+ LBLOCA using MARS-KS to evaluate the uncertainty propagation of the uncertainty variables as well as to assess the safety margin during the limiting case of the APR+ double ended guillotine cold leg LBLOCA. Uncertainty evaluation for the APR+ LBLOCA shows that the reflood PCT with upper limit of 95% probability at 95% confidence level is 1363.2 K and is higher than the blowdown PCT95/95 of 1275.3 K. The result shows that the current evaluation of APR+ LBLOCA PCT is within the acceptance criteria of 1477 K ECCS.

Guidance for Developing Principal Design Criteria for Advanced (Non-Light Water) Reactors

Energy Technology Data Exchange (ETDEWEB)

Holbrook, Mark [Idaho National Lab. (INL), Idaho Falls, ID (United States); Kinsey, Jim [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-03-01

In July 2013, the US Department of Energy (DOE) and US Nuclear Regulatory Commission (NRC) established a joint initiative to address a key portion of the licensing framework essential to advanced (non-light water) reactor technologies. The initiative addressed the “General Design Criteria for Nuclear Power Plants,” Appendix A to10 Code of Federal Regulations (CFR) 50, which were developed primarily for light water reactors (LWRs), specific to the needs of advanced reactor design and licensing. The need for General Design Criteria (GDC) clarifications in non-LWR applications has been consistently identified as a concern by the industry and varied stakeholders and was acknowledged by the NRC staff in their 2012 Report to Congress1 as an area for enhancement. The initiative to adapt GDC requirements for non-light water advanced reactor applications is being accomplished in two phases. Phase 1, managed by DOE, consisted of reviews, analyses and evaluations resulting in recommendations and deliverables to NRC as input for NRC staff development of regulatory guidance. Idaho National Laboratory (INL) developed this technical report using technical and reactor technology stakeholder inputs coupled with analysis and evaluations provided by a team of knowledgeable DOE national laboratory personnel with input from individual industry licensing consultants. The DOE national laboratory team reviewed six different classes of emerging commercial reactor technologies against 10 CFR 50 Appendix A GDC requirements and proposed guidance for their adapted use in non-LWR applications. The results of the Phase 1 analysis are contained in this report. A set of draft Advanced Reactor Design Criteria (ARDC) has been proposed for consideration by the NRC in the establishment of guidance for use by non-LWR designers and NRC staff. The proposed criteria were developed to preserve the underlying safety bases expressed by the original GDC, and recognizing that advanced reactors may take

Argentine criteria on nuclear safety and emergencies: their impact on the Argos PHWR 380 design

International Nuclear Information System (INIS)

Gonzalez, A. J.

1988-01-01

This paper describes first the safety criteria of the Argentine regulatory authority with emphasis on the probabilistic safety criteria based on a limitation of individual risks. Then, it is presented a discussion on emergency criteria in relation to evacuation and relocation measures. Finally, the paper briefly describes the design of an Argentine offer for a safer heavy water reactor where these criteria are applied. 9 figs., 1 tab., 46 refs. (author)

Sustainable and safe design of footwear integrating ecological footprint and risk criteria.

Science.gov (United States)

Herva, Marta; Álvarez, Antonio; Roca, Enrique

2011-09-15

The ecodesign of a product implies that different potential environmental impacts of diverse nature must be taken into account considering its whole life cycle, apart from the general design criteria (i.e. technical, functional, ergonomic, aesthetic or economic). In this sense, a sustainability assessment methodology, ecological footprint (EF), and environmental risk assessment (ERA), were combined for the first time to derive complementary criteria for the ecodesign of footwear. Four models of children's shoes were analyzed and compared. The synthetic shoes obtained a smaller EF (6.5 gm(2)) when compared to the leather shoes (11.1 gm(2)). However, high concentrations of hazardous substances were detected in the former, even making the Hazard Quotient (HQ) and the Cancer Risk (CR) exceed the recommended safety limits for one of the synthetic models analyzed. Risk criteria were prioritized in this case and, consequently, the design proposal was discarded. For the other cases, the perspective provided by the indicators of different nature was balanced to accomplish a fairest evaluation. The selection of fibers produced under sustainable criteria and the reduction of the materials consumption was recommended, since the area requirements would be minimized and the absence of hazardous compounds would ensure safety conditions during the use stage. Copyright © 2011 Elsevier B.V. All rights reserved.

Advanced concepts, analysis approaches and criteria for nuclear piping system design

International Nuclear Information System (INIS)

Tang, H.T.; Tagart, S.W. Jr.; Tang, Y.K.

1992-01-01

Recent research in piping system design and analysis has resulted in advancements on damping values, independent support motion (ISM), static coefficient method, simplified inelastic method and ASME code criteria changes. In the support area, passive type of supports such as energy-absorbing device and gap stopper have been developed. These advancements provide bases for improved and cost-effective design of future nuclear piping systems. (author)

Development of biological criteria for the design of advanced hydropower turbines

Energy Technology Data Exchange (ETDEWEB)

Cada, Glenn F. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Coutant, Charles C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Whitney, Richard R. [Leavenworth, WA (United States)

1997-03-01

A review of the literature related to turbine-passage injury mechanisms suggests the following biological criteria should be considered in the design of new turbines: (1) pressure; (2) cavitation; (3) shear and turbulence; and (4) mechanical injury. Based on the study’s review of fish behavior in relation to hydropower facilities, it provides a number of recommendations to guide both turbine design and additional research.

Conceptual framework for potential implementations of multi criteria decision making (MCDM) methods for design quality assessment

NARCIS (Netherlands)

Harputlugil, T.; Prins, M.; Tanju Gültekin, A.; Ilker Topçu, Y.

2011-01-01

Architectural design can be considered as a process influenced by many stakeholders, each of which has different decision power. Each stakeholder might have his/her own criteria and weightings depending on his/her own perspective and role. Hence design can be seen as a multi-criteria decision making

Probabilistic Evaluation of Eurocode 5 Fire Design Criteria of a ...

African Journals Online (AJOL)

Structural reliability analysis for a three-hinge timber portal frame subjected to fire was undertaken. Eight modes of failure were identified for the frame and limit state function was formulated for each failure mode. The limit state functions were based on the Eurocode 5 design criteria. Uncertainties in the timber material ...

Implementation of decommissioning criteria in the conceptual design of the MRS facility

International Nuclear Information System (INIS)

Gross, D.L.; Wilcox, A.D.; Huang, S.

1986-01-01

The US Department of Energy (DOE) selected the Ralph M. Parsons Company (RMP) to prepare the conceptual design of the Monitored Retrievable Storage (MRS) Facility. The purpose of this facility is to consolidate and temporarily store spent fuel from civilian nuclear power plants. In addition, it will overpack, handle, and store high-level radioactive waste from non-defense related sources. The Functional Design Criteria (FDC) prepared by Pacific Northwest Laboratories, as well as 10 CFR 72, requires the facility to be designed for decommissioning, with provisions to facilitate decontamination of structures and equipment to minimize the volume of radioactive wastes and contaminated equipment at the time of decommissioning. Many problems associated with decommissioning a nuclear facility have been identified in recent years and the design for the MRS Facility presents a unique opportunity for RMP to implement decommissioning criteria into the conceptual design of a major nuclear facility. The provisions made in the design to facilitate decommissioning include good housekeeping during operations, controlled personnel access, access for equipment removal, equipment design, installed radiation monitors, adequate work space, installed decontamination systems and areas, control of all effluents, and operational documentation. These topics will be the major points of discussion for this paper

Study-design selection criteria in systematic reviews of effectiveness of health systems interventions and reforms: A meta-review.

Science.gov (United States)

Rockers, Peter C; Feigl, Andrea B; Røttingen, John-Arne; Fretheim, Atle; de Ferranti, David; Lavis, John N; Melberg, Hans Olav; Bärnighausen, Till

2012-03-01

At present, there exists no widely agreed upon set of study-design selection criteria for systematic reviews of health systems research, except for those proposed by the Cochrane Collaboration's Effective Practice and Organisation of Care (EPOC) review group (which comprises randomized controlled trials, controlled clinical trials, controlled before-after studies, and interrupted time series). We conducted a meta-review of the study-design selection criteria used in systematic reviews available in the McMaster University's Health Systems Evidence or the EPOC database. Of 414 systematic reviews, 13% did not indicate any study-design selection criteria. Of the 359 studies that described such criteria, 50% limited their synthesis to controlled trials and 68% to some or all of the designs defined by the EPOC criteria. Seven out of eight reviews identified at least one controlled trial that was relevant for the review topic. Seven percent of the reviews included either no or only one relevant primary study. Our meta-review reveals reviewers' preferences for restricting synthesis to controlled experiments or study designs that comply with the EPOC criteria. We discuss the advantages and disadvantages of the current practices regarding study-design selection in systematic reviews of health systems research as well as alternative approaches. Copyright © 2012. Published by Elsevier Ireland Ltd.

Physical criteria for the design and assessment of restoration schemes in the United Kingdom

International Nuclear Information System (INIS)

Humphries, R.N.; McQuire, G.E.

1994-01-01

The restoration of colliery wastes and open pit coal sites in the United Kingdom (UK) is undertaken according to a land use strategy plan and detailed specifications that have been agreed upon with the planning authorities. For two of the major land uses in the UK, agriculture and forestry, data on physical criteria (climate, site features and soils) are available to assist in the planning and design of land use strategies and specification of restoration treatments. Similar criteria could also be developed for the restoration of semi natural vegetation and habitats for landscape, wildlife, and amenity uses. Three examples are described illustrating the use of the physical criteria in the design of schemes, the specification of treatments, and the assessment of achievements

Considering dynamic friction and proper structural response in hydraulic load cases for realistic piping design

International Nuclear Information System (INIS)

Diesselhorst, T.; Diatschuk, P.; Schnellhammer, W.

2005-01-01

Concerning the design for hydraulic load cases there is always a sequence of fluid- and structural dynamic calculations, where the structural vibrations are induced by the time depending fluid forces. Therefore, in order to prevent excessive structural reactions, it is most important to avoid conservative fluid dynamic results. That refers to the maximum value of the pressure surge as well as to the damping of pressure oscillations. This is especially relevant in case of fluid-structure resonance. To meet these requirements the effect of dynamic wall friction was implemented in our fluid dynamic code. Thus, a more realistic damping behavior of the fluid forces was achieved. In the structural analysis code the damping of the pipe structure could be more accurate adapted to the real conditions. Additionally the local damping by viscous damper was included in the model. At supports now non-linear behavior like clearances can be simulated. The possibility of coupled calculation was installed to consider the effect of fluid structure interaction. The programmed effects are validated against measurement results from power plant systems. The favorable effects of the program improvements are demonstrated by typical examples. These included the realistic damping of pressure oscillations as well as a case of fluid-structure resonance. Additionally the effectiveness of the improved models of piping supports is demonstrated. (authors)

Sustainable and safe design of footwear integrating ecological footprint and risk criteria

International Nuclear Information System (INIS)

Herva, Marta; Alvarez, Antonio; Roca, Enrique

2011-01-01

Highlights: → The ecological footprint (EF) is a suitable screening indicator to assist the assessment of the sustainability of an ecodesign proposal. → The EF does not consider the risk derived from hazardous substances in its evaluation. → Environmental risk assessment (ERA) successfully complemented the evaluation of the EF providing safety criteria. → Options that exceeded the safety limits for Hazard Quotient and Cancer Risk where discarded, thus guaranteeing the protection of children. → Trade-offs among criteria could be established by the application of fuzzy logic techniques to derive an ecodesign index. - Abstract: The ecodesign of a product implies that different potential environmental impacts of diverse nature must be taken into account considering its whole life cycle, apart from the general design criteria (i.e. technical, functional, ergonomic, aesthetic or economic). In this sense, a sustainability assessment methodology, ecological footprint (EF), and environmental risk assessment (ERA), were combined for the first time to derive complementary criteria for the ecodesign of footwear. Four models of children's shoes were analyzed and compared. The synthetic shoes obtained a smaller EF (6.5 gm 2 ) when compared to the leather shoes (11.1 gm 2 ). However, high concentrations of hazardous substances were detected in the former, even making the Hazard Quotient (HQ) and the Cancer Risk (CR) exceed the recommended safety limits for one of the synthetic models analyzed. Risk criteria were prioritized in this case and, consequently, the design proposal was discarded. For the other cases, the perspective provided by the indicators of different nature was balanced to accomplish a fairest evaluation. The selection of fibers produced under sustainable criteria and the reduction of the materials consumption was recommended, since the area requirements would be minimized and the absence of hazardous compounds would ensure safety conditions during the

Sustainable and safe design of footwear integrating ecological footprint and risk criteria

Energy Technology Data Exchange (ETDEWEB)

Herva, Marta [Sustainable Processes and Products Engineering Group, Department of Chemical Engineering, University of Santiago de Compostela, Campus Vida, 15705 Santiago de Compostela (Spain); Alvarez, Antonio [Industrias de Diseno Textil, S.A., Edificio Inditex, Av. de la Diputacion s/n, Poligono de Sabon, 15142 Arteixo - A Coruna (Spain); Roca, Enrique, E-mail: enrique.roca@usc.es [Sustainable Processes and Products Engineering Group, Department of Chemical Engineering, University of Santiago de Compostela, Campus Vida, 15705 Santiago de Compostela (Spain)

2011-09-15

Highlights: {yields} The ecological footprint (EF) is a suitable screening indicator to assist the assessment of the sustainability of an ecodesign proposal. {yields} The EF does not consider the risk derived from hazardous substances in its evaluation. {yields} Environmental risk assessment (ERA) successfully complemented the evaluation of the EF providing safety criteria. {yields} Options that exceeded the safety limits for Hazard Quotient and Cancer Risk where discarded, thus guaranteeing the protection of children. {yields} Trade-offs among criteria could be established by the application of fuzzy logic techniques to derive an ecodesign index. - Abstract: The ecodesign of a product implies that different potential environmental impacts of diverse nature must be taken into account considering its whole life cycle, apart from the general design criteria (i.e. technical, functional, ergonomic, aesthetic or economic). In this sense, a sustainability assessment methodology, ecological footprint (EF), and environmental risk assessment (ERA), were combined for the first time to derive complementary criteria for the ecodesign of footwear. Four models of children's shoes were analyzed and compared. The synthetic shoes obtained a smaller EF (6.5 gm{sup 2}) when compared to the leather shoes (11.1 gm{sup 2}). However, high concentrations of hazardous substances were detected in the former, even making the Hazard Quotient (HQ) and the Cancer Risk (CR) exceed the recommended safety limits for one of the synthetic models analyzed. Risk criteria were prioritized in this case and, consequently, the design proposal was discarded. For the other cases, the perspective provided by the indicators of different nature was balanced to accomplish a fairest evaluation. The selection of fibers produced under sustainable criteria and the reduction of the materials consumption was recommended, since the area requirements would be minimized and the absence of hazardous compounds would

Failsafe design criteria for computer based reactor protection systems

International Nuclear Information System (INIS)

Keats, A.B.

1980-01-01

The design criteria proposed are an extrapolation of the failsafe mode of operation used in the UK in hardwired reactor protection systems. This is achieved by making the operational condition of the reactor dependent upon an energetic state of the protection system components. An important objective of the proposed design criteria is to eliminate, or at least to minimize, the need for a failure-mode-and-effect-analysis (FMEA) of the computer software. This demands some well defined but simple constraints upon the way in which data are stored in the computers, but the objective is achieved almost entirely by hardware properties of the system. The first of these is the systematic use of hardwired test inputs which cause transient excursions into the tripped state in a uniquely ordered but easily recognizable sequence. The second is the use of hardwired pattern recognition logic which generates a dynamic healthy stimulus for the shutdown actuators only in response to the unique sequence formed by the hardwired input signal pattern. It therefore detects abnormal states of any of the system inputs, software errors, wiring errors and hardware failures. This hardwired logic is conceptually simple, failsafe, and is amenable to simple FMEA. (U.K.)

Realistic Real-Time Outdoor Rendering in Augmented Reality

Science.gov (United States)

Kolivand, Hoshang; Sunar, Mohd Shahrizal

2014-01-01

Realistic rendering techniques of outdoor Augmented Reality (AR) has been an attractive topic since the last two decades considering the sizeable amount of publications in computer graphics. Realistic virtual objects in outdoor rendering AR systems require sophisticated effects such as: shadows, daylight and interactions between sky colours and virtual as well as real objects. A few realistic rendering techniques have been designed to overcome this obstacle, most of which are related to non real-time rendering. However, the problem still remains, especially in outdoor rendering. This paper proposed a much newer, unique technique to achieve realistic real-time outdoor rendering, while taking into account the interaction between sky colours and objects in AR systems with respect to shadows in any specific location, date and time. This approach involves three main phases, which cover different outdoor AR rendering requirements. Firstly, sky colour was generated with respect to the position of the sun. Second step involves the shadow generation algorithm, Z-Partitioning: Gaussian and Fog Shadow Maps (Z-GaF Shadow Maps). Lastly, a technique to integrate sky colours and shadows through its effects on virtual objects in the AR system, is introduced. The experimental results reveal that the proposed technique has significantly improved the realism of real-time outdoor AR rendering, thus solving the problem of realistic AR systems. PMID:25268480

Realistic real-time outdoor rendering in augmented reality.

Directory of Open Access Journals (Sweden)

Hoshang Kolivand

Full Text Available Realistic rendering techniques of outdoor Augmented Reality (AR has been an attractive topic since the last two decades considering the sizeable amount of publications in computer graphics. Realistic virtual objects in outdoor rendering AR systems require sophisticated effects such as: shadows, daylight and interactions between sky colours and virtual as well as real objects. A few realistic rendering techniques have been designed to overcome this obstacle, most of which are related to non real-time rendering. However, the problem still remains, especially in outdoor rendering. This paper proposed a much newer, unique technique to achieve realistic real-time outdoor rendering, while taking into account the interaction between sky colours and objects in AR systems with respect to shadows in any specific location, date and time. This approach involves three main phases, which cover different outdoor AR rendering requirements. Firstly, sky colour was generated with respect to the position of the sun. Second step involves the shadow generation algorithm, Z-Partitioning: Gaussian and Fog Shadow Maps (Z-GaF Shadow Maps. Lastly, a technique to integrate sky colours and shadows through its effects on virtual objects in the AR system, is introduced. The experimental results reveal that the proposed technique has significantly improved the realism of real-time outdoor AR rendering, thus solving the problem of realistic AR systems.

Design criteria for the light duty utility arm system end effectors

International Nuclear Information System (INIS)

Pardini, A.F.

1995-01-01

This document provides the criteria for the design of end effectors that will be used as part of the Light Duty Utility Arm (LDUA) System. The LDUA System consists of a deployment vehicle, a vertical positioning mast, a light duty multi-axis robotic arm, a tank riser interface and confinement, a tool interface plate, a control system, and an operations control trailer. The criteria specified in this document will apply to all end effector systems being developed for use on or with the LDUA system at the Hanford site. The requirement stipulated in this document are mandatory

Design criteria and design basis for the 100-HR-3 and 100-KR-4 pump-and-treat projects

International Nuclear Information System (INIS)

McKinley, W.S.; Winters, J.N.

1996-06-01

The 100-HR-3 and 100-KR-4 Operable Units are located in the 100 Area at the Hanford Site in Richland, Washington. The document describes the project objectives and design criteria to be used for the 100-HR-3 and 100-KR-4 groundwater pump-and-treat design activities

Realistic full wave modeling of focal plane array pixels.

Energy Technology Data Exchange (ETDEWEB)

Campione, Salvatore [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States). Electromagnetic Theory Dept.; Warne, Larry K. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States). Electromagnetic Theory Dept.; Jorgenson, Roy E. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States). Electromagnetic Theory Dept.; Davids, Paul [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States). Applied Photonic Microsystems Dept.; Peters, David W. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States). Applied Photonic Microsystems Dept.

2017-11-01

Here, we investigate full-wave simulations of realistic implementations of multifunctional nanoantenna enabled detectors (NEDs). We focus on a 2x2 pixelated array structure that supports two wavelengths of operation. We design each resonating structure independently using full-wave simulations with periodic boundary conditions mimicking the whole infinite array. We then construct a supercell made of a 2x2 pixelated array with periodic boundary conditions mimicking the full NED; in this case, however, each pixel comprises 10-20 antennas per side. In this way, the cross-talk between contiguous pixels is accounted for in our simulations. We observe that, even though there are finite extent effects, the pixels work as designed, each responding at the respective wavelength of operation. This allows us to stress that realistic simulations of multifunctional NEDs need to be performed to verify the design functionality by taking into account finite extent and cross-talk effects.

Realistic and efficient 2D crack simulation

Science.gov (United States)

Yadegar, Jacob; Liu, Xiaoqing; Singh, Abhishek

2010-04-01

Although numerical algorithms for 2D crack simulation have been studied in Modeling and Simulation (M&S) and computer graphics for decades, realism and computational efficiency are still major challenges. In this paper, we introduce a high-fidelity, scalable, adaptive and efficient/runtime 2D crack/fracture simulation system by applying the mathematically elegant Peano-Cesaro triangular meshing/remeshing technique to model the generation of shards/fragments. The recursive fractal sweep associated with the Peano-Cesaro triangulation provides efficient local multi-resolution refinement to any level-of-detail. The generated binary decomposition tree also provides efficient neighbor retrieval mechanism used for mesh element splitting and merging with minimal memory requirements essential for realistic 2D fragment formation. Upon load impact/contact/penetration, a number of factors including impact angle, impact energy, and material properties are all taken into account to produce the criteria of crack initialization, propagation, and termination leading to realistic fractal-like rubble/fragments formation. The aforementioned parameters are used as variables of probabilistic models of cracks/shards formation, making the proposed solution highly adaptive by allowing machine learning mechanisms learn the optimal values for the variables/parameters based on prior benchmark data generated by off-line physics based simulation solutions that produce accurate fractures/shards though at highly non-real time paste. Crack/fracture simulation has been conducted on various load impacts with different initial locations at various impulse scales. The simulation results demonstrate that the proposed system has the capability to realistically and efficiently simulate 2D crack phenomena (such as window shattering and shards generation) with diverse potentials in military and civil M&S applications such as training and mission planning.

Studies on design principles and criteria of fuels and graphites for experimental multi-purpose very high temperature reactor

International Nuclear Information System (INIS)

Arai, Taketoshi; Sato, Sadao; Tani, Yutaro

1977-12-01

Design principles and criteria of fuels and graphites have been studied to determine the main design parameters of a reference core MARK-III of the Experimental Multi-purpose Very High Temperature Reactor. The present status of research and development for HTGR fuels and graphites is reviewed from a standpoint of their integrity and safety aspects, and is compared to the specific design requirements for the VHTR fuels and graphites. Consequently, reasonable materials specifications, safety criteria and design analysis methods are presented for coated fuel particle, fuel compact, graphite sleeve, core support graphite and neutron absorber material. These design principles and criteria will be refined by further experimental investigations. (auth.)

Putting a Realistic Theory of Mind into Agency Theory

DEFF Research Database (Denmark)

Foss, Nicolai Juul; Stea, Diego

2014-01-01

Agency theory is one of the most important foundational theories in management research, but it rests on contestable cognitive assumptions. Specifically, the principal is assumed to hold a perfect (correct) theory regarding some of the content of the agent's mind, while he is entirely ignorant...... concerning other such content. More realistically, individuals have some limited access to the minds of others. We explore the implications for classical agency theory of realistic assumptions regarding the human potential for interpersonal sensemaking. We discuss implications for the design and management...

ITER structural design criteria and their extension to advanced reactor blankets

International Nuclear Information System (INIS)

Majumdar, S.; Kalinin, G.

2000-01-01

Applications of the recent ITER structural design criteria (ISDC) are illustrated by two components. First, the low-temperature-design rules are applied to copper alloys that are particularly prone to irradiation embrittlement at relatively low fluences at certain temperatures. Allowable stresses are derived and the impact of the embrittlement on allowable surface heat flux of a simple first-wall/limiter design is demonstrated. Next, the high-temperature-design rules of ISDC are applied to evaporation of lithium and vapor extraction (EVOLVE), a blanket design concept currently being investigated under the US Advanced Power Extraction (APEX) program. A single tungsten first-wall tube is considered for thermal and stress analyses by finite-element method

Vision-based methodology for collaborative management of qualitative criteria in design

DEFF Research Database (Denmark)

Tollestrup, Christian

2006-01-01

establishes a field of tension that summarises the abstract criteria and pinpoints the desired uniqueness of the product. The Interaction Vision allows the team members to design the behaviour of the product without deciding on physical features, thus focusing on the cognitive aspects of the product...

Monitoring programmes for internal exposure: designing criteria

International Nuclear Information System (INIS)

Rojo, Ana M.; Gomez Parada, Ines.

2007-01-01

The purpose of this document is to offer guidance for the decision whether a monitoring programme is required and how it should be designed. It can be also used as a tool for making the standing programmes consistent with the most recent publications on internal dosimetry, such as ISO 20553 'Monitoring of workers occupationally exposed to a risk of internal contamination with radioactive material', specific publications of the IAEA and ICRP, and including the conclusions of the OMINEX Project ('Optimisation of Monitoring for Internal Exposures') and IDEAS Project. It is established that the general purpose of the monitoring is verify that each worker is protected adequately against risks from radionuclide intakes and document that the protection complies with legal requirements. The criteria for a particular monitoring programme designing is based on the magnitude of the probable intake and the possibility of detecting a significant event when it occurs. So, the risk assessment for each work process must be evaluated and each worker is classified accordingly. This classification implies the acceptance of reference effective dose values (1 y 6 mSv/y ). (author) [es

General design criteria for diesel-generator sets for nuclear power plants

International Nuclear Information System (INIS)

Rangarao, G.

1975-01-01

The design criteria for diesel-generators for nuclear power plants are examined. Applicable standards, loading, design performance, and characteristics to be considered in the selection of diesel-generator set and its auxiliary system are discussed. Also, engineered safety features loads together with loss of power safe shutdown loads and their starting sequence, analysis of voltage and frequency response and the diesel-generator ability to start various load blocks successfully to meet the reactor emergency core cooling requirements are discussed

The 1994 Forum on Appropriate Criteria and Methods for Seismic Design of Nuclear Piping

International Nuclear Information System (INIS)

Slagis, G.C.

1995-01-01

A record of the 1994 Forum on Appropriate Criteria and Methods for Seismic Design of Nuclear Piping is provided. The focus of the forum was the design-by-rule method for seismic design of piping. Issues such as acceptance criteria, ductility considerations, demonstration of margin, training, verification and costs were discussed. The use of earthquake experience data, including the recent Northridge earthquake, to justify a design-by-rule method was explored. The majority of the participants felt there are not significant advantages to developing a design-by-rule approach for new plant design. One major disadvantage was considered by many to be training. Extensive training will be required to properly implement a design-by-rule approach. Verification of designs was considered by the majority to be equally important for design-by-rule as for design-by-analysis. If a design-by-rule method is going to be effective, the method will have to be based on ductility considerations (UBC approach). A significant issue will be justification of seismic margins with liberal rules. The UBC approach is being questioned by some because of the recent structural cracking problems in the Northridge earthquake

Automated Finger Spelling by Highly Realistic 3D Animation

Science.gov (United States)

Adamo-Villani, Nicoletta; Beni, Gerardo

2004-01-01

We present the design of a new 3D animation tool for self-teaching (signing and reading) finger spelling the first basic component in learning any sign language. We have designed a highly realistic hand with natural animation of the finger motions. Smoothness of motion (in real time) is achieved via programmable blending of animation segments. The…

Seismic design criteria for the Clinch River Breeder Reactor Plant

International Nuclear Information System (INIS)

Morrone, A.; Bitner, J.L.; Sigal, G.B.

1975-01-01

The general criteria for seismic resistant design for structures, systems and components of the Clinch River Breeder Reactor Plant (CRBRP) are presented and discussed. Site dependency of the maximum ground accelerations for the Operating Basis Earthquake and the Safe Shutdown Earthquake is described from the viewpoint of historical records and geological and seismological studies for the CRBRP site. The respective ground response spectra are derived by normalization of the latest AEC Regulatory standard shapes to these maximum ground accelerations. Modeling and analytical techniques and requirements are given. In addition, loading conditions and categories, loading combinations, earthquake direction effects and allowable damping values are defined. A discussion of the testing criteria which considers both single and multiple frequency test motions, and basic test procedures for single frequency sine beat testing is presented. (U.S.)

Seismic design criteria and their application to major hazard plant within the United Kingdom

International Nuclear Information System (INIS)

Alderson, M.A.H.G.

1982-12-01

The nature of seismic motions and the implications are briefly described and the development of seismic design criteria for nuclear power plants in various countries is described including possible future developments. The seismicity of the United Kingdom is briefly reviewed leading to the present position on seismic design criteria for nuclear power plants within the United Kingdom. Damage from past destructive earthquakes is reviewed and the existing codes of practice and standards are described. Finally the effect of earthquakes on major hazard plant is discussed in general terms including the seismic analysis of a typical plant item. (author)

Hydraulic Design Criteria for Spacer Grids of Nuclear Fuel Element

International Nuclear Information System (INIS)

Juanico, Luis; Brasnarof, Daniel

2000-01-01

In this paper a hydraulic model for calculating the pressure drop on the CARA spacer grids is extended.This model is validated and feedback from experimental hydraulic test performed in a low pressure loop.The importance of the spacer grid geometric parameter (that is, its thickness and length, the number and kind of their fix spacer), developing hydraulic design criteria for spacer grid on fuel element

The application of the multi-criteria analysis in evaluating of the road designs

Directory of Open Access Journals (Sweden)

Kuzović Ljubiša T.

2015-01-01

Full Text Available The analysis of the suitability of applying multi-criteria ranking of road design variants places the emphasis on the danger of fixing the ranking results, by the impact of subjective factors, in the process of determining relevant criteria and their relative weights. This danger is illustrated using two real examples. In the first example, subjective factors did not have a decisive influence since all of the most significant technical exploitation economic and ecological indicators, determined in the appropriate study and project documentation, were taken into account while determining relevant criteria and their relative weights. In the second example, subjective factors had a more decisive influence since all of the most significant technical exploitation economic and ecological indicators, determined in the appropriate study and project documentation, were not taken into account while determining relevant criteria and their relative weights.

The constraints satisfaction problem approach in the design of an architectural functional layout

Science.gov (United States)

Zawidzki, Machi; Tateyama, Kazuyoshi; Nishikawa, Ikuko

2011-09-01

A design support system with a new strategy for finding the optimal functional configurations of rooms for architectural layouts is presented. A set of configurations satisfying given constraints is generated and ranked according to multiple objectives. The method can be applied to problems in architectural practice, urban or graphic design-wherever allocation of related geometrical elements of known shape is optimized. Although the methodology is shown using simplified examples-a single story residential building with two apartments each having two rooms-the results resemble realistic functional layouts. One example of a practical size problem of a layout of three apartments with a total of 20 rooms is demonstrated, where the generated solution can be used as a base for a realistic architectural blueprint. The discretization of design space is discussed, followed by application of a backtrack search algorithm used for generating a set of potentially 'good' room configurations. Next the solutions are classified by a machine learning method (FFN) as 'proper' or 'improper' according to the internal communication criteria. Examples of interactive ranking of the 'proper' configurations according to multiple criteria and choosing 'the best' ones are presented. The proposed framework is general and universal-the criteria, parameters and weights can be individually defined by a user and the search algorithm can be adjusted to a specific problem.

Prestressed concrete reactor vessels: review of design and failure criteria

International Nuclear Information System (INIS)

Endebrock, E.G.

1975-03-01

The design and failure criteria of prestressed concrete reactor vessels (PCRVs) are reviewed along with the analysis methods. The mechanical properties of concrete under multiaxial stresses are not adequately quantified or described to permit an accurate analysis of a PCRV. Structural analysis of PCRVs almost universally utilizes a finite element which encounters difficulties in numerical solution of the governing equations and in treatment of fractured elements. (U.S.)

Design criteria of primary coolant chemistry in SMART-P

International Nuclear Information System (INIS)

Choi, Byung Seon; Kim, Ah Young; Kim, Seong Hoon; Yoon, Ju Hyeon; Zee, Sung Qunn

2005-01-01

SMART-P differs significantly from commercially designed PWRs. Materials inventories used in SMART-P differ from that at PWRs. All surfaces of the primary circuit with the primary coolant are either made from or plated with stainless steel. The material of steam generator (SG) is also different from that of the standard material of the commercially operating PWRs: titanium alloy for the steam generator tubes. Also, SMART-P primary coolant technology differs from that in PWRs: ammonia is used as a pH raising agent and hydrogen formed due to radiolytic processes is kept in specific range by ammonia dosing. Nevertheless, main objectives of the SMART-P primary coolant are the same as at PWRs: to assure primary system pressure boundary integrity, fuel cladding integrity and to minimize out-of-core radiation buildup. The objective of this work is to introduce the design criteria for the primary water chemistry for SMART-P from the viewpoint of the system characteristics and the chemical design concept

Kinetic and empirical design criteria for constructed wetlands

International Nuclear Information System (INIS)

Nix, P.G.; Gulley, J.R.

1995-01-01

A study was conducted to demonstrate the capabilities of wetlands as long-term, self-sustaining natural systems for the treatment of large quantities of waste water released from tailings ponds after mine abandonment. Constructed wetlands were built and planted with aquatic plants. The experimental design included three replicate trenches for each of two treatment systems. The objective of the research was to assess the optimum contaminant loading rates which would result in an acceptable quality of the effluent water. Using empirical data (i.e., hydrocarbon loading rates versus effluent quality), the optimal range of hydrocarbon loading was 5 to 25 gTEH/m 2/ month. Using more conservative kinetic data (i.e. microbial mineralization rates), the range of optimal treatment effectiveness was 9.6 to 13.2 gTEH/m 2/ month. The two design criteria methodologies were calculated using two independent analytical methods. The similarity in results was judged to be a confirmation of their accuracy. 20 refs., 5 figs

Report of the workshop on realistic SSC lattices

International Nuclear Information System (INIS)

1985-10-01

A workshop was held at the SSC Central Design Group from May 29 to June 4, 1985, on topics relating to the lattice of the SSC. The workshop marked a shift of emphasis from the investigation of simplified test lattices to the development of a realistic lattice suitable for the conceptual design report. The first day of the workshop was taken up by reviews of accelerator system requirements, of the reference design solutions for these requirements, of lattice work following the reference design, and of plans for the workshop. The work was divided among four working groups. The first, chaired by David Douglas, concerned the arcs of regular cells. The second group, which studied the utility insertions, was chaired by Beat Leemann. The third group, under David E. Johnson, concerned itself with the experimental insertions, dispersion suppressors, and phase trombones. The fourth group, responsible for global lattice considerations and the design of a new realistic lattice example, was led by Ernest Courant. The papers resulting from this workshop are roughly divided into three sets: those relating to specific lattice components, to complete lattices, and to other topics. Among the salient accomplishments of the workshop were additions to and optimization of lattice components, especially those relating to lattices using 1-in-1 magnets, either horizontally or vertically separated, and the design of complete lattice examples. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database

Waste Receiving and Processing Facility, Module 1: Volume 7, Project design criteria

International Nuclear Information System (INIS)

1992-03-01

This Project Design Criteria document for the WRAP facility at the Hanford Site is presented within a systems format. The WRAP Module 1 facility has been categorized into eight (8) engineering systems for design purposes. These systems include: receiving, shipping and storage, nondestructive assay/nondestructive examination (NDA/NDE), waste process, internal transportation, building, heating ventilation and air conditioning (HVAC), process control, and utilities. Within each system section of this document, the system-specific requirements are identified. The scope of the system is defined, the design goals are identified and the functional requirements are detailed

Design criteria for the light duty utility arm system end effectors

International Nuclear Information System (INIS)

Pardini, A.F.; Kiebel, G.R.

1995-12-01

The purpose of this document is to provide criteria for the design of end effectors that will be used as part of the Light Duty Utility Arm (LDUA) System. Actual component design, fabrication, testing, and inspection will be performed by various DOE laboratories, industry, and academia. This document augments WHC-SD-TD-FRD-003, 'Functions and Requirements for the Light Duty Utility Arm Integrated System' (F). All requirements dictated in the F shall also be applicable in this document. Whenever conflicts arise between this document and the F, this document shall take precedence

Packaging design criteria (onsite) project W-520 immobilized low-activity waste transportation system

International Nuclear Information System (INIS)

BOEHNKE, W.M.

2001-01-01

A plan is currently in place to process the high-level radioactive wastes that resulted from uranium and plutonium recovery operations from Spent Nuclear Fuel at the Hanford Site, Richland, Washington. Currently, millions of gallons of high-level radioactive waste in the form of liquids, sludges, and saltcake are stored in many large underground tanks onsite. This waste will be processed and separated into high-level and low-activity fractions. Both fractions will then be vitrified (i.e., blended with molten borosilicate glass) in order to encapsulate the toxic radionuclides. The immobilized low-activity waste (ILAW) glass will be poured into LAW canisters, allowed to cool and harden to solid form, sealed by welding, and then transported to a double-lined trench in the 200 East Area for permanent disposal. This document presents the packaging design criteria (PDC) for an onsite LAW transportation system, which includes the ILAW canister, ILAW package, and transport vehicle and defines normal and accident conditions. This PDC provides the basis for the ILAW onsite transportation system design and fabrication and establishes the transportation safety criteria that the design will be evaluated against in the Package Specific Safety Document (PSSD). It provides the criteria for the ILAW canister, cask and transport vehicles and defines normal and accident conditions. The LAW transportation system is designed to transport stabilized waste from the vitrification facility to the ILAW disposal facility developed by Project W-520. All ILAW transport will take place within the 200 East Area (all within the Hanford Site)

Healthcare Building Sustainability Assessment tool - Sustainable Effective Design criteria in the Portuguese context

International Nuclear Information System (INIS)

Castro, Maria de Fátima; Mateus, Ricardo; Bragança, Luís

2017-01-01

Tools and methods to improve current practices and quality in the healthcare building sector are necessary to support decision-making at different building life cycle phases. Furthermore, Healthcare Building Sustainability Assessment (HBSA) Methods are based on criteria organised into different levels, such as categories and indicators. These criteria highlight aspects of significant importance when designing and operating a sustainable healthcare building. To bring more objectivity to the sustainability assessments, the standardisation bodies (CEN and ISO) proposed core indicators that should be used in the evaluation of the environmental, societal and economic performances of buildings. Nevertheless, relying on state of the art analysis, it is possible to conclude that there are aspects of major importance for the operation of healthcare buildings that are not considered in the HBSA methods. Thus, the aim of this paper is to discuss the context of sustainability assessment methods in the field of healthcare buildings and to present a proposal for the incorporation of Sustainable-Effective Design (SED) criteria in a new HBSA method. The used research method is innovative since in the development of the list of sustainability criteria it considers the opinion of main healthcare buildings' stakeholders, the existing healthcare assessment methods and the ISO and CEN standardisation works in the field of the methods to assess the sustainability of construction works. As a result, the proposed method is composed of fifty-two sustainability indicators that cover the different dimensions of the sustainability concept to support decision making during the design of a new or retrofitted healthcare building in urban areas. - Highlights: •A new system to assess the sustainability of healthcare buildings is presented. •We propose a method to develop the list of sustainability indicators for hospitals. •We propose a new concept – Sustainable-Effective Design (SED

Criteria for seismic evaluation and potential design fixes for WWER type nuclear power plants

International Nuclear Information System (INIS)

Stevenson, J.D.

1995-01-01

The purpose for this document is to provide a criteria for the seismic evaluation and development of potential design fixes for structures, systems and components for the WWER type Nuclear power plants. The design fixes are divided into two categories, detailed and easy fixes. Detailed fixes are typically applicable to building structures, components for which there is little or no seismic capacity information, large tanks and vital systems and components which make up the reactor cooling system and components which perform support or auxiliary functions. In case of the design of 'easy fixes', the criteria presented may be used for both the seismic design as well as for the evaluation of structures, systems and components to which easy fix design applies. Easy fixes are situations where seismic capacities of structures, systems and components can be significantly increased with relatively minor, inexpensive fixes usually associated with anchorage modification of safety related structures, systems and components or those that could interact with safety related structures, systems and components. Often these fixes can be accomplished while the plant is in operation

Criteria for seismic evaluation and potential design fixes for WWER type nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Stevenson, J D [Stevenson and Associates, Cleveland, OH (United States)

1995-07-01

The purpose for this document is to provide a criteria for the seismic evaluation and development of potential design fixes for structures, systems and components for the WWER type Nuclear power plants. The design fixes are divided into two categories, detailed and easy fixes. Detailed fixes are typically applicable to building structures, componentsfor which there is little or no seismic capacity information, large tanks and vital systems and components which make up the reactor cooling system and components which perform support or auxiliary functions. In case of the design of 'easy fixes', the criteria presented may be used for both the seismic design as well as for the evaluation of structures, systems and components to which easy fix design applies. Easy fixes are situations where seismic capacities of structures, systems and components can be significantly increased with relatively minor, inexpensive fixes usually associated with anchorage modification of safety related structures, systems and components or those that could interact with safety related structures, systems and components. Often these fixes can be accomplished while the plant is in operation.

Design requirements, criteria and methods for seismic qualification of CANDU power plants

International Nuclear Information System (INIS)

Singh, N.; Duff, C.G.

1979-10-01

This report describes the requirements and criteria for the seismic design and qualification of systems and equipment in CANDU nuclear power plants. Acceptable methods and techniques for seismic qualification of CANDU nuclear power plants to mitigate the effects or the consequences of earthquakes are also described. (auth)

LMFBR safety criteria and guidelines for consideration in the design of future plants

International Nuclear Information System (INIS)

1990-01-01

For many years the Commission of the European Communities has been conducting activities aimed at the progressive harmonization of safety requirements and criteria applied to nuclear installations in the Community. These activities cover thermal and fast reactors. This publication represents a major achievement in reaching this goal. The document, which has been prepared in the framework of activities of the CEC fast-reactor safety working group (SWG), consists of safety criteria and guidelines for fast reactors. It represents the common view of all EC Member States which have a fast-reactor programme or are interested in fast-reactor development. The criteria and guidelines are structured according to different types of possible faults, such as core reactivity faults, general cooling faults, subassembly faults, faults outside the core and causes external to the station. Only those events are considered which are in the design basis of current fast-reactor projects. Proposed measures or guidelines to satisfy the criteria are based on the present knowledge and proven technology

A MULTI CRITERIA APPROACH TO DESIGNING THE CELLULAR MANUFACTURING SYSTEM

Directory of Open Access Journals (Sweden)

Rika Ampuh Hadiguna

2005-01-01

Full Text Available Cellular manufacturing system design problems such as design framework, manufacturing cells layout and layout evaluation. The research objective is developing the framework to designing manufacturing cells with considering the organization and management aspects in shopfloor. In this research have compared the existing layout with proposed layout which applied the multi criteria approach. The proposed method is combining Analytical Hierarchy Process (AHP, Clustering and heuristic approach. The result has show that grouping with Single Linkage Clustering (SLC to be selected as manufacturing cells. The comparison of clustering weight is 0,567, 0,245 and 0,188 for SLC, Complete Linkage Clustering (CLC and Average Linkage Clustering (ALC, respectively. This result shows that generating layout by using grouping result from SLC. The evaluation result shows that types of manufacturing cells better than process layout which used the existing system.

Reliability based code calibration of fatigue design criteria of nuclear Class-1 piping

International Nuclear Information System (INIS)

Mishra, J.; Balasubramaniyan, V.; Chellapandi, P.

2016-01-01

Fatigue design of Class-l piping of NPP is carried out using Section-III of American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel code. The fatigue design criteria of ASME are based on the concept of safety factor, which does not provide means for the management of uncertainties for consistently reliable and economical designs. In this regards, a work is taken up to estimate the implicit reliability level associated with fatigue design criteria of Class-l piping specified by ASME Section III, NB-3650. As ASME fatigue curve is not in the form of analytical expression, the reliability level of pipeline fittings and joints is evaluated using the mean fatigue curve developed by Argonne National Laboratory (ANL). The methodology employed for reliability evaluation is FORM, HORSM and MCS. The limit state function for fatigue damage is found to be sensitive to eight parameters, which are systematically modelled as stochastic variables during reliability estimation. In conclusion a number of important aspects related to reliability of various piping product and joints are discussed. A computational example illustrates the developed procedure for a typical pipeline. (author)

77 FR 38857 - Design, Inspection, and Testing Criteria for Air Filtration and Adsorption Units of Normal...

Science.gov (United States)

2012-06-29

... Filtration and Adsorption Units of Normal Atmosphere Cleanup Systems in Light-Water- Cooled Nuclear Power... Criteria for Air Filtration and Adsorption Units of Normal Atmosphere Cleanup Systems in Light-Water-Cooled... draft regulatory guide (DG), DG-1280, ``Design, Inspection, and Testing Criteria for Air Filtration and...

Rethinking exergy efficiency in favor of exergy sustainability as a criteria for design. Paper no. IGEC-1-ID12

International Nuclear Information System (INIS)

Seager, T.P.

2005-01-01

'Full text:' Engineering design in power generation or conversion has typically focused on minimizing exergy losses (entropy gains), or maximizing economic returns. Both entropy minimization and profit maximization are readily obtainable and acceptable objective criteria for design of thermodynamic processes. However, alternative criteria are imaginable. This research presents a framework for considering minimal environmental impact or maximum renewability as alternative design criteria. In the environmental case, fuel source is based upon an exergetic environmental metric called pollution potential. In the case of renewability, a life-cycle metric describing the replacement time frame of the fuel source is employed. When coupled, the two metrics together partially assess the overall sustainability of the design. (author)

22 CFR 96.6 - Performance criteria for designation as an accrediting entity.

Science.gov (United States)

2010-04-01

... other similar functions; (f) Except in the case of a public entity, that it operates independently of... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Performance criteria for designation as an accrediting entity. 96.6 Section 96.6 Foreign Relations DEPARTMENT OF STATE LEGAL AND RELATED SERVICES...

An intelligent, knowledge-based multiple criteria decision making advisor for systems design

Science.gov (United States)

Li, Yongchang

In systems engineering, design and operation of systems are two main problems which always attract researcher's attentions. The accomplishment of activities in these problems often requires proper decisions to be made so that the desired goal can be achieved, thus, decision making needs to be carefully fulfilled in the design and operation of systems. Design is a decision making process which permeates through out the design process, and is at the core of all design activities. In modern aircraft design, more and more attention is paid to the conceptual and preliminary design phases so as to increase the odds of choosing a design that will ultimately be successful at the completion of the design process, therefore, decisions made during these early design stages play a critical role in determining the success of a design. Since aerospace systems are complex systems with interacting disciplines and technologies, the Decision Makers (DMs) dealing with such design problems are involved in balancing the multiple, potentially conflicting attributes/criteria, transforming a large amount of customer supplied guidelines into a solidly defined set of requirement definitions. Thus, one could state with confidence that modern aerospace system design is a Multiple Criteria Decision Making (MCDM) process. A variety of existing decision making methods are available to deal with this type of decision problems. The selection of the most appropriate decision making method is of particular importance since inappropriate decision methods are likely causes of misleading engineering design decisions. With no sufficient knowledge about each of the methods, it is usually difficult for the DMs to find an appropriate analytical model capable of solving their problems. In addition, with the complexity of the decision problem and the demand for more capable methods increasing, new decision making methods are emerging with time. These various methods exacerbate the difficulty of the selection

Development of a design basis tornado and structural design criteria for the Nevada Test Site, Nevada. Final report

International Nuclear Information System (INIS)

McDonald, J.R.; Minor, J.E.; Mehta, K.C.

1975-06-01

In order to evaluate the ability of critical facilities at the Nevada Test Site to withstand the possible damaging effects of extreme winds and tornadoes, parameters for the effects of tornadoes and extreme winds and structural design criteria for the design and evaluation of structures were developed. The meteorological investigations conducted are summarized, and techniques used for developing the combined tornado and extreme wind risk model are discussed. The guidelines for structural design include methods for calculating pressure distributions on walls and roofs of structures and methods for accommodating impact loads from wind-driven missiles. Calculations for determining the design loads for an example structure are included

Evaluation of a School Building in Turkey According to the Basic Sustainable Design Criteria

Science.gov (United States)

Arslan, H. D.

2017-08-01

In Turkey, as well as many other developing countries, the significance of sustainable education buildings has only recently become recognized and the issue of sustainability issue has not been sufficiently involved in laws and regulations. In this study, first of all architectural sustainability with basic design criteria has been explained. After that selected type primary school project in Turkey has been evaluated according to the sustainable design criteria. Type project of school buildings significantly limits the sustainability performance expected from buildings. It is clear that type projects shorten the planning time as they include a designing process that is independent of settlement and they are repeated in various places with different characteristics, indeed. On the other hand; abundance of disadvantages such as the overlook of the natural physical and structural properties of the location mostly restricts the sustainable design of the building. For sustainable buildings, several factors such as the environment, land, climate, insolation, direction etc. shall be taken into consideration at the beginning stage. Therefore; implementation of type projects can be deemed to be inappropriate for sustainability.

Canister storage building compliance assessment DOE Order 6430.1A, General Design Criteria

International Nuclear Information System (INIS)

BLACK, D.M.

1999-01-01

This document presents the Project's position on compliance with DOE Order 6430.1A ''General Design Criteria.'' No non-compliances are shown. The compliance statements have been reviewed and approved by DOE. Open items are scheduled to be closed prior to project completion

Solving the Problem of Multiple-Criteria Building Design Decisions with respect to the Fire Safety of Occupants: An Approach Based on Probabilistic Modelling

Directory of Open Access Journals (Sweden)

Egidijus Rytas Vaidogas

2015-01-01

Full Text Available The design of buildings may include a comparison of alternative architectural and structural solutions. They can be developed at different levels of design process. The alternative design solutions are compared and ranked by applying methods of multiple-criteria decision-making (MCDM. Each design is characterised by a number of criteria used in a MCDM problem. The paper discusses how to choose MCDM criteria expressing fire safety related to alternative designs. Probability of a successful evacuation of occupants from a building fire and difference between evacuation time and time to untenable conditions are suggested as the most important criteria related to fire safety. These two criteria are treated as uncertain quantities expressed by probability distributions. Monte Carlo simulation of fire and evacuation processes is natural means for an estimation of these distributions. The presence of uncertain criteria requires applying stochastic MCDM methods for ranking alternative designs. An application of the safety-related criteria is illustrated by an example which analyses three alternative architectural floor plans prepared for a reconstruction of a medical building. A MCDM method based on stochastic simulation is used to solve the example problem.

Development of a design basis tornado and structural design criteria for Lawrence Livermore Laboratory's Site 300

International Nuclear Information System (INIS)

McDonald, J.R.; Minor, J.E.; Mehta, K.C.

1975-11-01

Criteria are prescribed and guidance is provided for professional personnel who are involved with the evaluation of existing buildings and facilities at Site 300 near Livermore, California to resist the possible effects of extreme winds and tornadoes. The development of parameters for the effects of tornadoes and extreme winds and guidelines for evaluation and design of structures are presented. The investigations conducted are summarized and the techniques used for arriving at the combined tornado and extreme wind risk model are discussed. The guidelines for structural design methods for calculating pressure distributions on walls and roofs of structures and methods for accommodating impact loads from missiles are also presented

Probabilistic risk criteria and their application to nuclear chemical plant design

International Nuclear Information System (INIS)

Arthur, T.; Barnes, D.S.; Brown, M.L.; Taig, A.R.; Johnston, B.D.; Hayns, M.

1989-01-01

A nuclear chemical plant safety strategy is presented. The use of risk criteria in design is demonstrated by reference to a particular area of the plant. This involves the application of Probabilistic Risk Assessment (PRA) techniques. Computer programs developed by the UK Atomic Energy Authority (UKAEA) at its Safety and Reliability Directorate (SRD) are used toe valuate and analyze the resultant fault trees. the magnitude of releases are estimated and individual and societal risks determined. The paper concludes that the application of PRA to a nuclear chemical plant can be structured in such a way as to allow a designer to work to quantitative risk targets

Technical regulations on the general design and safety criteria for design and construction of nuclear reactors of May 1975

International Nuclear Information System (INIS)

1975-05-01

These Technical Regulations published on 5th September 1975 were made in implementation of Section 33 of Decree No 7/9141 on the procedure for the licensing of nuclear installations. They serve as a guide to licensing authorities, project designers and operators in the nuclear field and therefore provide general criteria for safety standards, engineering codes, siting considerations, design bases for overall environmental radiation protection, and also deal with reactor core design, instrumentation, control, alarm systems, including an emergency core cooling system. Finally, the safe design of fuel elements must be ensured and fuel storage and handling techniques complied with. (NEA) [fr

Criteria for the design of the control room complex for a nuclear power generating station

International Nuclear Information System (INIS)

Anon.

1981-01-01

This Standard addresses the central control room of a nuclear power generating station and the overall complex in which this room is housed. It is not intended to cover special or normally unattended control rooms, such as those provided for radioactive waste handling or for emergency shutdown operations. The nuclear power generating station control room complex provides a protective envelope for plant operating personnel and for instrument and control equipment vital to the operation of the plant during normal and abnormal conditions. In this capacity, the control room complex must be designed and constructed to meet the following criteria contained in Appendix A of 10CFR50, General Design criteria for Nuclear Power Plants: (1) Criterion 2: design bases for protection against natural phenomena; (2) Criterion 3: fire protection; (3) Criterion 4: environmental and missile design bases; (4) Criterion 5: sharing of structures, systems and components (multiunit stations only); and (5) Criterion 19: control room

Ultra-realistic imaging advanced techniques in analogue and digital colour holography

CERN Document Server

Bjelkhagen, Hans

2013-01-01

Ultra-high resolution holograms are now finding commercial and industrial applications in such areas as holographic maps, 3D medical imaging, and consumer devices. Ultra-Realistic Imaging: Advanced Techniques in Analogue and Digital Colour Holography brings together a comprehensive discussion of key methods that enable holography to be used as a technique of ultra-realistic imaging.After a historical review of progress in holography, the book: Discusses CW recording lasers, pulsed holography lasers, and reviews optical designs for many of the principal laser types with emphasis on attaining th

Non realist tendencies in new Turkish cinema

OpenAIRE

Can, İclal

2016-01-01

http://hdl.handle.net/11693/29111 Thesis (M.S.): Bilkent University, Department of Communication and Design, İhsan Doğramacı Bilkent University, 2016. Includes bibliographical references (leaves 113-123). The realist tendency which had been dominant in cinema became more apparent with Italian neorealism affecting other national cinemas to a large extent. With the changing and developing socio economic and cultural dynamics, realism gradually has stopped being a natural const...

Realistic Visualization of Virtual Views

DEFF Research Database (Denmark)

Livatino, Salvatore

2005-01-01

that can be impractical and sometime impossible. In addition, the artificial nature of data often makes visualized virtual scenarios not realistic enough. Not realistic in the sense that a synthetic scene is easy to discriminate visually from a natural scene. A new field of research has consequently...... developed and received much attention in recent years: Realistic Virtual View Synthesis. The main goal is a high fidelity representation of virtual scenarios while easing modeling and physical phenomena simulation. In particular, realism is achieved by the transfer to the novel view of all the physical...... phenomena captured in the reference photographs, (i.e. the transfer of photographic-realism). An overview of most prominent approaches in realistic virtual view synthesis will be presented and briefly discussed. Applications of proposed methods to visual survey, virtual cinematography, as well as mobile...

Realistic minimum accident source terms - Evaluation, application, and risk acceptance

International Nuclear Information System (INIS)

Angelo, P. L.

2009-01-01

The evaluation, application, and risk acceptance for realistic minimum accident source terms can represent a complex and arduous undertaking. This effort poses a very high impact to design, construction cost, operations and maintenance, and integrated safety over the expected facility lifetime. At the 2005 Nuclear Criticality Safety Division (NCSD) Meeting in Knoxville Tenn., two papers were presented mat summarized the Y-12 effort that reduced the number of criticality accident alarm system (CAAS) detectors originally designed for the new Highly Enriched Uranium Materials Facility (HEUMF) from 258 to an eventual as-built number of 60. Part of that effort relied on determining a realistic minimum accident source term specific to the facility. Since that time, the rationale for an alternate minimum accident has been strengthened by an evaluation process that incorporates realism. A recent update to the HEUMF CAAS technical basis highlights the concepts presented here. (authors)

Functional design criteria for the retained gas sampler system

International Nuclear Information System (INIS)

Wootan, D.W.

1995-01-01

A Retained Gas Sampler System (RGSS) is being developed to capture and analyze waste samples from Hanford Flammable Gas Watch List Tanks to determine both the quantity and composition of gases retained in the waste. The RGSS consists of three main components: the Sampler, Extractor, and Extruder. This report describes the functional criteria for the design of the RGSS components. The RGSS Sampler is based on the WHC Universal Sampler design with modifications to eliminate gas leakage. The primary function of the Sampler is to capture a representative waste sample from a tank and transport the sample with minimal loss of gas content from the tank to the laboratory. The function of the Extruder is to transfer the waste sample from the Sampler to the Extractor. The function of the Extractor is to separate the gases from the liquids and solids, measure the relative volume of gas to determine the void fraction, and remove and analyze the gas constituents

Materials for Hydrogen Storage in Nanocavities: Design criteria

Energy Technology Data Exchange (ETDEWEB)

Reguera, E. [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada del IPN, Unidad Legaria, Legaria 694, Col. Irrigacion (Mexico)

2009-11-15

The adsorption potential for a given adsorbate depends of both, material surface and adsorbate properties. In this contribution the possible guest-host interactions for H{sub 2} within a cavity or on a surface are discussed considering the molecule physical properties. Five different interactions contribute to the adsorption forces for this molecule: 1) quadrupole moment interaction with the local electric field gradient; 1) electron cloud polarization by a charge center; 3) dispersive forces (van der Waals); 4) quadrupole moment versus quadrupole moment between neighboring H{sub 2} molecules, and, 5) H{sub 2} coordination to a metal center. The relative importance of these five interactions for the hydrogen storage in nanocavities is discussed from experimental evidences in order to extract materials design criteria for molecular hydrogen storage. (author)

Realistic nurse-led policy implementation, optimization and evaluation: novel methodological exemplar.

Science.gov (United States)

Noyes, Jane; Lewis, Mary; Bennett, Virginia; Widdas, David; Brombley, Karen

2014-01-01

To report the first large-scale realistic nurse-led implementation, optimization and evaluation of a complex children's continuing-care policy. Health policies are increasingly complex, involve multiple Government departments and frequently fail to translate into better patient outcomes. Realist methods have not yet been adapted for policy implementation. Research methodology - Evaluation using theory-based realist methods for policy implementation. An expert group developed the policy and supporting tools. Implementation and evaluation design integrated diffusion of innovation theory with multiple case study and adapted realist principles. Practitioners in 12 English sites worked with Consultant Nurse implementers to manipulate the programme theory and logic of new decision-support tools and care pathway to optimize local implementation. Methods included key-stakeholder interviews, developing practical diffusion of innovation processes using key-opinion leaders and active facilitation strategies and a mini-community of practice. New and existing processes and outcomes were compared for 137 children during 2007-2008. Realist principles were successfully adapted to a shorter policy implementation and evaluation time frame. Important new implementation success factors included facilitated implementation that enabled 'real-time' manipulation of programme logic and local context to best-fit evolving theories of what worked; using local experiential opinion to change supporting tools to more realistically align with local context and what worked; and having sufficient existing local infrastructure to support implementation. Ten mechanisms explained implementation success and differences in outcomes between new and existing processes. Realistic policy implementation methods have advantages over top-down approaches, especially where clinical expertise is low and unlikely to diffuse innovations 'naturally' without facilitated implementation and local optimization. © 2013

An approach to criteria, design limits and monitoring in nuclear fuel waste disposal

Energy Technology Data Exchange (ETDEWEB)

Simmons, G R; Baumgartner, P; Bird, G A; Davison, C C; Johnson, L H; Tamm, J A

1994-12-01

The Nuclear Fuel Waste Management Program has been established to develop and demonstrate the technology for safe geological disposal of nuclear fuel waste. One objective of the program is to show that a disposal system (i.e., a disposal centre and associated transportation system) can be designed and that it would be safe. Therefore the disposal system must be shown to comply with safety requirements specified in guidelines, standards, codes and regulations. The components of the disposal system must also be shown to operate within the limits specified in their design. Compliance and performance of the disposal system would be assessed on a site-specific basis by comparing estimates of the anticipated performance of the system and its components with compliance or performance criteria. A monitoring program would be developed to consider the effects of the disposal system on the environment and would include three types of monitoring: baseline monitoring, compliance monitoring, and performance monitoring. This report presents an approach to establishing compliance and performance criteria, limits for use in disposal system component design, and the main elements of a monitoring program for a nuclear fuel waste disposal system. (author). 70 refs., 9 tabs., 13 figs.

An approach to criteria, design limits and monitoring in nuclear fuel waste disposal

International Nuclear Information System (INIS)

Simmons, G.R.; Baumgartner, P.; Bird, G.A.; Davison, C.C.; Johnson, L.H.; Tamm, J.A.

1994-12-01

The Nuclear Fuel Waste Management Program has been established to develop and demonstrate the technology for safe geological disposal of nuclear fuel waste. One objective of the program is to show that a disposal system (i.e., a disposal centre and associated transportation system) can be designed and that it would be safe. Therefore the disposal system must be shown to comply with safety requirements specified in guidelines, standards, codes and regulations. The components of the disposal system must also be shown to operate within the limits specified in their design. Compliance and performance of the disposal system would be assessed on a site-specific basis by comparing estimates of the anticipated performance of the system and its components with compliance or performance criteria. A monitoring program would be developed to consider the effects of the disposal system on the environment and would include three types of monitoring: baseline monitoring, compliance monitoring, and performance monitoring. This report presents an approach to establishing compliance and performance criteria, limits for use in disposal system component design, and the main elements of a monitoring program for a nuclear fuel waste disposal system. (author). 70 refs., 9 tabs., 13 figs

17 CFR Appendix A to Part 38 - Guidance on Compliance With Designation Criteria

Science.gov (United States)

2010-04-01

... the criteria for designation. To the extent that compliance with, or satisfaction of, a criterion for... based on order priority factors other than price and time should include a brief explanation of the... financial integrity of transactions and intermediaries, and the protection of customer funds should include...

Blend Shape Interpolation and FACS for Realistic Avatar

Science.gov (United States)

Alkawaz, Mohammed Hazim; Mohamad, Dzulkifli; Basori, Ahmad Hoirul; Saba, Tanzila

2015-03-01

The quest of developing realistic facial animation is ever-growing. The emergence of sophisticated algorithms, new graphical user interfaces, laser scans and advanced 3D tools imparted further impetus towards the rapid advancement of complex virtual human facial model. Face-to-face communication being the most natural way of human interaction, the facial animation systems became more attractive in the information technology era for sundry applications. The production of computer-animated movies using synthetic actors are still challenging issues. Proposed facial expression carries the signature of happiness, sadness, angry or cheerful, etc. The mood of a particular person in the midst of a large group can immediately be identified via very subtle changes in facial expressions. Facial expressions being very complex as well as important nonverbal communication channel are tricky to synthesize realistically using computer graphics. Computer synthesis of practical facial expressions must deal with the geometric representation of the human face and the control of the facial animation. We developed a new approach by integrating blend shape interpolation (BSI) and facial action coding system (FACS) to create a realistic and expressive computer facial animation design. The BSI is used to generate the natural face while the FACS is employed to reflect the exact facial muscle movements for four basic natural emotional expressions such as angry, happy, sad and fear with high fidelity. The results in perceiving the realistic facial expression for virtual human emotions based on facial skin color and texture may contribute towards the development of virtual reality and game environment of computer aided graphics animation systems.

Toward User Interfaces and Data Visualization Criteria for Learning Design of Digital Textbooks

Science.gov (United States)

Railean, Elena

2014-01-01

User interface and data visualisation criteria are central issues in digital textbooks design. However, when applying mathematical modelling of learning process to the analysis of the possible solutions, it could be observed that results differ. Mathematical learning views cognition in on the base on statistics and probability theory, graph…

Design criteria of out-pile system of HANARO fuel test loop

Energy Technology Data Exchange (ETDEWEB)

Kim, J. Y.

1997-07-01

The objective of HANARO aims at the development and localization of nuclear technologies through the engineering tests. Thus it is very important the design and installation of the irradiation test facilities to be installed at the irradiation hole for verification test of the fuel performance are in connection with maximization of the utilization of HANARO. The principle subjects of this study are to presend and informed the detail design criteria and technical specification of out-pile system of HANARO fuel test loop for the developing of the fuel and reactor material. This results will become guidance for the planning of the irradiation testing using the HANARO fuel test loop. (author). 16 refs., 31 tabs., 9 figs.

Advancements in flow-induced vibration research and design criteria

International Nuclear Information System (INIS)

Pettigrew, M.J.

2009-01-01

Two-phase flow exists in many nuclear components and, in particular, steam generators. So far relatively little research work has been done on two-phase flow-induced vibration probably because it is difficult to do. Two-phase flows are not homogeneous and are governed by an additional parameter called void fraction. This can lead to different flow patterns or regimes that can change completely the vibration behaviour. Fluidelastic instability, random turbulence excitation and detailed flow characteristics are being investigated in tube bundles subjected to two-phase cross flow. Fluidelastic instability of a tube bundle preferentially flexible in the flow direction was observed probably for the first time. This is particularly relevant to the problem of in-plane vibration of nuclear steam generator U-tubes and has resulted in changes in our design criteria. Unexpected quasi-periodic excitation forces were also measured in the tube bundle. These are attributed to an alternating wake in the lift direction and to fluctuating momentum flux in the drag direction. Vibration damping due to two-phase flow is very dependent on void fraction and appears directly related to the interface surface area between phases. Maximum damping values correspond to the transitions between flow regimes. Fibre optic probes were developed to measure the characteristics of two-phase flows. These probes are used to take detailed measurements in a triangular array of tubes in cross flow. The results show that the flow tends to stream between the tubes. These studies have yielded interesting results but have raised more questions that could lead to improved design criteria. The more puzzling results will be discussed in this presentation. Some of the dynamic phenomena will be illustrated by animation. (author)

Developing Teaching Material Based on Realistic Mathematics Andoriented to the Mathematical Reasoning and Mathematical Communication

OpenAIRE

Habsah, Fitria

2017-01-01

This research aims to produce mathematics textbook for grade VII junior high school students based on realistic mathematics and oriented to the mathematical reasoning and mathematical communication. The quality is determined based on Nieveen criteria, including validity, practicality, and effectiveness.This study was a research and development and used Borg & Gall model. The subject of this research were the students of SMPN 2 Pujon-Kabupaten Malang, that is 30 students in an experimental cla...

The development of criteria for the design of insulation for nuclear reactors

International Nuclear Information System (INIS)

Furber, B.N.; Hopkins, I.H.G.; Stuart, R.A.

1976-01-01

In 1960 when the early design studies for the Oldbury Power Station were being carried out the use of insulation in a reactor environment was quite novel. No manufacturer had previous experience of this particular application of insulation. The paper describes the work carried out to establish the design criteria for Magnox and subsequent Advanced Gas Cooled Reactors (AGR) and indicates some of the new problems of the High Temperature Reactor (HTR). Unless otherwise stated the work was carried out by The Nuclear Power Group Ltd. (TNPG) and the conclusions express the present thinking of that Company. (author)

Intelligible design a realistic approach to the philosophy and history of science

CERN Document Server

Gonzalo, Julio A

2014-01-01

This book provides realistic answers to hotly debated scientific topics: Science is about quantitative aspects of natural realities (physical, chemical, biological) but it is the result of human intellectual inquiry and therefore not "per se" materialistic. This book, with contributions from experts in physics, cosmology, mathematics, engineering, biology and genetics, covers timely and relevant topics such as the origin of the universe, the origin of life on Earth, the origin of man (intelligent life) and the origin of science.

Triangulating and guarding realistic polygons

NARCIS (Netherlands)

Aloupis, G.; Bose, P.; Dujmovic, V.; Gray, C.M.; Langerman, S.; Speckmann, B.

2014-01-01

We propose a new model of realistic input: k-guardable objects. An object is k-guardable if its boundary can be seen by k guards. We show that k-guardable polygons generalize two previously identified classes of realistic input. Following this, we give two simple algorithms for triangulating

Small Business Conformity with Quality Website Design Criteria in a Marketing Communication Context

Directory of Open Access Journals (Sweden)

Martine Robinson Beachboard

2017-10-01

Full Text Available Aim/Purpose: Professional companies selling persuasive-communication services via the World Wide Web need to be exemplars of effective informing practices. Their credibility is at risk if their websites do not excel in marketing message and use of medium. Their unique brands need to be expressed through website technology and content, or they cannot compete successfully. Background: Compares marketing communication consultants’ websites with expert criteria. Methodology: Content analysis of 40 advertising agency websites. Contribution: Links an evaluation of advertising agency compliance with expert website criteria to established branding constructs. Findings: Most small advertising agencies could improve their brand reputations through better compliance with experts’ recommended website design and content criteria. Recommendations for Practitioners: A hierarchy of recommendations for practitioners is offered, addressing ease and importance. Impact on Society: Clarity and credibility of message and medium improve our ability to practice effective informing. Future Research: Explore online communications of specialized populations such as digital marketing experts.

Design and Management Criteria for Fish, Amphibian, and Reptile Communities Within Created Agricultural Wetlands

Science.gov (United States)

Design and management criteria for created agricultural wetlands in the midwestern United States typically focus on maximizing the ability to process agricultural runoff. Ecological benefits for fish, amphibian, and reptiles are often secondary considerations. One example of this water quality focu...

Affordable Design: A Methodolgy to Implement Process-Based Manufacturing Cost into the Traditional Performance-Focused Multidisciplinary Design Optimization

Science.gov (United States)

Bao, Han P.; Samareh, J. A.

2000-01-01

The primary objective of this paper is to demonstrate the use of process-based manufacturing and assembly cost models in a traditional performance-focused multidisciplinary design and optimization process. The use of automated cost-performance analysis is an enabling technology that could bring realistic processbased manufacturing and assembly cost into multidisciplinary design and optimization. In this paper, we present a new methodology for incorporating process costing into a standard multidisciplinary design optimization process. Material, manufacturing processes, and assembly processes costs then could be used as the objective function for the optimization method. A case study involving forty-six different configurations of a simple wing is presented, indicating that a design based on performance criteria alone may not necessarily be the most affordable as far as manufacturing and assembly cost is concerned.

Panel 1: Safety design criteria

International Nuclear Information System (INIS)

Yllera, Javier

2013-01-01

There is general consensus in the nuclear community, and more after the Fukushima accident, that the deployment of nuclear energy has to be done at the highest levels of nuclear safety and that safety cannot be compromised by other factors. It is well understood that reactors that are being licensed and the new generations of reactors that will be constructed in the future will need to reach higher safety levels than the existing ones. Several countries and international organizations or international groups are launching initiatives to harmonise safety goals, safety requirements, safety objectives, regulations, criteria or safety reference levels. There are differences in the meanings of these terms and the working approaches, but the overall purpose is the same: to specify how new plants can be safer. In this context, the IAEA has an statutory function for developing international nuclear safety standards. The IAEA safety standards are per se not mandatory for IAEA Member States. Regulating safety is a national responsibility, and many States have decided to adopt the IAEA’s standards for use in their national regulations in different ways. The IAEA Safety Standards represent international consensus on what must constitute a high level of safety for nuclear installations. In the area of NPP design, IAEA safety standards that are published are intended to apply primarily to new plants. It might not be practicable to apply all the requirements to plants that are already in operation. In addition, the focus is primarily on plants with water cooled reactors

Dynamic apeerture in damping rings with realistic wigglers

Energy Technology Data Exchange (ETDEWEB)

Cai, Yunhai; /SLAC

2005-05-04

The International Linear Collider based on superconducting RF cavities requires the damping rings to have extremely small equilibrium emittance, huge circumference, fast damping time, and large acceptance. To achieve all of these requirements is a very challenging task. In this paper, we will present a systematic approach to designing the damping rings using simple cells and non-interlaced sextupoles. The designs of the damping rings with various circumferences and shapes, including dogbone, are presented. To model realistic wigglers, we have developed a new hybrid symplectic integrator for faster and accurate evaluation of dynamic aperture of the lattices.

The computer-aided design of a servo system as a multiple-criteria decision problem

NARCIS (Netherlands)

Udink ten Cate, A.J.

1986-01-01

This paper treats the selection of controller gains of a servo system as a multiple-criteria decision problem. In contrast to the usual optimization-based approaches to computer-aided design, inequality constraints are included in the problem as unconstrained objectives. This considerably simplifies

Durability-Based Design Criteria for a Quasi-Isotropic Carbon-Fiber-Reinforced Thermoplastic Automotive Composite

Energy Technology Data Exchange (ETDEWEB)

Naus, Dan J [ORNL; Corum, James [ORNL; Klett, Lynn B [ORNL; Davenport, Mike [ORNL; Battiste, Rick [ORNL; Simpson, Jr., William A [ORNL

2006-04-01

This report provides recommended durability-based design properties and criteria for a quais-isotropic carbon-fiber thermoplastic composite for possible automotive structural applications. The composite consisted of a PolyPhenylene Sulfide (PPS) thermoplastic matrix (Fortron's PPS - Ticona 0214B1 powder) reinforced with 16 plies of carbon-fiber unidirectional tape, [0?/90?/+45?/-45?]2S. The carbon fiber was Hexcel AS-4C and was present in a fiber volume of 53% (60%, by weight). The overall goal of the project, which is sponsored by the U.S. Department of Energy's Office of Freedom Car and Vehicle Technologies and is closely coordinated with the Advanced Composites Consortium, is to develop durability-driven design data and criteria to assure the long-term integrity of carbon-fiber-based composite systems for automotive structural applications. This document is in two parts. Part 1 provides design data and correlations, while Part 2 provides the underlying experimental data and models. The durability issues addressed include the effects of short-time, cyclic, and sustained loadings; temperature; fluid environments; and low-energy impacts (e.g., tool drops and kickups of roadway debris) on deformation, strength, and stiffness. Guidance for design analysis, time-independent and time-dependent allowable stresses, rules for cyclic loadings, and damage-tolerance design guidance are provided.

The Effect of Realistic Mathematics Education Approach on Students' Achievement And Attitudes Towards Mathematics

OpenAIRE

Effandi Zakaria; Muzakkir Syamaun

2017-01-01

This study was conducted to determine the effect of Realistic Mathematics Education Approach on mathematics achievement and student attitudes towards mathematics. This study also sought determine the relationship between student achievement and attitudes towards mathematics. This study used a quasi-experimental design conducted on 61 high school students at SMA Unggul Sigli. Students were divided into two groups, the treatment group $(n = 30)$ namely, the Realistic Mathematics Approach group ...

ERG review of containment failure probability and repository functional design criteria

International Nuclear Information System (INIS)

Gopal, S.

1986-06-01

The Engineering Review Group (ERG) was established by the Office of Nuclear Waste Isolation (ONWI) to help evaluate engineering-related issues in the US Department of Energy's nuclear waste repository program. The June 1984 meeting of the ERG considered two topics: (1) statistical probability for containment of nuclides within the waste package and (2) repository design criteria. This report documents the ERG's comments and recommendations on these two subjects and the ONWI response to the specific points raised by ERG

Criteria for controlled atmosphere chambers

International Nuclear Information System (INIS)

Robinson, J.N.

1980-03-01

The criteria for design, construction, and operation of controlled atmosphere chambers intended for service at ORNL are presented. Classification of chambers, materials for construction, design criteria, design, controlled atmosphere chamber systems, and operating procedures are presented. ORNL Safety Manual Procedure 2.1; ORNL Health Physics Procedure Manual Appendix A-7; and Design of Viewing Windows are included in 3 appendices

Realistic roofs over a rectilinear polygon

KAUST Repository

Ahn, Heekap

2013-11-01

Given a simple rectilinear polygon P in the xy-plane, a roof over P is a terrain over P whose faces are supported by planes through edges of P that make a dihedral angle π/4 with the xy-plane. According to this definition, some roofs may have faces isolated from the boundary of P or even local minima, which are undesirable for several practical reasons. In this paper, we introduce realistic roofs by imposing a few additional constraints. We investigate the geometric and combinatorial properties of realistic roofs and show that the straight skeleton induces a realistic roof with maximum height and volume. We also show that the maximum possible number of distinct realistic roofs over P is ((n-4)(n-4)/4 /2⌋) when P has n vertices. We present an algorithm that enumerates a combinatorial representation of each such roof in O(1) time per roof without repetition, after O(n4) preprocessing time. We also present an O(n5)-time algorithm for computing a realistic roof with minimum height or volume. © 2013 Elsevier B.V.

Comparison of Epicyclic Gearing Design Methods by Means of Quality Criteria Evaluation

Directory of Open Access Journals (Sweden)

I. V. Leonov

2015-01-01

Full Text Available The performance of modern economy depends on the usage of different machines. Execution of the many tasks a society entrusts to the machinery requires a huge amount of the mechanical energy imparted to the mechanical system due to different engines. Combining the motors and actuators in turn occurs through various transmissions.Among the numerous types of transmission the planetary gears occupy an important place. With a number of advantages and differences from other types of transmission of rotational motion, planetary gear can be used as a gear or a differential gear. The planetary gear firmly holds a leading position for its frequent use in transmissions of various technological and transport vehicles, as it has a convenient layout and high load capacity.Despite the fact that people have been using planetary gears over two thousand years, there is no simple method of their design, allowing both a minimizing design time and an optimization of their performance characteristics and technological qualities.The proposed design method is derived from the classical method of factors. It limits the number of options by isolating a promising region of a set of reduced criteria values of the overall dimensions, one of the main design criteria. A minimizing size criterion optimization is provided through rapprochement of gear sizes in two rows of gearings and proximity to the minimum possible number of teeth from the undercut condition, environment for numerous satellites, and gear assembly as well as through specifying the numbers of teeth of one of the rows to be equal to the arithmetic average of the teeth numbers of the other row.

Recommended revisions to nuclear regulatory commission seismic design criteria

International Nuclear Information System (INIS)

Coats, D.W.

1981-01-01

Task Action Plan (TAP) A-40 was developed by consolidating specific technical assistance studies initiated to identify and quantify the conservatism inherent in the seismic design sequence of current NRC criteria. Task 10 of TAP A-40 provided a technical review of the results of the other nine engineering and seismological tasks in TAP A-40 and recommended changes to the existing NRC criteria based on this review. We used the team approach to accomplish the objectives of Task 10 in an efficient manner and to provide the best technical product possible within the limited time available. The team consisted of a core group of Lawrence Livermore National Laboratory personnel and selected consultants. The recommendations summarized in this paper were not based solely on the results of the tasks in TAP A-40 but went far beyond that data base to encompass all available and appropriate literature. Some recommendations are based on the expertise of core members and consultants that stem from unpublished data, research, and experience. Copies of the pertinent sections of the Standard Review Plan (SRP) and Regulatory Guides as well as the reports developed under TAP A-40 were provided to the participants. These reports, other available engineering literature, and the experience of the consultants and core group provided technical basis for the recommendations. (orig./HP)

The Effect of Realistic Mathematics Education Approach on Students' Achievement And Attitudes Towards Mathematics

Directory of Open Access Journals (Sweden)

Effandi Zakaria

2017-02-01

Full Text Available This study was conducted to determine the effect of Realistic Mathematics Education Approach on mathematics achievement and student attitudes towards mathematics. This study also sought determine the relationship between student achievement and attitudes towards mathematics. This study used a quasi-experimental design conducted on 61 high school students at SMA Unggul Sigli. Students were divided into two groups, the treatment group $(n = 30$ namely, the Realistic Mathematics Approach group (PMR and the control group $(n = 31$ namely, the traditional group. This study was conducted for six weeks. The instruments used in this study were the achievement test and the attitudes towards mathematics questionnaires. Data were analyzed using SPSS. To determine the difference in mean achievement and attitudes between the two groups, data were analyzed using one-way ANOVA test. The result showed significant differences between the Realistic Mathematics Approach and the traditional approach in terms of achievement. The study showed no significant difference between the Realistic Mathematics Approach and the traditional approach in term of attitudes towards mathematics. It can be concluded that the use of realistic mathematics education approach enhanced students' mathematics achievement, but not attitudes towards mathematics. The Realistic Mathematics Education Approach encourage students to participate actively in the teaching and learning of mathematics. Thus, Realistic Mathematics Education Approach is an appropriate methods to improve the quality of teaching and learning process.

Repository operational criteria analysis

International Nuclear Information System (INIS)

Hageman, J.P.; Chowdhury, A.H.

1992-08-01

The objective of the ''Repository Operational Criteria (ROC) Feasibility Studies'' (or ROC task) was to conduct comprehensive and integrated analyses of repository design, construction, and operations criteria in 10 CFR Part 60 regulations, considering the interfaces and impacts of any potential changes to those regulations. The study addresses regulatory criteria related to the preclosure aspects of the geologic repository. The study task developed regulatory concepts or potential repository operational criteria (PROC) based on analysis of a repository's safety functions and other regulations for similar facilities. These regulatory concepts or PROC were used as a basis to assess the sufficiency and adequacy of the current criteria in 10 CFR Part 60. Where the regulatory concepts were same as current operational criteria, these criteria were referenced. The operations criteria referenced or the PROC developed are given in this report. Detailed analyses used to develop the regulatory concepts and any necessary PROC for those regulations that may require a minor change are also presented. The results of the ROC task showed a need for further analysis and possible major rule change related to the design bases of a geologic repository operations area, siting, and radiological emergency planning

Third Joint GIF–IAEA Workshop on Safety Design Criteria for Sodium-Cooled Fast Reactors, 26-27 February 2013, Vienna, Austria. Summary Report

International Nuclear Information System (INIS)

2013-01-01

The main objectives of the meeting were to: • Present and share information on the work carried out by GIF, the IAEA and the Member States on the definition of safety design criteria for SFR, including safety approach and requirements on general plant design; • Present the document prepared by the GIF-SFR Task Force on Safety Design Criteria; • Present and discuss safety design concepts of SFRs under development in Member States, with particular emphasis on design measures against Design Basis Accidents and Design Extended Conditions, as well as the associated safety evaluations and supporting R&D; • Draft a room document which should be the basis of the discussion for the Panel on Safety Design Criteria of the FR13 Conference in Paris. • Discuss the results and agree on the future actions of the 3rd Joint GIF-IAEA Workshop on Safety of Sodium-Cooled Fast Reactors

42 CFR Appendix F to Part 5 - Criteria for Designation of Areas Having Shortages of Pharmacy Professional(s)

Science.gov (United States)

2010-10-01

... of Pharmacy Professional(s) F Appendix F to Part 5 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF..., App. F Appendix F to Part 5—Criteria for Designation of Areas Having Shortages of Pharmacy... of pharmacy professional(s) if the following three criteria are met: 1. The area is a rational area...

42 CFR Appendix G to Part 5 - Criteria for Designation of Areas Having Shortages of Veterinary Professional(s)

Science.gov (United States)

2010-10-01

... of Veterinary Professional(s) G Appendix G to Part 5 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT... Pt. 5, App. G Appendix G to Part 5—Criteria for Designation of Areas Having Shortages of Veterinary Professional(s) Part I—Geographic Areas A. Criteria for Food Animal Veterinary Shortage. A geographic area will...

Recommended revisions to Nuclear Regulatory Commission seismic design criteria. Technical report

International Nuclear Information System (INIS)

Coats, D.W.

1980-05-01

This report recommends changes in the Nuclear Regulatory Commission's (NRC's) criteria now used in the seismic design of nuclear power plants. Areas covered include ground motion, soil-structure interaction, structures, and equipment and components. Members of the Engineering Mechanics Section of the Nuclear Test Engineering Division at Lawrence Livermore Laboratory (LLL) generally agreed upon the recommendations, which are based on (1) reports developed under the NRC's Task Action Plan A-40, (2) other available engineering literature, and (3) recommendations of nationally recognized experts retained by LLL specifically for this task

Functional design criteria radioactive liquid waste line replacement, Project W-087. Revision 3

International Nuclear Information System (INIS)

McVey, C.B.

1994-01-01

This document provides the functional design criteria for the 222-S Laboratory radioactive waste drain piping and transfer pipeline replacement. The project will replace the radioactive waste drain piping from the hot cells in 222-S to the 219-S Waste Handling Facility and provide a new waste transfer route from 219-S to the 244-S Catch Station in Tank Farms

The 1995 forum on appropriate criteria and methods for seismic design of nuclear piping

International Nuclear Information System (INIS)

Slagis, G.C.

1996-01-01

A record of the 1995 Forum on Appropriate Criteria and Methods for Seismic Design of Nuclear Piping is provided. The focus of the forum was the earthquake experience data base and whether the data base demonstrates that seismic inertia loads will not cause failure in ductile piping systems. This was a follow-up to the 1994 Forum when the use of earthquake experience data, including the recent Northridge earthquake, to justify a design-by-rule method was explored. Two possible topics for the next forum were identified--inspection after an earthquake and design for safe-shutdown earthquake only

Preliminary proposed seismic design and evaluation criteria for new and existing underground hazardous materials storage tanks

International Nuclear Information System (INIS)

Kennedy, R.P.

1991-01-01

The document provides a recommended set of deterministic seismic design and evaluation criteria for either new or existing underground hazardous materials storage tanks placed in either the high hazard or moderate hazard usage catagories of UCRL-15910. The criteria given herein are consistent with and follow the same philosophy as those given in UCRL-15910 for the US Department of Energy facilities. This document is intended to supplement and amplify upon Reference 1 for underground hazardous materials storage tanks

Architectural design criteria for f-block metal sequestering agents. 1997 annual progress report

International Nuclear Information System (INIS)

Hay, B.P.; Paine, R.T.; Roundhill, D.M.

1997-01-01

'The objective of this project is to provide the means to optimize ligand architecture for f-block metal recognition. The authors strategy builds on an innovative and successful molecular modeling approach in developing polyether ligand design criteria for the alkali and alkaline earth cations. The hypothesis underlying this proposal is that differences in metal ion binding with multidentate ligands bearing the same number and type of donor groups are primarily attributable to intramolecular steric factors. The authors propose quantifying these steric factors through the application of molecular mechanics models. The proposed research involves close integration of theoretical and experimental chemistry. The experimental work entails synthesizing novel ligands and experimentally determining structures and binding constants for metal ion complexation by series of ligands in which architecture is systematically varied. The theoretical work entails using electronic structure calculations to parameterize a molecular mechanics force field for a range of metal ions and ligand types. The resulting molecular mechanics force field will be used to predict low-energy structures for unidentate, bidentate, and multidentate ligands and their metal complexes through conformational searches. Results will be analyzed to assess the relative importance of several steric factors including optimal M-L length, optimal geometry at the metal center, optimal geometry at the donor atoms (complementarity), and conformation prior to binding (preorganization). An accurate set of criteria for the design of ligand architecture will be obtained from these results. These criteria will enable researchers to target ligand structures for synthesis and thereby dramatically reduce the time and cost associated with metal-specific ligand development.'

Probability-Based Design Criteria of the ASCE 7 Tsunami Loads and Effects Provisions (Invited)

Science.gov (United States)

Chock, G.

2013-12-01

Mitigation of tsunami risk requires a combination of emergency preparedness for evacuation in addition to providing structural resilience of critical facilities, infrastructure, and key resources necessary for immediate response and economic and social recovery. Critical facilities would include emergency response, medical, tsunami refuges and shelters, ports and harbors, lifelines, transportation, telecommunications, power, financial institutions, and major industrial/commercial facilities. The Tsunami Loads and Effects Subcommittee of the ASCE/SEI 7 Standards Committee is developing a proposed new Chapter 6 - Tsunami Loads and Effects for the 2016 edition of the ASCE 7 Standard. ASCE 7 provides the minimum design loads and requirements for structures subject to building codes such as the International Building Code utilized in the USA. In this paper we will provide a review emphasizing the intent of these new code provisions and explain the design methodology. The ASCE 7 provisions for Tsunami Loads and Effects enables a set of analysis and design methodologies that are consistent with performance-based engineering based on probabilistic criteria. . The ASCE 7 Tsunami Loads and Effects chapter will be initially applicable only to the states of Alaska, Washington, Oregon, California, and Hawaii. Ground shaking effects and subsidence from a preceding local offshore Maximum Considered Earthquake will also be considered prior to tsunami arrival for Alaska and states in the Pacific Northwest regions governed by nearby offshore subduction earthquakes. For national tsunami design provisions to achieve a consistent reliability standard of structural performance for community resilience, a new generation of tsunami inundation hazard maps for design is required. The lesson of recent tsunami is that historical records alone do not provide a sufficient measure of the potential heights of future tsunamis. Engineering design must consider the occurrence of events greater than

Radiation Damage to Nervous System: Designing Optimal Models for Realistic Neuron Morphology in Hippocampus

Science.gov (United States)

Batmunkh, Munkhbaatar; Bugay, Alexander; Bayarchimeg, Lkhagvaa; Lkhagva, Oidov

2018-02-01

The present study is focused on the development of optimal models of neuron morphology for Monte Carlo microdosimetry simulations of initial radiation-induced events of heavy charged particles in the specific types of cells of the hippocampus, which is the most radiation-sensitive structure of the central nervous system. The neuron geometry and particles track structures were simulated by the Geant4/Geant4-DNA Monte Carlo toolkits. The calculations were made for beams of protons and heavy ions with different energies and doses corresponding to real fluxes of galactic cosmic rays. A simple compartmental model and a complex model with realistic morphology extracted from experimental data were constructed and compared. We estimated the distribution of the energy deposition events and the production of reactive chemical species within the developed models of CA3/CA1 pyramidal neurons and DG granule cells of the rat hippocampus under exposure to different particles with the same dose. Similar distributions of the energy deposition events and concentration of some oxidative radical species were obtained in both the simplified and realistic neuron models.

Preliminary design concepts for the advanced neutron source reactor systems

International Nuclear Information System (INIS)

Peretz, F.J.

1988-01-01

This paper describes the initial design work to develop the reactor systems hardware concepts for the advanced neutron source (ANS) reactor. This project has not yet entered the conceptual design phase; thus, design efforts are quite preliminary. This paper presents the collective work of members of the Oak Ridge National Laboratory, Martin Marietta Energy Systems, Inc., Engineering Division, and other participating organizations. The primary purpose of this effort is to show that the ANS reactor concept is realistic from a hardware standpoint and to show that project objectives can be met. It also serves to generate physical models for use in neutronic and thermal-hydraulic core design efforts and defines the constraints and objectives for the design. Finally, this effort will develop the criteria for use in the conceptual design of the reactor

Design criteria and candidate electrical power systems for a reusable Space Shuttle booster.

Science.gov (United States)

Merrifield, D. V.

1972-01-01

This paper presents the results of a preliminary study to establish electrical power requirements, investigate candidate power sources, and select a representative power generation concept for the NASA Space Shuttle booster stage. Design guidelines and system performance requirements are established. Candidate power sources and combinations thereof are defined and weight estimates made. The selected power source concept utilizes secondary silver-zinc batteries, engine-driven alternators with constant speed drive, and an airbreathing gas turbine. The need for cost optimization, within safety, reliability, and performance constraints, is emphasized as being the most important criteria in design of the final system.

JSFR design progress related to development of safety design criteria for generation IV sodium-cooled fast reactors. (3) Progress of component design

International Nuclear Information System (INIS)

Enuma, Yasuhiro; Kawasaki, Nobuchika; Orita, Junichi; Eto, Masao; Miyagawa, Takayuki

2015-01-01

In the frame work of generation IV international forum (GIF), safety design criteria (SDC) and safety design guideline (SDG) for the generation IV sodium-cooled fast reactors have been developing in the circumstance of worldwide deployment of SFRs. JAEA, JAPC, MFBR have been investigating design study for JSFR to satisfy SDC in the feasibility study of SDG for Sodium-cooled Fast Reactor (SFR). In addition to the safety measures, maintainability, reparability and manufacturability are taken into account in the JSFR design study. This paper describes the design of main components. Enlargement of the access route for the inspection devices and addition of the access routes were carried out for the reactor structure. The pump-integrated IHX (pump/IHX) was modified for the primary heat exchanger (PHX), which was installed for the decay heat removal in the IHX at the upper plenum, to be removable for improved repair and maintenance. For the steam generator (SG), protective wall tube type design is under investigation as an option with less R and D risks. (author)

Two non-tracking solar collectors: Design criteria and performance analysis

International Nuclear Information System (INIS)

Ratismith, Wattana; Inthongkhum, Anusorn; Briggs, John

2014-01-01

Highlights: • A collector module designed to capture solar radiation efficiently is proposed. • Two different compound parabolic trough designs are examined and tested. • A novel design with a flat base trough and vertical absorber operates efficiently in direct and diffuse sunlight. - Abstract: We propose fixed (non-tracking) configurations of solar light collector modules which are designed to operate efficiently throughout the day, i.e. for varying incident angles of direct sunlight, and in conditions of diffuse solar irradiation. We present two trough designs of compound parabolic collector (CPC) type. One, a more conventional double-parabolic trough, has the absorber plate perpendicular to the vertical axis of the trough cross-section. The other, of a new flat-base shape, has the absorber plate parallel. The collectors have two novel features appropriate to non-tracking. The first is a smoothing of the power output over the day by the simple expedient of arranging three troughs tilted at different angles. The second is the original design of the flat-base trough allowing optimal interception of the caustic surfaces of this non-focussing device. By ray-tracing analysis of the different trough shapes and absorber plate orientation, we emphasise the design criteria for achievement of a high intercept factor throughout the day without tracking and demonstrate the superiority of the flat-base collector over the double-parabolic design. In test experiments we show that the high temperatures (≈180 °C) necessary for some industrial process heat applications can be achieved. Also test results of the efficiency of the proposed systems are presented which indicate that the flat-base trough with vertical absorber plate is superior to the double-parabolic trough with horizontal absorber plate

Realistically Rendering SoC Traffic Patterns with Interrupt Awareness

DEFF Research Database (Denmark)

Angiolini, Frederico; Mahadevan, Sharkar; Madsen, Jan

2005-01-01

to generate realistic test traffic. This paper presents a selection of applications using interrupt-based synchronization; a reference methodology to split such applications in execution subflows and to adjust the overall execution stream based upon hardware events; a reactive simulation device capable...... of correctly replicating such software behaviours in the MPSoC design phase. Additionally, we validate the proposed concept by showing cycle-accurate reproduction of a previously traced application flow....

Fail-safe design criteria for computer-based reactor protection systems

International Nuclear Information System (INIS)

Keats, A.B.

1980-01-01

The increasing quantity and complexity of the instrumentation required in nuclear power plants provides a strong incentive for using on-line computers as the basis of the control and protection systems. On-line computers using multiplexed sampled data are already well established but their application to nuclear reactor protection systems requires special measures to satisfy the very high reliability which is demanded in the interests of safety and availability. Some existing codes of practice relating to segregation of replicated subsysttems continue to be applicable and lead to division of the computer functions into two distinct parts. The first computer, referred to as the Trip Algorithm Computer may also control the multiplexer. Voting on each group of status inputs yielded by the trip algorithm computers is performed by the Vote Algorithm Computer. The conceptual disparities between hardwired reactor-protection systems and those employing computers also rise to a need for some new criteria. An important objective of these criteria, minimising the need for a failure-mode-and-effect-analysis of the computer software, but is achieved almost entirely by 'hardware' properties of the system: the systematic use of hardwired test inputs which cause excursions of the trip algorithms into the tripped state in a uniquely ordered but easily recognisable sequence, and the use of hardwired 'pattern recognition logic' which generates a dynamic 'healthy' stimulus for the shutdown actuators only in response to the unique sequence generated by the hardwired input signal pattern. The adoption of the proposed design criteria ensure not only failure-to-safety in the hardware but the elimination, or at least minimisation, of the dependence on the correct functioning of the computer software for the safety system. (auth)

Design criteria for stable Pt/C fuel cell catalysts

Directory of Open Access Journals (Sweden)

Josef C. Meier

2014-01-01

Full Text Available Platinum and Pt alloy nanoparticles supported on carbon are the state of the art electrocatalysts in proton exchange membrane fuel cells. To develop a better understanding on how material design can influence the degradation processes on the nanoscale, three specific Pt/C catalysts with different structural characteristics were investigated in depth: a conventional Pt/Vulcan catalyst with a particle size of 3–4 nm and two Pt@HGS catalysts with different particle size, 1–2 nm and 3–4 nm. Specifically, Pt@HGS corresponds to platinum nanoparticles incorporated and confined within the pore structure of the nanostructured carbon support, i.e., hollow graphitic spheres (HGS. All three materials are characterized by the same platinum loading, so that the differences in their performance can be correlated to the structural characteristics of each material. The comparison of the activity and stability behavior of the three catalysts, as obtained from thin film rotating disk electrode measurements and identical location electron microscopy, is also extended to commercial materials and used as a basis for a discussion of general fuel cell catalyst design principles. Namely, the effects of particle size, inter-particle distance, certain support characteristics and thermal treatment on the catalyst performance and in particular the catalyst stability are evaluated. Based on our results, a set of design criteria for more stable and active Pt/C and Pt-alloy/C materials is suggested.

Buckling design criteria for waste package disposal containers in mined salt repositories: Technical report

International Nuclear Information System (INIS)

Mallett, R.H.

1986-12-01

This report documents analytical and experimental results from a survey of the technical literature on buckling of thick-walled cylinders under external pressure. Based upon these results, a load factor is suggested for the design of waste package containers for disposal of high-level radioactive waste in repositories mined in salt formations. The load factor is defined as a ratio of buckling pressure to allowable pressure. Specifically, a load factor which ranges from 1.5 for plastic buckling to 3.0 for elastic buckling is included in a set of proposed buckling design criteria for waste disposal containers. Formulas are given for buckling design under axisymmetric conditions. Guidelines are given for detailed inelastic buckling analyses which are generally required for design of disposal containers

Multiple-Criteria Decision-Making in the Design of Innovative Lock Walls for Barge Impact; Phase 1

National Research Council Canada - National Science Library

Lambert, James

2001-01-01

.... This research project consists of two phases: Phase 1, which culminates with this report, investigated the use of multiple-criteria decision-making in the design process of lock approach walls to consider barge impact and earthquake loads...

Fundamental criteria for the design of high-performance Josephson nondestructive readout random access memory cells and experimental confirmation

International Nuclear Information System (INIS)

Henkels, W.H.

1979-01-01

Fundamental design criteria for Josephson nondestructive readout random access memory (NDRO RAM) cells are presented, within the context of an LSI array environment. Emphasis is placed upon principles which are relevant to high performance. The criteria are elucidated via a specific design which is simulated and then experimentally evaluated in a technology with a smallest critical dimension of 5 μm. The specific cell differs from previously tested Josephson NDRO cells in several respects; namely, the cell stores only approx.8Phi 0 , employs interferometer gates and an external damping resistor, allows switching into device resonances, and eliminates the need for a special initialization cycle. The cell-selection scheme, employing triple coincidence, results in larger operating margins and smaller operating currents than have previously been achieved. The large operating margins and all basic cell design criteria were experimentally verified. The experimental interferometer gate characteristics were analyzed in detail and found to be describable by simple models. In addition, it was discovered that single flux quantum transitions in the interferometer gates could be exploited beneficially in order to enhance the insensitivity of operating margins to fabrication tolerances

Explaining the Criteria of Designing Urban Furniture and Landscape, with a Cultural-social Design Approach

Directory of Open Access Journals (Sweden)

Marzieh Allahdadi

2017-09-01

Full Text Available Attention to the deep relationship between human personality and the place in which he lives causes the place to play a crucial role in cultural transformations and prevalence of human life style and formation of values, connections and human activities. Cities are not just a place of transit, but they are also environments that must have mutual communications with the inhabitants in order to realize the meaning of citizen, as there is a distinction between the status of citizenship and urbanization. Urban furniture is one of the elements of urban space that its quantity, beauty and durability play a major role in achieving a healthy and favorable city and satisfies the needs of citizens in terms of performance and beauty. Accordingly, the present study, using descriptive-analytical method and with data collection tools including library and documentary studies, examines the concept of product ecology and answers to the questions whether urban furniture can start or support social interaction or positively affect the roles of citizens? In this paper, the relationship between social-cultural design in urban furniture and the disturbances regarding uneven distribution of elements are identified, and finally the criteria of designing urban furniture and landscape are expressed with a social-design approach.

Tuukka Kaidesoja on Critical Realist Transcendental Realism

Directory of Open Access Journals (Sweden)

Groff Ruth

2015-09-01

Full Text Available I argue that critical realists think pretty much what Tukka Kaidesoja says that he himself thinks, but also that Kaidesoja’s objections to the views that he attributes to critical realists are not persuasive.

Architectural design criteria for f-block metal ion sequestering agents. 1998 annual progress report

International Nuclear Information System (INIS)

Dixon, D.A.; Hay, B.P.; Paine, R.T.; Raymond, K.N.; Rogers, R.D.; Roundhill, D.M.

1998-01-01

'The objective of this project is to provide a means to optimize ligand architecture for f-block metal recognition. The authors strategy builds on an innovative and successful molecular modeling approach in developing polyether ligand design criteria for the alkali and alkaline earth cations. The hypothesis underlying this proposal is that differences in metal ion binding with multidentate ligands bearing the same number and type of donor groups are primarily attributable to intramolecular steric factors. They propose quantifying these steric factors through the application of molecular mechanics models. The research involves close integration of theoretical and experimental chemistry. The experimental work entails synthesizing novel ligands and experimentally determining structures and binding constants for metal ion complexation by series of ligands in which architecture is systematically varied. The theoretical work entails using electronic structure calculations to parameterize a molecular mechanics force field for a range of metal ions and ligand types. The resulting molecular mechanics force field will be used to predict low energy structures for unidentate, bidentate, and multidentate ligands and their metal complexes through conformational searches. Results will be analyzed to assess the relative importance of several steric factors including optimal M-L length, optimal geometry at the metal center, optimal geometry at the donor atoms (complementarity), and conformation prior to binding (preorganization). An accurate set of criteria for the design of ligand architecture will be obtained from these results. These criteria will enable researchers to target ligand structures for synthesis and thereby dramatically reduce the time and cost associated with metal-specific ligand development.'

A multi-criteria decision aid methodology to design electric vehicles public charging networks

Directory of Open Access Journals (Sweden)

João Raposo

2015-05-01

Full Text Available This article presents a new multi-criteria decision aid methodology, dynamic-PROMETHEE, here used to design electric vehicle charging networks. In applying this methodology to a Portuguese city, results suggest that it is effective in designing electric vehicle charging networks, generating time and policy based scenarios, considering offer and demand and the city’s urban structure. Dynamic-PROMETHE adds to the already known PROMETHEE’s characteristics other useful features, such as decision memory over time, versatility and adaptability. The case study, used here to present the dynamic-PROMETHEE, served as inspiration and base to create this new methodology. It can be used to model different problems and scenarios that may present similar requirement characteristics.

A multi-criteria decision aid methodology to design electric vehicles public charging networks

Science.gov (United States)

Raposo, João; Rodrigues, Ana; Silva, Carlos; Dentinho, Tomaz

2015-05-01

This article presents a new multi-criteria decision aid methodology, dynamic-PROMETHEE, here used to design electric vehicle charging networks. In applying this methodology to a Portuguese city, results suggest that it is effective in designing electric vehicle charging networks, generating time and policy based scenarios, considering offer and demand and the city's urban structure. Dynamic-PROMETHE adds to the already known PROMETHEE's characteristics other useful features, such as decision memory over time, versatility and adaptability. The case study, used here to present the dynamic-PROMETHEE, served as inspiration and base to create this new methodology. It can be used to model different problems and scenarios that may present similar requirement characteristics.

Nuclear Fuel Safety Criteria Technical Review - Second edition

International Nuclear Information System (INIS)

Beck, Winfried; Blanpain, Patrick; Fuketa, Toyoshi; Gorzel, Andreas; Hozer, Zoltan; Kamimura, Katsuichiro; Koo, Yang-Hyun; Maertens, Dietmar; Nechaeva, Olga; Petit, Marc; Rehacek, Radomir; Rey-Gayo, Jose Maria; Sairanen, Risto; Sonnenburg, Heinz-Guenther; Valach, Mojmir; Waeckel, Nicolas; Yueh, Ken; Zhang, Jinzhao; Voglewede, John

2012-01-01

Most of the current nuclear fuel safety criteria were established during the 1960's and early 1970's. Although these criteria were validated against experiments with fuel designs available at that time, a number of tests were based on unirradiated fuels. Additional verification was performed as these designs evolved, but mostly with the aim of showing that the new designs adequately complied with existing criteria, and not to establish new limits. In 1996, the OECD Nuclear Energy Agency (NEA) reviewed existing fuel safety criteria, focusing on new fuel and core designs, new cladding materials and industry manufacturing processes. The results were published in the Nuclear Fuel Safety Criteria Technical Review of 2001. The NEA has since re-examined the criteria. A brief description of each criterion and its rationale are presented in this second edition, which will be of interest to both regulators and industry (fuel vendors, utilities)

Validation of proposed diagnostic criteria (the "Budapest Criteria") for Complex Regional Pain Syndrome.

Science.gov (United States)

Harden, R Norman; Bruehl, Stephen; Perez, Roberto S G M; Birklein, Frank; Marinus, Johan; Maihofner, Christian; Lubenow, Timothy; Buvanendran, Asokumar; Mackey, Sean; Graciosa, Joseph; Mogilevski, Mila; Ramsden, Christopher; Chont, Melissa; Vatine, Jean-Jacques

2010-08-01

Current IASP diagnostic criteria for CRPS have low specificity, potentially leading to overdiagnosis. This validation study compared current IASP diagnostic criteria for CRPS to proposed new diagnostic criteria (the "Budapest Criteria") regarding diagnostic accuracy. Structured evaluations of CRPS-related signs and symptoms were conducted in 113 CRPS-I and 47 non-CRPS neuropathic pain patients. Discriminating between diagnostic groups based on presence of signs or symptoms meeting IASP criteria showed high diagnostic sensitivity (1.00), but poor specificity (0.41), replicating prior work. In comparison, the Budapest clinical criteria retained the exceptional sensitivity of the IASP criteria (0.99), but greatly improved upon the specificity (0.68). As designed, the Budapest research criteria resulted in the highest specificity (0.79), again replicating prior work. Analyses indicated that inclusion of four distinct CRPS components in the Budapest Criteria contributed to enhanced specificity. Overall, results corroborate the validity of the Budapest Criteria and suggest they improve upon existing IASP diagnostic criteria for CRPS. Copyright (c) 2010 International Association for the Study of Pain. Published by Elsevier B.V. All rights reserved.

Rock Slope Design Criteria

Science.gov (United States)

2010-06-01

Based on the stratigraphy and the type of slope stability problems, the flat lying, Paleozoic age, sedimentary : rocks of Ohio were divided into three design units: 1) competent rock design unit consisting of sandstones, limestones, : and siltstones ...

Selection of bioaccumulation criteria for environmental emergency (E2) planning

International Nuclear Information System (INIS)

Ketcheson, K.; Hradecky, K.; Gagne, M.; St-Amant-Verret, M.

2006-01-01

Environment Canada's Environmental Emergency regulations require the evaluation of a substance by a Risk Evaluation Framework (REF). Bioaccumulation criteria are used within the environmental hazard ratings section of the REF to determine the risk of a substance to organisms and are obtained from 3 types of measurements depending on data reliability: (1) bioaccumulation factors (BAF); (2) bioconcentration factors (BCF); and (3) an octanol-water partition coefficient (log K ow ). This paper presented details of a study of international and regional bioaccumulation criteria conducted to aid in determining appropriate criteria for E2 regulations and plans, with specific reference to substances toxic to aquatic organisms. An E2 plan is required if a substance has a bioconcentration factor of more than 500 in conjunction with aquatic toxicity. Bioaccumulation criteria from several sources for 745 substances were obtained to aid in choosing the most important parameters. Various international and regional criteria were examined and corresponding sources were summarized, and different source criteria was compared with empirical chemical data. The criteria chosen included both log K ow values and BCF values, although it was suggested that BCF and BAF are more realistic measures of bioaccumulation than log K ow , as they are derived from animal studies. The chosen values agreed with the virtual elimination criteria set out by the Canadian Environmental Protection Act (CEPA) 1999 as well as United States Environmental Protection Agency (EPA) criteria. It was concluded that the bioaccumulation criteria for E2 planning will help Environment Canada ensure the protection of the environment from hazardous substances. 11 refs., 3 tabs., 5 figs

Generating realistic roofs over a rectilinear polygon

KAUST Repository

Ahn, Heekap

2011-01-01

Given a simple rectilinear polygon P in the xy-plane, a roof over P is a terrain over P whose faces are supported by planes through edges of P that make a dihedral angle π/4 with the xy-plane. In this paper, we introduce realistic roofs by imposing a few additional constraints. We investigate the geometric and combinatorial properties of realistic roofs, and show a connection with the straight skeleton of P. We show that the maximum possible number of distinct realistic roofs over P is ( ⌊(n-4)/4⌋ (n-4)/2) when P has n vertices. We present an algorithm that enumerates a combinatorial representation of each such roof in O(1) time per roof without repetition, after O(n 4) preprocessing time. We also present an O(n 5)-time algorithm for computing a realistic roof with minimum height or volume. © 2011 Springer-Verlag.

Evaluation Criteria for the Educational Web-Information System

Science.gov (United States)

Seok, Soonhwa; Meyen, Edward; Poggio, John C.; Semon, Sarah; Tillberg-Webb, Heather

2008-01-01

This article addresses how evaluation criteria improve educational Web-information system design, and the tangible and intangible benefits of using evaluation criteria, when implemented in an educational Web-information system design. The evaluation criteria were developed by the authors through a content validation study applicable to…

Design criteria for the 200-ZP-1 interim remedial measure

International Nuclear Information System (INIS)

Mudge, J.F.; Olson, J.W.

1995-08-01

The Interim Remedial Measure Proposed Plan for the 200-ZP-1 Operable Unit recommended a pump and treat action to contain contaminated groundwater and limit further degradation of groundwater due to elevated concentrations of carbon tetrachloride, chloroform, and trichloroethylene in the 200-ZP-1 Operable Unit. This design criteria document defines the Project. The Project encompasses: site preparation; development of groundwater wells for monitoring, extraction, and injection; extraction and injection equipment; construction of a treatment system with support buildings/utilities; management; engineering design, analysis, and reporting; and operation and maintenance. A groundwater pump and treat system, hereafter the System, will be composed of extraction wells, a piping network, treatment equipment, water storage, and injection wells. Based upon engineering judgment, the selected technology in the proposed plan (DOE-RL 1994a) is air stripping of the organic contaminants followed by vapor-phase adsorption onto granulated activated carbon (GAC); liquid-phase GAC may be required as a polishing step. The Treatment Equipment refers to air stripping towers, adsorption vessels, water pumps, air blowers, instrumentation, and control devices which will be procured as a turn-key system

Development of a realistic human airway model.

Science.gov (United States)

Lizal, Frantisek; Elcner, Jakub; Hopke, Philip K; Jedelsky, Jan; Jicha, Miroslav

2012-03-01

Numerous models of human lungs with various levels of idealization have been reported in the literature; consequently, results acquired using these models are difficult to compare to in vivo measurements. We have developed a set of model components based on realistic geometries, which permits the analysis of the effects of subsequent model simplification. A realistic digital upper airway geometry except for the lack of an oral cavity has been created which proved suitable both for computational fluid dynamics (CFD) simulations and for the fabrication of physical models. Subsequently, an oral cavity was added to the tracheobronchial geometry. The airway geometry including the oral cavity was adjusted to enable fabrication of a semi-realistic model. Five physical models were created based on these three digital geometries. Two optically transparent models, one with and one without the oral cavity, were constructed for flow velocity measurements, two realistic segmented models, one with and one without the oral cavity, were constructed for particle deposition measurements, and a semi-realistic model with glass cylindrical airways was developed for optical measurements of flow velocity and in situ particle size measurements. One-dimensional phase doppler anemometry measurements were made and compared to the CFD calculations for this model and good agreement was obtained.

JSFR design progress related to development of safety design criteria for generation IV sodium-cooled fast reactors. (4) Balance of plant

International Nuclear Information System (INIS)

Chikazawa, Yoshitaka; Katoh, Atsushi; Nabeshima, Kunihiko; Ohtaka, Masahiko; Uzawa, Masayuki; Ikari, Risako; Iwasaki, Mikinori

2015-01-01

In this paper, design study and evaluation related with safety design criteria (SDC) and safety design guideline (SDG) on the balance of plant (BOP) of the demonstration JSFR including fuel handling system, power supply system, component cooling water system, building arrangement are reported. For the fuel handling system, enhancement of storage cooling system has been investigated adding diversified cooling systems. For the power supply, existing emergency power supply system has been reinforced and alternative emergency power supply system is added. For the component cooling system, requirements and relation with safety grade components such investigated. Additionally for the component cooling system, design impact when adding decay heat removal system by sea water has been investigated. For reactor building, over view of evaluation on the external events and design policy for distributed arrangement is reported. Those design study and evaluation provides background information of SDC and SDG. (author)

Risk-based determination of design pressure of LNG fuel storage tanks based on dynamic process simulation combined with Monte Carlo method

International Nuclear Information System (INIS)

Noh, Yeelyong; Chang, Kwangpil; Seo, Yutaek; Chang, Daejun

2014-01-01

This study proposes a new methodology that combines dynamic process simulation (DPS) and Monte Carlo simulation (MCS) to determine the design pressure of fuel storage tanks on LNG-fueled ships. Because the pressure of such tanks varies with time, DPS is employed to predict the pressure profile. Though equipment failure and subsequent repair affect transient pressure development, it is difficult to implement these features directly in the process simulation due to the randomness of the failure. To predict the pressure behavior realistically, MCS is combined with DPS. In MCS, discrete events are generated to create a lifetime scenario for a system. The combination of MCS with long-term DPS reveals the frequency of the exceedance pressure. The exceedance curve of the pressure provides risk-based information for determining the design pressure based on risk acceptance criteria, which may vary with different points of view. - Highlights: • The realistic operation scenario of the LNG FGS system is estimated by MCS. • In repeated MCS trials, the availability of the FGS system is evaluated. • The realistic pressure profile is obtained by the proposed methodology. • The exceedance curve provides risk-based information for determining design pressure

Development of realistic thermal hydraulic system analysis code

Energy Technology Data Exchange (ETDEWEB)

Lee, Won Jae; Chung, B. D; Kim, K. D. [and others

2002-05-01

The realistic safety analysis system is essential for nuclear safety research, advanced reactor development, safety analysis in nuclear industry and 'in-house' plant design capability development. In this project, we have developed a best-estimate multi-dimensional thermal-hydraulic system code, MARS, which is based on the integrated version of the RELAP5 and COBRA-TF codes. To improve the realistic analysis capability, we have improved the models for multi-dimensional two-phase flow phenomena and for advanced two-phase flow modeling. In addition, the GUI (Graphic User Interface) feature were developed to enhance the user's convenience. To develop the coupled analysis capability, the MARS code were linked with the three-dimensional reactor kinetics code (MASTER), the core thermal analysis code (COBRA-III/CP), and the best-estimate containment analysis code (CONTEMPT), resulting in MARS/MASTER/COBRA/CONTEMPT. Currently, the MARS code system has been distributed to 18 domestic organizations, including research, industrial, regulatory organizations and universities. The MARS has been being widely used for the safety research of existing PWRs, advanced PWR, CANDU and research reactor, the pre-test analysis of TH experiments, and others.

Development of realistic thermal hydraulic system analysis code

International Nuclear Information System (INIS)

Lee, Won Jae; Chung, B. D; Kim, K. D.

2002-05-01

The realistic safety analysis system is essential for nuclear safety research, advanced reactor development, safety analysis in nuclear industry and 'in-house' plant design capability development. In this project, we have developed a best-estimate multi-dimensional thermal-hydraulic system code, MARS, which is based on the integrated version of the RELAP5 and COBRA-TF codes. To improve the realistic analysis capability, we have improved the models for multi-dimensional two-phase flow phenomena and for advanced two-phase flow modeling. In addition, the GUI (Graphic User Interface) feature were developed to enhance the user's convenience. To develop the coupled analysis capability, the MARS code were linked with the three-dimensional reactor kinetics code (MASTER), the core thermal analysis code (COBRA-III/CP), and the best-estimate containment analysis code (CONTEMPT), resulting in MARS/MASTER/COBRA/CONTEMPT. Currently, the MARS code system has been distributed to 18 domestic organizations, including research, industrial, regulatory organizations and universities. The MARS has been being widely used for the safety research of existing PWRs, advanced PWR, CANDU and research reactor, the pre-test analysis of TH experiments, and others

Kuhn: Realist or Antirealist?

Directory of Open Access Journals (Sweden)

Michel Ghins

1998-06-01

Full Text Available Although Kuhn is much more an antirealist than a realist, the earlier and later articulations of realist and antirealist ingredients in his views merit close scrutiny. What are the constituents of the real invariant World posited by Kuhn and its relation to the mutable paradigm-related worlds? Various proposed solutions to this problem (dubbed the "new-world problem" by Ian Hacking are examined and shown to be unsatisfactory. In The Structure of Scientific Revolutions, the stable World can reasonably be taken to be made up of ordinary perceived objects, whereas in Kuhn's later works the transparadigmatic World is identified with something akin to the Kantian world-in-itself. It is argued that both proposals are beset with insuperable difficulties which render Kuhn's earlier and later versions of antirealism implausible.

Margin improvement initiatives: realistic approaches

Energy Technology Data Exchange (ETDEWEB)

Chan, P.K.; Paquette, S. [Royal Military College of Canada, Chemistry and Chemical Engineering Dept., Kingston, ON (Canada); Cunning, T.A. [Department of National Defence, Ottawa, ON (Canada); French, C.; Bonin, H.W. [Royal Military College of Canada, Chemistry and Chemical Engineering Dept., Kingston, ON (Canada); Pandey, M. [Univ. of Waterloo, Waterloo, ON (Canada); Murchie, M. [Cameco Fuel Manufacturing, Port Hope, ON (Canada)

2014-07-01

With reactor core aging, safety margins are particularly tight. Two realistic and practical approaches are proposed here to recover margins. The first project is related to the use of a small amount of neutron absorbers in CANDU Natural Uranium (NU) fuel bundles. Preliminary results indicate that the fuelling transient and subsequent reactivity peak can be lowered to improve the reactor's operating margins, with minimal impact on burnup when less than 1000 mg of absorbers is added to a fuel bundle. The second project involves the statistical analysis of fuel manufacturing data to demonstrate safety margins. Probability distributions are fitted to actual fuel manufacturing datasets provided by Cameco Fuel Manufacturing, Inc. They are used to generate input for ELESTRES and ELOCA. It is found that the fuel response distributions are far below industrial failure limits, implying that margin exists in the current fuel design. (author)

40 CFR 64.3 - Monitoring design criteria.

Science.gov (United States)

2010-07-01

... duct). (iv) Established as interdependent between more than one indicator. (b) Performance criteria... collection procedures that will be used (e.g., computerized data acquisition and handling, alarm sensor, or..., noninstrumental measurement of waste feed rate or visible emissions, use of a portable analyzer or an alarm sensor...

Precocious realists: perceptual and cognitive characteristics associated with drawing talent in non-autistic children

Science.gov (United States)

Drake, Jennifer E.; Winner, Ellen

2009-01-01

A local processing bias in the block design task and in drawing strategy has been used to account for realistic drawing skill in individuals with autism. We investigated whether the same kind of local processing bias is seen in typically developing children with unusual skill in realistic graphic representation. Forty-three 5–11-year-olds who drew a still life completed a version of the block design task in both standard and segmented form, were tested for their memory for the block design items, and were given the Kaufmann Brief Intelligence Test-II. Children were classified as gifted, moderately gifted or typical on the basis of the level of realism in their drawings. Similar to autistic individuals, the gifted group showed a local processing bias in the block design task. But unlike autistic individuals, the gifted group showed a global advantage in the visual memory task and did not use a local drawing strategy; in addition, their graphic realism skill was related to verbal IQ. Differences in the extent of local processing bias in autistic and typically developing children with drawing talent are discussed. PMID:19528030

Design criteria for XeF2 enabled deterministic transformation of bulk silicon (100) into flexible silicon layer

KAUST Repository

Hussain, Aftab M.

2016-07-15

Isotropic etching of bulk silicon (100) using Xenon Difluoride (XeF2) gas presents a unique opportunity to undercut and release ultra-thin flexible silicon layers with pre-fabricated state-of-the-art Complementary Metal Oxide Semiconductor (CMOS) electronics. In this work, we present design criteria and mechanism with a comprehensive mathematical model for this method. We consider various trench geometries and parametrize important metrics such as etch time, number of cycles and area efficiency in terms of the trench diameter and spacing so that optimization can be done for specific applications. From our theoretical analysis, we conclude that a honeycomb-inspired hexagonal distribution of trenches can produce the most efficient release of ultra-thin flexible silicon layers in terms of the number of etch cycles, while a rectangular distribution of circular trenches provides the most area efficient design. The theoretical results are verified by fabricating and releasing (varying sizes) flexible silicon layers. We observe uniform translation of design criteria into practice for etch distances and number of etch cycles, using reaction efficiency as a fitting parameter.

Design criteria for XeF2 enabled deterministic transformation of bulk silicon (100) into flexible silicon layer

KAUST Repository

Hussain, Aftab M.; Shaikh, Sohail F.; Hussain, Muhammad Mustafa

2016-01-01

Isotropic etching of bulk silicon (100) using Xenon Difluoride (XeF2) gas presents a unique opportunity to undercut and release ultra-thin flexible silicon layers with pre-fabricated state-of-the-art Complementary Metal Oxide Semiconductor (CMOS) electronics. In this work, we present design criteria and mechanism with a comprehensive mathematical model for this method. We consider various trench geometries and parametrize important metrics such as etch time, number of cycles and area efficiency in terms of the trench diameter and spacing so that optimization can be done for specific applications. From our theoretical analysis, we conclude that a honeycomb-inspired hexagonal distribution of trenches can produce the most efficient release of ultra-thin flexible silicon layers in terms of the number of etch cycles, while a rectangular distribution of circular trenches provides the most area efficient design. The theoretical results are verified by fabricating and releasing (varying sizes) flexible silicon layers. We observe uniform translation of design criteria into practice for etch distances and number of etch cycles, using reaction efficiency as a fitting parameter.

Green Supplier Selection Criteria

DEFF Research Database (Denmark)

Nielsen, Izabela Ewa; Banaeian, Narges; Golinska, Paulina

2014-01-01

Green supplier selection (GSS) criteria arise from an organization inclination to respond to any existing trends in environmental issues related to business management and processes, so GSS is integrating environmental thinking into conventional supplier selection. This research is designed...... to determine prevalent general and environmental supplier selection criteria and develop a framework which can help decision makers to determine and prioritize suitable green supplier selection criteria (general and environmental). In this research we considered several parameters (evaluation objectives......) to establish suitable criteria for GSS such as their production type, requirements, policy and objectives instead of applying common criteria. At first a comprehensive and deep review on prevalent and green supplier selection literatures performed. Then several evaluation objectives defined to assess the green...

Proposed design criteria for a fusion facility electrical ground system

International Nuclear Information System (INIS)

Armellino, C.A.

1983-01-01

Ground grid design considerations for a nuclear fusion reactor facility are no different than any other facility in that the basis for design must be safety first and foremost. Unlike a conventional industrial facility the available fault energy comes not only from the utility source and in-house rotating machinery, but also from energy storage capacitor banks, collapsing magnetic fields and D.C. transmission lines. It is not inconceivable for a fault condition occurrence where all available energy can be discharged. The ground grid must adequately shunt this sudden energy discharge in a way that personnel will not be exposed by step and/or touch to hazardous energy levels that are in excess of maximum tolerable levels for humans. Fault energy discharge rate is a function of the ground grid surge impedance characteristic. Closed loop paths must be avoided in the ground grid design so that during energy discharge no stray magnetic fields or large voltage potentials between remote points can be created by circulating currents. Single point connection of equipment to the ground grid will afford protection to personnel and sensitive equipment by reducing the probability of circulating currents. The overall ground grid system design is best illustrated as a wagon wheel concept with the fusion machine at the center. Radial branches or spokes reach out to the perimeter limits designated by step-and-touch high risk areas based on soil resistivity criteria considerations. Conventional methods for the design of a ground grid with all of its radial branches are still pertinent. The center of the grid could include a deep well single ground rod element the length of which is at least equivalent to the radius of an imaginary sphere that enshrouds the immediate machine area. Special facilities such as screen rooms or other shielded areas are part of the ground grid system by way of connection to radial branches

A multi-criteria approach to camera motion design for volume data animation.

Science.gov (United States)

Hsu, Wei-Hsien; Zhang, Yubo; Ma, Kwan-Liu

2013-12-01

We present an integrated camera motion design and path generation system for building volume data animations. Creating animations is an essential task in presenting complex scientific visualizations. Existing visualization systems use an established animation function based on keyframes selected by the user. This approach is limited in providing the optimal in-between views of the data. Alternatively, computer graphics and virtual reality camera motion planning is frequently focused on collision free movement in a virtual walkthrough. For semi-transparent, fuzzy, or blobby volume data the collision free objective becomes insufficient. Here, we provide a set of essential criteria focused on computing camera paths to establish effective animations of volume data. Our dynamic multi-criteria solver coupled with a force-directed routing algorithm enables rapid generation of camera paths. Once users review the resulting animation and evaluate the camera motion, they are able to determine how each criterion impacts path generation. In this paper, we demonstrate how incorporating this animation approach with an interactive volume visualization system reduces the effort in creating context-aware and coherent animations. This frees the user to focus on visualization tasks with the objective of gaining additional insight from the volume data.

Camelot 3: Habitability criteria space research and design studio

Science.gov (United States)

Arroyo, F.; Budet, O.; Garcia, A.; Lee, J.; Lopez, R.; Lugo, R.; Mateo, A.; Mellado, R.; Mendez, H.; Ortiz, N.

1989-01-01

Acknowledging the importance of human beings on a mission to Mars, the University of Puerto Rico studied both psychological and physiological aspects. Different conditions necessary for human health and well-being were considered. As a result, habitability criteria were developed. The criteria are as follows: personal identification; social interaction; unpredictable conditions; contact with nature; mental landscapes; privacy; equalitarian conditions; variety; functionality; sensory stimulation; music and environmental sound; stability and security; comfort; and sense of orientation.

Criteria for selection of target materials and design of high-efficiency-release targets for radioactive ion beam generation

CERN Document Server

Alton, G D; Liu, Y

1999-01-01

In this report, we define criteria for choosing target materials and for designing, mechanically stable, short-diffusion-length, highly permeable targets for generation of high-intensity radioactive ion beams (RIBs) for use at nuclear physics and astrophysics research facilities based on the ISOL principle. In addition, lists of refractory target materials are provided and examples are given of a number of successful targets, based on these criteria, that have been fabricated and tested for use at the Holifield Radioactive Ion Beam Facility (HRIBF).

Evaluation of health promotion in schools: a realistic evaluation approach using mixed methods

Science.gov (United States)

2010-01-01

Background Schools are key settings for health promotion (HP) but the development of suitable approaches for evaluating HP in schools is still a major topic of discussion. This article presents a research protocol of a program developed to evaluate HP. After reviewing HP evaluation issues, the various possible approaches are analyzed and the importance of a realistic evaluation framework and a mixed methods (MM) design are demonstrated. Methods/Design The design is based on a systemic approach to evaluation, taking into account the mechanisms, context and outcomes, as defined in realistic evaluation, adjusted to our own French context using an MM approach. The characteristics of the design are illustrated through the evaluation of a nationwide HP program in French primary schools designed to enhance children's social, emotional and physical health by improving teachers' HP practices and promoting a healthy school environment. An embedded MM design is used in which a qualitative data set plays a supportive, secondary role in a study based primarily on a different quantitative data set. The way the qualitative and quantitative approaches are combined through the entire evaluation framework is detailed. Discussion This study is a contribution towards the development of suitable approaches for evaluating HP programs in schools. The systemic approach of the evaluation carried out in this research is appropriate since it takes account of the limitations of traditional evaluation approaches and considers suggestions made by the HP research community. PMID:20109202

State-of-the-Art Prescriptive Criteria Weight Elicitation

Directory of Open Access Journals (Sweden)

Mona Riabacke

2012-01-01

Full Text Available Comparatively few of the vast amounts of decision analytical methods suggested have been widely spread in actual practice. Some approaches have nevertheless been more successful in this respect than others. Quantitative decision making has moved from the study of decision theory founded on a single criterion towards decision support for more realistic decision-making situations with multiple, often conflicting, criteria. Furthermore, the identified gap between normative and descriptive theories seems to suggest a shift to more prescriptive approaches. However, when decision analysis applications are used to aid prescriptive decision-making processes, additional demands are put on these applications to adapt to the users and the context. In particular, the issue of weight elicitation is crucial. There are several techniques for deriving criteria weights from preference statements. This is a cognitively demanding task, subject to different biases, and the elicited values can be heavily dependent on the method of assessment. There have been a number of methods suggested for assessing criteria weights, but these methods have properties which impact their applicability in practice. This paper provides a survey of state-of-the-art weight elicitation methods in a prescriptive setting.

Regulatory principles, criteria and guidelines for site selection, design, construction and operation of uranium tailings retention systems

International Nuclear Information System (INIS)

Coady, J.R.; Henry, L.C.

1978-01-01

Principles, criteria and guidelines developed by the Atomic Energy Control Board for the management of uranium mill tailings are discussed. The application of these concepts is considered in relation to site selection, design and construction, operation and decommissioning of tailings retention facilities

Functional design criteria for FY 1993-2000 groundwater monitoring wells

International Nuclear Information System (INIS)

Williams, B.A.

1996-01-01

The purpose of this revision is to update the Line Item Project, 93-L-GFW-152 Functional Design Criteria (FDC) to reflect changes approved in change control M-24-91-6, Engineering Change Notices (ECNs), and expand the scope to include subsurface investigations along with the borehole drilling. This revision improves the ability and effectiveness of maintaining RCRA and Operational groundwater compliance by combining borehole and well drilling with subsurface data gathering objectives. The total projected number of wells to be installed under this project has decreased from 200 and the scope has been broadened to include additional subsurface investigation activities that usually occur simultaneously with most traditional borehole drilling and monitoring well installations. This includes borehole hydrogeologic characterization activities, and vadose monitoring. These activities are required under RCRA 40 CFR 264 and 265 and WAC 173-303 for site characterization, groundwater and vadose assessment and well placement

Top-level regulatory criteria for the standard MHTGR

Energy Technology Data Exchange (ETDEWEB)

NONE

1986-10-15

The Licensing Plan for the Standard MHTGR (Ref. 1) describes a program to support a U.S. Nuclear Regulatory Commission (NRC) design review and approval. The Plan calls for the submittal of Top-Level Regulatory Criteria to the NRC for concurrence with their completeness and acceptability for the MHTGR program. The Top-Level Regulatory Criteria are defined as the standards for judging licensability that directly specify acceptable limits for protection of the public health and safety and the environment. The criteria proposed herein are for normal plant operation and a broad spectrum of anticipated events, including accidents. The approach taken is to define a set of criteria which are general as opposed to being design specific. Specifically, it is recommended that criteria be met which: 1. Are less prescriptive than current regulation, thereby encouraging maximum flexibility in design approaches. 2. Are measurable. 3. Are not more strict than the criteria for current power plants.

Assessing Outcomes of a Realistic Major Preview in an Introductory Sport Management Course

Science.gov (United States)

Pierce, David; Wanless, Elizabeth; Johnson, James

2014-01-01

This paper assessed the outcomes of a field experience assignment (FEA) in an introductory sport management course designed as a realistic major preview. Student learning outcomes assessed were commitment to the major, intent to pursue the major, expectation of a career in sports, and perceived preparation for a career in sports. A…

Barrier potential design criteria in multiple-quantum-well-based solar-cell structures

Science.gov (United States)

Mohaidat, Jihad M.; Shum, Kai; Wang, W. B.; Alfano, R. R.

1994-01-01

The barrier potential design criteria in multiple-quantum-well (MQW)-based solar-cell structures is reported for the purpose of achieving maximum efficiency. The time-dependent short-circuit current density at the collector side of various MQW solar-cell structures under resonant condition was numerically calculated using the time-dependent Schroedinger equation. The energy efficiency of solar cells based on the InAs/Ga(y)In(1-y)As and GaAs/Al(x)Ga(1-x)As MQW structues were compared when carriers are excited at a particular solar-energy band. Using InAs/Ga(y)In(1-y)As MQW structures it is found that a maximum energy efficiency can be achieved if the structure is designed with barrier potential of about 450 meV. The efficiency is found to decline linearly as the barrier potential increases for GaAs/Al(x)Ga(1-x)As MQW-structure-based solar cells.

Evaluating impact of clinical guidelines using a realist evaluation framework.

Science.gov (United States)

Reddy, Sandeep; Wakerman, John; Westhorp, Gill; Herring, Sally

2015-12-01

The Remote Primary Health Care Manuals (RPHCM) project team manages the development and publication of clinical protocols and procedures for primary care clinicians practicing in remote Australia. The Central Australian Rural Practitioners Association Standard Treatment Manual, the flagship manual of the RPHCM suite, has been evaluated for accessibility and acceptability in remote clinics three times in its 20-year history. These evaluations did not consider a theory-based framework or a programme theory, resulting in some limitations with the evaluation findings. With the RPHCM having an aim of enabling evidence-based practice in remote clinics and anecdotally reported to do so, testing this empirically for the full suite is vital for both stakeholders and future editions of the RPHCM. The project team utilized a realist evaluation framework to assess how, why and for what the RPHCM were being used by remote practitioners. A theory regarding the circumstances in which the manuals have and have not enabled evidence-based practice in the remote clinical context was tested. The project assessed this theory for all the manuals in the RPHCM suite, across government and aboriginal community-controlled clinics, in three regions of Australia. Implementing a realist evaluation framework to generate robust findings in this context has required innovation in the evaluation design and adaptation by researchers. This article captures the RPHCM team's experience in designing this evaluation. © 2015 John Wiley & Sons, Ltd.

Adapting realist synthesis methodology: The case of workplace harassment interventions.

Science.gov (United States)

Carr, Tracey; Quinlan, Elizabeth; Robertson, Susan; Gerrard, Angie

2017-12-01

Realist synthesis techniques can be used to assess complex interventions by extracting and synthesizing configurations of contexts, mechanisms, and outcomes found in the literature. Our novel and multi-pronged approach to the realist synthesis of workplace harassment interventions describes our pursuit of theory to link macro and program level theories. After discovering the limitations of a dogmatic approach to realist synthesis, we adapted our search strategy and focused our analysis on a subset of data. We tailored our realist synthesis to understand how, why, and under what circumstances workplace harassment interventions are effective. The result was a conceptual framework to test our theory-based interventions and provide the basis for subsequent realist evaluation. Our experience documented in this article contributes to an understanding of how, under what circumstances, and with what consequences realist synthesis principles can be customized. Copyright © 2017 John Wiley & Sons, Ltd.

NSSS supplier's response to differing safety criteria

Energy Technology Data Exchange (ETDEWEB)

Cremades, J; Filkin, R; Franke, T [Westinghouse Electric Nuclear Energy Systems Europe (WENESE), Brussels (Belgium)

1980-11-01

The limited progress achieved to date in harmonizing national criteria has led to the development of designs which include the most common national requirements. Progress towards harmonization of safety criteria can be accelerated by expanding the IAEA leadership and co-ordination activities, and implementing an integrated approach to criteria development. National and International safety criteria are examined.

Criteria for operator review of workplace changes

International Nuclear Information System (INIS)

Davey, E.

2000-01-01

A set of criteria for reviewing workplace changes has been developed for use by plant Operations staff. The criteria were developed to provide Operations staff with a practical framework for structuring assessments and subsequent review comments with regard to control room modifications and innovations that impact their work environment. The criteria were assembled from design, operations and human factors engineering principles, and system review experiences with plant Operations staff over the past ten years. Operations staff at several CANDU stations helped shape the emphasis for initial criteria definition and have assisted with criteria refinement through trial applications. Use of the criteria is expected to lead to more effective and task relevant equipment evaluations by Operations staff, and ultimately lead to system modifications and innovations that better serve plant operation needs. The paper begins with a discussion of the rationale for criteria development and the attributes of 'good' design. The balance of the paper outlines the project objectives, describes the approach applied in assembling, structuring, and refining the review criteria, and illustrates the application of the criteria in the review of a proposed control room innovation. (author)

Evaluation of photovoltaic panel temperature in realistic scenarios

International Nuclear Information System (INIS)

Du, Yanping; Fell, Christopher J.; Duck, Benjamin; Chen, Dong; Liffman, Kurt; Zhang, Yinan; Gu, Min; Zhu, Yonggang

2016-01-01

Highlights: • The developed realistic model captures more reasonably the thermal response and hysteresis effects. • The predicted panel temperature is as high as 60 °C under a solar irradiance of 1000 W/m"2 in no-wind weather. • In realistic scenarios, the thermal response normally takes 50–250 s. • The actual heating effect may cause a photoelectric efficiency drop of 2.9–9.0%. - Abstract: Photovoltaic (PV) panel temperature was evaluated by developing theoretical models that are feasible to be used in realistic scenarios. Effects of solar irradiance, wind speed and ambient temperature on the PV panel temperature were studied. The parametric study shows significant influence of solar irradiance and wind speed on the PV panel temperature. With an increase of ambient temperature, the temperature rise of solar cells is reduced. The characteristics of panel temperature in realistic scenarios were analyzed. In steady weather conditions, the thermal response time of a solar cell with a Si thickness of 100–500 μm is around 50–250 s. While in realistic scenarios, the panel temperature variation in a day is different from that in steady weather conditions due to the effect of thermal hysteresis. The heating effect on the photovoltaic efficiency was assessed based on real-time temperature measurement of solar cells in realistic weather conditions. For solar cells with a temperature coefficient in the range of −0.21%∼−0.50%, the current field tests indicated an approximate efficiency loss between 2.9% and 9.0%.

Spectroscopic criteria for identification of nuclear tetrahedral and octahedral symmetries: Illustration on a rare earth nucleus

Science.gov (United States)

Dudek, J.; Curien, D.; Dedes, I.; Mazurek, K.; Tagami, S.; Shimizu, Y. R.; Bhattacharjee, T.

2018-02-01

We formulate criteria for identification of the nuclear tetrahedral and octahedral symmetries and illustrate for the first time their possible realization in a rare earth nucleus 152Sm. We use realistic nuclear mean-field theory calculations with the phenomenological macroscopic-microscopic method, the Gogny-Hartree-Fock-Bogoliubov approach, and general point-group theory considerations to guide the experimental identification method as illustrated on published experimental data. Following group theory the examined symmetries imply the existence of exotic rotational bands on whose properties the spectroscopic identification criteria are based. These bands may contain simultaneously states of even and odd spins, of both parities and parity doublets at well-defined spins. In the exact-symmetry limit those bands involve no E 2 transitions. We show that coexistence of tetrahedral and octahedral deformations is essential when calculating the corresponding energy minima and surrounding barriers, and that it has a characteristic impact on the rotational bands. The symmetries in question imply the existence of long-lived shape isomers and, possibly, new waiting point nuclei—impacting the nucleosynthesis processes in astrophysics—and an existence of 16-fold degenerate particle-hole excitations. Specifically designed experiments which aim at strengthening the identification arguments are briefly discussed.

Inelastic analysis acceptance criteria for radioactive material transportation containers

International Nuclear Information System (INIS)

Ammerman, D.J.; Ludwigsen, J.S.

1993-01-01

The design criteria currently used in the design of radioactive material (RAM) transportation containers are taken from the ASME Boiler and Pressure Vessel Code (ASME, 1992). These load-based criteria are ideally suited for pressure vessels where the loading is quasistatic and all stresses are in equilibrium with externally applied loads. For impact events, the use of load-based criteria is less supportable. Impact events tend to be energy controlled, and thus, energy-based acceptance criteria would appear to be more appropriate. Determination of an ideal design criteria depends on what behavior is desired. Currently there is not a design criteria for inelastic analysis for RAM nation packages that is accepted by the regulatory agencies. This lack of acceptance criteria is one of the major factors in limiting the use of inelastic analysis. In this paper inelastic analysis acceptance criteria based on stress and strain-energy density will be compared for two stainless steel test units subjected to impacts onto an unyielding target. Two different material models are considered for the inelastic analysis, a bilinear fit of the stress-strain curve and a power law hardening model that very closely follows the stress-strain curve. It is the purpose of this paper to stimulate discussion and research into the area of strain-energy density based inelastic analysis acceptance criteria

Detailed performance analysis of realistic solar photovoltaic systems at extensive climatic conditions

International Nuclear Information System (INIS)

Gupta, Ankit; Chauhan, Yogesh K.

2016-01-01

In recent years, solar energy has been considered as one of the principle renewable energy source for electric power generation. In this paper, single diode photovoltaic (PV) system and double/bypass diode based PV system are designed in MATLAB/Simulink environment based on their mathematical modeling and are validated with a commercially available solar panel. The novelty of the paper is to include the effect of climatic conditions i.e. variable irradiation level, wind speed, temperature, humidity level and dust accumulation in the modeling of both the PV systems to represent a realistic PV system. The comprehensive investigations are made on both the modeled PV systems. The obtained results show the satisfactory performance for realistic models of the PV system. Furthermore, an in depth comparative analysis is carried out for both PV systems. - Highlights: • Modeling of Single diode and Double diode PV systems in MATLAB/Simulink software. • Validation of designed PV systems with a commercially available PV panel. • Acquisition and employment of key climatic factors in modeling of the PV systems. • Evaluation of main model parameters of both the PV systems. • Detailed comparative assessment of both the modeled PV system parameters.

Design criteria for XeF{sub 2} enabled deterministic transformation of bulk silicon (100) into flexible silicon layer

Energy Technology Data Exchange (ETDEWEB)

Hussain, Aftab M.; Shaikh, Sohail F.; Hussain, Muhammad M., E-mail: muhammadmustafa.hussain@kaust.edu.sa [Integrated Nanotechnology Laboratory (INL) and Integrated Disruptive Electronics Applications (IDEA) Laboratory, Computer Electrical Mathematical Science and Engineering Division, King Abdullah University of Science and Technology - KAUST, Thuwal 23955-6900 (Saudi Arabia)

2016-07-15

Isotropic etching of bulk silicon (100) using Xenon Difluoride (XeF{sub 2}) gas presents a unique opportunity to undercut and release ultra-thin flexible silicon layers with pre-fabricated state-of-the-art Complementary Metal Oxide Semiconductor (CMOS) electronics. In this work, we present design criteria and mechanism with a comprehensive mathematical model for this method. We consider various trench geometries and parametrize important metrics such as etch time, number of cycles and area efficiency in terms of the trench diameter and spacing so that optimization can be done for specific applications. From our theoretical analysis, we conclude that a honeycomb-inspired hexagonal distribution of trenches can produce the most efficient release of ultra-thin flexible silicon layers in terms of the number of etch cycles, while a rectangular distribution of circular trenches provides the most area efficient design. The theoretical results are verified by fabricating and releasing (varying sizes) flexible silicon layers. We observe uniform translation of design criteria into practice for etch distances and number of etch cycles, using reaction efficiency as a fitting parameter.

Definition of design criteria of mechanical transfer: an interaction between engineering and health areas.

Science.gov (United States)

Luz, Taciana Ramos; Echternacht, Eliza Helena de Oliveira

2012-01-01

This study aims to analyze the factors that justify the low use of a mechanical transfer in the context of a long-term institution. It is a device intended for internal transportation of individuals who have mobility problems. The analysis involves researchers from the fields of health and engineering in order to generate design criteria that consider the needs of caregivers and patients of this institution. To understand the reality of this site and their specificities, was used Ergonomic Work Analysis.

The role of advanced nuclear power technologies in developing countries: Criteria and design requirements

International Nuclear Information System (INIS)

1990-02-01

The document includes the papers presented at the following two technical committee meetings organized by the IAEA: Technical Committee Meeting and Workshop on Criteria for the Introduction of Advanced Nuclear Power Technologies for Specific Applications in Developing Countries, Vienna, 27-30 June 1988 (14 papers) and Technical Committee Meeting and Workshop on Design Requirements for the Application of Advanced Concepts in Developing Countries, Vienna, 6-9 December 1988 (16 papers). A separate abstract was prepared for each of these papers

Review of public comments on proposed seismic design criteria

International Nuclear Information System (INIS)

Philippacopoulos, A.J.; Shaukat, S.K.; Chokshi, N.C.; Bagchi, G.; Nuclear Regulatory Commission, Washington, DC; Nuclear Regulatory Commission, Washington, DC

1989-01-01

During the first quarter of 1988, the Nuclear Regulatory Commission (NRC) prepared a proposed Revision 2 to the NUREG-0800 Standard Review Plan (SRP) Sections 2.5.2 (Vibratory Ground Motion), 3.7.1 (Seismic Design Parameters), 3.7.2 (Seismic Systems Analysis) and 3.7.3 (Seismic Subsystem Analysis). The proposed Revision 2 to the SRP was a result of many years' work carried out by the NRC and the nuclear industry on the Unresolved Safety Issue (USI) A-40: ''Seismic Design Criteria.'' The background material related to NRC's efforts for resolving the A-40 issue is described in NUREG-1233. In June 1988, the proposed Revision 2 of the SRP was issued by NRC for public review and comments. Comments were received from Sargent and Lundy Engineers, Westinghouse Electric Corporation, Stevenson and Associates, Duke Power Company, General Electric Company and Electric Power Research Institute. In September 1988, Brookhaven National Laboratory (BNL) and its consultants (C.J. Costantino, R.P. Kennedy, J. Stevenson, M. Shinozuka and A.S. Veletsos) were requested to carry out a review of the comments received from the above six organizations. The objective of this review was to assist the NRC staff with the evaluation and resolution of the public comments. This review was initiated during October 1988 and it was completed on January 1989. As a result of this review, a set of modifications to the above mentioned sections of the SRP were recommended by BNL and its consultants. This paper summarizes the recommended modifications. 4 refs

Time-Dependent Deformation Modelling for a Chopped-Glass Fiber Composite for Automotive Durability Design Criteria

Energy Technology Data Exchange (ETDEWEB)

Ren, W

2001-08-24

Time-dependent deformation behavior of a polymeric composite with chopped-glass-fiber reinforcement was investigated for automotive applications, The material under stress was exposed to representative automobile service environments. Results show that environment has substantial effects on time-dependent deformation behavior of the material. The data were analyzed and experimentally-based models developed for the time-dependent deformation behavior as a basis for automotive structural durability design criteria.

Realistic methods for calculating the releases and consequences of a large LOCA

International Nuclear Information System (INIS)

Stephenson, W.; Dutton, L.M.C.; Handy, B.J.; Smedley, C.

1992-01-01

This report describes a calculational route to predict realistic radiological consequences for a successfully terminated large-loss-of-coolant accident (LOCA) at a pressurized-water reactor (PWR). All steps in the calculational route are considered. For each one, a brief comment is made on the significant differences between the methods of calculation that were identified in the benchmark studies and recommendations are made for the methods and data for carrying out realistic calculations. These are based on the best supportable methods and data and the technical basis for each recommendation is given. Where the lack of well-validated methods or data means that the most realistic method that can be justified is considered to be very conservative, the need for further research is identified. The behaviour of inorganic iodine and the removal of aerosols from the atmosphere of the reactor building are identified as areas of particular importance. Where the retention of radioactivity is sensitive to design features, these are identified and, for the most importance features, the impact of different designs on the release of activity is indicated. The predictions of the proposed model are calculated for each stage and compared with the releases of activity predicted by the licensing methods that were used in the earlier benchmark studies. The conservative nature of the latter is confirmed. Methods and data are also presented for calculating the resulting doses to members of the public of the National Radiological Protection Boards as a result of work carried out by several national bodies in the UK. Other, equally acceptable, models are used in other countries of the Community and some examples are given

Design and validation of standardized clinical and functional remission criteria in schizophrenia

Science.gov (United States)

Mosolov, Sergey N; Potapov, Andrey V; Ushakov, Uriy V; Shafarenko, Aleksey A; Kostyukova, Anastasiya B

2014-01-01

Background International Remission Criteria (IRC) for schizophrenia were developed recently by a group of internationally known experts. The IRC detect only 10%–30% of cases and do not cover the diversity of forms and social functioning. Our aim was to design a more applicable tool and validate its use – the Standardized Clinical and Functional Remission Criteria (SCFRC). Methods We used a 6-month follow-up study of 203 outpatients from two Moscow centers and another further sample of stable patients from a 1-year controlled trial of atypical versus typical medication. Diagnosis was confirmed by International Classification of Diseases Version 10 (ICD10) criteria and the Mini-International Neuropsychiatric Interview (MINI). Patients were assessed by the Positive and Negative Syndrome Scale, including intensity threshold, and further classified using the Russian domestic remission criteria and the level of social and personal functioning, according to the Personal and Social Performance Scale (PSP). The SCFRC were formulated and were validated by a data reanalysis on the first population sample and on a second independent sample (104 patients) and in an open-label prospective randomized 12-month comparative study of risperidone long-acting injectable (RLAI) versus olanzapine. Results Only 64 of the 203 outpatients (31.5%) initially met the IRC, and 53 patients (26.1%) met the IRC after 6 months, without a change in treatment. Patients who were in remission had episodic and progressive deficit (39.6%), or remittent (15%) paranoid schizophrenia, or schizoaffective disorder (17%). In addition, 105 patients of 139 (51.7%), who did not meet symptomatic IRC, remained stable within the period. Reanalysis of data revealed that 65.5% of the patients met the SCFRC. In the controlled trial, 70% of patients in the RLAI group met the SCFRC and only 19% the IRC. In the routine treatment group, 55.9% met the SCFRC and only 5.7% the IRC. Results of the further independent

Realist synthesis: illustrating the method for implementation research

Directory of Open Access Journals (Sweden)

Rycroft-Malone Jo

2012-04-01

Full Text Available Abstract Background Realist synthesis is an increasingly popular approach to the review and synthesis of evidence, which focuses on understanding the mechanisms by which an intervention works (or not. There are few published examples of realist synthesis. This paper therefore fills a gap by describing, in detail, the process used for a realist review and synthesis to answer the question ‘what interventions and strategies are effective in enabling evidence-informed healthcare?’ The strengths and challenges of conducting realist review are also considered. Methods The realist approach involves identifying underlying causal mechanisms and exploring how they work under what conditions. The stages of this review included: defining the scope of the review (concept mining and framework formulation; searching for and scrutinising the evidence; extracting and synthesising the evidence; and developing the narrative, including hypotheses. Results Based on key terms and concepts related to various interventions to promote evidence-informed healthcare, we developed an outcome-focused theoretical framework. Questions were tailored for each of four theory/intervention areas within the theoretical framework and were used to guide development of a review and data extraction process. The search for literature within our first theory area, change agency, was executed and the screening procedure resulted in inclusion of 52 papers. Using the questions relevant to this theory area, data were extracted by one reviewer and validated by a second reviewer. Synthesis involved organisation of extracted data into evidence tables, theming and formulation of chains of inference, linking between the chains of inference, and hypothesis formulation. The narrative was developed around the hypotheses generated within the change agency theory area. Conclusions Realist synthesis lends itself to the review of complex interventions because it accounts for context as well as

Design and analysis of concrete reactor vessels: New developments, problems and trends

International Nuclear Information System (INIS)

Bazant, Z.P.

1984-01-01

This lecture reviews new developments in analysis and design of prestressed concrete reactor vessels (PCRV). After a brief assessment of the current status and experience, the advantages, disadvantages, and especially the safety features of PCRV, are discussed. Attention is then focused on the design of penetrations and openings, and on the design for high-temperature resistance - areas in which further developments are needed. Various possible designs for high-temperature exposure of concrete in a hypothetical accident are analyzed. Considered are not only PCRVs for gas-cooled reactors (GCR), but also guard vessels for liquid metal fast breeder reactors (LMFBR), for which designs mitigating the adverse effects of molten sodium, molten steel, and core melt are surveyed. Realistic analysis of the problems requires further development in the knowledge of material behavior and its mathematical modeling. Recent advances in the modeling of high-temperature response of concrete, including pore water transfer, pore pressure, creep and shrinkage are outlined. This is followed by a discussion of new developments in the analysis of cracking of concrete, where the need of switching from stress criteria to energy criteria for fracture is emphasized. The lecture concludes with a brief discussion of long-time behavior, the effect of aging, and probabilistic analysis of creep. (orig.)

Sotsialistlik realist Keskküla

Index Scriptorium Estoniae

1998-01-01

Londonis 1998. a. ilmunud inglise kunstikriitiku Matthew Cullerne Bowni monograafias "Socialist Realist Painting" on eesti kunstnikest Enn Põldroos, Nikolai Kormashov, Ando Keskküla, Kormashovi ja Keskküla maalide reproduktsioonid

Realistic tissue visualization using photoacoustic image

Science.gov (United States)

Cho, Seonghee; Managuli, Ravi; Jeon, Seungwan; Kim, Jeesu; Kim, Chulhong

2018-02-01

Visualization methods are very important in biomedical imaging. As a technology that understands life, biomedical imaging has the unique advantage of providing the most intuitive information in the image. This advantage of biomedical imaging can be greatly improved by choosing a special visualization method. This is more complicated in volumetric data. Volume data has the advantage of containing 3D spatial information. Unfortunately, the data itself cannot directly represent the potential value. Because images are always displayed in 2D space, visualization is the key and creates the real value of volume data. However, image processing of 3D data requires complicated algorithms for visualization and high computational burden. Therefore, specialized algorithms and computing optimization are important issues in volume data. Photoacoustic-imaging is a unique imaging modality that can visualize the optical properties of deep tissue. Because the color of the organism is mainly determined by its light absorbing component, photoacoustic data can provide color information of tissue, which is closer to real tissue color. In this research, we developed realistic tissue visualization using acoustic-resolution photoacoustic volume data. To achieve realistic visualization, we designed specialized color transfer function, which depends on the depth of the tissue from the skin. We used direct ray casting method and processed color during computing shader parameter. In the rendering results, we succeeded in obtaining similar texture results from photoacoustic data. The surface reflected rays were visualized in white, and the reflected color from the deep tissue was visualized red like skin tissue. We also implemented the CUDA algorithm in an OpenGL environment for real-time interactive imaging.

Design and validation of standardized clinical and functional remission criteria in schizophrenia

Directory of Open Access Journals (Sweden)

Mosolov SN

2014-01-01

Full Text Available Sergey N Mosolov,1 Andrey V Potapov,1 Uriy V Ushakov,2 Aleksey A Shafarenko,1 Anastasiya B Kostyukova11Department of Mental Disorders Therapy, Moscow Research Institute of Psychiatry, Moscow, Russia; 2Moscow Psychiatric Outpatient Services #21, Moscow, RussiaBackground: International Remission Criteria (IRC for schizophrenia were developed recently by a group of internationally known experts. The IRC detect only 10%–30% of cases and do not cover the diversity of forms and social functioning. Our aim was to design a more applicable tool and validate its use – the Standardized Clinical and Functional Remission Criteria (SCFRC.Methods: We used a 6-month follow-up study of 203 outpatients from two Moscow centers and another further sample of stable patients from a 1-year controlled trial of atypical versus typical medication. Diagnosis was confirmed by International Classification of Diseases Version 10 (ICD10 criteria and the Mini-International Neuropsychiatric Interview (MINI. Patients were assessed by the Positive and Negative Syndrome Scale, including intensity threshold, and further classified using the Russian domestic remission criteria and the level of social and personal functioning, according to the Personal and Social Performance Scale (PSP. The SCFRC were formulated and were validated by a data reanalysis on the first population sample and on a second independent sample (104 patients and in an open-label prospective randomized 12-month comparative study of risperidone long-acting injectable (RLAI versus olanzapine.Results: Only 64 of the 203 outpatients (31.5% initially met the IRC, and 53 patients (26.1% met the IRC after 6 months, without a change in treatment. Patients who were in remission had episodic and progressive deficit (39.6%, or remittent (15% paranoid schizophrenia, or schizoaffective disorder (17%. In addition, 105 patients of 139 (51.7%, who did not meet symptomatic IRC, remained stable within the period. Reanalysis of

Realistic diversity loss and variation in soil depth independently affect community-level plant nitrogen use.

Science.gov (United States)

Selmants, Paul C; Zavaleta, Erika S; Wolf, Amelia A

2014-01-01

Numerous experiments have demonstrated that diverse plant communities use nitrogen (N) more completely and efficiently, with implications for how species conservation efforts might influence N cycling and retention in terrestrial ecosystems. However, most such experiments have randomly manipulated species richness and minimized environmental heterogeneity, two design aspects that may reduce applicability to real ecosystems. Here we present results from an experiment directly comparing how realistic and randomized plant species losses affect plant N use across a gradient of soil depth in a native-dominated serpentine grassland in California. We found that the strength of the species richness effect on plant N use did not increase with soil depth in either the realistic or randomized species loss scenarios, indicating that the increased vertical heterogeneity conferred by deeper soils did not lead to greater complementarity among species in this ecosystem. Realistic species losses significantly reduced plant N uptake and altered N-use efficiency, while randomized species losses had no effect on plant N use. Increasing soil depth positively affected plant N uptake in both loss order scenarios but had a weaker effect on plant N use than did realistic species losses. Our results illustrate that realistic species losses can have functional consequences that differ distinctly from randomized losses, and that species diversity effects can be independent of and outweigh those of environmental heterogeneity on ecosystem functioning. Our findings also support the value of conservation efforts aimed at maintaining biodiversity to help buffer ecosystems against increasing anthropogenic N loading.

JSFR design progress related to development of safety design criteria for Generation IV sodium-cooled fast reactors. (1) Overview

International Nuclear Information System (INIS)

Kamide, Hideki; Ando, Masato; Ito, Takaya

2015-01-01

JAEA, JAPC and MFBR have been conducting design study for the Japan Sodium-cooled Fast Reactor (JSFR), which is a design concept aiming at future commercial use as sustainable electric power source. As the result of the design study and R and D activity related the innovative technologies incorporated in the design in the Fast Reactor Cycle Technology Development (FaCT) project up to 2010, basic design concept of JSFR was established and its development process to the commercialization including construction and operation of a demonstration version of JSFR was outlined. JSFR is a looptype next generation sodium-cooled fast reactor (SFR), which is aiming at achieving development targets of Generation IV reactors concerning sustainability, safety and reliability, economics and proliferation resistance and physical protection by introducing the innovative technologies such as shortened high-chromium steel piping. The output power is assumed for the design study as 1,500 MWe for the commercial version and 750 MWe for the demonstration version. In FaCT phase I up to 2010, in order to evaluate feasibility to achieve the development targets, the design study has been conducted on the main components and systems. Since 2011, in order to contribute to the development of safety design criteria (SDC) and safety design guideline (SDG), which include the lessons learned from the TEPCO's Fukushima Dai-ichi nuclear power plants accident, in the frame work of Generation IV International Forum (GIF), the design study is focusing on the design measures against severe external events such as earthquake and tsunami. At the same time, the design study is going into detail and paying much attention to the maintenance and repair to make surer its feasibility. This paper summarizes the design concept of the demonstration version of JSFR in which progress of design work was incorporated for the safety issues on SDC and SDG of a SFR. (author)

Protocol for a realist review of workplace learning in postgraduate medical education and training.

Science.gov (United States)

Wiese, Anel; Kilty, Caroline; Bergin, Colm; Flood, Patrick; Fu, Na; Horgan, Mary; Higgins, Agnes; Maher, Bridget; O'Kane, Grainne; Prihodova, Lucia; Slattery, Dubhfeasa; Bennett, Deirdre

2017-01-19

Postgraduate medical education and training (PGMET) is a complex social process which happens predominantly during the delivery of patient care. The clinical learning environment (CLE), the context for PGMET, shapes the development of the doctors who learn and work within it, ultimately impacting the quality and safety of patient care. Clinical workplaces are complex, dynamic systems in which learning emerges from non-linear interactions within a network of related factors and activities. Those tasked with the design and delivery of postgraduate medical education and training need to understand the relationship between the processes of medical workplace learning and these contextual elements in order to optimise conditions for learning. We propose to conduct a realist synthesis of the literature to address the overarching questions; how, why and in what circumstances do doctors learn in clinical environments? This review is part of a funded projected with the overall aim of producing guidelines and recommendations for the design of high quality clinical learning environments for postgraduate medical education and training. We have chosen realist synthesis as a methodology because of its suitability for researching complexity and producing answers useful to policymakers and practitioners. This realist synthesis will follow the steps and procedures outlined by Wong et al. in the RAMESES Publication Standards for Realist Synthesis and the Realist Synthesis RAMESES Training Materials. The core research team is a multi-disciplinary group of researchers, clinicians and health professions educators. The wider research group includes experts in organisational behaviour and human resources management as well as the key stakeholders; doctors in training, patient representatives and providers of PGMET. This study will draw from the published literature and programme, and substantive, theories of workplace learning, to describe context, mechanism and outcome configurations for

Development of small reactor safety criteria in Canada

International Nuclear Information System (INIS)

Ernst, P.C.; French, P.M.; Axford, D.J.; Snell, V.G.

1990-01-01

A number of new small reactor designs have been proposed in Canada over the last several years and some have reached the stage where licensing discussions have been initiated with the Atomic Energy Control Board (AECB). An inter-organizational Small Reactor Criteria (SRC) working group was formed in 1988 to propose safety and licensing criteria for these small reactors. Two levels of criteria are proposed. The first level forms a safety philosophy and the second is a set of criteria for specific reactor applications. The safety philosophy consists of three basic safety objectives together with evaluation criteria, and fourteen fundamental principles measured by specific criteria, which must be implemented to meet the safety objectives. Two of the fourteen principles are prime: defence in depth, and safety culture; the other twelve principles can be seen as deriving from them. A benefit of this approach is that the concepts of defence in depth and safety culture become well-defined. The objectives and principles are presented in the paper and their criteria are summarized. The second level of criteria, under development, will form a safety application set and will provide small reactor criteria in a number of general areas, such as regulatory process and safety assessment, as well as for specific reactor life-cycle activities, from siting through to decommissioning. The criteria are largely deterministic. However, the frequencies and consequences of postulated accidents are assessed against numerical criteria to assist in judging the acceptability of plant design, operation, and proposed siting. All criteria proposed are designed to be testable in some evidentiary fashion, readily enabling an assessment of compliance for a given proposal

Displacement Based Seismic Design Criteria

International Nuclear Information System (INIS)

Costello, J.F.; Hofmayer, C.; Park, Y.J.

1999-01-01

The USNRC has initiated a project to determine if any of the likely revisions to traditional earthquake engineering practice are relevant to seismic design of the specialized structures, systems and components of nuclear power plants and of such significance to suggest that a change in design practice might be warranted. As part of the initial phase of this study, a literature survey was conducted on the recent changes in seismic design codes/standards, on-going activities of code-writing organizations/communities, and published documents on displacement-based design methods. This paper provides a summary of recent changes in building codes and on-going activities for future codes. It also discusses some technical issues for further consideration

Are there realistically interpretable local theories?

International Nuclear Information System (INIS)

d'Espagnat, B.

1989-01-01

Although it rests on strongly established proofs, the statement that no realistically interpretable local theory is compatible with some experimentally testable predictions of quantum mechanics seems at first sight to be incompatible with a few general ideas and clear-cut statements occurring in recent theoretical work by Griffiths, Omnes, and Ballentine and Jarrett. It is shown here that in fact none of the developments due to these authors can be considered as a realistically interpretable local theory, so that there is no valid reason for suspecting that the existing proofs of the statement in question are all flawed

Effect of combined loading on pipe flaw evaluation criteria

International Nuclear Information System (INIS)

Miura, Naoki; Chung Yeonki

1999-01-01

Considering a rational maintenance rule of Light Water Reactor piping, reliable flaw evaluation criteria are essential to determine how a detected flaw is detrimental to continuous plant operation. Ductile fracture is one of the dominant failure modes to be considered for carbon steel piping, and can be analyzed by the elastic-plastic fracture mechanics. Currently the analytical results are provided as flaw evaluation criteria using load correction factors such like the Z-factor in ASME Code Section 6. The present correction factors were conventionally determined taken a conservatism and a simplicity into account, however, the effect of internal pressure which would be an important factor under an actual plant condition was not adequately considered. Recently, a J-estimation scheme, 'LBB.ENGC' for ductile fracture analysis of circumferentially through-wall-cracked pipes subjected to combined loading was newly developed to have a better prediction with more realistic manner. This method is explicitly incorporated the contribution of both bending and tension due to internal pressure by means of the scheme compatible with an arbitrary combined loading history. In this paper, the effect of internal pressure on the flaw evaluation criteria was investigated using the new J-estimation scheme. A correction factor based on the new J-estimation scheme was compared with the present correction factors, and the predictability of the current flaw evaluation criteria was quantitatively evaluated in consideration of internal pressure. (author)

'Semi-realistic'F-term inflation model building in supergravity

International Nuclear Information System (INIS)

Kain, Ben

2008-01-01

We describe methods for building 'semi-realistic' models of F-term inflation. By semi-realistic we mean that they are built in, and obey the requirements of, 'semi-realistic' particle physics models. The particle physics models are taken to be effective supergravity theories derived from orbifold compactifications of string theory, and their requirements are taken to be modular invariance, absence of mass terms and stabilization of moduli. We review the particle physics models, their requirements and tools and methods for building inflation models

Generating realistic images using Kray

Science.gov (United States)

Tanski, Grzegorz

2004-07-01

Kray is an application for creating realistic images. It is written in C++ programming language, has a text-based interface, solves global illumination problem using techniques such as radiosity, path tracing and photon mapping.

Creating photo-realistic works in a 3D scene using layers styles to create an animation

Science.gov (United States)

Avramescu, A. M.

2015-11-01

Creating realist objects in a 3D scene is not an easy work. We have to be very careful to make the creation very detailed. If we don't know how to make these photo-realistic works, by using the techniques and a good reference photo we can create an amazing amount of detail and realism. For example, in this article there are some of these detailed methods from which we can learn the techniques necessary to make beautiful and realistic objects in a scene. More precisely, in this paper, we present how to create a 3D animated scene, mainly using the Pen Tool and Blending Options. Indeed, this work is based on teaching some simple ways of using the Layer Styles to create some great shadows, lights, textures and a realistic sense of 3 Dimension. The present work involves also showing how some interesting ways of using the illuminating and rendering options can create a realistic effect in a scene. Moreover, this article shows how to create photo realistic 3D models from a digital image. The present work proposes to present how to use Illustrator paths, texturing, basic lighting and rendering, how to apply textures and how to parent the building and objects components. We also propose to use this proposition to recreate smaller details or 3D objects from a 2D image. After a critic art stage, we are able now to present in this paper the architecture of a design method that proposes to create an animation. The aim is to create a conceptual and methodological tutorial to address this issue both scientifically and in practice. This objective also includes proposing, on strong scientific basis, a model that gives the possibility of a better understanding of the techniques necessary to create a realistic animation.

Mechanical modelling of SiC/SiC composites and design criteria

International Nuclear Information System (INIS)

Bernachy, F.; Gélébart, L.; Crépin, J.; Bornert, M.

2013-01-01

Outcomes and perspectives: • Definition of damage criteria, easy to measure and reproducible: → Useful for design purposes. • Results about the biaxial mechanical behavior of the tubes: → Construction and identification of a damage model. • Measurement of elastic properties in good agreement with multiscale simulations: → Non-linear behavior has still to be adressed using a multiscale approach. Possible strategies: - Building of a 3D homogeneous damage model of the tow; - Simulation of the initiation and propagation of cracks through the composite. • More experimental results coming to address several issues: → Non proportional tests (complex loading paths): - Investigation of crack opening/closure mechanism. → Tension-internal pressure tests: - Mechanical properties along the orthoradial direction; → Tests on other microstructures (braiding and winding angles); → Bending tests: - Test of the mechanical model and close to industrial issues

Methodology for estimating realistic responses of buildings and components under earthquake motion and its application

International Nuclear Information System (INIS)

Ebisawa, Katsumi; Abe, Kiyoharu; Kohno, Kunihiko; Nakamura, Hidetaka; Itoh, Mamoru.

1996-11-01

Failure probabilities of buildings and components under earthquake motion are estimated as conditional probabilities that their realistic responses exceed their capacities. Two methods for estimating their failure probabilities have already been developed. One is a detailed method developed in the Seismic Safety margins Research Program of Lawrence Livermore National Laboratory in U.S.A., which is called 'SSMRP method'. The other is a simplified method proposed by Kennedy et al., which is called 'Zion method'. The Zion method is sometimes called 'response factor method'. The authors adopted the response factor method. In order to enhance the estimation accuracy of failure probabilities of buildings and components, however, a new methodology for improving the response factor method was proposed. Based on the improved method, response factors of buildings and components designed to seismic design standard in Japan were estimated, and their realistic responses were also calculated. By using their realistic responses and capacities, the failure probabilities of a reactor building and relays were estimated. In order to identify the difference between new method, SSMRP method and original response factor method, the failure probabilities were compared estimated by these three methods. A similar method of SSMRP was used instead of the original SSMRP for saving time and labor. The viewpoints for selecting the methods to estimate failure probabilities of buildings and components were also proposed. (author). 55 refs

Automatic procedure for realistic 3D finite element modelling of human brain for bioelectromagnetic computations

International Nuclear Information System (INIS)

Aristovich, K Y; Khan, S H

2010-01-01

Realistic computer modelling of biological objects requires building of very accurate and realistic computer models based on geometric and material data, type, and accuracy of numerical analyses. This paper presents some of the automatic tools and algorithms that were used to build accurate and realistic 3D finite element (FE) model of whole-brain. These models were used to solve the forward problem in magnetic field tomography (MFT) based on Magnetoencephalography (MEG). The forward problem involves modelling and computation of magnetic fields produced by human brain during cognitive processing. The geometric parameters of the model were obtained from accurate Magnetic Resonance Imaging (MRI) data and the material properties - from those obtained from Diffusion Tensor MRI (DTMRI). The 3D FE models of the brain built using this approach has been shown to be very accurate in terms of both geometric and material properties. The model is stored on the computer in Computer-Aided Parametrical Design (CAD) format. This allows the model to be used in a wide a range of methods of analysis, such as finite element method (FEM), Boundary Element Method (BEM), Monte-Carlo Simulations, etc. The generic model building approach presented here could be used for accurate and realistic modelling of human brain and many other biological objects.

Access to primary care for socioeconomically disadvantaged older people in rural areas: a realist review.

Science.gov (United States)

Ford, John A; Wong, Geoff; Jones, Andy P; Steel, Nick

2016-05-17

The aim of this review is to identify and understand the contexts that effect access to high-quality primary care for socioeconomically disadvantaged older people in rural areas. A realist review. MEDLINE and EMBASE electronic databases and grey literature (from inception to December 2014). Broad inclusion criteria were used to allow articles which were not specific, but might be relevant to the population of interest to be considered. Studies meeting the inclusion criteria were assessed for rigour and relevance and coded for concepts relating to context, mechanism or outcome. An overarching patient pathway was generated and used as the basis to explore contexts, causal mechanisms and outcomes. 162 articles were included. Most were from the USA or the UK, cross-sectional in design and presented subgroup data by age, rurality or deprivation. From these studies, a patient pathway was generated which included 7 steps (problem identified, decision to seek help, actively seek help, obtain appointment, get to appointment, primary care interaction and outcome). Important contexts were stoicism, education status, expectations of ageing, financial resources, understanding the healthcare system, access to suitable transport, capacity within practice, the booking system and experience of healthcare. Prominent causal mechanisms were health literacy, perceived convenience, patient empowerment and responsiveness of the practice. Socioeconomically disadvantaged older people in rural areas face personal, community and healthcare barriers that limit their access to primary care. Initiatives should be targeted at local contextual factors to help individuals recognise problems, feel welcome, navigate the healthcare system, book appointments easily, access appropriate transport and have sufficient time with professional staff to improve their experience of healthcare; all of which will require dedicated primary care resources. Published by the BMJ Publishing Group Limited. For

Toward realistic pursuit-evasion using a roadmap-based approach

KAUST Repository

Rodriguez, Samuel; Denny, Jory; Burgos, Juan; Mahadevan, Aditya; Manavi, Kasra; Murray, Luke; Kodochygov, Anton; Zourntos, Takis; Amato, Nancy M.

2011-01-01

be applied to more realistic scenarios than are typically studied in most previous work, including agents moving in 3D environments such as terrains, multi-story buildings, and dynamic environments. We also support more realistic three-dimensional visibility

On Realistically Attacking Tor with Website Fingerprinting

Directory of Open Access Journals (Sweden)

Wang Tao

2016-10-01

Full Text Available Website fingerprinting allows a local, passive observer monitoring a web-browsing client’s encrypted channel to determine her web activity. Previous attacks have shown that website fingerprinting could be a threat to anonymity networks such as Tor under laboratory conditions. However, there are significant differences between laboratory conditions and realistic conditions. First, in laboratory tests we collect the training data set together with the testing data set, so the training data set is fresh, but an attacker may not be able to maintain a fresh data set. Second, laboratory packet sequences correspond to a single page each, but for realistic packet sequences the split between pages is not obvious. Third, packet sequences may include background noise from other types of web traffic. These differences adversely affect website fingerprinting under realistic conditions. In this paper, we tackle these three problems to bridge the gap between laboratory and realistic conditions for website fingerprinting. We show that we can maintain a fresh training set with minimal resources. We demonstrate several classification-based techniques that allow us to split full packet sequences effectively into sequences corresponding to a single page each. We describe several new algorithms for tackling background noise. With our techniques, we are able to build the first website fingerprinting system that can operate directly on packet sequences collected in the wild.

Evolving fuzzy rules for relaxed-criteria negotiation.

Science.gov (United States)

Sim, Kwang Mong

2008-12-01

In the literature on automated negotiation, very few negotiation agents are designed with the flexibility to slightly relax their negotiation criteria to reach a consensus more rapidly and with more certainty. Furthermore, these relaxed-criteria negotiation agents were not equipped with the ability to enhance their performance by learning and evolving their relaxed-criteria negotiation rules. The impetus of this work is designing market-driven negotiation agents (MDAs) that not only have the flexibility of relaxing bargaining criteria using fuzzy rules, but can also evolve their structures by learning new relaxed-criteria fuzzy rules to improve their negotiation outcomes as they participate in negotiations in more e-markets. To this end, an evolutionary algorithm for adapting and evolving relaxed-criteria fuzzy rules was developed. Implementing the idea in a testbed, two kinds of experiments for evaluating and comparing EvEMDAs (MDAs with relaxed-criteria rules that are evolved using the evolutionary algorithm) and EMDAs (MDAs with relaxed-criteria rules that are manually constructed) were carried out through stochastic simulations. Empirical results show that: 1) EvEMDAs generally outperformed EMDAs in different types of e-markets and 2) the negotiation outcomes of EvEMDAs generally improved as they negotiated in more e-markets.

Iterated interactions method. Realistic NN potential

International Nuclear Information System (INIS)

Gorbatov, A.M.; Skopich, V.L.; Kolganova, E.A.

1991-01-01

The method of iterated potential is tested in the case of realistic fermionic systems. As a base for comparison calculations of the 16 O system (using various versions of realistic NN potentials) by means of the angular potential-function method as well as operators of pairing correlation were used. The convergence of genealogical series is studied for the central Malfliet-Tjon potential. In addition the mathematical technique of microscopical calculations is improved: new equations for correlators in odd states are suggested and the technique of leading terms was applied for the first time to calculations of heavy p-shell nuclei in the basis of angular potential functions

Realistic Material Appearance Modelling

Czech Academy of Sciences Publication Activity Database

Haindl, Michal; Filip, Jiří; Hatka, Martin

2010-01-01

Roč. 2010, č. 81 (2010), s. 13-14 ISSN 0926-4981 R&D Projects: GA ČR GA102/08/0593 Institutional research plan: CEZ:AV0Z10750506 Keywords : bidirectional texture function * texture modelling Subject RIV: BD - Theory of Information http:// library .utia.cas.cz/separaty/2010/RO/haindl-realistic material appearance modelling.pdf

Criteria for maintenance and repair - LMFBR steam generators

International Nuclear Information System (INIS)

Essebaggers, J.

1975-01-01

The maintenance and repair criteria will be reviewed with respect to the designs presently under construction for the SNR-300 plant. This criteria shall be based upon the philosophy that safety and reliability are of the highest importance at all operating modes, while availability shall be maximized. To maximize the safety of the steam generator, measures have been taken to reduce the possibilities of failure by simplicity in design, choice of material, methods of fabrication and high quality assurance of critical parts of the pressure boundaries. The maintenance and repair program shall meet the same criteria or the intent of these criteria as applied for the original product. (author)

A NSSS supplier's response to differing safety criteria

International Nuclear Information System (INIS)

Cremades, J.; Filkin, R.; Franke, Th.

1980-01-01

The limited progress achieved to date in harmonizing national criteria has led to the development of designs which include the most common national requirements. Progress towards harmonization of safety criteria can be accelerated by expanding the IAEA leadership and co-ordination activities, and implementing an integrated approach to criteria development. National and International safety criteria are examined. (author)

A Radiosity Approach to Realistic Image Synthesis

Science.gov (United States)

1992-12-01

AD-A259 082 AFIT/GCE/ENG/92D-09 A RADIOSITY APPROACH TO REALISTIC IMAGE SYNTHESIS THESIS Richard L. Remington Captain, USAF fl ECTE AFIT/GCE/ENG/92D...09 SJANl 1993U 93-00134 Approved for public release; distribution unlimited 93& 1! A -A- AFIT/GCE/ENG/92D-09 A RADIOSITY APPROACH TO REALISTIC IMAGE...assistance in creating the input geometry file for the AWACS aircraft interior. Without his assistance, a good model for the diffuse radiosity implementation

Thermohydraulic simulation of HTR-10 nuclear reactor core using realistic CFD approach

International Nuclear Information System (INIS)

Silva, Alexandro S.; Dominguez, Dany S.; Mazaira, Leorlen Y. Rojas; Hernandez, Carlos R.G.; Lira, Carlos Alberto Brayner de Oliveira

2015-01-01

High-temperature gas-cooled reactors (HTGRs) have the potential to be used as possible energy generation sources in the near future, owing to their inherently safe performance by using a large amount of graphite, low power density design, and high conversion efficiency. However, safety is the most important issue for its commercialization in nuclear energy industry. It is very important for safety design and operation of an HTGR to investigate its thermal–hydraulic characteristics. In this article, it was performed the thermal–hydraulic simulation of compressible flow inside the core of the pebble bed reactor HTR (High Temperature Reactor)-10 using Computational Fluid Dynamics (CFD). The realistic approach was used, where every closely packed pebble is realistically modelled considering a graphite layer and sphere of fuel. Due to the high computational cost is impossible simulate the full core; therefore, the geometry used is a column of FCC (Face Centered Cubic) cells, with 41 layers and 82 pebbles. The input data used were taken from the thermohydraulic IAEA Benchmark (TECDOC-1694). The results show the profiles of velocity and temperature of the coolant in the core, and the temperature distribution inside the pebbles. The maximum temperatures in the pebbles do not exceed the allowable limit for this type of nuclear fuel. (author)

Criteria for the generation of spectra consistent time histories

International Nuclear Information System (INIS)

Lin, C.-W.

1977-01-01

Several methods are available to conduct seismic analysis for nuclear power plant systems and components. Among them, the response spectrum technique has been most widely adopted for linear type of modal analysis. However, for designs which consist of structural or material nonlinearites such as frequency dependent soil properties, the existance of gaps, single tie rods, and friction between supports where the response has to be computed as a function of time, time history approach is the only viable method of analysis. Two examples of time history analysis are: 1) soil-structure interaction study and, 2) a coupled reactor coolant system and building analysis to either generate the floor response specra or compute nonlinear system time history response. The generation of a suitable time history input for the analysis has been discussed in the literature. Some general guidelines are available to insure that the time history imput will be as conservative as the design response spectra. Very little has been reported as to the effect of the dyanmic characteristics of the time history input upon the system response. In fact, the only available discussion in this respect concerns only with the statitical independent nature of the time history components. In this paper, numerical results for cases using the time history approach are presented. Criteria are also established which may be advantageously used to arrive at spectra consistent time histories which are conservative and more importantly, realistic. (Auth.)

Multiobjective optimal design of runner blade using efficiency and draft tube pulsation criteria

International Nuclear Information System (INIS)

Pilev, I M; Sotnikov, A A; Rigin, V E; Semenova, A V; Cherny, S G; Chirkov, D V; Bannikov, D V; Skorospelov, V A

2012-01-01

In the present work new criteria of optimal design method for turbine runner [1] are proposed. Firstly, based on the efficient method which couples direct simulation of 3D turbulent flow and engineering semi empirical formulas, the combined method is built for hydraulic energy losses estimation in the whole turbine water passage and the efficiency criterion is formulated. Secondly, the criterion of dynamic loads minimization is developed for those caused by vortex rope precession downstream of the runner. This criterion is based on the finding that the monotonic increase of meridional velocity component in the direction to runner hub, downstream of its blades, provides for decreasing the intensity of vortex rope and thereafter, minimization of pressure pulsation amplitude. The developed algorithm was applied to optimal design of 640 MW Francis turbine runner. It can ensure high efficiency at best efficiency operating point as well as diminished pressure pulsations at full load regime.

Education Criteria for Performance Excellence, 2002.

Science.gov (United States)

National Inst. of Standards and Technology, Gaithersburg, MD.

The education criteria presented in this guide are designed to help organizations use an integrated approach to organizational performance management that results in delivery of ever-improving value to students and stakeholders. Implementation of the criteria will contribute to improvement of education quality, improvement of overall…

A realist evaluation of the management of a well-performing regional hospital in Ghana.

Science.gov (United States)

Marchal, Bruno; Dedzo, McDamien; Kegels, Guy

2010-01-25

Realist evaluation offers an interesting approach to evaluation of interventions in complex settings, but has been little applied in health care. We report on a realist case study of a well performing hospital in Ghana and show how such a realist evaluation design can help to overcome the limited external validity of a traditional case study. We developed a realist evaluation framework for hypothesis formulation, data collection, data analysis and synthesis of the findings. Focusing on the role of human resource management in hospital performance, we formulated our hypothesis around the high commitment management concept. Mixed methods were used in data collection, including individual and group interviews, observations and document reviews. We found that the human resource management approach (the actual intervention) included induction of new staff, training and personal development, good communication and information sharing, and decentralised decision-making. We identified 3 additional practices: ensuring optimal physical working conditions, access to top managers and managers' involvement on the work floor. Teamwork, recognition and trust emerged as key elements of the organisational climate. Interviewees reported high levels of organisational commitment. The analysis unearthed perceived organisational support and reciprocity as underlying mechanisms that link the management practices with commitment. Methodologically, we found that realist evaluation can be fruitfully used to develop detailed case studies that analyse how management interventions work and in which conditions. Analysing the links between intervention, mechanism and outcome increases the explaining power, while identification of essential context elements improves the usefulness of the findings for decision-makers in other settings (external validity). We also identified a number of practical difficulties and priorities for further methodological development. This case suggests that a well

A realist evaluation of the management of a well- performing regional hospital in Ghana

Directory of Open Access Journals (Sweden)

Kegels Guy

2010-01-01

Full Text Available Abstract Background Realist evaluation offers an interesting approach to evaluation of interventions in complex settings, but has been little applied in health care. We report on a realist case study of a well performing hospital in Ghana and show how such a realist evaluation design can help to overcome the limited external validity of a traditional case study. Methods We developed a realist evaluation framework for hypothesis formulation, data collection, data analysis and synthesis of the findings. Focusing on the role of human resource management in hospital performance, we formulated our hypothesis around the high commitment management concept. Mixed methods were used in data collection, including individual and group interviews, observations and document reviews. Results We found that the human resource management approach (the actual intervention included induction of new staff, training and personal development, good communication and information sharing, and decentralised decision-making. We identified 3 additional practices: ensuring optimal physical working conditions, access to top managers and managers' involvement on the work floor. Teamwork, recognition and trust emerged as key elements of the organisational climate. Interviewees reported high levels of organisational commitment. The analysis unearthed perceived organisational support and reciprocity as underlying mechanisms that link the management practices with commitment. Methodologically, we found that realist evaluation can be fruitfully used to develop detailed case studies that analyse how management interventions work and in which conditions. Analysing the links between intervention, mechanism and outcome increases the explaining power, while identification of essential context elements improves the usefulness of the findings for decision-makers in other settings (external validity. We also identified a number of practical difficulties and priorities for further

Proposed actions are no actions: re-modeling an ontology design pattern with a realist top-level ontology.

Science.gov (United States)

Seddig-Raufie, Djamila; Jansen, Ludger; Schober, Daniel; Boeker, Martin; Grewe, Niels; Schulz, Stefan

2012-09-21

Ontology Design Patterns (ODPs) are representational artifacts devised to offer solutions for recurring ontology design problems. They promise to enhance the ontology building process in terms of flexibility, re-usability and expansion, and to make the result of ontology engineering more predictable. In this paper, we analyze ODP repositories and investigate their relation with upper-level ontologies. In particular, we compare the BioTop upper ontology to the Action ODP from the NeOn an ODP repository. In view of the differences in the respective approaches, we investigate whether the Action ODP can be embedded into BioTop. We demonstrate that this requires re-interpreting the meaning of classes of the NeOn Action ODP in the light of the precepts of realist ontologies. As a result, the re-design required clarifying the ontological commitment of the ODP classes by assigning them to top-level categories. Thus, ambiguous definitions are avoided. Classes of real entities are clearly distinguished from classes of information artifacts. The proposed approach avoids the commitment to the existence of unclear future entities which underlies the NeOn Action ODP. Our re-design is parsimonious in the sense that existing BioTop content proved to be largely sufficient to define the different types of actions and plans. The proposed model demonstrates that an expressive upper-level ontology provides enough resources and expressivity to represent even complex ODPs, here shown with the different flavors of Action as proposed in the NeOn ODP. The advantage of ODP inclusion into a top-level ontology is the given predetermined dependency of each class, an existing backbone structure and well-defined relations. Our comparison shows that the use of some ODPs is more likely to cause problems for ontology developers, rather than to guide them. Besides the structural properties, the explanation of classification results were particularly hard to grasp for 'self-sufficient' ODPs as

Time-Dependent Deformation Modelling for a Chopped-Glass Fiber Composite for Automotive Durability Design Criteria; FINAL

International Nuclear Information System (INIS)

Ren, W

2001-01-01

Time-dependent deformation behavior of a polymeric composite with chopped-glass-fiber reinforcement was investigated for automotive applications, The material under stress was exposed to representative automobile service environments. Results show that environment has substantial effects on time-dependent deformation behavior of the material. The data were analyzed and experimentally-based models developed for the time-dependent deformation behavior as a basis for automotive structural durability design criteria

Functional design criteria for project W-252, phase II liquid effluent treatment and disposal. Revision 2

International Nuclear Information System (INIS)

Hatch, C.E.

1995-05-01

This document is the Functional Design Criteria for Project W-252. Project W-252 provides the scope to provide BAT/AKART (best available technology...) to 200 Liquid Effluent Phase II streams (B-Plant). This revision (Rev. 2) incorporates a major descoping of the project. The descoping was done to reflect a combination of budget cutting measures allowed by a less stringent regulatory posture toward the Phase II streams

Aspirational Model Teaching Criteria for Psychology

Science.gov (United States)

Richmond, Aaron S.; Boysen, Guy A.; Gurung, Regan A. R.; Tazeau, Yvette N.; Meyers, Steven A.; Sciutto, Mark J.

2014-01-01

In 2011, the Society for the Teaching of Psychology commissioned a presidential task force to document teaching criteria for model psychology teachers in undergraduate education. The resulting list of criteria reflects activities related to face-to-face course interaction and online teaching, training, and education; course design; implementation…

Transport properties in a monolayer graphene modulated by the realistic magnetic field and the Schottky metal stripe

Science.gov (United States)

Lu, Jian-Duo; Li, Yun-Bao; Liu, Hong-Yu; Peng, Shun-Jin; Zhao, Fei-Xiang

2016-09-01

Based on the transfer-matrix method, a systematic investigation of electron transport properties is done in a monolayer graphene modulated by the realistic magnetic field and the Schottky metal stripe. The strong dependence of the electron transmission and the conductance on the incident angle of carriers is clearly seen. The height, position as well as width of the barrier also play an important role on the electron transport properties. These interesting results are very useful for understanding the tunneling mechanism in the monolayer graphene and helpful for designing the graphene-based electrical device modulated by the realistic magnetic field and the electrical barrier.

Safety Design Criteria and Approaches to Safety Substantiation of the BN-1200

International Nuclear Information System (INIS)

Ashurko, I.

2013-01-01

Russian experience in SFR area: Activities on development of safety design criteria for SFRs of the 4th generation is carried out within the GIF framework. Although this reactor technology is considered as innovative that is relevant to the 4th generation, however, it has already a certain history. In this relation, it seems to be useful to analyze the corresponding experience that is available in various countries. 4 SFRs have been successfully operated in the USSR and in the Russian Federation: • Experimental reactor BR-5/10; • Research reactor BOR-60; • Prototype BN-350 power reactor; • Commercial BN-600 power unit at the Beloyarsk NPP. Thus, Russia gained a considerable experience of design, construction and operation of SFRs. In particular, a certain experience has been acquired on safety substantiation of reactors of this type and their licensing. Now BOR-60 and BN-600 continue their operation, BN-800 power unit is under construction, development of the commercial BN-1200 power unit, that is considered as the 4th generation reactor, has been started. Due to limited number of operating SFRs in the world, successful Russian experience in this area should be taken into account for further development and improvement of SFR SDC developed by the GIF Task Force. In particular, participation of SFR designers in this activities would be fruitful and useful

Seismic re-evaluation criteria for Bohunice V1 reconstruction

International Nuclear Information System (INIS)

Campbell, R.; Schlund, H.; Warnken, L.

2001-01-01

Bohunice V1 in Slovakia is a Russian designed two unit WWER 440, Model 230 Pressurized Water Reactor. The plant was not originally designed for earthquake. Subsequent and ongoing reassessments now confirm that the seismic hazard at the site is significant. EBO, the plant owner has contracted with a consortium lead by Siemens AG (REKON) to do major reconstruction of the plant to significantly enhance its safety systems by the addition of new systems and the upgrading of existing systems. As part of the reconstruction, a complete seismic assessment and upgrading is required for existing safety relevant structures, systems and components. It is not practical to conduct this reassessment and upgrading using criteria applied to new design of nuclear power plants. Alternate criteria may be used to achieve adequate safety goals. Utilities in the U.S. have faced several seismic issues with operating NPPs and to resolve these issues, alternate criteria have been developed which are much more cost effective than use of criteria for new design. These alternate criteria incorporate the knowledge obtained from investigation of the performance of equipment in major earthquakes and include provisions for structures and passive equipment to deform beyond the yield point, yet still provide their essential function. IAEA has incorporated features of these alternate criteria into draft Technical Guidelines for application to Bohunice V1 and V2. REKON has developed plant specific criteria and procedures for the Bohunice V1 reconstruction that incorporate major features of the U.S. developed alternate criteria, comply to local codes and which envelop the draft IAEA Technical Guidelines. Included in these criteria and procedures are comprehensive walkdown screening criteria for equipment, piping, HVAC and cable raceways, analytical criteria which include inelastic energy absorption factors defined on an element basis and testing criteria which include specific guidance on interpretation

Processing of the GALILEO fuel rod code model uncertainties within the AREVA LWR realistic thermal-mechanical analysis methodology

International Nuclear Information System (INIS)

Mailhe, P.; Barbier, B.; Garnier, C.; Landskron, H.; Sedlacek, R.; Arimescu, I.; Smith, M.; Bellanger, P.

2013-01-01

The availability of reliable tools and associated methodology able to accurately predict the LWR fuel behavior in all conditions is of great importance for safe and economic fuel usage. For that purpose, AREVA has developed its new global fuel rod performance code GALILEO along with its associated realistic thermal-mechanical analysis methodology. This realistic methodology is based on a Monte Carlo type random sampling of all relevant input variables. After having outlined the AREVA realistic methodology, this paper will be focused on the GALILEO code benchmarking process, on its extended experimental database and on the GALILEO model uncertainties assessment. The propagation of these model uncertainties through the AREVA realistic methodology is also presented. This GALILEO model uncertainties processing is of the utmost importance for accurate fuel design margin evaluation as illustrated on some application examples. With the submittal of Topical Report GALILEO to the U.S. NRC in 2013, GALILEO and its methodology are on the way to be industrially used in a wide range of irradiation conditions. (authors)

Safety design criteria for the next generation Sodium-cooled fast reactors based on lessons learned from the Fukushima NPS accident

International Nuclear Information System (INIS)

Sakai, Takaaki

2012-01-01

In this presentation, architecture of the safety design criteria as requirements for SFR system and the activities on safety research works to establish safety evaluation methods for the next generation SFRs are summarized with the basis on lessons learned from the Fukushima NPS accident. Nuclear safety is a grovel issue which should be achieved by the international cooperation. In respect of the development for the next generation reactor, it is necessary to build the harmonized safety criteria and evaluation methods to establish the next level of safety

Survey of Approaches to Generate Realistic Synthetic Graphs

Energy Technology Data Exchange (ETDEWEB)

Lim, Seung-Hwan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Lee, Sangkeun [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Powers, Sarah S [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Shankar, Mallikarjun [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Imam, Neena [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2016-10-01

A graph is a flexible data structure that can represent relationships between entities. As with other data analysis tasks, the use of realistic graphs is critical to obtaining valid research results. Unfortunately, using the actual ("real-world") graphs for research and new algorithm development is difficult due to the presence of sensitive information in the data or due to the scale of data. This results in practitioners developing algorithms and systems that employ synthetic graphs instead of real-world graphs. Generating realistic synthetic graphs that provide reliable statistical confidence to algorithmic analysis and system evaluation involves addressing technical hurdles in a broad set of areas. This report surveys the state of the art in approaches to generate realistic graphs that are derived from fitted graph models on real-world graphs.

Using technology to engage hospitalised patients in their care: a realist review.

Science.gov (United States)

Roberts, Shelley; Chaboyer, Wendy; Gonzalez, Ruben; Marshall, Andrea

2017-06-06

Patient participation in health care is associated with improved outcomes for patients and hospitals. New technologies are creating vast potential for patients to participate in care at the bedside. Several studies have explored patient use, satisfaction and perceptions of health information technology (HIT) interventions in hospital. Understanding what works for whom, under what conditions, is important when considering interventions successfully engaging patients in care. This realist review aimed to determine key features of interventions using bedside technology to engage hospital patients in their care and analyse these in terms of context, mechanisms and outcomes. A realist review was chosen to explain how and why complex HIT interventions work or fail within certain contexts. The review was guided by Pawson's realist review methodology, involving: clarifying review scope; searching for evidence; data extraction and evidence appraisal; synthesising evidence and drawing conclusions. Author experience and an initial literature scope provided insight and review questions and theories (propositions) around why interventions worked were developed and iteratively refined. A purposive search was conducted to find evidence to support, refute or identify further propositions, which formed an explanatory model. Each study was 'mined' for evidence to further develop the propositions and model. Interactive learning was the overarching theme of studies using technology to engage patients in their care. Several propositions underpinned this, which were labelled: information sharing; self-assessment and feedback; tailored education; user-centred design; and support in use of HIT. As studies were mostly feasibility or usability studies, they reported patient-centred outcomes including patient acceptability, satisfaction and actual use of HIT interventions. For each proposition, outcomes were proposed to come about by mechanisms including improved communication, shared

Repository operational criteria comparative analysis

International Nuclear Information System (INIS)

Hageman, J.P.; Chowdhury, A.H.

1994-06-01

The objective of the ''Repository Operational Criteria (ROC) Feasibility Studies'' (or ROC task) was to conduct comprehensive and integrated analyses of repository design, construction, and operations criteria in 10 CFR Part 60 regulations considering the interfaces among the components of the regulations and impacts of any potential changes to those regulations. The ROC task addresses regulatory criteria and uncertainties related to the preclosure aspects of the geologic repository. Those parts of 10 CFR Part 60 that require routine guidance or minor changes to the rule were addressed in Hageman and Chowdhury, 1992. The ROC task shows a possible need for further regulatory clarity, by major changes to the rule, related to the design bases and siting of a geologic repository operations area and radiological emergency planning in order to assure defense-in-depth. The analyses, presented in this report, resulted in the development and refinement of regulatory concepts and their supporting rationale for recommendations for potential major changes to 10 CFR Pan 0 regulations

Investigation on Stress-Rupture Behavior of a Chopped-Glass-Fiber Composite for Automotive Durability Design Criteria

Energy Technology Data Exchange (ETDEWEB)

Ren, W

2001-08-24

Practical and inexpensive testing methods were developed to investigate stress-rupture properties of a polymeric composite with chopped glass fiber reinforcement for automotive applications. The material was tested in representative automotive environments to generate experimental data. The results indicate that environments have substantial effects on the stress-rupture behavior. The data were analyzed and developed into stress-rupture design criteria to address one of the durability aspects of the material for automotive structural applications.

A Low-cost System for Generating Near-realistic Virtual Actors

Science.gov (United States)

Afifi, Mahmoud; Hussain, Khaled F.; Ibrahim, Hosny M.; Omar, Nagwa M.

2015-06-01

Generating virtual actors is one of the most challenging fields in computer graphics. The reconstruction of a realistic virtual actor has been paid attention by the academic research and the film industry to generate human-like virtual actors. Many movies were acted by human-like virtual actors, where the audience cannot distinguish between real and virtual actors. The synthesis of realistic virtual actors is considered a complex process. Many techniques are used to generate a realistic virtual actor; however they usually require expensive hardware equipment. In this paper, a low-cost system that generates near-realistic virtual actors is presented. The facial features of the real actor are blended with a virtual head that is attached to the actor's body. Comparing with other techniques that generate virtual actors, the proposed system is considered a low-cost system that requires only one camera that records the scene without using any expensive hardware equipment. The results of our system show that the system generates good near-realistic virtual actors that can be used on many applications.

Problem Posing with Realistic Mathematics Education Approach in Geometry Learning

Science.gov (United States)

Mahendra, R.; Slamet, I.; Budiyono

2017-09-01

One of the difficulties of students in the learning of geometry is on the subject of plane that requires students to understand the abstract matter. The aim of this research is to determine the effect of Problem Posing learning model with Realistic Mathematics Education Approach in geometry learning. This quasi experimental research was conducted in one of the junior high schools in Karanganyar, Indonesia. The sample was taken using stratified cluster random sampling technique. The results of this research indicate that the model of Problem Posing learning with Realistic Mathematics Education Approach can improve students’ conceptual understanding significantly in geometry learning especially on plane topics. It is because students on the application of Problem Posing with Realistic Mathematics Education Approach are become to be active in constructing their knowledge, proposing, and problem solving in realistic, so it easier for students to understand concepts and solve the problems. Therefore, the model of Problem Posing learning with Realistic Mathematics Education Approach is appropriately applied in mathematics learning especially on geometry material. Furthermore, the impact can improve student achievement.

Development of Design Criteria for Fluid Induced Structural Vibrations in Steam Generators and Heat Exchangers

International Nuclear Information System (INIS)

Uvan Catton; Dhir, Vijay K.; Deepanjan Mitra; Omar Alquaddoomi; Pierangelo Adinolfi

2004-01-01

Flow-induced vibration in heat exchangers has been a major cause of concern in the nuclear industry for several decades. Many incidents of failure of heat exchangers due to apparent flow-induced vibration have been reported through the USNRC incident reporting system. Almost all heat exchangers have to deal with this problem during their operation. The phenomenon has been studied since the 1970s and the database of experimental studies on flow-induced vibration is constantly updated with new findings and improved design criteria for heat exchangers

The Non-absoluteness of the Leading Position of the Frequency ——On the Vocabulary Design Criteria of Teaching Chinese to Speakers of Other Language

Directory of Open Access Journals (Sweden)

Ma Qinghua

2017-10-01

Full Text Available The design criteria of the vocabulary outline of the second language teaching vary according to the teaching objectives. Under the same objective, the criteria are often more than one. The multiple criteria are sometimes compatible and sometimes conflicting. Through analyzing and evaluating the advantages and disadvantages of the new Chinese Proficiency Test (HSK Vocabulary Outline, this paper reveals the interactions between the task objectives, the criterion conditions and processing strategies, as well as the interaction relationships between the multiple criteria features of the vocabulary outline designing process, and then abstracts the general principles and overall rules. The research results subvert the habitual knowledge that the frequency criterion position ranked first, which is always popular at least in the Chinese academic circle. It finds that the leading position of frequency criterion only exists in the criteria compatibility model. In the conflict model of the locutionary criteria, the stylistic criterion and syntactic criterion are strong criteria, while the word frequency criterion relegates to the weak position. In the conflict model of the locutionary and illocutionary criteria, the illocutionary criterion is strong criterion, while the locutionary criterion relegates to the weak position, which indicates that the language can’t be above its purpose of usage. This research is conducive to the improvement of the vocabulary outline. It also has certain practical significance to the disciplinary theories of Teaching Chinese to Speakers of Other Language or even to the whole second language teaching.

Should scientific realists be platonists?

DEFF Research Database (Denmark)

Busch, Jacob; Morrison, Joe

2015-01-01

an appropriate use of the resources of Scientific Realism (in particular, IBE) to achieve platonism? (§2) We argue that just because a variety of different inferential strategies can be employed by Scientific Realists does not mean that ontological conclusions concerning which things we should be Scientific...

Criteria for designing an interim waste storage facility

International Nuclear Information System (INIS)

Vicente, Roberto

2011-01-01

The long-lived radioactive wastes with activity above clearance levels generated by radioisotope users in Brazil are collected into centralized waste storage facilities under overview of the National Commission on Nuclear Energy (CNEN). One of these centers is the Radioactive Waste Management Department (GRR) at the Nuclear and Energy Research Institute (IPEN), in Sao Paulo, which since 1978 also manages the wastes generated by IPEN itself. Present inventory of stored wastes includes about 160 tons of treated wastes, distributed in 1290 steel, 200-liters drums, and 52 steel, 1.6 m 3 -boxes, with an estimated total activity of 0.8 TBq. Radionuclides present in these wastes are fission and activation products, transuranium elements, and isotopes from the uranium and thorium decay series. The capacity and quality of the storage rooms at GRR evolved along the last decades to meet the requirements set forth by the Brazilian regulatory authorities.From a mere outdoor concrete platform over which drums were simply stacked and covered with canvas to the present day building, a great progress was made in the storage method. In this paper we present the results of a study in the criteria that were meant to guide the design of the storage building, many of which were eventually adopted in the final concept, and are now built-in features of the facility. We also present some landmarks in the GRR's activities related to waste management in general and waste storage in particular, until the treated wastes of IPEN found their way into the recently licensed new storage facility. (author)

Modeling and Analysis of Realistic Fire Scenarios in Spacecraft

Science.gov (United States)

Brooker, J. E.; Dietrich, D. L.; Gokoglu, S. A.; Urban, D. L.; Ruff, G. A.

2015-01-01

An accidental fire inside a spacecraft is an unlikely, but very real emergency situation that can easily have dire consequences. While much has been learned over the past 25+ years of dedicated research on flame behavior in microgravity, a quantitative understanding of the initiation, spread, detection and extinguishment of a realistic fire aboard a spacecraft is lacking. Virtually all combustion experiments in microgravity have been small-scale, by necessity (hardware limitations in ground-based facilities and safety concerns in space-based facilities). Large-scale, realistic fire experiments are unlikely for the foreseeable future (unlike in terrestrial situations). Therefore, NASA will have to rely on scale modeling, extrapolation of small-scale experiments and detailed numerical modeling to provide the data necessary for vehicle and safety system design. This paper presents the results of parallel efforts to better model the initiation, spread, detection and extinguishment of fires aboard spacecraft. The first is a detailed numerical model using the freely available Fire Dynamics Simulator (FDS). FDS is a CFD code that numerically solves a large eddy simulation form of the Navier-Stokes equations. FDS provides a detailed treatment of the smoke and energy transport from a fire. The simulations provide a wealth of information, but are computationally intensive and not suitable for parametric studies where the detailed treatment of the mass and energy transport are unnecessary. The second path extends a model previously documented at ICES meetings that attempted to predict maximum survivable fires aboard space-craft. This one-dimensional model implies the heat and mass transfer as well as toxic species production from a fire. These simplifications result in a code that is faster and more suitable for parametric studies (having already been used to help in the hatch design of the Multi-Purpose Crew Vehicle, MPCV).

Identifying the connective strength between model parameters and performance criteria

Directory of Open Access Journals (Sweden)

B. Guse

2017-11-01

is found for low- and mid-flow conditions. Moreover, the RT analyses emphasise the benefit of an individual analysis of the three components of KGE and of the FDC segments. Furthermore, the RT analyses highlight under which conditions these performance criteria provide insights into precise parameter identification. Our results show that separate performance criteria are required to identify dominant parameters on low- and mid-flow conditions, whilst the number of required performance criteria for high flows increases with increasing process complexity in the catchment. Overall, the analysis of the connective strength between model parameters and performance criteria using RTs contribute to a more realistic handling of parameters and performance criteria in hydrological modelling.

Value/impact of design criteria for cast ductile iron shipping casks

International Nuclear Information System (INIS)

1983-01-01

The ductile failure criteria proposed in the Base report appear appropriate except that stress intensity values, S/sub m/ should be based on lower safety factors and ductility should be added as a criterion. A safety factor for stress intensity, s/sub m/ of 4 is recommended rather than 3 on minimum ultimate tensile strength, S/sub u/ in accordance with ASME code philosophy of assigning higher safety factors to cast ductile iron than to steel. This more conservative approach has no impact on costs since the selection of wall thickness is controlled by shielding rather than by stress considerations. The addition of a ductility criterion is recommended because of the problems associated with the selection of appropriate brittle failure criteria and the potential for cast ductile iron to have extremely low elongation at failure. Neither a materials nor a linear elastic fracture mechanics (LEFM) approach appear to be viable for demonstrating the prevention of brittle failure in cast ductile iron shipping casks. It is possible that the analytic methods predict brittle failure because of extremely conservative assumptions whereas real casks may not fail. Model drop tests could be used to demonstrate containment integrity. It is estimated that a risk committment of at least $1,000,000 would be required for engineering, design, model fabrication and testing. Before taking such risks, a mechanism should be found to obtain concurrence from NRC that the results of the test would be acceptable. Probabilistic approaches or model testing could be used to demonstrate the acceptability of cast ductile iron casks from a brittle failure point of view. Before probabilistic methods can be used, the NRC would have to be persuaded to accept the approach of the Competent Authority in West Germany or more formalized methods for probabilistic risk assessments

Time management: a realistic approach.

Science.gov (United States)

Jackson, Valerie P

2009-06-01

Realistic time management and organization plans can improve productivity and the quality of life. However, these skills can be difficult to develop and maintain. The key elements of time management are goals, organization, delegation, and relaxation. The author addresses each of these components and provides suggestions for successful time management.

Triangulating and guarding realistic polygons

NARCIS (Netherlands)

Aloupis, G.; Bose, P.; Dujmovic, V.; Gray, C.M.; Langerman, S.; Speckmann, B.

2008-01-01

We propose a new model of realistic input: k-guardable objects. An object is k-guardable if its boundary can be seen by k guards in the interior of the object. In this abstract, we describe a simple algorithm for triangulating k-guardable polygons. Our algorithm, which is easily implementable, takes

Regulatory Safety Issues in the Structural Design Criteria of ASME Section III Subsection NH and for Very High Temperatures for VHTR & GEN IV

Energy Technology Data Exchange (ETDEWEB)

William J. O’Donnell; Donald S. Griffin

2007-05-07

The objective of this task is to identify issues relevant to ASME Section III, Subsection NH [1], and related Code Cases that must be resolved for licensing purposes for VHTGRs (Very High Temperature Gas Reactor concepts such as those of PBMR, Areva, and GA); and to identify the material models, design criteria, and analysis methods that need to be added to the ASME Code to cover the unresolved safety issues. Subsection NH was originally developed to provide structural design criteria and limits for elevated-temperature design of Liquid Metal Fast Breeder Reactor (LMFBR) systems and some gas-cooled systems. The U.S. Nuclear Regulatory Commission (NRC) and its Advisory Committee for Reactor Safeguards (ACRS) reviewed the design limits and procedures in the process of reviewing the Clinch River Breeder Reactor (CRBR) for a construction permit in the late 1970s and early 1980s, and identified issues that needed resolution. In the years since then, the NRC and various contractors have evaluated the applicability of the ASME Code and Code Cases to high-temperature reactor designs such as the VHTGRs, and identified issues that need to be resolved to provide a regulatory basis for licensing. This Report describes: (1) NRC and ACRS safety concerns raised during the licensing process of CRBR , (2) how some of these issues are addressed by the current Subsection NH of the ASME Code; and (3) the material models, design criteria, and analysis methods that need to be added to the ASME Code and Code Cases to cover unresolved regulatory issues for very high temperature service.

Safety and reliability criteria

International Nuclear Information System (INIS)

O'Neil, R.

1978-01-01

Nuclear power plants and, in particular, reactor pressure boundary components have unique reliability requirements, in that usually no significant redundancy is possible, and a single failure can give rise to possible widespread core damage and fission product release. Reliability may be required for availability or safety reasons, but in the case of the pressure boundary and certain other systems safety may dominate. Possible Safety and Reliability (S and R) criteria are proposed which would produce acceptable reactor design. Without some S and R requirement the designer has no way of knowing how far he must go in analysing his system or component, or whether his proposed solution is likely to gain acceptance. The paper shows how reliability targets for given components and systems can be individually considered against the derived S and R criteria at the design and construction stage. Since in the case of nuclear pressure boundary components there is often very little direct experience on which to base reliability studies, relevant non-nuclear experience is examined. (author)

Critical reflections on realist review: insights from customizing the methodology to the needs of participatory research assessment.

Science.gov (United States)

Jagosh, Justin; Pluye, Pierre; Wong, Geoff; Cargo, Margaret; Salsberg, Jon; Bush, Paula L; Herbert, Carol P; Green, Lawrence W; Greenhalgh, Trish; Macaulay, Ann C

2014-06-01

Realist review has increased in popularity as a methodology for complex intervention assessment. Our experience suggests that the process of designing a realist review requires its customization to areas under investigation. To elaborate on this idea, we first describe the logic underpinning realist review and then present critical reflections on our application experience, organized in seven areas. These are the following: (1) the challenge of identifying middle range theory; (2) addressing heterogeneity and lack of conceptual clarity; (3) the challenge of appraising the quality of complex evidence; (4) the relevance of capturing unintended outcomes; (5) understanding the process of context, mechanism, and outcome (CMO) configuring; (6) incorporating middle-range theory in the CMO configuration process; and (7) using middle range theory to advance the conceptualization of outcomes - both visible and seemingly 'hidden'. One conclusion from our experience is that the degree of heterogeneity of the evidence base will determine whether theory can drive the development of review protocols from the outset, or will follow only after an intense period of data immersion. We hope that presenting a critical reflection on customizing realist review will convey how the methodology can be tailored to the often complex and idiosyncratic features of health research, leading to innovative evidence syntheses. Copyright © 2013 John Wiley & Sons, Ltd.

Reliability-based econometrics of aerospace structural systems: Design criteria and test options. Ph.D. Thesis - Georgia Inst. of Tech.

Science.gov (United States)

Thomas, J. M.; Hanagud, S.

1974-01-01

The design criteria and test options for aerospace structural reliability were investigated. A decision methodology was developed for selecting a combination of structural tests and structural design factors. The decision method involves the use of Bayesian statistics and statistical decision theory. Procedures are discussed for obtaining and updating data-based probabilistic strength distributions for aerospace structures when test information is available and for obtaining subjective distributions when data are not available. The techniques used in developing the distributions are explained.

Review of design criteria and safety analysis of safety class electric building for fuel test loop

Energy Technology Data Exchange (ETDEWEB)

Kim, J. Y.

1998-02-01

Steady state fuel test loop will be equipped in HANARO to obtain the development and betterment of advanced fuel and materials through the irradiation tests. HANARO fuel test loop was designed for CANDU and PWR fuel testing. Safety related system of Fuel Test Loop such as emergency cooling water system, component cooling water system, safety ventilation system, high energy line break mitigation system and remote control room was required 1E class electric supply to meet the safety operation in accordance with related code. Therefore, FTL electric building was designed to construction and install the related equipment based on seismic category I. The objective of this study is to review the design criteria and analysis the safety function of safety class electric building for fuel test loop, and this results will become guidance for the irradiation testing in future. (author). 10 refs., 6 tabs., 30 figs.

Basic design criteria for an impact test frame for safety glazing; Criterios basicos de diseno de banco de ensayos para impactos de vidrios de seguridad

Energy Technology Data Exchange (ETDEWEB)

Postigo, S.; Pacios, A.; Huerta, C.

2011-07-01

The Spanish Building Code establishes the essential requirements of safety and habitability that buildings must satisfy. The Basic Document of Safety in Use and Accessibility identifies some critical areas where falling through brittle elements may cause a risk to the user. The document also establishes the minimum performance of glasses located in such areas, according to the impact procedure described in UNE-EN 12600:2003. However, this standard does not provide detailed information about the characteristics of the test equipment, but indicates a final calibration as validation test. The general criteria and conditions of this calibration are also incorporated in the UNE-EN 12600. To better achieve a successful manufacture of a pendulum complying with calibration limits, a proposal of the basic design criteria of a test frame for impacts of safety glazing is presented in this paper. Prototypes and results have been evaluated using dynamic design criteria of the impact phenomenon. Three criteria proposed and applied in the design and manufacture of a real test frame have helped to achieve the calibration required by the UNE-EN 12600:2003. The repeatability and reproducibility of the tests presented in this paper also guaranty the robustness of the set-up. (Author)

NWTS program criteria for mined geologic disposal of nuclear waste: repository performance and development criteria. Public draft

Energy Technology Data Exchange (ETDEWEB)

None

1982-07-01

This document, DOE/NWTS-33(3) is one of a series of documents to establish the National Waste Terminal Storage (NWTS) program criteria for mined geologic disposal of high-level radioactive waste. For both repository performance and repository development it delineates the criteria for design performance, radiological safety, mining safety, long-term containment and isolation, operations, and decommissioning. The US Department of Energy will use these criteria to guide the development of repositories to assist in achieving performance and will reevaluate their use when the US Nuclear Regulatory Commission issues radioactive waste repository rules.

NWTS program criteria for mined geologic disposal of nuclear waste: repository performance and development criteria. Public draft

International Nuclear Information System (INIS)

1982-07-01

This document, DOE/NWTS-33(3) is one of a series of documents to establish the National Waste Terminal Storage (NWTS) program criteria for mined geologic disposal of high-level radioactive waste. For both repository performance and repository development it delineates the criteria for design performance, radiological safety, mining safety, long-term containment and isolation, operations, and decommissioning. The US Department of Energy will use these criteria to guide the development of repositories to assist in achieving performance and will reevaluate their use when the US Nuclear Regulatory Commission issues radioactive waste repository rules

Optimization Criteria In Design Of Seismic Isolated Building

International Nuclear Information System (INIS)

Clemente, Paolo; Buffarini, Giacomo

2008-01-01

Use of new anti-seismic techniques is certainly suitable for buildings of strategic importance and, in general, in the case of very high risk. For ordinary buildings, instead, the cost of base isolation system should be balanced by an equivalent saving in the structure. The comparison criteria have been first defined, then a large numerical investigation has been carried out to analyze the effectiveness and the economic suitability of seismic isolation in concrete buildings

Review of design criteria for Criticality Accident Alarm System (CAAS) used in Fuel Reprocessing Facility

International Nuclear Information System (INIS)

Chandrasekaran, S.; Basu, Pew; Sivasubramaniyan, K.; Venkatraman, B.

2016-01-01

Though fuel cycle facilities handling fissile materials are designed with careful criticality safety analysis, the criticality accident cannot be ruled out completely. Criticality Accident Alarm System (CAAS) is being installed as part of criticality safety management in fuel cycle facilities. CAAS system being used in India, is ECIL make, ionization chamber based gamma detector, which houses three identical detectors and works on 2/3 logic. As per ISO 7753 and ANSI/ANS-8.3, the CAAS must be designed to be capable of detecting any minimum accident occurs which could be of concern. Based on this, alarm limit used in CAAS is: 4 R/h (fast transient excursion) and 3 mR in 0.5 sec (slow excursion). In case of reprocessing facilities wherein process tanks located in heavy shielding, identification of CAAS installation locations require detailed radiation transport calculations. A study has been taken to estimate the gamma dose rate from thick concrete hot cells in order to determine the locations of CAAS to meet the present design criteria of alarm limit

Fuel safety criteria and review by OECD / CSNI task force

International Nuclear Information System (INIS)

Van Doesburg, W.

1999-01-01

Full text of publication follows: with the advent of advanced fuel and core designs, and the implementation of more accurate (best estimate or statistical) design and analysis methods, there is a general feeling that safety margins have been or are being reduced. Historically, fuel safety margins were defined by adding conservatism to the safety limits, which in turn were also fixed in a conservative manner, here, the expression 'conservatism' expresses the fact that bounding or limiting numbers were chosen for model parameters, plant and fuel design data, and fuel operating history values. Unfortunately, as these conservatisms were not quantified (or quantifiable), the amount of safety available or the reduction thereof is difficult to substantiate. For the regulator, it is important to know the margin available with the utilities' request for approval of new fuel or methods; likewise, for the utility and vendor it is important to know what margins exist and what they are based on, to identify in which direction they can make further progress and optimize fuel and fuel cycle cost. Naturally, each party involved will have to decide on how much margin should be in place, to establish operational criteria and ensure that these can actually be met during operation. To assess the margins issue, safety criteria themselves need to be reviewed first. Most - if not all - of the currently existing safety criteria were established during the 60's and early 70's, and verified against experiments with fuel available at that time - mostly at zero exposure. Of course, verification was performed as designs progressed in later years, primarily with the aim to be able to prove that safety criteria were adequate as long as the said conservatisms would be retained, and not with the aim to reestablish limits. The mandate to the OECD/CSNI/PWG2 Task Force on Fuel Safety Criteria (TFFSC) is to assess the adequacy of existing fuel safety criteria, in view of the 'new design' elements (new

Investigation on Stress-Rupture Behavior of a Chopped-Glass-Fiber Composite for Automotive Durability Design Criteria; FINAL

International Nuclear Information System (INIS)

Ren, W

2001-01-01

Practical and inexpensive testing methods were developed to investigate stress-rupture properties of a polymeric composite with chopped glass fiber reinforcement for automotive applications. The material was tested in representative automotive environments to generate experimental data. The results indicate that environments have substantial effects on the stress-rupture behavior. The data were analyzed and developed into stress-rupture design criteria to address one of the durability aspects of the material for automotive structural applications

The Examination of The Main Transportation Arteries of Konya In Terms of Landscape Architecture Design Criteria

Directory of Open Access Journals (Sweden)

Sertaç Güngör

2017-04-01

Full Text Available Ensuring comfort of use and security of pedestrians, which are the main users of urban green spaces, and the determination of their needs are important since local authorities are guiding for new pedestrian zone studies in the Konya city. Because of the problems caused by the upper structure, the necessary care is not given in terms of transportation comfort, pedestrian safety, vehicle security, plant design and ergonomic / antropemetric standards. The pedestrian way and refuge landscape designs have an important position and amount among open green areas on the scale of Konya. However, it was identified that the applications conducted were inadequate in terms of aesthetic and functional characteristics and were not suitable for the urban landscape design principles, in general, and the standards of urban afforestation of the streets. In this study, the current situation of 3 main streets of Konya used most intensely was examined in terms of landscape design criteria and some suggestions were made by attempting to identify the improvement works that should be performed by the public authorities.

Factors influencing intercultural doctor-patient communication: a realist review.

Science.gov (United States)

Paternotte, Emma; van Dulmen, Sandra; van der Lee, Nadine; Scherpbier, Albert J J A; Scheele, Fedde

2015-04-01

Due to migration, doctors see patients from different ethnic backgrounds. This causes challenges for the communication. To develop training programs for doctors in intercultural communication (ICC), it is important to know which barriers and facilitators determine the quality of ICC. This study aimed to provide an overview of the literature and to explore how ICC works. A systematic search was performed to find literature published before October 2012. The search terms used were cultural, communication, healthcare worker. A realist synthesis allowed us to use an explanatory focus to understand the interplay of communication. In total, 145 articles met the inclusion criteria. We found ICC challenges due to language, cultural and social differences, and doctors' assumptions. The mechanisms were described as factors influencing the process of ICC and divided into objectives, core skills and specific skills. The results were synthesized in a framework for the development of training. The quality of ICC is influenced by the context and by the mechanisms. These mechanisms translate into practical points for training, which seem to have similarities with patient-centered communication. Training for improving ICC can be developed as an extension of the existing training for patient-centered communication. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Suppression criteria of parasitic mode oscillations in a gyrotron beam tunnel

Science.gov (United States)

Kumar, Nitin; Singh, Udaybir; Singh, T. P.; Sinha, A. K.

2011-02-01

This paper presents the design criteria of the parasitic mode oscillations suppression for a periodic, ceramic, and copper loaded gyrotron beam tunnel. In such a type of beam tunnel, the suppression of parasitic mode oscillations is an important design problem. A method of beam-wave coupling coefficient and its mathematical formulation are presented. The developed design criteria are used in the beam tunnel design of a 42 GHz gyrotron to be developed for the Indian TOKAMAK system. The role of the thickness and the radius of the beam tunnel copper rings to obtain the developed design criteria are also discussed. The commercially available electromagnetic code CST and the electron trajectory code EGUN are used for the simulations.

Suppression criteria of parasitic mode oscillations in a gyrotron beam tunnel

International Nuclear Information System (INIS)

Kumar, Nitin; Singh, Udaybir; Sinha, A. K.; Singh, T. P.

2011-01-01

This paper presents the design criteria of the parasitic mode oscillations suppression for a periodic, ceramic, and copper loaded gyrotron beam tunnel. In such a type of beam tunnel, the suppression of parasitic mode oscillations is an important design problem. A method of beam-wave coupling coefficient and its mathematical formulation are presented. The developed design criteria are used in the beam tunnel design of a 42 GHz gyrotron to be developed for the Indian TOKAMAK system. The role of the thickness and the radius of the beam tunnel copper rings to obtain the developed design criteria are also discussed. The commercially available electromagnetic code CST and the electron trajectory code EGUN are used for the simulations.

ASSESSMENT OF THE RELEVANCE OF DISPLACEMENT BASED DESIGN METHODS/CRITERIA TO NUCLEAR PLANT STRUCTURES

International Nuclear Information System (INIS)

HOFMAYER, C.; MILLER, C.; WANG, Y.; COSTELLO, J.

2001-01-01

Revisions to the USNRC Regulatory Guides and Standard Review Plan Sections devoted to earthquake engineering practice are currently in process. The intent is to reflect changes in engineering practice that have evolved in the twenty years that have passed since those criteria were originally published. Additionally, field observations of the effects of the Northridge (1994) and Kobe (1995) earthquakes have inspired some reassessment in the technical community about certain aspects of design practice. In particular, questions have arisen about the effectiveness of basing earthquake resistant designs on resistance to seismic forces and, then evaluating tolerability of the expected displacements. Therefore, a research effort was undertaken to examine the implications for NRC's seismic practice of the move, in the earthquake engineering community, toward using expected displacement rather than force (or stress) as the basis for assessing design adequacy. The results of the NRC sponsored research on this subject are reported in this paper. A slow trend toward the utilization of displacement based methods for design was noted. However, there is a more rapid trend toward the use of displacement based methods for seismic evaluation of existing facilities. A document known as FEMA 273, has been developed and is being used as the basis for the design of modifications to enhance the seismic capability of existing non-nuclear facilities. The research concluded that displacement based methods, such as given in FEMA 273, may be useful for seismic margin studies of existing nuclear power stations. They are unlikely to be useful for the basic design of new stations since nuclear power stations are designed to remain elastic during a seismic event. They could, however, be useful for estimating the margins associated with that design

Evaluation of proposed German safety criteria for high-temperature gas-cooled reactors

International Nuclear Information System (INIS)

Barsell, A.W.

1980-05-01

This work reviews proposed safety criteria prepared by the German Bundesministerium des Innern (BMI) for future licensing of gas-cooled high-temperature reactor (HTR) concepts in the Federal Republic of Germany. Comparison is made with US General Design Criteria (GDCs) in 10CFR50 Appendix A and with German light water reactor (LWR) criteria. Implications for the HTR design relative to the US design and safety approach are indicated. Both inherent characteristics and design features of the steam cycle, gas turbine, and process heat concepts are taken into account as well as generic design options such as a pebble bed or prismatic core

Investigation of the Stress Intensity Limits of ASME Section III Div.5 for Structure Design Criteria of SFR Fuel Assembly

Energy Technology Data Exchange (ETDEWEB)

Choo, Jin-Yup; Kim, Hyung-Kyu; Cheon, Jin-Sik [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

These affect the mechanical design of the fuel assembly components. And thus, appropriate structural design criteria should also be chosen to incorporate the specific design conditions of the SFR fuel assemblies. Among them, the temperature is one of the most crucial conditions to be concerned because the sodium coolant temperature is normally more than 500ºC which is much higher than that of the LWR (< 350ºC). This implies that a thermal creep should be significantly considered in the SFR fuel assembly mechanical design. In addition to the high temperature condition, an irradiation swelling is also an important behavior that the SFR fuel assembly material should accommodate. To incorporate the temperature and irradiation impacts, the material of the fuel assembly components is presently determined to be made of HT-9, the ferriticmartensitic steel. In this paper, the ASME Sec. III Div. 5 (referred to as ‘Div. 5’ hereinafter), which was developed for a ‘high temperature reactor’, is considered as one of the structural design criteria for the mechanical design of SFR fuel assemblies. In this paper, the stress intensity limits, S{sub m} and S{sub t} of HT-9 were built for the structural criteria of an SFR fuel assembly. S{sub m} is obtained from the ultimate strength. As for S{sub t}, it is more complicated because of its dependency of time duration in addition to temperature. Following the definition of S{sub mt}, the method in the ASME Sec. III Div. 1, Subsec. NH was consulted. We found that the Sm is adopted as S{sub mt} under the temperature about 470ºC which is relatively low temperature range and over 470ºC with relatively short time duration as 1000 hours. And the S{sub t} is adopted as Smt at over 470ºC and long time duration over 34800 hours, and over 520ºC and 10{sup 4} hours too. And at over 570ºC and 1000 hours, and at over 630ºC and 100 hours, S{sub t} is also adopted for S{sub mt}.

Separable expansion for realistic multichannel scattering problems

International Nuclear Information System (INIS)

Canton, L.; Cattapan, G.; Pisent, G.

1987-01-01

A new approach to the multichannel scattering problem with realistic local or nonlocal interactions is developed. By employing the negative-energy solutions of uncoupled Sturmian eigenvalue problems referring to simple auxiliary potentials, the coupling interactions appearing to the original multichannel problem are approximated by finite-rank potentials. By resorting to integral-equation tecniques the coupled-channel equations are then reduced to linear algebraic equations which can be straightforwardly solved. Compact algebraic expressions for the relevant scattering matrix elements are thus obtained. The convergence of the method is tasted in the single-channel case with realistic optical potentials. Excellent agreement is obtained with a few terms in the separable expansion for both real and absorptive interactions

Regulatory Safety Issues in the Structural Design Criteria of ASME Section III Subsection NH and for Very High Temperatures for VHTR and GEN IV

International Nuclear Information System (INIS)

O'Donnell, William J.; Griffin, Donald S.

2007-01-01

The objective of this task is to identify issues relevant to ASME Section III, Subsection NH [1], and related Code Cases that must be resolved for licensing purposes for VHTGRs (Very High Temperature Gas Reactor concepts such as those of PBMR, Areva, and GA); and to identify the material models, design criteria, and analysis methods that need to be added to the ASME Code to cover the unresolved safety issues. Subsection NH was originally developed to provide structural design criteria and limits for elevated-temperature design of Liquid Metal Fast Breeder Reactor (LMFBR) systems and some gas-cooled systems. The U.S. Nuclear Regulatory Commission (NRC) and its Advisory Committee for Reactor Safeguards (ACRS) reviewed the design limits and procedures in the process of reviewing the Clinch River Breeder Reactor (CRBR) for a construction permit in the late 1970s and early 1980s, and identified issues that needed resolution. In the years since then, the NRC and various contractors have evaluated the applicability of the ASME Code and Code Cases to high-temperature reactor designs such as the VHTGRs, and identified issues that need to be resolved to provide a regulatory basis for licensing. This Report describes: (1) NRC and ACRS safety concerns raised during the licensing process of CRBR , (2) how some of these issues are addressed by the current Subsection NH of the ASME Code; and (3) the material models, design criteria, and analysis methods that need to be added to the ASME Code and Code Cases to cover unresolved regulatory issues for very high temperature service.

Design criteria for a data base management system for a PACS at Georgetown University Hospital

International Nuclear Information System (INIS)

Fahey, F.H.; Wang, P.C.; Mun, S.K.; Choyke, P.L.; Benson, H.R.; Duerinckx, A.; Elliott, L.P.

1986-01-01

A major goal of a radiologic picture archival and communication system (PACS) is to increase the availability of the data to the users who require access to them. This is done by providing the data in a digital form which can be readily communicated and archived. In this manner, the PACS can be seen as a specific example of a data base managements system (DBMS). The PACS/DBMS should organize the data base in such a way as to provide its users with the data they require in a timely and efficient manner. The ability to integrate the variety of data into common data base should lead to a more complete and relevant representation of the available information. A PACS/DBMS is not only unique in the types of data contained in the data base and its different users but also in the volume of data that are entered into the system and transferred within the system each day. Consideration of these characteristics leads to the definition of functional criteria for the PACS/DBMS. This report discusses the criteria that will be used in the design of a DBMS for a PACS at Georgetown University Hospital. (Auth.)

RenderGAN: Generating Realistic Labeled Data

Directory of Open Access Journals (Sweden)

Leon Sixt

2018-06-01

Full Text Available Deep Convolutional Neuronal Networks (DCNNs are showing remarkable performance on many computer vision tasks. Due to their large parameter space, they require many labeled samples when trained in a supervised setting. The costs of annotating data manually can render the use of DCNNs infeasible. We present a novel framework called RenderGAN that can generate large amounts of realistic, labeled images by combining a 3D model and the Generative Adversarial Network framework. In our approach, image augmentations (e.g., lighting, background, and detail are learned from unlabeled data such that the generated images are strikingly realistic while preserving the labels known from the 3D model. We apply the RenderGAN framework to generate images of barcode-like markers that are attached to honeybees. Training a DCNN on data generated by the RenderGAN yields considerably better performance than training it on various baselines.

Neutron star models with realistic high-density equations of state

International Nuclear Information System (INIS)

Malone, R.C.; Johnson, M.B.; Bethe, H.A.

1975-01-01

We calculate neutron star models using four realistic high-density models of the equation of state. We conclude that the maximum mass of a neutron star is unlikely to exceed 2 M/sub sun/. All of the realistic models are consistent with current estimates of the moment of inertia of the Crab pulsar

MULTI-CRITERIA APPROACH FOR DESIGNING SUSTAINABLE DRAINAGE IN MALANG RESIDENTIAL AREA INDONESIA

Directory of Open Access Journals (Sweden)

HAPSARI Ratih Indri

2016-07-01

Full Text Available Environmentally sound approach for sustainable urban drainage could promote infiltration and lower the risk of flooding. This study presents the framework to evaluate the drainage alternatives considering multiple aspects including water quantity, life cycle cost and amenity. This approach is verified through application at a residential area in Malang city Indonesia. Different combinations of drainage components comprising of drainage channels, infiltration wells and biopore absorption holes are assessed regarding runoff reduction, present value of life cycle cost, and willingness to pay for the convenience. The first part describes the effective designs of sustainable drainage components in the houses as well as in the public spaces of the housing. The second part of this study describes the use of analytic hierarchy process for weight assignment of sustainability criteria and multiple benefit calculation. The study recommends infiltration wells and biopore absorption holes together with drainage channels as the best management practice of sustainable drainage system based on its overall sustainability index.

NWTS conceptual reference repository description (CRRD). Volume III. Criteria, bases, special studies, and codes

International Nuclear Information System (INIS)

1981-05-01

This volume documents the criteria, design bases, and special studies and provides the backup for the design presented in Volume II. The criteria presented here were developed by ONWI as a draft version for consideration in this conceptual report. Since these criteria were developed subsequent to preparation of the reports used as a basis for the CRRD, not all of the criteria could be fully considered in preparation of the CRRD. However, they were used as guidelines wherever possible. The criteria for terminal storage of waste are still in development. The chapter on the design bases identifies the important design considerations and provides the justification for their selection. The design bases were developed not so much to give exact values for parameters as to identify the parameters that are significant to the design. They also serve as a common basis for coordinating analysis and design studies unitl the next design phase is completed. Some of the design bases presented here were taken directly from the Stearns-Roger NWTS-R1 Conceptual Design Report. The special studies document technical aspects of the design that are of particular importance or that furnish additional information pertaining to the design

Robustness of Adaptive Survey Designs to Inaccuracy of Design Parameters

Directory of Open Access Journals (Sweden)

Burger Joep

2017-09-01

Full Text Available Adaptive survey designs (ASDs optimize design features, given 1 the interactions between the design features and characteristics of sampling units and 2 a set of constraints, such as a budget and a minimum number of respondents. Estimation of the interactions is subject to both random and systematic error. In this article, we propose and evaluate four viewpoints to assess robustness of ASDs to inaccuracy of design parameter estimates: the effect of both imprecision and bias on both ASD structure and ASD performance. We additionally propose three distance measures to compare the structure of ASDs. The methodology is illustrated using a simple simulation study and a more complex but realistic case study on the Dutch Travel Survey. The proposed methodology can be applied to other ASD optimization problems. In our simulation study and case study, the ASD was fairly robust to imprecision, but not to realistic dynamics in the design parameters. To deal with the sensitivity of ASDs to changing design parameters, we recommend to learn and update the design parameters.

Bell Operator Method to Classify Local Realistic Theories

International Nuclear Information System (INIS)

Nagata, Koji

2010-01-01

We review the historical fact of multipartite Bell inequalities with an arbitrary number of settings. An explicit local realistic model for the values of a correlation function, given in a two-setting Bell experiment (two-setting model), works only for the specific set of settings in the given experiment, but cannot construct a local realistic model for the values of a correlation function, given in a continuous-infinite settings Bell experiment (infinite-setting model), even though there exist two-setting models for all directions in space. Hence, the two-setting model does not have the property that the infinite-setting model has. Here, we show that an explicit two-setting model cannot construct a local realistic model for the values of a correlation function, given in an M-setting Bell experiment (M-setting model), even though there exist two-setting models for the M measurement directions chosen in the given M-setting experiment. Hence, the two-setting model does not have the property that the M-setting model has. (general)

Do Preschoolers Recognize The Emotional Expressiveness of Colors in Realistic and Abstract Art Paintings?

Science.gov (United States)

Pouliou, Dimitra; Bonoti, Fotini; Nikonanou, Niki

2018-01-01

The present study was designed to examine preschoolers' ability to recognize the emotional expressiveness of an art painting, through its colors. To attain this aim 78 children, 3-5 years old were presented with realistic and abstract paintings conveying either happiness or sadness and were asked to choose those which matched the appropriate emotion. In total 16 paintings were used, which varied in color, while their subject matter was held as constant as possible after they had been previously rated by a group of adults to ensure that they conveyed the two emotions under investigation. Results showed that children's ability to recognize the emotional expressiveness of a painting through its colors appears at 3 years old and increases significantly at 4 and 5 years old. It was also found that the mood of happiness was more easily recognized than that of sadness, while the style of art paintings (realistic vs. abstract) did not affect children's ability to recognize emotions.

Design criteria for mobile phones: a teenagers perspective.

CSIR Research Space (South Africa)

Batchelor, J

2009-09-01

Full Text Available on mobile phones without blindly following criteria as observed - because there was no anchor they had to set the benchmarks for themselves. A student went even further, reflecting on long-term prospects of the project, remarking: “It is a project...-suited to mobile phones, due to obvious limitations of screen size and resolution, audio and memory restrictions. Low cost and affordable mobile phones in Africa are developing a new conduit for learning, and are gradually influencing the way we view...

Comparison between disign criteria and observed structural performance of underground openings at WIPP

International Nuclear Information System (INIS)

Cook, R.F.; Francke, C.

1989-01-01

This paper discusses the observed structural performance of the underground excavations at the Waste Isolation Pilot Plant (WIPP) in relation to design criteria. The criteria were established at an early stage of the project to define the functional and structural requirements that were to be addressed in the design of the facility. For the underground structural response, the criteria defined the requirements for the shaft and shaft liner design, mine design, waste emplacement, retrievability and instrumentation. The observed structural performance of the underground is determined by the field data that have been collected since excavations were started at the WIPP site. The observations include field measurements of rock and water conditions, as well as maintenance records. The data provide input to design confirmation, performance assessment and form the basis for the design of new underground structures. For this paper, the field data have been compared with the design criteria applicable to ground control to demonstrate that the requirements of the design are met

Verbal versus realistic pictorial representations in conjoint analysis with design attributes

NARCIS (Netherlands)

Vriens, M; Loosschilder, GH; Rosbergen, E; Wittink, DR

The current generation of high-powered graphics software offers an effective means for presenting product designs. Armed with the right tools for generating photorealistic representations of alternative designs, product development teams can obtain useful consumer input about product design

Fatigue - determination of a more realistic usage factor

International Nuclear Information System (INIS)

Lang, H.

2001-01-01

The ability to use a suitable counting method for determining the stress range spectrum in elastic and simplified elastic-plastic fatigue analyses is of crucial importance for enabling determination of a realistic usage factor. Determination of elastic-plastic strain range using the K e factor from fictitious elastically calculated loads is also important in the event of elastic behaviour being exceeded. This paper thus examines both points in detail. A fatigue module with additional options, which functions on this basis is presented. The much more realistic determination of usage factor presented here offers various economic benefits depending on the application

1 CFR 17.3 - Criteria for emergency publication.

Science.gov (United States)

2010-01-01

... 1 General Provisions 1 2010-01-01 2010-01-01 false Criteria for emergency publication. 17.3..., AND PROCESSING OF DOCUMENTS FILING FOR PUBLIC INSPECTION AND PUBLICATION SCHEDULES Emergency Schedule § 17.3 Criteria for emergency publication. The emergency schedule is designed to provide the fastest...

Realistic rhetoric and legal decision

Directory of Open Access Journals (Sweden)

João Maurício Adeodato

2017-06-01

Full Text Available The text aims to lay the foundations of a realistic rhetoric, from the descriptive perspective of how the legal decision actually takes place, without normative considerations. Aristotle's rhetorical idealism and its later prestige reduced rhetoric to the art of persuasion, eliminating important elements of sophistry, especially with regard to legal decision. It concludes with a rhetorical perspective of judicial activism in complex societies.

A methodology and success/failure criteria for determining emergency diesel generator reliability

International Nuclear Information System (INIS)

Wyckoff, H.L.

1986-01-01

In the U.S., comprehensive records of nationwide emergency diesel generator (EDG) reliability at nuclear power plants have not been consistently collected. Those surveys that have been undertaken have not always been complete and accurate. Moreover, they have been based On an extremely conservative methodology and success/failure criteria that are specified in U.S. Nuclear Regulatory Commission Reg. Guide 1.108. This Reg. Guide was one of the NRCs earlier efforts and does not yield the caliber of statistically defensible reliability values that are now needed. On behalf of the U.S. utilities, EPRI is taking the lead in organizing, investigating, and compiling a realistic database of EDG operating success/failure experience for the years 1983, 1984 and 1985. These data will be analyzed to provide an overall picture of EDG reliability. This paper describes the statistical methodology and start and run success/- failure criteria that EPRI is using. The survey is scheduled to be completed in March 1986. (author)

A methodology and success/failure criteria for determining emergency diesel generator reliability

Energy Technology Data Exchange (ETDEWEB)

Wyckoff, H. L. [Electric Power Research Institute, Palo Alto, California (United States)

1986-02-15

In the U.S., comprehensive records of nationwide emergency diesel generator (EDG) reliability at nuclear power plants have not been consistently collected. Those surveys that have been undertaken have not always been complete and accurate. Moreover, they have been based On an extremely conservative methodology and success/failure criteria that are specified in U.S. Nuclear Regulatory Commission Reg. Guide 1.108. This Reg. Guide was one of the NRCs earlier efforts and does not yield the caliber of statistically defensible reliability values that are now needed. On behalf of the U.S. utilities, EPRI is taking the lead in organizing, investigating, and compiling a realistic database of EDG operating success/failure experience for the years 1983, 1984 and 1985. These data will be analyzed to provide an overall picture of EDG reliability. This paper describes the statistical methodology and start and run success/- failure criteria that EPRI is using. The survey is scheduled to be completed in March 1986. (author)

Realistic molecular model of kerogen's nanostructure.

Science.gov (United States)

Bousige, Colin; Ghimbeu, Camélia Matei; Vix-Guterl, Cathie; Pomerantz, Andrew E; Suleimenova, Assiya; Vaughan, Gavin; Garbarino, Gaston; Feygenson, Mikhail; Wildgruber, Christoph; Ulm, Franz-Josef; Pellenq, Roland J-M; Coasne, Benoit

2016-05-01

Despite kerogen's importance as the organic backbone for hydrocarbon production from source rocks such as gas shale, the interplay between kerogen's chemistry, morphology and mechanics remains unexplored. As the environmental impact of shale gas rises, identifying functional relations between its geochemical, transport, elastic and fracture properties from realistic molecular models of kerogens becomes all the more important. Here, by using a hybrid experimental-simulation method, we propose a panel of realistic molecular models of mature and immature kerogens that provide a detailed picture of kerogen's nanostructure without considering the presence of clays and other minerals in shales. We probe the models' strengths and limitations, and show that they predict essential features amenable to experimental validation, including pore distribution, vibrational density of states and stiffness. We also show that kerogen's maturation, which manifests itself as an increase in the sp(2)/sp(3) hybridization ratio, entails a crossover from plastic-to-brittle rupture mechanisms.

A generic approach for steel containment vessel success criteria for severe accident loads

International Nuclear Information System (INIS)

Sammataro, R.F.; Solonick, W.R.; Edwards, N.W.

1993-01-01

Safety has been defined as the foremost design criterion for the Heavy Water New Production Reactor (NPR-HWR) by the U.S. DOE, Office of New Production Reactors (NP). The DOE-NP issued the Deterministic Severe Accident Criteria (DSAC) concept to guide the design of the NPR-HWR containment for resistance to severe accidents. The DSAC concept provides for a generic approach for containment vessel success criteria to predict the threshold of containment failure under severe accident loads. This concept consists of two parts: (1) Problem Statements and (2) Success Criteria. The paper is limited to a discussion of a success criteria. These criteria define acceptable containment response measures and limits for each problem statement. The criteria are based on the 'best estimate' of failure with no conservatism. Rather, conservatism, if required, is to be provided in the problem statements prepared by the designer and/or the regulatory authorities. The success criteria are presented on a multi-tiered basis for static pressure and temperature loadings, dynamic loadings, and missiles that may impact the containment. Within the static pressure and temperature loadings and the dynamic loadings, the criteria are separated into elastic analysis success criteria and inelastic analysis success criteria. Each of these areas, in turn, defines limits on either the stress or strain measures as well as on measures for buckling and displacements. The rationale upon which these criteria are based is contained in referenced documents. Rigorous validation of the criteria by comparison with results from analytical or experimental programs and application of the criteria to a containment design remain as future tasks. (orig./HP)

A realist review of one-to-one breastfeeding peer support experiments conducted in developed country settings.

Science.gov (United States)

Trickey, Heather; Thomson, Gill; Grant, Aimee; Sanders, Julia; Mann, Mala; Murphy, Simon; Paranjothy, Shantini

2018-01-01

The World Health Organisation guidance recommends breastfeeding peer support (BFPS) as part of a strategy to improve breastfeeding rates. In the UK, BFPS is supported by National Institute for Health and Care Excellence guidance and a variety of models are in use. The experimental evidence for BFPS in developed countries is mixed and traditional methods of systematic review are ill-equipped to explore heterogeneity, complexity, and context influences on effectiveness. This review aimed to enhance learning from the experimental evidence base for one-to-one BFPS intervention. Principles of realist review were applied to intervention case studies associated with published experimental studies. The review aimed (a) to explore heterogeneity in theoretical underpinnings and intervention design for one-to-one BFPS intervention; (b) inform design decisions by identifying transferable lessons developed from cross-case comparison of context-mechanism-outcome relationships; and (c) inform evaluation design by identifying context-mechanism-outcome relationships associated with experimental conditions. Findings highlighted poor attention to intervention theory and considerable heterogeneity in BFPS intervention design. Transferable mid-range theories to inform design emerged, which could be grouped into seven categories: (a) congruence with local infant feeding norms, (b) integration with the existing system of health care, (c) overcoming practical and emotional barriers to access, (d) ensuring friendly, competent, and proactive peers, (e) facilitating authentic peer-mother interactions, (f) motivating peers to ensure positive within-intervention amplification, and (g) ensuring positive legacy and maintenance of gains. There is a need to integrate realist principles into evaluation design to improve our understanding of what forms of BFPS work, for whom and under what circumstances. © 2017 John Wiley & Sons Ltd.

Applying air pollution modelling within a multi-criteria decision analysis framework to evaluate UK air quality policies

Science.gov (United States)

Chalabi, Zaid; Milojevic, Ai; Doherty, Ruth M.; Stevenson, David S.; MacKenzie, Ian A.; Milner, James; Vieno, Massimo; Williams, Martin; Wilkinson, Paul

2017-10-01

A decision support system for evaluating UK air quality policies is presented. It combines the output from a chemistry transport model, a health impact model and other impact models within a multi-criteria decision analysis (MCDA) framework. As a proof-of-concept, the MCDA framework is used to evaluate and compare idealized emission reduction policies in four sectors (combustion in energy and transformation industries, non-industrial combustion plants, road transport and agriculture) and across six outcomes or criteria (mortality, health inequality, greenhouse gas emissions, biodiversity, crop yield and air quality legal compliance). To illustrate a realistic use of the MCDA framework, the relative importance of the criteria were elicited from a number of stakeholders acting as proxy policy makers. In the prototype decision problem, we show that reducing emissions from industrial combustion (followed very closely by road transport and agriculture) is more advantageous than equivalent reductions from the other sectors when all the criteria are taken into account. Extensions of the MCDA framework to support policy makers in practice are discussed.

Process, background and design criteria of the gas cleaning at Puertollano IGCC

Energy Technology Data Exchange (ETDEWEB)

Pisa, J. [Elcogas, Madrid (Spain)

1998-11-01

The Puertollano IGCC plant selected cooling by a water-tube boiler with upstream quenching at high velocities that requires a dust-free cooling gas at not less than 250{degree}C in order not to penalise the heat recovery efficiency. A filtration system for gas dedusting in the 250{degree}C temperature range has been installed and will be commissioned at the end of 1997. The gas cleaning concept is completed with a Venturi Scrubber, a COS hydrolysis reactor and a MDEA column to strip the sulphuric acid to yield clean gas. The gasification island is based upon the PRENFLO system which is an entrained-flow system with dry feeding. The selection of the filter system arrangement considered the limited operational experience in comparable operating conditions and acknowledged the flexibility of the filter system versus the cyclone-scrubber as far as easier load variation operation, the reduction of residues needing deposition and increased slag flow, as well as easier maintenance. Additionally to the ceramic test filters in Furstenhausen (PRENFLO) and Deer Park near Houston (SHELL), ceramic candle-type filter were selected in Buggenum and at Wabash River, and for the KoBra plant. The main criteria for the selection of the filter system and the type of candle were: separation efficiency to match clean gas limits; uniform distribution of the dust-laden gas to the filters; wear-resistant routing of the dust-laden gas flow; need for a supporting structure which must cope with sudden pressure fluctuations; optimised pulse gas system; and maintenance and repair. Based upon the above criteria, the PRENFLO concept requirements and the gas turbine specification, an arrangement with two pressure filter vessels with LLB design and filter elements manufactured by Schumacher has been installed in Puertollano. 2 figs., 3 tabs.

On the Realistic Stochastic Model of GPS Observables: Implementation and Performance

Science.gov (United States)

Zangeneh-Nejad, F.; Amiri-Simkooei, A. R.; Sharifi, M. A.; Asgari, J.

2015-12-01

High-precision GPS positioning requires a realistic stochastic model of observables. A realistic GPS stochastic model of observables should take into account different variances for different observation types, correlations among different observables, the satellite elevation dependence of observables precision, and the temporal correlation of observables. Least-squares variance component estimation (LS-VCE) is applied to GPS observables using the geometry-based observation model (GBOM). To model the satellite elevation dependent of GPS observables precision, an exponential model depending on the elevation angles of the satellites are also employed. Temporal correlation of the GPS observables is modelled by using a first-order autoregressive noise model. An important step in the high-precision GPS positioning is double difference integer ambiguity resolution (IAR). The fraction or percentage of success among a number of integer ambiguity fixing is called the success rate. A realistic estimation of the GNSS observables covariance matrix plays an important role in the IAR. We consider the ambiguity resolution success rate for two cases, namely a nominal and a realistic stochastic model of the GPS observables using two GPS data sets collected by the Trimble R8 receiver. The results confirm that applying a more realistic stochastic model can significantly improve the IAR success rate on individual frequencies, either on L1 or on L2. An improvement of 20% was achieved to the empirical success rate results. The results also indicate that introducing the realistic stochastic model leads to a larger standard deviation for the baseline components by a factor of about 2.6 on the data sets considered.

The Formation of Teacher Work Teams under Adverse Conditions: Towards a More Realistic Scenario for Schools in Distress

Science.gov (United States)

Mintrop, Rick; Charles, Jessica

2017-01-01

Group formation studies are rare in the literature on teacher professional learning communities (PLCs). But they are needed to render realistic scenarios and design interventions for practitioners who work in schools where teachers encounter distress and social adversity. Under these conditions, we may need approaches to PLC development that are…

Project C-018H, 242-A Evaporator/PUREX Plant Process Condensate Treatment Facility, functional design criteria. Revision 3

International Nuclear Information System (INIS)

Sullivan, N.

1995-01-01

This document provides the Functional Design Criteria (FDC) for Project C-018H, the 242-A Evaporator and Plutonium-Uranium Extraction (PUREX) Plant Condensate Treatment Facility (Also referred to as the 200 Area Effluent Treatment Facility [ETF]). The project will provide the facilities to treat and dispose of the 242-A Evaporator process condensate (PC), the Plutonium-Uranium Extraction (PUREX) Plant process condensate (PDD), and the PUREX Plant ammonia scrubber distillate (ASD)

Functional design criteria for the 242-A evaporator and PUREX [Plutonium-Uranium Extraction] Plant condensate interim retention basin

International Nuclear Information System (INIS)

Cejka, C.C.

1990-01-01

This document contains the functional design criteria for a 26- million-gallon retention basin and 10 million gallons of temporary storage tanks. The basin and tanks will be used to store 242-A Evaporator process condensate, the Plutonium-Uranium Extraction (PUREX) Plant process distillate discharge stream, and the PUREX Plant ammonia scrubber distillate stream. Completion of the project will allow both the 242-A Evaporator and the PUREX Plant to restart. 4 refs

Photo-Realistic Image Synthesis and Virtual Cinematography

DEFF Research Database (Denmark)

Livatino, Salvatore

2005-01-01

Realistic Virtual View Synthesis is a new field of research that has received increasing attention in recent years. It is strictly related to the grown popularity of virtual reality and the spread of its applications, among which virtual photography and cinematography. The use of computer generated...... characters, "virtual actors", in the motion picture production increases every day. While the most known computer graphics techniques have largely been adopted successfully in nowadays fictions, it still remains very challenging to implement virtual actors which would resemble, visually, human beings....... Interestingly, film directors have been looking at the recent progress achieved by the research community in the field of realistic visualization of virtual views, and they have successfully implemented state of the art research approaches in their productions. An innovative concept is then gaining consensus...

Control system design for electrical stimulation in upper limb rehabilitation modelling, identification and robust performance

CERN Document Server

Freeman, Chris

2016-01-01

This book presents a comprehensive framework for model-based electrical stimulation (ES) controller design, covering the whole process needed to develop a system for helping people with physical impairments perform functional upper limb tasks such as eating, grasping and manipulating objects. The book first demonstrates procedures for modelling and identifying biomechanical models of the response of ES, covering a wide variety of aspects including mechanical support structures, kinematics, electrode placement, tasks, and sensor locations. It then goes on to demonstrate how complex functional activities of daily living can be captured in the form of optimisation problems, and extends ES control design to address this case. It then lays out a design methodology, stability conditions, and robust performance criteria that enable control schemes to be developed systematically and transparently, ensuring that they can operate effectively in the presence of realistic modelling uncertainty, physiological variation an...

Students’ Critical Mathematical Thinking Skills and Character:Experiments for Junior High School Students through Realistic Mathematics Education Culture-Based

Directory of Open Access Journals (Sweden)

Anderson L. Palinussa

2013-01-01

Full Text Available This paper presents the findings of a quasi-experimental with pre-test-post-test design and control group that aims to assess students’ critical mathematical thinking skills and character through realistic mathematics education (RME culture-based. Subjects of this study were 106 junior high school students from two low and medium schools level in Ambon. The instruments of the study are: students’ early math skills test, critical thinking skills mathematical test and perception scale of students’character. Data was analyzed by using t-test and Anova. The study found that: 1 Achievements and enhancement of students’ critical mathematical thinking skills who were treated with by realistic mathematics education is better then students’ skills were treated by conventional mathematics education. The differences are considered to: a overall students, b the level of early math skills, and c schools’ level; 2 Quality of students’ character who were treated by realistic mathematics education is better then students’ character who were treated by conventional mathematics education The differences are considered to: a overall students, b the level of early math skills, and c schools’ level  Keywords: Critical Thinking, Students’ Character, Realistic Mathematics Education Culture-Based DOI: http://dx.doi.org/10.22342/jme.4.1.566.75-94

I-Love relations for incompressible stars and realistic stars

Science.gov (United States)

Chan, T. K.; Chan, AtMa P. O.; Leung, P. T.

2015-02-01

In spite of the diversity in the equations of state of nuclear matter, the recently discovered I-Love-Q relations [Yagi and Yunes, Science 341, 365 (2013), 10.1126/science.1236462], which relate the moment of inertia, tidal Love number (deformability), and the spin-induced quadrupole moment of compact stars, hold for various kinds of realistic neutron stars and quark stars. While the physical origin of such universality is still a current issue, the observation that the I-Love-Q relations of incompressible stars can well approximate those of realistic compact stars hints at a new direction to approach the problem. In this paper, by establishing recursive post-Minkowskian expansion for the moment of inertia and the tidal deformability of incompressible stars, we analytically derive the I-Love relation for incompressible stars and show that the so-obtained formula can be used to accurately predict the behavior of realistic compact stars from the Newtonian limit to the maximum mass limit.

Research on performance-based seismic design criteria

Institute of Scientific and Technical Information of China (English)

谢礼立; 马玉宏

2002-01-01

The seismic design criterion adopted in the existing seismic design codes is reviewed. It is pointed out that the presently used seismic design criterion is not satisfied with the requirements of nowadays social and economic development. A new performance-based seismic design criterion that is composed of three components is presented in this paper. It can not only effectively control the economic losses and casualty, but also ensure the building(s function in proper operation during earthquakes. The three components are: classification of seismic design for buildings, determination of seismic design intensity and/or seismic design ground motion for controlling seismic economic losses and casualties, and determination of the importance factors in terms of service periods of buildings. For controlling the seismic human losses, the idea of socially acceptable casualty level is presented and the (Optimal Economic Decision Model( and (Optimal Safe Decision Model( are established. Finally, a new method is recommended for calculating the importance factors of structures by adjusting structures service period on the base of more important structure with longer service period than the conventional ones. Therefore, the more important structure with longer service periods will be designed for higher seismic loads, in case the exceedance probability of seismic hazard in different service period is same.

Structural acceptance criteria Remote Handling Building Tritium Extraction Facility

Energy Technology Data Exchange (ETDEWEB)

Mertz, G.

1999-12-16

This structural acceptance criteria contains the requirements for the structural analysis and design of the Remote Handling Building (RHB) in the Tritium Extraction Facility (TEF). The purpose of this acceptance criteria is to identify the specific criteria and methods that will ensure a structurally robust building that will safely perform its intended function and comply with the applicable Department of Energy (DOE) structural requirements.

Structural acceptance criteria Remote Handling Building Tritium Extraction Facility

International Nuclear Information System (INIS)

Mertz, G.

1999-01-01

This structural acceptance criteria contains the requirements for the structural analysis and design of the Remote Handling Building (RHB) in the Tritium Extraction Facility (TEF). The purpose of this acceptance criteria is to identify the specific criteria and methods that will ensure a structurally robust building that will safely perform its intended function and comply with the applicable Department of Energy (DOE) structural requirements

Recent advances on thermohydraulic simulation of HTR-10 nuclear reactor core using realistic CFD approach

Energy Technology Data Exchange (ETDEWEB)

Silva, Alexandro S., E-mail: alexandrossilva@ifba.edu.br [Instituto Federal de Educacao, Ciencia e Tecnologia da Bahia (IFBA), Vitoria da Conquista, BA (Brazil); Mazaira, Leorlen Y.R., E-mail: leored1984@gmail.com, E-mail: cgh@instec.cu [Instituto Superior de Tecnologias y Ciencias Aplicadas (INSTEC), La Habana (Cuba); Dominguez, Dany S.; Hernandez, Carlos R.G., E-mail: alexandrossilva@gmail.com, E-mail: dsdominguez@gmail.com [Universidade Estadual de Santa Cruz (UESC), Ilheus, BA (Brazil). Programa de Pos-Graduacao em Modelagem Computacional; Lira, Carlos A.B.O., E-mail: cabol@ufpe.br [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil)

2015-07-01

High-temperature gas-cooled reactors (HTGRs) have the potential to be used as possible energy generation sources in the near future, owing to their inherently safe performance by using a large amount of graphite, low power density design, and high conversion efficiency. However, safety is the most important issue for its commercialization in nuclear energy industry. It is very important for safety design and operation of an HTGR to investigate its thermal-hydraulic characteristics. In this article, it was performed the thermal-hydraulic simulation of compressible flow inside the core of the pebble bed reactor HTR (High Temperature Reactor)-10 using Computational Fluid Dynamics (CFD). The realistic approach was used, where every closely packed pebble is realistically modelled considering a graphite layer and sphere of fuel. Due to the high computational cost is impossible simulate the full core; therefore, the geometry used is a FCC (Face Centered Cubic) cell with the half height of the core, with 21 layers and 95 pebbles. The input data used were taken from the thermal-hydraulic IAEA Bechmark. The results show the profiles of velocity and temperature of the coolant in the core, and the temperature distribution inside the pebbles. The maximum temperatures in the pebbles do not exceed the allowable limit for this type of nuclear fuel. (author)

Recent advances on thermohydraulic simulation of HTR-10 nuclear reactor core using realistic CFD approach

International Nuclear Information System (INIS)

Silva, Alexandro S.; Mazaira, Leorlen Y.R.; Dominguez, Dany S.; Hernandez, Carlos R.G.

2015-01-01

High-temperature gas-cooled reactors (HTGRs) have the potential to be used as possible energy generation sources in the near future, owing to their inherently safe performance by using a large amount of graphite, low power density design, and high conversion efficiency. However, safety is the most important issue for its commercialization in nuclear energy industry. It is very important for safety design and operation of an HTGR to investigate its thermal-hydraulic characteristics. In this article, it was performed the thermal-hydraulic simulation of compressible flow inside the core of the pebble bed reactor HTR (High Temperature Reactor)-10 using Computational Fluid Dynamics (CFD). The realistic approach was used, where every closely packed pebble is realistically modelled considering a graphite layer and sphere of fuel. Due to the high computational cost is impossible simulate the full core; therefore, the geometry used is a FCC (Face Centered Cubic) cell with the half height of the core, with 21 layers and 95 pebbles. The input data used were taken from the thermal-hydraulic IAEA Bechmark. The results show the profiles of velocity and temperature of the coolant in the core, and the temperature distribution inside the pebbles. The maximum temperatures in the pebbles do not exceed the allowable limit for this type of nuclear fuel. (author)

Hyper-realistic face masks: a new challenge in person identification.

Science.gov (United States)

Sanders, Jet Gabrielle; Ueda, Yoshiyuki; Minemoto, Kazusa; Noyes, Eilidh; Yoshikawa, Sakiko; Jenkins, Rob

2017-01-01

We often identify people using face images. This is true in occupational settings such as passport control as well as in everyday social environments. Mapping between images and identities assumes that facial appearance is stable within certain bounds. For example, a person's apparent age, gender and ethnicity change slowly, if at all. It also assumes that deliberate changes beyond these bounds (i.e., disguises) would be easy to spot. Hyper-realistic face masks overturn these assumptions by allowing the wearer to look like an entirely different person. If unnoticed, these masks break the link between facial appearance and personal identity, with clear implications for applied face recognition. However, to date, no one has assessed the realism of these masks, or specified conditions under which they may be accepted as real faces. Herein, we examined incidental detection of unexpected but attended hyper-realistic masks in both photographic and live presentations. Experiment 1 (UK; n = 60) revealed no evidence for overt detection of hyper-realistic masks among real face photos, and little evidence of covert detection. Experiment 2 (Japan; n = 60) extended these findings to different masks, mask-wearers and participant pools. In Experiment 3 (UK and Japan; n = 407), passers-by failed to notice that a live confederate was wearing a hyper-realistic mask and showed limited evidence of covert detection, even at close viewing distance (5 vs. 20 m). Across all of these studies, viewers accepted hyper-realistic masks as real faces. Specific countermeasures will be required if detection rates are to be improved.

HAMMLAB 1999 experimental control room: design - design rationale - experiences

International Nuclear Information System (INIS)

Foerdestroemmen, N. T.; Meyer, B. D.; Saarni, R.

1999-01-01

A presentation of HAMMLAB 1999 experimental control room, and the accumulated experiences gathered in the areas of design and design rationale as well as user experiences. It is concluded that HAMMLAB 1999 experimental control room is a realistic, compact and efficient control room well suited as an Advanced NPP Control Room (ml)

Realistic searches on stretched exponential networks

Indian Academy of Sciences (India)

We consider navigation or search schemes on networks which have a degree distribution of the form () ∝ exp(−). In addition, the linking probability is taken to be dependent on social distances and is governed by a parameter . The searches are realistic in the sense that not all search chains can be completed.

Robust, nonlinear, high angle-of-attack control design for a supermaneuverable vehicle

Science.gov (United States)

Adams, Richard J.

1993-01-01

High angle-of-attack flight control laws are developed for a supermaneuverable fighter aircraft. The methods of dynamic inversion and structured singular value synthesis are combined into an approach which addresses both the nonlinearity and robustness problems of flight at extreme operating conditions. The primary purpose of the dynamic inversion control elements is to linearize the vehicle response across the flight envelope. Structured singular value synthesis is used to design a dynamic controller which provides robust tracking to pilot commands. The resulting control system achieves desired flying qualities and guarantees a large margin of robustness to uncertainties for high angle-of-attack flight conditions. The results of linear simulation and structured singular value stability analysis are presented to demonstrate satisfaction of the design criteria. High fidelity nonlinear simulation results show that the combined dynamics inversion/structured singular value synthesis control law achieves a high level of performance in a realistic environment.

HWVP compliance with the Hanford site solid waste acceptance criteria

International Nuclear Information System (INIS)

Bromm, R.; Ornelas, J.; Fundingsland, S.; Shah, K.

1993-01-01

In order to ensure that the Hanford Waste Vitrification Project (HWVP) will meet solid waste acceptance criteria, a review of the criteria was performed. The primary purpose of the study was to evaluate the modifications that will be required to bring the HWVP into compliance for secondary waste which will be generated during normal operations of the facility. To accomplish this objective, the current HWVP design was evaluated based on the criteria established. Once the non-compliance areas and potentially non-compliance areas were identified, alternative plant design modifications were proposed. This paper summarizes the results and recommendations of that study

Realistic bandwidth estimation in the theoretically predicted radionuclide inventory of PWR-UO2 spent fuel derived from reactor design and operating data

International Nuclear Information System (INIS)

Fast, Ivan

2017-01-01

Nuclear energy for power generation produces heat-generating high- and intermediate level radioactive waste (HLW and ILW) for which a safe solution for the handling and disposal has to be found. Currently, many European countries consider the final disposal of HLW and ILW in deep geological formations as the most preferable option. In Germany the main stream of HLW and ILW include spent fuel assemblies from nuclear power plants (NPPs), the vitrified waste and compacted metallic waste of the fuel assembly structural parts originate from reprocessing plants. An important task that occurs within the framework of the Product Quality Control (PQC) of nuclear waste is the assessment of the compliance of any reprocessed waste product inventory with the prescribed limits for each relevant radionuclide (RN). The PQC task is to verify the required quality and safety of nuclear waste prior to transportation to a German repository and to avert the disposal of non-conform waste packages. The verification is usually based on comparing the declared radionuclide inventory of the waste with the presumed or expected composition, which is estimated, based on the known history of the waste and its processing. The difficulty of such estimations for radioactive components from nuclear fuel assemblies is that reactor design parameters and operating histories can have a significant influence on the nuclide inventory of any individual fuel assembly. Thus, knowledge of these parameters is a key issue to determine the realistic concentration ranges, or bandwidths, of the radionuclide inventory. As soon as a governmental decision on the construction of a high-level waste repository will be made, comprehensive radionuclide inventories of the wastes assigned for the deposition will be required. The list of final repository relevant radionuclide is based on the safety assessment for this particular repository, thus it is likely to comprise more-or-less the same radionuclides that need to be

Realistic bandwidth estimation in the theoretically predicted radionuclide inventory of PWR-UO2 spent fuel derived from reactor design and operating data

Energy Technology Data Exchange (ETDEWEB)

Fast, Ivan

2017-06-01

Nuclear energy for power generation produces heat-generating high- and intermediate level radioactive waste (HLW and ILW) for which a safe solution for the handling and disposal has to be found. Currently, many European countries consider the final disposal of HLW and ILW in deep geological formations as the most preferable option. In Germany the main stream of HLW and ILW include spent fuel assemblies from nuclear power plants (NPPs), the vitrified waste and compacted metallic waste of the fuel assembly structural parts originate from reprocessing plants. An important task that occurs within the framework of the Product Quality Control (PQC) of nuclear waste is the assessment of the compliance of any reprocessed waste product inventory with the prescribed limits for each relevant radionuclide (RN). The PQC task is to verify the required quality and safety of nuclear waste prior to transportation to a German repository and to avert the disposal of non-conform waste packages. The verification is usually based on comparing the declared radionuclide inventory of the waste with the presumed or expected composition, which is estimated, based on the known history of the waste and its processing. The difficulty of such estimations for radioactive components from nuclear fuel assemblies is that reactor design parameters and operating histories can have a significant influence on the nuclide inventory of any individual fuel assembly. Thus, knowledge of these parameters is a key issue to determine the realistic concentration ranges, or bandwidths, of the radionuclide inventory. As soon as a governmental decision on the construction of a high-level waste repository will be made, comprehensive radionuclide inventories of the wastes assigned for the deposition will be required. The list of final repository relevant radionuclide is based on the safety assessment for this particular repository, thus it is likely to comprise more-or-less the same radionuclides that need to be

Results of recent calculations using realistic potentials

International Nuclear Information System (INIS)

Friar, J.L.

1987-01-01

Results of recent calculations for the triton using realistic potentials with strong tensor forces are reviewed, with an emphasis on progress made using the many different calculational schemes. Several test problems are suggested. 49 refs., 5 figs

Accident analysis and DOE criteria

International Nuclear Information System (INIS)

Graf, J.M.; Elder, J.C.

1982-01-01

In analyzing the radiological consequences of major accidents at DOE facilities one finds that many facilities fall so far below the limits of DOE Order 6430 that compliance is easily demonstrated by simple analysis. For those cases where the amount of radioactive material and the dispersive energy available are enough for accident consequences to approach the limits, the models and assumptions used become critical. In some cases the models themselves are the difference between meeting the criteria or not meeting them. Further, in one case, we found that not only did the selection of models determine compliance but the selection of applicable criteria from different chapters of Order 6430 also made the difference. DOE has recognized the problem of different criteria in different chapters applying to one facility, and has proceeded to make changes for the sake of consistency. We have proposed to outline the specific steps needed in an accident analysis and suggest appropriate models, parameters, and assumptions. As a result we feed DOE siting and design criteria will be more fairly and consistently applied

Comprehensive Evaluation Criteria for English Learning Websites Using Expert Validity Surveys

Science.gov (United States)

Yang, Ya-Ting C.; Chan, Chia-Ying

2008-01-01

This study aimed to develop a set of evaluation criteria for English learning websites. These criteria can assist English teachers/web designers in designing effective websites for their English courses and can also guide English learners in screening for appropriate and reliable websites to use in increasing their English ability. To fulfill our…

STURM: Resuspension mesocosms with realistic bottom shear stress and water column turbulence for benthic-pelagic coupling studies: Design and Applications

Science.gov (United States)

Sanford, L. P.; Porter, E.; Porter, F. S.; Mason, R. P.

2016-02-01

Shear TUrbulence Resuspension Mesocosm (STURM) tanks, with high instantaneous bottom shear stress and realistic water column mixing in a single system, allow more realistic benthic-pelagic coupling studies that include sediment resuspension. The 1 m3 tanks can be programmed to produce tidal or episodic sediment resuspension over extended time periods (e.g. 4 weeks), over muddy sediments with or without infaunal organisms. The STURM tanks use a resuspension paddle that produces uniform bottom shear stress across the sediment surface while gently mixing a 1 m deep overlying water column. The STURM tanks can be programmed to different magnitudes, frequencies, and durations of bottom shear stress (and thus resuspension) with proportional water column turbulence levels over a wide range of mixing settings for benthic-pelagic coupling experiments. Over eight STURM calibration settings, turbulence intensity ranged from 0.55 to 4.52 cm s-1, energy dissipation rate from 0.0032 to 2.65 cm2 s-3, the average bottom shear stress from 0.0068 to 0.19 Pa, and the instantaneous bottom shear stress from 0.07 to 2.0 Pa. Mixing settings can be chosen as desired and/or varied over the experiment, based on the scientific question at hand. We have used the STURM tanks for four 4-week benthic-pelagic coupling ecosystem experiments with tidal resuspension with or without infaunal bivalves, for stepwise erosion experiments with and without infaunal bivalves, for experiments on oyster biodeposit resuspension, to mimic storms overlain on tidal resuspension, and for experiments on the effects of varying frequency and duration of resuspension on the release of sedimentary contaminants. The large size of the tanks allows water quality and particle measurements using standard oceanographic instrumentation. The realistic scale and complexity of the contained ecosystems has revealed indirect feedbacks and responses that are not observable in smaller, less complex experimental systems.

Simple and Realistic Data Generation

DEFF Research Database (Denmark)

Pedersen, Kenneth Houkjær; Torp, Kristian; Wind, Rico

2006-01-01

This paper presents a generic, DBMS independent, and highly extensible relational data generation tool. The tool can efficiently generate realistic test data for OLTP, OLAP, and data streaming applications. The tool uses a graph model to direct the data generation. This model makes it very simple...... to generate data even for large database schemas with complex inter- and intra table relationships. The model also makes it possible to generate data with very accurate characteristics....

Thermal comfort. Design criteria for heating and cooling load calculations; Thermische Behaglichkeit. Auslegungskriterien fuer Heiz- und Kuehllastberechnungen

Energy Technology Data Exchange (ETDEWEB)

Nadler, Norbert [CSE Nadler, Oranienburg (Germany)

2010-07-01

Due to the publication of the regulation DIN EN 15 251, the design criteria for the thermal indoor climate during the cooling load calculation and heating load calculation also are specified on European level. The regulation determines that the design values for the operational ambient temperature can be determined from the percentage of the dissatisfied values (PPD value according to DIN EN ISO 773). On national level, the exact definition is to take place for typical activities and thermal insulation values of the clothing. Alternatively, the direct use of the PPD value during the layout also is possible. It is shown that this method is to be preferred and that the most cooling load programs available at the market do not correspond to the generally accepted rules of the technology any longer.

Design criteria for the electrical system in advanced passive reactors. Special features of the AP-600 Reactor

International Nuclear Information System (INIS)

Moraleda Lopez, A.

1997-01-01

The design of the electrical system of an Passive Advanced Reactor is determined by the concept of passive actuation of safety systems, simplification of process systems and optimisation of equipment performance. The system that results from these criteria is very different to those designed for present plants. The main differences are: No class 1E alternating current systems No emergency diesel generators Fewer safety and non-safety class electricity consumers System for continuous monitoring of battery status Use of electronic speed regulators for reactor feedwater pump motors Outsite battery backup safety power supply Motor-operated valves are the only safety electrical actuators Portable power supply for post 72 hour equipment This paper develops these concepts and applies them to the AP-600 project and describes the electrical system of this type of plant. (Author)

Nonreactor nuclear facilities: standards and criteria guide

International Nuclear Information System (INIS)

Brynda, W.J.; Junker, L.; Karol, R.C.; Lobner, P.R.; Goldman, L.A.

1981-09-01

This guide is a source document that identifies standards, codes, and guides that address the nuclear safety considerations pertinent to nuclear facilities as defined in DOE Order 5480.1, Chapter V, Safety of Nuclear Facilities. The guidance and criteria provided are directed toward areas of safety usually addressed in a Safety Analysis Report. The areas of safety include, but are not limited to, siting, principal design criteria and safety system design guidelines, radiation protection, accident analysis, and quality assurance. The guide is divided into two sections: general guidelines and appendices. Those guidelines that are broadly applicable to most nuclear facilities are presented in the general guidelines. These general guidelines may have limited applicability to subsurface facilities such as waste repositories. Guidelines specific to the various types or categories of nuclear facilities are presented in the appendices. These facility-specific appendices provide guidelines and identify standards and criteria that should be considered in addition to, or in lieu of, the general guidelines

Nonreactor nuclear facilities: Standards and criteria guide

International Nuclear Information System (INIS)

Brynda, W.J.; Scarlett, C.H.; Tanguay, G.E.; Lobner, P.R.

1986-09-01

This guide is a source document that identifies standards, codes, and guides that address the nuclear safety considerations pertinent to nuclear facilities as defined in DOE 5480.1A, Chapter V, ''Safety of Nuclear Facilities.'' The guidance and criteria provided is directed toward areas of safety usually addressed in a Safety Analysis Report. The areas of safety include, but are not limited to, siting, principal design criteria and safety system design guidelines, radiation protection, accident analysis, conduct of operations, and quality assurance. The guide is divided into two sections: general guidelines and appendices. Those guidelines that are broadly applicable to most nuclear facilities are presented in the general guidelines. Guidelines specific to the various types or categories of nuclear facilities are presented in the appendices. These facility-specific appendices provide guidelines and identify standards and criteria that should be considered in addition to, or in lieu of, the general guidelines. 25 figs., 62 tabs

Strain limit criteria to predict failure

International Nuclear Information System (INIS)

Flanders, H.E.

1995-01-01

In recent years extensive effort has been expended to qualify existing structures for conditions that are beyond the original design basis. Determination of the component failure load is useful for this type of evaluation. This paper presents criteria based upon strain limits to predict the load at failure. The failure modes addressed are excessive plastic deformations, localized plastic strains, and structural instability. The effects of analytical method sophistication, as built configurations, material properties degradation, and stress state are addressed by the criteria

Realistic Approach for Phasor Measurement Unit Placement

DEFF Research Database (Denmark)

Rather, Zakir Hussain; Chen, Zhe; Thøgersen, Paul

2015-01-01

This paper presents a realistic cost-effectivemodel for optimal placement of phasor measurement units (PMUs) for complete observability of a power system considering practical cost implications. The proposed model considers hidden or otherwise unaccounted practical costs involved in PMU...... installation. Consideration of these hidden but significant and integral part of total PMU installation costs was inspired from practical experience on a real-life project. The proposedmodel focuses on the minimization of total realistic costs instead of a widely used theoretical concept of a minimal number...... of PMUs. The proposed model has been applied to IEEE 14-bus, IEEE 24-bus, IEEE 30-bus, New England 39-bus, and large power system of 300 buses and real life Danish grid. A comparison of the presented results with those reported by traditionalmethods has also been shown to justify the effectiveness...

Idaho CERCLA Disposal Facility Complex Waste Acceptance Criteria